WorldWideScience

Sample records for teiryo hyoka gijutsu

  1. Primary study on quantitative evaluation of driver fatigue; Unten hiro no teiryo hyoka gijutsu ni kansuru kiso kento

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, Y; Mochizuki, M; Toyofuku, K [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Katsuura, T [Chiba University, Chiba (Japan)

    1997-10-01

    Quantitative evaluation of physical and mental loads are effective in developing more human-friendly vehicles. Here attention has been focused on the mental load. Attempts were made to find some physiological indices that can be used for quantifying the mental load and resultant fatigue. Subjects were told to perform three different tasks in a climatoron, and the relation between physiological indices and their perception of fatigue as well as their capability of performing the tasks were analyzed. As a result, heart rate variability is a good index for quantitative evaluation of mental load and fatigue. 5 refs., 4 figs., 6 tabs.

  2. Report on the evaluation of the development of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy; Denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An objective evaluation from a third party was conducted on the purpose, plan, execution method, achievement, etc. of a project 'The devilment of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy.' The purpose of the project is to make the relationing possible between the analytical results of the catalyst surface and the catalyst performance which has been so far difficult by heightening the accuracy of the catalyst quantitative surface analytical accuracy using the electron spectroscopy. The purpose and significance are judged to be worth a lot. This project is an industry/university/government joint project between the two countries. The project is excellent both in connection among research institutes and leadership of chief researchers, and it is judged that the joint research system fully functioned. The term of the project was shortened from 3 years in the first plan to 2 years, and therefore, the study was finished only on silicon oxide and organic thin films. However, it was determined that the study results are to be run in the magazine 'Surface and Interface Analysis,' which indicates that the achievement was judged to be very worth in the academic viewpoint. (NEDO)

  3. Evaluation technology of clothing comfortableness; Ifuku tekigosei hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Niwaya, H.

    1999-10-26

    Modern apparel industries are required to supply many kinds of products corresponding to various needs of consumers. Among consumers' needs, comfortableness to wear such as size-fitness is primarily important. To facilitate apparel industries, it is expected to develop a new technology of pattern designing of comfortable garment and measuring garment pressure distribution. Our research is aimed at developing technology that uses computer simulation to predict and evaluate wear comfort, including size suitability, without the need to actually sew up a garment. First, we developed a basic system to predict wearing silhouette, garment pressure, and ease looseness of the garment. Using this system, we carried on the following study. The 3-dimensional distributions of the garment pressure and ease looseness were reversely mapped on the paper pattern in order to indicate the preferable modification. The system was extended for several poses, e.g. twist, bend. From various parameters, we examined the factors of garment pressure and ease looseness. In addition, we selected the parameters for the size-fit indicators and investigated size-fit evaluation indicators. (author)

  4. Evaluation technology of human behavior cognition; Ningen kodo ninchi hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For human engineering and improvement of the living environment, the evaluation technology of human behavior cognition was studied. For the future reformation and creation of economic structure, the following are required: establishment of safe and affluent communities, further improvement of the safety and harmonious balance of people, lives and society, and R & D close to people and social needs. Introduction of Product Liability law and a fail-safe concept are examples of such efforts. However, since many accidents are found in the human society, the relation between human errors and human characteristics should be studied in detail. The cognitive science of human behavior is an objective evaluation technology from the viewpoint of human being, object, environment and society. Based on these social and technological background, the feasibility of the evaluation technology is studied, and the future trend and skeleton of this project are clarified. The domestic and foreign trends of technologies concerned are thus surveyed, and the important points, features, skeleton and ripple effect of the technology are summarized. 500 refs., 70 figs., 5 tabs.

  5. Fiscal 1998 development report on the high-accuracy quantitative analysis technique of catalyst surfaces by electron spectroscopy; 1998 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development of the high-accuracy quantitative analysis technique by electron spectroscopy for surface analysis of catalysts and semiconductors. Since conventional analysis technique using an energy-fixed X-ray excitation source is inadequate to obtain satisfactory surface sensitivity and quantitative accuracy for catalysts, for development of the titled technique, this project makes experiment using energy-variable synchrotron radiation to modify the parameter on motion of low-speed electrons in solids which is obtained by Monte Carlo calculation. For establishment of the high-accuracy quantitative analysis technique of surface compositions of materials such as catalyst of which performance is dominated by utmost surface, the project studies the attenuation length of electrons in solids by electron spectroscopy using soft X-rays from synchrotron radiation. In this fiscal year, the project established the equipment and technique for high-accuracy quantitative analysis of the thickness and electron attenuation length of silicon oxide films on silicon wafers by electron spectroscopy. (NEDO)

  6. Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

  7. Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

  8. Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

  9. Study of evaluation for grouting effect in a borehole; Yakueki chunyu koka hyoka gijutsu ni okeru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, H; Matsuo, T [Fukuoka Municipal Transportation Bureau, Fukuoka (Japan); Yamauchi, Y; Imanishi, H [Osaka Soil Test, Osaka (Japan)

    1996-10-01

    For the foundation improvement works by grouting in a borehole, evaluation of grouting effect is one of the most important management items. The grouting design and works are sometimes reconsidered depending on the evaluation of grouting effect during the test injection. The purpose of the evaluation of grouting effect is to grasp the range of improvement and consolidation after the injection, and to judge and estimate the strength and permeability of the consolidation part. This paper describes the judgment method of the strength using PS logging results and borehole televiewer (BHTV) logging results. The reflection intensity (Ir) by the BHTV logging increased after the grouting, which showed a same tendency as that using S-wave and P-wave velocities (Vs and Vp) before and after the grouting. This was considered to demonstrate the grouting effect. A relation was obtained between the Vs, Vp and Ir before and after the grouting, which was expressed by following equation. Ir=0.143{times}Vs-70=0.093{times}Vp-110. The relation with the dynamic elastic coefficient (Ed) was also obtained as follow; Ir=0.0013{times}Ed. 9 figs.

  10. Leading research in FY 1995. Research of product evaluation and advanced measurements - Part 1 (product evaluation); 1995 nendo sendo kenkyu. Seihin hyoka kodo keisoku bunseki gijutsu ni kansuru chosa kenkyu - 1 (seihin hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Product evaluation has been investigated from a viewpoint of compatibility with human life by considering human being as the subject of life. This report describes the investigation results. Product evaluation is defined as evaluating products on a consumer-oriented viewpoint and informing consumers of the evaluation results. According to a questionnaire survey with regard to daily living products, products in the low degree of satisfaction in their usage were electric tooth brush, video camera, electric rice jar, vacuum cleaner, and electric iron. Contents of dissatisfaction with these products were classified by aspect, i.e., human aspect regarding human body/recognition, life aspect regarding functions of products and how to use them, and sensitivity aspect such as appearance of products. Thus, points at issue were clarified. As regards the human aspect, incompatibility between the size/form of products and human body/posture, and recognition psychological incompatibility such as difficulty in understanding function or operation of products were pointed out. Establishment of a method for measuring and evaluating the human`s body functions and the compatibility with products, and necessity of the acquisition of human`s body characteristic data and the consolidation positions are also described. 4 refs., 42 figs., 30 tabs.

  11. Research and development of evaluation system for photovoltaic power generation system. Research and development of evaluation systems for photovoltaic cells and modules; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation system for solar cells in fiscal 1994. (1) On development of the performance evaluation method for solar cells, data collection, analysis and measurement of atmospheric conditions necessary for outdoor measurement were carried out to improve the measurement accuracy of laminated solar cells. The validity of measurement methods was verified by comparing experimental results with outdoor measurement ones to improve the indoor measurement accuracy by multiple light source solar simulator. Generated energy in solar cell module level was also studied in field. (2) On development of the reliability evaluation method for solar cells, deterioration data were collected and analyzed by long-term exposure test. As a result, it was clarified that Pmax values are directly affected by seasonal change in air mass, and deterioration of solar cells is hardly found after exposure test for one year, showing a stable state. The characteristic recovery experiment of amorphous solar cell modules was carried out, and the accelerated deterioration test method of thin film cell modules was also studied. 2 figs.

  12. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  13. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is conducted for the acquisition of a system evaluation technique for predicting the performance of standard photovoltaic power systems and evaluation technologies applicable to residential photovoltaic power systems different from each other in terms of tilt and direction, district, solar cell type, etc. In fiscal 1999, using data collected from the Hamamatsu field test facilities and residential photovoltaic power systems installed across Japan, various design parameters, such as the irregularity compensation coefficient, temperature compensation coefficient, and the incidence compensation coefficient were determined, and, using the parameters as the secondary estimation values, design parameters were updated. In the development of simulation technologies, basic studies were made about the shadow compensation coefficient, spectral response fluctuation compensation coefficient, and the composition of polyhedral arrays. Moreover, studies were made about the estimation of large area insolation, based on the horizontal surface insolation data collected at 21 sites of residential photovoltaic power systems in the Kanto district. (NEDO)

  14. FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the system evaluation technology; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Based on the evaluation method for the performance prediction system of the standard photovoltaic power system, the R and D were conducted of the system generation output prediction technology which is general-purpose, simplified and applicable to various kinds of photovoltaic power system for residential use, and the FY 2000 results were summed up. In this fiscal year, the photovoltaic power system for residential use was increasingly installed at 15 places, and 100 sites in total were made database and analyzed. As to the development of simulation technology, technology of calculation was established such as the simulation of multi-plane array composition and correction of multi-plane array incidence. Further, technical information on system trouble and knowledge/information/proposal for reducing power generation loss were arranged by design parameter. Using the data on solar radiation/power loss at sites of residential use photovoltaic power systems installed in the Kanto area, value analysis of the capacity of wide area facilities of the photovoltaic power system was made by the statistical method. This study was compiled into the revised edition of design manual. (NEDO)

  15. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

  16. Report on results concerning development of supermetal technology (FY1999-2000). Development of evaluation technology for formability of super metal (development of evaluation technology for formability of recrystallized microstructured plate); Super metal no gijutsu kaihatsu seika hokokusho (1999 - 2000 nendo). Super metal no seikeisei hyoka gijutsu nado no kaihatsu (bisai saikesshotsububan no seikeisei hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In connection with the innovative manufacturing of large base materials having a mesoscopic grain structure by means of technologies for high deformation accumulation control, recovery/recrystallization control, etc., research was conducted on evaluation technology for various characteristics such as formability, with fiscal 2000 results compiled. For the purpose of evaluating average grain size from an optical microscopic photograph of structures, it was judged reasonable to determine the average cut piece length. A device introduced to this development project was a horizontal goniometer capable of ODF (crystallite orientation distribution function)/pole figure measurement, qualitative analysis, and residual stress measurement. With warm rolling performed by controlling both material temperature of 7475 based alloys and roll temperature, thermally stable micro sub-grain structures were obtained. As a result of ODF analysis of this warm-rolled material, it was found that a {beta} orientation group existed very sharply in the area from the sheet surface to the center planar part of the thickness. The grain refinement of 5083 based alloys using a warm rolling method was also successful, with its ODF analysis revealing that the accumulation of the {beta} orientation group was very high as in the 7475 based warm-rolled materials. (NEDO)

  17. Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

  18. Fiscal 1997 report on the introductory study. Human behavior recognition evaluation technology; 1997 nendo sentan kenkyu hokokusho. Ningen kodo ninchi hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Importance of the human behavior technology was paid attention to to get true safety and comfortableness of life through adaptability of products/systems to all humans. In consideration of the social and technological background, the human behavior recognition evaluation technology avoids economic/social losses caused by accidents and troubles and also provides the safe life environment for living people including the aged. Further, the gist of the project was proposed to make it clear that it can give a course of making things from a viewpoint of development of products dealing with individuals (personal fit) and can give new added values and contribute to heightening of international competitiveness at the same time. Development is made of technology of dividing concrete behavior patterns into types and also accumulating them in usable forms at the time of product design and in emergency and of technology of measuring all the time information on human behaviors in daily life without restrictions and on site. Supporting technology is developed for making the most of behavior information of users for product design and in emergency. Effects of the spread are also estimated. 76 refs., 13 figs., 9 tabs.

  19. Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

  20. Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-08-01

    Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

  1. Achievement report for fiscal 1998. Development of Assessment Technology of Life Cycle Environment Impacts of Products; 1998 nendo seika hokokusho. Seihinnado lilfecycle kankyo eikyo hyoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An inventory data collecting format is formulated, data collecting activities are launched through 23 industry associations and several investigatory agencies, and almost all the primary data are collected. All the inventory items are being rearranged into a convenient order, and efforts are under way to designate the association to be in charge and the method to be used for data collecting (the accumulation method, process model method). Problems about techniques in the veinous department are extracted. The flow of matters relating to various metals and glass after their use and the magnitude of their environmental impacts at the ultimate sites of treatment are understood though roughly. Investigations are conducted into typical formats overseas, a data arranging format is constructed, specifications are defined for a data inputting software program, and a request is placed with a dedicated dealer for the compilation of the said program. The architecture and specifications of an LCA (life cycle assessment) database system are determined, and its functions are undergoing an intermediate check by a research team for improvement. Endeavors are exerted at quantifying global warming, ozone layer depletion, biotoxicity, and photochemical oxidants for use as the basic data for damage evaluation. (NEDO)

  2. Method for evaluating environmental performance of technologies by using the interindustry relations table; Sangyo renkanhyo wo mochiita gijutsu no kankyosei hyoka shuho

    Energy Technology Data Exchange (ETDEWEB)

    Hondo, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-01-30

    This paper describes a proposal of a method for evaluating environmental performance of technologies by using the interindustry relations table, and the case studies thereof. This method is characterized in that it can evaluate two effects affecting the environment: structuring of capital facilities required in association with introduction of the technologies and the changes in social structures. As a parameter to compare the technologies considering these effects, a concept of life cycle limited emission amount was introduced. In the case studies, life cycle limited CO2 emission amounts from using seven kinds of technologies were calculated, and environmental performances of each technology were compared. The result indicated that introduction in Japan of coal, oil and LNG fired thermal power generation will increase CO2 emission amount from the whole society. Conversely, introduction of hydraulic, nuclear, photovoltaic, and wind power generation technologies will reduce the CO2 emission amount. It is pointed out particularly that hydraulic and nuclear power generation can minimize CO2 emission from structuring capital facilities, and is an excellent technology from a viewpoint of reducing CO2 emission from the society as a whole. 5 refs., 6 figs., 1 tab.

  3. Leading research report for fiscal 1998. Life landscape performance evaluation technology (Landscape Frontier); 1998 nendo sendo chosa kenkyu hokokusho. Seikatsu keikan seino hyoka gijutsu (land scape frontier)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the formulation of guidelines for the construction of an appropriate landscape in the 21st century for the creation of 'landscape industry' in a sustainable society, researches were conducted for the development of landscape materials to constitute living circumstances equipped with 'life landscape' and of technologies for evaluating them. In the landscape designing system subcommittee, the current states and problems of landscape designing systems were analyzed and problems to solve were clarified, these problems involving systems and institutions, people and collaboration, formation of a consensus, systems for production and distribution, etc. In the landscape materials subcommittee, a 'landscape cell' concept in which a life space is the unit was employed in discussing the needs for landscape materials to meet and in extracting the seeds the industry was able to offer for improvement on landscape. In the landscape evaluation subcommittee, the history and today of landscape were reviewed to define what was to be respected in the development of evaluation techniques, and guidelines were extracted towards landscape materials development and landscape industry promotion. In addition, a Landscape Frontier symposium was held. (NEDO)

  4. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  5. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  6. WE-NET substask 3. Conceptual design of total system (Safety measures and evaluation techniques); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei anzen taisaku hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work) in fiscal 1998, researches and studies were conducted to clearly define safety designs and to improve on accident-and-safety analyses. In relation with system safety design, investigations continued into Japanese and foreign manuals and regulations about the handling of hydrogen and its peripherals, and safe design guidelines (draft) were compiled. Anomalies and accidents supposed to be typical of each of the systems concerned were investigated. As for accident-and-safety analyses, incorporation of a turbulence model was studied in relation to models representing the leak, evaporation, and diffusion of liquid hydrogen, and improvement was achieved when the scope of evaluation was enlarged concerning the hydrogen detonation model. The integration of the two models was discussed for the due evaluation of a series of processes of liquid hydrogen leak, evaporation, diffusion, and detonation. Calculation was performed for two assumed accidents, and the results were found to justify the integration of the two models. (NEDO)

  7. Research, development, and evaluation of basic technologies for next-generation industries. Technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu hyoka. Saibo tairyo baiyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The project aims to establish basic technologies for the mass culture of cells by utilizing the features of animal cells, which will enable a large, stable supply of fine chemicals such as highly functional physiologically active proteins whose industrial production the conventional technique of synthesis fails to realize. For this purpose, efforts are exerted to select cells which are capable of producing target substances, to breed highly productive strains, to develop a serumless medium that satisfies demands for an all-purpose feature and heat sterilization, and to develop technologies of high-density culture and effective refining, etc. Some DNA (deoxyribonucleic acid) recombination technologies are also resorted to. As the result, a high-density culture of 2 times 10{sup 8} cells/ml has become available. Production is now feasible of various differentiation-inducing elements such as monoclonal antibodies with anti-HB virus activity, DIF, etc. Furthermore, cooperation with the Tsukuba University leads to the discovery of a novel vasopressor peptide (endothelin). The heat sterilization accepting serumless medium, which is put to practical use as the first of the kind in the world under this research and development project, contributes to the advancement of basic studies about cell biology. (NEDO)

  8. Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

  9. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for thin substrate polycrystalline solar cells (compound semiconductors and their fabrication technologies); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usumaku taiyo denchi jitsuyoka no tame no kaiseki hyoka (kagobutsu taiyo denchi zairyo oyobi seisaku gijutsu no kaiseki hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Oyagi, H; Okada, Y; Yamaguchi, H; Shiota, T; Kuroda, S; Igarashi, O; Tanino, H; Makita, Y; Yamada, A; Kimura, S; Ohara, A; Niki, S; Shibata, H; Fons, P [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for thin-film compound semiconductor solar cells. The study on epitaxial growth and optical properties of the thin films of CuInSe2 and CuGaSe2 evaluates the thin epitaxial films grown under various conditions, showing morphology of the defects at the interface of heteroepitaxial growth. These results are used to set the growth conditions under which a thin film of high luminescence by exciter recombination is produced. The study also gives information of luminescence transition in the vicinity of the band ends and of energy level between the bands. The study on structural analysis of the epitaxially grown thin films of CuInSe2 investigates dependence of lattice constants of the MBE-grown CIS layer on film thickness by the X-ray diffractometry based on the bond method. The study on epitaxial growth by the Se(CH3)2-halogen transfer method tests epitaxial growth of the single-crystalline Mo on a substrate of single-crystalline sapphire. 5 figs.

  10. FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

  11. FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

  12. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency Si solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu silicon taiyo denchi gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Suzuki, E; Ishikawa, K; Takato, H; Yui, N; Shimokawa, R [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for development of extra-high efficiency silicon solar cells. It is necessary for development of extra-high efficiency Si solar cells to extend as far as possible service life of minority carriers and to develop the evaluation techniques. Noting photoluminescence (PL) observable even with Si, the method of evaluating characteristics of minority carriers, which are not limited in samples, is developed to experimentally determine their service life from transitional response of the PL characteristics. Si has an extremely low quantum effect, because it is an indirect transitional semiconductor, and needs measurement of very high sensitivity. A rapid heat annealing apparatus and others to generate carriers in the infrared and ultraviolet regions are provided in consideration that these are possible means to increase efficiency. These possibilities will be pursued by developing the annealing techniques. 1 fig.

  13. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

  14. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

  15. FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. Separate volume. R and D of the system evaluation technology (Data book on the photovoltaic power system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu (Bessatsu : Taiyoko hatsuden system data shu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of establishing the optimum design and optimum operation technology of various kinds of photovoltaic power system, data were collected to make a data book on various kinds of photovoltaic power system of which the future commercialization is expected. Included in this data book were the monthly report on operation data on demonstrative test facilities at the Hamamatsu site of JQA (Japan Quality Assurance Organization), daily graph of insolation/temperature, monthly graph of wind direction/wind velocity. Further, as the data on the residential use photovoltaic power system, data on the following were summed up: information on the site of installation of the residential use photovoltaic power system (photo information, the state of installation such as sites installed more in FY 2000, drawings of module arrangement and measuring point layout, etc.), daily report on operation (graph of daily trends, daily report by site, hourly report by site, daily report on all sites, hourly report on all sites), operation data and performance indices, list of troubles arising in the residential use photovoltaic power system, other system information about residential use measuring data, power generation characteristics and {alpha}{sub pmax} of residential use solar cell modules, etc. (NEDO)

  16. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology - Photovoltaic system data book, separate volume); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu bessatsu (taiyoko hatsuden system data shu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the research and development of photovoltaic power generation system evaluation technology, great progress has been achieved in performance improvement and cost reduction as far as constituent devices such as power modules and inverters are concerned. In the designing of systems, however, quantitative elucidation of loss and power reduction factors remains insufficient. Under the circumstances, several types of photovoltaic power generation systems expected to be put to practical application in the future are taken up, test facilities are constructed which simulate them, and data are collected. The thus-collected data are utilized for research and development of evaluation techniques necessary for the improvement of photovoltaic system efficiency, such as design parameter quantification, databasing and utilization thereof, and simulation technologies, for the establishment of technologies for optimum designs and optimum operations. The data book accommodates data, arranged in an easy-to-use fashion, collected about verification test facility (interconnected systems, independent systems, and water pump systems) operation, weather conditions, and residential photovoltaic power generation systems. (NEDO)

  17. Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Eco-energy urban system (Research of systematization technology and evaluation technology out of energy system designing technology researches); Koiki energy riyo network system kaihatsu (eko energy toshi system) 1998 nendo seika hokokusho. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the realization of urban society respecting enhanced energy efficiency and environmental protection, cities and surrounding industrial facilities are investigated for the development of element technologies involving energy recovery, conversion, transportation, storage, delivery, utilization, etc., and for the compounding of urban energy systems. In the study of the effect of introduction, assumption is made of delivery of heat to an urban heat accumulation district from a plant equivalent to a district air-conditioning system which is covered by the existing technologies. Also assumed are the delivery of exhaust heat to the said plant utilizing eco-energy element technologies and the replacement of existing technologies by eco-energy element technologies. Comparison is established in terms of energy efficiency, environmental protection, and economy, and then it is found that the eco-energy element technologies for the utilization of exhaust heat are in all cases superior to the conventional technologies as far as energy efficiency and environmental protection are concerned. It is found, however, that they are inferior from the economic viewpoint. The energy efficiency technology in heat transportation is superior to the existing technology in energy efficiency and environmental protection but roughly equal to the existing ones in economy. (NEDO)

  18. Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

  19. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

  20. Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

  2. FY1995 comprehensive assessments of measures mitigating heat island phenomena in urban areas; 1995 nendo heat shinku wo riyoshita daikibo reibo system no kaihatsu (daitoshi ni okeru kaki koonka taisaku gijutsu no hyoka shuho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The urban heat-island phenomenon is one of the man-made changes of local climate. The objectives of this research are to develop a heat-island model to cover the building scale to mesoscale and to assess the countermeasures to heat- island effects. The analysis of Tokyo by remote-sensing, field observation and estimates of anthropogenically exhausted heat using energy consumption data were conducted. And, techniques to assess the most effective countermeasure against the urban warming were developed. (NEDO)

  3. International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

  4. Research and development of basic technologies for the next generation industries, 'bio-elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihtsu 'bio soshi'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed in order to establish basic technologies to realize new information processing incorporating high-order functions of living organisms, and bio-elements equipped with high-order functions. In the field of developing technical means to measure directly the information processing function of living organisms, detailed analysis has become possible for the first time on spatial operation of nerve activities by using two-dimensional beam measurement operation on the nerve activities. In the field of aiming at modeling, a system to realize functions effective in terms of engineering was structured by incorporating into the model the functions specific to nervous systems of visual sense and motion. In the field of element technologies, a large progress was seen in the basic technology and evaluation technology such as design and fabrication of molecules added with different functions in the LB membrane. Membranes having simple but different functions such as light beam and scent detection were manufactured, whereas a possibility of having them manifest functions as elements was verified. Furthermore, possibilities were discovered in manufacturing functional membranes by using self-organizing capability as a result of using basic properties possessed by polymers, and in realizing functions simulating plasticity of nerves. These achievements would lead to a belief that the targets of the first term research and development have been achieved nearly completely. (NEDO)

  5. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

  6. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  7. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  8. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  9. Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

  10. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  11. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  12. Investigational study of evaluation of the global energy system as a global environmental protection technology; Chikyu kankyo taisaku gijutsu toshite no global energy system no hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    With relation to some global energy systems of which viability is predicted in the future, an evaluation was conducted from the viewpoints of economical efficiency, energy balance, CO2 emission, etc. The fossil fuel CO2 capture system, the conventional thermal power plant added with CO2 recovery/treatment facilities, is expected to reduce approximately 70-75% of the CO2 emission. The fossil fuel decarbonated hydrogen system, which decarbonates fossil fuels, recovers/treats CO2 at the place of fuel supply and uses as hydrogen, is of poor practical application from an economical point of view. The fossil fuel methanol synthesis system, which synthesizes methanol from fossil fuels at the place of fuel supply, generates electric power and recovers/treats CO2 with the methanol, is large in energy loss and CO2 emission and low in overall efficiency and CO2 reduction effect at the time of methanol synthesis. The renewable energy hydrogen system is an ultimate system with no emission of CO2, though it costs much. 110 refs., 83 figs., 107 tabs.

  13. Report on final evaluation of industrial science and technology research and development system. Comprehensive basic technologies for development of ocean resources. Manganese nodule exploitation system; Kaiyo shigen sogo kiban gijutsu (mangan dankai saiko system). Saishu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    Described herein are the final evaluation results of the basic research and development of the system for exploiting manganese nodules as one of ocean resources. A 9-year project was started in the FY 1981 to establish the techniques to efficiently, economically exploit Mn nodules on a commercial basis, which are occurring on deep sea bottoms (4,000 to 6,000 m deep), in order to stably supply non-ferrous metallic resources, e.g., Ni, Cu, Co and Mn, which are essential for economic activities of Japan. Originally, the UN convention related to ocean laws raised development of unique exploitation techniques as the prerequisite condition for obtaining the right to develop Mn nodules. However, the situations around development of Mn nodules were changed since then, to devalue objects, significance and urgency of this project. The fourth amendment of the basic plans decided to suspend the comprehensive ocean tests in 1996, and to implement only the ocean/land tests in which part of the individual elementary techniques were combined. Therefore, the technological validation of the overall system could not be done sufficiently, and degree of achievement of the project is low, viewed from insufficient prospects of the commercial production. However, this project produced good results in individual elementary techniques, which are of significance for the resources policies. (NEDO)

  14. FY 1999 report on the results of the R and D on the assessment of reliability of oil refining facilities; 1999 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At present, in oil refineries in Japan, the term of the continued operation in oil refining facilities is shorter than that in Europe and America because of the regulation on the open inspection period for boilers and hazardous material storage tanks. As a result, the refining cost is comparatively higher than in Europe and America due to the increase in inspection/repair cost and decrease in operational rate. Therefore, it is becoming important to effectively supply petroleum products by keeping stability in oil refining facilities of the whole Japan and prolonging the term of the continued operation of oil refining facilities, etc. In this R and D, the technical development is conducted which is needed for the long-term continued operation of oil refining facilities. The items for the R and D are as follows: assessment technology of reliability of oil refining high temperature system facilities, assessment technology of reliability of piping/storage facilities in oil refinery, assessment technology of reliability of oil refining power system facilities, technology of management support system in oil refining facilities. In this fiscal year, technical survey, data collection, and construction of the basic concept of developmental technology were mostly conducted. Also conducted were trial manufacture of various probes for non-fracture inspection use, oscillators, etc., and basic design of inspection equipment and trial manufacture of a part of them. And the data acquired were analyzed. (NEDO)

  15. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzokukei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-31

    The results of the first phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to understanding the basic characteristics regarding wettability and reactivity of PAN-based carbon fibers and PCS-based silicon carbide fibers with metals, in which aluminum-based matrices are considered; preliminary tests for various composting methods; and development of wire preforms as the intermediate materials. Bright prospects have been obtained for improving problems involved in each technique. For development of molding/processing techniques, basic researches have been conducted for hot pressing/rolling, extrusion/withdrawal, powder molding and melt molding, using various reinforcing fibers. Bright prospects have been also obtained for combinations of adequate molding processes for individual materials. For development of design techniques, the basic data regarding mechanical characteristics of FRMs, both domestic and foreign, are collected, and analyzed by the trace tests with specimens, to set up the targets for FRM function improvements, viewed from the designs. (NEDO)

  16. Research and development of the industrial basic technologies of the next generation, 'composite materials (fine ceramics)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fine ceramics'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    The results of the first phase research and development project for developing fine ceramics as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop fine ceramics of high strength, corrosion resistance, precision and wear resistance, noting their excellent characteristics. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at development of silicon nitride and silicon carbide for synthesis of the stock materials; explosive forming/treating the stock powders; forming, sintering and processing/joining; evaluation of the characteristics; non-destructive testing methods; designs; and evaluation of the parts, among others, as the elementary techniques for production, evaluation and application of the fine ceramic materials. The technical targets of improving functions have been achieved, or bright prospects have been obtained therefor in development of the techniques for synthesis of the stock materials, forming/sintering and processing/joining. The silica reduction for stock synthesis, basic techniques for molding/sintering, and rheological considerations for the molding/sintering techniques represent the techniques of the next generation, because they break through the limitations of the conventional techniques. (NEDO)

  17. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the second phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei). Dainiki hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-31

    The results of the second phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. The second phase (FY 1983 to 1986) project is carried out to achieve the objectives, which are set up based on the objectives for the basic designs and the results of the first phase project. As a result, the concrete (promotion objectives), including those related to mechanical characteristics, have been almost achieved. For development of the highly functional FRP materials, the R and D efforts are directed to improvement of their moldability while satisfying the requirements of high functions, e.g., resistance to heat, leading to development of the basic techniques for epoxy resin-based intermediate materials. These results indicate possibility of commercialization of highly heat-resistant polyimde resin-based and novel resin-based intermediate materials. The results of the novel molding/processing methods, taken up in the second phase project as the ones which use no autoclave, are rated that they are developed to suggest possibility of the eventual commercialization, although the products they give are not always showing sufficient mechanical properties. (NEDO)

  18. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

  19. International research cooperation in fiscal 1997. Report on the research, development, and evaluation of environmentally-friendly combustion technologies; Kokusai kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the research and development of environmentally-friendly combustion technologies that had been conducted for six years beginning in 1992, analysis and discussion were made by a special committee dedicated to the evaluation of the efforts, and the outcome is stated. In the study of zeolite-base catalysts, a highly active catalyst was developed which assumes a multilayer structure of mordenite, etc., with titanium introduced thereinto using an NO-selective reducing catalyst. As for metal complex oxide-base catalysts, various catalysts high in activity were developed, based on saponite which is a laminar, clayey compound. As for alumina-base catalysts, details were learned of the reaction mechanism and catalysis activation sites and, helped by the findings, a silver-supporting alumina catalyst was produced. In the study of direct decomposition type NOx removing catalysts, a success was achieved in causing NO to be decomposed with high selectivity in an oxygen atmosphere by use of new-type electrodes, functional layers, and solid electrolytes. In the field of catalytic combustion, a PdO-Pt/Ba-Al2O3 catalyst was developed, which is to serve for a hybrid type catalytic combustion method. 19 refs., 112 figs., 25 tabs.

  20. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

  2. Report on the final evaluation on the 'development of a bituminous coal liquefaction technology (NEDOL method)' in the Sunshine Project; Rekiseitan ekika gijutsu (NEDOL ho) kaihatsu saishu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    Development of a bituminous coal liquefaction technology (NEDOL method) can be judged appropriate as a national project in the comprehensive view with the 21st century just around the corner. It is a fact that this project has spent the national budget not in a small amount. There is no prospect of the technology to be put into practical use in Japan at the present time. The coal liquefaction technology is a technology required inevitably in the situation where shortage of crude oil supply may endanger the existence of a nation. Therefore, there is sufficient significance in having demonstrated the effectiveness of the NEDOL method which can be applied to a large number of coal types and expected of high liquefaction yield. The contents of the 'technological package' to be prepared are so demanded that its usefulness can be retained until the time of a demonstration plant design and operation will come in the future. It is also desired that the human resources and the testing devices will be kept ensured, and the technologies developed under this project will be maintained and expanded. The present technology has low necessity of immediately putting into practical use in Japan at the present time. However, the technology should be kept available for use at any time, and retained for use in an urgent situation. (NEDO)

  3. WE-NET substask 3. Conceptual design of the total system (City-level energy estimation and assessment); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei (toshi kibo deno yosoku hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The effort of fiscal 1997 at isolating the best way to introduce a relatively small amount of hydrogen into urban fuel economy was carried over to fiscal 1998. In the research of fiscal 1998, comparison was made between Tokyo and London in connection with hydrogen introduction, and a transition scenario was proposed for introducing hydrogen into Tokyo. Models were built for Tokyo and London, and studied. The result of this study was different from that obtained in the previous study, and places the two cities under similar conditions. The difference is attributed to the rapid progress in the development of the fuel cell and to the resultant reduction in cost. It is inferred that, in consideration of the transportation situation, the introduction of pure hydrogen will be the most cost-effective for both cities at least for some time to come. According to the revised data, natural gas may be procured in Tokyo as in London but the size of supply available in Tokyo is fairly smaller than that in London. Several transition scenarios covering the period up to 2025 were subjected to discussion. (NEDO)

  4. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  5. Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

  6. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  7. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  8. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    The results of the first phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. This project is aimed at development of the resin-based composite materials as light, high-strength and high-rigidity structural materials. Development of the basic techniques for these materials is of high significance, and highly rated. The first R and D phase efforts are directed to synthesis of new skeleton and terminal compounds, and their introduction into the matrices; application/combination of various fiber surface modification techniques; development of the basic techniques for intermediate materials for three-dimensional fabrics, triaxial fabrics and hybrid materials; improvement of the main techniques for a series of molding/processing steps; adoption of new methods; and development of design programs and elementary design techniques. The technical targets of improving functions of each item have been achieved, or bright prospects have been obtained therefor, each involving potentials of functional improvements by developing new functions. It is also considered that the parallel, competitive development and promotion of 7 routes in researches on the matrix resins have brought great effects. (NEDO)

  9. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

  10. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'taikankyo kyoka soshi'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    Research, development and evaluation were performed with an objective of developing environment resistance strengthened elements, with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments. The objective for the first term is to develop the basic technology on element structures required to raise the environment resistance, and the methods of testing them. With regard to heat resistant elements, {beta}-SiC single crystal thin films were formed, and a prospect was obtained on using them as the elements. Regarding MOS integrated circuit, bipolar integrated circuit, and GaAs element, points presenting the largest issue in radiation resistance were noticed according to respective elements. Thus, temperature for gate oxide film formation was lowered, element structures were improved, and gate lengths were decreased to enhance the radiation resistance. For the evaluation test technology, a provisional testing method was prepared for the radiation resistance, a prototype in-situ irradiation testing device was fabricated and so was a prototype high-temperature testing device usable up to 500 degrees C. These achievements lead to a belief that the targets for the first term have been achieved. (NEDO)

  11. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

  12. FY 1993 Research and development of ceramic gas turbines. Development of methods of testing and evaluating ceramic member bonding techniques; 1993 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    Studies are conducted to establish the methods of testing and evaluating applicability of ceramic-metal bonding for ceramic gas turbines, and the FY 1993 results are reported. The program involves measurement of residual stress by the X-ray method and durability tests for the joints of silicon nitride and austenitic stainless steel with copper as the intermediate layer, and analysis and classification of the strength/durability test results obtained until the previous fiscal year by the finite element method, to evaluate applicability of the joining. For the strength characteristics at high temperature, the test pieces tend to lose strength at 400 degrees C and higher, and high-temperature strength as cross-head displacement speed increases. The upper limit of bending strength at room temperature decreases as number of thermal cycles increases. The test pieces subjected to thermal cycles have a higher bending strength at high temperature than at room temperature. The results of the two-dimensional plasticity analysis of the residual stress in the joint by the finite element method are in good agreement with the results by the X-ray method. (NEDO)

  13. Fiscal 1999 report on results. Development item, 'development of evaluation technique for biocompatibility and the like of porous materials'; 1999 nendo takozairyo no seitai tekigosei nado hyoka gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing fundamental technologies for ceramic porous materials that are excellent for artificial bone for a living body, evaluation technologies were developed for mechanical properties and biocompatibility, with fiscal 1999 results compiled. Performed for the examination of the mechanical properties were flexural test, compression test, tensile test, shearing test, torsion test, fatigue test, etc., with an evaluation testing method studied assuming that ceramic porous materials were applicable to implanting members. In the evaluation of biocompatibility, five kinds of osteoblast-like cell lines were cultured on a plastic disk and a dense hydroxyapatite disk, with adhesion and proliferation of the cells compared. Since these osteoblast-like cell lines adhere and proliferate on the surface and in the pore of hydroxyapatite, evaluation of the biocompatibility such as cell affinity was found possible with this in vitro method. With the view of obtaining principles for designing new bioactive ceramics, a method was developed for evaluating apatite-forming abilities of metal oxide gels having different compositions and structures in simulated body fluid. (NEDO)

  14. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  15. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the second phase research and development; Jisedai sdangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzoukei)'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    The results of the second phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to modification of PAN-based high-strength carbon fibers for aluminum-based FRMs, and also to development of the methods for controlling interfacial reactions at high temperature by modification of the base materials for titanium-based FRMs. For development of carbon fiber-based intermediate materials, the techniques are developed for continuous production of wire preforms of aluminum. For development of molding/processing techniques, the press molding and powder HIP molding techniques are developed to give a planar product of the FRM of titanium alloy reinforced with evaporated filaments of silicon carbide, which shows an average tensile strength exceeding the target level. Also developed are the press and roll molding techniques for the wire preforms of aluminum reinforced with silicon carbide fibers, the planar product therefrom showing a tensile strength of at least 99% of the base material. It is concluded that the objectives of the second-phase project are almost achieved. (NEDO)

  16. Fiscal 1999 technological survey report. Part 2. Applied technology for measuring human sense (Human sense measuring manual - basic technology for sense evaluation); Ningen kankaku keisoku manual. 2. Kankaku hyoka kiban gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A method of measuring/evaluating a mental and physical state by means of physiological information developed by a project was compiled into a 'guide book', as was a method of evaluating adaptability to the environment or products; and, this manual was prepared for the purpose of improving the adaptability of human beings to products by making use of the guide book widely in the field of industrial manufacturing. The part 2 explains a hard measuring instrument, evaluation device, simulation system, method of data analysis, etc., as 'basic technology for sense evaluation'. The chapter 1 is a new measuring and evaluation device (device for measuring physiological signals on the surface of the body, device for measuring visual characteristics, measuring device of in vivo substance, measuring device of thermal response, and system for evaluating adaptability of practical form), the chapter 2 is a new simulator (model of human body temperature with clothes on, human comfort meter, perspiring thermal manikin, and autonomic nerve control model in cardiac blood vessel/respiratory system), and the chapter 3 is new experimental/analytical method (new data analysis method and subjective evaluation questionnaire for stress assessment). (NEDO)

  17. Research and development of basic technologies for the next generation industries, 'bio-elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihtsu 'bio soshi'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed in order to establish basic technologies to realize new information processing incorporating high-order functions of living organisms, and bio-elements equipped with high-order functions. In the field of developing technical means to measure directly the information processing function of living organisms, detailed analysis has become possible for the first time on spatial operation of nerve activities by using two-dimensional beam measurement operation on the nerve activities. In the field of aiming at modeling, a system to realize functions effective in terms of engineering was structured by incorporating into the model the functions specific to nervous systems of visual sense and motion. In the field of element technologies, a large progress was seen in the basic technology and evaluation technology such as design and fabrication of molecules added with different functions in the LB membrane. Membranes having simple but different functions such as light beam and scent detection were manufactured, whereas a possibility of having them manifest functions as elements was verified. Furthermore, possibilities were discovered in manufacturing functional membranes by using self-organizing capability as a result of using basic properties possessed by polymers, and in realizing functions simulating plasticity of nerves. These achievements would lead to a belief that the targets of the first term research and development have been achieved nearly completely. (NEDO)

  18. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  19. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of solar cell evaluation system (Survey of research and development of solar cell evaluation system); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi hyoka system no kenkyu kaihatsu (taiyo denchi hyoka system no kenkyu kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The fiscal 1999 results of survey and research conducted for the establishment of solar cell performance evaluation and reliability evaluation methods are reported. In the development of a super high fidelity (broad spectrum) solar simulator for cell evaluation, a prototype was tested for performance evaluation, and initially set values were achieved. In the development of a large-area module evaluation technology, the radiation area was increased to be 1.0m times 1.0m large. Outdoor exposure tests continued at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and analyses and databasing were carried out for the outputs of various types of solar cell modules. As for the problem of coloring of fillers which are module constituents, coloring in the U.S. was attributed to high temperature and intensive insolation, and in Austria to an oxidation inhibitor. In the development of a photo-accelerated degradation testing method for Si-based solar cells, application of the cycled illumination test was found feasible. In this test method, an amorphous silicon solar cell retains 70% of the initial Pmax value even after the passage of a period equivalent to 30 years. (NEDO)

  20. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation of peripheral technology for photovoltaic power system (analysis and evaluation on photovoltaic systems); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Shuhen gijutsu kaihatsu no tame no kaiseki hyoka (taiyoko hatsuden system shingata chikudenchi)

    Energy Technology Data Exchange (ETDEWEB)

    Kurokawa, K; Endo, E; Tsuda, I; Nakamura, K; Sugiyama, Y; Nakazawa, S; Takaku, K; Yanagisawa, T; Kojima, T; Shimizu, K; Koyanagi, T; Onda, N; Nozaki, K; Negishi, A; Kaneko, Y [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation of new storage batteries for photovoltaic power systems. Quantitative analysis and evaluation are made for introduction of intermittent operational mode in the conventional power supply system in which electrolyte units are connected in parallel and for improved performance by bubbles flowing into the line that supplies the electrolyte to the stack, in order to establish the configurations of and operational procedures for the redox flow batteries. The study on development of redox battery compares the Pb-Sn alloy felt collector with carbon fiber, Pb-Sb alloy felt and the lattice for the conventional lead acid battery, in order to optimize the new lead felt battery. As a result, it is found that the Pb-Sn alloy felt collector is better than any other device tested, because of its higher freedom with respect to electrode shape and battery size. The study on reliability evaluation of amorphous solar cells tests photoelectric conversion efficiency of a-Si solar cells, in order to elucidate the phenomena where degradation and rejuvenation compete with each other under weak light irradiation conditions. 8 figs., 1 tab.

  1. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for extra-high efficiency solar cells (research on new concentrator modules); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (shingata shuko module)

    Energy Technology Data Exchange (ETDEWEB)

    Tanimoto, J; Sakuta, K; Sawada, S; Yaoita, A [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation of concentrator modules for extra-high efficiency solar cells. The outdoor exposure tests have been under way for 3 years for fluorescent plates, as part of the research program for development of materials and elementary techniques, and essentially no degradation has been observed by the perylene pigment test. Coupling of the fluorescent concentrator and solar cell units is investigated for the coupling position and method, to theoretically analyze geometrical coupling efficiency, where they are coupled at the bottom faces in consideration of easiness of module fabrication. It is demonstrated that a high coupling efficiency can be realized when the cell is sufficiently wide relative to thickness of the fluorescent plate. The coupling method is experimentally examined using transparent silicon gel. A prototype module having the same size as the commercial module (420mm by 960mm) is made on a trial basis, where a total of nine 20mm-thick cells are cut out of a single-crystalline silicon solar cell, 100mm by 100mm in size, and are connected to concentrators at the bottom faces. It shows 2.3 times increased output by the test using a large-area solar simulator. 2 figs.

  2. Survey for development feasibility in fiscal 1999 investigation of geothermal development and promotion. Evaluation report on practicability technology survey SWD method (Evaluation report concerning verification test); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kaihatsu kanosei chosa. Jitsuyoka gijutsu chosa SWD ho hyoka hokokusho (jissho shiken ni kakawaru hyoka hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    An evaluation test was conducted on SWD (Seismic While Drilling) method as a part of the investigation of geothermal development and promotion. The test was implemented at the time of drilling of N11-MD-3 well in the northeast base area of Busadake, Hokkaido. The test items were such as verification of direct waves propagating from a bit to the surface, identification of signals passing through a fault zone using direct waves and reflected waves, estimation of distance between a fault and a bent zone, and grasping the direction of signal propagation at the time of inclined drilling. As a result of the experiments and studies, following conclusions were obtained. Reflected waves extracted are not necessarily limited to those from a reflection area from which the shape of a fault can be grasped; unless there is a clear reflection area that can be picked up on the surface near a fault, the application of this method is not effective. In an analysis using direct waves, it was possible to obtain an inclined angle of a fault plane from the estimation of velocity structure, propagation route, and assumption of the shape of the fault plane and, therefore, to grasp the shape of the fault. Obtaining reference data is essential for identifying bit signals. (NEDO)

  3. Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. The current fiscal year performed data collection and long-term continuous operation according to the durability test program for the device installed with inverter to protect grid connection, as the continuation from the previous fiscal year. In the electrical characteristics, although no large changes have been found in AC overvoltage and AC undervoltage, instability was observed in the detection level. With regard to temperatures in different components, the temperature rise has become nearly the same as in the maximum output continuous operation as a result of the repetition of the operation and shutdown, whereas the influence on the electrical and thermal stresses have increased. Particularly, when temperature rise in the AC side noise filter was given observation, the measurement of conductive high-frequency terminal voltage showed a value higher by several ten dB than in the previous fiscal year. The current fiscal year has gone farther to starting the measurement of noise electric field intensity as the base of electromagnetic interference. (NEDO)

  4. Fiscal 1994 research report. Demonstration test for establishing technology for peakload shaving with dispersed small residential PV systems (Evaluation of weatherability of house-use solar light electric power generating system equipment); 1994 nendo jutakuyo taiyoko hatsuden fuka heijunka gijutsu nado kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutakuyo taiyoko hatsuden system kiki no taikosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Weatherability tests such as exposure to the atmosphere are conducted to collect and accumulate information on the degradation of house-use photovoltaic equipment expected to come into use in areas where weather conditions are hostile. Based on the thus collected data, analysis and evaluation are conducted about the mechanisms of corrosion and degradation for the establishment of designing and evaluating methods for maintaining weatherability. Since fiscal 1994 is the first year of the project, preparations are made for tests to be conducted. In carrying out research activities, a Weatherability Evaluation Committee for House-Use Solar Light Electric Power Generating System Equipment is organized, who discuss implementation of the project. Discussion is made on the shape and structural materials of the exposure rack. An aluminum alloy coated with a clear coating of alumite sulfate is selected, and a rack is built. Specifications of a sea salt particle collector are discussed, and preparations are made for arresting and quantifying sea salt particles under the Japanese Industrial Standard (JIS) dry gauze method and the International Organization for Standardization (ISO) wet candle method. Solar cell module initial characteristics are measured. (NEDO)

  5. Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. In discussing the durability test items, electrical property changes were observed on AC overvoltage, AC undervoltage, frequency rise, and frequency fall, as the continuation from the previous fiscal year, in order to evaluate temperature rise in different parts due to lapse of operation time and the effects of thermal stress in each component on the stress of the entire product. Furthermore, verification of single operation detecting function, tests on sudden input power change, sudden grid voltage change, and measurement of conductive high frequency terminal voltage were conducted in addition to the above observations. In discussing the durability test methods, repetition of operation and shutdown during the rated operation was adopted in place of the simulated operation using variation in the insolation having been discussed in the previous year. As a result of the tests, no noticeable changes were recognized from the evaluation result after a lapse of 5,000 hours from the start of the operation, as compared to those after the aging operation. (NEDO)

  6. Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Tests and discussions have been performed on the safety and durability of the device installed with inverter to protect grid connection, being an important device in the photovoltaic power generation system. The particularly important requirements demanded in the device were specified as maintenance of electric power quality, coordination with the protection system in the grid side, and assurance of safety of personnel and facilities. The current fiscal year has performed operation corresponding to that in the actual field for 20 years in total, and the evaluation tests on electrical characteristics and electric power quality. This paper summarizes the achievements in four years including the results available up to the previous fiscal year. Although no large change has been identified in the electrical characteristics, variance has been found in the detection time of overvoltage in the grid side. With regard to the electric power quality, the value has exceeded 89 dB as the determining condition for the certification test in the conduction interfering waves of 5 kHz to 10 kHz. In addition, it was confirmed that the conductive high-frequency noise terminal voltage in the grid side after the repetition of operations and shutdowns tends to increase according to the operation lapse time. (NEDO)

  7. New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Research and development of solar cell evaluation system - Survey of research and development of solar cell evaluation system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys and studies were conducted for establishing methods for evaluating solar cell performance and reliability. In the effort to develop basic technologies for the comprehensive evaluation of the performance of various types of solar cells and modules, an ultrahigh matching solar simulator and a large area solar simulator were built. The long-term exposure tests of solar cell modules kept on at 5 sites in Japan, 3 sites in Australia, and 1 site in Oman, and the databasing of the test data was planned. In the long-term evaluation of solar cell durability, investigations centered about module deterioration, where abnormal heat generation was observed, cause of increased resistance was inspected, and separation between the cell and the filler was examined. In the development of an accelerated photodegradation test method, it was found that the result of a light-dark cycle test with the ambient temperature varied agreed excellently with the results of outdoor exposure tests. It was consequently proved that the light-dark cycle test was a very promising candidate for an accelerated photodegradation test for a-Si solar cells. (NEDO)

  8. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for development of extra-high efficiency solar cells (fundamental research on extra-high efficiency III-V compound semiconductor tandem solar cells); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Chokokoritsu taiyo denchi no gijutsu kaihatsu no tame no kaiseki hyoka (chokokoritsu III-V zoku kagobutsu taiyo denchi gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Kawanami, H; Sakata, I; Nagai, K; Matsumoto, K; Miki, K [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of extra-high efficiency III-V compound semiconductor tandem solar cells. Heteroepitaxial structures of compound semiconductors, such as GaAs, on silicon substrates are analyzed and evaluated by EXAFS, Raman and RHEED for the initial stage of the film growth and heterointerfaces. The device capable of in-situ observation of the growing surface structures during the period of heteroepitaxial film growth is introduced, to investigate the effects of rise-up and initial growth conditions on defects. The effects of atomic hydrogen on growth of a GaAs film on a silicon substrate are investigated from photoluminescence and solar cell characteristics, to confirm the effects of reducing defects. Heteroepitaxial growth of InGaP, which has the optimum band width for forming multi-junction silicon solar cells, on a silicon substrate is investigated, to find that an interfacial buffer layer is necessary to form a good film. 2 figs.

  9. Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

  10. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Conceptual design of the total system (safety measures and evaluation technology); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Zentai system gainen sekkei (anzen taisaku hyoka gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Safety measures and assessment technology were studied for the WE-NET project. As the study result in fiscal 1996, the information on safety design, anomaly and accident was collected and arranged. The information on safety measures, ideology and criterion was also collected by visiting some domestic and overseas organizations experienced about handling of liquid hydrogen (LH). The initial survey was made for the safety design ideology, analytical technique and disaster preventive measures of LNG systems as the similar cold liquid system. Accidents and explosion accident of a hydrogen production plant (water electrolysis) in Germany were analyzed. Events on storage tanks and leakage around the tanks were studied as typical risk of LH considering temporary and LNG system design information. The model based on the LH spillage test result and 3-D dispersion of vapor cloud were prepared by modifying a simulation code. The model allowed evaluation of the effect of explosion and fire accidents of compressed hydrogen gas and flying fragments on structures and people, and visual display of distances from a tank and damage conditions. 19 refs., 29 figs., 18 tabs.

  11. Report on achievements of commissioned studies on research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 5 for research and development of a correlation and evaluation technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Sokan hyoka gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This paper describes the research and development of (1) working environment having human senses and affinity at nuclear electric power plants, (2) a correlation technology for comfort in composite environments composed mainly of warm heat environment, (3) space-type human interface adapted to human senses, and (4) a human comfort meter. With regard to the subject (1), improvements were made on the experimental facilities, data processing systems, and environment improving devices, and data were collected and evaluated from subject experiments. With regard to the subject (2), 'development of a system to investigate correlation among externally stimulating environment, physiological effects, and sense volume based on a physiological reaction model', and 'research and development of a quantitative evaluation technology for comfort in composite environments composed mainly of warm heat environment' were executed. With respect to the subject (3), 'measurement of factors in visual sense operating environment affecting mental burden feeling', 'development of space-type human interface', and 'research on a method to utilize the eyeball movement information' were carried out. With regard to the subject (4), a warm heat sensing element structure was developed. In addition, a comfort determining software was completed that calculates hot-cold heat sense of a human body from different conditions of the warm heat sensing elements. (NEDO)

  12. Report on achievements of commissioned studies on research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 4 for research and development of a correlation and evaluation technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This paper describes the research and development of (1) a method to evaluate warm heat comfort by living scenes of workers by using a human body heat model, (2) a sense volume estimation method using skin temperatures, and (3) a stress measuring technology and a stress relaxing technology by using scent. With regard to the subject (1), the studies having been performed for the past three years incorporated into the human body heat model development such new elements as artery-vein shunted blood vessel and two-system circulation net, and an attempt was made to introduce a conception called AVA activity in the hot-cold heat sensing estimation model. The current fiscal year has carried out collecting basic data for two-model development, and structuring the human body heat model and the hot-cold heat sensing estimation model, and the warm heat environment presenting and measuring system. With regard to the subject (2), such researches were carried out as the 'research on elucidating the correlation between sensing volume and skin temperatures', 'research on the skin temperature changing mechanism', and 'development of a face heat model'. With respect to the subject (3), the hormones noted as the adrenal gland hormone are epinephrine, nor-epinephrine, and dopamine belonging to catecol amine (CA) known as the adrenal gland medulla hormone, and cortisol (CS) being the adrenal gland cortex hormone. The researches in the first term elucidated the interesting relationship between these hormones and negative emotion. (NEDO)

  13. Report on achievements of commissioned studies on research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 4 for research and development of a correlation and evaluation technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This paper describes the research and development of (1) a method to evaluate warm heat comfort by living scenes of workers by using a human body heat model, (2) a sense volume estimation method using skin temperatures, and (3) a stress measuring technology and a stress relaxing technology by using scent. With regard to the subject (1), the studies having been performed for the past three years incorporated into the human body heat model development such new elements as artery-vein shunted blood vessel and two-system circulation net, and an attempt was made to introduce a conception called AVA activity in the hot-cold heat sensing estimation model. The current fiscal year has carried out collecting basic data for two-model development, and structuring the human body heat model and the hot-cold heat sensing estimation model, and the warm heat environment presenting and measuring system. With regard to the subject (2), such researches were carried out as the 'research on elucidating the correlation between sensing volume and skin temperatures', 'research on the skin temperature changing mechanism', and 'development of a face heat model'. With respect to the subject (3), the hormones noted as the adrenal gland hormone are epinephrine, nor-epinephrine, and dopamine belonging to catecol amine (CA) known as the adrenal gland medulla hormone, and cortisol (CS) being the adrenal gland cortex hormone. The researches in the first term elucidated the interesting relationship between these hormones and negative emotion. (NEDO)

  14. Fiscal 1997 survey report. Subtask 3 (hydrogen utilization worldwide clean system technology) (WE-NET) (total system conceptual design/safety measures/evaluation technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 3 zentai system gainen sekkei - anzen taisaku hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the study of safety measures in WE-NET, the paper described the fiscal 1997 results. For drawing up a policy for safety design, technology of preserving hydrogen at high temperature/pressure, continuing collecting information on existing plants (liquid hydrogen, LNG). Investigating manuals of NASA and NASDA and also referring to people`s opinions at chemical plants, etc., the study entered into the setting-up of the safety policy and design standards. Examples of anomalies/accidents were extracted, and classification/arrangement were commenced of the measures for anomalies of detection/prevention/protection. Toward the diffusion of hydrogen and the enhancement and unification of explosion/fire simulation models, the extraction of problems has been almost finished. The second mini work shop on safety was held in the U.S., and exchanges of information were made among researchers of each country. All agreed on the importance of collecting data as the base of safety standards. As to safety measures in various tests using combustor evaluation experimental facilities, experimental equipment for materials under liquid hydrogen and experimental equipment of thermal insulation under liquid hydrogen, problems were extracted between researchers and people concerned with safety measures, and the measures to solve them were studied. 18 refs., 31 figs., 10 tabs.

  15. FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 4. R and D of correlation/evaluation technology (2); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 4. Sokan hyoka gijutsu no kekyu kaihatsu (2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    As a part of the correlation/evaluation technology, the following were conducted in this R and D. (1) R and D of space-type human interface adaptable to human sense; (2) R and D of human comfortmeter; (3) research on non-contact skin temperature measuring technology; (4) research on measuring technology of stress indicator material, and technology to relax stress using fragrance. In (1), conducted were the development of space-type human interface, study on the correlation between the visual operating environment and the mental work load/working efficiency, and development of acceleration heartbeat meter. In (2), the basic element experiment was conducted to clarify the basic concept of human comfortmeter, and the basic specifications were made clear. In (3), the experiment using person to be tested was studied to know face skin surface temperature distribution patterns, and correlations between quantity of senses such as thermal/cold senses, concentration, strain and relaxation and mental quantity. In (4), the most important subject is preparation of the environment suitable for the development of new experimental process and device/software. Therefore, the preparation was made considering listing-up of the expected experimental items, selection of common elements, systematization of hardware, establishment of rules of the experimental process, etc. (NEDO)

  16. Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 4. Research and development of a correlation and evaluation technology (Part 2); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper describes the correlation and evaluation technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In the comfort correlation in a composite environment composed mainly of warm heat environment, the experiment environment was improved, and collection was performed on basic data (cardiac blood vessel and respiration systems) required for developing a system to investigate correlation among external stimulating environment, physiological effect and sense volume based on a physiological reaction model. In evaluating the composite environment comfort, development and improvement were given on component technologies to present experimental environment for warm heat, light beam, and sound. In a space-type human interface system that adapts to human senses, the prototype system of a development platform was completed of mounting as much as half based on the basic design. Discussions were given on findings in computer inputs of eyeball movement information, and on correlation measurement of factors for visual sense operation environment affecting mental burden feeling. With regard to the human comfort meter, satisfactory result was obtained on developing structures for warm heat feeling elements and a control system for the whole body integration, and on defining the detailed specifications. However, designing of a comfort determining software has not achieved the target. (NEDO)

  17. Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 1); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The achievements during fiscal 1993 of research and development on a method to evaluate warm heat comfort by living scenes of workers by using a human body thermal model included completion of a human thermal model introduced with physiological knowledge such as artery-vein anastomosed (AVA) blood vessels and two-system blood circulation net. The effectiveness of the model was experimented and verified. It was made possible to estimate the reversal phenomenon occurring in hot heat environment, in which skin temperatures at peripheral body parts rise higher than those in the body trunk part, and skin temperature distribution. In the correlation study to estimate statistically the sense volume from skin temperatures, it was possible to estimate significantly different sense volumes from face skin temperatures, but the estimation accuracy was low because of such factors as difference in individuals. What is important in enhancing the accuracy is to identify ecological reactions of human being caused from change in the sense volume, select effective parameters, and study the mechanisms. In order to develop stress relaxing scents, discussions were given on degree of subjectivity stress by question papers and cortisol concentration in saliva as the parameters. An experimental system was developed to measure the effects of the scents to relax work stresses. A screening method was developed, whereas effects of 15 kinds of scent materials were investigated. (NEDO)

  18. FY 1991 report on the results of the contract R and D of the human sense measuring application technology. 4. R and D of correlation/evaluation technology (1); 1991 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu seika hokokusho. 4. Sokan hyoka gijutsu no kenkyu kaihatsu (1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    As a part of the R and D of correlation/evaluation technology, the following R and D were conducted in this paper: (1) high accuracy real sense visual recognition; (2) working environment at nuclear power plant with human sense and affinity; (3) amenity correlation technology in the combined environment mainly of thermal environment. In (1), the following seven items were studied: software for high accuracy real sense visual recognition; software for detecting contact of human movement with object, etc.; improvement of performance of speed of CG image indicator; harmony between image expression and video presentation; software technology for high speed modeling; measuring system under the virtual reality; production of a set of prototype system. In (2), as the environment of nuclear power plant site, visual environment of centralized control room; audio-environment of machinery room, etc., and radio-environment; environment where people have to put on special working ware, etc. In (3), development of a system to examine correlations among external stimulus environment/physiological effect/sensory quantity based on physiological reaction models; development of technology to quantitatively estimate amenity in the combined environment mainly of thermal environment. (NEDO)

  19. Development in fiscal 1999 of technology commercializing photovoltaic power generation system. Research and development of power generation application system and peripheral technologies (Survey and research on evaluation of photovoltaic power generation); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of evaluating the contribution to the global environment of utilization of photovoltaic power generation, discussions were given on evaluation of photovoltaic system life cycle, evaluation of contribution to environment, and total evaluation. This paper summarizes the achievements in fiscal 1999. In evaluating the PV system life cycle, the roof-integrated modules using the thin film CdTe cells were selected as the evaluation object to estimate the energy payback time (EPT) and the CO2 emission unit consumption rate. In case of annual production of 10 MW, the EPT is 1.8 years and the CO2 emission unit consumption rate is 13 (g-C/kWh), which were found largely reducible by expanding the annual production size. For the environmental contribution evaluation which focuses on CO2 emission suppression effect as the discussion object, discussions are being given on the introduction scenario needed for the analysis. In the total evaluation, the direct employment effect assumed in Japan was discussed on production, distribution sales, installation, maintenance control and dismantling of photovoltaic generation system for residential use. The discussion showed the effect of about 7 persons per year per MW in production size of 100 MW. (NEDO)

  20. Survey report of FY 1997 on the long-term energy technology strategy. Survey on the pre-assessment system of energy and environmental technology research and development; 1997 nendo chosa hokokusho (choki energy gijutsu senryaku chosa). Energy kankyo gijutsu kenkyu kaihatsu no jizen hyoka ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To select projects of the New Sunshine Program which is the locomotive for Japan`s research and development of energy and environmental technologies and to map out the Program`s long-term strategy, it is required to develop an effective methodology of assessing research and development themes. It is also necessary to establish the pre-assessment system which makes the assessment process more logical and which will enable the priority setting among different themes on the basis of objective and quantitative analysis. Additionally, transparency should be ensured for such a pre-assessment process through disclosure to the public and other means. The present survey aims to concretize the pre-assessment system by studying the system and techniques of an assessment system which is applicable to the research and development themes of the New Sunshine Program and is objective, quantitative and logical and which can ensure transparency and by receiving suggestions on the pre-assessment of Japan`s research and development of energies and environmental technologies through research on overseas trends of government-led research and development. 3 refs., 7 figs., 26 tabs.

  1. Report on achievements of commissioned studies on research and development of a technology to apply human senses to measurements in fiscal 1994. 2. Main issue (Part 5 for research and development of a correlation and evaluation technology); 1994 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Sokan hyoka gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This paper describes the research and development of (1) working environment having human senses and affinity at nuclear electric power plants, (2) a correlation technology for comfort in composite environments composed mainly of warm heat environment, (3) space-type human interface adapted to human senses, and (4) a human comfort meter. With regard to the subject (1), improvements were made on the experimental facilities, data processing systems, and environment improving devices, and data were collected and evaluated from subject experiments. With regard to the subject (2), 'development of a system to investigate correlation among externally stimulating environment, physiological effects, and sense volume based on a physiological reaction model', and 'research and development of a quantitative evaluation technology for comfort in composite environments composed mainly of warm heat environment' were executed. With respect to the subject (3), 'measurement of factors in visual sense operating environment affecting mental burden feeling', 'development of space-type human interface', and 'research on a method to utilize the eyeball movement information' were carried out. With regard to the subject (4), a warm heat sensing element structure was developed. In addition, a comfort determining software was completed that calculates hot-cold heat sense of a human body from different conditions of the warm heat sensing elements. (NEDO)

  2. Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 4. Research and development of a correlation and evaluation technology (Part 1); 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper describes the correlation and evaluation technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. In evaluating the warm heat comfort by living scenes of workers according to the human body thermal model, the research environment was improved by expanding the systems to measure physiological volume and the warm heat environment. Findings were acquired on the relationship between body fat rate and skin temperature, and actions of artery-vein anastomosed (AVA) blood vessels. These findings were incorporated into the research to elevate the levels of applicability of the human body thermal model. In estimating the sense volume by using skin temperatures, physiological volume being the factor of variation in face skin temperatures was elucidated, and a system to measure these variations was structured. In order to acquire the physiological volume being the factor of variation in face skin temperatures, brain wave topography measurement and {alpha} frequency fluctuation and arousal evaluation and measurement were experimented, where the effectiveness thereof was verified. Analysis was also made on blood flow rate and perspiration volume related to skin temperature variation mechanism, which has provided a number of fundamental data. For the stress measuring technology, and stress relaxation by means of scent, researches were moved forward mainly on environment improvement and preliminary discussions. (NEDO)

  3. Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 2); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Developments were performed during fiscal 1993 on a system to investigate correlation among external stimulating environment, physiological effects and sense volume based on a physiological reaction model. The development works included improvement of the model, discussions on a method to estimate parameters inside living organisms, and a method to collect subjectivity volume data. Prototypes thereof were fabricated, evaluated, and experimented, where nearly complete achievement of the targeted functions was verified. In developing a technology to evaluate quantitatively the comfort of composite environments composed mainly of warm heat environment, discussions were given on an integration evaluating expression in order not to make handling the environmental physical volume too complex. The expression models the evaluation of governing sense volume in individual environments of warm heat, light beam, and sound, and calculates the composite environment evaluation indexes by using the evaluation indexes obtained from the modeling as the descriptive variables. In developing the space-type human interface adapted to human senses, a computer system to realize the interface and the platform for function mounting were developed. The development items were broken down respectively on the basic technologies for functional aspect and surveillance and control function mounting, and the software systems. The human comfort meter achieved the basic design target. (NEDO)

  4. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

  5. Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1995. In the outdoor exposure test on solar cell modules, multi-crystalline silicon solar cell modules were selected as the test specimens, and thermo-couples were embedded in the modules to measure the temperatures. Also for the purpose of comparison, storage test specimens were stored in a constant temperature and humidity chamber. The exposure tests were carried out in three locations of the city of Choshi in Chiba Prefecture, the Miyako Island test site in Okinawa Prefecture, and the Miyako Island seashore. In the measurement and evaluation, appearance observation and measurements of output characteristics and insulation resistance were executed in summer and winter. No noticeable changes were observed in the measurements after lapse of four months and six months. In the outdoor exposure tests of metal test pieces, aluminum alloys were tested for corrosion caused by contact with different kinds of metals. Although the test period was short in the current fiscal year, difference in corrosion degrees in the aluminum alloys was found already in three months. (NEDO)

  6. Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. In the outdoor exposure tests on solar cell modules, results of the tests were derived for up to 18 months after the start of the exposure at Choshi City, Miyako Island and the Miyako Island seashore. In the appearance observation, some white rust has appeared in the contact section of the aluminum frames of the solar cell modules and fixing screws, which have been exposed at Miyako Island and the Miyako Island seashore, but no changes that may give influence on the performance of the solar cells have been observed. The results showed performance similar to or slightly inferior to that before the exposure as a whole. The insulation resistances were all found good. According to the result of the outdoor exposure test of metal test pieces, noticeable difference in the corrosion degrees was recognized in the contact corrosion section of the aluminum alloys exposed in three areas having different meteorological and environmental factors. Electroplated zinc was found to have severer pitting corrosion in the contact sections than treatment-free zinc. (NEDO)

  7. Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system, weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure. This paper summarizes the achievements in fiscal 1997. In the outdoor exposure tests on multi-crystalline silicon solar cell modules at Choshi City, Miyako Island and the Miyako Island seashore, the output characteristics after the exposure tests showed a result that the insolation intensity and the change in the short circuit current are approximately proportional, and the temperature in the module and the change in the open voltage are inversely proportional. The module characteristics retention rate showed no change in the 29-month exposure at all of the three exposure locations. The insulation resistance in the exposure test specimens have been good at 2,000 M{omega} or more in all the locations until 18 months have elapsed. However, the test specimens in Miyako Island and the Miyako Island seashore showed 99 M{omega} after 23 months, and 129 to 1,774 M{omega} after 29 months. According to the outdoor exposure tests of metal test pieces, noticeable difference was found in corrosion due to difference in the environment by each exposure location, whose order of the corrosion degree was the Miyako Island seashore > Miyako Island > Choshi City. (NEDO)

  8. Industrial and scientific technology research and development project fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Report on research and development of a brain type computer architecture `trial fabrication and high-level evaluation on chips for a large-scale artificial neural system` and on results of evaluation studies on the chips; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Nogata computer architecture no kenkyu kaihatsu `daikibo jinko shinkei kairo system yo chip no shisaku to kodo hyoka` chip hyoka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop a brain type computer architecture, a brain mimic processor (BMP) has been developed (which was made in LSI in fiscal 1997), and studies are being made on developing its applications. Development has been made on an element in which linkage of one million cells with one thousand neural cells can be realized. Evaluation substrates mounted with the BMP, control software, and compilers were provided to 15 organizations including the National Research Institutes, universities, corporations, and other societies (for 19 themes) to evaluate capability of the LSI and its application development. All of the research organizations are using these items utilizing features of the LSI or the network for such purposes as learning, storage, recognition and control. The applicable theme may include infrared spectrum pattern recognition and domain division of document images using neural network functions. It can also include structural analysis of mass spectrum molecules, time series pattern recognition, location of corresponding points in images, estimation of moving images, satellite control, character recognition, short time storage, long-term association memory models, and invention process studies, all utilizing the functions of the BMP. 71 refs., 89 figs., 9 tabs.

  9. FY 2000 report on the results of the development of the program system CO2 fixation/effective utilization technology. Development of the technology to assess global warming gas recovery/emission control by restoring/preserving the tropical mangrove coastal ecosystem; 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu seika hokokusho. Mangrove nado nettai engan seitaikei no shufuku hozen ni yoru chikyu ondanka gas kaishu hoshutsu yokusei hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of developing the technology to assess the CO2 storage amount using the tropical mangrove coastal ecosystem, survey was conducted in the mangrove tree area in Ishigaki island, Japan and in Trat province, Thailand, and a draft of the assessment method was worked out. As to the assessment of the CO2 existence amount by analysis of satellite pictures, the regression equation between the mangrove existence amount and Landsat satellite data was determined to study a method for assessment of the CO2 storage amount in the whole area for survey. Further, using the relational equation between NDVI and LAI, vegetation indices reflecting vegetation conditions, methods to estimate the CO2 absorption amount by photosynthesis of mangrove tree community, the CO2 emission amount by respiration and the net production amount. Concerning the technology to assess the terrestrial area photosynthesis CO2 absorption amount, methods were studied for direct measurement of the amount of photosynthesis/respiration of the leaf area of mangrove tree community and the respiration amount by area such as trunk, branch and root and for assessment of CO2 absorption amount. Besides, studies were made on a variety of items such as the CO2 absorption/emission amount by underwater photosynthesis/respiration and decomposition of organic substances, the seawater exchange amount, and the rate of decomposition of organic substances. (NEDO)

  10. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on evaluations of photovoltaic power generation); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Values given to global environment and economy by utilization of photovoltaic power generation are evaluated, and quantified to make clear the significance of the utilization thereof. Specifically, trial calculations were performed on LCA and damaging characteristics of photovoltaic systems, and reducible amount of carbon dioxide emission. Taking up thin film CdTe cells as the object, estimation was made on the energy payback time (EPT) and CO2 emission amount. The production scale ranges over 10 MW/ 30 MW/ 100 MW annually, the useful life is 20 years, and the unit requirement for CO2 emission originated from the charged electric power is 114 g-C/kWh. The EPT was 1.74 in the annual production of 10 MWp, 1.08 in 100 MWp, the unit requirement for CO2 emission was 14.0 in the annual production of 10 MWp, and 8.9 in 100 MWp. This is one of severals of that in the existing power supply source. For heavy metals, particularly Pb, the trial calculation resulted in 0.15 g/Wp in the crystalline type, and 0.1 g/Wp in the amorphous type. The problem therewith is separation and recovery. The reducible amount of carbon dioxide, or in other words, the amount of power that can be generated latently is 37,235 GWh/year, or 3.10 million tons when converted into carbon dioxide. (NEDO)

  11. FY 2000 report on the results of the R and D of the prediction technology for environmental effects of CO2 ocean sequestration. Ocean survey and development of the assessment technology for capacity of CO2 sequestration; 2000 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assuming the dissolution/sequestration of CO2 at the medium-depth sea area around Japan (depth: 1,000-2,000m), the development was being proceeded with of the assessment technology for capacity of CO2 ocean sequestration and the prediction technology of environmental effects at the point of CO2 discharge. In FY 2000, conducted were the ocean survey and the development of assessment technology for CO2 sequestration capacity. In the investigational study, the following three were carried out: 1) survey/observation of the flow field on the line of 165 degrees of east longitude, and acquisition of various data such as the distribution of carbonic acid base substances and the speed of carbon transport; 2) study of the amount of existence of organisms and kind/composition of the medium-depth plankton at the typical observation points; 3) test/experiment actually conducted in the sea area for the experimental equipment for CaCO3 dissolution experimental equipment for studying interactions between the CO2 and CaCO3 dissolved into the medium-depth sea. As to the development of the assessment technology, carried out were the heightening of accuracy of medium-depth ocean circulation models using the inverse method already developed and the estimation of the flow field using the observation data. At the same time, the estimation of the flow field, etc. were conducted using large circulation ocean models. (NEDO)

  12. Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. Ocean surveys and development of a technology to evaluate CO2 separation capability; 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO{sub 2} kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Assuming that CO2 is dissolved and separated in the middle layer in a sea area around Japan, ocean surveys were carried out to acquire fundamental data required for development of a technology to evaluate CO2 separation capability of ocean, and for development of a technology to forecast environmental effect. In addition, using the western part of the Pacific Ocean as the object, development was performed on a numerical model to forecast behavior of CO2 in ocean in the scale of several ten years to several hundred years, and evaluate capability of CO2 separation from atmosphere. The research and development items for the current fiscal year are as follows: (1) ocean surveys, (2) model development, and (3) surveys and studies required for the ocean surveys and experiments. The survey voyage for item (1) was executed centering on the courses of traverse on 140 degree line of east longitude and 147 degree line of east longitude. The voyage surveyed densities of sea water, such data as chemical tracers, discharged mid-layer neutral buoys, carbonic acid based substances, marine living organisms, and sedimentary particles. For item (2), trial calculations were performed by using an inverse model to estimate structures of ocean flows, and discussions were given to enhance the accuracy. For item (3), design and fabrication were carried out on an equipment to experiment on-site dissolution of calcium carbonate, and a chamber for on-site experiments at deep sea bottom. (NEDO)

  13. Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology (putting of related data into order); 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka (Kanren data no seibi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research and development has been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of the small photovoltaic power generation system for residential use. This paper describes the actual state survey data related to grid connection systems for the small photovoltaic power generation system for residential use. The survey has been performed mainly on the system for individuals' use inside and outside Japan with regard to the small grid connection systems of 1-10 kW scale. The number of survey has reached 216 cases for 46 prefectures in Japan (1,004.02 kW in total), and 47 cases for 13 other countries (205.60 kW in total), or 263 cases in grand total (1,209.63 kW). These 263 cases were tabulated with items of owners (or the facility names and installation locations) as seen by territories (prefectures or countries), facility operators (or executing organizations), connection modes, and power generation scales. These data will serve for discussions on the load leveling effect and the optimized system forms. (NEDO)

  14. Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Tests and researches have been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of designs of the small photovoltaic power generation system for residential use. This paper summarizes the achievements in fiscal 1997. The current fiscal year has performed the continued collection of data of the demonstration operation, and analysis and evaluation on the photovoltaic power generation characteristics and the house load characteristics. According to the data analysis result for fiscals 1995 through 1997, it was shown that, although the photovoltaic power generation system for residential use does not contribute much to load leveling in a house, it contributes to load leveling in the distribution line on the whole or a case as large as a grid. In addition, according to the survey on users who have installed the photovoltaic power generation system, it was indicated that the consciousness of electric power and energy conservation has heightened. The capacity of a photovoltaic power generation system for residential use is 3 kW for a standard type of home, which can take care of more than 60% of the house load. It was concluded that, if a storage battery of small capacity is accommodated, the system is effective for reduction of momentary peak load, enhancement of the power quality, and supply of power at a disaster. (NEDO)

  15. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  16. FY 2000 report on the research cooperation project - Research cooperation in developmental support for oil producing countries. Production of catalyst and development of the evaluation technology in Kuwait; 2000 nendo san'yukoku kaihatsu shien kenkyu kyoryoku jigyo seika hokokusho. Kuuweto ni okeru shokubai seizo oyobi hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    For the purpose of strengthening the economic infrastructure of Kuwait and also strengthening the relation between Japan and Kuwait by bringing up the catalyst production industry in Kuwait as one of the key industries, the research cooperation was made with Kuwait Catalyst Co. (KCC). In this research cooperation project, the following were conducted: survey of the catalyst production environment in Kuwait, survey of the actual condition of oil factories in Kuwait and the Middle East, trial production of the catalyst to meet the needs of Kuwait, evaluation of the catalyst suitable for oil factories in Kuwait and the Middle East and evaluation of the application conditions, development of technology for production/evaluation/application of the catalyst to meet the needs of Kuwait, etc. As to the trial catalyst production at KCC, the trial products for heavy oil desulfurization and light oil desulfurization stood comparison with the catalysts produced in Japan. KCC started trial operation in fall 2000, and the commercial production is smoothly continuing. In September 2001, the catalyst for heavy oil desulfurizer of KNPC, user, was delivered. The delivery to other users was also planned to be made. (NEDO)

  17. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 1. Research study on integrated evaluation and development plan; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on the WE-NET project in fiscal 1996. The WE-NET project is composed of various elemental technologies such as hydrogen production, transport, storage, low-temperature material, utilization and hydrogen combustion turbine. The organic integrated cooperation and coordination between individual subtasks are indispensable for effective promotion of the project and optimization of the total system. The current R and D states of every elemental technology were surveyed, and its findings were utilized for coordination of the whole project and examination of the research project including pilot studies. Eleven important items in the total coordination including a total system cost and safety measures in a developmental stage were examined. The development results for 4 years of fiscal 1993-1996 were assessed together, and the draft working plan for fiscal 1997-1998 was also decided. The verification test plan of a hydrogen combustion turbine scheduled in Phase II was studied, and the basic plans of development step were proposed. The draft report of a transition scenario was also prepared. 6 figs., 68 tabs.

  18. Worldwide clean energy system technology using hydrogen (WE-NET). subtask 8. Research and development of hydrogen combustion turbines (evaluation of the optimum system); Suiso riyo kokusai energy system gijutsu (WE-NET). subtask 8. Suiso nensho turbine no kenkyu kaihatsu (saiteki system no hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Based on the proposed cycle of each contractor, conceptual design of 500 MW class hydrogen combustion turbine power generation plant has been completed through its economic examination. The optimum system has been evaluated on the basis of the conceptual design. For the conceptual design of power generation plant, the gross power generation efficiencies based on HHV of topping regenerating cycle and new Rankine cycle proved to be 61.8% and 61.7%, respectively, which exceed the target efficiency 60%. Economic consideration proved that the construction cost of each cycle will be as the same as that of the current combined cycle power generation plant. The development problem, development step and development cost have become clear. Examination on the reliability proved that the operation reliability of each cycle will be as the same as that of the current combined cycle power generation plant. Examination on the plant layout proved that the conservation of space for each system will be smaller than that of current combined cycle power generation plant. Environmental examination confirmed that each system is very clean power generation system. For the evaluation proposed by each company, the total points of each system became in the order, topping regeneration cycle, new Rankine cycle, and Rankine cycle with reheat and recuperation. 112 figs., 44 tabs.

  19. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  20. Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

  1. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  2. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  3. Achievement report for fiscal 2000 on the phase II research and development for the hydrogen utilizing international clean energy system technology (WE-NET). Task 1. Investigations and researched on system assessment; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-1. Technologies drawing attentions relate to fuel cell driven automobiles and hybrid automobiles in the field of utilizing hydrogen derived from reproducible energies and fossil energies, and fuel cell co-generation and micro gas turbine co-generation in the field of electric power generation. Hydrogen reformed from gasoline on board the automobile as the fuel for fuel cell driven automobiles, hydrogen as a by-product of coke furnace off-gas (COG), and reproducible energy hydrogen have the same fuel consumption performance as in the hybrid automobiles. Particularly the COG is low in cost, and has large supply potential. Liquefied hydrogen is as promising as compressed hydrogen in view of the cost for automotive hydrogen supply stations. What has high economic performance as the self-sustaining systems for islands are photovoltaic and wind power generation, and the system using hydrogen as the secondary energy. Since much of the reproducible energies is used for electric power demand in Japan, the by-product hydrogen and the reformed hydrogen in an amount of 9.3 billion Nm{sup 3}/year would take care of majority of the demand in view of the short time period. For a longer time span, hydrogen originated from the reproduced energies in the Pan-Pacific Region should be introduced. (NEDO)

  4. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

  5. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  6. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  7. Fiscal 1997 survey report. Subtask 3 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (conceptual design of the total system/city-level energy estimation and assessment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask zentai system gainen sekkei (toshi kibo deno yosoku hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 result of the study of scenarios for introducing hydrogen to the urban area. In the case of studying it in London, it was found that hythane (mixture of hydrogen into town gas) was effective, but in the case of doing in Tokyo, it was found that the scenario was undesirable because of the increasing infracost. Accordingly, another scenario was studied. It was assessed from the aspects of environmental advantages, infracosts, and potential advantageous values in urban areas associated with hydrogen utilization (hydrogen premium). It is most effective to use hydrogen as a fuel of transportation means from the aspect of environmental merits as the decrease in external cost. In Tokyo, the dependence upon electric power is large, and therefore it is attractive to introduce highly efficient fuel cells which enable the dispersed cogeneration using hydrogen. The value of hydrogen is determined by the avoidance of environmentally influential substances and the surplus generated output by fuel cells (substitution for the existing natural gas). When the high external cost can be assumed, the value of hydrogen becomes large. The paper also considered the arrangement of infrastructures in Tokyo. 187 refs., 14 figs., 18 tabs.

  8. Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 1. Survey/research for the comprehensive evaluation and developmental plan; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper described the results of the FY 1998 WE-NET project survey. WE-NET is composed of various element technologies such as hydrogen production, hydrogen transportation, storage technology, low-temperature materials, hydrogen utilization, and hydrogen combustion turbine technology. Therefore, considering the effectiveness as a total system, it is extremely important to traversally evaluate the situation of the R and D of each technology and developmental achievements and to work out developmental plans with integration, considering the effectiveness as a total system. From viewpoints of making effective promotion of the project and attempting optimization as a total system, it is necessary to make organic/comprehensive connection and adjustment among individual subtasks all the time. In this survey/research, in the case of proceeding with the above-mentioned studies, a committee having knowledgeable persons and learned persons as members was established. There, an investigational study was conducted over the whole WE-NET structural technology, and at the same time the following were attempted: the constant/mobile comprehensive adjustment of the whole project, evaluation of the developmental results, and optimization of the developmental plans. The results obtained in 6 years of Period I were evaluated traversally and comprehensively, and how to proceed with the development in Period II was proposed, which showed the developmental continuity. (NEDO)

  9. Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Tests and researches have been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of designs of the small photovoltaic power generation system for residential use. This paper summarizes the achievements in fiscal 1996. The current fiscal year has performed collection of data of the demonstration operation, checked the consistency in photovoltaic power generation characteristics, and housing and distribution line load characteristics, and the results were mounted on the database. The demonstration operation data were used to analyze and evaluate the facility utilization rate in the photovoltaic power generation, photovoltaic power generation dependence of the house load, load rate, and peak load reduction rate. As a result, it was found that not much of the peak load reduction effect by the photovoltaic power generation was recognized because the house load is related mainly on lighting load. However, as seen from the distribution line load, the peak load reduction was recognized when the house load and the commercial and industrial load are mixed, whereas it was revealed that the reduction effect is worth evaluation. (NEDO)

  10. FY 2000 report on the results of the infrastructure construction project for spreading high-efficiency fuel cell systems/development of test apparatuses for evaluation of fuel cell systems for automobiles; 2000 nendo kokoritsu nenryo denchi system kiban gijutsu kaihatsu / jidoshayo nenryo denchi system hyoka shiken sochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project studies the testing/evaluation methods for spreading fuel cells for automobiles. Described herein are the FY 2000 results. The problems involved in evaluation of the single cell units are classified into those involved in the cell construction and methods of evaluating the operation performances of the single cell units. These problems are analyzed mainly by literature survey. The mode simulation tests will be greatly simplified, if the system can be tested on the bench without being actually boarded on the vehicle. Therefore, this project is aimed at development of a comprehensive mode simulator which can be automatically operated corresponding to the running modes of various countries, to test the performance of FCEV and to examine the effects of each component independently on the vehicle performance. The factors required to reproduce the actual driving states of an FCEV on the bench are analyzed, and the conceptual designs are drawn for the controlling algorithms. It is necessary to standardize the stack and reformer testing methods, in order to evaluate the fuel cell system components. For these objects, the prototype units are constructed to evaluate 10kW direct hydrogen type stacks and 5kW methanol reformers. The units are also constructed to evaluate the high-pressure (1MPa) reformer reactors and hydrogen separation membrane systems. (NEDO)

  11. Fiscal 1998 research report. Survey on the evaluation and factor of the competitive power of industrial technologies in various fields including an electronic field; 1998 nendo chosa hokokusho.Denshi kanren nado wo hajime to suru sangyo gijutsu kyosoryoku no hyoka to yoin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made to evaluate the Japanese competitive power of industrial technologies, and analyze inhibitors from its development by extracting some issues for improvement. Questionnaire survey was made for learned persons based on the framework on evaluation of the Japanese technical level. The current Japanese level of each technology was evaluated generally comparing it with that of overseas countries to acquire its strong and weak points. Based on the hearing for learned persons, the industrial competitive power was evaluated freely from technology, and issues of every industry were also extracted. Problems existed in not only a technical level but also an undertaking process, and based on these problems, the competitive powers of every industry were classified. Previous proposals on the competitive power were analyzed based on literature survey to arrange some policies to approach. Possible inhibitors were arranged showing the policy reinforcing the industrial competitive power. Problems on educational system, business management, social infrastructure, and technology diffusion system were extracted. (NEDO)

  12. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  13. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  14. Achievement report for fiscal 1990. Research and development of ceramic gas turbine (Development of test and evaluation methods for ceramic member bonding technology); 1990 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Development of test and evaluation methods has been performed on a technology to bond ceramics with metals from the viewpoint that what governs bonding is residual stress. Activities were made in the following three fields: 1) tests and researches, 2) analytical studies, and 3) studies on correlation of residual stress with strength characteristics. In Item 1, selections were made on Si{sub 3}N{sub 4} as the ceramics, ordinary steel as the metal, and the brazing process in vacuum using Ti-based active metal as the bonding method. Discussions were given on processing of test pieces and the procedure thereof, an X-ray stress measuring method, a non-destructive inspection method, and a strength testing method. In Item 2, discussions were given on analysis of the bonding method and the residual stress in the bonding material due to brazing of ceramics with metal, for example, and the effects of the cutting process on the residual stress. In Item 3, discussions were given on mechanical strength evaluation on the bonding materials including the processing defects, for example, with regard to the correlation of the bonding residual stress with the mechanical strength characteristics, and on the effects of the residual stress on the tensile strength. (NEDO)

  15. Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which IEA international cooperation project; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi IEA kokusai kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper summarizes the activities related to the Annex II 'Communication technology for DSM' in the international cooperation agreement on the DSM program by IEA. With regard to the 'needs in relation with DSM and the related functions and the communication technology between the demand side and the electric power companies required for the execution thereof', a survey has been made by sending question letters to ten membership nations, which has been compiled into a report. With respect to the 'evaluation on the method for international cooperation on standardization of the communication technology', replies to the question letters from the membership nations were analyzed. Decisions were given on the standards directly related to the communication technology for DSM, the standard drafting organizations, and the working groups. With regard to the 'evaluation on priority on research, development and demonstration of the communication technology for DSM', propositions were given as the project on the technology for communications inside a building for DSM and the related functions, development and transfer of DSM and the related functions from the communication media for a narrow band to a wide band, and specifications for the customers' terminals. In developing the general purpose personal computer software 'eaCOMMS', distribution and discussions were given on the trial edition. (NEDO)

  16. Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology (putting of related data into order); 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka (Kanren data no seibi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research and development has been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of the small photovoltaic power generation system for residential use. This paper describes the actual state survey data related to grid connection systems for the small photovoltaic power generation system for residential use. The survey has been performed mainly on the system for individuals' use inside and outside Japan with regard to the small grid connection systems of 1-10 kW scale. The number of survey has reached 216 cases for 46 prefectures in Japan (1,004.02 kW in total), and 47 cases for 13 other countries (205.60 kW in total), or 263 cases in grand total (1,209.63 kW). These 263 cases were tabulated with items of owners (or the facility names and installation locations) as seen by territories (prefectures or countries), facility operators (or executing organizations), connection modes, and power generation scales. These data will serve for discussions on the load leveling effect and the optimized system forms. (NEDO)

  17. General report of entrustment investigation for demonstration tests of turnover from oil to methanol in the thermal power plants in fiscal 1995. Total assessment of methanol using power generation technology; 1995 nendo sekiyu karyoku hatsudensho methanol tenkan nado jissho shiken itaku gyomu hokokusho sokatsu hokokusho. Methanol riyo hatsuden gijutsu sogo hyoka chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To promote the introduction of methanol fuel into the thermal power plants, total assessment was provided. For calculating the methanol production cost, the plant was assumed to be constructed in the Southeast Asia or Middle East. Two methods, i.e., steam reforming and gaseous phase fluid methods, were investigated. Since the price of natural gas is low in the Middle East, the methanol production cost by the gaseous phase fluid method is estimated to be about 1.5 yen per thousand kcal. The transportation cost can be reduced into one-half to one-third of current cost using a large-scale tanker. Although the heating value of methanol per weight is lower than that of LNG, the volume flow of methanol is similar to that of LNG due to its low specific gravity. Conceptual designs were conducted for some power generation systems, such as gas turbine of combined cycle, diesel engine, and fuel cell. The power generation cost was estimated to be 8 to 9 yen per kWh, which depends on the receiving price of methanol. It is nearly equivalent to that of LNG combined cycle power generation. There are no problems of air pollution and ash disposal. When considering the long-term security of energy sources, the use of methanol would be one of the selections as utilization of natural gas. 6 refs., 33 figs., 25 tabs.

  18. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  19. Fiscal 1997 report on the investigational research on the evaluation of a global energy system as global environmental protection technology. 2; 1997 nendo chosa hokokusho (chikyu kankyo taisaku gijutsu to shite no global energy system no hyoka ni kansuru chosa kenkyu). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An energy supply system which is globally formed for global environmental protection is called a global energy system (GES), in which to achieve substantial CO2 reduction, various measures against CO2 are introduced to energy systems extending from places of fuel supply to places of fuel consumption. For the study of a scenario for introduction such a GES, it is necessary to investigate the GES presently proposed and make a traverse evaluation of it under uniform preconditions and evaluation criteria. Concretely, following a case study of evaluating performance of the GES with a power system as the final form from viewpoints of economy, energy balance, CO2 emissions, etc., the paper arranged characteristics of liquid fuel supply systems including methanol from a traverse aspect, made evaluation of performance and possibilities of the introduction in the areas concretely named, and studied positioning of this energy system, scenario for the future introduction and possibilities of the introduction from global and long-term aspects. 79 refs., 102 figs., 77 tabs.

  20. Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development project on high-speed deformation characteristics evaluation methods for metallic materials; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo. Kinzoku zairyo no kosoku henkei tokusei hyoka hoho no kenkyu kaihatsu jigyo - Gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to develop methods for evaluating the characteristics of metallic materials experiencing high-speed deformation or impact deformation. The research was conducted by the research WG (working group) consisting of some participants of an international conference convened this fiscal year. The research result revealed that studies in Japan lopsidedly dealt with metallic materials at strain velocity of 10{sup 4}/second or less, such as steel, while many studies overseas dealt with materials other than metals at strain velocity over 10{sup 4}/second. The test and evaluation WG conducted high-speed tension tests for T6-treated aluminum alloys using the split Hopkinson bar method, hydraulic servo method, one bar method, and the sensing-plate method for measuring force, and the results were compared. It was then found that the one bar method produced disturbance more remarkably than the others and that the loading block structure and load rise time influenced the emergence of the peak load. The emergence of a peak load in the Hopkinson bar method or the one bar method had been predicted on the basis of the research conducted by the analysis group. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

  2. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  3. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  4. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  5. Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research and development has been performed with the objectives to establish an evaluation technology for load leveling effect by using a small photovoltaic power generation system for residential use, to clarify the effectiveness of the system as a discrete power supply source through demonstration operation, and furthermore to achieve optimization of the small photovoltaic power generation system for residential use. This paper summarizes the achievements in fiscal 1995. With the demonstration operation in the current fiscal year, through-the-year data have been accumulated for the first time since the start of the demonstration operation, and were mounted on the load leveling database. As a result of analyzing the demonstration operation data, the following points were revealed: regarding the housing load, the lighting load is the main factor both in summer and winter; the effect of reducing the peak load by photovoltaic power generation is recognized at about 60% as maximum, but the substantial effect has large variation, hence stochastic; and the reverse current becomes the main factor during daytime, not necessarily leading to improvement of the housing load characteristics in the aspect of load rate. According to the surveys on the energy demand trends up to the year 2030, the power supply configuration, and introduction cost, it was revealed that the photovoltaic power generation can be sufficiently expected as a power supply to handle the peak load. (NEDO)

  6. Fiscal 1998 research report on International Clean Energy Network using Hydrogen Conversion (WE-NET). Subtask 3. Prediction evaluation on a national scale; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) sub task. 3. Ikkoku kibo deno yosoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japanese long-term energy demand and various energy use styles were simulated from the viewpoint of a profitability and environmental preservation, and hydrogen consumption was studied. In the research in fiscal 1998, the data on available primary energy was modified based on the upper limit of CO{sub 2} emission by COP3, and the long-term energy supply and demand outlook of Advisory Committee for Energy in June, 1998. The result of scenario analysis is as follows: (1) The reference scenario showed that reduction of a hydrogen price is indispensable to use imported hydrogen, (2) The carbon externality scenario showed that market penetration of hydrogen can be large if the carbon externality amounts to $300/t-C, (3) The high fossil fuel price scenario showed that a fossil fuel price (in particular, price of hydrocarbon) highly affects market penetration of hydrogen, and (4) The low nuclear capacity scenario suggested that a competitiveness of hydrogen is considerably improved as an energy supply-demand-balance is tight. (NEDO)

  7. Fiscal 1997 survey report. Subtask 3 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (total system/nation-level energy estimation and assessment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 3 zentai system ikkoku kibo deno yosoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With relation to the energy supply/demand in Japan toward the second half of the 21st century, an analysis was made using the MARKAL model to predict the amount of hydrogen introduction in the future. As in the last fiscal year, conditions of the study of IEA/ETSAP were continuously used. It was decided on that hydrogen was produced by hydroelectric/photovoltaic power generation overseas. Prices were made 14 yen and 27 yen/103 kcal. The limit price of introduction of import hydrogen was calculated. During the period from 2030 to 2050, if the hydrogen price is less than 7 ten/103 kcal, the result showed that hydrogen can be introduced in a lot of scenarios (case of the severe control of CO2 emissions, case of high priced fossil fuels, case of the low capacity of the development of nuclear power generation, etc.) As the form of hydrogen use, promising are the hydrogen combustion turbine power generation, mixture with town gas (hythane) and hydrogen cars. However, a precondition for the introduction is that the cost of hydrogen car should be more economical than the competitive means of transportation. As to hydrogen combustion turbines and hythane, the quantity of hydrogen introduction depends little on variations of characteristics of the equipment used. 11 refs., 55 figs., 21 tabs.

  8. Report on the surveys in fiscal 1999 on the long term energy technology strategy investigations. Investigations on evaluation on impact of research and development investments, and optimal resource distribution; 1999 nendo choki energy gijutsu senryaku chosa hokokusho. Kenkyu kaihatsu toshi no impact hyoka oyobi saiteki shigen haibun ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper is a survey report for fiscal 1999 related to investigations on evaluation on impact (influential effect) of research and development investments, and on optimal resource distribution. First, a quantification analysis was performed on the impact imposed by the New Sunshine Project having been executed in the past. The analysis used as the base the regressive analysis between the project techno-stock (an index of the project budget amount depleted by a certain obsoletion rate after having been substantiated and aggregated) and the number of theses. In a case where time-series data can be obtained on the quantity of practical application, the regressive analysis was also performed between the number of theses and the quantity of practical application. A large number of projects are stimulating research and development activities of the subject themes of all about Japan. Some are imposing great influential effect on the practical application. In addition, it was found that emphasized and concentrated investment cases in the initial stage of a project have high influential effect. As a budget distribution pattern, the concentrated and emphasized investments in the initial stage of a project are more effective than investing dispersedly over an extended period of time. Suggestions were acquired on the future budget distribution. (NEDO)

  9. Achievement report for fiscal 1989. Research and development of ceramic gas turbine (Development of test and evaluation methods for ceramic member bonding technology); 1989 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-05-01

    Development of test and evaluation methods has been performed on a technology to bond ceramics with metals as a support to develop a ceramic gas turbine (CGT), from the viewpoint that what governs bonding is residual stress. Activities were made in the following three fields: 1) investigative studies, 2) tests and researches, and 3) analytical studies. In Item 1, literatures were investigated, and research plans were established with regard to residual stress. Selections were made on Si3N4 as the ceramics, ordinary steel (S45C) as the metal, butt joint bonding of flat plates with each other as the bonding method, X-ray stress measuring method and IF method (semi-destructive test) as the residual stress measuring methods, and the finite element method as the analytical method. In Item 2, bonded test pieces were made, and the residual stress measuring test was performed to discuss the test and evaluation methods in relation with the bonding patterns and adaptability of the bonding. In Item 3, basic discussions were given on applicability of the residual stress analysis method using the finite element method, and on analysis of the affecting factors and modeling. (NEDO)

  10. Achievement report for fiscal 1991. Research and development of ceramic gas turbine (Development of test and evaluation method for ceramic member bonding technology); 1991 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-05-01

    Development has been made on the test and evaluation method for a technology of bonding ceramics with metals from a viewpoint that what governs the bonding is residual stress. Activities were made on 1) test researches, 2) analysis researches, and 3) researches on the correlation of residual stress with mechanical strength characteristics. In Item 1, tests on the bonding residual stress and mechanical strength characteristics, tests on high temperature mechanical strength characteristics, X-ray stress measurement, IF method measurement, and mechanical strength test were performed. In Item 2), researches were made on three-dimensional stress analysis of interface bonded with different materials, high temperature mechanical strength of bonded bodies, and heat cycle fatigue strength. In Item 3, destruction dynamic discussions were given on the effects of the residual stress on the tension rupture strength, and cracks on bonded interface. Specifically speaking, residual stress in four kinds of bonded bodies with various sizes (Si{sub 3}N{sub 4}/Cu/steel), for example, was measured, the bonded bodies were subjected to a cutting process, and considerations were given on the effects imposed on re-distribution of the residual stress due to the cutting and on the bonding strength. (NEDO)

  11. Report on the FY 1999 results of the development of the wide area energy utilization network system - Eco/energy urban system. 2/2. Study of the systematization technology/evaluation technology out of the study of the energy system design technology (Study of the application method of element technology/system and trial calculation of the introduction effect); Koiki energy riyo network system kaihatsu (eco energy toshi system). 2/2. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu 1999 nendo seika hokokusho (zenkoku no netsu juyo no bunpu jokyo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of smoothly introducing the equipment technology and system technology being studied in the development of element technology in the eco/energy urban project, the paper conducted the study of conditions/application method in applying the technology to the actual energy supply system, analysis of the introduction effect, arrangement of the subjects on technical development, etc. In the study, for the methanol/hydrogen base technology, heat pump technology, heat recovery technology, heat transport technology and heat power generation technology, the quantitative analysis was made in terms of the lifecycle energy consumption amount, lifecycle CO2 emission amount and lifecycle expenses. As to the methanol base system, the subject is the reduction in auxiliary power. Concerning the heat pump technology, the subject is the enlargement of simple equipment. As regards the heat recovery technology, the subject is the development of system with long useful year. Relating to the heat transport technology, subjects are the completion of the menu of large-diameter piping in the vacuum thermal insulation heat transport piping system, and reduction in conveyance power of heat medium. About the heat power generation technology, subjects are the stability/durability of the system. (NEDO).

  12. FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D on the improvement of reliability of photovoltaic power generation - Investigative study of long-term reliability of inverter - Separate volume: Data on the life evaluation test); 2000 nendo New sunshine keikaku seika hokokusho(Sokatsu ban). Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Taiyokohatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - Inbata no choki shinraisei no chosa kenkyu - Bessatsu : Jumyo hyoka shiken datashu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of establishing a life evaluation method for power conditioner of about several kilowatts for general housing use, the acceleration test was made, and the data were summarized for maintenance of power quality, cooperation with the protection system at power system, insuring of safety of personnel/facilities, etc. As to the acceleration method, by paying attention to heat deterioration of thermal plasticity materials being used for power conditioner and by using the acceleration method using the 10-degree C half law by the Arrhenius law, temperature and humidity were set at 40 degrees C and 36%, respectively. The operation hour and stopping time were fixed at 3.5 hours and 4.5 hours, respectively. The life evaluation measurement by the acceleration test was composed of the continuous evaluation measurement with the aim of early finding the degradation of performance, anomaly, etc. of power conditioner and of the evaluation measurement at specified intervals with the aim of precisely measuring the state of degradation of power conditioner. As a result of the continuous evaluation measurement, the paper reported the data on the rise in temperature inside the power conditioner during the acceleration test and the change in electric characteristics of input/output. (NEDO)

  13. FY 2001 report on the integrated evaluation of the research cooperation project. Research cooperation program on the development of environmental measurement use laser radar/research cooperation project on the mining waste water treatment technology using biology; 2001 nendo kenkyu kyoryoku jigyo sogo hyoka hokokusho. Kankyo kesokuyo reza reda no kaihatsu ni kansuru kenkyu kyoryoku - Baio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    By research groups having been sent, the integrated evaluation was made of the projects on the research cooperation with Indonesia in the development of environmental measurement use laser radar and the research cooperation with China in the mining waste water treatment technology using biology. As to the research cooperation with Indonesia, the purpose/target proposed were almost achieved, and all were favorably carried out. Especially, after finishing the project, the design/manufacture of an on-vehicle type Mie-scattering laser radar were made using the acquired laser technology. And, it was reported that an observation study of the state of air pollution in Bandung city was made using the laser radar. It can be said that generally the research cooperation with China was smoothly proceeded with. However, the Wushan mine is small in scale of management, and therefore, there might have been some points to be reviewed in selection of the mine for research. The pilot plant installed at the Wushan mine is not now operated. If the mine has strong management force, the effective use of the pilot plant after finishing the project might have been studied. (NEDO)

  14. Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

  15. Chromatic regulation in cyanobacterium as studies by HPLC quantitation of photosynthetic pigments. Kogosei shikiso no HPLC teiryo ni motozuku ranso no hikari tekio process tsuiseki

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, H.; Watanabe, T. (The Univ. Tokyo, Tokyo (Japan). Inst. of Industrial Science)

    1991-08-01

    Plants higher than Cyanobacterium have two kinds of resction centers(RC) which convert photon energy to a flow of electrons and whose photosensitive spectral regions are slightly deviated from each other. In the photosynthetic process, the ratio of numbers between these two kinds of reaction centers is adaptively varied so as to allow the overall flow of electrons to proceed in a well-balanced manner. It is important to rapidly and exactly determine the ratio of RC numbers between the two photochemical systems in order to investigate such photoadaptive process. The report describes the quantitative determination using high performance liquid chromatography(HPLC) for this purpose. Pigments were extracted from Cyanobacteria which are in different adaptive processes brought by being cultured in the environments differing in the quantity of light or in the environment of varying quantity of light, and subjected to quantitave determination in consideration of the fact that the reaction centers, I and II, have the respective special kinds of chlorophyl derivatives Chl-a, Chl-a{prime}. As the results, it was confirmed that validity can be given to the estimation of the numbers of reaction centers in terms of the quantities of Chl-a and Chl-a prime and the proposed method is drastically faster and simpler than the conventional methods. 14 refs., 5 figs..

  16. Dynamics of hydrogen induced blistering of a low carbon steel sheet by lamb waves analysis; Ramuha no teiryo kaiseki ni yoru hakubanteitansoko no suiso hare no dainamikkusu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Teruyoshi.; Takemoto, Mikio. [Aoyama Gakuin University, Tokyo (Japan). Faculty of Science and Engineering

    1999-06-15

    With the aim of studying the fracture dynamics of environmentally assisted fractures in thin plates, we developed a new source simulation method of the zeroth-order symmetric (or S{sub 0}-) Lamb wave using the experimental overall-transfer function of the system. The transfer function was determined by the time-domain deconvolution of detected S{sub 0}-Lamb component by the artificial fracture source of a compression -type PZT element whose vibration kinetics was estimated by the iteration so that the S{sub o}-waveform detected. Hydrogen induced blistering was found to be caused by the succession of fast Mode-I fracture with source rise times from 0.6 to 1.0{mu}s. The crack volume estimated by the source simulation corresponded to that of fine blistering with an opening displacement of 5{mu}m. As the estimated fracture kinetics of hydrogen blistering coincide with those of delayed fracture of high tension low alloy steel under tensile loading, the kinetics of first and micro-fractures and blistering induced by hydrogen gas precipitation appears to be independent on the hydrogen solubility and strength of steels, the applied stresses and the orientation of cracks. (author)

  17. Evaluation method of offensive odor. Shuki no hyoka hoho

    Energy Technology Data Exchange (ETDEWEB)

    Iwasaki, Y [The Tokyo Metropolitan Research Institute for Environmental Protection, Tokyo (Japan)

    1991-06-01

    As the evaluation method of offensive odor, two kinds of methods were outlined, a concentration measurement method for compounds emitting offensive odors and a sensory method by human olfactory organ. On the former, the method for measuring separately odors of twelve compounds controlled by the regulation act such as ammonia and hydrogen sulfide was outlined as well as the method for measuring odors of compound groups such as total reduced sulfur and total hydrocarbon. On the later, the evaluation scale of essential properties of odor such as quality, intensity, acceptability and pervasiveness was discussed. As typical sensory techniques, a scentometer, syringe method, odorless chamber method and olfactometer were outlined, and a triangle odor bag method widely used for the evaluation at present was described in detail which was developed to reduce demerits of a syringe method such as adsorption of odorants on a syringe surface. 24 refs., 6 figs., 3 tabs.

  18. Quantitative analysis of sulfur forms of coal and the pyrolysis behavior of sulfur compounds; Sekitanchu no io kagobutsu no keitaibetsu gan`yuryo no teiryo to sono netsubunkai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Mae, K.; Miura, K.; Shimada, M. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-28

    As part of the studies on coal utilization basics, considerations were given on quantification of sulfur forms of coal and the pyrolysis behavior of sulfur compounds. With the temperature raising oxidation method, a thermo-balance was connected directly to a mass analyzer, and the coal temperature was raised at a rate of 5{degree}C per minute and gasified. Peak division was performed on SO2 and COS production to derive sulfur forms of coal. Using the slow-speed pyrolysis method, production rates of H2S, COS, SO2 and mercaptans were measured at a temperature raising rate of 20{degree}C per minute. Sulfur content in char was also measured. With the quick pyrolysis method, a Curie point pyrolyzer was connected directly to a gas chromatograph, by which secondary reaction is suppressed, and initial pyrolytic behavior can be tracked. All kinds of coals produce a considerable amount of SO2 in the slow-speed pyrolysis, but very little in the quick pyrolysis. Instead, H2S and mercaptans are produced. Sulfur compound producing mechanisms vary depending on the temperature raising rates. By using a parallel primary reaction model, analysis was made on reactions of H2S production based on different activation energies, such as those generated from pyrite decomposition and organic sulfur decomposition. The analytic result agreed also with that from the temperature raising oxidation method. 4 refs., 6 figs., 1 tab.

  19. Determination of sup 238 U in marine organisms by inductively coupled plasma mass spectrometry. Yudo ketsugo plasma shitsuryo bunsekiho ni yoru kaiyo seibutsuchu no sup 238 U no teiryo

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, T.; Nakahara, M; Matsuda, M.; Ishikawa, M. (National Institute of Radiological Sciences, Ibaraki (Japan))

    1991-05-25

    Since the {sup 238} U concentration in seawater is about 3ng/ml at the element level and the activity concentration is 40 {mu} Bq/ml which are considerably higher that those of other {alpha} radioactive materials, it is necessary to study the concentration levels of many marine organisms. After confirming that the inductively coupled plasma mass spectrometry as a new high sensitive analysis for multi-elements is effective to analyze heavy elements such as rare earth elements or uranium, etc., this method was applied to determine {sup 238} U in 55 species of marine organism. The {sup 238} U concentration in soft tissues of marine animal ranged from 0.076 to 5000ng/g wet weight and large difference of concentration was observed depending on the kind of animal and the tissue. Especially, the branchial heart of cephalopod molluscs showed the specific accumulation of {sup 238} U. The concentration factor of branchial heart of Octopus vulgaris which showed the highest value was calculated to be about 10 {sup 3} by comparing it with the concentration of {sup 238} U in Japanese coastal waterseas. The concentration of {sup 238} U in 20 species of algae ranged from 10 to 3700ng/g dry weight. 11 refs., 2 figs., 9 tabs.

  20. Fiscal 1999 international cooperation project report. Development of high-precision quantitative analysis technology for catalyst surfaces by electron spectroscopy; 1999 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki bijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project targets to make analysis of surface chemical phenomena of solid catalysts possible, and establish the basis of intelligent design for catalytic materials, through development of an advanced electron spectroscopy for surface analysis. In fiscal 1999, the research was promoted by using the diffraction grating and driving mechanism introduced in fiscal 1998, and by developing the measurement result on silicon oxide films by radiation beam photoelectron spectroscopy. The measurement technique was established by the optimized measurement process which can treat variable parameters as constant. The analysis result of measurement data in fiscal 1999 showed the dependence of an electron damping length in silicon oxide films on radiation photon energy. The energy dependence well agreed with a theoretically obtained inelastic mean free path of electrons qualitatively, while was smaller by nearly 30% than the latter quantitatively. Measurement was made on the damping length in oxidation-active Gd and Nd oxide films. In both cases of Si and Si oxide film substrates, oxidation of substrates or formation of silicate was observed. (NEDO)

  1. Introductory asphalt technology; Nyumon asphalt gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Muroga, G. [Mitsubishi Oil Co. Ltd., Tokyo (Japan)

    1994-12-28

    The type and applications, manufacturing method, characteristics, road pavement etc. of asphalt were introduced. Among the petroleum asphalts, straight asphalt is used for road pavement,industry, and combustion, while blown asphalt is mainly used for the waterproofness of a building. Also, the demand for modified asphalt where rubber or thermoplastic elastomer was mixed is increasing. Straight asphalt is obtained by allowing atmospheric distillation tower bottom oil to be subjected to reduced pressure distillation and drawing reduced pressure gas oil and lubrication oil cut. Blown asphalt is produced by the oxidation dehydrogeneration and condensation polymerization reaction of soft straight asphalt. Rheology characteristics of asphalt are expressed by stiffness, relaxation elastic modulus, complex elastic modulus, etc. Also, asphalt has high electrical dielectric properties. Asphalt pavement has functions for dispersing traffic load and then transferring it to a lower layer, for resisting wear and cracking, and for preventing penetration of rainwater. 30 refs., 5 figs., 4 tabs.

  2. Evaluation for membrane components of water recycling system. Mizu saisei junkan system yoso no tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Tanemura, T; Otsubo, K; Oguchi, M [National Aerospace Laboratory, Tokyo (Japan); Ashida, A; Hamano, N; Mitani, K [Hitachi, Ltd., Tokyo (Japan)

    1992-04-01

    The configuration of water recycling systems with membrane filters was studied to purify waste water discharged from human beings, animals and plants which is a key subsystem for closed ecological life support systems (CELSS) essential to long-term manned space activity. The filter performance test apparatus with three kinds of filters such as pre-filter, reverse osmosis membrane filter and ultra membrane filter was fabricated to conduct long-term cycling high-concentration tests using artificial urine as original waste water. As a result, since every membrane filter offered their nominal performance incompletely in high-concentration tests, it was necessary to add an NaCl removing apparatus to the system as primary treated water should be used for vegetation. It was also required to test the membrane performance preliminarily because the performance such as membrane life was different between various waste waters. 7 refs., 32 figs., 9 tabs.

  3. Evaluation of PV modules integrated with roofing materials; Kenzai ittaigata taiyo denchi module no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Morizane, M.; Yagiura, T.; Nakashima, S.; Yagi, H.; Murata, K.; Uchihashi, K.; Tsuda, S.; Nakano, S. [Sanyo Electric Co. Ltd., Osaka (Japan); Ito, M.; Kurimoto, T.; Yamakawa, H.; Fujiwara, T. [Kubota Corp., Osaka (Japan)

    1997-11-25

    PV modules unified with building materials which are low in cost, easy to install and excellent in designing were developed and were evaluated in various tests. As to the basic structure of this module, seamless and unified construction with the back metal plate was adopted considering improvement in fire prevention and cost reduction. About the installation, module is easy to install by just fit connection with the frame, and easy to remove with no use of special tools. Concerning intensity and durability requested for this module, tests on reliability such as torsion strength and wind pressure resistance were conducted according to JIS standards, and it was confirmed that there were no problems. Also on the long-term durability, tests on long-term reliability were carried out by doubling test terms of the temperature/humidity cycle test, salt water resistance test, etc., and the reliability the same as that of the existing type was confirmed. In the verification test using a model house, no changes were seen in electrical characteristics and appearance, and waterproof was also favorable one and a half year after the installation. 4 refs., 7 figs., 5 tabs.

  4. Geothermal reservoir assessment manual; 1984-1992 nendo chinetsu choryusou hyoka shuhou manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-02-01

    A geothermal reservoir assessment manual was prepared for the promotion of the development of geothermal power generation, based on the results of the 'geothermal reservoir assessment technique development project' implemented during the fiscal 1984-1992 period and on the results of surveys conducted in Japan and abroad. Of the geothermal systems generally classified into the steam dominant type and the hot water dominant type, encounters with the steam dominant type are but seldom reported. This manual therefore covers the hot water dominant type only. In addition to the explanation of the basic concept and the outline of geothermal reservoirs, the manual carries data necessary for reservoir assessment; geological and geophysical data analyses; geochemistry in reservoir assessment; data of underground logging and of fuming; conceptual models; simulators and models for reservoir simulation; natural-state simulation, history-matching simulation, and reservoir behavior predicting simulation; case history (modeling of a geothermal reservoir prior to exploitation), references, and so forth. (NEDO)

  5. Evaluation of environmental impact by LCA method. LCA shuho ni yoru kankyo fuka hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Sakamura, H.; Utsuno, F.; Yasui, I. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1994-06-01

    This paper explains the concept, history, and analytic methods of life cycle assessment (LCA), showing its application to beer bottles and cement factories as specific examples. The LCA is a method to calculate substances and energies put into the whole process of production of a product from raw material mining to product wasting and environmental loads emitted therefrom. It also evaluates the result collectively and quantitatively. A first case of the research is reportedly the one performed at Coca-Cola Co., Ltd. in 1969. Full-scale researches have gone forward in European countries in the recent several years, and are progressing to international networks. The analytic methods can be divided largely into an accumulation method to analyze data in each process and add them up, and a method to use an industrial association table. The former method is the most generally used method currently in overseas countries if referred to the LCA. Because the LCA can cause the analytic result and evaluation to vary depending on the purpose, it is important to define the goal, and set the scope. The LCA must develop in the future although it has a number of problems. 10 refs., 5 figs., 2 tabs.

  6. Geothermal reservoir assessment manual; 1984-1992 nendo chinetsu choryusou hyoka shuhou manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-02-01

    A geothermal reservoir assessment manual was prepared for the promotion of the development of geothermal power generation, based on the results of the 'geothermal reservoir assessment technique development project' implemented during the fiscal 1984-1992 period and on the results of surveys conducted in Japan and abroad. Of the geothermal systems generally classified into the steam dominant type and the hot water dominant type, encounters with the steam dominant type are but seldom reported. This manual therefore covers the hot water dominant type only. In addition to the explanation of the basic concept and the outline of geothermal reservoirs, the manual carries data necessary for reservoir assessment; geological and geophysical data analyses; geochemistry in reservoir assessment; data of underground logging and of fuming; conceptual models; simulators and models for reservoir simulation; natural-state simulation, history-matching simulation, and reservoir behavior predicting simulation; case history (modeling of a geothermal reservoir prior to exploitation), references, and so forth. (NEDO)

  7. Test and evaluation on safety relating to biotechnology; Biotechnology ni kansuru anzensei no shiken to hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Okada, M. [Bio-Oriented Technology Research Advancement Inst., Saitama (Japan)

    1996-09-05

    This paper describes the current status and how works are being carried out on safety tests and evaluation of gene recombinants in plants and microorganisms. In the field of plants, Flavr Savr tomato which has been improved in fully ripe fruit distribution and keeping quality was commercialized as the world`s first recombinant food in May 1994 by Calgene, Inc. of America. Other vegetables, such as soybean, corn, potato, and pumpkin have been completed of all items of safety evaluation, and are approaching the commercialization phase. The safety evaluation system for living organisms created by using recombinant DNA technologies has been established internationally with regard to its general framework and contents based on accumulated knowledeges and experiences as a result of utilization of over twenty years. Industrial utilization guidelines for recombinants in Japan have been established in correspondence with the OECD recommendation in 1986. Experiments to verify recombinants to be safe in environment, and cultivation of the recombinants for utilization are performed based on the experimental guidelines and utilization guidelines. 15 refs., 1 fig., 5 tabs.

  8. Method of evaluating the surface color of concrete; Concrete hyomenshoku hyoka shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, Y; Kotani, K; Imadate, F; Ito, N; Watanabe, K [Kajima Corp., Tokyo (Japan)

    1995-12-20

    As a part of the evaluation of landscape of civil engineering structures, a method was studied for quantitative evaluation of surface color and color hue of the exposed concrete. The surface colors of concrete structures constructed at more than one sites were measured using a colorimeter and were statistically processed. The colorimeter can measure colors by irradiating the standard light onto the surface of the object and dividing the reflection light into ingredients, lightness L and color phase a and b in the CIELAB equal color space. The L/a/b measuring data were plotted which were obtained from 2010 measuring surfaces of 49 structures at 7 construction sites. As for the surface color of concrete, it was found that ingredient L measured by the colorimeter reacts on variations of color very sensitively and agrees well with the trend of evaluation by eyes. Namely, human being senses the difference of concrete color mainly from the difference in lightness and senses the difference as the color hue. Further, using the neural network, an evaluation method was established which was the same as the human sense. 1 ref., 8 figs., 3 tabs.

  9. Effect of water pollution on marine organisms; Sekiyu osen no kaiyo seibutsu eno eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, M. [Okayama Univ., Okayama (Japan); Fujisawa, K. [Okayama Prefectural Fisheries Experiment Station, Okayama (Japan)

    1997-10-10

    Toxicity of petroleum component to aquatic organisms appears as a result of its deposition onto living organisms followed by its migration into bodies of the organisms, and emergence of toxicity from the migrated component. Effect evaluation processes standing on this viewpoint may include the exposure monitoring or migration monitoring, in which the petroleum component migrated into marine organisms is analyzed and the state of the component concentrated in these organisms is measured, or effect monitoring, in which actions of the petroleum component in the organisms are investigated. The effects of petroleum on aquatic organisms would include the following occurrence: direct fatal toxicity acting on cells and membranes, quasi-fatal toxicity causing death indirectly through feeding actions and abnormal actions, direct coating of oil on surface of organisms, which prevents movability and feeding actions of the organisms and reduces hydrophilicity of plumes and hairs, pollution of living organisms due to migration of carcinogenic aromatic compounds into bodies of the living organisms, and change in species compositions and geographic distribution of living organisms due to change in physico-chemical environment. This paper explains cases of detection and identification of organic sulfur compounds, aromatic compounds, polycyclic aromatic compounds, paraffins, olefins and heavy metals in parametric compounds of petroleum. 20 refs., 4 figs., 3 tabs.

  10. Psychoacoustic parameters and its measuring system; Onshitsu hyoka wo hyokasuru tame no parameter to keisoku system

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, M.; Imaizumi, H.; Ono, T. [Ono Sokki Co. Ltd., Tokyo (Japan)

    1998-05-01

    Human auditory sensation has both extremely excellent performance and general versatility as sound analyzer. At present, it is impossible to make equipment with the same functions as human being, and describe an auditory sensation function as acoustic sensor even by any physical analysis techniques. However, extraction of auditory sensation parameters is becoming possible by using psychoacoustics and binaural signal processing. This paper mainly explains the calculation method of sound quality evaluation parameters derived from psychoacoustic results based on a sound quality evaluation system under development by the authors. This system is based on binaural measurement by dummy head, and calculates psychoacoustic parameters such as loudness, sharpness, roughness, fluctuation strength and tonality through frequency analysis of the measured stereo signals. The system also calculates 2-D parameters such as sensory pleasantness and unbiased annoyance based on the above parameters. 12 refs., 4 figs.

  11. Exergetic evaluation on photovoltaic/thermal hybrid panel; Taiyoko netsu hybrid panel no exergy hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Iwaki, H; Morita, Y; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)

    1996-10-27

    The photovoltaic/thermal hybrid panel (PV/T) is an energy converter that was designed for the composite use of electricity and heat. In this paper, the validity of PV/T designed for trial was evaluated based on an exergetic theory. As the result of an experiment, the electric exergetic value of PV/T and PV is each 65.8 kWh/m{sup 2} and 58.6 kWh/m{sup 2}. The former is higher than the latter by 11.2%. The total exergetic value of PV/T is also 1.2 and 8.2 times as high as those of a PV and solar collector (SC), respectively. The calculation result of the optimum temperature operation showed that the exergetic value of PV/T is 3.1 times as high as the electric exergetic value. Therefore, the operation must be performed with the electric and thermal exergetic values set in a ratio of 3.1 to 1. In this paper, the operating mode is handled in which importance was more attached to the electric exergy than the thermal exergy. The flow rate of a heating medium on PV/T is not thus the flow control that maximizes the PV/T exergy. In the future, studies including these points will be promoted. 7 refs., 7 figs., 3 tabs.

  12. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  13. Study of test procedure to evaluate airbag deployment force; Airbag tenkairyoku no hyoka shuho no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kamiji, K.; Fukuda, K.; Morita, K. [Honda Motor Co. Ltd., Tokyo (Japan)

    1998-05-01

    Discussions were given on airbags equipped in passenger cars as to methods of evaluating their deployment injuries. Airbag deployment injuries occur in occupants being out of position. In a driver`s seat, an injury may occur when an air bag deploys under a condition that a driver with relatively short body height gets closer to a steering wheel to maintain the driving posture. In a front passenger seat, if a child is not held in a restraint equipment, the child may be blown off into the vicinity of the airbag, whose deployment can cause an injury. According to the result of a test performed on a driver being out of position, the test method using a hybrid 3 dummy specified in the present ISO procedure may not necessarily be said to produce an evaluation on the worst case. In order to solve the problem, an ATD dummy which can measure bend in each rib independently would be used, or the hybrid 3 dummy must be measured in the worst set position. 4 refs., 8 figs.

  14. Environmental impact assessment caused by global warming. Chikyu ondanka no eikyoryo hyoka to sono taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, K [Geological Survey of Japan, Tokyo (Japan)

    1991-09-01

    This paper describes the considerations on the influence of the global warming on the environment, and the discussions on the measures against the climatic changes. With respect to the environmental effects by the global warming, the considerations were given based on the studies on the effects of mainly the Quaternary climatic changes on the surface sea water temperatures, sea level and animal flocks. If the magnitude of the climatic changes anticipated to occur during the 21st century is lower than that have taken place in the past 10,000 years during which the agricultural production has developed to a full-scale, there would be no fear of drastically changing the ecology on earth. If the estimation of future climatic and environmental changes becomes possible, then four basic positions could be selected for establishing the contermeasure plans. That is, the first is the measures to correspond to birth-rebirth transmigration; the second is the measures to carbon dioxide disposition upon concluding that the cause for the global warming is the atmospheric increase of carbon dioxide concentration, measures for conservation and international cooperation; the third is to deal with the warming environments; and the fourth is the means to reconstruct the earth. While a number of countermeasures may be prepared, Which of them should be selected will be decided by the amount of effects. 15 refs., 6 figs., 1 tab.

  15. Practical applications of superconducting technology; Chodendo gijutsu to sono oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, M.; Yamamoto, K.; Urata, M. [Toshiba Corp., Tokyo (Japan)

    1995-11-01

    Remarkable progress has been made in superconducting technology recently. This paper describes the details and technical features of every cooling type of practical superconducting magnet (SCM), including the SCM for magnetic resonance imaging (MRI), SCM for semiconductor pulling devices, high-field SCM, SCM for magnetically confined plasma devices, and SCM for particle detectors. Commercial production of pool-boil-cooled SCMs has been realized by reducing helium evaporation and decreasing the frequency of helium pouring. The development of forced-cooled SCMs has made it possible to build large SCMs. Moreover, the development of the 4 K-GM refrigerator has enabled liquid-helium-free SCMs to be introduced. Since this type of SCM can be operated merely by turning on a switch, SCMs are expected to come into more widespread use. 7 refs., 1 fig.

  16. Automobiles and safety; Jidosha gijutsu. Jidosha to anzen

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, K.; Goto, T.; Shimizu, T.; Yamanaka, A. [Toyota Motor Co. Ltd., Aichi (Japan)

    1998-08-01

    The number of road traffic victims in Japan has been above the level of 10,000 annually during 8 consecutive years, but in 1996 and 1997, it becomes below this level. The casualty of road traffic accidents is found to be occurred during driving and senior persons account for a large part among victims while 55.1% of the case took place at night. As for the countermeasures, it is possible to indicate the regulatory strengthening, advancement of accident investigation and analysis, provision of safety information to the user and research and development of advanced safety vehicle (ASV). Concerning preventive safety, studies on the human recognition, systems for assisting judgement and running and so on can be enumerated. The ASV is in the course of 2nd program that lasts until 2001 with 6 safety research subjects such as prevention, collision, automatic operation, containment of disaster from expanding and so forth. In terms of post-accident safety, remarkable research and development have been conducted on collision by means of dummy and human body, human resistance against injury, air bag for rider protection and child seat, and especially the form comparison of interior materials for head protection apparatus as well as study via simulation, together with commercialization of side bag for reducing head damages. As for car body materials, energy absorption by pillar type elements, use of aluminum materials, resistance comparison and design concept of structural separation and so on are being carried out. 69 refs., 1 fig.

  17. High-level water purifying technology. Kodo josui shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsugura, H; Tsukiashi, K [Meidensha Corp., Tokyo (Japan)

    1993-07-01

    Research and development have been carried out on a high-level water purifying system using ozone and activated charcoals to supply drinking water free of carcinogenic matters and odors. This system comprises a system to utilize ozone by using silent discharge and oxygen enriching device, and a living organism/activated charcoal treatment system. The latter system utilizes living organisms deposited on activated charcoal surfaces to remove polluting substances including ammonia. The treatment experimenting equipment comprises an ozone generating system, an ozone treating column, an activated charcoal treating column, an ozone/activated charcoal control device, and a water amount and quality measuring system. An experiment was carried out using an experimental plant with a capacity of 20 m[sup 3]/day on water taken from the sedimentation process at an actual water purifying plant. As a result, trihalomethane formation potential was removed at about 40% in the ozone treatment, and at 70% in the whole treatment combining the ozone and living organism/activated charcoal treatments. For parameterization of palatability of water, a method is being studied that utilizes nuclear magnetic resonance to investigate degrees of water cluster. The method is regarded promising. 1 ref., 4 figs.

  18. Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

  19. Automotive technology. ; Chassis. Jidosha gijutsu. ; Chassister dot sharyo seigyo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Ota, K.; Mor, H.; Ishizeki, S. (Fuji Heavy Industries Ltd., Tokyo (Japan))

    1990-07-01

    According to the trend of car suspensions announced in 1989, not only sports cars but also sedans have extensively applied a multi-link type and a double-wishbone type which are to improve operation stability and comfortableness by reexamining all their fundamental structures. Active suspensions with electronic control have been put to practical use and adopted for the first time to mass-produced cars such as INFINITI'' and CELICA''. Concerning steerings, most types of light cars are now equipped with power steerings. Moreover, application of air bags has increased, and safety has been improved by commercialization of the first mechanical air bags in addition to the conventional electrical ones. As for brakes, more anti-lock brakes have been used for 4WD cars and low-displacement cars. Motorcars with a traction control system have consequently increased. Thus both the anti-lock brakes and the traction control system are contributing to the improvement in safety. 17 figs., 2 tabs.

  20. Microbial EOR technology; Biseibutsu EOR gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Taguchi, M.; Yonebayashi, E. [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan)

    1995-11-10

    This paper describes attempts of establishing an oil recovery technology utilizing microorganisms and of aiming at improving the practicability of that technology. Fiscal 1994 has investigated effects of inorganic salts existing in reservoir beds and NaCl concentrations on proliferation of microorganisms and production of metabolites. The investigation was intended to discuss applicability of microorganisms to environments that are brought closer to actual field conditions. Furthermore, a core sweeping test using sandstone was carried out on the fiscal 1992 separated bacteria, the 4118 bacteria, that has high surfactant production capability. In addition, a sand pack was used to perform a flooding experiment under conditions of 50{degree}C and 50 KSC to evaluate functionality of microorganisms when environments in the reservoir bed are simulated with respect to pressures and temperatures. An oil recovering experiment was carried out using a sandstone with a diameter of 1.5 inches, a length of 1.0 foot and permeability of 600 md, and using Bacillus subtilis 4118 bacteria which attained the lowest interfacial tension among the bacteria examined. A recovery rate of 4.4% Sor was derived in the experiment. A recovery rate of 29.0% Sor at maximum was obtained when Bacillus licheniformis 18-2-a bacteria was supplied into a sand pack filled with silica sand. 20 figs., 7 tabs.

  1. Photon technology. Laser process technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing laser process technology by interaction between substance and photon, the present state, system, R and D issues and proposal of such technology were summarized. Development of the photon technology aims at the modification of bonding conditions of substances by quantum energy of photon, and the new process technology for generating ultra- high temperature and pressure fields by concentrating photon on a minute region. Photon technology contributes to not only the conventional mechanical and thermal forming and removal machining but also function added machining (photon machining) in quantum level and new machining technology ranging from macro- to micro-machining, creating a new industrial field. This technology extends various fields from the basis of physics and chemistry to new bonding technology. Development of a compact high-quality high-power high-efficiency photon source, and advanced photon transmission technology are necessary. The basic explication of an unsolved physicochemical phenomenon related to photon and substance, and development of related application technologies are essential. 328 refs., 147 figs., 13 tabs.

  2. Technique of CWM distribution system; CWM ryutsu chukei system gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Konno, K [Center for Coal Utilization, Japan, Tokyo (Japan); Tanaka, M

    1996-09-01

    It may be intended that CWM is manufactured in areas near coal producing areas in overseas countries and imported as a product requiring lower handling cost than in bulk products. In order to achieve this idea, it is necessary to establish a distribution and relaying system for product transportation inside and outside the country, including relaying bases for receiving, loading and storing the product. This paper reports results of the demonstration tests performed since 1992 to 1996. In the tests, CWM made from Chinese coals was transported from Shijiu Port to the Hibiki relaying base in the city of Kita-Kyushu on 5000 DWT ocean vessels, unloaded, stored, and loaded again on 700 DWT domestic vessels for distribution to users. Since the inauguration of transportations, 40,000 tons of CWM were delivered yearly to the Okayama plant of Tayca Company, and about 20,000 tons to the Mizushima power plant of the Chubu Electric Power Company over a period from 1995 to 1996. During the period, a number of findings were acquired in different aspects, including quality control of incoming and outgoing CWM, stability in quantity and properties, loading and unloading works, and transportation. Although reduction in subsidence during transportation and storage was indicated desirable, the practical applicability was verified for the relaying system as a whole. 4 refs., 15 figs., 3 tabs.

  3. Technology for improving sludge concentration; Odei noshukusei kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-10

    Sludge generating in a sewage treatment plant is disposed through the processes such as concentration, dehydration, and incineration in sludge disposal facilities. In recent years, there has been a trend that this sludge increases in volume as well as worsens in the concentration. A case is predictable where the sludge load to the dehydrating process is so large that the sludge can no longer be processed in sufficient quantity. In the meantime, if sludge is ozone-treated, viscous substance on the surface of sludge particles can be separated with a comparatively small amount of ozone, with sludge concentration enhanced. At Meidensha, an experimental plant was set up for the ozone treatment of sludge in a sludge intensive treatment plant of a metropolis, with a verification experiment carried out for a sludge concentration improving system by ozone. As a result of comparison of the treatment performance between an assessment system for performing ozone treatment and a reference system for not performing, the average value of the sludge concentration of a gravity concentration tank was 1.9% of the reference system against 1.7% of the assessment system in a continuous treatment experiment in the summer, while the solid collection ratio was 65.8% of the reference system against 95.5% of the assessment system, enabling a superior improving effect to be obtained. (NEDO)

  4. Winter concrete; Kanchu kunkurito. Gijutsu no genjo to shorai tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Kamata, Eiji [Hokkaido University, Hokkaido (Japan)

    1998-11-10

    Much energy is consumed in order to carry out the winter concrete, and it becomes not always the work in the work environment of the amenity. Therefore, it wants to avoid it, if such work is possible. The winter concrete is a basis in carrying out the construction in cold region in all year. Large role is very much fulfilled for efficient operation of the construction industry in which foot of maintain is wide, activation of the regional economy of snows cold region such as the constant employment of construction worker, improvement in the social environment. Therefore, the popularization of the winter concrete technology is indispensable in the chilly snowy area, and it becomes the importance that the efficiency improvement is attempted. (NEDO)

  5. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research results of hard photon technology have been summarized as a part of novel technology development highly utilizing the quantum nature of photon. Hard photon technology refers to photon beam technologies which use photon in the 0.1 to 200 nm wavelength region. Hard photon has not been used in industry due to the lack of suitable photon sources and optical devices. However, hard photon in this wavelength region is expected to bring about innovations in such areas as ultrafine processing and material synthesis due to its atom selective reaction, inner shell excitation reaction, and spatially high resolution. Then, technological themes and possibility have been surveyed. Although there are principle proposes and their verification of individual technologies for the technologies of hard photon generation, regulation and utilization, they are still far from the practical applications. For the photon source technology, the laser diode pumped driver laser technology, laser plasma photon source technology, synchrotron radiation photon source technology, and vacuum ultraviolet photon source technology are presented. For the optical device technology, the multi-layer film technology for beam mirrors and the non-spherical lens processing technology are introduced. Also are described the reduction lithography technology, hard photon excitation process, and methods of analysis and measurement. 430 refs., 165 figs., 23 tabs.

  6. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the application of photon to industrial technologies, in particular, a hard photon technology was surveyed which uses photon beams of 0.1-200nm in wavelength. Its features such as selective atom reaction, dense inner shell excitation and spacial high resolution by quantum energy are expected to provide innovative techniques for various field such as fine machining, material synthesis and advanced inspection technology. This wavelength region has been hardly utilized for industrial fields because of poor development of suitable photon sources and optical devices. The developmental meaning, usable time and issue of a hard photon reduction lithography were surveyed as lithography in ultra-fine region below 0.1{mu}m. On hard photon analysis/evaluation technology, the industrial use of analysis, measurement and evaluation technologies by micro-beam was viewed, and optimum photon sources and optical systems were surveyed. Prediction of surface and surface layer modification by inner shell excitation, the future trend of this process and development of a vacuum ultraviolet light source were also surveyed. 383 refs., 153 figs., 17 tabs.

  7. Paradigm for new scientific technology; Shinkagaku gijutsu paradigm

    Energy Technology Data Exchange (ETDEWEB)

    Shindo, Y [National Chemical Lab. for Industry, Tokyo (Japan)

    1995-01-05

    This paper reviews the current status from the standpoint of chemical engineers facing the coming of the 21st century, and surveys the paradigm for new scientific technologies. The criticism is mixed with unique opinions everywhere, such as `departure of students from scientific and engineering faculties is none other than the result of a market principle`, `national burden of trillions of yens should not be spent only under a justice of advancement of the science`, and `the global civilization itself has no other way but to change from the conventional expansive development type of the western country style to the internal development type of the oriental country style`. Values that define the paradigm for new scientific technologies may include such keywords as saturation in technology, baseless expansion of research projects, criticism on science, market principle, and centering human being. It should be looked at seriously that profit from research and development should exceed the cast invested therein in the future, and scientific technologies that serve truly the society should be aimed at. These efforts will result in one of the large pillars that support the future in which creation of new functions is aimed at as a result of structuring the new systems. Trying to overcome the environmental problems is one of them.

  8. Laser innovated manufacturing technology; Laser ga seisan gijutsu wo kakushinshita

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, I. [Honda Motor Co. Ltd., Tokyo (Japan)

    1996-11-01

    This paper looks back the history of applications of laser processing in the automobile industry, and introduces contents of some particularly unique applications from among them. The CO2 laser and YAG laser that are used mainly have increased their outputs with the times, and 50-kW CO2 laser and 4-kW YAG laser have now become available commercially. The laser processing has become used widely for cutting purpose in Japan, which is in contrast with their high application to welding in Europe and America. Cutting thick plates has been developed recently, which is applicable to plates as thick as about 25 mm. A flexible system in which YAG laser is combined with an optical fiber/articulated robot is operating for three-dimensional shape processing. Automobile makers are adopting laser processing for welding in place of the electron beam welding that has been used conventionally. The process is used also for a number of other applications including surface reformation, such as surface quenching for cylinder liner, and valve seat padding. 8 refs., 8 figs.

  9. Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-09-01

    Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

  10. Quantitative relationship between SAR and temperature rise inside eyeball in a realistic human heat model for 1.5 GHz-microwave exposure; 1.5GHz maikuroha wo abita tobu real model ni okeru gankyunai no hikyushuritsu to josho ondo tono teiryo kankei

    Energy Technology Data Exchange (ETDEWEB)

    Takai, K.; Fujiwara, O. [Nagoya Institute of Technology, Nagoya (Japan)

    1997-12-20

    For investigating biological effects of a localized SAR (specific absorption rate) deposited in a human body for electromagnetic wave exposure, it is indispensable to graps a temperature-rise inside a human brain including the control center for the body temperature. This paper numerically analyzes a temperature-rise inside an eyeball of our developed realistic head model for 1.5 GHz microwave exposure, using the FD-TD (finite-difference time-domain) method. The computed results are validated in comparison with the data obtained by Taflove and his colleague. In order to examine a quantitative relationship between the localized SAR and temperature-rise, we also obtained a tissue amount over which the localized SAR should be averaged so as to well reflect the temperature-rise distribution inside the eyeball. 15 refs., 9 figs., 3 tabs.

  11. Local approach to brittle fracture under residual stress field. Assessment of pre-loading effect; Local approach no tekiyo ni yoru zanryu oryoku wo motsu buzai no zeisei hakai kyodo hyoka. Yokaju no eikyo no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Y.; Sakano, K.; Onozuka, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Minami, F. [Osaka University, Osaka (Japan)

    2000-01-01

    The effect of residual stresses on brittle fracture was investigated on the basis of the Local Approach. Compressive residual stress was introduced by pre-loading and the subsequent fracture test conducted with a 780 MPa class steel. Preloading apparently increased the critical load and critical CTOD at the onset of brittle fracture initiation. The Weibull stress criterion was used to evaluate the brittle fracture resistance of the pre-loaded specimen. The critical Weibull stress is a material property independent of test conditions with and without pre-loading. Using the Weibull stress criterion, the critical CTOD of the pre-loaded specimen can be predicted from test results of the specimen without pre-loading. (author)

  12. NEDO Forum 2000. Proliferation of information and achievements, and evaluation session (toward achievement evaluation and information signaling); Joho seika no fukyu to hyoka session. Seika no hyoka to joho hasshin ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The following themes were presented at the present session: (1) fundamental survey on evaluation of projects, (2) the IEA information exchange agreement project and information providing activities by NEDO, (3) the NEDO technological information database, (4) the NEDO's intelligent property releasing institution and utilization of the patent database, (5) examples of successful utilization of NEDO patents (mask producing equipment by means of electronic beam depiction), and (6) special lectures (the current status of information network technologies and their new development in the future). Item (1) describes a method to evaluate reasonability of decision makings at each time point around project management, in which time divisions are set, and compared with requirements in each time. It also describes discussions on the reasonability thereof. As the execution agreement with IEA for energy technology data exchange (ETDE), Item (2) introduces the IEA energy and environment technology information (a project by Centre for the Analysis and Dissemination of Demonstrated Energy Technology (CADDET) and a project of Greenhouse Gas Technology Information Exchange (GREENTIE)), as well as the execution agreement to establish IEA coal researches, and the NEDO information providing activities. Item (3) introduces the NEDO project information, NEDO achievement report, CADDET database, and GREENTIE database as the databases provided by the NEDO Information Center. (NEDO)

  13. Interim report on research and development of super heat pump energy accumulation system by the evaluation working group; Super heat pump energy shuseki system hyoka work group chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The evaluation working group of the Large-scale Energy-saving Technology Research and Development Promotion Council has made an interim evaluation of the results obtained so far by the R and D project for the super heat pump energy accumulation systems. The working group evaluates the bench plant operation test results comprehensively, covering technical, economic and social aspects, and R and D promotion methodology. The working group has concluded that a significant technological break-through is made for the super high performance compression heat pumps, and the technological groundwork is now established for the future pilot system. For the chemical heat storage technologies, it is concluded that system feasibility is demonstrated, and the technological groundwork for the future development is established. The super heat pump is evaluated to potentially realize significant economic superiority over the conventional devices both in the domestic and industrial areas, and to be highly rated potentially in the areas of energy-saving, power load leveling and environmental preservation. (NEDO)

  14. Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-10-01

    Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

  15. Report on the environmental safety evaluation sub-committee in fiscal 1992; 1992 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the environmental safety evaluation sub-committee for the coal liquefaction plant in fiscal 1992. The sub-committee, upon having received reports on the result of environmental safety evaluation tests performed in fiscals 1991 and 1992 by NEDO, deliberated and discussed carefully the contents thereof. In order to ensure labor hygiene for coal liquefaction plant workers, health influence on liquefied oil users, and social acceptability of the liquefied oil, NEDO has performed the comprehensive brown coal pilot plant operation and oil safety tests. The tests are in accordance with the labor safety and hygiene law, the chemicals examination law, and the MPD issued by OECD, and performed on each fraction produced in the pilot plant and the whole fraction mixing the former fractions, using rats, rabbits, and guinea pigs. The test items included: acute inhalation toxicity and oral repeated administration (using rats); eye stimulation, repeated coating and skin stimulation (using rabbits); photo-toxicity (using guinea pigs); mutagenicity tests (microorganisms, bacteria and chromosome anomaly); resolution tests; fish toxicity; concentration degrees; algae growth obstruction; and water flea breeding obstruction. As the result, the toxicity was found light. (NEDO)

  16. Evaluation of permeability of Nojima fault by hydrophone VSP; Hydrophone VSP ni yoru Nojima danso no tosuisei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)

    1996-05-01

    The multi-offset hydrophone VSP experiments were carried out using a 750m deep borehole as the oscillation receiver, which penetrates the Nojima fault, to detect water-permeable cracks and evaluate their characteristics. Soil around the borehole is of granodiorite, and fault clay is found at a depth in a range from 623 to 624m. A total of 4 dynamite tunnels were provided around the borehole as the focus. The VSP results show that the tube waves are generated at 22 depths, including the depth at which fault clay is found. However, these waves are generated at only 6 depths in an approximately 150m long fracture zone, suggesting that the cracks in the zone are not necessarily permeable. It is also found that crack angle determined by the analysis of tube waves almost coincides with that of fault clay determined by the core, BHTV and FMI, and that permeability is of the order of 100md at a depth of fault clay or shallower. 3 refs., 2 figs., 2 tabs.

  17. Evaluation of economical efficiency of the Osaki large hydroponic facilities; Osaki ogata suiko shisetsu no keizaisei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yonezawa, K [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1996-03-25

    A demonstrative test was conducted to verify economical efficiency of practical scale hydroponic horticulture under structure making use of a part of the Osaki thermal power plant to be constructed. In the test, the hydroponic culture of leek and tomatoes was carried out for six years starting 1989 to study its economical efficiency. Using the M-type hydroponic culture facilities, the structures are 1200m wide, 29m long, and 21 tons in the culture liquid level in case of leek, and 350m wide, 29m long, and 10 tons in the culture liquid level in case of tomatoes. The evaluation was made estimating the crop amount of leek as about 35 tons and that of tomatoes as about 60 tons and regarding that the sales amount is equal to the crop amount. The sales amount of leek is 28 million yen, and when seeking income/expenditure from expenses, deficit of 1 million yen per 30 a cannot be avoided excluding the equipment depreciation cost. As to tomatoes, the shipment cost is approximately 14 million yen without the equipment depreciation cost, but the sales amount is approximately 13-19 million yen largely affected by the unit price. A study on the sale method is needed. 7 figs., 11 tabs.

  18. Investigating the effect of aeration powder filling on the actual compacting press; Eareto jutenho no jikki press deno hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, M. [Toyota Central Research and Development Labs., Inc., Nagoya (Japan); Urata, I. [Toyota Motor Co. Ltd., Aichi (Japan)

    1998-05-15

    The authors proposed an aeration filling method as a new filling method in order to obtain uniform and high speed filling by carrying out basic experiments on powder material filling using a visual apparatus. In this study, the aeration powder filling was applied to the product compacting on the actual compacting press, and its evaluation was carried out. As a result, the following effects were confirmed. The weight scattering was reduced to about 70% in the high speed filling and about 50% in the low speed filling. The maximum density was reduced to about 30% in the high speed filling and about 25% in the low speed filling. The maximum thickness difference was reduced to 65% in the high speed filling and about 20% in the low speed filling. The aeration powder effect was stronger in the high speed filling than that in the low speed filling. The weight and size accuracy of the components were increased by the aeration powder filling. The pause and the shaking operation were discarded in the front part of the powder box, thus the filling time could be remarkable shortened. 3 refs., 6 figs.

  19. Treatability evaluation of membrane technique by virus. Maku shori ni okeru shorisei hyoka to shite no virus

    Energy Technology Data Exchange (ETDEWEB)

    Yano, K. (Tokyo Metropolitan Research Lab. of Public Health, Tokyo (Japan))

    1990-08-10

    Concerning a high level treating method of regeneration of sewage water, there are methods of coagulation/precipitation, sand filtering and ozone treatment in addition to the conventional active sludge method. However, none of these methods are perfect from the viewpoint of virus. A film treating method to remove micro-organisms in water is twofold, i.e., microfiltration and reverse osmosis. For such filter treatments, polio virus is most suited as an experimental index for conducting an assessment of the treating ability of viruses. The reasons are as follows: 1. It is the smallest virus among the viruses which are mixed in the water systems. 2. Polio virus is always detected in the study of actual conditions of the viruses contained in the sewage waters. 3. It involves less danger in handling because there are vaccines which are made less poisonous. 4. Separation and quantification of viruses is easily conducted by means of cultured cells. 8 refs., 1 fig., 7 tabs.

  20. Evaluation of paramagnetic species in coals with iodine doping technique; Yoso tenkaho wo mochiita sekitanchu no jojiseishu no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, S.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability for the iodine increases. In a system with the entire spin being uniform, the spectrum height shows a saturation phenomenon against increase in microwave output. A non-uniform system, in which the oriented spin forms small groups and is in local thermal equilibrium, does not show saturation, but increases monotonously. 2 refs., 5 figs.

  1. Report on the environmental safety evaluation sub-committee meetings in fiscal 1987; 1987 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The environmental safety evaluation sub-committee has held two meeting in the current fiscal year as described below. The first sub-committee meeting (August 25, 1987) was held for the agenda of the summary of future test plans, the result of overseas surveys in fiscal 1986, the results of tests in fiscal 1986, and the summary of the test plan for fiscal 1987. The major agendum of the second sub-committee meeting (February 23) was the interim reports on the overseas survey results and the safety tests in fiscal 1987. NEDO intends to ensure the labor hygiene for workers in coal liquefying plants, the effect of liquefied oil on users' health, and social acceptability of liquefied oil. Therefore, a safety test for liquefied oil in the primary hydrogenation process was performed provisionally on brown coal PP in the initial stage of operation, in addition to bituminous coal liquefied oil at the existing 1-t/d PDU. The main contents of the test performed by NEDO are based on the labor safety and hygiene law and the law related to regulation on the deliberation and manufacture of chemical materials. Different tests using guinea pigs were carried out on the total fraction mixed at the 1-t/d PDU, and each fraction of light and heavy oils, where the liquefied oil was verified to have minor degree of toxicity. (NEDO)

  2. What will be brought about by changes in evaluation standards; Kachi hyoka kijun no henka ga motarasu mono

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawaa, J. [Hokkaido University, Sapporo (Japan)

    1999-12-17

    The author expresses his opinion toward the impact to be brought about by changes in evaluation standards mainly involving the power system. The 20th century has been an age of mass production of various articles and mass consumption of various resources. It has become evident of late that flexibility, which will realize environmental impact reduction and satisfy varying needs, should be added to the evaluation standards. The new evaluation standards urge that the large-scale centralized management type system be converted into an autonomous distributed type system, and mass production into small-scale production of multiple articles. The development from centralization to decentralization, and the trend toward deregulation and the corporation's plan of dividing itself into plural in-house companies, may be evaluated against the same context. In the field of power systems, it is deemed that the diffusion of power retailing business and distributed power sources will be accelerated. When it comes to a power system constitution and operation capable of dealing with the new development, an autonomous distributed type system constitution and operation as a local energy system is supposed to be more appropriate than the conventional centralized management type. (NEDO)

  3. Research on elaboration of the evaluation guidelines for activities implemented jointly; Kyodo jisshi katsudo hyoka guide line sakutei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Elaboration of the evaluation guidelines for activities implemented jointly (AIJ) was researched to prevent the earth from warming. AIJ is the means to globally promote countermeasures against global warming cost-effectively by optimally combining every country`s technology, know-how and fund. AIJ was established in the 1st Conference of the Parties (COPI) of the United Nations Framework Convention on Climate Change in March, 1995. The pilot phase of AIJ is first carried out by voluntary workers jointly with developing countries under the agreement of the parties. The current situation of activities is reported in COPI as materials for evaluation of AIJ. To promote AIJ, elaboration of the evaluation guidelines for AIJ Japan program is also necessary for Japan. This research arranged the contents of the evaluation guidelines and the method of classifying projects for AIJ Japan program, and carried out some case studies of promising projects to reduce greenhouse gas emission for future proposal. 3 figs., 31 tabs.

  4. Application of cytotoxicity test for toxic micropollutants. Saibo dokusei shiken ni yoru yugai kagaku busshitsu osen no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Utsumi, H; Hamada, A [Showa University, Tokyo (Japan). School of Pharmaceutical Science; Ono, Y [National Institute of Hygienic Sciences, Tokyo (Japan)

    1992-10-01

    Considerations were given from a viewpoint of assessing toxicity to human bodies on methods of assessing water pollutants and organisms, and applicability of cytotoxity test using cultured cells to water quality assessment. Biological assessment systems used for water environment may use tests using multicellular organisms, cells, or organelles in cells. The organism assessment method is intended mainly for assessing ecological effects, and a suitable method must be selected upon extrapolating it to human bodies. A toxicity parameter used most frequently in a cytotoxity test is the cell revival rate, and life and death are determined from liberation of enzymes in cells, or with color rejection tests and incorporation tests. There are a number of test specimens of raw tap water and its chlorine treatment condensate that show no mutagenicity but cytotoxity. Efficiencies of removal by means of mild chlorine treatment, fast filtration, and activated carbon adsorption vary greatly with cytotoxity and mutagenicity. Introducing the cytotoxity test is expected of further contributing to improving safety in water quality. 24 refs., 1 fig., 7 tabs.

  5. Microbiological indicators for evaluating treatability on water purification process. Josui shori ni okeru shorisei hyoka kara mita biseibutsu shihyo

    Energy Technology Data Exchange (ETDEWEB)

    Ichikawa, H [Kanagawa Prefectural Government Public Enterprise Egency Water Works Bureau, Kanagawa (Japan). Tanigahara Purification Plant

    1990-08-10

    This report describes the historical procedure of a bacterial test for a certain respective bacteria, and also describes the removal of micro-organisms by a water treatment and treatment with disinfectants. The disinfection is made mainly on basis of foreign literature. This is because there exist few literature published in Japan. In a good sense, this is because of the Japanese habit of drinking raw water which has contributed to high level of facilities and the maintenance. If seen from a different viewpoint, the prsent concern is concentrated to a contamination of the underground water by organic solvent and the counter measure against such minute quantity of organic chemicals as trihalomethane and the agricultural chemicals in the golf courses. From the consumers {prime} standpoint, these are of the level of problems that only one affected person increases per year for 100,000 inhabitants even if they continue to drink such drinking waters continuously through their life years. The reality is that it is remote from the realities in life. 37 refs., 9 tabs.

  6. Accuracy of parameters of permeable fractures by hydrophone VSP; Hydrophone VSP ni yoru tosuisei kiretsu no tokusei hyoka no seido

    Energy Technology Data Exchange (ETDEWEB)

    Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Yabuuchi, S; Hasegawa, K [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

    1997-10-22

    Hydrophone VSP (vertical seismic profiling) experiment is under way as a technique for detecting subsurface water-permeable cracks by use of boreholes and for evaluating their characteristics (permeability index, crack direction, dip angle). In this report, tube waves observed by hydrophone VSP are subjected to analysis for the determination of water-permeable crack characteristics, the impact caused by errors in the value inputted for analysis is estimated, and a model calculation is performed in case there is no agreement between data from the borehole and data from VSP, all for examining the VSP records for accuracy. When an error rate of 15% is given to the tube wave/P-wave amplitude ratio, a change of 40% or lower results in the permeability index, and a change of 10deg or less in the dip angle, which means that an error in the amplitude ratio does not affect the analysis very much. Changes in the amplitude ratio resulting from changes in crack direction and dip angle differ, dependent on the offset rate. When angular differences among plural crack directions are within 90deg and dip angles within 60deg, the result of analysis represents the average characteristics of the plural cracks. 7 refs., 5 figs., 2 tabs.

  7. How to examine flaking sex evaluation of the float bus bottom brick; Furotobasubotomu renga no furekingu sei hyoka shiken hoho

    Energy Technology Data Exchange (ETDEWEB)

    Yoneyama, R. [Yotai Refractories Corp., Osaka (Japan)

    1999-02-01

    After it was used in the float law glass dissolution drawer fireplace bottom, a countermeasure was established by answer, laboratory simulation and high temperature load deformation investigation that that cause was in performance about incumbent elephant of the bottom department clay brick which becomes clear from the second. Though it accompanies melting metal tin and Na that it got into the inside of the brick is a cause as for formation, is expected future development by the high research of the practical use which effective measure was taken against by the organization of the clay brick and the improvement of the physical nature. (translated by NEDO)

  8. Interim evaluation report on research and development of automatic sewing systems; Jido hosei system no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development project for automatic sewing systems is aimed at establishing the techniques necessary for developing (automatic sewing systems) which efficiently produce diversified types of products in small quantities, to cope with various requirements, e.g., diversified consumers' needs and reduced cycle periods. This project covers R and D of the sewing preparation/processing, sewing/assembling, cloth handling, and system management/control techniques. The program for developing the total systems and elementary techniques draws the conceptual designs of their functions, performance and shapes, to outline the overall R and D project. The programs for the individual elementary techniques include studies on their basic functions and performance; design works from the basic designs to determine the specifications to the detailed designs of the devices to be developed; construction of the test units on a trial basis; and function confirming tests to confirm operability of the unit components and device performance, where these works are simultaneously implemented. This paper describes the interim results of evaluation of the elements developed for the elementary techniques, summarizing the results obtained so far. It is concluded that most of the targets of the R and D themes are sufficiently achieved by the end of FY 1987, and that the project can be now advanced to the next phase, construction of the test plants. (NEDO)

  9. Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K; Suzuki, H; Hosomi, I [The University of Tokyo, Tokyo (Japan); Nahata, H [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

    1997-12-31

    The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

  10. Evaluation of column flotation results with a film flotation method; Film fusenho wo mochiita column fusen kekkan no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Matsukata, M.; Ueyama, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1996-10-28

    Change in wettability of coal particle surfaces due to kerosene adsorption was studied by using a film flotation method. The applicability of a film flotation method to coals modified by kerosene adsorption was first confirmed. In experiment, film flotation was applied to Illinois coal modified by aqueous methanol solution and kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface and kerosene in aqueous methanol solution were analyzed to verify the applicability of a film flotation method. Film flotation was applied to Datong and Illinois coals modified by kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface was plotted to surface tension of liquid. As a result, the weight percent of hydrophobic particles within 50mN/m in surface tension slightly increased in Datong coal and remarkably increased in Illinois coal with kerosene addition. It was thus suggested that in addition to surface tension, the distributions of hydrophilic and hydrophobic strengths on the surface of each coal particle should be considered to understand attachment of coal particles and bubbles. 6 refs., 4 figs.

  11. Performance evaluation of a flow-down collecting solar system; Ryuka shunetsushiki solar system no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kanayama, K; Li, X; Baba, H; Endo, N [Kitami Institute of Technology, (Japan)

    1997-11-25

    The paper evaluated performance of a flow-down collecting solar system. The solar heat pump PV system is composed of a solar system, heat pump and PV, of which the heat collecting portion is a water-use horizontal evacuated double glass tube solar collector. As a result of the performance measurement, the necessity of fundamental improvement arose. Under an idea of disproving common sense of the original forced circulation solar system, a system was designed in which heat is collected by making the heat media reversely circulate and flow down in accordance with gravity. When the flow rate was 2m{sup 3}/h, the collecting rate reached a maximum, approximately 54% (36.9% before improvement). When the flow rate was 1.3-1.5m{sup 3}/h, the system can realize the maximum merit, and the collecting efficiency became approximately 50%. Helped by reduction in consumed power, the average system performance coefficient reached more than 85% (28.9% before improvement). The obtainable energy rate rapidly increased to 2.9 times more than before improvement. Further, the consumed power of pump was decreased 65% from before improvement when the flow rate was 2.4m{sup 3}/h. 2 refs., 5 figs.

  12. Geological evaluation on productibility of coal seam gas; Coal seam gas no chishitsugakuteki shigen hyoka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, K [University of Shizuoka, Shizuoka (Japan). Faculty of Education

    1996-09-01

    Coal seam gas is also called coal bed methane gas, indicating the gas existing in coal beds. The gas is distinguished from the oil field based gas, and also called non-conventional type gas. Its confirmed reserve is estimated to be 24 trillion m {sup 3}, with the trend of its development seen worldwide as utilization of unused resource. For the necessity of cultivating relevant technologies in Japan, this paper considers processes of production, movement, stockpiling, and accumulation of the gas. Its productibility is controlled by thickness of a coal bed, degree of coalification, gas content, permeability, groundwater flow, and deposition structure. Gas generation potential is evaluated by existing conditions of coal and degree of coalification, and methane production by biological origin and thermal origin. Economically viable methane gas is mainly of the latter origin. Evaluating gas reserve potential requires identification of the whole mechanism of adsorption, accumulation and movement of methane gas. The gas is expected of effect on environmental aspects in addition to availability as utilization of unused energy. 5 figs.

  13. Fracture mapping in rock slope using geophysical instruments; Butsuri tansa ni yoru ganban shamennai no kiretsu bunpu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kurahashi, T; Inazaki, T [Public Works Research Institute, Tsukuba (Japan); Watanabe, S [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    An attempt was made to visualize distribution of cracks in a rock slope by applying geophysical survey onto a rock slope. Geophysical logging and seismic survey using the reflection method were used as the methods for the geophysical survey. The rock slope subjected to the survey is located in a gorge along the Yoshino river in Yamashiro Town, Tokushima Prefecture. The slope has a width of 25 m and a height of 30 m. Its overhang in a nose form may has a possibility of causing collapse due to sliding. Cracks developed by horizontal schistosity were detected by performing geophysical logging on VSP, calipers, natural gamma-ray spectra, temperature and borehole in a borehole drilled vertically from the top of the slope. The seismic survey using the reflection method detected the cracks by emphasizing joints in the perpendicular direction. A possibility was shown to visualize the crack distribution with high resolution by using the above geophysical survey on the rock slope. In order to detect the crack distribution with still higher resolution, development into a three-dimensional exploration in the future is desired, not to speak of improvement in signal receivers, and discussions on geometry. 1 ref., 6 figs.

  14. On the method for fracture strength assessment. Part 2; Kozobutsu no hakai kyodo hyoka no jissai. 2

    Energy Technology Data Exchange (ETDEWEB)

    Onozuka, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1995-09-05

    In order to reduce the economic cost of the generating set etc. the damages to the materials and structures of the structure to last the original design life were observed and it was considered that if damages were fewer the life would be longer. One of the important items in assessing, amending and renewing the rationality of the established structure is the assessment of the defects and flaws existing in the welded joints. In Japan, WES 2805 which is named as the Method for Assessing the Defects for the Brittle Fracture Occurring Properties of Welded Joint was formulated in 1980 as the standard of the Japan Welding Society. Although it has been applied as the criterion in wide range, the part on brittle fracture is now under revision to reflect the research results on fracture mechanics thereafter and to perfect the fracture relationship because many years have passed since its first formulation. In this paper, the contents in the final stage of the revision of WES 2805 standard, including concrete examples, were introduced. 2 refs., 6 figs., 2 tabs.

  15. Feasibility study for seismic monitoring of gas injection; Atsunyu gasu monitaringu no kanosei hyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, A.; Ogawa, T.; Yokota, T.; Shimada, N.; Onozuka, S.; Kono, F.; Miyagi, T. [Japan National Oil Corp., Tokyo (Japan)

    1998-10-30

    In this study, seismic monitoring of injected gas in a carbonate reservoir was investigated using multidisciplinary approach which consisted of geological/reservoir modeling, reservoir flow simulation, rock physics and seismic modeling. A case study was conducted over Lower Cretaceous carbonate reservoir offshore Abu Dhabi. The gas saturation and reservoir pressure data were obtained from the reservoir flow simulation. The velocity data of dry rock samples under the various conditions were also obtained from rock physics study. These outputs were converted to the velocity model using Gassmann's equation. The calculated velocity from Gassmann's equation is well correlated with velocity from laboratory measurements. Therefore we con confirm that the Gassmann's equation is applicable to estimate the velocity of the gas saturated reservoir rock. Based on the velocity model, synthetic seismic sections before and after gas injection were constructed in order to verify the influence of gas flood. As the results, amplitude difference between the two synthetic seismograms was observed at top and bottom reflectors of the reservoir zone. This amplitude variation is caused by both gas saturation change and pressure change. Although further investigation is needed to detect the cause of the variation, this study indicates the possibility of seismic reservoir monitoring. (author)

  16. Evaluation on the effect of tsunami and seaquake on the floating structure; Tsunami kaishin no futai ni taisuru eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Suzuki, H.; Hosomi, I. [The University of Tokyo, Tokyo (Japan); Nahata, H. [The Long-Term Credit Bank of Japan, Ltd., Tokyo (Japan)

    1996-12-31

    The effects of tsunami and seaquake on large floating structures are theoretically studied, where these effects are followed in terms of local strength using the equation proposed by Sells to predict surface shapes changed by seaquake-caused uplift of the seabottom. The equation is combined with the one for tsunami propagation, to better predict the tsunami motion. The simulation results indicate the necessity of considering the effects of tsunami for the design of a large floating structure. The authors discuss that the effect of tsunami is minimized when a floating structure is set at a depth of at least 40 to 50m, chain length should be determined by equalizing the breaking weight with the load at which the structure starts to move, and a structure should be set at a position where it is not attacked by transverse waves. They also discuss that seaquake intensity should be predicted by the equation of motion of compressible fluid, and, noting local strength of a floating structure, it will not be damaged when it is at least 16mm thick under the conditions of 2m as seabottom uplift and 0.5m as draft depth. 15 refs., 9 figs., 2 tabs.

  17. Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

  18. Framework of information system assessment based on function and quality; Kino to hinshitsu ni motozuku joho system hyoka no wakugumi

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, M.; Hishitani, J. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    As for function and quality of information system, an assessment method of productivity at planning and at completion has been developed. In this method, functional size expressing the size of functional kinds provided by the system, value-added size expressing the size with corrected functional size in response to the quality level of each function, and production size expressing the size of products and processes under the given conditions were employed as indexes for evaluating the size of system. In addition, a method using the quality property tree has been developed. In this method, to evaluate the quality level which is essential for calculating the value-added size, users and providers evaluate the system quality from their own viewpoints. By this system, validity of user`s demand and validity/efficiency of realizing process can be evaluated for client/server type systems from the systematic viewpoint in a whole life cycle of systems from development planning to abandonment of systems. 24 refs., 5 figs., 3 tabs.

  19. Development and applicability estimation of the tire contact pressure measurement system; Tire secchiatsukei no kaihatsu to oyosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Mizutani, Y.; Amago, T.; Takahashi, T.; Sakuma, S.; Mori, N. [Toyota Central R and D Laboratories, Inc., Aichi (Japan); Nagae, A. [Toyota Motor Corp., Aichi (Japan); Yasuoka, M. [Toyo Tire and Rubber Co. Ltd., Osaka (Japan)

    1995-04-20

    A pressure sensor more reliable than the conventional types and a tire pressure measurement system using a plurality of sensors of the said reliable type have been developed. The sensor is an inverted T in shape, the upper surface of the vertical beam thereof receives the pressure, and the two ends of the horizontal beam are fixed. The load per unit area imposed on the pressure receiving surface is separated into three components, the X and Y components in the tangential direction are sensed by the vertical beam while the Z component in the vertical direction is sensed by a distortion gauge attached to the horizontal beam. For the measurement of the contact pressure distribution for the entire contact surface, a measuring device was developed, comprising a multiple point contact pressure gauge with 30 sensors of the reliable type discussed here embedded therein, a tire rolling tester, and a data processing unit. A tire wear estimation test was conducted using this pressure sensor and a contact probe type slip sensor, and it was found that a tire of a greater friction energy ratio is easier to experience abnormal abrasion and that the new pressure sensor is useful in estimating abnormal abrasion. Further, it was indicated that the present measuring device is applicable to the analysis of the mechanism wherein shaft force results from contact pressure on the soil. 3 refs., 11 figs., 3 tabs.

  20. Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-10-01

    Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

  1. Study of design factors of vehicle headlamp control systems; Zenshoto seigyo system no hyoka shuho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Kamishima, H; Miwa, T; Sasaki, T; Imai, M [Nissan Motor Co. Ltd., Tokyo (Japan); Sumi, T [Niles Parts Co. Ltd., Tokyo (Japan)

    1997-10-01

    The on-and-off timing of vehicle headlamp control systems varies with weather conditions. Cloudy weather has a wider light energy distribution from visible to infrared radiation than clear weather. Silicon photodiodes, which can detect visible to infrared radiation, have larger output currents on cloudy evenings than on clear evenings under the same brightness conditions. The systems should be designed with such factors in mind as spectral characteristics of windshield, filters, sensor, and eyesight. 4 refs., 9 figs.

  2. Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

    1996-02-15

    To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

  3. Ecological processes for Environmental Impact Assessment in Coastal Waters; Engan no kankyo eikyo hyoka (EIA) eno seitaigakuteki apurochi

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Kimitoshi. [Environmental Assessment Dept., Tokyo (Japan)

    1999-03-25

    This paper focuses on a method for estimating adverse effects on natural environment by economic development in coastal waters in Japan. In particular, the most critical relations concerning the impact on marine organisms is pointed out and discussed according to an environmental impact assessment. Relations between environmental impact assessment and marine organisms needs a quantitative ecological approach in order to succeed in sustainable development of coastal waters management. Recently, the Environment Agency of Japan pointed out the unreliability and the theme on accuracy and the staff for biology and ecology in the environmental impact study. Ecological response to environmental impact occurs in a wide spectrum of physiological and biological and biological functions. Therefore biological monitoring measures must correspond to the given time-space scale of natural mechanisms. For the evaluation of environmental impact, it is desire able to develop of experimental technics and collect biological and ecological basic data for the object. I Reconstructing the following: 1. Reconstructing a clearlistic EIA process by EIA agencies and practitioners, 2. Scorping the biological and ecological issues by EIA professionals, 3. Using the current computer technology, 4. Considering monitoring systems over scales of time and space for the ecological target and 5. Making available to public all monitoring data and reports of EIA. (author)

  4. Production of ethanol, fat and oil and methane gas from several crops. Sushu sakumotsu nado no energygen toshite no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Uehara, Tsuyoshi; Suganuma, Hirotoshi

    1988-05-01

    Aiming at production of ethanol, fat and oil and so on, ten kinds of miscellaneous cereal crops such as pearl-millet, soybean and so on were grown, and comparative investigation of the production rate which was considered utilization of whole plants were carried out. The suitability of vegetable wastes as methane fermentation materials for the methane gas production was investigated by the constituent analyses and methane fermentation experiments. Nine kinds of the grasses and vegetable wastes such as tomatoe buds, broccoli leaves were used for the investigation. As the results, the estimated yield of ethanol per 10 are from pearl-millet was 690 liter, the estimated yield of fat and oil per 10 are was 70 liter from soybean, The results of the analyses of nine kinds of the farm residues were as follows: (1) carbon content of about 40 %, (2) C/N ratio of 13 av., (3) C/P ratio of 91 av., and (4) the content of C,N and P was roughly appropriate. 680 to 760 milliliter of methane gas was produced from one gram of the dry matter of tomatoe bods, and in case of broccoli leaves, 424 milliliter of methane gas was produced, it was found that these values were not inferior to animal dung. (4 figs, 15 tabs, 6 refs)

  5. Evaluation of the prevention potential against landslide disasters. Jisuberi saigai wo taisho to shita bosai potential no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Umemura, J [Nihon University, Tokyo (Japan). College of Engineering; Hayashi, S; Ochiai, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1994-03-21

    In order to evaluate disaster potential and disaster prevention potential of landslides, which are complicatedly composed of natural factors and social ones, an evaluating method of the potentials is proposed by applying the multiple logistic model. Furthermore, a method making the potential map using this evaluation is shown. The multiple logistic model is based on the conception of multiple risks, and so the disaster potential is expressed with probability. The disaster prevention potential is evaluated by using the disaster potential. Taking a typical landslide district as an instance, some potential maps colored by each potential are shown. By these maps, effects of the preventive measures against disasters and changes in the disaster prevention potential according to the industrial structure as well as the population are evaluated. Furthermore, combination of the other disaster potentials obtained by changing the surveying interval or factors makes it possible to draw various disaster maps and disaster prevention ones for different purposes. 15 refs., 17 figs., 3 tabs.

  6. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  7. Study on visibility evaluation model which is considered field factors; Field factor wo koryoshita shininsei hyoka model ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakanishi, M; Hagiwara, T [Hokkaido University, Sapporo (Japan)

    1997-10-01

    The present study proposes a model to evaluate visual performance of road traffic facilities required for drivers. Two factors were employed to obtain the suitable contrast for drivers under driving situation. One factor is a suitable luminance range, which is derived from minimum required luminance and glare luminance. Another is a field. The model showed capability of providing visibility range in some cases. 8 refs., 4 figs., 2 tabs.

  8. Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

  9. Report on evaluation/selection surveys on coal species, processes and others; Tanshu process nado hyoka sentei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This program analyzes the applicable coal species centered by Australia's Victoria brown coal and Chinese coal, which are promising alternative fuel sources for Japan for their reserves, prices, availability, suitability for liquefaction, etc, in order to clarify the possible problems, and commercialize the liquefaction techniques in the early stage. This report consists of 6 chapters. Chapter 1 describes development situations of brown coal, specifically for Australia's Victoria brown coal and Chinese coal. Chapter 2 describes characteristics of the reactions involved in the brown coal liquefaction. Chapter 3 describes current status of various liquefaction processes (solvolysis, solvent extraction, direct hydrogenation and C-SRC) under development in Japan, and problems involved in their future developments. Chapter 4 describes current status of the elementary techniques, e.g., those for slurry pretreatment (e.g., dehydration and crushing), solid/liquid separation, secondary hydrogenation, product upgrading and gasification. Chapter 5 describes the related techniques, and Chapter 6 discusses the demonstration survey results of de-ashing, primary/secondary hydrogenation, and dehydration of brown coal. (NEDO)

  10. Comprehensive and Critical Literature Review on Insitu Micro-Sensors for Application in Tribology

    Science.gov (United States)

    1994-04-01

    Tsugai, Masahiro; Bessho, Mikio ; Araki, Toru; Onishi, Masayoshi; Sesekura, Takashi Source: SAE Technical Paper Series. Publ by SAE, Warrendale, PA, USA...MONITORING OF HYDROGEN ASSISTED CRACKING OF LOW ALLOY STEEL. Author. Hayashi, Yasuhisa; Takemoto, Mikio Source: Boshoku Gijutsu/Corrosion Engineering v...METALS AND ITS APPLICATION TO AE SENSOR. Author. Shimizu, Hiroshi; Watanabe, Hiroshi; Sato , Michio Source:. Japanese Journal of Applied Physics, Supplement

  11. JPRS Report, Science & Technology, Japan: Symposium on Applications of Advanced Technology: Sensors

    Science.gov (United States)

    1992-03-02

    Tokyo SENTAN GIJUTSU OYO formation of amphipathic cellular membrane compo-SYMPOSIUM in Japanese 3 Sep 91 pp 37-45 nents of procaryote , rhamnolipids A...rhamnolipid has a nonionic sugar part and an anionic cellular liposome as the matrix lipid of a biological film, carboxylic group as the hydrophilic...the phospholipids of bacterial 3. Liposome Sensor cellular membranes have no phosphatadyl choline and consist mainly of phosphatadyl ethanolamine, 4

  12. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

  13. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  14. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

  15. WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

  16. Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

  17. Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

  18. Survey of the situation of technology succession. Databases of articles including in industrial technology museums; Gijutsu keisho jokyo chosa. Sangyo gijutsu hakubutsukan shuzohin D.B. hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To promote the succession of history of and the creative use of industrial science technologies, the paper made lists and databases of the articles of industrial technology museums and material halls in Japan. Record/preservation and collection/systematization of history of the industrial technology is useful for forming bases necessary for promotion of future research/development and international contribution. Museums and material halls are the fields for making comprehensive and practical activities. The data were made as one of the basic databases as the first step for promoting activities for examining the technical succession situation in a long term range continuously and systematically. In the classification of the data, the energy relation was divided into electric power, nuclear power, oil, coal, gas and energy in general. Others were classified into metal/mine, electricity/electronics/communication, chemistry/food, ship building/heavy machinery, printing/precision instrument, and textile/spinning. Moreover, the traffic relation was classified into railroad, automobiles/two-wheeled vehicles, airline/space, and ships. Items were also set of life relation, civil engineering/architecture, and general. The total number of the museums for the survey reached 208.

  19. FY 2000 research cooperation project on plastic processing technology/quality inspection technology; 2000 nendo kenkyu kyoryoku jigyo. Plastic kako gijutsu hinshitsukensa gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of improving the production technology of plastic products in Saudi Arabia, the joint development was made of the formation technology/quality inspection technology of agricultural use and food packaging use polyolefin film optimum to environmental conditions of the site, in the light of the needs there, and the FY 2000 results were reported. In the field survey/joint study, for the xenon type weather resistant testing machine and the extruder of the inflation film forming machine which were transported from Japan, the following were carried out: confirmation of the situation of accepting them on the site, functional test of computer of the extruder, installation of the machine testing weather resistance, and the trial operation. In the domestic support study, the extrusion test at laboratory was conducted using the polyethylene resin produced on the site to acquire the basic data for formation stability. Further, the film formation test was made using the equipment with the same specifications as those of the equipment introduced to the site to study the performance of screw extrusion and the formation stability of film. Also conducted were the analytical test/quality evaluation of resin materials/film. (NEDO)

  20. Intelligent social infrastructure technology. Infrastructure technology support ultra-reliable society; Chiteki shakai kiban kogaku gijutsu. Choanshin shakai wo sasaeru kiban gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This survey was conducted to construct the core of intelligent social infrastructure technology (ISIT), and to investigate its practical application to industries and society. For realizing the ultra-safe and ultra-reliable society, it is necessary to develop the ISIT which can integrate various social infrastructures, such as architecture, city, energy, and lifeline systems required for living. For the systematization of cities, it is necessary to process and control the intelligent information by holding integrated and transverse information in common, as to logistics, lifeline, communication, monitoring, and control. For the communication engineering, the centralized systems are acceleratingly to be converted into the distributed network systems. For the mechanical engineering, intelligent control and robot technology are required. For the architectural engineering, a concept exceeding the conventional antiseismic structure idea is investigated. It is necessary to develop a new information technology providing an intelligent social infrastructures by merging the information networks and the physical world seamlessly. Necessity of ISIT is large for constructing the intelligent and ultra-reliable society consisting of these integrated and organized networks. 84 refs., 68 figs., 6 tabs.

  1. Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

  2. Evaluation report on the design of solid catalysts for saving energy in petrochemical industry; Sekiyu kagaku no tame no sho energy gata kotai shokubai sekkei hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The aim is to improve on hydrocarbon oxidation which is a difficult reaction (analogous to combustion and having potential for heat generation or explosion, with restrictions therefore imposed on reaction conditions) by use of a catalyst supporting porous membrane. The fiscal 1999-2000 results are stated. In this effort, the target reaction is promoted by a catalyst supported by a porous membrane while combustion is controlled by the said porous membrane that separates oxygen and hydrocarbon from each other. Such a design was not available since a catalyst supporting inorganic membrane withstanding so high a temperature was difficult to prepare. Recently, however, a porous membrane with its pores regulated to microstructural dimensions was developed. The activity of a Pd membrane catalyst is evaluated in view of the degree of oxidation of propylene, cyclohexene, and benzene. It is then found that hydrogen that has passed the Pd membrane participates in the reaction. In a propylene oxidation test using a membrane type Ag/Al{sub 2}O{sub 3} catalyst, it is found that acetone is generated and that oxygen after passing through the membrane participates in the reaction. Methods are studied for preparing a metal membrane in which the catalyst system comprises a catalyst supporting porous membrane and a Pd membrane. In the fabrication of metal membranes, a highly selective hydrogen permeable membrane is stably prepared by the thermal CVD (chemical vapor deposition) method. (NEDO)

  3. Environmental assessment of surfactant using aquatic microcosm system; Konuma no suiken seitaikei ni oyobosu kaimen kasseizai no microcosm system wo mochiita hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Takamatsu, Y.; Matsumura, M. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-10-10

    Microcosm system was applied to assess effect of surfactants on aquatic ecosystem. Surfactants such as LAS and Soap were added to an aquatic flask-size microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer. In the system, NOEC (no observed effect concentration) of LAS was below 1.5mg{center_dot}l{sup -1}, whereas soap was below 30mg{center_dot}l{sup -1}. Microcosm test is a pertinent tool to assess the effect of surfactant on ecosystem because microcosm test makes it possible to evaluate the effect of surfactant from a viewpoint of the interaction of microorganisms, material cycle and energy flow. With these respects, microcosm test is useful environmental assessment method which can reflect aquatic ecosystem. 10 refs., 6 figs., 1 tab.

  4. Ecological effects assessment of anionic surfactant on aquatic ecosystem using microcosm system; Microcosm wo mochiita in ion kaimen kasseizai no suiken seitaikei ni oyobosu eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Takamatsu, Y. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Kurihara, Y. [Ou Univ., Fukushima (Japan). Faculty of Engineering; Matsumura, M. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

    1997-11-10

    Microcosm system was applied to assess effect of anionic surfactant (LAS) on aquatic ecosystem. Anionic surfactant such as LAS was added to an flask microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer, comparing with that of an natural lake model ecosystem derived from natural lake water. In the flask microcosm system and the natural lake model ecosystem, biodegradation rates of LAS were almost same and NOECs (no observed effect concentration) of LAS were also below 1.5 mg{center_dot} l{sup -1}. It was found that flask microcosm test could provide precise ecological effect assessment of LAS on number of microorganisms because the system showed higher reproducibility and stability than natural take model ecosystem. It was suggested that flask microcosm test was useful ecological effect assessment method which can reflect natural aquatic ecosystem. 10 refs., 4 figs., 2 tabs.

  5. Evaluation report on the development of an advanced refrigerant for compression heat pumps; Asshukushiki heat pump yo shinki reibai kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research and development were reported on new refrigerants for compression type heat pumps. From 64 kinds of newly composed ether, CF3CF2OCH3 was developed as candidate compound substituting for CFC-11, and CF3CF2CF2OCH3 and (CF3)2CFOCH3 as those substituting for CFC-11. However, COP of the refrigeration has not been optimized. Global warming potentials were obtained by high-accuracy estimate guidelines. The new refrigerants have no chlorine and therefore no effects on the ozonosphere. Global warming effects also satisfied the present allowable values. There was no problem on human body toxicity in the short-term experiment. Costs of commercially production of the candidate compounds were trially calculated from reaction paths and chemical constitution formulae. Assuming that the raw materials are circulating on the market, plant/equipment investment, production volume, and production cost became 5 billion yen, 1000 tons/year, and 3500-6500 yen/kg in 3 persons/shift and 4 shifts, respectively. This is close to the allowable level which is ten times the CFC-12 price, 5000 yen/KG. The new refrigerants are expected to be fully commercialized in consideration of progress of the composition method and improvement of physical properties in the future. 115 refs., 37 figs., 102 tabs.

  6. Report on a survey in fiscal 1999. Survey on energy use evaluation systems; 1999 nendo energy shiyo hyoka system chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present survey and study relate to the medium to long term policies for technological development of energy and environment related technologies, and are intended to develop a system that can evaluate the importance, feasibility, expected realization time, and expected cost of the technologies, including their synergetic effects. The survey and study are intended to provide clear guidelines for planning the technological development policies on which of the technological development should be promoted in what ways, based on the evaluation given by the use of the system. The report describes in Section 1 to adopt two types of approaches of a 'technology map' and a 'network chart evaluation system' to achieve the goal. Section 2, after describing the results of surveys on the past study cases of technology evaluation, describes that the present approach has new features that are different from conventional ones. Section 3 states the results of surveys on the basic technologies to prevent global warming, and shows cases of preparing maps that notice on energy flows. Section 4 relates to network chart evaluating methods. Section 5 describes the results of surveys that have been made in relation with chronological progress of the technological development, in preparation for surveys to be made in the coming fiscal years. (NEDO)

  7. Fiscal 1998 research report on development, study and evaluation of tribo-materials; 1998 nendo tribo material no kaihatsu chosa hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Recently, needs for tribo-materials are on the increase for further energy saving and improvement of various functions and durability in various field such as less-fuel consumption car, new type Shinkansen, linear motor car, high-speed motor boat, various machines and tools, electronics, medical equipment and vitally adaptable material. This project researches and studies various properties required for tribo- materials for surface treated materials by ceramic and other material films, and clarifies the guidance and direction of the technology for creating tribo-materials by surface treatment and surface modification, through clarifying a friction/abrasion mechanism by collection of basic characteristic data and analysis of abrasion powders. This project is studying the marginal condition of film destruction for ceramic system vapor-phase deposited films, through studying the effect of mechanical properties of substrates, film surface treatment methods and film surface shapes on the marginal condition. (NEDO)

  8. Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

    Energy Technology Data Exchange (ETDEWEB)

    Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-05-01

    This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

  9. Evaluation stationariness of triaxial seismic while drilling and detection of reflected wave; Kosei kussaku ni tomonau danseiha no sanjiku kaiseki ni yoru hiteijo hyoka to hanshaha no kenshutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-05-01

    This paper reports a method to detect reflected wave components contained in an elastic wave caused in association with well drilling. Measurement was made on an elastic wave caused in association with well drilling in an experimental field by using a triaxial elastic wave detector disposed in a measurement well. Analyzing the particle motion tracks in the derived elastic wave signals (to derive the main axial direction of a three-dimensional hologram) revealed that oscillation direction of the signals changes non-steadily by time centering around the S-wave oscillation direction. In addition, a sound source position was estimated during the drilling. Existence probability of the S-wave signal in the non-steady continuous signals was estimated by handling the particle motion tracks stochastically. In addition, this existence probability was used as a weighting function for a correlative analysis to detect a reflected wave from directly reaching wave components in the non-steady continuous signals. Thus, improvement in reliability of reflected wave detection was attempted. Effectiveness of this method was endorsed by the field data. 3 refs., 7 figs.

  10. Estimation of hydrogen bondings in coal utilizing FTir and differential scanning calorimetry (DSC); FTir to DSC wo mochiita sekitannai suiso ketsugo no teiryoteki hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Mae, K.; Miura, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-28

    With an objective to know coal condensation structure which has influence on coal conversion reaction, an attempt was made on quantitative evaluation of hydrogen bonding in coal. Using as test samples the VDC made from Taiheiyo coal swollen by tetralin and vacuum-dried, and its pyrolyzed char, DSC measurement and Fourier transform infrared spectroscopy (FT) were performed. An FT spectrum comparison revealed that the VDC swollen at 220{degree}C has the hydrogen bonding relaxed partly from the original coal. However, since the change is in a huge coal molecular structure restraining space, it has stopped at relaxation of the bonding energy without causing separation as far as free radicals. On the other hand, the DSC curve shows that the VDC has slower endothermic velocity than the original coal. In other words, the difference in heat absorption amounts in both materials is equivalent to the difference of enthalpy ({Delta} H) of both materials, which corresponds to the relaxation of the hydrogen bonding. Therefore, the {Delta} H was related to wavenumber shift of the FT spectra (which corresponds to change in the hydrogen bonding condition). By using this relationship, a method for evaluating hydrogen bonding distribution was proposed from an O-H contracting vibration change that can be measured by using the FT spectra and a thermal change that can be measured by using the DSC. 3 refs., 7 figs.

  11. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Energy Technology Data Exchange (ETDEWEB)

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

    1996-10-28

    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  12. Characterization of the various catalyst for solvent hydrogenation at 1t/d PSU; 1t/d PSU ni okeru kakushu yozai suisoka shokubai no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kakebayashi, H.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    Performance of various catalysts for hydrogenation of recycle solvent was evaluated for the operation of NEDOL process 1 t/d process supporting unit (PSU). Distillate between 220 and 538{degree}C derived from the liquefaction of Tanito Harum coal was used as recycle solvent. Deactivation behaviors of catalysts were compared using a prediction equation of catalyst life, by which aromatic carbon index (fa) after hydrogenation can be determined from the fa of recycle oil before hydrogenation, reaction temperature, and total hydrogenation time. Total hydrogenation time satisfying the {Delta}fa, 0.05 before and after hydrogenation were 8,000, 4,000, and 2,000 hours for NiMo-based catalysts C, A, and B, respectively. Catalyst C showed the longest life. Used catalysts were also characterized. The catalyst C showed larger mean pore size than those of the others, which resulted in the longer life due to the delay of pore blockage. From measurements by XPS and EPMA, relative atomic concentration of carbon increased remarkably after the use for all of catalysts, which was considered to be due to the adhesion of hydrocarbons. Increase of metal atoms, such as Fe and Cr, was also observed due to the contamination of entrainment residues. Deactivation of catalysts was caused by the adhesion of hydrocarbons, and metallic compounds, such as Fe and Cr. 3 refs., 1 fig., 5 tabs.

  13. Evaluation report on the development of ultra-solid lubricant with cluster diamond; Cluster diamond wo riyoshita kotai junkatsu fukugo zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fiscal 1998-2000 results of efforts to develop cluster diamond (CD)-diffused solid lubricant composite materials expected to exhibit excellent lubrication are stated. Since friction greatly affects machine life and energy efficiency, friction reduction is an important task. Very hard and microscopic CD was utilized for the achievement of a friction coefficient of 0.08. A manufacturing technology for molds 10nm or smaller was developed, which enabled the development of a gear not larger than 8mm. The success will enable the operation of micromachines in the absence of lubrication which is impossible at present. A CD-aided functional layer creation technology was also developed. It is expected that the development and practical application of micromechanisms will make rapid progress in the 21st century. Much is expected from the creation, and goods with the achievement applied thereto, of advanced technologies whereinto non-lubrication, functional layer creation, and excellent heat conductivity are incorporated. It is quite significant that, since CD is available in any field as far as light-load low-speed sliding conditions are satisfied, sliding parts will be improved and service life will be prolonged. (NEDO)

  14. Interim report on evaluation of research and development of manganese nodule exploitation system; Mangan dankai saiko system no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This research and development project is aimed at development of the techniques which allow exploitation of manganese nodules occurring on deep sea bottoms (4,000 to 6,000 m deep) on a commercial scale, in order to secure stable supply of the non-ferrous metallic resource and improve general ocean development techniques. This project, established by the national project system, has been implemented cooperatively by the government, academic and industrial circles since 1981. Described herein are the interim results, summarized in the FY 1985. The targets of the phase for developing the individual techniques were set to develop the exploitation system design procedures, and to advance to the next phase by the end of FY 1985, where the consistent, integrated system is to be constructed and tested. The results obtained so far are satisfactory as a whole, both in the elementary techniques and their consistency. The simulations have been conducted, where various conditions are inputted to estimate the movement and exploitation characteristics of the system as a whole in the comprehensive ocean tests. It has been found that the nodule-collecting machine shows nonlinear tracking characteristics (i.e., movement different from that of the exploitation ship), and unsteady movements (i.e., repeated movements of rapid starting and stopping). (NEDO)

  15. Study on state grouping and opportunity evaluation for reinforcement learning methods; Kyoka gakushuho no tame no jotai grouping to opportunity hyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yu, W.; Yokoi, H.; Kakazu, Y. [Hokkaido University, Sapporo (Japan)

    1997-08-20

    In this paper, we propose the State Grouping scheme for coping with the problem of scaling up the Reinforcement Learning Algorithm to real, large size application. The grouping scheme is based on geographical and trial-error information, and is made up with state generating, state combining, state splitting, state forgetting procedures, with corresponding action selecting module and learning module. Also, we discuss the Labeling Based Evaluation scheme which can evaluate the opportunity of the state-action pair, therefore, use better experience to guide the exploration of the state-space effectively. Incorporating the Labeling Based Evaluation and State Grouping scheme into the Reinforcement Learning Algorithm, we get the approach that can generate organized state space for Reinforcement Learning, and do problem solving as well. We argue that the approach with this kind of ability is necessary for autonomous agent, namely, autonomous agent can not act depending on any pre-defined map, instead, it should search the environment as well as find the optimal problem solution autonomously and simultaneously. By solving the large state-size 3-DOF and 4-link manipulator problem, we show the efficiency of the proposed approach, i.e., the agent can achieve the optimal or sub-optimal path with less memory and less time. 14 refs., 11 figs., 3 tabs.

  16. Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

  17. Toxicity evaluation of chlorinated organic compounds using immortalized rat hepatocytes; Fushika rat kansaibo wo mochiita yuki enso kagobutsu no dokusei hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Sone, H; Nakajima, M; Yonemoto, J [National Institute for Environmental Studies, Tsukuba (Japan)

    1997-11-10

    Chlorinated organic compounds has high priority for toxicity screening among environmental hazardous chemicals. In the present study, we used immortalized rat hepatocytes as a liver model in vitro to evaluate the toxicity of nine chlorinated organic compounds. Toxicity of nine chlorinated organic compounds were evaluated to cellular viability of immortalized rat hapatocytes. The potency of the toxicity based on 50% inhibitory concentration (IC50) value was in the following order: triclocalban>triclosan>3,4-dichloroaniline>2,5-diclorophenol> 2,5-dichloroanisole>p-dichlorobenzene> p-chloroaniline>o-dichlorobenzene=tris (2-chloroethyl) phosphate. The rank order of cytotoxic potency of nine chemicals was compared with toxicity information using animals. The rank order of cytotoxic potency did not relative to the order referenced mean lethal dose (LD50) as an index of acute toxicity of rats or mice. However, the rank order of cytotoxic potency relatively correlated non-observed adverse effect level (NOAEL) under the exposure duration adjusted for chronic toxicity in vivo. These data suggests that the origin of testing cell had better to make match target organ of toxic chemicals for extrapolation from data of bioassay in vitro to in vivo. 16 refs., 2 figs., 3 tabs.

  18. Report on evaluation/selection surveys on coal species, processes and others. Appendix; Tanshu process nado hyoka sentei chosa hokokusho. Furoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report, consisting of 7 chapters, summarizes literature related to liquefaction of coal. Chapter 1 describes the results of the (Project Lignite), i.e., development of the concept of two-stage liquefaction of lignite. Chapter 2 describes the COSTEAM process, which uses synthesis gas (CO-H{sub 2}) as the reducing agent and coal moisture as the hydrogen source for liquefaction of coal of low degree of carbonization, e.g., brown coal. Chapter 3 describes solubilization of coal with alcohol, where coal is reacted with ethanol and NaOH at 300 to 420 degrees C. Chapter 4 describes liquefaction of coal and production of lighter products with tetrahydroquinoline as the hydrogen donor. Chapter 5 describes low-temperature carbonization as the process for liquefying coal, in particular brown coal. Chapter 6 describes possibility of development of new liquefaction techniques for brown coal, including solvolysis for liquefaction, role, recovery and reuse of catalysts, short contact time processes, and coal pretreatment. Chapter 7 describes economic viability of the secondary hydrogenation. (NEDO)

  19. Evaluation of water content in rock mass by electromagnetic and resistivity tomography. Denjiha, hiteiko tomography ni yoru ganban no gansui jotai hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, T; Inoue, M; Matsumoto, K [Kajima Corp., Tokyo (Japan)

    1993-10-31

    As a method to evaluate the rock mass, electromagnetic tomography and resistivity tomography were tested on the original site. The electromagnetic tomography can tomographically analyze the propagation velocity and initial amplitude damping. The resistivity tomography uses a finite element method from the initial resistivity distribution model and finally gives a model which is nearly equal to the actual resistivity distribution. Both the above tomographic analyses can detect the crushed spot as a low velocity, high damping and low resistivity spot. However, the electromagnetic tomography could detect finer structure than the resistivity tomography. The water content of rock mass was evaluated from the damping coefficient which was given by the amplitude damping tomography of electromagnetic wave. If it is compared with the water content which is given by the dielectric constant of velocity tomography, there partially exists discrepancy between both, because the damping coefficient contains information on cracks which disperse and reflect the electromagnetic wave. Between the resistivity and porosity, there exists a known experimental formula, which was satisfied by the presently given resistivity. 9 refs., 10 figs.

  20. Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

  1. Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

  2. Examination of optimal data acquisition for evaluation of PV systems; Taiyoko hatsuden system hyoka no tame no saiteki keisoku shuho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, H; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K; Tsuda, I [Electrotechnical Laboratory, Tsukuba (Japan)

    1996-10-27

    A 70 kW-class photovoltaic (PV) power generation system of the Tsukuba Research Cooperation Center, Agency of Industrial Science and Technology was evaluated using hourly measurement data. Hourly solar irradiation, mean PV module temperature, hourly array generated power, hourly PV system generated power were selected as the measurement items, to examine the validity of measurement method. Furthermore, based on these measurement data, the loss factors were estimated, which reduce the system efficiency. They included the losses due to the shadow effect, the deterioration of module efficiency with the raise of temperature, the mismatch of tracking control of the maximum power point, and the reduction of inverter efficiency with the input power phenomena. To estimate these loss factors from hourly measurement data, the system was evaluated by defining characteristic parameters. As a result, it was found that the main factors were the shadow effect and the mismatch loss, which reduce the mean annual output factor of the system to 65%. 3 refs., 6 figs., 1 tab.

  3. Hydrogen cracking susceptibility evaluation of buried steel pipe under cathodic protection. Cathode boshokuka ni okeru maisetsu kokan no suisoware kanjusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, Y.; Nonaka, H. (Osaka Gas Co. Ltd., Osaka (Japan)); Yamakawa, K. (University of Osaka Prefecture, Osaka (Japan). College of Engineering)

    1992-12-01

    An evaluation was given on effects of hydrogen on pipeline materials in order to determine a most base value in an optimal cathodic protection potential in cathodic protection of buried pipelines. Protection potentials were estimated from the relation between critical hydrogen amount and the potentials in marine clays and sodium acetate as electrolyte. The materials were evaluated using a strain rate tensile experiment method. The following results were obtained: The more base the potential, the elongation was somewhat less than the result in air, while the tensile strength increased slightly; difference in water content in soils varies the cross section contraction rate; the rate does not change in a marine clay containing water at 20%, but it decreases in a 30%-content soil; an SEM observation revealed pseudo cleavage faces; and the critical hydrogen amount that causes hydrogen cracking is 10 ppb, which corresponds to -1.4V in a marine clay containing water at 30%, and -1.2V at 14%. A loading experiment with actual loads verified that no fracture due to hydrogen cracking occurs even under an overprotection environment when a load imposed on an actual pipeline is kept constant. 16 refs., 10 figs., 3 tabs.

  4. Estimation of durability of GFRP laminates under stress-corrosive environments using acoustic emission; AE wo mochiita ouryoku fushoku kankyoka deno GFRP no taikyusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, Yoshimichi. [Seikow Chemical Engineering and Machinery, Ltd., Hyogo (Japan). Laboratory of Composite Materials; Nishiyabu, Kazuaki. [Osaka Prefectural College of Tehcnology, Osaka (Japan)

    1999-05-15

    The objective of this investigation is to estimate the creep life of glass fiber reinforced plastic (GFRP) under stress-corrosive environments using acoustic emission(AE). The laminates were fabricated using combinations of vinylester resin (R806) and random fiber mat or woven cloth. The creep tests were conducted in 5% nitric acid (HNO{sub 3}) environment. The AE depends on the loading level and the environment condition. For the creep test, the woven cloth reinforced specimens gave higher number of AE counts than the random mat reinforced specimens. The creep life decreased with increasing creep stress, whereas the rate of AE counts increased with increasing creep stress. A linear relationship was found between the creep life and the AE count rate. Using the proposed equation, a prediction of the creep life of GFRP under corrosive environments would presumably be possible. (author)

  5. Fault fracture zone evaluation using borehole geophysical logs; case study at Nojima fault, Awaji island; Kosei butsuri kenso ni yoru danso hasaitai no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, R; Omura, K [National Research Institute for Disaster Prevention, Tsukuba (Japan); Yamamoto, T [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)

    1997-10-22

    Ikeda, et al., in their examination of log data obtained from a borehole (2000m deep) drilled at Ashio, Tochigi Prefecture, where micro-earthquakes swarm at very shallow levels, pay special attention to porosity. Using correlationship between the porosity and elastic wave velocity/resistivity, the authors endeavor to find the presence of secondary pores, dimensions of faults, composition of water in strata in faults, and difference in matrix between rocks, all these for the classification and evaluation of fault fracture zones. In the present report, log data from a borehole (1800m deep) drilled to penetrate the Nojima fault (Nojima-Hirabayashi, Awaji island) that emerged during the Great Hanshin-Himeji Earthquake are analyzed in the same way as the above-named Ashio data, and the results are compared with the Ashio results. Immediately below the Nojima-Hirabayashi fault fractured zone, stress is found remarkably reduced and the difference stress quite small in size. This is interpreted as indicating a state in which clay has already developed well in the fault fractured zone ready to allow the occurrence of shear fracture or a state in which such has already occurred for the release of stress. 4 refs., 5 figs.

  6. Remote sensing data analysis for assessment of sea level change in Asia; Asia ni okeru kaisuijun hendo eikyo hyoka no tame no remote sensing gazo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okubo, Y; Tanaka, A [Geological Survey of Japan, Tsukuba (Japan); Kaku, M [Bishimetal Exploration Co. Ltd., Tokyo (Japan)

    1997-10-22

    Remote sensing images include information of coastal land division, sea level change such as sedimentary environment and vegetation, and distribution of artificial structures. Past sea level changes and their causes can be regionally obtained by analyzing these data and by integrating them with information obtained from geological survey. In this study, causes and history of past sea level changes, formation mechanism of coastal topography, and past sea level change survey in Thailand have been reviewed. This paper describes an extraction method of the sea level change information in coastal districts by analyzing several actual remote sensing images. For understanding the current sea level rise, it is required to clarify the causes quantitatively among three causes of sea level changes, i.e., volumetric change of total ocean water on the earth, relative sea level change due to the crustal deformation, and change of irregularity of sea surface with ocean current. It is also required to compile maps in Asian or global scales. 13 refs., 6 figs.

  7. Method of estimating time management of safety control of combustion. Nensho anzen seigyo no tame no jikan kanri No hyoka hoho

    Energy Technology Data Exchange (ETDEWEB)

    Moroboshi, M. (Yamatake-Honeywell Co. Ltd., Tokyo (Japan))

    1993-12-01

    The results of investigating time management (permissible value of ignition time and prepurge time) for safety control of combustion relating to a combustor is reported. It is shown that the heating value of hydrocarbon-based fuel is determined by molecular weight irrespective of molecular structure and constant (11200kcal/kg) per unit weight; the heating value of mixture gas of theoretical mixture ratio is constant (1000kcal/m[sup 3]) indifferently of the kind of fuel; and that the product of the heating value of a fuel and the lower limit of its explosion limit is approximately constant (400-600kcal/m[sup 3]). Succeedingly it is shown based on these values that allowable ignition time is determined by the combustion chamber load (ratio of the maximum amount, 10[sup 4]kcal/h, of combustion to the volume of combustion chamber); the effect of dilution by exhaust lengthens it by only about 50%; and that the conventional criterion that the frequency of ventilation of prepurge should be 4-5 or that the minimum time of prepurge should be 30 seconds is appropriate. 6 refs., 4 figs., 1 tab.

  8. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  9. Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

  10. Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

  11. Study on the inside gas flow visualization of oxygen sensor cover; Kashika ni yoru O2 sensor cover nai no gas nagare hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Hocho, S; Mitsuishi, Y; Inagaki, M [Nippon Soken, Inc., Tokyo (Japan); Hamaguchi, S; Mizusawa, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    In order to make clear the difference of the response time between the oxygen sensors with different protection covers, we visualized gas flow inside of sensor covers by means of two experimental methods: One is `Smoke Suspension Method` using liquid paraffin vapor as the smoke. With smoke suspension method, we detected the streamlines inside of the covers. The other is `Color Reaction Method` using the reaction of phenolphthalein and NH3 gas. With color reaction method, we confirmed the streamline inside of the cover and furthermore detected the difference of the response time of each sensor. 3 refs., 7 figs., 1 tab.

  12. Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, H; Nakada, T [Isuzu Advanced Engineering Center, Tokyo (Japan)

    1997-10-01

    The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

  13. Assessment of global environmental impacts by utilizing methodology of LCA on solar water heater for dwellings; LCA shuho ni yoru taiyonetsu onsuiki no kankyo fuka hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan); Asai, S [Yazaki Corp., Tokyo (Japan)

    1997-11-25

    CO2 emission was quantified through the life cycle of a solar water heater to assess its environment impact. Although LCA (life cycle assessment) originally sums up I/O of all materials and energy through the whole life cycle of a product to examine environment impact, this assessment was carried out for only CO2. Calculation of CO2 emission assumed a natural circulating solar water heater of 200 l in effective hot water capacity, 2.78m{sup 2} in effective collecting area, and 0.5 in average annual collecting efficiency of total solar radiation, and an auxiliary city gas heat source for compensating insufficient heat quantity. The total CO2 emission in the life cycle of a solar water heater was obtained from an industrial association table assuming the life cycles of 10 and 20 years. CO2 emission was estimated to be 5407.1kg-CO2 and 10665.2kg-CO2 for 10 and 20 years, respectively. CO2 emission due to city gas was largest in the total CO2 emission in the life cycle. As a result, for reduction of CO2 emission due to a solar water heater, improvement of equipment efficiency was most important. 6 refs., 5 figs., 3 tabs.

  14. Characteristic on photovoltaic/thermal hybrid collector. Evaluation of excergetic theory; Taiyoko netsu hybrid collector no tokusei. Exergy ni yoru hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Iwawaki, H; Morita, Y; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Described herein are characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/Ts), in which a PV module is combined with a plate-shape solar heat collector to simultaneously produce electric power and heat. Their efficiency is assessed by exergy. The test results indicate that the PV/T system gives a 1.07 times higher exergy than the PV system, 86.3 versus 80.7kWh. In terms of energy, the optimum values (OVs) are 5, 44 and 37% lower than the measuring values (MVs) for electrical energy, thermal energy and total exergy. In terms of exergy, on the other hand, OV is 5% lower than MV for electrical energy, but 893 times higher for thermal energy and 1.26 times higher for total exergy. As a result, the exergy level is 26% higher than that of a system which generates power as the main product and heat as the auxiliary product. 3 refs., 6 figs., 5 tabs.

  15. Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-08-01

    This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

  16. Evaluation of flux-trapping and magneto-resistibility of superconductors by ESR spectroscopy; ESR ho ni yoru chodendotai no jisoku hosoku to taijiba tokusei no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kusumori, T; Matsuura, K; Muto, H [National Industrial Research Institute of Nagoya, Nagoya (Japan)

    1995-09-28

    The abnormal sisal, which was observed in the ESR measurement of superconductors, was confirmed to be a non-ESR (non resonant) signal, from an ESR experiment applying parallel and vertically polarized microwave fields and from the calculation of the ESR transition probabilities. The field modulation dependence of the spectra revealed that the signal was composed of two components. From the modulation-scheme analysis and a study of type I and II superconductors, two components were assigned to the microwave responses to magnetizations trapped in the crystalline portion and at intergranular Josephson junctions. The former B and the batter J components are observed in the first derivative and absorption a form, respectively, and their polarities differently behave for the field sweep reversal. Based on these results, we have improved an ESR spectrometer, which makes it possible to measure separately two kinds of magnetization and to study the trapping ability and quantum flux. 11 refs., 12 figs., 1 tab.

  17. Economic evaluation on participation of IPP as seen from an electric power system; Denryoku system kara mita IPP sannyu no keizaiteki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kato, F.; Horibe, H.; Hayakawa, M.; Suzuki, Y.; Kaji, Y. [Nagoya University, Nagoya (Japan)

    1997-01-30

    A discussion was given on value of participation of an IPP as seen from an electric power system operation plan prepared by utilities. In the discussion, evaluation was made using as the breakeven cost of IPP power purchase prices the difference in power generation cost between electric power systems in which an IPP is participating and not participating, or in other words, the reduced portion of the power generation cost. As a result of the discussion, the following matters were indicated: in the case where an utility company expands its capacity by installing a coal-fired thermal power plant which is lower in operation cost, to deal with increase in power demand, the breakeven cost could be an avoidable cost for the utility company; if the expansion by installing a coal-fired thermal plant is not possible, the breakeven cost for a base type IPP would rise; the breakeven cost for a peak type IPP would be higher than for the base type IPP because the breakeven cost can serve to cut the peak for generators owned by the utility company; and participation of an IPP to power sources in remote areas would provide a large effect to reduce power transmission loss in an entire system, thereby increasing the breakeven cost. 1 ref., 9 figs., 3 tabs.

  18. Fiscal 1999 geothermal energy development promotion survey. Report on resource assessment for Shiramizugoe area; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Shiramizugoe chiiki shigen hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Under an assumed plan of building a geothermal power station in the Shiramizugoe area of Makizono-cho, Aira-gun, Kagoshima Prefecture, investigations will be conducted under a 4-year program into the amount of geothermal resources, the dimensions and cost performance of a geothermal power station under consideration, and the environmental impact that the locating of such will incur, through for example identifying areas containing geothermal reservoirs suitable for geothermal power generation. In fiscal 1999, activities were conducted in the three fields of (1) survey plan preparation, (2) comprehensive analysis, and (3) environmental assessment. Under item (1), a survey and coordination implementation plan was prepared, existing data were analyzed for the construction of geothermal models out of which a suitable geothermal structure was specified for digging, and a list was drafted of locations for borehole digging for fiscal 2000. Under item (2), it was found that most of the past surveys covered the Ogiri area and that the Shiramizugoe area was but poorly covered. Discussion was made on the geological structure, geothermal structure, geothermal water hydraulic structure, and the geothermal water system. Under item (3), the plan was summarily explained to the local administration, associations of hot spring hotels, and inhabitants in the vicinity, and their consent was obtained. (NEDO)

  19. Evaluation of wind noise in passenger car compartment in consideration of auditory masking and sound localization; Chokaku masking to hoko chikaku wo koryoshita kazekirion hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Kato, H. [Toyota Motor Corp., Aichi (Japan)

    1998-05-01

    Discussed is a method for evaluating wind noise in passenger car compartment based on human auditory characteristics. In the study, noise in the compartment of a passenger car travelling at a constant speed is collected by use of a dummy head, and the collected noise is analyzed in view of the masking effect, directional sensation produced by binaural hearing, etc. A masked spectrum of noise in the compartment of a 6-cylinder vehicle travelling at 120km/h is analyzed, and it is found that some frequency bands, especially the band centering on 300Hz, are masked by a loud noise component falling in a low frequency band of 180Hz or lower. By use of masked spectrum analysis, the level of noise that is actually audible to human ears can be calculated. The noise level thus determined by masked spectrum analysis and the noise direction determined by a binaural signal processing model are examined, and then it is found that the noise direction is clearly determined when the noise belongs in a 450Hz band or higher where wind noise prevails. On the bases of the above-mentioned results and the directional sensation produced by binaural hearing, a `binaural wind noise evaluation method` is compiled. 20 refs., 9 figs., 1 tab.

  20. Development of research activity supporting system. 2. Evaluation of desktop video conferencing; Kenkyu katsudo shien system no kaihatsu. 2. Enkaku kijo uchiawase hoshiki no jitsuyosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, F.; Hishitani, J.; Matsui, S. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    Desktop video conferencing (DVC) system and its software were investigated. A test system was actually constructed. Based on the test results, its practical advantage and disadvantage were illustrated. The DVC system was constructed using general LAN, and operation experiments were conducted, as to research activity. From the interview with participants and analysis of conversation history, advantage and disadvantage of this system were clarified. Performance of the trial system was examined using practical LAN, to compare with the performance of commercial systems. When using LAN, the same problems were given. It was found that the DVC system can not substitute for the conventional real face to face meeting, but it is suitable for some communication styles, for example free participation meeting or collaboration based on the same objective, which has been hard up to this time. In addition, software was made as trial, by which reservation of meeting, announcement, and calling can be carried out. 26 refs., 6 figs., 5 tabs.

  1. Fiscal 1992 report on geothermal development promotion survey (Development of geothermal reservoir assessment technique); 1989 nendo chinetsu kaihatsu sokushin chosa (Chinetsu choryusou hyoka shuho kaihatsu hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts were exerted in fiscal 1984-1992 to develop techniques for appropriately assessing a geothermal reservoir for its productivity for duly predicting the optimum scale of power generation to be provided thereby. In the development of simulators, geothermal reservoir simulators (SING-1, -2, -3) and a geothermal well 2-phase flow simulator (WENG) were developed. As for the treatment of fractures in a reservoir and of substances soluble in the hot water, the methods for dealing with them were improved and augmented. In a model field study in a Hokkaido forest, reservoir pressure continuous observation and monitoring, temperature logging and pressure logging for existing wells, and geothermal fluid chemical analysis were performed for reservoir analysis, in which both natural state simulation and history mapping excellently reproduced the temperature and pressure distributions. The temperature and pressure distributions in a natural state simulation, out of the results of an analysis of the Oguni district model field, Kumamoto Prefecture, agreed not only with those in the natural state but also with the pressure transition data in the observation well. (NEDO)

  2. Evaluation report on research and development of an ultra-advanced processing system. 3; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-08-01

    This paper describes comprehensive evaluation on the following technologies as the ultra-advanced processing system: (1) large output excimer laser, (2) high-density ion beam, (3) an ultra-precision machining device, (4) ultra-advanced processing, (5) measurement and evaluation, and (6) comprehensive test. In the item (1), research and development was performed on such technologies as output increasing, output stabilization and beam formation, having achieved the targets. In the item (2), research and development was performed on such technologies as beam convergence, plasma control, ion transportation, high-frequency quadruple pole acceleration, and large-capacity class ion beam, having achieved the targets. In the item (3), research and development was performed on form creation and ultra-precision machining, having achieved the targets. In the item (4), research and development was performed on formation of high function thin films to apply the laser abrasion process to large area, ion surface modification, wide band area optics, high reflectance optics, ion injection, dynamic mixing, and modification of ultra high-grade metal surface, having achieved the targets. In the item (5), research and development was performed on high-accuracy roughness measurement, shape measurement, optical property evaluation, a wavelength meter, ultra advanced processing standard measurement, and environment correction technology, having achieved the targets. In the item (6), comprehensive demonstration was carried out on the component technologies. (NEDO)

  3. Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

    Energy Technology Data Exchange (ETDEWEB)

    Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

  4. Interim report on evaluation of research and development of manganese nodule exploitation system; Mangan dankai saiko system no kenkyu kaihatsu chukan hyoka chukan hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-05-01

    This research and development project is aimed at development of the techniques which allow exploitation of manganese nodules occurring on deep sea bottoms (4,000 to 6,000 m deep) on a commercial scale, in order to secure stable supply of the non-ferrous metallic resource and improve general ocean development techniques. This project, established by the national project system, has been implemented cooperatively by the government, academic and industrial circles since 1981. Described herein are the interim results obtained by the FY 1984. The bases for development of the elementary techniques have been established for the comprehensive ocean tests. Bright prospects have been obtained to achieve the objectives, although there are some problems remaining to be solved. Interfaces between the sub-systems are being reviewed mainly by the persons in charge of the total system. No problem is foreseen in consistency of the individual components. The movement and exploitation functions of the test system are simulated and validated in detail, to develop the total system. It has been found by the simulations that the nodule-collecting machine shows nonlinear tracking characteristics (i.e., movement different from that of the exploitation ship), and unsteady movements (i.e., repeated movements of rapid starting and stopping). (NEDO)

  5. Report on evaluation of research and development of superhigh-function electronic computers; Chokoseino denshi keisanki no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1973-02-20

    Described herein is development of superhigh-function electronic computers.This project was implemented on a 6-year joint project, beginning in FY 1966, by the government, industrial and academic circles, with the objective to develop standard, large-size computers comparable with those of the world's highest functions by the beginning of the 70's. The computers developed by this project met almost all of the specifications of the world's representative, large-size commercial computers, partly surpassing the world's machine. In particular, integration of the virtual memory, buffer memory and multi-processor functions, which were considered to be the central technical features of the computers of the next generation, into one system was a Japan's unique concept, not seen in other countries. The other developments considered to have great ripple effects are seen in LSI's, and techniques for utilizing and mounting them and for improving their reliability. Development of magnetic discs is another notable result for the peripheral devices. Development of the input/output devices was started to correspond to inputting, outputting and reading Chinese characters, which are characteristics of Japan. The software developed has sufficient functions for common use and is considered to be the world's leading, large-size operating system, although evaluation thereof largely awaits the actual specification results. (NEDO)

  6. Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

  7. Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

  8. International cooperation project. Evaluation report on development of new oxidation and environment resistant materials for petroleum excavation; Sekiyu kussakuyo taisankasei taikankyosei shinzairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to enhance the environment and wear resisting performance of the bearing mechanism for petroleum excavation bits assuming use at a depth of 6,000 m, discussions were given on a cubic boron nitride based ultra-hard thin film and a Ti{sub x}M{sub 1-x}N based hard thin film as the new materials. This paper describes the evaluation report for the year 2000. It was found that the promising material is the Ti{sub x}M{sub 1-x}N. The practical applicability test would require a considerable amount of expense and insurance fee, while putting the material into practical use would take some more time. However, the achievements in developing this new material will allow the material to be applied to cutting tools used under the same onerous condition, and theoretical development would be possible on the consideration of the film properties, whereas further development may be expected in the future. An international joint study has performed evaluations on the environmental resistance and the characteristics of the film at the University of Toronto. These evaluations are effective in enhancing further the properties of the thin film in the future. Achievements have been accumulated steadily from starting the fundamental studies, and high level objectives have been achieved. Accurate identification has been made on the state of developing the parts for petroleum excavation bits, with the objectives set properly. Putting the bits into practical use will still require public assistance. (NEDO)

  9. Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

  10. Evaluation on reliability and safety of marine diesel engine and mechatronics. Hakuyo diesel kikan to mechatronics no shinraiseiter dot anzensei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kido, H. (Kaigi Univ., Kobe (Japan)); Hashimoto, T. (Kobe Univ. of Mercantile Marine, Kobe (Japan))

    1992-06-01

    Reliability and safety are evaluated for main diesel engines, generator diesl engines, their mechatronics and auxiliary machines on ships. The evaluation is based no statistical analysis of field data collected from outland navigation by MO diesel engine the period of 1983-1988. Evaluation indexes are used for analysis, such as failure rate (total number of failure/total navigation hour), mean maintenance man power: mh (total maintenance man power for determined period/total number of failure), manning index: MI (maintenance manpower for repairing failure occurred during 1000 hour navigation). With respect of total failure of ship plant as a whole, the failure rate decreased from 13.2 to 7.4, namely almost to half and mh was tending to increase from 5.5 to 5.8, while MI decreased from 73.0 to 43.1. With respect to heavy failure which is regarded as a scale of safety, the failure rate remained within a range of 0.7-0.5 and mh showed down-up movement like 30{yields}10.4{yields}18.8, while MI moved like 18.6{yields}5{yields} 10.9 . 3 refs., 9 figs., 3 tabs.

  11. Evaluation of building envelopes from the viewpoint of capability of controlling thermal environment; Onnetsu kankyo chosei noryoku ni yoru kenchiku gaihi no hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Umeda, K; Ono, S [Taisei Corp., Tokyo (Japan); Shukuya, M [Musashi Institute of Technology, Tokyo (Japan)

    1996-10-27

    The ability that architectural space improves the thermal environment in comparison with outdoor environment is called the `capability of controlling thermal environment.` As the value becomes higher, the indoor thermal environment is more improved. In this paper, the controlling capability of six building envelopes with different window systems was compared. The heat transfer in the wall and window system is approximated using a lumped mass model of heat capacity to obtain a heat balance equation and combined with the heat balance equation in indoor air for backward difference. The wall surface temperature and indoor air temperature in a calculation model are then calculated. A radiation absorption coefficient is used for mutual radiation on each wall. In the model, the adjoining room or first- and second-floor rooms were made the same in conditions as the model on the assumption that the one-side lighted office in an RC reference floor is in the non-illumination and non-airconditioning state. In summer, the controlling capability remarkably varies depending on the window system. For the window facing the south, the annual capability is more advanced than in other directions and the indoor thermal environment is improved on the average. 7 refs., 12 figs., 1 tab.

  12. Evaluation of performance for solar house with Trombe wall. Part 5; Trombe hekishiki solar house no hyoka kenkyu (nichisekisan Trombe heki kyuhonetsuryo yosoku senzu no teian)

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, N [Nishimatsu Construction Co. Ltd., Kanagawa (Japan); Nakajima, Y [Kogakuin University, Tokyo (Japan); Watanabe, T [Tokyo Electric Power Service Co. Ltd., Tokyo (Japan); Abe, H [Ministry of Construction, Tokyo (Japan); Yamaga, K [Mitsubishi Estate Co. Ltd., Tokyo (Japan)

    1996-10-27

    A regression equation that can calculate the daily accumulated absorption heat of Trombe Wall was given, and the performance estimated chart of Trombe Wall in which the daily unit effect of Trombe Wall can be visually recognized was proposed. The absorption heat was multivariate-analyzed by two variables of solar radiation of that day and the previous day. The data obtained from simulation was used for analysis. The absorption heat was analyzed using the meteorological data at eight spots (Sapporo, Sendai, Niigata, Tokyo, Shizuoka, Kochi, Fukushima, and Kagoshima). In this case, the result of multivariate analysis almost coincided with the simulation result. A chart that predicts the absorption heat of Trombe Wall in eight cities from the daily accumulated global solar radiation of that day and the previous day was then created as the performance estimated chart of Trombe Wall. As a result, the solar radiation of that day little influences the absorption heat when the Trombe Wall increases in thickness. Conversely, the solar radiation of the previous day significantly influences the absorption heat. In future, an equivalent heat loss coefficient will be calculated from the performance estimated chart. 2 refs., 16 figs., 2 tabs.

  13. Evaluation of the performance in the solar assisted heat pump system; Taiyonetsu riyo heat pump system no seino hyoka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y [Osaka Institute of Technology, Osaka (Japan)

    1996-10-27

    Performance of a solar heating system with a hydrothermal source heat pump was evaluated and compared with that of a direct solar heating system. The sun-dependency rates ({Sigma}D and {Sigma}H)of the direct system and heat pump (HP)-provided system were expressed as a function of the rate ({alpha}) of the auxiliary heat against the collected heat and as a function of the performance coefficient and {alpha}, respectively. When the sun-dependency rates are compared, it is found that the HP-provided system is the more advantageous when {Sigma}H/{Sigma}D>1. The relationship between the {alpha}`s of the two systems was clarified and computation was performed to compare the sun-dependency rates on condition that the two are equal in the heat collecting area. Although the sun-dependence rate cannot be elevated to 100% in the HP-provided system, it achieves a sun-dependency rate higher than that of the direct system even when the heat collecting area is small. In cases where the building is economically limited, for instance, with respect to the area for solar collector installation, it is advantageous to employ the HP-provided system. 5 figs., 1 tab.

  14. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  15. Evaluation report on research and development of an ultra-advanced processing system. Summary edition; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-08-01

    Research, development and evaluation were performed with an objective of establishing the basic processing technology and ultra-precision machining device technology utilizing large output excimer laser and high density ion beams. With regard to the large output excimer laser technology, the short wavelength excimer laser life extension technology has demonstrated ong-life operation of 1.02 times 10{sup 9} shots exceeding the final target at the initial laser output of 105 mJ/pulse. With respect to the high-density ion beam technology, the gas phase converged ion beam technology has achieved an ionic current density of 2.5 {mu}A/sr. and a beam current of 25 pA. Regarding the ultra-precision machining device technology, a large ultra-precision grinding machine of five shaft control type was developed as a final target demonstrating machine, which exhibited the shape accuracy of 0.7 {mu}m and surface roughness of 3.45nm. The surface roughness satisfied the final target. Other activities include studies on the ultra-advanced processing technology, measurement and evaluation technology, comprehensive tests, and practical application of the technologies, having derived respective achievements. (NEDO)

  16. Evaluation of indoor thermal environment with improved 65 nodes thermoreguration model; Kairyogata 65 bunkatsu taion chosetsu model wo mochiita shashitsunai onnetsu kankyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, K; Sudo, F [Isuzu Motors Ltd., Tokyo (Japan); Tanabe, S [Ochanomizu Univ., Tokyo (Japan)

    1997-10-01

    Indoor thermal environment of a vehicle was evaluated by a numerical simulation. A numerical simulation using the equivalent temperature measured with the thermal manikin was conducted. Numerical manikin was improved and convective and radiative heat transfer at each body surface was described in detail. Comparative examination using the calculation results by the numerical simulation was also conducted. 3 refs., 8 figs., 2 tabs.

  17. Interim evaluation report on research and development of robots serviceable under extreme conditions; Kyokugen sagyo robot no kenkyu kaihatsu chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development project for robots serviceable under extreme conditions are aimed at development of the robots for commercial nuclear power plants, where they are remotely controlled by the operators to implement advanced works, e.g., maintenance, inspection and repair of the facilities; supporting development of submarine oil fields, where they are remotely controlled by the operators to implement advanced works, e.g., maintenance, inspection and repair of the facilities; and for prevention of hazards at oil-producing plants, where they are remotely controlled by the operators to implement advanced works, e.g., controlling hazards, should they occur, and supporting hazard-preventive works. It is also aimed at development of the basic techniques for, e.g., those related to the system structures, and controlling and supporting the other systems. The project has been comprehensively evaluated for the achievements made so far. The individual elementary techniques for the robots for nuclear power plants, submarine oil field development and hazard prevention, and the basic techniques for these systems, are developed as planned as of the end of FY 1987 for the objects in the interim stage, based on the evaluation of the individual techniques developed before. Therefore, the bright prospects are obtained for achieving the final objectives by the end of the project period. (NEDO)

  18. Evaluation report on research and development of high-speed computation system for technological use; Kagaku gijutsuyo kosoku keisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-08-01

    The above-named project is an effort implemented under the large-scale industrial technology research and development system through the cooperation of industrial, academic, and governmental circles in the nine-year-long period beginning in fiscal 1981. The project aims to establish technologies required for putting to practical use a high-speed computation system capable of speedily dealing with huge technological problems which the computers available at the commencement of the project failed to solve. The goals set for new devices and comprehensive systems were sufficiently challenging in view of the technological level of those days, and are still at the highest level in the world. It is judged that the goals were set with reason and appropriateness. The liaison council for the implementation of the project is constituted of people of experience or academic standing, entrusted research and development activities, Ministry of International Trade and Industry bureaus concerned, and the Electrotechnical Laboratory of the same ministry. Discussion, coordination, and communication on concrete matters are under way between the constituent members, contributing to the enhancement of research and development. The liaison council activities are evaluated to be appropriate and effective. (NEDO)

  19. Development of a user interface and evaluation of an ontology for menu-based retrieval; Soho menu ni tekishita interface no kaihatsu to yogo bunrui no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Y.; Shinohara, Y.

    2000-06-01

    We have proposed the 'complementary menu system' as an easy-to-build and easy-to-use menu system. It has two component menu systems, one is based on a word taxonomy and the other is based on the document structure (e.g., the table of contents of the target document). By the user's selection of an item on a menu, the positions and relevance of related items are shown on the other menu, which makes users easier to select proper menu items. We have also shown the combination of context-sensitive menus reduces user's errors of selection of menu items by several experiments. In this report, we investigate the choice of word taxonomies effective for novice users and the design of structure and interface of menus to reduce overlooked related items. 1. Comparative experiment among a complementary menu using a general-purpose word taxonomy used in a thesaurus and the ones using domain-specific taxonomies based on quick references used in the target document, shows that even novice users prefer domain-specific word taxonomies and exhibit higher performance in retrieval significantly. 2. Comparison between a domain-specific word taxonomy that arranges different categories in a line and another domain-specific word taxonomy which reorganizes the categories under one parent category, suggests users relatively prefer the latter taxonomy but the preference depends on the amount of user's domain specific knowledge. 3. Component menu system which has only one menu showing the whole taxonomic hierarchy with scrollbars on which the positions and relevance of related items are shown is effective to reduce the number of overlooked items. (author)

  20. Corrosion control of electronic materials; Denshi zairyo no fushoku seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Y. [Hitachi Ltd., Tokyo (Japan). Mechanical Engineering Research Lab.

    1995-11-20

    Electronic materials are used in wide varieties of materials starting from hightech products like large computers, information network facilities and so forth, to vehicles, home electrical appliances, OA facilities, video game. Again, even though the part itself may be comparatively simple, high reliability is required when used in high degree system. Further, their uses irrespective to indoor or outdoor environments, are spread to wide range starting from the severe corrosive environments like coastal industrial area, drainage treatment place and so forth to low corrosive environments like general housing, offices and so forth. However, the classification of materials according to the environments where they are used is not so much carried out because preference is given to the function as an electronic part different to the large mechanical construction materials. In this report, regarding the corrosion control technology of electronic materials specially approach is made from material side, and among the various types of electronic materials, aluminium cable for LSI and magnetic materials are outlined. 37 refs., 10 figs., 2 tabs.

  1. Report for fiscal 1995 by basic liquefaction technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Delivered at the 1st meeting are a report on the fiscal 1995 research plan and an interim report, involving the use of coal-derived oils, research on refining technology using a PDU (process developing unit), reforming technology and petroleum blending technology for coal-derived oils, development of new reforming catalysts, technology of heterocompound separation, and the development of applications. Reported in relation with the development of environmentally friendly coal liquefaction technology are the study of coal liquefaction conditions, study of the upgrading of basic liquefaction techniques for the improvement and rationalization of the liquefaction process, and a project of liquefaction technology internationalization. A report is also given on a liquefaction catalyst study meeting. At the 2nd meeting, reports are delivered on the development of environmentally friendly coal liquefaction technology, including a briefing on the situation in general, designing of highly active catalysts, elucidation of the mechanism of emergence of activity, achievement of the marginal yield of coal-derived oils, and the properties of catalyst attached to coal. Delivered in relation with the use of coal-derived oils and technology for their refining are a briefing on the situation in general and reports on the blockup to occur in the naphtha fraction process and measures to counter the problem, control of the metamorphosis of active metals in reaction, heterocompound separation technology, and the development of applications. (NEDO)

  2. Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

  3. Effective utilization technology of carbon dioxide. CO sub 2 no yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Ibusuki, T. (National Research Inst. for pollution and Resources, Tsukuba (Japan))

    1991-03-12

    As carbon dioxide-related environmental measures, method was explained to chemically convert and utilize carbon dioxide. Synthesis is possible of methanol, carbon monoxide, different carbohydrates, etc. by catalytic hydrogenation of carbon dioxide, using hydrogen produced by the electrolysis of water. Task consists of heightening in both convertibility and selectivity, and abundant supply of low cost hydrogen. Methane, alcohol, etc. can be synthesized by electrochemical reducion of carbon dioxide. Because of effectively inserting multiple electron, discssion is being made of catalyst, intergrated with electrode, and electron transmitter. The photoelectrochemical reduction of carbon dioxide can be also made by utilizing photoelectric current, generated upon photoradiation on the semiconductive electrode. However, task consists of heightening in both efficiency and selectivity. Photochemical reduction of carbon dioxide, actually made by green plant, consists of oxidationlike decomposition of water and reduction of carbon dioxide. Both those reactions are skillfully separated by intermediation of very quick electron transmission system. Reduction is being studied with semiconductor, metallic colloid, enzyme, metallic complex and other various catalysts. 10 refs., 3 figs., 4 tabs.

  4. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy (Textile technology field)); 1999 nendo choki energy gijutsu senryku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a textile technology field. Social demand and constraint in the 21st century restrict human life and industrial activity, however, include huge business chances. This technology strategy aims at construction of textile business contributing to the society, and improvement of the international competitiveness of Japanese textile industry. Analysis was made on the current international competitiveness of the textile industry in comparison between Japanese and American productivity. As factors hindering technological innovation, the following were pointed out: poor cooperation among industry, academia and government, poor cooperation among different kinds of industries, poor preparation of basic technology, knowledge base and creation base, and poor deregulation. As the future target and strategy, 7 technology targets, 2 creation targets, and every target year were showed. 4 proposals were also showed as follows: preparation of a technology base, creation base, talent education and knowledge base, and protection of intellectual property rights. (NEDO)

  5. Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

    2000-03-24

    Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

  6. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  7. Technical issues and a prospect of ICAI. Chiteki CAI no gijutsu kadai to kongo no doko

    Energy Technology Data Exchange (ETDEWEB)

    Otsuki, S. (Kyushu Institute of Technology, Kitakyushu (Japan))

    1992-12-10

    This paper explains technical issues and a prospect for intelligent computer assisted instruction (ICAI) which combines the intelligent tutoring system (ITS) with an open-ended (discovery) type education system. The paper summarizes the ITS characterized by modelling students based on error-origin diagnostic technologies; various functions that have been realized for the first time therefrom; different methods for error diagnosis and error-origin diagnosis; and criteria to evaluate these methods (evaluating generality, coverage, and tractability). The paper indicates that no complete diagnostic methods have been obtained according to these criteria, that, therefore, an issue of incompleteness in the student model still remains, and that unsolved issues in the ITS include some that exceed the framework of the ITS. Also mentioned in the paper are that the discovery type education system has a possibility of realizing an education with new quality, and that a new attempt is being performed to merge the ITS with the discovery type education system. 17 refs., 2 figs.

  8. FY1995 generic supercritical water technology; 1995 nendo generic technology to shite no chorinkai riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the establishment of the basis of supercritical fluid technology, we perform elucidation of the specific feature of the supercritical fluid as a reaction media and development of some new process. In this study, we first studied the fluid structure of SCF through in-situ spectroscopy and MD simulation. As a result, significant hydrogen bonding amongst water molecules and a solvation structure around the solute were observed in the supercritical state. This fluid structure has new features different from that of high temperature steam or liquid water. We found that this is closely related to the difference of bulk properties of SCF and local one around the solute. On the basis of these fundamental findings and with the better understanding of the specific features of SCF as a reaction media, development of some new process had been conducted more efficiently and successfully. The processes being developed in this study include 1) waste biomass and plastic conversion to recover chemicals, 2) hydrogenation of heavy oil for desulphurization through partial oxidation 1 and 3) hydrothermal synthesis of metal oxide fine particles. (NEDO)

  9. Technical features of steel structure construction by Kawasaki Steel; Kawasaki Seitetsu no kokozo gijutsu no tokucho

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, T.; Urata, I.; Okata, S. [Kawasaki Steel Corp., Tokyo (Japan)

    1996-03-01

    In the steel structure technology of Kawasaki Steel, the joint technique (e.g., welding) is added to them while developing or improving the products that meet the social needs as a material supplier. Moreover, the execution technique that manufactures materials or constructs them as an integrated structure, the structural analysis that conforms to the function and application of a structure, and the design technique on dynamic properties or durability such as earthquake resistance, fatigue, and corrosion resistance are synthetically expanded for engineering. In this paper, a building steel frame, non-residence building, bridge, and harbor structure as steel structure in the building and construction fields were described for each structure genre. The structural technology of a building steel frame is summarized to the products of pillar materials. An earthquake brace, using a dead soft steel, with high earthquake energy absorption capability and a damping wall were also developed. The design and execution technique of a large roof was systematized. The exchange technique of a road bridge RC floor and the technique of an unstiffened suspension bridge for pipeline were developed. A new technique was also developed for a suspension monorail track and offshore structure. 30 refs., 5 figs.

  10. How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

    Energy Technology Data Exchange (ETDEWEB)

    Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

    1999-07-05

    They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

  11. Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

  12. Plant growth regulation by the light of LEDs; LED ko wo tsukatta shokubutsu saibai gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, H. [Mitsubishi Chemical Co., Tokyo (Japan). Yokohama Research Center

    1996-03-01

    Light Emitting Diode (LED) has not only an excellent display function for the luminescent device but also a superior feature without other lamps as light source for plant growth. It was National Aeronautics and Space Administration (NASA) to find out such merit for this light source for plant growth and try at first to use for plant growth at the space. They began to examine the LED application to the light source for the plant growth at the space since a stage at high cost of the LED, to develop some researches centered at cultivation of lettuce, wheat, and others. Finding out future possibility of cost-down of the LEDs on the cost/performance and large merits of the LEDs for control of the plant growth and plant physiology, authors have conducted some cultivation experiments of the plants using the LEDs for light source some years ago. In this papers, characterizations, actual possibility, and future developments of the LEDs for the light sources of the plant growth, are introduced. 5 refs., 4 figs.

  13. Comprehensive research cooperation in environmental technology in fiscal 1995; 1995 nendo kankyo gijutsu sogo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Cooperative study was conducted on research subjects concerning water pollution preventive technologies in China and Thailand. In China, straw pulp mills were studied which were in the Institute of Light Industry Environmental Protection and the Environmental Engineering Course of Jinghua University. The following studies were jointly conducted: survey of the water quality pollution caused by waste water, investigational study on production technology and waste water treatment technology, extraction of technologies effective to preserve water quality, study/evaluation of economical efficiency of the said technologies, etc. In Thailand, cooperative research was conducted on automatic measuring technology for factory waste water in a model industrial estate of the Thai National Industrial Estate Corporation. Items for the study were a study on measuring technology for water quality environment, an investigation on the status of water quality environment in the model industrial estate, a study on automatic measuring technology for plant waste water, a study on how to use measuring data in the model industrial estate, etc. Every study enabled technical data accumulation at every research institute through field research exchanges. 24 refs., 91 figs., 45 tabs.

  14. Rear impact whiplash neck injury reduction technology; Jidosha komen shototsu ni okeru muchiuchisho teigen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y.; Ichikawa, H.; Kayama, O. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1999-11-01

    Even though whiplash neck injuries suffered in low-speed rear impacts are one of the major concern in traffic accidents, the mechanism of the injuries is not fully understood at present. Hence, the countermeasures have not been clear, yet. The bio-mechanical research was done to understand the injuries and three different modes of occupant's motion related to the mechanism were found. Based on this research, Nissan Active Head Restraint has been developed to reduce whiplash neck injuries in low-speed rear impacts. (author)

  15. Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

  16. Future trend of science and technology. Kagaku gijutsu wa doko made susumu ka

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, S. (Inst. for Future Techynology, Tokyo (Japan))

    1991-01-05

    The fifth survey of a large scale technology forecast which is conducted by the Science and Technology Agency (Japan) is now started. This paper gives a prospect on the megatrend of technical innovation according to the 4th. Survey conducted in 1987. Threefold viewpoints of the analysis are as follows: Type of the technical innovation (Breakthrough type and technology melting pot type). New technology and new product development (adding higher value, human friendly type). Leading technology qualitative innovation of information/electronic technology; pursuit of highly intelligent technology. (Biological technology qualitative innovation of bio-technology: pursuit of simulated organism function). The technical forecast is conducted on 17 field sectors. Examples of design-synthesis and fabrication'' technology are a technology of control based on clarification at atomic and molecular levels'', and another is design and synthesis technology of substances by means of a computer science:.'' 2 tabs.

  17. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  18. Disinfection technology with ozone for cryptosporidium; Cryptosporidium taisaku to shite no ozone shodoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Y.; Takahashi, K. [Fuji Electric Co. Ltd., Tokyo (Japan); Motoyama, N. [Fuji Electric Corporate Research and Development, Ltd., Kanagawa (Japan)

    1998-06-10

    Measures against Cryptosporidium parvum (C. parvum) in the waterworks are discussed. C. parvum is a pathogenic protozoan, and exists in the form of oocyst protected by a hard shell. It does not multiply in water or food, but does in human intestines and causes violent diarrhea and bellyache. A grave concern was created when many people were infected with the protozoan via tap water in Japan and the United States. Under such circumstances, ozone is used in an experiment to inactivate C. parvum. It is found that the C. parvum oocyst inactivation effect is evaluated by using a Ct value (disinfectant concentration Cmg/Ltimescontact time in minute) and that ozone treatment inactivates 90-99% of the protozoan. When various advanced water treatment technologies are being introduced for the purpose of serving safe and tasty water, the outcome of this study conveniently offers an ozone treatment method that will additionally inactivate pathogenic protozoa. Studies will be continued to elucidate the effects of factors of ozone treatment and water quality for the completion of an ideal disinfection process. Reference is made to an example of disinfection work implemented at a water purification plant of Milwaukie City, United States. 9 refs., 6 figs., 4 tabs.

  19. Earth-friendly refuse processing. Chikyu kankyo wo kangaeta gomi shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishigaki, M. (Takuma Co. Ltd., Osaka (Japan))

    1994-06-15

    This paper contains six articles: (1) Earth-friendly Garbage Disposal, (2) Erasable Copy Machine, (3) Making Plastics from Shell of Crustacean, (4) From Garbage into Petroleum, (5) Utilization of Sewage Sludge for a Recycle-type Society, and (6) FRP Boat Disposal Technology. All articles address the latest topics about disposal of wastes and garbage that have been attracting general attention in environmental issues. The article (1) presents the latest waste incineration technology, garbage power generation, and disposal and utilization of incineration residues. The article (2) is about a prototype of the copy paper regeneration device (toner remover) developed and produced by Ricoh Co., Ltd. The article (3) describes biodegradable plastics using chitin and chitosan that can be acquired from shell of crustacean. The article (4) describes how to extract oil or gas from plastic waste through its thermal decomposition. The article (5) presents volume reduction and utilization of sewage sludge. The article (6) presents disassembling and disposing waste plastic boats that have been rapidly increasing. 8 refs., 27 figs.

  20. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  1. Prospect of concrete technology; Kenchiku ni okeru korekarano konkurito gijutsu no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Tadahiko [Shimizu Corp., Tokyo (Japan)

    1999-10-10

    The privatization of state-owned companies, the abolition of the protectionism to domestic industries and the market liberalization, deregulation to the economic activities or movement to abolition of regulation were concretely made a start. Moreover, the reform of the social life was also requested with an increasing of international global environmental preservation. These reform influences in the construction industry have been affected and could not ignored in consideration of the development in the 21st century. In this paper, the summary of reform in development, construction industry; especially the correspondence in the construction industry and the relation to concrete technology from now were described. Especially, concerning establishment of concrete technology, it was given as the construction of the safe and comfortable space, highly production technical development, countermeasures to resource-saving and environmental preservation, search of new concrete materials, development of the renewal technology and correspondence to large project. (NEDO)

  2. Emerging technologies for demand side management. Demand side management jitsugen no tame no saishin gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Iyoda, I [Mitsubishi Electric Corp., Tokyo (Japan)

    1993-11-05

    This paper explains the latest situation in hardware technologies to realize the demand side management, divided into the following technologies: communications technology, measurement technology, client information system technology, load controlling technology, home automation technology, and energy storing and saving technologies. Speaking of the communications technology, information exchange between the supply side and the demand side is important in the demand side management, whereas a technology intended of automatic power distribution and automatic meter-reading is advancing in development. The technology covers transmissions using from power lines and telephone lines to optical cables and wireless communications. Power line communications using power transmission lines as communication lines are simple and economical, but weak against noise, and not suitable for long-distance communications. Wireless communications have been drawing attentions along with the development of mobile communication device technologies. These technologies will give benefits to electric power companies in the initial stage of their use, such as for load investigation and general automation in power distribution. They would shift to benefiting users in about 2010 covering from security information such as about power interruption to publicity information and educations. 8 refs., 8 figs., 1 tab.

  3. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Aerospace technology field (Aircraft technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kokuki gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of an aircraft technology field. In an aircraft field, since the major theme is application of new technologies to new airframe development, with joining in international cooperative development of aircraft, Japanese initiative development of airframes based on the domestic market demands and profitability should be started as early as possible. Because there is no airframe development by only one country including U.S.A., Japan is profitable to unite with some overseas companies, and invest selectively in specific leading fields. Positive technical support to safety, reliability, comfort and environment harmony are also important. More important theme than establishment of elementary technologies is preparation of an integrated flight demonstration system to expand application chances of development results, and preparation of various test facilities for tests required during development activities. Application of information technologies to the whole aircraft industry, and organic cooperation between the private and public sectors are also important. (NEDO)

  4. Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

    1994-07-25

    With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

  5. Advanced technology trend survey of micromachines in Europe; Oshu ni okeru micromachine sentan gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this research survey, the development trend of micromachine technology in Europe was surveyed, development level of micromachine technology of European companies was grasped, and practical application fields of their target were investigated. Technology development level of private companies in Japan`s national projects and practical application fields of Japan`s target were arranged. Trends of micromachine technology development are compared between Japanese companies and European companies. Among micromachine technology development projects in Europe, ``8520 MUST`` is a part of the ESPRIT Project. About 40,000 companies among about 170,000 companies in whole Europe are relating to the MUST Project. The main fields include the manufacturing technology, process control of machines, technology of safety, sensor technology in environmental fields, and automotive technology. The marketing fields of application include the automobile, military technology, home automation, industrial process, medical technology, environmental technology, and games. The results can be compared with the direction of research and development in Japan. 22 figs., 8 tabs.

  6. Present status and prospect of the pneumatics; Kukiatsu gijutsu no ayumi to kongono kenkyu no kadai

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, S. [Waseda University, Tokyo (Japan). School of Science and Engineering

    2000-05-15

    This paper describes course of pneumatic technologies and problems in future researches. Pneumatic systems are inferior to electric and hydraulic systems in terms of efficiency. It is because electric power is converted into fluidized energy by using a compressor, and then converted to mechanical energy by using an actuator. When theses published from 1990 through 1999 are put in order, the research objects are accounted for half by control related technologies, and researches related to elements account for only one third. This paper enumerates assignments to be tackled positively in the future by utilizing compressibility of air in pneumatic systems, and features of high speed drive utilizing the stored energy instantaneously. Application of air pressure to robotics from the demand of the aging society, and pneumatic tools having intelligent functions must be subjected to new contrivances. These will serve for work assistance systems to enable aged people to perform works, and for activating industries including organic agriculture. Tools in this sense may include impact wrench, and others. Furthermore, development of fundamental studies for 'why air pressure?' is demanded strongly, including the viewpoint of LCA in the recycling type society. (NEDO)

  7. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  8. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  9. Manufacturing technology for advanced jet engines; Jisedai jetto engine no seizo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirakawa, H [Kawasaki Heavy Industries Ltd., Kobe (Japan)

    1997-04-05

    A part of the latest production technologies for aircraft jet engines is introduced. Outline of the turbofan engine, turbo-prop engine, and turbo-shaft engine are given. Every one of them employs a gas turbine engine comprising a compressor, combustor, and a turbine as the output generator. Increase in the turbine inlet temperature is effective for making the gas turbine engine more efficient. The development tread of heat resisting materials for realizing higher temperature is shown. The current status and future aspect of the manufacturing technology is discussed for each main component of the engine. Technological development for decreasing weight is important because the weight of the fan member increases when the fan diameter is increased to increase the bypass ratio. FRP is adopted for the blades and casing to decrease the weight of the compressor, and studies have been made on fiber reinforced materials to reduce the weight of the disks. The outlines of the latest manufacturing technologies for the combustor and turbine are introduced. 2 refs., 9 figs.

  10. Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-09-01

    Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

  11. Investigations on an environmental technology transfer information network; Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With developing countries (APEC countries) as the main objects, investigations were carried out to issue environmental technology transfer information that Japan has accumulated, and advance exchanges of technical information with persons related inside and outside Japan. As a result of the investigations, it was found that the environmental technology information that serves more effectively for the developing countries is the technical information that has been developed by repeating improvements, has provided actual results in work sites, and is actually used, rather than the state-of-art technologies. Based on this result, business entities having factories and operation centers located in Mie Prefecture and the city of Yokkaichi were asked to provide data for the actually used environmental technologies. Out of 51 items provided by 17 companies, nine items were selected to be used as prototype database materials for an information network. The objects of information sources will be expanded to a nationwide scale in the future to improve the contents of the database. Problems of handling information copyrights and technical know-hows were presented in the course of data collection, urging the necessity of due considerations on the matter. Necessity was indicated on maintenance and management of data base as well as its quantitative expansion. 1 ref., 4 figs.

  12. FY 2000 report on the survey on the long-term energy technology strategy. Fundamental survey to work out industrial technology strategies (technology strategy by field - material technology field); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of constructing the material technology strategy, conducted were study of the trend of technical development, arrangement of material technology seeds, and survey of the R and D environment. Concretely, the paper carried out the grasp of the national projects related to materials in Europe and the U.S., patent registration (U.S.-Japan comparison)/application (Europe/Japan), transfer of technology trade, and survey of the trend of papers made public in scientific magazines. Further, in the survey of the R and D environment, conducted were how to treat researchers/engineers, how to handle intellectual ownership, system to promote the cooperation among industry/university/government, and comparison among countries in policies of technology such as patent strategy. The results of the survey were classified into the following 4 items: 1) trend of the technical development in the material technology field; 2) developmental environment in the material technology field; 3) competitive force in the material field and material user needs/seeds maps; 4) proposal for the material technology strategy. As to the competitive force of material technology in 3), the paper took up organic/polymer, iron/steel, aluminum, semiconductor, and ceramic materials. (NEDO)

  13. Survey of the development of industrial technology in Japan; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Conditions for creating Japan`s type technologies have been investigated by extracting technologies and experiences meriting the succession to the next generation among the industrial technologies in Japan after World War II. Technological creativity of Japan began to appear from the 1970`s. Quartz watch of SEIKO, U-Matic VTR of SONY, ladle refinery method of DAIDO Steel, PAN-based carbon fiber of TORAY, continuous annealing of Nippon Steel, calculating machine using liquid crystal of SHARP, ASA-400 high sensitivity film of FUJI FILM, and Japanese word-processor of TOSHIBA are the examples. The basic ability to create those products and technology lays in the diversity of firms in electronic device and fine machinery industries consisting the boundary between general and electrical machinery, the systematizing ability and inter-industrial cooperation which were promoted through quality control, automatization of assembly and production control by computer, and the research and development capability which has been brought up during the high economic growth as a learning process of technology. The society and industries have to make efforts to create the new creative conditions for younger generations. Otherwise, Japan`s technology will not develop. 134 refs., 19 figs., 8 tabs.

  14. Laser materials processing as manufacturing technology; Seisan gijutsu to shite no laser kako

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, I. [Osaka University, Osaka (Japan)

    1998-11-01

    This paper describes the laser material processing. Laser is artificial light that uses the amplification based on the induced emission of light. It is very excellent in directivity and monochromaticity. The high power density and concentration characteristics of laser enable a variety of high-performance processing such as junction, removal, reforming, and addition. Excellent controllability (that facilitates the automated processing), transmission performance (the processing by energy transmission in long range space is most suitable for laser), and non-contact processing (that contains no wearing, noise, and contamination) are great advantages that the existing processing method does not have. In the wide wavelength area between ultraviolet and infrared areas, the laser that can be used for material processing is very wide over the range of the continuous oscillation to the ultra short pulse of a nanosecond order. The thermal processing accompanied by melting and evaporation as well as the non-thermal processing (quantum processing) by a photochemical reaction is also available as the type of processing. The processing used for manufacturing technology is almost thermal processing including removal, junction, reforming, and addition. The thermal processing covers the range of electronics to heavy industry. 29 refs., 12 figs., 2 tabs.

  15. Information communications technologies that surpass the global communications network. Sekai tsushinmo o koeru joho tsushin gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    1990-05-01

    Development of information communications technologies that surpass the global communications network is being pushed forward in order to establish the global village that McLuhan foretold in 1964. Effects of hybrid intensification with the intensification of communications technologies and computer technologies have become evident as facsimiles, automated teller machines of banks, home videos, automatic response telephones with synthetic voices, compact disks, portable telephones, video games and high-definition televisions were developed and put to use in a wide range. Intensification and integration of computer technologies and communications technologies has every possibility, but it also has a peculiar aspect of lacking guiding principles. Uncertain factors of the values of informations in the market are ever increasing, and their true values are yet to be found. Anyhow, it is a long way to the goal of the global village.

  16. Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-03-01

    The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

  17. Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

  18. Study of the O2/CO2 combustion technology; Sanso nensho gijutsu ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, M [Center for Coal Utilization, Japan, Tokyo (Japan); Kiga, T; Yamada, T [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Arai, K [Nippon Sanso K.K., Tokyo (Japan); Mori, T [Inst. of Research and Innovation, Tokyo (Japan); Kimura, N; Okawa, M [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    This study is being progressed during a period from 1992 to 1999 as part of the NEDO`s clean coal technology program. This paper describes what has been discussed to date. The absorption method and the adsorption method may be used to recover CO2 as means to deal with the problem of global warming resulted from burning coals. These methods, however, have problems in economy caused from concentration of CO2 in flue gas being low. The present study is intended to raise the CO2 concentration in flue gas by using oxygen plus circulated flue gas in the place of combustion air, so that CO2 may be recovered as it is without being separated from the flue gas. Therefore, an oxygen-blown pulverized coal fired power generation plant having a cryogenic oxygen manufacturing equipment was designed to discuss the plant operability and economy, and the pulverized coal combustion technology by using a dynamic simulation. A large number of findings have been obtained already, and the study has reached a level at which grasping the whole image is now possible. 13 figs.

  19. 6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

  20. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  1. Fiscal 1995 report. Liquefaction key technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The subcommittee held the 1st meeting in September 1955 and the 2nd in March 1996, when fiscal 1995 research plans and research results were introduced and deliberated. In the study for designing a high-dispersion catalyst and the elucidation of the mechanism of activity expression, catalysts of highly dispersed iron supported on the brown coal surface in various ways were compared with each other in terms of liquefaction activity. Furthermore, geometric changes in the iron catalyst during the sulfurizing process were examined using the XRD (X-ray diffraction) and TEM (transient electromagnetic) methods. An improved catalyst was found to achieve a liquefaction yield near the Yallourn coal liquefaction limit in a high boiling solvent system. Concerning the study of coal oil product applications and refining technologies, reports were delivered on research results relating to the problem of blocking to occur during naphtha fraction refining and measures therefor, inhibition of active metal geometric changes during reaction, methods for separating hetero-compounds from coal oil and application thereof, and so forth. (NEDO)

  2. AI technology and automobile. ; Toward vehicle autonomy. AI gijutsu to jidosha. ; Sharyo no jiritsuka ni mukatte

    Energy Technology Data Exchange (ETDEWEB)

    Okuno, A. (Mazda Motor Corp., Hiroshima (Japan))

    1991-01-01

    This report describes the vehicle autonomy by using artificial intelligence (AI) technology. Owing to a remarkable progress of AI technology, it is forecasted that driving support system will be introduced into the market till 2000, and higher autonomous navigation system will be introduced since about 2010. Autonomous vehicles have capacities of recognizing the outside world and of navigating roads by themselves, and with their enfanced environment adaptability the road transportation in the future is expected to be much more safer than in the present. The autonomous vehicle can warn its driver of potential dangers and correct operational errors of the driver. In order to realize such autonomous vehicles, extensive researches on perception systems, decision making systems and driving support systems are needed. 9 refs., 10 figs., 1 tab.

  3. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  4. Domestic and overseas situations of Japanese automobile industries; Jidosha gijutsu. Jidosha wo torimaku shojosei

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, H. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1998-08-01

    The economic circumstances in 1997 are characterized by a high rule in the United States, slow developmental trend in Europe and lagging situations in Asia. The political and economic situations of main counties in the world are summarized with indication of Japanese dull activities, financial crisis and their countermeasures as well as the trade friction in 1998. The number of cars sold in Japan decreased to 3.71 millions in 1997 from 4.55 millions of 1996, while cars imported amounted to 360,000 in 1997 (-14.7% compared to that of the preceding year), the number of exported cars were 4.55 millions as compared to 3.71 millions in the preceding year, namely about 23% increase, of which 1.41 millions for North America and 1.25 millions for Europe. Other evolutional facts are also presented zone by zone. Then, questions which the Japanese automobile industries are faced to are enumerated and explained. The overseas production bases and their activity trends are mentioned, focusing on the modular production system as well as the lean production system as for the international expansion of the products, whereas market strategies with direct injection engine, low emission, hybrid car and so on are described in terms of technical development. Lastly, and innovation of physical distribution tat takes place in the United States such as a movement to a larger scale dealer system, car dealing business through internet and so forth are mentioned including the Japanese trials in line with these matters forecasting an ever-intensive concurrent. 5 refs., 5 tabs.

  5. International Symposium for the Promotion of APEC Environmental Technology Exchange; APEC kankyo gijutsu koryu sokushin symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-11

    The International Symposium for the Promotion of APEC Environmental Technology Exchange was held under the theme `The function and role expected of the APEC Virtual Center,` with the objectives of clarifying the need for future intra-regional environmental technological exchange, defining the types of information and personnel exchange, and promoting the use of interactive character of the APEC Virtual Center for Environmental Technology Exchange by encouraging access to and participation in the Virtual Center project. It was held in the period of 11th and 12th, November in 1996, at the venue of Rinku International Convention Center in Osaka. The symposium was attended by 477 persons from nine countries, i.e., Australia, Canada, China, Indonesia, Korea, Philippines, Thailand, the US, and Japan, comprising staff members of intra-regional environment-related organizations. After the keynote speech, `Current status and tasks of environmental technology exchange`, and `Expected roles of the Virtual Center for Environmental Technology Exchange` were discussed. During the plenary session, the chairman summarized the symposium. This summary was carried on the Virtual Center homepage of the Internet

  6. Fiscal 1994 report. Liquefaction key technology subcommittee; 1994 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The subcommittee held the 1st meeting in August 1994 and the 2nd in March 1995, when preceding fiscal year's research results, fiscal 1994 research plans, fiscal 1994 research results, etc., were introduced, and deliberated. In the study of hydrorefining of naphtha, kerosene, and light oil fractions, a nitrogen concentration level of not more than 5 ppm was achieved by refining oils from Indonesian coal. Studies were also made about the two-step hydrorefining system, the relationship between the coal oil refining level and sludge formation, etc. In the research for the development of novel catalysts for upgrading coal oil, the active life of a nickel-supporting catalyst for hydrogenation at the 1st step was somewhat prolonged with an increase in the amount of nickel. In the study of coal liquefaction conditions, an AWIP method was deliberated, wherein liquefaction process waste water was utilized as one of catalytic component adjusting materials. For upgrading liquefaction key technologies, studies were made for catalyst improvement and pretreatment method development, and about the behavior of liquefaction reaction in a high boiling solvent-aided process. (NEDO)

  7. Expectation of rapid prototyping; Rapiddo/puroto taipingu gijutsu no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Kishinami, T. [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering

    1997-04-05

    Prototyping can be defined as the physical and imaginable product model formation process used for verification of production guideline of functional component. Rapid prototyping means the combination of technology forming directly the physical model from CAD data. It is a summarization of technology composed of design assistant technology, model production technology, and integration technology. In 1980`s, 3D System Corp. proposed the stereo lithography. Since then its research and development were promptly carried out as for the technology of rapid formation o physical model. Resultantly, it became possible to fabricate the model designed by the three dimensional CAD within a day using a rapid prototyping system. This can be roughly divided into the following three: (1) stereo lithography, (2) method of melting and hardening by laser irradiation of the powder plastic and wax, (3) 3D-printing method consisting of selectively coating of ceramic powder with binder. 4 refs., 3 figs.

  8. Alternative disinfection technology for water purification systems; Josui shori ni okeru enso daitai shodoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, T. [The Institute of Public Health, Tokyo (Japan)

    1998-09-10

    This paper describes chlorination substituting disinfection technologies used in water purification systems. Chloramine treatment is regarded as effective in reducing trihalomethane (THM). Chlorine is injected in the initial stage in the form of free chlorine to disinfect pathogenic microorganisms in a short time, which is then added with ammonia to convert it into chloramine for further utilization. Chlorine dioxide has not been used in Japan, but introduced in Europe and America to treat THM. Ozone has the strongest oxidizing power, and is used for disinfection, virus inactivation, decomposition of THM precursors, and removal of fungus odor. The ozone treatment will produce aldehyde if an organic matter is present, but aldehyde can be removed by treatment using organismic activated carbon. Ultraviolet ray treatment has an advantage of being difficult of producing byproducts. This system was experimentally compared with free chlorine treatment on disinfection effect, mutagenicity, suppression of producing THM byproducts, and odor removal. In order to assure reliability of microorganismic and chemical safety in tap water supply systems, assurance by considering the entire system is important, not only by operating the disinfection units, but also combining such physical water purifying technologies as coagulation, sedimentation, filtration, and membrane treatment. The use of chlorine substituting disinfectants is also a part of the conception. 6 refs., 8 figs., 5 tabs.

  9. CMOS analog integrated circuit design technology; CMOS anarogu IC sekkei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Fujisawa, A. [Fuji Electric Co. Ltd., Tokyo (Japan)

    2000-08-10

    In the field of the LSI (large scale integrated circuit) in rapid progress toward high integration and advanced functions, CAD (computer-aided design) technology has become indispensable to LSI development within a short period. Fuji Electric has developed design technologies and automatic design system to develop high-quality analog ICs (integrated circuits), including power supply ICs. within a short period. This paper describes CMOS (complementary metal-oxide semiconductor) analog macro cell, circuit simulation, automatic routing, and backannotation technologies. (author)

  10. Noise and vibration improvement technologies for engines; Engine ni okeru soon shindo kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Kuzuoka, H.; Maeda, R. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1999-02-01

    This is an outline of recent measurement and simulation technology for reduction of engine noise and vibration. We can recognize correct phenomenon by visualization of noise and vibration phenomena using new measurement technology. And we can create optimum countermeasures using new simulation technology In this report, examples of application of these technology in the development of NEO-DI engines are provided. (author)

  11. Process improvement technology for petrochemical plant; Sekiyu kagaku puranto ni okesu purosesu kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Shin

    1999-05-05

    Before, GTC technology Co. was a manufacturer of the tray as a Greenwich technology. It is the subsidiary, which undertakes technology and licence of the engineering firm in U.S.A. at present. It carries out besides the technology licence support in the startup for the prolonged driving of technical service, operating condition of the plant of improvement and optimization and, etc. Has made separation and purification technology, which made extractive distillation to be a beginning good and has the process improvement technology to the PTA (high-pure terephthalic acid) from BTX (benzene toluene xylene) of petrochemical plant. (NEDO)

  12. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Iron and steel technology field; 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) (tekko gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a steel technology field. Japanese steel industry should correspond to requirements of the international economic society as the top runner. Although it is now difficult to suppose a basic technology innovation, stable supply of basic materials is necessary for peripheral industries. The basic raw material technology is the basis of domestic and overseas socio- economic activities. The technology development support system to retain the world-wide leadership of Japanese industries is a strategic issue. Preparation of cooperative R and D bases of industry, academia and government along a national policy is important. Strong promotion of such national projects is also essential as global environment problem, positive use of advanced information tools, development of technologies and products of unexplored fields, and development of new products and demand creation according to social needs. Such measures along social requirements are also important as raw material development to double an energy efficiency, and the policy and system to construct a recycling society and living spaces. (NEDO)

  13. Visualization techniques in diesel engine research. Diesel Engine kenkyu ni okeru kashika gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Komori, M.; Tsujimura, K. (New ACE., Tsukuba (Japan))

    1993-04-01

    In order to grasp the phenomena actually occurring in the combustion chamber for improving the combustion and for reducing the exhaust gas emission of the diesel engines, the visualization techniques are becoming to be essential and indispensable. The authors have observed the spray and combustion, when proceeding the combustion improvement by the high pressure injection, and then have performed the image processing and simulation calculation based on them. The high pressure injection devices used for the experiment are the intensifier type and accumulator type which can generate the injection pressure more than 200MPa, and both of them are the electronic controlled hydraulic drive type, and are driven separately from the engine. Since it was found that the analysis of high pressure injection by the hologram is limited in the conditions, as for the spray, the spray analysis was performed by the transmitted light attenuation method and laser sheet method. As for the combustion, the engine for observing the combustion was trially made, and then the combustion state was observed by the high speed photograph. Furthermore, the flame temperature analysis by the image processing using the combustion photograph and the analysis of flow and turbulence of the flame were carried out. 9 refs., 16 figs.

  14. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  15. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  16. Investigation into the situation of technology succession; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a fundamental investigation to promote historical succession and creative use of the industrial scientific technology. As for the wind power generation, the large-scaling became centralized wind power plants, and the downsizing became the distribution to remote areas. The solar power generation shifted from the thermal power generation to the light power generation. There is also a method to use solar heat directly. As to power systems and the distribution of electric power, the subjects are a combination of energy source, geographical energy transportation, and heightening of consumption efficiency. It was indicated that the subjects changed with a lapse of time under technical/social/systematical conditions, and under the developable energy amount prescribed by those conditions. Heightening of efficiency, which can be realized even by a paper simulation, was realized partly helped by the developing measuring technology. The environmental problem becomes historically severe as a condition of the technical development. However, aimed at was the process where discharged matters and by-products are effectively used and disused matters are not produced. In the coal-thermal power generation, for example, a load of flue gas purification was reduced by the conversion to LNG. 253 refs., 65 figs., 12 tabs.

  17. Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

  18. Trend of laser cutting technology; Laser setsudan gijutsu no saikin no doko

    Energy Technology Data Exchange (ETDEWEB)

    Murai, T. [Mitsubishi Electric Corp., Tokyo (Japan)

    1997-10-05

    Recent trend of CO2 laser cutting is described. The cutting speed has increased five times in these seven years, and cutting is now performed at 8m/min for a hole that satisfies a circularity of 50{mu}m. In the low-speed domain, again, cutting accuracy is as high as 20{mu}m. In the cutting of thick plates, laser encounters some difficulties, which include the increased thermal load on optical parts and devices in the oscillator, lessened cutting condition tolerance, variation in the accuracy of products, difficult cutting, etc. Discussed in this report are measures for correcting factors affecting product quality with reference taken to a thick soft steel plate. A laser beam emitted by an oscillator is condensed by and projected through a condenser lens, and the condensing capability is affected by various factors, such as the beam mode order, beam diameter, and focal length, etc. What is important is to find out the optimal conditions. The assist gas has to satisfy certain conditions because it assumes an important role in controlling the discharge of molten metal from cut grooves, heat generated by oxidation reaction, and cooling. The properties of the material to be cut also exert some influence. In the case of thick plate cutting, the cutting capability is governed by the geometry to be fabricated. Also employed for the prevention of poor jobs due to improper condition switchover and cutting routes is an optimal cutting condition control technique. 3 refs., 12 figs.

  19. High power YAG laser cutting; Koshutsuryoku YAG laser ni yoru setsudan gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Owaki, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-08-01

    This paper describes features of high power YAG cutting. The optical fiber transmission YAG laser machining system has some advantages in which optical path length compensation unit is not required and measures for low power loss and dust are not required, when compared with the CO2 laser system. Its application to the cutting of stainless steel plates has attracted attention. Cutting tests of SUS304 were conducted using high power YAG laser. Cutting of SUS304 plate with a thickness of 40 mm could be successfully done at the power of 3.5 kW. Cutting tests of SUS304 pipes with a thickness of 8 mm in water under the depth of 20 m were also conducted using air as assist gas at the power of 2.5 kW. Excellent results were obtained without scale deposition. For the tests by the composite beam using 3 kW and 4 kW systems, SUS304 plate with a thickness of 50 mm could be cut at the cutting speed of 0.1 m/min. Laser cutting of pipes from the internal surface was conducted using a newly developed small machining head which can rotate in the peripheral direction. Excellent quality for welding was confirmed. Cutting speed and plate thickness were improved by combining water jet cutter and YAG laser unit. 6 refs., 10 figs.

  20. Leading research on next generation metal production technology; Jisedai kinzoku shigen seisan gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The energy saving environment-friendly technology for low- grade difficult-to-process ores was researched focusing attention on the hydro-metallurgical process of non-ferrous metals. This research aims at development of both effective leaching system of metals, and separation/crystallization system recognizing the property difference between metal ions in solution. The leaching system allows the inexpensive molecular level control of electron transfer, mass transfer of metal ions and stabilization of leached metal ions in a solid/liquid interface. The system thus allows selective leaching of metals from various resources such as difficult- to-leach sulfide minerals to prepare concentrated solutions. The separation system can obtain high-purity solutions including each metal ion by advanced separation/concentration technology from the solutions. The crystallization technology (including electrolysis) is developed for preparing target metal materials by molecular level control of nucleation, particle growth, thin film formation and bulky metal formation processes. Overall energy consumption is reduced to 1/3 of that of the pyro-metallurgical method, aiming at zero emission. 15 refs., 14 figs., 11 tabs.

  1. Techniques for cost-effective electric information sharing; Cost balance wo koryoshita denshi joho kyoyuka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    The key technology that can effectively support the sharing of each information such as documents, data, and know-how was rearranged to clarify how to utilize it for constructing an electronic information sharing system. The key technology that supports the sharing of electronic information was rearranged from the viewpoint of information gathering, information rearrangement, and information utilization. The reduction in cost for information gathering and rearrangement is indispensable to the promotion of much information sharing. However, each automation method presently causes the deterioration in quality of the rearranged information and the increase in cost for information utilization. To realize a practical electronic information sharing system, it is important to combine the key technologies properly so that the total cost balance of information gathering and information utilization is improved. Therefore, the combination of character recognition by OCR and unpreciseness retrieval, and the complementary combination of automatic document sorting, based on multiple incomplete rearrangement systems, and multiple sorting menus were proposed. 23 refs., 5 figs., 2 tabs.

  2. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  3. Bio-desulfurization technology in Japan; Wagakuni ni okeru baio datsuryu gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Maruhashi, K. [Petroleum Energy Center, Tokyo (Japan)

    2000-05-01

    A bio-reaction of microbes (catalytic reaction by an enzyme) is characterized in that the reaction is carried out at a normal temperature and under a normal pressure and has particularly high specificity with respect to substrate (reactant). It is considered that a low loading process of environment harmony type can be constructed by applying the bio-reaction in petroleum refinery process. CO{sub 2} exhaust and energy consumption in the bio-desulfurization (BDS) is estimated to be 70 to 80% lower than those in hydrodesulfurization (HDS). The bio-technologies that can be applied to the petroleum refinery process include, for example, desulfurization, demetallation, dewaxing, denitration, cracking and so on. In this paper, the present state of bio-desulphurization technology is introduced. Particularly, as the research results in Japan, acquirement of mesophile R.erythropolis KA2-5-1 strain, thermophile Paenibacillus sp. A11-2 strain whose optimum temperature is 50 degrees C, BT degradation fungus Rhodococcus sp. T09 and the like are introduced. (NEDO)

  4. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Machine industry technology field (Semiconductor equipment); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) kikai sangyo gijutsu bun'ya (handotai seizo sochi bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a semiconductor equipment field, viewing until 5-10 years after. For the future semiconductor industry, the favorable cycling of creation of new demands through performance improvement, and further technology innovation through market expansion is essential absolutely. Since technology development is followed by investment, not only the performance of each equipment but also the higher productivity and cost balance of the whole factory are essential. Self-intelligent function and networking are thus necessary for the equipment. As measures for environment preservation and energy saving, such innovative technologies are required as recycling, reuse, reaction process improvement and alternative technology. Because of diverse final products and a short life time of products, a large-scale collective investment is becoming difficult. A mini-line sequential investment production system according to demand scales is under investigation. Some issues such as micro-technology, realization of 300mm wafer, modularization, CIM, reliability and standardization are also described. (NEDO)

  5. Leading research on artificial techniques controlling cellular function; Saibo zoshoku seigyo gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Advanced research and its applicability were surveyed to apply the advanced functional cells to industry. The basic target was set to develop, produce, control and utilize the functional cells, such as intelligent materials and self-regulation bioreactors. The regulation factors regarding apotosis, which is a process of cell suicide programmed within the cell itself of multicellular organisms, cell cycle and aging/ageless were investigated. Furthermore, the function of regulatory factors was investigated at the protein level. Injection of factors regulating cellular function and tissue engineering required for the regulation of cell proliferation were investigated. Tissue engineering is considered to be the intracellular regulation by gene transduction and the extracellular regulation by culture methods, such as coculture. Analysis methods for cell proliferation and function of living cells were investigated using the probes recognizing molecular structure. Novel biomaterials, artificial organ systems, cellular therapy and useful materials were investigated for utilizing the regulation techniques of cell proliferation. 425 refs., 85 figs., 9 tabs.

  6. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  7. Simulation technique on combustion of solid propellant; Kotai suishin`yaku nensho no simyureshon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Iida, Akihide.; Bazaki, Hakobu.; Douke, Kiyotaka. [Asahi Chemical Industry Corp., Tokyo (Japan). Oita Plant

    1999-04-30

    The burning area of propellant grain is one of the most important parameter in conducting of design on solid rocket performance. However, it has been difficult to calculate the burning area of propellant grain with precise and speed by geometrical way since most of propellant configuration have been adopted as complicated. In the present study, the simulation system was developed and produced, which was adapted `particle chasing method` to and made ot compute the burning area transition. Moreover, the reliability on computation by the system was check up on. It was found that the discrepancy of calculation between by the geometrical way and by the system was less than 1%. (author)

  8. Application of FEM flow analysis to environmental engineering. FEM ryutai kaiseki no kankyo gijutsu eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, M; Ando, K; Shimada, S; Umetani, H [Toyota Motor Corp., Aichi (Japan)

    1990-04-25

    In order to apply FEM (finite element method) flow analysis to environmental engineering, the two-dimensional analysis system was developed, and applied to the design of plant ventilation and improvement of an enviromental control equipment. Furthermore, the three-dimensional analysis system was developed to extend its application. Since in a large scale model, no enhancement of a processing capacity was expected even by a supercomputer because of longer I/O times between internal and external memories caused by a small internal memory space, the parallel processing system with multiple external memories was introduced to analyze such models. To achieve more efficient processing, multiple series of renumbering codes were also prepared to optimize the processing order of solvers, elements and nodes. As examples, the improvement of a thermal oxidizer and the ventilation design for a forging plant, and as an example of a three-dimensional large scale model, the flow analysis around a plant were presented. 8 refs., 17 figs., 1 tab.

  9. Leading research on cell proliferation regulation technology; Saibo zoshoku seigyo gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing intelligent material, animal test alternative model, bio-cell analysis equipment, self-controlling bio-reactor and medical material, development of functional cells was studied by cell proliferation regulation technology. In fiscal 1996, the expression analysis and separation technology of specific gene for cell proliferation, and the intracellular regulation technology were surveyed from the viewpoint of intracellular regulation. The cell proliferation regulation technology by specific regulating material of cells, extracellular matrix, coculture system and embryonic cell was surveyed from the viewpoint of extracellular regulation. In addition, based on these survey results, new cell culture/analysis technology, new bio-material, artificial organ system, energy saving bio-reactor, environment purification microorganism, and animal test alternative model were surveyed as applications to industrial basic technologies from a long-term viewpoint. The approach to cell proliferation regulation requires preparation of a concrete proliferation regulation technology system of cells, and concrete application targets. 268 refs., 43 figs., 4 tabs.

  10. Generic supercritical water technology; Generic technology to shite no chorinkaisui riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Arai, K; Ajiri, M; Inomata, H; Smith, R; Hakuta, Y [Tohoku University, Sendai (Japan). Faculty of Engineering; Yokoyama, C [Tohoku University, Sendai (Japan). The Institute forChemical Reaction Science; Chin, L [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    This paper describes the measurement and analysis for clarifying solution structure of supercritical water and exhibition mechanism of solvent functions. It also describes the development of new processes using supercritical water as reaction solvent. The PVT measurements were conducted in the supercritical region using pure water and NaCl aqueous solution, to confirm the reduction of molar volume of the electrolyte solution. The hydration structure was examined in the supercritical aqueous solution by the molecular dynamic simulation. As a result, presence of hydrogen bond structure, where the contribution of two branching hydrogen bond can not be ignored, was suggested under the supercritical condition. Characteristics of supercritical aqueous solutions are analyzed through in-situ Raman and scattered X-ray spectral measurements. Moreover, this paper introduces developments of some processes in the supercritical water, such as decomposition of wasted polymers, recovery of chemical materials, reforming of heavy hydrocarbons by contact hydrogenation, and synthesis of fine powders of metal oxide by reaction crystallization.

  11. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  12. Denchuken review. Prospecting and visualization technology; Denchuken review. Chika no tansa kashika gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-30

    This paper introduces the prospecting and visualization technology cultivated in Denchuken (Central Research Institute of Electric Power Industry). The fluctuations in underground gas, underground water, gravity, terrestrial magnetism, and terrestrial current are information from the earth. The change in underground structure, underground water movement, and underground properties can be grasped using this information. With the progress of electronic engineering, a geophysical exploration method has been rapidly developed in recent years. This method is the most advanced technology in many ground examination methods. In the Denchuken, the following methods have been put to practical use between the shallow section of several meters under ground and the deep section of several kilometers. An underground radar method, seismic prospecting method, electrical prospecting method, CSAMT method that estimates the position of geothermal sources or faults by electromagnetic waves, TDEM method, and AE method that destroys the rock at the depth of the ground and detects by slight sound. Moreover, a geotomography method that can visualize the ground depth in precision using a bore hole by nondestruction executes the tomography based on specific resistance, elastic waves, electromagnetic waves, and percolation. 127 refs., 94 figs., 4 tabs.

  13. Contamination-remedying technology based on biotechnology. ; Bioremediation. Biotechnology wo mochiita osen shufuku gijutsu. ; Bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, M [The Japan Research Institute, Ltd., Osaka (Japan)

    1993-08-01

    Bioremediation technology is outlined. The bioremediation technology is a contamination-remedying technology for the injurious chemical matter discharged in the environment to be made innocuous by utilizing the decomposing ability of microorganisms. That technology is characterized by its energywise economical performance, secondary waste which is not producible and remedy which is possible on site against the contamination. As a treatment system, that technology comprises solid phase bioremediation (The contaminated soil is purified in a soil treatment unit.), slurry phase bioremediation (The contaminated soil is made slurry and decomposed by microorganisms.) and in-situ bioremediation (The treatment is made by injecting nutrients and microorganisms underground.). As for how to use the microorganisms, there are two methods: One in which living groups of microorganisms are activated and the other in which microorganisms are artificially cultivated. As contaminants in the US, listed are organic solvent, wood preservative, high-molecular aromatic halide, agricultural chemical, military waste, heavy metal waste and radioactive waste. 11 refs., 5 figs., 1 tab.

  14. NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

  15. History of technological activities of Japanese industry; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    History of technological activities of Japanese industry has been recorded, preserved, compiled and systematized. The purpose is to make international contribution by transmitting Japanese experience and knowledge to the world, and to bring up the human resource for researches by teaching the history of passion and efforts of the predecessors and by arousing interests and creative volitions of science and technology of young persons. However, memorial matters, data and witnesses relating to the history of industrial science and technology are rapidly being lost day by day. When leaving as it is, succession of the history to next generation becomes hard. Under such a situation, basic survey has been conducted to succeed the history of industrial science and technology and promote the creative utilization of them. This is in the third stage of the survey. This report contains the development of new cold rolled steel sheet for cars, plant engineering technology in Mitsubishi Heavy Industries, electronics, electric power distribution technology in Kansai Electric Power Co., Inc., development of the PAN carbon fibers, four cycle and low speed marine diesel engines, production of electrolytic copper foil, development of jet engines, camera makers, and production of office machinery. 86 refs., 12 figs., 9 tabs.

  16. Instrumentation technology to be used for sense alternative. Kankaku daiko wo mezasu keisoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tamiya, E. (Japan Advanced Institute of Science Technology, Hokuriku, Ishikawa (Japan))

    1994-07-05

    Recently, artificial taste sensors or smell sensors that simulate the biological recognition mechanism were developed. This paper describes a smell sensor using natural and artificial fats as the molecule recognizing material and the crystal oscillator or SAW (Surface Acoustic Wave) device as the transducer. The paper also describes the results of the experiments made on the sensor. This sensor consists of 20 LB (Languivir-Blodgett) layers of several types of natural fats on the SAW device. Natural fats on the surface of the crystal oscillator were coated and the response to smelling substances was checked. The result indicates that the response is almost proportional to concentration, and that alcoholic smells can be recognized. To check receiving signal from the sensor system related to absorption and the absorption speed and converting it into higher order information, experiments were conducted to convert data into characters through the neutral network. Though there are still issues of practical use, it was verified that these techniques are effective. 9 refs., 6 figs., 1 tab.

  17. CIM overview. (2). ; Architecture, infrastructure, information technology. CIM soron. (2). ; Architecture, infra, joho riyo shien gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Seryo, K [IBM Japan Ltd., Tokyo (Japan)

    1991-12-10

    The materialization of computer integrated manufacturing (CIM) requires an establishment of its systematizing system, i.e., architecturer and planning of the infrastructure to support it and basic engineering to support the informational utilization. The CIM architecture is classified into management and system structure, strategic planning method, System development introduction method, etc. The infrastructure aims at epoch-makingly heightening the productivity and speed by integrating the production planning, engineering design, accounting, sales, general business and affairs, production engineering, production activities, and activities of suppliers and clients. The informational utilization support engineering comprises the management support tool, decision making support tool, application development tool, etc. What is important is to establish a system of systematizing engineering in order not to be behind the strategic activation era of information to come. 17 refs., 4 figs., 1 tab.

  18. New technique of railway bridges in Hokuriku Shinkansen; Hokuriku Shinkansen tetsudokyo no gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyabayashi, H. [Japan Railway Construction Public Corp., Tokyo (Japan)

    1996-09-01

    This paper presents new technologies of the railway bridges in Hokuriku Shinkansen. Hokuriku Shinkansen of 117km between Takasaki and Nagano is a part of Shinkansen connecting Tokyo with Nagano by nearly 1.5 hours. Its construction is in promotion under severe financial condition, and cost reduction is an essential target. Among the concrete bridges in this section, Kirizumigawa bridge, a prestressed concrete strutted 3-span continuous beam bridge, adopted a lowering erection method for its slant pier. In this method featured by high safety and profitability, the rib component of a concrete arch bridge is vertically erected on a arch support, and installed by swinging it toward the central span. In addition, a cantilever method was adopted to keep the scenery of a national park. Daini Chikumagawa bridge with the longest span of 133.9m among concrete railway bridges is the first cable-stayed prestressed concrete bridge in Shinkansen. Yashiro Minami and Kita bridges of 105m and 90m in central span are the extradosed bridges which were adopted as optimum structure for lowering the beam height of meddle-sized railway bridges. 3 refs., 12 figs., 2 tabs.

  19. Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-10-15

    Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

  20. Bridge and steel structures. History and vision on bridge erection; Kyoryo kokozobutsu. Kasetsu gijutsu no shorai

    Energy Technology Data Exchange (ETDEWEB)

    Mukai, S.; Hayashi, T. [Sumitomo Heavy Industries, Ltd., Tokyo (Japan)

    1998-08-20

    This paper describes the progress of bridge erection technology. It introduces the results of cable erection, rotated/extruded erection, and cantilever erection. The cable erection is a multi point suspension erection using cables. For the rotated/extruded erection, the monolithic construction is conducted on a working yard set in a right angle to the construction position, and the horizontal beams of the bridge piers (corbel girders) are constructed by the rotated method using a slewing base incorporated around the bridge piers at one side. For the construction of stiffening girders of Innoshima-ohashi Bridge of Honshu-Shikoku Joint Bridge in 1978, trussed face bar blocks were extruded from the main tower in order using a travel crane. For the suspension bridges and cable stayed bridges, main towers were erected using various types of cranes. The erection of Tamashima-ohashi Bridge with a weight of 500 ton using an offshore floating crane is introduced as a large block method. Analysis methods and measurement techniques at the site are used in order to analyze the shape in each step under the erection and to ensure the accurate final complete shape. Reduction of the construction cost, improvement of erection technology, and technology development for large-scale projects are subjects in the future. 22 refs., 8 figs., 1 tab.

  1. Modern techniques in prestressed concrete cable-stayed bridges. Puresutoresuto concrete shachokyo ni okeru atarashii gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, A. (Kobe Univ. (Japan). Faculty of Engineering)

    1994-03-31

    Because the prestressed concrete (PC) cable-stayed bridges combine the distinctive features such as a rationality of the structure or a structural beauty, it will not stay on a development of the technologies to make them longer and larger, and a rationalization of the execution, an investigation from various aspects such as the scenery design, material selection, pursuit of new structure and so forth will become necessary. In a main meeting, 15 volumes of paper on the most advanced technologies of PC cable-stayed bridges were presented. The presentations from Japan were 11 volumes, and occupied about 70%, and therefore a high interest to the PC cable-stayed bridges in Japan was inferred. In the presentation from Japan, there were many relevancies of the important study themes which would become a foundation for a development of PC cable-stayed bridges in the future, like ones that an improvement effect of dynamic behavior such as the aseismatic property, wind endurance and so forth was made as an objective, ones that a safety evaluation at an ultimate state as the oblique member anchoring part, main tower or entire structure was related, ones that a construction of the various control systems when the cable-stayed bridges were executed was concerned and so forth. 23 figs., 1 tab.

  2. Recent design methods for prestressed concrete cable stayed bridge; PC shachokyo no sekkei gijutsu no genjo

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, K. [Kajima Corp., Tokyo (Japan)

    1995-02-01

    The number of constructed prestressed concrete cable stayed bridges reached nearly 100 in Japan, and the technique has greatly developed. In this article, the current status of design techniques for prestressed concrete cable stayed bridges were introduced along with the examples of constructed bridges for the analysis method and the design method for each structure part while introducing the current examples of constructed bridges. Also, this kind of extra-dosed prestressed concrete bridge and prestressed concrete bridge with prestressed concrete stays were reported. Standards have been prepared including a chapter for the prestressed concrete cable stayed bridges in the Road Bridge Guideline document in February 1990. Load to be noticed as the characteristics peculiar to the prestressed concrete cable stayed bridges includes the shock due to live load, temperature change, and execution error of a tower. For example, 1/1000 of the total tower height is generally considered as the execution error of the tower. A diagonal member is manufactured at factories and in fields and has both advantages and disadvantages. The linear analysis of plane framework is general. Damping of and earthquakeproof designs against the wind and earthquake of the diagonal member were also provided. 11 refs., 17 figs., 2 tabs.

  3. Survey on the succession situation of technologies; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The basic survey was carried out to promote the succession and creative use of the previous industrial science and technology. The following 5 themes were summarized in fiscal 1993. On `Fuel technology policy and technological development,` Navy Fuel Depot, Chemical Research Institute at University of Kyoto, Central Laboratory of South Manchuria Railway Co., and Fuel Research Laboratory of the Ministry of Agriculture and Commerce played important roles, and the 1000atm continuous hydrogenation system was completed in 1941. On `Technology of long-distance power transmission,` high-voltage insulation technology finally reached an international level after World War II. On `Unification of frequency and electrical technology,` the two-frequency system for eastern and western areas was established before World War II, and construction of Sakuma Frequency Conversion Station allowed power interchange between two areas. On `Organization of national research laboratories,` the Agency of Industrial Science and Technology distinguished the roles of new and existing laboratories. On `Wind power technology in Europe and America,` comparison between American and Danish approaches is the most important issue today. 146 refs., 20 figs., 13 tabs.

  4. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  5. Gas removal technique to maintain global environment. Chikyu kankyo hozen no tame no bojo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1992-10-12

    This paper describes the removal technique of gases such as CO2, SO2 and NOx which have the deep relation to the maintenance of global environment. This paper describes partially r SO2 and NOx which are the primary cause of acid rain. As for the removal of CO2 generated from fixed sources (thermal power stations and others), the separation technique and isolation-fixation technique have been researched on and developed. Of the separation method, the effect of the chemical absorption method and the adsorption method is proved with the preceding experiments. The isolation method is differently researched on as to store under deep sea or ground but may be urgent and temporary. The fixation of CO2 is a serious global problem which relates to the afforestation and forests. The fixation which uses coral reefs in ocean as the absorption source has a potential. As for the processing of substances causing acid rain, the desulfurization from petroleum and the flue gas desulfurization have the excellent results. The improvement of combustion method or the flue gas denitrification at the fixed sources are used to remove NOx. The removal of NOx from all diesel cars is difficult compared with the exhaust gas cleaning of gasoline cars and is not commercialized. 11 refs., 1 fig., 2 tabs.

  6. Fiscal 1999 research report on long-term energy technology strategy. Pt. 2. Basic research on industrial technology strategy (Individual technology strategy.) Material technology field (Fine ceramics); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 2. Sangyo gijutsu senryaku sakutei kiban chosa (bun'ya betsu gijutsu senryaku) zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the basic research result on industrial technology strategy for a glass field. Japan is facing such various economic problems as attack by developing countries, collapse of economic babble and yen's appreciation, and environment problems over a period of several years, and a glass industry is also under the influence of such problems. For continuous development of Japan and improvement of the international competitiveness of Japan, development of a glass industry is essential. Both co- possession of technical issues by cooperation of the members, and breakdown of conventional structures of the industry are necessary. Clarification of technical issues, and cooperation of industry, academia and government is essential. The current state, promise and issues of domestic and overseas glass technology and its R and D are described. The joint target of an industrial strategy for researchers and engineers of every sector, and the approach to such target are showed from the viewpoint of the issues for Japan and preparation of common basic technology. The role of each sector for environment preparation and policy is described to achieve the target. (NEDO)

  7. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Part 1. Technology strategy by field - material technology field (fine ceramics technology field); 1999 nendo choki energy gijutsu senryaku ni kansuru chosa. 1. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the fine ceramics technology field relating to the FY 1999 long-term energy technology strategy. The fine ceramics industry is a new industry for which the future development is expected. It has far-reaching effects on other industries. Japan has the advantage over other countries. As subjects to remarkably develop the industry, needed are the long-term basic preparation which promotes technology innovation such as the promotion of the fundamental/creative R and D, construction of an industry/university liaison system, and arrangement of the intellectual base. Preparation of the competitive environment and promotion of policies paying attention to the market are needed which make the development under the private control by creative study/corporate activities possible. Also important are the demonstration of leadership and secure international competitive force in the light of Japan's international position. For the private-control development, the role and course of various groups should be made clear from a long-term aspect. It is desirable that university/government will newly develop innovative technology, and industry will make the present technology force more developmental and competitive. Support from the nation is requested for researches large in scale. (NEDO)

  8. Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

  9. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Aerospace technology field - Airplane technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (koku uchu gijutsu bun'ya (kokuki gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as the analysis of the present state of technical competitive force and the forecast in the airplane technology field. In future airplane industry, to meet the requests/restrictions from the society in the international airplane industry in the recent years, it is predicted that technology innovation will advance centering on the following four fields: next generation airplane technology to enable the innovative cost reduction in development/production, technology to realize the substantial reduction in flight cost of airline, technology to enhance reliability for the next generation flight which meets the multi-frequency flight/increasing demand for small plane, and airplane frontier technology. Moreover, regulations especially on noise, CO2 reduction and NOx reduction are becoming very strict internationally because of the increasing concern about global environmental problems. It is urgently needed to establish technology to cope with these trends. As the comprehensive strategy, the following are considered: development of airframe under the leadership of Japan and securing of the demand, efficient arrangement and operation of large-scale experimental facilities, IT adoption to the airplane industry, organic cooperation by industry/university/government, etc. (NEDO)

  10. Analysis and evaluation of data to accompany the development of geothermal water use power plant, etc. Analysis and evaluation of polymeric materials exposed to geothermal heat at depths; Nessui riyo hatsuden plant nado kaiahtsu ni tomonau data no kaiseki hyoka. Shinbu chinetsuyo kobunshi zairyo no kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmochi, K.; Takahashi, J.; Takayanagi, H.; Tsuda, H.; Nagai, H.; Takeuchi, K. [Agency of Industrial Science and Technology, Tokyo (Japan); Nagasawa, C. [Kumamoto Prefectural Industrial Technology Center, Kumamoto (Japan); Hamada, T. [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1998-11-20

    Remaining life assessment technologies for polymeric materials for geothermal power generation and methods for improving their heat resistance are reviewed, and concepts of scale-free technologies for FRP (fiber-reinforced plastic)-sandwiched pipelines for hot water transportation are described. Materials based on PTFE (polytetrafluoroethylene) and NBR (acrylonitrile-butadiene rubber) are chosen for use as DHM (down-hole motor) sealing material and for application to the stator. With PTFE as the matrix, four candidates are prepared, which are additive-free PTFE, and GF/PTFE, GF/CF/PTFE, CF/PTFE, each containing 20w% GF (glass fiber) and/or 20w% CF (carbon fiber). With NBR serving as the matrix, two candidates are prepared, which are NBR-A containing 20w% aramid fiber and NBR-W which is a vulcanized NBR-A. External force, heat, light, and mud are named as the degradation factors, and each factor and some combinations of external force, heat, and light are repeatedly imposed on the materials. During the effort to develop an apparatus for simulating geothermal circumstances in which the factors will affect the materials in complicated ways, a life assessment technique is developed for such polymeric materials. A technology is developed for providing polymeric rubber elastomer with a heat resistant feature. A study is made to replace transportation pipelines for injection wells with FRP sandwiched pipelines. (NEDO)

  11. Analysis and evaluation for practical application of photovoltaic power generation system. Research and development of elemental technologies for thin-type solar cells; Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usugata takessho taiyo denchi jitsuyoka no tame no kaiseki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, T; Shimokawa, R; Yui, N; Takato, H; Takahashi, T; Ishii, K; Suzuki, E; Nagai, K; Kawanami, H; Tanimoto, J; Sakuta, H; Iwata, Y; Saito, N; Koyama, K; Sawada, S [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for thin substrate polycrystalline solar cells. In order to analyze the structures of the grain boundaries in and interfaces with the cell substrate, and their effects on electrical activity, the photoluminescence (PL) measurement which enables spectroscopic analysis is applied to electromagnetically cast Si crystals. There are good correlations among PL luminous intensity, MBIC output and dislocation density for the grain boundary which contains many strains and serves as the dislocation source, because carriers in such a grain boundary easily disappear to reduce its luminous intensity at the band ends. Concrete scenarios for realizing thin-film silicon solar cells of high efficiency are presented, based on the analysis of the light-contained thin-film silicon solar cells of high output current, made in the previous year on a trial basis. An alumina substrate of high reflectivity is produced by the experiments of combining various devices. It is expected to realize high output current for the thin-film solar cells. 3 figs.

  12. Performance evaluation of solar heating system with thermal core type soil heat storage. Part 5. Performance prediction and evaluation of the system considered of the weather condition; Taiyonetsu riyo netsu kakushiki dojo chikunetsu system no seino hyoka. 5. Kisho joken wo koryoshita system no seino yosoku to hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, N [Nishimatsu Construction Co. Ltd., Tokyo (Japan); Nakajima, Y [Kogakuin University, Tokyo (Japan)

    1997-11-25

    The paper studied a solar heating system with thermal core type soil heat storage (combining a thermal core composing of a water tank and an underground pebble tank and the soil around the heat storage tank and also using solar energy). Solar energy is stored by temperature level in the high temperature water tank, the low temperature pebble heat storage tank and the soil around the heat storage tank. Heat is recovered according to temperature as direct ventilation space heating (utilization of pebble tank air), floor heating (utilization of hot water of the heat storage water tank) and heat pump heat source (utilization of pebble tank air). A study was made of performance and regional effectiveness of the system under different weather conditions. A study was also made of effects of the water tank for short term heat storage by changing the water volume. Using the same structure, etc. for the system, the system was evaluated using weather data of Sapporo, Tokyo and Kagoshima. In terms of efficiency of the system, the system structure was found to be most suitable for weather conditions in Tokyo. However, the air heat source heat pump which cannot be usually used in the cold area has come to be used. Such effect except efficiency is also considered, and the amount of performance to be targeted in each region changes. 2 refs., 14 figs., 1 tab.

  13. Quantitative evaluation of ground improvement by chemical grouting using electrical resistivity. Part 3. Applicability of evaluation of improved region by resistivity tomography; Denki hiteiko ni yoru yakueki chunyu kairyo koka no teiryoteki hyoka hoho. 3. Hiteiko tomography wo riyoshita jiban kairyo han`i hyoka hoho no tekiyosei

    Energy Technology Data Exchange (ETDEWEB)

    Komine, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-02-01

    This paper describes a method for evaluating grouting that is a means for improving the ground for excavation for building underground structures in urban areas. This is an effort for improving reliability, and evaluates the rate of filling of the water glass base chemical liquid injected for improving the ground utilizing the fact that this liquid is higher in conductivity than the soil or ground water. An experiment was conducted using a model ground so as to define the limit of applicability of this resistivity tomography by studying electrode arrangements and difference in resistivity between the grouted liquid and ground water. It was then found that the liquid-injected region is evaluated more accurately when the measuring electrodes are installed nearer to the region, that evaluation is satisfactorily accomplished when the region spans not less than 75% of the distance between the electrodes, that higher accuracy is expected when the difference in resistivity is greater between the grouted liquid and ground water, that evaluation is satisfactorily accomplished when the resistivity of the grouted liquid is not more than 10% of that of ground water, and that any grouting liquid usable for ground improvement in civil engineering in urban areas can be applied to any other grounds except where there is influence of seawater. 31 refs., 55 figs., 8 tabs.

  14. Report on results concerning development of supermetal technology (FY2000). Innovative manufacturing technology for iron-based mesoscopic structured material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Tetsu kei mesoscopic soshiki seigyo zairyo sosei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing innovative manufacturing technology for microstructure steel having a crystal grain size of about 1 {mu}m or less and a dimensional thickness of 1 mm or more by homogeneous multi-phase structure steel making, R and D was conducted, with fiscal 2000 results compiled. This year, R and D, using a multi-functional integrated test rolling mill, resulted in obtaining ultra-fine grained steel, a steel plate of 5 mm in thickness and 100 mm in width with grains of 1 {mu}m or less homogeneously in the thickness direction. In the investigation on the characterization by the steel plate sample thus obtained and on the method for preventing degradation in elongation, it was proved that an ultra-refined microstructure containing martensite or austenite as the secondary phase has a suppressing effect on the degradation in elongation. Further, examination was made on the widening of a process window for the practicability in the future and on the optimization of large strain deformation conditions. In the method of analyzing and evaluating ultra-refined microstructures, an analysis technology such as an in-lens SEM was proved to be extremely effective on the analysis of microstructures of supermetals created by large strain deformation as well as on the observation of microstructures of a submicron level. (NEDO)

  15. Hydrogen energy technology development conference. From production of hydrogen to application of utilization technologies and metal hydrides, and examples; Suiso energy gijutsu kaihatsu kaigi. Suiso no seizo kara riyo gijutsu kinzoku suisokabutsu no oyo to jirei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-02-14

    The hydrogen energy technology development conference was held on February 14 to 17, 1984 in Tokyo. For hydrogen energy systems and production of hydrogen from water, 6 papers were presented for, e.g., the future of hydrogen energy, current state and future of hydrogen production processes, and current state of thermochemical hydrogen technology development. For hydrogen production, 6 papers were presented for, e.g., production of hydrogen from steel mill gas, coal and methanol. For metal hydrides and their applications, 6 papers were presented for, e.g., current state of development of hydrogen-occluding alloy materials, analysis of heat transfer in metal hydride layers modified with an organic compound and its simulation, and development of a large-size hydrogen storage system for industrial purposes. For hydrogen utilization technologies, 8 papers were presented for, e.g., combustion technologies, engines incorporating metal hydrides, safety of metal hydrides, hydrogen embrittlement of system materials, development trends of phosphate type fuel cells, and alkali and other low-temperature type fuel cells. (NEDO)

  16. Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

  17. FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

  18. Fiscal 1998 research report. Research cooperation on car energy and environmental technology based on ITS technology in China; 1998 nendo seika hokokusho. Chugoku ni okeru ITS gijutsu wo mochiita jidosha energy kankyo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims at preparation of the car energy/environmental vision based on ITS (intelligent transport system) technology in China, enhancement of the transport planning ability of Qinghua University, and promotion of effective energy use in China. The following activities were carried out concretely: Survey on the actual traffic situation by Qinghua University, analysis of environment deterioration factors based on the survey result, estimation of a traffic environment improvement effect, study on traffic flow simulation technique based on traffic engineering, and study on traffic planning technique. As the diffusion strategy of ITS along Chinese circumstances, standardization and improvement of a multi- modal traffic system, navigation and its application system, and ETC (electronic toll collection) system are promising. Expectation for Japan and Japanese roles are as follows: Improvement of signal control, provision of information systems such as navigation, discussion on ITS technology such as ETC with Chinese specialists, and feasibility study on introduction of ITS technology for every Chinese district. (NEDO)

  19. Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

  20. Achievement report for fiscal 1976 on Sunshine Program. Research on hydrogen production technology (Research on hydrogen production technology using thermochemical method); 1976 nendo suiso no seizo gijutsu no kenkyu seika hokokusho. Netsukagakuho ni yoru suiso seizo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report covers part of the efforts to develop new hydrogen production technologies. Out of many processes involving Cu-halogen and alkali carbonate-iodine systems proposed as novel thermochemical processes, after they are compared with each other, a process of a sodium carbonate-iodine system with nickel in between is chosen. The chosen process is deemed to be the most excellent among the processes disclosed up to fiscal 1975. A feasibility study is conducted for the chosen process from the viewpoint of reaction rate, separation of reactive substances from each other, method for reaction manipulation, materials for device constitution, and thermal efficiency. As for the measurement of reaction rate for each unit reaction, basic reaction data are determined centering about the nickel iodide decomposition reaction and the sodium iodide carbonation reaction, and then reaction conditions which are roughly satisfying are obtained. A larger reaction unit is built in which the amounts of substances that come into reaction are approximately 10 times larger than those in the ones used in basic experiments. The progress of reactions is observed in the reaction unit, with the size enlarged in preparation for future construction of still larger reaction units. Methods for selectively isolating hydrogen out of gases ensuing from the decomposition are evaluated from the viewpoint of energy efficiency. In the selection of a reaction manipulation method, a single unit reaction process is advocated, and its thermal efficiency is estimated. (NEDO)

  1. FY 2001 report on the results of the follow-up study of development of the highly effective waste power generation; 2001 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of safe operation of the highly effective waste power generation pilot plant, confirmation of the performance of corrosion resistant super heater materials under the high temperature corrosion environment, collection of the data on environmental load characteristics in waste incineration, etc., the follow-up study was made. The results were as follows: The pilot plant was able to generate high temperature/high pressure vapor stably for approximately 13,500 hours in FY 2000 and FY 2001 and for approximately 27,800 hours in 4 years since the start of the demonstrative test. The planned performance of plant facilities was fully satisfied, and the performance of environmental load reduction was fully satisfied in standard values of soot/dust, SOx, NOx, hydrogen chloride and dioxins in exhaust gas. Concerning the super heater use developmental material, its durability of 5 years or more was confirmed. It was forecast that by using this, the heightening of temperature/pressure of boiler to 500 degrees C and 100 atmospheric pressure was achieved. Further, the useful information/knowledge on plant design were obtained such as the corrosion prevention technology for waste plant and the forecast of corrosion life of materials. (NEDO)

  2. Report on development of super metal technology and on result of innovative technologies for producing material for controlling iron-based mesoscopic structure; 1999 nendo super metal no gijutsu kaihatsu tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D was conducted for the purpose of 'establishing innovative technologies for producing microstructure steel having a grain size of approximately 1 {mu}m or less and a thickness of 1 mm through the formation of uniform multi-phase structure steel', with the results for fiscal 1999 summarized. In the subject year, a multi-functional integrated test rolling mill was introduced, with possibility validated for grain ultra-refinement by three types of large strain deformation, and with the effect of deforming conditions confirmed. As for the theoretical understanding of the mechanism of grain ultra-refinement and the establishment of its guiding principle, a progress was made in clarifying the ultra-refinement mechanism particularly by the strain-induced ultra-low-temperature diffusional transformation, revealing for example that micro-bands formed in deformed austenitic substructures provided the nucleation sites for ultra-fine ferrite. In the evaluation of properties on medium size samples prepared by the multi-functional integrated test rolling mill, remarkable improvement was confirmed in yield strength and tensile strength in martensitic steel or tempered martensitic steel as well as in ferritic steel. (NEDO)

  3. FY 1998 report on the results of the research and development of fundamental technologies for superconductor applications; 1998 nendo chodendo oyo kiban gijutsu kenkyukaihatsu seika hokokusho. Chodendo oyo kiban gijutsu keknyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    As to the research on the superconductor manifestation mechanism, Y123 monocrystal which was partially replaced with Zn and Ni was manufactured, and it was made clear that the addition of these impurities greatly change anisotropy of superconductors. It was made clear that instability of lattice and magnetism is included in high temperature superconductor. Also made clear was an important role in the Nb/Ba replacement in existence of magnetic flux melting phase transfer and the magnetic field induced pinning effect. The manufacture of Y123 bicrystal membrane was successful by the liquid phase epitaxy method. The manufacture of non-copper base K-Bi-O new superconductor was successful by the ultra-high pressure synthesis method. The stabilized process was established for large size crystals of 15-20mm square in Y base and of 20-25mm square in Nd base. Also successful was the growth by LPE method of crystal with thick membrane of 20mm x 20mm x 10{mu}m on the MgO monocrystal substrate. The non-bicrystalization of Y base Nd base monocrystal was successful, and the peak phenomenon control in Jc-H was found out. By neutron irradiation, the acquisition magnetic field of 3.7T at 77K was achieved using bulk Y base 123 material with diameter of 3cm. And, the critical current density of 60,000 A/cm{sup 2} was achieved at 77K and 3T. (NEDO)

  4. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

  5. Fiscal 2000 achievement report on development of high-efficiency high-reliability welding technology through improvement on welding techniques; 2000 nendo yosetsu gijutsu no kodoka ni yoru kokoritsu koshinraisei yosetsu gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are made to develop a welding design support system capable of increasing reliability and enhancing welding efficiency. Activities are conducted in the six fields of (1) the development of welding process simulation models, (2) development of welded section structure simulation models, (3) development of simulation models for predicting welding caused deformation, (4) integration of the models, (5) analysis of the welding phenomenon, and (6) the elucidation of the defect generation mechanism. In field (1), efforts are made to develop an arc plasma model, a molten pool convective heat transportation model, and a welding process model. In the effort to develop an arc plasma model, studies are made about a stationary axisymmetric arc in its steady state and about a constitutive equation and computation algorithm for developing a model in which a tungsten electrode (cathode) and an arc plasma welding pool (anode) are integrated. Furthermore, the simulation outcomes are experimentally verified. Satisfactory models are obtained as far as qualitative properties are concerned. (NEDO)

  6. Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

  7. High performance milling techniques on molding dies. Development of new roughing techniques for large molding die; Plastic kanagata seisaku ni okeru kokoritsu kako gijutsu. Ogata plastic yo kanagata no keijo arakako gijutsu no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, H; Kohama, S; Yamakawa, M [Mazda Motor Corp., Hiroshima (Japan); Egusa, H [Mazda Tooling and Engineering Co. Inc., Hiroshima (Japan)

    1997-10-01

    It needs long time to carve a molding die of bumper, which has a large and deep cavity. To shorten the milling time, we must make the machining more performable and accurate, and develop the new technology of CAM. In the milling sequence, Primary Roughing, which cut out 90% of the stock, should be more and more performable. So we established Tilt-Plunging and Curve-Fit Spiral Cutting techniques. These techniques will reduce lateral force to the tool, and make remains more small. With the techniques, we reduced both machining and NCdata preparing time to one half. 1 ref., 14 figs.

  8. Fiscal 1999 research report. Japan-U.S. comparative research on energy technology transfer and innovative industry support; 1999 nendo energy gijutsu wo chushinto shita gijutsu iten oyobi shinki sangyo ikusei no Nichibei hikaku ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Japan-U.S. comparative research was made on technology transfer and innovative industry support. The U.S. industry is greatly benefited by universities, which is consequently strengthening the international competitiveness of the U.S. economy. However, the partnerships between private firms and universities have no fixed pattern, and keep changing dynamically. Business incubators increased to 627 rapidly, and mainly supported by municipal governments and universities. The U.S. has a well-established mechanism of technology transfer, and has succeeded in many cases. Not only universities but also national laboratories commit to technology transfer to venture businesses, and after starting businesses, entrepreneurs can use various hedging systems which are expected to play a role promoting the future technology innovation. The U.S. also has many advanced areas for sustainable technology innovation, like Silicon Valley, and these areas contain many supporting bodies to help new businesses. The activity of these bodies is very suggestive to Japanese local platforms promoting technology innovation and new local industry creation. Study was also made on the possibility of technology exchanges with overseas advanced areas. (NEDO)

  9. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  10. NEDO Forum 2001. Session on industrial technology development (Future of thing making and manufacturing/processing technologies); NEDO Forum 2001. Sangyo gijutsu kaihatsu session (monozukuri seisan kako gijutsu no mirai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. In a lecture entitled 'History of thing making,' the roles played by the now-defunct National Testing Laboratory and Industrial Test and Research Center were described and strategy for future development was predicted. In a lecture entitled 'Thing making and international apprentices competition,' apprenticeship training in practice at Denso Systems Corporation was presented. In a lecture entitled 'Key technology in thing making: outlook of metal mold industry,' shift in Japanese manufacturers' paradigm and change in metal mold marketing were explained, and the importance of reaching for the first position in the world in some specific fields or of expanding the scope of work in the entire value chain was stressed. In a lecture entitled 'Digital meister project: Aiming at amalgamation of IT (information technology) and MT (manufacturing technology),' database construction in the manufacture of metal molds, introduction of knowledge management systems, and development of CAD/CAM/CAE (computer-aided design/computer-aided manufacturing/computer-aided engineering) were discussed. (NEDO)

  11. Report on the survey in fiscal 1998. Systematic arrangement of environment technologies. 5 (Application of advanced technologies to environmental measures); 1998 nendo chosa hokokusho. Kankyo gijutsu ni kansuru taikeiteki seiri. 5 (sentan gijutsu no kankyo taisaku eno oyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Global environment handling technologies were investigated and put into order. Universities often make research and development on themes that can be handled at laboratory levels or by simulations. Development at a practical application level is few. Technological seeds may include manufacture of hydrogen by water and steam decomposition using solar energy, and new synthesizing reactions utilizing solar energy. Included may also be urban type wind power generation, superconductive energy storage systems, biomass utilization, and natural energy utilization. Furthermore, CO2 recovery and utilization by liquefaction, alkaline metal heat power generation, and pulse power technologies can also be found. Studies on applying advanced technologies to environmental measures include composite materials, membrane separation, photo-catalysts, optical elements, porous bodies, functional polymers, bio-reactors, electron beams, and aeration. Private corporations are working noticeably on prevention of fluorocarbon and dioxin emission, PCB treatment and waste water treatment technologies, catalyst application technologies, recycling technologies, and incineration ash treatment and utilization technologies. (NEDO)

  12. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of HFC-23 destruction technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. HFC-23 hakai gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    HFC-23 is produced as a by-product during HCFC-22 manufacturing (produced at by-production rate of about 2%, whereas the reaction control has limitation in reducing the production). This is one of the substances subjected to the greenhouse effect gas reduction in the climate change framework treaty. This paper describes the achievements in 1998 on developing the HFC-23 destruction technology. High-temperature pyrolysis decomposes the substance into HF and CO2, which are given absorption treatment by water and alkali to make them harmless, and are recovered finally as calcium fluoride. An equipment having the treatment capability of 195 kg/h was constructed. Design was made on a facility capable of treating fluorine containing waste water at 3 t/h at maximum. Utilities consumed in a factory (industrial water, acids for neutralization, and alkali) are used effectively to identify the effect of reducing the treatment cost. Discussions were given from the safety aspect on facilities to prevent leakage of fluorine containing waste water being a harmful substance. Fabrication was executed on a full-size treatment testing equipment that can utilize the utilities in the factory effectively, and trial equipment operation was performed to arrange the system prepared toward the future tests and researches. (NEDO)

  13. Fiscal 2000 research report on the research on materialss with functions enhanced by microcapsulation technology; 2000 nendo microcapsul ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research is conducted to create materialss equipped, thanks to microcapsulation, with a noise stopping function, vibration damping function, moisture adjusting function, electromagnetic shielding function, and the like, and usable as structural elements as is, that is, materialss known as 'interactive materialss.' For the development of an interactive materials, it is important to incorporate an element, which interacts with external energy, into the materials. A system using interactive materialss when embodied will ensure a safer and more comfortable daily life space. Taking this into consideration, in this fiscal year, studies are made about the technical representation of problems and troubles that jeopardize the safety and comfort of the daily life space, establishment of standards in this connection, interactive features to be realized using microcapsules, possibility of novel interactive characteristics using the same, techniques for the systematization of microcapsules as industrial materialss, techniques for assessing and analyzing materialss characteristics, simulation or the like of a safe and comfortable space using interactive materials-aided systems, and so forth. (NEDO)

  14. Collection of outlines of Sunshine Program achievement reports for fiscal 1988. Solar energy (Light utilizing technology and heat utilizing technology); 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the experiment, refining, and verification of low-cost silicon; experiment, fabrication, and verification of solar panels; research on the practical application of high-efficiency crystal-based solar cells; research and development of amorphous solar cells; research and development of solar cell evaluation systems; development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and development of photothermal hybrid type photovoltaic power systems. Collected concerning heat-utilizing technologies are the research and development of solar thermal electric power generation systems; research and development of solar air-conditioners and hot water supply systems; and development of practical application technologies for industrial solar systems. Collected also are international cooperative projects on solar energy technologies. (NEDO)

  15. Collection of outlines of Sunshine Program achievement reports for fiscal 1989. Solar energy (Light utilizing technology and heat utilizing technology); 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the research on the practical application of new-type solar cells; research on the practical application of amorphous solar cells; research and development of solar cell evaluation systems; research and development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and research and development of photothermal hybrid photovoltaic power systems. Collected concerning heat application technologies are the research and development of solar thermal energy systems; development of practical application technologies for solar systems for industrial use etc.; and cooperative projects between Japan and Australia etc. on solar energy technologies. (NEDO)

  16. Report on achievement for fiscal 1998. Global environment industry technology development promotion project (the advanced technology survey and research project); 1998 nendo seika hokoiusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (sentan gijutsu chosa kenkyu jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to structure innovative technologies to solve effectively the global environment problems, it is important to incorporate infra-structural technologies that have been achieved by universities and other research institutions. The fiscal 1998 project has commissioned 25 researches found superior from among research plans that have been invited during fiscal 1997. This paper enumerates the main themes including those under continued research. The research themes include: fixation of phosphor by using photo-energy, utilization of nitrogen fixing bacteria in rice plant roots for the purpose of carbon dioxide reduction, new functional solid ultra-strong acids for clean chemical processes, fixation of warming gases by using ultra critical fluid catalytic reactions, photo-catalysts having microporous structure, whose energy structure is controlled, waste water purification by using stimulation sensitive polymers, a practical and small high-speed environment purification system by means of a simple technology to cultivate high concentration bacteria of microorganisms, fundamental analysis of response to specific wavelength light in photosynthesized microorganisms, bio-remediation utilizing symbiotic systems of plants and bacteria, high efficiency catalysts purposed for total decomposition of water, and separation of carbon dioxide in deep sea bottoms by controlling hydrate crystal growth. (NEDO)

  17. Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of high- efficiency production process technology); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on R and D of laser processing technology, in-situ measurement technology, and generation and control technology of photon as laser beam source, for energy saving and efficiency improvement of energy-consumptive production processes such as welding, jointing, surface treatment and fine particle fabrication. The research was carried out by a technical center, 9 companies and a university as contract research. The research themes are as follows: (1) Processing technology: simulation technology for laser welding phenomena, synthesis technology for quantum dot functional structures, and fabrication technology for functional composite materials, (2) In-situ measurement technology: fine particle element and size measurement technology, (3) All- solid state laser technology: efficient rod type LD-pumping laser module, pumping chamber of slab type laser, improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology, fabrication technology for nonlinear crystals, and high-efficiency harmonic generation technology. Comprehensive survey was also made on high- efficiency photon generation technologies. (NEDO)

  18. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  19. Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

  20. FY 1998 achievement report on the photon measuring/processing technology (R and D of the photon measuring/processing technology); 1998 nendo foton keisoku kako gijutsu seika hokokusho. Foton keisoku kako gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In this project, the survey/arrangement were made of the trend of the recent technology such as photon (laser) measuring/processing/generation and a possibility of adopting the photon technology to the field except measuring/processing, to clarify technical subjects for establishing/commercializing the photon technology. Also for the purpose of reducing the energy cost by improving the performance of laser processing device, prolonging the life and reducing the operational cost, the development of the following were carried out: (1) high efficiency laser processing device. (2) high conversion efficiency laser diode. In (1), a laser generating device with Yb:YAG crystal as oscillating medium was trially manufactured, and the power of 35W and optical-optical conversion efficiency of 7.1% were obtained. A comparison was also made between Yb:YAG laser and Nd:YAG laser, and made it clear that as the industrial use high power laser, Nd:YAG laser has the advantage over the other. In (2), the development was made of technology for simultaneous uniform growth of more than one LD crystal wafers with high conversion efficiency and technology for evaluation. Namely, the high uniformity crystal wafer with variations among wafers of {+-}4% was obtained using the introduced high efficiency crystal growth device and high efficiency thin film evaluation device. (NEDO)

  1. FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  2. Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

  3. Report on achievements in research and development in fiscal 1982 commissioned from the Sunshine Project. Development of a pit condition measuring technology (Development of a fracturing technology); 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    Development was made on a measuring instrument intended of acquiring information inside geothermal wells under high temperature and pressure. Research and development was performed on a fracturing technology to enhance characteristics of wells. What have been performed as a result of the development of the in-pit measuring instrument are application of high temperature logging cables as a result of development of logging devices, and the fabrication of a digital data analyzer. In developing the logging and reservoir evaluating technologies, field test were performed by using a logger that uses neutrons, installed with a radiation source. In developing the fracturing technology, discussions were given on the equation of relationship proposed from the standpoint of fracture dynamics, and investigations were made on examples of values, in order to anticipate hydraulic fracturing pressure applied in fracturing. In the research of fracturing additives, discussions were given on gelling agents supported by use of water glass, and alumina prop agents. For the preliminary observation devices, a high-pressure low flow rate control device was installed on the high-pressure plunger pump, improvement was made on the composite centrifugal multi-stage pump. (NEDO)

  4. Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

  5. 1998 report on development of high-efficiency waste power generation technology. 2. Development of waste gasification and ash melting power generation technology; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Haikibutsu gas ka yoyu hatsuden gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In regard to waste gasification and ash melting power generation, a basic test and examination were conducted in fiscal 1998, with a full-scale development test made ready to start. In the development of technology for raising steam temperature, evaluation of high temperature corrosivity of SH materials and development of high-temperature dust removal system were carried out for example, as were development of dechlorination technology for thermal decomposition process and development of ceramic high-temperature air heater. In the development of technology to prevent exhaust gas reheating, preliminary examination was made on denitrification technologies using a catalyst with superior low-temperature activity. In the development of technology to reduce self-heat melting critical calorific value, investigation and basic test were carried out concerning a stable waste feed system, with a pilot test device experimentally manufactured and tested based on the findings. In the development of technology for reducing external fuel input, examination and analysis were performed on pretreatment techniques for waste plastics, with basic data obtained for a waste blowing system project. In addition, the thermal decomposition and combustion characteristics of waste plastics were clarified by the basic test. (NEDO)

  6. Report on the surveys in fiscal 1999. Surveys on foundations for establishing industrial technology strategies (Strategies by fields - Bio technology field); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Bun'yabetsu gijutsu senryaku (Bio technology bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In order to deal with strengthening of competitive power in the bio-technological field and social requirements thereon, it was intended to establish target setting, ways to achieve the objectives, and technological strategies including extraction of policy problems, by combining the wisdom possessed by industries, governmental organizations, and academic world. Section 1 describes the result of the surveys on establishing technological strategies by fields. America tackles importantly with matters related to life science. Japan is strong in fermentation technologies, bio-reactors, and enzyme engineering. Japan stands nearly equal, or is slightly inferior to America in clone livestocks and bio-sensors. Japan's competitiveness is very low in such advanced technology fields as gene therapies, gene combined agricultural products, bio-agricultural chemicals, gene exploration technologies, and gene diagnosis. Section 2 describes technological strategies in four fields. To explain, the improvement in foundations to raise efficiencies in research and development and industrialization processes, strategies to place importance on such industrial fields as realizing 'wishes of people for happiness of diversified nature', the improvement of the environment in which people and societies can enjoy benefits brought about by growth of the industries, and structuring of institutions to promote industrialization of bio-technologies for the nation as a whole. (NEDO)

  7. Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

  8. Report on the invitation program for developing countries concerning technology promotion project of global environmental industry in FY 1997; 1997 nendo chikyu kankyo sangyo gijutsu suishin jigyo ni kakawaru chikyu kankyo kanren gijutsu kaigai kenkyusha shohei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In an effort to help preserve the global environment, International Center for Environmental Technology Transfer (ICETT) contributes to the solution of global environmental problems by promoting research exchanges with developing countries. As a part of this effort, ICETT hosted an environmental development researcher who visited Japan from the Institute of Environmental Research of Chulalongkorn University in Bangkok, Thailand. The invitation was extended at the request of NEDO. During the period of this investigation between September 16 and December 14, 1997, a photocatalyst was prepared and its performance was evaluated under the theme ``Application of photocatalysis to purification of atmospheric environment.`` At the same time, roadside test spots were inspected to study the practical application of optical photocatalysis. The visiting researcher also visited the National Institute for Resources and Environment to discuss with the staff of institute. This helped to deepen understandings of the state of air pollution problems confronting Japan, Europe, and North America, as well as issues related to the technologies that have been developed to solve these problems. The visiting researcher toured the RITE and examined Japan`s progress in the development of environmental control technology through joint research involving government, industry, and academia. At ICETT, the visiting researcher received training in Japan`s approaches to environmental problems in developing countries

  9. Fiscal 2000 report of investigation. Survey on technological trend concerning in si-tu remediation technology of contaminated soil; 2000 nendo osen dojo no gen'ichi joka gijutsu ni kakawaru gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In connection with contamination of soil and ground water, a survey was made on domestic patent information and existing literature or the like, in view of remediation technologies capable of in si-tu or on-site treatment, with arrangement and classification carried out by the method of cleaning contaminants. Arranged and classified were 209 pieces in the patent information, and 145 pieces in the literature from Geo-Environmental Protection Center, an incorporated body. In the methods of extracting contaminants from under the ground, the majority was the methods of pumping up ground water and those of excavating and removing. In the methods of cleaning contaminants, those of 'separation by heat', 'separation/decomposition method using water' and 'suction of gases' are found roughly in equal numbers. In the trend of the patent information, remediation technologies have started in 1990's, while bio-remediation as well as technologies of separation/decomposition through water is still increasing in the number of applications. Meantime, solidification technologies reached a peak around 1998 and have been decreasing in recent years. In the technologies of late, combinations of plural cleaning methods are also seen for the purpose of dealing with contamination with high to low concentration and compound contamination including organo-chloric compounds, heavy metals, etc. (NEDO)

  10. Fiscal 2000 report on result of R and D of nonmetallic material recycling promotion technology (demonstration test and research, total system technology); 2000 nendo hitetsu kinzokukei sozai recycle sokushin gijutsu kenkyu kaihatsu seika hokokusho. Jissho shiken kenkyu, total system gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted on advanced recycling technology for aluminum and base metal/rare metal based materials, with fiscal 2000 results compiled. In the research of aluminum recycling technology, on a continuous fractional crystallization process and a purification by zinc removal process, the existing facilities for each demonstrated that they could simulate an aluminum scrap melting process capacity of 1,000 t/month, with a series of initial conditions determined. In the research of total system technology, combined test facilities were completed in which a purification process and a melt cleaning process were integrated. In the research of the recycling technology for base metal/rare metal based materials, a test was carried out by demonstrative facilities, with the aim of establishing copper regeneration technology in which high grade copper is produced using metal/resin based scraps such as shredder dust of automobiles as the materials. In structuring the total system technology, a preliminary survey and environmental load measures were carried out toward the practicability of a comprehensive copper metal collection recycling system. (NEDO)

  11. FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

  12. Technique to increase performance of C-program for control systems. Compiler technique for low-cost CPU; Seigyoyo C gengo program no kosokuka gijutsu. Tei cost CPU no tame no gengo compiler gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    The software of automotive control systems has become increasingly large and complex. High level languages (primarily C) and the compilers become more important to reduce coding time. Most compilers represent real number in the floating point format specified by IEEE standard 754. Most microprocessors in the automotive industry have no hardware for the operation using the IEEE standard due to the cost requirements, resulting in the slow execution speed and large code size. Alternative formats to increase execution speed and reduce code size are proposed. Experimental results for the alternative formats show the improvement in execution speed and code size. 4 refs., 3 figs., 2 tabs.

  13. FY 1994 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1994 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This 5-year joint project (FY 1990 to 1994) by Japan and the Philippines is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized in the Philippines into electric power, in which thermal decomposition/gasification of the wastes is combined with a gas engine system. The field tests of the demonstration plant successfully produce power of 100 kW by burning only the low-calorie gas with a heating value near critical level for self-sustained combustion, obtained by gasification of sawdust by the fluidized gasifier and refined, attaining the object of the project. It is confirmed that a 200 to 300 kW class commercial plant can be designed and constructed basically by scaling up the 100 kW demonstration plant. The other data obtained by the field tests include those for improved operability and maintainability, gas purification, and reducing sizes of the facilities, including utility facilities. (NEDO)

  14. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  15. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  16. Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

  17. Fiscal 1999 leading research report. Research on advanced functional material technology based on micro- capsule technology; 1999 nendo micro capsule ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Study was made on production technology of the 5th- generation material 'eco-smart composite structure' based on micro-capsule technology. This material ought to have an intelligent function including self-detection and self- restoration of defects, environmental harmony, high strength and long life. At present, these demands are implemented by embedding a sensor, actuator and controller in structure, or optical fiber, shape memory alloy and computer chip in matrix, however, such complex material structure has adverse effect on environment. On the other hand, single structure material such as biodegradable polymer is unusable in severe environment such as the ocean and space. These problems can be resolved by combining composite material and micro-sphere technology, for example fiber-reinforced plastic (FRP) composite structure including micro-capsules with nano particles. According to targets, this material can have a self-restoration intelligent function, and other environment friendly functions such as easy decomposition, sound insulation, oscillation damping, electromagnetic shielding and hygroscopicity. (NEDO)

  18. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

  19. FY 1998 annual summary report on photon measuring/processing techniques. Development of highly functional maintenance techniques for power generating facilities; 1998 nendo foton keisoku kako gijutsu. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to develop the techniques for non-destructive measurement of conditions of facility portions, especially those exposed to severe environments, e.g., elevated temperature and pressure, over a wide range; the techniques for measurement of leakage of, e.g., gases, at high sensitivity; the techniques of laser-aided welding and surface-modification treatment for the members exposed to severe conditions; and the techniques for generating photon beams of high quality and energy density as the tools therefor, in order to improve reliability and maintenance efficiency of power generating facilities. The R and D themes are microscopic processing technology: fabrication technology for functional micro-composite circuits; in-situ status measuring technology: gas concentration/component measurement technology, and photon wavefront compensation device technology; non-destructive composition measuring technology: high-sensitivity detection technology using short-wavelength photons; high-power all-solid-state laser technology: rod-type laser and slab-type laser; tightly-focusing all-solid-state laser technology: high-energy pulse, high-quality laser; and comprehensive investigation of photonics engineering: investigation for photon-applied measurement technologies. (NEDO)

  20. Report on achievements in fiscal 1998. Development of useful substance production technology utilizing gene combination technology; 1998 nendo idenshi kumikae gijutsu wo riyoshita yuyo busshitsu seisan gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In developing a useful substance producing technology utilizing gene combination technology, plants are taken as a kind of useful substance producing arena, wherein useful protein genes of animals are introduced and manifested in the plants. Thereupon, technological development was carried out for the following items with regard to mass production of useful substances that can be utilized industrially, such as cytokine, by means of plant and cell cultivation: 1. Development of a useful substance producing technology utilizing gene combination technology, and 2. Comprehensive surveys and researches. For the technology to obtain and design useful substance producing genes originated from animals, development of a technology to search and acquire useful genes originated from animals, and a design and modification technology for useful genes. For the technology to introduce genes into gene combined plants, creation of plants combined with useful substance producing genes, and development of an introduction technology using plant virus vector. For the technology to produce high-function chemical substances in the gene combined plants, establishment of technologies for mass breeding and activity analysis of gene combined plants and cultivated cells, and for extraction and refinement of useful substances from the gene combined plants. In the comprehensive surveys and researches, technologies were surveyed and items of information were collected inside and outside the country. (NEDO)

  1. Technology for bonding silicon nitride ceramics. Heat treatment technology to improve diffusion bonding strength; Chikka keiso ceramics no setsugo gijutsu. Kakusan setsugo kyodo kaizen no tame no metsushori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M.; Shigematsu, K. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

    1999-01-25

    Silicon nitride ceramics is a structural ceramics with excellent high temperature strength and tenacity, being expected of expansion of application as a high temperature material. However, its processibility is poor, and special sintering technique is required to manufacture members of complex shapes. Therefore, development has been made on a technology to manufacture bonded materials with high mechanical strength, by which diffusion bonding in high temperature nitrogen gas and heat treatment are combined, and crystalline structure in the vicinity of bonding interface is controlled. (translated by NEDO)

  2. Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

  3. Fiscal 1997 technological survey report. R and D on micromachine technology (Development of high functional maintenance technology for power station equipment); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Activities were conducted in search of micromachine technology for a high functional maintenance system that inspects and repairs abnormal conditions such as cracks in a heat exchanger or a piping system without disassembling it in a power generating station such as a thermal or nuclear power plant. The activities were proceeded in four areas of (1) experimental manufacturing of the system (an inline self-running environment recognizing system, an external inspection system for fine tube group, and a system capable of light internal operation such as welding), (2) R and D on sophistication technology for functional devices, (3) R and D on common basic technologies, and (4) comprehensive investigation and research. In (1), examination of detailed basic specifications was carried out, as were examination of element technologies, experimental manufacturing and operation test of element devices, and performance evaluation. Further, a part of element devices was made on an experimental basis, with the basic functions demonstrated. In the comprehensive investigation and research, a trend in the future maintenance technology in power generating equipment was obtained and pigeonholed. (NEDO)

  4. Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of advanced maintenance technology for power plant facilities); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on R and D of measurement technology, laser welding and surface treatment technology, and generation technology of photon beam, for improvement of the quality and maintenance efficiency for power plant facilities. In the study on fabrication of functional micro-composite circuits, the equipment for forming circuits on substrates by carrying particles with gas was developed whose geometric standard deviation is 1.17 for 26nm particles. In the study on gas concentration measurement technology, development of the variable-wavelength laser beam source for measurement, fabrication of thin films by epitaxial growth equipment, and computer simulation of sensitivities for quantum IR photo- detectors were promoted. In the study on photon wavefront compensation device technology, the technology for fabricating such device with (411)A surface orientations and asymmetric quantum well structures was developed. In the study on high-sensitivity detection technology using short- wavelength photon, to develop a high-energy resolution fluorescent X-ray detector, favorable electric properties of superconducting X-ray detecting devices were confirmed at nearly 0.1K. (NEDO)

  5. FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)

  6. Survey of history/succession of industrial technology. Book of survey of the domestic industrial technology which contributed greatly to the industrial development; Sangyo gijutsu rekishi keisho chosa. Sangyo no hatten ni okiku kiyoshita kokunai sangyo gijutsu no chosahen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper surveyed a history of the industrial technology development which contributed to the innovation of technology in Japan for contribution to the future selection of technical themes and decision on developmental methods. In accordance with the increasing contribution of the Japanese industrial technology to scientific and economic activities in Japan and abroad, it is important to clarify a historical significance of the industrial technology and to make the most of results of the survey for the future succession/development of industrial technology. The survey focused on chemical processes brought up as the Japanese industrial technology which is regarded as world-famous and on the systematical study of the history of the Japanese scientific technology. Hereafter, this becomes a guiding principle for engineers. The paper arranged the survey results of production processes of 2-ethylhexanol, acrylic acid, acrylamide, and cresol/resorcinol, optical resolution process of amino acids, and flue gas desulfurization process. The paper also surveyed technologies of ammonia synthesis, coal liquefaction, high polymer film production and synthesis of medical raw materials. The results were obtained which are suggestive for developing creative/original technology. 210 refs., 93 figs., 49 tabs.

  7. FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  8. Survey and research for the enhancement of large-scale technology development 1. Japan's large-scale technology development and the effects; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 1. Nippon no daikibo gijutsu kaihatsu to sono koka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    A survey is conducted into the effects of projects implemented under the large-scale industrial technology research and development system. In the development of 'ultraperformance computers,' each of the technologies is being widely utilized, and the data service system of Nippon Telegraph and Telephone Public Corporation and the large computer (HITAC8800) owe much for their success to the fruits of the development endeavor. In the development of the 'desulfurization technology,' the fruits are in use by Tokyo Electric Power Co., Inc., and Chubu Electric Power Co., Inc., incorporated into their desulfurization systems. Although there is no practical plant based on the 'great-depth remotely controlled submarine oil drilling rig,' yet oceanic technologies and control methods are being utilized in various fields. The 'seawater desalination and by-product utilization' technologies have enabled the establishment of technologies of the top level in the world thanks to the resultant manufacture of concrete evaporator and related technologies. Eleven plants have been completed utilizing the fruits of the development. In the field of 'electric vehicle,' there is no commercialization in progress due to problems in cost effectiveness though remarkable improvement has been achieved in terms of performance. Technologies about weight reduction, semiconductor devices, battery parts and components, etc., are being utilized in many fields. (NEDO)

  9. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  10. FY 1998 annual summary report on photon measuring/processing techniques. Development of the techniques for high-efficiency production processes; 1998 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to develop the techniques for energy-efficient laser-aided processing; techniques for high-precision, real-time measurement to improve quality control for production processes and increase their efficiency; and the techniques for generating/controlling photon of high efficiency and quality as the laser beam sources therefor, in order to promote energy saving at and improve efficiency of production processes consuming large quantities of energy, e.g., welding, joining, surface treatment and production of fine particles. The R and D themes are microscopic processing technology: simulation technology for laser welding phenomena; microscopic processing technology: synthesis of technology for quantum dot functional structures; in-situ status measuring technology: fine particle elements and size measurement technology; high-power all-solid-state laser technology: efficient rod type LD-pumping laser modules and pumping chamber of a slab-type laser; tightly-focusing all-solid-state laser technology: improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology and fabrication technology for nonlinear crystal; and comprehensive investigation of photonics engineering: high-efficiency harmonic generation technology. (NEDO)

  11. Achievement report for fiscal 1981 on Sunshine Program. Practical application technologies for photovoltaic power systems (Development of peripheral technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu seika hokokusho. Shuhen gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    As for their outputs, the 3kW separately-excited and self-excited photovoltaic power plants yield daily averages of 7.8kWh and 6.9kWh, respectively, and this means that the self-excited type is inferior to the separately-excited type in terms of conversion efficiency. Automatic measuring devices for photovoltaic characteristics are installed at Sapporo, Sendai, Nagoya, and Miyazaki, which will elucidate regional difference in photovoltaic characteristics. A simulation of photovoltaic characteristics is performed and the resultant value is compared with the yield of an experimental 3kW system, and the result of the comparison is found reasonable. Cell arrays are subjected to investigation for configurations lowest in output loss for the respective shadow patterns. Harmonic characteristics are analyzed under plural-interconnection circumstances. Studies are made to miniaturize and simplify system constituents, and it is found that a 3-hour storage is proper for a 3kW-class storage battery. It is also found that a self-excited type suffers less voltage fluctuation in interconnected operation on a small short-circuit capacity system. Possibilities are that independent operation is started when output is larger than load, which is to be detected by checking changes in phase, frequency, etc. Array configuration, arresters, and shielding wires are taken up for the study of measures to cope with direct thunder strokes. (NEDO)

  12. Technological development report for fiscal 1993 on the woodwaste thermolysis/gasification technology and generated gas utilization technology; 1993 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The project is a joint effort of Japan and the Philippines to develop a thermolysis/gasification system, in which woodwaste now remaining unexploited in the Philippines is subjected to thermolysis/gasification and the resulting gas is used in a gas engine for the generation of electric power, in a 5-year period beginning in fiscal 1990. In this fiscal year, element technology verification tests are conducted, components of a demonstration plant are manufactured, and procurement is made as required, which completes all the tasks allotted to this fiscal year. All the constituents of the said demonstration plant fabricated or procured since fiscal 1991 are packed up and forwarded to Industrial Technology Development Institute (ITDI) of the Philippines, and engineering guidance is extended and test operations are carried out at the site of plant installation. In line with the said endeavors, on-site investigations are performed and researches are conducted together with ITDI scientists concerning the construction work and element technology confirmation. On the other hand, the Philippine side performs the second phase of civil engineering and construction carried over from the first phase. The demonstration plant is completed, adjustment and test operations are carried out, which means that the project is in progress as initially scheduled. (NEDO)

  13. Fiscal 2000 report of investigation. Survey on technological trend concerning in si-tu remediation technology of contaminated soil; 2000 nendo osen dojo no gen'ichi joka gijutsu ni kakawaru gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In connection with contamination of soil and ground water, a survey was made on domestic patent information and existing literature or the like, in view of remediation technologies capable of in si-tu or on-site treatment, with arrangement and classification carried out by the method of cleaning contaminants. Arranged and classified were 209 pieces in the patent information, and 145 pieces in the literature from Geo-Environmental Protection Center, an incorporated body. In the methods of extracting contaminants from under the ground, the majority was the methods of pumping up ground water and those of excavating and removing. In the methods of cleaning contaminants, those of 'separation by heat', 'separation/decomposition method using water' and 'suction of gases' are found roughly in equal numbers. In the trend of the patent information, remediation technologies have started in 1990's, while bio-remediation as well as technologies of separation/decomposition through water is still increasing in the number of applications. Meantime, solidification technologies reached a peak around 1998 and have been decreasing in recent years. In the technologies of late, combinations of plural cleaning methods are also seen for the purpose of dealing with contamination with high to low concentration and compound contamination including organo-chloric compounds, heavy metals, etc. (NEDO)

  14. Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

  15. FY 1999 report on the results of the R and D of genom informatics technology. Development of technology for rationalization of energy use; 1999 nendo genom informatics gijutsu kenkyu kaihtsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In this R and D, studies were made on the following: 1) development of a circular-shaped DNA-chip (DNA disk) and analysis of the gene expression pattern network by the DNA disk; 2) analytical system with DNA capillary array for mRNA expression profile; 3) development of protein probe technique for isolation of transcription factor complexes, and of evaluation technique for functions of transcription factors and their target DNAs; 4) transcription control information analytical technology - study of detection operational technology and preparation technology of transcription control information analytical specimens; 5) general R and D issues. In 1), development is conducted of DNA chips and a DNA chip system which makes use of DNA chips. In 2), development is made of a DNA capillary array and its accurate and high-speed reader to analyze expression profile of mRNA in various pathological processes of diseases of unknown etiology. In 3), as development of genom informatics technology, analysis of correlations is made, paying attention to transcription factors which become the key to gene expression. In 4), study is carried out of gene transcription control information high speed screening technology. (NEDO)

  16. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

  17. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

  18. Fiscal 1999 leading research report. Research on advanced functional material technology based on micro- capsule technology; 1999 nendo micro capsule ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Study was made on production technology of the 5th- generation material 'eco-smart composite structure' based on micro-capsule technology. This material ought to have an intelligent function including self-detection and self- restoration of defects, environmental harmony, high strength and long life. At present, these demands are implemented by embedding a sensor, actuator and controller in structure, or optical fiber, shape memory alloy and computer chip in matrix, however, such complex material structure has adverse effect on environment. On the other hand, single structure material such as biodegradable polymer is unusable in severe environment such as the ocean and space. These problems can be resolved by combining composite material and micro-sphere technology, for example fiber-reinforced plastic (FRP) composite structure including micro-capsules with nano particles. According to targets, this material can have a self-restoration intelligent function, and other environment friendly functions such as easy decomposition, sound insulation, oscillation damping, electromagnetic shielding and hygroscopicity. (NEDO)

  19. Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a technology to measure inside of wells (Development of a fracturing technology); 1980 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes the achievements in fiscal 1980 in developing a technology to measure inside of geothermal wells, and of fracturing (to achieve enhancement and regeneration of well performance). Design and fabrication were completed on the in-tunnel sensor for a neutron/density logger. The sensor withstood use at a temperature as high as 275 degrees C. In logging and reservoir evaluation field tests, reliable data were derived even at a depth of 1,800 m and a temperature of 250 degrees C. Characteristics of response of radioactivity logging (neutron and density logging) to different igneous rocks were investigated by using rock blocks. For the fracturing facilities, improvements were given on transportation performance and installation workability of the preliminary observation device, by utilizing the experience obtained in the previous fiscal year. A composite (divided into two units) centrifugal multi-stage pumping device was developed so that a water injection test can be performed in a wide capacity range according to the intended wells, where nearly satisfying performance was derived. For the fracturing technology, in order for even small test pieces to be capable of evaluating fracture tenacity accurately with consideration on nonlinear behavior of rocks, elasto-plastic fracture tenacity tests were carried out with AE measurement being performed simultaneously. The paper also describes studies on fracturing fluids. (NEDO)

  20. Achievement report for fiscal 1998 on the technological development of super metals. Technology to create iron-based mesoscopic tissue controlling materials; 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Tetsukei meso scopic soshiki seigyo zairyo sosei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development has been carried out on super metals with an objective to draw out properties possessed by iron and steel materials to their maximum extent and further enhance their recycling performance to make them friendly with global environment. The final goal of this project is to 'establish a technology to create micro tissue steel having crystalline particle diameter of about 1 {mu}mm or less and size having thickness of 1 mm or more by making the steel tissues uniform and multiple in phase'. The studies in the current fiscal year were moved forward mainly on obtaining ultra fine crystalline particles of 1 {mu}mm or less, identifying the ideal large distortion processing conditions, and structuring the guidance principles for ultra-fine micronization of the crystalline particles by using large distortion processing. Discussions were also launched on further micronization of crystalline particles by optimizing chemical composition and on expansion of the process windows assuming practical application thereof in industrial scale. Furthermore, material property evaluation was also begun on ultra-fine crystalline particle materials of smaller than 1{mu}mm. As the mesoscopic structure analyzing technology for the ultra-fine crystalline particle materials, an in-lens resolution SEM was introduced, and the basic method was established. (NEDO)

  1. FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

  2. Survey and research on the effects of technological development. Annex (Tables of technology-related data); Gijutsu kaihatsu no koka ni kansuru chosa kenkyu. Bessatsu (gijutsu kanren data list)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Compiled into a report are the data about trends in Japan's research and development efforts broken down by industry covering a period of 1960-1980. The data items are quite versatile, including the number of companies engaged in researches and their rates, number of employees, total sales volume, profits through business, number of employees related to researches, number of dedicated researchers, number of dedicated researchers per 10,000 employees, disbursement of in-house research expenses, rate of personnel expenses to in-house research expenses, rate of disbursement of in-house research expenses to total sales volume, rate of disbursement of in-house research expenses to profits through business, disbursement of in-house research expenses per company, disbursement of in-house research expenses per dedicated researcher, in-house research expenses broken down by purpose (basic research, applied research, research for development), component ratio (basic research, applied research, research for development), number of dedicated researchers per speciality (total number, mathematics and physics, chemistry, biology, geology, engineering, civil engineering and construction, machinery and ship and aviation, electricity and communication, mining and metallurgy, textile, agriculture and forestry, fishery, stock-breeding and veterinarian, medicine and dentistry, pharmacy), number of technologies exported, total sum of export, etc. (NEDO)

  3. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  4. Rising economy of China and its effects on the industrial technology of Japan and other Asian countries. Chugoku no hatten to henbosuru Asia no sangyo gijutsu chizu (henkaku wo semarareru seisan gijutsu taikoku Nippon)

    Energy Technology Data Exchange (ETDEWEB)

    Otani, H [JGC Corp., Tokyo (Japan)

    1994-03-05

    Due to the rapid economy growth and industry development in China, the map of industry and economy in Asian countries has been greatly changing. The technology, which has supported Japan's industrial development, is characterized by the improvements of original technologies introduced from Europe and the United States. On the other hand, Korea has problems of creating the original and individual production technology and its basis. The industrial technology in China at present has problems which are accompanied with the conversion from the planned economy system to the market economy system. However, Chinese people having a tradition of 'link of three parts' seem to understand the Japanese style management policy well. Japan has played a role as 'world's center of manufacturing' by using its excellent production technology. In the future, China is considered to play a role as the 'world's center of manufacturing,' due to its huge domestic market, cheap and rich manpower, and excellent potential capacity of industrial technology. In Japan, it is emphasized that an industrial society system should be reconstructed, in which excellent individuality and talent can be made good use of. 6 refs., 1 fig.

  5. FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

  6. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  7. Technologies and techniques for analysis and use of genome information, 1997; Genome joho kaidoku riyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper clarified the whole image of cell functions by elucidating the function and manifestation control mechanism of genes existing in genomes, and the network of their interactions, and surveyed applicability of the useful functions obtained of cells and proteins to the industrial field. The survey was made from a viewpoint of the fields of both biology and information science. Especially, based on the function-known DNA base sequence database, the following technologies were surveyed: technology to predict the function of the function-unknown DNA base sequence, search/separation technology to acquire the genes to be functionally elucidated in a state of being suitable for manifestation, technology to get perfect proteins by effectively manifesting the genes to be functionally elucidated, and technology to analyze the function of the proteins obtained by manifestation of genes. Further, the International Symposium was held which is titled `Genome Research Opens a New World to Bioindustry (New Developments in Genome Informatics Technologies). With the future progress of technology to decipher and use genome information, the construction of much newer genome industry is anticipated. 165 refs., 44 figs., 10 tabs.

  8. Transition of wind power utilization technology in the 20th century; 20 seiki ni okeru furyoku riyo gijutsu no hensen

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Inst. of Tech., Tochigi (Japan)

    2000-04-01

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at the end of 19{sup th} century. This paper, at first, reviews the windmill technologies and the researchers before 20th century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  9. Phosphorus and nitrogen removal in waste water at small factory. Shokibo jigyosho ni okeru haisuichu no rin chisso shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirai, M. (National Institute for Resources and Environment, Tsukuba (Japan))

    1994-05-25

    For the purpose of preventing closed waters from eutrophicating, COD regulations and nitrogen and phosphorus waste water regulations are executed in Japan, but practically applicable techniques for this purpose are a few. Concerning technology for removing nitrogen and phosphorus in waste water, this paper describes the actual situation of two industries, electroplating and alumite processing, and applicable techniques. Among various nitrogen removal methods, the biological treatment method has been used practically in many cases and is applicable to practical use. While there are many kinds of physical and chemical treatment methods, applicable methods are limited. In removing nitrogen, the coagulating sedimentation method with Ca salt, Al salt and Fe salt is effective generally for orthophosphate. At electroplating factories, various forms of phosphorus and nitrogen compounds are used as plating chemicals. In treating waste water containing phosphorus, the coagulating sedimentation method is used most frequently. The oxidation + coagulating sedimentation method, the autolysis + oxidation coagulation method, and the evaporation method are effected, though the examples of their implementation are small in number. 15 tabs.

  10. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

  11. Report on investigation in fiscal 2000 of industrial technology information; 2000 nendo sangyo gijutsu joho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Pursuing the measures for how the national research institutions in Japan who have been made into independent administrative corporations should be positioned in maintaining and developing the industrial strength, investigations were performed with the points focused on measures taken in the United States to improve research environment, and the ways the national research institutions should be. The investigation results were summarized on the following four areas: 1) transition of research and development policies, 2) on the national research organizations, 3) structuring of database for researchers in universities and national research organizations, and 4) future challenges and suggestions. Item 1) has put the subject into order of the history of establishing legislations related to the U.S. technological policies, measures to promote research and development, budgetary management, grants, and preferential treatment. In Item 2), visits and investigations were executed on government-owned, government-operated laboratories and government-owned, contractor-operated laboratories whose operation patterns are different with each other. The results were put into order of institutions, roles, personnel systems, activation measures, joint research institutions, and finance. In Item 3), a data list was prepared on researchers relative to advanced technology programs contributing greatly to enhancing the competitive edge of U.S. corporations. (NEDO)

  12. Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

  13. On-line sensor technology for food manufacturing industry. Shokuhin bun prime ya ni okeru on-line sensor gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Komiya, K. (Ajinomoto Co. Inc., Tokyo (Japan))

    1990-08-05

    This paper introduced the sensor technology for food manufacturing industry. If sugar concentration in main raw material is too high in the amino acid fermentation, control of the concentration is required because fungi growth is inhibited. A controlling method for sugar concentration was developed by using the correlation between consumption of NH {sub 3} for pH adjustment and sugar consumption in place of conventional analyzing method and was introduced in the gulutamic acid fermantation. BOD sensor was developed to enable the selective measurement of organic substances which can be processed by organisms, and measuring time was shortened from previous five days to 30 minutes. Since many organics absorb infrared ray, near infrared analysis is suitable for food analysis and on-line analysis has high possibility. When this method is applied to measure moisture in fishes and meats, continuous measurement can be made nondestructively and without contacting, and further the precision is {plus minus} 0.1%. Simultaneous multi-composition analyses are carried out by continuous spectrum and near infrared method using higher rate scanning. Sensor development for taste and smell has started. 10 refs., 4 figs., 4 refs.

  14. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  15. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Electronic information technology field (Human process ware field for computers); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chsao hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) denshi joho gijutsu bun'ya (computer kanren bun'ya no uchi, human process wear bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a human process ware (HPW) field on electronic information. Although the current HPW industry is not yet complete, various technologies concerned are being stored, and the HPW industry is expected as new major industry for home and personal information equipment. As factors hindering technological innovation in Japan, the incomplete market, poor cooperation between industry and government, ambiguous role of university, and poor standardization were pointed out. Technology trends were analyzed to extract seed technology fields from 3 viewpoints of mobile HPW available at any time, at any place and to anybody, HPW system capable of customizing every personal use, and HPW supporting development of a creativity. As general strategy, the technology seed chart and map of technical development targets for every HPW were prepared to conceive a route to practical use, and develop element technologies required for practical use, based on the future trend of the market. (NEDO)

  16. Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

  17. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  18. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

  19. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

  20. Fiscal 2000 pioneering research on the spintronic device basic technology; 2000 nendo spintronic soshi kiban gijutsu sendo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researchers specializing in technologies of magnetism or semiconductor were drafted from the industrial, official, and academic circles, who conducted hearings, patent investigations, overseas surveys, and the like, concerning spintronics. Collected in this report are the outline of the research and development of spintronic device technology, its current state and tasks and its importance from social and economic viewpoints, and the strategy that Japan should follow in the research and development of the technology. Important spintronic device technologies now attracting attention are mentioned below. The nonvolatile magnetic memory device MRAM (magnetic random access memory) is supposed to be the device which will enjoy practical application first among like devices. It is expected that the spin conduction device will lead to novel functions when the possibilities of the spin-dependent electric conduction phenomenon are further pursued. It is hoped that the spin optical device will be used as a light isolator, light spin logic device, field induced variable wavelength laser device, spin laser device, high-speed light switch, and so forth. It is necessary to watch the development of a spin-aided quantum computer which is still at the stage of basic study. (NEDO)

  1. Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-04-20

    Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

  2. Development of magnesium semi-solid injection molding; Magnesium han`yoyu shashutsu seikei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakamoto, K; Sakate, N; Ishida, K; Yamamoto, Y; Nishimura, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    Magnesium semi-solid injection molding is safety and clean process. We have investigated influence of molding conditions on mechanical properties and dimension accuracy of products by semi-solid injection molding. As a result it was proved that the accuracy of products by this process is superior to die casting. This advantage as well as better mechanical properties can be utilized for net shape molding of some automobile parts. 4 refs., 8 figs., 3 tabs.

  3. Development of regeneration technique for diesel particulate filter made of porous metal; Kinzoku takotai DPF no saisei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoro, K; Ban, S; Ooka, T; Saito, H; Oji, M; Nakajima, S; Okamoto, S [Sumitomo Electric Industries, Ltd., Osaka (Japan)

    1997-10-01

    We have developed the diesel particulate filter (DPF) in which porous metal is used for a filter because of its high thermal conductivity and a radiation heater is used for a regeneration device because of its uniform thermal distribution. In the case high trapping efficiency is required, filter thickness should be thick. The thicker filter has a disadvantage of difficulty in regeneration because of the thermal distribution in the direction of thickness. In order to improve regeneration efficiency, we designed the best filter-heater construction which achieves uniform thermal distribution by using computer simulation and we confirmed good regeneration efficiency in the experiment. 4 refs., 14 figs., 1 tab.

  4. Development of three-dimensional pipe bending technology; Pipe zai no sanjigen mage kako gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, K; Takeda, S [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, automotive parts uses move resin products or pipe-like products in order to achieve high quality or light weight. Additionally, the shape of automotive parts becomes more complicated. The rotary stretch bending method, although it is most popular method of bending a pipe, has some problems, such as a bending radius is limited due to use of bending mold, a thickness of an outer side of a bending portion is thinner, and a product is scratched easily during manufacturing. We have developed a three dimensional pipe bending process using a floating expanding plug and confirmed that this method can solve the above problems. 2 refs., 9 figs., 3 tabs.

  5. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - chemical/process field (chemical/process technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kagaku process bun'ya (kagaku process gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to long-term energy technology strategy, the paper described the results of the FY 1999 survey of chemical/process technology. The future chemical technology should be transformed from the material production technology in which priority used to be given to convenience to new chemical technology in which the functions needed are to be created. The shortage of the developmental period and minimization of the waste are also desired by the use of new methods. For it, the industry/government/university should gather wisdom together and fulfil the requests from other industries of the country under the circumstances of the society which is aging, is decreasing in birthrate, and is being highly information-or