Flame and flameless atomic-absorption determination of tellurium in geological materials

Science.gov (United States)

Chao, T.T.; Sanzolone, R.F.; Hubert, A.E.

1978-01-01

The sample is digested with a solution of hydrobromic acid and bromine and the excess of bromine is expelled. After dilution of the solution to approximately 3 M in hydrobromic acid, ascorbic acid is added to reduce iron(III) before extraction of tellurium into methyl isobutyl ketone (MIBK). An oxidizing air-acetylene flame is used to determine tellurium in the 0.1-20 ppm range. For samples containing 4-200 ppb of tellurium, a carbon-rod atomizer is used after the MIBK extract has been washed with 0.5 M hydrobromic acid to remove the residual iron. The flame procedure is useful for rapid preliminary monitoring, and the flameless procedure can determine tellurium at very low concentrations. ?? 1978.

Release of tellurium and cesium from UO2 in LWR fuel rods during irradiation

International Nuclear Information System (INIS)

Malen, K.A.

1983-01-01

In this paper the release of tellurium (Te-132) and cesium (Cs-134 and Cs-137) from UO 2 -fuel is analyzed. The basis for the analysis is the experimental results from the S176 series of experiments performed at Studsvik. It seems that the model developed earlier for release of iodine applies also to tellurium and cesium. This model assumes sweeping up of the species in question by moving grain boundaries and subsequent release through grain boundary porosity. An interesting extra feature is deposition of tellurium at temperatures in the range 1500-2000 K believed to be due to condensation. (author)

Tellurium chemistry, tellurium release and deposition during the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Sallach, R.A.; Osetek, D.J.; Hobbins, R.R.; Akers, D.W.

1985-01-01

This paper presents the chemistry and estimated behavior of tellurium during and after the accident at Three Mile Island Unit-2. The discussion of tellurium behavior is based on all available measurement data for /sup 129m/Te, 132 Te, stable tellurium ( 126 Te, 128 Te, and 130 Te), and best estimate calculations of tellurium release and transport. Results from Oak Ridge National Laboratory (ORNL) tests, Power Burst Facility (PBF) Severe Fuel Damage Tests at Idaho National Engineering Laboratory (INEL) and SASCHA tests from Karlsruhe, W. Germany are compared with calculated release fractions and samples taken from TMI Unit-2. It is concluded that very little tellurium was released and transported from the TMI-2 core, probably as a result of holdup by zircaloy cladding and other structural materials. 37 refs., 12 figs., 4 tabs

Tellurium chemistry, tellurium release and deposition during the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Sallach, R.A.; Osetek, D.J.; Hobbins, R.R.; Akers, D.W.

1985-08-01

This report presents the chemistry and estimated behavior of tellurium during and after the accident at Three Mile Island Unit-2. The discussion of tellurium behavior is based on all available measurement data for /sup 129 m/Te, 132 Te, stable tellurium ( 126 Te, 128 Te, and 130 Te), and best estimate calculations of tellurium release and transport. Results from Oak Ridge National Laboratory (ORNL) tests, Power Burst Facility (PBF) Severe Fuel Damage Tests at Idaho National Engineering Laboratory (INEL) and SASCHA tests from Karlsruhe, W. Germany are compared with calculated release fractions and samples taken from TMI Unit-2. It is concluded that very little tellurium was released and transported from the TMI-2 core, probably as a result of holdup by zircaloy cladding and other structural materials. 39 refs., 24 figs., 17 tabs

Development of tellurium oxide and lead-bismuth oxide glasses for mid-wave infra-red transmission optics

Science.gov (United States)

Zhou, Beiming; Rapp, Charles F.; Driver, John K.; Myers, Michael J.; Myers, John D.; Goldstein, Jonathan; Utano, Rich; Gupta, Shantanu

2013-03-01

Heavy metal oxide glasses exhibiting high transmission in the Mid-Wave Infra-Red (MWIR) spectrum are often difficult to manufacture in large sizes with optimized physical and optical properties. In this work, we researched and developed improved tellurium-zinc-barium and lead-bismuth-gallium heavy metal oxide glasses for use in the manufacture of fiber optics, optical components and laser gain materials. Two glass families were investigated, one based upon tellurium and another based on lead-bismuth. Glass compositions were optimized for stability and high transmission in the MWIR. Targeted glass specifications included low hydroxyl concentration, extended MWIR transmission window, and high resistance against devitrification upon heating. Work included the processing of high purity raw materials, melting under controlled dry Redox balanced atmosphere, finning, casting and annealing. Batch melts as large as 4 kilograms were sprue cast into aluminum and stainless steel molds or temperature controlled bronze tube with mechanical bait. Small (100g) test melts were typically processed in-situ in a 5%Au°/95%Pt° crucible. Our group manufactured and evaluated over 100 different experimental heavy metal glass compositions during a two year period. A wide range of glass melting, fining, casting techniques and experimental protocols were employed. MWIR glass applications include remote sensing, directional infrared counter measures, detection of explosives and chemical warfare agents, laser detection tracking and ranging, range gated imaging and spectroscopy. Enhanced long range mid-infrared sensor performance is optimized when operating in the atmospheric windows from ~ 2.0 to 2.4μm, ~ 3.5 to 4.3μm and ~ 4.5 to 5.0μm.

On the resistivity of metal-tellurium alloys for low concentrations of tellurium

International Nuclear Information System (INIS)

Gorecki, J.

1982-04-01

The resistivity and thermoelectric power of metal-tellurium liquid alloys have been discussed for the case of small tellurium concentration. Nearly free electron model of conduction band has been used. The rapid increase of resistivity in transition metal-tellurium alloys has been predicted. (author)

Status of tellurium--hastelloy N studies in molten fluoride salts

International Nuclear Information System (INIS)

Keiser, J.R.

1977-10-01

Tellurium, which is a fission product in nuclear reactor fuels, can embrittle the surface grain boundaries of nickel-base structural materials. This report summarizes results of an experimental investigation conducted to understand the mechanism and to develop a means of controlling this embrittlement in the alloy Hastelloy N. The addition of a chromium telluride to salt can be used to provide small partial pressures of tellurium simulating a reactor environment where tellurium appears as a fission product. The intergranular embrittlement produced in Hastelloy N when exposed to this chromium telluride-salt mixture can be reduced by adding niobium to the Hastelloy N or by controlling the oxidation potential of the salt in the reducing range

Simple and effective method for nuclear tellurium isomers separation from antimony cyclotron targets

International Nuclear Information System (INIS)

Bondarevskij, S.I.; Eremin, V.V.

1999-01-01

Simple and effective method of generation of tellurium nuclear isomers from irradiated on cyclotron metallic antimony is suggested. Basically this method consists in consideration of the big difference in volatilities of metallic forms of antimony, tin and tellurium. Heating of the tin-antimony alloy at 1200 K permits to separate about 90 % of produced quantity of 121m Te and 123m Te (in this case impurity of antimony radionuclides is not more than 1 % on activity) [ru

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis.

Science.gov (United States)

Yang, Fang; Wong, Ka-Hing; Yang, Yufeng; Li, Xiaoling; Jiang, Jie; Zheng, Wenjie; Wu, Hualian; Chen, Tianfeng

2014-01-01

Tellurium-containing phycocyanin (Te-PC) and allophycocyanin (Te-APC), two organic tellurium (Te) species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 μg g(-1) protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropane)dihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress.

Reaction of tellurium with Zircaloy-4

International Nuclear Information System (INIS)

Boer, R. de; Cordfunke, E.H.P.

1994-09-01

Interaction of tellurium vapour with Zircaloy during the initial stage of an accident will lead to retention of tellurium in the core. For reliable estimation of the release behaviour of tellurium, it is necessary to know which zirconium tellurides are formed during this interaction. In this work the reaction of tellurium with Zircaloy-4 has been studied, using various reaction temperatures and tellurium vapour pressures. The compound ZrTe 2-x is formed on the surface of the Zircaloy in a broad range of reaction temperatures and vapour pressures. It is found that the formation of the more zirconium-rich compound Zr 5 Te 4 is favoured at high reaction temperatures is combination with low tellurium vapour pressures. (orig.)

Electrochemical and antimicrobial activity of tellurium oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Gupta, Pramod K. [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Sharma, Prem Prakash; Sharma, Anshu [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Khan, Zishan H., E-mail: zishan_hk@yahoo.co.in [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Solanki, Pratima R., E-mail: pratimarsolanki@gmail.com [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India)

2016-09-15

Highlights: • TeO{sub 2} NPs synthesized without using any catalyst by chemical vapour deposition method. • The growth temperature was 410 °C with continuous flow of O{sub 2.} • TeO{sub 2} NPs have anti-bacterial activity against E. coli, K. pneumoniae and S. aureus while enhances the growth of S. pyogenes. • TeO{sub 2} shows maximum redox current at pH 7 for phosphate buffer solution. - Abstract: Thin film of tellurium oxide (TeO{sub 2}) has been synthesized by chemical vapour deposition method onto indium tin oxide (ITO) coated glass substrate without using any catalyst. XRD pattern of TeO{sub 2} thin film suggests that the structure of TeO{sub 2} changes from amorphous to crystalline (paratellurite) on dispersing into deionized water. Zeta potential measurement reveals a positive surface potential of 28.8 mV. TEM images shows spherical shaped TeO{sub 2} nanoparticles having average particle size of 65 nm. Electrochemical studies of TeO{sub 2}/ITO electrode exhibit improved electron transfer owing to its inherent electron transfer property at pH 7.0 of phosphate buffer. Antimicrobial activity of TeO{sub 2} has been studied for gram-positive (Staphylococcus aureus and Streptococcus pyogenes) and gram negative (Escherichia coli and Klebsiella pneumoniae) bacterial and fungal strains (Aspergillus nizer and Candida albicans). These studies suggest that the TeO{sub 2} NPs inhibit the growth of E. coli, K. pneumoniae and S. aureus bacteria, whereas the same particles enhance the growth of S. pyogenes bacteria.

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis

Directory of Open Access Journals (Sweden)

Yang F

2014-10-01

Full Text Available Fang Yang,1 Ka-Hing Wong,2 Yufeng Yang,3 Xiaoling Li,1 Jie Jiang,1 Wenjie Zheng,1 Hualian Wu,1 Tianfeng Chen1 1Department of Chemistry, Jinan University, Guangzhou, People’s Republic of China; 2Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hong Kong, People’s Republic of China; 3Institute of Hydrobiology, College of Life Science and Technology, Jinan University, Guangzhou, People’s Republic of China Abstract: Tellurium-containing phycocyanin (Te-PC and allophycocyanin (Te-APC, two organic tellurium (Te species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 µg g-1 protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropanedihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress. Keywords: tellurium, phycocyanin, allophycocyanin, purification, antioxidant activity

Double beta decay of tellurium-130

International Nuclear Information System (INIS)

Richardson, J.F.; Manuel, O.K.; Sinha, B.; Thorpe, R.I.

1986-01-01

The isotopic composition of xenon is reported in four, neutron-irradiated tellurium minerals - tellurobismuthite from Boliden, Sweden, native tellurium from the Good Hope Mine of Gunnison County, Colorado, altaite from the Kirkland Lake area, Ontario, and altaite from the Mattagami Lake area, Quebec. From the amount of radiogenic 130 Xe and pile-produced 131 Xe in these samples, it is concluded that the half-life of 130 Te for ββ-decay is 21 y based on measured values of (1.0+-0.3) . 10 21 y and higher. Our results demonstrate that there has been no significant partial leakage of radiogenic 130 Xe from these minerals over geologic time. Larger values of Tsub(1/2), as indicated from some of the analysis reported here and in other studies, are attributed to recrystallization of the soft telluride minerals and complete resetting of the Te-Xe system after mineralization. The value obtained here for the half-life of 130 Te is substantiated by recent measurements on xenon in tellurides from Kalgoorlie, Western Australia. (orig.)

Electrochemical characterization of the underpotential deposition of tellurium on Au electrode

International Nuclear Information System (INIS)

Zhu, W.; Yang, J.Y.; Zhou, D.X.; Bao, S.Q.; Fan, X.A.; Duan, X.K.

2007-01-01

Electrochemical characterization of the underpotential deposition (UPD) of tellurium on Au substrate has been performed in this paper. The mechanism of Te deposition and its voltammetry dependence on the Te ion concentration were studied, and it suggests that variations in the metal ion concentration may affect the UPD process kinetics. The effect of tellurium adsorbates on UPD behavior of Te has also been investigated. The results show that the tellurium adsorbates could be irreversibly adsorbed upon the Au substrate surface under the open-circuit conditions. Subsequent removal of the Te adsorbates was also proved to be very difficult within the Au double-layer region, and a standard electrochemical cleaning procedure is necessary to remove the Te adsorbates completely. When the potential was cycled into the Au oxidation region, a substantial loss of Te adsobates was observed, which occurs simultaneously with the Au oxidation features. Scan rate dependent cyclic voltammetry experiments reveal that the peak current in the Te UPD peak is not a linear function of the scan rate, ν, but of a 2/3 power of the scan rate, ν 2/3 . It is in good consistent with a two-dimension nucleation and growth mechanism

Exploring molecular and spin interactions of Tellurium adatom in reduced graphene oxide

Energy Technology Data Exchange (ETDEWEB)

Alegaonkar, Ashwini [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India); Alegaonkar, Prashant [Department of Applied Physics, Defence Institute of Advance Technology, Girinagar, Pune, 411 025, MS (India); Pardeshi, Satish, E-mail: skpar@chem.unipune.ac.in [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India)

2017-07-01

The transport of spin information fundamentally requires favourable molecular architecture and tunable spin moments to make the medium pertinent for spintronic. We report on achieving coherent molecular-spin parameters for rGO due to Tellurium (Te) adatom. Initially, GO prepared using graphite, was modified into rGO by in situ incorporation of 1 (w/w)% of Te. Both the systems were subjected to ESCA, FTIR, Raman dispersion, ESR spectroscopy, and electron microscopy. Analysis revealed that, Te substantially reacted with epoxides, carbonyl, and carboxylate groups that improved C-to-O ratio by twice. However, the spin splitting character, between Te and C, seems to be quenched. Moreover, Te altered the dynamical force constant between C-C and C=C that generated the mechanical stress within rGO network. The layer conjugation, nature of folding, symmetry, and electronic states of the edges were also affected by precipitation and entrapment of Te. The calculated dynamic molecular Raman and ESR spin parameters indicated that, Te acted as a bridging element for long range spin transport. This is particularly due to, the p-orbital moments of Te contributing, vectorially, to spin relaxation process operative at broken inversion symmetry sites. Our study suggests that, facile addition of Te in rGO is useful to achieve favourable spintronic properties. - Highlights: • Spin interactions and molecular dynamics modification due to Tellurium adatom in rGO. • Molecular level manipulation of Tellurium adatom for favourable spintronic properties. • Bychocov-Rashaba coupling are the operative channels in rGO. • Extrinsic coupling component get added vectorially by Tellurium. • Te-rGO is a viable medium for molecular spintronics.

Electrowinning Of Tellurium From Acidic Solutions

Directory of Open Access Journals (Sweden)

Kowalik R.

2015-06-01

Full Text Available The process of electrochemical deposition of tellurium was studied. Preliminary researches embrace the voltammetry and microgravimetric measurements. According to the results the electrolysis of tellurium was conducted under potentiostatic conditions. There was no deposition of tellurium above potential −0.1 vs. Ag/AgCl electrode in 25°C. The process of deposition is observed in the range of potentials −0.1 to −0.3 V vs. Ag/AgCl. The presence of tellurium was confirmed by XRF and XRD. The obtained deposits were homogenous and compact. Below potential −0.3 V vs. Ag/AgCl the Faradaic efficiency of the tellurium deposition decreased due to reduction of Te to H2Te and hydrogen evolution.

Liquid-liquid extraction of arsenic, antimony, selenium and tellurium by zinc diethyldithiocarbamate

International Nuclear Information System (INIS)

Bajo, S.; Wyttenbach, A.

1978-03-01

The authors report the solvent extraction, oxidation, reduction, extraction in the presence of iron, and reextraction of arsenic, antimony, selenium and tellurium. These processes were studied using radioactive tracers. (G.T.H.)

Thermodynamic behaviour of tellurium at high temperatures

International Nuclear Information System (INIS)

Garisto, F.

1992-09-01

Thermodynamic calculations are used to determine the chemical speciation of tellurium in the primary heat transport system under postulated reactor accident conditions. The speciation of tellurium is determined for various values of the temperature, oxygen partial pressure, tellurium concentration and Cs/Te ratio. The effects of the Zircaloy cladding and/or cesium on tellurium speciation and volatility are of particular interest in this report. (Author) (37 refs., 14 figs., 4 tabs.)

New radiohalogenated alkenyl tellurium fatty acids

International Nuclear Information System (INIS)

Srivastava, P.C.; Knapp, F.F. Jr.; Kabalka, G.W.

1987-01-01

Radiolabeled long-chain fatty acids have diagnostic value as radiopharmaceutical tools in myocardial imaging. Some applications of these fatty acids are limited due to their natural metabolic degradation in vivo with subsequent washout of the radioactivity from the myocardium. The identification of structural features that will increase the myocardial residence time without decreasing the heart uptake of long-chain fatty acids is of interest. Fatty acids containing the tellurium heteroatom were the first modified fatty acids developed that show unique prolonged myocardial retention and low blood levels. Our detailed studies with radioiodinated vinyliodide substituted tellurium fatty acids demonstrate that heart uptake is a function of the tellurium position. New techniques of tellurium and organoborane chemistry have been developed for the synthesis of a variety of radioiodinated iodoalkenyl tellurium fatty acids. 9 refs., 3 figs., 2 tabs

Tellurium in active volcanic environments: Preliminary results

Science.gov (United States)

Milazzo, Silvia; Calabrese, Sergio; D'Alessandro, Walter; Brusca, Lorenzo; Bellomo, Sergio; Parello, Francesco

2014-05-01

Tellurium is a toxic metalloid and, according to the Goldschmidt classification, a chalcophile element. In the last years its commercial importance has considerably increased because of its wide use in solar cells, thermoelectric and electronic devices of the last generation. Despite such large use, scientific knowledge about volcanogenic tellurium is very poor. Few previous authors report result of tellurium concentrations in volcanic plume, among with other trace metals. They recognize this element as volatile, concluding that volcanic gases and sulfur deposits are usually enriched with tellurium. Here, we present some results on tellurium concentrations in volcanic emissions (plume, fumaroles, ash leachates) and in environmental matrices (soils and plants) affected by volcanic emissions and/or deposition. Samples were collected at Etna and Vulcano (Italy), Turrialba (Costa Rica), Miyakejima, Aso, Asama (Japan), Mutnovsky (Kamchatka) at the crater rims by using common filtration techniques for aerosols (polytetrafluoroethylene filters). Filters were both eluted with Millipore water and acid microwave digested, and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). Volcanic ashes emitted during explosive events on Etna and Copahue (Argentina) were analyzed for tellurium bulk composition and after leaching experiments to evaluate the soluble fraction of tellurium. Soils and leaves of vegetation were also sampled close to active volcanic vents (Etna, Vulcano, Nisyros, Nyiragongo, Turrialba, Gorely and Masaya) and investigated for tellurium contents. Preliminary results showed very high enrichments of tellurium in volcanic emissions comparing with other volatile elements like mercury, arsenic, thallium and bismuth. This suggests a primary transport in the volatile phase, probably in gaseous form (as also suggested by recent studies) and/or as soluble salts (halides and/or sulfates) adsorbed on the surface of particulate particles and ashes. First

Tellurium: providing a bright future for solar energy

Science.gov (United States)

Goldfarb, Richard J.

2015-01-01

Tellurium is one of the least common elements on Earth. Most rocks contain an average of about 3 parts per billion tellurium, making it rarer than the rare earth elements and eight times less abundant than gold. Grains of native tellurium appear in rocks as a brittle, silvery-white material, but tellurium more commonly occurs in telluride minerals that include varied quantities of gold, silver, or platinum. Tellurium is a metalloid, meaning it possesses the properties of both metals and nonmetals.

Simultaneous determination of selenium and tellurium in native sulfur by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Arikawa, Yoshiko; Hirai, Shoji; Ozawa, Takejiro.

1979-01-01

A method for the determination of selenium and tellurium in native sulfur has been investigated by means of atomic absorption spectrophotometry. Native sulfur collected from around fumarole or volcanic crater is ground down into powder, a portion of which weighing 1 g is subjected to analysis. A 2.6% (w/v) sodium hydroxide solution is added by 10 ml to the sample in a teflon beaker, and the mixture is then heated on a hot plate. Sulfur is decomposed and dissolved in the form of disulfide and thiosulfate. A 30% hydrogenperoxide solution is added by 10 ml to oxidize them to sulfate. At the same time selenium and tellurium contained in the sulfur sample are also thought to be oxidized to Se(VI) and Te(VI) states. The solution is neutralized with hydrochloric acid and diluted with distilled water to 100 ml. The sample solution thus prepared is sprayed into the air-acetylene flame of the atomic absorption spectrophotometer. The absorbance is measured at 195.9 nm for selenium and 214.2 nm for tellurium. Calibration curve is prepared by measuring the absorbances of the solutions prepared as follows. One gram portions of pure sulfur (99.9999%) are decomposed as for the samples. After neutralization, standard solutions containing each same amount of selenium and tellurium (0 -- 1000 μg) are added to the sulfur solution and then diluted with water to 100 ml. The standard deviations were estimated to be 50.4 ppm for selenium at 756 ppm and 16.6 ppm for tellurium at 587 ppm. For the check of the reliability of the method, results were compared with those obtained by neutron activation analysis. Results obtained by both methods showed good agreement. (author)

Chemical processes for the extreme enrichment of tellurium into marine ferromanganese oxides

Science.gov (United States)

Kashiwabara, Teruhiko; Oishi, Yasuko; Sakaguchi, Aya; Sugiyama, Toshiki; Usui, Akira; Takahashi, Yoshio

2014-04-01

Tellurium, an element of growing economic importance, is extremely enriched in marine ferromanganese oxides. We investigated the mechanism of this enrichment using a combination of spectroscopic analysis and adsorption/coprecipitation experiments. X-ray Absorption Near-Edge Structure (XANES) analysis showed that in adsorption/coprecipitation systems, Te(IV) was oxidized on δ-MnO2 and not oxidized on ferrihydrite. Extended X-ray Absorption Fine Structure (EXAFS) analysis showed that both Te(IV) and Te(VI) were adsorbed on the surface of δ-MnO2 and ferrihydrite via formation of inner-sphere complexes. In addition, Te(VI) can be structurally incorporated into the linkage of Fe octahedra through a coprecipitation process because of its molecular geometry that is similar to the Fe octahedron. The largest distribution coefficient obtained in the adsorption/coprecipitation experiments was for the Te(VI)/ferrihydrite coprecipitation system, and it was comparable to those calculated from the distribution between natural ferromanganese oxides and seawater. Our XAFS and micro-focused X-ray fluorescence (μ-XRF) mapping of natural ferromanganese oxides showed that Te was structurally incorporated as Te(VI) in Fe (oxyhydr)oxide phases. We conclude that the main process for the enrichment of Te in ferromanganese oxides is structural incorporation of Te(VI) into Fe (oxyhydr)oxide phases through coprecipitation. This mechanism can explain the unique degree of enrichment of Te compared with other oxyanions, which are mainly enriched via adsorption on the surface of the solid structures. In particular, the great contrast in the distributions of Te and Se is caused by their oxidized species: (i) the similar geometry of the Te(VI) molecule to Fe octahedron, and (ii) quite soluble nature of Se(VI). Coexisting Mn oxide phases may promote structural incorporation of Te(VI) by oxidation of Te(IV), although the surface oxidation itself may not work as the critical enrichment process as

Extractive separation of tellurium(4)

International Nuclear Information System (INIS)

Gawali, S.B.; Shinde, V.M.

1977-01-01

A method is described for the extraction of tellurium (4) from hydrobromic acid media using 4-methyl-2-pentanol as an extractant. The method affords the determination of tellurium after its separation from Se, Au, Cu, Pb, Fe, Os, V and Al. (author)

Starting material radiation source for Moessbauer investigations of tellurium compounds

International Nuclear Information System (INIS)

Alexandrov, A.J.; Grushko, J.S.; Makarov, E.F.; Mishin, K.Y.; Baltrunas, D.A.J.

1977-01-01

A method is described of preparing a radiation source for Mossbauer investigations of tellurium compounds manufactured on the basis of 5 MgO . Te 124 O 3 . 5 MgO . Te 124 O 3 is irradiated in a reactor by means of thermal neutrons, followed by annealing at a temperature ranging from 600 0 to 1,100 0 C for a period of from 5 to 10 hours

Comparison of analytical possibilities of inversion voltammetry of tellurium with cathodic and anodic potential scanning taking layer-by-layer analysis of GaAs-Te films as example

International Nuclear Information System (INIS)

Kaplin, A.A.; Portnyagina, Eh.O.; Gridaev, V.F.

1979-01-01

Possibility of application in analytical purposes of the process of tellurium precipitation electrosolution from the surfaces of graphite and mercury-graphite electrodes at the cathode scanning of the potential is shown. As a result of comparison of direct and inversion scanning with cathodic and anodic scanning of the potential, variants of voltammetric method of tellurium determination in artificial solutions and, taking the developed method of layer-by-layer analysis of the GaAsTe films as an example, advantage of mercury-graphite electrode with cathodic scanning as compared to graphite electrode with cathode scanning of the potential is shown. Reproducibility of the GaAs film analysis results according to anodic and cathodic tellurium peaks is satisfactory. Maximum deviation from the results of analysis of oxidation peaks and tellurium peduction does not exceed 15 rel. %. Thus, for tellurium concentrations, exceeding 5x10 -6 g-ion/l, both anodic and cathodic scanning of the potential can be used, though error in tellurium determination according to cathodic peaks is 1.5-2.0 times higher. At tellurium amounts lower 5x10 -6 g-ion/l the determination should be carried out according to the peaks of tellurium anodic oxidation from the surface of graphite electrode or according to the peaks of tellurium cathodic reduction from the surface of mercury-graphite electrode

Tellurium self-diffusion and point defects in lead telluride

International Nuclear Information System (INIS)

Simirskij, Yu.N.; Firsova, L.P.

1982-01-01

Method of radioactive indicators was used to determine factors of tellurium self-diffusion in lead telluride with different deviation of the composition from stoichiometric in the range of enrichment by tellurium. It was found that at 973 K factors of tellurium self-diffusion in lead telluride depend slightly on the vapor pressure of tellurium equilibrium with solid phase

Raman and DSC studies of fragility in tellurium-zinc oxide glass formers

International Nuclear Information System (INIS)

Stavrou, Elissaios; Kripotou, Sotiria; Raptis, Constantine; Turrell, Sylvia; Syassen, Karl

2011-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out in four mixed (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses at high temperatures (Raman and DSC through the glass transition) and high pressures (Raman) with the aim of determining the fragility of these glass forming oxides. Four different criteria, corresponding to four parameters, were applied to assess the fragility of the glasses. From the DSC studies, we have obtained the fragility parameter m which corresponds to the slopes of Arrhenius (lnQ vs. 1/T g , were Q is the heating rate) plots, and the glass transition width ΔT g . Also, from the low-frequency Raman scattering, and in particular the boson peak intensity of the glasses at T g , we have estimated the fragility ratio r R (T g ) = I min /I max whose value serves as another (empirical) fragility criterion. Finally, from high pressure Raman measurements on the glasses, we have estimated the Grueneisen parameter γ T for each glass, which constitutes the fourth fragility parameter adopted in this work. Considering the four parameters ΔT g , m, r (T g ) and γ T and the generally accepted (empirical) fragility criteria, we conclude that the mixed tellurium-zinc oxides constitute strong-to-intermediate glass formers (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Fission product tellurium chemistry from fuel to containment

International Nuclear Information System (INIS)

McFarlane, J.

1996-01-01

Chemical equilibrium calculations were performed on the speciation of tellurium in-core and inside the primary heat transport system (PHTS) under loss-of-coolant accident conditions. Data from recent Knudsen-cell experiments on the volatilization of Cs 2 Te were incorporated into the calculation. These data were used to recalculate thermodynamic quantities for Cs 2 Te(g), including Δ f G o (298 K)= -118±9 kJ.mol -1 . The description of the condensed high-temperature cesium-tellurium phase was expanded to include Cs 2 Te 3 (c) in addition to Cs 2 Te(c). These modifications were incorporated into the database used in the equilibrium calculations; the net effect was to stabilize the condensed cesium-tellurium phase and reduce the vapour pressure of Cs 2 Te(g) between 1200 and 1600 K. The impact of tellurium speciation in containment, after release from the PHTS, is discussed along with the possible effect of tellurium on iodine chemistry. (author) 10 figs., 5 tabs., 21 refs

Fission product tellurium chemistry from fuel to containment

Energy Technology Data Exchange (ETDEWEB)

McFarlane, J [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

1996-12-01

Chemical equilibrium calculations were performed on the speciation of tellurium in-core and inside the primary heat transport system (PHTS) under loss-of-coolant accident conditions. Data from recent Knudsen-cell experiments on the volatilization of Cs{sub 2}Te were incorporated into the calculation. These data were used to recalculate thermodynamic quantities for Cs{sub 2}Te(g), including {Delta}{sub f}G{sup o}(298 K)= -118{+-}9 kJ.mol{sup -1}. The description of the condensed high-temperature cesium-tellurium phase was expanded to include Cs{sub 2}Te{sub 3}(c) in addition to Cs{sub 2}Te(c). These modifications were incorporated into the database used in the equilibrium calculations; the net effect was to stabilize the condensed cesium-tellurium phase and reduce the vapour pressure of Cs{sub 2}Te(g) between 1200 and 1600 K. The impact of tellurium speciation in containment, after release from the PHTS, is discussed along with the possible effect of tellurium on iodine chemistry. (author) 10 figs., 5 tabs., 21 refs.

Quantitative analysis of tellurium in simple substance sulfur

International Nuclear Information System (INIS)

Arikawa, Yoshiko

1976-01-01

The MIBK extraction-bismuthiol-2 absorptiometric method for the quantitative analysis of tellurium was studied. The method and its limitation were compared with the atomic absorption method. The period of time required to boil the solution in order to decompose excess hydrogen peroxide and to reduce tellurium from 6 valance to 4 valance was examined. As a result of experiment, the decomposition was fast in the alkaline solution. It takes 30 minutes with alkaline solution and 40 minutes with acid solution to indicate constant absorption. A method of analyzing the sample containing tellurium less than 5 ppm was studied. The experiment revealed that the sample containing a very small amount of tellurium can be analyzed when concentration by extraction is carried out for the sample solutions which are divided into one gram each because it is difficult to treat several grams of the sample at one time. This method also is suitable for the quantitative analysis of selenium. This method showed good addition effect and reproducibility within the relative error of 5%. The comparison between the calibration curve of the standard solution of tellurium 4 subjected to the reaction with bismuthiol-2 and the calibration curve obtained from the extraction of tellurium 4 with MIBK indicated that the extraction is perfect. The result by bismuthiol-2 method and that by atom absorption method coincided quite well on the same sample. (Iwakiri, K.)

Facile electrochemical synthesis of tellurium nanorods and their photoconductive properties

Energy Technology Data Exchange (ETDEWEB)

Li, H.H. [Center for Photon Manufacturing Science and Technology, School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); Zhang, P. [Dongguan University of Technology, Dongguan-523808 (China); School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou - 510275 (China); Liang, C.L. [Instrumental Analysis and Research Center, SunYat-sen University, Guangzhou - 510275 (China); Yang, J. [School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); Zhou, M. [Center for Photon Manufacturing Science and Technology, School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); The State Key Laboratory of Tribology, Tsinghua University, Beijing - 10084 (China); Lu, X.H. [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou - 510275 (China); Hope, G.A. [School of Biomolecular and Physical Sciences, Griffith University, Nathan - Qld 4111 (Australia)

2012-10-15

Tellurium nanorods have been successfully fabricated by template and surfactant-free electrochemical technique from an aqueous solution at room temperature. The as-prepared tellurium nanorods were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectrometry, UV-vis spectroscopy and photoluminescence spectroscopy. Films based on tellurium nanorods were constructed to study the photoresponse and I-V curves. These photoresponse measurements demonstrate that tellurium nanorods exhibited enhanced conductivity under illumination compared to in the dark measurement. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of tellurium thin films electrodeposition from acidic citric bath

Energy Technology Data Exchange (ETDEWEB)

Kowalik, Remigiusz; Kutyła, Dawid [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland); Mech, Krzysztof [AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, al. A. Mickiewicza 30, Krakow (Poland); Żabiński, Piotr, E-mail: rkowalik@agh.edu.pl [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland)

2016-12-01

This work presents the description of the electrochemical process of formation thin tellurium layers from citrate acidic solution. The suggested methodology consists in the preparation of stable acidic baths with high content of tellurium, and with the addition of citrate acid. In order to analyse the mechanism of the process of tellurium deposition, the electroanalytical tests were conducted. The tests of cyclic voltammetry and hydrodynamic ones were performed with the use of polycrystalline gold disk electrode. The range of potentials in which deposition of tellurium in direct four-electron process is possible was determined as well as the reduction of deposited Te° to Te{sup 2−} and its re-deposition as a result of the comproportionation reaction. On the basis of the obtained results, the deposition of tellurium was conducted by the potentiostatic method. The influence of a deposition potential and a concentration of TeO{sub 2} in the solution on the rate of tellurium coatings deposition was examined. The presence of tellurium was confirmed by X-ray spectrofluorometry and electron probe microanalysis. In order to determine the phase composition and the morphology, the obtained coatings were analysed with the use of x-ray diffraction and scanning electron microscopy.

Study of inhibition on lipid oxidation of irradiated pork

International Nuclear Information System (INIS)

Ha Yiming

2006-03-01

It was studied that the effect factors of irradiation dose, preservation temperature, oxygen content and antioxidant on lipid oxidation of irradiated pork. A mechanism was explained on lipid oxidation of irradiated pork. The results showed that irradiation might aggravate lipid oxidation of pork and that decreased preservation temperature and oxygen content of the packaging, added antioxidant also could effectively inhibit lipid oxidation of irradiated pork. (authors)

Properties of low-alloy steel with tellurium

International Nuclear Information System (INIS)

Popova, L.V.; Lebedev, D.V.; Litvinenko, D.A.; Nasibov, A.G.

1983-01-01

The results of investigations into 09G2 and 09G2F steels alloyed with tellurium after controlled rolling are presented. 0.002-0.011% tellurium additions did not change strength and plastic properties of the steels after controlled rolling. Tellurium additions results in 40-50% increase of the steel impact strength on samples With circular and sharp cuts in brittle-viscous region. 0.002-0.003% of tellurium is considered to be the optimum content from the view point of increa=. sing steel strength. Increase of impact strength takes place at the expense of growth of both work function of crack formation and work function of crack propagation but in different temperature ranges: at the expense of firstone at 80-40 deg C, at the expense of second one at 20-40 deg C. 0.002-0.011% teilurium additions mainly at the expense of sulphide globularization bring about decrease of anisotropy of steet properties by impact strength reducing anisotropy factor from 2 to 1.5

Analysis of tellurium-silicon alloys. Part 1. Determination of tellurium by the reduction from perchloric acid solution

International Nuclear Information System (INIS)

Teperek, J.

1977-01-01

When 100-150 mg of tellurium is dissolved in the solution containing 20 cm 3 72 wt.% of perchloric acid, the reduction of tellurium to elementary form is possible only after adding 60-100 milimoles of HCl. The reduction is performed by adding 1 cm 3 of saturated sodium pyrosulphite solution (Na 2 S 2 O 5 ) and 10 cm 3 of 10 wt.% hydrazine hydrochloride solution (N 2 H 4 .2HCl) to 80-90 cm 3 of cold solution of Te in HClO 4 -HCl mixture. The reduction is completed after 3-5 min. of boiling. When 150-200 mg sample of Te-Si alloy is dissolved in 20 cm 3 of hot 72% per chloric acid, the separation of components is reached. Tellurium can be determinated in filtrate by proposed procedure with high accuracy and precision. (author)

Polarographic determination of selenium and tellurium in silver-gold alloys

International Nuclear Information System (INIS)

Gornostaeva, T.D.; Shmargun, S.V.

1986-01-01

The determination of selenium and tellurium is of importance in monitoring the composition of silver-gold alloys (SGA) since these elements are harmful impurities in the pure metals. Tellurium is determined in silver alloys by atomic absorption and atomic emmission methods; selenium determination is made by atomic absorption methods. This paper examines the polarographic determination of silver and tellurium in SGA containing platinum metals and copper. Copper and the bulk of the platinum and palladium were removed by precipitating selenium and tellurium with potassium hypophosphite in the elementary state from 6 M HC1. The results of an analysis of samples of SGA according to the proposed method were compared with the results obtained by the atomic absorption method. the relative deviation in the determination of 0.02-1.0% by weight selenium and tellurium does not exceed 0.12 (n = 5)

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

Energy Technology Data Exchange (ETDEWEB)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of); Shakibaie, Mojtaba [Department of Pharmacognosy and Biotechnology, School of Pharmacy, Pharmaceutics Research Center, Kerman University of Medical Sciences, P.O. Box 76175-493 Kerman (Iran, Islamic Republic of); Rezaie, Sassan [Department of Medical Biotechnology, School of Advanced Medical Technologies, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Shahverdi, Ahmad Reza, E-mail: shahverd@sina.tums.ac.ir [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of)

2012-11-15

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

International Nuclear Information System (INIS)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham; Shakibaie, Mojtaba; Rezaie, Sassan; Shahverdi, Ahmad Reza

2012-01-01

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Determination of tellurium in coal samples by means of graphite furnace atomic absorption spectrometry after coprecipitation with iron(III) hydroxide

Energy Technology Data Exchange (ETDEWEB)

Oda, S.; Arikawa, Y. [Japan Womens University, Tokyo (Japan)

2005-11-01

A simple and accurate method for the determination of tellurium in coal samples was investigated by the combustion of samples under a high pressure of oxygen and coprecipitation with Fe(OH){sub 3}, followed by a measurement by graphite furnace atomic absorption spectrometry (GF-AAS). About 0.5 g of an accurately weighed ground coal sample and 0.5 g of starch were combusted in an oxygen combustion bomb filled with oxygen to 3 MPa and added with 3 ml of water as an absorbing solution. The formed tellurium trioxide TeOs dissolved in water as TeO{sub 4}{sup 2-}, which was in turn reduced to TeO{sub 3}{sup 2-} by heating. After diluting the above-mentioned solution up to about 50 ml with water, Fe(OH){sub 3} is formed upon adding Fe(NO{sub 3}){sub 3} and sodium hydroxide solutions at pH 8-9 and left standing overnight. After dissolving the precipitate by HCl, the solution was diluted to 10 ml with water and the concentration of tellurium was measured by GF-AAS at a wavelength of 214.3 nm. The standard addition method was employed for the determination of tellurium in real coal samples, because those processes for the formation of tellurium(VI) oxide and coprecipitation with Fe(OH)3 were interfered by matrices. For NIST SRM 1632c, the standard coal sample tellurium content of 0.057 {+-} 0.004 mg kg{sup -1} was in good agreement with the information value of 0.05 mg kg{sup -1} with 7% of RSD in five replicate analyses. The tellurium contents in 20 real coal samples given by Center for Coal Utilization, Japan were also determined. The tellurium contents in these samples were scattered over the narrow range between 0.032 and 0.100 mg kg{sup -1}.

A recycling model of the biokinetics of systemic tellurium.

Science.gov (United States)

Giussani, Augusto

2014-11-01

To develop a compartmental model of the systemic biokinetics of tellurium required for calculating the internal dose and interpreting bioassay measurements after incorporation of radioactive tellurium. The compartmental model for tellurium was developed with the software SAAM II v. 2.0 (©The Epsilon Group, Charlottesville, Virginia, USA). Model parameters were determined on the basis of published retention and excretion data in humans and animals. The model consists of two blood compartments, one compartment each for liver, kidneys, thyroid, four compartments for bone tissues and a generic compartment for the soft tissues. The model predicts a rapid urinary excretion of systemic tellurium: 45% in the first 24 h and 84% after 50 d. Faecal excretion amounts to 0.4% after 3 d and 9% after 50 d. Whole body retention is 55% after one day, and 2.8% after 100 d. These values as well as the retained fractions in the single organs are reasonably consistent with the available human and animal data (studies with swine and guinea pigs). The proposed model gives a realistic description of the available biokinetic data for tellurium and will be adopted by the International Commission on Radiological Protection for applications in internal dosimetry.

Atomic absorption determination of ultratrace tellurium in rocks utilizing high sensitivity sampling systems

International Nuclear Information System (INIS)

Beaty, R.D.

1973-01-01

The sampling boat and the graphite furnace were shown to possess the required sensitivity to detect tellurium at ultratrace levels, in a variety of sample types, by atomic absorption. In the sampling boat approach, tellurium in sample solutions is chemically separated and concentrated by extraction into methyl isobutyl ketone before measurement. For samples exhibiting extraction interferences or excessively high background absorption, a preliminary separation of tellurium by coprecipitation with selenium is described. Using this technique, tellurium can be quantitatively detected down to 5 nanograms and linear response is observed to 100 nanograms. Relative standard deviations of better than 7 percent are achieved for 50 nanograms of tellurium. For samples that have a tellurium content below the detection limits of the sampling boat, the graphite furnace is used for atomization. By this method, as little as 0.07 nanograms of tellurium can be detected, and a precision of 1 percent relative standard deviation is achievable at the 5 nanogram level. A routinely applicable procedure was developed for determining tellurium in rocks, using the graphite furnace, after a hydrofluoric acid decomposition of the sample. Using this procedure, tellurium data were obtained on 20 different rocks, and the significance of this new information is discussed. (Diss. Abstr. Int., B)

METHODS OF SYNTHESIS EIGHT-TELLURIUM-CONTAINING HETEROCYCLES WITH MORE HETEROATOMS

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2013-01-01

Full Text Available In this article systematized and summarized data on the synthesis of neweight-embered tellurium-containing heterocycles and new preparative methods described above produce heterocyclic tellurium.

Inclusion free cadmium zinc tellurium and cadmium tellurium crystals and associated growth method

Science.gov (United States)

Bolotnikov, Aleskey E [South Setauket, NY; James, Ralph B [Ridge, NY

2010-07-20

The present disclosure provides systems and methods for crystal growth of cadmium zinc tellurium (CZT) and cadmium tellurium (CdTe) crystals with an inverted growth reactor chamber. The inverted growth reactor chamber enables growth of single, large, high purity CZT and CdTe crystals that can be used, for example, in X-ray and gamma detection, substrates for infrared detectors, or the like. The inverted growth reactor chamber enables reductions in the presence of Te inclusions, which are recognized as an important limiting factor in using CZT or CdTe as radiation detectors. The inverted growth reactor chamber can be utilized with existing crystal growth techniques such as the Bridgman crystal growth mechanism and the like. In an exemplary embodiment, the inverted growth reactor chamber is a U-shaped ampoule.

Study of the mechanisms controlling the oxide growth under irradiation: characterization of irradiated zircaloy-4 and Zr-1 Nb-O oxide scales

International Nuclear Information System (INIS)

Bossis, Ph.; Thomazet, J.; Lefebvre, F.

2002-01-01

In PWRs, the Zr-1Nb-O alloy shows a marked enhancement in corrosion resistance in comparison with Zircaloy-4. The aim of this work is to analyze the reasons for these different behaviors and to determine the respective nature of the oxide growth controlling mechanisms under irradiation. Samples taken from Zircaloy-4 irradiated 1, 2, and 4 cycles and Zr-1Nb-O irradiated 1 and 3 cycles have been systematically characterized by optical microscopy, SEM coupled with image analysis, hydride distribution, and XRD. Specific TEM characterizations have been performed on the Zr-1Nb-O samples. A XPS analysis of a nonirradiated sample is also reported. It has been shown that under irradiation the slow oxidation kinetics of the Zr-1Nb-O alloy is associated with very regular metal-oxide interface and oxide layer. On the contrary, the accelerated oxidation kinetics of Zircaloy-4 is associated with highly perturbed metal-oxide interface and oxide layer. On both irradiated alloys, cracks are observed to initiate preferentially above the delayed parts of the oxidation front. Hydrogen intake during water oxidation in PWR environment is found to be much lower on the Zr-1Nb-O alloy than on Zircaloy-4. More β-ZrO 2 is found on the oxide layer formed on Zircaloy-4 than on Zr-1NbO after oxidation in PWR. Classical irradiation-induced microstructural evolution is observed in the Zr-1Nb-O metallic alloy after 3 cycles, i.e., a fine β-Nb precipitation. β-Nb precipitates are observed to undergo a delayed oxidation associated with a crystalline to amorphous transformation. After water oxidation in autoclave, a pronounced Nb segregation is detected on the oxide surface of a Zr-1Nb-O sample. These results suggest that the oxidation kinetics of Zircaloy-4 is controlled essentially by oxygen diffusion through the inner barrier layer, which is significantly accelerated under irradiation. The oxidation kinetics of Zr-1Nb-O is controlled by both oxygen diffusion through the inner barrier and by

Selenium and tellurium reagents in organic synthesis

International Nuclear Information System (INIS)

Comasseto, J.V.

1984-01-01

A review of the contribution of the University of Sao Paulo (SP, Brazil) to the organic synthesis of selenium and tellurium reagents is made. Major reactions amoung selenium compounds and insaturated substrates, phosphorus, ester enolates as well as the use of phase transference catalysed reactions to produce arylselenolate are described. For tellurium, interactions of its compounds with organic substrates and reactive intermediates (e.g. benzino diazomethane) are reported. (C.L.B.) [pt

Rapid radiochemical ion-exchange separation of iodine from tellurium: a novel radioiodine-132 generator

Energy Technology Data Exchange (ETDEWEB)

Abrao, A

1975-01-01

Tellurium ions form a soluble cationic complex with thiourea in acid medium. The cationic tellurium-thiourea species is strongly absorbed on a cationic ion exchanger. The retention of tellurium on the resin enables many interesting separation schemes for tellurium from various ions. With special interest, the separation of iodine from tellurium was studied. An efficient and convenient iodine-132 generator is described, in which the radio-iodine is eluted with water or 9 g/1 NaCl, when desired.

Electrophilic addition of selenium and tellurium halides to methyldiethynylsilane

International Nuclear Information System (INIS)

Amosova, S.V.; Penzik, M.V.; Martynov, A.V.; Zhilitskaya, L.V.; Voronkov, M.G.

2009-01-01

Reaction of TeCl 4 with methyldiethynylsilane (MDES) proceeds with the predominant formation of E-isomer 1,1,3,6-tetrachlorine-1-methyl-1-(methyldiethynylsiloxy)-1,4-tellurium(IV) silafulvic due to the interaction of intermediate E-isomer 4-methyl-1,1,3,6-tetrachlorine-1,4-tellurium(IV)silafulvic with MDES. TeCl 4 Reacts with MDES without reduction of Te(IV) in Te(II). Tetracoordination of tellurium atom in heterocycle was established by NMR 125 Te. Mass spectrum of heterocycle shows the presence of fragmentary ions [M-Cl 2 ] + . According elemental analysis Te:Cl=1:4 ratio proves composition of heterocycle

Electron trapping during irradiation in reoxidized nitrided oxide

International Nuclear Information System (INIS)

Mallik, A.; Vasi, J.; Chandorkar, A.N.

1993-01-01

Isochronal detrapping experiments have been performed following irradiation under different gate biases in reoxidized nitrided oxide (RNO) MOS capacitors. These show electron trapping by the nitridation-induced electron traps at low oxide fields during irradiation. A difference in the detrapping behavior of trapped holes and electrons is observed, with trapped holes being detrapped at relatively lower temperatures compared to trapped electrons. Electron trapping shows a strong dependence on tile magnitude of the applied gate bias during irradiation but is independent of its polarity. Conventional oxide devices, as expected, do not show any electron trapping during irradiation by the native electron traps. Finally, a comparison of the isochronal detrapping behavior following irradiation and following avalanche injection of electrons has been made to estimate the extent of electron trapping. The results show that electron trapping by the nitridation-induced electron traps does not play the dominant role in improving radiation performance of RNO, though its contribution cannot be completely neglected for low oxide field irradiations

Deposition of tellurium films by decomposition of electrochemically-generated H{sub 2}Te: application to radiative cooling devices

Energy Technology Data Exchange (ETDEWEB)

Engelhard, T.; Jones, E.D.; Viney, I. [Coventry Univ. (United Kingdom). Centre for Data Storage Mater.; Mastai, Y.; Hodes, G. [Department of Materials and Interfaces, Weizmann Institute of Science, 76100, Rehovot (Israel)

2000-07-17

The preparation of homogenous, large area thin layers of tellurium on thin polyethylene foils is described. The tellurium was formed by room temperature decomposition of electrochemically generated H{sub 2}Te. Pre-treatment of the polyethylene substrates with KMnO{sub 4} to give a Mn-oxide layer was found to improve the Te adhesion and homogeneity. Optical characterization of the layers was performed using UV/VIS/NIR spectroscopy. Such coatings have favorable characteristics for use as solar radiation shields in radiative cooling devices. The simplicity of generation of the very unstable H{sub 2}Te was also exploited to demonstrate formation of size-quantized CdTe nanocrystals. (orig.)

A rapid radiochemical ion-exchange separation of iodine from tellurium: a novel radioiodine-132 generator

International Nuclear Information System (INIS)

Abrao, A.

1975-01-01

Tellurium ions form a soluble cationic complex with thiourea in acid medium. The cationic tellurium-thiourea species is strongly absorbed on a cationic ion exchanger. The retention of tellurium on the resin enables many interesting separation schemes for tellurium from various ions. With special interest, the separation of iodine from tellurium was studied. An efficient and convenient iodine-132 generator is described, in which the radio-iodine is eluted with water or 9 g/1 NaCL, when desired

Study of distribution coefficients of admixtures in tellurium

International Nuclear Information System (INIS)

Kuchar, L.; Drapala, J.; Kuchar, L. jr.

1986-01-01

Limit areas of tellurium-admixture binary systems were studied and the values determined of steady-state distribution coefficients of admixtures. A second order polynomial was used to express equations of solidus and liquidus curves for Te-Se, Te-S, Te-Hg systems; the curves are graphically represented. The most effective method for preparing high-purity tellurium is zonal melting with material removal. (M.D.). 4 figs., 4 tabs., 16 refs

Effects of tellurium concentration on the structure of melt-grown ZnSe crystals

International Nuclear Information System (INIS)

Atroshchenko, Lyubov V.; Galkin, Sergey N.; Rybalka, Irina A.; Voronkin, Evgeniy F.; Lalayants, Alexandr I.; Ryzhikov, Vladimir D.; Fedorov, Alexandr G.

2005-01-01

It has been shown that isovalent doping by tellurium positively affects the structural perfection of ZnSe crystals related to the completeness of the wurtzite-sphalerite phase transition. The optimum concentration range of tellurium in ZnSe crystals is 0.3-0.6 mass %. X-ray diffraction studies have shown that in ZnSe 1-x Te x crystals at tellurium concentrations below 0.3 mass % twinning and packing defects occur, while tellurium concentrations above 0.6 mass % lead to formation of tetragonal crystal lattice

Improvement of physical properties of ZnO thin films by tellurium doping

Energy Technology Data Exchange (ETDEWEB)

Sönmezoğlu, Savaş, E-mail: svssonmezoglu@kmu.edu.tr; Akman, Erdi

2014-11-01

Highlights: • We report the synthesis of tellurium-doped zinc oxide (Te–ZnO) thin films using sol–gel method. • Highly c-axis oriented Te-doped ZnO thin films were grown on FTO glasses as substrate. • 1.5% Te-doping ratio could improve the physical properties of ZnO thin films. - Abstract: This investigation addressed the structural, optical and morphological properties of tellurium incorporated zinc oxide (Te–ZnO) thin films. The obtained results indicated that Te-doped ZnO thin films exhibit an enhancement of band gap energy and crystallinity compared with non-doped films. The optical transmission spectra revealed a shift in the absorption edge toward lower wavelengths. X-ray diffraction measurement demonstrated that the film was crystallized in the hexagonal (wurtzite) phase and presented a preferential orientation along the c-axis. The XRD obtained patterns indicate that the crystallite size of the thin films, ranging from 23.9 to 49.1 nm, changed with the Te doping level. The scanning electron microscopy and atomic force microscopy results demonstrated that the grain size and surface roughness of the thin films increased as the Te concentration increased. Most significantly, we demonstrate that it is possible to control the structural, optical and morphological properties of ZnO thin films with the isoelectronic Te-incorporation level.

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2003-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122 Te, 124 Te, 125 Te, 126 Te, 128 Te, and 130 Te are reported. These values are based on a combination of newly determined partial γ-ray cross sections obtained from experiments on targets contained natural Te and γ intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

Energy Technology Data Exchange (ETDEWEB)

Tomandl, I.; Honzatko, J.; von Egidy, T.; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-03-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given.

Reduction of Graphene Oxide to Graphene by Using Gamma Irradiation

International Nuclear Information System (INIS)

Shamellia Sharin; Irman Abdul Rahman; Ainee Fatimah Ahmad

2015-01-01

This research aims to gauge the ability of gamma radiation to induce the reduction of graphene oxide to graphene. Graphene oxide powders were dispersed into a mixture of alcohol and deionized water, and the mixture was then irradiated with a "6"0Co source using a GammaCell 220 Excel irradiator at absorbed doses of 0, 5, 15, 20 and 35 kGy. According to characterization using Fourier Transformed Infrared Spectroscopy (FTIR), it can be seen that almost every oxygen-containing functional group has been removed after irradiation of the graphene oxide mixture. Reduction of graphene oxide was also proven from the characterization using UV-Vis Spectroscopy, in which the wavelength of graphene oxide at 237 nm was red-shifted to 277 nm after being irradiated and the peak at 292 nm, (indicating the carboxyl group) disappears in the UV-Vis spectrum of reduced graphene oxide. Morphology of graphene oxide also changed from a smooth and flat surface to crumpled. The ratio of carbon/ oxygen in the graphene oxide was lower than the carbon/ oxygen of reduced graphene oxide. At the end of the experiment, it can be deduced that graphene oxide underwent reduction, characterized before and after irradiation using Emission Scanned Electron Microscopy and Energy Dispersive X-ray, Fourier Transformed Infrared Spectroscopy and UV-Vis Spectroscopy. Therefore, we postulate that the irradiation technique that induces reduction, can be used to obtain reduced graphene oxide from graphene oxide. (author)

Thermodynamic assessment of the palladium-tellurium (Pd-Te) system

International Nuclear Information System (INIS)

Gosse, S.; Gueneau, C.

2011-01-01

Among the fission products formed in nuclear fuels, the platinum-group metal palladium and the chalcogen element tellurium exhibit strong interaction. It is therefore of interest to be able to predict the chemical equilibria involving the Pd and Te fission products. A thermodynamic assessment is carried out using the Calphad (Calculation of Phase Diagram) method to investigate the behaviour of Pd-Te alloy system in nuclear fuels under irradiation and under waste disposal conditions. The Pd-Te binary description was optimized using experimental data found in literature including thermodynamic properties and phase diagram data. To validate the calculated phase diagram and thermodynamic properties, the results are compared with data from the literature. Both calculated and experimental phase diagrams and thermodynamic properties are in good agreement in the whole Pd-Te composition range. (authors)

Van der Waals epitaxy and photoresponse of hexagonal tellurium nanoplates on flexible mica sheets.

Science.gov (United States)

Wang, Qisheng; Safdar, Muhammad; Xu, Kai; Mirza, Misbah; Wang, Zhenxing; He, Jun

2014-07-22

Van der Waals epitaxy (vdWE) is of great interest due to its extensive applications in the synthesis of ultrathin two-dimensional (2D) layered materials. However, vdWE of nonlayered functional materials is still not very well documented. Here, although tellurium has a strong tendency to grow into one-dimensional nanoarchitecture due to its chain-like structure, we successfully realize 2D hexagonal tellurium nanoplates on flexible mica sheets via vdWE. Chemically inert mica surface is found to be crucial for the lateral growth of hexagonal tellurium nanoplates since it (1) facilitates the migration of tellurium adatoms along mica surface and (2) allows a large lattice mismatch. Furthermore, 2D tellurium hexagonal nanoplates-based photodetectors are in situ fabricated on flexible mica sheets. Efficient photoresponse is obtained even after bending the device for 100 times, indicating 2D tellurium hexagonal nanoplates-based photodetectors on mica sheets have a great application potential in flexible and wearable optoelectronic devices. We believe the fundamental understanding of vdWE effect on the growth of 2D tellurium hexagonal nanoplate can pave the way toward leveraging vdWE as a useful channel to realize the 2D geometry of other nonlayered materials.

HT oxidation activity of soil irradiated with gamma radiation

International Nuclear Information System (INIS)

Momoshima, Noriyuki; Tjahaja, P.I.; Takashima, Yoshimasa

1992-01-01

The HT oxidation activity was examined for soils irradiated with 60 Co γ-rays at various doses. The HT oxidation rate decreased with increase of initial H 2 concentration, indicating a similar oxidation mechanism between HT and H 2 . Irradiated soils showed decrease of oxidation activity with dose suggests that HT and H 2 oxidation activities were affected by sterilization with γ-rays. The decline of the oxidation activity with dose was analyzed by a composite of two components with different radiosensitivity and they were considered to be activities of soil microorganisms and abiotic soil enzymes. The oxidation activity due to soil microorganisms would be important at low dose range and more radioresistant abiotic soil enzymes would be responsible for the oxidation activity observed at more than several kGy. In non-irradiated soil about half of the oxidation activity was considered resulting from abiotic soil enzymes. (author)

Volatile profile, lipid oxidation and protein oxidation of irradiated ready-to-eat cured turkey meat products

International Nuclear Information System (INIS)

Feng, Xi; Ahn, Dong Uk

2016-01-01

Irradiation had little effects on the thiobarbituric acid reactive substances (TBARS) values in ready-to-eat (RTE) turkey meat products, while it increased protein oxidation at 4.5 kGy. The volatile profile analyses indicated that the amount of sulfur compounds increased linearly as doses increased in RTE turkey meat products. By correlation analysis, a positive correlation was found between benzene/ benzene derivatives and alcohols with lipid oxidation, while aldehydes, ketones and alkane, alkenes and alkynes were positively correlated with protein oxidation. Principle component analysis showed that irradiated meat samples can be discriminated by two categories of volatile compounds: Strecker degradation products and radiolytic degradation products. The cluster analysis of volatile data demonstrated that low-dose irradiation had minor effects on the volatile profile of turkey sausages (<1.5 kGy). However, as the doses increased, the differences between the irradiated and non-irradiated cured turkey products became significant. - Highlights: • Irradiation had little effects on lipid oxidation of ready-to-eat cured turkey. • 4.5 kGy irradiation increased protein oxidation. • Irradiated samples were isolated due to Strecker/radiolytic degradation products. • 1.5 kGy irradiation had limited effects on the volatile profile of turkey sausages. • Dimethyl disulfide can be used as a potential marker for irradiated meat products.

Comparison between selenium and tellurium clusters

International Nuclear Information System (INIS)

Benamar, A.; Rayane, D.; Tribollet, B.; Broyer, M.; Melinon, P.

1991-01-01

Selenium and tellurium clusters are produced by the inert gas condensation technique. The mass spectra of both species are completely different and reveal different properties. In selenium, a periodicity of 6-7 is observed and may be interpreted by the binding energy between small cyclic molecules. Moreover, it was very difficult to obtained large clusters probably because the binding energy between these molecules is very small. In tellurium, these periodic structures do not exist and large clusters are easily obtained in nucleation conditions where only small selenium clusters are present. These results are discussed and a simple nucleation model is used to illustrate this different behavior. Finally these clusters properties are correlated to the bulk structure of both materials. (orig.)

Electrodeposition of antimony, tellurium and their alloys from molten acetamide mixtures

NARCIS (Netherlands)

Nguyen, H.P.; Peng, X.; Murugan, G.; Vullers, R.J.M.; Vereecken, P.M.; Fransaer, J.

2013-01-01

We examine the electrodeposition of antimony (Sb), tellurium (Te) and their alloys from molten mixtures of acetamide - antimony chloride and tellurium chloride. The binary mixtures of acetamide with SbCl3 and TeCl 4 exhibit eutectic formation with large depressions of freezing points to below room

Oxidative stability examination of irradiated swine for samples

International Nuclear Information System (INIS)

Formanek, Z.

1995-01-01

DSC (Differential Scanning Calorimetry), OBM (Oxygen Bomb Method) methods and POV (Peroxide Value) determination was applied to determine the oxidative stability of lard samples irradiated by a Co 60 gamma source at the dose of 0; 0.75; 2.5kGy. Both of the methods seem to be suitable to determine oxidative stability of fats, because in every case lowering oxidative stability was received with increasing irradiation dose. (R.P.). 8 refs., 7 figs., 1 tab

Time series analysis of blood oxidative stress value in irradiated rats

International Nuclear Information System (INIS)

Kaneko, Takashi; Goto, Jun; Nomiya, Takuma; Nemoto, Kenji

2011-01-01

Indirect effect of ionizing-radiation causes free radicals and reactive oxgen species (ROS). These ROS interact with DNA or other organella, and cause oxidative damage to nucleic acids, membrane lipoprotein, mitchondria and others. The purpose of this study is to evaluate oxidative damage by irradiation using d-ROMs test. Electron beam was irradiated to the thigh of Wistar strain female rats, and reactive oxygen metabolites in the blood from these rats were measured and analysed. From the results, 2 Gy group shows significantly higher oxidative stress level than those of 0 Gy group especially in day 3 after irradiation. This oxidative stress definitely seemed to be caused by exposure to ionizing-radiation. In contrast, the group of 30 Gy-irradiation showed no significant increase of oxidative stress level. It was thought that oxidative stress caused by radiation was neutralized by expression of stress-induced antioxidant enzymes. These data resulted that d-ROMs test is useful for measuring oxidative stress levels of irradiated mammalian animals. (author)

On the study of proton-irradiated Tellurium targets relevant for production of medical radioisotopes 123I and 124I

International Nuclear Information System (INIS)

Imam Kambali; Hari Suryanto; Daya Agung Sarwono; Cahyana Amiruddin

2014-01-01

The energy loss distribution and range of energetic proton beams in tellurium (Te) target have been simulated using the Stopping and Range of Ion in Matter (SRIM 2013) codes. The calculated data of the proton's range were then used to determine the optimum thickness of Te targets for future production of 123 I and 124 I from 123 Te(p,n) 123 I, 124 Te(p,n) 124 I and 124 Te(p,2n) 123 I nuclear reactions using the BATAN's Cs-30 cyclotron. It was found that for an incidence angle of 0° with respect to the target normal, the optimum thickness of 123 Te and 124 Te targets for 123 I production should be 644 µm and 1.8 mm respectively, whereas a 649 µm thick 124 Te target would be Required for 124 I production. In addition, the thickness should be decreased with increasing incidence angle. The EOB yield could theoretically reach up to 13.62 Ci of 123 I at proton energy of 22 Me V and beam current of 30 µA if the 124 Te is irradiated over a period of 3 hours. The theoretical EOB yield is comparable to the experimental data with accuracy within 10%. (author)

DETECTION OF THE SECOND r-PROCESS PEAK ELEMENT TELLURIUM IN METAL-POOR STARS ,

International Nuclear Information System (INIS)

Roederer, Ian U.; Lawler, James E.; Cowan, John J.; Beers, Timothy C.; Frebel, Anna; Ivans, Inese I.; Schatz, Hendrik; Sobeck, Jennifer S.; Sneden, Christopher

2012-01-01

Using near-ultraviolet spectra obtained with the Space Telescope Imaging Spectrograph on board the Hubble Space Telescope, we detect neutral tellurium in three metal-poor stars enriched by products of r-process nucleosynthesis, BD +17 3248, HD 108317, and HD 128279. Tellurium (Te, Z = 52) is found at the second r-process peak (A ≈ 130) associated with the N = 82 neutron shell closure, and it has not been detected previously in Galactic halo stars. The derived tellurium abundances match the scaled solar system r-process distribution within the uncertainties, confirming the predicted second peak r-process residuals. These results suggest that tellurium is predominantly produced in the main component of the r-process, along with the rare earth elements.

Enhanced low-temperature oxidation of zirconium alloys under irradiation

International Nuclear Information System (INIS)

Cox, B.; Fidleris, V.

1989-01-01

The linear growth of relatively thick (>300 nm) interference-colored oxide films on zirconium alloy specimens exposed in the Advanced Test Reactor (ATR) coolant at ≤55 o C was unexpected. Initial ideas were that this was a photoconduction effect. Experiments to study photoconduction in thin anodic zirconium oxide (ZrO 2 ) films in the laboratory were initiated to provide background data. It was found that, in the laboratory, provided a high electric field was maintained across the oxide during ultraviolet (UV) irradiation, enhanced growth of oxide occurred in the irradiated area. Similarly enhanced growth could be obtained on thin thermally formed oxide films that were immersed in an electrolyte with a high electric field superimposed. This enhanced growth was found to be caused by the development of porosity in the barrier oxide layer by an enhanced local dissolution and reprecipitation process during UV irradiation. Similar porosity was observed in the oxide films on the ATR specimens. Since it is not thought that a high electric field could have been present in this instance, localized dissolution of fast-neutron primary recoil tracks may be the operative mechanism. In all instances, the specimens attempt to maintain the normal barrier-layer oxide thickness, which causes the additional oxide growth. Similar mechanisms may have operated during the formation of thick loosely adherent, porous oxides in homogeneous reactor solutions under irradiation, and may be the cause of enhanced oxidation of zirconium alloys in high-temperature water-cooled reactors in some water chemistries. (author)

Development of examination technique for oxide layer thickness measurement of irradiated fuel rods

International Nuclear Information System (INIS)

Koo, D. S.; Park, S. W.; Kim, J. H.; Seo, H. S.; Min, D. K.; Kim, E. K.; Chun, Y. B.; Bang, K. S.

1999-06-01

Technique for oxide layer thickness measurement of irradiated fuel rods was developed to measure oxide layer thickness and study characteristic of fuel rods. Oxide layer thickness of irradiated fuels were measured, analyzed. Outer oxide layer thickness of 3 cycle-irradiated fuel rods were 20 - 30 μm, inner oxide layer thickness 0 - 10 μm and inner oxide layer thickness on cracked cladding about 30 μm. Oxide layer thickness of 4 cycle-irradiated fuel rods were about 2 times as thick as those of 1 cycle-irradiated fuel rods. Oxide layer on lower region of irradiated fuel rods was thin and oxide layer from lower region to upper region indicated gradual increase in thickness. Oxide layer thickness from 2500 to 3000 mm showed maximum and oxide layer thickness from 3000 to top region of irradiated fuel rods showed decreasing trend. Inner oxide layer thicknesses of 4 cycle-irradiated fuel rod were about 8 μm at 750 - 3500 mm from the bottom end of fuel rod. Outer oxide layer thickness were about 8 μm at 750 - 1000 mm from the bottom end of fuel rod. These indicated gradual increase up to upper region from the bottom end of fuel rod. These indicated gradual increase up to upper region from the bottom end of fuel. Oxide layer thickness technique will apply safety evaluation and study of reactor fuels. (author). 6 refs., 14 figs

Intergranular tellurium cracking of nickel-based alloys in molten Li, Be, Th, U/F salt mixture

Science.gov (United States)

Ignatiev, Victor; Surenkov, Alexander; Gnidoy, Ivan; Kulakov, Alexander; Uglov, Vadim; Vasiliev, Alexander; Presniakov, Mikhail

2013-09-01

In Russia, R&D on Molten Salt Reactor (MSR) are concentrated now on fast/intermediate spectrum concepts which were recognized as long term alternative to solid fueled fast reactors due to their attractive features: strong negative feedback coefficients, easy in-service inspection, and simplified fuel cycle. For high-temperature MSR corrosion of the metallic container alloy in primary circuit is the primary concern. Key problem receiving current attention include surface fissures in Ni-based alloys probably arising from fission product tellurium attack. This paper summarizes results of corrosion tests conducted recently to study effect of oxidation state in selected fuel salt on tellurium attack and to develop means of controlling tellurium cracking in the special Ni-based alloys recently developed for molten salt actinide recycler and tranforming (MOSART) system. Tellurium corrosion of Ni-based alloys was tested at temperatures up to 750 °C in stressed and unloaded conditions in molten LiF-BeF2 salt mixture fueled by about 20 mol% of ThF4 and 2 mol% of UF4 at different [U(IV)]/[U(III)] ratios: 0.7, 4, 20, 100 and 500. Following Ni-based alloys (in mass%): HN80М-VI (Mo—12, Cr—7.6, Nb—1.5), HN80МТY (Mo—13, Cr—6.8, Al—1.1, Ti—0.9), HN80МТW (Mo—9.4, Cr—7.0, Ti—1.7, W—5.5) and ЕМ-721 (W—25.2, Cr—5.7, Ti—0.17) were used for the study in the corrosion facility. If the redox state the fuel salt is characterized by uranium ratio [U(IV)]/[U(III)] uranium intermetallic compounds and alloys with nickel and molybdenum. This leads to spontaneous behavior of alloy formation processes on the specimens' surface and further diffusion of uranium deep into the metallic phase. As consequence of this films of intermetallic compounds and alloys of nickel, molybdenum, tungsten with uranium are formed on the alloys specimens' surface, and intergranular corrosion does not take place. In the fuel salt with [U(IV)]/[U(III)] = 4-20 the potentials of uranium

Review of tellurium release rates from LWR fuel elements under accident conditions

International Nuclear Information System (INIS)

Lorenz, R.A.; Beahm, E.C.; Wichner, R.P.

1983-01-01

Although fission product tellurium presents a potentially significant radiohazard, its release and transport in source-term experiments is frequently overlooked because it does not possess a readily measurable, gamma emission; moreover, a recent study emphasized noble gas, iodine and cesium release from LWR fuel elements because of the large data base that exists for these materials. Some new tests show that in some cases tellurium may be held up in core material to a greater degree than previously assumed - an observation that prompts a careful reappraisal of the existing tellurium-release data and its chemical foundation

Relationship between measurements of blood oxidative metabolites and skin reaction in irradiated rats

International Nuclear Information System (INIS)

Kaneko, Takashi; Goto, Jun; Nomiya, Takuma; Nemoto, Kenji

2011-01-01

Recently, oxidative metabolites have been able to be measured by simple small device. It has been reported that the value of oxidative metabolites increases under several conditions such as hypertension, smoking, diabetes mellitus, etc. Radiation used in radiotherapy also causes free radicals and oxidative metabolites, and irradiation causes dermatitis and sometimes causes skin ulcer in the irradiated site. We analyzed the relationships between the value of oxidative metabolites and skin reactions. A certain doses of radiation were irradiated to the right thigh of rats, and oxidative metabolites of rat's blood from caudal vein were measured by d-reactive oxygen metabolites (ROMs) test using an exclusive device. Skin reactions were evaluated according to a skin-reaction grading system from the day before irradiation to day 38 after irradiation. As a results, a significant correlation was shown between irradiation dose and skin grade. And a significant correlation was also shown between the value of oxidative metabolites and irradiation dose. The increase in oxidative metabolites was seen in the Day 16 after irradiation, and that corresponded with the appearance of skin reaction. It was suggested that the value of oxidative metabolites seems to be useful for estimating degree of skin reaction and time to appear skin reaction after irradiation. (author)

Optimization of scintillator loading with the tellurium-130 isotope for long-term stability

Science.gov (United States)

Duhamel, Lauren; Song, Xiaoya; Goutnik, Michael; Kaptanoglu, Tanner; Klein, Joshua; SNO+ Collaboration

2017-09-01

Tellurium-130 was selected as the isotope for the SNO + neutrinoless double beta decay search, as 130Te decays to 130Xe via double beta decay. Linear alkyl benzene(LAB) is the liquid scintillator for the SNO + experiment. To load tellurium into scintillator, it is combined with 1,2-butanediol to form an organometallic complex, commonly called tellurium butanediol (TeBD). This study focuses on maximizing the percentage of tellurium loaded into scintillator and evaluates the complex's long-term stability. Studies on the effect of nucleation due to imperfections in the detector's surface and external particulates were employed by filtration and induced nucleation. The impact of water on the stability of TeBD complex was evaluated by liquid-nitrogen sparging, variability in pH and induced humidity. Alternative loading methods were evaluated, including the addition of stability-inducing organic compounds. Samples of tellurium-loaded scintillator were synthesized, treated, and consistently monitored in a controlled environment. It was found that the hydronium ions cause precipitation in the loaded scintillator, demonstrating that water has a detrimental effect on long-term stability. Optimization of loaded scintillator stability can contribute to the SNO + double beta decay search.

Phase stability of oxide dispersion-strengthened ferritic steels in neutron irradiation

International Nuclear Information System (INIS)

Yamashita, S.; Oka, K.; Ohnuki, S.; Akasaka, N.; Ukai, S.

2002-01-01

Oxide dispersion-strengthened ferritic steels were irradiated by neutrons up to 21 dpa and studied by microstructural observation and microchemical analysis. The original high dislocation density did not change after neutron irradiation, indicating that the dispersed oxide particles have high stability under neutron irradiation. However, there is potential for recoil resolution of the oxide particles due to ballistic ejection at high dose. From the microchemical analysis, it was implied that some of the complex oxides have a double-layer structure, such that TiO 2 occupied the core region and Y 2 O 3 the outer layer. Such a structure may be more stable than the simple mono-oxides. Under high-temperature irradiation, Laves phase was the predominant precipitate occurring at grain boundaries α phase and χ phase were not observed in this study

Effects of irradiation on color and lipid oxidation of prosciutto

International Nuclear Information System (INIS)

Kong Qiulian; Qi Wenyuan; Yue Ling; Chen Zhijun; Bao Yingzi; Dai Xudong; Xu Yun

2012-01-01

This study dealt with the effect of irradiation on the color, irradiation odor and lipid oxidation of prosciutto crudo. The hams were irradiated by γ-ray and electronic beam (EB). Changes of color, irradiation odor, TBA value (TBARS), peroxide value (POV), carbonyl value and conjugated diene value were analyzed and compared with non-irradiated hams. Results showed that color index (a * ) of control, γ-ray irradiated and EB irradiated were 14.39, 9.45 and 11.71 respectively. The ratios of a * /b * were different with the type of rays. The ratio of a * /b * of EB irradiation was same with control, while that of γ-ray irradiation was decreased apparently. γ-ray irradiation had been shown to have apparently detrimental effect on the color and odor of hams, while EB irradiation had little detrimental effect. Irradiation increased POV and conjugated diene value, but the amounts of lipid oxidation products (TBARS, carbonyl value) were less than nonirradiated hams. (authors)

Effects of irradiation on color and lipid oxidation of prosciutto

International Nuclear Information System (INIS)

Kong Qiulian; Qi Wenyuan; Yue Ling; Chen Zhijun; Bao Yingzi; Dai Xudong; Xu Yun

2011-01-01

This study dealt with the effect of irradiation on the color, ordor and lipid oxidation of prosciutto crudo. The hams were irradiated by γ-ray and electronic beam (EB). Changes of color, ordor, TBA value (TBARS), peroxide value (POV), carbonyl value and conjugated diene value were analyzed and compared with nonirradiated hams. Results showed that color index (a * ) of control, γ-ray irradiated and EB irradiated were 14.39, 9.45 and 11.71 respectively. γ-ray irradiation had been shown to have apparently detrimental effect on the color and ordor of hams, while EB irradiation had little detrimental effect. Irradiation increased POV and conjugated diene value, but the amounts of lipid oxidation products (TBARS, carbonyl value) were less than nonirradiated hams. (authors)

Methods of selenium and tellurium determination in geological and enviromental materials

International Nuclear Information System (INIS)

Nazarenko, I.I.; Kislova, I.V.

1988-01-01

Atomic-absorption and atomic-emission methods of tellurium determination in ores and products of their processing are described. Flame variant with extractional concentration permits to determine tellurium with the concentration up to 6x10 -6 %, the use of graphite cuvette after preliminary concentration-up to 1x10 -6 %. Atomic-emissional method permits to determine 3x10 -4 % Te from sample of 0.5 g

Effect of soy sauce on lipid oxidation of irradiated pork patties

International Nuclear Information System (INIS)

Kim, Hyun-Wook; Hwang, Ko-Eun; Choi, Yun-Sang; Choi, Ji-Hun; Lee, Mi-Ai; Song, Dong-Heon; Kim, Hack-Youn; Lee, Ju-Woon; Kim, Cheon-Jei

2013-01-01

This study was conducted to find out the antioxidant effect of the soy sauce on lipid oxidation of electron beam irradiated pork patties. The pork patties prepared with sodium chloride or soy sauce solution at identical salt concentrations were irradiated at 0 or 5 kGy, and peroxide value, conjugated diene, 2-thiobarbituric acid, and free fatty acid values were evaluated for 10 days (4 °C). The irradiated pork patties treated with soy sauce showed the lowest peroxide value and 2-thiobarbituric acid value at the end of storage compared to those prepared with sodium chloride. The irradiated pork patties formulated with soy sauce and 0.5% ascorbic acid had similar 2-thiobarbituric acid and free fatty acid values compared to those of the non-irradiated pork patties treated with sodium chloride. Our results suggested that the soy sauce can retard the lipid oxidation of irradiated pork patty, and a synergistic effect between soy sauce and ascorbic acid was observed. - Highlights: • Antioxidant effect of soy sauce on irradiated pork patties was studied. • The soy sauce can retard lipid oxidation of the irradiated pork patties. • A synergistic effect of ascorbic acid for preventing lipid oxidation was observed

Study of bixin oxidation by ionizing irradiation

International Nuclear Information System (INIS)

Fonseca, Thais N.; Teixeira, Paula S.; Moura, Eduardo de; Geraldo, Áurea Beatriz C.

2017-01-01

Brazil is the world's largest producer of anatto, followed by Kenya and Peru. The fruit of the annatto tree is constituted by a capsule containing external spines and internal seeds with reddish coloration, providing a natural pigment which is environmentally efficient, being able to replace synthetic pigments and dyes. The active substance of the pigment is Bixin, which is a type of carotenoid which constitutes a greater percentage of pigment in these seeds and has a lipo soluble character. Bixin reacts with NaOH in a saponification reaction giving norbixin, which is water soluble. It is known that the destination of the dye extracted from the fruit is intended for industry, especially the food industry. The culture of annatto tree brings prospects of development in agricultural programs for medium and small producers, which are able to use decadent areas of other crops. In addition to the food sector, new applications for the pigment helps the development of family farming. The pigment extracted from annatto undergoes a natural oxidation; this work aims to evaluate this phenomenon and also the oxidation of the pigment after the irradiation process. This work also evaluates of the how the oxidation process is affected by irradiation and the modifications introduced to irradiated pigments. Irradiated and nonirradiated samples were characterized by thermogravimetry, UV-vis spectrophotometry and infrared spectroscopy (FTIR). The results are then discussed. (author)

Oxide glass structure evolution under swift heavy ion irradiation

International Nuclear Information System (INIS)

Mendoza, C.; Peuget, S.; Charpentier, T.; Moskura, M.; Caraballo, R.; Bouty, O.; Mir, A.H.; Monnet, I.; Grygiel, C.; Jegou, C.

2014-01-01

Highlights: • Structure of SHI irradiated glass is similar to the one of a hyper quenched glass. • D2 Raman band associated to 3 members ring is only observed in irradiated glass. • Irradiated state seems slightly different to an equilibrated liquid quenched rapidly. - Abstract: The effects of ion tracks on the structure of oxide glasses were examined by irradiating a silica glass and two borosilicate glass specimens containing 3 and 6 oxides with krypton ions (74 MeV) and xenon ions (92 MeV). Structural changes in the glass were observed by Raman and nuclear magnetic resonance spectroscopy using a multinuclear approach ( 11 B, 23 Na, 27 Al and 29 Si). The structure of irradiated silica glass resembles a structure quenched at very high temperature. Both borosilicate glass specimens exhibited depolymerization of the borosilicate network, a lower boron coordination number, and a change in the role of a fraction of the sodium atoms after irradiation, suggesting that the final borosilicate glass structures were quenched from a high temperature state. In addition, a sharp increase in the concentration of three membered silica rings and the presence of large amounts of penta- and hexacoordinate aluminum in the irradiated 6-oxide glass suggest that the irradiated glass is different from a liquid quenched at equilibrium, but it is rather obtained from a nonequilibrium liquid that is partially relaxed by very rapid quenching within the ion tracks

Selenium and tellurium as carbon substitutes

International Nuclear Information System (INIS)

Knapp, F.F. Jr.

1980-01-01

This review has summarized structure-activity studies with 75 Se- and /sup 123m/Te-labeled radiopharmaceuticals in which the selenium or tellurium heteroatom has been inserted between carbon-carbon bonds. The agents that have been investigated in most detail include steroids for adrenal imaging and long-chain fatty acids, and a variety of other unique agents have also been studied. Because of the great versatility of the organic chemistry of selenium and tellurium, there is continuing interest in the preparation of radiopharmaceuticals labeled with 75 Se, 73 Se, and /sup 123m/Te. There are two important factors which will determine the extent of future interest in such agents. These include the necessity of a decrease in the cost of highly enriched 122 Te to make the reactor production of /sup 123m/Te cost effective. In addition, the potential preparation of large amounts of 73 Se should stimulate the development of 73 Se-labeled radiopharmaceuticals

Irradiation test plan of oxidation-resistant graphite in WWR-K Research Reactor

International Nuclear Information System (INIS)

Sumita, Junya; Shibata, Taiju; Sakaba, Nariaki; Osaki, Hirotaka; Kato, Hideki; Fujitsuka, Kunihiro; Muto, Takenori; Gizatulin, Shamil; Shaimerdenov, Asset; Dyussambayev, Daulet; Chakrov, Petr

2014-01-01

Graphite materials are used for the in-core components of High Temperature Gas-cooled Reactor (HTGR) which is a graphite-moderated and helium gas-cooled reactor. In the case of air ingress accident in HTGR, SiO_2 protective layer is formed on the surface of SiC layer in TRISO CFP and oxidation of SiC does not proceed and fission products are retained inside the fuel particle. A new safety concept for the HTGR, called Naturally Safe HTGR, has been recently proposed. To enhance the safety of Naturally Safe HTGR ultimately, it is expected that oxidation-resistant graphite is used for graphite components to prevent the TRISO CFPs and fuel compacts from failure. SiC coating is one of candidate methods for oxidation-resistant graphite. JAEA and four graphite companies launched R&Ds to develop the oxidation-resistant graphite and the International Science and Technology Center (ISTC) partner project with JAEA and INP was launched to investigate the irradiation effects on the oxidation-resistant graphite. To determine grades of the oxidation-resistant graphite which will be adopted as irradiation test, a preliminary oxidation test was carried out. This paper described the results of the preliminary oxidation test, the plan of out-of-pile test, irradiation test and post-irradiation test (PIE) of the oxidation-resistant graphite. The results of the preliminary oxidation test showed that the integrity of the oxidation resistant graphite was confirmed and that all of grades used in the preliminary test can be adopted as the irradiation test. Target irradiation temperature was determined to be 1473 (K) and neutron fluence was determined to be from 0.54 × 10"2"5through 1.4 × 10"2"5 (/m"2, E>0.18MeV). Weight change, oxidation rate, activation energy, surface condition, etc. will be evaluated in out-of-pile test and weight change, irradiation effect on oxidation rate and activation energy, surface condition, etc. will be evaluated in PIE. (author)

A new tellurium-containing amphiphilic molecule induces apoptosis in HCT116 colon cancer cells.

Science.gov (United States)

Du, Peng; Saidu, Nathaniel Edward Bennett; Intemann, Johanna; Jacob, Claus; Montenarh, Mathias

2014-06-01

Chalcogen-based redox modulators over the years have attracted considerable attention as anti-cancer agents. New selenium- and tellurium-containing compounds with a polar head group and aryl-groups of various lengths have recently been reported as biologically active in several organisms. In the present study, we used the most active of the tellurium compound DP41, and its selenium counterpart DP31 to investigate their effects on the human cancer cell line HCT116. Cells were treated with DP41 or DP31 and the formation of superoxide radicals was determined using dihydroethidium. Cell cycle analysis and apoptosis was determined by cytofluorimetry. Proteins involved in ER signaling and apoptosis were determined by Western blot analysis and fluorescence microscopy. With 50μM of DP41, we observed an increase in O2(-) formation. There was, however, no such increase in O2(-) after treatment with the corresponding selenium compound under the same conditions. In the case of DP41, the production of O2(-) radicals was followed by an up-regulation of Nrf2, HO-1, phospho-eIF2α and ATF4. CHOP was also induced and cells entered apoptosis. Unlike the cancer cells, normal retinal epithelial ARPE-19 cells did not produce elevated levels of O2(-) radicals nor did they induce the ER signaling pathway or apoptosis. The tellurium-containing compound DP41, in contrast to the corresponding selenium compound, induces O2(-) radical formation and oxidative and ER stress responses, including CHOP activation and finally apoptosis. These results indicate that DP41 is a redox modulating agent with promising anti-cancer potentials. Copyright © 2014 Elsevier B.V. All rights reserved.

Establishment of evaluation system for oxidation/anti-oxidation in living organisms using radiation irradiation and its practical application

International Nuclear Information System (INIS)

Umegaki, Keizo

2000-01-01

Basic study on the degree of oxidation damages after X-ray irradiation and changes in the anti-oxidative defense action was made using the rat. In addition, amplification of trace DNA damages by X-ray irradiation was investigated with human lymphocytes. Wistar rats were exposed to X-ray at 3 Gy under no anesthetization and killed after various time after the irradiation. The content of vitamin C, an anti-oxidant vitamin C in the bone marrow was markedly reduced by X-ray irradiation and the content after 24 hours from the irradiation was about 2% of that of the unexposed group. The content of vitamin E in the bone marrow was ca. 43% of that of the unexposed group. However, the contents of these anti-oxidant vitamins gradually recovered from 3-4 days after the irradiation. On the other hand, the content of 4-hydroxynonenal among the aldehydes that were tested as the indicator for oxidation damage of lipid was significantly increased one day after the irradiation and the contents of hexanal and TBARS reached the maximum level 3 days after. However, daily administration of about 100-fold larger amount of vitamin E (α-tocopherol at 460 mg/kg) for 3 days before the irradiation resulted in an increase in its content in the bone marrow, but significant decreases in the vitamin E and C levels in the bone marrow 24 hours after X-ray irradiation and aldehyde contents were increased, suggesting that pre-irradiation administration of vitamin E has no effects on the damages of bone marrow cells. As an indicator of DNA damages, the rate of appearance for lymphocytes having micronuclei was determined. The number of such lymphocytes was not significantly changed by exercise, but the number after irradiation at 1.5 Gy was dose dependently increased. These results suggested that trace DNA oxidation damages produced by severe exercise were markedly amplified by X-ray irradiation in not-trained subjects. (M.N.)

Selective floatation-spectrophotometric determination of tellurium (4) with papaverine and butyl rhodamine B

International Nuclear Information System (INIS)

Skripchuk, V.G.

1981-01-01

It is shown, that papaverine reacts with a bromide complex of tellurium (4) to form a compound readily floated by toluene. The floatation is carried out from an aqueous solution, 5.2 M in H 2 SO 4 , 0.2 M in KBr and 5.4x10 -3 M in papaverine. The absorbance is a function of tellurium (4) concentration over a range of 5-100 μg Te/5 ml. Such a highly sensitive reagent as butylrhodamine B can be effectively substituted for papaverine. The floatation results in better selectivity. The method makes it possible to determine tellurium in blister, anodic and cathodic copper without matrix preseparation [ru

Oxidation kinetic changes of UO2 by additive addition and irradiation

International Nuclear Information System (INIS)

You, Gil-Sung; Kim, Keon-Sik; Min, Duck-Kee; Ro, Seung-Gy

2000-01-01

The kinetic changes of air-oxidation of UO 2 by additive addition and irradiation were investigated. Several kinds of specimens, such as unirradiated-UO 2 , simulated-UO 2 for spent PWR fuel (SIMFUEL), unirradiated-Gd-doped UO 2 , irradiated-UO 2 and -Gd-doped UO 2 , were used for these experiments. The oxidation results represented that the kinetic patterns among those samples are remarkably different. It was also revealed that the oxidation kinetics of irradiated-UO 2 seems to be more similar to that of unirradiated-Gd-doped UO 2 than that of SIMFUEL

Magnetization measurements and XMCD studies on ion irradiated iron oxide and core-shell iron/iron-oxide nanomaterials

Energy Technology Data Exchange (ETDEWEB)

Kaur, Maninder; Qiang, You; Jiang, Weilin; Pearce, Carolyn; McCloy, John S.

2014-12-02

Magnetite (Fe3O4) and core-shell iron/iron-oxide (Fe/Fe3O4) nanomaterials prepared by a cluster deposition system were irradiated with 5.5 MeV Si2+ ions and the structures determined by x-ray diffraction as consisting of 100% magnetite and 36/64 wt% Fe/FeO, respectively. However, x-ray magnetic circular dichroism (XMCD) indicates similar surfaces in the two samples, slightly oxidized and so having more Fe3+ than the expected magnetite structure, with XMCD intensity much lower for the irradiated core-shell samples indicating weaker magnetism. X-ray absorption spectroscopy (XAS) data lack the signature for FeO, but the irradiated core-shell system consists of Fe-cores with ~13 nm of separating oxide crystallite, so it is likely that FeO exists deeper than the probe depth of the XAS (~5 nm). Exchange bias (Hex) for both samples becomes increasingly negative as temperature is lowered, but the irradiated Fe3O4 sample shows greater sensitivity of cooling field on Hex. Loop asymmetries and Hex sensitivities of the irradiated Fe3O4 sample are due to interfaces and interactions between grains which were not present in samples before irradiation as well as surface oxidation. Asymmetries in the hysteresis curves of the irradiated core/shell sample are related to the reversal mechanism of the antiferromagnetic FeO and possibly some near surface oxidation.

Chalcogen doping of silicon via intense femtosecond-laser irradiation

International Nuclear Information System (INIS)

Sheehy, Michael A.; Tull, Brian R.; Friend, Cynthia M.; Mazur, Eric

2007-01-01

We have previously shown that doping silicon with sulfur via femtosecond-laser irradiation leads to near-unity absorption of radiation from ultraviolet wavelengths to below band gap short-wave infrared wavelengths. Here, we demonstrate that doping silicon with two other group VI elements (chalcogens), selenium and tellurium, also leads to near-unity broadband absorption. A powder of the chalcogen dopant is spread on the silicon substrate and irradiated with femtosecond-laser pulses. We examine and compare the resulting morphology, optical properties, and chemical composition for each chalcogen-doped substrate before and after thermal annealing. Thermal annealing reduces the absorption of below band gap radiation by an amount that correlates with the diffusivity of the chalcogen dopant used to make the sample. We propose a mechanism for the absorption of below band gap radiation based on defects in the lattice brought about by the femtosecond-laser irradiation and the presence of a supersaturated concentration of chalcogen dopant atoms. The selenium and tellurium doped samples show particular promise for use in infrared photodetectors as they retain most of their infrared absorptance even after thermal annealing-a necessary step in many semiconductor device manufacturing processes

Investigation of biomethylation of arsenic and tellurium during composting

International Nuclear Information System (INIS)

Diaz-Bone, Roland A.; Raabe, Maren; Awissus, Simone; Keuter, Bianca; Menzel, Bernd; Kueppers, Klaus; Widmann, Renatus; Hirner, Alfred V.

2011-01-01

Though the process of composting features a high microbiological activity, its potential to methylate metals and metalloids has been little investigated so far in spite of the high impact of this process on metal(loid) toxicity and mobility. Here, we studied the biotransformation of arsenic, tellurium, antimony, tin and germanium during composting. Time resolved investigation revealed a highly dynamic process during self-heated composting with markedly differing time patterns for arsenic and tellurium species. Extraordinary high concentrations of up to 150 mg kg -1 methylated arsenic species as well as conversion rates up to 50% for arsenic and 5% for tellurium were observed. In contrast, little to no conversion was observed for antimony, tin and germanium. In addition to experiments with metal(loid) salts, composting of arsenic hyperaccumulating ferns Pteris vittata and P. cretica grown on As-amended soils was studied. Arsenic accumulated in the fronds was efficiently methylated resulting in up to 8 mg kg -1 methylated arsenic species. Overall, these studies indicate that metal(loid)s can undergo intensive biomethylation during composting. Due to the high mobility of methylated species this process needs to be considered in organic waste treatment of metal(loid) contaminated waste materials.

Determining arsenic in elemental antimony containing selenium and tellurium

International Nuclear Information System (INIS)

Mogileva, M.G.; Kozlova, E.L.

1986-01-01

The authors have developed a method of determining arsenic in metallic antimony containing selenium, tellurium, and mercury, in which they isolated it in elementary form for separation from the antimony and the associated elements (silicon and phosphorus), followed by colorimetric determination of the arsenic from arsenic-molbdenum blue. The reducing agents to reduce the arsenic were sodium hypophosphite and tin(II) chloride, which do not reduce antimony and which do not interfere with the determination. This method of determining arsenic in metallic antimony without preliminary separation of the selenium and tellurium is in no way inferior in accuracy to the method given in All-Union State Standard (GOST) 1367.4-83

Facile Hydrothermal Synthesis of Tellurium Nanostructures for Solar Cells

Directory of Open Access Journals (Sweden)

M. Panahi-Kalamuei

2014-10-01

Full Text Available Tellurium (Te nanostructures have been successfully synthesized via a simple hydrothermal methodfrom the reaction of a TeCl4 aqueous solution with thioglycolic acid (TGA as a reductant. TGA can be easily oxidized to the corresponding disulfide [SCH2CO2H]2, which in turn can reduce TeCl4 to Te. The obtained Te was characterized by XRD, SEM, EDS, and DRS. The effect of reducing agent on morphology and size of the products were also studied. Additionally, Te thin film was deposited on the FTO-TiO2 by Dr- blading then employed to solar cell application and measured open circuit voltage (Voc, short circuit current (Isc, and fill factor (FF were determined as well. The studies showed that particle morphology and sizes play crucial role on solar cell efficiencies.

METALCOMPLEXES OF TELLURIUM-CONTAINING AMINES AND AZOMETINES

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2014-01-01

Full Text Available In this article methods of synthesis and reactionary ability of metalcomplexes of tellurium-containing amines, azometines, of a problem of competitive coordination with use of the principle of "soft" and "rigid" acids and the bases (R. Pearson.

The characterisation of vapour-phase alkali metal-tellurium-oxygen species

International Nuclear Information System (INIS)

Gomme, R.A.; Ogden, J.S.; Bowsher, B.R.

1986-10-01

Detailed assessments of hypothetical severe accidents in light water reactors require the identification of the chemical forms of the radionuclides in order to determine their transport characteristics. Caesium and tellurium are important volatile fission products in accident scenarios. This report describes detailed studies to characterise the chemical species that vaporise from heated mixtures of various alkali metal-tellurium-oxygen systems. The molecular species were characterised by a combination of quadrupole mass spectrometry and matrix isolation-infrared spectroscopy undertaken in conjunction with experiments involving oxygen-18 substitution. The resulting spectra were interpreted in terms of a vapour-phase molecule with the stoichiometry M 2 TeO 3 (M = K,Rb,Cs) for M/Te molecular ratios of ∼ 2, and polymeric species for ratios < 2. This work has demonstrated the stability of caesium tellurite. The formation of this relatively low-volatility, water-soluble species could significantly modify the transport and release of caesium and tellurium. The data presented in this report should allow more comprehensive thermodynamic calculations to be undertaken that assist in the quantification of fission product behaviour during severe reactor accidents. (author)

Evolution of zirconium-based precipitates during oxidation and irradiation of Zr alloys (impact on the oxidation kinetics of Zr alloys)

International Nuclear Information System (INIS)

Pecheur, Dominique

1993-01-01

As the oxidation of the zircaloy sheath is one of the factors which limit the lifetime of nuclear fuel rods, this research thesis aims at a better knowledge of the involved oxidation mechanisms and to improve the oxidation resistance in order to increase rod lifetime. Oxidation test performed in autoclave to study zirconium alloy oxidation without irradiation showed that oxidation kinetics is significantly higher under irradiation. This difference is attributed to a different evolution of the sheath material under irradiation. Thus, this research focused on the role of precipitates in the oxidation process of zirconium alloys, and on the impact of their amorphization on this oxidation. After a detailed description of the context and of the various implemented experimental means, the author presents the results obtained on a reference material on the one hand, and on a material irradiated by ions or neutrons on the other hand. More particularly, the author studied in these both cases the introduction of precipitates in the oxide layer by transmission electronic microscopy, and oxidation kinetics obtained in autoclave on these two types of material. He reports the analysis of the introduction of precipitates in the oxide layer formed on the reference material. He proposes interpretations for the evolutions of structure and of chemical compositions of precipitates in the oxide layer. These observations are then correlated with oxidation kinetics in these alloys. Finally, the author discusses results of oxidation tests obtained on materials irradiated by ions and by neutrons [fr

Sulfur, selenium, tellurium and polonium

International Nuclear Information System (INIS)

Berry, F.J.

1987-01-01

This chapter on the coordination compounds of sulfur, selenium, tellurium and polonium starts with an introduction to the bonding, valence and geometry of the elements. Complexes of the group VIB elements are discussed with particular reference to the halo and pseudohalide complexes, oxo acid complexes, oxygen and nitrogen donor complexes and sulfur and selenium donor complexes. There is a section on the biological properties of the complexes discussed. (UK)

Experimental studies on anti-oxidants reducing lipid peroxidation of irradiated mice

International Nuclear Information System (INIS)

Du Zeji; Liu Keliang; Su Liaoyuan

1993-08-01

The free radical plays an important role in the irradiation damage. The irradiation damage would be reduced if anti-oxidants is used, because anti-oxidants can scavenge free radicals and suppress lipid peroxidation. In the study, a fluoro-spectrophotometer was used to determine the changes of MDA levels in mice tissues and serum after irradiation and the protective effect of anti-oxidants of Vit E and DMSO on damage caused by free radicals. The results are as follows: (1) The highest MDA level was at 12 to 24 hours after irradiation dose of 3.0 Gy. (2) The MDA level is increasing with the increasing of irradiation dose. It means the MDA level can indicate the extent of irradiation damage. (3) Both Vit E and DMSO had a powerful effect on reducing MDA level, but the effect of DMSO was stronger than Vit E. The optimum doses of them were 0.25 mg/g body weight and 10 mg/g body weight respectively. (4) The best effect obtained was to use Vit E and DMSO simultaneously

RILIS-ionized mercury and tellurium beams at ISOLDE CERN

Energy Technology Data Exchange (ETDEWEB)

Day Goodacre, T., E-mail: thomas.day.goodacre@cern.ch [CERN (Switzerland); Billowes, J. [The University of Manchester, School of Physics and Astronomy (United Kingdom); Chrysalidis, K. [CERN (Switzerland); Fedorov, D. V. [Petersburg Nuclear Physics Institute (Russian Federation); Fedosseev, V. N.; Marsh, B. A. [CERN (Switzerland); Molkanov, P. L. [Petersburg Nuclear Physics Institute (Russian Federation); Rossel, R. E.; Rothe, S.; Seiffert, C. [CERN (Switzerland); Wendt, K. D. A. [Johannes Gutenberg Universität, Institut für Physik (Germany)

2017-11-15

This paper presents the results of ionization scheme development for application at the ISOLDE Resonance Ionization Laser Ion Source (RILIS). Two new ionization schemes for mercury are presented: a three-step three-resonance ionization scheme, ionizing via an excitation to a Rydberg level and a three-step two-resonance ionization scheme, with a non-resonant final step to the ionization continuum that corresponded to a factor of four higher ionization efficiency. The efficiency of the optimal mercury ionization scheme was measured, together with the efficiency of a new three-step three resonance ionization scheme for tellurium. The efficiencies of the mercury and tellurium ionization schemes were determined to be 6 % and >18 % respectively.

Nano-Structured Crystalline Te Films by Laser Gas-Phase Pyrolysis of Dimethyl Tellurium

Czech Academy of Sciences Publication Activity Database

Pola, Josef; Pokorná, Veronika; Boháček, Jaroslav; Bastl, Zdeněk; Ouchi, A.

2004-01-01

Roč. 71, č. 2 (2004), s. 739-746 ISSN 0165-2370 R&D Projects: GA AV ČR IAA4072107; GA MŠk OC 523.60 Institutional research plan: CEZ:AV0Z4072921; CEZ:AV0Z4032918; CEZ:AV0Z4040901 Keywords : dimethyl tellurium * tellurium films * laser Subject RIV: CA - Inorganic Chemistry Impact factor: 1.352, year: 2004

Gamma Radiation Dosimetry Using Tellurium Dioxide Thin Film Structures

Directory of Open Access Journals (Sweden)

Olga Korostynska

2002-08-01

Full Text Available Thin films of Tellurium dioxide (TeO2 were investigated for γ-radiation dosimetry purposes. Samples were fabricated using thin film vapour deposition technique. Thin films of TeO2 were exposed to a 60Co γ-radiation source at a dose rate of 6 Gy/min at room temperature. Absorption spectra for TeO2 films were recorded and the values of the optical band gap and energies of the localized states for as-deposited and γ-irradiated samples were calculated. It was found that the optical band gap values were decreased as the radiation dose was increased. Samples with electrical contacts having a planar structure showed a linear increase in current values with the increase in radiation dose up to a certain dose level. The observed changes in both the optical and the electrical properties suggest that TeO2 thin film may be considered as an effective material for room temperature real time γ-radiation dosimetry.

Thermoelectric properties of electrodeposited tellurium films and the sodium lignosulfonate effect

International Nuclear Information System (INIS)

Abad, Begoña; Rull-Bravo, Marta; Hodson, Stephen L.; Xu, Xianfan; Martin-Gonzalez, Marisol

2015-01-01

The effect of the addition of a surfactant, sodium lignosulfonate (SLS), on the thermoelectric properties of tellurium films prepared by electrochemical deposition is studied. The growth mechanism is found to have an important role in the thermoelectric properties since the grain size of the films is sharply reduced when the surfactant is added to the solution. For this reason, the electrical resistivity of the tellurium films when the surfactant is not added is 229 μΩ·m, which is lower than 798 μΩ·m with SLS. The Seebeck coefficient values are not influenced, with values in the vicinity of 285 μV/K for both solutions. The power factor resulted higher values than previous works, reaching values of 280 μW/m·K 2 (without SLS) and 82 μW/m·K 2 (with SLS) at room temperature. Finally, the thermal conductivity was measured by means of the Photoacoustic technique, which showed values of the order of 1 W/m·K for both solutions, which is a factor of 3 less than the bulk value of tellurium. A notable observation is that the power factor and the thermal conductivity of electrodeposited tellurium films have the same order of magnitude of bismuth telluride films grown by electrodeposition. The figure of merit is estimated to be approximately one order of magnitude higher than the bulk value, 0.09 without SLS and 0.03 with SLS, both at room temperature

TL response to quartz and aluminum oxide grain for α-irradiation

International Nuclear Information System (INIS)

Pan Baolin; Wei Mingjian; Li Dongxu; Liu Zhaowen; Liu Chao; Zhao Shiyuan

2009-01-01

Thermoluminescence (TL) response for an α-ray irradiation system ( 241 Am) was examined with quartz grains of 11-40 μm. Quartz grains of different sizes, i.e. 137 Cs), before they were irradiated to different doses by the α-ray irradiation system. TL response to the quartz grain samples was measured. TL response of the quartz grains smaller than 4 μm and 11-40 μm to α-ray irradiation is the best, as the α-rays cannot penetrate quartz larger than 40 μm. The TL response characteristic is related with quartz grain surface area. TL responses to α-irradiation of 11-40 μm quartz and aluminum oxide grains were compared. The α-irradiation TL response of aluminum oxide (330 degree C) is better than the quartz (375 degree C). (authors)

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses.

Science.gov (United States)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-05-19

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO(2))(1 - x)(ZnO)(x) (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T(g) has been determined for each glass, showing a monotonous decrease of T(g) with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T(d) very close to the respective T(g) values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T(g) in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T(g) and confirms the correlation between the BP and the MRO of glasses.

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses

International Nuclear Information System (INIS)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T g has been determined for each glass, showing a monotonous decrease of T g with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T d very close to the respective T g values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T g in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T g and confirms the correlation between the BP and the MRO of glasses.

Effect of irradiation on lipid oxidation in eviscerated chicken carcasses during storage

International Nuclear Information System (INIS)

Hassan, I.M.; Hussein, M.F.; Mahmoud, A.A.; Hegazy, R.A.

1988-01-01

Oxidative changes induced in pectoralis major muscle of chicken after irradiation treatments with 0,6,10 and 20 KGy in both non frozen or frozen conditions during subsequent storage were investigated. Ultraviolet (UV) absorption, peroxides and thiobarbituric reactive substances increased in chicken lipids with increasing irradiation doses. These oxidative changes are greater in irradiated refrigerated (4 ± 1°C) than in irradiated frozen (-20°C) chicken lipids during storage. It was found the peroxides and TBA reactive substances do not accumulate as a stable end products of fat oxidation but reach a maximum during storage followed by gradual declining. The UV absorption provides an objective measure of chicken lipids autoxidation suitable for following the progress of autoxidation of irradiated chicken during subsequent non frozen (4 ± 1°C) or frozen (-20°C) storage. The extent of Maillard-like browning was followed in both unirradiated and irradiated samples during storage. All tested objective parameters correlated well with sensory assessment of odour particularly when irradiation dose was increased as well as in frozen samples

Effects of diet, packaging, and irradiation on protein oxidation, lipid oxidation, and color of raw broiler thigh meat during refrigerated storage.

Science.gov (United States)

Xiao, S; Zhang, W G; Lee, E J; Ma, C W; Ahn, D U

2011-06-01

This study was designed to evaluate the effects of dietary treatment, packaging, and irradiation singly or in combination on the oxidative stability of broiler chicken thigh meat. A total of 120 four-week-old chickens were divided into 12 pens (10 birds/pen), and 4 pens of broilers were randomly assigned to a control oxidized diet (5% oxidized oil) or an antioxidant-added diet [500 IU of vitamin E + 200 mg/kg of butylated hydroxyanisole (BHA)] and fed for 2 wk. After slaughter, thigh meats were separated, ground, packaged in either oxygen-permeable or oxygen-impermeable vacuum bags, and irradiated at 0 or 3 kGy. Lipid oxidation (TBA-reactive substances), protein oxidation (carbonyl), and color of the meat were measured at 1, 4, and 7 d of refrigerated storage. The lipid and protein oxidation of thigh meats from birds fed the diet supplemented with antioxidants (vitamin E + BHA) was significantly lower than the lipid and protein oxidation of birds fed the control diet, whereas the lipid and protein oxidation of broilers fed the oxidized oil diet was higher than that of birds fed the control diet. Vacuum packaging slowed, but irradiation accelerated, the lipid and protein oxidation of thigh meat during storage. Dietary antioxidants (vitamin E + BHA) and irradiation treatments showed a stronger effect on lipid oxidation than on protein oxidation. A significant correlation between lipid and protein oxidation in meat was found during storage. Dietary supplementation of vitamin E + BHA and the irradiation treatment increased the lightness and redness of thigh meat, respectively. It is suggested that appropriate use of dietary antioxidants in combination with packaging could be effective in minimizing oxidative changes in irradiated raw chicken thigh meat.

Improvement of biological properties of titanium by anodic oxidation and ultraviolet irradiation

Energy Technology Data Exchange (ETDEWEB)

Li, Baoe [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050 (China); Li, Ying [Stomatological Hospital, Tianjin Medical University, Tianjin 300070 (China); Li, Jun [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Fu, Xiaolong; Li, Changyi [Stomatological Hospital, Tianjin Medical University, Tianjin 300070 (China); Wang, Hongshui [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Liu, Shimin [Business School, Tianjin University of Commerce, Tianjin 300134 (China); Guo, Litong [China University of Mining and Technology, Xuzhou 221116 (China); Xin, Shigang [Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050 (China); Liang, Chunyong, E-mail: liangchunyong@126.com [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Li, Haipeng, E-mail: lhpcx@163.com [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China)

2014-07-01

Anodic oxidation was applied to produce a homogeneous and uniform array of nanotubes of about 70 nm on the titanium (Ti) surface, and then, the nanotubes were irradiated by ultraviolet. The bioactivity of the Ti surface was evaluated by simulated body fluid soaking test. The biocompatibility was investigated by in vitro cell culture test. The results showed that bone-like apatite was formed on the anodic oxidized and UV irradiated Ti surface, but not on the as-polished Ti surface after immersion in simulated body fluid for two weeks. Cells cultured on the anodic oxidized Ti surface showed enhanced cell adhesion and proliferation, also presented an up-regulated gene expression of osteogenic markers OPG, compared to those cultured on the as-polished Ti surface. After UV irradiation, the cell behaviors were further improved, indicating better biocompatibility of Ti surface. Based on these results, it can be concluded that anodic oxidation improved the biological properties (bioactivity and biocompatibility) of Ti surface, while UV irradiation improved the biocompatibility to a better extent. The improved biological properties were attributed to the nanostructures as well as the enhanced hydrophilicity. Therefore, anodic oxidation combined with UV irradiation can be used to enhance the biological properties of Ti-based implants.

Stability under irradiation of a fine dispersion of oxides in a ferritic matrix

International Nuclear Information System (INIS)

Monnet, I.

1999-01-01

Oxide dispersion strengthened (ODS) ferritic-martensitic steels are being considered for high temperature, high fluence nuclear applications, like fuel pin cladding in Fast Breeder Reactors. ODS alloys offer improved out of pile strength characteristics at temperature above 550 deg.C and ferritic-martensitic matrix is highly swelling resistant. A clad in an ODS ferritic steel, call DY (Fe-13Cr-1,5Mo+TiO 2 +Y 2 O 3 ) has been irradiated in the experimental reactor Phenix. Under irradiation oxide dissolution occurs. Microstructural observations indicated that oxide evolution is correlated with the dose and consist in four phenomena: the interfaces of oxide particles with the matrix become irregular, the uniform distribution of the finest oxide ( 2 O 3 , Y 2 O 3 , MgO or MgAl 2 O 4 . These materials were irradiated with charged particles in order to gain a better understanding of the mechanisms of dissolution. Irradiation with 1 MeV Helium does not induce any modification, neither in the chemical modification of the particles nor in their spatial and size distribution. Since most of the energy of helium ions is lost by inelastic interaction, this result proves that this kind of interaction does not induce oxide dissolution. Irradiation with 1 MeV or 1.2 MeV electrons leads to a significant dissolution with a radius decrease proportional to the dose. These experiments prove that oxide dissolution can be induced by Frenkel pairs alone, provided that metallic atoms are displaced. The comparison between irradiation with ions (displacements cascades) and electrons (Frenkel pairs only) shows the importance of free point defects in the dissolution phenomena. For all the irradiations (ions or electrons) the spinel MgAl 2 O 4 seems more resistant than Y 2 O 3 to dissolution, and MgO and Al 2 O 3 are even less resistant. This is the order of stability under irradiation of bulk oxides. (author)

Tellurium Stable Isotopes as a Paleoredox Proxy

Science.gov (United States)

Wasserman, N.; Johnson, T. M.

2017-12-01

Despite arguments for variably-oxygenated shallow waters and anoxic deep marine waters, which delayed animal development until the Neoproterozoic Oxidation Event, the magnitude of atmospheric oxygen during the Proterozoic is still uncertain [1]. The evidence for low pO2 (<0.1-1% PAL) is based on geochemical and isotopic proxies, which track the mobilization of Fe and Mn on the continents. For example, large chromium isotope shifts occur at the Neoproterozoic Oxidation Event due to the initiation of Cr redox cycling, but this proxy is insensitive to fluctuations in the lower-pO2 conditions at other times during the Proterozoic. Tellurium, a metalloid with a lower threshold to oxidation, may be sensitive to pO2 shifts in a lower range. In the reduced forms, Te(-II) and Te(0), the element is insoluble and immobile. However, in the more oxidized phases, Te(IV) and Te(VI), Te can form soluble oxyanions (though it tends to adsorb to Fe-oxyhydroxides and clays) [2]. Te stable isotopes have been shown to fractionate during abiotic or biologic reduction of Te(VI) or Te(IV) to elemental Te(0) [3, 4]. Utilizing hydride generation MC-ICP-MS, we are able to obtain high precision (2σ 0.04‰) measurements of δ128Te/125Te for natural samples containing < 10 ng of Te. A suite of Phanerozoic and Proterozoic ironstones show significant variation in δ128Te/125Te (<0.5‰), suggesting that the Te redox cycle was active during the Proterozoic. Future directions will include Te isotope measurements of Precambrian paleosols to determine natural isotope variation before the Great Oxidation Event and experiments to determine fractionation during adsorption to Fe-oxyhydroxides. [1] Planavsky et al. (2014) Science 346 (6209), pp. 635-638 [2] Qin et al. (2017) Environmental Science and Technology 51 (11), pp 6027-6035 [3] Baesman et al. (2007) Applied Environmental Microbiology 73 (7), pp 2135-2143 [4] Smithers and Krause (1968) Canadian Journal of Chemistry 46(4): pp 583-591

Ecological aspects of selenium and tellurium in human and animal health

Energy Technology Data Exchange (ETDEWEB)

Frost, D V; Ingvoldstad, D

1975-01-01

Animal and human studies indicate that selenium inadequacy, in part, underlies various chronic diseases. Epidemiologic evidence suggests that cancer and heart disease are most common where ambient Se availability is low. Plant Se uptake and Se blood levels are inverse to human cancer mortality. As the active group in glutathione peroxidase, Se/sup -2/ inhibits aberrant oxidations which lead to chronic diseases. It binds heavy metals, and with tocopherol maintains tissue integrity. Sulfur dioxide fallout from the atmosphere, resulting from fossil fuel burning, may diminish the nutritional availability of selenium by diminishing plant uptake. Intensive ruminant grazing returns unavailable Se/sup 0/ to soils. Trimethyl selenium ion, as excreted by animals, also appears to be unavailable to plants. Modern fertilization practices and the effect of buildup of sulfates in the soil, due to acid rains, both appear to lessen the availability of Se to plants. SeO/sub 2/ added to the atmosphere from combustion and volcanic activity react with SO/sub 2/ to yield Se/sup 0/. This is presumed to fall out as particles from the air. How traces of Se are otherwise carried in air, explaining its enrichment in some areas, is unknown. The New Zealand experience with Se inadequacy in animals and man may be repeated in other parts of the world. Se inadequacy is far more of a human health problem than Se toxicity. There are no known adverse health effects from tellurium, other than tellurium breath. 164 references, 5 figures, 3 tables.

Chemical Process for Treatment of Tellurium and Chromium Liquid Waste from I-131 Radioisotope Production

International Nuclear Information System (INIS)

Zainus-Salimin; Gunandjar; Dedy-Harsono; Hendro; Sugeng-Purnomo; Mohammad-Faruq; Zulfakhri

2000-01-01

The I-131 radioisotope is used in nuclear medicine for diagnosis and therapy. The I-131 radioisotope is produced by wet distillation at Bandung Nuclear Research Center and generated about 4,875 Itr of liquid waste containing 2,532.8 ppm of tellurium and 1,451.8 ppm chromium at pH 1. Considering its negative impact to the environment caused by toxic behaviour of tellurium and chromium, it is necessary to treat chemically that's liquid waste. The research of chemical treatment of tellurium and chromium liquid waste from I-131 radioisotope production has been done. The steps of process are involved of neutralisation with NaOH, coagulation-flocculation process for step I using Ca(OH) 2 coagulant for precipitation of sulphate, sulphite, oxalic, chrome Cr 3+ , and coagulation-flocculation process for step II using BaCI 2 coagulant for precipitation of chrome Cr 6+ and tellurium from the supernatant of coagulation in step I. The best result of experiment was achieved at 0.0161 ppm of chromium concentration on the supernatant from coagulation-flocculation of step I using 3.5 g Ca(OH) 2 for 100 ml of liquid waste, and 0.95 ppm of tellurium concentration on the final supernatant from coagulation-flocculation by of step II using 0.7 g BaCI 2 for supernatant from coagulation of step I. (author)

Enhancement of Au-Ag-Te contents in tellurium-bearing ore minerals via bioleaching

Science.gov (United States)

Choi, Nag-Choul; Cho, Kang Hee; Kim, Bong Ju; Lee, Soonjae; Park, Cheon Young

2018-03-01

The purpose of this study was to enhance the content of valuable metals, such as Au, Ag, and Te, in tellurium-bearing minerals via bioleaching. The ore samples composed of invisible Au and Au paragenesis minerals (such as pyrite, chalcopyrite, sphalerite and galena) in combination with tellurium-bearing minerals (hessite, sylvanite and Tellurobismuthite) were studied. Indigenous microbes from mine drainage were isolated and identified as Acidithiobacillus ferrooxidans, which were used in bioleaching after adaption to copper. The effect of the microbial adaption on the bioleaching performance was then compared with the results produced by the non-adaptive process. The microbial adaption enhanced the Au-Ag-Te contents in biological leaching of tellurium-bearing ore minerals. This suggests that bioleaching with adapted microbes can be used both as a pretreatment and in the main recovery processes of valuable metals.

The effect of electron beam irradiation on lipid oxidation in sausages

Directory of Open Access Journals (Sweden)

atefeh yousefi

2017-09-01

Full Text Available Introduction: Irradiation treatment is one of the best techniques to extend the shelf-life of meat, without emerging the nutritional properties and sensory quality of irradiated meat products.  However electron -beam  may cause transformations in foods but has been known as to the most easily-applied irradiation technique in food industries. Electron-beam irradiation is an environment friendly, low cost and time effective alternative to other decontamination technologies. Lipid oxidation could produce of irradiated meat. This study aimed at evaluating the state of lipid oxidation of irradiated sausages. Its findings could help the control, improve food safety and quality properties to food industries. Methods: Sausages were purchased in a local supermarket, minced sausages blended for thiobarbituric acid reactive substances (TBARS analysis and divided into 25 g pieces. The samples including one control group and four case groups. Packaged sausage were exposed at doses of 0 (control, 1, 2, 3 and 5 kGy and analyzed on various days 0, 5, 10 and 30. Results: Thiobarbituric acid reactive substances (TBARS has increased as time goes on (P<0.05. A significant relationship was observed on different Doses. But, the maximum of TBARS was observed in 3 kGy. Conclusion: Utilizing of Electron-beam irradiation in low doses does not have significant difference on lipid oxidation. Irradiating of meat products by addition of antioxidants can minimize or avoid the development of rancidity.

Dose dependent oxidation kinetics of lipids in fish during irradiation processing

International Nuclear Information System (INIS)

Tukenmez, I.; Ersen, M.S.; Bakioglu, A.T.; Bicer, A.; Pamuk, V.

1997-01-01

Kinetic aspects of the development of lipid oxidation in complex foods as fish in the course of irradiation were analyzed with respect to the associated formation of malonaldehyde (MA) through the reactions modified so as to be consistent with those in complex foods as fish. Air-packed anchovy (Engraulis encrasicholus) samples in polyethylene pouches were irradiated at the doses of 1, 2, 5, 10, 15,20 and 25 kGy at 20 o C in a Cs-137 gamma irradiator of 1.806 kGy/h dose rate. Immediately after each irradiation, MA contents of irradiated and unirradiated samples were determined by thiobarbituric acid test. Based on the MA formation, a kinetic model to simulate the apparent oxidation of lipid in fish as a function of irradiation dose was derived from the rate equations consistent with modified reactions. Kinetic parameters and simulation were related to conditions of lipid oxidation, and associated rancidity state of fish with respect to the doses applied in different irradiation-preservation processes. Numerical values of kinetic parameters based on the MA formation were found as a threshold dose of 0.375 kGy, an apparent yield of 1.871 μmol/kg kGy, and a maximum attainable concentration of 15.853 μmol/kg which may be used for process control and dosimetry. (author)

Electron microscope study of irradiated beryllium oxide

International Nuclear Information System (INIS)

Bisson, A.A.

1965-06-01

The beryllium oxide is studied first by fractography, before and after irradiation, using sintered samples. The fractures are examined under different aspects. The higher density sintered samples, with transgranular fractures are the most interesting for a microscopic study. It is possible to mark the difference between the 'pores' left by the sintering process and the 'bubbles' of gases that can be produced by former thermal treatments. After irradiation, the grain boundaries are very much weakened. By annealing, it is possible to observe the evolution of the gases produced by the reaction (n, 2n) and (n. α) and gathered on the grain boundaries. The irradiated beryllium oxide is afterwards studied by transmission. For that, a simple method has been used: little chips of the crushed material are examined. Clusters of point defects produced by neutrons are thus detected in crystals irradiated at the three following doses: 6 x 10 19 , 9 x 10 19 and 2 x 10 20 n f cm -2 at a temperature below 100 deg. C. For the irradiation at 6 x 10 19 n f cm -2 , the defects are merely visible, but at 2 x l0 20 n f cm -2 the crystals an crowded with clusters and the Kikuchi lines have disappeared from the micro-diffraction diagrams. The evolution of the clusters into dislocation loops is studied by a series of annealings. The activation energy (0,37 eV) calculated from the annealing curves suggests that it must be interstitials that condense into dislocation loops. Samples irradiated at high temperatures (650, 900 and 1100 deg. C) are also studied. In those specimens the size of the loops is not the same as the equilibrium size obtained after out of pile annealing at the same temperature. Those former loops are more specifically studied and their Burgers vector is determined by micro-diffraction. (author) [fr

Peroxide coordination of tellurium in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

2016-02-15

Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Post-Irradiation Behaviour of I131 in TeO2

International Nuclear Information System (INIS)

Jaćimović, Lj.; Stevović, J.; Veljković, S.R.

1965-01-01

The system I 131 in TeO 2 is interesting because little is known about thermal chemical changes in this target. Radioiodine was produced by neutron irradiation of TeO 2 in the reactor. Irradiated TeO 2 was dissolved in diluted NaOH. The analysis of the iodine valency forms was made by ion exchange techniques. The thermal and radiation stability of TeO 2 was studied by using the spectrophotometric method for the determination of tellurium. Post-irradiation annealing of I 131 in TeO 2 was studied in dependence on the time and temperature of the heating. The main tendency of annealing was the reduction of radioiodine. The time dependence of this process indicates a fast change at high temperatures. The curves are more complex at lower temperatures. The annealing may appear complex because of the variety of thermal reactions of iodine intermediary. It may react with products of the following processes: tellurium recoil and corresponding hot zone, beta transition of Te 131 and TeO 2 itself. The kinetics of these changes was considered and an estimation of the processes during annealing was made. The influence of the neutron flux on the kinetics of annealing was also studied. (author) [fr

Irradiation temperature dependence of production efficiency of lattice defects in some neutron-irradiated oxides

International Nuclear Information System (INIS)

Okada, Moritami; Atobe, Kozo; Nakagawa, Masuo

2004-01-01

Temperature dependence of production efficiency of irradiation-induced defects in neutron-irradiated oxides has been investigated. Some oxide single crystals, MgO, α-Al 2 O 3 (sapphire) and TiO 2 (rutile), were irradiated at several controlled temperatures, 10, 20, 50, 100, 150 and 200 K, using the low-temperature irradiation facility of Kyoto University Reactor (KUR-LTL), and at ambient temperature (∼370 K) in the same facility. Irradiation temperature dependence of production efficiency of a 1 μm band in TiO 2 differs greatly from that of anion vacancy (F-type centers) in MgO and α-Al 2 O 3 . Results for MgO and α-Al 2 O 3 show steep negative gradients from 10 to 370 K, whereas that for TiO 2 includes a valley between 40 and 60 K and a hump at about 130 K, and then disappear at about 200 K. In MgO and α-Al 2 O 3 , this behavior can be explained by the recombination of Frenkel pairs, which is activated at higher temperature. In TiO 2 , in addition to the recombination mechanism, a covalent bonding property is thought to be exerted strong influence, and it is suggested that a disappearance of the 1 μm band at above 200 K is due to the recombination process of Frenkel pairs which is caused by the irradiation-induced crystallization

Irradiation temperature dependence of production efficiency of lattice defects in some neutron-irradiated oxides

Energy Technology Data Exchange (ETDEWEB)

Okada, Moritami [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka 5900494 (Japan)]. E-mail: okada@rri.kyoto-u.ac.jp; Atobe, Kozo [Faculty of Science, Naruto University of Education, Naruto, Tokushima 7728502 (Japan); Nakagawa, Masuo [Faculty of Education, Kagawa University, Takamatsu, Kagawa 7608522 (Japan)

2004-11-01

Temperature dependence of production efficiency of irradiation-induced defects in neutron-irradiated oxides has been investigated. Some oxide single crystals, MgO, {alpha}-Al{sub 2}O{sub 3} (sapphire) and TiO{sub 2} (rutile), were irradiated at several controlled temperatures, 10, 20, 50, 100, 150 and 200 K, using the low-temperature irradiation facility of Kyoto University Reactor (KUR-LTL), and at ambient temperature ({approx}370 K) in the same facility. Irradiation temperature dependence of production efficiency of a 1 {mu}m band in TiO{sub 2} differs greatly from that of anion vacancy (F-type centers) in MgO and {alpha}-Al{sub 2}O{sub 3}. Results for MgO and {alpha}-Al{sub 2}O{sub 3} show steep negative gradients from 10 to 370 K, whereas that for TiO{sub 2} includes a valley between 40 and 60 K and a hump at about 130 K, and then disappear at about 200 K. In MgO and {alpha}-Al{sub 2}O{sub 3}, this behavior can be explained by the recombination of Frenkel pairs, which is activated at higher temperature. In TiO{sub 2}, in addition to the recombination mechanism, a covalent bonding property is thought to be exerted strong influence, and it is suggested that a disappearance of the 1 {mu}m band at above 200 K is due to the recombination process of Frenkel pairs which is caused by the irradiation-induced crystallization.

Luminescent Tellurium-Doped Cadmium Sulfide Electrodes as Probes of Semiconductor Excited-State Deactivation Processes in Photoelectrochemical Cells.

Science.gov (United States)

1980-08-12

photocurrent and emission intensity. Whereas CdS:Te electrochemistry consisted of oxidation of an electrolyte 2+ reductant, ZnO underwent photoanodic...employed n- and 1 3 2,3 3 3,4p-type GaPl’ n-type ZnO , n-type CdS , and n- and p-type GaAs. We have focussed our attention recently on n-type, tellurium...should point out that our treatment of Or and 0x is not without precedent. Both GaP- and ZnO -based PECs have been examined in this regard.l12 The

Rutherford backscatter measurements on tellurium and cadmium implanted gallium arsenide

International Nuclear Information System (INIS)

Bell, E.C.

1979-10-01

The primary aim of the work described in this thesis was to examine implanted layers of the dopant impurities cadmium and tellurium in gallium arsenide and to experimentally assess their potential for producing electrically active layers. 1.5 MeV Rutherford backscattering measurements of lattice disorder and atom site location have been used to assess post implantation thermal annealing and elevated temperature implantations to site the dopant impurities on either gallium or arsenic lattice positions in an otherwise undisordered lattice. Pyrolitically deposited silicon dioxide was used as an encapsulant to prevent thermal dissociation of the gallium arsenide during annealing. It has been shown that high doses of cadmium and tellurium can be implanted without forming amorphous lattice disorder by heating the gallium arsenide during implantation to relatively low temperatures. Atom site location measurements have shown that a large fraction of a tellurium dose implanted at 180 0 C is located on or near lattice sites. Channeled backscatter measurements have shown that there is residual disorder or lattice strain in gallium arsenide implanted at elevated temperatures. The extent of this disorder has been shown to depend on the implanted dose and implantation temperature. The channeling effect has been used to measure annealing of the disorder. (author)

Investigation of the interaction of copper(II) oxide and electron beam irradiation crosslinkable polyethylene

International Nuclear Information System (INIS)

Bee, Soo-Tueen; Sin, Lee Tin; Ratnam, C.T.; Haraveen, K.J.S.; Tee, Tiam-Ting; Rahmat, A.R.

2015-01-01

In this study, the effects of electron beam irradiation on the properties of copper(II) oxide when added to low-density polyethylene (LDPE) blends were investigated. It was found that the addition of low loading level of copper(II) oxide (⩽2 phr) to LDPE results in significantly poorer gel content and hot set results. However, the incorporation of higher loading level of copper(II) oxide (⩾3 phr) could slightly increase the degree of crosslinking in all irradiated LDPE composites. This is due to the fact that higher amounts of copper(II) oxide could slightly induce the formation of free radicals in LDPE matrix. Besides, increasing irradiation doses was also found to gradually increase the gel content of LDPE composites by generating higher amounts of free radicals. As a consequence, these higher amounts of free radicals released in the LDPE matrix could significantly increase the degree of crosslinking. The addition of copper(II) oxide could reduce the tensile strength and fracture strain (elongation at break) of LDPE composites because of poorer interfacial adhesion effect between copper(II) oxide particles and LDPE matrix. Meanwhile, increasing irradiation doses on all copper(II) oxide added LDPE composites could marginally increase the tensile strength. In addition, increasing irradiation dose could enhance the thermal stability of LDPE composites by increasing the decomposition temperature. The oxidation induction time (OIT) analysis showed that, because of the crosslinking network in the copper(II) oxide added LDPE composites, oxidation reaction is much delayed.

Investigation of the interaction of copper(II) oxide and electron beam irradiation crosslinkable polyethylene

Energy Technology Data Exchange (ETDEWEB)

Bee, Soo-Tueen, E-mail: direct.beest@gmail.com [Department of Chemical Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Sungai Long, Bandar Sungai Long, Cheras, 43000 Kajang, Selangor (Malaysia); Sin, Lee Tin, E-mail: direct.tinsin@gmail.com [Department of Chemical Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Sungai Long, Bandar Sungai Long, Cheras, 43000 Kajang, Selangor (Malaysia); Ratnam, C.T. [Radiation Processing Technology Division, Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia); Haraveen, K.J.S.; Tee, Tiam-Ting [Department of Chemical Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Sungai Long, Bandar Sungai Long, Cheras, 43000 Kajang, Selangor (Malaysia); Rahmat, A.R. [Department of Polymer Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia)

2015-10-01

In this study, the effects of electron beam irradiation on the properties of copper(II) oxide when added to low-density polyethylene (LDPE) blends were investigated. It was found that the addition of low loading level of copper(II) oxide (⩽2 phr) to LDPE results in significantly poorer gel content and hot set results. However, the incorporation of higher loading level of copper(II) oxide (⩾3 phr) could slightly increase the degree of crosslinking in all irradiated LDPE composites. This is due to the fact that higher amounts of copper(II) oxide could slightly induce the formation of free radicals in LDPE matrix. Besides, increasing irradiation doses was also found to gradually increase the gel content of LDPE composites by generating higher amounts of free radicals. As a consequence, these higher amounts of free radicals released in the LDPE matrix could significantly increase the degree of crosslinking. The addition of copper(II) oxide could reduce the tensile strength and fracture strain (elongation at break) of LDPE composites because of poorer interfacial adhesion effect between copper(II) oxide particles and LDPE matrix. Meanwhile, increasing irradiation doses on all copper(II) oxide added LDPE composites could marginally increase the tensile strength. In addition, increasing irradiation dose could enhance the thermal stability of LDPE composites by increasing the decomposition temperature. The oxidation induction time (OIT) analysis showed that, because of the crosslinking network in the copper(II) oxide added LDPE composites, oxidation reaction is much delayed.

Effect of soy sauce on lipid oxidation of irradiated pork patties

Science.gov (United States)

Kim, Hyun-Wook; Hwang, Ko-Eun; Choi, Yun-Sang; Choi, Ji-Hun; Lee, Mi-Ai; Song, Dong-Heon; Kim, Hack-Youn; Lee, Ju-Woon; Kim, Cheon-Jei

2013-09-01

This study was conducted to find out the antioxidant effect of the soy sauce on lipid oxidation of electron beam irradiated pork patties. The pork patties prepared with sodium chloride or soy sauce solution at identical salt concentrations were irradiated at 0 or 5 kGy, and peroxide value, conjugated diene, 2-thiobarbituric acid, and free fatty acid values were evaluated for 10 days (4 °C). The irradiated pork patties treated with soy sauce showed the lowest peroxide value and 2-thiobarbituric acid value at the end of storage compared to those prepared with sodium chloride. The irradiated pork patties formulated with soy sauce and 0.5% ascorbic acid had similar 2-thiobarbituric acid and free fatty acid values compared to those of the non-irradiated pork patties treated with sodium chloride. Our results suggested that the soy sauce can retard the lipid oxidation of irradiated pork patty, and a synergistic effect between soy sauce and ascorbic acid was observed.

Study On Analytical Methods Of Tellurium Content In Natriiodide (Na131I) Radiopharmaceutical Solution Produced In The Dalat Nuclear Reactor

International Nuclear Information System (INIS)

Vo Thi Cam Hoa; Duong Van Dong; Nguyen Thi Thu; Chu Van Khoa

2007-01-01

This report describes the practical methods for analyzing of Tellurium content in Na 131 I solution produced at the Dalat Nuclear Research Institute. We studied analytical methods to control Tellurium content in final Na 131 I solution product used in medical purposes by three methods such as: spot test, gamma spectrometric and spectrophotometric methods. These investigation results are shown that the spot test method is suitable for controlling Tellurium trace in the final product. This spot test can be determinate Tellurium trace less than 10 ppm and are used to quality control of Na 131 I solution using in medical application. (author)

Selenium- or tellurium- containing bile acids and derivatives thereof

International Nuclear Information System (INIS)

Monks, R.; Riley, A.L.M.

1981-01-01

This invention relates to the preparation of selenium and tellurium derivatives, particularly γ-emitting radioactive derivatives of bile acids and bile salts. Such compounds are valuable in the examination of body function, especially small bowel function. (author)

Speciation analysis of tellurium by solid-phase extraction in the presence of ammonium pyrrolidine dithiocarbamate and inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Yu, Chunhai; Cai, Qiantao; Guo, Zhong-Xian; Yang, Zhaoguang [Centre for Advanced Water Technology, Innovation Centre (NTU), Singapore (Singapore); Khoo, Soo Beng [Department of Chemistry, National University of Singapore (Singapore)

2003-05-01

Under acidic conditions tellurium(IV) formed a complex with ammonium pyrrolidine dithiocarbamate (APDC). The tellurium(IV) complex was completely retained on a non-polar Isolute silica-based octadecyl (C{sub 18}) sorbent-containing solid-phase extraction (SPE) cartridge, while the uncomplexed Te(VI) passed through the cartridge and remained as a free species in the solution. Only partial Te(IV) was retained on the SPE cartridge for samples without addition of APDC. On the basis of different retention behaviours of the complexed Te(IV) and uncomplexed Te(VI), a simple and highly sensitive method is proposed for the determination of total tellurium and Te(VI) by SPE separation and inductively coupled plasma mass spectrometry (ICP-MS) detection. The Te(IV) concentration was calculated as the difference between total tellurium and Te(VI) concentrations. The detection limit (3{sigma}) is 3 ng L{sup -1} tellurium. Factors affecting the separation and detection of tellurium species were investigated. Coexisting ions did not show significant interferences with the Te(IV)-APDC complex retention and the subsequent ICP-MS detection of Te. The method has been successfully applied to the tellurium speciation analysis in waters with spiked recoveries for Te(IV) and Te(VI) of 86.0-108% and 87.1-97.4%, respectively. (orig.)

Irradiation effects in superconductor oxides. Effets d'irradiation dans les oxydes supraconducteurs

Energy Technology Data Exchange (ETDEWEB)

Rullier-Albenque, F; Konczykowski, M [CEA-Ecole Polytechnique, 91 - Palaiseau (France). Lab. d' Etudes des Solides Irradies

1993-01-01

Several effects of irradiation on the 92 K - oxide superconductor YBa[sub 2]Cu[sub 3]O[sub 7] are reported. Whatever irradiation type, the critical temperature T[sub c] is found to decrease and the resistivity to increase. At sufficiently high damage levels, YBa[sub 2]Cu[sub 3]O[sub 7] is no longer superconducting and even displays a semiconducting-like behaviour. The alterations of superconducting properties are clearly related to oxygen defects - in the CuO[sub 2] planes or CuO chains... but we have shown experimentally that copper defects are also important. Magnetic properties of YBa[sub 2]Cu[sub 3]O[sub 7] in mixed state are also very sensitive to irradiation. By pinning the flux lines, irradiation defects can considerably increase the critical current density j[sub c]. At present, irradiations by highly energetic heavy ions (6 GeV Pb for instance), which produce cylindrical tubes of amorphous material (latent tracks) throughout the whole thickness of the samples, are probably the most efficient way to enhance j[sub c]. (Author). 18 refs., 7 figs.

Color and oxidative stability of nitrite-free cured meat after gamma irradiation

International Nuclear Information System (INIS)

Shahidi, F.; Pegg, R.B.; Shamsuzzaman, K.

1991-01-01

The effects of 5 and 10 kGy irradiation on the color and oxidative stability of meats treated with nitrite or a nitrite-free curing system were investigated. The nitrite-free curing system consisted of the preformed cooked cured-meat pigment, sodium ascorbate and sodium tripolyphosphate with or without sodium acid pyrophosphate. Irradiation had no detrimental effects on the color or flavor of either cured samples. Polyphosphates had a beneficial effect on oxidative stability but had a slight detrimental effect on color stability of irradiated samples

Simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples using hydride generation ICPMS

International Nuclear Information System (INIS)

Jankowski, L.M.; Breidenbach, R.; Bakker, I.J.I.; Epema, O.J.

2009-01-01

Full text: A quantitative method for simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples is being developed using hydride generation ICPMS. These elements must be first transformed into hydride-forming oxidation states. This is particularly challenging for selenium and antimony because selenium is susceptible to reduction to the non-hydride-forming elemental state and antimony requires strong reducing conditions. The effectiveness of three reducing agents (KI, thiourea, cysteine) is studied. A comparison is made between addition of reducing agent to the sample and addition of KI to the NaBH 4 solution. Best results were obtained with the latter approach. (author)

Gamma-ray irradiation and post-irradiation at room and elevated temperature response of pMOS dosimeters with thick gate oxides

Directory of Open Access Journals (Sweden)

Pejović Momčilo M.

2011-01-01

Full Text Available Gamma-ray irradiation and post-irradiation response at room and elevated temperature have been studied for radiation sensitive pMOS transistors with gate oxide thickness of 100 and 400 nm, respectively. Their response was followed based on the changes in the threshold voltage shift which was estimated on the basis of transfer characteristics in saturation. The presence of radiation-induced fixed oxide traps and switching traps - which lead to a change in the threshold voltage - was estimated from the sub-threshold I-V curves, using the midgap technique. It was shown that fixed oxide traps have a dominant influence on the change in the threshold voltage shift during gamma-ray irradiation and annealing.

Irradiation behavior evaluation of oxide dispersion strengthened ferritic steel cladding tubes irradiated in JOYO

Energy Technology Data Exchange (ETDEWEB)

Yamashita, Shinichiro, E-mail: yamashita.shinichiro@jaea.go.jp; Yano, Yasuhide; Ohtsuka, Satoshi; Yoshitake, Tsunemitsu; Kaito, Takeji; Koyama, Shin-ichi; Tanaka, Kenya

2013-11-15

Irradiation behavior of ODS steel cladding tubes was evaluated for the further progress in understanding of the neutron-irradiation effects on ODS steel. Two types of ODS (9Cr–ODS{sub F}/M, 12Cr–ODS{sub F}) steel cladding tubes with differences in basic compositions and matrix phases were irradiated in JOYO. Post-irradiation examination data concerning hardness, ring tensile property, and microstructure were obtained. Hardness measurement after irradiation showed that there was an apparent irradiation temperature dependence on hardness for 9Cr–ODS{sub F}/M steel whereas no distinct temperature dependence for 12Cr–ODS{sub F} steel. Also, there was no significant change in tensile strengths after irradiation below 923 K, but those above 1023 K up to 6.6 × 10{sup 26} n/m{sup 2} (E > 0.1 MeV) were decreased by about 20%. TEM observations showed that the radiation-induced defect cluster formation during irradiation was suppressed because of high density sink site for defect such as initially-existed dislocation, and precipitate interfaces. In addition, oxide particles were stable up to the maximum doses of this irradiation test.

17O NMR investigation of oxidative degradation in polymers under γ-irradiation

International Nuclear Information System (INIS)

ALAM, TODD M.; CELINA, MATHIAS C.; ASSINK, ROGER A.; CLOUGH, ROGER LEE; GILLEN, KENNETH T.

2000-01-01

The γ-irradiated-oxidation of pentacontane (C 50 H 102 ) and the polymer polyisoprene was investigated as a function of oxidation level using 17 O nuclear magnetic resonance (NMR) spectroscopy. It is demonstrated that by using 17 O labeled O 2 gas during the γ-irradiation process, details about the oxidative degradation mechanisms can be directly obtained from the analysis of the 17 O NMR spectra. Production of carboxylic acids is the primary oxygen-containing functionality during the oxidation of pentacontane, while ethers and alcohols are the dominant oxidation product observed for polyisoprene. The formation of ester species during the oxidation process is very minor for both materials, with water also being produced in significant amounts during the radiolytic oxidation of polyisoprene. The ability to focus on the oxidative component of the degradation process using 17 O NMR spectroscopy demonstrates the selectivity of this technique over more conventional approaches

Quantitative measurements of oxidative stress in mouse skin induced by X-ray irradiation

International Nuclear Information System (INIS)

Chi, Cuiping; Tanaka, Ryoko; Okuda, Yohei; Ikota, Nobuo; Ozawa, Toshihiko; Anzai, Kazunori; Yamamoto, Haruhiko; Urano, Shiro

2005-01-01

To find efficient methods to evaluate oxidative stress in mouse skin caused by X-ray irradiation, several markers and methodologies were examined. Hairless mice were irradiated with 50 Gy X-rays and skin homogenates or skin strips were prepared. Lipid peroxidation was measured using the skin homogenate as the level of thiobarbituric acid reactive substances. The level of lipid peroxidation increased with time after irradiation and was twice that of the control at 78 h. Electron spin resonance (ESR) spectra of skin strips showed a clear signal for the ascorbyl radical, which increased with time after irradiation in a manner similar to that of lipid peroxidation. To measure levels of glutathione (GSH) and its oxidized forms (GSSG) simultaneously, two high performance liquid chromatography (HPLC) methods, sample derivatization with 1-fluoro-2,4-dinitrobenzene and detection with a UV detector (method A) and no derivatization and detection with an electrochemical detector (method B), were compared and the latter was found to be better. No significant change was observed within 24 h after irradiation in the levels of GSH and GSSG measured by method B. The GSH/GSSG ratio may be a less sensitive parameter for the evaluation of acute oxidative stress caused by X-ray irradiation in the skin. Monitoring the ascorbyl radical seems to be a good way to evaluate oxidative stress in skin in vivo. (author)

Site-specific nucleation and controlled growth of a vertical tellurium nanowire array for high performance field emitters

International Nuclear Information System (INIS)

Safdar, Muhammad; Zhan Xueying; Mirza, Misbah; Wang Zhenxing; Sun Lianfeng; He Jun; Niu Mutong; Zhang Jinping; Zhao Qing

2013-01-01

We report the controlled growth of highly ordered and well aligned one-dimensional tellurium nanostructure arrays via a one-step catalyst-free physical vapor deposition method. The density, size and fine structures of tellurium nanowires are systematically studied and optimized. Field emission measurement was performed to display notable dependence on nanostructure morphologies. The ordered nanowire array based field emitter has a turn-on field as low as 3.27 V μm −1 and a higher field enhancement factor of 3270. Our finding offers the possibility of controlling the growth of tellurium nanowire arrays and opens up new means for their potential applications in electronic devices and displays. (paper)

UV irradiation-induced methionine oxidation in human skin keratins: Mass spectrometry-based non-invasive proteomic analysis.

Science.gov (United States)

Lee, Seon Hwa; Matsushima, Keita; Miyamoto, Kohei; Oe, Tomoyuki

2016-02-05

Ultraviolet (UV) radiation is the major environmental factor that causes oxidative skin damage. Keratins are the main constituents of human skin and have been identified as oxidative target proteins. We have recently developed a mass spectrometry (MS)-based non-invasive proteomic methodology to screen oxidative modifications in human skin keratins. Using this methodology, UV effects on methionine (Met) oxidation in human skin keratins were investigated. The initial screening revealed that Met(259), Met(262), and Met(296) in K1 keratin were the most susceptible oxidation sites upon UVA (or UVB) irradiation of human tape-stripped skin. Subsequent liquid chromatography/electrospray ionization-MS and tandem MS analyses confirmed amino acid sequences and oxidation sites of tryptic peptides D(290)VDGAYMTK(298) (P1) and N(258)MQDMVEDYR(267) (P2). The relative oxidation levels of P1 and P2 increased in a time-dependent manner upon UVA irradiation. Butylated hydroxytoluene was the most effective antioxidant for artifactual oxidation of Met residues. The relative oxidation levels of P1 and P2 after UVA irradiation for 48 h corresponded to treatment with 100mM hydrogen peroxide for 15 min. In addition, Met(259) was oxidized by only UVA irradiation. The Met sites identified in conjunction with the current proteomic methodology can be used to evaluate skin damage under various conditions of oxidative stress. We demonstrated that the relative Met oxidation levels in keratins directly reflected UV-induced damages to human tape-stripped skin. Human skin proteins isolated by tape stripping were analyzed by MS-based non-invasive proteomic methodology. Met(259), Met(262), and Met(296) in K1 keratin were the most susceptible oxidation sites upon UV irradiation. Met(259) was oxidized by only UVA irradiation. Quantitative LC/ESI-SRM/MS analyses confirmed a time-dependent increase in the relative oxidation of target peptides (P1 and P2) containing these Met residues, upon UVA irradiation

Quercetin oxidation by horseradish peroxidase: The effect of UV-B irradiation

Directory of Open Access Journals (Sweden)

Savić Saša R.

2013-01-01

Full Text Available Horseradish peroxidase (HRP, a highly-investigated member of the peroxidase family has been known, among many other biological activities, to catalyze the oxidation of flavonoids and phenolic substrates overall, including quercetin. On the other hand, quercetin is very well known for its antioxidant activities, which in the case of UV external radiation is exibited partly in a preventive manner since it is an excellent UV-absorber. Therefore the aim of this investigation is to study quercetin oxidation by HRP in phosphate buffer under the conditions of UV-stress, i.e. continuous, prolonged UV-B irradiation. The results show that while UV-B irradiation affects the activity of HRP, and the overal rate of quercetin oxidation by HRP, it probably has very little effect on it for longer UV-B-irradiation periods (>30 min. [Acknowledgements. This work was supported by the Ministry of Education and Science of the Republic of Serbia under Project No.TR-34012 and OI-172044

Accumulation of the radionuclides in a target irradiated in the reactor of tajoura nuclear research center

International Nuclear Information System (INIS)

Abdunnobi, A.R.; Arebi, B.

1998-01-01

One of the main stages of radionuclides production in reactor is the distinguishing of a regime on target irradiation in order to acquire the sufficient activity and the purity of radioisotope required. The authors have derived formula for calculating radionuclidic accumulation on a target irradiated in the reactor operating 10 hours per day, 4 days a week during 4 weeks. The results of I-131 and other radionuclide accumulation are illustrated by a tellurium target irradiation in the reactor operating continuously or with interruptions

Schisandrin B protects against solar irradiation-induced oxidative injury in BJ human fibroblasts.

Science.gov (United States)

Chiu, Po Yee; Lam, Philip Y; Yan, Chung Wai; Ko, Kam Ming

2011-06-01

The effects of schisandrin B (Sch B) and its analogs on solar irradiation-induced oxidative injury were examined in BJ human fibroblasts. Sch B and schisandrin C (Sch C) increased cellular reduced glutathione (GSH) level and protected against solar irradiation-induced oxidative injury. The photoprotection was paralleled by decreases in the elastases-type protease activity and matrix-metalloproteinases-1 expression in solar-irradiated fibroblasts. The cytochrome P-450-mediated metabolism of Sch B or Sch C caused ROS production. The results suggest that by virtue of its pro-oxidant action and the subsequent glutathione antioxidant response, Sch B or Sch C may offer the prospect of preventing skin photo-aging. Copyright © 2011 Elsevier B.V. All rights reserved.

Dismantling and chemical characterization of spent Peltier thermoelectric devices for antimony, bismuth and tellurium recovery.

Science.gov (United States)

Balva, Maxime; Legeai, Sophie; Garoux, Laetitia; Leclerc, Nathalie; Meux, Eric

2017-04-01

Major uses of thermoelectricity concern refrigeration purposes, using Peltier devices, mainly composed of antimony, bismuth and tellurium. Antimony was identified as a critical raw material by EU and resources of bismuth and tellurium are not inexhaustible, so it is necessary to imagine the recycling of thermoelectric devices. That for, a complete characterization is needed, which is the aim of this work. Peltier devices were manually dismantled in three parts: the thermoelectric legs, the alumina plates on which remain the electrical contacts and the silicone paste used to connect the plates. The characterization was performed using five Peltier devices. It includes mass balances of the components, X-ray diffraction analysis of the thermoelectric legs and elemental analysis of each part of the device. It appears that alumina represents 45% of a Peltier device in weight. The electrical contacts are mainly composed of copper and tin, and the thermoelectric legs of bismuth, tellurium and antimony. Thermoelectric legs appear to be Se-doped Bi 2 Te 3 and (Bi 0,5 Sb 1,5 )Te 3 for n type and p type semiconductors, respectively. This work shows that Peltier devices can be considered as a copper ore and that thermoelectric legs contain high amounts of bismuth, tellurium and antimony compared to their traditional resources.

Lipid and cholesterol oxidation, color changes, and volatile compounds production in irradiated raw pork batters with different fat content

International Nuclear Information System (INIS)

Jo, Cheo Run; Byun, Myung Woo

2000-01-01

An emulsion-type product was prepared to determine the effect of irradiation on lipid and cholesterol oxidation, color change, and volatile production in raw pork with different fat content. Lipid oxidation increased with an increase in fat content or irradiation dose. Irradiated batters had higher cholesterol oxides than did non-irradiated batters, and the major cholesterol oxides formed in irradiated pork batters were 7α- and 7β- hydroxycholesterol. Hunter color a- and b-values of raw pork batters were decreased by irradiation regardless of fat content. Irradiation significantly increased the amount of volatile compounds. Although lipid oxidation of high fat products (10 and 15% fat) was higher than that of low fat products (4%), high fat products did not always produce greater amount of volatile compounds in raw pork batters. In summary, irradiation increased lipid and cholesterol oxidation, and volatile compounds production, and had detrimental effects on the color of raw pork batter under aerobic conditions

Blue light irradiation-induced oxidative stress in vivo via ROS generation in rat gingival tissue.

Science.gov (United States)

Yoshida, Ayaka; Shiotsu-Ogura, Yukako; Wada-Takahashi, Satoko; Takahashi, Shun-suke; Toyama, Toshizo; Yoshino, Fumihiko

2015-10-01

It has been reported that oxidative stress with reactive oxygen species (ROS) generation is induced by blue light irradiation to a living body. Only limited research has been reported in dental field on the dangers of blue light, mostly focusing on cytotoxicity associated with heat injury of dental pulp. We thus performed an in vivo study on oral tissue exposed to blue light. ROS generated upon blue light irradiation of flavin adenine dinucleotide were measured by electron spin resonance spectroscopy. After blue light irradiation, the palatal gingiva of Wistar rats were isolated. Collected samples were subjected to biochemical analysis of lipid peroxidation and glutathione. Singlet oxygen was generated by blue light irradiation, but was significantly quenched in an N-acetyl-L-cysteine (NAC) concentration-dependent manner. Blue light significantly accelerated oxidative stress and increased the oxidized glutathione levels in gingival tissue. These effects were also inhibited by NAC pre-administration. The results suggest that blue light irradiation at clinical levels of tooth bleaching treatment may enhance lipid peroxidation by the induction of oxidative stress and the consumption of a significant amount of intracellular glutathione. In addition, NAC might be an effective supplement for the protection of oral tissues against blue light irradiation-induced oxidative damage. Copyright © 2015 Elsevier B.V. All rights reserved.

Technological parameters and oxidative stability of irradiated wheat and corn flour

International Nuclear Information System (INIS)

Silva, Roberta Claro da

2003-01-01

Cereals are susceptible to the attack of insects and microorganisms development during storage. Researches have demonstrated the viability of the use of the irradiation technology for the preservation and reduction of these losses. The objective of this work was to evaluate the effect of different irradiation doses (0; 3; 4,5 and 6 kGy) on wheat and corn flour oxidative stability and technological quality. Physicochemical and sensory analyses were performed on the flours. The technological parameters evaluated on the wheat flour were farinogram, alveogram, falling number, and a baking experiment. The packed samples were irradiated in a commercial irradiator and stored under ambient conditions. The oxidative quality of both flours was not affected in any of the treatments, within the commercial shelf life period guaranteed by the manufacturers for non irradiated products. However, flours acid value was the analytical parameter that reflected the irradiation effect. The higher flour initial acid values were the larger the increments with storage. The 4.5 and 6 kGy treatments ha a negative effect on the technological quality of the wheat flour. The irradiated flours had their viscoelastic properties affected the higher the irradiation dose, the stronger the effect. None of the treatments affected the sensorial quality of the samples, although a metallic odor was perceived by some tasters. (author)

Physical properties of beryllium oxide - Irradiation effects

International Nuclear Information System (INIS)

Elston, J.; Caillat, R.

1958-01-01

This work has been carried out in view of determining several physical properties of hot-pressed beryllium oxide under various conditions and the change of these properties after irradiation. Special attention has been paid on to the measurement of the thermal conductivity coefficient and thermal diffusivity coefficient. Several designs for the measurement of the thermal conductivity coefficient have been achieved. They permit its determination between 50 and 300 deg. C, between 400 and 800 deg. C. Some measurements have been made above 1000 deg. C. In order to measure the thermal diffusivity coefficient, we heat a perfectly flat surface of a sample in such a way that the heat flux is modulated (amplitude and frequency being adjustable). The thermal diffusivity coefficient is deduced from the variations of temperature observed on several spots. Tensile strength; compressive strength; expansion coefficient; sound velocity and crystal parameters have been also measured. Some of the measurements have been carried out after neutron irradiation. Some data have been obtained on the change of the properties of beryllium oxide depending on the integrated neutron flux. (author) [fr

Structural changes in graphene oxide thin film by electron-beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Tyagi, Chetna, E-mail: tchetna91@gmail.com [Materials Science Group, Inter University Accelerator Centre, New Delhi 67 (India); Lakshmi, G.B.V.S.; Kumar, Sunil; Tripathi, Ambuj [Materials Science Group, Inter University Accelerator Centre, New Delhi 67 (India); Avasthi, D.K. [Amity University, Noida 201313, Uttar Pradesh (India)

2016-07-15

Although we have a whole class of 2D materials, graphene has drawn much attention for its excellent electronic, optical, thermal and mechanical properties. Recent researches have shown its large scale production by the reduction of graphene oxide either thermally, chemically or electrochemically. Although the structure of graphene oxide is inhomogeneous and hence complicated due to the presence of organic moieties e.g. epoxy, carboxylic acid, hydroxyl groups etc., its properties can be tuned by reduction according to desired application. The aim of this work is to synthesize continuous thin film of graphene oxide using commercially available graphene oxide solution and to study its reduction by 25 keV electron beam irradiation at fluences varying from 2 × 10{sup 11} to 2 × 10{sup 13} e{sup −}/cm{sup 2}. Our studies using X-ray diffraction, Raman microscopy and UV–Vis spectroscopy showed that electron-beam irradiation is an effective tool for reduction of graphene oxide and for tuning its band gap.

Effects of gamma irradiation in graphene/poly (ethylene oxide) nanocomposites

International Nuclear Information System (INIS)

Braz, Elton P.; Goncalves, Natercia Antunes; Araujo, Patricia L.B.; Araujo, Elmo S.

2013-01-01

Nanotechnology is the understanding and control of matter in dimensions between 1 and 100nm. In such small matter portions, improved or even new properties may arise, as a direct consequence of reduced size. Thus, the development of multifunctional nanomaterials is nowadays one of the main goals of the materials research field. In this context, we produced graphene sheets through ultrasound exfoliation of graphite oxide, followed by chemical reduction. Composite nanofibers of these graphene sheets with biocompatible polymer poly (ethylene oxide) (PEO) were obtained by electrospinning technique, and irradiated up to 75kGy dose to assess the effects of gamma irradiation in the molecular structure of these composite nanomaterial. Our findings showed that PEO is quite resistant to radiation damage and that the incorporation of graphene oxide has no significant influence on its radiostability. (author)

Tuning surface properties of graphene oxide quantum dots by gamma-ray irradiation

Energy Technology Data Exchange (ETDEWEB)

Lu, Shunkai; Liao, Fan, E-mail: fliao@suda.edu.cn; Wang, Tao; Zhu, Lili; Shao, Mingwang, E-mail: mwshao@suda.edu.cn

2016-07-15

Gamma-ray irradiation was employed to tune surface properties of graphene oxide quantum dots (GOQDs), such as functional groups and defect density. The GOQDs were first oxidized under γ-ray irradiation with doses ranging from 0 to 200 kGy, and then reduced under larger irradiation doses from 200 to 400 kGy. In other words, both the defect density and the number of surface functional groups increased first and then decreased along with the increasing irradiation dose. This process was confirmed with UV–visible absorption, X-ray photoelectron spectroscopy, Raman spectra and Fourier transform infrared spectra. In order to estimate their π-conjugated content, the GOQDs were served to quench the fluorescence of Rhodamine 6 G. The results showed that there existed a positive relationship between the π-conjugated content and the static quenching coefficient V{sub q}Na, which might have a potential value. - Highlights: • The conjugate extent and hydrophily of GOQDs decreased along with irradiation dose. • Gamma-ray irradiation weakens the quenching effect of GOQDs. • Quenching mechanism is a combination of dynamic and static quenching.

Study of the stability of the nanometer-sized oxides dispersed in ODS steels under ion irradiations

International Nuclear Information System (INIS)

Lescoat, M.-L.

2012-01-01

Oxide Dispersion Strengthened (ODS) Ferritic-Martensitic (FM) alloys are expected to play an important role as cladding materials in Generation IV sodium fast reactors operating in extreme temperature (400-500 C) and irradiation conditions (up to 200 dpa). Since nano-oxides give ODS steels their high temperature strength, the stability of these particles is an important issue. The present study evaluates the radiation response of nano-oxides by the use of in-situ and ex-situ ion irradiations performed on both Fe18Cr1W0,4Ti +0,3 Y 2 O 3 and Fe18Cr1W0,4Ti + 0.3 MgO ODS steels. In particular, the results showed that Y-Ti-O nano-oxides are quite stable under very high irradiation dose, namely 219 dpa at 500 C, and that the oxide interfacial structures are likely playing an important role on the behavior under irradiation (oxide stability and point defect recombination. (author) [fr

Packaging and irradiation effects on lipid oxidation and volatiles in pork patties

International Nuclear Information System (INIS)

Ahn, D.U.; Olson, D.G.; Lee, J.I.; Jo, C.; Wu, C.; Chen, X.

1998-01-01

Raw-meat patties were prepared from three pork muscles, irradiated in different packaging environments, and stored for 0 or 3 days before cooking. Lipid oxidation by-products were formed in the raw meat during storage and the baseline lipid oxidation data of raw meat was used to measure the progression of lipid oxidation after cooking. Thiobarbituric acid-reactive substances (TBARS) and volatiles data indicated that preventing oxygen exposure after cooking was more important for cooked meat quality than packaging, irradiation, or storage conditions of raw meat. Propanal, pentanal, hexanal, 1-pentanol, and total volatiles correlated highly (P 0.01) with TBARS values of cooked meat. Hexanal and total volatiles represented the lipid oxidation status better than any other individual volatile components

Selenium Se and tellurium Te

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for determining selenium and tellurium in various objects are presented. The bichromatometric determination of Te in cadmium, zinc and mercury tellurides is based on oxidation of Te(4) to (6) in H 2 SO 4 with potassium bichromate. In steels, Te is determined photometrically with the aid of KI. The determination is hindered by Fe(3), Cu(2), Bi(3) and Se(4) ions, which must be separated. The extraction-photometric determination of Te in native sulfur is carried out with the aid of 5-mercapto-3-(naphthyl-2)-1,3,4-thiadiazolthione-2 (pH=4.8-5.0). The dyed complex is readily extracted with chloroform and benzene. The spectrophotometric determination of Te in selenium is performed with the aid of 3,5-diphenylpyrazoline-1-dithiocarbamate of sodium. Te is determined in commercial indium, arsenic and their semiconductor compounds photometrically with the aid of copper diethyldithiocarbamate. The method permits determining 5x10 -5 % Te in a weighed amount of 0.5 g. The chloride complex of Te(4) with diantipyriodolpropylmethane is quantitatively extracted with dichloroethane from hydrochloric acid solutions. Thus, any amounts of Te can be separated from Se and determined photometrically. The extraction-photometric determination of Te in commercial lead and bismuth is carried out with the aid of pyrazolone derivatives, in commercial copper with the aid of diantipyridolpropylmethane, and in ores (more than 0.01% Te) with the aid of bismuthol 2. Also described is the extraction-polarographic determination of Te in sulfide ores

Stability under irradiation of a fine dispersion of oxides in a ferritic matrix; Stabilite sous irradiation de particules d'oxydes finement dispersees dans des alliages ferritiques

Energy Technology Data Exchange (ETDEWEB)

Monnet, I

1999-07-01

Oxide dispersion strengthened (ODS) ferritic-martensitic steels are being considered for high temperature, high fluence nuclear applications, like fuel pin cladding in Fast Breeder Reactors. ODS alloys offer improved out of pile strength characteristics at temperature above 550 deg.C and ferritic-martensitic matrix is highly swelling resistant. A clad in an ODS ferritic steel, call DY (Fe-13Cr-1,5Mo+TiO{sub 2}+Y{sub 2}O{sub 3}) has been irradiated in the experimental reactor Phenix. Under irradiation oxide dissolution occurs. Microstructural observations indicated that oxide evolution is correlated with the dose and consist in four phenomena: the interfaces of oxide particles with the matrix become irregular, the uniform distribution of the finest oxide (< 20 nm) disappear, the modification of oxide composition, and a halo of fine oxides appear around the larger oxides. The use of such a material requires a study of oxide stability under irradiation, since the oxide particles provide the desired mechanical properties. The study is based on two types of alloys, the DY and four ferritic steels Fe-9Cr-1Mo reinforced by Al{sub 2}O{sub 3}, Y{sub 2}O{sub 3}, MgO or MgAl{sub 2}O{sub 4}. These materials were irradiated with charged particles in order to gain a better understanding of the mechanisms of dissolution. Irradiation with 1 MeV Helium does not induce any modification, neither in the chemical modification of the particles nor in their spatial and size distribution. Since most of the energy of helium ions is lost by inelastic interaction, this result proves that this kind of interaction does not induce oxide dissolution. Irradiation with 1 MeV or 1.2 MeV electrons leads to a significant dissolution with a radius decrease proportional to the dose. These experiments prove that oxide dissolution can be induced by Frenkel pairs alone, provided that metallic atoms are displaced. The comparison between irradiation with ions (displacements cascades) and electrons (Frenkel

Tellurium stable isotope fractionation in chondritic meteorites and some terrestrial samples

Science.gov (United States)

Fehr, Manuela A.; Hammond, Samantha J.; Parkinson, Ian J.

2018-02-01

New methodologies employing a 125Te-128Te double-spike were developed and applied to obtain high precision mass-dependent tellurium stable isotope data for chondritic meteorites and some terrestrial samples by multiple-collector inductively coupled plasma mass spectrometry. Analyses of standard solutions produce Te stable isotope data with a long-term reproducibility (2SD) of 0.064‰ for δ130/125Te. Carbonaceous and enstatite chondrites display a range in δ130/125Te of 0.9‰ (0.2‰ amu-1) in their Te stable isotope signature, whereas ordinary chondrites present larger Te stable isotope fractionation, in particular for unequilibrated ordinary chondrites, with an overall variation of 6.3‰ for δ130/125Te (1.3‰ amu-1). Tellurium stable isotope variations in ordinary chondrites display no correlation with Te contents or metamorphic grade. The large Te stable isotope fractionation in ordinary chondrites is likely caused by evaporation and condensation processes during metamorphism in the meteorite parent bodies, as has been suggested for other moderately and highly volatile elements displaying similar isotope fractionation. Alternatively, they might represent a nebular signature or could have been produced during chondrule formation. Enstatite chondrites display slightly more negative δ130/125Te compared to carbonaceous chondrites and equilibrated ordinary chondrites. Small differences in the Te stable isotope composition are also present within carbonaceous chondrites and increase in the order CV-CO-CM-CI. These Te isotope variations within carbonaceous chondrites may be due to mixing of components that have distinct Te isotope signatures reflecting Te stable isotope fractionation in the early solar system or on the parent bodies and potentially small so-far unresolvable nucleosynthetic isotope anomalies of up to 0.27‰. The Te stable isotope data of carbonaceous and enstatite chondrites displays a general correlation with the oxidation state and hence might

Transmission electron microscopy of oxide dispersion strengthened (ODS) molybdenum: effects of irradiation on material microstructure

International Nuclear Information System (INIS)

Baranwal, R.; Burke, M.G.

2003-01-01

Oxide dispersion strengthened (ODS) molybdenum has been characterized using transmission electron microscopy (TEM) to determine the effects of irradiation on material microstructure. This work describes the results-to-date from TEM characterization of unirradiated and irradiated ODS molybdenum. The general microstructure of the unirradiated material consists of fine molybdenum grains (< 5 (micro)m average grain size) with numerous low angle boundaries and isolated dislocation networks. 'Ribbon'-like lanthanum oxides are aligned along the working direction of the product form and are frequently associated with grain boundaries, serving to inhibit grain boundary and dislocation movement. In addition to the 'ribbons', discrete lanthanum oxide particles have also been detected. After irradiation, the material is characterized by the presence of nonuniformly distributed large (∼ 20 to 100 nm in diameter), multi-faceted voids, while the molybdenum grain size and oxide morphology appear to be unaffected by irradiation

Modelling the chemical behaviour of tellurium species in the reactor pressure vessel and the reactor cooling system under severe accident conditions

International Nuclear Information System (INIS)

Alonso, A.; Gonzalez, C.

1991-07-01

This state of the art report contains information on the behaviour of tellurium and its compounds in the reactor pressure vessel and the reactor coolant system under light water reactor severe accident conditions. To characterise tellurium behaviour, it is necessary the previous knowledge of the species of tellurium released from the core, and simultaneity of its release with that of other materials which can alter the transport, for instance, control rod and structural materials. Release and transport experiments have been reviewed along with the models implemented in the codes which are used in the international community: TRAPMELT, RAFT, VICTORIA and SOPHIE. From the experiments, it can be concluded that other species different to Te 2 , such as tin telluride and cesium telluride, may be released from the fuel. That is why they must be considered in the transport phenomena. There is also experimental evidence of the strong interaction of Te 2 with Inconel 600 and stainless steel of the pipe walls and structures, however this strong interaction is in competition with the interaction of tellurium with aerosols, which under severe accident conditions may represent an area greater than that of the primary system. It is for the absence of significant tellurium species in the transport models, and also for the interaction of tellurium with aerosols, for which some codes show the greatest deficiencies

Potential for improved extraction of tellurium as a byproduct of current copper mining processes

Science.gov (United States)

Hayes, S. M.; Spaleta, K. J.; Skidmore, A. E.

2016-12-01

Tellurium (Te) is classified as a critical element due to its increasing use in high technology applications, low average crustal abundance (3 μg kg-1), and primary source as a byproduct of copper extraction. Although Te can be readily recovered from copper processing, previous studies have estimated a 4 percent extraction efficiency, and few studies have addressed Te behavior during the entire copper extraction process. The goals of the present study are to perform a mass balance examining Te behavior during copper extraction and to connect these observations with mineralogy of Te-bearing phases which are essential first steps in devising ways to optimize Te recovery. Our preliminary mass balance results indicate that less than 3 percent of Te present in copper ore is recovered, with particularly high losses during initial concentration of copper ore minerals by flotation. Tellurium is present in the ore in telluride minerals (e.g., Bi-Te-S phases, altaite, and Ag-S-Se-Te phases identified using electron microprobe) with limited substitution into sulfide minerals (possibly 10 mg kg-1 Te in bulk pyrite and chalcopyrite). This work has also identified Te accumulation in solid-phase intermediate extraction products that could be further processed to recover Te, including smelter dusts (158 mg kg-1) and pressed anode slimes (2.7 percent by mass). In both the smelter dusts and anode slimes, X-ray absorption spectroscopy indicates that about two thirds of the Te is present as reduced tellurides. In anode slimes, electron microscopy shows that the remaining Te is present in an oxidized form in a complex Te-bearing oxidate phase also containing Pb, Cu, Ag, As, Sb, and S. These results clearly indicate that more efficient, increased recovery of Te may be possible, likely at minimal expense from operating copper processing operations, thereby providing more Te for manufacturing of products such as inexpensive high-efficiency solar panels.

ELECTROCHEMICAL STUDY OF RHENIUM-TELLURIUM-COPPER SYSTEM

OpenAIRE

E.A.Salakhova*1, D.B.Tagiyev2, P.E.Kalantarova3 and A.M.Askerova4

2017-01-01

The formation of the triple alloys Re-Te-Cu on the platinum electrode at volt amperemetric cycling has been studied. The investigation was carried out from chloride acidic solution containing tellurium acid, potassium perrhenate, chloride copper. The kinetics of the processes was controlled using the measurements by the method of cyclic volt-amperometry on the device İVİUMSTAT. For the analysis of composition and structure the methods of XRD (X-ray diffraction analysis) were used, and the inv...

Light water reactor mixed-oxide fuel irradiation experiment

International Nuclear Information System (INIS)

Hodge, S.A.; Cowell, B.S.; Chang, G.S.; Ryskamp, J.M.

1998-01-01

The United States Department of Energy Office of Fissile Materials Disposition is sponsoring and Oak Ridge National Laboratory (ORNL) is leading an irradiation experiment to test mixed uranium-plutonium oxide (MOX) fuel made from weapons-grade (WG) plutonium. In this multiyear program, sealed capsules containing MOX fuel pellets fabricated at Los Alamos National Laboratory (LANL) are being irradiated in the Advanced Test Reactor (ATR) at the Idaho National Engineering and Environmental Laboratory (INEEL). The planned experiments will investigate the utilization of dry-processed plutonium, the effects of WG plutonium isotopics on MOX performance, and any material interactions of gallium with Zircaloy cladding

Low-temperature formation of high-quality gate oxide by ultraviolet irradiation on spin-on-glass

International Nuclear Information System (INIS)

Usuda, R.; Uchida, K.; Nozaki, S.

2015-01-01

Although a UV cure was found to effectively convert a perhydropolysilazane (PHPS) spin-on-glass film into a dense SiO x film at low temperature, the electrical characteristics were never reported in order to recommend the use of PHPS as a gate-oxide material that can be formed at low temperature. We have formed a high-quality gate oxide by UV irradiation on the PHPS film, and obtained an interface midgap trap density of 3.4 × 10 11  cm −2 eV −1 by the UV wet oxidation and UV post-metallization annealing (PMA), at a temperature as low as 160 °C. In contrast to the UV irradiation using short-wavelength UV light, which is well known to enhance oxidation by the production of the excited states of oxygen, the UV irradiation was carried out using longer-wavelength UV light from a metal halide lamp. The UV irradiation during the wet oxidation of the PHPS film generates electron-hole pairs. The electrons ionize the H 2 O molecules and facilitate dissociation of the molecules into H and OH − . The OH − ions are highly reactive with Si and improve the stoichiometry of the oxide. The UV irradiation during the PMA excites the electrons from the accumulation layer, and the built-in electric field makes the electron injection into the oxide much easier. The electrons injected into the oxide recombine with the trapped holes, which have caused a large negative flat band voltage shift after the UV wet oxidation, and also ionize the H 2 O molecules. The ionization results in the electron stimulated dissociation of H 2 O molecules and the decreased interface trap density

Low-temperature formation of high-quality gate oxide by ultraviolet irradiation on spin-on-glass

Energy Technology Data Exchange (ETDEWEB)

Usuda, R.; Uchida, K.; Nozaki, S., E-mail: nozaki@ee.uec.ac.jp [Graduate School of Informatics and Engineering, The University of Electro-Communications, 1-5-1 Chofugaoka, Chofu-shi, Tokyo 182-1515 (Japan)

2015-11-02

Although a UV cure was found to effectively convert a perhydropolysilazane (PHPS) spin-on-glass film into a dense SiO{sub x} film at low temperature, the electrical characteristics were never reported in order to recommend the use of PHPS as a gate-oxide material that can be formed at low temperature. We have formed a high-quality gate oxide by UV irradiation on the PHPS film, and obtained an interface midgap trap density of 3.4 × 10{sup 11 }cm{sup −2} eV{sup −1} by the UV wet oxidation and UV post-metallization annealing (PMA), at a temperature as low as 160 °C. In contrast to the UV irradiation using short-wavelength UV light, which is well known to enhance oxidation by the production of the excited states of oxygen, the UV irradiation was carried out using longer-wavelength UV light from a metal halide lamp. The UV irradiation during the wet oxidation of the PHPS film generates electron-hole pairs. The electrons ionize the H{sub 2}O molecules and facilitate dissociation of the molecules into H and OH{sup −}. The OH{sup −} ions are highly reactive with Si and improve the stoichiometry of the oxide. The UV irradiation during the PMA excites the electrons from the accumulation layer, and the built-in electric field makes the electron injection into the oxide much easier. The electrons injected into the oxide recombine with the trapped holes, which have caused a large negative flat band voltage shift after the UV wet oxidation, and also ionize the H{sub 2}O molecules. The ionization results in the electron stimulated dissociation of H{sub 2}O molecules and the decreased interface trap density.

Inhibition effect on lipid oxidation of irradiated pork by adding hawthorn flavonoid extract

International Nuclear Information System (INIS)

Wang Xiaoming; Liu Chao; Cao Lei; Li Kexi

2011-01-01

The antioxidant activity of hawthorn flavonoid extract and its inhibition effect on irradiated pork lipid oxidant were investigated. The results showed that hawthorn flavonoids had efficient scavenging effect on DPPH free radicals (DPPH ·), and the scavenging rate reached 56% while 2 ml of 0.035 mg/ml hawthorn flavonoid extract was added. Hawthorn flavonoid extract can inhibition the lipid oxidation of irradiated pork effectively and it showed a stronger inhibition ability while the hawthorn flavonoid extract were used together with Vc. It is concluded that can decrease the lipid oxidation of pork, hawthorn flavonoid extract is a remarkable natural antioxidant. (authors)

Acousto-optic measurements of ultrasound attenuation in tellurium dioxide crystal

International Nuclear Information System (INIS)

Voloshinov, V. B.; Lemyaskina, E. A.

1996-01-01

The paper is devoted to experimental investigation of ultrasound propagation in tellurium dioxide monocrystal. In particular, attenuation of slow shear acoustic modes in the crystal was measured. The measurements were performed by acousto-optic methods using probing of acoustic column by a laser beam. The paper describes measurements of acoustic attenuation coefficient for slow shear ultrasonic waves propagating at an angle =4.5 O with respect to the (110) direction in the (110) plane. The investigation was made at acoustic frequency f = 100 MHz with pulsed acoustic waves and with an optical beam of a He-Ne laser. It is found that the attenuation coefficient is α = 0.57 cm -1 ± 15 %. The attenuation at acoustic frequencies f ≥ 100 MHz influences performance characteristics of acousto-optical devices based on tellurium dioxide. As proved, spectral resolution of a quasicollinear acoustooptic filter decreases by a factor of 2 compared to a case of the attenuation absence. (authors)

Solvent Extraction of Tellurium from Chloride Solutions Using Tri-n-butyl Phosphate: Conditions and Thermodynamic Data

Directory of Open Access Journals (Sweden)

Dongchan Li

2014-01-01

Full Text Available The extractive separation of tellurium (IV from hydrochloric acid media with tri-n-butyl phosphate (TBP in kerosene was investigated. The dependence on the extraction of tellurium species, concentrations of tellurium and TBP, extraction time and stage, organic/aqueous ratio, and interferences from coexist metallic ions were examined and are discussed. Besides, the stripping agent and stripping time were also studied. It was found that the extraction reaction corresponds to the neutral complex formation mechanism and the extracted species is TeCl4·3TBP and that the extraction process is exothermic. The thermodynamic parameters of enthalpy ΔH, entropy ΔS, and free energy ΔG of the extraction process were evaluated at −26.2 kJ·mol−1, −65.6 J·mol−1·K−1, and −7.0 kJ·mol−1, respectively at 293 K.

Irradiation behavior of uranium oxide - Aluminum dispersion fuel

International Nuclear Information System (INIS)

Hofman, Gerard L.; Rest, Jeffrey; Snelgrove, James L.

1996-01-01

An oxide version of the DART code has been generated in order to assess the irradiation behavior of UO 2 -Al dispersion fuel. The aluminum-fuel interaction models were developed based on U 3 O 8 -Al irradiation data. Deformation of the fuel element occurs due to fuel particle swelling driven by both solid and gaseous fission products and as a consequence of the interaction between the fuel particles and the aluminum matrix. The calculations show that, with the assumption that the correlations derived from U 3 O 8 are valid for UO 2 , the LEU UO 2 -Al with a 42% fuel volume loading (4 g U/cm 3 ) irradiated at fuel temperatures greater than 413 K should undergo breakaway swelling at core burnups greater than about 1.12 x 10 27 fissions m -3 (∼63% 235 U burnup). (author)

Irradiation behavior of uranium oxide-aluminum dispersion fuel

International Nuclear Information System (INIS)

Hofman, G.L.; Rest, J.; Snelgrove, J.L.

1996-01-01

An oxide version of the DART code has been generated in order to assess the irradiation behavior of UO 2 -Al dispersion fuel. The aluminum-fuel interaction models were developed based on U 3 O 8 -Al irradiation data. Deformation of the fuel element occurs due to fuel particle swelling driven by both solid and gaseous fission products, as well as a consequence of the interaction between the fuel particles and the aluminum matrix. The calculations show, that with the assumption that the correlations derived from U 3 O 8 are valid for UO 2 , the LEU UO 2 -Al with a 42% fuel volume loading (4 gm/cc) irradiated at fuel temperatures greater than 413 K should undergo breakaway swelling at core burnups greater than about 1.12 x 10 27 fissions m -3 (∼ 63% 235 U burnup)

Experimental and thermodynamic evaluation of the melting behavior of irradiated oxide fuels

International Nuclear Information System (INIS)

Adamson, M.G.; Aitken, E.A.; Caputi, R.W.

1985-01-01

Onset of melting is an important performance limit for irradiated UO 2 and UO 2 -based nuclear reactor fuels. Melting (solidus) temperatures are reasonably well known for starting fuel materials such as UO 2 and (U,PU)O 2 , however the influence of burnup on oxide fuel melting behavior continues to represent an area of considerable uncertainty. In this paper we report the results of a variety of melting temperature measurements on pseudo-binary fuel-fissia mixtures such as UO 2 -PUO 2 , UO 2 -CeO 2 , UO 2 -BaO, UO 2 -SrO, UO 2 -BaZrO 3 and UO 2 -SrZrO 3 . These measurements were performed using the thermal arrest technique on tungsten-encapsulated specimens. Several low melting eutectics, the existence of which had previously been inferred from post-irradiation examinations of high burnup mixed oxide fuels, were characterized in the course of the investigation. Also, an assessment of melting temperature changes in irradiated oxide fuels due to the production and incorporation of soluble oxidic fission products was performed by application of solution theory to the available pseudo-binary phase diagram data. The results of this assessment suggest that depression of oxide fuel solidus temperatures by dissolved fission products is substantially less than that indicated by earlier experimental studies. (orig.)

Thermoluminescent response of aluminium oxide thin films subject to gamma irradiation

Energy Technology Data Exchange (ETDEWEB)

Arrieta, A.; Escobar A, L.; Camps, E.; Villagran, E.; Gonzalez, P.R

2006-07-01

The thermoluminescent (TL) properties of amorphous aluminium oxide thin films (thicknesses as low as 0.3 {mu}m) subjected to gamma (Co-60) irradiation are reported. Aluminium oxide thin films were prepared by laser ablation from an Al{sub 2}O{sub 3} target using a Nd: YAG laser with emission at the fundamental line. The films were exposed to gamma radiation (Co-60) in order to study their TL response. Thermoluminescence glow curves exhibited two peaks at 110 and 176 C. The high temperature peak shows good stability and 30% fading in the first 5 days after irradiation. A linear relationship between absorbed dose and the thermoluminescent response for doses span from 150 mGy to 100 Gy was observed. These results suggest that aluminium oxide thin films are suitable for detection and monitoring of gamma radiation. (Author)

Coupling ultraviolet light and ultrasound irradiation with Conductive-Diamond Electrochemical Oxidation for the removal of progesterone

International Nuclear Information System (INIS)

Vidales, María J. Martín de; Barba, Silvia; Sáez, Cristina; Cañizares, Pablo; Rodrigo, Manuel A.

2014-01-01

Highlights: • Single sonolysis and photolysis technologies entail a slight progesterone removal and nil mineralization. • Synergistic effects of irradiating UV light and US are clearly observed in the oxidation rate. • The energy required by CDSEO and CDSPEO prevents against their application. • CDSEO mainly favors the mass transfer of organics to the conductive-diamond surface. • CDPEO promotes the formation of radicals in the bulk solution. - Abstract: This work focusses on the improvement of the efficiency of Conductive Diamond Electrochemical Oxidation (CDEO) by coupling US and UV irradiation in the degradation of progesterone from wastewater. Results show that CDEO is a promising technology for the degradation of progesterone, just the opposite of that observed for single sonolysis and photolysis technologies, which only entail a slight removal of progesterone and nil mineralization. Coupling UV light and US irradiations with CDEO seems to have a very positive effect, improving results obtained by single CDEO very significantly. Conductive Diamond Sono Electrochemical Oxidation (CDSEO) mainly seems to improve the transfer of pollutants to the conductive-diamond surface, while Conductive Diamond Photo Electrochemical Oxidation (CDPEO) seems to promote the formation of radicals from oxidants produced electrochemically. Soft oxidation conditions are obtained with the single application of both irradiation technologies, whereas an efficient mineralization is attained with CDEO, CDSEO, CDPEO and Conductive Diamond Sono-Photo Electrochemical Oxidation (CDSPEO). However, the high energy demands of US irradiation technologies advices against the use of CDSEO and CDSPEO

The anti-inflammatory effects of the tellurium redox modulating compound, AS101, are associated with regulation of NFκB signaling pathway and nitric oxide induction in macrophages

Directory of Open Access Journals (Sweden)

Sredni Benjamin

2010-01-01

Full Text Available Abstract Background LPS-activated macrophages produce mediators which are involved in inflammation and tissue injury, and especially those associated with endotoxic shock. The non toxic tellurium compound ammonium tri-chloro(dioxoethylene-O,O'-tellurate, AS101, has been recently shown to exert profound anti-inflammatory properties in animal models, associated with its Te(IV redox chemistry. This study explores the anti-inflammatory properties of AS101 with respect to modulation of inflammatory cytokines production and regulation of iNOS transcription and expression in activated macrophages via targeting the NFkB complex. Results AS101 decreased production of IL-6 and in parallel down-regulated LPS-induced iNOS expression and NO secretion by macrophages. AS101 reduced IkB phosphorylation and degradation, and reduced NFkB nuclear translocalization, albeit these effects were exerted at different kinetics. Chromatin immunoprecipitation assays showed that AS101 treatment attenuated p50-subunit ability to bind DNA at the NFkB consensus site in the iNOS promotor following LPS induction. Conclusions Besides AS101, the investigation of therapeutic activities of other tellurium(IV compounds is scarce in the literature, although tellurium is the fourth most abundant trace element in the human body. Since IKK and NFkB may be regulated by thiol modifications, we may thus envisage, inview of our integrated results, that Te(IV compounds, may have important roles in thiol redox biological activity in the human body and represent a new class of anti-inflammatory compounds.

First example of a high-level correlated calculation of the indirect spin-spin coupling constants involving tellurium

DEFF Research Database (Denmark)

Rusakov, Yury Yu; Krivdin, Leonid B.; Østerstrøm, Freja From

2013-01-01

This paper documents a very first example of a high-level correlated calculation of spin-spin coupling constants involving tellurium taking into account relativistic effects, vibrational corrections and solvent effects for the medium sized organotellurium molecules. The 125Te-1H spin-spin coupling...... constants of tellurophene and divinyl telluride were calculated at the SOPPA and DFT levels in a good agreement with experiment. A new full-electron basis set av3z-J for tellurium derived from the "relativistic" Dyall's basis set, dyall.av3z, and specifically optimized for the correlated calculations...... of spin-spin coupling constants involving tellurium, was developed. The SOPPA methods show much better performance as compared to 15 those of DFT, if relativistic effects calculated within the ZORA scheme are taken into account. Vibrational and solvent corrections are next to negligible, while...

Hole centers in γ-irradiated, oxidized Al2O3

International Nuclear Information System (INIS)

Lee, K.H.; Holmberg, G.E.; Crawford, J.H. Jr.

1976-01-01

ESR observations of centers with S = 1/2, g approximately equal to 2, S = 1, g approximately equal to 2 have been made at 77 K on oxidized Al 2 O 3 after γ-irradiation at 30 0 C. From the radiation growth data, it is shown that the S = 1/2 centers are precursors of the S = 1 centers. In addition, when the S = 1 centers anneal out at about 110 0 C, the S = 1/2 centers reappear and eventually anneal out at about 260 0 C. Previously Gamble (Gamble, F.T.; Ph.D. Thesis, U. of Connecticut (1963)) and Cox (Cox, R.T.; Ph.D. Thesis, U. of Grenoble (1972) unpublished), respectively, observed S = 1/2 and S = 1 paramagnetic centers in electron-irradiated nominally pure Al 2 O 3 and γ-irradiated, oxidized, titanium-doped Al 2 O 3 . The models proposed for these centers were one hole and two holes trapped on oxygen ions adjacent to Al 3+ vacancies. Our results further substantiate these models. (author)

A Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

OpenAIRE

Berman, G. P.; Doolen, G. D.; Tsifrinovich, V. I.

2000-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines the well-developed silicon technology with expected advances in MRFM.

Ion irradiation studies of oxide ceramics

International Nuclear Information System (INIS)

Zinkle, S.J.

1988-01-01

This paper presents the initial results of an investigation of the depth-dependent microstructures of three oxide ceramics following ion implantation to moderate doses. The implantations were performed using ion species that occur as cations in the target material; for example, Mg + ions were used for MgO and MgAl 2 O 4 (spinel) irradiations. This minimized chemical effects associated with the implantation and allowed a more direct evaluation to be made of the effects of implanted ions on the microstructure. 11 refs., 14 figs

Subnanosecond pulse measurements of 10.6 μm radiation with tellurium

NARCIS (Netherlands)

Haselhoff, E.H.; Bonnie, R.J.M.; Ernst, G.J.; Witteman, W.J.

1988-01-01

Subnanosecond infrared pulses have been measured by noncollinear secondharmonic generation in tellurium. The method is very practical because due to the high refractive index the fine tuning of the phase matching is easily obtained by rotating the crystal around the optic axis.

Isothermal oxidation behaviour of thermal barrier coatings with CoCrAlY bond coat irradiated by high-current pulsed electron beam

Energy Technology Data Exchange (ETDEWEB)

Cai, Jie [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Guan, Qingfeng, E-mail: guanqf@mail.ujs.edu.cn [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Hou, Xiuli [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Wang, Zhiping; Su, Jingxin; Han, Zhiyong [College of Science, Civil Aviation University of China, Tianjin 300300 (China)

2014-10-30

Highlights: • The original coarse surface was re-melted by pulsed electron beam irradiation. • Very fine grains were homogeneously dispersed on the irradiated coat surface. • A compact Al{sub 2}O{sub 3} scale was formed in irradiated TBCs at the onset of oxidation. • The selective oxidation of Al element avoided the formation of other oxides. • The irradiated coating has a much higher oxidation resistance. - Abstract: Thermal sprayed CoCrAlY bond coat irradiated by high-current pulsed electron beam (HCPEB) and thermal barrier coatings (TBCs) prepared with the irradiated bond coat and the ceramic top coat were investigated. The high temperature oxidation resistance of these specimens was tested at 1050 °C in air. Microstructure observations revealed that the original coarse surface of the as-sprayed bond coat was significantly changed as the interconnected bulged nodules with a compact appearance after HCPEB irradiation. Abundant Y-rich alumina particulates and very fine grains were dispersed on the irradiated surface. After high temperature oxidation test, the thermally grown oxide (TGO) in the initial TBCs grew rapidly and was comprised of two distinct layers: a large percentage of mixed oxides in the outer layer and a relatively small portion of Al{sub 2}O{sub 3} in the inner layer. Severe local internal oxidation and extensive cracks in the TGO layer were discovered as well. Comparatively, the irradiated TBCs exhibited thinner TGO layer, slower TGO growth rate, and homogeneous TGO composition (primarily consisting of Al{sub 2}O{sub 3}). The results indicate that TBCs with the irradiated bond coat have a much higher oxidation resistance.

Formation of tungsten oxide nanowires by ion irradiation and vacuum annealing

Science.gov (United States)

Zheng, Xu-Dong; Ren, Feng; Wu, Heng-Yi; Qin, Wen-Jing; Jiang, Chang-Zhong

2018-04-01

Here we reported the fabrication of tungsten oxide (WO3-x ) nanowires by Ar+ ion irradiation of WO3 thin films followed by annealing in vacuum. The nanowire length increases with increasing irradiation fluence and with decreasing ion energy. We propose that the stress-driven diffusion of the irradiation-induced W interstitial atoms is responsible for the formation of the nanowires. Comparing to the pristine film, the fabricated nanowire film shows a 106-fold enhancement in electrical conductivity, resulting from the high-density irradiation-induced vacancies on the oxygen sublattice. The nanostructure exhibits largely enhanced surface-enhanced Raman scattering effect due to the oxygen vacancy. Thus, ion irradiation provides a powerful approach for fabricating and tailoring the surface nanostructures of semiconductors.

Flotation concentration for tellurium determination in industrial sewage

International Nuclear Information System (INIS)

Skripchuk, V.G.; Bormotova, L.V.; Lukoyanova, L.P.; Tret'yakova, M.I.

1983-01-01

Combination of the flotation of tellurium (4) precipitate with papaverine toluene and extraction-photometric determination of Te with butylrhodamine C allows one to determine 0.002-0.1 mg Te/l without its preliminary precipitation. Accompanying elements found in non-ferrous metallurgy sewage have no effect upon it. The duration of analysis of 10 samples is 1 to 1.5 h. Relative error is 12%. The method is introduced at the ''Uralelektromed'' plant

Flavoprotein-mediated tellurite reduction: structural basis and applications to the synthesis of tellurium-containing nanostructures

Directory of Open Access Journals (Sweden)

Mauricio Arenas-Salinas

2016-07-01

Full Text Available The tellurium oxyanion tellurite (TeO32- is extremely harmful for most organisms. It has been suggested that a potential bacterial tellurite resistance mechanism would consist of an enzymatic, NAD(PH-dependent, reduction to the less toxic form elemental tellurium (Te0. To date, a number of enzymes such as catalase, type II NADH dehydrogenase and terminal oxidases from the electron transport chain, nitrate reductases, and dihydrolipoamide dehydrogenase (E3, among others, have been shown to display tellurite-reducing activity. This activity is generically referred to as tellurite reductase (TR. Bioinformatic data resting on some of the abovementioned enzymes enabled the identification of common structures involved in tellurite reduction including vicinal catalytic cysteine residues and the FAD/NAD(P+-binding domain, which is characteristic of some flavoproteins. Along this line, thioredoxin reductase (TrxB, alkyl hydroperoxide reductase (AhpF, glutathione reductase (GorA, mercuric reductase (MerA, NADH: flavorubredoxin reductase (NorW, dihydrolipoamide dehydrogenase, and the putative oxidoreductase YkgC from Escherichia coli or environmental bacteria were purified and assessed for TR activity. All of them displayed in vitro TR activity at the expense of NADH or NADPH oxidation. In general, optimal reducing conditions occurred around pH 9-10 and 37 °C.Enzymes exhibiting strong TR activity produced Te-containing nanostructures (TeNS. While GorA and AhpF generated TeNS of 75 nm average diameter, E3 and YkgC produced larger structures (> 100 nm. Electron-dense structures were observed in cells over-expressing genes encoding TrxB, GorA and YkgC.

Magnetic resonance force microscopy quantum computer with tellurium donors in silicon.

Science.gov (United States)

Berman, G P; Doolen, G D; Hammel, P C; Tsifrinovich, V I

2001-03-26

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations.

Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

International Nuclear Information System (INIS)

Berman, G. P.; Doolen, G. D.; Hammel, P. C.; Tsifrinovich, V. I.

2001-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

International Nuclear Information System (INIS)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F.

2013-01-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

Energy Technology Data Exchange (ETDEWEB)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F., E-mail: julio.ruivo.costa@usp.br, E-mail: czamboni@ipen.br, E-mail: fisicawagner@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

The dependence of the texture of tellurium thin films on vacuum deposition angle

International Nuclear Information System (INIS)

Cocks, F.H.; Peterson, M.J.; Jones, P.L.

1980-01-01

Vacuum-deposited tellurium thin films can show substantially different surface morphologies depending on the angle with which the vapor stream impinges on the substrate surface. These tellurium thin films have a tendency to grow as acicular crystallites but as the deposition angle is increased so that the vapor stream becomes tangential to the substrate surface the spacing between crystallites increases and approaches, at stream angles of approximately 80 0 from the normal, dimensions roughly once or twice the average wavelength of visible light. Such films may have application in solar energy collector systems because of the high absorptivity of sunlight shown by such films. Mechanisms which describe the tendency for crystallite spacing to increase with increasing angle are discussed. (Auth.)

Ion irradiation-induced diffusion in bixbyite-fluorite related oxides: Dislocations and phase transformation

Energy Technology Data Exchange (ETDEWEB)

Rolly, Gaboriaud, E-mail: Rolly.gaboriaud@univ-poitiers.fr [Institut Pprime, CNRS-University of Poitiers, SP2MI-BP 30179, 86962 Chasseneuil-Futuroscope (France); Fabien, Paumier [Institut Pprime, CNRS-University of Poitiers, SP2MI-BP 30179, 86962 Chasseneuil-Futuroscope (France); Bertrand, Lacroix [CSIC – University of Sevilla, Avenida Américo Vespucio, 49, 41092 Sevilla (Spain)

2014-05-01

Ion-irradiation induced diffusion and the phase transformation of a bixbyite-fluorite related rare earth oxide thin films are studied. This work is focused on yttrium sesquioxide, Y{sub 2}O{sub 3}, thin films deposited on Si (1 0 0) substrates using the ion beam sputtering technique (IBS). As-deposited samples were annealed ant then irradiated at cryogenic temperature (80 K) with 260 keV Xe{sup 2+} at different fluences. The irradiated thin oxide films are characterized by X-ray diffraction. A cubic to monoclinic phase transformation was observed. Analysis of this phenomenon is done in terms of residual stresses. Stress measurements as a function of irradiation fluences were realised using the XRD-sin{sup 2}ψ method. Stress evolution and kinetic of the phase transformation are compared and leads to the role-played by the nucleation of point and extended defects.

Melatonin prevents inflammation and oxidative stress caused by abdominopelvic and total body irradiation of rat small intestine.

Science.gov (United States)

Guney, Y; Hicsonmez, A; Uluoglu, C; Guney, H Z; Ozel Turkcu, U; Take, G; Yucel, B; Caglar, G; Bilgihan, A; Erdogan, D; Nalca Andrieu, M; Kurtman, C; Zengil, H

2007-10-01

We investigated the day-night differences in intestinal oxidative-injury and the inflammatory response following total body (TB) or abdominopelvic (AP) irradiation, and the influence of melatonin administration on tissue injury induced by radiation. Rats (male Wistar, weighing 220-280 g) in the irradiated groups were exposed to a dose of 8 Gy to the TB or AP region in the morning (resting period - 1 h after light onset) or evening (activity span - 13 h after light onset). Vehicle or melatonin was administered immediately before, immediately after and 24 h after irradiation (10, 2.0 and 10 mg/kg, ip, respectively) to the irradiated rats. AP (P < 0.05) and TB (P < 0.05) irradiation applied in the morning caused a significant increase in thiobarbituric acid reactive substance (TBARS) levels. Melatonin treatment in the morning (P < 0.05) or evening (P < 0.05) decreased TBARS levels after TB irradiation. After AP irradiation, melatonin treatment only in the morning caused a significant decrease in TBARS levels (P < 0.05). Although we have confirmed the development of inflammation after radiotherapy by histological findings, neither AP nor TB irradiation caused any marked changes in myeloperoxidase activity in the morning or evening. Our results indicate that oxidative damage is more prominent in rats receiving TB and AP irradiation in the morning and melatonin appears to have beneficial effects on oxidative damage irrespective of the time of administration. Increased neutrophil accumulation indicates that melatonin administration exerts a protective effect on AP irradiation-induced tissue oxidative injury, especially in the morning.

Melatonin prevents inflammation and oxidative stress caused by abdominopelvic and total body irradiation of rat small intestine

Directory of Open Access Journals (Sweden)

Y. Guney

2007-10-01

Full Text Available We investigated the day-night differences in intestinal oxidative-injury and the inflammatory response following total body (TB or abdominopelvic (AP irradiation, and the influence of melatonin administration on tissue injury induced by radiation. Rats (male Wistar, weighing 220-280 g in the irradiated groups were exposed to a dose of 8 Gy to the TB or AP region in the morning (resting period - 1 h after light onset or evening (activity span - 13 h after light onset. Vehicle or melatonin was administered immediately before, immediately after and 24 h after irradiation (10, 2.0 and 10 mg/kg, ip, respectively to the irradiated rats. AP (P < 0.05 and TB (P < 0.05 irradiation applied in the morning caused a significant increase in thiobarbituric acid reactive substance (TBARS levels. Melatonin treatment in the morning (P < 0.05 or evening (P < 0.05 decreased TBARS levels after TB irradiation. After AP irradiation, melatonin treatment only in the morning caused a significant decrease in TBARS levels (P < 0.05. Although we have confirmed the development of inflammation after radiotherapy by histological findings, neither AP nor TB irradiation caused any marked changes in myeloperoxidase activity in the morning or evening. Our results indicate that oxidative damage is more prominent in rats receiving TB and AP irradiation in the morning and melatonin appears to have beneficial effects on oxidative damage irrespective of the time of administration. Increased neutrophil accumulation indicates that melatonin administration exerts a protective effect on AP irradiation-induced tissue oxidative injury, especially in the morning.

Irradiation Effect on Oxidative Condition and Tocopherol Content of Vegetable Oils

Directory of Open Access Journals (Sweden)

Konstantinos Sflomos

2007-06-01

Full Text Available The effect on induction period and tocopherol content after γ-irradiation onsamples of olive oil and seed oils (sunflower and soybean was determined. In seed oilsamples 0, 100, 200 and 300 ppm of δ-tocopherol were added before irradiation with 1, 2and 3kGy. The results of induction period showed that, after irradiation, all samplespresented a significant decreased in resistance to oxidation. However, this decrease wasminimized when δ-tocopherol was added. Irradiation significantly decreased the level oftocopherols. δ-Tocopherol appeared more sensitive in irradiation process than α- andγ-tocopherol. The addition of δ-tocopherol significantly reduced, in most cases, thedepletion of the other tocopherols.

Contribution to the development of the MARS beamline to study oxide dispersion strengthened steels (ODS) irradiated with neutrons using synchrotron source: secondary phases evolution under irradiation

International Nuclear Information System (INIS)

Menut, Denis

2016-01-01

X-Ray Diffraction (XRD) coupled with X-ray Absorption Fine Structure (XAFS) analyses at the MARS beamline of the synchrotron SOLEIL facility were used to study the microstructural evolution of oxides phases found in oxide dispersion strengthened steels (ODS) irradiated in Material Testing Reactors. Two hold generations of ODS steel grades (DY and MA957) irradiated up to high fluencies (∼75 dpa) were studied. These experiments have required specific developments, in particular a dedicated sample holder. An important milestone was overcome integrating the MARS beamline to the nuclearized facilities accessible for CEA. First, XRD analysis provide new results concerning intermediate sizes of precipitates (around 100 nm) essentially from crystallographic point of view, the nano-sized oxides (from 1 to 10 nm) being not detected, due to the material itself, sample preparation as thin foil and experimental set-up calibration. Secondly, XAFS analysis is not a discriminating technique as soon as the absorber atom is involved in the chemical composition of various precipitates found in ODS. Nevertheless, the stability of the Ti with a coordination number of 5 is evidenced whatever the irradiation conditions. As our experimental study was not able to detect the nano-sized oxides, an alternative way is to perform modeling approach of the behavior of massive oxides under irradiation, compared to experimental analyses under ion irradiations. We have shown that the defect fluorite is an intermediate phase of the crystal-to-amorphous phase transition of the pyrochlore oxide structure, whatever the irradiation conditions and the ratio of the cationic radii, the Ti coordination number remaining around 5 in the amorphous state. (author) [fr

Large-scale synthesis of Tellurium nanostructures via galvanic displacement of metals

Science.gov (United States)

Kok, Kuan-Ying; Choo, Thye-Foo; Ubaidah Saidin, Nur; Rahman, Che Zuraini Che Ab

2018-01-01

Tellurium (Te) is an attractive semiconductor material for a wide range of applications in various functional devices including, radiation dosimeters, optical storage materials, thermoelectric or piezoelectric generators. In this work, large scale synthesis of tellurium (Te) nanostructures have been successfully carried out in different concentrations of aqueous solutions containing TeO2 and NaOH, by galvanic displacements of Zn and Al which served as the sacrificial materials. Galvanic displacement process is cost-effective and it requires no template or surfactant for the synthesis of nanostructures. By varying the concentrations of TeO2 and NaOH, etching temperatures and etching times, Te nanostructures of various forms of nanostructures were successfully obtained, ranging from one-dimensional needles and rod-like structures to more complex hierarchical structures. Microscopy examinations on the nanostructures obtained have shown that both the diameters and lengths of the Te nanostructures increased with increasing etching temperature and etching time.

Irradiation creep of the mixed oxide UPuO2

International Nuclear Information System (INIS)

Combette, Patrick; Milet, Claude

1976-01-01

The irradiation creep under compression of the mixed oxide UO 2 -PuO 2 was studied up to fission yields of 6x10 13 fcm -3 s -1 , under stresses -2 , in the temperature range 700-900 deg C. The creep rate is proportional to the applied stress and fission yield, athermal in the studied temperature range and non-dependent of burnup (up to 30000MWjt -1 ). In a sample under compression, swelling is observed due to the formation of fission products during the irradiation and the swelling rate is of the same order that in a cladded fuel element [fr

Inhibition of DNA repair by whole body irradiation induced nitric oxide leads to higher radiation sensitivity in lymphocytes

International Nuclear Information System (INIS)

Sharma, Deepak; Santosh Kumar, S.; Raghu, Rashmi; Maurya, D.K.; Sainis, K.B.

2007-01-01

Full text: It is well accepted that the sensitivity of mammalian cells is better following whole body irradiation (WBI) as compared to that following in vitro irradiation. However, the underlying mechanisms are not well understood. Following WBI, the lipid peroxidation and cell death were significantly higher in lymphocytes as compared to that in vitro irradiated lymphocytes. Further, WBI treatment of tumor bearing mice resulted in a significantly higher inhibition of EL-4 cell proliferation as compared to in vitro irradiation of EL-4 cells. The DNA repair was significantly slower in lymphocytes obtained from WBI treated mice as compared to that in the cells exposed to same dose of radiation in vitro. Generation of nitric oxide following irradiation and also its role in inhibition of DNA repair have been reported, hence, its levels were estimated under both WBI and in vitro irradiation conditions. Nitric oxide levels were significantly elevated in the plasma of WBI treated mice but not in the supernatant of in vitro irradiated cells. Addition of sodium nitroprusside (SNP), a nitric oxide donor to in vitro irradiated cells inhibited the repair of DNA damage and sensitized cells to undergo cell death. It also enhanced the radiation-induced functional impairment of lymphocytes as evinced from suppression of mitogen-induced IL-2, IFN-γ and bcl-2 mRNA expression. Administration of N G -nitro-L-arginine-methyl-ester(L-NAME), a nitric oxide synthase inhibitor, to mice significantly protected lymphocytes against WBI-induced DNA damage and inhibited in vivo radiation-induced production of nitric oxide. Our results indicated that nitric oxide plays a role in the higher radiosensitivity of lymphocytes in vivo by inhibiting repair of DNA damage

Iodine-129 in thyroids and tellurium isotopes in meteorites by neutron activation analysis

International Nuclear Information System (INIS)

Ballad, R.V.

1978-06-01

A combination of neutron activation and mass spectrometry has been used to determine the concentration of fissiogenic 129 I and the value of the 129 I/ 127 I ratio in thyroids of man, cow, and deer from Missouri. Deer thyroids show an average value of 129 I/ 127 I = 1.8 x 10 -8 and an average concentration of 3 x 10 -3 pCi 129 I per gram of thyroid (wet weight). Thyroids of cows and humans show successively lower values for the 129 I/ 127 I ratio and the 129 I content because their diets dilute fission-produced 129 I in the natural iodine cycle with mineral iodine. The results of analyses on a few thyroids from other geographic areas are also reported. The isotopic compositions of tellurium, krypton, and xenon were determined in acid-resistant residues of the Allende meteorite. Neutron activation and γ-counting were used to determine the relative abundances of six tellurium isotopes, and mass spectrometry was used to determine the isotopic compositions of krypton and xenon in aliquots of the same residues. Nucleogenetic anomalies were observed in the isotopic compositions of these three elements. The presence of isotopically distinct components of tellurium, krypton, and xenon in these residues provides strong support for the suggestion that our solar system formed directly from the debris of a supernova

Effect of different antioxidants on lipid oxidation of irradiated cooked streaky pork

International Nuclear Information System (INIS)

Guo Shuzhen; Ha Yiming; Zhang Haiwei; Wang Feng; Liu Shuliang

2008-01-01

The effects of antioxidants on lipid oxidation of vacuum packaged irradiated cooked streaky pork were studied. The cooked streaky pork were added with 0.02% TeaPolyphenols (TP), rosemary, Tertiary butylhydroquinone (TBHQ), Butylated hydroxytoluene (BHT) and vitamin E separately, then were irradiated with 6 kGy, and stored at 4 degree C. The results showed that antioxidants can reduce the value of TBA, POV value of irradiated cooked streaky pork, and the effects of TBHQ and TP were better, than other antiatidins. (authors)

Vitamin C affects the antioxidative/oxidative status in rats irradiated with ultraviolet (UV) and infrared (IR) light

DEFF Research Database (Denmark)

Niemiec, T.; Sawosz, E.; Chwalibog, André

2006-01-01

Four grups of twenty growing Wistar rats were irradiated with either UV, IR, UV+IR light or were not irradiated (control). Ten rats from each group received a diet supplemented with 0.6% of L-ascorbic acid. The effects of the mega-dose of vitamin C were evaluated by changes in the antioxidative....../oxidative status. UV and IR radiation promoted oxidative DNA degradation in rat livers and supplementation with ascorbic acid strengthened the prooxidative effects on DNA oxidation in rats irradiated with UV or IR light. Vitamin C also increased the tiobarbituric acid reactive substances (TBARS) concentration...

Effects of ascorbic acid and antioxidants on color, lipid oxidation and volatiles of irradiated ground beef

International Nuclear Information System (INIS)

Ahn, D.U.; Nam, K.C.

2004-01-01

Beef loins with 3 different aging times after slaughter were ground, added with none, 0.1% ascorbic acid, 0.01% sesamol+0.01% α-tocopherol, or 0.1% ascorbic acid+0.01% sesamol+0.01% tocopherol. The meats were packaged in oxygen-permeable bags, irradiated at 2.5 kGy, and color, oxidation-reduction potential (ORP), lipid oxidation and volatile profiles were determined. Irradiation decreased the redness of ground beef, and visible color of beef changed from a bright red to a green/brown depending on the age of meat. Addition of ascorbic acid prevented color changes in irradiated beef, and the effect of ascorbic acid became greater as the age of meat or storage time after irradiation increased. The ground beef added with ascorbic acid had lower ORP than control, and the low ORP of meat helped maintaining the heme pigments in reduced form. During aerobic storage, S-volatiles disappeared while volatile aldehydes significantly increased in irradiated beef. Addition of ascorbic acid at 0.1% or sesamol+α-tocopherol at each 0.01% level to ground beef prior to irradiation were effective in reducing lipid oxidation and S-volatiles. As storage time increased, however, the antioxidant effect of sesamol+tocopherol in irradiated ground beef was superior to that of ascorbic acid

Effects of ascorbic acid and antioxidants on color, lipid oxidation and volatiles of irradiated ground beef

Energy Technology Data Exchange (ETDEWEB)

Ahn, D.U. E-mail: duahn@iastate.edu; Nam, K.C

2004-10-01

Beef loins with 3 different aging times after slaughter were ground, added with none, 0.1% ascorbic acid, 0.01% sesamol+0.01% {alpha}-tocopherol, or 0.1% ascorbic acid+0.01% sesamol+0.01% tocopherol. The meats were packaged in oxygen-permeable bags, irradiated at 2.5 kGy, and color, oxidation-reduction potential (ORP), lipid oxidation and volatile profiles were determined. Irradiation decreased the redness of ground beef, and visible color of beef changed from a bright red to a green/brown depending on the age of meat. Addition of ascorbic acid prevented color changes in irradiated beef, and the effect of ascorbic acid became greater as the age of meat or storage time after irradiation increased. The ground beef added with ascorbic acid had lower ORP than control, and the low ORP of meat helped maintaining the heme pigments in reduced form. During aerobic storage, S-volatiles disappeared while volatile aldehydes significantly increased in irradiated beef. Addition of ascorbic acid at 0.1% or sesamol+{alpha}-tocopherol at each 0.01% level to ground beef prior to irradiation were effective in reducing lipid oxidation and S-volatiles. As storage time increased, however, the antioxidant effect of sesamol+tocopherol in irradiated ground beef was superior to that of ascorbic acid.

Modification of graphite structure by irradiation, revealed by thermal oxidation. Examination by electronic microscopy

International Nuclear Information System (INIS)

Rouaud, Michel

1969-01-01

Based on the analysis of images obtained by electronic microscopy, this document reports the comparative study of the action of neutrons on three different graphites: a natural one (Ticonderoga) and two pyrolytic ones (Carbone-Lorraine and Raytheon). The approach is based on the modification of features of thermal oxidation of graphites by dry air after irradiation. Different corrosion features are identified. The author states that there seems to be a relationship between the number and shape of these features, and defects existing on the irradiated graphite before oxidation. For low doses, the feature aspect varies with depth at which oxidation occurs. For higher doses, the aspect remains the same [fr

Irradiation of mixed UO2-PuO2 oxide samples for fast neutron reactor fuel elements

International Nuclear Information System (INIS)

Mikailoff, H.; Mustelier, J.; Bloch, J.; Conte, M.; Hayet, L.; Lauthier, J.C.; Leclere, J.

1968-01-01

Thermal flux irradiation testings of small mixed oxide pellets UPuO 2 fuel elements were performed in support of the fuel reference design for the Phenix fast reactor. The effects of different parameters (stoichiometry, pellet density, pellet clad gap). on the behaviour of the oxide (temperature distribution, microstructural changes, fission gas release) were investigated in various irradiation conditions. In particular, the effect of fuel density decrease and power rate increase on thermal performances were determined on short term irradiations of porous fuels. (authors) [fr

Effects of soy sauce and packaging method on volatile compounds and lipid oxidation of cooked irradiated beef patties

International Nuclear Information System (INIS)

Kim, Hyun-Wook; Lee, Soo-Yeon; Hwang, Ko-Eun; Song, Dong-Heon; Kim, Yong-Jae; Ham, Yun-Kyung; Lee, Choong-Hee; Choi, Yun-Sang; Lee, Ju-Woon; Kim, Cheon-Jei

2014-01-01

The objective of this study is to determine the effect of soy sauce on volatile compounds and lipid oxidation of cooked irradiated beef patties. Sulfur-containing volatile components, which are produced by irradiation, were not found in all treatments. Volatile components derived from soy sauce, such as 3-hydroxy-2-butanone, acetic acid, 3-methyl-1-butanol and 2-methyl-1-butanol, were detected in beef patties containing soy sauce regardless of irradiation and packaging method. Volatile aldehydes, including hexanal, significantly decreased the irradiated beef patty prepared with soy sauce compared to those of irradiated beef patty made with NaCl at 1 day and 5 days after irradiation. In addition, combined use of vacuum packaging and soy sauce treatments could inhibit the formation of volatile compounds and 2-thiobarbituric acid reactive substances during chilled storage. Therefore, the use of soy sauce in cooked and irradiated beef could reduce the production of volatile components associated with the irradiation-induced off-flavor and lipid oxidation. - Highlights: • Soy sauce (SS) could inhibit volatiles cooked irradiated beef patties. • Vacuum packaging and SS treatment is effective to prevent lipid oxidation. • Hexanal content was highly correlated with TBA value of the irradiated beef patties

Chemical interaction between (Cs-Te) doped fuels and cladding material under irradiation

International Nuclear Information System (INIS)

Delbrassine, A.; Flipot, A.J.

1977-01-01

Pins containing UO 2 -30 wt.% PuO 2 low density pellets and or caesium and or tellurium as doping elements have been irradiated for about 40 days in the BR 2 reactor. The effect of two Cs/Te ratios, namely 1.3 and 4, and a wide range of O/M ratios on the inner corrosion of the clad has been investigated. The influence of tellurium on the attack of the cladding has been pointed out. It may be responsible for the chromium and nickel depletion in the grain boundaries of the steal. The corrosion patterns and the thickness of the corroded layer could be different in the total length of a fuel pin. It seems therefore necessary to measure the effective Cs/Te ratio associated with the local corrosion layers. This local Cs/Te ratio should be more useful than the initial mean Cs/Te ratio in a pin for understanding the corrosion phenomena. (author)

Protein aggregation in food models: effect of γ-irradiation and lipid oxidation

International Nuclear Information System (INIS)

Delincee, H.; Paul, P.

1981-01-01

Myoglobin and serum albumin have been irradiated in aqueous solution in the presence of varying amounts of carbohydrates and lipids, and the yield of protein aggregates has been determined by gel filtration. With myoglobin the formation of aggregates evolving from the reaction with oxidizing lipids was observed, which was not found for serum albumin. The production of protein-lipid complexes, in which lipid material was occluded in the high-molecular aggregates by physical forces was demonstrated. Gel filtration and gel electrophoresis, both in the presence of SDS, and thin-layer isoelectric focusing revealed distinct structural differenes between the protein aggregates induced by irradiation and the aggregates formed by interaction with oxidizing lipids

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow

The role of nitric oxide radicals in removal of hyper-radiosensitivity by priming irradiation

International Nuclear Information System (INIS)

Edin, Nina Jeppesen; Sandvik, Joe Alexander; Pettersen, Erik Olai; Vollan, Hilde Synnove; Reger, Katharina; Görlach, Agnes

2013-01-01

In this study, a mechanism in which low-dose hyper-radiosensitivity (HRS) is permanently removed, induced by low-dose-rate (LDR) (0.2 - 0.3 Gy/h for 1 h) but not by high-dose-rate priming (0.3 Gy at 40 Gy/h) was investigated. One HRS-negative cell line (NHIK 3025) and two HRS-positive cell lines (T-47D, T98G) were used. The effects of different pretreatments on HRS were investigated using the colony assay. Cell-based ELISA was used to measure nitric oxide synthase (NOS) levels, and microarray analysis to compare gene expression in primed and unprimed cells. The data show how permanent removal of HRS, previously found to be induced by LDR priming irradiation, can also be induced by addition of nitric oxide (NO)-donor DEANO combined with either high-dose-rate priming or exposure to prolonged cycling hypoxia followed by reoxygenation, a treatment not involving radiation. The removal of HRS appears not to involve DNA damage induced during priming irradiation as it was also induced by LDR irradiation of cell-conditioned medium without cells present. The permanent removal of HRS in LDR-primed cells was reversed by treatment with inducible nitric oxide synthase (iNOS) inhibitor 1400W. Furthermore, 1400W could also induce HRS in an HRS-negative cell line. The data suggest that LDR irradiation for 1 h, but not 15 min, activates iNOS, and also that sustained iNOS activation is necessary for the permanent removal of HRS by LDR priming. The data indicate that nitric oxide production is involved in the regulatory processes determining cellular responses to low-dose-rate irradiation. (author)

Thermoelectric properties of bismuth antimony tellurium thin films through bilayer annealing prepared by ion beam sputtering deposition

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhuang-hao [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Fan, Ping, E-mail: fanping308@126.com [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Luo, Jing-ting [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Cai, Xing-min; Liang, Guang-xing; Zhang, Dong-ping [College of Physics Science and Technology, Shenzhen University, 518060 (China); Ye, Fan [Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China)

2014-07-01

Bismuth antimony tellurium is one of the most important tellurium-based materials for high-efficient thermoelectric application. In this paper, ion beam sputtering was used to deposit Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films on borosilicate substrates at room-temperature. Then the bismuth antimony tellurium thin films were synthesized via post thermal treatment of the Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films. The effect of annealing temperature and compositions on the thermoelectric properties of the thin films was investigated. After the thin films were annealed from 150 °C to 350 °C for 1 h in the high vacuum condition, the Seebeck coefficient changed from a negative sign to a positive sign. The X-ray diffraction results showed that the synthesized tellurium-based thermoelectric thin film exhibited various alloys phases, which contributed different thermoelectricity conductivity to the synthesized thin film. The overall Seebeck coefficient of the synthesized thin film changed from negative sign to positive sign, which was due to the change of the primary phase of the tellurium-based materials at different annealing conditions. Similarly, the thermoelectric properties of the films were also associated with the grown phase. High-quality thin film with the Seebeck coefficient of 240 μV K{sup −1} and the power factor of 2.67 × 10{sup −3} Wm{sup −1} K{sup −2} showed a single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase when the Sb/Te thin film sputtering time was 40 min. - Highlights: • Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} thermoelectric thin films synthesized via bilayer annealing • The film has single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase with best thermoelectric performance. • The film has high thermoelectric properties comparable with other best results.

Growth of porous type anodic oxide films at micro-areas on aluminum exposed by laser irradiation

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, Tatsuya [Graduate School of Engineering, Hokkaido University, N13-W8, Kita-Ku, Sapporo 060-8628 (Japan)], E-mail: kiku@eng.hokudai.ac.jp; Sakairi, Masatoshi [Graduate School of Engineering, Hokkaido University, N13-W8, Kita-Ku, Sapporo 060-8628 (Japan); Takahashi, Hideaki [Asahikawa National College of Technology, Syunkohdai, 2-2, 1-6, Asahikawa 071-8142 (Japan)

2009-11-30

Aluminum covered with pore-sealed anodic oxide films was irradiated with a pulsed Nd-YAG laser to remove the oxide film at micro-areas. The specimen was re-anodized for long periods to examine the growth of porous anodic oxide films at the area where substrate had been exposed by measuring current variations and morphological changes in the oxide during the re-anodizing. The chemical dissolution resistance of the pore-sealed anodic oxide films in an oxalic acid solution was also examined by measuring time-variations in rest potentials during immersion. The resistance to chemical dissolution of the oxide film became higher with increasing pore-sealing time and showed higher values at lower solution temperatures. During potentiostatic re-anodizing at five 35-{mu}m wide and 4-mm long lines for 72 h after the film was removed the measured current was found to increase linearly with time. Semicircular columnar-shaped porous type anodic oxide was found to form during the re-anodizing at the laser-irradiated area, and was found to grow radially, thus resulting in an increase in the diameter. After long re-anodizing, the central and top parts of the oxide protruded along the longitudinal direction of the laser-irradiated area. The volume expansion during re-anodizing resulted in the formation of cracks, parallel to the lines, in the oxide film formed during the first anodizing.

Pathfinder irradiation of advanced fuel (Th/U mixed oxide) in a power reactor

International Nuclear Information System (INIS)

Brant Pinheiro, R.

1993-01-01

Within the joint Brazilian-German cooperative R and D Program on Thorium Utilization in Pressurized Water Reactors carried out from 1979 to 1988 by Nuclebras/CDTN, KFA-Juelich, Siemens/KWU and NUKEM, a pathfinder irradiation of Th/U mixed oxide fuel in the Angra 1 nuclear power reactor was planned. The objectives of this irradiation testing, the irradiation strategy, the work performed and the status achieved at the end of the joint Program are presented. (author)

Effect of heavy ion irradiation and α+β phase heat treatment on oxide of Zr-2.5Nb pressure tube material

Energy Technology Data Exchange (ETDEWEB)

Choudhuri, Gargi, E-mail: gargi@barc.gov.in [Quality Assurance Division, BARC, Mumbai, 400085 (India); Mukherjee, P.; Gayathri, N. [Variable Energy Cyclotron Centre, Kolkata, 700064 (India); Kain, V.; Kiran Kumar, M.; Srivastava, D. [Material Science Division, BARC, Mumbai, 400085 (India); Basu, S. [Solid State Physics Division, BARC, Mumbai, 400085 (India); Mukherjee, D. [Quality Assurance Division, BARC, Mumbai, 400085 (India); Dey, G.K. [Material Science Division, BARC, Mumbai, 400085 (India)

2017-06-15

Effect of heavy-ion irradiation on the crystalline phase transformation of oxide of Zr-2.5Nb alloys has been studied. The steam-autoclaved oxide of pressure tube is irradiated with 306 KeV Ar{sup +9} ions at a dose of 3 × 10{sup 19} Ar{sup +9}/m{sup 2}. The damage profile has been estimated using “Stopping and Range of Ions in Matter” computer program. The variation of the crystal structure along the depth of the irradiated oxide have been characterized non-destructively by Grazing Incidence X-ray Diffraction technique and compared with unirradiated-oxide. The effect of different base metal microstructures on the characteristic of oxide has also been studied. Base metal microstructure as well as the cross-sectional oxide have been characterized using transmission electron microscope. Heavy ion irradiation can significantly alter the distribution of phases in the oxide of the alloy. The difference in chemical state of alloying element has also been found between unirradiated-oxide with that of irradiated-oxide using X-ray photo electron spectroscopy. Chemical state of Nb in steam autoclaved oxide is also altered when the base metal is α + β heat treated.

Equilibrium state of delta-phase with tellurium in the Sb-Bi-Te system

International Nuclear Information System (INIS)

Gajgukova, V.S.; Dudkin, L.D.; Erofeev, R.S.; Musaelyan, V.V.; Nadzhip, A.Eh.; Sokolov, O.B.

1978-01-01

A research has been carried out with a view to establish the equilibrium state of delta-phase of the composition (Sbsub(1-x)Bisub(x)) 2 Te 3 with tellurium, depending on x and temperature. The Hall effect, the thermoelectromotive force, and the electric conductivity of the samples of Sb-Bi-Te alloys have been measured, the samples being annealed at various temperatures (550 to 250 deg C). The measurement results have shown that as the Bi 2 Te 3 content in the solid solutions increases and temperature decreases, the delta-phase-Te boundary monotonously approaches the stoichiometric composition. Using the research carrid out as the basis, the general character of the equilibrium delta-phase with tellurium boundary has been rendered more precise in Sb-Bi-Te system, depending on the temperature and Bi content (up to 25 at.%)

Modulator Effect of Turmeric on Oxidative Damage in Whole Body Gamma Irradiated rats

International Nuclear Information System (INIS)

Amin, H.H.; Abdou, M.I.

2012-01-01

Because of its penetrating power and its ability to travel great distances, gamma rays are considered the primary hazard to the population during most radiological emergencies. So, there is a need to develop medical countermeasures to protect the first responders and remediation workers from biomedical effect of ionizing radiation. Turmeric has been reported to have many beneficial health effects, including a strong anti-oxidant effect, anti-inflammatory and anti-microbial properties. In the present study, turmeric was investigated as a therapeutic agent against hazards induced by ionizing radiation on kidney, liver, urinary and serum calcium levels and blood counts. A daily dose of 0.5 g/kg body weight was used in whole body gamma irradiated female rats with 3 Gy. Radiation effects were followed up for four weeks post irradiation. The results revealed that the administration of turmeric post-irradiation resulted in a significant inhibition in the frequency of radiation induced oxidative damage. It could be concluded that definite turmeric dose exerts a vital modulator role against gamma irradiation hazard

GALVANIC MAGNETIC PROPERTIES OF BISMUTH THIN FILMS DOPED WITH TELLURIUM MADE BY THERMAL VACUUM EVAPORATION

Directory of Open Access Journals (Sweden)

V. A. Komarov

2013-01-01

Full Text Available The influence of n-type impurity of tellurium (concentration range from 0.005 atomic % Te to 0.15 atomic % Te on galvanic magnetic properties (resistivity, magnetic resistance and Hall constant of Bi thin films with various thicknesses was studied. The properties were measured in temperature range from 77 to 300 K. It was established that the classical size effect in the films is significant and decreases with higher concentration of Te impurity. The analysis of experimental results was carried out in approximation of the law of Jones-Schoenberg dispersion for Bi films doped with tellurium. Calculation of concentration and mobility of charge carriers in the studied films was made.

Hydrogen-assisted post-growth substitution of tellurium into molybdenum disulfide monolayers with tunable compositions

Science.gov (United States)

Yin, Guoli; Zhu, Dancheng; Lv, Danhui; Hashemi, Arsalan; Fei, Zhen; Lin, Fang; Krasheninnikov, Arkady V.; Zhang, Ze; Komsa, Hannu-Pekka; Jin, Chuanhong

2018-04-01

Herein we report the successful doping of tellurium (Te) into molybdenum disulfide (MoS2) monolayers to form MoS2x Te2(1-x) alloy with variable compositions via a hydrogen-assisted post-growth chemical vapor deposition process. It is confirmed that H2 plays an indispensable role in the Te substitution into as-grown MoS2 monolayers. Atomic-resolution transmission electron microscopy allows us to determine the lattice sites and the concentration of introduced Te atoms. At a relatively low concentration, tellurium is only substituted in the sulfur sublattice to form monolayer MoS2(1-x)Te2x alloy, while with increasing Te concentration (up to ˜27.6% achieved in this study), local regions with enriched tellurium, large structural distortions, and obvious sulfur deficiency are observed. Statistical analysis of the Te distribution indicates the random substitution. Density functional theory calculations are used to investigate the stability of the alloy structures and their electronic properties. Comparison with experimental results indicate that the samples are unstrained and the Te atoms are predominantly substituted in the top S sublattice. Importantly, such ultimately thin Janus structure of MoS2(1-x)Te2x exhibits properties that are distinct from their constituents. We believe our results will inspire further exploration of the versatile properties of asymmetric 2D TMD alloys.

Magnetic, thermal and luminescence properties in room-temperature nanosecond electron-irradiated various metal oxide nanopowders

Science.gov (United States)

Sokovnin, S. Yu; Balezin, M. E.; Il’ves, V. G.

2018-03-01

By means of pulsed electron beam evaporation in vacuum of targets non-magnetic, in bulk state, Al2O3 and YSZ (ZrO2-8% Y2O3) oxides, magnetic nanopowders (NPs) with a high specific surface were produced. The NPs were subsequently irradiated in air by electrons with energy of 700 keV, using a URT-1 accelerator for 15 and 30 minutes. The magnetic, thermal, and pulsed cathodoluminescence (PCL) characteristics of NPs were measured before and after irradiation. It was established that the electron irradiation non-monotonically changes the magnetization of the pristine samples. To the contrary, a clear correlation between the intensity of PCL and the irradiation doses is found in the oxides. There was a decrease in the intensity of PCL after irradiation. Luminescent and thermal properties reflect the transformation of structural defects in NPs more strongly after the exposure to a pulsed electron beam in comparison with corresponding changes of the NPs magnetic response.

Protein Oxidation in the Lungs of C57BL/6J Mice Following X-Irradiation

Science.gov (United States)

Barshishat-Kupper, Michal; McCart, Elizabeth A.; Freedy, James G.; Tipton, Ashlee J.; Nagy, Vitaly; Kim, Sung-Yop; Landauer, Michael R.; Mueller, Gregory P.; Day, Regina M.

2015-01-01

Damage to normal lung tissue is a limiting factor when ionizing radiation is used in clinical applications. In addition, radiation pneumonitis and fibrosis are a major cause of mortality following accidental radiation exposure in humans. Although clinical symptoms may not develop for months after radiation exposure, immediate events induced by radiation are believed to generate molecular and cellular cascades that proceed during a clinical latent period. Oxidative damage to DNA is considered a primary cause of radiation injury to cells. DNA can be repaired by highly efficient mechanisms while repair of oxidized proteins is limited. Oxidized proteins are often destined for degradation. We examined protein oxidation following 17 Gy (0.6 Gy/min) thoracic X-irradiation in C57BL/6J mice. Seventeen Gy thoracic irradiation resulted in 100% mortality of mice within 127–189 days postirradiation. Necropsy findings indicated that pneumonitis and pulmonary fibrosis were the leading cause of mortality. We investigated the oxidation of lung proteins at 24 h postirradiation following 17 Gy thoracic irradiation using 2-D gel electrophoresis and OxyBlot for the detection of protein carbonylation. Seven carbonylated proteins were identified using mass spectrometry: serum albumin, selenium binding protein-1, alpha antitrypsin, cytoplasmic actin-1, carbonic anhydrase-2, peroxiredoxin-6, and apolipoprotein A1. The carbonylation status of carbonic anhydrase-2, selenium binding protein, and peroxiredoxin-6 was higher in control lung tissue. Apolipoprotein A1 and serum albumin carbonylation were increased following X-irradiation, as confirmed by OxyBlot immunoprecipitation and Western blotting. Our findings indicate that the profile of specific protein oxidation in the lung is altered following radiation exposure. PMID:28248270

Activity and selectivity of manganese oxides in alcohols Conversion as influenced by gamma-irradiation

International Nuclear Information System (INIS)

Doheim, M.M.; Ahmed, A.S.; El-Shobaky, G.A.

2002-01-01

Manganese oxide samples obtained from thermal decomposition of manganese carbonate at 400 and 600 deg C were subjected to different doses of g-irradiation within the range 0.2 to 1.6 MGy. The surface and catalytic properties of the above samples were studied using nitrogen adsorption isotherms measured at -196 deg C and catalytic conversion of ethanol and isopropanol at 300-400 deg C using micropulse technique. The results obtained revealed that manganese oxides obtained at 400 deg C consisted of a mixture of Mn 2 O 3 and MnO 2 while the samples calcined at 600 deg C composed entirely of Mn 2 O 3 . Gamma-irradiation resulted in a decrease in the particle size of manganese oxide phases with subsequent increase in their specific surface areas. Gamma-irradiation with 0.2 and 0.8 MGy effected a measurable progressive decrease in the catalytic activity in dehydration and dehydrogenation of both alcohols. However, the treated catalyst retained their initial activity upon exposure to a dose of 1.6 MGy. Also, g-irradiation increased the selectivities of the investigated solids towards dehydrogenation of both alcohols. The catalyst samples precalcined at 600 deg C exhibited higher catalytic activities than those precalcined at 400 deg C. (author)

Separation of Protactinium from Neutron Irradiated Thorium Oxide

International Nuclear Information System (INIS)

Dominguez, G.; Gutierrez, L.; Ropero, M.

1983-01-01

The chemical separation of thorium and protactinium can be carried out by leaching most of the last one, about 95%, with aqueous HF from neutron irradiated thorium oxide. This leaching reaction la highly favored by the transformation reaction of the ThO 2 material into ThF 4 . For both reactions, leaching and transformation, the reagents concentration, agitation speed and temperature influences were studied and the activation energies were found. (Author) 18 refs

Electric field fluctuations in liquid tellurium alloys a hint to bond character

NARCIS (Netherlands)

Paulick, C.A.; Brinkmann, R.; Elwenspoek, Michael Curt; von Hartrott, M.; Kiehl, M.; Maxim, P.; Quitmann, D.

1985-01-01

Atomic scale electric field fluctuations in liquid tellurium alloys are detected as they induce nuclear spin relaxation rate RQ in noble gas impurity atoms, via quadrupolar interaction. Results for Xe in liquid Ag, Ga, In, Tl, Ge, Sn---Te alloys are discussed, assuming that bonding in these alloys

Point defects and irradiation in oxides: simulations at the atomic scale

International Nuclear Information System (INIS)

Crocombette, J.P.

2005-11-01

The author gives an overview of his research activity since 1995. This activity concerns research in materials science, and more particularly the ageing of oxides present in the nuclear industry, or more generally, the evolution of these materials under irradiation. The first part deals with the investigation of point defects, and more particularly of the structures and energies of these defects. The author discusses results obtained on uranium dioxide, on amorphous silica, and on the solution of oxygen in silver. The second part deals with irradiation-induced damages in crystalline matrices storing radioactive actinides, and more particularly with the effect of alpha disintegration decay nuclei which are the main sources of long term irradiation in these materials

Lipid oxidation and volatile production in irradiated raw pork batters prepared with commercial soybean oil containing vitamin E

Energy Technology Data Exchange (ETDEWEB)

Jo, Cheorun; Ahn, D.U.; Byun, M.W. E-mail: mwbyun@kaeri.re.kr

2001-04-01

An emulsion-type raw pork batter was prepared using 10% (meat weight) of backfat or commercial soybean oil enriched with vitamin E to determine the effect of irradiation on lipid oxidation and volatile production during storage. Batters (approximately 100 g) were vacuum- or aerobically packaged and irradiated at 0, 2.5 or 4.5 kGy. Irradiation increased lipid oxidation of aerobically packaged raw pork batters prepared with both backfat and soybean oil. Lipid oxidation of vacuum-packaged pork batters was not influenced by irradiation except for the batter prepared with backfat at day 0. Aerobically packaged batters prepared with soybean oil had lower (P<0.05) TBARS than that with backfat, but vacuum-packaged ones were not different. The sum of volatile compounds with short retention time (<1.80) increased by irradiation, and with storage time except for aerobic packaging at day 7. The amount of total volatile compounds had an increasing trend until day 3, but not at day 7. Irradiation increased the production of total volatile compounds in the batters prepared with soybean oil and vacuum packaged, but irradiation effect on volatile production was not consistent with other treatments.

Lipid oxidation and volatile production in irradiated raw pork batters prepared with commercial soybean oil containing vitamin E

International Nuclear Information System (INIS)

Jo, Cheorun; Ahn, D.U.; Byun, M.W.

2001-01-01

An emulsion-type raw pork batter was prepared using 10% (meat weight) of backfat or commercial soybean oil enriched with vitamin E to determine the effect of irradiation on lipid oxidation and volatile production during storage. Batters (approximately 100 g) were vacuum- or aerobically packaged and irradiated at 0, 2.5 or 4.5 kGy. Irradiation increased lipid oxidation of aerobically packaged raw pork batters prepared with both backfat and soybean oil. Lipid oxidation of vacuum-packaged pork batters was not influenced by irradiation except for the batter prepared with backfat at day 0. Aerobically packaged batters prepared with soybean oil had lower (P<0.05) TBARS than that with backfat, but vacuum-packaged ones were not different. The sum of volatile compounds with short retention time (<1.80) increased by irradiation, and with storage time except for aerobic packaging at day 7. The amount of total volatile compounds had an increasing trend until day 3, but not at day 7. Irradiation increased the production of total volatile compounds in the batters prepared with soybean oil and vacuum packaged, but irradiation effect on volatile production was not consistent with other treatments

Dietary vitamin E affects lipid oxidation and total volatiles of irradiated raw turkey meat

International Nuclear Information System (INIS)

Ahn, D.U.; Sell, J.L.; Jeffery, M.; Jo, C.; Chen, X.; Lee, J.I.

1997-01-01

Breast and leg meat patties, prepared from turkeys fed diets containing 25, 200, 400 or 600 IU of dl-alpha-tocopheryl acetate (TA) per kg diet, were irradiated at 0 or 2.5 kGy with vacuum or loose packaging. The effects of dietary TA on storage stability and production of volatiles in irradiated raw turkey meat were determined. Dietary TA at 200 IU/kg decreased lipid oxidation and reduced total volatiles of raw turkey patties after 7-days of storage. However, the antioxidant effects of dietary TA were more notable when the patties were loosely packaged than when vacuum-packaged. Irradiation increased lipid oxidation of raw turkey meats only when loosely packaged but had limited effects on formation of total volatiles after storage at 4 degrees C for 7 days or longer

Synchrotron X-ray diffraction investigations on strains in the oxide layer of an irradiated Zircaloy fuel cladding

Energy Technology Data Exchange (ETDEWEB)

Chollet, Mélanie, E-mail: melanie.chollet@psi.ch [Paul Scherrer Institute, NES, 5232 Villigen (Switzerland); Valance, Stéphane; Abolhassani, Sousan; Stein, Gene [Paul Scherrer Institute, NES, 5232 Villigen (Switzerland); Grolimund, Daniel [Paul Scherrer Institute, SLS, 5232 Villigen (Switzerland); Martin, Matthias; Bertsch, Johannes [Paul Scherrer Institute, NES, 5232 Villigen (Switzerland)

2017-05-15

For the first time the microstructure of the oxide layer of a Zircaloy-2 cladding after 9 cycles of irradiation in a boiling water reactor has been analyzed with synchrotron micro-X-ray diffraction. Crystallographic strains of the monoclinic and to some extent of the tetragonal ZrO{sub 2} are depicted through the thick oxide layer. Thin layers of sub-oxide at the oxide-metal interface as found for autoclave-tested samples and described in the literature, have not been observed in this material maybe resulting from irradiation damage. Shifts of selected diffraction peaks of the monoclinic oxide show that the uniform strain produced during oxidation is orientated in the lattice and displays variations along the oxide layer. Diffraction peaks and their shifts from families of diffracting planes could be translated into a virtual tensor. This virtual tensor exhibits changes through the oxide layer passing by tensile or compressive components. - Highlights: •A Zircaloy-2 cladding irradiated 9 cycles was investigated thanks to synchrotron X-ray diffraction. •Microstructure and uniform strain through the oxide layer is revealed. •The m-ZrO{sub 2} uniform strain is oriented presenting compression along the (−111) plane. •Virtual tensor is built based on reflecting planes of families of grains. •Tensor components vary from tensile to compressive along the oxide layer.

Synchrotron X-ray diffraction investigations on strains in the oxide layer of an irradiated Zircaloy fuel cladding

International Nuclear Information System (INIS)

Chollet, Mélanie; Valance, Stéphane; Abolhassani, Sousan; Stein, Gene; Grolimund, Daniel; Martin, Matthias; Bertsch, Johannes

2017-01-01

For the first time the microstructure of the oxide layer of a Zircaloy-2 cladding after 9 cycles of irradiation in a boiling water reactor has been analyzed with synchrotron micro-X-ray diffraction. Crystallographic strains of the monoclinic and to some extent of the tetragonal ZrO 2 are depicted through the thick oxide layer. Thin layers of sub-oxide at the oxide-metal interface as found for autoclave-tested samples and described in the literature, have not been observed in this material maybe resulting from irradiation damage. Shifts of selected diffraction peaks of the monoclinic oxide show that the uniform strain produced during oxidation is orientated in the lattice and displays variations along the oxide layer. Diffraction peaks and their shifts from families of diffracting planes could be translated into a virtual tensor. This virtual tensor exhibits changes through the oxide layer passing by tensile or compressive components. - Highlights: •A Zircaloy-2 cladding irradiated 9 cycles was investigated thanks to synchrotron X-ray diffraction. •Microstructure and uniform strain through the oxide layer is revealed. •The m-ZrO 2 uniform strain is oriented presenting compression along the (−111) plane. •Virtual tensor is built based on reflecting planes of families of grains. •Tensor components vary from tensile to compressive along the oxide layer.

Transmission electron microscopy study of the heavy-ion-irradiation-induced changes in the nanostructure of oxide dispersion strengthened steels

Science.gov (United States)

Rogozhkin, S. V.; Bogachev, A. A.; Orlov, N. N.; Korchuganova, O. A.; Nikitin, A. A.; Zaluzhnyi, A. G.; Kozodaev, M. A.; Kulevoy, T. V.; Kuibeda, R. P.; Fedin, P. A.; Chalykh, B. B.; Lindau, R.; Hoffman, Ya.; Möslang, A.; Vladimirov, P.; Klimenkov, M.

2017-07-01

Transmission electron microscopy was used to study the effect of heavy-ion irradiation on the structure and the phase state of three oxide dispersion strengthened (ODS) steels: ODS Eurofer, ODS 13.5Cr, and ODS 13.5Cr-0.3Ti (wt %). Samples were irradiated with iron and titanium ions to fluences of 1015 and 3 × 1015 cm-2 at 300, 573, and 773 K. The study of the region of maximum radiation damage shows that irradiation increases the number density of oxide particles in all samples. The fraction of fine inclusions increases in the particle size distribution. This effect is most pronounced in the ODS 13.5Cr steel irradiated with titanium ions at 300 K to a fluence of 3 × 1015 cm-2. It is demonstrated that oxide inclusions in ODS 13.5Cr-0.3Ti and ODS 13.5Cr steels are more stable upon irradiation at 573 and 773 K than upon irradiation at 300 K.

Vaporization studies on elemental tellurium and selenium by Knudsen effusion mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, R., E-mail: rvis1953@gmail.com; Balasubramanian, R., E-mail: rbs@igcar.gov.in; Darwin Albert Raj, D., E-mail: darwinalbertraj1953@gmail.com; Sai Baba, M., E-mail: msb@igcar.gov.in; Lakshmi Narasimhan, T.S., E-mail: tslak@igcar.gov.in

2014-08-01

Highlights: • A detailed KEMS study of vaporization of elemental tellurium and selenium systems. • Clusters Te{sub i}(g) (i = 2 to 7) and Se{sub i}(g) (i = 2 to 9) identified over Te(s) and Se(s). • p–T relations for Te{sub i}(g) (590 to 690 K) and Se{sub i}(g) (380 to 480 K). • Vapor phase of Te dominated by Te{sub 2}(g) (∼95%) while that of Se by Se{sub 6}(g) (∼50%) and Se{sub 5}(g) (∼25%). • Sublimation and atomization enthalpies deduced for Te{sub i}(g) and Se{sub i}(g). - Abstract: Vaporization studies on elemental tellurium and selenium were conducted by Knudsen effusion mass spectrometry in the temperature range of 590–690 K and 380–480 K, respectively. The ionic species Te{sub i}{sup +} (i = 1–7) and Se{sub i}{sup +}(g) (i = 1–9) were detected in the mass spectra over these two condensed phases. Measurement of ion intensities were performed as a function of electron impact energy and as a function of temperature (at different electron impact energies) for identifying the gaseous precursor species as well as for determining the partial pressure–temperature relations and sublimation enthalpies for these species. While the major species over elemental tellurium was confirmed to be Te{sub 2}(g) (with all other gaseous species Te{sub 3}–Te{sub 7} put together constituting less than 5%), the major species over elemental selenium was found to be Se{sub 6}(g), closely followed by Se{sub 5}(g) (with other gaseous species Se{sub 2}–Se{sub 4} and Se{sub 7}–Se{sub 9} put together also moderately constituting ∼25%). From the partial pressures, the thermodynamic data for the sublimation reactions i Te(s) = Te{sub i}(g) and i Se(s) = Se{sub i}(g) were deduced by second- and third-law methods. The atomization enthalpies of tellurium and selenium clusters were also deduced by using the recommended enthalpies of formation of monomeric species. Comparison of the findings obtained in the present study with those in previous studies revealed

Enrichment mechanisms of tellurium in ferromanganese crusts

Science.gov (United States)

Sakaguchi, A.; Sugiyama, T.; Usui, A.; Takahashi, Y.

2012-04-01

Marine ferromanganese crusts (FMCs) consist of iron (Fe) hydroxides and manganese (Mn) oxides with various minor and trace elements. Especially for tellurium (Te), which is recognized as one of the rare metals, it has been reported that this element is concentrated about 105 times in FMCs compared with earth's crust, and the host phase might be Fe (oxy)hydroxide (Hein et al., 2003). Actually, in our previous study, the high concentration of Te in very surface layers of FMCs was found from the top to halfway down of a seamount in the Pacific Ocean. However, the concentration of Te in surface layers through the seamount showed good correlation with that of Mn instead of Fe. In this study, we attempted to clarify the enrichment mechanism of Te in FMCs with some methods including X-ray absorption fine structure (XAFS) technique for synthesised /natural samples. Seventeen FMC samples were collected from the Takuyo-Daigo seamount, from 950 m (summit) to 3000 m in water depth, with hyper-dolphin (remotely operated vehicle) equipped with live video camera and manipulators. The growth rates of all FMC samples were estimated to be about 3 mm/Ma. Very surface layer (less than 1 mm) of all FMC was analyzed with XRD and XAFS to confirm the mineral composition and speciation of Te. Furthermore, to serve as an aid to clarify the adsorption mechanism of Te on FMCs, distribution coefficients (Kd) and oxidation states were determined through the adsorption experiments of Te(IV) and Te(VI) on ferrihydrite and δ-MnO2. In all the experiments, pH and ionic strength were adjusted to pH 7.5 and 0.7 M, respectively. The oxidation state of Te in water phase was determined with HPLC-ICP-MS. As for the analysis of oxidation and adsorption states on the solid phase, XAFS was employed. The major mineral composition of Fe and Mn had no significant variation through the water depth of Takuyo-Daigo seamount. The oxidation state of Te in all samples showed hexavalent, and there was no significant

Transesterification of used vegetable oil catalyzed by barium oxide under simultaneous microwave and ultrasound irradiations

International Nuclear Information System (INIS)

Martinez-Guerra, Edith; Gude, Veera Gnaneswar

2014-01-01

Graphical abstract: Transesterification reaction mediated by simultaneous microwave and ultrasound irradiations with barium oxide (BaO) heterogeneous catalyst. - Highlights: • Synergistic effect of simultaneous microwave/ultrasound irradiations was evaluated. • Yields were higher for the MW/US reactions compared to MW or US individually. • BaO catalyzed MW/US transesterification reaction is more environmental-friendly. • BaO catalyzed MW/US transesterification reaction provides better biodiesel yields. • Optimum power density must be identified for energy-efficient biodiesel production. - Abstract: This study presents a novel application of simultaneous microwave and ultrasound (MW/US) irradiations on transesterification of used vegetable oil catalyzed by barium oxide, heterogeneous catalyst. Experiments were conducted to study the optimum process conditions, synergistic effect of microwave and ultrasound irradiations and the effect of power density. From the process parametric optimization study, the following conditions were determined as optimum: 6:1 methanol to oil ratio, 0.75% barium oxide catalyst by wt.%, and 2 min of reaction time at a combined power output rate of 200 W (100/100 MW/US). The biodiesel yields were higher for the simultaneous MW/US mediated reactions (∼93.5%) when compared to MW (91%) and US (83.5%) irradiations individually. Additionally, the effect of power density and a discussion on the synergistic effect of the microwave and ultrasound mediated reactions were presented. A power density of 7.6 W/mL appears to be effective for MW, and MW/US irradiated reactions (94.4% and 94.7% biodiesel yields respectively), while a power density of 5.1 W/mL was appropriate for ultrasound irradiation (93.5%). This study concludes that the combined microwave and ultrasound irradiations result in a synergistic effect that reduces the heterogeneity of the transesterification reaction catalyzed by heterogeneous catalysts to enhance the biodiesel

Iodine-131 production by a dry method using reactor-irradiated elementary tellurium. Part 1 - Conditions for obtaining iodine emanation and its capture. Part 2 - comparative study of preparation conditions using Pyrex, stainless steel and alumina equipment. Part 3 - production on a semi-industrial scale; Production de l'iode 131 par voie seche a partir de tellure elementaire irradie a la pile. 1ere partie - Etudes des conditions pour obtenir l'emanation de l'iode et le capter. 2eme partie - Etude comparee des conditions pour effectuer cette preparation avec des appareils en Pyrex, en acier inoxydable et en alumine. 3eme partie - production a l'echelle semi-industrielle

Energy Technology Data Exchange (ETDEWEB)

Bardy, A; Beydon, J; Murthy, T S; Doyen, J B; Lefrancois, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-04-15

A previous report has described how iodine 131 can be prepared from elementary tellurium by a dry method which consists in treating irradiated tellurium at 400 degrees in argon. The possibility of carrying out this treatment in a stainless steel or alumina apparatus has been considered. The behavior of gaseous iodine 131 towards these materials has thus been studied. If the adsorption of iodine on stainless steel is superficial desorption is rapid at 250 degrees in oxygen or 400 degrees in argon. If the adsorption is chemical in nature it becomes necessary to heat to higher temperatures. Adsorption of iodine on alumina is very weak and the iodine can be desorbed rapidly. With these materials tests have been carried out on 300 gms of tellurium containing 41 curies of iodine 131; the yields were very satisfactory ( 98 per cent). (author) [French] La methode de preparation de l iode 131 par voie seche a partir de tellure elementaire decrite dans un precedent rapport consiste a traiter le tellure irradie a 400 degres sous argon. Nous avons examine la possibilite d effectuer ce traitement dans un appareil en acier inoxidable ou en alumine. Le comportement de l iode 131 gazeux vis a vis de ces materiaux a donc ete etudie. Si l adsorption de l iode sur l acier inoxidable est superficielle la desorption est rapide a 250 degres sous oxygene ou 400 degres sous argon. Si la fixation est de nature chimique il est necessaire de chauffer a des temperatures plus elevees. L adsorption de l iode sur l alumine est res faible et l iode peut etre desorbe rapideemnt. En employant ces materiaux des essais ont ete obtenus sur 300 g de tellure contenant 41 curies d iode 131 avec un bon rendement (98 pour cent). (auteur00.

Positron annihilation study of defects in electron-irradiated single crystal zinc oxide

Science.gov (United States)

To, C. K.; Yang, B.; Beling, C. D.; Fung, S.; Ling, C. C.; Gong, M.

2011-01-01

Pressurized melt grown zinc oxide (ZnO) single crystals purchased from Cermet Inc. were irradiated by 2MeV electrons with fluence of 6x1017cm-2. Isochronal annealing from 100°C-800°C was performed on the crystals under argon and air ambience. Variable Energy Doppler Broadening Spectroscopy (VEDBS) was carried out on both the as-grown and the irradiated samples at each annealing step. The migration, agglomeration and annealing of grown-in and irradiated-introduced defects were studied. It was observed that the grown-in vacancy-type defects concentration decreased at 300°C and 600 °C. For the irradiated sample annealed in argon, the positron trapping vacancy-type defect concentration decreased at 300°C and 600°C. Further annealing the as-grown and irradiated samples in argon increased the S parameter further. For the irradiated sample annealed in air, the vacancy-type defect concentration decreases at 300°C and 700°C.

Positron annihilation study of defects in electron-irradiated single crystal zinc oxide

Energy Technology Data Exchange (ETDEWEB)

To, C K; Yang, B; Beling, C D; Fung, S; Ling, C C [Department of Physics, University of Hong Kong (Hong Kong); Gong, M, E-mail: sfung@hkucc.hku.h, E-mail: edwardto04@yahoo.com.h [Department of Physics, Sichuan University, Chengdu (China)

2011-01-01

Pressurized melt grown zinc oxide (ZnO) single crystals purchased from Cermet Inc. were irradiated by 2 MeV electrons with fluence of 6x10{sup 17}cm{sup -2}. Isochronal annealing from 100 deg. C - 800 deg. C was performed on the crystals under argon and air ambience. Variable Energy Doppler Broadening Spectroscopy (VEDBS) was carried out on both the as-grown and the irradiated samples at each annealing step. The migration, agglomeration and annealing of grown-in and irradiated-introduced defects were studied. It was observed that the grown-in vacancy-type defects concentration decreased at 300 deg. C and 600 deg. C. For the irradiated sample annealed in argon, the positron trapping vacancy-type defect concentration decreased at 300 deg. C and 600 deg. C. Further annealing the as-grown and irradiated samples in argon increased the S parameter further. For the irradiated sample annealed in air, the vacancy-type defect concentration decreases at 300 deg. C and 700 deg. C.

Positron annihilation study of defects in electron-irradiated single crystal zinc oxide

International Nuclear Information System (INIS)

To, C K; Yang, B; Beling, C D; Fung, S; Ling, C C; Gong, M

2011-01-01

Pressurized melt grown zinc oxide (ZnO) single crystals purchased from Cermet Inc. were irradiated by 2 MeV electrons with fluence of 6x10 17 cm -2 . Isochronal annealing from 100 deg. C - 800 deg. C was performed on the crystals under argon and air ambience. Variable Energy Doppler Broadening Spectroscopy (VEDBS) was carried out on both the as-grown and the irradiated samples at each annealing step. The migration, agglomeration and annealing of grown-in and irradiated-introduced defects were studied. It was observed that the grown-in vacancy-type defects concentration decreased at 300 deg. C and 600 deg. C. For the irradiated sample annealed in argon, the positron trapping vacancy-type defect concentration decreased at 300 deg. C and 600 deg. C. Further annealing the as-grown and irradiated samples in argon increased the S parameter further. For the irradiated sample annealed in air, the vacancy-type defect concentration decreases at 300 deg. C and 700 deg. C.

Structural and morphological changes in pseudobarrier films of anodic aluminum oxide caused by irradiation with high-energy particles

International Nuclear Information System (INIS)

Chernykh, M.A.; Belov, V.T.

1988-01-01

We have studied the structural and morphological changes, occurring under the electron beam in pseudobarrier films of anodic aluminum oxide, prepared in seven different solutions and irradiated beforehand by protons of x-rays, with the aim of elucidating the structure of anodic aluminum oxides. An increased stability of the pseudobarrier films of anodic aluminum oxide has been observed towards the action of the electron beam of an UEMV-100K microscope at standard working regimes (75 keV) as a result of irradiation with protons or x-rays. A difference has been found to exist between structural and morphological changes of anodic aluminum oxide films, prepared in different solutions, when irradiated with high-energy particles. A structural and phase inhomogeneity of amorphous pseudobarrier films of anodic aluminum oxide has been detected and its influence on the character of solid-phase transformations under the maximum-intensity electron beam

Texture, color, lipid oxidation and sensory acceptability of gamma-irradiated marinated anchovy fillets

Science.gov (United States)

Tomac, Alejandra; Cova, María C.; Narvaiz, Patricia; Yeannes, María I.

2015-01-01

The effect of gamma irradiation (0, 2, 3 and 4 kGy) on vacuum-packed marinated anchovy fillets was analyzed for their texture, color, lipid oxidation and sensory acceptability after 10 months under refrigeration. Marinated (3% acetic acid, 10% sodium chloride and 0.2% citric acid) Engraulis anchoita fillets were vacuum-packed and irradiated with a cobalt-60 source at a semi-industrial irradiation facility. The irradiation caused a slight increase in hardness values regardless of the applied dose but maintained a consistent texture over the 10 months, even though the control samples softened, most likely due to degradation. This hardness increase did not affect the textural sensory acceptability. Irradiation did not modify the color but still reduced color changes during storage, benefitting the product's quality. TBARS was increased in every sample throughout storage, but irradiation decreased these values. Sensory acceptability was not affected by gamma irradiation. Therefore, gamma irradiation could be successfully applied to this type of product for the purpose of shelf-life extension.

Structural-morphological variations in pseudo-barrier films of anode aluminium oxide under irradiation with high-energy particles

International Nuclear Information System (INIS)

Chernykh, M.A.; Belov, V.T.

1988-01-01

Comparative study of structural-morphological variations under electron beam effect in pseudo-barrier films of anode aluminium oxide, obtained in seven different solutions and proton or X-rays pre-irradiated to determine structure peculiarities of anode aluminium oxides, is presented. Such study is a matter of interest from the solid-phase transformation theory point of view and for anode aluminium films application under radiation. Stability increase of pseudo-barrier films of anode aluminium oxide to the effect of UEhMV-100 K microscope electron beam at standard modes of operation (75 kV) due to proton or X-rays irradiation is found. Difference in structural-monorphological variations obtained in different solutions of anode aluminium films under high-energy particles irradiation is determined. Strucural-phase microinhomogeneity of amorphous pseudo-barrier films of anode aluminium oxide and its influence on solid-phase transformations character under electron bean of maximal intensity are detected

Correlation between locally deformed structure and oxide film properties in austenitic stainless steel irradiated with neutrons

Energy Technology Data Exchange (ETDEWEB)

Chimi, Yasuhiro, E-mail: chimi.yasuhiro@jaea.go.jp [Japan Atomic Energy Agency (JAEA), 2-4 Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Kitsunai, Yuji [Nippon Nuclear Fuel Development, 2163 Narita-cho, Oarai-machi, Higashi-ibaraki-gun, Ibaraki 311-1313 (Japan); Kasahara, Shigeki [Japan Atomic Energy Agency (JAEA), 2-4 Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Chatani, Kazuhiro; Koshiishi, Masato [Nippon Nuclear Fuel Development, 2163 Narita-cho, Oarai-machi, Higashi-ibaraki-gun, Ibaraki 311-1313 (Japan); Nishiyama, Yutaka [Japan Atomic Energy Agency (JAEA), 2-4 Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan)

2016-07-15

To elucidate the mechanism of irradiation-assisted stress corrosion cracking (IASCC) in high-temperature water for neutron-irradiated austenitic stainless steels (SSs), the locally deformed structures, the oxide films formed on the deformed areas, and their correlation were investigated. Tensile specimens made of irradiated 316L SSs were strained 0.1%–2% at room temperature or at 563 K, and the surface structures and crystal misorientation among grains were evaluated. The strained specimens were immersed in high-temperature water, and the microstructures of the oxide films on the locally deformed areas were observed. The appearance of visible step structures on the specimens' surface depended on the neutron dose and the applied strain. The surface oxides were observed to be prone to increase in thickness around grain boundaries (GBs) with increasing neutron dose and increasing local strain at the GBs. No penetrative oxidation was observed along GBs or along surface steps. - Highlights: • Visible step structures depend on the neutron dose and the applied strain. • Local strain at grain boundaries was accumulated with the neutron dose. • Oxide thickness increases with neutron dose and local strain at grain boundaries. • No penetrative oxidation was observed along grain boundaries or surface steps.

Synthesis and characterization of some metal oxide nanocrystals by microwave irradiation

Energy Technology Data Exchange (ETDEWEB)

Rashad, M.; Gaber, A.; Abdelrahim, M. A.; Abdel-Baset, A. M. [Physics Department, Faculty of Science, Assiut University, 71516 Assiut (Egypt); Moharram, A. H. [Physics Dept., College of Science and Arts, King Abdulaziz Univ., Rabigh 21911 (Saudi Arabia)

2013-12-16

Copper oxide and cobalt oxide (CuO, Co3O4) nanocrystals (NCs) have been successfully prepared in a short time using microwave irradiation. The resulted powders of nanocrystals (NCs) were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Thermogravimetric analysis (TGA) measurements are also studied. Fourier-transform infrared (FT-IR) and UV–visible absorption spectroscopy of both kind of nanoparticels are illustrated. Optical absorption analysis indicated the direct band gap for both kinds of nanocrystals.

Laser effects on graphene oxide irradiated in high vacuum

Czech Academy of Sciences Publication Activity Database

Torrisi, L.; Silipigni, L.; Cutroneo, Mariapompea

2018-01-01

Roč. 173, 1-2 (2018), s. 73-84 ISSN 1042-0150 R&D Projects: GA MŠk LM2015056; GA ČR GA16-05167S Institutional support: RVO:61389005 Keywords : graphene oxide * laser irradiation * laser-generated plasma * radiation effects Subject RIV: BL - Plasma and Gas Discharge Physics OBOR OECD: Fluids and plasma physics (including surface physics) Impact factor: 0.443, year: 2016

Formation of porous silicon oxide from substrate-bound silicon rich silicon oxide layers by continuous-wave laser irradiation

Science.gov (United States)

Wang, Nan; Fricke-Begemann, Th.; Peretzki, P.; Ihlemann, J.; Seibt, M.

2018-03-01

Silicon nanocrystals embedded in silicon oxide that show room temperature photoluminescence (PL) have great potential in silicon light emission applications. Nanocrystalline silicon particle formation by laser irradiation has the unique advantage of spatially controlled heating, which is compatible with modern silicon micro-fabrication technology. In this paper, we employ continuous wave laser irradiation to decompose substrate-bound silicon-rich silicon oxide films into crystalline silicon particles and silicon dioxide. The resulting microstructure is studied using transmission electron microscopy techniques with considerable emphasis on the formation and properties of laser damaged regions which typically quench room temperature PL from the nanoparticles. It is shown that such regions consist of an amorphous matrix with a composition similar to silicon dioxide which contains some nanometric silicon particles in addition to pores. A mechanism referred to as "selective silicon ablation" is proposed which consistently explains the experimental observations. Implications for the damage-free laser decomposition of silicon-rich silicon oxides and also for controlled production of porous silicon dioxide films are discussed.

Effects of soy sauce and packaging method on volatile compounds and lipid oxidation of cooked irradiated beef patties

Science.gov (United States)

Kim, Hyun-Wook; Lee, Soo-Yeon; Hwang, Ko-Eun; Song, Dong-Heon; Kim, Yong-Jae; Ham, Yun-Kyung; Lee, Choong-Hee; Choi, Yun-Sang; Lee, Ju-Woon; Kim, Cheon-Jei

2014-10-01

The objective of this study is to determine the effect of soy sauce on volatile compounds and lipid oxidation of cooked irradiated beef patties. Sulfur-containing volatile components, which are produced by irradiation, were not found in all treatments. Volatile components derived from soy sauce, such as 3-hydroxy-2-butanone, acetic acid, 3-methyl-1-butanol and 2-methyl-1-butanol, were detected in beef patties containing soy sauce regardless of irradiation and packaging method. Volatile aldehydes, including hexanal, significantly decreased the irradiated beef patty prepared with soy sauce compared to those of irradiated beef patty made with NaCl at 1 day and 5 days after irradiation. In addition, combined use of vacuum packaging and soy sauce treatments could inhibit the formation of volatile compounds and 2-thiobarbituric acid reactive substances during chilled storage. Therefore, the use of soy sauce in cooked and irradiated beef could reduce the production of volatile components associated with the irradiation-induced off-flavor and lipid oxidation.

Advanced Oxidation Treatment of Drinking Water and Wastewater Using High-energy Electron Beam Irradiation

Directory of Open Access Journals (Sweden)

Abbas Behjat

2007-03-01

Full Text Available Application of electron beam as a strong oxidation method for disinfection of drinking water and wastewater has been investigated. Drinking water samples were prepared from wells in rock zones in Yazd Province. Wastewater samples were collected from Yazd Wastewater Treatment Plant. Samples were irradiated by 10 MeV electron beam accelerator at Yazd Radiation Processing Center. The irradiation dose range varied from 0.5-5 kGy. Biological parameters and microbial agents such as aerobic mesophiles and coliforms including E. coli count before and after irradiation versus irradiation dose were obtained using MPN method. The data obtained from irradiated water and wastewater were compared with un-irradiated (control samples. The results showed a removal of 90% of all microorganisms at irradiation doses below 5 kGy, suggesting electron beam irradiation as an effective method for disinfection of wastewater.

Synthesis of ultra-thin tellurium nanoflakes on textiles for high-performance flexible and wearable nanogenerators

Energy Technology Data Exchange (ETDEWEB)

He, Wen; Van Ngoc, Huynh; Qian, Yong Teng; Hwang, Jae Seok; Yan, Ya Ping [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of); Choi, Hongsoo [Department of Robotics Engineering, Daegu Gyeongbuk Institute of Science and Technology (DGIST), 711-873, Daegu (Korea, Republic of); Kang, Dae Joon, E-mail: djkang@skku.edu [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of)

2017-01-15

Highlights: • Ultra-thin tellurium (Te) nanoflakes were successfully grown on textile and used as an active piezoelectric material. • Te nanoflake nanogenerator device was systematically studied by bending and compressing test. • The ultra-high output power during compressing test can light up 10 LEDs without any external power source. • The device can offer a breakthrough in applying tellurium nanoflakes into high-performance flexible and wearable piezoelectric nanogenerator. - Abstract: We report that ultra-thin tellurium (Te) nanoflakes were successfully grown on a sample of a gold-coated textile, which then was used as an active piezoelectric material. An output voltage of 4 V and a current of 300 nA were obtained from the bending test under a driving frequency of 10 Hz. To test the practical applications, Te nanoflake nanogenerator (TFNG) device was attached to the subject’s arm, and mechanical energy was converted to electrical energy by means of periodic arm-bending motions. The optimized open-circuit voltage and short-circuit current density of approximately 125 V and 17 μA/cm{sup 2}, respectively, were observed when a TFNG device underwent a compression test with a compressive force of 8 N and driving frequency of 10 Hz. This high-power generation enabled the instantaneous powering of 10 green light-emitting diodes that shone without any assistance from an external power source.

Equilibrium evaporation behavior of polonium and its homologue tellurium in liquid lead-bismuth eutectic

International Nuclear Information System (INIS)

Ohno, Shuji; Miyahara, Shinya; Kurata, Yuji; Katsura, Ryoei; Yoshida, Shigeru

2006-01-01

Experimental study using the transpiration method investigates equilibrium evaporation behavior of radionuclide polonium ( 210 Po) generated and accumulated in liquid lead-bismuth eutectic (LBE) cooled nuclear systems. The experiment consists of two series of tests: preliminary evaporation tests for homologue element tellurium (Te) in LBE, and evaporation tests for 210 Po-accumulated LBE in which test specimens are prepared by neutron irradiation. The evaporation tests of Te in LBE provide the suggestion that Te exists in a chemical form of PbTe as well as the information for confirming the validity of technique and conditions of Po test. From the evaporation tests of 210 Po in LBE, we obtain fundamental data and empirical equations such as 210 Po vapor concentration in the gas phase, 210 Po partial vapor pressure, thermodynamic activity coefficients, and gas-liquid equilibrium partition coefficient of 210 Po in LBE in the temperature range from 450 to 750degC. Additionally, radioactivity concentration of 210 Po and 210m Bi vapor in a cover gas region of a typical LBE-cooled nuclear system is specifically estimated based on the obtained experimental results, and the importance of 210 Po evaporation behavior is quantitatively demonstrated. (author)

Metal adsorption of gamma-irradiated carboxymethyl cellulose/polyethylene oxide blend films

Science.gov (United States)

El-Naggar, Amal A.; Magida, M. M.; Ibrahim, Sayeda M.

2016-03-01

Blend films of different ratios of carboxymethyl cellulose (CMC)/polyethylene oxide (PEO) were prepared by the solution casting method. To investigate the effect of irradiation on all properties of prepared blend, it was exposed to different gamma irradiation doses (10, 20, and 30 kGy). Physical properties such as gel fraction (GF) (%) and swelling (SW) (%) were investigated. It was found that the GF (%) increases with increasing irradiation dose up to 20 kGy, while SW (%) decreases with an increase in the irradiation doses for all blend compositions. Moreover, the structural and mechanical properties of the prepared films were studied. The results of the mechanical properties obtained showed that there is an improvement in these properties with an increase in both CMC and irradiation dose up to 20 kGy. The efficiency of metal ions uptake was measured using a UV spectrophotometer. The prepared films showed good tendency to absorb and release metal ions from aqueous media. Thus, the CMC/PEO film can be used in agricultural domain.

Radiation response of ODS ferritic steels with different oxide particles under ion-irradiation at 550 °C

Science.gov (United States)

Song, Peng; Morrall, Daniel; Zhang, Zhexian; Yabuuchi, Kiyohiro; Kimura, Akihiko

2018-04-01

In order to investigate the effects of oxide particles on radiation response such as hardness change and microstructural evolution, three types of oxide dispersion strengthened (ODS) ferritic steels (named Y-Ti-ODS, Y-Al-ODS and Y-Al-Zr-ODS), mostly strengthened by Y-Ti-O, Y-Al-O and Y-Zr-O dispersoids, respectively, were simultaneously irradiated with iron and helium ions at 550 °C up to a damage of 30 dpa and a corresponding helium (He) concentration of ∼3500 appm to a depth of 1000-1300 nm. A single iron ion beam irradiation was also performed for reference. Transmission electron microscopy revealed that after the dual ion irradiation helium bubbles of 2.8, 6.6 and 4.5 nm in mean diameter with the corresponding number densities of 1.1 × 1023, 2.7 × 1022 and 3.6 × 1022 m-3 were observed in Y-Ti-ODS, Y-Al-ODS and Y-Al-Zr-ODS, respectively, while no such bubbles were observed after single ion irradiation. About 80% of intragranular He bubbles were adjacent to oxide particles in the ODS ferritic steels. Although the high number density He bubbles were observed in the ODS steels, the void swelling in Y-Ti-ODS, Y-Al-ODS and Y-Al-Zr-ODS was still small and estimated to be 0.13%, 0.53% and 0.20%, respectively. The excellent swelling resistance is dominantly attributed to the high sink strength of oxide particles that depends on the morphology of particle dispersion rather than the crystal structure of the particles. In contrast, no dislocation loops were produced in any of the irradiated steels. Nanoindentation measurements showed that no irradiation hardening but softening was found in the ODS ferritic steels, which was probably due to irradiation induced dislocation recovery. The helium bubbles in high number density never contributed to the irradiation hardening of the ODS steels at these irradiation conditions.

LYCOPENE EFFICIENCY IN THE MODULATION OF OXIDATIVE DAMAGE IN DIFFERENT TISSUES OF GAMMA IRRADIATED RATS

International Nuclear Information System (INIS)

EL-TAHAWY, N.A.; NADA, A.S.; REZK, R.G.

2008-01-01

Exposure to ionizing radiation induces oxidative stress that has been recognized as an important etiological factor in the causation of several chronic diseases. Lycopene, a carotenoid almost exclusively present in tomatoes and tomatoes products, is a lipid soluble antioxidant claimed to possess cardio protective and anticancer properties. The present study was designed to determine the possible modulator effects of lycopene on radiation-induced oxidative damage to liver, spleen and lung tissues. Animals were supplemented with lycopene (5 mg/kg body weight/ day) by gavages for two weeks before whole body exposure to gamma rays and within the period of irradiation (3 successive doses, each of 3 Gy at 72 hours intervals). Animals were sacrificed on the 3 r d day post the last irradiation session.The results obtained in the present study showed that whole body gamma irradiation produced oxidative stress manifested by significant elevation in lipid peroxides levels measured as thiobarbituric acid reactive substances (TBARS) associated with significant decrease of nitric oxide (NO) content. Non-significant change in total cupper (Cu) in the three tissues was recorded while significant increase of total iron (Fe) was observed in liver and spleen tissues only. Liver tissue of irradiated rats showed significant decrease in the activities of the antioxidant enzymes as superoxide dismutase (SOD) and catalase (CAT). In spleen tissues, there was a significant increase of SOD and significant decrease of CAT activities while in lung tissues, both SOD and CAT activities showed significant increase.Histological observations of photomicrograph of liver sections showed that radiation-induced sever damage obvious by dilated portal vein, ruptured hepatocytes, necrotic, pyknotic, karyolitic nuclei and vacuolated cytoplasm. In spleen tissue, radiation was induced degeneration of lymphatic nodules, dilation follicular artery and marked hemorrhage. In lung tissue, radiation- induces ill

Primary oxidation and reduction products in x-irradiated aspartic acid

International Nuclear Information System (INIS)

Adams, S.M.; Budzinski, E.E.; Box, H.C.

1976-01-01

The primary reduction products identified by ESR--ENDOR spectroscopy in single crystals of DL-aspartic acid hydrochloride irradiated at 4.2degreeK are anions formed by addition of an electron to the carbonyl oxygen atoms of the carboxylic acid groups. The main consequence of the oxidation process is to produce a hole centered mainly on atomic chlorine

Oxidative decomposition of aromatic hydrocarbons by electron beam irradiation

Science.gov (United States)

Han, Do-Hung; Stuchinskaya, Tatiana; Won, Yang-Soo; Park, Wan-Sik; Lim, Jae-Kyong

2003-05-01

Decomposition of aromatic volatile organic compounds (VOCs) under electron beam irradiation was studied in order to examine the kinetics of the process, to characterize the reaction product distribution and to develop a process of waste gas control technology. Toluene, ethylbenzene, o-, m-, p-xylenes and chlorobenzene were used as target materials. The experiments were carried out at doses ranging from 0.5 to 10 kGy, using a flow reactor utilized under electron beam irradiation. Maximum degrees of decomposition carried out at 10 kGy in air environment were 55-65% for “non-chlorinated” aromatic VOC and 85% for chlorobenzene. It was found that a combination of aromatic pollutants with chlorobenzene would considerably increase the degradation value up to nearly 50% compared to the same compounds in the absence of chlorine groups. Based on our experimental observation, the degradation mechanism of the aromatic compounds combined with chloro-compound suggests that a chlorine radical, formed from EB irradiation, induces a chain reaction, resulting in an accelerating oxidative destruction of aromatic VOCs.

Nano lead oxide and epdm composite for development of polymer based radiation shielding material: Gamma irradiation and attenuation tests

Science.gov (United States)

Özdemir, T.; Güngör, A.; Akbay, I. K.; Uzun, H.; Babucçuoglu, Y.

2018-03-01

It is important to have a shielding material that is not easily breaking in order to have a robust product that guarantee the radiation protection of the patients and radiation workers especially during the medical exposure. In this study, nano sized lead oxide (PbO) particles were used, for the first time, to obtain an elastomeric composite material in which lead oxide nanoparticles, after the surface modification with silane binding agent, was used as functional material for radiation shielding. In addition, the composite material including 1%, 5%, 10%, 15% and 20% weight percent nano sized lead oxide was irradiated with doses of 81, 100 and 120 kGy up to an irradiation period of 248 days in a gamma ray source with an initial dose rate of 21.1 Gy/h. Mechanical, thermal properties of the irradiated materials were investigated using DSC, DMA, TGA and tensile testing and modifications in thermal and mechanical properties of the nano lead oxide containing composite material via gamma irradiation were reported. Moreover, effect of bismuth-III oxide addition on radiation attenuation of the composite material was investigated. Nano lead oxide and bismuth-III oxide particles were mixed with different weight ratios. Attenuation tests have been conducted to determine lead equivalent values for the developed composite material. Lead equivalent thickness values from 0.07 to 0.65 (2-6 mm sample thickness) were obtained.

Lipid oxidation, color changes and volatiles production in irradiated pork sausage with different fat content and packaging during storage

International Nuclear Information System (INIS)

Jo, C.; Lee, J.I.; Ahn, D.U.

1999-01-01

Effects of irradiation on lipid oxidation, color and volatiles production in pork sausages with different fat content and packaging were determined. Sausages (with 4.7, 10.5 and 15.8% fat content) were sliced and vacuum-packaged either in oxygen-permeable or impermeable bags, irradiated (0 or 4.5 kGy) and stored at 4°C for 7 days. Lipid oxidation, color and volatiles productions were analyzed at 0, 3 and 7 days of storage. TBARS (2-thiobarbituric acid reactive substances) values of cooked pork sausages increased with the increase of fat content regardless of storage, irradiation or packaging types. Irradiated samples had higher TBARS than nonirradiated at 0 day but the difference disappeared during storage in both packaging types. Lightness of sausages (Hunter L-value) increased with the increase of fat content and storage time but was not affected by irradiation. In aerobic packaging, irradiation reduced Hunter a-values of pork sausages at 0 day but irradiation effect on a-value disappeared during storage. In vacuum packaging, however, irradiated samples had higher Hunter a-values than nonirradiated samples. Irradiation increased 1-heptene and total volatiles, but the amount of 1-heptene was not associated well with TBARS values of pork sausages. In both irradiated and nonirradiated pork sausages, aerobic packaging produced more volatiles than vacuum packaging during storage. It was concluded that irradiation and fat content had significant effects on lipid oxidation, color and volatiles production of cooked pork sausages during storage but that oxygen availability had a stronger effect than irradiation and fat content

In Situ Spectroscopic Analysis of the Carbothermal Reduction Process of Iron Oxides during Microwave Irradiation

Directory of Open Access Journals (Sweden)

Jun Fukushima

2018-01-01

Full Text Available The effects of microwave plasma induction and reduction on the promotion of the carbothermal reduction of iron oxides (α-Fe2O3, γ-Fe2O3, and Fe3O4 are investigated using in situ emission spectroscopy measurements during 2.45 GHz microwave processing, and the plasma discharge (such as CN and N2 is measured during microwave E-field irradiation. It is shown that CN gas or excited CN molecules contribute to the iron oxide reduction reactions, as well as to the thermal reduction. On the other hand, no plasma is generated during microwave H-field irradiation, resulting in thermal reduction. Magnetite strongly interacts with the microwave H-field, and the reduction reaction is clearly promoted by microwave H-field irradiation, as well as thermal reduction reaction.

Determination of spins and radioactive widths of tellurium nuclear levels with capturre gamma rays

International Nuclear Information System (INIS)

Bianchini, F.G.

1973-01-01

Spins and levels widths of the tellurium, mainly 128 Te and 130 Te, were determinated by gamma spectroscopy. Measurements of inelastic and elastic scattering, angular distribution and scattering temperature dependence, were still made. Energy levels of this isotopes, were also determinated [pt

Structural evaluation of reduced graphene oxide in graphene oxide during ion irradiation: X-ray absorption spectroscopy and in-situ sheet resistance studies

Science.gov (United States)

Saravanan, K.; Jayalakshmi, G.; Suresh, K.; Sundaravel, B.; Panigrahi, B. K.; Phase, D. M.

2018-03-01

We report the structural evolution of reduced graphene oxide (rGO) in graphene oxide (GO) flakes during 1 MeV Si+ ion irradiation. In-situ electrical resistivity measurements facilitate monitoring the sheet resistance with the increase in the fluence. The electrical sheet resistance of the GO flake shows the exponential decay behaviour with the increasing ion fluence. Raman spectra of the GO flake reveal the increase in the ID/IG ratio, indicating restoration of the sp2 network upon irradiation. The C/O ratio estimated from resonant Rutherford backscattering spectrometry analysis directly evidenced the reduction of oxygen moieties upon irradiation. C K-edge X-ray absorption near edge structure spectra reveal the restoration of C=C sp2-hybridized carbon atoms and the removal of oxygen-containing functional groups in the GO flake. STM data reveal the higher conductance in the rGO regime in comparison with the regime, where the oxygen functional groups are present. The experimental investigation demonstrates that the ion irradiation can be employed for efficient reduction of GO with tunable electrical and structural properties.

Selenium and tellurium nanomaterials

Science.gov (United States)

Piacenza, Elena; Presentato, Alessandro; Zonaro, Emanuele; Lampis, Silvia; Vallini, Giovanni; Turner, Raymond J.

2018-04-01

Over the last 40 years, the rapid and exponential growth of nanotechnology led to the development of various synthesis methodologies to generate nanomaterials different in size, shape and composition to be applied in various fields. In particular, nanostructures composed of Selenium (Se) or Tellurium (Te) have attracted increasing interest, due to their intermediate nature between metallic and non-metallic elements, being defined as metalloids. Indeed, this key shared feature of Se and Te allows us the use of their compounds in a variety of applications fields, such as for manufacturing photocells, photographic exposure meters, piezoelectric devices, and thermoelectric materials, to name a few. Considering also that the chemical-physical properties of elements result to be much more emphasized when they are assembled at the nanoscale range, huge efforts have been made to develop highly effective synthesis methods to generate Se- or Te-nanomaterials. In this context, the present book chapter will explore the most used chemical and/or physical methods exploited to generate different morphologies of metalloid-nanostructures, focusing also the attention on the major advantages, drawbacks as well as the safety related to these synthetic procedures.

The resistance changes of carbon and metal oxide film resistors by irradiation of 60Co γ rays

International Nuclear Information System (INIS)

Okamoto, Shinichi; Fujino, Takahiro; Furuta, Junichiro; Yoshida, Toshio

1979-01-01

The resistance changes of glass-sealed deposited-carbon-film and carbon-coated-film resitors and metal oxide glazed resistors made in USA were studied by gamma-ray irradiation. (1) The resistances of deposited-carbon-film resistors of 50, 100 and 200 megohm did not change by irradiation of gamma rays up to 1.9 x 10 9 R. (2) The carbon-coated-film resistors of 100, 1000, 10000 and 100000 megohm had negative resistance changes by irradiation of gamma rays up to 9.9 x 10 8 R. (3) The resistances of metal oxide glazed resistors of 100, 1000 and 10000 megohm did not change by irradiation of gamma rays up to 8.8 x 10 8 R. When radiation monitoring instruments with hi-meg resistors are used in a gamma field with high intensity, the resistors must not be exposed to gamma rays with high doses, or the resistors which do not change by gamma-ray irradiation must be selected. (author)

Texture, color, lipid oxidation and sensory acceptability of gamma-irradiated marinated anchovy fillets

International Nuclear Information System (INIS)

Tomac, Alejandra; Cova, María C.; Narvaiz, Patricia; Yeannes, María I.

2015-01-01

The effect of gamma irradiation (0, 2, 3 and 4 kGy) on vacuum-packed marinated anchovy fillets was analyzed for their texture, color, lipid oxidation and sensory acceptability after 10 months under refrigeration. Marinated (3% acetic acid, 10% sodium chloride and 0.2% citric acid) Engraulis anchoita fillets were vacuum-packed and irradiated with a cobalt-60 source at a semi-industrial irradiation facility. The irradiation caused a slight increase in hardness values regardless of the applied dose but maintained a consistent texture over the 10 months, even though the control samples softened, most likely due to degradation. This hardness increase did not affect the textural sensory acceptability. Irradiation did not modify the color but still reduced color changes during storage, benefitting the product's quality. TBARS was increased in every sample throughout storage, but irradiation decreased these values. Sensory acceptability was not affected by gamma irradiation. Therefore, gamma irradiation could be successfully applied to this type of product for the purpose of shelf-life extension. - Highlights: • Marinated anchovies were γ-irradiated at 2, 3 and 4 kGy and stored at 4 °C (10 months). • Irradiation slightly hardened the texture and reduced its softening during storage. • Irradiated marinades had good sensory acceptability without differences with controls. • Irradiation improved the quality by reducing texture softening and color changes

Point defects and irradiation in oxides: simulations at the atomic scale

International Nuclear Information System (INIS)

Crocombette, J.P.

2005-12-01

The studies done by Jean-Paul Crocombette between 1996 and 2005 in the Service de Recherches de Metallurgie Physique of the Direction de l'Energie Nucleaire in Saclay are presented in this Habilitation thesis. These works were part of the material science researches on the ageing, especially under irradiation, of oxides of interest for the nuclear industry. In this context simulation studies at the atomic scale were performed on two elementary components of ageing under irradiation : point defects and displacement cascades ; using two complementary simulation techniques : ab initio electronic structure calculations and empirical potential molecular dynamics. The first part deals with point defects : self defects (vacancies or interstitials) or hetero-atomic dopants. One first recalls the energetics of such defects in oxides, the specific features of defects calculations and the expected accuracy of these calculations. Then one presents the results obtained on uranium dioxide, oxygen in silver and amorphous silica. The second part tackles the modelling of disintegration recoil nuclei in various?displacement cascades created by crystalline matrices for actinide waste disposal. Cascade calculations give access to the amorphization mechanisms under irradiation of these materials. One thus predicts that the amorphization in zircon takes place directly in the tracks whereas in lanthanum zirconate, the amorphization proceeds through the accumulation of point defects. Finally the prospects of these studies are discussed. (author)

Protective Effect of Low Dose Gamma Irradiation against Oxidative Damage in Rats Administrated with Ferric- Nitrilotriacetate

International Nuclear Information System (INIS)

Mansonr, S.Z.

2009-01-01

Many studies have demonstrated the beneficial adaptive response of low dose gamma-irradiation. Low dose gamma-irradiation (LDR) might be effective for the prevention of various reactive oxygen species-related diseases. Ferric nitrilotriacetate (Fe-NTA) is a strong oxidant, which generates highly reactive hydroxyl radical and causes injuries of various organs including the kidney and liver. This study was designed to investigate the ability of low dose gamma-irradiation to restrain Fe-NT A induced oxidative stress. Sprague Dawley male albino rats were subjected to low dose gamma-irradiation (50 cGy). Animals were challenged with Fe-NT A (9 mg Fe/kg body weight, intraperitoneally). Results showed that Fe-NTA enhances lipid peroxidation (LPx) accompanied with reduction in glutathione (GSH) content, antioxidant enzymes, viz., glutathione peroxidase (GPX), glutathione reductase (GR), superoxide dismutase (SOD), catalase (CAT) and phase-U metabolizing enzyme glutathione-S-transferase (GST). Fe-NTA also enhances the concentration of blood urea nitrogen (BUN) and serum creatinine as well as alanine aminotransferase (ALT), aspartate aminotransferase (AST) and gamma-glutamyl transpeptidase (GGT) activities. Exposure to low dose gamma- irradiation (3 h after Fe-NTA administration) resulted in a significant decrease in LPx, BUN, serum creatinine contents as well as ALT, AST and GGT enzyme activities. GSH content; GST and antioxidant enzymes were also recovered to significant level. Thus, our data suggest that exposure to LDR might be a useful antioxidant mediator to suppress the Fe-NTA induced-oxidative damage in rats

Protective Effect of Low Dose Gamma Irradiation against Oxidative Damage in Rats Administrated with Ferric- Nitrilotriacetate

International Nuclear Information System (INIS)

Mansonr, S.Z.

2008-01-01

Many studies have demonstrated the beneficial adaptive response of low dose gamma-irradiation. Low dose gamma-irradiation (LDR) might be effective for the prevention of various reactive oxygen species-related diseases. Ferric nitrilotriacetate (Fe-NTA) is a strong oxidant, which generates highly reactive hydroxyl radical and causes injuries of various organs including the kidney and liver. This study was designed to investigate the ability of low dose gamma-irradiation to restrain Fe-NT A induced oxidative stress. Sprague Dawley male albino rats were subjected to low dose gamma-irradiation (50 cGy). Animals were challenged with Fe-NT A (9 mg Fe/kg body weight, intraperitoneally). Results showed that Fe-NTA enhances lipid peroxidation (LPx) accompanied with reduction in glutathione (GSH) content, antioxidant enzymes, viz., glutathione peroxidase (GPX), glutathione reductase (GR), superoxide dismutase (SOD), catalase (CAT) and phase-U metabolizing enzyme glutathione-S-transferase (GST). Fe-NTA also enhances the concentration of blood urea nitrogen (BUN) and serum creatinine as well as alanine aminotransferase (ALT), aspartate aminotransferase (AST) and gamma-glutamyl transpeptidase (GGT) activities. Exposure to low dose gamma- irradiation (3 h after Fe-NTA administration) resulted in a significant decrease in LPx, BUN, serum creatinine contents as well as ALT, AST and GGT enzyme activities. GSH content; GST and antioxidant enzymes were also recovered to significant level. Thus, our data suggest that exposure to LDR might be a useful antioxidant mediator to suppress the Fe-NTA induced-oxidative damage in rats

Modeling of thermo-mechanical and irradiation behavior of mixed oxide fuel for sodium fast reactors

International Nuclear Information System (INIS)

Karahan, Aydin; Buongiorno, Jacopo

2010-01-01

An engineering code to model the irradiation behavior of UO 2 -PuO 2 mixed oxide fuel pins in sodium-cooled fast reactors was developed. The code was named fuel engineering and structural analysis tool (FEAST-OXIDE). FEAST-OXIDE has several modules working in coupled form with an explicit numerical algorithm. These modules describe: (1) fission gas release and swelling, (2) fuel chemistry and restructuring, (3) temperature distribution, (4) fuel-clad chemical interaction and (5) fuel-clad mechanical analysis. Given the fuel pin geometry, composition and irradiation history, FEAST-OXIDE can analyze fuel and cladding thermo-mechanical behavior at both steady-state and design-basis transient scenarios. The code was written in FORTRAN-90 program language. The mechanical analysis module implements the LIFE algorithm. Fission gas release and swelling behavior is described by the OGRES and NEFIG models. However, the original OGRES model has been extended to include the effects of joint oxide gain (JOG) formation on fission gas release and swelling. A detailed fuel chemistry model has been included to describe the cesium radial migration and JOG formation, oxygen and plutonium radial distribution and the axial migration of cesium. The fuel restructuring model includes the effects of as-fabricated porosity migration, irradiation-induced fuel densification, grain growth, hot pressing and fuel cracking and relocation. Finally, a kinetics model is included to predict the clad wastage formation. FEAST-OXIDE predictions have been compared to the available FFTF, EBR-II and JOYO databases, as well as the LIFE-4 code predictions. The agreement was found to be satisfactory for steady-state and slow-ramp over-power accidents.

Modeling of thermo-mechanical and irradiation behavior of mixed oxide fuel for sodium fast reactors

Energy Technology Data Exchange (ETDEWEB)

Karahan, Aydin, E-mail: karahan@mit.ed [Center for Advanced Nuclear Energy Systems, Nuclear Science and Engineering Department, Massachusetts Institute of Technology, MA (United States); Buongiorno, Jacopo [Center for Advanced Nuclear Energy Systems, Nuclear Science and Engineering Department, Massachusetts Institute of Technology, MA (United States)

2010-01-31

An engineering code to model the irradiation behavior of UO{sub 2}-PuO{sub 2} mixed oxide fuel pins in sodium-cooled fast reactors was developed. The code was named fuel engineering and structural analysis tool (FEAST-OXIDE). FEAST-OXIDE has several modules working in coupled form with an explicit numerical algorithm. These modules describe: (1) fission gas release and swelling, (2) fuel chemistry and restructuring, (3) temperature distribution, (4) fuel-clad chemical interaction and (5) fuel-clad mechanical analysis. Given the fuel pin geometry, composition and irradiation history, FEAST-OXIDE can analyze fuel and cladding thermo-mechanical behavior at both steady-state and design-basis transient scenarios. The code was written in FORTRAN-90 program language. The mechanical analysis module implements the LIFE algorithm. Fission gas release and swelling behavior is described by the OGRES and NEFIG models. However, the original OGRES model has been extended to include the effects of joint oxide gain (JOG) formation on fission gas release and swelling. A detailed fuel chemistry model has been included to describe the cesium radial migration and JOG formation, oxygen and plutonium radial distribution and the axial migration of cesium. The fuel restructuring model includes the effects of as-fabricated porosity migration, irradiation-induced fuel densification, grain growth, hot pressing and fuel cracking and relocation. Finally, a kinetics model is included to predict the clad wastage formation. FEAST-OXIDE predictions have been compared to the available FFTF, EBR-II and JOYO databases, as well as the LIFE-4 code predictions. The agreement was found to be satisfactory for steady-state and slow-ramp over-power accidents.

NMR spectroscopy of organic compounds of selenium and tellurium. Communication 8. Constants of spin-spin interaction of /sup 125/Te-/sup 1/o/sup 3/C in nmr spectra of unsaturated organtellurides

Energy Technology Data Exchange (ETDEWEB)

Kalabin, G.A.; Kushnarev, D.F.; Valeev, R.B. (Irkutskij Gosudarstvennyj Univ. (USSR))

1981-06-01

On the basis of /sup 13/C NMR spectra of a series of unsaturated and aromatic tellurium compounds the constants of spin-spin interaction (SSIC) (sup(1.2)J(Te, C)) are measured. A reliable linear relation between /sup 1/J(Te, C) and s-character of a carbon orbitale forming bond with tellurium is found. Correlation of straight SSIC of carbon with selenium and tellurium in isological compounds is established.

Enhancement of methane gas sensing characteristics of graphene oxide sensor by heat treatment and laser irradiation.

Science.gov (United States)

Assar, Mohammadreza; Karimzadeh, Rouhollah

2016-12-01

The present study uses a rapid, easy and practical method for cost-effective fabrication of a methane gas sensor. The sensor was made by drop-casting a graphene oxide suspension onto an interdigital circuit surface. The electrical conductivity and gas-sensing characteristics of the sensor were determined and then heat treatment and in situ laser irradiation were applied to improve the device conductivity and gas sensitivity. Real-time monitoring of the evolution of the device current as a function of heat treatment time revealed significant changes in the conductance of the graphene oxide sensor. The use of low power laser irradiation enhanced both the electrical conductivity and sensing response of the graphene oxide sensor. Copyright © 2016 Elsevier Inc. All rights reserved.

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

International Nuclear Information System (INIS)

Mal, Joyabrata; Nancharaiah, Yarlagadda V.; Maheshwari, Neeraj; Hullebusch, Eric D. van; Lens, Piet N.L.

2017-01-01

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO 3 2− ) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L −1 d −1 . After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO 3 2− L −1 for 42 d before increasing the influent concentration to 20 mg TeO 3 2− L −1 . Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L −1 ) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

International Nuclear Information System (INIS)

Singh, Hemant Kr.; Avasthi, D.K.; Aggarwal, Shruti

2015-01-01

Highlights: •The objective is to study the effect of swift heavy ion (SHI) irradiation on photoanode of DSSC for better efficiency. •This work presents the effect of SHI irradiation on various Transparent conducting oxides (TCOs). •Effects are studied in terms of conductivity and transmittance of TCOs. •ITO-PET gives best results in comparison to ITO and FTO for DSSC application under SHI irradiation. -- Abstract: Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO 2 :F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In 2 O 3 :Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag +9 ions at fluences ranging from 3.0 × 10 11 ions/cm 2 to 3.0 × 10 13 ions/cm 2 . The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV–Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications

Synthesis and structure of aromatic and heterocyclic compounds of tellurium

International Nuclear Information System (INIS)

Sadekov, I.D.; Maksimenko, A.A.; Rivkin, B.B.

1983-01-01

A new universal method of preparing assymmetric and symmetric diaryl-tellurium chlorides and-dibromides, based on the interaction of diarylditellurides with cations of aryl-diazonium in the presence of copper (2) halogenides is developed. High yields of diaryltellium dihalogenices (60-90 de %), the possibility of the a wide variation of the nature of substituents in both components make this reaction one of the most general methods of preparing assymmetric diaryltellurium dihalogenides. It is advisable to use aryldiazonium boron fluorides instead of halogenides in this reaction

Characterization of tellurium-based films for NO2 detection

International Nuclear Information System (INIS)

Tsiulyanu, D.; Tsiulyanu, A.; Liess, H.-D.; Eisele, I.

2005-01-01

Sensing characteristics of tellurium-based thin films for NO 2 monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO 2 with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO 2 sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms

TEM in situ micropillar compression tests of ion irradiated oxide dispersion strengthened alloy

Energy Technology Data Exchange (ETDEWEB)

Yano, K.H., E-mail: kaylayano@u.boisestate.edu [Boise State University, 1910 University Drive, Boise, ID, 83725 (United States); Swenson, M.J. [Boise State University, 1910 University Drive, Boise, ID, 83725 (United States); Wu, Y. [Boise State University, 1910 University Drive, Boise, ID, 83725 (United States); Center for Advanced Energy Studies, 995 University Blvd, Idaho Falls, ID, 83401 (United States); Wharry, J.P. [Boise State University, 1910 University Drive, Boise, ID, 83725 (United States); Purdue University, 400 Central Drive, West Lafayette, IN 47907 (United States)

2017-01-15

The growing role of charged particle irradiation in the evaluation of nuclear reactor candidate materials requires the development of novel methods to assess mechanical properties in near-surface irradiation damage layers just a few micrometers thick. In situ transmission electron microscopic (TEM) mechanical testing is one such promising method. In this work, microcompression pillars are fabricated from a Fe{sup 2+} ion irradiated bulk specimen of a model Fe-9%Cr oxide dispersion strengthened (ODS) alloy. Yield strengths measured directly from TEM in situ compression tests are within expected values, and are consistent with predictions based on the irradiated microstructure. Measured elastic modulus values, once adjusted for the amount of deformation and deflection in the base material, are also within the expected range. A pillar size effect is only observed in samples with minimum dimension ≤100 nm due to the low inter-obstacle spacing in the as received and irradiated material. TEM in situ micropillar compression tests hold great promise for quantitatively determining mechanical properties of shallow ion-irradiated layers.

Effect of dietary alpha-tocopherol supplementation and gamma-irradiation on alpha-tocopherol retention and lipid oxidation in cooked minced chicken

International Nuclear Information System (INIS)

Galvin, K.; Morrissey, P.A.; Buckley, D.J.

1998-01-01

The effects of dietary alpha-tocopherol supplementation and gamma-irradiation on alpha-tocopherol retention and lipid oxidation in cooked minced chicken during refrigerated storage were studied. Minced breast and thigh meat from broilers fed diets supplemented with 100, 200 or 400 mg alpha-tocopheryl acetate/kg feed was irradiated at 2.5 or 4.0 kGy. Cooked irradiated and unirradiated meat was stored at 4 degrees C for 5 days. alpha-Tocopherol concentrations increased with increasing dietary supplementation. Concentrations decreased during storage, but retention was not affected by irradiation. Lipid stability was determined by measuring the formation of thiobarbituric acid-reacting substances (TBARS) and cholesterol oxidation products (COPs) during storage. TBARS and COPs increased during storage and were reduced by increasing levels of dietary alpha-tocopheryl acetate supplementation. Irradiation accelerated TBARS formation during storage, but this was prevented by supplementation with 200 mg alpha-tocopheryl acetate/kg feed. Irradiation tended to increase COPs during storage, although no consistent effects were observed. In general supplementation with over 400 mg alpha-tocopheryl acetate/kg feed may be required to control cholesterol oxidation in minced chicken. The results suggest that, overall, irradiation had little effect on lipid stability in alpha-tocopherol-supplemented meat following cooking and storage

UVA Irradiation of Dysplastic Keratinocytes: Oxidative Damage versus Antioxidant Defense

Science.gov (United States)

Nechifor, Marina T.; Niculiţe, Cristina M.; Urs, Andreea O.; Regalia, Teodor; Mocanu, Mihaela; Popescu, Alexandra; Manda, Gina; Dinu, Diana; Leabu, Mircea

2012-01-01

UVA affects epidermal cell physiology in a complex manner, but the harmful effects have been studied mainly in terms of DNA damage, mutagenesis and carcinogenesis. We investigated UVA effects on membrane integrity and antioxidant defense of dysplastic keratinocytes after one and two hours of irradiation, both immediately after exposure, and 24 h post-irradiation. To determine the UVA oxidative stress on cell membrane, lipid peroxidation was correlated with changes in fatty acid levels. Membrane permeability and integrity were assessed by propidium iodide staining and lactate dehydrogenase release. The effects on keratinocyte antioxidant protection were investigated in terms of catalase activity and expression. Lipid peroxidation increased in an exposure time-dependent manner. UVA exposure decreased the level of polyunsaturated fatty acids, which gradually returned to its initial value. Lactate dehydrogenase release showed a dramatic loss in membrane integrity after 2 h minimum of exposure. The cell ability to restore membrane permeability was noted at 24 h post-irradiation (for one hour exposure). Catalase activity decreased in an exposure time-dependent manner. UVA-irradiated dysplastic keratinocytes developed mechanisms leading to cell protection and survival, following a non-lethal exposure. The surviving cells gained an increased resistance to apoptosis, suggesting that their pre-malignant status harbors an abnormal ability to control their fate. PMID:23222638

Tellurium adsorption on tungsten and molybdenum field emitters

International Nuclear Information System (INIS)

Collins, R.A.; Kiwanga, C.A.

1977-01-01

Studies of the adsorption of tellurium onto tungsten and molybdenum field emitters are described and the results obtained are compared with those obtained in previous work on the adsorption of silicon and selenium. The adsorption of Te onto W was found to be much more uniform than in the case of Se. Although Te is metallic in many of its properties its adsorptive behavior on field emitters is found to be similar to that of selenium and these adsorptive properties are basically common to all semiconductors. The most evident property of these adsorbates is that the work function and emission current decrease simultaneously at coverages of less than half a monolayer and the work function subsequently increases. (B.D.)

XRD monitoring of α self-irradiation in uranium-americium mixed oxides.

Science.gov (United States)

Horlait, Denis; Lebreton, Florent; Roussel, Pascal; Delahaye, Thibaud

2013-12-16

The structural evolution under (241)Am self-irradiation of U(1-x)Am(x)O(2±δ) transmutation fuels (with x ≤ 0.5) was studied by X-ray diffraction (XRD). Samples first underwent a preliminary heat treatment performed under a reducing atmosphere (Ar/H2(4%)) aiming to recover the previously accumulated structural defects. Over all measurements (carried out over up to a full year and for integrated doses up to 1.5 × 10(18) α-decay events·g(-1)), only fluorite U(1-x)Am(x)O(2±δ) solid solutions were observed. Within a few days after the end of the heat treatment, each of the five studied samples was slowly oxidized as a consequence of their move to air atmosphere, which is evidenced by XRD by an initial sharp decrease of the unit cell parameter. For the compounds with x ≤ 0.15, this oxidation occurred without any phase transitions, but for U0.6Am0.4O(2±δ) and U0.5Am0.5O(2±δ), this process is accompanied by a transition from a first fluorite solid solution to a second oxidized one, as the latter is thermodynamically stable in ambient conditions. In the meantime and after the oxidation process, (241)Am α self-irradiation caused a structural swelling up to ∼0.8 vol %, independently of the sample composition. The kinetic constants of swelling were also determined by regression of experimental data and are, as expected, dependent on x and thus on the dose rate. The normalization of these kinetic constants by sample α-activity, however, leads to very close swelling rates among the samples. Finally, evolutions of microstrain and crystallite size were also monitored, but for the considered dose rates and cumulated doses, α self-irradiation was found, within the limits of the diffractometer used, to have almost no impact on these characteristics. Microstrain was found to be influenced instead by the americium content in the materials (i.e., by the impurities associated with americium starting material and the increase of cationic charge heterogeneity with

L-Arginine Increases Cytotoxicity in Irradiated Ehrlich Carcinoma Cell Line: Possible Potential Role of Nitric Oxide

International Nuclear Information System (INIS)

Noaman, E.

2008-01-01

Cancer cells possess nitric oxide syntheses (NOS) which metabolize L-Arginine (L-Arg) for producing nitric oxide (NO) The present study investigates the relations between NO and ionizing radiation in the Ehrlich ascites carcinoma (EAC) cell line. NOS activity was stimulated by exposure of cells to L-Arg just after irradiation. L-Arg (5 m M) supply led to an increase in ionizing radiation induced cytotoxicity (% of viability 18± 3 %) whereas, neither L-Arg itself nor ionizing irradiation caused cell death at the doses used in this study. Also, cells were treated either with L-Thio citrulline (L-Thio), an irreversible inhibitor of NOS or with exogenous superoxide dismutase (SOD) and catalase. L-Thio and SOD prevented L-Arg mediated deleterious effects on Irradiated cells, whereas catalase was ineffective. Intracellular antioxidant enzyme activity was also determined. Ionizing radiation + L-Arg stress altered the activity of catalase (66 % decrease) and glutathione peroxidase (83 % decrease). Our findings demonstrated that L-Arg induces increase the radiation-mediated deleterious effects in Ehrlich ascites carcinoma cells cytotoxicity and that the ratio NO/ O 2 plays a key role in these processes. NO could participate the deleterious effect of irradiation, in conjugation with others reactive oxygen species (ROS) produced during the oxidation of intracellular components by ionizing radiation (dose 6 Gy)

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Singh, Hemant Kr. [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi (India); Avasthi, D.K. [Inter University Accelerator Center, Post Box 10502, New Delhi (India); Aggarwal, Shruti, E-mail: shruti.al@gmail.com [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi (India)

2015-06-15

Highlights: •The objective is to study the effect of swift heavy ion (SHI) irradiation on photoanode of DSSC for better efficiency. •This work presents the effect of SHI irradiation on various Transparent conducting oxides (TCOs). •Effects are studied in terms of conductivity and transmittance of TCOs. •ITO-PET gives best results in comparison to ITO and FTO for DSSC application under SHI irradiation. -- Abstract: Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO{sub 2}:F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In{sub 2}O{sub 3}:Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag{sup +9} ions at fluences ranging from 3.0 × 10{sup 11} ions/cm{sup 2} to 3.0 × 10{sup 13} ions/cm{sup 2}. The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV–Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications.

Prediction model for oxide thickness on aluminum alloy cladding during irradiation

International Nuclear Information System (INIS)

Kim, Yeon Soo; Hofman, G.L.; Hanan, N.A.; Snelgrove, J.L.

2003-01-01

An empirical model predicting the oxide film thickness on aluminum alloy cladding during irradiation has been developed as a function of irradiation time, temperature, heat flux, pH, and coolant flow rate. The existing models in the literature are neither consistent among themselves nor fit the measured data very well. They also lack versatility for various reactor situations such as a pH other than 5, high coolant flow rates, and fuel life longer than ∼1200 hrs. Particularly, they were not intended for use in irradiation situations. The newly developed model is applicable to these in-reactor situations as well as ex-reactor tests, and has a more accurate prediction capability. The new model demonstrated with consistent predictions to the measured data of UMUS and SIMONE fuel tests performed in the HFR, Petten, tests results from the ORR, and IRIS tests from the OSIRIS and to the data from the out-of-pile tests available in the literature as well. (author)

Behavior of high Tc-superconductors and irradiated defects under reactor irradiation

International Nuclear Information System (INIS)

Atobe, Kozo; Honda, Makoto; Fukuoka, Noboru; Yoshida, Hiroyuki.

1991-01-01

It has been well known that the lattice defects of various types are introduced in ceramics without exception, and exert large effect to the function of these materials. Among oxides, the electronic materials positively using oxygen defect control have been already put in practical use. Also in the oxide high temperature superconductors which are Perovskite type composite oxides, the superconductive characteristics are affected largely by the concentration of the oxygen composing them. This is regarded as an important factor for causing superconductivity, related with the oxygen cavities arising at this time and the carriers bearing superconductivity. In this study, the irradiation effect with relatively low dose, the measurement under irradiation, the effect of irradiation temperature, and the effect of radiation quality were evaluated by the irradiation of YBCO, EBCO and LBCO. The experimental method, and the irradiation effect at low temperature and normal temperature, the effect of Co-60 gamma ray irradiation instead of reactor irradiation are reported. (K.I.)

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

Energy Technology Data Exchange (ETDEWEB)

Forootanfar, Hamid [Herbal and Traditional Medicines Research Center, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Amirpour-Rostami, Sahar; Jafari, Mandana [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Forootanfar, Amir [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of); Yousefizadeh, Zahra [The Student Research Committee, Faculty of Pharmacy, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Shakibaie, Mojtaba, E-mail: shakiba@kmu.ac.ir [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of)

2015-04-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K{sub 2}TeO{sub 3}. - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K{sub 2}TeO{sub 3}.

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

International Nuclear Information System (INIS)

Forootanfar, Hamid; Amirpour-Rostami, Sahar; Jafari, Mandana; Forootanfar, Amir; Yousefizadeh, Zahra; Shakibaie, Mojtaba

2015-01-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K 2 TeO 3 . - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K 2 TeO 3

Early life hormetic treatments decrease irradiation-induced oxidative damage, increase longevity, and enhance sexual performance during old age in the Caribbean fruit fly

International Nuclear Information System (INIS)

López-Martínez, Giancarlo; Hahn, Daniel A.

2014-01-01

Early life events can have dramatic consequences on performance later in life. Exposure to stressors at a young age affects development, the rate of aging, risk of disease, and overall lifespan. In spite of this, mild stress exposure early in life can have beneficial effects on performance later in life. These positive effects of mild stress are referred to as physiological conditioning hormesis. In our current study we used anoxia conditioning hormesis as a pretreatment to reduce oxidative stress and improve organismal performance, lifespan, and healthspan of Caribbean fruit flies. We used gamma irradiation to induce mild oxidative damage in a low-dose experiment, and massive oxidative damage in a separate high-dose experiment, in pharate adult fruit flies just prior to adult emergence. Irradiation-induced oxidative stress leads to reduced adult emergence, flight ability, mating performance, and lifespan. We used a hormetic approach, one hour of exposure to anoxia plus irradiation in anoxia, to lower post-irradiation oxidative damage. We have previously shown that this anoxic-conditioning treatment elevates total antioxidant capacity and lowers post-irradiation oxidative damage to lipids and proteins. In this study, conditioned flies had lower mortality rates and longer lifespan compared to those irradiated without hormetic conditioning. As a metric of healthspan, we tracked mating both at a young age (10 d) and old age (30 d). We found that anoxia-conditioned male flies were more competitive at young ages when compared to unconditioned irradiation stressed male flies, and that the positive effects of anoxic conditioning hormesis on mating success were even more pronounced in older males. Our data shows that physiological conditioning hormesis at a young age, not only improves immediate metrics of organismal performance (emergence, flight, mating), but the beneficial effects also carry into old age by reducing late life oxidative damage and improving lifespan and

Solid solutions of gadolinium doped zinc oxide nanorods by combined microwave-ultrasonic irradiation assisted crystallization

Science.gov (United States)

Kiani, Armin; Dastafkan, Kamran; Obeydavi, Ali; Rahimi, Mohammad

2017-12-01

Nanocrystalline solid solutions consisting of un-doped and gadolinium doped zinc oxide nanorods were fabricated by a modified sol-gel process utilizing combined ultrasonic-microwave irradiations. Polyvinylpyrrolidone, diethylene glycol, and triethylenetetramine respectively as capping, structure directing, and complexing agents were used under ultrasound dynamic aging and microwave heating to obtain crystalline nanorods. Crystalline phase monitoring, lattice parameters and variation, morphology and shape, elemental analysis, functional groups, reducibility, and the oxidation state of emerged species were examined by PXRD, FESEM, TEM, EDX, FTIR, micro Raman, H2-TPR, and EPR techniques. Results have verified that irradiation mechanism of gelation and crystallization reduces the reaction time, augments the crystal quality, and formation of hexagonal close pack structure of Wurtzite morphology. Besides, dissolution of gadolinium within host lattice involves lattice deformation, unit cell distortion, and angular position variation. Structure related shape and growth along with compositional purity were observed through microscopic and spectroscopic surveys. Furthermore, TPR and EPR studies elucidated more detailed behavior upon exposure to the exerted irradiations and subsequent air-annealing including the formed oxidation states and electron trapping centers, presence of gadolinium, zinc, and oxygen disarrays and defects, as well as alteration in the host unit cell via gadolinium addition.

A review of the irradiation evolution of dispersed oxide nanoparticles in the b.c.c. Fe-Cr system: Current understanding and future directions

Energy Technology Data Exchange (ETDEWEB)

Wharry, Janelle P., E-mail: jwharry@purdue.edu [Purdue University, 400 Central Drive, West Lafayette, IN 47907 (United States); Swenson, Matthew J.; Yano, Kayla H. [Boise State University, 1910 University Drive, Boise, ID 83725 (United States)

2017-04-01

Thus far, a number of studies have investigated the irradiation evolution of oxide nanoparticles in b.c.c. Fe-Cr based oxide dispersion strengthened (ODS) alloys. But given the inconsistent experimental conditions, results have been widely variable and inconclusive. Crystal structure and chemistry changes differ from experiment to experiment, and the total nanoparticle volume fraction has been observed to both increase and decrease. Furthermore, there has not yet been a comprehensive review of the archival literature. In this paper, we summarize the existing studies on nanoparticle irradiation evolution. We note significant observations with respect to oxide nanoparticle crystallinity, composition, size, and number density. We discuss four possible contributing mechanisms for nanoparticle evolution: ballistic dissolution, Ostwald ripening, irradiation-enhanced diffusion, and homogeneous nucleation. Finally, we propose future directions to achieve a more comprehensive understanding of irradiation effects on oxide nanoparticles in ODS alloys.

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

Energy Technology Data Exchange (ETDEWEB)

Mal, Joyabrata, E-mail: joyabrata2006@gmail.com [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Nancharaiah, Yarlagadda V. [Biofouling and Biofilm Processes Section, Water and Steam Chemistry Division, Bhabha Atomic Research Centre, Kalpakkam, 603102, Tamil Nadu (India); Homi Bhabha National Institute, Anushakti Nagar Complex, Mumbai 400094 (India); Maheshwari, Neeraj [CNRS UMR 7338, BMBI University de Technologie Compiegne, 60200 Compiegne (France); Hullebusch, Eric D. van [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Université Paris-Est, Laboratoire Géomatériaux et Environnement (LGE), EA 4508, UPEM, 77454, Marne-la-Vallée (France); Lens, Piet N.L. [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Department of Chemistry and Bioengineering, Tampere University of Technology, P.O-Box 541, Tampere (Finland)

2017-04-05

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO{sub 3}{sup 2−}) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L{sup −1} d{sup −1}. After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO{sub 3}{sup 2−} L{sup −1} for 42 d before increasing the influent concentration to 20 mg TeO{sub 3}{sup 2−} L{sup −1}. Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L{sup −1}) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Surface studies on graphite furnace platforms covered with Pd, Rh and Ir as modifiers in graphite furnace atomic absorption spectrometry of tellurium

Energy Technology Data Exchange (ETDEWEB)

Pedro, Juana [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Stripekis, Jorge [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina); Departamento de Ingeniería Química, Instituto Tecnológico de Buenos Aires, Av. Eduardo Madero 399 (1106), Buenos Aires (Argentina); Bonivardi, Adrian [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Tudino, Mabel, E-mail: tudino@qi.fcen.uba.ar [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina)

2015-05-01

The main objective of this work is the study of correlations between the efficiency of the distribution of the permanent platinum group modifiers Pd, Rh and Ir over the graphite surface with the aim of improving analytical signal of tellurium. Modifier solution was deposited onto the platform and pyrolysed after drying. In the case of Pd, the physical vaporization/deposition technique was also tested. In order to analyze the differences amongst coverings (morphology, topology and distribution), the graphite surfaces were studied with scanning electron microscopy and energy dispersive X-ray microscopy. Micrographs for physical vaporization and pyrolytic deposition of Pd were also analyzed in order to explain the lack of signal obtained for tellurium with the first alternative. Similar micrographs were obtained for pyrolytic deposition of Ir and Rh and then, compared to those of Pd. Ir showed the most homogeneous distribution on the graphite surface and the tallest and sharpest transient. With the aim of improving the analytical signal of tellurium, the correlation between the surface studies and the tellurium transient signal (height, area and shape) is discussed. - Highlights: • Distribution of Rh, Pd and Ir onto graphite furnaces is evaluated by SEM and EDX • Micrographs and spectra showed that surface distribution could influence Te signal. • Ir showed the best signal together with the most homogeneous surface distribution. • Pd-PVD micrographs revealed the absence of graphite and no signal for Te.

Tellurium labeled analogues of the fatty acid hexadecenoic acid for imaging of myocardial tissue

International Nuclear Information System (INIS)

Mills, S.L.

1980-01-01

Non-invasive nuclear diagnostic procedures for the evaluation of acute myocardial infarction and ischemia are currently limited by problems associated with the availablity of radiopharmaceuticals, development of imaging equipment, and inherent characteristics of radionuclides. Myocardial tissue requires high levels of substrates which provide energy for the continuous functioning of this vital organ. Of the major sources of energy, the most utilized source is fatty acids. Tellurium-123m, with excellent gamma imaging characteristics was chosen as the radionuclide. A 16 carbon fatty acid, hexadecenoic acid, was chosen as the carrier molecule. The tellurium-123m fatty acid radiopharmaceuticals were formulated either in a solution of 20 percent ethanol, two percent polysorbate 80, and brought to volume with normal saline or in 12.5 percent human serum ablumin and brought to volume with normal saline. Biodistribution was performed in three animal species: Sprague-Dawley rats (three rats per time frame), Australian white rabbits (three rabbits per time frame), and mongrel dogs (one dog per time frame). Dosimetry calculations were performed to assess the radiation dose

One-step synthesis of high conductivity silver nanoparticle-reduced graphene oxide composite films by electron beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Liu, Gang; Wang, Yujia; Pu, Xianjuan; Jiang, Yong; Cheng, Lingli, E-mail: chenglingli@shu.edu.cn; Jiao, Zheng, E-mail: zjiao@shu.edu.cn

2015-09-15

Graphical abstract: - Highlights: • Both graphene oxide and silver ion were reduced simultaneously by electron beam-based method. • The size of AgNPs can be controlled by changing the irradiation dose of electron beam. • The AgNPs/rGO nanocomposite exhibits much lower sheet resistivity (0.06 Ω m). - Abstract: A rapid, eco-friendly, one-step electron beam (EB)-based method for both the reduction of graphene oxide and loading of Ag nanoparticles (AgNPs) were achieved. Further, the effects of irradiation dose on the morphology of AgNPs and the sheet resistance of Ag nanoparticles/reduced graphene oxide (AgNPs/rGO) were studied. The results reveal that when the irradiation dose increased from 70 kGy to 350 kGy, the size of the AgNPs decreased and became uniformly distributed over the surface of the rGO nanosheets. However the size of the AgNPs increased when the irradiation dose reached 500 kGy. Four-point probe measurement showed that the sheet resistance of the AgNPs/rGO films decreased with decreasing AgNPs size. The lowest sheet resistivity of 0.06 Ω m was obtained in the film corresponding to 350 kGy irradiation dose, which showed a much lower resistivity than the GO film (5.04 × 10{sup 5} Ω m). The formation mechanisms of the as-prepared AgNPs/rGO nanocomposites were proposed. This study provides a fast and eco-friendly EB irradiation induced method to controlling the dimensions of AgNPs/rGO nanocomposites, which can strongly support the mass production of AgNPs/rGO nanocomposites for practical applications.

One-step synthesis of high conductivity silver nanoparticle-reduced graphene oxide composite films by electron beam irradiation

International Nuclear Information System (INIS)

Liu, Gang; Wang, Yujia; Pu, Xianjuan; Jiang, Yong; Cheng, Lingli; Jiao, Zheng

2015-01-01

Graphical abstract: - Highlights: • Both graphene oxide and silver ion were reduced simultaneously by electron beam-based method. • The size of AgNPs can be controlled by changing the irradiation dose of electron beam. • The AgNPs/rGO nanocomposite exhibits much lower sheet resistivity (0.06 Ω m). - Abstract: A rapid, eco-friendly, one-step electron beam (EB)-based method for both the reduction of graphene oxide and loading of Ag nanoparticles (AgNPs) were achieved. Further, the effects of irradiation dose on the morphology of AgNPs and the sheet resistance of Ag nanoparticles/reduced graphene oxide (AgNPs/rGO) were studied. The results reveal that when the irradiation dose increased from 70 kGy to 350 kGy, the size of the AgNPs decreased and became uniformly distributed over the surface of the rGO nanosheets. However the size of the AgNPs increased when the irradiation dose reached 500 kGy. Four-point probe measurement showed that the sheet resistance of the AgNPs/rGO films decreased with decreasing AgNPs size. The lowest sheet resistivity of 0.06 Ω m was obtained in the film corresponding to 350 kGy irradiation dose, which showed a much lower resistivity than the GO film (5.04 × 10 5 Ω m). The formation mechanisms of the as-prepared AgNPs/rGO nanocomposites were proposed. This study provides a fast and eco-friendly EB irradiation induced method to controlling the dimensions of AgNPs/rGO nanocomposites, which can strongly support the mass production of AgNPs/rGO nanocomposites for practical applications

Synchrotron X-ray irradiation effects on the device characteristics and the resistance to hot-carrier damage of MOSFETs with 4 nm thick gate oxides

International Nuclear Information System (INIS)

Tanaka, Yuusuke; Tanabe, Akira; Suzuki, Katsumi

1998-01-01

The effects of synchrotron x-ray irradiation on the device characteristics and hot-carrier resistance of n- and p-channel metal oxide semiconductor field effect transistors (MOSFETs) with 4 nm thick gate oxides are investigated. In p-channel MOSFETs, device characteristics were significantly affected by the x-ray irradiation but completely recovered after annealing, while the device characteristics in n-channel MOSFETs were not noticeably affected by the irradiation. This difference appears to be due to a difference in interface-state generation. In p-channel MOSFETs, defects caused by boron-ion penetration through the gate oxides may be sensitive to x-ray irradiation, causing the generation of many interface states. These interface states are completely eliminated after annealing in hydrogen gas. The effects of irradiation on the resistance to hot-carrier degradation in annealed 4 nm thick gate-oxide MOSFETs were negligible even at an x-ray dose of 6,000 mJ/cm 2

Tellurium quantum dots: Preparation and optical properties

Science.gov (United States)

Lu, Chaoyu; Li, Xueming; Tang, Libin; Lai, Sin Ki; Rogée, Lukas; Teng, Kar Seng; Qian, Fuli; Zhou, Liangliang; Lau, Shu Ping

2017-08-01

Herein, we report an effective and simple method for producing Tellurium Quantum dots (TeQDs), zero-dimensional nanomaterials with great prospects for biomedical applications. Their preparation is based on the ultrasonic exfoliation of Te powder dispersed in 1-methyl-2-pyrrolidone. Sonication causes the van der Waals forces between the structural hexagons of Te to break so that the relatively coarse powder breaks down into nanoscale particles. The TeQDs have an average size of about 4 nm. UV-Vis absorption spectra of the TeQDs showed an absorption peak at 288 nm. Photoluminescence excitation (PLE) and photoluminescence (PL) are used to study the optical properties of TeQDs. Both the PLE and PL peaks revealed a linear relationship against the emission and excitation energies, respectively. TeQDs have important potential applications in biological imaging and catalysis as well as optoelectronics.

Out-of-pile experiments of fuel-cladding chemical interaction, (2)

International Nuclear Information System (INIS)

Konashi, Kenji; Yato, Tadao; Kaneko, Hiromitsu; Honda, Yutaka

1980-01-01

Cesium seems to be one of the most important fission products in the fuel-cladding chemical interaction of fuel pins for LMFBRs. However the FCCI under irradiation cannot always be explained by considering only cesium-oxygen system as the corrosive, since attack does not occur in the cesium-oxygen system unless oxygen potential is sufficiently high. Cesium-tellurium-oxygen system has been proposed to account for heavy cladding attack which was sometimes found in hypostoichiometric mixed oxide fuel pins. In this paper, the experiment on the reaction of liquid tellurium with stainless steel is reported. The type 316 stainless steel claddings for Monju type fuel pins were used as the test specimens. Tellurium was contained into the cladding tubes with end plugs. The temperature dependence of the attack by tellurium was examined in the range from 450 to 900 deg C for 30 min, and the heating time dependence was examined from 5 min to 200 hr at 725 deg C. An infrared lamp furnace was used for the experiment within 7 hr, and a resistance furnace for longer experiment. The character of corrosion was matrix attack, and the reaction products on the stainless steel surfaces consisted of chrome rich inner phase and iron and nickel rich outer phase. The results are reported. (Kako, I.)

Continuous reduction of tellurite to recoverable tellurium nanoparticles using an upflow anaerobic sludge bed (UASB) reactor.

Science.gov (United States)

Ramos-Ruiz, Adriana; Sesma-Martin, Juan; Sierra-Alvarez, Reyes; Field, Jim A

2017-01-01

According to the U.S. Department of Energy and the European Union, tellurium is a critical element needed for energy and defense technology. Thus methods are needed to recover tellurium from waste streams. The objectives of this study was to determine the feasibility of utilizing upflow anaerobic sludge bed (UASB) reactors to convert toxic tellurite (Te IV ) oxyanions to non-toxic insoluble elemental tellurium (Te 0 ) nanoparticles (NP) that are amendable to separation from aqueous effluents. The reactors were supplied with ethanol as the electron donating substrate to promote the biological reduction of Te IV . One reactor was additionally amended with the redox mediating flavonoid compound, riboflavin (RF), with the goal of enhancing the bioreduction of Te IV . Its performance was compared to a control reactor lacking RF. The continuous formation of Te 0 NPs using the UASB reactors was found to be feasible and remarkably improved by the addition of RF. The presence of this flavonoid was previously shown to enhance the conversion rate of Te IV by approximately 11-fold. In this study, we demonstrated that this was associated with the added benefit of reducing the toxic impact of Te IV towards the methanogenic consortium in the UASB and thus enabled a 4.7-fold higher conversion rate of the chemical oxygen demand. Taken as a whole, this work demonstrates the potential of a methanogenic granular sludge to be applied as a bioreactor technology producing recoverable Te 0 NPs in a continuous fashion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electron microscope study of irradiated beryllium oxide; Etude au microscope electronique de l'oxyde de beryllium irradie

Energy Technology Data Exchange (ETDEWEB)

Bisson, A A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-06-01

The beryllium oxide is studied first by fractography, before and after irradiation, using sintered samples. The fractures are examined under different aspects. The higher density sintered samples, with transgranular fractures are the most interesting for a microscopic study. It is possible to mark the difference between the 'pores' left by the sintering process and the 'bubbles' of gases that can be produced by former thermal treatments. After irradiation, the grain boundaries are very much weakened. By annealing, it is possible to observe the evolution of the gases produced by the reaction (n, 2n) and (n. {alpha}) and gathered on the grain boundaries. The irradiated beryllium oxide is afterwards studied by transmission. For that, a simple method has been used: little chips of the crushed material are examined. Clusters of point defects produced by neutrons are thus detected in crystals irradiated at the three following doses: 6 x 10{sup 19}, 9 x 10{sup 19} and 2 x 10{sup 20} n{sub f} cm{sup -2} at a temperature below 100 deg. C. For the irradiation at 6 x 10{sup 19} n{sub f} cm{sup -2}, the defects are merely visible, but at 2 x l0{sup 20} n{sub f} cm{sup -2} the crystals an crowded with clusters and the Kikuchi lines have disappeared from the micro-diffraction diagrams. The evolution of the clusters into dislocation loops is studied by a series of annealings. The activation energy (0,37 eV) calculated from the annealing curves suggests that it must be interstitials that condense into dislocation loops. Samples irradiated at high temperatures (650, 900 and 1100 deg. C) are also studied. In those specimens the size of the loops is not the same as the equilibrium size obtained after out of pile annealing at the same temperature. Those former loops are more specifically studied and their Burgers vector is determined by micro-diffraction. (author) [French] L'oxyde de beryllium est d'abord etudie, par une methode fractographique, avant et apres irradiation, en

Effect of Artocarpus communis Extract on UVB Irradiation-Induced Oxidative Stress and Inflammation in Hairless Mice

Directory of Open Access Journals (Sweden)

Feng-Lin Yen

2013-02-01

Full Text Available Administration of antioxidants and anti-inflammatory agents is an effective strategy for preventing ultraviolet (UV irradiation-induced skin damage. Artocarpus communis possesses several pharmacological activities, such as antioxidant, anticancer and anti-inflammation. However, the photoprotective activity of methanol extract of A. communis heartwood (ACM in ultraviolet irradiation-induced skin damage has not yet been investigated. The present study was performed using ultraviolet absorption, histopathological observation, antioxidant and anti-inflammation assays to elucidate the mechanism of the photoprotective activity of ACM. Our results indicated that ACM displayed a UVA and UVB absorption effect and then effectively decreased scaly skin, epidermis thickness and sunburn cells during ultraviolet irradiation in hairless mice. ACM not only decreased ultraviolet irradiation-mediated oxidative stress, including lowering the overproduction of reactive oxygen species and lipid peroxidation (p < 0.05, but also reduced the levels of pro-inflammatory cytokines, including tumor necrosis factor-α (TNF-α and interleukin 1β. Additionally, ACM can decrease the synthesis of cytosolic phospholipase A2, cyclooxygenase, inducible nitric oxide synthase and vascular cell adhesion molecular-1 via inhibiting TNF-α-independent pathways (p < 0.05 in UVB-mediated inflammation and formation of sunburn cells. Consequently, we concluded that ACM extract has a photoprotective effect against UVB-induced oxidative stress and inflammation due to its sunscreen property, and its topical formulations may be developed as therapeutic and/or cosmetic products in further studies.

Irradiation effects of the zirconium oxidation and the uranium diffusion in zirconia; Effets d'irradiation sur l'oxydation du zirconium et la diffusion de l'uranium dans la zircone

Energy Technology Data Exchange (ETDEWEB)

Bererd, N

2003-07-01

The context of this study is the direct storage of spent fuel assemblies after operation in reactor. In order to obtain data on the capacities of the can as the uranium diffusion barrier, a fundamental study has been carried out for modelling the internal cladding surface under and without irradiation. The behaviour of zirconium in reactor conditions has at first been studied. A thin uranium target enriched with fissile isotope has been put on a zirconium sample, the set being irradiated by a thermal neutrons flux leading to the fission of the deposited uranium. The energetic history of the formed fission products has revealed two steps: 1)the zirconium oxidation and 2)the diffusion of uranium in the zirconia formed at 480 degrees C. A diffusion coefficient under irradiation has been measured. Its value is 10{sup -15} cm{sup 2}.s{sup -1}. In order to be able to reveal clearly the effect of the irradiation by the fission products on the zirconium oxidation, measurements of thermal oxidation and under {sup 129}Xe irradiation have been carried out. They have shown that the oxidation is strongly accelerated by the irradiation and that the temperature is negligible until 480 degrees C. On the other hand, the thermal diffusion of the uranium in zirconium and in zirconia has been studied by coupling ion implantation and Rutherford backscattering spectroscopy. This study shows that the uranium diffuses in zirconium and is trapped in zirconia in a UO{sub 3} shape. (O.M.)

Aging of magnesium stearate under high doses gamma irradiation and oxidative conditions

Energy Technology Data Exchange (ETDEWEB)

Lebeau, D.; Beuvier, L.; Cornaton, M. [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); Miserque, F. [CEA, DEN, DPC, SCCME, LECA, F-91191 Gif-sur-Yvette (France); Tabarant, M. [CEA, DEN, DPC, SEARS, LISL, F-91191 Gif-sur-Yvette (France); Esnouf, S. [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France); Ferry, M., E-mail: muriel.ferry@cea.fr [CEA, DEN, DPC, SECR, LRMO, F-91191 Gif-sur-Yvette (France)

2015-05-15

Highlights: • Magnesium stearate was radio-oxidized at very high doses using gamma-rays. • H{sub 2} emission was estimated as a function of the integrated dose. • Modifications in the organic solid were followed as a function of the integrated dose. • A non-exhaustive degradation mechanism of magnesium stearate was proposed. - Abstract: In nuclear waste packages conditioning processes, magnesium stearate is widely used because of its high lubricating properties. For safety purposes, the radiolytic degradation of these organic materials has to be better understood to be able to predict their aging in repository conditions. This study reports the radiolytic degradation of magnesium stearate, using gamma-rays at room temperature and under air. Modifications were followed using different analytical tools (XPS, ATR-FTIR, ICP-AES, ATG and mass spectrometry). It has been observed that molecules mainly formed up to 1000 kGy of gamma irradiation dose under radio-oxidation are alkanes, hydroperoxides, double bonds in the aliphatic chain, carboxylates with aliphatic chain shorter than the one of stearate and ketones. At a dose of 4000 kGy, dicarboxylic acids are observed: the formation of these molecules needs a dose of at least 1000 kGy to be created under radio-oxidation. These observations allow us to propose a non-exhaustive degradation mechanism of magnesium stearate under gamma-irradiation at room temperature and under air.

Characterization of tellurium-based films for NO{sub 2} detection

Energy Technology Data Exchange (ETDEWEB)

Tsiulyanu, D. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of)]. E-mail: tsiu@cni.md; Tsiulyanu, A. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of); Liess, H.-D. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany); Eisele, I. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany)

2005-08-01

Sensing characteristics of tellurium-based thin films for NO{sub 2} monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO{sub 2} with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO{sub 2} sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms.

Microwave-irradiation polyol synthesis of PVP-protected Pt–Ni electrocatalysts for methanol oxidation reaction

CSIR Research Space (South Africa)

Mathe, Ntombizodwa R

2017-01-01

Full Text Available ://doi.org/10.1007/s12678-017-0441-3 Microwave-Irradiation Polyol Synthesis of PVP-Protected Pt–Ni Electrocatalysts for Methanol Oxidation Reaction Ntombizodwa R. Mathe Manfred R. Scriba Rirhandzu S. Rikhotso Neil J. Coville ABSTRACT: Bimetallic Pt...

Nitric oxide-mediated bystander signal transduction induced by heavy-ion microbeam irradiation

Science.gov (United States)

Tomita, Masanori; Matsumoto, Hideki; Funayama, Tomoo; Yokota, Yuichiro; Otsuka, Kensuke; Maeda, Munetoshi; Kobayashi, Yasuhiko

2015-07-01

In general, a radiation-induced bystander response is known to be a cellular response induced in non-irradiated cells after receiving bystander signaling factors released from directly irradiated cells within a cell population. Bystander responses induced by high-linear energy transfer (LET) heavy ions at low fluence are an important health problem for astronauts in space. Bystander responses are mediated via physical cell-cell contact, such as gap-junction intercellular communication (GJIC) and/or diffusive factors released into the medium in cell culture conditions. Nitric oxide (NO) is a well-known major initiator/mediator of intercellular signaling within culture medium during bystander responses. In this study, we investigated the NO-mediated bystander signal transduction induced by high-LET argon (Ar)-ion microbeam irradiation of normal human fibroblasts. Foci formation by DNA double-strand break repair proteins was induced in non-irradiated cells, which were co-cultured with those irradiated by high-LET Ar-ion microbeams in the same culture plate. Foci formation was suppressed significantly by pretreatment with an NO scavenger. Furthermore, NO-mediated reproductive cell death was also induced in bystander cells. Phosphorylation of NF-κB and Akt were induced during NO-mediated bystander signaling in the irradiated and bystander cells. However, the activation of these proteins depended on the incubation time after irradiation. The accumulation of cyclooxygenase-2 (COX-2), a downstream target of NO and NF-κB, was observed in the bystander cells 6 h after irradiation but not in the directly irradiated cells. Our findings suggest that Akt- and NF-κB-dependent signaling pathways involving COX-2 play important roles in NO-mediated high-LET heavy-ion-induced bystander responses. In addition, COX-2 may be used as a molecular marker of high-LET heavy-ion-induced bystander cells to distinguish them from directly irradiated cells, although this may depend on the time

Strong nonlinear photonic responses from microbiologically synthesized tellurium nanocomposites

Science.gov (United States)

Liao, K.-S.; Wang, Jingyuan; Dias, S.; Dewald, J.; Alley, N.J.; Baesman, S.M.; Oremland, R.S.; Blau, W.J.; Curran, S.A.

2010-01-01

A new class of nanomaterials, namely microbiologically-formed nanorods composed of elemental tellurium [Te(0)] that forms unusual nanocomposites when combined with poly(m-phenylenevinylene-co-2,5-dioctoxy-phenylenevinylene) (PmPV) is described. These bio-nanocomposites exhibit excellent broadband optical limiting at 532 and 1064 nm. Nonlinear scattering, originating from the laser induced solvent bubbles and microplasmas, is responsible for this nonlinear behavior. The use of bacterially-formed Te(0) when combined with an organic chemical host (e.g., PmPV) is a new green method of nanoparticle syntheses. This opens the possibilities of using unique, biologically synthesized materials to advance future nanoelectronic and nanophotonic applications. ?? 2009 Elsevier B.V. All rights reserved.

Extraction-spectrophotometric method for silicon determination in high-purity substances. 1. Silicon determination in tellurium

Energy Technology Data Exchange (ETDEWEB)

Shaburova, V P; Yudelevich, I G [AN SSSR, Novosibirsk (USSR). Inst. Neorganicheskoj Khimii

1989-01-01

The extraction-spectrophotometric method for silicon determination in tellurium based on extraction isolation of the base by tributyl phosphate from hydrochloride solutions and with addition of HNO/sub 3/ and spectrophotometric silicon determination using malachite green is developed. The method permits to determine 2x10/sup -1/-3x10/sup -4/ % Si.

The use of masking agents in the determination, by hydride generation and atomic-absorption spectrophotometry, of arsenic, antimony, selenium, tellurium, and bismuth in the presence of noble metals

International Nuclear Information System (INIS)

Kellerman, S.P.

1982-01-01

The effectiveness of thiosemicarbazide, tellurium, and potassium iodide as masking agents to eliminate interferences was assessed. Thiosemicarbazide was found to be effective in eliminating or reducing the interferences on arsenic, antimony, and bismuth, and tellurium reduced the interferences on selenium. The interferences on tellurium could not be eliminated. Arsenic, antimony, selenium, and bismuth were determined in metal sulphide concentrates that were spiked with the noble metals (defined here as gold plus all the platinum-group metals except osmium). The relative standard deviations for arsenic, antimony, bismuth, and selenium were 0,061, 0,017, 0,029, and 0,145 respectively. The values obtained for all the analytes agreed favourably with the preferred values for two in-house reference samples. The laboratory method is detailed in an appendix

Using of Coffee and Cardamom Mixture to Ameliorate Oxidative Stress Induced in irradiated Rats

International Nuclear Information System (INIS)

Hamza, R.G.; Osman, N.N.

2013-01-01

Human exposure to ionizing radiation induced overproduction of free radicals leading to oxidative stress. This study aimed to evaluate the possibility of using of coffee and cardamom mixture; as natural antioxidant compounds ; to ameliorate oxidative stress in rats induced by exposure to ionizing radiation. Phenolic contents in coffee and essential oils in cardamom were identified by using HPLC chromatography and GC/MS analysis. Four groups of adult male rats were used; the control group (A), the second group (B) received orally the mixture extract of coffee and cardamom (60 mg/100g body weight) for 8 weeks, the third group (C) irradiated (6 Gy) and the fourth group (D) received orally the mixture extract for 8 weeks and exposed to radiation at the 4th week. The results revealed that the administration of mixture extract of coffee and cardamom to rats significantly reduced the damage effect induced by irradiation via the adjustment of the antioxidant status, decreasing of malondialdehyde content and the subsequent amending of different biochemical parameters as well as some hormones. Accordingly, it is possible to indicate that coffee-cardamom reduced the radiation exposure induced oxidative stress.

Shark Cartilage Attenuates Oxidative Stress in the liver of Guinea Pigs Exposed to Carbon Tetrachloride and/or Gamma Irradiation

International Nuclear Information System (INIS)

Ibrahim, N.K.; Abd El Aziz, N.

2009-01-01

There is overwhelming evidence to indicate that oxidative stress is involved in the pathogenesis of several diseases. Carbon tetrachloride (CCl 4 ) and ionizing radiations are environmental pollutants well known to induce free radicals formation and oxidative stress. The objective of this work was to evaluate the effect of shark cartilage administration on CCl 4 and/or gamma radiation-induced oxidative damage in the liver. CCl 4 (1 ml/kg body wt) was subcutaneously administered to guinea pigs twice a week for four weeks. Gamma irradiation (RAD) was applied by whole body exposure of guinea pigs to 1.0 Gy/week up to a total dose of 4.0 Gy. Shark cartilage (ShC) was given to animals at a concentration of 1.0 g/kg body wt daily, one week before exposure to CCl 4 and/or gamma irradiation and during the experimental period. Animals sacrificed at the end of the experimental period showed that administration of shark cartilage has significantly attenuated the increase in liver malonaldehyde (MDA) observed in CCl 4 and/or irradiated guinea pigs. Furthermore, shark cartilage treatment has significantly increased the activity of antioxidant enzymes: superoxide dismutase (SOD) and catalase (CAT) and the content of reduced glutathione (GSH). The amelioration of oxidative stress induced in liver tissues of CCL 4 and/or irradiated guinea pigs treated with shark cartilage was associated with significant improvement in the activity of serum alanine amino transferase (ALT), aspartate amino transferase (AST), alkaline phosphatase (ALP), as well as, bilirubin, albumin, and iron contents. It could be concluded that shark cartilage might protect liver tissues from oxidative injury induced by environmental pro-oxidants pollutants via modulating the antioxidant status and decreasing the process of lipid peroxidation

High performance supercapacitor and non-enzymatic hydrogen peroxide sensor based on tellurium nanoparticles

Directory of Open Access Journals (Sweden)

M. Manikandan

2017-04-01

Full Text Available Tellurium nanoparticles (Te Nps were synthesized by wet chemical method and characterized by XRD, Raman, FESEM, TEM, XPS, UV–Vis and FL. The Nps were coated on graphite foil and Glassy carbon electrode to prepare the electrodes for supercapacitor and biosensor applications. The supercapacitor performance is evaluated in 2 M KOH electrolyte by both Cyclic Voltammetry (CV and galvanostatic charge-discharge method. From charge-discharge method, Te Nps show a specific capacitance of 586 F/g at 2 mA/cm2 and 100 F/g at 30 mA/cm2 as well as an excellent cycle life (100% after 1000 cycles. In addition, the H2O2 sensor performance of Te Nps modified glassy carbon electrode is checked by CV and Chronoamperometry (CA in phosphate buffer solution (PBS. In the linear range of 0.67 to 8.04 μM of hydrogen peroxide (H2O2, Te NPs show a high sensitivity of 0.83 mA mM−1 cm−2 with a correlation coefficient of 0.995. The detection limit is 0.3 μM with a response time less than 5 s. Keywords: Tellurium nanoparticles, Supercapacitor, Biosensor, Hydrogen peroxide

Studies on the formation of volatile amines from trimethylamine oxide by gamma-irradiation, (1)

International Nuclear Information System (INIS)

Uchiyama, Sadao; Kondo, Tatsuo; Uchiyama, Mitsuru

1976-01-01

The fundamental investigation concerning the formation of volatile amines from trimethylamine oxide (TMAO) by gamma-irradiation was carried out as a model of the irradiation of fish-meat products like Kamaboko. By the irradiation of 5.8 Mrad, 5 x 10 -6 mol of dimethylamine (DMA) was produced from 1 x 10 -4 mol of TMAO in a phosphate buffer (pH 6.5). Fe 2+ , Fe 3+ , Zn 2+ and Al 3+ promoted the formation of amines but Ca 2+ , Mg 2+ and Na + scarcely affected it. On the other hand, cysteine, which is known as a protecting agent against gamma-ray, promoted the formation of DMA. However, protain worked repressibly for amine formation even when Fe 3+ was contained. (auth.)

Development of ionization effects on oxidative stability of spices and its enhancement in the detection of irradiated foods

International Nuclear Information System (INIS)

Mekni, Mouna

2010-01-01

Physico-chemical properties and anti oxidative stability were released on extracts from untreated (non irradiated) caraway (carum carvi) and oregano leaves (origanum vulgare) samples, as well as from those γ irradiated by Co 6 0 source at doses from 0,5 to 15 kGy were studied by EPR and UV-Vis Spectroscopy, and expressed as DPPH radical scavenging ability, antioxidant index which was determined by β carotene/linoleic acid co-oxidation and total phenolic compounds content (TPC) of each extract were characterized. Respecting the fact that the application of γ radiation on spices leads to the production of paramagnetic species, character of radicals formed upon γ irradiation in solid phase was studied by mean of EPR spectroscopy and the stability of the obtained EPR signal of irradiated samples was studied over a storage period of 3 months. Irradiation was found to nonsignificantly increase and/or maintain all antioxidant parameters, TPC and the EPR signal intensity was found to be increased in studied spices with the radiation doses. The EPR measurements performed during storage period after radiation process showed a significant decrease of free radicals signal intensity until their stability.

DT fusion neutron irradiation of ORNL magnesium oxide crystals and BNL--LASL superconductor wires

International Nuclear Information System (INIS)

MacLean, S.C.

1978-01-01

The DT fusion neutron irradiation of two ORNL magnesium oxide crystals and eleven BNL-LASL superconductor wires is described. The sample position and neutron dose record are given. The maximum neutron fluence on any sample was 2.16 x 10 16 neutrons/cm 2

Structural and optical studies of 100 MeV Au irradiated thin films of tin oxide

Science.gov (United States)

Jaiswal, Manoj Kumar; Kanjilal, D.; Kumar, Rajesh

2013-11-01

Thin films of tin(IV) oxide (SnO2) of 100 nm thickness were grown on silicon (1 0 0) matrices by electron beam evaporation deposition technique under high vacuum. The thicknesses of these films were monitored by piezo-sensor attached to the deposition chamber. Nanocrystallinity is achieved in these thin films by 100 MeV Au8+ using 1 pnA current at normal incidence with ion fluences varying from 1 × 1011 ions/cm2 to 5 × 1013 ions/cm2. Swift Heavy Ion beam irradiation was carried out by using 15 UD Pelletron Accelerator at IUAC, New Delhi, India. Optical studies of pristine and ion irradiated thin films were characterized by UV-Visible spectroscopy and Fourier Transform Infrared (FTIR) spectroscopy. Prominent peak at 610 cm-1 in FTIR spectrum confirmed the O-Sn-O bonding of tin(IV) oxide. For Surface topographical studies and grain size calculations, these films were characterized by Atomic Force Microscope (AFM) using Nanoscope III-A. Crystallinity and phase transformation due to irradiation of pristine and irradiated films were characterized by Glancing Angle X-ray Diffraction (GAXRD) using Brucker-D8 advance model. GAXRD results show improvement in crystallinity and phase transformation due to swift heavy ion irradiation. Grain size distribution was verified by AFM and GAXRD results. Swift heavy ion induced modifications in thin films of SnO2 were confirmed by the presence of prominent peaks at 2θ values of 30.65°, 32.045°, 43.94°, 44.96° and 52.36° in GAXRD spectrum.

Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins

International Nuclear Information System (INIS)

Roake, W.E.; Adamson, M.G.; Hilbert, R.F.; Langer, S.

1977-01-01

Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to ∼60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin

Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins

Energy Technology Data Exchange (ETDEWEB)

Roake, W E [Westinghouse-Hanford Co., Richland, WA (United States); Adamson, M G [General Electric Company, Vallecitos Nuclear Center, Pleasanton, CA (United States); Hilbert, R F; Langer, S

1977-04-01

Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to {approx}60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin

γ-Irradiation assisted synthesis of graphene oxide sheets supported Ag nanoparticles with single crystalline structure and parabolic distribution from interlamellar limitation

Energy Technology Data Exchange (ETDEWEB)

Yue, Yunhao; Zhou, Baoming; Shi, Jie; Chen, Cheng; Li, Nan; Xu, Zhiwei, E-mail: xuzhiwei@tjpu.edu.cn; Liu, Liangsen; Kuang, Liyun; Ma, Meijun; Fu, Hongjun

2017-05-01

Highlights: • Graphene oxide sheets supported Ag nanoparticles composites are successfully prepared via γ-irradiation without surfactant or functional agent. • Ag nanoparticles exhibit single crystalline structure and parabolic distribution on the surface of graphene oxide sheets. • Proposing a view that the growth of intercellular AgNPs can be limited by graphite oxide. - Abstract: This paper reported a method to fabricate graphene oxide sheets supported Ag nanoparticles (AgNPs/GOS) with single crystalline structure and parabolic distribution without surfactant or functional agent. We used imidazole silver nitrate as intercalation precursor into the layers of graphite oxide, and subsequently reduction and growth of interlamellar AgNPs were induced via γ-irradiation. The results illustrated that the synergism of interlamellar limitation of graphite oxide and fragmentation ability of γ-irradiation could prevent coalescent reaction of AgNPs with other oligomeric clusters, and the single crystalline and small-sized (below 13.9 nm) AgNPs were prepared. Moreover, the content and size of AgNPs exhibited parabolic distribution on GOS surface because the graphite oxide exfoliated to GOS from the edge to the central area of layers. In addition, complete exfoliation degree of GOS and large-sized AgNPs were obtained simultaneously under suitable silver ions concentration. Optimized composites exhibited outstanding surface-enhanced Raman scattering properties for crystal violet with enhancement factor of 1.3 × 10{sup 6} and detection limit of 1.0 × 10{sup −7} M, indicating that the AgNPs/GOS composites could be applied to trace detection of organic dyes molecules. Therefore, this study presented a strategy for developing GOS supported nanometal with single crystalline structure and parabolic distribution based on γ-irradiation.

γ-Irradiation assisted synthesis of graphene oxide sheets supported Ag nanoparticles with single crystalline structure and parabolic distribution from interlamellar limitation

International Nuclear Information System (INIS)

Yue, Yunhao; Zhou, Baoming; Shi, Jie; Chen, Cheng; Li, Nan; Xu, Zhiwei; Liu, Liangsen; Kuang, Liyun; Ma, Meijun; Fu, Hongjun

2017-01-01

Highlights: • Graphene oxide sheets supported Ag nanoparticles composites are successfully prepared via γ-irradiation without surfactant or functional agent. • Ag nanoparticles exhibit single crystalline structure and parabolic distribution on the surface of graphene oxide sheets. • Proposing a view that the growth of intercellular AgNPs can be limited by graphite oxide. - Abstract: This paper reported a method to fabricate graphene oxide sheets supported Ag nanoparticles (AgNPs/GOS) with single crystalline structure and parabolic distribution without surfactant or functional agent. We used imidazole silver nitrate as intercalation precursor into the layers of graphite oxide, and subsequently reduction and growth of interlamellar AgNPs were induced via γ-irradiation. The results illustrated that the synergism of interlamellar limitation of graphite oxide and fragmentation ability of γ-irradiation could prevent coalescent reaction of AgNPs with other oligomeric clusters, and the single crystalline and small-sized (below 13.9 nm) AgNPs were prepared. Moreover, the content and size of AgNPs exhibited parabolic distribution on GOS surface because the graphite oxide exfoliated to GOS from the edge to the central area of layers. In addition, complete exfoliation degree of GOS and large-sized AgNPs were obtained simultaneously under suitable silver ions concentration. Optimized composites exhibited outstanding surface-enhanced Raman scattering properties for crystal violet with enhancement factor of 1.3 × 10"6 and detection limit of 1.0 × 10"−"7 M, indicating that the AgNPs/GOS composites could be applied to trace detection of organic dyes molecules. Therefore, this study presented a strategy for developing GOS supported nanometal with single crystalline structure and parabolic distribution based on γ-irradiation.

Intrinsic two-dimensional states on the pristine surface of tellurium

Science.gov (United States)

Li, Pengke; Appelbaum, Ian

2018-05-01

Atomic chains configured in a helical geometry have fascinating properties, including phases hosting localized bound states in their electronic structure. We show how the zero-dimensional state—bound to the edge of a single one-dimensional helical chain of tellurium atoms—evolves into two-dimensional bands on the c -axis surface of the three-dimensional trigonal bulk. We give an effective Hamiltonian description of its dispersion in k space by exploiting confinement to a virtual bilayer, and elaborate on the diminished role of spin-orbit coupling. These intrinsic gap-penetrating surface bands were neglected in the interpretation of seminal experiments, where two-dimensional transport was otherwise attributed to extrinsic accumulation layers.

Separation of effects of oxide-trapped charge and interface-trapped charge on mobility in irradiated power MOSFETs

International Nuclear Information System (INIS)

Zupac, D.; Galloway, K.F.; Khosropour, P.; Anderson, S.R.; Schrimpf, R.D.

1993-01-01

An effective approach to separating the effects of oxide-trapped charge and interface-trapped charge on mobility degradation in irradiated MOSFETs is demonstrated. It is based on analyzing mobility data sets which have different functional relationships between the radiation-induced-oxide-trapped charge and interface-trapped charge. Separation of effects of oxide-trapped charge and interface-trapped charge is possible only if these two trapped charge components are not linearly dependent. A significant contribution of oxide-trapped charge to mobility degradation is demonstrated and quantified

Rapid optical determination of topological insulator nanoplate thickness and oxidation

Directory of Open Access Journals (Sweden)

Fan Yang

2017-01-01

Full Text Available The stability of 2D antimony telluride (Sb2Te3 nanoplates in ambient conditions is elucidated. These materials exhibit an anisotropic oxidation mode, and CVD synthesized samples oxidize at a much faster rate than exfoliated samples investigated in previous studies. Optical measurement techniques are introduced to rapidly measure the oxidation modes and thickness of 2D materials. Auger characterization were conducted to confirm that oxygen replaces tellurium as opposed to antimony under ambient conditions. No surface morphology evolution was detected in AFM before and after exposure to air. These techniques were employed to determine the origin of the thickness dependent color change effect in Sb2Te3. It is concluded that this effect is a combination of refractive index change due to oxidation and Fresnel effects.

The influence of oxidation on space charge formation in gamma-irradiated low-density polyethylene

CERN Document Server

Chen, G; Xie, H K; Banford, H M; Davies, A E

2003-01-01

The research presented in this paper investigates the role of oxidation in the formation of space charge in gamma-irradiated low-density polyethylene after being electrically stressed under dc voltage. Polyethylene plaques both with and without antioxidant were irradiated up to 500 kGy using a sup 6 sup 0 Co gamma source and space charge distributions were measured using the piezoelectric induced pressure wave propagation method. It has been found that a large amount of positive charge evolved adjacent to the cathode in the sample without antioxidant and was clearly associated with oxidation of the surface. The amount of charge formed for a given applied stress increased with the dose absorbed by the material. A model has been proposed to explain the formation of space charge and its profile. The charge decay after the removal of the external applied stress is dominated by a process being controlled by the cathode interfacial stress (charge injection) rather than a conventional RC circuit model. On the other ...

Tellurium Enrichment in Jurassic Coal, Brora, Scotland

Directory of Open Access Journals (Sweden)

Liam Bullock

2017-11-01

Full Text Available Mid-Jurassic pyritic coals exposed at the village of Brora, northern Scotland, UK, contain a marked enrichment of tellurium (Te relative to crustal mean, average world coal compositions and British Isles Carboniferous coals. The Te content of Brora coal pyrite is more than one order of magnitude higher than in sampled pyrite of Carboniferous coals. The Te enrichment coincides with selenium (Se and mercury (Hg enrichment in the rims of pyrite, and Se/Te is much lower than in pyrites of Carboniferous coals. Initial pyrite formation is attributed to early burial (syn-diagenesis, with incorporation of Te, Se, Hg and lead (Pb during later pyrite formation. The source of Te may have been a local hydrothermal system which was responsible for alluvial gold (Au in the region, with some Au in Brora headwaters occurring as tellurides. Anomalous Te is not ubiquitous in coal, but may occur locally, and is detectable by laser ablation inductively coupled plasma-mass spectrometry (LA-ICP-MS.

Chemical states of fission products in irradiated uranium-plutonium mixed oxide fuel

International Nuclear Information System (INIS)

Kurosaki, Ken; Uno, Masayoshi; Yamanaka, Shinsuke

1999-01-01

The chemical states of fission products (FPs) in irradiated uranium-plutonium mixed oxide (MOX) fuel for the light water reactor (LWR) were estimated by thermodynamic equilibrium calculations on system of fuel and FPs by using ChemSage program. A stoichiometric MOX containing 6.1 wt. percent PuO 2 was taken as a loading fuel. The variation of chemical states of FPs was calculated as a function of oxygen potential. Some pieces of information obtained by the calculation were compared with the results of the post-irradiation examination (PIE) of UO 2 fuel. It was confirmed that the multicomponent and multiphase thermodynamic equilibrium calculation between fuel and FPs system was an effective tool for understanding the behavior of FPs in fuel. (author)

Optical study of gamma irradiated sodium metaphosphate glasses containing divalent metal oxide MO (ZnO or CdO

Directory of Open Access Journals (Sweden)

E. Nabhan

Full Text Available Sodium metaphosphate glasses containing divalent metal oxide, ZnO or CdO with composition 50 P2O5 – (50 − x Na2O – x MO (ZnO, or CdO where x = 0, 10, 20 (mol% were prepared by conventional melt method. UV/visible spectroscopy and FTIR spectroscopy are measured before and after exposing to successive gamma irradiation doses (5–80 kGy. The optical absorption spectra results of the samples before irradiation reveal a strong UV absorption band at (∼230 nm which is related to unavoided iron impurities. The effects of gamma irradiation on the optical spectral properties of the various glasses have been compared. From the optical absorption spectral data, the optical band gap is evaluated. The main structural groups and the influence of both divalent metal oxide and gamma irradiation effect on the structural vibrational groups are realized through IR spectroscopy. The FTIR spectra of γ-irradiated samples are characterized by the stability of the number and position for the main characteristic band of phosphate groups. To better understood the structural changes during γ-irradiation, a deconvolution of FTIR spectra in the range 650–1450 cm−1 is made. The FTIR deconvolution results found evidence that, the changes occurring after gamma irradiation have been related to irradiation induced structural defects and compositional changes. Keywords: Sodium metaphosphate glass, UV–visible spectra, IR spectra, Deconvolution, Optical band gap, Gamma ray

Effect of tellurium on viscosity and liquid structure of GaSb melts

Energy Technology Data Exchange (ETDEWEB)

Ji Leilei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China); Geng Haoran [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)], E-mail: mse_genghr@ujn.edu.cn; Sun Chunjing [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Teng Xinying; Liu Yamei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)

2008-04-03

The behavior of GaSb melt with tellurium addition was investigated using viscometer and differential scanning calorimetry (DSC). Normally, the viscosity of all melts measured decreased with the increasing temperature. However, anomalous transition points were observed in the temperature dependence of viscosity for Ga-Sb-Te system. Corresponded with the abnormal points on the viscosity-temperature curves, there were thermal effect peaks on the DSC curves. Furthermore, viscous activation energy and flow units of these melts and their structural features were discussed in this paper.

Prenatal irradiation: nitric oxide and oxidative stress roles in radiation-induced apoptosis of the developing central nervous system

International Nuclear Information System (INIS)

Sanjurjo, Julieta

2001-01-01

Full text: The effects of prenatal irradiation on developing brain should be considered at cellular, structural and functional levels, integrating the information obtained from different sources in an appropriated model to explain the mechanisms involved in neuronal damage. That would permit to make risk estimations and improve radiological protection. Human brain is especially sensitive to ionizing radiation during certain stages of prenatal development. At doses such as those received by Hiroshima and Nagasaki's atomic bomb explosions survivors that were prenatally exposed, the maximum risk was to those exposed between the 8th and 15th weeks of gestation, in coincidence with the highest rate of neuron production and its migration to the brain cortex. The major effect produced on both, brain growth and development, was the augmentation of the Severe Mental Retardation (SMR) incidence. Radiation-induced apoptosis of neuronal progenitors should be considered as one of the factors associated with this pathology, apart from those of migration and synaptogenesis. Apoptosis is an innate and evolutionally conserved process by which the cells provoke the inactivation, disorganisation and degradation of their structural and functional components in a systematic fashion, with the aim of producing its own death. It is also the main cell death mechanism induced by low linear energy transfer (LET) ionizing radiation in developing Central Nervous System (CNS). Radioinduced apoptosis characterization during the different developmental stages, its kinetics and the possible implicated mechanisms (like oxidative injury and nitric oxide) was done using an 'in vitro' system of cortical micro masses (primary cultures of brain cortex cells) from rat embryo brains. Cell cultures were exposed to a single dose of gamma radiation, between 0,2 and 2 Gy, supplied by a Co 60 source (Picker C4M60) at a 70 cm distance with a field area size of 25 cm x 25 cm and at a 0,34 Gy/minute dose rate

Determination of melting point of mixed-oxide fuel irradiated in a fast breeder reactor

International Nuclear Information System (INIS)

Tachibana, Toshimichi

1985-01-01

The melting point of fuel is important to set its in-reactor maximum temperature in fuel design. The fuel melting point measuring methods are broadly the filament method and the capsule sealing method. The only instance of measuring the melting point of irradiated mixed oxide (U, Pu)O 2 fuel by the filament method is by GE in the United States. The capsule sealing method, while the excellent means, is difficult in weld sealing the irradiated fuel in a capsule within the cell. In the fast reactor development program, the remotely operated melting point measuring apparatus in capsule sealing the mixed (U, Pu)O 2 fuel irradiated in the experimental FBR Joyo was set in the cell and the melting point was measured, for the first time in the world. (Mori, K.)

Lasing transition at 1.06 μm emission in Nd3+ -doped borate-based tellurium calcium zinc niobium oxide glasses for high-power solid-state lasers.

Science.gov (United States)

Ravi, O; Prasad, K; Jain, Rajiv; Venkataswamy, M; Chaurasia, Shivanand; Deva Prasad Raju, B

2017-08-01

The spectroscopic properties of Tellurium Calcium Zinc Niobium oxide Borate (TCZNB) glasses of composition (in mol%) 10TeO 2  + 15CaO + 5ZnO + 10 Nb 2 O 5  + (60 - x)B 2 O 3  + Nd 2 O 3 (x = 0.1, 0.5, 1.0 or 1.5 mol%) have been investigated experimentally. The three phenomenological intensity parameters Ω 2 , Ω 4, Ω 6 have been calculated using the Judd-Ofelt theory and in turn radiative properties such as radiative transition probabilities, emission cross-sections, branching ratios and radiative lifetimes have been estimated. The trend found in the JO intensity parameter is Ω 2  > Ω 6  > Ω 4 If Ω 6  > Ω 4 , the glass system is favourable for the laser emission 4 F 3 /2  →  4 I 11 /2 in the infrared (IR) wavelength. The experimental values of branching ratio of 4 F 3 /2  →  4 I 11 /2 transition indicate favourable lasing action with low threshold power. The evaluated total radiative transition probabilities (A T ), stimulated emission cross-section (σ e ) and gain bandwidth parameters (σ e  × Δλ p ) were compared with earlier reports. An energy level analysis has been carried out considering the experimental energy positions of the absorption and emission bands. Copyright © 2016 John Wiley & Sons, Ltd.

Investigation into the potential chemical mechanism of the pro-oxidant activity of carotenoids with liposomes under UV-irradiation

Directory of Open Access Journals (Sweden)

Cvetković Dragan J.

2017-01-01

Full Text Available This study focuses on the behavior of β-carotene and lutein inside multilamellar liposomes under continuous UV-irradiation. The liposomes were obtained by the thin film method and carotenoids (Crts were incorporated by mixing at various concentrations (0.005, 0.0075, 0.02, 0.07 and 0.5 mol %. Liposomes formation and the presence of Crts inside them were confirmed by SEM microscopy and FT-IR spectroscopy, respectively. The antioxidant/pro- -oxidant activity of Crts inside liposomes was determined by the thiobarbituric acid–malondialdehyde (TBA–MDA test. The investigated Crts acted more or less unexpected (as pro-oxidants inside the lipid bilayers, interacting with the UV-produced lipid radicals and simultaneously suffering under the UV-irradiation. Their pro-oxidant activity with liposomes and under UV-irradiation could be explained by the formation of unstable adducts in the reaction with peroxyl radicals, or by Crts-cation radicals formation via the electron transfer mechanism. Such tentatively unexpected behavior of carotenoids should be taken into consideration in further carotenoids-based UV-filters projections in cosmetic formulations for skin protection. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. TR-34012

Improved selectivity for Pb(II) by sulfur, selenium and tellurium analogues of 1,8-anthraquinone-18-crown-5: synthesis, spectroscopy, X-ray crystallography and computational studies.

Science.gov (United States)

Mariappan, Kadarkaraisamy; Alaparthi, Madhubabu; Hoffman, Mariah; Rama, Myriam Alcantar; Balasubramanian, Vinothini; John, Danielle M; Sykes, Andrew G

2015-07-14

We report here a series of heteroatom-substituted macrocycles containing an anthraquinone moiety as a fluorescent signaling unit and a cyclic polyheteroether chain as the receptor. Sulfur, selenium, and tellurium derivatives of 1,8-anthraquinone-18-crown-5 (1) were synthesized by reacting sodium sulfide (Na2S), sodium selenide (Na2Se) and sodium telluride (Na2Te) with 1,8-bis(2-bromoethylethyleneoxy)anthracene-9,10-dione in a 1 : 1 ratio. The optical properties of the new compounds are examined and the sulfur and selenium analogues produce an intense green emission enhancement upon association with Pb(II) in acetonitrile. Selectivity for Pb(II) is markedly improved as compared to the oxygen analogue 1 which was also competitive for Ca(II) ion. UV-Visible and luminescence titrations reveal that 2 and 3 form 1 : 1 complexes with Pb(II), confirmed by single-crystal X-ray studies where Pb(II) is complexed within the macrocycle through coordinate covalent bonds to neighboring carbonyl, ether and heteroether donor atoms. Cyclic voltammetry of 2-8 showed classical, irreversible oxidation potentials for sulfur, selenium and tellurium heteroethers in addition to two one-electron reductions for the anthraquinone carbonyl groups. DFT calculations were also conducted on 1, 2, 3, 6, 6 + Pb(II) and 6 + Mg(II) to determine the trend in energies of the HOMO and the LUMO levels along the series.

Synthesis of Novel E-2-Chlorovinyltellurium Compounds Based on the Stereospecific Anti-addition of Tellurium Tetrachloride to Acetylene

Directory of Open Access Journals (Sweden)

Svetlana V. Amosova

2012-05-01

Full Text Available The reaction of tellurium tetrachloride with acetylene proceeds in a stereospecific anti-addition manner to afford the novel products E-2-chlorovinyltellurium trichloride and E,E-bis(2-chlorovinyltellurium dichloride. Reaction conditions for the selective preparation of each of these products were found. The latter was obtained in 90% yield in CHCl₃ under a pressure of acetylene of 10–15 atm, whereas the former product was formed in up to 72% yield in CCl₄ under a pressure of acetylene of 1–3 atm. Synthesis of the previously unknown E,E-bis(2-chlorovinyl telluride, E,E-bis(2-chlorovinyl ditelluride, E-2-chlorovinyl 1,2,2-trichloroethyl telluride and E,E-bis(2-chlorovinyl-tellurium dibromide is described.

The application of three-phase liquid-liquid extraction to the analysis of bismuth and tellurium in sulphide concentrates

International Nuclear Information System (INIS)

Nicholas, D.J.

1976-01-01

An extraction system consisting of one aqueous and two organic phases is described. Diantipyrylmethane (DAM) is used as the extractant for bismuth and tellurium, which are extracted into the smaller of the two organic phases from nitric acid and perchloric acid respectively. The extraction efficiency is in the range of 90 to 95 per cent, compensation for incomplete extraction being made by the technique of standard addition. Copper, lead, and zinc are not extracted in either procedure. When the solutions contain high concentrations of iron, thioglycolic acid is used as a masking agent for iron in the extraction of bismuth. Atomic-absorption spectrophotometry is used for the analysis of the third phase after it has been diluted with methanol. The precision for bismuth and tellurium is in the range of 3 to 4 per cent. The accuracy, as ascertained from comparative analyses of sulphide concentrates, is good

Characteristics of the behavior of rare-earth oxides and composites on their base by charged particles and neutrons irradiated

International Nuclear Information System (INIS)

Tuseev, T.; Aksenova, T.I.; Berdauletov, A.K.

2000-01-01

In this work the results of comparative investigation of adsorption curves versus REM order number (La, Ce, Nd, Pr, Gd) and dose neutron irradiation are presented. It is discovered that the original REM oxides have high adsorption capacity both for donor gases and for acceptor ones. The adsorption capacity for oxygen and hydrogen becomes lower when the REM order number is higher, but it is contrary for water molecules. The obtained results showed that adsorption properties of REM oxides were changing on identical laws. But oxides of metals, having anomalous properties (variable valency, high cross-section capture) revealed especial adsorption properties under irradiation. In the time of consideration of possible mechanism of radiation - stimulated gas adsorption on oxide surface it is necessary to take in attention both the formation of radiation defects in crystal lattice and the characteristics of electron structure and presence of 4 f - cover in rare-earth metals

Building up Graphene-Based Conductive Polymer Composite Thin Films Using Reduced Graphene Oxide Prepared by γ-Ray Irradiation

Directory of Open Access Journals (Sweden)

Siyuan Xie

2013-01-01

Full Text Available In this paper, reduced graphene oxide (RGO was prepared by means of γ-ray irradiation of graphene oxide (GO in a water/ethanol mix solution, and we investigated the influence of reaction parameters, including ethanol concentration, absorbed dose, and dose rate during the irradiation. Due to the good dispersibility of the RGO in the mix solution, we built up flexible and conductive composite films based on the RGO and polymeric matrix through facile vacuum filtration and polymer coating. The electrical and optical properties of the obtained composite films were tested, showing good electrical conductivity with visible transmittance but strong ultraviolet absorbance.

Investigation of influence of radioactive irradiation on the microstructure of oxide dispersion strengthened steels

International Nuclear Information System (INIS)

Vlasenko, S.V.; Benediktovich, A.I.; Ul'yanenkova, T.A.; O’Konnell, Zh.; Nitling, I.

2015-01-01

The microstructure of unirradiated and irradiated samples of oxide dispersion strengthened (ODS) steels was investigated by X-ray diffraction in order to determine the influence of radiation on mechanical properties of steels. The microstructural parameters of ODS steels from measured diffraction profiles were evaluated using an approach where the complex oxide nanoparticles (Y 2 Ti 2 O 7 and Y 4 Al 2 O 9 ) are modeled as spherical inclusions in the steel matrix with coherent boundaries. The proposed method enables processing of diffraction data from materials containing spherical inclusions by treating them as one more source of peak broadening in addition to straight dislocations, and taking into account broadening due to crystallite size and instrumental effects. The microstructural parameters were obtained on the basis of fitting of experimental data by theoretical curve. The parameters of crystallite size distribution modeled by a lognormal distribution function (the median m and the variance σ), the strain anisotropy parameter q, the dislocation density, the dislocation arrangement parameter M, the density of oxide nanoparticles and the nanoparticle radius r 0 were determined for the ODS steel samples. It was established that irradiation has no significant influence on microstructure. The results obtained for physical parameters are in good agreement with the results of high-resolution transmission electron microscopy (HRTEM). (authors)

Structural and optical studies of 100 MeV Au irradiated thin films of tin oxide

Energy Technology Data Exchange (ETDEWEB)

Jaiswal, Manoj Kumar [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi 110 078 (India); Kanjilal, D. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Kumar, Rajesh, E-mail: rajeshkumaripu@gmail.com [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi 110 078 (India)

2013-11-01

Thin films of tin(IV) oxide (SnO{sub 2}) of 100 nm thickness were grown on silicon (1 0 0) matrices by electron beam evaporation deposition technique under high vacuum. The thicknesses of these films were monitored by piezo-sensor attached to the deposition chamber. Nanocrystallinity is achieved in these thin films by 100 MeV Au{sup 8+} using 1 pnA current at normal incidence with ion fluences varying from 1 × 10{sup 11} ions/cm{sup 2} to 5 × 10{sup 13} ions/cm{sup 2}. Swift Heavy Ion beam irradiation was carried out by using 15 UD Pelletron Accelerator at IUAC, New Delhi, India. Optical studies of pristine and ion irradiated thin films were characterized by UV–Visible spectroscopy and Fourier Transform Infrared (FTIR) spectroscopy. Prominent peak at 610 cm{sup −1} in FTIR spectrum confirmed the O–Sn–O bonding of tin(IV) oxide. For Surface topographical studies and grain size calculations, these films were characterized by Atomic Force Microscope (AFM) using Nanoscope III-A. Crystallinity and phase transformation due to irradiation of pristine and irradiated films were characterized by Glancing Angle X-ray Diffraction (GAXRD) using Brucker-D8 advance model. GAXRD results show improvement in crystallinity and phase transformation due to swift heavy ion irradiation. Grain size distribution was verified by AFM and GAXRD results. Swift heavy ion induced modifications in thin films of SnO{sub 2} were confirmed by the presence of prominent peaks at 2θ values of 30.65°, 32.045°, 43.94°, 44.96° and 52.36° in GAXRD spectrum.

Physical and structural properties of Sm3+ ions doped heavy metal oxide containing lanthanum-boro-telluirte glass

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-05-01

The structural studies of Tellurium oxide substituted by samarium oxide in lathanum-lead-boro-tellurite glass are successfully prepared with physical and optical parameters are determined. Due to the effect of increased number of non-bridging oxygen's in the glass samples few physical parameters are observed to be decreased. For the better structural analysis FTIR was carried out and transformation of BO3 → BO4 is observed. Most effective absorption coefficient OH- group was attained in the present work.

Irradiated accelerated corrosion of stainless steel

International Nuclear Information System (INIS)

Raiman, S.S.; Wang, P.; Was, G.S.

2015-01-01

Type 316L stainless steel was exposed to a simulated PWR environment with in-situ proton irradiation to investigate the effect of simultaneous irradiation and corrosion. To enable these experiments, a dedicated beamline was constructed to transport a 3.2 MeV proton beam from a tandem accelerator, through the sample that also acts as the window between the beamline vacuum and a corrosion cell designed to flow primary water at 320 C. degrees and 13.1 MPa. Experiments were conducted on 316L stainless steel samples which were irradiated for 24 hours in 320 C. degrees water with 3 ppm H 2 , at dose rates of 7*10 -6 dpa/s and 7*10 -7 dpa/s, for 4, 24, and 72 hours. A dual-layer oxide formed on the samples, with an inner layer rich in Cr with Fe and Ni content, and an outer layer of Fe oxides. Samples were characterized with TEM (Transmission Electron Microscopy), EDS, and Raman spectroscopy to determine the effect of irradiation. Irradiated samples were found to have a thinner and more porous inner oxide which was deficient in chromium. The outer oxide was found to have significant hematite content, suggesting that irradiation led to an increase in ECP (Electro-Chemical Potential) at the oxide-solution interface, causing accelerated dissolution of the oxide under irradiation. (authors)

Thermogravimetric studies of the thermo-oxidative stability of irradiated and unirradiated polyethylene

International Nuclear Information System (INIS)

Novakovic, L.; Gal, O.; Markovic, V.; Stannett, V.T.

1985-01-01

In part one of this series the effects of a phenolic, an amine and a thioester antioxidant on the thermo-oxidative stability of irradiated and unirradiated low-density polyethylene was reported. In this paper the effects of combined phenolic and thioester stabilizers are described. Isothermal thermogravimetric analysis was used to study the systems. Pronounced synergism was observed with the induction periods, the time when the initial weight loss begins and the 5% weight loss. At about 50% of each stabilizer increases greater than twofold were observed both with the unirradiated and irradiated polymers. The rate constants for oxygen uptake were decreased. However, the rates of degradation at 5% weight loss fell between the values of the two pure stabilizers with no pronounced synergism in either case. In the absence of oxygen little effect of either antioxidant or their mixtures was observed. The corresponding activation energies were somewhat higher, however, with the irradiated samples containing antioxidants. Dynamic thermogravimetry was used for this study. A kinetic analysis indicated that there were somewhat different modes of degradation at lower- and higher-temperature ranges. (author)

The influence of composition of fluoride electrolytes and conditions of the electrodeposition on some properties of tellurium

International Nuclear Information System (INIS)

Bugelis, V.M.; Kum, G.N.; Abrarov, O.A.; Madumarov, A.; Navalikhin, L.V.; Ajnakulov, Eh.B.

1981-01-01

Effect of electrolytic bath content, cathode current density, illumination and temperature on specific resistance, photosensitivity, structure and chemical purity of plated tellurium coatings is studied. Deposition is realized from moderately acid fluoride electrolytes at the constant temperature with a platinum working electrode. X-ray studies of precipitates obtained are carried out

Charged defects during alpha-irradiation of actinide oxides as revealed by Raman and luminescence spectroscopy

International Nuclear Information System (INIS)

Mohun, R.; Desgranges, L.; Léchelle, J.; Simon, P.; Guimbretière, G.; Canizarès, A.; Duval, F.; Jegou, C.; Magnin, M.; Clavier, N.; Dacheux, N.; Valot, C.; Vauchy, R.

2016-01-01

We have recently evidenced an original Raman signature of alpha irradiation-induced defects in UO 2 . In this study, we aim to determine whether the same signature also exists in different actinide oxides, namely ThO 2 and PuO 2 . Sintered UO 2 and ThO 2 were initially irradiated with 21 MeV He 2+ ions using a cyclotron device and were subjected to an in situ luminescence experiment followed by Raman analysis. In addition, a PuO 2 sample which had accumulated self-irradiation damage due to alpha particles was investigated only by Raman measurement. Results obtained for the initially white ThO 2 showed that a blue color appeared in the irradiated areas as well as luminescence signals during irradiation. However, Raman spectroscopic analysis showed the absence of Raman signature in ThO 2 . In contrast, the irradiated UO 2 and PuO 2 confirmed the presence of the Raman signature but no luminescence peaks were observed. The proposed mechanism involves electronic defects in ThO 2 , while a coupling between electronic defects and phonons is required to explain the Raman spectra for UO 2 and PuO 2 .

The effects of oxide evolution on mechanical properties in proton- and neutron-irradiated Fe-9%Cr ODS steel

Energy Technology Data Exchange (ETDEWEB)

Swenson, M.J., E-mail: matthewswenson1@u.boisestate.edu [Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Dolph, C.K. [Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Wharry, J.P. [Boise State University, 1910 University Drive, Boise, ID 83725 (United States); Purdue University, 400 Central Drive, West Lafayette, IN 47907 (United States)

2016-10-15

The objective of this study is to evaluate the effect of irradiation on the strengthening mechanisms of a model Fe-9%Cr oxide dispersion strengthened steel. The alloy was irradiated with protons or neutrons to a dose of 3 displacements per atoms at 500 °C. Nanoindentation was used to measure strengthening due to irradiation, with neutron irradiation causing a greater increase in yield strength than proton irradiation. The irradiated microstructures were characterized using transmission electron microscopy and atom probe tomography (APT). Cluster analysis reveals solute migration from the Y-Ti-O-rich nanoclusters to the surrounding matrix after both irradiations, though the effect is more pronounced in the neutron-irradiated specimen. Because the dissolved oxygen atoms occupy interstitial sites in the iron matrix, they contribute significantly to solid solution strengthening. The dispersed barrier hardening model relates microstructure evolution to the change in yield strength, but is only accurate if solid solution contributions to strengthening are considered simultaneously.

Evaluated phase diagrams of binary metal-tellurium systems of the D-block transition elements

International Nuclear Information System (INIS)

Chattopadhyay, G.; Bharadwaj, S.R.

1989-01-01

The binary phase diagrams of metal-tellurium systems for twenty seven d-block transition elements have been critically evaluated. Complete phase diagrams are presented for the elements, chromium, manganese, iron, cobalt, nickel, copper, molybdenum, palladium, silver, lanthanum, platinum and gold, whereas, for scandium, titanium, vanadium, yttrium, zirconium, niobium, technitium, ruthenium, rhodium, hafnium, tantalum, tungsten , rhenium, osmium and iridium, the phase diagrams are incomplete and tentative. (author). 20 refs., 27 tabs., 27 figs

Measurement and protection of the oxidative damage induced by heavy-ion irradiation in human glioblastoma cell lines

International Nuclear Information System (INIS)

Moritake, Takashi; Tsuboi, Koji; Nose, Tadao

2003-01-01

The aim of this study is to evaluate the oxidative damage of DNA caused by low or high linear energy transfer (LET) radiation by measuring the level of 8-hydroxydeoxyguanosine (8-OHdG). Relationship between the 8-OHdG level and the LET value was assessed, and the anti-oxidative effect of 3-methyl-1-phenyl-2-pyrazolin-5-one (edaravone) on DNA was evaluated as well. Solution containing salmon sperm DNA at a concentration of 1.0 mg/ml was irradiated with 10 Gy of x-ray or 290 MeV/u carbon beams with an LET range of 20-80 keV/μm. The 8-OHdG level in the DNA solution was measured by high performance liquid chromatography (HPLC) with an electrochemical detector (ECD) after each irradiation. Edaravone was added to the DNA solution in final concentrations from 10 μM to 1 mM and 8-OHdG level was measured by the same method after irradiation. The level of 8-OHdG increased dose-dependently after x-rays irradiation, and it was significantly suppressed by the presence of edaravone. The yield of 8-OHdG decreased as LET value increased, and the protection efficiency by edaravone decreased as LET value increased. (author)

Measurement and protection of the oxidative damage induced by heavy-ion irradiation in human glioblastoma cell lines

Energy Technology Data Exchange (ETDEWEB)

Moritake, Takashi; Tsuboi, Koji; Nose, Tadao [Tsukuba Univ., Ibaraki (Japan). Inst. of Clinical Medicine; Anzai, Kazunori; Ikota, Nobuo; Ando, Koichi; Ozawa, Toshihiko [National Inst. of Radiological Sciences, Chiba (Japan)

2003-04-01

The aim of this study is to evaluate the oxidative damage of DNA caused by low or high linear energy transfer (LET) radiation by measuring the level of 8-hydroxydeoxyguanosine (8-OHdG). Relationship between the 8-OHdG level and the LET value was assessed, and the anti-oxidative effect of 3-methyl-1-phenyl-2-pyrazolin-5-one (edaravone) on DNA was evaluated as well. Solution containing salmon sperm DNA at a concentration of 1.0 mg/ml was irradiated with 10 Gy of x-ray or 290 MeV/u carbon beams with an LET range of 20-80 keV/{mu}m. The 8-OHdG level in the DNA solution was measured by high performance liquid chromatography (HPLC) with an electrochemical detector (ECD) after each irradiation. Edaravone was added to the DNA solution in final concentrations from 10 {mu}M to 1 mM and 8-OHdG level was measured by the same method after irradiation. The level of 8-OHdG increased dose-dependently after x-rays irradiation, and it was significantly suppressed by the presence of edaravone. The yield of 8-OHdG decreased as LET value increased, and the protection efficiency by edaravone decreased as LET value increased. (author)

Investigation of evaporation characteristics of polonium and its lighter homologues selenium and tellurium from liquid Pb-Bi-eutecticum

CERN Document Server

Neuhausen, J; Eichler, B

2004-01-01

The evaporation behaviour of polonium and its lighter homologues selenium and tellurium dissolved in liquid Pb-Bi-eutecticum (LBE) has been studied at various temperatures in the range from 482 K up to 1330 K under Ar/H2 and Ar/H2O-atmospheres using γ-ray spectroscopy. Polonium release in the temperature range of interest for technical applications is slow. Within short term (1h) experiments measurable amounts of polonium are evaporated only at temperatures above 973 K. Long term experiments reveal that a slow evaporation of polonium occurs at temperatures around 873 K resulting in a fractional polonium loss of the melt around 1% per day. Evaporation rates of selenium and tellurium are smaller than those of polonium. The presence of H2O does not enhance the evaporation within the error limits of our experiments. The thermodynamics and possible reaction pathways involved in polonium release from LBE are discussed.

Corrosion of zirconium alloys in nuclear reactors: A model for irradiation induced enhancement by local radiolysis in the porous oxide

Energy Technology Data Exchange (ETDEWEB)

Lemaignan, C; Salot, R [CEA/DRN/DTP, CENG-SECC, Grenoble (France)

1997-02-01

An analysis has been undertaken of the various cases of local enhancement of corrosion rate of zirconium alloys under irradiation. It is observed that in most cases a strong emission of energetic {beta}{sup -} is present leading to a local energy deposition rate higher than the core average. This suggests that the local transient radiolytic oxidizing species produced in the coolant by the {beta}{sup -} particles could contribute to corrosion enhancement, by increasing the local corrosion potential. This process is applicable to the local enhanced corrosion found in front of stainless steels structural parts, due to the contribution of Mn, and in front of Pt inserts or Cu-rich cruds. It explains also the irradiation corrosion enhancement of Cu-Zr alloys. Enhanced corrosion around neutron absorbing material is explained similarly by pair production from conversion of high energy capture photons in the cladding, leading to energetic electrons. The same process was found to be active with other highly ionizing species like {alpha} from Ni-rich alloys and fission products in homogeneous reactors. Due to the changes induced by the irradiation intensity on the concentration of the radiolytic species, the coolant chemistry, that controls the boundary conditions for oxide growth, has to be analyzed with respect to the local value of the energy deposition rate. An analysis has been undertaken which shows that, in a porous media, the water is exposed to a higher intensity than bulk water. This leads to a higher concentration of oxidizing radiolytic species at the root of the cracks of the porous oxide, and increases the corrosion rate under irradiation. This mechanism, deduced from the explanation proposed for localized irradiation enhanced corrosion, can be extended to the whole reactor core, where the general enhancement of Zr alloys corrosion under irradiation could be attributed to the general radiolysis in the porous zirconia. (author). 18 refs, 3 figs, 3 tabs.

Study of the oxidation and of the mechanical behavior of irradiated elastomers: consequences of the electronic irradiation on the electrical cables during the occurring of a pressurized water reactor accident

International Nuclear Information System (INIS)

Corbin, D.

2001-01-01

This thesis contributes to a better understanding and predictions of the consequences of electronic irradiation on the electrical cables when an accident of a pressurized water reactor occurs. We studied the radio-oxidation and the mechanical behaviour of two irradiated elastomers, EPDM (ethylene-propylene-hexadiene 1,4 terpolymer) and hypalon (chloro-sulfonated polyethylene), used respectively as insulating and sheath material of the cable. In the first part, the conditions of exposure to radiation during an accident are presented. They induce a very heterogeneous dose profile in the cable because of the low range of the involved electrons. This situation contrasts with normal operating conditions of the power plant and corresponding qualification tests. In the latter case, the profile is uniform since it is deposited by γ - rays with large ranges. The second part focuses on degradation under presence of oxygen, with typical dose and dose rate conditions for an accident. Thin films of the two elastomers (basic and formulated polymers) are irradiated by electrons and the oxidation products, and their concentrations are determined chemically. The influence, on the kinetics of radio-oxidation, of three parameters typical for the irradiation, the oxygen pressure, the dose rate and the dose is presented there. The effect of antioxidants is studied in the case of EPDM. The third part describes the results concerning the experimental simulation of the dose profile during the accident on thick plates of two formulated elastomers. The evolution of the breaking mechanical properties, as a function of dose and the thickness of the plates, is presented and analysed in correlation with the oxidation profiles. (author)

In vitro biological test of resistance to oxidation: application to identification of irradiated food

International Nuclear Information System (INIS)

Blache, D.; Prost, M.; Raffi, J.

1991-01-01

The test presented here for the identification of ionized food is a direct application of a biological test of resistance to oxidation, put on for an evaluation of antioxidant properties of pharmaceutic molecules and for the study of free radicals in biology. Consequently, the main part of this datum is relative to this biological test. We only point out, when necessary, how we plan to use it for food items. Our aim in this paper is to present a simple biological test (SPIRAL Patent Pending) to measure the total anti oxidative defence status of individuals utilizing some easy to handle cells: circulating cells. In this presentation, we only limited to red blood cells, but any cell could be used after suitable adaptation of the procedure. The first experiments carried out on irradiated foods are promising, even for foodstuffs in liquid state, but we have surely to do a lot of new ones in order to improve the specificity of this test with regard to irradiation and to define with which food it can be used. (9 refs; 15 figs)

Simulation of the chemical state of irradiated oxide fuel; influence of the internal corrosion on the mechanical properties of Zry-4 tubing

International Nuclear Information System (INIS)

Hofmann, P.

1979-03-01

Zircaloy is not compatible with oxide fuel nor with some fission product elements. Therefore, chemical interaction between the irradiated oxide fuel and the Zry cladding material take place, especially at temperatures that can be reached during reactor incidents (ATWS, LOCA). In order to find out which influence the chemical interaction between the fission products and the Zry cladding material have on the mechanical properties of Zry-4 tubing out-of-pile burst experiments and creep rupture tests have been performed at temperatures >=600 0 C with short tube specimens containing simulated fission products. First of all, assessments of the chemical state of irradiated oxide fuel were performed and a method is described for introducing simulated fission product species into fresh oxide fuel for irradiation tests. As the test results of the out-of-pile studies show, only iodine can lead to a low ductility failure of the Zry-tubing at temperatures >=600 0 C. However, the influence of iodine on the deformation behavior of Zry-tubing can be neglected above 850 0 C. (orig.) [de

Effect of Thai banana (Musa AA group) in reducing accumulation of oxidation end products in UVB-irradiated mouse skin.

Science.gov (United States)

Leerach, Nontaphat; Yakaew, Swanya; Phimnuan, Preeyawass; Soimee, Wichuda; Nakyai, Wongnapa; Luangbudnark, Witoo; Viyoch, Jarupa

2017-03-01

Chronic UVB exposure causes skin disorders and cancer through DNA strand breaks and oxidation of numerous functional groups of proteins and lipids in the skin. In this study, we investigated the effects of Thai banana (Musa AA group, "Khai," and Musa ABB group, "Namwa") on the prevention of UVB-induced skin damage when fed to male ICR mice. Mice were orally fed banana (Khai or Namwa) fruit pulps at dose of 1mg/g body weight/day for 12weeks. The shaved backs of the mice were irradiated with UVB for 12weeks. The intensity dose of UVB-exposure was increased from 54mJ/cm 2 /exposure at week 1 to 126mJ/cm 2 /exposure at week 12. A significant increase in skin thickness, lipid peroxidation, protein oxidation end products, and expression of MMP-1 was observed in UVB-irradiated mouse skin. A reduction in the accumulation of oxidation end products was found in the skin of UVB-irradiated mice receiving Khai. This occurred in conjunction with a reduction in MMP-1 expression, inhibition of epidermal thickening, and induction of γ-GCS expression. The dietary intake of Khai prevented skin damage from chronic UVB exposure by increased γ-GCS expression and reduced oxidation end products included carbonyls, malondialdehyde and 4-hydroxynonenal. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

Science.gov (United States)

Singh, Hemant Kr.; Avasthi, D. K.; Aggarwal, Shruti

2015-06-01

Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO2:F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In2O3:Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag+9 ions at fluences ranging from 3.0 × 1011 ions/cm2 to 3.0 × 1013 ions/cm2. The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV-Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications.

Effect of sample preparation methods on photometric determination of the tellurium and cobalt content in the samples of copper concentrates

Directory of Open Access Journals (Sweden)

Viktoriya Butenko

2016-03-01

Full Text Available Methods of determination of cobalt and nickel in copper concentrates currently used in factory laboratories are very labor intensive and time consuming. The limiting stage of the analysis is preliminary chemical sample preparation. Carrying out the decomposition process of industrial samples with concentrated mineral acids in open systems does not allow to improve the metrological characteristics of the methods, for this reason improvement the methods of sample preparation is quite relevant and has a practical interest. The work was dedicated to the determination of the optimal conditions of preliminary chemical preparation of copper concentrate samples for the subsequent determination of cobalt and tellurium in the obtained solution using tellurium-spectrophotometric method. Decomposition of the samples was carried out by acid dissolving in individual mineral acids and their mixtures by heating in an open system as well as by using ultrasonification and microwave radiation in a closed system. In order to select the optimal conditions for the decomposition of the samples in a closed system the phase contact time and ultrasonic generator’s power were varied. Intensification of the processes of decomposition of copper concentrates with nitric acid (1:1, ultrasound and microwave radiation allowed to transfer quantitatively cobalt and tellurium into solution spending 20 and 30 min respectively. This reduced the amount of reactants used and improved the accuracy of determination by running the process in strictly identical conditions.

Reduction of irradiation off-odor and lipid oxidation in ground beef by α-tocopherol addition and the use of a charcoal pack

International Nuclear Information System (INIS)

Sohn, S.H.; Jang, A.; Kim, J.K.; Song, H.P.; Kim, J.H.; Lee, M.; Jo, C.

2009-01-01

A combination of a charcoal pack during irradiation and α-tocopherol addition into ground beef was applied to eliminate an irradiation characteristic off-odor and to retard the lipid oxidation caused by the irradiation process. Ground beef was mixed with 200 ppm α-tocopherol and gamma irradiated with 0, 5, and 10 kGy with or without a charcoal pack present during the irradiation treatment. The pH of the control group was lower than that of α-tocopherol and charcoal pack treatment initially but increased rapidly and showed higher pH at day 7. Addition of α-tocopherol with or without charcoal pack addition showed lower 2-thiobarbituric acid reactive substances values in irradiated ground beef at days 3 and 7 compared to those without addition. The color of ground beef was not significantly affected by the treatment. However, odor preference result showed that 10 kGy-irradiated ground beef with a combination of charcoal pack and α-tocopherol addition had higher scores than the control group regardless of irradiation. Solid-phase microextraction (SPME) gas chromatograph/mass spectrometry (GC/MS) analysis identified various volatile compounds that were created by irradiation of ground beef. These compounds were reduced or eliminated when a charcoal pack was used during the irradiation process. The results of the present study imply that combination of packaging with a charcoal pack during the irradiation process and addition of α-tocopherol into ground beef is a good method to effectively eliminate an irradiation off-odor and retard the lipid oxidation development in ground beef caused by irradiation

Reduction of irradiation off-odor and lipid oxidation in ground beef by {alpha}-tocopherol addition and the use of a charcoal pack

Energy Technology Data Exchange (ETDEWEB)

Sohn, S.H. [Busan Regional Food and Drug Administration, Busan 608-829 (Korea, Republic of); Jang, A. [National Institute of Animal Science, RDA, Suwon 441-706 (Korea, Republic of); Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Kim, J.K. [Cooperative Research, Extension, and Education Service, Northern Marianas College, Saipan, MP 96950 (Korea, Republic of); Song, H.P. [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Kim, J.H. [Cooperative Research, Extension, and Education Service, Northern Marianas College, Saipan, MP 96950 (Korea, Republic of); Lee, M. [Department of Agricultural Biotechnology and Research Institute of Agriculture and Life Sciences, Seoul National University, Seoul 151-921 (Korea, Republic of); Jo, C. [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of)], E-mail: cheorun@cnu.ac.kr

2009-02-15

A combination of a charcoal pack during irradiation and {alpha}-tocopherol addition into ground beef was applied to eliminate an irradiation characteristic off-odor and to retard the lipid oxidation caused by the irradiation process. Ground beef was mixed with 200 ppm {alpha}-tocopherol and gamma irradiated with 0, 5, and 10 kGy with or without a charcoal pack present during the irradiation treatment. The pH of the control group was lower than that of {alpha}-tocopherol and charcoal pack treatment initially but increased rapidly and showed higher pH at day 7. Addition of {alpha}-tocopherol with or without charcoal pack addition showed lower 2-thiobarbituric acid reactive substances values in irradiated ground beef at days 3 and 7 compared to those without addition. The color of ground beef was not significantly affected by the treatment. However, odor preference result showed that 10 kGy-irradiated ground beef with a combination of charcoal pack and {alpha}-tocopherol addition had higher scores than the control group regardless of irradiation. Solid-phase microextraction (SPME) gas chromatograph/mass spectrometry (GC/MS) analysis identified various volatile compounds that were created by irradiation of ground beef. These compounds were reduced or eliminated when a charcoal pack was used during the irradiation process. The results of the present study imply that combination of packaging with a charcoal pack during the irradiation process and addition of {alpha}-tocopherol into ground beef is a good method to effectively eliminate an irradiation off-odor and retard the lipid oxidation development in ground beef caused by irradiation.

Correlation between donating or accepting electron behavior of the adsorbed CO or H_2 and its oxidation over TiO_2 under ultraviolet light irradiation

International Nuclear Information System (INIS)

Peng, Xiaoying; He, Zhoujun; Yang, Kai; Chen, Xun; Wang, Xuxu; Dai, Wenxin; Fu, Xianzhi

2016-01-01

Graphical abstract: Although both H_2 and CO can be thermodynamically oxidized by O_2 over TiO_2 under UV irradiation, only CO was oxidized by O_2 over TiO_2 due to its donating electrons to TiO_2, while H_2 was not oxidized by O_2 under the same condition due to its accepting electrons from TiO_2. - Highlights: • CO could but H_2 could not be oxidized over TiO_2 under UV irradiation. • Electron transfer behaviors of species adsorbed at TiO_2 were characterized by gas sensing testing. • Adsorbed CO donated electrons to TiO_2 but adsorbed H_2 accepted electrons from TiO_2 under UV irradiation. • Photocatalytic oxidation of species over TiO_2 maybe depends on the electron transfer direction between species and TiO_2. - Abstract: Although both H_2 and CO can be thermodynamically oxidized by O_2 over TiO_2 under ultraviolet light (UV) irradiation, it was found that CO not H_2 could be oxidized over an anatase TiO_2 in this work. The chemisorption results of CO and H_2 at TiO_2 surface under UV irradiation, investigated by a gas sensing testing, showed that CO adsorption at TiO_2 would cause the decrease of TiO_2 surface impedance, whereas H_2 adsorption would cause its increase. It is proposed that the CO adsorbed at TiO_2 donate electrons to TiO_2 (as a process of CO pre-oxidation), resulting in its oxidation. In contrast, the H_2 adsorbed at TiO_2 accept electrons from TiO_2 (as a process of H_2 pre-reduction), which makes it difficult to be oxidized. This result indicates that the photocatalytic oxidation of a reactant over TiO_2 not only depends on the formation of the photo-generated carriers and the subsequent activated oxidizing species, but maybe also depends on the electron transfer behavior at the interface of the adsorbed reactant and TiO_2.

Measurement and protection of the oxidative damage induced by high-LET carbon-ion irradiation in salmon sperm DNA solution

International Nuclear Information System (INIS)

Moritake, T.; Nose, T.; Tsuboi, K.; Anzai, K.; Ikota, N.; Ozawa, T.; Ando, K.

2003-01-01

The aims of this study are to quantify the yield of hydroxyl radicals (OH) , and to evaluate the oxidative damage on DNA after high-linear energy transfer (LET) carbon-ion beams and x-rays. For this purpose, the relationship between the radiolytic yield of OH in aqueous solution and 8-hydroxydeoxyguanosine (8-OHdG) level in DNA solution were assessed after radiation. In addition, the anti-oxidative effect of 3-methyl-1-phenyl-2-pyrazonline-5-one (edaravone) on DNA was evaluated. Culture medium containing 200 mM 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) was irradiated with doses of 0 to 20 Gy with an LET of 20 to 90 keV/μm, and the yields of OH were measured using an electron spin resonance (ESR) spectrometer. Salmon sperm DNA solution at a concentration of 1.0 mg/ml was irradiated with 10 Gy of x-rays or 290 MeV/nucleon carbon-ion beams with an LET range of 20-80 keV/μm. 8-OHdG levels in the DNA solution were measured by HPLC with an electrochemical detector (ECD) after each irradiation. Edaravone was added to the DNA solution in final concentrations of 10 μM to 1 mM and 8-OHdG levels were measured by the same method after irradiation. The yield of OH by carbon-ion radiolysis increased in proportion to the absorbed dose over the range of 0 to 20 Gy, and the yield of OH decreased as LET increased logarithmically from 20 to 90 keV/μm. The level of 8-OHdG increased dose-dependently after x-ray irradiation, and it was significantly suppressed by edaravone. Furthermore, the yield of 8-OHdG and the protection efficiency by edaravone decreased as LET value increased. These unique findings provide further understanding of the indirect effect of high-LET radiation, and chemical protection of oxidative damage on DNA is important for clinical application of high-LET radiation

Measurement and protection of the oxidative damage induced by high-LET carbon-ion irradiation in salmon sperm DNA solution

Energy Technology Data Exchange (ETDEWEB)

Moritake, T; Nose, T [University of Tsukuba, (Japan); Tsuboi, K [Institute of Clinical Medical Center, (Japan); Anzai, K; Ikota, N [National Institute of Radiological Sciences, (Japan); Ozawa, T [Redox Regulation Research Group, (Japan); Ando, K [Research Center of Charged Particle Therapy, (Japan). National Institution

2003-07-01

The aims of this study are to quantify the yield of hydroxyl radicals (OH) , and to evaluate the oxidative damage on DNA after high-linear energy transfer (LET) carbon-ion beams and x-rays. For this purpose, the relationship between the radiolytic yield of OH in aqueous solution and 8-hydroxydeoxyguanosine (8-OHdG) level in DNA solution were assessed after radiation. In addition, the anti-oxidative effect of 3-methyl-1-phenyl-2-pyrazonline-5-one (edaravone) on DNA was evaluated. Culture medium containing 200 mM 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) was irradiated with doses of 0 to 20 Gy with an LET of 20 to 90 keV/{mu}m, and the yields of OH were measured using an electron spin resonance (ESR) spectrometer. Salmon sperm DNA solution at a concentration of 1.0 mg/ml was irradiated with 10 Gy of x-rays or 290 MeV/nucleon carbon-ion beams with an LET range of 20-80 keV/{mu}m. 8-OHdG levels in the DNA solution were measured by HPLC with an electrochemical detector (ECD) after each irradiation. Edaravone was added to the DNA solution in final concentrations of 10 {mu}M to 1 mM and 8-OHdG levels were measured by the same method after irradiation. The yield of OH by carbon-ion radiolysis increased in proportion to the absorbed dose over the range of 0 to 20 Gy, and the yield of OH decreased as LET increased logarithmically from 20 to 90 keV/{mu}m. The level of 8-OHdG increased dose-dependently after x-ray irradiation, and it was significantly suppressed by edaravone. Furthermore, the yield of 8-OHdG and the protection efficiency by edaravone decreased as LET value increased. These unique findings provide further understanding of the indirect effect of high-LET radiation, and chemical protection of oxidative damage on DNA is important for clinical application of high-LET radiation.

LIGHT INDUCED TELLURIUM ENRICHMENT ON CDZNTE CRYSTAL SURFACES DETECTED BY RAMAN SPECTROSCOPY

International Nuclear Information System (INIS)

Hawkins, S; Eliel Villa-Aleman, E; Martine Duff, M; Douglas Hunter, D

2007-01-01

Synthetic CdZnTe or 'CZT' crystals can be grown under controlled conditions to produce high quality crystals to be used as room temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro Raman spectroscopy. The growth of Te rich areas on the surface was induced by low powered lasers. The growth was observed versus time with low power Raman scattering and was observed immediately under higher power conditions. The detector response was also measured after induced Te enrichment

Tritium breeding and release-rate kinetics from neutron-irradiated lithium oxide

International Nuclear Information System (INIS)

Quanci, J.F.

1989-01-01

The research encompasses the measurement of the tritium breeding and release-rate kinetics from lithium oxide, a ceramic tritium-breeding material. A thermal extraction apparatus which allows the accurate measurement of the total tritium inventory and release rate from lithium oxide samples under different temperatures, pressures and carrier-gas compositions with an uncertainty not exceeding 3% was developed. The goal of the Lithium Blanket Module program was to determine if advanced computer codes could accurately predict the tritium production in the lithium oxide blanket of a fusion power plant. A fusion blanket module prototype was built and irradiated with a deuterium-tritium fusion-neutron source. The tritium production throughout the module was modeled with the MCNP three dimensional Monte Carlo code and was compared to the assay of the tritium bred in the module. The MCNP code accurately predicted tritium-breeding trends but underestimated the overall tritium breeding by 30%. The release rate of tritium from small grain polycrystalline sintered lithium oxides with a helium carrier gas from 300 to 450 C was found to be controlled by the first order surface desorption of monotritiated water. When small amounts of hydrogen were added to the helium carrier gas, the first order rate constant increased from the isotopic exchange of hydrogen for tritium at the lithium oxide surface occurring in parallel with the first order desorption process. The isotopic-exchange first order rate constant temperature dependence and hydrogen partial pressure dependence were evaluated

Equilibrium evaporation test of lead-bismuth eutectic and of tellurium in lead-bismuth

International Nuclear Information System (INIS)

Ohno, Shuji; Nishimura, Masahiro; Hamada, Hirotsugu; Miyahara, Shinya; Sasa, Toshinobu; Kurata, Yuji

2005-01-01

A series of equilibrium evaporation experiment was performed to acquire the essential and the fundamental knowledge about the transfer behavior of lead-bismuth eutectic (LBE) and impurity tellurium in LBE from liquid to gas phase. The experiments were conducted using the transpiration method in which saturated vapor in an isothermal evaporation pot was transported by inert carrier gas and collected outside of the pot. The size of the used evaporation pot is 8 cm inner diameter and 15 cm length. The weight of the LBE pool in the pot is about 500 g. The investigated temperature range was 450degC to 750degC. From this experiment and discussion using the data in literature, we have obtained several instructive and useful data on the LBE evaporation behavior such as saturated vapor pressure of LBE, vapor concentration of Pb, Bi and Bi 2 in LBE saturated gas phase, and activity coefficient of Pb in the LBE. The LBE vapor pressure equation is represented as the sum of Pb, Bi and Bi 2 vapor in the temperature range between 550degC and 750degC as logP[Pa]=10.2-10100/T[k]. The gas-liquid equilibrium partition coefficient of tellurium in LBE is in the range of 10 to 100, with no remarkable temperature dependency between 450degC and 750degC. This research was founded by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). (author)

Building new discrete supramolecular assemblies through the interaction of iso-tellurazole N-oxides with Lewis acids and bases.

Science.gov (United States)

Ho, Peter C; Jenkins, Hilary A; Britten, James F; Vargas-Baca, Ignacio

2017-10-13

The supramolecular macrocycles spontaneously assembled by iso-tellurazole N-oxides are stable towards Lewis bases as strong as N-heterocyclic carbenes (NHC) but readily react with Lewis acids such as BR 3 (R = Ph, F). The electron acceptor ability of the tellurium atom is greatly enhanced in the resulting O-bonded adducts, which consequently enables binding to a variety of Lewis bases that includes acetonitrile, 4-dimethylaminopyridine, 4,4'-bipyridine, triphenyl phosphine, a N-heterocyclic carbene and a second molecule of iso-tellurazole N-oxide.

Irradiation of inert matrix and mixed oxide fuel in the Halden test reactor

International Nuclear Information System (INIS)

Hellwig, Ch.; Kasemeyer, U.

2001-01-01

In a new type of fuel, called Inert Matrix Fuel (IMF), plutonium is embedded in a U-free matrix. This offers advantages for more efficient plutonium consumption, higher proliferation resistance, and for inert behaviour later in a waste repository. In the fuel type investigated at PSI, plutonium is dissolved in yttrium-stabilized zirconium oxide (YSZ), a highly radiation-resistant cubic phase, with addition of erbium as burnable poison for reactivity control. A first irradiation experiment of YSZ-based IMF is ongoing in the OECD Material Test Reactor in Halden (HBWR), together with MOX fuel (Rig IFA-651.1). The experiment is described herein and results are presented of the first 120 days of irradiation with an average assembly burnup of 47 kWd/cm 3 . The results are compared with neutronic calculations performed before the experiment, and are used to model the fuel behaviour with the PSI-modified TRANSURANUS code. The measured fuel temperatures are within the expected range. An unexpectedly strong densification of the IMF during the first irradiation cycle does not alter the fuel temperatures. An explanation for this behaviour is proposed. The irradiation at higher linear heat rates during forthcoming cycles will deliver information about the fission gas release behaviour of the IMF. (author)

Irradiation of inert matrix and mixed oxide fuel in the Halden test reactor

Energy Technology Data Exchange (ETDEWEB)

Hellwig, Ch.; Kasemeyer, U

2001-03-01

In a new type of fuel, called Inert Matrix Fuel (IMF), plutonium is embedded in a U-free matrix. This offers advantages for more efficient plutonium consumption, higher proliferation resistance, and for inert behaviour later in a waste repository. In the fuel type investigated at PSI, plutonium is dissolved in yttrium-stabilized zirconium oxide (YSZ), a highly radiation-resistant cubic phase, with addition of erbium as burnable poison for reactivity control. A first irradiation experiment of YSZ-based IMF is ongoing in the OECD Material Test Reactor in Halden (HBWR), together with MOX fuel (Rig IFA-651.1). The experiment is described herein and results are presented of the first 120 days of irradiation with an average assembly burnup of 47 kWd/cm{sup 3}. The results are compared with neutronic calculations performed before the experiment, and are used to model the fuel behaviour with the PSI-modified TRANSURANUS code. The measured fuel temperatures are within the expected range. An unexpectedly strong densification of the IMF during the first irradiation cycle does not alter the fuel temperatures. An explanation for this behaviour is proposed. The irradiation at higher linear heat rates during forthcoming cycles will deliver information about the fission gas release behaviour of the IMF. (author)

Oxidative degradation of phenols in sono-Fenton-like systems upon high-frequency ultrasound irradiation

Science.gov (United States)

Aseev, D. G.; Sizykh, M. R.; Batoeva, A. A.

2017-12-01

The kinetics of oxidative degradation of phenol and chlorophenols upon acoustic cavitation in the megahertz range (1.7 MHz) is studied experimentally in model systems, and the involvement of in situ generated reactive oxygen species (ROSs) is demonstrated. The phenols subjected to high frequency ultrasound (HFUS) are ranked in terms of their rate of conversion: 2,4,6-trichlorophenol > 2,4-dichlorophenol 2-chlorophenol > 4-chlorophenol phenol. Oxidative degradation upon HFUS irradiation is most efficient at low concentrations of pollutants, due to the low steady-state concentrations of the in situ generated ROSs. A dramatic increase is observed in the efficiency of oxidation in several sonochemical oxidative systems (HFUS in combination with other chemical oxidative factors). The system with added Fe2+ (a sono-Fenton system) derives its efficiency from hydrogen peroxide generated in situ as a result of the recombination of OH radicals. The S2O8 2-/Fe2+/HFUS system has a synergetic effect on substrate oxidation that is attributed to a radical chain mechanism. In terms of the oxidation rates, degrees of conversion, and specific energy efficiencies of 4-chlorophenol oxidation based on the amount of oxidized substance per unit of expended energy the considered sonochemical oxidative systems form the series HFUS < S2O8 2-/HFUS < S2O8 2-/Fe2+/HFUS.

Point defects and irradiation in oxides: simulations at the atomic scale; Defauts ponctuels et irradiation dans les oxydes: simulation a l'echelle atomique

Energy Technology Data Exchange (ETDEWEB)

Crocombette, J.P

2005-12-15

The studies done by Jean-Paul Crocombette between 1996 and 2005 in the Service de Recherches de Metallurgie Physique of the Direction de l'Energie Nucleaire in Saclay are presented in this Habilitation thesis. These works were part of the material science researches on the ageing, especially under irradiation, of oxides of interest for the nuclear industry. In this context simulation studies at the atomic scale were performed on two elementary components of ageing under irradiation : point defects and displacement cascades ; using two complementary simulation techniques : ab initio electronic structure calculations and empirical potential molecular dynamics. The first part deals with point defects : self defects (vacancies or interstitials) or hetero-atomic dopants. One first recalls the energetics of such defects in oxides, the specific features of defects calculations and the expected accuracy of these calculations. Then one presents the results obtained on uranium dioxide, oxygen in silver and amorphous silica. The second part tackles the modelling of disintegration recoil nuclei in various?displacement cascades created by crystalline matrices for actinide waste disposal. Cascade calculations give access to the amorphization mechanisms under irradiation of these materials. One thus predicts that the amorphization in zircon takes place directly in the tracks whereas in lanthanum zirconate, the amorphization proceeds through the accumulation of point defects. Finally the prospects of these studies are discussed. (author)

Aluminium and Gamma Irradiation Induced Oxidative Damage in Brain Tissue of Male Rats - Protective Role of Ferulic Acid

International Nuclear Information System (INIS)

Mansour, S.Z.; Hanafi, N.; Noaman, E.

2011-01-01

The current study was carried out to investigate the potential role of ferulic acid (FA) against Aluminium chloride (AlCl 3 ), γ- radiation either alone or combination induced oxidative stress in brain tissue of Wistar rats. The period of the experiment was eight weeks. Animals were administrated by aluminium chloride at a dose of 8.5 mg/kg/day and exposed to a single dose (4 Gy) of γ-radiation. FA was administered orally (50 mg/Kg body weight)/day. Histopathological observations and myeloid protein distribution were recorded in brain tissue. Induction of oxidative stress was recorded after all exposures. Brain tissue of AlCl 3 and γ- irradiation treatments either alone or combined revealed many altered changes and myeloid protein distribution. Also a decrease in serotonin concentration was recorded. An increase in Malonaldialdahyde (MDA) and acetylcholinesterase activity and percentage of saturated fatty acids in plasma and brain tissue was recorded. Reduced glutathione (GSH), catalase (CAT), superoxide dismutase (SOD) in blood and brain showed a significant decrease. Treatment of AlCl 3 loaded animals by FA showed simple atrophy as shrunken morphology saw in amyotrophic lateral sclerosis and a decrease in myeloid protein deposition. FA treatment of AlCl 3 loaded or irradiated animals represented a significant increase in serotonin concentration and ameliorated affects on oxidative stress markers, acetylcholinesterase activity and percentage of saturated fatty acids in plasma and brain tissue. In conclusion FA has a role in reducing the oxidative stress of AlCl 3 and γ- irradiation on brain tissue of rats

Photocatalytic oxidation of indoor toluene: Process risk analysis and influence of relative humidity, photocatalysts, and VUV irradiation

International Nuclear Information System (INIS)

Zhao, Weirong; Dai, Jiusong; Liu, Feifei; Bao, Jiaze; Wang, Yan; Yang, Yong; Yang, Yanan; Zhao, Dongye

2012-01-01

Concentrations of 13 gaseous intermediates in photocatalytic oxidation (PCO) of toluene in indoor air were determined in real-time by proton transfer reaction mass spectrometry and desorption intensities of 7 adsorbed intermediates on the surface of photocatalysts were detected by temperature‐programmed desorption‐mass spectrometry. Effects of relative humidity (RH), photocatalysts, and vacuum ultraviolet (VUV) irradiation on the distribution and category of the intermediates and health risk influence index (η) were investigated. RH enhances the formation rate of hydroxide radicals, leading to more intermediates with higher oxidation states in gas phase. N doping promotes the separation of photo-generated electrons and holes and enhances PCO activity accordingly. VUV irradiation results in higher mineralization rate and more intermediates with higher oxidation states and lower toxicity e.g. carboxylic acids. Health risk analysis indicates that higher RH, N doping of TiO 2 , and VUV lead to “greener” intermediates and smaller η. Finally, a conceptual diagram was proposed to exhibit the scenario of η varied with extent of mineralization for various toxicities of inlet pollutants. Highlights: ► 13 volatile intermediates in PCO of toluene were determined in real-time by PTR-MS. ► 7 adsorbed intermediates on surface of photocatalyst were determined by TPD-MS. ► Higher RH, N doping of TiO 2 , and VUV irradiation lead to “greener” intermediates. ► Health risk index relies on extent of mineralization and toxicities of inlet VOCs.

Surface activation of graphene oxide nanosheets by ultraviolet irradiation for highly efficient anti-bacterials

Science.gov (United States)

Veerapandian, Murugan; Zhang, Linghe; Krishnamoorthy, Karthikeyan; Yun, Kyusik

2013-10-01

A comprehensive investigation of anti-bacterial properties of graphene oxide (GO) and ultraviolet (UV) irradiated GO nanosheets was carried out. Microscopic characterization revealed that the GO nanosheet-like structures had wavy features and wrinkles or thin grooves. Fundamental surface chemical states of GO nanosheets (before and after UV irradiation) were investigated using x-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy. Minimum inhibitory concentration (MIC) results revealed that UV irradiated GO nanosheets have more pronounced anti-bacterial behavior than GO nanosheets and standard antibiotic, kanamycin. The MIC of UV irradiated GO nanosheets was 0.125 μg ml-1 for Escherichia coli and Salmonella typhimurium, 0.25 μg ml-1 for Bacillus subtilis and 0.5 μg ml-1 for Enterococcus faecalis, ensuring its potential as an anti-infective agent for controlling the growth of pathogenic bacteria. The minimum bactericidal concentration of normal GO nanosheets was determined to be two-fold higher than its corresponding MIC value, indicating promising bactericidal activity. The mechanism of anti-bacterial action was evaluated by measuring the enzymatic activity of β-d-galactosidase for the hydrolysis of o-nitrophenol-β-d-galactopyranoside.

Surface activation of graphene oxide nanosheets by ultraviolet irradiation for highly efficient anti-bacterials

International Nuclear Information System (INIS)

Veerapandian, Murugan; Zhang, Linghe; Yun, Kyusik; Krishnamoorthy, Karthikeyan

2013-01-01

A comprehensive investigation of anti-bacterial properties of graphene oxide (GO) and ultraviolet (UV) irradiated GO nanosheets was carried out. Microscopic characterization revealed that the GO nanosheet-like structures had wavy features and wrinkles or thin grooves. Fundamental surface chemical states of GO nanosheets (before and after UV irradiation) were investigated using x-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy. Minimum inhibitory concentration (MIC) results revealed that UV irradiated GO nanosheets have more pronounced anti-bacterial behavior than GO nanosheets and standard antibiotic, kanamycin. The MIC of UV irradiated GO nanosheets was 0.125 μg ml −1 for Escherichia coli and Salmonella typhimurium, 0.25 μg ml −1 for Bacillus subtilis and 0.5 μg ml −1 for Enterococcus faecalis, ensuring its potential as an anti-infective agent for controlling the growth of pathogenic bacteria. The minimum bactericidal concentration of normal GO nanosheets was determined to be two-fold higher than its corresponding MIC value, indicating promising bactericidal activity. The mechanism of anti-bacterial action was evaluated by measuring the enzymatic activity of β-d-galactosidase for the hydrolysis of o-nitrophenol-β-d-galactopyranoside. (paper)

Effects of zinc oxide and titanium dioxide nanoparticles on green algae under visible, UVA, and UVB irradiations: no evidence of enhanced algal toxicity under UV pre-irradiation.

Science.gov (United States)

Lee, Woo-Mi; An, Youn-Joo

2013-04-01

Some metal oxide nanoparticles are photoreactive, thus raising concerns regarding phototoxicity. This study evaluated ecotoxic effects of zinc oxide nanoparticles and titanium dioxide nanoparticles to the green algae Pseudokirchneriella subcapitata under visible, UVA, and UVB irradiation conditions. The nanoparticles were prepared in algal test medium, and the test units were pre-irradiated by UV light in a photoreactor. Algal assays were also conducted with visible, UVA or UVB lights only without nanoparticles. Algal growth was found to be inhibited as the nanoparticle concentration increased, and ZnO NPs caused destabilization of the cell membranes. We also noted that the inhibitory effects on the growth of algae were not enhanced under UV pre-irradiation conditions. This phenomenon was attributed to the photocatalytic activities of ZnO NPs and TiO2 NPs in both the visible and UV regions. The toxicity of ZnO NPs was almost entirely the consequence of the dissolved free zinc ions. This study provides us with an improved understanding of toxicity of photoreactive nanoparticles as related to the effects of visible and UV lights. Copyright © 2012 Elsevier Ltd. All rights reserved.

Determination of gold, indium, tellurium and thallium in the same sample digest of geological materials by atomic-absorption spectroscopy and two-step solvent extraction

Science.gov (United States)

Hubert, A.E.; Chao, T.T.

1985-01-01

A rock, soil, or stream-sediment sample is decomposed with hydrofluoric acid, aqua regia, and hydrobromic acid-bromine solution. Gold, thallium, indium and tellurium are separated and concentrated from the sample digest by a two-step MIBK extraction at two concentrations of hydrobromic add. Gold and thallium are first extracted from 0.1M hydrobromic acid medium, then indium and tellurium are extracted from 3M hydrobromic acid in the presence of ascorbic acid to eliminate iron interference. The elements are then determined by flame atomic-absorption spectrophotometry. The two-step solvent extraction can also be used in conjunction with electrothermal atomic-absorption methods to lower the detection limits for all four metals in geological materials. ?? 1985.

Results of the irradiation of mixed UO2 - PuO2 oxide fuel elements

International Nuclear Information System (INIS)

Mikailoff, H.; Mustelier, J.P.; Bloch, J.; Ezran, L.; Hayet, L.

1966-01-01

In order to study the behaviour of fuel elements used for the first charge of the reactor Rapsodie, a first batch of eleven needles was irradiated in the reactor EL3 and then examined. These needles (having a shape very similar lo that of the actual needles to be used) were made up of a stack of sintered mixed-oxide pellets: UO 2 containing about 10 per cent of PuO 2 . The density was 85 to 97 per cent of the theoretical, value. The diametral gap between the oxide and the stainless steel can was between 0,06 and 0,27 mm. The specific powers varied from 1230 to 2700 W/cm 3 and the can temperature was between 450 and 630 C. The maximum burn-up attained was 22000 MW days/tonne. Examination of the needles (metrology, radiography and γ-spectrography) revealed certain macroscopic changes, and the evolution of the fuel was shown by micrographic studies. These observations were used, together with flux measurements results, to calculate the temperature distribution inside the fuel. The volume of the fission gas produced was measured in some of the samples; the results are interpreted taking into account the temperature distribution in the oxide and the burn-up attained. Finally a study was made both of the behaviour of a fuel element whose central part was molten during irradiation, and of the effect of sodium which had penetrated into some of the samples following can rupture. (author) [fr

Kinetics that govern the release of tritium from neutron-irradiated lithium oxide

International Nuclear Information System (INIS)

Bertone, P.C.

1986-01-01

The Lithium Blanket Module (LBM) program being conducted at the Princeton Plasma Physics Laboratory requires that tritium concentrations as low as 0.1 nCi/g, bred in both LBM lithium oxide pellets and gram-size lithium samples, be measured with an uncertainty not exceeding +/-6%. This thesis reports two satisfactory methods of assaying LBM pellets and one satisfactory method of assaying lithium samples. Results of a fundamental kinetic investigation are also reported. The thermally driven release of tritium from neutron-irradiated lithium oxide pellets is studied between the temperatures of 300 and 400 0 C. The observed release clearly obeys first-order kinetics, and the governing activation energy appears to be 28.4 kcal/mole. Finally, a model is presented that may explain the thermally driven release of tritium from a lithium oxide crystal and assemblies thereof. It predicts that under most circumstances the release is controlled by either the diffusion of a tritiated species through the crystal, or by the desorption of tritiated water from it

Some physical properties of irradiated and non-irradiated oxide glasses containing uranium

International Nuclear Information System (INIS)

Simon, V.; Ardelean, I.; Simon, S.; Cozar, O.; Milea, I.; Lupsa, I.; Mih, V.

1995-01-01

The x U O 3 (1-x) [2 P 2 O 5 · Na 2 O] non-irradiated and gamma irradiated glasses (0 3+ , U 4+ and U 5+ ions. The gamma irradiation induces paramagnetic defects around the glass network forming sites occupied by phosphorous atoms. The non-irradiated samples are weak paramagnetic up to x = 0.1. For higher U O 3 concentration (0.1 < x ≤ 0.2) the magnetic measurements indicated a larger number of paramagnetic ions which are magnetically isolated and exhibit a Curie type behaviour. (author) 5 figs., 14 refs

Effects of γ- and x-irradiation upon activity and selectivity of a supported silver catalyst in the oxidation of ethylene and carbon monoxide

International Nuclear Information System (INIS)

Mora Vallejo, R.J.

1975-01-01

Effects of γ and x-radiation on catalytic selectivity of supported silver catalysts for production of ethylene oxide via ethylene oxidation were compared by determination of radio-induced changes in conversion-yield profiles. Influence of photon energy on the kinetics of the irradiation process was studied by determination of conversion-yield profiles, using samples of catalyst exposed to x-rays of different mean photon energy and γ-rays for different cumulative periods of time. The effect of γ-radiation on catalytic activity of the same silver catalysts for carbon monoxide oxidation was analyzed by determination of the reaction kinetics before and after catalyst irradiation

3-Amino-1,2,4-triazole Limits the Oxidative Damage in UVA-Irradiated Dysplastic Keratinocytes

Directory of Open Access Journals (Sweden)

Marina Tamara Nechifor

2017-01-01

Full Text Available Reactive oxygen species (ROS generated by UVA irradiation affect the keratinocyte cell membrane, DNA, and proteins and may cause serious injury to the skin. Treating human dysplastic keratinocytes (DOK with 3-amino-1,2,4-triazole (AMT, a common catalase inhibitor, induced a compensatory mechanism for the hydrogen peroxide detoxification, which included a rise in glutathione peroxidase and glutathione reductase activities. Here, we examined a possible role of AMT in protecting a human DOK cell line against UVA-induced damage. In DOK cells exposed to UVA irradiation, we observed a substantial decrease in antioxidant enzymatic activities, such as catalase, glutathione peroxidase, glutathione reductase, and glutathione-S-transferase and an increase in lipid peroxidation and protein oxidation levels. Treating DOK cells with AMT prior to UVA exposure enhanced the activities of glutathione peroxidase, glutathione reductase, and glutathione-S-transferase, relative to nontreated cells. The enhanced antioxidant activities were correlated with decreased protein oxidation levels. Based on these results, we suggest that AMT may protect dysplastic keratinocytes against the harmful effects of UVA radiation.

Short-term anoxic conditioning hormesis boosts antioxidant defenses, lowers oxidative damage following irradiation and enhances male sexual performance in the Caribbean fruit fly, Anastrepha suspensa

Energy Technology Data Exchange (ETDEWEB)

Lopez-Martinez, Giancarlo; Hahn, Daniel A [Department of Entomology and Nematology, University of Florida, Gainesville, FL (United States)

2013-01-15

Most organisms are repeatedly exposed to oxidative stress from multiple sources throughout their lifetimes, potentially affecting all aspects of organismal performance. Here we test whether exposure to a conditioning bout of anoxia early in adulthood induces a hormetic response that confers resistance to oxidative stress and enhances male sexual performance later in life in the Caribbean fruit fly, Anastrepha suspensa. Anoxic conditioning of adults prior to emergence led to an increase in antioxidant capacity driven by mitochondrial superoxide dismutase and glutathione peroxidase. When exposed to gamma irradiation, a strong oxidative stressor, males that received anoxic conditioning had lower lipid and protein oxidative damage at sexual maturity. Anoxia conditioning led to greater male sexual competitiveness compared with unconditioned males when both were irradiated, although there was no effect of anoxia conditioning on mating competitiveness in unirradiated males. Anoxia also led to higher adult emergence rates and greater flight ability in irradiation-stressed flies while preserving steriity. Thus, hormetic treatments that increased antioxidant enzyme activity also improved male performance after irradiation, suggesting that antioxidant enzymes play an important role in mediating the relationship between oxidative stress and sexual selection. Furthermore, our work has important applied implications for the sterile insect technique (SIT), an environmentally friendly method of insect pest control where males are sterilized by irradiation and deployed in the field to disrupt pest populations via mating. We suggest that hormetic treatments specifically designed to enhance antioxidant activity may produce more sexually competitive sterile males, thus improving the efficacy and economy of SIT programs. (author)

Evaluation of the Content of Antimony, Arsenic, Bismuth, Selenium, Tellurium and Their Inorganic Forms in Commercially Baby Foods.

Science.gov (United States)

Ruiz-de-Cenzano, M; Rochina-Marco, A; Cervera, M L; de la Guardia, M

2017-12-01

Baby foods, from the Spanish market and prepared from meat, fish, vegetables, cereals, legumes, and fruits, were analyzed to obtain the concentration of antimony (Sb), arsenic (As), bismuth (Bi), and tellurium (Te) as toxic elements and selenium (Se) as essential element. An analytical procedure was employed based on atomic fluorescence spectroscopy which allowed to obtain accurate data at low levels of concentration. Values of 14 commercial samples, expressed in nanograms per gram fresh weight, ranged for Sb 0.66-6.9, As 4.5-242, Te 1.35-2.94, Bi 2.18-4.79, and Se 5.4-109. Additionally, speciation studies were performed based on data from a non-chromatographic screening method. It was concluded that tellurium and bismuth were mainly present as inorganic forms and selenium as organic form, and antimony and arsenic species depend on the ingredients of each baby food. Risk assessment considerations were made by comparing dietary intake of the aforementioned elements through the consumption of one baby food portion a day and recommended or tolerable guideline values.

Transient redistribution of intragranular fission gas in irradiated mixed oxide

International Nuclear Information System (INIS)

Hinman, C.A.; Randklev, E.H.

1981-01-01

Safety analyses for an LMFBR require a knowledge of the fuel and fission gas behavior under transient conditions. Analyses of microstructural data derived from transiently heated, irradiated, mixed oxide fuel specimens have allowed the calculation of the degree of nonequilibrium of intragranular bubbles formed during the transient. It is hypothesized that the observed over-pressurization of the intragranular bubbles mechanically loads the fuel within the grain, leading to a stress gradient derived force upon near-grain-surface bubbles, driving them preferentially to the grain boundaries. Using existing models for forced diffusion it can be estimated that the stress derived forces on bubbles are within the same magnitude, and possibly greater, than the forces derived from the thermal gradient

Study of bixin oxidation by ionizing irradiation; Estudo da oxidação da bixina pela radiação ionizante

Energy Technology Data Exchange (ETDEWEB)

Fonseca, Thais N.; Teixeira, Paula S.; Moura, Eduardo de; Geraldo, Áurea Beatriz C., E-mail: thais.fonseca@fatec.sp.gov.br, E-mail: paulateixeirasant@gmail.com, E-mail: emoura@ipen.br, E-mail: ageraldo@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

Brazil is the world's largest producer of anatto, followed by Kenya and Peru. The fruit of the annatto tree is constituted by a capsule containing external spines and internal seeds with reddish coloration, providing a natural pigment which is environmentally efficient, being able to replace synthetic pigments and dyes. The active substance of the pigment is Bixin, which is a type of carotenoid which constitutes a greater percentage of pigment in these seeds and has a lipo soluble character. Bixin reacts with NaOH in a saponification reaction giving norbixin, which is water soluble. It is known that the destination of the dye extracted from the fruit is intended for industry, especially the food industry. The culture of annatto tree brings prospects of development in agricultural programs for medium and small producers, which are able to use decadent areas of other crops. In addition to the food sector, new applications for the pigment helps the development of family farming. The pigment extracted from annatto undergoes a natural oxidation; this work aims to evaluate this phenomenon and also the oxidation of the pigment after the irradiation process. This work also evaluates of the how the oxidation process is affected by irradiation and the modifications introduced to irradiated pigments. Irradiated and nonirradiated samples were characterized by thermogravimetry, UV-vis spectrophotometry and infrared spectroscopy (FTIR). The results are then discussed. (author)

Antioxidant activity for spice oils (1) anti oxidative stability of thyme and caraway oil extracts under UV-irradiation

International Nuclear Information System (INIS)

Atef Ghazy, M.; Shaker, E.S.

2002-01-01

The anti oxidative activity for some spice essential oils have been investigated using thiocyanate method and compared with common natural antioxidant. The antioxidant activity for nine spice oils has been measured at 500 ppm after 13 days. The most potent one was the lemon grass (99.8), followed by orange peel, thyme, and caraway. The activities for these four oils were higher than that for Alpha-tocopherol (87.7%). Petitgrain, and geranium oils have marched activity but less than that for Alpha-tocopherol. No obvious has been found for citronella. fennel, and cardamon oils. The aqueous, butanoic, methanolic and hexanoic extracts for thyme and caraway oil exhibit effective anti oxidative activities under UV irradiation (254 nm) for 6 and 10 hr compared with that for alpha-tocopherol. The anti oxidative effect of thyme and caraway oil extracts were found to be strong and stable towards UV-irradiation, and equal to that for Alpha-tocopherol. Thyme's aqueous and caraway's hexanal extracts were the most potent extracts under the same conditions

Comparative effect of ethylene oxide and gamma irradiation on the chemical sensory and microbial quality of ginger, cinnamon, fennel and fenugreek

International Nuclear Information System (INIS)

Toofanian, F.; Stegeman

1986-01-01

The effect of gamma irradiation and ethylene oxide fumigation on the microbiological and sensory properties of ground cinnamon, ginger, fennel and fenugreek, and on the volatile oil content of ground cinnamon, ginger and fennel was investigated. Ground ginger, cinnamon, fennel and fenugreek were obtained from a Dutch trade company. Ginger originated from China, cinnamon was produced in Indonesia and fennel and fenugreek were produced in India. The samples were ground by the trade companies and divided in three parts. One part was fumigated by the trade companies at ambient temperatures during eight hours with ethylene oxide (EO) at a concentration of 1500/m 3 . The second part was gamma irradiated at room temperature in aluminium/polyethylene bags at the 40 KCi cobalt-60 research source of the pilot plant for food irradiation in Wageningen. The untreated, fumigated and irradiated samples were stored in gas-impermeable packages. It was found that for cinnamon and ginger a 6 KGy dose, for fennel, 6-10 KGy and for fenugreek 6-8 KGy dose were equal in microbial effects to the commercial established fumigation process. No significant change in the volatile oil content of the fumigated or irradiated cinnamon and fennel has been observed. Irradiation of ginger with a dose of 5 KGy resulted in a slight decrease of 14% while fumigated ginger showed no significant loss in volatile oil content. Between the untreated irradiated or fumigated spices no major differences in sensory properties were found

Protective effect of Ginkgo biloba extract against oxidative stress induced by gamma-irradiation in rats

International Nuclear Information System (INIS)

Hashim, I. M.; El-Hindy, H.M.A.; Moussa, S.Z.; Mansour, S.Z.

2013-01-01

This study was to evaluate the prophylactic and therapeutic efficacy of Ginkgo biloba extract against redox imbalance induced by protracted exposure to γ -rays. Rats were exposed to γ-radiation at a dose 2 Gy / week for 4 weeks (γ-radiated group) Ginkgo biloba extract was administered in a dose of 100 mg/kg b. wt. for 7 days before the first dose of γ-radiation and contemned during for exposure period (Ginkgo biloba pre- treated group) and also after the last dose of γ-radiation (Ginkgo biloba post- treated group), these groups were compared with either control or Ginkgo biloba animals. The results reveal obtained significant increases in malondialdhyde and nitric oxide concentrations in blood and liver of γ-irradiated group with concomitant decrease in reduced glutathione content and glutathione peroxidase, superoxide dismutase and catalase activities. Histopathological examinations in the liver revealed a severe damage showed by dilated congested control vein with ruptured endothelium. Vacuolated hapatocytes and extensive cell necrosis were also seen. Note extravagated RBCs within sinusoidal spaces. In addition, the enzymes of liver function and bilirubin content were increased. DNA fragmentation percentage and tumor necrosis factor alpha concentration were also increased in liver. Ginkgo biloba extract administration significantly ameliorated the adverse effects of γ-irradiation in rats. It could be concluded that Ginkgo biloba extract has a role in reducing the oxidative stress of pre or post γ-irradiation on liver tissue of rats

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

Energy Technology Data Exchange (ETDEWEB)

Simon, F.-G., E-mail: franz-georg.simon@bam.de [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany); Holm, O.; Berger, W. [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany)

2013-04-15

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources.

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

International Nuclear Information System (INIS)

Simon, F.-G.; Holm, O.; Berger, W.

2013-01-01

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources

Comparative analyses reveal different consequences of two oxidative stress inducers, gamma irradiation and potassium tellurite, in the extremophile Deinococcus radiodurans

International Nuclear Information System (INIS)

Narasimha, Anaganti; Basu, Bhakti; Apte, Shree Kumar

2014-01-01

Proteomic and mass spectrometric analyses revealed differential responses of D. radiodurans to two oxidative stressors. While both elicited oxidative stress alleviation response, major divergence was observed at the level of DNA repair, metabolic pathways and protein homeostasis. Response to gamma irradiation was focused on DNA repair and ROS scavenging but supported metabolism as well as protein homeostasis. Tellurite, induced oxidative stress alleviation but decreased reducing affected and adversely affected metabolism and protein homeostasis

Determination of tellurium by hydride generation with in situ trapping flame atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Matusiewicz, H.; Krawczyk, M. [Politechn Poznanska, Poznan (Poland)

2007-03-15

The analytical performance of coupled hydride generation - integrated atom trap (HG-IAT) atomizer flame atomic absorption spectrometry (FAAS) system was evaluated for determination of Te in reference material (GBW 07302 Stream Sediment), coal fly ash and garlic. Tellurium, using formation of H{sub 2}Te vapors, is atomized in air-acetylene flame-heated IAT. A new design HG-IAT-FAAS hyphenated technique that would exceed the operational capabilities of existing arrangernents (a water-cooled single silica tube, double-slotted quartz tube or an 'integrated trap') was investigated. An improvement in detection limit was achieved compared with using either of the above atom trapping techniques separately. The concentration detection limit, defined as 3 times the blank standard deviation (3{sigma}), was 0.9 ng mL{sup -1} for Te. For a 2 min in situ preconcentration time (sample volume of 2 mL), sensitivity enhancement compared to flame AAS, was 222 fold, using the hydride generation atom trapping technique. The sensitivity can be further improved by increasing the collection time. The precision, expressed as RSD, was 7.0% (n = 6) for Te. The accuracy of the method was verified using a certified reference material (GBW 07302 Stream Sediment) by aqueous standard calibration curves. The measured Te contents of the reference material was in agreement with the information value. The method was successfully applied to the determination of tellurium in coal fly ash and garlic.

Tritium breeding and release-rate kinetics from neutron-irradiated lithium oxide

International Nuclear Information System (INIS)

Quanci, J.F.

1989-01-01

The research encompasses the measurement of the tritium breeding and release-rate kinetics from lithium oxide, a ceramic tritium-breeding material. A thermal extraction apparatus which allows the accurate measurement of the total tritium inventory and release rate from lithium oxide samples under different temperatures, pressures and carrier-gas compositions with an uncertainty not exceeding 3% was developed. The goal of the Lithium Blanket Module program was to determine if advanced computer codes could accurately predict the tritium production in the lithium oxide blanket of a fusion power plant. A fusion blanket module prototype, was built and irradiated with a deuterium-tritium fusion-neutron source. The tritium production throughout the module was modeled with the MCNP three dimensional Monte Carlo code and was compared to the assay of the tritium bred in the module. The MCNP code accurately predicted tritium-breeding trends but underestimated the overall tritium breeding by 30%. The release rate of tritium from small grain polycrystalline sintered lithium oxide with a helium carrier gas from 300 to 450 C was found to be controlled by the first order surface desorption of mono-tritiated water. When small amounts of hydrogen were added to the helium carrier gas, the first order rate constant increased from the isotopic exchange of hydrogen for tritium at the lithium oxide surface occurring in parallel with the first order desorption process. The isotopic-exchange first order rate constant temperature dependence and hydrogen partial pressure dependence were evaluated. Large single crystals of lithium oxide were fabricated by the vacuum fusion technique. The release rate of tritium from the large single crystals was found to be controlled by diffusion, and the mixed diffusion-desorption controlled release regime

γ-Irradiation assisted synthesis of graphene oxide sheets supported Ag nanoparticles with single crystalline structure and parabolic distribution from interlamellar limitation

Science.gov (United States)

Yue, Yunhao; Zhou, Baoming; Shi, Jie; Chen, Cheng; Li, Nan; Xu, Zhiwei; Liu, Liangsen; Kuang, Liyun; Ma, Meijun; Fu, Hongjun

2017-05-01

This paper reported a method to fabricate graphene oxide sheets supported Ag nanoparticles (AgNPs/GOS) with single crystalline structure and parabolic distribution without surfactant or functional agent. We used imidazole silver nitrate as intercalation precursor into the layers of graphite oxide, and subsequently reduction and growth of interlamellar AgNPs were induced via γ-irradiation. The results illustrated that the synergism of interlamellar limitation of graphite oxide and fragmentation ability of γ-irradiation could prevent coalescent reaction of AgNPs with other oligomeric clusters, and the single crystalline and small-sized (below 13.9 nm) AgNPs were prepared. Moreover, the content and size of AgNPs exhibited parabolic distribution on GOS surface because the graphite oxide exfoliated to GOS from the edge to the central area of layers. In addition, complete exfoliation degree of GOS and large-sized AgNPs were obtained simultaneously under suitable silver ions concentration. Optimized composites exhibited outstanding surface-enhanced Raman scattering properties for crystal violet with enhancement factor of 1.3 × 106 and detection limit of 1.0 × 10-7 M, indicating that the AgNPs/GOS composites could be applied to trace detection of organic dyes molecules. Therefore, this study presented a strategy for developing GOS supported nanometal with single crystalline structure and parabolic distribution based on γ-irradiation.

Preparation of the Nanostructured Radioisotope Metallic Oxide by Neutron Irradiation for Use as Radiotracers

Directory of Open Access Journals (Sweden)

Sang-Ei Seo

2017-10-01

Full Text Available Metallic oxides manganese dioxide (MnO2, samarium oxide (Sm2O3, and dysprosium oxide (Dy2O3 with nanorod-like structures were synthesized by the hydrothermal synthesis method, respectively. Subsequently, the nanostructured radioisotopes MnO2 with Mn-56, Sm2O3 with Sm-153, and Dy2O3 with Dy-165 were prepared by neutron irradiation from the HANARO research reactor, respectively. The three different elements, Mn, Sm, and Dy, were selected as radiotracers because these elements can be easily gamma-activated from neutrons (activation limits: 1 picogram (Dy, 1–10 picogram (Mn, 10–100 picogram (Sm. Furthermore, the synthesized radioisotopes can be used as radiotracers in Prompt Gamma Neutron Activation Analysis as the rare earth metals Dy and Sm were not present in the Korean environment. The successful synthesis of the radioisotope metallic oxides was confirmed by Transmission Electron Microscopy (TEM, Energy Dispersive X-ray Spectrometry (EDS, X-ray Diffraction (XRD analysis, and gamma spectroscopy analysis. The synthesized nanostructured radioisotope metallic oxides may be used as radiotracers in scientific, environmental, engineering, and industrial fields.

Irradiation performance of oxide dispersion strengthened copper alloys to 150 dpa at 415 degree C

International Nuclear Information System (INIS)

Edwards, D.J.; Kumar, A.S.; Anderson, K.R.; Stubbins, J.F.; Garner, F.A.; Hamilton, M.L.

1991-11-01

Results have been obtained on the post-irradiation properties of various oxide dispersion strengthened copper alloys irradiated from 34 to 150 dpa at 415 degrees C in the Fast Flux Test Facility. The GlidCop alloys strengthened by Al 2 O 3 continue to outperform other alloys with respect to swelling resistance, and retention of both electrical conductivity and yield strength. Several castable ODS alloys and a Cr 2 O 3 -strengthened alloy show increasingly poor resistance to radiation, especially in their swelling behavior. A HfO 2 -strengthened alloy retains most of its strength and its electrical conductivity reaches a constant level after 50 dpa, but it exhibits a higher residual radioactivity

Thermoluminescence of europium-doped zinc oxide exposed to beta particle irradiation

Energy Technology Data Exchange (ETDEWEB)

Iriqui R, J. L.; Cruz V, C. [Universidad de Sonora, Departamento de Investigacion en Polimeros y Materiales, Apdo. Postal 130, 83000 Hermosillo, Sonora (Mexico); Bernal, R. [Universidad de Sonora, Departamento de Investigacion en Fisica, Apdo. Postal 5-088, 83000 Hermosillo, Sonora (Mexico); Castano, V. M., E-mail: jorgeiriqui@gimmunison.com [UNAM, Instituto de Fisica, Centro de Fisica Aplicada y Tecnologia Avanzada, Apdo. Postal 1-1010, 76000 Queretaro, Qro. (Mexico)

2015-10-15

Full text: Zn O is a promising material for a range of optoelectronics applications, due to its direct wide band gap (E{sub g} ∼3.3 eV at 300 K) and large exciton binding energy (60 MeV). Its applications include UV light emitters, varistors, surface acoustic wave devices, piezoelectric transducers, and chemical and gas sensing. Rare-earth activation of phosphors has long been seen as an effective process since coupling energy into the rare-earth-ion site, either by ionization, charge exchange or a resonance energy process, results in light production. It is reported that Europium modifies the response thermoluminescence (Tl) for pure zinc oxide, when is irradiated with X-ray, created a peak at 365 degrees C. In this work, Zn O:Eu phosphors were synthesized by a chemical method. Some samples were exposed to beta particle irradiation for doses ranging from 1 up to 100 Gy. Tl response as a function of dose is linear throughout the studied dose range. The glow curve exhibits three maxima, centered at 176, 279 and 340 degrees C. The reusability studies obtained after ten repeated cycles of annealing irradiation readout for the Zn O:Eu shows that the variation in the Tl response is ten percent and tends to stabilization. The results indicate that these new Zn O:Eu phosphors are promising detectors and dosimeters for beta radiation. The structural and morphological characterization was carried out by X-ray diffraction and scanning electron microscopy, respectively. (Author)

The influence of the UV irradiation intensity on photocatalytic activity of ZnAl layered double hydroxides and derived mixed oxides

Directory of Open Access Journals (Sweden)

Hadnađev-Kostić Milica S.

2012-01-01

Full Text Available Layered double hydroxides (LDHs have been studied to a great extent as environmental-friendly complex materials that can be used as photocatalysts or photocatalyst supports. ZnAl layered double hydroxides and their derived mixed oxides were chosen for the investigation of photocatalytic performances in correlation with the UV intensities measured in the South Pannonia region. Low supersaturation coprecipitation method was used for the ZnAl LDH synthesis. For the characterization of LDH and thermal treated samples powder X-ray diffraction (XRD, scanning electron microscopy (SEM, electron dispersive spectroscopy (EDS, nitrogen adsorption-desorption were used. The decomposition of azodye, methylene blue was chosen as photocatalytic test reaction. The study showed that the ZnAl mixed oxide obtained by thermal decomposition of ZnAl LDH has stable activity in the broader UV light irradiation range characterizing the selected region. Photocatalytic activity could be mainly attributed to the ZnO phase, detected both in LDH and thermally treated samples. The study showed that the ZnAl mixed oxide obtained by the calcination of ZnAl LDH has a stable activity within the measured UV light irradiation range; whereas the parent ZnAl LDH catalyst did not perform satisfactory when low UV irradiation intensity is implied.

Effects of CO, O2, NO, H2O, and irradiation temperature on the radiation-induced oxidation of SO2

International Nuclear Information System (INIS)

Tokunaga, Okihiro; Nishimura, Koichi; Suzuki, Nobutake; Washino, Masamitsu

1977-01-01

When a SO 2 -H 2 O-O 2 -N 2 gaseous mixture was irradiated by electron beams of 1.5 MeV, SO 2 was easily oxidized to H 2 SO 4 . Effects of CO, O 2 , NO, H 2 O, and irradiation temperature on the radiation-induced oxidation of SO 2 were studied by measuring the SO 2 concentration gas chromatographically. The G(-SO 2 ) increased greatly at the addition of a small amount of O 2 , and then decreased gradually with an increase in the O 2 concentration, i.e., the G(-SO 2 ) values were 0.9, 8.0, and 5.3 for the 0, 0.1, and 20% O 2 concentrations at 100 0 C, respectively (Fig.4). The G(-SO 2 ) was independent of the H 2 O concentration in the range of 0.84 to 8.4% (Fig.5). The G(-SO 2 ) decreased with a rise in the irradiation temperature (Fig.6) and an apparent activation energy of the oxidation reaction of SO 2 obtained was -4.2 kcal.mol -1 . The effects of CO, NO, and O 2 on the G(-SO 2 ) showed that SO 2 was mainly oxidized by OH and O and that the contribution of OH to the oxidation of SO 2 increased with an increase in the O 2 concentration (Table 1). The rate constants for the reactions of SO 2 with OH and O, obtained from competitive reactions of SO 2 with CO and O 2 , were 5.4 x 10 11 cm 3 .mol -1 .sec -1 and 5.0 x 10 11 cm 3 .mol -1 .sec -1 , respectively. (auth.)

Separation of 99Tc from irradiated molybdenum oxide by extraction with trioctilamine

International Nuclear Information System (INIS)

Carvalho, O.G. de.

1979-01-01

A separation method of sup( 99 m)Tc, from irradiated molybdenum oxide, by extraction with trioctilamino in 1,2 dichloroethane, 2% v/v is studied. Two preliminary studies are done: 1) Stablishment of the shaking time necessary to reach the equilibrium between the organic and the aqueous phase; 2) Choice of the concentration of solution of TOA in 1,2 dichloroethane to obtain the best separation conditions of sup( 99 m)Tc. After stablishing these two parameters, the study of extraction in solutions of hydrochloric nitric and sulfuric acids in different concentrations is done, followed by the study of the variation of extraction percentage of sup( 99 m)Tc in relation to the molybdenum oxide mass and the back-extraction of sup( 99 m)Tc to the aqueous phase with solutions of perchloric acid 1,0 and 0,1 N and ammonium hydroxide 1,0 N. (Author) [pt

A combination of He-Ne laser irradiation and exogenous NO application efficiently protect wheat seedling from oxidative stress caused by elevated UV-B stress.

Science.gov (United States)

Li, Yongfeng; Gao, Limei; Han, Rong

2016-12-01

The elevated ultraviolet-B (UV-B) stress induces the accumulation of a variety of intracellular reactive oxygen species (ROS), which seems to cause oxidative stress for plants. To date, very little work has been done to evaluate the biological effects of a combined treatment with He-Ne laser irradiation and exogenous nitric oxide (NO) application on oxidative stress resulting from UV-B radiation. Thus, our study investigated the effects of a combination with He-Ne laser irradiation and exogenous NO treatment on oxidative damages in wheat seedlings under elevated UV-B stress. Our data showed that the reductions in ROS levels, membrane damage parameters, while the increments in antioxidant contents and antioxidant enzyme activity caused by a combination with He-Ne laser and exogenous NO treatment were greater than those of each individual treatment. Furthermore, these treatments had a similar effect on transcriptional activities of plant antioxidant enzymes. This implied that the protective effects of a combination with He-Ne laser irradiation and exogenous NO treatment on oxidative stress resulting from UV-B radiation was more efficient than each individual treatment with He-Ne laser or NO molecule. Our findings might provide beneficial theoretical references for identifying some effective new pathways for plant UV-B protection.

Formation of defects in tellurium at various levels of gravitation

International Nuclear Information System (INIS)

Parfen'ev, R.V.; Farbshtejn, I.I.; Shul'pina, I.L.; Yakimov, S.V.; Shalimov, V.P.; Turchaninov, A.M.

2002-01-01

One investigated into effect of gravitation conditions during tellurium crystallization (ranging from microgravitation up to increased gravitation - 5g 0 ) on concentration of neutral (N D ) and electrically active (N AD ) acceptor structure defects in specimens grown both under complete remelting of parent ingot and under directed recrystallization of ingot with inoculation. N AD and N D concentrations and their distribution along the specimen depth were determined on the basis of analysis of electrical characteristics (conductivity and the Hall effect) measured along ingots within 1.6-300 K temperature range. The results were compared with characteristics of specimens grown following the similar program under normal conditions. At complete remelting under microgravitation one detected attributes of strong supercooling and spontaneous crystallization, as well as, of specimen resistance oscillation by its depth caused by N D modulation [ru

Chemical consequences of the neutron irradiation of ionic antimony oxides and Fe Sb2O4

Energy Technology Data Exchange (ETDEWEB)

Facetti, J F [Asuncion Nacional Univ. (Paraguay). Inst. de Ciencias

1970-01-01

The chemical consequences fo the neutron irradiation of ionic antimony oxides and Fe Sb2O4 are studied. The nature of the Sb-O2 bond effects the yield of SbV the higher the yield the more covalent the bond. In addition, the Fe Sb2O4 obeys the Maddock's rule.

Effectiveness of ethylene oxide and gamma irradiation on the microbiological population of three types of paprika

International Nuclear Information System (INIS)

Franco, S.L.; Gimenez, J.L.; Sanchez, F.M.; Romojaro, F.

1986-01-01

The effectiveness of ethylene oxide and the gamma irradiation sterilizing treatments on the microbiological population was studied in three types of Spanish paprika, stored in a cold chamber (4 0 C) and at room temperature (16-38.8 0 C) over an experimental period of 285 days. The controlled microorganisms were: mesophilic aerobes, coliforms, sulfite reducing anaerobes, yeasts, molds, and Salmonella. The presence of aflatoxins was also studied. The results showed that both sterilizing treatments reduced the microbiological population to below the permissible levels recommended by the International Commission on Microbiological Specification for Food. Nevertheless, it was interesting that the gamma irradiation treatment was more effective

Use of Iodine-131 to Tellurium-132 Ratios for Assessing the Relationships between Human Inhaled Radioactivity and Environmental Monitoring after the Accident in Fukushima

Directory of Open Access Journals (Sweden)

Koji Uchiyama

2018-03-01

Full Text Available Significant differences in findings were seen between the intake amounts of iodine-131 that were derived from direct measurements and the estimated intake from environmental monitoring data at the Fukushima accident. To clarify these discrepancies, we have investigated the iodine-131 and tellurium-132 body burdens of five human subjects, who after being exposed to a radioactive plume, underwent 21.5 h whole body counter measurements at Fukui Prefectural Hospital, so clear intake scenario and thyroid counter measurement data were available. To determine the iodine-131 and tellurium-132 body burdens, we introduced a new method of whole body counter calibration composed of a self-consistent approach with the time-dependent correction efficiency factors concept. The ratios of iodine-131 to tellurium-132, ranging from 0.96 ± 0.05 to 2.29 ± 0.38, were consistent with results of the environmental measurements. The 24 h iodine uptake values ranging from 12.1–16.0% were within euthyroid range in Japanese people. These results suggest, even if the relatively low thyroid iodine uptake in the Japanese population was taken into consideration, that there is no doubt about the consistency between direct measurements and environmental monitoring data. Adequate intake scenario is suggested to be principally important to estimate the inhaled radioactivity in areas in or around nuclear accidents.

Azo dyes degradation using TiO2-Pt/graphene oxide and TiO2-Pt/reduced graphene oxide photocatalysts under UV and natural sunlight irradiation

Science.gov (United States)

Rosu, Marcela-Corina; Coros, Maria; Pogacean, Florina; Magerusan, Lidia; Socaci, Crina; Turza, Alexandru; Pruneanu, Stela

2017-08-01

The photocatalytic degradation of azo dyes with different structures (amaranth, sunset yellow and tartrazine) using TiO2-Pt nanoparticles (TPt), TiO2-Pt/graphene oxide (TPt-GO) and TiO2-Pt/reduced graphene oxide (TPt-rGO) composites were investigated in the presence of UV and natural sunlight irradiation. The composites were prepared by a combined chemical-thermal method and characterized by Transmission Electron Microscopy (TEM), X-ray powder diffraction (XRD), Infrared (FTIR) and UV-Vis spectroscopy. The modification of TiO2-Pt with graphene oxide shifted its optical absorption edge towards the visible region and increased its photocatalytic activity under UV and natural sunlight irradiation. The efficiency of catalysts on azo dyes degradation (in similar conditions) reached high values (above 99%) under sunlight conditions, proving the remarkable photocatalytic activities of obtained composites. TPt-GO nanocomposite exhibited higher photoactivity than TPt or TPt-rGO, demonstrating degradation efficiencies of 99.56% for amaranth, 99.15% for sunset yellow and 96.23% for tartrazine. The dye photodegradation process follows a pseudo-first-order kinetic with respect to the Langmuir-Hinshelwood reaction mechanism. A direct dependence between azo dyes degradation rate and chemical structure of dyes has been observed.

Exploratory studies of element substitutions in synthetic tetrahedrite. Part II. Selenium and tellurium as anions in Zn-Fe tetrahedrites

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

1999-01-01

-free) compositons do not materialize. The substituted Se tetrahedrite coexists with Cu3SbSe3, (iron-bearing) Cu2-xSe, Cu3SbSe4 plus/minus low Zn-sulfide melt. Selenium does not adopt the role of cation and tellurium that of anion in the tetrahedrite structure. The explanation of the severely restricted composition...

Formation of chromium oxide nanoparticles by gamma irradiation of chromate solutions

International Nuclear Information System (INIS)

Alrehaily, L.M.; Joseph, J.M.; Wren, J.C.; Guzonas, D.A.

2012-09-01

provide nucleation sites on which Cr VI (aq) can continually adsorb and be reduced. The particles that are formed grow as Cr (OH) 3 . The Cr (OH) 3 particles grow to a size (10-15 nm) that is regulated by the steady-state redox conditions that are established at the aqueous-solid interface in the presence of continuous irradiation. At longer times, these particles agglomerate to form larger, multi-faceted particles of thermodynamically more stable Cr 2 O 3 . The sizes of these chromium oxide particles ranged from 20 to 40 nm, depending on the initial chromate concentration. Our study demonstrates the ability of water radiolysis to alter the solubility of a transition metal. It also shows that irradiation affects the formation and stability of colloidal particles and, hence, the deposition or precipitation of corrosion products on in-core structural surfaces. (authors)

The effect of hydrostatic pressure on the anomalous sign reversal of the Hall coefficient in tellurium

International Nuclear Information System (INIS)

Balynas, V.; Dobrovolskis, Z.; Krotkus, A.; Hoerstel, W.

1981-01-01

In order to obtain information about the pressure behaviour of the higher lying second conduction band the dependences of the Hall coefficient of single crystalline tellurium on temperature (300 to 500 K) have been measured at atmospheric pressure and hydrostatic pressures of 500 and 800 MPa. The separation between the two conduction bands in Te decreases with increasing pressure. The anomalous sign reversal of the Hall coefficient can be well explained by a double-conduction band model

Ultraviolet A irradiation of the eye activates a nitric oxide-dependent hypothalamo-pituitary pro-opiomelanocortin pathway and modulates the functions of Langerhans cells.

Science.gov (United States)

Hiramoto, Keiichi

2009-06-01

Ultraviolet A (UV-A) radiation decreases Langerhans cells (LC) in the skin specifically at the site of exposure. Unexpectedly, UV-A irradiation of the eye has been found systemically downregulating epidermal LC in mice. Male C57BL/6j mice and an inducible type of nitric oxide synthase knockout mice (iNOS(-/-)) were used in this study. The eye or ear was locally exposed to UV-A after covering the remaining body surface with aluminum foil at a dose of 110 kJ/m(2) using a sunlamp. Localized UV-A irradiation of the eye downregulated epidermal LC. The hypophysectomy strongly inhibited the UV-A-induced downregulation of LC. To elucidate the pathway by UV-A irradiation of the eye, the effect of a bilateral ciliary ganglionectomy and denervation of the optic nerves was examined. Optic nerve denervation strongly inhibited LC downregulation in response to localized irradiation of the eye. Furthermore, no LC downregulation in response to localized UV-A irradiation of the eye was observed in iNOS(-/-) mice. These results clearly indicate that a signal evoked by UV-A irradiation of the eye is transmitted in a nitric oxide-dependent manner through the optic nerves to the hypothalamo-pituitary pro-opiomelanocortin system.

Low field leakage current on ultra-thin gate oxides after ion or electron beam irradiations; Courant de fuite aux champs faibles d'oxydes ultra-minces apres irradiations avec des faisceaux d'ions et d'electrons

Energy Technology Data Exchange (ETDEWEB)

Ceschia, M.; Paccagnella, A.; Sandrin, S. [Universita di Padova, Dipt. di Elettronica e Informatica, Padova (Italy); Paccagnella, A. [Istituto Nazionale per la Fisica della Materia, INFM, Unita di Padova (Italy); Ghidini, G. [ST-Microelectronics, Agrate Brianza (Italy); Wyss, J. [Universita di Padova, Dipt. di Fisica, Padova (Italy)

1999-07-01

In contemporary CMOS 0.25-{mu}m technologies, the MOS gate oxide (thickness {approx_equal} 5 nm) shows a low-field leakage current after radiation stresses, i.e. the radiation induced leakage current (RILC). RILC is generally attributed to a trap assisted tunneling (TAT) of electrons through neutral oxide traps generated by radiation stress. RILC has been investigated on ultra-thin oxides irradiated with 158 MeV {sup 28}Si ions or 8 MeV electrons. 3 main results are worth being quoted: 1) ion or electron beam irradiation can produce RILC with similar characteristics. Even the dose dependence of RILC is similar in the 2 cases, despite the large LET difference (about a factor of 10{sup +4}), 2) RILC is not a constant as a function of time, it tends to decrease when an oxide field (few MV/cm) is applied for (tens of) thousands seconds. On the other hand, RILC stays constant in devices kept at low bias, and 3) if a pulsed gate voltage is applied during irradiation, RILC is reduced with respect to the zero-field case. (A.C.)

Charge accumulation in the buried oxide of SOI structures with the bonded Si/SiO2 interface under γ-irradiation: effect of preliminary ion implantation

International Nuclear Information System (INIS)

Naumova, O V; Fomin, B I; Ilnitsky, M A; Popov, V P

2012-01-01

In this study, we examined the effect of preliminary boron or phosphorous implantation on charge accumulation in the buried oxide of SOI-MOSFETs irradiated with γ-rays in the total dose range (D) of 10 5 –5 × 10 7 rad. The buried oxide was obtained by high-temperature thermal oxidation of Si, and it was not subjected to any implantation during the fabrication process of SOI structures. It was found that implantation with boron or phosphorous ions, used in fabrication technologies of SOI-MOSFETs, increases the concentration of precursor traps in the buried oxide of SOI structures. Unlike in the case of boron implantation, phosphorous implantation leads to an increased density of states at the Si/buried SiO 2 interface during subsequent γ-irradiation. In the γ-irradiated SOI-MOSFETs, the accumulated charge density and the density of surface states in the Si/buried oxide layer systems both vary in proportion to k i ln D. The coefficients k i for as-fabricated and ion-implanted Si/buried SiO 2 systems were evaluated. From the data obtained, it was concluded that a low density of precursor hole traps was a factor limiting the positive charge accumulation in the buried oxide of as-fabricated (non-implanted) SOI structures with the bonded Si/buried SiO 2 interface. (paper)

Photocatalytic activity of silver oxide capped Ag nanoparticles constructed by air plasma irradiation

Science.gov (United States)

Fang, Yingcui; Wu, Qingmeng; Li, Huanhuan; Zhang, Bing; Yan, Rong; Chen, Junling; Sun, Mengtao

2018-04-01

We construct a kind of structure of silver oxide capped silver nanoparticles (AgNPs) by cost-efficient air plasma irradiation, and study its visible-light driven photocatalytic activity (PA). By controlling the oxidization time, the relationship between the intensity of the localized surface plasmon resonance (LSPR) and the PA is well established. The PA reaches the maximum when the LSPR of AgNPs is nearly completely damped (according to absorption spectra); however, under this condition, the LSPR still works, confirmed with the high efficient selective transformation of p-Aminothiophenol (PATP) to p, p'-dimercaptoazobenzene (DMAB) under visible light. The mechanism of the LSPR damping induced PA improvement is discussed. We not only provide a cost-efficient approach to construct a LSPR strong damping structure but also promote the understanding of LSPR strong damping and its relationship with photocatalysis.

Revision and extension to the analysis of the third spectrum of tellurium: Te III

International Nuclear Information System (INIS)

Tauheed, A.; Naz, A.

2011-01-01

The spectrum of doubly ionized tellurium atom (Te III) has been investigated in the vacuum ultraviolet wavelength region. The ground configuration of Te III is 5s 2 5p 2 and the excited configurations are of the type 5s 2 5p nl. The core excitation leads to a 5s5p 3 configuration. Cowan's multi-configuration interaction code was utilized to predict the ion structure. The observed spectrum of tellurium was recorded on a 3-m normal incidence vacuum spectrograph of Antigonish Laboratory (Canada) in the wavelength region of 300 - 2000 A by using a triggered spark light source for the excitation of the spectrum. The 5s 2 5p 2 - [ 5s 2 5p (5d + 6d + 7d + 6s + 7s + 8s) + 5s5p 3 ] transition array has been analyzed. Previously reported levels by Joshi et al have been confirmed while the older analysis by Crooker and Joshi has been revised and extended to include the 5s 2 5p (5d, 6d, 7d, 6s,7s, 8s) and 5s5p 3 configurations. Least-squares- fitted parametric calculations were used to interpret the final results. One hundred and fifty spectral lines have been identified to establish 60 energy levels. Our wavelength accuracy for unblended and sharp lines is better than ±0.005 A. The ionization potential of Te III was found to be 224550 ± 300 cm -1 (27.841 ± 0.037eV).

Role of taurine as a treatment for oxidative damage and sperm head abnormalities in irradiated mice and their male offspring

International Nuclear Information System (INIS)

El-Dawy, H.; Tawfik, S.S.; EI-Khafif, M.; Ragab, M.H.

2007-01-01

The efficiency of taurine therapy in treatment of male mice exposed to a dose of (3 Gy) whole body gamma irradiation and their male offspring was studied. Irradiated mice showed significant increase in plasma malonaldehyde (MDA) level and sperm head abnormality counts in all experiment interval times 1, 3 and 5 weeks. Administration of taurine (1% in drinking water) post-irradiation resulted in significant decrease in the effect of irradiation on MDA level and sperm head abnormalities count. The efficiency of taurine as radiotherapeutic agent is greatly dependent on its chemical properties as strong oxidants scavenger and biological activities as osmoregulator and membrane stabilizer. The probable mechanism of taurine was discussed, as it is a sulphydryl, heterocyclic-nitrogenous and pharmacological therapy

Kinetics of Phenol Degradation in Aqueous Solution Oxidized under Low Frequency Ultrasonic Irradiation

Directory of Open Access Journals (Sweden)

Marwan Marwan

2014-06-01

Full Text Available Phenol is categorized as a refractory pollutant and its presence in water stream is strictly limited according to the government regulation. The present study investigated the degra-dation of phenol in aqueous solution by the effect of ultrasound. The process took place in a 500 ml glass reactor equipped with magnetic stirring and irradiated by low frequency (28 kHz ultrasound from a horn type probe. Ultrasonic irradiation was found to enhance oxidation rates at ambient conditions, compared to other approaches. Optimum conditions were observed at a stirring speed of 400 rpm and temperature of 30 C in acidic solution. It was revealed that the phenol degradation was the first order kinetics with respect to phenol. A low value of the activation energy 6.04 kcal/mol suggested that diffusional steps were rate determining during the phenol decomposition. It also confirmed that phenol was mostly degraded in the film region and less occurred in the bulk solution.

Study of the thermal oxidation of titanium and zirconium under argon ion irradiation in the low MeV range (E = 15 MeV)

International Nuclear Information System (INIS)

Do, N.-L.

2012-01-01

We have shown that argon ion irradiation between 1 and 15 MeV produces damage on both titanium and zirconium surfaces, taking the form of accelerated oxidation and/or craterization effects, varying as a function of the projectile energy and the annealing atmosphere (temperature and pressure) simulating the environmental conditions of the fuel/cladding interface of PWR fuel rods. Using AFM, we have shown that the titanium and zirconium surface is attacked under light argon ion bombardment at high temperature (up to 500 C) in weakly oxidizing medium (under rarefied dry air pressure ranging from 5,7 10 -5 Pa to 5 10 -3 Pa) for a fixed fluence of about 5 10 14 ions.cm -2 . We observed the formation of nano-metric craters over the whole titanium surface irradiated between 2 and 9 MeV and the whole zirconium surface irradiated at 4 MeV, the characteristics of which vary depending on the temperature and the pressure. In the case of the Ar/Ti couple, the superficial damage efficiency increases when the projectile energy decreases from 9 to 2 MeV. Moreover, whereas the titanium surface seems to be transparent under the 15-MeV ion beam, the zirconium surface exhibits numerous micrometric craters surrounded by a wide halo. The crater characteristics (size and superficial density) differ significantly from that observed both in the low energy range (keV) where the energy losses are controlled by ballistic collisions (Sn) and in the high energy range (MeV - GeV) where the energy losses are controlled by electronic excitations (Se), which was not completely unexpected in this intermediate energy range for which combined Sn - Se stopping power effects are possibly foreseen. Using XPS associated to ionic sputtering, we have shown that there is an irradiation effect on thermal oxidation of titanium, enhanced under the argon ion beam between 2 and 9 MeV, and that there is also an energy effect on the oxide thickness and stoichiometry. The study conducted using Spectroscopic

Light-Induced Tellurium Enrichment on CdZnTe Crystal Surfaces Detected by Raman Spectroscopy

International Nuclear Information System (INIS)

Hawkins, Samantha A.; Villa-Aleman, Eliel; Duff, Martine C.; Hunter, Doug B.; Burger, Arnold; Groza, Michael; Buliga, Vladimir; Black, David R.

2008-01-01

CdZnTe (CZT) crystals can be grown under controlled conditions to produce high-quality crystals to be used as room-temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro-Raman spectroscopy. The growth of Te rich areas on the surface was induced by low-power lasers. The growth was observed versus time with low-power Raman scattering and was observed immediately under higher-power conditions. The detector response was also measured after induced Te enrichment.

Dissolution behavior of irradiated mixed oxide fuel with short stroke shearing for fast reactor reprocessing

International Nuclear Information System (INIS)