Mechanical behaviour of Astm A 297 grade Hp joints welded using different processes

International Nuclear Information System (INIS)

Emygdio, Paulo Roberto Oliveira; Zeemann, Annelise; Almeida, Luiz Henrique de

1996-01-01

The influence of different arc welding processes on mechanical behaviour was studied for cast heat resistant stainless steel welded joints, in the as welded conditions. ASTM A 297 grade HP with niobium and niobium/titanium additions were welded following three different welding procedures, using shielded metal arc welding gas tungsten arc welding and plasma arc welding, in six welded joints. The welded joint mechanical behaviour was evaluated by ambient temperature and 870 deg C tensile tests; and creep tests at 900 deg C and 50 MPa. Mechanical test results showed that the welding procedure qualification following welding codes is not suitable for high temperature service applications. (author)

Effect of temperature on volume change behaviour of statically compacted kaolin clay

Directory of Open Access Journals (Sweden)

Ileme Ogechi

2016-01-01

Full Text Available Several soils are subjected to high temperature due to the environment where they are located or activities around them. For instance, upper layer of soils in tropical regions, soils around geothermal structures, clay barriers around nuclear waste repository systems. Numerous studies have pointed out that high temperature affects the hydro-mechanical properties of soils. Notwithstanding already existing studies, the influence of temperature on soils is still a challenge, as most of these studies are soil specific and cannot be inferred as the behaviour of all soils. This paper presents an experimental study on the influence of temperature on the volume change behaviour of statically compacted kaolin clay. Compacted samples were tested at varying temperatures using a suction controlled oedometer cell. The influence of temperature on the magnitude of volumetric strain occurring during mechanical and thermal loading was investigated. The study showed that an increase in temperature increased the magnitude of volumetric strain of the soil on loading. Additionally, the results presented in the light of LC curve showed that an increase in temperature resulted in the contraction and a change in the position of the LC curve.

Mechanical behaviour of δ-phase Pu-Ga alloys

International Nuclear Information System (INIS)

Kaschner, G.C.; Stout, M.G.; Hecker, S.S.

2007-01-01

Paper describes a model to ensure prediction of the mechanical behaviour of gallium stabilized plutonium FCC-alloys representing the mechanical threshold strength (MSS) constitutive model based on the effect of temperature, of strain rate, of grain size and of alloy composition. One performed the comparative analysis of the design data derived by means of the elaborated mathematical techniques and of the published results of the mechanical tests of Pu-Ga system various alloys. The model is shown to be adequate to predict the tensile strength and the yield strength values [ru

Effect of temperature and strain rate on the compressive behaviour of supramolecular polyurethane

Directory of Open Access Journals (Sweden)

Tang Xuegang

2015-01-01

Full Text Available Supramolecular polyurethanes (SPUs possess thermoresponsive and thermoreversible properties, and those characteristics are highly desirable in both bulk commodity and value-added applications such as adhesives, shape-memory materials, healable coatings and lightweight, impact-resistant structures (e.g. protection for mobile electronics. A better understanding of the mechanical properties, especially the rate and temperature sensitivity, of these materials are required to assess their suitability for different applications. In this paper, a newly developed SPU with tuneable thermal properties was studied, and the response of this SPU to compressive loading over strain rates from 10−3 to 104 s−1 was presented. Furthermore, the effect of temperature on the mechanical response was also demonstrated. The sample was tested using an Instron mechanical testing machine for quasi-static loading, a home-made hydraulic system for moderate rates and a traditional split Hopkinson pressure bars (SHPBs for high strain rates. Results showed that the compression stress-strain behaviour was affected significantly by the thermoresponsive nature of SPU, but that, as expected for polymeric materials, the general trends of the temperature and the rate dependence mirror each other. However, this behaviour is more complicated than observed for many other polymeric materials, as a result of the richer range of transitions that influence the behaviour over the range of temperatures and strain rates tested.

Temperature effect on the poro-mechanical or hydraulic behaviour of a carbonated rock and a mortar: experimental studies; Influence de la temperature sur le comportement poromecanique ou hydraulique d'une roche carbonatee et d'un mortier: etudes experimentales

Energy Technology Data Exchange (ETDEWEB)

Lion, M

2004-07-15

The main objective of this study is to evaluate the temperature effect on the hydraulic and poro-mechanical behaviour of a limestone. Many experimental tests (porosity and permeability measurements, uniaxial and hydrostatic compressions tests) were carried out in order to study the thermal treatments effect and so the thermal microcracking effect on rock behaviour. Moreover, an experimental device for permeability measurements under high temperatures (until 200 C) was realized. This experimental device permitted to study the permeability variation of the limestone under thermal stresses. Finally, the behaviour of cementitious materials was studied; the temperature effect on the permeability of a mortar was examined. (author)

High temperature mechanical behaviour of glass-ceramics in the YSiAlON and ErSiAlON systems

Energy Technology Data Exchange (ETDEWEB)

Bondanini, A.; Massouras, G.; Besson, J.L. [ENSCI, Limoges (France). SPCTS

2002-07-01

The high temperature mechanical behaviour of oxynitride glass-ceramics in the YSiAlON and ErSiAlON systems was studied in the 950-1150 C temperature range under compressive stresses ranging from 20 to 100 MPa. The parent glass had a composition of 35 Y(or Er)-45 Si-20 Al-83 O-17 N in equivalent percent. Starting from these glasses, glass-ceramics were prepared using a two stage heat treatment: nucleation at the optimum nucleation temperature followed by crystal growth at 1050, 1150 or 1250 C. The two parent glasses had similar viscosities, with that of the Er-glass being slightly less than that of the Y-glass. After the devitrification treatment at 1050 C, B-phase (M{sub 2}SiAlO{sub 5}N) was the only crystalline phase formed in both systems. The creep behaviour was similar for the yttrium and the erbium materials. It was characterised by a long transient stage, due to the viscoelastic response of the residual glass, with recovered strain after unloading decreasing as loading time increased. The creep resistance was compared to that of the parent glasses in terms of apparent viscosity. The crystallisation of 75% of the glass resulted in an increase in viscosity such that a temperature some 100 C higher showed the same viscosity value. After heat treatment at 1150 C, the phase assemblage in the yttrium material changed with the formation of wollastonite and partial conversion of B-phase into Iw-phase. The apparent viscosity was 2 orders of magnitude higher than that of the samples heat treated at 1050 C and no strain recovery was observed upon unloading. In contrast, the erbium materials retained the same microstructure as after the heat treatment at 1050{sup b}C and there was no difference in the creep behaviour of the samples heat treated at 1050 or 1150 C. After a crystallisation treatment at 1250 C of the yttrium parent glass, the glass-ceramic consisted of yttrium aluminium garnet, N-apatite and {beta}-Y{sub 2}Si{sub 2}O{sub 7} and showed excellent creep

Hormonal mechanisms of cooperative behaviour

Science.gov (United States)

Soares, Marta C.; Bshary, Redouan; Fusani, Leonida; Goymann, Wolfgang; Hau, Michaela; Hirschenhauser, Katharina; Oliveira, Rui F.

2010-01-01

Research on the diversity, evolution and stability of cooperative behaviour has generated a considerable body of work. As concepts simplify the real world, theoretical solutions are typically also simple. Real behaviour, in contrast, is often much more diverse. Such diversity, which is increasingly acknowledged to help in stabilizing cooperative outcomes, warrants detailed research about the proximate mechanisms underlying decision-making. Our aim here is to focus on the potential role of neuroendocrine mechanisms on the regulation of the expression of cooperative behaviour in vertebrates. We first provide a brief introduction into the neuroendocrine basis of social behaviour. We then evaluate how hormones may influence known cognitive modules that are involved in decision-making processes that may lead to cooperative behaviour. Based on this evaluation, we will discuss specific examples of how hormones may contribute to the variability of cooperative behaviour at three different levels: (i) within an individual; (ii) between individuals and (iii) between species. We hope that these ideas spur increased research on the behavioural endocrinology of cooperation. PMID:20679116

Geomechanical behaviour of boom clay under ambient and elevated temperature conditions

International Nuclear Information System (INIS)

Neerdael, B.; Beaufays, R.; Buyens, M.; Bruyn, D. de; Voet, M.

1992-01-01

This research is focused upon in-situ investigations related to the (thermo-) mechanical behaviour of clay. Three main items are covered in this research area: Stress measurements around the underground research facility for radioactive waste disposal using hydraulical stress monitoring stations; detection of micro-fractures in the clay host, mainly using geophysical seismic techniques; long term mechanical behaviour of clay (this last item, studied by ANDRA at Mol, is not described in this paper). The stress monitoring stations appear to be more reliable in getting relative pressure variations with time rather than absolute values of stress, even after studying and improving the characteristics of the surrounding grout. The seismic techniques used to appear to be sensitive and accurate enough for detecting induced fracturation in the clay host, even for the low temperature. This is also in agreement with bench-scale experiments on clay samples intended to quantify the influence of both temperature and consolidation on the velocity. 10 refs., 80 figs., 3 tabs

Experimental study of thermo-hydro-mechanical behaviour of Callovo-Oxfordian Clay-stone

International Nuclear Information System (INIS)

Mohajerani, M.

2011-01-01

During the different phases of the exothermic radioactive waste deep disposal (excavation, operation) and after permanent closure, the host rock is submitted to various coupled mechanical, hydraulic and thermal phenomena. Hence, a thorough investigation of the thermo-hydro-mechanical behaviour of the rock is necessary to complete existing data and to better understand and model the short and long term behaviour of the Callovo-Oxfordian (COx) clay formation in Bure (Meuse/Haute-Marne - M/HM), considered by ANDRA as a potential host rock in France.In this work, the compression - swelling behaviour of the COx Clay-stone was first investigated by carrying out a series of high-pressure oedometric tests. The results, interpreted in terms of coupling between damage and swelling, showed that the magnitude of swelling was linked to the density of the fissures created during compression. In a second step, the hydro-mechanical and thermo-hydro-mechanical behaviour of the saturated Clay-stone under a mean stress close to the in situ one were investigated by using two devices with short drainage path (10 mm), namely a isotropic cell and a newly designed hollow cylinder triaxial cell with local displacement measurements. These devices helped to solve two majors problems related to testing very low permeability materials: i) a satisfactory previous sample saturation (indicated by good Skempton values) and ii) satisfactory drainage conditions. Some typical constitutive parameters (Skempton and Biot's coefficients, drained and undrained compressibility coefficients) have been determined at ambient temperature through isotropic compression tests that also confirmed the transverse isotropy of the Clay-stone. The consistency of the obtained parameters has been checked in a saturated poro-elastic framework. Two aspects of the thermo-hydro-mechanical behaviour of the COx Clay-stone have then been investigated through different heating tests and through drained and undrained isotropic

On the High Temperature Deformation Behaviour of 2507 Super Duplex Stainless Steel

Science.gov (United States)

Mishra, M. K.; Balasundar, I.; Rao, A. G.; Kashyap, B. P.; Prabhu, N.

2017-02-01

High temperature deformation behaviour of 2507 super duplex stainless steel was investigated by conducting isothermal hot compression tests. The dominant restoration processes in ferrite and austenite phases present in the material were found to be distinct. The possible causes for these differences are discussed. Based on the dynamic materials model, processing map was developed to identify the optimum processing parameters. The microstructural mechanisms operating in the material were identified. A unified strain-compensated constitutive equation was established to describe the high temperature deformation behaviour of the material under the identified processing conditions. Standard statistical parameter such as correlation coefficient has been used to validate the established equation.

Constitutive behaviour of an as-cast AA7050 alloy in the sub-solidus temperature range

International Nuclear Information System (INIS)

Subroto, T A S; Miroux, A G; Eskin, D G; Katgerman, L

2012-01-01

Aluminum alloy 7050 is of interest for aerospace industries due to its superior mechanical properties. However, its inherent solidification behaviour may augment the accumulation of residual stresses due to uneven cooling conditions upon direct-chill (DC) casting. This can increase the propensity of cold cracking (CC), which is a potentially catastrophic phenomenon in casting ingots. To predict the outcome of the aluminum casting process, ALSIM software is utilised. This software has the capability to predict CC susceptibility during the casting process. However, at the moment, ALSIM lacks the information regarding material constitutive behaviour in the sub-solidus temperature range, which is considered important for studying CC phenomenon. At the moment, ALSIM only has a partial constitutive database for AA7050 and misses data, especially in the vicinity of non-equilibrium solidus (NES) point. The present work presents measurements of tensile constitutive parameters in the temperature range between 400 °C and NES, which is for this alloy defined as 465 °C. The mechanical behaviour is tested in a Gleeble 3800 thermo-mechanical simulator. Constitutive parameters such as stress-strain curves, strain-rate sensitivity and ductility of the alloy have been measured at different test temperatures. With these constitutive data, we expect to improve the accuracy of ALSIM simulations in terms of CC prediction, and gain more insight into the evolution of mechanical properties of AA7050 in the temperature nearby the NES.

Plastic behaviour of Zircaloy-4 in the temperature range 77-1000 K

International Nuclear Information System (INIS)

Derep, J.L.; Ibrahim, S.; Rouby, D.; Fantozzi, G.; Gobin, P.

1979-01-01

Tensile tests were carried out on Zircaloy-4 over a temperature range 77-1000 K. So, we have determined the flow stress variations as a function of temperature and strain rate. Two thermally activated zones were observed between about 77 and 600 K, a plateau stress between 600 and 700 K and an other thermally activated zone above 700 K. The various mechanisms which can be responsible for the thermally activated and athermal zones are discussed in the light of experimental results. The mechanical behaviour of Zircaloy-4 appears similar to the zirconium-oxygen alloys one. (orig.) [de

Thermal and mechanical behaviour of an experimental mock-up of a nuclear containment

International Nuclear Information System (INIS)

Chauvel, D.; Barre, F.

2007-01-01

In order to better understand the behaviour of a reactor containment submitted to combined pressure and temperature loads by means of studies of the concrete permeability and the state of cracking evolution, EDF and its French partners have built a prestressed concrete test model which represents a PWR containment typical section. The monitoring system was designed to follow the evolution of strains, temperature and state of cracking of the concrete wall from construction stage to air and steam tests. The measurements results as well as their comparison with theoretical laws or data and calculated values, allow to determine the main thermal and mechanical characteristics of the concrete, to analyse the thermo-mechanical behaviour of the structure and also to check the design criteria of prestressed concrete containments. (authors)

Low-temperature behaviour of the Kob-Andersen binary mixture

International Nuclear Information System (INIS)

Ashwin S S; Sastry, Srikanth

2003-01-01

The dynamical behaviours of glass-forming liquids have been analysed extensively via computer simulations of model liquids, among which the Kob-Andersen binary Lennard-Jones mixture has been a widely studied system. Typically, studies of this model have been restricted to temperatures above the mode coupling temperature. Preliminary results concerning the dynamics of the Kob-Andersen binary mixture are presented at temperatures that extend below the mode coupling temperature, along with properties of the local energy minima sampled. These results show that a crossover in the dynamics occurs alongside changes in the properties of the inherent structures sampled. Furthermore, a crossover is observed from non-Arrhenius behaviour of the diffusivity above the mode coupling temperature to Arrhenius behaviour at lower temperatures

Modeling of the mechanical behaviour of welded structures: behaviour laws and rupture criteria

International Nuclear Information System (INIS)

Paris, T.; Delaplanche, D.; Saanouni, K.

2006-01-01

In the framework of the technological developments carried out in the CEA, the analysis of the mechanical behaviour of the heterogeneous welded bonds Ta/TA6V is a main preoccupation. Indeed, the welding of these two materials which cannot be distinguished by their mechanical and thermal properties induces strong microstructural heterogeneities in the melted zone. In order to characterize the behaviour of the welded joints and to develop a model of mechanical behaviour, a four points bending test on a notched specimen has been developed and implemented. This new test has allowed to obtain a macroscopic response of strength-displacement type but to analyze too more finely, with an optical extensometry and images correlation method, the influence of the heterogeneities on the local deformation of the welded joint. The confrontation of these results to a metallurgical study allows to validate the first conclusions deduced of the mechanical characterization tests and to conclude as for the local mechanisms governing the behaviour and the damage of the melted zone. The mechanical behaviour can be restored by an elasto-viscoplastic model with isotropic and non linear kinematic strain hardening coupled to this damage. The proposed model allows to identify the macroscopic behaviour of the weld bead. (O.M.)

Thermo-Mechanical Behaviour of Flax-Fibre Reinforced Epoxy Laminates for Industrial Applications

Directory of Open Access Journals (Sweden)

Giuseppe Pitarresi

2015-11-01

Full Text Available The present work describes the experimental mechanical characterisation of a natural flax fibre reinforced epoxy polymer composite. A commercial plain woven quasi-unidirectional flax fabric with spun-twisted yarns is employed in particular, as well as unidirectional composite panels manufactured with three techniques: hand-lay-up, vacuum bagging and resin infusion. The stiffness and strength behaviours are investigated under both monotonic and low-cycle fatigue loadings. The analysed material has, in particular, shown a typical bilinear behaviour under pure traction, with a knee yield point occurring at a rather low stress value, after which the material tensile stiffness is significantly reduced. In the present work, such a mechanism is investigated by a phenomenological approach, performing periodical loading/unloading cycles, and repeating tensile tests on previously “yielded” samples to assess the evolution of stiffness behaviour. Infrared thermography is also employed to measure the temperature of specimens during monotonic and cyclic loading. In the first case, the thermal signal is monitored to correlate departures from the thermoelastic behaviour with the onset of energy loss mechanisms. In the case of cyclic loading, the thermoelastic signal and the second harmonic component are both determined in order to investigate the extent of elastic behaviour of the material.

Optimization of tribological behaviour on Al- coconut shell ash composite at elevated temperature

Science.gov (United States)

Siva Sankara Raju, R.; Panigrahi, M. K.; Ganguly, R. I.; Srinivasa Rao, G.

2018-02-01

In this study, determine the tribological behaviour of composite at elevated temperature i.e. 50 - 150 °C. The aluminium matrix composite (AMC) are prepared with compo casting route by volume of reinforcement of coconut shell ash (CSA) such as 5, 10 and 15%. Mechanical properties of composite has enhances with increasing volume of CSA. This study details to optimization of wear behaviour of composite at elevated temperatures. The influencing parameters such as temperature, sliding velocity and sliding distance are considered. The outcome response is wear rate (mm3/m) and coefficient of friction. The experiments are designed based on Taguchi [L9] array. All the experiments are considered as constant load of 10N. Analysis of variance (ANOVA) revealed that temperature is highest influencing factor followed by sliding velocity and sliding distance. Similarly, sliding velocity is most influencing factor followed by temperature and distance on coefficient of friction (COF). Finally, corroborates analytical and regression equation values by confirmation test.

Experimental and numerical study of the mechanical behaviour modelling of a metal-ceramic composite: MoTiC30%

International Nuclear Information System (INIS)

Cedat, D.

2008-11-01

In the scope of refractory materials development for structural applications in the core of the future nuclear reactors, several studies have been developed. The aim of this work is to increase the knowledge of the mechanical behaviour and the damage of the ceramic-metal composite Mo(TiC)x% under the temperature range [25-700 C]. The identification of the third phase, formed by diffusion during the sintering step was identified by microstructural characterization. Experimental study also revealed the percolation of the ceramic particles through the structure. Mechanical tests highlight the main characteristics of the material: the macroscopic behaviour depends on the strain rate on the first hand and the temperature on the other hand. These mechanisms are attributed to the thermally activated behaviour of molybdenum. Simulations have been made on several microstructures considering elastic-brittle inclusion in a viscoelastic matrix. A polycrystalline model was used to simulate the evolution of the mechanical behaviour of the composite. The numerical aggregate, used for the simulation, was built from a 3D reconstruction technique thanks to acquisition of FIB/EBSD/SEM data. (author)

The influence of elevated temperature transformation and mechanical properties of a precipitation hardening martensitic stainless steel on its wear behaviour

International Nuclear Information System (INIS)

Smith, A.F.

1989-11-01

Self wear tests of a martensitic stainless steel in CO 2 in the temperature range 20-300degC showed transitional behaviour at 20 and 300degC. In the mid temperature range a severe wear rate of ∼ 2 x 10 -13 m 3 /Nm persisted for sliding distances up to 2000 m. A possible explanation was that while strain induced transformation of retained austenite at low temperatures provided a sufficiently hardened substrate that allowed inelastic rather than plastic interactions this did not occur at 200degC. Tests were carried out to determine the temperature above which strain no longer transformed austenite into martensite. Although a martensite start temperature of ∼ 150degC was found for the present steel the presence of only ∼ 10% retained austenite in the ''as heat treated'' material suggests that its transformation to martensite at 200degC would not materially affect the extent of subsurface hardening. It is proposed that a surface reaction plays a role in transition behaviour. At 300degC the reaction product is an oxide but at room temperature it is possibly a carbonate. The stability of the carbonate decreases with temperature thus giving an intermediate temperature range where metal/metal contacts prevail leading to the persistent high wear behaviour. (author)

Investigation of the effect of hydride and iodine on the mechanical behaviour of the zircaloy-4

International Nuclear Information System (INIS)

Soares, M.I.

1981-12-01

To investigate the effect of hydride and iodine on the mechanical behaviour of the zircaloy-4 tubes, deformation tests under pressure of samples hydrided in autoclave and of samples containing iodine were carried out, in order to simulate the fission product. The same tests were carried out in samples without hydride and iodine contents that were used as reference samples in the temperature range of 650 0 C-950 0 C. The hydrided samples and the samples containing iodine tested at 650 0 C and 750 0 C showed a higher ductility than the samples of reference. The hydrided samples tested at 850 0 C and 950 0 C showed a higher embritlement than the samples of reference and than the samples containing iodine tested at the same temperatures. A mechanical test has been developed to investigate the effect of hydride and iodine on the mechanical behaviour of the zircaloy-4 tubes. The mechanical test were carried out at room temperature. At room temperature the hydrition decreased the ductility of zircaloy-4. At room temperature the sample containing iodine showed a higher ductility than the sample without iodine. The combined action of hydrogen and iodine at room temperature enhanced the embrittlment of the samples zircaloy-4. (Author) [pt

Mechanical Behaviour of Materials Volume II Fracture Mechanics and Damage

CERN Document Server

François, Dominique; Zaoui, André

2013-01-01

Designing new structural materials, extending lifetimes and guarding against fracture in service are among the preoccupations of engineers, and to deal with these they need to have command of the mechanics of material behaviour. This ought to reflect in the training of students. In this respect, the first volume of this work deals with elastic, elastoplastic, elastoviscoplastic and viscoelastic behaviours; this second volume continues with fracture mechanics and damage, and with contact mechanics, friction and wear. As in Volume I, the treatment links the active mechanisms on the microscopic scale and the laws of macroscopic behaviour. Chapter I is an introduction to the various damage phenomena. Chapter II gives the essential of fracture mechanics. Chapter III is devoted to brittle fracture, chapter IV to ductile fracture and chapter V to the brittle-ductile transition. Chapter VI is a survey of fatigue damage. Chapter VII is devoted to hydogen embrittlement and to environment assisted cracking, chapter VIII...

Mechanical behaviour of Zn–Al–Cu–Mg alloys: Deformation mechanisms of as-cast microstructures

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhicheng; Sandlöbes, Stefanie; Wu, Liang; Hu, Weiping; Gottstein, Günter; Korte-Kerzel, Sandra, E-mail: Korte-Kerzel@imm.rwth-aachen.de

2016-01-10

We study the effects of dilute Mg addition on the microstructure formation and mechanical properties of a ZnAl4Cu1 alloy. On the basis of the composition of the commercial alloy Z410 (4 wt% Al, 1 wt% Cu, and 0.04 wt% Mg), three laboratory alloys with different Mg contents (0.04 wt%, 0.21 wt% and 0.31 wt%) are characterised in terms of their mechanical properties and microstructures using ex-situ and in-situ tensile tests in conjunction with scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Increasing Mg content causes the precipitation of Mg{sub 2}Zn{sub 11} phase precipitates and refined lamellar spacings in the eutectoid phase. The alloy with a medium Mg content (0.21 wt%) exhibits the highest yield strength both at room temperature and at elevated temperatures. Further, we show that dilute Mg alloying causes an improvement of the ductility of ZnAl4Cu1 base-alloys, especially at elevated temperatures. In addition, the alloys reveal two distinct deformation regimes distinguishable close to room temperature and at commonly employed strain rates, with work hardening and brittle fracture exhibited at room temperature and/or elevated strain rate (5×10{sup −4} s{sup −1}), and work softening and ductile fracture at elevated temperature and/or low strain rate (6×10{sup −6} s{sup −1}). The deformation mechanisms and fracture behaviour in both regimes are investigated and the underlying physical mechanisms of the observed phenomena are discussed.

Mechanical behaviour of Zn–Al–Cu–Mg alloys: Deformation mechanisms of as-cast microstructures

International Nuclear Information System (INIS)

Wu, Zhicheng; Sandlöbes, Stefanie; Wu, Liang; Hu, Weiping; Gottstein, Günter; Korte-Kerzel, Sandra

2016-01-01

We study the effects of dilute Mg addition on the microstructure formation and mechanical properties of a ZnAl4Cu1 alloy. On the basis of the composition of the commercial alloy Z410 (4 wt% Al, 1 wt% Cu, and 0.04 wt% Mg), three laboratory alloys with different Mg contents (0.04 wt%, 0.21 wt% and 0.31 wt%) are characterised in terms of their mechanical properties and microstructures using ex-situ and in-situ tensile tests in conjunction with scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Increasing Mg content causes the precipitation of Mg_2Zn_1_1 phase precipitates and refined lamellar spacings in the eutectoid phase. The alloy with a medium Mg content (0.21 wt%) exhibits the highest yield strength both at room temperature and at elevated temperatures. Further, we show that dilute Mg alloying causes an improvement of the ductility of ZnAl4Cu1 base-alloys, especially at elevated temperatures. In addition, the alloys reveal two distinct deformation regimes distinguishable close to room temperature and at commonly employed strain rates, with work hardening and brittle fracture exhibited at room temperature and/or elevated strain rate (5×10"−"4 s"−"1), and work softening and ductile fracture at elevated temperature and/or low strain rate (6×10"−"6 s"−"1). The deformation mechanisms and fracture behaviour in both regimes are investigated and the underlying physical mechanisms of the observed phenomena are discussed.

ELOCA: fuel element behaviour during high temperature transients

International Nuclear Information System (INIS)

Sills, H.E.

1979-03-01

The ELOCA computer code was developed to simulate the uniform thermal-mechanical behaviour of a fuel element during high-temperature transients such as a loss-of-coolant accident (LOCA). Primary emphasis is on the diametral expansion of the fuel sheath. The model assumed is a single UO2/zircaloy-clad element with axisymmetric properties. Physical effects considered by the code are fuel expansion, cracking and melting; variation, during the transient, of internal gas pressure; changing fuel/sheath heat transfer; thermal, elastic and plastic sheath deformation (anisotropic); Zr/H 2 O chemical reaction effects; and beryllium-assisted crack penetration of the sheath. (author)

Intermetallic alloys: Deformation, mechanical and fracture behaviour

International Nuclear Information System (INIS)

Dogan, B.

1988-01-01

The state of the art in intermetallic alloys development with particular emphasis on deformation, mechanical and fracture behaviour is documented. This review paper is prepared to lay the ground stones for a future work on mechanical property characterization and fracture behaviour of intermetallic alloys at GKSS. (orig.)

Low-temperature behaviour of the engine oil

Directory of Open Access Journals (Sweden)

Vojtěch Kumbár

2013-01-01

Full Text Available The behaviour of engine oil is very important. In this paper has been evaluated temperature dependence kinematic viscosity of engine oils in the low temperatures. Five different commercially distributed engine oils (primarily intended for automobile engines with viscosity class 0W–40, 5W–40, 10W–40, 15W–40, and 20W–40 have been evaluated. The temperature dependence kinematic viscosity has been observed in the range of temperature from −15 °C to 15 °C (for all oils. Considerable temperature dependence kinematic viscosity was found and demonstrated in case of all samples, which is in accordance with theoretical assumptions and literature data. Mathematical models have been developed and tested. Temperature dependence dynamic viscosity has been modeled using a polynomials 3rd and 4th degree. The proposed models can be used for prediction of flow behaviour of oils. With monitoring and evaluating we can prevent technical and economic losses.

Mechanical Behaviour of Materials Volume 1 Micro- and Macroscopic Constitutive Behaviour

CERN Document Server

François, Dominique; Zaoui, André

2012-01-01

Advances in technology are demanding ever-increasing mastery over the materials being used: the challenge is to gain a better understanding of their behaviour, and more particularly of the relations between their microstructure and their macroscopic properties.   This work, of which this is the first volume, aims to provide the means by which this challenge may be met. Starting from the mechanics of deformation, it develops the laws governing macroscopic behaviour – expressed as the constitutive equations – always taking account of the physical phenomena which underlie rheological behaviour. The most recent developments are presented, in particular those concerning heterogeneous materials such as metallic alloys, polymers and composites. Each chapter is devoted to one of the major classes of material behaviour.   As the subtitles indicate, Volume 1 deals with micro- and macroscopic constitutive behaviour and Volume 2 with damage and fracture mechanics. A third volume will be devoted to exercises and the...

Mechanical properties and fracture behaviour of defective phosphorene nanotubes under uniaxial tension

Science.gov (United States)

Liu, Ping; Pei, Qing-Xiang; Huang, Wei; Zhang, Yong-Wei

2017-12-01

The easy formation of vacancy defects and the asymmetry in the two sublayers of phosphorene nanotubes (PNTs) may result in brand new mechanical properties and failure behaviour. Herein, we investigate the mechanical properties and fracture behaviour of defective PNTs under uniaxial tension using molecular dynamics simulations. Our simulation results show that atomic vacancies cause local stress concentration and thus significantly reduce the fracture strength and fracture strain of PNTs. More specifically, a 1% defect concentration is able to reduce the fracture strength and fracture strain by as much as 50% and 66%, respectively. Interestingly, the reduction in the mechanical properties is found to depend on the defect location: a defect located in the outer sublayer has a stronger effect than one located in the inner layer, especially for PNTs with a small diameter. Temperature is also found to strongly influence the mechanical properties of both defect-free and defective PNTs. When the temperature is increased from 0 K to 400 K, the fracture strength and fracture strain of defective PNTs with a defect concentration of 1% are reduced further by 71% and 61%, respectively. These findings are of great importance for the structural design of PNTs as building blocks in nanodevices.

An investigation of dynamic mechanical behaviour of Ti6Al4V titanium alloy at room temperature

Directory of Open Access Journals (Sweden)

Ran Chun

2016-01-01

Full Text Available To study the high strain rate shear behaviour of Ti6Al4V titanium alloy, a series of dynamic compression experiments has been performed by split Hopkinson pressure bar (SHPB using Flat Hat-shaped specimen at room temperature. Macro true shear stress-true strain curves were obtained under different strain rate loading conditions at room temperature. The effects of strain hardening and strain rate hardening on the dynamic mechanical properties of Ti6Al4V titanium alloy were discussed. Results indicate that a The higher the strain rate, the higher the flow stress, therefore, the material has obvious strain rate hardening effect, b It is ductile failure for Ti6Al4V titanium alloy under quasi-static loading condition, c For dynamical tests, the values for true shear stress increase with increasing true strain till the maximum true shear stress, on the contrary, the values for true shear stress decrease with increasing the true strain after the maximum true shear stress and d The flow stress increases with increasing the true strain under quasi-static loading condition during the plastic deformation.

Testing Mechanisms for Philanthropic Behaviour

NARCIS (Netherlands)

Bekkers, R.H.F.P.; Wiepking, P.

2011-01-01

This special issue of the International Journal of Nonprofit and Voluntary Sector Marketing presents a collection of nine papers testing mechanisms that drive philanthropic behaviour. By testing one or more specific mechanisms that were derived from the philanthropic literature, the authors of the

Temperature-dependent behaviours are genetically variable in the nematode Caenorhabditis briggsae.

Science.gov (United States)

Stegeman, Gregory W; de Mesquita, Matthew Bueno; Ryu, William S; Cutter, Asher D

2013-03-01

Temperature-dependent behaviours in Caenorhabditis elegans, such as thermotaxis and isothermal tracking, are complex behavioural responses that integrate sensation, foraging and learning, and have driven investigations to discover many essential genetic and neural pathways. The ease of manipulation of the Caenorhabditis model system also has encouraged its application to comparative analyses of phenotypic evolution, particularly contrasts of the classic model C. elegans with C. briggsae. And yet few studies have investigated natural genetic variation in behaviour in any nematode. Here we measure thermotaxis and isothermal tracking behaviour in genetically distinct strains of C. briggsae, further motivated by the latitudinal differentiation in C. briggsae that is associated with temperature-dependent fitness differences in this species. We demonstrate that C. briggsae performs thermotaxis and isothermal tracking largely similar to that of C. elegans, with a tendency to prefer its rearing temperature. Comparisons of these behaviours among strains reveal substantial heritable natural variation within each species that corresponds to three general patterns of behavioural response. However, intraspecific genetic differences in thermal behaviour often exceed interspecific differences. These patterns of temperature-dependent behaviour motivate further development of C. briggsae as a model system for dissecting the genetic underpinnings of complex behavioural traits.

Behaviour of polar crystals at low temperatures

International Nuclear Information System (INIS)

Drozhdin, S.N.; Novik, V.K.; Gavrilova, N.D.; Koptsik, V.A.; Popova, T.V.

1975-01-01

Temperature dependencies of pyrocoefficient for a wide class of various pyroactive crystals in the temperature range from 4,2 to 300 deg K were investigated. The problems to be solved were: to confirm a conclusion on the pyrocoefficient γsup(sigma) tending to zero at T → 0; to compare experimental data with conclusions of existing theories; to reveal specific features in the behaviour of both linear pyroelectrics and segnetoelectrics at low temperatures. The behaviour of the total pyrocoefficient for all crystals obeys the regularity γsup(sigma) → 0 at T → O. In the range of low temperatures the pyrocoefficient varies by the power law: γsup(sigma) approximately Tsup(α). For the majority of crystals studied α is close to 3. CdS, BeO, ZiNbO 3 and other crystals were studied

High temperature fatigue behaviour of TZM molybdenum alloy under mechanical and thermomechanical cyclic loads

International Nuclear Information System (INIS)

Shi, H.J.; Niu, L.S.; Korn, C.; Pluvinage, G.

2000-01-01

High temperature isothermal mechanical fatigue and in-phase thermomechanical fatigue (TMF) tests in load control were carried out on a molybdenum-based alloy, one of the best known of the refractory alloys, TZM. The stress-strain response and the cyclic life of the material were measured during the tests. The fatigue lives obtained in the in-phase TMF tests are lower than those obtained in the isothermal mechanical tests at the same load amplitude. It appears that an additional damage is produced by the reaction of mechanical stress cycles and temperature cycles in TMF situation. Ratcheting phenomenon occurred during the tests with an increasing creep rate and it was dependent on temperature and load amplitude. A model of lifetime prediction, based on the Woehler-Miner law, was discussed. Damage coefficients that are functions of the maximum temperature and the variation of temperature are introduced in the model so as to evaluate TMF lives in load control. With this method the lifetime prediction gives results corresponding well to experimental data

Mechanical and frictional behaviour of nano-porous anodised aluminium

Energy Technology Data Exchange (ETDEWEB)

Tsyntsaru, N., E-mail: tintaru@phys.asm.md [Institute of Applied Physics of ASM, 5 Academy str., Chisinau, MD 2028 (Moldova, Republic of); Kavas, B., E-mail: bkavas@ford.com.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469 Maslak (Turkey); Ford Otomotiv San A.S., Istanbul (Turkey); Sort, J., E-mail: jordi.sort@uab.cat [Institució Catalana de Recerca i Estudis Avançats (ICREA) and Departament de Física, Universitat Autònoma de Barcelona, E-08193 Bellaterra (Spain); Urgen, M., E-mail: urgen@itu.edu.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469 Maslak (Turkey); Celis, J.-P., E-mail: jean-pierre.celis@mtm.kuleuven.be [KU Leuven, Dept. MTM, Kasteelpark Arenberg 44, B-3001 (Belgium)

2014-12-15

The porous structure of anodic aluminium oxide (AAO) can be used in versatile applications such as a lubricant reservoir in self-lubricating systems. Such systems are subjected to biaxial loading, which can induce crack formation and propagation, ultimately leading to catastrophic mechanical failure. In this study, the mechanical and tribological behaviour of AAO, prepared from two different types of electrolytes (sulphuric and oxalic acids), are studied in detail. The electrolytic conditions are adjusted to render highly tuneable average pore diameters (between 16 and 75 nm), with porosity levels ranging from 9% to 65%. Well-ordered porous AAO are produced by two-step anodization at rather low temperatures. Mechanical properties, mainly hardness and Young's modulus, are investigated using nanoindentation. Both the porosity degree and the composition of the electrolytic baths used to prepare the AAO have an influence on the mechanical properties. Ball-on-flat configuration was used to estimate the tribological behaviour under dry conditions. No major cracks were observed by scanning electron microscopy, neither after indentation or fretting tests. In the running-in period of tribology experiments the pores were filled with debris. This was followed by the formation of a highly adherent tribolayer – a third body consisting of fine worn particles originated from both the sample and the counterbody. Pore diameter and porosity percentage are found to strongly affect hardness and Young's modulus, but they do not have a major effect on the frictional behaviour. - Highlights: • Well-ordered porous AAO with pore diameters between 16 and 75 nm were produced. • Porosity and composition of electrolytic baths influence the mechanical properties. • Ball-on-flat configuration was used in tribological testing under dry conditions. • Adherent tribolayer consisting of fine worn particles prevents AAO from cracking. • Testing parameters are moreover essential

The sectional size effect on the deformation behaviour of Inconel 718 at different temperatures

Directory of Open Access Journals (Sweden)

Zhao R.

2015-01-01

Full Text Available Inconel 718, as a multiphase super-alloy, is widely used in aeronautics and astronautics industries. In this field, a modified Hall-Petch equation was used to describe the grain size effect on the deformation behaviour of Inconel 718 sheet in uniaxial tension test. There is a piecewise linearity in the σ-d−1 curve: With the thickness t is a constant, the slope changes obviously after a critical t/d ratio, which increases with strain. Moreover, the influence on sectional curve caused by temperature is also an interesting issue. To address that, the sectionalized curve was fitted at different strains and temperatures, and the phenomena of grain size effect in piecewise curve at different temperatures were further explained. A surface model of Inconel 718 was proposed to explain the intrinsic mechanism of different slopes. The research provided an in-depth understanding of the size effect on the deformation behaviour of Inconel 718 at different hot working temperatures.

Mechanical behaviour of a creased thin strip

Directory of Open Access Journals (Sweden)

J. Liu

2018-02-01

Full Text Available In this study the mechanical behaviour of a creased thin strip under opposite-sense bending was investigated. It was found that a simple crease, which led to the increase of the second moment of area, could significantly alter the overall mechanical behaviour of a thin strip, for example the peak moment could be increased by 100 times. The crease was treated as a cylindrical segment of a small radius. Parametric studies demonstrated that the geometry of the strip could strongly influence its flexural behaviour. We showed that the uniform thickness and the radius of the creased segment had the greatest and the least influence on the mechanical behaviour, respectively. We further revealed that material properties could dramatically affect the overall mechanical behaviour of the creased strip by gradually changing the material from being linear elastic to elastic-perfect plastic. After the formation of the fold, the moment of the two ends of the strip differed considerably when the elasto-plastic materials were used, especially for materials with smaller tangent modulus in the plastic range. The deformation patterns of the thin strips from the finite element simulations were verified by physical models made of thin metal strips. The findings from this study provide useful information for designing origami structures for engineering applications using creased thin strips.

Concrete for PCRV's: Mechanical properties at elevated temperatures and residual mechanical behaviour after triaxial preloading

International Nuclear Information System (INIS)

Aschl, H.; Moosecker, W.

1979-01-01

During the lifetime of reactor vessels stress states will change as a result of changes in loading and heating, shrinkage and creep. For the design of prestressed concrete reactor vessels information is required about the behaviour of concrete under multiaxial short- and long-term loading at elevated temperatures. Therefore, tests were carried out at the Institut fuer Massivbau of the Technical University of Munich to study the properties of mass concrete under uniaxial loading at 353 K. Additionally, biaxial creep of concrete up to 368 K was investigated. Some of the uniaxial test specimens were sealed with a copper foil to avoid drying. The concrete contained calzite gravel. The thermal expansion coefficient of predried concrete was 9.5 x 10 -6 , of sealed concrete 13.6 x 10 -6 and of unsealed concrete 13.2 x 10 -6 . The modulus of elasticity at 353 K (393 K) was reduced by 10 (13)% for sealed and by 15 (22)% for unsealed specimens. Total shrinkage deformations of heated concrete were 190 to 225 microstrains for sealed and 250 to 350 microstrains for unsealed specimens. Creep deformations were highly dependent upon temperature being about 3 times higher at 353 K for sealed and unsealed concrete. (orig.)

Behavioural ratings of self-regulatory mechanisms and driving behaviour after an acquired brain injury.

Science.gov (United States)

Rike, Per-Ola; Ulleberg, Pål; Schultheis, Maria T; Lundqvist, Anna; Schanke, Anne-Kristine

2014-01-01

To explore whether measurements of self-regulatory mechanisms and cognition predict driving behaviour after an acquired brain injury (ABI). Consecutive follow-up study. At baseline participants included 77 persons with stroke and 32 persons with a traumatic brain injury (TBI), all of whom completed a multidisciplinary driving assessment (MDA). A follow-up cohort of 34 persons that succeeded the MDA was included. Baseline measurements: Neuropsychological tests and measurements of self-regulatory mechanisms (BRIEF-A and UPPS Impulsive Behaviour Scale), driving behaviour (DBQ) and pre-injury driving characteristics (mileage, compensatory driving strategies and accident rates). Follow-up measurements: Post-injury driving characteristics were collected by mailed questionnaires from the participants who succeeded the MDA. A MDA, which included a medical examination, neuropsychological testing and an on-road driving test, was considered in the decision for or against granting a driver's license. Self-regulatory mechanisms and driving behaviour were examined for research purposes only. At baseline, self-regulatory mechanisms were significantly associated to aberrant driving behaviour, but not with neuropsychological data or with the outcome of the on-road driving test. Aspects of self-regulation were associated to driving behaviour at follow-up. It is recommended that self-regulatory measurements should regularly be considered in the driving assessments after ABI.

Influence of phase transformations on the mechanical behaviour of refractory ceramics at high temperature

International Nuclear Information System (INIS)

Schmitt, N.; Poirier, J.

2009-01-01

Refractories used at high temperature are subjected to high chemical and mechanical stresses. The mastery of their microstructure as well as the phase changes occurring in service is essential to ensure resistance to wear and failure of refractory linings. Great progress has been made: combining efficient techniques for the investigation of the microstructure with powerful numerical tools (thermochemical and thermo-mechanical computations) provides information (e.g., degradation mechanisms) that cannot be obtained directly. Also multi-physical and multi-scale models developing materials with high-performance for higher temperature and with longer lifetime. In this paper, through several examples we show some interactions between the mechanical behavior and the microstructure transformations of refractory ceramics. The tools developed to characterize their microstructure change in situ (e.g., at high temperature) and to identify their kinetics are described. Some methodologies and tools developed in recent years, today, provide a better understanding of in-service behavior of refractories while identifying the critical material and process parameters likely to increase life-time. (authors)

Mechanical behaviour of nanoparticles: Elasticity and plastic ...

Indian Academy of Sciences (India)

2015-06-03

Jun 3, 2015 ... Mechanical behaviour of nanoparticles: Elasticity and plastic deformation mechanisms ... The main results in terms of elasticity and plastic deformation mechanisms are then reported ... Pramana – Journal of Physics | News.

Multi-scale modelling of the physicochemical-mechanical coupling of fuel behaviour at high temperature in pressurized water reactors

International Nuclear Information System (INIS)

Julien, Jerome

2008-01-01

Within the frame of the problematic of pellet-sheath interaction in a nuclear fuel rod, a good description of the fuel thermo-mechanical behaviour is required. This research thesis reports the coupling of physics-chemistry (simulation of gas transfers between different cavities) and mechanics (assessment of fuel viscoplastic strains). A new micromechanical model is developed which uses a multi-scale approach to describe the evolution of the double population of cavities (cavities with two different scales) while taking internal pressures as well as the fuel macroscopic viscoplastic behaviour into account. The author finally describes how to couple this micromechanical mode to physics-chemistry models [fr

Mechanical behaviour of PWR fuel rods during intermediate storage

International Nuclear Information System (INIS)

Bouffioux, P.; Dalmas, R.; Bernaudat, C.

2000-01-01

EDF, which owns the irradiated fuel coming from its NPPs, has initiated studies regarding the mechanical behaviour of a fuel rod and the integrity of its cladding, in the case where the spent fuel is stored for a significant duration. During the phases following in-reactor irradiation (ageing in a water-pool, transport and intermediate storage), many phenomena, which are strongly coupled, may influence the cladding integrity: - residual power and temperature decay; - helium production and release in the free volume of the rod (especially for MOX fuel); - fuel column swelling; - cladding creep-out under the inner gas pressure of the fuel rod; - metallurgical changes due to high temperatures during transportation. In parallel, the quantification of the radiological risk is based on the definition of a cladding integrity criterion. Up to now, this criterion requires that the clad hoop strain due to creep-out does not exceed 1%. A more accurate criterion is being investigated. The study and modelling of all the phenomena mentioned above are included in a R and D programme. This programme also aims at redefining the cladding integrity criterion, which is assumed to be too conservative. The R and D programme will be presented. In order to predict the overall behaviour of the rod during the intermediate storage phases, the AVACYC code has been developed. It includes the models developed in the R and D programme. The input data of the AVACYC code are provided by the results of in-reactor rod behaviour simulations, using the thermal-mechanical CYRANO3 code. Its main results are the evolution vs. time of hoop stresses in the cladding, rod internal pressure and cladding hoop strains. Chained CYRANO-AVACYC calculations have been used to simulate the behaviour of MOX fuel rods irradiated up to 40 GWd/t and stored under air during 100 years, or under water during 50 years. For such fuels, where the residual power remains high, we show that a large part of the cladding strain

Thermo-hydro-mechanical behaviour of Boom clay; Comportement thermo-hydro-mecanique de l'argile de Boom

Energy Technology Data Exchange (ETDEWEB)

Le, T.T

2008-01-15

This thesis studied the thermo-hydro-mechanical properties of Boom clay, which was chosen to be the host material for the radioactive waste disposal in Mol, Belgium. Firstly, the research was concentrated on the soil water retention properties and the hydro-mechanical coupling by carrying out axial compression tests with suction monitoring. The results obtained permitted elaborating a rational experimental procedure for triaxial tests. Secondly, the systems for high pressure triaxial test at controlled temperature were developed to carry out compression, heating, and shearing tests at different temperatures. The obtained results showed clear visco-elasto-plastic behaviour of the soil. This behaviour was modelled by extending the thermo-elasto-plastic model of Cui et al. (2000) to creep effect. (author)

Effects of temperature changes and stress loading on the mechanical and shape memory properties of thermoplastic materials with different glass transition behaviours and crystal structures.

Science.gov (United States)

Iijima, Masahiro; Kohda, Naohisa; Kawaguchi, Kyotaro; Muguruma, Takeshi; Ohta, Mitsuru; Naganishi, Atsuko; Murakami, Takashi; Mizoguchi, Itaru

2015-12-01

To investigate the effects of temperature changes and stress loading on the mechanical and shape memory properties of thermoplastic materials with different glass transition behaviours and crystal structures. Five thermoplastic materials, polyethylene terephthalate glycol (Duran®, Scheu Dental), polypropylene (Hardcast®, Scheu Dental), and polyurethane (SMP MM®, SMP Technologies) with three different glass transition temperatures (T g) were selected. The T g and crystal structure were assessed using differential scanning calorimetry and X-ray diffraction. The deterioration of mechanical properties by thermal cycling and the orthodontic forces during stepwise temperature changes were investigated using nanoindentation testing and custom-made force-measuring system. The mechanical properties were also evaluated by three-point bending tests; shape recovery with heating was then investigated. The mechanical properties for each material were decreased significantly by 2500 cycles and great decrease was observed for Hardcast (crystal plastic) with higher T g (155.5°C) and PU 1 (crystalline or semi-crystalline plastic) with lower T g (29.6°C). The Duran, PU 2, and PU 3 with intermediate T g (75.3°C for Duran, 56.5°C for PU 2, and 80.7°C for PU 3) showed relatively stable mechanical properties with thermal cycling. The polyurethane polymers showed perfect shape memory effect within the range of intraoral temperature changes. The orthodontic force produced by thermoplastic appliances decreased with the stepwise temperature change for all materials. Orthodontic forces delivered by thermoplastic appliances may influence by the T g of the materials, but not the crystal structure. Polyurethane is attractive thermoplastic materials due to their unique shape memory phenomenon, but stress relaxation with temperature changes is expected. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For

Mechanical behaviour of Br0.5Sr0.5Co0.8Fe0.2O3-δ under uniaxial compression

International Nuclear Information System (INIS)

Araki, Wakako; Malzbender, Jürgen

2013-01-01

The present study reports on the mechanical behaviour of Br 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3-δ under uniaxial compression at various temperatures. The stress–strain curve at room temperature shows a small but clear creep deformation, along with a hysteresis and a remnant strain, which could be related to a spin transition of cobalt. The hysteresis as well as Young’s modulus decrease with increasing temperature to 473 K, at which temperature the creep behaviour disappears. The material shows conventional high-temperature creep above 673 K

Corrosion behaviour of high temperature alloys in the cooling gas of high temperature reactors

International Nuclear Information System (INIS)

Quadakkers, W.J.; Schuster, H.

1989-01-01

The reactive impurities in the primary cooling helium of advanced high temperature gas cooled reactors (HTGR) can cause oxidation, carburization or decarburization of the heat exchanging metallic components. By studies of the fundamental aspects of the corrosion mechanisms it became possible to define operating conditions under which the metallic construction materials show, from the viewpoint of technical application, acceptable corrosion behaviour. By extensive test programmes with exposure times of up to 30,000 hours, a data base has been obtained which allows a reliable extrapolation of the corrosion effects up to the envisaged service lives of the heat exchanging components. (author). 6 refs, 7 figs

Low temperature behaviour of elastomers in seals; Tieftemperaturverhalten von Elastomeren im Dichtungseinsatz

Energy Technology Data Exchange (ETDEWEB)

Jaunich, Matthias

2012-04-25

Elastomeric seals are of high importance as machine parts and construction elements, but in spite of this the low temperature limit for the use of a seal was not fully understood. Hence, the required safety relevant evaluation of the lowest acceptable operating seal temperature is difficult. Therefore the presented work was aimed to understand the temperature dependent material behaviour of representative elastomers and to conclude from this knowledge the low temperature limit down to which such seals could safely fulfil the desired requirements. Starting with the published statement that a seal can safely work below its glass transition temperature the influence of the glass-rubber-transition was investigated. At first the glass-rubber-transition temperatures of the selected elastomers were determined applying several techniques to allow a comparison with the behaviour of the seals during component tests. Furthermore a new method to characterise the low temperature behaviour of elastomers was developed that emulates the key features of the standardised compression set test used for seal materials. In comparison to the standardized test this new method allows a much faster measurement that can be automatically performed. Using a model based data analysis an extrapolation of the results to different temperatures can be performed and therefore the necessary measuring expenditure can be additionally reduced. For the temperature dependent characterisation of the failure process of real seals a measurement setup was designed and the materials behaviour was investigated. By use of the results of all applied characterisation techniques the observed dependence of the failure temperature on the degree of compression could be explained for the investigated seals under static load. Additionally information about the behaviour of such seals under dynamic load could be gained from the time dependent material behaviour by use of the time temperature superposition relationship

Multi-scale modeling of the thermo-hydro- mechanical behaviour of heterogeneous materials. Application to cement-based materials under severe loads

International Nuclear Information System (INIS)

Grondin, Frederic Alain

2005-01-01

The work of modeling presented here relates to the study of the thermo-hydro- mechanical behaviour of porous materials based on hydraulic binder such as concrete, High Performance Concrete or more generally cement-based materials. This work is based on the exploitation of the Digital Concrete model, of the finite element code Symphonie developed in the Scientific and Technical Centre for Building (CSTB), in coupling with the homogenization methods to obtain macroscopic behaviour laws drawn from the Micro-Macro relations. Scales of investigation, macroscopic and microscopic, has been exploited by simulation in order to allow the comprehension fine of the behaviour of cement-based materials according to thermal, hydrous and mechanical loads. It appears necessary to take into account various scales of modeling. In order to study the behaviour of the structure, we are brought to reduce the scale of investigation to study the material more particularly. The research tasks presented suggest a new approach for the identification of the multi-physic behaviour of materials by simulation. In complement of the purely experimental approach, based on observations on the sample with measurements of the apparent parameters on the macroscopic scale, this new approach allows to obtain the fine analysis of elementary mechanisms in acting within the material. These elementary mechanisms are at the origin of the evolution of the macroscopic parameters measured in experimental tests. In this work, coefficients of the thermo-hydro-mechanical behaviour law of porous materials and the equivalent hydraulic conductivity were obtained by a multi-scales approach. Applications has been carried out on the study of the damaged behaviour of cement-based materials, in the objective to determine the elasticity tensor and the permeability tensor of a High Performance Concrete at high temperatures under a mechanical load. Also, the study of the strain evolution of cement-based materials at low

Understanding and modelling of the aniso-thermal cyclic mechanical behaviour of the AISI 316LN austenitic stainless steel

International Nuclear Information System (INIS)

Gentet, D.

2009-11-01

The main subject of this report consists in proposing a mechanical model of the viscoplastic behaviour of an austenitic stainless steel under isothermal and aniso-thermal low cycle fatigue loadings at high temperatures (550-900 K). In this domain, numerous phenomena linked to dynamic strain ageing (DSA) and to dipolar dislocation structure formation may appear. Isothermal and aniso-thermal low cycle fatigue tension-compression tests were performed in order to verify some aspects about the effect of temperature on the mechanical behaviour. The study of the hysteresis loops and the observation of dislocation structures carried on transmission electron microscopy establish two different DSA mechanisms during isothermal tests. The effect of temperature history is shown for for particular temperature sequences. It is demonstrated that the stress amplitude increase when the sample is submitted to cycles at 'high temperature' is linked to the second mechanism of DSA. It comes from the increase of short range interaction between dislocations (chromium segregation), but it is also the consequence of the lack of dipolar structure annihilation at low temperature. From the experimental analysis of DSA mechanisms and dipolar restoration, a macroscopic aniso-thermal model is developed using physical internal variables (densities of dislocations). The equations of a polycrystalline model are rewritten with the aim of getting a simple multi-scale approach which can be used on finite elements analysis software. Between 550 and 873 K, the simulation results are in good accordance with the macroscopic and microscopic observations of low cycle fatigue, relaxation, and 2D-ratchetting tests. (author)

High temperature flow behaviour of SiC reinforced lithium

Indian Academy of Sciences (India)

The compressive flow behaviour of lithium aluminosilicate (LAS) glass, with and without SiC particulate reinforcements, was studied. The LAS glass crystallized to spodumene during high-temperature testing. The flow behaviour of LAS glass changed from Newtonian to non-Newtonian due to the presence of crystalline ...

Mechanical Behaviour of the LHC Cryodipoles

CERN Document Server

Buenaventura, A; Skoczen, Blazej

2000-01-01

The LHC cryodipoles are slender and heavy objects more than 15-m long. The major components of the cryodipole assembly are the 28-tonne cold mass, supported on its three Glass-Fibre-Reinforced-Epoxy support posts and the 4-tonne vacuum vessel. The performance of the LHC depends very much upon the accurate positioning of the dipoles and the beam tubes, in particular to maximise the useful beam apertures. The cryodipoles will be conditioned and measured in surface assembly buildings, then handled and transported to their positions in the tunnel and, finally, aligned. This paper presents the static and dynamic studies of the cryodipole in different configurations. The tests and analyses carried out have led to a thorough understanding of the mechanical behaviour of the cryodipoles. From the static analysis, an hyperstatic supporting system is proposed in order to minimise the systematic deflections and the effects due to changing temperature conditions in the tunnel. The dynamic analysis has shown that the cryod...

High-Temperature Creep Behaviour and Positive Effect on Straightening Deformation of Q345c Continuous Casting Slab

Science.gov (United States)

Guo, Long; Zhang, Xingzhong

2018-03-01

Mechanical and creep properties of Q345c continuous casting slab subjected to uniaxial tensile tests at high temperature were considered in this paper. The minimum creep strain rate and creep rupture life equations whose parameters are calculated by inverse-estimation using the regression analysis were derived based on experimental data. The minimum creep strain rate under constant stress increases with the increase of the temperature from 1000 °C to 1200 °C. A new casting machine curve with the aim of fully using high-temperature creep behaviour is proposed in this paper. The basic arc segment is cancelled in the new curve so that length of the straightening area can be extended and time of creep behaviour can be increased significantly. For the new casting machine curve, the maximum straightening strain rate at the slab surface is less than the minimum creep strain rate. So slab straightening deformation based on the steel creep behaviour at high temperature can be carried out in the process of Q345c steel continuous casting. The effect of creep property at high temperature on slab straightening deformation is positive. It is helpful for the design of new casting machine and improvement of old casting machine.

Near-threshold fatigue crack behaviour in EUROFER 97 at different temperatures

Science.gov (United States)

Aktaa, J.; Lerch, M.

2006-07-01

The fatigue crack behaviour in EUROFER 97 was investigated at room temperature (RT), 300, 500 and 550 °C for the assessment of cracks in first wall structures built from EUROFER 97 of future fusion reactors. For this purpose, fatigue crack growth tests were performed using CT specimens with two R-ratios, R = 0.1 and R = 0.5 ( R is the load ratio with R = Fmin/ Fmax where Fmin and Fmax are the minimum and maximum applied loads within a cycle, respectively). Hence, fatigue crack threshold, fatigue crack growth behaviour in the near-threshold range and their dependences on temperature and R-ratio were determined and described using an analytical formula. The fatigue crack threshold showed a monotonous dependence on temperature which is for R = 0.5 insignificantly small. The fatigue crack growth behaviour exhibited for R = 0.1 a non-monotonous dependence on temperature which is explained by the decrease of yield stress and the increase of creep damage with increasing temperature.

High temperature oxidation behaviour of mullite coated C/C composites in air

International Nuclear Information System (INIS)

Fritze, H.; Borchardt, G.; Weber, S.; Scherrer, S.; Weiss, R.

1997-01-01

Based on thermogravimetric measurements on Si-SiC-mullite coated C/C material the temperature dependence of the overall rate constant is interpreted in the temperature range 400 C 1400 C), however, the oxidation behaviour of SiC limits long term application. In this temperature range, additional outer mullite coatings produced by pulsed laser deposition improve the oxidation behaviour. (orig.)

Modeling the effects of fast-neutron irradiation on the subsequent mechanical behaviour of type 316 stainless steel

International Nuclear Information System (INIS)

Dimelfi, R.J.; Kramer, J.M.

1980-01-01

A model describing the subsequent mechanical behaviour of type 316 stainless steel exposed to a fast reactor environment is presented. A constitutive law for the flow stress, based on the Voce equation, is introduced. The strain-rate and temperature-dependence of the flow stress is formulated in this equation; and it is assumed that all contributions to changes in the flow stress, at a given temperature and strain-rate, are manifested in a single hardness parameter. Physically-based models for work hardening, irradition hardening, and irradiation softening are presented. By combining the constitutive law with the relations describing the hardness, a system of equations is presented which describes the mechanical response of the material after specified neutron irradiation and thermal exposure. When the model is used to analyze flow stress data on unirradiated material as well as material irradiated over a wide range of fluence and temperature, agreement between predicted and observed behaviour is shown, supporting the assumption of a single flow law incorporating a single hardness parameter. (orig.)

Critical isothermal temperature and optimum mechanical behaviour of high Si-containing bainitic steels

International Nuclear Information System (INIS)

Misra, A.; Sharma, S.; Sangal, S.; Upadhyaya, A.; Mondal, K.

2012-01-01

The redistribution of carbon during partitioning between retained austenite and bainitic ferrite decides the stability of the retained austenite. The martensitic start temperature (M S ) based on the carbon enriched retained austenite is observed to be the deciding factor for the volume fraction of the constituent phases obtained on isothermal bainitic transformation. The volume fraction of the phases is also calculated on the basis of metastable equi-free energy (T 0 ) curve. A good agreement is found between experimentally and theoretically calculated fractions of the phases. The isothermal holding temperature and time, the fraction of phases based on initial carbon content of the steel and M S temperatures have a close relation with the optimum mechanical properties of bainitic steels.

Critical isothermal temperature and optimum mechanical behaviour of high Si-containing bainitic steels

Energy Technology Data Exchange (ETDEWEB)

Misra, A.; Sharma, S.; Sangal, S.; Upadhyaya, A. [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India); Mondal, K., E-mail: kallol@iitk.ac.in [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India)

2012-12-15

The redistribution of carbon during partitioning between retained austenite and bainitic ferrite decides the stability of the retained austenite. The martensitic start temperature (M{sub S}) based on the carbon enriched retained austenite is observed to be the deciding factor for the volume fraction of the constituent phases obtained on isothermal bainitic transformation. The volume fraction of the phases is also calculated on the basis of metastable equi-free energy (T{sub 0}) curve. A good agreement is found between experimentally and theoretically calculated fractions of the phases. The isothermal holding temperature and time, the fraction of phases based on initial carbon content of the steel and M{sub S} temperatures have a close relation with the optimum mechanical properties of bainitic steels.

Effect of different B contents on the mechanical properties and cyclic oxidation behaviour of β-NiAlDy coatings

International Nuclear Information System (INIS)

Jia, Fang; Peng, Hui; Zheng, Lei; Guo, Hongbo; Gong, Shengkai; Xu, Huibin

2015-01-01

Highlights: • Dy and B co-doping strategy was proposed to modify β-NiAl coatings. • Mechanical properties and cyclic oxidation behaviour of coatings were investigated. • The addition of boron improves the mechanical properties of β-NiAl coatings. • Cyclic oxidation behaviour of coatings is influenced by chemical reactions of boron. - Abstract: NiAlDy coatings doped with 0.05 at.% and 1.00 at.% B were produced by electron beam physical vapour deposition (EB-PVD). The mechanical properties and cyclic oxidation behaviour of the coatings were investigated. Compared to the undoped NiAlDy coating, the B doped coatings exhibited improved ductility, higher micro-hardness and elastic modulus. The NiAlDy alloys revealed similar thermal expansion behaviour in a temperature range of 200–1100 °C. However, the addition of B did not show significant improvement in the cyclic oxidation resistance of NiAlDy coatings, on the contrary, the addition of 1.00 at.% B accelerated the scale growth rate and aggravated the scale rumpling, which led to severe spallation. Related mechanisms were preliminarily discussed

Chemo-hydro-mechanical behaviour of unsaturated clays

International Nuclear Information System (INIS)

Mokni, N.; Olivella, S.; Alonso, E.E.; Romero, E.

2010-01-01

Document available in extended abstract form only. Understanding of the chemical effects on clays is essential for many problems ranging from pollution studies and waste-containment. Several studies examined the effect of changes in pore fluid composition on the mechanical and hydraulic properties. Volume changes (contraction/ expansion) have been measured on clay specimens upon exposure to salt solutions or permeation with organic liquids. Moreover, it was shown that permeation of clay with brine induces an increase of the shear strength. In addition, several models have been proposed to describe the chemo-mechanical behaviour of saturated clays under saturated conditions. A new chemo-hydro-mechanical model for unsaturated clays is under development. The chemo-mechanical effects are described within an elasto-plastic framework using the concept that chemical effects act on the plastic properties by increasing or decreasing the pre-consolidation stress. The model is based on the distinction within the material of a microstructural and a macro-structural levels. Chemical loading has a significant effect on the microstructure. The negative pressure associated with the capillary water plays its role in the interconnected macro pores. By adopting simple assumptions concerning the coupling between the two levels it is intended to reproduce the features of the behaviour of unsaturated clays when there is a change in pore fluid composition (increase or decrease of concentration). A yield surface which defines the set of yield pre-consolidation stress values, for each associated capillary suction and concentration of pore fluid should be defined. In addition, the behaviour of clays under unsaturated condition and the behaviour at full saturation under chemical loading represent two limiting cases of the framework. Studies on the compatibility of Boom Clay with large amounts of nitrate- bearing bituminized radioactive waste have recently raised a particular interest on the

Mechanical behaviour of Nd:YAG laser welded superelastic NiTi

International Nuclear Information System (INIS)

Vieira, L. Alberty; Fernandes, F.M. Braz; Miranda, R.M.; Silva, R.J.C.; Quintino, L.; Cuesta, A.; Ocana, J.L.

2011-01-01

Highlights: → The main innovations claimed are: understand rolling direction effect on mechanical cycling of laser welded NiTi. → Functionality confirmed by stabilization of hysteretic response up to 8% strain. → Welds tensile cycled exhibited superior functional mechanical behaviour. → For applied stresses of 50 MPa below UTS the joints showed superelastic behaviour. - Abstract: Joining techniques for shape memory alloys (SMA) has become of great interest, as their functional properties, namely shape memory effect (SME) and superelasticity (SE), present unique solutions for state-of-the-art applications, although limited results concerning mechanical properties are reported. This paper reports experimental work performed with Nd:YAG continuous wave laser welding of superelastic cold-rolled plates of NiTi 1 mm thick. The mechanical behaviour was evaluated by means of tensile tests performed both to failure and to cycling. The superelastic behaviour of the welded joints was observed for applied stresses close to about 50 MPa below the ultimate tensile strength of the welds. The functionality was confirmed by analyzing the stabilization of the mechanical hysteretic response to strain levels up to 8%. For tensile cycling involving strain levels larger than 6%, welded specimens were found to exhibit superior functional mechanical behaviour presenting larger recoverable strain levels. The fracture surfaces were observed by scanning electron microscopy (SEM) and the effect of the rolling direction on mechanical properties was evaluated and discussed, reinforcing the importance of joint design when laser welding these alloys.

The impact of high temperatures on foraging behaviour and body ...

African Journals Online (AJOL)

High temperatures can pose significant thermoregulation challenges for endotherms, and determining how individual species respond to high temperatures will be important for predicting the impact of global warming on wild populations. Animals can adjust their behaviour or physiology to cope with higher temperatures, ...

Near-threshold fatigue crack behaviour in EUROFER 97 at different temperatures

International Nuclear Information System (INIS)

Aktaa, J.; Lerch, M.

2006-01-01

The fatigue crack behaviour in EUROFER 97 was investigated at room temperature (RT), 300, 500 and 550 deg. C for the assessment of cracks in first wall structures built from EUROFER 97 of future fusion reactors. For this purpose, fatigue crack growth tests were performed using CT specimens with two R-ratios, R = 0.1 and R = 0.5 (R is the load ratio with R = F min /F max where F min and F max are the minimum and maximum applied loads within a cycle, respectively). Hence, fatigue crack threshold, fatigue crack growth behaviour in the near-threshold range and their dependences on temperature and R-ratio were determined and described using an analytical formula. The fatigue crack threshold showed a monotonous dependence on temperature which is for R = 0.5 insignificantly small. The fatigue crack growth behaviour exhibited for R = 0.1 a non-monotonous dependence on temperature which is explained by the decrease of yield stress and the increase of creep damage with increasing temperature

Influence of Temperature on AA6014 Alloy Tribological Behaviour in Stamping Operations

International Nuclear Information System (INIS)

Sgarabotto, F.; Ghiotti, A.; Bruschi, S.

2011-01-01

The evaluation of the tribological characteristics at the metal blank-tool interface during sheet metal working operations is usually carried out by accurately reproducing the mechanical and kinematical parameters occurring during the real process. The high rate production characterizing the industrial processes can induce significant temperature increase in both the blank and the dies during deformation. With respect to this aspect, among the other process conditions, an accurate tribological characterization should take into account the influence of the temperature variations at the blank and the dies. In the present paper, a novel apparatus to investigate the tribological conditions during sheet metal working processes is presented. In addition to the control of mechanical (i.e. normal pressure) and kinematic parameters (i.e. sliding speed, sliding length), the developed testing machine permits to reproduce the thermal fields and monitor the thermal conditions of the sheet and tool materials. Experiments were carried out on aluminium alloy sheets between 20 deg. and 200thinsp; deg. C by using both coated and uncoated dies. It is proved that the temperature influences the tribological behaviour, especially when coated dies are utilized.

Effect of hot isostatic pressing temperature on the microstructural and mechanical properties in the mullite-zirconia composites

International Nuclear Information System (INIS)

Greca, M.C.G.; Melo, M. de F.

1990-01-01

This work studies the densification, the microstrutural evolution (porosity and zirconia grain size) and bending strength (σ f ) of the two mullite-zirconia composites with TiO 2 additions (0.25 and 1,0 mole%) submitted to different kind of hipping cycles at several temperatures. The results have been shown that: i) HIPing temperature seem to have no influence in densification and mechanical behaviour. ii) Total densification only appears in composition with more quantity of titania (1.0 mole%) which prove that titanium enhance the mass transfer by changes in grain boundary microchemistry. iii) Mechanical behaviour is correlated with densification and microstructural evolution for both composites and degradation is present at 1500 0 C and 1550 0 C which is related with particle coarsening. (author) [pt

Mechanical Behaviour of 304 Austenitic Stainless Steel Processed by Room Temperature Rolling

Science.gov (United States)

Singh, Rahul; Goel, Sunkulp; Verma, Raviraj; Jayaganthan, R.; Kumar, Abhishek

2018-03-01

To study the effect of room temperature rolling on mechanical properties of 304 Austenitic Stainless Steel, the as received 304 ASS was rolled at room temperature for different percentage of plastic deformation (i.e. 30, 50, 70 and 90 %). Microstructural study, tensile and hardness tests were performed in accordance with ASTM standards to study the effect of rolling. The ultimate tensile strength (UTS) and hardness of a rolled specimen have enhanced with rolling. The UTS has increased from 693 MPa (as received) to 1700 MPa (after 90% deformation). The improvement in UTS of processed samples is due to combined effect of grain refinement and stress induced martensitic phase transformation. The hardness values also increases from 206 VHN (as received) to 499 VHN (after 90% deformation). Magnetic measurements were also conducted to confirm the formation of martensitic phase.

Influence of strain rate and temperature on tensile properties and flow behaviour of a reduced activation ferritic-martensitic steel

Energy Technology Data Exchange (ETDEWEB)

Vanaja, J., E-mail: jvanaja4@gmail.com [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Laha, K. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Sam, Shiju [Institute for Plasma Research, Gandhinagar, Gujarat (India); Nandagopal, M.; Panneer Selvi, S.; Mathew, M.D.; Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Rajendra Kumar, E. [Institute for Plasma Research, Gandhinagar, Gujarat (India)

2012-05-15

Tensile strength and flow behaviour of a Reduced Activation Ferritic-Martensitic (RAFM) steel (9Cr-1W-0.06Ta-0.22V-0.08C) have been investigated over a temperature range of 300-873 K at different strain rates. Tensile strength of the steel decreased with temperature and increased with strain rate except at intermediate temperatures. Negative strain rate sensitivity of flow stress of the steel at intermediate temperatures revealed the occurrence of dynamic strain ageing in the steel, even though no serrated flow was observed. The tensile flow behaviour of the material was well represented by the Voce strain hardening equation for all the test conditions. Temperature and strain rate dependence of the various parameters of Voce equation were interpreted with the possible deformation mechanisms. The equivalence between the saturation stress at a given strain rate in tensile test and steady state deformation rate at a given stress in creep test was found to be satisfied by the RAFM steel.

Influence of strain rate and temperature on tensile properties and flow behaviour of a reduced activation ferritic-martensitic steel

Science.gov (United States)

Vanaja, J.; Laha, K.; Sam, Shiju; Nandagopal, M.; Panneer Selvi, S.; Mathew, M. D.; Jayakumar, T.; Rajendra Kumar, E.

2012-05-01

Tensile strength and flow behaviour of a Reduced Activation Ferritic-Martensitic (RAFM) steel (9Cr-1W-0.06Ta-0.22V-0.08C) have been investigated over a temperature range of 300-873 K at different strain rates. Tensile strength of the steel decreased with temperature and increased with strain rate except at intermediate temperatures. Negative strain rate sensitivity of flow stress of the steel at intermediate temperatures revealed the occurrence of dynamic strain ageing in the steel, even though no serrated flow was observed. The tensile flow behaviour of the material was well represented by the Voce strain hardening equation for all the test conditions. Temperature and strain rate dependence of the various parameters of Voce equation were interpreted with the possible deformation mechanisms. The equivalence between the saturation stress at a given strain rate in tensile test and steady state deformation rate at a given stress in creep test was found to be satisfied by the RAFM steel.

Influence of strain rate and temperature on tensile properties and flow behaviour of a reduced activation ferritic–martensitic steel

International Nuclear Information System (INIS)

Vanaja, J.; Laha, K.; Sam, Shiju; Nandagopal, M.; Panneer Selvi, S.; Mathew, M.D.; Jayakumar, T.; Rajendra Kumar, E.

2012-01-01

Tensile strength and flow behaviour of a Reduced Activation Ferritic–Martensitic (RAFM) steel (9Cr–1W–0.06Ta–0.22V–0.08C) have been investigated over a temperature range of 300–873 K at different strain rates. Tensile strength of the steel decreased with temperature and increased with strain rate except at intermediate temperatures. Negative strain rate sensitivity of flow stress of the steel at intermediate temperatures revealed the occurrence of dynamic strain ageing in the steel, even though no serrated flow was observed. The tensile flow behaviour of the material was well represented by the Voce strain hardening equation for all the test conditions. Temperature and strain rate dependence of the various parameters of Voce equation were interpreted with the possible deformation mechanisms. The equivalence between the saturation stress at a given strain rate in tensile test and steady state deformation rate at a given stress in creep test was found to be satisfied by the RAFM steel.

Tensile behaviour of natural fibres. Effect of loading rate, temperature and humidity on the “accommodation” phenomena

Directory of Open Access Journals (Sweden)

Placet V.

2010-06-01

Full Text Available The use of natural fibres in high performance composite requires an accurate understanding of the mechanical behaviour of the fibres themselves. As for all biobased materials, the mechanical properties of natural fibres depend generally on the testing rate and on the environmental conditions. In addition, natural fibres as hemp for example exhibit a particular mechanism of stiffness increase and accommodation phenomena under cyclic loading. Loading rate, temperature and humidity effects on the viscoelastic properties of hemp fibres were investigated in this work. The collected results clearly emphasis the involvement of time-dependant and mechano-sorptive mechanisms.

Mitigation of climate change impacts on raptors by behavioural adaptation: ecological buffering mechanisms

Science.gov (United States)

Wichmann, Matthias C.; Groeneveld, Jürgen; Jeltsch, Florian; Grimm, Volker

2005-07-01

The predicted climate change causes deep concerns on the effects of increasing temperatures and changing precipitation patterns on species viability and, in turn, on biodiversity. Models of Population Viability Analysis (PVA) provide a powerful tool to assess the risk of species extinction. However, most PVA models do not take into account the potential effects of behavioural adaptations. Organisms might adapt to new environmental situations and thereby mitigate negative effects of climate change. To demonstrate such mitigation effects, we use an existing PVA model describing a population of the tawny eagle ( Aquila rapax) in the southern Kalahari. This model does not include behavioural adaptations. We develop a new model by assuming that the birds enlarge their average territory size to compensate for lower amounts of precipitation. Here, we found the predicted increase in risk of extinction due to climate change to be much lower than in the original model. However, this "buffering" of climate change by behavioural adaptation is not very effective in coping with increasing interannual variances. We refer to further examples of ecological "buffering mechanisms" from the literature and argue that possible buffering mechanisms should be given due consideration when the effects of climate change on biodiversity are to be predicted.

Mechanical behaviour of composite materials made by resin film infusion

Directory of Open Access Journals (Sweden)

Casavola C.

2010-06-01

Full Text Available Innovative composite materials are frequently used in designing aerospace, naval and automotive components. In the typical structure of composites, multiple layers are stacked together with a particular sequence in order to give specific mechanical properties. Layers are organized with different angles, different sequences and different technological process to obtain a new and innovative material. From the standpoint of engineering designer it is useful to consider the single layer of composite as macroscopically homogeneous material. However, composites are non homogeneous bodies. Moreover, layers are not often perfectly bonded together and delamination often occurs. Other violations of lamination theory hypotheses, such as plane stress and thin material, are not unusual and in many cases the transverse shear flexibility and the thickness-normal stiffness should be considered. Therefore the real behaviour of composite materials is quite different from the predictions coming from the traditional lamination theory. Due to the increasing structural performance required to innovative composites, the knowledge of the mechanical properties for different loading cases is a fundamental source of concern. Experimental characterization of materials and structures in different environmental conditions is extremely important to understand the mechanical behaviour of these new materials. The purpose of the present work is to characterize a composite material developed for aerospace applications and produced by means of the resin film infusion process (RFI. Different tests have been carried out: tensile, open-hole and filled-hole tensile, compressive, openhole and filled-hole compressive. The experimental campaign has the aim to define mechanical characteristics of this RFI composite material in different conditions: environmental temperature, Hot/Wet and Cold.

Several aspects of the temperature history in relation to the cyclic behaviour of an austenitic stainless steel

International Nuclear Information System (INIS)

Gentet, D.; Feaugas, X.; Risbet, M.; Lejeail, Y.; Pilvin, P.

2011-01-01

Highlights: · Dynamic strain ageing consequences on the temperature history memorization effect. · Temperature is mainly focused at a temperature range equal to 293-923 K. · Two peaks are observed on the curve describing saturation stress amplitude. · Cyclic behaviour is a function of the temperature range explored. · Cyclic temperature history is mainly associated with chromium segregation. - Abstract: A consistent mechanical and transmission electron microscopy (TEM) database is proposed to discuss the consequences of dynamic strain ageing (DSA) on the temperature history memory effect observed under the cyclic loading of a 316LN austenitic stainless steel. Two DSA mechanisms have been identified in relation with two temperature regimes: the first of which may be related to the Suzuki effect (in the low temperature regime) and the second is linked to solute segregation at dislocation node (in the high temperature regime). The temperature history memory effect is a function of the temperature range and can be explained in terms of chromium segregation and the potentiality to obtain 'stability' in dipolar dislocation structures. Both aspects are discussed based on the measurement of internal stress changes.

Effect of heat treatment, with and without mechanical work, on the tensile and creep behaviour at 6000C of austenitic stainless steel stabilised with titanium

International Nuclear Information System (INIS)

Padilha, A.F.

1983-01-01

The effect of various heat treatments, with and without mechanical work, on the microstructure and the tensile and creep behaviour at 600 0 C of the titanium stabilised austenitic stainless steel DIN 1.4970, as well as the effects of aging temperature, pre-strain and small boron additions on the creep behaviour of these steels are discussed. The most probable mechanism is suggested. (Author) [pt

Microfracture behaviour of extruded Mg–Zn–Y alloys containing long-period stacking ordered structure at room and elevated temperatures

International Nuclear Information System (INIS)

Mine, Yoji; Yoshimura, Hajime; Matsuda, Mitsuhiro; Takashima, Kazuki; Kawamura, Yoshihito

2013-01-01

We studied the fracture behaviour of extruded Mg–Zn–Y alloys at room temperature (RT) and at 523 K using microfracture testing. An Mg 97 Zn 1 Y 2 alloy was used to obtain two-phase specimens consisting of α-Mg and long-period stacking ordered (LPSO) structure phases, and an Mg 88 Zn 5 Y 7 alloy was used to obtain specimens consisting of an LPSO phase. The microfracture testing of the two-phase specimen revealed that the fracture behaviour changed from brittle to ductile as the testing temperature increased. By contrast, the LPSO-phase specimen remained brittle even at the elevated temperature and the intrinsic fracture toughness values obtained at both testing temperatures were nearly identical. Ex situ transmission electron microscopy of the two-phase specimen showed that mechanical twinning in the α-Mg phase did not occur at the elevated temperature, although it was activated at RT. This suggests that the plastic deformation mode in the α-Mg phase plays a crucial part in the enhanced crack growth resistance of the two-phase alloy at the elevated temperature

Fatigue behaviour of the austenitic steel 1.4550 under mechanical and thermal cyclic loading

Energy Technology Data Exchange (ETDEWEB)

Siegele, D.; Fingerhuth, J.; Varfolomeev, I.; Moroz, S. [Fraunhofer Institute for Mechanics of Materials (IWM), Freiburg (Germany)

2014-07-01

Fatigue behaviour of the austenitic steel 1.4550 (X6CrNiNb18-10) under low-cycle fatigue and high-cycle thermal fatigue was investigated with in two research projects supported by the Federal Ministry of Economic Affairs and Energy and the Ministry of Education and Research. The objectives of the projects were the gain of deep understanding of the damage mechanisms under mechanical and thermal cyclic loading and the development of material models and simulation procedures for an improved lifetime assessment. In comparison to the advanced mechanism based material models engineering computational procedures were proven with respect to their applicability and conservatisms. For thermal cyclic loading, test equipment and technique were developed which allow for cyclic thermal loading with temperature ranges between 1 00 C and 300 C and frequencies between 0.1 and 1 Hz. As a result, tests with a temperature range of 150 C and lower showed no crack formation up to 300,000 cycles. For temperature ranges of 200 C and higher multiple crack patterns were observed with the deepest crack of about 1.3 mm after 1,000,000 cycles, whereas the difference in crack depth between 300,000 and 1,000,000 cycles was negligibly small. To model the fatigue lifetime, the D{sub TMF} damage parameter was applied to the low-cycle fatigue and the thermal, high frequent fatigue tests. For thermal fatigue, the analyses predicted in agreement with the tests crack initiation followed by crack propagation, subsequent retardation and arrest. This behaviour can be explained qualitatively and quantitatively using the methods of linear-elastic fracture mechanics, whereas the consideration of the interaction of multiple cracks is essential to describe the experimentally observed crack retardation. The results for thermal fatigue are in the scatterband of the mechanical p and thermo-mechanical fatigue results and the cycles to failure are 10 times higher than those estimated according to the KTA fatigue

High temperature materials and mechanisms

CERN Document Server

2014-01-01

The use of high-temperature materials in current and future applications, including silicone materials for handling hot foods and metal alloys for developing high-speed aircraft and spacecraft systems, has generated a growing interest in high-temperature technologies. High Temperature Materials and Mechanisms explores a broad range of issues related to high-temperature materials and mechanisms that operate in harsh conditions. While some applications involve the use of materials at high temperatures, others require materials processed at high temperatures for use at room temperature. High-temperature materials must also be resistant to related causes of damage, such as oxidation and corrosion, which are accelerated with increased temperatures. This book examines high-temperature materials and mechanisms from many angles. It covers the topics of processes, materials characterization methods, and the nondestructive evaluation and health monitoring of high-temperature materials and structures. It describes the ...

Development of a microindentation technique to determine the fuel mechanical behaviour at high burnup

International Nuclear Information System (INIS)

Baron, D.; Leclercq, S.; Spino, J.; Taheri, S.

1998-01-01

One of the major problems that face the conceptors and users of nuclear power plants is the demonstration of the cladding integrity (the Zircaloy clad that contains the fuel pellets), particularly in class I and II operating conditions. A long term collaboration between EDF and the Applied Mechanics Laboratory (LMA) of Besancon (France) has existed for several years, and a unified modelling of the cladding has been developed in this frame. But a good understanding of the cladding response is not of total use if the mechanical solicitation applied to this clad by the fuel pellet is not completely known. The potential evolution and the non-homogeneity of the fuel stiffness was recently demonstrated by Spino (TUI) on Vickers micro-hardness tests at room temperature. Thus, in order to get furthermore data, TUI and EDF decided to build a specific microindentation device able to perform the tests needed by the modelers. After a brief recall of what the effects of irradiation are on the fuel pellet mechanical behaviour, this paper presents the microindentation device to be built, as well as the principles that underline its use. Finally, the way the experimental results will be used to determine the mechanical behaviour of the fuel pellet under irradiation is pointed out. (author)

Biaxial deformation behaviour of poly-ether-ether-ketone

Science.gov (United States)

Turner, Josh; Menary, Gary; Martin, Peter

2018-05-01

The biaxial tensile properties of thin poly-ether-ether-ketone (PEEK) films are presented. Investigation into the biaxial mechanical behaviour of PEEK films will provide a preliminary insight into the anticipated stress/strain response, and potential suitability, to the possible fabrication of thin walled parts through stretch blow moulding and thermoforming processes - with the multi-axial state of strain imposed onto the heated thermoplastic sheet representative of the expected strain history experienced during these material forming processes. Following identification of the prospective forming temperature window, the biaxial mechanical behaviour of the material is characterized under differing modes of deformation, at a nominal strain rate of 1 s-1. The temperature dependence is outlined within - with an appreciable increase in flow behaviour correlated with specimen temperature exceeding its glass transition temperature (Tg).

Impact of nutrition on canine behaviour: current status and possible mechanisms

OpenAIRE

Bosch, G.; Beerda, B.; Hendriks, W.H.; Poel, van der, A.F.B.; Verstegen, M.W.A.

2007-01-01

Each year, millions of dogs worldwide are abandoned by their owners, relinquished to animal shelters, and euthanised because of behaviour problems. Nutrition is rarely considered as one of the possible contributing factors of problem behaviour. This contribution presents an overview of current knowledge on the influence of nutrition on canine behaviour and explores the underlying mechanisms by which diet may affect behaviour in animals. Behaviour is regulated by neurotransmitters and hormones...

Modelling time-dependent mechanical behaviour of softwood using deformation kinetics

DEFF Research Database (Denmark)

Engelund, Emil Tang; Svensson, Staffan

2010-01-01

The time-dependent mechanical behaviour (TDMB) of softwood is relevant, e.g., when wood is used as building material where the mechanical properties must be predicted for decades ahead. The established mathematical models should be able to predict the time-dependent behaviour. However, these models...... are not always based on the actual physical processes causing time-dependent behaviour and the physical interpretation of their input parameters is difficult. The present study describes the TDMB of a softwood tissue and its individual tracheids. A model is constructed with a local coordinate system that follows...... macroscopic viscoelasticity, i.e., the time-dependent processes are to a significant degree reversible....

Microstructure, consolidation and mechanical behaviour of Mg/n-TiC composite

Directory of Open Access Journals (Sweden)

N. Vijay Ponraj

2016-09-01

Full Text Available In this work, the microstructure, consolidation and mechanical properties of pure magnesium, magnesium based composite containing with different fractions (5, 10, 15 wt% of Titanium carbide nanoparticles (n-TiC were fabricated via powder metallurgy technique. The fabricated composites exhibited homogeneous distribution of TiC with little porosity. Microstructure of the composite and powders was studied using X-ray diffraction, Scanning electron microscope, and Transmission electron microscope. Microstructural characterization of the materials exposed that the accumulation of nanosized titanium carbide reinforcement enhanced the homogenization during mechanical blending. The relative density, compressibility, green compressive strength, sinterability and hardness of the nanocomposites were also examined. The effect of reinforcement on the densification was studied and reported in terms of the relative density and consolidation behaviour of the Magnesium matrix with n-TiC was studied and best compacted fit obtained through the Heckel, Panelli Ambrosio Filho and Ge equations. The compressive strength of the composite significantly increases from 230 MPa to 389 MPa with content of n-TiC and sintering temperature. Experiments have been performed under different conditions of temperature, n-TiC Content, and compacting pressure.

On the hydro-mechanical behaviour of MX80 bentonite-based materials

Directory of Open Access Journals (Sweden)

Yu-Jun Cui

2017-06-01

Full Text Available Bentonite-based materials have been considered in many countries as engineered barrier/backfilling materials in deep geological disposal of high-level radioactive waste. During the long period of waste storage, these materials will play an essential role in ensuring the integrity of the storage system that consists of the waste canisters, the engineered barrier/backfill, the retaining structures as well as the geological barrier. Thus, it is essential to well understand the hydro-mechanical behaviours of these bentonite-based materials. This review paper presents the recent advances of knowledge on MX80 bentonite-based materials, in terms of water retention properties, hydraulic behaviour and mechanical behaviour. Emphasis is put on the effect of technological voids and the role of the dry density of bentonite. The swelling anisotropy is also discussed based on the results from swelling tests with measurements of both axial and radial swelling pressures on a sand-bentonite mixture compacted at different densities. Microstructure observation was used to help the interpretation of macroscopic hydro-mechanical behaviour. Also, the evolution of soil microstructure thus the soil density over time is discussed based on the results from mock-up tests. This evolution is essential for understanding the long-term hydro-mechanical behaviour of the engineered barrier/backfill.

The real gas behaviour of helium as a cooling medium for high-temperature reactors

International Nuclear Information System (INIS)

Hewing, G.

1977-01-01

The article describes the influence of the real gas behaviour on the variables of state for the helium gas and the effects on the design of high-temperature reactor plants. After explaining the basic equations for describing variables and changes of state of the real gas, the real and ideal gas behaviour is analysed. Finally, the influence of the real gas behaviour on the design of high-temperature reactors in one- and two-cycle plants is investigated. (orig.) [de

Solutionizing temperature and abrasive wear behaviour of cast Al-Si-Mg alloys

International Nuclear Information System (INIS)

Sharma, Rajesh; Anesh; Dwivedi, D.K.

2007-01-01

In the present paper, the influence of solutionizing temperature during artificial age hardening treatment (T 6 ) of cast Al-(8, 12, 16%)Si-0.3%Mg on abrasive wear behaviour has been reported. Alloys were prepared by controlled melting and casting. Cast alloys were given artificial age hardening treatment having a sequence of solutionizing, quenching and artificial aging. All the alloys were solutionized at 450 deg. C, 480 deg. C, 510 deg. C, and 550 deg. C for 8 h followed by water quenching (30 deg. C) and aging hardening at 170 deg. C for 12 h. Abrasive wear tests were conducted against 320 grade SiC polishing papers at 5 N and 10 N normal loads. It was observed that the silicon content and solution temperature affected the wear resistance significantly. Increase in solution temperature improved the wear resistance. Hypereutectic alloy showed better wear resistance than the eutectic and hypoeutectic alloys under identical conditions. Optical microstructure study of alloys revealed that the increase in solutionizing temperature improved distribution of silicon grains. Scanning electron microscopy (SEM) of wear surface was carried out to analyze the wear mechanism

Thermo-mechanical behaviour during encapsulation of glass in a steel vessel

International Nuclear Information System (INIS)

Nakhodchi, S.; Smith, D.J.; Thomas, B.G.

2016-01-01

Quantitative numerical simulations and qualitative evaluations are conducted to elucidate thermo-mechanical behaviour during pouring and solidification of molten glass into a stainless-steel cylindrical container. Residual stress and structural integrity in this casting/vitrification process is important because it can be used for long-term storage of high-level nuclear wastes. The predicted temperature and stress distributions in the glass and container agree well with previous measurements of the temperature histories and residual stresses. Three different thermal-stress models are developed using the finite-element method and compared. Two simple slice models were developed based on the generalized plane strain assumption as well as a detailed two-dimensional axi-symmetric model that adds elements according to the stages of pouring glass into the stainless steel container. The results reveal that mechanical interaction between the glass and the wall of the stainless steel container generates residual tensile stresses that approach the yield strength of the steel. Together, these results reveal important insights into the mechanism of stress generation in the process, the structural integrity of the product, and accuracy of the modelling-tool predictions. - Highlights: • Source of residual stresses in glass and stainless steel containers (canisters) is discussed. • Final residual stresses in both glass and container is quantified. • Simple models presented for simulation of complicated casting process. • Comparison between detailed and simple FE modeling.

Temperature behaviour of photoluminescence and electron-beam-induced current recombination behaviour of extended defects in solar grade silicon

CERN Document Server

Arguirov, T; Kittler, M; Reif, J

2002-01-01

The temperature dependence of D-band and band-to-band (BB) luminescence was measured in EFG samples between 80 K and room temperature for defects/dislocations presenting different amounts of contamination. The contamination density was estimated from the temperature behaviour of the electron-beam-induced current contrast, ranging between about 10 sup 4 and 10 sup 6 impurities cm sup - sup 1 dislocation length. The D1 line became already visible at room temperature but its intensity was found to exhibit a maximum at about 150 K. D2, D3 and D4 start to show up at about 250, 190 and 170 K, respectively, and increase their intensities upon lowering temperature. At room temperature the width of the D1 line is broad and becomes narrower upon lowering the temperature. D2 shows the opposite behaviour. The intensities of D1 and D2 were observed to show strong variations across the sample, whereas this was not observed for the pair D4/D3. In particular, the origin of the lines D1 and D2 is still far from being understo...

Micro-Mechanical Temperature Sensors

DEFF Research Database (Denmark)

Larsen, Tom

Temperature is the most frequently measured physical quantity in the world. The field of thermometry is therefore constantly evolving towards better temperature sensors and better temperature measurements. The aim of this Ph.D. project was to improve an existing type of micro-mechanical temperature...... sensor or to develop a new one. Two types of micro-mechanical temperature sensors have been studied: Bilayer cantilevers and string-like beam resonators. Both sensor types utilize thermally generated stress. Bilayer cantilevers are frequently used as temperature sensors at the micro-scale, and the goal....... The reduced sensitivity was due to initial bending of the cantilevers and poor adhesion between the two cantilever materials. No further attempts were made to improve the sensitivity of bilayer cantilevers. The concept of using string-like resonators as temperature sensors has, for the first time, been...

Temperature limits trail following behaviour through pheromone decay in ants

Science.gov (United States)

van Oudenhove, Louise; Billoir, Elise; Boulay, Raphaël; Bernstein, Carlos; Cerdá, Xim

2011-12-01

In Mediterranean habitats, temperature affects both ant foraging behaviour and community structure. Many studies have shown that dominant species often forage at lower temperature than subordinates. Yet, the factors that constrain dominant species foraging activity in hot environments are still elusive. We used the dominant ant Tapinoma nigerrimum as a model species to test the hypothesis that high temperatures hinder trail following behaviour by accelerating pheromone degradation. First, field observations showed that high temperatures (> 30°C) reduce the foraging activity of T. nigerrimum independently of the daily and seasonal rhythms of this species. Second, we isolated the effect of high temperatures on pheromone trail efficacy from its effect on worker physiology. A marked substrate was heated during 10 min (five temperature treatments from 25°C to 60°C), cooled down to 25°C, and offered in a test choice to workers. At hot temperature treatments (>40°C), workers did not discriminate the previously marked substrate. High temperatures appeared therefore to accelerate pheromone degradation. Third, we assessed the pheromone decay dynamics by a mechanistic model fitted with Bayesian inference. The model predicted ant choice through the evolution of pheromone concentration on trails as a function of both temperature and time since pheromone deposition. Overall, our results highlighted that the effect of high temperatures on recruitment intensity was partly due to pheromone evaporation. In the Mediterranean ant communities, this might affect dominant species relying on chemical recruitment, more than subordinate ant species, less dependent on chemical communication and less sensitive to high temperatures.

Dynamic mechanical behaviour of nanoparticle loaded biodegradable PVA films for vaginal drug delivery.

Science.gov (United States)

Traore, Yannick L; Fumakia, Miral; Gu, Jijin; Ho, Emmanuel A

2018-03-01

In this study, we investigated the viscoelastic and mechanical behaviour of polyvinyl alcohol films formulated along with carrageenan, plasticizing agents (polyethylene glycol and glycerol), and when loaded with nanoparticles as a model for potential applications as microbicides. The storage modulus, loss modulus and glass transition temperature were determined using a dynamic mechanical analyzer. Films fabricated from 2% to 5% polyvinyl alcohol containing 3 mg or 5 mg of fluorescently labeled nanoparticles were evaluated. The storage modulus and loss modulus values of blank films were shown to be higher than the nanoparticle-loaded films. Glass transition temperature determined using the storage modulus, and loss modulus was between 40-50℃ and 35-40℃, respectively. The tensile properties evaluated showed that 2% polyvinyl alcohol films were more elastic but less resistant to breaking compared to 5% polyvinyl alcohol films (2% films break around 1 N load and 5% films break around 7 N load). To our knowledge, this is the first study to evaluate the influence of nanoparticle and film composition on the physico-mechanical properties of polymeric films for vaginal drug delivery.

Numerical modelling of the time-dependent mechanical behaviour of softwood

DEFF Research Database (Denmark)

Engelund, Emil Tang

2010-01-01

When using wood as a structural material it is important to consider its time-dependent mechanical behaviour and to predict this behaviour for decades ahead. For this purpose, several rheological mathematical models, spanning from fairly simple to very complex ones, have been developed over...

Microstructural control and high temperature mechanical property of ferritic/martensitic steels for nuclear reactor application

International Nuclear Information System (INIS)

Adetunji, G.J.

1991-04-01

The materials under study are 9-12% Cr ferritic/martensitic steels, alternative candidate materials for application in core components of nuclear power reactors. This work involves (1) Investigation of high temperature fracture mechanism during slow tensile and limited creep testing at 600 o C (2) Extensive study of solute element segregation both theoretically and experimentally (3) Investigation of effects by thermal ageing and irradiation on microstructural developments in relation to high temperature mechanical behaviour. From (1) the results obtained indicate that the important microstructural characteristics controlling the fracture of 9-12% Cr ferritic/martensitic steels at high temperature are (a) solute segregation to inclusion-matrix interfaces (b) hardness of the martensitic matrix and (c) carbide particle size distribution. From (2) the results indicate a strong concentration gradient of silicon and molybdenum near lath packet boundaries for certain quenching rates from the austenitizing temperature. From (3) high temperature tensile data were obtained for irradiated samples with thermally aged ones as control. (author)

Mechanical Behaviour of Glassy Composite Seals for IT-SOFC Application

DEFF Research Database (Denmark)

Nielsen, Karsten Agersted; Solvang, Mette; Nielsen, Sofie Birkedal Lund

2007-01-01

Glass-based sealants have been developed with emphasis on filler material and surface treatment of the sealing components in order to optimise their mechanical and functional behaviour during the initial sealing process as well as during thermal cycling of the SOFC-stack after exposure to operating...... conditions. The bonding strength and microstructure of the interfaces between composite seals and interconnect materials were investigated as a function of surface treatment of the sealing surfaces, glass matrix composition, sealing pressure and temperature. The initial sealing performance and resistance...... to thermal cycling were then investigated on selected combinations of materials after ageing. Strongest bonding between sodium aluminosilicate glass composite and steel surfaces was obtained for sealing at 850°C. For the strongest interface, having shear strength of 2.35 MPa, rupture occurred in the glass...

Effect of water on the mechanical behaviour of shales

International Nuclear Information System (INIS)

Wakim, J.; Hadj-Hassen, F.; Tijani, M.; Noirel, J.F.

2005-01-01

This paper aims to presenting the results of a research conducted in order to study the effect of water on the mechanical behaviour of the Lorraine Basin Colliery shale. The work performed can be divided into four main parts. The first part is dedicated to classical tests and it includes geological and mineralogical analysis as well as mechanical laboratory tests. The second part is devoted to the phenomenon of shale swelling under water effect. New procedures and equipment of testing were set up in order to characterise this swelling behaviour and to determine its model parameters. The tests performed in this second part are allowed to develop a phenomenological model which describes the elasto-visco-plastic behaviour of shales before and after saturation. The last phase of the work is dedicated to implement the new model in the finite element code VIPLEF in order to apply in tunnel excavated in swelling anisotropic rocks. (authors)

Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steel weldments

International Nuclear Information System (INIS)

Gaffard, V.

2004-12-01

Chromium martensitic stainless steels are under development since the 70's with the prospect of using them as structural components in thermal and nuclear power plants. The modified 9Cr1Mo-NbV steel is already used, especially in England and Japan, as a material for structural components in thermal power plants where welding is a commonly used joining technique. New generations of chromium martensitic stainless steels with improved mechanical properties for high pressure and temperature use are currently under development. However, observations of several in-service premature failures of welded components in 9Cr1Mo-NbV steel, outline a strong need for understanding the high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steels and weldments. The present study aimed at experimentally determining and then modelling the high temperature creep flow and damage behaviour of both 9Cr1Mo-NbV steels and weldments (typically in the temperature range from 450 C to 650 C). The base metal was first studied as the reference material. It was especially evidenced that tempered chromium martensitic steels exhibit a change in both creep flow and damage behaviour for long term creep exposure. As a consequence, the classically performed extrapolation of 1,000 hours creep data to 100,000 hours creep lifetime predictions might be very hazardous. Based on experimental observations, a new model, integrating and coupling multiple creep flow and damage mechanisms, was developed in the framework of the mechanics of porous media. It was then successfully used to represent creep flow and damage behaviour of the base metal from high to low stress levels even for complex multiaxial loading conditions. Although the high temperature creep properties of the base metal are quite good, the occurrence of premature failure in weldments in high temperature creep conditions largely focused the attention of the scientific community. The lower creep strength of the weld component was also

Contribution to the explanation of the spalling of small specimen without any mechanical restraint exposed to high temperature

International Nuclear Information System (INIS)

Morais, Marcus V.G. de; Pliya, Prosper; Noumowe, Albert; Beaucour, Anne-Lise; Ortola, Sophie

2010-01-01

The behaviour of concrete subjected to high temperature is studied. The aim of the study is to explain the spalling or bursting phenomenon observed during experimental studies in the laboratory. Mechanical computations are carried out with the finite element code CAST3M developed at the French Atomic Energy Agency (CEA). Heat gradient and water vapour pressure inside the concrete element are determined by using a thermo-hydrous model. Then, the mechanical stresses generated in the studied concrete element are calculated according to two behaviour assumptions: the linear isotropic elastic law and an elastoplastic model. Numerical simulations show that, during the heating cycles, tension stresses are developed in the central part and compression stresses at the surface of the cylindrical concrete element. The highest stresses appear when the surface temperature of the concrete element is about 300 o C. The tension stresses in the specimens then exceed the concrete tensile strength.

Multi-scale modelling of the hydro-mechanical behaviour of argillaceous rocks

International Nuclear Information System (INIS)

Van den Eijnden, Bram

2015-01-01

Feasibility studies for deep geological radioactive waste disposal facilities have led to an increased interest in the geomechanical modelling of its host rock. In France, a potential host rock is the Callovo-Oxfordian clay-stone. The low permeability of this material is of key importance, as the principle of deep geological disposal strongly relies on the sealing capacity of the host formation. The permeability being coupled to the mechanical material state, hydro-mechanical coupled behaviour of the clay-stone becomes important when mechanical alterations are induced by gallery excavation in the so-called excavation damaged zone (EDZ). In materials with microstructure such as the Callovo-Oxfordian clay-stone, the macroscopic behaviour has its origin in the interaction of its micromechanical constituents. In addition to the coupling between hydraulic and mechanical behaviour, a coupling between the micro (material microstructure) and macro scale will be made. By means of the development of a framework of computational homogenization for hydro-mechanical coupling, a double-scale modelling approach is formulated, for which the macro-scale constitutive relations are derived from the microscale by homogenization. An existing model for the modelling of hydro-mechanical coupling based on the distinct definition of grains and intergranular pore space is adopted and modified to enable the application of first order computational homogenization for obtaining macro-scale stress and fluid transport responses. This model is used to constitute a periodic representative elementary volume (REV) that allows the representation of the local macroscopic behaviour of the clay-stone. As a response to deformation loading, the behaviour of the REV represents the numerical equivalent of a constitutive relation at the macro-scale. For the required consistent tangent operators, the framework of computational homogenization by static condensation is extended to hydro-mechanical coupling. The

Activation behaviour of ZrCrNi mechanically milled with nickel

International Nuclear Information System (INIS)

Jung, C. B.; Ho Kim, J.; Sub Lee, K.

1998-01-01

AB 2 type Laves phase alloys have some promising properties as a negative electrode in rechargeable Ni/MH batteries because of high electrochemical capacity and good cyclic life. However, they have the disadvantage of requiring many charge-discharge cycles for activation. In this study, the mechanical milling with nickel has been introduced to modify the electrochemical behaviour of the ZrCrNi alloy. A composite-like structure (ZrCrNi+nickel) and nanocrystalline ZrCrNi were obtained through the mechanical milling and the hydrogenation behaviour of the electrode was greatly improved. (orig.)

High temperature behaviour of self-consolidating concrete

International Nuclear Information System (INIS)

Fares, Hanaa; Remond, Sebastien; Noumowe, Albert; Cousture, Annelise

2010-01-01

This paper presents an experimental study on the properties of self-compacting concrete (SCC) subjected to high temperature. Two SCC mixtures and one vibrated concrete mixture were tested. These concrete mixtures come from the French National Project B-P. The specimens of each concrete mixture were heated at a rate of 1 deg. C/min up to different temperatures (150, 300, 450 and 600 deg. C). In order to ensure a uniform temperature throughout the specimens, the temperature was held constant at the maximum temperature for 1 h before cooling. Mechanical properties at ambient temperature and residual mechanical properties after heating have already been determined. In this paper, the physicochemical properties and the microstuctural characteristics are presented. Thermogravimetric analysis, thermodifferential analysis, X-ray diffraction and SEM observations were used. The aim of these studies was in particular to explain the observed residual compressive strength increase between 150 and 300 deg. C.

Adaptive and freeze-tolerant heteronetwork organohydrogels with enhanced mechanical stability over a wide temperature range

Science.gov (United States)

Gao, Hainan; Zhao, Ziguang; Cai, Yudong; Zhou, Jiajia; Hua, Wenda; Chen, Lie; Wang, Li; Zhang, Jianqi; Han, Dong; Liu, Mingjie; Jiang, Lei

2017-06-01

Many biological organisms with exceptional freezing tolerance can resist the damages to cells from extra-/intracellular ice crystals and thus maintain their mechanical stability at subzero temperatures. Inspired by the freezing tolerance mechanisms found in nature, here we report a strategy of combining hydrophilic/oleophilic heteronetworks to produce self-adaptive, freeze-tolerant and mechanically stable organohydrogels. The organohydrogels can simultaneously use water and oil as a dispersion medium, and quickly switch between hydrogel- and organogel-like behaviours in response to the nature of the surrounding phase. Accordingly, their surfaces display unusual adaptive dual superlyophobic in oil/water system (that is, they are superhydrophobic under oil and superoleophobic under water). Moreover, the organogel component can inhibit the ice crystallization of the hydrogel component, thus enhancing the mechanical stability of organohydrogel over a wide temperature range (-78 to 80 °C). The organohydrogels may have promising applications in complex and harsh environments.

Effect of Temperature on Oscillatory Behaviour of the System Containing Isomers of Hydroxybenzoic Acid in Batch Reactor

Directory of Open Access Journals (Sweden)

Masood A. Nath

2008-01-01

Full Text Available In the present paper a thorough study of temperature dependence on oscillatory behaviour of the Belousov-Zhabotinsky (BZ system containing the isomers of hydroxybenzoic acids + BrO3-+ Mn(II in aqueous acid medium (1.0 M H2SO4 at a fixed concentration of reacting species has been reported. On varying temperature, the oscillatory parameters like induction time, time period and number of oscillations show marked changes. These changes arise due to the position and number of hydroxyl groups in these isomers which affect the oscillations. Experimental observations have satisfactorily been explained by FKN mechanism and kinetic parameters. The oscillatory characteristics depend on the temperature dependence of the rate constant of the reaction controlling the inhibitory reaction steps (negative feedback

Morphology and mechanical behaviour of concretes reinforced by amorphous cast fibres

International Nuclear Information System (INIS)

Redon, Carl

1997-01-01

This research thesis addresses the characterization of the morphology and mechanical behaviour of concretes reinforced by amorphous cast fibres. It first gathers some general characteristics and observations related to the amorphous cast fibre: roughness, failure mode, amorphous structure, X-ray analysis, fire resistance. Experimental methods and techniques developed for morphological analysis and mechanical tests are presented (sample preparation, tensile test, and compression sample) and the use of image automatic analysis techniques is then addressed (void morphology and granulometry analysis, inter-void distance measurement, fibre spatial distribution). The next part reports the study of the mechanical behaviour under axial compression [fr

Combined Effect of Pressure and Temperature on the Viscous Behaviour of All-Oil Drilling Fluids

Directory of Open Access Journals (Sweden)

Hermoso J.

2014-12-01

Full Text Available The overall objective of this research was to study the combined influence of pressure and temperature on the complex viscous behaviour of two oil-based drilling fluids. The oil-based fluids were formulated by dispersing selected organobentonites in mineral oil, using a high-shear mixer, at room temperature. Drilling fluid viscous flow characterization was performed with a controlled-stress rheometer, using both conventional coaxial cylinder and non-conventional geometries for High Pressure/High Temperature (HPHT measurements. The rheological data obtained confirm that a helical ribbon geometry is a very useful tool to characterise the complex viscous flow behaviour of these fluids under extreme conditions. The different viscous flow behaviours encountered for both all-oil drilling fluids, as a function of temperature, are related to changes in polymer-oil pair solvency and oil viscosity. Hence, the resulting structures have been principally attributed to changes in the effective volume fraction of disperse phase due to thermally induced processes. Bingham’s and Herschel-Bulkley’s models describe the rheological properties of these drilling fluids, at different pressures and temperatures, fairly well. It was found that Herschel-Bulkley’s model fits much better B34-based oil drilling fluid viscous flow behaviour under HPHT conditions. Yield stress values increase linearly with pressure in the range of temperature studied. The pressure influence on yielding behaviour has been associated with the compression effect of different resulting organoclay microstructures. A factorial WLF-Barus model fitted the combined effect of temperature and pressure on the plastic viscosity of both drilling fluids fairly well, being this effect mainly influenced by the piezo-viscous properties of the continuous phase.

Mechanical behaviour׳s evolution of a PLA-b-PEG-b-PLA triblock copolymer during hydrolytic degradation.

Science.gov (United States)

Breche, Q; Chagnon, G; Machado, G; Girard, E; Nottelet, B; Garric, X; Favier, D

2016-07-01

PLA-b-PEG-b-PLA is a biodegradable triblock copolymer that presents both the mechanical properties of PLA and the hydrophilicity of PEG. In this paper, physical and mechanical properties of PLA-b-PEG-b-PLA are studied during in vitro degradation. The degradation process leads to a mass loss, a decrease of number average molecular weight and an increase of dispersity index. Mechanical experiments are made in a specific experimental set-up designed to create an environment close to in vivo conditions. The viscoelastic behaviour of the material is studied during the degradation. Finally, the mechanical behaviour is modelled with a linear viscoelastic model. A degradation variable is defined and included in the model to describe the hydrolytic degradation. This variable is linked to physical parameters of the macromolecular polymer network. The model allows us to describe weak deformations but become less accurate for larger deformations. The abilities and limits of the model are discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Experimental study on the thermo-mechanical behaviour of stiff clay under non-isotropic stress state

International Nuclear Information System (INIS)

Tang, Anh Minh; Cui, Yu-Jun; Li, Xiang-Ling

2012-01-01

Document available in extended abstract form only. Stiff clay is usually considered as possible host-rock for geological radioactive waste disposal due to its low permeability and its self-sealing capacity. Boom Clay, for instance, is one of the clays currently considered by the Belgian radioactive waste management agency Ondraf/Niras as a potential host for a geological repository. In order to analyse the performance of this material, it is important to understand its behaviour under the coupled thermo-hydro-mechanical solicitations. In laboratory, several studies have been performed to study the volume change of clay under coupled thermomechanical loading. The results show that heating under drained conditions can induce thermal dilation at low confining stress and thermal contraction at high confining stress. On the other hand, compression tests performed at constant temperature show that the compressibility parameters of soil can be modified by temperature change. These features are now well considered in constitutive laws based on the framework of elasto-plasticity. Under undrained conditions, heating can increase pore-water pressure and this behaviour can be simulated using the theoretical thermo-poro-elastic framework. The temperature effect on the soil behaviour under triaxial compression is also often considered. It is commonly accepted that heating decreases the shear strength of clay but this softening can be hidden by the thermal contraction that occurs during heating which can induce at the same time soil hardening. In spite of these existing works, laboratory tests considering the thermo-mechanical loading path that the soil can be subjected to are still rare. Actually, in the case of geological radioactive waste disposal, after the installation of waste canisters, the soil is expected to be heated under non-isotropic stress state. Most of the existing laboratory works show heating tests in odometer cell or triaxial cell under isotropic stress

Mechanical Behaviour of Inconel 718 Thin-Walled Laser Welded Components for Aircraft Engines

Directory of Open Access Journals (Sweden)

Enrico Lertora

2014-01-01

Full Text Available Nickel alloys are very important in many aerospace applications, especially to manufacture gas turbines and aero engine components, where high strength and temperature resistance are necessary. These kinds of alloys have to be welded with high energy density processes, in order to preserve their high mechanical properties. In this work, CO2 laser overlap joints between Inconel 718 sheets of limited thickness in the absence of postweld heat treatment were made. The main application of this kind of joint is the manufacturing of a helicopter engine component. In particular the aim was to obtain a specific cross section geometry, necessary to overcome the mechanical stresses found in these working conditions without failure. Static and dynamic tests were performed to assess the welds and the parent material fatigue life behaviour. Furthermore, the life trend was identified. This research pointed out that a full joint shape control is possible by choosing proper welding parameters and that the laser beam process allows the maintenance of high tensile strength and ductility of Inconel 718 but caused many liquation microcracks in the heat affected zone (HAZ. In spite of these microcracks, the fatigue behaviour of the overlap welds complies with the technical specifications required by the application.

Factors influencing the mechanical behaviour of healthy human descending thoracic aorta

International Nuclear Information System (INIS)

Guinea, Gustavo V; Atienza, José M; Rojo, Francisco J; Yiqun, Li; Claes, Els; Elices, Manuel; García-Herrera, Claudio M; Goicolea, José M; García-Montero, Carlos; Burgos, Raúl L; Goicolea, Francisco J

2010-01-01

In recent times, significant effort has been made to understand the mechanical behaviour of the arterial wall and how it is affected by the different vascular pathologies. However, to be able to interpret the results correctly, it is essential that the influence of other factors, such as aging or anisotropy, be understood. Knowledge of mechanical behaviour of the aorta has been customarily constrained by lack of data on fresh aortic tissue, especially from healthy young individuals. In addition, information regarding the point of rupture is also very limited. In this study, the mechanical behaviour of the descending thoracic aorta of 28 organ donors with no apparent disease, whose ages vary from 17 to 60 years, is evaluated. Tensile tests up to rupture are carried out to evaluate the influence of age and wall anisotropy. Results reveal that the tensile strength and stretch at failure of healthy descending aortas show a significant reduction with age, falling abruptly beyond the age of 30. This fact places age as a key factor when mechanical properties of descending aorta are considered

Contribution to the explanation of the spalling of small specimen without any mechanical restraint exposed to high temperature

Energy Technology Data Exchange (ETDEWEB)

Morais, Marcus V.G. de, E-mail: mvmorais@unb.b [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Pliya, Prosper [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Noumowe, Albert, E-mail: Albert.Noumowe@u-cergy.f [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France); Beaucour, Anne-Lise; Ortola, Sophie [Cergy-Pontoise University - L2MGC, 5 mail Gay-Lussac Neuville sur Oise, 95031 Cergy-Pontoise Cedex (France)

2010-10-15

The behaviour of concrete subjected to high temperature is studied. The aim of the study is to explain the spalling or bursting phenomenon observed during experimental studies in the laboratory. Mechanical computations are carried out with the finite element code CAST3M developed at the French Atomic Energy Agency (CEA). Heat gradient and water vapour pressure inside the concrete element are determined by using a thermo-hydrous model. Then, the mechanical stresses generated in the studied concrete element are calculated according to two behaviour assumptions: the linear isotropic elastic law and an elastoplastic model. Numerical simulations show that, during the heating cycles, tension stresses are developed in the central part and compression stresses at the surface of the cylindrical concrete element. The highest stresses appear when the surface temperature of the concrete element is about 300 {sup o}C. The tension stresses in the specimens then exceed the concrete tensile strength.

Behaviour of Mechanically Laminated CLT Members

Science.gov (United States)

Kuklík, P.; Velebil, L.

2015-11-01

Cross laminated timber (CLT) is one of the structural building systems based on the lamination of multiple layers, where each layer is oriented perpendicularly to each other. Recent requirements are placed to develop an alternative process based on the mechanical lamination of the layers, which is of particular interest to our research group at the University Centre for Energy Efficient Buildings. The goal is to develop and verify the behaviour of mechanically laminated CLT wall panels exposed to shear stresses in the plane. The shear resistance of mechanically jointed CLT is ensured by connecting the layers by screws. The paper deals with the experimental analysis focused on the determination of the torsional stiffness and the slip modulus of crossing areas for different numbers of orthogonally connected layers. The results of the experiments were compared with the current analytical model.

Non-linear behaviour of multi-phase MOX fuels: a micro-mechanical approach

International Nuclear Information System (INIS)

Rousette, S.; Gatt, J.M.; Michel, J.C.

2005-01-01

The modelling of mechanical pellet-clad interaction requires knowledge of the thermo-mechanical behaviour of nuclear fuels. Some nuclear fuels such as MOX are composed of several phases. The mechanical properties of these phases, which are elasto-visco-plastic in-pile, are changing in-pile. The objective is to formulate a mechanical behaviour law taking all the physical phenomena into account in the different phases, which can easily be introduced into a fuel rod modelling code. Consequently, Non-uniform Transformation Field Analysis (NTFA) is used on the one hand, to correctly capture the heterogeneity of the anelastic strain in the different phases and, on the other hand, to provide a simple overall constitutive law for computational codes. This method is a good way to describe the behaviour of MOX fuel. Transformation Field Analysis (TFA), which corresponds to piecewise uniform transformation fields, is used to perform a sensitivity study. (authors)

Tribological behaviour at high temperature of hard CrAlN coatings doped with Y or Zr

International Nuclear Information System (INIS)

Sánchez-López, J.C.; Contreras, A.; Domínguez-Meister, S.; García-Luis, A.; Brizuela, M.

2014-01-01

The tribological properties of CrAlN, CrAlYN and CrAlZrN coatings deposited by direct current reactive magnetron sputtering are studied by means of pin-on-disc experiments at room temperature, 300, 500 and 650 °C using alumina balls as counterparts. The influence of the metallic composition (Al, Y and Zr) on the friction, wear properties and oxidation resistance is studied by means of scanning electron microscopy, energy dispersive X-ray analysis and Raman analysis of the contact region after the friction tests. The results obtained allow us to classify the tribological behaviour of the CrAl(Y,Zr)N coatings into three groups according to the nature of the dopant and aluminium content. The sliding wear mechanism is characterized by the formation of an overcoat rich in chromium and aluminium oxides whose particular composition is determined by the initial chemical characteristics of the coating and the testing temperature. The fraction of Cr 2 O 3 becomes more significant as the Al content decreases and the temperature increases. The addition of Y, and particularly Zr, favours the preferential formation of Cr 2 O 3 versus CrO 2 leading to a reduction of friction and wear of the counterpart. Conversely, the tribological behaviour of pure CrAlN coatings is characterized by higher friction but lower film wear rates as a result of higher hardness and major presence of aluminium oxides on the coating surface. - Highlights: • Comparative tribological study at high temperature of CrAlN, CrAlYN and CrAlZrN films • Fraction of Cr 2 O 3 raises as the Al content decreases and the temperature increases. • Zr doping favours lower and steady friction coefficient due to higher Cr 2 O 3 formation. • Sliding wear mechanism becomes predominantly abrasive as the Al content increases. • Excellent tribological performance of CrAlN doped with low Y contents (≈ 2 at.%)

Thermomechanical analysis of Natural Rubber behaviour stressed at room temperature.

Directory of Open Access Journals (Sweden)

Chrysochoos A.

2010-06-01

Full Text Available Owing to their high molecular mobility, stressed rubber chains can easily change their conformations and get orientated. This phenomena leads to so high reversible draw ratio that this behaviour is called rubber elasticity [1-3]. The analogy with ideal gases leads to an internal energy independent of elongation, the stress being attributed to a so-called configuration entropy. However, this analysis cannot take thermal expansion into account and moreover prohibits predicting standard thermo-elastic effect noticed at small elongations and the thermoelastic inversion effects [4]. This paper aims at : observing and quantifying dissipative and coupling effects associated with deformation energy, generated when Natural Rubber is stretched. re-examine the thermomechanical behaviour model of rubberlike materials, under the generalised standard material concept. From an experimental viewpoint, energy balance is created using infrared and quantitative imaging techniques. Digital Image Correlation (DIC provides in-the-plane displacement fields and, after derivation, strain and strain-rate fields. We have used those techniques to evidence the thermoelastic inversion effect as shown on Figure 1 where different weights have been fixed to warmed specimen and we monitored the sample deformation while it recovers room temperature. But we have also used those techniques to perform energy balance : analysis of the mechanical equilibrium allows estimates of the stress pattern and computation of deformation energy rates under a plane stress hypothesis [5]. Infrared Thermography (IRT gives the surface temperature of the sample. To estimate the distribution of heat sources, image processing with a local heat equation and a minimal set of approximation functions (image filtering was used. The time courses of deformation energy and heat associated with cyclic process are plotted in Figure 2. The time derivatives of both forms of energy are approximately similar. This

Thermal and mechanical behaviour of the reduced-activation-ferritic-martensitic steel EUROFER

International Nuclear Information System (INIS)

Lindau, R.; Moeslang, A.; Schirra, M.

2002-01-01

Reduced activation ferritic/martensitic (RAFM) steels are being considered for structural application in potential fusion energy systems. Based on the substantial experience with RAFM developmental steels of OPTIFER type, an industrial 3.5 tons batch of a 9CrWVTa-RAFM steel, called EUROFER 97 had been specified and ordered. A characterisation programme has been launched to determine the relevant mechanical and physical-metallurgical properties in order to qualify the steel for fusion application. The hardening, tempering and transformation behaviour of EUROFER is in good agreement with that of other RAFM-steels like OPTIFER and the Japanese industrial scale heat F82H mod. Tensile tests, performed between RT and 750 deg. C, show comparable strength and ductility values that are not strongly affected by different heat treatments and ageing at 580 and 600 deg. C up to 3300 h. Impact bending tests indicate a superior ductile to brittle transition temperature (DBTT) of EUROFER in the as-received condition compared with that of F82H mod. Creep tests between 450 and 650 deg. C up to test times of 15000 h reveal a creep strength similar to other RAFM steels like OPTIFER and F82H mod. EUROFER shows a good low-cycle fatigue behaviour with longer lifetimes than F82H mod. The deformation and softening behaviour is similar

Effect of strain rate and temperature on mechanical properties of selected building Polish steels

Directory of Open Access Journals (Sweden)

Moćko Wojciech

2015-01-01

Full Text Available Currently, the computer programs of CAD type are basic tool for designing of various structures under impact loading. Application of the numerical calculations allows to substantially reduce amount of time required for the design stage of such projects. However, the proper use of computer aided designing technique requires input data for numerical software including elastic-plastic models of structural materials. This work deals with the constitutive model developed by Rusinek and Klepaczko (RK applied for the modelling of mechanical behaviour of selected grades structural St0S, St3SX, 18GS and 34GS steels and presents here results of experimental and empirical analyses to describe dynamic elastic-plastic behaviours of tested materials at wide range of temperature. In order to calibrate the RK constitutive model, series of compression tests at wide range of strain rates, including static, quasi-static and dynamic investigations at lowered, room and elevated temperatures, were carried out using two testing stands: servo-hydraulic machine and split Hopkinson bar. The results were analysed to determine influence of temperature and strain rate on visco-plastic response of tested steels, and show good correlation with experimental data.

Fracture mechanics behaviour of neutron irradiated Alloy A-286

International Nuclear Information System (INIS)

Mills, W.J.; James, L.A.

The effect of fast-neutron irradiation on the fatigue-crack propagation and fracture toughness behaviour of Alloy A-286 was characterized using fracture mechanics techniques. The fracture toughness was found to decrease continuously with increasing irradiation damage at both 24 deg. C and 427 deg. C. In the unirradiated and low fluence conditions, specimens displayed appreciable plasticity prior to fracture, and equivalent Ksub(Ic) values were determined from Jsub(Ic) fracture toughness results. At high irradiation exposure levels, specimens exhibited a brittle Ksub(Ic) fracture mode. The 427 deg. C fracture toughness fell from 129 MPa√m in the unirradiated condition to 35 MPa√m at an exposure of 16.2 dpa (total fluence of 5.2x10 22 n/cm 2 ). Room temperature fracture toughness values were consistently 40 to 60 percent higher than the 427 deg. C values. Electron fractography revealed that the reduction in fracture resistance was attributed to a fracture mechanism transition from ductile microvoid coalescence to channel fracture. Fatigue-crack propagation tests were conducted at 427 deg. C on specimens irradiated at 2.4 dpa and 16.2 dpa. Crack growth rates at the lower exposure level were comparable to those in unirradiated material, while those at the higher exposure were slightly higher than in unirradiated material. (author)

Evolutionarily conserved mechanisms for the selection and maintenance of behavioural activity.

Science.gov (United States)

Fiore, Vincenzo G; Dolan, Raymond J; Strausfeld, Nicholas J; Hirth, Frank

2015-12-19

Survival and reproduction entail the selection of adaptive behavioural repertoires. This selection manifests as phylogenetically acquired activities that depend on evolved nervous system circuitries. Lorenz and Tinbergen already postulated that heritable behaviours and their reliable performance are specified by genetically determined programs. Here we compare the functional anatomy of the insect central complex and vertebrate basal ganglia to illustrate their role in mediating selection and maintenance of adaptive behaviours. Comparative analyses reveal that central complex and basal ganglia circuitries share comparable lineage relationships within clusters of functionally integrated neurons. These clusters are specified by genetic mechanisms that link birth time and order to their neuronal identities and functions. Their subsequent connections and associated functions are characterized by similar mechanisms that implement dimensionality reduction and transition through attractor states, whereby spatially organized parallel-projecting loops integrate and convey sensorimotor representations that select and maintain behavioural activity. In both taxa, these neural systems are modulated by dopamine signalling that also mediates memory-like processes. The multiplicity of similarities between central complex and basal ganglia suggests evolutionarily conserved computational mechanisms for action selection. We speculate that these may have originated from ancestral ground pattern circuitries present in the brain of the last common ancestor of insects and vertebrates. © 2015 The Authors.

Mechanical properties of rock at high temperatures

International Nuclear Information System (INIS)

Kinoshita, Naoto; Abe, Tohru; Wakabayashi, Naruki; Ishida, Tsuyoshi.

1997-01-01

The laboratory tests have been performed in order to investigate the effects of temperature up to 300degC and pressure up to 30 MPa on the mechanical properties of three types of rocks, Inada granite, Sanjoume andesite and Oya tuff. The experimental results indicated that the significant differences in temperature dependence of mechanical properties exist between the three rocks, because of the difference of the factors which determine the mechanical properties of the rocks. The effect of temperature on the mechanical properties for the rocks is lower than that of pressure and water content. Temperature dependence of the mechanical properties is reduced by increase in pressure in the range of pressure and temperature investigated in this paper. (author)

Corrosion behaviour of high temperature alloys in impure helium environments

International Nuclear Information System (INIS)

Shindo, Masami; Quadakkers, W.J.; Schuster, H.

1986-01-01

Corrosion tests with Ni-base high temperature alloys were carried out at 900 and 950 0 C in simulated high temperature reactor helium environments. It is shown that the carburization and decarburization behaviour is strongly affected by the Cr and Ti(Al) contents of the alloys. In carburizing environments, additions of Ti, alone or in combination with Al, significantly improve the carburization resistance. In oxidizing environment, the alloys with high Cr and Al(Ti) contents are the most resistant against decarburization. In this environment alloys with additions of Ti and Al show poor oxidation resistance. The experimental results obtained are compared with a recently developed theory describing corrosion of high temperature alloys in high temperature reactor helium environments. (orig.)

The anisotropic mechanical behaviour of zircaloy-2

International Nuclear Information System (INIS)

Ballinger, R.; Pelloux, R.M.

1980-01-01

Zirconium alloys used in the LWR industry crystallize in the hexagonal crystal structure below approximately 1136 K and many of the fabrication steps are performed below this temperature. The hexagonal structure possesses a limited number of slip systems and normal deformation processes result in extensive twinning. The twinning process results in the development of a fabrication texture, the type and extent of which is a function of the strain path used in the fabrication process. The texture which develops is important for two reasons. First, the texture at a given point in the fabrication process will determine the ease with which the next strain increment may be taken. Second, the texture of the completed part will have a significant effect on its in service performance because properties such as yield strength, creep strength, and fatigue and stress corrosion cracking resistance are a strong function of texture. Currently there is little data available concerning the evolution of textures as a function of strain path during the fabrication process of Zircaloy. Consequently this experimental investigation was conducted to determine the effect of textures on the mechanical behaviour of Zircaloy-2 with a primary emphasis on the evolution of texture during plastic deformation. (author)

Mechanical and microstructural behaviour of alumina-zirconia ceramic filaments for high temperature applications; Comportement mecanique et microstructure de filaments ceramiques alumine-zircone pour applications a haute temperature

Energy Technology Data Exchange (ETDEWEB)

Poulon-Quintin, A

2002-04-01

This thesis is a contribution to the development and to the study of two-phase alumina-zirconia ceramic filaments resistant to creep and chemical and microstructural degradation. The materials studied are experimental two-phase filaments (diameter of few millimeters) with a fibrillary structure obtained by coextrusion of sol-gels or of powder pastes and a nanocrystalline fiber of thin diameter (11{mu}m) with a homogeneous structure. They have been respectively perfected and chosen for their very promising microstructures and compositions concerning the creep resistance. This study is concentrated on the mechanical characterization at high temperature of these materials and especially on the understanding of the deformation and rupture mechanisms in relation with the microstructural evolution. The commercial fiber (Nextel 650) is a {alpha} alumina (grain size {>=}0.1{mu}m) in which the grains of the second phase zirconia are dispersed in a homogeneous way in intra (5-10 nm) as in inter-granular (20-30 nm). After a heat treatment at temperatures superior to 1200 C, it can be noted a strong grains growth preferentially to the axis of the fiber. The tensile properties decrease to a considerable extent with high temperatures ({>=}1000 C). The creep behaviour has been determined between 1000 and 1300 C (value of 2.5 for the stress exponent and of 850 kJ/mol for the activation energy). The evolution of the microstructure to a long grains microstructure is favourable for the creep resistance. A comparison with other fibers of compositions near the Nextel 650 fiber show that the Nextel 650 fiber has interesting properties for being used at high temperatures (until 1200 C). The study of co-extruded alumina-zirconia filaments with a fibrillary structure has at first required those of filaments which composition are each of the phases obtained from pastes (powder-thermoplastics or sol-gels). The composition of each of the phases has been optimized in order to adapt the

Genetic variablilities of body temperature and resting behaviour in ...

African Journals Online (AJOL)

This implies that neither progeny nor generation had effect on body temperature. The Alpha strain exhibited more resting behaviour than did the exotic and the pure native types. Majority of the birds rested in the afternoon at 2.00 pm. This could be attributed to the fact that at 2.00 pm the weather is hot and birds search for a ...

Long term leaching of silicate systems: testing procedure, actinides behaviour and mechanism

International Nuclear Information System (INIS)

Louwrier, K.; Matzke, H.; Ray, I.; Thiele, H.; Scheffler, K.; Riege, U.

1977-06-01

High-level waste borosilicate glasses and medium-level waste cement products have been leached with various aqueous solutions at ambient temperature. The leach rates of americium and plutonium are determined as well as the behaviour of the actinides in the boundary surface glass/leachant and in the leachant itself. Methods like light-scattering photometry and differential refractometry, molecular filtration, scanning electron microscopy and α-spectrometry of the energy-loss of α-particles in thin layers have been applied. From the experimental results a general model for the leaching mechanism has been established. A critical review of leach test procedures is accomplished aiming at the improvement of common tests with respect to the extrapolation of the obtained leach test data to final disposal safety considerations. (orig.) [de

Mechanical behaviour of synthetic surgical meshes: finite element simulation of the herniated abdominal wall.

Science.gov (United States)

Hernández-Gascón, B; Peña, E; Melero, H; Pascual, G; Doblaré, M; Ginebra, M P; Bellón, J M; Calvo, B

2011-11-01

The material properties of meshes used in hernia surgery contribute to the overall mechanical behaviour of the repaired abdominal wall. The mechanical response of a surgical mesh has to be defined since the haphazard orientation of an anisotropic mesh can lead to inconsistent surgical outcomes. This study was designed to characterize the mechanical behaviour of three surgical meshes (Surgipro®, Optilene® and Infinit®) and to describe a mechanical constitutive law that accurately reproduces the experimental results. Finally, through finite element simulation, the behaviour of the abdominal wall was modelled before and after surgical mesh implant. Uniaxial loading of mesh samples in two perpendicular directions revealed the isotropic response of Surgipro® and the anisotropic behaviour of Optilene® and Infinit®. A phenomenological constitutive law was used to reproduce the measured experimental curves. To analyze the mechanical effect of the meshes once implanted in the abdomen, finite element simulation of the healthy and partially herniated repaired rabbit abdominal wall served to reproduce wall behaviour before and after mesh implant. In all cases, maximal displacements were lower and maximal principal stresses higher in the implanted abdomen than the intact wall model. Despite the fact that no mesh showed a behaviour that perfectly matched that of abdominal muscle, the Infinit® mesh was able to best comply with the biomechanics of the abdominal wall. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Modelling the mechanical behaviour of heterogeneous Ta/TA6V welded joints: behaviour and failure criteria

International Nuclear Information System (INIS)

Paris, Th.

2008-12-01

As laser welding of two different materials (heterogeneous welding) leads to a joint having a characteristic size close to the millimetre, i.e. much smaller than that of a structure, and as such a junction displays completely different mechanical properties because of the metallurgical transformations induced by intense thermal loading, the aim of this research thesis is to develop a behaviour model, flexible and robust enough, to represent all together the mechanical behaviours of the Ta, the TA6V and the melted zone. This model must be able to take plasticity and visco-plasticity into account, and also to provide a failure criterion through damage mechanics and its coupling with the behaviour. The author first reports the experimental characterization of the base materials (Ta and TA6V) by using tensile tests under different strain rates and different directions, relaxation tests and fatigue shear tests. He also characterizes the melted zone by describing the influence of a thermal treatment (induced by welding) on the formation of the melted zone, and by using different tests: four point bending on notched specimens, nano-indentation test, and longitudinal tensile test. In a second part, the author develops the model within the framework of continuum thermodynamics, and explores the numerical issues. The last part deals with the validation of the model for the concerned materials (Ta and TA6V) and melted zone

Time-dependent Fracture Behaviour of Polyampholyte Hydrogels

Science.gov (United States)

Sun, Tao Lin; Luo, Feng; Nakajima, Tasuku; Kurokawa, Takayuki; Gong, Jian Ping

Recently, we report that polyampholytes, polymers bearing randomly dispersed cationic and anionic repeat groups, form tough and self-healing hydrogels with excellent multiple mechanical functions. The randomness makes ionic bonds with a wide distribution of strength, via inter and intra chain complexation. As the breaking and reforming of ionic bonds are time dependent, the hydrogels exhibit rate dependent mechanical behaviour. We systematically studied the tearing energy by tearing test with various tearing velocity under different temperature, and the linear viscoelastic behaviour over a wide range of frequency and temperature. Results have shown that the tearing energy markedly increase with the crack velocity and decrease with the measured temperature. In accordance with the prediction of Williams, Landel, and Ferry (WLF) rate-temperature equivalence, a master curve of tearing energy dependence of crack velocity can be well constructed using the same shift factor from the linear viscoelastic data. The scaling relation of tearing energy as a function of crack velocity can be predicted well by the rheological data according to the developed linear fracture mechanics.

Identification of the mechanical behaviour of biopolymer composites using multistart optimisation technique

KAUST Repository

Brahim, Elhacen

2013-10-01

This paper aims at identifying the mechanical behaviour of starch-zein composites as a function of zein content using a novel optimisation technique. Starting from bending experiments, force-deflection response is used to derive adequate mechanical parameters representing the elastic-plastic behaviour of the studied material. For such a purpose, a finite element model is developed accounting for a simple hardening rule, namely isotropic hardening model. A deterministic optimisation strategy is implemented to provide rapid matching between parameters of the constitutive law and the observed behaviour. Results are discussed based on the robustness of the numerical approach and predicted tendencies with regards to the role of zein content. © 2013 Elsevier Ltd.

A novel laparoscopic grasper with two parallel jaws capable of extracting the mechanical behaviour of soft tissues.

Science.gov (United States)

Nazarynasab, Dariush; Farahmand, Farzam; Mirbagheri, Alireza; Afshari, Elnaz

2017-07-01

Data related to force-deformation behaviour of soft tissue plays an important role in medical/surgical applications such as realistically modelling mechanical behaviour of soft tissue as well as minimally invasive surgery (MIS) and medical diagnosis. While the mechanical behaviour of soft tissue is very complex due to its different constitutive components, some issues increase its complexity like behavioural changes between the live and dead tissues. Indeed, an adequate quantitative description of mechanical behaviour of soft tissues requires high quality in vivo experimental data to be obtained and analysed. This paper describes a novel laparoscopic grasper with two parallel jaws capable of obtaining compressive force-deformation data related to mechanical behaviour of soft tissues. This new laparoscopic grasper includes four sections as mechanical hardware, sensory part, electrical/electronical part and data storage part. By considering a unique design for mechanical hardware, data recording conditions will be close to unconfined-compression-test conditions; so obtained data can be properly used in extracting the mechanical behaviour of soft tissues. Also, the other distinguishing feature of this new system is its applicability during different laparoscopic surgeries and subsequently obtaining in vivo data. However, more preclinical examinations are needed to evaluate the practicality of the novel laparoscopic grasper with two parallel jaws.

Mechanical behaviour of Arabica coffee (Coffea arabica) beans under loading compression

Science.gov (United States)

Sigalingging, R.; Herak, D.; Kabutey, A.; Sigalingging, C.

2018-02-01

The uniformity of the product of the grinding process depends on various factors including the brittleness of the roasted coffee bean and it affects the extraction of soluble solids to obtain the coffee brew. Therefore, the reaching of a certain degree of brittleness is very important for the grinding to which coffee beans have to be subjected to before brewing. The aims of this study to show the mechanical behaviour of Arabica coffee beans from Tobasa (Indonesia) with roasted using different roasting time (40, 60 and 80 minutes at temperature 174 °C) under loading compression 225 kN. Universal compression testing machine was used with pressing vessel diameter 60 mm and compression speed 10 mm min-1 with different initial pressing height ranging from 20 to 60 mm. The results showed that significant correlation between roasting time and the brittleness.

Shell colour, temperature, (micro)habitat structure and predator pressure affect the behaviour of Cepaea nemoralis

Science.gov (United States)

Rosin, Zuzanna M.; Kwieciński, Zbigniew; Lesicki, Andrzej; Skórka, Piotr; Kobak, Jarosław; Szymańska, Anna; Osiejuk, Tomasz S.; Kałuski, Tomasz; Jaskulska, Monika; Tryjanowski, Piotr

2018-06-01

Although shell colour polymorphism of the land snail Cepaea nemoralis is a well-known phenomenon, proximate and ultimate factors driving its evolution remain uncertain. Polymorphic species show variation in behavioural responses to selective forces. Therefore, we estimated effects of various environmental factors (temperature, humidity, food availability, (micro)habitat structure and predatory pressure) on behavioural response (frequency of locomotion, climbing and hiding) of C. nemoralis morphs, in experimental and natural conditions. In the experimental part of study, the frequency of locomotion was negatively affected by temperature and the presence of food and positively influenced by the presence of light. Morphs significantly differed in behavioural responses to environmental variability. Pink mid-banded and yellow five-banded morphs climbed less often and hide in shelter more often than yellow and pink unbanded individuals when temperature was low and food was absent. Snails fed most often at moderate temperature compared to low and high temperatures. Field investigations partially confirmed differences among morphs in frequency of climbing, but not in terms of probability of hiding in sheltered sites. In natural colonies, temperature and (micro)habitat structure significantly affected frequency of climbing as well as hiding in shelter. Snails more often hid in sheltered sites where thrushes preyed on Cepaea. Tendency of unbanded morphs to climb trees may have evolved under avian predatory pressure as thrushes forage on a ground. Tendency of banded morphs to hide in sheltered sites may reflect prey preferences for cryptic background. The results implicate that differential behaviour of C. nemoralis morphs compensate for their morphological and physiological limitations of adaptation to habitat.

Mechanical characterization of alloys in extreme conditions of high strain rates and high temperature

Science.gov (United States)

Cadoni, Ezio

2018-03-01

The aim of this paper is the description of the mechanical characterization of alloys under extreme conditions of temperature and loading. In fact, in the frame of the Cost Action CA15102 “Solutions for Critical Raw Materials Under Extreme Conditions (CRM-EXTREME)” this aspect is crucial and many industrial applications have to consider the dynamic response of materials. Indeed, for a reduction and substitution of CRMs in alloys is necessary to design the materials and understand if the new materials behave better or if the substitution or reduction badly affect their performance. For this reason, a deep knowledge of the mechanical behaviour at high strain-rates of considered materials is required. In general, machinery manufacturing industry or transport industry as well as energy industry have important dynamic phenomena that are simultaneously affected by extended strain, high strain-rate, damage and pressure, as well as conspicuous temperature gradients. The experimental results in extreme conditions of high strain rate and high temperature of an austenitic stainless steel as well as a high-chromium tempered martensitic reduced activation steel Eurofer97 are presented.

Plasticity in behavioural responses and resistance to temperature stress in Musca domestica

DEFF Research Database (Denmark)

Kjaersgaard, Anders; Blackenhorn, Wolf U.; Pertoldi, Cino

2015-01-01

, at the stressful high temperature Spanish flies flew the furthest and Danish flies the shortest distance. Neither body size nor wing loading affected flight performance, although flies with narrower wings tended to fly further (wing shape effect). Swiss flies were most active in terms of locomotor activity......Organisms can respond to and cope with stressful environments in a number of ways including behavioural, morphological and physiological adjustments. To understand the role of behavioural traits in thermal adaptations we compared heat resistance, locomotor (walking and flying) activity, flight...... performance and morphology of three European populations of Musca domestica (Diptera: Muscidae) originating from different thermal conditions (Spain, Switzerland and Denmark) at benign and stressful high temperatures. Spanish flies showed greater heat resistance than Swiss and Danish flies. Similarly...

A Fine Grain, High Mn Steel with Excellent Cryogenic Temperature Properties and Corresponding Constitutive Behaviour

Directory of Open Access Journals (Sweden)

Yuhui Wang

2018-02-01

Full Text Available A Fe-34.5 wt % Mn-0.04 wt % C ultra-high Mn steel with a fully recrystallised fine-grained structure was produced by cold rolling and subsequent annealing. The steel exhibited excellent cryogenic temperature properties with enhanced work hardening rate, high tensile strength, and high uniform elongation. In order to capture the unique mechanical behaviour, a constitutive model within finite strain plasticity framework based on Hill-type yield function was established with standard Armstrong-Frederick type isotropic hardening. In particular, the evolution of isotropic hardening was determined by the content of martensite; thus, a relationship between model parameters and martensite content is built explicitly.

High temperature (900-1300 C) mechanical behaviour of dendritic web grown silicon ribbons - Strain rate and temperature dependence of the yield stress

Science.gov (United States)

Mathews, V. K.; Gross, T. S.

1987-01-01

The mechanical behavior of dendritic web Si ribbons close the melting point was studied experimentally. The goal of the study was to generate data for modeling the generation of stresses and dislocation structures during growth of dendritic web Si ribbons, thereby permitting modifications to the production process, i.e., the temperature profile, to lower production costs for the photovoltaic ribbons. A laser was used to cut specimens in the direction of growth of sample ribbons, which were then subjected to tensile tests at temperatures up to 1300 C in an Ar atmosphere. The tensile strengths of the samples increased when the temperature rose above 1200 C, a phenomena which was attributed to the diffusion of oxygen atoms to the quasi-dislocation sites. The migration to the potential dislocations sites effectively locked the dislocations.

Micromechanical modelling of mechanical behaviour and strength of wood

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Qing, Hai

2008-01-01

An overview of the micromechanical theoretical and numerical models of wood is presented. Different methods of analysis of the effects of wood microstructures at different scale levels on the mechanical behaviour, deformation and strength of wood are discussed and compared. Micromechanical models...

Behavioural thermoregulation in a temperature-sensitive coral reef fish, the five-lined cardinalfish ( Cheilodipterus quinquelineatus)

Science.gov (United States)

Nay, Tiffany J.; Johansen, Jacob L.; Habary, Adam; Steffensen, John F.; Rummer, Jodie L.

2015-12-01

As global temperatures increase, fish populations at low latitudes are thought to be at risk as they are adapted to narrow temperature ranges and live at temperatures close to their thermal tolerance limits. Behavioural movements, based on a preference for a specific temperature ( T pref), may provide a strategy to cope with changing conditions. A temperature-sensitive coral reef cardinalfish ( Cheilodipterus quinquelineatus) was exposed to 28 °C (average at collection site) or 32 °C (predicted end-of-century) for 6 weeks. T pref was determined using a shuttlebox system, which allowed fish to behaviourally manipulate their thermal environment. Regardless of treatment temperature, fish preferred 29.5 ± 0.25 °C, approximating summer average temperatures in the wild. However, 32 °C fish moved more frequently to correct their thermal environment than 28 °C fish, and daytime movements were more frequent than night-time movements. Understanding temperature-mediated movements is imperative for predicting how ocean warming will influence coral reef species and distribution patterns.

Study on Mechanical and Physical Behaviour of Hybrid GFRP

Directory of Open Access Journals (Sweden)

Nor Bahiyah Baba

2015-01-01

Full Text Available The paper discusses the mechanical and physical behaviour of hybrid glass fibre reinforced plastic (GFRP. Hybrid GFRP was fabricated by three different types of glass fibre, namely, 3D, woven, and chopped, which were selected and combined with mixture of polyester resin and hardener. The hybrid GFRP was investigated by varying three parameters which were the composite volume fractions, hybrid GFRP arrangement, and single type fibre. The hybrid GFRP was fabricated by using open mould hand lay-up technique. Mechanical testing was conducted by tensile test for strength and stiffness whereas physical testing was performed using water absorption and hardness. These tests were carried out to determine the effect of mechanical and physical behaviour over the hybrid GFRP. The highest volume fraction of 0.5 gives the highest strength and stiffness of 73 MPa and 821 MPa, respectively. Varying hybrid fibre arrangement which is the arrangement of chopped-woven-3D-woven-chopped showed the best value in strength of 66.2 MPa. The stiffness is best at arrangement of woven-chopped-woven-chopped-woven at 690 MPa. This arrangement also showed the lowest water absorption of 4.5%. Comparing the single fibre type, woven had overtaken the others in terms of both mechanical and physical properties.

Open questions in the magnetic behaviour of high-temperature superconductors

International Nuclear Information System (INIS)

Cohen, L.F.; Jensen, Henrik Jeldtoft

1997-01-01

A principally experimental review of vortex behaviour in high-temperature superconductors is presented. The reader is first introduced to the basic concepts needed to understand the magnetic properties of type II superconductors. The concepts of vortex melting, the vortex glass, vortex creep, etc are also discussed briefly. The bulk part of the review relates the theoretical predictions proposed for the vortex system in high temperature superconductors to experimental findings. The review ends with an attempt to direct the reader to those areas which still require further clarification. (author)

Mathematical model of thermal and mechanical steady state fuel element behaviour TEDEF

International Nuclear Information System (INIS)

Dinic, N.; Kostic, Z.; Josipovic, M.

1987-01-01

In this paper a numerical model of thermal and thermomechanical behaviour of a cylindrical metal uranium fuel element is described. Presented are numerical method and computer program for solving the stationary temperature field and thermal stresses of a fuel element. The model development is a second phase of analysis of these phenomena, and may as well be used for analysing power nuclear reactor fuel elements behaviour. (author)

Material characterisation and preliminary mechanical design for the HL-LHC shielded beam screens operating at cryogenic temperatures.

Science.gov (United States)

Garion, C.; Dufay-Chanat, L.; Koettig, T.; Machiocha, W.; Morrone, M.

2015-12-01

The High Luminosity LHC project (HL-LHC) aims at increasing the luminosity (rate of collisions) in the Large Hadron Collider (LHC) experiments by a factor of 10 beyond the original design value (from 300 to 3000 fb-1). It relies on new superconducting magnets, installed close to the interaction points, equipped with new beam screen. This component has to ensure the vacuum performance together with shielding the cold mass from physics debris and screening the cold bore cryogenic system from beam induced heating. The beam screen operates in the range 40-60 K whereas the magnet cold bore temperature is 1.9 K. A tungsten-based material is used to absorb the energy of particles. In this paper, measurements of the mechanical and physical properties of such tungsten material are shown at room and cryogenic temperature. In addition, the design and the thermal mechanical behaviour of the beam screen assembly are presented also. They include the heat transfer from the tungsten absorbers to the cooling pipes and the supporting system that has to minimise the heat inleak into the cold mass. The behaviour during a magnet quench is also presented.

Material characterisation and preliminary mechanical design for the HL-LHC shielded beam screens operating at cryogenic temperatures

International Nuclear Information System (INIS)

Garion, C; Dufay-Chanat, L; Koettig, T; Machiocha, W; Morrone, M

2015-01-01

The High Luminosity LHC project (HL-LHC) aims at increasing the luminosity (rate of collisions) in the Large Hadron Collider (LHC) experiments by a factor of 10 beyond the original design value (from 300 to 3000 fb -1 ). It relies on new superconducting magnets, installed close to the interaction points, equipped with new beam screen. This component has to ensure the vacuum performance together with shielding the cold mass from physics debris and screening the cold bore cryogenic system from beam induced heating. The beam screen operates in the range 40-60 K whereas the magnet cold bore temperature is 1.9 K. A tungsten-based material is used to absorb the energy of particles. In this paper, measurements of the mechanical and physical properties of such tungsten material are shown at room and cryogenic temperature. In addition, the design and the thermal mechanical behaviour of the beam screen assembly are presented also. They include the heat transfer from the tungsten absorbers to the cooling pipes and the supporting system that has to minimise the heat inleak into the cold mass. The behaviour during a magnet quench is also presented. (paper)

The impact of the amount of polypropylene fibres on spalling behaviour and residual mechanical properties of Reactive Powder Concretes

Directory of Open Access Journals (Sweden)

Hager I.

2013-09-01

Full Text Available In this paper, an experimental study on the spalling behaviour and mechanical properties of Reactive Powder Concretes (RPCs in high temperature are presented. The research program was established to evaluate the impact of low melting temperature polypropylene fibres PP on mechanical properties evolution with temperature but also to verify the effectiveness of their addition to prevent spalling. Three sets of RPC specimens were prepared for this study with different amount of PP fibres (no fibres, 1.0 kg/m3 and 2.0 kg/m3. The addition of PP fibres reduces the initial compressive strength of the RPC material by approx. 14% no significant influence on modulus of elasticity was observed. Addition of 1 kg/m3 of PP fibres in RPC, seem not to give a sufficient protection against occurrence of spalling phenomenon. By adding 2 kg/m3 of PP fibres the risk of spalling is significantly reduced.

The effects of tantalum addition on the microtexture and mechanical behaviour of tungsten for ITER applications

International Nuclear Information System (INIS)

Tejado, E.; Carvalho, P.A.; Munoz, A.; Dias, M.; Correia, J.B.

2015-01-01

Tungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefore, many efforts have been made to improve its performance by alloying tungsten with other elements. Hence, in this investigation, the thermo-mechanical performance of two new tungsten-tantalum materials has been evaluated. Materials with W–5wt.%Ta and W–15wt.%Ta were processed by mechanical alloying (MA) and later consolidation by hot isostatic pressing (HIP), with distinct settings for each composition. Thus, it was possible to determine the relationship between the microstructure and the addition of Ta with the macroscopic mechanical properties. These were measured by means of hardness, flexural strength and fracture toughness, in the temperature range of 300–1473 K. The microstructure and the fracture surfaces features of the tested materials were analysed by Field Emission Scanning Electron Microscopy (FESEM).

The effects of tantalum addition on the microtexture and mechanical behaviour of tungsten for ITER applications

Energy Technology Data Exchange (ETDEWEB)

Tejado, E., E-mail: elena.tejado@mater.upm.es [Departamento de Ciencia de Materiales-CIME, ETSI Caminos, Canales y Puertos, Universidad Politécnica de Madrid, Madrid (Spain); Centro Nacional de Investigaciones Metalúrgicas (CSIC), Madrid (Spain); Carvalho, P.A. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); ICEMS, Departamento de Bioengenharia, Instituto Superior Técnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Munoz, A. [Departamento de Física, Universidad Carlos III, Leganés (Spain); Dias, M. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Correia, J.B. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Laboratório Nacional de Energia e Geologia, Estrada do Paço do Lumiar, 1649-038 Lisboa (Portugal); and others

2015-12-15

Tungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefore, many efforts have been made to improve its performance by alloying tungsten with other elements. Hence, in this investigation, the thermo-mechanical performance of two new tungsten-tantalum materials has been evaluated. Materials with W–5wt.%Ta and W–15wt.%Ta were processed by mechanical alloying (MA) and later consolidation by hot isostatic pressing (HIP), with distinct settings for each composition. Thus, it was possible to determine the relationship between the microstructure and the addition of Ta with the macroscopic mechanical properties. These were measured by means of hardness, flexural strength and fracture toughness, in the temperature range of 300–1473 K. The microstructure and the fracture surfaces features of the tested materials were analysed by Field Emission Scanning Electron Microscopy (FESEM).

Hot mechanical behaviour of dispersion strengthened Cu alloys

International Nuclear Information System (INIS)

Garcia G, Jose; Espinoza G, Rodrigo; Palma H, Rodrigo; Sepulveda O, Aquiles

2003-01-01

This work is part of a research project which objective is the improvement of the high-temperature mechanical properties of copper, without an important decrease of the electrical or thermal conduction properties. The general hypothesis is that this will be done by the incorporation of nanometric ceramic dispersoids for hindering the dislocation and grain boundaries movement. In this context, the object of the present work is the study of the resistance to hot deformation of dispersion-strengthened copper alloys which have prepared by reactive milling. Two different alloys, Cu-2,39wt.%Ti-0.56wt.%C and Cu-1.18wt.%Al, were prepared so as obtain a copper matrix reinforced with nanometric TiC y Al 2 O 3 particles with a nominal total amount of 5 vol.%. The particles were developed by an in-situ formation process during milling. The materials were prepared in an attritor mill, and consolidated by extrusion at 750 o C, with an area reduction rate of 10:1. The resistance to hot deformation was evaluated by hot compression tests at 500 and 850 o C, at initial strain rates of 10 -3 and 10 -4 s-1. To evaluate the material softening due temperature, annealing at 400, 650 y 900 o C during 1h were applied; after that, hardness was measured at room temperature. Both studies alloys presented a higher resistance to hot deformation than pure copper, with or without milling. Moreover, the Cu-Ti-C alloy presented a mechanical resistance higher than that of the Cu-Al one. Both alloys presented strain-stress compression curves with a typical hot-work shape: an initial maximum followed by a stationary plateau. The Cu-Ti-C alloy had a higher hardness and did not present a hardness decay even after annealings at the higher temperature imposed (900 o C), while the Cu-Al alloy did exhibit a strong decay of hardness after the annealing at 900 o C. The best behaviour exhibited by the Cu-Ti C alloy, was attributed to the formation of a major quantity of dispersoids that in the Cu-Al alloy. In

Exploring associations between self-regulatory mechanisms and neuropsychological functioning and driver behaviour after brain injury.

Science.gov (United States)

Rike, Per-Ola; Johansen, Hans J; Ulleberg, Pål; Lundqvist, Anna; Schanke, Anne-Kristine

2018-04-01

The objective of this prospective one-year follow-up study was to explore the associations between self-regulatory mechanisms and neuropsychological tests as well as baseline and follow-up ratings of driver behaviour. The participants were a cohort of subjects with stroke and traumatic brain injury (TBI) who were found fit to drive after a multi-disciplinary driver assessment (baseline). Baseline measures included neuropsychological tests and ratings of self-regulatory mechanisms, i.e., executive functions (Behavior Rating Inventory of Executive Function-Adult Version; BRIEF-A) and impulsive personality traits (UPPS Impulsive Behavior Scale). The participants rated pre-injury driving behaviour on the Driver Behaviour Qestionnaire (DBQ) retrospectively at baseline and after one year of post-injury driving (follow-up). Better performance on neuropsychological tests was significantly associated with more post-injury DBQ Violations. The BRIEF-A main indexes were significantly associated with baseline and follow-up ratings of DBQ Mistakes and follow-up DBQ Inattention. UPPS (lack of) Perseverance was significantly associated with baseline DBQ Inattention, whereas UPPS Urgency was significantly associated with baseline DBQ Inexperience and post-injury DBQ Mistakes. There were no significant changes in DBQ ratings from baseline (pre-injury) to follow-up (post-injury). It was concluded that neuropsychological functioning and self-regulatory mechanisms are related to driver behaviour. Some aspects of driver behaviour do not necessarily change after brain injury, reflecting the influence of premorbid driving behaviour or impaired awareness of deficits on post-injury driving behaviour. Further evidence is required to predict the role of self-regulatory mechanisms on driver behaviour and crashes or near misses.

Crack propagation behaviour in stainless steel AISI 316L at elevated temperatures under static and cyclic loading

International Nuclear Information System (INIS)

Lange, H.

1991-01-01

Experimental investigations of crack growth under creep and creep-fatigue conditions are presented. The experiments were performed with the austenitic steel AISI 316L, that will be used in fast breeder reactors. A comparison of crack propagation behaviour at temperatures of T = 550deg C and T = 700deg C in common through-thickness cracked specimens and in plates containing surface cracks is carried out by application of several fracture mechanics parameters. The quantitative description of crack initiation times and crack velocities is persued particularly. The propagation rate of one-dimensional cracks under cyclic loading conditions at T = 550deg C is also treated with fracture mechanical methods. The influence of the hold periods on crack speed is discussed. (orig.) [de

Mechanical behaviour of ferritic ODS steels - Temperature dependancy and history

Czech Academy of Sciences Publication Activity Database

Fournier, B.; Steckmeyer, A.; Rouffié, A.-L.; Malaplate, J.; Garnier, J.; Ratti, M.; Wident, P.; Ziolek, L.; Tournie, I.; Rabeau, V.; Gentzbittel, J.M.; Kruml, Tomáš; Kuběna, Ivo

2012-01-01

Roč. 430, 1-3 (2012), s. 142-149 ISSN 0022-3115 Institutional support: RVO:68081723 Keywords : ODS steels * fatigue * fracture mechanics Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 1.211, year: 2012

Properties and mechanical behaviour of fuel cans of fast neutron reactors

International Nuclear Information System (INIS)

Cauvin, R.; Boutard, J.L.

1983-06-01

Mechanical properties of Stainless steel-316 irradiated up to 100 dpa in fast neutron reactors are examined. Microscopic phenomena involved are reviewed: precipitation, segregation, dislocations, vacancies. Influence on mechanical behaviour of materials are examined: tensile properties, creep, ductility. Consequences on reactor dimensioning are given in conclusion [fr

Modeling of the mechanical behaviour of welded structures: behaviour laws and rupture criteria; Modelisation du comportement mecanique de structures soudees: lois de comportement et criteres de rupture

Energy Technology Data Exchange (ETDEWEB)

Paris, T.; Delaplanche, D. [CEA Valduc, Laboratoire Calcul et Simulations, 21120 Is-sur-Tille (France); Saanouni, K. [LASMIS-CNRS-FRE 2719, Universite de Technologie de Troyes BP 2060 - 10010 Troyes - (France)

2006-07-01

In the framework of the technological developments carried out in the CEA, the analysis of the mechanical behaviour of the heterogeneous welded bonds Ta/TA6V is a main preoccupation. Indeed, the welding of these two materials which cannot be distinguished by their mechanical and thermal properties induces strong microstructural heterogeneities in the melted zone. In order to characterize the behaviour of the welded joints and to develop a model of mechanical behaviour, a four points bending test on a notched specimen has been developed and implemented. This new test has allowed to obtain a macroscopic response of strength-displacement type but to analyze too more finely, with an optical extensometry and images correlation method, the influence of the heterogeneities on the local deformation of the welded joint. The confrontation of these results to a metallurgical study allows to validate the first conclusions deduced of the mechanical characterization tests and to conclude as for the local mechanisms governing the behaviour and the damage of the melted zone. The mechanical behaviour can be restored by an elasto-viscoplastic model with isotropic and non linear kinematic strain hardening coupled to this damage. The proposed model allows to identify the macroscopic behaviour of the weld bead. (O.M.)

Effect of heat treatment upon the mechanical and poro-mechanical behaviour of cement-based materials: hydraulic properties and morphological changes

International Nuclear Information System (INIS)

Chen, Xiao-Ting

2009-01-01

This work investigates the effects of morphological changes of a cement-based material subjected to heat treatment (up to 400 C). For a model W/C=0.5 mortar, we have characterized experimentally hydraulic behaviour (gas permeability), mechanical behaviour (in uniaxial compression, hydrostatic compression with or without deviatoric stress) and poro-mechanical behaviour (incompressibility moduli Kb, Ks and Biot's coefficient b) after a heating/cooling cycle. We have also developed an original experiment aimed at quantifying the accessible pore space volume under hydrostatic compression. The creation of occluded porosity under high confinement is confirmed, which justifies the observed decrease of solid matrix rigidity Ks under high confinement. A gas retention phenomenon was identified under simultaneous thermal and hydrostatic loadings for mortar, and industrial concretes (provided by CERIB and ANDRA). A predictive thermo-elasto-plastic model with isotropic damage and a micro-mechanical approach, which represents micro-cracking, are coupled in order to analyze or predict the evolution of mechanical and poro-elastic properties after heat cycling. (author)

Nanoscale strain-induced pair suppression as a vortex-pinning mechanism in high-temperature superconductors

International Nuclear Information System (INIS)

Llordes, Anna; Palau, A.; Gazquez, J.; Coll, M.; Vlad, R.; Pomar, A.; Arbiol, Jordi; Guzman, Roger; Ye, S.; Rouco, V.; Sandiumenge, Felip; Ricart, Susagna; Puig, Teresa; Varela del Arco, Maria; Chataigner, D.; Vanacken, J.; Gutierrez, J.; Moschalkov, V.; Deutscher, G.; Magen Dominguez, Cesar; Obradors, Xavier

2012-01-01

Boosting large-scale superconductor applications require nanostructured conductors with artificial pinning centres immobilizing quantized vortices at high temperature and magnetic fields. Here we demonstrate a highly effective mechanism of artificial pinning centers in solution-derived high-temperature superconductor nanocomposites through generation of nanostrained regions where Cooper pair formation is suppressed. The nanostrained regions identified from transmission electron microscopy devise a very high concentration of partial dislocations associated with intergrowths generated between the randomly oriented nanodots and the epitaxial YBa 2 Cu 3 O 7 matrix. Consequently, an outstanding vortex-pinning enhancement correlated to the nanostrain is demonstrated for four types of randomly oriented nanodot, and a unique evolution towards an isotropic vortex-pinning behaviour, even in the effective anisotropy, is achieved as the nanostrain turns isotropic. We suggest a new vortex-pinning mechanism based on the bond-contraction pairing model, where pair formation is quenched under tensile strain, forming new and effective core-pinning regions.

Thermal and mechanical behaviour of an experimental mock-up of a nuclear containment; Comportement thermique et mecanique d'une maquette experimentale d'enceinte de confinement nucleaire

Energy Technology Data Exchange (ETDEWEB)

Chauvel, D. [Electricite de France (EDF/SEPTEN), 69 - Villeurbanne (France); Barre, F. [Coyne et Bellier, 92 - Gennevilliers (France)

2007-07-01

In order to better understand the behaviour of a reactor containment submitted to combined pressure and temperature loads by means of studies of the concrete permeability and the state of cracking evolution, EDF and its French partners have built a prestressed concrete test model which represents a PWR containment typical section. The monitoring system was designed to follow the evolution of strains, temperature and state of cracking of the concrete wall from construction stage to air and steam tests. The measurements results as well as their comparison with theoretical laws or data and calculated values, allow to determine the main thermal and mechanical characteristics of the concrete, to analyse the thermo-mechanical behaviour of the structure and also to check the design criteria of prestressed concrete containments. (authors)

Believing versus interacting: Behavioural and neural mechanisms underlying interpersonal coordination

DEFF Research Database (Denmark)

Konvalinka, Ivana; Bauer, Markus; Kilner, James

When two people engage in a bidirectional interaction with each other, they use both bottom-up sensorimotor mechanisms such as monitoring and adapting to the behaviour of the other, as well as top-down cognitive processes, modulating their beliefs and allowing them to make decisions. Most research...... in joint action has investigated only one of these mechanisms at a time – low-level processes underlying joint coordination, or high-level cognitive mechanisms that give insight into how people think about another. In real interactions, interplay between these two mechanisms modulates how we interact...

Experimental study and modelling of the high temperature mechanical behavior of oxide dispersion strengthened ferritic steels

International Nuclear Information System (INIS)

Steckmeyer, A.

2012-01-01

The strength of metals, and therefore their maximum operating temperature, can be improved by oxide dispersion strengthening (ODS). Numerous research studies are carried out at the French Atomic Energy Commission (CEA) in order to develop a cladding tube material for Gen IV nuclear power reactors. Oxide dispersion strengthened steels appear to be the most promising candidates for such application, which demands a minimum operating temperature of 650 C. The present dissertation intends to improve the understanding of the mechanical properties of ODS steels, in terms of creep lifetime and mechanical anisotropy. The methodology of this work includes mechanical tests between room temperature and 900 C as well as macroscopic and polycrystalline modelling. These tests are carried out on a Fe-14Cr1W0,26Ti + 0,3 Y 2 O 3 ODS ferritic steel processed at CEA by mechanical alloying and hot extrusion. The as-received material is a bar with a circular section. The mechanical tests reveal the high mechanical strength of this steel at high temperature. A strong influence of the strain rate on the ductility and the mechanical strength is also observed. A macroscopic mechanical model has been developed on the basis of some experimental statements such as the high kinematic contribution to the flow stress. This model has a strong ability to reproduce the mechanical behaviour of the studied material. Two different polycrystalline models have also been developed in order to reproduce the mechanical anisotropy of the material. They are based on its specific grain morphology and crystallographic texture. The discrepancy between the predictions of both models and experimental results reveal the necessity to formulate alternate assumptions on the deformation mechanisms of ODS ferritic steels. (author) [fr

Effect of coating mild steel with CNTs on its mechanical properties and corrosion behaviour in acidic medium

Science.gov (United States)

Abdulmalik Abdulrahaman, Mahmud; Kamaldeeen Abubakre, Oladiran; Ambali Abdulkareem, Saka; Oladejo Tijani, Jimoh; Aliyu, Ahmed; Afolabi, Ayo Samuel

2017-03-01

The study investigated the mechanical properties and corrosion behaviour of mild steel coated with carbon nanotubes at different coating conditions. Multi-walled carbon nanotubes (MWCNTs) were synthesized via the conventional chemical vapour deposition reaction using bimetallic Fe-Ni catalyst supported on kaolin, with acetylene gas as a carbon source. The HRSEM/HRTEM analysis of the purified carbon materials revealed significant reduction in the diameters of the purified MWCNT bundles from 50 nm to 2 nm and was attributed to the ultrasonication assisted dispersion with surfactant (gum arabic) employed in purification process. The network of the dispersed MWCNTs was coated onto the surfaces of mild steel samples, and as the coating temperature and holding time increased, the coating thickness reduced. The mechanical properties (tensile strength, yield strength, hardness value) of the coated steel samples increased with increase in coating temperature and holding time. Comparing the different coating conditions, coated mild steels at the temperature of 950 °C for 90 min holding time exhibited high hardness, yield strength and tensile strength values compared to others. The corrosion current and corrosion rate of the coated mild steel samples decreased with increase in holding time and coating temperature. The lowest corrosion rate was observed on sample coated at 950 °C for 90 min.

Temperature sensitive self-actuated scram mechanism

International Nuclear Information System (INIS)

Giuggio, N.; Noyes, R.C.; Zaman, S.U.

1982-01-01

This invention provides a mechanism for rapidly dropping a neutron absorbing poison material into the core of an LMFBR type reactor, and in particular a mechanism that is self-actuated when the reactor coolant temperature reaches a critical value. A safety duct located in the reactor core and extending above the core contains an inner column that provides a vertical coolant flow path through the duct. One or more fuel pins are located in the duct, with a temperature-responsive actuator near their upper ends. A poison bundle surrounds the inner column within the duct, held in position by a release mechanism connected to the actuator. The inferred core temperature is sensed by a fluid confined within the actuator, and the expansion of the fluid is translated into a linear force used to activate the release mechanism

Characterization techniques to predict mechanical behaviour of green ceramic bodies fabricated by ceramic microstereolithography

Science.gov (United States)

Adake, Chandrashekhar V.; Bhargava, Parag; Gandhi, Prasanna

2018-02-01

Ceramic microstereolithography (CMSL) has emerged as solid free form (SFF) fabrication technology in which complex ceramic parts are fabricated from ceramic suspensions which are formulated by dispersing ceramic particles in UV curable resins. Ceramic parts are fabricated by exposing ceramic suspension to computer controlled UV light which polymerizes resin to polymer and this polymer forms rigid network around ceramic particles. A 3-dimensional part is created by piling cured layers one over the other. These ceramic parts are used to build microelectromechanical (MEMS) devices after thermal treatment. In many cases green ceramic parts can be directly utilized to build MEMS devices. Hence characterization of these parts is essential in terms of their mechanical behaviour prior to their use in MEMS devices. Mechanical behaviour of these green ceramic parts depends on cross link density which in turn depends on chemical structure of monomer, concentrations of photoinitiator and UV energy dose. Mechanical behaviour can be determined with the aid of nanoindentation. And extent of crosslinking can be verified with the aid of DSC. FTIR characterization is used to analyse (-C=C-) double bond conversion. This paper explains characterization tools to predict the mechanical behaviour of green ceramic bodies fabricated in CMSL

Modelled temperature-dependent excitability behaviour of a generalised human peripheral sensory nerve fibre.

Science.gov (United States)

Smit, Jacoba E; Hanekom, Tania; Hanekom, Johan J

2009-08-01

The objective of this study was to determine if a recently developed human Ranvier node model, which is based on a modified version of the Hodgkin-Huxley model, could predict the excitability behaviour in human peripheral sensory nerve fibres with diameters ranging from 5.0 to 15.0 microm. The Ranvier node model was extended to include a persistent sodium current and was incorporated into a generalised single cable nerve fibre model. Parameter temperature dependence was included. All calculations were performed in Matlab. Sensory nerve fibre excitability behaviour characteristics predicted by the new nerve fibre model at different temperatures and fibre diameters compared well with measured data. Absolute refractory periods deviated from measured data, while relative refractory periods were similar to measured data. Conduction velocities showed both fibre diameter and temperature dependence and were underestimated in fibres thinner than 12.5 microm. Calculated strength-duration time constants ranged from 128.5 to 183.0 micros at 37 degrees C over the studied nerve fibre diameter range, with chronaxie times about 30% shorter than strength-duration time constants. Chronaxie times exhibited temperature dependence, with values overestimated by a factor 5 at temperatures lower than body temperature. Possible explanations include the deviated absolute refractory period trend and inclusion of a nodal strangulation relationship.

The influence of water on the mechanical behaviour of argillaceous rocks

International Nuclear Information System (INIS)

Freissmuth, H.J.

2002-12-01

This thesis was done in collaboration with the French national radioactive waste agency ANDRA. The aim is to contribute to a better understanding of the mechanical behaviour of argillaceous rocks under the influence of aqueous solutions, as they are considered to be a possible host rock for a nuclear waste disposal site. Shale, can depending on the composition, change its mechanical and petrophysical properties in a wide range due to fluid-clay mineral interactions. One and the same shale can be soft or hard, ductile or rigid, permeable or sealing - depending on the environmental conditions the sample is exposed to. Shale can be very sensitive to a change of conditions such as humidity, stress state, temperature, and chemical potential gradients. One of the most obvious shale reactions is the swelling and shrinking as a function of it's saturation and the chemical potential gradient in the fluid system. Theses volume changes also sometimes alter other properties. Depending on the nature and the concentration of a liquid, a shale can either shrink or swell when in contact with a liquid. The material may sometimes also disperse in the liquid and deteriorate completely.An understandable description of the clay-minerals from the site of Est is given. The physicochemical micro mechanism of the fluid solid interaction such as adsorption, absorption, capillarity and osmosis are also presented. The possible consequences of these mechanisms on the macro mechanical behaviour, such as swelling and shrinking, crack induction and others was analysed. X-ray microfocus technology was introduced and used to analyse shale under different environmental conditions. The advantage of this technology is it's non-destructive character. The preparation of classical thin cross section is a rather inappropriate method, concerning micro cracks and deterioration in shale, because of the grinding of the material. A solution test was conducted to qualitatively observe the real-time reaction of

The role of urgency and its underlying psychological mechanisms in problematic behaviours.

Science.gov (United States)

Billieux, Joël; Gay, Philippe; Rochat, Lucien; Van der Linden, Martial

2010-11-01

The urgency facet of impulsivity, that is, the tendency to act rashly in response to intense emotional contexts [Cyders, M. A., & Smith, G. T. (2008). Emotion-based dispositions to rash action: positive and negative urgency. Psychological Bulletin, 134, 807-828], has been related to a wide range of maladaptive behaviours. The present study further investigates the role of urgency in problematic behaviours by considering distinct psychological mechanisms that may underlie this component of impulsivity. With this aim, 95 volunteer participants were screened with self-reported questionnaires assessing urgency and three problematic behaviours (compulsive buying, excessive mobile phone use, excessive Internet use). They performed two laboratory tasks: a stop-signal task designed to assess the capacity to inhibit prepotent responses in response to both neutral and emotional stimuli; and the Iowa Gambling Task (IGT) measuring the ability to take into account the future consequences of an action. A poor ability to inhibit prepotent responses in the emotional condition of the stop-signal task was found to predict more disadvantageous choices in the IGT, which ultimately results in higher urgency and more problematic behaviours. These findings shed new light on the construct of urgency, its related psychological mechanisms, and its role in problematic behaviours. Copyright © 2010 Elsevier Ltd. All rights reserved.

Dislocation mechanisms for plastic flow of nickel in the temperature range 4.2-1200K

International Nuclear Information System (INIS)

Sastry, D.H.; Tangri, K.

1975-01-01

The temperature ranges of thermal and athermal deformation behaviour of nickel are identified by employing the temperature-dependence of flow-stress and strain-rate cycling data. The results are used to present a unified view of dislocation mechanisms of glide encompassing the two thermally activated and the intermediate athermal regimes of plastic flow. In the low-temperature thermally activated region (<250K) the strain rate is found to be controlled by the repulsive intersection of glide and forest dislocations, in accordance with current ideas. The athermal stress in this region can be attributed mainly to the presence of strong attractive junctions which are overcome by means of Orowan bowing, a small contribution also coming from the elastic interactions between dislocations. The values of activation area and activation energy obtained in the high-temperature region (<750K) negate the operation of a diffusion-controlled mechanism. Instead, the data support a thermal activation model involving unzipping of the attractive junctions. The internal (long-range) stress contribution here results solely from the elastic interactions between dislocations. This view concerning the high-temperature plastic flow is further supported by the observation that the Cottrell-Stokes law is obeyed over large strains in the range 750-1200K. (author)

Mechanism governing nanoparticle flow behaviour in porous media: insight for enhanced oil recovery applications

Science.gov (United States)

Agi, Augustine; Junin, Radzuan; Gbadamosi, Afeez

2018-06-01

Nanotechnology has found its way to petroleum engineering, it is well-accepted path in the oil and gas industry to recover more oil trapped in the reservoir. But the addition of nanoparticles to a liquid can result in the simplest flow becoming complex. To understand the working mechanism, there is a need to study the flow behaviour of these particles. This review highlights the mechanism affecting the flow of nanoparticles in porous media as it relates to enhanced oil recovery. The discussion focuses on chemical-enhanced oil recovery, a review on laboratory experiment on wettability alteration, effect of interfacial tension and the stability of emulsion and foam is discussed. The flow behaviour of nanoparticles in porous media was discussed laying emphasis on the physical aspect of the flow, the microscopic rheological behaviour and the adsorption of the nanoparticles. It was observed that nanofluids exhibit Newtonian behaviour at low shear rate and non-Newtonian behaviour at high shear rate. Gravitational and capillary forces are responsible for the shift in wettability from oil-wet to water-wet. The dominant mechanisms of foam flow process were lamellae division and bubble to multiple bubble lamellae division. In a water-wet system, the dominant mechanism of flow process and residual oil mobilization are lamellae division and emulsification, respectively. Whereas in an oil-wet system, the generation of pre-spinning continuous gas foam was the dominant mechanism. The literature review on oil displacement test and field trials indicates that nanoparticles can recover additional oil. The challenges encountered have opened new frontier for research and are highlighted herein.

Extended exposure to elevated temperature affects escape response behaviour in coral reef fishes

Directory of Open Access Journals (Sweden)

Donald T. Warren

2017-08-01

Full Text Available The threat of predation, and the prey’s response, are important drivers of community dynamics. Yet environmental temperature can have a significant effect on predation avoidance techniques such as fast-start performance observed in marine fishes. While it is known that temperature increases can influence performance and behaviour in the short-term, little is known about how species respond to extended exposure during development. We produced a startle response in two species of damselfish, the lemon damsel Pomacentrus moluccensis, and the Ambon damselfish Pomacentrus amboinensis, by the repeated use of a drop stimulus. We show that the length of thermal exposure of juveniles to elevated temperature significantly affects this escape responses. Short-term (4d exposure to warmer temperature affected directionality and responsiveness for both species. After long-term (90d exposure, only P. moluccensis showed beneficial plasticity, with directionality returning to control levels. Responsiveness also decreased in both species, possibly to compensate for higher temperatures. There was no effect of temperature or length of exposure on latency to react, maximum swimming speed, or escape distance suggesting that the physical ability to escape was maintained. Evidence suggests that elevated temperature may impact some fish species through its effect on the behavioural responses while under threat rather than having a direct influence on their physical ability to perform an effective escape response.

High temperature tribological behaviour of carbon based (B{sub 4}C and DLC) coatings in sliding contact with aluminum

Energy Technology Data Exchange (ETDEWEB)

Gharam, A. Abou, E-mail: abougha@uwindsor.c [Mechanical Automotive and Materials Engineering Department, University of Windsor, Windsor, ON, N9B3P4 (Canada); Lukitsch, M.J.; Balogh, M.P. [Chemical Sciences and Materials Systems Laboratory, General Motors R and D Center, 30500 Mound Road, Warren, MI 48090-9055 (United States); Alpas, A.T. [Mechanical Automotive and Materials Engineering Department, University of Windsor, Windsor, ON, N9B3P4 (Canada)

2010-12-30

Carbon based coatings, particularly diamond-like carbon (DLC) films are known to resist aluminum adhesion and reduce friction at room temperature. This attractive tribological behaviour is useful for applications such as tool coatings used for aluminum forming and machining. However, for those operations that are performed at elevated temperatures (e.g. hot forming) or that generate frictional heat during contact (e.g. dry machining) the suitable coatings are required to maintain their tribological properties at high temperatures. Candidates for these demanding applications include boron carbide (B{sub 4}C) and DLC coatings. An understanding of the mechanisms of friction, wear and adhesion of carbon based coatings against aluminum alloys at high temperatures will help in designing coatings with improved high temperature tribological properties. With this goal in mind, this study focused on B{sub 4}C and a hydrogenated DLC coatings sliding against a 319 grade cast aluminum alloy by performing pin-on-disk experiments at temperatures up to 400 {sup o}C. Experimental results have shown that the 319 Al/B{sub 4}C tribosystem generated coefficient of friction (COF) values ranging between 0.42 and 0.65, in this temperature range. However, increased amounts of aluminum adhesion were detected in the B{sub 4}C wear tracks at elevated temperatures. Focused ion beam (FIB) milled cross sections of the wear tracks revealed that the coating failed due to shearing along the columnar grain boundaries of the coating. The 319 Al/DLC tribosystem maintained a low COF (0.15-0.06) from room temperature up to 200 {sup o}C. This was followed by an abrupt increase to 0.6 at 400 {sup o}C. The deterioration of friction behaviour at T > 200 {sup o}C was attributed to the exhaustion of hydrogen and hydroxyl passivants on the carbon transfer layer formed on the Al pin.

Thermodynamic behaviour of ruthenium at high temperatures

International Nuclear Information System (INIS)

Garisto, F.

1988-01-01

Thermodynamic equilibrium calculations are used to determine the chemical speciation of ruthenium under postulated reactor accident conditions. The speciation of ruthenium is determined for various values of temperature, pressure, oxygen partial pressure and ruthenium concentration. The importance of these variables, in particular the oxygen partial pressure, in determining the volatility of ruthenium is clearly demonstrated in this report. Reliable thermodynamic data are required to determine the behaviour of ruthenium using equilibrium calculations. Therefore, it was necessary to compile a thermodynamic database for the ruthenium species that can be formed under reactor accident conditions. The origin of the thermodynamic data for the ruthenium species included in our calculations is discussed in detail in Appendix A. 23 refs

Characterisation of material behaviour in high temperature aqueous environments by means of electrochemical techniques

International Nuclear Information System (INIS)

Bojinov, M.; Laitinen, T.; Maekelae, K.; Sirkiae, P.; Beverskog, B.

1998-01-01

Electrochemical measurements in solutions simulating power plant coolants are complicated by the low conductivity of the water, especially in the case of boiling water reactor (BWR) environments. To be able to obtain useful information also in BWR conditions, electrochemical techniques based on a thin-layer electrode arrangement are introduced. This arrangement makes it possible to perform voltammetric and electrochemical impedance measurements in high-temperature water with a room temperature conductivity (κ) as low as 0.1 μScm -1 . A combination of these results with those obtained by means of measuring the resistance of the surface film using the contact electric resistance (CER) technique facilitates versatile characterisation of oxide film behaviour. Examples are given on impedance and CER measurements of the oxide films formed on AISI 316 stainless steel in high temperature high purity (κ -1 ) water and on OX18H10T stainless steel in VVER water. Correlations between temperature, hydrogen and oxygen content of the solution and the oxide behaviour are discussed. (author)

Density-dependent hydro-mechanical behaviour of a compacted expansive soil

International Nuclear Information System (INIS)

NOWAMOOZ, Hossein; MASROURI, Farimah

2010-01-01

Document available in extended abstract form only. Clayey soils are widely used in geotechnical engineering for dam cores, barriers in waste landfills and for engineered barriers in nuclear waste storage facilities. In the latter case, the used materials contain a large amount of smectite which is a highly swelling clay. On site, they can be submitted to complex suction/ stress/temperature variations that could change dramatically their hydro-mechanical behavior, meaning their saturated and unsaturated mechanical characteristics. To further our knowledge of the coupling between the hydraulic and mechanical behaviour of the swelling soils, this paper presents an experimental study on a swelling bentonite/silt mixture using osmotic odometers. A loading/unloading cycle was applied to samples with different initial dry densities (1.27, 1.48, and 1.55 Mg.m -3 ) at different constant suctions (0, 2, and 8 MPa). These experimental results provided a sufficient database to analytically model the mechanical behavior of the swelling soil and define three yielding surfaces: - the Suction Limit between Micro- and Macrostructure (s m/M ) and the Suction Limit between Nano- and Microstructure (s n/m ), which depend completely on the soil fabrics and the diameter separating the nano-, micro-, and macrostructure, - the Loading Collapse (LC) curve, representing the pre-consolidation stress variation as a function of suction, - the Saturation Curve (SC), representing the variation of the saturation stress (P sat ) as a function of suction. In general, we can state that the increase of compaction pressure unified the LC and SC surfaces and decreased the (s m/M ) value without modifying the (s n/m ) value. (authors)

COMETHE III J a computer code for predicting mechanical and thermal behaviour of a fuel pin

International Nuclear Information System (INIS)

Verbeek, P.; Hoppe, N.

1976-01-01

The design of fuel pins for power reactors requires a realistic evaluation of their thermal and mechanical performances throughout their irradiation life. This evaluation involves the knowledge of a number of parameters, very intricate and interconnected, for example, the temperature, the restructuring and the swelling rates of the fuel pellets, the dimensions, the stresses and the strains in the clad, the composition and the properties of gases, the inner gas pressure etc. This complex problem can only be properly handled by a computer programme which analyses the fuel pin thermal and mechanical behaviour at successive steps of its irradiation life. This report presents an overall description of the COMETHE III-J computer programme, designed to calculate the integral performance of oxide fuel pins with cylindrical metallic cladding irradiated in thermal or fast flux. (author)

Nanoscale grain growth behaviour of CoAl intermetallic synthesized ...

Indian Academy of Sciences (India)

Grain growth behaviour of the nanocrystalline CoAl intermetallic compound synthesized by mechanical alloying has been studied by isothermal annealing at different temperatures and durations. X-ray diffraction method was employed to investigate structural evolutions during mechanical alloying and annealing processes.

Nanoscale grain growth behaviour of CoAl intermetallic synthesized ...

Indian Academy of Sciences (India)

Administrator

Abstract. Grain growth behaviour of the nanocrystalline CoAl intermetallic compound synthesized by mechanical alloying has been studied by isothermal annealing at different temperatures and durations. X-ray diffraction method was employed to investigate structural evolutions during mechanical alloying and anneal-.

Oscillatory behaviour of catalytic properties, structure and temperature during the catalytic partial oxidation of methane on Pd/Al2O3

DEFF Research Database (Denmark)

Kimmerle, B.; Baiker, A.; Grunwaldt, Jan-Dierk

2010-01-01

Pd/Al2O3 catalysts showed an oscillatory behaviour during the catalytic partial oxidation (CPO) of methane, which was investigated simultaneously by IR-thermography, X-ray absorption spectroscopy, and online mass-spectrometry to correlate the temperature, state of the catalyst and catalytic...... to self-reduction leading to extinction of the process. The latter was the key driver for the oscillations and thus gave additional insight into the mechanism of partial methane oxidation....

Tritium adsorption/release behaviour of advanced EU breeder pebbles

Science.gov (United States)

Kolb, Matthias H. H.; Rolli, Rolf; Knitter, Regina

2017-06-01

The tritium loading of current grades of advanced ceramic breeder pebbles with three different lithium orthosilicate (LOS)/lithium metatitanate (LMT) compositions (20-30 mol% LMT in LOS) and pebbles of EU reference material, was performed in a consistent way. The temperature dependent release of the introduced tritium was subsequently investigated by temperature programmed desorption (TPD) experiments to gain insight into the desorption characteristics. The obtained TPD data was decomposed into individual release mechanisms according to well-established desorption kinetics. The analysis showed that the pebble composition of the tested samples does not severely change the release behaviour. Yet, an increased content of lithium metatitanate leads to additional desorption peaks at medium temperatures. The majority of tritium is released by high temperature release mechanisms of chemisorbed tritium, while the release of physisorbed tritium is marginal in comparison. The results allow valuable projections for the tritium release behaviour in a fusion blanket.

Inheritance of nesting behaviour across natural environmental variation in a turtle with temperature-dependent sex determination.

Science.gov (United States)

McGaugh, Suzanne E; Schwanz, Lisa E; Bowden, Rachel M; Gonzalez, Julie E; Janzen, Fredric J

2010-04-22

Nesting behaviour is critical for reproductive success in oviparous organisms with no parental care. In organisms where sex is determined by incubation temperature, nesting behaviour may be a prime target of selection in response to unbalanced sex ratios. To produce an evolutionary change in response to sex-ratio selection, components of nesting behaviour must be heritable. We estimated the field heritability of two key components of nesting behaviour in a population of painted turtles (Chrysemys picta) with temperature-dependent sex determination by applying the 'animal model' to a pedigree reconstructed from genotype data. We obtained estimates of low to non-detectable heritability using repeated records across all environments. We then determined environment-specific heritability by grouping records with similar temperatures for the winter preceding the nesting season, a variable known to be highly associated with our two traits of interest, nest vegetation cover and Julian date of nesting. The heritability estimates of nest vegetation cover and Julian date of nesting were qualitatively highest and significant, or nearly so, after hot winters. Additive genetic variance for these traits was not detectable after cold winters. Our analysis suggests that the potential for evolutionary change of nesting behaviour may be dependent on the thermal conditions of the preceding winter, a season that is predicted to be especially subject to climate change.

Mechanical Behaviour of Sisal Fibre Reinforced Cement Composites

OpenAIRE

M. Aruna

2014-01-01

Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. ...

Mechanical pumping at low temperature

International Nuclear Information System (INIS)

Perin, J.P.; Claudet, G.; Disdier, F.

1995-01-01

This novel concept consist of a mechanical pump able to run at low temperature (25K). Since gas density varies inversely with temperature, this pump would deliver much higher mass flow rate than at room temperature for a given size. Advantages of this concept are order of magnitude reduction in size, weight, when compared to a conventional pump scaled to perform the same mass flow rate at room temperature. This pump would be a solution to allow continuously tritium extraction and minimize the mass inventory. (orig.)

General presentation of the core mechanical behaviour approach in France

International Nuclear Information System (INIS)

Bernard, A.; Dorsselaere, J.P. van

1984-01-01

This French review paper presents the evolution along time of the FBR core mechanical behaviour approach, from RAPSODIE to SPX2, through PHENIX and SPX1: core designs, knowledge of the irradiation laws, project criterias, calculation codes, and R and D fields. (author)

The effects of temperature and strain rate on the dynamic flow behaviour of different steels

International Nuclear Information System (INIS)

Lee, W.-S.; Liu, C.-Y.

2006-01-01

A compressive type split-Hopkinson pressure bar is utilized to compare the impact plastic behaviour of three steels with different levels of carbon content. S15C low carbon steel, S50C medium alloy heat treatable steel (abbreviated hereafter to medium carbon steel) and SKS93 tool steel with a high carbon and low alloy content (abbreviated hereafter to high carbon steel) are tested under strain rates ranging from 1.1 x 10 3 s -1 to 5.5 x 10 3 s -1 and temperatures ranging from 25 to 800 deg. C. The effects of the carbon content, strain rate and temperature on the mechanical responses of the three steels are evaluated. The microstructures of the impacted specimens are studied using a transmission electron microscope (TEM). It is found that an increased carbon content enhances the dynamic flow resistance of the three steels. Additionally, the flow stress increases with strain and strain rate in every case. A thermal softening effect is identified in the plastic behaviour of the three steels. The activation energy, ΔG * , varies as a function of the strain rate and temperature, but is apparently insensitive to the carbon content level. The present study identifies maximum ΔG * values of 58 kJ/mol for the S15C low carbon steel, 54.9 kJ/mol for the S50C medium carbon steel, and 56.4 kJ/mol for the SKS93 high carbon steel. A Zerilli-Armstrong BCC constitutive model with appropriate coefficients is applied to describe the high strain rate plastic behaviours of the S15C, S50C and SKS93 steels. The errors between the calculated stress and the measured stress are found to be less than 5%. The microstructural observations reveal that the dislocation density and the degree of dislocation tangling increase with increasing strain rate in all three steels. Additionally, the TEM observations indicate that a higher strain rate reduces the size of the dislocation cells. The annihilation of dislocations occurs more readily at elevated temperatures. The square root of the dislocation

Influence of the outlet air temperature on the thermohydraulic behaviour of air coolers

Directory of Open Access Journals (Sweden)

Đorđević Emila M.

2003-01-01

Full Text Available The determination of the optimal process conditions for the operation of air coolers demands a detailed analysis of their thermohydraulic behaviour on the one hand, and the estimation of the operating costs, on the other. One of the main parameters of the thermohydraulic behaviour of this type of equipment, is the outlet air temperature. The influence of the outlet air temperature on the performance of air coolers (heat transfer coefficient overall heat transfer coefficient, required surface area for heat transfer air-side pressure drop, fan power consumption and sound pressure level was investigated in this study. All the computations, using AirCooler software [1], were applied to cooling of the process fluid and the condensation of a multicomponent vapour mixture on two industrial devices of known geometries.

Physical and mechanical behaviour of a roller compacted concrete ...

African Journals Online (AJOL)

In order to study the behaviour of a roller compacted concrete (RCC) reinforced with polypropylene fiber, six types of RCC were made with different content of fibers (0, 0.5, 1, 1.5, 2 and 2.5 Kg/m3). The physical parameters are the density, the workability, the shrinkage and the water absorption. For the mechanical ...

Elevated temperature fracture mechanics

International Nuclear Information System (INIS)

Tomkins, B.

1979-01-01

The application of fracture mechanics concepts to cracks at elevated temperatures is examined. Particular consideration is given to the characterisation of crack tip stress-strain fields and parameters controlling crack extension under static and cyclic loads. (author)

Simplified methods applied to the complete thermal and mechanical behaviour of a pressure vessel during a severe accident

International Nuclear Information System (INIS)

Dupas, P.

1996-01-01

EDF has developed a software package of simplified methods (proprietary ones from literature) in order to study the thermal and mechanical behaviour of a PWR pressure vessel during a severe accident involving a corium localization in the vessel lower head. Using a part of this package, we can evaluate for instance successively: the heat flux at the inner surface of the vessel (conductive or convective pool of corium); the thermal exchange coefficient between the vessel and the outside (dry pit or flooded pit, watertight thermal insulation or not); the complete thermal evolution of the vessel (temperature profile, melting); the possible global plastic failure of the vessel; the creep behaviour in the vessel. These simplified methods are low cost alternative to finite element calculations which are yet used to validate the previous methods, waiting for experimental results to come. (authors)

Design and fabrication of a cryostat for low temperature mechanical testing for the Mechanical and Materials Engineering group at CERN

CERN Document Server

Aviles Santillana, I; Gerardin, A; Guinchard, M; Langeslag, S A E; Sgobba, S

2015-01-01

Mechanical testing of materials at low temperatures is one of the cornerstones of the Mechanical and Materials Engineering (MME) group at CERN. A long tradition of more than 20 years and a unique know - how of such tests has been developed with an 18 kN double-walled cryostat. Large campaigns of material qualification have been carried out and the mechanical behaviour of materials at 4 K has been vastly studied in sub - size samples for projects like LEP, LHC and its experiments. With the aim of assessing the mechanical properties of materials of higher strength and/or issued from heavy gauge products for which testing standardized specimens of larger cross section might be more adapted, a new 100 kN cryostat capable of hosting different shapes of normalized samples has been carefully designed and fabricated inhouse together with the associated tooling and measurement instrumentation. It has been conceived to be able to adapt to different test frames both dynamic and static, which will be of paramount importa...

Mechanical behaviour of adhesive joint under tensile and shear loading

NARCIS (Netherlands)

Jiang, X.; Kolstein, M.H.; Bijlaard, F.S.K.

2013-01-01

Due to various advantages of Fibre-Reinforced Polymer (FRP) decks, the FRP to steel composite bridge system is being increasingly used in new bridge structures as well as rehabilitation projects for old bridges. This paper focuses on the mechanical behaviours and failure modes of the

Mechanical behaviour of PEM fuel cell catalyst layers during regular cell operation

OpenAIRE

Maher A.R. Sadiq Al-Baghdadi

2010-01-01

Damage mechanisms in a proton exchange membrane fuel cell are accelerated by mechanical stresses arising during fuel cell assembly (bolt assembling), and the stresses arise during fuel cell running, because it consists of the materials with different thermal expansion and swelling coefficients. Therefore, in order to acquire a complete understanding of the mechanical behaviour of the catalyst layers during regular cell operation, mechanical response under steady-state hygro-thermal stresses s...

Temperature and heat effects on polyethylene behaviour in the presence of imperfections

Directory of Open Access Journals (Sweden)

Murariu Alin Constantin

2016-01-01

Full Text Available This paper highlights the changes of polyethylene behaviour during various loading rate as well as the influence of test temperature on the material characteristics. Passive infrared thermography (IRT method and a high speed infrared camera were used to observe the temperature changes of the sample surface during the tests. The experimental program was carried out on samples taken from PE80 polyethylene gas pipes with simulated imperfections with bilateral V-notch, U-notch and central hole. Samples have been tensile tested (TT and the results are correlated with the temperature distribution of the samples surface.

Stress Corrosion Cracking of alloy 600 in high temperature water: a study of mechanisms

International Nuclear Information System (INIS)

Boursier, J.M.; Bouvier, O. de; Gras, J.M.; Noel, D.; Vaillant, F.; Rios, R.

1992-12-01

Investigations of the stress corrosion cracking behaviour of Alloy 600 tubing in high temperature water were performed in order to get a precise knowledge of the different stages of the cracking and their dependence on various parameters. The compatibility of the results with the main mechanisms to be considered was examined. Results showed three stages in the cracking: a true incubation time, a slow-rate propagation period followed by a rapid-propagation stage. Tests separating stress and strain rate contributions show that the strain rate is the main parameter which controls the crack propagation. The hydrogen overpressure was found to increase the crack growth rate up to 1-4 bar, but a strong decrease is observed from 4 to 20 bar. Analysis of the hydrogen ingress in the metal showed that it is neither correlated to the hydrogen overpressure nor to the severity of cracking; so cracking resulting from an hydrogen-model is unlikely. No detrimental effect of oxygen (4 bar) was noticed both in the mill-annealed and the sensitized conditions. Finally, none of the classical mechanisms, neither hydrogen-assisted cracking nor slip-step dissolution, can correctly describe the observed behaviour. Some fractographic examinations, and an influence of primary water on the creep rate of Alloy 600, lead to consider that other recent mechanisms, involving an interaction between dissolution and plasticity, have to be considered

Mathematical modelling and TMCP simulation for optimisation of steel behaviour

International Nuclear Information System (INIS)

Siwecki, T.

2001-01-01

Physically based mathematical models for prediction of steel behaviour and microstructure evolution in connection with thermal and thermomechanical controlled processing (TMCP) development in Swedish Institute for Metals Research are discussed. The models can be used for computer predictions of recrystallization and grain growth of austenite after deformation, precipitation or dissolution of microalloying carbonitride in austenite, flow stress during hot working, phase transformation behaviour during accelerated cooling as well as the final microstructure and mechanical properties. The database, which contains information about steel behaviour for a large number of HSLA steels, is also presented. Optimization of TMCP parameters for improving the properties of the steel are discussed in relation to the microstructure and mechanical properties. The effect of TMCP parameters (reheating temperature, rolling schedules and finish rolling temperature as well as accelerated control cooling) on steel properties was studied in laboratory scale. (author)

Modelling and experimental contrast of the mechanical behaviour of structural laminated glass

Directory of Open Access Journals (Sweden)

Sanz-Ablanedo, E.

2010-12-01

Full Text Available This paper presents a numerical simulation of the mechanical behaviour of laminated glass plates (glass- PVB-glass and its experimental verification. The viscoelastic characterization of the intermediate layer of PVB has been done by means of stress relaxation tests at various temperatures. The consideration of PVB as a viscoelastic material permits to analyze the real response of the structural element of laminated glass under time variations of temperature, of application of loading, of stress state, etc. Displacements obtained with the numerical analysis have been verified experimentally with laminated glass plates under lateral load using close range photogrammetry and dial gauges indicators. The analysis of results confirms the time dependent behaviour of the glass-PVB-glass laminate and suggests the validity of the proposed model.

Este trabajo presenta la simulación numérica del comportamiento mecánico de placas de vidrio laminado (vidrio-PVB-vidrio y su comprobación experimental. La caracterización viscoelástica de la lámina intermedia de PVB se ha realizado mediante ensayos de relajación de tensiones a diversas temperaturas. La consideración del PVB como material viscoelástico permite analizar la respuesta real del elemento estructural de vidrio laminado ante variaciones en el tiempo de la temperatura, de la velocidad de aplicación de las cargas, del estado tensional, etc. Los desplazamientos obtenidos numéricamente han sido contrastados experimentalmente en placas de vidrio laminado sometidas a carga lateral mediante fotogrametría de objeto cercano y relojes comparadores. Del análisis de los resultados se confirma el comportamiento variable en el tiempo del conjunto vidrio-PVB-vidrio y se deduce la validez de la modelización propuesta.

Structure, mechanical and thermal behaviour of mixtures of polyester resin and dental ceramic waste

Science.gov (United States)

Peña Rodríguez, G.; Martínez Maldonado, L.; Dulce Moreno, H. J.

2016-02-01

The tensile strength and bending strength, structure and thermal behaviour of mixtures of polyester resin (P-2000) and powders (ASTM sieve 200, dental ceramic wastes (dentals impressions, alginate and gypsum) was reported. The samples consisted of mixtures with percentage weights of 50-50%, 60-40%, 70-30%, 80-20%, 90-10%, where the resin was the majority phase, the Mekc (4% wt) was used as catalyst. The structure was studied using SEM and XRD, the thermal behaviour using DSC, TGA and DMA, while the mechanical strength was tested using standards ASTM D790 and D638. Irregular morphology and presence of small agglomerations was observed, with particle sizes between 29.63 and 38.67μm, the presence of different phases of calcium sulphate was found, and that to the increasing the concentration of the powder, the materials becomes more crystalline, increasing its density. An average service temperature of 69.15±4.60°C was found. Vickers hardness values are reported in ranges from 18.65 to 27.96. Considering the elastic modules was established that the materials become more rigid by having more powder concentration.

Modelling the influence of water content on the mechanical behaviour of Callovo-Oxfordian argillite

International Nuclear Information System (INIS)

Jia, Y.; Zhang, F.; Shao, J.F.

2010-01-01

Document available in extended abstract form only. The clay formation provides the geological background to many industrial and engineering applications. Especially in recent years, these types of material have been largely studied because they can be considered as potential host geological barrier for the underground storage of high level radioactive wastes. In view of this, several underground laboratories have been constructed in different countries. For instance: the Meuse/Haute Marne underground research laboratory (France), excavated in Callovo-Oxfordian argillite; the Mont Terri underground rock laboratory (Switzerland), constructed in Opalinus clay; the HADES Underground Research Laboratory (Belgium), located in Boom clay; the AECL underground research laboratory (Canada), achieved in the Lac du Bonnet granite batholith. The research realised in the underground laboratories allows us to obtain extensive experimental measurements and helps us to get a good understanding of the generalised behaviour of theses clays when subjected to complex solicitations (thermal, hydraulic, mechanical and chemical). In the underground storage, the experimental investigation and numerical prediction show that coupled hydro-mechanical processes will occur in the geological barrier for a very long time due to excavation/ ventilation and subsequence backfilling/sealing. In the excavation and exploitation stage, the unloading of host rock creates an EDZ zone and induces an increase local of permeability by several orders of magnitude around the galleries. Moreover, additional damage may be induced by the desaturation/re-saturation processes during ventilation/backfilling phase. On the other hand, the behaviour of clay formation is affected also by the presence of water and the pore pressure evolution. It is necessary to achieve a good understanding of the coupled hydro-mechanical behaviour to of clay formation for the designer of an underground storage. This paper focus on the

Tritium adsorption/release behaviour of advanced EU breeder pebbles

Energy Technology Data Exchange (ETDEWEB)

Kolb, Matthias H.H., E-mail: matthias.kolb@kit.edu; Rolli, Rolf; Knitter, Regina

2017-06-15

The tritium loading of current grades of advanced ceramic breeder pebbles with three different lithium orthosilicate (LOS)/lithium metatitanate (LMT) compositions (20–30 mol% LMT in LOS) and pebbles of EU reference material, was performed in a consistent way. The temperature dependent release of the introduced tritium was subsequently investigated by temperature programmed desorption (TPD) experiments to gain insight into the desorption characteristics. The obtained TPD data was decomposed into individual release mechanisms according to well-established desorption kinetics. The analysis showed that the pebble composition of the tested samples does not severely change the release behaviour. Yet, an increased content of lithium metatitanate leads to additional desorption peaks at medium temperatures. The majority of tritium is released by high temperature release mechanisms of chemisorbed tritium, while the release of physisorbed tritium is marginal in comparison. The results allow valuable projections for the tritium release behaviour in a fusion blanket.

Minocycline reduces mechanical allodynia and depressive-like behaviour in type-1 diabetes mellitus in the rat.

Science.gov (United States)

Amorim, Diana; Puga, Sónia; Bragança, Rui; Braga, António; Pertovaara, Antti; Almeida, Armando; Pinto-Ribeiro, Filipa

2017-06-01

A common and devastating complication of diabetes mellitus is painful diabetic neuropathy (PDN) that can be accompanied by emotional disorders such as depression. A few studies have suggested that minocycline that inhibits microglia may attenuate pain hypersensitivity in PDN. Moreover, a recent study reported that minocycline has an acute antidepressive-like effect in diabetic animals. Here we studied whether (i) prolonged minocycline treatment suppresses pain behaviour in PDN, (ii) the minocycline effect varies with submodality of pain, and (iii) the suppression of pain behaviour by prolonged minocycline treatment is associated with antidepressive-like effect. The experiments were performed in streptozotocin-induced rat model of type-1 diabetes. Pain behaviour was evoked by innocuous (monofilaments) and noxious (paw pressure) mechanical stimulation, innocuous cold (acetone drops) and noxious heat (radiant heat). Depression-like behaviour was assessed using forced swimming test. Minocycline treatment (daily 80mg/kg per os) of three-week duration started four weeks after induction of diabetes. Diabetes induced mechanical allodynia and hyperalgesia, cold allodynia, heat hypoalgesia, and depression-like behaviour. Minocycline treatment significantly attenuated mechanical allodynia and depression-like behaviour, while it failed to produce significant changes in mechanical hyperalgesia, cold allodynia or heat hypoalgesia. The results indicate that prolonged per oral treatment with minocycline has a sustained mechanical antiallodynic and antidepressive-like effect in PDN. These results support the proposal that minocycline might provide a treatment option for attenuating sensory and comorbid emotional symptoms in chronic PDN. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of phase transformations on the mechanical behaviour of refractory ceramics at high temperature;Effets des transformations de phase sur la tenue mecanique a haute temperature des ceramiques refractaires

Energy Technology Data Exchange (ETDEWEB)

Schmitt, N. [LMT-Cachan, ENS de Cachan, UMR 8535 CNRS, Universite Paris 6, 94 - Cachan (France); IUFM de Creteil, Universite Paris-Est Creteil, 93 - Saint-Denis (France); Poirier, J. [CNRS-CEMHTI, 45 - Orleans (France); Polytech, Universite d' Orleans, 45 - Orleans (France)

2009-07-01

Refractories used at high temperature are subjected to high chemical and mechanical stresses. The mastery of their microstructure as well as the phase changes occurring in service is essential to ensure resistance to wear and failure of refractory linings. Great progress has been made: combining efficient techniques for the investigation of the microstructure with powerful numerical tools (thermochemical and thermo-mechanical computations) provides information (e.g., degradation mechanisms) that cannot be obtained directly. Also multi-physical and multi-scale models developing materials with high-performance for higher temperature and with longer lifetime. In this paper, through several examples we show some interactions between the mechanical behavior and the microstructure transformations of refractory ceramics. The tools developed to characterize their microstructure change in situ (e.g., at high temperature) and to identify their kinetics are described. Some methodologies and tools developed in recent years, today, provide a better understanding of in-service behavior of refractories while identifying the critical material and process parameters likely to increase life-time. (authors)

Developmental phonagnosia: Linking neural mechanisms with the behavioural phenotype.

Science.gov (United States)

Roswandowitz, Claudia; Schelinski, Stefanie; von Kriegstein, Katharina

2017-07-15

Human voice recognition is critical for many aspects of social communication. Recently, a rare disorder, developmental phonagnosia, which describes the inability to recognise a speaker's voice, has been discovered. The underlying neural mechanisms are unknown. Here, we used two functional magnetic resonance imaging experiments to investigate brain function in two behaviourally well characterised phonagnosia cases, both 32 years old: AS has apperceptive and SP associative phonagnosia. We found distinct malfunctioned brain mechanisms in AS and SP matching their behavioural profiles. In apperceptive phonagnosia, right-hemispheric auditory voice-sensitive regions (i.e., Heschl's gyrus, planum temporale, superior temporal gyrus) showed lower responses than in matched controls (n AS =16) for vocal versus non-vocal sounds and for speaker versus speech recognition. In associative phonagnosia, the connectivity between voice-sensitive (i.e. right posterior middle/inferior temporal gyrus) and supramodal (i.e. amygdala) regions was reduced in comparison to matched controls (n SP =16) during speaker versus speech recognition. Additionally, both cases recruited distinct potential compensatory mechanisms. Our results support a central assumption of current two-system models of voice-identity processing: They provide the first evidence that dysfunction of voice-sensitive regions and impaired connectivity between voice-sensitive and supramodal person recognition regions can selectively contribute to deficits in person recognition by voice. Copyright © 2017 Elsevier Inc. All rights reserved.

Influence of the mix parameters and microstructure on the behaviour of concrete at high temperature

International Nuclear Information System (INIS)

Kanema, M.; Noumowe, A.; Gallias, J.-L.; Cabrillac, R.

2005-01-01

Concrete is used in structures likely to be exposed to high temperature. Data on the behaviour of concrete at high temperature are necessary to design buildings and other civil engineering structures in order to resist under accidental conditions (fire) or particular conditions of service (storage of radioactive waste). The present experimental study was carried out on the behaviour of five concretes containing the same nature and quantity of aggregates and presenting different water/cement ratios. Concrete specimens were submitted to heating-cooling cycles whose maximum temperatures were 150, 300, 450 and 600 degree C. Measurements of compressive and tensile strength, modulus of elasticity and permeability were carried out on cylindrical specimens before and after heating-cooling cycles. The results showed the influence of concrete mix parameters on the residual properties and the dehydration of the cement paste matrix, the evolution of the permeability and thermal stability of concrete when it is subjected to high temperature. (authors)

Modelling of the high temperature behaviour of metallic materials

International Nuclear Information System (INIS)

Mohr, R.

1999-01-01

The design of components of metallic high-temperature materials by the finite element method requires the application of phenomenological viscoplastic material models. The route from the choice of a convenient model, the numerical integration of the equations and the parameter identification to the design of components is described. The Chaboche-model is used whose evolution equations are explicitly integrated. The parameters are determined by graphical and numerical methods in order to use the material model for describing the deformation behaviour of a chromium steel and an intermetallic titanium aluminide alloy. (orig.)

Structural and mechanical behaviour of LLDPE/HNT nanocomposite films

Energy Technology Data Exchange (ETDEWEB)

Čermák, M.; Kadlec, P. [Department of Technologies and Measurement, Faculty of Electrical Engineering University of West Bohemia, Univerzitni 8, Pilsen 306 14 (Czech Republic); Šutta, P. [New Technologies - Research Centre University of West Bohemia, Univerzitni 8, Pilsen 306 14 (Czech Republic); Polanský, R. [Regional Innovative Centre for Electrical Engineering University of West Bohemia, Univerzitni 8, Pilsen 306 14 (Czech Republic)

2016-03-09

The paper briefly describes structural and mechanical influences of Halloysite nanotubes (HNT) in different level of fulfilment (0, 1, 3, 7 wt%) in the LLDPE commonly used in the cable industry. The influence of HNT on the polymer has been observed and evaluated through the average crystallite size and the micro- deformation by X-Ray diffractometry and the imaging of SEM. Despite the certain inter-phase tension between the polymer and HNT, the influence on the mechanical and combustion behaviour was observed. Measurement showed a higher content of agglomerates in the sample with 7 wt% HNT fulfilment.

Simulation and analysis of the thermal and deformation behaviour of `as-received` and `hydrided` pressure tubes used in the circumferential temperature distribution experiments (end of life/pressure tube behaviour)

Energy Technology Data Exchange (ETDEWEB)

Muir, W C; Bayoumi, M H [Ontario Hydro, Toronto, ON (Canada)

1996-12-31

It is postulated that in-reactor pressure tubes may be subjected to radiation damage and dissolved deuterium which could change the pressure tube characteristics and lead to different behaviour than that of as-received pressure tubes under large LOCA (loss of coolant) conditions. A hydrided pressure tube was used to study the effect of dissolved hydrogen on thermal-mechanical behaviour. In the experiment, simulating an in-reactor (hydrided) pressure tube with circumferential differential temperature under boil-off conditions, the pressure tube ballooned into contact with the calandria tube. The pressure tube used in this experiment was hydrided in a furnace to a nominal value of 200 {mu}g/g dissolved hydrogen. This test was a repeat of the first supplementary boil-off test (S-5-1) which used an as-received pressure tube. The objective of this paper is to analyze the results obtained from the simulation of this Boil-Off test using the SMARTT computer code and to examine the effect of hydriding on the thermal and ballooning behaviour of the pressure tube by comparison with the results obtained from test S-5-1. A discussion of the results obtained from this comparison is presented together with an analysis of their application to the analysis of pressure tube behaviour in CANDU reactors. (author). 13 refs., 1 tab., 16 figs.

Simulation and analysis of the thermal and deformation behaviour of 'as-received' and 'hydrided' pressure tubes used in the circumferential temperature distribution experiments (end of life/pressure tube behaviour)

International Nuclear Information System (INIS)

Muir, W.C.; Bayoumi, M.H.

1995-01-01

It is postulated that in-reactor pressure tubes may be subjected to radiation damage and dissolved deuterium which could change the pressure tube characteristics and lead to different behaviour than that of as-received pressure tubes under large LOCA (loss of coolant) conditions. A hydrided pressure tube was used to study the effect of dissolved hydrogen on thermal-mechanical behaviour. In the experiment, simulating an in-reactor (hydrided) pressure tube with circumferential differential temperature under boil-off conditions, the pressure tube ballooned into contact with the calandria tube. The pressure tube used in this experiment was hydrided in a furnace to a nominal value of 200 μg/g dissolved hydrogen. This test was a repeat of the first supplementary boil-off test (S-5-1) which used an as-received pressure tube. The objective of this paper is to analyze the results obtained from the simulation of this Boil-Off test using the SMARTT computer code and to examine the effect of hydriding on the thermal and ballooning behaviour of the pressure tube by comparison with the results obtained from test S-5-1. A discussion of the results obtained from this comparison is presented together with an analysis of their application to the analysis of pressure tube behaviour in CANDU reactors. (author). 13 refs., 1 tab., 16 figs

Aging temperature and abrasive wear behaviour of cast Al-(4%, 12%, 20%)Si-0.3% Mg alloys

International Nuclear Information System (INIS)

Shah, K.B.; Kumar, Sandeep; Dwivedi, D.K.

2007-01-01

In the present paper, influence of aging temperature during artificial age hardening treatment (T 6 ) of cast Al-(4, 12, 20%)Si-0.3% Mg on abrasive wear behaviour has been reported. Alloys were prepared by controlled melting and casting. Cast alloys were given age hardening treatment having sequence of solutionizing, quenching and artificial aging. All the alloys were solutionized at 510 deg. C for 8 h followed by water quenching (30 deg. C) and aging hardening at 150, 170, 190, 210 and 230 deg. C for 12 h. Abrasive wear tests were conducted against of 320 grade SiC abrasive medium at 5 and 10 N normal loads. It was observed that the silicon content and aging temperature significantly affect the wear resistance. Increase in aging temperature improves the wear resistance. Hypereutectic alloy showed better wear resistance than the eutectic alloy under identical conditions. Optical microstructure study of alloys under investigation has shown that cast dendritic structure is destroyed besides the spheroidization of eutectic silicon crystals after the heat treatment. The extent of change in structure depends on aging temperature. Scanning electron microscopy (SEM) of wear surface was carried to analyze the wear mechanism

Concepts on Low Temperature Mechanical Grain Growth

Energy Technology Data Exchange (ETDEWEB)

Sharon, John Anthony [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Metallurgy and Materials Joining Dept.; Boyce, Brad Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Metallurgy and Materials Joining Dept.

2013-11-01

In metals, as grain size is reduced below 100nm, conventional dislocation plasticity is suppressed resulting in improvements in strength, hardness, and wears resistance. Existing and emerging components use fine grained metals for these beneficial attributes. However, these benefits can be lost in service if the grains undergo growth during the component’s lifespan. While grain growth is traditionally viewed as a purely thermal process that requires elevated temperature exposure, recent evidence shows that some metals, especially those with nanocrystalline grain structure, can undergo grain growth even at room temperature or below due to mechanical loading. This report has been assembled to survey the key concepts regarding how mechanical loads can drive grain coarsening at room temperature and below. Topics outlined include the atomic level mechanisms that facilitate grain growth, grain boundary mobility, and the impact of boundary structure, loading scheme, and temperature.

Influence of heat treatment on the high temperature oxidation mechanisms of an Fe-TiCN cermet

OpenAIRE

Alvaredo Olmos, Paula; Abajo Clemente, Carolina; Tsipas, Sophia Alexandra; Gordo Odériz, Elena

2014-01-01

In this study, the oxidation behaviour of an iron matrix cermet containing 50 % vol. Ti(C,N) was investigated before and after heat treatment by oxidation tests performed in static air at temperatures between 500 °C and 1000 °C. The oxidation mechanism for this type of composite materials was established and it was found that the heat treated material presents lower mass gain than the as-sintered material at the early stages of the oxidation, due to the volatilization of oxides. The oxidation...

The effect of strain rate and temperature on the tensile behaviour of uranium 2 w/o molybdenum

International Nuclear Information System (INIS)

Harding, J.; Boyd, G.A.C.

1983-01-01

This report describes the uniaxial tensile behaviour of uranium 2 w/o molybdenum alloy over a wide range of temperature and strain rate. Specimen blanks taken from co-reduced and extruded U 2 w/o Mo rods were given one of two heat treatments. Longitudinal tensile test pieces, taken from these blanks at near surface locations were tested in the temperature range -150 deg C to +100 deg C at strain rates from quasistatic (10 -4 s -1 ) to 10 3 s -1 . To achieve this range of testing rates three machines were required: an Instron screw driven machine for rates up to 0.1 s -1 , a second specially constructed hydraulic machine for the range 0.1 s -1 to 50 s -1 and a drop weight machine for the highest strain rates. The ways in which the mechanical properties - elongation to fracture, flow stresses and ultimate tensile stress - vary with both temperature and strain rate are presented and discussed for material in both heat treatment conditions. (author)

Mechanical behaviour of dissimilar metal welds

International Nuclear Information System (INIS)

Escaravage, C.

1990-01-01

This report addresses the problems of dissimilar metal welds connecting an austenitic stainless steel component to a ferritic steel component. In LMFBRs such welds appear at the junction of the austenitic stainless steel vessel with the ferritic steel roof and in sodium and water or steam pipes. The latter are exposed to high temperatures in the creep range. A wide range of austenitic stainless steels and ferritic steels (carbon steels, low allow steels and alloy steels) are covered; the study encompasses more than 20 different weld metals (austenitic stainless steels and nickel base alloys). The report begins with a presentation of the materials, geometries and welding procedures treated in the study, followed by a review of service experience from examinations of dissimilar metal welds after elevated temperature service, in particular failed welds. Results of laboratory tests performed for reproducing service failures are then discussed. A further section is devoted to a review of test results on fatigue behaviour and impact toughness for dissimilar metal welded joints when creep is not significant. Finally, the problem of residual life assessment is addressed. A set of recommendations concludes the report. They concern the material selection, welding procedure, life prediction and testing of dissimilar metal welds. 84 refs

Analysing hydro-mechanical behaviour of reinforced slopes through centrifuge modelling

Science.gov (United States)

Veenhof, Rick; Wu, Wei

2017-04-01

Every year, slope instability is causing casualties and damage to properties and the environment. The behaviour of slopes during and after these kind of events is complex and depends on meteorological conditions, slope geometry, hydro-mechanical soil properties, boundary conditions and the initial state of the soils. This study describes the effects of adding reinforcement, consisting of randomly distributed polyolefin monofilament fibres or Ryegrass (Lolium), on the behaviour of medium-fine sand in loose and medium dense conditions. Direct shear tests were performed on sand specimens with different void ratios, water content and fibre or root density, respectively. To simulate the stress state of real scale field situations, centrifuge model tests were conducted on sand specimens with different slope angles, thickness of the reinforced layer, fibre density, void ratio and water content. An increase in peak shear strength is observed in all reinforced cases. Centrifuge tests show that for slopes that are reinforced the period until failure is extended. The location of shear band formation and patch displacement behaviour indicate that the design of slope reinforcement has a significant effect on the failure behaviour. Future research will focus on the effect of plant water uptake on soil cohesion.

Effect of corrosion potential on the corrosion fatigue crack growth behaviour of low-alloy steels in high-temperature water

International Nuclear Information System (INIS)

Ritter, S.; Seifert, H.P.

2008-01-01

The low-frequency corrosion fatigue (CF) crack growth behaviour of different low-alloy reactor pressure vessel steels was characterized under simulated boiling water reactor conditions by cyclic fatigue tests with pre-cracked fracture mechanics specimens. The experiments were performed in the temperature range of 240-288 deg. C with different loading parameters at different electrochemical corrosion potentials (ECPs). Modern high-temperature water loops, on-line crack growth monitoring (DCPD) and fractographical analysis by SEM were used to quantify the cracking response. In this paper the effect of ECP on the CF crack growth behaviour is discussed and compared with the crack growth model of General Electric (GE). The ECP mainly affected the transition from fast ('high-sulphur') to slow ('low-sulphur') CF crack growth, which appeared as critical frequencies ν crit = f(ΔK, R, ECP) and ΔK-thresholds ΔK EAC f(ν, R, ECP) in the cycle-based form and as a critical air fatigue crack growth rate da/dt Air,crit in the time-domain form. The critical crack growth rates, frequencies, and ΔK EAC -thresholds were shifted to lower values with increasing ECP. The CF crack growth rates of all materials were conservatively covered by the 'high-sulphur' CF line of the GE-model for all investigated temperatures and frequencies. Under most system conditions, the model seems to reasonably well predict the experimentally observed parameter trends. Only under highly oxidizing conditions (ECP ≥ 0 mV SHE ) and slow strain rates/low loading frequencies the GE-model does not conservatively cover the experimentally gathered crack growth rate data. Based on the GE-model and the observed cracking behaviour a simple time-domain superposition-model could be used to develop improved reference CF crack growth curves for codes

Influence of the chemical composition and the fabrication process on the behaviour of high temperature oxidation of Fe-Cr-Al alloys

International Nuclear Information System (INIS)

Clemendot, F.; Arnoldi, F.; Cerede, J.B.; Dionnet, B.; Nardou, F.; Duysen, J.C. van

1993-01-01

The oxidation behaviour of four industrial Fe-Cr-Al alloys was studied. Two of them were Fe-Cr-Al alloys fabricated either by melting or by powder metallurgy. The two other ones were Fe-Cr-Al-Y alloys either produced by melting or by mechanical alloying. On these alloys, we determined oxidation kinetics and observed the morphology of the oxide layer after isothermal and cyclic exposures from 1000 C up to 1300 C. The beneficial effect of yttrium on the adherence of oxide layers was confirmed. The powder metallurgy fabrication route does not improve the oxidation resistance of yttrium-free alloys. On the other hand, the association of the powder metallurgy and the addition of yttrium allow the manufacturing of alloys which present an excellent behaviour to high temperature oxidation. (orig.)

Early age mechanical behaviour of 3D printed concrete : Numerical modelling and experimental testing

NARCIS (Netherlands)

Wolfs, R.J.M.; Bos, F.P.; Salet, T.A.M.

2018-01-01

A numerical model was developed to analyse the mechanical behaviour of fresh, 3D printed concrete, in the range of 0 to 90 min after material deposition. The model was based on a time-dependent Mohr-Coulomb failure criterion and linear stress-strain behaviour up to failure. An experimental program,

Modeling of the thermo-mechanical behaviour of the PWR fuel

International Nuclear Information System (INIS)

Mailhe, P.

2014-01-01

This article reviews the various physical phenomena that take place in an irradiated fuel rod and presents the development of the thermo-mechanical codes able to simulate them. Though technically simple the fuel rod is the place where appear 4 types of process: thermal, gas behaviour, mechanical and corrosion that combine involving 5 elements: the fuel pellet, the fuel clad, the fuel-clad gap, the inside volume and the coolant. For instance the pellet is the place where the following mechanical processes took place: thermal dilatation, elastic deformation, creep deformation, densification, solid swelling, gaseous swelling and cracking. The first industrial code simulating the behaviour of the fuel rod was COCCINEL, it was developed by AREVA teams from the American PAD code that was included in the Westinghouse license. Today the GALILEO code has replaced the COPERNIC code that was developed in the beginning of the 2000 years. GALILEO is a synthesis of the state of the art of the different models used in the codes validated for PWR and BWR. GALILEO has been validated on more than 1500 fuel rods concerning PWR, BWR and specific reactors like Siloe, Osiris, HFR, Halden, Studsvik, BR2/3,...) and also for extended burn-ups. (A.C.)

Mechanical behaviour of structural ceramics

Directory of Open Access Journals (Sweden)

Bueno, S.

2007-06-01

Full Text Available The use of ceramic materials in structural applications is limited by the lack of reliability associated with brittle fracture behaviour. In order to extend the structural use of ceramics, the design of microstructures which exhibit flaw tolerance due to toughening mechanisms which produce an increase in crack growth resistance during crack propagation has been proposed. This work is a review of the mechanical behaviour of structural ceramic materials and its characterisation. Firstly, the basic brittle fracture parameters and the statistical criteria to determine the probability of exceeding the safety factors demanded for a particular application are analysed. Then, the toughening mechanisms which can be developed in the materials through microstructural design as well as the mechanical characterisation of toughened ceramics are discussed. The experimental values of linear elastic fracture toughness parameters (critical stress intensity factor, KIC, and critical energy release rate, GIC are not intrinsic properties for toughened materials and depend on crack length and the loading system. In this work, the different mechanical parameters proposed to characterise such materials are reviewed. The following fracture parameters are analysed: work of fracture (γWOF, critical J-integral value (JIC and R-curve. For the determination, stable fracture tests are proposed in order to ensure that the energy provided during the test is no more than the necessary one for crack propagation.

El uso de los materiales cerámicos en aplicaciones estructurales está limitado por la falta de fiabilidad asociada a su comportamiento frágil durante la fractura. Para extender su aplicación se ha propuesto el diseño de microestructuras que presenten tolerancia a los defectos debido a la actuación de mecanismos de refuerzo. Este trabajo es una puesta al día sobre el estudio del comportamiento mecánico de los materiales cerámicos estructurales y su

Temperature sensitive self-actuated scram mechanism

International Nuclear Information System (INIS)

1980-01-01

The apparatus, described in detail, accurately infers the average coolant temperature exiting from the reactor core in a liquid metal cooled reactor and rapidly and reliably actuates a safety rod release mechanism on the occurrence of a critical temperature. The output temperature is inferred from the cooperative effect of the flow rate through a coolant flow path within the safety assembly and the heat generated by sensor fuel pins. The inferred temperature is sensed by a confined fluid having a high expansion coefficient; the expansion is transferred to a linear force used to actuate the release mechanism. The system may be contained within the safety assembly and does not interfere with the operation of the plant protection system scram mode. It is resetable after a scram. The time interval between the overtemperature and the insertion of the safety rods is short enough to preclude fuel damage. (U.K.)

Economic recession and suicidal behaviour: Possible mechanisms and ameliorating factors.

Science.gov (United States)

Haw, Camilla; Hawton, Keith; Gunnell, David; Platt, Stephen

2015-02-01

A growing body of research evidence from countries around the world indicates that economic recession is associated with increases in suicide, particularly in males of working age. To explore contributory and ameliorating factors associated with economic recession and suicide and thereby stimulate further research in this area and encourage policy makers to consider how best to reduce the impact of recession on mental health and suicidal behaviour. We conducted a selective review of the worldwide literature focusing on possible risk factors, mechanisms and preventative strategies for suicidal behaviour linked to economic recession. A model of how recession might affect suicide rates is presented. A major and often prolonged effect of recession is on unemployment and job insecurity. Other important effects include those exerted by financial loss, bankruptcy and home repossession. It is proposed these factors may lead directly or indirectly to mental health problems such as depression, anxiety and binge drinking and then to suicidal behaviour. Countries with active labour market programmes and sustained welfare spending during recessions have less marked increases in suicide rates than those that cut spending on welfare and job-search initiatives for the unemployed. Other measures likely to help include targeted interventions for unemployed people, membership of social organisations and responsible media reporting. Good primary care and mental health services are needed to cope with increased demand in times of economic recession but some governments have in fact reduced healthcare spending as an austerity measure. The research evidence linking recession, unemployment and suicide is substantial, but the evidence for the other mechanisms we have investigated is much more tentative. We describe the limitations of the existing body of research as well as make suggestions for future research into the effects of economic recession on suicidal behaviour. © The Author

Dynamic tensile behaviour and deformational mechanism of C5191 phosphor bronze under high strain rates deformation

Energy Technology Data Exchange (ETDEWEB)

Hu, Dao-chun [College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); College of Mechanical and Electrical Engineering, Taizhou Vocational & Technical College, Taizhou 318000 (China); Chen, Ming-he, E-mail: meemhchen@nuaa.edu.cn [College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); Wang, Lei; Cheng, Hu [College of Mechanical Engineering, Taizhou University, Taizhou 318000 (China)

2016-01-01

High speed stamping process is used to high strength and high electrical conductivity phosphor bronze with extremely high strain rates more than 10{sup 3} s{sup −1}. This study on the dynamic tensile behaviour and deformational mechanism is to optimise the high speed stamping processes and improve geometrical precision in finished products. Thus, the tensile properties and deformation behaviour of C5191 phosphor bronze under quasi-static tensile condition at a strain rate of 0.001 s{sup −1} by electronic universal testing machine, and dynamic tensile condition at strain rate of 500, 1000 and 1500 s{sup −1} by split Hopkinson tensile bar (SHTB) apparatus were studied. The effects of strain rate and the deformation mechanism were investigated by means of SEM and TEM. The results showed that the yield strength and tensile strength of C5191 phosphor bronze under high strain rates deformation increased by 32.77% and 11.07% respectively compared with quasi-static condition, the strain hardening index increases from 0.075 to 0.251, and the strength of the material strain rates sensitivity index change from 0.005 to 0.022, which presented a clear sensitive to strain rates. Therefore, it is claimed that the dominant deformation mechanism was changed by the dislocation motion under different strain rates, and the ability of plastic deformation of C5191 phosphor bronze increased due to the number of movable dislocations increased significantly, started multi-line slip, and the soft effect of adiabatic temperature rise at the strain rate ranging from 500 to 1500 s{sup −1}.

Model investigation of fuel rod behaviour

International Nuclear Information System (INIS)

Girgis, M.M.; Wiesenack, W.; Stegemann, D.

1985-06-01

Thermal and mechanical behaviour of fuel rods can be explained but unsatisfactorily by models based of an axial symmetry concept. Recently developed models include, with respect to their thermal components, a simple method for the computation of the temperature distribution within the fuel, and they also take into account the influence of excentrically placed pellets for the computation of heat transfer in the cold gap. Additionally, a finite-element model is used to evaluate the effects of cracking and fragmentation on the thermal behaviour of pellets. The reaction of fuel and fuel cladding to external and internal loadings and the axial interaction between fuel and cladding are described in the mechanical portion of the model. A special case of axial coupling is the so-called random stacking interaction caused by fuel pellets placed excentrically at the cladding and sliding radially and axially. In the comparison of measurement results, both thermal and mechanical behaviour of different rods from the OECD Halden Reactor Project are subject to investigations. (RF) [de

Hot deformation of polycrystalline uranium dioxide: from microscopic mechanisms to macroscopic behaviour

International Nuclear Information System (INIS)

Dherbey, Francine

2000-01-01

The improvement of nuclear fuels performances in PWR requires in particular an enhancement of creep ability of uranium dioxide in order to minimise rupture risks of the cladding material during interactions between pellets and cladding. The aim of this study is to investigate the link between the ceramic macroscopic thermo-mechanical behaviour and the changes in the fuel microstructure during deformation. Stoichiometric UO 2 pellets with various grains sizes from 9 pm to 36 μm have been deformed by compression at intermediate temperatures, i.e. near T M /2, and quenched under stress. The damage is characterised by the presence of cavities at low stresses and cracks at high stresses, both along grain boundaries parallel to the compression axis. Inside grains, dislocations organise themselves into cellular substructures in which sub-boundaries are made of dislocation hexagonal networks. In these conditions, uranium dioxide deformation is described by grain boundary sliding, which is the main origin of material damage, partially accommodated by dislocational creep inside grains. A steady-state creep model is proposed on a physical basis. It accounts for the almost similar contributions of two mechanisms which are grain boundaries sliding and intragranular creep, and takes into account the grain boundary roughness. In contrast with phenomenological descriptions used up to now, this picture leads to a unique creep law on the whole range of stresses explored here, from 10 MPa to 80 MPa. The creep rate controlling mechanism seems to be the migration of sub-boundaries. The deformation at constant strain rate is controlled by the same mechanisms as creep. (author) [fr

Temperature sensitive self-actuated scram mechanism

International Nuclear Information System (INIS)

Giuggio, N.; Noyes, R.C.; Zaman, S.U.

1980-01-01

A self-actuated mechanism within a safety assembly in a liquid metal nuclear reactor comprising sensor fuel pins located in a reactor coolant flow path, a sensor bulb containing NaK located near the upper end of the sensor fuel pins and in the reactor coolant flow path, and a sensor tube connecting the sensor bulb to a metal bellows and push rod. The motion of the push rod resulting from the temperature dependent change in the NaK volume actuates a safety rod release mechanism when a predetermined coolant temperature is reached

Mechanical pumping at low temperature

Energy Technology Data Exchange (ETDEWEB)

Perin, J.P.; Claudet, G.; Disdier, F.

1994-12-31

This new concept consists of a mechanical pump able to run at low temperature (25 K). Since gas density varies inversely with temperature, the pump could deliver much higher mass flow rate than at room temperature for a given size. Advantages of this concept are reduction of an order of magnitude in size and weight when compared to a conventional pump scaled to perform the same mass flow rate at room temperature. Results obtained at 80 K and 25 K with a Holweck type molecular drag pump of 100 mm diameter and with few stages of a turbomolecular pump running at the same temperatures, are given. This pump would be a solution to allow continuous tritium extraction and minimize the mass inventory for the ITER (International Tokamak Experiment Reactor). 5 figs., 2 tabs., 4 refs.

Influence of the temperature on materials electric behaviour: Understanding and students’ learning difficulties

Directory of Open Access Journals (Sweden)

Antonio García Carmona

2006-03-01

Full Text Available In this article, we defend that in the teaching/learning of the electricity, its contents must be associa ted with contents concerning the structure and behaviour of the matter. Thus, it is possible to understand some electricity topics as the influence of the temperature on electric behaviour of materials. In this sense, we propose a conceptual framework for its teaching, coherent with the Spanish Physics and Chemistry curriculum of Secondary Education. Likewise, we show the results of a research carried out with 60 pupils (age 14-15, about theirs understanding levels and theirs learning difficulties regarding considered topic.

High temperature behaviour of E110G and E110 fuel claddings in various mixtures of steam and air

International Nuclear Information System (INIS)

Perez-Feró, Erzsébet; Novotny, Tamás; Horváth, Márta; Kunstár, Mihály; Vér, Nóra; Hózer, Zoltán

2014-01-01

Experiments with sponge base E110G and the traditional E110 were carried out to compare the oxidation kinetics of these alloys in steam, in hydrogen rich steam, in steam-air and in air atmosphere and to study the effect of hydrogen- and nitrogen-containing environment on the oxidation. The effect of oxidizing atmosphere on the mechanical behaviour of the claddings was also investigated. The new and the traditional types of cladding rings were oxidised at high temperature (600°C – 1200°C). Oxidation of both alloys in steam-air mixture and in air atmosphere resulted in faster oxidation kinetics compared to steam. In many cases bumpy, porous oxide layer have been found. The presence of hydrogen in the steam atmosphere had no significant effect on the oxidation kinetics. Comparing the two alloys, more favourable behaviour of oxidised E110G was observed regarding the oxidation kinetics, breakaway oxidation and load bearing capability in all cases. (author)

Material Properties at Low Temperature

International Nuclear Information System (INIS)

Duthil, P

2014-01-01

From ambient down to cryogenic temperatures, the behaviour of materials changes greatly. Mechanisms leading to variations in electrical, thermal, mechanical, and magnetic properties in pure metals, alloys, and insulators are briefly introduced from a general engineering standpoint. Data sets are provided for materials commonly used in cryogenic systems for design purposes

Material Properties at Low Temperature

CERN Document Server

Duthil, P

2014-07-17

From ambient down to cryogenic temperatures, the behaviour of materials changes greatly. Mechanisms leading to variations in electrical, thermal, mechanical, and magnetic properties in pure metals, alloys, and insulators are briefly introduced from a general engineering standpoint. Data sets are provided for materials commonly used in cryogenic systems for design purposes.

Material Properties at Low Temperature

Energy Technology Data Exchange (ETDEWEB)

Duthil, P [Orsay, IPN (France)

2014-07-01

From ambient down to cryogenic temperatures, the behaviour of materials changes greatly. Mechanisms leading to variations in electrical, thermal, mechanical, and magnetic properties in pure metals, alloys, and insulators are briefly introduced from a general engineering standpoint. Data sets are provided for materials commonly used in cryogenic systems for design purposes.

The electrochemical behaviour of copper in aerated 1 mol·dm-3 NaCl at room temperature: Pt. 2

International Nuclear Information System (INIS)

King, F.; Litke, C.D.

1989-05-01

Uniform corrosion will be an important process in determining the lifetime of a copper nuclear fuel waste container. We need to know the mechanism of the corrosion reaction if we are to make reliable predictions about the long-term corrosion behaviour. This series of reports summarizes the results of an electrochemical investigation of the corrosion of copper in aerated 1 mol·dm -3 NaCl at room temperature. In part 2 we discuss the cathodic reduction of oxygen on a copper rotating disc electrode. The anodic dissolution of copper and the behaviour under freely corroding conditions are considered in Parts 1 and 3, respectively. The mechanism of the oxygen reduction reaction has been studied over a wide range of applied potentials. At potentials close to the corrosion potential, the mechanism is complicated and not fully understood. It is possible that in this potential region, oxygen is reduced to peroxide. At more negative applied potentials, between -0.50 and -0.90 V sce , the predominant process is the 4-electron reduction of oxygen to hydroxide. In this potential region, the rate is controlled jointly by the interfacial reaction and the rate of supply of oxygen to the electrode surface. At an applied potential of about -1.0 V sce , the rate of reduction is almost totally controlled by the rate of transport of oxygen. Values for the kinetic parameters for the 4-electron reaction have been determined. In addition, the diffusion coefficient of oxygen was found to be 1.7 3 ± 0.0 5 x 10 -5 cm 2 ·s -1 . These data, along with the results on the anodic dissolution of copper, will be used to explain the behaviour of copper under freely corroding conditions

Mechanical properties and flexure behaviour of lightweight foamed concrete incorporating coir fibre

Science.gov (United States)

Mohamad, Noridah; Afif Iman, Muhamad; Othuman Mydin, M. A.; Samad, A. A. A.; Rosli, J. A.; Noorwirdawati, A.

2018-04-01

This paper presents an experimental investigation on the mechanical properties and flexural behaviour of lightweight foamed concrete (LFC) with added coir fibre as filler. The compressive strength (Pt), tensile strength (Ft), modulus of elasticity (E), ultimate load and crack pattern of the foamed concrete were determined. The coir fibre was added to the foamed concrete mixture at 0.1%, 0.2% and 0.3% of the total weight of cement. Effects of various percentage of coir fibre used on foam concrete’s mechanical and properties and flexural behaviour were studied and analysed. It was found that the increase percentage of fibre resulted in increase in compressive strength, tensile strength and modulus of elasticity of LFC mixture. LFC with added coir of 0.3% experienced the smallest crack propagation.

Direct effects of incubation temperature on morphology, thermoregulatory behaviour and locomotor performance in jacky dragons (Amphibolurus muricatus).

Science.gov (United States)

Esquerré, Damien; Keogh, J Scott; Schwanz, Lisa E

2014-07-01

Incubation temperature is one of the most studied factors driving phenotypic plasticity in oviparous reptiles. We examined how incubation temperature influenced hatchling morphology, thermal preference and temperature-dependent running speed in the small Australian agamid lizard Amphibolurus muricatus. Hatchlings incubated at 32 °C grew more slowly than those incubated at 25 and 28 °C during their first month after hatching, and tended to be smaller at one month. These differences were no longer significant by three months of age due to selective mortality of the smallest hatchlings. The cooler incubation treatments (25 °C and 28 °C) produced lizards that had deeper and wider heads. Hatchlings from 28 °C had cooler and more stable temperature preferences, and also had lower body temperatures during a 2-h thermoregulatory behaviour trial. Locomotor performance was enhanced at higher body temperatures, but incubation temperature had no measurable effect either independently or in interaction with body temperature. Our study demonstrates that incubation temperature has direct effects on morphology and thermoregulatory behaviour that appears to be independent of any size-dependent effects. We postulate a mechanistic link between these two effects. Copyright © 2014 Elsevier Ltd. All rights reserved.

A review of mechanical and tribological behaviour of polymer composite materials

Science.gov (United States)

Prabhakar, K.; Debnath, S.; Ganesan, R.; Palanikumar, K.

2018-04-01

Composite materials are finding increased applications in many industrial applications. A nano-composite is a matrix to which nanosized particles have been incorporated to drastically improve the mechanical performance of the original material. The structural components produced using nano-composites will exhibit a high strength-to-weight ratio. The properties of nano-composites have caused researchers and industries to consider using this material in several fields. Polymer nanocomposites consists of a polymer material having nano-particles or nano-fillers dispersed in the polymer matrix which may be of different shapes with at least one of the dimensions less than 100nm. In this paper, comprehensive review of polymer nanocomposites was done majorly in three different areas. First, mechanical behaviour of polymer nanocomposites which focuses on the mechanical property evaluation such as tensile strength, impact strength and modulus of elasticity based on the different combination of filler materials and nanoparticle inclusion. Second, wear behavior of Polymer composite materials with respect to different impingement angles and variation of filler composition using different processing techniques. Third, tribological (Friction and Wear) behaviour of nanocomposites using various combination of nanoparticle inclusion and time. Finally, it summarized the challenges and prospects of polymer nanocomposites.

Influence of temperature on oxidation behaviour of ZE41 magnesium alloy

International Nuclear Information System (INIS)

Lopez, M.D.; Munez, C.J.; Carboneras, M.; Rodrigo, P.; Escalera, M.D.; Otero, E.

2010-01-01

The influence of temperature on the oxidation behaviour of commercial ZE41 magnesium alloy has been studied. Thermogravimetric tests were carried out to determine the oxidation kinetics in the 350-500 o C range. Morphology and growth of the oxidation films were analysed by Scanning Electronic Microscopy (SEM), Energy Dispersive X-Ray Spectrometry (EDS) and X-Ray Diffraction (XRD). It was found that the oxidation kinetics initially follow a parabolic law, following a linear law for higher exposure times. Results also showed that the protective nature of the oxide layer depends on the oxidation temperature. At temperatures in the range of 350-450 o C the ZE41 alloy is covered by a protective oxide layer, very thin and compact, whereas the oxide layer formed at 500 o C exhibits a non-protective nature, showing an 'oxide sponges' morphology.

The effect of strain rate and temperature on the tensile behaviour of uranium - 2sup(w)/o molybdenum

International Nuclear Information System (INIS)

Harding, J.; Boyd, G.A.C.

1983-01-01

This report describes the uniaxial tensile behaviour of uranium 2 w/o molybdenum alloy over a wide range of temperature and strain rate. Specimen blanks taken from co-reduced and extruded U2 w/o Mo rods were given one of two heat treatments. Longitudinal tensile test pieces, taken from these blanks at near surface locations were tested in the temperature range -150 deg C to +100 deg C at strain rates from quasistatic (10 -4 s -1 ) to 10 3 s -1 . To achieve this range of testing rates three machines were required: an Instron screw driven machine for rates up to 0.1 s -1 , a second specially constructed hydraulic machine for the range 0.1 s -1 to 50 s -1 and a drop weight machine for the highest strain rates. The ways in which the mechanical properties - elongation to fracture, flow stresses and ultimate tensile stress - vary with both temperature and strain rate are presented and discussed for material in both heat treatment conditions. (author)

The Effect of Increased Temperature on Flowering Behaviour of Saffron (Crocus sativus L.

Directory of Open Access Journals (Sweden)

A. Koocheki

2011-01-01

Full Text Available Abstract Flowering in saffron requires a period of incubation at high temperatures for flower differentiation followed by a period of low temperatures for flower emergence. Global warming could adversely affect the flowering of saffron because of its high sensitivity to temperature. Flowering behaviour of saffron in response to rising temperature was studied in an experiment conducted in controlled environment. Corms with identical sizes were collected form green or fully withered field grown plants and sown in plastic pots. Pots were incubated in 25, 27 and 30 °C for 70, 90 and 120 days. By the end of each incubation period, pots incubated in 25, 27 and 30 °C were transferred to 17, 19 and 21 °C, respectively. Days to flowering, development rate and growth characteristics of saffron were measured in alternative temperature regimes of 25/17, 27/19 and 30/21 °C in combination with 3 incubation periods and in 3 replications. The results indicated that increasing incubation temperature up to 27 °C had no significant effects on saffron flowering behaviour however, no flower was appeared from corms incubated in 30°C. Increased duration of incubation period had adverse effects on flower emergence and corms incubated for 120 days were only flowered in 27/19 °C temperature regime. The optimal flowering response and the highest number of vegetative buds was obtained when 90 days incubation period at 27 °C was followed by a period for flower emergence at 17°C. Corms lifted from green or withered plants showed similar response to temperature regimes and incubation periods. However, in average duration of sowing to flowering was 5 days longer in corms lifted from green plants. Comparing the results of this research with daily temperature in the main saffron production areas of Khorasan provinces showed that increasing mean daily temperature by 2 °C during summer and autumn results in a considerable delay in flowering of saffron.

Does behavioural thermoregulation underlie seasonal movements in Lake Erie walleye?

Science.gov (United States)

Raby, Graham D.; Vandergoot, Christopher; Hayden, Todd A.; Faust, Matthew D.; Kraus, Richard T.; Dettmers, John M.; Cooke, Steven J.; Zhao, Yingming; Fisk, Aaron T.; Krueger, Charles C.

2018-01-01

Thermoregulation is presumed to be a widespread determinant of behaviour in fishes, but has not often been investigated as a mechanism shaping long-distance migrations. We used acoustic telemetry and animal-borne thermal loggers to test the hypothesis that seasonal migration in adult walleye (Sander vitreus) in Lake Erie is size- and (or) sex-specific and related to behavioural thermoregulation. Female walleye migrated out of the warm, shallow western basin earlier than did males and were 1.8 times more likely to be detected on acoustic receivers in the deeper and cooler eastern basin. The few fish that remained in the western basin were restricted to a smaller range of higher temperatures (≥20 °C) than those that migrated to the central and eastern basins (∼16–21 °C). However, temperature records from walleye in the central basin were nearly indistinguishable from those in the eastern basin, suggesting thermal preferences alone could not explain migration to the eastern basin. As such, our effort to understand the mechanisms that cause migratory behaviours has generated mixed evidence on the role of temperature and that factors like foraging opportunities may have synergistic roles in the migration.

Thermo-mechanical fatigue behaviour of the near-{gamma}-titanium aluminide alloy TNB-V5 under uniaxial and multiaxial loading

Energy Technology Data Exchange (ETDEWEB)

Brookes, Stephen Peter

2009-12-19

With increasing environmental awareness and the general need to economise on the use of fossil fuels, there is growing pressure for industry to produce lighter, more efficient, gas turbine engines. One such material that will help to achieve these improvements is the intermetallic gamma titanium aluminide ({gamma}-TiAl) alloy. At only half the density of current nickel-based superalloys its weight saving capability is highly desirable, however, its mechanical properties have not yet been fully explored especially, when it is to be considered for structural components in aeronautical gas turbine engines. Critical components in these engines typically experience large variations in temperatures and multiaxial states of stress under non-isothermal conditions. These stress states are known as tri-axial thermo-mechanical fatigue (TMF). The work presented here investigates the effects these multi-axial stresses, have on a {gamma}-TiAl, (Ti-45Al-5Nb-0.2B-0.2C) alloy under TMF conditions. The uniaxial, torsional and axialtorsional TMF behaviour of this {gamma}-TiAl alloy have been examined at 400 - 800 C with strain amplitudes ranging from 0.15% to 0.7%. The tests were conducted at both thermomechanical in-phase (IP) and out-of-phase (OP). Selected tests additionally contained a 180 seconds hold period. Fatigue lifetimes are strongly influenced by the strain amplitude, a small increase in amplitude reduces the lifetime considerably. The uniaxial IP tests showed significantly longer fatigue lifetimes than of all the tests performed. Torsional loading although have shorter fatigue lifetimes than the uniaxial IP loading they have longer fatigue lifetimes than the uniaxial OP loading. The non-proportional axial-torsional 90 degree OP test is most damaging which resulted in a shorter lifetime than the uniaxial OP test with the same Mises equivalent mechanical strain amplitude. A hold period at maximum temperatures reduced the lifetime for all tests regardless of the temperature

High temperature mechanical properties of unirradiated dispersion strengthened copper

International Nuclear Information System (INIS)

Gentzbittel, J.M.; Rigollet, C.; Robert, G.

1994-01-01

Oxide Dispersion Strengthened (ODS) copper material, due to its excellent thermal conductivity associated with a high temperature strength is a candidate material for structural applications as divertor plasma facing components of thermonuclear fusion reactor. Tensile and creep results of oxide dispersion strengthened copper are presented. The most important features of ODS copper high temperature behaviour are the high strength corresponding to low creep rates, high stress creep rate dependence, a poor ductility and a brittleness which result in a premature creep fracture at high applied stress. (R.P.) 2 refs.; 6 figs

Corrosion mechanisms and behaviour of actinides in the 'R7T7' nuclear glass

International Nuclear Information System (INIS)

Fillet, Sylvie

1987-01-01

This research thesis reports the study of aqueous corrosion of the R7T7 nuclear glass and of the identified corrosion mechanisms in conditions of static lixiviation which are close to that expected during long term storage in a geological environment. More specifically, this work aims at assessing the durability of this glass which has been selected for the vitrification of solutions from pressurized water reactors. The main glass alteration phenomena have been studied. The first part addresses the study of the alteration of the glassy matrix, and aims at identifying corrosion mechanisms in various lixiviation conditions (high temperature, saturation). The second part addresses the action of different materials present in the environment on the glassy matrix by simulating as well as possible a storage case. Based on the obtained results, a mathematical model is developed to predict the glass behaviour on the long term. Finally, the glass confinement power with respect to actinides is studied [fr

Silk-Quality, Spinnability and Low Temperature Behavior

Science.gov (United States)

2015-12-02

inert  atmosphere  (N2   gas   flow  rate  of  100  mL/min).  Changes   in  weight  percentage  during   temperature...Performance 3. DATES COVERED (From - To) 01-06-2012 to 31-05-2015 4. TITLE AND SUBTITLE Silk-Quality, Spinnability and Low Temperature Behaviour 5a...deploy the huge range in mechanical behaviour between different silk species and intra-species varieties. In particular, I set out to formulate a

Mechanical behaviour of uranium; Comportement mecanique de l'uranium

Energy Technology Data Exchange (ETDEWEB)

Bernard, J L; Coureau, G [Commissariat a l' Energie Atomique, Dir. Industrielle, Saclay (France). Centre d' Etudes Nucleaires

1957-07-01

The chief mechanical properties of uranium, taken at room and at different temperatures, are presented in this report. (author) [French] Dans ce rapport sont presentees les principales caracteristiques mecaniques de l'uranium, relevees a l'ambiante et a differentes temperatures. (auteur)

Stress-dislocation interaction mechanism in low-temperature thermo-compression sintering of Ag NPs

Science.gov (United States)

Wang, Fuliang; Tang, Zikai; He, Hu

2018-04-01

The sintering of metal nanoparticles (NPs) has been widely studied in the field of nanotechnology, and low-temperature sintering has become the industry standard. In this study, a molecular dynamics (MD) model was established to study the sintering behaviour of silver NPs during low-temperature thermo-compression. Primarily, we studied the sintering process, in which the ratio of neck radius to particle radius (x/r) changes. Under a uniaxial pressure, the maximum ratio in the temperature range 420-425 K was 1. According to the change of x/r, the process can be broken down into three stages: the neck-formation stage, neck-growth stage, and neck-stability stage. In addition, the relationship between potential energy, internal stress, and dislocation density during sintering is discussed. The results showed that cycling internal stress played an important role in sintering. Under the uniaxial pressure, the stress-dislocation interaction was found to be the major mechanism for thermo-compression sintering because the plastic deformation product dislocation intensified the diffusion of atoms. Also, the displacement vector, the mean square displacement, and the changing crystal structure during sintering were studied.

Stress-dislocation interaction mechanism in low-temperature thermo-compression sintering of Ag NPs

Directory of Open Access Journals (Sweden)

Fuliang Wang

2018-04-01

Full Text Available The sintering of metal nanoparticles (NPs has been widely studied in the field of nanotechnology, and low-temperature sintering has become the industry standard. In this study, a molecular dynamics (MD model was established to study the sintering behaviour of silver NPs during low-temperature thermo-compression. Primarily, we studied the sintering process, in which the ratio of neck radius to particle radius (x/r changes. Under a uniaxial pressure, the maximum ratio in the temperature range 420–425 K was 1. According to the change of x/r, the process can be broken down into three stages: the neck-formation stage, neck-growth stage, and neck-stability stage. In addition, the relationship between potential energy, internal stress, and dislocation density during sintering is discussed. The results showed that cycling internal stress played an important role in sintering. Under the uniaxial pressure, the stress-dislocation interaction was found to be the major mechanism for thermo-compression sintering because the plastic deformation product dislocation intensified the diffusion of atoms. Also, the displacement vector, the mean square displacement, and the changing crystal structure during sintering were studied.

Tribo-mechanical behaviour of SiC filled glass-epoxy composites at ...

African Journals Online (AJOL)

While glass fibers enhance the toughness of the matrix, silicon carbide shows high hardness, thermal stability and low chemical reactivity, leading to superior friction properties. In this work an attempt was made to evaluate the mechanical properties and tribological behaviour of glass fabric reinforced- epoxy (G-E) ...

Experimental characterization and modelling of UO2 mechanical behaviour at high temperatures and high strain rates

International Nuclear Information System (INIS)

Salvo, Maxime

2014-01-01

The aim of this work is to characterize and model the mechanical behavior of uranium dioxide (UO 2 ) during a Reactivity Initiated Accident (RIA). The fuel loading during a RIA is characterized by high strain rates (up to 1/s) and high temperatures (1000 C - 2500 C). Two types of UO 2 pellets (commercial and high density) were therefore tested in compression with prescribed displacement rates (0.1 to 100 mm/min corresponding to strain rates of 10 -4 - 10 -1 /s) and temperatures (1100 C - 1350 C - 1550 C et 1700 C). Experimental results (geometry, yield stress and microstructure) allowed us to define a hyperbolic sine creep law and a Drucker-Prager criterion with associated plasticity, in order to model grain boundaries fragmentation at the macroscopic scale. Finite Element Simulations of these tests and of more than 200 creep tests were used to assess the model response to a wide range of temperatures (1100 C - 1700 C) and strain rates (10 -9 /s - 10 -1 /s). Finally, a constitutive law called L3F was developed for UO 2 by adding to the previous model irradiation creep and tensile macroscopic cracking. The L3F law was then introduced in the 1.5D scheme of the fuel performance code ALCYONE-RIA to simulate the REP-Na tests performed in the experimental reactor CABRI. Simulation results are in good agreement with post tests examinations. (author) [fr

Mechanical behaviour of Zn-Fe alloy coated mild steel

International Nuclear Information System (INIS)

Panagopoulos, C.N.; Georgiou, E.P.; Agathocleous, P.E.; Giannakopoulos, K.I.

2009-01-01

Zinc alloy coatings containing various amounts of Fe were deposited by electrodeposition technique on a mild steel substrate. The concentration of Fe in the produced alloy coatings ranged from 0 to 14 wt.%, whereas the thickness of the coatings was about 50 μm. Structural and metallurgical characterization of the produced coatings was performed with the aid of X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) techniques. This study aims in investigating the mechanical behaviour of Zn-Fe coated mild steel specimens, as no research investigation concerning the tensile behaviour of Zn alloy coated ferrous alloys has been reported in the past. The experimental results indicated that the ultimate tensile strength of the Zn-Fe coated mild steel was lower than the bare mild steel. In addition, the ductility of the Zn-Fe coated mild steel was found to decrease significantly with increasing Fe content in the coating.

The role of water in the behaviour of concretes at high temperature

International Nuclear Information System (INIS)

Feraille-Fresnet, A.

2000-01-01

Since 1996, three fires have been counted in tunnels in Europe. During each of these accidents. the temperature reached by the structure has been estimated between 800 deg C and 1200 deg C. Beside these spectacular accidental situations, there are many other situations in which concrete structures are submitted to high temperatures during their regular use. Several research work has been undertaken for a better understanding of the behaviour of concrete submitted to high temperatures and the physical phenomena involved. This PhD Thesis takes down as part of this research work and develops, more particularly, the role of water in the material submitted to heating up to high temperatures. At first, we are interested in the role of water inside a material crack, during heating. We have established an original analytical solution giving the liquid-vapour repartition and the stress intensity factor, as functions of crack's length, water molecules contained in the inner of the crack and temperature. Then, we are able to study the crack stability. In the second part, we propose to approach the studied phenomena using the non saturated porous media theory. We present a thermo-hydro-chemical model which permits to describe the concrete behaviour under thermal loading. The material microstructure is defined using a 'porosimetric surface'. Each pore is characterised by two radii: the pore radius and the access radius into the pore. With this description, the zone of pores saturated by liquid is a state variable. We also introduce the concept of kinetic dehydration, clearly lighted by experimental studies. An hypothesis of erosion of the solid phase by dehydration permits to link the evolution of microstructure and of the zone of pores saturated by liquid to the mass of water created by dehydration. (author)

Effect of composition and technique of production, on the mechanical behaviour of based-zirconium metallic glasses

International Nuclear Information System (INIS)

Nowak, Sophie

2009-01-01

The metallic glasses are relatively new materials (50 years), produced by quenching a molten alloy. The amorphous structure of these materials gives them unique properties: very high strength (fracture stress is about 1.7 GPa for Zr based alloys), an elastic deformation reaching 2%, but little or no ductility. The compositions, which could produce both amorphous and bulk samples, are limited. The work, detailed in this manuscript, shows the possibility of sintering using SPS (Spark Plasma Sintering) amorphous powders obtained by atomization (Φaverage = 70 microns). The result is a fully densified and near fully amorphous sample. The optimization of this technique, with the composition Zr 57 Cu 20 Al 10 Ni 8 Ti 5 , gave samples for which mechanical behaviour is close to the bulk metallic glass behaviour. However, partial crystallization of the material occurs, localized at the contact points of particles, but could be reduced by deepening the sintering model outlined in this manuscript. In view of these results, new compositions are designed, and the production of ribbons was conducted. The characterization by nano-indentation estimates reliably the mechanical properties of these alloys. Finally, a new method, evaluating the activation volume, which is the elementary volume initiating plastic deformation, is presented. This technique is a statistical analysis of pseudo-creep tests performed by nano-indentation, at room temperature. In conclusion, this work opens new perspectives to develop bulk samples in broad range of compositions. (author)

Behaviour of neutron moderator materials at high temperatures in CASTOR registered -casks: qualification and assessment

International Nuclear Information System (INIS)

Krietsch, T.; Wolff, D.; Knopp, U.; Brocke, H.D.

2004-01-01

The Federal Institute for Materials Research and Testing (BAM) is the responsible German authority for the assessment of mechanical and thermal designs of transport and storage casks for radioactive materials. BAM checks up the proofs of the applicants in their safety reports and assesses the conformity to the Regulations for the Safe Transport of Radioactive Material. One applicant is the Gesellschaft fuer Nuklear-Behaelter mbH (GNB) with a new generation of transport and storage casks of CASTOR registered -design. GNB typically uses ultra high molecular weight Polyethylene (UHMW-PE) for the moderation of free neutrons. Rods made of UHMW-PE are positioned in axial bore holes in the wall of the cask and plates of UHMW-PE are in free spaces between primary and secondary lid and between the bottom of the cask and an outer plate (Figure 1). Because of the heat generated by the radioactive inventory and because of a strained spring at the bottom of every bore hole, UHMW-PE is subjected to permanent thermal and mechanical loads as well as loads from gamma and neutron radiation. UHMW-PE has been used under routine- and normal conditions of transport for maximum temperatures up to 130 C. For new generations of CASTOR registered -design maximum temperatures will be increased up to 160 C. That means a permanent use of UHMW-PE at temperatures within and above the melting region of the crystallites. In this paper, some results of special investigations for the proofs of usability of UHMW-PE at temperatures up to 160 C under real conditions of transport and storage in CASTOR registered -casks are given. For that, investigations on temperature dependent expansion behaviour under laboratory conditions as well as in large scale experiments, especially in the case of multiple heating and cooling, were done. Besides, geometrical creep strength for long-term loading by temperatures and pressures with regard to the chemical and physical stability properties of UHMW-PE above the

Temperature-dependence of creep behaviour of dental resin-composites.

Science.gov (United States)

El-Safty, S; Silikas, N; Watts, D C

2013-04-01

To determine the effect of temperature, over a clinically relevant range, on the creep behaviour of a set of conventional and flowable resin-composites including two subgroups having the same resin matrix and varied filler loading. Eight dental resin-composites: four flowable and four conventional were investigated. Stainless steel split moulds (4 mm × 6 mm) were used to prepare cylindrical specimens for creep examination. Specimens were irradiated in the moulds in layers of 2mm thickness (40s each), as well as from the radial direction after removal from the moulds, using a light-curing unit with irradiance of 650 mW/cm(2). A total of 15 specimens from each material were prepared and divided into three groups (n=5) according to the temperature; Group I: (23°C), Group II: (37°C) and Group III: (45°C). Each specimen was loaded (20 MPa) for 2h and unloaded for 2h. Creep was measured continuously over the loading and unloading periods. At higher temperatures greater creep and permanent set were recorded. The lowest mean creep occurred with GS and GH resin-composites. Percentage of creep recovery decreased at higher temperatures. At 23°C, the materials exhibited comparable creep. At 37°C and 45°C, however, there was a greater variation between materials. For all resin-composites, there was a strong linear correlation with temperature for both creep and permanent set. Creep parameters of resin-composites are sensitive to temperature increase from 23 to 45°C, as can occur intra-orally. For a given resin matrix, creep decreased with higher filler loading. Copyright © 2012 Elsevier Ltd. All rights reserved.

Correlation between microstructure and the creep behaviour at high temperature of Alloy 800 H

International Nuclear Information System (INIS)

Spiradek, K.; Degischer, H.P.; Lahodny, H.

1989-01-01

A systematic metallographic study was performed to identify the nature of the microstructural changes occurring during high temperature creep deformation of Alloy 800 H. Creep tests were carried out at 800 deg. C under constant load conditions corresponding to the initial stresses between 25 and 80 MPa. Some tests were interrupted after certain elongations to provide the samples for electron microscopy. Emphasis was put on the creep periods relevant to design where only a few per cent of deformation are tolerable. The influence of the initial material conditions on the creep behaviour was examined. Variations of the initial microstructures were achieved by different solution treatments (980/1250) deg. C, preageing at 800 deg. C (0/6400) h and cold deformation up to 10% followed by ageing at 800 deg. C. The results of the microstructural examinations were correlated with the creep curves that provide a basis for identification of the creep mechanisms operating at the test conditions. (author). 14 refs, 17 figs

Physiological mechanisms underlying animal social behaviour.

Science.gov (United States)

Seebacher, Frank; Krause, Jens

2017-08-19

Many species of animal live in groups, and the group represents the organizational level within which ecological and evolutionary processes occur. Understanding these processes, therefore, relies on knowledge of the mechanisms that permit or constrain group formation. We suggest that physiological capacities and differences in physiology between individuals modify fission-fusion dynamics. Differences between individuals in locomotor capacity and metabolism may lead to fission of groups and sorting of individuals into groups with similar physiological phenotypes. Environmental impacts such as hypoxia can influence maximum group sizes and structure in fish schools by altering access to oxygenated water. The nutritional environment determines group cohesion, and the increase in information collected by the group means that individuals should rely more on social information and form more cohesive groups in uncertain environments. Changing environmental contexts require rapid responses by individuals to maintain group coordination, which are mediated by neuroendocrine signalling systems such as nonapeptides and steroid hormones. Brain processing capacity may constrain social complexity by limiting information processing. Failure to evaluate socially relevant information correctly limits social interactions, which is seen, for example, in autism. Hence, functioning of a group relies to a large extent on the perception and appropriate processing of signals from conspecifics. Many if not all physiological systems are mechanistically linked, and therefore have synergistic effects on social behaviour. A challenge for the future lies in understanding these interactive effects, which will improve understanding of group dynamics, particularly in changing environments.This article is part of the themed issue 'Physiological determinants of social behaviour in animals'. © 2017 The Author(s).

On the mechanical behaviours of a craze in particulate-polymer composites

Science.gov (United States)

Zhang, Y. M.; Zhang, W. G.; Fan, M.; Xiao, Z. M.

2018-05-01

In polymeric composites, well-defined inclusions are incorporated into the polymer matrix to alleviate the brittleness of polymers. When a craze is initiated in such a composite, the interaction between the craze and the surrounding inclusions will greatly affect the composite's mechanical behaviours and toughness. To the best knowledge of the authors, only little research work has been found so far on the interaction between a craze and the near-by inclusions in particulate-polymer composites. In the current study, the first time, the influences of the surrounding inclusions on the craze are investigated in particulate-polymer composites. The three-phase model is adopted to study the fracture behaviours of the craze affected by multiple inclusions. An iterative procedure is proposed to solve the stress intensity factors. Parametric studies are performed to investigate the influences of the reinforcing particle volume fraction and the shear modulus ratio on fracture behaviours of particulate-polymer composites.

Robust design of microelectronics assemblies against mechanical shock, temperature and moisture effects of temperature, moisture and mechanical driving forces

CERN Document Server

Wong, E-H

2015-01-01

Robust Design of Microelectronics Assemblies Against Mechanical Shock, Temperature and Moisture discusses how the reliability of packaging components is a prime concern to electronics manufacturers. The text presents a thorough review of this important field of research, providing users with a practical guide that discusses theoretical aspects, experimental results, and modeling techniques. The authors use their extensive experience to produce detailed chapters covering temperature, moisture, and mechanical shock induced failure, adhesive interconnects, and viscoelasticity. Useful progr

Effect of gender on physiological and behavioural responses of Gammarus roeseli (Crustacea Amphipoda) to salinity and temperature

International Nuclear Information System (INIS)

Sornom, Pascal; Felten, Vincent; Medoc, Vincent; Sroda, Sophie; Rousselle, Philippe; Beisel, Jean-Nicolas

2010-01-01

The importance of potentially interacting factors in organisms responses to a stress are often ignored or underestimated in ecotoxicology. In laboratory experiments we investigated how gender, temperature and age influence the behaviour and the physiology of the freshwater amphipod Gammarus roeseli under salinity stress. Our results revealed a significant higher sensitivity of females in survival, ventilation and ionoregulation whereas no inter-age differences were reported. Water temperature also exerted a significant effect in survival and ventilation of G. roeseli. Some of those factors appeared to interact significantly. This study provides evidence that gender can affect organisms responses to a stressor and consequently has to be considered while assessing a stress impact. We discussed the potential relationships between biological and behavioural responses. - Influence of gender, age and temperature in a gammarid responses to a stress.

High Temperature Electro-Mechanical Devices For Nuclear Applications

International Nuclear Information System (INIS)

Robertson, D.

2010-01-01

Nuclear power plants require a number of electro-mechanical devices, for example, Control Rod Drive Mechanisms (CRDM's) to control the raising and lowering of control rods and Reactor Coolant Pumps (RCP's) to circulate the primary coolant. There are potential benefits in locating electro-mechanical components in areas of the plant with high ambient temperatures. One such benefit is the reduced need to make penetrations in pressure vessels leading to simplified plant design and improved inherent safety. The feature that limits the ambient temperature at which most electrical machines may operate is the material used for the electrical insulation of the machine windings. Conventional electrical machines generally use polymer-based insulation that limits the ambient temperature they can operate in to below 200 degrees Celsius. This means that when a conventional electrical machine is required to operate in a hot area it must be actively cooled necessitating additional systems. This paper presents data gathered during investigations undertaken by Rolls-Royce into the design of high temperature electrical machines. The research was undertaken at Rolls-Royce's University Technology Centre in Advanced Electrical Machines and Drives at Sheffield University. Rolls- Royce has also been investigating high temperature wire and encapsulants and latterly techniques to provide high temperature insulation to terminations. Rolls-Royce used the experience gained from these tests to produce a high temperature electrical linear actuator at sizes representative of those used in reactor systems. This machine was tested successfully at temperatures equivalent to those found inside the reactor vessel of a pressurised water reactor through a full series of operations that replicated in service duty. The paper will conclude by discussing the impact of the findings and potential electro-mechanical designs that may utilise such high temperature technologies. (authors)

Corrosion behaviour of Alloy 800 in high temperature aqueous solutions: Electrochemical studies

International Nuclear Information System (INIS)

Olmedo, A.M.; Villegas, M.; Alvarez, M.G.

1996-01-01

The anodic behaviour and passivity breakdown of Alloy 800 in aqueous solutions of sodium chloride, sodium sulphate and sodium bicarbonate were studied by electrochemical techniques in the temperature range from 60 C to 280 C. The pitting resistance and pitting morphology of the alloy in chloride plus sulphate and chloride plus bicarbonate mixtures, at 60 C and 280 C, were also examined. Increasing bicarbonate or sulphate additions to chloride solutions shift the characteristic pitting potential of Alloy 800 to higher values, both at low and high temperatures. Changes in pitting morphology were observed in sulphate containing solutions while the morphology of the attack found in bicarbonate containing solutions was similar to that in pure chloride solutions. Finally, no localized or substantial generalized corrosion was detected in pure sulphate or bicarbonate solutions at any temperature. (orig.)

A novel method for delivering ramped cooling reveals rat behaviours at innocuous and noxious temperatures: A comparative study of human psychophysics and rat behaviour.

Science.gov (United States)

Dunham, James P; Hulse, Richard P; Donaldson, Lucy F

2015-07-15

Thermal sensory testing in rodents informs human pain research. There are important differences in the methodology for delivering thermal stimuli to humans and rodents. This is particularly true in cold pain research. These differences confound extrapolation and de-value nociceptive tests in rodents. We investigated cooling-induced behaviours in rats and psychophysical thresholds in humans using ramped cooling stimulation protocols. A Peltier device mounted upon force transducers simultaneously applied a ramped cooling stimulus whilst measuring contact with rat hind paw or human finger pad. Rat withdrawals and human detection, discomfort and pain thresholds were measured. Ramped cooling of a rat hind paw revealed two distinct responses: Brief paw removal followed by paw replacement, usually with more weight borne than prior to the removal (temperature inter-quartile range: 19.1 °C to 2.8 °C). Full withdrawal was evoked at colder temperatures (inter quartile range: -11.3 °C to -11.8 °C). The profile of human cool detection threshold and cold pain threshold were remarkably similar to that of the rat withdrawals behaviours. Previous rat cold evoked behaviours utilise static temperature stimuli. By utilising ramped cold stimuli this novel methodology better reflects thermal testing in patients. Brief paw removal in the rat is driven by non-nociceptive afferents, as is the perception of cooling in humans. This is in contrast to the nociceptor-driven withdrawal from colder temperatures. These findings have important implications for the interpretation of data generated in older cold pain models and consequently our understanding of cold perception and pain. Copyright © 2015. Published by Elsevier B.V.

Thermal and mechanical behaviour of sub micron sized fly ash reinforced polyester resin composite

Science.gov (United States)

Nantha Kumar, P.; Rajadurai, A.; Muthuramalingam, T.

2018-04-01

The utilization of particles reinforced resin matrix composites is being increased owing to its lower density and high strength to weight ratio. In the present study, an attempt has been made to synthesize fly ash particles reinforced polyester resin composite for engine cowling application. The thermal stability and mechanical behaviours such as hardness and flexural strength of the composite with 2, 3 and 4 weight % of reinforcement is studied and analyzed. The thermo gravimetric analysis indicates that the higher addition of reinforcement increases the decomposition temperature due to its refractory nature. It is also observed that the hardness increases with higher filler addition owing to the resistance of FA particles towards penetration. The flexural strength is found to increase up to the addition of 3% of FA particles, whereas the polyester resin composite prepared with 4% FA particles addition is observed to have low flexural strength owing to agglomeration of particles.

Mechanical, thermal, rheological and morphological behaviour of irradiated PP/HA composites

International Nuclear Information System (INIS)

Ramirez, C.; Albano, C.; Karam, A.; Dominguez, N.; Sanchez, Y.; Gonzalez, G.

2005-01-01

Hydroxyapatite (HA) reinforced polypropylene (PP) composites are being developed as bone graft materials. In this research, the effect of γ irradiation on mechanical, rheological, thermal and morphological behaviour of PP-HA composites was studied. The melt flow index of polymer increased markedly when it was exposed to radiation. This is indicative of chain scission reaction as the predominant process. During the tensile testing, the composites exhibited brittle behaviour, showing no fluency point. Elongation at break showed a tendency to decrease with the increase in radiation dose while stress at break did not show significant variation with radiation dose. High HA content (>20%) and radiation dose (25 kGy) had significant influence on thermal stability

Flexural creep behaviour of jute polypropylene composites

Science.gov (United States)

Chandekar, Harichandra; Chaudhari, Vikas

2016-09-01

Present study is about the flexural creep behaviour of jute fabric reinforced polypropylene (Jute-PP) composites. The PP sheet and alkali treated jute fabric is stacked alternately and hot pressed in compression molding machine to get Jute-PP composite laminate. The flexural creep study is carried out on dynamic mechanical analyzer. The creep behaviour of the composite is modeled using four-parameter Burgers model. Short-term accelerated creep testing is conducted which is later used to predict long term creep behaviour. The feasibility of the construction of a master curve using the time-temperature superposition (TTS) principle to predict long term creep behavior of unreinforced PP and Jute-PP composite is investigated.

Experimental study of mechanical behaviour of a clay-stone: application to nuclear waste disposals

International Nuclear Information System (INIS)

Chiarelli, A.S.; Shao, J.F.; Ledesert, B.; Hoteit, N.

2001-01-01

A study of mechanical behaviour of deep argillaceous rocks from East of France, the 'argilites de l'Est' as a potential host rock for radioactive waste disposal studied by ANDRA, (french national radioactive waste management agency) is presented. Some uniaxial and triaxial compression tests with unloading-reloading cycles were realised on samples from three different depths. Important plastic strains associated to directional degradation of elastic properties show that the two principles strain mechanisms are plasticity and induced anisotropic damage. At microscopic scale, it is related to sliding of clay sheets and oriented microcracks. The influence of mineralogy is that brittle behaviour is more important with calcite while it decreases with clay. (authors)

Opto-mechanical subsystem with temperature compensation through isothemal design

Science.gov (United States)

Goodwin, F. E. (Inventor)

1977-01-01

An opto-mechanical subsystem for supporting a laser structure which minimizes changes in the alignment of the laser optics in response to temperature variations is described. Both optical and mechanical structural components of the system are formed of the same material, preferably beryllium, which is selected for high mechanical strength and good thermal conducting qualities. All mechanical and optical components are mounted and assembled to provide thorough thermal coupling throughout the subsystem to prevent the development of temperature gradients.

TEMPERATURE HETEROGENEITY OF TRAVELLING FIRE AND ITS INFLUENCE ON COMPOSITE STEEL-CONCRETE FLOOR

Directory of Open Access Journals (Sweden)

Kamila Horová

2016-04-01

Full Text Available In order to follow modern trends in contemporary building architecture, which is moving off the limits of current fire design models, assumption of homogeneous temperature conditions used for structural fire analysis needs to be revised. In this paper fire dynamics of travelling fire is investigated experimentally by conducting fire test in two-storey experimental building. To evaluate the impact of travelling fire on the mechanical behaviour of a structure, the spatial and temporal evolution of the gas temperature calculated in NIST code FDS, which was validated to experimental measurements, is applied to the composite floor of dimensions 9.0 m by 9.0 m. Mechanical behaviour of the composite slab highly affected by regions of high temperatures and areas with only elevated temperatures is solved in code Vulcan. To highlight the severity of spreading fire causing non-uniform temperature conditions, which after-effects differ from traditional methods, a comparison of both methods is introduced. The calculation of mechanical behaviour of the composite floor is repeated in a series of three different thermal loading cases. Results of all cases are then compared in terms of vertical displacement and axial force in several positions of the composite floor.

Mechanical and wear behaviour of steel chips reinforced Zn27Al composites

Directory of Open Access Journals (Sweden)

Kenneth Kanayo ALANEME

2016-12-01

Full Text Available The mechanical and wear behaviour of Zn27Al alloy reinforced with steel machining chips (an industrial waste was investigated. Two step stir casting process was used to produce the Zn27Al based composites consisting of 5, 7.5 and 10 wt.% of the steel machining chips while unreinforced Zn27Al alloy and a composition consisting of 5 wt.% alumina were also prepared as control samples. Microstrutural analysis; mechanical and wear behaviour were assessed for these composites. The results show that the hardness and wear resistance of the composites increased with increase in weight percent of the steel chips from 5 to 10 wt.%. The UTS, strain to fracture, and the fracture toughness were however highest for the 5 wt.% steel chips reinforced composite grade; and decreased with increase in the weight percent of the steel chips from 5 to 10 wt.%. Generally the Zn27Al alloy based composites reinforced with steel machining chips, exhibited superior mechanical and wear properties in comparison to the unreinforced Zn27Al alloy and the 5 wt.% alumina reinforced Zn27Al alloy composite.

An overview of the Indian program related to fast reactor core mechanical behaviour

International Nuclear Information System (INIS)

Govindarajan, S.; Bhoje, S.B.; Paranjpe, S.R.

1984-01-01

This Indian review paper presents the evolution of the fast breeder program which began with fast breeder test reactor (FBTR) commencing in 1972. The state-of-art in the field of core mechanical behaviour is reviewed

Mechanical Behaviour of the Wood Masonry

Directory of Open Access Journals (Sweden)

Fazia FOUCHAL

2011-09-01

Full Text Available In this paper we study the walls wood masonry behaviour. First, we propose a regulatory validation of the walls wood masonry behaviour subjected to vertical and horizontal loads according to Eurocode 5. Then we present the numerical application on the wall wood supported two floors level.

Empathy as a driver of prosocial behaviour: highly conserved neurobehavioural mechanisms across species

Science.gov (United States)

Decety, Jean; Bartal, Inbal Ben-Ami; Uzefovsky, Florina; Knafo-Noam, Ariel

2016-01-01

Empathy reflects the natural ability to perceive and be sensitive to the emotional states of others, coupled with a motivation to care for their well-being. It has evolved in the context of parental care for offspring, as well as within kinship bonds, to help facilitate group living. In this paper, we integrate the perspectives of evolution, animal behaviour, developmental psychology, and social and clinical neuroscience to elucidate our understanding of the proximate mechanisms underlying empathy. We focus, in particular, on processing of signals of distress and need, and their relation to prosocial behaviour. The ability to empathize, both in animals and humans, mediates prosocial behaviour when sensitivity to others' distress is paired with a drive towards their welfare. Disruption or atypical development of the neural circuits that process distress cues and integrate them with decision value leads to callous disregard for others, as is the case in psychopathy. The realization that basic forms of empathy exist in non-human animals is crucial for gaining new insights into the underlying neurobiological and genetic mechanisms of empathy, enabling translation towards therapeutic and pharmacological interventions. PMID:26644596

Mechanical and structural behaviour of uranium α, β, γ phases during plastic deformation

International Nuclear Information System (INIS)

Prunier, C.; Collot, C.

1981-06-01

High temperature behaviour of rich and poor uranium alloys in α, β and γ crystalline structures is studied: dynamic recrystallization phenomena begins only in α and β phases high temperature range, high strength and brittle β phase shows a very large ductility above 700 0 C. Dynamic recrystallization in γ phase rich alloys is observed only if large energy is available. Recrystallization is a thermal actived phenomena localised at grain boundary, dependant with alloy concentration and crystalline structure. β phase activation energy and deformation rate for dynamic recrystallization beginning are the most important in relation with structure complexity; both temperature and rate deformation are dynamic recrystallization factors [fr

Material characterisation and preliminary mechanical design for the HL-LHC shielded beam screens operating at cryogenic temperatures

CERN Document Server

Garion, C; Koettig, T; Machiocha, W; Morrone, M

2015-01-01

The High Luminosity LHC project (HL-LHC) aims at increasing the luminosity (rate of collisions) in the Large Hadron Collider (LHC) experiments by a factor of 10 beyond the original design value (from 300 to 3000 fb-1). It relies on new superconducting magnets, installed close to the interaction points, equipped with new beam screen. This component has to ensure the vacuum performance together with shielding the cold mass from physics debris and screening the cold bore cryogenic system from beam induced heating. The beam screen operates in the range 40-60 K whereas the magnet cold bore temperature is 1.9 K. A tungsten-based material is used to absorb the energy of particles. In this paper, measurements of the mechanical and physical properties of such tungsten material are shown at room and cryogenic temperature. In addition, the design and the thermal mechanical behaviour of the beam screen assembly are presented also. They include the heat transfer from the tungsten absorbers to the cooling pipes and the sup...

Isobaric thermal expansivity behaviour against temperature and pressure of associating fluids

Energy Technology Data Exchange (ETDEWEB)

Navia, Paloma; Troncoso, Jacobo [Departamento de Fisica Aplicada, Facultad de Ciencias de Ourense, Campus As Lagoas, 32004 Ourense (Spain); Romani, Luis, E-mail: romani@uvigo.e [Departamento de Fisica Aplicada, Facultad de Ciencias de Ourense, Campus As Lagoas, 32004 Ourense (Spain)

2010-01-15

In order to study the influence of association on the isobaric thermal expansivity, this magnitude has been experimentally determined for a set of associating fluids within the temperature and pressure intervals (278.15 to 348.15) K and (5 to 55) MPa by means of calorimetric measurements. The 1-alcohol series, from methanol to 1-decanol, 2-pentanol, 3-pentanol, and 1-pentylamine were selected. With a view on checking the quality of the experimental data, they are compared with available literature values; good coherence was obtained for most of the studied liquids. The analysis of the experimental results reveals that the association capability presents a strong influence not only on the value of the isobaric thermal expansivity itself, but also on its behaviour against temperature and pressure.

Isobaric thermal expansivity behaviour against temperature and pressure of associating fluids

International Nuclear Information System (INIS)

Navia, Paloma; Troncoso, Jacobo; Romani, Luis

2010-01-01

In order to study the influence of association on the isobaric thermal expansivity, this magnitude has been experimentally determined for a set of associating fluids within the temperature and pressure intervals (278.15 to 348.15) K and (5 to 55) MPa by means of calorimetric measurements. The 1-alcohol series, from methanol to 1-decanol, 2-pentanol, 3-pentanol, and 1-pentylamine were selected. With a view on checking the quality of the experimental data, they are compared with available literature values; good coherence was obtained for most of the studied liquids. The analysis of the experimental results reveals that the association capability presents a strong influence not only on the value of the isobaric thermal expansivity itself, but also on its behaviour against temperature and pressure.

Mechanical and water absorption behaviour of banana/sisal reinforced hybrid composites

International Nuclear Information System (INIS)

Venkateshwaran, N.; ElayaPerumal, A.; Alavudeen, A.; Thiruchitrambalam, M.

2011-01-01

Highlights: → It explores the utilization of waste banana fiber. → Improving the mechanical property by hybridization. → Results show its usefulness to low cost application. -- Abstract: The tensile, flexural, impact and water absorption tests were carried out using banana/epoxy composite material. Initially, optimum fiber length and weight percentage were determined. To improve the mechanical properties, banana fiber was hybridised with sisal fiber. This study showed that addition of sisal fiber in banana/epoxy composites of up to 50% by weight results in increasing the mechanical properties and decreasing the moisture absorption property. Morphological analysis was carried out to observe fracture behaviour and fiber pull-out of the samples using scanning electron microscope.

Analysis of the thermo-mechanical behaviour of the DEMO Water-Cooled Lithium Lead breeding blanket module under normal operation steady state conditions

Energy Technology Data Exchange (ETDEWEB)

Di Maio, P.A.; Arena, P. [Dipartimento di Energia, Ingegneria dell’Informazione e Modelli Matematici, Università di Palermo, Viale delle Scienze, 90128 Palermo (Italy); Aubert, J. [CEA Saclay, DEN/DANS/DM2S/SEMT, 91191 Gif sur Yvette Cedex (France); Bongiovì, G. [Dipartimento di Energia, Ingegneria dell’Informazione e Modelli Matematici, Università di Palermo, Viale delle Scienze, 90128 Palermo (Italy); Chiovaro, P., E-mail: pierluigi.chiovaro@unipa.it [Dipartimento di Energia, Ingegneria dell’Informazione e Modelli Matematici, Università di Palermo, Viale delle Scienze, 90128 Palermo (Italy); Giammusso, R. [ENEA – C.R. Brasimone, 40032 Camugnano (Italy); Li Puma, A. [CEA Saclay, DEN/DANS/DM2S/SEMT, 91191 Gif sur Yvette Cedex (France); Tincani, A. [ENEA – C.R. Brasimone, 40032 Camugnano (Italy)

2015-10-15

Highlights: • A DEMO WCLL blanket module thermo-mechanical behaviour has been investigated. • Two models of the WCLL blanket module have been set-up adopting a code based on FEM. • The water flow domain in the module has been considered. • A set of uncoupled steady state thermo-mechanical analyses has been carried out. • Critical temperature is not overcome. Safety verifications are generally satisfied. - Abstract: Within the framework of DEMO R&D activities, a research cooperation has been launched between ENEA, the University of Palermo and CEA to investigate the thermo-mechanical behaviour of the outboard equatorial module of the DEMO1 Water-Cooled Lithium Lead (WCLL) blanket under normal operation steady state scenario. The research campaign has been carried out following a theoretical–computational approach based on the Finite Element Method (FEM) and adopting a qualified commercial FEM code. In particular, two different 3D FEM models (Model 1 and Model 2), reproducing respectively the central and the lateral poloidal–radial slices of the WCLL blanket module, have been set up. A particular attention has been paid to the modelling of water flow domain, within both the segment box channels and the breeder zone tubes, to simulate realistically the coolant-box thermal coupling. Results obtained are herewith reported and critically discussed.

Magnetic shape memory behaviour

International Nuclear Information System (INIS)

Brown, P.J.; Gandy, A.P.; Ishida, K.; Kainuma, R.; Kanomata, T.; Matsumoto, M.; Morito, H.; Neumann, K.-U.; Oikawa, K.; Ouladdiaf, B.; Ziebeck, K.R.A.

2007-01-01

Materials that can be transformed at one temperature T F , then cooled to a lower temperature T M and plastically deformed and on heating to T F regain their original shape are currently receiving considerable attention. In recovering their shape the alloys can produce a displacement or a force, or a combination of the two. Such behaviour is known as the shape memory effect and usually takes place by change of temperature or applied stress. For many applications the transformation is not sufficiently rapid or a change in temperature/pressure not appropriate. As a result, considerable effort is being made to find a ferromagnetic system in which the effect can be controlled by an applied magnetic field. The results of recent experiments on ferromagnetic shape memory compounds aimed at understanding the underlying mechanism will be reviewed

Low-temperature behaviour of an ideal Bose gas and some forbidden thermodynamic cycles

International Nuclear Information System (INIS)

Chen Jincan; Lin Bihong

2003-01-01

Based on the equation of state of an ideal Bose gas, the heat capacities at constant volume and constant pressure of the Bose system are derived and used to analyse the low-temperature behaviour of the Bose system. It is expounded that some important thermodynamic processes such as a constant pressure and an adiabatic process cannot be carried out from the region of T > T c to that of T c , where T c is the critical temperature of Bose-Einstein condensation of the Bose system. Consequently, some typical thermodynamic cycles such as the Carnot cycle, Brayton cycle, Otto cycle, Ericsson cycle, Diesel cycle and Atkinson cycle cannot be operated across the critical temperature T c of Bose-Einstein condensation of an ideal Bose gas

High temperature corrosion of metals

International Nuclear Information System (INIS)

Quadakkers, W.J.; Schuster, H.; Ennis, P.J.

1988-08-01

This paper covers three main topics: 1. high temperature oxidation of metals and alloys, 2. corrosion in sulfur containing environments and 3. structural changes caused by corrosion. The following 21 subjects are discussed: Influence of implanted yttrium and lanthanum on the oxidation behaviour of beta-NiA1; influence of reactive elements on the adherence and protective properties of alumina scales; problems related to the application of very fine markers in studying the mechanism of thin scale formation; oxidation behaviour of chromia forming Co-Cr-Al alloys with or without reactive element additions; growth and properties of chromia-scales on high-temperature alloys; quantification of the depletion zone in high temperature alloys after oxidation in process gas; effects of HC1 and of N2 in the oxidation of Fe-20Cr; investigation under nuclear safety aspects of Zircaloy-4 oxidation kinetics at high temperatures in air; on the sulfide corrosion of metallic materials; high temperature sulfide corrosion of Mn, Nb and Nb-Si alloys; corrosion behaviour or NiCrAl-based alloys in air and air-SO2 gas mixtures; sulfidation of cobalt at high temperatures; preoxidation for sulfidation protection; fireside corrosion and application of additives in electric utility boilers; transport properties of scales with complex defect structures; observations of whiskers and pyramids during high temperature corrosion of iron in SO2; corrosion and creep of alloy 800H under simulated coal gasification conditions; microstructural changes of HK 40 cast alloy caused by exploitation in tubes in steam reformer installation; microstructural changes during exposure in corrosive environments and their effect on mechanical properties; coatings against carburization; mathematical modeling of carbon diffusion and carbide precipitation in Ni-Cr-based alloys. (MM)

Thermo-mechanical fatigue behaviour and life prediction of C-1023 ...

African Journals Online (AJOL)

user

Mechanical strain-cycles to failure curves for 890-1055 ºC temperature range. ... could be ascribed to creep strain accumulation at high temperatures coinciding ... It is common in engineering applications to rely on life prediction models based ...

Effect of transient change in strain rate on plastic flow behaviour of ...

Indian Academy of Sciences (India)

Steels; stress–strain measurement; plastic flow; mechanical properties; metallurgy. Abstract. Plastic flow behaviour of low carbon steel has been studied at room temperature during tensile deformation by ... Bulletin of Materials Science | News.

Physiological control of behaviour in tephritid fruit flies

International Nuclear Information System (INIS)

Jang, Eric B.

2000-01-01

Studies on the behaviour of tephritid fruit flies have historically focused on the interaction of external stimuli such as temperature, semiochemicals, seasonality, etc., or the interactions of flies between and among species for a number of observed behaviours such as mating, pheromone calling and oviposition. While descriptive behaviour represent much of what we know about these pest species, less is known about the underlying physiological mechanisms which function in priming or modulation of the observed behaviour. Central to our understanding of tephritid behaviour are the multiple and often complex internal factors which are involved, and the path/mechanisms by which external stimuli result in observed behaviour. Tephritid fruit fly physiology is a vastly understudied research area which may provide important information on how peripheral receptors receive information, the transduction and coding of information centrally and how behaviour is regulated biochemically. The integration of physiology disciplines to help explain behaviour is central to the goal of developing new technology which may be useful in fruit fly control. In our laboratory, we have been studying the mechanisms of chemoreception and its link to behaviour in tephritids in such areas as olfaction, feeding, mating and oviposition. Our approach has been that tephritid behaviour can be largely influenced by their peripheral receptors which are responsible for receiving olfactory, gustatory, visual and tactile information inputs and their physiological state which controls internal modulation of behaviour. Thus, differences in behaviour between species might be explained on the basis of differences in their peripheral receptors, and the plasticity in which observed behaviour vary between the same species could very well be attributed to changes in their physiological state that are not readily apparent merely from visual observation. The importance of the physiological state in behavioural

Analysis of elevated temperature flow and work hardening behaviour of service-exposed 2.25Cr-1Mo steel using Voce equation

International Nuclear Information System (INIS)

Girish Shastry, C.; Mathew, M.D.; Bhanu Sankara Rao, K.; Mannan, S.L.

2004-01-01

The Voce equation was used to model the tensile flow and work-hardening behaviour of a service-exposed 2.25Cr-1Mo steel. The applicability of Voce parameters obtained from the fit to experimental true stress-true strain datasets for estimating the validity of the fit was examined. The Voce equation was found to model the stress-strain curve closely. The Voce parameter n v was correlated to the underlying dislocation activities. It was found that the values of Voce parameters at various temperatures and strain rates can be used to infer the operating recovery mechanism during stage III hardening. A low absolute value of n v is indicative of recovery by cross-slip, whereas the high temperature transition to climb or sub-boundary migration driven recovery is accompanied by an increase in the value of n v

Sex differences and serotonergic mechanisms in the behavioural effects of psilocin.

Science.gov (United States)

Tylš, Filip; Páleníček, Tomáš; Kadeřábek, Lukáš; Lipski, Michaela; Kubešová, Anna; Horáček, Jiří

2016-06-01

Psilocybin has recently attracted a great deal of attention as a clinical research and therapeutic tool. The aim of this paper is to bridge two major knowledge gaps regarding its behavioural pharmacology - sex differences and the underlying receptor mechanisms. We used psilocin (0.25, 1 and 4 mg/kg), an active metabolite of psilocybin, in two behavioural paradigms - the open-field test and prepulse inhibition (PPI) of the acoustic startle reaction. Sex differences were evaluated with respect to the phase of the female cycle. The contribution of serotonin receptors in the behavioural action was tested in male rats with selective serotonin receptor antagonists: 5-HT1A receptor antagonist (WAY100635 1 mg/kg), 5-HT2A receptor antagonist (MDL100907 0.5 mg/kg), 5-HT2B receptor antagonist (SB215505 1 mg/kg) and 5-HT2C receptor antagonist (SB242084 1 mg/kg). Psilocin induced dose-dependent inhibition of locomotion and suppression of normal behaviour in rats (behavioural serotonin syndrome, impaired PPI). The effects were more pronounced in male rats than in females. The inhibition of locomotion was normalized by 5-HT1A and 5-HT2B/C antagonists; however, PPI was not affected significantly by these antagonists. Our findings highlight an important issue of sex-specific reactions to psilocin and that apart from 5-HT2A-mediated effects 5-HT1A and 5-HT2C/B receptors also play an important role. These findings have implications for recent clinical trials.

Evolution of fuel rod support under irradiation impact on the mechanical behaviour of fuel assemblies

International Nuclear Information System (INIS)

Billerey, Antoine; Waeckel, Nicolas

2005-01-01

New fuel management targets imply to increase fuel assembly discharge burnup. Therefore, the prediction of the mechanical behaviour of the irradiated fuel assembly is essential such as excessive fuel assembly distortion induce incomplete Rod Cluster Control Assembly insertion problems (safety issue) or fuel rod vibration induced wear leading to leaking rods (plant operation problems). Within this framework, one of the most important parameter is the knowledge of the fuel rod support in the grid cell because it directly governs the mechanical behaviour of the fuel assembly and consequently allows to predict the behaviour of irradiated structures in terms of (1) axial and lateral deformation (global behaviour of the assembly) and (2) rod vibration induced wear (local behaviour of the rod). Generally, fuel rod support is provided by a spring-dimple system fixed to the grid. During irradiation, the spring force decreases and a gap between the rod and the spring may occur. This phenomenon is due to (1) stress relieving in the spring and in the dimples, (2) grid growth and (3) reduction of the rod diameter. Two models have been developed to predict the behaviour of the rod in the cell. The first model is dedicated to the evaluation of the spring force relaxation during irradiation. The second one can assess the rotation characteristic of the fuel rod in the cell, function of the spring force. The main input parameters are (1) the creep laws of the grid materials, (2) the growth law of the grid, (3) the evolution of rod diameter and (4) the design of the fuel rod support. The aim of this paper is to: (1) evaluate the consequences of grid support design modifications on the rod vibration sensitivity in terms of predicted rod to grid maximum gap during irradiation and time in operation with an open rod to grid gap, (2) evaluate, using a linear or non-linear Finite Element assembly model, the impact of the evolution of grid support under irradiation on the overall mechanical

Thermal shock behaviour of SiC-fibre-reinforced glasses

International Nuclear Information System (INIS)

Klug, T.; Reichert, J.; Brueckner, R.

1992-01-01

The preparation of two SiC-fibre-reinforced glasses with very different thermal expansion coefficients and glass transition temperatures is described and the influence of long-time temperature and thermal shock behaviour of these composites on the mechanical properties is investigated by means of bending test experiments before and after thermal treatments. It will be shown from experiments and calculations on stresses due to thermal expansion mismatch between fibre and glass matrix that not only best mechanical properties but also best thermal shock behaviour are connected with low tensile intrinsic stresses produced by thermal expansion mismatch during preparation. The thermal shock resistance of the best composite (SiC fibre/DURAN glass) does not show a significant decrease of flexural strength even after 60 shocks from 550 to 25deg C in water, while the bulk glass sample of the same dimension was destroyed by one thermal shock from 350deg C. (orig.) [de

Low stress creep behaviour of zirconium

International Nuclear Information System (INIS)

Prasad, N.

1989-01-01

Creep behaviour of alpha zirconium of grain size varying between 16 and 55 μm has been investigated in the temperature range 813 to 1003K at stresses upto 5.5 MNm -2 using high sensitive spring specimen geometry. Creep experiments on specimens of 50 μm grain size revealed a transition from lattice diffusion controlled viscous creep at temperatures greater than 940K to grain boundary diffusion controlled viscous creep at lower temperatures. Tests conducted on either side of the transition suggest the dominance of Nabarro-Herring and Coble creep processes respectively. Evidence for power-law creep has been observed in practically all the creep tests. Based on the experimental data obtained in the present study and those recently reported by Novotny et al (1985), Langdon creep mechanism maps have bee n constructed at 873 and 973K. With the help of these maps for zirconium and those published for titanium the low stress creep behaviour of zirconium and titanium are compared. (author). 22 refs., 11 figs., 3 tabs

Low temperature magnetic behaviour of glass-covered magnetic microwires with gradient nanocrystalline microstructure

Energy Technology Data Exchange (ETDEWEB)

Serrano, I. G.; Hernando, A.; Marín, P. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155 las Rozas, Madrid 28230 (Spain)

2014-01-21

Slow nanocrystallization driving dynamics can be affected by the combination of two factors: sample residual stresses and sample geometry. This effect is evidenced at the initial stages of nanocrystallization of amorphous CoFeSiBCuNb magnetic microwires. Transmission electron microscopy observations indicate how crystallization at temperatures between 730 and 780 K results in a graded microstructure where the crystallization at the surface skin of the microwire, which remains almost amorphous, differs from that of the middle, where elongated grains are observed, and inner regions. However, samples annealed at higher temperatures present a homogeneous microstructure. The effect of gradient microstructure on magnetic properties has been also analyzed and a loss of bistable magnetic behaviour at low temperatures, from that obtained in the amorphous and fully nanocrystallized sample, has been observed and ascribed to changes in sign of magnetostriction for measuring temperatures below 100 K.

Prehistory effects on the VHCF behaviour of engineering metallic materials with different strengthening mechanisms

International Nuclear Information System (INIS)

Zimmermann, M; Stoecker, C; Mueller-Bollenhagen, C; Christ, H-J

2010-01-01

Engineering materials often undergo a plastic deformation during manufacturing, hence the effect of a predeformation on the subsequent fatigue behaviour has to be considered. The effect of a prestrain on the microstructure is strongly influenced by the strengthening mechanism. Different mechanisms are relevant in the materials applied in this study: a solid-solution hardened and a precipitation-hardened nickel-base alloy and a martensite-forming metastable austenitic steel. Prehistory effects become very important, when fatigue failure at very high number of cycles (N > 10 7 ) is considered, since damage mechanisms occur different to those observed in the range of conventional fatigue limit. With the global strain amplitude being well below the static elastic limit, only inhomogeneously distributed local plastic deformation takes place in the very high cycle fatigue (VHCF) region. The dislocation motion during cyclic loading thus depends on the effective flow stress, which is defined by the global cyclic stress-strain relation and the local stress distribution as a consequence of the interaction between dislocations and precipitates, grain boundaries, martensite phases and micro-notches. As a consequence, no significant prehistory effect was observed for the VHCF behaviour of the solid-solution hardening alloy, while the precipitation-hardening alloy shows a perceptible prehistory dependence. In the case of the austenitic steel, strain-hardening and the volume fraction of the deformation-induced martensite dominate the fatigue behaviour.

Thermal stresses in hexagonal materials - heat treatment influence on their mechanical behaviour

International Nuclear Information System (INIS)

Gloaguen, D.; Freour, S.; Guillen, R.; Royer, J.; Francois, M.

2004-01-01

Internal stresses due to anisotropic thermal and plastic properties were investigated in rolled zirconium and titanium. The thermal stresses induced by a cooling process were predicted using a self-consistent model and compared with experimental results obtained by X-ray diffraction. The study of the elastoplastic response during uniaxial loading was performed along the rolling and the transverse direction of the sheet, considering the influence of the texture and the thermal stresses on the mechanical behaviour. An approach in order to determine the thermal behaviour of phases embedded in two-phase materials is also presented. For zirconium, the residual stresses due to thermal anisotropy are rather important (equivalent to 35% of the yield stress) and consequently they play an important role on the elastoplastic transition contrary to titanium. The study of two-phase material shows the influence and the interaction of the second phase on the thermal behaviour in the studied phase

A mathematical model for describing the mechanical behaviour of root canal instruments.

Science.gov (United States)

Zhang, E W; Cheung, G S P; Zheng, Y F

2011-01-01

The purpose of this study was to establish a general mathematical model for describing the mechanical behaviour of root canal instruments by combining a theoretical analytical approach with a numerical finite-element method. Mathematical formulas representing the longitudinal (taper, helical angle and pitch) and cross-sectional configurations and area, the bending and torsional inertia, the curvature of the boundary point and the (geometry of) loading condition were derived. Torsional and bending stresses and the resultant deformation were expressed mathematically as a function of these geometric parameters, modulus of elasticity of the material and the applied load. As illustrations, three brands of NiTi endodontic files of different cross-sectional configurations (ProTaper, Hero 642, and Mani NRT) were analysed under pure torsion and pure bending situation by entering the model into a finite-element analysis package (ANSYS). Numerical results confirmed that mathematical models were a feasible method to analyse the mechanical properties and predict the stress and deformation for root canal instruments during root canal preparation. Mathematical and numerical model can be a suitable way to examine mechanical behaviours as a criterion of the instrument design and to predict the stress and strain experienced by the endodontic instruments during root canal preparation. © 2010 International Endodontic Journal.

Effect of ageing time and temperature on corrosion behaviour of aluminum alloy 2014

Science.gov (United States)

Gadpale, Vikas; Banjare, Pragya N.; Manoj, Manoranjan Kumar

2018-03-01

In this paper, the effect of corrosion behaviour of aluminium alloy 2014 were studied by potentiodynamic polarization in 1 mole of NaCl solution of aged sample. The experimental testing results concluded that, corrosion resistance of Aluminum alloy 2014 degraded with the increasing the temperature (150°C & 200°C) and time of ageing. Corroded surface of the aged specimens was tested under optical microscopes for microstructures for phase analysis. Optical micrographs of corroded surfaces showed general corrosion and pitting corrosion. The corrosion resistance of lower ageing temperature and lower ageing time is higher because of its fine distribution of precipitates in matrix phase.

Statistics of energy levels and zero temperature dynamics for deterministic spin models with glassy behaviour

NARCIS (Netherlands)

Degli Esposti, M.; Giardinà, C.; Graffi, S.; Isola, S.

2001-01-01

We consider the zero-temperature dynamics for the infinite-range, non translation invariant one-dimensional spin model introduced by Marinari, Parisi and Ritort to generate glassy behaviour out of a deterministic interaction. It is argued that there can be a large number of metastable (i.e.,

Impact of annealing temperature on the mechanical and electrical properties of sputtered aluminum nitride thin films

Energy Technology Data Exchange (ETDEWEB)

Gillinger, M.; Schneider, M.; Bittner, A.; Schmid, U. [Institute of Sensor and Actuator Systems, Vienna University of Technology, Vienna 1040 (Austria); Nicolay, P. [CTR Carinthian Tech Research AG, Villach 9524 (Austria)

2015-02-14

Aluminium nitride (AlN) is a promising material for challenging sensor applications such as process monitoring in harsh environments (e.g., turbine exhaust), due to its piezoelectric properties, its high temperature stability and good thermal match to silicon. Basically, the operational temperature of piezoelectric materials is limited by the increase of the leakage current as well as by enhanced diffusion effects in the material at elevated temperatures. This work focuses on the characterization of aluminum nitride thin films after post deposition annealings up to temperatures of 1000 °C in harsh environments. For this purpose, thin film samples were temperature loaded for 2 h in pure nitrogen and oxygen gas atmospheres and characterized with respect to the film stress and the leakage current behaviour. The X-ray diffraction results show that AlN thin films are chemically stable in oxygen atmospheres for 2 h at annealing temperatures of up to 900 °C. At 1000 °C, a 100 nm thick AlN layer oxidizes completely. For nitrogen, the layer is stable up to 1000 °C. The activation energy of the samples was determined from leakage current measurements at different sample temperatures, in the range between 25 and 300 °C. Up to an annealing temperature of 700 °C, the leakage current in the thin film is dominated by Poole-Frenkel behavior, while at higher annealing temperatures, a mixture of different leakage current mechanisms is observed.

Hydro-mechanical behaviour of a heterogeneous compacted soil: experimental observations and modelling

International Nuclear Information System (INIS)

Gens, A.; Vallejan, B.; Sanchez, M.; Imbert, C.; Villar, M.V.; Van Geet, M.

2011-01-01

The paper describes a theoretical and experimental study of the coupled hydro-mechanical behaviour of a compacted mixture of bentonite powder and bentonite pellets intended as sealing material in underground repositories for nuclear waste. One of the main advantages of the use of powder/pellets mixtures is the reduction of the compaction effort required to achieve the value of average dry density necessary to attain the required swelling potential. However, the heterogeneous fabric of the material requires special approaches in order to describe adequately its behaviour during hydration. A double porosity formulation is presented to account for the presence of two distinct structural levels in the material. Hydraulic equilibrium between the two porosities is not assumed; instead a water exchange term between them is postulated. The formulation is applied to the modelling of a number of one-dimensional swelling pressure tests performed in the CEA (Commissariat a l'Energie Atomique, France) and CIEMAT (Spain) laboratories. A very satisfactory quantitative description of the experimental observations is obtained that includes a number of complex behaviour features such as size effects and non-monotonic development of swelling pressures. Some micro-fabric observations using X-ray tomography and mercury intrusion porosimetry lend support to the conceptual approach adopted. The formulation is then applied to the analysis of a long-term large-scale sealing test performed at the Hades underground facility in Belgium, using the same set of hydraulic and mechanical parameters employed in the modelling of the laboratory tests. Although the field observations exhibit a much higher degree of scatter, the basic behaviour of the field sealing test is satisfactorily simulated. A formulation that incorporates basic features of the micro-fabric of the mixture is thus able to span successfully over a large range of space and time scales. (authors)

Experimental study and modelling of high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steel weldments; Etude experimentale et modelisation, du comportement, de l'endommagement et de la rupture en fluage a haute temperature de joint soudes en acier 9Cr1Mo-NbV

Energy Technology Data Exchange (ETDEWEB)

Gaffard, V

2004-12-15

Chromium martensitic stainless steels are under development since the 70's with the prospect of using them as structural components in thermal and nuclear power plants. The modified 9Cr1Mo-NbV steel is already used, especially in England and Japan, as a material for structural components in thermal power plants where welding is a commonly used joining technique. New generations of chromium martensitic stainless steels with improved mechanical properties for high pressure and temperature use are currently under development. However, observations of several in-service premature failures of welded components in 9Cr1Mo-NbV steel, outline a strong need for understanding the high temperature creep flow and damage behaviour of 9Cr1Mo-NbV steels and weldments. The present study aimed at experimentally determining and then modelling the high temperature creep flow and damage behaviour of both 9Cr1Mo-NbV steels and weldments (typically in the temperature range from 450 C to 650 C). The base metal was first studied as the reference material. It was especially evidenced that tempered chromium martensitic steels exhibit a change in both creep flow and damage behaviour for long term creep exposure. As a consequence, the classically performed extrapolation of 1,000 hours creep data to 100,000 hours creep lifetime predictions might be very hazardous. Based on experimental observations, a new model, integrating and coupling multiple creep flow and damage mechanisms, was developed in the framework of the mechanics of porous media. It was then successfully used to represent creep flow and damage behaviour of the base metal from high to low stress levels even for complex multiaxial loading conditions. Although the high temperature creep properties of the base metal are quite good, the occurrence of premature failure in weldments in high temperature creep conditions largely focused the attention of the scientific community. The lower creep strength of the weld component was also

Effects of temperature and surface orientation on migration behaviours of helium atoms near tungsten surfaces

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaoshuang; Wu, Zhangwen; Hou, Qing, E-mail: qhou@scu.edu.cn

2015-10-15

Molecular dynamics simulations were performed to study the dependence of migration behaviours of single helium atoms near tungsten surfaces on the surface orientation and temperature. For W{100} and W{110} surfaces, He atoms can quickly escape out near the surface without accumulation even at a temperature of 400 K. The behaviours of helium atoms can be well-described by the theory of continuous diffusion of particles in a semi-infinite medium. For a W{111} surface, the situation is complex. Different types of trap mutations occur within the neighbouring region of the W{111} surface. The trap mutations hinder the escape of He atoms, resulting in their accumulation. The probability of a He atom escaping into vacuum from a trap mutation depends on the type of the trap mutation, and the occurrence probabilities of the different types of trap mutations are dependent on the temperature. This finding suggests that the escape rate of He atoms on the W{111} surface does not show a monotonic dependence on temperature. For instance, the escape rate at T = 1500 K is lower than the rate at T = 1100 K. Our results are useful for understanding the structural evolution and He release on tungsten surfaces and for designing models in other simulation methods beyond molecular dynamics.

Mechanical properties and corrosion behaviour of MIG welded 5083 aluminium alloy

Energy Technology Data Exchange (ETDEWEB)

Durmus, Huelya [Celal Bayar Univ., Turgutlu-Manisa (Turkey)

2011-07-01

For this study 5083 Aluminium alloy plates, as used in automobiles and watercraft, were experimentally MIG welded. The plates were joined with different wires and at various currents. The effects of welding with different parameters on the mechanical and corrosion properties were investigated. The corrosion behaviour of the MIG welded 5083 Aluminium base material was also investigated. The effects of the chemical composition of the filler material on the mechanical properties were examined by metallographic inspection and tensile testing. By EDS and XRD analyses of specimens it turned out that different structures in the weld metal (Cu3Si) affect its mechanical properties. The mechanical properties of the specimens welded with 5356 filler metal were found as quite well improved as compared to those specimens welded with 4043 and 5183 filler material. The results of the metallographic analysis, and mechanical and corrosion tests exhibited that the 5356 filler material was most suitable for the 5083 Al alloy base material. (orig.)

Crack resistance behaviour of an intermetallic Ti-Al-Si-Nb alloy at room temperature

International Nuclear Information System (INIS)

Wittkowsky, B.U.; Pfuff, M.J.

1996-01-01

The room temperature crack growth behaviour of a Ti-Al-Si-Nb alloy consisting of the two intermetallic phases (Ti, Nb) 3 (Al, Si) and (Ti, Nb) 5 (Si, Al) 3 is investigated in the present paper. The material exhibits a heterogeneous disordered microstructure and fails in a brittle manner. Crack growth is associated with a pronounced crack resistance behaviour. For a sample of nominally identical specimens the R-curves scatter around a mean curve with a standard deviation which remains roughly constant as the crack grows. A natural extension of the bundle model introduced in a previous paper is used to simulate R-curves and their scatter is in reasonably good agreement with the experimental findings. (orig.)

Mechanical and fracture behaviour of Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloys

International Nuclear Information System (INIS)

Dogan, B.; Schwalbe, K.H.

1990-01-01

Titanium alloys have increasingly been used in gas turbine applications due to their high strength-to-weight ratio that leads to improved engine performance and fuel efficiency. The development of required mechanical properties in titanium alloys is strongly controlled by the microstructure achieved by heat treatment and thermomechanical processing. A study is conducted on two Ti-6242-Si alloys with a lamellar and an equiaxed microstructure, to assess the effects of microstructure on the deformation and fracture behaviour based on structural observations. The observations are made on fracture surfaces and sectioned side surfaces of fractured tensile, creep, impact and fracture toughness specimens tested at test temperatures up to 500deg C, correlated with the microstructural constituents. (orig.) With 6 figs., 3 tabs [de

Structural mechanics of nuclear plant components

International Nuclear Information System (INIS)

Roche, R.

1986-10-01

Sound structural analysis are needed for designing safe and reliable components, hence his play is very important in nuclear industry. This report is a provisional writing on the good practice in structural mechanics. Emphasis is put on non elastic analysis, damage appraisal, fatigue, fracture mechanics and also on elevated temperature behaviour [fr

Post Irradiation Mechanical Behaviour of Three EUROFER Joints

International Nuclear Information System (INIS)

Lucon, E.; Leenaers, A.; Vandermeulen, W.

2006-01-01

The post-irradiation mechanical properties of three EUROFER joints (two diffusion joints and one TIG weld) have been characterized after irradiation to 1.8 dpa at 300 degrees Celsius in the BR-2 reactor. Tensile, KLST impact and fracture toughness tests have been performed. Based on the results obtained and on the comparison with data from EUROFER base material irradiated under similar conditions, the post-irradiation mechanical behaviour of both diffusion joints (laboratory and mock-up) appears similar to that of the base material. The properties of the TIG joint are affected by the lack of a post-weld heat treatment, which causes the material from the upper part of the weld to be significantly worse than that of the lower region. Thus, specimens from the upper layer exhibit extremely pronounced hardening and embrittlement caused by irradiation. The samples extracted from the lower layer show much better resistance to neutron exposure, although their measured properties do not match those of the diffusion joints. The results presented demonstrate that diffusion joining can be a very promising technique.

Study of the water retention and the consolidation of partially saturated soils in a thermo-hydro-mechanical framework

International Nuclear Information System (INIS)

Salager, Simon

2007-01-01

This work is concerned with the study of water retention and consolidation of unsaturated soils in a thermo-hydro-mechanical framework. It is organized into two parts which deal respectively with deformation and temperature effects on hydric behaviour, and suction and temperature effects on mechanical behaviour. In the first part, we point out the relevance of the characteristic surface concept for soils as opposed to the retention curve, which has limited modelling power in the case of deformable media. The characteristic surface concept is experimentally illustrated for the example of a clayey silty sand. Its modelling is based on a large sample of experimental investigations with about 240 measurements of the triplet void ratio, water content, suction. In addition, a thermo-hydric behaviour model is proposed in order to determine the characteristic surface and the retention curve for a given temperature. This model is validated for the case of two materials: a ceramic and a clayey silty sand through direct testing, and for other materials on the basis of an analysis of the literature. Finally, we present an application to the determination of the permeability of unsaturated soils taking into account deformation and temperature. In the second part, temperature and suction effects on the mechanical behaviour are studied through consolidation tests on 'Sion' silt. These tests are performed for different temperatures and suctions. For each test, swelling and compression indexes, as well as the pre-consolidation pressure are measured. The influence of temperature and suction on these essential parameters of mechanical behaviour is determined. Finally, we propose a theoretical model which account for pre-consolidation pressure as a function of temperature and suction. (author)

Mechanisms of Low-Temperature Nitridation Technology on a TaN Thin Film Resistor for Temperature Sensor Applications.

Science.gov (United States)

Chen, Huey-Ru; Chen, Ying-Chung; Chang, Ting-Chang; Chang, Kuan-Chang; Tsai, Tsung-Ming; Chu, Tian-Jian; Shih, Chih-Cheng; Chuang, Nai-Chuan; Wang, Kao-Yuan

2016-12-01

In this letter, we propose a novel low-temperature nitridation technology on a tantalum nitride (TaN) thin film resistor (TFR) through supercritical carbon dioxide (SCCO2) treatment for temperature sensor applications. We also found that the sensitivity of temperature of the TaN TFR was improved about 10.2 %, which can be demonstrated from measurement of temperature coefficient of resistance (TCR). In order to understand the mechanism of SCCO2 nitridation on the TaN TFR, the carrier conduction mechanism of the device was analyzed through current fitting. The current conduction mechanism of the TaN TFR changes from hopping to a Schottky emission after the low-temperature SCCO2 nitridation treatment. A model of vacancy passivation in TaN grains with nitrogen and by SCCO2 nitridation treatment is eventually proposed to increase the isolation ability in TaN TFR, which causes the transfer of current conduction mechanisms.

High-temperature strength of AISI 316 steel

International Nuclear Information System (INIS)

Antunes, A.E.B.; Monteiro, S.N.

1975-01-01

The mechanical properties, especially elastic limit and strain hardening of AISI-316 austenitic stainless steel were investigated within the temperature range 150-800 0 C for two strain rates. The results showed anomalous behaviour between 200 and 650 0 C, over which range there was an increase in maximum strenght and hardening, with a tendency to show peaks. These apparentley three in number, may be connected with the effects of interaction between point defects and dislocations leading to dinamic aging phenomena. The mechanisms responsible for this anomalous behaviour produce a negative dependence on strain rate [pt

Non-monotonic behaviour in relaxation dynamics of image restoration

International Nuclear Information System (INIS)

Ozeki, Tomoko; Okada, Masato

2003-01-01

We have investigated the relaxation dynamics of image restoration through a Bayesian approach. The relaxation dynamics is much faster at zero temperature than at the Nishimori temperature where the pixel-wise error rate is minimized in equilibrium. At low temperature, we observed non-monotonic development of the overlap. We suggest that the optimal performance is realized through premature termination in the relaxation processes in the case of the infinite-range model. We also performed Markov chain Monte Carlo simulations to clarify the underlying mechanism of non-trivial behaviour at low temperature by checking the local field distributions of each pixel

Flow behaviour of autoclaved, 20% cold worked, Zr-2.5Nb alloy pressure tube material in the temperature range of room temperature to 800 deg. C

International Nuclear Information System (INIS)

Dureja, A.K.; Sinha, S.K.; Srivastava, Ankit; Sinha, R.K.; Chakravartty, J.K.; Seshu, P.; Pawaskar, D.N.

2011-01-01

Pressure tube material of Indian Heavy Water Reactors is 20% cold-worked and stress relieved Zr-2.5Nb alloy. Inherent variability in the process parameters during the fabrication stages of pressure tube and also along the length of component have their effect on micro-structural and texture properties of the material, which in turn affect its strength parameters (yield strength and ultimate tensile strength) and flow characteristics. Data of tensile tests carried out in the temperature range from room temperature to 800 deg. C using the samples taken out from a single pressure tube have been used to develop correlations for characterizing the strength parameters' variation as a function of axial location along length of the tube and the test temperature. Applicability of Ramberg-Osgood, Holloman and Voce's correlations for defining the post yield behaviour of the material has been investigated. Effect of strain rate change on the deformation behaviour has also been studied.

Mechanical behaviour and failure of fuel cladding zirconium alloys in nuclear power plants under accidental RIA-type situation

International Nuclear Information System (INIS)

Doan, D.T.

2009-01-01

In French Nuclear Pressurized Water Reactors (PWRs), most of structural parts of the fuel assembly consist of zirconium alloy tubes and plates. Optimizing the management of fuel in nuclear power plants led to the increase in the duration of fuel cycles and power. The use of high fuel burnups requires drastic changes in the rules for reactor design in the nuclear safety. The evaluation of nuclear reactors in accident situations is based on reference accident scenarios. One of these hypothetical accidents, examined in this study, is the 'Reactivity Initiated Accident'. In order to assess the structural integrity of these parts it is necessary to characterize both the plastic flow and fracture behaviour of the materials at various stages of the life cycle, (i.e. at increasing levels of hydriding, irradiation, oxidation or thermal mechanical loading). The purpose of this work is to provide experimental data and to develop a model of the thermo-mechanical behaviour and to propose a design analysis method in the case of non-irradiated clads, in RIA-type situations. Mechanical tests were conducted on Cold-Worked-Stress-Relieved and on Recrystallized Zircaloy-4 sheets using various kinds of samples including smooth and notched tensile specimens and small punch tests. Temperature was set to 25, 250 and 600 C with hydrogen contents between 0 and 1000 ppm. The model is based on a simplified description of a Zircaloy polycrystal in which scalar isotropic ductile damage including void nucleation and growth is added. The model is also physically based to easily transfer parameters determined for one material state to another (e.g. transfer between sheet and tube or between different levels of irradiation). The model was implemented in the Finite Element software Zebulon using either an explicit or an implicit time integration scheme. Uniaxial tension tests were used to tune the model parameters for both materials, considering various values of temperature and hydrogen levels

Changing micronutrient intake through (voluntary) behaviour change

DEFF Research Database (Denmark)

Jensen, Birger Boutrup; Lähteenmäki, Liisa; Grunert, Klaus G

2012-01-01

change. The behaviours affecting folate intake were recognised and categorised. Behaviour change mechanisms from “rational model of man”, behavioural economics, health psychology and social psychology were identified and aligned against folate-related behaviours. The folate example demonstrated......The objective of this study was to relate behaviour change mechanisms to nutritionally relevant behaviour and demonstrate how the different mechanisms can affect attempts to change these behaviours. Folate was used as an example to illuminate the possibilities and challenges in inducing behaviour...... the complexity of mechanisms influencing possible behavioural changes, even though this only targets the intake of a single micronutrient. When considering possible options to promote folate intake, the feasibility of producing the desired outcome should be related to the mechanisms of required changes...

Influence of tempering temperature on mechanical properties of cast steels

Directory of Open Access Journals (Sweden)

G. Golański

2008-12-01

Full Text Available The paper presents results of research on the influence of tempering temperature on structure and mechanical properties of bainite hardened cast steel: G21CrMoV4 – 6 (L21HMF and G17CrMoV5 – 10 (L17HMF. Investigated cast steels were taken out from internal frames of steam turbines serviced for long time at elevated temperatures. Tempering of the investigated cast steel was carried out within the temperature range of 690 ÷ 730 C (G21CrMoV4 – 6 and 700 ÷ 740 C (G17CrMoV5 – 10. After tempering the cast steels were characterized by a structure of tempered lower bainite with numerous precipitations of carbides. Performed research of mechanical properties has shown that high temperatures of tempering of bainitic structure do not cause decrease of mechanical properties beneath the required minimum.oo It has also been proved that high-temperature tempering (>720 oC ensures high impact energy at the 20% decrease of mechanical properties.

Molecular Mechanisms Regulating Temperature Compensation of the Circadian Clock.

Science.gov (United States)

Narasimamurthy, Rajesh; Virshup, David M

2017-01-01

An approximately 24-h biological timekeeping mechanism called the circadian clock is present in virtually all light-sensitive organisms from cyanobacteria to humans. The clock system regulates our sleep-wake cycle, feeding-fasting, hormonal secretion, body temperature, and many other physiological functions. Signals from the master circadian oscillator entrain peripheral clocks using a variety of neural and hormonal signals. Even centrally controlled internal temperature fluctuations can entrain the peripheral circadian clocks. But, unlike other chemical reactions, the output of the clock system remains nearly constant with fluctuations in ambient temperature, a phenomenon known as temperature compensation. In this brief review, we focus on recent advances in our understanding of the posttranslational modifications, especially a phosphoswitch mechanism controlling the stability of PER2 and its implications for the regulation of temperature compensation.

Molecular Mechanisms Regulating Temperature Compensation of the Circadian Clock

Directory of Open Access Journals (Sweden)

David M. Virshup

2017-04-01

Full Text Available An approximately 24-h biological timekeeping mechanism called the circadian clock is present in virtually all light-sensitive organisms from cyanobacteria to humans. The clock system regulates our sleep–wake cycle, feeding–fasting, hormonal secretion, body temperature, and many other physiological functions. Signals from the master circadian oscillator entrain peripheral clocks using a variety of neural and hormonal signals. Even centrally controlled internal temperature fluctuations can entrain the peripheral circadian clocks. But, unlike other chemical reactions, the output of the clock system remains nearly constant with fluctuations in ambient temperature, a phenomenon known as temperature compensation. In this brief review, we focus on recent advances in our understanding of the posttranslational modifications, especially a phosphoswitch mechanism controlling the stability of PER2 and its implications for the regulation of temperature compensation.

High temperature mechanical properties of iron aluminides

International Nuclear Information System (INIS)

Morris, D. G.; Munoz-Morris, M. A.

2001-01-01

Considerable attention has been given to the iron aluminide family of intermetallics over the past years since they offer considerable potential as engineering materials for intermediate to high temperature applications, particularly in cases where extreme oxidation or corrosion resistance is required. Despite efforts at alloy development, however, high temperature strength remains low and creep resistance poor. Reasons for the poor high-temperature strength of iron aluminides will be discussed, based on the ordered crystal structure, the dislocation structure found in the materials, and the mechanisms of dislocation pinning operating. Alternative ways of improving high temperature strength by microstructural modification and the inclusion of second phase particles will also be considered. (Author)

Mechanisms of change in human behaviour

OpenAIRE

Marchal, Paul; Bartelings, Heleen; Bastardie, François; Batsleer, Jurgen; Delaney, Alyne; Girardin, Raphael; Gloaguen, Pierre; Hamon, Katell; Hoefnagel, Ellen; Jouanneau, Charlène; Mahevas, Stephanie; Nielsen, Rasmus; Piwowarczyk, Joanna; Poos, Jan-jaap; Schulze, Torsten

2014-01-01

The scope of this report is to present the science developed within the VECTORS project to improve the understanding of the key processes driving the behaviour of human agents utilising a variety of EU maritime domains. While particular attention has been paid to the spatial interactions between fishing activities and other human uses (e.g., maritime traffic, offshore wind parks, aggregate extractions), the behaviour of non-fishing sectors of activity has also been considered. Various quantit...

Experimental investigation of the behaviour of tungsten and molybdenum alloys at high strain-rate and temperature

CERN Document Server

Scapin, Martina; Carra, Federico; Peroni, Lorenzo

2015-01-01

The introduction in recent years of new, extremely energetic particle accelerators such as the Large Hadron Collider (LHC) gives impulse to the development and testing of refractory metals and alloys based on molybdenum and tungsten to be used as structural materials. In this perspective, in this work the experimental results of a tests campaign on Inermet® IT180 and pure Molybdenum (sintered by two different producers) are presented. The investigation of the mechanical behaviour was performed in tension varying the strain-rates, the temperatures and both of them. Overall six orders of magnitude in strain-rate (between 10−3 and 103 s−1) were covered, starting from quasi-static up to high dynamic loading conditions. The high strain-rate tests were performed using a direct Hopkinson Bar setup. Both in quasi-static and high strain-rate conditions, the heating of the specimens was obtained with an induction coil system, controlled in feedback loop, based on measurements from thermocouples directly welded on...

The effects of the finest grains on the mechanical behaviours of nanocrystalline materials

International Nuclear Information System (INIS)

Hu Lingling; Huo Ruxiao; Zhou Jianqiu; Wang Ying; Zhang Shu

2012-01-01

This article proposes a new constitutive model to account for effects of the finest grains, with sizes ranging from 2 to 4 nm, on the mechanical behaviours of nanocrystalline (NC) materials. In this model, the normal nanograins (ranging from 20 to 100 nm) were treated as though they were composed of a grain interior (GI) and a grain boundary (GB) affected zone (GBAZ). The finest grains were considered to be part of the GBAZ, denoted as super triple junctions (STJs). For the initial plastic deformation stage of the NC materials, a phenomenological constitutive equation was suggested to predict the deformation behaviours of the GBAZ. The formation of GB dislocation (GBD) pileups provides dramatic strain hardening in deformed NC materials and thereby enhances their ductility. Then, the constitutive equations to describe the plastic deformation of the GI and the GBAZ lattice region were established. In this stage, the GBAZ are already saturated with GBD pileups, and GI deformation is the dominant mechanism. Finally, the mechanical model for the NC materials with the finest grains was built using the self-consistent method, and an overall moderate “work hardening,” sustained over a long range of plastic strain, was predicted. The effects of TJs/STJs on the deformation mechanism were quantitatively analysed. The analysis demonstrated that the existence of the finest grains will simultaneously lead to good strength and good ductility.

Too Hot to Sleep? Sleep Behaviour and Surface Body Temperature of Wahlberg’s Epauletted Fruit Bat

Science.gov (United States)

Downs, Colleen T.; Awuah, Adwoa; Jordaan, Maryna; Magagula, Londiwe; Mkhize, Truth; Paine, Christine; Raymond-Bourret, Esmaella; Hart, Lorinda A.

2015-01-01

The significance of sleep and factors that affect it have been well documented, however, in light of global climate change the effect of temperature on sleep patterns has only recently gained attention. Unlike many mammals, bats (order: Chiroptera) are nocturnal and little is known about their sleep and the effects of ambient temperature (Ta) on their sleep. Consequently we investigated seasonal temperature effects on sleep behaviour and surface body temperature of free-ranging Wahlberg’s epauletted fruit bat, Epomophorus wahlbergi, at a tree roost. Sleep behaviours of E. wahlbergi were recorded, including: sleep duration and sleep incidences (i.e. one eye open and both eyes closed). Sleep differed significantly across all the individuals in terms of sleep duration and sleep incidences. Individuals generally spent more time awake than sleeping. The percentage of each day bats spent asleep was significantly higher during winter (27.6%), compared with summer (15.6%). In summer, 20.7% of the sleeping bats used one eye open sleep, and this is possibly the first evidence of one-eye-sleep in non-marine mammals. Sleep duration decreased with extreme heat as bats spent significantly more time trying to cool by licking their fur, spreading their wings and panting. Skin temperatures of E. wahlbergi were significantly higher when Ta was ≥35°C and no bats slept at these high temperatures. Consequently extremely hot days negatively impact roosting fruit bats, as they were forced to be awake to cool themselves. This has implications for these bats given predicted climate change scenarios. PMID:25775371

Temperature Dependence of Mechanical Properties of TRISO SiC Coatings

International Nuclear Information System (INIS)

Kim, Do Kyung; Park, Kwi Il; Lee, Hyeon Keun; Seong, Young Hoon; Lee, Seung Jun

2009-04-01

SiC coating layer has been introduced as protective layer in TRISO nuclear fuel particle of high temperature gas cooled reactor (HTGR) due to excellent mechanical stability at high temperature. It is important to study for high temperature stability in SiC coating layers, because TRISO fuel particles were operating at high temperature around 1000 .deg. C. In this study, the nanoindentation test and micro tensile test were conducted in order to measure the mechanical properties of SiC coating layers at elevated temperature. SiC coating film was fabricated on the carbon substrate using chemical vapor deposition process with different microstructures and thicknesses. Nanoindentation test was performed for the analysis of the hardness, modulus and creep properties up to 500 .deg. C. Impression creep method applied to nanoindentation and creep properties of SiC coating layers were characterized by nanoindentation creep test. The fracture strength of SiC coating layers was measured by the micro tensile method at room temperature and 500 .deg. C. From the results, we can conclude that the hardness and fracture strength are decreased with temperature and no significant change in the modulus is observed with increase in temperature. The deformation mechanism for indentation creep and creep rate changes as the testing temperature increased

Coupling between mechanical behaviour and drying of cementing materials: experimental study on mortars

International Nuclear Information System (INIS)

Yurtdas, I.

2003-10-01

The aim of this work is to understand the desiccation effects on the mechanical behaviour of cement materials. Two mortars of ratio E/C=0.5 and 0.8 have been tested. All the tests have been implemented after a six months maturing in water. The experimental study has been carried out as follows: 1)tests characterizing the differed behaviour and the transport properties have been carried out 2)tests characterizing the short term multiaxial mechanical behaviour have been carried out. The desiccation shrinkage in terms of the weight loss presents three characteristic phases. The permeability measurement on the mortar 05 shows that the permeability of the specimens dried and crept is greater than those of the specimens dried before being crept, and the permeability of the specimens submitted to a desiccation creep and then dried is sensibly the same as the last one in spite of a very important differed deformation. The influence of the desiccation on the uniaxial and deviatoric compressions resistance depends of the binding agent: for a cement paste of good quality (E/C=0.5), the resistances increase with the desiccation because of the capillary depression and of the hydric gradients. For a cement paste of low quality (E/C=0.8), there is a competitive effect between the increase of the microcracks induced and the specimen rigidification; the microcracking becomes then the parameter controlling the rupture process. The elasto-plastic behaviour becomes a damageable elasto-plastic behaviour during desiccation which induces, as the decrease of the E/C ratio, a translation of the elastic limit surfaces and ruptures towards higher stresses. In parallel, the elastic properties and the incompressibility modulus are damaged and the volume deformations increase after the drying. At last, the decrease of the Young modulus and the passage to the third shrinkage phase in terms of the weight loss coincide. This can be attributed to the induced microcracking: this decrease of the

Behaviour and damage of aged austenitic-ferritic steels: a micro-mechanical approach

International Nuclear Information System (INIS)

Bugat, St.

2000-12-01

The austenitic-ferritic steels are used in the PWR primary cooling system. At the running temperature (320 C), they are submitted to a slow aging, which leads to the embrittlement of the ferritic phase. This embrittlement leads to a decrease of the mechanical properties, in particular of the crack resistance of the austenitic-ferritic steels. The damage and rupture of the austenitic-ferritic steels have been approached at the ENSMP by the works of P. Joly (1992) and of L. Devilliers-Guerville (1998). These works have allowed to reveal a damage heterogeneity which induces a strong dispersion on the ductilities and the toughnesses as well as on the scale effects. Modeling including the damage growth kinetics measured experimentally, have allowed to verify these effects. Nevertheless, they do not consider the two-phase character of the material and do not include a physical model of the cleavage cracks growth which appear in the embrittled ferrite. In this study, is proposed a description of the material allowing to treat these aspects while authorizing the structure calculation. In a first part, the material is studied. The use of the ESBD allows to specify the complex morphology of these steels and crystal orientation relations between the two phases. Moreover, it is shown that the two phases keep the same crystal orientation in the zones, called bicrystals, whose size varies between 500 μm and 1 mm. The study of the sliding lines, coupled to the ESBD, allows to specify too the deformation modes of the two phases. At last, tensile and tensile-compression tests at various deformation range are carried out to characterize the macroscopic mechanical behaviour of these materials. Then, a micro-mechanical modeling of the material behaviour is proposed. This one takes into account the three scales identified at the preceding chapter. The first scale, corresponding to the laths is described as a monocrystal whose behaviour includes both an isotropic and a kinematic strain

Principal physical mechanisms of material creep resistance and rupture at elevated temperatures

International Nuclear Information System (INIS)

Krishtal, M.A.

1977-01-01

Mechanisms of creep and long-term failure of refractory materials at different temperatures and stress levels are considered. At high temperatures and low stresses the diffusion (vacancial) mechanism is observed. Temperatures being low and stresses sufficiently high, dislocation mechanism involving avalanche dislocation break-off is manifested. Intermediate conditions provide other mechanisms, i.e. dislocation glide, dislocation climbing, grain-boundary and sub-grain-boundary mechanisms. Quantitative relationships between creep rate and some structural and kinetic parameters are discussed. Account of the creep mechanism is necessary when selecting methods for strengthening of alloys

Health Behaviours As a Mechanism in the Prospective Relation between Workplace Reciprocity and Absenteeism: A Bridge too Far ?

Directory of Open Access Journals (Sweden)

Bart De Clercq

Full Text Available The persistent lack of evidence on causal mechanisms between social capital and health threatens the credibility of the social capital-health association. The present study aims to address this ongoing problem by investigating whether health behaviours (i.e. smoking, alcohol consumption, and physical activity mediate the prospective relation between workplace reciprocity and future sickness absence.A cohort of 24,402 Belgian employees was followed up during 12 months for sickness absence. Workplace reciprocity was measured with four indicators-colleague help, colleague interest, supervisor help, and supervisor concern. Three types of multilevel mediation models were applied.Overall, workplace reciprocity negatively related to high sickness absence (≥ 10 days mainly independently from health behaviours. Uniquely, colleague interest positively related to smoking (OR = 1.058, 95% CI = 1.019, 1.098 and smoking in turn, positively related to sickness absence (OR = 1.074, 95% CI = 1.047, 1.101. No behavioural pathways could be identified between company-level reciprocity and sickness absence, and company-level health-related behaviours did not mediate the relation between company-level reciprocity and individual sickness absence.These results suggest that both social capital and health behaviours are relevant for employee health, but health behaviours seem not to be the underlying explanatory mechanism between workplace reciprocity and health.

Health Behaviours As a Mechanism in the Prospective Relation between Workplace Reciprocity and Absenteeism: A Bridge too Far ?

Science.gov (United States)

De Clercq, Bart; Clays, Els; Janssens, Heidi; De Bacquer, Dirk; Casini, Annalisa; Kittel, France; Braeckman, Lutgart

2015-01-01

The persistent lack of evidence on causal mechanisms between social capital and health threatens the credibility of the social capital-health association. The present study aims to address this ongoing problem by investigating whether health behaviours (i.e. smoking, alcohol consumption, and physical activity) mediate the prospective relation between workplace reciprocity and future sickness absence. A cohort of 24,402 Belgian employees was followed up during 12 months for sickness absence. Workplace reciprocity was measured with four indicators-colleague help, colleague interest, supervisor help, and supervisor concern. Three types of multilevel mediation models were applied. Overall, workplace reciprocity negatively related to high sickness absence (≥ 10 days) mainly independently from health behaviours. Uniquely, colleague interest positively related to smoking (OR = 1.058, 95% CI = 1.019, 1.098) and smoking in turn, positively related to sickness absence (OR = 1.074, 95% CI = 1.047, 1.101). No behavioural pathways could be identified between company-level reciprocity and sickness absence, and company-level health-related behaviours did not mediate the relation between company-level reciprocity and individual sickness absence. These results suggest that both social capital and health behaviours are relevant for employee health, but health behaviours seem not to be the underlying explanatory mechanism between workplace reciprocity and health.

Mechanical Behaviour of Soil Improved by Alkali Activated Binders

Directory of Open Access Journals (Sweden)

Enza Vitale

2017-11-01

Full Text Available The use of alkali activated binders to improve engineering properties of clayey soils is a novel solution, and an alternative to the widely diffused improvement based on the use of traditional binders such as lime and cement. In the paper the alkaline activation of two fly ashes, by-products of coal combustion thermoelectric power plants, has been presented. These alkali activated binders have been mixed with a clayey soil for evaluating the improvement of its mechanical behaviour. One-dimensional compression tests on raw and treated samples have been performed with reference to the effects induced by type of binder, binder contents and curing time. The experimental evidences at volume scale of the treated samples have been directly linked to the chemo-physical evolution of the binders, investigated over curing time by means of X Ray Diffraction. Test results showed a high reactivity of the alkali activated binders promoting the formation of new mineralogical phases responsible for the mechanical improvement of treated soil. The efficiency of alkali activated binders soil treatment has been highlighted by comparison with mechanical performance induced by Portland cement.

Effect of mechanical behaviour of the brachial artery on blood pressure measurement during both cuff inflation and cuff deflation.

Science.gov (United States)

Zheng, Dingchang; Pan, Fan; Murray, Alan

2013-10-01

The aim of this study was to investigate the effect of different mechanical behaviour of the brachial artery on blood pressure (BP) measurements during cuff inflation and deflation. BP measurements were taken from each of 40 participants, with three repeat sessions under three randomized cuff deflation/inflation conditions. Cuff pressure was linearly deflated and inflated at a standard rate of 2-3 mmHg/s and also linearly inflated at a fast rate of 5-6 mmHg/s. Manual auscultatory systolic and diastolic BPs, and pulse pressure (SBP, DBP, PP) were measured. Automated BPs were determined from digitally recorded cuff pressures by fitting a polynomial model to the oscillometric pulse amplitudes. The BPs from cuff deflation and inflation were then compared. Repeatable measurements between sessions and between the sequential order of inflation/deflation conditions (all P > 0.1) indicated stability of arterial mechanical behaviour with repeat measurements. Comparing BPs obtained by standard inflation with those from standard deflation, manual SBP was 2.6 mmHg lower (P deflation suggest different arterial mechanical behaviour between arterial opening and closing during BP measurement. We have shown that the mechanical behaviour of the brachial artery during BP measurement differs between cuff deflation and cuff inflation.

Behaviors of SiC fibers at high temperature

International Nuclear Information System (INIS)

Colin, C.; Falanga, V.; Gelebart, L.

2010-01-01

On the one hand, considering the improvements of mechanical and thermal behaviours of the last generation of SiC fibers (Hi-Nicalon S, Tyranno SA3); on the other hand, regarding physical and chemical properties and stability under irradiation, SiC/SiC composites are potential candidates for nuclear applications in advanced fission and fusion reactors. CEA must characterize and optimize these composites before their uses in reactors. In order to study this material, CEA is developing a multi-scale approach by modelling from fibers to bulk composite specimen: fibres behaviours must be well known in first. Thus, CEA developed a specific tensile test device on single fibers at high temperature, named MecaSiC. Using this device, we have already characterized the thermoelastic and thermoelectric behaviours of SiC fibers. Additional results about the plastic properties at high temperatures were also obtained. Indeed, we performed tensile tests between 1200 degrees C up to 1700 degrees C to characterize this plastic behaviour. Some thermal annealing, up to 3 hours at 1700 degrees C, had been also performed. Furthermore, we compare the mechanical behaviours with the thermal evolution of the electric resistivity of these SiC fibers. Soon, MecaSiC will be coupled to a new charged particle accelerator. Thus, in this configuration, we will be able to study in-situ irradiation effects on fibre behaviours, as swelling or creep for example

Mechanical degradation temperature of waste storage materials

International Nuclear Information System (INIS)

Fink, M.C.; Meyer, M.L.

1993-01-01

Heat loading analysis of the Solid Waste Disposal Facility (SWDF) waste storage configurations show the containers may exceed 90 degrees C without any radioactive decay heat contribution. Contamination containment is primarily controlled in TRU waste packaging by using multiple bag layers of polyvinyl chloride and polyethylene. Since literature values indicate that these thermoplastic materials can begin mechanical degradation at 66 degrees C, there was concern that the containment layers could be breached by heating. To better define the mechanical degradation temperature limits for the materials, a series of heating tests were conducted over a fifteen and thirty minute time interval. Samples of a low-density polyethylene (LDPE) bag, a high-density polyethylene (HDPE) high efficiency particulate air filter (HEPA) container, PVC bag and sealing tape were heated in a convection oven to temperatures ranging from 90 to 185 degrees C. The following temperature limits are recommended for each of the tested materials: (1) low-density polyethylene -- 110 degrees C; (2) polyvinyl chloride -- 130 degrees C; (3) high-density polyethylene -- 140 degrees C; (4) sealing tape -- 140 degrees C. Testing with LDPE and PVC at temperatures ranging from 110 to 130 degrees C for 60 and 120 minutes also showed no observable differences between the samples exposed at 15 and 30 minute intervals. Although these observed temperature limits differ from the literature values, the trend of HDPE having a higher temperature than LDPE is consistent with the reference literature. Experimental observations indicate that the HDPE softens at elevated temperatures, but will retain its shape upon cooling. In SWDF storage practices, this might indicate some distortion of the waste container, but catastrophic failure of the liner due to elevated temperatures (<185 degrees C) is not anticipated

Influence of Temperature on Mechanical Properties of Jute/Biopolymer Composites

DEFF Research Database (Denmark)

Løvdal, Alexandra Liv Vest; Laursen, Louise Løcke; Løgstrup Andersen, Tom

2013-01-01

Biopolymers and natural fibers are receiving wide attention for the potential to have good performance composites with low environmental impact. A current limitation of most biopolymers is however their change in mechanical properties at elevated temperatures. This study investigates the mechanical...... of the fibers. Altogether, the results demonstrate that the thermal sensitivity parameters typically provided for polymers, e.g., the glass transition temperature and the heat deflection temperature, cannot be used as sole parameters for determining the gradual change in mechanical properties of polymers...... properties of two biomass-based polymers, polylactic acid (PLA) and cellulose acetate (CA), as a function of ambient temperature in the range from 5 to 80C. Tests were done for neat polymers and for jute fiber/biopolymer composites. Micromechanical models were applied to back-calculate the reinforcement...

Fatigue behaviour of coke drum materials under thermal-mechanical cyclic loading

Directory of Open Access Journals (Sweden)

Jie Chen

2014-01-01

Full Text Available Coke drums are vertical pressure vessels used in the delayed coking process in petroleum refineries. Significant temperature variation during the delayed coking process causes damage in coke drums in the form of bulging and cracking. There were some studies on the fatigue life estimation for the coke drums, but most of them were based on strain-fatigue life curves at constant temperatures, which do not consider simultaneous cyclic temperature and mechanical loading conditions. In this study, a fatigue testing system is successfully developed to allow performing thermal-mechanical fatigue (TMF test similar to the coke drum loading condition. Two commonly used base and one clad materials of coke drums are then experimentally investigated. In addition, a comparative study between isothermal and TMF lives of these materials is conducted. The experimental findings lead to better understanding of the damage mechanisms occurring in coke drums and more accurate prediction of fatigue life of coke drum materials.

New diffusion mechanism for high temperature diffusion in solids

International Nuclear Information System (INIS)

Doan, N.V.; Adda, Y.

1986-09-01

A new atomic transport mechanism in solids at high temperatures has been discovered by Molecular Dynamics computer simulation. It can be described as a ring sequence of atomic replacements induced by unstable Frenkel pairs. This transport process takes place without stable defects, the atomic migration occurring indeed by simultaneous creation and migration of unstable defects. Starting from the analysis of this mechanism in different solids at high temperature (CaF 2 , Na, Ar) and in irradiated copper by subthreshold collisions, we discuss the role of this mechanism on various diffusion controlled phenomena and also on the atomic processes of defect creation

Modelling the behaviour of 210Po in high temperature processes

International Nuclear Information System (INIS)

Mora, J.C.; Robles, B.; Corbacho, J.A.; Gasco, Catalina; Gazquez, M.J.

2011-01-01

In several Naturally Occurring Radioactive Material (NORM) industries, relatively high temperatures are used as part of their industrial processes. In coal combustion, as occur in other high temperature processes, an increase of the activity concentration of every natural radioisotope is produced both, in residues and by-products. An additional increase can be observed in the activity concentration of radionuclides of elements with low boiling point. This work is centred in the increase of polonium, more precisely in its radioisotope Po-210, present in the natural chains, and with a half-life long enough to be considered for radiation protection purposes. This additional increase appears mainly in the residual particles that are suspended in the flue gases: the fly-ashes. Besides, scales, with a high concentration of this radioisotope, were observed. These scales are produced on surfaces with a temperature lower than the boiling point of the chemical element. Both, the accumulation in particles and the production of scales are attributed to condensation effects. When effective doses for the public and the workers are evaluated, taking into account these increases in activity concentrations, the use of theoretical models is necessary. In this work a theoretical description of those effects is presented. Moreover, a verification of the predictions of the model was performed by comparing them with measurements carried on in coal-fired power plants. The same description here presented is applicable in general to the behaviour of Po-210 in other NORM industries where high temperature processes involving raw materials are used, as can be ceramic, cement production, tiles production or steel processing.

Mechanical Resonators for Quantum Optomechanics Experiments at Room Temperature.

Science.gov (United States)

Norte, R A; Moura, J P; Gröblacher, S

2016-04-08

All quantum optomechanics experiments to date operate at cryogenic temperatures, imposing severe technical challenges and fundamental constraints. Here, we present a novel design of on-chip mechanical resonators which exhibit fundamental modes with frequencies f and mechanical quality factors Q_{m} sufficient to enter the optomechanical quantum regime at room temperature. We overcome previous limitations by designing ultrathin, high-stress silicon nitride (Si_{3}N_{4}) membranes, with tensile stress in the resonators' clamps close to the ultimate yield strength of the material. By patterning a photonic crystal on the SiN membranes, we observe reflectivities greater than 99%. These on-chip resonators have remarkably low mechanical dissipation, with Q_{m}∼10^{8}, while at the same time exhibiting large reflectivities. This makes them a unique platform for experiments towards the observation of massive quantum behavior at room temperature.

Wear Resistance and Mechanical Behaviour of Epoxy/Mollusk Shell Biocomposites developed for Structural Applications

Directory of Open Access Journals (Sweden)

I.O. Oladele

2016-09-01

Full Text Available Epoxy resin is one of the strongest commercially exploitable thermosetting polymers in the polymer family; however its expensive nature in comparison with other thermosetting polymers such as vinylester and polyester limits its applications as a structural material. Inexpensive fillers on the other hand, especially those derived from agro-industrial wastes are very important in reducing the overall cost of polymer composites and furthermore influential in enhancing some of their engineering properties. In the present study, the wear resistance and mechanical behaviour of epoxy polymer matrix filled with <75 and 75 μm calcined particles of African land snail shells have been comparatively investigated. The wear resistance and the mechanical behaviour of the composites were studied via Taber Abraser and INSTRON universal testing machine. Also, the elemental constituents of the calcined snail shell and the epoxy biocomposites were characterized by X-Ray Fluorescence Spectroscopy and Scanning Electron Microscopy/Energy Dispersion Spectroscopy. From the experimental results, it was observed that, at the highest filler loading, smaller particle size presented a biocomposite with significant enhancement in wear and mechanical properties. However, it was also observed that increase in particle size showed no significant enhancement in the mechanical properties of the biocomposites.

On the Evaluation of the Mechanical Behaviour of Structural Glass Elements

OpenAIRE

Costa, S.; Miranda, M.; Varum, H.; Teixeira-Dias, F.

2005-01-01

Glass can be considered to be a high-technology engineering material with a multifunctional potential for structural applications. However, the conventional approach to the use of glass is often based only on its proper-ties of transparency and isolation. It is thus highly appropriate and necessary to study the mechanical behaviour of this material and to develop adequate methods and models leading to its characterisation. It is evident that the great potential of growth for structural glass ...

Microstructural Evolution and Mechanical Behavior of High Temperature Solders: Effects of High Temperature Aging

Science.gov (United States)

Hasnine, M.; Tolla, B.; Vahora, N.

2018-04-01

This paper explores the effects of aging on the mechanical behavior, microstructure evolution and IMC formation on different surface finishes of two high temperature solders, Sn-5 wt.% Ag and Sn-5 wt.% Sb. High temperature aging showed significant degradation of Sn-5 wt.% Ag solder hardness (34%) while aging has little effect on Sn-5 wt.% Sb solder. Sn-5 wt.% Ag experienced rapid grain growth as well as the coarsening of particles during aging. Sn-5 wt.% Sb showed a stable microstructure due to solid solution strengthening and the stable nature of SnSb precipitates. The increase of intermetallic compound (IMC) thickness during aging follows a parabolic relationship with time. Regression analysis (time exponent, n) indicated that IMC growth kinetics is controlled by a diffusion mechanism. The results have important implications in the selection of high temperature solders used in high temperature applications.

Posttranscriptional mechanisms controlling diurnal gene expression cycles by body temperature rhythms.

Science.gov (United States)

Gotic, Ivana; Schibler, Ueli

2017-10-03

In mammals, body temperature oscillates in a daily fashion around a set point of 36°C-37°C. These fluctuations are controlled by the circadian master clock residing in the brain's suprachiasmatic nucleus and, despite their small amplitudes, contribute to the diurnal expression of genes throughout the organism. By focusing on the mechanisms underlying the temperature-dependent accumulation of the cold-inducible RNA-binding protein CIRBP - a factor involved in the tuning of amplitude and phase in circadian clocks of peripheral tissues - we have recently identified a novel mechanism governing temperature-dependent gene expression. This mechanism involves the differential spicing efficiency of primary RNA transcripts under different temperature conditions and thereby determines the fraction of Cirbp pre-mRNA processed into mature mRNA. A genome-wide transcriptome analysis revealed that this mechanism affects the output of hundreds of genes. Here we discuss our findings and future directions toward the identification of specific factors and parameters governing temperature-sensitive splicing efficacy.

Urban surface temperature behaviour and heat island effect in a tropical planned city

Science.gov (United States)

Ahmed, Adeb Qaid; Ossen, Dilshan Remaz; Jamei, Elmira; Manaf, Norhashima Abd; Said, Ismail; Ahmad, Mohd Hamdan

2015-02-01

Putrajaya is a model city planned with concepts of a "city in the garden" and an "intelligent city" in the tropics. This study presents the behaviour of the surface temperature and the heat island effect of Putrajaya. Findings show that heat island intensity is 2 °C on average at nighttime and negligible at daytime. But high surface temperature values were recorded at the main boulevard due to direct solar radiation incident, street orientation in the direction of northeast and southwest and low building height-to-street width ratio. Buildings facing each other had cooling effect on surfaces during the morning and evening hours; conversely, they had a warming effect at noon. Clustered trees along the street are effective in reducing the surface temperature compared to scattered and isolated trees. Surface temperature of built up areas was highest at noon, while walls and sidewalks facing northwest were hottest later in the day. Walls and sidewalks that face northwest were warmer than those that face southeast. The surface temperatures of the horizontal street surfaces and of vertical façades are at acceptable levels relative to the surface temperature of similar surfaces in mature cities in subtropical, temperate and Mediterranean climates.

From Theory-Inspired to Theory-Based Interventions: A Protocol for Developing and Testing a Methodology for Linking Behaviour Change Techniques to Theoretical Mechanisms of Action.

Science.gov (United States)

Michie, Susan; Carey, Rachel N; Johnston, Marie; Rothman, Alexander J; de Bruin, Marijn; Kelly, Michael P; Connell, Lauren E

2018-05-18

Understanding links between behaviour change techniques (BCTs) and mechanisms of action (the processes through which they affect behaviour) helps inform the systematic development of behaviour change interventions. This research aims to develop and test a methodology for linking BCTs to their mechanisms of action. Study 1 (published explicit links): Hypothesised links between 93 BCTs (from the 93-item BCT taxonomy, BCTTv1) and mechanisms of action will be identified from published interventions and their frequency, explicitness and precision documented. Study 2 (expert-agreed explicit links): Behaviour change experts will identify links between 61 BCTs and 26 mechanisms of action in a formal consensus study. Study 3 (integrated matrix of explicit links): Agreement between studies 1 and 2 will be evaluated and a new group of experts will discuss discrepancies. An integrated matrix of BCT-mechanism of action links, annotated to indicate strength of evidence, will be generated. Study 4 (published implicit links): To determine whether groups of co-occurring BCTs can be linked to theories, we will identify groups of BCTs that are used together from the study 1 literature. A consensus exercise will be used to rate strength of links between groups of BCT and theories. A formal methodology for linking BCTs to their hypothesised mechanisms of action can contribute to the development and evaluation of behaviour change interventions. This research is a step towards developing a behaviour change 'ontology', specifying relations between BCTs, mechanisms of action, modes of delivery, populations, settings and types of behaviour.

Stress corrosion cracking of Inconel 600 in aqueous solutions at elevated temperature. Pt. II. Effects of chloride and sulphate ions on the electrochemical behaviour of Inconel 600

International Nuclear Information System (INIS)

Ashour, E.A.; Schneider, F.; Mummert, K.

1997-01-01

For pt.I see ibid., p.151-6, 1997. The influencing effects of temperature, potential and electrolyte composition on the electrochemical behaviour of Inconel 600 in aqueous solutions are presented. Considering these effects the connection between the data have been obtained from chemo-mechanical fracture investigation on CT-samples in Part I of this paper and pitting corrosion are discussed. The results have shown that chloride ions depassivate the surfaces of cracks locally and hinder the formation of a new protective oxide layer on the fracture surfaces. Furthermore, chloride promotes the dissolution of metal and initiates the cracking, respectively. The resulting crevice corrosion promotes an increase of hydrogen absorption by the metal. The increase of the hydrogen content of the metal influences the mechanical fracture behaviour. Contrary, sulphate ions inhibit the initiation of corrosion mainly due to a hinderance of chloride ions adsorption on active sites of the fracture surfaces. The initiation of localized corrosion in the crevice region may be stimulated by chromate ions formed by oxidation of chromium from the oxide layer or the base metal in oxygen containing solutions. (orig.)

High-temperature mechanical relaxation in glass-like B2O3

International Nuclear Information System (INIS)

Lomovskoj, V.A.

1987-01-01

The study of high-temperature mechanical relaxation in glass-like B 2 O 3 was carried out at the temperatures from 470 to 620 K using the method of internal friction at freely damped tortional vibrations (frequency range is 0.05 - 10 Hz) and forced torsional vibrations (frequency range is 0.1 -0.00001 Hz). Possible mechanisms of high-temperature mechanical relaxation are considered. It is shown that several possible mechanisms of high-temperature mechanical relaxation in glass-like B 2 O 3 can be singled out. Switching of B-O bridge bond between two boroxol cycles of boroxol grouping for oxygen vacancy in spatial structure of glass-like B 2 O 3 , formed as a result of thermal breaking of one out of three B-O bonds, according to diffusion theory of glass viscosity. The slip of one layer boroxol groupings as to another one in the presence of only tricoordinated boron atoms in the structure of glass-like B 2 O 3

Stress corrosion cracking behaviour of Alloy 600 in high temperature water

International Nuclear Information System (INIS)

Webb, G.L.; Burke, M.G.

1995-01-01

The stress corrosion cracking (SCC) susceptibility of Alloy 600 in deaerated water at 360 deg. C, as measured with statistically-loaded U-bend specimens, is dependent upon microstructure and whether the material was cold-worked and annealed (CWA) or hot-worked and annealed (HWA). All cracking was intergranular, and materials lacking grain boundary carbides were most susceptible to SCC initiation. CWA tubing materials are more susceptible to SCC initiation than HWA ring-rolled forging materials with similar microstructures, as determined by light optical metallography (LOM). In CWA tubing materials one crack dominated and grew to a large size that was observable by visual inspection. HWA materials with a low hot-working finishing temperature (below 925 deg. C) and final anneals at temperatures ranging from 1010 deg. C to 1065 deg. C developed both large cracks, similar to those found in CWA materials, and also small intergranular microcracks, which are detectable only by destructive metallographic examination. HWA materials with a high hot-working finishing temperature (above 980 deg. C) and high-temperature final anneal (above 1040 deg. C), with grain boundaries that are fully decorated, developed only microcracks, which were observed in all specimens examined. These materials developed no large, visually detectable cracks, even after more than 300 weeks exposure. A low-temperature thermal treatment (610 deg. C for 7h), which reduced or eliminates SCC in Alloy 600, did not eliminate microcrack formation in the high temperature processed HWA materials. Detailed microstructural characterization using conventional metallographic and analytical electron microscopy (AEM) techniques was performed on selected materials to identify the factors responsible for the observed differences in cracking behaviour. 11 refs, 12 figs, 3 tabs

Effect of annealing temperature on the mechanical properties of Zircaloy-4 cladding

International Nuclear Information System (INIS)

Beauregard, R.J.; Clevinger, G.S.; Murty, K.L.

1977-01-01

The mechanical properties of Zircaloy cladding materials are sensitive to those fabrication variables which have an effect on the preferred crystallographic orientation or texture of the finished tube. The effect of one such variable, the final annealing temperature, on various mechanical properties is examined using tube reduced Zircaloy-4 fuel rod cladding annealed at temperatures from 905F to 1060F. This temperature range provides cladding with varying degrees of recrystallization including full recrystallization. The burst strength of the cladding at 650F decreased with the annealing temperature reaching a saturation value at approximately 1000F. The total circumferential elongation increased with the annealing temperature reaching a maximum at approximately 1000F and decreasing at higher temperatures. Hoop creep characteristics of Zircaloy cladding were studied as a function of the annealing temperature using closed-end internal pressurization tests at 750F and hoop stresses of 10, 15, 20 and 25 ksi. The effect of annealing temperature on the room temperature mechanical anisotropy parameters, R and P, was studied. The R-parameter was essentially independent of the annealing temperature while the P-parameter increased with annealing temperature. The mechanical anisotropy parameters were also studied as a function of the test temperature from ambient to approximately 800F using continuously monitored high precision extensometry. (Auth.)

Influence of stretch-shortening cycle on mechanical behaviour of triceps surae during hopping.

Science.gov (United States)

Belli, A; Bosco, C

1992-04-01

Six subjects performed a first series of vertical plantar flexions and a second series of vertical rebounds, both involving muscle triceps surae exclusively. Vertical displacements, vertical forces and ankle angles were recorded during the entire work period of 60 seconds per series. In addition, expired gases were collected during the test and recovery for determination of the energy expenditure. Triceps surae was mechanically modelled with a contractile component and with an elastic component. Mechanical behaviour and work of the different muscle components were determined in both series. The net muscular efficiency calculated from the work performed by the centre of gravity was 17.5 +/- 3.0% (mean +/- SD) in plantar flexions and 29.9 +/- 4.8% in vertical rebounds. The net muscle efficiency calculated from the work performed by the contractile component was 17.4 +/- 2.9% in plantar flexions and 16.1 +/- 1.4% in vertical rebounds. These results suggest that the muscular efficiency differences do not reflect muscle contractile component efficiency but essentially the storage and recoil of elastic energy. This is supported by the relationship (P less than 0.01) found in vertical rebounds between the extra work and the elastic component work. A detailed observation of the mechanical behaviour of muscle mechanical components showed that the strategy to maximize the elastic work depends also on the force-velocity characteristics of the movement and that the eccentric-concentric work of the contractile component does not always correspond respectively to the ankle extension-flexion.

Mechanical behaviour of cracked welded structures including mismatch effect

International Nuclear Information System (INIS)

Hornet, P.

2002-01-01

The most important parameters for predicting more precisely the fracture behaviour of welded structures have been identified. In particular, the plasticity development at the crack tip in the ligament appeared as a major parameter to evaluate the yield load of such a complex structure. In this way defect assessments procedures have been developed or modified to take into account the mismatch effect that is to say the mechanical properties of the different material constituting the weld joint. This paper is a synthesis of the work done in the past at Electricite de France on this topic in regards with other work done in France or around the World. The most important parameters which control the plasticity development at the crack tip and so mainly influence the fracture behaviour of welded structures are underlined: the mismatch ratio (weld to base metal yield strength ratio), the mismatch ratio (weld to base metal yield strength ratio), the ligament size and the weld width. Moreover, commonly used fracture toughness testing procedures developed in case of homogeneous specimens cannot be used in a straight forward manner and so has to be modified to take into account the mismatch effect. Number or defect assessment procedures taking into account the mismatch effect by considering the yield load of the welded structure are shortly described. Then, the 'Equivalent Material Method' developed at EDF which allows a good prediction of the applied J-Integral at the crack tip is more detailed. This procedure includes not only both weld and base metal yield strength, the structure geometry, the crack size and the weld dimension using the yield load of the real structures but also includes the effect of both weld and base metal strain hardening exponents. Some validations of this method are proposed. Finally, the ability of finite element modelling to predict the behaviour of such welded structures is demonstrated by modelling real experiments: crack located in the middle of

No effects of huddling on core body temperature in rock hyrax ...

African Journals Online (AJOL)

Huddling is a behavioural energy conservation mechanism that is widely used by many small endotherms at low ambient temperatures. Huddling has many benefits, including decreasing the metabolic cost of maintaining body temperature (Tb), reducing the amount of heat lost to the environment, and increasing the local ...

Influence of Silver nanoparticles addition on the phase transformation, mechanical properties and corrosion behaviour of Cu–Al–Ni shape memory alloys

Energy Technology Data Exchange (ETDEWEB)

Saud, Safaa N.; Hamzah, E., E-mail: esah@fkm.utm.my; Abubakar, T.; Bakhsheshi-Rad, H.R.; Farahany, S.; Abdolahi, A.; Taheri, M.M.

2014-11-05

Highlights: • Thermal analysis showed four different phase β, α, NiAl and γ2 during solidification. • The martensite appeared in the microstructure as a plate and needle like shape. • Shape recovery ratio of 80% was obtained after Ag nanoparticles addition. • Effect of Ag nanoparticles on the corrosion behaviour of Cu–Al–Ni SMA was investigated. - Abstract: Incorporation of silver nanoparticles into Cu-based shape memory alloys is recommended to enhance their phase transformation behaviour. However, this incorporation can affect their transformation temperatures, mechanical, microstructural and corrosion characteristics. Four different phase reactions β, α, NiAl and γ{sub 2} were detected on a derivative curve during the solidification by-computer-aided cooling curve thermal analysis. The highest fraction solid (82%) was calculated for the parent phase (β) based on the Newtonian baseline method. The microstructural changes and mechanical properties were investigated using field emission scanning electron microscopy, X-ray diffraction tensile test and shape memory effect test. It was found that the addition of Ag can control the phase morphology and orientations along with the formation of the Ag-rich precipitates, and thus the tensile strength, elongation, fracture stress–strain, yield strength and shape memory effect are improved. Remarkably, the shape recovery ratio reached approximately 80% of the original shape. The corrosion behaviour of the Cu–Al–Ni shape memory alloy were investigated using electrochemical tests in NaCl solution and their results showed that the corrosion potential (E{sub corr}) of Cu–Al–Ni SMA is shifted towards the nobler direction from −307.4 to −277.1 m V{sub SCE} with the addition of 0.25 wt.% Ag.

Mechanical behavior of aluminum-lithium alloys at cryogenic temperatures

International Nuclear Information System (INIS)

Glazer, J.; Verzasconi, S.L.; Sawtell, R.R.; Morris, J.W. Jr.

1987-01-01

The cryogenic mechanical properties of aluminum-lithium alloys are of interest because these alloys are attractive candidate materials for cryogenic tankage. Previous work indicates that the strength-toughness relationship for alloy 2090-T81 (Al-2.7Cu-2.2Li-0.12Zr by weight) improves significantly as temperature decreases. The subject of this investigation is the mechanism of this improvement. Deformation behavior was studied since the fracture morphology did not change with temperature. Tensile failures in 2090-T81 and -T4 occur at plastic instability. In contrast, in the binary aluminum-lithium alloy studied here they occur well before plastic instability. For all three materials, the strain hardening rate in the longitudinal direction increases as temperature decreases. This increase is associated with an improvement in tensile elongation at low temperatures. In alloy 2090-T4, these results correlate with a decrease in planar slip at low temperatures. The improved toughness at low temperatures is believed to be due to increased stable deformation prior to fracture

A constitutive model for the thermo-mechanical behaviour of fusion-relevant pebble beds and its application to the simulation of HELICA mock-up experimental results

International Nuclear Information System (INIS)

Vella, G.; Maio, P.A. Di; Giammusso, R.; Tincani, A.; Orco, G. Dell

2006-01-01

Within the framework of the activities promoted by European Fusion Development Agreement on the technology of the Helium Cooled Pebble Bed Test Blanket Module to be irradiated in one of the ITER equatorial ports, attention has been focused on the theoretical modelling of the thermo-mechanical constitutive behaviour of both beryllium and lithiated ceramics pebble beds, that are envisaged to act respectively as neutron multiplier and tritium breeder. The thermo-mechanical behaviour of the pebble beds and their nuclear performances in terms of tritium production depend on the reactor relevant conditions (heat flux and neutron wall load), the pebble sizes and the breeder cell geometries (bed thickness, pebble packing factor, bed overall thermal conductivity). ENEA-Brasimone and the Department of Nuclear Engineering (DIN) of the Palermo University have performed intense research activities intended to investigate fusion-relevant pebble bed thermo-mechanical behaviour by adopting both experimental and theoretical approaches. In particular, ENEA has carried out several experimental campaigns on small scale mock-ups tested in out-of-pile conditions, while DIN has developed a proper constitutive model that has been implemented on commercial FEM code, for the prediction of the thermal and mechanical performances of fusion-relevant pebble beds and for the comparison with the experimental results of the ENEA tests. In that framework, HELICA mock-up has been set-up and tested to investigate the behaviour of pebble bed in reactor-relevant geometries, providing useful data sets to be numerically reproduced by means of the DIN constitutive model, contributing to its assessment. The paper presents the constitutive model developed and the main experimental results of two test campaigns on HELICA mock-up carried out at HE-FUS 3 facility of ENEA Brasimone, the geometry of the mock-up, the adopted thermal and mechanical boundary conditions and the test operating conditions. The most

The effect of temperature on the behaviour of marine fishes: A comparison among Atlantic mackerel, Scomber scombrus, bluefish, Pomatomus saltatrix, and tautog, Tautoga onitis

International Nuclear Information System (INIS)

Olla, B.L.; Studholme, A.L.; Bejda, A.J.; Samet, C.; Martin, A.D.

1975-01-01

A comparison was made of the behavioural responses to temperature of Atlantic mackerel, Scomber scombrus, bluefish, Pomatomus saltatrix, and tautog, Tautoga onitis, held under controlled laboratory conditions. When the temperature was either raised or lowered from normal levels, juvenile and adult bluefish and adult Atlantic mackerel, all pelagic species, responded similarly by increasing swimming speed as much as 61-190%. This response was interpreted as a manifestation of behavioural avoidance of a particular level of temperature, indicative of capability for directive movements relative to ambient thermal conditions. Comparing the response of pelagic species to earlier work on tautog, a demersal species, it was clear that avoidance capability is dependent upon the behavioural repertoire of the individual species. The significance of the results, regarding distribution of fish and response potential under thermal stress, is discussed. (author)

Thermomechanical behaviour of boom clay

International Nuclear Information System (INIS)

Sultan, N.; Delage, P.; Cui, Y.J.

2000-01-01

Special attention has been recently paid on temperature effects on the behaviour of deep saturated clays, in relation with nuclear deep waste storage. However, few experimental data are presently available, and existing constitutive models need to be completed. This note is aimed at completing, both experimentally and theoretically, the understanding of the effects of the over-consolidation ration on the thermal volume changes of Boom clay (Belgium). The experimental data obtained here are in a good agreement with existing data. As a complement to existing data, they are used to develop a new elastoplastic model. The adoption of a second coupled plastic mechanism provides good simulations on a complex thermo-mechanical path. (authors)

Mechanical properties of concrete for power reactor at high temperatures

International Nuclear Information System (INIS)

Kawase, Kiyotaka; Tanaka, Hitoshi; Nakano, Masayuki

1985-01-01

The purpose of this study is to investigate the mechanical properties of concrete for power reactor at high temperature. This paper presents the creep behavior of concrete at high temperature and the cause by which a specified aggregate is broken at a specified high temperature. The creep coefficient at high temperature is smaller than that at ordinary temperature. (author)

Behaviour of fibre reinforced polymer confined reinforced concrete columns under fire condition

Science.gov (United States)

Chowdhury, Ershad Ullah

In recent years, fibre reinforced polymer (FRP) materials have demonstrated enormous potential as materials for repairing and retrofitting concrete bridges that have deteriorated from factors such as electro-chemical corrosion and increased load requirements. However, concerns associated with fire remain an obstacle to applications of FRP materials in buildings and parking garages due to FRP's sensitivity to high temperatures as compared with other structural materials and to limited knowledge on their thermal and mechanical behaviour in fire. This thesis presents results from an ongoing study on the fire performance of FRP materials, fire insulation materials and systems, and FRP wrapped reinforced concrete columns. The overall goal of the study is to understand the fire behaviour of FRP materials and FRP strengthened concrete columns and ultimately, provide rational fire safety design recommendations and guidelines for FRP strengthened concrete columns. A combined experimental and numerical investigation was conducted to achieve the goals of this research study. The experimental work consisted of both small-scale FRP material testing at elevated temperatures and full-scale fire tests on FRP strengthened columns. A numerical model was developed to simulate the behaviour of unwrapped reinforced concrete and FRP strengthened reinforced concrete square or rectangular columns in fire. After validating the numerical model against test data available in literature, it was determined that the numerical model can be used to analyze the behaviour of concrete axial compressive members in fire. Results from this study also demonstrated that although FRP materials experience considerable loss of their mechanical and bond properties at temperatures somewhat below the glass transition temperature of the resin matrix, externally-bonded FRP can be used in strengthening concrete structural members in buildings, if appropriate supplemental fire protection system is provided over

Temperature of Steel Columns under Natural Fire

Directory of Open Access Journals (Sweden)

F. Wald

2004-01-01

Full Text Available Current fire design models for time-temperature development within structural elements as well as for structural behaviour are based on isolated member tests subjected to standard fire regimes, which serve as a reference heating, but do not model natural fire. Only tests on a real structure under a natural fire can evaluate future models of the temperature developments in a fire compartment, of the transfer of heat into the structure and of the overall structural behaviour under fire.To study overall structural behaviour, a research project was conducted on an eight storey steel frame building at the  Cardington Building Research Establishment laboratory on January 16, 2003. A fire compartment 11×7 m was prepared on the fourth floor. A fire load of 40 kg/m2 was applied with 100 % permanent mechanical load and 65 % of imposed load. The paper summarises the experimental programme and shows the temperature development of the gas in the fire compartment and of the fire protected columns bearing the unprotected floors.

Mechanical Properties of Low Density Alloys at Cryogenic Temperatures

International Nuclear Information System (INIS)

Jiao, X. D.; Liu, H. J.; Li, L. F.; Yang, K.

2006-01-01

Low-density alloys include aluminum alloys, titanium alloys and magnesium alloys. Aluminum alloys and titanium alloys have been widely investigated and used as structural materials for cryogenic applications because of their light weight and good low-temperature mechanical properties.For aerospace applications, persistent efforts are being devoted to reducing weight and improving performance. Magnesium alloys are the lightest structural alloys among those mentioned above. Therefore, it is necessary to pay attention to magnesium alloys and to investigate their behaviors at cryogenic temperatures. In this paper, we have investigated the mechanical properties and microstructures of some magnesium alloys at cryogenic temperatures. Experimental results on both titanium and magnesium alloys are taken into account in considering these materials for space application

Research on the mechanical behaviour of an airplane component made by selective laser melting technology

Directory of Open Access Journals (Sweden)

Păcurar Răzvan

2017-01-01

Full Text Available The main objective of the presented research consists in the redesign of an airplane component to decrease its weight, without affecting the mechanical behaviour of the component, at the end. Femap NX Nastran and ANSYS FEA programs were used for the shape optimization and for the estimation of the mechanical behaviour of a fixing clamp that was used to sustain the hydraulic pipes that are passing through an airplane fuselage, taking into consideration two types of raw materials – Ti6Al4V and AlSi12 powder from which this component could be manufactured by using the selective laser melting (SLM technology. Based on the obtained results, the airplane component was finally manufactured from titanium alloy using the SLM 250 HL equipment that is available at SLM Solutions GmbH company from Luebeck, in Germany.

Improving the high performance concrete (HPC behaviour in high temperatures

Directory of Open Access Journals (Sweden)

Cattelan Antocheves De Lima, R.

2003-12-01

Full Text Available High performance concrete (HPC is an interesting material that has been long attracting the interest from the scientific and technical community, due to the clear advantages obtained in terms of mechanical strength and durability. Given these better characteristics, HFC, in its various forms, has been gradually replacing normal strength concrete, especially in structures exposed to severe environments. However, the veiy dense microstructure and low permeability typical of HPC can result in explosive spalling under certain thermal and mechanical conditions, such as when concrete is subject to rapid temperature rises, during a f¡re. This behaviour is caused by the build-up of internal water pressure, in the pore structure, during heating, and by stresses originating from thermal deformation gradients. Although there are still a limited number of experimental programs in this area, some researchers have reported that the addition of polypropylene fibers to HPC is a suitable way to avoid explosive spalling under f re conditions. This change in behavior is derived from the fact that polypropylene fibers melt in high temperatures and leave a pathway for heated gas to escape the concrete matrix, therefore allowing the outward migration of water vapor and resulting in the reduction of interned pore pressure. The present research investigates the behavior of high performance concrete on high temperatures, especially when polypropylene fibers are added to the mix.

El hormigón de alta resistencia (HAR es un material de gran interés para la comunidad científica y técnica, debido a las claras ventajas obtenidas en término de resistencia mecánica y durabilidad. A causa de estas características, el HAR, en sus diversas formas, en algunas aplicaciones está reemplazando gradualmente al hormigón de resistencia normal, especialmente en estructuras expuestas a ambientes severos. Sin embargo, la microestructura muy densa y la baja permeabilidad t

Influence of the relative humidity and the temperature on the in-vivo friction behaviour of human skin

NARCIS (Netherlands)

Klaassen, M.; Schipper, D. J.; Masen, M.A.

2016-01-01

Both temperature and relative humidity are known to influence the frictional behaviour of human skin. However, literature does not completely cover to what extent both parameters play a role. Measurements were conducted using an in-house built reciprocating tribometer inside an enclosure in which

Corrosion fatigue crack growth behaviour of low-alloy RPV steels at different temperatures and loading frequencies under BWR/NWC environment

International Nuclear Information System (INIS)

Ritter, S.; Seifert, H.P.

2004-01-01

The strain-induced corrosion cracking or low-frequency corrosion fatigue (LFCF) crack growth behaviour of different reactor pressure vessel (RPV) steels and of a RPV weld filler/weld heat-affected zone (HAZ) material were characterized under simulated transient boiling water reactor/normal water chemistry conditions by cyclic fatigue tests with pre-cracked fracture mechanics specimens. The experiments were performed in oxygenated high-temperature water at temperatures of either 288, 250, 200, or 150 deg. C. Modern high-temperature water loops, on-line crack growth monitoring (DCPD) and fractographic analysis by SEM were used to quantify the cracking response. Under low-flow and highly oxidising conditions (ECP > 0 mV SHE , O 2 = 0.4 ppm) the cycle-based LFCF crack growth rates (CGR) Δa/ΔN increased with decreasing loading frequency and increasing temperature with a maximum/plateau at/above 250 deg. C. Sustained environmentally-assisted crack growth could be maintained down to low frequencies of 10 -5 Hz. The LFCF CGR of low- and high-sulphur steels and of the weld filler/HAZ material were comparable over a wide range of loading conditions and conservatively covered by the 'high-sulphur line' of the General Electric-model. The 'ASME XI wet fatigue CGR curves' could be significantly exceeded in all materials by cyclic fatigue loading at low frequencies ( -2 Hz) at high and low load ratios R. (authors)

Creep behaviour and creep mechanisms of normal and healing ligaments

Science.gov (United States)

Thornton, Gail Marilyn

Patients with knee ligament injuries often undergo ligament reconstructions to restore joint stability and, potentially, abate osteoarthritis. Careful literature review suggests that in 10% to 40% of these patients the graft tissue "stretches out". Some graft elongation is likely due to creep (increased elongation of tissue under repeated or sustained load). Quantifying creep behaviour and identifying creep mechanisms in both normal and healing ligaments is important for finding clinically relevant means to prevent creep. Ligament creep was accurately predicted using a novel yet simple structural model that incorporated both collagen fibre recruitment and fibre creep. Using the inverse stress relaxation function to model fibre creep in conjunction with fibre recruitment produced a superior prediction of ligament creep than that obtained from the inverse stress relaxation function alone. This implied mechanistic role of fibre recruitment during creep was supported using a new approach to quantify crimp patterns at stresses in the toe region (increasing stiffness) and linear region (constant stiffness) of the stress-strain curve. Ligament creep was relatively insensitive to increases in stress in the toe region; however, creep strain increased significantly when tested at the linear region stress. Concomitantly, fibre recruitment was evident at the toe region stresses; however, recruitment was limited at the linear region stress. Elevating the water content of normal ligament using phosphate buffered saline increased the creep response. Therefore, both water content and fibre recruitment are important mechanistic factors involved in creep of normal ligaments. Ligament scars had inferior creep behaviour compared to normal ligaments even after 14 weeks. In addition to inferior collagen properties affecting fibre recruitment and increased water content, increased glycosaminoglycan content and flaws in scar tissue were implicated as potential mechanisms of scar creep

Mechanical Characterisation and Biomechanical and Biological Behaviours of Ti-Zr Binary-Alloy Dental Implants

Directory of Open Access Journals (Sweden)

Aritza Brizuela-Velasco

2017-01-01

Full Text Available The objective of the study is to characterise the mechanical properties of Ti-15Zr binary alloy dental implants and to describe their biomechanical behaviour as well as their osseointegration capacity compared with the conventional Ti-6Al-4V (TAV alloy implants. The mechanical properties of Ti-15Zr binary alloy were characterised using Roxolid© implants (Straumann, Basel, Switzerland via ultrasound. Their biomechanical behaviour was described via finite element analysis. Their osseointegration capacity was compared via an in vivo study performed on 12 adult rabbits. Young’s modulus of the Roxolid© implant was around 103 GPa, and the Poisson coefficient was around 0.33. There were no significant differences in terms of Von Mises stress values at the implant and bone level between both alloys. Regarding deformation, the highest value was observed for Ti-15Zr implant, and the lowest value was observed for the cortical bone surrounding TAV implant, with no deformation differences at the bone level between both alloys. Histological analysis of the implants inserted in rabbits demonstrated higher BIC percentage for Ti-15Zr implants at 3 and 6 weeks. Ti-15Zr alloy showed elastic properties and biomechanical behaviours similar to TAV alloy, although Ti-15Zr implant had a greater BIC percentage after 3 and 6 weeks of osseointegration.

Contributions to the nonlinear modeling of the mechanical behaviour of concrete and of reinforced and prestressed concrete structures

International Nuclear Information System (INIS)

Abbas, Krayani

2007-12-01

The knowledge of the mechanical behaviour of the material and its loading history (at any point of the structure) is necessary to evaluate the tightness of a containment structure and therefore its durability. An elastic plastic non local damage model is developed for modelling the mechanical behaviour of concrete. A regularization technique is introduced on the part responsible of the strain-softening behaviour in order to avoid the numerical problems due to the phenomenon of localisation of damage. The constitutive law and its numerical implementation are detailed. The consistent tangent matrix is derived, where the numerical differentiation technique is applied to integrate plastic constitutive laws and to obtain a quadratic convergence with the Newton-Raphson method at Gauss-point level and in the solution of the boundary value problem. Simulations have shown the capacity of the model to reproduce the classical and complex structural behaviour of concrete. The comparisons with the isotropic damage models illustrate the improvements achieved by introducing the plasticity to the damage formulation: the mode of failure is reproduced correctly (mode I and mixed mode) and the ultimate load is in good agreement with the experimental data. Finally, we present modifications of the classical non local damage model in order to take into account the boundary effects. Our justification is based on micro-mechanical arguments in which the interactions between microcracks are reduced nearby the free boundary. (author)

Effect of applied DC voltages and temperatures on space charge behaviour of multi-layer oil-paper insulation

Energy Technology Data Exchange (ETDEWEB)

Tang Chao; Liao Ruijin [The State Key Laboratory of Power Transmission Equipment and System Security and New Technology, Chongqing University (China); Chen, G [School of Electronics and Computer Science, University of Southampton (United Kingdom); Fu, M, E-mail: tangchao_1981@163.co [AVERA T and D Technology Centre, Stafford (United Kingdom)

2009-08-01

In this paper, space charge in a multi-layer oil-paper insulation system was investigated using the pulsed electroacoustic (PEA) technique. A series of measurements had been carried following subjection of the insulation system to different applied voltages and different temperatures. Charge behaviours in the insulation system were analyzed and the influence of temperature on charge dynamics was discussed. The test results shows that homocharge injection takes place under all the test conditions, the applied DC voltage mainly affects the amount of space charge, while the temperature has greater influence on the distribution and mobility of space charge inside oil-paper samples.

Studying structurally-mechanical characteristics suppositories with amlodipine

Directory of Open Access Journals (Sweden)

Fadi Al Zedan

2013-02-01

Full Text Available Rheological behaviour suppositories with amlodipine on lypofiles to a basis are studied and character of temperature effect on their structurally-mechanical properties is positioned. It is revealed that the temperature of carrying out of technological operations of homogenization and overflow suppositories 50-55ºС is optimum, providing necessary fluidity suppositories masses at hypodispersion in it reacting and aids.

Effect of temperature on synthesis and properties of aluminum-magnesium mechanical alloys

International Nuclear Information System (INIS)

Umbrajkar, Swati M.; Schoenitz, Mirko; Jones, Steven R.; Dreizin, Edward L.

2005-01-01

The synthesis of an Al 0.7 Mg 0.3 mechanical alloy was studied using a planetary mill. Several distinct temperature regimes of mechanical alloying were achieved using milling jars equipped with finned heat sinks and an external air conditioner installed to cool the entire milling chamber. Wireless temperature sensors were attached to the milling jars to monitor the process temperature. Intermediate and final products were collected and were analyzed by electron microscopy and X-ray diffraction. The temperature history of the milling jars exhibited two peaks during mechanical alloying. The first peak occurred when particles of the starting powders deformed to produce flakes. The second peak was observed when the flakes agglomerated and re-fragmented forming layered composites that served as precursors for the mechanical alloy. The temperature of milling affected the magnesium solubility of the produced Al-Mg mechanical alloys. Decreasing the milling temperature from ∼70-80 deg. C to 20-30 deg. C resulted in an increase of the dissolved Mg concentration in Al from 2-3 at.% to ∼25 at.% for the Al 0.7 Mg 0.3 composition. The formation of intermetallic phases was favored at higher milling temperatures, where high solubilities cannot be achieved

Effect of temperature on synthesis and properties of aluminum-magnesium mechanical alloys

Energy Technology Data Exchange (ETDEWEB)

Umbrajkar, Swati M. [New Jersey Institute of Technology, Department of Mechanical Engineering, Newark, NJ 07102-1982 (United States); Schoenitz, Mirko [New Jersey Institute of Technology, Department of Mechanical Engineering, Newark, NJ 07102-1982 (United States); Jones, Steven R. [New Jersey Institute of Technology, Department of Mechanical Engineering, Newark, NJ 07102-1982 (United States); Dreizin, Edward L. [New Jersey Institute of Technology, Department of Mechanical Engineering, Newark, NJ 07102-1982 (United States)]. E-mail: dreizin@njit.edu

2005-10-27

The synthesis of an Al{sub 0.7}Mg{sub 0.3} mechanical alloy was studied using a planetary mill. Several distinct temperature regimes of mechanical alloying were achieved using milling jars equipped with finned heat sinks and an external air conditioner installed to cool the entire milling chamber. Wireless temperature sensors were attached to the milling jars to monitor the process temperature. Intermediate and final products were collected and were analyzed by electron microscopy and X-ray diffraction. The temperature history of the milling jars exhibited two peaks during mechanical alloying. The first peak occurred when particles of the starting powders deformed to produce flakes. The second peak was observed when the flakes agglomerated and re-fragmented forming layered composites that served as precursors for the mechanical alloy. The temperature of milling affected the magnesium solubility of the produced Al-Mg mechanical alloys. Decreasing the milling temperature from {approx}70-80 deg. C to 20-30 deg. C resulted in an increase of the dissolved Mg concentration in Al from 2-3 at.% to {approx}25 at.% for the Al{sub 0.7}Mg{sub 0.3} composition. The formation of intermetallic phases was favored at higher milling temperatures, where high solubilities cannot be achieved.

The influence of isothermal ageing and subsequent hydrogen charging at room temperature on local mechanical properties and fracture characteristics of martensitic-bainitic weldments for power engineering

Directory of Open Access Journals (Sweden)

Falat L.

2017-01-01

Full Text Available The present study deals with the effects of high temperature expositions and subsequent cathodic hydrogen charging of dissimilar martensitic/bainitic weldment on its local mechanical properties and fracture behaviour at room temperature. Circumferential welded joint under investigation was produced by tungsten inert gas welding of X10CrWMoVNb9-2 martensitic and 7CrMoVTiB10-10 bainitic steels tubes with Ni-based filler metal and the application of subcritical postweld heat treatment. Hardness profile measurements revealed pronounced hardness peaks in over-heated regions of the individual steels heat-affected zones which remained preserved also during subsequent expositions at 600°C for up to 5000 hours. Gradual microstructural degradation of these regions included precipitate coarsening and the formation of new secondary phases during thermal exposure. The combined effects of thermal and hydrogen embrittlement of the studied weldment resulted in deleterious effects on its tensile and fracture behaviour.

Multi-scale approach of the mechanical behaviour of reinforced concrete structures - Application to nuclear plant containment buildings

International Nuclear Information System (INIS)

David, M.

2012-01-01

This thesis develops a multi-scale strategy to describe the mechanical behaviour of steel reinforcements and prestressing tendons in a reinforced concrete structure. This strategy is declined in several steps, which allow gradual integration of new physical phenomena. The first asymptotic model represents the effective elastic behaviour of heterogeneities periodically distributed on a surface. It combines an elastic interface behaviour and a membrane behaviour. A second asymptotic model then focuses on the behaviour of rigid fibers distributed on a surface, which may slide with respect to the surrounding volume. These models induce less stress concentrations than the usual truss models. They are implemented in the finite element code Code-Aster, and validated with respect to reference three-dimensional simulations. Their interaction with a macroscopic crack is studied. Finally, this strategy allows the modeling of experimental tests carried out on a portion of a containment building in real scale. (author)

Can there be a T3 ln T kind of behaviour of the low temperature specific heat of liquid 3He without the paramagnons?

International Nuclear Information System (INIS)

Tripathy, D.N.; Mishra, S.

1996-01-01

It is shown that even without invoking the concepts like paramagnons, the temperature dependence of the interparticle correlations in a system of liquid 3 He can give rise a T 3 ln T kind of behaviour of its low temperature fermionic specific heat. It is found to be coming from the self-energy corrections to the bare single particle energy involving the particle-hole propagator. Looking at the similar kind of behaviour observed by us recently for an electron liquid, one may conclude that the T 3 ln T behaviour is perhaps universal for all fermi systems, although for liquid 3 He the very dependence also follows from the paramagnon effects. It is interesting to see that unlike earlier theories, an extremely good fit is obtained with the experimental data over the entire range of low temperatures. (orig.)

Flow behaviour of a heat treated tungsten heavy alloy

International Nuclear Information System (INIS)

Das, Jiten; Sarkar, R.; Rao, G. Appa; Sankaranarayana, M.; Nandy, T.K.; Pabi, S.K.

2012-01-01

Highlights: ► An Arrhenius type of constitutive equation is proposed for the investigated alloy. ► Peierl's controlled dislocation motion is observed at low temperature. ► Transition from Peierl's to forest controlled mechanism is observed at 673 K. ► At room temperature predominantly tungsten grain, cleavage fracture is observed. ► At elevated temperature predominantly intergranular fracture is observed. - Abstract: Flow behaviour of a tungsten heavy alloy was studied in the strain rate-temperature range of 10 −5 –1/s and 298–973 K, respectively. It was observed in this study that the dislocation motion in tungsten heavy alloy was controlled by a Peierl's mechanism at low temperatures (up to 573 K). This was confirmed by the magnitude of apparent activation volume and apparent activation enthalpy as well as TEM observations. Apparent activation enthalpy in the Peierls regime, determined by several methods, was found to vary in between 22 and 37 kJ/mol. An Arrhenius type of constitutive equation was also proposed in the Peierls controlled regime for predicting flow stress as a function of temperature and strain rate. Transition temperature of rate controlling mechanism—from Peierl's mechanism to forest mechanism—was determined from the strain rate sensitivity and apparent activation volume estimation at several temperatures. The transition temperature was found to be about 673 K.

Behaviour of Ca2Fe2O5 with Nb substitution and sintering temperatures seen by Moessbauer spectroscopy

International Nuclear Information System (INIS)

Duhalde, S.; Saragovi, C.; Moraes, I.J.; Terrile, M.C.; Francisco, R.H.P.

1991-01-01

Moessbauer spectroscopy of samples of Ca 2 Fe 2-x Nb x O 5+x with x values ranging from 0 to 0.8 and sintering temperatures of 1200degC and 1300degC shows the presence of two magnetic fields and a paramagnetic signal. The behaviour of the parameters as a function of x and of the sintering temperatures are discussed and compared with XRD results. (orig.)

Mechanism of crack initiation and crack growth under thermal and mechanical fatigue loading

Energy Technology Data Exchange (ETDEWEB)

Utz, S.; Soppa, E.; Silcher, H.; Kohler, C. [Stuttgart Univ. (Germany). Materials Testing Inst.

2013-07-01

The present contribution is focused on the experimental investigations and numerical simulations of the deformation behaviour and crack development in the austenitic stainless steel X6CrNiNb18-10 under thermal and mechanical cyclic loading in HCF and LCF regimes. The main objective of this research is the understanding of the basic mechanisms of fatigue damage and the development of simulation methods, which can be applied further in safety evaluations of nuclear power plant components. In this context the modelling of crack initiation and crack growth inside the material structure induced by varying thermal or mechanical loads are of particular interest. The mechanisms of crack initiation depend among other things on the type of loading, microstructure, material properties and temperature. The Nb-stabilized austenitic stainless steel in the solution-annealed condition was chosen for the investigations. Experiments with two kinds of cyclic loading - pure thermal and pure mechanical - were carried out and simulated. The fatigue behaviour of the steel X6CrNiNb18-10 under thermal loading was studied within the framework of the joint research project [4]. Interrupted thermal cyclic tests in the temperature range of 150 C to 300 C combined with non-destructive residual stress measurements (XRD) and various microscopic investigations, e.g. in SEM (Scanning Electron Microscope), were used to study the effects of thermal cyclic loading on the material. This thermal cyclic loading leads to thermal induced stresses and strains. As a result intrusions and extrusions appear inside the grains (at the surface), at which microcracks arise and evolve to a dominant crack. Finally, these microcracks cause a continuous and significant decrease of residual stresses. The fatigue behaviour of the steel X6CrNiNb18-10 under mechanical loading at room temperature was studied within the framework of the research project [5], [8]. With a combination of interrupted LCF tests and EBSD

Mechanism of crack initiation and crack growth under thermal and mechanical fatigue loading

International Nuclear Information System (INIS)

Utz, S.; Soppa, E.; Silcher, H.; Kohler, C.

2013-01-01

The present contribution is focused on the experimental investigations and numerical simulations of the deformation behaviour and crack development in the austenitic stainless steel X6CrNiNb18-10 under thermal and mechanical cyclic loading in HCF and LCF regimes. The main objective of this research is the understanding of the basic mechanisms of fatigue damage and the development of simulation methods, which can be applied further in safety evaluations of nuclear power plant components. In this context the modelling of crack initiation and crack growth inside the material structure induced by varying thermal or mechanical loads are of particular interest. The mechanisms of crack initiation depend among other things on the type of loading, microstructure, material properties and temperature. The Nb-stabilized austenitic stainless steel in the solution-annealed condition was chosen for the investigations. Experiments with two kinds of cyclic loading - pure thermal and pure mechanical - were carried out and simulated. The fatigue behaviour of the steel X6CrNiNb18-10 under thermal loading was studied within the framework of the joint research project [4]. Interrupted thermal cyclic tests in the temperature range of 150 C to 300 C combined with non-destructive residual stress measurements (XRD) and various microscopic investigations, e.g. in SEM (Scanning Electron Microscope), were used to study the effects of thermal cyclic loading on the material. This thermal cyclic loading leads to thermal induced stresses and strains. As a result intrusions and extrusions appear inside the grains (at the surface), at which microcracks arise and evolve to a dominant crack. Finally, these microcracks cause a continuous and significant decrease of residual stresses. The fatigue behaviour of the steel X6CrNiNb18-10 under mechanical loading at room temperature was studied within the framework of the research project [5], [8]. With a combination of interrupted LCF tests and EBSD

Patterns of cyprinid migration through a fishway in relation to light, water temperature and fish circling behaviour

Czech Academy of Sciences Publication Activity Database

Prchalová, Marie; Slavík, O.; Bartoš, L.

2006-01-01

Roč. 4, č. 3 (2006), s. 213-218 ISSN 1571-5124. [International symposium on Ecohydraulics /5./. Madrid, 12.09.2004-17.09.2004] Institutional research plan: CEZ:AV0Z60170517 Keywords : migration * Cyprinidae * fishway * fish counter * water temperature * weather Subject RIV: EH - Ecology, Behaviour

Use of the mechanical equation of states to predict the behaviour of 20 Cr-25 Ni-Nb stainless steel nuclear fuel cladding

International Nuclear Information System (INIS)

Gittus, J.H.

1975-01-01

Stress-analysis techniques such as the finite-element method demand prediction techniques capable of forecasting creep-rate as a function of the instantaneous and previous values of temperature and stress at each node. To supply this requirement, for metals that creep by dislocation-movement, a Mechanical Equation of States (MEOS) has been developed from the theory of dislocation-interactions and compared with creep data. Parameter-values for the MEOS have been determined, in the case of stainless steel, by stress-removal and stress-reversal (creep-fatigue) experiments. Both the plastic and anelastic (recoverable) components of creep-strain are predicted by the MEOS for any arbitary history of temperature and multiaxial stresses. Its predictions compare well with the actual results of stress-dip experiments. By generalizing to the multiaxial case, an algorithm is produced which solves the MEOS. Input data for stainless steel are tabulated. The predicted multiaxial strain-time behaviour is presented for a stainless steel nuclear fuel cladding tube subjected to a stress temperature history similar to that expected in service. (author)

Frequency and temperature dependence behaviour of impedance, modulus and conductivity of BaBi4Ti4O15 Aurivillius ceramic

Directory of Open Access Journals (Sweden)

Tanmaya Badapanda

2014-09-01

Full Text Available In this work, we report the dielectric, impedance, modulus and conductivity study of BaBi4Ti4O15 ceramic synthesized by solid state reaction. X-ray diffraction (XRD pattern showed orthorhombic structure with space group A21am confirming it to be an m = 4 member of the Aurivillius oxide. The frequency dependence dielectric study shows that the value of dielectric constant is high at lower frequencies and decreases with increase in frequency. Impedance spectroscopy analyses reveal a non-Debye relaxation phenomenon since relaxation frequency moves towards the positive side with increase in temperature. The shift in impedance peaks towards higher frequency side indicates conduction in material and favouring of the long rangemotion of mobile charge carriers. The Nyquist plot from complex impedance spectrum shows only one semicircular arc representing the grain effect in the electrical conduction. The modulus mechanism indicates the non-Debye type of conductivity relaxation in the material, which is supported by impedance data. Relaxation times extracted using imaginary part of complex impedance (Z′′ and modulus (M′′ were also found to follow Arrhenius law. The frequency dependent AC conductivity at different temperatures indicates that the conduction process is thermally activated. The variation of DC conductivity exhibits a negative temperature coefficient of resistance behaviour.

Behavioural, hormonal and neurobiological mechanisms of aggressive behaviour in human and nonhuman primates.

Science.gov (United States)

de Almeida, Rosa Maria Martins; Cabral, João Carlos Centurion; Narvaes, Rodrigo

2015-05-01

Aggression is a key component for social behaviour and can have an adaptive value or deleterious consequences. Here, we review the role of sex-related differences in aggressive behaviour in both human and nonhuman primates. First, we address aggression in primates, which varies deeply between species, both in intensity and in display, ranging from animals that are very aggressive, such as chimpanzees, to the nonaggressive bonobos. Aggression also influences the hierarchical structure of gorillas and chimpanzees, and is used as the main tool for dealing with other groups. With regard to human aggression, it can be considered a relevant adaptation for survival or can have negative impacts on social interaction for both sexes. Gender plays a critical role in aggressive and competitive behaviours, which are determined by a cascade of physiological changes, including GABAergic and serotonergic systems, and sex neurosteroids. The understanding of the neurobiological bases and behavioural determinants of different types of aggression is fundamental for minimising these negative impacts. Copyright © 2015 Elsevier Inc. All rights reserved.

Dual mechanical behaviour of hydrogen in stressed silicon nitride thin films

International Nuclear Information System (INIS)

Volpi, F.; Braccini, M.; Pasturel, A.; Devos, A.; Raymond, G.; Morin, P.

2014-01-01

In the present article, we report a study on the mechanical behaviour displayed by hydrogen atoms and pores in silicon nitride (SiN) films. A simple three-phase model is proposed to relate the physical properties (stiffness, film stress, mass density, etc.) of hydrogenated nanoporous SiN thin films to the volume fractions of hydrogen and pores. This model is then applied to experimental data extracted from films deposited by plasma enhanced chemical vapour deposition, where hydrogen content, stress, and mass densities range widely from 11% to 30%, −2.8 to 1.5 GPa, and 2.0 to 2.8 g/cm 3 , respectively. Starting from the conventional plotting of film's Young's modulus against film porosity, we first propose to correct the conventional calculation of porosity volume fraction with the hydrogen content, thus taking into account both hydrogen mass and concentration. The weight of this hydrogen-correction is found to evolve linearly with hydrogen concentration in tensile films (in accordance with a simple “mass correction” of the film density calculation), but a clear discontinuity is observed toward compressive stresses. Then, the effective volume occupied by hydrogen atoms is calculated taking account of the bond type (N-H or Si-H bonds), thus allowing a precise extraction of the hydrogen volume fraction. These calculations applied to tensile films show that both volume fractions of hydrogen and porosity are similar in magnitude and randomly distributed against Young's modulus. However, the expected linear dependence of the Young's modulus is clearly observed when both volume fractions are added. Finally, we show that the stiffer behaviour of compressive films cannot be only explained on the basis of this (hydrogen + porosity) volume fraction. Indeed this stiffness difference relies on a dual mechanical behaviour displayed by hydrogen atoms against the film stress state: while they participate to the stiffness in compressive films, hydrogen atoms mainly

Hormonal and neural mechanisms of food reward, eating behaviour and obesity.

Science.gov (United States)

Murray, Susan; Tulloch, Alastair; Gold, Mark S; Avena, Nicole M

2014-09-01

With rising rates of obesity, research continues to explore the contributions of homeostatic and hedonic mechanisms related to eating behaviour. In this Review, we synthesize the existing information on select biological mechanisms associated with reward-related food intake, dealing primarily with consumption of highly palatable foods. In addition to their established functions in normal feeding, three primary peripheral hormones (leptin, ghrelin and insulin) play important parts in food reward. Studies in laboratory animals and humans also show relationships between hyperphagia or obesity and neural pathways involved in reward. These findings have prompted questions regarding the possibility of addictive-like aspects in food consumption. Further exploration of this topic may help to explain aberrant eating patterns, such as binge eating, and provide insight into the current rates of overweight and obesity.

Hydro-mechanical analysis of results acquired by video-observations and deformation measurements performed in boreholes in the Opalinus clay of the URL Mont Terri supported by laboratory investigations on the hydro-mechanical behaviour of Opalinus clay

International Nuclear Information System (INIS)

Seeska, R.; Rutenberg, M.; Lux, K.H.

2012-01-01

also be detected. Furthermore, a significant influence of the hydraulic behaviour on the load-bearing and deformation behaviour of the investigated boreholes was observed. Therefore, laboratory investigations regarding the hydraulic sensitivity of Opalinus Clay have been performed in the TUC rock mechanic laboratory on rock samples from the URL Mont Terri in addition to the in-situ observations. To investigate the hydraulic sensitivity and the hydro-mechanically coupled behaviour of the clay-stone samples, a series of uniaxial strength tests with precisely controlled relative humidity and temperature of the air surrounding the specimen inside the test rig has been performed. Eventually, an attempt has been made to hydro-mechanically model the observed borehole behaviour by using a three-dimensional model covering a drift section and a borehole within the near field of the drift. The numerical simulations have been performed using an elastoplastic constitutive model named ubiquitous joint. Implemented in the FLAC3D software code, the constitutive model ubiquitous joint is capable of modelling the mechanical behaviour of the rock matrix as well as the highly anisotropic mechanical behaviour of the bedding planes. Furthermore, effects like time dependent desaturation of the rock mass, a reduction of strength in the damaged zones around the drift and the borehole, and the increase of hydraulic permeability within the damaged zones have also been taken into consideration when performing the numerical simulations. Figure 2 exemplarily shows the calculated pore pressure distribution around the drift and the borehole in a cross section along the borehole's longitudinal axis. The presentation includes a brief discussion of the results obtained by the logging tool and the discussion of the borehole videos that were recorded by the axial borehole camera as well as a discussion of the laboratory results before in the concluding part the results of the numerical simulations will be

Effect of ageing time and temperature on the strain ageing behaviour of quenched zircaloy-4

International Nuclear Information System (INIS)

Rheem, K.S.; Park, W.K.; Yook, C.C.

1977-01-01

The strain ageing behaviour of quenched Zircaloy-4 has been studied as a function of ageing time and temperature in the temperature range 523-588 K for a short-ageing time of 1 to 52 seconds. A the test conditions, the strain ageing stress increased with ageing time and temperature at a strain rate of 5.55x10 -4 sec -1 . Applying stress on the quenched Zircaloy-4, the strain ageing effect indicated following two states: an initial stage having an activation energy of 0.39ev considered to be due to Snoek type ordering of interstitial oxygen atoms in the stress field of a dislocaiton and a second stage havingan activation energy of 0.60 ev, due to mainly long range diffusion of oxygen atoms. (author)

Experimental and numerical analysis of the static and dynamic crack growth resistance behaviour of structural steels in the temperature range from 20 C to 350 C

International Nuclear Information System (INIS)

Aurich, D.; Gerwien, P.; Huenecke, J.; Klingbeil, D.; Krafka, H.; Kuenecke, G.; Ohm, K.; Veith, H.; Wossidlo, P.; Haecker, R.

1998-01-01

The crack growth resistance behaviour of the steels StE 460 and 22NiMoCr3-7 was determined in the temperature range from 23 C to 350 C by means of C(T), M(T), and ISO-V specimens tested under quasistatic and dynamic loads. The Russian steel 15Ch2NMFA-A was tested at room temperature and 50 C. In the steels StE 460 and 22 NiMoCr3-7, the minimum crack growth resistance is observed at about 250 C, with measured values always being higher for the latter steel type. The crack growth resistance behaviour of the tested materials correlates with the behaviour of flow curve, yield strength, and notch impact toughness as a function of temperature. Impact tests of ISO-V specimens give higher crack resistance values than quasistatic load tests, and the temperature dependence is significantly lower than those of specimens tested under static loads. A metallurgical analysis of the materials shows the causes of the dissimilar behaviour. The stretching zones determined for the C(T) specimen correspond to the toughness of the steels examined, and they are not much influenced by the temperature. The numerical analysis using damaging models for simulation of ductile crack growth is reported for all specimen types and two different temperatures each. (orig./CB) [de

Temperature dependence of poly(lactic acid) mechanical properties

DEFF Research Database (Denmark)

Zhou, Chengbo; Guo, Huilong; Li, Jingqing

2016-01-01

The mechanical properties of polymers are not only determined by their structures, but also related to the temperature field in which they are located. The yield behaviors, Young's modulus and structures of injection-molded poly(lactic acid) (PLA) samples after annealing at different temperatures....... The crystallinity increases with increasing annealing temperature and a' form crystal is formed when the annealing temperature is higher than 100 oC. The stretched samples with low crystallinity show the first yield at draw temperatures below the glass transition temperature (Tg) and the second yield above Tg....... For the samples annealed between 80 and 120 oC, a peculiar double yield appears when stretched within 50–60 oC and only the first or the second yield can be found at the lower and higher draw temperatures. The yield strain and yield stress together with Young's modulus were obtained and discussed in terms...

Mechanism of high-temperature resistant water-base mud

Energy Technology Data Exchange (ETDEWEB)

Luo, P

1981-01-01

Based on experiments, the causes and laws governing the changes in the performance of water-base mud under high temperature are analyzed, and the requisites and mechanism of treating agents resisting high temperature are discussed. Ways and means are sought for inhibiting, delaying and making use of the effect of high temperature on the performance of mud, while new ideas and systematic views have been expressed on the preparation of treating agents and set-up of a high temperature resistant water-base mud system. High temperature dispersion and high temperature surface inactivation of clay in the mud, as well as their effect and method of utilization are reviewed. Subjects also touched upon include degradation and cross-linking of the high-temperature resistant treating agents, their use and effect. Based on the above, the preparation of a water-base and system capable of resisting 180 to 250/sup 0/C is recommended.

Room and elevated temperature Mechanical Behavior of 9-12% Cr Steels

Energy Technology Data Exchange (ETDEWEB)

Dogan, Omer N.; Hawk, Jeffrey A.; Schrems, Karol K.

2005-02-01

The mechanical properties of medium Cr steels used in fossil fired power plants are very good because of their excellent high temperature microstructural stability. However, as the desire to increase the operating temperature (>650C) of the plant goes up, the need for steels that maintain their strength at these temperatures also increases. The mechanical properties of three medium Cr steels (0.08C-(9-12)Cr-1.2Ni-0.7Mo-3.0Cu-3.0Co-0.5Ti) were investigated through hardness, hot hardness and tensile measurements. The strength of the 9-12%Cr steels at room temperature after long-term isothermal aging (750C; 1000 hours) compares favorably with that of other power plant steels (e.g., P91). In addition, the elevated temperature strength and hot hardness also behave similarly. The mechanical behavior will be discussed in terms of the strength, elongation and tensile fracture characteristics.

Mechanical properties of LMR structural materials at high temperature

International Nuclear Information System (INIS)

Kim, D. W.; Kuk, I. H.; Ryu, W. S. and others

1999-03-01

Austenitic stainless is used for the structural material of liquid metal reactor (LMR) because of good mechanical properties at high temperature. Stainless steel having more resistant to temperature by adding minor element has been developing for operating the LMR at higher temperature. Of many elements, nitrogen is a prospective element to modify type 316L(N) stainless steel because nitrogen is the most effective element for solid solution and because nitrogen retards the precipitation of carbide at grain boundary. Ti, Nb, and V are added to improve creep properties by stabilizing the carbides through forming MC carbide. Testing techniques of tensile, fatigue, creep, and creep-fatigue at high temperature are difficult. Moreover, testing times for creep and creep-fatigue tests are very long up to several tens of thousands hours because creep and creep-fatigue phenomena are time-dependent damage mechanism. So, it is hard to acquire the material data for designing LMR systems during a limited time. In addition, the integrity of LMR structural materials at the end of LMR life has to be predicted from the laboratory data tested during the short term because there is no data tested during 40 years. Therefore, the effect of elements on mechanical properties at high temperature was reviewed in this study and many methods to predict the long-term behaviors of structural materials by simulated modelling equation is shown in this report. (author). 32 refs., 9 tabs., 38 figs

Temperature behaviour of optical parameters in (Ag3AsS3)0.3(As2S3)0.7 thin films

Science.gov (United States)

Kutsyk, Mykhailo M.; Ráti, Yosyp Y.; Izai, Vitalii Y.; Makauz, Ivan I.; Studenyak, Ihor P.; Kökényesi, Sandor; Komada, Paweł; Zhailaubayev, Yerkin; Smailov, Nurzhigit

2015-12-01

(Ag3AsS3)0.3(As2S3)0.7 thin films were deposited onto a quartz substrate by rapid thermal evaporation. The optical transmission spectra of thin films were measured in the temperature range 77-300 K. It is shown that the absorption edge spectra are described by the Urbach rule. The temperature behaviour of absorption spectra was studied, the temperature dependences of energy position of absorption edge and Urbach energy were investigated. The influence of transition from three-dimensional glass to the two-dimensional thin film as well as influence of Ag3AsS3 introduction into As2S3 on the optical parameters of (Ag3AsS3)0.3(As2S3)0.7 were analysed. The spectral and temperature behaviour or refractive index for (Ag3AsS3)0.3(As2S3)0.7 thin film were studied.

Numerical modelling of the long term mechanical behaviour of a storage cell for high level nuclear wastes

International Nuclear Information System (INIS)

Bian, H.B.; Jia, Y.; Duveau, G.; Shao, J.F.; Poutrel, A.

2010-01-01

Document available in extended abstract form only. In France, a clay formation, called Callovo-Oxfordian clay, is considered as potential geological barrier for storage of radioactive wastes. An underground research laboratory is constructed in this clay layer in Bure (CMHM). The French Radioactive Waste Management Agency (Andra) plans to conduct a series of full scale experiments in the Bure Underground Research Laboratory in order to study the coupled Chemo- Thermo-Hydraulic-Mechanical processes due to the excavation, ventilation, subsequent backfilling/sealing, corrosion of metal components and heat release from the radioactive wasters. These phenomena will occur in the storage structures and the geologic barrier for a short/very long period of time. Especially for the High-Level Wastes, due to the important increase of temperature released by the waste packages, the behaviour of geological barrier is perhaps perturbed and the design of repository is also influenced in terms of admissible thermal loading. In this paper, a disposal cell for the radioactive High-Level Wastes (HLW) is studied in order to analyser the coupled phenomena evolving in the HLW storage. The carbon steel is adopted as the first choice material for the container of waste because of its relevant geochemical condition. In the underground radioactive wastes storage, due to the arrival of water from the geological formation, the metallic components will be corroded, by step, with a decrease of mechanical resistance and a generated supplementary volume. The space between the metallic container and the host rock will then be closed under the combination of metallic corrosion and the behaviour differs of Callovo-Oxfordian clay. As results, important stress will be created on the interface of Callovo-Oxfordian clay and wastes packages. In addition, local hydration of barrier modifies the water infiltration from the Callovo-Oxfordian clay and the stress distribution in the argillite. According to

Analysis of the structural behaviour of colonic segments by inflation tests: Experimental activity and physio-mechanical model.

Science.gov (United States)

Carniel, Emanuele L; Mencattelli, Margherita; Bonsignori, Gabriella; Fontanella, Chiara G; Frigo, Alessandro; Rubini, Alessandro; Stefanini, Cesare; Natali, Arturo N

2015-11-01

A coupled experimental and computational approach is provided for the identification of the structural behaviour of gastrointestinal regions, accounting for both elastic and visco-elastic properties. The developed procedure is applied to characterize the mechanics of gastrointestinal samples from pig colons. Experimental data about the structural behaviour of colonic segments are provided by inflation tests. Different inflation processes are performed according to progressively increasing top pressure conditions. Each inflation test consists of an air in-flow, according to an almost constant increasing pressure rate, such as 3.5 mmHg/s, up to a prescribed top pressure, which is held constant for about 300 s to allow the development of creep phenomena. Different tests are interspersed by 600 s of rest to allow the recovery of the tissues' mechanical condition. Data from structural tests are post-processed by a physio-mechanical model in order to identify the mechanical parameters that interpret both the non-linear elastic behaviour of the sample, as the instantaneous pressure-stretch trend, and the time-dependent response, as the stretch increase during the creep processes. The parameters are identified by minimizing the discrepancy between experimental and model results. Different sets of parameters are evaluated for different specimens from different pigs. A statistical analysis is performed to evaluate the distribution of the parameters and to assess the reliability of the experimental and computational activities. © IMechE 2015.

The effect of temperature and concentration on the corrosion inhibition mechanism of an amphiphilic amido-amine in CO2 saturated solution

International Nuclear Information System (INIS)

Desimone, M.P.; Gordillo, G.; Simison, S.N.

2011-01-01

Highlights: → Behaviour of N-[2-[(2-aminoethyl)amino]ethyl]-9-octadecenamide (AAOA) as CO 2 corrosion inhibitor. → The adsorption of the AAOA corrosion inhibitor obeys a Frumkin adsorption isotherm. → The inhibition efficiency of the AAOA depends on temperature and concentration. → There is a change in the adsorption mode of the inhibitor with concentration. → AAOA is mainly physi- or chemisorbed for low or high concentrations, respectively. - Abstract: The corrosion inhibition mechanism of the N-[2-[(2-aminoethyl)amino]ethyl]-9-octadecenamide on mild steel surface in CO 2 -saturated 5% NaCl solution has been studied. The inhibition efficiency decreases with increasing temperature. Adsorption of the inhibitor studied is found to follow the Frumkin adsorption isotherm. EIS results show that the mechanism of its corrosion inhibition at concentrations higher than critical micelle concentration is by forming a protective porous bi-layer. The activation energy, thermodynamic parameters and electrochemical results reveal a change in the adsorption mode of the inhibitor studied: the inhibitor could primarily be physically adsorbed at low concentrations, while chemisorption is favoured as concentration increases.

Mechanical Behaviour of Stainless Steels under Dynamic Loading: An Investigation with Thermal Methods

Directory of Open Access Journals (Sweden)

Rosa De Finis

2016-11-01

Full Text Available Stainless steels are the most exploited materials due to their high mechanical strength and versatility in producing different alloys. Although there is great interest in these materials, mechanical characterisation, in particular fatigue characterisation, requires the application of several standardised procedures involving expensive and time-consuming experimental campaigns. As a matter of fact, the use of Standard Test Methods does not rely on a physical approach, since they are based on a statistical evaluation of the fatigue limit with a fixed probabilistic confidence. In this regard, Infra-Red thermography, the well-known, non-destructive technique, allows for the development of an approach based on evaluation of dissipative sources. In this work, an approach based on a simple analysis of a single thermographic sequence has been presented, which is capable of providing two indices of the damage processes occurring in material: the phase shift of thermoelastic signal φ and the amplitude of thermal signal at twice the loading frequency, S2. These thermal indices can provide synergetic information about the mechanical (fatigue and fracture behaviour of austenitic AISI 316L and martensitic X4 Cr Ni Mo 16-5-1; since they are related to different thermal effects that produce damage phenomena. In particular, the use of φ and S2 allows for estimation of the fatigue limit of stainless steels at loading ratio R = 0.5 in agreement with the applied Standard methods. Within Fracture Mechanics tests, both indices demonstrate the capacity to localize the plastic zone and determine the position of the crack tip. Finally, it will be shown that the value of the thermoelastic phase signal can be correlated with the mechanical behaviour of the specific material (austenitic or martensitic.

Temperature-dependent dynamic mechanical properties of magnetorheological elastomers under magnetic field

Energy Technology Data Exchange (ETDEWEB)

Ju, Benxiang, E-mail: jubenxiang@qq.com [National Instrument Functional Materials Engineering Technology Research Center, Chongqing 400707 (China); Tang, Rui; Zhang, Dengyou; Yang, Bailian [National Instrument Functional Materials Engineering Technology Research Center, Chongqing 400707 (China); Yu, Miao; Liao, Changrong [College of Optoelectronic Engineering, Chongqing University, Chongqing 400044 (China)

2015-01-15

Both anisotropic and isotropic magnetorheological elastomer (MRE) samples were fabricated by using as-prepared polyurethane (PU) matrix and carbonyl iron particles. Temperature-dependent dynamic mechanical properties of MRE were investigated and analyzed. Due to the unique structural features of as-prepared matrix, temperature has a greater impact on the properties of as-prepared MRE, especially isotropic MRE. With increasing of temperature and magnetic field, MR effect of isotropic MRE can reach up to as high as 4176.5% at temperature of 80 °C, and the mechanism of the temperature-dependent in presence of magnetic field was discussed. These results indicated that MRE is a kind of temperature-dependent material, and can be cycled between MRE and MR plastomer (MRP) by varying temperature. - Highlights: • Both anisotropic and isotropic MRE were fabricated by using as-prepared matrix. • Temperature-dependent properties of MRE under magnetic field were investigated. • As-prepared MRE can transform MRE to MRP by adjusting temperature.

Characterisation of Ground Thermal and Thermo-Mechanical Behaviour for Shallow Geothermal Energy Applications

DEFF Research Database (Denmark)

Vieira, Ana; Alberdi-Pagola, Maria; Christodoulides, Paul

2017-01-01

Increasing use of the ground as a thermal reservoir is expected in the near future. Shallow geothermal energy (SGE) systems have proved to be sustainable alternative solutions for buildings and infrastructure conditioning in many areas across the globe in the past decades. Recently novel solutions......-hydro-mechanical behaviour of soil is introduced and discussed. These coupled processes are important for confirming the structural integrity of energy geostructures, but routine methods for parameter determination are still lacking (Energies). Keywords: shallow geothermal systems; soil thermal behaviour; laboratory testing......, including energy geostructures, where SGE systems are coupled with foundation heat exchangers, have also been developed. The performance of these systems is dependent on a series of factors, among which the thermal properties of the soil play a major role. The purpose of this paper is to present...

Elevated temperature erosive wear of metallic materials

International Nuclear Information System (INIS)

Roy, Manish

2006-01-01

Solid particle erosion of metals and alloys at elevated temperature is governed by the nature of the interaction between erosion and oxidation, which, in turn, is determined by the thickness, pliability, morphology, adhesion characteristics and toughness of the oxide scale. The main objective of this paper is to critically review the present state of understanding of the elevated temperature erosion behaviour of metals and alloys. First of all, the erosion testing at elevated temperature is reviewed. This is followed by discussion of the essential features of elevated temperature erosion with special emphasis on microscopic observation, giving details of the erosion-oxidation (E-O) interaction mechanisms. The E-O interaction has been elaborated in the subsequent section. The E-O interaction includes E-O maps, analysis of transition criteria from one erosion mechanism to another mechanism and quantification of enhanced oxidation kinetics during erosion. Finally, the relevant areas for future studies are indicated. (topical review)

Analysis of the competition between brittle and ductile fracture: application for the mechanical behaviour of C-Mn and theirs welds

International Nuclear Information System (INIS)

Le Corre, V.

2006-09-01

This study deals with the fracture behaviour of welded thin structures in the ductile to brittle transition range. It aims to propose a criterion to define the conditions for which the risk of fracture by cleavage does not exist on a cracked structure. The literature review shows that the difficulties of prediction of the fracture behaviour of a structure are related to the dependence of the fracture probability to the mechanical fields at the crack tip. The ductile to brittle transition range thus depends on the studied geometry of the structure. A threshold stress, below which cleavage cannot take place, is defined using fracture tests on notched specimens broken at very low temperature. The finite element numerical simulation of fracture tests on CT specimens in the transition range shows a linear relationship between the fracture probability and the volume exceeding the threshold stress, thus showing the relevance of the proposed criterion. Moreover, several relations are established allowing to simplify the identification of the criterion parameters. The criterion is applied to a nuclear structural C-Mn steel, by focusing more particularly on the higher boundary of the transition range. A fracture test on a full-scale pipe is designed, developed, carried out and analysed using its numerical simulation. The results show firstly that, on the structure, the transition range is shifted in temperature, compared to laboratory specimens, due to the low plasticity constraint achieved in thin structures, and secondly that the threshold stress criterion allows to estimate simply this shift. (author)

Characterization of ash melting behaviour at high temperatures under conditions simulating combustible solid waste gasification.

Science.gov (United States)

Niu, Miaomiao; Dong, Qing; Huang, Yaji; Jin, Baosheng; Wang, Hongyan; Gu, Haiming

2018-05-01

To achieve high-temperature gasification-melting of combustible solid waste, ash melting behaviour under conditions simulating high-temperature gasification were studied. Raw ash (RA) and gasified ash (GA) were prepared respectively by waste ashing and fluidized bed gasification. Results of microstructure and composition of the two-ash indicated that GA showed a more porous structure and higher content of alkali and alkali earth metals among metallic elements. Higher temperature promoted GA melting and could reach a complete flowing state at about 1250°C. The order of melting rate of GA under different atmospheres was reducing condition > inert condition > oxidizing condition, which might be related to different existing forms of iron during melting and different flux content with atmosphere. Compared to RA, GA showed lower melting activity at the same condition due to the existence of an unconverted carbon and hollow structure. The melting temperature for sufficient melting and separation of GA should be at least 1250°C in this work.

Temperature-induced changes in neuromuscular function: central and peripheral mechanisms.

Science.gov (United States)

Goodman, D; Hancock, P A; Runnings, D W; Brown, S L

1984-10-01

Three series of experimental tests were conducted on subjects under both elevated and depressed thermal conditions. Tripartite series consisted of whole-body immersion excepting the head, whole-body immersion excepting the head and response limb, and immersion of the discrete-response limb. Measures of physiological and behavioural responses were made at sequential .4 degrees C changes during whole-body immersions and approximately 5 degrees C changes of water temperature during the immersion of a limb only. Results suggested that velocity of nerve conduction decreased with thermal depression. Premotor, motor, simple, and choice reaction times varied differentially as a function of the hot and cold conditions. Implications of these differential effects on neuromuscular function are examined with respect to person-machine performance in artificially induced or naturally occurring extremes of ambient temperature.

Characterization of polymer surface structure and surface mechanical behaviour by sum frequency generation surface vibrational spectroscopy and atomic force microscopy

International Nuclear Information System (INIS)

Opdahl, Aric; Koffas, Telly S; Amitay-Sadovsky, Ella; Kim, Joonyeong; Somorjai, Gabor A

2004-01-01

Sum frequency generation (SFG) vibrational spectroscopy and atomic force microscopy (AFM) have been used to study polymer surface structure and surface mechanical behaviour, specifically to study the relationships between the surface properties of polymers and their bulk compositions and the environment to which the polymer is exposed. The combination of SFG surface vibrational spectroscopy and AFM has been used to study surface segregation behaviour of polyolefin blends at the polymer/air and polymer/solid interfaces. SFG surface vibrational spectroscopy and AFM experiments have also been performed to characterize the properties of polymer/liquid and polymer/polymer interfaces, focusing on hydrogel materials. A method was developed to study the surface properties of hydrogel contact lens materials at various hydration conditions. Finally, the effect of mechanical stretching on the surface composition and surface mechanical behaviour of phase-separated polyurethanes, used in biomedical implant devices, has been studied by both SFG surface vibrational spectroscopy and AFM. (topical review)

Mechanism for elevated temperature leaching