Analysis of tellurium thin films electrodeposition from acidic citric bath

Energy Technology Data Exchange (ETDEWEB)

Kowalik, Remigiusz; Kutyła, Dawid [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland); Mech, Krzysztof [AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, al. A. Mickiewicza 30, Krakow (Poland); Żabiński, Piotr, E-mail: rkowalik@agh.edu.pl [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, al. A. Mickiewicza 30, 30-059 Krakow (Poland)

2016-12-01

This work presents the description of the electrochemical process of formation thin tellurium layers from citrate acidic solution. The suggested methodology consists in the preparation of stable acidic baths with high content of tellurium, and with the addition of citrate acid. In order to analyse the mechanism of the process of tellurium deposition, the electroanalytical tests were conducted. The tests of cyclic voltammetry and hydrodynamic ones were performed with the use of polycrystalline gold disk electrode. The range of potentials in which deposition of tellurium in direct four-electron process is possible was determined as well as the reduction of deposited Te° to Te{sup 2−} and its re-deposition as a result of the comproportionation reaction. On the basis of the obtained results, the deposition of tellurium was conducted by the potentiostatic method. The influence of a deposition potential and a concentration of TeO{sub 2} in the solution on the rate of tellurium coatings deposition was examined. The presence of tellurium was confirmed by X-ray spectrofluorometry and electron probe microanalysis. In order to determine the phase composition and the morphology, the obtained coatings were analysed with the use of x-ray diffraction and scanning electron microscopy.

Properties of low-alloy steel with tellurium

International Nuclear Information System (INIS)

Popova, L.V.; Lebedev, D.V.; Litvinenko, D.A.; Nasibov, A.G.

1983-01-01

The results of investigations into 09G2 and 09G2F steels alloyed with tellurium after controlled rolling are presented. 0.002-0.011% tellurium additions did not change strength and plastic properties of the steels after controlled rolling. Tellurium additions results in 40-50% increase of the steel impact strength on samples With circular and sharp cuts in brittle-viscous region. 0.002-0.003% of tellurium is considered to be the optimum content from the view point of increa=. sing steel strength. Increase of impact strength takes place at the expense of growth of both work function of crack formation and work function of crack propagation but in different temperature ranges: at the expense of firstone at 80-40 deg C, at the expense of second one at 20-40 deg C. 0.002-0.011% teilurium additions mainly at the expense of sulphide globularization bring about decrease of anisotropy of steet properties by impact strength reducing anisotropy factor from 2 to 1.5

Analysis of tellurium-silicon alloys. Part 1. Determination of tellurium by the reduction from perchloric acid solution

International Nuclear Information System (INIS)

Teperek, J.

1977-01-01

When 100-150 mg of tellurium is dissolved in the solution containing 20 cm 3 72 wt.% of perchloric acid, the reduction of tellurium to elementary form is possible only after adding 60-100 milimoles of HCl. The reduction is performed by adding 1 cm 3 of saturated sodium pyrosulphite solution (Na 2 S 2 O 5 ) and 10 cm 3 of 10 wt.% hydrazine hydrochloride solution (N 2 H 4 .2HCl) to 80-90 cm 3 of cold solution of Te in HClO 4 -HCl mixture. The reduction is completed after 3-5 min. of boiling. When 150-200 mg sample of Te-Si alloy is dissolved in 20 cm 3 of hot 72% per chloric acid, the separation of components is reached. Tellurium can be determinated in filtrate by proposed procedure with high accuracy and precision. (author)

Polarographic determination of selenium and tellurium in silver-gold alloys

International Nuclear Information System (INIS)

Gornostaeva, T.D.; Shmargun, S.V.

1986-01-01

The determination of selenium and tellurium is of importance in monitoring the composition of silver-gold alloys (SGA) since these elements are harmful impurities in the pure metals. Tellurium is determined in silver alloys by atomic absorption and atomic emmission methods; selenium determination is made by atomic absorption methods. This paper examines the polarographic determination of silver and tellurium in SGA containing platinum metals and copper. Copper and the bulk of the platinum and palladium were removed by precipitating selenium and tellurium with potassium hypophosphite in the elementary state from 6 M HC1. The results of an analysis of samples of SGA according to the proposed method were compared with the results obtained by the atomic absorption method. the relative deviation in the determination of 0.02-1.0% by weight selenium and tellurium does not exceed 0.12 (n = 5)

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

Energy Technology Data Exchange (ETDEWEB)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of); Shakibaie, Mojtaba [Department of Pharmacognosy and Biotechnology, School of Pharmacy, Pharmaceutics Research Center, Kerman University of Medical Sciences, P.O. Box 76175-493 Kerman (Iran, Islamic Republic of); Rezaie, Sassan [Department of Medical Biotechnology, School of Advanced Medical Technologies, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Shahverdi, Ahmad Reza, E-mail: shahverd@sina.tums.ac.ir [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of)

2012-11-15

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

International Nuclear Information System (INIS)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham; Shakibaie, Mojtaba; Rezaie, Sassan; Shahverdi, Ahmad Reza

2012-01-01

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Structure and activity of tellurium-cerium oxide acrylonitrile catalysts

International Nuclear Information System (INIS)

Bart, J.C.J.; Giordano, N.

1982-01-01

Ammoxidation of propylene to acrylonitrile (ACN) was investigated over various silica-supported (Te,Ce)O catalysts at 360 and 440 0 C. The binary oxide system used consists of a single nonstoichiometric fluorite-type phase α-(Ce,Te)O 2 up to about 80 mole% TeO 2 and a tellurium-saturated solid solution β-(Ce,Te)O 2 at higher tellurium concentrations. The ACN yield varies almost linearly with the tellurium content of (Ce,Te)O 2 . The β-(Ce,Te)O 2 phase is the most active component of the system (propylene conversion and ACN selectivity at 440 C of 76.7 and 74%, respectively) and is slightly more selective to ACN than α-Te0 2 . Tellurium reduces the overoxidation properties of cerium and selective oxidation occurs through Te(IV)-bonded oxygen

A recycling model of the biokinetics of systemic tellurium.

Science.gov (United States)

Giussani, Augusto

2014-11-01

To develop a compartmental model of the systemic biokinetics of tellurium required for calculating the internal dose and interpreting bioassay measurements after incorporation of radioactive tellurium. The compartmental model for tellurium was developed with the software SAAM II v. 2.0 (©The Epsilon Group, Charlottesville, Virginia, USA). Model parameters were determined on the basis of published retention and excretion data in humans and animals. The model consists of two blood compartments, one compartment each for liver, kidneys, thyroid, four compartments for bone tissues and a generic compartment for the soft tissues. The model predicts a rapid urinary excretion of systemic tellurium: 45% in the first 24 h and 84% after 50 d. Faecal excretion amounts to 0.4% after 3 d and 9% after 50 d. Whole body retention is 55% after one day, and 2.8% after 100 d. These values as well as the retained fractions in the single organs are reasonably consistent with the available human and animal data (studies with swine and guinea pigs). The proposed model gives a realistic description of the available biokinetic data for tellurium and will be adopted by the International Commission on Radiological Protection for applications in internal dosimetry.

Atomic absorption determination of ultratrace tellurium in rocks utilizing high sensitivity sampling systems

International Nuclear Information System (INIS)

Beaty, R.D.

1973-01-01

The sampling boat and the graphite furnace were shown to possess the required sensitivity to detect tellurium at ultratrace levels, in a variety of sample types, by atomic absorption. In the sampling boat approach, tellurium in sample solutions is chemically separated and concentrated by extraction into methyl isobutyl ketone before measurement. For samples exhibiting extraction interferences or excessively high background absorption, a preliminary separation of tellurium by coprecipitation with selenium is described. Using this technique, tellurium can be quantitatively detected down to 5 nanograms and linear response is observed to 100 nanograms. Relative standard deviations of better than 7 percent are achieved for 50 nanograms of tellurium. For samples that have a tellurium content below the detection limits of the sampling boat, the graphite furnace is used for atomization. By this method, as little as 0.07 nanograms of tellurium can be detected, and a precision of 1 percent relative standard deviation is achievable at the 5 nanogram level. A routinely applicable procedure was developed for determining tellurium in rocks, using the graphite furnace, after a hydrofluoric acid decomposition of the sample. Using this procedure, tellurium data were obtained on 20 different rocks, and the significance of this new information is discussed. (Diss. Abstr. Int., B)

METHODS OF SYNTHESIS EIGHT-TELLURIUM-CONTAINING HETEROCYCLES WITH MORE HETEROATOMS

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2013-01-01

Full Text Available In this article systematized and summarized data on the synthesis of neweight-embered tellurium-containing heterocycles and new preparative methods described above produce heterocyclic tellurium.

Inclusion free cadmium zinc tellurium and cadmium tellurium crystals and associated growth method

Science.gov (United States)

Bolotnikov, Aleskey E [South Setauket, NY; James, Ralph B [Ridge, NY

2010-07-20

The present disclosure provides systems and methods for crystal growth of cadmium zinc tellurium (CZT) and cadmium tellurium (CdTe) crystals with an inverted growth reactor chamber. The inverted growth reactor chamber enables growth of single, large, high purity CZT and CdTe crystals that can be used, for example, in X-ray and gamma detection, substrates for infrared detectors, or the like. The inverted growth reactor chamber enables reductions in the presence of Te inclusions, which are recognized as an important limiting factor in using CZT or CdTe as radiation detectors. The inverted growth reactor chamber can be utilized with existing crystal growth techniques such as the Bridgman crystal growth mechanism and the like. In an exemplary embodiment, the inverted growth reactor chamber is a U-shaped ampoule.

Selenium and tellurium reagents in organic synthesis

International Nuclear Information System (INIS)

Comasseto, J.V.

1984-01-01

A review of the contribution of the University of Sao Paulo (SP, Brazil) to the organic synthesis of selenium and tellurium reagents is made. Major reactions amoung selenium compounds and insaturated substrates, phosphorus, ester enolates as well as the use of phase transference catalysed reactions to produce arylselenolate are described. For tellurium, interactions of its compounds with organic substrates and reactive intermediates (e.g. benzino diazomethane) are reported. (C.L.B.) [pt

Rapid radiochemical ion-exchange separation of iodine from tellurium: a novel radioiodine-132 generator

Energy Technology Data Exchange (ETDEWEB)

Abrao, A

1975-01-01

Tellurium ions form a soluble cationic complex with thiourea in acid medium. The cationic tellurium-thiourea species is strongly absorbed on a cationic ion exchanger. The retention of tellurium on the resin enables many interesting separation schemes for tellurium from various ions. With special interest, the separation of iodine from tellurium was studied. An efficient and convenient iodine-132 generator is described, in which the radio-iodine is eluted with water or 9 g/1 NaCl, when desired.

Electrophilic addition of selenium and tellurium halides to methyldiethynylsilane

International Nuclear Information System (INIS)

Amosova, S.V.; Penzik, M.V.; Martynov, A.V.; Zhilitskaya, L.V.; Voronkov, M.G.

2009-01-01

Reaction of TeCl 4 with methyldiethynylsilane (MDES) proceeds with the predominant formation of E-isomer 1,1,3,6-tetrachlorine-1-methyl-1-(methyldiethynylsiloxy)-1,4-tellurium(IV) silafulvic due to the interaction of intermediate E-isomer 4-methyl-1,1,3,6-tetrachlorine-1,4-tellurium(IV)silafulvic with MDES. TeCl 4 Reacts with MDES without reduction of Te(IV) in Te(II). Tetracoordination of tellurium atom in heterocycle was established by NMR 125 Te. Mass spectrum of heterocycle shows the presence of fragmentary ions [M-Cl 2 ] + . According elemental analysis Te:Cl=1:4 ratio proves composition of heterocycle

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis

Directory of Open Access Journals (Sweden)

Yang F

2014-10-01

Full Text Available Fang Yang,1 Ka-Hing Wong,2 Yufeng Yang,3 Xiaoling Li,1 Jie Jiang,1 Wenjie Zheng,1 Hualian Wu,1 Tianfeng Chen1 1Department of Chemistry, Jinan University, Guangzhou, People’s Republic of China; 2Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hong Kong, People’s Republic of China; 3Institute of Hydrobiology, College of Life Science and Technology, Jinan University, Guangzhou, People’s Republic of China Abstract: Tellurium-containing phycocyanin (Te-PC and allophycocyanin (Te-APC, two organic tellurium (Te species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 µg g-1 protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropanedihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress. Keywords: tellurium, phycocyanin, allophycocyanin, purification, antioxidant activity

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis.

Science.gov (United States)

Yang, Fang; Wong, Ka-Hing; Yang, Yufeng; Li, Xiaoling; Jiang, Jie; Zheng, Wenjie; Wu, Hualian; Chen, Tianfeng

2014-01-01

Tellurium-containing phycocyanin (Te-PC) and allophycocyanin (Te-APC), two organic tellurium (Te) species, were purified from tellurium-enriched Spirulina platensis by a fast protein liquid chromatographic method. It was found that the incorporation of Te into the peptides enhanced the antioxidant activities of both phycobiliproteins. With fractionation by ammonium sulfate precipitation and hydroxylapatite chromatography, Te-PC and Te-APC could be effectively separated with high purity, and Te concentrations were 611.1 and 625.3 μg g(-1) protein in Te-PC and Te-APC, respectively. The subunits in the proteins were identified by using MALDI-TOF-TOF mass spectrometry. Te incorporation enhanced the antioxidant activities of both phycobiliproteins, as examined by 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid assay. Moreover, Te-PC and Te-APC showed dose-dependent protection on erythrocytes against the water-soluble free radical initiator 2,2'-azo(2-asmidinopropane)dihydrochloride-induced hemolysis. In the hepatoprotective model, apoptotic cell death and nuclear condensation induced by tert-butyl hydroperoxide in HepG2 cells was significantly attenuated by Te-PC and Te-APC. Taken together, these results suggest that Te-PC and Te-APC are promising Te-containing proteins with application potential for treatment of diseases related to oxidative stress.

Flame and flameless atomic-absorption determination of tellurium in geological materials

Science.gov (United States)

Chao, T.T.; Sanzolone, R.F.; Hubert, A.E.

1978-01-01

The sample is digested with a solution of hydrobromic acid and bromine and the excess of bromine is expelled. After dilution of the solution to approximately 3 M in hydrobromic acid, ascorbic acid is added to reduce iron(III) before extraction of tellurium into methyl isobutyl ketone (MIBK). An oxidizing air-acetylene flame is used to determine tellurium in the 0.1-20 ppm range. For samples containing 4-200 ppb of tellurium, a carbon-rod atomizer is used after the MIBK extract has been washed with 0.5 M hydrobromic acid to remove the residual iron. The flame procedure is useful for rapid preliminary monitoring, and the flameless procedure can determine tellurium at very low concentrations. ?? 1978.

A rapid radiochemical ion-exchange separation of iodine from tellurium: a novel radioiodine-132 generator

International Nuclear Information System (INIS)

Abrao, A.

1975-01-01

Tellurium ions form a soluble cationic complex with thiourea in acid medium. The cationic tellurium-thiourea species is strongly absorbed on a cationic ion exchanger. The retention of tellurium on the resin enables many interesting separation schemes for tellurium from various ions. With special interest, the separation of iodine from tellurium was studied. An efficient and convenient iodine-132 generator is described, in which the radio-iodine is eluted with water or 9 g/1 NaCL, when desired

Study of distribution coefficients of admixtures in tellurium

International Nuclear Information System (INIS)

Kuchar, L.; Drapala, J.; Kuchar, L. jr.

1986-01-01

Limit areas of tellurium-admixture binary systems were studied and the values determined of steady-state distribution coefficients of admixtures. A second order polynomial was used to express equations of solidus and liquidus curves for Te-Se, Te-S, Te-Hg systems; the curves are graphically represented. The most effective method for preparing high-purity tellurium is zonal melting with material removal. (M.D.). 4 figs., 4 tabs., 16 refs

Effects of tellurium concentration on the structure of melt-grown ZnSe crystals

International Nuclear Information System (INIS)

Atroshchenko, Lyubov V.; Galkin, Sergey N.; Rybalka, Irina A.; Voronkin, Evgeniy F.; Lalayants, Alexandr I.; Ryzhikov, Vladimir D.; Fedorov, Alexandr G.

2005-01-01

It has been shown that isovalent doping by tellurium positively affects the structural perfection of ZnSe crystals related to the completeness of the wurtzite-sphalerite phase transition. The optimum concentration range of tellurium in ZnSe crystals is 0.3-0.6 mass %. X-ray diffraction studies have shown that in ZnSe 1-x Te x crystals at tellurium concentrations below 0.3 mass % twinning and packing defects occur, while tellurium concentrations above 0.6 mass % lead to formation of tetragonal crystal lattice

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2003-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122 Te, 124 Te, 125 Te, 126 Te, 128 Te, and 130 Te are reported. These values are based on a combination of newly determined partial γ-ray cross sections obtained from experiments on targets contained natural Te and γ intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

International Nuclear Information System (INIS)

Tomandl, I.; Honzatko, J.; Egidy, T. von; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-01-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given

Thermal neutron capture cross sections of tellurium isotopes

Energy Technology Data Exchange (ETDEWEB)

Tomandl, I.; Honzatko, J.; von Egidy, T.; Wirth, H.-F.; Belgya, T.; Lakatos, M.; Szentmiklosi, L.; Revay, Zs.; Molnar, G.L.; Firestone, R.B.; Bondarenko, V.

2004-03-01

New values for thermal neutron capture cross sections of the tellurium isotopes 122Te, 124Te, 125Te, 126Te, 128Te, and 130Te are reported. These values are based on a combination of newly determined partial g-ray cross sections obtained from experiments on targets contained natural Te and gamma intensities per capture of individual Te isotopes. Isomeric ratios for the thermal neutron capture on the even tellurium isotopes are also given.

Van der Waals epitaxy and photoresponse of hexagonal tellurium nanoplates on flexible mica sheets.

Science.gov (United States)

Wang, Qisheng; Safdar, Muhammad; Xu, Kai; Mirza, Misbah; Wang, Zhenxing; He, Jun

2014-07-22

Van der Waals epitaxy (vdWE) is of great interest due to its extensive applications in the synthesis of ultrathin two-dimensional (2D) layered materials. However, vdWE of nonlayered functional materials is still not very well documented. Here, although tellurium has a strong tendency to grow into one-dimensional nanoarchitecture due to its chain-like structure, we successfully realize 2D hexagonal tellurium nanoplates on flexible mica sheets via vdWE. Chemically inert mica surface is found to be crucial for the lateral growth of hexagonal tellurium nanoplates since it (1) facilitates the migration of tellurium adatoms along mica surface and (2) allows a large lattice mismatch. Furthermore, 2D tellurium hexagonal nanoplates-based photodetectors are in situ fabricated on flexible mica sheets. Efficient photoresponse is obtained even after bending the device for 100 times, indicating 2D tellurium hexagonal nanoplates-based photodetectors on mica sheets have a great application potential in flexible and wearable optoelectronic devices. We believe the fundamental understanding of vdWE effect on the growth of 2D tellurium hexagonal nanoplate can pave the way toward leveraging vdWE as a useful channel to realize the 2D geometry of other nonlayered materials.

Investigation of γ-irradiation influence on the DLTS spectra in silicon diluted by tellurium

International Nuclear Information System (INIS)

Sultanov, N.A.; Tadzhibaev, M.; Mirzabadalov, Zh

1997-01-01

The influence of gamma-radiation on deep level transient spectroscopy(DLTS) spectra for silicon crystals doped with tellurium was studied. The DLTS spectra have shown that tellurium in silicon formed two deep levels with fixed ionization energy. It was shown that the presence of tellurium prevents the formation of radiation defects

Status of tellurium--hastelloy N studies in molten fluoride salts

International Nuclear Information System (INIS)

Keiser, J.R.

1977-10-01

Tellurium, which is a fission product in nuclear reactor fuels, can embrittle the surface grain boundaries of nickel-base structural materials. This report summarizes results of an experimental investigation conducted to understand the mechanism and to develop a means of controlling this embrittlement in the alloy Hastelloy N. The addition of a chromium telluride to salt can be used to provide small partial pressures of tellurium simulating a reactor environment where tellurium appears as a fission product. The intergranular embrittlement produced in Hastelloy N when exposed to this chromium telluride-salt mixture can be reduced by adding niobium to the Hastelloy N or by controlling the oxidation potential of the salt in the reducing range

Comparison between selenium and tellurium clusters

International Nuclear Information System (INIS)

Benamar, A.; Rayane, D.; Tribollet, B.; Broyer, M.; Melinon, P.

1991-01-01

Selenium and tellurium clusters are produced by the inert gas condensation technique. The mass spectra of both species are completely different and reveal different properties. In selenium, a periodicity of 6-7 is observed and may be interpreted by the binding energy between small cyclic molecules. Moreover, it was very difficult to obtained large clusters probably because the binding energy between these molecules is very small. In tellurium, these periodic structures do not exist and large clusters are easily obtained in nucleation conditions where only small selenium clusters are present. These results are discussed and a simple nucleation model is used to illustrate this different behavior. Finally these clusters properties are correlated to the bulk structure of both materials. (orig.)

Electrodeposition of antimony, tellurium and their alloys from molten acetamide mixtures

NARCIS (Netherlands)

Nguyen, H.P.; Peng, X.; Murugan, G.; Vullers, R.J.M.; Vereecken, P.M.; Fransaer, J.

2013-01-01

We examine the electrodeposition of antimony (Sb), tellurium (Te) and their alloys from molten mixtures of acetamide - antimony chloride and tellurium chloride. The binary mixtures of acetamide with SbCl3 and TeCl 4 exhibit eutectic formation with large depressions of freezing points to below room

Neutron activation analysis of high purity tellurium

International Nuclear Information System (INIS)

Gil'bert, Eh.N.; Verevkin, G.V.; Obrazovskij, E.G.; Shatskaya, S.S.

1980-01-01

A scheme of neutron activation analysis of high purity tellurium is developed. Weighed amount of Te (0.5 g) is irradiated for 20-40 hr in the flux of 2x10 13 neutron/(cm 2 xs). After decomposition of the sample impurities of gold and palladium are determined by the extraction with organic sulphides. Tellurium separation from the remaining impurities is carried out by the extraction with monothiobenzoic acid from weakly acidic HCl solutions in the presence of iodide-ions, suppressing silver extraction. Remaining impurity elements in the refined product are determined γ-spectrometrically. The method allows to determine 34 impurities with determination limits 10 -6 -10 -11 g

The defects produced by electron irradiation in tellurium-doped germanium

International Nuclear Information System (INIS)

Fukuoka, Noboru; Saito, Haruo

1989-01-01

The nature of the irradiation induced defects in a germanium single crystal doped with tellurium was studied by DLTS and electrical measurements. The E c -0.21 eV level produced by irradiation with 1.5 MeV electrons was studied using the DLTS technique. It was found that the defect associated with this level is a divacancy. The E-center like defect (group V impurity-vacancy pair) introduces the E c -0.20 eV level in samples doped with a group V impurity. The level introduced by a tellurium (group VI impurity)-vacancy pair is deeper. The E c -0.16 eV level was generated by annealing at 430 K. A tellurium-vacancies complex is proposed as the defect associated with this level. (author)

DETECTION OF THE SECOND r-PROCESS PEAK ELEMENT TELLURIUM IN METAL-POOR STARS ,

International Nuclear Information System (INIS)

Roederer, Ian U.; Lawler, James E.; Cowan, John J.; Beers, Timothy C.; Frebel, Anna; Ivans, Inese I.; Schatz, Hendrik; Sobeck, Jennifer S.; Sneden, Christopher

2012-01-01

Using near-ultraviolet spectra obtained with the Space Telescope Imaging Spectrograph on board the Hubble Space Telescope, we detect neutral tellurium in three metal-poor stars enriched by products of r-process nucleosynthesis, BD +17 3248, HD 108317, and HD 128279. Tellurium (Te, Z = 52) is found at the second r-process peak (A ≈ 130) associated with the N = 82 neutron shell closure, and it has not been detected previously in Galactic halo stars. The derived tellurium abundances match the scaled solar system r-process distribution within the uncertainties, confirming the predicted second peak r-process residuals. These results suggest that tellurium is predominantly produced in the main component of the r-process, along with the rare earth elements.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2 and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

K. L. Vialetti

2008-05-20

This report presents the final hazard categorization for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

International Nuclear Information System (INIS)

Rodovsky, T.J.

2006-01-01

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2006-12-06

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2007-04-12

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

International Nuclear Information System (INIS)

TRodovsky, T.J.

2007-01-01

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site

Review of tellurium release rates from LWR fuel elements under accident conditions

International Nuclear Information System (INIS)

Lorenz, R.A.; Beahm, E.C.; Wichner, R.P.

1983-01-01

Although fission product tellurium presents a potentially significant radiohazard, its release and transport in source-term experiments is frequently overlooked because it does not possess a readily measurable, gamma emission; moreover, a recent study emphasized noble gas, iodine and cesium release from LWR fuel elements because of the large data base that exists for these materials. Some new tests show that in some cases tellurium may be held up in core material to a greater degree than previously assumed - an observation that prompts a careful reappraisal of the existing tellurium-release data and its chemical foundation

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

J.D. Ludowise

2009-06-17

This report presents the final hazard categorization for the remediation of the 118-D-1, 118-D-2, 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site. A material at risk calculation was performed that determined the radiological inventory for each burial ground to be Hazard Category 3.

Optimization of scintillator loading with the tellurium-130 isotope for long-term stability

Science.gov (United States)

Duhamel, Lauren; Song, Xiaoya; Goutnik, Michael; Kaptanoglu, Tanner; Klein, Joshua; SNO+ Collaboration

2017-09-01

Tellurium-130 was selected as the isotope for the SNO + neutrinoless double beta decay search, as 130Te decays to 130Xe via double beta decay. Linear alkyl benzene(LAB) is the liquid scintillator for the SNO + experiment. To load tellurium into scintillator, it is combined with 1,2-butanediol to form an organometallic complex, commonly called tellurium butanediol (TeBD). This study focuses on maximizing the percentage of tellurium loaded into scintillator and evaluates the complex's long-term stability. Studies on the effect of nucleation due to imperfections in the detector's surface and external particulates were employed by filtration and induced nucleation. The impact of water on the stability of TeBD complex was evaluated by liquid-nitrogen sparging, variability in pH and induced humidity. Alternative loading methods were evaluated, including the addition of stability-inducing organic compounds. Samples of tellurium-loaded scintillator were synthesized, treated, and consistently monitored in a controlled environment. It was found that the hydronium ions cause precipitation in the loaded scintillator, demonstrating that water has a detrimental effect on long-term stability. Optimization of loaded scintillator stability can contribute to the SNO + double beta decay search.

Methods of selenium and tellurium determination in geological and enviromental materials

International Nuclear Information System (INIS)

Nazarenko, I.I.; Kislova, I.V.

1988-01-01

Atomic-absorption and atomic-emission methods of tellurium determination in ores and products of their processing are described. Flame variant with extractional concentration permits to determine tellurium with the concentration up to 6x10 -6 %, the use of graphite cuvette after preliminary concentration-up to 1x10 -6 %. Atomic-emissional method permits to determine 3x10 -4 % Te from sample of 0.5 g

Selenium and tellurium as carbon substitutes

International Nuclear Information System (INIS)

Knapp, F.F. Jr.

1980-01-01

This review has summarized structure-activity studies with 75 Se- and /sup 123m/Te-labeled radiopharmaceuticals in which the selenium or tellurium heteroatom has been inserted between carbon-carbon bonds. The agents that have been investigated in most detail include steroids for adrenal imaging and long-chain fatty acids, and a variety of other unique agents have also been studied. Because of the great versatility of the organic chemistry of selenium and tellurium, there is continuing interest in the preparation of radiopharmaceuticals labeled with 75 Se, 73 Se, and /sup 123m/Te. There are two important factors which will determine the extent of future interest in such agents. These include the necessity of a decrease in the cost of highly enriched 122 Te to make the reactor production of /sup 123m/Te cost effective. In addition, the potential preparation of large amounts of 73 Se should stimulate the development of 73 Se-labeled radiopharmaceuticals

Final Hazard Categorization and Auditable Safety Analysis for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2 and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2006-03-01

This report presents the initial hazard categorization, final hazard categorization and auditable safety analysis for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Selective floatation-spectrophotometric determination of tellurium (4) with papaverine and butyl rhodamine B

International Nuclear Information System (INIS)

Skripchuk, V.G.

1981-01-01

It is shown, that papaverine reacts with a bromide complex of tellurium (4) to form a compound readily floated by toluene. The floatation is carried out from an aqueous solution, 5.2 M in H 2 SO 4 , 0.2 M in KBr and 5.4x10 -3 M in papaverine. The absorbance is a function of tellurium (4) concentration over a range of 5-100 μg Te/5 ml. Such a highly sensitive reagent as butylrhodamine B can be effectively substituted for papaverine. The floatation results in better selectivity. The method makes it possible to determine tellurium in blister, anodic and cathodic copper without matrix preseparation [ru

Investigation of biomethylation of arsenic and tellurium during composting

International Nuclear Information System (INIS)

Diaz-Bone, Roland A.; Raabe, Maren; Awissus, Simone; Keuter, Bianca; Menzel, Bernd; Kueppers, Klaus; Widmann, Renatus; Hirner, Alfred V.

2011-01-01

Though the process of composting features a high microbiological activity, its potential to methylate metals and metalloids has been little investigated so far in spite of the high impact of this process on metal(loid) toxicity and mobility. Here, we studied the biotransformation of arsenic, tellurium, antimony, tin and germanium during composting. Time resolved investigation revealed a highly dynamic process during self-heated composting with markedly differing time patterns for arsenic and tellurium species. Extraordinary high concentrations of up to 150 mg kg -1 methylated arsenic species as well as conversion rates up to 50% for arsenic and 5% for tellurium were observed. In contrast, little to no conversion was observed for antimony, tin and germanium. In addition to experiments with metal(loid) salts, composting of arsenic hyperaccumulating ferns Pteris vittata and P. cretica grown on As-amended soils was studied. Arsenic accumulated in the fronds was efficiently methylated resulting in up to 8 mg kg -1 methylated arsenic species. Overall, these studies indicate that metal(loid)s can undergo intensive biomethylation during composting. Due to the high mobility of methylated species this process needs to be considered in organic waste treatment of metal(loid) contaminated waste materials.

Determining arsenic in elemental antimony containing selenium and tellurium

International Nuclear Information System (INIS)

Mogileva, M.G.; Kozlova, E.L.

1986-01-01

The authors have developed a method of determining arsenic in metallic antimony containing selenium, tellurium, and mercury, in which they isolated it in elementary form for separation from the antimony and the associated elements (silicon and phosphorus), followed by colorimetric determination of the arsenic from arsenic-molbdenum blue. The reducing agents to reduce the arsenic were sodium hypophosphite and tin(II) chloride, which do not reduce antimony and which do not interfere with the determination. This method of determining arsenic in metallic antimony without preliminary separation of the selenium and tellurium is in no way inferior in accuracy to the method given in All-Union State Standard (GOST) 1367.4-83

Release of tellurium and cesium from UO2 in LWR fuel rods during irradiation

International Nuclear Information System (INIS)

Malen, K.A.

1983-01-01

In this paper the release of tellurium (Te-132) and cesium (Cs-134 and Cs-137) from UO 2 -fuel is analyzed. The basis for the analysis is the experimental results from the S176 series of experiments performed at Studsvik. It seems that the model developed earlier for release of iodine applies also to tellurium and cesium. This model assumes sweeping up of the species in question by moving grain boundaries and subsequent release through grain boundary porosity. An interesting extra feature is deposition of tellurium at temperatures in the range 1500-2000 K believed to be due to condensation. (author)

METALCOMPLEXES OF TELLURIUM-CONTAINING AMINES AND AZOMETINES

Directory of Open Access Journals (Sweden)

G. M. Abakarov

2014-01-01

Full Text Available In this article methods of synthesis and reactionary ability of metalcomplexes of tellurium-containing amines, azometines, of a problem of competitive coordination with use of the principle of "soft" and "rigid" acids and the bases (R. Pearson.

The characterisation of vapour-phase alkali metal-tellurium-oxygen species

International Nuclear Information System (INIS)

Gomme, R.A.; Ogden, J.S.; Bowsher, B.R.

1986-10-01

Detailed assessments of hypothetical severe accidents in light water reactors require the identification of the chemical forms of the radionuclides in order to determine their transport characteristics. Caesium and tellurium are important volatile fission products in accident scenarios. This report describes detailed studies to characterise the chemical species that vaporise from heated mixtures of various alkali metal-tellurium-oxygen systems. The molecular species were characterised by a combination of quadrupole mass spectrometry and matrix isolation-infrared spectroscopy undertaken in conjunction with experiments involving oxygen-18 substitution. The resulting spectra were interpreted in terms of a vapour-phase molecule with the stoichiometry M 2 TeO 3 (M = K,Rb,Cs) for M/Te molecular ratios of ∼ 2, and polymeric species for ratios < 2. This work has demonstrated the stability of caesium tellurite. The formation of this relatively low-volatility, water-soluble species could significantly modify the transport and release of caesium and tellurium. The data presented in this report should allow more comprehensive thermodynamic calculations to be undertaken that assist in the quantification of fission product behaviour during severe reactor accidents. (author)

Double beta decay of tellurium-130

International Nuclear Information System (INIS)

Richardson, J.F.; Manuel, O.K.; Sinha, B.; Thorpe, R.I.

1986-01-01

The isotopic composition of xenon is reported in four, neutron-irradiated tellurium minerals - tellurobismuthite from Boliden, Sweden, native tellurium from the Good Hope Mine of Gunnison County, Colorado, altaite from the Kirkland Lake area, Ontario, and altaite from the Mattagami Lake area, Quebec. From the amount of radiogenic 130 Xe and pile-produced 131 Xe in these samples, it is concluded that the half-life of 130 Te for ββ-decay is 21 y based on measured values of (1.0+-0.3) . 10 21 y and higher. Our results demonstrate that there has been no significant partial leakage of radiogenic 130 Xe from these minerals over geologic time. Larger values of Tsub(1/2), as indicated from some of the analysis reported here and in other studies, are attributed to recrystallization of the soft telluride minerals and complete resetting of the Te-Xe system after mineralization. The value obtained here for the half-life of 130 Te is substantiated by recent measurements on xenon in tellurides from Kalgoorlie, Western Australia. (orig.)

Sulfur, selenium, tellurium and polonium

International Nuclear Information System (INIS)

Berry, F.J.

1987-01-01

This chapter on the coordination compounds of sulfur, selenium, tellurium and polonium starts with an introduction to the bonding, valence and geometry of the elements. Complexes of the group VIB elements are discussed with particular reference to the halo and pseudohalide complexes, oxo acid complexes, oxygen and nitrogen donor complexes and sulfur and selenium donor complexes. There is a section on the biological properties of the complexes discussed. (UK)

RILIS-ionized mercury and tellurium beams at ISOLDE CERN

Energy Technology Data Exchange (ETDEWEB)

Day Goodacre, T., E-mail: thomas.day.goodacre@cern.ch [CERN (Switzerland); Billowes, J. [The University of Manchester, School of Physics and Astronomy (United Kingdom); Chrysalidis, K. [CERN (Switzerland); Fedorov, D. V. [Petersburg Nuclear Physics Institute (Russian Federation); Fedosseev, V. N.; Marsh, B. A. [CERN (Switzerland); Molkanov, P. L. [Petersburg Nuclear Physics Institute (Russian Federation); Rossel, R. E.; Rothe, S.; Seiffert, C. [CERN (Switzerland); Wendt, K. D. A. [Johannes Gutenberg Universität, Institut für Physik (Germany)

2017-11-15

This paper presents the results of ionization scheme development for application at the ISOLDE Resonance Ionization Laser Ion Source (RILIS). Two new ionization schemes for mercury are presented: a three-step three-resonance ionization scheme, ionizing via an excitation to a Rydberg level and a three-step two-resonance ionization scheme, with a non-resonant final step to the ionization continuum that corresponded to a factor of four higher ionization efficiency. The efficiency of the optimal mercury ionization scheme was measured, together with the efficiency of a new three-step three resonance ionization scheme for tellurium. The efficiencies of the mercury and tellurium ionization schemes were determined to be 6 % and >18 % respectively.

Nano-Structured Crystalline Te Films by Laser Gas-Phase Pyrolysis of Dimethyl Tellurium

Czech Academy of Sciences Publication Activity Database

Pola, Josef; Pokorná, Veronika; Boháček, Jaroslav; Bastl, Zdeněk; Ouchi, A.

2004-01-01

Roč. 71, č. 2 (2004), s. 739-746 ISSN 0165-2370 R&D Projects: GA AV ČR IAA4072107; GA MŠk OC 523.60 Institutional research plan: CEZ:AV0Z4072921; CEZ:AV0Z4032918; CEZ:AV0Z4040901 Keywords : dimethyl tellurium * tellurium films * laser Subject RIV: CA - Inorganic Chemistry Impact factor: 1.352, year: 2004

Thermoelectric properties of electrodeposited tellurium films and the sodium lignosulfonate effect

International Nuclear Information System (INIS)

Abad, Begoña; Rull-Bravo, Marta; Hodson, Stephen L.; Xu, Xianfan; Martin-Gonzalez, Marisol

2015-01-01

The effect of the addition of a surfactant, sodium lignosulfonate (SLS), on the thermoelectric properties of tellurium films prepared by electrochemical deposition is studied. The growth mechanism is found to have an important role in the thermoelectric properties since the grain size of the films is sharply reduced when the surfactant is added to the solution. For this reason, the electrical resistivity of the tellurium films when the surfactant is not added is 229 μΩ·m, which is lower than 798 μΩ·m with SLS. The Seebeck coefficient values are not influenced, with values in the vicinity of 285 μV/K for both solutions. The power factor resulted higher values than previous works, reaching values of 280 μW/m·K 2 (without SLS) and 82 μW/m·K 2 (with SLS) at room temperature. Finally, the thermal conductivity was measured by means of the Photoacoustic technique, which showed values of the order of 1 W/m·K for both solutions, which is a factor of 3 less than the bulk value of tellurium. A notable observation is that the power factor and the thermal conductivity of electrodeposited tellurium films have the same order of magnitude of bismuth telluride films grown by electrodeposition. The figure of merit is estimated to be approximately one order of magnitude higher than the bulk value, 0.09 without SLS and 0.03 with SLS, both at room temperature

Influence of ion beam irradiation induced defects on the structural, optical and electrical properties of tellurium nanowires

Energy Technology Data Exchange (ETDEWEB)

Kumar, Narinder [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Department of Physics, Haryana College of Technology & Management, Kaithal, 136027 (India); Kumar, Rajesh [Department of Physics, RN College of Engineering & Technology, Madlauda, 132104 (India); Kumar, Sushil, E-mail: sushil_phys@rediffmail.com [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Chakarvarti, S.K. [Research and Development, Manav Rachana International University, Faridabad, 121001 (India)

2016-11-01

In this study, tellurium nanowires were electrodeposited into the polymer membranes from aqueous acidic bath containing HTeO{sub 2}{sup +} ions. The field emission scanning electron microscopy (FESEM) images confirmed the formation of uniform and straight nanowires. The influence of 110 MeV Ni{sup 8+} ion irradiation induced defects on the structural, optical and electrical properties of as–deposited tellurium nanowires were examined using X-ray diffraction (XRD), UV–visible absorption spectroscopy and current–voltage (I–V) measurements. The XRD data depicted the hexagonal phase of tellurium nanowires and further revealed a variation in the intensity of diffraction peaks of ion irradiated nanowires. Williamson–Hall (WH) analysis is used for convoluting the size and microstrain contributions to the width of diffraction peaks. Tellurium nanowires exhibited a distinct absorbance band in the visible region at 686 nm, while this was absent in bulk tellurium. Electrical properties of nanowires are explored on the basis of I–V curves, which revealed a significant increase in the electrical conductivity of irradiated nanowires. A possible mechanism for the enhanced electrical conductivity is the increase in carrier concentration due to thermally excited defects. The defects produced by ion irradiation play a vital role in modifying the properties of semiconducting nanowires. - Highlights: • 110 MeV Ni{sup 8+} ion beam induced changes in tellurium nanowires have been examined. • Nanowires were prepared using template electrodeposition method. • Irradiation improved the electrical conductivity of tellurium nanowires. • Mechanism for enhanced electrical conductivity of irradiated nanowires was discussed.

Kinetics and mechanism of oxidation of tellurium (IV) by periodate in alkaline medium

International Nuclear Information System (INIS)

Srinivas, K.; Vani, P.; Dikshitulu, L.S.A.

1995-01-01

Detailed kinetic study of the oxidation of tellurium (IV) by periodate in alkaline medium has been carried out to compare the mechanisms of oxidation in the acid and alkaline media. It is interesting to note that the rate step involves a two-electron transfer from tellurium (IV) to periodate in alkaline medium although the kinetic pattern is somewhat different from that in the acid medium. 7 refs., 1 tab

Chemical Process for Treatment of Tellurium and Chromium Liquid Waste from I-131 Radioisotope Production

International Nuclear Information System (INIS)

Zainus-Salimin; Gunandjar; Dedy-Harsono; Hendro; Sugeng-Purnomo; Mohammad-Faruq; Zulfakhri

2000-01-01

The I-131 radioisotope is used in nuclear medicine for diagnosis and therapy. The I-131 radioisotope is produced by wet distillation at Bandung Nuclear Research Center and generated about 4,875 Itr of liquid waste containing 2,532.8 ppm of tellurium and 1,451.8 ppm chromium at pH 1. Considering its negative impact to the environment caused by toxic behaviour of tellurium and chromium, it is necessary to treat chemically that's liquid waste. The research of chemical treatment of tellurium and chromium liquid waste from I-131 radioisotope production has been done. The steps of process are involved of neutralisation with NaOH, coagulation-flocculation process for step I using Ca(OH) 2 coagulant for precipitation of sulphate, sulphite, oxalic, chrome Cr 3+ , and coagulation-flocculation process for step II using BaCI 2 coagulant for precipitation of chrome Cr 6+ and tellurium from the supernatant of coagulation in step I. The best result of experiment was achieved at 0.0161 ppm of chromium concentration on the supernatant from coagulation-flocculation of step I using 3.5 g Ca(OH) 2 for 100 ml of liquid waste, and 0.95 ppm of tellurium concentration on the final supernatant from coagulation-flocculation by of step II using 0.7 g BaCI 2 for supernatant from coagulation of step I. (author)

Enhancement of Au-Ag-Te contents in tellurium-bearing ore minerals via bioleaching

Science.gov (United States)

Choi, Nag-Choul; Cho, Kang Hee; Kim, Bong Ju; Lee, Soonjae; Park, Cheon Young

2018-03-01

The purpose of this study was to enhance the content of valuable metals, such as Au, Ag, and Te, in tellurium-bearing minerals via bioleaching. The ore samples composed of invisible Au and Au paragenesis minerals (such as pyrite, chalcopyrite, sphalerite and galena) in combination with tellurium-bearing minerals (hessite, sylvanite and Tellurobismuthite) were studied. Indigenous microbes from mine drainage were isolated and identified as Acidithiobacillus ferrooxidans, which were used in bioleaching after adaption to copper. The effect of the microbial adaption on the bioleaching performance was then compared with the results produced by the non-adaptive process. The microbial adaption enhanced the Au-Ag-Te contents in biological leaching of tellurium-bearing ore minerals. This suggests that bioleaching with adapted microbes can be used both as a pretreatment and in the main recovery processes of valuable metals.

Peroxide coordination of tellurium in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

2016-02-15

Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Rutherford backscatter measurements on tellurium and cadmium implanted gallium arsenide

International Nuclear Information System (INIS)

Bell, E.C.

1979-10-01

The primary aim of the work described in this thesis was to examine implanted layers of the dopant impurities cadmium and tellurium in gallium arsenide and to experimentally assess their potential for producing electrically active layers. 1.5 MeV Rutherford backscattering measurements of lattice disorder and atom site location have been used to assess post implantation thermal annealing and elevated temperature implantations to site the dopant impurities on either gallium or arsenic lattice positions in an otherwise undisordered lattice. Pyrolitically deposited silicon dioxide was used as an encapsulant to prevent thermal dissociation of the gallium arsenide during annealing. It has been shown that high doses of cadmium and tellurium can be implanted without forming amorphous lattice disorder by heating the gallium arsenide during implantation to relatively low temperatures. Atom site location measurements have shown that a large fraction of a tellurium dose implanted at 180 0 C is located on or near lattice sites. Channeled backscatter measurements have shown that there is residual disorder or lattice strain in gallium arsenide implanted at elevated temperatures. The extent of this disorder has been shown to depend on the implanted dose and implantation temperature. The channeling effect has been used to measure annealing of the disorder. (author)

Phenylethynyl-butyltellurium inhibits the sulfhydryl enzyme Na+, K+ -ATPase: an effect dependent on the tellurium atom.

Science.gov (United States)

Quines, Caroline B; Rosa, Suzan G; Neto, José S S; Zeni, Gilson; Nogueira, Cristina W

2013-11-01

Organotellurium compounds are known for their toxicological effects. These effects may be associated with the chemical structure of these compounds and the oxidation state of the tellurium atom. In this context, 2-phenylethynyl-butyltellurium (PEBT) inhibits the activity of the sulfhydryl enzyme, δ-aminolevulinate dehydratase. The present study investigated on the importance of the tellurium atom in the PEBT ability to oxidize mono- and dithiols of low molecular weight and sulfhydryl enzymes in vitro. PEBT, at high micromolar concentrations, oxidized dithiothreitol (DTT) and inhibited cerebral Na(+), K(+)-ATPase activity, but did not alter the lactate dehydrogenase activity. The inhibition of cerebral Na(+), K(+)-ATPase activity was completely restored by DTT. By contrast, 2-phenylethynyl-butyl, a molecule without the tellurium atom, neither oxidized DTT nor altered the Na(+), K(+)-ATPase activity. In conclusion, the tellurium atom of PEBT is crucial for the catalytic oxidation of sulfhydryl groups from thiols of low molecular weight and from Na(+), K(+)-ATPase.

Study On Analytical Methods Of Tellurium Content In Natriiodide (Na131I) Radiopharmaceutical Solution Produced In The Dalat Nuclear Reactor

International Nuclear Information System (INIS)

Vo Thi Cam Hoa; Duong Van Dong; Nguyen Thi Thu; Chu Van Khoa

2007-01-01

This report describes the practical methods for analyzing of Tellurium content in Na 131 I solution produced at the Dalat Nuclear Research Institute. We studied analytical methods to control Tellurium content in final Na 131 I solution product used in medical purposes by three methods such as: spot test, gamma spectrometric and spectrophotometric methods. These investigation results are shown that the spot test method is suitable for controlling Tellurium trace in the final product. This spot test can be determinate Tellurium trace less than 10 ppm and are used to quality control of Na 131 I solution using in medical application. (author)

Simple and effective method for nuclear tellurium isomers separation from antimony cyclotron targets

International Nuclear Information System (INIS)

Bondarevskij, S.I.; Eremin, V.V.

1999-01-01

Simple and effective method of generation of tellurium nuclear isomers from irradiated on cyclotron metallic antimony is suggested. Basically this method consists in consideration of the big difference in volatilities of metallic forms of antimony, tin and tellurium. Heating of the tin-antimony alloy at 1200 K permits to separate about 90 % of produced quantity of 121m Te and 123m Te (in this case impurity of antimony radionuclides is not more than 1 % on activity) [ru

Simultaneous determination of selenium and tellurium in native sulfur by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Arikawa, Yoshiko; Hirai, Shoji; Ozawa, Takejiro.

1979-01-01

A method for the determination of selenium and tellurium in native sulfur has been investigated by means of atomic absorption spectrophotometry. Native sulfur collected from around fumarole or volcanic crater is ground down into powder, a portion of which weighing 1 g is subjected to analysis. A 2.6% (w/v) sodium hydroxide solution is added by 10 ml to the sample in a teflon beaker, and the mixture is then heated on a hot plate. Sulfur is decomposed and dissolved in the form of disulfide and thiosulfate. A 30% hydrogenperoxide solution is added by 10 ml to oxidize them to sulfate. At the same time selenium and tellurium contained in the sulfur sample are also thought to be oxidized to Se(VI) and Te(VI) states. The solution is neutralized with hydrochloric acid and diluted with distilled water to 100 ml. The sample solution thus prepared is sprayed into the air-acetylene flame of the atomic absorption spectrophotometer. The absorbance is measured at 195.9 nm for selenium and 214.2 nm for tellurium. Calibration curve is prepared by measuring the absorbances of the solutions prepared as follows. One gram portions of pure sulfur (99.9999%) are decomposed as for the samples. After neutralization, standard solutions containing each same amount of selenium and tellurium (0 -- 1000 μg) are added to the sulfur solution and then diluted with water to 100 ml. The standard deviations were estimated to be 50.4 ppm for selenium at 756 ppm and 16.6 ppm for tellurium at 587 ppm. For the check of the reliability of the method, results were compared with those obtained by neutron activation analysis. Results obtained by both methods showed good agreement. (author)

Selenium- or tellurium- containing bile acids and derivatives thereof

International Nuclear Information System (INIS)

Monks, R.; Riley, A.L.M.

1981-01-01

This invention relates to the preparation of selenium and tellurium derivatives, particularly γ-emitting radioactive derivatives of bile acids and bile salts. Such compounds are valuable in the examination of body function, especially small bowel function. (author)

Electrochemical characterization of the underpotential deposition of tellurium on Au electrode

International Nuclear Information System (INIS)

Zhu, W.; Yang, J.Y.; Zhou, D.X.; Bao, S.Q.; Fan, X.A.; Duan, X.K.

2007-01-01

Electrochemical characterization of the underpotential deposition (UPD) of tellurium on Au substrate has been performed in this paper. The mechanism of Te deposition and its voltammetry dependence on the Te ion concentration were studied, and it suggests that variations in the metal ion concentration may affect the UPD process kinetics. The effect of tellurium adsorbates on UPD behavior of Te has also been investigated. The results show that the tellurium adsorbates could be irreversibly adsorbed upon the Au substrate surface under the open-circuit conditions. Subsequent removal of the Te adsorbates was also proved to be very difficult within the Au double-layer region, and a standard electrochemical cleaning procedure is necessary to remove the Te adsorbates completely. When the potential was cycled into the Au oxidation region, a substantial loss of Te adsobates was observed, which occurs simultaneously with the Au oxidation features. Scan rate dependent cyclic voltammetry experiments reveal that the peak current in the Te UPD peak is not a linear function of the scan rate, ν, but of a 2/3 power of the scan rate, ν 2/3 . It is in good consistent with a two-dimension nucleation and growth mechanism

Speciation analysis of tellurium by solid-phase extraction in the presence of ammonium pyrrolidine dithiocarbamate and inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Yu, Chunhai; Cai, Qiantao; Guo, Zhong-Xian; Yang, Zhaoguang [Centre for Advanced Water Technology, Innovation Centre (NTU), Singapore (Singapore); Khoo, Soo Beng [Department of Chemistry, National University of Singapore (Singapore)

2003-05-01

Under acidic conditions tellurium(IV) formed a complex with ammonium pyrrolidine dithiocarbamate (APDC). The tellurium(IV) complex was completely retained on a non-polar Isolute silica-based octadecyl (C{sub 18}) sorbent-containing solid-phase extraction (SPE) cartridge, while the uncomplexed Te(VI) passed through the cartridge and remained as a free species in the solution. Only partial Te(IV) was retained on the SPE cartridge for samples without addition of APDC. On the basis of different retention behaviours of the complexed Te(IV) and uncomplexed Te(VI), a simple and highly sensitive method is proposed for the determination of total tellurium and Te(VI) by SPE separation and inductively coupled plasma mass spectrometry (ICP-MS) detection. The Te(IV) concentration was calculated as the difference between total tellurium and Te(VI) concentrations. The detection limit (3{sigma}) is 3 ng L{sup -1} tellurium. Factors affecting the separation and detection of tellurium species were investigated. Coexisting ions did not show significant interferences with the Te(IV)-APDC complex retention and the subsequent ICP-MS detection of Te. The method has been successfully applied to the tellurium speciation analysis in waters with spiked recoveries for Te(IV) and Te(VI) of 86.0-108% and 87.1-97.4%, respectively. (orig.)

Intergranular tellurium cracking of nickel-based alloys in molten Li, Be, Th, U/F salt mixture

Science.gov (United States)

Ignatiev, Victor; Surenkov, Alexander; Gnidoy, Ivan; Kulakov, Alexander; Uglov, Vadim; Vasiliev, Alexander; Presniakov, Mikhail

2013-09-01

In Russia, R&D on Molten Salt Reactor (MSR) are concentrated now on fast/intermediate spectrum concepts which were recognized as long term alternative to solid fueled fast reactors due to their attractive features: strong negative feedback coefficients, easy in-service inspection, and simplified fuel cycle. For high-temperature MSR corrosion of the metallic container alloy in primary circuit is the primary concern. Key problem receiving current attention include surface fissures in Ni-based alloys probably arising from fission product tellurium attack. This paper summarizes results of corrosion tests conducted recently to study effect of oxidation state in selected fuel salt on tellurium attack and to develop means of controlling tellurium cracking in the special Ni-based alloys recently developed for molten salt actinide recycler and tranforming (MOSART) system. Tellurium corrosion of Ni-based alloys was tested at temperatures up to 750 °C in stressed and unloaded conditions in molten LiF-BeF2 salt mixture fueled by about 20 mol% of ThF4 and 2 mol% of UF4 at different [U(IV)]/[U(III)] ratios: 0.7, 4, 20, 100 and 500. Following Ni-based alloys (in mass%): HN80М-VI (Mo—12, Cr—7.6, Nb—1.5), HN80МТY (Mo—13, Cr—6.8, Al—1.1, Ti—0.9), HN80МТW (Mo—9.4, Cr—7.0, Ti—1.7, W—5.5) and ЕМ-721 (W—25.2, Cr—5.7, Ti—0.17) were used for the study in the corrosion facility. If the redox state the fuel salt is characterized by uranium ratio [U(IV)]/[U(III)] uranium intermetallic compounds and alloys with nickel and molybdenum. This leads to spontaneous behavior of alloy formation processes on the specimens' surface and further diffusion of uranium deep into the metallic phase. As consequence of this films of intermetallic compounds and alloys of nickel, molybdenum, tungsten with uranium are formed on the alloys specimens' surface, and intergranular corrosion does not take place. In the fuel salt with [U(IV)]/[U(III)] = 4-20 the potentials of uranium

Determination of tellurium in coal samples by means of graphite furnace atomic absorption spectrometry after coprecipitation with iron(III) hydroxide

Energy Technology Data Exchange (ETDEWEB)

Oda, S.; Arikawa, Y. [Japan Womens University, Tokyo (Japan)

2005-11-01

A simple and accurate method for the determination of tellurium in coal samples was investigated by the combustion of samples under a high pressure of oxygen and coprecipitation with Fe(OH){sub 3}, followed by a measurement by graphite furnace atomic absorption spectrometry (GF-AAS). About 0.5 g of an accurately weighed ground coal sample and 0.5 g of starch were combusted in an oxygen combustion bomb filled with oxygen to 3 MPa and added with 3 ml of water as an absorbing solution. The formed tellurium trioxide TeOs dissolved in water as TeO{sub 4}{sup 2-}, which was in turn reduced to TeO{sub 3}{sup 2-} by heating. After diluting the above-mentioned solution up to about 50 ml with water, Fe(OH){sub 3} is formed upon adding Fe(NO{sub 3}){sub 3} and sodium hydroxide solutions at pH 8-9 and left standing overnight. After dissolving the precipitate by HCl, the solution was diluted to 10 ml with water and the concentration of tellurium was measured by GF-AAS at a wavelength of 214.3 nm. The standard addition method was employed for the determination of tellurium in real coal samples, because those processes for the formation of tellurium(VI) oxide and coprecipitation with Fe(OH)3 were interfered by matrices. For NIST SRM 1632c, the standard coal sample tellurium content of 0.057 {+-} 0.004 mg kg{sup -1} was in good agreement with the information value of 0.05 mg kg{sup -1} with 7% of RSD in five replicate analyses. The tellurium contents in 20 real coal samples given by Center for Coal Utilization, Japan were also determined. The tellurium contents in these samples were scattered over the narrow range between 0.032 and 0.100 mg kg{sup -1}.

Site-specific nucleation and controlled growth of a vertical tellurium nanowire array for high performance field emitters

International Nuclear Information System (INIS)

Safdar, Muhammad; Zhan Xueying; Mirza, Misbah; Wang Zhenxing; Sun Lianfeng; He Jun; Niu Mutong; Zhang Jinping; Zhao Qing

2013-01-01

We report the controlled growth of highly ordered and well aligned one-dimensional tellurium nanostructure arrays via a one-step catalyst-free physical vapor deposition method. The density, size and fine structures of tellurium nanowires are systematically studied and optimized. Field emission measurement was performed to display notable dependence on nanostructure morphologies. The ordered nanowire array based field emitter has a turn-on field as low as 3.27 V μm −1 and a higher field enhancement factor of 3270. Our finding offers the possibility of controlling the growth of tellurium nanowire arrays and opens up new means for their potential applications in electronic devices and displays. (paper)

Exploring molecular and spin interactions of Tellurium adatom in reduced graphene oxide

Energy Technology Data Exchange (ETDEWEB)

Alegaonkar, Ashwini [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India); Alegaonkar, Prashant [Department of Applied Physics, Defence Institute of Advance Technology, Girinagar, Pune, 411 025, MS (India); Pardeshi, Satish, E-mail: skpar@chem.unipune.ac.in [Department of Chemistry, Savitribai Phule Pune University (Formerly University of Pune), Ganeshkhind, Pune, 411 007, MS (India)

2017-07-01

The transport of spin information fundamentally requires favourable molecular architecture and tunable spin moments to make the medium pertinent for spintronic. We report on achieving coherent molecular-spin parameters for rGO due to Tellurium (Te) adatom. Initially, GO prepared using graphite, was modified into rGO by in situ incorporation of 1 (w/w)% of Te. Both the systems were subjected to ESCA, FTIR, Raman dispersion, ESR spectroscopy, and electron microscopy. Analysis revealed that, Te substantially reacted with epoxides, carbonyl, and carboxylate groups that improved C-to-O ratio by twice. However, the spin splitting character, between Te and C, seems to be quenched. Moreover, Te altered the dynamical force constant between C-C and C=C that generated the mechanical stress within rGO network. The layer conjugation, nature of folding, symmetry, and electronic states of the edges were also affected by precipitation and entrapment of Te. The calculated dynamic molecular Raman and ESR spin parameters indicated that, Te acted as a bridging element for long range spin transport. This is particularly due to, the p-orbital moments of Te contributing, vectorially, to spin relaxation process operative at broken inversion symmetry sites. Our study suggests that, facile addition of Te in rGO is useful to achieve favourable spintronic properties. - Highlights: • Spin interactions and molecular dynamics modification due to Tellurium adatom in rGO. • Molecular level manipulation of Tellurium adatom for favourable spintronic properties. • Bychocov-Rashaba coupling are the operative channels in rGO. • Extrinsic coupling component get added vectorially by Tellurium. • Te-rGO is a viable medium for molecular spintronics.

Dismantling and chemical characterization of spent Peltier thermoelectric devices for antimony, bismuth and tellurium recovery.

Science.gov (United States)

Balva, Maxime; Legeai, Sophie; Garoux, Laetitia; Leclerc, Nathalie; Meux, Eric

2017-04-01

Major uses of thermoelectricity concern refrigeration purposes, using Peltier devices, mainly composed of antimony, bismuth and tellurium. Antimony was identified as a critical raw material by EU and resources of bismuth and tellurium are not inexhaustible, so it is necessary to imagine the recycling of thermoelectric devices. That for, a complete characterization is needed, which is the aim of this work. Peltier devices were manually dismantled in three parts: the thermoelectric legs, the alumina plates on which remain the electrical contacts and the silicone paste used to connect the plates. The characterization was performed using five Peltier devices. It includes mass balances of the components, X-ray diffraction analysis of the thermoelectric legs and elemental analysis of each part of the device. It appears that alumina represents 45% of a Peltier device in weight. The electrical contacts are mainly composed of copper and tin, and the thermoelectric legs of bismuth, tellurium and antimony. Thermoelectric legs appear to be Se-doped Bi 2 Te 3 and (Bi 0,5 Sb 1,5 )Te 3 for n type and p type semiconductors, respectively. This work shows that Peltier devices can be considered as a copper ore and that thermoelectric legs contain high amounts of bismuth, tellurium and antimony compared to their traditional resources.

Comparison of analytical possibilities of inversion voltammetry of tellurium with cathodic and anodic potential scanning taking layer-by-layer analysis of GaAs-Te films as example

International Nuclear Information System (INIS)

Kaplin, A.A.; Portnyagina, Eh.O.; Gridaev, V.F.

1979-01-01

Possibility of application in analytical purposes of the process of tellurium precipitation electrosolution from the surfaces of graphite and mercury-graphite electrodes at the cathode scanning of the potential is shown. As a result of comparison of direct and inversion scanning with cathodic and anodic scanning of the potential, variants of voltammetric method of tellurium determination in artificial solutions and, taking the developed method of layer-by-layer analysis of the GaAsTe films as an example, advantage of mercury-graphite electrode with cathodic scanning as compared to graphite electrode with cathode scanning of the potential is shown. Reproducibility of the GaAs film analysis results according to anodic and cathodic tellurium peaks is satisfactory. Maximum deviation from the results of analysis of oxidation peaks and tellurium peduction does not exceed 15 rel. %. Thus, for tellurium concentrations, exceeding 5x10 -6 g-ion/l, both anodic and cathodic scanning of the potential can be used, though error in tellurium determination according to cathodic peaks is 1.5-2.0 times higher. At tellurium amounts lower 5x10 -6 g-ion/l the determination should be carried out according to the peaks of tellurium anodic oxidation from the surface of graphite electrode or according to the peaks of tellurium cathodic reduction from the surface of mercury-graphite electrode

Modelling the chemical behaviour of tellurium species in the reactor pressure vessel and the reactor cooling system under severe accident conditions

International Nuclear Information System (INIS)

Alonso, A.; Gonzalez, C.

1991-07-01

This state of the art report contains information on the behaviour of tellurium and its compounds in the reactor pressure vessel and the reactor coolant system under light water reactor severe accident conditions. To characterise tellurium behaviour, it is necessary the previous knowledge of the species of tellurium released from the core, and simultaneity of its release with that of other materials which can alter the transport, for instance, control rod and structural materials. Release and transport experiments have been reviewed along with the models implemented in the codes which are used in the international community: TRAPMELT, RAFT, VICTORIA and SOPHIE. From the experiments, it can be concluded that other species different to Te 2 , such as tin telluride and cesium telluride, may be released from the fuel. That is why they must be considered in the transport phenomena. There is also experimental evidence of the strong interaction of Te 2 with Inconel 600 and stainless steel of the pipe walls and structures, however this strong interaction is in competition with the interaction of tellurium with aerosols, which under severe accident conditions may represent an area greater than that of the primary system. It is for the absence of significant tellurium species in the transport models, and also for the interaction of tellurium with aerosols, for which some codes show the greatest deficiencies

The enhancing of Au-Ag-Te content in tellurium-bearing ore mineral by bio-oxidation-leaching

Science.gov (United States)

Kim, PyeongMan; Kim, HyunSoo; Myung, EunJi; Kim, YoonJung; Lee, YongBum; Park*, CheonYoung

2015-04-01

The purpose of this study is to enhance the content of valuable metals such as Au-Ag-Te in tellurium-bearing minerals by bio-oxidation-leaching. It was confirmed that pyrite, chalcopyrite, sphalerite and galena were produced together with tellurium-bearing minerals including hessite, sylvanite and tellurobismuthite from ore minerals and concentrates through microscopic observation and SEM/EDS analysis. In a bio-oxidation-leaching experiment, with regard to Au, Ag, Te, Cu and Fe, the changes in the amount of leaching and the content of leaching residues were compared and analyzed with each other depending on the adaptation of an indigenous microbe identified as Acidithiobacillus ferrooxidans. As a result of the experiment, the Au-Ag-Te content in tellurium-bearing ore mineral was enhanced in the order of physical oxidation leaching, physical/non-adaptive bio-oxidation-leaching and physical/adaptive biological leaching. It suggests that the bio-oxidation-leaching using microbes adapted in tellurium-bearing ore mineral can be used as a pre-treatment and a main process in a recovery process of valuable metals. "This research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education(NRF-2013R1A1A2004898)"

ELECTROCHEMICAL STUDY OF RHENIUM-TELLURIUM-COPPER SYSTEM

OpenAIRE

E.A.Salakhova*1, D.B.Tagiyev2, P.E.Kalantarova3 and A.M.Askerova4

2017-01-01

The formation of the triple alloys Re-Te-Cu on the platinum electrode at volt amperemetric cycling has been studied. The investigation was carried out from chloride acidic solution containing tellurium acid, potassium perrhenate, chloride copper. The kinetics of the processes was controlled using the measurements by the method of cyclic volt-amperometry on the device İVİUMSTAT. For the analysis of composition and structure the methods of XRD (X-ray diffraction analysis) were used, and the inv...

Acousto-optic measurements of ultrasound attenuation in tellurium dioxide crystal

International Nuclear Information System (INIS)

Voloshinov, V. B.; Lemyaskina, E. A.

1996-01-01

The paper is devoted to experimental investigation of ultrasound propagation in tellurium dioxide monocrystal. In particular, attenuation of slow shear acoustic modes in the crystal was measured. The measurements were performed by acousto-optic methods using probing of acoustic column by a laser beam. The paper describes measurements of acoustic attenuation coefficient for slow shear ultrasonic waves propagating at an angle =4.5 O with respect to the (110) direction in the (110) plane. The investigation was made at acoustic frequency f = 100 MHz with pulsed acoustic waves and with an optical beam of a He-Ne laser. It is found that the attenuation coefficient is α = 0.57 cm -1 ± 15 %. The attenuation at acoustic frequencies f ≥ 100 MHz influences performance characteristics of acousto-optical devices based on tellurium dioxide. As proved, spectral resolution of a quasicollinear acoustooptic filter decreases by a factor of 2 compared to a case of the attenuation absence. (authors)

Solvent Extraction of Tellurium from Chloride Solutions Using Tri-n-butyl Phosphate: Conditions and Thermodynamic Data

Directory of Open Access Journals (Sweden)

Dongchan Li

2014-01-01

Full Text Available The extractive separation of tellurium (IV from hydrochloric acid media with tri-n-butyl phosphate (TBP in kerosene was investigated. The dependence on the extraction of tellurium species, concentrations of tellurium and TBP, extraction time and stage, organic/aqueous ratio, and interferences from coexist metallic ions were examined and are discussed. Besides, the stripping agent and stripping time were also studied. It was found that the extraction reaction corresponds to the neutral complex formation mechanism and the extracted species is TeCl4·3TBP and that the extraction process is exothermic. The thermodynamic parameters of enthalpy ΔH, entropy ΔS, and free energy ΔG of the extraction process were evaluated at −26.2 kJ·mol−1, −65.6 J·mol−1·K−1, and −7.0 kJ·mol−1, respectively at 293 K.

Copper Tellurium Oxides - A Playground for Magnetism.

Energy Technology Data Exchange (ETDEWEB)

Norman, M. R.

2018-04-15

A variety of copper tellurium oxide minerals are known, and many of them exhibit either unusual forms of magnetism, or potentially novel spin liquid behavior. Here, I review a number of the more interesting materials with a focus on their crystalline symmetry and, if known, the nature of their magnetism. Many of these exist (so far) in mineral form only, and most have yet to have their magnetic properties studied. This means a largely unexplored space of materials awaits our exploration.

Liquid-liquid extraction of arsenic, antimony, selenium and tellurium by zinc diethyldithiocarbamate

International Nuclear Information System (INIS)

Bajo, S.; Wyttenbach, A.

1978-03-01

The authors report the solvent extraction, oxidation, reduction, extraction in the presence of iron, and reextraction of arsenic, antimony, selenium and tellurium. These processes were studied using radioactive tracers. (G.T.H.)

First example of a high-level correlated calculation of the indirect spin-spin coupling constants involving tellurium

DEFF Research Database (Denmark)

Rusakov, Yury Yu; Krivdin, Leonid B.; Østerstrøm, Freja From

2013-01-01

This paper documents a very first example of a high-level correlated calculation of spin-spin coupling constants involving tellurium taking into account relativistic effects, vibrational corrections and solvent effects for the medium sized organotellurium molecules. The 125Te-1H spin-spin coupling...... constants of tellurophene and divinyl telluride were calculated at the SOPPA and DFT levels in a good agreement with experiment. A new full-electron basis set av3z-J for tellurium derived from the "relativistic" Dyall's basis set, dyall.av3z, and specifically optimized for the correlated calculations...... of spin-spin coupling constants involving tellurium, was developed. The SOPPA methods show much better performance as compared to 15 those of DFT, if relativistic effects calculated within the ZORA scheme are taken into account. Vibrational and solvent corrections are next to negligible, while...

A Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

OpenAIRE

Berman, G. P.; Doolen, G. D.; Tsifrinovich, V. I.

2000-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines the well-developed silicon technology with expected advances in MRFM.

Subnanosecond pulse measurements of 10.6 μm radiation with tellurium

NARCIS (Netherlands)

Haselhoff, E.H.; Bonnie, R.J.M.; Ernst, G.J.; Witteman, W.J.

1988-01-01

Subnanosecond infrared pulses have been measured by noncollinear secondharmonic generation in tellurium. The method is very practical because due to the high refractive index the fine tuning of the phase matching is easily obtained by rotating the crystal around the optic axis.

Flotation concentration for tellurium determination in industrial sewage

International Nuclear Information System (INIS)

Skripchuk, V.G.; Bormotova, L.V.; Lukoyanova, L.P.; Tret'yakova, M.I.

1983-01-01

Combination of the flotation of tellurium (4) precipitate with papaverine toluene and extraction-photometric determination of Te with butylrhodamine C allows one to determine 0.002-0.1 mg Te/l without its preliminary precipitation. Accompanying elements found in non-ferrous metallurgy sewage have no effect upon it. The duration of analysis of 10 samples is 1 to 1.5 h. Relative error is 12%. The method is introduced at the ''Uralelektromed'' plant

Magnetic resonance force microscopy quantum computer with tellurium donors in silicon.

Science.gov (United States)

Berman, G P; Doolen, G D; Hammel, P C; Tsifrinovich, V I

2001-03-26

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations.

Magnetic Resonance Force Microscopy Quantum Computer with Tellurium Donors in Silicon

International Nuclear Information System (INIS)

Berman, G. P.; Doolen, G. D.; Hammel, P. C.; Tsifrinovich, V. I.

2001-01-01

We propose a magnetic resonance force microscopy (MRFM)-based nuclear spin quantum computer using tellurium impurities in silicon. This approach to quantum computing combines well-developed silicon technology and expected advances in MRFM. Our proposal does not use electrostatic gates to realize quantum logic operations

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

International Nuclear Information System (INIS)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F.

2013-01-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

Determination of half life of tellurium isotopes: a proposal for the teaching of nuclear physics

Energy Technology Data Exchange (ETDEWEB)

Ruivo, Julio C.; Zamboni, Cibele B.; Batista, Wagner F., E-mail: julio.ruivo.costa@usp.br, E-mail: czamboni@ipen.br, E-mail: fisicawagner@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

This work aimed at the development of courseware for teaching nuclear physics, using experimental data of half-life measurement (T1/2) of Tellurium isotopes (A=127 and 131). The choice of Tellurium was established for providing nuclear data, which are fundamental in related investigations of nuclear structure and its use in various areas such as geochemistry, chemical and pharmaceutical industries, astrophysics etc. For evaluation of the proposal performance, the material was made available, bringing a lot of information about nuclear safety, production and storage of radioactive material and concepts of radioactive decay, subatomic particles, emission of gamma radiation, half-life, etc.

The dependence of the texture of tellurium thin films on vacuum deposition angle

International Nuclear Information System (INIS)

Cocks, F.H.; Peterson, M.J.; Jones, P.L.

1980-01-01

Vacuum-deposited tellurium thin films can show substantially different surface morphologies depending on the angle with which the vapor stream impinges on the substrate surface. These tellurium thin films have a tendency to grow as acicular crystallites but as the deposition angle is increased so that the vapor stream becomes tangential to the substrate surface the spacing between crystallites increases and approaches, at stream angles of approximately 80 0 from the normal, dimensions roughly once or twice the average wavelength of visible light. Such films may have application in solar energy collector systems because of the high absorptivity of sunlight shown by such films. Mechanisms which describe the tendency for crystallite spacing to increase with increasing angle are discussed. (Auth.)

Large-scale synthesis of Tellurium nanostructures via galvanic displacement of metals

Science.gov (United States)

Kok, Kuan-Ying; Choo, Thye-Foo; Ubaidah Saidin, Nur; Rahman, Che Zuraini Che Ab

2018-01-01

Tellurium (Te) is an attractive semiconductor material for a wide range of applications in various functional devices including, radiation dosimeters, optical storage materials, thermoelectric or piezoelectric generators. In this work, large scale synthesis of tellurium (Te) nanostructures have been successfully carried out in different concentrations of aqueous solutions containing TeO2 and NaOH, by galvanic displacements of Zn and Al which served as the sacrificial materials. Galvanic displacement process is cost-effective and it requires no template or surfactant for the synthesis of nanostructures. By varying the concentrations of TeO2 and NaOH, etching temperatures and etching times, Te nanostructures of various forms of nanostructures were successfully obtained, ranging from one-dimensional needles and rod-like structures to more complex hierarchical structures. Microscopy examinations on the nanostructures obtained have shown that both the diameters and lengths of the Te nanostructures increased with increasing etching temperature and etching time.

Iodine-129 in thyroids and tellurium isotopes in meteorites by neutron activation analysis

International Nuclear Information System (INIS)

Ballad, R.V.

1978-06-01

A combination of neutron activation and mass spectrometry has been used to determine the concentration of fissiogenic 129 I and the value of the 129 I/ 127 I ratio in thyroids of man, cow, and deer from Missouri. Deer thyroids show an average value of 129 I/ 127 I = 1.8 x 10 -8 and an average concentration of 3 x 10 -3 pCi 129 I per gram of thyroid (wet weight). Thyroids of cows and humans show successively lower values for the 129 I/ 127 I ratio and the 129 I content because their diets dilute fission-produced 129 I in the natural iodine cycle with mineral iodine. The results of analyses on a few thyroids from other geographic areas are also reported. The isotopic compositions of tellurium, krypton, and xenon were determined in acid-resistant residues of the Allende meteorite. Neutron activation and γ-counting were used to determine the relative abundances of six tellurium isotopes, and mass spectrometry was used to determine the isotopic compositions of krypton and xenon in aliquots of the same residues. Nucleogenetic anomalies were observed in the isotopic compositions of these three elements. The presence of isotopically distinct components of tellurium, krypton, and xenon in these residues provides strong support for the suggestion that our solar system formed directly from the debris of a supernova

Thermoelectric properties of bismuth antimony tellurium thin films through bilayer annealing prepared by ion beam sputtering deposition

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhuang-hao [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Fan, Ping, E-mail: fanping308@126.com [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Luo, Jing-ting [College of Physics Science and Technology, Shenzhen University, 518060 (China); Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China); Cai, Xing-min; Liang, Guang-xing; Zhang, Dong-ping [College of Physics Science and Technology, Shenzhen University, 518060 (China); Ye, Fan [Shenzhen Key Laboratory of Sensor Technology, Shenzhen 518060 (China)

2014-07-01

Bismuth antimony tellurium is one of the most important tellurium-based materials for high-efficient thermoelectric application. In this paper, ion beam sputtering was used to deposit Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films on borosilicate substrates at room-temperature. Then the bismuth antimony tellurium thin films were synthesized via post thermal treatment of the Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} bilayer thin films. The effect of annealing temperature and compositions on the thermoelectric properties of the thin films was investigated. After the thin films were annealed from 150 °C to 350 °C for 1 h in the high vacuum condition, the Seebeck coefficient changed from a negative sign to a positive sign. The X-ray diffraction results showed that the synthesized tellurium-based thermoelectric thin film exhibited various alloys phases, which contributed different thermoelectricity conductivity to the synthesized thin film. The overall Seebeck coefficient of the synthesized thin film changed from negative sign to positive sign, which was due to the change of the primary phase of the tellurium-based materials at different annealing conditions. Similarly, the thermoelectric properties of the films were also associated with the grown phase. High-quality thin film with the Seebeck coefficient of 240 μV K{sup −1} and the power factor of 2.67 × 10{sup −3} Wm{sup −1} K{sup −2} showed a single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase when the Sb/Te thin film sputtering time was 40 min. - Highlights: • Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} thermoelectric thin films synthesized via bilayer annealing • The film has single Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} phase with best thermoelectric performance. • The film has high thermoelectric properties comparable with other best results.

Equilibrium state of delta-phase with tellurium in the Sb-Bi-Te system

International Nuclear Information System (INIS)

Gajgukova, V.S.; Dudkin, L.D.; Erofeev, R.S.; Musaelyan, V.V.; Nadzhip, A.Eh.; Sokolov, O.B.

1978-01-01

A research has been carried out with a view to establish the equilibrium state of delta-phase of the composition (Sbsub(1-x)Bisub(x)) 2 Te 3 with tellurium, depending on x and temperature. The Hall effect, the thermoelectromotive force, and the electric conductivity of the samples of Sb-Bi-Te alloys have been measured, the samples being annealed at various temperatures (550 to 250 deg C). The measurement results have shown that as the Bi 2 Te 3 content in the solid solutions increases and temperature decreases, the delta-phase-Te boundary monotonously approaches the stoichiometric composition. Using the research carrid out as the basis, the general character of the equilibrium delta-phase with tellurium boundary has been rendered more precise in Sb-Bi-Te system, depending on the temperature and Bi content (up to 25 at.%)

GALVANIC MAGNETIC PROPERTIES OF BISMUTH THIN FILMS DOPED WITH TELLURIUM MADE BY THERMAL VACUUM EVAPORATION

Directory of Open Access Journals (Sweden)

V. A. Komarov

2013-01-01

Full Text Available The influence of n-type impurity of tellurium (concentration range from 0.005 atomic % Te to 0.15 atomic % Te on galvanic magnetic properties (resistivity, magnetic resistance and Hall constant of Bi thin films with various thicknesses was studied. The properties were measured in temperature range from 77 to 300 K. It was established that the classical size effect in the films is significant and decreases with higher concentration of Te impurity. The analysis of experimental results was carried out in approximation of the law of Jones-Schoenberg dispersion for Bi films doped with tellurium. Calculation of concentration and mobility of charge carriers in the studied films was made.

Hydrogen-assisted post-growth substitution of tellurium into molybdenum disulfide monolayers with tunable compositions

Science.gov (United States)

Yin, Guoli; Zhu, Dancheng; Lv, Danhui; Hashemi, Arsalan; Fei, Zhen; Lin, Fang; Krasheninnikov, Arkady V.; Zhang, Ze; Komsa, Hannu-Pekka; Jin, Chuanhong

2018-04-01

Herein we report the successful doping of tellurium (Te) into molybdenum disulfide (MoS2) monolayers to form MoS2x Te2(1-x) alloy with variable compositions via a hydrogen-assisted post-growth chemical vapor deposition process. It is confirmed that H2 plays an indispensable role in the Te substitution into as-grown MoS2 monolayers. Atomic-resolution transmission electron microscopy allows us to determine the lattice sites and the concentration of introduced Te atoms. At a relatively low concentration, tellurium is only substituted in the sulfur sublattice to form monolayer MoS2(1-x)Te2x alloy, while with increasing Te concentration (up to ˜27.6% achieved in this study), local regions with enriched tellurium, large structural distortions, and obvious sulfur deficiency are observed. Statistical analysis of the Te distribution indicates the random substitution. Density functional theory calculations are used to investigate the stability of the alloy structures and their electronic properties. Comparison with experimental results indicate that the samples are unstrained and the Te atoms are predominantly substituted in the top S sublattice. Importantly, such ultimately thin Janus structure of MoS2(1-x)Te2x exhibits properties that are distinct from their constituents. We believe our results will inspire further exploration of the versatile properties of asymmetric 2D TMD alloys.

7 CFR 1150.118 - Marketing.

Science.gov (United States)

2010-01-01

... 7 Agriculture 9 2010-01-01 2009-01-01 true Marketing. 1150.118 Section 1150.118 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Definitions § 1150.118 Marketing. Marketing means the sale or other disposition in commerce of...

7 CFR 1260.118 - Cattle.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Cattle. 1260.118 Section 1260.118 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Promotion and Research Order Definitions § 1260.118 Cattle. Cattle means live domesticated bovine animals...

Electric field fluctuations in liquid tellurium alloys a hint to bond character

NARCIS (Netherlands)

Paulick, C.A.; Brinkmann, R.; Elwenspoek, Michael Curt; von Hartrott, M.; Kiehl, M.; Maxim, P.; Quitmann, D.

1985-01-01

Atomic scale electric field fluctuations in liquid tellurium alloys are detected as they induce nuclear spin relaxation rate RQ in noble gas impurity atoms, via quadrupolar interaction. Results for Xe in liquid Ag, Ga, In, Tl, Ge, Sn---Te alloys are discussed, assuming that bonding in these alloys

7 CFR 900.118 - Costs.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Costs. 900.118 Section 900.118 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... Meetings To Arbitrate and Mediate Disputes Relating to Sales of Milk or Its Products § 900.118 Costs. The...

Vaporization studies on elemental tellurium and selenium by Knudsen effusion mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, R., E-mail: rvis1953@gmail.com; Balasubramanian, R., E-mail: rbs@igcar.gov.in; Darwin Albert Raj, D., E-mail: darwinalbertraj1953@gmail.com; Sai Baba, M., E-mail: msb@igcar.gov.in; Lakshmi Narasimhan, T.S., E-mail: tslak@igcar.gov.in

2014-08-01

Highlights: • A detailed KEMS study of vaporization of elemental tellurium and selenium systems. • Clusters Te{sub i}(g) (i = 2 to 7) and Se{sub i}(g) (i = 2 to 9) identified over Te(s) and Se(s). • p–T relations for Te{sub i}(g) (590 to 690 K) and Se{sub i}(g) (380 to 480 K). • Vapor phase of Te dominated by Te{sub 2}(g) (∼95%) while that of Se by Se{sub 6}(g) (∼50%) and Se{sub 5}(g) (∼25%). • Sublimation and atomization enthalpies deduced for Te{sub i}(g) and Se{sub i}(g). - Abstract: Vaporization studies on elemental tellurium and selenium were conducted by Knudsen effusion mass spectrometry in the temperature range of 590–690 K and 380–480 K, respectively. The ionic species Te{sub i}{sup +} (i = 1–7) and Se{sub i}{sup +}(g) (i = 1–9) were detected in the mass spectra over these two condensed phases. Measurement of ion intensities were performed as a function of electron impact energy and as a function of temperature (at different electron impact energies) for identifying the gaseous precursor species as well as for determining the partial pressure–temperature relations and sublimation enthalpies for these species. While the major species over elemental tellurium was confirmed to be Te{sub 2}(g) (with all other gaseous species Te{sub 3}–Te{sub 7} put together constituting less than 5%), the major species over elemental selenium was found to be Se{sub 6}(g), closely followed by Se{sub 5}(g) (with other gaseous species Se{sub 2}–Se{sub 4} and Se{sub 7}–Se{sub 9} put together also moderately constituting ∼25%). From the partial pressures, the thermodynamic data for the sublimation reactions i Te(s) = Te{sub i}(g) and i Se(s) = Se{sub i}(g) were deduced by second- and third-law methods. The atomization enthalpies of tellurium and selenium clusters were also deduced by using the recommended enthalpies of formation of monomeric species. Comparison of the findings obtained in the present study with those in previous studies revealed

Starting material radiation source for Moessbauer investigations of tellurium compounds

International Nuclear Information System (INIS)

Alexandrov, A.J.; Grushko, J.S.; Makarov, E.F.; Mishin, K.Y.; Baltrunas, D.A.J.

1977-01-01

A method is described of preparing a radiation source for Mossbauer investigations of tellurium compounds manufactured on the basis of 5 MgO . Te 124 O 3 . 5 MgO . Te 124 O 3 is irradiated in a reactor by means of thermal neutrons, followed by annealing at a temperature ranging from 600 0 to 1,100 0 C for a period of from 5 to 10 hours

Synthesis of ultra-thin tellurium nanoflakes on textiles for high-performance flexible and wearable nanogenerators

Energy Technology Data Exchange (ETDEWEB)

He, Wen; Van Ngoc, Huynh; Qian, Yong Teng; Hwang, Jae Seok; Yan, Ya Ping [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of); Choi, Hongsoo [Department of Robotics Engineering, Daegu Gyeongbuk Institute of Science and Technology (DGIST), 711-873, Daegu (Korea, Republic of); Kang, Dae Joon, E-mail: djkang@skku.edu [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of)

2017-01-15

Highlights: • Ultra-thin tellurium (Te) nanoflakes were successfully grown on textile and used as an active piezoelectric material. • Te nanoflake nanogenerator device was systematically studied by bending and compressing test. • The ultra-high output power during compressing test can light up 10 LEDs without any external power source. • The device can offer a breakthrough in applying tellurium nanoflakes into high-performance flexible and wearable piezoelectric nanogenerator. - Abstract: We report that ultra-thin tellurium (Te) nanoflakes were successfully grown on a sample of a gold-coated textile, which then was used as an active piezoelectric material. An output voltage of 4 V and a current of 300 nA were obtained from the bending test under a driving frequency of 10 Hz. To test the practical applications, Te nanoflake nanogenerator (TFNG) device was attached to the subject’s arm, and mechanical energy was converted to electrical energy by means of periodic arm-bending motions. The optimized open-circuit voltage and short-circuit current density of approximately 125 V and 17 μA/cm{sup 2}, respectively, were observed when a TFNG device underwent a compression test with a compressive force of 8 N and driving frequency of 10 Hz. This high-power generation enabled the instantaneous powering of 10 green light-emitting diodes that shone without any assistance from an external power source.

Catalytic activity of oxide cerium-molybdenum-tellurium catalysts in oxidation ammonolysis

International Nuclear Information System (INIS)

Dzhordano, N.; Bart, D.; Madzhori, R.

1984-01-01

A commercial catalyst containing a mixture of Ce-, Mo-, Te oxides deposited on SiO 2 is shown to manifest a high efficiency in oxidative ammonolysis of propylene (C 3 - ) to acrylonitrile (AN). The dependence of the catalytic properties on the catalyst composition and reaction conditions is studied. It is established that three-component mixtures are more active and selective than the systems with a lesser number of components. Using the catalyst with the optimum ratio of constituent oxides in a microreactor at 440 deg enabled one to achieve initial selectivity in terms of AN equal to 82.5% at 97% conversion of C 3 - . Acrolein, acetonitrile, HCN and nitrogen oxides are the reaction by-products. A supposition is made that the reaction proceeds via the formation of π-compleXes on the centres of Te(4). Setective oxidation occurs on oxygen atoms bonded with the Mo(6) ions. Tellurium enhances the molybdenum reducibleness due to delocalization of electrons, whereas the cerium addition to the mixture of tellurium- and molybdenum oxides increases the rate of molybdenum reoxidation and thus enhances the catalytic system stability

Determination of spins and radioactive widths of tellurium nuclear levels with capturre gamma rays

International Nuclear Information System (INIS)

Bianchini, F.G.

1973-01-01

Spins and levels widths of the tellurium, mainly 128 Te and 130 Te, were determinated by gamma spectroscopy. Measurements of inelastic and elastic scattering, angular distribution and scattering temperature dependence, were still made. Energy levels of this isotopes, were also determinated [pt

48 CFR 18.118 - Trade agreements.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Trade agreements. 18.118 Section 18.118 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACTING METHODS AND CONTRACT TYPES EMERGENCY ACQUISITIONS Available Acquisition Flexibilities 18.118 Trade agreements...

Selenium and tellurium nanomaterials

Science.gov (United States)

Piacenza, Elena; Presentato, Alessandro; Zonaro, Emanuele; Lampis, Silvia; Vallini, Giovanni; Turner, Raymond J.

2018-04-01

Over the last 40 years, the rapid and exponential growth of nanotechnology led to the development of various synthesis methodologies to generate nanomaterials different in size, shape and composition to be applied in various fields. In particular, nanostructures composed of Selenium (Se) or Tellurium (Te) have attracted increasing interest, due to their intermediate nature between metallic and non-metallic elements, being defined as metalloids. Indeed, this key shared feature of Se and Te allows us the use of their compounds in a variety of applications fields, such as for manufacturing photocells, photographic exposure meters, piezoelectric devices, and thermoelectric materials, to name a few. Considering also that the chemical-physical properties of elements result to be much more emphasized when they are assembled at the nanoscale range, huge efforts have been made to develop highly effective synthesis methods to generate Se- or Te-nanomaterials. In this context, the present book chapter will explore the most used chemical and/or physical methods exploited to generate different morphologies of metalloid-nanostructures, focusing also the attention on the major advantages, drawbacks as well as the safety related to these synthetic procedures.

Deposition of tellurium films by decomposition of electrochemically-generated H{sub 2}Te: application to radiative cooling devices

Energy Technology Data Exchange (ETDEWEB)

Engelhard, T.; Jones, E.D.; Viney, I. [Coventry Univ. (United Kingdom). Centre for Data Storage Mater.; Mastai, Y.; Hodes, G. [Department of Materials and Interfaces, Weizmann Institute of Science, 76100, Rehovot (Israel)

2000-07-17

The preparation of homogenous, large area thin layers of tellurium on thin polyethylene foils is described. The tellurium was formed by room temperature decomposition of electrochemically generated H{sub 2}Te. Pre-treatment of the polyethylene substrates with KMnO{sub 4} to give a Mn-oxide layer was found to improve the Te adhesion and homogeneity. Optical characterization of the layers was performed using UV/VIS/NIR spectroscopy. Such coatings have favorable characteristics for use as solar radiation shields in radiative cooling devices. The simplicity of generation of the very unstable H{sub 2}Te was also exploited to demonstrate formation of size-quantized CdTe nanocrystals. (orig.)

33 CFR 118.130 - Fog signals.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Fog signals. 118.130 Section 118... LIGHTING AND OTHER SIGNALS § 118.130 Fog signals. On waterways where visibility is frequently reduced due to fog or other causes, the District Commander may require or authorize the installation of one or...

NMR spectroscopy of organic compounds of selenium and tellurium. Communication 8. Constants of spin-spin interaction of /sup 125/Te-/sup 1/o/sup 3/C in nmr spectra of unsaturated organtellurides

Energy Technology Data Exchange (ETDEWEB)

Kalabin, G.A.; Kushnarev, D.F.; Valeev, R.B. (Irkutskij Gosudarstvennyj Univ. (USSR))

1981-06-01

On the basis of /sup 13/C NMR spectra of a series of unsaturated and aromatic tellurium compounds the constants of spin-spin interaction (SSIC) (sup(1.2)J(Te, C)) are measured. A reliable linear relation between /sup 1/J(Te, C) and s-character of a carbon orbitale forming bond with tellurium is found. Correlation of straight SSIC of carbon with selenium and tellurium in isological compounds is established.

45 CFR 400.118 - Case planning.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Case planning. 400.118 Section 400.118 Public... Services § 400.118 Case planning. (a) A State, or its designee under § 400.117, must develop and implement... services. (b) Case planning for unaccompanied minors must, at a minimum, address the following elements: (1...

A new tellurium-containing amphiphilic molecule induces apoptosis in HCT116 colon cancer cells.

Science.gov (United States)

Du, Peng; Saidu, Nathaniel Edward Bennett; Intemann, Johanna; Jacob, Claus; Montenarh, Mathias

2014-06-01

Chalcogen-based redox modulators over the years have attracted considerable attention as anti-cancer agents. New selenium- and tellurium-containing compounds with a polar head group and aryl-groups of various lengths have recently been reported as biologically active in several organisms. In the present study, we used the most active of the tellurium compound DP41, and its selenium counterpart DP31 to investigate their effects on the human cancer cell line HCT116. Cells were treated with DP41 or DP31 and the formation of superoxide radicals was determined using dihydroethidium. Cell cycle analysis and apoptosis was determined by cytofluorimetry. Proteins involved in ER signaling and apoptosis were determined by Western blot analysis and fluorescence microscopy. With 50μM of DP41, we observed an increase in O2(-) formation. There was, however, no such increase in O2(-) after treatment with the corresponding selenium compound under the same conditions. In the case of DP41, the production of O2(-) radicals was followed by an up-regulation of Nrf2, HO-1, phospho-eIF2α and ATF4. CHOP was also induced and cells entered apoptosis. Unlike the cancer cells, normal retinal epithelial ARPE-19 cells did not produce elevated levels of O2(-) radicals nor did they induce the ER signaling pathway or apoptosis. The tellurium-containing compound DP41, in contrast to the corresponding selenium compound, induces O2(-) radical formation and oxidative and ER stress responses, including CHOP activation and finally apoptosis. These results indicate that DP41 is a redox modulating agent with promising anti-cancer potentials. Copyright © 2014 Elsevier B.V. All rights reserved.

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

International Nuclear Information System (INIS)

Mal, Joyabrata; Nancharaiah, Yarlagadda V.; Maheshwari, Neeraj; Hullebusch, Eric D. van; Lens, Piet N.L.

2017-01-01

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO 3 2− ) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L −1 d −1 . After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO 3 2− L −1 for 42 d before increasing the influent concentration to 20 mg TeO 3 2− L −1 . Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L −1 ) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

46 CFR 118.600 - Fire axe.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Fire axe. 118.600 Section 118.600 Shipping COAST GUARD... OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS FIRE PROTECTION EQUIPMENT Additional Equipment § 118.600 Fire axe. A vessel of more than 19.8 meters (65 feet) in length must have at least one fire axe...

46 CFR 118.400 - Where required.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Where required. 118.400 Section 118.400 Shipping COAST... Extinguishing and Detecting Systems § 118.400 Where required. (a) The following spaces must be equipped with a... unoccupied space with a gross volume of not more than 170 cubic meters (6,000 cubic feet); (2) A pre...

Synthesis and structure of aromatic and heterocyclic compounds of tellurium

International Nuclear Information System (INIS)

Sadekov, I.D.; Maksimenko, A.A.; Rivkin, B.B.

1983-01-01

A new universal method of preparing assymmetric and symmetric diaryl-tellurium chlorides and-dibromides, based on the interaction of diarylditellurides with cations of aryl-diazonium in the presence of copper (2) halogenides is developed. High yields of diaryltellium dihalogenices (60-90 de %), the possibility of the a wide variation of the nature of substituents in both components make this reaction one of the most general methods of preparing assymmetric diaryltellurium dihalogenides. It is advisable to use aryldiazonium boron fluorides instead of halogenides in this reaction

Characterization of tellurium-based films for NO2 detection

International Nuclear Information System (INIS)

Tsiulyanu, D.; Tsiulyanu, A.; Liess, H.-D.; Eisele, I.

2005-01-01

Sensing characteristics of tellurium-based thin films for NO 2 monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO 2 with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO 2 sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms

Tellurium adsorption on tungsten and molybdenum field emitters

International Nuclear Information System (INIS)

Collins, R.A.; Kiwanga, C.A.

1977-01-01

Studies of the adsorption of tellurium onto tungsten and molybdenum field emitters are described and the results obtained are compared with those obtained in previous work on the adsorption of silicon and selenium. The adsorption of Te onto W was found to be much more uniform than in the case of Se. Although Te is metallic in many of its properties its adsorptive behavior on field emitters is found to be similar to that of selenium and these adsorptive properties are basically common to all semiconductors. The most evident property of these adsorbates is that the work function and emission current decrease simultaneously at coverages of less than half a monolayer and the work function subsequently increases. (B.D.)

9 CFR 3.118 - Handling.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

Energy Technology Data Exchange (ETDEWEB)

Forootanfar, Hamid [Herbal and Traditional Medicines Research Center, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Amirpour-Rostami, Sahar; Jafari, Mandana [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Forootanfar, Amir [Department of Pharmacology and Toxicology, Faculty of Pharmacy, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of); Yousefizadeh, Zahra [The Student Research Committee, Faculty of Pharmacy, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of); Shakibaie, Mojtaba, E-mail: shakiba@kmu.ac.ir [Pharmaceutics Research Center, Institute of Neuropharmacology, Kerman University of Medical Sciences, Kerman (Iran, Islamic Republic of)

2015-04-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K{sub 2}TeO{sub 3}. - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K{sub 2}TeO{sub 3}.

Microbial-assisted synthesis and evaluation the cytotoxic effect of tellurium nanorods

International Nuclear Information System (INIS)

Forootanfar, Hamid; Amirpour-Rostami, Sahar; Jafari, Mandana; Forootanfar, Amir; Yousefizadeh, Zahra; Shakibaie, Mojtaba

2015-01-01

The present study was designed to isolate bacterial strain capable of tellurium nanorods' (Te NRs) production followed by purification and evaluation of the cytotoxic effect of Te NRs. Among 25 environmental samples collected for screening of Te NR-producer bacterial strains one bacterial colony (isolated from hot spring and identified as Pseudomonas pseudoalcaligenes strain Te) was selected and applied for biosynthesis of Te NRs. Thereafter, an organic–aqueous partitioning system was applied for the purification of the biogenic Te NRs and the purified Te NRs were characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction spectroscopy (XRD), UV–visible spectroscopy, and Fourier transform infrared spectroscopy (FTIR) techniques. The cytotoxic effect of biologically synthesized Te NRs and potassium tellurite on four cell lines of MCF-7, HT1080, HepG2 and A549 was then determined using the MTT assay method. The obtained results revealed lower toxicity for the rod-shaped biogenic tellurium nanostructures (~ 22 nm diameter by 185 nm length) compared to K 2 TeO 3 . - Highlights: • Te NR producing bacterial strain were isolated from hot springs. • Organic–aqueous partitioning system was applied for purification of Te nanorods. • The rod-shaped biogenic Te NPs showed lower cytotoxicity compared to K 2 TeO 3

Continuous removal and recovery of tellurium in an upflow anaerobic granular sludge bed reactor

Energy Technology Data Exchange (ETDEWEB)

Mal, Joyabrata, E-mail: joyabrata2006@gmail.com [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Nancharaiah, Yarlagadda V. [Biofouling and Biofilm Processes Section, Water and Steam Chemistry Division, Bhabha Atomic Research Centre, Kalpakkam, 603102, Tamil Nadu (India); Homi Bhabha National Institute, Anushakti Nagar Complex, Mumbai 400094 (India); Maheshwari, Neeraj [CNRS UMR 7338, BMBI University de Technologie Compiegne, 60200 Compiegne (France); Hullebusch, Eric D. van [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Université Paris-Est, Laboratoire Géomatériaux et Environnement (LGE), EA 4508, UPEM, 77454, Marne-la-Vallée (France); Lens, Piet N.L. [UNESCO-IHE, Westvest 7, 2611 AX Delft (Netherlands); Department of Chemistry and Bioengineering, Tampere University of Technology, P.O-Box 541, Tampere (Finland)

2017-04-05

Highlights: • Tellurite bioreduction coupled to recovery of biogenic Te(0) nanocrystals. • First report on continuous tellurite removal in a UASB reactor. • Biogenic Te(0) was mainly associated with loosely-bound EPS of granular sludge. • Repeated exposure to tellurite caused compositional changes in the EPS matrix. - Abstract: Continuous removal of tellurite (TeO{sub 3}{sup 2−}) from synthetic wastewater and subsequent recovery in the form of elemental tellurium was studied in an upflow anaerobic granular sludge bed (UASB) reactor operated at 30 °C. The UASB reactor was inoculated with anaerobic granular sludge and fed with lactate as carbon source and electron donor at an organic loading rate of 0.6 g COD L{sup −1} d{sup −1}. After establishing efficient and stable COD removal, the reactor was fed with 10 mg TeO{sub 3}{sup 2−} L{sup −1} for 42 d before increasing the influent concentration to 20 mg TeO{sub 3}{sup 2−} L{sup −1}. Tellurite removal (98 and 92%, respectively, from 10 and 20 mg Te L{sup −1}) was primarily mediated through bioreduction and most of the removed Te was retained in the bioreactor. Characterization using XRD, Raman spectroscopy, SEM-EDX and TEM confirmed association of tellurium with the granular sludge, typically in the form of elemental Te(0) deposits. Furthermore, application of an extracellular polymeric substances (EPS) extraction method to the tellurite reducing sludge recovered up to 78% of the tellurium retained in the granular sludge. This study demonstrates for the first time the application of a UASB reactor for continuous tellurite removal from tellurite-containing wastewater coupled to elemental Te(0) recovery.

Surface studies on graphite furnace platforms covered with Pd, Rh and Ir as modifiers in graphite furnace atomic absorption spectrometry of tellurium

Energy Technology Data Exchange (ETDEWEB)

Pedro, Juana [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Stripekis, Jorge [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina); Departamento de Ingeniería Química, Instituto Tecnológico de Buenos Aires, Av. Eduardo Madero 399 (1106), Buenos Aires (Argentina); Bonivardi, Adrian [Area de Química Analítica, Departamento de Química, Facultad de Ingeniería Química, Universidad Nacional del Litoral, Santiago del Estero 2829 (S3000GL.N), Santa Fe (Argentina); Tudino, Mabel, E-mail: tudino@qi.fcen.uba.ar [Laboratorio de Análisis de Trazas, Departamento de Química Inorgánica, Analítica y Química Física, INQUIMAE, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria (1428), Buenos Aires (Argentina)

2015-05-01

The main objective of this work is the study of correlations between the efficiency of the distribution of the permanent platinum group modifiers Pd, Rh and Ir over the graphite surface with the aim of improving analytical signal of tellurium. Modifier solution was deposited onto the platform and pyrolysed after drying. In the case of Pd, the physical vaporization/deposition technique was also tested. In order to analyze the differences amongst coverings (morphology, topology and distribution), the graphite surfaces were studied with scanning electron microscopy and energy dispersive X-ray microscopy. Micrographs for physical vaporization and pyrolytic deposition of Pd were also analyzed in order to explain the lack of signal obtained for tellurium with the first alternative. Similar micrographs were obtained for pyrolytic deposition of Ir and Rh and then, compared to those of Pd. Ir showed the most homogeneous distribution on the graphite surface and the tallest and sharpest transient. With the aim of improving the analytical signal of tellurium, the correlation between the surface studies and the tellurium transient signal (height, area and shape) is discussed. - Highlights: • Distribution of Rh, Pd and Ir onto graphite furnaces is evaluated by SEM and EDX • Micrographs and spectra showed that surface distribution could influence Te signal. • Ir showed the best signal together with the most homogeneous surface distribution. • Pd-PVD micrographs revealed the absence of graphite and no signal for Te.

Tellurium labeled analogues of the fatty acid hexadecenoic acid for imaging of myocardial tissue

International Nuclear Information System (INIS)

Mills, S.L.

1980-01-01

Non-invasive nuclear diagnostic procedures for the evaluation of acute myocardial infarction and ischemia are currently limited by problems associated with the availablity of radiopharmaceuticals, development of imaging equipment, and inherent characteristics of radionuclides. Myocardial tissue requires high levels of substrates which provide energy for the continuous functioning of this vital organ. Of the major sources of energy, the most utilized source is fatty acids. Tellurium-123m, with excellent gamma imaging characteristics was chosen as the radionuclide. A 16 carbon fatty acid, hexadecenoic acid, was chosen as the carrier molecule. The tellurium-123m fatty acid radiopharmaceuticals were formulated either in a solution of 20 percent ethanol, two percent polysorbate 80, and brought to volume with normal saline or in 12.5 percent human serum ablumin and brought to volume with normal saline. Biodistribution was performed in three animal species: Sprague-Dawley rats (three rats per time frame), Australian white rabbits (three rabbits per time frame), and mongrel dogs (one dog per time frame). Dosimetry calculations were performed to assess the radiation dose

Tellurium quantum dots: Preparation and optical properties

Science.gov (United States)

Lu, Chaoyu; Li, Xueming; Tang, Libin; Lai, Sin Ki; Rogée, Lukas; Teng, Kar Seng; Qian, Fuli; Zhou, Liangliang; Lau, Shu Ping

2017-08-01

Herein, we report an effective and simple method for producing Tellurium Quantum dots (TeQDs), zero-dimensional nanomaterials with great prospects for biomedical applications. Their preparation is based on the ultrasonic exfoliation of Te powder dispersed in 1-methyl-2-pyrrolidone. Sonication causes the van der Waals forces between the structural hexagons of Te to break so that the relatively coarse powder breaks down into nanoscale particles. The TeQDs have an average size of about 4 nm. UV-Vis absorption spectra of the TeQDs showed an absorption peak at 288 nm. Photoluminescence excitation (PLE) and photoluminescence (PL) are used to study the optical properties of TeQDs. Both the PLE and PL peaks revealed a linear relationship against the emission and excitation energies, respectively. TeQDs have important potential applications in biological imaging and catalysis as well as optoelectronics.

48 CFR 1371.118 - Changes-ship repair.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Changes-ship repair. 1371.118 Section 1371.118 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE DEPARTMENT SUPPLEMENTAL REGULATIONS ACQUISITIONS INVOLVING SHIP CONSTRUCTION AND SHIP REPAIR Provisions and Clauses 1371.118 Changes—ship repair. Insert clause...

33 CFR 118.140 - Painting bridge piers.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Painting bridge piers. 118.140 Section 118.140 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.140 Painting bridge piers. The District Commander may require...

Continuous reduction of tellurite to recoverable tellurium nanoparticles using an upflow anaerobic sludge bed (UASB) reactor.

Science.gov (United States)

Ramos-Ruiz, Adriana; Sesma-Martin, Juan; Sierra-Alvarez, Reyes; Field, Jim A

2017-01-01

According to the U.S. Department of Energy and the European Union, tellurium is a critical element needed for energy and defense technology. Thus methods are needed to recover tellurium from waste streams. The objectives of this study was to determine the feasibility of utilizing upflow anaerobic sludge bed (UASB) reactors to convert toxic tellurite (Te IV ) oxyanions to non-toxic insoluble elemental tellurium (Te 0 ) nanoparticles (NP) that are amendable to separation from aqueous effluents. The reactors were supplied with ethanol as the electron donating substrate to promote the biological reduction of Te IV . One reactor was additionally amended with the redox mediating flavonoid compound, riboflavin (RF), with the goal of enhancing the bioreduction of Te IV . Its performance was compared to a control reactor lacking RF. The continuous formation of Te 0 NPs using the UASB reactors was found to be feasible and remarkably improved by the addition of RF. The presence of this flavonoid was previously shown to enhance the conversion rate of Te IV by approximately 11-fold. In this study, we demonstrated that this was associated with the added benefit of reducing the toxic impact of Te IV towards the methanogenic consortium in the UASB and thus enabled a 4.7-fold higher conversion rate of the chemical oxygen demand. Taken as a whole, this work demonstrates the potential of a methanogenic granular sludge to be applied as a bioreactor technology producing recoverable Te 0 NPs in a continuous fashion. Copyright © 2016 Elsevier Ltd. All rights reserved.

33 CFR 118.60 - Characteristics of lights.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Characteristics of lights. 118.60 Section 118.60 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.60 Characteristics of lights. All lights required or authorized under this...

Characterization of tellurium-based films for NO{sub 2} detection

Energy Technology Data Exchange (ETDEWEB)

Tsiulyanu, D. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of)]. E-mail: tsiu@cni.md; Tsiulyanu, A. [Technical University, Department of Physics, bul. Dacia 41, MD-2060 Kishinau (Moldova, Republic of); Liess, H.-D. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany); Eisele, I. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany)

2005-08-01

Sensing characteristics of tellurium-based thin films for NO{sub 2} monitoring was studied systematically. The influence of contact materials, thermal treatment, temperature and thickness of the samples on the electrical conductivity and sensitivity to NO{sub 2} with respect to scanning electron microscopy analyses is given. The possibility is shown to optimize the properties of the films for the development of a simple and stable NO{sub 2} sensor device with rapid response/recovery time and low operating temperature. The sensing mechanism is discussed for the direct interaction of gaseous species with lone-pair electrons of chalcogen atoms.

Strong nonlinear photonic responses from microbiologically synthesized tellurium nanocomposites

Science.gov (United States)

Liao, K.-S.; Wang, Jingyuan; Dias, S.; Dewald, J.; Alley, N.J.; Baesman, S.M.; Oremland, R.S.; Blau, W.J.; Curran, S.A.

2010-01-01

A new class of nanomaterials, namely microbiologically-formed nanorods composed of elemental tellurium [Te(0)] that forms unusual nanocomposites when combined with poly(m-phenylenevinylene-co-2,5-dioctoxy-phenylenevinylene) (PmPV) is described. These bio-nanocomposites exhibit excellent broadband optical limiting at 532 and 1064 nm. Nonlinear scattering, originating from the laser induced solvent bubbles and microplasmas, is responsible for this nonlinear behavior. The use of bacterially-formed Te(0) when combined with an organic chemical host (e.g., PmPV) is a new green method of nanoparticle syntheses. This opens the possibilities of using unique, biologically synthesized materials to advance future nanoelectronic and nanophotonic applications. ?? 2009 Elsevier B.V. All rights reserved.

Extraction-spectrophotometric method for silicon determination in high-purity substances. 1. Silicon determination in tellurium

Energy Technology Data Exchange (ETDEWEB)

Shaburova, V P; Yudelevich, I G [AN SSSR, Novosibirsk (USSR). Inst. Neorganicheskoj Khimii

1989-01-01

The extraction-spectrophotometric method for silicon determination in tellurium based on extraction isolation of the base by tributyl phosphate from hydrochloride solutions and with addition of HNO/sub 3/ and spectrophotometric silicon determination using malachite green is developed. The method permits to determine 2x10/sup -1/-3x10/sup -4/ % Si.

The use of masking agents in the determination, by hydride generation and atomic-absorption spectrophotometry, of arsenic, antimony, selenium, tellurium, and bismuth in the presence of noble metals

International Nuclear Information System (INIS)

Kellerman, S.P.

1982-01-01

The effectiveness of thiosemicarbazide, tellurium, and potassium iodide as masking agents to eliminate interferences was assessed. Thiosemicarbazide was found to be effective in eliminating or reducing the interferences on arsenic, antimony, and bismuth, and tellurium reduced the interferences on selenium. The interferences on tellurium could not be eliminated. Arsenic, antimony, selenium, and bismuth were determined in metal sulphide concentrates that were spiked with the noble metals (defined here as gold plus all the platinum-group metals except osmium). The relative standard deviations for arsenic, antimony, bismuth, and selenium were 0,061, 0,017, 0,029, and 0,145 respectively. The values obtained for all the analytes agreed favourably with the preferred values for two in-house reference samples. The laboratory method is detailed in an appendix

Improvement of physical properties of ZnO thin films by tellurium doping

Energy Technology Data Exchange (ETDEWEB)

Sönmezoğlu, Savaş, E-mail: svssonmezoglu@kmu.edu.tr; Akman, Erdi

2014-11-01

Highlights: • We report the synthesis of tellurium-doped zinc oxide (Te–ZnO) thin films using sol–gel method. • Highly c-axis oriented Te-doped ZnO thin films were grown on FTO glasses as substrate. • 1.5% Te-doping ratio could improve the physical properties of ZnO thin films. - Abstract: This investigation addressed the structural, optical and morphological properties of tellurium incorporated zinc oxide (Te–ZnO) thin films. The obtained results indicated that Te-doped ZnO thin films exhibit an enhancement of band gap energy and crystallinity compared with non-doped films. The optical transmission spectra revealed a shift in the absorption edge toward lower wavelengths. X-ray diffraction measurement demonstrated that the film was crystallized in the hexagonal (wurtzite) phase and presented a preferential orientation along the c-axis. The XRD obtained patterns indicate that the crystallite size of the thin films, ranging from 23.9 to 49.1 nm, changed with the Te doping level. The scanning electron microscopy and atomic force microscopy results demonstrated that the grain size and surface roughness of the thin films increased as the Te concentration increased. Most significantly, we demonstrate that it is possible to control the structural, optical and morphological properties of ZnO thin films with the isoelectronic Te-incorporation level.

High performance supercapacitor and non-enzymatic hydrogen peroxide sensor based on tellurium nanoparticles

Directory of Open Access Journals (Sweden)

M. Manikandan

2017-04-01

Full Text Available Tellurium nanoparticles (Te Nps were synthesized by wet chemical method and characterized by XRD, Raman, FESEM, TEM, XPS, UV–Vis and FL. The Nps were coated on graphite foil and Glassy carbon electrode to prepare the electrodes for supercapacitor and biosensor applications. The supercapacitor performance is evaluated in 2 M KOH electrolyte by both Cyclic Voltammetry (CV and galvanostatic charge-discharge method. From charge-discharge method, Te Nps show a specific capacitance of 586 F/g at 2 mA/cm2 and 100 F/g at 30 mA/cm2 as well as an excellent cycle life (100% after 1000 cycles. In addition, the H2O2 sensor performance of Te Nps modified glassy carbon electrode is checked by CV and Chronoamperometry (CA in phosphate buffer solution (PBS. In the linear range of 0.67 to 8.04 μM of hydrogen peroxide (H2O2, Te NPs show a high sensitivity of 0.83 mA mM−1 cm−2 with a correlation coefficient of 0.995. The detection limit is 0.3 μM with a response time less than 5 s. Keywords: Tellurium nanoparticles, Supercapacitor, Biosensor, Hydrogen peroxide

States in 118Sn from 117Sn(d,p) 118Sn at 12 MeV

International Nuclear Information System (INIS)

Frota-Pessoa, E.

1983-01-01

118 Sn energy levels up to = 5.2 MeV excitation energy are studied in the reaction 117 Sn (d,p) 118 Sn. Deuterons had a bombarding energy of 12 MeV. The protons were analized by a magnetic spectrograph. The detector was nuclear emulsion and the resolution in energy about 10 KeV. The distorted-wave analysis was used to determine l values and spectroscopic strengths. Centers of gravity and the sums of reduced spectroscopic factors are presented for the levels when it was possible to determine the S' value. 66 levels of excitation energy were found which did not appear in previous 117 Sn (d,p) reactions. 40 levels were not found previously in any reaction giving 118 Sn. The results are compared with the known ones. (Author) [pt

Intrinsic two-dimensional states on the pristine surface of tellurium

Science.gov (United States)

Li, Pengke; Appelbaum, Ian

2018-05-01

Atomic chains configured in a helical geometry have fascinating properties, including phases hosting localized bound states in their electronic structure. We show how the zero-dimensional state—bound to the edge of a single one-dimensional helical chain of tellurium atoms—evolves into two-dimensional bands on the c -axis surface of the three-dimensional trigonal bulk. We give an effective Hamiltonian description of its dispersion in k space by exploiting confinement to a virtual bilayer, and elaborate on the diminished role of spin-orbit coupling. These intrinsic gap-penetrating surface bands were neglected in the interpretation of seminal experiments, where two-dimensional transport was otherwise attributed to extrinsic accumulation layers.

33 CFR 118.90 - Bridges crossing channel obliquely.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Bridges crossing channel obliquely. 118.90 Section 118.90 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.90 Bridges crossing channel obliquely. Bridges...

Tellurium Enrichment in Jurassic Coal, Brora, Scotland

Directory of Open Access Journals (Sweden)

Liam Bullock

2017-11-01

Full Text Available Mid-Jurassic pyritic coals exposed at the village of Brora, northern Scotland, UK, contain a marked enrichment of tellurium (Te relative to crustal mean, average world coal compositions and British Isles Carboniferous coals. The Te content of Brora coal pyrite is more than one order of magnitude higher than in sampled pyrite of Carboniferous coals. The Te enrichment coincides with selenium (Se and mercury (Hg enrichment in the rims of pyrite, and Se/Te is much lower than in pyrites of Carboniferous coals. Initial pyrite formation is attributed to early burial (syn-diagenesis, with incorporation of Te, Se, Hg and lead (Pb during later pyrite formation. The source of Te may have been a local hydrothermal system which was responsible for alluvial gold (Au in the region, with some Au in Brora headwaters occurring as tellurides. Anomalous Te is not ubiquitous in coal, but may occur locally, and is detectable by laser ablation inductively coupled plasma-mass spectrometry (LA-ICP-MS.

7 CFR 15.118 - Cross-examination.

Science.gov (United States)

2010-01-01

... 7 Agriculture 1 2010-01-01 2010-01-01 false Cross-examination. 15.118 Section 15.118 Agriculture Office of the Secretary of Agriculture NONDISCRIMINATION Rules of Practice and Procedure for Hearings...-examination. Cross-examination will be limited to the scope of direct examination and matters at issue in the...

Effect of tellurium on viscosity and liquid structure of GaSb melts

Energy Technology Data Exchange (ETDEWEB)

Ji Leilei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China); Geng Haoran [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)], E-mail: mse_genghr@ujn.edu.cn; Sun Chunjing [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Teng Xinying; Liu Yamei [School of Material Science and Engineering, Jinan University, Jinan 250022 (China)

2008-04-03

The behavior of GaSb melt with tellurium addition was investigated using viscometer and differential scanning calorimetry (DSC). Normally, the viscosity of all melts measured decreased with the increasing temperature. However, anomalous transition points were observed in the temperature dependence of viscosity for Ga-Sb-Te system. Corresponded with the abnormal points on the viscosity-temperature curves, there were thermal effect peaks on the DSC curves. Furthermore, viscous activation energy and flow units of these melts and their structural features were discussed in this paper.

Ecological aspects of selenium and tellurium in human and animal health

Energy Technology Data Exchange (ETDEWEB)

Frost, D V; Ingvoldstad, D

1975-01-01

Animal and human studies indicate that selenium inadequacy, in part, underlies various chronic diseases. Epidemiologic evidence suggests that cancer and heart disease are most common where ambient Se availability is low. Plant Se uptake and Se blood levels are inverse to human cancer mortality. As the active group in glutathione peroxidase, Se/sup -2/ inhibits aberrant oxidations which lead to chronic diseases. It binds heavy metals, and with tocopherol maintains tissue integrity. Sulfur dioxide fallout from the atmosphere, resulting from fossil fuel burning, may diminish the nutritional availability of selenium by diminishing plant uptake. Intensive ruminant grazing returns unavailable Se/sup 0/ to soils. Trimethyl selenium ion, as excreted by animals, also appears to be unavailable to plants. Modern fertilization practices and the effect of buildup of sulfates in the soil, due to acid rains, both appear to lessen the availability of Se to plants. SeO/sub 2/ added to the atmosphere from combustion and volcanic activity react with SO/sub 2/ to yield Se/sup 0/. This is presumed to fall out as particles from the air. How traces of Se are otherwise carried in air, explaining its enrichment in some areas, is unknown. The New Zealand experience with Se inadequacy in animals and man may be repeated in other parts of the world. Se inadequacy is far more of a human health problem than Se toxicity. There are no known adverse health effects from tellurium, other than tellurium breath. 164 references, 5 figures, 3 tables.

33 CFR 118.70 - Lights on swing bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on swing bridges. 118.70 Section 118.70 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.70 Lights on swing bridges. (a) Swing span lights on through bridges. Each...

33 CFR 118.80 - Lights on bascule bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on bascule bridges. 118.80 Section 118.80 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.80 Lights on bascule bridges. (a) Lift span lights. Each lift span of...

33 CFR 118.65 - Lights on fixed bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on fixed bridges. 118.65 Section 118.65 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.65 Lights on fixed bridges. (a) Each fixed bridge span over a navigable...

Synthesis of Novel E-2-Chlorovinyltellurium Compounds Based on the Stereospecific Anti-addition of Tellurium Tetrachloride to Acetylene

Directory of Open Access Journals (Sweden)

Svetlana V. Amosova

2012-05-01

Full Text Available The reaction of tellurium tetrachloride with acetylene proceeds in a stereospecific anti-addition manner to afford the novel products E-2-chlorovinyltellurium trichloride and E,E-bis(2-chlorovinyltellurium dichloride. Reaction conditions for the selective preparation of each of these products were found. The latter was obtained in 90% yield in CHCl₃ under a pressure of acetylene of 10–15 atm, whereas the former product was formed in up to 72% yield in CCl₄ under a pressure of acetylene of 1–3 atm. Synthesis of the previously unknown E,E-bis(2-chlorovinyl telluride, E,E-bis(2-chlorovinyl ditelluride, E-2-chlorovinyl 1,2,2-trichloroethyl telluride and E,E-bis(2-chlorovinyl-tellurium dibromide is described.

The application of three-phase liquid-liquid extraction to the analysis of bismuth and tellurium in sulphide concentrates

International Nuclear Information System (INIS)

Nicholas, D.J.

1976-01-01

An extraction system consisting of one aqueous and two organic phases is described. Diantipyrylmethane (DAM) is used as the extractant for bismuth and tellurium, which are extracted into the smaller of the two organic phases from nitric acid and perchloric acid respectively. The extraction efficiency is in the range of 90 to 95 per cent, compensation for incomplete extraction being made by the technique of standard addition. Copper, lead, and zinc are not extracted in either procedure. When the solutions contain high concentrations of iron, thioglycolic acid is used as a masking agent for iron in the extraction of bismuth. Atomic-absorption spectrophotometry is used for the analysis of the third phase after it has been diluted with methanol. The precision for bismuth and tellurium is in the range of 3 to 4 per cent. The accuracy, as ascertained from comparative analyses of sulphide concentrates, is good

Tellurium stable isotope fractionation in chondritic meteorites and some terrestrial samples

Science.gov (United States)

Fehr, Manuela A.; Hammond, Samantha J.; Parkinson, Ian J.

2018-02-01

New methodologies employing a 125Te-128Te double-spike were developed and applied to obtain high precision mass-dependent tellurium stable isotope data for chondritic meteorites and some terrestrial samples by multiple-collector inductively coupled plasma mass spectrometry. Analyses of standard solutions produce Te stable isotope data with a long-term reproducibility (2SD) of 0.064‰ for δ130/125Te. Carbonaceous and enstatite chondrites display a range in δ130/125Te of 0.9‰ (0.2‰ amu-1) in their Te stable isotope signature, whereas ordinary chondrites present larger Te stable isotope fractionation, in particular for unequilibrated ordinary chondrites, with an overall variation of 6.3‰ for δ130/125Te (1.3‰ amu-1). Tellurium stable isotope variations in ordinary chondrites display no correlation with Te contents or metamorphic grade. The large Te stable isotope fractionation in ordinary chondrites is likely caused by evaporation and condensation processes during metamorphism in the meteorite parent bodies, as has been suggested for other moderately and highly volatile elements displaying similar isotope fractionation. Alternatively, they might represent a nebular signature or could have been produced during chondrule formation. Enstatite chondrites display slightly more negative δ130/125Te compared to carbonaceous chondrites and equilibrated ordinary chondrites. Small differences in the Te stable isotope composition are also present within carbonaceous chondrites and increase in the order CV-CO-CM-CI. These Te isotope variations within carbonaceous chondrites may be due to mixing of components that have distinct Te isotope signatures reflecting Te stable isotope fractionation in the early solar system or on the parent bodies and potentially small so-far unresolvable nucleosynthetic isotope anomalies of up to 0.27‰. The Te stable isotope data of carbonaceous and enstatite chondrites displays a general correlation with the oxidation state and hence might

46 CFR 118.300 - Fire pumps.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Fire pumps. 118.300 Section 118.300 Shipping COAST GUARD... Fire pumps. (a) A self priming, power driven fire pump must be installed on each vessel. (b) On a..., the fire pump must be capable of delivering a single hose stream from the highest hydrant, through the...

Characterization of the genetic locus responsible for the production of ABP-118, a novel bacteriocin produced by the probiotic bacterium Lactobacillus salivarius subsp. salivarius UCC118.

Science.gov (United States)

Flynn, Sarah; van Sinderen, Douwe; Thornton, Gerardine M; Holo, Helge; Nes, Ingolf F; Collins, J Kevin

2002-04-01

ABP-118, a small heat-stable bacteriocin produced by Lactobacillus salivarius subsp. salivarius UCC118, a strain isolated from the ileal-caecal region of the human gastrointestinal tract, was purified to homogeneity. Using reverse genetics, a DNA fragment specifying part of ABP-118 was identified on a 10769 bp chromosomal region. Analysis of this region revealed that ABP-118 was a Class IIb two-peptide bacteriocin composed of Abp118alpha, which exhibited the antimicrobial activity, and Abp118beta, which enhanced the antimicrobial activity. The gene conferring strain UCC118 immunity to the action of ABP-118, abpIM, was identified downstream of the abp118beta gene. Located further downstream of abp118beta, several ORFs were identified whose deduced proteins resembled those of proteins involved in bacteriocin regulation and secretion. Heterologous expression of ABP-118 was achieved in Lactobacillus plantarum, Lactococcus lactis and Bacillus cereus. In addition, the abp118 locus encoded an inducing peptide, AbpIP, which was shown to play a role in the regulation of ABP-118 production. This novel bacteriocin is, to the authors' knowledge, the first to be isolated from a known human probiotic bacterium and to be characterized at the genetic level.

The influence of composition of fluoride electrolytes and conditions of the electrodeposition on some properties of tellurium

International Nuclear Information System (INIS)

Bugelis, V.M.; Kum, G.N.; Abrarov, O.A.; Madumarov, A.; Navalikhin, L.V.; Ajnakulov, Eh.B.

1981-01-01

Effect of electrolytic bath content, cathode current density, illumination and temperature on specific resistance, photosensitivity, structure and chemical purity of plated tellurium coatings is studied. Deposition is realized from moderately acid fluoride electrolytes at the constant temperature with a platinum working electrode. X-ray studies of precipitates obtained are carried out

Evaluated phase diagrams of binary metal-tellurium systems of the D-block transition elements

International Nuclear Information System (INIS)

Chattopadhyay, G.; Bharadwaj, S.R.

1989-01-01

The binary phase diagrams of metal-tellurium systems for twenty seven d-block transition elements have been critically evaluated. Complete phase diagrams are presented for the elements, chromium, manganese, iron, cobalt, nickel, copper, molybdenum, palladium, silver, lanthanum, platinum and gold, whereas, for scandium, titanium, vanadium, yttrium, zirconium, niobium, technitium, ruthenium, rhodium, hafnium, tantalum, tungsten , rhenium, osmium and iridium, the phase diagrams are incomplete and tentative. (author). 20 refs., 27 tabs., 27 figs

Thermodynamic assessment of the palladium-tellurium (Pd-Te) system

International Nuclear Information System (INIS)

Gosse, S.; Gueneau, C.

2011-01-01

Among the fission products formed in nuclear fuels, the platinum-group metal palladium and the chalcogen element tellurium exhibit strong interaction. It is therefore of interest to be able to predict the chemical equilibria involving the Pd and Te fission products. A thermodynamic assessment is carried out using the Calphad (Calculation of Phase Diagram) method to investigate the behaviour of Pd-Te alloy system in nuclear fuels under irradiation and under waste disposal conditions. The Pd-Te binary description was optimized using experimental data found in literature including thermodynamic properties and phase diagram data. To validate the calculated phase diagram and thermodynamic properties, the results are compared with data from the literature. Both calculated and experimental phase diagrams and thermodynamic properties are in good agreement in the whole Pd-Te composition range. (authors)

Investigation of evaporation characteristics of polonium and its lighter homologues selenium and tellurium from liquid Pb-Bi-eutecticum

CERN Document Server

Neuhausen, J; Eichler, B

2004-01-01

The evaporation behaviour of polonium and its lighter homologues selenium and tellurium dissolved in liquid Pb-Bi-eutecticum (LBE) has been studied at various temperatures in the range from 482 K up to 1330 K under Ar/H2 and Ar/H2O-atmospheres using γ-ray spectroscopy. Polonium release in the temperature range of interest for technical applications is slow. Within short term (1h) experiments measurable amounts of polonium are evaporated only at temperatures above 973 K. Long term experiments reveal that a slow evaporation of polonium occurs at temperatures around 873 K resulting in a fractional polonium loss of the melt around 1% per day. Evaporation rates of selenium and tellurium are smaller than those of polonium. The presence of H2O does not enhance the evaporation within the error limits of our experiments. The thermodynamics and possible reaction pathways involved in polonium release from LBE are discussed.

Effect of sample preparation methods on photometric determination of the tellurium and cobalt content in the samples of copper concentrates

Directory of Open Access Journals (Sweden)

Viktoriya Butenko

2016-03-01

Full Text Available Methods of determination of cobalt and nickel in copper concentrates currently used in factory laboratories are very labor intensive and time consuming. The limiting stage of the analysis is preliminary chemical sample preparation. Carrying out the decomposition process of industrial samples with concentrated mineral acids in open systems does not allow to improve the metrological characteristics of the methods, for this reason improvement the methods of sample preparation is quite relevant and has a practical interest. The work was dedicated to the determination of the optimal conditions of preliminary chemical preparation of copper concentrate samples for the subsequent determination of cobalt and tellurium in the obtained solution using tellurium-spectrophotometric method. Decomposition of the samples was carried out by acid dissolving in individual mineral acids and their mixtures by heating in an open system as well as by using ultrasonification and microwave radiation in a closed system. In order to select the optimal conditions for the decomposition of the samples in a closed system the phase contact time and ultrasonic generator’s power were varied. Intensification of the processes of decomposition of copper concentrates with nitric acid (1:1, ultrasound and microwave radiation allowed to transfer quantitatively cobalt and tellurium into solution spending 20 and 30 min respectively. This reduced the amount of reactants used and improved the accuracy of determination by running the process in strictly identical conditions.

9 CFR 118.4 - Seizure and condemnation.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Seizure and condemnation. 118.4... AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS DETENTION; SEIZURE AND CONDEMNATION § 118.4 Seizure and condemnation. Any biological product which is prepared, sold, bartered...

46 CFR 171.118 - Automatic ventilators and side ports.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Automatic ventilators and side ports. 171.118 Section 171.118 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY... Bulkhead or Weather Deck § 171.118 Automatic ventilators and side ports. (a) An automatic ventilator must...

LIGHT INDUCED TELLURIUM ENRICHMENT ON CDZNTE CRYSTAL SURFACES DETECTED BY RAMAN SPECTROSCOPY

International Nuclear Information System (INIS)

Hawkins, S; Eliel Villa-Aleman, E; Martine Duff, M; Douglas Hunter, D

2007-01-01

Synthetic CdZnTe or 'CZT' crystals can be grown under controlled conditions to produce high quality crystals to be used as room temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro Raman spectroscopy. The growth of Te rich areas on the surface was induced by low powered lasers. The growth was observed versus time with low power Raman scattering and was observed immediately under higher power conditions. The detector response was also measured after induced Te enrichment

21 CFR 118.6 - Egg testing for Salmonella Enteritidis (SE).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Egg testing for Salmonella Enteritidis (SE). 118.6... (CONTINUED) FOOD FOR HUMAN CONSUMPTION PRODUCTION, STORAGE, AND TRANSPORTATION OF SHELL EGGS § 118.6 Egg... age required by § 118.4(a) is positive, you must divert eggs to treatment (defined in § 118.3) for the...

Equilibrium evaporation test of lead-bismuth eutectic and of tellurium in lead-bismuth

International Nuclear Information System (INIS)

Ohno, Shuji; Nishimura, Masahiro; Hamada, Hirotsugu; Miyahara, Shinya; Sasa, Toshinobu; Kurata, Yuji

2005-01-01

A series of equilibrium evaporation experiment was performed to acquire the essential and the fundamental knowledge about the transfer behavior of lead-bismuth eutectic (LBE) and impurity tellurium in LBE from liquid to gas phase. The experiments were conducted using the transpiration method in which saturated vapor in an isothermal evaporation pot was transported by inert carrier gas and collected outside of the pot. The size of the used evaporation pot is 8 cm inner diameter and 15 cm length. The weight of the LBE pool in the pot is about 500 g. The investigated temperature range was 450degC to 750degC. From this experiment and discussion using the data in literature, we have obtained several instructive and useful data on the LBE evaporation behavior such as saturated vapor pressure of LBE, vapor concentration of Pb, Bi and Bi 2 in LBE saturated gas phase, and activity coefficient of Pb in the LBE. The LBE vapor pressure equation is represented as the sum of Pb, Bi and Bi 2 vapor in the temperature range between 550degC and 750degC as logP[Pa]=10.2-10100/T[k]. The gas-liquid equilibrium partition coefficient of tellurium in LBE is in the range of 10 to 100, with no remarkable temperature dependency between 450degC and 750degC. This research was founded by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). (author)

Facile Hydrothermal Synthesis of Tellurium Nanostructures for Solar Cells

Directory of Open Access Journals (Sweden)

M. Panahi-Kalamuei

2014-10-01

Full Text Available Tellurium (Te nanostructures have been successfully synthesized via a simple hydrothermal methodfrom the reaction of a TeCl4 aqueous solution with thioglycolic acid (TGA as a reductant. TGA can be easily oxidized to the corresponding disulfide [SCH2CO2H]2, which in turn can reduce TeCl4 to Te. The obtained Te was characterized by XRD, SEM, EDS, and DRS. The effect of reducing agent on morphology and size of the products were also studied. Additionally, Te thin film was deposited on the FTO-TiO2 by Dr- blading then employed to solar cell application and measured open circuit voltage (Voc, short circuit current (Isc, and fill factor (FF were determined as well. The studies showed that particle morphology and sizes play crucial role on solar cell efficiencies.

10 CFR 1.18 - Advisory Committee on Nuclear Waste.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Advisory Committee on Nuclear Waste. 1.18 Section 1.18... Panels, Boards, and Committees § 1.18 Advisory Committee on Nuclear Waste. The Advisory Committee on Nuclear Waste (ACNW) provides advice to the Commission on all aspects of nuclear waste management, as...

Determination of gold, indium, tellurium and thallium in the same sample digest of geological materials by atomic-absorption spectroscopy and two-step solvent extraction

Science.gov (United States)

Hubert, A.E.; Chao, T.T.

1985-01-01

A rock, soil, or stream-sediment sample is decomposed with hydrofluoric acid, aqua regia, and hydrobromic acid-bromine solution. Gold, thallium, indium and tellurium are separated and concentrated from the sample digest by a two-step MIBK extraction at two concentrations of hydrobromic add. Gold and thallium are first extracted from 0.1M hydrobromic acid medium, then indium and tellurium are extracted from 3M hydrobromic acid in the presence of ascorbic acid to eliminate iron interference. The elements are then determined by flame atomic-absorption spectrophotometry. The two-step solvent extraction can also be used in conjunction with electrothermal atomic-absorption methods to lower the detection limits for all four metals in geological materials. ?? 1985.

Evaluation of the Content of Antimony, Arsenic, Bismuth, Selenium, Tellurium and Their Inorganic Forms in Commercially Baby Foods.

Science.gov (United States)

Ruiz-de-Cenzano, M; Rochina-Marco, A; Cervera, M L; de la Guardia, M

2017-12-01

Baby foods, from the Spanish market and prepared from meat, fish, vegetables, cereals, legumes, and fruits, were analyzed to obtain the concentration of antimony (Sb), arsenic (As), bismuth (Bi), and tellurium (Te) as toxic elements and selenium (Se) as essential element. An analytical procedure was employed based on atomic fluorescence spectroscopy which allowed to obtain accurate data at low levels of concentration. Values of 14 commercial samples, expressed in nanograms per gram fresh weight, ranged for Sb 0.66-6.9, As 4.5-242, Te 1.35-2.94, Bi 2.18-4.79, and Se 5.4-109. Additionally, speciation studies were performed based on data from a non-chromatographic screening method. It was concluded that tellurium and bismuth were mainly present as inorganic forms and selenium as organic form, and antimony and arsenic species depend on the ingredients of each baby food. Risk assessment considerations were made by comparing dietary intake of the aforementioned elements through the consumption of one baby food portion a day and recommended or tolerable guideline values.

41 CFR 102-118.10 - What is a transportation audit?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What is a transportation audit? 102-118.10 Section 102-118.10 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION...

41 CFR 102-118.15 - What is a transportation payment?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What is a transportation payment? 102-118.15 Section 102-118.15 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION...

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

Energy Technology Data Exchange (ETDEWEB)

Simon, F.-G., E-mail: franz-georg.simon@bam.de [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany); Holm, O.; Berger, W. [BAM Federal Institute for Materials Research and Testing, Division 4.3 Contaminant Transfer and Environmental Technologies, Unter den Eichen 87, 12205 Berlin (Germany)

2013-04-15

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources.

Resource recovery from urban stock, the example of cadmium and tellurium from thin film module recycling

International Nuclear Information System (INIS)

Simon, F.-G.; Holm, O.; Berger, W.

2013-01-01

Highlights: ► The semiconductor layer on thin-film photovoltaic modules can be removed from the glass-plate by vacuum blast cleaning. ► The separation of blasting agent and semiconductor can be performed using flotation with a valuable yield of 55%. ► PV modules are a promising source for the recovery of tellurium in the future. - Abstract: Raw material supply is essential for all industrial activities. The use of secondary raw material gains more importance since ore grade in primary production is decreasing. Meanwhile urban stock contains considerable amounts of various elements. Photovoltaic (PV) generating systems are part of the urban stock and recycling technologies for PV thin film modules with CdTe as semiconductor are needed because cadmium could cause hazardous environmental impact and tellurium is a scarce element where future supply might be constrained. The paper describes a sequence of mechanical processing techniques for end-of-life PV thin film modules consisting of sandblasting and flotation. Separation of the semiconductor material from the glass surface was possible, however, enrichment and yield of valuables in the flotation step were non-satisfying. Nevertheless, recovery of valuable metals from urban stock is a viable method for the extension of the availability of limited natural resources

Determination of tellurium by hydride generation with in situ trapping flame atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Matusiewicz, H.; Krawczyk, M. [Politechn Poznanska, Poznan (Poland)

2007-03-15

The analytical performance of coupled hydride generation - integrated atom trap (HG-IAT) atomizer flame atomic absorption spectrometry (FAAS) system was evaluated for determination of Te in reference material (GBW 07302 Stream Sediment), coal fly ash and garlic. Tellurium, using formation of H{sub 2}Te vapors, is atomized in air-acetylene flame-heated IAT. A new design HG-IAT-FAAS hyphenated technique that would exceed the operational capabilities of existing arrangernents (a water-cooled single silica tube, double-slotted quartz tube or an 'integrated trap') was investigated. An improvement in detection limit was achieved compared with using either of the above atom trapping techniques separately. The concentration detection limit, defined as 3 times the blank standard deviation (3{sigma}), was 0.9 ng mL{sup -1} for Te. For a 2 min in situ preconcentration time (sample volume of 2 mL), sensitivity enhancement compared to flame AAS, was 222 fold, using the hydride generation atom trapping technique. The sensitivity can be further improved by increasing the collection time. The precision, expressed as RSD, was 7.0% (n = 6) for Te. The accuracy of the method was verified using a certified reference material (GBW 07302 Stream Sediment) by aqueous standard calibration curves. The measured Te contents of the reference material was in agreement with the information value. The method was successfully applied to the determination of tellurium in coal fly ash and garlic.

Test of irradiation of tellurium oxide for obtaining iodine-131 by dry distillation

International Nuclear Information System (INIS)

Alanis M, J.

2003-07-01

With the purpose of optimizing to the maximum independently the work of the reactor of those mathematical calculations of irradiation that are already optimized, now it corresponds to carry out irradiation tests in the different positions with their respective neutron fluxes that it counts the reactor for samples irradiation. Then, it is necessary to carry out the irradiation of the tellurium dioxide through cycles, with the purpose of observing the activity that it goes accumulating in each cycle and this way to obtain an activity of the Iodine-131 obtained when finishing the last cycle. (Author)

33 CFR 118.110 - Daymarks and lateral lighting on bridges.

Science.gov (United States)

2010-07-01

... bridges. 118.110 Section 118.110 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.110 Daymarks and lateral lighting on bridges. (a... through bridges with U.S. aids to navigation system lateral marks and lights installed on the...

28 CFR 0.118 - Office of Chief Administrative Hearing Officer.

Science.gov (United States)

2010-07-01

... Officer. 0.118 Section 0.118 Judicial Administration DEPARTMENT OF JUSTICE ORGANIZATION OF THE DEPARTMENT OF JUSTICE Executive Office for Immigration Review § 0.118 Office of Chief Administrative Hearing... Law Judges in performance of their duties in accordance with 8 U.S.C. 1324 A and B. ...

42 CFR 401.118 - Deletion of identifying details.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Deletion of identifying details. 401.118 Section 401.118 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... Deletion of identifying details. When CMS publishes or otherwise makes available an opinion or order...

Characterization of Endogenous Plasmids from Lactobacillus salivarius UCC118▿ †

OpenAIRE

Fang, Fang; Flynn, Sarah; Li, Yin; Claesson, Marcus J.; van Pijkeren, Jan-Peter; Collins, J. Kevin; van Sinderen, Douwe; O'Toole, Paul W.

2008-01-01

The genome of Lactobacillus salivarius UCC118 comprises a 1.83-Mb chromosome, a 242-kb megaplasmid (pMP118), and two smaller plasmids of 20 kb (pSF118-20) and 44 kb (pSF118-44). Annotation and bioinformatic analyses suggest that both of the smaller plasmids replicate by a theta replication mechanism. Furthermore, it appears that they are transmissible, although neither possesses a complete set of conjugation genes. Plasmid pSF118-20 encodes a toxin-antitoxin system composed of pemI and pemK h...

Selenium Se and tellurium Te

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for determining selenium and tellurium in various objects are presented. The bichromatometric determination of Te in cadmium, zinc and mercury tellurides is based on oxidation of Te(4) to (6) in H 2 SO 4 with potassium bichromate. In steels, Te is determined photometrically with the aid of KI. The determination is hindered by Fe(3), Cu(2), Bi(3) and Se(4) ions, which must be separated. The extraction-photometric determination of Te in native sulfur is carried out with the aid of 5-mercapto-3-(naphthyl-2)-1,3,4-thiadiazolthione-2 (pH=4.8-5.0). The dyed complex is readily extracted with chloroform and benzene. The spectrophotometric determination of Te in selenium is performed with the aid of 3,5-diphenylpyrazoline-1-dithiocarbamate of sodium. Te is determined in commercial indium, arsenic and their semiconductor compounds photometrically with the aid of copper diethyldithiocarbamate. The method permits determining 5x10 -5 % Te in a weighed amount of 0.5 g. The chloride complex of Te(4) with diantipyriodolpropylmethane is quantitatively extracted with dichloroethane from hydrochloric acid solutions. Thus, any amounts of Te can be separated from Se and determined photometrically. The extraction-photometric determination of Te in commercial lead and bismuth is carried out with the aid of pyrazolone derivatives, in commercial copper with the aid of diantipyridolpropylmethane, and in ores (more than 0.01% Te) with the aid of bismuthol 2. Also described is the extraction-polarographic determination of Te in sulfide ores

Characterization of Endogenous Plasmids from Lactobacillus salivarius UCC118▿ †

Science.gov (United States)

Fang, Fang; Flynn, Sarah; Li, Yin; Claesson, Marcus J.; van Pijkeren, Jan-Peter; Collins, J. Kevin; van Sinderen, Douwe; O'Toole, Paul W.

2008-01-01

The genome of Lactobacillus salivarius UCC118 comprises a 1.83-Mb chromosome, a 242-kb megaplasmid (pMP118), and two smaller plasmids of 20 kb (pSF118-20) and 44 kb (pSF118-44). Annotation and bioinformatic analyses suggest that both of the smaller plasmids replicate by a theta replication mechanism. Furthermore, it appears that they are transmissible, although neither possesses a complete set of conjugation genes. Plasmid pSF118-20 encodes a toxin-antitoxin system composed of pemI and pemK homologs, and this plasmid could be cured when PemI was produced in trans. The minimal replicon of pSF118-20 was determined by deletion analysis. Shuttle vector derivatives of pSF118-20 were generated that included the replication region (pLS203) and the replication region plus mobilization genes (pLS208). The plasmid pLS203 was stably maintained without selection in Lactobacillus plantarum, Lactobacillus fermentum, and the pSF118-20-cured derivative strain of L. salivarius UCC118 (strain LS201). Cloning in pLS203 of genes encoding luciferase and green fluorescent protein, and expression from a constitutive L. salivarius promoter, demonstrated the utility of this vector for the expression of heterologous genes in Lactobacillus. This study thus expands the knowledge base and vector repertoire of probiotic lactobacilli. PMID:18390685

Formation of defects in tellurium at various levels of gravitation

International Nuclear Information System (INIS)

Parfen'ev, R.V.; Farbshtejn, I.I.; Shul'pina, I.L.; Yakimov, S.V.; Shalimov, V.P.; Turchaninov, A.M.

2002-01-01

One investigated into effect of gravitation conditions during tellurium crystallization (ranging from microgravitation up to increased gravitation - 5g 0 ) on concentration of neutral (N D ) and electrically active (N AD ) acceptor structure defects in specimens grown both under complete remelting of parent ingot and under directed recrystallization of ingot with inoculation. N AD and N D concentrations and their distribution along the specimen depth were determined on the basis of analysis of electrical characteristics (conductivity and the Hall effect) measured along ingots within 1.6-300 K temperature range. The results were compared with characteristics of specimens grown following the similar program under normal conditions. At complete remelting under microgravitation one detected attributes of strong supercooling and spontaneous crystallization, as well as, of specimen resistance oscillation by its depth caused by N D modulation [ru

Use of Iodine-131 to Tellurium-132 Ratios for Assessing the Relationships between Human Inhaled Radioactivity and Environmental Monitoring after the Accident in Fukushima

Directory of Open Access Journals (Sweden)

Koji Uchiyama

2018-03-01

Full Text Available Significant differences in findings were seen between the intake amounts of iodine-131 that were derived from direct measurements and the estimated intake from environmental monitoring data at the Fukushima accident. To clarify these discrepancies, we have investigated the iodine-131 and tellurium-132 body burdens of five human subjects, who after being exposed to a radioactive plume, underwent 21.5 h whole body counter measurements at Fukui Prefectural Hospital, so clear intake scenario and thyroid counter measurement data were available. To determine the iodine-131 and tellurium-132 body burdens, we introduced a new method of whole body counter calibration composed of a self-consistent approach with the time-dependent correction efficiency factors concept. The ratios of iodine-131 to tellurium-132, ranging from 0.96 ± 0.05 to 2.29 ± 0.38, were consistent with results of the environmental measurements. The 24 h iodine uptake values ranging from 12.1–16.0% were within euthyroid range in Japanese people. These results suggest, even if the relatively low thyroid iodine uptake in the Japanese population was taken into consideration, that there is no doubt about the consistency between direct measurements and environmental monitoring data. Adequate intake scenario is suggested to be principally important to estimate the inhaled radioactivity in areas in or around nuclear accidents.

Exploratory studies of element substitutions in synthetic tetrahedrite. Part II. Selenium and tellurium as anions in Zn-Fe tetrahedrites

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

1999-01-01

-free) compositons do not materialize. The substituted Se tetrahedrite coexists with Cu3SbSe3, (iron-bearing) Cu2-xSe, Cu3SbSe4 plus/minus low Zn-sulfide melt. Selenium does not adopt the role of cation and tellurium that of anion in the tetrahedrite structure. The explanation of the severely restricted composition...

The effect of hydrostatic pressure on the anomalous sign reversal of the Hall coefficient in tellurium

International Nuclear Information System (INIS)

Balynas, V.; Dobrovolskis, Z.; Krotkus, A.; Hoerstel, W.

1981-01-01

In order to obtain information about the pressure behaviour of the higher lying second conduction band the dependences of the Hall coefficient of single crystalline tellurium on temperature (300 to 500 K) have been measured at atmospheric pressure and hydrostatic pressures of 500 and 800 MPa. The separation between the two conduction bands in Te decreases with increasing pressure. The anomalous sign reversal of the Hall coefficient can be well explained by a double-conduction band model

Revision and extension to the analysis of the third spectrum of tellurium: Te III

International Nuclear Information System (INIS)

Tauheed, A.; Naz, A.

2011-01-01

The spectrum of doubly ionized tellurium atom (Te III) has been investigated in the vacuum ultraviolet wavelength region. The ground configuration of Te III is 5s 2 5p 2 and the excited configurations are of the type 5s 2 5p nl. The core excitation leads to a 5s5p 3 configuration. Cowan's multi-configuration interaction code was utilized to predict the ion structure. The observed spectrum of tellurium was recorded on a 3-m normal incidence vacuum spectrograph of Antigonish Laboratory (Canada) in the wavelength region of 300 - 2000 A by using a triggered spark light source for the excitation of the spectrum. The 5s 2 5p 2 - [ 5s 2 5p (5d + 6d + 7d + 6s + 7s + 8s) + 5s5p 3 ] transition array has been analyzed. Previously reported levels by Joshi et al have been confirmed while the older analysis by Crooker and Joshi has been revised and extended to include the 5s 2 5p (5d, 6d, 7d, 6s,7s, 8s) and 5s5p 3 configurations. Least-squares- fitted parametric calculations were used to interpret the final results. One hundred and fifty spectral lines have been identified to establish 60 energy levels. Our wavelength accuracy for unblended and sharp lines is better than ±0.005 A. The ionization potential of Te III was found to be 224550 ± 300 cm -1 (27.841 ± 0.037eV).

47 CFR 25.118 - Modifications not requiring prior authorization.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Modifications not requiring prior authorization. 25.118 Section 25.118 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses General Application Filing Requirements § 25...

Validation of a new design of tellurium dioide-irradiated target

Energy Technology Data Exchange (ETDEWEB)

Fllaoui, Aziz; Ghamad, Younes; Zoubir, Brahim; Ayaz, Zinel Abidine; El Morabiti, Aissam; Amayoud, Hafid [Centre National de l' Energie des Sciences et des Techniques Nucleaires, Rabat (Morocco); Chakir, El Mahjoub [Nuclear Physics Department, University Ibn Toufail, Kenitra (Morocco)

2016-10-15

Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO{sub 2}) material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10 - 4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics). To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600 .deg. C with the appearance of deformations on lids beyond 450 .deg. C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes-convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week) at 1.5 MW. The results show that the irradiated targets are

Validation of a New Design of Tellurium Dioxide-Irradiated Target

Directory of Open Access Journals (Sweden)

Aziz Fllaoui

2016-10-01

Full Text Available Production of iodine-131 by neutron activation of tellurium in tellurium dioxide (TeO2 material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gas welding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ≤ 10−4 mbr.L/s, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics. To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to 600°C with the appearance of deformations on lids beyond 450°C. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes—convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from 4 hours of irradiation at a power level of 0.5 MW up to 35 hours (7 h/d for 5 days a week at 1.5 MW. The results show that the irradiated targets are

40 CFR 81.118 - Southwest Missouri Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.118 Section 81.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.118 Southwest Missouri Intrastate Air Quality Control Region. The Southwest Missouri Intrastate Air Quality Control Region consists of the territorial area encompassed by the...

41 CFR 102-118.20 - Who is subject to this part?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Who is subject to this part? 102-118.20 Section 102-118.20 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION...

Light-Induced Tellurium Enrichment on CdZnTe Crystal Surfaces Detected by Raman Spectroscopy

International Nuclear Information System (INIS)

Hawkins, Samantha A.; Villa-Aleman, Eliel; Duff, Martine C.; Hunter, Doug B.; Burger, Arnold; Groza, Michael; Buliga, Vladimir; Black, David R.

2008-01-01

CdZnTe (CZT) crystals can be grown under controlled conditions to produce high-quality crystals to be used as room-temperature radiation detectors. Even the best crystal growth methods result in defects, such as tellurium secondary phases, that affect the crystal's performance. In this study, CZT crystals were analyzed by micro-Raman spectroscopy. The growth of Te rich areas on the surface was induced by low-power lasers. The growth was observed versus time with low-power Raman scattering and was observed immediately under higher-power conditions. The detector response was also measured after induced Te enrichment.

Tellurium rings as electron pair donors in cluster compounds and coordination polymers; Tellurringe als Elektronenpaardonoren in Clusterverbindungen und Koordinationspolymeren

Energy Technology Data Exchange (ETDEWEB)

Guenther, Anja

2011-11-08

In this dissertation novel and already known molecular tellurium rings are presented in cluster compounds and quasi-one-dimensional coordination polymers. The cyclic, homonuclear units are always stabilized by coordination to electron-rich transition metal atoms, with the coordinating tellurium atoms acting as two-electron donors. As a synthesis route, the solid-state reaction in quartz glass vials was used uniformly. In addition to structural determination, the focus was on the characterization of the resulting compounds. For this purpose, resistance measurements were carried out on selected compounds, the magnetic behavior and the thermal degradation reactions were investigated and accompanying quantum chemical calculations were carried out. [German] In dieser Dissertation werden neuartige sowie bereits bekannte molekulare Tellurringe in Clusterverbindungen und quasi-eindimensionalen Koordinationspolymeren vorgestellt. Die Stabilisierung der zyklischen, homonuklearen Einheiten erfolgt dabei stets durch die Koordination an elektronenreiche Uebergangsmetallatome, wobei die koordinierenden Telluratome gegenueber diesen als Zwei-Elektronendonoren fungieren. Als Syntheseroute wurde dabei einheitlich auf die Festkoerperreaktion in Quarzglasampullen zurueckgegriffen. Neben der Strukturaufklaerung stand die Charakterisierung der erhaltenden Verbindungen im Fokus der Arbeit. Dazu wurden an ausgewaehlten Verbindungen Widerstandsmessungen durchgefuehrt, das magnetische Verhalten sowie die thermischen Abbaureaktionen untersucht und begleitende quantenchemische Rechnungen durchgefuehrt.

Determination of tellurium at ultra-trace levels in drinking water by on-line solid phase extraction coupled to graphite furnace atomic absorption spectrometer

International Nuclear Information System (INIS)

Pedro, Juana; Stripekis, Jorge; Bonivardi, Adrian; Tudino, Mabel

2008-01-01

In this paper, two time-based flow injection (FI) separation pre-concentration systems coupled to graphite furnace atomic absorption spectrometry (GFAAS) for tellurium determination are studied and compared. The first alternative involves the pre-concentration of the analyte onto Dowex 1X8 employed as packaging material of a micro-column inserted in the flow system. The second set-up is based on the co-precipitation of tellurium with La(OH) 3 followed by retention onto XAD resins. Both systems are compared in terms of limit of detection, linear range, RSD%, sample throughput, micro-columns lifetime and aptitude for fully automatic operation. The features of the Dowex system are: 37% efficiency of retention and an enhancement factor of 42 for a pre-concentration time of 180 seconds (sample flow rate = 3 ml min -1 ) with acetic acid elution volumes of 80 μl. The detection limit (3 s) is 7 ng l -1 and the relative standard deviation (n = 7200 ng l -1 ) is 5.8%. The analytical performance of the XAD system is: 72% efficiency of retention and an enhancement factor of 25 for a pre-concentration time of 180 s (sample flow rate = 3 ml min -1 ) with nitric acid elution volumes of 300 μl. The detection limit is 66 ng l -1 and the relative standard deviation (n = 7200 ng l -1 ) is 8.3%. Applications to the determination of tellurium in tap water and the validation of the analytical methodology employing SRM 1643e as certified reference material are shown

Challenges in assessment of clean energy supply-chains based on byproduct minerals: A case study of tellurium use in thin film photovoltaics

International Nuclear Information System (INIS)

Bustamante, Michele L.; Gaustad, Gabrielle

2014-01-01

Highlights: • Byproduct mining presents unique challenges to quantifying energy security issues. • This case study shows Te scarcity is closely tied to Cu demand and production. • Material intensity changes over time have a significant impact on projections. • Recycling as a mitigation strategy is shown to have poor short-term results. - Abstract: Transitioning to a sustainable energy supply will be critical to meeting future economic and environmental goals. This transition will require optimizing and commercializing a portfolio of new clean energy technologies. However, many promising clean energy technologies are based on materials with inherent risks in their supply; these risks include scarcity, price volatility, criticality, and other potential supply-chain disruptions. Using tellurium use in CdTe photovoltaics as a case study, this paper presents analysis of some of the key challenges associated with modeling byproduct systems (a supply-chain where a key material is actually a byproduct of extraction of another material, copper in the case of tellurium). This work presents a novel modeling approach; the results of the case study are used to identify potential supply risks facing this clean technology, with a unique focus on sensitivity to changes in the preliminary lifecycle stages. Supply-chain sensitivities are connected with direct environmental impacts to frame the implications in a broader sustainability context and to emphasize the future role of recycling. Ultimately, it was shown that if historical supply and demand trends continue, supply gap conditions will emerge before the end of the current decade. However, improvements in byproduct yield, end-use recycling rate, and end-use material intensity exhibit significant leverage to minimize risk in the energy-critical tellurium supply-chain

Gamma Radiation Dosimetry Using Tellurium Dioxide Thin Film Structures

Directory of Open Access Journals (Sweden)

Olga Korostynska

2002-08-01

Full Text Available Thin films of Tellurium dioxide (TeO2 were investigated for γ-radiation dosimetry purposes. Samples were fabricated using thin film vapour deposition technique. Thin films of TeO2 were exposed to a 60Co γ-radiation source at a dose rate of 6 Gy/min at room temperature. Absorption spectra for TeO2 films were recorded and the values of the optical band gap and energies of the localized states for as-deposited and γ-irradiated samples were calculated. It was found that the optical band gap values were decreased as the radiation dose was increased. Samples with electrical contacts having a planar structure showed a linear increase in current values with the increase in radiation dose up to a certain dose level. The observed changes in both the optical and the electrical properties suggest that TeO2 thin film may be considered as an effective material for room temperature real time γ-radiation dosimetry.

Studies on nickel (II and palladium (II complexes with some tetraazamacrocycles containing tellurium

Directory of Open Access Journals (Sweden)

Rathee Nitu

2012-01-01

Full Text Available The synthesis of 10-membered and 12-membered tellurium containing tetraazamacrocyclic complexes of divalent nickel and palladium by template condensation of diaryltellurium dichlorides, (aryl = p-hydroxyphenyl, 3-methyl-4-hydroxyphenyl, p-methoxyphenyl with 1,2-diaminoethane and 1,3-diaminopropane in the presence of metal dichloride is reported. The resulting complexes have been subjected to elemental analyses, magnetic measurements, electronic absorption, infra-red, and proton magnetic resonance spectral studies. The formation of proposed macrocyclic skeletons and their donor sites have been identified on the basis of spectral studies. Distorted octahedral structure for the nickel complexes in the solid state and squareplanar structure for the palladium complexes have been suggested.

Flavoprotein-mediated tellurite reduction: structural basis and applications to the synthesis of tellurium-containing nanostructures

Directory of Open Access Journals (Sweden)

Mauricio Arenas-Salinas

2016-07-01

Full Text Available The tellurium oxyanion tellurite (TeO32- is extremely harmful for most organisms. It has been suggested that a potential bacterial tellurite resistance mechanism would consist of an enzymatic, NAD(PH-dependent, reduction to the less toxic form elemental tellurium (Te0. To date, a number of enzymes such as catalase, type II NADH dehydrogenase and terminal oxidases from the electron transport chain, nitrate reductases, and dihydrolipoamide dehydrogenase (E3, among others, have been shown to display tellurite-reducing activity. This activity is generically referred to as tellurite reductase (TR. Bioinformatic data resting on some of the abovementioned enzymes enabled the identification of common structures involved in tellurite reduction including vicinal catalytic cysteine residues and the FAD/NAD(P+-binding domain, which is characteristic of some flavoproteins. Along this line, thioredoxin reductase (TrxB, alkyl hydroperoxide reductase (AhpF, glutathione reductase (GorA, mercuric reductase (MerA, NADH: flavorubredoxin reductase (NorW, dihydrolipoamide dehydrogenase, and the putative oxidoreductase YkgC from Escherichia coli or environmental bacteria were purified and assessed for TR activity. All of them displayed in vitro TR activity at the expense of NADH or NADPH oxidation. In general, optimal reducing conditions occurred around pH 9-10 and 37 °C.Enzymes exhibiting strong TR activity produced Te-containing nanostructures (TeNS. While GorA and AhpF generated TeNS of 75 nm average diameter, E3 and YkgC produced larger structures (> 100 nm. Electron-dense structures were observed in cells over-expressing genes encoding TrxB, GorA and YkgC.

33 CFR 118.5 - Penalty for failure to maintain.

Science.gov (United States)

2010-07-01

... States who fails or refuses to maintain such lights and other signals, or to obey any of the lawful rules... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Penalty for failure to maintain. 118.5 Section 118.5 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY...

Tracing Tellurium and Its Nanostructures in Biology.

Science.gov (United States)

Zare, Bijan; Nami, Mohammad; Shahverdi, Ahmad-Reza

2017-12-01

Tellurium (Te) is a semimetal rare element in nature. Together with oxygen, sulfur (S), and selenium (Se), Te is considered a member of chalcogen group. Over recent decades, Te applications continued to emerge in different fields including metallurgy, glass industry, electronics, and applied chemical industries. Along these lines, Te has recently attracted research attention in various fields. Though Te exists in biologic organisms such as microbes, yeast, and human body, its importance and role and some of its potential implications have long been ignored. Some promising applications of Te using its inorganic and organic derivatives including novel Te nanostructures are being introduced. Before discovery and straightforward availability of antibiotics, Te had considered and had been used as an antibacterial element. Antilishmaniasis, antiinflammatory, antiatherosclerotic, and immuno-modulating properties of Te have been described for many years, while the innovative applications of Te have started to emerge along with nanotechnological advances over the recent years. Te quantum dots (QDs) and related nanostructures have proposed novel applications in the biological detection systems such as biosensors. In addition, Te nanostructures are used in labeling, imaging, and targeted drug delivery systems and are tested for antibacterial or antifungal properties. In addition, Te nanoparticles show novel lipid-lowering, antioxidant, and free radical scavenging properties. This review presents an overview on the novel forms of Te, their potential applications, as well as related toxicity profiles.

IPR 118 - Bread wheat cultivar

Directory of Open Access Journals (Sweden)

Carlos Roberto Riede

2007-01-01

Full Text Available Wheat cultivar IPR 118 developed by IAPAR has a good yield potential and is widely adapted. It is earlymaturing and moderately tolerant to shattering and soil aluminum, moderately resistant to leaf rust and presents high glutenstrength for bread-making. The overall yield exceeded controls by 13%.

32 CFR 536.118 - Related statutes for maritime claims.

Science.gov (United States)

2010-07-01

... 32 National Defense 3 2010-07-01 2010-07-01 true Related statutes for maritime claims. 536.118... ACCOUNTS CLAIMS AGAINST THE UNITED STATES Maritime Claims § 536.118 Related statutes for maritime claims... under the AMCSA is not mandatory for causes of action as it is for the SIAA or PVA. (b) Similar maritime...

Influence of the hydrolysis conditions on the properties of tellurium coatings obtained from hydrochloric acid baths

International Nuclear Information System (INIS)

Bigelis, V.M.; Kim, G.N.; Navalikhin, L.V.; Kalanov, M.; Abrarov, O.A.

1982-01-01

The structure of tellurium coatings has been studied using the methods of activational analysis on fast neutrons, roentgenography using DRON-2. The study is carried out in electrolyte 1N TeO 2 +6NHCl+2NH 2 SO 4 at the temperatures 25 and 95 deg C in the range of current densities 10-150 mA/cm 2 with and without mixing. Atomic content of chlorine and oxygen in deposite depending on the electrolyte work is determined. Nicrohardness, density, specific resistance of the coatings investigated are determined

41 CFR 102-118.30 - Are Government corporations bound by this part?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Are Government corporations bound by this part? 102-118.30 Section 102-118.30 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118...

41 CFR 102-118.5 - What is the purpose of this part?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What is the purpose of this part? 102-118.5 Section 102-118.5 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION...

Near threshold electron impact ionization cross section for tellurium atoms

International Nuclear Information System (INIS)

Chipev, F.F.; Chernyshova, I.V.; Kontros, J.E.; Shpenik, O.B.

2004-01-01

Full text: Up today electron-impact ionization is one of the most intensively investigated processes in atomic and molecular physics [1]. These experiments however, are associated with difficulties: high temperatures and densities are required to produce atomic beams and monochromatic intensive electron beams. A crossed electron and atomic beams scattering geometry was employed to measure the ionization efficiency curve for tellurium atoms. Our electron spectrometer comprises two serially mounted hypocycloidal electron energy analyzers [2], the first being the monochromator and the second - the scattered electron analyzer. The whole spectrometer is immersed into the homogenous magnetic field. Great care was taken in selecting the value of the extracting potential at the electrode, mounted normally to the atomic beam direction. By careful choosing this potential as low as possible (∼1.4 V), its influence on the motion of the monochromatized electrons in the collision region was minimized and the full collection of the formed ions was reached. The atom beam was produced using a compact effusion source made of the stainless steel with a microchannel exit to minimise the angular divergency of the beam. The temperature of the microchannel plate was taken about 50 K higher than that of the metal vapour in the heated reservoir. This atomic beam source enabled to produce an atomic beam with the concentration of two orders of magnitude higher than that in the case of a standard effusion source. A typical value of the electron energy spread was 0.15 eV (FWHM) in the 0.1-15 eV energy range. The primary electron beam current was equal to 10 -7 A. Such values of electron energy spread and beam current for the primary electron beam passing through the collision chamber were chosen to provide identical conditions for carrying out all the measurements. The energy scale was calibrated with the accuracy of ± 0.05 eV. The measured ionization cross-section normalized to the results

26 CFR 1.118-1 - Contributions to the capital of a corporation.

Science.gov (United States)

2010-04-01

... consideration for goods or services rendered, or to subsidies paid for the purpose of inducing the taxpayer to....118-1 Section 1.118-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Items Specifically Excluded from Gross Income § 1.118-1...

Sudden cardiac death in children (1-18 years)

DEFF Research Database (Denmark)

Winkel, Bo Gregers; Risgaard, Bjarke; Sadjadieh, Golnaz

2014-01-01

AIMS: Hitherto, sudden cardiac death in children (SCDc)-defined as sudden cardiac death (SCD) in the 1-18 years old-has been incompletely described in the general population. Knowledge on incidence rates, causes of death and symptoms prior to death is sparse and has been affected by reporting...... and referral bias. METHODS AND RESULTS: In a nationwide setting all deaths in children aged 1-18 years in Denmark in 2000-06 were included. To chart causes of death and incidence rates, death certificates and autopsy reports were collected and read. By additional use of the extensive healthcare registries...... in Denmark, we were also able to investigate prior disease and symptoms. During the 7-year study period there was an average of 1.11 million persons aged 1-18 years. There were a total of 1504 deaths (214 deaths per year) from 7.78 million person-years. A total of 114 (7.5%) were sudden and unexpected...

Leucocytes DNA damage in mice exposed to JS-118 by the comet assay.

Science.gov (United States)

Zhang, Tao; Hu, Jiye; Zhang, Yuchao; Zhao, Qianfei; Ning, Jun

2011-09-01

JS-118 is an extensively used insecticide in China. The present study investigated the genotoxic effect of JS-118 on whole blood at 24, 48, 72 and 96 h by using alkaline comet assay. Male Kunming mice were given 6.25, 12.5, 25, 50 and 100 mg/kg BW of JS-118 intraperitoneally. A statistically significant increase in all comet parameters indicating DNA damage was observed at 24 h post-treatment (p JS-118 and the period of treatment. The present study provided further information of the potential risk of the genetic damage caused by JS-118.

Reprint of “Extracellular production of tellurium nanoparticles by the photosynthetic bacterium Rhodobacter capsulatus”

Energy Technology Data Exchange (ETDEWEB)

Borghese, Roberto, E-mail: roberto.borghese@unibo.it [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy); Brucale, Marco [Institute for the Study of Nanostructured Materials (CNR-ISMN), Rome (Italy); Fortunato, Gianuario [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy); Lanzi, Massimiliano [Dept. of Industrial Chemistry “Toso Montanari”, University of Bologna (Italy); Mezzi, Alessio [Institute for the Study of Nanostructured Materials (CNR-ISMN), Rome (Italy); Valle, Francesco; Cavallini, Massimiliano [Institute for the Study of Nanostructured Materials (CNR-ISMN), Bologna (Italy); Zannoni, Davide [Dept. of Pharmacy and Biotechnology, University of Bologna (Italy)

2017-02-15

Highlights: • Tellurite is reduced by R. capsulatus as cytosolic tellurium nanoprecipitates TeNPs. • Lawsone allows R. capsulatus to produce extracellular TeNPs. • Extracellular TeNPs production depends on the carbon source used for cells growth. • Both lawsone concentration and the incubation time determine the TeNPs size. • Extracellular TeNPs are coated with extracellular polymeric substances (EPS). - Abstract: The toxic oxyanion tellurite (TeO{sub 3}{sup 2−}) is acquired by cells of Rhodobacter capsulatus grown anaerobically in the light, via acetate permease ActP2 and then reduced to Te{sup 0} in the cytoplasm as needle-like black precipitates. Interestingly, photosynthetic cultures of R. capsulatus can also generate Te{sup 0} nanoprecipitates (TeNPs) outside the cells upon addition of the redox mediator lawsone (2-hydroxy-1,4-naphtoquinone). TeNPs generation kinetics were monitored to define the optimal conditions to produce TeNPs as a function of various carbon sources and lawsone concentration. We report that growing cultures over a 10 days period with daily additions of 1 mM tellurite led to the accumulation in the growth medium of TeNPs with dimensions from 200 up to 600–700 nm in length as determined by atomic force microscopy (AFM). This result suggests that nucleation of TeNPs takes place over the entire cell growth period although the addition of new tellurium Te{sup 0} to pre-formed TeNPs is the main strategy used by R. capsulatus to generate TeNPs outside the cells. Finally, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR) analysis of TeNPs indicate they are coated with an organic material which keeps the particles in solution in aqueous solvents.

Total β-decay energies and masses of tin, antimony and tellurium isotopes in the vicinity of 50132Sn82

International Nuclear Information System (INIS)

Lund, E.; Aleklett, K.; Rudstam, G.

1977-01-01

Experimental β-decay energies for short-lived isotopes of tin, antimony and tellurium are presented. Mass-separated sources were produced at the on-line isotope separator OSIRIS. By applying β-γ coincidence methods, total β-decay energies have been determined for the following nuclides: 127-131 Sn, 128 130 131 134 Sb and 134 135 Te. The atomic mass excess has been derived for these nuclei, and comparisons are made with mass formula predictions. (Auth.)

In vitro and in vivo activity of an organic tellurium compound on Leishmania (Leishmania chagasi.

Directory of Open Access Journals (Sweden)

Isabella Aparecida Salerno Pimentel

Full Text Available Tellurium compounds have shown several biological properties and recently the leishmanicidal effect of one organotellurane was demonstrated. These findings led us to test the effect of the organotellurium compound RF07 on Leishmania (Leishmania chagasi, the agent of visceral leishmaniasis in Latin America. In vitro assays were performed in L. (L. chagasi-infected bone marrow derived macrophages treated with different concentrations of RF07. In in vivo experiments Golden hamsters were infected with L. (L. chagasi and injected intraperitoneally with RF07 whereas control animals received either Glucantime or PBS. The effect of RF07 on cathepsin B activity of L. (L. chagasi amastigotes was assayed spectrofluorometrically using fluorogenic substrates. The main findings were: 1 RF07 showed significant leishmanicidal activity against intracellular parasites at submicromolar concentrations (IC50 of 529.7±26.5 nM, and the drug displayed 10-fold less toxicity to macrophages (CC50 of 5,426±272.8 nM; 2 kinetics assays showed an increasing leishmanicidal action of RF07 at longer periods of treatment; 3 one month after intraperitoneal injection of RF07 L. (L. chagasi-infected hamsters showed a reduction of 99.6% of parasite burden when compared to controls that received PBS; 4 RF07 inhibited the cathepsin B activity of L. (L. chagasi amastigotes. The present results demonstrated that the tellurium compound RF07 is able to destroy L. (L. chagasi in vitro and in vivo at concentrations that are non toxic to the host. We believe these findings support further study of the potential of RF07 as a possible alternative for the chemotherapy of visceral leishmaniasis.

Ab-initio study of pure sup 7 sup 7 Se and sup 1 sup 2 sup 5 Te systems and of the sup 7 sup 7 Se nuclear quadrupole interaction in tellurium

CERN Document Server

Oh, Y K; Cho, H S

1999-01-01

Using the Hartree-Fock cluster procedure, we have studied the electric-field gradient tensors at the nuclear sites of sup 7 sup 7 Se and sup 1 sup 2 sup 5 Te in pure sup 1 sup 2 sup 5 Te systems and in tellurium crystalline system's with a sup 7 sup 7 Se impurity. From the results for the pure systems, sup 7 sup 7 Se in selenium and sup 1 sup 2 sup 5 Te in tellurium, using the observed quadrupole moments: Q( sup 7 sup 7 Se) 0.75 +- 0.07 barns and Q( sup 1 sup 2 sup 5 Te) = 0.35 +- 0.04 barns. Comparison is made with earlier values obtained by different methods. Using our calculated values of Q and the results of a study of the field-gradient tensors for sup 7 sup 7 Se in tellurium, the theoretical values of the quadrupole coupling constants are found to agree, within about 7 percent, with experiment. The calculated asymmetry parameters are also found to be in reasonable agreement with the experiment values, although the agreement not as close as in the case of the quadrupole -coupling constants. Directions fo...

37 CFR 1.18 - Patent post allowance (including issue) fees.

Science.gov (United States)

2010-07-01

... entity $1,190.00 (d) Publication fee $300.00. (e) For filing an application for patent term adjustment... (including issue) fees. 1.18 Section 1.18 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES General Provisions Fees...

Melt-gas phase equilibria and state diagrams of the selenium-tellurium system

Science.gov (United States)

Volodin, V. N.; Trebukhov, S. A.; Burabaeva, N. M.; Nitsenko, A. V.

2017-05-01

The partial pressures of saturated vapor of the components in the Se-Te system are determined and presented in the form of temperature-concentration dependences from which the boundaries of the melt-gas phase transition are calculated at atmospheric pressure and vacuums of 2000 and 100 Pa. The existence of azeotropic mixtures is revealed. It is found that the points of inseparably boiling melts correspond to 7.5 at % of Se and 995°C at 101325 Pa, 10.9 at % at 673°C and 19.5 at % at 522°C in vacuums of 2000 and 100 Pa, respectively. A complete state diagram is constructed, including the fields of gas-liquid equilibria at atmospheric and low pressures, the boundaries of which allow us to assess the behavior of selenium and tellurium upon distillation fractionation.

Simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples using hydride generation ICPMS

International Nuclear Information System (INIS)

Jankowski, L.M.; Breidenbach, R.; Bakker, I.J.I.; Epema, O.J.

2009-01-01

Full text: A quantitative method for simultaneous analysis of arsenic, antimony, selenium and tellurium in environmental samples is being developed using hydride generation ICPMS. These elements must be first transformed into hydride-forming oxidation states. This is particularly challenging for selenium and antimony because selenium is susceptible to reduction to the non-hydride-forming elemental state and antimony requires strong reducing conditions. The effectiveness of three reducing agents (KI, thiourea, cysteine) is studied. A comparison is made between addition of reducing agent to the sample and addition of KI to the NaBH 4 solution. Best results were obtained with the latter approach. (author)

Luminescent Tellurium-Doped Cadmium Sulfide Electrodes as Probes of Semiconductor Excited-State Deactivation Processes in Photoelectrochemical Cells.

Science.gov (United States)

1980-08-12

photocurrent and emission intensity. Whereas CdS:Te electrochemistry consisted of oxidation of an electrolyte 2+ reductant, ZnO underwent photoanodic...employed n- and 1 3 2,3 3 3,4p-type GaPl’ n-type ZnO , n-type CdS , and n- and p-type GaAs. We have focussed our attention recently on n-type, tellurium...should point out that our treatment of Or and 0x is not without precedent. Both GaP- and ZnO -based PECs have been examined in this regard.l12 The

The anti-inflammatory effects of the tellurium redox modulating compound, AS101, are associated with regulation of NFκB signaling pathway and nitric oxide induction in macrophages

Directory of Open Access Journals (Sweden)

Sredni Benjamin

2010-01-01

Full Text Available Abstract Background LPS-activated macrophages produce mediators which are involved in inflammation and tissue injury, and especially those associated with endotoxic shock. The non toxic tellurium compound ammonium tri-chloro(dioxoethylene-O,O'-tellurate, AS101, has been recently shown to exert profound anti-inflammatory properties in animal models, associated with its Te(IV redox chemistry. This study explores the anti-inflammatory properties of AS101 with respect to modulation of inflammatory cytokines production and regulation of iNOS transcription and expression in activated macrophages via targeting the NFkB complex. Results AS101 decreased production of IL-6 and in parallel down-regulated LPS-induced iNOS expression and NO secretion by macrophages. AS101 reduced IkB phosphorylation and degradation, and reduced NFkB nuclear translocalization, albeit these effects were exerted at different kinetics. Chromatin immunoprecipitation assays showed that AS101 treatment attenuated p50-subunit ability to bind DNA at the NFkB consensus site in the iNOS promotor following LPS induction. Conclusions Besides AS101, the investigation of therapeutic activities of other tellurium(IV compounds is scarce in the literature, although tellurium is the fourth most abundant trace element in the human body. Since IKK and NFkB may be regulated by thiol modifications, we may thus envisage, inview of our integrated results, that Te(IV compounds, may have important roles in thiol redox biological activity in the human body and represent a new class of anti-inflammatory compounds.

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Lindemann, T.; Prange, A.; Neidhart, B. [GKSS Research Centre, Geesthacht (Germany). Inst. of Physical and Chemical Analysis; Dannecker, W. [Hamburg Univ. (Germany). Inst. fuer Anorganische und Angewandte Chemie

2000-10-01

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 C whereas at -20 C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%. (orig.)

118-C-4 Horizontal Rod Cave Characterization Report

International Nuclear Information System (INIS)

Encke, B.D.; Thoren, R.A.

1998-03-01

This report addresses the characterization data collected from 118-C- 4 Horizontal Rod Cave in December 1996 and August 1997. The characterization activities evaluated the radiological status and identified hazardous materials locations. The scope of this report is limited to the 118-C-4 Facility Structure. Information in this report can be used to identify the waste streams, provide specific chemical and radiological data to aid in planning decontamination and decommissioning (D ampersand D) activities, and allow proper disposal of the demolition debris, as required by the Comprehensive Environmental Response, Compensation, and Liability Act of 1980

Effect of Lactobacillus salivarius bacteriocin Abp118 on the mouse and pig intestinal microbiota.

Directory of Open Access Journals (Sweden)

Eliette Riboulet-Bisson

Full Text Available Lactobacilli are gram-positive bacteria that are a subdominant element in the human gastrointestinal microbiota, and which are commonly used in the food industry. Some lactobacilli are considered probiotic, and have been associated with health benefits. However, there is very little culture-independent information on how consumed probiotic microorganisms might affect the entire intestinal microbiota. We therefore studied the impact of the administration of Lactobacillus salivarius UCC118, a microorganism well characterized for its probiotic properties, on the composition of the intestinal microbiota in two model animals. UCC118 has anti-infective activity due to production of the bacteriocin Abp118, a broad-spectrum class IIb bacteriocin, which we hypothesized could impact the microbiota. Mice and pigs were administered wild-type (WT L. salivarius UCC118 cells, or a mutant lacking bacteriocin production. The microbiota composition was determined by pyrosequencing of 16S rRNA gene amplicons from faeces. The data show that L. salivarius UCC118 administration had no significant effect on proportions of major phyla comprising the mouse microbiota, whether the strain was producing bacteriocin or not. However, L. salivarius UCC118 WT administration led to a significant decrease in Spirochaetes levels, the third major phylum in the untreated pig microbiota. In both pigs and mice, L. salivarius UCC118 administration had an effect on Firmicutes genus members. This effect was not observed when the mutant strain was administered, and was thus associated with bacteriocin production. Surprisingly, in both models, L. salivarius UCC118 administration and production of Abp118 had an effect on gram-negative microorganisms, even though Abp118 is normally not active in vitro against this group of microorganisms. Thus L. salivarius UCC118 administration has a significant but subtle impact on mouse and pig microbiota, by a mechanism that seems at least partially

Calculations of energy levels and electromagnetic properties for tellurium pair isotopes, by unified method

International Nuclear Information System (INIS)

Teixeira, R.R.P.

1988-01-01

Calculations with the Unified Model (vibrator coupled to two particles), of the energy levels and the eletromagnetic properties have been performed and compared with the twelve pair isotopes from tellurium with A between 112 and 134. The results were analysed using as particles interaction: pairing and SDI (Surface Delta Interaction). The SDI and 3 fonons collective states were used in the fittings, and a syntematic comparison between the theoretical and experimental results was made. The dependence of the results with the model parameters was determined, through large variation sof them. Calculations using 4 fonons have been made, and the importance of the introduced variations in the results was discussed. Calculations have been made in the VAX Computer of the Pelletron at IFUSP. (author) [pt

Development of tellurium oxide and lead-bismuth oxide glasses for mid-wave infra-red transmission optics

Science.gov (United States)

Zhou, Beiming; Rapp, Charles F.; Driver, John K.; Myers, Michael J.; Myers, John D.; Goldstein, Jonathan; Utano, Rich; Gupta, Shantanu

2013-03-01

Heavy metal oxide glasses exhibiting high transmission in the Mid-Wave Infra-Red (MWIR) spectrum are often difficult to manufacture in large sizes with optimized physical and optical properties. In this work, we researched and developed improved tellurium-zinc-barium and lead-bismuth-gallium heavy metal oxide glasses for use in the manufacture of fiber optics, optical components and laser gain materials. Two glass families were investigated, one based upon tellurium and another based on lead-bismuth. Glass compositions were optimized for stability and high transmission in the MWIR. Targeted glass specifications included low hydroxyl concentration, extended MWIR transmission window, and high resistance against devitrification upon heating. Work included the processing of high purity raw materials, melting under controlled dry Redox balanced atmosphere, finning, casting and annealing. Batch melts as large as 4 kilograms were sprue cast into aluminum and stainless steel molds or temperature controlled bronze tube with mechanical bait. Small (100g) test melts were typically processed in-situ in a 5%Au°/95%Pt° crucible. Our group manufactured and evaluated over 100 different experimental heavy metal glass compositions during a two year period. A wide range of glass melting, fining, casting techniques and experimental protocols were employed. MWIR glass applications include remote sensing, directional infrared counter measures, detection of explosives and chemical warfare agents, laser detection tracking and ranging, range gated imaging and spectroscopy. Enhanced long range mid-infrared sensor performance is optimized when operating in the atmospheric windows from ~ 2.0 to 2.4μm, ~ 3.5 to 4.3μm and ~ 4.5 to 5.0μm.

40 CFR 93.118 - Criteria and procedures: Motor vehicle emissions budget.

Science.gov (United States)

2010-07-01

... emissions budget. 93.118 Section 93.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... and procedures: Motor vehicle emissions budget. (a) The transportation plan, TIP, and project not from a conforming transportation plan and TIP must be consistent with the motor vehicle emissions budget...

Reaction of 1-bromo-3-chloropropane with tellurium and dimethyl telluride in the system of hydrazine hydrate-alkali

International Nuclear Information System (INIS)

Russavskaya, N.V.; Levanova, E.P.; Sukhomazova, Eh.N.; Grabel'nykh, V.A.; Elaev, A.V.; Klyba, L.V.; Zhanchipova, E.R.; Albanov, A.I.; Korotaeva, I.M.; Toryashinova, D.S.D.; Korchevin, N.A.

2006-01-01

A synthesis of oligomeric substance of thiocol type, the poly(trimethyleneditelluride), from 1-bromo-3-chloropropane and elemental tellurium is performed using a hydrazine hydrate-alkali system. Reductive splitting of the tellurocol followed by alkylation with methyl iodide give rise to preparation of bis(methyltelluro)propane, which was synthesized also from dimethyl telluride and 1,3-dihalopropanes using the N 2 H 4 ·H 2 O/KOH system. The reaction products were characterized by elementary analysis, NMR, and IR spectra. Mass spectra of the synthesized low molecular weight organotellurium compounds are considered [ru

An Extended IEEE 118-Bus Test System With High Renewable Penetration

Energy Technology Data Exchange (ETDEWEB)

Pena, Ivonne; Martinez-Anido, Carlo Brancucci; Hodge, Bri-Mathias

2018-01-01

This article describes a new publicly available version of the IEEE 118-bus test system, named NREL-118. The database is based on the transmission representation (buses and lines) of the IEEE 118-bus test system, with a reconfigured generation representation using three regions of the US Western Interconnection from the latest Western Electricity Coordination Council (WECC) 2024 Common Case [1]. Time-synchronous hourly load, wind, and solar time series are provided for over one year (8784 hours). The public database presented and described in this manuscript will allow researchers to model a test power system using detailed transmission, generation, load, wind, and solar data. This database includes key additional features that add to the current IEEE 118-bus test model, such as: the inclusion of 10 generation technologies with different heat rate functions, minimum stable levels and ramping rates, GHG emissions rates, regulation and contingency reserves, and hourly time series data for one full year for load, wind and solar generation.

Potential for improved extraction of tellurium as a byproduct of current copper mining processes

Science.gov (United States)

Hayes, S. M.; Spaleta, K. J.; Skidmore, A. E.

2016-12-01

Tellurium (Te) is classified as a critical element due to its increasing use in high technology applications, low average crustal abundance (3 μg kg-1), and primary source as a byproduct of copper extraction. Although Te can be readily recovered from copper processing, previous studies have estimated a 4 percent extraction efficiency, and few studies have addressed Te behavior during the entire copper extraction process. The goals of the present study are to perform a mass balance examining Te behavior during copper extraction and to connect these observations with mineralogy of Te-bearing phases which are essential first steps in devising ways to optimize Te recovery. Our preliminary mass balance results indicate that less than 3 percent of Te present in copper ore is recovered, with particularly high losses during initial concentration of copper ore minerals by flotation. Tellurium is present in the ore in telluride minerals (e.g., Bi-Te-S phases, altaite, and Ag-S-Se-Te phases identified using electron microprobe) with limited substitution into sulfide minerals (possibly 10 mg kg-1 Te in bulk pyrite and chalcopyrite). This work has also identified Te accumulation in solid-phase intermediate extraction products that could be further processed to recover Te, including smelter dusts (158 mg kg-1) and pressed anode slimes (2.7 percent by mass). In both the smelter dusts and anode slimes, X-ray absorption spectroscopy indicates that about two thirds of the Te is present as reduced tellurides. In anode slimes, electron microscopy shows that the remaining Te is present in an oxidized form in a complex Te-bearing oxidate phase also containing Pb, Cu, Ag, As, Sb, and S. These results clearly indicate that more efficient, increased recovery of Te may be possible, likely at minimal expense from operating copper processing operations, thereby providing more Te for manufacturing of products such as inexpensive high-efficiency solar panels.

Agglomeration during wet milling of LAST (lead-antimony-silver-tellurium) powders

International Nuclear Information System (INIS)

Hall, B.D.; Case, E.D.; Ren, F.; Johnson, J.R.; Timm, E.J.

2009-01-01

LAST (lead-antimony-silver-tellurium) compounds comprise a family of semiconducting materials with good thermoelectric properties. However, the as-cast form of LAST exhibits large grain size and hence low mechanical strength. Powder processing can produce a fine powder particle size that enhances fracture strength, however the powders tend to agglomerate if the individual powder diameters are less than a few microns across. Dry milling or wet milling (hexane additions of 0 cm 3 and 10 cm 3 ) produced hard agglomerates roughly 40 μm in diameter while wet milling with hexane additions of 25 cm 3 , 30 cm 3 or 50 cm 3 resulted in small, porous agglomerates roughly 20 μm in diameter. Thus, by adjusting the amount of milling liquid used while milling LAST powders, one can shift from hard to soft agglomerates, where the literature shows that soft agglomerates are less harmful to the final, sintered product. Also, in agreement with the results from the literature on other materials, wet milling of LAST powders produced smaller particle sizes but required longer times to reach the grindability limit

7 CFR 1221.118 - Refund escrow accounts.

Science.gov (United States)

2010-01-01

... Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING... INFORMATION ORDER Sorghum Promotion, Research, and Information Order Sorghum Promotion, Research, and Information Board § 1221.118 Refund escrow accounts. (a) The Board shall establish an interest bearing escrow...

41 CFR 102-118.60 - To what extent must my agency use electronic commerce?

Science.gov (United States)

2010-07-01

... agency use electronic commerce? 102-118.60 Section 102-118.60 Public Contracts and Property Management... Services § 102-118.60 To what extent must my agency use electronic commerce? Your agency must use electronic commerce in all areas of your transportation program. This includes the use of electronic systems...

Cleanup Verification Package for the 118-F-5 PNL Sawdust Pit

International Nuclear Information System (INIS)

Habel, L.D.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance with cleanup criteria for the 118-F-5 Burial Ground, the PNL (Pacific Northwest Laboratory) Sawdust Pit. The 118-F-5 Burial Ground was an unlined trench that received radioactive sawdust from the floors of animal pens in the 100-F Experimental Animal Farm

Reduced HRAS G12V-Driven Tumorigenesis of Cell Lines Expressing KRAS C118S.

Directory of Open Access Journals (Sweden)

Lu Huang

Full Text Available In many different human cancers, one of the HRAS, NRAS, or KRAS genes in the RAS family of small GTPases acquires an oncogenic mutation that renders the encoded protein constitutively GTP-bound and thereby active, which is well established to promote tumorigenesis. In addition to oncogenic mutations, accumulating evidence suggests that the wild-type isoforms may also be activated and contribute to oncogenic RAS-driven tumorigenesis. In this regard, redox-dependent reactions with cysteine 118 (C118 have been found to promote activation of wild-type HRAS and NRAS. We sought to determine if this residue is also important for the activation of wild-type KRAS and promotion of tumorigenesis. Thus, we mutated C118 to serine (C118S in wild-type KRAS to block redox-dependent reactions at this site. We now report that this mutation reduced the level of GTP-bound KRAS and impaired RAS signaling stimulated by the growth factor EGF. With regards to tumorigenesis, we also report that oncogenic HRAS-transformed human cells in which endogenous KRAS was knocked down and replaced with KRASC118S exhibited reduced xenograft tumor growth, as did oncogenic HRAS-transformed KrasC118S/C118S murine cells in which the C118S mutation was knocked into the endogenous Kras gene. Taken together, these data suggest a role for redox-dependent activation of wild-type KRAS through C118 in oncogenic HRAS-driven tumorigenesis.

Laser resonance ionization scheme development for tellurium and germanium at the dual Ti:Sa–Dye ISOLDE RILIS

CERN Document Server

Day Goodacre, T.; Fedosseev, V.N.; Forster, L.; Marsh, B.A.; Rossel, R.E.; Rothe, S.; Veinhard, M.

2016-01-01

The resonance ionization laser ion source (RILIS) is the principal ion source of the ISOLDE radioactive beam facility based at CERN. Using the method of in-source laser resonance ionization spectroscopy, a transition to a new autoionizing state of tellurium was discovered and applied as part of a three-step, three-resonance, photo-ionization scheme. In a second study, a three-step, two-resonance, photo-ionization scheme for germanium was developed and the ionization efficiency was measured at ISOLDE. This work increases the range of ISOLDE RILIS ionized beams to 31 elements. Details of the spectroscopy studies are described and the new ionization schemes are summarized.

Laser resonance ionization scheme development for tellurium and germanium at the dual Ti:Sa–Dye ISOLDE RILIS

Energy Technology Data Exchange (ETDEWEB)

Day Goodacre, T., E-mail: thomas.day.goodacre@cern.ch [CERN, CH-1211 Geneva 23 (Switzerland); School of Physics and Astronomy, The University of Manchester, Manchester M13 9PL (United Kingdom); Fedorov, D. [Petersburg Nuclear Physics Institute, 188350 Gatchina (Russian Federation); Fedosseev, V.N.; Forster, L.; Marsh, B.A. [CERN, CH-1211 Geneva 23 (Switzerland); Rossel, R.E. [CERN, CH-1211 Geneva 23 (Switzerland); Institut für Physik, Johannes Gutenberg Universität, D-55099 Mainz (Germany); Faculty of Design, Computer Science and Media, Hochschule RheinMain, Wiesbaden (Germany); Rothe, S.; Veinhard, M. [CERN, CH-1211 Geneva 23 (Switzerland)

2016-09-11

The resonance ionization laser ion source (RILIS) is the principal ion source of the ISOLDE radioactive beam facility based at CERN. Using the method of in-source laser resonance ionization spectroscopy, a transition to a new autoionizing state of tellurium was discovered and applied as part of a three-step, three-resonance, photo-ionization scheme. In a second study, a three-step, two-resonance, photo-ionization scheme for germanium was developed and the ionization efficiency was measured at ISOLDE. This work increases the range of ISOLDE RILIS ionized beams to 31 elements. Details of the spectroscopy studies are described and the new ionization schemes are summarized.

40 CFR 92.118 - Analyzer checks and calibrations.

Science.gov (United States)

2010-07-01

... (CONTINUED) CONTROL OF AIR POLLUTION FROM LOCOMOTIVES AND LOCOMOTIVE ENGINES Test Procedures § 92.118... sampling system at the sample probe or valve V2 at atmospheric pressure. Simultaneously, start the time...

50 CFR 18.118 - What are the mitigation, monitoring, and reporting requirements?

Science.gov (United States)

2010-10-01

... reporting requirements? 18.118 Section 18.118 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE... avoid significant additive and synergistic effects from multiple oil and gas exploration activities on... conducted i.e., a plan of operation; (B) A food and waste management plan; (C) Personnel training materials...

29 CFR 570.118 - Sixteen-year minimum.

Science.gov (United States)

2010-07-01

... Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR REGULATIONS CHILD LABOR REGULATIONS, ORDERS AND STATEMENTS OF INTERPRETATION General Statements of Interpretation of the Child Labor Provisions of the Fair Labor Standards Act of 1938, as Amended Oppressive Child Labor § 570.118 Sixteen-year...

Tank 241-TX-118 tank characterization plan

International Nuclear Information System (INIS)

Carpenter, B.C.

1994-01-01

This document is a plan which serves as the contractual agreement between the Characterization Program, Sampling Operations, Oak Ridge National Laboratory, and PNL tank vapor program. The scope of this plan is to provide guidance for the sampling and analysis of vapor samples from tank 241-TX-118

23 CFR 635.118 - Payroll and weekly statements.

Science.gov (United States)

2010-04-01

... CONSTRUCTION AND MAINTENANCE Contract Procedures § 635.118 Payroll and weekly statements. For all projects... contract provisions for the project, are to be retained by the STD for the time period pursuant to 49 CFR...

Effect of aging and temperature on alternating current conductivity of tellurium thin films

Energy Technology Data Exchange (ETDEWEB)

Tsiulyanu, D. [Technical University, Department of Physics, bul. Dacia 41, MD-2060, Chisinau (Moldova, Republic of)], E-mail: tsiu@cni.md; Marian, T.; Tiuleanu, A. [Technical University, Department of Physics, bul. Dacia 41, MD-2060, Chisinau (Moldova, Republic of); Liess, H.-D.; Eisele, I. [University of the Bundeswehr Munich, Faculty of Electrical Engineering and Information Technology, Institute of Physics, D-85577 Neubiberg (Germany)

2009-02-27

The impedance spectra of tellurium films with interdigital platinum electrodes were investigated in air at temperatures between 10 and 50 deg. C . Cole-Cole analysis made it possible to assess time constants, resistance, and capacitance of the film at characteristic frequencies and the dependence of these parameters on aging and temperature. Aging under normal conditions over 12 months led to a relative increase of only {approx} 5% in film impedance at the characteristic frequency. However, aging noticeably influences the electrical resistance of the film at high (> 500 kHz) frequencies, and capacitance diminished after 12 months by more than 50% throughout the spectrum. Scanning electron microscopy confirmed that the effect of aging is due to structural changes in the film. Temperature does not influence the capacitance of the film but uncommonly influences its resistance, which reaches a maximum at around 20 deg. C . This is ascribed to desorption of oxygen previously adsorbed from the environment.

Effect of aging and temperature on alternating current conductivity of tellurium thin films

International Nuclear Information System (INIS)

Tsiulyanu, D.; Marian, T.; Tiuleanu, A.; Liess, H.-D.; Eisele, I.

2009-01-01

The impedance spectra of tellurium films with interdigital platinum electrodes were investigated in air at temperatures between 10 and 50 deg. C . Cole-Cole analysis made it possible to assess time constants, resistance, and capacitance of the film at characteristic frequencies and the dependence of these parameters on aging and temperature. Aging under normal conditions over 12 months led to a relative increase of only ∼ 5% in film impedance at the characteristic frequency. However, aging noticeably influences the electrical resistance of the film at high (> 500 kHz) frequencies, and capacitance diminished after 12 months by more than 50% throughout the spectrum. Scanning electron microscopy confirmed that the effect of aging is due to structural changes in the film. Temperature does not influence the capacitance of the film but uncommonly influences its resistance, which reaches a maximum at around 20 deg. C . This is ascribed to desorption of oxygen previously adsorbed from the environment

Study on concentration nonlinearity of interacting acoustic flows in cadmium sulfide and tellurium

International Nuclear Information System (INIS)

Ilisavskij, Yu.V.; Kulakova, L.A.; Yakhkind, Eh.Z.

1976-01-01

The ratio of an one-mode (self-action of an external monochromatic sound wave) and a many-mode (interaction of an external wave with crystal thermal phonons) concentration nonlinearity has been experimentally investigated on sound amplification in cadmium sulphide and tellurium. It has been shown that in a strong piezoelectric the main part in the nonlinear limitation of the sound amplification in a drift field is played by the wave interaction, i.e., the transfer of the sound wave energy into the crystal sound modes starts before the nonlinear self-action of a wave. In Te characterized by a large value of the electromechanical coupling constant value at the sound frequency of about 250 MHz the threshold of many-mode nonlinearity is achieved in fields much below the critical one, and corresponds to the sound intensity as low as 10 -7 W/cm 2 , as compared with 10 -2 W/cm 2 -the threshold of the one-mode nonlinearity

Electrochemical and antimicrobial activity of tellurium oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Gupta, Pramod K. [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Sharma, Prem Prakash; Sharma, Anshu [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India); Khan, Zishan H., E-mail: zishan_hk@yahoo.co.in [Department of Applied Sciences and Humanities, Jamia Millia Islamia, New Delhi 110067 (India); Solanki, Pratima R., E-mail: pratimarsolanki@gmail.com [Special Centre for Nanosciences, Jawaharlal Nehru University, New Delhi 110067 (India)

2016-09-15

Highlights: • TeO{sub 2} NPs synthesized without using any catalyst by chemical vapour deposition method. • The growth temperature was 410 °C with continuous flow of O{sub 2.} • TeO{sub 2} NPs have anti-bacterial activity against E. coli, K. pneumoniae and S. aureus while enhances the growth of S. pyogenes. • TeO{sub 2} shows maximum redox current at pH 7 for phosphate buffer solution. - Abstract: Thin film of tellurium oxide (TeO{sub 2}) has been synthesized by chemical vapour deposition method onto indium tin oxide (ITO) coated glass substrate without using any catalyst. XRD pattern of TeO{sub 2} thin film suggests that the structure of TeO{sub 2} changes from amorphous to crystalline (paratellurite) on dispersing into deionized water. Zeta potential measurement reveals a positive surface potential of 28.8 mV. TEM images shows spherical shaped TeO{sub 2} nanoparticles having average particle size of 65 nm. Electrochemical studies of TeO{sub 2}/ITO electrode exhibit improved electron transfer owing to its inherent electron transfer property at pH 7.0 of phosphate buffer. Antimicrobial activity of TeO{sub 2} has been studied for gram-positive (Staphylococcus aureus and Streptococcus pyogenes) and gram negative (Escherichia coli and Klebsiella pneumoniae) bacterial and fungal strains (Aspergillus nizer and Candida albicans). These studies suggest that the TeO{sub 2} NPs inhibit the growth of E. coli, K. pneumoniae and S. aureus bacteria, whereas the same particles enhance the growth of S. pyogenes bacteria.

Antiparasitic activity of 1,3-dioxolanes containing tellurium in Trichomonas vaginalis.

Science.gov (United States)

Sena-Lopes, Ângela; das Neves, Raquel Nascimento; Bezerra, Francisco Silvestre Brilhante; de Oliveira Silva, Mara Thais; Nobre, Patrick C; Perin, Gelson; Alves, Diego; Savegnago, Lucielli; Begnini, Karine Rech; Seixas, Fabiana Kommling; Collares, Tiago; Borsuk, Sibele

2017-05-01

The increased prevalence of metronidazole-resistant infections has resulted in a search for alternative drugs for the treatment of trichomoniasis. In the present study, we report the preparation and in vitro activity of three 1,3-dioxolanes that contain tellurium (PTeDOX 01, PTeDOX 02, and PTeDOX 03) against Trichomonas vaginalis. Six concentrations of these compounds were analyzed for in vitro activity against ATCC 30236 isolate of T. vaginalis. PTeDOX 01 reported a cytotoxic effect against 100% of T. vaginalis trophozoites at a final concentration of 90μM with an IC 50 of 60μM. The kinetic growth curve of trophozoites indicated that PTeDOX 01 reduced the growth by 22% at a concentration of 90μM after an exposure of 12h, and induced complete parasite death at 24h. It induced cytotoxicity of 44% at 90μM concentration but and had no effect in lower concentrations in a culture of CHO-K1 cells. These results confirmed that PTeDOX 01 is an important drug for the treatment of T. vaginalis, and should be evaluated in other infectious agents as well. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

STS-118 Astronaut Tracy Caldwell During Training

Science.gov (United States)

2006-01-01

Tracy E. Caldwell, STS-118 astronaut and mission specialist, participates in a training session on the usage of a special device, used to lower oneself from a troubled shuttle, in the Space Vehicle Mockup Facility at the Johnson Space Center. Caldwell is wearing a training version of her shuttle launch and entry suit.

Leaching of cadmium and tellurium from cadmium telluride (CdTe) thin-film solar panels under simulated landfill conditions

Science.gov (United States)

Ramos-Ruiz, Adriana; Wilkening, Jean V.; Field, James A.; Sierra-Alvarez, Reyes

2017-01-01

A crushed non-encapsulated CdTe thin-film solar cell was subjected to two standardized batch leaching tests (i.e., Toxicity Characteristic Leaching Procedure (TCLP) and California Waste Extraction Test (WET)) and to a continuous-flow column test to assess cadmium (Cd) and tellurium (Te) dissolution under conditions simulating the acidic- and the methanogenic phases of municipal solid waste landfills. Low levels of Cd and Te were solubilized in both batch leaching tests (leaching behavior of CdTe in the columns is related to different aqueous pH and redox conditions promoted by the microbial communities in the columns, and is in agreement with thermodynamic predictions. PMID:28472709

41 CFR 102-118.65 - Can my agency receive electronic billing for payment of transportation services?

Science.gov (United States)

2010-07-01

... electronic billing for payment of transportation services? 102-118.65 Section 102-118.65 Public Contracts and... Transportation Services § 102-118.65 Can my agency receive electronic billing for payment of transportation... to use electronic billing for the procurement and billing of transportation services. ...

Life as a sober citizen: Aldo Leopold's Wildlife Ecology 118

Science.gov (United States)

Theiss, Nancy Stearns

This historic case study addressed the issue of the lack of citizen action toward environmentally responsible behavior. Although there have been studies regarding components of environmental responsible behavior [ERB], there has been little focus on historic models of exemplary figures of ERB. This study examined one of the first conservation courses in the United States, Wildlife Ecology 118, taught by Aldo Leopold (1887--1948) for 13 years at the University of Wisconsin. Today, Aldo Leopold is recognized as an exemplary conservationist whose land ethic is cited as providing the ecological approach needed for understanding the complex issues of modern society. The researcher conjectured that examination of one of the first environmental education courses could support and strengthen environmental education practices by providing a heuristic perspective. The researcher used two different strategies for analysis of the case. For Research Question One---"What were Leopold's teaching strategies in Wildlife Ecology 118?"---the researcher used methods of comparative historical analysis. The researcher examined the learning outcomes that Leopold used in Wildlife Ecology 118 and compared them against a rubric of the Four Strands for Environmental Education (North American Association for Environmental Education [NAAEE], 1999). The Four Strands for Environmental Education are the current teaching strategies used by educators. The results indicated that Wildlife Ecology 118 scored high in Knowledge of Processes and Systems and Environmental Problem Solving strands. Leopold relied on historic case examples and animal biographies to build stories that engaged students. Field trips gave students practical experience for environmental knowledge with special emphasis on phenology. For Research Question Two---"What was the context of the lessons in Wildlife Ecology 118?"---the researcher used environmental history methods for analysis. Context provided the knowledge and

Tank 241-TX-118 vapor sampling and analysis tank characterization report

International Nuclear Information System (INIS)

Huckaby, J.L.

1995-01-01

Tank 241-TX-118 headspace gas and vapor samples were collected and analyzed to help determine the potential risks to tank farm workers due to fugitive emissions from the tank. The drivers and objectives of waste tank headspace sampling and analysis are discussed in open-quotes Program Plan for the Resolution of Tank Vapor Issues.close quotes Tank 241-TX-118 was vapor sampled in accordance with open-quotes Data Quality Objectives for Generic In-Tank Health and Safety Issue Resolution.close quotes

Optical properties of tellurium-doped InxGa1-xAsySb1-y epitaxial layers studied by photoluminescence spectroscopy

International Nuclear Information System (INIS)

Diaz-Reyes, J; Cardona-Bedoya, J A; Gomez-Herrera, M L; Herrera-Perez, J L; Riech, I; Mendoza-Alvarez, J G

2003-01-01

Controlled doping of quaternary alloys of In x Ga 1-x As y Sb 1-y with tellurium is fundamental to obtain the n-type layers needed for the development of optoelectronic devices based on p-n heterojunctions. InGaAsSb epitaxial layers were grown by liquid phase epitaxy and Te doping was obtained by incorporating small Sb 3 Te 2 pellets in the growth melt. The tellurium doping levels were in the range 10 16 -10 17 cm -3 . We have used low-temperature photoluminescence (PL) spectroscopy to study the influence of the Te donor levels on the radiative transitions shown in the PL spectra. The PL measurements were done by exciting the samples with the 448 nm line of an Ar ion laser with varying excitation powers in the range from 10 to 200 mW. For the low-doped sample the PL spectrum showed a narrow exciton-related peak centred at around 610 meV with a full width at half maximum (FWHM) of about 7 meV which is evidence of the good crystalline quality of the layers. For higher Te doping, the PL spectra show the presence of band-to-band and donor-to-acceptor transitions which overlap as the Te concentration increases. The peak of the PL band shifts to higher energies as Te doping increases due to a band-filling effect as the Fermi level enters into the conduction band. From the peak energy of the PL spectra, and using a model that includes the band-filling and band-shrinkage effects due to the carriers, we have estimated the effective carrier concentration due to doping with Te in the epilayers

41 CFR 102-118.80 - Who is responsible for keeping my agency's electronic commerce transportation billing records?

Science.gov (United States)

2010-07-01

... keeping my agency's electronic commerce transportation billing records? 102-118.80 Section 102-118.80... Transportation and Transportation Services § 102-118.80 Who is responsible for keeping my agency's electronic commerce transportation billing records? Your agency's internal financial regulations will identify...

From Selenium- to Tellurium-Based Glass Optical Fibers for Infrared Spectroscopies

Directory of Open Access Journals (Sweden)

Jacques Lucas

2013-05-01

Full Text Available Chalcogenide glasses are based on sulfur, selenium and tellurium elements, and have been studied for several decades regarding different applications. Among them, selenide glasses exhibit excellent infrared transmission in the 1 to 15 µm region. Due to their good thermo-mechanical properties, these glasses could be easily shaped into optical devices such as lenses and optical fibers. During the past decade of research, selenide glass fibers have been proved to be suitable for infrared sensing in an original spectroscopic method named Fiber Evanescent Wave Spectroscopy (FEWS. FEWS has provided very nice and promising results, for example for medical diagnosis. Then, some sophisticated fibers, also based on selenide glasses, were developed: rare-earth doped fibers and microstructured fibers. In parallel, the study of telluride glasses, which can have transmission up to 28 µm due to its atom heaviness, has been intensified thanks to the DARWIN mission led by the European Space Agency (ESA. The development of telluride glass fiber enables a successful observation of CO2 absorption band located around 15 µm. In this paper we review recent results obtained in the Glass and Ceramics Laboratory at Rennes on the development of selenide to telluride glass optical fibers, and their use for spectroscopy from the mid to the far infrared ranges.

Structural Modeling of Djenkolic Acid with Sulfur Replaced by Selenium and Tellurium

Directory of Open Access Journals (Sweden)

Petr Melnikov

2014-04-01

Full Text Available The comparative structural modeling of djenkolic acid and its derivatives containing selenium and tellurium in chalcogen sites (Ch = Se, Te has provided detailed information about the bond lengths and bond angles, filling the gap in what we know about the structural characteristics of these aminoacids. The investigation using the molecular mechanics technique with good approximation confirmed the available information on X-ray refinements for the related compounds methionine and selenomethionine, as well as for an estimate made earlier for telluromethionine. It was shown that the Ch-C(3 and Ch-C(4 bond lengths grow in parallel with the increasing anionic radii. Although the distances C-C, C-O, and C-N are very similar, the geometry of conformers is quite different owing to the possibility of rotation about four carbon atoms, hence the remarkable variability observed in dihedral angles. It was shown that the compounds contain a rigid block with two Ch atoms connected through a methylene group. The standard program Gaussian 03 with graphical interface Gaussview 4.1.2 has proved to be satisfactory tool for the structural description of less-common bioactive compositions when direct X-ray results are absent.

Direct determination of tellurium and its redox speciation at the low nanogram level in natural waters by catalytic cathodic stripping voltammetry.

Science.gov (United States)

Biver, Marc; Quentel, François; Filella, Montserrat

2015-11-01

Tellurium is one of the elements recently identified as technologically critical and is becoming a new emergent contaminant. No reliable method exists for its determination in environmental samples such as natural waters. This gap is filled by the method described here; it allows the rapid detection of trace concentrations of Te(IV) and Te(VI) in surface waters by differential pulse cathodic stripping voltammetry. It is based on the proton reduction catalysed by the absorption of Te(IV) on the mercury electrode. Under our conditions (0.1 mol L(-1) HCl) a detection limit of about 5 ng L(-1) for a deposition time of 300 s is achieved. Organic matter does not represent a problem at low concentrations; higher concentrations are eliminated by adsorptive purification. Tellurium occurs primarily as Te(IV) and Te(VI) in natural waters. Thus, determining total Te requires the reduction of Te(VI) that it is not electroactive. A number of reduction procedures have been carefully evaluated and a method based on the addition of TiCl3 to the acidified samples has been proven to reduce Te(VI) at the trace level to Te(IV) reliably and quantitatively. Therefore, the procedure described allows the direct determination of total Te and its redox speciation. It is flexible, reliable and cost effective compared to any possible alternative method based on the common preconcentration-ICPMS approach. It is readily implementable as a routine method and can be deployed in the field with relative ease. Copyright © 2015 Elsevier B.V. All rights reserved.

Tellurium Stable Isotopes as a Paleoredox Proxy

Science.gov (United States)

Wasserman, N.; Johnson, T. M.

2017-12-01

Despite arguments for variably-oxygenated shallow waters and anoxic deep marine waters, which delayed animal development until the Neoproterozoic Oxidation Event, the magnitude of atmospheric oxygen during the Proterozoic is still uncertain [1]. The evidence for low pO2 (<0.1-1% PAL) is based on geochemical and isotopic proxies, which track the mobilization of Fe and Mn on the continents. For example, large chromium isotope shifts occur at the Neoproterozoic Oxidation Event due to the initiation of Cr redox cycling, but this proxy is insensitive to fluctuations in the lower-pO2 conditions at other times during the Proterozoic. Tellurium, a metalloid with a lower threshold to oxidation, may be sensitive to pO2 shifts in a lower range. In the reduced forms, Te(-II) and Te(0), the element is insoluble and immobile. However, in the more oxidized phases, Te(IV) and Te(VI), Te can form soluble oxyanions (though it tends to adsorb to Fe-oxyhydroxides and clays) [2]. Te stable isotopes have been shown to fractionate during abiotic or biologic reduction of Te(VI) or Te(IV) to elemental Te(0) [3, 4]. Utilizing hydride generation MC-ICP-MS, we are able to obtain high precision (2σ 0.04‰) measurements of δ128Te/125Te for natural samples containing < 10 ng of Te. A suite of Phanerozoic and Proterozoic ironstones show significant variation in δ128Te/125Te (<0.5‰), suggesting that the Te redox cycle was active during the Proterozoic. Future directions will include Te isotope measurements of Precambrian paleosols to determine natural isotope variation before the Great Oxidation Event and experiments to determine fractionation during adsorption to Fe-oxyhydroxides. [1] Planavsky et al. (2014) Science 346 (6209), pp. 635-638 [2] Qin et al. (2017) Environmental Science and Technology 51 (11), pp 6027-6035 [3] Baesman et al. (2007) Applied Environmental Microbiology 73 (7), pp 2135-2143 [4] Smithers and Krause (1968) Canadian Journal of Chemistry 46(4): pp 583-591

41 CFR 102-118.260 - Must my agency send all quotations, tenders, or contracts with a TSP to GSA?

Science.gov (United States)

2010-07-01

... quotations, tenders, or contracts with a TSP to GSA? 102-118.260 Section 102-118.260 Public Contracts and... REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Use of Government Billing Documents Quotations, Tenders Or Contracts § 102-118.260 Must my agency send all quotations, tenders, or contracts with a TSP to...

E2-EPF UCP Possesses E3 Ubiquitin Ligase Activity via Its Cysteine 118 Residue.

Science.gov (United States)

Lim, Jung Hwa; Shin, Hee Won; Chung, Kyung-Sook; Kim, Nam-Soon; Kim, Ju Hee; Jung, Hong-Ryul; Im, Dong-Soo; Jung, Cho-Rok

Here, we show that E2-EPF ubiquitin carrier protein (UCP) elongated E3-independent polyubiquitin chains on the lysine residues of von Hippel-Lindau protein (pVHL) and its own lysine residues both in vitro and in vivo. The initiation of the ubiquitin reaction depended on not only Lys11 linkage but also the Lys6, Lys48 and Lys63 residues of ubiquitin, which were involved in polyubiquitin chain formation on UCP itself. UCP self-association occurred through the UBC domain, which also contributed to the interaction with pVHL. The polyubiquitin chains appeared on the N-terminus of UCP in vivo, which indicated that the N-terminus of UCP contains target lysines for polyubiquitination. The Lys76 residue of UCP was the most critical site for auto-ubiquitination, whereas the polyubiquitin chain formation on pVHL occurred on all three of its lysines (Lys159, Lys171 and Lys196). A UCP mutant in which Cys118 was changed to alanine (UCPC118A) did not form a polyubiquitin chain but did strongly accumulate mono- and di-ubiquitin via auto-ubiquitination. Polyubiquitin chain formation required the coordination of Cys95 and Cys118 between two interacting molecules. The mechanism of the polyubiquitin chain reaction of UCP may involve the transfer of ubiquitin from Cys95 to Cys118 by trans-thiolation, with polyubiquitin chains forming at Cys118 by reversible thioester bonding. The polyubiquitin chains are then moved to the lysine residues of the substrate by irreversible isopeptide bonding. During the elongation of the ubiquitin chain, an active Cys118 residue is required in both parts of UCP, namely, the catalytic enzyme and the substrate. In conclusion, UCP possesses not only E2 ubiquitin conjugating enzyme activity but also E3 ubiquitin ligase activity, and Cys118 is critical for polyubiquitin chain formation.

E2-EPF UCP Possesses E3 Ubiquitin Ligase Activity via Its Cysteine 118 Residue.

Directory of Open Access Journals (Sweden)

Jung Hwa Lim

Full Text Available Here, we show that E2-EPF ubiquitin carrier protein (UCP elongated E3-independent polyubiquitin chains on the lysine residues of von Hippel-Lindau protein (pVHL and its own lysine residues both in vitro and in vivo. The initiation of the ubiquitin reaction depended on not only Lys11 linkage but also the Lys6, Lys48 and Lys63 residues of ubiquitin, which were involved in polyubiquitin chain formation on UCP itself. UCP self-association occurred through the UBC domain, which also contributed to the interaction with pVHL. The polyubiquitin chains appeared on the N-terminus of UCP in vivo, which indicated that the N-terminus of UCP contains target lysines for polyubiquitination. The Lys76 residue of UCP was the most critical site for auto-ubiquitination, whereas the polyubiquitin chain formation on pVHL occurred on all three of its lysines (Lys159, Lys171 and Lys196. A UCP mutant in which Cys118 was changed to alanine (UCPC118A did not form a polyubiquitin chain but did strongly accumulate mono- and di-ubiquitin via auto-ubiquitination. Polyubiquitin chain formation required the coordination of Cys95 and Cys118 between two interacting molecules. The mechanism of the polyubiquitin chain reaction of UCP may involve the transfer of ubiquitin from Cys95 to Cys118 by trans-thiolation, with polyubiquitin chains forming at Cys118 by reversible thioester bonding. The polyubiquitin chains are then moved to the lysine residues of the substrate by irreversible isopeptide bonding. During the elongation of the ubiquitin chain, an active Cys118 residue is required in both parts of UCP, namely, the catalytic enzyme and the substrate. In conclusion, UCP possesses not only E2 ubiquitin conjugating enzyme activity but also E3 ubiquitin ligase activity, and Cys118 is critical for polyubiquitin chain formation.

Determination of tellurium in gallium by alternating current stripping voltammetry with a mercury/graphite electrode

International Nuclear Information System (INIS)

Berengard, I.B.; Kaplan, B. Ya.

1986-01-01

The analytical signal in ac stripping coltammetry (ACSV) with mercury indicator electrodes depends on the weight of the electrolytically collected analyte at the electrode surface, the depth of the collection layer being equal to the effective diffusion-layer thickness. Replacement of the static mercury drop electrode (SMDE) by the mercury/graphite electrode (MGE) is of practical interest in that the analyte detection limit can be lowered by decreasing the colume of the telluriumcontaining polarographed solution; in addition, plant laboratories find it difficult to control the SDME uniformity. The work in this article was done on a PU-1 universal polarograph in a square-wave vol tage component mode using the three-electrode cell shown. The rotating mercury/graphite electrode is found by the authors to be superior to the static mercury drop electrode in that it can lower the detection limit for tellurium in gallium to 5.10 /SUP -7percent/ , due to the smaller volume of the polarographed solution

47 CFR 15.118 - Cable ready consumer electronics equipment.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cable ready consumer electronics equipment. 15... Unintentional Radiators § 15.118 Cable ready consumer electronics equipment. (a) All consumer electronics TV... provisions of this section. Consumer electronics TV receiving equipment that includes features intended for...

Dibromidochlorido{2-[(dimethylaminomethyl]phenyl-κ2N,C1}tellurium(IV

Directory of Open Access Journals (Sweden)

Prakul Rakesh

2012-01-01

Full Text Available The title compound, C9H13Br2ClNTe, was synthesized by reacting [2-(dimethylaminomethylphenyl]tellurium(II chloride with Br2. As a consequence, the Cl and Br atoms are not well ordered but distributed over the three possible positions such that the overall stiochiometry is two Br atoms and one Cl atom. The scrambling of the Br and Cl atoms indicates a small energy barrier for the exchange process between the apical and equatorial positions. Overall, the Te atom geometry is slightly distorted square pyramidal (τ = 0.052 for the major component. However, there is a weak secondary interaction between the Te atoms and the disordered Br/Cl atoms of a nearby molecule. The Te—Br and Te—Cl distances in both disorder components fall into two groups; a longer distance for the Br/Cl involved in this secondary interaction [2.6945 (17 Å for Br and 2.601 (9Å for Cl] and shorter bond distances to the remaining halogen atoms, indicating that this interaction has slightly weakened the Te—X bond, as is the case in the previously reported tribromido structure [Singh et al. (1990. J. Chem. Soc. Dalton Trans. pp. 907–913]. Otherwise, the metrical parameters in the two structures are not significantly different. An intermolecular C—H...Br interaction occurs.

41 CFR 102-118.130 - Must my agency use a GBL for express, courier, or small package shipments?

Science.gov (United States)

2010-07-01

... package express delivery, the terms and conditions of that contract are binding. ... for express, courier, or small package shipments? 102-118.130 Section 102-118.130 Public Contracts and... Transportation Services § 102-118.130 Must my agency use a GBL for express, courier, or small package shipments...

Hydrolysis and photolysis of diacylhydrazines-type insect growth regulator JS-118 in aqueous solutions under abiotic conditions.

Science.gov (United States)

Hu, J-Y; Liu, C; Zhang, Y-C; Zheng, Z-X

2009-05-01

JS-118 is a diacylhydrazines-type insect growth regulator which is now used extensively in China. The hydrolysis and photolysis of the pesticide JS-118 in aqueous solutions have been assessed under natural and controlled conditions in this project. Hydrolysis experimental results show that JS-118 is quite stable in aqueous solutions in dark, with no significant variations be observed in degradation under various conditions. Abiotic hydrolysis is relatively unimportant compared to photolysis. The rate of photodecomposition of JS-118 in aqueous solutions follows first-order kinetics both in UV radiation and natural sunlight. The degradation rates are faster under UV light than sunlight, with the half-lives (t (1/2) = ln2/k) of 6.00-10.85 min and 6.63-10.16 day, respectively. Under UV light, two major photoproducts are detected, and tentatively identified according to HPLC-MS spectral information as N-t-butyl-N-(3,5-dimethylbenzoyl) and 3,7-dimethyl-benzoatedihydrofuran. The corresponding photolysis pathways of JS-118 are also proposed. The results obtained indicate that direct photoreaction is an important dissipation pathway of JS-118 in natural water systems.

Size Controlled Synthesis of Tellurium Nanorices by Galvanic Displacement Reaction of Aluminum

International Nuclear Information System (INIS)

Wu, Tingjun; Myung, Lawrence Youngjae; Zhang, Miluo; Lee, Kyu-Hwan; Lee, Yeheun Laura; Lim, Hyo-Ryong; Kim, Bum Sung; Choa, Yong-Ho; Myung, Nosang V.

2015-01-01

ABSTRACT: Tellurium nanostructures were synthesized by galvanic displacement reaction (GDR) of aluminum in an alkaline solution containing TeO 3 2− ions. Due to negative redox potential of Al/AlO 2 − (i.e., −2.50 V vs. sat. Ag/AgCl), TeO 3 2− (+IV) can be reduced to Te 2 2− (-I) and Te 2− (-II), which resulted in the deposition of Te (0) nanostructures in the solution via chemical reaction between Te 2 2− or Te 2− and TeO 3 2− . The deposition mechanism led to the formation of unique “rice-like” nanostructures in the solution instead of branched structures on the substrate. The sharp tips of the “rice-like” nanostructures may be attributed to the high density of surface charges at the tips. The morphology, diameter and aspect ratio of Te “rice-like” nanostructures were altered by the TeO 3 2− concentration, solution pH, reaction time and the reaction temperature. Electrochemical analytical methods, including open circuit potential (OCP) and linear polarizations (LPs), were used to investigate the reaction mechanisms. The enhancement of piezoelectric constant (d 11 ) of nanorices at small diameter was probably due to a flexoelectric effect

25 CFR 900.118 - Do these “construction contract” regulations apply to construction management services?

Science.gov (United States)

2010-04-01

... construction management services? 900.118 Section 900.118 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE...” regulations apply to construction management services? No. Construction management services may be contracted separately under section 108 of the Act. Construction management services consultants and/or Indian tribe or...

Closure Report for Corrective Action Unit 118: Area 27 Super Kukla Facility, Nevada Test Site, Nevada, Revision 0

International Nuclear Information System (INIS)

Mark Burmeister

2007-01-01

This CR provides documentation and justification for the closure of CAU 118 without further corrective action. This justification is based on process knowledge and the results of the investigative and closure activities conducted in accordance with the CAU 118 SAFER Plan: Streamlined Approach for Environmental Restoration (SAFER) Plan for CAU 118: Area 27 Super Kukla Facility, Nevada Test Site, Nevada (NNSA/NSO, 2006). The SAFER Plan provides information relating to site history as well as the scope and planning of the investigation. This CR also provides the analytical and radiological survey data to confirm that the remediation goals were met as specified in the CAU 118 SAFER Plan (NNSA/NSO, 2006). The Nevada Division of Environmental Protection (NDEP) approved the CAU 118 SAFER Plan (Murphy, 2006), which recommends closure in place with use restrictions (URs)

33 CFR 118.100 - Retroreflective panels on bridge piers.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Retroreflective panels on bridge... SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.100 Retroreflective panels on bridge piers. The... 12 inches square. (c) To mark bridge piers or channel sides on bridges not required to have bridge...

Cleanup Verification Package for the 118-B-6, 108-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Proctor, M.L.

2006-01-01

This cleanup verification package documents completion of remedial action for the 118-B-6, 108-B Solid Waste Burial Ground. The 118-B-6 site consisted of 2 concrete pipes buried vertically in the ground and capped by a concrete pad with steel lids. The site was used for the disposal of wastes from the 'metal line' of the P-10 Tritium Separation Project.

The Present, Mid-Term, and Long-Term Supply Curves for Tellurium; and Updates in the Results from NREL's CdTe PV Module Manufacturing Cost Model (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Woodhouse, M.; Goodrich, A.; Redlinger, M.; Lokanc, M.; Eggert, R.

2013-09-01

For those PV technologies that rely upon Te, In, and Ga, first-order observations and calculations hint that there may be resource constraints that could inhibit their successful deployment at a SunShot level. These are only first-order approximations, however, and the possibility for an expansion in global Te, In, and Ga supplies needs to be considered in the event that there are upward revisions in their demand and prices.In this study, we examine the current, mid-term, and long-term prospects of Tellurium (Te) for use in PV. We find that the current global supply base of Te would support <10 GW of annual traditional CdTe PV manufacturing production. But as for the possibility that the supply base for Te might be expanded, after compiling several preliminary cumulative availability curves we find that there may be significant upside potential in the supply base for this element - principally vis a vis increasing demand and higher prices. Primarily by reducing the Tellurium intensity in manufacturing and by increasing the recovery efficiency of Te in Cu refining processes, we calculate that it may prove affordable to PV manufacturers to expand the supply base for Te such that 100 GW, or greater, of annual CdTe PV production is possible in the 2030 - 2050 timeframe.

24 CFR 1000.118 - What recourse does a recipient have if HUD disapproves a proposal to provide assistance to non...

Science.gov (United States)

2010-04-01

... housing activity? 1000.118 Section 1000.118 Housing and Urban Development Regulations Relating to Housing... § 1000.118 What recourse does a recipient have if HUD disapproves a proposal to provide assistance to non...

21 CFR 118.4 - Salmonella Enteritidis (SE) prevention measures.

Science.gov (United States)

2010-04-01

... specified in § 118.6, within 2 weeks of the start of egg laying. (3) Cleaning and disinfection. If the... house to remove dust, feathers, and old feed; and (iii) Following cleaning, disinfection of the positive... harborage for pests. (d) Cleaning and disinfection. You must clean and disinfect the poultry house according...

41 CFR 102-118.420 - Can the Administrator of General Services waive the postpayment auditing provisions of this subpart?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Can the Administrator of General Services waive the postpayment auditing provisions of this subpart? 102-118.420 Section 102-118... Transportation Audits § 102-118.420 Can the Administrator of General Services waive the postpayment auditing...

33 CFR 118.85 - Lights on vertical lift bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on vertical lift bridges... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.85 Lights on vertical lift bridges. (a) Lift span lights. The vertical lift span of every vertical lift bridge shall be lighted so that the center of the...

Molecular single-bond covalent radii for elements 1-118.

Science.gov (United States)

Pyykkö, Pekka; Atsumi, Michiko

2009-01-01

A self-consistent system of additive covalent radii, R(AB)=r(A) + r(B), is set up for the entire periodic table, Groups 1-18, Z=1-118. The primary bond lengths, R, are taken from experimental or theoretical data corresponding to chosen group valencies. All r(E) values are obtained from the same fit. Both E-E, E-H, and E-CH(3) data are incorporated for most elements, E. Many E-E' data inside the same group are included. For the late main groups, the system is close to that of Pauling. For other elements it is close to the methyl-based one of Suresh and Koga [J. Phys. Chem. A 2001, 105, 5940] and its predecessors. For the diatomic alkalis MM' and halides XX', separate fits give a very high accuracy. These primary data are then absorbed with the rest. The most notable exclusion are the transition-metal halides and chalcogenides which are regarded as partial multiple bonds. Other anomalies include H(2) and F(2). The standard deviation for the 410 included data points is 2.8 pm.

Hepatocellular carcinoma: a retrospective analysis of 118 cases

International Nuclear Information System (INIS)

Aman-ur-Rehman; Murad, S.

2002-01-01

Objective: This study aimed at documenting the spectrum of clinico pathological variations in hepatocellular carcinoma (HCC). Design: It was a retrospective study. Place and duration of Study: This study was conducted at the Institute of Nuclear Medicine and Oncology (INMOL) Hospital, Lahore from March 1997 to December 2000. Patients and Methods: The profiles of 118 patients with a biopsy proven hepatocellular carcinoma were analyzed in this period. The data collected was age, sex, clinical presentation and laboratory investigations including liver function tests, alpha fetoprotein and hepatitis profile. Results: Weight loss, jaundice and right upper quadrant abdominal pain were the main presenting symptoms. Out of 118 patients, alpha fetoprotein values were raised in 63(53.38%) patients 106 (89.83%) patients were found to have or have had HBV infections, and 92 (77.96%) patients were anti-HCV positive. Eighty-three (70.33%) patients were cirrhotic. History of alcohol abuse was bound in three patients. Conclusion: The common association of HCC with cirrhosis and hepatitis B and C suggests that vaccination against HBV on nationwide basis can decrease prevalence of this malignancy. There is a need to generate public awareness regarding the transmission of these viruses. Early diagnosis and intervention is also important to the successful management of HCC. (author)

38 CFR 1.18 - Guidelines for establishing presumptions of service connection for former prisoners of war.

Science.gov (United States)

2010-07-01

... establishing presumptions of service connection for former prisoners of war. 1.18 Section 1.18 Pensions... Guidelines for establishing presumptions of service connection for former prisoners of war. (a) Purpose. The Secretary of Veterans Affairs will establish presumptions of service connection for former prisoners of war...

0+ analogue state in 118Sb from 117Sn(p,nγ) reaction

International Nuclear Information System (INIS)

Pal, J.; Dey, C.C.; Bose, S.; Sinha, B.K.; Chatterjee, M.B.; Mahapatra, D.P.

1996-01-01

The analogue of the 0 + ground state in 118 Sn has been observed in the compound nucleus 118 Sb through 117 Sn(p,nγ) 117 Sb reaction. The neutron decays of this analogue resonance have been studied from the deexciting γ-rays of the residual nucleus 117 Sb. From off resonance excitation functions, spin assignments have been made to states in 117 Sb, on the basis of Hauser-Feshbach formalism. The resonance parameters of the isobaric analogue resonance have been determined, including the total, proton and neutron decay widths. (orig.)

Equilibrium evaporation behavior of polonium and its homologue tellurium in liquid lead-bismuth eutectic

International Nuclear Information System (INIS)

Ohno, Shuji; Miyahara, Shinya; Kurata, Yuji; Katsura, Ryoei; Yoshida, Shigeru

2006-01-01

Experimental study using the transpiration method investigates equilibrium evaporation behavior of radionuclide polonium ( 210 Po) generated and accumulated in liquid lead-bismuth eutectic (LBE) cooled nuclear systems. The experiment consists of two series of tests: preliminary evaporation tests for homologue element tellurium (Te) in LBE, and evaporation tests for 210 Po-accumulated LBE in which test specimens are prepared by neutron irradiation. The evaporation tests of Te in LBE provide the suggestion that Te exists in a chemical form of PbTe as well as the information for confirming the validity of technique and conditions of Po test. From the evaporation tests of 210 Po in LBE, we obtain fundamental data and empirical equations such as 210 Po vapor concentration in the gas phase, 210 Po partial vapor pressure, thermodynamic activity coefficients, and gas-liquid equilibrium partition coefficient of 210 Po in LBE in the temperature range from 450 to 750degC. Additionally, radioactivity concentration of 210 Po and 210m Bi vapor in a cover gas region of a typical LBE-cooled nuclear system is specifically estimated based on the obtained experimental results, and the importance of 210 Po evaporation behavior is quantitatively demonstrated. (author)

Iron-tellurium-selenium mixed oxide catalysts for the selective oxidation of propylene to acrolein

International Nuclear Information System (INIS)

Patel, B.M.; Price, G.L.

1990-01-01

This paper reports on iron-tellurium-selenium mixed oxide catalysts prepared by coprecipitation from aqueous solution investigated for the propylene to acrolein reaction in the temperature range 543-773 K. Infrared spectroscopy, electron dispersive X-ray analysis, X-ray diffraction, and isotopic tracer techniques have also been employed to characterize this catalytic system. Properties of the Fe-Te-Se mixed oxide catalysts have been compared with Fe-Te mixed oxides in an effort to deduce the functionality of Se. The selenium in the Fe-Te-Se-O catalyst has been found to be the hydrocarbon activating site. The activation energies for the acrolein and carbon dioxide formation are 71 and 54 kJ/mol, respectively. Reactions carried out with 18 O 2 have shown lattice oxygen to be primarily responsible for the formation of both acrolein and carbon dioxide. The initial and rate-determining step for acrolein formation is hydrogen abstraction as determined by an isotope effect associated with the C 3 D 6 reaction. No isotope effect is observed for carbon dioxide formation from C 3 D 6 suggesting that CO 2 is formed by parallel, not consecutive, oxidation of propylene

Enhanced Flexural Strength of Tellurium Nanowires/epoxy Composites with the Reinforcement Effect of Nanowires

Science.gov (United States)

Balguri, Praveen Kumar; Harris Samuel, D. G.; Aditya, D. B.; Vijaya Bhaskar, S.; Thumu, Udayabhaskararao

2018-02-01

Investigating the mechanical properties of polymer nanocomposite materials has been greatly increased in the last decade. In particular, flexural strength plays a major role in resisting bending and shear loads of a composite material. Here, one dimensional (1D) tellurium nanowires (TeNWs) reinforced epoxy composites have been prepared and the flexural properties of resulted TeNWs/epoxy nanocomposites are studied. The diameter and length of the TeNWs used to make TeNWs/epoxy nanocomposites are 21±2.5 nm and 697±87 nm, respectively. Plain and TeNWs/epoxy nanocomposites are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). Furthermore, significant enhancement in the flexural strength of TeNWs/epoxy nanocomposite is observed in comparison to plain epoxy composite, i.e. flexural strength is increased by 65% with the addition of very little amount of TeNWs content (0.05 wt.%) to epoxy polymer. Structural details of plain and TeNWs/epoxy at micrometer scale were examined by scanning electron microscopy (SEM). We believe that our results provide a new type of semiconductor nanowires based high strength epoxy polymer nanocomposites.

Comparative analysis of Nb and Ti addition in the Cu-11,8%wt.Al-0,5%wt.Be e Cu-11,8%wt.Al-3,0%wt.Ni shape memory alloy; Analise comparativa da adicao de NB e TI nas ligas Cu-11,8Al-0,5Be e Cu-11,8Al-3,0Ni passiveis do efeito memoria de forma

Energy Technology Data Exchange (ETDEWEB)

Silva Junior, M.Q. da; Oliveira, G.D. de, E-mail: manoel.quirino@ufersa.edu.br [Universidade Federal Rural do Semi-Arido (UFERSA), Mossoro, RN (Brazil)

2014-07-01

The system of the Cu-Al alloys shape memory alloy have been the subject of many studies due to a wide range of possible applications and relatively low cost, and the chemical composition of the main factors that determine the properties of these properties. This work analyzed the influence of Nb and Ti elements in Cu-11,8Al-0,5Be and Cu-11,8Al-3,0Ni alloy. The alloys are obtained by melting and passed through homogenizing heat treatment followed by water quenching at 30°C. The samples were characterized by Microscopy Optical, X-ray Diffraction and Microhardness testing. The alloys showed fine precipitates of second phase homogeneously distributed in the matrix that provides improvement in the properties of these alloys. (author)

Improved selectivity for Pb(II) by sulfur, selenium and tellurium analogues of 1,8-anthraquinone-18-crown-5: synthesis, spectroscopy, X-ray crystallography and computational studies.

Science.gov (United States)

Mariappan, Kadarkaraisamy; Alaparthi, Madhubabu; Hoffman, Mariah; Rama, Myriam Alcantar; Balasubramanian, Vinothini; John, Danielle M; Sykes, Andrew G

2015-07-14

We report here a series of heteroatom-substituted macrocycles containing an anthraquinone moiety as a fluorescent signaling unit and a cyclic polyheteroether chain as the receptor. Sulfur, selenium, and tellurium derivatives of 1,8-anthraquinone-18-crown-5 (1) were synthesized by reacting sodium sulfide (Na2S), sodium selenide (Na2Se) and sodium telluride (Na2Te) with 1,8-bis(2-bromoethylethyleneoxy)anthracene-9,10-dione in a 1 : 1 ratio. The optical properties of the new compounds are examined and the sulfur and selenium analogues produce an intense green emission enhancement upon association with Pb(II) in acetonitrile. Selectivity for Pb(II) is markedly improved as compared to the oxygen analogue 1 which was also competitive for Ca(II) ion. UV-Visible and luminescence titrations reveal that 2 and 3 form 1 : 1 complexes with Pb(II), confirmed by single-crystal X-ray studies where Pb(II) is complexed within the macrocycle through coordinate covalent bonds to neighboring carbonyl, ether and heteroether donor atoms. Cyclic voltammetry of 2-8 showed classical, irreversible oxidation potentials for sulfur, selenium and tellurium heteroethers in addition to two one-electron reductions for the anthraquinone carbonyl groups. DFT calculations were also conducted on 1, 2, 3, 6, 6 + Pb(II) and 6 + Mg(II) to determine the trend in energies of the HOMO and the LUMO levels along the series.

17 CFR 1.18 - Records for and relating to financial reporting and monthly computation by futures commission...

Science.gov (United States)

2010-04-01

... financial reporting and monthly computation by futures commission merchants and introducing brokers. 1.18... UNDER THE COMMODITY EXCHANGE ACT Minimum Financial and Related Reporting Requirements § 1.18 Records for and relating to financial reporting and monthly computation by futures commission merchants and...

Receptor binding proteins of Listeria monocytogenes bacteriophages A118 and P35 recognize serovar-specific teichoic acids

Energy Technology Data Exchange (ETDEWEB)

Bielmann, Regula; Habann, Matthias; Eugster, Marcel R. [Institute of Food, Nutrition and Health, ETH Zurich, Schmelzbergstrasse 7, 8092 Zurich (Switzerland); Lurz, Rudi [Max-Planck Institute for Molecular Genetics, 14195 Berlin (Germany); Calendar, Richard [Department of Molecular and Cell Biology, University of California, Berkeley, CA 94720-3202 (United States); Klumpp, Jochen, E-mail: jochen.klumpp@hest.ethz.ch [Institute of Food, Nutrition and Health, ETH Zurich, Schmelzbergstrasse 7, 8092 Zurich (Switzerland); Loessner, Martin J. [Institute of Food, Nutrition and Health, ETH Zurich, Schmelzbergstrasse 7, 8092 Zurich (Switzerland)

2015-03-15

Adsorption of a bacteriophage to the host requires recognition of a cell wall-associated receptor by a receptor binding protein (RBP). This recognition is specific, and high affinity binding is essential for efficient virus attachment. The molecular details of phage adsorption to the Gram-positive cell are poorly understood. We present the first description of receptor binding proteins and a tail tip structure for the siphovirus group infecting Listeria monocytogenes. The host-range determining factors in two phages, A118 and P35 specific for L. monocytogenes serovar 1/2 have been determined. Two proteins were identified as RBPs in phage A118. Rhamnose residues in wall teichoic acids represent the binding ligands for both proteins. In phage P35, protein gp16 could be identified as RBP and the role of both rhamnose and N-acetylglucosamine in phage adsorption was confirmed. Immunogold-labeling and transmission electron microscopy allowed the creation of a topological model of the A118 phage tail. - Highlights: • We present the first description of receptor binding proteins and a tail tip structure for the Siphovirus group infecting Listeria monocytogenes. • The host-range determining factors in two phages, A118 and P35 specific for L. monocytogenes serovar 1/2 have been determined. • Rhamnose residues in wall teichoic acids represent the binding ligands for both receptor binding proteins in phage A118. • Rhamnose and N-acetylglucosamine are required for adsorption of phage P35. • We preset a topological model of the A118 phage tail.

Raman and DSC studies of fragility in tellurium-zinc oxide glass formers

International Nuclear Information System (INIS)

Stavrou, Elissaios; Kripotou, Sotiria; Raptis, Constantine; Turrell, Sylvia; Syassen, Karl

2011-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out in four mixed (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses at high temperatures (Raman and DSC through the glass transition) and high pressures (Raman) with the aim of determining the fragility of these glass forming oxides. Four different criteria, corresponding to four parameters, were applied to assess the fragility of the glasses. From the DSC studies, we have obtained the fragility parameter m which corresponds to the slopes of Arrhenius (lnQ vs. 1/T g , were Q is the heating rate) plots, and the glass transition width ΔT g . Also, from the low-frequency Raman scattering, and in particular the boson peak intensity of the glasses at T g , we have estimated the fragility ratio r R (T g ) = I min /I max whose value serves as another (empirical) fragility criterion. Finally, from high pressure Raman measurements on the glasses, we have estimated the Grueneisen parameter γ T for each glass, which constitutes the fourth fragility parameter adopted in this work. Considering the four parameters ΔT g , m, r (T g ) and γ T and the generally accepted (empirical) fragility criteria, we conclude that the mixed tellurium-zinc oxides constitute strong-to-intermediate glass formers (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

41 CFR 102-118.35 - What definitions apply to this part?

Science.gov (United States)

2010-07-01

... PAYMENT AND AUDIT General Definitions § 102-118.35 What definitions apply to this part? The following... terms and conditions of a contract in electronic communication. Electronic commerce means electronic... 10721), or other equivalent contract, arrangement or exemption from regulation. Postpayment audit means...

41 CFR 102-118.350 - Does establishing a prepayment audit system or program change the responsibilities of the...

Science.gov (United States)

2010-07-01

... prepayment audit system or program change the responsibilities of the certifying officers? 102-118.350... System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT... Does establishing a prepayment audit system or program change the responsibilities of the certifying...

A simple fast microwave-assisted synthesis of thermoelectric bismuth telluride nanoparticles from homogeneous reaction-mixture

Energy Technology Data Exchange (ETDEWEB)

Pradhan, Susmita [Jadavpur University, Department of Instrumentation Science (India); Das, Rashmita [Jadavpur University, Department of Instrumentation and Electronics Engineering (India); Bhar, Radhaballabh [Jadavpur University, Department of Instrumentation Science (India); Bandyopadhyay, Rajib [Jadavpur University, Department of Instrumentation and Electronics Engineering (India); Pramanik, Panchanan, E-mail: pramanik1946@gmail.com [GLA University, Department of Chemistry and Nanoscience (India)

2017-02-15

A new simple chemical method for synthesis of nanocrystalline bismuth telluride (Bi{sub 2}Te{sub 3}) has been developed by microwave assisted reduction of homogeneous tartrate complexes of bismuth and tellurium metal ions with hydrazine. The reaction is performed at pH 10. The nano-crystallites have rhombohedral phase identified by XRD. The size distribution of nanoparticle is narrow and it ranges between 50 to 70 nm. FESEM shows that the fine powders are composed of small crystallites. The TEM micrographs show mostly deformed spherical particles and the lattice fringes are found to be 0.137 nm. Energy dispersive X-ray spectroscopy (EDX) analysis shows the atomic composition ratio between bismuth and tellurium is 2:3. Thermoelectric properties of the materials are studied after sintering by spark plasma sintering method (SPS). The grain size of the material after sintering is in the nanometer range. The material shows enhanced Seebeck coefficient and electrical conductivity value at 300 K. The figure of merit is found to be 1.18 at 300 K.

Pharmacology, pharmacokinetics and metabolism of the dopamine receptor agonist 5-hydroxy-6-methyl-2-di-n-propylaminotetralin (DK-118) in the cat

International Nuclear Information System (INIS)

Koons, J.C.

1985-01-01

The dopamine receptor agonist 5-hydroxy-6-methyl-2-di-n-propylaminotetralin (DK-118) lowers blood pressure, heart rat and inhibits tachycardia induced in cats by electrical stimulation of sympathetic nerves innervating the heart. DK-118, unlike most of its chemically related dopaminergic analogs, exhibits a slow onset of activity suggesting that one or more metabolites of the drug may be responsible for its pharmacologic effects. The purpose of the work described in this thesis was to gain information regarding the possible bioactivation of DK-118 in cats. In one series of experiments, cats were pretreated with inhibitors of drug metabolism, metyrapone or SKF 525-A, and alterations of the pharmacologic effects of DK-118 determined. A high-performance liquid chromatography assay-using electrochemical detection was developed to quantify urine and plasma concentrations of DK-118 in control, metyrapone pretreated and SKF 525-A pretreated cats. Urinary metabolites of [ 14 C]DK-118 were identified employing HPLC, GC/MS and FAB/MS. Pharmacologic activity and receptor binding of selected metabolites were determined. Data presented in this thesis are consistent with the hypothesis that metabolites contribute to some of the pharmacologic effects of DK-118

12 CFR 225.118 - Computer services for customers of subsidiary banks.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Computer services for customers of subsidiary...) Regulations Financial Holding Companies Interpretations § 225.118 Computer services for customers of... status if it should provide data processing services for customers of the subsidiary banks. (b) The Board...

7 CFR 28.118 - When no fee collected for new certificate or memorandum.

Science.gov (United States)

2010-01-01

... MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE COMMODITY... United States Cotton Standards Act Fees and Costs § 28.118 When no fee collected for new certificate or...

Antimicrobial activity against Porphyromonas gingivalis and mechanism of action of the cationic octadecapeptide AmyI-1-18 and its amino acid-substituted analogs.

Science.gov (United States)

Taniguchi, Masayuki; Ochiai, Akihito; Takahashi, Kiyoshi; Nakamichi, Shun-Ichi; Nomoto, Takafumi; Saitoh, Eiichi; Kato, Tetsuo; Tanaka, Takaaki

2016-12-01

The antimicrobial peptide AmyI-1-18 is a cationic α-helical octadecapeptide derived from α-amylase in rice (Oryza sativa L. japonica) that contains four cationic amino acid residues (two arginines and two lysines). To enhance the antibacterial activity of AmyI-1-18 against Porphyromonas gingivalis (a bacterium associated with periodontal disease), we synthesized 12 analogs bearing substitutions with alanine, leucine, and/or arginine that were designed based on helical wheel projections and investigated their antibacterial properties. The antibacterial properties of four analogs bearing substitution of a single arginine or lysine with alanine were almost similar to those of AmyI-1-18, suggesting that the antibacterial properties depend on the presence of three cationic amino acid residues. Of three single arginine-substituted analogs, AmyI-1-18(G12R) exhibited an antibacterial activity 2.8-fold higher [50% growth-inhibitory concentration (IC 50 ): 4.6 μM] than that of AmyI-1-18 (IC 50 : 13 μM). Likewise, the antibacterial properties of two single leucine-substituted analogs were significantly enhanced; in particular, AmyI-1-18(N3L) exhibited an antibacterial activity (IC 50 : 2.5 μM) 5.2-fold higher than that of AmyI-1-18. The hemolytic activity of AmyI-1-18(N3L) against mammalian red blood cells was low (2% at 50 μM). A membrane-depolarization assay using a membrane potential-sensitive fluorescent dye revealed that, similar to AmyI-1-18, the antibacterial activity of AmyI-1-18(N3L) was not dependent on its membrane-disrupting activity. Our results demonstrate that the antibacterial properties of AmyI-1-18 against P. gingivalis are significantly improved, without a significant increase in hemolytic activity, by replacing asparagine with leucine at position 3. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Cleanup Verification Package for the 118-F-6 Burial Ground

International Nuclear Information System (INIS)

Sulloway, H.M.

2008-01-01

This cleanup verification package documents completion of remedial action for the 118-F-6 Burial Ground located in the 100-FR-2 Operable Unit of the 100-F Area on the Hanford Site. The trenches received waste from the 100-F Experimental Animal Farm, including animal manure, animal carcasses, laboratory waste, plastic, cardboard, metal, and concrete debris as well as a railroad tank car

Cleanup Verification Package for the 118-F-2 Burial Ground

International Nuclear Information System (INIS)

Capron, J.M.; Anselm, K.A.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance with cleanup criteria for the 118-F-2 Burial Ground. This burial ground, formerly called Solid Waste Burial Ground No. 1, was the original solid waste disposal site for the 100-F Area. Eight trenches contained miscellaneous solid waste from the 105-F Reactor and one trench contained solid waste from the biology facilities

Test of irradiation of tellurium oxide for obtaining iodine-131 by dry distillation; Prueba de irradiacion de dioxido de telurio para obtener yodo-131 por destilacion seca

Energy Technology Data Exchange (ETDEWEB)

Alanis M, J. [ININ, Departamento de Materiales Radiactivos, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-15

With the purpose of optimizing to the maximum independently the work of the reactor of those mathematical calculations of irradiation that are already optimized, now it corresponds to carry out irradiation tests in the different positions with their respective neutron fluxes that it counts the reactor for samples irradiation. Then, it is necessary to carry out the irradiation of the tellurium dioxide through cycles, with the purpose of observing the activity that it goes accumulating in each cycle and this way to obtain an activity of the Iodine-131 obtained when finishing the last cycle. (Author)

Comparative analysis of Nb and Ti addition in the Cu-11,8%wt.Al-0,5%wt.Be e Cu-11,8%wt.Al-3,0%wt.Ni shape memory alloy

International Nuclear Information System (INIS)

Silva Junior, M.Q. da; Oliveira, G.D. de

2014-01-01

The system of the Cu-Al alloys shape memory alloy have been the subject of many studies due to a wide range of possible applications and relatively low cost, and the chemical composition of the main factors that determine the properties of these properties. This work analyzed the influence of Nb and Ti elements in Cu-11,8Al-0,5Be and Cu-11,8Al-3,0Ni alloy. The alloys are obtained by melting and passed through homogenizing heat treatment followed by water quenching at 30°C. The samples were characterized by Microscopy Optical, X-ray Diffraction and Microhardness testing. The alloys showed fine precipitates of second phase homogeneously distributed in the matrix that provides improvement in the properties of these alloys. (author)

[Postoperative complications and survival analysis of 1 118 cases of open splenectomy and azygoportal disconnection in the treatment of portal hypertension].

Science.gov (United States)

Qi, R Z; Zhao, X; Wang, S Z; Zhang, K; Chang, Z Y; Hu, X L; Wu, M L; Zhang, P R; Yu, L X; Xiao, C H; Shi, X J; Li, Z W

2018-06-01

Objective: To analyze the recent postoperative and long-term postoperative complications of open-splenectomy and disconnection in patients with portal hypertension. Methods: There were 1 118 cases with portal hypertension who underwent open splenectomy and azygoportal disconnection from April 2010 to September 2015 at Department of Surgery, People's Liberation Army 302 Hospital. Retrospective case investigation and telephone follow-up were conducted in October 2016. All patients had history of upper gastrointestinal bleeding before operation. Short-term complications after surgery were recorded including secondary laparotomy of postoperative abdominal hemostasis, severe infection, intake disorders, liver insufficiency, postoperative portal vein thrombosis and perioperative mortality. Long-term data including postoperative upper gastrointestinal rebleeding, postoperative survival rate and incidence of postoperative malignancy were recorded, too. GraphPad Prism 5 software for data survival analysis and charting. Results: Postoperative short-term complications in 1 118 patients included secondary laparotomy of postoperative abdominal hemostasis(1.8%, 21/1 118), severe infection(2.9%, 32/1 118), intake disorders(1.0%, 11/1 118), liver dysfunction (1.6%, 18/1 118), postoperative portal vein thrombosis(47.1%, 526/1 118)and perioperative mortality(0.5%, 5/1 118). After phone call following-up, 942 patients' long-term data were completed including 1, 3, 5 years postoperative upper gastrointestinal rebleeding rate(4.4%, 12.1%, 17.2%), 1, 3, 5-year postoperative survival rate(97.0%, 93.5%, 90.3%); the incidence of postoperative malignant tumors in 1, 3 and 5 years were 1.7%, 4.4% and 6.2%. Conclusions: Reasonable choosing of surgical indications and timing, proper performing the surgery process, effective conducting perioperative management of portal hypertension are directly related to the patient's short-term prognosis after portal hypertension. Surgical intervention can

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

International Nuclear Information System (INIS)

Wan Buyong; Hu Chenguo; Liu Hong; Xiong Yufeng; Li Feiyun; Xi Yi; He Xiaoshan

2009-01-01

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

Growth of PbTe nanorods controlled by polymerized tellurium anions and metal(II) amides via composite-hydroxide-mediated approach

Energy Technology Data Exchange (ETDEWEB)

Wan Buyong [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); College of Physics and Information Technology, Chongqing Normal University, Chongqing 400047 (China); Hu Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Liu Hong [State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China); Xiong Yufeng [National Center for Nanoscience and Technology, Beijing 100080 (China); Li Feiyun; Xi Yi; He Xiaoshan [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China)

2009-09-15

The pure face-centered-cubic PbTe nanorods have been synthesized by the composite-hydroxide-mediated approach using hydrazine as a reducing agent. The method is based on reaction among reactants in the melts of potassium hydroxide and sodium hydroxide eutectic at 170-220 deg. C and normal atmosphere without using any organic dispersant or surface-capping agent. Scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the structure, morphology and composition of the samples. The diameters of nanorods are almost fixed, while the lengths can be tunable under different growth time and temperatures. The growth mechanism of PbTe nanorods is investigated via UV-vis absorption, demonstrating that polymerized tellurium anions and metal(II) amides in the hydrazine hydroxide melts could control the crystallization and growth process of PbTe nanostructures. The band gap of as-synthesized PbTe nanorods has been calculated based on UV-vis-NIR optical diffuse reflectance spectra data.

The effect of various cations and pH on the adsorption of U(VI) on Amberlite IR-118H resin

International Nuclear Information System (INIS)

Kilislioglu, Ayben

2003-01-01

The effects of various metal cations and pH on the adsorption of uranium(VI) on strongly acidic cation exchanger Amberlite IR-118H (AIR-118H) were studied. The metal cations suppress U(VI) adsorption differently depending on their ionic radii. Adsorption of U(VI) on AIR-118H peaks at pH 3.4, which was attributed to the occurrence of different forms of U(VI) at different pH values. The adsorption data were then processed using the Frumkin-Fowler-Guggenheim equation, and the standard free energy of adsorption was calculated

Effect of increasing tellurium content on the electronic and optical properties of cadmium selenide telluride alloys CdSe{sub 1-x}Te{sub x}: An ab initio study

Energy Technology Data Exchange (ETDEWEB)

Reshak, Ali Hussain, E-mail: maalidph@yahoo.co.uk [Institute of Physical Biology-South Bohemia University, Nove Hrady 37333 (Czech Republic); School of Material Engineering, Malaysia University of Perlis, P.O Box 77, d/a Pejabat Pos Besar, 01007 Kangar, Perlis (Malaysia); Kityk, I.V. [Electrical Engineering Department, Technical University of Czestochowa, Al. Armii Krajowej 17/19, Czestochowa (Poland); Khenata, R. [Laboratoire de Physique Quantique et de Modelisation Mathematique de la Matiere (LPQ3 M), universite de Mascara, Mascara 29000 (Algeria); Department of Physics and Astronomy, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Auluck, S. [National Physical Laboratory Dr. K S Krishnan Marg, New Delhi 110012 (India)

2011-06-16

Highlights: > Theoretical study of effect of vary Te content on band structure, density of states, linear and nonlinear optical susceptibilities of CdSe{sub 1-x}Te{sub x}. > Increasing Te content leads to a decrease in the energy band gap. > Significant enhancement of the electronic properties as a function of tellurium concentration - Abstract: An all electron full potential linearized augmented plane wave method, within a framework of GGA (EV-GGA) approach, has been used for an ab initio theoretical study of the effect of increasing tellurium content on the band structure, density of states, and the spectral features of the linear and nonlinear optical susceptibilities of the cadmium-selenide-telluride ternary alloys CdSe{sub 1-x}Te{sub x} (x = 0.0, 0.25, 0.5, 0.75 and 1.0). Our calculations show that increasing Te content leads to a decrease in the energy band gap. We find that the band gaps are 0.95 (1.76), 0.89 (1.65), 0.83 (1.56), 0.79 (1.44) and 0.76 (1.31) eV for x = 0.0, 0.25, 0.5, 0.75 and 1.0 in the cubic structure. As these alloys are known to have a wurtzite structure for x less than 0.25, the energy gaps are 0.8 (1.6) eV and 0.7 (1.55) eV for the wurtzite structure (x = 0.0, 0.25) for the GGA (EV-GGA) exchange correlation potentials. This reduction in the energy gaps enhances the functionality of the CdSe{sub 1-x}Te{sub x} alloys, at least for these concentrations, leading to an increase in the effective second-order susceptibility coefficients from 16.75 pm/V (CdSe) to 18.85 pm/V (CdSe{sub 0.75}Te{sub 0.25}), 27.23 pm/V (CdSe{sub 0.5}Te{sub 0.5}), 32.25 pm/V (CdSe{sub 0.25}Te{sub 0.75}), and 37.70 pm/V (CdTe) for the cubic structure and from 12.65 pm/V (CdSe) to 21.11 pm/V (CdSe{sub 0.75}Te{sub 0.25}) in the wurtzite structure. We find a nonlinear relationship between the absorption/emission energies and composition, and a significant enhancement of the electronic properties as a function of tellurium concentration. This variation will help in

118-B-1 excavation treatability test procedures

International Nuclear Information System (INIS)

Frain, J.M.

1994-01-01

This treatability study has two purposes: to support development of the approach to be used for burial ground remediation, and to provide specific engineering information for the design of burial grounds receiving waste generated from the 100 Area removal actions. Data generated from this test will also provide performance and cost information necessary for detailed analysis of alternatives for burial ground remediation. Further details on the test requirements, milestones and data quality objectives are described in detail in the 118-B-1 Excavation Treatability Test Plan (DOE/RL-94-43). These working procedures are intended for use by field personnel to implement the requirements of the milestone. A copy of the detailed Test Plan will be kept on file at the on-site field support trailer, and will be available for review by field personnel

41 CFR 102-118.550 - How does a TSP file an administrative claim using EDI or other electronic means?

Science.gov (United States)

2010-07-01

... administrative claim using EDI or other electronic means? 102-118.550 Section 102-118.550 Public Contracts and... EDI or other electronic means? The medium and precise format of data for an administrative claim filed electronically must be approved in advance by the GSA Audit Division. GSA will use an authenticating EDI...

Experimental investigation of decay properties of neutron deficient $^{116-118}$Ba isotopes and test of $^{112-115}$Ba beam counts

CERN Multimedia

We propose to study decay of neutron deficient isotopes $^{116-118}$Ba using Double Sided Silicon Strip Detector (DSSSD). To study delayed-proton and $\\alpha$-decay branching ratios of $^{116-118}$Ba are of special interest because of their vicinity to the proton drip line. The nuclear life-times and properties of the proton unstable states of Cs isotopes, populated through decay of $^{116-118}$Ba isotopes will be measured. In addition to that we propose beam development of $^{112-115}$Ba to study exotic decay properties of these neutron deficient nuclei and to search for super-allowed $\\alpha$-decay in future.

Study on decay of 118Xe and 119Xe by means of mass-separator on-line with a synchrocyclotron

International Nuclear Information System (INIS)

Berlovich, Eh.E.; Batist, L.Kh.; Blinnikov, Yu.S.

1976-01-01

The decay of sup(118, 119)Xe isotopes has been investigated. An experimental device involving a mass-separator operating in line with a synchrocyclotron is briefly outlined. The elements to be investigated were isolated from a proton-irradiated target by the 'on-beam-chemistry' methods and transferred into the mass-separator ion source. The Xe separated ions are transported to detectors in an experimental ha ll. The energies and relative γ ray intensities of 118 Xe → 118 J and of 119 Xe → 119 J decays ar presented. The error of the γ ray energy determination does not exceed 0.6 keV. Obtained are the periods of half-life: for 118 Xe - (3.8+-0.9) min, for 119 Xe - (5.8+-0.3) min. The decay scheme for 119 Xe is made up. The scheme of 119 Xe levels is well inscribed into the general systematics of the J odd isotope levels. On the basis of obtained and known data the spin values are described to the 119 J levels

Enhancement of Thermoelectric Properties of PEDOT:PSS and Tellurium-PEDOT:PSS Hybrid Composites by Simple Chemical Treatment

Science.gov (United States)

Jin Bae, Eun; Hun Kang, Young; Jang, Kwang-Suk; Yun Cho, Song

2016-01-01

The thermoelectric properties of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and tellurium-PEDOT:PSS (Te-PEDOT:PSS) hybrid composites were enhanced via simple chemical treatment. The performance of thermoelectric materials is determined by their electrical conductivity, thermal conductivity, and Seebeck coefficient. Significant enhancement of the electrical conductivity of PEDOT:PSS and Te-PEDOT:PSS hybrid composites from 787.99 and 11.01 to 4839.92 and 334.68 S cm-1, respectively was achieved by simple chemical treatment with H2SO4. The power factor of the developed materials could be effectively tuned over a very wide range depending on the concentration of the H2SO4 solution used in the chemical treatment. The power factors of the developed thermoelectric materials were optimized to 51.85 and 284 μW m-1 K-2, respectively, which represent an increase of four orders of magnitude relative to the corresponding parameters of the untreated thermoelectric materials. Using the Te-PEDOT:PSS hybrid composites, a flexible thermoelectric generator that could be embedded in textiles was fabricated by a printing process. This thermoelectric array generates a thermoelectric voltage of 2 mV using human body heat.

Vapor space characterization of waste Tank 241-TX-118 (in situ): Results from samples collected on 9/7/94

International Nuclear Information System (INIS)

Thomas, B.L.; Clauss, T.W.; Ligotke, M.W.; Pool, K.H.; McVeety, B.D.; Olsen, K.B.; Fruchter, J.S.; Goheen, S.C.

1995-10-01

This report describes inorganic and organic analyses results from in situ samples obtained from the headspace of the Hanford waste storage Tank 241-TX-118 (referred to as Tank TX-118). The results described here were obtained to support safety and toxicological evaluations. A summary of the results for inorganic and organic analytes is listed in Table 1. Detailed descriptions of the results appear in the text. Quantitative results were obtained for the inorganic compounds ammonia (NH 3 ), nitrogen dioxide (NO 2 ), nitric oxide (NO), hydrogen cyanide (CHN), and water (H 2 O). Sampling for sulfur oxides (SO x ) was not requested. In addition, quantitative results were obtained for the 39 TO-14 compounds plus an additional 13 analytes. Hexane, normally included in the additional analytes, was removed because a calibration standard was not available during analysis of Tank TX-118 SUMMA trademark canisters. Of these, 12 were observed above the 5-ppbv reporting cutoff. Fourteen tentatively identified compounds (TICs) were observed above the reporting cutoff of (ca.) 10 ppbv and are reported with concentrations that are semiquantitative estimates based on internal-standard response factors. The 10 organic analytes with the highest estimated concentrations are listed in Table 1 and account for approximately 86% of the total organic components in Tank TX-118. Permanent gas analysis was not conducted on the tank-headspace samples. Tank TX-118 is on both the Ferrocyanide and Organic Watch List

An accurate redetermination of the 118Sn binding energy

International Nuclear Information System (INIS)

Borzakov, S.B.; Panteleev, Ts.Ts.; Telezhnikov, S.A.; Chrien, R.E.; Faikow-Stanczyk, H.; Grigor'ev, Yu.V.; Pospisil, S.; Smotritskij, L.M.

2001-01-01

The energy of well-known strong γ-line from 198 Au, the 'gold standard', has been modified in the light of new adjustments in the fundamental constants and the value of 411.80176(12) keV was determined which is 0.29 eV lower than the latest 1999 value. An energy calibration procedure for determining the neutron binding energy, B n , from complicated (n,γ)-spectra has been developed. A mathematically simple minimization function consisting only of terms having as parameters the coefficients of the energy calibration curve (polynomial) is used. A priori information about the relationships among the energies of different peaks on the spectrum was taken into account by a Monte Carlo simulation. The procedure was used in obtaining of B n for 118 Sn and 64 Cu. The γ-ray spectrum from thermal neutron radiative capture by 117 Sn has been measured on the IBR-2 pulsed reactor. γ-rays were detected by a 72 cm 2 HPGe-detector. B n for 64 Cu was obtained from two γ-spectra. One spectrum was measured on the IBR-2 by the same detector. The other spectrum was measured with a pair spectrometer at the Brookhaven High Flux Beam Reactor. From these two spectra B n for 64 Cu was determined equal to 7915.52(8) keV. The mean value of two most precise results of B n for 118 Sn was determined to be 9326.35(9) keV. The B n for 57Fe was determined to be 7646.08(9) keV

Design of 118 MHz twelfth harmonic cavity of APS PAR

International Nuclear Information System (INIS)

Kang, Y.W.; Kustom, R.L.; Bridges, J.F.

1992-01-01

Two radio frequency (RF) cavities are needed in the Positron Accumulator Ring (PAR) of the Advanced Photon Source. One is for the first harmonic frequency at 9.8 MHz, and the other is for the twelfth harmonic frequency at 118 MHz. This note reports on the design of the 118 MHz RF cavity. Computer models are used to find the mode frequencies, impedances, Q-factors, and field distributions in the cavity. The computer codes MAFIA, URMEL, and URMEL-T are useful tools which model and simulate the resonance characteristics of a cavity. These codes employ the finite difference method to solve Maxwell's equations. MAFIA is a three-dimensional problem solver and uses square patches to approximate the inner surface of a cavity. URMEL and URMEL-T are two-dimensional problem solvers and use rectangular and triangular meshes, respectively. URMEL-T and MAFIA can handle problems with arbitrary dielectric materials located inside the boundary. The cavity employs a circularly cylindrical ceramic window to limit the vacuum to the beam pipe. The ceramic window used in the modeling will have a wall thickness of 0.9 cm. This wall thickness is not negligible in determining the resonant frequencies of the cavity. In the following, results of two- and three-dimensional modeling of the cavities using the URMEL-T and MAFIA codes are reported

A novel small molecule FL118 that selectively inhibits survivin, Mcl-1, XIAP and cIAP2 in a p53-independent manner, shows superior antitumor activity.

Directory of Open Access Journals (Sweden)

Xiang Ling

Full Text Available Drug/radiation resistance to treatment and tumor relapse are major obstacles in identifying a cure for cancer. Development of novel agents that address these challenges would therefore be of the upmost importance in the fight against cancer. In this regard, studies show that the antiapoptotic protein survivin is a central molecule involved in both hurdles. Using cancer cell-based survivin-reporter systems (US 7,569,221 B2 via high throughput screening (HTS of compound libraries, followed by in vitro and in vivo analyses of HTS-derived hit-lead compounds, we identified a novel anticancer compound (designated FL118. FL118 shows structural similarity to irinotecan. However, while the inhibition of DNA topoisomerase 1 activity by FL118 was no better than the active form of irinotecan, SN-38 at 1 µM, FL118 effectively inhibited cancer cell growth at less than nM levels in a p53 status-independent manner. Moreover, FL118 selectively inhibited survivin promoter activity and gene expression also in a p53 status-independent manner. Although the survivin promoter-reporter system was used for the identification of FL118, our studies revealed that FL118 not only inhibits survivin expression but also selectively and independently inhibits three additional cancer-associated survival genes (Mcl-1, XIAP and cIAP2 in a p53 status-independent manner, while showing no inhibitory effects on control genes. Genetic silencing or overexpression of FL118 targets demonstrated a role for these targets in FL118's effects. Follow-up in vivo studies revealed that FL118 exhibits superior antitumor efficacy in human tumor xenograft models in comparison with irinotecan, topotecan, doxorubicin, 5-FU, gemcitabine, docetaxel, oxaliplatin, cytoxan and cisplatin, and a majority of mice treated with FL118 showed tumor regression with a weekly × 4 schedule. FL118 induced favorable body-weight-loss profiles (temporary and reversible and was able to eliminate large tumors. Together

Steady-State PMU Compliance Test under C37.118.1a-2014

DEFF Research Database (Denmark)

Ghiga, Radu; Wu, Qiuwei; Martin, Kenneth E.

2016-01-01

This paper presents a flexible testing method and the steady-state compliance of PMUs under the C37.118.1a amendment. The work is focused on the changes made to the standard for the harmonic rejection and out-of-band interference tests for which the ROCOF Error limits have been suspended. The paper...

Dynamic PMU Compliance Test under C37.118.1aTM-2014

DEFF Research Database (Denmark)

Ghiga, Radu; Wu, Qiuwei; Martin, K.

2015-01-01

This paper presents a flexible testing methodology and the dynamic compliance of PMUs as per the new C37.118.1a amendment published in 2014. The test platform consists of test signal generator, a Doble F6150 amplifier, PMUs under test, and a PMU test result analysis kit. The Doble amplifier is used...

29 CFR 4.118 - Contracts for carriage subject to published tariff rates.

Science.gov (United States)

2010-07-01

... Application of the McNamara-O'Hara Service Contract Act Specific Exclusions § 4.118 Contracts for carriage... carriage. The contracts excluded from the reach of the Act by this exemption are typically those where... 29 Labor 1 2010-07-01 2010-07-01 true Contracts for carriage subject to published tariff rates. 4...

How elements up to 118 were reached and how to go beyond

Science.gov (United States)

Düllmann, Christoph E.

2017-11-01

The new superheavy elements with Z=113, 115, 117, and 118 were recently accepted into the periodic table and have been named. Elements with Z≥112 are predominantly produced in 48Ca-induced fusion reactions on actinide targets. This pathway is exhausted at Z=118 due to the lack of target materials with sufficiently high proton number to reach elements with Z≥119. Search experiments for yet heavier elements were performed at GSI Darmstadt and FLNR Dubna. The reactions 50Ti + 249Bk, which leads to Z=119, as well as 64Ni + 238U, 58Fe + 244Pu, 54Cr + 248Cm, and 50Ti + 249Cf, leading to Z=120, have been studied. Despite a total duration of these experiments of more than one year, neither succeeded in the identification of a new element. To obtain improved guidance for better-informed search experiments, nuclear reaction studies appear necessary and have recently started. Also technical advances will be an important pillar to this end. At GSI, work towards a new continuous-wave linear accelerator is ongoing and is briefly described.

Selective adrenergic beta-2-receptor blocking drug, ICI-118.551, is effective in essential tremor.

Science.gov (United States)

Teräväinen, H; Huttunen, J; Larsen, T A

1986-07-01

Eighteen patients with essential tremor were treated for 2 days with a non-selective adrenergic beta-blocking drug (dl-propranolol, 80 mg X 3), a beta-2-selective blocker (ICI-118.551, 50 mg X 3) and placebo (X 3) in a randomized double blind cross-over study. Postural hand tremor was recorded with an accelerometer before administration of the drugs and at the end of each treatment period. Compared with placebo, both the beta-blocking drugs caused a statistically significant decrease in tremor intensity and they possessed approximately similar antitremor potency. Subjective benefit was reported by 12 of the 18 patients receiving ICI-118.551, 13 when on propranolol and 3 when on placebo.

Production and characterization Te-peptide by induced autolysis of Saccharomyces cerevisiae.

Science.gov (United States)

Morya, V K; Dong, Shin Jae; Kim, Eun-ki

2014-04-01

Recently, the interest in mimicking functions of chalcogen-based catalytic antioxidants like selenoenzymes, has been increased. Various attempts had been done with selenium, but very few attempts were carried out with tellurium. Bio-complex formation and characterization of tellurium was not tried earlier by using any organism. The present study was focused on tellurium peptide production, characterization, and bioactivity assessment especially Mimetic to glutathione peroxidase (GPx). The production was achieved by the autolysis of total proteins obtained from Saccharomyces cerevisiae ATCC 7752 grown with inorganic tellurium. The GPx-like activity of the hydrolyzed tellurium peptide was increased when prepared by autolysis, but decreased when prepared by acid hydrolysis. Tellurium peptide produced by autolysis of the yeast cell showed increased GPx-like activity as well as tellurium content. Tellurium peptide showed little toxicity, compared to highly toxic inorganic tellurium. The results showed the potential of tellurium peptide as an antioxidant that can be produced by simple autolysis of yeast cells.

Cleanup Verification Package for the 118-F-1 Burial Ground

Energy Technology Data Exchange (ETDEWEB)

E. J. Farris and H. M. Sulloway

2008-01-10

This cleanup verification package documents completion of remedial action for the 118-F-1 Burial Ground on the Hanford Site. This burial ground is a combination of two locations formerly called Minor Construction Burial Ground No. 2 and Solid Waste Burial Ground No. 2. This waste site received radioactive equipment and other miscellaneous waste from 105-F Reactor operations, including dummy elements and irradiated process tubing; gun barrel tips, steel sleeves, and metal chips removed from the reactor; filter boxes containing reactor graphite chips; and miscellaneous construction solid waste.

118-B-1 excavation treatability test plan

International Nuclear Information System (INIS)

1994-07-01

The Hanford 118-B-1 Burial Ground Treatability Study has been required by milestone change request number-sign M-15-93-04, dated September 30, 1993. The change request requires that a treatability test be conducted at the 100-B Area to obtain additional engineering information for remedial design of burial grounds receiving waste from 100 Area removal actions. This treatability study has two purposes: (1) to support development of the Proposed Plan (PP) and Record of Decision (ROD), which will identify the approach to be used for burial ground remediation, and (2) to provide specific engineering information for receiving waste generated from the 100 Area removal actions. Data generated from this test also will provide critical performance and cost information necessary for remedy evaluation in the detailed analysis of alternatives during preparation of the focused feasibility study (FFS). This treatability testing supports the following 100 Area alternatives: (1) excavation and disposal, and (2) excavation, sorting, (treatment), and disposal

How elements up to 118 were reached and how to go beyond

Directory of Open Access Journals (Sweden)

Düllmann Christoph E.

2017-01-01

Full Text Available The new superheavy elements with Z=113, 115, 117, and 118 were recently accepted into the periodic table and have been named. Elements with Z≥112 are predominantly produced in 48Ca-induced fusion reactions on actinide targets. This pathway is exhausted at Z=118 due to the lack of target materials with sufficiently high proton number to reach elements with Z≥119. Search experiments for yet heavier elements were performed at GSI Darmstadt and FLNR Dubna. The reactions 50Ti + 249Bk, which leads to Z=119, as well as 64Ni + 238U, 58Fe + 244Pu, 54Cr + 248Cm, and 50Ti + 249Cf, leading to Z=120, have been studied. Despite a total duration of these experiments of more than one year, neither succeeded in the identification of a new element. To obtain improved guidance for better-informed search experiments, nuclear reaction studies appear necessary and have recently started. Also technical advances will be an important pillar to this end. At GSI, work towards a new continuous-wave linear accelerator is ongoing and is briefly described.

Comparative Analysis of Supply Risk-Mitigation Strategies for Critical Byproduct Minerals: A Case Study of Tellurium.

Science.gov (United States)

Bustamante, Michele L; Gaustad, Gabrielle; Alonso, Elisa

2018-01-02

Materials criticality assessment is a screening framework increasingly applied to identify materials of importance that face scarcity risks. Although these assessments highlight materials for the implicit purpose of informing future action, the aggregated nature of their findings make them difficult to use for guidance in developing nuanced mitigation strategy and policy response. As a first step in the selection of mitigation strategies, the present work proposes a modeling framework and accompanying set of metrics to directly compare strategies by measuring effectiveness of risk reduction as a function of the features of projected supply demand balance over time. The work focuses on byproduct materials, whose criticality is particularly important to understand because their supplies are inherently less responsive to market balancing forces, i.e., price feedbacks. Tellurium, a byproduct of copper refining, which is critical to solar photovoltaics, is chosen as a case study, and three commonly discussed byproduct-relevant strategies are selected: dematerialization of end-use product, byproduct yield improvement, and end-of-life recycling rate improvement. Results suggest that dematerialization will be nearly twice as effective at reducing supply risk as the next best option, yield improvement. Finally, due to its infrequent use at present and its dependence upon long product lifespans, recycling end-of-life products is expected to be the least effective option despite potentially offering other benefits (e.g., cost savings and environmental impact reduction).

Enrichment mechanisms of tellurium in ferromanganese crusts

Science.gov (United States)

Sakaguchi, A.; Sugiyama, T.; Usui, A.; Takahashi, Y.

2012-04-01

Marine ferromanganese crusts (FMCs) consist of iron (Fe) hydroxides and manganese (Mn) oxides with various minor and trace elements. Especially for tellurium (Te), which is recognized as one of the rare metals, it has been reported that this element is concentrated about 105 times in FMCs compared with earth's crust, and the host phase might be Fe (oxy)hydroxide (Hein et al., 2003). Actually, in our previous study, the high concentration of Te in very surface layers of FMCs was found from the top to halfway down of a seamount in the Pacific Ocean. However, the concentration of Te in surface layers through the seamount showed good correlation with that of Mn instead of Fe. In this study, we attempted to clarify the enrichment mechanism of Te in FMCs with some methods including X-ray absorption fine structure (XAFS) technique for synthesised /natural samples. Seventeen FMC samples were collected from the Takuyo-Daigo seamount, from 950 m (summit) to 3000 m in water depth, with hyper-dolphin (remotely operated vehicle) equipped with live video camera and manipulators. The growth rates of all FMC samples were estimated to be about 3 mm/Ma. Very surface layer (less than 1 mm) of all FMC was analyzed with XRD and XAFS to confirm the mineral composition and speciation of Te. Furthermore, to serve as an aid to clarify the adsorption mechanism of Te on FMCs, distribution coefficients (Kd) and oxidation states were determined through the adsorption experiments of Te(IV) and Te(VI) on ferrihydrite and δ-MnO2. In all the experiments, pH and ionic strength were adjusted to pH 7.5 and 0.7 M, respectively. The oxidation state of Te in water phase was determined with HPLC-ICP-MS. As for the analysis of oxidation and adsorption states on the solid phase, XAFS was employed. The major mineral composition of Fe and Mn had no significant variation through the water depth of Takuyo-Daigo seamount. The oxidation state of Te in all samples showed hexavalent, and there was no significant

Loft CIS analysis 2''-LS-118-AB outside containment penetration S5-D

International Nuclear Information System (INIS)

Morton, D.K.

1978-01-01

A stress analysis was performed on the 2''-LS-118-AB pipe system outside containment penetration S5-D. Deadweight, thermal expansion, and seismic loads were considered. The results indicate that this piping will meet ASME Section III, Class 2 requirements provided a U-bolt (S4) is installed as indicated in this report

Comment on “Temperature dependence of atomic vibrations in mono-layer graphene” [J. Appl. Phys. 118, 074302 (2015)

International Nuclear Information System (INIS)

Susi, T.; Kotakoski, J.

2016-01-01

In an interesting recent study [Allen et al., J. Appl. Phys. 118, 074302 (2015)] (see also their Erratum [Allen et al., J. Appl. Phys. 118, 159902 (2015)]), Allen and co-workers measured the mean square amplitudes of graphene lattice vibrations between 100 and 1300 K and used a simplified theoretical approximation for the acoustic phonon modes to evaluate the maximum phonon wavelengths supported by the lattice. By fitting their data using the smallest wave-vector as the fitting parameter, they found this to be significantly smaller than the physical size of the graphene crystallites

Reaction of 1-bromo-3-chloropropane with tellurium and dimethyl telluride in the system of hydrazine hydrate-alkali; Reaktsiya 1-brom-3-khlorpropana s tellurom i dimetilditelluridom v sisteme gidrazin-gidrat-shcheloch'

Energy Technology Data Exchange (ETDEWEB)

Russavskaya, N V; Levanova, E P; Sukhomazova, Eh N; Grabel' nykh, V A; Elaev, A V; Klyba, L V; Zhanchipova, E R; Albanov, A I; Korotaeva, I M; Toryashinova, D S.D.; Korchevin, N A [SO RAN, Irkutskij Inst. Khimii imeni A.E. Favorskogo, Irkutsk (Russian Federation)

2006-05-15

A synthesis of oligomeric substance of thiocol type, the poly(trimethyleneditelluride), from 1-bromo-3-chloropropane and elemental tellurium is performed using a hydrazine hydrate-alkali system. Reductive splitting of the tellurocol followed by alkylation with methyl iodide give rise to preparation of bis(methyltelluro)propane, which was synthesized also from dimethyl telluride and 1,3-dihalopropanes using the N{sub 2}H{sub 4}{center_dot}H{sub 2}O/KOH system. The reaction products were characterized by elementary analysis, NMR, and IR spectra. Mass spectra of the synthesized low molecular weight organotellurium compounds are considered.

42 CFR 84.118 - Half-mask facepieces, full facepieces, and mouthpieces; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, and... OF RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.118 Half-mask facepieces, full facepieces, and mouthpieces; fit; minimum requirements. (a) Half-mask facepieces and full facepieces shall be designed and...

Acousto-optic control of internal acoustic reflection in tellurium dioxide crystal in case of strong elastic energy walkoff [Invited].

Science.gov (United States)

Voloshinov, Vitaly; Polikarpova, Nataliya; Ivanova, Polina; Khorkin, Vladimir

2018-04-01

Peculiar cases of acoustic wave propagation and reflection may be observed in strongly anisotropic acousto-optical crystals. A tellurium dioxide crystal serves as a prime example of such media, since it possesses record indexes of acoustic anisotropy. We studied one of the unusual scenarios of acoustic incidence and reflection from a free crystal-vacuum boundary in paratellurite. The directions of the acoustic waves in the (001) plane of the crystal were determined, and their basic characteristics were calculated. The carried-out acousto-optic experiment at the wavelength of light 532 nm and the acoustic frequency 73 MHz confirmed the theoretical predictions. The effects examined in the paper include the acoustic wave propagation with the record walkoff angle 74°. We also observed the incidence of the wave on the boundary at the angle exceeding 90°. Finally, we registered the close-to-back reflection of acoustic energy following the incidence. One of the stunning aspects is the distribution of energy between the incident and the back-reflected wave. The unusual features of the acoustic wave reflections pointed out in the paper are valuable for their possible applications in acousto-optic devices.

Synthesis of the isotopes of elements 118 and 116 in the 249Cf and 245Cm+48Ca fusion reactions

International Nuclear Information System (INIS)

Oganessian, Y T; Utyonkov, V K; Lobanov, Y V; Abdullin, F S; Polyakov, A N; Sagaidak, R N; Shirokovsky, I V; Tsyganov, Y S; Voinov, A A; Gulbekian, G G; Bogomolov, S L; Gikal, B N; Mezentsev, A N; Iliev, S; Subbotin, V G; Sukhov, A M; Subotic, K; Zagrebaev, V I; Vostokin, G K; Itkis, M G; Moody, K J; . Patin, J B; Shaughnessy, D A; Stoyer, M A; Stoyer, N J; Wilk, P A; Kenneally, J M; Landrum, J H; Wild, J F; Lougheed, R W

2006-01-01

The decay properties of 290 116 and 291 116, and the dependence of their production cross sections on the excitation energies of the compound nucleus, 293 116, have been measured in the 245 Cm( 48 Ca,xn) 293-x 116 reaction. These isotopes of element 116 are the decay daughters of element 118 isotopes, which are produced via the 249 Cf+ 48 Ca reaction. They performed the element 118 experiment at two projectile energies, corresponding to 297 118 compound nucleus excitation energies of E* = 29.2 ± 2.5 and 34.4 ± 2.3 MeV. During an irradiation with a total beam dose of 4.1 x 10 19 48 Ca projectiles, three similar decay chains consisting of two or three consecutive α decays and terminated by a spontaneous fission (SF) with high total kinetic energy of about 230 MeV were observed. The three decay chains originated from the even-even isotope 294 118 (E α = 11.65 ± 0.06 MeV, T α = 0.89 -0.31 +1.07 ms) produced in the 3n-evaporation channel of the 249 Cf+ 48 Ca reaction with a maximum cross section of 0.5 -0.3 +1.6 pb

A laser system for the spectroscopy on highly charged ions, tellurium molecules, and Rydberg states of rubidium atoms; Ein Lasersystem zur Spektroskopie von hochgeladenen Ionen, Tellurmolekuelen und Rubidium-Rydberg-Zustaenden

Energy Technology Data Exchange (ETDEWEB)

Albrecht, Sebastian

2014-08-15

Optical measuring methods allow the detection and identification of the atomic structure with extraordinary precision. Deviations to theoretical predictions can indicate unknown physical effects. Therefore, precise measurements on the atomic structure continue to be of large relevance. In this work, a laser system for precision spectroscopy on Bismuth ({sup 209}Bi{sup 82+}), Tellurium ({sup 130}Te{sub 2}) and Rydberg states of Rubidium ({sup 85}Rb) has been built and characterized. Spectroscopic measurements on Tellurium and Rubidium have been achieved with this setup. The system consists of a two-stage frequency doubled diode laser, stabilized via a cavity and an RF-offsetlock to arbitrary wavelengths with absolute high stability. The setup of the laser system will be presented and the systematic error caused by the refractive index of air inside the transfer cavity will be discussed. A stability of better then 6.14 MHz at 244 nm is obtained for planned experiments on the ground state hyperfine splitting of {sup 209}Bi{sup 82+}. This will allow an increase in precision of more then four orders of magnitude for this measurement. Further increase in precision can be achieved by using an evacuated cavity. The obtained stability is measured by comparison of the laser frequency to absorption lines of Tellurium ({sup 130}Te{sub 2}). Eight reference lines, known from literature, spanning the region from 613720.717 GHz to 616803.545 GHz have been measured. The frequency measurements of three lines, coinciding with the emission spectrum of an argon-ion-laser, show deviations with respect to the published frequencies. Further inconsistencies in literature are cleared. Part of this work is also the precise measurement of 843 Doppler-free {sup 130}Te{sub 2} reference lines spanning the frequency range from 613881.150 GHz to 616614.258 GHz at a precision of better then 4 MHz for most lines. Additionally, measurements on electromagnetically induced transparency (EIT) using

Yield of 117Sb, 118mSb, 120mSb, 122Sb, 124Sb in reactions Sn (p, xn)

International Nuclear Information System (INIS)

Dmitriev, P.P.; Konstantinov, I.O.

1993-01-01

Yield of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb from thick target depending on proton energy is measured. The maximum proton energy is 21.7±0.2 MeV. Antimony isotopes yield in separate reactions when irradiating of tin isotopes with 100% enrichment is determined using the method published earlier. The methods for production of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb with high radioisotope purity are shown. 13 refs., 1 fig., 3 tabs

Cleanup Verification Package for the 118-F-3, Minor Construction Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.

2007-01-01

This cleanup verification package documents completion of remedial action for the 118-F-3, Minor Construction Burial Ground waste site. This site was an open field covered with cobbles, with no vegetation growing on the surface. The site received irradiated reactor parts that were removed during conversion of the 105-F Reactor from the Liquid 3X to the Ball 3X Project safety systems and received mostly vertical safety rod thimbles and step plugs

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses.

Science.gov (United States)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-05-19

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO(2))(1 - x)(ZnO)(x) (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T(g) has been determined for each glass, showing a monotonous decrease of T(g) with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T(d) very close to the respective T(g) values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T(g) in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T(g) and confirms the correlation between the BP and the MRO of glasses.

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses

International Nuclear Information System (INIS)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T g has been determined for each glass, showing a monotonous decrease of T g with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T d very close to the respective T g values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T g in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T g and confirms the correlation between the BP and the MRO of glasses.

Determination of diacylhydrazines-type insect growth regulator JS-118 residues in cabbage and soil by high performance liquid chromatography with DAD detection.

Science.gov (United States)

Hu, J-Y; Deng, Z-B; Qin, D-M

2009-12-01

JS-118 is a diacylhydrazines-type insect growth regulator used extensively in China now. An analytical method for residues determination of JS-118 in cabbage and soil samples by high performance liquid chromatography with DAD detection was established and optimized. Primary secondary amine solid phase extraction cartridge was used for sample preparation. Mean recoveries for the analyte ranged from 96.6% to 107.0% with CV value less than 4.7%. The limit of quantification is 0.01 mg/kg. Direct confirmation of JS-118 residues in samples was realized by high performance liquid chromatography-mass spectrometry. The proposed method is simple, rapid and reliable to perform and could be utilized for monitoring of pesticides residues.

A neutron diffraction study of pyridinium-1-dicyanomethylide, C8D5N3, at 294 K and 118 K

International Nuclear Information System (INIS)

Devos, L.; Baert, F.; Fouret, R.; Thomas, M.

1980-01-01

A neutron diffraction study of perdeuterated pyridium-1-dicyanomethylide has been carried out at room temperature and at 118 K at the high-flux beam reactor of the Institut Laue-Langevin. Low temperature was obtained with a cryostat based on the Joule-Thomson expansion of gaseous helium, with a maximum long-term variation of +-1 K. The crystals are monoclinic, space group P2 1 /m. The data refinements, including extinction parameters, gave final Rsub(w)(F 2 ) values of 0.038 (RT, 552 independent reflections) and 0.028 (118 K, 1869 independent reflections). A TLS thermal analysis indicated rigid-body behaviour of the non-deuterium atoms. The non-planarity of the molecule was confirmed. The bond distances were corrected for thermal motion and their e.s.d.'s ranged from 0.0012 to 0.0030 A (RT) and from 0.0003 to 0.0008 A (118 K). (Auth.)

Cold fusion valleys for the synthesis of Z=118 isotopes

International Nuclear Information System (INIS)

Gherghescu, R.

2005-01-01

Cold fusion reactions are investigated with the goal to synthesize Z=118 isotopes with neutron numbers N=162, 168, 172, 176. Potential energy surfaces are calculated as the result of dynamic minimization with independent deformations of the target and projectile, small semi-axis of the projectile and distance between centers as degrees of freedom. An advanced binary macroscopic-microscopic method is used to obtain the deformation energy and the Werner-Wheeler approximation yield the mass tensor. Charge asymmetry is varied for the same mass asymmetry channel which belongs to a given energy valley. The highest penetrability values are obtained for cold fusion channels with Sn, Te and Xe isotopes as projectiles

Cleanup Verification Package for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault

International Nuclear Information System (INIS)

Appel, M.J.

2006-01-01

This cleanup verification package documents completion of remedial action for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault. The site consisted of an inactive solid waste storage vault used for temporary storage of slightly contaminated reactor parts that could be recovered and reused for the 100-F Area reactor operations

Cleanup Verification Package for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault

Energy Technology Data Exchange (ETDEWEB)

M. J. Appel

2006-11-02

This cleanup verification package documents completion of remedial action for the 118-F-7, 100-F Miscellaneous Hardware Storage Vault. The site consisted of an inactive solid waste storage vault used for temporary storage of slightly contaminated reactor parts that could be recovered and reused for the 100-F Area reactor operations.

Vapor space characterization of waste tank 241-TX-118: Results from samples collected on 12/16/94

International Nuclear Information System (INIS)

Lucke, R.B.; Ligotke, M.W.; McVeety, B.D.

1995-10-01

This report describes inorganic and organic analyses results from samples obtained from the headspace of the Hanford waste storage Tank 241-TX-118 (referred to as Tank TX-118). The results described here were obtained to support safety and toxicological evaluations. A summary of the results for inorganic and organic analytes is listed in Table 1. Detailed descriptions of the results appear in the text. Quantitative results were obtained for the inorganic compounds ammonia (NH 3 ), nitrogen dioxide (NO 2 ), nitric oxide (NO), and water (H 2 O). Sampling for hydrogen cyanide (HCN) and sulfur oxides (SO x ) was not requested. In addition, quantitative results were obtained for the 39 TO-14 compounds plus an additional 14 analytes. Of these, 3 were observed above the 5-ppbv reporting cutoff. Twenty three organic tentatively identified compounds (TICs) were observed above the reporting cutoff of (ca.) 10 ppbv, and are reported with concentrations that are semiquantitative estimates based on internal-standard response factors. The 10 organic analytes with the highest estimated concentrations are listed in Table 1 and account for approximately 84% of the total organic components in Tank TX-118. Two permanent gases, carbon dioxide (CO 2 ) and nitrous oxide (N 2 O), were also detected

Tank 241-TX-118, core 236 analytical results for the final report

International Nuclear Information System (INIS)

ESCH, R.A.

1998-01-01

This document is the analytical laboratory report for tank 241-TX-118 push mode core segments collected between April 1, 1998 and April 13, 1998. The segments were subsampled and analyzed in accordance with the Tank 241-TX-118 Push Mode Core sampling and Analysis Plan (TSAP) (Benar, 1997), the Safety Screening Data Quality Objective (DQO) (Dukelow, et al., 1995), the Data Quality Objective to Support Resolution of the Organic Complexant Safety Issue (Organic DQO) (Turner, et al, 1995) and the Historical Model Evaluation Data Requirements (Historical DQO) (Sipson, et al., 1995). The analytical results are included in the data summary table (Table 1). None of the samples submitted for Differential Scanning Calorimetry (DSC) and Total Organic Carbon (TOC) exceeded notification limits as stated in the TSAP (Benar, 1997). One sample exceeded the Total Alpha Activity (AT) analysis notification limit of 38.4microCi/g (based on a bulk density of 1.6), core 236 segment 1 lower half solids (S98T001524). Appropriate notifications were made. Plutonium 239/240 analysis was requested as a secondary analysis. The statistical results of the 95% confidence interval on the mean calculations are provided by the Tank Waste Remediation Systems Technical Basis Group in accordance with the Memorandum of Understanding (Schreiber, 1997) and are not considered in this report

34 CFR 97.118 - Applications and proposals lacking definite plans for involvement of human subjects.

Science.gov (United States)

2010-07-01

... Education PROTECTION OF HUMAN SUBJECTS Federal Policy for the Protection of Human Subjects (Basic ED Policy for Protection of Human Research Subjects) § 97.118 Applications and proposals lacking definite plans..., or contracts are submitted to departments or agencies with the knowledge that subjects may be...

Efficacy of PLD-118, a novel inhibitor of candida isoleucyl-tRNA synthetase, against experimental oropharyngeal and esophageal candidiasis caused by fluconazole-resistant C. albicans.

Science.gov (United States)

Petraitis, Vidmantas; Petraitiene, Ruta; Kelaher, Amy M; Sarafandi, Alia A; Sein, Tin; Mickiene, Diana; Bacher, John; Groll, Andreas H; Walsh, Thomas J

2004-10-01

PLD-118, formerly BAY 10-8888, is a synthetic antifungal derivative of the naturally occurring beta-amino acid cispentacin. We studied the activity of PLD-118 in escalating dosages against experimental oropharyngeal and esophageal candidiasis (OPEC) caused by fluconazole (FLC)-resistant Candida albicans in immunocompromised rabbits. Infection was established by fluconazole-resistant (MIC > 64 microg/ml) clinical isolates from patients with refractory esophageal candidiasis. Antifungal therapy was administered for 7 days. Study groups consisted of untreated controls; animals receiving PLD-118 at 4, 10, 25, or 50 mg/kg of body weight/day via intravenous (i.v.) twice daily (BID) injections; animals receiving FLC at 2 mg/kg/day via i.v. BID injections; and animals receiving desoxycholate amphotericin B (DAMB) i.v. at 0.5 mg/kg/day. PLD-118- and DAMB-treated animals showed a significant dosage-dependent clearance of C. albicans from the tongue, oropharynx, and esophagus in comparison to untreated controls (P 118 demonstrated nonlinear plasma pharmacokinetics across the investigated dosage range, as was evident from a dose-dependent increase in plasma clearance and a dose-dependent decrease in the area under the plasma concentration-time curve. The biochemical safety profile was similar to that of FLC. In summary, PLD-118 demonstrated dosage-dependent antifungal activity and nonlinear plasma pharmacokinetics in treatment of experimental FLC-resistant oropharyngeal and esophageal candidiasis.

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

Energy Technology Data Exchange (ETDEWEB)

M. J. Appel and J. M. Capron

2007-07-25

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes.

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.; Capron, J.M.

2007-01-01

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes

41 CFR 102-118.305 - Must my agency notify the TSP of any adjustment to the TSP's bill?

Science.gov (United States)

2010-07-01

... number, amount billed, amount paid, payment voucher number, complete tender or tariff authority... REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Prepayment Audits of Transportation Services...

On the study of proton-irradiated Tellurium targets relevant for production of medical radioisotopes 123I and 124I

International Nuclear Information System (INIS)

Imam Kambali; Hari Suryanto; Daya Agung Sarwono; Cahyana Amiruddin

2014-01-01

The energy loss distribution and range of energetic proton beams in tellurium (Te) target have been simulated using the Stopping and Range of Ion in Matter (SRIM 2013) codes. The calculated data of the proton's range were then used to determine the optimum thickness of Te targets for future production of 123 I and 124 I from 123 Te(p,n) 123 I, 124 Te(p,n) 124 I and 124 Te(p,2n) 123 I nuclear reactions using the BATAN's Cs-30 cyclotron. It was found that for an incidence angle of 0° with respect to the target normal, the optimum thickness of 123 Te and 124 Te targets for 123 I production should be 644 µm and 1.8 mm respectively, whereas a 649 µm thick 124 Te target would be Required for 124 I production. In addition, the thickness should be decreased with increasing incidence angle. The EOB yield could theoretically reach up to 13.62 Ci of 123 I at proton energy of 22 Me V and beam current of 30 µA if the 124 Te is irradiated over a period of 3 hours. The theoretical EOB yield is comparable to the experimental data with accuracy within 10%. (author)

CYP79 P450 monooxygenases in gymnosperms: CYP79A118 is associated with the formation of taxiphyllin in Taxus baccata.

Science.gov (United States)

Luck, Katrin; Jia, Qidong; Huber, Meret; Handrick, Vinzenz; Wong, Gane Ka-Shu; Nelson, David R; Chen, Feng; Gershenzon, Jonathan; Köllner, Tobias G

2017-09-01

Conifers contain P450 enzymes from the CYP79 family that are involved in cyanogenic glycoside biosynthesis. Cyanogenic glycosides are secondary plant compounds that are widespread in the plant kingdom. Their biosynthesis starts with the conversion of aromatic or aliphatic amino acids into their respective aldoximes, catalysed by N-hydroxylating cytochrome P450 monooxygenases (CYP) of the CYP79 family. While CYP79s are well known in angiosperms, their occurrence in gymnosperms and other plant divisions containing cyanogenic glycoside-producing plants has not been reported so far. We screened the transcriptomes of 72 conifer species to identify putative CYP79 genes in this plant division. From the seven resulting full-length genes, CYP79A118 from European yew (Taxus baccata) was chosen for further characterization. Recombinant CYP79A118 produced in yeast was able to convert L-tyrosine, L-tryptophan, and L-phenylalanine into p-hydroxyphenylacetaldoxime, indole-3-acetaldoxime, and phenylacetaldoxime, respectively. However, the kinetic parameters of the enzyme and transient expression of CYP79A118 in Nicotiana benthamiana indicate that L-tyrosine is the preferred substrate in vivo. Consistent with these findings, taxiphyllin, which is derived from L-tyrosine, was the only cyanogenic glycoside found in the different organs of T. baccata. Taxiphyllin showed highest accumulation in leaves and twigs, moderate accumulation in roots, and only trace accumulation in seeds and the aril. Quantitative real-time PCR revealed that CYP79A118 was expressed in plant organs rich in taxiphyllin. Our data show that CYP79s represent an ancient family of plant P450s that evolved prior to the separation of gymnosperms and angiosperms. CYP79A118 from T. baccata has typical CYP79 properties and its substrate specificity and spatial gene expression pattern suggest that the enzyme contributes to the formation of taxiphyllin in this plant species.

Stability indicating studies on NMITLI 118RT+ (standardized extract of withania somnifera dunal)

OpenAIRE

Ahmad, Hafsa; Khandelwal, Kiran; Pachauri, Shakti Deep; Sanghwan, Rajender Singh; Dwivedi, Anil Kumar

2014-01-01

Background: Withania somnifera Dunal (Ashwagandha) is an Indian medicinal plant of great medicinal value; used in many clinically proven conditions. NMITLI-118RT+ is a candidate drug under a Council of Scientific and Industrial Research (CSIR) networking project. It is a chemotype of W. somnifera's root extract, which has been used for the present study. Objectives: The present investigation aims to develop and validate a simple isocratic reverse phase-high performance liquid chromatography (...

High-power parametric amplification of 11.8-fs laser pulses with carrier-envelope phase control

NARCIS (Netherlands)

Zinkstok, R.T.; Witte, S.; Hogervorst, W.; Eikema, K.S.E.

2005-01-01

Phase-stable parametric chirped-pulse amplification of ultrashort pulses from a carrier-envelope phase-stabilized mode-locked Ti:sapphire oscillator (11.0 fs) to 0.25 mJ/pulse at 1 kHz is demonstrated. Compression with a grating compressor and a LCD shaper yields near-Fourier-limited 11.8-fs pulses

Wind tunnel tests of Risø-B1-18 and Risø-B1-24

DEFF Research Database (Denmark)

Fuglsang, P.; Bak, Christian; Gaunaa, Mac

2003-01-01

This report contains 2D measurements of the Risø-B1-18 and Risø-B1-24 airfoils. The aerodynamic properties were derived from pressure measurements on the airfoil surface and in the wake. The measurements were conducted in the VELUX open jet wind tunnel,which has a background turbulence intensity...

Tellurium sulfates from reactions in oleum and sulfur trioxide: syntheses and crystal structures of TeO(SO_4), Te_4O_3(SO_4)_5, and Te(S_2O_7)_2

International Nuclear Information System (INIS)

Logemann, Christian; Bruns, Joern; Schindler, Lisa Verena; Zimmermann, Vanessa; Wickleder, Mathias S.

2015-01-01

The reaction of K_2TeO_4 with fuming sulfuric acid (65 % SO_3) in sealed glass ampoules at 250 C led to colorless single crystals of TeO(SO_4) [triclinic, P anti 1, Z = 8, a = 819.89(3) pm, b = 836.95(4) pm, c = 1179.12(5) pm, α = 82.820(2) , β = 70.645(2) , γ = 81.897(2) , V = 753.11(6) x 10"6 pm"3]. A horseshoe type [Te_4O_3] fragment is the basic motif in the layer structure of the compound. The [Te_4O_3] moieties are linked to infinite chains by further oxide ions. Monomeric [Te_4O_3] horseshoes are found in the crystal structure of Te_4O_3(SO_4)_5 [trigonal, P3_221, Z = 3, a = 859.05(2) pm, c = 2230.66(7) pm, V = 1425.61(6) x 10"6 pm"3], which was obtained from TeO_2 and fuming sulfuric acid (65 % SO_3) at 200 C as colorless single crystals. By switching to neat SO_3 as reaction medium colorless crystals of Te(S_2O_7)_2 [P2_1/n, Z = 4, a = 1065.25(3) pm, b = 818.50(2) pm, c = 1206.27(3) pm, β = 102.097(1) , V = 1028.40(5) x 10"6 pm"3] form when ortho-telluric acid, H_6TeO_6, is used as the tellurium source. The compound was reported previously, however, obviously with a wrong crystallographic description. In the crystal structure the tellurium atoms are coordinated by two chelating disulfate ions. Further Te-O contacts link the [Te(S_2O_7)_2] units to an extended network. (Copyright copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

AmyI-1-18, a cationic α-helical antimicrobial octadecapeptide derived from α-amylase in rice, inhibits the translation and folding processes in a protein synthesis system.

Science.gov (United States)

Taniguchi, Masayuki; Ochiai, Akihito; Fukuda, Shun; Sato, Teppei; Saitoh, Eiichi; Kato, Tetsuo; Tanaka, Takaaki

2016-10-01

In our previous study, we used a cell-free rapid translation system (RTS), which is an in vitro protein synthesis system based on Escherichia coli lysate, for evaluating the inhibition of green fluorescent protein (GFP) synthesis by pyrrhocoricin. In this study, using an RTS, we evaluated the inhibition of GFP synthesis by AmyI-1-18, an antimicrobial octadecapeptide. We found that, similarly to pyrrhocoricin, AmyI-1-18 inhibited GFP synthesis in the RTS in a concentration-dependent manner. In addition, the blockage of transcription and translation steps in the RTS was individually estimated using RT-PCR after gene expression to determine the mRNA products and using sodium dodecyl sulfate-polyacrylamide gel electrophoresis to determine the amounts of GFP expressed from purified mRNA, respectively. The results demonstrated that the inhibition of GFP synthesis by AmyI-1-18 did not occur at the transcription step but rather at the translation step. Furthermore, we assessed the inhibition of DnaK-mediated refolding of chemically denatured luciferase by AmyI-1-18; AmyI-1-18 inhibited the protein folding activity of the ATP-dependent DnaK/DnaJ molecular chaperone system in a concentration-dependent manner. Surface plasmon resonance (SPR) analysis showed that AmyI-1-18 strongly bound to RNA with a KD value of 1.4 × 10(-8) M but not to DNA and that AmyI-1-18 specifically bound to DnaK with a KD value of 4.4 × 10(-6) M. These SPR analysis results supported the results obtained in both the RTS and the molecular chaperone system. These results demonstrated that both RNA and DnaK are most likely the target of AmyI-1-18 in the protein synthesis system. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Chemical processes for the extreme enrichment of tellurium into marine ferromanganese oxides

Science.gov (United States)

Kashiwabara, Teruhiko; Oishi, Yasuko; Sakaguchi, Aya; Sugiyama, Toshiki; Usui, Akira; Takahashi, Yoshio

2014-04-01

Tellurium, an element of growing economic importance, is extremely enriched in marine ferromanganese oxides. We investigated the mechanism of this enrichment using a combination of spectroscopic analysis and adsorption/coprecipitation experiments. X-ray Absorption Near-Edge Structure (XANES) analysis showed that in adsorption/coprecipitation systems, Te(IV) was oxidized on δ-MnO2 and not oxidized on ferrihydrite. Extended X-ray Absorption Fine Structure (EXAFS) analysis showed that both Te(IV) and Te(VI) were adsorbed on the surface of δ-MnO2 and ferrihydrite via formation of inner-sphere complexes. In addition, Te(VI) can be structurally incorporated into the linkage of Fe octahedra through a coprecipitation process because of its molecular geometry that is similar to the Fe octahedron. The largest distribution coefficient obtained in the adsorption/coprecipitation experiments was for the Te(VI)/ferrihydrite coprecipitation system, and it was comparable to those calculated from the distribution between natural ferromanganese oxides and seawater. Our XAFS and micro-focused X-ray fluorescence (μ-XRF) mapping of natural ferromanganese oxides showed that Te was structurally incorporated as Te(VI) in Fe (oxyhydr)oxide phases. We conclude that the main process for the enrichment of Te in ferromanganese oxides is structural incorporation of Te(VI) into Fe (oxyhydr)oxide phases through coprecipitation. This mechanism can explain the unique degree of enrichment of Te compared with other oxyanions, which are mainly enriched via adsorption on the surface of the solid structures. In particular, the great contrast in the distributions of Te and Se is caused by their oxidized species: (i) the similar geometry of the Te(VI) molecule to Fe octahedron, and (ii) quite soluble nature of Se(VI). Coexisting Mn oxide phases may promote structural incorporation of Te(VI) by oxidation of Te(IV), although the surface oxidation itself may not work as the critical enrichment process as

Boiling points of the superheavy elements 117 and 118

International Nuclear Information System (INIS)

Takahashi, N.

2001-01-01

It has been shown that the relativistic effect on the electrons reveal in the heavy element region. What kind of changes will appear in the heavy elements because of the relativistic effects? Can we observe the changes? We observed that the boiling points of astatine and radon are lower than that extrapolated values from lighter elements in the same groups. Systematic behavior of the elements on the boiling point was examined and a new method for the estimation of the boiling points of the superheavy elements in the halogen and rare gases has been found. The estimated values of the elements 117 and 118 are 618 and 247 K, respectively which are considerably lower than those obtained until now. If these values are correct the production of the superheavy elements with heavy ions reaction may be affected. Further, the chemical properties may be fairly different from the lighter elements. (author)

Loft CIS analysis 2''-LS-118-AB outside containment penetration S5-D

Energy Technology Data Exchange (ETDEWEB)

Morton, D.K.

1978-09-28

A stress analysis was performed on the 2''-LS-118-AB pipe system outside containment penetration S5-D. Deadweight, thermal expansion, and seismic loads were considered. The results indicate that this piping will meet ASME Section III, Class 2 requirements provided a U-bolt (S4) is installed as indicated in this report.

41 CFR 102-118.430 - What information must be on my agency's transportation bills submitted for a postpayment audit?

Science.gov (United States)

2010-07-01

... Reference Number; (e) The amount requested; (f) The amount paid; (g) The payment voucher number; (h...) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Postpayment...

19 CFR 118.21 - Temporary suspension; permanent revocation of selection and cancellation of agreement to operate...

Science.gov (United States)

2010-04-01

... appeal procedures provided under § 118.23. (c) Circumstance of change in employment not a bar to adverse action. Any change in the employment status of a corporate officer (for example, discharge, resignation... safeguard merchandise within the CES; (4) The CES operator fails to furnish a current list of names...

41 CFR 102-118.320 - What information must be on transportation bills that have completed my agency's prepayment audit?

Science.gov (United States)

2010-07-01

... amount billed; (6) The amount paid; (7) The payment voucher number; (8) Complete tender or tariff...) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Prepayment Audits of...

Leaching of cadmium and tellurium from cadmium telluride (CdTe) thin-film solar panels under simulated landfill conditions.

Science.gov (United States)

Ramos-Ruiz, Adriana; Wilkening, Jean V; Field, James A; Sierra-Alvarez, Reyes

2017-08-15

A crushed non-encapsulated CdTe thin-film solar cell was subjected to two standardized batch leaching tests (i.e., Toxicity Characteristic Leaching Procedure (TCLP) and California Waste Extraction Test (WET)) and to a continuous-flow column test to assess cadmium (Cd) and tellurium (Te) dissolution under conditions simulating the acidic- and the methanogenic phases of municipal solid waste landfills. Low levels of Cd and Te were solubilized in both batch leaching tests (<8.2% and <3.6% of added Cd and Te, respectively). On the other hand, over the course of 30days, 73% of the Cd and 21% of the Te were released to the synthetic leachate of a continuous-flow column simulating the acidic landfill phase. The dissolved Cd concentration was 3.24-fold higher than the TCLP limit (1mgL -1 ), and 650-fold higher than the maximum contaminant level established by the US-EPA for this metal in drinking water (0.005mgL -1 ). In contrast, the release of Cd and Te to the effluent of the continuous-flow column simulating the methanogenic phase of a landfill was negligible. The remarkable difference in the leaching behavior of CdTe in the columns is related to different aqueous pH and redox conditions promoted by the microbial communities in the columns, and is in agreement with thermodynamic predictions. Copyright © 2017 Elsevier B.V. All rights reserved.

Formation of tellurium nanocrystals during anaerobic growth of bacteria that use Te oxyanions as respiratory electron acceptors

Science.gov (United States)

Baesman, S.M.; Bullen, T.D.; Dewald, J.; Zhang, Dongxiao; Curran, S.; Islam, F.S.; Beveridge, T.J.; Oremland, R.S.

2007-01-01

Certain toxic elements support the metabolism of diverse prokaryotes by serving as respiratory electron acceptors for growth. Here, we demonstrate that two anaerobes previously shown to be capable of respiring oxyanions of selenium also achieve growth by reduction of either tellurate [Te(VI)] or tellurite [Te(IV)] to elemental tellurium [Te(0)]. This reduction achieves a sizeable stable-Te-isotopic fractionation (isotopic enrichment factor [??] = -0.4 to -1.0 per ml per atomic mass unit) and results in the formation of unique crystalline Te(0) nanoarchitectures as end products. The Te(0) crystals occur internally within but mainly externally from the cells, and each microorganism forms a distinctly different structure. Those formed by Bacillus selenitireducens initially are nanorods (???10-nm diameter by 200-nm length), which cluster together, forming larger (???1,000-nm) rosettes composed of numerous individual shards (???100-nm width by 1,000-nm length). In contrast, Sulfurospirillium barnesii forms extremely small, irregularly shaped nanospheres (diameter < 50 nm) that coalesce into larger composite aggregates. Energy-dispersive X-ray spectroscopy and selected area electron diffraction indicate that both biominerals are composed entirely of Te and are crystalline, while Raman spectroscopy confirms that they are in the elemental state. These Te biominerals have specific spectral signatures (UV-visible light, Raman) that also provide clues to their internal structures. The use of microorganisms to generate Te nanomaterials may be an alternative for bench-scale syntheses. Additionally, they may also generate products with unique properties unattainable by conventional physical/chemical methods. Copyright ?? 2007, American Society for Microbiology. All Rights Reserved.

BabelFish-Tools for IEEE C37.118.2-compliant real-time synchrophasor data mediation

Science.gov (United States)

Almas, M. S.; Vanfretti, L.; Baudette, M.

BabelFish (BF) is a real-time data mediator for development and fast prototyping of synchrophasor applications. BF is compliant with the synchrophasor data transmission IEEE Std C37.118.2-2011. BF establishes a TCP/IP connection with any Phasor Measurement Unit (PMU) or Phasor Data Concentrator (PDC) stream and parses the IEEE Std C37.118.2-2011 frames in real-time to provide access to raw numerical data in the LabVIEW environment. Furthermore, BF allows the user to select "data-of-interest" and transmit it to either a local or remote application using the User Datagram Protocol (UDP) in order to support both unicast and multicast communication. In the power systems Wide Area Monitoring Protection and Control (WAMPAC) domain, BF provides the first Free/Libre and Open Source Software (FLOSS) for the purpose of giving the users tools for fast prototyping of new applications processing PMU measurements in their chosen environment, thus liberating them of time consuming synchrophasor data handling and allowing them to develop applications in a modular fashion, without a need of a large and monolithic synchrophasor software environment.

Wind tunel tests of Risoe-B1-18 and Risoe-B1-24

Energy Technology Data Exchange (ETDEWEB)

Fuglsang, P.; Bak, C.; Gaunaa, M.; Antoniou, I.

2003-01-01

This report contains 2D measurements of the Risoe-B1-18 and Risoe-B1-24 airfoils. The aerodynamic properties were derived from pressure measurements on the airfoil surface and in the wake. The measurements were conducted in the VELUX open jet wind tunnel, which has a background turbulence intensity of 1%, and an inlet flow velocity of 42 m/s. The airfoil sections had a chord of 0.600 m giving a Reynolds number of 1.6Oe106. The span was 1.9 m and end plates were used to minimize 3D flow effects. The measurements comprised both static and dynamic inflow. Static inflow covered angles of attack from 5o to 30 deg. Dynamic inflow was obtained by pitching the airfoil in a harmonic motion around various mean angles of attack. The test matrix involved smooth flow, various kinds of leading edge roughness, stall strips, vortex generators and Gurney flaps in different combinations. The quality of the measurements was good and the agreement between measurements and numerical CFD predictions with EllipSys2D was good. For both airfoils predictions with turbulent flow captured very well the shapes of lift and drag curves as well as the magnitude of maximum lift. Measurements of Risoe-B1-18 showed that the maximum lift coefficient was 1.64 at an angle of attack of approximately 13 deg. The airfoil was not very sensitive to leading edge roughness despite its high maximum lift. Measurements with stall strips showed that stall strips could control the level of maximum lift. The Risoe-B1-24 measurements showed that the maximum lift coefficient was 1.62 at an angle of attack of approximately 14 deg. The airfoil was only little sensitive to leading edge roughness despite its high relative thickness and high maximum lift. Measurements with delta wing shaped vortex generators increased the maximum lift coefficient to 2.02 and measurements with Gurney flaps increased the maximum lift coefficient to 1.85. Measurements with combination of vortex generators and Gurney flaps showed a maximum

Evidence of parity violation in 118Sn and 36Cl

International Nuclear Information System (INIS)

Benkoula, H.

1978-01-01

Parity violation in nuclear systems was studied by forward-backward asymmetry measurement methods in radiative capture of polarized neutrons in the reactions 117 Sn(n,γ) 118 Sn and 35 Cl(n,γ) 36 Cl. The experimental set ups used two INa detectors situated at left and right sides of the beam and parallel to polarisation direction, and an electronic system adapted to high-counting rate. The asymmetry measurement, A=(4.56+-0.6)x10 -4 in the 9.328 MeV Ml transition demonstrates the existence of parity violation effects. The 8.58 MeV (M1+E2) transition in 36 Cl was also studied and the asymmetry value is A=(1.11+-0.35)x10 -4 . Several beam and electronic tests have shown that there was no spurious asymmetry in the measurement due to the equipment [fr

Electromagnetic E2 Transition Probabilities in 120Xe And 118Te - N=66 Nuclei

International Nuclear Information System (INIS)

Pasternak, A.A.; Efimov, A.D.; Podsvirova, E.O.

2001-01-01

Lifetimes of the yrast states in 120 Xe and the ground state band below and above band crossing in 118 Te have been measured by DSAM in the 111 Cd( 12 C, 3n) reaction and by DSAM and RDM in the 109 Ag( 13 C, p3n) reaction, respectively. The experimental data are compared with calculation done in the framework of the IBM1 model in the 0(6) and SU(5) limits. (author)

36 CFR 223.118 - Appeal process for small business timber sale set-aside program share recomputation decisions.

Science.gov (United States)

2010-07-01

... appeal: (i) The appellant's name, mailing address, and daytime telephone number; (ii) The title or type... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Appeal process for small... FOREST SYSTEM TIMBER Timber Sale Contracts Contract Administration § 223.118 Appeal process for small...

Genetic variation in the CYP1A1 gene is related to circulating PCB118 levels in a population-based sample

Energy Technology Data Exchange (ETDEWEB)

Lind, Lars [Department of Medical Sciences, Cardiovascular Epidemiology, Uppsala University, Uppsala (Sweden); Penell, Johanna [Department of Medical Sciences, Occupational and Environmental Medicine, Uppsala University, Uppsala (Sweden); Syvänen, Anne-Christine; Axelsson, Tomas [Department of Medical Sciences, Molecular Medicine and Science for Life Laboratory, Uppsala University, Uppsala (Sweden); Ingelsson, Erik [Department of Medical Sciences, Molecular Epidemiology and Science for Life Laboratory, Uppsala University, Uppsala (Sweden); Wellcome Trust Centre for Human Genetics, University of Oxford, Oxford (United Kingdom); Morris, Andrew P.; Lindgren, Cecilia [Wellcome Trust Centre for Human Genetics, University of Oxford, Oxford (United Kingdom); Salihovic, Samira; Bavel, Bert van [MTM Research Centre, School of Science and Technology, Örebro University, Örebro (Sweden); Lind, P. Monica, E-mail: monica.lind@medsci.uu.se [Department of Medical Sciences, Occupational and Environmental Medicine, Uppsala University, Uppsala (Sweden)

2014-08-15

Several of the polychlorinated biphenyls (PCBs), i.e. the dioxin-like PCBs, are known to induce the P450 enzymes CYP1A1, CYP1A2 and CYP1B1 by activating the aryl hydrocarbon receptor (Ah)-receptor. We evaluated if circulating levels of PCBs in a population sample were related to genetic variation in the genes encoding these CYPs. In the population-based Prospective Investigation of the Vasculature in Uppsala Seniors (PIVUS) study (1016 subjects all aged 70), 21 SNPs in the CYP1A1, CYP1A2 and CYP1B1 genes were genotyped. Sixteen PCB congeners were analysed by high-resolution chromatography coupled to high-resolution mass spectrometry (HRGC/ HRMS). Of the investigated relationships between SNPs in the CYP1A1, CYP1A2 and CYP1B1 and six PCBs (congeners 118, 126, 156, 169, 170 and 206) that captures >80% of the variation of all PCBs measured, only the relationship between CYP1A1 rs2470893 was significantly related to PCB118 levels following strict adjustment for multiple testing (p=0.00011). However, there were several additional SNPs in the CYP1A2 and CYP1B1 that showed nominally significant associations with PCB118 levels (p-values in the 0.003–0.05 range). Further, several SNPs in the CYP1B1 gene were related to both PCB156 and PCB206 with p-values in the 0.005–0.05 range. Very few associations with p<0.05 were seen for PCB126, PCB169 or PCB170. Genetic variation in the CYP1A1 was related to circulating PCB118 levels in the general elderly population. Genetic variation in CYP1A2 and CYP1B1 might also be associated with other PCBs. - Highlights: • We studied the relationship between PCBs and the genetic variation in the CYP genes. • Cross sectional data from a cohort of elderly were analysed. • The PCB levels were evaluated versus 21 SNPs in three CYP genes. • PCB 118 was related to variation in the CYP1A1 gene.

Numerical study of the static and pitching RISØ-B1-18 airfoil

DEFF Research Database (Denmark)

Bertagnolio, Franck

2004-01-01

The objective of this report is the better understanding of the physics of the aeroelastic motion of wind turbine blades in order to improve the numerical models used for their design. In this study, the case of the RISØ-B1-18 airfoil which was equippedand measured in an open jet wind tunnel...... that are available both for the static airfoil and in the case of pitching motions. It is shown that the Navier-Stokes simulations can reproduced the maincharacteristic features of the flow. The DES model seems also to be able to reproduce some details of the unsteady aerodynamics. The Navier-Stokes computations can...

SD118-Xanthocillin X (1, a Novel Marine Agent Extracted from Penicillium commune, Induces Autophagy through the Inhibition of the MEK/ERK Pathway

Directory of Open Access Journals (Sweden)

Caiguo Huang

2012-06-01

Full Text Available A compound named SD118-xanthocillin X (1 (C₁₈H₁₂N₂O₂, isolated from Penicillium commune in a deep-sea sediment sample, has been shown to inhibit the growth of several cancer cell lines in vitro. In the present study, we employed a growth inhibition assay and apoptotic analysis to identify the biological effect and detailed mechanism of SD118-xanthocillin X (1 in human hepatocellular carcinoma (HepG2 cells. SD118-xanthocillin X (1 demonstrated a concentration-dependent inhibitory effect on the growth of HepG2 cells and caused slight cellular apoptosis and significantly induced autophagy. Autophagy was detected as early as 12 h by the conversion of microtubule-associated protein 1 light chain 3 (LC3-I to LC3-II, following cleavage and lipid addition to LC3-I. The pharmacological autophagy inhibitor 3-methyladenine largely attenuates the growth inhibition and autophagic effect of SD118-xanthocillin X (1 in HepG2 cells. Our data also indicated that the autophagic effect of SD118-xanthocillin X (1 occurs via the down-regulation of the MEK/ERK signaling pathway and the up-regulated class III PI3K/Beclin 1 signaling pathway.

Cleanup Verification Package for the 118-B-1, 105-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Capron, J.M.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance criteria for the 118-B-1, 105-B Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-B Reactor and P-10 Tritium Separation Project and also received waste from the 105-N Reactor. The burial ground received reactor hardware, process piping and tubing, fuel spacers, glassware, electrical components, tritium process wastes, soft wastes and other miscellaneous debris

An Accurate Redetermination of the $^{118}Sn$ Binding Energy

CERN Document Server

Borzakov, S B; Faikow-Stanczyk, H; Grigoriev, Yu V; Panteleev, T; Pospísil, S; Smotritsky, L M; Telezhnikov, S A

2001-01-01

The energy of well-known strong {gamma}-line from {{^198}Au}, the "gold standard", has been modified in the light of new adjustments in the fundamental constants and the value of 411.80176(12) keV was determined which is 0.29 eV lower than the latest 1999 value. An energy calibration procedure for determining the neutron binding energy, {B_n}, from complicated {(n , gamma)}-spectra has been developed. A mathematically simple minimization function consisting only of terms having as parameters the coefficients of the energy calibration curve (polynomial) is used. A priori information about the relationships among the energies of different peaks on the spectrum is taking into account by a Monte Carlo simulation. The procedure was used in obtaining of {B_n} for {{^118}Sn} and {{^64}Cu}. The {gamma}-ray spectrum from thermal neutron radiative capture by {{^117}Sn} has been measured on the IBR-2 pulsed reactor. {gamma}-rays were detected by a 72 cm^3 HPGe-detector. {B_n} for {{^64}Cu} was obtained from two {gamma}-...

Resonant ionization by laser beams: application to ions sources and to study the nuclear structure of radioactive tellurium isotopes

International Nuclear Information System (INIS)

Sifi, R.

2007-07-01

The radioactive ion beams that are produced through current isotope separators are well separated according to the A mass but not according to the Z parameter. The resonant ionization through laser beams applied to ion sources allows the production of radioactive ion beam in a very selective and efficient way by eliminating the isobaric contamination. The first chapter is dedicated to the resonant ionization by laser beams, we describe the principle, the experimental setting, the lasers used, the ionization schemes and the domain of application. The second chapter deals with the application of resonant ionization to laser ion sources for the production of radioactive ion beams. We present experimental tests performed for getting copper ion beams. Resonant ionization through laser is also used in the spectroscopy experiments performed at the Isolde (isotope separation on-line device) installation in CERN where more than 20 elements are ionized very efficiently. The technique is based on a frequency scanning around the excitation transition of the atoms in order to probe the hyperfine structure. Laser spectroscopy allows the determination of the hyperfine structure as well as the isotopic shift of atoms. In the third chapter the method is applied to the spectroscopy of tellurium atoms. First, we define the 2 parameters on which the extraction is based: charge radius and nuclear moments, then we present several theoretical models that we have used to assess our experimental results. (A.C.)

Consequences of the 118A>G polymorphism in the OPRM1 gene: translation from bench to bedside?

Directory of Open Access Journals (Sweden)

Mura E

2013-05-01

Full Text Available Elisa Mura,1 Stefano Govoni,1 Marco Racchi,1 Valeria Carossa,1 Guglielmina Nadia Ranzani,2 Massimo Allegri,3,4 Ron HN van Schaik5 1Department of Drug Sciences, Centre of Excellence in Applied Biology, University of Pavia, Pavia, Italy; 2Department of Biology and Biotechnology, University of Pavia, Pavia, Italy; 3Pain Therapy Service, Foundation IRCCS San Matteo Hospital, Pavia, Italy; 4Department of Clinical, Surgical Diagnostic and Pediatric Sciences, University of Pavia, Pavia, Italy; 5Department of Clinical Chemistry, Erasmus University Medical Center, Rotterdam, The Netherlands Abstract: The 118A>G single nucleotide polymorphism (SNP in the µ-opioid receptor (OPRM1 gene has been the most described variant in pharmacogenetic studies regarding opioid drugs. Despite evidence for an altered biological function encoded by this variant, this knowledge is not yet utilized clinically. The aim of the present review was to collect and discuss the available information on the 118A>G SNP in the OPRM1 gene, at the molecular level and in its clinical manifestations. In vitro biochemical and molecular assays have shown that the variant receptor has higher binding affinity for ß-endorphins, that it has altered signal transduction cascade, and that it has a lower expression compared with wild-type OPRM1. Studies using animal models for 118A>G have revealed a double effect of the variant receptor, with an apparent gain of function with respect to the response to endogenous opioids but a loss of function with exogenous administered opioid drugs. Although patients with this variant have shown a lower pain threshold and a higher drug consumption in order to achieve the analgesic effect, clinical experiences have demonstrated that patients carrying the variant allele are not affected by the increased opioid consumption in terms of side effects. Keywords: µ-opioid receptor, opioids, pharmacogenetics, pain, analgesia

41 CFR 102-118.275 - What must my agency consider when designing and implementing a prepayment audit program?

Science.gov (United States)

2010-07-01

... MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Prepayment Audits of Transportation... services, your agency should ensure that each TSP bill or employee travel voucher contains enough information for the prepayment audit to determine which contract or rate tender is used and that the type and...

41 CFR 102-118.25 - Does GSA still require my agency to submit its overall transportation policies for approval?

Science.gov (United States)

2010-07-01

... Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT General Introduction... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Does GSA still require...

Electrical properties of tellurium clusters on the void sublattice of an opal crystal the important role played by the Te-SiO$_{2}$ interface

CERN Document Server

Berezovets, V A; Farbshtein, I I; Nizhankovskii, V I

2002-01-01

The temperature dependences of electrical resistivity and of the Hall effect of nanocluster tellurium crystals obtained by filling the voids in a dielectric (opal) matrix with a melt of pure and doped Te were studied. The Hall hole concentration p/sub eff/ was found to increase anomalously (by more than two orders of magnitude) in a sample prepared from pure Te and cooled to helium temperatures. At T = 1.45 K, the hole concentration in this sample was p/sub eff/ = equivalent to 6 * 10/sup 17/ cm/sup -3/. At the same time, the Hall effect in this sample was observed to reverse sign at T equivalent to 200 K from positive for T < 200 K to negative at higher temperatures. This implies a low impurity concentration (N/sub A/ is less than at least 10/sup 15/ cm/sup -3/). A nanocluster crystal of doped Te does not exhibit this anomaly; here, we have p/sub eff/ equivalent to 6 * 10/sup 17/ cm/sup -3/ throughout the temperature region covered, as in the original Te. These features are assigned to the formation of a ...

Organotellurium ligands – designing and complexation reactions

Indian Academy of Sciences (India)

Unknown

membered rings it is negative and ~30 ppm only. Keywords. Organotellurium ligands; hybrid telluroether; platinum metal complexes; tellurium-125 NMR. 1. Introduction. Tellurium is the noblest metalloid which may act as a Lewis acid as well as Lewis base. The ligand chemistry of tellurium, which acts as a 'soft' donor, was ...

41 CFR 102-118.150 - What are the major mandatory terms and conditions governing the use of passenger transportation...

Science.gov (United States)

2010-07-01

...) Interest shall accrue from the voucher payment date on overcharges made hereunder and shall be paid at the... (Continued) FEDERAL MANAGEMENT REGULATION TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Ordering and... responsible for charges exceeding those applicable to the type, class, or character authorized in...

41 CFR 102-118.195 - What documents must a transportation service provider (TSP) send to receive payment for a...

Science.gov (United States)

2010-07-01

... transportation service provider (TSP) send to receive payment for a transportation billing? 102-118.195 Section... must a transportation service provider (TSP) send to receive payment for a transportation billing? For... Government Billing Documents Terms and Conditions Governing Acceptance and Use of A Government Bill of Lading...

41 CFR 102-118.165 - What must my agency do if it finds an error on a TSP bill?

Science.gov (United States)

2010-07-01

..., payment voucher number, complete tender or tariff authority, the applicable rate authority and the... TRANSPORTATION 118-TRANSPORTATION PAYMENT AND AUDIT Ordering and Paying for Transportation and Transportation... writing within 7 days of receipt of the bill, as required by the Prompt Payment Act (31 U.S.C. 3901, et...

RhCd{sub 9+δ} (-1.18 ≤δ≤0.29) a γ-brass related cubic giant cell structure

Energy Technology Data Exchange (ETDEWEB)

Jana, Partha Pratim [Indian Institute of Technology, Kharagpur (India). Dept. of Chemistry

2017-09-01

The compound RhCd{sub 9+δ} (-1.18 ≤δ≤0.29) has been synthesized and the average structure has been analyzed by single crystal X-ray diffraction. The average structure crystallizes in the face centered cubic space group F43m (216) and contains ∝405 atoms/unit cell. It represents a (2a{sub γ}){sup 3}-superstructure of cubic γ-brass and is isostructural to Rh{sub 7-x}Mg{sub 44+x}. The comparison between the structures of RhCd{sub 9+δ} and Rh{sub 7-x}Mg{sub 44+x} has been presented using a layer description. The structure of the title phase has also been described by a ''cluster'' concept. The electronic structure of RhCd{sub 9+δ} (-1.18 ≤δ≤0.29) shows that the phase is stabilized by a Hume-Rothery mechanism.

The cross sections of fusion-evaporation reactions: the most promising route to superheavy elements beyond Z=118

Directory of Open Access Journals (Sweden)

Jadambaa Khuyagbaatar

2017-01-01

Full Text Available The synthesis of superheavy elements beyond oganesson (Og, which has atomic number Z = 118, is currently one of the main topics in nuclear physics. An absence of sufficient amounts of target material with atomic numbers heavier than californium (Z = 98 forces the use of projectiles heavier than 48Ca (Z = 20, which has been successfully used for the discoveries of elements with Z = 114 - 118 in complete fusion reactions. Experimental cross sections of 48Ca with actinide targets behave very differently to “cold” and “hot” fusion-evaporation reactions, where doubly-magic lead and deformed actinides are used as targets, respectively. The known cross sections of these reactions have been analysed compared to calculated fission barriers. It has been suggested that observed discrepancies between the cross sections of 48Ca-induced and other fusionevaporation reactions originate from the shell structure of the compound nucleus, which lies in the island of the stability. Besides scarcely known data on other reactions involving heavier projectiles, the most promising projectile for the synthesis of the elements beyond Og seems to be 50Ti. However, detailed studies of 50Ti, 54Cr, 58Fe and 64Ni-induced reactions are necessary to be performed in order to fully understand the complexities of superheavy element formation.

The cross sections of fusion-evaporation reactions: the most promising route to superheavy elements beyond Z=118

Science.gov (United States)

Jadambaa, Khuyagbaatar

2017-11-01

The synthesis of superheavy elements beyond oganesson (Og), which has atomic number Z = 118, is currently one of the main topics in nuclear physics. An absence of sufficient amounts of target material with atomic numbers heavier than californium (Z = 98) forces the use of projectiles heavier than 48Ca (Z = 20), which has been successfully used for the discoveries of elements with Z = 114 - 118 in complete fusion reactions. Experimental cross sections of 48Ca with actinide targets behave very differently to "cold" and "hot" fusion-evaporation reactions, where doubly-magic lead and deformed actinides are used as targets, respectively. The known cross sections of these reactions have been analysed compared to calculated fission barriers. It has been suggested that observed discrepancies between the cross sections of 48Ca-induced and other fusionevaporation reactions originate from the shell structure of the compound nucleus, which lies in the island of the stability. Besides scarcely known data on other reactions involving heavier projectiles, the most promising projectile for the synthesis of the elements beyond Og seems to be 50Ti. However, detailed studies of 50Ti, 54Cr, 58Fe and 64Ni-induced reactions are necessary to be performed in order to fully understand the complexities of superheavy element formation.

Geophysical investigation of the 120-KE-3 and 118-K-2 sites, 100-KR-2 operable unit

International Nuclear Information System (INIS)

Bergstrom, K.A.; Mitchell, T.H.; Bolin, B.J.

1995-04-01

Geophysical investigations using ground-penetrating radar (GPR) and electromagnetic induction (EMI) were conducted at two waste sites, 120-KE-3 and 118-K-2, in the 100-K Area (Figure 1). Both of the sites are located within Operable Unit 100-KR-2. The 120-KE-3 waste site (Figure 2), also known as the 183-Filter Water Facility Trench and 100-KE-3, received sulfuric acid sludge from sulfuric acid storage tanks that were contaminated with 700 kg of mercury. The trench is documented as 3 ft wide by 3 ft deep by 40 ft long. However, part or all of the trench was excavated when an outside contractor attempted to recover the mercury (Carpenter and Cote 1994). Therefore, the actual size of the ''disturbed area'' from the trench and subsequent excavation is unknown. The objective of the geophysical investigation was to locate the original or reworked trench. The 118- K-2 site (Figure 3) was reportedly used to dispose radioactive sludge from the 116-KE-4 and 116-KW-3 retention basins. The size of the ''trench'' is unknown and documentation shows it in two different locations. No other information si available on the site. The objective of the investigation was to locate the trench

Effect of composition on the degree of anisotropy of thermal expansion and electric resistance of cermet specimens of GeTe

International Nuclear Information System (INIS)

Barbakadze, K.G.; Vekua, T.S.; Ioseliani, M.I.; Kvitsiniya, K.M.

1988-01-01

A study was made on α temperature coefficient of thermal expansion and ρ specific electric resistance of cermet germanium telluride for alloys close to stoichiometric composition. It is shown that anisotropy of thermal expansion of cermet germanium telluride depends sufficiently on its composition. This dependence is clearly pronounced if tellurium content in alloys equals 50.4-51.2 at.%. The maximal anisotropy is observed in the alloy containing 50.8 at.% of tellurium. The temperature of extreme value of temperature coefficient of linear expansion decreases from 440 down to 373 deg.C for alloys with 49-50.8 at.% of tellurium, and grows from 373 up to 405 deg.C if tellurium content equals 50.8-52 at.%

Bioavailability of 2,3',4,4',5-pentachlorobiphenyl (PCB118) and 2,2',5,5'-tetrachlorobiphenyl (PCB52) from soils using a rat model and a physiologically based extraction test

International Nuclear Information System (INIS)

Pu Xinzhu; Lee, Linda S.; Galinsky, Raymond E.; Carlson, Gary P.

2006-01-01

The bioavailability of coplanar 2,3',4,4',5-pentachlorobiphenyl (PCB118) and nonplanar 2,2',5,5'-tetrachlorobiphenyl (PCB52) from soils representing a range in organic carbon (OC), clay content and pH were investigated using an in vivo rat model and an in vitro physiologically based extraction test (PBET) to assess the role of soil and chemical properties on bioavailabilty. Affinity to soil and persistence of PCBs have been shown to increase with increasing soil organic carbon (OC) content, PCB chlorination, and PCB coplanarity. In the in vivo tests for both PCB118 and PCB52, the AUCs following iv injection were significantly higher than the AUCs for all soil groups, indicating that the soil matrix can reduce the absolute bioavailability of PCB118 and PCB52. However, no significant differences were detected between soils of different properties. In the in vitro PBET, significant differences in the mobilization of PCB118 and PCB52 were observed among soils, and PCBs had the least mobilization from the soil with the highest OC content consistent with hydrophobic partitioning theory. Also, significantly less PCB118 was mobilized relative to PCB52 in the PBET assay, showing the potential impact of spatial orientation and chlorine content on bioavailability. No correlation between the in vitro PBET and the in vivo rat model was observed for the PCBs. Although the in vitro PBET and related assays may serve as an indicator of bioavailability, it is likely to underestimate what can be released from a soil in an in vivo assay

Desiring the death-of-the-death. Michelangelo (madrigal n.118), Shakespeare (son. 146), Donne (sacred son. X)

OpenAIRE

Ida Campeggiani

2013-01-01

Michelangelo wrote two versions of the madrigal n. 118; the second one transforms the meaning of the first from the profane to the sacred, with minor variants. Both are included in the archive of texts known as ‘canzoniere’. An analysis of the two shows Michelangelo’s intention to introduce private drives in his work, taking care, though, of creating a framework within which to absorb those subversive aspects the prevailing morality would have rejected. Buonarroti uses the topos of the lover’...

Cleanup Verification Package for the 118-H-6:2, 105-H Reactor Ancillary Support Areas, Below-Grade Structures, and Underlying Soils; the 118-H-6:3, 105-H Reactor Fuel Storage Basin and Underlying Soils; the 118-H-6:6 Fuel Storage Basin Deep Zone Side Slope Soils; the 100-H-9, 100-H-10, and 100-H-13 French Drains; the 100-H-11 and 100-H-12 Expansion Box French Drains; and the 100-H-14 and 100-H-31 Surface Contamination Zones

International Nuclear Information System (INIS)

Appel, M.J.

2006-01-01

This cleanup verification package documents completion of removal actions for the 105-H Reactor Ancillary Support Areas, Below-Grade Structures, and Underlying Soils (subsite 118-H-6:2); 105-H Reactor Fuel Storage Basin and Underlying Soils (118-H-6:3); and Fuel Storage Basin Deep Zone Side Slope Soils. This CVP also documents remedial actions for the following seven additional waste sties: French Drain C (100-H-9), French Drain D (100-H-10), Expansion Box French Drain E (100-H-11), Expansion Box French Drain F (100-H-12), French Drain G (100-H-13), Surface Contamination Zone H (100-H-14), and the Polychlorinated Biphenyl Surface Contamination Zone (100-H-31)

118 SNPs of folate-related genes and risks of spina bifida and conotruncal heart defects

Directory of Open Access Journals (Sweden)

Shaw Gary M

2009-06-01

Full Text Available Abstract Background Folic acid taken in early pregnancy reduces risks for delivering offspring with several congenital anomalies. The mechanism by which folic acid reduces risk is unknown. Investigations into genetic variation that influences transport and metabolism of folate will help fill this data gap. We focused on 118 SNPs involved in folate transport and metabolism. Methods Using data from a California population-based registry, we investigated whether risks of spina bifida or conotruncal heart defects were influenced by 118 single nucleotide polymorphisms (SNPs associated with the complex folate pathway. This case-control study included 259 infants with spina bifida and a random sample of 359 nonmalformed control infants born during 1983–86 or 1994–95. It also included 214 infants with conotruncal heart defects born during 1983–86. Infant genotyping was performed blinded to case or control status using a designed SNPlex assay. We examined single SNP effects for each of the 118 SNPs, as well as haplotypes, for each of the two outcomes. Results Few odds ratios (ORs revealed sizable departures from 1.0. With respect to spina bifida, we observed ORs with 95% confidence intervals that did not include 1.0 for the following SNPs (heterozygous or homozygous relative to the reference genotype: BHMT (rs3733890 OR = 1.8 (1.1–3.1, CBS (rs2851391 OR = 2.0 (1.2–3.1; CBS (rs234713 OR = 2.9 (1.3–6.7; MTHFD1 (rs2236224 OR = 1.7 (1.1–2.7; MTHFD1 (hcv11462908 OR = 0.2 (0–0.9; MTHFD2 (rs702465 OR = 0.6 (0.4–0.9; MTHFD2 (rs7571842 OR = 0.6 (0.4–0.9; MTHFR (rs1801133 OR = 2.0 (1.2–3.1; MTRR (rs162036 OR = 3.0 (1.5–5.9; MTRR (rs10380 OR = 3.4 (1.6–7.1; MTRR (rs1801394 OR = 0.7 (0.5–0.9; MTRR (rs9332 OR = 2.7 (1.3–5.3; TYMS (rs2847149 OR = 2.2 (1.4–3.5; TYMS (rs1001761 OR = 2.4 (1.5–3.8; and TYMS (rs502396 OR = 2.1 (1.3–3.3. However, multiple SNPs observed for a given gene showed evidence of linkage disequilibrium indicating

Tellurium sulfates from reactions in oleum and sulfur trioxide: syntheses and crystal structures of TeO(SO{sub 4}), Te{sub 4}O{sub 3}(SO{sub 4}){sub 5}, and Te(S{sub 2}O{sub 7}){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Logemann, Christian; Bruns, Joern; Schindler, Lisa Verena; Zimmermann, Vanessa; Wickleder, Mathias S. [Carl von Ossietzky University of Oldenburg, Institute of Chemistry (Germany)

2015-04-15

The reaction of K{sub 2}TeO{sub 4} with fuming sulfuric acid (65 % SO{sub 3}) in sealed glass ampoules at 250 C led to colorless single crystals of TeO(SO{sub 4}) [triclinic, P anti 1, Z = 8, a = 819.89(3) pm, b = 836.95(4) pm, c = 1179.12(5) pm, α = 82.820(2) , β = 70.645(2) , γ = 81.897(2) , V = 753.11(6) x 10{sup 6} pm{sup 3}]. A horseshoe type [Te{sub 4}O{sub 3}] fragment is the basic motif in the layer structure of the compound. The [Te{sub 4}O{sub 3}] moieties are linked to infinite chains by further oxide ions. Monomeric [Te{sub 4}O{sub 3}] horseshoes are found in the crystal structure of Te{sub 4}O{sub 3}(SO{sub 4}){sub 5} [trigonal, P3{sub 2}21, Z = 3, a = 859.05(2) pm, c = 2230.66(7) pm, V = 1425.61(6) x 10{sup 6} pm{sup 3}], which was obtained from TeO{sub 2} and fuming sulfuric acid (65 % SO{sub 3}) at 200 C as colorless single crystals. By switching to neat SO{sub 3} as reaction medium colorless crystals of Te(S{sub 2}O{sub 7}){sub 2} [P2{sub 1}/n, Z = 4, a = 1065.25(3) pm, b = 818.50(2) pm, c = 1206.27(3) pm, β = 102.097(1) , V = 1028.40(5) x 10{sup 6} pm{sup 3}] form when ortho-telluric acid, H{sub 6}TeO{sub 6}, is used as the tellurium source. The compound was reported previously, however, obviously with a wrong crystallographic description. In the crystal structure the tellurium atoms are coordinated by two chelating disulfate ions. Further Te-O contacts link the [Te(S{sub 2}O{sub 7}){sub 2}] units to an extended network. (Copyright copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Studies on cellular accumulation of satraplatin and its major metabolite JM118 and their interactions with glutathione

Czech Academy of Sciences Publication Activity Database

Kostrhunová, Hana; Kašpárková, Jana; Gibson, D.; Brabec, Viktor

2010-01-01

Roč. 7, č. 6 (2010), s. 2093-2102 ISSN 1543-8384 R&D Projects: GA MŠk(CZ) ME08017; GA MŠk(CZ) ME10066; GA MŠk(CZ) OC08003; GA AV ČR(CZ) IAA400040803; GA ČR(CZ) GAP301/10/0598 Grant - others:GA MŠk(CZ) LC06030; GA AV ČR(CZ) KAN200200651 Program:LC; KA Institutional research plan: CEZ:AV0Z50040507; CEZ:AV0Z50040702 Keywords : JM118 * cellular accumulation * glutathione Subject RIV: BO - Biophysics Impact factor: 5.400, year: 2010

Thermodynamics of post-growth annealing of cadmium zinc telluride nuclear radiation detectors

Science.gov (United States)

Adams, Aaron Lee

Nuclear Radiation Detectors are used for detecting, tracking, and identifying radioactive materials which emit high-energy gamma and X-rays. The use of Cadmium Zinc Telluride (CdZnTe) detectors is particularly attractive because of the detector's ability to operate at room temperature and measure the energy spectra of gamma-ray sources with a high resolution, typically less than 1% at 662 keV. While CdZnTe detectors are acceptable imperfections in the crystals limit their full market potential. One of the major imperfections are Tellurium inclusions generated during the crystal growth process by the retrograde solubility of Tellurium and Tellurium-rich melt trapped at the growth interface. Tellurium inclusions trap charge carriers generated by gamma and X-ray photons and thus reduce the portion of generated charge carriers that reach the electrodes for collection and conversion into a readable signal which is representative of the ionizing radiation's energy and intensity. One approach in resolving this problem is post-growth annealing which has the potential of removing the Tellurium inclusions and associated impurities. The goal of this project is to use experimental techniques to study the thermodynamics of Tellurium inclusion migration in post-growth annealing of CdZnTe nuclear detectors with the temperature gradient zone migration (TGZM) technique. Systematic experiments will be carried out to provide adequate thermodynamic data that will inform the engineering community of the optimum annealing parameters. Additionally, multivariable correlations that involve the Tellurium diffusion coefficient, annealing parameters, and CdZnTe properties will be analyzed. The experimental approach will involve systematic annealing experiments (in Cd vapor overpressure) on different sizes of CdZnTe crystals at varying temperature gradients ranging from 0 to 60°C/mm (used to migrate the Tellurium inclusion to one side of the crystal), and at annealing temperatures ranging

Local order in molten Sesub(1-x)Tesub(x)

International Nuclear Information System (INIS)

Bellissent, R.; Tourand, G.

1980-04-01

In this paper a study of the short range order and of the coordination number in liquid Selenium-Tellurium systems is presented. The first part deals with neutron diffraction measurements of the structure factors of liquid Sesub(1-x)Tesub(x) in the whole concentration range, at 475 C, performed at EL3 reactor in Saclay using a 640 cell multidetector. From these data the radial distribution functions have been calculated. In a second part a structural model based on random chains for Selenium and on a quasicrystalline behavior of Tellurium is presented. For Se-rich melts it is assumed that Tellurium enters the Selenium chains by substitution. In the Te-rich range it is assumed that the local order is represented by substituted SeTe chains in a Tellurium matrix. This model provides with a good representation of the various structure factors. Moreover the coordination number for each concentration in the model has been calculated and the results are consistent with the experimental data. The 2 fold coordination of Se and the 3 valency of Te in the liquid state are emphasized and they can be associated with the metallisation of liquid Tellurium whereas Selenium remains a semiconductor

Contact-resonance atomic force microscopy for nanoscale elastic property measurements: Spectroscopy and imaging

International Nuclear Information System (INIS)

Stan, G.; Krylyuk, S.; Davydov, A.V.; Vaudin, M.D.; Bendersky, L.A.; Cook, R.F.

2009-01-01

Quantitative measurements of the elastic modulus of nanosize systems and nanostructured materials are provided with great accuracy and precision by contact-resonance atomic force microscopy (CR-AFM). As an example of measuring the elastic modulus of nanosize entities, we used the CR-AFM technique to measure the out-of-plane indentation modulus of tellurium nanowires. A size-dependence of the indentation modulus was observed for the investigated tellurium nanowires with diameters in the range 20-150 nm. Over this diameter range, the elastic modulus of the outer layers of the tellurium nanowires experienced significant enhancement due to a pronounced surface stiffening effect. Quantitative estimations for the elastic moduli of the outer and inner parts of tellurium nanowires of reduced diameter are made with a core-shell structure model. Besides localized elastic modulus measurements, we have also developed a unique CR-AFM imaging capability to map the elastic modulus over a micrometer-scale area. We used this CR-AFM capability to construct indentation modulus maps at the junction between two adjacent facets of a tellurium microcrystal. The clear contrast observed in the elastic moduli of the two facets indicates the different surface crystallography of these facets.

Hydrate research activities that both support and derive from the monitoring station/sea-floor Observatory, Mississippi Canyon 118, northern Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Lutken, Carol [Univ. of Mississippi, Oxford, MS (United States). Center for Marine Resources and Environmental Technology (CMRET)

2013-07-31

A permanent observatory has been installed on the seafloor at Federal Lease Block, Mississippi Canyon 118 (MC118), northern Gulf of Mexico. Researched and designed by the Gulf of Mexico Hydrates Research Consortium (GOM-HRC) with the geological, geophysical, geochemical and biological characterization of in situ gas hydrates systems as the research goal, the site has been designated by the Bureau of Ocean Energy Management as a permanent Research Reserve where studies of hydrates and related ocean systems may take place continuously and cooperatively into the foreseeable future. The predominant seafloor feature at MC118 is a carbonate-hydrate complex, officially named Woolsey Mound for the founder of both the GOM-HRC and the concept of the permanent seafloor hydrates research facility, the late James Robert “Bob” Woolsey. As primary investigator of the overall project until his death in mid-2008, Woolsey provided key scientific input and served as chief administrator for the Monitoring Station/ Seafloor Observatory (MS-SFO). This final technical report presents highlights of research and accomplishments to date. Although not all projects reached the status originally envisioned, they are all either complete or positioned for completion at the earliest opportunity. All Department of Energy funds have been exhausted in this effort but, in addition, leveraged to great advantage with additional federal input to the project and matched efforts and resources. This report contains final reports on all subcontracts issued by the University of Mississippi, Administrators of the project, Hydrate research activities that both support and derive from the monitoring station/sea-floor Observatory, Mississippi Canyon 118, northern Gulf of Mexico, as well as status reports on the major components of the project. All subcontractors have fulfilled their primary obligations. Without continued funds designated for further project development, the Monitoring Station

β-Telluroacroleins and β-tellurovinyl ketones: synthesis, reactions and structure

International Nuclear Information System (INIS)

Sadekov, I.D.

2002-01-01

Data on synthesis, reactivity, spectral characteristics and structure of new telluroorganic synthons, i.e. β-tellurovinylcarbonyl compounds, were generalized and systematized. Synthesis and reactions of β-telluroacroleins and similar cations were considered individually for each type of β-tellurovinylcarbonyl compounds. Special attention was paid to the use of the compounds for preparing tellurium-containing heterocycles. Reactions characteristics of carbonyl groups and tellurium-containing substituents, as well as transformation, as a result of which β-tellurovinylcarbonyl compounds and products of their reactions form tellurium-containing heterocycles, were discussed [ru

Pupil Nondiscrimination Guidelines. Implementing S.118.13 of the Wisconsin Statutes and PI 9 of the Wisconsin Administrative Code. Bullein No. 8327.

Science.gov (United States)

Wisconsin State Dept. of Public Instruction, Madison.

The new S. 118.13, Wisconsin Statutes, bans pupil discrimination in any curricular, extracurricular, pupil services, recreational, or other program or activity in the State of Wisconsin on the basis of sex; race; national origin; ancestry; creed; pregnancy; marital or parental status; sexual orientation; or physical, mental, emotional, or learning…

Certification of butyltins and phenyltins in marine sediment certified reference material by species-specific isotope-dilution mass spectrometric analysis using synthesized {sup 118}Sn-enriched organotin compounds

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Kazumi; Takatsu, Akiko; Watanabe, Takuro; Aoyagi, Yoshie; Yarita, Takashi; Okamoto, Kensaku; Chiba, Koichi [National Institute of Advanced Industrial Science and Technology (AIST), Environmental Standard Section, National Metrology Institute of Japan (NMIJ), Tsukuba, Ibaraki (Japan)

2007-04-15

A new marine sediment certified reference material, NMIJ CRM 7306-a, for butyltin and phenyltin analysis has been prepared and certified by the National Metrological Institute of Japan at the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST). Candidate sediment material was collected at a bay near industrial activity in Japan. After air-drying, sieving, and mixing the material was sterilized with {gamma}-ray irradiation. The material was re-mixed and packaged into 250 glass bottles (15 g each) and these were stored in a freezer at -30 C. Certification was performed by use of three different types of species-specific isotope-dilution mass spectrometry (SSID-MS) - SSID-GC-ICP-MS, SSID-GC-MS, and SSID-LC-ICP-MS, with {sup 118}Sn-enriched organotin compounds synthesized from {sup 118}Sn-enriched metal used as a spike. The {sup 118}Sn-enriched mono-butyltin (MBT), dibutyltin (DBT), and tributyltin (TBT) were synthesized as a mixture whereas the {sup 118}Sn-enriched di-phenyltin (DPhT) and triphenyltin (TPhT) were synthesized individually. Four different extraction methods, mechanical shaking, ultrasonic, microwave-assisted, and pressurized liquid extraction, were adopted to avoid possible analytical bias caused by non-quantitative extraction and degradation or inter-conversion of analytes in sample preparations. Tropolone was used as chelating agent in all the extraction methods. Certified values are given for TBT 44{+-}3 {mu}g kg{sup -1} as Sn, DBT 51 {+-} 2 {mu}g kg{sup -1} as Sn, MBT 67 {+-} 3 {mu}g kg{sup -1} as Sn, TPhT 6.9 {+-} 1.2 {mu}g kg{sup -1} as Sn, and DPhT 3.4 {+-} 1.2 {mu}g kg{sup -1} as Sn. These levels are lower than in other sediment CRMs currently available for analysis of organotin compounds. (orig.)

Numerical study of the static and pitching RISOe-B1-18 airfoil[STALL

Energy Technology Data Exchange (ETDEWEB)

Bertagnolio, F.

2004-01-01

The objective of this report is the better understanding of the physics of the aeroelastic motion of wind turbine blades in order to improve the numerical models used for their design. In this study, the case of the RISOe-B1-18 airfoil which was equipped and measured in an open jet wind tunnel is studied. Two and three dimensional Navier-Stokes calculations using the k-w SST and Detached Eddy Simulation turbulence models are conducted. An engineering semi-empirical dynamic stall model is also used for performing calculations. Computational results are compared to the experimental results that are available both for the static airfoil and in the case of pitching motions. It is shown that the Navier-Stokes simulations can reproduced the main characteristic features of the flow. The DES model seems also to be able to reproduce some details of the unsteady aerodynamics. The Navier-Stokes computations can then be used to improve the performance of the engineering model. (au)

New studies on mustard gold from the Dongping Mines, Hebei Province, China: The tellurian, plumbian, manganoan and mixed varieties

DEFF Research Database (Denmark)

Li, Jiuling; Makovicky, Emil

2001-01-01

geologi, Dongping gold tellurite deposit, mustard gold, calaverite, Fe-Pb-Te minerals, alteration, tellurium, filling in micro-porous, composite varieties, particles of gold......geologi, Dongping gold tellurite deposit, mustard gold, calaverite, Fe-Pb-Te minerals, alteration, tellurium, filling in micro-porous, composite varieties, particles of gold...

Absolute vibrational excitation cross sections for 1-18 eV electron scattering from condensed dimethyl phosphate (DMP)

Science.gov (United States)

Lemelin, V.; Bass, A. D.; Wagner, J. R.; Sanche, L.

2017-12-01

Absolute cross sections (CSs) for vibrational excitation by 1-18 eV electrons incident on condensed dimethyl phosphate (DMP) were measured with a high-resolution electron energy loss (EEL) spectrometer. Absolute CSs were extracted from EEL spectra of DMP condensed on multilayer film of Ar held at about 20 K under ultra-high vacuum (˜1 × 10-11 Torr). Structures observed in the energy dependence of the CSs around 2, 4, 7, and 12 eV were compared with previous results of gas- and solid-phase experiments and with theoretical studies on dimethyl phosphate and related molecules. These structures were attributed to the formation of shape resonances.

Job Strain and Health-Related Lifestyle : Findings From an Individual-Participant Meta-Analysis of 118 000 Working Adults.

OpenAIRE

Heikkilä, Katriina; Fransson, Eleonor I; Nyberg, Solja T; Zins, Marie; Westerlund, Hugo; Westerholm, Peter; Virtanen, Marianna; Vahtera, Jussi; Suominen, Sakari; Steptoe, Andrew; Salo, Paula; Pentti, Jaana; Oksanen, Tuula; Nordin, Maria; Marmot, Michael G

2013-01-01

Objectives. We examined the associations of job strain, an indicator of work-related stress, with overall unhealthy and healthy lifestyles. Methods. We conducted a meta-analysis of individual-level data from 11 European studies (cross-sectional data: n = 118 701; longitudinal data: n = 43 971). We analyzed job strain as a set of binary (job strain vs no job strain) and categorical (high job strain, active job, passive job, and low job strain) variables. Factors used to define healthy and unhe...

Human Mu Opioid Receptor (OPRM1A118G) polymorphism is associated with brain mu- opioid receptor binding potential in smokers

International Nuclear Information System (INIS)

Ray, R.; Logan, J.; Ruparel, K.; Newberg, A.; Wileyto, E.P.; Loughead, J.W.; Divgi, C.; Blendy, J.A.; Logan, J.; Zubieta, J.-K.; Lerman, C.

2011-01-01

Evidence points to the endogenous opioid system, and the mu-opioid receptor (MOR) in particular, in mediating the rewarding effects of drugs of abuse, including nicotine. A single nucleotide polymorphism (SNP) in the human MOR gene (OPRM1 A118G) has been shown to alter receptor protein level in preclinical models and smoking behavior in humans. To clarify the underlying mechanisms for these associations, we conducted an in vivo investigation of the effects of OPRM1 A118G genotype on MOR binding potential (BP ND or receptor availability). Twenty-two smokers prescreened for genotype (12 A/A, 10 */G) completed two [ 11 C] carfentanil positron emission tomography (PET) imaging sessions following overnight abstinence and exposure to a nicotine-containing cigarette and a denicotinized cigarette. Independent of session, smokers homozygous for the wild-type OPRM1 A allele exhibited significantly higher levels of MOR BP ND than smokers carrying the G allele in bilateral amygdala, left thalamus, and left anterior cingulate cortex. Among G allele carriers, the extent of subjective reward difference (denicotinized versus nicotine cigarette) was associated significantly with MOR BP ND difference in right amygdala, caudate, anterior cingulate cortex, and thalamus. Future translational investigations can elucidate the role of MORs in nicotine addiction, which may lead to development of novel therapeutics.

Analysis of Central Events in the Interactions of Relativistic Heavy Ions with Emulsion Nuclei at 118.4 GeV

International Nuclear Information System (INIS)

EL-Falaky, E.

2007-01-01

Data on the multiplicity of the secondary produced particles in the central events from the interactions of 32S with AgBr nuclei at 118.4 GeV. A different selection criteria of the central collision in heavy ion interactions was investigated. The multiplicity distributions of the different produced shower particles (mainly pions) in the central events for each criteria was studied. The multiplicity distributions of the target fragments emitted in the central events was fitted by a Gaussian distribution. The target analysis of the experimental data shows agreement with the limiting fragmentation hypothesis

The Secret Life of the Periodic Table - Unlocking the mysteries of all 118 elements

International Nuclear Information System (INIS)

Still, Ben; Davis, Jon; Depovere, Paul

2017-01-01

Every element has character, be it volatile, aloof, gregarious or enigmatic. They also have incredible stories of how they came to be, how they were discovered and how their qualities have been harnessed to make everything we have in the world. This book gives a fascinating insight into the discovery and use of all 118 elements. It uncovers incredible stories of how Mendeleev's table was formulated and the individual elements found, as well as explaining the fundamentals of atomic science and each element's place in the table and our universe. Each element description includes a fact box showing atomic number, atomic weight, radius, melting point, boiling point, density, and the year of its discovery and by whom. There are many side-bars, boxes and extended captions covering topics of interest and also fascinating trivia about the elements. This book is the French translation of 'The Secret Life of the Periodic Table' published by Firefly Books (Canada, Sep 2016)

X-ray diffraction analysis of a human tRNAGly acceptor-stem microhelix isoacceptor at 1.18 Å resolution

International Nuclear Information System (INIS)

Eichert, André; Perbandt, Markus; Schreiber, Angela; Fürste, Jens P.; Betzel, Christian; Erdmann, Volker A.; Förster, Charlotte

2008-01-01

The tRNA Gly acceptor-stem microhelix isoacceptor from human cytoplasm was crystallized and X-ray diffraction analysis revealed diffraction to 1.18 Å resolution. The sequence of the microhelix was derived from the gene sequence with tRNA Database ID DG9990. Interest has been focused on comparative X-ray structure analyses of different tRNA Gly acceptor-stem helices. tRNA Gly /glycyl-tRNA synthetase belongs to the so-called class II system, in which the tRNA identity elements consist of simple and unique determinants that are located in the tRNA acceptor stem and the discriminator base. Comparative structure investigations of tRNA Gly microhelices provide insight into the role of tRNA identity elements. Predominant differences in the structures of glycyl-tRNA synthetases and in the tRNA identity elements between prokaryotes and eukaryotes point to divergence during the evolutionary process. Here, the crystallization and high-resolution X-ray diffraction analysis of a human tRNA Gly acceptor-stem microhelix with sequence 5′-G 1 C 2 A 3 U 4 U 5 G 6 G 7 -3′, 5′-C 66 C 67 A 68 A 69 U 70 G 71 C 72 -3′ is reported. The crystals belonged to the monoclinic space group C2, with unit-cell parameters a = 37.32, b = 37.61, c = 30.47 Å, β = 112.60° and one molecule per asymmetric unit. A data set was collected using synchrotron radiation and data were processed within the resolution range 50.0–1.18 Å. The structure was solved by molecular replacement

Reactions of newly formed fission products in the gas phase

International Nuclear Information System (INIS)

Strickert, R.G.

1976-01-01

A dynamic gas-flow system was constructed which stopped fission products in the gas phase and rapidly separated (in less than 2 sec) volatile compounds from non-volatile ones. The filter assembly designed and used was shown to stop essentially all non-volatile fission products. Between 5 percent and 20 percent of tellurium fission-product isotopes reacted with several hydrocarbon gases to form volatile compounds, which passed through the filter. With carbon monoxide gas, volatile tellurium compound(s) (probably TeCO) were also formed with similar efficiencies. The upper limits for the yields of volatile compounds formed between CO and tin and antimony fission products were shown to be less than 0.3 percent, so tellurium nuclides, not their precursors, reacted with CO. It was found that CO reacted preferentially with independently produced tellurium atoms; the reaction efficiency of beta-produced atoms was only 27 +- 3 percent of that of the independently formed atoms. The selectivity, which was independent of the over-all reaction efficiency, was shown to be due to reaction of independently formed atoms in the gas phase. The gas phase reactions are believed to occur mainly at thermal energies because of the independence of the yield upon argon moderator mole-fraction (up to 80 percent). It was shown in some experiments that about one-half of the TeCO decomposed in passing through a filter and that an appreciable fraction (approximately 20 percent) of the tellurium atoms deposited on the filter reacted agin with CO. Other tellurium atoms on the filter surface (those formed by beta decay and those formed independently but not reacting in the gas phase) also reacted with CO, but probably somewhat less efficiently than atoms formed by TeCO decomposition. No evidence was found for formation of TeCO as a direct result of beta-decay

Iodine-131 production by a dry method using reactor-irradiated elementary tellurium. Part 1 - Conditions for obtaining iodine emanation and its capture. Part 2 - comparative study of preparation conditions using Pyrex, stainless steel and alumina equipment. Part 3 - production on a semi-industrial scale; Production de l'iode 131 par voie seche a partir de tellure elementaire irradie a la pile. 1ere partie - Etudes des conditions pour obtenir l'emanation de l'iode et le capter. 2eme partie - Etude comparee des conditions pour effectuer cette preparation avec des appareils en Pyrex, en acier inoxydable et en alumine. 3eme partie - production a l'echelle semi-industrielle

Energy Technology Data Exchange (ETDEWEB)

Bardy, A; Beydon, J; Murthy, T S; Doyen, J B; Lefrancois, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-04-15

A previous report has described how iodine 131 can be prepared from elementary tellurium by a dry method which consists in treating irradiated tellurium at 400 degrees in argon. The possibility of carrying out this treatment in a stainless steel or alumina apparatus has been considered. The behavior of gaseous iodine 131 towards these materials has thus been studied. If the adsorption of iodine on stainless steel is superficial desorption is rapid at 250 degrees in oxygen or 400 degrees in argon. If the adsorption is chemical in nature it becomes necessary to heat to higher temperatures. Adsorption of iodine on alumina is very weak and the iodine can be desorbed rapidly. With these materials tests have been carried out on 300 gms of tellurium containing 41 curies of iodine 131; the yields were very satisfactory ( 98 per cent). (author) [French] La methode de preparation de l iode 131 par voie seche a partir de tellure elementaire decrite dans un precedent rapport consiste a traiter le tellure irradie a 400 degres sous argon. Nous avons examine la possibilite d effectuer ce traitement dans un appareil en acier inoxidable ou en alumine. Le comportement de l iode 131 gazeux vis a vis de ces materiaux a donc ete etudie. Si l adsorption de l iode sur l acier inoxidable est superficielle la desorption est rapide a 250 degres sous oxygene ou 400 degres sous argon. Si la fixation est de nature chimique il est necessaire de chauffer a des temperatures plus elevees. L adsorption de l iode sur l alumine est res faible et l iode peut etre desorbe rapideemnt. En employant ces materiaux des essais ont ete obtenus sur 300 g de tellure contenant 41 curies d iode 131 avec un bon rendement (98 pour cent). (auteur00.

Micro-Raman spectroscopy studies of bulk and thin films of CuInTe2

International Nuclear Information System (INIS)

Ananthan, M R; Mohanty, Bhaskar Chandra; Kasiviswanathan, S

2009-01-01

Micro-Raman spectroscopy measurements were made on polycrystalline and amorphous thin films of CuInTe 2 as well as bulk polycrystalline CuInTe 2 . Various vibrational modes exhibited by the bulk and polycrystalline thin films were attributed to those expected for single crystal CuInTe 2 . Raman spectra of amorphous films presented a broad spectrum, decomposition of which revealed the presence of elemental tellurium on the film surface. Laser-induced changes on CuInTe 2 thin films were studied by acquiring spectra with higher laser beam power. Modes due to tellurium appeared when the spectra were acquired during laser–sample interaction, indicating tellurium segregation. The Raman spectra measured from polycrystalline films during high laser power irradiation did not show decrease in the intensity of the A 1 mode of CuInTe 2 in spite of loss of tellurium from the lattice. This has been interpreted as related to an increased contribution from the undistorted subsurface CuInTe 2 region at higher excitation power

Religion, sex and politics: Scripting connections in Romans 1:18–32 and Wisdom 14:12–14

Directory of Open Access Journals (Sweden)

Jeremy Punt

2017-08-01

Full Text Available Ancient people envisaged a strong link between what was deemed transgressive religious activities and objectionable sexual practices. Moreover, sexual behaviour considered aberrant was deemed to upset political boundaries which should protect civic and national stability, especially when this behaviour was suspected of effeminacy. Such thinking appears to inform both Romans 1:18–32 and Wisdom of Solomon 14:12–14. Focussing on two passages from these documents, the links between religion, sexual behaviour and politics in the context of the 1st-century Roman Empire are investigated, tracing underlying ideological intersections, connections and divergences.

Human Mu Opioid Receptor (OPRM1A118G) polymorphism is associated with brain mu- opioid receptor binding potential in smokers

Energy Technology Data Exchange (ETDEWEB)

Ray, R.; Logan, J.; Ray, R.; Ruparel, K.; Newberg, A.; Wileyto, E.P.; Loughead, J.W.; Divgi, C.; Blendy, J.A.; Logan, J.; Zubieta, J.-K.; Lerman, C.

2011-04-15

Evidence points to the endogenous opioid system, and the mu-opioid receptor (MOR) in particular, in mediating the rewarding effects of drugs of abuse, including nicotine. A single nucleotide polymorphism (SNP) in the human MOR gene (OPRM1 A118G) has been shown to alter receptor protein level in preclinical models and smoking behavior in humans. To clarify the underlying mechanisms for these associations, we conducted an in vivo investigation of the effects of OPRM1 A118G genotype on MOR binding potential (BP{sub ND} or receptor availability). Twenty-two smokers prescreened for genotype (12 A/A, 10 */G) completed two [{sup 11}C] carfentanil positron emission tomography (PET) imaging sessions following overnight abstinence and exposure to a nicotine-containing cigarette and a denicotinized cigarette. Independent of session, smokers homozygous for the wild-type OPRM1 A allele exhibited significantly higher levels of MOR BP{sub ND} than smokers carrying the G allele in bilateral amygdala, left thalamus, and left anterior cingulate cortex. Among G allele carriers, the extent of subjective reward difference (denicotinized versus nicotine cigarette) was associated significantly with MOR BP{sub ND} difference in right amygdala, caudate, anterior cingulate cortex, and thalamus. Future translational investigations can elucidate the role of MORs in nicotine addiction, which may lead to development of novel therapeutics.

Lasing transition at 1.06 μm emission in Nd3+ -doped borate-based tellurium calcium zinc niobium oxide glasses for high-power solid-state lasers.

Science.gov (United States)

Ravi, O; Prasad, K; Jain, Rajiv; Venkataswamy, M; Chaurasia, Shivanand; Deva Prasad Raju, B

2017-08-01

The spectroscopic properties of Tellurium Calcium Zinc Niobium oxide Borate (TCZNB) glasses of composition (in mol%) 10TeO 2  + 15CaO + 5ZnO + 10 Nb 2 O 5  + (60 - x)B 2 O 3  + Nd 2 O 3 (x = 0.1, 0.5, 1.0 or 1.5 mol%) have been investigated experimentally. The three phenomenological intensity parameters Ω 2 , Ω 4, Ω 6 have been calculated using the Judd-Ofelt theory and in turn radiative properties such as radiative transition probabilities, emission cross-sections, branching ratios and radiative lifetimes have been estimated. The trend found in the JO intensity parameter is Ω 2  > Ω 6  > Ω 4 If Ω 6  > Ω 4 , the glass system is favourable for the laser emission 4 F 3 /2  →  4 I 11 /2 in the infrared (IR) wavelength. The experimental values of branching ratio of 4 F 3 /2  →  4 I 11 /2 transition indicate favourable lasing action with low threshold power. The evaluated total radiative transition probabilities (A T ), stimulated emission cross-section (σ e ) and gain bandwidth parameters (σ e  × Δλ p ) were compared with earlier reports. An energy level analysis has been carried out considering the experimental energy positions of the absorption and emission bands. Copyright © 2016 John Wiley & Sons, Ltd.

Charmed particles production in pA -interactions at √s = 11.8 GeV

Energy Technology Data Exchange (ETDEWEB)

Aleev, A.; Balandin, V.; Boguslavsky, M.; Dunun, V.; Gavrishchuk, O.; Furmanec, N.; Kireev, V.; Konstantinov, V.; Kosarev, I.; Kokoulina, E.; Kuzmin, N.; Lanshikov, G.; Nikitin, V.; Petukhov, Yu.; Rufanov, I.; Topuria, T.; Yukaev, A. [Joint Institute for Nuclear Research, Dubna, Moscow region (Russian Federation); Ardashev, E.; Afonin, A.; Bogolyubsky, M.; Golovnia, S.; Gorokhov, S.; Golovkin, V.; Kholodenko, A.; Kiriyakov, A.; Kurchaninov, L.; Mitrofanov, G.; Moiseev, A.; Petrov, V.; Pleskach, A.; Riadovikov, V.; Ronjin, V.; Senko, V.; Shalanda, N.; Soldatov, M.; Tsyupa, Yu.; Vasiliev, M.; Vorobiev, A.; Yakimchuk, V.; Zapolsky, V.; Zmushko, V. [Institute for High Energy Physics, Protvino, Moscow region (Russian Federation); Basiladze, S.; Bogdanova, G.; Grishin, N.; Grishkevich, Ya.; Ermolov, P.; Karmanov, D.; Kozlov, V.; Kramarenko, V.; Kubarovsky, A.; Larichev, A.; Leflat, A.; Lyutov, S.; Merkin, M.; Orfanitsky, S.; Popov, V.; Tikhonova, L.; Vischnevskaya, A.; Volkov, V.; Voronin, A.; Zotkin, S.; Zotkin, D.; Zverev, E. [Moscow State University, Skobeltsyn Institute of Nuclear Physics (SINP MSU), Federal State Budget Educational Institution of Higher Education M.V. Lomonosov, Moscow (Russian Federation); Collaboration: SVD-2 Collaboration

2017-03-15

The results of the SERP-E-184 experiment at the U-70 accelerator (IHEP, Protvino) are presented. Interactions of the 70GeV proton beam with carbon, silicon and lead targets were studied to detect decays of charmed D{sup 0}, anti D{sup 0}, D{sup +}, D{sup -} mesons and Λ{sub c}{sup +} baryon near their production threshold. Measurements of lifetimes and masses have shown a good agreement with PDG data. The inclusive cross-sections of charm production and their A-dependences have been obtained. The yields of these particles are compared with the theoretical predictions and the data of other experiments. The measured cross-section of the total open charm production (σ{sub tot}(c anti c) = 7.1 ± 2.3(stat) ± 1.4(syst) μb/nucleon) at the collision c.m. energy √s = 11.8 GeV is well above the QCD model predictions. The contributions of different kinds of charmed particles to the total cross-section of the open charm production in proton-nucleus interactions vary with energy. (orig.)

Wind tunnel test on airfoil Riso-B1-18 with an Active Trailing Edge Flap

DEFF Research Database (Denmark)

Bak, Christian; Gaunaa, Mac; Andersen, Peter Bjørn

2010-01-01

A wind tunnel test of the wind turbine airfoil Risø-B1-18 equipped with an Active Trailing Edge Flap (ATEF) was carried out. The ATEF was 9% of the total chord, made of piezo electric actuators attached to the trailing edge of a non-deformable airfoil and actuated using an (electric) amplifier....... The airfoil was tested at Re = 1.66 × 106. Steady state and dynamic tests were carried out with prescribed deflections of the ATEF. The steady state tests showed that deflecting the ATEF towards the pressure side (positive ) translated the lift curve to higher lift values and deflecting the ATEF towards...... the suction side (negative ) translated the lift curve to lower lift values. Testing the airfoil for a step change of the ATEF from = -3.0 to +1.8 showed that the obtainable cl was 0.10 to 0.13 in the linear part of the lift curve. Modeling the step response with an indicial function formulation showed...

Synthesis and reactivity of 10-alkylphenotellurazines

International Nuclear Information System (INIS)

Sadekov, I.D.; Abakarov, G.M.; Panov, V.B.; Ukhin, L.Yu.; Garnovskii, A.D.; Minkin, V.I.

1985-01-01

The reaction of N-alkyl-2,2'-dilithium diphenylamines with tellurium diiodide yields derivatives of a new heterocyclic system, phenotellurazine. 10-Alkyl-phenotellurazines readily form derivatives containing tetra- and tricoordinated tellurium, form complexes with metal salts and rhodium(I) carbonyl chloride and by bromination and nitration give 3,7-dibromo- or 3-nitro-, 3,7-dinitro, and 1,3,7,9-tetranitro derivatives

Radionuclides in diffusion probing of inorganic materials based on chalcogenides

International Nuclear Information System (INIS)

Firsova, L.P.

1994-01-01

Migration of tellurium-125m, selenium-75, sulfur-35 radionuclides in solid solutions Pb 1-y (Se 0.08 Te 0.92 ) y and (Pb 1-x Sn x ) y Te 1-y , where x=0.1 and 0.2, has been studied, the results are presented. Data on dependence of selenium and tellurium self-diffusion coefficients on temperature in the range of 600-750 deg C are given. The results of the study of self-diffusion coefficient isothermal dependences on lead and tellurium vapour pressure in equilibrium with solid phases have been considered. It is ascertained that a change in the temperature and p-n transitions initiate the change in self-diffusion mechanisms of chalcogenide atoms. 8 refs., 3 tabs

Nuclear medicine. Progress report for quarter ending June 30, 1982

Energy Technology Data Exchange (ETDEWEB)

Knapp, F.F. Jr.; Ambrose, K.R.; Butler, T.A.; Goodman, M.M.; Hoeschele, J.D.; Srivastava, P.C.

1982-09-01

The oxidation products of tellurium and selenium fatty acids were shown to differ and may relate to the unique prolonged retention of tellurium fatty acids in the heart. The studies suggest that the trapping of tellurium fatty acids in the heart may result from the formation of an insoluble oxidation product after entry into the cells of the heart muscle. Also described in this report is the synthesis of several barbituric acid analogues for evaluation as potential cerebral perfusion agents. The present studies indicate that the iodovinyl-alkyl barbiturates cross the intact blood-brain barrier but undergo in vivo deiodination as measured by a high uptake of radioiodine in the thyroid. During this period four /sup 191/Os-osmate shipments were made to Medical Cooperative investigators for evaluation of the ultrashort-lived /sup 191//sup m/Ir (T/sub 1/2/ = 4.9 sec) obtained from the /sup 191//sup m/Ir generator. Seven shipments of the /sup 195//sup m/Pt-labeled cis-dichlorodiammineplatinum(II) antitumor drug were made to collaborators and fice shipments of radiolabeled tellurium fatty acids were made to the Massachusetts General Hospital.

Cs_7Sm_1_1[TeO_3]_1_2Cl_1_6 and Rb_7Nd_1_1[TeO_3]_1_2Br_1_6, the new tellurite halides of the tetragonal Rb_6LiNd_1_1[SeO_3]_1_2Cl_1_6 structure type

International Nuclear Information System (INIS)

Charkin, Dmitri O.; Black, Cameron; Downie, Lewis J.; Sklovsky, Dmitry E.; Berdonosov, Peter S.; Olenev, Andrei V.; Zhou, Wuzong; Lightfoot, Philip; Dolgikh, Valery A.

2015-01-01

Two new rare-earth – alkali – tellurium oxide halides were synthesized by a salt flux technique and characterized by single-crystal X-ray diffraction. The structures of the new compounds Cs_7Sm_1_1[TeO_3]_1_2Cl_1_6 (I) and Rb_7Nd_1_1[TeO_3]_1_2Br_1_6 (II) (both tetragonal, space group I4/mcm) correspond to the sequence of [MLn_1_1(TeO_3)_1_2] and [M_6X_1_6] layers and bear very strong similarities to those of known selenite analogs. We discuss the trends in similarities and differences in compositions and structural details between the Se and Te compounds; more members of the family are predicted. - Graphical abstract: Two new rare-earth – alkali – tellurium oxide halides were predicted and synthesized. - Highlights: • Two new rare-earth – alkali – tellurium oxide halides were synthesized. • They adopt slab structure of rare earth-tellurium-oxygen and CsCl-like slabs. • The Br-based CsCl-like slabs have been observed first in this layered family.

Ten Good Reasons for the Use of the Tellurium-Centered Anderson-Evans Polyoxotungstate in Protein Crystallography.

Science.gov (United States)

Bijelic, Aleksandar; Rompel, Annette

2017-06-20

Protein crystallography represents at present the most productive and most widely used method to obtain structural information on target proteins and protein-ligand complexes within the atomic resolution range. The knowledge obtained in this way is essential for understanding the biology, chemistry, and biochemistry of proteins and their functions but also for the development of compounds of high pharmacological and medicinal interest. Here, we address the very central problem in protein crystallography: the unpredictability of the crystallization process. Obtaining protein crystals that diffract to high resolutions represents the essential step to perform any structural study by X-ray crystallography; however, this method still depends basically on trial and error making it a very time- and resource-consuming process. The use of additives is an established process to enable or improve the crystallization of proteins in order to obtain high quality crystals. Therefore, a more universal additive addressing a wider range of proteins is desirable as it would represent a huge advance in protein crystallography and at the same time drastically impact multiple research fields. This in turn could add an overall benefit for the entire society as it profits from the faster development of novel or improved drugs and from a deeper understanding of biological, biochemical, and pharmacological phenomena. With this aim in view, we have tested several compounds belonging to the emerging class of polyoxometalates (POMs) for their suitability as crystallization additives and revealed that the tellurium-centered Anderson-Evans polyoxotungstate [TeW 6 O 24 ] 6- (TEW) was the most suitable POM-archetype. After its first successful application as a crystallization additive, we repeatedly reported on TEW's positive effects on the crystallization behavior of proteins with a particular focus on the protein-TEW interactions. As electrostatic interactions are the main force for TEW binding

Transport properties of fission product vapors

International Nuclear Information System (INIS)

Im, K.H.; Ahluwalia, R.K.

1983-07-01

Kinetic theory of gases is used to calculate the transport properties of fission product vapors in a steam and hydrogen environment. Provided in tabular form is diffusivity of steam and hydrogen, viscosity and thermal conductivity of the gaseous mixture, and diffusivity of cesium iodide, cesium hydroxide, diatomic tellurium and tellurium dioxide. These transport properties are required in determining the thermal-hydraulics of and fission product transport in light water reactors

Nanocrystals of the quaternary thermoelectric materials: AgPb{sub m}SbTe{sub m+2}(m=1-18): Phase-segregated or solid solutions?

Energy Technology Data Exchange (ETDEWEB)

Arachchige, Indika U [Department of Chemistry, Northwestern University Evanston, IL (United States); Wu, Jinsong; Dravid, Vinayak P [Department of Materials Science and Engineering, Northwestern University Evanston, IL (United States); Kanatzidis, Mercouri G [Department of Chemistry, Northwestern University Evanston, IL (United States); Material Science Division, Argonne National Laboratory Argonne, IL (United States)

2008-10-02

Facile synthesis of a series of thermoelectrically relevant AgPb{sub m}SbTe{sub m+2}(m=1-18) nanoparticles is carried out by using a colloidal synthetic route. As-synthesized nanocrystals are spherical in geometry and adopt a cubic NaCl-type structure. These quaternary nanocrystals behave as solid solutions at room temperature and tend to phase separate into AgSbTe{sub 2} and PbTe upon annealing at moderately high temperature. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Coulomb excitation of $^{116}$Te and $^{118}$Te: a study of collectivity above the Z = 50 shell gap

CERN Multimedia

Cederkall, J A; Smith, J F; Voulot, D; Rahkila, P J; Darby, I G; Hadinia, B; Grahn, T; Paul, E S; Wadsworth, R; Bree, N C F; Baeck, T M; Julin, R J; Diriken, J V J; Jenkins, D G; Kroell, T; Leske, J; Huyse, M L

We propose to study the nature and collectivity of low-energy excitations in $^{116}$Te and $^{118}$Te. We aim to measure the transition probability of the 0$^{+}$ $\\rightarrow$ 2$^{+}$ transition by means of Coulomb excitation, employing REX-ISOLDE and MINIBALL. The proposed study probes the systematics of B(E2) values in light Te nuclei, which lie in a region of the nuclear chart where unusual phenomena and evolution of collectivity have been observed. The proposed study will shed light on the role of the residual proton-neutron interactions in the development of collectivity when approaching the N = Z line. This is a resubmission of the P-277 proposal. The suggestions of INTC have been taken into account and the data from the Yale $^{120}$Te study has been included.

Design and construction of a prototype to obtain TeO2

International Nuclear Information System (INIS)

Roque H, I.

1997-01-01

At the National Institute of Nuclear Research is developed the process to produce the radioisotope Iodine 131 which is employed in medicine with therapeutical purposes. The raw material to produce iodine 131 is tellurium dioxide (TeO 2 ). TeO 2 is intended to be produced from a prototype being this aim of this thesis named D esign and construction of a prototype to obtain TeO 2 . The TeO 2 obtained must have specific physicochemical characteristics, being necessary an special design of a prototype which will guarantee the quality of tellurium dioxide obtention. Design and building the final prototype project, was developed in to three stages. At the first stage, the TeO 2 was obtained at the laboratory, this allows to know the basic reaction characteristics. The second stage purpose, was to work with an former prototype which allowed to produce 100 g of tellurium dioxide. In the last stage a depurated chemical process parameters was made and the prototype was refined in regard to its mechanical design, giving us as result the final prototype. With this final prototype, the production reaches 2 Kg/week of tellurium dioxide with the best physicochemical properties which is to be employed as raw material in order to produce iodine 131. (Author)

Out-of-pile experiments of fuel-cladding chemical interaction, (2)

International Nuclear Information System (INIS)

Konashi, Kenji; Yato, Tadao; Kaneko, Hiromitsu; Honda, Yutaka

1980-01-01

Cesium seems to be one of the most important fission products in the fuel-cladding chemical interaction of fuel pins for LMFBRs. However the FCCI under irradiation cannot always be explained by considering only cesium-oxygen system as the corrosive, since attack does not occur in the cesium-oxygen system unless oxygen potential is sufficiently high. Cesium-tellurium-oxygen system has been proposed to account for heavy cladding attack which was sometimes found in hypostoichiometric mixed oxide fuel pins. In this paper, the experiment on the reaction of liquid tellurium with stainless steel is reported. The type 316 stainless steel claddings for Monju type fuel pins were used as the test specimens. Tellurium was contained into the cladding tubes with end plugs. The temperature dependence of the attack by tellurium was examined in the range from 450 to 900 deg C for 30 min, and the heating time dependence was examined from 5 min to 200 hr at 725 deg C. An infrared lamp furnace was used for the experiment within 7 hr, and a resistance furnace for longer experiment. The character of corrosion was matrix attack, and the reaction products on the stainless steel surfaces consisted of chrome rich inner phase and iron and nickel rich outer phase. The results are reported. (Kako, I.)

Terahertz and infrared transmission of an organic/inorganic hybrid thermoelectric material

International Nuclear Information System (INIS)

Heyman, J. N.; Alebachew, B. A.; Kaminski, Z. S.; Nguyen, M. D.; Coates, N. E.; Urban, J. J.

2014-01-01

We report terahertz and infrared transmission measurements of a high-performance thermoelectric material containing tellurium nanowires in a conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) matrix. The DC electrical conductivity of the hybrid material (41 S/cm) is approximately one hundred times that of pure PEDOT:PSS and more than 400 times that of a film of pure tellurium nanowires, while the terahertz-frequency (THz) conductivity of PEDOT:PSS and the hybrid material are comparable at f ∼ 2THz. A frequency-dependent conductivity model indicates that the increased DC conductivity of the hybrid material results from an increase in the DC charge mobility rather than in the free charge density. We suggest that the increased DC conductivity of the hybrid material results from an increase in linkage between PEDOT domains by the tellurium nanowires

Terahertz and infrared transmission of an organic/inorganic hybrid thermoelectric material

Energy Technology Data Exchange (ETDEWEB)

Heyman, J. N., E-mail: heyman@macalester.edu; Alebachew, B. A.; Kaminski, Z. S.; Nguyen, M. D. [Physics Department, Macalester College, St. Paul, Minnesota 55105 (United States); Coates, N. E.; Urban, J. J. [The Molecular Foundry, Materials Science Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2014-04-07

We report terahertz and infrared transmission measurements of a high-performance thermoelectric material containing tellurium nanowires in a conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) matrix. The DC electrical conductivity of the hybrid material (41 S/cm) is approximately one hundred times that of pure PEDOT:PSS and more than 400 times that of a film of pure tellurium nanowires, while the terahertz-frequency (THz) conductivity of PEDOT:PSS and the hybrid material are comparable at f ∼ 2THz. A frequency-dependent conductivity model indicates that the increased DC conductivity of the hybrid material results from an increase in the DC charge mobility rather than in the free charge density. We suggest that the increased DC conductivity of the hybrid material results from an increase in linkage between PEDOT domains by the tellurium nanowires.

Occurency and aqueous processing of tellurides from Sonora (Mexico)

International Nuclear Information System (INIS)

Aguayo, S.; Perez, E.; Ecinas, M.A.

1996-01-01

Tellurium production is limited mainly to that obtained from the treatment of electrolyte muds from copper refineries. however, there are several other sources from which the precious metal tellurides are potentially attractive. This work presents a review of the main localitiesin Sonora (Mexico), where tellurides have been found. In addition, based upon the physical chemistry fundamentals for tellurium and precious metal tellurides, the aqueous extraction and recovery routes are discussed. (Author) 51 refs

Crystal structure of the mixed-metal thiophosphate Nb1.18V0.82PS10

Directory of Open Access Journals (Sweden)

Joobin Sun

2015-03-01

Full Text Available The mixed-metal thiophosphate, Nb1.18V0.82PS10 (niobium vanadium phosphorus decasulfide, has been prepared though solid state reactions using an alkali-metal halide flux. The title compound is isostructural with two-dimensional Nb2PS10. [M2S12] (M = Nb or V dimers built up from two bicapped trigonal prisms and tetrahedral [PS4] units share sulfur atoms to construct 1∞[M2PS10] chains along the a axis. These chains are linked through the disulfide bonds between [PS4] units in adjacent chains to form layers parallel to the ab plane. These layers then stack on top of each other to complete the three-dimensional structure with van der Waals gaps. The M sites are occupied by 59% of Nb and 41% of V and the average M—S and M—M distances in the title compound are in between those of V2PS10 and Nb2PS10. The classical charge balance of the title compound can be represented by [(Nb/V4+]2[P5+][S2−]3[S−]7.

Novel method of producing radioactive iodine

International Nuclear Information System (INIS)

Shikata, E.; Amano, H.

1976-01-01

Radioactive iodine(I-131) is easily obtained by heating, at a temperature ranging from 600 0 C to 650 0 C, a tellurium oxide intermediate which was obtained by heating telluric acid or tellurium trioxide at a temperature from about 400 0 C to 560 0 C and was irradited with a neutron flux. Thus, pure I-131 is obtained without the complicated operations required in a conventional process for separation and/or purification of the product. 4 claims

Single crystal growth and structure refinements of CsMxTe2-xO6 (M = Al, Ga, Ge, In) pyrochlores

International Nuclear Information System (INIS)

Siritanon, Theeranun; Sleight, A.W.; Subramanian, M.A.

2011-01-01

Graphical abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown and structure refinements indicate deviations from ideal stoichiometry presumably related to mixed valency of tellurium. Highlights: → Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown. → Structure refinements from single crystal X-ray diffraction data confirm e structure. → Deviations from ideal stoichiometry suggest mixed valency of tellurium and hence conductivity. -- Abstract: Single crystals of CsM x Te 2-x O 6 pyrochlores with M = Al, Ga, Ge, and In have been grown from a TeO 2 flux. Structure refinements from single crystal X-ray diffraction data are reported. These results are used to discuss deviations from ideal stoichiometry that result in electronic conductivity presumably related to mixed valency of tellurium.

Computational study of the Risø-B1-18 airfoil with a hinged flap providing variable trailing edge geometry

DEFF Research Database (Denmark)

Troldborg, Niels

2005-01-01

A comprehensive computational study, in both steady and unsteady flow conditions, has been carried out to investigate the aerodynamic characteristics of the Risø-B1.18 airfoil equipped with variable trailing edge geometry as produced by a hinged flap. The function of such flaps should...... on the baseline airfoil showed excellent agreement with measurements on the same airfoil with the same specified conditions. Furthermore, a more widespread comparison with an advanced potential theory code is presented. The influence of various key parameters, such as flap shape, flap size and oscillating...... frequencies, was investigated so that an optimum design can be suggested for application with wind turbine blades. It is concluded that a moderately curved flap with flap chord to airfoil curve ratio between 0.05 and 0.10 would be an optimum choice....

PCB-153 shows different dynamics of mobilisation from differentiated rat adipocytes during lipolysis in comparison with PCB-28 and PCB-118.

Science.gov (United States)

Louis, Caroline; Tinant, Gilles; Mignolet, Eric; Thomé, Jean-Pierre; Debier, Cathy

2014-01-01

Polychlorinated biphenyls (PCBs) are persistent organic pollutants. Due to their lipophilic character, they are preferentially stored within the adipose tissue. During the mobilisation of lipids, PCBs might be released from adipocytes into the bloodstream. However, the mechanisms associated with the release of PCBs have been poorly studied. Several in vivo studies followed their dynamics of release but the complexity of the in vivo situation, which is characterised by a large range of pollutants, does not allow understanding precisely the behaviour of individual congeners. The present in vitro experiment studied the impact of (i) the number and position of chlorine atoms of PCBs on their release from adipocytes and (ii) the presence of other PCB congeners on the mobilisation rate of such molecules. Differentiated rat adipocytes were used to compare the behaviour of PCB-28, -118 and -153. Cells were contaminated with the three congeners, alone or in cocktail, and a lipolysis was then induced with isoproterenol during 12 hours. Our data indicate that the three congeners were efficiently released from adipocytes and accumulated in the medium during the lipolysis. Interestingly, for a same level of cell lipids, PCB-153, a hexa-CB with two chlorine atoms in ortho-position, was mobilised slower than PCB-28, a tri-CB, and PCB-118, a penta-CB, which are both characterised by one chlorine atom in ortho-position. It suggests an impact of the chemical properties of pollutants on their mobilisation during periods of negative energy balance. Moreover, the mobilisation of PCB congeners, taken individually, did not seem to be influenced by the presence of other congeners within adipocytes. These results not only highlight the obvious mobilisation of PCBs from adipocytes during lipolysis, in parallel to lipids, but also demonstrate that the structure of congeners defines their rate of release from adipocytes.

Constitutional studies in the palladium-rhodium-tellurium (-oxygen) system. A contribution to elucidate the behaviour of Pd, Rh and Te in the vitrification process of high-level waste concentrates (HLWC)

International Nuclear Information System (INIS)

Hartmann, T.

1996-01-01

In the vitrification process of high-level waste concentrates (HLWC) from the reprocessing of nuclear spent fuel elements, about 30 different elements have to be immobilized in a solid matrix consisting of an alkali borosilicate glass. Most of the waste oxides are dissolved in the alkali borosilicate melt and become structural elements of the glasses when cooled. This, however, applies only partly to the platinum metals Ru, which forms RuO 2 , and palladium and rhodium, which deposit as sparingly soluble and electrically conducting tellurides. This might considerably impair the technical process of HLWC vitrification. Therefore, constitutional studies on the Pd-Rh-Te system became necessary. The phase diagram of the Pd-Rh-Te ternary system at temperatures of 1150, 1100, 1050, 1000, 950, 900 and 750 C was determined under inertial conditions. Oxygen exerts a major influence on the system. Already under limited availability of oxygen, the rhodium contents of the solid solution phases α 1 and α 2 are clearly diminished. Rhodium of the phases becomes oxidized selectively. The three-phase field α 1 +α 2 +L is shifted to higher palladium and tellurium contents, even oxygen is available to a limited extend only. With the oxygen in the air, the extension of the three-phase space is reduced markedly. The complex process chemistry of Pf, Rh and Te during the vitrification can be described by the state of the Pd-Rh-Te ternary system after annealing in (air) oxygen for limited periods of time. (orig./MM) [de

Degenerative myelopathy in German Shepherd Dog: comparison of two molecular assays for the identification of the SOD1:c.118G>A mutation.

Science.gov (United States)

Capucchio, Maria Teresa; Spalenza, Veronica; Biasibetti, Elena; Bottero, Maria Teresa; Rasero, Roberto; Dalmasso, Alessandra; Sacchi, Paola

2014-02-01

Degenerative myelopathy (DM) is a late-onset, slowly progressive degeneration of spinal cord white matter which is reported primarily in large breed dogs. The missense mutation SOD1:c.118G>A is associated with this pathology in several dog breeds, including the German Shepherd Dog (GSD). The aims of the present study were to develop a tool for the rapid screening of the SOD1 mutation site in dogs and to evaluate the association of the polymorphism with DM in the German Shepherd breed. Two different techniques were compared: a minisequencing test and a real-time pcr allelic discrimination assay. Both approaches resulted effective and efficient. A sample of 47 dogs were examined. Ten subjects presented the symptoms of the illness; for one of them the diagnosis was confirmed by postmortem investigations and it resulted to be an A/A homozygote. In another clinically suspected dog, heterozygote A/G, the histopathological examination of the medulla showed moderate axon and myelin degenerative changes. GSD shows a frequency of the mutant allele equal to 0.17, quite high being a high-risk allele. Because canine DM has a late onset in adulthood and homozygous mutant dogs are likely as fertile as other genotypes, the natural selection is mild and the mutant allele may reach high frequencies. A diagnostic test, easy to implement, may contribute to control the gene diffusion in populations. The SOD1:c.118G>A mutation could be a useful marker for breeding strategies intending to reduce the incidence of DM.

Evaluation of radioactive wastes in Instituto de Energia Atomica (Sao Paulo-Brazil)

International Nuclear Information System (INIS)

Sawakuchi, R.S.

1978-01-01

An evaluation of present and future production of radioactive waste in several departments of the Instituto de Energia Atomica has been done. Taking into account this evaluation, the criteria for disposal and convenient treatment technique have been studied. The most critical form of liquid radioactive waste is that of 131 I processing because high concentration of radiotellurium always accompanies this form of waste. Ion exchange and precipitation techniques were used to study this waste processing. Two kinds of resins were used by the ion exchange method: the strong anionic and the stron cationic. Quantitative tellurium retention has not been attained by the ion exchange method using either resins. The technique of precipitation of radioactive tellurium as ammonium tellurate was also used, allowing us to obtain more than 99% of tellurium removal. The remaining radioactive wastes can be eliminated using the storage for decay criteria with further release to the sewers in the case of liquids and burial in the case of solids. (Author) [pt

Proceedings of the Japan-U.S. workshop P-118 on vacuum technologies for fusion devices

International Nuclear Information System (INIS)

Miyahara, A.

1989-01-01

Fusion community does not appreciate vacuum technologies to the same extent as accelerator community does. This is because, in the case of accelerators, in particular storage ring systems, the requirement of attaining ultrahigh vacuum in order to avoid collisional loss is well defined, on the other hand, it is not possible to define the requirement so precisely in the case of fusion devices. One of the reasons is that core plasma interacts with vessel wall so strongly and unpredictably that it becomes difficult to identify the role played by individual components. However, in the next step and the next generation machines like CIT, LHS, ITER, FER and NET, vacuum technologies would play more significant roles, because the CIT will introduce tritium in a vacuum vessel, and the aim of the ITER project is to demonstrate particle balance, namely, to achieve steady state operation with D-T fuel. The Japan-U.S. workshop P-118 was held at the Institute of Plasma Physics, Nagoya University, from August 1 to 5, 1988. 33 participants including 4 from the U.S. took part in the workshop. In the plenary session, 12 lectures were given, and also the topics-oriented session on pumping, gauging, remote maintenance, first wall, pump limiter, divertor and others was held. (K.I.)

Electrical Resistivity Investigation of Gas Hydrate Distribution in Mississippi Canyon Block 118, Gulf of Mexico

Energy Technology Data Exchange (ETDEWEB)

Dunbar, John

2012-12-31

Electrical methods offer a geophysical approach for determining the sub-bottom distribution of hydrate in deep marine environments. Methane hydrate is essentially non-conductive. Hence, sediments containing hydrate are more resistive than sediments without hydrates. To date, the controlled source electromagnetic (CSEM) method has been used in marine hydrates studies. This project evaluated an alternative electrical method, direct current resistivity (DCR), for detecting marine hydrates. DCR involves the injection of direct current between two source electrodes and the simultaneous measurement of the electric potential (voltage) between multiple receiver electrodes. The DCR method provides subsurface information comparable to that produced by the CSEM method, but with less sophisticated instrumentation. Because the receivers are simple electrodes, large numbers can be deployed to achieve higher spatial resolution. In this project a prototype seafloor DCR system was developed and used to conduct a reconnaissance survey at a site of known hydrate occurrence in Mississippi Canyon Block 118. The resulting images of sub-bottom resistivities indicate that high-concentration hydrates at the site occur only in the upper 50 m, where deep-seated faults intersect the seafloor. Overall, there was evidence for much less hydrate at the site than previously thought based on available seismic and CSEM data alone.

Strong anisotropy effect in an iron-based superconductor CaFe0.882Co0.118AsF

Science.gov (United States)

Ma, Yonghui; Ji, Qiucheng; Hu, Kangkang; Gao, Bo; Li, Wei; Mu, Gang; Xie, Xiaoming

2017-07-01

The anisotropy of iron-based superconductors is much smaller than that of the cuprates and that predicted by theoretical calculations. A credible understanding for this experimental fact is still lacking up to now. Here we experimentally study the magnetic-field-angle dependence of electronic resistivity in the superconducting phase of an iron-based superconductor CaFe{}0.882Co{}0.118AsF, and find the strongest anisotropy effect of the upper critical field among the iron-based superconductors based on the framework of Ginzburg-Landau theory. The evidence of the energy band structure and charge density distribution from electronic structure calculations demonstrates that the observed strong anisotropic effect mainly comes from the strong ionic bonding in between the ions of Ca2+ and F-, which weakens the interlayer coupling between the layers of FeAs and CaF. This finding provides a significant insight into the nature of the experimentally-observed strong anisotropic effect of electronic resistivity, and also paves the way for designing exotic two-dimensional artificial unconventional superconductors in the future.

Thermoelectric properties of P-type Sb2Te3 thick film processed by a screen-printing technique and a subsequent annealing process

International Nuclear Information System (INIS)

Kim, Sun Jin; We, Ju Hyung; Kim, Jin Sang; Kim, Gyung Soo; Cho, Byung Jin

2014-01-01

Highlights: • We report on thermoelectric properties of screen-printed Sb 2 Te 3 thick film. • Subsequent annealing process determines thermoelectric properties of Sb 2 Te 3 film. • Annealing in tellurium powder ambient contributes to tellurium-rich Sb 2 Te 3 film. • Annealing in tellurium powder ambient enhances carrier mobility of Sb 2 Te 3 film. -- Abstract: We herein report the thermoelectric properties of Sb 2 Te 3 thick film fabricated by a screen-printing technique and a subsequent annealing process. Each step of the screen-printing fabrication process of Sb 2 Te 3 thick film is described in detail. It was found that the subsequent annealing process must be carefully designed to achieve good thermoelectric properties of the screen-printed film. The results show that the annealing of the screen-printed Sb 2 Te 3 thick film together with tellurium powder in the same process chamber significantly improves the carrier mobility by increasing the average scattering time of the carrier in the film, resulting in a large improvement of the power factor. By optimizing the annealing process, we achieved a maximum thermoelectric figure-of-merit, ZT, of 0.32 at room temperature, which is slightly higher than that of bulk Sb 2 Te 3 . Because screen-printing is a simple and low-cost process and given that it is easy to scale up to large sizes, this result will be useful for the realization of large, film-type thermoelectric devices

Pengaruh unsur Tembaga (Cu terhadap fluiditas paduan Al-Si 11.8 wt% (ADC 12 dengan metode Vacuum Suction Test

Directory of Open Access Journals (Sweden)

Bambang Suharno

2012-11-01

Full Text Available Al-Si 11.8 wt% alloy which classified to eutectic Al-Si composition usually used to produce a flat casting product with high pressure die casting process. Alloying element become an important things to determine behavior and characteristic of aluminum. Copper added into aluminum to improve strength and hardness, but there has no many studies on the effect of copper on fluidity. This fluidity study is using vacuum suction test method and the microstructure is observed with SEM/EDS. Spectrometer test has been used to find out chemical composition of sample. The result of this study shows that with copper addition from 2.25 wt% to 3.11 wt%, the fluidity value has increased 24.11% on 680oC pouring temperature. On 3.11 wt% copper composition, fluidity value has increased 14.38% from 640oC pouring temperature to 700oC pouring temperature.

Electrical Properties of Ba3Ca1.18Nb1.82O9-  Proton-Conducting Electrolyte Prepared by a Combustion Method

KAUST Repository

Bi, Lei

2013-10-07

Ba3Ca1.18Nb1.82O9-δ (BCN18), regarded as a promising proton-conducting electrolyte material for solid oxide fuel cells, is usually synthesized by a solid-state reaction because of the limited choice of Nb precursors. This study presents a wet chemical route for preparing BCN18 powders that were then sintered into pellets. Electrochemical impedance spectroscopy studies indicated that BCN18 pellets show proton conductivity, since their total conductivity in wet air was significantly larger than that in dry air. However, a detailed analysis showed that only the BCN18 bulk behaves as a proton conductor, while its grain boundary conductivity did not increase in wet air.

Synthesis and characterization of the [Te(SCN2H4)4] (SO4)2 complex. Application to the separation of 99Mo from fission products

International Nuclear Information System (INIS)

Mestnik, S.A.C.; Silva, C.P.G. da.

1988-10-01

Thiourea reacts with tellurium-IV ions, in sulfuric medium, to form cationic complex which is strongly retained on cationic ion exchanger. The method was applied to separate 99 Mo from 132 Te obtained in the fission of 235 U since molybdenum does not form such complex and passes throught the cationic exchanger column in the molibdate form. In this paper, the procedure of the tellurium-thiourea complex preparation and its characterization are described. Elemental analysis, ultraviolet and infra-red absorption spectrophotometry as well as thermogravimetry were used to characterize the complex. (author) [pt

White blood cell count, absolute neutrophil count, as predictors of hidden bacterial infections in febrile children 1-18 months of age without focus

International Nuclear Information System (INIS)

AL-Majali, R.M.

2004-01-01

Objectives: To study the relationship between White Blood Cell (WBC), Absolute Neutrophil Count (ANC) in febrile children 1-18 months of age as predictor of bacterial infection, so as to improve our predictability of bacterial infections in emergency room to decrease unnecessary admissions and antibiotic use. Methods: Retrospective review was performed on febrile patients 1-18 months of age that were admitted to hospital between August 2002 and March 2003 on the presumptive diagnosis of fever without focus, Complete septic work up was done for all patients according to local hospital protocol including Complete blood count (CBC), blood culture, urine culture, Chest X-Ray (CXR) and lumbar puncture, Patients who had history of antibiotics use within 48 hours of admission were excluded from the study, History, physical examination, laboratory and radiology data were reviewed. Data about the age, sex, temperature, presence or absence of focal bacterial infection, WBC, ANC, CXR report and body fluid culture results were collected and analyzed. Results: Thirty-four patients were reviewed in this study, Eight patients (23.5%) had bacterial infection: classified as group (2 patchy pneumonia, 3 Urinary tract infection (UTI), 2 meningitis, 1 Occult bacteremia (OB) and 26 patients (76.5%) had no evidence of bacterial infection, classified as group 2, No significant difference was found between the two groups in respect to age, sex, temperature and WBC P>0.05, while there was a significant difference between the two groups in respect to the ANC P = 0.02, also ANC had better sensitivity (78%) and specificity (89%) than WBC (sensitivity 77%, specificity 62%). Conclusion: ANC is a good predictive test for determining bacterial infection in young febrile children without focus, However there is need for other more reliable rapid cost effective measures in dealing with young febrile children at emergency department. (author)

ABCB1 haplotype and OPRM1 118A > G genotype interaction in methadone maintenance treatment pharmacogenetics

Directory of Open Access Journals (Sweden)

Barratt DT

2012-04-01

deviation 35 ± 5 versus 180 ± 65 mg/day, P < 0.01 and Ctrough (78 ± 22 versus 177 ± 97 ng/mL, P < 0.05 than ABCB1 wild-type subjects. Among subjects with the most common ABCB1 haplotype combination (wild-type with 61A:1199G:1236T:2677T:3435T, the OPRM1 118 A/G genotype was associated with a significantly higher Ctrough than 118 A/A (250 ± 126 versus 108 ± 36 ng/mL, P = 0.016. No ABCB1 haplotype group or OPRM1 genotype was associated with dose or Ctrough without taking into account confounding genetic variability at the other locus. Therefore, two interacting pharmacogenetic determinants of methadone maintenance treatment response were identified, ie, ABCB1, where variants are associated with lower methadone requirements, and OPRM1, where the variant is associated with higher methadone requirements.Conclusion: These opposing pharmacogenetic effects therefore need to be considered in combination when assessing methadone maintenance treatment pharmacogenetics.Keywords: methadone, opiate substitution treatment, ABCB1, P-glycoprotein, OPRM1, receptors, opioid, mu

Focal cortical dysplasia type IIa and IIb: MRI aspects in 118 cases proven by histopathology

Energy Technology Data Exchange (ETDEWEB)

Colombo, Nadia; Citterio, Alberto [Ospedale Ca Granda Niguarda, Department of Neuroradiology, Milano (Italy); Tassi, Laura; Mai, Roberto; Sartori, Ivana; Cardinale, Francesco; Lo Russo, Giorgio [Ospedale Niguarda, Claudio Munari Epilepsy Surgery Center, Milano (Italy); Deleo, Francesco; Spreafico, Roberto [IRCCS Foundation Neurological Institute ' ' C. Besta' ' , Department of Epilepsy Clinic and Experimental Neurophysiology, Milano (Italy); Bramerio, Manuela [Ospedale Niguarda, Department of Pathology, Milano (Italy)

2012-10-15

This study aims to review the magnetic resonance imaging (MRI) aspects of a large series of patients with focal cortical dysplasia type II (FCD II) and attempt to identify distinctive features in the two histopathological subtypes IIa and IIb. We retrospectively reviewed the MRI scans of 118 patients with histological proven FCD IIa (n = 37) or IIb (n = 81) who were surgically treated for intractable epilepsy. MRI was abnormal in 93 patients (79 %) and unremarkable in 25 (21 %). A dysplastic lesion was identified in 90 cases (97 %) and classified as FCD II in 83 and FCD non-II in seven cases. In three cases, the MRI diagnosis was other than FCD. There was a significant association between the presence of cortical thickening (p = 0.002) and the ''transmantle sign'' (p < 0.001) and a correct MRI diagnosis of FCD II. MRI positivity was more frequent in the patients with FCD IIb than in those with FCD IIa (91 % vs. 51 %), and the detection rate of FCD II was also better in the patients with type IIb (88 % vs. 32 %). The transmantle sign was significantly more frequent in the IIb subgroup (p = 0.003). The rates of abnormal MRI results and correct MRI diagnoses of FCD II were significantly higher in the IIb subgroup. Although other MRI stigmata may contribute to the diagnosis, the only significant correlation was between the transmantle sign and FCD IIb. (orig.)

Clay-mineral assemblages from some levels of K-118 drill core of Maha Sarakham evaporites, northeastern Thailand

Science.gov (United States)

Suwanich, Parkorn

Clay-mineral assemblages in Middle Clastic, Middle Salt, Lower Clastic, Potash Zone, and Lower Salt, totalling 13 samples from K-118 drill core, in the Maha Sarakham Formation, Khorat Basin, northeastern Thailand were studied. The clay-size particles were separated from the water-soluble salt by water leaching. Then the samples were leached again in the EDTA solution and separated into clay-size particles by using the timing sedimentation. The EDTA-clay residues were divided and analyzed by using the XRD and XRF method. The XRD peaks show that the major-clay minerals are chlorite, illite, and mixed-layer corrensite including traces of rectorite? and paragonite? The other clay-size particles are quartz and potassium feldspar. The XRF results indicate Mg-rich values and moderate MgAl atom ratio values in those clay minerals. The variable Fe, Na, and K contents in the clay-mineral assemblages can explain the environment of deposition compared to the positions of the samples from the core. Hypothetically, mineralogy and the chemistry of the residual assemblages strongly indicate that severe alteration and Mg-enrichment of normal clay detritus occurred in the evaporite environment through brine-sediment interaction. The various Mg-enrichment varies along the various members reflecting whether sedimentation is near or far from the hypersaline brine.

A118

Directory of Open Access Journals (Sweden)

A. Kozlov

2015-11-01

It can be concluded that expression of protogenes, evolutionarily young and/or novel genes in tumors might be a new biological phenomenon, a phenomenon of carcino-evo-devo genes, predicted by the hypothesis of evolution by tumor neofunctionalization.

Computational study of the Risoe-B1-18 airfoil with a hinged flap providing variable trailing edge geometry

Energy Technology Data Exchange (ETDEWEB)

Troldborg, N.

2005-03-01

A comprehensive computational study, in both steady and unsteady flow conditions, has been carried out to investigate the aerodynamic characteristics of the Risoe-B1-18 airfoil equipped with variable trailing edge geometry as produced by a hinged flap. The function of such flaps should be to decrease fatigue-inducing oscillations on the blades. The computations were conducted using a 2D incompressible RANS solver with a k-w turbulence model under the assumption of a fully developed turbulent flow. The investigations were conducted at a Reynolds number of Re = 1.6 - 10{sup 6}. Calculations conducted on the baseline airfoil showed excellent agreement with measurements on the same airfoil with the same specified conditions. Furthermore, a more widespread comparison with an advanced potential theory code is presented. The influence of various key parameters, such as flap shape, flap size and oscillating frequencies, was investigated so that an optimum design can be suggested for application with wind turbine blades. It is concluded that a moderately curved flap with flap chord to airfoil curve ratio between 0.05 and 0.10 would be an optimum choice. (author)

Dissolution and growth of precipitates under electron irradiation in an Al-11.8 at % Zn alloy by small angle neutron scattering

International Nuclear Information System (INIS)

Baig, M.R.

1995-01-01

Dissolution and growth of precipitates in a room temperature aged Al-11.8 at % Zn alloy have been studied under electron irradiation using small angle neutron scattering (SANS). A series of electron irradiations were performed on each sample and SANS measurements were made on each irradiation. In general for low doses the results show an initial decrease in the magnitude of the scattering, but associated with an increase in the precipitate size. This is followed on prolonged irradiation by an increase in the magnitude of the scattering with a continued increase in precipitate size. It is believed, that at low doses some precipitate grow in size but others may dissolve in the matrix, which then becomes supersaturated. With the enhanced rate of diffusion as a result of the irradiation, the remaining precipitates grow rapidly. As the supersaturation reduces, a coarsening mechanism takes over, via a radiation enhanced diffusion mechanism

Aspects of a Distinct Cytotoxicity of Selenium Salts and Organic Selenides in Living Cells with Possible Implications for Drug Design

Directory of Open Access Journals (Sweden)

Ethiene Castellucci Estevam

2015-07-01

Full Text Available Selenium is traditionally considered as an antioxidant element and selenium compounds are often discussed in the context of chemoprevention and therapy. Recent studies, however, have revealed a rather more colorful and diverse biological action of selenium-based compounds, including the modulation of the intracellular redox homeostasis and an often selective interference with regulatory cellular pathways. Our basic activity and mode of action studies with simple selenium and tellurium salts in different strains of Staphylococcus aureus (MRSA and Saccharomyces cerevisiae indicate that such compounds are sometimes not particularly toxic on their own, yet enhance the antibacterial potential of known antibiotics, possibly via the bioreductive formation of insoluble elemental deposits. Whilst the selenium and tellurium compounds tested do not necessarily act via the generation of Reactive Oxygen Species (ROS, they seem to interfere with various cellular pathways, including a possible inhibition of the proteasome and hindrance of DNA repair. Here, organic selenides are considerably more active compared to simple salts. The interference of selenium (and tellurium compounds with multiple targets could provide new avenues for the development of effective antibiotic and anticancer agents which may go well beyond the traditional notion of selenium as a simple antioxidant.

Forming Glasses from Se and Te

Directory of Open Access Journals (Sweden)

Pierre Lucas

2009-10-01

Full Text Available Despite being close neighbors on the Periodic Table, selenium and tellurium present a totally different abilities to form glasses. Se is a very good glass former, and gives rise to numerous glass compositions which are popular for their transparency in the infrared range and their stability against crystallization. These glasses can be shaped into sophisticated optical devices such as optical fibers, planar guides or lenses. Nevertheless, their transparencies are limited at about 12 μm (depending on the thickness of the optical systems due to the relatively small mass of the Se element. On the other hand, tellurium is heavier and its use in substitution for Se permits to shift the IR cutoff beyond 20 μm. However, the semimetallic nature of Te limits its glass formation ability and this glass family is known to be unstable and consequently has found application as phase change material in the Digital Versatile Disk (DVD technology. In this paper, after a review of selenide glasses and their applications, it will be shown how, in a recent past, it has been possible to stabilize tellurium glasses by introducing new elements like Ga or I in their compositions.

Rare (Earth Elements [score

Directory of Open Access Journals (Sweden)

Camilo Méndez

2014-12-01

Full Text Available Rare (Earth Elements is a cycle of works for solo piano. The cycle was inspired by James Dillon’s Book of Elements (Vol. I-V. The complete cycle will consist of 14 pieces; one for each selected rare (earth element. The chosen elements are Neodymium, Erbium, Tellurium, Hafnium, Tantalum, Technetium, Indium, Dysprosium, Lanthanium, Cerium, Europium, Terbium, Yttrium and Darmstadtium. These elements were selected due to their special atomic properties that in many cases make them extremely valuable for the development of new technologies, and also because of their scarcity. To date, only 4 works have been completed Yttrium, Technetium, Indium and Tellurium.

Anisotropic Light Diffraction by Ultrasound in Crystals with Strong Acoustic Anisotropy

Science.gov (United States)

Voloshin, Andrey S.; Balakshy, Vladimir I.

In modern acousto-optics, crystalline materials are used predominantly for manufacturing acousto-optic instruments. Among these materials, such crystals as paratellurite, tellurium, calomel, TAS and some others occupy a prominent place, which are distinguished by exceptionally large anisotropy of acoustic properties. In this work, the influence of acoustic beam energy walk-off on characteristics of Bragg diffraction of light is studied by the example of tellurium crystal. It is shown that the walk-off can substantially change angular and frequency ranges, resulting in their narrowing or broadening subject to position of the operating point in the Bragg angle frequency characteristic. Coefficients of broadening are introduced for characterization of this effect.

Phase relations in the Cu-Te-S system at temperatures between 350 and 900 degree C

DEFF Research Database (Denmark)

Karup-Møller, Sven

1994-01-01

data and optical data on phases A and B are listed. At 350 degree C there exist two liquid fields which at 450 degree C have become one continuous field stretching from Cu45Te55 with low S content to the tellurium corner of the phase diagram and from there to the sulphur corner. With increasing S......, the Cu content of the liquid rapidly decreases to trace amonts. With increasing temperature the field extends into the ternary from the tellurium corner towards the Cu-S join. The boundary of the liquid field in the central portion of the phae diagram towards the sulphur corner does not change position...

Segregation of the elements of the platinum group in a simulated high-level waste glass

International Nuclear Information System (INIS)

Mitamura, H.; Banba, T.; Kamizono, H.; Kiriyama, Y.; Kumata, M.; Murakami, T.; Tashiro, S.

1983-01-01

Segregation of the elements of the platinum group occurred during vitrification of the borosilicate glass containing 20 wt% simulated high-level waste oxides. The segregated materials were composed of two crystalline phases: one was the solid solution of ruthenium and rhodium dioxides and the other was that of palladium and rhodium metals also with tellurium. The segregated materials were not distributed homogeneously throughout the glass: (i) on the surface of the glass, there occurred palladium, rhodium and tellurium alloy alone; and (ii) at the inner part of the glass, the agglomerates of the two phases were concentrated in one part and dispersed in the other

Reactive ion etching of tellurite and chalcogenide waveguides using hydrogen, methane, and argon

International Nuclear Information System (INIS)

Vu, K. T.; Madden, S. J.

2011-01-01

The authors report in detail on the reactive plasma etching properties of tellurium and demonstrate a high quality etching process using hydrogen, methane, and argon. Very low loss planar ridge waveguides are demonstrated. Optical losses in tellurium dioxide waveguides below 0.1 dB/cm in most of the near infrared region of the electromagnetic spectrum and at 1550 nm have been achieved--the lowest ever reported by more than an order of magnitude and clearly suitable for planar integrated devices. The etch process is also shown to be suitable for chalcogenide glasses which may be of importance in applications such as phase change memory devices and nonlinear integrated optics.

Prelaunch Performance of the 118 GHz Polarcube 3U Cubesat Temperature Sounding Radiometer

Science.gov (United States)

Periasamy, L.; Gasiewski, A. J.; Gallaher, D. W.; Sanders, B. T.; Belter, R.; Kraft, D.; Castillo, J.; Gordon, J. A.; Hurowitz, M.

2017-12-01

The low cost PolarCube 3U CubeSat supports a 118.75 GHz imaging spectrometer for temperature profiling of the troposphere and surface temperature. It is a demonstrator for a constellation of LEO passive microwave sensors at V-band and other frequencies using 3U/6U CubeSats. Such a satellite constellation for weather forecasting will provide data at high spatial and temporal resolution to observe rapidly evolving mesoscale weather. The satellite's payload is an eight channel, double sideband passive microwave temperature sounder with cross-track scanning and will provide 18 km surface resolution from a 400 km orbit. The radiometer implements a two-point calibration using an internal PIN switch and view of cold space. Although the instrument is based on a well established classical design, the challenges lie in developing a sensitive spectrometer that fits in a 1.5U volume, is low cost, consumes 4 W power and satisfies the CubeSat weight and envelope constraints. PolarCube is scheduled for launch on a Virgin Galactic flight in summer, 2018. The estimated radiometer sensitivity, ΔTrms varies from 0.3 to 2 K across the eight channels. The 50 MHz to 7 GHz 8-channel filter bank (designed with surface mount capacitors and inductors) fits on a 9x5 cm2 RO4350B PCB and includes 2-stage amplification and detector circuitry. The scanning reflector with an 8 cm2 main aperture uses a 3D printed corrugated feed that includes a WR8 to WC8 waveguide transition with a 17° bend. Initial performance results from the instrument using the 3D printed feed and IF/VA board obtained from airborne measurements over Antarctica on the NASA DC8 in early November 2016 indicate a well-functioning radiometer. The end-to-end characterization of the payload with the satellite bus, performance results from vibration and thermal-vacuum tests and roof-top measurements will be presented.

Job strain and health-related lifestyle: findings from an individual-participant meta-analysis of 118,000 working adults.

Science.gov (United States)

Heikkilä, Katriina; Fransson, Eleonor I; Nyberg, Solja T; Zins, Marie; Westerlund, Hugo; Westerholm, Peter; Virtanen, Marianna; Vahtera, Jussi; Suominen, Sakari; Steptoe, Andrew; Salo, Paula; Pentti, Jaana; Oksanen, Tuula; Nordin, Maria; Marmot, Michael G; Lunau, Thorsten; Ladwig, Karl-Heinz; Koskenvuo, Markku; Knutsson, Anders; Kittel, France; Jöckel, Karl-Heinz; Goldberg, Marcel; Erbel, Raimund; Dragano, Nico; DeBacquer, Dirk; Clays, Els; Casini, Annalisa; Alfredsson, Lars; Ferrie, Jane E; Singh-Manoux, Archana; Batty, G David; Kivimäki, Mika

2013-11-01

We examined the associations of job strain, an indicator of work-related stress, with overall unhealthy and healthy lifestyles. We conducted a meta-analysis of individual-level data from 11 European studies (cross-sectional data: n = 118,701; longitudinal data: n = 43,971). We analyzed job strain as a set of binary (job strain vs no job strain) and categorical (high job strain, active job, passive job, and low job strain) variables. Factors used to define healthy and unhealthy lifestyles were body mass index, smoking, alcohol intake, and leisure-time physical activity. Individuals with job strain were more likely than those with no job strain to have 4 unhealthy lifestyle factors (odds ratio [OR] = 1.25; 95% confidence interval [CI] = 1.12, 1.39) and less likely to have 4 healthy lifestyle factors (OR = 0.89; 95% CI = 0.80, 0.99). The odds of adopting a healthy lifestyle during study follow-up were lower among individuals with high job strain than among those with low job strain (OR = 0.88; 95% CI = 0.81, 0.96). Work-related stress is associated with unhealthy lifestyles and the absence of stress is associated with healthy lifestyles, but longitudinal analyses suggest no straightforward cause-effect relationship between work-related stress and lifestyle.

Fabrication of Te and Te-Au Nanowires-Based Carbon Fiber Fabrics for Antibacterial Applications

Directory of Open Access Journals (Sweden)

Ting-Mao Chou

2016-02-01

Full Text Available Pathogenic bacteria that give rise to diseases every year remain a major health concern. In recent years, tellurium-based nanomaterials have been approved as new and efficient antibacterial agents. In this paper, we developed the approach to directly grow tellurium nanowires (Te NWs onto commercial carbon fiber fabrics and demonstrated their antibacterial activity. Those Te NWs can serve as templates and reducing agents for gold nanoparticles (Au NPs to deposit. Three different Te-Au NWs with varied concentration of Au NPs were synthesized and showed superior antibacterial activity and biocompability. These results indicate that the as-prepared carbon fiber fabrics with Te and Te-Au NWs can become antimicrobial clothing products in the near future.

Galvano-magnetic properties and Shubnikov de Haas effect of Te-whiskers

International Nuclear Information System (INIS)

Berezovets, Veacheslav; Bondarchuk, Nikolai; Nikolaeva, Albina; Nijankovskii, Victor

2009-01-01

The work is devoted to investigation of the peculiarities of magnetoresistance, Hall effect and Shubnikov de Haas oscillations in Te-whiskers. Te-whiskers was prepared from vapor-gas phase on the substrate pure tellurium and grown naturally, of the walls of a crucible in the course of growing Te single crystals by the Czochralski method . The measurements of the galvanomagnetic properties and Shubnikov de Haas oscillation correspond to the notion of the occurrence of the effect of intraband magnetic breakdown when two different quasi-classical cyclotron trajectories coexist simultaneously in a magnetic field. This effect is a consequence of the presence of the saddle point in the dispersion law of the tellurium valence band. (authors)

Flexible screen printed thick film thermoelectric generator with reduced material resistivity

International Nuclear Information System (INIS)

Cao, Z; Koukharenko, E; Torah, R N; Tudor, J; Beeby, S P

2014-01-01

This work presents a flexible thick-film Bismuth Tellurium/Antimony Tellurium (BiTe/SbTe) thermoelectric generator (TEG) with reduced material resistivity fabricated by screen printing technology. Cold isostatic pressing (CIP) was introduced to lower the resistivity of the printed thermoelectric materials. The Seebeck coefficient (α) and the resistivity (ρ) of printed materials were measured as a function of applied pressure. A prototype TEG with 8 thermocouples was fabricated on flexible polyimide substrate. The dimension of a single printed element was 20 mm × 2 mm × 78.4 pm. The coiled-up prototype produced a voltage of 36.4 mV and a maximum power of 40.3 nW from a temperature gradient of 20 °C

Non-destructive local determination of doping additions and main components in single crystals

International Nuclear Information System (INIS)

Ehksperiandova, L.P.; Blank, A.B.; Kukhtina, N.N.; Afanasiadi, L.I.

1994-01-01

Procedures for local non-destructive determination of elements in optical and scintillation single crystals are developed. They are applied for determination of the main components (in cadmium tungstate) and doping additions (tellurium in zinc selenide, europium in gadolinium silicate). The metrological characteristics of the developed micro-analysis methods are estimated. Segregation of the main components and doping additions in the objects under consideration are investigated. Tellurium is found to be distributed uniformly on the cross-sections of bulk zinc selenide single crystals. The segregation of europium along gadolinium silicate ingots is almost absent. On the cross-section surface of cadmium tungstate single crystals the microregions are found characterized by the prevailing contents of cadmium or tungsten

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow

On the thermoluminescence profile of an Ionian Sea sediment: evidence of 137, 118, 12.1 and 10.8y cycles in the last two millennia

International Nuclear Information System (INIS)

Cini Castagnoli, G.; Bonino, G.; Provenzale, A.

1988-01-01

The thermoluminescence profile of an Ionian Sea recent sedimentary core, constructed with 467 equispaced data points and spanning 18 centuries from 170 to 1974 A.D. is studied. Several time series analysis methods reveal two evident periodicities on the centennial time scale, at 137 years and 118 years, both with their second harmonics. Together with these slow cyclic variations two sharp periodicities appear on the decennial time scale, at 12.1 years and 10.8 years. In the present study the amplitude and phase of these waves have been determined and it is shown that their summation accounts for more than 50% of the standard deviation of the whole time series and that they correctly reproduce the basic characteristics of the data

Sorption of V and VI group metalloids (As, Sb, Te on modified peat sorbents

Directory of Open Access Journals (Sweden)

Ansone-Bertina Linda

2016-01-01

Full Text Available The present work investigates arsenic, antimony and tellurium sorption using iron modified peat. The results were obtained using batch tests and the sorption was studied as a function of initial metalloid concentration, pH and sorption time, as well as the presence of competing substances. The obtained results indicate that modification of peat with Fe compounds significantly enhances the sorption capacity of the sorbents used for sorption of arsenic, antimony and tellurium. The optimal pH interval for the sorption of Sb(III is 6.5–9 and for As(V and Sb(V – 3–6, while As(III and tellurium sorption using Fe-modified peat is favourable in a wider interval of 3–9. The presence of competing ions as well as HA affect sorption of metalloids on Fe-modified peat. A minor impact on the reduction of metalloid sorption was detected in the presence of nitrate, sulphate, carbonate and tartrate ions, while in the presence of phosphate and HA the sorption ability of metalloids can be considerably reduced. The obtained results of kinetic experiments indicate that sorption of metalloids on Fe-modified peat mainly occurs relying on mechanisms of physical sorption processes.

Clinical Characteristics of 118 Cases of Chronic Obstructive Pulmonary Disease Complicated with Primary Bronchopulmonary Carcinoma

Directory of Open Access Journals (Sweden)

Songlin ZHAO

2017-08-01

Full Text Available Background and objective The aim of this study is to investigate the clinical characteristics of patients with primary bronchopulmonary carcinoma complicated with chronic obstructive pulmonary disease (COPD, and to optimize the early diagnoses in the coexistence of COPD and primary bronchopulmonary carcinoma. Methods The clinical data of 118 patients with COPD complicated with primary bronchopulmonary carcinoma were analyzed retrospectively, including age, sex, smoking history, smoking index, clinical symptoms and signs, pathological type, staging, metastasis site and lung function index. 120 patients with simple COPD were selected as control. Results The smoking rate (55.1% and smoking index ≥400 branch /year (90.8% of the patients with COPD complicated with primary bronchopulmonary carcinoma were higher than the simple COPD group (20.8%, 48.0%. The difference between the two groups was statistically significant (P0.05, while the incidence of hemoptysis, weight loss, chest pain, hoarseness, pleural effusion and atelectasis were significantly higher than those in simple COPD group (P0.05, but the diffusing capacity of carbon monoxide (DLCO of COPD patients complicated with primary bronchopulmonary carcinoma was lower than that of simple COPD patients (P<0.05 . In the COPD patients with primary bronchopulmonary carcinoma, squamous cell carcinoma was the most common pathological type (51.7%. Male patients were mainly squamous cell carcinoma (60.7%, while female patients with adenocarcinoma (69.0%. Conclusion COPD combined with primary bronchopulmonary carcinoma occurs in male smokers more. There is higher incidence of squamous cell carcinoma. When they are first diagnosed, most of them are advanced or located late, due to no specific clinical symptoms at the early stages. Periodic chest CT examination for COPD patients can help early diagnoses of primary bronchopulmonary carcinoma.

Characterization of alpha low level waste in 118 litre drums by passive and active neutron measurements in the promethee assay system

International Nuclear Information System (INIS)

Jallu, F.; Passard, C.; Mariani, A.; Ma, J.L.; Baudry, G.; Romeyer-Dherbey, J.; Recroix, H.; Rodriguez, M.; Loridon, J.; Denis, C.; Toubon, H.

2003-01-01

This paper deals with the PROMETHEE (PROMpt, epithermal and THErmal interrogation experiment) waste assay system for alpha low level waste (LLW) characterization. This device, including both passive and active neutron measurement methods, is developed at the French Atomic Energy Commission (C.E.A.), Cadarache Centre, in cooperation with COGEMA. Its purpose is to reach the requirements for incinerating alpha waste (less than 50 Bq[α], i.e. about 50 μg of Pu per gram of raw waste) in 118 litre- > drums. The PROMETHEE development and progress are performed with the help of simulation based on the Monte Carlo code MCNP4 [1]. These calculations are coupled with specific experiments in order to confirm calculated results and to obtain characteristics that can not be approached by the simulation (background for example). This paper presents the PROMETHEE measurement cell, its current performances, and studies performed at the laboratory about the most limiting parameters such as the matrix of the drum - its composition (H, Cl..), its density and its heterogeneity degree -the localization and the self-shielding properties of the contaminant. (orig.)

Characterization of alpha low level waste in 118 litre drums by passive and active neutron measurements in the promethee assay system

Energy Technology Data Exchange (ETDEWEB)

Jallu, F.; Passard, C.; Mariani, A.; Ma, J.L.; Baudry, G.; Romeyer-Dherbey, J.; Recroix, H.; Rodriguez, M.; Loridon, J.; Denis, C. [French Atomic Energy Commission (C.E.A./Cadarache), DED/SCCD/LDMN, Durance (France); Toubon, H. [COGEMA, VELIZY-VILLACOUBLAY (France)

2003-07-01

This paper deals with the PROMETHEE (PROMpt, epithermal and THErmal interrogation experiment) waste assay system for alpha low level waste (LLW) characterization. This device, including both passive and active neutron measurement methods, is developed at the French Atomic Energy Commission (C.E.A.), Cadarache Centre, in cooperation with COGEMA. Its purpose is to reach the requirements for incinerating alpha waste (less than 50 Bq[{alpha}], i.e. about 50 {mu}g of Pu per gram of raw waste) in 118 litre-<> drums. The PROMETHEE development and progress are performed with the help of simulation based on the Monte Carlo code MCNP4 [1]. These calculations are coupled with specific experiments in order to confirm calculated results and to obtain characteristics that can not be approached by the simulation (background for example). This paper presents the PROMETHEE measurement cell, its current performances, and studies performed at the laboratory about the most limiting parameters such as the matrix of the drum - its composition (H, Cl..), its density and its heterogeneity degree -the localization and the self-shielding properties of the contaminant. (orig.)

Structural and Optothermal Properties of Iron Ditelluride Layered Structures in the Framework of the Lattice Compatibility Theory

Directory of Open Access Journals (Sweden)

K. Ben Messaoud

2014-01-01

Full Text Available This study concerns structural and optothermal properties of iron ditelluride layered structures which were fabricated via a low-cost protocol. The main precursors were FeCl3 · 6H2O and Fe2O3. After a heat treatment within a tellurium-rich medium at various temperatures (470°C, 500°C, and 530°C during 24 h, classical analyses have been applied to the iron ditelluride layered structures. A good crystalline state with a preferential orientation of the crystallites along (111 direction has been recorded. Moreover, additional opto-thermal investigation and analyses within the framework of the Lattice Compatibility Theory gave plausible explanation for prompt temperature-dependent incorporation of tellurium element inside hematite elaborated matrices.

Anomalous behavior of tellurium abundances

Energy Technology Data Exchange (ETDEWEB)

Cohen, B L

1984-01-01

The cosmic abundance of Te is larger than for any element with atomic number greater than 40, but it is one of the least abundant elements in the earth's lithosphere and it is one of the five elements never reported in sea water. On the other hand, it is the fourth most abundant element in the human body (after Fe, Zn and Rb), and is unusually abundant in human food. It is shown that the high abundance in human food combined with the low abundance in soil requires that it be picked up by plant roots very much more efficiently than any other trace element.

Heat-Transfer and Pressure Measurements from a Flight Test of the Third 1/18-Scale Model of the Titan Intercontinental Ballistic Missile up to a Mach Number of 3.86 and Reynolds Number per Foot of 23.5 x 10(exp 6) and a Comparison with Heat Transfer

Science.gov (United States)

Graham, John B., Jr.

1958-01-01

Heat-transfer and pressure measurements were obtained from a flight test of a 1/18-scale model of the Titan intercontinental ballistic missile up to a Mach number of 3.86 and Reynolds number per foot of 23.5 x 10(exp 6) and are compared with the data of two previously tested 1/18-scale models. Boundary-layer transition was observed on the nose of the model. Van Driest's theory predicted heat-transfer coefficients reasonably well for the fully laminar flow but predictions made by Van Driest's theory for turbulent flow were considerably higher than the measurements when the skin was being heated. Comparison with the flight test of two similar models shows fair repeatability of the measurements for fully laminar or turbulent flow.

Resonant ionization by laser beams: application to ions sources and to study the nuclear structure of radioactive tellurium isotopes; Ionisation resonante par faisceaux laser: application aux sources d'ions et a l'etude de la structure des noyaux radioactifs de tellure

Energy Technology Data Exchange (ETDEWEB)

Sifi, R

2007-07-15

The radioactive ion beams that are produced through current isotope separators are well separated according to the A mass but not according to the Z parameter. The resonant ionization through laser beams applied to ion sources allows the production of radioactive ion beam in a very selective and efficient way by eliminating the isobaric contamination. The first chapter is dedicated to the resonant ionization by laser beams, we describe the principle, the experimental setting, the lasers used, the ionization schemes and the domain of application. The second chapter deals with the application of resonant ionization to laser ion sources for the production of radioactive ion beams. We present experimental tests performed for getting copper ion beams. Resonant ionization through laser is also used in the spectroscopy experiments performed at the Isolde (isotope separation on-line device) installation in CERN where more than 20 elements are ionized very efficiently. The technique is based on a frequency scanning around the excitation transition of the atoms in order to probe the hyperfine structure. Laser spectroscopy allows the determination of the hyperfine structure as well as the isotopic shift of atoms. In the third chapter the method is applied to the spectroscopy of tellurium atoms. First, we define the 2 parameters on which the extraction is based: charge radius and nuclear moments, then we present several theoretical models that we have used to assess our experimental results. (A.C.)

Opioid Antagonists and the A118G Polymorphism in the μ-Opioid Receptor Gene: Effects of GSK1521498 and Naltrexone in Healthy Drinkers Stratified by OPRM1 Genotype

Science.gov (United States)

Ziauddeen, Hisham; Nestor, Liam J; Subramaniam, Naresh; Dodds, Chris; Nathan, Pradeep J; Miller, Sam R; Sarai, Bhopinder K; Maltby, Kay; Fernando, Disala; Warren, Liling; Hosking, Louise K; Waterworth, Dawn; Korzeniowska, Anna; Win, Beta; Richards, Duncan B; Vasist Johnson, Lakshmi; Fletcher, Paul C; Bullmore, Edward T

2016-01-01

The A118G single-nucleotide polymorphism (SNP rs1799971) in the μ-opioid receptor gene, OPRM1, has been much studied in relation to alcohol use disorders. The reported effects of allelic variation at this SNP on alcohol-related behaviors, and on opioid receptor antagonist treatments, have been inconsistent. We investigated the pharmacogenetic interaction between A118G variation and the effects of two μ-opioid receptor antagonists in a clinical lab setting. Fifty-six overweight and moderate–heavy drinkers were prospectively stratified by genotype (29 AA homozygotes, 27 carriers of at least 1 G allele) in a double-blind placebo-controlled, three-period crossover design with naltrexone (NTX; 25 mg OD for 2 days, then 50 mg OD for 3 days) and GSK1521498 (10 mg OD for 5 days). The primary end point was regional brain activation by the contrast between alcohol and neutral tastes measured using functional magnetic resonance imaging (fMRI). Secondary end points included other fMRI contrasts, subjective responses to intravenous alcohol challenge, and food intake. GSK1521498 (but not NTX) significantly attenuated fMRI activation by appetitive tastes in the midbrain and amygdala. GSK1521498 (and NTX to a lesser extent) significantly affected self-reported responses to alcohol infusion. Both drugs reduced food intake. Across all end points, there was less robust evidence for significant effects of OPRM1 allelic variation, or for pharmacogenetic interactions between genotype and drug treatment. These results do not support strong modulatory effects of OPRM1 genetic variation on opioid receptor antagonist attenuation of alcohol- and food-related behaviors. However, they do support further investigation of GSK1521498 as a potential therapeutic for alcohol use and eating disorders. PMID:27109624

Purification and in vitro antioxidant activities of tellurium-containing phycobiliproteins from tellurium-enriched Spirulina platensis

OpenAIRE

Chen, Tianfeng; Yang,Fang; Wong,Ka-Hing; Yang,Yufeng; Li,Xiaoling; Jiang,Jie; Wu,Hualian; Zheng,Wenjie

2014-01-01

Fang Yang,1 Ka-Hing Wong,2 Yufeng Yang,3 Xiaoling Li,1 Jie Jiang,1 Wenjie Zheng,1 Hualian Wu,1 Tianfeng Chen1 1Department of Chemistry, Jinan University, Guangzhou, People’s Republic of China; 2Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hong Kong, People’s Republic of China; 3Institute of Hydrobiology, College of Life Science and Technology, Jinan University, Guangzhou, People’s Republic of China Abstract: Tellu...

Job Strain and Health-Related Lifestyle: Findings From an Individual-Participant Meta-Analysis of 118 000 Working Adults

Science.gov (United States)

Heikkilä, Katriina; Fransson, Eleonor I.; Nyberg, Solja T.; Zins, Marie; Westerlund, Hugo; Westerholm, Peter; Virtanen, Marianna; Vahtera, Jussi; Suominen, Sakari; Steptoe, Andrew; Salo, Paula; Pentti, Jaana; Oksanen, Tuula; Nordin, Maria; Marmot, Michael G.; Lunau, Thorsten; Ladwig, Karl-Heinz; Koskenvuo, Markku; Knutsson, Anders; Kittel, France; Jöckel, Karl-Heinz; Goldberg, Marcel; Erbel, Raimund; Dragano, Nico; DeBacquer, Dirk; Clays, Els; Casini, Annalisa; Alfredsson, Lars; Ferrie, Jane E.; Singh-Manoux, Archana; Batty, G. David; Kivimäki, Mika

2013-01-01

Objectives. We examined the associations of job strain, an indicator of work-related stress, with overall unhealthy and healthy lifestyles. Methods. We conducted a meta-analysis of individual-level data from 11 European studies (cross-sectional data: n = 118 701; longitudinal data: n = 43 971). We analyzed job strain as a set of binary (job strain vs no job strain) and categorical (high job strain, active job, passive job, and low job strain) variables. Factors used to define healthy and unhealthy lifestyles were body mass index, smoking, alcohol intake, and leisure-time physical activity. Results. Individuals with job strain were more likely than those with no job strain to have 4 unhealthy lifestyle factors (odds ratio [OR] = 1.25; 95% confidence interval [CI] = 1.12, 1.39) and less likely to have 4 healthy lifestyle factors (OR = 0.89; 95% CI = 0.80, 0.99). The odds of adopting a healthy lifestyle during study follow-up were lower among individuals with high job strain than among those with low job strain (OR = 0.88; 95% CI = 0.81, 0.96). Conclusions. Work-related stress is associated with unhealthy lifestyles and the absence of stress is associated with healthy lifestyles, but longitudinal analyses suggest no straightforward cause–effect relationship between work-related stress and lifestyle. PMID:23678931

Proceedings 43rd Stanford Geothermal Workshop

Energy Technology Data Exchange (ETDEWEB)

Simmons, Stuart; Kirby, Stefan; Verplanck, Philip; Kelley, Karen

2018-02-12

Herein we summarize the results of an investigation dealing with the concentrations and inventories of strategic, critical and valuable materials (SCVM) in produced fluids from geothermal and hydrocarbon reservoirs (50-250° C) in Nevada and Utah. Water samples were collected from thirty-four production wells across eight geothermal fields, the Uinta Basin oil/gas province in northeast Utah, and the Covenant oil field in southwestern Utah; additional water samples were collected from six hot springs in the Sevier Thermal Belt in southwestern Utah. Most SCVM concentrations in produced waters range from <0.1 to 100 µg/kg; the main exception is lithium, which has concentrations that range from <1000 to 25,000 ug/kg. Relatively high concentrations of gallium, germanium, scandium, selenium, and tellurium are measured too. Geothermal waters contain very low concentrations of REEs, below analytical detections limits (0.01 µg/kg), but the concentrations of lanthanum, cerium, and europium range from 0.05 to 5 µg/kg in Uinta basin waters. Among the geothermal fields, the Roosevelt Hot Spring reservoir appears to have the largest inventories of germanium and lithium, and Patua appears to have the largest inventories of gallium, scandium, selenium, and tellurium. By comparison, the Uinta basin has larger inventories of gallium. The concentrations of gallium, germanium, lithium, scandium, selenium, and tellurium in produced waters appear to be partly related to reservoir temperature and concentrations of total dissolved salts. The relatively high concentration and large inventory of lithium occurring at Roosevelt Hot Springs may be related to granitic-gneissic crystalline rocks, which host the reservoir. Analyses of calcite scales from Dixie Valley indicate enrichments in cobalt, gallium, gold, palladium, selenium and tellurium, and these metals appear to be depositing at deep levels in production wells due to boiling. Comparisons with SCVM mineral deposits suggest that

Electrochemical Deposition of CdTe Semiconductor Thin Films for Solar Cell Application Using Two-Electrode and Three-Electrode Configurations: A Comparative Study

Directory of Open Access Journals (Sweden)

O. K. Echendu

2016-01-01

Full Text Available Thin films of CdTe semiconductor were electrochemically deposited using two-electrode and three-electrode configurations in potentiostatic mode for comparison. Cadmium sulphate and tellurium dioxide were used as cadmium and tellurium sources, respectively. The layers obtained using both configurations exhibit similar structural, optical, and electrical properties with no specific dependence on any particular electrode configuration used. These results indicate that electrochemical deposition (electrodeposition of CdTe and semiconductors in general can equally be carried out using two-electrode system as well as the conventional three-electrode system without compromising the essential qualities of the materials produced. The results also highlight the advantages of the two-electrode configuration in process simplification, cost reduction, and removal of a possible impurity source in the growth system, especially as the reference electrode ages.

Charge transport properties of CdMnTe radiation detectors

Energy Technology Data Exchange (ETDEWEB)

Kim K.; Rafiel, R.; Boardman, M.; Reinhard, I.; Sarbutt, A.; Watt, G.; Watt, C.; Uxa, S.; Prokopovich, D.A.; Belas, E.; Bolotnikov, A.E.; James, R.B.

2012-04-11

Growth, fabrication and characterization of indium-doped cadmium manganese telluride (CdMnTe)radiation detectors have been described. Alpha-particle spectroscopy measurements and time resolved current transient measurements have yielded an average charge collection efficiency approaching 100 %. Spatially resolved charge collection efficiency maps have been produced for a range of detector bias voltages. Inhomogeneities in the charge transport of the CdMnTe crystals have been associated with chains of tellurium inclusions within the detector bulk. Further, it has been shown that the role of tellurium inclusions in degrading chargecollection is reduced with increasing values of bias voltage. The electron transit time was determined from time of flight measurements. From the dependence of drift velocity on applied electric field the electron mobility was found to be n = (718 55) cm2/Vs at room temperature.

Control of interferences in the analysis of low-concentration I 129

International Nuclear Information System (INIS)

Quintana, Eduardo E.; Thyssen, Sandra M.

1999-01-01

Traces of uranium, cesium and tellurium interfere in the determination of I 129 by neutron activation analysis. The paper describes the procedures used to control or eliminate the interferences in the different steps of the analysis

Investigating body function

International Nuclear Information System (INIS)

Monks, R.; Riley, A.L.M.

1981-01-01

This invention relates to the investigation of body function, especially small bowel function but also liver function, using bile acids and bile salts or their metabolic precursors labelled with radio isotopes and selenium or tellurium. (author)

Comparative study on the bioactivation mechanisms and cytotoxicity of Te-phenyl-L-tellurocysteine, Se-phenyl-L-selenocysteine, and S-phenyl-L-cysteine

NARCIS (Netherlands)

Rooseboom, Martijn; Vermeulen, Nico P E; Durgut, Fatma; Commandeur, Jan N M

2002-01-01

Tellurium compounds are effective antioxidants and chemoprotectors, even more active than their selenium and sulfur analogues. In addition to these properties, some selenium compounds, such as selenocysteine Se-conjugates, possess significant chemopreventive and antitumor activities, and selenol

Structure effects in the region of superheavy elements via the alpha-decay chain of sup 2 sup 9 sup 3 118

CERN Document Server

Gupta, R K; Kumar, R; Balasubramaniam, M; Scheid, W

2002-01-01

The alpha-decay chain of sup 2 sup 9 sup 3 118, first proposed in the Berkeley cold fusion experiment sup 2 sup 0 sup 8 Pb( sup 8 sup 6 Kr, 1n) and now retracted, is calculated by using the preformed cluster model (PCM) of one of the authors (RKG). Also, the possible branchings of alpha-decays to heavier cluster decays of all the parents in this chain are calculated for the first time. The calculated Q-values, penetrabilities and preformation factors for alpha-decays suggest that the sup 2 sup 8 sup 5 114 nucleus with Z=114, N=171 is a magic nucleus, either due to the magicity of Z=114, or N=172 or both. The N=172 is proposed to be a magic number in certain relativistic mean-field calculations, but with Z 120. The calculated cluster decays point to new interesting possibilities of sup 1 sup 4 C decay of the sup 2 sup 8 sup 1 112 parent, giving rise to a (reasonably) deformed Z=106, N=161, sup 2 sup 6 sup 7 106 daughter (N=162 being now established as the deformed magic shell) or to a doubly magic sup 4 sup 8 ...

Comparison of Se and Te clusters produced by ion bombardment

Directory of Open Access Journals (Sweden)

Trzyna Małgorzata

2017-01-01

Full Text Available Nanostructures based on tellurium and selenium are materials used as components for the manufacturing topological insulators. Therefore it is crucial to precisely characterize these materials. In this work the emission of selenium and tellurium cluster ions, sputtered by Bi+ primary ion guns, was investigated by using Time-of-Flight Secondary Ion Mass Spectrometry (TOF SIMS. It has been found that BixTex and BixSex clusters appear in addition to Sex and Tex clusters in the mass range up to ~ 1300 m/z. Local maxima or minima (magic numbers are observed in the ion intensity versus a number of atoms per cluster for both positive and negative ions spectra for all types of clusters and primary ions used. These extrema can be attributed to different yield and stability of certain clusters but also to fragmentation of high-mass clusters.

Heavily doped GaAs:Te layers grown by MOVPE using diisopropyl telluride as a source

Energy Technology Data Exchange (ETDEWEB)

Daniltsev, V. M.; Demidov, E. V.; Drozdov, M. N.; Drozdov, Yu. N., E-mail: drozdyu@ipmras.ru; Kraev, S. A.; Surovegina, E. A.; Shashkin, V. I.; Yunin, P. A. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation)

2016-11-15

The capabilities of GaAs epitaxial layers extremely heavily doped with tellurium by metal-organic vapor-phase epitaxy using diisopropyl telluride as a source are studied. It is shown that tellurium incorporation into GaAs occurs to an atomic concentration of 10{sup 21} cm{sup –3} without appreciable diffusion and segregation effects. Good carrier concentrations (2 × 10{sup 19} cm{sup –3}) and specific contact resistances of non-alloyed ohmic contacts (1.7 × 10{sup –6} Ω cm{sup 2}) give grounds to use such layers to create non-alloyed ohmic contacts in electronic devices. A sharp decrease in the electrical activity of Te atoms, a decrease in the electron mobility, and an increase in the contact resistance at atomic concentrations above 2 × 10{sup 20} cm{sup –3} are detected.

Systems and methods for the synthesis of high thermoelectric performance doped-SnTe materials

Science.gov (United States)

Ren, Zhifeng; Zhang, Qian; Chen, Gang

2018-02-27

A thermoelectric composition comprising tin (Sn), tellurium (Te) and at least one dopant that comprises a peak dimensionless figure of merit (ZT) of 1.1 and a Seebeck coefficient of at least 50 .mu.V/K and a method of manufacturing the thermoelectric composition. A plurality of components are disposed in a ball-milling vessel, wherein the plurality of components comprise tin (Sn), tellurium (Te), and at least one dopant such as indium (In). The components are subsequently mechanically and thermally processed, for example, by hot-pressing. In response to the mechanical-thermally processing, a thermoelectric composition is formed, wherein the thermoelectric composition comprises a dimensionless figure of merit (ZT) of the thermoelectric composition is at least 0.8, and wherein a Seebeck coefficient of the thermoelectric composition is at least 50 .mu.V/K at any temperature.

Calculation of 125Te NMR Chemical Shifts at the Full Four-Component Relativistic Level with Taking into Account Solvent and Vibrational Corrections: A Gateway to Better Agreement with Experiment.

Science.gov (United States)

Rusakova, Irina L; Rusakov, Yuriy Yu; Krivdin, Leonid B

2017-06-29

Four-component relativistic calculations of 125 Te NMR chemical shifts were performed in the series of 13 organotellurium compounds, potential precursors of the biologically active species, at the density functional theory level under the nonrelativistic and four-component fully relativistic conditions using locally dense basis set scheme derived from relativistic Dyall's basis sets. The relativistic effects in tellurium chemical shifts were found to be of as much as 20-25% of the total calculated values. The vibrational and solvent corrections to 125 Te NMR chemical shifts are about, accordingly, 6 and 8% of their total values. The PBE0 exchange-correlation functional turned out to give the best agreement of calculated tellurium shifts with their experimental values giving the mean absolute percentage error of 4% in the range of ∼1000 ppm, provided all corrections are taken into account.

Specific features of phase transformations in germanium monotelluride

International Nuclear Information System (INIS)

Bigvava, A.D.; Gabedava, A.A.; Kunchuliya, Eh.D.; Shvangiradze, R.R.

1981-01-01

Phase transformations in germanium monotelluride are studied . using DRON-0.5 and DRON-1 plants with high-temperature chamber GPVT-1500 at Cu, Ksub(α) radiation. It is shown that in the whole homogeneity range α GeTe is a metastable phase which is formed under the conditions of fast cooling of alloy from temperatures >=Tsub(cub) (temperature of transition in cubic crystal system). An equilibrium γ-phase is obtained by annealing of dispersed powders and metal-ceramic specimens of alloys with 50.3; 50.6; 50.9 at % Te. Lattice parameters of rhombic γ-phase do not depend on tellurium content in initial α- phase. α→γ transformation is observed at any temperature less than Tsub(cub) with the change of alloy composition, namely tellurium precipitation. γ-phase transforms into β at higher temperatures than α-phase [ru

Comparison of Se and Te clusters produced by ion bombardment

Science.gov (United States)

Trzyna, Małgorzata

2017-01-01

Nanostructures based on tellurium and selenium are materials used as components for the manufacturing topological insulators. Therefore it is crucial to precisely characterize these materials. In this work the emission of selenium and tellurium cluster ions, sputtered by Bi+ primary ion guns, was investigated by using Time-of-Flight Secondary Ion Mass Spectrometry (TOF SIMS). It has been found that BixTex and BixSex clusters appear in addition to Sex and Tex clusters in the mass range up to 1300 m/z. Local maxima or minima (magic numbers) are observed in the ion intensity versus a number of atoms per cluster for both positive and negative ions spectra for all types of clusters and primary ions used. These extrema can be attributed to different yield and stability of certain clusters but also to fragmentation of high-mass clusters.

The Effects of the WNT-Signaling Modulators BIO and PKF118-310 on the Chondrogenic Differentiation of Human Mesenchymal Stem Cells.

Science.gov (United States)

Huang, Xiaobin; Zhong, Leilei; Hendriks, Jan; Post, Janine N; Karperien, Marcel

2018-02-13

Mesenchymal stem cells (MSCs) are multipotent cells, mainly from bone marrow, and an ideal source of cells in bone and cartilage tissue engineering. A study of the chondrogenic differentiation of MSCs is of particular interest for MSCs-based cartilage regeneration. In this study, we aimed to optimize the conditions for the chrondogenic differentiation of MSCs by regulating WNT signaling using the small molecule WNT inhibitor PKF118-310 and activator BIO. Human mesenchymal stem cells (hMSCs) were isolated from bone marrow aspirates and cultured in hMSCs proliferation medium. Pellet culture was subsequently established for three-dimensional chondrogenic differentiation of 5 weeks. WNT signaling was increased by the small molecule glycogen synthase kinase-3 inhibitor 6-bromoindirubin-3-oxim (BIO) and decreased by the WNT inhibitor PKF118-310 (PKF). The effects of BIO and PKF on the chondrogenesis of hMSCs was examined by real-time PCR, histological methods, and ELISA. We found that activation of canonical WNT-signaling by BIO significantly downregulated the expression of cartilage-specific genes SOX9 , COL2A1, and ACAN , and matrix metalloproteinase genes MMP1/3/9/13, but increased ADAMTS 4/5 . Inhibition of WNT signaling by PKF increased the expression of SOX9 , COL2A1 , ACAN , and MMP9, but decreased MMP13 and ADAMTS4/5 . In addition, a high level of WNT signaling induced the expression of hypertrophic markers COL10A1, ALPL , and RUNX2, the dedifferentiation marker COL1A1 , and glycolysis genes GULT1 and PGK1 . Deposition of glycosaminoglycan (GAG) and collagen type II in the pellet matrix was significantly lost in the BIO-treated group and increased in the PKF-treated group. The protein level of COL10A1 was also highly induced in the BIO group. Interestingly, BIO decreased the number of apoptotic cells while PKF significantly induced apoptosis during chondrogenesis. The natural WNT antagonist DKK1 and the protein level of MMP1 in the pellet culture medium were