Tellurium self-diffusion and point defects in lead telluride

International Nuclear Information System (INIS)

Simirskij, Yu.N.; Firsova, L.P.

1982-01-01

Method of radioactive indicators was used to determine factors of tellurium self-diffusion in lead telluride with different deviation of the composition from stoichiometric in the range of enrichment by tellurium. It was found that at 973 K factors of tellurium self-diffusion in lead telluride depend slightly on the vapor pressure of tellurium equilibrium with solid phase

Interaction of tellurium and tellurium-containing semiconductor compounds with solutions of HI-HNO3-H2O system

International Nuclear Information System (INIS)

Tomashik, V.N.; Sava, A.A.; Tomashik, Z.F.

1994-01-01

As a result of experimental investigations and physical-chemical simulation are established regularities of solution of semiconducting tellurium-containing compounds in HI-HNO 3 -H 2 O systems. In HNO 3 -HI system solutions enriched by HNO 3 are not used for CdTe treatment but HI enriched solution are similar in composition with I 2 -HI solutions. Solution of the given tellurium-containing materials proceeds by a chemical mechanism and is determined by tellurium oxidation with iodine

Tellurium release and deposition during the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Osetek, D.J.; Hobbins, R.R.; Jessup, J.S.

1984-09-01

The estimated behavior of tellurium during and after the accident at the Three Mile Island Unit-2 is presented. The behavior is based on all available measurement data for /sup 129m/Te, 132 Te, stable tellurium ( 126 Te, 128 Te and 130 Te), and best estimate calculations of tellurium release and transport. The predicted release was calculated using current techniques that relate release rate to fuel temperature and holdup of tellurium in zircaloy until significant oxidation occurs. The calculated release fraction was low, approx. 7%, but the total measured release for samples analyzed to date is about 5.8%. Of the measured tellurium about 2.4, 1.8, 0.88, 0.42, 0.17 and 0.086% of core inventory were in the containment sump water, upper plenum assembly surfaces, containment solids in the sump water, makeup and purification demineralizer, containment inside surface, and the reactor primary coolant, respectively. A significant fraction (54%) of the tellurium calculated to be retained on the upper plenum surfaces (4.61% of the core inventory) was deposited during the high pressure injection of coolant at about 200 min after the reactor scram. Comparison of tellurium behavior with in-pile and out-of-pile tests strongly suggests that zircaloy holds tellurium until significant cladding oxidation occurs

Tellurium behavior during and after the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Osetek, D.J.; Hobbins, R.R.

1984-01-01

The estimated behavior of tellurium during and after the accident at the Three Mile Island Unit-2 is presented. The behavior is based on all available measurement data for /sup 129m/Te, 132 Te and stable tellurium ( 126 Te, 128 Te and 130 Te), and best estimate calculations of tellurium release and transport. The predicted release was calculated using current techniques that relate release rate to fuel temperature and holdup of tellurium in zircaloy until significant oxidation occurs. The calculated release fraction was low, approximately 7%, but the total measured release for samples analyzed to date is about 4.0%. Of the measured tellurium about 2.4, 0.88, 0.42, 0.17 and 0.086% of core inventory were in the containment sump water, containment solids in water, makeup and purification demineralizer, containment inside surface, and the reactor primary coolant, respectively. A significant fraction (54%) of the calculated tellurium retained on the upper plenum surfaces (4.61% of the core inventory) was deposited during the high pressure injection of coolant at about 200 minutes after the reactor scram. Comparison of tellurium behavior with inpile and out-of-pile tests strongly suggests that zircaloy holds tellurium until significant cladding oxidation occurs

Peroxide coordination of tellurium in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

2016-02-15

Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fission product tellurium chemistry from fuel to containment

International Nuclear Information System (INIS)

McFarlane, J.

1996-01-01

Chemical equilibrium calculations were performed on the speciation of tellurium in-core and inside the primary heat transport system (PHTS) under loss-of-coolant accident conditions. Data from recent Knudsen-cell experiments on the volatilization of Cs 2 Te were incorporated into the calculation. These data were used to recalculate thermodynamic quantities for Cs 2 Te(g), including Δ f G o (298 K)= -118±9 kJ.mol -1 . The description of the condensed high-temperature cesium-tellurium phase was expanded to include Cs 2 Te 3 (c) in addition to Cs 2 Te(c). These modifications were incorporated into the database used in the equilibrium calculations; the net effect was to stabilize the condensed cesium-tellurium phase and reduce the vapour pressure of Cs 2 Te(g) between 1200 and 1600 K. The impact of tellurium speciation in containment, after release from the PHTS, is discussed along with the possible effect of tellurium on iodine chemistry. (author) 10 figs., 5 tabs., 21 refs

Fission product tellurium chemistry from fuel to containment

Energy Technology Data Exchange (ETDEWEB)

McFarlane, J [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

1996-12-01

Chemical equilibrium calculations were performed on the speciation of tellurium in-core and inside the primary heat transport system (PHTS) under loss-of-coolant accident conditions. Data from recent Knudsen-cell experiments on the volatilization of Cs{sub 2}Te were incorporated into the calculation. These data were used to recalculate thermodynamic quantities for Cs{sub 2}Te(g), including {Delta}{sub f}G{sup o}(298 K)= -118{+-}9 kJ.mol{sup -1}. The description of the condensed high-temperature cesium-tellurium phase was expanded to include Cs{sub 2}Te{sub 3}(c) in addition to Cs{sub 2}Te(c). These modifications were incorporated into the database used in the equilibrium calculations; the net effect was to stabilize the condensed cesium-tellurium phase and reduce the vapour pressure of Cs{sub 2}Te(g) between 1200 and 1600 K. The impact of tellurium speciation in containment, after release from the PHTS, is discussed along with the possible effect of tellurium on iodine chemistry. (author) 10 figs., 5 tabs., 21 refs.

Quantitative analysis of tellurium in simple substance sulfur

International Nuclear Information System (INIS)

Arikawa, Yoshiko

1976-01-01

The MIBK extraction-bismuthiol-2 absorptiometric method for the quantitative analysis of tellurium was studied. The method and its limitation were compared with the atomic absorption method. The period of time required to boil the solution in order to decompose excess hydrogen peroxide and to reduce tellurium from 6 valance to 4 valance was examined. As a result of experiment, the decomposition was fast in the alkaline solution. It takes 30 minutes with alkaline solution and 40 minutes with acid solution to indicate constant absorption. A method of analyzing the sample containing tellurium less than 5 ppm was studied. The experiment revealed that the sample containing a very small amount of tellurium can be analyzed when concentration by extraction is carried out for the sample solutions which are divided into one gram each because it is difficult to treat several grams of the sample at one time. This method also is suitable for the quantitative analysis of selenium. This method showed good addition effect and reproducibility within the relative error of 5%. The comparison between the calibration curve of the standard solution of tellurium 4 subjected to the reaction with bismuthiol-2 and the calibration curve obtained from the extraction of tellurium 4 with MIBK indicated that the extraction is perfect. The result by bismuthiol-2 method and that by atom absorption method coincided quite well on the same sample. (Iwakiri, K.)

Facile electrochemical synthesis of tellurium nanorods and their photoconductive properties

Energy Technology Data Exchange (ETDEWEB)

Li, H.H. [Center for Photon Manufacturing Science and Technology, School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); Zhang, P. [Dongguan University of Technology, Dongguan-523808 (China); School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou - 510275 (China); Liang, C.L. [Instrumental Analysis and Research Center, SunYat-sen University, Guangzhou - 510275 (China); Yang, J. [School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); Zhou, M. [Center for Photon Manufacturing Science and Technology, School of Materials Science and Engineering, Jiangsu University, Zhenjiang - 212013 (China); The State Key Laboratory of Tribology, Tsinghua University, Beijing - 10084 (China); Lu, X.H. [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou - 510275 (China); Hope, G.A. [School of Biomolecular and Physical Sciences, Griffith University, Nathan - Qld 4111 (Australia)

2012-10-15

Tellurium nanorods have been successfully fabricated by template and surfactant-free electrochemical technique from an aqueous solution at room temperature. The as-prepared tellurium nanorods were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectrometry, UV-vis spectroscopy and photoluminescence spectroscopy. Films based on tellurium nanorods were constructed to study the photoresponse and I-V curves. These photoresponse measurements demonstrate that tellurium nanorods exhibited enhanced conductivity under illumination compared to in the dark measurement. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of tellurium thin films electrodeposition from acidic citric bath

Energy Technology Data Exchange (ETDEWEB)

Kowalik, Remigiusz; Kutyła, Dawid [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland); Mech, Krzysztof [AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, al. A. Mickiewicza 30, Krakow (Poland); Żabiński, Piotr, E-mail: rkowalik@agh.edu.pl [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland)

2016-12-01

This work presents the description of the electrochemical process of formation thin tellurium layers from citrate acidic solution. The suggested methodology consists in the preparation of stable acidic baths with high content of tellurium, and with the addition of citrate acid. In order to analyse the mechanism of the process of tellurium deposition, the electroanalytical tests were conducted. The tests of cyclic voltammetry and hydrodynamic ones were performed with the use of polycrystalline gold disk electrode. The range of potentials in which deposition of tellurium in direct four-electron process is possible was determined as well as the reduction of deposited Te° to Te{sup 2−} and its re-deposition as a result of the comproportionation reaction. On the basis of the obtained results, the deposition of tellurium was conducted by the potentiostatic method. The influence of a deposition potential and a concentration of TeO{sub 2} in the solution on the rate of tellurium coatings deposition was examined. The presence of tellurium was confirmed by X-ray spectrofluorometry and electron probe microanalysis. In order to determine the phase composition and the morphology, the obtained coatings were analysed with the use of x-ray diffraction and scanning electron microscopy.

Properties of low-alloy steel with tellurium

International Nuclear Information System (INIS)

Popova, L.V.; Lebedev, D.V.; Litvinenko, D.A.; Nasibov, A.G.

1983-01-01

The results of investigations into 09G2 and 09G2F steels alloyed with tellurium after controlled rolling are presented. 0.002-0.011% tellurium additions did not change strength and plastic properties of the steels after controlled rolling. Tellurium additions results in 40-50% increase of the steel impact strength on samples With circular and sharp cuts in brittle-viscous region. 0.002-0.003% of tellurium is considered to be the optimum content from the view point of increa=. sing steel strength. Increase of impact strength takes place at the expense of growth of both work function of crack formation and work function of crack propagation but in different temperature ranges: at the expense of firstone at 80-40 deg C, at the expense of second one at 20-40 deg C. 0.002-0.011% teilurium additions mainly at the expense of sulphide globularization bring about decrease of anisotropy of steet properties by impact strength reducing anisotropy factor from 2 to 1.5

Analysis of tellurium-silicon alloys. Part 1. Determination of tellurium by the reduction from perchloric acid solution

International Nuclear Information System (INIS)

Teperek, J.

1977-01-01

When 100-150 mg of tellurium is dissolved in the solution containing 20 cm 3 72 wt.% of perchloric acid, the reduction of tellurium to elementary form is possible only after adding 60-100 milimoles of HCl. The reduction is performed by adding 1 cm 3 of saturated sodium pyrosulphite solution (Na 2 S 2 O 5 ) and 10 cm 3 of 10 wt.% hydrazine hydrochloride solution (N 2 H 4 .2HCl) to 80-90 cm 3 of cold solution of Te in HClO 4 -HCl mixture. The reduction is completed after 3-5 min. of boiling. When 150-200 mg sample of Te-Si alloy is dissolved in 20 cm 3 of hot 72% per chloric acid, the separation of components is reached. Tellurium can be determinated in filtrate by proposed procedure with high accuracy and precision. (author)

Polarographic determination of selenium and tellurium in silver-gold alloys

International Nuclear Information System (INIS)

Gornostaeva, T.D.; Shmargun, S.V.

1986-01-01

The determination of selenium and tellurium is of importance in monitoring the composition of silver-gold alloys (SGA) since these elements are harmful impurities in the pure metals. Tellurium is determined in silver alloys by atomic absorption and atomic emmission methods; selenium determination is made by atomic absorption methods. This paper examines the polarographic determination of silver and tellurium in SGA containing platinum metals and copper. Copper and the bulk of the platinum and palladium were removed by precipitating selenium and tellurium with potassium hypophosphite in the elementary state from 6 M HC1. The results of an analysis of samples of SGA according to the proposed method were compared with the results obtained by the atomic absorption method. the relative deviation in the determination of 0.02-1.0% by weight selenium and tellurium does not exceed 0.12 (n = 5)

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

Energy Technology Data Exchange (ETDEWEB)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of); Shakibaie, Mojtaba [Department of Pharmacognosy and Biotechnology, School of Pharmacy, Pharmaceutics Research Center, Kerman University of Medical Sciences, P.O. Box 76175-493 Kerman (Iran, Islamic Republic of); Rezaie, Sassan [Department of Medical Biotechnology, School of Advanced Medical Technologies, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Shahverdi, Ahmad Reza, E-mail: shahverd@sina.tums.ac.ir [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of)

2012-11-15

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

International Nuclear Information System (INIS)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham; Shakibaie, Mojtaba; Rezaie, Sassan; Shahverdi, Ahmad Reza

2012-01-01

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Structure and activity of tellurium-cerium oxide acrylonitrile catalysts

International Nuclear Information System (INIS)

Bart, J.C.J.; Giordano, N.

1982-01-01

Ammoxidation of propylene to acrylonitrile (ACN) was investigated over various silica-supported (Te,Ce)O catalysts at 360 and 440 0 C. The binary oxide system used consists of a single nonstoichiometric fluorite-type phase α-(Ce,Te)O 2 up to about 80 mole% TeO 2 and a tellurium-saturated solid solution β-(Ce,Te)O 2 at higher tellurium concentrations. The ACN yield varies almost linearly with the tellurium content of (Ce,Te)O 2 . The β-(Ce,Te)O 2 phase is the most active component of the system (propylene conversion and ACN selectivity at 440 C of 76.7 and 74%, respectively) and is slightly more selective to ACN than α-Te0 2 . Tellurium reduces the overoxidation properties of cerium and selective oxidation occurs through Te(IV)-bonded oxygen

A recycling model of the biokinetics of systemic tellurium.

Science.gov (United States)

Giussani, Augusto

2014-11-01

To develop a compartmental model of the systemic biokinetics of tellurium required for calculating the internal dose and interpreting bioassay measurements after incorporation of radioactive tellurium. The compartmental model for tellurium was developed with the software SAAM II v. 2.0 (©The Epsilon Group, Charlottesville, Virginia, USA). Model parameters were determined on the basis of published retention and excretion data in humans and animals. The model consists of two blood compartments, one compartment each for liver, kidneys, thyroid, four compartments for bone tissues and a generic compartment for the soft tissues. The model predicts a rapid urinary excretion of systemic tellurium: 45% in the first 24 h and 84% after 50 d. Faecal excretion amounts to 0.4% after 3 d and 9% after 50 d. Whole body retention is 55% after one day, and 2.8% after 100 d. These values as well as the retained fractions in the single organs are reasonably consistent with the available human and animal data (studies with swine and guinea pigs). The proposed model gives a realistic description of the available biokinetic data for tellurium and will be adopted by the International Commission on Radiological Protection for applications in internal dosimetry.

Atomic absorption determination of ultratrace tellurium in rocks utilizing high sensitivity sampling systems

International Nuclear Information System (INIS)

Beaty, R.D.

1973-01-01

The sampling boat and the graphite furnace were shown to possess the required sensitivity to detect tellurium at ultratrace levels, in a variety of sample types, by atomic absorption. In the sampling boat approach, tellurium in sample solutions is chemically separated and concentrated by extraction into methyl isobutyl ketone before measurement. For samples exhibiting extraction interferences or excessively high background absorption, a preliminary separation of tellurium by coprecipitation with selenium is described. Using this technique, tellurium can be quantitatively detected down to 5 nanograms and linear response is observed to 100 nanograms. Relative standard deviations of better than 7 percent are achieved for 50 nanograms of tellurium. For samples that have a tellurium content below the detection limits of the sampling boat, the graphite furnace is used for atomization. By this method, as little as 0.07 nanograms of tellurium can be detected, and a precision of 1 percent relative standard deviation is achievable at the 5 nanogram level. A routinely applicable procedure was developed for determining tellurium in rocks, using the graphite furnace, after a hydrofluoric acid decomposition of the sample. Using this procedure, tellurium data were obtained on 20 different rocks, and the significance of this new information is discussed. (Diss. Abstr. Int., B)

METHODS OF SYNTHESIS EIGHT-TELLURIUM-CONTAINING HETEROCYCLES WITH MORE HETEROATOMS

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2013-01-01

Full Text Available In this article systematized and summarized data on the synthesis of neweight-embered tellurium-containing heterocycles and new preparative methods described above produce heterocyclic tellurium.

Inclusion free cadmium zinc tellurium and cadmium tellurium crystals and associated growth method

Science.gov (United States)

Bolotnikov, Aleskey E [South Setauket, NY; James, Ralph B [Ridge, NY

2010-07-20

The present disclosure provides systems and methods for crystal growth of cadmium zinc tellurium (CZT) and cadmium tellurium (CdTe) crystals with an inverted growth reactor chamber. The inverted growth reactor chamber enables growth of single, large, high purity CZT and CdTe crystals that can be used, for example, in X-ray and gamma detection, substrates for infrared detectors, or the like. The inverted growth reactor chamber enables reductions in the presence of Te inclusions, which are recognized as an important limiting factor in using CZT or CdTe as radiation detectors. The inverted growth reactor chamber can be utilized with existing crystal growth techniques such as the Bridgman crystal growth mechanism and the like. In an exemplary embodiment, the inverted growth reactor chamber is a U-shaped ampoule.

Selenium and tellurium reagents in organic synthesis

International Nuclear Information System (INIS)

Comasseto, J.V.

1984-01-01

A review of the contribution of the University of Sao Paulo (SP, Brazil) to the organic synthesis of selenium and tellurium reagents is made. Major reactions amoung selenium compounds and insaturated substrates, phosphorus, ester enolates as well as the use of phase transference catalysed reactions to produce arylselenolate are described. For tellurium, interactions of its compounds with organic substrates and reactive intermediates (e.g. benzino diazomethane) are reported. (C.L.B.) [pt

Electrophilic addition of selenium and tellurium halides to methyldiethynylsilane

International Nuclear Information System (INIS)

Amosova, S.V.; Penzik, M.V.; Martynov, A.V.; Zhilitskaya, L.V.; Voronkov, M.G.

2009-01-01

Reaction of TeCl 4 with methyldiethynylsilane (MDES) proceeds with the predominant formation of E-isomer 1,1,3,6-tetrachlorine-1-methyl-1-(methyldiethynylsiloxy)-1,4-tellurium(IV) silafulvic due to the interaction of intermediate E-isomer 4-methyl-1,1,3,6-tetrachlorine-1,4-tellurium(IV)silafulvic with MDES. TeCl 4 Reacts with MDES without reduction of Te(IV) in Te(II). Tetracoordination of tellurium atom in heterocycle was established by NMR 125 Te. Mass spectrum of heterocycle shows the presence of fragmentary ions [M-Cl 2 ] + . According elemental analysis Te:Cl=1:4 ratio proves composition of heterocycle

Solvent Extraction of Tellurium from Chloride Solutions Using Tri-n-butyl Phosphate: Conditions and Thermodynamic Data

Directory of Open Access Journals (Sweden)

Dongchan Li

2014-01-01

Full Text Available The extractive separation of tellurium (IV from hydrochloric acid media with tri-n-butyl phosphate (TBP in kerosene was investigated. The dependence on the extraction of tellurium species, concentrations of tellurium and TBP, extraction time and stage, organic/aqueous ratio, and interferences from coexist metallic ions were examined and are discussed. Besides, the stripping agent and stripping time were also studied. It was found that the extraction reaction corresponds to the neutral complex formation mechanism and the extracted species is TeCl4·3TBP and that the extraction process is exothermic. The thermodynamic parameters of enthalpy ΔH, entropy ΔS, and free energy ΔG of the extraction process were evaluated at −26.2 kJ·mol−1, −65.6 J·mol−1·K−1, and −7.0 kJ·mol−1, respectively at 293 K.

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis

Directory of Open Access Journals (Sweden)

Yang F

2014-10-01

Full Text Available Fang Yang,1 Ka-Hing Wong,2 Yufeng Yang,3 Xiaoling Li,1 Jie Jiang,1 Wenjie Zheng,1 Hualian Wu,1 Tianfeng Chen1 1Department of Chemistry, Jinan University, Guangzhou, People’s Republic of China; 2Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hong Kong, People’s Republic of China; 3Institute of Hydrobiology, College of Life Science and Technology, Jinan University, Guangzhou, People’s Republic of China Abstract: Tellurium-containing phycocyanin (Te-PC and allophycocyanin (Te-APC, two organic tellurium (Te species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 µg g-1 protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropanedihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress. Keywords: tellurium, phycocyanin, allophycocyanin, purification, antioxidant activity

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis.

Science.gov (United States)

Yang, Fang; Wong, Ka-Hing; Yang, Yufeng; Li, Xiaoling; Jiang, Jie; Zheng, Wenjie; Wu, Hualian; Chen, Tianfeng

2014-01-01

Tellurium-containing phycocyanin (Te-PC) and allophycocyanin (Te-APC), two organic tellurium (Te) species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 μg g(-1) protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropane)dihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress.

Flame and flameless atomic-absorption determination of tellurium in geological materials

Science.gov (United States)

Chao, T.T.; Sanzolone, R.F.; Hubert, A.E.

1978-01-01

The sample is digested with a solution of hydrobromic acid and bromine and the excess of bromine is expelled. After dilution of the solution to approximately 3 M in hydrobromic acid, ascorbic acid is added to reduce iron(III) before extraction of tellurium into methyl isobutyl ketone (MIBK). An oxidizing air-acetylene flame is used to determine tellurium in the 0.1-20 ppm range. For samples containing 4-200 ppb of tellurium, a carbon-rod atomizer is used after the MIBK extract has been washed with 0.5 M hydrobromic acid to remove the residual iron. The flame procedure is useful for rapid preliminary monitoring, and the flameless procedure can determine tellurium at very low concentrations. ?? 1978.

Study of distribution coefficients of admixtures in tellurium

International Nuclear Information System (INIS)

Kuchar, L.; Drapala, J.; Kuchar, L. jr.

1986-01-01

Limit areas of tellurium-admixture binary systems were studied and the values determined of steady-state distribution coefficients of admixtures. A second order polynomial was used to express equations of solidus and liquidus curves for Te-Se, Te-S, Te-Hg systems; the curves are graphically represented. The most effective method for preparing high-purity tellurium is zonal melting with material removal. (M.D.). 4 figs., 4 tabs., 16 refs

Organotellurium ligands – designing and complexation reactions

Indian Academy of Sciences (India)

Unknown

membered rings it is negative and ~30 ppm only. Keywords. Organotellurium ligands; hybrid telluroether; platinum metal complexes; tellurium-125 NMR. 1. Introduction. Tellurium is the noblest metalloid which may act as a Lewis acid as well as Lewis base. The ligand chemistry of tellurium, which acts as a 'soft' donor, was ...

Effects of tellurium concentration on the structure of melt-grown ZnSe crystals

International Nuclear Information System (INIS)

Atroshchenko, Lyubov V.; Galkin, Sergey N.; Rybalka, Irina A.; Voronkin, Evgeniy F.; Lalayants, Alexandr I.; Ryzhikov, Vladimir D.; Fedorov, Alexandr G.

2005-01-01

It has been shown that isovalent doping by tellurium positively affects the structural perfection of ZnSe crystals related to the completeness of the wurtzite-sphalerite phase transition. The optimum concentration range of tellurium in ZnSe crystals is 0.3-0.6 mass %. X-ray diffraction studies have shown that in ZnSe 1-x Te x crystals at tellurium concentrations below 0.3 mass % twinning and packing defects occur, while tellurium concentrations above 0.6 mass % lead to formation of tetragonal crystal lattice

Large-scale synthesis of Tellurium nanostructures via galvanic displacement of metals

Science.gov (United States)

Kok, Kuan-Ying; Choo, Thye-Foo; Ubaidah Saidin, Nur; Rahman, Che Zuraini Che Ab

2018-01-01

Tellurium (Te) is an attractive semiconductor material for a wide range of applications in various functional devices including, radiation dosimeters, optical storage materials, thermoelectric or piezoelectric generators. In this work, large scale synthesis of tellurium (Te) nanostructures have been successfully carried out in different concentrations of aqueous solutions containing TeO2 and NaOH, by galvanic displacements of Zn and Al which served as the sacrificial materials. Galvanic displacement process is cost-effective and it requires no template or surfactant for the synthesis of nanostructures. By varying the concentrations of TeO2 and NaOH, etching temperatures and etching times, Te nanostructures of various forms of nanostructures were successfully obtained, ranging from one-dimensional needles and rod-like structures to more complex hierarchical structures. Microscopy examinations on the nanostructures obtained have shown that both the diameters and lengths of the Te nanostructures increased with increasing etching temperature and etching time.

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2003-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122 Te, 124 Te, 125 Te, 126 Te, 128 Te, and 130 Te are reported. These values are based on a combination of newly determined partial γ-ray cross sections obtained from experiments on targets contained natural Te and γ intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

Energy Technology Data Exchange (ETDEWEB)

Tomandl, I.; Honzatko, J.; von Egidy, T.; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-03-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given.

Van der Waals epitaxy and photoresponse of hexagonal tellurium nanoplates on flexible mica sheets.

Science.gov (United States)

Wang, Qisheng; Safdar, Muhammad; Xu, Kai; Mirza, Misbah; Wang, Zhenxing; He, Jun

2014-07-22

Van der Waals epitaxy (vdWE) is of great interest due to its extensive applications in the synthesis of ultrathin two-dimensional (2D) layered materials. However, vdWE of nonlayered functional materials is still not very well documented. Here, although tellurium has a strong tendency to grow into one-dimensional nanoarchitecture due to its chain-like structure, we successfully realize 2D hexagonal tellurium nanoplates on flexible mica sheets via vdWE. Chemically inert mica surface is found to be crucial for the lateral growth of hexagonal tellurium nanoplates since it (1) facilitates the migration of tellurium adatoms along mica surface and (2) allows a large lattice mismatch. Furthermore, 2D tellurium hexagonal nanoplates-based photodetectors are in situ fabricated on flexible mica sheets. Efficient photoresponse is obtained even after bending the device for 100 times, indicating 2D tellurium hexagonal nanoplates-based photodetectors on mica sheets have a great application potential in flexible and wearable optoelectronic devices. We believe the fundamental understanding of vdWE effect on the growth of 2D tellurium hexagonal nanoplate can pave the way toward leveraging vdWE as a useful channel to realize the 2D geometry of other nonlayered materials.

Investigation of γ-irradiation influence on the DLTS spectra in silicon diluted by tellurium

International Nuclear Information System (INIS)

Sultanov, N.A.; Tadzhibaev, M.; Mirzabadalov, Zh

1997-01-01

The influence of gamma-radiation on deep level transient spectroscopy(DLTS) spectra for silicon crystals doped with tellurium was studied. The DLTS spectra have shown that tellurium in silicon formed two deep levels with fixed ionization energy. It was shown that the presence of tellurium prevents the formation of radiation defects

Status of tellurium--hastelloy N studies in molten fluoride salts

International Nuclear Information System (INIS)

Keiser, J.R.

1977-10-01

Tellurium, which is a fission product in nuclear reactor fuels, can embrittle the surface grain boundaries of nickel-base structural materials. This report summarizes results of an experimental investigation conducted to understand the mechanism and to develop a means of controlling this embrittlement in the alloy Hastelloy N. The addition of a chromium telluride to salt can be used to provide small partial pressures of tellurium simulating a reactor environment where tellurium appears as a fission product. The intergranular embrittlement produced in Hastelloy N when exposed to this chromium telluride-salt mixture can be reduced by adding niobium to the Hastelloy N or by controlling the oxidation potential of the salt in the reducing range

Comparison between selenium and tellurium clusters

International Nuclear Information System (INIS)

Benamar, A.; Rayane, D.; Tribollet, B.; Broyer, M.; Melinon, P.

1991-01-01

Selenium and tellurium clusters are produced by the inert gas condensation technique. The mass spectra of both species are completely different and reveal different properties. In selenium, a periodicity of 6-7 is observed and may be interpreted by the binding energy between small cyclic molecules. Moreover, it was very difficult to obtained large clusters probably because the binding energy between these molecules is very small. In tellurium, these periodic structures do not exist and large clusters are easily obtained in nucleation conditions where only small selenium clusters are present. These results are discussed and a simple nucleation model is used to illustrate this different behavior. Finally these clusters properties are correlated to the bulk structure of both materials. (orig.)

Electrodeposition of antimony, tellurium and their alloys from molten acetamide mixtures

NARCIS (Netherlands)

Nguyen, H.P.; Peng, X.; Murugan, G.; Vullers, R.J.M.; Vereecken, P.M.; Fransaer, J.

2013-01-01

We examine the electrodeposition of antimony (Sb), tellurium (Te) and their alloys from molten mixtures of acetamide - antimony chloride and tellurium chloride. The binary mixtures of acetamide with SbCl3 and TeCl 4 exhibit eutectic formation with large depressions of freezing points to below room

Neutron activation analysis of high purity tellurium

International Nuclear Information System (INIS)

Gil'bert, Eh.N.; Verevkin, G.V.; Obrazovskij, E.G.; Shatskaya, S.S.

1980-01-01

A scheme of neutron activation analysis of high purity tellurium is developed. Weighed amount of Te (0.5 g) is irradiated for 20-40 hr in the flux of 2x10 13 neutron/(cm 2 xs). After decomposition of the sample impurities of gold and palladium are determined by the extraction with organic sulphides. Tellurium separation from the remaining impurities is carried out by the extraction with monothiobenzoic acid from weakly acidic HCl solutions in the presence of iodide-ions, suppressing silver extraction. Remaining impurity elements in the refined product are determined γ-spectrometrically. The method allows to determine 34 impurities with determination limits 10 -6 -10 -11 g

DETECTION OF THE SECOND r-PROCESS PEAK ELEMENT TELLURIUM IN METAL-POOR STARS ,

International Nuclear Information System (INIS)

Roederer, Ian U.; Lawler, James E.; Cowan, John J.; Beers, Timothy C.; Frebel, Anna; Ivans, Inese I.; Schatz, Hendrik; Sobeck, Jennifer S.; Sneden, Christopher

2012-01-01

Using near-ultraviolet spectra obtained with the Space Telescope Imaging Spectrograph on board the Hubble Space Telescope, we detect neutral tellurium in three metal-poor stars enriched by products of r-process nucleosynthesis, BD +17 3248, HD 108317, and HD 128279. Tellurium (Te, Z = 52) is found at the second r-process peak (A ≈ 130) associated with the N = 82 neutron shell closure, and it has not been detected previously in Galactic halo stars. The derived tellurium abundances match the scaled solar system r-process distribution within the uncertainties, confirming the predicted second peak r-process residuals. These results suggest that tellurium is predominantly produced in the main component of the r-process, along with the rare earth elements.

Review of tellurium release rates from LWR fuel elements under accident conditions

International Nuclear Information System (INIS)

Lorenz, R.A.; Beahm, E.C.; Wichner, R.P.

1983-01-01

Although fission product tellurium presents a potentially significant radiohazard, its release and transport in source-term experiments is frequently overlooked because it does not possess a readily measurable, gamma emission; moreover, a recent study emphasized noble gas, iodine and cesium release from LWR fuel elements because of the large data base that exists for these materials. Some new tests show that in some cases tellurium may be held up in core material to a greater degree than previously assumed - an observation that prompts a careful reappraisal of the existing tellurium-release data and its chemical foundation

Methods of selenium and tellurium determination in geological and enviromental materials

International Nuclear Information System (INIS)

Nazarenko, I.I.; Kislova, I.V.

1988-01-01

Atomic-absorption and atomic-emission methods of tellurium determination in ores and products of their processing are described. Flame variant with extractional concentration permits to determine tellurium with the concentration up to 6x10 -6 %, the use of graphite cuvette after preliminary concentration-up to 1x10 -6 %. Atomic-emissional method permits to determine 3x10 -4 % Te from sample of 0.5 g

Selenium and tellurium as carbon substitutes

International Nuclear Information System (INIS)

Knapp, F.F. Jr.

1980-01-01

This review has summarized structure-activity studies with 75 Se- and /sup 123m/Te-labeled radiopharmaceuticals in which the selenium or tellurium heteroatom has been inserted between carbon-carbon bonds. The agents that have been investigated in most detail include steroids for adrenal imaging and long-chain fatty acids, and a variety of other unique agents have also been studied. Because of the great versatility of the organic chemistry of selenium and tellurium, there is continuing interest in the preparation of radiopharmaceuticals labeled with 75 Se, 73 Se, and /sup 123m/Te. There are two important factors which will determine the extent of future interest in such agents. These include the necessity of a decrease in the cost of highly enriched 122 Te to make the reactor production of /sup 123m/Te cost effective. In addition, the potential preparation of large amounts of 73 Se should stimulate the development of 73 Se-labeled radiopharmaceuticals

Investigation of biomethylation of arsenic and tellurium during composting

International Nuclear Information System (INIS)

Diaz-Bone, Roland A.; Raabe, Maren; Awissus, Simone; Keuter, Bianca; Menzel, Bernd; Kueppers, Klaus; Widmann, Renatus; Hirner, Alfred V.

2011-01-01

Though the process of composting features a high microbiological activity, its potential to methylate metals and metalloids has been little investigated so far in spite of the high impact of this process on metal(loid) toxicity and mobility. Here, we studied the biotransformation of arsenic, tellurium, antimony, tin and germanium during composting. Time resolved investigation revealed a highly dynamic process during self-heated composting with markedly differing time patterns for arsenic and tellurium species. Extraordinary high concentrations of up to 150 mg kg -1 methylated arsenic species as well as conversion rates up to 50% for arsenic and 5% for tellurium were observed. In contrast, little to no conversion was observed for antimony, tin and germanium. In addition to experiments with metal(loid) salts, composting of arsenic hyperaccumulating ferns Pteris vittata and P. cretica grown on As-amended soils was studied. Arsenic accumulated in the fronds was efficiently methylated resulting in up to 8 mg kg -1 methylated arsenic species. Overall, these studies indicate that metal(loid)s can undergo intensive biomethylation during composting. Due to the high mobility of methylated species this process needs to be considered in organic waste treatment of metal(loid) contaminated waste materials.

Determining arsenic in elemental antimony containing selenium and tellurium

International Nuclear Information System (INIS)

Mogileva, M.G.; Kozlova, E.L.

1986-01-01

The authors have developed a method of determining arsenic in metallic antimony containing selenium, tellurium, and mercury, in which they isolated it in elementary form for separation from the antimony and the associated elements (silicon and phosphorus), followed by colorimetric determination of the arsenic from arsenic-molbdenum blue. The reducing agents to reduce the arsenic were sodium hypophosphite and tin(II) chloride, which do not reduce antimony and which do not interfere with the determination. This method of determining arsenic in metallic antimony without preliminary separation of the selenium and tellurium is in no way inferior in accuracy to the method given in All-Union State Standard (GOST) 1367.4-83

Release of tellurium and cesium from UO2 in LWR fuel rods during irradiation

International Nuclear Information System (INIS)

Malen, K.A.

1983-01-01

In this paper the release of tellurium (Te-132) and cesium (Cs-134 and Cs-137) from UO 2 -fuel is analyzed. The basis for the analysis is the experimental results from the S176 series of experiments performed at Studsvik. It seems that the model developed earlier for release of iodine applies also to tellurium and cesium. This model assumes sweeping up of the species in question by moving grain boundaries and subsequent release through grain boundary porosity. An interesting extra feature is deposition of tellurium at temperatures in the range 1500-2000 K believed to be due to condensation. (author)

METALCOMPLEXES OF TELLURIUM-CONTAINING AMINES AND AZOMETINES

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2014-01-01

Full Text Available In this article methods of synthesis and reactionary ability of metalcomplexes of tellurium-containing amines, azometines, of a problem of competitive coordination with use of the principle of "soft" and "rigid" acids and the bases (R. Pearson.

The characterisation of vapour-phase alkali metal-tellurium-oxygen species

International Nuclear Information System (INIS)

Gomme, R.A.; Ogden, J.S.; Bowsher, B.R.

1986-10-01

Detailed assessments of hypothetical severe accidents in light water reactors require the identification of the chemical forms of the radionuclides in order to determine their transport characteristics. Caesium and tellurium are important volatile fission products in accident scenarios. This report describes detailed studies to characterise the chemical species that vaporise from heated mixtures of various alkali metal-tellurium-oxygen systems. The molecular species were characterised by a combination of quadrupole mass spectrometry and matrix isolation-infrared spectroscopy undertaken in conjunction with experiments involving oxygen-18 substitution. The resulting spectra were interpreted in terms of a vapour-phase molecule with the stoichiometry M 2 TeO 3 (M = K,Rb,Cs) for M/Te molecular ratios of ∼ 2, and polymeric species for ratios < 2. This work has demonstrated the stability of caesium tellurite. The formation of this relatively low-volatility, water-soluble species could significantly modify the transport and release of caesium and tellurium. The data presented in this report should allow more comprehensive thermodynamic calculations to be undertaken that assist in the quantification of fission product behaviour during severe reactor accidents. (author)

Double beta decay of tellurium-130

International Nuclear Information System (INIS)

Richardson, J.F.; Manuel, O.K.; Sinha, B.; Thorpe, R.I.

1986-01-01

The isotopic composition of xenon is reported in four, neutron-irradiated tellurium minerals - tellurobismuthite from Boliden, Sweden, native tellurium from the Good Hope Mine of Gunnison County, Colorado, altaite from the Kirkland Lake area, Ontario, and altaite from the Mattagami Lake area, Quebec. From the amount of radiogenic 130 Xe and pile-produced 131 Xe in these samples, it is concluded that the half-life of 130 Te for ββ-decay is 21 y based on measured values of (1.0+-0.3) . 10 21 y and higher. Our results demonstrate that there has been no significant partial leakage of radiogenic 130 Xe from these minerals over geologic time. Larger values of Tsub(1/2), as indicated from some of the analysis reported here and in other studies, are attributed to recrystallization of the soft telluride minerals and complete resetting of the Te-Xe system after mineralization. The value obtained here for the half-life of 130 Te is substantiated by recent measurements on xenon in tellurides from Kalgoorlie, Western Australia. (orig.)

RILIS-ionized mercury and tellurium beams at ISOLDE CERN

Energy Technology Data Exchange (ETDEWEB)

Day Goodacre, T., E-mail: thomas.day.goodacre@cern.ch [CERN (Switzerland); Billowes, J. [The University of Manchester, School of Physics and Astronomy (United Kingdom); Chrysalidis, K. [CERN (Switzerland); Fedorov, D. V. [Petersburg Nuclear Physics Institute (Russian Federation); Fedosseev, V. N.; Marsh, B. A. [CERN (Switzerland); Molkanov, P. L. [Petersburg Nuclear Physics Institute (Russian Federation); Rossel, R. E.; Rothe, S.; Seiffert, C. [CERN (Switzerland); Wendt, K. D. A. [Johannes Gutenberg Universität, Institut für Physik (Germany)

2017-11-15

This paper presents the results of ionization scheme development for application at the ISOLDE Resonance Ionization Laser Ion Source (RILIS). Two new ionization schemes for mercury are presented: a three-step three-resonance ionization scheme, ionizing via an excitation to a Rydberg level and a three-step two-resonance ionization scheme, with a non-resonant final step to the ionization continuum that corresponded to a factor of four higher ionization efficiency. The efficiency of the optimal mercury ionization scheme was measured, together with the efficiency of a new three-step three resonance ionization scheme for tellurium. The efficiencies of the mercury and tellurium ionization schemes were determined to be 6 % and >18 % respectively.

Nano-Structured Crystalline Te Films by Laser Gas-Phase Pyrolysis of Dimethyl Tellurium

Czech Academy of Sciences Publication Activity Database

Pola, Josef; Pokorná, Veronika; Boháček, Jaroslav; Bastl, Zdeněk; Ouchi, A.

2004-01-01

Roč. 71, č. 2 (2004), s. 739-746 ISSN 0165-2370 R&D Projects: GA AV ČR IAA4072107; GA MŠk OC 523.60 Institutional research plan: CEZ:AV0Z4072921; CEZ:AV0Z4032918; CEZ:AV0Z4040901 Keywords : dimethyl tellurium * tellurium films * laser Subject RIV: CA - Inorganic Chemistry Impact factor: 1.352, year: 2004

Thermoelectric properties of electrodeposited tellurium films and the sodium lignosulfonate effect

International Nuclear Information System (INIS)

Abad, Begoña; Rull-Bravo, Marta; Hodson, Stephen L.; Xu, Xianfan; Martin-Gonzalez, Marisol

2015-01-01

The effect of the addition of a surfactant, sodium lignosulfonate (SLS), on the thermoelectric properties of tellurium films prepared by electrochemical deposition is studied. The growth mechanism is found to have an important role in the thermoelectric properties since the grain size of the films is sharply reduced when the surfactant is added to the solution. For this reason, the electrical resistivity of the tellurium films when the surfactant is not added is 229 μΩ·m, which is lower than 798 μΩ·m with SLS. The Seebeck coefficient values are not influenced, with values in the vicinity of 285 μV/K for both solutions. The power factor resulted higher values than previous works, reaching values of 280 μW/m·K 2 (without SLS) and 82 μW/m·K 2 (with SLS) at room temperature. Finally, the thermal conductivity was measured by means of the Photoacoustic technique, which showed values of the order of 1 W/m·K for both solutions, which is a factor of 3 less than the bulk value of tellurium. A notable observation is that the power factor and the thermal conductivity of electrodeposited tellurium films have the same order of magnitude of bismuth telluride films grown by electrodeposition. The figure of merit is estimated to be approximately one order of magnitude higher than the bulk value, 0.09 without SLS and 0.03 with SLS, both at room temperature

Influence of ion beam irradiation induced defects on the structural, optical and electrical properties of tellurium nanowires

Energy Technology Data Exchange (ETDEWEB)

Kumar, Narinder [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Department of Physics, Haryana College of Technology & Management, Kaithal, 136027 (India); Kumar, Rajesh [Department of Physics, RN College of Engineering & Technology, Madlauda, 132104 (India); Kumar, Sushil, E-mail: sushil_phys@rediffmail.com [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Chakarvarti, S.K. [Research and Development, Manav Rachana International University, Faridabad, 121001 (India)

2016-11-01

In this study, tellurium nanowires were electrodeposited into the polymer membranes from aqueous acidic bath containing HTeO{sub 2}{sup +} ions. The field emission scanning electron microscopy (FESEM) images confirmed the formation of uniform and straight nanowires. The influence of 110 MeV Ni{sup 8+} ion irradiation induced defects on the structural, optical and electrical properties of as–deposited tellurium nanowires were examined using X-ray diffraction (XRD), UV–visible absorption spectroscopy and current–voltage (I–V) measurements. The XRD data depicted the hexagonal phase of tellurium nanowires and further revealed a variation in the intensity of diffraction peaks of ion irradiated nanowires. Williamson–Hall (WH) analysis is used for convoluting the size and microstrain contributions to the width of diffraction peaks. Tellurium nanowires exhibited a distinct absorbance band in the visible region at 686 nm, while this was absent in bulk tellurium. Electrical properties of nanowires are explored on the basis of I–V curves, which revealed a significant increase in the electrical conductivity of irradiated nanowires. A possible mechanism for the enhanced electrical conductivity is the increase in carrier concentration due to thermally excited defects. The defects produced by ion irradiation play a vital role in modifying the properties of semiconducting nanowires. - Highlights: • 110 MeV Ni{sup 8+} ion beam induced changes in tellurium nanowires have been examined. • Nanowires were prepared using template electrodeposition method. • Irradiation improved the electrical conductivity of tellurium nanowires. • Mechanism for enhanced electrical conductivity of irradiated nanowires was discussed.

Kinetics and mechanism of oxidation of tellurium (IV) by periodate in alkaline medium

International Nuclear Information System (INIS)

Srinivas, K.; Vani, P.; Dikshitulu, L.S.A.

1995-01-01

Detailed kinetic study of the oxidation of tellurium (IV) by periodate in alkaline medium has been carried out to compare the mechanisms of oxidation in the acid and alkaline media. It is interesting to note that the rate step involves a two-electron transfer from tellurium (IV) to periodate in alkaline medium although the kinetic pattern is somewhat different from that in the acid medium. 7 refs., 1 tab

Chemical Process for Treatment of Tellurium and Chromium Liquid Waste from I-131 Radioisotope Production

International Nuclear Information System (INIS)

Zainus-Salimin; Gunandjar; Dedy-Harsono; Hendro; Sugeng-Purnomo; Mohammad-Faruq; Zulfakhri

2000-01-01

The I-131 radioisotope is used in nuclear medicine for diagnosis and therapy. The I-131 radioisotope is produced by wet distillation at Bandung Nuclear Research Center and generated about 4,875 Itr of liquid waste containing 2,532.8 ppm of tellurium and 1,451.8 ppm chromium at pH 1. Considering its negative impact to the environment caused by toxic behaviour of tellurium and chromium, it is necessary to treat chemically that's liquid waste. The research of chemical treatment of tellurium and chromium liquid waste from I-131 radioisotope production has been done. The steps of process are involved of neutralisation with NaOH, coagulation-flocculation process for step I using Ca(OH) 2 coagulant for precipitation of sulphate, sulphite, oxalic, chrome Cr 3+ , and coagulation-flocculation process for step II using BaCI 2 coagulant for precipitation of chrome Cr 6+ and tellurium from the supernatant of coagulation in step I. The best result of experiment was achieved at 0.0161 ppm of chromium concentration on the supernatant from coagulation-flocculation of step I using 3.5 g Ca(OH) 2 for 100 ml of liquid waste, and 0.95 ppm of tellurium concentration on the final supernatant from coagulation-flocculation by of step II using 0.7 g BaCI 2 for supernatant from coagulation of step I. (author)

Enhancement of Au-Ag-Te contents in tellurium-bearing ore minerals via bioleaching

Science.gov (United States)

Choi, Nag-Choul; Cho, Kang Hee; Kim, Bong Ju; Lee, Soonjae; Park, Cheon Young

2018-03-01

The purpose of this study was to enhance the content of valuable metals, such as Au, Ag, and Te, in tellurium-bearing minerals via bioleaching. The ore samples composed of invisible Au and Au paragenesis minerals (such as pyrite, chalcopyrite, sphalerite and galena) in combination with tellurium-bearing minerals (hessite, sylvanite and Tellurobismuthite) were studied. Indigenous microbes from mine drainage were isolated and identified as Acidithiobacillus ferrooxidans, which were used in bioleaching after adaption to copper. The effect of the microbial adaption on the bioleaching performance was then compared with the results produced by the non-adaptive process. The microbial adaption enhanced the Au-Ag-Te contents in biological leaching of tellurium-bearing ore minerals. This suggests that bioleaching with adapted microbes can be used both as a pretreatment and in the main recovery processes of valuable metals.

Rutherford backscatter measurements on tellurium and cadmium implanted gallium arsenide

International Nuclear Information System (INIS)

Bell, E.C.

1979-10-01

The primary aim of the work described in this thesis was to examine implanted layers of the dopant impurities cadmium and tellurium in gallium arsenide and to experimentally assess their potential for producing electrically active layers. 1.5 MeV Rutherford backscattering measurements of lattice disorder and atom site location have been used to assess post implantation thermal annealing and elevated temperature implantations to site the dopant impurities on either gallium or arsenic lattice positions in an otherwise undisordered lattice. Pyrolitically deposited silicon dioxide was used as an encapsulant to prevent thermal dissociation of the gallium arsenide during annealing. It has been shown that high doses of cadmium and tellurium can be implanted without forming amorphous lattice disorder by heating the gallium arsenide during implantation to relatively low temperatures. Atom site location measurements have shown that a large fraction of a tellurium dose implanted at 180 0 C is located on or near lattice sites. Channeled backscatter measurements have shown that there is residual disorder or lattice strain in gallium arsenide implanted at elevated temperatures. The extent of this disorder has been shown to depend on the implanted dose and implantation temperature. The channeling effect has been used to measure annealing of the disorder. (author)

Phenylethynyl-butyltellurium inhibits the sulfhydryl enzyme Na+, K+ -ATPase: an effect dependent on the tellurium atom.

Science.gov (United States)

Quines, Caroline B; Rosa, Suzan G; Neto, José S S; Zeni, Gilson; Nogueira, Cristina W

2013-11-01

Organotellurium compounds are known for their toxicological effects. These effects may be associated with the chemical structure of these compounds and the oxidation state of the tellurium atom. In this context, 2-phenylethynyl-butyltellurium (PEBT) inhibits the activity of the sulfhydryl enzyme, δ-aminolevulinate dehydratase. The present study investigated on the importance of the tellurium atom in the PEBT ability to oxidize mono- and dithiols of low molecular weight and sulfhydryl enzymes in vitro. PEBT, at high micromolar concentrations, oxidized dithiothreitol (DTT) and inhibited cerebral Na(+), K(+)-ATPase activity, but did not alter the lactate dehydrogenase activity. The inhibition of cerebral Na(+), K(+)-ATPase activity was completely restored by DTT. By contrast, 2-phenylethynyl-butyl, a molecule without the tellurium atom, neither oxidized DTT nor altered the Na(+), K(+)-ATPase activity. In conclusion, the tellurium atom of PEBT is crucial for the catalytic oxidation of sulfhydryl groups from thiols of low molecular weight and from Na(+), K(+)-ATPase.

Study On Analytical Methods Of Tellurium Content In Natriiodide (Na131I) Radiopharmaceutical Solution Produced In The Dalat Nuclear Reactor

International Nuclear Information System (INIS)

Vo Thi Cam Hoa; Duong Van Dong; Nguyen Thi Thu; Chu Van Khoa

2007-01-01

This report describes the practical methods for analyzing of Tellurium content in Na 131 I solution produced at the Dalat Nuclear Research Institute. We studied analytical methods to control Tellurium content in final Na 131 I solution product used in medical purposes by three methods such as: spot test, gamma spectrometric and spectrophotometric methods. These investigation results are shown that the spot test method is suitable for controlling Tellurium trace in the final product. This spot test can be determinate Tellurium trace less than 10 ppm and are used to quality control of Na 131 I solution using in medical application. (author)

Simple and effective method for nuclear tellurium isomers separation from antimony cyclotron targets

International Nuclear Information System (INIS)

Bondarevskij, S.I.; Eremin, V.V.

1999-01-01

Simple and effective method of generation of tellurium nuclear isomers from irradiated on cyclotron metallic antimony is suggested. Basically this method consists in consideration of the big difference in volatilities of metallic forms of antimony, tin and tellurium. Heating of the tin-antimony alloy at 1200 K permits to separate about 90 % of produced quantity of 121m Te and 123m Te (in this case impurity of antimony radionuclides is not more than 1 % on activity) [ru

Simultaneous determination of selenium and tellurium in native sulfur by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Arikawa, Yoshiko; Hirai, Shoji; Ozawa, Takejiro.

1979-01-01

A method for the determination of selenium and tellurium in native sulfur has been investigated by means of atomic absorption spectrophotometry. Native sulfur collected from around fumarole or volcanic crater is ground down into powder, a portion of which weighing 1 g is subjected to analysis. A 2.6% (w/v) sodium hydroxide solution is added by 10 ml to the sample in a teflon beaker, and the mixture is then heated on a hot plate. Sulfur is decomposed and dissolved in the form of disulfide and thiosulfate. A 30% hydrogenperoxide solution is added by 10 ml to oxidize them to sulfate. At the same time selenium and tellurium contained in the sulfur sample are also thought to be oxidized to Se(VI) and Te(VI) states. The solution is neutralized with hydrochloric acid and diluted with distilled water to 100 ml. The sample solution thus prepared is sprayed into the air-acetylene flame of the atomic absorption spectrophotometer. The absorbance is measured at 195.9 nm for selenium and 214.2 nm for tellurium. Calibration curve is prepared by measuring the absorbances of the solutions prepared as follows. One gram portions of pure sulfur (99.9999%) are decomposed as for the samples. After neutralization, standard solutions containing each same amount of selenium and tellurium (0 -- 1000 μg) are added to the sulfur solution and then diluted with water to 100 ml. The standard deviations were estimated to be 50.4 ppm for selenium at 756 ppm and 16.6 ppm for tellurium at 587 ppm. For the check of the reliability of the method, results were compared with those obtained by neutron activation analysis. Results obtained by both methods showed good agreement. (author)

Selenium- or tellurium- containing bile acids and derivatives thereof

International Nuclear Information System (INIS)

Monks, R.; Riley, A.L.M.

1981-01-01

This invention relates to the preparation of selenium and tellurium derivatives, particularly γ-emitting radioactive derivatives of bile acids and bile salts. Such compounds are valuable in the examination of body function, especially small bowel function. (author)

Electrochemical characterization of the underpotential deposition of tellurium on Au electrode

International Nuclear Information System (INIS)

Zhu, W.; Yang, J.Y.; Zhou, D.X.; Bao, S.Q.; Fan, X.A.; Duan, X.K.

2007-01-01

Electrochemical characterization of the underpotential deposition (UPD) of tellurium on Au substrate has been performed in this paper. The mechanism of Te deposition and its voltammetry dependence on the Te ion concentration were studied, and it suggests that variations in the metal ion concentration may affect the UPD process kinetics. The effect of tellurium adsorbates on UPD behavior of Te has also been investigated. The results show that the tellurium adsorbates could be irreversibly adsorbed upon the Au substrate surface under the open-circuit conditions. Subsequent removal of the Te adsorbates was also proved to be very difficult within the Au double-layer region, and a standard electrochemical cleaning procedure is necessary to remove the Te adsorbates completely. When the potential was cycled into the Au oxidation region, a substantial loss of Te adsobates was observed, which occurs simultaneously with the Au oxidation features. Scan rate dependent cyclic voltammetry experiments reveal that the peak current in the Te UPD peak is not a linear function of the scan rate, ν, but of a 2/3 power of the scan rate, ν 2/3 . It is in good consistent with a two-dimension nucleation and growth mechanism

Intergranular tellurium cracking of nickel-based alloys in molten Li, Be, Th, U/F salt mixture

Science.gov (United States)

Ignatiev, Victor; Surenkov, Alexander; Gnidoy, Ivan; Kulakov, Alexander; Uglov, Vadim; Vasiliev, Alexander; Presniakov, Mikhail

2013-09-01

In Russia, R&D on Molten Salt Reactor (MSR) are concentrated now on fast/intermediate spectrum concepts which were recognized as long term alternative to solid fueled fast reactors due to their attractive features: strong negative feedback coefficients, easy in-service inspection, and simplified fuel cycle. For high-temperature MSR corrosion of the metallic container alloy in primary circuit is the primary concern. Key problem receiving current attention include surface fissures in Ni-based alloys probably arising from fission product tellurium attack. This paper summarizes results of corrosion tests conducted recently to study effect of oxidation state in selected fuel salt on tellurium attack and to develop means of controlling tellurium cracking in the special Ni-based alloys recently developed for molten salt actinide recycler and tranforming (MOSART) system. Tellurium corrosion of Ni-based alloys was tested at temperatures up to 750 °C in stressed and unloaded conditions in molten LiF-BeF2 salt mixture fueled by about 20 mol% of ThF4 and 2 mol% of UF4 at different [U(IV)]/[U(III)] ratios: 0.7, 4, 20, 100 and 500. Following Ni-based alloys (in mass%): HN80М-VI (Mo—12, Cr—7.6, Nb—1.5), HN80МТY (Mo—13, Cr—6.8, Al—1.1, Ti—0.9), HN80МТW (Mo—9.4, Cr—7.0, Ti—1.7, W—5.5) and ЕМ-721 (W—25.2, Cr—5.7, Ti—0.17) were used for the study in the corrosion facility. If the redox state the fuel salt is characterized by uranium ratio [U(IV)]/[U(III)] uranium intermetallic compounds and alloys with nickel and molybdenum. This leads to spontaneous behavior of alloy formation processes on the specimens' surface and further diffusion of uranium deep into the metallic phase. As consequence of this films of intermetallic compounds and alloys of nickel, molybdenum, tungsten with uranium are formed on the alloys specimens' surface, and intergranular corrosion does not take place. In the fuel salt with [U(IV)]/[U(III)] = 4-20 the potentials of uranium

Selenium Se and tellurium Te

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for determining selenium and tellurium in various objects are presented. The bichromatometric determination of Te in cadmium, zinc and mercury tellurides is based on oxidation of Te(4) to (6) in H 2 SO 4 with potassium bichromate. In steels, Te is determined photometrically with the aid of KI. The determination is hindered by Fe(3), Cu(2), Bi(3) and Se(4) ions, which must be separated. The extraction-photometric determination of Te in native sulfur is carried out with the aid of 5-mercapto-3-(naphthyl-2)-1,3,4-thiadiazolthione-2 (pH=4.8-5.0). The dyed complex is readily extracted with chloroform and benzene. The spectrophotometric determination of Te in selenium is performed with the aid of 3,5-diphenylpyrazoline-1-dithiocarbamate of sodium. Te is determined in commercial indium, arsenic and their semiconductor compounds photometrically with the aid of copper diethyldithiocarbamate. The method permits determining 5x10 -5 % Te in a weighed amount of 0.5 g. The chloride complex of Te(4) with diantipyriodolpropylmethane is quantitatively extracted with dichloroethane from hydrochloric acid solutions. Thus, any amounts of Te can be separated from Se and determined photometrically. The extraction-photometric determination of Te in commercial lead and bismuth is carried out with the aid of pyrazolone derivatives, in commercial copper with the aid of diantipyridolpropylmethane, and in ores (more than 0.01% Te) with the aid of bismuthol 2. Also described is the extraction-polarographic determination of Te in sulfide ores

Determination of tellurium in coal samples by means of graphite furnace atomic absorption spectrometry after coprecipitation with iron(III) hydroxide

Energy Technology Data Exchange (ETDEWEB)

Oda, S.; Arikawa, Y. [Japan Womens University, Tokyo (Japan)

2005-11-01

A simple and accurate method for the determination of tellurium in coal samples was investigated by the combustion of samples under a high pressure of oxygen and coprecipitation with Fe(OH){sub 3}, followed by a measurement by graphite furnace atomic absorption spectrometry (GF-AAS). About 0.5 g of an accurately weighed ground coal sample and 0.5 g of starch were combusted in an oxygen combustion bomb filled with oxygen to 3 MPa and added with 3 ml of water as an absorbing solution. The formed tellurium trioxide TeOs dissolved in water as TeO{sub 4}{sup 2-}, which was in turn reduced to TeO{sub 3}{sup 2-} by heating. After diluting the above-mentioned solution up to about 50 ml with water, Fe(OH){sub 3} is formed upon adding Fe(NO{sub 3}){sub 3} and sodium hydroxide solutions at pH 8-9 and left standing overnight. After dissolving the precipitate by HCl, the solution was diluted to 10 ml with water and the concentration of tellurium was measured by GF-AAS at a wavelength of 214.3 nm. The standard addition method was employed for the determination of tellurium in real coal samples, because those processes for the formation of tellurium(VI) oxide and coprecipitation with Fe(OH)3 were interfered by matrices. For NIST SRM 1632c, the standard coal sample tellurium content of 0.057 {+-} 0.004 mg kg{sup -1} was in good agreement with the information value of 0.05 mg kg{sup -1} with 7% of RSD in five replicate analyses. The tellurium contents in 20 real coal samples given by Center for Coal Utilization, Japan were also determined. The tellurium contents in these samples were scattered over the narrow range between 0.032 and 0.100 mg kg{sup -1}.

Site-specific nucleation and controlled growth of a vertical tellurium nanowire array for high performance field emitters

International Nuclear Information System (INIS)

Safdar, Muhammad; Zhan Xueying; Mirza, Misbah; Wang Zhenxing; Sun Lianfeng; He Jun; Niu Mutong; Zhang Jinping; Zhao Qing

2013-01-01

We report the controlled growth of highly ordered and well aligned one-dimensional tellurium nanostructure arrays via a one-step catalyst-free physical vapor deposition method. The density, size and fine structures of tellurium nanowires are systematically studied and optimized. Field emission measurement was performed to display notable dependence on nanostructure morphologies. The ordered nanowire array based field emitter has a turn-on field as low as 3.27 V μm −1 and a higher field enhancement factor of 3270. Our finding offers the possibility of controlling the growth of tellurium nanowire arrays and opens up new means for their potential applications in electronic devices and displays. (paper)

Exploring molecular and spin interactions of Tellurium adatom in reduced graphene oxide

Energy Technology Data Exchange (ETDEWEB)

Alegaonkar, Ashwini [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India); Alegaonkar, Prashant [Department of Applied Physics, Defence Institute of Advance Technology, Girinagar, Pune, 411 025, MS (India); Pardeshi, Satish, E-mail: skpar@chem.unipune.ac.in [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India)

2017-07-01

The transport of spin information fundamentally requires favourable molecular architecture and tunable spin moments to make the medium pertinent for spintronic. We report on achieving coherent molecular-spin parameters for rGO due to Tellurium (Te) adatom. Initially, GO prepared using graphite, was modified into rGO by in situ incorporation of 1 (w/w)% of Te. Both the systems were subjected to ESCA, FTIR, Raman dispersion, ESR spectroscopy, and electron microscopy. Analysis revealed that, Te substantially reacted with epoxides, carbonyl, and carboxylate groups that improved C-to-O ratio by twice. However, the spin splitting character, between Te and C, seems to be quenched. Moreover, Te altered the dynamical force constant between C-C and C=C that generated the mechanical stress within rGO network. The layer conjugation, nature of folding, symmetry, and electronic states of the edges were also affected by precipitation and entrapment of Te. The calculated dynamic molecular Raman and ESR spin parameters indicated that, Te acted as a bridging element for long range spin transport. This is particularly due to, the p-orbital moments of Te contributing, vectorially, to spin relaxation process operative at broken inversion symmetry sites. Our study suggests that, facile addition of Te in rGO is useful to achieve favourable spintronic properties. - Highlights: • Spin interactions and molecular dynamics modification due to Tellurium adatom in rGO. • Molecular level manipulation of Tellurium adatom for favourable spintronic properties. • Bychocov-Rashaba coupling are the operative channels in rGO. • Extrinsic coupling component get added vectorially by Tellurium. • Te-rGO is a viable medium for molecular spintronics.

Dismantling and chemical characterization of spent Peltier thermoelectric devices for antimony, bismuth and tellurium recovery.

Science.gov (United States)

Balva, Maxime; Legeai, Sophie; Garoux, Laetitia; Leclerc, Nathalie; Meux, Eric

2017-04-01

Major uses of thermoelectricity concern refrigeration purposes, using Peltier devices, mainly composed of antimony, bismuth and tellurium. Antimony was identified as a critical raw material by EU and resources of bismuth and tellurium are not inexhaustible, so it is necessary to imagine the recycling of thermoelectric devices. That for, a complete characterization is needed, which is the aim of this work. Peltier devices were manually dismantled in three parts: the thermoelectric legs, the alumina plates on which remain the electrical contacts and the silicone paste used to connect the plates. The characterization was performed using five Peltier devices. It includes mass balances of the components, X-ray diffraction analysis of the thermoelectric legs and elemental analysis of each part of the device. It appears that alumina represents 45% of a Peltier device in weight. The electrical contacts are mainly composed of copper and tin, and the thermoelectric legs of bismuth, tellurium and antimony. Thermoelectric legs appear to be Se-doped Bi 2 Te 3 and (Bi 0,5 Sb 1,5 )Te 3 for n type and p type semiconductors, respectively. This work shows that Peltier devices can be considered as a copper ore and that thermoelectric legs contain high amounts of bismuth, tellurium and antimony compared to their traditional resources.

Comparison of analytical possibilities of inversion voltammetry of tellurium with cathodic and anodic potential scanning taking layer-by-layer analysis of GaAs-Te films as example

International Nuclear Information System (INIS)

Kaplin, A.A.; Portnyagina, Eh.O.; Gridaev, V.F.

1979-01-01

Possibility of application in analytical purposes of the process of tellurium precipitation electrosolution from the surfaces of graphite and mercury-graphite electrodes at the cathode scanning of the potential is shown. As a result of comparison of direct and inversion scanning with cathodic and anodic scanning of the potential, variants of voltammetric method of tellurium determination in artificial solutions and, taking the developed method of layer-by-layer analysis of the GaAsTe films as an example, advantage of mercury-graphite electrode with cathodic scanning as compared to graphite electrode with cathode scanning of the potential is shown. Reproducibility of the GaAs film analysis results according to anodic and cathodic tellurium peaks is satisfactory. Maximum deviation from the results of analysis of oxidation peaks and tellurium peduction does not exceed 15 rel. %. Thus, for tellurium concentrations, exceeding 5x10 -6 g-ion/l, both anodic and cathodic scanning of the potential can be used, though error in tellurium determination according to cathodic peaks is 1.5-2.0 times higher. At tellurium amounts lower 5x10 -6 g-ion/l the determination should be carried out according to the peaks of tellurium anodic oxidation from the surface of graphite electrode or according to the peaks of tellurium cathodic reduction from the surface of mercury-graphite electrode

Modelling the chemical behaviour of tellurium species in the reactor pressure vessel and the reactor cooling system under severe accident conditions

International Nuclear Information System (INIS)

Alonso, A.; Gonzalez, C.

1991-07-01

This state of the art report contains information on the behaviour of tellurium and its compounds in the reactor pressure vessel and the reactor coolant system under light water reactor severe accident conditions. To characterise tellurium behaviour, it is necessary the previous knowledge of the species of tellurium released from the core, and simultaneity of its release with that of other materials which can alter the transport, for instance, control rod and structural materials. Release and transport experiments have been reviewed along with the models implemented in the codes which are used in the international community: TRAPMELT, RAFT, VICTORIA and SOPHIE. From the experiments, it can be concluded that other species different to Te 2 , such as tin telluride and cesium telluride, may be released from the fuel. That is why they must be considered in the transport phenomena. There is also experimental evidence of the strong interaction of Te 2 with Inconel 600 and stainless steel of the pipe walls and structures, however this strong interaction is in competition with the interaction of tellurium with aerosols, which under severe accident conditions may represent an area greater than that of the primary system. It is for the absence of significant tellurium species in the transport models, and also for the interaction of tellurium with aerosols, for which some codes show the greatest deficiencies

The enhancing of Au-Ag-Te content in tellurium-bearing ore mineral by bio-oxidation-leaching

Science.gov (United States)

Kim, PyeongMan; Kim, HyunSoo; Myung, EunJi; Kim, YoonJung; Lee, YongBum; Park*, CheonYoung

2015-04-01

The purpose of this study is to enhance the content of valuable metals such as Au-Ag-Te in tellurium-bearing minerals by bio-oxidation-leaching. It was confirmed that pyrite, chalcopyrite, sphalerite and galena were produced together with tellurium-bearing minerals including hessite, sylvanite and tellurobismuthite from ore minerals and concentrates through microscopic observation and SEM/EDS analysis. In a bio-oxidation-leaching experiment, with regard to Au, Ag, Te, Cu and Fe, the changes in the amount of leaching and the content of leaching residues were compared and analyzed with each other depending on the adaptation of an indigenous microbe identified as Acidithiobacillus ferrooxidans. As a result of the experiment, the Au-Ag-Te content in tellurium-bearing ore mineral was enhanced in the order of physical oxidation leaching, physical/non-adaptive bio-oxidation-leaching and physical/adaptive biological leaching. It suggests that the bio-oxidation-leaching using microbes adapted in tellurium-bearing ore mineral can be used as a pre-treatment and a main process in a recovery process of valuable metals. "This research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education(NRF-2013R1A1A2004898)"

ELECTROCHEMICAL STUDY OF RHENIUM-TELLURIUM-COPPER SYSTEM

OpenAIRE

E.A.Salakhova*1, D.B.Tagiyev2, P.E.Kalantarova3 and A.M.Askerova4

2017-01-01

The formation of the triple alloys Re-Te-Cu on the platinum electrode at volt amperemetric cycling has been studied. The investigation was carried out from chloride acidic solution containing tellurium acid, potassium perrhenate, chloride copper. The kinetics of the processes was controlled using the measurements by the method of cyclic volt-amperometry on the device İVİUMSTAT. For the analysis of composition and structure the methods of XRD (X-ray diffraction analysis) were used, and the inv...

Acousto-optic measurements of ultrasound attenuation in tellurium dioxide crystal

International Nuclear Information System (INIS)

Voloshinov, V. B.; Lemyaskina, E. A.

1996-01-01

The paper is devoted to experimental investigation of ultrasound propagation in tellurium dioxide monocrystal. In particular, attenuation of slow shear acoustic modes in the crystal was measured. The measurements were performed by acousto-optic methods using probing of acoustic column by a laser beam. The paper describes measurements of acoustic attenuation coefficient for slow shear ultrasonic waves propagating at an angle =4.5 O with respect to the (110) direction in the (110) plane. The investigation was made at acoustic frequency f = 100 MHz with pulsed acoustic waves and with an optical beam of a He-Ne laser. It is found that the attenuation coefficient is α = 0.57 cm -1 ± 15 %. The attenuation at acoustic frequencies f ≥ 100 MHz influences performance characteristics of acousto-optical devices based on tellurium dioxide. As proved, spectral resolution of a quasicollinear acoustooptic filter decreases by a factor of 2 compared to a case of the attenuation absence. (authors)

Copper Tellurium Oxides - A Playground for Magnetism.

Energy Technology Data Exchange (ETDEWEB)

Norman, M. R.

2018-04-15

A variety of copper tellurium oxide minerals are known, and many of them exhibit either unusual forms of magnetism, or potentially novel spin liquid behavior. Here, I review a number of the more interesting materials with a focus on their crystalline symmetry and, if known, the nature of their magnetism. Many of these exist (so far) in mineral form only, and most have yet to have their magnetic properties studied. This means a largely unexplored space of materials awaits our exploration.

Liquid-liquid extraction of arsenic, antimony, selenium and tellurium by zinc diethyldithiocarbamate

International Nuclear Information System (INIS)

Bajo, S.; Wyttenbach, A.

1978-03-01

The authors report the solvent extraction, oxidation, reduction, extraction in the presence of iron, and reextraction of arsenic, antimony, selenium and tellurium. These processes were studied using radioactive tracers. (G.T.H.)

First example of a high-level correlated calculation of the indirect spin-spin coupling constants involving tellurium

DEFF Research Database (Denmark)

Rusakov, Yury Yu; Krivdin, Leonid B.; Østerstrøm, Freja From

2013-01-01

This paper documents a very first example of a high-level correlated calculation of spin-spin coupling constants involving tellurium taking into account relativistic effects, vibrational corrections and solvent effects for the medium sized organotellurium molecules. The 125Te-1H spin-spin coupling...... constants of tellurophene and divinyl telluride were calculated at the SOPPA and DFT levels in a good agreement with experiment. A new full-electron basis set av3z-J for tellurium derived from the "relativistic" Dyall's basis set, dyall.av3z, and specifically optimized for the correlated calculations...... of spin-spin coupling constants involving tellurium, was developed. The SOPPA methods show much better performance as compared to 15 those of DFT, if relativistic effects calculated within the ZORA scheme are taken into account. Vibrational and solvent corrections are next to negligible, while...

A Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

OpenAIRE

Berman, G. P.; Doolen, G. D.; Tsifrinovich, V. I.

2000-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines the well-developed silicon technology with expected advances in MRFM.

Subnanosecond pulse measurements of 10.6 μm radiation with tellurium

NARCIS (Netherlands)

Haselhoff, E.H.; Bonnie, R.J.M.; Ernst, G.J.; Witteman, W.J.

1988-01-01

Subnanosecond infrared pulses have been measured by noncollinear secondharmonic generation in tellurium. The method is very practical because due to the high refractive index the fine tuning of the phase matching is easily obtained by rotating the crystal around the optic axis.

Flotation concentration for tellurium determination in industrial sewage

International Nuclear Information System (INIS)

Skripchuk, V.G.; Bormotova, L.V.; Lukoyanova, L.P.; Tret'yakova, M.I.

1983-01-01

Combination of the flotation of tellurium (4) precipitate with papaverine toluene and extraction-photometric determination of Te with butylrhodamine C allows one to determine 0.002-0.1 mg Te/l without its preliminary precipitation. Accompanying elements found in non-ferrous metallurgy sewage have no effect upon it. The duration of analysis of 10 samples is 1 to 1.5 h. Relative error is 12%. The method is introduced at the ''Uralelektromed'' plant

Magnetic resonance force microscopy quantum computer with tellurium donors in silicon.

Science.gov (United States)

Berman, G P; Doolen, G D; Hammel, P C; Tsifrinovich, V I

2001-03-26

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations.

Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

International Nuclear Information System (INIS)

Berman, G. P.; Doolen, G. D.; Hammel, P. C.; Tsifrinovich, V. I.

2001-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

International Nuclear Information System (INIS)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F.

2013-01-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

Energy Technology Data Exchange (ETDEWEB)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F., E-mail: julio.ruivo.costa@usp.br, E-mail: czamboni@ipen.br, E-mail: fisicawagner@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

The dependence of the texture of tellurium thin films on vacuum deposition angle

International Nuclear Information System (INIS)

Cocks, F.H.; Peterson, M.J.; Jones, P.L.

1980-01-01

Vacuum-deposited tellurium thin films can show substantially different surface morphologies depending on the angle with which the vapor stream impinges on the substrate surface. These tellurium thin films have a tendency to grow as acicular crystallites but as the deposition angle is increased so that the vapor stream becomes tangential to the substrate surface the spacing between crystallites increases and approaches, at stream angles of approximately 80 0 from the normal, dimensions roughly once or twice the average wavelength of visible light. Such films may have application in solar energy collector systems because of the high absorptivity of sunlight shown by such films. Mechanisms which describe the tendency for crystallite spacing to increase with increasing angle are discussed. (Auth.)

Iodine-129 in thyroids and tellurium isotopes in meteorites by neutron activation analysis

International Nuclear Information System (INIS)

Ballad, R.V.

1978-06-01

A combination of neutron activation and mass spectrometry has been used to determine the concentration of fissiogenic 129 I and the value of the 129 I/ 127 I ratio in thyroids of man, cow, and deer from Missouri. Deer thyroids show an average value of 129 I/ 127 I = 1.8 x 10 -8 and an average concentration of 3 x 10 -3 pCi 129 I per gram of thyroid (wet weight). Thyroids of cows and humans show successively lower values for the 129 I/ 127 I ratio and the 129 I content because their diets dilute fission-produced 129 I in the natural iodine cycle with mineral iodine. The results of analyses on a few thyroids from other geographic areas are also reported. The isotopic compositions of tellurium, krypton, and xenon were determined in acid-resistant residues of the Allende meteorite. Neutron activation and γ-counting were used to determine the relative abundances of six tellurium isotopes, and mass spectrometry was used to determine the isotopic compositions of krypton and xenon in aliquots of the same residues. Nucleogenetic anomalies were observed in the isotopic compositions of these three elements. The presence of isotopically distinct components of tellurium, krypton, and xenon in these residues provides strong support for the suggestion that our solar system formed directly from the debris of a supernova

Synthesis and characterization of the [Te(SCN2H4)4] (SO4)2 complex. Application to the separation of 99Mo from fission products

International Nuclear Information System (INIS)

Mestnik, S.A.C.; Silva, C.P.G. da.

1988-10-01

Thiourea reacts with tellurium-IV ions, in sulfuric medium, to form cationic complex which is strongly retained on cationic ion exchanger. The method was applied to separate 99 Mo from 132 Te obtained in the fission of 235 U since molybdenum does not form such complex and passes throught the cationic exchanger column in the molibdate form. In this paper, the procedure of the tellurium-thiourea complex preparation and its characterization are described. Elemental analysis, ultraviolet and infra-red absorption spectrophotometry as well as thermogravimetry were used to characterize the complex. (author) [pt

Thermoelectric properties of bismuth antimony tellurium thin films through bilayer annealing prepared by ion beam sputtering deposition

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhuang-hao [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Fan, Ping, E-mail: fanping308@126.com [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Luo, Jing-ting [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Cai, Xing-min; Liang, Guang-xing; Zhang, Dong-ping [College of Physics Science and Technology, Shenzhen University, 518060 (China); Ye, Fan [Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China)

2014-07-01

Bismuth antimony tellurium is one of the most important tellurium-based materials for high-efficient thermoelectric application. In this paper, ion beam sputtering was used to deposit Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films on borosilicate substrates at room-temperature. Then the bismuth antimony tellurium thin films were synthesized via post thermal treatment of the Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films. The effect of annealing temperature and compositions on the thermoelectric properties of the thin films was investigated. After the thin films were annealed from 150 °C to 350 °C for 1 h in the high vacuum condition, the Seebeck coefficient changed from a negative sign to a positive sign. The X-ray diffraction results showed that the synthesized tellurium-based thermoelectric thin film exhibited various alloys phases, which contributed different thermoelectricity conductivity to the synthesized thin film. The overall Seebeck coefficient of the synthesized thin film changed from negative sign to positive sign, which was due to the change of the primary phase of the tellurium-based materials at different annealing conditions. Similarly, the thermoelectric properties of the films were also associated with the grown phase. High-quality thin film with the Seebeck coefficient of 240 μV K{sup −1} and the power factor of 2.67 × 10{sup −3} Wm{sup −1} K{sup −2} showed a single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase when the Sb/Te thin film sputtering time was 40 min. - Highlights: • Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} thermoelectric thin films synthesized via bilayer annealing • The film has single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase with best thermoelectric performance. • The film has high thermoelectric properties comparable with other best results.

Equilibrium state of delta-phase with tellurium in the Sb-Bi-Te system

International Nuclear Information System (INIS)

Gajgukova, V.S.; Dudkin, L.D.; Erofeev, R.S.; Musaelyan, V.V.; Nadzhip, A.Eh.; Sokolov, O.B.

1978-01-01

A research has been carried out with a view to establish the equilibrium state of delta-phase of the composition (Sbsub(1-x)Bisub(x)) 2 Te 3 with tellurium, depending on x and temperature. The Hall effect, the thermoelectromotive force, and the electric conductivity of the samples of Sb-Bi-Te alloys have been measured, the samples being annealed at various temperatures (550 to 250 deg C). The measurement results have shown that as the Bi 2 Te 3 content in the solid solutions increases and temperature decreases, the delta-phase-Te boundary monotonously approaches the stoichiometric composition. Using the research carrid out as the basis, the general character of the equilibrium delta-phase with tellurium boundary has been rendered more precise in Sb-Bi-Te system, depending on the temperature and Bi content (up to 25 at.%)

GALVANIC MAGNETIC PROPERTIES OF BISMUTH THIN FILMS DOPED WITH TELLURIUM MADE BY THERMAL VACUUM EVAPORATION

Directory of Open Access Journals (Sweden)

V. A. Komarov

2013-01-01

Full Text Available The influence of n-type impurity of tellurium (concentration range from 0.005 atomic % Te to 0.15 atomic % Te on galvanic magnetic properties (resistivity, magnetic resistance and Hall constant of Bi thin films with various thicknesses was studied. The properties were measured in temperature range from 77 to 300 K. It was established that the classical size effect in the films is significant and decreases with higher concentration of Te impurity. The analysis of experimental results was carried out in approximation of the law of Jones-Schoenberg dispersion for Bi films doped with tellurium. Calculation of concentration and mobility of charge carriers in the studied films was made.

Hydrogen-assisted post-growth substitution of tellurium into molybdenum disulfide monolayers with tunable compositions

Science.gov (United States)

Yin, Guoli; Zhu, Dancheng; Lv, Danhui; Hashemi, Arsalan; Fei, Zhen; Lin, Fang; Krasheninnikov, Arkady V.; Zhang, Ze; Komsa, Hannu-Pekka; Jin, Chuanhong

2018-04-01

Herein we report the successful doping of tellurium (Te) into molybdenum disulfide (MoS2) monolayers to form MoS2x Te2(1-x) alloy with variable compositions via a hydrogen-assisted post-growth chemical vapor deposition process. It is confirmed that H2 plays an indispensable role in the Te substitution into as-grown MoS2 monolayers. Atomic-resolution transmission electron microscopy allows us to determine the lattice sites and the concentration of introduced Te atoms. At a relatively low concentration, tellurium is only substituted in the sulfur sublattice to form monolayer MoS2(1-x)Te2x alloy, while with increasing Te concentration (up to ˜27.6% achieved in this study), local regions with enriched tellurium, large structural distortions, and obvious sulfur deficiency are observed. Statistical analysis of the Te distribution indicates the random substitution. Density functional theory calculations are used to investigate the stability of the alloy structures and their electronic properties. Comparison with experimental results indicate that the samples are unstrained and the Te atoms are predominantly substituted in the top S sublattice. Importantly, such ultimately thin Janus structure of MoS2(1-x)Te2x exhibits properties that are distinct from their constituents. We believe our results will inspire further exploration of the versatile properties of asymmetric 2D TMD alloys.

Electric field fluctuations in liquid tellurium alloys a hint to bond character

NARCIS (Netherlands)

Paulick, C.A.; Brinkmann, R.; Elwenspoek, Michael Curt; von Hartrott, M.; Kiehl, M.; Maxim, P.; Quitmann, D.

1985-01-01

Atomic scale electric field fluctuations in liquid tellurium alloys are detected as they induce nuclear spin relaxation rate RQ in noble gas impurity atoms, via quadrupolar interaction. Results for Xe in liquid Ag, Ga, In, Tl, Ge, Sn---Te alloys are discussed, assuming that bonding in these alloys

Vaporization studies on elemental tellurium and selenium by Knudsen effusion mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, R., E-mail: rvis1953@gmail.com; Balasubramanian, R., E-mail: rbs@igcar.gov.in; Darwin Albert Raj, D., E-mail: darwinalbertraj1953@gmail.com; Sai Baba, M., E-mail: msb@igcar.gov.in; Lakshmi Narasimhan, T.S., E-mail: tslak@igcar.gov.in

2014-08-01

Highlights: • A detailed KEMS study of vaporization of elemental tellurium and selenium systems. • Clusters Te{sub i}(g) (i = 2 to 7) and Se{sub i}(g) (i = 2 to 9) identified over Te(s) and Se(s). • p–T relations for Te{sub i}(g) (590 to 690 K) and Se{sub i}(g) (380 to 480 K). • Vapor phase of Te dominated by Te{sub 2}(g) (∼95%) while that of Se by Se{sub 6}(g) (∼50%) and Se{sub 5}(g) (∼25%). • Sublimation and atomization enthalpies deduced for Te{sub i}(g) and Se{sub i}(g). - Abstract: Vaporization studies on elemental tellurium and selenium were conducted by Knudsen effusion mass spectrometry in the temperature range of 590–690 K and 380–480 K, respectively. The ionic species Te{sub i}{sup +} (i = 1–7) and Se{sub i}{sup +}(g) (i = 1–9) were detected in the mass spectra over these two condensed phases. Measurement of ion intensities were performed as a function of electron impact energy and as a function of temperature (at different electron impact energies) for identifying the gaseous precursor species as well as for determining the partial pressure–temperature relations and sublimation enthalpies for these species. While the major species over elemental tellurium was confirmed to be Te{sub 2}(g) (with all other gaseous species Te{sub 3}–Te{sub 7} put together constituting less than 5%), the major species over elemental selenium was found to be Se{sub 6}(g), closely followed by Se{sub 5}(g) (with other gaseous species Se{sub 2}–Se{sub 4} and Se{sub 7}–Se{sub 9} put together also moderately constituting ∼25%). From the partial pressures, the thermodynamic data for the sublimation reactions i Te(s) = Te{sub i}(g) and i Se(s) = Se{sub i}(g) were deduced by second- and third-law methods. The atomization enthalpies of tellurium and selenium clusters were also deduced by using the recommended enthalpies of formation of monomeric species. Comparison of the findings obtained in the present study with those in previous studies revealed

Starting material radiation source for Moessbauer investigations of tellurium compounds

International Nuclear Information System (INIS)

Alexandrov, A.J.; Grushko, J.S.; Makarov, E.F.; Mishin, K.Y.; Baltrunas, D.A.J.

1977-01-01

A method is described of preparing a radiation source for Mossbauer investigations of tellurium compounds manufactured on the basis of 5 MgO . Te 124 O 3 . 5 MgO . Te 124 O 3 is irradiated in a reactor by means of thermal neutrons, followed by annealing at a temperature ranging from 600 0 to 1,100 0 C for a period of from 5 to 10 hours

Synthesis of ultra-thin tellurium nanoflakes on textiles for high-performance flexible and wearable nanogenerators

Energy Technology Data Exchange (ETDEWEB)

He, Wen; Van Ngoc, Huynh; Qian, Yong Teng; Hwang, Jae Seok; Yan, Ya Ping [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of); Choi, Hongsoo [Department of Robotics Engineering, Daegu Gyeongbuk Institute of Science and Technology (DGIST), 711-873, Daegu (Korea, Republic of); Kang, Dae Joon, E-mail: djkang@skku.edu [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of)

2017-01-15

Highlights: • Ultra-thin tellurium (Te) nanoflakes were successfully grown on textile and used as an active piezoelectric material. • Te nanoflake nanogenerator device was systematically studied by bending and compressing test. • The ultra-high output power during compressing test can light up 10 LEDs without any external power source. • The device can offer a breakthrough in applying tellurium nanoflakes into high-performance flexible and wearable piezoelectric nanogenerator. - Abstract: We report that ultra-thin tellurium (Te) nanoflakes were successfully grown on a sample of a gold-coated textile, which then was used as an active piezoelectric material. An output voltage of 4 V and a current of 300 nA were obtained from the bending test under a driving frequency of 10 Hz. To test the practical applications, Te nanoflake nanogenerator (TFNG) device was attached to the subject’s arm, and mechanical energy was converted to electrical energy by means of periodic arm-bending motions. The optimized open-circuit voltage and short-circuit current density of approximately 125 V and 17 μA/cm{sup 2}, respectively, were observed when a TFNG device underwent a compression test with a compressive force of 8 N and driving frequency of 10 Hz. This high-power generation enabled the instantaneous powering of 10 green light-emitting diodes that shone without any assistance from an external power source.

Catalytic activity of oxide cerium-molybdenum-tellurium catalysts in oxidation ammonolysis

International Nuclear Information System (INIS)

Dzhordano, N.; Bart, D.; Madzhori, R.

1984-01-01

A commercial catalyst containing a mixture of Ce-, Mo-, Te oxides deposited on SiO 2 is shown to manifest a high efficiency in oxidative ammonolysis of propylene (C 3 - ) to acrylonitrile (AN). The dependence of the catalytic properties on the catalyst composition and reaction conditions is studied. It is established that three-component mixtures are more active and selective than the systems with a lesser number of components. Using the catalyst with the optimum ratio of constituent oxides in a microreactor at 440 deg enabled one to achieve initial selectivity in terms of AN equal to 82.5% at 97% conversion of C 3 - . Acrolein, acetonitrile, HCN and nitrogen oxides are the reaction by-products. A supposition is made that the reaction proceeds via the formation of π-compleXes on the centres of Te(4). Setective oxidation occurs on oxygen atoms bonded with the Mo(6) ions. Tellurium enhances the molybdenum reducibleness due to delocalization of electrons, whereas the cerium addition to the mixture of tellurium- and molybdenum oxides increases the rate of molybdenum reoxidation and thus enhances the catalytic system stability

The anti-inflammatory effects of the tellurium redox modulating compound, AS101, are associated with regulation of NFκB signaling pathway and nitric oxide induction in macrophages

Directory of Open Access Journals (Sweden)

Sredni Benjamin

2010-01-01

Full Text Available Abstract Background LPS-activated macrophages produce mediators which are involved in inflammation and tissue injury, and especially those associated with endotoxic shock. The non toxic tellurium compound ammonium tri-chloro(dioxoethylene-O,O'-tellurate, AS101, has been recently shown to exert profound anti-inflammatory properties in animal models, associated with its Te(IV redox chemistry. This study explores the anti-inflammatory properties of AS101 with respect to modulation of inflammatory cytokines production and regulation of iNOS transcription and expression in activated macrophages via targeting the NFkB complex. Results AS101 decreased production of IL-6 and in parallel down-regulated LPS-induced iNOS expression and NO secretion by macrophages. AS101 reduced IkB phosphorylation and degradation, and reduced NFkB nuclear translocalization, albeit these effects were exerted at different kinetics. Chromatin immunoprecipitation assays showed that AS101 treatment attenuated p50-subunit ability to bind DNA at the NFkB consensus site in the iNOS promotor following LPS induction. Conclusions Besides AS101, the investigation of therapeutic activities of other tellurium(IV compounds is scarce in the literature, although tellurium is the fourth most abundant trace element in the human body. Since IKK and NFkB may be regulated by thiol modifications, we may thus envisage, inview of our integrated results, that Te(IV compounds, may have important roles in thiol redox biological activity in the human body and represent a new class of anti-inflammatory compounds.

Determination of spins and radioactive widths of tellurium nuclear levels with capturre gamma rays

International Nuclear Information System (INIS)

Bianchini, F.G.

1973-01-01

Spins and levels widths of the tellurium, mainly 128 Te and 130 Te, were determinated by gamma spectroscopy. Measurements of inelastic and elastic scattering, angular distribution and scattering temperature dependence, were still made. Energy levels of this isotopes, were also determinated [pt

Selenium and tellurium nanomaterials

Science.gov (United States)

Piacenza, Elena; Presentato, Alessandro; Zonaro, Emanuele; Lampis, Silvia; Vallini, Giovanni; Turner, Raymond J.

2018-04-01

Over the last 40 years, the rapid and exponential growth of nanotechnology led to the development of various synthesis methodologies to generate nanomaterials different in size, shape and composition to be applied in various fields. In particular, nanostructures composed of Selenium (Se) or Tellurium (Te) have attracted increasing interest, due to their intermediate nature between metallic and non-metallic elements, being defined as metalloids. Indeed, this key shared feature of Se and Te allows us the use of their compounds in a variety of applications fields, such as for manufacturing photocells, photographic exposure meters, piezoelectric devices, and thermoelectric materials, to name a few. Considering also that the chemical-physical properties of elements result to be much more emphasized when they are assembled at the nanoscale range, huge efforts have been made to develop highly effective synthesis methods to generate Se- or Te-nanomaterials. In this context, the present book chapter will explore the most used chemical and/or physical methods exploited to generate different morphologies of metalloid-nanostructures, focusing also the attention on the major advantages, drawbacks as well as the safety related to these synthetic procedures.

Deposition of tellurium films by decomposition of electrochemically-generated H{sub 2}Te: application to radiative cooling devices

Energy Technology Data Exchange (ETDEWEB)

Engelhard, T.; Jones, E.D.; Viney, I. [Coventry Univ. (United Kingdom). Centre for Data Storage Mater.; Mastai, Y.; Hodes, G. [Department of Materials and Interfaces, Weizmann Institute of Science, 76100, Rehovot (Israel)

2000-07-17

The preparation of homogenous, large area thin layers of tellurium on thin polyethylene foils is described. The tellurium was formed by room temperature decomposition of electrochemically generated H{sub 2}Te. Pre-treatment of the polyethylene substrates with KMnO{sub 4} to give a Mn-oxide layer was found to improve the Te adhesion and homogeneity. Optical characterization of the layers was performed using UV/VIS/NIR spectroscopy. Such coatings have favorable characteristics for use as solar radiation shields in radiative cooling devices. The simplicity of generation of the very unstable H{sub 2}Te was also exploited to demonstrate formation of size-quantized CdTe nanocrystals. (orig.)

NMR spectroscopy of organic compounds of selenium and tellurium. Communication 8. Constants of spin-spin interaction of /sup 125/Te-/sup 1/o/sup 3/C in nmr spectra of unsaturated organtellurides

Energy Technology Data Exchange (ETDEWEB)

Kalabin, G.A.; Kushnarev, D.F.; Valeev, R.B. (Irkutskij Gosudarstvennyj Univ. (USSR))

1981-06-01

On the basis of /sup 13/C NMR spectra of a series of unsaturated and aromatic tellurium compounds the constants of spin-spin interaction (SSIC) (sup(1.2)J(Te, C)) are measured. A reliable linear relation between /sup 1/J(Te, C) and s-character of a carbon orbitale forming bond with tellurium is found. Correlation of straight SSIC of carbon with selenium and tellurium in isological compounds is established.

A new tellurium-containing amphiphilic molecule induces apoptosis in HCT116 colon cancer cells.

Science.gov (United States)

Du, Peng; Saidu, Nathaniel Edward Bennett; Intemann, Johanna; Jacob, Claus; Montenarh, Mathias

2014-06-01

Chalcogen-based redox modulators over the years have attracted considerable attention as anti-cancer agents. New selenium- and tellurium-containing compounds with a polar head group and aryl-groups of various lengths have recently been reported as biologically active in several organisms. In the present study, we used the most active of the tellurium compound DP41, and its selenium counterpart DP31 to investigate their effects on the human cancer cell line HCT116. Cells were treated with DP41 or DP31 and the formation of superoxide radicals was determined using dihydroethidium. Cell cycle analysis and apoptosis was determined by cytofluorimetry. Proteins involved in ER signaling and apoptosis were determined by Western blot analysis and fluorescence microscopy. With 50μM of DP41, we observed an increase in O2(-) formation. There was, however, no such increase in O2(-) after treatment with the corresponding selenium compound under the same conditions. In the case of DP41, the production of O2(-) radicals was followed by an up-regulation of Nrf2, HO-1, phospho-eIF2α and ATF4. CHOP was also induced and cells entered apoptosis. Unlike the cancer cells, normal retinal epithelial ARPE-19 cells did not produce elevated levels of O2(-) radicals nor did they induce the ER signaling pathway or apoptosis. The tellurium-containing compound DP41, in contrast to the corresponding selenium compound, induces O2(-) radical formation and oxidative and ER stress responses, including CHOP activation and finally apoptosis. These results indicate that DP41 is a redox modulating agent with promising anti-cancer potentials. Copyright © 2014 Elsevier B.V. All rights reserved.

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

International Nuclear Information System (INIS)

Mal, Joyabrata; Nancharaiah, Yarlagadda V.; Maheshwari, Neeraj; Hullebusch, Eric D. van; Lens, Piet N.L.

2017-01-01

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO 3 2− ) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L −1 d −1 . After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO 3 2− L −1 for 42 d before increasing the influent concentration to 20 mg TeO 3 2− L −1 . Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L −1 ) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Synthesis and structure of aromatic and heterocyclic compounds of tellurium

International Nuclear Information System (INIS)

Sadekov, I.D.; Maksimenko, A.A.; Rivkin, B.B.

1983-01-01

A new universal method of preparing assymmetric and symmetric diaryl-tellurium chlorides and-dibromides, based on the interaction of diarylditellurides with cations of aryl-diazonium in the presence of copper (2) halogenides is developed. High yields of diaryltellium dihalogenices (60-90 de %), the possibility of the a wide variation of the nature of substituents in both components make this reaction one of the most general methods of preparing assymmetric diaryltellurium dihalogenides. It is advisable to use aryldiazonium boron fluorides instead of halogenides in this reaction

Characterization of tellurium-based films for NO2 detection

International Nuclear Information System (INIS)

Tsiulyanu, D.; Tsiulyanu, A.; Liess, H.-D.; Eisele, I.

2005-01-01

Sensing characteristics of tellurium-based thin films for NO 2 monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO 2 with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO 2 sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms

Tellurium adsorption on tungsten and molybdenum field emitters

International Nuclear Information System (INIS)

Collins, R.A.; Kiwanga, C.A.

1977-01-01

Studies of the adsorption of tellurium onto tungsten and molybdenum field emitters are described and the results obtained are compared with those obtained in previous work on the adsorption of silicon and selenium. The adsorption of Te onto W was found to be much more uniform than in the case of Se. Although Te is metallic in many of its properties its adsorptive behavior on field emitters is found to be similar to that of selenium and these adsorptive properties are basically common to all semiconductors. The most evident property of these adsorbates is that the work function and emission current decrease simultaneously at coverages of less than half a monolayer and the work function subsequently increases. (B.D.)

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

Energy Technology Data Exchange (ETDEWEB)

Forootanfar, Hamid [Herbal and Traditional Medicines Research Center, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Amirpour-Rostami, Sahar; Jafari, Mandana [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Forootanfar, Amir [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of); Yousefizadeh, Zahra [The Student Research Committee, Faculty of Pharmacy, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Shakibaie, Mojtaba, E-mail: shakiba@kmu.ac.ir [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of)

2015-04-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K{sub 2}TeO{sub 3}. - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K{sub 2}TeO{sub 3}.

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

International Nuclear Information System (INIS)

Forootanfar, Hamid; Amirpour-Rostami, Sahar; Jafari, Mandana; Forootanfar, Amir; Yousefizadeh, Zahra; Shakibaie, Mojtaba

2015-01-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K 2 TeO 3 . - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K 2 TeO 3

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

Energy Technology Data Exchange (ETDEWEB)

Mal, Joyabrata, E-mail: joyabrata2006@gmail.com [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Nancharaiah, Yarlagadda V. [Biofouling and Biofilm Processes Section, Water and Steam Chemistry Division, Bhabha Atomic Research Centre, Kalpakkam, 603102, Tamil Nadu (India); Homi Bhabha National Institute, Anushakti Nagar Complex, Mumbai 400094 (India); Maheshwari, Neeraj [CNRS UMR 7338, BMBI University de Technologie Compiegne, 60200 Compiegne (France); Hullebusch, Eric D. van [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Université Paris-Est, Laboratoire Géomatériaux et Environnement (LGE), EA 4508, UPEM, 77454, Marne-la-Vallée (France); Lens, Piet N.L. [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Department of Chemistry and Bioengineering, Tampere University of Technology, P.O-Box 541, Tampere (Finland)

2017-04-05

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO{sub 3}{sup 2−}) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L{sup −1} d{sup −1}. After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO{sub 3}{sup 2−} L{sup −1} for 42 d before increasing the influent concentration to 20 mg TeO{sub 3}{sup 2−} L{sup −1}. Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L{sup −1}) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Surface studies on graphite furnace platforms covered with Pd, Rh and Ir as modifiers in graphite furnace atomic absorption spectrometry of tellurium

Energy Technology Data Exchange (ETDEWEB)

Pedro, Juana [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Stripekis, Jorge [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina); Departamento de Ingeniería Química, Instituto Tecnológico de Buenos Aires, Av. Eduardo Madero 399 (1106), Buenos Aires (Argentina); Bonivardi, Adrian [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Tudino, Mabel, E-mail: tudino@qi.fcen.uba.ar [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina)

2015-05-01

The main objective of this work is the study of correlations between the efficiency of the distribution of the permanent platinum group modifiers Pd, Rh and Ir over the graphite surface with the aim of improving analytical signal of tellurium. Modifier solution was deposited onto the platform and pyrolysed after drying. In the case of Pd, the physical vaporization/deposition technique was also tested. In order to analyze the differences amongst coverings (morphology, topology and distribution), the graphite surfaces were studied with scanning electron microscopy and energy dispersive X-ray microscopy. Micrographs for physical vaporization and pyrolytic deposition of Pd were also analyzed in order to explain the lack of signal obtained for tellurium with the first alternative. Similar micrographs were obtained for pyrolytic deposition of Ir and Rh and then, compared to those of Pd. Ir showed the most homogeneous distribution on the graphite surface and the tallest and sharpest transient. With the aim of improving the analytical signal of tellurium, the correlation between the surface studies and the tellurium transient signal (height, area and shape) is discussed. - Highlights: • Distribution of Rh, Pd and Ir onto graphite furnaces is evaluated by SEM and EDX • Micrographs and spectra showed that surface distribution could influence Te signal. • Ir showed the best signal together with the most homogeneous surface distribution. • Pd-PVD micrographs revealed the absence of graphite and no signal for Te.

Tellurium labeled analogues of the fatty acid hexadecenoic acid for imaging of myocardial tissue

International Nuclear Information System (INIS)

Mills, S.L.

1980-01-01

Non-invasive nuclear diagnostic procedures for the evaluation of acute myocardial infarction and ischemia are currently limited by problems associated with the availablity of radiopharmaceuticals, development of imaging equipment, and inherent characteristics of radionuclides. Myocardial tissue requires high levels of substrates which provide energy for the continuous functioning of this vital organ. Of the major sources of energy, the most utilized source is fatty acids. Tellurium-123m, with excellent gamma imaging characteristics was chosen as the radionuclide. A 16 carbon fatty acid, hexadecenoic acid, was chosen as the carrier molecule. The tellurium-123m fatty acid radiopharmaceuticals were formulated either in a solution of 20 percent ethanol, two percent polysorbate 80, and brought to volume with normal saline or in 12.5 percent human serum ablumin and brought to volume with normal saline. Biodistribution was performed in three animal species: Sprague-Dawley rats (three rats per time frame), Australian white rabbits (three rabbits per time frame), and mongrel dogs (one dog per time frame). Dosimetry calculations were performed to assess the radiation dose

Improved selectivity for Pb(II) by sulfur, selenium and tellurium analogues of 1,8-anthraquinone-18-crown-5: synthesis, spectroscopy, X-ray crystallography and computational studies.

Science.gov (United States)

Mariappan, Kadarkaraisamy; Alaparthi, Madhubabu; Hoffman, Mariah; Rama, Myriam Alcantar; Balasubramanian, Vinothini; John, Danielle M; Sykes, Andrew G

2015-07-14

We report here a series of heteroatom-substituted macrocycles containing an anthraquinone moiety as a fluorescent signaling unit and a cyclic polyheteroether chain as the receptor. Sulfur, selenium, and tellurium derivatives of 1,8-anthraquinone-18-crown-5 (1) were synthesized by reacting sodium sulfide (Na2S), sodium selenide (Na2Se) and sodium telluride (Na2Te) with 1,8-bis(2-bromoethylethyleneoxy)anthracene-9,10-dione in a 1 : 1 ratio. The optical properties of the new compounds are examined and the sulfur and selenium analogues produce an intense green emission enhancement upon association with Pb(II) in acetonitrile. Selectivity for Pb(II) is markedly improved as compared to the oxygen analogue 1 which was also competitive for Ca(II) ion. UV-Visible and luminescence titrations reveal that 2 and 3 form 1 : 1 complexes with Pb(II), confirmed by single-crystal X-ray studies where Pb(II) is complexed within the macrocycle through coordinate covalent bonds to neighboring carbonyl, ether and heteroether donor atoms. Cyclic voltammetry of 2-8 showed classical, irreversible oxidation potentials for sulfur, selenium and tellurium heteroethers in addition to two one-electron reductions for the anthraquinone carbonyl groups. DFT calculations were also conducted on 1, 2, 3, 6, 6 + Pb(II) and 6 + Mg(II) to determine the trend in energies of the HOMO and the LUMO levels along the series.

Tellurium quantum dots: Preparation and optical properties

Science.gov (United States)

Lu, Chaoyu; Li, Xueming; Tang, Libin; Lai, Sin Ki; Rogée, Lukas; Teng, Kar Seng; Qian, Fuli; Zhou, Liangliang; Lau, Shu Ping

2017-08-01

Herein, we report an effective and simple method for producing Tellurium Quantum dots (TeQDs), zero-dimensional nanomaterials with great prospects for biomedical applications. Their preparation is based on the ultrasonic exfoliation of Te powder dispersed in 1-methyl-2-pyrrolidone. Sonication causes the van der Waals forces between the structural hexagons of Te to break so that the relatively coarse powder breaks down into nanoscale particles. The TeQDs have an average size of about 4 nm. UV-Vis absorption spectra of the TeQDs showed an absorption peak at 288 nm. Photoluminescence excitation (PLE) and photoluminescence (PL) are used to study the optical properties of TeQDs. Both the PLE and PL peaks revealed a linear relationship against the emission and excitation energies, respectively. TeQDs have important potential applications in biological imaging and catalysis as well as optoelectronics.

Continuous reduction of tellurite to recoverable tellurium nanoparticles using an upflow anaerobic sludge bed (UASB) reactor.

Science.gov (United States)

Ramos-Ruiz, Adriana; Sesma-Martin, Juan; Sierra-Alvarez, Reyes; Field, Jim A

2017-01-01

According to the U.S. Department of Energy and the European Union, tellurium is a critical element needed for energy and defense technology. Thus methods are needed to recover tellurium from waste streams. The objectives of this study was to determine the feasibility of utilizing upflow anaerobic sludge bed (UASB) reactors to convert toxic tellurite (Te IV ) oxyanions to non-toxic insoluble elemental tellurium (Te 0 ) nanoparticles (NP) that are amendable to separation from aqueous effluents. The reactors were supplied with ethanol as the electron donating substrate to promote the biological reduction of Te IV . One reactor was additionally amended with the redox mediating flavonoid compound, riboflavin (RF), with the goal of enhancing the bioreduction of Te IV . Its performance was compared to a control reactor lacking RF. The continuous formation of Te 0 NPs using the UASB reactors was found to be feasible and remarkably improved by the addition of RF. The presence of this flavonoid was previously shown to enhance the conversion rate of Te IV by approximately 11-fold. In this study, we demonstrated that this was associated with the added benefit of reducing the toxic impact of Te IV towards the methanogenic consortium in the UASB and thus enabled a 4.7-fold higher conversion rate of the chemical oxygen demand. Taken as a whole, this work demonstrates the potential of a methanogenic granular sludge to be applied as a bioreactor technology producing recoverable Te 0 NPs in a continuous fashion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Potential for improved extraction of tellurium as a byproduct of current copper mining processes

Science.gov (United States)

Hayes, S. M.; Spaleta, K. J.; Skidmore, A. E.

2016-12-01

Tellurium (Te) is classified as a critical element due to its increasing use in high technology applications, low average crustal abundance (3 μg kg-1), and primary source as a byproduct of copper extraction. Although Te can be readily recovered from copper processing, previous studies have estimated a 4 percent extraction efficiency, and few studies have addressed Te behavior during the entire copper extraction process. The goals of the present study are to perform a mass balance examining Te behavior during copper extraction and to connect these observations with mineralogy of Te-bearing phases which are essential first steps in devising ways to optimize Te recovery. Our preliminary mass balance results indicate that less than 3 percent of Te present in copper ore is recovered, with particularly high losses during initial concentration of copper ore minerals by flotation. Tellurium is present in the ore in telluride minerals (e.g., Bi-Te-S phases, altaite, and Ag-S-Se-Te phases identified using electron microprobe) with limited substitution into sulfide minerals (possibly 10 mg kg-1 Te in bulk pyrite and chalcopyrite). This work has also identified Te accumulation in solid-phase intermediate extraction products that could be further processed to recover Te, including smelter dusts (158 mg kg-1) and pressed anode slimes (2.7 percent by mass). In both the smelter dusts and anode slimes, X-ray absorption spectroscopy indicates that about two thirds of the Te is present as reduced tellurides. In anode slimes, electron microscopy shows that the remaining Te is present in an oxidized form in a complex Te-bearing oxidate phase also containing Pb, Cu, Ag, As, Sb, and S. These results clearly indicate that more efficient, increased recovery of Te may be possible, likely at minimal expense from operating copper processing operations, thereby providing more Te for manufacturing of products such as inexpensive high-efficiency solar panels.

Characterization of tellurium-based films for NO{sub 2} detection

Energy Technology Data Exchange (ETDEWEB)

Tsiulyanu, D. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of)]. E-mail: tsiu@cni.md; Tsiulyanu, A. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of); Liess, H.-D. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany); Eisele, I. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany)

2005-08-01

Sensing characteristics of tellurium-based thin films for NO{sub 2} monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO{sub 2} with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO{sub 2} sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms.

Strong nonlinear photonic responses from microbiologically synthesized tellurium nanocomposites

Science.gov (United States)

Liao, K.-S.; Wang, Jingyuan; Dias, S.; Dewald, J.; Alley, N.J.; Baesman, S.M.; Oremland, R.S.; Blau, W.J.; Curran, S.A.

2010-01-01

A new class of nanomaterials, namely microbiologically-formed nanorods composed of elemental tellurium [Te(0)] that forms unusual nanocomposites when combined with poly(m-phenylenevinylene-co-2,5-dioctoxy-phenylenevinylene) (PmPV) is described. These bio-nanocomposites exhibit excellent broadband optical limiting at 532 and 1064 nm. Nonlinear scattering, originating from the laser induced solvent bubbles and microplasmas, is responsible for this nonlinear behavior. The use of bacterially-formed Te(0) when combined with an organic chemical host (e.g., PmPV) is a new green method of nanoparticle syntheses. This opens the possibilities of using unique, biologically synthesized materials to advance future nanoelectronic and nanophotonic applications. ?? 2009 Elsevier B.V. All rights reserved.

Extraction-spectrophotometric method for silicon determination in high-purity substances. 1. Silicon determination in tellurium

Energy Technology Data Exchange (ETDEWEB)

Shaburova, V P; Yudelevich, I G [AN SSSR, Novosibirsk (USSR). Inst. Neorganicheskoj Khimii

1989-01-01

The extraction-spectrophotometric method for silicon determination in tellurium based on extraction isolation of the base by tributyl phosphate from hydrochloride solutions and with addition of HNO/sub 3/ and spectrophotometric silicon determination using malachite green is developed. The method permits to determine 2x10/sup -1/-3x10/sup -4/ % Si.

The use of masking agents in the determination, by hydride generation and atomic-absorption spectrophotometry, of arsenic, antimony, selenium, tellurium, and bismuth in the presence of noble metals

International Nuclear Information System (INIS)

Kellerman, S.P.

1982-01-01

The effectiveness of thiosemicarbazide, tellurium, and potassium iodide as masking agents to eliminate interferences was assessed. Thiosemicarbazide was found to be effective in eliminating or reducing the interferences on arsenic, antimony, and bismuth, and tellurium reduced the interferences on selenium. The interferences on tellurium could not be eliminated. Arsenic, antimony, selenium, and bismuth were determined in metal sulphide concentrates that were spiked with the noble metals (defined here as gold plus all the platinum-group metals except osmium). The relative standard deviations for arsenic, antimony, bismuth, and selenium were 0,061, 0,017, 0,029, and 0,145 respectively. The values obtained for all the analytes agreed favourably with the preferred values for two in-house reference samples. The laboratory method is detailed in an appendix

Improvement of physical properties of ZnO thin films by tellurium doping

Energy Technology Data Exchange (ETDEWEB)

Sönmezoğlu, Savaş, E-mail: svssonmezoglu@kmu.edu.tr; Akman, Erdi

2014-11-01

Highlights: • We report the synthesis of tellurium-doped zinc oxide (Te–ZnO) thin films using sol–gel method. • Highly c-axis oriented Te-doped ZnO thin films were grown on FTO glasses as substrate. • 1.5% Te-doping ratio could improve the physical properties of ZnO thin films. - Abstract: This investigation addressed the structural, optical and morphological properties of tellurium incorporated zinc oxide (Te–ZnO) thin films. The obtained results indicated that Te-doped ZnO thin films exhibit an enhancement of band gap energy and crystallinity compared with non-doped films. The optical transmission spectra revealed a shift in the absorption edge toward lower wavelengths. X-ray diffraction measurement demonstrated that the film was crystallized in the hexagonal (wurtzite) phase and presented a preferential orientation along the c-axis. The XRD obtained patterns indicate that the crystallite size of the thin films, ranging from 23.9 to 49.1 nm, changed with the Te doping level. The scanning electron microscopy and atomic force microscopy results demonstrated that the grain size and surface roughness of the thin films increased as the Te concentration increased. Most significantly, we demonstrate that it is possible to control the structural, optical and morphological properties of ZnO thin films with the isoelectronic Te-incorporation level.

High performance supercapacitor and non-enzymatic hydrogen peroxide sensor based on tellurium nanoparticles

Directory of Open Access Journals (Sweden)

M. Manikandan

2017-04-01

Full Text Available Tellurium nanoparticles (Te Nps were synthesized by wet chemical method and characterized by XRD, Raman, FESEM, TEM, XPS, UV–Vis and FL. The Nps were coated on graphite foil and Glassy carbon electrode to prepare the electrodes for supercapacitor and biosensor applications. The supercapacitor performance is evaluated in 2 M KOH electrolyte by both Cyclic Voltammetry (CV and galvanostatic charge-discharge method. From charge-discharge method, Te Nps show a specific capacitance of 586 F/g at 2 mA/cm2 and 100 F/g at 30 mA/cm2 as well as an excellent cycle life (100% after 1000 cycles. In addition, the H2O2 sensor performance of Te Nps modified glassy carbon electrode is checked by CV and Chronoamperometry (CA in phosphate buffer solution (PBS. In the linear range of 0.67 to 8.04 μM of hydrogen peroxide (H2O2, Te NPs show a high sensitivity of 0.83 mA mM−1 cm−2 with a correlation coefficient of 0.995. The detection limit is 0.3 μM with a response time less than 5 s. Keywords: Tellurium nanoparticles, Supercapacitor, Biosensor, Hydrogen peroxide

Intrinsic two-dimensional states on the pristine surface of tellurium

Science.gov (United States)

Li, Pengke; Appelbaum, Ian

2018-05-01

Atomic chains configured in a helical geometry have fascinating properties, including phases hosting localized bound states in their electronic structure. We show how the zero-dimensional state—bound to the edge of a single one-dimensional helical chain of tellurium atoms—evolves into two-dimensional bands on the c -axis surface of the three-dimensional trigonal bulk. We give an effective Hamiltonian description of its dispersion in k space by exploiting confinement to a virtual bilayer, and elaborate on the diminished role of spin-orbit coupling. These intrinsic gap-penetrating surface bands were neglected in the interpretation of seminal experiments, where two-dimensional transport was otherwise attributed to extrinsic accumulation layers.

Tellurium Enrichment in Jurassic Coal, Brora, Scotland

Directory of Open Access Journals (Sweden)

Liam Bullock

2017-11-01

Full Text Available Mid-Jurassic pyritic coals exposed at the village of Brora, northern Scotland, UK, contain a marked enrichment of tellurium (Te relative to crustal mean, average world coal compositions and British Isles Carboniferous coals. The Te content of Brora coal pyrite is more than one order of magnitude higher than in sampled pyrite of Carboniferous coals. The Te enrichment coincides with selenium (Se and mercury (Hg enrichment in the rims of pyrite, and Se/Te is much lower than in pyrites of Carboniferous coals. Initial pyrite formation is attributed to early burial (syn-diagenesis, with incorporation of Te, Se, Hg and lead (Pb during later pyrite formation. The source of Te may have been a local hydrothermal system which was responsible for alluvial gold (Au in the region, with some Au in Brora headwaters occurring as tellurides. Anomalous Te is not ubiquitous in coal, but may occur locally, and is detectable by laser ablation inductively coupled plasma-mass spectrometry (LA-ICP-MS.

Effect of tellurium on viscosity and liquid structure of GaSb melts

Energy Technology Data Exchange (ETDEWEB)

Ji Leilei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China); Geng Haoran [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)], E-mail: mse_genghr@ujn.edu.cn; Sun Chunjing [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Teng Xinying; Liu Yamei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)

2008-04-03

The behavior of GaSb melt with tellurium addition was investigated using viscometer and differential scanning calorimetry (DSC). Normally, the viscosity of all melts measured decreased with the increasing temperature. However, anomalous transition points were observed in the temperature dependence of viscosity for Ga-Sb-Te system. Corresponded with the abnormal points on the viscosity-temperature curves, there were thermal effect peaks on the DSC curves. Furthermore, viscous activation energy and flow units of these melts and their structural features were discussed in this paper.

Ecological aspects of selenium and tellurium in human and animal health

Energy Technology Data Exchange (ETDEWEB)

Frost, D V; Ingvoldstad, D

1975-01-01

Animal and human studies indicate that selenium inadequacy, in part, underlies various chronic diseases. Epidemiologic evidence suggests that cancer and heart disease are most common where ambient Se availability is low. Plant Se uptake and Se blood levels are inverse to human cancer mortality. As the active group in glutathione peroxidase, Se/sup -2/ inhibits aberrant oxidations which lead to chronic diseases. It binds heavy metals, and with tocopherol maintains tissue integrity. Sulfur dioxide fallout from the atmosphere, resulting from fossil fuel burning, may diminish the nutritional availability of selenium by diminishing plant uptake. Intensive ruminant grazing returns unavailable Se/sup 0/ to soils. Trimethyl selenium ion, as excreted by animals, also appears to be unavailable to plants. Modern fertilization practices and the effect of buildup of sulfates in the soil, due to acid rains, both appear to lessen the availability of Se to plants. SeO/sub 2/ added to the atmosphere from combustion and volcanic activity react with SO/sub 2/ to yield Se/sup 0/. This is presumed to fall out as particles from the air. How traces of Se are otherwise carried in air, explaining its enrichment in some areas, is unknown. The New Zealand experience with Se inadequacy in animals and man may be repeated in other parts of the world. Se inadequacy is far more of a human health problem than Se toxicity. There are no known adverse health effects from tellurium, other than tellurium breath. 164 references, 5 figures, 3 tables.

Synthesis of Novel E-2-Chlorovinyltellurium Compounds Based on the Stereospecific Anti-addition of Tellurium Tetrachloride to Acetylene

Directory of Open Access Journals (Sweden)

Svetlana V. Amosova

2012-05-01

Full Text Available The reaction of tellurium tetrachloride with acetylene proceeds in a stereospecific anti-addition manner to afford the novel products E-2-chlorovinyltellurium trichloride and E,E-bis(2-chlorovinyltellurium dichloride. Reaction conditions for the selective preparation of each of these products were found. The latter was obtained in 90% yield in CHCl₃ under a pressure of acetylene of 10–15 atm, whereas the former product was formed in up to 72% yield in CCl₄ under a pressure of acetylene of 1–3 atm. Synthesis of the previously unknown E,E-bis(2-chlorovinyl telluride, E,E-bis(2-chlorovinyl ditelluride, E-2-chlorovinyl 1,2,2-trichloroethyl telluride and E,E-bis(2-chlorovinyl-tellurium dibromide is described.

The application of three-phase liquid-liquid extraction to the analysis of bismuth and tellurium in sulphide concentrates

International Nuclear Information System (INIS)

Nicholas, D.J.

1976-01-01

An extraction system consisting of one aqueous and two organic phases is described. Diantipyrylmethane (DAM) is used as the extractant for bismuth and tellurium, which are extracted into the smaller of the two organic phases from nitric acid and perchloric acid respectively. The extraction efficiency is in the range of 90 to 95 per cent, compensation for incomplete extraction being made by the technique of standard addition. Copper, lead, and zinc are not extracted in either procedure. When the solutions contain high concentrations of iron, thioglycolic acid is used as a masking agent for iron in the extraction of bismuth. Atomic-absorption spectrophotometry is used for the analysis of the third phase after it has been diluted with methanol. The precision for bismuth and tellurium is in the range of 3 to 4 per cent. The accuracy, as ascertained from comparative analyses of sulphide concentrates, is good

Tellurium stable isotope fractionation in chondritic meteorites and some terrestrial samples

Science.gov (United States)

Fehr, Manuela A.; Hammond, Samantha J.; Parkinson, Ian J.

2018-02-01

New methodologies employing a 125Te-128Te double-spike were developed and applied to obtain high precision mass-dependent tellurium stable isotope data for chondritic meteorites and some terrestrial samples by multiple-collector inductively coupled plasma mass spectrometry. Analyses of standard solutions produce Te stable isotope data with a long-term reproducibility (2SD) of 0.064‰ for δ130/125Te. Carbonaceous and enstatite chondrites display a range in δ130/125Te of 0.9‰ (0.2‰ amu-1) in their Te stable isotope signature, whereas ordinary chondrites present larger Te stable isotope fractionation, in particular for unequilibrated ordinary chondrites, with an overall variation of 6.3‰ for δ130/125Te (1.3‰ amu-1). Tellurium stable isotope variations in ordinary chondrites display no correlation with Te contents or metamorphic grade. The large Te stable isotope fractionation in ordinary chondrites is likely caused by evaporation and condensation processes during metamorphism in the meteorite parent bodies, as has been suggested for other moderately and highly volatile elements displaying similar isotope fractionation. Alternatively, they might represent a nebular signature or could have been produced during chondrule formation. Enstatite chondrites display slightly more negative δ130/125Te compared to carbonaceous chondrites and equilibrated ordinary chondrites. Small differences in the Te stable isotope composition are also present within carbonaceous chondrites and increase in the order CV-CO-CM-CI. These Te isotope variations within carbonaceous chondrites may be due to mixing of components that have distinct Te isotope signatures reflecting Te stable isotope fractionation in the early solar system or on the parent bodies and potentially small so-far unresolvable nucleosynthetic isotope anomalies of up to 0.27‰. The Te stable isotope data of carbonaceous and enstatite chondrites displays a general correlation with the oxidation state and hence might

The influence of composition of fluoride electrolytes and conditions of the electrodeposition on some properties of tellurium

International Nuclear Information System (INIS)

Bugelis, V.M.; Kum, G.N.; Abrarov, O.A.; Madumarov, A.; Navalikhin, L.V.; Ajnakulov, Eh.B.

1981-01-01

Effect of electrolytic bath content, cathode current density, illumination and temperature on specific resistance, photosensitivity, structure and chemical purity of plated tellurium coatings is studied. Deposition is realized from moderately acid fluoride electrolytes at the constant temperature with a platinum working electrode. X-ray studies of precipitates obtained are carried out

Evaluated phase diagrams of binary metal-tellurium systems of the D-block transition elements

International Nuclear Information System (INIS)

Chattopadhyay, G.; Bharadwaj, S.R.

1989-01-01

The binary phase diagrams of metal-tellurium systems for twenty seven d-block transition elements have been critically evaluated. Complete phase diagrams are presented for the elements, chromium, manganese, iron, cobalt, nickel, copper, molybdenum, palladium, silver, lanthanum, platinum and gold, whereas, for scandium, titanium, vanadium, yttrium, zirconium, niobium, technitium, ruthenium, rhodium, hafnium, tantalum, tungsten , rhenium, osmium and iridium, the phase diagrams are incomplete and tentative. (author). 20 refs., 27 tabs., 27 figs

Thermodynamic assessment of the palladium-tellurium (Pd-Te) system

International Nuclear Information System (INIS)

Gosse, S.; Gueneau, C.

2011-01-01

Among the fission products formed in nuclear fuels, the platinum-group metal palladium and the chalcogen element tellurium exhibit strong interaction. It is therefore of interest to be able to predict the chemical equilibria involving the Pd and Te fission products. A thermodynamic assessment is carried out using the Calphad (Calculation of Phase Diagram) method to investigate the behaviour of Pd-Te alloy system in nuclear fuels under irradiation and under waste disposal conditions. The Pd-Te binary description was optimized using experimental data found in literature including thermodynamic properties and phase diagram data. To validate the calculated phase diagram and thermodynamic properties, the results are compared with data from the literature. Both calculated and experimental phase diagrams and thermodynamic properties are in good agreement in the whole Pd-Te composition range. (authors)

Investigation of evaporation characteristics of polonium and its lighter homologues selenium and tellurium from liquid Pb-Bi-eutecticum

CERN Document Server

Neuhausen, J; Eichler, B

2004-01-01

The evaporation behaviour of polonium and its lighter homologues selenium and tellurium dissolved in liquid Pb-Bi-eutecticum (LBE) has been studied at various temperatures in the range from 482 K up to 1330 K under Ar/H2 and Ar/H2O-atmospheres using γ-ray spectroscopy. Polonium release in the temperature range of interest for technical applications is slow. Within short term (1h) experiments measurable amounts of polonium are evaporated only at temperatures above 973 K. Long term experiments reveal that a slow evaporation of polonium occurs at temperatures around 873 K resulting in a fractional polonium loss of the melt around 1% per day. Evaporation rates of selenium and tellurium are smaller than those of polonium. The presence of H2O does not enhance the evaporation within the error limits of our experiments. The thermodynamics and possible reaction pathways involved in polonium release from LBE are discussed.

Effect of sample preparation methods on photometric determination of the tellurium and cobalt content in the samples of copper concentrates

Directory of Open Access Journals (Sweden)

Viktoriya Butenko

2016-03-01

Full Text Available Methods of determination of cobalt and nickel in copper concentrates currently used in factory laboratories are very labor intensive and time consuming. The limiting stage of the analysis is preliminary chemical sample preparation. Carrying out the decomposition process of industrial samples with concentrated mineral acids in open systems does not allow to improve the metrological characteristics of the methods, for this reason improvement the methods of sample preparation is quite relevant and has a practical interest. The work was dedicated to the determination of the optimal conditions of preliminary chemical preparation of copper concentrate samples for the subsequent determination of cobalt and tellurium in the obtained solution using tellurium-spectrophotometric method. Decomposition of the samples was carried out by acid dissolving in individual mineral acids and their mixtures by heating in an open system as well as by using ultrasonification and microwave radiation in a closed system. In order to select the optimal conditions for the decomposition of the samples in a closed system the phase contact time and ultrasonic generator’s power were varied. Intensification of the processes of decomposition of copper concentrates with nitric acid (1:1, ultrasound and microwave radiation allowed to transfer quantitatively cobalt and tellurium into solution spending 20 and 30 min respectively. This reduced the amount of reactants used and improved the accuracy of determination by running the process in strictly identical conditions.

LIGHT INDUCED TELLURIUM ENRICHMENT ON CDZNTE CRYSTAL SURFACES DETECTED BY RAMAN SPECTROSCOPY

International Nuclear Information System (INIS)

Hawkins, S; Eliel Villa-Aleman, E; Martine Duff, M; Douglas Hunter, D

2007-01-01

Synthetic CdZnTe or 'CZT' crystals can be grown under controlled conditions to produce high quality crystals to be used as room temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro Raman spectroscopy. The growth of Te rich areas on the surface was induced by low powered lasers. The growth was observed versus time with low power Raman scattering and was observed immediately under higher power conditions. The detector response was also measured after induced Te enrichment

Equilibrium evaporation test of lead-bismuth eutectic and of tellurium in lead-bismuth

International Nuclear Information System (INIS)

Ohno, Shuji; Nishimura, Masahiro; Hamada, Hirotsugu; Miyahara, Shinya; Sasa, Toshinobu; Kurata, Yuji

2005-01-01

A series of equilibrium evaporation experiment was performed to acquire the essential and the fundamental knowledge about the transfer behavior of lead-bismuth eutectic (LBE) and impurity tellurium in LBE from liquid to gas phase. The experiments were conducted using the transpiration method in which saturated vapor in an isothermal evaporation pot was transported by inert carrier gas and collected outside of the pot. The size of the used evaporation pot is 8 cm inner diameter and 15 cm length. The weight of the LBE pool in the pot is about 500 g. The investigated temperature range was 450degC to 750degC. From this experiment and discussion using the data in literature, we have obtained several instructive and useful data on the LBE evaporation behavior such as saturated vapor pressure of LBE, vapor concentration of Pb, Bi and Bi 2 in LBE saturated gas phase, and activity coefficient of Pb in the LBE. The LBE vapor pressure equation is represented as the sum of Pb, Bi and Bi 2 vapor in the temperature range between 550degC and 750degC as logP[Pa]=10.2-10100/T[k]. The gas-liquid equilibrium partition coefficient of tellurium in LBE is in the range of 10 to 100, with no remarkable temperature dependency between 450degC and 750degC. This research was founded by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). (author)

Facile Hydrothermal Synthesis of Tellurium Nanostructures for Solar Cells

Directory of Open Access Journals (Sweden)

M. Panahi-Kalamuei

2014-10-01

Full Text Available Tellurium (Te nanostructures have been successfully synthesized via a simple hydrothermal methodfrom the reaction of a TeCl4 aqueous solution with thioglycolic acid (TGA as a reductant. TGA can be easily oxidized to the corresponding disulfide [SCH2CO2H]2, which in turn can reduce TeCl4 to Te. The obtained Te was characterized by XRD, SEM, EDS, and DRS. The effect of reducing agent on morphology and size of the products were also studied. Additionally, Te thin film was deposited on the FTO-TiO2 by Dr- blading then employed to solar cell application and measured open circuit voltage (Voc, short circuit current (Isc, and fill factor (FF were determined as well. The studies showed that particle morphology and sizes play crucial role on solar cell efficiencies.

Separation of 99Mo from 132Te using thiourea as complexing agent. Application to the separation of 99Mo from the fission products

International Nuclear Information System (INIS)

Mestnik, S.A.C.

1987-01-01

A radiochemical method to isolate 99 Mo from 132 Te both produced in the fission of 235 U has been developed. The method is based on the formation of a cationic complex of tellurium with thiourea in acid medium wich is retained (98.7+-0.5) % on a cation exchange resin (Dowex 50W-X8, 100-200 mesh) wile (99.8+-0.05)% 99 Mo passes through it, due to the non formation of such complex in the same experimental conditions. The radiochemical purity of the separated 99 Mo verified by using gamma spectrometry was found to be suitable for the preparation of 99 Mo- 99m Tc generators. The retention of 99 Mo on an alumina column as function of pH was investigated. The best pH range for this purpose was found to be between 4.0-4.5. Yellow crystals with melting point of 115 0 C were formed when non-irradiated tellurium reacted with thiourea. Elemental analysis, ultra-violet and infra-red absorption spectrophotometry as well as thermogravimetry were used to characterize the complex formed. In the studies made in order to characterize the compound it has been observed: 1. the most probable chemical composition of the complex studied is [Te(SCN 2 H 4 ) 4 ] (SO 4 ) 2 ; 2. the coordination takes place between tellurium and sulphur atoms; 3. the maximum absorption in the ultra-violet region occurs near 310nm. The thermogravimetric curves obtained allowed to propose the concerned thermodecomposition mechanism. (author) [pt

Determination of gold, indium, tellurium and thallium in the same sample digest of geological materials by atomic-absorption spectroscopy and two-step solvent extraction

Science.gov (United States)

Hubert, A.E.; Chao, T.T.

1985-01-01

A rock, soil, or stream-sediment sample is decomposed with hydrofluoric acid, aqua regia, and hydrobromic acid-bromine solution. Gold, thallium, indium and tellurium are separated and concentrated from the sample digest by a two-step MIBK extraction at two concentrations of hydrobromic add. Gold and thallium are first extracted from 0.1M hydrobromic acid medium, then indium and tellurium are extracted from 3M hydrobromic acid in the presence of ascorbic acid to eliminate iron interference. The elements are then determined by flame atomic-absorption spectrophotometry. The two-step solvent extraction can also be used in conjunction with electrothermal atomic-absorption methods to lower the detection limits for all four metals in geological materials. ?? 1985.

Evaluation of the Content of Antimony, Arsenic, Bismuth, Selenium, Tellurium and Their Inorganic Forms in Commercially Baby Foods.

Science.gov (United States)

Ruiz-de-Cenzano, M; Rochina-Marco, A; Cervera, M L; de la Guardia, M

2017-12-01

Baby foods, from the Spanish market and prepared from meat, fish, vegetables, cereals, legumes, and fruits, were analyzed to obtain the concentration of antimony (Sb), arsenic (As), bismuth (Bi), and tellurium (Te) as toxic elements and selenium (Se) as essential element. An analytical procedure was employed based on atomic fluorescence spectroscopy which allowed to obtain accurate data at low levels of concentration. Values of 14 commercial samples, expressed in nanograms per gram fresh weight, ranged for Sb 0.66-6.9, As 4.5-242, Te 1.35-2.94, Bi 2.18-4.79, and Se 5.4-109. Additionally, speciation studies were performed based on data from a non-chromatographic screening method. It was concluded that tellurium and bismuth were mainly present as inorganic forms and selenium as organic form, and antimony and arsenic species depend on the ingredients of each baby food. Risk assessment considerations were made by comparing dietary intake of the aforementioned elements through the consumption of one baby food portion a day and recommended or tolerable guideline values.

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

Energy Technology Data Exchange (ETDEWEB)

Simon, F.-G., E-mail: franz-georg.simon@bam.de [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany); Holm, O.; Berger, W. [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany)

2013-04-15

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources.

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

International Nuclear Information System (INIS)

Simon, F.-G.; Holm, O.; Berger, W.

2013-01-01

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources

Determination of tellurium by hydride generation with in situ trapping flame atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Matusiewicz, H.; Krawczyk, M. [Politechn Poznanska, Poznan (Poland)

2007-03-15

The analytical performance of coupled hydride generation - integrated atom trap (HG-IAT) atomizer flame atomic absorption spectrometry (FAAS) system was evaluated for determination of Te in reference material (GBW 07302 Stream Sediment), coal fly ash and garlic. Tellurium, using formation of H{sub 2}Te vapors, is atomized in air-acetylene flame-heated IAT. A new design HG-IAT-FAAS hyphenated technique that would exceed the operational capabilities of existing arrangernents (a water-cooled single silica tube, double-slotted quartz tube or an 'integrated trap') was investigated. An improvement in detection limit was achieved compared with using either of the above atom trapping techniques separately. The concentration detection limit, defined as 3 times the blank standard deviation (3{sigma}), was 0.9 ng mL{sup -1} for Te. For a 2 min in situ preconcentration time (sample volume of 2 mL), sensitivity enhancement compared to flame AAS, was 222 fold, using the hydride generation atom trapping technique. The sensitivity can be further improved by increasing the collection time. The precision, expressed as RSD, was 7.0% (n = 6) for Te. The accuracy of the method was verified using a certified reference material (GBW 07302 Stream Sediment) by aqueous standard calibration curves. The measured Te contents of the reference material was in agreement with the information value. The method was successfully applied to the determination of tellurium in coal fly ash and garlic.

Test of irradiation of tellurium oxide for obtaining iodine-131 by dry distillation

International Nuclear Information System (INIS)

Alanis M, J.

2003-07-01

With the purpose of optimizing to the maximum independently the work of the reactor of those mathematical calculations of irradiation that are already optimized, now it corresponds to carry out irradiation tests in the different positions with their respective neutron fluxes that it counts the reactor for samples irradiation. Then, it is necessary to carry out the irradiation of the tellurium dioxide through cycles, with the purpose of observing the activity that it goes accumulating in each cycle and this way to obtain an activity of the Iodine-131 obtained when finishing the last cycle. (Author)

Formation of defects in tellurium at various levels of gravitation

International Nuclear Information System (INIS)

Parfen'ev, R.V.; Farbshtejn, I.I.; Shul'pina, I.L.; Yakimov, S.V.; Shalimov, V.P.; Turchaninov, A.M.

2002-01-01

One investigated into effect of gravitation conditions during tellurium crystallization (ranging from microgravitation up to increased gravitation - 5g 0 ) on concentration of neutral (N D ) and electrically active (N AD ) acceptor structure defects in specimens grown both under complete remelting of parent ingot and under directed recrystallization of ingot with inoculation. N AD and N D concentrations and their distribution along the specimen depth were determined on the basis of analysis of electrical characteristics (conductivity and the Hall effect) measured along ingots within 1.6-300 K temperature range. The results were compared with characteristics of specimens grown following the similar program under normal conditions. At complete remelting under microgravitation one detected attributes of strong supercooling and spontaneous crystallization, as well as, of specimen resistance oscillation by its depth caused by N D modulation [ru

Use of Iodine-131 to Tellurium-132 Ratios for Assessing the Relationships between Human Inhaled Radioactivity and Environmental Monitoring after the Accident in Fukushima

Directory of Open Access Journals (Sweden)

Koji Uchiyama

2018-03-01

Full Text Available Significant differences in findings were seen between the intake amounts of iodine-131 that were derived from direct measurements and the estimated intake from environmental monitoring data at the Fukushima accident. To clarify these discrepancies, we have investigated the iodine-131 and tellurium-132 body burdens of five human subjects, who after being exposed to a radioactive plume, underwent 21.5 h whole body counter measurements at Fukui Prefectural Hospital, so clear intake scenario and thyroid counter measurement data were available. To determine the iodine-131 and tellurium-132 body burdens, we introduced a new method of whole body counter calibration composed of a self-consistent approach with the time-dependent correction efficiency factors concept. The ratios of iodine-131 to tellurium-132, ranging from 0.96 ± 0.05 to 2.29 ± 0.38, were consistent with results of the environmental measurements. The 24 h iodine uptake values ranging from 12.1–16.0% were within euthyroid range in Japanese people. These results suggest, even if the relatively low thyroid iodine uptake in the Japanese population was taken into consideration, that there is no doubt about the consistency between direct measurements and environmental monitoring data. Adequate intake scenario is suggested to be principally important to estimate the inhaled radioactivity in areas in or around nuclear accidents.

Exploratory studies of element substitutions in synthetic tetrahedrite. Part II. Selenium and tellurium as anions in Zn-Fe tetrahedrites

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

1999-01-01

-free) compositons do not materialize. The substituted Se tetrahedrite coexists with Cu3SbSe3, (iron-bearing) Cu2-xSe, Cu3SbSe4 plus/minus low Zn-sulfide melt. Selenium does not adopt the role of cation and tellurium that of anion in the tetrahedrite structure. The explanation of the severely restricted composition...

The effect of hydrostatic pressure on the anomalous sign reversal of the Hall coefficient in tellurium

International Nuclear Information System (INIS)

Balynas, V.; Dobrovolskis, Z.; Krotkus, A.; Hoerstel, W.

1981-01-01

In order to obtain information about the pressure behaviour of the higher lying second conduction band the dependences of the Hall coefficient of single crystalline tellurium on temperature (300 to 500 K) have been measured at atmospheric pressure and hydrostatic pressures of 500 and 800 MPa. The separation between the two conduction bands in Te decreases with increasing pressure. The anomalous sign reversal of the Hall coefficient can be well explained by a double-conduction band model

Revision and extension to the analysis of the third spectrum of tellurium: Te III

International Nuclear Information System (INIS)

Tauheed, A.; Naz, A.

2011-01-01

The spectrum of doubly ionized tellurium atom (Te III) has been investigated in the vacuum ultraviolet wavelength region. The ground configuration of Te III is 5s 2 5p 2 and the excited configurations are of the type 5s 2 5p nl. The core excitation leads to a 5s5p 3 configuration. Cowan's multi-configuration interaction code was utilized to predict the ion structure. The observed spectrum of tellurium was recorded on a 3-m normal incidence vacuum spectrograph of Antigonish Laboratory (Canada) in the wavelength region of 300 - 2000 A by using a triggered spark light source for the excitation of the spectrum. The 5s 2 5p 2 - [ 5s 2 5p (5d + 6d + 7d + 6s + 7s + 8s) + 5s5p 3 ] transition array has been analyzed. Previously reported levels by Joshi et al have been confirmed while the older analysis by Crooker and Joshi has been revised and extended to include the 5s 2 5p (5d, 6d, 7d, 6s,7s, 8s) and 5s5p 3 configurations. Least-squares- fitted parametric calculations were used to interpret the final results. One hundred and fifty spectral lines have been identified to establish 60 energy levels. Our wavelength accuracy for unblended and sharp lines is better than ±0.005 A. The ionization potential of Te III was found to be 224550 ± 300 cm -1 (27.841 ± 0.037eV).

Validation of a new design of tellurium dioide-irradiated target

Energy Technology Data Exchange (ETDEWEB)

Fllaoui, Aziz; Ghamad, Younes; Zoubir, Brahim; Ayaz, Zinel Abidine; El Morabiti, Aissam; Amayoud, Hafid [Centre National de l' Energie des Sciences et des Techniques Nucleaires, Rabat (Morocco); Chakir, El Mahjoub [Nuclear Physics Department, University Ibn Toufail, Kenitra (Morocco)

2016-10-15

Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO{sub 2}) material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10 - 4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics). To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600 .deg. C with the appearance of deformations on lids beyond 450 .deg. C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes-convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week) at 1.5 MW. The results show that the irradiated targets are

Validation of a New Design of Tellurium Dioxide-Irradiated Target

Directory of Open Access Journals (Sweden)

Aziz Fllaoui

2016-10-01

Full Text Available Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO2 material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10−4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics. To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600°C with the appearance of deformations on lids beyond 450°C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes—convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week at 1.5 MW. The results show that the irradiated targets are

Light-Induced Tellurium Enrichment on CdZnTe Crystal Surfaces Detected by Raman Spectroscopy

International Nuclear Information System (INIS)

Hawkins, Samantha A.; Villa-Aleman, Eliel; Duff, Martine C.; Hunter, Doug B.; Burger, Arnold; Groza, Michael; Buliga, Vladimir; Black, David R.

2008-01-01

CdZnTe (CZT) crystals can be grown under controlled conditions to produce high-quality crystals to be used as room-temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro-Raman spectroscopy. The growth of Te rich areas on the surface was induced by low-power lasers. The growth was observed versus time with low-power Raman scattering and was observed immediately under higher-power conditions. The detector response was also measured after induced Te enrichment.

Tellurium rings as electron pair donors in cluster compounds and coordination polymers; Tellurringe als Elektronenpaardonoren in Clusterverbindungen und Koordinationspolymeren

Energy Technology Data Exchange (ETDEWEB)

Guenther, Anja

2011-11-08

In this dissertation novel and already known molecular tellurium rings are presented in cluster compounds and quasi-one-dimensional coordination polymers. The cyclic, homonuclear units are always stabilized by coordination to electron-rich transition metal atoms, with the coordinating tellurium atoms acting as two-electron donors. As a synthesis route, the solid-state reaction in quartz glass vials was used uniformly. In addition to structural determination, the focus was on the characterization of the resulting compounds. For this purpose, resistance measurements were carried out on selected compounds, the magnetic behavior and the thermal degradation reactions were investigated and accompanying quantum chemical calculations were carried out. [German] In dieser Dissertation werden neuartige sowie bereits bekannte molekulare Tellurringe in Clusterverbindungen und quasi-eindimensionalen Koordinationspolymeren vorgestellt. Die Stabilisierung der zyklischen, homonuklearen Einheiten erfolgt dabei stets durch die Koordination an elektronenreiche Uebergangsmetallatome, wobei die koordinierenden Telluratome gegenueber diesen als Zwei-Elektronendonoren fungieren. Als Syntheseroute wurde dabei einheitlich auf die Festkoerperreaktion in Quarzglasampullen zurueckgegriffen. Neben der Strukturaufklaerung stand die Charakterisierung der erhaltenden Verbindungen im Fokus der Arbeit. Dazu wurden an ausgewaehlten Verbindungen Widerstandsmessungen durchgefuehrt, das magnetische Verhalten sowie die thermischen Abbaureaktionen untersucht und begleitende quantenchemische Rechnungen durchgefuehrt.

Determination of tellurium at ultra-trace levels in drinking water by on-line solid phase extraction coupled to graphite furnace atomic absorption spectrometer

International Nuclear Information System (INIS)

Pedro, Juana; Stripekis, Jorge; Bonivardi, Adrian; Tudino, Mabel

2008-01-01

In this paper, two time-based flow injection (FI) separation pre-concentration systems coupled to graphite furnace atomic absorption spectrometry (GFAAS) for tellurium determination are studied and compared. The first alternative involves the pre-concentration of the analyte onto Dowex 1X8 employed as packaging material of a micro-column inserted in the flow system. The second set-up is based on the co-precipitation of tellurium with La(OH) 3 followed by retention onto XAD resins. Both systems are compared in terms of limit of detection, linear range, RSD%, sample throughput, micro-columns lifetime and aptitude for fully automatic operation. The features of the Dowex system are: 37% efficiency of retention and an enhancement factor of 42 for a pre-concentration time of 180 seconds (sample flow rate = 3 ml min -1 ) with acetic acid elution volumes of 80 μl. The detection limit (3 s) is 7 ng l -1 and the relative standard deviation (n = 7200 ng l -1 ) is 5.8%. The analytical performance of the XAD system is: 72% efficiency of retention and an enhancement factor of 25 for a pre-concentration time of 180 s (sample flow rate = 3 ml min -1 ) with nitric acid elution volumes of 300 μl. The detection limit is 66 ng l -1 and the relative standard deviation (n = 7200 ng l -1 ) is 8.3%. Applications to the determination of tellurium in tap water and the validation of the analytical methodology employing SRM 1643e as certified reference material are shown

Production and characterization Te-peptide by induced autolysis of Saccharomyces cerevisiae.

Science.gov (United States)

Morya, V K; Dong, Shin Jae; Kim, Eun-ki

2014-04-01

Recently, the interest in mimicking functions of chalcogen-based catalytic antioxidants like selenoenzymes, has been increased. Various attempts had been done with selenium, but very few attempts were carried out with tellurium. Bio-complex formation and characterization of tellurium was not tried earlier by using any organism. The present study was focused on tellurium peptide production, characterization, and bioactivity assessment especially Mimetic to glutathione peroxidase (GPx). The production was achieved by the autolysis of total proteins obtained from Saccharomyces cerevisiae ATCC 7752 grown with inorganic tellurium. The GPx-like activity of the hydrolyzed tellurium peptide was increased when prepared by autolysis, but decreased when prepared by acid hydrolysis. Tellurium peptide produced by autolysis of the yeast cell showed increased GPx-like activity as well as tellurium content. Tellurium peptide showed little toxicity, compared to highly toxic inorganic tellurium. The results showed the potential of tellurium peptide as an antioxidant that can be produced by simple autolysis of yeast cells.

Challenges in assessment of clean energy supply-chains based on byproduct minerals: A case study of tellurium use in thin film photovoltaics

International Nuclear Information System (INIS)

Bustamante, Michele L.; Gaustad, Gabrielle

2014-01-01

Highlights: • Byproduct mining presents unique challenges to quantifying energy security issues. • This case study shows Te scarcity is closely tied to Cu demand and production. • Material intensity changes over time have a significant impact on projections. • Recycling as a mitigation strategy is shown to have poor short-term results. - Abstract: Transitioning to a sustainable energy supply will be critical to meeting future economic and environmental goals. This transition will require optimizing and commercializing a portfolio of new clean energy technologies. However, many promising clean energy technologies are based on materials with inherent risks in their supply; these risks include scarcity, price volatility, criticality, and other potential supply-chain disruptions. Using tellurium use in CdTe photovoltaics as a case study, this paper presents analysis of some of the key challenges associated with modeling byproduct systems (a supply-chain where a key material is actually a byproduct of extraction of another material, copper in the case of tellurium). This work presents a novel modeling approach; the results of the case study are used to identify potential supply risks facing this clean technology, with a unique focus on sensitivity to changes in the preliminary lifecycle stages. Supply-chain sensitivities are connected with direct environmental impacts to frame the implications in a broader sustainability context and to emphasize the future role of recycling. Ultimately, it was shown that if historical supply and demand trends continue, supply gap conditions will emerge before the end of the current decade. However, improvements in byproduct yield, end-use recycling rate, and end-use material intensity exhibit significant leverage to minimize risk in the energy-critical tellurium supply-chain

Gamma Radiation Dosimetry Using Tellurium Dioxide Thin Film Structures

Directory of Open Access Journals (Sweden)

Olga Korostynska

2002-08-01

Full Text Available Thin films of Tellurium dioxide (TeO2 were investigated for γ-radiation dosimetry purposes. Samples were fabricated using thin film vapour deposition technique. Thin films of TeO2 were exposed to a 60Co γ-radiation source at a dose rate of 6 Gy/min at room temperature. Absorption spectra for TeO2 films were recorded and the values of the optical band gap and energies of the localized states for as-deposited and γ-irradiated samples were calculated. It was found that the optical band gap values were decreased as the radiation dose was increased. Samples with electrical contacts having a planar structure showed a linear increase in current values with the increase in radiation dose up to a certain dose level. The observed changes in both the optical and the electrical properties suggest that TeO2 thin film may be considered as an effective material for room temperature real time γ-radiation dosimetry.

Flavoprotein-mediated tellurite reduction: structural basis and applications to the synthesis of tellurium-containing nanostructures

Directory of Open Access Journals (Sweden)

Mauricio Arenas-Salinas

2016-07-01

Full Text Available The tellurium oxyanion tellurite (TeO32- is extremely harmful for most organisms. It has been suggested that a potential bacterial tellurite resistance mechanism would consist of an enzymatic, NAD(PH-dependent, reduction to the less toxic form elemental tellurium (Te0. To date, a number of enzymes such as catalase, type II NADH dehydrogenase and terminal oxidases from the electron transport chain, nitrate reductases, and dihydrolipoamide dehydrogenase (E3, among others, have been shown to display tellurite-reducing activity. This activity is generically referred to as tellurite reductase (TR. Bioinformatic data resting on some of the abovementioned enzymes enabled the identification of common structures involved in tellurite reduction including vicinal catalytic cysteine residues and the FAD/NAD(P+-binding domain, which is characteristic of some flavoproteins. Along this line, thioredoxin reductase (TrxB, alkyl hydroperoxide reductase (AhpF, glutathione reductase (GorA, mercuric reductase (MerA, NADH: flavorubredoxin reductase (NorW, dihydrolipoamide dehydrogenase, and the putative oxidoreductase YkgC from Escherichia coli or environmental bacteria were purified and assessed for TR activity. All of them displayed in vitro TR activity at the expense of NADH or NADPH oxidation. In general, optimal reducing conditions occurred around pH 9-10 and 37 °C.Enzymes exhibiting strong TR activity produced Te-containing nanostructures (TeNS. While GorA and AhpF generated TeNS of 75 nm average diameter, E3 and YkgC produced larger structures (> 100 nm. Electron-dense structures were observed in cells over-expressing genes encoding TrxB, GorA and YkgC.

Tracing Tellurium and Its Nanostructures in Biology.

Science.gov (United States)

Zare, Bijan; Nami, Mohammad; Shahverdi, Ahmad-Reza

2017-12-01

Tellurium (Te) is a semimetal rare element in nature. Together with oxygen, sulfur (S), and selenium (Se), Te is considered a member of chalcogen group. Over recent decades, Te applications continued to emerge in different fields including metallurgy, glass industry, electronics, and applied chemical industries. Along these lines, Te has recently attracted research attention in various fields. Though Te exists in biologic organisms such as microbes, yeast, and human body, its importance and role and some of its potential implications have long been ignored. Some promising applications of Te using its inorganic and organic derivatives including novel Te nanostructures are being introduced. Before discovery and straightforward availability of antibiotics, Te had considered and had been used as an antibacterial element. Antilishmaniasis, antiinflammatory, antiatherosclerotic, and immuno-modulating properties of Te have been described for many years, while the innovative applications of Te have started to emerge along with nanotechnological advances over the recent years. Te quantum dots (QDs) and related nanostructures have proposed novel applications in the biological detection systems such as biosensors. In addition, Te nanostructures are used in labeling, imaging, and targeted drug delivery systems and are tested for antibacterial or antifungal properties. In addition, Te nanoparticles show novel lipid-lowering, antioxidant, and free radical scavenging properties. This review presents an overview on the novel forms of Te, their potential applications, as well as related toxicity profiles.

Influence of the hydrolysis conditions on the properties of tellurium coatings obtained from hydrochloric acid baths

International Nuclear Information System (INIS)

Bigelis, V.M.; Kim, G.N.; Navalikhin, L.V.; Kalanov, M.; Abrarov, O.A.

1982-01-01

The structure of tellurium coatings has been studied using the methods of activational analysis on fast neutrons, roentgenography using DRON-2. The study is carried out in electrolyte 1N TeO 2 +6NHCl+2NH 2 SO 4 at the temperatures 25 and 95 deg C in the range of current densities 10-150 mA/cm 2 with and without mixing. Atomic content of chlorine and oxygen in deposite depending on the electrolyte work is determined. Nicrohardness, density, specific resistance of the coatings investigated are determined

Near threshold electron impact ionization cross section for tellurium atoms

International Nuclear Information System (INIS)

Chipev, F.F.; Chernyshova, I.V.; Kontros, J.E.; Shpenik, O.B.

2004-01-01

Full text: Up today electron-impact ionization is one of the most intensively investigated processes in atomic and molecular physics [1]. These experiments however, are associated with difficulties: high temperatures and densities are required to produce atomic beams and monochromatic intensive electron beams. A crossed electron and atomic beams scattering geometry was employed to measure the ionization efficiency curve for tellurium atoms. Our electron spectrometer comprises two serially mounted hypocycloidal electron energy analyzers [2], the first being the monochromator and the second - the scattered electron analyzer. The whole spectrometer is immersed into the homogenous magnetic field. Great care was taken in selecting the value of the extracting potential at the electrode, mounted normally to the atomic beam direction. By careful choosing this potential as low as possible (∼1.4 V), its influence on the motion of the monochromatized electrons in the collision region was minimized and the full collection of the formed ions was reached. The atom beam was produced using a compact effusion source made of the stainless steel with a microchannel exit to minimise the angular divergency of the beam. The temperature of the microchannel plate was taken about 50 K higher than that of the metal vapour in the heated reservoir. This atomic beam source enabled to produce an atomic beam with the concentration of two orders of magnitude higher than that in the case of a standard effusion source. A typical value of the electron energy spread was 0.15 eV (FWHM) in the 0.1-15 eV energy range. The primary electron beam current was equal to 10 -7 A. Such values of electron energy spread and beam current for the primary electron beam passing through the collision chamber were chosen to provide identical conditions for carrying out all the measurements. The energy scale was calibrated with the accuracy of ± 0.05 eV. The measured ionization cross-section normalized to the results

Reprint of “Extracellular production of tellurium nanoparticles by the photosynthetic bacterium Rhodobacter capsulatus”

Energy Technology Data Exchange (ETDEWEB)

Borghese, Roberto, E-mail: roberto.borghese@unibo.it [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy); Brucale, Marco [Institute for the Study of Nanostructured Materials (CNR-ISMN), Rome (Italy); Fortunato, Gianuario [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy); Lanzi, Massimiliano [Dept. of Industrial Chemistry “Toso Montanari”, University of Bologna (Italy); Mezzi, Alessio [Institute for the Study of Nanostructured Materials (CNR-ISMN), Rome (Italy); Valle, Francesco; Cavallini, Massimiliano [Institute for the Study of Nanostructured Materials (CNR-ISMN), Bologna (Italy); Zannoni, Davide [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy)

2017-02-15

Highlights: • Tellurite is reduced by R. capsulatus as cytosolic tellurium nanoprecipitates TeNPs. • Lawsone allows R. capsulatus to produce extracellular TeNPs. • Extracellular TeNPs production depends on the carbon source used for cells growth. • Both lawsone concentration and the incubation time determine the TeNPs size. • Extracellular TeNPs are coated with extracellular polymeric substances (EPS). - Abstract: The toxic oxyanion tellurite (TeO{sub 3}{sup 2−}) is acquired by cells of Rhodobacter capsulatus grown anaerobically in the light, via acetate permease ActP2 and then reduced to Te{sup 0} in the cytoplasm as needle-like black precipitates. Interestingly, photosynthetic cultures of R. capsulatus can also generate Te{sup 0} nanoprecipitates (TeNPs) outside the cells upon addition of the redox mediator lawsone (2-hydroxy-1,4-naphtoquinone). TeNPs generation kinetics were monitored to define the optimal conditions to produce TeNPs as a function of various carbon sources and lawsone concentration. We report that growing cultures over a 10 days period with daily additions of 1 mM tellurite led to the accumulation in the growth medium of TeNPs with dimensions from 200 up to 600–700 nm in length as determined by atomic force microscopy (AFM). This result suggests that nucleation of TeNPs takes place over the entire cell growth period although the addition of new tellurium Te{sup 0} to pre-formed TeNPs is the main strategy used by R. capsulatus to generate TeNPs outside the cells. Finally, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR) analysis of TeNPs indicate they are coated with an organic material which keeps the particles in solution in aqueous solvents.

Total β-decay energies and masses of tin, antimony and tellurium isotopes in the vicinity of 50132Sn82

International Nuclear Information System (INIS)

Lund, E.; Aleklett, K.; Rudstam, G.

1977-01-01

Experimental β-decay energies for short-lived isotopes of tin, antimony and tellurium are presented. Mass-separated sources were produced at the on-line isotope separator OSIRIS. By applying β-γ coincidence methods, total β-decay energies have been determined for the following nuclides: 127-131 Sn, 128 130 131 134 Sb and 134 135 Te. The atomic mass excess has been derived for these nuclei, and comparisons are made with mass formula predictions. (Auth.)

In vitro and in vivo activity of an organic tellurium compound on Leishmania (Leishmania chagasi.

Directory of Open Access Journals (Sweden)

Isabella Aparecida Salerno Pimentel

Full Text Available Tellurium compounds have shown several biological properties and recently the leishmanicidal effect of one organotellurane was demonstrated. These findings led us to test the effect of the organotellurium compound RF07 on Leishmania (Leishmania chagasi, the agent of visceral leishmaniasis in Latin America. In vitro assays were performed in L. (L. chagasi-infected bone marrow derived macrophages treated with different concentrations of RF07. In in vivo experiments Golden hamsters were infected with L. (L. chagasi and injected intraperitoneally with RF07 whereas control animals received either Glucantime or PBS. The effect of RF07 on cathepsin B activity of L. (L. chagasi amastigotes was assayed spectrofluorometrically using fluorogenic substrates. The main findings were: 1 RF07 showed significant leishmanicidal activity against intracellular parasites at submicromolar concentrations (IC50 of 529.7±26.5 nM, and the drug displayed 10-fold less toxicity to macrophages (CC50 of 5,426±272.8 nM; 2 kinetics assays showed an increasing leishmanicidal action of RF07 at longer periods of treatment; 3 one month after intraperitoneal injection of RF07 L. (L. chagasi-infected hamsters showed a reduction of 99.6% of parasite burden when compared to controls that received PBS; 4 RF07 inhibited the cathepsin B activity of L. (L. chagasi amastigotes. The present results demonstrated that the tellurium compound RF07 is able to destroy L. (L. chagasi in vitro and in vivo at concentrations that are non toxic to the host. We believe these findings support further study of the potential of RF07 as a possible alternative for the chemotherapy of visceral leishmaniasis.

Ab-initio study of pure sup 7 sup 7 Se and sup 1 sup 2 sup 5 Te systems and of the sup 7 sup 7 Se nuclear quadrupole interaction in tellurium

CERN Document Server

Oh, Y K; Cho, H S

1999-01-01

Using the Hartree-Fock cluster procedure, we have studied the electric-field gradient tensors at the nuclear sites of sup 7 sup 7 Se and sup 1 sup 2 sup 5 Te in pure sup 1 sup 2 sup 5 Te systems and in tellurium crystalline system's with a sup 7 sup 7 Se impurity. From the results for the pure systems, sup 7 sup 7 Se in selenium and sup 1 sup 2 sup 5 Te in tellurium, using the observed quadrupole moments: Q( sup 7 sup 7 Se) 0.75 +- 0.07 barns and Q( sup 1 sup 2 sup 5 Te) = 0.35 +- 0.04 barns. Comparison is made with earlier values obtained by different methods. Using our calculated values of Q and the results of a study of the field-gradient tensors for sup 7 sup 7 Se in tellurium, the theoretical values of the quadrupole coupling constants are found to agree, within about 7 percent, with experiment. The calculated asymmetry parameters are also found to be in reasonable agreement with the experiment values, although the agreement not as close as in the case of the quadrupole -coupling constants. Directions fo...

Melt-gas phase equilibria and state diagrams of the selenium-tellurium system

Science.gov (United States)

Volodin, V. N.; Trebukhov, S. A.; Burabaeva, N. M.; Nitsenko, A. V.

2017-05-01

The partial pressures of saturated vapor of the components in the Se-Te system are determined and presented in the form of temperature-concentration dependences from which the boundaries of the melt-gas phase transition are calculated at atmospheric pressure and vacuums of 2000 and 100 Pa. The existence of azeotropic mixtures is revealed. It is found that the points of inseparably boiling melts correspond to 7.5 at % of Se and 995°C at 101325 Pa, 10.9 at % at 673°C and 19.5 at % at 522°C in vacuums of 2000 and 100 Pa, respectively. A complete state diagram is constructed, including the fields of gas-liquid equilibria at atmospheric and low pressures, the boundaries of which allow us to assess the behavior of selenium and tellurium upon distillation fractionation.

Simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples using hydride generation ICPMS

International Nuclear Information System (INIS)

Jankowski, L.M.; Breidenbach, R.; Bakker, I.J.I.; Epema, O.J.

2009-01-01

Full text: A quantitative method for simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples is being developed using hydride generation ICPMS. These elements must be first transformed into hydride-forming oxidation states. This is particularly challenging for selenium and antimony because selenium is susceptible to reduction to the non-hydride-forming elemental state and antimony requires strong reducing conditions. The effectiveness of three reducing agents (KI, thiourea, cysteine) is studied. A comparison is made between addition of reducing agent to the sample and addition of KI to the NaBH 4 solution. Best results were obtained with the latter approach. (author)

Luminescent Tellurium-Doped Cadmium Sulfide Electrodes as Probes of Semiconductor Excited-State Deactivation Processes in Photoelectrochemical Cells.

Science.gov (United States)

1980-08-12

photocurrent and emission intensity. Whereas CdS:Te electrochemistry consisted of oxidation of an electrolyte 2+ reductant, ZnO underwent photoanodic...employed n- and 1 3 2,3 3 3,4p-type GaPl’ n-type ZnO , n-type CdS , and n- and p-type GaAs. We have focussed our attention recently on n-type, tellurium...should point out that our treatment of Or and 0x is not without precedent. Both GaP- and ZnO -based PECs have been examined in this regard.l12 The

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Lindemann, T.; Prange, A.; Neidhart, B. [GKSS Research Centre, Geesthacht (Germany). Inst. of Physical and Chemical Analysis; Dannecker, W. [Hamburg Univ. (Germany). Inst. fuer Anorganische und Angewandte Chemie

2000-10-01

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 C whereas at -20 C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%. (orig.)

Separation process of 99Mo from 132Te using thiourea as a complex agent. Application to the separation of 99Mo from fission products

International Nuclear Information System (INIS)

Mestnik, S.A.C.; Silva, C.P.G. da

1986-01-01

A radiochemical method has been developed to separate 99 Mo from 13 2Te both produced in the fission of 235 U. The method is based on the formation of a cationic complex of tellurium with thiourea in acid medium which is retained on the cationic exchange resin (Dowex 50W-X8, 100-200 mesh) while the molyhdenum does not form such complex and passes through. The experimental results show that the retention of Te-thiourea complex on the resin is (98,3 +- 1,1) %. (Author) [pt

Calculations of energy levels and electromagnetic properties for tellurium pair isotopes, by unified method

International Nuclear Information System (INIS)

Teixeira, R.R.P.

1988-01-01

Calculations with the Unified Model (vibrator coupled to two particles), of the energy levels and the eletromagnetic properties have been performed and compared with the twelve pair isotopes from tellurium with A between 112 and 134. The results were analysed using as particles interaction: pairing and SDI (Surface Delta Interaction). The SDI and 3 fonons collective states were used in the fittings, and a syntematic comparison between the theoretical and experimental results was made. The dependence of the results with the model parameters was determined, through large variation sof them. Calculations using 4 fonons have been made, and the importance of the introduced variations in the results was discussed. Calculations have been made in the VAX Computer of the Pelletron at IFUSP. (author) [pt

Development of tellurium oxide and lead-bismuth oxide glasses for mid-wave infra-red transmission optics

Science.gov (United States)

Zhou, Beiming; Rapp, Charles F.; Driver, John K.; Myers, Michael J.; Myers, John D.; Goldstein, Jonathan; Utano, Rich; Gupta, Shantanu

2013-03-01

Heavy metal oxide glasses exhibiting high transmission in the Mid-Wave Infra-Red (MWIR) spectrum are often difficult to manufacture in large sizes with optimized physical and optical properties. In this work, we researched and developed improved tellurium-zinc-barium and lead-bismuth-gallium heavy metal oxide glasses for use in the manufacture of fiber optics, optical components and laser gain materials. Two glass families were investigated, one based upon tellurium and another based on lead-bismuth. Glass compositions were optimized for stability and high transmission in the MWIR. Targeted glass specifications included low hydroxyl concentration, extended MWIR transmission window, and high resistance against devitrification upon heating. Work included the processing of high purity raw materials, melting under controlled dry Redox balanced atmosphere, finning, casting and annealing. Batch melts as large as 4 kilograms were sprue cast into aluminum and stainless steel molds or temperature controlled bronze tube with mechanical bait. Small (100g) test melts were typically processed in-situ in a 5%Au°/95%Pt° crucible. Our group manufactured and evaluated over 100 different experimental heavy metal glass compositions during a two year period. A wide range of glass melting, fining, casting techniques and experimental protocols were employed. MWIR glass applications include remote sensing, directional infrared counter measures, detection of explosives and chemical warfare agents, laser detection tracking and ranging, range gated imaging and spectroscopy. Enhanced long range mid-infrared sensor performance is optimized when operating in the atmospheric windows from ~ 2.0 to 2.4μm, ~ 3.5 to 4.3μm and ~ 4.5 to 5.0μm.

Reaction of 1-bromo-3-chloropropane with tellurium and dimethyl telluride in the system of hydrazine hydrate-alkali

International Nuclear Information System (INIS)

Russavskaya, N.V.; Levanova, E.P.; Sukhomazova, Eh.N.; Grabel'nykh, V.A.; Elaev, A.V.; Klyba, L.V.; Zhanchipova, E.R.; Albanov, A.I.; Korotaeva, I.M.; Toryashinova, D.S.D.; Korchevin, N.A.

2006-01-01

A synthesis of oligomeric substance of thiocol type, the poly(trimethyleneditelluride), from 1-bromo-3-chloropropane and elemental tellurium is performed using a hydrazine hydrate-alkali system. Reductive splitting of the tellurocol followed by alkylation with methyl iodide give rise to preparation of bis(methyltelluro)propane, which was synthesized also from dimethyl telluride and 1,3-dihalopropanes using the N 2 H 4 ·H 2 O/KOH system. The reaction products were characterized by elementary analysis, NMR, and IR spectra. Mass spectra of the synthesized low molecular weight organotellurium compounds are considered [ru

Agglomeration during wet milling of LAST (lead-antimony-silver-tellurium) powders

International Nuclear Information System (INIS)

Hall, B.D.; Case, E.D.; Ren, F.; Johnson, J.R.; Timm, E.J.

2009-01-01

LAST (lead-antimony-silver-tellurium) compounds comprise a family of semiconducting materials with good thermoelectric properties. However, the as-cast form of LAST exhibits large grain size and hence low mechanical strength. Powder processing can produce a fine powder particle size that enhances fracture strength, however the powders tend to agglomerate if the individual powder diameters are less than a few microns across. Dry milling or wet milling (hexane additions of 0 cm 3 and 10 cm 3 ) produced hard agglomerates roughly 40 μm in diameter while wet milling with hexane additions of 25 cm 3 , 30 cm 3 or 50 cm 3 resulted in small, porous agglomerates roughly 20 μm in diameter. Thus, by adjusting the amount of milling liquid used while milling LAST powders, one can shift from hard to soft agglomerates, where the literature shows that soft agglomerates are less harmful to the final, sintered product. Also, in agreement with the results from the literature on other materials, wet milling of LAST powders produced smaller particle sizes but required longer times to reach the grindability limit

Laser resonance ionization scheme development for tellurium and germanium at the dual Ti:Sa–Dye ISOLDE RILIS

CERN Document Server

Day Goodacre, T.; Fedosseev, V.N.; Forster, L.; Marsh, B.A.; Rossel, R.E.; Rothe, S.; Veinhard, M.

2016-01-01

The resonance ionization laser ion source (RILIS) is the principal ion source of the ISOLDE radioactive beam facility based at CERN. Using the method of in-source laser resonance ionization spectroscopy, a transition to a new autoionizing state of tellurium was discovered and applied as part of a three-step, three-resonance, photo-ionization scheme. In a second study, a three-step, two-resonance, photo-ionization scheme for germanium was developed and the ionization efficiency was measured at ISOLDE. This work increases the range of ISOLDE RILIS ionized beams to 31 elements. Details of the spectroscopy studies are described and the new ionization schemes are summarized.

Laser resonance ionization scheme development for tellurium and germanium at the dual Ti:Sa–Dye ISOLDE RILIS

Energy Technology Data Exchange (ETDEWEB)

Day Goodacre, T., E-mail: thomas.day.goodacre@cern.ch [CERN, CH-1211 Geneva 23 (Switzerland); School of Physics and Astronomy, The University of Manchester, Manchester M13 9PL (United Kingdom); Fedorov, D. [Petersburg Nuclear Physics Institute, 188350 Gatchina (Russian Federation); Fedosseev, V.N.; Forster, L.; Marsh, B.A. [CERN, CH-1211 Geneva 23 (Switzerland); Rossel, R.E. [CERN, CH-1211 Geneva 23 (Switzerland); Institut für Physik, Johannes Gutenberg Universität, D-55099 Mainz (Germany); Faculty of Design, Computer Science and Media, Hochschule RheinMain, Wiesbaden (Germany); Rothe, S.; Veinhard, M. [CERN, CH-1211 Geneva 23 (Switzerland)

2016-09-11

The resonance ionization laser ion source (RILIS) is the principal ion source of the ISOLDE radioactive beam facility based at CERN. Using the method of in-source laser resonance ionization spectroscopy, a transition to a new autoionizing state of tellurium was discovered and applied as part of a three-step, three-resonance, photo-ionization scheme. In a second study, a three-step, two-resonance, photo-ionization scheme for germanium was developed and the ionization efficiency was measured at ISOLDE. This work increases the range of ISOLDE RILIS ionized beams to 31 elements. Details of the spectroscopy studies are described and the new ionization schemes are summarized.

Effect of aging and temperature on alternating current conductivity of tellurium thin films

Energy Technology Data Exchange (ETDEWEB)

Tsiulyanu, D. [Technical University, Department of Physics, bul. Dacia 41, MD-2060, Chisinau (Moldova, Republic of)], E-mail: tsiu@cni.md; Marian, T.; Tiuleanu, A. [Technical University, Department of Physics, bul. Dacia 41, MD-2060, Chisinau (Moldova, Republic of); Liess, H.-D.; Eisele, I. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany)

2009-02-27

The impedance spectra of tellurium films with interdigital platinum electrodes were investigated in air at temperatures between 10 and 50 deg. C . Cole-Cole analysis made it possible to assess time constants, resistance, and capacitance of the film at characteristic frequencies and the dependence of these parameters on aging and temperature. Aging under normal conditions over 12 months led to a relative increase of only {approx} 5% in film impedance at the characteristic frequency. However, aging noticeably influences the electrical resistance of the film at high (> 500 kHz) frequencies, and capacitance diminished after 12 months by more than 50% throughout the spectrum. Scanning electron microscopy confirmed that the effect of aging is due to structural changes in the film. Temperature does not influence the capacitance of the film but uncommonly influences its resistance, which reaches a maximum at around 20 deg. C . This is ascribed to desorption of oxygen previously adsorbed from the environment.

Effect of aging and temperature on alternating current conductivity of tellurium thin films

International Nuclear Information System (INIS)

Tsiulyanu, D.; Marian, T.; Tiuleanu, A.; Liess, H.-D.; Eisele, I.

2009-01-01

The impedance spectra of tellurium films with interdigital platinum electrodes were investigated in air at temperatures between 10 and 50 deg. C . Cole-Cole analysis made it possible to assess time constants, resistance, and capacitance of the film at characteristic frequencies and the dependence of these parameters on aging and temperature. Aging under normal conditions over 12 months led to a relative increase of only ∼ 5% in film impedance at the characteristic frequency. However, aging noticeably influences the electrical resistance of the film at high (> 500 kHz) frequencies, and capacitance diminished after 12 months by more than 50% throughout the spectrum. Scanning electron microscopy confirmed that the effect of aging is due to structural changes in the film. Temperature does not influence the capacitance of the film but uncommonly influences its resistance, which reaches a maximum at around 20 deg. C . This is ascribed to desorption of oxygen previously adsorbed from the environment

Study on concentration nonlinearity of interacting acoustic flows in cadmium sulfide and tellurium

International Nuclear Information System (INIS)

Ilisavskij, Yu.V.; Kulakova, L.A.; Yakhkind, Eh.Z.

1976-01-01

The ratio of an one-mode (self-action of an external monochromatic sound wave) and a many-mode (interaction of an external wave with crystal thermal phonons) concentration nonlinearity has been experimentally investigated on sound amplification in cadmium sulphide and tellurium. It has been shown that in a strong piezoelectric the main part in the nonlinear limitation of the sound amplification in a drift field is played by the wave interaction, i.e., the transfer of the sound wave energy into the crystal sound modes starts before the nonlinear self-action of a wave. In Te characterized by a large value of the electromechanical coupling constant value at the sound frequency of about 250 MHz the threshold of many-mode nonlinearity is achieved in fields much below the critical one, and corresponds to the sound intensity as low as 10 -7 W/cm 2 , as compared with 10 -2 W/cm 2 -the threshold of the one-mode nonlinearity

Electrochemical and antimicrobial activity of tellurium oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Gupta, Pramod K. [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Sharma, Prem Prakash; Sharma, Anshu [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Khan, Zishan H., E-mail: zishan_hk@yahoo.co.in [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Solanki, Pratima R., E-mail: pratimarsolanki@gmail.com [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India)

2016-09-15

Highlights: • TeO{sub 2} NPs synthesized without using any catalyst by chemical vapour deposition method. • The growth temperature was 410 °C with continuous flow of O{sub 2.} • TeO{sub 2} NPs have anti-bacterial activity against E. coli, K. pneumoniae and S. aureus while enhances the growth of S. pyogenes. • TeO{sub 2} shows maximum redox current at pH 7 for phosphate buffer solution. - Abstract: Thin film of tellurium oxide (TeO{sub 2}) has been synthesized by chemical vapour deposition method onto indium tin oxide (ITO) coated glass substrate without using any catalyst. XRD pattern of TeO{sub 2} thin film suggests that the structure of TeO{sub 2} changes from amorphous to crystalline (paratellurite) on dispersing into deionized water. Zeta potential measurement reveals a positive surface potential of 28.8 mV. TEM images shows spherical shaped TeO{sub 2} nanoparticles having average particle size of 65 nm. Electrochemical studies of TeO{sub 2}/ITO electrode exhibit improved electron transfer owing to its inherent electron transfer property at pH 7.0 of phosphate buffer. Antimicrobial activity of TeO{sub 2} has been studied for gram-positive (Staphylococcus aureus and Streptococcus pyogenes) and gram negative (Escherichia coli and Klebsiella pneumoniae) bacterial and fungal strains (Aspergillus nizer and Candida albicans). These studies suggest that the TeO{sub 2} NPs inhibit the growth of E. coli, K. pneumoniae and S. aureus bacteria, whereas the same particles enhance the growth of S. pyogenes bacteria.

Antiparasitic activity of 1,3-dioxolanes containing tellurium in Trichomonas vaginalis.

Science.gov (United States)

Sena-Lopes, Ângela; das Neves, Raquel Nascimento; Bezerra, Francisco Silvestre Brilhante; de Oliveira Silva, Mara Thais; Nobre, Patrick C; Perin, Gelson; Alves, Diego; Savegnago, Lucielli; Begnini, Karine Rech; Seixas, Fabiana Kommling; Collares, Tiago; Borsuk, Sibele

2017-05-01

The increased prevalence of metronidazole-resistant infections has resulted in a search for alternative drugs for the treatment of trichomoniasis. In the present study, we report the preparation and in vitro activity of three 1,3-dioxolanes that contain tellurium (PTeDOX 01, PTeDOX 02, and PTeDOX 03) against Trichomonas vaginalis. Six concentrations of these compounds were analyzed for in vitro activity against ATCC 30236 isolate of T. vaginalis. PTeDOX 01 reported a cytotoxic effect against 100% of T. vaginalis trophozoites at a final concentration of 90μM with an IC 50 of 60μM. The kinetic growth curve of trophozoites indicated that PTeDOX 01 reduced the growth by 22% at a concentration of 90μM after an exposure of 12h, and induced complete parasite death at 24h. It induced cytotoxicity of 44% at 90μM concentration but and had no effect in lower concentrations in a culture of CHO-K1 cells. These results confirmed that PTeDOX 01 is an important drug for the treatment of T. vaginalis, and should be evaluated in other infectious agents as well. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Leaching of cadmium and tellurium from cadmium telluride (CdTe) thin-film solar panels under simulated landfill conditions

Science.gov (United States)

Ramos-Ruiz, Adriana; Wilkening, Jean V.; Field, James A.; Sierra-Alvarez, Reyes

2017-01-01

A crushed non-encapsulated CdTe thin-film solar cell was subjected to two standardized batch leaching tests (i.e., Toxicity Characteristic Leaching Procedure (TCLP) and California Waste Extraction Test (WET)) and to a continuous-flow column test to assess cadmium (Cd) and tellurium (Te) dissolution under conditions simulating the acidic- and the methanogenic phases of municipal solid waste landfills. Low levels of Cd and Te were solubilized in both batch leaching tests (leaching behavior of CdTe in the columns is related to different aqueous pH and redox conditions promoted by the microbial communities in the columns, and is in agreement with thermodynamic predictions. PMID:28472709

Optical properties of tellurium-doped InxGa1-xAsySb1-y epitaxial layers studied by photoluminescence spectroscopy

International Nuclear Information System (INIS)

Diaz-Reyes, J; Cardona-Bedoya, J A; Gomez-Herrera, M L; Herrera-Perez, J L; Riech, I; Mendoza-Alvarez, J G

2003-01-01

Controlled doping of quaternary alloys of In x Ga 1-x As y Sb 1-y with tellurium is fundamental to obtain the n-type layers needed for the development of optoelectronic devices based on p-n heterojunctions. InGaAsSb epitaxial layers were grown by liquid phase epitaxy and Te doping was obtained by incorporating small Sb 3 Te 2 pellets in the growth melt. The tellurium doping levels were in the range 10 16 -10 17 cm -3 . We have used low-temperature photoluminescence (PL) spectroscopy to study the influence of the Te donor levels on the radiative transitions shown in the PL spectra. The PL measurements were done by exciting the samples with the 448 nm line of an Ar ion laser with varying excitation powers in the range from 10 to 200 mW. For the low-doped sample the PL spectrum showed a narrow exciton-related peak centred at around 610 meV with a full width at half maximum (FWHM) of about 7 meV which is evidence of the good crystalline quality of the layers. For higher Te doping, the PL spectra show the presence of band-to-band and donor-to-acceptor transitions which overlap as the Te concentration increases. The peak of the PL band shifts to higher energies as Te doping increases due to a band-filling effect as the Fermi level enters into the conduction band. From the peak energy of the PL spectra, and using a model that includes the band-filling and band-shrinkage effects due to the carriers, we have estimated the effective carrier concentration due to doping with Te in the epilayers

From Selenium- to Tellurium-Based Glass Optical Fibers for Infrared Spectroscopies

Directory of Open Access Journals (Sweden)

Jacques Lucas

2013-05-01

Full Text Available Chalcogenide glasses are based on sulfur, selenium and tellurium elements, and have been studied for several decades regarding different applications. Among them, selenide glasses exhibit excellent infrared transmission in the 1 to 15 µm region. Due to their good thermo-mechanical properties, these glasses could be easily shaped into optical devices such as lenses and optical fibers. During the past decade of research, selenide glass fibers have been proved to be suitable for infrared sensing in an original spectroscopic method named Fiber Evanescent Wave Spectroscopy (FEWS. FEWS has provided very nice and promising results, for example for medical diagnosis. Then, some sophisticated fibers, also based on selenide glasses, were developed: rare-earth doped fibers and microstructured fibers. In parallel, the study of telluride glasses, which can have transmission up to 28 µm due to its atom heaviness, has been intensified thanks to the DARWIN mission led by the European Space Agency (ESA. The development of telluride glass fiber enables a successful observation of CO2 absorption band located around 15 µm. In this paper we review recent results obtained in the Glass and Ceramics Laboratory at Rennes on the development of selenide to telluride glass optical fibers, and their use for spectroscopy from the mid to the far infrared ranges.

Structural Modeling of Djenkolic Acid with Sulfur Replaced by Selenium and Tellurium

Directory of Open Access Journals (Sweden)

Petr Melnikov

2014-04-01

Full Text Available The comparative structural modeling of djenkolic acid and its derivatives containing selenium and tellurium in chalcogen sites (Ch = Se, Te has provided detailed information about the bond lengths and bond angles, filling the gap in what we know about the structural characteristics of these aminoacids. The investigation using the molecular mechanics technique with good approximation confirmed the available information on X-ray refinements for the related compounds methionine and selenomethionine, as well as for an estimate made earlier for telluromethionine. It was shown that the Ch-C(3 and Ch-C(4 bond lengths grow in parallel with the increasing anionic radii. Although the distances C-C, C-O, and C-N are very similar, the geometry of conformers is quite different owing to the possibility of rotation about four carbon atoms, hence the remarkable variability observed in dihedral angles. It was shown that the compounds contain a rigid block with two Ch atoms connected through a methylene group. The standard program Gaussian 03 with graphical interface Gaussview 4.1.2 has proved to be satisfactory tool for the structural description of less-common bioactive compositions when direct X-ray results are absent.

Direct determination of tellurium and its redox speciation at the low nanogram level in natural waters by catalytic cathodic stripping voltammetry.

Science.gov (United States)

Biver, Marc; Quentel, François; Filella, Montserrat

2015-11-01

Tellurium is one of the elements recently identified as technologically critical and is becoming a new emergent contaminant. No reliable method exists for its determination in environmental samples such as natural waters. This gap is filled by the method described here; it allows the rapid detection of trace concentrations of Te(IV) and Te(VI) in surface waters by differential pulse cathodic stripping voltammetry. It is based on the proton reduction catalysed by the absorption of Te(IV) on the mercury electrode. Under our conditions (0.1 mol L(-1) HCl) a detection limit of about 5 ng L(-1) for a deposition time of 300 s is achieved. Organic matter does not represent a problem at low concentrations; higher concentrations are eliminated by adsorptive purification. Tellurium occurs primarily as Te(IV) and Te(VI) in natural waters. Thus, determining total Te requires the reduction of Te(VI) that it is not electroactive. A number of reduction procedures have been carefully evaluated and a method based on the addition of TiCl3 to the acidified samples has been proven to reduce Te(VI) at the trace level to Te(IV) reliably and quantitatively. Therefore, the procedure described allows the direct determination of total Te and its redox speciation. It is flexible, reliable and cost effective compared to any possible alternative method based on the common preconcentration-ICPMS approach. It is readily implementable as a routine method and can be deployed in the field with relative ease. Copyright © 2015 Elsevier B.V. All rights reserved.

Tellurium Stable Isotopes as a Paleoredox Proxy

Science.gov (United States)

Wasserman, N.; Johnson, T. M.

2017-12-01

Despite arguments for variably-oxygenated shallow waters and anoxic deep marine waters, which delayed animal development until the Neoproterozoic Oxidation Event, the magnitude of atmospheric oxygen during the Proterozoic is still uncertain [1]. The evidence for low pO2 (<0.1-1% PAL) is based on geochemical and isotopic proxies, which track the mobilization of Fe and Mn on the continents. For example, large chromium isotope shifts occur at the Neoproterozoic Oxidation Event due to the initiation of Cr redox cycling, but this proxy is insensitive to fluctuations in the lower-pO2 conditions at other times during the Proterozoic. Tellurium, a metalloid with a lower threshold to oxidation, may be sensitive to pO2 shifts in a lower range. In the reduced forms, Te(-II) and Te(0), the element is insoluble and immobile. However, in the more oxidized phases, Te(IV) and Te(VI), Te can form soluble oxyanions (though it tends to adsorb to Fe-oxyhydroxides and clays) [2]. Te stable isotopes have been shown to fractionate during abiotic or biologic reduction of Te(VI) or Te(IV) to elemental Te(0) [3, 4]. Utilizing hydride generation MC-ICP-MS, we are able to obtain high precision (2σ 0.04‰) measurements of δ128Te/125Te for natural samples containing < 10 ng of Te. A suite of Phanerozoic and Proterozoic ironstones show significant variation in δ128Te/125Te (<0.5‰), suggesting that the Te redox cycle was active during the Proterozoic. Future directions will include Te isotope measurements of Precambrian paleosols to determine natural isotope variation before the Great Oxidation Event and experiments to determine fractionation during adsorption to Fe-oxyhydroxides. [1] Planavsky et al. (2014) Science 346 (6209), pp. 635-638 [2] Qin et al. (2017) Environmental Science and Technology 51 (11), pp 6027-6035 [3] Baesman et al. (2007) Applied Environmental Microbiology 73 (7), pp 2135-2143 [4] Smithers and Krause (1968) Canadian Journal of Chemistry 46(4): pp 583-591

Determination of tellurium in gallium by alternating current stripping voltammetry with a mercury/graphite electrode

International Nuclear Information System (INIS)

Berengard, I.B.; Kaplan, B. Ya.

1986-01-01

The analytical signal in ac stripping coltammetry (ACSV) with mercury indicator electrodes depends on the weight of the electrolytically collected analyte at the electrode surface, the depth of the collection layer being equal to the effective diffusion-layer thickness. Replacement of the static mercury drop electrode (SMDE) by the mercury/graphite electrode (MGE) is of practical interest in that the analyte detection limit can be lowered by decreasing the colume of the telluriumcontaining polarographed solution; in addition, plant laboratories find it difficult to control the SDME uniformity. The work in this article was done on a PU-1 universal polarograph in a square-wave vol tage component mode using the three-electrode cell shown. The rotating mercury/graphite electrode is found by the authors to be superior to the static mercury drop electrode in that it can lower the detection limit for tellurium in gallium to 5.10 /SUP -7percent/ , due to the smaller volume of the polarographed solution

Chemical processes for the extreme enrichment of tellurium into marine ferromanganese oxides

Science.gov (United States)

Kashiwabara, Teruhiko; Oishi, Yasuko; Sakaguchi, Aya; Sugiyama, Toshiki; Usui, Akira; Takahashi, Yoshio

2014-04-01

Tellurium, an element of growing economic importance, is extremely enriched in marine ferromanganese oxides. We investigated the mechanism of this enrichment using a combination of spectroscopic analysis and adsorption/coprecipitation experiments. X-ray Absorption Near-Edge Structure (XANES) analysis showed that in adsorption/coprecipitation systems, Te(IV) was oxidized on δ-MnO2 and not oxidized on ferrihydrite. Extended X-ray Absorption Fine Structure (EXAFS) analysis showed that both Te(IV) and Te(VI) were adsorbed on the surface of δ-MnO2 and ferrihydrite via formation of inner-sphere complexes. In addition, Te(VI) can be structurally incorporated into the linkage of Fe octahedra through a coprecipitation process because of its molecular geometry that is similar to the Fe octahedron. The largest distribution coefficient obtained in the adsorption/coprecipitation experiments was for the Te(VI)/ferrihydrite coprecipitation system, and it was comparable to those calculated from the distribution between natural ferromanganese oxides and seawater. Our XAFS and micro-focused X-ray fluorescence (μ-XRF) mapping of natural ferromanganese oxides showed that Te was structurally incorporated as Te(VI) in Fe (oxyhydr)oxide phases. We conclude that the main process for the enrichment of Te in ferromanganese oxides is structural incorporation of Te(VI) into Fe (oxyhydr)oxide phases through coprecipitation. This mechanism can explain the unique degree of enrichment of Te compared with other oxyanions, which are mainly enriched via adsorption on the surface of the solid structures. In particular, the great contrast in the distributions of Te and Se is caused by their oxidized species: (i) the similar geometry of the Te(VI) molecule to Fe octahedron, and (ii) quite soluble nature of Se(VI). Coexisting Mn oxide phases may promote structural incorporation of Te(VI) by oxidation of Te(IV), although the surface oxidation itself may not work as the critical enrichment process as

Dibromidochlorido{2-[(dimethylaminomethyl]phenyl-κ2N,C1}tellurium(IV

Directory of Open Access Journals (Sweden)

Prakul Rakesh

2012-01-01

Full Text Available The title compound, C9H13Br2ClNTe, was synthesized by reacting [2-(dimethylaminomethylphenyl]tellurium(II chloride with Br2. As a consequence, the Cl and Br atoms are not well ordered but distributed over the three possible positions such that the overall stiochiometry is two Br atoms and one Cl atom. The scrambling of the Br and Cl atoms indicates a small energy barrier for the exchange process between the apical and equatorial positions. Overall, the Te atom geometry is slightly distorted square pyramidal (τ = 0.052 for the major component. However, there is a weak secondary interaction between the Te atoms and the disordered Br/Cl atoms of a nearby molecule. The Te—Br and Te—Cl distances in both disorder components fall into two groups; a longer distance for the Br/Cl involved in this secondary interaction [2.6945 (17 Å for Br and 2.601 (9Å for Cl] and shorter bond distances to the remaining halogen atoms, indicating that this interaction has slightly weakened the Te—X bond, as is the case in the previously reported tribromido structure [Singh et al. (1990. J. Chem. Soc. Dalton Trans. pp. 907–913]. Otherwise, the metrical parameters in the two structures are not significantly different. An intermolecular C—H...Br interaction occurs.

Synthesis and reactivity of 10-alkylphenotellurazines

International Nuclear Information System (INIS)

Sadekov, I.D.; Abakarov, G.M.; Panov, V.B.; Ukhin, L.Yu.; Garnovskii, A.D.; Minkin, V.I.

1985-01-01

The reaction of N-alkyl-2,2'-dilithium diphenylamines with tellurium diiodide yields derivatives of a new heterocyclic system, phenotellurazine. 10-Alkyl-phenotellurazines readily form derivatives containing tetra- and tricoordinated tellurium, form complexes with metal salts and rhodium(I) carbonyl chloride and by bromination and nitration give 3,7-dibromo- or 3-nitro-, 3,7-dinitro, and 1,3,7,9-tetranitro derivatives

Size Controlled Synthesis of Tellurium Nanorices by Galvanic Displacement Reaction of Aluminum

International Nuclear Information System (INIS)

Wu, Tingjun; Myung, Lawrence Youngjae; Zhang, Miluo; Lee, Kyu-Hwan; Lee, Yeheun Laura; Lim, Hyo-Ryong; Kim, Bum Sung; Choa, Yong-Ho; Myung, Nosang V.

2015-01-01

ABSTRACT: Tellurium nanostructures were synthesized by galvanic displacement reaction (GDR) of aluminum in an alkaline solution containing TeO 3 2− ions. Due to negative redox potential of Al/AlO 2 − (i.e., −2.50 V vs. sat. Ag/AgCl), TeO 3 2− (+IV) can be reduced to Te 2 2− (-I) and Te 2− (-II), which resulted in the deposition of Te (0) nanostructures in the solution via chemical reaction between Te 2 2− or Te 2− and TeO 3 2− . The deposition mechanism led to the formation of unique “rice-like” nanostructures in the solution instead of branched structures on the substrate. The sharp tips of the “rice-like” nanostructures may be attributed to the high density of surface charges at the tips. The morphology, diameter and aspect ratio of Te “rice-like” nanostructures were altered by the TeO 3 2− concentration, solution pH, reaction time and the reaction temperature. Electrochemical analytical methods, including open circuit potential (OCP) and linear polarizations (LPs), were used to investigate the reaction mechanisms. The enhancement of piezoelectric constant (d 11 ) of nanorices at small diameter was probably due to a flexoelectric effect

The Present, Mid-Term, and Long-Term Supply Curves for Tellurium; and Updates in the Results from NREL's CdTe PV Module Manufacturing Cost Model (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Woodhouse, M.; Goodrich, A.; Redlinger, M.; Lokanc, M.; Eggert, R.

2013-09-01

For those PV technologies that rely upon Te, In, and Ga, first-order observations and calculations hint that there may be resource constraints that could inhibit their successful deployment at a SunShot level. These are only first-order approximations, however, and the possibility for an expansion in global Te, In, and Ga supplies needs to be considered in the event that there are upward revisions in their demand and prices.In this study, we examine the current, mid-term, and long-term prospects of Tellurium (Te) for use in PV. We find that the current global supply base of Te would support <10 GW of annual traditional CdTe PV manufacturing production. But as for the possibility that the supply base for Te might be expanded, after compiling several preliminary cumulative availability curves we find that there may be significant upside potential in the supply base for this element - principally vis a vis increasing demand and higher prices. Primarily by reducing the Tellurium intensity in manufacturing and by increasing the recovery efficiency of Te in Cu refining processes, we calculate that it may prove affordable to PV manufacturers to expand the supply base for Te such that 100 GW, or greater, of annual CdTe PV production is possible in the 2030 - 2050 timeframe.

Equilibrium evaporation behavior of polonium and its homologue tellurium in liquid lead-bismuth eutectic

International Nuclear Information System (INIS)

Ohno, Shuji; Miyahara, Shinya; Kurata, Yuji; Katsura, Ryoei; Yoshida, Shigeru

2006-01-01

Experimental study using the transpiration method investigates equilibrium evaporation behavior of radionuclide polonium ( 210 Po) generated and accumulated in liquid lead-bismuth eutectic (LBE) cooled nuclear systems. The experiment consists of two series of tests: preliminary evaporation tests for homologue element tellurium (Te) in LBE, and evaporation tests for 210 Po-accumulated LBE in which test specimens are prepared by neutron irradiation. The evaporation tests of Te in LBE provide the suggestion that Te exists in a chemical form of PbTe as well as the information for confirming the validity of technique and conditions of Po test. From the evaporation tests of 210 Po in LBE, we obtain fundamental data and empirical equations such as 210 Po vapor concentration in the gas phase, 210 Po partial vapor pressure, thermodynamic activity coefficients, and gas-liquid equilibrium partition coefficient of 210 Po in LBE in the temperature range from 450 to 750degC. Additionally, radioactivity concentration of 210 Po and 210m Bi vapor in a cover gas region of a typical LBE-cooled nuclear system is specifically estimated based on the obtained experimental results, and the importance of 210 Po evaporation behavior is quantitatively demonstrated. (author)

Iron-tellurium-selenium mixed oxide catalysts for the selective oxidation of propylene to acrolein

International Nuclear Information System (INIS)

Patel, B.M.; Price, G.L.

1990-01-01

This paper reports on iron-tellurium-selenium mixed oxide catalysts prepared by coprecipitation from aqueous solution investigated for the propylene to acrolein reaction in the temperature range 543-773 K. Infrared spectroscopy, electron dispersive X-ray analysis, X-ray diffraction, and isotopic tracer techniques have also been employed to characterize this catalytic system. Properties of the Fe-Te-Se mixed oxide catalysts have been compared with Fe-Te mixed oxides in an effort to deduce the functionality of Se. The selenium in the Fe-Te-Se-O catalyst has been found to be the hydrocarbon activating site. The activation energies for the acrolein and carbon dioxide formation are 71 and 54 kJ/mol, respectively. Reactions carried out with 18 O 2 have shown lattice oxygen to be primarily responsible for the formation of both acrolein and carbon dioxide. The initial and rate-determining step for acrolein formation is hydrogen abstraction as determined by an isotope effect associated with the C 3 D 6 reaction. No isotope effect is observed for carbon dioxide formation from C 3 D 6 suggesting that CO 2 is formed by parallel, not consecutive, oxidation of propylene

Enhanced Flexural Strength of Tellurium Nanowires/epoxy Composites with the Reinforcement Effect of Nanowires

Science.gov (United States)

Balguri, Praveen Kumar; Harris Samuel, D. G.; Aditya, D. B.; Vijaya Bhaskar, S.; Thumu, Udayabhaskararao

2018-02-01

Investigating the mechanical properties of polymer nanocomposite materials has been greatly increased in the last decade. In particular, flexural strength plays a major role in resisting bending and shear loads of a composite material. Here, one dimensional (1D) tellurium nanowires (TeNWs) reinforced epoxy composites have been prepared and the flexural properties of resulted TeNWs/epoxy nanocomposites are studied. The diameter and length of the TeNWs used to make TeNWs/epoxy nanocomposites are 21±2.5 nm and 697±87 nm, respectively. Plain and TeNWs/epoxy nanocomposites are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). Furthermore, significant enhancement in the flexural strength of TeNWs/epoxy nanocomposite is observed in comparison to plain epoxy composite, i.e. flexural strength is increased by 65% with the addition of very little amount of TeNWs content (0.05 wt.%) to epoxy polymer. Structural details of plain and TeNWs/epoxy at micrometer scale were examined by scanning electron microscopy (SEM). We believe that our results provide a new type of semiconductor nanowires based high strength epoxy polymer nanocomposites.

Nickel complexes of o-amidochalcogenophenolate(2-)/o-iminochalcogenobenzosemiquinonate(1-) pi-radical: synthesis, structures, electron spin resonance, and x-ray absorption spectroscopic evidence.

Science.gov (United States)

Hsieh, Chung-Hung; Hsu, I-Jui; Lee, Chien-Ming; Ke, Shyue-Chu; Wang, Tze-Yuan; Lee, Gene-Hsiang; Wang, Yu; Chen, Jin-Ming; Lee, Jyh-Fu; Liaw, Wen-Feng

2003-06-16

The preparation of complexes trans-[Ni(-SeC(6)H(4)-o-NH-)(2)](-) (1), cis-[Ni(-TeC(6)H(4)-o-NH-)(2)](-) (2), trans-[Ni(-SC(6)H(4)-o-NH-)(2)](-) (3), and [Ni(-SC(6)H(4)-o-S-)(2)](-) (4) by oxidative addition of 2-aminophenyl dichalcogenides to anionic [Ni(CO)(SePh)(3)](-) proves to be a successful approach in this direction. The cis arrangement of the two tellurium atoms in complex 2 is attributed to the intramolecular Te.Te contact interaction (Te.Te contact distance of 3.455 A). The UV-vis electronic spectra of complexes 1 and 2 exhibit an intense absorption at 936 and 942 nm, respectively, with extinction coefficient epsilon > 10000 L mol(-)(1) cm(-)(1). The observed small g anisotropy, the principal g values at g(1) = 2.036, g(2) = 2.062, and g(3) = 2.120 for 1 and g(1) = 2.021, g(2) = 2.119, and g(3) = 2.250 for 2, respectively, indicates the ligand radical character accompanied by the contribution of the singly occupied d orbital of Ni(III). The X-ray absorption spectra of all four complexes show L(III) peaks at approximately 854.5 and approximately 853.5 eV. This may indicate a variation of contribution of the Ni(II)-Ni(III) valence state. According to the DFT calculation, the unpaired electron of complex 1 and 2 is mainly distributed on the 3d(xz)() orbital of the nickel ion and on the 4p(z)() orbital of selenium (tellurium, 5p(z)()) as well as the 2p(z)() orbital of nitrogen of the ligand. On the basis of X-ray structural data, UV-vis absorption, electron spin resonance, magnetic properties, DFT computation, and X-ray absorption (K- and L-edge) spectroscopy, the monoanionic trans-[Ni(-SeC(6)H(4)-o-NH-)(2)](-) and cis-[Ni(-TeC(6)H(4)-o-NH-)(2)](-) complexes are appositely described as a resonance hybrid form of Ni(III)-bis(o-amidochalcogenophenolato(2-)) and Ni(II)-(o-amidochalcogenophenolato(2-))-(o-iminochalcogenobenzosemiquinonato(1-) pi-radical; i.e., complexes 1 and 2 contain delocalized oxidation levels of the nickel ion and ligands.

Raman and DSC studies of fragility in tellurium-zinc oxide glass formers

International Nuclear Information System (INIS)

Stavrou, Elissaios; Kripotou, Sotiria; Raptis, Constantine; Turrell, Sylvia; Syassen, Karl

2011-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out in four mixed (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses at high temperatures (Raman and DSC through the glass transition) and high pressures (Raman) with the aim of determining the fragility of these glass forming oxides. Four different criteria, corresponding to four parameters, were applied to assess the fragility of the glasses. From the DSC studies, we have obtained the fragility parameter m which corresponds to the slopes of Arrhenius (lnQ vs. 1/T g , were Q is the heating rate) plots, and the glass transition width ΔT g . Also, from the low-frequency Raman scattering, and in particular the boson peak intensity of the glasses at T g , we have estimated the fragility ratio r R (T g ) = I min /I max whose value serves as another (empirical) fragility criterion. Finally, from high pressure Raman measurements on the glasses, we have estimated the Grueneisen parameter γ T for each glass, which constitutes the fourth fragility parameter adopted in this work. Considering the four parameters ΔT g , m, r (T g ) and γ T and the generally accepted (empirical) fragility criteria, we conclude that the mixed tellurium-zinc oxides constitute strong-to-intermediate glass formers (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Thorium–phosphorus triamidoamine complexes containing Th–P single- and multiple-bond interactions

Science.gov (United States)

Wildman, Elizabeth P.; Balázs, Gábor; Wooles, Ashley J.; Scheer, Manfred; Liddle, Stephen T.

2016-01-01

Despite the burgeoning field of uranium-ligand multiple bonds, analogous complexes involving other actinides remain scarce. For thorium, under ambient conditions only a few multiple bonds to carbon, nitrogen, oxygen, sulfur, selenium and tellurium are reported, and no multiple bonds to phosphorus are known, reflecting a general paucity of synthetic methodologies and also problems associated with stabilising these linkages at the large thorium ion. Here we report structurally authenticated examples of a parent thorium(IV)–phosphanide (Th–PH2), a terminal thorium(IV)–phosphinidene (Th=PH), a parent dithorium(IV)–phosphinidiide (Th–P(H)-Th) and a discrete actinide–phosphido complex under ambient conditions (Th=P=Th). Although thorium is traditionally considered to have dominant 6d-orbital contributions to its bonding, contrasting to majority 5f-orbital character for uranium, computational analyses suggests that the bonding of thorium can be more nuanced, in terms of 5f- versus 6d-orbital composition and also significant involvement of the 7s-orbital and how this affects the balance of 5f- versus 6d-orbital bonding character. PMID:27682617

Test of irradiation of tellurium oxide for obtaining iodine-131 by dry distillation; Prueba de irradiacion de dioxido de telurio para obtener yodo-131 por destilacion seca

Energy Technology Data Exchange (ETDEWEB)

Alanis M, J. [ININ, Departamento de Materiales Radiactivos, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-15

With the purpose of optimizing to the maximum independently the work of the reactor of those mathematical calculations of irradiation that are already optimized, now it corresponds to carry out irradiation tests in the different positions with their respective neutron fluxes that it counts the reactor for samples irradiation. Then, it is necessary to carry out the irradiation of the tellurium dioxide through cycles, with the purpose of observing the activity that it goes accumulating in each cycle and this way to obtain an activity of the Iodine-131 obtained when finishing the last cycle. (Author)

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

International Nuclear Information System (INIS)

Wan Buyong; Hu Chenguo; Liu Hong; Xiong Yufeng; Li Feiyun; Xi Yi; He Xiaoshan

2009-01-01

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

Energy Technology Data Exchange (ETDEWEB)

Wan Buyong [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); College of Physics and Information Technology, Chongqing Normal University, Chongqing 400047 (China); Hu Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Liu Hong [State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China); Xiong Yufeng [National Center for Nanoscience and Technology, Beijing 100080 (China); Li Feiyun; Xi Yi; He Xiaoshan [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China)

2009-09-15

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

Effect of increasing tellurium content on the electronic and optical properties of cadmium selenide telluride alloys CdSe{sub 1-x}Te{sub x}: An ab initio study

Energy Technology Data Exchange (ETDEWEB)

Reshak, Ali Hussain, E-mail: maalidph@yahoo.co.uk [Institute of Physical Biology-South Bohemia University, Nove Hrady 37333 (Czech Republic); School of Material Engineering, Malaysia University of Perlis, P.O Box 77, d/a Pejabat Pos Besar, 01007 Kangar, Perlis (Malaysia); Kityk, I.V. [Electrical Engineering Department, Technical University of Czestochowa, Al. Armii Krajowej 17/19, Czestochowa (Poland); Khenata, R. [Laboratoire de Physique Quantique et de Modelisation Mathematique de la Matiere (LPQ3 M), universite de Mascara, Mascara 29000 (Algeria); Department of Physics and Astronomy, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Auluck, S. [National Physical Laboratory Dr. K S Krishnan Marg, New Delhi 110012 (India)

2011-06-16

Highlights: > Theoretical study of effect of vary Te content on band structure, density of states, linear and nonlinear optical susceptibilities of CdSe{sub 1-x}Te{sub x}. > Increasing Te content leads to a decrease in the energy band gap. > Significant enhancement of the electronic properties as a function of tellurium concentration - Abstract: An all electron full potential linearized augmented plane wave method, within a framework of GGA (EV-GGA) approach, has been used for an ab initio theoretical study of the effect of increasing tellurium content on the band structure, density of states, and the spectral features of the linear and nonlinear optical susceptibilities of the cadmium-selenide-telluride ternary alloys CdSe{sub 1-x}Te{sub x} (x = 0.0, 0.25, 0.5, 0.75 and 1.0). Our calculations show that increasing Te content leads to a decrease in the energy band gap. We find that the band gaps are 0.95 (1.76), 0.89 (1.65), 0.83 (1.56), 0.79 (1.44) and 0.76 (1.31) eV for x = 0.0, 0.25, 0.5, 0.75 and 1.0 in the cubic structure. As these alloys are known to have a wurtzite structure for x less than 0.25, the energy gaps are 0.8 (1.6) eV and 0.7 (1.55) eV for the wurtzite structure (x = 0.0, 0.25) for the GGA (EV-GGA) exchange correlation potentials. This reduction in the energy gaps enhances the functionality of the CdSe{sub 1-x}Te{sub x} alloys, at least for these concentrations, leading to an increase in the effective second-order susceptibility coefficients from 16.75 pm/V (CdSe) to 18.85 pm/V (CdSe{sub 0.75}Te{sub 0.25}), 27.23 pm/V (CdSe{sub 0.5}Te{sub 0.5}), 32.25 pm/V (CdSe{sub 0.25}Te{sub 0.75}), and 37.70 pm/V (CdTe) for the cubic structure and from 12.65 pm/V (CdSe) to 21.11 pm/V (CdSe{sub 0.75}Te{sub 0.25}) in the wurtzite structure. We find a nonlinear relationship between the absorption/emission energies and composition, and a significant enhancement of the electronic properties as a function of tellurium concentration. This variation will help in

Enhancement of Thermoelectric Properties of PEDOT:PSS and Tellurium-PEDOT:PSS Hybrid Composites by Simple Chemical Treatment

Science.gov (United States)

Jin Bae, Eun; Hun Kang, Young; Jang, Kwang-Suk; Yun Cho, Song

2016-01-01

The thermoelectric properties of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and tellurium-PEDOT:PSS (Te-PEDOT:PSS) hybrid composites were enhanced via simple chemical treatment. The performance of thermoelectric materials is determined by their electrical conductivity, thermal conductivity, and Seebeck coefficient. Significant enhancement of the electrical conductivity of PEDOT:PSS and Te-PEDOT:PSS hybrid composites from 787.99 and 11.01 to 4839.92 and 334.68 S cm-1, respectively was achieved by simple chemical treatment with H2SO4. The power factor of the developed materials could be effectively tuned over a very wide range depending on the concentration of the H2SO4 solution used in the chemical treatment. The power factors of the developed thermoelectric materials were optimized to 51.85 and 284 μW m-1 K-2, respectively, which represent an increase of four orders of magnitude relative to the corresponding parameters of the untreated thermoelectric materials. Using the Te-PEDOT:PSS hybrid composites, a flexible thermoelectric generator that could be embedded in textiles was fabricated by a printing process. This thermoelectric array generates a thermoelectric voltage of 2 mV using human body heat.

Expression of Aeromonas caviae ST pyruvate dehydrogenase complex components mediate tellurite resistance in Escherichia coli

International Nuclear Information System (INIS)

Castro, Miguel E.; Molina, Roberto C.; Diaz, Waldo A.; Pradenas, Gonzalo A.; Vasquez, Claudio C.

2009-01-01

Potassium tellurite (K 2 TeO 3 ) is harmful to most organisms and specific mechanisms explaining its toxicity are not well known to date. We previously reported that the lpdA gene product of the tellurite-resistant environmental isolate Aeromonas caviae ST is involved in the reduction of tellurite to elemental tellurium. In this work, we show that expression of A. caviae ST aceE, aceF, and lpdA genes, encoding pyruvate dehydrogenase, dihydrolipoamide transacetylase, and dihydrolipoamide dehydrogenase, respectively, results in tellurite resistance and decreased levels of tellurite-induced superoxide in Escherichia coli. In addition to oxidative damage resulting from tellurite exposure, a metabolic disorder would be simultaneously established in which the pyruvate dehydrogenase complex would represent an intracellular tellurite target. These results allow us to widen our vision regarding the molecular mechanisms involved in bacterial tellurite resistance by correlating tellurite toxicity and key enzymes of aerobic metabolism.

Comparative Analysis of Supply Risk-Mitigation Strategies for Critical Byproduct Minerals: A Case Study of Tellurium.

Science.gov (United States)

Bustamante, Michele L; Gaustad, Gabrielle; Alonso, Elisa

2018-01-02

Materials criticality assessment is a screening framework increasingly applied to identify materials of importance that face scarcity risks. Although these assessments highlight materials for the implicit purpose of informing future action, the aggregated nature of their findings make them difficult to use for guidance in developing nuanced mitigation strategy and policy response. As a first step in the selection of mitigation strategies, the present work proposes a modeling framework and accompanying set of metrics to directly compare strategies by measuring effectiveness of risk reduction as a function of the features of projected supply demand balance over time. The work focuses on byproduct materials, whose criticality is particularly important to understand because their supplies are inherently less responsive to market balancing forces, i.e., price feedbacks. Tellurium, a byproduct of copper refining, which is critical to solar photovoltaics, is chosen as a case study, and three commonly discussed byproduct-relevant strategies are selected: dematerialization of end-use product, byproduct yield improvement, and end-of-life recycling rate improvement. Results suggest that dematerialization will be nearly twice as effective at reducing supply risk as the next best option, yield improvement. Finally, due to its infrequent use at present and its dependence upon long product lifespans, recycling end-of-life products is expected to be the least effective option despite potentially offering other benefits (e.g., cost savings and environmental impact reduction).

Enrichment mechanisms of tellurium in ferromanganese crusts

Science.gov (United States)

Sakaguchi, A.; Sugiyama, T.; Usui, A.; Takahashi, Y.

2012-04-01

Marine ferromanganese crusts (FMCs) consist of iron (Fe) hydroxides and manganese (Mn) oxides with various minor and trace elements. Especially for tellurium (Te), which is recognized as one of the rare metals, it has been reported that this element is concentrated about 105 times in FMCs compared with earth's crust, and the host phase might be Fe (oxy)hydroxide (Hein et al., 2003). Actually, in our previous study, the high concentration of Te in very surface layers of FMCs was found from the top to halfway down of a seamount in the Pacific Ocean. However, the concentration of Te in surface layers through the seamount showed good correlation with that of Mn instead of Fe. In this study, we attempted to clarify the enrichment mechanism of Te in FMCs with some methods including X-ray absorption fine structure (XAFS) technique for synthesised /natural samples. Seventeen FMC samples were collected from the Takuyo-Daigo seamount, from 950 m (summit) to 3000 m in water depth, with hyper-dolphin (remotely operated vehicle) equipped with live video camera and manipulators. The growth rates of all FMC samples were estimated to be about 3 mm/Ma. Very surface layer (less than 1 mm) of all FMC was analyzed with XRD and XAFS to confirm the mineral composition and speciation of Te. Furthermore, to serve as an aid to clarify the adsorption mechanism of Te on FMCs, distribution coefficients (Kd) and oxidation states were determined through the adsorption experiments of Te(IV) and Te(VI) on ferrihydrite and δ-MnO2. In all the experiments, pH and ionic strength were adjusted to pH 7.5 and 0.7 M, respectively. The oxidation state of Te in water phase was determined with HPLC-ICP-MS. As for the analysis of oxidation and adsorption states on the solid phase, XAFS was employed. The major mineral composition of Fe and Mn had no significant variation through the water depth of Takuyo-Daigo seamount. The oxidation state of Te in all samples showed hexavalent, and there was no significant

Reaction of 1-bromo-3-chloropropane with tellurium and dimethyl telluride in the system of hydrazine hydrate-alkali; Reaktsiya 1-brom-3-khlorpropana s tellurom i dimetilditelluridom v sisteme gidrazin-gidrat-shcheloch'

Energy Technology Data Exchange (ETDEWEB)

Russavskaya, N V; Levanova, E P; Sukhomazova, Eh N; Grabel' nykh, V A; Elaev, A V; Klyba, L V; Zhanchipova, E R; Albanov, A I; Korotaeva, I M; Toryashinova, D S.D.; Korchevin, N A [SO RAN, Irkutskij Inst. Khimii imeni A.E. Favorskogo, Irkutsk (Russian Federation)

2006-05-15

A synthesis of oligomeric substance of thiocol type, the poly(trimethyleneditelluride), from 1-bromo-3-chloropropane and elemental tellurium is performed using a hydrazine hydrate-alkali system. Reductive splitting of the tellurocol followed by alkylation with methyl iodide give rise to preparation of bis(methyltelluro)propane, which was synthesized also from dimethyl telluride and 1,3-dihalopropanes using the N{sub 2}H{sub 4}{center_dot}H{sub 2}O/KOH system. The reaction products were characterized by elementary analysis, NMR, and IR spectra. Mass spectra of the synthesized low molecular weight organotellurium compounds are considered.

Acousto-optic control of internal acoustic reflection in tellurium dioxide crystal in case of strong elastic energy walkoff [Invited].

Science.gov (United States)

Voloshinov, Vitaly; Polikarpova, Nataliya; Ivanova, Polina; Khorkin, Vladimir

2018-04-01

Peculiar cases of acoustic wave propagation and reflection may be observed in strongly anisotropic acousto-optical crystals. A tellurium dioxide crystal serves as a prime example of such media, since it possesses record indexes of acoustic anisotropy. We studied one of the unusual scenarios of acoustic incidence and reflection from a free crystal-vacuum boundary in paratellurite. The directions of the acoustic waves in the (001) plane of the crystal were determined, and their basic characteristics were calculated. The carried-out acousto-optic experiment at the wavelength of light 532 nm and the acoustic frequency 73 MHz confirmed the theoretical predictions. The effects examined in the paper include the acoustic wave propagation with the record walkoff angle 74°. We also observed the incidence of the wave on the boundary at the angle exceeding 90°. Finally, we registered the close-to-back reflection of acoustic energy following the incidence. One of the stunning aspects is the distribution of energy between the incident and the back-reflected wave. The unusual features of the acoustic wave reflections pointed out in the paper are valuable for their possible applications in acousto-optic devices.

A laser system for the spectroscopy on highly charged ions, tellurium molecules, and Rydberg states of rubidium atoms; Ein Lasersystem zur Spektroskopie von hochgeladenen Ionen, Tellurmolekuelen und Rubidium-Rydberg-Zustaenden

Energy Technology Data Exchange (ETDEWEB)

Albrecht, Sebastian

2014-08-15

Optical measuring methods allow the detection and identification of the atomic structure with extraordinary precision. Deviations to theoretical predictions can indicate unknown physical effects. Therefore, precise measurements on the atomic structure continue to be of large relevance. In this work, a laser system for precision spectroscopy on Bismuth ({sup 209}Bi{sup 82+}), Tellurium ({sup 130}Te{sub 2}) and Rydberg states of Rubidium ({sup 85}Rb) has been built and characterized. Spectroscopic measurements on Tellurium and Rubidium have been achieved with this setup. The system consists of a two-stage frequency doubled diode laser, stabilized via a cavity and an RF-offsetlock to arbitrary wavelengths with absolute high stability. The setup of the laser system will be presented and the systematic error caused by the refractive index of air inside the transfer cavity will be discussed. A stability of better then 6.14 MHz at 244 nm is obtained for planned experiments on the ground state hyperfine splitting of {sup 209}Bi{sup 82+}. This will allow an increase in precision of more then four orders of magnitude for this measurement. Further increase in precision can be achieved by using an evacuated cavity. The obtained stability is measured by comparison of the laser frequency to absorption lines of Tellurium ({sup 130}Te{sub 2}). Eight reference lines, known from literature, spanning the region from 613720.717 GHz to 616803.545 GHz have been measured. The frequency measurements of three lines, coinciding with the emission spectrum of an argon-ion-laser, show deviations with respect to the published frequencies. Further inconsistencies in literature are cleared. Part of this work is also the precise measurement of 843 Doppler-free {sup 130}Te{sub 2} reference lines spanning the frequency range from 613881.150 GHz to 616614.258 GHz at a precision of better then 4 MHz for most lines. Additionally, measurements on electromagnetically induced transparency (EIT) using

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses.

Science.gov (United States)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-05-19

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO(2))(1 - x)(ZnO)(x) (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T(g) has been determined for each glass, showing a monotonous decrease of T(g) with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T(d) very close to the respective T(g) values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T(g) in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T(g) and confirms the correlation between the BP and the MRO of glasses.

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses

International Nuclear Information System (INIS)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T g has been determined for each glass, showing a monotonous decrease of T g with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T d very close to the respective T g values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T g in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T g and confirms the correlation between the BP and the MRO of glasses.

On the study of proton-irradiated Tellurium targets relevant for production of medical radioisotopes 123I and 124I

International Nuclear Information System (INIS)

Imam Kambali; Hari Suryanto; Daya Agung Sarwono; Cahyana Amiruddin

2014-01-01

The energy loss distribution and range of energetic proton beams in tellurium (Te) target have been simulated using the Stopping and Range of Ion in Matter (SRIM 2013) codes. The calculated data of the proton's range were then used to determine the optimum thickness of Te targets for future production of 123 I and 124 I from 123 Te(p,n) 123 I, 124 Te(p,n) 124 I and 124 Te(p,2n) 123 I nuclear reactions using the BATAN's Cs-30 cyclotron. It was found that for an incidence angle of 0° with respect to the target normal, the optimum thickness of 123 Te and 124 Te targets for 123 I production should be 644 µm and 1.8 mm respectively, whereas a 649 µm thick 124 Te target would be Required for 124 I production. In addition, the thickness should be decreased with increasing incidence angle. The EOB yield could theoretically reach up to 13.62 Ci of 123 I at proton energy of 22 Me V and beam current of 30 µA if the 124 Te is irradiated over a period of 3 hours. The theoretical EOB yield is comparable to the experimental data with accuracy within 10%. (author)

Tellurium sulfates from reactions in oleum and sulfur trioxide: syntheses and crystal structures of TeO(SO_4), Te_4O_3(SO_4)_5, and Te(S_2O_7)_2

International Nuclear Information System (INIS)

Logemann, Christian; Bruns, Joern; Schindler, Lisa Verena; Zimmermann, Vanessa; Wickleder, Mathias S.

2015-01-01

The reaction of K_2TeO_4 with fuming sulfuric acid (65 % SO_3) in sealed glass ampoules at 250 C led to colorless single crystals of TeO(SO_4) [triclinic, P anti 1, Z = 8, a = 819.89(3) pm, b = 836.95(4) pm, c = 1179.12(5) pm, α = 82.820(2) , β = 70.645(2) , γ = 81.897(2) , V = 753.11(6) x 10"6 pm"3]. A horseshoe type [Te_4O_3] fragment is the basic motif in the layer structure of the compound. The [Te_4O_3] moieties are linked to infinite chains by further oxide ions. Monomeric [Te_4O_3] horseshoes are found in the crystal structure of Te_4O_3(SO_4)_5 [trigonal, P3_221, Z = 3, a = 859.05(2) pm, c = 2230.66(7) pm, V = 1425.61(6) x 10"6 pm"3], which was obtained from TeO_2 and fuming sulfuric acid (65 % SO_3) at 200 C as colorless single crystals. By switching to neat SO_3 as reaction medium colorless crystals of Te(S_2O_7)_2 [P2_1/n, Z = 4, a = 1065.25(3) pm, b = 818.50(2) pm, c = 1206.27(3) pm, β = 102.097(1) , V = 1028.40(5) x 10"6 pm"3] form when ortho-telluric acid, H_6TeO_6, is used as the tellurium source. The compound was reported previously, however, obviously with a wrong crystallographic description. In the crystal structure the tellurium atoms are coordinated by two chelating disulfate ions. Further Te-O contacts link the [Te(S_2O_7)_2] units to an extended network. (Copyright copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Constitutional studies in the palladium-rhodium-tellurium (-oxygen) system. A contribution to elucidate the behaviour of Pd, Rh and Te in the vitrification process of high-level waste concentrates (HLWC)

International Nuclear Information System (INIS)

Hartmann, T.

1996-01-01

In the vitrification process of high-level waste concentrates (HLWC) from the reprocessing of nuclear spent fuel elements, about 30 different elements have to be immobilized in a solid matrix consisting of an alkali borosilicate glass. Most of the waste oxides are dissolved in the alkali borosilicate melt and become structural elements of the glasses when cooled. This, however, applies only partly to the platinum metals Ru, which forms RuO 2 , and palladium and rhodium, which deposit as sparingly soluble and electrically conducting tellurides. This might considerably impair the technical process of HLWC vitrification. Therefore, constitutional studies on the Pd-Rh-Te system became necessary. The phase diagram of the Pd-Rh-Te ternary system at temperatures of 1150, 1100, 1050, 1000, 950, 900 and 750 C was determined under inertial conditions. Oxygen exerts a major influence on the system. Already under limited availability of oxygen, the rhodium contents of the solid solution phases α 1 and α 2 are clearly diminished. Rhodium of the phases becomes oxidized selectively. The three-phase field α 1 +α 2 +L is shifted to higher palladium and tellurium contents, even oxygen is available to a limited extend only. With the oxygen in the air, the extension of the three-phase space is reduced markedly. The complex process chemistry of Pf, Rh and Te during the vitrification can be described by the state of the Pd-Rh-Te ternary system after annealing in (air) oxygen for limited periods of time. (orig./MM) [de

Leaching of cadmium and tellurium from cadmium telluride (CdTe) thin-film solar panels under simulated landfill conditions.

Science.gov (United States)

Ramos-Ruiz, Adriana; Wilkening, Jean V; Field, James A; Sierra-Alvarez, Reyes

2017-08-15

A crushed non-encapsulated CdTe thin-film solar cell was subjected to two standardized batch leaching tests (i.e., Toxicity Characteristic Leaching Procedure (TCLP) and California Waste Extraction Test (WET)) and to a continuous-flow column test to assess cadmium (Cd) and tellurium (Te) dissolution under conditions simulating the acidic- and the methanogenic phases of municipal solid waste landfills. Low levels of Cd and Te were solubilized in both batch leaching tests (<8.2% and <3.6% of added Cd and Te, respectively). On the other hand, over the course of 30days, 73% of the Cd and 21% of the Te were released to the synthetic leachate of a continuous-flow column simulating the acidic landfill phase. The dissolved Cd concentration was 3.24-fold higher than the TCLP limit (1mgL -1 ), and 650-fold higher than the maximum contaminant level established by the US-EPA for this metal in drinking water (0.005mgL -1 ). In contrast, the release of Cd and Te to the effluent of the continuous-flow column simulating the methanogenic phase of a landfill was negligible. The remarkable difference in the leaching behavior of CdTe in the columns is related to different aqueous pH and redox conditions promoted by the microbial communities in the columns, and is in agreement with thermodynamic predictions. Copyright © 2017 Elsevier B.V. All rights reserved.

Formation of tellurium nanocrystals during anaerobic growth of bacteria that use Te oxyanions as respiratory electron acceptors

Science.gov (United States)

Baesman, S.M.; Bullen, T.D.; Dewald, J.; Zhang, Dongxiao; Curran, S.; Islam, F.S.; Beveridge, T.J.; Oremland, R.S.

2007-01-01

Certain toxic elements support the metabolism of diverse prokaryotes by serving as respiratory electron acceptors for growth. Here, we demonstrate that two anaerobes previously shown to be capable of respiring oxyanions of selenium also achieve growth by reduction of either tellurate [Te(VI)] or tellurite [Te(IV)] to elemental tellurium [Te(0)]. This reduction achieves a sizeable stable-Te-isotopic fractionation (isotopic enrichment factor [??] = -0.4 to -1.0 per ml per atomic mass unit) and results in the formation of unique crystalline Te(0) nanoarchitectures as end products. The Te(0) crystals occur internally within but mainly externally from the cells, and each microorganism forms a distinctly different structure. Those formed by Bacillus selenitireducens initially are nanorods (???10-nm diameter by 200-nm length), which cluster together, forming larger (???1,000-nm) rosettes composed of numerous individual shards (???100-nm width by 1,000-nm length). In contrast, Sulfurospirillium barnesii forms extremely small, irregularly shaped nanospheres (diameter < 50 nm) that coalesce into larger composite aggregates. Energy-dispersive X-ray spectroscopy and selected area electron diffraction indicate that both biominerals are composed entirely of Te and are crystalline, while Raman spectroscopy confirms that they are in the elemental state. These Te biominerals have specific spectral signatures (UV-visible light, Raman) that also provide clues to their internal structures. The use of microorganisms to generate Te nanomaterials may be an alternative for bench-scale syntheses. Additionally, they may also generate products with unique properties unattainable by conventional physical/chemical methods. Copyright ?? 2007, American Society for Microbiology. All Rights Reserved.

Ten Good Reasons for the Use of the Tellurium-Centered Anderson-Evans Polyoxotungstate in Protein Crystallography.

Science.gov (United States)

Bijelic, Aleksandar; Rompel, Annette

2017-06-20

Protein crystallography represents at present the most productive and most widely used method to obtain structural information on target proteins and protein-ligand complexes within the atomic resolution range. The knowledge obtained in this way is essential for understanding the biology, chemistry, and biochemistry of proteins and their functions but also for the development of compounds of high pharmacological and medicinal interest. Here, we address the very central problem in protein crystallography: the unpredictability of the crystallization process. Obtaining protein crystals that diffract to high resolutions represents the essential step to perform any structural study by X-ray crystallography; however, this method still depends basically on trial and error making it a very time- and resource-consuming process. The use of additives is an established process to enable or improve the crystallization of proteins in order to obtain high quality crystals. Therefore, a more universal additive addressing a wider range of proteins is desirable as it would represent a huge advance in protein crystallography and at the same time drastically impact multiple research fields. This in turn could add an overall benefit for the entire society as it profits from the faster development of novel or improved drugs and from a deeper understanding of biological, biochemical, and pharmacological phenomena. With this aim in view, we have tested several compounds belonging to the emerging class of polyoxometalates (POMs) for their suitability as crystallization additives and revealed that the tellurium-centered Anderson-Evans polyoxotungstate [TeW 6 O 24 ] 6- (TEW) was the most suitable POM-archetype. After its first successful application as a crystallization additive, we repeatedly reported on TEW's positive effects on the crystallization behavior of proteins with a particular focus on the protein-TEW interactions. As electrostatic interactions are the main force for TEW binding

Simulation of 125I-induced DNA strand breaks in a CAP-DNA complex

International Nuclear Information System (INIS)

Li, W.; Friedland, W.; Jacob, P.

2000-01-01

DNA strand breakage induced by decay of 125 I incorporated into the pyrimidine of a small piece of DNA with a specific base pair sequence has been investigated theoretically and experimentally (Lobachevsky and Martin 2000a, 2000b; Nikjoo et al., 1996; Pomplun and Terrissol, 1994; Charlton and Humm, 1988). Recently an attempt was made to analyse the DNA kinks in a CAP-DNA complex with 125 I induced DNA strand breakage (Karamychev et al., 1999). This method could be used as a so called radioprobing for such DNa distortions like other chemical and biological assays, provided that it has been tested and confirmed in a corresponding theoretical simulation. In the measurement, the distribution of the first breaks on the DNA strands starting from their labeled end can be determined. Based on such first breakage distributions, the simulation calculation could then be used to derive information on the structure of a given DNA-protein complex. The biophysical model PARTRAC has been applied successfully in simulating DNA damage induced by irradiation (Friedland et al., 1998; 1999). In the present study PARTRAC is adapted to a DNA-protein complex in which a specific sequence of 30 base pairs of DNA is connected with the catabolite gene activator protein (CAP). This report presents the first step of the analysis in which the CAP-DNA model used in NIH is overlaid with electron track structures in liquid water and the strand breaks due to direct ionization and due to radical attack are simulated. The second step will be to take into account the neutralization of the heavily charged tellurium and the protective effect of the CAP protein against radical attack. (orig.)

Resonant ionization by laser beams: application to ions sources and to study the nuclear structure of radioactive tellurium isotopes

International Nuclear Information System (INIS)

Sifi, R.

2007-07-01

The radioactive ion beams that are produced through current isotope separators are well separated according to the A mass but not according to the Z parameter. The resonant ionization through laser beams applied to ion sources allows the production of radioactive ion beam in a very selective and efficient way by eliminating the isobaric contamination. The first chapter is dedicated to the resonant ionization by laser beams, we describe the principle, the experimental setting, the lasers used, the ionization schemes and the domain of application. The second chapter deals with the application of resonant ionization to laser ion sources for the production of radioactive ion beams. We present experimental tests performed for getting copper ion beams. Resonant ionization through laser is also used in the spectroscopy experiments performed at the Isolde (isotope separation on-line device) installation in CERN where more than 20 elements are ionized very efficiently. The technique is based on a frequency scanning around the excitation transition of the atoms in order to probe the hyperfine structure. Laser spectroscopy allows the determination of the hyperfine structure as well as the isotopic shift of atoms. In the third chapter the method is applied to the spectroscopy of tellurium atoms. First, we define the 2 parameters on which the extraction is based: charge radius and nuclear moments, then we present several theoretical models that we have used to assess our experimental results. (A.C.)

Electrical properties of tellurium clusters on the void sublattice of an opal crystal the important role played by the Te-SiO$_{2}$ interface

CERN Document Server

Berezovets, V A; Farbshtein, I I; Nizhankovskii, V I

2002-01-01

The temperature dependences of electrical resistivity and of the Hall effect of nanocluster tellurium crystals obtained by filling the voids in a dielectric (opal) matrix with a melt of pure and doped Te were studied. The Hall hole concentration p/sub eff/ was found to increase anomalously (by more than two orders of magnitude) in a sample prepared from pure Te and cooled to helium temperatures. At T = 1.45 K, the hole concentration in this sample was p/sub eff/ = equivalent to 6 * 10/sup 17/ cm/sup -3/. At the same time, the Hall effect in this sample was observed to reverse sign at T equivalent to 200 K from positive for T < 200 K to negative at higher temperatures. This implies a low impurity concentration (N/sub A/ is less than at least 10/sup 15/ cm/sup -3/). A nanocluster crystal of doped Te does not exhibit this anomaly; here, we have p/sub eff/ equivalent to 6 * 10/sup 17/ cm/sup -3/ throughout the temperature region covered, as in the original Te. These features are assigned to the formation of a ...

Aspects of the chemistry of boron

International Nuclear Information System (INIS)

Moellinger, H.

1976-01-01

Crystal phases of elementary boron are reviewed as well as boron-sulphur, boron-selenum, boron-tellurium, and boron-nitrogen compounds, carboranes, and boron-carbohydrate complexes. A boron cadastre of rivers and lakes serves to illustrate the role of boron in environmental protection. Technically relevant boron compounds and their uses are mentioned. (orig.) 891 HK/orig. 892 MB [de

Effect of composition on the degree of anisotropy of thermal expansion and electric resistance of cermet specimens of GeTe

International Nuclear Information System (INIS)

Barbakadze, K.G.; Vekua, T.S.; Ioseliani, M.I.; Kvitsiniya, K.M.

1988-01-01

A study was made on α temperature coefficient of thermal expansion and ρ specific electric resistance of cermet germanium telluride for alloys close to stoichiometric composition. It is shown that anisotropy of thermal expansion of cermet germanium telluride depends sufficiently on its composition. This dependence is clearly pronounced if tellurium content in alloys equals 50.4-51.2 at.%. The maximal anisotropy is observed in the alloy containing 50.8 at.% of tellurium. The temperature of extreme value of temperature coefficient of linear expansion decreases from 440 down to 373 deg.C for alloys with 49-50.8 at.% of tellurium, and grows from 373 up to 405 deg.C if tellurium content equals 50.8-52 at.%

The determination of some trace elements in sulphide concentrates by spectrophotometry

International Nuclear Information System (INIS)

Shelton, B.J.; Komarkova, E.; Josephson, M.; Cook, E.B.T.; Dixon, K.

1977-01-01

The report describes the determination of trace amounts (as low as 1 to 10 p.p.m. depending on the element) of arsenic, germanium, molybdenum, nickel, phosphorus, selenium, tellurium, tin, and titanium in sulphide concentrates. The proposed methods, which are detailed in the appendices, are adaptations of established procedures that were modified to allow for the complex nature of the concentrates to be analysed

Applications of precision colorimetry to elemental microanalysis

International Nuclear Information System (INIS)

Debal, E.; Peynot, S.; Poliakoff, O.; Revault, M.

1979-01-01

The sample (< 1 mg) is burnt in an oxygen flask for the determination of rhenium. It is destroyed by a wet process in a Kjeldahl flask for the determination of rhodium or tellurium (sample < 4 to 5 mg) or zirconium (sample < 1.5 mg). These elements are determined spectrophotometrically. The following reactions are used: reduction of perrhenate by tin(II) chloride in the presence of 2,2'-furildioxime or thiourea, complexation of rhodium(III) by sodium hypochlorite, formation of iodotellurite, complexation of zirconium(IV) with Xylenol Orange. (author)

Tellurium sulfates from reactions in oleum and sulfur trioxide: syntheses and crystal structures of TeO(SO{sub 4}), Te{sub 4}O{sub 3}(SO{sub 4}){sub 5}, and Te(S{sub 2}O{sub 7}){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Logemann, Christian; Bruns, Joern; Schindler, Lisa Verena; Zimmermann, Vanessa; Wickleder, Mathias S. [Carl von Ossietzky University of Oldenburg, Institute of Chemistry (Germany)

2015-04-15

The reaction of K{sub 2}TeO{sub 4} with fuming sulfuric acid (65 % SO{sub 3}) in sealed glass ampoules at 250 C led to colorless single crystals of TeO(SO{sub 4}) [triclinic, P anti 1, Z = 8, a = 819.89(3) pm, b = 836.95(4) pm, c = 1179.12(5) pm, α = 82.820(2) , β = 70.645(2) , γ = 81.897(2) , V = 753.11(6) x 10{sup 6} pm{sup 3}]. A horseshoe type [Te{sub 4}O{sub 3}] fragment is the basic motif in the layer structure of the compound. The [Te{sub 4}O{sub 3}] moieties are linked to infinite chains by further oxide ions. Monomeric [Te{sub 4}O{sub 3}] horseshoes are found in the crystal structure of Te{sub 4}O{sub 3}(SO{sub 4}){sub 5} [trigonal, P3{sub 2}21, Z = 3, a = 859.05(2) pm, c = 2230.66(7) pm, V = 1425.61(6) x 10{sup 6} pm{sup 3}], which was obtained from TeO{sub 2} and fuming sulfuric acid (65 % SO{sub 3}) at 200 C as colorless single crystals. By switching to neat SO{sub 3} as reaction medium colorless crystals of Te(S{sub 2}O{sub 7}){sub 2} [P2{sub 1}/n, Z = 4, a = 1065.25(3) pm, b = 818.50(2) pm, c = 1206.27(3) pm, β = 102.097(1) , V = 1028.40(5) x 10{sup 6} pm{sup 3}] form when ortho-telluric acid, H{sub 6}TeO{sub 6}, is used as the tellurium source. The compound was reported previously, however, obviously with a wrong crystallographic description. In the crystal structure the tellurium atoms are coordinated by two chelating disulfate ions. Further Te-O contacts link the [Te(S{sub 2}O{sub 7}){sub 2}] units to an extended network. (Copyright copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Thermodynamics of post-growth annealing of cadmium zinc telluride nuclear radiation detectors

Science.gov (United States)

Adams, Aaron Lee

Nuclear Radiation Detectors are used for detecting, tracking, and identifying radioactive materials which emit high-energy gamma and X-rays. The use of Cadmium Zinc Telluride (CdZnTe) detectors is particularly attractive because of the detector's ability to operate at room temperature and measure the energy spectra of gamma-ray sources with a high resolution, typically less than 1% at 662 keV. While CdZnTe detectors are acceptable imperfections in the crystals limit their full market potential. One of the major imperfections are Tellurium inclusions generated during the crystal growth process by the retrograde solubility of Tellurium and Tellurium-rich melt trapped at the growth interface. Tellurium inclusions trap charge carriers generated by gamma and X-ray photons and thus reduce the portion of generated charge carriers that reach the electrodes for collection and conversion into a readable signal which is representative of the ionizing radiation's energy and intensity. One approach in resolving this problem is post-growth annealing which has the potential of removing the Tellurium inclusions and associated impurities. The goal of this project is to use experimental techniques to study the thermodynamics of Tellurium inclusion migration in post-growth annealing of CdZnTe nuclear detectors with the temperature gradient zone migration (TGZM) technique. Systematic experiments will be carried out to provide adequate thermodynamic data that will inform the engineering community of the optimum annealing parameters. Additionally, multivariable correlations that involve the Tellurium diffusion coefficient, annealing parameters, and CdZnTe properties will be analyzed. The experimental approach will involve systematic annealing experiments (in Cd vapor overpressure) on different sizes of CdZnTe crystals at varying temperature gradients ranging from 0 to 60°C/mm (used to migrate the Tellurium inclusion to one side of the crystal), and at annealing temperatures ranging

Local order in molten Sesub(1-x)Tesub(x)

International Nuclear Information System (INIS)

Bellissent, R.; Tourand, G.

1980-04-01

In this paper a study of the short range order and of the coordination number in liquid Selenium-Tellurium systems is presented. The first part deals with neutron diffraction measurements of the structure factors of liquid Sesub(1-x)Tesub(x) in the whole concentration range, at 475 C, performed at EL3 reactor in Saclay using a 640 cell multidetector. From these data the radial distribution functions have been calculated. In a second part a structural model based on random chains for Selenium and on a quasicrystalline behavior of Tellurium is presented. For Se-rich melts it is assumed that Tellurium enters the Selenium chains by substitution. In the Te-rich range it is assumed that the local order is represented by substituted SeTe chains in a Tellurium matrix. This model provides with a good representation of the various structure factors. Moreover the coordination number for each concentration in the model has been calculated and the results are consistent with the experimental data. The 2 fold coordination of Se and the 3 valency of Te in the liquid state are emphasized and they can be associated with the metallisation of liquid Tellurium whereas Selenium remains a semiconductor

Contact-resonance atomic force microscopy for nanoscale elastic property measurements: Spectroscopy and imaging

International Nuclear Information System (INIS)

Stan, G.; Krylyuk, S.; Davydov, A.V.; Vaudin, M.D.; Bendersky, L.A.; Cook, R.F.

2009-01-01

Quantitative measurements of the elastic modulus of nanosize systems and nanostructured materials are provided with great accuracy and precision by contact-resonance atomic force microscopy (CR-AFM). As an example of measuring the elastic modulus of nanosize entities, we used the CR-AFM technique to measure the out-of-plane indentation modulus of tellurium nanowires. A size-dependence of the indentation modulus was observed for the investigated tellurium nanowires with diameters in the range 20-150 nm. Over this diameter range, the elastic modulus of the outer layers of the tellurium nanowires experienced significant enhancement due to a pronounced surface stiffening effect. Quantitative estimations for the elastic moduli of the outer and inner parts of tellurium nanowires of reduced diameter are made with a core-shell structure model. Besides localized elastic modulus measurements, we have also developed a unique CR-AFM imaging capability to map the elastic modulus over a micrometer-scale area. We used this CR-AFM capability to construct indentation modulus maps at the junction between two adjacent facets of a tellurium microcrystal. The clear contrast observed in the elastic moduli of the two facets indicates the different surface crystallography of these facets.

β-Telluroacroleins and β-tellurovinyl ketones: synthesis, reactions and structure

International Nuclear Information System (INIS)

Sadekov, I.D.

2002-01-01

Data on synthesis, reactivity, spectral characteristics and structure of new telluroorganic synthons, i.e. β-tellurovinylcarbonyl compounds, were generalized and systematized. Synthesis and reactions of β-telluroacroleins and similar cations were considered individually for each type of β-tellurovinylcarbonyl compounds. Special attention was paid to the use of the compounds for preparing tellurium-containing heterocycles. Reactions characteristics of carbonyl groups and tellurium-containing substituents, as well as transformation, as a result of which β-tellurovinylcarbonyl compounds and products of their reactions form tellurium-containing heterocycles, were discussed [ru

Post-Irradiation Behaviour of I131 in TeO2

International Nuclear Information System (INIS)

Jaćimović, Lj.; Stevović, J.; Veljković, S.R.

1965-01-01

The system I 131 in TeO 2 is interesting because little is known about thermal chemical changes in this target. Radioiodine was produced by neutron irradiation of TeO 2 in the reactor. Irradiated TeO 2 was dissolved in diluted NaOH. The analysis of the iodine valency forms was made by ion exchange techniques. The thermal and radiation stability of TeO 2 was studied by using the spectrophotometric method for the determination of tellurium. Post-irradiation annealing of I 131 in TeO 2 was studied in dependence on the time and temperature of the heating. The main tendency of annealing was the reduction of radioiodine. The time dependence of this process indicates a fast change at high temperatures. The curves are more complex at lower temperatures. The annealing may appear complex because of the variety of thermal reactions of iodine intermediary. It may react with products of the following processes: tellurium recoil and corresponding hot zone, beta transition of Te 131 and TeO 2 itself. The kinetics of these changes was considered and an estimation of the processes during annealing was made. The influence of the neutron flux on the kinetics of annealing was also studied. (author) [fr

New studies on mustard gold from the Dongping Mines, Hebei Province, China: The tellurian, plumbian, manganoan and mixed varieties

DEFF Research Database (Denmark)

Li, Jiuling; Makovicky, Emil

2001-01-01

geologi, Dongping gold tellurite deposit, mustard gold, calaverite, Fe-Pb-Te minerals, alteration, tellurium, filling in micro-porous, composite varieties, particles of gold......geologi, Dongping gold tellurite deposit, mustard gold, calaverite, Fe-Pb-Te minerals, alteration, tellurium, filling in micro-porous, composite varieties, particles of gold...

A simple fast microwave-assisted synthesis of thermoelectric bismuth telluride nanoparticles from homogeneous reaction-mixture

Energy Technology Data Exchange (ETDEWEB)

Pradhan, Susmita [Jadavpur University, Department of Instrumentation Science (India); Das, Rashmita [Jadavpur University, Department of Instrumentation and Electronics Engineering (India); Bhar, Radhaballabh [Jadavpur University, Department of Instrumentation Science (India); Bandyopadhyay, Rajib [Jadavpur University, Department of Instrumentation and Electronics Engineering (India); Pramanik, Panchanan, E-mail: pramanik1946@gmail.com [GLA University, Department of Chemistry and Nanoscience (India)

2017-02-15

A new simple chemical method for synthesis of nanocrystalline bismuth telluride (Bi{sub 2}Te{sub 3}) has been developed by microwave assisted reduction of homogeneous tartrate complexes of bismuth and tellurium metal ions with hydrazine. The reaction is performed at pH 10. The nano-crystallites have rhombohedral phase identified by XRD. The size distribution of nanoparticle is narrow and it ranges between 50 to 70 nm. FESEM shows that the fine powders are composed of small crystallites. The TEM micrographs show mostly deformed spherical particles and the lattice fringes are found to be 0.137 nm. Energy dispersive X-ray spectroscopy (EDX) analysis shows the atomic composition ratio between bismuth and tellurium is 2:3. Thermoelectric properties of the materials are studied after sintering by spark plasma sintering method (SPS). The grain size of the material after sintering is in the nanometer range. The material shows enhanced Seebeck coefficient and electrical conductivity value at 300 K. The figure of merit is found to be 1.18 at 300 K.

Dielectric relaxation of selenium-tellurium mixed former glasses

Science.gov (United States)

Palui, A.; Ghosh, A.

2017-05-01

We report the study of dielectric properties of mixed network former glasses of composition 0.3Ag2O-0.7(xSeO2-(1-x)TeO2); x=0, 0.1, 0.3, 0.4, 0.5 and 0.6 in a wide frequency 10 Hz - 2 MHz and temperature range 223 K - 403 K. The experimental data have been analyzed in the framework of complex dielectric permittivity. The dielectric permittivity data have been analyzed using the Cole-Cole function. The inverse temperature dependence of relaxation time obtained from real part of dielectric permittivity data follows the Arrhenius relation. The activation energy shows mixed glass former effect with variation of mixed former ratio. A non-zero value of shape parameters is observed and it is almost independent of temperature and composition.

Reactions of newly formed fission products in the gas phase

International Nuclear Information System (INIS)

Strickert, R.G.

1976-01-01

A dynamic gas-flow system was constructed which stopped fission products in the gas phase and rapidly separated (in less than 2 sec) volatile compounds from non-volatile ones. The filter assembly designed and used was shown to stop essentially all non-volatile fission products. Between 5 percent and 20 percent of tellurium fission-product isotopes reacted with several hydrocarbon gases to form volatile compounds, which passed through the filter. With carbon monoxide gas, volatile tellurium compound(s) (probably TeCO) were also formed with similar efficiencies. The upper limits for the yields of volatile compounds formed between CO and tin and antimony fission products were shown to be less than 0.3 percent, so tellurium nuclides, not their precursors, reacted with CO. It was found that CO reacted preferentially with independently produced tellurium atoms; the reaction efficiency of beta-produced atoms was only 27 +- 3 percent of that of the independently formed atoms. The selectivity, which was independent of the over-all reaction efficiency, was shown to be due to reaction of independently formed atoms in the gas phase. The gas phase reactions are believed to occur mainly at thermal energies because of the independence of the yield upon argon moderator mole-fraction (up to 80 percent). It was shown in some experiments that about one-half of the TeCO decomposed in passing through a filter and that an appreciable fraction (approximately 20 percent) of the tellurium atoms deposited on the filter reacted agin with CO. Other tellurium atoms on the filter surface (those formed by beta decay and those formed independently but not reacting in the gas phase) also reacted with CO, but probably somewhat less efficiently than atoms formed by TeCO decomposition. No evidence was found for formation of TeCO as a direct result of beta-decay

Iodine-131 production by a dry method using reactor-irradiated elementary tellurium. Part 1 - Conditions for obtaining iodine emanation and its capture. Part 2 - comparative study of preparation conditions using Pyrex, stainless steel and alumina equipment. Part 3 - production on a semi-industrial scale; Production de l'iode 131 par voie seche a partir de tellure elementaire irradie a la pile. 1ere partie - Etudes des conditions pour obtenir l'emanation de l'iode et le capter. 2eme partie - Etude comparee des conditions pour effectuer cette preparation avec des appareils en Pyrex, en acier inoxydable et en alumine. 3eme partie - production a l'echelle semi-industrielle

Energy Technology Data Exchange (ETDEWEB)

Bardy, A; Beydon, J; Murthy, T S; Doyen, J B; Lefrancois, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-04-15

A previous report has described how iodine 131 can be prepared from elementary tellurium by a dry method which consists in treating irradiated tellurium at 400 degrees in argon. The possibility of carrying out this treatment in a stainless steel or alumina apparatus has been considered. The behavior of gaseous iodine 131 towards these materials has thus been studied. If the adsorption of iodine on stainless steel is superficial desorption is rapid at 250 degrees in oxygen or 400 degrees in argon. If the adsorption is chemical in nature it becomes necessary to heat to higher temperatures. Adsorption of iodine on alumina is very weak and the iodine can be desorbed rapidly. With these materials tests have been carried out on 300 gms of tellurium containing 41 curies of iodine 131; the yields were very satisfactory ( 98 per cent). (author) [French] La methode de preparation de l iode 131 par voie seche a partir de tellure elementaire decrite dans un precedent rapport consiste a traiter le tellure irradie a 400 degres sous argon. Nous avons examine la possibilite d effectuer ce traitement dans un appareil en acier inoxidable ou en alumine. Le comportement de l iode 131 gazeux vis a vis de ces materiaux a donc ete etudie. Si l adsorption de l iode sur l acier inoxidable est superficielle la desorption est rapide a 250 degres sous oxygene ou 400 degres sous argon. Si la fixation est de nature chimique il est necessaire de chauffer a des temperatures plus elevees. L adsorption de l iode sur l alumine est res faible et l iode peut etre desorbe rapideemnt. En employant ces materiaux des essais ont ete obtenus sur 300 g de tellure contenant 41 curies d iode 131 avec un bon rendement (98 pour cent). (auteur00.

Micro-Raman spectroscopy studies of bulk and thin films of CuInTe2

International Nuclear Information System (INIS)

Ananthan, M R; Mohanty, Bhaskar Chandra; Kasiviswanathan, S

2009-01-01

Micro-Raman spectroscopy measurements were made on polycrystalline and amorphous thin films of CuInTe 2 as well as bulk polycrystalline CuInTe 2 . Various vibrational modes exhibited by the bulk and polycrystalline thin films were attributed to those expected for single crystal CuInTe 2 . Raman spectra of amorphous films presented a broad spectrum, decomposition of which revealed the presence of elemental tellurium on the film surface. Laser-induced changes on CuInTe 2 thin films were studied by acquiring spectra with higher laser beam power. Modes due to tellurium appeared when the spectra were acquired during laser–sample interaction, indicating tellurium segregation. The Raman spectra measured from polycrystalline films during high laser power irradiation did not show decrease in the intensity of the A 1 mode of CuInTe 2 in spite of loss of tellurium from the lattice. This has been interpreted as related to an increased contribution from the undistorted subsurface CuInTe 2 region at higher excitation power

Lasing transition at 1.06 μm emission in Nd3+ -doped borate-based tellurium calcium zinc niobium oxide glasses for high-power solid-state lasers.

Science.gov (United States)

Ravi, O; Prasad, K; Jain, Rajiv; Venkataswamy, M; Chaurasia, Shivanand; Deva Prasad Raju, B

2017-08-01

The spectroscopic properties of Tellurium Calcium Zinc Niobium oxide Borate (TCZNB) glasses of composition (in mol%) 10TeO 2  + 15CaO + 5ZnO + 10 Nb 2 O 5  + (60 - x)B 2 O 3  + Nd 2 O 3 (x = 0.1, 0.5, 1.0 or 1.5 mol%) have been investigated experimentally. The three phenomenological intensity parameters Ω 2 , Ω 4, Ω 6 have been calculated using the Judd-Ofelt theory and in turn radiative properties such as radiative transition probabilities, emission cross-sections, branching ratios and radiative lifetimes have been estimated. The trend found in the JO intensity parameter is Ω 2  > Ω 6  > Ω 4 If Ω 6  > Ω 4 , the glass system is favourable for the laser emission 4 F 3 /2  →  4 I 11 /2 in the infrared (IR) wavelength. The experimental values of branching ratio of 4 F 3 /2  →  4 I 11 /2 transition indicate favourable lasing action with low threshold power. The evaluated total radiative transition probabilities (A T ), stimulated emission cross-section (σ e ) and gain bandwidth parameters (σ e  × Δλ p ) were compared with earlier reports. An energy level analysis has been carried out considering the experimental energy positions of the absorption and emission bands. Copyright © 2016 John Wiley & Sons, Ltd.

Radionuclides in diffusion probing of inorganic materials based on chalcogenides

International Nuclear Information System (INIS)

Firsova, L.P.

1994-01-01

Migration of tellurium-125m, selenium-75, sulfur-35 radionuclides in solid solutions Pb 1-y (Se 0.08 Te 0.92 ) y and (Pb 1-x Sn x ) y Te 1-y , where x=0.1 and 0.2, has been studied, the results are presented. Data on dependence of selenium and tellurium self-diffusion coefficients on temperature in the range of 600-750 deg C are given. The results of the study of self-diffusion coefficient isothermal dependences on lead and tellurium vapour pressure in equilibrium with solid phases have been considered. It is ascertained that a change in the temperature and p-n transitions initiate the change in self-diffusion mechanisms of chalcogenide atoms. 8 refs., 3 tabs

Diaroyl Tellurides: Synthesis, Structure and NBO Analysis of (2-MeOC6H4CO2Te – Comparison with Its Sulfur and Selenium Isologues. The First Observation of [MgBr][R(C=TeO] Salts

Directory of Open Access Journals (Sweden)

Fumio Ando

2009-07-01

Full Text Available A series of aromatic diacyl tellurides were prepared in moderate to good yields by the reactions of sodium orpotassium arenecarbotelluroates with acyl chlorides in acetonitrile. X-ray structure analyses and theoretical calculations of 2-methoxybenzoic anhydride and bis(2-methoxybenzoyl sulfide, selenide and telluride were carried out. The two 2-MeOC6H4CO moieties of bis(2-methoxybenzoyl telluride are nearly planar and the two methoxy oxygen atoms intramolecularly coordinate to the central tellurium atom from both side of C(11-Te(11-C(22 plane. In contrast, the oxygen and sulfur isologues (2-MeOC6H4CO2E (E = O, S, show that one of the two methoxy oxygen atoms contacts with the oxygen atom of the carbonyl group connected to the same benzene ring. The structure of di(2-methoxybenzoyl selenide which was obtained by MO calculation resembles that of tellurium isologues rather than the corresponding oxygen and sulfur isologues. The reactions of di(aroyl tellurides with Grignard reagents lead to the formation of tellurocarboxylato magnesium complexes [MgBr][R(C=TeO].

Nuclear medicine. Progress report for quarter ending June 30, 1982

Energy Technology Data Exchange (ETDEWEB)

Knapp, F.F. Jr.; Ambrose, K.R.; Butler, T.A.; Goodman, M.M.; Hoeschele, J.D.; Srivastava, P.C.

1982-09-01

The oxidation products of tellurium and selenium fatty acids were shown to differ and may relate to the unique prolonged retention of tellurium fatty acids in the heart. The studies suggest that the trapping of tellurium fatty acids in the heart may result from the formation of an insoluble oxidation product after entry into the cells of the heart muscle. Also described in this report is the synthesis of several barbituric acid analogues for evaluation as potential cerebral perfusion agents. The present studies indicate that the iodovinyl-alkyl barbiturates cross the intact blood-brain barrier but undergo in vivo deiodination as measured by a high uptake of radioiodine in the thyroid. During this period four /sup 191/Os-osmate shipments were made to Medical Cooperative investigators for evaluation of the ultrashort-lived /sup 191//sup m/Ir (T/sub 1/2/ = 4.9 sec) obtained from the /sup 191//sup m/Ir generator. Seven shipments of the /sup 195//sup m/Pt-labeled cis-dichlorodiammineplatinum(II) antitumor drug were made to collaborators and fice shipments of radiolabeled tellurium fatty acids were made to the Massachusetts General Hospital.

Cs_7Sm_1_1[TeO_3]_1_2Cl_1_6 and Rb_7Nd_1_1[TeO_3]_1_2Br_1_6, the new tellurite halides of the tetragonal Rb_6LiNd_1_1[SeO_3]_1_2Cl_1_6 structure type

International Nuclear Information System (INIS)

Charkin, Dmitri O.; Black, Cameron; Downie, Lewis J.; Sklovsky, Dmitry E.; Berdonosov, Peter S.; Olenev, Andrei V.; Zhou, Wuzong; Lightfoot, Philip; Dolgikh, Valery A.

2015-01-01

Two new rare-earth – alkali – tellurium oxide halides were synthesized by a salt flux technique and characterized by single-crystal X-ray diffraction. The structures of the new compounds Cs_7Sm_1_1[TeO_3]_1_2Cl_1_6 (I) and Rb_7Nd_1_1[TeO_3]_1_2Br_1_6 (II) (both tetragonal, space group I4/mcm) correspond to the sequence of [MLn_1_1(TeO_3)_1_2] and [M_6X_1_6] layers and bear very strong similarities to those of known selenite analogs. We discuss the trends in similarities and differences in compositions and structural details between the Se and Te compounds; more members of the family are predicted. - Graphical abstract: Two new rare-earth – alkali – tellurium oxide halides were predicted and synthesized. - Highlights: • Two new rare-earth – alkali – tellurium oxide halides were synthesized. • They adopt slab structure of rare earth-tellurium-oxygen and CsCl-like slabs. • The Br-based CsCl-like slabs have been observed first in this layered family.

Maxwell rigidity and topological constraints in amorphous phase-change networks

International Nuclear Information System (INIS)

Micoulaut, M.; Otjacques, C.; Raty, J.-Y.; Bichara, C.

2011-01-01

By analyzing first-principles molecular-dynamics simulations of different telluride amorphous networks, we develop a method for the enumeration of radial and angular topological constraints, and show that the phase diagram of the most popular system Ge-Sb-Te can be split into two compositional elastic phases: a tellurium rich flexible phase and a stressed rigid phase that contains most of the materials used in phase-change applications. This sound atomic scale insight should open new avenues for the understanding of phase-change materials and other complex amorphous materials from the viewpoint of rigidity.

Transport properties of fission product vapors

International Nuclear Information System (INIS)

Im, K.H.; Ahluwalia, R.K.

1983-07-01

Kinetic theory of gases is used to calculate the transport properties of fission product vapors in a steam and hydrogen environment. Provided in tabular form is diffusivity of steam and hydrogen, viscosity and thermal conductivity of the gaseous mixture, and diffusivity of cesium iodide, cesium hydroxide, diatomic tellurium and tellurium dioxide. These transport properties are required in determining the thermal-hydraulics of and fission product transport in light water reactors

Design and construction of a prototype to obtain TeO2

International Nuclear Information System (INIS)

Roque H, I.

1997-01-01

At the National Institute of Nuclear Research is developed the process to produce the radioisotope Iodine 131 which is employed in medicine with therapeutical purposes. The raw material to produce iodine 131 is tellurium dioxide (TeO 2 ). TeO 2 is intended to be produced from a prototype being this aim of this thesis named D esign and construction of a prototype to obtain TeO 2 . The TeO 2 obtained must have specific physicochemical characteristics, being necessary an special design of a prototype which will guarantee the quality of tellurium dioxide obtention. Design and building the final prototype project, was developed in to three stages. At the first stage, the TeO 2 was obtained at the laboratory, this allows to know the basic reaction characteristics. The second stage purpose, was to work with an former prototype which allowed to produce 100 g of tellurium dioxide. In the last stage a depurated chemical process parameters was made and the prototype was refined in regard to its mechanical design, giving us as result the final prototype. With this final prototype, the production reaches 2 Kg/week of tellurium dioxide with the best physicochemical properties which is to be employed as raw material in order to produce iodine 131. (Author)

Out-of-pile experiments of fuel-cladding chemical interaction, (2)

International Nuclear Information System (INIS)

Konashi, Kenji; Yato, Tadao; Kaneko, Hiromitsu; Honda, Yutaka

1980-01-01

Cesium seems to be one of the most important fission products in the fuel-cladding chemical interaction of fuel pins for LMFBRs. However the FCCI under irradiation cannot always be explained by considering only cesium-oxygen system as the corrosive, since attack does not occur in the cesium-oxygen system unless oxygen potential is sufficiently high. Cesium-tellurium-oxygen system has been proposed to account for heavy cladding attack which was sometimes found in hypostoichiometric mixed oxide fuel pins. In this paper, the experiment on the reaction of liquid tellurium with stainless steel is reported. The type 316 stainless steel claddings for Monju type fuel pins were used as the test specimens. Tellurium was contained into the cladding tubes with end plugs. The temperature dependence of the attack by tellurium was examined in the range from 450 to 900 deg C for 30 min, and the heating time dependence was examined from 5 min to 200 hr at 725 deg C. An infrared lamp furnace was used for the experiment within 7 hr, and a resistance furnace for longer experiment. The character of corrosion was matrix attack, and the reaction products on the stainless steel surfaces consisted of chrome rich inner phase and iron and nickel rich outer phase. The results are reported. (Kako, I.)

Terahertz and infrared transmission of an organic/inorganic hybrid thermoelectric material

International Nuclear Information System (INIS)

Heyman, J. N.; Alebachew, B. A.; Kaminski, Z. S.; Nguyen, M. D.; Coates, N. E.; Urban, J. J.

2014-01-01

We report terahertz and infrared transmission measurements of a high-performance thermoelectric material containing tellurium nanowires in a conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) matrix. The DC electrical conductivity of the hybrid material (41 S/cm) is approximately one hundred times that of pure PEDOT:PSS and more than 400 times that of a film of pure tellurium nanowires, while the terahertz-frequency (THz) conductivity of PEDOT:PSS and the hybrid material are comparable at f ∼ 2THz. A frequency-dependent conductivity model indicates that the increased DC conductivity of the hybrid material results from an increase in the DC charge mobility rather than in the free charge density. We suggest that the increased DC conductivity of the hybrid material results from an increase in linkage between PEDOT domains by the tellurium nanowires

Terahertz and infrared transmission of an organic/inorganic hybrid thermoelectric material

Energy Technology Data Exchange (ETDEWEB)

Heyman, J. N., E-mail: heyman@macalester.edu; Alebachew, B. A.; Kaminski, Z. S.; Nguyen, M. D. [Physics Department, Macalester College, St. Paul, Minnesota 55105 (United States); Coates, N. E.; Urban, J. J. [The Molecular Foundry, Materials Science Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2014-04-07

We report terahertz and infrared transmission measurements of a high-performance thermoelectric material containing tellurium nanowires in a conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) matrix. The DC electrical conductivity of the hybrid material (41 S/cm) is approximately one hundred times that of pure PEDOT:PSS and more than 400 times that of a film of pure tellurium nanowires, while the terahertz-frequency (THz) conductivity of PEDOT:PSS and the hybrid material are comparable at f ∼ 2THz. A frequency-dependent conductivity model indicates that the increased DC conductivity of the hybrid material results from an increase in the DC charge mobility rather than in the free charge density. We suggest that the increased DC conductivity of the hybrid material results from an increase in linkage between PEDOT domains by the tellurium nanowires.

Occurency and aqueous processing of tellurides from Sonora (Mexico)

International Nuclear Information System (INIS)

Aguayo, S.; Perez, E.; Ecinas, M.A.

1996-01-01

Tellurium production is limited mainly to that obtained from the treatment of electrolyte muds from copper refineries. however, there are several other sources from which the precious metal tellurides are potentially attractive. This work presents a review of the main localitiesin Sonora (Mexico), where tellurides have been found. In addition, based upon the physical chemistry fundamentals for tellurium and precious metal tellurides, the aqueous extraction and recovery routes are discussed. (Author) 51 refs

Novel method of producing radioactive iodine

International Nuclear Information System (INIS)

Shikata, E.; Amano, H.

1976-01-01

Radioactive iodine(I-131) is easily obtained by heating, at a temperature ranging from 600 0 C to 650 0 C, a tellurium oxide intermediate which was obtained by heating telluric acid or tellurium trioxide at a temperature from about 400 0 C to 560 0 C and was irradited with a neutron flux. Thus, pure I-131 is obtained without the complicated operations required in a conventional process for separation and/or purification of the product. 4 claims

Single crystal growth and structure refinements of CsMxTe2-xO6 (M = Al, Ga, Ge, In) pyrochlores

International Nuclear Information System (INIS)

Siritanon, Theeranun; Sleight, A.W.; Subramanian, M.A.

2011-01-01

Graphical abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown and structure refinements indicate deviations from ideal stoichiometry presumably related to mixed valency of tellurium. Highlights: → Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown. → Structure refinements from single crystal X-ray diffraction data confirm e structure. → Deviations from ideal stoichiometry suggest mixed valency of tellurium and hence conductivity. -- Abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown from a TeO 2 flux. Structure refinements from single crystal X-ray diffraction data are reported. These results are used to discuss deviations from ideal stoichiometry that result in electronic conductivity presumably related to mixed valency of tellurium.

Evaluation of radioactive wastes in Instituto de Energia Atomica (Sao Paulo-Brazil)

International Nuclear Information System (INIS)

Sawakuchi, R.S.

1978-01-01

An evaluation of present and future production of radioactive waste in several departments of the Instituto de Energia Atomica has been done. Taking into account this evaluation, the criteria for disposal and convenient treatment technique have been studied. The most critical form of liquid radioactive waste is that of 131 I processing because high concentration of radiotellurium always accompanies this form of waste. Ion exchange and precipitation techniques were used to study this waste processing. Two kinds of resins were used by the ion exchange method: the strong anionic and the stron cationic. Quantitative tellurium retention has not been attained by the ion exchange method using either resins. The technique of precipitation of radioactive tellurium as ammonium tellurate was also used, allowing us to obtain more than 99% of tellurium removal. The remaining radioactive wastes can be eliminated using the storage for decay criteria with further release to the sewers in the case of liquids and burial in the case of solids. (Author) [pt

Thermoelectric properties of P-type Sb2Te3 thick film processed by a screen-printing technique and a subsequent annealing process

International Nuclear Information System (INIS)

Kim, Sun Jin; We, Ju Hyung; Kim, Jin Sang; Kim, Gyung Soo; Cho, Byung Jin

2014-01-01

Highlights: • We report on thermoelectric properties of screen-printed Sb 2 Te 3 thick film. • Subsequent annealing process determines thermoelectric properties of Sb 2 Te 3 film. • Annealing in tellurium powder ambient contributes to tellurium-rich Sb 2 Te 3 film. • Annealing in tellurium powder ambient enhances carrier mobility of Sb 2 Te 3 film. -- Abstract: We herein report the thermoelectric properties of Sb 2 Te 3 thick film fabricated by a screen-printing technique and a subsequent annealing process. Each step of the screen-printing fabrication process of Sb 2 Te 3 thick film is described in detail. It was found that the subsequent annealing process must be carefully designed to achieve good thermoelectric properties of the screen-printed film. The results show that the annealing of the screen-printed Sb 2 Te 3 thick film together with tellurium powder in the same process chamber significantly improves the carrier mobility by increasing the average scattering time of the carrier in the film, resulting in a large improvement of the power factor. By optimizing the annealing process, we achieved a maximum thermoelectric figure-of-merit, ZT, of 0.32 at room temperature, which is slightly higher than that of bulk Sb 2 Te 3 . Because screen-printing is a simple and low-cost process and given that it is easy to scale up to large sizes, this result will be useful for the realization of large, film-type thermoelectric devices

Communication complexity and information complexity

Science.gov (United States)

Pankratov, Denis

Information complexity enables the use of information-theoretic tools in communication complexity theory. Prior to the results presented in this thesis, information complexity was mainly used for proving lower bounds and direct-sum theorems in the setting of communication complexity. We present three results that demonstrate new connections between information complexity and communication complexity. In the first contribution we thoroughly study the information complexity of the smallest nontrivial two-party function: the AND function. While computing the communication complexity of AND is trivial, computing its exact information complexity presents a major technical challenge. In overcoming this challenge, we reveal that information complexity gives rise to rich geometrical structures. Our analysis of information complexity relies on new analytic techniques and new characterizations of communication protocols. We also uncover a connection of information complexity to the theory of elliptic partial differential equations. Once we compute the exact information complexity of AND, we can compute exact communication complexity of several related functions on n-bit inputs with some additional technical work. Previous combinatorial and algebraic techniques could only prove bounds of the form theta( n). Interestingly, this level of precision is typical in the area of information theory, so our result demonstrates that this meta-property of precise bounds carries over to information complexity and in certain cases even to communication complexity. Our result does not only strengthen the lower bound on communication complexity of disjointness by making it more exact, but it also shows that information complexity provides the exact upper bound on communication complexity. In fact, this result is more general and applies to a whole class of communication problems. In the second contribution, we use self-reduction methods to prove strong lower bounds on the information

Aspects of a Distinct Cytotoxicity of Selenium Salts and Organic Selenides in Living Cells with Possible Implications for Drug Design

Directory of Open Access Journals (Sweden)

Ethiene Castellucci Estevam

2015-07-01

Full Text Available Selenium is traditionally considered as an antioxidant element and selenium compounds are often discussed in the context of chemoprevention and therapy. Recent studies, however, have revealed a rather more colorful and diverse biological action of selenium-based compounds, including the modulation of the intracellular redox homeostasis and an often selective interference with regulatory cellular pathways. Our basic activity and mode of action studies with simple selenium and tellurium salts in different strains of Staphylococcus aureus (MRSA and Saccharomyces cerevisiae indicate that such compounds are sometimes not particularly toxic on their own, yet enhance the antibacterial potential of known antibiotics, possibly via the bioreductive formation of insoluble elemental deposits. Whilst the selenium and tellurium compounds tested do not necessarily act via the generation of Reactive Oxygen Species (ROS, they seem to interfere with various cellular pathways, including a possible inhibition of the proteasome and hindrance of DNA repair. Here, organic selenides are considerably more active compared to simple salts. The interference of selenium (and tellurium compounds with multiple targets could provide new avenues for the development of effective antibiotic and anticancer agents which may go well beyond the traditional notion of selenium as a simple antioxidant.

Forming Glasses from Se and Te

Directory of Open Access Journals (Sweden)

Pierre Lucas

2009-10-01

Full Text Available Despite being close neighbors on the Periodic Table, selenium and tellurium present a totally different abilities to form glasses. Se is a very good glass former, and gives rise to numerous glass compositions which are popular for their transparency in the infrared range and their stability against crystallization. These glasses can be shaped into sophisticated optical devices such as optical fibers, planar guides or lenses. Nevertheless, their transparencies are limited at about 12 μm (depending on the thickness of the optical systems due to the relatively small mass of the Se element. On the other hand, tellurium is heavier and its use in substitution for Se permits to shift the IR cutoff beyond 20 μm. However, the semimetallic nature of Te limits its glass formation ability and this glass family is known to be unstable and consequently has found application as phase change material in the Digital Versatile Disk (DVD technology. In this paper, after a review of selenide glasses and their applications, it will be shown how, in a recent past, it has been possible to stabilize tellurium glasses by introducing new elements like Ga or I in their compositions.

The crystal chemistry of novel thorium and uranium compounds with oxo-anions from group VI of periodic table (S, Se, Te, Cr, Mo and W)

Energy Technology Data Exchange (ETDEWEB)

Xiao, Bin

2016-01-26

This dissertation focus on the synthesis, phase studies and physicochemical properties of novel thorium and uranium compounds with the Group VI (S, Se, Te, Cr, Mo, W) of the Periodic Table. All the studied compounds are listed in Table 2.2 from the page 15. I subdivided all the newly synthesized compounds into several chapters according to their structural and topological differences. First, for thorium molybdates and tungstates, almost all of these compounds are based on corner-sharing of ThO{sub x} (x = 6, 8 and 9) and MoO{sub 4} or WO{sub x} (x = 4, 5, 6) polyhedra. Interestingly, all these compounds can be seen as derived from a pure thorium molybdate compound (ThMo{sub 2}O{sub 8}) which was isolated from high-temperature solid-state synthesis method. Therefore, the polymorphs of this most basic ThMo{sub 2}O{sub 8} compound is firstly introduced (see Chapter 3.1 from page 18). The thermodynamic, electronic and vibrational properties of all investigated ThMo{sub 2}O{sub 8} polymorphs were studied using ab initio calculations. Then, two subfamilies of thorium molybdates, that is, rubidium thorium molybdate and cesium thorium molybdate and their thermal and vibrational behaviors were discussed in details in Chapter 4.1 from page 37 and Chapter 4.2 from page 50, respectively. Moreover, some new insights about the complexity of thorium tungstates were also discussed (Chapter 4.3 from page 59). Some novel thorium molybdate and chromate compounds synthesized from aqueous condition are discussed in Chapter 5 from page 71. In the Chapter 8.2.4, the stereochemistry for thorium and uranium compounds are introduced, especially thorium selinites and uranyl tellurites (see Chapter 6.1 from page 82), thorium tellurites (Chapter 6.2 from page 93), and uranyl tellurites (Chapter 6.3 from page 99 for sodium uranyl tellurium and Chapter 6.4 from page 110 for potassium uranyl tellurium, respectively). In the actinide tellurium systems, additional MoO{sub 3}/WO{sub 3} were also

Rare (Earth Elements [score

Directory of Open Access Journals (Sweden)

Camilo Méndez

2014-12-01

Full Text Available Rare (Earth Elements is a cycle of works for solo piano. The cycle was inspired by James Dillon’s Book of Elements (Vol. I-V. The complete cycle will consist of 14 pieces; one for each selected rare (earth element. The chosen elements are Neodymium, Erbium, Tellurium, Hafnium, Tantalum, Technetium, Indium, Dysprosium, Lanthanium, Cerium, Europium, Terbium, Yttrium and Darmstadtium. These elements were selected due to their special atomic properties that in many cases make them extremely valuable for the development of new technologies, and also because of their scarcity. To date, only 4 works have been completed Yttrium, Technetium, Indium and Tellurium.

Anisotropic Light Diffraction by Ultrasound in Crystals with Strong Acoustic Anisotropy

Science.gov (United States)

Voloshin, Andrey S.; Balakshy, Vladimir I.

In modern acousto-optics, crystalline materials are used predominantly for manufacturing acousto-optic instruments. Among these materials, such crystals as paratellurite, tellurium, calomel, TAS and some others occupy a prominent place, which are distinguished by exceptionally large anisotropy of acoustic properties. In this work, the influence of acoustic beam energy walk-off on characteristics of Bragg diffraction of light is studied by the example of tellurium crystal. It is shown that the walk-off can substantially change angular and frequency ranges, resulting in their narrowing or broadening subject to position of the operating point in the Bragg angle frequency characteristic. Coefficients of broadening are introduced for characterization of this effect.

Phase relations in the Cu-Te-S system at temperatures between 350 and 900 degree C

DEFF Research Database (Denmark)

Karup-Møller, Sven

1994-01-01

data and optical data on phases A and B are listed. At 350 degree C there exist two liquid fields which at 450 degree C have become one continuous field stretching from Cu45Te55 with low S content to the tellurium corner of the phase diagram and from there to the sulphur corner. With increasing S......, the Cu content of the liquid rapidly decreases to trace amonts. With increasing temperature the field extends into the ternary from the tellurium corner towards the Cu-S join. The boundary of the liquid field in the central portion of the phae diagram towards the sulphur corner does not change position...

Segregation of the elements of the platinum group in a simulated high-level waste glass

International Nuclear Information System (INIS)

Mitamura, H.; Banba, T.; Kamizono, H.; Kiriyama, Y.; Kumata, M.; Murakami, T.; Tashiro, S.

1983-01-01

Segregation of the elements of the platinum group occurred during vitrification of the borosilicate glass containing 20 wt% simulated high-level waste oxides. The segregated materials were composed of two crystalline phases: one was the solid solution of ruthenium and rhodium dioxides and the other was that of palladium and rhodium metals also with tellurium. The segregated materials were not distributed homogeneously throughout the glass: (i) on the surface of the glass, there occurred palladium, rhodium and tellurium alloy alone; and (ii) at the inner part of the glass, the agglomerates of the two phases were concentrated in one part and dispersed in the other

Reactive ion etching of tellurite and chalcogenide waveguides using hydrogen, methane, and argon

International Nuclear Information System (INIS)

Vu, K. T.; Madden, S. J.

2011-01-01

The authors report in detail on the reactive plasma etching properties of tellurium and demonstrate a high quality etching process using hydrogen, methane, and argon. Very low loss planar ridge waveguides are demonstrated. Optical losses in tellurium dioxide waveguides below 0.1 dB/cm in most of the near infrared region of the electromagnetic spectrum and at 1550 nm have been achieved--the lowest ever reported by more than an order of magnitude and clearly suitable for planar integrated devices. The etch process is also shown to be suitable for chalcogenide glasses which may be of importance in applications such as phase change memory devices and nonlinear integrated optics.

Combustion synthesis and characterization of uranium and thorium tellurides

International Nuclear Information System (INIS)

Czechowicz, D.G.

1985-10-01

This report describes an investigation of the chemical systems uranium-tellurium and thorium-tellurium. A novel synthesis technique, combustion synthesis, which uses the exothermic heat of reaction rather than externally supplied heat, was utilized to form the phases UTe, U 3 Te 4 , and UTe 2 in the U-Te system and the phases ThTe, Th 2 Te 3 , and ThTe 2 in the Th-Te system from reactions of the type U/sub x/ + Te/sub y/ = U/sub x/Te/sub y/. With this synthetic method, U-Te and Th-Te products could be formed in a matter of seconds, and the purity of the products was often greater than that of the starting materials used. Control over final product stoichiometry was found to be very difficult. The product phase distribution observed in combustion products, as determined by x-ray diffraction, electron microprobe, and optical metallographic methods, was found to be spatially complex. Lattice constants were calculated from x-ray diffraction patterns for the compounds UTe, U 3 Te 4 , and ThTe. SOLGASMIX thermodynamic equilibrium calculations were performed using available and estimated thermodynamic data on the system U-Te-O in an attempt to understand the products formed by combustion. Adiabatic combustion reaction temperatures for specific U-Te and Th-Te reactions were also calculated utilizing available and estimated thermodynamic data. 71 refs., 31 figs., 15 tabs

Fabrication of Te and Te-Au Nanowires-Based Carbon Fiber Fabrics for Antibacterial Applications

Directory of Open Access Journals (Sweden)

Ting-Mao Chou

2016-02-01

Full Text Available Pathogenic bacteria that give rise to diseases every year remain a major health concern. In recent years, tellurium-based nanomaterials have been approved as new and efficient antibacterial agents. In this paper, we developed the approach to directly grow tellurium nanowires (Te NWs onto commercial carbon fiber fabrics and demonstrated their antibacterial activity. Those Te NWs can serve as templates and reducing agents for gold nanoparticles (Au NPs to deposit. Three different Te-Au NWs with varied concentration of Au NPs were synthesized and showed superior antibacterial activity and biocompability. These results indicate that the as-prepared carbon fiber fabrics with Te and Te-Au NWs can become antimicrobial clothing products in the near future.

Galvano-magnetic properties and Shubnikov de Haas effect of Te-whiskers

International Nuclear Information System (INIS)

Berezovets, Veacheslav; Bondarchuk, Nikolai; Nikolaeva, Albina; Nijankovskii, Victor

2009-01-01

The work is devoted to investigation of the peculiarities of magnetoresistance, Hall effect and Shubnikov de Haas oscillations in Te-whiskers. Te-whiskers was prepared from vapor-gas phase on the substrate pure tellurium and grown naturally, of the walls of a crucible in the course of growing Te single crystals by the Czochralski method . The measurements of the galvanomagnetic properties and Shubnikov de Haas oscillation correspond to the notion of the occurrence of the effect of intraband magnetic breakdown when two different quasi-classical cyclotron trajectories coexist simultaneously in a magnetic field. This effect is a consequence of the presence of the saddle point in the dispersion law of the tellurium valence band. (authors)

Flexible screen printed thick film thermoelectric generator with reduced material resistivity

International Nuclear Information System (INIS)

Cao, Z; Koukharenko, E; Torah, R N; Tudor, J; Beeby, S P

2014-01-01

This work presents a flexible thick-film Bismuth Tellurium/Antimony Tellurium (BiTe/SbTe) thermoelectric generator (TEG) with reduced material resistivity fabricated by screen printing technology. Cold isostatic pressing (CIP) was introduced to lower the resistivity of the printed thermoelectric materials. The Seebeck coefficient (α) and the resistivity (ρ) of printed materials were measured as a function of applied pressure. A prototype TEG with 8 thermocouples was fabricated on flexible polyimide substrate. The dimension of a single printed element was 20 mm × 2 mm × 78.4 pm. The coiled-up prototype produced a voltage of 36.4 mV and a maximum power of 40.3 nW from a temperature gradient of 20 °C

Non-destructive local determination of doping additions and main components in single crystals

International Nuclear Information System (INIS)

Ehksperiandova, L.P.; Blank, A.B.; Kukhtina, N.N.; Afanasiadi, L.I.

1994-01-01

Procedures for local non-destructive determination of elements in optical and scintillation single crystals are developed. They are applied for determination of the main components (in cadmium tungstate) and doping additions (tellurium in zinc selenide, europium in gadolinium silicate). The metrological characteristics of the developed micro-analysis methods are estimated. Segregation of the main components and doping additions in the objects under consideration are investigated. Tellurium is found to be distributed uniformly on the cross-sections of bulk zinc selenide single crystals. The segregation of europium along gadolinium silicate ingots is almost absent. On the cross-section surface of cadmium tungstate single crystals the microregions are found characterized by the prevailing contents of cadmium or tungsten

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow

Sorption of V and VI group metalloids (As, Sb, Te on modified peat sorbents

Directory of Open Access Journals (Sweden)

Ansone-Bertina Linda

2016-01-01

Full Text Available The present work investigates arsenic, antimony and tellurium sorption using iron modified peat. The results were obtained using batch tests and the sorption was studied as a function of initial metalloid concentration, pH and sorption time, as well as the presence of competing substances. The obtained results indicate that modification of peat with Fe compounds significantly enhances the sorption capacity of the sorbents used for sorption of arsenic, antimony and tellurium. The optimal pH interval for the sorption of Sb(III is 6.5–9 and for As(V and Sb(V – 3–6, while As(III and tellurium sorption using Fe-modified peat is favourable in a wider interval of 3–9. The presence of competing ions as well as HA affect sorption of metalloids on Fe-modified peat. A minor impact on the reduction of metalloid sorption was detected in the presence of nitrate, sulphate, carbonate and tartrate ions, while in the presence of phosphate and HA the sorption ability of metalloids can be considerably reduced. The obtained results of kinetic experiments indicate that sorption of metalloids on Fe-modified peat mainly occurs relying on mechanisms of physical sorption processes.

Molecular polarizability of organic molecules and their complexes. Communication LIV. Molar volumes of polyaryl organoelement compounds in solutions, extrapolated to infinite dilution, and steric structure of the molecules

International Nuclear Information System (INIS)

Bulgarevich, S.B.; Burdastykh, T.V.

2008-01-01

Molar volumes in various solvents were determined for organic derivatives of silicon, phosphorus, arsenic, sulfur, and tellurium, containing aryl nuclei capable to internal rotation about single bonds between them and bridging groups. Additive analysis of the molar volumes of these compounds showed that the aryl nuclei are acoplanar with respect to the bridging groups. Most probable is a conrotatory mutual orientation of the aromatic rings. Molar volumes were also determined for a series of compounds with two bridging groups, which can serve as models of an extreme case of mutual proximity of aryl ring planes in diaryl systems with one bridging group. A possibility for considerably simplifying the methods for determination of dipole moments and Kerr constants for compounds whose molar volumes can be calculated by our developed additive scheme is demonstrated [ru

Complex chemistry

International Nuclear Information System (INIS)

Kim, Bong Gon; Kim, Jae Sang; Kim, Jin Eun; Lee, Boo Yeon

2006-06-01

This book introduces complex chemistry with ten chapters, which include development of complex chemistry on history coordination theory and Warner's coordination theory and new development of complex chemistry, nomenclature on complex with conception and define, chemical formula on coordination compound, symbol of stereochemistry, stereo structure and isomerism, electron structure and bond theory on complex, structure of complex like NMR and XAFS, balance and reaction on solution, an organo-metallic chemistry, biology inorganic chemistry, material chemistry of complex, design of complex and calculation chemistry.

Structural and Optothermal Properties of Iron Ditelluride Layered Structures in the Framework of the Lattice Compatibility Theory

Directory of Open Access Journals (Sweden)

K. Ben Messaoud

2014-01-01

Full Text Available This study concerns structural and optothermal properties of iron ditelluride layered structures which were fabricated via a low-cost protocol. The main precursors were FeCl3 · 6H2O and Fe2O3. After a heat treatment within a tellurium-rich medium at various temperatures (470°C, 500°C, and 530°C during 24 h, classical analyses have been applied to the iron ditelluride layered structures. A good crystalline state with a preferential orientation of the crystallites along (111 direction has been recorded. Moreover, additional opto-thermal investigation and analyses within the framework of the Lattice Compatibility Theory gave plausible explanation for prompt temperature-dependent incorporation of tellurium element inside hematite elaborated matrices.

Anomalous behavior of tellurium abundances

Energy Technology Data Exchange (ETDEWEB)

Cohen, B L

1984-01-01

The cosmic abundance of Te is larger than for any element with atomic number greater than 40, but it is one of the least abundant elements in the earth's lithosphere and it is one of the five elements never reported in sea water. On the other hand, it is the fourth most abundant element in the human body (after Fe, Zn and Rb), and is unusually abundant in human food. It is shown that the high abundance in human food combined with the low abundance in soil requires that it be picked up by plant roots very much more efficiently than any other trace element.

Resonant ionization by laser beams: application to ions sources and to study the nuclear structure of radioactive tellurium isotopes; Ionisation resonante par faisceaux laser: application aux sources d'ions et a l'etude de la structure des noyaux radioactifs de tellure

Energy Technology Data Exchange (ETDEWEB)

Sifi, R

2007-07-15

The radioactive ion beams that are produced through current isotope separators are well separated according to the A mass but not according to the Z parameter. The resonant ionization through laser beams applied to ion sources allows the production of radioactive ion beam in a very selective and efficient way by eliminating the isobaric contamination. The first chapter is dedicated to the resonant ionization by laser beams, we describe the principle, the experimental setting, the lasers used, the ionization schemes and the domain of application. The second chapter deals with the application of resonant ionization to laser ion sources for the production of radioactive ion beams. We present experimental tests performed for getting copper ion beams. Resonant ionization through laser is also used in the spectroscopy experiments performed at the Isolde (isotope separation on-line device) installation in CERN where more than 20 elements are ionized very efficiently. The technique is based on a frequency scanning around the excitation transition of the atoms in order to probe the hyperfine structure. Laser spectroscopy allows the determination of the hyperfine structure as well as the isotopic shift of atoms. In the third chapter the method is applied to the spectroscopy of tellurium atoms. First, we define the 2 parameters on which the extraction is based: charge radius and nuclear moments, then we present several theoretical models that we have used to assess our experimental results. (A.C.)

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis

OpenAIRE

Chen, Tianfeng; Yang,Fang; Wong,Ka-Hing; Yang,Yufeng; Li,Xiaoling; Jiang,Jie; Wu,Hualian; Zheng,Wenjie

2014-01-01

Fang Yang,1 Ka-Hing Wong,2 Yufeng Yang,3 Xiaoling Li,1 Jie Jiang,1 Wenjie Zheng,1 Hualian Wu,1 Tianfeng Chen1 1Department of Chemistry, Jinan University, Guangzhou, People’s Republic of China; 2Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hong Kong, People’s Republic of China; 3Institute of Hydrobiology, College of Life Science and Technology, Jinan University, Guangzhou, People’s Republic of China Abstract: Tellu...

Proceedings 43rd Stanford Geothermal Workshop

Energy Technology Data Exchange (ETDEWEB)

Simmons, Stuart; Kirby, Stefan; Verplanck, Philip; Kelley, Karen

2018-02-12

Herein we summarize the results of an investigation dealing with the concentrations and inventories of strategic, critical and valuable materials (SCVM) in produced fluids from geothermal and hydrocarbon reservoirs (50-250° C) in Nevada and Utah. Water samples were collected from thirty-four production wells across eight geothermal fields, the Uinta Basin oil/gas province in northeast Utah, and the Covenant oil field in southwestern Utah; additional water samples were collected from six hot springs in the Sevier Thermal Belt in southwestern Utah. Most SCVM concentrations in produced waters range from <0.1 to 100 µg/kg; the main exception is lithium, which has concentrations that range from <1000 to 25,000 ug/kg. Relatively high concentrations of gallium, germanium, scandium, selenium, and tellurium are measured too. Geothermal waters contain very low concentrations of REEs, below analytical detections limits (0.01 µg/kg), but the concentrations of lanthanum, cerium, and europium range from 0.05 to 5 µg/kg in Uinta basin waters. Among the geothermal fields, the Roosevelt Hot Spring reservoir appears to have the largest inventories of germanium and lithium, and Patua appears to have the largest inventories of gallium, scandium, selenium, and tellurium. By comparison, the Uinta basin has larger inventories of gallium. The concentrations of gallium, germanium, lithium, scandium, selenium, and tellurium in produced waters appear to be partly related to reservoir temperature and concentrations of total dissolved salts. The relatively high concentration and large inventory of lithium occurring at Roosevelt Hot Springs may be related to granitic-gneissic crystalline rocks, which host the reservoir. Analyses of calcite scales from Dixie Valley indicate enrichments in cobalt, gallium, gold, palladium, selenium and tellurium, and these metals appear to be depositing at deep levels in production wells due to boiling. Comparisons with SCVM mineral deposits suggest that

ComplexViewer: visualization of curated macromolecular complexes.

Science.gov (United States)

Combe, Colin W; Sivade, Marine Dumousseau; Hermjakob, Henning; Heimbach, Joshua; Meldal, Birgit H M; Micklem, Gos; Orchard, Sandra; Rappsilber, Juri

2017-11-15

Proteins frequently function as parts of complexes, assemblages of multiple proteins and other biomolecules, yet network visualizations usually only show proteins as parts of binary interactions. ComplexViewer visualizes interactions with more than two participants and thereby avoids the need to first expand these into multiple binary interactions. Furthermore, if binding regions between molecules are known then these can be displayed in the context of the larger complex. freely available under Apache version 2 license; EMBL-EBI Complex Portal: http://www.ebi.ac.uk/complexportal; Source code: https://github.com/MICommunity/ComplexViewer; Package: https://www.npmjs.com/package/complexviewer; http://biojs.io/d/complexviewer. Language: JavaScript; Web technology: Scalable Vector Graphics; Libraries: D3.js. colin.combe@ed.ac.uk or juri.rappsilber@ed.ac.uk. © The Author 2017. Published by Oxford University Press.

Electrochemical Deposition of CdTe Semiconductor Thin Films for Solar Cell Application Using Two-Electrode and Three-Electrode Configurations: A Comparative Study

Directory of Open Access Journals (Sweden)

O. K. Echendu

2016-01-01

Full Text Available Thin films of CdTe semiconductor were electrochemically deposited using two-electrode and three-electrode configurations in potentiostatic mode for comparison. Cadmium sulphate and tellurium dioxide were used as cadmium and tellurium sources, respectively. The layers obtained using both configurations exhibit similar structural, optical, and electrical properties with no specific dependence on any particular electrode configuration used. These results indicate that electrochemical deposition (electrodeposition of CdTe and semiconductors in general can equally be carried out using two-electrode system as well as the conventional three-electrode system without compromising the essential qualities of the materials produced. The results also highlight the advantages of the two-electrode configuration in process simplification, cost reduction, and removal of a possible impurity source in the growth system, especially as the reference electrode ages.

Charge transport properties of CdMnTe radiation detectors

Energy Technology Data Exchange (ETDEWEB)

Kim K.; Rafiel, R.; Boardman, M.; Reinhard, I.; Sarbutt, A.; Watt, G.; Watt, C.; Uxa, S.; Prokopovich, D.A.; Belas, E.; Bolotnikov, A.E.; James, R.B.

2012-04-11

Growth, fabrication and characterization of indium-doped cadmium manganese telluride (CdMnTe)radiation detectors have been described. Alpha-particle spectroscopy measurements and time resolved current transient measurements have yielded an average charge collection efficiency approaching 100 %. Spatially resolved charge collection efficiency maps have been produced for a range of detector bias voltages. Inhomogeneities in the charge transport of the CdMnTe crystals have been associated with chains of tellurium inclusions within the detector bulk. Further, it has been shown that the role of tellurium inclusions in degrading chargecollection is reduced with increasing values of bias voltage. The electron transit time was determined from time of flight measurements. From the dependence of drift velocity on applied electric field the electron mobility was found to be n = (718 55) cm2/Vs at room temperature.

Synchronization in node of complex networks consist of complex chaotic system

Energy Technology Data Exchange (ETDEWEB)

Wei, Qiang, E-mail: qiangweibeihua@163.com [Beihua University computer and technology College, BeiHua University, Jilin, 132021, Jilin (China); Digital Images Processing Institute of Beihua University, BeiHua University, Jilin, 132011, Jilin (China); Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian, 116024 (China); Xie, Cheng-jun [Beihua University computer and technology College, BeiHua University, Jilin, 132021, Jilin (China); Digital Images Processing Institute of Beihua University, BeiHua University, Jilin, 132011, Jilin (China); Liu, Hong-jun [School of Information Engineering, Weifang Vocational College, Weifang, 261041 (China); Li, Yan-hui [The Library, Weifang Vocational College, Weifang, 261041 (China)

2014-07-15

A new synchronization method is investigated for node of complex networks consists of complex chaotic system. When complex networks realize synchronization, different component of complex state variable synchronize up to different scaling complex function by a designed complex feedback controller. This paper change synchronization scaling function from real field to complex field for synchronization in node of complex networks with complex chaotic system. Synchronization in constant delay and time-varying coupling delay complex networks are investigated, respectively. Numerical simulations are provided to show the effectiveness of the proposed method.

Control of interferences in the analysis of low-concentration I 129

International Nuclear Information System (INIS)

Quintana, Eduardo E.; Thyssen, Sandra M.

1999-01-01

Traces of uranium, cesium and tellurium interfere in the determination of I 129 by neutron activation analysis. The paper describes the procedures used to control or eliminate the interferences in the different steps of the analysis

Investigating body function

International Nuclear Information System (INIS)

Monks, R.; Riley, A.L.M.

1981-01-01

This invention relates to the investigation of body function, especially small bowel function but also liver function, using bile acids and bile salts or their metabolic precursors labelled with radio isotopes and selenium or tellurium. (author)

Generalized Combination Complex Synchronization for Fractional-Order Chaotic Complex Systems

Directory of Open Access Journals (Sweden)

Cuimei Jiang

2015-07-01

Full Text Available Based on two fractional-order chaotic complex drive systems and one fractional-order chaotic complex response system with different dimensions, we propose generalized combination complex synchronization. In this new synchronization scheme, there are two complex scaling matrices that are non-square matrices. On the basis of the stability theory of fractional-order linear systems, we design a general controller via active control. Additionally, by virtue of two complex scaling matrices, generalized combination complex synchronization between fractional-order chaotic complex systems and real systems is investigated. Finally, three typical examples are given to demonstrate the effectiveness and feasibility of the schemes.

Complexity explained

CERN Document Server

Erdi, Peter

2008-01-01

This book explains why complex systems research is important in understanding the structure, function and dynamics of complex natural and social phenomena. Readers will learn the basic concepts and methods of complex system research.

Comparative study on the bioactivation mechanisms and cytotoxicity of Te-phenyl-L-tellurocysteine, Se-phenyl-L-selenocysteine, and S-phenyl-L-cysteine

NARCIS (Netherlands)

Rooseboom, Martijn; Vermeulen, Nico P E; Durgut, Fatma; Commandeur, Jan N M

2002-01-01

Tellurium compounds are effective antioxidants and chemoprotectors, even more active than their selenium and sulfur analogues. In addition to these properties, some selenium compounds, such as selenocysteine Se-conjugates, possess significant chemopreventive and antitumor activities, and selenol

On Measuring the Complexity of Networks: Kolmogorov Complexity versus Entropy

Directory of Open Access Journals (Sweden)

Mikołaj Morzy

2017-01-01

Full Text Available One of the most popular methods of estimating the complexity of networks is to measure the entropy of network invariants, such as adjacency matrices or degree sequences. Unfortunately, entropy and all entropy-based information-theoretic measures have several vulnerabilities. These measures neither are independent of a particular representation of the network nor can capture the properties of the generative process, which produces the network. Instead, we advocate the use of the algorithmic entropy as the basis for complexity definition for networks. Algorithmic entropy (also known as Kolmogorov complexity or K-complexity for short evaluates the complexity of the description required for a lossless recreation of the network. This measure is not affected by a particular choice of network features and it does not depend on the method of network representation. We perform experiments on Shannon entropy and K-complexity for gradually evolving networks. The results of these experiments point to K-complexity as the more robust and reliable measure of network complexity. The original contribution of the paper includes the introduction of several new entropy-deceiving networks and the empirical comparison of entropy and K-complexity as fundamental quantities for constructing complexity measures for networks.

Complex dynamical invariants for two-dimensional complex potentials

Indian Academy of Sciences (India)

Abstract. Complex dynamical invariants are searched out for two-dimensional complex poten- tials using rationalization method within the framework of an extended complex phase space characterized by x = x1 + ip3, y = x2 + ip4, px = p1 + ix3, py = p2 + ix4. It is found that the cubic oscillator and shifted harmonic oscillator ...

Complex Fuzzy Set-Valued Complex Fuzzy Measures and Their Properties

Science.gov (United States)

Ma, Shengquan; Li, Shenggang

2014-01-01

Let F*(K) be the set of all fuzzy complex numbers. In this paper some classical and measure-theoretical notions are extended to the case of complex fuzzy sets. They are fuzzy complex number-valued distance on F*(K), fuzzy complex number-valued measure on F*(K), and some related notions, such as null-additivity, pseudo-null-additivity, null-subtraction, pseudo-null-subtraction, autocontionuous from above, autocontionuous from below, and autocontinuity of the defined fuzzy complex number-valued measures. Properties of fuzzy complex number-valued measures are studied in detail. PMID:25093202

The complex portal--an encyclopaedia of macromolecular complexes.

Science.gov (United States)

Meldal, Birgit H M; Forner-Martinez, Oscar; Costanzo, Maria C; Dana, Jose; Demeter, Janos; Dumousseau, Marine; Dwight, Selina S; Gaulton, Anna; Licata, Luana; Melidoni, Anna N; Ricard-Blum, Sylvie; Roechert, Bernd; Skyzypek, Marek S; Tiwari, Manu; Velankar, Sameer; Wong, Edith D; Hermjakob, Henning; Orchard, Sandra

2015-01-01

The IntAct molecular interaction database has created a new, free, open-source, manually curated resource, the Complex Portal (www.ebi.ac.uk/intact/complex), through which protein complexes from major model organisms are being collated and made available for search, viewing and download. It has been built in close collaboration with other bioinformatics services and populated with data from ChEMBL, MatrixDB, PDBe, Reactome and UniProtKB. Each entry contains information about the participating molecules (including small molecules and nucleic acids), their stoichiometry, topology and structural assembly. Complexes are annotated with details about their function, properties and complex-specific Gene Ontology (GO) terms. Consistent nomenclature is used throughout the resource with systematic names, recommended names and a list of synonyms all provided. The use of the Evidence Code Ontology allows us to indicate for which entries direct experimental evidence is available or if the complex has been inferred based on homology or orthology. The data are searchable using standard identifiers, such as UniProt, ChEBI and GO IDs, protein, gene and complex names or synonyms. This reference resource will be maintained and grow to encompass an increasing number of organisms. Input from groups and individuals with specific areas of expertise is welcome. © The Author(s) 2014. Published by Oxford University Press on behalf of Nucleic Acids Research.

Complexity Plots

KAUST Repository

Thiyagalingam, Jeyarajan

2013-06-01

In this paper, we present a novel visualization technique for assisting the observation and analysis of algorithmic complexity. In comparison with conventional line graphs, this new technique is not sensitive to the units of measurement, allowing multivariate data series of different physical qualities (e.g., time, space and energy) to be juxtaposed together conveniently and consistently. It supports multivariate visualization as well as uncertainty visualization. It enables users to focus on algorithm categorization by complexity classes, while reducing visual impact caused by constants and algorithmic components that are insignificant to complexity analysis. It provides an effective means for observing the algorithmic complexity of programs with a mixture of algorithms and black-box software through visualization. Through two case studies, we demonstrate the effectiveness of complexity plots in complexity analysis in research, education and application. © 2013 The Author(s) Computer Graphics Forum © 2013 The Eurographics Association and Blackwell Publishing Ltd.

Comparison of Se and Te clusters produced by ion bombardment

Directory of Open Access Journals (Sweden)

Trzyna Małgorzata

2017-01-01

Full Text Available Nanostructures based on tellurium and selenium are materials used as components for the manufacturing topological insulators. Therefore it is crucial to precisely characterize these materials. In this work the emission of selenium and tellurium cluster ions, sputtered by Bi+ primary ion guns, was investigated by using Time-of-Flight Secondary Ion Mass Spectrometry (TOF SIMS. It has been found that BixTex and BixSex clusters appear in addition to Sex and Tex clusters in the mass range up to ~ 1300 m/z. Local maxima or minima (magic numbers are observed in the ion intensity versus a number of atoms per cluster for both positive and negative ions spectra for all types of clusters and primary ions used. These extrema can be attributed to different yield and stability of certain clusters but also to fragmentation of high-mass clusters.

Heavily doped GaAs:Te layers grown by MOVPE using diisopropyl telluride as a source

Energy Technology Data Exchange (ETDEWEB)

Daniltsev, V. M.; Demidov, E. V.; Drozdov, M. N.; Drozdov, Yu. N., E-mail: drozdyu@ipmras.ru; Kraev, S. A.; Surovegina, E. A.; Shashkin, V. I.; Yunin, P. A. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation)

2016-11-15

The capabilities of GaAs epitaxial layers extremely heavily doped with tellurium by metal-organic vapor-phase epitaxy using diisopropyl telluride as a source are studied. It is shown that tellurium incorporation into GaAs occurs to an atomic concentration of 10{sup 21} cm{sup –3} without appreciable diffusion and segregation effects. Good carrier concentrations (2 × 10{sup 19} cm{sup –3}) and specific contact resistances of non-alloyed ohmic contacts (1.7 × 10{sup –6} Ω cm{sup 2}) give grounds to use such layers to create non-alloyed ohmic contacts in electronic devices. A sharp decrease in the electrical activity of Te atoms, a decrease in the electron mobility, and an increase in the contact resistance at atomic concentrations above 2 × 10{sup 20} cm{sup –3} are detected.

Systems and methods for the synthesis of high thermoelectric performance doped-SnTe materials

Science.gov (United States)

Ren, Zhifeng; Zhang, Qian; Chen, Gang

2018-02-27

A thermoelectric composition comprising tin (Sn), tellurium (Te) and at least one dopant that comprises a peak dimensionless figure of merit (ZT) of 1.1 and a Seebeck coefficient of at least 50 .mu.V/K and a method of manufacturing the thermoelectric composition. A plurality of components are disposed in a ball-milling vessel, wherein the plurality of components comprise tin (Sn), tellurium (Te), and at least one dopant such as indium (In). The components are subsequently mechanically and thermally processed, for example, by hot-pressing. In response to the mechanical-thermally processing, a thermoelectric composition is formed, wherein the thermoelectric composition comprises a dimensionless figure of merit (ZT) of the thermoelectric composition is at least 0.8, and wherein a Seebeck coefficient of the thermoelectric composition is at least 50 .mu.V/K at any temperature.

Calculation of 125Te NMR Chemical Shifts at the Full Four-Component Relativistic Level with Taking into Account Solvent and Vibrational Corrections: A Gateway to Better Agreement with Experiment.

Science.gov (United States)

Rusakova, Irina L; Rusakov, Yuriy Yu; Krivdin, Leonid B

2017-06-29

Four-component relativistic calculations of 125 Te NMR chemical shifts were performed in the series of 13 organotellurium compounds, potential precursors of the biologically active species, at the density functional theory level under the nonrelativistic and four-component fully relativistic conditions using locally dense basis set scheme derived from relativistic Dyall's basis sets. The relativistic effects in tellurium chemical shifts were found to be of as much as 20-25% of the total calculated values. The vibrational and solvent corrections to 125 Te NMR chemical shifts are about, accordingly, 6 and 8% of their total values. The PBE0 exchange-correlation functional turned out to give the best agreement of calculated tellurium shifts with their experimental values giving the mean absolute percentage error of 4% in the range of ∼1000 ppm, provided all corrections are taken into account.

Specific features of phase transformations in germanium monotelluride

International Nuclear Information System (INIS)

Bigvava, A.D.; Gabedava, A.A.; Kunchuliya, Eh.D.; Shvangiradze, R.R.

1981-01-01

Phase transformations in germanium monotelluride are studied . using DRON-0.5 and DRON-1 plants with high-temperature chamber GPVT-1500 at Cu, Ksub(α) radiation. It is shown that in the whole homogeneity range α GeTe is a metastable phase which is formed under the conditions of fast cooling of alloy from temperatures >=Tsub(cub) (temperature of transition in cubic crystal system). An equilibrium γ-phase is obtained by annealing of dispersed powders and metal-ceramic specimens of alloys with 50.3; 50.6; 50.9 at % Te. Lattice parameters of rhombic γ-phase do not depend on tellurium content in initial α- phase. α→γ transformation is observed at any temperature less than Tsub(cub) with the change of alloy composition, namely tellurium precipitation. γ-phase transforms into β at higher temperatures than α-phase [ru

Comparison of Se and Te clusters produced by ion bombardment

Science.gov (United States)

Trzyna, Małgorzata

2017-01-01

Nanostructures based on tellurium and selenium are materials used as components for the manufacturing topological insulators. Therefore it is crucial to precisely characterize these materials. In this work the emission of selenium and tellurium cluster ions, sputtered by Bi+ primary ion guns, was investigated by using Time-of-Flight Secondary Ion Mass Spectrometry (TOF SIMS). It has been found that BixTex and BixSex clusters appear in addition to Sex and Tex clusters in the mass range up to 1300 m/z. Local maxima or minima (magic numbers) are observed in the ion intensity versus a number of atoms per cluster for both positive and negative ions spectra for all types of clusters and primary ions used. These extrema can be attributed to different yield and stability of certain clusters but also to fragmentation of high-mass clusters.

Complex differential geometry

CERN Document Server

Zheng, Fangyang

2002-01-01

The theory of complex manifolds overlaps with several branches of mathematics, including differential geometry, algebraic geometry, several complex variables, global analysis, topology, algebraic number theory, and mathematical physics. Complex manifolds provide a rich class of geometric objects, for example the (common) zero locus of any generic set of complex polynomials is always a complex manifold. Yet complex manifolds behave differently than generic smooth manifolds; they are more coherent and fragile. The rich yet restrictive character of complex manifolds makes them a special and interesting object of study. This book is a self-contained graduate textbook that discusses the differential geometric aspects of complex manifolds. The first part contains standard materials from general topology, differentiable manifolds, and basic Riemannian geometry. The second part discusses complex manifolds and analytic varieties, sheaves and holomorphic vector bundles, and gives a brief account of the surface classifi...

(II) complexes

African Journals Online (AJOL)

activities of Schiff base tin (II) complexes. Neelofar1 ... Conclusion: All synthesized Schiff bases and their Tin (II) complexes showed high antimicrobial and ...... Singh HL. Synthesis and characterization of tin (II) complexes of fluorinated Schiff bases derived from amino acids. Spectrochim Acta Part A: Molec Biomolec.

Workshop on Recommendation in Complex Scenarios (ComplexRec 2017)

DEFF Research Database (Denmark)

Bogers, Toine; Koolen, Marijn; Mobasher, Bamshad

2017-01-01

Recommendation algorithms for ratings prediction and item ranking have steadily matured during the past decade. However, these state-of-the-art algorithms are typically applied in relatively straightforward scenarios. In reality, recommendation is often a more complex problem: it is usually just...... a single step in the user's more complex background need. These background needs can often place a variety of constraints on which recommendations are interesting to the user and when they are appropriate. However, relatively little research has been done on these complex recommendation scenarios....... The ComplexRec 2017 workshop addressed this by providing an interactive venue for discussing approaches to recommendation in complex scenarios that have no simple one-size-fits-all-solution....

ThP05 Biogeneration of Volatile Selenium Compounds in Biosolids/Biofuels and Quantification by VD/GC/ICPMS

Science.gov (United States)

A noval analytical approach that uses VD/GC/ICPMS for the on-line extraction and quantificationof volatile organopmetalloids is described. Several species of arsenic, selenium, antimony, bismuth and tellurium are amenable to this technique. Preliminary results of a study on the...

Principles for prevention of toxic effects from metals

DEFF Research Database (Denmark)

Landrigan, Philip J.; Kotelchuk, David; Grandjean, Philippe

2007-01-01

of the Toxic Effects of Metals Aluminum Antimony Arsenic Barium Beryllium Bismuth Cadmium Chromium Cobalt Copper Gallium and Semiconductor Compounds Germanium Indium Iron Lead Manganese Mercury Molybdenum Nickel Palladium Platinum Selenium Silver Tellurium Thallium Tin Titanium Tungsten Uranium Vanadium Zinc...

77 FR 47030 - Seamless Refined Copper Pipe and Tube From the People's Republic of China: Preliminary Results of...

Science.gov (United States)

2012-08-07

... 0.8 Te--Tellurium 0.8 Zn--Zinc 1.0 Zr--Zirconium 0.3 Other elements (each) 0.3 Excluded from the... and sells a small amount of copper slag and copper ash; therefore, the Department has granted a by...

Seasonal study on Bothriocephalus as indicator of metal pollution in ...

African Journals Online (AJOL)

... vanadium, chromium, manganese, iron, cobalt, nickel, copper, zinc, arsenic, selenium, molybdenum, cadmium, tin, antimony, tellurium, barium, mercury, thallium, lead and uranium) were determined with an ICP-MS. Bioconcentration of metals (selenium, mercury, and lead during autumn; copper, zinc, selenium, cadmium, ...

Effect of gamma radiation on optical and electrical properties of ...

Indian Academy of Sciences (India)

Wintec

Tellurium dioxide; thin films; optical bandgap; gamma radiation dose; dosimeter. 1. Introduction. It is now ... material to ionizing radiations (such as X-rays, gamma rays, beta ..... Mag. 19 19. Mott N F and Davis E 1979 Electronic process in non-.

Dynamic complexity: plant receptor complexes at the plasma membrane.

Science.gov (United States)

Burkart, Rebecca C; Stahl, Yvonne

2017-12-01

Plant receptor complexes at the cell surface perceive many different external and internal signalling molecules and relay these signals into the cell to regulate development, growth and immunity. Recent progress in the analyses of receptor complexes using different live cell imaging approaches have shown that receptor complex formation and composition are dynamic and take place at specific microdomains at the plasma membrane. In this review we focus on three prominent examples of Arabidopsis thaliana receptor complexes and how their dynamic spatio-temporal distribution at the PM has been studied recently. We will elaborate on the newly emerging concept of plasma membrane microdomains as potential hubs for specific receptor complex assembly and signalling outputs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Revitalizing Complex Analysis: A Transition-to-Proof Course Centered on Complex Topics

Science.gov (United States)

Sachs, Robert

2017-01-01

A new transition course centered on complex topics would help in revitalizing complex analysis in two ways: first, provide early exposure to complex functions, sparking greater interest in the complex analysis course; second, create extra time in the complex analysis course by eliminating the "complex precalculus" part of the course. In…

3D complex: a structural classification of protein complexes.

Directory of Open Access Journals (Sweden)

Emmanuel D Levy

2006-11-01

Full Text Available Most of the proteins in a cell assemble into complexes to carry out their function. It is therefore crucial to understand the physicochemical properties as well as the evolution of interactions between proteins. The Protein Data Bank represents an important source of information for such studies, because more than half of the structures are homo- or heteromeric protein complexes. Here we propose the first hierarchical classification of whole protein complexes of known 3-D structure, based on representing their fundamental structural features as a graph. This classification provides the first overview of all the complexes in the Protein Data Bank and allows nonredundant sets to be derived at different levels of detail. This reveals that between one-half and two-thirds of known structures are multimeric, depending on the level of redundancy accepted. We also analyse the structures in terms of the topological arrangement of their subunits and find that they form a small number of arrangements compared with all theoretically possible ones. This is because most complexes contain four subunits or less, and the large majority are homomeric. In addition, there is a strong tendency for symmetry in complexes, even for heteromeric complexes. Finally, through comparison of Biological Units in the Protein Data Bank with the Protein Quaternary Structure database, we identified many possible errors in quaternary structure assignments. Our classification, available as a database and Web server at http://www.3Dcomplex.org, will be a starting point for future work aimed at understanding the structure and evolution of protein complexes.

Unraveling chaotic attractors by complex networks and measurements of stock market complexity

International Nuclear Information System (INIS)

Cao, Hongduo; Li, Ying

2014-01-01

We present a novel method for measuring the complexity of a time series by unraveling a chaotic attractor modeled on complex networks. The complexity index R, which can potentially be exploited for prediction, has a similar meaning to the Kolmogorov complexity (calculated from the Lempel–Ziv complexity), and is an appropriate measure of a series' complexity. The proposed method is used to research the complexity of the world's major capital markets. None of these markets are completely random, and they have different degrees of complexity, both over the entire length of their time series and at a level of detail. However, developing markets differ significantly from mature markets. Specifically, the complexity of mature stock markets is stronger and more stable over time, whereas developing markets exhibit relatively low and unstable complexity over certain time periods, implying a stronger long-term price memory process

Unraveling chaotic attractors by complex networks and measurements of stock market complexity.

Science.gov (United States)

Cao, Hongduo; Li, Ying

2014-03-01

We present a novel method for measuring the complexity of a time series by unraveling a chaotic attractor modeled on complex networks. The complexity index R, which can potentially be exploited for prediction, has a similar meaning to the Kolmogorov complexity (calculated from the Lempel-Ziv complexity), and is an appropriate measure of a series' complexity. The proposed method is used to research the complexity of the world's major capital markets. None of these markets are completely random, and they have different degrees of complexity, both over the entire length of their time series and at a level of detail. However, developing markets differ significantly from mature markets. Specifically, the complexity of mature stock markets is stronger and more stable over time, whereas developing markets exhibit relatively low and unstable complexity over certain time periods, implying a stronger long-term price memory process.

Tetrabromido[4-(triphenylphosphanyloxybutyl]tellurium acetonitrile monosolvate

Directory of Open Access Journals (Sweden)

Sari M. Närhi

2013-02-01

Full Text Available In the title compound, [TeBr4(C22H23OP]·CH3CN, the Te atom exhibits a square-pyramidal coordination with an apical Te—C bond and four basal Te—Br bonds. The conformation of the aliphatic C—C—C—C chain is gauche [torsion angle = −67.7 (8°]. A weak C—H...Br interaction helps to establish the conformation. In the crystal, there is a weak secondary bonding interaction [Te...N = 3.456 (11 Å] between the Te atom and the N atom of the solvent molecule, which completes a distorted TeNCBr4 octahedron. Inversion dimers linked by pairs of C—H...Br interactions are also observed.

Tellurium purification: various techniques and limitations

Indian Academy of Sciences (India)

Unknown

-chemical techniques such as vacuum distillation and zone refining are discussed. It was found that the clean environments, design, handling and cleaning of quartz ware are equally important in achieving the desired purity levels. Keywords.

Characterising refractive index dispersion in chalcogenide glasses

DEFF Research Database (Denmark)

Fang, Y.; Sojka, L.; Jayasuriya, D.

2016-01-01

Much effort has been devoted to the study of glasses that contain the chalcogen elements (sulfur, selenium and tellurium) for photonics' applications out to MIR wavelengths. In this paper we describe some techniques for determining the refractive index dispersion characteristics of these glasses...

Zn2(TeO3Br2

Directory of Open Access Journals (Sweden)

Mats Johnsson

2008-05-01

Full Text Available Single crystals of dizinc tellurium dibromide trioxide, Zn2(TeO3Br2, were synthesized via a transport reaction in sealed evacuated silica tubes. The compound has a layered crystal structure in which the building units are [ZnO4Br] distorted square pyramids, [ZnO2Br2] distorted tetrahedra, and [TeO3E] tetrahedra (E being the 5s2 lone pair of Te4+ joined through sharing of edges and corners to form layers of no net charge. Bromine atoms and tellurium lone pairs protrude from the surfaces of each layer towards adjacent layers. This new compound Zn2(TeO3Br2 is isostructural with the synthetic compounds Zn2(TeO3Cl2, CuZn(TeO32, Co2(TeO3Br2 and the mineral sophiite, Zn2(SeO3Cl2.

Charge transport properties of CdMnTe radiation detectors

Directory of Open Access Journals (Sweden)

Prokopovich D. A.

2012-10-01

Full Text Available Growth, fabrication and characterization of indium-doped cadmium manganese telluride (CdMnTe radiation detectors have been described. Alpha-particle spectroscopy measurements and time resolved current transient measurements have yielded an average charge collection efficiency approaching 100 %. Spatially resolved charge collection efficiency maps have been produced for a range of detector bias voltages. Inhomogeneities in the charge transport of the CdMnTe crystals have been associated with chains of tellurium inclusions within the detector bulk. Further, it has been shown that the role of tellurium inclusions in degrading charge collection is reduced with increasing values of bias voltage. The electron drift velocity was calculated from the rise time distribution of the preamplifier output pulses at each measured bias. From the dependence of drift velocity on applied electric field the electron mobility was found to be μn = (718 ± 55 cm2/Vs at room temperature.

Electrochemical Deposition of Lanthanum Telluride Thin Films and Nanowires

Science.gov (United States)

Chi, Su (Ike); Farias, Stephen; Cammarata, Robert

2013-03-01

Tellurium alloys are characterized by their high performance thermoelectric properties and recent research has shown nanostructured tellurium alloys display even greater performance than bulk equivalents. Increased thermoelectric efficiency of nanostructured materials have led to significant interests in developing thin film and nanowire structures. Here, we report on the first successful electrodeposition of lanthanum telluride thin films and nanowires. The electrodeposition of lanthanum telluride thin films is performed in ionic liquids at room temperature. The synthesis of nanowires involves electrodepositing lanthanum telluride arrays into anodic aluminum oxide (AAO) nanoporous membranes. These novel procedures can serve as an alternative means of simple, inexpensive and laboratory-environment friendly methods to synthesize nanostructured thermoelectric materials. The thermoelectric properties of thin films and nanowires will be presented to compare to current state-of-the-art thermoelectric materials. The morphologies and chemical compositions of the deposited films and nanowires are characterized using SEM and EDAX analysis.

Complex Correspondence Principle

International Nuclear Information System (INIS)

Bender, Carl M.; Meisinger, Peter N.; Hook, Daniel W.; Wang Qinghai

2010-01-01

Quantum mechanics and classical mechanics are distinctly different theories, but the correspondence principle states that quantum particles behave classically in the limit of high quantum number. In recent years much research has been done on extending both quantum and classical mechanics into the complex domain. These complex extensions continue to exhibit a correspondence, and this correspondence becomes more pronounced in the complex domain. The association between complex quantum mechanics and complex classical mechanics is subtle and demonstrating this relationship requires the use of asymptotics beyond all orders.

Uranium thiolate complexes

International Nuclear Information System (INIS)

Leverd, Pascal C.

1994-01-01

This research thesis proposes a new approach to the chemistry of uranium thiolate complexes as these compounds are very promising for various uses (in bio-inorganic chemistry, in some industrial processes like oil desulphurization). It more particularly addresses the U-S bond or more generally bonds between polarizable materials and hard metals. The author thus reports the study of uranium organometallic thiolates (tricyclo-penta-dienic and mono-cyclo-octa-tetraenylic complexes), and of uranium homoleptic thiolates (tetra-thiolate complexes, hexa-thiolate complexes, reactivity of homoleptic thiolate complexes) [fr

Clinical Complexity in Medicine: A Measurement Model of Task and Patient Complexity.

Science.gov (United States)

Islam, R; Weir, C; Del Fiol, G

2016-01-01

Complexity in medicine needs to be reduced to simple components in a way that is comprehensible to researchers and clinicians. Few studies in the current literature propose a measurement model that addresses both task and patient complexity in medicine. The objective of this paper is to develop an integrated approach to understand and measure clinical complexity by incorporating both task and patient complexity components focusing on the infectious disease domain. The measurement model was adapted and modified for the healthcare domain. Three clinical infectious disease teams were observed, audio-recorded and transcribed. Each team included an infectious diseases expert, one infectious diseases fellow, one physician assistant and one pharmacy resident fellow. The transcripts were parsed and the authors independently coded complexity attributes. This baseline measurement model of clinical complexity was modified in an initial set of coding processes and further validated in a consensus-based iterative process that included several meetings and email discussions by three clinical experts from diverse backgrounds from the Department of Biomedical Informatics at the University of Utah. Inter-rater reliability was calculated using Cohen's kappa. The proposed clinical complexity model consists of two separate components. The first is a clinical task complexity model with 13 clinical complexity-contributing factors and 7 dimensions. The second is the patient complexity model with 11 complexity-contributing factors and 5 dimensions. The measurement model for complexity encompassing both task and patient complexity will be a valuable resource for future researchers and industry to measure and understand complexity in healthcare.

Improvement of the obtention process of {sup 131} I of ININ through studies of equipment design and process parameters fitting in the simulator; Perfeccionamiento del proceso de obtencion del {sup 131} I del ININ mediante estudios de diseno del equipo y ajustes de parametros del proceso en el simulador

Energy Technology Data Exchange (ETDEWEB)

Zepeda M, M C

2006-07-01

The main objective of the work was to achieve a high yield of the reaction that happens among the vapors of {sup 131} I and the NaOH to obtain sodium iodide (Na{sup 131} I) in solution optimizing the contact time of the molecules in gaseous state of {sup 131} I with the NaOH molecules through the bubbling velocity of the {sup 131} I in the solution of NaOH 0.1 N, as well as the operation temperature during the distillation process by dry via starting from tellurium dioxide (TeO{sub 2}) with the purpose of that the {sup 131} I that is obtained in the form of Na{sup 131} I solution presents the necessary quality that allows to distribute it in the market. The particular objectives were: a) To improve the distillation equipment used for the obtaining of {sup 131} I starting from irradiated tellurium dioxide redrawing the dilution system with the purpose of recovering the {sup 131} I in a minimum volume of sodium hydroxide (NaOH). b) To achieve a bigger time of contact among the molecules of {sup 131} I in gaseous state with the molecules of NaOH in solution through the bubbling velocity and of the redrawing of the dilution system. c) To implement the production of {sup 131} I by dry distillation via starting from tellurium dioxide, obtaining it with a high radionuclide and radiochemical purity. d) To obtain {sup 131} I with the necessary specifications that it marks the pharmacopoeia and it can be used with medical ends. (Author)

Improvement of the obtention process of 131 I of ININ through studies of equipment design and process parameters fitting in the simulator

International Nuclear Information System (INIS)

Zepeda M, M.C.

2006-01-01

The main objective of the work was to achieve a high yield of the reaction that happens among the vapors of 131 I and the NaOH to obtain sodium iodide (Na 131 I) in solution optimizing the contact time of the molecules in gaseous state of 131 I with the NaOH molecules through the bubbling velocity of the 131 I in the solution of NaOH 0.1 N, as well as the operation temperature during the distillation process by dry via starting from tellurium dioxide (TeO 2 ) with the purpose of that the 131 I that is obtained in the form of Na 131 I solution presents the necessary quality that allows to distribute it in the market. The particular objectives were: a) To improve the distillation equipment used for the obtaining of 131 I starting from irradiated tellurium dioxide redrawing the dilution system with the purpose of recovering the 131 I in a minimum volume of sodium hydroxide (NaOH). b) To achieve a bigger time of contact among the molecules of 131 I in gaseous state with the molecules of NaOH in solution through the bubbling velocity and of the redrawing of the dilution system. c) To implement the production of 131 I by dry distillation via starting from tellurium dioxide, obtaining it with a high radionuclide and radiochemical purity. d) To obtain 131 I with the necessary specifications that it marks the pharmacopoeia and it can be used with medical ends. (Author)

Organoselenium compounds prevent hyperphosphorylation of cytoskeletal proteins induced by the neurotoxic agent diphenyl ditelluride in cerebral cortex of young rats

International Nuclear Information System (INIS)

Moretto, M.B.; Funchal, C.; Zeni, G.; Rocha, J.B.T.; Pessoa-Pureur, R.

2005-01-01

In this work we investigated the protective ability of the selenium compounds ebselen and diphenyl diselenide against the effect of diphenyl ditelluride on the in vitro incorporation of 32 P into intermediate filament (IF) proteins from slices of cerebral cortex of 17-day-old rats. We observed that ditelluride in the concentrations of 1, 15 and 50 μM induced hyperphosphorylation of the high-salt Triton insoluble neurofilament subunits (NF-M and NF-L), glial fibrillary acidic protein (GFAP) and vimentin, without altering the immunocontent of these proteins. Concerning the selenium compounds, diselenide (1, 15 and 50 μM) did not induce alteration of the in vitro phosphorylation of the IF proteins. Otherwise, ebselen induced an altered in vitro phosphorylation of the cytoskeletal proteins in a dose-dependent manner. At intermediate concentrations (15 and 30 μM) it increased the in vitro phosphorylation even though, at low (5 μM) or high (50 and 100 μM) concentrations this compound was ineffective in altering the activity of the cytoskeletal-associated phosphorylating system. In addition, 15 μM diselenide and 5 μM ebselen, presented a protective effect against the action of ditelluride, on the phosphorylation of the proteins studied. Considering that hyperphosphorylation of cytoskeletal proteins is associated with neuronal dysfunction and neurodegeneration, it is probable that the effects of ditelluride could be related to the remarkable neurotoxicity of this organic form of tellurium. Furthermore the neuroprotective action of selenium compounds against tellurium effects could be a promising route to be exploited for a possible treatment of organic tellurium poisoning

Thinking Forbidden Thoughts: The Oedipus Complex as a Complex of Knowing.

Science.gov (United States)

Schein, Michael

2016-04-01

The Oedipus complex, considered by Freud the "nuclear complex of development," played a central role in the evolution of psychoanalytic thought. This paper returns to the point of transition from the seduction theory, Freud's initial theorem, to the oedipal model, and suggests that the Oedipus complex is first and foremost a text and as such contains a multiplicity of narratives. In particular, the author articulates the close relation between the Oedipus complex and the subject of knowing, postulating that underlying its surface level, the deep-level structure of this complex is one of knowing. As a complex of knowing it is of dual quality, both promoting and impeding the ability to know.

Complexity-management in SME : organization of complex relationships

NARCIS (Netherlands)

Gregus, M.; Mandorf, S.

2009-01-01

The complexity of companies' environment IS growmg. Complexity management and restructuring of small and medium-sized enterprises (SME) become big challenges of business studies in the next future. A chance could be seen in the use of e-business strategies and the implementation of information

Pramana – Journal of Physics | Indian Academy of Sciences

Indian Academy of Sciences (India)

Electronic switching in amorphous chalcogenide semiconductors has been observed and studied for nearly forty years. Technological exploitation of this phenomenon has most recently emerged in DVD's where GST, a compound of germanium, antimony, and tellurium, is used to store information. We explain how GST ...

Crystallography of the Sb-Te-Ni system

Czech Academy of Sciences Publication Activity Database

Laufek, F.; Drábek, M.; Skála, Roman; Císařová, I.

2005-01-01

Roč. 12, č. 2 (2005), s. 153-154 ISSN 1211-5894 Grant - others:GAUK(CZ) 43-203391 Institutional research plan: CEZ:AV0Z30130516 Keywords : crystallography * antimony * tellurium Subject RIV: DB - Geology ; Mineralogy http:// xray .cz/ms/bul2005-2/student3.pdf

Managing Complexity

DEFF Research Database (Denmark)

Maylath, Bruce; Vandepitte, Sonia; Minacori, Patricia

2013-01-01

and into French. The complexity of the undertaking proved to be a central element in the students' learning, as the collaboration closely resembles the complexity of international documentation workplaces of language service providers. © Association of Teachers of Technical Writing.......This article discusses the largest and most complex international learning-by-doing project to date- a project involving translation from Danish and Dutch into English and editing into American English alongside a project involving writing, usability testing, and translation from English into Dutch...

Mathematics for electric engineers. Complex numbers; Mathematiques pour l`electricien. Nombres complexes

Energy Technology Data Exchange (ETDEWEB)

Rouxel, C. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

1999-05-01

Complex numbers are widely used in electrical engineering. This article is divided into 5 parts dealing successively with: the cartesian form of complex numbers (definition, conjugated complex numbers, graphical representation); the trigonometrical form of complex numbers (module and argument, trigonometrical form, exponential notation, multiplication and division of two complex numbers); Moivre and Euler formulae; applications (square root and second degree equation, n. roots, plan rotation and similarity); cissoidal transformation (definition, properties, applications to electricity: complex impedance in permanent sinusoidal regime, transfer function of a linear system in permanent regime, study of an example). (J.S.)

ComplexRec 2017

DEFF Research Database (Denmark)

a single step in the user's more complex background need. These background needs can often place a variety of constraints on which recommendations are interesting to the user and when they are appropriate. However, relatively little research has been done on these complex recommendation scenarios....... The ComplexRec 2017 workshop addressed this by providing an interactive venue for discussing approaches to recommendation in complex scenarios that have no simple one-size-fits-all-solution....

Complex variables

CERN Document Server

Fisher, Stephen D

1999-01-01

The most important topics in the theory and application of complex variables receive a thorough, coherent treatment in this introductory text. Intended for undergraduates or graduate students in science, mathematics, and engineering, this volume features hundreds of solved examples, exercises, and applications designed to foster a complete understanding of complex variables as well as an appreciation of their mathematical beauty and elegance. Prerequisites are minimal; a three-semester course in calculus will suffice to prepare students for discussions of these topics: the complex plane, basic

Complexity Management In Projects Between Rational Momentum And Complex Conditions

DEFF Research Database (Denmark)

Mac, Anita; Schlamovitz, Jesper

2015-01-01

Abstract: This study takes its departure in a model of complexity, developed by Stacey (1993), to test and discuss its practical benefit as perceived by practicing project managers. Based on a survey, the study finds that complexity is a phenomenon recognized by project managers, and complexity...... management is associated with benefits in the development of tasks and managing stakeholders. It is also associated with some difficulty in terms of an increased need for dialogue and a risk of creating goal ambiguity. Based on the findings, we conclude that classical project management approaches can...... benefit from incorporating complexity management....

Complexity management in projects between rational momentum and complex conditions

DEFF Research Database (Denmark)

Mac, Anita; Schlamovitz, Jesper

This study takes its departure in a model of complexity, developed by Stacey (1993), to test and discuss its practical benefit as perceived by practicing project managers. Based on a survey, the study finds that complexity is a phenomenon recognized by project managers, and complexity management...... is associated with benefits in the development of tasks and managing stakeholders. It is also associated with some difficulty in terms of an increased need for dialogue and a risk of creating goal ambiguity. Based on the findings, we conclude that classical project management approaches can benefit from...... incorporating complexity management....

Solidification of highly active wastes

International Nuclear Information System (INIS)

Morris, J.B.

1984-11-01

Final reports are presented on work on the following topics: glass technology; enhancement of off-gas aerosol collection; formation and trapping of volatile ruthenium; volatilisation of caesium, technetium and tellurium in high-level waste vitrification; deposition of ruthenium; and calcination of high-level waste liquors. (author)

Celebrating Two Centuries of Research in Selenium Chemistry: State of the Art and New Prospective

Directory of Open Access Journals (Sweden)

Claudio Santi

2017-12-01

Full Text Available In 2017, the 200th anniversary of the discovery of selenium was celebrated. In 1817, the Swedish chemists, Berzelius and Gahn, on roasting 200 kg of sulfur from a pyrite from the Falun mine, obtained about 3 g of a precipitate that they first wrongly identified as tellurium. Berzelius doubted this result and repeated the analysis some months later realizing that a new element was in his hands and he named this element Selenium (Greek: Selene, moon in consideration of its resemblance to Tellurium (Latin: Tellus, earth. Several events were organized in the year for this special celebration and this Special Issue would like to be an additional contribution to the success of a research that, especially during the last decades, rapidly grew in different fields: synthesis, medicinal chemistry, biology, material, and environment. These studies are strongly characterized by multi- and interdisciplinary connections, and, for this reason, we collected here contributions coming from different areas and disciplines, not exclusively synthetic organic chemistry.

Chemical interaction between (Cs-Te) doped fuels and cladding material under irradiation

International Nuclear Information System (INIS)

Delbrassine, A.; Flipot, A.J.

1977-01-01

Pins containing UO 2 -30 wt.% PuO 2 low density pellets and or caesium and or tellurium as doping elements have been irradiated for about 40 days in the BR 2 reactor. The effect of two Cs/Te ratios, namely 1.3 and 4, and a wide range of O/M ratios on the inner corrosion of the clad has been investigated. The influence of tellurium on the attack of the cladding has been pointed out. It may be responsible for the chromium and nickel depletion in the grain boundaries of the steal. The corrosion patterns and the thickness of the corroded layer could be different in the total length of a fuel pin. It seems therefore necessary to measure the effective Cs/Te ratio associated with the local corrosion layers. This local Cs/Te ratio should be more useful than the initial mean Cs/Te ratio in a pin for understanding the corrosion phenomena. (author)

Zn2(TeO3)Br2

Science.gov (United States)

Zhang, Dong; Johnsson, Mats

2008-01-01

Single crystals of dizinc tellurium dibromide trioxide, Zn2(TeO3)Br2, were synthesized via a transport reaction in sealed evacuated silica tubes. The compound has a layered crystal structure in which the building units are [ZnO4Br] distorted square pyramids, [ZnO2Br2] distorted tetra­hedra, and [TeO3 E] tetra­hedra (E being the 5s 2 lone pair of Te4+) joined through sharing of edges and corners to form layers of no net charge. Bromine atoms and tellurium lone pairs protrude from the surfaces of each layer towards adjacent layers. This new compound Zn2(TeO3)Br2 is isostructural with the synthetic compounds Zn2(TeO3)Cl2, CuZn(TeO3)2, Co2(TeO3)Br2 and the mineral sophiite, Zn2(SeO3)Cl2. PMID:21202162

Delineation of phase fields at the Te-rich end of the Ru Te binary system

Science.gov (United States)

Ali (Basu), M.; Bharadwaj, S. R.; Das, D.

2005-04-01

The tellurium rich side of the ruthenium-tellurium binary system was studied by differential thermal analysis. To avoid reported problems of Te loss by evaporation and reactive interference of Te to the thermocouples of the thermal analyzer, the present study made use of specially designed sealed quartz capsules as DTA containers. The thermal analyses were carried out over the compositional range of 0.66 ⩽ xTe ⩽ 1.00 with the help of SETARAM TG/DTA and other indigenously built thermal analyzers available in this laboratory. The thermal data generated for fifteen different compositions were interpreted for the nature of phase transitions occurring at their characteristic temperatures. The Ru-Te binary system was found to have a eutectic transformation at 444 °C at a composition of xTe = 0.918 and a monotectic transformation at 447 °C at a composition of xTe = 0.700. Up to 6 at.% Ru is soluble in Te at about 440 °C.

Delineation of phase fields at the Te-rich end of the Ru-Te binary system

International Nuclear Information System (INIS)

Ali, M.; Bharadwaj, S.R.; Das, D.

2005-01-01

The tellurium rich side of the ruthenium-tellurium binary system was studied by differential thermal analysis. To avoid reported problems of Te loss by evaporation and reactive interference of Te to the thermocouples of the thermal analyzer, the present study made use of specially designed sealed quartz capsules as DTA containers. The thermal analyses were carried out over the compositional range of 0.66 x Te 1.00 with the help of SETARAM TG/DTA and other indigenously built thermal analyzers available in this laboratory. The thermal data generated for fifteen different compositions were interpreted for the nature of phase transitions occurring at their characteristic temperatures. The Ru-Te binary system was found to have a eutectic transformation at 444 deg. C at a composition of x Te = 0.918 and a monotectic transformation at 447 deg. C at a composition of x Te = 0.700. Up to 6 at.% Ru is soluble in Te at about 440 deg. C

Discussion on the electrical and thermoelectrical properties of amorphous In-Sb-Te Films

Energy Technology Data Exchange (ETDEWEB)

Aly, K.A. [University of Jeddah, Physics Department, Faculty of Science and Arts, Khulais, Jeddah (Saudi Arabia); Al-Azhar University, Assiut Branch, Physics Department, Faculty of Science, Asyut (Egypt); Saddeek, Y. [Al-Azhar University, Assiut Branch, Physics Department, Faculty of Science, Asyut (Egypt); Dahshan, A. [Port Said University, Department of Physics, Faculty of Science, Port Said (Egypt); King Khalid University, Department of Physics, Faculty of Science for Girls, Abha (Saudi Arabia)

2016-03-15

Different compositions of (In{sub 0.5}Sb{sub 0.5}){sub 1-x}Te{sub x} (0.50 ≤ x ≤ 0.65) thin films were prepared by thermal evaporated technique, onto pre-cleaned glass substrates at ∝298 K. Both dark electrical resistivity (ρ) and thermoelectric power (S) were measured in the temperature range 300-420 K. The concentration of the free carriers is obtained from DC conductivity and thermoelectric power measurements. Seebeck coefficient was found to be positive over entire temperature range, indicating that (In{sub 0.5}Sb{sub 0.5}){sub 1-x}Te{sub x} films are p-type semiconducting materials. Also, the variation of the mobility with temperature has been estimated. Increasing tellurium concentration is found to affect the DC conductivity and thermoelectric power of the studied films. The activation energies obtained from the DC conductivity and thermoelectric power increase with increasing tellurium content. The obtained results were interpreted according to the chemical bond approach. (orig.)

Thermodynamic analysis of the Cu2S-Cu2Te system using dissociation pressure data

International Nuclear Information System (INIS)

Glazov, V.M.; Pashinkin, A.S.; Burkhanov, A.S.; Saleeva, N.M.

1978-01-01

The Knudsen effusive method has been used for studying the dissociation pressure in the Cu 2 S-Cu 2 Te system, and on the basis of the experimental data obtained, the tellurium activity in the system and the mixing energy have been calculated. The dissociation pressure of pure components and alloys containing 10, 30, 50, 70, and 90 mol% of copper telluride within the temperature range of 750-1200 deg C has been studied. A smooth character of the concentration dependence of tellurium activity is observed, which points to the formation of a continuous series of solid solutions in the Cu 2 S-Cu 2 Te system within the temperature range studied. The data on the mixing energy in the system show a good agreement of the values obtained from the dissociation pressure with those determined from the fusibility diagram. The results indicate that the system in question is described well within the framework of the model of regular solutions

Complexity Theory

Science.gov (United States)

Lee, William H K.

2016-01-01

A complex system consists of many interacting parts, generates new collective behavior through self organization, and adaptively evolves through time. Many theories have been developed to study complex systems, including chaos, fractals, cellular automata, self organization, stochastic processes, turbulence, and genetic algorithms.

Synthesis, Processing, and Thermoelectric Properties of Germanium-Antimony-Tellurium Based Compounds and Alloys

Science.gov (United States)

Williams, Jared Brett

Society has become increasingly more aware of the negative impacts which nonrenewable energy sources have on the environment, and therefore the search for new and more efficient means of energy production has become an important research endeavor. Thermoelectric modules possess the unique ability to convert wasted heat into useful electrical energy via solid state processes, which could vastly improve the efficiency of a number of applications. The materials which accomplish this are typically comprised of semiconductors which exhibit high electrical conductivity, Seebeck coefficient, and thermal resistivity. Together these properties give us a gauge for the overall efficiency of the thermal to electrical energy conversion. Phase change materials are a class of materials primarily used for optical data storage in CDs, DVDs, and Blu-Ray discs. Today's state of the art phase change materials are based on alloys of GeTe and Sb2Te3. These materials have also been found to exhibit high thermoelectric efficiencies. These high efficiencies stem from their complex crystal structure and degenerate semiconducting nature. The purpose of this work was to study and engineer the thermoelectric properties of various alloys and compounds which belong to this family of materials. Specifically studied were the compounds Ge4SbTe5 and Ge17Sb2Te20. In each case various synthesis and processing strategies were implemented to increase the thermoelectric performance and better understand the fundamental electrical and thermal properties. Finally various proposals for future work on these materials are presented, all of which are based on the findings described herein.

Phospholyl-uranium complexes

International Nuclear Information System (INIS)

Gradoz, Philippe

1993-01-01

After having reported a bibliographical study on penta-methylcyclopentadienyl uranium complexes, and a description of the synthesis and radioactivity of uranium (III) and (IV) boron hydrides compounds, this research thesis reports the study of mono and bis-tetramethyl-phospholyl uranium complexes comprising chloride, boron hydride, alkyl and alkoxide ligands. The third part reports the comparison of structures, stabilities and reactions of homologue complexes in penta-methylcyclopentadienyl and tetramethyl-phospholyl series. The last part addresses the synthesis of tris-phospholyl uranium (III) and (IV) complexes. [fr

Complex saddle points and the sign problem in complex Langevin simulation

International Nuclear Information System (INIS)

Hayata, Tomoya; Hidaka, Yoshimasa; Tanizaki, Yuya

2016-01-01

We show that complex Langevin simulation converges to a wrong result within the semiclassical analysis, by relating it to the Lefschetz-thimble path integral, when the path-integral weight has different phases among dominant complex saddle points. Equilibrium solution of the complex Langevin equation forms local distributions around complex saddle points. Its ensemble average approximately becomes a direct sum of the average in each local distribution, where relative phases among them are dropped. We propose that by taking these phases into account through reweighting, we can solve the wrong convergence problem. However, this prescription may lead to a recurrence of the sign problem in the complex Langevin method for quantum many-body systems.

Complex and symplectic geometry

CERN Document Server

Medori, Costantino; Tomassini, Adriano

2017-01-01

This book arises from the INdAM Meeting "Complex and Symplectic Geometry", which was held in Cortona in June 2016. Several leading specialists, including young researchers, in the field of complex and symplectic geometry, present the state of the art of their research on topics such as the cohomology of complex manifolds; analytic techniques in Kähler and non-Kähler geometry; almost-complex and symplectic structures; special structures on complex manifolds; and deformations of complex objects. The work is intended for researchers in these areas.

Adaptive generalized combination complex synchronization of uncertain real and complex nonlinear systems

Energy Technology Data Exchange (ETDEWEB)

Wang, Shi-bing, E-mail: wang-shibing@dlut.edu.cn, E-mail: wangxy@dlut.edu.cn [School of Computer and Information Engineering, Fuyang Normal University, Fuyang 236041 (China); Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian 116024 (China); Wang, Xing-yuan, E-mail: wang-shibing@dlut.edu.cn, E-mail: wangxy@dlut.edu.cn [Faculty of Electronic Information and Electrical Engineering, Dalian University of Technology, Dalian 116024 (China); Wang, Xiu-you [School of Computer and Information Engineering, Fuyang Normal University, Fuyang 236041 (China); Zhou, Yu-fei [College of Electrical Engineering and Automation, Anhui University, Hefei 230601 (China)

2016-04-15

With comprehensive consideration of generalized synchronization, combination synchronization and adaptive control, this paper investigates a novel adaptive generalized combination complex synchronization (AGCCS) scheme for different real and complex nonlinear systems with unknown parameters. On the basis of Lyapunov stability theory and adaptive control, an AGCCS controller and parameter update laws are derived to achieve synchronization and parameter identification of two real drive systems and a complex response system, as well as two complex drive systems and a real response system. Two simulation examples, namely, ACGCS for chaotic real Lorenz and Chen systems driving a hyperchaotic complex Lü system, and hyperchaotic complex Lorenz and Chen systems driving a real chaotic Lü system, are presented to verify the feasibility and effectiveness of the proposed scheme.

A new generative complexity science of learning for a complex pedagogy

NARCIS (Netherlands)

Jörg, T.

2007-01-01

Proposal for the SIG Chaos and Complexity Theories at AERA 2007 Title: A New Generative Complexity Science of Learning for a Complex Pedagogy Ton Jörg IVLOS Institute of Education University of Utrecht The Netherlands A.G.D.Jorg@ivlos.uu.nl Introduction My paper focuses on the link between thinking

Study of the effect of doping on the temperature stability of the optical properties of germanium single crystals

Energy Technology Data Exchange (ETDEWEB)

Podkopaev, O. I. [Joint-Stock Company “Germanium” (Russian Federation); Shimanskiy, A. F., E-mail: shimanaf@mail.ru [Siberian Federal University (Russian Federation); Kopytkova, S. A.; Filatov, R. A. [Joint-Stock Company “Germanium” (Russian Federation); Golubovskaya, N. O. [Siberian Federal University (Russian Federation)

2016-10-15

The effect of doping on the optical transmittance of germanium single crystals is studied by infrared Fourier spectroscopy. It is established that the introduction of silicon and tellurium additives into germanium doped with antimony provides a means for improving the temperature stability of the optical properties of the crystals.

Bioreduction of selenite and tellurite by Phanerochaete chrysosporium

NARCIS (Netherlands)

Espinosa‐Ortiz, E.J.

2015-01-01

Selenium (Se) and tellurium (Te) are elements, they are part of the chalcogens (VI‐A group of the periodic table) and share common properties. These metalloids are of commercial interest due to their physicochemical properties, and they have been used in a broad range of applications in advanced

Consequences of severe radioactive releases to Nordic Marine environment

DEFF Research Database (Denmark)

Iosjpe, M.; Isaksson, M.; Joensen, H.P.

- or minor – radioactive releases to Nordic marine environment. As a reference, the release amounts from a 3000 MWth reactor size were used. Based on source term analyses, the chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0...

Doping assessment in GaAs nanowires

DEFF Research Database (Denmark)

Goktas, N. Isik; Fiordaliso, Elisabetta Maria; LaPierre, R. R.

2018-01-01

Semiconductor nanowires (NWs) are a candidate technology for future optoelectronic devices. One of the critical issues in NWs is the control of impurity doping for the formation of p-n junctions. In this study, beryllium (p-type dopant) and tellurium (n-type dopant) in self-assisted GaAs NWs...

Study of the effect of doping on the temperature stability of the optical properties of germanium single crystals

International Nuclear Information System (INIS)

Podkopaev, O. I.; Shimanskiy, A. F.; Kopytkova, S. A.; Filatov, R. A.; Golubovskaya, N. O.

2016-01-01

The effect of doping on the optical transmittance of germanium single crystals is studied by infrared Fourier spectroscopy. It is established that the introduction of silicon and tellurium additives into germanium doped with antimony provides a means for improving the temperature stability of the optical properties of the crystals.

Quantum complex rotation and uniform semiclassical calculations of complex energy eigenvalues

International Nuclear Information System (INIS)

Connor, J.N.L.; Smith, A.D.

1983-01-01

Quantum and semiclassical calculations of complex energy eigenvalues have been carried out for an exponential potential of the form V 0 r 2 exp(-r) and Lennard-Jones (12,6) potential. A straightforward method, based on the complex coordinate rotation technique, is described for the quantum calculation of complex eigenenergies. For singular potentials, the method involves an inward and outward integration of the radial Schroedinger equation, followed by matching of the logarithmic derivatives of the wave functions at an intermediate point. For regular potentials, the method is simpler, as only an inward integration is required. Attention is drawn to the World War II researches of Hartree and co-workers who anticipated later quantum mechanical work on the complex rotation method. Complex eigenenergies are also calculated from a uniform semiclassical three turning point quantization formula, which allows for the proximity of the outer pair of complex turning points. Limiting cases of this formula, which are valid for very narrow or very broad widths, are also used in the calculations. We obtain good agreement between the semiclassical and quantum results. For the Lennard-Jones (12,6) potential, we compare resonance energies and widths from the complex energy definition of a resonance with those obtained from the time delay definition

Complex Constructivism: A Theoretical Model of Complexity and Cognition

Science.gov (United States)

Doolittle, Peter E.

2014-01-01

Education has long been driven by its metaphors for teaching and learning. These metaphors have influenced both educational research and educational practice. Complexity and constructivism are two theories that provide functional and robust metaphors. Complexity provides a metaphor for the structure of myriad phenomena, while constructivism…

Complexity in phonology: The complex consonants of simple CV ...

African Journals Online (AJOL)

The main objective of this article is to investigate the interplay of simplicity and complexity in the phonological structure of Zezuru. The article argues that Zezuru affricates, prenasalised consonants (NCs) and velarised consonants (Cws) are subsegmentally complex segments which function as simple onsets. Treating them ...

The Lepanto Cu–Au deposit, Philippines: A fossil hyperacidic volcanic lake complex

Science.gov (United States)

Berger, Byron R.; Henley, Richard W.; Lowers, Heather; Pribil, Michael

2014-01-01

Hyperacidic lakes and associated solfatara in active volcanoes are the expression of magmatic gas expansion from source to surface. Here we show for the first time, that the vein system that comprises the ~ 2 Ma high-sulfidation, Lepanto copper–gold deposit in the Mankayan district (Philippines) was associated with a contemporary hyperacidic volcanic lake complex—possibly the first such lake recognized in the geological record. A 15–20‰ difference in sulfur isotopic composition between barite and sulfides and sulfosalts in the vent fumarole encrustations supports the interpretation that SO2-rich volcanic gas vented into the base of the lake and marginal to it and ties the mineralization directly to magmatic gas expansion, fracture propagation, and mineralization that occurred through a series of decompression steps within the feeder fracture network. These data confirm that crater lake environments such as Kawah Ijen (Java, Indonesia) provide modern day analogs of the Lepanto and other high sulfidation Cu–Au depositing environments.We also provide extensive analysis of sulfosalt–sulfide reactions during vein formation within the hyperacidic lake complex. Pyrite ±  silica deposited first at high temperature followed by enargite that preserves the vapor–solid diffusion of, for example, antimony, tin, and tellurium into the vapor from the crystallizing solid. Subsolidus, intra-crystalline diffusion continued as temperature declined. Pyrite and enargite are replaced by Fe-tennantite in the lodes which initially has low Sb/(Sb + As) atomic ratios around 13.5% close to the ideal tennantite formula, but evolves to higher ratios as crystallization proceeds. Fumarole encrustation clasts and sulfosalts in the lake sediment are more highly evolved with a larger range of trace element substitutions, including antimony. Substitution of especially Zn, Te, Ag, and Sn into tennantite records metal and semi-metal fractionation between the expanding magmatic

Cobalt(III) complex

Indian Academy of Sciences (India)

Administrator

e, 40 µM complex, 10 hrs after dissolution, f, 40 µM complex, after irradiation dose 15 Gy. and H-atoms result in reduction of Co(III) to Co. (II). 6. It is interesting to see in complex containing multiple ligands what is the fate of electron adduct species formed by electron addition. Reduction to. Co(II) and intramolecular transfer ...

Nuclear weapons complex

International Nuclear Information System (INIS)

Rezendes, V.S.

1991-03-01

In this book, GAO characterizes DOE's January 1991 Nuclear Weapons Complex Reconfiguration Study as a starting point for reaching agreement on solutions to many of the complex's safety and environmental problems. Key decisions still need to be made about the size of the complex, where to relocate plutonium operations, what technologies to use for new tritium production, and what to do with excess plutonium. The total cost for reconfiguring and modernizing the complex is still uncertain, and some management issues remain unresolved. Congress faces a difficult task in making test decisions given the conflicting demands for scarce resources in a time of growing budget deficits and war in the Persian Gulf

Complex Networks

CERN Document Server

Evsukoff, Alexandre; González, Marta

2013-01-01

In the last decade we have seen the emergence of a new inter-disciplinary field focusing on the understanding of networks which are dynamic, large, open, and have a structure sometimes called random-biased. The field of Complex Networks is helping us better understand many complex phenomena such as the spread of  deseases, protein interactions, social relationships, to name but a few. Studies in Complex Networks are gaining attention due to some major scientific breakthroughs proposed by network scientists helping us understand and model interactions contained in large datasets. In fact, if we could point to one event leading to the widespread use of complex network analysis is the availability of online databases. Theories of Random Graphs from Erdös and Rényi from the late 1950s led us to believe that most networks had random characteristics. The work on large online datasets told us otherwise. Starting with the work of Barabási and Albert as well as Watts and Strogatz in the late 1990s, we now know th...

Chalcogen-containing oxazolines in the palladium-catalyzed asymmetric allylic alkylation

Directory of Open Access Journals (Sweden)

Braga Antonio L.

2006-01-01

Full Text Available A comparative study about the ability of chiral chalcogen-containing oxazolines to act as chiral ligands in the palladium-catalyzed allylic alkylation of rac-1,3-diphenyl-2-propenyl acetate with dimethyl malonate is reported. Differences in the catalytic performance are observed with sulfur, selenium and tellurium analogues.

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. Ch Sudheer. Articles written in Bulletin of Materials Science. Volume 25 Issue 6 November 2002 pp 545-547. Tellurium purification: various techniques and limitations · D S Prasad Ch Sudheer N R Munirathnam T L Prakash · More Details Abstract Fulltext PDF. Limitations and ...

Desorption of Te capping layer from ZnTe (100): Auger spectroscopy ...

African Journals Online (AJOL)

... configurations of tellurium Te (c (2x2)) and Te (c (2x1)) are confirmed by scanning tunneling microscopy (STM). Such a study reveals a phase transition from a rich-Te to a poor-Te surface as the annealing temperature increases. Keywords: Zinc Tellure; solar cells; structural properties; optoelectronics; semiconductors.

Luminescent converter of neodymium laser radiation

International Nuclear Information System (INIS)

Ryba-Romanowski, W.; Golab, S.

1992-01-01

The new luminescent converter of neodymium laser radiation has been worked out. Activated inorganic compounds of ytterbium and erbium ions has been used as luminescent agent. The multi-component inorganic glass containing tellurium oxide as well as boron, sodium, magnesium and zinc oxides has been applied as a converter matrix

Electro-spark machining of cadmium antimonide

International Nuclear Information System (INIS)

Ivanovskij, V.N.; Stepakhina, K.A.

1975-01-01

Experimental data on electrical erosion of the semiconductor material (cadmium antimonide) alloyed with tellurium are given. The potentialisies and expediency of using the electric-spark method of cutting cadmium antimonide ingots with the resistivity of 1 ohm is discussed. Cutting has been carried out in distilled water and in the air

Power grid complexity

Energy Technology Data Exchange (ETDEWEB)

Mei, Shengwei; Zhang, Xuemin [Tsinghua Univ., Beijing, BJ (China). Dept. of Electrical Engineering; Cao, Ming [Groningen Univ. (Netherlands). Faculty of Mathematics and Natural Sciences

2011-07-01

''Power Grid Complexity'' introduces the complex system theory known as self-organized criticality (SOC) theory and complex network theory, and their applications to power systems. It studies the network characteristics of power systems, such as their small-world properties, structural vulnerability, decomposition and coordination strategies, and simplification and equivalence methods. The book also establishes four blackout models based on SOC theory through which the SOC of power systems is studied at both the macroscopic and microscopic levels. Additionally, applications of complex system theory in power system planning and emergency management platforms are also discussed in depth. This book can serve as a useful reference for engineers and researchers working with power systems. (orig.)

Coxeter-like complexes

Directory of Open Access Journals (Sweden)

Eric Babson

2004-12-01

Full Text Available Motivated by the Coxeter complex associated to a Coxeter system (W,S, we introduce a simplicial regular cell complex Δ(G,S with a G-action associated to any pair (G,S where G is a group and S is a finite set of generators for G which is minimal with respect to inclusion. We examine the topology of Δ(G,S, and in particular the representations of G on its homology groups. We look closely at the case of the symmetric group S n minimally generated by (not necessarily adjacent transpositions, and their type-selected subcomplexes. These include not only the Coxeter complexes of type A, but also the well-studied chessboard complexes.

Technetium complexation by macrocyclic compounds

International Nuclear Information System (INIS)

Li Fan Yu.

1983-01-01

Research in nuclear medicine are directed towards the labelling of biological molecules, however, sup(99m)Tc does not show sufficient affinity for these molecules. The aim of this study was to evaluate the ability of macrocyclic compounds to bind strongly technetium in order to be used as complexation intermediate. The reducing agents used were a stannous complex and sodium dithionite. Cryptates and polyesters are not good complexing agents. They form two complexes: a 2:1 sandwich complex or 3:2 and a 1:1 complex. Cyclams are good complexing agents for technetium their complexations strength was determined by competition with pyrophosphate, gluconate and DTPA. Using the method of ligand exchange, the oxidation state of technetium in the Tc-cyclam complex was IV or V. They are 1:1 cationic complexes, the complex charge is +1. The biodistribution in rats of labelling solutions containing (cyclam 14 ane N 4 ) C 12 H 25 shows a good urinary excretion without intoxication risks [fr

[Tissue-specific nucleoprotein complexes].

Science.gov (United States)

Riadnova, I Iu; Shataeva, L K; Khavinson, V Kh

2000-01-01

A method of isolation of native nucleorprotein complexes from cattle cerebral cortex, thymus, and liver was developed. Compositions of these complexes were studied by means of gel-chromatography and ion-exchange chromatography. These preparations were shown to consist of several fractions of proteins and their complexes differ by molecular mass and electro-chemical properties. Native nucleoprotein complexes revealed high tissue specific activity, which was not species-specific.

Complex analysis and geometry

CERN Document Server

Silva, Alessandro

1993-01-01

The papers in this wide-ranging collection report on the results of investigations from a number of linked disciplines, including complex algebraic geometry, complex analytic geometry of manifolds and spaces, and complex differential geometry.

On Complex Random Variables

Directory of Open Access Journals (Sweden)

Anwer Khurshid

2012-07-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE In this paper, it is shown that a complex multivariate random variable  is a complex multivariate normal random variable of dimensionality if and only if all nondegenerate complex linear combinations of  have a complex univariate normal distribution. The characteristic function of  has been derived, and simpler forms of some theorems have been given using this characterization theorem without assuming that the variance-covariance matrix of the vector  is Hermitian positive definite. Marginal distributions of  have been given. In addition, a complex multivariate t-distribution has been defined and the density derived. A characterization of the complex multivariate t-distribution is given. A few possible uses of this distribution have been suggested.

Complex Systems: An Introduction

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 14; Issue 9. Complex Systems: An Introduction - Anthropic Principle, Terrestrial Complexity, Complex Materials. V K Wadhawan. General Article Volume 14 Issue 9 September 2009 pp 894-906 ...

Simplicial complexes of graphs

CERN Document Server

Jonsson, Jakob

2008-01-01

A graph complex is a finite family of graphs closed under deletion of edges. Graph complexes show up naturally in many different areas of mathematics, including commutative algebra, geometry, and knot theory. Identifying each graph with its edge set, one may view a graph complex as a simplicial complex and hence interpret it as a geometric object. This volume examines topological properties of graph complexes, focusing on homotopy type and homology. Many of the proofs are based on Robin Forman's discrete version of Morse theory. As a byproduct, this volume also provides a loosely defined toolbox for attacking problems in topological combinatorics via discrete Morse theory. In terms of simplicity and power, arguably the most efficient tool is Forman's divide and conquer approach via decision trees; it is successfully applied to a large number of graph and digraph complexes.

X-ray fluorescence spectroscopic determination of heavy metals and ...

African Journals Online (AJOL)

. Antimony. < 6.1. < 6.1. 52. Te. Tellurium. < 7.1. < 7.1. 53. I. Iodine. < 7.1. < 7.1. 55. Cs. Cesium. < 8.1. < 8.1. 56. Ba. Barium. < 8.1. < 600. 57. La. Lanthanum. < 10. < 10. 58. Ce. Cerium. < 12. < 12. 80. Hg. Mercury. < 2. < 2. 81. Tl. Thallium. < 2.9.

Composites comprising biologically-synthesized nanomaterials

Science.gov (United States)

Curran, Seamus; Dias, Sampath; Blau, Werner; Wang, Jun; Oremland, Ronald S; Baesman, Shaun

2013-04-30

The present disclosure describes composite materials containing a polymer material and a nanoscale material dispersed in the polymer material. The nanoscale materials may be biologically synthesized, such as tellurium nanorods synthesized by Bacillus selenitireducens. Composite materials of the present disclosure may have optical limiting properties and find use in optical limiting devices.

Actinide cation-cation complexes

International Nuclear Information System (INIS)

Stoyer, N.J.; Seaborg, G.T.

1994-12-01

The +5 oxidation state of U, Np, Pu, and Am is a linear dioxo cation (AnO 2 + ) with a formal charge of +1. These cations form complexes with a variety of other cations, including actinide cations. Other oxidation states of actinides do not form these cation-cation complexes with any cation other than AnO 2 + ; therefore, cation-cation complexes indicate something unique about AnO 2 + cations compared to actinide cations in general. The first cation-cation complex, NpO 2 + ·UO 2 2+ , was reported by Sullivan, Hindman, and Zielen in 1961. Of the four actinides that form AnO 2 + species, the cation-cation complexes of NpO 2 + have been studied most extensively while the other actinides have not. The only PuO 2 + cation-cation complexes that have been studied are with Fe 3+ and Cr 3+ and neither one has had its equilibrium constant measured. Actinides have small molar absorptivities and cation-cation complexes have small equilibrium constants; therefore, to overcome these obstacles a sensitive technique is required. Spectroscopic techniques are used most often to study cation-cation complexes. Laser-Induced Photacoustic Spectroscopy equilibrium constants for the complexes NpO 2 + ·UO 2 2+ , NpO 2 + ·Th 4+ , PuO 2 + ·UO 2 2+ , and PuO 2 + ·Th 4+ at an ionic strength of 6 M using LIPAS are 2.4 ± 0.2, 1.8 ± 0.9, 2.2 ± 1.5, and ∼0.8 M -1

Conducting metal dithiolate complexes

DEFF Research Database (Denmark)

Underhill, A. E.; Ahmad, M. M.; Turner, D. J.

1985-01-01

Further work on the chemical composition of the one-dimensional metallic metal dithiolene complex Li-Pt(mnt) is reported. The electrical conduction and thermopower properties of the nickel and palladium complexes are reported and compared with those of the platinum compound......Further work on the chemical composition of the one-dimensional metallic metal dithiolene complex Li-Pt(mnt) is reported. The electrical conduction and thermopower properties of the nickel and palladium complexes are reported and compared with those of the platinum compound...

Curcumin complexation with cyclodextrins by the autoclave process: Method development and characterization of complex formation.

Science.gov (United States)

Hagbani, Turki Al; Nazzal, Sami

2017-03-30

One approach to enhance curcumin (CUR) aqueous solubility is to use cyclodextrins (CDs) to form inclusion complexes where CUR is encapsulated as a guest molecule within the internal cavity of the water-soluble CD. Several methods have been reported for the complexation of CUR with CDs. Limited information, however, is available on the use of the autoclave process (AU) in complex formation. The aims of this work were therefore to (1) investigate and evaluate the AU cycle as a complex formation method to enhance CUR solubility; (2) compare the efficacy of the AU process with the freeze-drying (FD) and evaporation (EV) processes in complex formation; and (3) confirm CUR stability by characterizing CUR:CD complexes by NMR, Raman spectroscopy, DSC, and XRD. Significant differences were found in the saturation solubility of CUR from its complexes with CD when prepared by the three complexation methods. The AU yielded a complex with expected chemical and physical fingerprints for a CUR:CD inclusion complex that maintained the chemical integrity and stability of CUR and provided the highest solubility of CUR in water. Physical and chemical characterizations of the AU complexes confirmed the encapsulated of CUR inside the CD cavity and the transformation of the crystalline CUR:CD inclusion complex to an amorphous form. It was concluded that the autoclave process with its short processing time could be used as an alternate and efficient methods for drug:CD complexation. Copyright © 2017 Elsevier B.V. All rights reserved.

Complex analysis

CERN Document Server

Freitag, Eberhard

2005-01-01

The guiding principle of this presentation of ``Classical Complex Analysis'' is to proceed as quickly as possible to the central results while using a small number of notions and concepts from other fields. Thus the prerequisites for understanding this book are minimal; only elementary facts of calculus and algebra are required. The first four chapters cover the essential core of complex analysis: - differentiation in C (including elementary facts about conformal mappings) - integration in C (including complex line integrals, Cauchy's Integral Theorem, and the Integral Formulas) - sequences and series of analytic functions, (isolated) singularities, Laurent series, calculus of residues - construction of analytic functions: the gamma function, Weierstrass' Factorization Theorem, Mittag-Leffler Partial Fraction Decomposition, and -as a particular highlight- the Riemann Mapping Theorem, which characterizes the simply connected domains in C. Further topics included are: - the theory of elliptic functions based on...

Complexes and imagination.

Science.gov (United States)

Kast, Verena

2014-11-01

Fantasies as imaginative activities are seen by Jung as expressions of psychic energy. In the various descriptions of active imagination the observation of the inner image and the dialogue with inner figures, if possible, are important. The model of symbol formation, as Jung describes it, can be experienced in doing active imagination. There is a correspondence between Jung's understanding of complexes and our imaginations: complexes develop a fantasy life. Complex episodes are narratives of difficult dysfunctional relationship episodes that have occurred repeatedly and are internalized with episodic memory. This means that the whole complex episode (the image for the child and the image for the aggressor, connected with emotions) is internalized and can get constellated in everyday relationship. Therefore inner dialogues do not necessarily qualify as active imaginations, often they are the expression of complex-episodes, very similar to fruitless soliloquies. If imaginations of this kind are repeated, new symbols and new possibilities of behaviour are not found. On the contrary, old patterns of behaviour and fantasies are perpetuated and become cemented. Imaginations of this kind need an intervention by the analyst. In clinical examples different kinds of imaginations are discussed. © 2014, The Society of Analytical Psychology.

Leading healthcare in complexity.

Science.gov (United States)

Cohn, Jeffrey

2014-12-01

Healthcare institutions and providers are in complexity. Networks of interconnections from relationships and technology create conditions in which interdependencies and non-linear dynamics lead to surprising, unpredictable outcomes. Previous effective approaches to leadership, focusing on top-down bureaucratic methods, are no longer effective. Leading in complexity requires leaders to accept the complexity, create an adaptive space in which innovation and creativity can flourish and then integrate the successful practices that emerge into the formal organizational structure. Several methods for doing adaptive space work will be discussed. Readers will be able to contrast traditional leadership approaches with leading in complexity. They will learn new behaviours that are required of complexity leaders, along with challenges they will face, often from other leaders within the organization.

Analysis and control of complex dynamical systems robust bifurcation, dynamic attractors, and network complexity

CERN Document Server

Imura, Jun-ichi; Ueta, Tetsushi

2015-01-01

This book is the first to report on theoretical breakthroughs on control of complex dynamical systems developed by collaborative researchers in the two fields of dynamical systems theory and control theory. As well, its basic point of view is of three kinds of complexity: bifurcation phenomena subject to model uncertainty, complex behavior including periodic/quasi-periodic orbits as well as chaotic orbits, and network complexity emerging from dynamical interactions between subsystems. Analysis and Control of Complex Dynamical Systems offers a valuable resource for mathematicians, physicists, and biophysicists, as well as for researchers in nonlinear science and control engineering, allowing them to develop a better fundamental understanding of the analysis and control synthesis of such complex systems.

Modified projective synchronization with complex scaling factors of uncertain real chaos and complex chaos

International Nuclear Information System (INIS)

Zhang Fang-Fang; Liu Shu-Tang; Yu Wei-Yong

2013-01-01

To increase the variety and security of communication, we present the definitions of modified projective synchronization with complex scaling factors (CMPS) of real chaotic systems and complex chaotic systems, where complex scaling factors establish a link between real chaos and complex chaos. Considering all situations of unknown parameters and pseudo-gradient condition, we design adaptive CMPS schemes based on the speed-gradient method for the real drive chaotic system and complex response chaotic system and for the complex drive chaotic system and the real response chaotic system, respectively. The convergence factors and dynamical control strength are added to regulate the convergence speed and increase robustness. Numerical simulations verify the feasibility and effectiveness of the presented schemes. (general)

Studies on Cd1Se0.6Te0.4 Thin Films by Spectroscopic and Diffractometer Characterization

Directory of Open Access Journals (Sweden)

Cliff Orori Mosiori

2017-09-01

Full Text Available Cadmium selenide tellurium is a compound containing cadmium, tellurium and selenium elements forming a combined solid. Hall measurements suggest that it is an n-type semiconductor. Related optical studies indicate that is transparent to infra-red radiation. Structural studies clearly show that it has a wurtzite, sphalerite crystalline forms. Cadmium is a toxic heavy metal, and selenium is only toxic in large amounts or doses. By this toxicity, cadmium selenide is a known to be carcinogen to humans; however, this does not stop investigating it for optoelectronic applications. Current research has narrowed down to investigating cadmium selenide when in the form of nanoparticles. Cadmium selenide finds applications has found applications in opto-electronic devices like laser diodes, biomedical imaging, nano-sensing, high-efficiency solar cells and thin-film transistors. By chemical bath deposition, Cd1Se0.6Te0.4 thin films were grown onto glass. Tellurium was gradually introduced as an impurity and its crystalline structure and optical properties were investigated by XRD and UV-VIS spectroscopy. The main Cd1Se0.6Te0.4/glass characteristics were correlated with the conditions of growing and post-growth treatment and it was found out that films were homogeneous films with controllable thickness onto the glass substrate and suitable for n-type “sandwich” heterostructures applications. Comparison of the intensities of equivalent reflexions provided a test for the internal consistency of the measurements. Equivalent reflexions in two specimens differed on average by 1.4 % and 0.6% from the mean measured intensity, attesting to the high internal consistency of measurements from extended-face crystals. By comparison from data obtained from all samples showed their average deviation from the mean to be 0.9 %.

Selenophene transition metal complexes

Energy Technology Data Exchange (ETDEWEB)

White, Carter James [Iowa State Univ., Ames, IA (United States)

1994-07-27

This research shows that selenophene transition metal complexes have a chemistry that is similar to their thiophene analogs. Selenophene coordination has been demonstrated and confirmed by molecular structure in both the η⁵- and the η¹(Se)-coordination modes. The reaction chemistry of selenophene complexes closely resembles that of the analogous thiophene complexes. One major difference, however, is that selenophene is a better donor ligand than thiophene making the selenophene complexes more stable than the corresponding thiophene complexes. The ⁷⁷Se NMR chemical shift values for selenophene complexes fall within distinct regions primarily depending on the coordination mode of the selenophene ligand. In the final paper, the C-H bond activation of η¹(S)-bound thiophenes, η¹(S)-benzothiophene and η¹(Se)-bound selenophenes has been demonstrated. The deprotonation and rearrangement of the η¹(E)-bound ligand to the carbon bound L-yl complex readily occurs in the presence of base. Reprotonation with a strong acid gives a carbene complex that is unreactive towards nucleophilic attack at the carbene carbon and is stable towards exposure to air. The molecular structure of [Cp(NO)(PPh₃)Re(2-benzothioenylcarbene)]O₃SCF₃ was determined and contains a Re-C bond with substantial double bond character. Methyl substitution for the thienylcarbene or selenylcarbene gives a carbene that rearranges thermally to give back the η¹(E)-bound complex. Based on these model reactions, a new mechanism for the H/D exchange of thiophene over the hydrodesulfurization catalyst has been proposed.

Photocytotoxic lanthanide complexes

Indian Academy of Sciences (India)

Among many applications of lanthanides, gadolinium complexes are used as magnetic resonance imaging (MRI) contrast agents in clinical radiology and luminescent lanthanides for bioanalysis, imaging and sensing. The chemistry of photoactive lanthanide complexes showing biological applications is of recent origin.

Thermoelectrode for thermoelectric converter

International Nuclear Information System (INIS)

Bodiul, Pavel; Bondarciuc, Nicolae; Ghitu, Dumitru; Nikolaeva, Albina; Konopko, Leonid; Turcan, Ana

2008-01-01

The invention relates to the electronic engneering and can be used for manufacturing of thermoelectrodes for thermoelectric converters. The thermoelectrode is made of semiconductor anisotropic material in the form of thread in glass insulation. At the same timer, the thread is made of stannum-doped tellurium in the ratio of 0.1...3 at.%.

Annual Technical Report, Materials Research Laboratory July 1, 1979 - June 30, 1980.

Science.gov (United States)

1980-06-30

TeO2 in the glasses contributes to the formation of four-coordinated boron atoms. There is an apparent change in the coordination of tellurium atoms... Glasses , W. M. Risen, Jr., and Chemisorption and Related Surface Interactions, P. J. Estrup. Since many of the research areas are interrelated, cross...8 IInorganic Glasses .................................................................. 24 Introduction

Physical Complexity and Cognitive Evolution

Science.gov (United States)

Jedlicka, Peter

Our intuition tells us that there is a general trend in the evolution of nature, a trend towards greater complexity. However, there are several definitions of complexity and hence it is difficult to argue for or against the validity of this intuition. Christoph Adami has recently introduced a novel measure called physical complexity that assigns low complexity to both ordered and random systems and high complexity to those in between. Physical complexity measures the amount of information that an organism stores in its genome about the environment in which it evolves. The theory of physical complexity predicts that evolution increases the amount of `knowledge' an organism accumulates about its niche. It might be fruitful to generalize Adami's concept of complexity to the entire evolution (including the evolution of man). Physical complexity fits nicely into the philosophical framework of cognitive biology which considers biological evolution as a progressing process of accumulation of knowledge (as a gradual increase of epistemic complexity). According to this paradigm, evolution is a cognitive `ratchet' that pushes the organisms unidirectionally towards higher complexity. Dynamic environment continually creates problems to be solved. To survive in the environment means to solve the problem, and the solution is an embodied knowledge. Cognitive biology (as well as the theory of physical complexity) uses the concepts of information and entropy and views the evolution from both the information-theoretical and thermodynamical perspective. Concerning humans as conscious beings, it seems necessary to postulate an emergence of a new kind of knowledge - a self-aware and self-referential knowledge. Appearence of selfreflection in evolution indicates that the human brain reached a new qualitative level in the epistemic complexity.

Functionalized active-nucleus complex sensor

Science.gov (United States)

Pines, Alexander; Wemmer, David E.; Spence, Megan; Rubin, Seth

2003-11-25

A functionalized active-nucleus complex sensor that selectively associates with one or more target species, and a method for assaying and screening for one or a plurality of target species utilizing one or a plurality of functionalized active-nucleus complexes with at least two of the functionalized active-nucleus complexes having an attraction affinity to different corresponding target species. The functionalized active-nucleus complex has an active-nucleus and a targeting carrier. The method involves functionalizing an active-nucleus, for each functionalized active-nucleus complex, by incorporating the active-nucleus into a macromolucular or molecular complex that is capable of binding one of the target species and then bringing the macromolecular or molecular complexes into contact with the target species and detecting the occurrence of or change in a nuclear magnetic resonance signal from each of the active-nuclei in each of the functionalized active-nucleus complexes.

Complex Neutrosophic Subsemigroups and Ideals

Directory of Open Access Journals (Sweden)

Muhammad Gulistan

2018-01-01

Full Text Available In this article we study the idea of complex neutrosophic subsemigroups. We define the Cartesian product of complex neutrosophic subsemigroups, give some examples and study some of its related results. We also define complex neutrosophic (left, right, interior ideal in semigroup. Furthermore, we introduce the concept of characteristic function of complex neutrosophic sets, direct product of complex neutrosophic sets and study some results prove on its.

Transition Complexity of Incomplete DFAs

Directory of Open Access Journals (Sweden)

Yuan Gao

2010-08-01

Full Text Available In this paper, we consider the transition complexity of regular languages based on the incomplete deterministic finite automata. A number of results on Boolean operations have been obtained. It is shown that the transition complexity results for union and complementation are very different from the state complexity results for the same operations. However, for intersection, the transition complexity result is similar to that of state complexity.

Charged Nanowire-Directed Growth of Amorphous Calcium Carbonate Nanosheets in a Mixed Solvent for Biomimetic Composite Films.

Science.gov (United States)

Liu, Yangyi; Liu, Lei; Chen, Si-Ming; Chang, Fu-Jia; Mao, Li-Bo; Gao, Huai-Ling; Ma, Tao; Yu, Shu-Hong

2018-04-19

Bio-inspired mineralization is an effective way for fabricating complicated inorganic materials, which inspires us to develop new methods to synthesize materials with fascinating properties. In this article, we report that the charged tellurium nanowires (TeNWs) can be used as bio-macromolecule analogues to direct the formation of amorphous calcium carbonate (ACC) nanosheets (ACCNs) in a mixed solvent. The effects of surface charges and the concentration of the TeNWs on the formation of ACCNs have been investigated. Particularly, the produced ACCNs can be functionalized by Fe3O4 nanoparticles to produce magnetic ACC/Fe3O4 hybrid nanosheets, which can be used to construct ACC/Fe3O4 composite films through a self-evaporation process. Moreover, sodium alginate-ACC nanocomposite films with remarkable toughness and good transmittance can also be fabricated by using such ACCNs as nanoscale building blocks. This mineralization approach in a mixed solvent using charged tellurium nanowires as bio-macromolecule analogues provides a new way for the synthesis of ACCNs, which can be used as nanoscale building blocks for fabrication of biomimetic composite films.

Subsumed complexity: abiogenesis as a by-product of complex energy transduction

Science.gov (United States)

Adam, Z. R.; Zubarev, D.; Aono, M.; Cleaves, H. James

2017-11-01

The origins of life bring into stark relief the inadequacy of our current synthesis of thermodynamic, chemical, physical and information theory to predict the conditions under which complex, living states of organic matter can arise. Origins research has traditionally proceeded under an array of implicit or explicit guiding principles in lieu of a universal formalism for abiogenesis. Within the framework of a new guiding principle for prebiotic chemistry called subsumed complexity, organic compounds are viewed as by-products of energy transduction phenomena at different scales (subatomic, atomic, molecular and polymeric) that retain energy in the form of bonds that inhibit energy from reaching the ground state. There is evidence for an emergent level of complexity that is overlooked in most conceptualizations of abiogenesis that arises from populations of compounds formed from atomic energy input. We posit that different forms of energy input can exhibit different degrees of dissipation complexity within an identical chemical medium. By extension, the maximum capacity for organic chemical complexification across molecular and macromolecular scales subsumes, rather than emerges from, the underlying complexity of energy transduction processes that drive their production and modification. This article is part of the themed issue 'Reconceptualizing the origins of life'.

Spectroscopy of plutonium-organic complexes

International Nuclear Information System (INIS)

Richmann, M.K.; Reed, D.T.

1995-01-01

Information on the spectroscopy of plutonium-organic complexes is needed to help establish the speciation of these complexes under environmentally relevant conditions. Laser photoacoustic spectroscopy (LPAS) and absorption spectrometry were used to characterize the Pu(IV)-citrate and Pu(IV)-nitrilotriacetic acid (NTA) complexes at concentrations of 10 -3 --10 -7 M in aqueous solution. Good agreement was observed between the band shape of the LPAS and absorption spectra for the Pu(IV)-NTA complex. Agreement for the Pu(IV)-citrate complex was not quite as good. In both cases, a linear dependence of the LPAS signal on laser power and total concentration of the complexes was noted. This work is part of an ongoing research effort to study key subsurface interactions of plutonium-organic complexes

Complex Networks IX

CERN Document Server

Coronges, Kate; Gonçalves, Bruno; Sinatra, Roberta; Vespignani, Alessandro; Proceedings of the 9th Conference on Complex Networks; CompleNet 2018

2018-01-01

This book aims to bring together researchers and practitioners working across domains and research disciplines to measure, model, and visualize complex networks. It collects the works presented at the 9th International Conference on Complex Networks (CompleNet) 2018 in Boston, MA in March, 2018. With roots in physical, information and social science, the study of complex networks provides a formal set of mathematical methods, computational tools and theories to describe prescribe and predict dynamics and behaviors of complex systems. Despite their diversity, whether the systems are made up of physical, technological, informational, or social networks, they share many common organizing principles and thus can be studied with similar approaches. This book provides a view of the state-of-the-art in this dynamic field and covers topics such as group decision-making, brain and cellular connectivity, network controllability and resiliency, online activism, recommendation systems, and cyber security.

What is complex in the complex world? Niklas Luhmann and the theory of social systems

Directory of Open Access Journals (Sweden)

Clarissa Eckert Baeta Neves

Full Text Available This paper discusses Niklas Luhmann's understanding of complexity, its function in the theory and the different ways of its use. It starts with the paradigmatic change that occurred in the field of general Science, with the rupture of the Newtonian model. In the 20th century, the paradigm of order, symmetry, regularity, regulation of the intellect to things, collapses.Based on new formulations of Physics, Chemistry, etc., a new universe is built on bases radically opposed to those of modern Science.Chaos, the procedural irreversibility, indeterminism, the observer and the complexity are rehabilitated.This new conceptual context served as substratum to Niklas Luhmann's theoretical reflection.With his Theory of Social Systems, he proposes the reduction of the world's complexity.Social systems have the function of reducing complexity because of their difference in relation to the environment.On the other hand, the reduction of complexity also creates its own complexity. Luhmann defines complexity as the moment when it is not possible anymore for each element to relate at any moment with all the others. Complexity forces the selection, what means contingency and risk. Luhmann expands the concept of complexity when he introduces the figure of the observer and the distinction of complexity as a unit of a multiplicity. He also deals with the limit of relations in connection, the time factor, the self-reference of operations and the representation of complexity in the form of sense. To conclude, the paper discusses the complexity in the system of science, the way it reduces internal and external complexity, in accordance in its own operative basis.

Complexity Leadership: A Theoretical Perspective

Science.gov (United States)

Baltaci, Ali; Balci, Ali

2017-01-01

Complex systems are social networks composed of interactive employees interconnected through collaborative, dynamic ties such as shared goals, perspectives and needs. Complex systems are largely based on "the complex system theory". The complex system theory focuses mainly on finding out and developing strategies and behaviours that…

Organotin complexes with phosphines

International Nuclear Information System (INIS)

Passos, B. de F.T.; Jesus Filho, M.F. de; Filgueiras, C.A.L.; Abras, A.

1988-01-01

A series of organotin complexes was prepared involving phosphines bonded to the organotin moiety. The series include derivatives of SnCl x Ph 4-x (where x varied from zero to four with the phosphines Ph 3 P, (Ph 2 P)CH 2 , (Ph 2 P) 2 (CH 2 ) 2 , cis-(Ph 2 P)CH 2 , and CH 3 C(CH 2 PPh 2 ) 3 . A host of new complexes was obtained, showing different stoichiometries, bonding modes, and coordination numbers around the tin atom. These complexes were characterized by several different chemical and physical methods. The 119 Sn Moessbauer parameters varied differently. Whereas isomer shift values did not great variation for each group of complexs with the same organotin parent (SnCl x Ph 4-x ), reflecting a small change in s charge distribution on the Sn atom upon complexation, quadrupole splitting results varied widely, however, when the parent organotin compound was wholly symmetric (SnCl 4 and SnPPh 4 ), the complexes also tended to show quadrupole splitting values approaching zero. (author)

Nuclear weapons complex

International Nuclear Information System (INIS)

Rezendes, V.S.

1992-04-01

In addition to long-standing safety and environmental problems plaguing the nuclear weapons complex, this paper reports that the Department of Energy (DOE) faces a major new challenge-how to reconfigure the weapons complex to meet the nation's defense needs in the 21st century. Key decisions still need to be made about the size of the complex; where, if necessary, to relocate various operations; what technologies to use for new tritium production; and what to do with excess weapons-grade material. The choices confronting DOE and Congress are difficult given the conflicting demands for limited resources

The Orion complex

International Nuclear Information System (INIS)

Goudis, C.

1982-01-01

This work deals with some of the most typical complexes of interstellar matter and presents a holistic view of the well studied complexes in Orion, built on information derived from various branches of modern astrophysics. A wealth of published data is presented in the form of photographs, contour maps, diagrams and numerous heavily annotated tables. Chapter 1, which is concerned with the large scale view of the Orion region, outlines the morphology of the area and examines in particular the nature of Barnard's Loop and the associated filamentary structure in addition to the origin of the I Orion OB association. Chapter 2 focuses on the Great Orion Nebula (M42 or NGC 1976) and the small H II region to the north (M43 or NGC 1982). Chapter 3 examines the Orion Complex as a whole, i.e. the H II regions M42 and M43, the associated molecular clouds OMC 1 and OMC 2 and their interrelations. Chapter 4 contains a discussion of the empirical models introduced to attempt to explain certain aspects of this very complex region, and chapter 5 investigates the second prominent H II region and molecular cloud complex, NGC 2024 (Orion B, W12). (Auth.)

Algorithmic Relative Complexity

Directory of Open Access Journals (Sweden)

Daniele Cerra

2011-04-01

Full Text Available Information content and compression are tightly related concepts that can be addressed through both classical and algorithmic information theories, on the basis of Shannon entropy and Kolmogorov complexity, respectively. The definition of several entities in Kolmogorov’s framework relies upon ideas from classical information theory, and these two approaches share many common traits. In this work, we expand the relations between these two frameworks by introducing algorithmic cross-complexity and relative complexity, counterparts of the cross-entropy and relative entropy (or Kullback-Leibler divergence found in Shannon’s framework. We define the cross-complexity of an object x with respect to another object y as the amount of computational resources needed to specify x in terms of y, and the complexity of x related to y as the compression power which is lost when adopting such a description for x, compared to the shortest representation of x. Properties of analogous quantities in classical information theory hold for these new concepts. As these notions are incomputable, a suitable approximation based upon data compression is derived to enable the application to real data, yielding a divergence measure applicable to any pair of strings. Example applications are outlined, involving authorship attribution and satellite image classification, as well as a comparison to similar established techniques.

Embracing uncertainty, managing complexity: applying complexity thinking principles to transformation efforts in healthcare systems.

Science.gov (United States)

Khan, Sobia; Vandermorris, Ashley; Shepherd, John; Begun, James W; Lanham, Holly Jordan; Uhl-Bien, Mary; Berta, Whitney

2018-03-21

Complexity thinking is increasingly being embraced in healthcare, which is often described as a complex adaptive system (CAS). Applying CAS to healthcare as an explanatory model for understanding the nature of the system, and to stimulate changes and transformations within the system, is valuable. A seminar series on systems and complexity thinking hosted at the University of Toronto in 2016 offered a number of insights on applications of CAS perspectives to healthcare that we explore here. We synthesized topics from this series into a set of six insights on how complexity thinking fosters a deeper understanding of accepted ideas in healthcare, applications of CAS to actors within the system, and paradoxes in applications of complexity thinking that may require further debate: 1) a complexity lens helps us better understand the nebulous term "context"; 2) concepts of CAS may be applied differently when actors are cognizant of the system in which they operate; 3) actor responses to uncertainty within a CAS is a mechanism for emergent and intentional adaptation; 4) acknowledging complexity supports patient-centred intersectional approaches to patient care; 5) complexity perspectives can support ways that leaders manage change (and transformation) in healthcare; and 6) complexity demands different ways of implementing ideas and assessing the system. To enhance our exploration of key insights, we augmented the knowledge gleaned from the series with key articles on complexity in the literature. Ultimately, complexity thinking acknowledges the "messiness" that we seek to control in healthcare and encourages us to embrace it. This means seeing challenges as opportunities for adaptation, stimulating innovative solutions to ensure positive adaptation, leveraging the social system to enable ideas to emerge and spread across the system, and even more important, acknowledging that these adaptive actions are part of system behaviour just as much as periods of stability are. By

Complexity in practice: understanding primary care as a complex adaptive system

Directory of Open Access Journals (Sweden)

Beverley Ellis

2010-06-01

Conclusions The results are real-world exemplars of the emergent properties of complex adaptive systems. Improving clinical governance in primary care requires both complex social interactions and underpinning informatics. The socio-technical lessons learned from this research should inform future management approaches.

Shapes of interacting RNA complexes

DEFF Research Database (Denmark)

Fu, Benjamin Mingming; Reidys, Christian

2014-01-01

Shapes of interacting RNA complexes are studied using a filtration via their topological genus. A shape of an RNA complex is obtained by (iteratively) collapsing stacks and eliminating hairpin loops.This shape-projection preserves the topological core of the RNA complex and for fixed topological...... genus there are only finitely many such shapes. Our main result is a new bijection that relates the shapes of RNA complexes with shapes of RNA structures. This allows to compute the shape polynomial of RNA complexes via the shape polynomial of RNA structures. We furthermore present a linear time uniform...... sampling algorithm for shapes of RNA complexes of fixed topological genus....

Technetium-aspirin molecule complexes

International Nuclear Information System (INIS)

El-Shahawy, A.S.; Mahfouz, R.M.; Aly, A.A.M.; El-Zohry, M.

1993-01-01

Technetium-aspirin and technetium-aspirin-like molecule complexes were prepared. The structure of N-acetylanthranilic acid (NAA) has been decided through CNDO calculations. The ionization potential and electron affinity of the NAA molecule as well as the charge densities were calculated. The electronic absorption spectra of Tc(V)-Asp and Tc(V)-ATS complexes have two characteristic absorption bands at 450 and 600 nm, but the Tc(V)-NAA spectrum has one characteristic band at 450 nm. As a comparative study, Mo-ATS complex was prepared and its electronic absorption spectrum is comparable with the Tc-ATS complex spectrum. (author)

The pervasive reach of resource-bounded Kolmogorov complexity in computational complexity theory

Czech Academy of Sciences Publication Activity Database

Allender, E.; Koucký, Michal; Ronneburger, D.; Roy, S.

2011-01-01

Roč. 77, č. 1 (2011), s. 14-40 ISSN 0022-0000 R&D Projects: GA ČR GAP202/10/0854; GA MŠk(CZ) 1M0545; GA AV ČR IAA100190902 Institutional research plan: CEZ:AV0Z10190503 Keywords : Circuit complexity * Distinguishing complexity * FewEXP * Formula size * Kolmogorov complexity Subject RIV: BA - General Mathematics Impact factor: 1.157, year: 2011 http://www.sciencedirect.com/science/article/pii/S0022000010000887

Spectral simplicity of apparent complexity. II. Exact complexities and complexity spectra

Science.gov (United States)

Riechers, Paul M.; Crutchfield, James P.

2018-03-01

The meromorphic functional calculus developed in Part I overcomes the nondiagonalizability of linear operators that arises often in the temporal evolution of complex systems and is generic to the metadynamics of predicting their behavior. Using the resulting spectral decomposition, we derive closed-form expressions for correlation functions, finite-length Shannon entropy-rate approximates, asymptotic entropy rate, excess entropy, transient information, transient and asymptotic state uncertainties, and synchronization information of stochastic processes generated by finite-state hidden Markov models. This introduces analytical tractability to investigating information processing in discrete-event stochastic processes, symbolic dynamics, and chaotic dynamical systems. Comparisons reveal mathematical similarities between complexity measures originally thought to capture distinct informational and computational properties. We also introduce a new kind of spectral analysis via coronal spectrograms and the frequency-dependent spectra of past-future mutual information. We analyze a number of examples to illustrate the methods, emphasizing processes with multivariate dependencies beyond pairwise correlation. This includes spectral decomposition calculations for one representative example in full detail.

Complexity of formation in holography

International Nuclear Information System (INIS)

Chapman, Shira; Marrochio, Hugo; Myers, Robert C.

2017-01-01

It was recently conjectured that the quantum complexity of a holographic boundary state can be computed by evaluating the gravitational action on a bulk region known as the Wheeler-DeWitt patch. We apply this complexity=action duality to evaluate the ‘complexity of formation’ (DOI: 10.1103/PhysRevLett.116.191301; 10.1103/PhysRevD.93.086006), i.e. the additional complexity arising in preparing the entangled thermofield double state with two copies of the boundary CFT compared to preparing the individual vacuum states of the two copies. We find that for boundary dimensions d>2, the difference in the complexities grows linearly with the thermal entropy at high temperatures. For the special case d=2, the complexity of formation is a fixed constant, independent of the temperature. We compare these results to those found using the complexity=volume duality.

Complexity of formation in holography

Energy Technology Data Exchange (ETDEWEB)

Chapman, Shira [Perimeter Institute for Theoretical Physics,Waterloo, ON N2L 2Y5 (Canada); Marrochio, Hugo [Perimeter Institute for Theoretical Physics,Waterloo, ON N2L 2Y5 (Canada); Department of Physics & Astronomy and Guelph-Waterloo Physics Institute,University of Waterloo, Waterloo, ON N2L 3G1 (Canada); Myers, Robert C. [Perimeter Institute for Theoretical Physics,Waterloo, ON N2L 2Y5 (Canada)

2017-01-16

It was recently conjectured that the quantum complexity of a holographic boundary state can be computed by evaluating the gravitational action on a bulk region known as the Wheeler-DeWitt patch. We apply this complexity=action duality to evaluate the ‘complexity of formation’ (DOI: 10.1103/PhysRevLett.116.191301; 10.1103/PhysRevD.93.086006), i.e. the additional complexity arising in preparing the entangled thermofield double state with two copies of the boundary CFT compared to preparing the individual vacuum states of the two copies. We find that for boundary dimensions d>2, the difference in the complexities grows linearly with the thermal entropy at high temperatures. For the special case d=2, the complexity of formation is a fixed constant, independent of the temperature. We compare these results to those found using the complexity=volume duality.

Optimization of wet digestion procedure of blood and tissue for selenium determination by means of 75Se tracer

International Nuclear Information System (INIS)

Holynska, B.; Lipinska, K.

1977-01-01

Selenium-75 tracer has been used for optimization of analytical procedure of selenium determination in blood and tissue. Wet digestion procedure and reduction of selenium to its elemental form with tellurium as coprecipitant have been tested. Recovery of selenium obtained with the use of optimized analytical procedure amounts up 95% and precision is equal to 4.2%. (author)

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. D S Prasad. Articles written in Bulletin of Materials Science. Volume 25 Issue 2 April 2002 pp 79-83 Materials Synthesis. Preparation of high purity tellurium by zone refining · N R Munirathnam D S Prasad Ch Sudheer A J Singh T L Prakash · More Details Abstract Fulltext PDF.

N R Munirathnam

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. N R Munirathnam. Articles written in Bulletin of Materials Science. Volume 25 Issue 2 April 2002 pp 79-83 Materials Synthesis. Preparation of high purity tellurium by zone refining · N R Munirathnam D S Prasad Ch Sudheer A J Singh T L Prakash · More Details Abstract Fulltext ...

Metagenomic analysis of bacterial diversity of Siloam hot water ...

African Journals Online (AJOL)

use

2011-12-07

Dec 7, 2011 ... 14.40. Bicarbonate (HCO3). 107.36. Table 3. Trace elements composition at Siloam Hot spring. Element. Concentration (μg/L) Element. Concentration (μg/L) Element. Concentration μg/L. Antimony. 0.0. Cobalt. 0.1. Strontium. 20.4. Arsenic. 0.3. Copper. 0.0. Tellurium. 0.0. Barium. 4.2. Iodine. 1.9. Thallium.

Aqueous synthesis of porous platinum nanotubes at room temperature and their intrinsic peroxidase-like activity.

Science.gov (United States)

Cai, Kai; Lv, Zhicheng; Chen, Kun; Huang, Liang; Wang, Jing; Shao, Feng; Wang, Yanjun; Han, Heyou

2013-07-11

Platinum nanotubes (PtNTs) exhibiting high porosity were constructed by sacrificing the exterior of tellurium nanowires (TeNWs) and disintegrating the inner part spontaneously in aqueous solution at room temperature, in which the Kirkendall effect may play an important role. The present PtNTs exhibited intrinsic peroxidase-like activity in the presence of H2O2.

Lanthanide complexes with pivaloylacetone

International Nuclear Information System (INIS)

Eliseeva, S.V.; Chugarov, N.V.; Kuz'mina, N.P.; Martynenko, L.I.; Nichiporuk, R.V.; Ivanov, S.A.

2003-01-01

Complexes Ln(pa) 3 ·2H 2 O (Ln=La, Gd, Lu, Hpa - pivaloylacetone) are synthesized and investigated by the methods of element, IR spectroscopic and thermal analyses. Behaviour of the complexes during heating in vacuum is compared with such one for acetylacetonates and dipivaloylmethanates. Structure of the complexes in solution is studied by 1 H NMR and MALDI-MS [ru

Complexity Control of Fast Motion Estimation in H.264/MPEG-4 AVC with Rate-Distortion-Complexity optimization

DEFF Research Database (Denmark)

Wu, Mo; Forchhammer, Søren; Aghito, Shankar Manuel

2007-01-01

A complexity control algorithm for H.264 advanced video coding is proposed. The algorithm can control the complexity of integer inter motion estimation for a given target complexity. The Rate-Distortion-Complexity performance is improved by a complexity prediction model, simple analysis of the pa...... statistics and a control scheme. The algorithm also works well for scene change condition. Test results for coding interlaced video (720x576 PAL) are reported.......A complexity control algorithm for H.264 advanced video coding is proposed. The algorithm can control the complexity of integer inter motion estimation for a given target complexity. The Rate-Distortion-Complexity performance is improved by a complexity prediction model, simple analysis of the past...

Aryldiazo complexes. Syntheses and reactions of new complexes of osmium and ruthenium

International Nuclear Information System (INIS)

Haymore, B.L.; Ibers, J.A.

1975-01-01

Aryldiazo complexes, [M(CO) 2 (NNPh)(PPh 3 ) 2 ][PF 6 ](M = Os, Ru; Ph = C 6 H 5 ), were prepared by allowing diazonium salts to react with M(CO) 3 (PPh 3 ) 2 . Infrared spectra of the Ru complex suggest the presence of two isomers both in solution and in the solid state. These complexes react with a variety of coordinating anions (X - ), to form MX(CO) 2 (NNPh)(PPh 3 ) 2 . The osmium derivatives have ν(NN) near 1455 cm -1 , which is the lowest value yet reported for a nonbridging aryldiazo ligand. The first aryldiazo--hydrido complexes, MH(CO) 2 (NNPh)(PPh 3 ) 2 and MH(CO)(NNPh)(PPh 3 ) 2 , were prepared by deprotonation of the respective phenyldiazene complexes, MH(CO) 2 (HNNPh)(PPh 3 ) 2 + and MH(CO)(HNNPh)(PPh 3 ) 3 + . The compound OsCl 3 (NNPh)(PPh 3 ) 2 was also prepared. A large number of the foregoing complexes were synthesized with selective 2 H and 15 N labels. Infrared and NMR spectra show MX(CO) 2 (NNPh)(PPh 3 ) 2 and the analogous hydrido complex to be pseudooctahedral with trans phosphine ligands, cis carbonyl ligands, and a doubly bent phenyldiazenido (NNPh - ) ligand. Similarly, MH(CO)(NNPh)(PPh 3 ) 2 possesses a trigonal-bipyramidal geometry with trans phosphine ligands and an equatorial, singly bent phenyldiazoniumato (NNPh + ) ligand. Isotopic substitution of the diazo ligand shows that ν(NN) is often vibrationally coupled with phenyl vibrational modes and that two or three bands sometimes shift upon 15 N substitution. Vibrational coupling was also observed in the higher energy region (1850 to 1900 cm -1 ) in the compound RuCl 3 (NNC 6 D 5 )(PPh 3 ) 2 . The wide range in the values of ν(NN), RuCl 3 (NNPh)(PPh 3 ) 2 (1882 cm -1 ) vs. RuCl(CO) 2 (NNPh)(PPh 3 ) 2 (1462 cm -1 ), indicates that the N--N stretching frequencies are sensitive to the electronic and steric environment of the diazo ligand. The aryldiazo complexes are compared with analogous, isoelectronic nitrosyl complexes of Os and Ru

Visual Short-Term Memory Complexity

DEFF Research Database (Denmark)

Sørensen, Thomas Alrik

of objective complexity, it seems that subjective complexity - which is dependent on the familiarity of the stimulus - plays a more important role than the objective visual complexity of the objects stored. In two studies, we explored how familiarity influences the capacity of VSTM. 1) In children learning...... and Cavanagh (2004) have raised the question that the capacity of VSTM is dependent on visual complexity rather than the number of objects. We hypothesise that VSTM capacity is dependent on both the objective and subjective complexity of visual stimuli. Contrary to Alvarez and Cavanagh, who argue for the role...... for letters and pictures remained similar. Our results indicate that VSTM capacity for familiar items is larger irrespective of visual complexity....

Complexity: Outline of the NWO strategic theme Dynamics of complex systems

NARCIS (Netherlands)

Burgers, G.; Doelman, A.; Frenken, K.; Hogeweg, P.; Hommes, C.; van der Maas, H.; Mulder, B.; Stam, K.; van Steen, M.; Zandee, L.

2008-01-01

Dynamics of complex systems is one of the program 5 themes in the NWO (Netherlands Organisation for Scientific Research) strategy for the years 2007-2011. The ambition of the current proposal is to initiate integrated activities in the field of complex systems within the Netherlands, to provide

Complexity : outline of the NWO strategic theme dynamics of complex systems

NARCIS (Netherlands)

Burgers, G.; Doelman, A.; Frenken, K.; Hogeweg, P.; Hommes, C.; Maas, van der H.; Mulder, B.; Stam, K.; Steen, van M.; Zandee, L.

2008-01-01

Dynamics of complex systems is one of the program 5 themes in the NWO (Netherlands Organisation for Scientific Research) strategy for the years 2007-2011. The ambition of the current proposal is to initiate integrated activities in the field of complex systems within the Netherlands, to provide

Coopetition and Complexity : Exploring a Coopetitive Relationship with Complexity

OpenAIRE

Wennberg, Andreas; Persson, Emil

2011-01-01

Cooperation have in previous research been seen as a negative impact on competition and  vice versa. This thesis is building on a concept called coopetition in which cooperation and  competition is studied simultaneously. Coopetition have been studied in terms of the level of  cooperation and competition. However, we found a possible link between coopetition and  complexity in previous literature. Thus, the purpose of this study is to explore whether  complexity can develop an understanding f...

Complexity and Control: Towards a Rigorous Behavioral Theory of Complex Dynamical Systems

Science.gov (United States)

Ivancevic, Vladimir G.; Reid, Darryn J.

We introduce our motive for writing this book on complexity and control with a popular "complexity myth," which seems to be quite wide spread among chaos and complexity theory fashionistas: quote>Low-dimensional systems usually exhibit complex behaviours (which we know fromMay's studies of the Logisticmap), while high-dimensional systems usually exhibit simple behaviours (which we know from synchronisation studies of the Kuramoto model)...quote> We admit that this naive view on complex (e.g., human) systems versus simple (e.g., physical) systems might seem compelling to various technocratic managers and politicians; indeed, the idea makes for appealing sound-bites. However, it is enough to see both in the equations and computer simulations of pendula of various degree - (i) a single pendulum, (ii) a double pendulum, and (iii) a triple pendulum - that this popular myth is plain nonsense. The only thing that we can learn from it is what every tyrant already knows: by using force as a strong means of control, it is possible to effectively synchronise even hundreds of millions of people, at least for a while.

Group 4 Metalloporphyrin diolato Complexes and Catalytic Application of Metalloporphyrins and Related Transition Metal Complexes

Energy Technology Data Exchange (ETDEWEB)

Du, Guodong [Iowa State Univ., Ames, IA (United States)

2003-01-01

In this work, the first examples of group 4 metalloporphyrin 1,2-diolato complexes were synthesized through a number of strategies. In general, treatment of imido metalloporphyrin complexes, (TTP)M=NR, (M = Ti, Zr, Hf), with vicinal diols led to the formation of a series of diolato complexes. Alternatively, the chelating pinacolate complexes could be prepared by metathesis of (TTP)MCl₂ (M = Ti, Hf) with disodium pinacolate. These complexes were found to undergo C-C cleavage reactions to produce organic carbonyl compounds. For titanium porphyrins, treatment of a titanium(II) alkyne adduct, (TTP)Ti(η²-PhC≡CPh), with aromatic aldehydes or aryl ketones resulted in reductive coupling of the carbonyl groups to produce the corresponding diolato complexes. Aliphatic aldehydes or ketones were not reactive towards (TTP)Ti(η²-PhC≡CPh). However, these carbonyl compounds could be incorporated into a diolato complex on reaction with a reactive precursor, (TTP)Ti[O(Ph)₂C(Ph)₂O] to provide unsymmetrical diolato complexes via cross coupling reactions. In addition, an enediolato complex (TTP)Ti(OCPhCPhO) was obtained from the reaction of (TTP)Ti(η²-PhC≡CPh) with benzoin. Titanium porphyrin diolato complexes were found to be intermediates in the (TTP)Ti=O-catalyzed cleavage reactions of vicinal diols, in which atmospheric oxygen was the oxidant. Furthermore, (TTP)Ti=O was capable of catalyzing the oxidation of benzyl alcohol and α-hydroxy ketones to benzaldehyde and α-diketones, respectively. Other high valent metalloporphyrin complexes also can catalyze the oxidative diol cleavage and the benzyl alcohol oxidation reactions with dioxygen. A comparison of Ti(IV) and Sn(IV) porphyrin chemistry was undertaken. While chelated diolato complexes were invariably obtained for titanium porphyrins on treatment with 1,2-diols, the reaction of vicinal diols with tin porphyrins gave a number of products, including mono

Thinking in complexity the complex dynamics of matter, mind, and mankind

CERN Document Server

Mainzer, Klaus

1994-01-01

The theory of nonlinear complex systems has become a successful and widely used problem-solving approach in the natural sciences - from laser physics, quantum chaos and meteorology to molecular modeling in chemistry and computer simulations of cell growth in biology In recent times it has been recognized that many of the social, ecological and political problems of mankind are also of a global, complex and nonlinear nature And one of the most exciting topics of present scientific and public interest is the idea that even the human mind is governed largely by the nonlinear dynamics of complex systems In this wide-ranging but concise treatment Prof Mainzer discusses, in nontechnical language, the common framework behind these endeavours Special emphasis is given to the evolution of new structures in natural and cultural systems and it is seen clearly how the new integrative approach of complexity theory can give new insights that were not available using traditional reductionistic methods

Clearing the complexity: immune complexes and their treatment in lupus nephritis

Directory of Open Access Journals (Sweden)

Catherine Toong

2011-01-01

Full Text Available Catherine Toong1, Stephen Adelstein1, Tri Giang Phan21Department of Clinical Immunology, Royal Prince Alfred Hospital, Missenden Rd, Camperdown, NSW, Australia; 2Immunology Program, Garvan Institute of Medical Research and St. Vincent’s Clinical School, University of New South Wales, Darlinghurst, NSW, AustraliaAbstract: Systemic lupus erythematosus (SLE is a classic antibody-mediated systemic autoimmune disease characterised by the development of autoantibodies to ubiquitous self-antigens (such as antinuclear antibodies and antidouble-stranded DNA antibodies and widespread deposition of immune complexes in affected tissues. Deposition of immune complexes in the kidney results in glomerular damage and occurs in all forms of lupus nephritis. The development of nephritis carries a poor prognosis and high risk of developing end-stage renal failure despite recent therapeutic advances. Here we review the role of DNA-anti-DNA immune complexes in the pathogenesis of lupus nephritis and possible new treatment strategies aimed at their control.Keywords: immune complex, systemic lupus erythematosus, nephritis, therapy

Subgroup complexes

CERN Document Server

Smith, Stephen D

2011-01-01

This book is intended as an overview of a research area that combines geometries for groups (such as Tits buildings and generalizations), topological aspects of simplicial complexes from p-subgroups of a group (in the spirit of Brown, Quillen, and Webb), and combinatorics of partially ordered sets. The material is intended to serve as an advanced graduate-level text and partly as a general reference on the research area. The treatment offers optional tracks for the reader interested in buildings, geometries for sporadic simple groups, and G-equivariant equivalences and homology for subgroup complexes.

Adaptive control for a class of nonlinear complex dynamical systems with uncertain complex parameters and perturbations.

Directory of Open Access Journals (Sweden)

Jian Liu

Full Text Available In this paper, adaptive control is extended from real space to complex space, resulting in a new control scheme for a class of n-dimensional time-dependent strict-feedback complex-variable chaotic (hyperchaotic systems (CVCSs in the presence of uncertain complex parameters and perturbations, which has not been previously reported in the literature. In detail, we have developed a unified framework for designing the adaptive complex scalar controller to ensure this type of CVCSs asymptotically stable and for selecting complex update laws to estimate unknown complex parameters. In particular, combining Lyapunov functions dependent on complex-valued vectors and back-stepping technique, sufficient criteria on stabilization of CVCSs are derived in the sense of Wirtinger calculus in complex space. Finally, numerical simulation is presented to validate our theoretical results.

Adaptive control for a class of nonlinear complex dynamical systems with uncertain complex parameters and perturbations.

Science.gov (United States)

Liu, Jian; Liu, Kexin; Liu, Shutang

2017-01-01

In this paper, adaptive control is extended from real space to complex space, resulting in a new control scheme for a class of n-dimensional time-dependent strict-feedback complex-variable chaotic (hyperchaotic) systems (CVCSs) in the presence of uncertain complex parameters and perturbations, which has not been previously reported in the literature. In detail, we have developed a unified framework for designing the adaptive complex scalar controller to ensure this type of CVCSs asymptotically stable and for selecting complex update laws to estimate unknown complex parameters. In particular, combining Lyapunov functions dependent on complex-valued vectors and back-stepping technique, sufficient criteria on stabilization of CVCSs are derived in the sense of Wirtinger calculus in complex space. Finally, numerical simulation is presented to validate our theoretical results.

Complexity a very short introduction

CERN Document Server

Holland, John H

2014-01-01

The importance of complexity is well-captured by Hawking's comment: "Complexity is the science of the 21st century". From the movement of flocks of birds to the Internet, environmental sustainability, and market regulation, the study and understanding of complex non-linear systems has become highly influential over the last 30 years. In this Very Short Introduction, one of the leading figures in the field, John Holland, introduces the key elements and conceptual framework of complexity. From complex physical systems such as fluid flow and the difficulties of predicting weather, to complex adaptive systems such as the highly diverse and interdependent ecosystems of rainforests, he combines simple, well-known examples - Adam Smith's pin factory, Darwin's comet orchid, and Simon's 'watchmaker' - with an account of the approaches, involving agents and urn models, taken by complexity theory. ABOUT THE SERIES: The Very Short Introductions series from Oxford University Press contains hundreds of titles in almost eve...

Quantifying Complexity in Quantum Phase Transitions via Mutual Information Complex Networks.

Science.gov (United States)

Valdez, Marc Andrew; Jaschke, Daniel; Vargas, David L; Carr, Lincoln D

2017-12-01

We quantify the emergent complexity of quantum states near quantum critical points on regular 1D lattices, via complex network measures based on quantum mutual information as the adjacency matrix, in direct analogy to quantifying the complexity of electroencephalogram or functional magnetic resonance imaging measurements of the brain. Using matrix product state methods, we show that network density, clustering, disparity, and Pearson's correlation obtain the critical point for both quantum Ising and Bose-Hubbard models to a high degree of accuracy in finite-size scaling for three classes of quantum phase transitions, Z_{2}, mean field superfluid to Mott insulator, and a Berzinskii-Kosterlitz-Thouless crossover.

Quantifying Complexity in Quantum Phase Transitions via Mutual Information Complex Networks

Science.gov (United States)

Valdez, Marc Andrew; Jaschke, Daniel; Vargas, David L.; Carr, Lincoln D.

2017-12-01

We quantify the emergent complexity of quantum states near quantum critical points on regular 1D lattices, via complex network measures based on quantum mutual information as the adjacency matrix, in direct analogy to quantifying the complexity of electroencephalogram or functional magnetic resonance imaging measurements of the brain. Using matrix product state methods, we show that network density, clustering, disparity, and Pearson's correlation obtain the critical point for both quantum Ising and Bose-Hubbard models to a high degree of accuracy in finite-size scaling for three classes of quantum phase transitions, Z2, mean field superfluid to Mott insulator, and a Berzinskii-Kosterlitz-Thouless crossover.

EPR invastigation of glasses on the base of the oxides of vanadium and tellurium

International Nuclear Information System (INIS)

Imanov, L.M; Ibragimov, Z.A.

1978-01-01

The results of investigation of EPR spectra of the nV 2 O 5 (100-n)TeO 2 binary system in the range from 95 to 5 mol % V 2 O 5 with the 5 mol % step on the DRON-2 installation (X-ray diffraction measurements) are presented. The EPR spectra were read out on the RE-1301 spectrometer at liquid nitrogen and room temperatures. The concentration of the EPR centres was determined by comparing it with the signal from the known number of Cu 2+ ions in the CuSO 4 x5H 2 O crystal. It is established that the VO 2+ complexes were the EPR centres. In all prepared samples the EPR spectra were observed, and at n=70 the SFS components were revealed both in the crystalline (with the TeO 2 content up to 30 mol %) and in amorphous states. The singularities of the EPR spectrum are discussed on the basis of the spin-hamiltonian with axial asymmetry. The dependence of the spin-hamiltonian components on the content was revealed and the P=670 value characterizing the average value of the distance between the nucleus and noncoupled electron is found. Observation of the line with well resoluted SFS components in the amorphous samples is explained by 'a great freedom'' of paramagnetic ions in the choice of close environment, and consequently the field of ligand atoms localizing in the paramagnetic ion produces the ''strong field'' effect (D, E>>GβH, G=1.985+-0.005) and removes degeneration due to the presence of the I=7/2 nuclear momentum of the V 4+ ion. Conservation of the SFS lines even at room temperature is connected with great scattering of the spin-lattice relaxation time

Innovation in a complex environment

Directory of Open Access Journals (Sweden)

René Pellissier

2012-11-01

Objectives: The study objectives were, firstly, to establish the determinants for complexity and how these can be addressed from a design point of view in order to ensure innovation success and, secondly, to determine how this changes innovation forms and applications. Method: Two approaches were offered to deal with a complex environment – one allowing for complexity for organisational innovation and the other introducing reductionism to minimise complexity. These approaches were examined in a qualitative study involving case studies, open-ended interviews and content analysis between seven developing economy (South African organisations and seven developed economy (US organisations. Results: This study presented a proposed framework for (organisational innovation in a complex environment versus a framework that minimises complexity. The comparative organisational analysis demonstrated the importance of initiating organisational innovation to address internal and external complexity, with the focus being on the leadership actions, their selected operating models and resultant organisational innovations designs, rather than on technological innovations. Conclusion: This study cautioned the preference for technological innovation within organisations and suggested alternative innovation forms (such as organisational and management innovation be used to remain competitive in a complex environment.

COMPLEX PROMOTIONSIN RETAIL

Directory of Open Access Journals (Sweden)

O. Yusupova

2015-10-01

Full Text Available Complex promotions used by retailers introduce to the consumers several rules that must be satisfied in order to get some benefits and usually refer to multiple products (e.g. “buy two, get one free”. Rules of complex promotions can be quite sophisticated and complicated themselves. Since diversity of complex promotions limited only by marketers’ imagination we can observe broad variety of promotions’ rules and representa¬tions of those rules in retailers’ commercials. Such diversification makes no good for fellow scientist who’s trying to sort all type of promotions into the neatly organized classification. Although we can simple add every single set of rules offered by retailers as a separate form of sales promotion it seems not to be the best way of dealing with such a problem. The better way is to realize that mechanisms underlying that variety of promotions are basically the same, namely changes in demand or quantity demanded. Those two concepts alone provide powerful insight into classification of complex promotions and allow us to comprehend the variety of promotions offered by marketers nowadays.

Nuclear weapons complex

International Nuclear Information System (INIS)

Peach, J.D.

1991-02-01

In this paper, GAO provides its views on DOE's January 1991 Nuclear Weapons Complex Reconfiguration Study. GAO believes that DOE's new reconfiguration study provides a starting point for reaching agreement on solutions to many of the complex's problems. Key decisions still need to be made about the size of the complex, where to relocate plutonium operations, what technologies should be used for new tritium production, and what to do with excess plutonium. The total cost for reconfiguring and modernizing is still uncertain and some management issues remain unresolved. Congress faces a difficult task in making these decisions given the conflicting demands for scare resources in a time of growing budget deficits and war in the Persian Gulf

The SEA complex – the beginning

Directory of Open Access Journals (Sweden)

Dokudovskaya S. S.

2012-07-01

Full Text Available The presence of distinctive internal membrane compartments, dynamically connected via selective transport pathways, is a hallmark of eukaryotic cells. Many of the proteins required for formation and maintenance of these compartments share an evolutionary history. We have recently identified a new conserved protein complex – the SEA complex – that possesses proteins with structural characteristics similar to the membrane coating complexes such as the nuclear pore complex (NPC, the COPII vesicle coating complex and HOPS/CORVET tethering complexes. The SEA complex in yeast is dynamically associated to the vacuole. The data on the function of the SEA complex remain extremely limited. Here we will discuss a possible role of the SEA complex based on the data from genetic assays and a number of functional studies in both yeast and other eukaryotes.

Qubit Complexity of Continuous Problems

National Research Council Canada - National Science Library

Papageorgiou, A; Traub, J. F

2005-01-01

.... The authors show how to obtain the classical query complexity for continuous problems. They then establish a simple formula for a lower bound on the qubit complexity in terms of the classical query complexity...

Innovation in a complex environment

Directory of Open Access Journals (Sweden)

René Pellissier

2012-02-01

Full Text Available Background: As our world becomes more global and competitive yet less predictable, the focus seems to be increasingly on looking to innovation activities to remain competitive. Although there is little doubt that a nation’s competitiveness is embedded in its innovativeness, the complex environment should not be ignored. Complexity is not accounted for in balance sheets or reported in reports; it becomes entrenched in every activity in the organisation. Innovation takes many forms and comes in different shapes.Objectives: The study objectives were, firstly, to establish the determinants for complexity and how these can be addressed from a design point of view in order to ensure innovation success and, secondly, to determine how this changes innovation forms and applications.Method: Two approaches were offered to deal with a complex environment – one allowing for complexity for organisational innovation and the other introducing reductionism to minimise complexity. These approaches were examined in a qualitative study involving case studies, open-ended interviews and content analysis between seven developing economy (South African organisations and seven developed economy (US organisations.Results: This study presented a proposed framework for (organisational innovation in a complex environment versus a framework that minimises complexity. The comparative organisational analysis demonstrated the importance of initiating organisational innovation to address internal and external complexity, with the focus being on the leadership actions, their selected operating models and resultant organisational innovations designs, rather than on technological innovations.Conclusion: This study cautioned the preference for technological innovation within organisations and suggested alternative innovation forms (such as organisational and management innovation be used to remain competitive in a complex environment. 

SCAR/WAVE: A complex issue.

Science.gov (United States)

Davidson, Andrew J; Insall, Robert H

2013-11-01

The SCAR/WAVE complex drives the actin polymerisation that underlies protrusion of the front of the cell and thus drives migration. However, it is not understood how the activity of SCAR/WAVE is regulated to generate the infinite range of cellular shape changes observed during cell motility. What are the relative roles of the subunits of the SCAR/WAVE complex? What signaling molecules do they interact with? And how does the complex integrate all this information in order to control the temporal and spatial polymerisation of actin during protrusion formation? Unfortunately, the interdependence of SCAR complex members has made genetic dissection hard. In our recent paper,(1) we describe stabilization of the Dictyostelium SCAR complex by a small fragment of Abi. Here we summarize the main findings and discuss how this approach can help reveal the inner workings of this impenetrable complex.

Complex manifolds

CERN Document Server

Morrow, James

2006-01-01

This book, a revision and organization of lectures given by Kodaira at Stanford University in 1965-66, is an excellent, well-written introduction to the study of abstract complex (analytic) manifolds-a subject that began in the late 1940's and early 1950's. It is largely self-contained, except for some standard results about elliptic partial differential equations, for which complete references are given. -D. C. Spencer, MathSciNet The book under review is the faithful reprint of the original edition of one of the most influential textbooks in modern complex analysis and geometry. The classic

Hypoxia targeting copper complexes

International Nuclear Information System (INIS)

Dearling, J.L.

1998-11-01

The importance and incidence of tumour hypoxia, its measurement and current treatments available, including pharmacological and radiopharmacological methods of targeting hypoxia, are discussed. A variety of in vitro and in vivo methods for imposing hypoxia have been developed and are reviewed. Copper, its chemistry, biochemistry and radiochemistry, the potential for use of copper radionuclides and its use to date in this field is considered with particular reference to the thiosemicarbazones. Their biological activity, metal chelation, in vitro and in vivo studies of their radiocopper complexes and the potential for their use as hypoxia targeting radiopharmaceuticals is described. The reduction of the copper(II) complex to copper(l), its pivotal importance in their biological behaviour, and the potential for manipulation of this to effect hypoxia selectivity are described. An in vitro method for assessing the hypoxia selectivity of radiopharmaceuticals is reported. The rapid deoxygenation and high viability of a mammalian cell culture in this system is discussed and factors which may affect the cellular uptake of a radiopharmaceutical are described. The design, synthesis and complexation with copper and radiocopper of a range of bis(thiosemicarbazones) is reported. Synthesis of these compounds is simple giving high yields of pure products. The characteristics of the radiocopper complexes ( 64 Cu) including lipophilicity and redox activity are reported (reduction potentials in the range -0.314 - -0.590 V). High cellular uptakes of the radiocopper complexes of the ligands, in hypoxic and normoxic EMT6 and CHO320 cells, were observed. Extremes of selectivity are shown ranging from the hypoxia selective 64 Cu(II)ATSM to normoxic cell selective 64 Cu(II)GTS. The selectivities observed are compared with the physico chemical characteristics of the complexes. A good correlation exists between selectivity of the complex and its Cu(II)/Cu(I) reduction potential, with hypoxia

Complex Systems and Dependability

CERN Document Server

Zamojski, Wojciech; Sugier, Jaroslaw

2012-01-01

Typical contemporary complex system is a multifaceted amalgamation of technical, information, organization, software and human (users, administrators and management) resources. Complexity of such a system comes not only from its involved technical and organizational structure but mainly from complexity of information processes that must be implemented in the operational environment (data processing, monitoring, management, etc.). In such case traditional methods of reliability analysis focused mainly on technical level are usually insufficient in performance evaluation and more innovative meth

Complexity Management - A multiple case study analysis on control and reduction of complexity costs

DEFF Research Database (Denmark)

Myrodia, Anna

of products, with features more custom-made to cover individual needs, both regarding characteristics of products and support services. This necessity leads to a considerable increase of the complexity in the company, which affects the product portfolio, production and supply chain, market segments......, IT systems, and business processes. In order to identify and eliminate complexity, several approaches are used, both by researchers and practitioners. The purpose of this thesis is to contribute to the existing knowledge of complexity management theory. This research focuses on the relationship between......Complexity tends to be arguably the biggest challenge of manufacturing companies. The motivation of further studying complexity is a combination between the existing literature and the practical experiences from the industry. Based on the latest trend companies are trying to supply a growing mix...

On dependence of stability of lanthanum complexes with aminopolycarboxylic acids on the complex structure

International Nuclear Information System (INIS)

Poluehktov, N.S.; Meshkova, S.B.; Danilkovich, M.M.; Topilova, Z.M.

1985-01-01

Regularities in changes of stability constants of lanthanum complexes with aminopolycarboxylic acids (APA) versus their structure are studied, The stability of lathanum-APA complexes depends mainly on the number of carboxyl groups in a ligand molecule. At that, the highest stability constant is characteristic of a complex with a ligand, containing 3 nitrogen atoms and 5 carboxyl groups, in the presenoe of which the lanthanum ion coordination sphere gets satupated. The oxyethy group introduction into a ligand molecule also improves the lanthanum complex stability but to a lesser degree than during the introduction of a carboxyl group. The number of nitrogen atoms in a ligand polecule affects insignificantly the complex stability constant value, and the elongation of a chain of CH 2 groups, separating nitrogen atoms, reduces the constant to a -0.6 power

Complex Projective Synchronization in Drive-Response Stochastic Complex Networks by Impulsive Pinning Control

Directory of Open Access Journals (Sweden)

Xuefei Wu

2014-01-01

Full Text Available The complex projective synchronization in drive-response stochastic coupled networks with complex-variable systems is considered. The impulsive pinning control scheme is adopted to achieve complex projective synchronization and several simple and practical sufficient conditions are obtained in a general drive-response network. In addition, the adaptive feedback algorithms are proposed to adjust the control strength. Several numerical simulations are provided to show the effectiveness and feasibility of the proposed methods.

MANAGEMENT OF SPORT COMPLEXES

Directory of Open Access Journals (Sweden)

Marian STAN

2015-07-01

Full Text Available The actuality of the investigated theme. Nowadays, human evolution, including his intellectual development, proves the fact that especially the creation manpower and the employment was the solution of all life’s ambitions in society. So, the fact is that in reality, man is the most important capital of the society. Also, in an individual’s life, the practice of sport plays a significant role and that’s why the initiation, the launch and the management of sports complexes activity reveal the existence of specific management features that we will identify and explain in the current study. The aim of the research refers to the elaboration of a theoretical base of the management of the sport complexes, to the pointing of the factors that influence the efficient existence and function of a sport complex in our country and to the determination of the responsibilities that have a manager who directs successfully the activity of the sport complexes. The investigation is based on theoretical methods, such as: scientific documentation, analysis, synthesis, comparison and on empirical research methods, like: study of researched literature and observation. The results of the research indicate the fact that the profitability of a sport complex must assure a particular structure to avoid the bankruptcy risk and also, that the administration of the sport complexes activity must keep in view the reliable functions of the contemporaneous management.

COMPLEXITY AND UNIVERSITY

Directory of Open Access Journals (Sweden)

Edna Lemes Martins Pereira

2013-12-01

Full Text Available Economic globalization affects different countries on the globe, has positive effects mainly related to access to communication, which promotes the exchange of ideas, information, products and quality of life. However, extends numerous negative aspects such as marginalization, economic dependencies, political, cultural, scientific, educational accentuate social inequalities and cultural conflicts and territorial. In this article it is a dialogue with authors (Cunha 2009; BARNETT 2005; MORIN 1999, 2006, among others, who understand these changes in society from the contemporary world as conceived as the "Complexity era" or "supercomplexity". To understand and cope with this reality, they propose a paradigm that is able to overcome the fragmentation and reductionism of knowledge and to relate the multiple approaches and visions to meet the complexity of reality. Although this paper presents proposals to the aforementioned authors point to education and the university found in this tangle of interconnected global transformations, given the need to be subject to act in a complex reality that requires critical and self-critical professionals, able to think about their own ability to think, understand and act within this complex context.

Cooperativity of complex salt bridges

OpenAIRE

Gvritishvili, Anzor G.; Gribenko, Alexey V.; Makhatadze, George I.

2008-01-01

The energetic contribution of complex salt bridges, in which one charged residue (anchor residue) forms salt bridges with two or more residues simultaneously, has been suggested to have importance for protein stability. Detailed analysis of the net energetics of complex salt bridge formation using double- and triple-mutant cycle analysis revealed conflicting results. In two cases, it was shown that complex salt bridge formation is cooperative, i.e., the net strength of the complex salt bridge...

Study of complex modes

International Nuclear Information System (INIS)

Pastrnak, J.W.

1986-01-01

This eighteen-month study has been successful in providing the designer and analyst with qualitative guidelines on the occurrence of complex modes in the dynamics of linear structures, and also in developing computer codes for determining quantitatively which vibration modes are complex and to what degree. The presence of complex modes in a test structure has been verified. Finite element analysis of a structure with non-proportional dumping has been performed. A partial differential equation has been formed to eliminate possible modeling errors

Optical characterization of wide-gap detector-grade semiconductors

International Nuclear Information System (INIS)

Elshazly, E.S.

2011-01-01

Wide bandgap semiconductors are being widely investigated because they have the potential to satisfy the stringent material requirements of high resolution, room temperature gamma-ray spectrometers. In particular, Cadmium Zinc Telluride (Cd 1-x Zn x Te, x∼0.1) and Thallium Bromide (Tl Br), due to their combination of high resistivity, high atomic number and good electron mobility, have became very promising candidates for use in X- and gamma-ray detectors operating at room temperature. In this study, carrier trapping times were measured in CZT and Tl Br as a function of temperature and material quality. Carrier lifetimes and tellurium inclusion densities were measured in detector-grade Cadmium Zinc Telluride (CZT) crystals grown by the High Pressure Bridgman method and Modified Bridgman method. Excess carriers were produced in the material using a pulsed YAG laser with a 1064 nm wavelength and 7 ns pulse width. Infrared microscopy was used to measure the tellurium defect densities in CZT crystals. The electronic decay was optically measured at room temperature. Spatial mapping of lifetimes and defect densities in CZT was performed to determine the relationship between defect density and electronic decay. A significant and strong correlation was found between the volume fraction of tellurium inclusions and the carrier trapping time. Carrier trapping times and tellurium inclusions were measured in CZT in the temperature range from 300 K to 110 K and the results were analyzed using a theoretical trapping model. Spatial mapping of carrier trapping times and defect densities in CZT was performed to determine the relationship between defect density and electronic decay. While a strong correlation between trapping time and defect density of tellurium inclusions was observed, there was no significant change in the trap energy. Carrier trapping times were measured in detector grade thallium bromide (Tl Br) and compared with the results for cadmium zinc telluride (CZT) in

Managing complexity insights, concepts, applications

CERN Document Server

Helbing, Dirk

2007-01-01

Each chapter in Managing Complexity focuses on analyzing real-world complex systems and transferring knowledge from the complex-systems sciences to applications in business, industry and society. The interdisciplinary contributions range from markets and production through logistics, traffic control, and critical infrastructures, up to network design, information systems, social conflicts and building consensus. They serve to raise readers' awareness concerning the often counter-intuitive behavior of complex systems and to help them integrate insights gained in complexity research into everyday planning, decision making, strategic optimization, and policy. Intended for a broad readership, the contributions have been kept largely non-technical and address a general, scientifically literate audience involved in corporate, academic, and public institutions.

Complexation of buffer constituents with neutral complexation agents: part II. Practical impact in capillary zone electrophoresis.

Science.gov (United States)

Beneš, Martin; Riesová, Martina; Svobodová, Jana; Tesařová, Eva; Dubský, Pavel; Gaš, Bohuslav

2013-09-17

This article elucidates the practical impact of the complexation of buffer constituents with complexation agents on electrophoretic results, namely, complexation constant determination, system peak development, and proper separation of analytes. Several common buffers, which were selected based on the pH study in Part I of this paper series (Riesová, M.; Svobodová, J.; Tošner, Z.; Beneš, M.; Tesařová, E.; Gaš, B. Anal. Chem., 2013, DOI: 10.1021/ac4013804); e.g., CHES, MES, MOPS, Tricine were used to demonstrate behavior of such complex separation systems. We show that the value of a complexation constant determined in the interacting buffers environment depends not only on the analyte and complexation agent but it is also substantially affected by the type and concentration of buffer constituents. As a result, the complexation parameters determined in the interacting buffers cannot be regarded as thermodynamic ones and may provide misleading information about the strength of complexation of the compound of interest. We also demonstrate that the development of system peaks in interacting buffer systems significantly differs from the behavior known for noncomplexing systems, as the mobility of system peaks depends on the concentration and type of neutral complexation agent. Finally, we show that the use of interacting buffers can totally ruin the results of electrophoretic separation because the buffer properties change as the consequence of the buffer constituents' complexation. As a general conclusion, the interaction of buffer constituents with the complexation agent should always be considered in any method development procedures.

Quantify the complexity of turbulence

Science.gov (United States)

Tao, Xingtian; Wu, Huixuan

2017-11-01

Many researchers have used Reynolds stress, power spectrum and Shannon entropy to characterize a turbulent flow, but few of them have measured the complexity of turbulence. Yet as this study shows, conventional turbulence statistics and Shannon entropy have limits when quantifying the flow complexity. Thus, it is necessary to introduce new complexity measures- such as topology complexity and excess information-to describe turbulence. Our test flow is a classic turbulent cylinder wake at Reynolds number 8100. Along the stream-wise direction, the flow becomes more isotropic and the magnitudes of normal Reynolds stresses decrease monotonically. These seem to indicate the flow dynamics becomes simpler downstream. However, the Shannon entropy keeps increasing along the flow direction and the dynamics seems to be more complex, because the large-scale vortices cascade to small eddies, the flow is less correlated and more unpredictable. In fact, these two contradictory observations partially describe the complexity of a turbulent wake. Our measurements (up to 40 diameters downstream the cylinder) show that the flow's degree-of-complexity actually increases firstly and then becomes a constant (or drops slightly) along the stream-wise direction. University of Kansas General Research Fund.

BRAND program complex

International Nuclear Information System (INIS)

Androsenko, A.A.; Androsenko, P.A.

1983-01-01

A description is given of the structure, input procedure and recording rules of initial data for the BRAND programme complex intended for the Monte Carlo simulation of neutron physics experiments. The BRAND complex ideology is based on non-analogous simulation of the neutron and photon transport process (statistic weights are used, absorption and escape of particles from the considered region is taken into account, shifted readouts from a coordinate part of transition nucleus density are applied, local estimations, etc. are used). The preparation of initial data for three sections is described in detail: general information for Monte Carlo calculation, source definition and data for describing the geometry of the system. The complex is to be processed with the BESM-6 computer, the basic programming lan-- guage is FORTRAN, volume - more than 8000 operators

Identification of a small TAF complex and its role in the assembly of TAF-containing complexes.

Science.gov (United States)

Demény, Màté A; Soutoglou, Evi; Nagy, Zita; Scheer, Elisabeth; Jànoshàzi, Agnes; Richardot, Magalie; Argentini, Manuela; Kessler, Pascal; Tora, Laszlo

2007-03-21

TFIID plays a role in nucleating RNA polymerase II preinitiation complex assembly on protein-coding genes. TFIID is a multisubunit complex comprised of the TATA box binding protein (TBP) and 14 TBP-associated factors (TAFs). Another class of multiprotein transcriptional regulatory complexes having histone acetyl transferase (HAT) activity, and containing TAFs, includes TFTC, STAGA and the PCAF/GCN5 complex. Looking for as yet undiscovered subunits by a proteomic approach, we had identified TAF8 and SPT7L in human TFTC preparations. Subsequently, however, we demonstrated that TAF8 was not a stable component of TFTC, but that it is present in a small TAF complex (SMAT), containing TAF8, TAF10 and SPT7L, that co-purified with TFTC. Thus, TAF8 is a subunit of both TFIID and SMAT. The latter has to be involved in a pathway of complex formation distinct from the other known TAF complexes, since these three histone fold (HF)-containing proteins (TAF8, TAF10 and SPT7L) can never be found together either in TFIID or in STAGA/TFTC HAT complexes. Here we show that TAF8 is absolutely necessary for the integration of TAF10 in a higher order TFIID core complex containing seven TAFs. TAF8 forms a heterodimer with TAF10 through its HF and proline rich domains, and also interacts with SPT7L through its C-terminal region, and the three proteins form a complex in vitro and in vivo. Thus, the TAF8-TAF10 and TAF10-SPT7L HF pairs, and also the SMAT complex, seem to be important regulators of the composition of different TFIID and/or STAGA/TFTC complexes in the nucleus and consequently may play a role in gene regulation.

Complexity science and leadership in healthcare.

Science.gov (United States)

Burns, J P

2001-10-01

The emerging field of complexity science offers an alternative leadership strategy for the chaotic, complex healthcare environment. A survey revealed that healthcare leaders intuitively support principles of complexity science. Leadership that uses complexity principles offers opportunities in the chaotic healthcare environment to focus less on prediction and control and more on fostering relationships and creating conditions in which complex adaptive systems can evolve to produce creative outcomes.

Complex Functions with GeoGebra

Science.gov (United States)

Breda, Ana Maria D'azevedo; Dos Santos, José Manuel Dos Santos

2016-01-01

Complex functions, generally feature some interesting peculiarities, seen as extensions of real functions. The visualization of complex functions properties usually requires the simultaneous visualization of two-dimensional spaces. The multiple Windows of GeoGebra, combined with its ability of algebraic computation with complex numbers, allow the…

Complex DNA structures and structures of DNA complexes

International Nuclear Information System (INIS)

Chazin, W.J.; Carlstroem, G.; Shiow-Meei Chen; Miick, S.; Gomez-Paloma, L.; Smith, J.; Rydzewski, J.

1994-01-01

Complex DNA structures (for example, triplexes, quadruplexes, junctions) and DNA-ligand complexes are more difficult to study by NMR than standard DNA duplexes are because they have high molecular weights, show nonstandard or distorted local conformations, and exhibit large resonance linewidths and severe 1 H spectral overlap. These systems also tend to have limited solubility and may require specialized solution conditions to maintain favorable spectral characteristics, which adds to the spectroscopic difficulties. Furthermore, with more atoms in the system, both assignment and structure calculation become more challenging. In this article, we focus on demonstrating the current status of NMR studies of such systems and the limitations to further progress; we also indicate in what ways isotopic enrichment can be useful

Complex DNA structures and structures of DNA complexes

Energy Technology Data Exchange (ETDEWEB)

Chazin, W.J.; Carlstroem, G.; Shiow-Meei Chen; Miick, S.; Gomez-Paloma, L.; Smith, J.; Rydzewski, J. [Scripps Research Institute, La Jolla, CA (United States)

1994-12-01

Complex DNA structures (for example, triplexes, quadruplexes, junctions) and DNA-ligand complexes are more difficult to study by NMR than standard DNA duplexes are because they have high molecular weights, show nonstandard or distorted local conformations, and exhibit large resonance linewidths and severe {sup 1}H spectral overlap. These systems also tend to have limited solubility and may require specialized solution conditions to maintain favorable spectral characteristics, which adds to the spectroscopic difficulties. Furthermore, with more atoms in the system, both assignment and structure calculation become more challenging. In this article, we focus on demonstrating the current status of NMR studies of such systems and the limitations to further progress; we also indicate in what ways isotopic enrichment can be useful.

Oligocyclopentadienyl transition metal complexes

Energy Technology Data Exchange (ETDEWEB)

de Azevedo, Cristina G.; Vollhardt, K. Peter C.

2002-01-18

Synthesis, characterization, and reactivity studies of oligocyclopentadienyl transition metal complexes, namely those of fulvalene, tercyclopentadienyl, quatercyclopentadienyl, and pentacyclopentadienyl(cyclopentadienyl) are the subject of this account. Thermal-, photo-, and redox chemistries of homo- and heteropolynuclear complexes are described.

Measuring Complexity of SAP Systems

Directory of Open Access Journals (Sweden)

Ilja Holub

2016-10-01

Full Text Available The paper discusses the reasons of complexity rise in ERP system SAP R/3. It proposes a method for measuring complexity of SAP. Based on this method, the computer program in ABAP for measuring complexity of particular SAP implementation is proposed as a tool for keeping ERP complexity under control. The main principle of the measurement method is counting the number of items or relations in the system. The proposed computer program is based on counting of records in organization tables in SAP.

Exotic plant species around Jeongeup Research Complex and RFT industrial complex

International Nuclear Information System (INIS)

Kim, Jin Kyu; Cha, Min Kyoung; Ryu, Tae Ho; Lee, Yun Jong; Kim, Jin Hong

2015-01-01

In Shinjeong-dong of Jeongeup, there are three government-supported research institutes and an RFT industrial complex which is currently being established. Increased human activities can affect flora and fauna as a man-made pressure onto the region. As a baseline study, status of exotic plants was investigated prior to a full operation of the RFT industrial complex. A total of 54 species and 1 variety of naturalized or introduced plants were found in the study area. Among them, three species (Ambrosia artemisifolia var. elatior, Rumex acetocella and Aster pilosus) belong to 'nuisance species', and four species (Phytolacca americana, Iopomoea hederacea, Ereechtites hieracifolia and Rudbeckia laciniata) to ‘monitor species’ designated by the ministry of Environment. Some of naturalized trees and plants were intentionally introduced in this area, while others naturally immigrated. Physalis angulata seems to immigrate in the study area in the form of mixture with animal feeds as its distribution coincided with the transportation route of the animal feeds. Liquidambar styraciflua is amenable to the ecological investigation on the possible expansion of the species to the nearby Naejang National Park as its leave shape and autumn color are very similar to those of maple trees. The number of naturalized plants around the RFT industrial complex will increase with an increase in floating population, in human activities in association with constructions of factories and operations of the complex. The result of this study provides baseline data for assessing the ecological change of the region according to the operation of the RFT industrial complex

Exotic plant species around Jeongeup Research Complex and RFT industrial complex

Energy Technology Data Exchange (ETDEWEB)

Kim, Jin Kyu; Cha, Min Kyoung; Ryu, Tae Ho; Lee, Yun Jong; Kim, Jin Hong [Advanced Radiation Technology Institute, Korea Atomic Energy Research Institute, Jeongeup(Korea, Republic of)

2015-08-15

In Shinjeong-dong of Jeongeup, there are three government-supported research institutes and an RFT industrial complex which is currently being established. Increased human activities can affect flora and fauna as a man-made pressure onto the region. As a baseline study, status of exotic plants was investigated prior to a full operation of the RFT industrial complex. A total of 54 species and 1 variety of naturalized or introduced plants were found in the study area. Among them, three species (Ambrosia artemisifolia var. elatior, Rumex acetocella and Aster pilosus) belong to 'nuisance species', and four species (Phytolacca americana, Iopomoea hederacea, Ereechtites hieracifolia and Rudbeckia laciniata) to ‘monitor species’ designated by the ministry of Environment. Some of naturalized trees and plants were intentionally introduced in this area, while others naturally immigrated. Physalis angulata seems to immigrate in the study area in the form of mixture with animal feeds as its distribution coincided with the transportation route of the animal feeds. Liquidambar styraciflua is amenable to the ecological investigation on the possible expansion of the species to the nearby Naejang National Park as its leave shape and autumn color are very similar to those of maple trees. The number of naturalized plants around the RFT industrial complex will increase with an increase in floating population, in human activities in association with constructions of factories and operations of the complex. The result of this study provides baseline data for assessing the ecological change of the region according to the operation of the RFT industrial complex.

A Memristor-Based Hyperchaotic Complex Lü System and Its Adaptive Complex Generalized Synchronization

Directory of Open Access Journals (Sweden)

Shibing Wang

2016-02-01

Full Text Available This paper introduces a new memristor-based hyperchaotic complex Lü system (MHCLS and investigates its adaptive complex generalized synchronization (ACGS. Firstly, the complex system is constructed based on a memristor-based hyperchaotic real Lü system, and its properties are analyzed theoretically. Secondly, its dynamical behaviors, including hyperchaos, chaos, transient phenomena, as well as periodic behaviors, are explored numerically by means of bifurcation diagrams, Lyapunov exponents, phase portraits, and time history diagrams. Thirdly, an adaptive controller and a parameter estimator are proposed to realize complex generalized synchronization and parameter identification of two identical MHCLSs with unknown parameters based on Lyapunov stability theory. Finally, the numerical simulation results of ACGS and its applications to secure communication are presented to verify the feasibility and effectiveness of the proposed method.

Complexity of Economical Systems

Directory of Open Access Journals (Sweden)

G. P. Pavlos

2015-01-01

Full Text Available In this study new theoretical concepts are described concerning the interpretation of economical complex dynamics. In addition a summary of an extended algorithm of nonlinear time series analysis is provided which is applied not only in economical time series but also in other physical complex systems (e.g. [22, 24]. In general, Economy is a vast and complicated set of arrangements and actions wherein agents—consumers, firms, banks, investors, government agencies—buy and sell, speculate, trade, oversee, bring products into being, offer services, invest in companies, strategize, explore, forecast, compete, learn, innovate, and adapt. As a result the economic and financial variables such as foreign exchange rates, gross domestic product, interest rates, production, stock market prices and unemployment exhibit large-amplitude and aperiodic fluctuations evident in complex systems. Thus, the Economics can be considered as spatially distributed non-equilibrium complex system, for which new theoretical concepts, such as Tsallis non extensive statistical mechanics and strange dynamics, percolation, nonGaussian, multifractal and multiscale dynamics related to fractional Langevin equations can be used for modeling and understanding of the economical complexity locally or globally.

Complexity and Dynamical Depth

Directory of Open Access Journals (Sweden)

Terrence Deacon

2014-07-01

Full Text Available We argue that a critical difference distinguishing machines from organisms and computers from brains is not complexity in a structural sense, but a difference in dynamical organization that is not well accounted for by current complexity measures. We propose a measure of the complexity of a system that is largely orthogonal to computational, information theoretic, or thermodynamic conceptions of structural complexity. What we call a system’s dynamical depth is a separate dimension of system complexity that measures the degree to which it exhibits discrete levels of nonlinear dynamical organization in which successive levels are distinguished by local entropy reduction and constraint generation. A system with greater dynamical depth than another consists of a greater number of such nested dynamical levels. Thus, a mechanical or linear thermodynamic system has less dynamical depth than an inorganic self-organized system, which has less dynamical depth than a living system. Including an assessment of dynamical depth can provide a more precise and systematic account of the fundamental difference between inorganic systems (low dynamical depth and living systems (high dynamical depth, irrespective of the number of their parts and the causal relations between them.

Automated technological equipment-robot complexes

International Nuclear Information System (INIS)

Zhitomirskii, S.V.; Samorodskikh, B.L.

1984-01-01

This paper surveys the types of automated technological equipment robot complexes. The principal elements of such complexes are described. Complexes are divided into two principal groups: those using simultaneously acting robots, and those using successively acting robots. The great variety of types of robots using successive action is then described

Managing complex child law

DEFF Research Database (Denmark)

Svendsen, Idamarie Leth

2017-01-01

The article reports the findings of a qualitative study of Danish legal regulation of the public initial assessment of children and young persons and municipal practitioners’ decision-making under this regulation. The regulation mirrors new and complex relations between families and society...... in the form of 7 individual vignette interviews with municipal mid-level managers and professional consultants in five Danish municipalities. The study finds that the regulation is more complex than it looks, and that the complexity is handled through simplifying decision-making patterns that can be seen...

Cyclomatic Complexity: theme and variations

Directory of Open Access Journals (Sweden)

Brian Henderson-Sellers

1993-11-01

Full Text Available Focussing on the "McCabe family" of measures for the decision/logic structure of a program, leads to an evaluation of extensions to modularization, nesting and, potentially, to object-oriented program structures. A comparison of rated, operating and essential complexities of programs suggests two new metrics: "inessential complexity" as a measure of unstructuredness and "product complexity" as a potential objective measure of structural complexity. Finally, nesting and abstraction levels are considered, especially as to how metrics from the "McCabe family" might be applied in an object-oriented systems development environment.

The structure of complex Lie groups

CERN Document Server

Lee, Dong Hoon

2001-01-01

Complex Lie groups have often been used as auxiliaries in the study of real Lie groups in areas such as differential geometry and representation theory. To date, however, no book has fully explored and developed their structural aspects.The Structure of Complex Lie Groups addresses this need. Self-contained, it begins with general concepts introduced via an almost complex structure on a real Lie group. It then moves to the theory of representative functions of Lie groups- used as a primary tool in subsequent chapters-and discusses the extension problem of representations that is essential for studying the structure of complex Lie groups. This is followed by a discourse on complex analytic groups that carry the structure of affine algebraic groups compatible with their analytic group structure. The author then uses the results of his earlier discussions to determine the observability of subgroups of complex Lie groups.The differences between complex algebraic groups and complex Lie groups are sometimes subtle ...

Modeling Complex Systems

CERN Document Server

Boccara, Nino

2010-01-01

Modeling Complex Systems, 2nd Edition, explores the process of modeling complex systems, providing examples from such diverse fields as ecology, epidemiology, sociology, seismology, and economics. It illustrates how models of complex systems are built and provides indispensable mathematical tools for studying their dynamics. This vital introductory text is useful for advanced undergraduate students in various scientific disciplines, and serves as an important reference book for graduate students and young researchers. This enhanced second edition includes: . -recent research results and bibliographic references -extra footnotes which provide biographical information on cited scientists who have made significant contributions to the field -new and improved worked-out examples to aid a student’s comprehension of the content -exercises to challenge the reader and complement the material Nino Boccara is also the author of Essentials of Mathematica: With Applications to Mathematics and Physics (Springer, 2007).

Tensor Product of Polygonal Cell Complexes

OpenAIRE

Chien, Yu-Yen

2017-01-01

We introduce the tensor product of polygonal cell complexes, which interacts nicely with the tensor product of link graphs of complexes. We also develop the unique factorization property of polygonal cell complexes with respect to the tensor product, and study the symmetries of tensor products of polygonal cell complexes.

Organization structures for dealing with complexity

NARCIS (Netherlands)

Meijer, B.R.

2006-01-01

"Complexity is in the eye of the beholder" is a well known quote in the research field of complexity. In the world of managers the word complex is often a synonym for difficult, complicated, involving many factors and highly uncertain. A complex business decision requires careful preparation and

Epidemic modeling in complex realities.

Science.gov (United States)

Colizza, Vittoria; Barthélemy, Marc; Barrat, Alain; Vespignani, Alessandro

2007-04-01

In our global world, the increasing complexity of social relations and transport infrastructures are key factors in the spread of epidemics. In recent years, the increasing availability of computer power has enabled both to obtain reliable data allowing one to quantify the complexity of the networks on which epidemics may propagate and to envision computational tools able to tackle the analysis of such propagation phenomena. These advances have put in evidence the limits of homogeneous assumptions and simple spatial diffusion approaches, and stimulated the inclusion of complex features and heterogeneities relevant in the description of epidemic diffusion. In this paper, we review recent progresses that integrate complex systems and networks analysis with epidemic modelling and focus on the impact of the various complex features of real systems on the dynamics of epidemic spreading.

Provability, complexity, grammars

CERN Document Server

Beklemishev, Lev; Vereshchagin, Nikolai

1999-01-01

The book contains English translations of three outstanding dissertations in mathematical logic and complexity theory. L. Beklemishev proves that all provability logics must belong to one of the four previously known classes. The dissertation of M. Pentus proves the Chomsky conjecture about the equivalence of two approaches to formal languages: the Chomsky hierarchy and the Lambek calculus. The dissertation of N. Vereshchagin describes a general framework for criteria of reversability in complexity theory.

Complexation and molecular modeling studies of europium(III)-gallic acid-amino acid complexes.

Science.gov (United States)

Taha, Mohamed; Khan, Imran; Coutinho, João A P

2016-04-01

With many metal-based drugs extensively used today in the treatment of cancer, attention has focused on the development of new coordination compounds with antitumor activity with europium(III) complexes recently introduced as novel anticancer drugs. The aim of this work is to design new Eu(III) complexes with gallic acid, an antioxida'nt phenolic compound. Gallic acid was chosen because it shows anticancer activity without harming health cells. As antioxidant, it helps to protect human cells against oxidative damage that implicated in DNA damage, cancer, and accelerated cell aging. In this work, the formation of binary and ternary complexes of Eu(III) with gallic acid, primary ligand, and amino acids alanine, leucine, isoleucine, and tryptophan was studied by glass electrode potentiometry in aqueous solution containing 0.1M NaNO3 at (298.2 ± 0.1) K. Their overall stability constants were evaluated and the concentration distributions of the complex species in solution were calculated. The protonation constants of gallic acid and amino acids were also determined at our experimental conditions and compared with those predicted by using conductor-like screening model for realistic solvation (COSMO-RS) model. The geometries of Eu(III)-gallic acid complexes were characterized by the density functional theory (DFT). The spectroscopic UV-visible and photoluminescence measurements are carried out to confirm the formation of Eu(III)-gallic acid complexes in aqueous solutions. Copyright © 2016 Elsevier Inc. All rights reserved.

Complexity factors and prediction of performance

International Nuclear Information System (INIS)

Braarud, Per Oeyvind

1998-03-01

Understanding of what makes a control room situation difficult to handle is important when studying operator performance, both with respect to prediction as well as improvement of the human performance. A factor analytic approach identified eight factors from operators' answers to an 39 item questionnaire about complexity of the operator's task in the control room. A Complexity Profiling Questionnaire was developed, based on the factor analytic results from the operators' conception of complexity. The validity of the identified complexity factors was studied by prediction of crew performance and prediction of plant performance from ratings of the complexity of scenarios. The scenarios were rated by both process experts and the operators participating in the scenarios, using the Complexity Profiling Questionnaire. The process experts' complexity ratings predicted both crew performance and plant performance, while the operators' rating predicted plant performance only. The results reported are from initial studies of complexity, and imply a promising potential for further studies of the concept. The approach used in the study as well as the reported results are discussed. A chapter about the structure of the conception of complexity, and a chapter about further research conclude the report. (author)

Neurosurgical implications of Carney complex.

Science.gov (United States)

Watson, J C; Stratakis, C A; Bryant-Greenwood, P K; Koch, C A; Kirschner, L S; Nguyen, T; Carney, J A; Oldfield, E H

2000-03-01

The authors present their neurosurgical experience with Carney complex. Carney complex, characterized by spotty skin pigmentation, cardiac myxomas, primary pigmented nodular adrenocortical disease, pituitary tumors, and nerve sheath tumors (NSTs), is a recently described, rare, autosomal-dominant familial syndrome that is relatively unknown to neurosurgeons. Neurosurgery is required to treat pituitary adenomas and a rare NST, the psammomatous melanotic schwannoma (PMS), in patients with Carney complex. Cushing's syndrome, a common component of the complex, is caused by primary pigmented nodular adrenocortical disease and is not secondary to an adrenocorticotropic hormone-secreting pituitary adenoma. The authors reviewed 14 cases of Carney complex, five from the literature and nine from their own experience. Of the 14 pituitary adenomas recognized in association with Carney complex, 12 developed growth hormone (GH) hypersecretion (producing gigantism in two patients and acromegaly in 10), and results of immunohistochemical studies in one of the other two were positive for GH. The association of PMSs with Carney complex was established in 1990. Of the reported tumors, 28% were associated with spinal nerve sheaths. The spinal tumors occurred in adults (mean age 32 years, range 18-49 years) who presented with pain and radiculopathy. These NSTs may be malignant (10%) and, as with the cardiac myxomas, are associated with significant rates of morbidity and mortality. Because of the surgical comorbidity associated with cardiac myxoma and/or Cushing's syndrome, recognition of Carney complex has important implications for perisurgical patient management and family screening. Study of the genetics of Carney complex and of the biological abnormalities associated with the tumors may provide insight into the general pathobiological abnormalities associated with the tumors may provide insight into the general pathobiological features of pituitary adenomas and NSTs.

Is dense codeswitching complex?

NARCIS (Netherlands)

Dorleijn, M.

In this paper the question is raised to what extent dense code switching can be considered complex. Psycholinguistic experiments indicate that code switching involves cognitive costs, both in production and comprehension, a conclusion that could indicate that code switching is indeed complex. In

Ternary complex formation at mineral/solution interfaces

International Nuclear Information System (INIS)

Leckie, J.O.

1995-01-01

Adsorption of trace concentrations of radionuclides and heavy metals from aqueous solution is dependent on pH, absorbent and adsorbate concentration, and speciation of the metal in solution. In particular, complexation of metal ions by organic and inorganic ligands can dramatically alter adsorption behavior compared to ligand-free systems. The presence of complexing ligands can cause the formation of ''metal like'' or ''ligand like'' ternary surface complexes depending on whether adsorption of the ternary complex increases or decreases with increasing pH, respectively. Examples of ternary surface complexes behaving ''metal like'' include uranyl-EDTA surface complexes on goethite, neptunyl-EDTA surface complexes on hematite and neptunyl-humic surface complexes on gibbsite. Examples of ''ligand like'' ternary surface complexes include uranyl-carbonato and neptunyl-carbonato surface complexes on iron oxides. The effects of complex solutions and multimineralic systems are discussed. (authors). 39 refs., 16 figs., 8 tabs

Information geometric methods for complexity

Science.gov (United States)

Felice, Domenico; Cafaro, Carlo; Mancini, Stefano

2018-03-01

Research on the use of information geometry (IG) in modern physics has witnessed significant advances recently. In this review article, we report on the utilization of IG methods to define measures of complexity in both classical and, whenever available, quantum physical settings. A paradigmatic example of a dramatic change in complexity is given by phase transitions (PTs). Hence, we review both global and local aspects of PTs described in terms of the scalar curvature of the parameter manifold and the components of the metric tensor, respectively. We also report on the behavior of geodesic paths on the parameter manifold used to gain insight into the dynamics of PTs. Going further, we survey measures of complexity arising in the geometric framework. In particular, we quantify complexity of networks in terms of the Riemannian volume of the parameter space of a statistical manifold associated with a given network. We are also concerned with complexity measures that account for the interactions of a given number of parts of a system that cannot be described in terms of a smaller number of parts of the system. Finally, we investigate complexity measures of entropic motion on curved statistical manifolds that arise from a probabilistic description of physical systems in the presence of limited information. The Kullback-Leibler divergence, the distance to an exponential family and volumes of curved parameter manifolds, are examples of essential IG notions exploited in our discussion of complexity. We conclude by discussing strengths, limits, and possible future applications of IG methods to the physics of complexity.

Dry Distillation of Radioiodine from TeO2 Targets

Directory of Open Access Journals (Sweden)

Jacek Koziorowski

2013-10-01

Full Text Available As medical cyclotrons are becoming more abundant, 123I and 124I are getting more attention as alternatives to 131I for diagnostics of thyroid disease. Both 123I and 124I provide better diagnostics, deliver less dose to patients and both reduce the risk of thyroid stunning, facilitating subsequent therapy. Dry distillation of radioiodine from tellurium dioxide targets has become the standard approach to producing these radioiodines. Setting up such a production of radioiodine is associated with a lengthy optimization of the process and for this purpose natural tellurium is often used for economical reasons. In this paper, the distillation parameters are scrutinized to ensure optimal distillation temperature, in order to minimize time spent and prevent loss of expensive target material. It is further demonstrated how the individual iodine isotopes, produced from proton bombardment of natTe, will diffuse out of the target in a time dependent ratio. We believe the effect is due to the isotopes having their maximum cross section at different energies. The individual isotopes produced will thus have their highest concentration at different depths in the target. This results in individual mean diffusion lengths and diffusion times for the different isotopes.