WorldWideScience

Sample records for technology process options

  1. The Decision of Enterprises during the Process of Technological Innovation Diffusion Based on Real Option Theory

    Directory of Open Access Journals (Sweden)

    Guozhong Yang

    2014-05-01

    Full Text Available Based on real option theory, the article analyses the decision-making of enterprises during the process of technological innovation diffusion under an uncertain circumstance. Under the assumption that the returns of enterprises follow geometric Brownian motion, the article firstly estimates the transition value of imitating technology innovators and the average latency of imitation, then it analyses the influence of every parameter on the diffusion process. It can be concluded that both the market demand and the rate have significant effects on the diffusion rate of innovative technology.

  2. Process and technological options for odorous emissions control in wastewater treatment plants

    International Nuclear Information System (INIS)

    Cernuschi, S.; Torretta, V.

    1996-01-01

    The emissions of odorous substances together with noise and issues related to proper architectural design within the existing territorial context, have certainly to be considered one of the most significant environmental effects determined by wastewater treatment plants particularly in the most frequent case of their localization in dense urban areas. Following a brief introduction on the chemical properties of odorous compounds and the corresponding methods for representing their concentration levels in air, present work reports on the main qualitative and quantitative characteristics of odorous emissions originating from single unit operations of typical wastewater treatment plants and on the technological and process options available for their control

  3. Nuclear technology options

    International Nuclear Information System (INIS)

    Salvatores, Massimo

    2013-01-01

    Different strategies and motivations in different countries have led to diverse options. In Europe the SNETP (Sustainable Nuclear Energy Technology Platform) has the objective of developing R&D supporting GEN-II (present) and GEN-III nuclear systems under development; allowing sustainability and minimisation of waste burden, promoting advanced Gen-IV Fast Reactors; and accounting for a Nuclear Cogeneration Industrial Initiative. A remarkable initiative in the USA has been the promotion of small modular reactors (SMRs) – at less than 300 MWe in capacity, much smaller than typical reactors – which can be an ideal choice for (remote) areas which cannot support a larger reactor. Compact scalable design offers a host of potential safety, construction and economic benefits. More “upbeat” strategies are expected in other areas of the world where significant increase in nuclear energy demand is predicted in the next decades. If this growth materialises, future fuel cycles characteristics, feasibility and acceptability will be crucial. This paper will discuss different scenarios for future fuel cycles, resources optimisation and/or waste minimization, the range from full fast reactor deployment to phase-out, management of spent nuclear fuel and the significant potential benefits of advanced cycles. The next 45 years will be dominated by deployment of standard large or medium size plants operating for 60 years. Available resources do allow it. However, fuel cycle will be a growing and most challenging issue and early assessments will be needed for public acceptance and policy decisions.

  4. Technology options for future recycling

    International Nuclear Information System (INIS)

    Kikuchi, T.

    2001-01-01

    Recycling of nuclear material is indispensable, not only for using valuable resources but also for reducing the debt which we may leave to the next generations. Advanced reprocessing technologies have been developed in several countries to deal with the diversification of nuclear fuels. Also technologies derived from reprocessing or other fuel cycle areas have continued to be developed in terms of recycling. Cost effectiveness and waste-free processing are increasingly important factors in the applicable of an alternate recycling policy. This paper introduces an example of the studies in this field conducted in some countries including Japan and considers the establishment of effective recycling methodologies taking into account the uncertainty of future recycling policy. (author)

  5. Technology options for future recycling

    International Nuclear Information System (INIS)

    Kikuchi, T.

    2000-01-01

    It goes without saying that recycling of nuclear material is indispensable, not only for the effective use of valuable resources but also to reduce the debt which we may leave to the next generations. Many developments in advanced reprocessing technologies have been carried out in several countries to deal with the diversification of nuclear fuels. Also technologies derived from reprocessing or other fuel cycle areas have continued to be developed in terms of recycling. Cost effectiveness and waste-free processing are increasingly important factors in the applicable of an alternate recycling policy. This paper introduces an example of the studies in this field, which has been conducted in Japan and considers the establishment of effective recycling methodologies taking into account the uncertainty of future policy. (authors)

  6. TECHNOLOGICAL OPTIONS FOR ACID RAIN CONTROL

    Science.gov (United States)

    Discussed are acid rain control options available to the electric utility industry. They include coal switching, flue gas desulfurization, and such emerging lower cost technologies as Limestone Injection Multistage Burners (LIMB) and Advanced Silicate (ADVACATE), both developed ...

  7. Technological options for acid rain control

    International Nuclear Information System (INIS)

    Princiotta, F.T.; Sedman, C.B.

    1993-01-01

    The paper discusses technological options for acid rain control. Compliance with Title IV of the Clean Air Act Amendments of 1990 will require careful scrutiny of a number of issues before selecting control options to reduce sulfur dioxide (SO2) and nitrogen oxide (NOx) emissions. One key consideration is the effect of fuel switching or control technology upon the existing dust collector, with additional air toxics legislation looming ahead. A number of likely SO2 and NOx retrofit technologies and estimated costs are presented, along with results of retrofit case studies. New hybrid particulate controls are also being developed to meet future requirements

  8. Development of Process for Disposal of Plastic Waste Using Plasma Pyrolysis Technology and Option for Energy Recovery

    Czech Academy of Sciences Publication Activity Database

    Punčochář, Miroslav; Ruj, B.; Chatterj, P.K.

    2012-01-01

    Roč. 42, SI (2012), s. 420-430 E-ISSN 1877-7058. [International Congress of Chemical and Process Engineering CHISA 2012 and 15th Conference PRES 2012 /20./. Prague, 25.08.2012-29.08.2012] Institutional support: RVO:67985858 Keywords : plastic waste * plasma pyrolysis * syngas Subject RIV: CI - Industrial Chemistry, Chemical Engineering

  9. Technological options for the management of biosolids.

    Science.gov (United States)

    Wang, Hailong; Brown, Sally L; Magesan, Guna N; Slade, Alison H; Quintern, Michael; Clinton, Peter W; Payn, Tim W

    2008-06-01

    provide a complete management for biosolids. A number of advanced thermal conversion technologies (e.g., supercritical water oxidation process and pyrolysis) are under development for biosolids management with a goal to generate useful products, such as higher quality fuels and recovery of phosphorus. With an ever-increasing demand for renewable energy, growing bioenergy crops and forests using biosolids as a fertilizer and soil amendment can not only contribute to the low-carbon economy but also maximize the nutrient and carbon value of the biosolids. Land application of biosolids achieves a complete reuse of its nutrients and organic carbon at a relatively low cost. Therefore, land application should become a preferred management option where there is available land, the quality of biosolids meet regulatory requirements, and it is socially acceptable. Intensive energy cropping and forest production using biosolids can help us meet the ever-increasing demand for renewable energy, which can eliminate the contamination potential for food sources, a common social concern about land application of biosolids. In recent years, increasing numbers of national and local governments have adopted more stringent regulations toward biosolid management. Under such a political climate, biosolids producers will have to develop multireuse strategies for biosolids to avoid being caught because a single route management practice might be under pressure at a short notice. Conventional incineration systems for biosolids management generally consume more energy than they produce and, although by-products may be used in manufacturing, this process cannot be regarded as a beneficial use of biosolids. However, biosolids are likely to become a source of renewable energy and produce 'carbon credits' under the increasingly popular, low-carbon economy policy. To manage biosolids in a sustainable manner, there is a need for further research in the following areas: achieving a higher degree of public

  10. Processing options for bitumen upgrading

    International Nuclear Information System (INIS)

    Harji, A.N.; Koppel, P.E.; Mazurek, W.L.; Meysami, P.

    2003-01-01

    It is estimated that 178 billion barrels of oil can be recovered from Alberta's vast heavy oil reserves. The challenge lies in the logistics of recovering, upgrading and transporting the oil to market. The Canadian Energy Research Institute conducted a recent study to determine market potential by 2007 for diluted bitumen and synthetic crude oil produced from upgraded bitumen. The viability for a wide range of bitumen feedstocks was assessed along with the sensitivity of refinery demand to their prices. The 3 major markets for western Canadian bitumen include PADD 2 in the United States, western Canada, and Ontario. Bitumen is too viscous to transport by pipeline and cannot be processed by most of the existing refineries. Therefore, in order to develop a mass market for the product, bitumen must undergo the energy intensive upgrading process at existing refineries. The factors impacting which method of upgrading is most suitable were discussed with particular attention to the impact that Canada's ratification of the Kyoto Protocol may have on Alberta's bitumen resource in terms of costs of complying with greenhouse gas reduction initiatives. The authors emphasized that it is crucial to customize an upgrading project to meet site and market specific factors. 8 refs., 3 tabs., 3 figs

  11. European consumers' acceptance of beef processing technologies

    DEFF Research Database (Denmark)

    de Barcellos, Marcia Dutra; Kügler, Jens Oliver; Grunert, Klaus G.

    2010-01-01

    ' beef were considered negative outcomes of technological innovations. Beef processing technologies were predominantly perceived as valuable options for convenience shoppers and less demanding consumers. Overall, respondents supported the development of 'non-invasive' technologies that were able...

  12. Multibunch feedback: Strategy, technology and implementation options

    International Nuclear Information System (INIS)

    Fox, J.D.; Eisen, N.; Hindi, H.; Oxoby, G.; Sapozhnikov, L.; Linscott, I.; Serio, M.

    1992-10-01

    The proposed next generation accelerator and synchrotron light facilities will require active feedback systems to control multi-bunch instabilities. These feedback systems must operate in machines with thousands of circulating bunches and with short (2--4 ns) interbunch intervals. The functional requirements for transverse (betatron) and longitudinal (synchrotron) feedback systems are presented. Several possible implementation options are discussed and system requirements developed. Results are presented from a digital signal processing based synchrotron oscillation damper operating at the SSRL/SLAC SPEAR storage ring

  13. Process to identify and evaluate restoration options

    International Nuclear Information System (INIS)

    Strand, J.; Senner, S.; Weiner, A.; Rabinowitch, S.; Brodersen, M.; Rice, K.; Klinge, K.; MacMullin, S.; Yender, R.; Thompson, R.

    1993-01-01

    The restoration planning process has yielded a number of possible alternatives for restoring resources and services injured by the Exxon Valdez oil spill. They were developed by resource managers, scientists, and the public, taking into consideration the results of damage assessment and restoration studies and information from the scientific literature. The alternatives thus far identified include no action natural recovery, management of human uses, manipulation of resources, habitat protection and acquisition, acquisition of equivalent resources, and combinations of the above. Each alternative consists of a different mix of resource- or service-specific restoration options. To decide whether it was appropriate to spend restoration funds on a particular resource or service, first criteria had to be developed that evaluated available evidence for consequential injury and the adequacy and rate of natural recovery. Then, recognizing the range of effective restoration options, a second set of criteria was applied to determine which restoration options were the most beneficial. These criteria included technical feasibility, potential to improve the rate or degree of recovery, the relationship of expected costs to benefits, cost effectiveness, and the potential to restore the ecosystem as a whole. The restoration options considered to be most beneficial will be grouped together in several or more of the above alternatives and presented in a draft restoration plan. They will be further evaluated in a companion draft environmental impact statement

  14. Which is the best solar thermal collection technology for electricity generation in north-west India? Evaluation of options using the analytical hierarchy process

    International Nuclear Information System (INIS)

    Nixon, J.D.; Dey, P.K.; Davies, P.A.

    2010-01-01

    This study of concentrating solar thermal power generation sets out to evaluate the main existing collection technologies using the framework of the Analytical Hierarchy Process (AHP). It encompasses parabolic troughs, heliostat fields, linear Fresnel reflectors, parabolic dishes, compound parabolic concentrators and linear Fresnel lenses. These technologies are compared based on technical, economic and environmental criteria. Within these three categories, numerous sub-criteria are identified; similarly sub-alternatives are considered for each technology. A literature review, thermodynamic calculations and an expert workshop have been used to arrive at quantitative and qualitative assessments. The methodology is applied principally to a case study in Gujarat in north-west India, though case studies based on the Sahara Desert, Southern Spain and California are included for comparison. A sensitivity analysis is carried out for Gujarat. The study concludes that the linear Fresnel lens with a secondary compound parabolic collector, or the parabolic dish reflector, is the preferred technology for north-west India.

  15. Which is the best solar thermal collection technology for electricity generation in north-west India? Evaluation of options using the analytical hierarchy process

    Energy Technology Data Exchange (ETDEWEB)

    Nixon, J.D.; Davies, P.A. [Sustainable Environment Research Group, School of Engineering and Applied Science, Aston University, Aston Triangle, Birmingham, B4 7ET (United Kingdom); Dey, P.K. [Aston Business School, Aston University, Aston Triangle, Birmingham, B4 7ET (United Kingdom)

    2010-12-15

    This study of concentrating solar thermal power generation sets out to evaluate the main existing collection technologies using the framework of the Analytical Hierarchy Process (AHP). It encompasses parabolic troughs, heliostat fields, linear Fresnel reflectors, parabolic dishes, compound parabolic concentrators and linear Fresnel lenses. These technologies are compared based on technical, economic and environmental criteria. Within these three categories, numerous sub-criteria are identified; similarly sub-alternatives are considered for each technology. A literature review, thermodynamic calculations and an expert workshop have been used to arrive at quantitative and qualitative assessments. The methodology is applied principally to a case study in Gujarat in north-west India, though case studies based on the Sahara Desert, Southern Spain and California are included for comparison. A sensitivity analysis is carried out for Gujarat. The study concludes that the linear Fresnel lens with a secondary compound parabolic collector, or the parabolic dish reflector, is the preferred technology for north-west India. (author)

  16. Technology assessment of various coal-fuel options

    International Nuclear Information System (INIS)

    Coenen, R.; Findling, B.; Klein-Vielhauer, S.; Nieke, E.; Paschen, H.; Tangen, H.; Wintzer, D.

    1991-01-01

    The technology assessment (TA) study of coal-based fuels presented in this report was performed for the Federal Ministry for Research and Technology. Its goal was to support decision-making of the Federal Ministry for Research and Technology in the field of coal conversion. Various technical options of coal liquefaction have been analyzed on the basis of hard coal as well as lignite -- direct liquefaction of coal (hydrogenation) and different possibilities of indirect liquefaction, that is the production of fuels (methanol, gasoline) by processing products of coal gasification. The TA study takes into consideration the entire technology chain from coal mining via coal conversion to the utilization of coal-based fuels in road transport. The analysis focuses on costs of the various options, overall economic effects, which include effects on employment and public budgets, and on environmental consequences compared to the use of liquid fuels derived from oil. Furthermore, requirements of infrastructure and other problems of the introduction of coal-based fuels as well as prospects for the export of technologies of direct and indirect coal liquefaction have been analyzed in the study. 14 figs., 10 tabs

  17. Sustainable sanitation technology options for urban slums.

    Science.gov (United States)

    Katukiza, A Y; Ronteltap, M; Niwagaba, C B; Foppen, J W A; Kansiime, F; Lens, P N L

    2012-01-01

    Poor sanitation in urban slums results in increased prevalence of diseases and pollution of the environment. Excreta, grey water and solid wastes are the major contributors to the pollution load into the slum environment and pose a risk to public health. The high rates of urbanization and population growth, poor accessibility and lack of legal status in urban slums make it difficult to improve their level of sanitation. New approaches may help to achieve the sanitation target of the Millennium Development Goal (MDG) 7; ensuring environmental sustainability. This paper reviews the characteristics of waste streams and the potential treatment processes and technologies that can be adopted and applied in urban slums in a sustainable way. Resource recovery oriented technologies minimise health risks and negative environmental impacts. In particular, there has been increasing recognition of the potential of anaerobic co-digestion for treatment of excreta and organic solid waste for energy recovery as an alternative to composting. Soil and sand filters have also been found suitable for removal of organic matter, pathogens, nutrients and micro-pollutants from grey water. Copyright © 2012 Elsevier Inc. All rights reserved.

  18. Wastewater and sludge control-technology options for synfuels industries

    Energy Technology Data Exchange (ETDEWEB)

    Castaldi, F.J.; Harrison, W.; Ford, D.L.

    1981-02-01

    The options examined were those of zero discharge, partial water reuse with restricted discharge of treated effluents, and unrestricted discharge of treated effluents. Analysis of cost data and performance-analyses data for several candidate secondary-wastewater-treatment unit processes indicated that combined activated-sludge/powdered-activated-carbon (AS/PAC) treatment incorporating wet-air-oxidation carbon regeneration is the most cost-effective control technology available for the removal of organic material from slagging, fixed-bed process wastewaters. Bench-scale treatability and organic-constituent removal studies conducted on process quench waters from a pilot-scale, slagging, fixed-bed gasifer using lignite as feedstock indicated that solvent extraction followed by AS/PAC treatment reduces levels of extractable and chromatographable organics to less than 1 ..mu..g/L in the final effluent. Levels of conventional pollutants also were effectively reduced by AS/PAC to the minimum water-quality standards for most receiving waters. The most favored and most cost-effective treatment option is unrestricted discharge of treated effluents with ultimate disposal of biosludges and landfilling of gasifier ash and slag. This option requires a capital expenditure of $8,260,000 and an annual net operating cost of $2,869,000 in 1978 dollars, exclusive of slag disposal. The net energy requirement of 19.6 x 10/sup 6/ kWh/year, or 15.3 kWh/1000 gal treated, is less than 6% of the equivalent energy demand associated with the zero-discharge option.

  19. Effectiveness of technological options for minimising production ...

    African Journals Online (AJOL)

    Farmer perceptions of technology effectiveness, to some extent, agreed with econometric evidence from this study. Study results have two implications: firstly, the need to develop and disseminate location specific adaptation technologies to reduce production risks, instead of blanket recommendations of similar adaptation ...

  20. American option pricing with stochastic volatility processes

    Directory of Open Access Journals (Sweden)

    Ping LI

    2017-12-01

    Full Text Available In order to solve the problem of option pricing more perfectly, the option pricing problem with Heston stochastic volatility model is considered. The optimal implementation boundary of American option and the conditions for its early execution are analyzed and discussed. In view of the fact that there is no analytical American option pricing formula, through the space discretization parameters, the stochastic partial differential equation satisfied by American options with Heston stochastic volatility is transformed into the corresponding differential equations, and then using high order compact finite difference method, numerical solutions are obtained for the option price. The numerical experiments are carried out to verify the theoretical results and simulation. The two kinds of optimal exercise boundaries under the conditions of the constant volatility and the stochastic volatility are compared, and the results show that the optimal exercise boundary also has stochastic volatility. Under the setting of parameters, the behavior and the nature of volatility are analyzed, the volatility curve is simulated, the calculation results of high order compact difference method are compared, and the numerical option solution is obtained, so that the method is verified. The research result provides reference for solving the problems of option pricing under stochastic volatility such as multiple underlying asset option pricing and barrier option pricing.

  1. Financial options methodology for analyzing investments in new technology

    Science.gov (United States)

    Wenning, B. D.

    1995-01-01

    The evaluation of investments in longer term research and development in emerging technologies, because of the nature of such subjects, must address inherent uncertainties. Most notably, future cash flow forecasts include substantial uncertainties. Conventional present value methodology, when applied to emerging technologies severely penalizes cash flow forecasts, and strategic investment opportunities are at risk of being neglected. Use of options evaluation methodology adapted from the financial arena has been introduced as having applicability in such technology evaluations. Indeed, characteristics of superconducting magnetic energy storage technology suggest that it is a candidate for the use of options methodology when investment decisions are being contemplated.

  2. Financial options methodology for analyzing investments in new technology

    International Nuclear Information System (INIS)

    Wenning, B.D.

    1994-01-01

    The evaluation of investments in longer term research and development in emerging technologies, because of the nature of such subjects, must address inherent uncertainties. Most notably, future cash flow forecasts include substantial uncertainties. Conventional present value methodology, when applied to emerging technologies severely penalizes cash flow forecasts, and strategic investment opportunities are at risk of being neglected. Use of options valuation methodology adapted from the financial arena has been introduced as having applicability in such technology evaluations. Indeed, characteristics of superconducting magnetic energy storage technology suggest that it is a candidate for the use of options methodology when investment decisions are being contemplated

  3. Integrated assessment of bioelectricity technology options

    International Nuclear Information System (INIS)

    Thornley, Patricia; Upham, Paul; Huang, Ye; Rezvani, Sina; Brammer, John; Rogers, John

    2009-01-01

    Power generation from biomass is a sustainable energy technology which can contribute to substantial reductions in greenhouse gas emissions, but with greater potential for environmental, economic and social impacts than most other renewable energy technologies. It is important therefore in assessing bioenergy systems to take account of not only technical, but also environmental, economic and social parameters on a common basis. This work addresses the challenge of analysing, quantifying and comparing these factors for bioenergy power generation systems. A life-cycle approach is used to analyse the technical, environmental, economic and social impacts of entire bioelectricity systems, with a number of life-cycle indicators as outputs to facilitate cross-comparison. The results show that similar greenhouse gas savings are achieved with the wide variety of technologies and scales studied, but land-use efficiency of greenhouse gas savings and specific airborne emissions varied substantially. Also, while specific investment costs and electricity costs vary substantially from one system to another the number of jobs created per unit of electricity delivered remains roughly constant. Recorded views of stakeholders illustrate that diverging priorities exist for different stakeholder groups and this will influence appropriate choice of bioenergy systems for different applications

  4. effectiveness of technological options for minimising production risks

    African Journals Online (AJOL)

    ACSS

    preferred technologies in reducing production risk related to climate variability in Eastern Uganda. Data for this study were ..... Set of technological options employed by farmers to reduce climate-induced production risk. Dummy = 1 if farmer. 0.71. 0.46 ..... cation exchange capacity for holding nutrients against leaching loss.

  5. Technology Insertion and Management: Options for the Canadian Forces

    Science.gov (United States)

    2010-01-01

    Technology Insertion and Management : Options for the Canadian Forces Mike Stocker Defence Economics Team Defence R&D Canada... Management Options for the Canadian Forces Mike Stocker Defence Economics Team The reported results, their interpretation, and any...semble indiquer qu’un changement de paradigme est en cours dans la façon dont les militaires élaborent et emploient la technologie à utiliser avec leurs

  6. Option pricing with COS method on Graphics Processing Units

    NARCIS (Netherlands)

    B. Zhang (Bo); C.W. Oosterlee (Cornelis)

    2009-01-01

    htmlabstractIn this paper, acceleration on the GPU for option pricing by the COS method is demonstrated. In particular, both European and Bermudan options will be discussed in detail. For Bermudan options, we consider both the Black-Scholes model and Levy processes of infinite activity. Moreover,

  7. Continuously monitored barrier options under Markov processes

    NARCIS (Netherlands)

    Mijatović, A.; Pistorius, M.

    2011-01-01

    In this paper, we present an algorithm for pricing barrier options in one-dimensional Markov models. The approach rests on the construction of an approximating continuous-time Markov chain that closely follows the dynamics of the given Markov model. We illustrate the method by implementing it for a

  8. Option Pricing with Time-changed Lévy Processes

    DEFF Research Database (Denmark)

    Klingler, Sven; Kim, Young Shin; Rachev, Svetlozar T.

    2013-01-01

    In this article, we introduce two new six-parameter processes based on time-changing tempered stable distributions and develop an option pricing model based on these processes. This model provides a good fit to observed option prices. To demonstrate the advantages of the new processes, we conduct...

  9. Linkage options between unit process to enhance proliferation resistance of pyroprocessing

    International Nuclear Information System (INIS)

    Ahn, Seong-Kyu; Seo, Chung-Seok; Kwon, Eun-ha; Kim, Ho-Dong

    2015-01-01

    Highlights: • The possible ways to link between unit steps of pyroprocessing were discussed. • These linkage options affect the safeguards and proliferation resistance aspects. • Chance for representative sample and less losses is essential for the head-end process. • Salt transfer with less hold-up and inventory measurability is key main process. • This study is aimed at a further investigation with process technical aspects. - Abstract: Pyroprocessing technology has been actively developed at KAERI as one of the options to address the national spent fuel management issue. As much as the unit process development itself, the linkage method between each unit process is also of importance. There may be different linkage options between a set of two process units, or different options caused by different technologies for one of two unit processes connected to each other. The linkage method may affect the loss of nuclear materials and distribution of fission products, which are essential from the safeguards and proliferation resistance points of view. In this study, different technology options for some of the major process steps and possible linkage options were identified, and aspects of their proliferation resistance including the impact on the safeguards are discussed. Several options for decladding and feeding to electro-reduction, dross and the residual salt treatment of reduced materials as well as feeding to electro-refining, and salt transfer from electro-refining to electro-winning were identified and their technical and proliferation resistance aspects were analyzed. This study does not conclude any ranking of each option or suggest which option is the best. It is important to note that the objectives to review the process and linkage options are to give the basic characteristics and technical information related to safeguards measures and proliferation resistance and to suggest a conceptual idea for certain options to investigate further and

  10. Technological substitution options for controlling greenhouse gas emissions

    International Nuclear Information System (INIS)

    Barbier, E.B.; Burgess, J.C.; Pearce, D.W.

    1991-01-01

    This chapter is concerned with technological options for greenhouse gas substitution. The authors interpret the term substitution to exclude energy conservation/efficiency measures, investments in afforestation (sinks), and greenhouse gas removal or abatement technologies. Their working definition of greenhouse gas substitution includes (1) replacement technologies, for example, substituting a greenhouse gas technology with a nongreenhouse gas technology; and (2) reduction technologies, for example, substituting a greenhouse gas technology with an alternative technology that reduces greenhouse gas emissions. Essentially, replacement technologies involve 100 percent reduction in CO 2 ; reduction technologies involve a partial reduction in CO 2 . Of the man-made sources of greenhouse gases, energy is the most important and is expected to contribute to at least half of the global warming effect in the near future. The majority of this impact is from fossil fuel combustion as a source of carbon dioxide (CO 2 ), although fossil fuels also contribute significantly to methane (CH 4 ), to nitrous oxide (N 2 O), and to low-level ozone (O 3 ) through production of various nitrogen gases (NO x ) and carbon monoxide (CO). This study analyzes the available greenhouse gas substitutions and their costs. The authors concentrate particularly on substitutions for fossil-fuel combustion and CFC production and consumption. They conclude by summarizing the potential for greenhouse gas substitution, the cost-effectiveness of the various options and the design of incentives for substitution

  11. Technologies options for acid-rain control. Book chapter

    International Nuclear Information System (INIS)

    Princiotta, F.T.

    1992-01-01

    The report discusses acid rain control options available to the electric utility industry. They include coal switching, flue gas desulfurization, and such emerging lower cost technologies as Limestone Injection Multistage Burners (LIMB) and Advanced Silicate (ADVACATE), both developed by EPA, selective use of gas to reduce nitrogen oxides (NOx) and sulfur dioxide (SO2) in coal-fired boilers, and the use of Integrated Coal Gasification Combined Cycle (IGCC) technology

  12. Technology or Process First?

    DEFF Research Database (Denmark)

    Siurdyban, Artur Henryk; Svejvig, Per; Møller, Charles

    between them using strategic alignment, Enterprise Systems and Business Process Management theories. We argue that the insights from these cases can lead to a better alignment between process and technology. Implications for practice include the direction towards a closer integration of process......Enterprise Systems Management (ESM) and Business Pro- cess Management (BPM), although highly correlated, have evolved as alternative and mutually exclusive approaches to corporate infrastruc- ture. As a result, companies struggle to nd the right balance between technology and process factors...... in infrastructure implementation projects. The purpose of this paper is articulate a need and a direction to medi- ate between the process-driven and the technology-driven approaches. Using a cross-case analysis, we gain insight into two examples of sys- tems and process implementation. We highlight the dierences...

  13. Desalination processes and technologies

    International Nuclear Information System (INIS)

    Furukawa, D.H.

    1996-01-01

    Reasons of the development of desalination processes, the modern desalination technologies, such as multi-stage flash evaporation, multi-effect distillation, reverse osmosis, and the prospects of using nuclear power for desalination purposes are discussed. 9 refs

  14. U.S. Linear Collider Technology Options Study

    International Nuclear Information System (INIS)

    Bagger, J.

    2006-01-01

    This study was carried out at the request of the United States Linear Collider Steering Group (USLCSG). The establishment of such a body was recommended by the HEPAP Subpanel on Long Range Planning [1]. The USLCSG is led by an Executive Committee, chaired by Jonathan Dorfan of SLAC, and consisting currently of the members shown in Table 1.1.1.1. Three subcommittees report to the Executive Committee: an Accelerator Subcommittee, a Physics/Detector Subcommittee, and an International Aggairs Subcommittee. While the functions of the Steering Group are expected to evolve with time, the initial charge includes the following items: (1) Provide an evaluation of options for building the linear collider involving factors such as scientific requirements, technical feasibility, risk, cost, initial facility parameters, upgradeability of alternate technologies, and the implications of different sites; and (2) Prepare the elements of a U.S. bid to host the linear collider. To address these items in its charge, the USLCSG Executive Committee asked the Accelerator Subcommittee to carry out an evaluation of two options for a US-sited linear collider. The two options were to be based on the normal conducting X-band RF technology developed by the GLC/NLC collaboration [ZDR, NLC01], [TRC, Chapter 3], and the superconducting L-band RF technology developed by the TESLA collaboration [TDR]. The physics design requirements which both technical options must meet were established [2] by the Physics and Detector Subcommittee of the USLCSG

  15. Technologies for Optical Processing

    DEFF Research Database (Denmark)

    Stubkjær, Kristian

    2008-01-01

    The article consists of a Powerpoint presentation on technologies for optical processing. The paper concludes that the nonlinear elements based on SOA, fibers and waveguide structures have capabilities of simple processing at data rates of 100-600 Gb/s. Switching powers comparable to electronics...

  16. Public attitudes toward political and technological options for biofuels

    International Nuclear Information System (INIS)

    Delshad, Ashlie B.; Raymond, Leigh; Sawicki, Vanessa; Wegener, Duane T.

    2010-01-01

    This paper explores detailed public attitudes regarding the expanding range of biofuels technologies and policy options. Subjects from 34 in-depth focus groups in central Indiana were fairly knowledgeable about biofuels technologies, but uninformed about biofuels policies despite being from a state where biofuels are a salient political issue. A narrow majority was supportive of biofuels in general, but expressed greater enthusiasm about 'second generation' biofuels. Subject beliefs about biofuels' economic and environmental impacts were most important in shaping these opinions, rather than concerns about energy independence or other issues. In terms of policy options, subjects were most supportive of an alternative fuels standard and least supportive of a fixed subsidy and a cap and trade policy. In contrast to arguments about technologies, participants primarily framed their attitudes toward policies in terms of fairness. Although discussion did not substantially change aggregate preferences for most policies, it did increase support significantly for at least one policy proposal-a variable subsidy for ethanol. It is particularly noteworthy that subjects generally did not support the most common biofuel technology-corn-based ethanol-or the most prominent biofuels policy option-the fixed subsidy-despite residing in a state hosting a strong corn industry and staunch political advocates for both positions.

  17. Surface technologies 2006-Alternative energies and policy options

    International Nuclear Information System (INIS)

    Rose, Lars

    2007-01-01

    Surfaces are the immediate contact between anything in our world. Literally, every industry utilizes coatings and surface modifications in order to create surfaces tailored to specific needs, protect underlying substrates, or modify their behavior. Surface and coating technologies are essential to a large variety of different industrial sectors, including transportation, manufacturing, food and biomedical engineering, energy, resources, and materials science and technology. The present paper explains the limitations for alternative energy technologies, with a focus on fuel cell technology development and the alternative energy sector, based on the outcomes of presentations and facilitated discussion groups during a Canadian national workshop series. Options for technological improvements of alternative energy systems are presented in combination with national and international policy choices, which could positively influence research and development in the alternative energy sector

  18. Processing education options await in Las Vegas

    Science.gov (United States)

    The 2017 IFT annual event promises to be both exciting and educational for those who wish to learn more about food processing. Compared with last year's annual event, this year has significantly more scientific sessions focused on food processing, and this column will provide a brief overview of se...

  19. Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

  20. Gram-Charlier Processes and Applications to Option Pricing

    Directory of Open Access Journals (Sweden)

    Jean-Pierre Chateau

    2017-01-01

    Full Text Available A Gram-Charlier distribution has a density that is a polynomial times a normal density. For option pricing this retains the tractability of the normal distribution while allowing nonzero skewness and excess kurtosis. Properties of the Gram-Charlier distributions are derived, leading to the definition of a process with independent Gram-Charlier increments, as well as formulas for option prices and their sensitivities. A procedure for simulating Gram-Charlier distributions and processes is given. Numerical illustrations show the effect of skewness and kurtosis on option prices.

  1. VLSI signal processing technology

    CERN Document Server

    Swartzlander, Earl

    1994-01-01

    This book is the first in a set of forthcoming books focussed on state-of-the-art development in the VLSI Signal Processing area. It is a response to the tremendous research activities taking place in that field. These activities have been driven by two factors: the dramatic increase in demand for high speed signal processing, especially in consumer elec­ tronics, and the evolving microelectronic technologies. The available technology has always been one of the main factors in determining al­ gorithms, architectures, and design strategies to be followed. With every new technology, signal processing systems go through many changes in concepts, design methods, and implementation. The goal of this book is to introduce the reader to the main features of VLSI Signal Processing and the ongoing developments in this area. The focus of this book is on: • Current developments in Digital Signal Processing (DSP) pro­ cessors and architectures - several examples and case studies of existing DSP chips are discussed in...

  2. Comparison of Color and Fabric Presentation Options in the Design Process

    OpenAIRE

    Jackson, Reneé Susan

    2000-01-01

    The purpose of this research was to assess the current (manual) and future (automated) presentation options for fabric and color in the design process. Current and future presentation options were assessed for viability and identification of relationships between reported sufficiency levels and recommended use responses. This exploration was used to identify new and future technologies for presentation of fabric and color that could potentially aid in increasing product manufacturing competit...

  3. Technological options for management of hazardous wastes from US Department of Energy facilities

    Energy Technology Data Exchange (ETDEWEB)

    Chiu, S.; Newsom, D.; Barisas, S.; Humphrey, J.; Fradkin, L.; Surles, T.

    1982-08-01

    This report provides comprehensive information on the technological options for management of hazardous wastes generated at facilities owned or operated by the US Department of Energy (DOE). These facilities annually generate a large quantity of wastes that could be deemed hazardous under the Resource Conservation and Recovery Act (RCRA). Included in these wastes are liquids or solids containing polychlorinated biphenyls, pesticides, heavy metals, waste oils, spent solvents, acids, bases, carcinogens, and numerous other pollutants. Some of these wastes consist of nonnuclear hazardous chemicals; others are mixed wastes containing radioactive materials and hazardous chemicals. Nearly 20 unit processes and disposal methods are presented in this report. They were selected on the basis of their proven utility in waste management and potential applicability at DOE sites. These technological options fall into five categories: physical processes, chemical processes, waste exchange, fixation, and ultimate disposal. The options can be employed for either resource recovery, waste detoxification, volume reduction, or perpetual storage. Detailed descriptions of each technological option are presented, including information on process performance, cost, energy and environmental considerations, waste management of applications, and potential applications at DOE sites. 131 references, 25 figures, 23 tables.

  4. Technological options for management of hazardous wastes from US Department of Energy facilities

    International Nuclear Information System (INIS)

    Chiu, S.; Newsom, D.; Barisas, S.; Humphrey, J.; Fradkin, L.; Surles, T.

    1982-08-01

    This report provides comprehensive information on the technological options for management of hazardous wastes generated at facilities owned or operated by the US Department of Energy (DOE). These facilities annually generate a large quantity of wastes that could be deemed hazardous under the Resource Conservation and Recovery Act (RCRA). Included in these wastes are liquids or solids containing polychlorinated biphenyls, pesticides, heavy metals, waste oils, spent solvents, acids, bases, carcinogens, and numerous other pollutants. Some of these wastes consist of nonnuclear hazardous chemicals; others are mixed wastes containing radioactive materials and hazardous chemicals. Nearly 20 unit processes and disposal methods are presented in this report. They were selected on the basis of their proven utility in waste management and potential applicability at DOE sites. These technological options fall into five categories: physical processes, chemical processes, waste exchange, fixation, and ultimate disposal. The options can be employed for either resource recovery, waste detoxification, volume reduction, or perpetual storage. Detailed descriptions of each technological option are presented, including information on process performance, cost, energy and environmental considerations, waste management of applications, and potential applications at DOE sites. 131 references, 25 figures, 23 tables

  5. Optimal stopping and perpetual options for Lévy processes

    OpenAIRE

    Ernesto Mordecki

    2002-01-01

    Consider a model of a financial market with a stock driven by a Lévy process and constant interest rate. A closed formula for prices of perpetual American call options in terms of the overall supremum of the Lévy process, and a corresponding closed formula for perpetual American put options involving the infimum of the after-mentioned process are obtained. As a direct application of the previous results, a Black-Scholes type formula is given. Also as a consequence, simple explicit formulas fo...

  6. Engineering Options Assessment Report. Nitrate Salt Waste Stream Processing

    Energy Technology Data Exchange (ETDEWEB)

    Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-13

    This report examines and assesses the available systems and facilities considered for carrying out remediation activities on remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The assessment includes a review of the waste streams consisting of 60 RNS, 29 above-ground UNS, and 79 candidate below-ground UNS containers that may need remediation. The waste stream characteristics were examined along with the proposed treatment options identified in the Options Assessment Report . Two primary approaches were identified in the five candidate treatment options discussed in the Options Assessment Report: zeolite blending and cementation. Systems that could be used at LANL were examined for housing processing operations to remediate the RNS and UNS containers and for their viability to provide repackaging support for remaining LANL legacy waste.

  7. Engineering Options Assessment Report: Nitrate Salt Waste Stream Processing

    Energy Technology Data Exchange (ETDEWEB)

    Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-18

    This report examines and assesses the available systems and facilities considered for carrying out remediation activities on remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The assessment includes a review of the waste streams consisting of 60 RNS, 29 aboveground UNS, and 79 candidate belowground UNS containers that may need remediation. The waste stream characteristics were examined along with the proposed treatment options identified in the Options Assessment Report . Two primary approaches were identified in the five candidate treatment options discussed in the Options Assessment Report: zeolite blending and cementation. Systems that could be used at LANL were examined for housing processing operations to remediate the RNS and UNS containers and for their viability to provide repackaging support for remaining LANL legacy waste.

  8. Option Pricing with Stochastic Volatility and Jump Diffusion Processes

    Directory of Open Access Journals (Sweden)

    Radu Lupu

    2006-05-01

    Full Text Available Option pricing by the use of Black Scholes Merton (BSM model is based on the assumption that asset prices have a lognormal distribution. In spite of the use of these models on a large scale, both by practioners and academics, the assumption of lognormality is rejected by the history of returns. The objective of this article is to present the methods that developed after the Black Scholes Merton environment and deals with the option pricing model adjustment to the empirical properties of asset returns. The main models that appeared after BSM allowed for special changes of the returns that materialized in jump-diffusion and stochastic volatility processes. The article presents the foundations of risk neutral options evaluation and the empirical evidence that fed the amendment of the lognormal assumption in the first part and shows the evaluation procedure under the assumption of stock prices following the jump-diffusion process and the stochastic volatility process.

  9. Option Pricing with Stochastic Volatility and Jump Diffusion Processes

    Directory of Open Access Journals (Sweden)

    Radu Lupu

    2006-03-01

    Full Text Available Option pricing by the use of Black Scholes Merton (BSM model is based on the assumption that asset prices have a lognormal distribution. In spite of the use of these models on a large scale, both by practioners and academics, the assumption of lognormality is rejected by the history of returns. The objective of this article is to present the methods that developed after the Black Scholes Merton environment and deals with the option pricing model adjustment to the empirical properties of asset returns. The main models that appeared after BSM allowed for special changes of the returns that materialized in jump-diffusion and stochastic volatility processes. The article presents the foundations of risk neutral options evaluation and the empirical evidence that fed the amendment of the lognormal assumption in the first part and shows the evaluation procedure under the assumption of stock prices following the jump-diffusion process and the stochastic volatility process.

  10. Perspectives on Multienzyme Process Technology

    DEFF Research Database (Denmark)

    Santacoloma, Paloma A.; Woodley, John M.

    2014-01-01

    There is little doubt that chemical processing of the future will involve an increasing number of biocatalytic processes using more than one enzyme. There are good reasons for developing such innovative biocatalytic processes and interesting new biocatalyst and process options will be introduced....

  11. A facilitated process towards finding options for improved livestock ...

    African Journals Online (AJOL)

    A participatory multi-stakeholder process of finding options for improving livestock production in the severely degraded communal grazing area of Sterkspruit in South Africa was conducted. Interviews were conducted with individual livestock keepers from two sites to gather data on their demographic characteristics, ...

  12. Warranty of Misinforming as an Option in Product Utilization Process

    Directory of Open Access Journals (Sweden)

    Dimitar Grozdanov Christozov

    2016-05-01

    Full Text Available The following definition of “option” is given in Wikipedia - “In finance, an option is a contract, which gives the buyer (the owner or holder the right, but not the obligation, to buy or sell an underlying asset or instrument at a specified strike price on or before a specified date, depending on the form of the option” (“Option,” n.d.. Option as a risk management (mitigation tool is broadly used in finance and trade. At the same time, it introduces asymmetry in the sense that, probabilistically, it limits the level of losses (e.g., the price of the option and allows for unlimited gains. In the market of sophisticated devices (as smart phones, tablets, etc., where technologies are rapidly advancing, customers usually do not have the experience to use all features of the device at the time of the purchase. Due to the lack of appropriate expertise, the risk of misinforming, leading to not purchasing the “right” device is high, but given enough time to learn the capabilities of the device and map these to the needs and tasks that device will be used for, could provide the client with substantial long term benefits. Warranty of misinforming is a mechanism that provides the client with the opportunity to explore the device and master its features under limited risk of financial losses. Thus, the warranty of misinforming could be considered as an option - the custom-ers buy it (at a fixed cost and may gain (theoretically unlimited benefit by realizing (within the terms of the warranty that the device can be used to solve a variety of problems not envisaged at the time of purchase. In this study we present the idea of treating the warranty of misinforming as an option in finances and provide examples to illustrate our viewpoint.

  13. Efficient Option Pricing under Levy Processes, with CVA and FVA

    Directory of Open Access Journals (Sweden)

    Jimmy eLaw

    2015-07-01

    Full Text Available We generalize the Piterbarg (2010 model to include 1 bilateral default risk as in Burgard and Kjaer (2012, and 2 jumps in the dynamics of the underlying asset using general classes of L'evy processes of exponential type. We develop an efficient explicit-implicit scheme for European options and barrier options taking CVA-FVA into account. We highlight the importance of this work in the context of trading, pricing and management a derivative portfolio given the trajectory of regulations.

  14. Integrating energy and environmental goals. Investment needs and technology options

    International Nuclear Information System (INIS)

    2004-04-01

    , since their shares of global energy demand and emissions are expected to grow rapidly. Over the next thirty years, developing countries are expected to account for 70% of the growth in global energy demand and for two-thirds of the growth in global emissions. Section six looks at some of the challenges regarding investment and energy access. Security of energy supply is an important component in the planning of future technology options, because long-term security calls for a balance between energy sources and technologies. Governments have a role to play in tipping this balance, and this role is examined in section seven. A final section examines the uncertainties and costs of various policy initiatives over the long term

  15. Low Carbon Technology Options for the Natural Gas ...

    Science.gov (United States)

    The ultimate goal of this task is to perform environmental and economic analysis of natural gas based power production technologies (different routes) to investigate and evaluate strategies for reducing emissions from the power sector. It is a broad research area. Initially, the research will be focused on the preliminary analyses of hydrogen fuel based power production technologies utilizing hydrogen fuel in a large size, heavy-duty gas turbines in integrated reformer combined cycle (IRCC) and integrated gasification combined cycle (IGCC) for electric power generation. The research will be expanded step-by-step to include other advanced (e.g., Net Power, a potentially transformative technology utilizing a high efficiency CO2 conversion cycle (Allam cycle), and chemical looping etc.) pre-combustion and post-combustion technologies applied to natural gas, other fossil fuels (coal and heavy oil) and biomass/biofuel based on findings. Screening analysis is already under development and data for the analysis is being processed. The immediate action on this task include preliminary economic and environmental analysis of power production technologies applied to natural gas. Data for catalytic reforming technology to produce hydrogen from natural gas is being collected and compiled on Microsoft Excel. The model will be expanded for exploring and comparing various technologies scenarios to meet our goal. The primary focus of this study is to: 1) understand the chemic

  16. Options for gas-to-liquids technology in Alaska

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, E.P.

    1999-12-01

    The purpose of this work was to assess the effect of applying new technology to the economics of a proposed natural gas-to-liquids (GTL) plant, to evaluate the potential of a slower-paced, staged deployment of GTL technology, and to evaluate the effect of GTL placement of economics. Five scenarios were economically evaluated and compared: a no-major-gas-sales scenario, a gas-pipeline/LNG scenario, a fast-paced GTL development scenario, a slow-paced GTL development scenario, and a scenario which places the GTL plant in lower Alaska, instead of on the North Slope. Evaluations were completed using an after-tax discounted cash flow analysis. Results indicate that the slow-paced GTL scenario is the only one with a rate of return greater than 10%. The slow-paced GTL development would allow cost saving on subsequent expansions. These assumed savings, along with the lowering of the transportation tariff, combine to distinguish this option for marketing the North Slope gas from the other scenarios. Critical variables that need further consideration include the GTL plant cost, the GTL product premium, and operating and maintenance costs.

  17. Options for Gas-to-Liquids Technology in Alaska

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Eric Partridge

    1999-10-01

    The purposes of this work was to assess the effect of applying new technology to the economics of a proposed natural gas-to-liquids (GTL) plant, to evaluate the potential of a slower-paced, staged deployment of GTL technology, and to evaluate the effect of GTL placement of economics. Five scenarios were economically evaluated and compared: a no-major-gas-sales scenario, a gas-pipeline/LNG scenario, a fast-paced GTL development scenario, a slow-paced GTL development scenario, and a scenario which places the GTL plant in lower Alaska, instead of on the North Slope. Evaluations were completed using an after-tax discounted cash flow analysis. Results indicate that the slow-paced GTL scenario is the only one with a rate of return greater than 10 percent. The slow-paced GTL development would allow cost saving on subsequent expansions. These assumed savings, along with the lowering of the transportation tariff, combine to distinquish this option for marketing the North Slope gas from the other scenarios. Critical variables that need further consideration include the GTL plant cost, the GTL product premium, and operating and maintenance costs.

  18. Process technologies for water desalination

    International Nuclear Information System (INIS)

    Ramilo, Lucia B.; Gomez de Soler, Susana M.; Coppari, Norberto R.

    2003-01-01

    The use of the nuclear energy for simultaneous electricity and potable water production is an attractive, technically feasible, and safe alternative to fossil energy options. In Argentina the nuclear desalination option is being studied together with the alternative uses of the innovative advanced Argentinean CAREM reactor, in the research contract CNEA - IAEA to evaluate projects of nuclear desalination. The objective and scope of this work is to know the advantages and disadvantages of each desalination technology, distinctive characteristics of each of them, that make them adapt better to different uses and outline conditions and analysis of related antecedents of its use in the world. In this report a summarized description of those technologies is included by way of introduction, so as to highlight the main advantages and disadvantages of each of them. The improvements and innovations found in the last years for the different technologies are also included. (author)

  19. Particle processing technology

    Science.gov (United States)

    Yoshio, Sakka

    2014-02-01

    In recent years, there has been strong demand for the development of novel devices and equipment that support advanced industries including IT/semiconductors, the environment, energy and aerospace along with the achievement of higher efficiency and reduced environmental impact. Many studies have been conducted on the fabrication of innovative inorganic materials with novel individual properties and/or multifunctional properties including electrical, dielectric, thermal, optical, chemical and mechanical properties through the development of particle processing. The fundamental technologies that are key to realizing such materials are (i) the synthesis of nanoparticles with uniform composition and controlled crystallite size, (ii) the arrangement/assembly and controlled dispersion of nanoparticles with controlled particle size, (iii) the precise structural control at all levels from micrometer to nanometer order and (iv) the nanostructural design based on theoretical/experimental studies of the correlation between the local structure and the functions of interest. In particular, it is now understood that the application of an external stimulus, such as magnetic energy, electrical energy and/or stress, to a reaction field is effective in realizing advanced particle processing [1-3]. This special issue comprises 12 papers including three review papers. Among them, seven papers are concerned with phosphor particles, such as silicon, metals, Si3N4-related nitrides, rare-earth oxides, garnet oxides, rare-earth sulfur oxides and rare-earth hydroxides. In these papers, the effects of particle size, morphology, dispersion, surface states, dopant concentration and other factors on the optical properties of phosphor particles and their applications are discussed. These nanoparticles are classified as zero-dimensional materials. Carbon nanotubes (CNT) and graphene are well-known one-dimensional (1D) and two-dimensional (2D) materials, respectively. This special issue also

  20. Overview of spent fuel management options: Technology and cost

    International Nuclear Information System (INIS)

    Beeman, G.H.

    1986-01-01

    The options for spent fuel management discussed in this paper. There are several spent fuel management options available to utilities beyond the traditional options of reracking and transshipment. Two different dry storage options have been licensed by NRC and it appears that NRC will issue a license amendment to allow for the storage of consolidated spent fuel in the very near future. The use of either of these spent fuel management options is highly dependent upon the individual requirements of the utility. There are several factors that must be considered when choosing a specific fuel management option. Either of these spent fuel management options, dry storage or rod consolidation, is capable of meeting the needs of utilities for additional spent fuel storage until DOE begins accepting spent fuel for final disposal in 1998

  1. Defaultable Game Options in a Hazard Process Model

    Directory of Open Access Journals (Sweden)

    Tomasz R. Bielecki

    2009-01-01

    Full Text Available The valuation and hedging of defaultable game options is studied in a hazard process model of credit risk. A convenient pricing formula with respect to a reference filteration is derived. A connection of arbitrage prices with a suitable notion of hedging is obtained. The main result shows that the arbitrage prices are the minimal superhedging prices with sigma martingale cost under a risk neutral measure.

  2. Decision-making model of generation technology under uncertainty based on real option theory

    International Nuclear Information System (INIS)

    Ming, Zeng; Ping, Zhang; Shunkun, Yu; Ge, Zhang

    2016-01-01

    Highlights: • A decision-making model of generation technology investment is proposed. • The irreversible investment concept and real option theory is introduced. • Practical data was used to prove the validity of the model. • Impact of electricity and fuel price fluctuation on investment was analyzed. - Abstract: The introduction of market competition and the increased uncertainty factors makes the generators have to decide not only on whether to invest generation capacity or not but also on what kind of generation technology to choose. In this paper, a decision-making model of generation technology investment is proposed. The irreversible investment concept and real option theory is introduced as the fundamental of the model. In order to explain the decision-making process of generator’s investment, the decision-making optimization model was built considering two generation technologies, i.e., the heat-only system and the combined heat and power generation. Also, we discussed the theory deducing process, which explained how to eliminate the overrated economic potential caused by risk hazard, based on economic evaluation of both generation technologies. Finally, practical data from electricity market of Inner Mongolia was used to prove the validity of the model and the impact of uncertainties of electricity and fuel price fluctuation on investment was analyzed according to the simulated results.

  3. The role of nuclear power in the option zero emission technologies for fossil fuels

    International Nuclear Information System (INIS)

    Corak, Z.

    2006-01-01

    The energy sector is one of the main sources of greenhouse gas (GHG) emissions particularly carbon dioxide (CO2) increasing concerns due to their potential risk to induce global warming and climate change. The Parties having signed the Kyoto Protocol in December 1997, committed to decrease their GHG emissions. The Protocol states that countries shall undertake promotion, research, development and increased use of new and renewable forms of energy, of carbon dioxide sequestration technologies and of advanced and innovative environmentally sound technologies. The one significant option that is not specifically mentioned is nuclear energy which is essentially carbon-free. There are a number of technical options that could help reducing, or at least slowing the increase of, GHG emissions from the energy sector. The list of options includes: improving the efficiency of energy conversion and end-use processes; shifting to less carbon intensive energy sources (e.g. shifting from coal to natural gas); developing carbon-free or low-carbon energy sources; and carbon sequestration (e.g. planting forests or capturing and storing carbon dioxide). It must be pointed out that nuclear power is one of the few options that are currently available on the market, competitive in a number of countries, especially if global costs to society of alternative options are considered; practically carbon-free; and sustainable at large-scale deployment. The nuclear power could play significant role in alleviating the risk of global climate change. The main objective of the article is to present sequestration options, their cost evaluation as well as comparation with alternative possibilities of nuclear energy production. (author)

  4. Cloud Computing: A Free Technology Option to Promote Collaborative Learning

    Science.gov (United States)

    Siegle, Del

    2010-01-01

    In a time of budget cuts and limited funding, purchasing and installing the latest software on classroom computers can be prohibitive for schools. Many educators are unaware that a variety of free software options exist, and some of them do not actually require installing software on the user's computer. One such option is cloud computing. This…

  5. Evaluating the impacts of energy supply technology options

    International Nuclear Information System (INIS)

    Peachey, B.R.

    2009-01-01

    The newly formed Chemical Institute of Canada (CIC)/Canadian Society for Chemical Engineering (CSChE) Energy Subject Division is working to develop a methodology for assessing and communicating to governments, regulators and the public the relative merits of different technologies for meeting energy demand requirements or reducing energy consumption. The focus is on developing a process that considers a broader range of issues than basic economics, or greenhouse gas (GHG) emissions. The 12 assessment criteria proposed would address five major areas of concerns including: a) how well assumptions have been tested against the scientific method over the life cycle of an energy development, b) impacts on the availability of the basic requirements for life, c) maintaining the quality of human life, d) maintaining the quality of the local environment (air, land and water), in the area where a specific technology is used, and e) considers the potential global impacts of GHG emissions. (author)

  6. The Right Tools for the Job--Technology Options for Adult Online Learning and Collaboration

    Science.gov (United States)

    Regional Educational Laboratory, 2014

    2014-01-01

    Many options exist for using technology as a tool for adult learning, and each day, it becomes easier to share information online than it ever has been. Online learning technology has grown from one-sided communications to numerous options for audience engagement and interactivity. This guide introduces a variety of tools, online platforms, and…

  7. CRADA Payment Options | NCI Technology Transfer Center | TTC

    Science.gov (United States)

    NCI TTC CRADA PAYMENT OPTIONS: Electronic Payments by Wire Transfer via Fedwire, Mail a check to the Institute or Center, or Automated Clearing House (ACH)/Electronic Funds Transfer (ETF) payments via Pay.gov (NCI ONLY).

  8. Fundamentals of semiconductor processing technology

    CERN Document Server

    El-Kareh, Badih

    1995-01-01

    The drive toward new semiconductor technologies is intricately related to market demands for cheaper, smaller, faster, and more reliable circuits with lower power consumption. The development of new processing tools and technologies is aimed at optimizing one or more of these requirements. This goal can, however, only be achieved by a concerted effort between scientists, engineers, technicians, and operators in research, development, and manufac­ turing. It is therefore important that experts in specific disciplines, such as device and circuit design, understand the principle, capabil­ ities, and limitations of tools and processing technologies. It is also important that those working on specific unit processes, such as lithography or hot processes, be familiar with other unit processes used to manufacture the product. Several excellent books have been published on the subject of process technologies. These texts, however, cover subjects in too much detail, or do not cover topics important to modem tech­ n...

  9. First Passage Time for Tempered Stable Process and Its Application to Perpetual American Option and Barrier Option Pricing

    OpenAIRE

    Kim, Young Shin

    2018-01-01

    In this paper, we will discuss an approximation of the characteristic function of the first passage time for a Levy process using the martingale approach. The characteristic function of the first passage time of the tempered stable process is provided explicitly or by an indirect numerical method. This will be applied to the perpetual American option pricing and the barrier option pricing. Numerical illustrations are provided for the calibrated parameters using the market call and put prices.

  10. Ionizing Radiation Processing Technology

    International Nuclear Information System (INIS)

    Rida Tajau; Kamarudin Hashim; Jamaliah Sharif; Ratnam, C.T.; Keong, C.C.

    2017-01-01

    This book completely brief on the basic concept and theory of ionizing radiation in polymers material processing. Besides of that the basic concept of polymerization addition, cross-linking and radiation degradation also highlighted in this informative book. All of the information is from scientific writing based on comprehensive scientific research in polymerization industry which using the radiation ionizing. It is very useful to other researcher whose study in Nuclear Sciencea and Science of Chemical and Material to use this book as a guideline for them in future scientific esearch.

  11. Low cost options for tissue culture technology in developing countries. Proceedings of a technical meeting

    International Nuclear Information System (INIS)

    2004-02-01

    Tissue culture technology is used for the production of doubled haploids, cryopreservation, propagating new plant varieties, conserving rare and endangered plants, difficult-to-propagate plants, and to produce secondary metabolites and transgenic plants. The production of high quality planting material of crop plants and fruit trees, propagated from vegetative parts, has created new opportunities in global trading, benefited growers, farmers, and nursery owners, and improved rural employment. However, there are still major opportunities to produce and distribute high quality planting material, e.g. crops like banana, date palm, cassava, pineapple, plantain, potato, sugarcane, sweet potato, yams, ornamentals, fruit and forest trees. The main advantage of tissue culture technology lies in the production of high quality and uniform planting material that can be multiplied on a year-round basis under disease-free conditions anywhere irrespective of the season and weather. However, the technology is capital, labor and energy intensive. Although, labor is cheap in many developing countries, the resources of trained personnel and equipment are often not readily available. In addition, energy, particularly electricity, and clean water are costly. The energy requirements for tissue culture technology depend on day temperature, day-length and relative humidity, and they have to be controlled during the process of propagation. Individual plant species also differ in their growth requirements. Hence, it is necessary to have low cost options for weaning, hardening of micropropagated plants and finally growing them in the field. This publication describes options for reducing costs to establish and operate tissue culture facilities and primarily focus on plant micropropagation. It includes papers on the basics of tissue culture technology, low cost options for the design of laboratories, use of culture media and containers, energy and labor saving, integration and adoption of

  12. A real options evaluation model for the diffusion prospects of new renewable power generation technologies

    International Nuclear Information System (INIS)

    Kumbaroglu, Guerkan; Demirel, Mustafa; Madlener, Reinhard

    2008-01-01

    This study presents a policy planning model that integrates learning curve information on renewable power generation technologies into a dynamic programming formulation featuring real options analysis. The model recursively evaluates a set of investment alternatives on a year-by-year basis, thereby taking into account that the flexibility to delay an irreversible investment expenditure can profoundly affect the diffusion prospects of renewable power generation technologies. Price uncertainty is introduced through stochastic processes for the average wholesale price of electricity and for input fuel prices. Demand for electricity is assumed to be increasingly price-sensitive, as the electricity market deregulation proceeds, reflecting new options of consumers to react to electricity price changes (such as time-of-use pricing, unbundled electricity services, and choice of supplier). The empirical analysis is based on data for the Turkish electricity supply industry. Apart from general implications for policy-making, it provides some interesting insights about the impact of uncertainty and technical change on the diffusion of various emerging renewable energy technologies. (author)

  13. 81 options. Technology for sustainable development; 81 mogelijkheden. Technologie voor duurzame ontwikkeling

    Energy Technology Data Exchange (ETDEWEB)

    Weterings, R.; Kuijper, J.; Smeets, E. [TNO Studiecentrum voor Technologie en Beleid TNO-STB, Apeldoorn (Netherlands); Annokee, G.J. [TNO Milieu, Energie en Procesinnovatie TNO-MEP, Apeldoorn (Netherlands); Minne, B. [Centraal Planbureau CPB, The Hague (Netherlands)

    1997-03-01

    An outline is given of the chances and threats of technological developments for the environment in the next 25 years. First, the most important technological supply-side developments were inventorized and assessed for their environmental relevance and in the light of three CPB-scenarios. From the results of the analysis it appears that their are many options to improve the environmental efficiency of products and processes. An important motive to develop environment-efficient technology is the price of energy. A higher price for energy will stimulate the development of energy efficient products and processes. Also the interest for dematerialization will increase while the processing of basic materials and the use of materials requires energy too. A second important motive is the demand for environment-efficient products. The market introduction of new environment-friendly products strongly depends on the quality consciousness (including the environmental quality) of the consumer. With respect to the environmental policy it can be concluded that technological innovation is important in the transfer of a decontamination-based policy to a prevention-based policy. 95 refs.

  14. Energy and the environment: Technology assessment and policy options

    International Nuclear Information System (INIS)

    Silveira, M.P.W.

    1990-01-01

    While the energy crisis of the 1970s stimulated technological innovation in developed countries, it often had the opposite effect in the third world. However, developing countries can be considered to have two types of energy systems: ''connected'' and ''disconnected''. The connected system is affected by changes in the price of commercial energy, but the disconnected system is usually rural and remote. Commercial forms of energy may be needed in the disconnected system, but they are largely unavailable. In some of the developing countries, new energy technologies have therefore been developed which adapt traditional technologies still existing in the disconnected sector. In this article some of the work of the United National Centre for Science and Technology for Development is described. Through its ATAS (Advance Technology Alert System) programme, international and regional workshops are held to discuss policy questions arising in regard to new technologies and developments. Workshops have been held in Moscow on new energy technologies in the industry subsystem (connected), in Guatemala City on new energy technologies and the disconnected system, and in Ottawa on new energy technologies, transportation and development. Initial assessments made by or through these workshops are outlined here. A fourth workshop will be held in June 1990 in Saarbrucken on energy technologies and climate change. (author). 3 figs

  15. Plasma technology in metallurgical processing

    Energy Technology Data Exchange (ETDEWEB)

    Haile, O.

    1995-12-31

    This literature work is mainly focusing on the mechanisms of plasma technology and telling about metallurgical processing, particularly iron and steelmaking as well as the advantage of the unique properties of plasma. The main advantages of plasma technology in metallurgical operations is to direct utilization of naturally available raw materials and fuels without costly upgrading andlor beneficiation, improved environmental impact, improve process control, significant amplification of reactor and process equipment utilization and increased efficiency of raw materials, energy and man power. This literature survey is based on the publication `plasma technology in metallurgical processing` presents a comprehensive account of the physical, electrical, and mechanical aspects of plasma production and practical processing. The applications of plasma technology in metallurgical processing are covered in depth with special emphasis on developments in promising early stages. Plasma technology of today is mature in the metallurgical process applications. A few dramatic improvements are expected in the near future this giving an impetus to the technologists for the long range planning. (18 refs.) (author)

  16. Small Technology--Big Impact. Practical Options for Development

    Science.gov (United States)

    Academy for Educational Development, 2009

    2009-01-01

    Technology has dramatically changed the world--now almost anyone can "move" at Internet-speed; people who were marginalized are able to find information on acquiring micro-loans to start businesses, and villages previously unconnected to the telecommunications grid now have affordable cell phone access. As technology becomes easier to…

  17. Radiation processing technology in Malaysia

    International Nuclear Information System (INIS)

    Khairul Zaman Hj Mohd Dahlan

    2004-01-01

    Radiation processing technology is widely used in industry to enhance efficiency and productivity, improve product quality and competitiveness. Efforts have been made by MINT to expand the application of radiation processing technology for modification of indigenous materials such as natural rubber and rubber based products, palm oil and palm oil based products and polysaccharide into new and high value added products. This paper described MINT experiences on developing products through R and D from the laboratory to the pilot plant stage and commercialization. The paper also explained some issues and challenges that MINT encountered in the process of commercialization of its R and D results. (author)

  18. The future of cybertherapy: improved options with advanced technologies.

    Science.gov (United States)

    Wiederhold, Brenda K; Wiederhold, Mark D

    2004-01-01

    Cybertherapy is a field that is growing rapidly due to today's technology and information boom. Virtual reality and advanced technologies have been used successfully to in a variety of healthcare issues, including treatment of anxiety disorders and phobias, treatment of eating and body dysmorphic disorders, neuropsychological assessment and rehabilitation and distraction during painful or unpleasant medical procedures. The novel applications of these technologies yield many advantages over traditional treatment modalities, and the disadvantages that accompanied the first trials of virtual reality are quickly being addressed and eliminated. Virtual reality peripherals such as data gloves, physiological monitoring and Internet worlds are swiftly demonstrating their usefulness in cybertherapy applications. Future directions for research include improvements of objective measures of efficacy such as fMRI and physiological monitoring devices, and investigations are being carried out to determine if virtual reality and advanced technologies can be used to treat a broader scope of disorders, including depression, schizophrenia, drug addiction, and autism.

  19. Africa's technology options for renewable energy production and distribution

    CSIR Research Space (South Africa)

    Amigun, B

    2011-12-01

    Full Text Available This chapter presents a critical appraisal of Africa's modern energy technologies for renewable energy. It highlights issues of scale and location-specific attributes. A critical review of different renewable energies is presented, the state...

  20. Natural Gas Based Electricity Production and Low Carbon Technology Options

    Science.gov (United States)

    Concerns regarding air quality, global climate change, and the national energy security impacts of the intensive use of fossil fuels and their environmental impacts in the power generation sector have raised interest in alternative low carbon electricity generation technology and...

  1. An exploration of options and functions of climate technology centres and networks. Discussion paper

    International Nuclear Information System (INIS)

    De Coninck, H.C.; Wuertenberger, L.; Cochran, J.; Cox, S.; Benioff, R.

    2010-11-01

    This paper responds to a request to UNEP from the UNFCCC Expert Group on Technology Transfer to examine operational modalities for climate technology centres and networks. The paper first discusses possible dimensions for the climate technology centre and network, and it reviews a number of existing networks and centres. It then distinguishes five options for the organizational structure and describes potential operational characteristics for each of these options. All options examined seek to build from existing climate and non-climate-related public and private technology centres, networks, and initiatives. Consistent with the UNFCCC negotiating text and draft technology decision, the paper evaluates potential implementation options and outcomes for each of the functions tentatively assigned to the climate technology centre and network, as well as selected functions of the technology executive committee. Approaches are offered for integrating delivery of these functions through coordinated programmes, and hypothetical examples are given to explain how the technology mechanism might add value in practice. The options presented in this paper are not an exhaustive treatment of potential structures or implementation approaches, and other approaches can be considered.

  2. MisTec - A software application for supporting space exploration scenario options and technology development analysis and planning

    Science.gov (United States)

    Horsham, Gary A. P.

    1992-01-01

    This structure and composition of a new, emerging software application, which models and analyzes space exploration scenario options for feasibility based on technology development projections is presented. The software application consists of four main components: a scenario generator for designing and inputting scenario options and constraints; a processor which performs algorithmic coupling and options analyses of mission activity requirements and technology capabilities; a results display which graphically and textually shows coupling and options analysis results; and a data/knowledge base which contains information on a variety of mission activities and (power and propulsion) technology system capabilities. The general long-range study process used by NASA to support recent studies is briefly introduced to provide the primary basis for comparison for discussing the potential advantages to be gained from developing and applying this kind of application. A hypothetical example of a scenario option to facilitate the best conceptual understanding of what the application is, how it works, or the operating methodology, and when it might be applied is presented.

  3. MisTec: A software application for supporting space exploration scenario options and technology development analysis and planning

    Science.gov (United States)

    Horsham, Gary A. P.

    1991-01-01

    The structure and composition of a new, emerging software application, which models and analyzes space exploration scenario options for feasibility based on technology development projections is presented. The software application consists of four main components: a scenario generator for designing and inputting scenario options and constraints; a processor which performs algorithmic coupling and options analyses of mission activity requirements and technology capabilities; a results display which graphically and textually shows coupling and options analysis results; and a data/knowledge base which contains information on a variety of mission activities and (power and propulsion) technology system capabilities. The general long-range study process used by NASA to support recent studies is briefly introduced to provide the primary basis for comparison for discussing the potential advantages to be gained from developing and applying this king of application. A hypothetical example of a scenario option to facilitate the best conceptual understanding of what the application is, how it works, or the operating methodology, and when it might be applied is presented.

  4. Energy and the European public opinion: options and technologies

    International Nuclear Information System (INIS)

    Poireau, M.; Rossetti Divaldalbero, D.; Huemer, M.

    2003-01-01

    What is the attitude of the Europeans concerning energy and energy technology? This is the question that the Department of Research (working with the Department of Energy and Transport) of the European Commission has attempted to answer with the launch of its 'Eurobarometer' survey to gauge European public opinion. Launched under the 'Science and Society' banner, one of the new priorities of the sixth framework research and technological development programme of the European Union, this 'Eurobarometer' is aimed at helping us to better understand the perceptions of the public in Europe vis-a-vis energy and to highlight questions to be discussed for the future of energy technology with regard to social acceptability. (authors)

  5. Low Carbon Technology Options for the Natural Gas Electricity Production

    Science.gov (United States)

    The ultimate goal of this task is to perform environmental and economic analysis of natural gas based power production technologies (different routes) to investigate and evaluate strategies for reducing emissions from the power sector. It is a broad research area. Initially, the...

  6. Nuclear fusion: Pursuing the Soft [Symposium on fusion technology] option

    International Nuclear Information System (INIS)

    Kenward, M.

    1991-01-01

    Fusion research has come a long way since the fusion community held the first Symposium on fusion technology (Soft) in Britain 30 years ago. Some of the recent achievements of the Jet project are reported from this year's symposium, the 16th in the series, held in London at the beginning of September. (author)

  7. Beam Technologies for Integrated Processing

    Science.gov (United States)

    1992-03-01

    magnetic media on tape to optical coatings on polymeric materials. The technologies have progressed in the area of PVD to plasma-assisted CVD ( PACVD ...evaporation of boric acid in an ammonia plasma. Enhanced CVD processes have taken the form of either thermally assisted CVD or PACVD for thermal and electron...temperature-induced irreversible structural or electrical changes. A further process improvement, known as remote PACVD , is used to protect both the

  8. Distillation process using microchannel technology

    Science.gov (United States)

    Tonkovich, Anna Lee [Dublin, OH; Simmons, Wayne W [Dublin, OH; Silva, Laura J [Dublin, OH; Qiu, Dongming [Carbondale, IL; Perry, Steven T [Galloway, OH; Yuschak, Thomas [Dublin, OH; Hickey, Thomas P [Dublin, OH; Arora, Ravi [Dublin, OH; Smith, Amanda [Galloway, OH; Litt, Robert Dwayne [Westerville, OH; Neagle, Paul [Westerville, OH

    2009-11-03

    The disclosed invention relates to a distillation process for separating two or more components having different volatilities from a liquid mixture containing the components. The process employs microchannel technology for effecting the distillation and is particularly suitable for conducting difficult separations, such as the separation of ethane from ethylene, wherein the individual components are characterized by having volatilities that are very close to one another.

  9. Advancements in CAD/CAM technology: Options for practical implementation.

    Science.gov (United States)

    Alghazzawi, Tariq F

    2016-04-01

    The purpose of this review is to present a comprehensive review of the current published literature investigating the various methods and techniques for scanning, designing, and fabrication of CAD/CAM generated restorations along with detailing the new classifications of CAD/CAM technology. I performed a review of a PubMed using the following search terms "CAD/CAM, 3D printing, scanner, digital impression, and zirconia". The articles were screened for further relevant investigations. The search was limited to articles written in English, published from 2001 to 2015. In addition, a manual search was also conducted through articles and reference lists retrieved from the electronic search and peer-reviewed journals. CAD/CAM technology has advantages including digital impressions and models, and use of virtual articulators. However, the implementation of this technology is still considered expensive and requires highly trained personnel. Currently, the design software has more applications including complete dentures and removable partial denture frameworks. The accuracy of restoration fabrication can be best attained with 5 axes milling units. The 3D printing technology has been incorporated into dentistry, but does not include ceramics and is limited to polymers. In the future, optical impressions will be replaced with ultrasound impressions using ultrasonic waves, which have the capability to penetrate the gingiva non-invasively without retraction cords and not be affected by fluids. The coming trend for most practitioners will be the use of an acquisition camera attached to a computer with the appropriate software and the capability of forwarding the image to the laboratory. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  10. Risoe energy report 6. Future options for energy technologies

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Hans; Soenderberg Petersen, L. (eds.)

    2007-11-15

    Fossil fuels provide about 80% of the global energy demand, and this will continue to be the situation for decades to come. In the European Community we are facing two major energy challenges. The first is sustainability, and the second is security of supply, since Europe is becoming more dependent on imported fuels. These challenges are the starting point for the present Risoe Energy Report 6. It gives an overview of the energy scene together with trends and emerging energy technologies. The report presents status and trends for energy technologies seen from a Danish and European perspective from three points of view: security of supply, climate change and industrial perspectives. The report addresses energy supply technologies, efficiency improvements and transport. The report is volume 6 in a series of reports covering energy issues at global, regional and national levels. The individual chapters of the report have been written by staff members from the Technical University of Denmark and Risoe National Laboratory together with leading Danish and international experts. The report is based on the latest research results from Risoe National Laboratory, Technical University of Denmark, together with available internationally recognized scientific material, and is fully referenced and refereed by renowned experts. Information on current developments is taken from the most up-to-date and authoritative sources available. Our target groups are colleagues, collaborating partners, customers, funding organizations, the Danish government and international organizations including the European Union, the International Energy Agency and the United Nations. (au)

  11. Investigating load management technology options: a survey of technologies and issues. Final report. [Competitive interrelationships of LM, conservation, and renewables

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-12-01

    Load-management-technology options are commercially available and may be desirable in many utility-service areas. Energy-conservation and renewable-energy-supply technologies are also cost-effective in many applications and, where installed, may reduce the effectiveness and attractiveness of load-management options. Recent energy legislation has not addressed these competitive interrelationships; future legislation is unlikely to do so unless a coordinated task-force effort among relevant DOE offices is pursued to derive strategic technology and policy recommendations on this issue. R and D strategies should help formulate these recommendations.

  12. Pyro processing technology at KAERI

    International Nuclear Information System (INIS)

    Lee, Hansoo; Kim, Eungho; Park, Seongwon

    2008-01-01

    KAERI has studied on the pyro processing as a spent fuel treatment method for more than decade. The process includes voloxidation, electroreduction, electrorefining with solid and liquid cathodes, and waste salt treatment. Each process has developed its own characteristics which are suitable for treating high mass flow. In the electroreduction process, a magnesia filter was used for integrated electrolytic reduction. More than 99% of reduction yield was achieved. Electrorefining process employs the continuous operation concept. Uranium deposits on the surface of graphite cathode and it is stripped off spontaneously to the bottom of the reactor, which allows continuous operation. Crystallization method was used for treating waste salt. Pure salt is recovered by Czochralski method or zone freezing method and subsequently recycled to the reactor. These advanced technologies ensure the operation of pyro processing in a larger scale

  13. Technology development life cycle processes.

    Energy Technology Data Exchange (ETDEWEB)

    Beck, David Franklin

    2013-05-01

    This report and set of appendices are a collection of memoranda originally drafted in 2009 for the purpose of providing motivation and the necessary background material to support the definition and integration of engineering and management processes related to technology development. At the time there was interest and support to move from Capability Maturity Model Integration (CMMI) Level One (ad hoc processes) to Level Three. As presented herein, the material begins with a survey of open literature perspectives on technology development life cycles, including published data on %E2%80%9Cwhat went wrong.%E2%80%9D The main thrust of the material presents a rational expose%CC%81 of a structured technology development life cycle that uses the scientific method as a framework, with further rigor added from adapting relevant portions of the systems engineering process. The material concludes with a discussion on the use of multiple measures to assess technology maturity, including consideration of the viewpoint of potential users.

  14. Fuel price and technological uncertainty in a real options model for electricity planning

    International Nuclear Information System (INIS)

    Fuss, Sabine; Szolgayova, Jana

    2010-01-01

    Electricity generation is an important source of total CO 2 emissions, which in turn have been found to relate to an acceleration of global warming. Given that many OECD countries have to replace substantial portions of their electricity-generating capacity over the next 10-20 years, investment decisions today will determine the CO 2 -intensity of the future energy mix. But by what type of power plants will old (mostly fossil-fuel-fired) capacity be replaced? Given that modern, less carbon-intensive technologies are still expensive but can be expected to undergo improvements due to technical change in the near future, they may become more attractive, especially if fossil fuel price volatility makes traditional technologies more risky. At the same time, technological progress is an inherently uncertain process itself. In this paper, we use a real options model with stochastic technical change and stochastic fossil fuel prices in order to investigate their impact on replacement investment decisions in the electricity sector. We find that the uncertainty associated with the technological progress of renewable energy technologies leads to a postponement of investment. Even the simultaneous inclusion of stochastic fossil fuel prices in the same model does not make renewable energy competitive compared to fossil-fuel-fired technology in the short run based on the data used. This implies that policymakers have to intervene if renewable energy is supposed to get diffused more quickly. Otherwise, old fossil-fuel-fired equipment will be refurbished or replaced by fossil-fuel-fired capacity again, which enforces the lock-in of the current system into unsustainable electricity generation. (author)

  15. FEATURES OF USING AUGMENTED REALITY TECHNOLOGY TO SUPPORT EDUCATIONAL PROCESSES

    Directory of Open Access Journals (Sweden)

    Yury A. Kravchenko

    2014-01-01

    Full Text Available The paper discusses the concept and technology of augmented reality, the rationale given the relevance and timeliness of its use to support educational processes. Paper is a survey and study of the possibility of using augmented reality technology in education. Architecture is proposed and constructed algorithms of the software system management QR-codes media objects. An overview of the features and uses of augmented reality technology to support educational processes is displayed, as an option of a new form of visual demonstration of complex objects, models and processes

  16. Keeping options open. Energy, technology and sustainable development

    International Nuclear Information System (INIS)

    Rogner, Hans-Holger; Langlois, Lucille; McDonald, Alan

    2001-01-01

    The Ninth Session of the the Commission for Sustainable Development (CSD-9) in April 2001 provided an excellent opportunity for a full debate on the role of nuclear power in sustainable development, as part of its over-all discussion of energy, transport and the atmospheric change issues. On nuclear power, there were two important conclusions. First, countries agreed to disagree on the role of nuclear power in sustainable development. CSD-9's final text recognizes that some countries view nuclear power as incompatible with sustainable development while others believe it is an important contributor to sustainable development. For each case, the reasoning is presented in the text. The second conclusion, on which there was consensus agreement, is that 'the choice of nuclear energy rests with countries'. The arguments in favor of an important role for nuclear power role in sustainable development are that it broadens the resource base by putting uranium to productive use; it reduces harmful emissions; it expands electricity supplies and it increases the world's stock of technological and human capital. It is ahead of other energy technologies in internalizing all externalities, from safety to waste disposal to decommissioning - the costs of all of these are already included in the price of nuclear electricity in most countries. The complete nuclear power chain, from resource extraction to waste disposal including reactor and facility construction, emits only two to kilowatt-hour -- about the same as wind and solar power and two orders of magnitude below coal, oil, and even natural gas. In addition, nuclear power avoids the emission of many other air pollutants, such as SO 2 , NO x and particulates

  17. An accurate European option pricing model under Fractional Stable Process based on Feynman Path Integral

    Science.gov (United States)

    Ma, Chao; Ma, Qinghua; Yao, Haixiang; Hou, Tiancheng

    2018-03-01

    In this paper, we propose to use the Fractional Stable Process (FSP) for option pricing. The FSP is one of the few candidates to directly model a number of desired empirical properties of asset price risk neutral dynamics. However, pricing the vanilla European option under FSP is difficult and problematic. In the paper, built upon the developed Feynman Path Integral inspired techniques, we present a novel computational model for option pricing, i.e. the Fractional Stable Process Path Integral (FSPPI) model under a general fractional stable distribution that tackles this problem. Numerical and empirical experiments show that the proposed pricing model provides a correction of the Black-Scholes pricing error - overpricing long term options, underpricing short term options; overpricing out-of-the-money options, underpricing in-the-money options without any additional structures such as stochastic volatility and a jump process.

  18. Addressing the challenge of providing technological options that ...

    African Journals Online (AJOL)

    Mo

    processing (UNCTAD/WTO, 2001). Recommercialisation of the vanilla industry. In late 1980s some few private companies however joined the industry. They started with the remnants of the colonial era and embarked on teaching and educating farmers about vanilla production.Vanilla production increased and by 1991.

  19. Options in the HCl Process for the Production of Alumina from Clay

    Science.gov (United States)

    Shanks, D. E.; Thompson, D. C.; Arington, R. M.; Dan, G. L.; Eisele, J. A.

    The Bureau of Mines has conducted in-depth studies on the recovery of aluminum chloride hexa-hydrate and alumina from domestic kaolinitic clay. The original goal of the studies was to provide the technology for alumina production from domestic raw materials. Current research is focused on process modifications that would improve the economics of clay-HCl leaching and improve chances for transfer of the technology to commercial use. Options under investigation include direct leaching of raw clay, changes in leaching acid concentration and stoichi-ometry, decreased leaching duration, improved solid-liquid separations, elimination of solvent extraction for iron removal, and formation of basic aluminum chloride instead of aluminum chloride hexahydrate as an intermediate product. Implementation could decrease energy, equipment, and reagent costs by eliminating the calcination step, substituting filtration for thickening and washing circuits, and combining iron removal with aluminum chloride crystallization.

  20. Solar Power System Options for the Radiation and Technology Demonstration Spacecraft

    Science.gov (United States)

    Kerslake, Thomas W.; Haraburda, Francis M.; Riehl, John P.

    2000-01-01

    The Radiation and Technology Demonstration (RTD) Mission has the primary objective of demonstrating high-power (10 kilowatts) electric thruster technologies in Earth orbit. This paper discusses the conceptual design of the RTD spacecraft photovoltaic (PV) power system and mission performance analyses. These power system studies assessed multiple options for PV arrays, battery technologies and bus voltage levels. To quantify performance attributes of these power system options, a dedicated Fortran code was developed to predict power system performance and estimate system mass. The low-thrust mission trajectory was analyzed and important Earth orbital environments were modeled. Baseline power system design options are recommended on the basis of performance, mass and risk/complexity. Important findings from parametric studies are discussed and the resulting impacts to the spacecraft design and cost.

  1. Dealing with uncertainty and pursuing superior technology options in risk management-The inherency risk analysis

    International Nuclear Information System (INIS)

    Helland, Aasgeir

    2009-01-01

    Current regulatory systems focus on the state of scientific evidence as the predominant factor for how to handle risks to human health and the environment. However, production and assessment of risk information are costly and time-consuming, and firms have an intrinsic disincentive to produce and distribute information about risks of their products as this could endanger their production opportunities and sales. An emphasis on more or better science may result in insufficient thought and attention going into the exploration of technology alternatives, and that risk management policies miss out on the possible achievement of a more favorable set of consequences. In this article, a method is proposed that combines risk assessment with the search for alternative technological options as a part of the risk management procedure. The method proposed is the inherency risk analysis where the first stage focuses on the original agent subject to investigation, the second stage focuses on identifying technological options whereas the third stage reviews the different alternatives, searching for the most attractive tradeoffs between costs and inherent safety. This is then used as a fundament for deciding which technology option to pursue. This method aims at providing a solution-focused, systematic technology-based approach for addressing and setting priorities for environmental problems. By combining risk assessment with a structured approach to identify superior technology options within a risk management system, the result could very well be a win-win situation for both company and the environment.

  2. Dealing with uncertainty and pursuing superior technology options in risk management--the inherency risk analysis.

    Science.gov (United States)

    Helland, Aasgeir

    2009-05-30

    Current regulatory systems focus on the state of scientific evidence as the predominant factor for how to handle risks to human health and the environment. However, production and assessment of risk information are costly and time-consuming, and firms have an intrinsic disincentive to produce and distribute information about risks of their products as this could endanger their production opportunities and sales. An emphasis on more or better science may result in insufficient thought and attention going into the exploration of technology alternatives, and that risk management policies miss out on the possible achievement of a more favorable set of consequences. In this article, a method is proposed that combines risk assessment with the search for alternative technological options as a part of the risk management procedure. The method proposed is the inherency risk analysis where the first stage focuses on the original agent subject to investigation, the second stage focuses on identifying technological options whereas the third stage reviews the different alternatives, searching for the most attractive tradeoffs between costs and inherent safety. This is then used as a fundament for deciding which technology option to pursue. This method aims at providing a solution-focused, systematic technology-based approach for addressing and setting priorities for environmental problems. By combining risk assessment with a structured approach to identify superior technology options within a risk management system, the result could very well be a win-win situation for both company and the environment.

  3. Technologies to support industrial processes

    International Nuclear Information System (INIS)

    Palazzi, G.; Savelli, D.

    1989-05-01

    Control and measuring techniques applied to industry have the common aim of increasing safety, reliability and plant availability. The industrial monitoring system needs a lot of sensors, whose signals, elaborated and interpreted, allow one to define the best working condition; moreover control instruments perform a diagnosis related to damages and breakages. The Experimental Engineering Division of ENEA's Thermal Reactor Department has developed sensors and measuring apparatus and has acquired advanced control techniques. All these systems, containing an original software, have been applied to industrial process problems and/or to experimental facilities both to increase reliability and to understand better process physics. Division activities are grouped in four sectors: non-destructive examinations (ultrasonic, eddy current, thermography, holographic interpherometry, penetrant liquids and magnetoscopy); innovative sensors (heated thermocouples, optical fiber sensors); advanced measuring systems (laser technology for fluidodynamic measures, nuclear radiation techniques, infrared measuring, mass spectrometer, hot-film anemometer, chromatographic apparatus); advanced technologies for diagnosis and signal analysis (digital image processing, statistical analysis). (author)

  4. Membrane processes in nuclear technologies

    International Nuclear Information System (INIS)

    Zakrzewska-Trznadel, G.

    2006-01-01

    The treatment of radioactive wastes is necessary taking into account the potential hazard of radioactive substances to human health and surrounding environment. The choice of appropriate technology depends on capital and operational costs, wastes amount and their characteristics, appointed targets of the process, e.g. the values of decontamination factors and volume reduction coefficients. The conventional technologies applied for radioactive waste processing, such as precipitation coupled with sedimentation, ion exchange and evaporation have many drawbacks. These include high energy consumption and formation of secondary wastes, e.g. the sludge from sediment tanks, spent ion exchange adsorbents and regeneration solutions. There are also many limitations of such processes, i.e. foaming and drop entrainment in evaporators, loses of solvents and production of secondary wastes in solvent extraction or bed clogging in ion exchange columns. Membrane processes as the newest achievement of the process engineering can successfully supersede many non-effective, out-of-date methods. But in some instances they can also complement these methods whilst improving the parameters of effluents and purification economy. This monograph presents own research data on the application of recent achievements in the area of membrane processes for solving selected problems in nuclear technology. Relatively big space was devoted to the use of membrane processing of low and intermediate radioactive liquid wastes because of numerous applications of these processes in nuclear centres over the world and also because of the interests of the author that was reflected by her recent research projects and activity. This work presents a review on the membrane methods recently introduced into the nuclear technology against the background of the other, commonly applied separation techniques, with indications of the possibilities and prospects for their further developments. Particular attention was paid

  5. Novel Technological and Management Options for Accelerating Transformational Changes in Rice and Livestock Systems

    Directory of Open Access Journals (Sweden)

    Ngonidzashe Chirinda

    2017-10-01

    Full Text Available Agricultural producers grapple with low farm yields and declining ecosystem services within their landscapes. In several instances, agricultural production systems may be considered largely unsustainable in socioeconomic and ecological (resource conservation and use and impact on nature terms. Novel technological and management options that can serve as vehicles to promote the provision of multiple benefits, including the improvement of smallholder livelihoods, are needed. We call for a paradigm shift to allow designing and implementing agricultural systems that are not only efficient (serving as a means to promote development based on the concept of creating more goods and services while using fewer resources and creating less waste but can also be considered synergistic (symbiotic relationship between socio-ecological systems by simultaneously contributing to major objectives of economic, ecological, and social (equity improvement of agro-ecosystems. These transformations require strategic approaches that are supported by participatory system-level research, experimentation, and innovation. Using data from several studies, we here provide evidence for technological and management options that could be optimized, promoted, and adopted to enable agricultural systems to be efficient, effective, and, indeed, sustainable. Specifically, we present results from a study conducted in Colombia, which demonstrated that, in rice systems, improved water management practices such as Alternate Wetting and Drying (AWD reduce methane emissions (~70%. We also show how women can play a key role in AWD adoption. For livestock systems, we present in vitro evidence showing that the use of alternative feed options such as cassava leaves contributes to livestock feed supplementation and could represent a cost-effective approach for reducing enteric methane emissions (22% to 55%. We argue that to design and benefit from sustainable agricultural systems, there is a

  6. Application of Homotopy Analysis Method to Option Pricing Under Lévy Processes

    OpenAIRE

    Sakuma, Takayuki; Yamada, Yuji

    2014-01-01

    Option pricing under the Lévy process has been considered an important research direction in the field of financial engineering, where a closed-form expression for the standard European option is available due to the existence of analytically tractable characteristic function according to the Lévy–Khinchin representation. However, this approach cannot be applied to exotic derivatives (such as barrier options) directly, although a large volume of exotic derivatives are actively traded in the c...

  7. Commercial Parts Technology Qualification Processes

    Science.gov (United States)

    Cooper, Mark S.

    2013-01-01

    Many high-reliability systems, including space systems, use selected commercial parts (including Plastic Encapsulated Microelectronics or PEMs) for unique functionality, small size, low weight, high mechanical shock resistance, and other factors. Predominantly this usage is subjected to certain 100% tests (typically called screens) and certain destructive tests usually (but not always) performed on the flight lot (typically called qualification tests). Frequently used approaches include those documented in EEE-INST-002 and JPL DocID62212 (which are sometimes modified by the particular aerospace space systems manufacturer). In this study, approaches from these documents and several space systems manufacturers are compared to approaches from a launch systems manufacturer (SpaceX), an implantable medical electronics manufacturer (Medtronics), and a high-reliability transport system process (automotive systems). In the conclusions section, these processes are outlined for all of these cases and presented in tabular form. Then some simple comparisons are made. In this introduction section, the PEM technology qualification process is described, as documented in EEE-INST-002 (written by the Goddard Space Flight Center, GSFC), as well as the somewhat modified approach employed at the Jet Propulsion Laboratory (JPL). Approaches used at several major NASA contractors are also described

  8. Analysis of technological options for electric energy generation from urban solid wastes; Analise de opcoes tecnologicas para geracao de energia eletrica a partir de residuos solidos urbanos

    Energy Technology Data Exchange (ETDEWEB)

    Furtado, J.G. de M.; Serra, E.T. [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil)], Emails: furtado@cepel.br, etserra@cepel.br

    2010-07-01

    This paper evaluates technologically of the options existents for generation of electric power from the urban solid wastes (USW), based on application of factoring method for estimation of investments based on basic description of the plant, it main equipment and technological complexity, viewing to contribute for determination of better technical and economical form, and the energy using. The results of the effectuated analyses indicates that the most technological complexity of the gasification and thermal plasma, and be encountered on non commercial in great scale as well, make the the option present the greatest index of investment and relative cost, determining the greatest costs of electric power generated through this process.

  9. Management of Technology - a political process approach

    DEFF Research Database (Denmark)

    Koch, Christian

    1999-01-01

    Most management of technology writings fail to address enterprise developments as political processes, where visions, coalitions and emergence are central features. The paper report of a participants observation study of management of technology processes.......Most management of technology writings fail to address enterprise developments as political processes, where visions, coalitions and emergence are central features. The paper report of a participants observation study of management of technology processes....

  10. Tenuous Options: The Career Development Process for Undocumented Students

    Science.gov (United States)

    Ortiz, Anna M.; Hinojosa, Alejandro

    2010-01-01

    This chapter explores the challenges that undocumented students face as they enact their career development process, considering the theoretical perspectives and developmental processes that uniquely complicate their aspirations. The authors review the professional development challenges that undocumented students face as they make career…

  11. The process system analysis for advanced spent fuel management technology (I)

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. H.; Lee, J. R.; Kang, D. S.; Seo, C. S.; Shin, Y. J.; Park, S. W.

    1997-12-01

    Various pyrochemical processes were evaluated, and viable options were selected in consideration of the proliferation safety, technological feasibility and compatibility to the domestic nuclear power system. Detailed technical analysis were followed on the selected options such as unit process flowsheet including physico-chemical characteristics of the process systems, preliminary concept development, process design criteria and materials for equipment. Supplementary analysis were also carried out on the support technologies including sampling and transport technologies of molten salt, design criteria and equipment for glove box systems, and remote operation technologies. (author). 40 refs., 49 tabs., 37 figs.

  12. A review on technological options of waste to energy for effective management of municipal solid waste.

    Science.gov (United States)

    Kumar, Atul; Samadder, S R

    2017-11-01

    Approximately one-fourth population across the world rely on traditional fuels (kerosene, natural gas, biomass residue, firewood, coal, animal dung, etc.) for domestic use despite significant socioeconomic and technological development. Fossil fuel reserves are being exploited at a very fast rate to meet the increasing energy demands, so there is a need to find alternative sources of energy before all the fossil fuel reserves are depleted. Waste to energy (WTE) can be considered as a potential alternative source of energy, which is economically viable and environmentally sustainable. The present study reviewed the current global scenario of WTE technological options (incineration, pyrolysis, gasification, anaerobic digestion, and landfilling with gas recovery) for effective energy recovery and the challenges faced by developed and developing countries. This review will provide a framework for evaluating WTE technological options based on case studies of developed and developing countries. Unsanitary landfilling is the most commonly practiced waste disposal option in the developing countries. However, developed countries have realised the potential of WTE technologies for effective municipal solid waste management (MSWM). This review will help the policy makers and the implementing authorities involved in MSWM to understand the current status, challenges and barriers for effective management of municipal solid waste. This review concluded WTE as a potential renewable source of energy, which will partly meet the energy demand and ensure effective MSWM. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Process Heat Exchanger Options for Fluoride Salt High Temperature Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Piyush Sabharwall; Eung Soo Kim; Michael McKellar; Nolan Anderson

    2011-04-01

    The work reported herein is a significant intermediate step in reaching the final goal of commercial-scale deployment and usage of molten salt as the heat transport medium for process heat applications. The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production and process heat application, which would support large-scale deployment.

  14. Process Heat Exchanger Options for the Advanced High Temperature Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Piyush Sabharwall; Eung Soo Kim; Michael McKellar; Nolan Anderson

    2011-06-01

    The work reported herein is a significant intermediate step in reaching the final goal of commercial-scale deployment and usage of molten salt as the heat transport medium for process heat applications. The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production and process heat application, which would support large-scale deployment.

  15. A Miniature Membrane Reactor for Evaluation of Process Design Options on the Enzymatic Degradation of Pectin

    DEFF Research Database (Denmark)

    Zainal Alam, Muhd Nazrul Hisham; Pinelo, Manuel; Arnous, Anis

    2011-01-01

    The objective of this paper is to assess if a membrane microbioreactor system could potentially be used to diagnose consequences of different process design and reactor operation options relevant for larger-scale enzymatic degradation of pectin reactions. The membrane microbioreactor prototype...... design affected the membrane rejection profile. The results obtained thus underlined the suitability of a miniature membrane reactor system for evaluating different process design options that are relevant for larger-scale reactions of enzymatic pectin degradation....

  16. Buried waste integrated demonstration technology integration process

    International Nuclear Information System (INIS)

    Ferguson, J.S.; Ferguson, J.E.

    1992-04-01

    A Technology integration Process was developed for the Idaho National Energy Laboratories (INEL) Buried Waste Integrated Demonstration (BWID) Program to facilitate the transfer of technology and knowledge from industry, universities, and other Federal agencies into the BWID; to successfully transfer demonstrated technology and knowledge from the BWID to industry, universities, and other Federal agencies; and to share demonstrated technologies and knowledge between Integrated Demonstrations and other Department of Energy (DOE) spread throughout the DOE Complex. This document also details specific methods and tools for integrating and transferring technologies into or out of the BWID program. The document provides background on the BWID program and technology development needs, demonstrates the direction of technology transfer, illustrates current processes for this transfer, and lists points of contact for prospective participants in the BWID technology transfer efforts. The Technology Integration Process was prepared to ensure compliance with the requirements of DOE's Office of Technology Development (OTD)

  17. Geothermal injection treatment: process chemistry, field experiences, and design options

    Energy Technology Data Exchange (ETDEWEB)

    Kindle, C.H.; Mercer, B.W.; Elmore, R.P.; Blair, S.C.; Myers, D.A.

    1984-09-01

    The successful development of geothermal reservoirs to generate electric power will require the injection disposal of approximately 700,000 gal/h (2.6 x 10/sup 6/ 1/h) of heat-depleted brine for every 50,000 kW of generating capacity. To maintain injectability, the spent brine must be compatible with the receiving formation. The factors that influence this brine/formation compatibility and tests to quantify them are discussed in this report. Some form of treatment will be necessary prior to injection for most situations; the process chemistry involved to avoid and/or accelerate the formation of precipitate particles is also discussed. The treatment processes, either avoidance or controlled precipitation approaches, are described in terms of their principles and demonstrated applications in the geothermal field and, when such experience is limited, in other industrial use. Monitoring techniques for tracking particulate growth, the effect of process parameters on corrosion and well injectability are presented. Examples of brine injection, preinjection treatment, and recovery from injectivity loss are examined and related to the aspects listed above.

  18. Arms Control and nonproliferation technologies: Technology options and associated measures for monitoring a Comprehensive Test Ban, Second quarter

    Energy Technology Data Exchange (ETDEWEB)

    Casey, Leslie A.

    1994-01-01

    This newsletter contains reprinted papers discussing technology options and associated measures for monitoring a Comprehensive Test Ban Treaty (CTBT). These papers were presented to the Conference on Disarmament (CD) in May and June 1994. An interagency Verification Monitoring Task Force developed the papers. The task force included participants from the Arms Control and Disarmament Agency, the Department of Defense, the Department of Energy, the Intelligence Community, the Department of Interior, and the Department of State. The purpose of this edition of Arms Control and Nonproliferation Technologies is to share these papers with the broad base of stakeholders in a CTBT and to facilitate future technology discussions. The papers in the first group discuss possible technology options for monitoring a CTBT in all environments (underground, underwater, atmosphere, and space). These technologies, along with on-site inspections, would facilitate CTBT monitoring by treaty participants. The papers in the second group present possible associated measures, e.g., information exchanges and transparency measures, that would build confidence among states participating in a CTBT.

  19. Bilişim Teknolojisi Projelerinde Reel Opsiyonlar (Real Options in Information Technology Projects

    Directory of Open Access Journals (Sweden)

    İpek Deveci KOCAKOÇ

    2009-10-01

    Full Text Available Many sources such as the immaturity, complexity and unpredictable evolution of the technologies themselves, and the difficulty of predicting the market demand generally cause uncertainty in the Information Technology (IT projects. Managerial flexibility has value in the context of uncertain IT projects, as management can continuously gather information about uncertain project and market characteristics and, based on this information, change its course of action. As traditional capital budgeting (or project appraisal approaches fail to consider embedded managerial flexibility in projects, the new investment evaluation approach called “real options” has come on the scene recently. “Options thinking,” an emerging investment management philosophy based on the theory of financial options can provide a promising foundation for hedging the risks under uncertainty. This paper aims at analyzing a real IT investment having growth opportunities by using real options approach. Specifically, the value of investing in a software project as well as embedded flexibility in this opportunity is modeled as an option contract. The expected costs required for completing the project and thereafter the resulting asset value are considered as the base-case parameters of this contract. Option values derived from Binomial method are used for evaluating the project and the optimal investment policy is determined based on these values. As a result, it is shown that the value of an IT project having flexibility can differ from one obtained with traditional capital budgeting methods and a rejected project which was seen as unprofitable before can turn a profitable one through embedded flexibilities.

  20. A real-life example of choosing an inherently safer process option

    International Nuclear Information System (INIS)

    Study, Karen

    2007-01-01

    While choosing an inherently safer alternative may seem straightforward, sometimes what seems to be the most obvious alternative may not provide the best risk reduction. The process designer must maintain a broad perspective to be able to recognize all potential hazards when evaluating design options. All aspects of operation such as start-up, shut-down, utility failure, as well as normal operation should be considered. Choosing the inherently safer option is best accomplished early in the option selection phase of a project; however, recycle back to the option selection phase may be needed if an option is not thoroughly evaluated early in the process. In this paper, a project to supply ammonia to a catalytic reactor will be reviewed. During the course of the project, an 'inherently safer' alternative was selected and later discarded due to issues uncovered during the detail design phase. The final option chosen will be compared to (1) the original design and (2) the initial 'inherently safer' alternative. The final option was inherently safer than both the original design and the initial 'inherently safer' alternative even though the design team initially believed that it would not be

  1. Finite Difference Methods for Option Pricing under Lévy Processes: Wiener-Hopf Factorization Approach

    OpenAIRE

    Kudryavtsev, Oleg

    2013-01-01

    In the paper, we consider the problem of pricing options in wide classes of Lévy processes. We propose a general approach to the numerical methods based on a finite difference approximation for the generalized Black-Scholes equation. The goal of the paper is to incorporate the Wiener-Hopf factorization into finite difference methods for pricing options in Lévy models with jumps. The method is applicable for pricing barrier and American options. The pricing problem is reduced to the sequence o...

  2. 76 FR 37344 - Technology Evaluation Process

    Science.gov (United States)

    2011-06-27

    ...-NOA-0039] Technology Evaluation Process AGENCY: Office of Energy Efficiency and Renewable Energy... evaluation process. The stakeholder comment period is being extended an additional 30 days to give potential... seeks comments and information related to a commercial buildings technology evaluation process. DOE is...

  3. Biofuels Fuels Technology Pathway Options for Advanced Drop-in Biofuels Production

    Energy Technology Data Exchange (ETDEWEB)

    Kevin L Kenney

    2011-09-01

    Advanced drop-in hydrocarbon biofuels require biofuel alternatives for refinery products other than gasoline. Candidate biofuels must have performance characteristics equivalent to conventional petroleum-based fuels. The technology pathways for biofuel alternatives also must be plausible, sustainable (e.g., positive energy balance, environmentally benign, etc.), and demonstrate a reasonable pathway to economic viability and end-user affordability. Viable biofuels technology pathways must address feedstock production and environmental issues through to the fuel or chemical end products. Potential end products include compatible replacement fuel products (e.g., gasoline, diesel, and JP8 and JP5 jet fuel) and other petroleum products or chemicals typically produced from a barrel of crude. Considering the complexity and technology diversity of a complete biofuels supply chain, no single entity or technology provider is capable of addressing in depth all aspects of any given pathway; however, all the necessary expert entities exist. As such, we propose the assembly of a team capable of conducting an in-depth technology pathway options analysis (including sustainability indicators and complete LCA) to identify and define the domestic biofuel pathways for a Green Fleet. This team is not only capable of conducting in-depth analyses on technology pathways, but collectively they are able to trouble shoot and/or engineer solutions that would give industrial technology providers the highest potential for success. Such a team would provide the greatest possible down-side protection for high-risk advanced drop-in biofuels procurement(s).

  4. Economic, energy and greenhouse emissions impacts of some consumer choice, technology and government outlay options

    International Nuclear Information System (INIS)

    Lenzen, Manfred; Dey, Christopher J.

    2002-01-01

    The impacts of selected spending options in the Australian economy are determined in terms of energy consumption, greenhouse gas emissions and a range of economic parameters. Six case studies of one current-practice and one alternative, environmentally motivated spending option are carried out, describing consumer choices, technologies and government outlays. The assessment method is based on input-output theory and, as such, enables both the direct and indirect effects of spending to be quantified. In general, the results indicate that pro-environmental objectives, such as reductions in energy consumption and greenhouse gas emissions, are compatible with broad socio-economic benefits, such as increases in employment and income, and reductions in imports

  5. Processing techniques applying laser technology

    International Nuclear Information System (INIS)

    Yamada, Yuji; Makino Yoshinobu

    2000-01-01

    The requirements for the processing of nuclear energy equipment include high precision, low distortion, and low heat input. Toshiba has developed laser processing techniques for cutting, welding, and surface heat treatment of nuclear energy equipment because the zone affected by distortion and heat in laser processing is very small. Laser processing contributes to the manufacturing of high-quality and high-reliability equipment and reduces the manufacturing period. (author)

  6. Proceedings of the 1999 Oil and Gas Conference: Technology Options for Producer Survival

    Energy Technology Data Exchange (ETDEWEB)

    None available

    2000-04-12

    The 1999 Oil & Gas Conference was cosponsored by the U.S. Department of Energy (DOE), Office of Fossil Energy, Federal Energy Technology Center (FETC) and National Petroleum Technology Office (NPTO) on June 28 to 30 in Dallas, Texas. The Oil & Gas Conference theme, Technology Options for Producer Survival, reflects the need for development and implementation of new technologies to ensure an affordable, reliable energy future. The conference was attended by nearly 250 representatives from industry, academia, national laboratories, DOE, and other Government agencies. Three preconference workshops (Downhole Separation Technologies: Is it Applicable for Your Operations, Exploring and developing Naturally Fractured Low-Permeability Gas Reservoirs from the Rocky Mountains to the Austin Chalk, and Software Program Applications) were held. The conference agenda included an opening plenary session, three platform sessions (Sessions 2 and 3 were split into 2 concurrent topics), and a poster presentation reception. The platform session topics were Converting Your Resources Into Reserves (Sessions 1 and 2A), Clarifying Your Subsurface Vision (Session 2B), and High Performance, Cost Effective Drilling, Completion, Stimulation Technologies (Session 3B). In total, there were 5 opening speakers, 30 presenters, and 16 poster presentations.

  7. Technology strategy for subsea processing and transport; Technology Target Areas; TTA6 - Subsea processing and transportation

    Energy Technology Data Exchange (ETDEWEB)

    2008-07-01

    OG21 (www.OG21.org) Norway's official technology strategy for the petroleum sector issued a revised strategy document in November 2005 (new strategy planned in 2009). In this document 'Subsea processing and transport' was identified as one of the eight new technology target areas (TTAs). The overall OG21 strategy document is on an aggregated level, and therefore the Board of OG21 decided that a sub-strategy for each TTA was needed. This document proposes the sub-strategy for the technology target area 'Subsea processing and transport' which covers the technology and competence necessary to effectively transport well stream to a platform or to onshore facilities. This includes multiphase flow modelling, flow assurance challenges to avoid problems with hydrates, asphaltenes and wax, subsea or downhole fluid conditioning including bulk water removal, and optionally complete water removal, and sand handling. It also covers technologies to increase recovery by pressure boosting from subsea pumping and/or subsea compression. Finally it covers technologies to facilitate subsea processing such as control systems and power supply. The vision of the Subsea processing and transport TTA is: Norway is to be the leading international knowledge- and technology cluster in subsea processing and transport: Sustain increased recovery and accelerated production on the NCS by applying subsea processing and efficient transport solutions; Enable >500 km gas/condensate multiphase well stream transport; Enable >200 km oil-dominated multiphase well stream transport; Enable well stream transport of complex fluids; Enable subsea separation, boosting compression, and water injection; Enable deepwater developments; Enable environmentally friendly and energy efficient field development. Increase the export of subsea processing and transport technology: Optimize technology from the NCS for application worldwide; Develop new technology that can meet the challenges found in

  8. Mission Architecture and Technology Options for a Flagship Class Venus In Situ Mission

    Science.gov (United States)

    Balint, Tibor S.; Kwok, Johnny H.; Kolawa, Elizabeth A.; Cutts, James A.; Senske, David A.

    2008-01-01

    Venus, as part of the inner triad with Earth and Mars, represents an important exploration target if we want to learn more about solar system formation and evolution. Comparative planetology could also elucidate the differences between the past, present, and future of these three planets, and can help with the characterization of potential habitable zones in our solar system and, by extension, extrasolar systems. A long lived in situ Venus mission concept, called the Venus Mobile Explorer, was prominently featured in NASA's 2006 SSE Roadmap and supported in the community White Paper by the Venus Exploration Analysis Group (VEXAG). Long-lived in situ missions are expected to belong to the largest (Flagship) mission class, which would require both enabling and enhancing technologies beside mission architecture options. Furthermore, extreme environment mitigation technologies for Venus are considered long lead development items and are expected to require technology development through a dedicated program. To better understand programmatic and technology needs and the motivating science behind them, in this fiscal year (FY08) NASA is funding a Venus Flaghip class mission study, based on key science and technology drivers identified by a NASA appointed Venus Science and Technology Definition Team (STDT). These mission drivers are then assembled around a suitable mission architecture to further refine technology and cost elements. In this paper we will discuss the connection between the final mission architecture and the connected technology drivers from this NASA funded study, which - if funded - could enable a future Flagship class Venus mission and potentially drive a proposed Venus technology development program.

  9. Determinants of improved cassava processing technologies' (ICPT ...

    African Journals Online (AJOL)

    Determinants of improved cassava processing technologies' (ICPT) utilization among rural processors in Oyo State. ... Journal of Agriculture, Forestry and the Social Sciences ... Abstract. The study examined the factors determining the utilization of Improved Cassava Processing Technologies (ICPTs) in Oyo State, Nigeria.

  10. Radioactive Dry Process Material Treatment Technology Development

    Energy Technology Data Exchange (ETDEWEB)

    Park, J. J.; Hung, I. H.; Kim, K. K. (and others)

    2007-06-15

    The project 'Radioactive Dry Process Material Treatment Technology Development' aims to be normal operation for the experiments at DUPIC fuel development facility (DFDF) and safe operation of the facility through the technology developments such as remote operation, maintenance and pair of the facility, treatment of various high level process wastes and trapping of volatile process gases. DUPIC Fuel Development Facility (DFDF) can accommodate highly active nuclear materials, and now it is for fabrication of the oxide fuel by dry process characterizing the proliferation resistance. During the second stage from march 2005 to February 2007, we carried out technology development of the remote maintenance and the DFDF's safe operation, development of treatment technology for process off-gas, and development of treatment technology for PWR cladding hull and the results was described in this report.

  11. The Center for Environmental Technology Innovative Technology Screening Process

    International Nuclear Information System (INIS)

    Bertrand, C.M.

    1995-02-01

    The Center for Environmental Technology's (CET) mission is to provide a fully integrated system for accelerated evaluation, development, commercialization, and public acceptance of creative environmental solutions which match the foremost demands in today's environmentally sensitive world. In short, CET will create a means to provide quick, effective solutions for environmental needs. To meet this mission objective, CET has created a unique and innovative approach to eliminating the usual barriers in developing and testing environmental technologies. The approach paves the way for these emerging, cutting-edge technologies by coordinating environmental restoration and waste management activities of industry, universities, and the government to: efficiently and effectively transfer technology to these users, provide market-driven, cost-effective technology programs to the public and DOE, and aid in developing innovative ideas by initiating efforts between DOE facilities and private industry. The central part to this mission is selecting and evaluating specific innovative technologies for demonstration and application at United States Department of Energy (DOE) installations. The methodology and criteria used for this selection, which is called the CET Innovative Technology Screening Process, is the subject of this paper. The selection criteria used for the screening process were modeled after other DOE technology transfer programs and were further developed by CET's Technology Screening and Evaluation Board (TSEB). The process benefits both CET and the proposing vendors by providing objective selection procedures based on predefined criteria. The selection process ensures a rapid response to proposing vendors, all technologies will have the opportunity to enter the selection process, and all technologies are evaluated on the same scale and with identical criteria

  12. Multi-technology option strategy for long term R and D programs on plutonium technologies. Minimizing proliferation risks and preparing for the future

    International Nuclear Information System (INIS)

    Suzuki, Tatsujiro

    1997-01-01

    Plutonium programs worldwide are now facing major economic, political and technical challenges. New strategies need to address two distinctive global concerns: minimizing proliferation risks associated with plutonium use, and keeping the options alive to prepare for uncertain energy future. In order to meet those challenges, this paper proposes the introduction of 'multi-technology option strategy'. Such strategy is designed to keep so-called 'technological readiness' state of plutonium technologies worldwide without committing to a fixed technology option and exploring more innovative various technology options. This paper also suggests that such R and D programs can be coordinated and shared among nations that are interested in future plutonium use, and such cooperation can improve transparency of sensitive R and D programs. (author)

  13. Separation process using microchannel technology

    Science.gov (United States)

    Tonkovich, Anna Lee [Dublin, OH; Perry, Steven T [Galloway, OH; Arora, Ravi [Dublin, OH; Qiu, Dongming [Bothell, WA; Lamont, Michael Jay [Hilliard, OH; Burwell, Deanna [Cleveland Heights, OH; Dritz, Terence Andrew [Worthington, OH; McDaniel, Jeffrey S [Columbus, OH; Rogers, Jr; William, A [Marysville, OH; Silva, Laura J [Dublin, OH; Weidert, Daniel J [Lewis Center, OH; Simmons, Wayne W [Dublin, OH; Chadwell, G Bradley [Reynoldsburg, OH

    2009-03-24

    The disclosed invention relates to a process and apparatus for separating a first fluid from a fluid mixture comprising the first fluid. The process comprises: (A) flowing the fluid mixture into a microchannel separator in contact with a sorption medium, the fluid mixture being maintained in the microchannel separator until at least part of the first fluid is sorbed by the sorption medium, removing non-sorbed parts of the fluid mixture from the microchannel separator; and (B) desorbing first fluid from the sorption medium and removing desorbed first fluid from the microchannel separator. The process and apparatus are suitable for separating nitrogen or methane from a fluid mixture comprising nitrogen and methane. The process and apparatus may be used for rejecting nitrogen in the upgrading of sub-quality methane.

  14. Process Guide for Deburring Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Frey, David L.

    2012-10-25

    This report is an updated and consolidated view of the current deburring processes at the Kansas City Plant (KCP). It includes specific examples of current burr problems and the methods used for their detection. Also included is a pictorial review of the large variety of available deburr tools, along with a complete numerical listing of existing tools and their descriptions. The process for deburring all the major part feature categories is discussed.

  15. By-product utilisation within the Jamaica Broilers Group and factors determining secondary processing options implemented

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, V. [Jamaica Broilers Group (Jamaica)

    1996-10-01

    Waste disposal within the agro-industrial sector of Jamaica was discussed. Seven options for utilisation of processing by-products within the Jamaica Broilers Group, which is involved in the production and processing of poultry, beef and fish, were presented. These were: rendering, composting, biofermentation, dry extrusion lagoons, biodigesters, solar drying, engineered marshes, and dumping. The criteria to be considered for an option to be effective were: location, type of by-product produced, and re-use potential of the end product. 4 figs.

  16. INHOMOGENEITY IN SPATIAL COX POINT PROCESSES – LOCATION DEPENDENT THINNING IS NOT THE ONLY OPTION

    Directory of Open Access Journals (Sweden)

    Michaela Prokešová

    2010-11-01

    Full Text Available In the literature on point processes the by far most popular option for introducing inhomogeneity into a point process model is the location dependent thinning (resulting in a second-order intensity-reweighted stationary point process. This produces a very tractable model and there are several fast estimation procedures available. Nevertheless, this model dilutes the interaction (or the geometrical structure of the original homogeneous model in a special way. When concerning the Markov point processes several alternative inhomogeneous models were suggested and investigated in the literature. But it is not so for the Cox point processes, the canonical models for clustered point patterns. In the contribution we discuss several other options how to define inhomogeneous Cox point process models that result in point patterns with different types of geometric structure. We further investigate the possible parameter estimation procedures for such models.

  17. Electrochromic Windows: Advanced Processing Technology

    Energy Technology Data Exchange (ETDEWEB)

    SAGE Electrochromics, Inc

    2006-12-13

    This project addresses the development of advanced fabrication capabilities for energy saving electrochromic (EC) windows. SAGE EC windows consist of an inorganic stack of thin films deposited onto a glass substrate. The window tint can be reversibly changed by the application of a low power dc voltage. This property can be used to modulate the amount of light and heat entering buildings (or vehicles) through the glazings. By judicious management of this so-called solar heat gain, it is possible to derive significant energy savings due to reductions in heating lighting, and air conditioning (HVAC). Several areas of SAGE’s production were targeted during this project to allow significant improvements to processing throughput, yield and overall quality of the processing, in an effort to reduce the cost and thereby improve the market penetration. First, the overall thin film process was optimized to allow a more robust set of operating points to be used, thereby maximizing the yield due to the thin film deposition themselves. Other significant efforts aimed at improving yield were relating to implementing new procedures and processes for the manufacturing process, to improve the quality of the substrate preparation, and the quality of the IGU fabrication. Furthermore, methods for reworking defective devices were developed, to enable devices which would otherwise be scrapped to be made into useful product. This involved the in-house development of some customized equipment. Finally, the improvements made during this project were validated to ensure that they did not impact the exceptional durability of the SageGlass® products. Given conservative estimates for cost and market penetration, energy savings due to EC windows in residences in the US are calculated to be of the order 0.026 quad (0.026×1015BTU/yr) by the year 2017.

  18. Selection of efficient options for processing and storage of radioactive waste in countries with small amounts of waste generation

    International Nuclear Information System (INIS)

    2003-09-01

    The report is intended to assist decision makers in countries using nuclear energy for non-power applications to organize their waste management practices. It describes methodologies, criteria and options for the selection of appropriate technologies for processing and storage of low and intermediate level radioactive waste from different nuclear applications. The report reviews both technical and non-technical factors important for decision making and planning, and for implementation of waste management activities at the country and facility levels. It makes practical recommendations for the selection of particular technologies for different scales of waste generation. These wastes may arise from production of radionuclides and their application in industry, agriculture, medicine, education and research. The report also considers waste generated at research reactors, research centers and research laboratories using radioisotopes, as well as waste from decommissioning of research reactors and small nuclear facilities such as hot cells, laboratories and irradiation facilities. Management of uranium mining and milling waste and management of spent fuel from research reactors are not considered in this report. Discussed in detail are: the basic legal, regulatory, administrative and technical requirements set up in a national waste management system and review of the factors and components affecting the selection of an appropriate national waste management system. the origins and characteristics of radioactive waste from different nuclear applications. the technical factors that might affect the selection of waste processing and storage technologies, the main waste management steps, information on available technologies, the basis for planning of waste processing and storage and the selection of a particular option for radioactive waste processing and storage in countries with a different scale of nuclear applications

  19. Quantum information processing : science & technology.

    Energy Technology Data Exchange (ETDEWEB)

    Horton, Rebecca; Carroll, Malcolm S.; Tarman, Thomas David

    2010-09-01

    Qubits demonstrated using GaAs double quantum dots (DQD). The qubit basis states are the (1) singlet and (2) triplet stationary states. Long spin decoherence times in silicon spurs translation of GaAs qubit in to silicon. In the near term the goals are: (1) Develop surface gate enhancement mode double quantum dots (MOS & strained-Si/SiGe) to demonstrate few electrons and spin read-out and to examine impurity doped quantum-dots as an alternative architecture; (2) Use mobility, C-V, ESR, quantum dot performance & modeling to feedback and improve upon processing, this includes development of atomic precision fabrication at SNL; (3) Examine integrated electronics approaches to RF-SET; (4) Use combinations of numerical packages for multi-scale simulation of quantum dot systems (NEMO3D, EMT, TCAD, SPICE); and (5) Continue micro-architecture evaluation for different device and transport architectures.

  20. Wood Technology: Techniques, Processes, and Products

    Science.gov (United States)

    Oatman, Olan

    1975-01-01

    Seven areas of wood technology illustrates applicable techniques, processes, and products for an industrial arts woodworking curriculum. They are: wood lamination; PEG (polyethylene glycol) diffusion processes; wood flour and/or particle molding; production product of industry; WPC (wood-plastic-composition) process; residential construction; and…

  1. Microwave plasma emerging technologies for chemical processes

    NARCIS (Netherlands)

    de la Fuente, Javier F.; Kiss, Anton A.; Radoiu, Marilena T.; Stefanidis, Georgios D.

    2017-01-01

    Microwave plasma (MWP) technology is currently being used in application fields such as semiconductor and material processing, diamond film deposition and waste remediation. Specific advantages of the technology include the enablement of a high energy density source and a highly reactive medium,

  2. TECHNOLOGICAL PROCESS OF EFFLUENTS DEPHENOLYSATION

    Directory of Open Access Journals (Sweden)

    В. Трачевський

    2011-02-01

    Full Text Available The one of the important physical factors impacting on the environmental safety of industrial wastewater generated in the production of paints and varnishes is considered. Identification wastewater formation sources, composition, its amount in a particular type of resin is an essential point for developing methods of cleaning industrial wastewater treatment design and industrial plants. Deep cleaning of wastewater from phenol is a major challenge. Studies that mostly focused on the known methods of disposal of waste waters from phenol have been analyzed. It was shown that the shortcomings of many methods of sewage treatment of phenols by condensation at atmospheric pressure are the long duration of the process, significant cost of heat, and large residual phenol concentration in water, respectively. The most effective method of reducing the concentration of phenol in waste water is its oxidation in MnO2 suspension. The interaction of manganese oxides with sulfuric acid produces oxygen, which can oxidise phenol contained in the waste water. As a result of wastewater treatment of phenolic resins by manganese oxides in acidic sulfate medium phenol concentration  was decreased by 98.6 - 99.6%.

  3. Process analytical technology (PAT) for biopharmaceuticals

    DEFF Research Database (Denmark)

    Glassey, Jarka; Gernaey, Krist; Clemens, Christoph

    2011-01-01

    Process analytical technology (PAT), the regulatory initiative for building in quality to pharmaceutical manufacturing, has a great potential for improving biopharmaceutical production. The recommended analytical tools for building in quality, multivariate data analysis, mechanistic modeling, nov...

  4. Study on Venture Capital Investment Risk Avoiding Base on Option Pricing in Agricultural Production and Processing Enterprises

    Science.gov (United States)

    Zhang, Xubo

    This paper uses the approaches and models of option theory to analyze two-stage venture capital investment in agricultural production and processing enterprises decision-making under uncertainty. Mathematics expressions of this two-stage venture capital investment decision-making are presented. An option value model about two-stage venture capital investment decision-making base on options pricing theory under the uncertainty is presented. Get the solution of option pricing model which we present.

  5. Tight Error Bounds for Fourier Methods for Option Pricing for Exponential Levy Processes

    KAUST Repository

    Crocce, Fabian

    2016-01-06

    Prices of European options whose underlying asset is driven by the L´evy process are solutions to partial integrodifferential Equations (PIDEs) that generalise the Black-Scholes equation by incorporating a non-local integral term to account for the discontinuities in the asset price. The Levy -Khintchine formula provides an explicit representation of the characteristic function of a L´evy process (cf, [6]): One can derive an exact expression for the Fourier transform of the solution of the relevant PIDE. The rapid rate of convergence of the trapezoid quadrature and the speedup provide efficient methods for evaluationg option prices, possibly for a range of parameter configurations simultaneously. A couple of works have been devoted to the error analysis and parameter selection for these transform-based methods. In [5] several payoff functions are considered for a rather general set of models, whose characteristic function is assumed to be known. [4] presents the framework and theoretical approach for the error analysis, and establishes polynomial convergence rates for approximations of the option prices. [1] presents FT-related methods with curved integration contour. The classical flat FT-methods have been, on the other hand, extended for option pricing problems beyond the European framework [3]. We present a methodology for studying and bounding the error committed when using FT methods to compute option prices. We also provide a systematic way of choosing the parameters of the numerical method, minimising the error bound and guaranteeing adherence to a pre-described error tolerance. We focus on exponential L´evy processes that may be of either diffusive or pure jump in type. Our contribution is to derive a tight error bound for a Fourier transform method when pricing options under risk-neutral Levy dynamics. We present a simplified bound that separates the contributions of the payoff and of the process in an easily processed and extensible product form that

  6. Wafer level 3-D ICs process technology

    CERN Document Server

    Tan, Chuan Seng; Reif, L Rafael

    2009-01-01

    This book focuses on foundry-based process technology that enables the fabrication of 3-D ICs. The core of the book discusses the technology platform for pre-packaging wafer lever 3-D ICs. However, this book does not include a detailed discussion of 3-D ICs design and 3-D packaging. This is an edited book based on chapters contributed by various experts in the field of wafer-level 3-D ICs process technology. They are from academia, research labs and industry.

  7. A scenario analysis of future energy systems based on an energy flow model represented as functionals of technology options

    International Nuclear Information System (INIS)

    Kikuchi, Yasunori; Kimura, Seiichiro; Okamoto, Yoshitaka; Koyama, Michihisa

    2014-01-01

    Highlights: • Energy flow model was represented as the functionals of technology options. • Relationships among available technologies can be visualized by developed model. • Technology roadmapping can be incorporated into the model as technical scenario. • Combination of technologies can increase their contribution to the environment. - Abstract: The design of energy systems has become an issue all over the world. A single optimal system cannot be suggested because the availability of infrastructure and resources and the acceptability of the system should be discussed locally, involving all related stakeholders in the energy system. In particular, researchers and engineers of technologies related to energy systems should be able to perform the forecasting and roadmapping of future energy systems and indicate quantitative results of scenario analyses. We report an energy flow model developed for analysing scenarios of future Japanese energy systems implementing a variety of feasible technology options. The model was modularized and represented as functionals of appropriate technology options, which enables the aggregation and disaggregation of energy systems by defining functionals for single technologies, packages integrating multi-technologies, and mini-systems such as regions implementing industrial symbiosis. Based on the model, the combinations of technologies on both energy supply and demand sides can be addressed considering not only the societal scenarios such as resource prices, economic growth and population change but also the technical scenarios including the development and penetration of energy-related technologies such as distributed solid oxide fuel cells in residential sectors and new-generation vehicles, and the replacement and shift of current technologies such as heat pumps for air conditioning and centralized power generation. The developed model consists of two main modules; namely, a power generation dispatching module for the

  8. TEXACO GASIFICATION PROCESS - INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    This report summarizes the evaluation of the Texaco Gasification Process (TGP) conducted under the U.S. Environmental Protection Agency (EPA) Superfund Innovative Technology Evaluation (SITE) Program. The Texaco Gasification Process was developed by Texaco Inc. The TGP is a comm...

  9. Laser Processing Technology using Metal Powders

    International Nuclear Information System (INIS)

    Jang, Jeong-Hwan; Moon, Young-Hoon

    2012-01-01

    The purpose of this paper is to review the state of laser processing technology using metal powders. In recent years, a series of research and development efforts have been undertaken worldwide to develop laser processing technologies to fabricate metal-based parts. Layered manufacturing by the laser melting process is gaining ground for use in manufacturing rapid prototypes (RP), tools (RT) and functional end products. Selective laser sintering / melting (SLS/SLM) is one of the most rapidly growing rapid prototyping techniques. This is mainly due to the processes's suitability for almost any materials, including polymers, metals, ceramics and many types of composites. The interaction between the laser beam and the powder material used in the laser melting process is one of the dominant phenomena defining feasibility and quality. In the case of SLS, the powder is not fully melted during laser scanning, therefore the SLS-processed parts are not fully dense and have relatively low strength. To overcome this disadvantage, SLM and laser cladding (LC) processes have been used to enable full melting of the powder. Further studies on the laser processing technology will be continued due to the many potential applications that the technology offers.

  10. ADEPT2 - Next Generation Process Management Technology

    NARCIS (Netherlands)

    Dadam, P.; Rinderle, S.B.; Reichert, M.U.; Jurisch, M.; Acker, H.; Göser, K.; Kreher, U; Lauer, M.

    If current process management systems shall be applied to a broad spectrum of applications, they will have to be significantly improved with respect to their technological capabilities. In particular, in dynamic environments it must be possible to quickly implement and deploy new processes, to

  11. Optimization of processing technology of Rhizoma Pinelliae ...

    African Journals Online (AJOL)

    Methods: Orthogonal design method was applied to analyze the effects of factors such as licorice concentration volume, soaking time and processing temperature on processing technology of Rhizoma Pinelliae Praeparatum; MTT assay and flow cytometry were used to determine the inhibitory effect of Rhizoma Pinelliae ...

  12. Membrane technology in chemical process industry

    International Nuclear Information System (INIS)

    Bhattacharjee, B.

    2002-01-01

    The technology developments in current century will mainly focus on the energy, safe and effective utilization of available natural resources and environment. Production and effective use of water resource at industrial level will directly affect the environment. Similarly the various means of energy production and its consumption will also bear a direct impact on environment. In any chemical industry a large portion of energy consumption goes to separation process which in turn affect the cost of production as well as total cost of the plant. Therefore, minimization of energy consumption, finding out new nondestructive separation technology and reutilization of all recovered process streams are the new thrust area for chemical industries. In view of this, a comparatively new separation technology, 'Membrane Science and Technology' is available to the chemical industry. The potential of this technology is immense because of its simple operation, less chemical additives requirement, less energy consumption and easy adoptability to the existing process. This technology is often considered as energy efficient, environmentally benign and clean technology

  13. Future electricity generation: An economic and environmental life cycle perspective on near-, mid- and long-term technology options and policy implications

    Science.gov (United States)

    Bergerson, Joule Andrea

    This thesis evaluates the cost and environmental tradeoffs of current and future electricity generation options from a life cycle perspective. Policy and technology options are considered for each critical time horizon (near-, mid-, and long-term). The framework developed for this analysis is a hybrid life cycle analysis which integrates several models and frameworks including process and input-output life cycle analysis, an integrated environmental control model, social costing, forecasting and future energy scenario analysis. The near-term analysis shows that several recent LCA studies of electricity options have contributed to our understanding of the technologies available and their relative environmental impacts. Several promising options could satisfy our electricity demands. Other options remain unproven or too costly to encourage investment in the near term but show promise for future use (e.g. photovoltaic, fuel cells). Public concerns could impede the use of some desirable technologies (e.g. hydro, nuclear). Finally, less tangible issues such as intermittency of some renewable technologies, social equity and visual and land use impacts, while difficult to quantify, must be considered in the investment decision process. In the mid-term analysis, this thesis explores alternative methods for transport of coal energy. A hybrid life cycle analysis is critical for evaluating the cost, efficiency and environmental tradeoffs of the entire system. If a small amount of additional coal is to be shipped, current rail infrastructure should be used where possible. If entirely new infrastructure is required, the mine mouth generation options are cheaper but have increased environmental impact due to the increased generation required to compensate for transmission line losses. Gasifying the coal to produce methane also shows promise in terms of lowering environmental emissions. The long-term analysis focuses on the implications of a high coal use future. This scenario

  14. Power System Options Evaluated for the Radiation and Technology Demonstration Mission

    Science.gov (United States)

    Kerslake, Thomas W.; Benson, Scott W.

    2000-01-01

    The Radiation and Technology Demonstration (RTD) Mission is under joint study by three NASA Centers: the NASA Johnson Space Center, the NASA Goddard Space Flight Center, and the NASA Glenn Research Center at Lewis Field. This Earth-orbiting mission, which may launch on a space shuttle in the first half of the next decade, has the primary objective of demonstrating high-power electric thruster technologies. Secondary objectives include better characterization of Earth's Van Allen trapped-radiation belts, measurement of the effectiveness of the radiation shielding for human protection, measurement of radiation effects on advanced solar cells, and demonstration of radiation-tolerant microelectronics. During the mission, which may continue up to 1 year, the 2000-kg RTD spacecraft will first spiral outward from the shuttle-deployed, medium-inclination, low Earth orbit. By the phased operation of a 10-kW Hall thruster and a 10-kW Variable Specific Impulse Magneto-Plasma Rocket, the RTD spacecraft will reach a low-inclination Earth orbit with a radius greater than five Earth radii. This will be followed by an inward spiraling orbit phase when the spacecraft deploys 8 to 12 microsatellites to map the Van Allen belts. The mission will conclude in low Earth orbit with the possible retrieval of the spacecraft by the space shuttle. A conceptual RTD spacecraft design showing two photovoltaic (PV) array wings, the Hall thruster with propellant tanks, and stowed microsatellites is presented. Early power system studies assessed five different PV array design options coupled with a 120-Vdc power management and distribution system (PMAD) and secondary lithium battery energy storage. Array options include (1) state-of-the-art 10-percent efficient three-junction amorphous SiGe thin-film cells on thin polymer panels deployed with an inflatable (or articulated) truss, (2) SCARLET array panels, (3) commercial state-of-the-art, planar PV array rigid panels with 25-percent efficient, three

  15. Environmental and technology policy options in the electricity sector. Interactions and outcomes

    International Nuclear Information System (INIS)

    Fischer, Carolyn; Newell, Richard G.; Preonas, Louis

    2014-01-01

    Myriad policy measures aim to reduce greenhouse gas emissions from the electricity sector, promote generation from renewable sources, and encourage energy conservation. To what extent do innovation and energy efficiency (EE) market failures justify additional interventions when a carbon price is in place? We extend the model of Fischer and Newell (2008) with advanced and conventional renewable energy technologies and short and long-run EE investments. We incorporate both knowledge spillovers and imperfections in the demand for energy efficiency. We conclude that some technology policies, particularly correcting R and D market failures, can be useful complements to emissions pricing, but ambitious renewable targets or subsidies seem unlikely to enhance welfare when placed alongside sufficient emissions pricing. The desirability of stringent EE policies is highly sensitive to the degree of undervaluation of EE by consumers, which also has implications for policies that tend to lower electricity prices. Even with multiple market failures, emissions pricing remains the single most cost-effective option for reducing emissions.

  16. Green micro-resistojet research at Delft University of Technology: new options for Cubesat propulsion

    Science.gov (United States)

    Cervone, A.; Zandbergen, B.; Guerrieri, D. C.; De Athayde Costa e Silva, M.; Krusharev, I.; van Zeijl, H.

    2017-03-01

    The aerospace industry is recently expressing a growing interest in green, safe and non-toxic propellants for the propulsion systems of the new generation of space vehicles, which is especially true in the case of Cubesat micro-propulsion systems. Demanding requirements are associated to the future missions and challenges offered by this class of spacecraft, where the availability of a propulsion system might open new possibilities for a wide range of applications including orbital maintenance and transfer, formation flying and attitude control. To accomplish these requirements, Delft University of Technology is currently developing two different concepts of water-propelled micro-thrusters based on MEMS technologies: a free molecular micro-resistojet operating with sublimating solid water (ice) at low plenum gas pressure of less than 600 Pa, and a more conventional micro-resistojet operating with liquid water heated and vaporized by means of a custom designed silicon heating chamber. In this status review paper, the current design and future expected developments of the two micro-propulsion concepts is presented and discussed, together with an initial analysis of the expected performance and potential operational issues. Results of numerical simulations conducted to optimize the design of the heating and expansion slots, as well as a detailed description of the manufacturing steps for the conventional micro-resistojet concept, are presented. Some intended steps for future research activities, including options for thrust intensity and direction control, are briefly introduced.

  17. Choices of capture chromatography technology in antibody manufacturing processes.

    Science.gov (United States)

    DiLeo, Michael; Ley, Arthur; Nixon, Andrew E; Chen, Jie

    2017-11-15

    The capture process employed in monoclonal antibody downstream purification is not only the most critically impacted process by increased antibody titer resulting from optimized mammalian cell culture expression systems, but also the most important purification step in determining overall process throughput, product quality, and economics. Advances in separation technology for capturing antibodies from complex feedstocks have been one focus of downstream purification process innovation for past 10 years. In this study, we evaluated new generation chromatography resins used in the antibody capture process including Protein A, cation exchange, and mixed mode chromatography to address the benefits and unique challenges posed by each chromatography approach. Our results demonstrate the benefit of improved binding capacity of new generation Protein A resins, address the concern of high concentration surge caused aggregation when using new generation cation exchange resins with over 100mg/mL binding capacity, and highlight the potential of multimodal cation exchange resins for capture process design. The new landscape of capture chromatography technologies provides options to achieve overall downstream purification outcome with high product quality and process efficiency. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Business process modeling for processing classified documents using RFID technology

    Directory of Open Access Journals (Sweden)

    Koszela Jarosław

    2016-01-01

    Full Text Available The article outlines the application of the processing approach to the functional description of the designed IT system supporting the operations of the secret office, which processes classified documents. The article describes the application of the method of incremental modeling of business processes according to the BPMN model to the description of the processes currently implemented (“as is” in a manual manner and target processes (“to be”, using the RFID technology for the purpose of their automation. Additionally, the examples of applying the method of structural and dynamic analysis of the processes (process simulation to verify their correctness and efficiency were presented. The extension of the process analysis method is a possibility of applying the warehouse of processes and process mining methods.

  19. American option valuation under time changed tempered stable Lévy processes

    Science.gov (United States)

    Gong, Xiaoli; Zhuang, Xintian

    2017-01-01

    Given that the underlying assets in financial markets exhibit stylized facts such as leptokurtosis, asymmetry, clustering properties and heteroskedasticity effect, this paper presents a novel model for pricing American option under the assumptions that the stock price processes are governed by time changed tempered stable Lévy process. As this model is constructed by introducing random time changes into tempered stable (TS) processes which specially refer to normal tempered stable (NTS) distribution as well as classical tempered stable (CTS) distribution, it permits infinite jumps as well as capturing random varying time in stochastic volatility, consequently taking into account the empirical facts such as leptokurtosis, skewness and volatility clustering behaviors. We employ the Fourier-cosine technique to calculate American option and propose the improved Particle Swarm optimization (IPSO) intelligent algorithm for model calibration. To demonstrate the advantage of the constructed model, we carry out empirical research on American index option in financial markets across wide ranges of models, with the time changing normal tempered stable distribution model yielding a superior performance than others.

  20. Advanced Reactor Technology Options for Utilization and Transmutation of Actinides in Spent Nuclear Fuel

    International Nuclear Information System (INIS)

    2009-09-01

    Renewed interest in the potential of nuclear energy to contribute to a sustainable worldwide energy mix is strengthening the IAEA's statutory role in fostering the peaceful uses of nuclear energy, in particular the need for effective exchanges of information and collaborative research and technology development among Member States on advanced nuclear power technologies (Articles III-A.1 and III-A.3). The major challenges facing the long term development of nuclear energy as a part of the world's energy mix are improvement of the economic competitiveness, meeting increasingly stringent safety requirements, adhering to the criteria of sustainable development, and public acceptability. The concern linked to the long life of many of the radioisotopes generated from fission has led to increased R and D efforts to develop a technology aimed at reducing the amount of long lived radioactive waste through transmutation in fission reactors or accelerator driven hybrids. In recent years, in various countries and at an international level, more and more studies have been carried out on advanced and innovative waste management strategies (i.e. actinide separation and elimination). Within the framework of the Project on Technology Advances in Fast Reactors and Accelerator Driven Systems (http://www.iaea.org/inisnkm/nkm/aws/fnss/index.html), the IAEA initiated a number of activities on utilization of plutonium and transmutation of long lived radioactive waste, accelerator driven systems, thorium fuel options, innovative nuclear reactors and fuel cycles, non-conventional nuclear energy systems, and fusion/fission hybrids. These activities are implemented under the guidance and with the support of the IAEA Nuclear Energy Department's Technical Working Group on Fast Reactors (TWG-FR). This publication compiles the analyses and findings of the Coordinated Research Project (CRP) on Studies of Advanced Reactor Technology Options for Effective Incineration of Radioactive Waste (2002

  1. Manufacturing technology and process for BWR fuel

    International Nuclear Information System (INIS)

    Kato, Shigeru

    1996-01-01

    Following recent advanced technologies, processes and requests of the design changes of BWR fuel, Nuclear Fuel Industries, Ltd. (NFI) has upgraded the manufacturing technology and honed its own skills to complete its brand-new automated facility in Tokai in the latter half of 1980's. The plant uses various forms of automation throughout the manufacturing process: the acceptance of uranium dioxide powder, pelletizing, fuel rod assembling, fuel bundle assembling and shipment. All processes are well computerized and linked together to establish the integrated control system with three levels of Production and Quality Control, Process Control and Process Automation. This multi-level system plays an important role in the quality assurance system which generates the highest quality of fuels and other benefits. (author)

  2. Fluidization technologies: Aerodynamic principles and process engineering.

    Science.gov (United States)

    Dixit, Rahul; Puthli, Shivanand

    2009-11-01

    The concept of fluidization has been adapted to different unit processes of pharmaceutical product development. Till date a lot of improvements have been made in the engineering design to achieve superior process performance. This review is focused on the fundamental principles of aerodynamics and hydrodynamics associated with the fluidization technologies. Fluid-bed coating, fluidized bed granulation, rotor processing, hot melt granulation, electrostatic coating, supercritical fluid based fluidized bed technology are highlighted. Developments in the design of processing equipments have been explicitly elucidated. This article also discusses processing problems from the operator's perspective along with latest developments in the application of these principles. (c) 2009 Wiley-Liss, Inc. and the American Pharmacists Association

  3. Biofuels development in China: Technology options and policies needed to meet the 2020 target

    International Nuclear Information System (INIS)

    Chang, Shiyan; Zhao, Lili; Timilsina, Govinda R.; Zhang, Xiliang

    2012-01-01

    China promulgated the Medium and Long-Term Development Plan for Renewable Energy in 2007, which included sub-targets of 2010 and 2020 for various renewable energy technologies. Almost all the 2010 sub-targets have been met and even surpassed except non-grain fuel ethanol. There is debate surrounding the questions of whether and how the country will be able to meet the 2020 biofuels target. This paper provides the assessment of potential technology pathways to achieve the 2020 target regarding their respective resource potential and supply cost. Barriers and policy options are identified based on broad literatures review. And an overview of biofuels projections is presented to provide insight into the comparison of various policy scenarios. The study shows that China can potentially satisfy non-grain fuel ethanol target by 2020 from technology perspective. But she will probably fall far short of this target if current situations continue. Additional policy efforts are needed. Meanwhile, the target of biodiesel production has high probability to be achieved. However, if given support policies, it will develop better. - Highlights: ► I. Non-grain feedstocks such as cassava, sweet sorghum and sweet potato grown in low productive arable lands or unutilized lands have enough potential to meet ethanol targets in 2020. ► II. If current situations continue, China will fall far short of the 2020 target. ► III. The target of biodiesel production has high probability to be achieved, while, if given support policies, it will develop better. ► IV. Supply cost is one of the major barriers faced by all biofuels pathways. ► V. Various policy measures would be necessary to overcome the costs barriers to biofuels in China.

  4. Image processing technology for nuclear facilities

    International Nuclear Information System (INIS)

    Lee, Jong Min; Lee, Yong Beom; Kim, Woong Ki; Park, Soon Young

    1993-05-01

    Digital image processing technique is being actively studied since microprocessors and semiconductor memory devices have been developed in 1960's. Now image processing board for personal computer as well as image processing system for workstation is developed and widely applied to medical science, military, remote inspection, and nuclear industry. Image processing technology which provides computer system with vision ability not only recognizes nonobvious information but processes large information and therefore this technique is applied to various fields like remote measurement, object recognition and decision in adverse environment, and analysis of X-ray penetration image in nuclear facilities. In this report, various applications of image processing to nuclear facilities are examined, and image processing techniques are also analysed with the view of proposing the ideas for future applications. (Author)

  5. BUSINESS PROCESS MANAGEMENT SYSTEMS TECHNOLOGY COMPONENTS ANALYSIS

    Directory of Open Access Journals (Sweden)

    Andrea Giovanni Spelta

    2007-05-01

    Full Text Available The information technology that supports the implementation of the business process management appproach is called Business Process Management System (BPMS. The main components of the BPMS solution framework are process definition repository, process instances repository, transaction manager, conectors framework, process engine and middleware. In this paper we define and characterize the role and importance of the components of BPMS's framework. The research method adopted was the case study, through the analysis of the implementation of the BPMS solution in an insurance company called Chubb do Brasil. In the case study, the process "Manage Coinsured Events"" is described and characterized, as well as the components of the BPMS solution adopted and implemented by Chubb do Brasil for managing this process.

  6. Exploring novel food proteins and processing technologies

    NARCIS (Netherlands)

    Avila Ruiz, Geraldine

    2016-01-01

    Foods rich in protein are nowadays high in demand worldwide. To ensure a sustainable supply and a high quality of protein foods, novel food proteins and processing technologies need to be explored to understand whether they can be used for the development of high-quality protein foods. Therefore,

  7. Improvisation during Process-Technology Adoption

    DEFF Research Database (Denmark)

    Tjørnehøj, Gitte; Mathiassen, Lars

    2010-01-01

    Most software firms struggle to take advantage of the potential benefits of software process improvement (SPI) as they adopt this technology into the complex and dynamic realities of their day-to-day operation. Such efforts are therefore typically fluctuating between management's attempt to contr...

  8. Influence Processes for Information Technology Acceptance

    DEFF Research Database (Denmark)

    Bhattacherjee, Anol; Sanford, Clive Carlton

    2006-01-01

    This study examines how processes of external influence shape information technology acceptance among potential users, how such influence effects vary across a user population, and whether these effects are persistent over time. Drawing on the elaboration-likelihood model (ELM), we compared two...

  9. Development of Food Preservation and Processing Technologies by Radiation Technology

    International Nuclear Information System (INIS)

    Byun, Myung Woo; Lee, Ju Won; Kim, Jae Hun

    2007-07-01

    To secure national food resources, development of energy-saving food processing and preservation technologies, establishment of method on improvement of national health and safety by development of alternative techniques of chemicals and foundation of the production of hygienic food and public health related products by irradiation technology were studied. Results at current stage are following: As the first cooperative venture business technically invested by National Atomic Research Development Project, institute/company's [technology-invested technology foundation No. 1] cooperative venture, Sun-BioTech Ltd., was founded and stated its business. This suggested new model for commercialization and industrialization of the research product by nation-found institute. From the notice of newly approved product list about irradiated food, radiation health related legal approval on 7 food items was achieved from the Ministry of health and wellfare, the Korea Food and Drug Administration, and this contributed the foundation of enlargement of practical use of irradiated food. As one of the foundation project for activation of radiation application technology for the sanitation and secure preservation of special food, such as military meal service, food service for patient, and food for sports, and instant food, such as ready-to-eat/ready-to-cook food, the proposal for radiation application to the major military commander at the Ministry of National Defence and the Joint Chiefs of Staff was accepted for the direction of military supply development in mid-termed plan for the development of war supply. Especially, through the preliminary research and the development of foundation technology for the development of the Korean style space food and functional space food, space Kimch with very long shelf life was finally developed. The development of new item/products for food and life science by combining RT/BT, the development of technology for the elimination/reduction of

  10. Development of Food Preservation and Processing Technologies by Radiation Technology

    Energy Technology Data Exchange (ETDEWEB)

    Byun, Myung Woo; Lee, Ju Won; Kim, Jae Hun (and others)

    2007-07-15

    To secure national food resources, development of energy-saving food processing and preservation technologies, establishment of method on improvement of national health and safety by development of alternative techniques of chemicals and foundation of the production of hygienic food and public health related products by irradiation technology were studied. Results at current stage are following: As the first cooperative venture business technically invested by National Atomic Research Development Project, institute/company's [technology-invested technology foundation No. 1] cooperative venture, Sun-BioTech Ltd., was founded and stated its business. This suggested new model for commercialization and industrialization of the research product by nation-found institute. From the notice of newly approved product list about irradiated food, radiation health related legal approval on 7 food items was achieved from the Ministry of health and wellfare, the Korea Food and Drug Administration, and this contributed the foundation of enlargement of practical use of irradiated food. As one of the foundation project for activation of radiation application technology for the sanitation and secure preservation of special food, such as military meal service, food service for patient, and food for sports, and instant food, such as ready-to-eat/ready-to-cook food, the proposal for radiation application to the major military commander at the Ministry of National Defence and the Joint Chiefs of Staff was accepted for the direction of military supply development in mid-termed plan for the development of war supply. Especially, through the preliminary research and the development of foundation technology for the development of the Korean style space food and functional space food, space Kimch with very long shelf life was finally developed. The development of new item/products for food and life science by combining RT/BT, the development of technology for the elimination/reduction of

  11. Renewable energy technology (RET) options for supplying energy in a post disaster recovery situation

    Energy Technology Data Exchange (ETDEWEB)

    Nigim, K.; Uddin Amed, F.; Reiser, H. [Lambton College, Sarnia, ON (Canada). School of Technology, Applied Science, Fire Science and Apprenticeship

    2010-07-01

    In most places, electricity is produced in a centralized power generating plant and distributed to consumer load centers by transmission lines. In a wide scale devastation of the electrical supply and delivery system, a complete rebuilding is inevitable. This paper discussed how post disaster electricity demand can be met and how electricity can be supplied when all conventional options are out of consideration. Medical, water purification and communication facilities require a source of energy for their operation and must be powered immediately following a disaster. Small dispersed conventional fuel generating units offer an intermediate solution. However, if the fuel transportation infrastructure is not restored, then many of the generating units will be idle. This paper focused on how renewable energy technologies (RETs) can be used to supply power to meet basic rescue equipment demand during the recovery phase of a completely devastated electricity supply infrastructure. Different RETs that can be used to supply the demand were also examined and compared with conventional emergency generating units. The challenges and constraints of using RET were also discussed along with some RET systems that can be adopted for successful and effective use of RET in a post disaster situation. It was concluded that investment in RET systems will contribute to the long-term economic recovery, environment and energy use because RET systems reduce dependency on fossil fuels and contribute to a reduction in greenhouse gas emissions. 10 refs., 4 tabs., 2 figs.

  12. 2005 resource options report

    International Nuclear Information System (INIS)

    Morris, T.

    2005-01-01

    This resource options report (ROR) fulfils regulatory requirements in British Columbia's two-year resource planning process. It identifies a wide range of resources and technologies that could be used to meet BC Hydro's future electricity demand. As such, it facilitates a transparent public review of resource options which include both supply-side and demand-side options. The resource options that will be used in the 2005 integrated electricity plan (IEP) were characterized. This ROR also documents where there is a general agreement or disagreement on the resource type characterization, based on the First Nations and Stakeholder engagement. BC Hydro used current information to provide realistic ranges on volume and cost to characterize environmental and social attributes. The BC Hydro system was modelled to assess the benefit and cost of various resource options. The information resulting from this ROR and IEP will help in making decisions on how to structure competitive acquisition calls and to determine the level of transmission services needed to advance certain BC Hydro projects. The IEP forecasts the nature and quantity of domestic resources required over the next 20 years. A strategic direction on how those needs will be met has been created to guide the management of BC Hydro's energy resources. Supply-side options include near-commercial technologies such as energy storage, ocean waves, tidal, fuel cells and integrated coal gasification combined cycle technology. Supply-side options also include natural gas, coal, biomass, geothermal, wind, and hydro. 120 refs., 39 tabs., 21 figs., 6 appendices

  13. Improving drug manufacturing with process analytical technology.

    Science.gov (United States)

    Rodrigues, Licinia O; Alves, Teresa P; Cardoso, Joaquim P; Menezes, José C

    2006-01-01

    Within the process analytical technology (PAT) framework, as presented in the US Food and Drug Administration guidelines, the aim is to design, develop and operate processes consistently to ensure a pre-defined level of quality at the end of the manufacturing process. Three PAT implementation scenarios can be envisaged. Firstly, PAT could be used in its most modest version (in an almost non-PAT manner) to simply replace an existing quality control protocol (eg, using near-infrared spectroscopy for an in-process quality control, such as moisture content). Secondly, the use of in-process monitoring and process analysis could be integrated to enhance process understanding and operation for an existing industrial process. Thirdly, PAT could be used extensively and exclusively throughout development, scale-up and full-scale production of a new product and process. Although the first type of implementations are well known, reports of the second and third types remain scarce. Herein, results obtained from PAT implementations of the second and third types are described for two industrial processes for preparing bulk active pharmaceutical ingredients, demonstrating the benefits in terms of increased process understanding and process control.

  14. Energy conversion technology by chemical processes

    Energy Technology Data Exchange (ETDEWEB)

    Oh, I.W.; Yoon, K.S.; Cho, B.W. [Korea Inst. of Science and Technology, Seoul (Korea, Republic of)] [and others

    1996-12-01

    The sharp increase in energy usage according to the industry development has resulted in deficiency of energy resources and severe pollution problems. Therefore, development of the effective way of energy usage and energy resources of low pollution is needed. Development of the energy conversion technology by chemical processes is also indispensable, which will replace the pollutant-producing and inefficient mechanical energy conversion technologies. Energy conversion technology by chemical processes directly converts chemical energy to electrical one, or converts heat energy to chemical one followed by heat storage. The technology includes batteries, fuel cells, and energy storage system. The are still many problems on performance, safety, and manufacturing of the secondary battery which is highly demanded in electronics, communication, and computer industries. To overcome these problems, key components such as carbon electrode, metal oxide electrode, and solid polymer electrolyte are developed in this study, followed by the fabrication of the lithium secondary battery. Polymer electrolyte fuel cell, as an advanced power generating apparatus with high efficiency, no pollution, and no noise, has many applications such as zero-emission vehicles, on-site power plants, and military purposes. After fabricating the cell components and operating the single cells, the fundamental technologies in polymer electrolyte fuel cell are established in this study. Energy storage technology provides the safe and regular heat energy, irrespective of the change of the heat energy sources, adjusts time gap between consumption and supply, and upgrades and concentrates low grade heat energy. In this study, useful chemical reactions for efficient storage and transport are investigated and the chemical heat storage technology are developed. (author) 41 refs., 90 figs., 20 tabs.

  15. Finite difference methods for option pricing under Lévy processes: Wiener-Hopf factorization approach.

    Science.gov (United States)

    Kudryavtsev, Oleg

    2013-01-01

    In the paper, we consider the problem of pricing options in wide classes of Lévy processes. We propose a general approach to the numerical methods based on a finite difference approximation for the generalized Black-Scholes equation. The goal of the paper is to incorporate the Wiener-Hopf factorization into finite difference methods for pricing options in Lévy models with jumps. The method is applicable for pricing barrier and American options. The pricing problem is reduced to the sequence of linear algebraic systems with a dense Toeplitz matrix; then the Wiener-Hopf factorization method is applied. We give an important probabilistic interpretation based on the infinitely divisible distributions theory to the Laurent operators in the correspondent factorization identity. Notice that our algorithm has the same complexity as the ones which use the explicit-implicit scheme, with a tridiagonal matrix. However, our method is more accurate. We support the advantage of the new method in terms of accuracy and convergence by using numerical experiments.

  16. Cost-effective and low-technology options for simulation and training in neonatology.

    Science.gov (United States)

    Bruno, Christie J; Glass, Kristen M

    2016-11-01

    The purpose of this review is to explore low-cost options for simulation and training in neonatology. Numerous cost-effective options exist for simulation and training in neonatology. Lower cost options are available for teaching clinical skills and procedural training in neonatal intubation, chest tube insertion, and pericardiocentesis, among others. Cost-effective, low-cost options for simulation-based education can be developed and shared in order to optimize the neonatal simulation training experience. Copyright © 2016 Elsevier Inc. All rights reserved.

  17. Improvisation during Process-Technology Adoption

    DEFF Research Database (Denmark)

    Tjørnehøj, Gitte; Mathiassen, Lars

    2010-01-01

    firm, SmallSoft, over a 10-year period (1996–2005). We found that micro-level and macro-level improvisations interacted, often in uncoordinated ways, to shape SPI technology adoption at SmallSoft. The improvisations enhanced employee creativity, motivation and empowerment, created momentum......Most software firms struggle to take advantage of the potential benefits of software process improvement (SPI) as they adopt this technology into the complex and dynamic realities of their day-to-day operation. Such efforts are therefore typically fluctuating between management's attempt to control...

  18. Process Technology for Immobilized Lipasecatalyzed Reactions

    DEFF Research Database (Denmark)

    Xu, Yuan

    (e.g. a hydrophobic carrier for the immobilized lipase and the capabilities to provide sufficient mixing as well as stepwise/continuous feeding of ethanol to the reactor). An STR is efficient for batch operation while a PBR is efficient for a continuous production. An STR can more easily provide...... sufficient external mass transfer for a reaction, but will lead to more mechanical damage of the biocatalyst particles, than a PBR. A reactor combination of CSTR with PBR can couple the advantages of both, delivering an efficient continuous process. The second case study (esterification) shares some similar......-catalyzed transesterification is that it is multi-phasic system. The by-product glycerol can potentially impose inhibitory effects on immobilized lipases and likewise the un-dissolved ethanol can inhibit the lipase. The options for addressing these issues can be used as the basis for selecting the biocatalyst and the reactor...

  19. Pricing of American Put Option under a Jump Diffusion Process with Stochastic Volatility in an Incomplete Market

    Directory of Open Access Journals (Sweden)

    Shuang Li

    2014-01-01

    Full Text Available We study the pricing of American options in an incomplete market in which the dynamics of the underlying risky asset is driven by a jump diffusion process with stochastic volatility. By employing a risk-minimization criterion, we obtain the Radon-Nikodym derivative for the minimal martingale measure and consequently a linear complementarity problem (LCP for American option price. An iterative method is then established to solve the LCP problem for American put option price. Our numerical results show that the model and numerical scheme are robust in capturing the feature of incomplete finance market, particularly the influence of market volatility on the price of American options.

  20. EVALUATION OF POLLUTION PREVENTION OPTIONS TO REDUCE STYRENE EMISSIONS FROM FIBER-REINFORCED PLASTIC OPEN MOLDING PROCESSES

    Science.gov (United States)

    Pollution prevention (P2) options to reduce styrene emissions, such as new materials, and application equipment, are commercially available to the operators of open molding processes. However, information is lacking on the emissions reduction that these options can achieve. To me...

  1. Control of processes using isotopic diagnostic's technologies

    International Nuclear Information System (INIS)

    Vargas, Celso; Chaverri, Oscar; Chine, Bruno; Conejo, Mario

    2005-01-01

    The Escuela de Ciencias e Ingenieria de los Materiales of the Instituto Tecnologico de Costa Rica, in cooperation with OIEA, develops a project of dowry of capacity oriented to the formation of professionals and equipment for the use of two important technologies of isotopic diagnostic. The first of them is the technology of tracers that operates the unique properties that present different radioactive isotopics like open sources. The second one well known as scanning or profile gamma, uses sealed source, of the some nature that the previous ones, to obtain profiles in different processes and thus to determine its internal condition and operation. The objective of this article is to present both technologies, its benefits and to promote the use in the country [es

  2. Pricing foreign equity option under stochastic volatility tempered stable Lévy processes

    Science.gov (United States)

    Gong, Xiaoli; Zhuang, Xintian

    2017-10-01

    Considering that financial assets returns exhibit leptokurtosis, asymmetry properties as well as clustering and heteroskedasticity effect, this paper substitutes the logarithm normal jumps in Heston stochastic volatility model by the classical tempered stable (CTS) distribution and normal tempered stable (NTS) distribution to construct stochastic volatility tempered stable Lévy processes (TSSV) model. The TSSV model framework permits infinite activity jump behaviors of return dynamics and time varying volatility consistently observed in financial markets through subordinating tempered stable process to stochastic volatility process, capturing leptokurtosis, fat tailedness and asymmetry features of returns. By employing the analytical characteristic function and fast Fourier transform (FFT) technique, the formula for probability density function (PDF) of TSSV returns is derived, making the analytical formula for foreign equity option (FEO) pricing available. High frequency financial returns data are employed to verify the effectiveness of proposed models in reflecting the stylized facts of financial markets. Numerical analysis is performed to investigate the relationship between the corresponding parameters and the implied volatility of foreign equity option.

  3. Process options and projected mass flows for the HTGR refabrication scrap recovery system

    International Nuclear Information System (INIS)

    Tiegs, S.M.

    1979-03-01

    The two major uranium recovery processing options reviewed are (1) internal recovery of the scrap by the refabrication system and (2) transfer to and external recovery of the scrap by the head end of the reprocessing system. Each option was reviewed with respect to equipment requirements, preparatory processing, and material accountability. Because there may be a high cost factor on transfer of scrap fuel material to the reprocessing system for recovery, all of the scrap streams will be recycled internally within the refabrication system, with the exception of reject fuel elements, which will be transferred to the head end of the reprocessing system for uranium recovery. The refabrication facility will be fully remote; thus, simple recovery techniques were selected as the reference processes for scrap recovery. Crushing, burning, and leaching methods will be used to recover uranium from the HTGR refabrication scrap fuel forms, which include particles without silicon carbide coatings, particles with silicon carbide coatings, uncarbonized fuel rods, carbon furnace parts, perchloroethylene distillation bottoms, and analytical sample remnants. Mass flows through the reference scrap recovery system were calculated for the HTGR reference recycle facility operating with the highly enriched uranium fuel cycle. Output per day from the refabrication scrap recovery system is estimated to be 4.02 kg of 2355 U and 10.85 kg of 233 U. Maximum equipment capacities were determined, and future work will be directed toward the development and costing of the scrap recovery system chosen as reference

  4. Waste processing building with incineration technology

    Science.gov (United States)

    Wasilah, Wasilah; Zaldi Suradin, Muh.

    2017-12-01

    In Indonesia, waste problem is one of major problem of the society in the city as part of their life dynamics. Based on Regional Medium Term Development Plan of South Sulawesi Province in 2013-2018, total volume and waste production from Makassar City, Maros, Gowa, and Takalar Regency estimates the garbage dump level 9,076.949 m3/person/day. Additionally, aim of this design is to present a recommendation on waste processing facility design that would accommodate waste processing process activity by incineration technology and supported by supporting activity such as place of education and research on waste, and the administration activity on waste processing facility. Implementation of incineration technology would reduce waste volume up to 90% followed by relative negative impact possibility. The result planning is in form of landscape layout that inspired from the observation analysis of satellite image line pattern of planning site and then created as a building site pattern. Consideration of building orientation conducted by wind analysis process and sun path by auto desk project Vasari software. The footprint designed by separate circulation system between waste management facility interest and the social visiting activity in order to minimize the croos and thus bring convenient to the building user. Building mass designed by inseparable connection series system, from the main building that located in the Northward, then connected to a centre visitor area lengthways, and walked to the waste processing area into the residue area in the Southward area.

  5. The Plasma Hearth Process Technology Development Project

    International Nuclear Information System (INIS)

    Geimer, R.; Batdorf, J.; Wolfe, P.

    1993-01-01

    The US DOE Office of Technology Development (OTD) is currently evaluating the Plasma Hearth Process (PHP) for potential treatment of several DOE waste types. The PHP is a high-temperature vitrification process that has potential application for a wide range of mixed waste types in both the low-level and transuranic mixed waste categories. The PHP is being tested under both the OTD Mixed Waste Integrated Program and the Buried Waste Integrated Demonstration. Initial testing has been completed on several different surrogate waste forms that are representative of some of the DOE mixed waste streams. Destruction of organic material exceeds that of conventional incineration technologies. The vitrified residual has leaching characteristics comparable to glass formulations produced in the high-level waste program. The first phase of the PHP demonstration project has been successfully completed, and the project is currently beginning a comprehensive second phase of development and testing

  6. Assessment of coal technology options and implications for the State of Hawaii

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, J.L.; Elcock, D.; Elliott, T.J. [and others

    1993-12-01

    The mandate of this research report was to provide the state of Hawaii with an assessment of the potential opportunities and drawbacks of relying on coal-fired generating technologies to diversify its fuel mix and satisfy future electric power requirements. This assessment was to include a review of existing and emerging coal-based power technologies-including their associated costs, environmental impacts, land use, and infrastructure requirements-to determine the range of impacts likely to occur if such systems were deployed in Hawaii. Coupled with this review, the report was also to (1) address siting and safety issues as they relate to technology choice and coal transport, (2) consider how environmental costs associated with coal usage are included in the integrated resource planning (ERP) process, and (3) develop an analytical tool from which the Department of Business, Economic Development & Tourism of the State of Hawaii could conduct first-order comparisons of power plant selection and siting. The prepared report addresses each element identified above. However, available resources and data limitations limited the extent to which particular characteristics of coal use could be assessed. For example, the technology profiles are current but not as complete regarding future developments and cost/emissions data as possible, and the assessment of coal technology deployment issues in Hawaii was conducted on an aggregate (not site-specific) basis. Nonetheless, the information and findings contained in this report do provide an accurate depiction of the opportunities for and issues associated with coal utilization in the state of Hawaii.

  7. Developing technological process of obtaining giality casts

    Directory of Open Access Journals (Sweden)

    A. Issagulov

    2014-10-01

    Full Text Available The article considers the process of manufacturing castings using sand-resin forms and alloying furnace. Were the optimal technological parameters of manufacturing shell molds for the manufacture of castings of heating equipment. Using the same upon receipt of castings by casting in shell molds furnace alloying and deoxidation of the metal will provide consumers with quality products and have a positive impact on the economy in general engineering.

  8. Similarity search processing. Paralelization and indexing technologies.

    Directory of Open Access Journals (Sweden)

    Eder Dos Santos

    2015-08-01

    The next Scientific-Technical Report addresses the similarity search and the implementation of metric structures on parallel environments. It also presents the state of the art related to similarity search on metric structures and parallelism technologies. Comparative analysis are also proposed, seeking to identify the behavior of a set of metric spaces and metric structures over processing platforms multicore-based and GPU-based.

  9. Design and optimization of sustainable process technologies

    DEFF Research Database (Denmark)

    Mussatto, Solange I.; Qin, Fen; Yamakawa, Celina Kiyomi

    The development of sustainable processes and innovative strategies that can accelerate the transition to a bio-economyis one of the main goals of the current societyin order to have a future less dependent on oil and with lower carbon emissions. The use of biomass as a feedstock for bioprocesses......, minimizing the costs and maximizing the efficiencyand productivity.Once the optimal conditions are identified, the process scale-up can be then evaluated. This could be translated in a faster time to market for newprocess technologies....

  10. Digital signal processing - growth of a technology

    International Nuclear Information System (INIS)

    Peek, J.B.H.

    1985-01-01

    The rapid development of microelectronics has led to an increasing extent in circuits and systems for digital signal processing. This happened first in professional applications, e.g. geophysics, astronomy and space flight, and now, with the Compact Disc player, these techniques have entered the consumer field. In the near future digital TV applications will undoubtedly follow. This article outlines a number of the developments behind the advancing 'digitization' of modern technology. The article also considers the main advantages and disadvantages of digital signal processing the main modules now used and some common applications. Particular attention is paid to medical applications. (Auth.)

  11. Radiation processing: a versatile technology for industry

    International Nuclear Information System (INIS)

    Cabalfin, E.G.

    1996-01-01

    Soon after the discovery of x-ray in 1895 and radioactivity in 1896, it was recognized that ionizing radiation can modify the chemical, physical and/or biological properties of materials. However, it was only in the late 50's, when large radiation sources become available, has this unique property of radiation found industrial applications in radiation processing. Today, radiation processing has been used by industry in such diverse applications, such as radiation sterilization/decontamination of medical products, pharmaceuticals, cosmetics and their raw materials; radiation cross-linking of wire and cable insulation; production of heat shrinkable materials and polymer foam; and radiation curing of coatings, adhesives and inks on a wide variety of substrates. In addition to being a clean environment-friendly technology, radiation processing can also be used for the conservation of the environment by such processes as radiation treatment of flue gases to remove SO 2 and NO x and disinfection of sewage sludge. Because of the many advantages offered by radiation processing, industry is showing strong interest in the technology as evidenced by the growing number of industrial radiation facilities in many countries. (author)

  12. The Search for New Information Processing technologies

    Science.gov (United States)

    Cavin, Ralph K.

    2005-03-01

    Our society has benefited from the ‘Golden Age of Electronics’ for the last half century. The ubiquitous transistor, in its many manifestations, has enabled an explosion of capabilities in information processing, communications, and sensing that has spurred exponential growth in performance-benefit ratios. Much of the credit for this progress is due to the continued scaling of the silicon integrated circuit (IC) components and to the associated efficient fabrication processes that have made the IC affordable. There is a growing realization, from simple physics arguments, that as minimum features sizes approach the ten nanometer regime, scaling will very likely slow and eventually end. This doesn’t mean that the MOSFET will disappear, but more likely that it will need to be supplemented by other device and interconnect technologies if the exponential gains are to continue. In this talk we discuss the basis for the projected limitation of scaling of charge-based devices for logic and memory devices. We argue that a fundamental consideration for all devices, including those based on charge, relates to the capacity to manage heat generated by circuit operation. Our preference is for devices that operate at room temperature since the energy costs for cooling the devices must also be charged against the overall system energy consumption. (Cooling costs increase as a power of the difference between the ambient and the target temperature.) Therefore we seek new state variables to serve as an alternative to electrical charge for future information processing technologies. These technologies must provide the potential for sustaining exponential performance-cost benefits with time. The search must not only focus on device structures but on the underlying materials and process technologies that enable these structures. Indeed, to obtain extremely scaled CMOS, new materials and processes must also be developed. In this talk, we survey some of the candidates for

  13. 99Mo/(99m)Tc separation: an assessment of technology options.

    Science.gov (United States)

    Dash, Ashutosh; Knapp, F F Russ; Pillai, M R A

    2013-02-01

    Several strategies for the effective separation of (99m)Tc from (99)Mo have been developed and validated. Due to the success of column chromatographic separation using acidic alumina coupled with high specific activity fission (99)Mo (F (99)Mo) for production of (99)Mo/(99m)Tc generators, however, most technologies until recently have generated little interest. The reduced availability of F (99)Mo and consequently the shortage of (99)Mo/(99m)Tc column generators in the recent past have resurrected interest in the production of (99)Mo as well as (99m)Tc by alternate routes. Most of these alternative production processes require separation techniques capable of providing clinical grade (99m)Tc from low specific activity (99)Mo or irradiated Mo targets. For this reason there has been renewed interest in alternate separation routes. This paper reviews the reported separation technologies which include column chromatography, solvent extraction, sublimation and gel systems that have been traditionally used for the fabrication of (99)Mo/(99m)Tc generator systems. The comparative advantage, disadvantage, and technical challenges toward adapting the emerging requirements are discussed. New developments such as solid-phase column extraction, electrochemical separation, extraction chromatography, supported liquid membrane (SLM) and thermochromatographic techniques are also being evaluated for their potential application in the changed scenario of providing (99m)Tc from alternate routes. Based on the analysis provided in this review, it appears that some proven separation technologies can be quickly resurrected for the separation of clinical grade (99m)Tc from macroscopic levels of reactor or cyclotron irradiated molybdenum targets. Furthermore, emerging technologies can be developed further to respond to the expected changing modes of (99m)Tc production. Copyright © 2013 Elsevier Inc. All rights reserved.

  14. Robotic inspection technology-process an toolbox

    Energy Technology Data Exchange (ETDEWEB)

    Hermes, Markus [ROSEN Group (United States). R and D Dept.

    2005-07-01

    Pipeline deterioration grows progressively with ultimate aging of pipeline systems (on-plot and cross country). This includes both, very localized corrosion as well as increasing failure probability due to fatigue cracking. Limiting regular inspecting activities to the 'scrapable' part of the pipelines only, will ultimately result into a pipeline system with questionable integrity. The confidence level in the integrity of these systems will drop below acceptance levels. Inspection of presently un-inspectable sections of the pipeline system becomes a must. This paper provides information on ROSEN's progress on the 'robotic inspection technology' project. The robotic inspection concept developed by ROSEN is based on a modular toolbox principle. This is mandatory. A universal 'all purpose' robot would not be reliable and efficient in resolving the postulated inspection task. A preparatory Quality Function Deployment (QFD) analysis is performed prior to the decision about the adequate robotic solution. This enhances the serviceability and efficiency of the provided technology. The word 'robotic' can be understood in its full meaning of Recognition - Strategy - Motion - Control. Cooperation of different individual systems with an established communication, e.g. utilizing Bluetooth technology, support the robustness of the ROSEN robotic inspection approach. Beside the navigation strategy, the inspection strategy is also part of the QFD process. Multiple inspection technologies combined on a single carrier or distributed across interacting container must be selected with a clear vision of the particular goal. (author)

  15. Radioisotopes technology used to probe process problems

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    With the move to a greater degree of sophistication in industrial processes has come a need for improved measurement control methods as well as for efficient techniques for investigating process problems. Radioisotope-based technology, because of its unique benefits, is playing an increasing role in assisting mining and industry to satisfy the critical needs for efficiency in investigating process problems. More than twenty years of experience in the application of radioisotope and radiation techniques to the practical problems of industry has resulted in the Atomic Energy Corporation of South Africa having accumulated both extensive expertise and the facilities to carry out wide-ranging investigations, and to provide a large variety of cost effective services. Some of these are described. 2 figs., 2 ills

  16. Laser Processed Condensing Heat Exchanger Technology Development

    Science.gov (United States)

    Hansen, Scott; Wright, Sarah; Wallace, Sarah; Hamilton, Tanner; Dennis, Alexander; Zuhlke, Craig; Roth, Nick; Sanders, John

    2017-01-01

    The reliance on non-permanent coatings in Condensing Heat Exchanger (CHX) designs is a significant technical issue to be solved before long-duration spaceflight can occur. Therefore, high reliability CHXs have been identified by the Evolvable Mars Campaign (EMC) as critical technologies needed to move beyond low earth orbit. The Laser Processed Condensing Heat Exchanger project aims to solve these problems through the use of femtosecond laser processed surfaces, which have unique wetting properties and potentially exhibit anti-microbial growth properties. These surfaces were investigated to identify if they would be suitable candidates for a replacement CHX surface. Among the areas researched in this project include microbial growth testing, siloxane flow testing in which laser processed surfaces were exposed to siloxanes in an air stream, and manufacturability.

  17. ANALYSIS ON TECHNOLOGICAL PROCESSES CLEANING OIL PIPELINES

    Directory of Open Access Journals (Sweden)

    Mariana PǍTRAŞCU

    2015-05-01

    Full Text Available In this paper the researches are presented concerning the technological processes of oil pipelines.We know several technologies and materials used for cleaning the sludge deposits, iron and manganese oxides, dross, stone, etc.de on the inner walls of drinking water pipes or industries.For the oil industry, methods of removal of waste materials and waste pipes and liquid and gas transport networks are operations known long, tedious and expensive. The main methods and associated problems can be summarized as follows: 1 Blowing with compressed air.2 manual or mechanical brushing, sanding with water or dry.3 Wash with water jet of high pressure, solvent or chemical solution to remove the stone and hard deposits.4 The combined methods of cleaning machines that use water jets, cutters, chains, rotary heads cutters, etc.

  18. The effect of patterning options on embedded memory cells in logic technologies at iN10 and iN7

    Science.gov (United States)

    Appeltans, Raf; Weckx, Pieter; Raghavan, Praveen; Kim, Ryoung-Han; Kar, Gouri Sankar; Furnémont, Arnaud; Van der Perre, Liesbet; Dehaene, Wim

    2017-03-01

    Static Random Access Memory (SRAM) cells are used together with logic standard cells as the benchmark to develop the process flow for new logic technologies. In order to achieve successful integration of Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM) as area efficient higher level embedded cache, it also needs to be included as a benchmark. The simple cell structure of STT-MRAM brings extra patterning challenges to achieve high density. The two memory types are compared in terms of minimum area and critical design rules in both the iN10 and iN7 node, with an extra focus on patterning options in iN7. Both the use of Self-Aligned Quadruple Patterning (SAQP) mandrel and spacer engineering, as well as multi-level via's are explored. These patterning options result in large area gains for the STT-MRAM cell and moreover determine which cell variant is the smallest.

  19. Recovering a time-homogeneous stock price process from perpetual option prices

    OpenAIRE

    Ekström, Erik; Hobson, David

    2009-01-01

    It is well known how to determine the price of perpetual American options if the underlying stock price is a time-homogeneous diffusion. In the present paper we consider the inverse problem, that is, given prices of perpetual American options for different strikes, we show how to construct a time-homogeneous stock price model which reproduces the given option prices.

  20. Technological yields of sources for radiation processing

    International Nuclear Information System (INIS)

    Zagorski, Z.P.

    1993-01-01

    The present report is prepared for planners of radiation processing of any material. Calculations are focused on accelerators of electrons, divided into two groups: versatile linacs of energy up to 13 MeV, and accelerators of lower energy, below 2 MeV, of better energy yield but of limited applications. The calculations are connected with the confrontation of the author's technological expectations during the preparation of the linac project in the late '60s, with the results of 25 years of exploitation of the machine. One has to realize that from the 200 kW input power from the mains, only 5 kW of bent and scanned beam is recovered on the conveyor. That power is only partially used for radiation induced phenomena, because of the demanded homogeneity of the dose, of the mode of packing of the object and its shape, of edges of the scanned area and in the spaces between boxes, and of loses during the idle time due to the tuning of the machine and dosimetric operations. The use of lower energy accelerators may be more economical than that of linacs in case of objects of specific type. At the first stage already, that is of the conversion of electrical power into that of low energy electron beam, the yield is 2-3 times better than in the case of linacs. Attention has been paid to the technological aspects of electron beam conversion into the more penetrating Bremsstrahlung similar to gamma radiation. The advantages of technologies, which make possible a control of the shape of the processed object are stressed. Special attention is focused to the relation between the yield of processing and the ratio between the maximum to the minimum dose in the object under the irradiation. (author). 14 refs, 14 figs

  1. Comparing composts formed by different technological processing

    Science.gov (United States)

    Lyckova, B.; Mudrunka, J.; Kucerova, R.; Glogarova, V.

    2017-10-01

    The presented article compares quality of composts which were formed by different technological processes. The subject to comparison was a compost which was created in a closed fermenter where ideal conditions for decomposition and organic substances conversion were ensured, with compost which was produced in an open box of community composting. The created composts were analysed to determine whether it is more important for the final compost to comply with the composting conditions or better sorting of raw materials needed for compost production. The results of the carried out experiments showed that quality of the resulting compost cannot be determined unequivocally.

  2. Should France invest in new nuclear technology? The enhancement of the EPR project using 'real option' method

    International Nuclear Information System (INIS)

    Epaulard, A.; Gallon, St.

    2000-01-01

    The mathematical tools developed to enhance financial options can also be used to calculate the economics value of investment projects which offer flexibility but whose return is uncertain (like options offered on the stock exchange). In this article, an enhancement method of this kind is applied to a construction project (in 2000) for an EPR nuclear prototype. This prototype will make it possible to use EPR to renew the French electrical infrastructure in 2020 (flexibility), but its economic value will depend upon competitiveness vis-a-vis other production methods available at this time (hence an uncertain return). We demonstrate that investing in EPR technology in 2000 will provide sufficient flexibility in 2020 to be considered profitable, even though it is improbable that the EPR technology will be used at the end of this period. The investment agreed in 2000 to expand EPR technology therefore effectively has the role of an option, or of an insurance policy (guaranteeing against the risk that traditional electricity production methods will be expensive in 2020). (authors)

  3. Wind energy technology: an option for a renewable clean environment energy. Low impact renewable energy: options for a clean environment and healthy Canadian economy

    International Nuclear Information System (INIS)

    Salmon, J.

    1999-01-01

    As Canada debates ways to address climate change, the country's low-impact renewable energy industries want to ensure that Canadians are provided with all of the options available to them. Accordingly, they have come together to create Options for a Clean Environment and Healthy Canadian Economy. Recognizing there is no 'silver bullet' solution to climate change, this document identifies an important suite of measures that, along with others, will allow Canada to achieve its long-term economic and environmental goals. The measures described in this document represent an investment in Canada's future. If implemented, they will reduce annual greenhouse gas (GHG) emissions by more than 12 million tonnes (Mt) by the year 2010 (roughly 8% of Canada's reduction target), create thousands of new jobs, and reduce health-care costs by millions of dollars each year. The most significant dividends from these measures, however, will occur after 2010 as a result of having set in motion fundamental changes in the attitudes of Canadians and the nature of the Canadian energy market. By 2020, the spin-off actions prompted by these measures will likely have resulted in GHG reductions twice as great as those achieved in 2010. This document highlights the opportunities associated specifically with Canada's low-impact renewable energy resources. These are non-fossil-fuel resources that are replenished through the earth's natural cycles and have a minimal impact on the environment and human health. They include wind, solar, earth energy, run-of-river hydro and sustainable biomass fuels. These resources can replace fossil fuels in a variety of areas, including electricity and space and water heating. Fuel cells, although not a renewable resource in themselves, are a promising technology that in combination with renewables have the potential to deliver versatile low-impact electricity. The document also identifies opportunities associated with the increased use of passive renewable energy

  4. Assessment of cleaner process options : a case study from petroleum refining

    Energy Technology Data Exchange (ETDEWEB)

    Weston, N. [Surrey Univ., Guildford (United Kingdom). Centre for Environmental Strategy; Chevron Ltd., Pembroke Point (United Kingdom); Clift, R.; Basson, L. [Surrey Univ., Guildford (United Kingdom). Centre for Environmental Strategy; Pouton, A.; White, N. [Chevron Ltd., Pembroke Point (United Kingdom)

    2008-06-15

    A case study was used to illustrate the challenge of evaluating clean technologies and making modifications to an alkylation unit at a refinery in the United Kingdom. The alkylation unit used hydrogen flouride as an alkylation catalyst and generated fluoridic wastes that required further treatment. The alkylation process is used to produce a high value petroleum blend used for transport fuels. Acidic catalysts are used to eliminate the need for high temperatures and pressures. The study identified possible alterations to enable partial recycling. Different system boundaries were identified. The study considered technological, social, environmental and economic changes associated with the implementation of the process. A life cycle inventory of various processes considered for the refinery was presented. Possible technological changes that could avoid, reduce, or enable partial recycling waste were presented. Losses to relief systems, defluorinators, potassium hydroxide (KOH) treaters, and neutralization systems were also considered. Results of the study showed that the decision-making process involved trade-offs between costs and benefits with considerable uncertainties. It was concluded that the financial scale of projects cannot be used as a guide to systematic sustainability assessment. 50 refs., 3 tabs., 6 figs.

  5. Statistical processing of technological and radiochemical data

    International Nuclear Information System (INIS)

    Lahodova, Zdena; Vonkova, Kateřina

    2011-01-01

    The project described in this article had two goals. The main goal was to compare technological and radiochemical data from two units of nuclear power plant. The other goal was to check the collection, organization and interpretation of routinely measured data. Monitoring of analytical and radiochemical data is a very valuable source of knowledge for some processes in the primary circuit. Exploratory analysis of one-dimensional data was performed to estimate location and variability and to find extreme values, data trends, distribution, autocorrelation etc. This process allowed for the cleaning and completion of raw data. Then multiple analyses such as multiple comparisons, multiple correlation, variance analysis, and so on were performed. Measured data was organized into a data matrix. The results and graphs such as Box plots, Mahalanobis distance, Biplot, Correlation, and Trend graphs are presented in this article as statistical analysis tools. Tables of data were replaced with graphs because graphs condense large amounts of information into easy-to-understand formats. The significant conclusion of this work is that the collection and comprehension of data is a very substantial part of statistical processing. With well-prepared and well-understood data, its accurate evaluation is possible. Cooperation between the technicians who collect data and the statistician who processes it is also very important. (author)

  6. Role of centralized review processes for making reimbursement decisions on new health technologies in Europe.

    Science.gov (United States)

    Stafinski, Tania; Menon, Devidas; Davis, Caroline; McCabe, Christopher

    2011-01-01

    The purpose of this study was to compare centralized reimbursement/coverage decision-making processes for health technologies in 23 European countries, according to: mandate, authority, structure, and policy options; mechanisms for identifying, selecting, and evaluating technologies; clinical and economic evidence expectations; committee composition, procedures, and factors considered; available conditional reimbursement options for promising new technologies; and the manufacturers' roles in the process. A comprehensive review of publicly available information from peer-reviewed literature (using a variety of bibliographic databases) and gray literature (eg, working papers, committee reports, presentations, and government documents) was conducted. Policy experts in each of the 23 countries were also contacted. All information collected was reviewed by two independent researchers. Most European countries have established centralized reimbursement systems for making decisions on health technologies. However, the scope of technologies considered, as well as processes for identifying, selecting, and reviewing them varies. All systems include an assessment of clinical evidence, compiled in accordance with their own guidelines or internationally recognized published ones. In addition, most systems require an economic evaluation. The quality of such information is typically assessed by content and methodological experts. Committees responsible for formulating recommendations or decisions are multidisciplinary. While criteria used by committees appear transparent, how they are operationalized during deliberations remains unclear. Increasingly, reimbursement systems are expressing interest in and/or implementing reimbursement policy options that extend beyond the traditional "yes," "no," or "yes with restrictions" options. Such options typically require greater involvement of manufacturers which, to date, has been limited. Centralized reimbursement systems have become an

  7. Report of the Defense Science Board Task Force on Tritium Production Technology Options

    Science.gov (United States)

    1999-01-01

    pressurized water reactors are replaced with lithium aluminate ceramic rods, called Tritium- Producing Burnable Absorber Rods (TPBARs). The rods are...the options to provide a credible present value calculation . In any case, the constant dollar portrayal provides useful information. The cost to

  8. Development of Industrial Process Diagnosis and Measurement Technology

    International Nuclear Information System (INIS)

    Jung, Sung Hee; Kim, Jong Bum; Moon, Jin Ho

    2010-04-01

    Section 1. Industrial Gamma CT Technology for Process Diagnosis: The project is aimed to develop industrial process gamma tomography system for investigation on structural and physical malfunctioning and process media distribution by means of sealed gamma source and radioactive materials. Section 2. Development of RI Hydraulic Detection Technology for Industrial Application: The objectives in this study are to develop the evaluation technology of the hydrological characteristics and the hydraulic detection technology using radioisotope, and to analyze the hydrodynamics and pollutant transport in water environment like surface and subsurface. Section 3. Development of RT-PAT System for Powder Process Diagnosis: The objective of this project is the development of a new radiation technology to improve the accuracy of the determination of moisture content in a powder sample by using radiation source through the so-called RT-PAT (Radiation Technology-Process Analytical Technology), which is a new concept of converging technology between the radiation technology and the process analytical technology

  9. Development of industrial process diagnosis and measurement technology

    International Nuclear Information System (INIS)

    Jung, Sunghee; Kim, Jongbum; Moon, Jinho; Suh, Kyungsuk; Kim, Jongyun

    2012-04-01

    Section1. Industrial Gamma CT Technology for Process Diagnosis The project is aimed to develop industrial process gamma tomography system for investigation on structural and physical malfunctioning and process media distribution by means of sealed gamma source and radioactive materials. Section2. Development of RI Hydraulic Detection Technology for Industrial Application The objectives in this study are to develop the evaluation technology of the hydrological characteristics and the hydraulic detection technology using radioisotope, and to analyze the hydrodynamics and pollutant transport in water environment like surface and subsurface. Section3. Development of RT-PAT System for Powder Process Diagnosis The objective of this project is the development of a new radiation technology to improve the accuracy of the determination of moisture content in a powder sample by using radiation source through the so-called RT-PAT (Radiation Technology-Process Analytical Technology), which is a new concept of converging technology between the radiation technology and the process analytical technology

  10. Software engineering technology transfer: Understanding the process

    Science.gov (United States)

    Zelkowitz, Marvin V.

    1993-01-01

    Technology transfer is of crucial concern to both government and industry today. In this report, the mechanisms developed by NASA to transfer technology are explored and the actual mechanisms used to transfer software development technologies are investigated. Time, cost, and effectiveness of software engineering technology transfer is reported.

  11. Plasma spray technology process parameters and applications

    International Nuclear Information System (INIS)

    Sreekumar, K.P.; Karthikeyan, J.; Ananthapadmanabhan, P.V.; Venkatramani, N.; Chatterjee, U.K.

    1991-01-01

    The current trend in the structural design philosophy is based on the use of substrate with the necessary mechanical properties and a thin coating to exhibit surface properties. Plasma spray process is a versatile surface coating technique which finds extensive application in meeting advance technologies. This report describes the plasma spray technique and its use in developing coatings for various applications. The spray system is desribed in detail including the different variables such as power input to the torch, gas flow rate, powder properties, powder injection, etc. and their interrelation in deciding the quality of the coating. A brief write-up on the various plasma spray coatings developed for different applications is also included. (author). 15 refs., 15 figs., 2 tabs

  12. A short review on SSF – an interesting process option for ethanol production from lignocellulosic feedstocks

    Directory of Open Access Journals (Sweden)

    Bertilsson Magnus

    2008-05-01

    Full Text Available Abstract Simultaneous saccharification and fermentation (SSF is one process option for production of ethanol from lignocellulose. The principal benefits of performing the enzymatic hydrolysis together with the fermentation, instead of in a separate step after the hydrolysis, are the reduced end-product inhibition of the enzymatic hydrolysis, and the reduced investment costs. The principal drawbacks, on the other hand, are the need to find favorable conditions (e.g. temperature and pH for both the enzymatic hydrolysis and the fermentation and the difficulty to recycle the fermenting organism and the enzymes. To satisfy the first requirement, the temperature is normally kept below 37°C, whereas the difficulty to recycle the yeast makes it beneficial to operate with a low yeast concentration and at a high solid loading. In this review, we make a brief overview of recent experimental work and development of SSF using lignocellulosic feedstocks. Significant progress has been made with respect to increasing the substrate loading, decreasing the yeast concentration and co-fermentation of both hexoses and pentoses during SSF. Presently, an SSF process for e.g. wheat straw hydrolyzate can be expected to give final ethanol concentrations close to 40 g L-1 with a yield based on total hexoses and pentoses higher than 70%.

  13. Transform-based evaluation of prices and Greeks of lookback options driven by Lévy processes

    NARCIS (Netherlands)

    Asghari, N.M.; Mandjes, M.

    2016-01-01

    In this paper, we develop a technique, based on numerical inversion, to compute the prices and Greeks of lookback options driven by Lévy processes. In this setup, the risk neutral evolution of the stock price, say St , is given by S0eΧt , with S0 the initial price and Χt a Lévy process. Lookback

  14. Evaluating strategic investments : real options' role in new manufacturing technology projects

    OpenAIRE

    Silva, Patrícia Pereira da

    1998-01-01

    The decision to invest, particularly in new manufacturing tecnologies, is often hampered by using conventional methods of capital investment analysis. Limitations of current approaches are discussed and new frameworks that are being presented in the literature with regard to strategic concern are analysed. It is discussed how real options, a relatively recent technique from this the finance area, may provide the ability to measure some of the benefits that are presently treated.

  15. Application of Java technology in radiation image processing

    International Nuclear Information System (INIS)

    Cheng Weifeng; Li Zheng; Chen Zhiqiang; Zhang Li; Gao Wenhuan

    2002-01-01

    The acquisition and processing of radiation image plays an important role in modern application of civil nuclear technology. The author analyzes the rationale of Java image processing technology which includes Java AWT, Java 2D and JAI. In order to demonstrate applicability of Java technology in field of image processing, examples of application of JAI technology in processing of radiation images of large container have been given

  16. COMPLEX PROCESSING TECHNOLOGY OF TOMATO RAW MATERIALS

    Directory of Open Access Journals (Sweden)

    A. M. Gadzhieva

    2015-01-01

    Full Text Available Tomatoes grown in the central and southern parts of the country, which contain 5-6 % of solids, including 0.13 % of pectin, 0.86 % of fat, 0.5 % of organic acids; 0.5 % minerals, etc. were used as a subject of research. These tomatoes, grown in the mountains, on soils with high salinity, contain high amounts of valuable components and have a long-term preservation. For the extraction of valuable components from dried tomato pomace CO2 extraction method was applied. Technological and environmental feasibility of tomatoes stage drying in the atmosphere of inert gas in solar dry kiln were evaluated; production scheme of dried tomatoes is improved; a system for tomato pomace drying is developed; a production scheme of powders of pulp, skin and seeds of tomatoes is developed. Combined method of tomato pomace drying involves the simultaneous use of the electromagnetic field of low and ultra-high frequency and blowing product surface with hot nitrogen. Conducting the drying process in an inert gas atmosphere of nitrogen intensified the process of moisture removing from tomatoes. The expediency of using tomato powder as enriching additive was proved. Based on the study of the chemical composition of the tomato powder made from Dagestan varieties of tomatoes, and on the organoleptic evaluation and physico-chemical studies of finished products, we have proved the best degree of recoverability of tomato powder during the production of reconstituted juice and tomato beverages.

  17. Process technology - rare and refractory metals

    International Nuclear Information System (INIS)

    Gupta, C.K.; Bose, D.K.

    1989-01-01

    India has fairly rich resreves of rare and refractory metals. Abundant sources of ilmenite, rutile, zircon and rare earths are found in the placer deposits of the southern and eastern coasts of the country. Columbite-tantalite occur in mica and the mining belts of Bihar and cassiterite deposits are found in Bastar (Madhya Pradesh). Vanadium as a minor associate occurs in bauxites and in the vast deposits of titaniferrous magnetites. Over the years, research and development and pilot plant works in many research organisations in India have built up a sound technological base in the country for process metallurgy of many refractory and rare earth metals starting from their indigenous sources. The present paper provides a comprehensive view of the developments that have taken place till now on the processing of various refractory and rare earth metals with particular reference to the extensive work carried out at the Department of Atomic Energy. The coverage includes mineral benification separation of individual elements, preparation of pure intermediates, techniques of reduction to metal and final purification. The paper also reviews some of the recent developments that have been taken place in these fields and the potential application of these metals in the foreseeable future. (author). 22 refs., 18 fi g., 7 tabs

  18. Development and application of a probabilistic evaluation method for advanced process technologies

    Energy Technology Data Exchange (ETDEWEB)

    Frey, H.C.; Rubin, E.S.

    1991-04-01

    The objective of this work is to develop and apply a method for research planning for advanced process technologies. To satisfy requirements for research planning, it is necessary to: (1) identify robust solutions to process design questions in the face of uncertainty to eliminate inferior design options; (2) identify key problem areas in a technology that should be the focus of further research to reduce the risk of technology failure; (3) compare competing technologies on a consistent basis to determine the risks associated with adopting a new technology; and (4) evaluate the effects that additional research might have on comparisons with conventional technology. An important class of process technologies are electric power plants. In particular, advanced clean coal technologies are expected to play a key role in the energy and environmental future of the US, as well as in other countries. Research planning for advanced clean coal technology development is an important part of energy and environmental policy. Thus, the research planning method developed here is applied to case studies focusing on a specific clean coal technology. The purpose of the case studies is both to demonstrate the research planning method and to obtain technology-specific conclusions regarding research strategies.

  19. Development and application of a probabilistic evaluation method for advanced process technologies. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Frey, H.C.; Rubin, E.S.

    1991-04-01

    The objective of this work is to develop and apply a method for research planning for advanced process technologies. To satisfy requirements for research planning, it is necessary to: (1) identify robust solutions to process design questions in the face of uncertainty to eliminate inferior design options; (2) identify key problem areas in a technology that should be the focus of further research to reduce the risk of technology failure; (3) compare competing technologies on a consistent basis to determine the risks associated with adopting a new technology; and (4) evaluate the effects that additional research might have on comparisons with conventional technology. An important class of process technologies are electric power plants. In particular, advanced clean coal technologies are expected to play a key role in the energy and environmental future of the US, as well as in other countries. Research planning for advanced clean coal technology development is an important part of energy and environmental policy. Thus, the research planning method developed here is applied to case studies focusing on a specific clean coal technology. The purpose of the case studies is both to demonstrate the research planning method and to obtain technology-specific conclusions regarding research strategies.

  20. Petroleum coke adsorption as a water management option for oil sands process-affected water

    International Nuclear Information System (INIS)

    Zubot, Warren; MacKinnon, Michael D.; Chelme-Ayala, Pamela; Smith, Daniel W.; Gamal El-Din, Mohamed

    2012-01-01

    Water is integral to both operational and environmental aspects of the oil sands industry. A water treatment option based on the use of petroleum coke (PC), a by-product of bitumen upgrading, was examined as an opportunity to reduce site oil sands process-affected water (OSPW) inventories and net raw water demand. Changes in OSPW quality when treated with PC included increments in pH levels and concentrations of vanadium, molybdenum, and sulphate. Constituents that decreased in concentration after PC adsorption included total acid-extractable organics (TAO), bicarbonate, calcium, barium, magnesium, and strontium. Changes in naphthenic acids (NAs) speciation were observed after PC adsorption. A battery of bioassays was used to measure the OSPW toxicity. The results indicated that untreated OSPW was toxic towards Vibrio fischeri and rainbow trout. However, OSPW treated with PC at appropriate dosages was not acutely toxic towards these test organisms. Removal of TAO was found to be an adsorption process, fitting the Langmuir and Langmuir–Freundlich isotherm models. For TAO concentrations of 60 mg/L, adsorption capacities ranged between 0.1 and 0.46 mg/g. This study demonstrates that freshly produced PC from fluid cokers provides an effective treatment of OSPW in terms of key constituents' removal and toxicity reduction. - Highlights: ► Treatment of oil sands process-affected water (OSPW) using petroleum coke (PC) adsorption was investigated. ► PC was effective at adsorbing naphthenic acids with higher cyclicity. ► OSPW treated with PC at appropriate dosages was not toxic towards Vibrio fisheri and rainbow trout. ► The adsorption of organic acids fitted the Langmuir and Langmuir–Freundlich isotherm models. ► PC has the potential to be an effective adsorbent to treat OSPW either directly or as a pretreatment step.

  1. Petroleum coke adsorption as a water management option for oil sands process-affected water

    Energy Technology Data Exchange (ETDEWEB)

    Zubot, Warren [Syncrude Canada Ltd., Research and Development, Edmonton, Alberta, Canada T6N 1H4 (Canada); MacKinnon, Michael D. [OSPM Solutions Ltd., Hamilton, Ontario, Canada L8H 6X2 (Canada); Chelme-Ayala, Pamela; Smith, Daniel W. [University of Alberta, Department of Civil and Environmental Engineering, Edmonton, Alberta, Canada T6G 2W2 (Canada); Gamal El-Din, Mohamed, E-mail: mgamalel-din@ualberta.ca [University of Alberta, Department of Civil and Environmental Engineering, Edmonton, Alberta, Canada T6G 2W2 (Canada)

    2012-06-15

    Water is integral to both operational and environmental aspects of the oil sands industry. A water treatment option based on the use of petroleum coke (PC), a by-product of bitumen upgrading, was examined as an opportunity to reduce site oil sands process-affected water (OSPW) inventories and net raw water demand. Changes in OSPW quality when treated with PC included increments in pH levels and concentrations of vanadium, molybdenum, and sulphate. Constituents that decreased in concentration after PC adsorption included total acid-extractable organics (TAO), bicarbonate, calcium, barium, magnesium, and strontium. Changes in naphthenic acids (NAs) speciation were observed after PC adsorption. A battery of bioassays was used to measure the OSPW toxicity. The results indicated that untreated OSPW was toxic towards Vibrio fischeri and rainbow trout. However, OSPW treated with PC at appropriate dosages was not acutely toxic towards these test organisms. Removal of TAO was found to be an adsorption process, fitting the Langmuir and Langmuir-Freundlich isotherm models. For TAO concentrations of 60 mg/L, adsorption capacities ranged between 0.1 and 0.46 mg/g. This study demonstrates that freshly produced PC from fluid cokers provides an effective treatment of OSPW in terms of key constituents' removal and toxicity reduction. - Highlights: Black-Right-Pointing-Pointer Treatment of oil sands process-affected water (OSPW) using petroleum coke (PC) adsorption was investigated. Black-Right-Pointing-Pointer PC was effective at adsorbing naphthenic acids with higher cyclicity. Black-Right-Pointing-Pointer OSPW treated with PC at appropriate dosages was not toxic towards Vibrio fisheri and rainbow trout. Black-Right-Pointing-Pointer The adsorption of organic acids fitted the Langmuir and Langmuir-Freundlich isotherm models. Black-Right-Pointing-Pointer PC has the potential to be an effective adsorbent to treat OSPW either directly or as a pretreatment step.

  2. Ion Implantation Processing Technologies for Telecommunications Electronics

    Energy Technology Data Exchange (ETDEWEB)

    Haynes, T E

    2000-05-01

    The subject CRADA was a collaboration between Oak Ridge National Laboratory and Bell Laboratories, Lucent Technologies (formerly AT and T Bell Laboratories) to explore the development of ion implantation technologies for silicon integrated circuit (IC) manufacturing.

  3. Identification of technology options for reducing nitrogen pollution in cropping systems of Pujiang

    NARCIS (Netherlands)

    Fang, B.; Wang, G.; Berg, van den M.M.; Roetter, R.P.

    2005-01-01

    This work analyses the potential role of nitrogen pollution technology of crop systems of Pujiang, County in Eastern China¿s Zhejiang Province, rice and vegetables are important cropping systems. We used a case study approach involving comparison of farmer practices and improved technologies. This

  4. Information Technology Training within Traineeships: Options for TAFE-Based Courses.

    Science.gov (United States)

    Hall, W.; And Others

    A study explored ways in which traineeship courses could be designed to include training in information technology. The skills and performance standards required of information technology training in the printing, tourism, banking, construction, and computer industries were identified. Next, the current provision of such training in Australia and…

  5. Process Technology for Immobilized LipaseProcess Technology for Immobilized Lipase-catalyzed

    DEFF Research Database (Denmark)

    Xu, Yuan

    (e.g. a hydrophobic carrier for the immobilized lipase and the capabilities to provide sufficient mixing as well as stepwise/continuous feeding of ethanol to the reactor). An STR is efficient for batch operation while a PBR is efficient for a continuous production. An STR can more easily provide...... sufficient external mass transfer for a reaction, but will lead to more mechanical damage of the biocatalyst particles, than a PBR. A reactor combination of CSTR with PBR can couple the advantages of both, delivering an efficient continuous process.The second case study (esterification) shares some similar......-catalyzed transesterification is that it is multi-phasic system. The by-product glycerol can potentially impose inhibitory effects on immobilized lipases and likewise the un-dissolved ethanol can inhibit the lipase. The options for addressing these issues can be used as the basis for selecting the biocatalyst and the reactor...

  6. A Design Process for Creative Technology

    NARCIS (Netherlands)

    Mader, Angelika H.; Eggink, Wouter; Bohemia, E.; Eger, A.; Eggink, W.; Kovacevic, A.; Parkinson, B; Wits, W.

    Creative Technology is a new bachelor programme at the University of Twente. Goal of Creative Technology is to design products and applications that improve the quality of daily life in its manifold aspects, building on Information and Communication Technology (ICT). The application domains range

  7. Assessment of Greenhouse Gas Control Technology Options within the Energy, Water and Food Nexus

    Science.gov (United States)

    Al-Ansari, Tareq; Korre, Anna; Nie, Zhenggang; Shah, Nilay

    2015-04-01

    The utilisation of Energy, Water and Food (EWF) resources can be described as a nexus of complex linkages embodied in industrial and natural processes. Food production is one such example of a system that mobilises EWF resources to deliver a product which is highly influenced by the efficiency of the industrial processes contributing to it and the conditions of the surrounding natural environment. Aggregating the utilisation of EWF resources into interconnected sub-systems is necessary for the accurate representation of the system's dynamics in terms of its material flow and resource consumption. The methodology used in this study is an extension of previous work developed regarding nexus analysis (Al-Ansari et al. 2014a, Al-Ansari et al. 2014b). Life cycle assessment (LCA) is used to prepare detailed models of the sub-system components, determine the linkages between the different nexus constituents and evaluate impacts on the natural environment. The nexus system is comprised of water sub-systems represented by a reverse osmosis (RO) desalination process. Energy sub-systems for power generation include models for a combined cycle gas turbine (CCGT) and solar Photovoltaics (PV) energy generation, as well as an amine based CO2 capture process enabling the utilisation of CO2 for the artificial fertilization of crops. The agricultural sub-systems include the production and application of fertilizers and the raising of livestock. A biomass integrated gasification combined cycle (BIGCC) for power generation using waste manure from the livestock sub-system is also included. The objective of this study is to consider a conventional food system in Qatar and enhance its environmental performance by using a nexus approach to examine different scenarios and operating modes. For the Qatar case study, three scenarios and four modes of operation were developed as part of the analysis. The baseline scenario uses fossil fuel to power the entire EWF nexus system using CCGT, the

  8. Error analysis in Fourier methods for option pricing for exponential Lévy processes

    KAUST Repository

    Crocce, Fabian

    2015-01-07

    We derive an error bound for utilising the discrete Fourier transform method for solving Partial Integro-Differential Equations (PIDE) that describe european option prices for exponential Lévy driven asset prices. We give sufficient conditions for the existence of a L? bound that separates the dynamical contribution from that arising from the type of the option n in question. The bound achieved does not rely on information of the asymptotic behaviour of option prices at extreme asset values. In addition, we demonstrate improved numerical performance for select examples of practical relevance when compared to established bounding methods.

  9. Uncertainty modeling process for semantic technology

    Directory of Open Access Journals (Sweden)

    Rommel N. Carvalho

    2016-08-01

    Full Text Available The ubiquity of uncertainty across application domains generates a need for principled support for uncertainty management in semantically aware systems. A probabilistic ontology provides constructs for representing uncertainty in domain ontologies. While the literature has been growing on formalisms for representing uncertainty in ontologies, there remains little guidance in the knowledge engineering literature for how to design probabilistic ontologies. To address the gap, this paper presents the Uncertainty Modeling Process for Semantic Technology (UMP-ST, a new methodology for modeling probabilistic ontologies. To explain how the methodology works and to verify that it can be applied to different scenarios, this paper describes step-by-step the construction of a proof-of-concept probabilistic ontology. The resulting domain model can be used to support identification of fraud in public procurements in Brazil. While the case study illustrates the development of a probabilistic ontology in the PR-OWL probabilistic ontology language, the methodology is applicable to any ontology formalism that properly integrates uncertainty with domain semantics.

  10. Science, Technology, Engineering, and Mathematics (STEM) Education Issues and Legislative Options

    National Research Council Canada - National Science Library

    Kuenzi, Jeffrey J; Matthews, Christine M; Mangan, Bonnie F

    2006-01-01

    There is growing concern that the United States is not preparing a sufficient number of students, teachers, and practitioners in the areas of science, technology, engineering, and mathematics (STEM...

  11. Risoe energy report 1. New and emerging technologies - options for the future

    International Nuclear Information System (INIS)

    Larsen, H.; Soenderberg Petersen, L.

    2002-10-01

    All over the world, increasing energy consumption, liberalisation of energy markets and the need to take action on climate change are producing new challenges for the energy sector. At the same time there is increasing pressure for research, new technology and industrial products to be socially acceptable and to generate prosperity. The result is a complex and dynamic set of conditions affecting decisions on investment in research and new energy technology. To meet these challenges in the decades ahead, industrialists and policymakers need appropriate analyse energy systems, plus knowledge of trends for existing technologies and prospects for emerging technologies. This is the background for this first Risoe Energy Report, which sets out the global, European and Danish energy scene together with trends in development and emerging technologies. The report is the first in a new series from Risoe National Laboratory. The global energy developments are presented based on the latest available information from authoritative sources like IEA, WEC, World Energy Assessment etc. Some of the major challenges are presented in terms of the changing energy markets in all regions, the focus on environmental concerns in the industrialised countries, and energy for development and access to energy for the poor in developing countries. The report presents the status of R and D in progress for supply technologies. The various technologies are assessed with respect to status, trends and perspectives for the technology, and international R and D plans. For the technologies where Risoe is undertaking R and D this is highlighted in a separate section. Recent studies of emerging energy technologies from international organisations and leading research organisations are reviewed. There are reviews of national research activities on new energy technologies in a number of countries as well as in Risoe National Laboratory. Conclusions for Danish energy supply, Danish industry, and Danish

  12. Engaging China in the International Export Control Process: Options for U.S. Policy

    National Research Council Canada - National Science Library

    Goldman, Charles

    1995-01-01

    .... objectives and potential policy initiatives toward that end. Using knowledge about the operation of the Chinese bureaucratic system, especially in defense related research and development, the briefing describes a number of strategy options for U.S...

  13. Policy options to promote energy efficient and environmentally sound technologies in small- and medium-scale industries

    International Nuclear Information System (INIS)

    Thiruchelvam, M.; Kumar, S.; Visvanathan, C.

    2003-01-01

    The rapid industrialization of Asian developing countries has pushed the need for more energy at the cost of environmental degradation. Though large industries are targeted for energy conservation and pollution prevention, small and medium scale industries (SMI) also contribute to significant pollution. This paper discusses the role of SMI in the economy, its energy consumption and impact on the environment. An overview of the energy and environment policies of China, India, Sri Lanka, the Philippines and Vietnam, and the role of energy efficient and environmentally sound technologies (E 3 ST) as a viable means to meet these modern challenges in SMI is discussed. The barriers faced in adopting these technologies have been identified and an analysis has been done of the various strategies and policy options available to governments to promote E 3 ST in SMI. Examples and illustrations of such successful efforts have also been highlighted

  14. Flexible process options for the immobilisation of residues and wastes containing plutonium

    International Nuclear Information System (INIS)

    Stewart, M.W.A.; Moricca, S.A.; Day, R. A.; Begg, B. D.; Scales, C. R.; Maddrell, E. R.; Eilbeck, A. B.

    2007-01-01

    Residues and waste streams containing plutonium present unique technical, safety, regulatory, security, and socio-political challenges. In the UK these streams range from lightly plutonium contaminated materials (PCM) through to residue s resulting directly from Pu processing operations. In addition there are potentially stocks of Pu oxide powders whose future designation may be either a waste or an asset, due to their levels of contamination making their reuse uneconomic, or to changes in nuclear policy. While waste management routes exist for PCM, an immobilisation process is required for streams containing higher levels of Pu. Such a process is being developed by Nexia Solutions and ANSTO to treat and immobilise Pu waste and residues currently stored on the Sellafield site. The characteristics of these Pu waste streams are highly variable. The physical form of the Pu waste ranges from liquids, sludges, powders/granules, to solid components (e.g., test fuels), with the Pu present as an ion in solution, as a salt, metal, oxide or other compound. The chemistry of the Pu waste streams also varies considerably with a variety of impurities present in many waste streams. Furthermore, with fissile isotopes present, criticality is an issue during operations and in the store or repository. Safeguards and security concerns must be assessed and controlled. The process under development, by using a combination of tailored waste form chemistry combined with flexible process technology aims to develop a process line to handle a broad range of Pu waste streams. It aims to be capable of dealing with not only current arisings but those anticipated to arise as a result of future operations or policy changes. (authors)

  15. Adoption of improved oil palm processing technology in Umuahia ...

    African Journals Online (AJOL)

    It was found that a large percentage of the respondents were aware of the 5 improved oil palm processing technologies with friends and relatives as major source of information. Adoption was significant for 3 out of 5 technologies under study. The major constraints to improved oil palm processing technologies were high ...

  16. The Process of Accepting Technology Innovation for Rural Teachers

    Science.gov (United States)

    Cerovski, Jeremy

    2016-01-01

    In order for educational leaders to facilitate effectively the integration of technology, an understanding of the process rural teachers experience with technology integration is critical. The goal of the qualitative study was to discover and understand rural teachers' process for accepting technology innovation in order to improve the…

  17. TECHNOLOGY SUMMARY ADVANCING TANK WASTE RETRIEVAL AND PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    SAMS TL; MENDOZA RE

    2010-08-11

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  18. TECHNOLOGY SUMMARY ADVANCING TANK WASTE RETREIVAL AND PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    SAMS TL

    2010-07-07

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  19. Technology transfer on long-term radioactive waste management - a feasible option for small nuclear programmes?

    International Nuclear Information System (INIS)

    Mele, I.; Mathieson, J.

    2007-01-01

    The EU project CATT - Co-operation and technology transfer on long-term radioactive waste management for Member States with small nuclear programmes investigated the feasibility of countries with small nuclear programmes implementing long-term radioactive waste management solutions within their national borders, through collaboration on technology transfer with those countries with advanced disposal concepts. The main project objective was to analyse the existing capabilities of technology owning Member States and the corresponding requirements of potential technology acquiring Member States and, based on the findings, to develop a number of possible collaboration models and scenarios that could be used in a technology transfer scheme. The project CATT was performed as a specific support action under the EU sixth framework programme and it brought together waste management organisations from six EU Member States: UK, Bulgaria, Germany, Lithuania, Slovenia and Sweden. In addition, the EC Joint Research Centre from the Netherlands also participated as a full partner. The paper summarises the analyses performed and the results obtained within the project. (author)

  20. The Clean Coal Technology Program: Options for SO2, NOx, and particulate control

    International Nuclear Information System (INIS)

    Strakey, J.P.; Hargis, R.; Eastman, M.L.; Santore, R.R.

    1992-01-01

    There are currently 42 active projects in the Clean Coal Technology Program. The Pittsburgh Energy Technology Center (PETC) is responsible for managing 30 of these projects: five projects under Clean Coal 1, ten projects under Clean Coal 2, nine projects under Clean Coal 3, and six projects under Clean Coal 4. This paper describes each of the PETC projects, including the technologies involved and the project status. Many of the projects will use advanced approaches to meet current and future requirements for particulate and air toxic emissions. Discussion of these aspects have been expanded in this summary paper to address the focus of this symposium. Additional information can be provided to interested particles either through DOE, the participant or the technology supplier. Numerous non-federal organizations including state and utility/industry research groups provide important co-funding and other support for these CCT projects. Space limitations prohibit listing them in this paper; however, a complete listing can be found in the Clean Coal Technology Demonstration Program Update 1990. Appendix A to this paper contains flow diagrams for all the projects

  1. Integrating Digital Technologies in Teaching Learning Process

    Science.gov (United States)

    Nagarajan, R.; Velmanirajan, K.; Kanna, K. Sankesh

    2013-01-01

    India has made impressive strides in the application of information and communication technology in recent years and this has reflected in a vibrant and fast growing economy. It is now an acknowledged world leader in the knowledge industry. In this paper an attempt is made to highlight the role of Information and Communication Technology (ICT) in…

  2. Knowledge and cognitive process dimensions of Technology ...

    African Journals Online (AJOL)

    Technology was introduced into the South African school curriculum in recognition of the need to produce more engineers, technicians and artisans and thus to be a vehicle to develop readiness for a competitive and technology-driven economy (Department of Basic Education, 2011). Bloch (2007) avers that it is due to the ...

  3. A Technology Approach to Improving Process Management

    Science.gov (United States)

    Dray, Lori; Strasburger, Tom

    2013-01-01

    It is impossible to ignore how technology is infiltrating education. Interactive projectors and other technologies give teachers and students the opportunity to bring lessons to life. Some districts are replacing textbooks with digital content, allowing students to interact with content in new ways. Galion City School District in Galion, Ohio, is…

  4. Plan for advanced microelectronics processing technology application

    Energy Technology Data Exchange (ETDEWEB)

    Goland, A.N.

    1990-10-01

    The ultimate objective of the tasks described in the research agreement was to identify resources primarily, but not exclusively, within New York State that are available for the development of a Center for Advanced Microelectronics Processing (CAMP). Identification of those resources would enable Brookhaven National Laboratory to prepare a program plan for the CAMP. In order to achieve the stated goal, the principal investigators undertook to meet the key personnel in relevant NYS industrial and academic organizations to discuss the potential for economic development that could accompany such a Center and to gauge the extent of participation that could be expected from each interested party. Integrated of these discussions was to be achieved through a workshop convened in the summer of 1990. The culmination of this workshop was to be a report (the final report) outlining a plan for implementing a Center in the state. As events unfolded, it became possible to identify the elements of a major center for x-ray lithography on Lone Island at Brookhaven National Laboratory. The principal investigators were than advised to substitute a working document based upon that concept in place of a report based upon the more general CAMP workshop originally envisioned. Following that suggestion from the New York State Science and Technology Foundation, the principals established a working group consisting of representatives of the Grumman Corporation, Columbia University, the State University of New York at Stony Brook, and Brookhaven National Laboratory. Regular meetings and additional communications between these collaborators have produced a preproposal that constitutes the main body of the final report required by the contract. Other components of this final report include the interim report and a brief description of the activities which followed the establishment of the X-ray Lithography Center working group.

  5. Document Image Processing: Going beyond the Black-and-White Barrier. Progress, Issues and Options with Greyscale and Colour Image Processing.

    Science.gov (United States)

    Hendley, Tom

    1995-01-01

    Discussion of digital document image processing focuses on issues and options associated with greyscale and color image processing. Topics include speed; size of original document; scanning resolution; markets for different categories of scanners, including photographic libraries, publishing, and office applications; hybrid systems; data…

  6. Decision Gate Process for Assessment of a Technology Development Portfolio

    Science.gov (United States)

    Kohli, Rajiv; Fishman, Julianna; Hyatt, Mark

    2012-01-01

    The NASA Dust Management Project (DMP) was established to provide technologies (to TRL 6 development level) required to address adverse effects of lunar dust to humans and to exploration systems and equipment, which will reduce life cycle cost and risk, and will increase the probability of sustainable and successful lunar missions. The technology portfolio of DMP consisted of different categories of technologies whose final product is either a technology solution in itself, or one that contributes toward a dust mitigation strategy for a particular application. A Decision Gate Process (DGP) was developed to assess and validate the achievement and priority of the dust mitigation technologies as the technologies progress through the development cycle. The DGP was part of continuous technology assessment and was a critical element of DMP risk management. At the core of the process were technology-specific criteria developed to measure the success of each DMP technology in attaining the technology readiness levels assigned to each decision gate. The DGP accounts for both categories of technologies and qualifies the technology progression from technology development tasks to application areas. The process provided opportunities to validate performance, as well as to identify non-performance in time to adjust resources and direction. This paper describes the overall philosophy of the DGP and the methodology for implementation for DMP, and describes the method for defining the technology evaluation criteria. The process is illustrated by example of an application to a specific DMP technology.

  7. Value-creating investment strategies to manage risk from structural market uncertainties: Switching and compound options in (V)HTR technologies - HTR2008-58157

    International Nuclear Information System (INIS)

    Lauferts, U.; Halbe, C.; Van Heek, A.

    2008-01-01

    To measure the value of a technology investment under uncertainty with standard techniques like net present value (NPV) or return on investment (ROI) will often uncover the difficulty to present convincing business case. Projected cash flows are inefficient or the discount rate chosen to compensate for the risk is so high, that it is disagreeable to the investor s requirements. Decision making and feasibility studies have to look beyond traditional analysis to reveal the strategic value of a technology investment. Here, a Real Option Analysis (ROA) offers a powerful alternative to standard discounted cash-flow (DCF) methodology by risk-adjusting the cash flow along the decision path rather than risk adjusting the discount rate. Within the GEN IV initiative attention is brought not only towards better sustainability, but also to broader industrial application and improved financing. Especially the HTR design is full of strategic optionalities: The high temperature output facilitates penetration into other non-electricity energy markets like industrial process heat applications and the hydrogen market. The flexibility to switch output in markets with multi-source uncertainties reduces downside risk and creates an additional value of over 50% with regard to the Net Present Value without flexibility. The supplement value of deploying a modular (V)HTR design adds over 100% to the project value using real option evaluation tools. Focus of this paper was to quantify the strategic value that comes along a) with the modular design; a design that offers managerial flexibility adapting a step-by-step investment strategy to the actual market demand and b) with the option to switch between two modes of operation, namely electricity and hydrogen production. We will demonstrate that the effect of uncertain electricity prices can be dampened down with a modular HTR design. By using a real option approach, we view the project as a series of compound options - each option depending

  8. Annual conference on nuclear technology. Nuclear power 2001: option for the future

    International Nuclear Information System (INIS)

    Anon.

    2001-01-01

    The Dresden Palace for Culture was the venue of the ANNUAL MEETING ON NUCLEAR TECHNOLOGY on May 15-17, 2001, the first to be held in Dresden and the first also to be held in one of the new German federal states. Although no nuclear plant is in operation in East Germany after the Greifswald Nuclear Power Station was decommissioned, nuclear technology continues to play an important role especially in research and university teaching in this part of Germany. The organizers of the conference, Deutsches Atomforum e.V. (DAtF) and Kerntechnische Gesellschaft e.V. (KTG), welcomed more than 1000 participants from nineteen countries. The three-day program, with its traditional, proven structure, featured plenary sessions on the first day, and specialized sessions, technical sessions, poster sessions, and other events on the following days. The partner country at the Annual Meeting on Nuclear Technology was Russia, with a session specially devoted to selected topics of the country. The conference was accompanied by a technical exhibition with company meeting points of vendors, suppliers, and service industries. A video film forum was arranged for the interested public which featured contributions about nuclear research, nuclear power plant operation, transport and storage as well as decommissioning. Another major event was a workshop on 'Preserving Competence in Nuclear Technology'. The plenary day is described in this summary report, while the results of the technical sessions as seen by the rapporteurs are printed elsewhere in this issue of atw 8/9, 2001. (orig.) [de

  9. Saccharification of recalcitrant biomass and integration options for lignocellulosic sugars from Catchlight Energy's sugar process (CLE Sugar).

    Science.gov (United States)

    Gao, Johnway; Anderson, Dwight; Levie, Benjamin

    2013-01-28

    Woody biomass is one of the most abundant biomass feedstocks, besides agriculture residuals in the United States. The sustainable harvest residuals and thinnings alone are estimated at about 75 million tons/year. These forest residuals and thinnings could produce the equivalent of 5 billion gallons of lignocellulosic ethanol annually. Softwood biomass is the most recalcitrant biomass in pretreatment before an enzymatic hydrolysis. To utilize the most recalcitrant lignocellulosic materials, an efficient, industrially scalable and cost effective pretreatment method is needed. Obtaining a high yield of sugar from recalcitrant biomass generally requires a high severity of pretreatment with aggressive chemistry, followed by extensive conditioning, and large doses of enzymes. Catchlight Energy's Sugar process, CLE Sugar, uses a low intensity, high throughput variation of bisulfite pulping to pretreat recalcitrant biomass, such as softwood forest residuals. By leveraging well-proven bisulfite technology and the rapid progress of enzyme suppliers, CLE Sugar can achieve a high yield of total biomass carbohydrate conversion to monomeric lignocellulosic sugars. For example, 85.8% of biomass carbohydrates are saccharified for un-debarked Loblolly pine chips (softwood), and 94.0% for debarked maple chips (hardwood). Furan compound formation was 1.29% of biomass feedstock for Loblolly pine and 1.10% for maple. At 17% solids hydrolysis of pretreated softwood, an enzyme dose of 0.075 g Sigma enzyme mixture/g dry pretreated (unwashed) biomass was needed to achieve 8.1% total sugar titer in the hydrolysate and an overall prehydrolysate liquor plus enzymatic hydrolysis conversion yield of 76.6%. At a much lower enzyme dosage of 0.044 g CTec2 enzyme product/g dry (unwashed) pretreated softwood, hydrolysis at 17% solids achieved 9.2% total sugar titer in the hydrolysate with an overall sugar yield of 85.0% in the combined prehydrolysate liquor and enzymatic hydrolysate. CLE Sugar has

  10. Role of centralized review processes for making reimbursement decisions on new health technologies in Europe

    Directory of Open Access Journals (Sweden)

    Stafinski T

    2011-08-01

    Full Text Available Tania Stafinski1, Devidas Menon2, Caroline Davis1, Christopher McCabe31Health Technology and Policy Unit, 2Health Policy and Management, School of Public Health, University of Alberta, Edmonton, Alberta, Canada; 3Academic Unit of Health Economics, Leeds Institute for Health Sciences, University of Leeds, Leeds, UKBackground: The purpose of this study was to compare centralized reimbursement/coverage decision-making processes for health technologies in 23 European countries, according to: mandate, authority, structure, and policy options; mechanisms for identifying, selecting, and evaluating technologies; clinical and economic evidence expectations; committee composition, procedures, and factors considered; available conditional reimbursement options for promising new technologies; and the manufacturers' roles in the process.Methods: A comprehensive review of publicly available information from peer-reviewed literature (using a variety of bibliographic databases and gray literature (eg, working papers, committee reports, presentations, and government documents was conducted. Policy experts in each of the 23 countries were also contacted. All information collected was reviewed by two independent researchers.Results: Most European countries have established centralized reimbursement systems for making decisions on health technologies. However, the scope of technologies considered, as well as processes for identifying, selecting, and reviewing them varies. All systems include an assessment of clinical evidence, compiled in accordance with their own guidelines or internationally recognized published ones. In addition, most systems require an economic evaluation. The quality of such information is typically assessed by content and methodological experts. Committees responsible for formulating recommendations or decisions are multidisciplinary. While criteria used by committees appear transparent, how they are operationalized during deliberations

  11. Technology options for clean coal power generation with CO2 capture

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Song; Bergins, Christian; Kikkawa, Hirofumi; Kobayashi, Hironobu; Kawasaki, Terufumi

    2010-09-15

    The state-of-the-art coal-fired power plant today is about 20% more efficient than the average operating power plants, and can reduce emissions such as SO2, NOx, and mercury to ultra-low levels. Hitachi is developing a full portfolio of clean coal technologies aimed at further efficiency improvement, 90% CO2 reduction, and near-zero emissions, including 700 deg C ultrasupercritical boilers and turbines, post-combustion CO2 absorption, oxyfuel combustion, and IGCC with CCS. This paper discusses the development status, performance and economic impacts of these technologies with focus on post combustion absorption and oxyfuel combustion - two promising CO2 solutions for new and existing power plants.

  12. Motor Drive Technologies for the Power-by-Wire (PBW) Program: Options, Trends and Tradeoffs

    Science.gov (United States)

    Elbuluk, Malik E.; Kankam, M. David

    1995-01-01

    Power-By-Wire (PBW) is a program involving the replacement of hydraulic and pneumatic systems currently used in aircraft with an all-electric secondary power system. One of the largest loads of the all-electric secondary power system will be the motor loads which include pumps, compressors and Electrical Actuators (EA's). Issues of improved reliability, reduced maintenance and efficiency, among other advantages, are the motivation for replacing the existing aircraft actuators with electrical actuators. An EA system contains four major components. These are the motor, the power electronic converters, the actuator and the control system, including the sensors. This paper is a comparative literature review in motor drive technologies, with a focus on the trends and tradeoffs involved in the selection of a particular motor drive technology. The reported research comprises three motor drive technologies. These are the induction motor (IM), the brushless dc motor (BLDCM) and the switched reluctance motor (SRM). Each of the three drives has the potential for application in the PBW program. Many issues remain to be investigated and compared between the three motor drives, using actual mechanical loads expected in the PBW program.

  13. The hardness of the nuclear option in the Netherlands. A study on the occurrence of an abused technology

    International Nuclear Information System (INIS)

    Van Vugt, F.

    2004-01-01

    The central theme in this master's thesis is the tension between attempts aimed at phasing out the nuclear option and the resistance of the implied sociotechnical structures to this fundamental change. Nuclear option is the choice of a particular country for the generation of electricity by means of nuclear fission. This study is inspired by an empirical question: why is the intention of certain countries to phase out the nuclear option so difficult to realize. This intention is constantly the object of debate. This is shown by the delay of the planned decommissioning of the Barsebaeck-plant in Sweden, the statements of the director of Electrabel (the company that manages the Belgian nuclear plants) that the plants will not be closed on the dates that were dictated by the Belgian government and by the fact that the Borssele-plant in the Netherlands is still up and running despite a parliamentary decree dictating the closure of the plant on 31st of December 2003. Did policymakers responsible for the decision to phase out make a mistake concerning the constructability of reality? Why is it so difficult to change the technological status quo? What factors play a role in this resistance? These questions form the core of this study. To answer these questions use is made of the theoretical work of Anique Hommels. In her doctoral thesis (Unbuilding Cities: Obduracy in Urban Sociotechnical Change) she poses similar questions in relation to urban structures. Why are certain urban structures so hard to change? This resistance to change is expressed in the notion of obduracy. Hommels identifies four causations of this obduracy, which she expresses in four theoretical categories: (1) material obduracy, (2) obduracy caused by dominant ways of thinking, (3) obduracy as constituted by embeddedness, and (4) obduracy explained by persistent traditions. These notions are derived from the interdisciplinary research field of Science Technology and Society studies (STS). In this report

  14. Heat integration options based on pinch and exergy analyses of a thermosolar and heat pump in a fish tinning industrial process

    International Nuclear Information System (INIS)

    Quijera, José Antonio; García, Araceli; Alriols, María González; Labidi, Jalel

    2013-01-01

    Thermosolar technology is being inserted gradually in industrial activities. In order to reach high energy efficiency, thermosolar can be linked to heat pump technology, combining more efficient conventional and renewable energy support for processes. Their integration in complex processes can be improved systematically through well established analytical tools, like pinch and exergy analyses. This work presents a methodological procedure for the analysis of different options of heat integration of a solar thermal and heat pump technologies in a tuna fish tinning process. The plant is located in a climatic zone where diffuse irradiation contributes more energy to the process than beam irradiation does. Pinch and exergy analyses are applied in the context of a low and middle temperatures, where the process demands big amounts of hot water and middle pressure steam. In order to recover internal heat, pinch analysis allows to understand the complexity of the heat exchange network of the process and to define thermal tendency objectives for energy optimization. Exergy analysis quantifies the variation that the quality of energy undergoes while it is used in the process according to the different way of integration. Both analytical tools, in combination with economical variables, provide a powerful methodological procedure finding the most favourable heat integration and, by this, they help in the technological decision making and in the design phase. - Highlights: ► Integration of solar thermal energy in batch canning process was assessed. ► Pinch and exergy analyses were used to determine the optimal energy supply configuration. ► Combination of heat pump and solar thermal energy improves the energy efficiency and reduces fossil fuel consumption

  15. Integrated modelling in materials and process technology

    DEFF Research Database (Denmark)

    Hattel, Jesper Henri

    2008-01-01

    Integrated modelling of entire process sequences and the subsequent in-service conditions, and multiphysics modelling of the single process steps are areas that increasingly support optimisation of manufactured parts. In the present paper, three different examples of modelling manufacturing...... processes from the viewpoint of combined materials and process modelling are presented: solidification of thin walled ductile cast iron, integrated modelling of spray forming and multiphysics modelling of friction stir welding. The fourth example describes integrated modelling applied to a failure analysis...

  16. Novel technologies for the lost foam casting process

    Science.gov (United States)

    Jiang, Wenming; Fan, Zitian

    2018-03-01

    Lost foam casting (LFC) is a green precision casting process categorized as a near net forming technology. Yet, despite its popularity, it still suffers from some technological problems, such as poor filling ability of the castings, coarse and non-dense microstructure, low mechanical properties for the Al and Mg LFC processes, and defective carburization for the low carbon steel LFC process. These drawbacks restrict the development and widespread application of the LFC process. To solve these problems, the present study developed several novel LFC technologies, namely, LFC technologies under vacuum and low pressure, vibration solidification, and pressure solidification conditions; expendable shell casting technology; and preparation technology of bimetallic castings based on the LFC process. The results showed that the LFC under vacuum and low pressure evidently improved the filling ability and solved the oxidization problem of the alloys, which is suitable for producing complex and thinwall castings. The vibration and pressure solidifications increased the compactness of the castings and refined the microstructure, significantly improving the mechanical properties of the castings. The expendable shell casting technology could solve the pore, carburization, and inclusion defects of the traditional LFC method, obtaining castings with acceptable surface quality. Moreover, the Al/Mg and Al/Al bimetallic castings with acceptable metallurgical bonding were successfully fabricated using the LFC process. These proposed novel LFC technologies can solve the current technological issues and promote the technological progress of the LFC process.

  17. Optimization of processing technology of Rhizoma Pinelliae ...

    African Journals Online (AJOL)

    The fundamental purpose for processing tra- ditional Chinese Medicine is to attenuate toxicity and enhance efficacy. The processing of Rhizoma Pinelliae. Praeparatum is a typical representative. Through dif- ferent approaches of processing, toxic constituents of. Rhizoma Pinelliae are reduced, thus extending its range.

  18. Optimization of processing technology of Rhizoma Pinelliae ...

    African Journals Online (AJOL)

    and Alum', General Records", processing with licorice and ginger in "Zhu Shi", Ming Dynasty's processing- with licorice and lime in the "Compendium of Mate- ria Medica", and processing with ethanol and ginger in the "Prescriptions for Universal Relief", Qing Dynas- ty's "Supplement to Compendium of Materia Medica".

  19. Technological options for management of NORM/TENORM from the petroleum exploration

    International Nuclear Information System (INIS)

    Miranda, Marcia Valeria Sa; Gomes, Joana D'Arc L.; Crispim, Verginia R.

    2008-01-01

    Full text: Naturally Occurring Radioactive Material (NORM) is present in many natural resources and the contamination of oil and gas facilities with it can be expected. Some of the contamination may be sufficiently severe that maintenance and other personnel may be exposed to hazardous concentrations, at the production line. Because of this, its management shall be efficient and optimized. The measure adopted to achieve successful management will be in accordance with general environmental and safety objectives and will involve the application of best available techniques and best environmental safety practices. The disposal of NORM contaminated wastes is a problem with no completely satisfactory solution yet. NORM contamination in the oil and gas industry commonly occurs as radioactive scales, films and sludge. The resulting of the decontamination of petroleum production facilities can generate large volumes of NORM wastes. These materials require the same handling as low-level radioactive wastes. The cost of storing or disposing material contaminated with NORM is undoubtedly very expensive. The high cost of disposing of NORM wastes is opening new opportunities for research and development in methods and techniques of reducing waste volumes. The aim of this paper is present some considerations of possible NORM management/disposal options and show some samples analysis. The objective is to find appropriated solutions to the management/disposal of NORM wastes to prevent pollution of the environment and minimize public and occupational radiation exposure. NORM can be dealt with safely, efficiently and with minimized risks to the health of workers and the public while providing optimized environmental protection. Techniques as encapsulation, down hole injection, overboard disposal with produced formation water, landfill disposal including burial, land disposal in abandoned mine and interim storage in a dedicated facility pending ultimate disposal, are discussed from a

  20. Advanced Manufacturing Office Clean Water Processing Technologies

    Energy Technology Data Exchange (ETDEWEB)

    None

    2018-03-01

    The DOE Office of Energy Efficiency and Renewable Energy (EERE)’s Advanced Manufacturing Office partners with industry, small business, universities, and other stakeholders to identify and invest in emerging technologies with the potential to create high-quality domestic manufacturing jobs and enhance the global competitiveness of the United States.

  1. Partitioning-transmutation technology: a potential future nuclear waste management option

    International Nuclear Information System (INIS)

    Nakayama, S.; Morita, Y.; Nishihara, K.; Oigawa, H.

    2005-01-01

    Partitioning-transmutation technology (PT) will produce radioactive wastes of different physical and chemical properties and in different amounts from those generated in the current nuclear fuel cycle. To assess quantitatively the effects of PT on waste disposal, we first analyzed the amounts of the PT wastes, assumed conditioning for each type of the waste, and then made an attempt to estimate the repository area for disposal of the PT wastes. The properties of the hot Sr-Cs waste form are controlling factors in determining the size of the geologic repository. The disposal area could be reduced if the Sr-Cs fraction is disposed in a different subsurface repository or by long-term storage of the waste under institutional control. Disposal in a subsurface repository was found to comply with the Japanese law in terms of radioactivity constraint, through a performance assessment for disposal of the Sr-Cs fraction. (authors)

  2. Radiation Evaluation and Concept Development for Analog Probability Processing Technology

    Data.gov (United States)

    National Aeronautics and Space Administration — Analog probability processing technology has the ability to provide game-changing performance advances and power savings for on-board data processing applications....

  3. FY97 Materials & Processes Technology Area Plan

    Science.gov (United States)

    1996-09-01

    preproduction ability. Concentrator with Refractive verdsion engines. Trimarc is "--To meet 1700*F - 2800*F Linear Element Technology). 40% lighter than...graph- can also be used as acuators for tios of 1986 engine per- ite foams for structures. ailerons, flaps and landing gear formance baseline...Aerial Aluminum Garnet SCARLET - Solar Concentrator Vehicle Ni - Nickel with Refractive Linear Ele- UHF - Ultra High Frequency NLO - Nonlinear Optical or

  4. Refining processes in the copper casting technology

    OpenAIRE

    Rzadkosz, S.; Kranc, M.; Garbacz-Klempka, A.; Kozana, J.; Piękoś, M.

    2015-01-01

    The paper presents the analysis of technology of copper and alloyed copper destined for power engineering casts. The casts quality was assessed based on microstructure, chemical content analysis and strength properties tests. Characteristic deoxidising (Logas, Cup) and modifying (ODM2, Kupmod2) formulas were used for the copper where high electrical conductivity was required. Chosen examples of alloyed copper with varied Cr and Zr content were studied, and the optimal heat treatment parameter...

  5. Managing Technological Change: The Process is Key

    Science.gov (United States)

    1989-01-01

    performance suggestive of an electronic sweatshop or informa- and the quality of their work lives has been significantly im- tion assembly line than a...changc the rescrvations system, but without docu- systems, databases, and software applications that comprise mentation or access to the person who...and task HAS BEEN SEEN that instead of trying to minimize change. level, the technology’s inherent flexibili- AS A ITATI particularly with respect to

  6. Defense Waste Processing Facility: Report of task force on options to mitigate the effect of nitrite on DWPF operations

    Energy Technology Data Exchange (ETDEWEB)

    Randall, D. (ed.); Marek, J.C.

    1992-03-01

    The possibility of accumulating ammonium nitrate (an explosive) as well as organic compounds in the DWPF Chemical Processing Cell Vent System was recently discovered. A task force was therefore organized to examine ways to avoid this potential hazard. Of thirty-two processing/engineering options screened, the task force recommended five options, deemed to have the highest technical certainty, for detailed development and evaluation: Radiolysis of nitrite in the tetraphenylborate precipitate slurry feed in a new corrosion-resistant facility. Construction of a Late Washing Facility for precipitate washing before transfer to the DWPF; Just-in-Time'' precipitation; Startup Workaround by radiolysis of nitrite in the existing corrosion-resistant Pump Pit tanks; Ammonia venting and organics separation in the DWPF; and, Estimated costs and schedules are included in this report.

  7. Application of supercritical carbon dioxide extrusion in food processing technology

    OpenAIRE

    Panak-Balentić Jelena; Ačkar Đurđica; Jozinović Antun; Babić Jurislav; Miličević Borislav; Jokić Stela; Pajin Biljana; Šubarić Drago

    2017-01-01

    Extrusion process is one of the most important innovations of the 20th century applied in many industries. Extrusion is a technology that is increasingly used for the production of various food products, especially snacks and breakfast cereals. Supercritical carbon dioxide (CO2) as a non-toxic, non-flammable and inexpensive, is applied in many processes, including the extrusion technology. Supercritical CO2 extrusion process (SCFX) found its application primarily in the processing and manufac...

  8. Energy and Cost Optimized Technology Options to Meet Energy Needs of Food Processors

    Energy Technology Data Exchange (ETDEWEB)

    Makhmalbaf, Atefe; Srivastava, Viraj; Hoffman, Michael G.; Wagner, Anne W.; Thornton, John

    2015-04-02

    ABSTRACT Combined cooling, heating and electric power (CCHP) distributed generation (DG) systems can provide electricity, heat, and cooling power to buildings and industrial processes directly onsite, while significantly increasing energy efficiency, security of energy supply, and grid independence. Fruit, vegetable, dairy and meat processing industries with simultaneous requirements for heat, steam, chilling and electricity, are well suited for the use of such systems to supply base-load electrical demand or as peak reducing generators with heat recovery in the forms of hot water, steam and/or chilled water. This paper documents results and analysis from a pilot project to evaluate opportunities for energy, emission, and cost for CCHP-DG and energy storage systems installed onsite at food processing facilities. It was found that a dairy processing plant purchasing 15,000 MWh of electricity will need to purchase 450 MWh with the integration of a 1.1 MW CCHP system. Here, the natural gas to be purchased increased from 190,000 MMBtu to 255,000 MMBtu given the fuel requirements of the CCHP system. CCHP systems lower emissions, however, in the Pacific Northwest the high percentage of hydro-power results in CO2 emissions from CCHP were higher than that attributed to the electric utility/regional energy mix. The value of this paper is in promoting and educating financial decision makers to seriously consider CCHP systems when building or upgrading facilities. The distributed generation aspect can reduce utility costs for industrial facilities and show non-wires solution benefits to delay or eliminate the need for upgrades to local electric transmission and distribution systems.

  9. Hybrid process technologies in the financial sector

    DEFF Research Database (Denmark)

    Debois, Søren; Hildebrandt, Thomas; Marquard, Morten

    2015-01-01

    the variants of the process that are relevant to them. This paper reports on a project we undertook with such a credit institute where we investigated and addressed these issues by providing a hybrid solution, allowing processes to be modelled using our constraint-based modelling tools, but also supporting...

  10. Thermodynamics for separation-process technology

    Energy Technology Data Exchange (ETDEWEB)

    Prausnitz, J.M.

    1995-10-01

    When contemplating or designing a separation process, every chemical engineer at once recognizes the thermodynamic boundary conditions that must be satisfied: when a mixture is continuously processed to yield at least partially purified products, energy and mass must be conserved and work must be done. In his daily tasks, a chemical engineer uses thermodynamic concepts as tacit, almost subconscious, knowledge. Thus, qualitative thermodynamics significantly informs process conception at its most fundamental level. However, quantitative design requires detailed knowledge of thermodynamic relations and physical chemistry. Most process engineers, concerned with flow sheets and economics, cannot easily command that detailed knowledge and therefore it is advantageous for them to maintain close contact with those specialists who do. Quantitative chemical thermodynamics provides an opportunity to evaluate possible separation processes not only because it may give support to the process engineer`s bold imagination but also because, when coupled with molecular models, it can significantly reduce the experimental effort required to determine an optimum choice of process alternatives. Six examples are presented to indicate the application of thermodynamics for conventional and possible future separation processes.

  11. Semantic Technology Recommendation Based on the Analytic Network Process

    OpenAIRE

    Radulovic, F.; García-Castro, Raúl

    2012-01-01

    Semantic technologies have become widely adopted in recent years, and choosing the right technologies for the problems that users face is often a difficult task. This paper presents an application of the Analytic Network Process for the recommendation of semantic technologies, which is based on a quality model for semantic technologies. Instead of relying on expert-based comparisons of alternatives, the comparisons in our framework depend on real evaluation results. Furthermore, the recommend...

  12. Design options for HLW repository operation technology. (2) Bentonite block forming and vertical emplacement

    International Nuclear Information System (INIS)

    Takao, Hajime; Takegahara, Tatsuhiro; Nakashima, Hitoshi; Asano, Hidekazu

    2011-01-01

    RWMC and JGC have been running an all-round R and D program for the period of 2000-2010 to develop the concept of Vertical Emplacement for disposal of vitrified waste. The conceptual design of its basic equipment was worked out in 2000, followed by forming the large-scale bentonite block in 2001-2004. Study has also been conducted on a mechanism to convey and position the large-scale block using a vacuum suction device. Subsequent to these developments, various technologies necessary for designing the Vertical Emplacement equipment have been reviewed, which would enhance engineering feasibility and reliability. Full-scale demonstration program under a joint research program with JAEA (Japan Atomic Energy Agency) started in 2008 with the twin objectives 1) supporting of public relations and 2) technical verification. The large-scale bentonite block and part of the full-scale Vertical Emplacement equipment are now on view at the Full-scale demonstration facility in Horonobe, Hokkaido, Japan. (author)

  13. Analyzing Neutrophil Morphology, Mechanics, and Motility in Sepsis: Options and Challenges for Novel Bedside Technologies.

    Science.gov (United States)

    Zonneveld, Rens; Molema, Grietje; Plötz, Frans B

    2016-01-01

    Alterations in neutrophil morphology (size, shape, and composition), mechanics (deformability), and motility (chemotaxis and migration) have been observed during sepsis. We combine summarizing features of neutrophil morphology, mechanics, and motility that change during sepsis with an investigation into their clinical utility as markers for sepsis through measurement with novel technologies. We performed an initial literature search in MEDLINE using search terms "neutrophil," "morphology," "mechanics," "dynamics," "motility," "mobility," "spreading," "polarization," "migration," and "chemotaxis." We then combined the results with "sepsis" and "septic shock." We scanned bibliographies of included articles to identify additional articles. Final selection was done after the authors reviewed recovered articles. We included articles based on their relevance for our review topic. When compared with resting conditions, sepsis causes an increase in circulating numbers of larger, more rigid neutrophils that show diminished granularity, migration, and chemotaxis. Combined measurement of these variables could provide a more complete view on neutrophil phenotype manifestation. For that purpose, sophisticated automated hematology analyzers, microscopy, and bedside microfluidic devices provide clinically feasible, high-throughput, and cost-limiting means. We propose that integration of features of neutrophil morphology, mechanics, and motility with these new analytical methods can be useful as markers for diagnosis, prognosis, and monitoring of sepsis and may even contribute to basic understanding of its pathophysiology.

  14. A Survey on Evaluation Factors for Business Process Management Technology

    NARCIS (Netherlands)

    Mutschler, B.B.; Reichert, M.U.

    2006-01-01

    Estimating the value of business process management (BPM) technology is a difficult task to accomplish. Computerized business processes have a strong impact on an organization, and BPM projects have a long-term cost amortization. To systematically analyze BPM technology from an economic-driven

  15. Energy and Cost Optimized Technology Options to Meet Energy Needs of Food Processors

    Energy Technology Data Exchange (ETDEWEB)

    Makhmalbaf, Atefe; Srivastava, Viraj; Hoffman, Michael G.; Wagner, Anne W.; Thornton, John

    2015-05-01

    Full Paper Submission for: Combined cooling, heating and electric power (CCHP) distributed generation (DG) systems can provide electric power and, heating and cooling capability to commercial and industrial facilities directly onsite, while increasing energy efficiency, security of energy supply, grid independence and enhancing the environmental and economic situation for the site. Food processing industries often have simultaneous requirements for heat, steam, chilling and electricity making them well suited for the use of such systems to supply base-load or as peak reducing generators enabling reduction of overall energy use intensity. This paper documents analysis from a project evaluating opportunities enabled by CCHPDG for emission and cost reductions and energy storage systems installed onsite at food processing facilities. In addition, this distributed generation coupled with energy storage demonstrates a non-wires solution to delay or eliminate the need for upgrades to electric distribution systems. It was found that a dairy processing plant in the Pacific Northwest currently purchasing 15,000 MWh/yr of electricity and 190,000 MMBtu/yr of gas could be provided with a 1.1 MW CCHP system reducing the amount of electric power purchased to 450 MWh/yr while increasing the gas demand to 255,000 MMBtu/yr. The high percentage of hydro-power in this region resulted in CO2 emissions from CCHP to be higher than that attributed to the electric utility/regional energy mix. The value of this work is in documenting a real-world example demonstrating the value of CCHP to facility owners and financial decision makers to encourage them to more seriously consider CCHP systems when building or upgrading facilities.

  16. Greenhouse Emission Reductions and Natural Gas Vehicles: A Resource Guide on Technology Options and Project Development

    Energy Technology Data Exchange (ETDEWEB)

    Orestes Anastasia; NAncy Checklick; Vivianne Couts; Julie Doherty; Jette Findsen; Laura Gehlin; Josh Radoff

    2002-09-01

    Accurate and verifiable emission reductions are a function of the degree of transparency and stringency of the protocols employed in documenting project- or program-associated emissions reductions. The purpose of this guide is to provide a background for law and policy makers, urban planners, and project developers working with the many Greenhouse Gas (GHG) emission reduction programs throughout the world to quantify and/or evaluate the GHG impacts of Natural Gas Vehicle (NGVs). In order to evaluate the GHG benefits and/or penalties of NGV projects, it is necessary to first gain a fundamental understanding of the technology employed and the operating characteristics of these vehicles, especially with regard to the manner in which they compare to similar conventional gasoline or diesel vehicles. Therefore, the first two sections of this paper explain the basic technology and functionality of NGVs, but focus on evaluating the models that are currently on the market with their similar conventional counterparts, including characteristics such as cost, performance, efficiency, environmental attributes, and range. Since the increased use of NGVs, along with Alternative Fuel Vehicle (AFVs) in general, represents a public good with many social benefits at the local, national, and global levels, NGVs often receive significant attention in the form of legislative and programmatic support. Some states mandate the use of NGVs, while others provide financial incentives to promote their procurement and use. Furthermore, Federal legislation in the form of tax incentives or procurement requirements can have a significant impact on the NGV market. In order to implement effective legislation or programs, it is vital to have an understanding of the different programs and activities that already exist so that a new project focusing on GHG emission reduction can successfully interact with and build on the experience and lessons learned of those that preceded it. Finally, most programs

  17. Conjoint Management of Business Processes and Information Technologies

    DEFF Research Database (Denmark)

    Siurdyban, Artur

    and improve business processes. As a consequence, there is a growing need to address managerial aspects of the relationships between information technologies and business processes. The aim of this PhD study is to investigate how the practice of conjoint management of business processes and information...... technologies can be supported and improved. The study is organized into five research papers and this summary. Each paper addresses a different aspect of conjoint management of business processes and information technologies, i.e. problem development and managerial practices on software...... and information technologies in a project environment. It states that both elements are intrinsically related and should be designed and considered together. The second case examines the relationships between information technology management and business process management. It discusses the multi-faceted role...

  18. The Potential Use of Intrauterine Insemination as a Basic Option for Infertility: A Review for Technology-Limited Medical Settings

    Directory of Open Access Journals (Sweden)

    Abdelrahman M. Abdelkader

    2009-01-01

    Full Text Available Objective. There is an asymmetric allocation of technology and other resources for infertility services. Intrauterine insemination (IUI is a process of placing washed spermatozoa transcervically into the uterine cavity for treatment of infertility. This is a review of literature for the potential use of IUI as a basic infertility treatment in technology-limited settings. Study design. Review of articles on treatment of infertility using IUI. Results. Aspects regarding the use of IUI are reviewed, including ovarian stimulation, semen parameters associated with good outcomes, methods of sperm preparation, timing of IUI, and number of inseminations. Implications of the finding in light of the needs of low-technology medical settings are summarized. Conclusion. The reviewed evidence suggests that IUI is less expensive, less invasive, and comparably effective for selected patients as a first-line treatment for couples with unexplained or male factor infertility. Those couples may be offered three to six IUI cycles in technology-limited settings.

  19. COMPLEX PROCESSING TECHNOLOGY OF TOMATO RAW MATERIALS

    OpenAIRE

    A. M. Gadzhieva; G. I. Kasianov

    2015-01-01

    Tomatoes grown in the central and southern parts of the country, which contain 5-6 % of solids, including 0.13 % of pectin, 0.86 % of fat, 0.5 % of organic acids; 0.5 % minerals, etc. were used as a subject of research. These tomatoes, grown in the mountains, on soils with high salinity, contain high amounts of valuable components and have a long-term preservation. For the extraction of valuable components from dried tomato pomace CO2 extraction method was applied. Technological and environm...

  20. Modeling of processing technologies in food industry

    Science.gov (United States)

    Korotkov, V. G.; Sagitov, R. F.; Popov, V. P.; Bachirov, V. D.; Akhmadieva, Z. R.; TSirkaeva, E. A.

    2018-03-01

    Currently, the society is facing an urgent need to solve the problems of nutrition (products with increased nutrition value) and to develop energy-saving technologies for food products. A mathematical modeling of heat and mass transfer of polymer materials in the extruder is rather successful these days. Mathematical description of movement and heat exchange during extrusion of gluten-protein-starch-containing material similar to pasta dough in its structure, were taken as a framework for the mathematical model presented in this paper.

  1. Best available technology equivalent controls for B Plant Process Condensate: Tank farm process technology section

    International Nuclear Information System (INIS)

    1988-11-01

    This report evaluates whether proposed controls for the B Plant Process Condensate effluent stream are equivalent to Best Available Technology (BAT) economically achievable. Methods to determine whether the proposed controls for the BCP were equivalent to BAT originated from the Guidance Document for the Hanford Site. The BAT performance standards, which originate from the Clean Water Act, are to be applied to all contaminated liquid effluent discharges currently going to the soil column at the Hanford Site. The B Plant BAT evaluation addressed pollutants that had not been regulated traditionally under Federal or State water-pollution control programs. As a result, only comparisons could be made to existing radiation and water quality standards, and a BAT determination based on the effluent guidelines method (as outlined in the BAT Guidance Document) was not possible. Due to the variability and inconsistency of factors with comparable streams, such as the effluent stream at the Savannah River Plant, a BAT determination by the technology transfer method and treatability studies method was not possible. By using the generic treatment systems method, a one-or two-stage treatment system for dissolved solids removal was concluded to be equivalent to BAT. By performing two economic achievability tests, a one-stage treatment system consisting of mixed bed ion exchange columns was considered to be cost effective and equivalent to BAT. 13 refs., 4 figs., 5 tabs

  2. FY-2010 Process Monitoring Technology Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Orton, Christopher R.; Bryan, Samuel A.; Casella, Amanda J.; Hines, Wes; Levitskaia, Tatiana G.; henkell, J.; Schwantes, Jon M.; Jordan, Elizabeth A.; Lines, Amanda M.; Fraga, Carlos G.; Peterson, James M.; Verdugo, Dawn E.; Christensen, Ronald N.; Peper, Shane M.

    2011-01-01

    During FY 2010, work under the Spectroscopy-Based Process Monitoring task included ordering and receiving four fluid flow meters and four flow visible-near infrared spectrometer cells to be instrumented within the centrifugal contactor system at Pacific Northwest National Laboratory (PNNL). Initial demonstrations of real-time spectroscopic measurements on cold-stream simulants were conducted using plutonium (Pu)/uranium (U) (PUREX) solvent extraction process conditions. The specific test case examined the extraction of neodymium nitrate (Nd(NO3)3) from an aqueous nitric acid (HNO3) feed into a tri-n-butyl phosphate (TBP)/ n-dodecane solvent. Demonstration testing of this system included diverting a sample from the aqueous feed meanwhile monitoring the process in every phase using the on-line spectroscopic process monitoring system. The purpose of this demonstration was to test whether spectroscopic monitoring is capable of determining the mass balance of metal nitrate species involved in a cross-current solvent extraction scheme while also diverting a sample from the system. The diversion scenario involved diverting a portion of the feed from a counter-current extraction system while a continuous extraction experiment was underway. A successful test would demonstrate the ability of the process monitoring system to detect and quantify the diversion of material from the system during a real-time continuous solvent extraction experiment. The system was designed to mimic a PUREX-type extraction process with a bank of four centrifugal contactors. The aqueous feed contained Nd(NO3)3 in HNO3, and the organic phase was composed of TBP/n-dodecane. The amount of sample observed to be diverted by on-line spectroscopic process monitoring was measured to be 3 mmol (3 x 10-3 mol) Nd3+. This value was in excellent agreement with the 2.9 mmol Nd3+ value based on the known mass of sample taken (i.e., diverted) directly from the system feed solution.

  3. Application of thermal technologies for processing of radioactive waste

    International Nuclear Information System (INIS)

    2006-12-01

    The primary objective of this publication is to provide an overview of the various thermal technologies for processing various solid, liquid, organic and inorganic radioactive waste streams. The advantages, limitations and operating experience of various thermal technologies are explained. This publication also goes beyond previous work on thermal processes by addressing the applicability of each technology to national or regional nuclear programmes of specific relative size (major advanced programmes, small to medium programmes, and emerging programmes with other nuclear applications). The most commonly used thermal processing technologies are reviewed, and the key factors influencing the selection of thermal technologies as part of a national waste management strategy are discussed. Accordingly, the structure and content of this publication is intended to assist decision-makers, regulators, and those charged with developing such strategies to identify and compare thermal technologies for possible inclusion in the mix of available, country-specific waste management processes. This publication can be used most effectively as an initial cutting tool to identify whether any given technology will best serve the local waste management strategy in terms of the waste generated, technical complexity, available economic resources, environmental impact considerations, and end product (output) of the technology. If multiple thermal technologies are being actively considered, this publication should be instrumental in comparing the technologies and assisting the user to reach an informed decision based on local needs, economics and priorities. A detailed set of conclusions is provided in Section 7

  4. Risk calculations in the manufacturing technology selection process

    DEFF Research Database (Denmark)

    Farooq, S.; O'Brien, C.

    2010-01-01

    and supports an industrial manager in achieving objective and comprehensive decisions regarding selection of a manufacturing technology. Originality/value - The paper explains the process of risk calculation in manufacturing technology selection by dividing the decision-making environment into manufacturing...... in the shape of opportunities and threats in different decision-making environments. Practical implications - The research quantifies the risk associated with different available manufacturing technology alternatives. This quantification of risk crystallises the process of technology selection decision making......Purpose - The purpose of this paper is to present result obtained from a developed technology selection framework and provide a detailed insight into the risk calculations and their implications in manufacturing technology selection process. Design/methodology/approach - The results illustrated...

  5. Process for making unsaturated hydrocarbons using microchannel process technology

    Science.gov (United States)

    Tonkovich, Anna Lee [Dublin, OH; Yuschak, Thomas [Lewis Center, OH; LaPlante, Timothy J [Columbus, OH; Rankin, Scott [Columbus, OH; Perry, Steven T [Galloway, OH; Fitzgerald, Sean Patrick [Columbus, OH; Simmons, Wayne W [Dublin, OH; Mazanec, Terry Daymo, Eric

    2011-04-12

    The disclosed invention relates to a process for converting a feed composition comprising one or more hydrocarbons to a product comprising one or more unsaturated hydrocarbons, the process comprising: flowing the feed composition and steam in contact with each other in a microchannel reactor at a temperature in the range from about 200.degree. C. to about 1200.degree. C. to convert the feed composition to the product, the process being characterized by the absence of catalyst for converting the one or more hydrocarbons to one or more unsaturated hydrocarbons. Hydrogen and/or oxygen may be combined with the feed composition and steam.

  6. Application of membrane technologies for liquid radioactive waste processing

    International Nuclear Information System (INIS)

    2004-01-01

    Membrane separation processes have made impressive progress since the first synthesis of membranes almost 40 years ago. This progress was driven by strong technological needs and commercial expectations. As a result the range of successful applications of membranes and membrane processes is continuously broadening. In addition, increasing application of membrane processes and technologies lies in the increasing variations of the nature and characteristics of commercial membranes and membrane apparatus. The objective of the report is to review the information on application of membrane technologies in the processing of liquid radioactive waste. The report covers the various types of membranes, equipment design, range of applications, operational experience and the performance characteristics of different membrane processes. The report aims to provide Member States with basic information on the applicability and limitations of membrane separation technologies for processing liquid radioactive waste streams

  7. Refining processes in the copper casting technology

    Directory of Open Access Journals (Sweden)

    S. Rzadkosz

    2015-01-01

    Full Text Available The paper presents the analysis of technology of copper and alloyed copper destined for power engineering casts. The casts quality was assessed based on microstructure, chemical content analysis and strength properties tests. Characteristic deoxidising (Logas, Cup and modifying (ODM2, Kupmod2 formulas were used for the copper where high electrical conductivity was required. Chosen examples of alloyed copper with varied Cr and Zr content were studied, and the optimal heat treatment parameters were tested for a chosen chromium copper content, based on the criterion of hardness and electrical conductivity tests. Searching for materials with high wear resistance, the influence of variable silicone content on the properties of CuNiSi alloy was researched.

  8. Results of the IAEA CRP on studies of advanced reactor technology options for effective incineration of radioactive waste

    International Nuclear Information System (INIS)

    Maschek, W.; Stanculescu, A.; ); Gopalakrishnan, V.

    2007-01-01

    The IAEA has initiated a Coordinated Research Project (CRP) on 'Studies of Advanced Reactor Technology Options for Effective Incineration of Radioactive Waste'. The overall objective of the CRP, performed within the framework of IAEA's Nuclear Power Technology Development Section's Technical Working Group on Fast Reactors (TWG-FR), is to increase the capability of Member States in developing and applying advanced technologies in the area of long-lived radioactive waste utilization and transmutation. More specifically, the final goal of the CRP is to deepen the understanding of the dynamics of transmutation systems, especially systems with high minor actinide content. Currently, 20 institutions from 15 member states and one international organization are participating in this CRP. The current author list comprises the participants of the last CRP Vienna meeting. The CRP concentrates on the assessment of the transient behaviour of various transmutation systems. For a sound assessment of the transient and accident behaviour, neutron kinetics and dynamics methods and codes have to be qualified, especially as the margins for the safety relevant neutronics parameters are generally becoming small in a transmutation system. Hence, the availability of adequate and qualified methods for the analysis of the various systems is an important point of the exercise. A benchmarking effort between the codes and nuclear data used for the analyses has been performed, which will help specifying the range of validity of methods, and also formulate requirements for future theoretical and experimental research. Should transient experiments become available during the course of the CRP, experimental benchmarking work will also be pursued

  9. Managing vulnerability to drought and enhancing livelihood resilience in sub-Saharan Africa: Technological, institutional and policy options

    Directory of Open Access Journals (Sweden)

    Bekele Shiferaw

    2014-06-01

    Full Text Available Agriculture and the economies of Sub-Saharan Africa (SSA are highly sensitive to climatic variability. Drought, in particular, represents one of the most important natural factors contributing to malnutrition and famine in many parts of the region. The overall impact of drought on a given country/region and its ability to recover from the resulting social, economic and environmental impacts depends on several factors. The economic, social and environmental impacts of drought are huge in SSA and the national costs and losses incurred threaten to undermine the wider economic and development gains made in the last few decades in the region. There is an urgent need to reduce the vulnerability of countries to climate variability and to the threats posed by climate change. This paper attempts to highlight the challenges of drought in SSA and reviews the current drought risk management strategies, especially the promising technological and policy options for managing drought risks to protect livelihoods and reduce vulnerability. The review suggests the possibilities of several ex ante and ex post drought management strategies in SSA although their effectiveness depends on agro-climatic and socio-economic conditions. Existing technological, policy and institutional risk management measures need to be strengthened and integrated to manage drought ex ante and to minimize the ex post negative effects for vulnerable households and regions. A proactive approach that combines promising technological, institutional and policy solutions to manage the risks within vulnerable communities implemented by institutions operating at different levels (community, sub-national, and national is considered to be the way forward for managing drought and climate variability.

  10. The Black-Scholes option pricing problem in mathematical finance: generalization and extensions for a large class of stochastic processes

    OpenAIRE

    Bouchaud, Jean-Philippe; Sornette, Didier

    1994-01-01

    The ability to price risks and devise optimal investment strategies in thé présence of an uncertain "random" market is thé cornerstone of modern finance theory. We first consider thé simplest such problem of a so-called "European call option" initially solved by Black and Scholes using Ito stochastic calculus for markets modelled by a log-Brownien stochastic process. A simple and powerful formalism is presented which allows us to generalize thé analysis to a large class of stochastic processe...

  11. Gasification — the process and the technology

    NARCIS (Netherlands)

    van Swaaij, Willibrordus Petrus Maria

    1981-01-01

    Thermochemical gasification of biomass can produce low, medium and high calorific value gases. The characteristics, applications and potential of the different processes and reactor types are discussed. The introduction of biomass gasification on a large or intermediate scale for the production of

  12. Educational Design and Construction: Processes and Technologies

    NARCIS (Netherlands)

    McKenney, Susan; Reeves, Thomas C.; Gros, Begona; Kinshuk,; Maina, Marcelo

    2015-01-01

    There are no one-size-fits-all steps for tackling different design challenges within the context of education. There are, however, processes and activities that are often useful. Developing a repertoire so that designers can select and use the most fruitful and fitting approaches for specific

  13. On the Benefit of Using Mobile Technologies in Business Processes

    OpenAIRE

    Deibert, Sina; Rothlauf, Franz

    2006-01-01

    The rapid technical progress in the development of mobile devices and technologies offers new possibilities for improving and streamlining the performance of business processes. However, only few successful mobile applications exist in the business area. This paper discusses the benefits an enterprise can gain by using mobile technologies in business processes. It presents general indicators to measure the performance of business processes and shows how these indicators must be adapted to be ...

  14. Technology Summary Advancing Tank Waste Retrieval And Processing

    International Nuclear Information System (INIS)

    Sams, T.L.; Mendoza, R.E.

    2010-01-01

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them. This technology overview provides a high-level summary of technologies being investigated, developed, and deployed by WRPS to advance Hanford Site tank waste retrieval and processing. Transformational technologies are needed to complete Hanford tank waste retrieval and treatment by 12/31/2047. Hanford's underground waste storage tanks hold approximately 57 million gallons of radiochemical waste from nuclear defense production - more tank waste than any other site in the United States. In addition, the waste is uniquely complicated because it contains constituents from at least six major radiochemical processes and several lesser processes. It is intermixed and complexed more than any other waste collection known to exist in the world. The multi-faceted nature of Hanford's tank waste means that legally binding agreements in the Federal Facility Agreement and Consent Order (known as the Tri-Party Agreement) and between the Department of Energy (DOE) and its contractors may not be met using current vitrification schedules, plans, and methods. WRPS and the DOE are developing, testing, and deploying technologies to meet the necessary commitments and complete the DOE's River Protection Project (RPP) mission within environmentally acceptable requirements. Technology solutions are outlined, along with processes and priorities for selecting and developing them. DOE's Office of Environmental Management (EM) identifies the environmental management technology needs and the activities necessary to address them. The U.S. Congress then funds these activities through EM or the DOE field offices. Finally, an array of entities that include DOE site prime contractors and

  15. Physiotherapists use a great variety of motor learning options in neurological rehabilitation, from which they choose through an iterative process: a retrospective think-aloud study.

    Science.gov (United States)

    Kleynen, Melanie; Moser, Albine; Haarsma, Frederike A; Beurskens, Anna J; Braun, Susy M

    2017-08-01

    The goal of this study was to examine which motor learning options are applied by experienced physiotherapists in neurological rehabilitation, and how they choose between the different options. A descriptive qualitative approach was used. A purposive sample of five expert physiotherapists from the neurological ward of a rehabilitation center participated. Data were collected using nine videotaped therapy situations. During retrospective think-aloud interviews, the physiotherapists were instructed to constantly "think aloud" while they were watching their own videos. Five "operators" were identified: "act", "know", "observe", "assess" and "argue". The "act" operator consisted of 34 motor learning options, which were clustered into "instruction", "feedback" and "organization". The "know", "observe", "assess" and "argue" operators explained how therapists chose one of these options. The four operators seem to be interrelated and together lead to a decision to apply a particular motor learning option. Results show that the participating physiotherapists used a great variety of motor learning options in their treatment sessions. Further, the decision-making process with regard to these motor learning options was identified. Results may support future intervention studies that match the content and process of therapy in daily practice. The study should be repeated with other physiotherapists. Implications for Rehabilitation The study provided insight into the way experienced therapist handle the great variety of possible motor learning options, including concrete ideas on how to operationalize these options in specific situations. Despite differences in patients' abilities, it seems that therapists use the same underlying clinical reasoning process when choosing a particular motor learning option. Participating physiotherapists used more than the in guidelines suggested motor learning options and considered more than the suggested factors, hence adding practice based

  16. Electrostatic coating technologies for food processing.

    Science.gov (United States)

    Barringer, Sheryl A; Sumonsiri, Nutsuda

    2015-01-01

    The application of electrostatics in both powder and liquid coating can improve the quality of food, such as its appearance, aroma, taste, and shelf life. Coatings can be found most commonly in the snack food industry, as well as in confectionery, bakery, meat and cheese processing. In electrostatic powder coating, the most important factors influencing coating quality are powder particle size, density, flowability, charge, and resistivity, as well as the surface properties and characteristics of the target. The most important factors during electrostatic liquid coating, also known as electrohydrodynamic coating, include applied voltage and electrical resistivity and viscosity of the liquid. A good understanding of these factors is needed for the design of optimal coating systems for food processing.

  17. Innovative Pedagogical Processes Involving Educational Technology

    DEFF Research Database (Denmark)

    Weitze, Charlotte Lærke

    This design-based research project investigates the elements, methods, processes and practices that can contribute to the creation of reflected, innovative and motivating learning designs for teachers and students in a hybrid synchronous video-mediated teaching context, with a focus on how...... about how design and learning processes can support continuous pedagogical innovation and competence development. The objective of the learning designs was to create motivating learning experiences for the students in the hybrid synchronous video-mediated learning environment, to which end...... it experimented with gamified learning designs. This involved the students designing digital games while implementing learning goals from their curriculum. The project thus created knowledge about which learning designs and competence development models were possible in this environment, which learning designs...

  18. Hydrometallurgical Processing Technology of Titanomagnetite Ores

    Directory of Open Access Journals (Sweden)

    Victor Ivanovich Sachkov

    2017-12-01

    Full Text Available In this paper, we study the possibility of obtaining iron and titanium-vanadium concentrates with highest contents of iron and titanium, respectively, through hydrometallurgical processing of the titanomagnetite ores of the Chineisk deposit. We varied two key parameters to determine the efficiency of the process: (a concentration of leaching solution (ammonium fluoride; and (b acidity of solution. Ammonium fluoride concentration was varied from 0.08 mol/L to 4.2 mol/L with the other fixed parameters. It was shown that optimum ammonium fluoride concentration for leaching the ore is 0.42 mol/L; at these concentrations iron and titanium contents are about 62.8 wt % and 3.5 wt % in solid phase, respectively. The acidity of solution was changed by adding of hydrofluoric acid with varied concentration (from 0.86 mol/L to 4.07 mol/L to ammonium fluoride solution with fixed concentration of 0.42 mol/L. The best results (degree of titanium extraction = 63.7% were obtained when using a solution of hydrofluoric acid with concentration 4.07 mol/L. In this case, the addition of acid makes it possible to increase the Fe/Ti ratio by 3.4 times in comparison with the original ore. Thus, we conclude that acidity and the concentration of ammonium fluoride solution significantly influences the selectivity of the hydrometallurgical process.

  19. Agricultural land management options after the Chernobyl and Fukushima accidents: The articulation of science, technology, and society.

    Science.gov (United States)

    Vandenhove, Hildegarde; Turcanu, Catrinel

    2016-10-01

    The options adopted for recovery of agricultural land after the Chernobyl and Fukushima accidents are compared by examining their technical and socio-economic aspects. The analysis highlights commonalities such as the implementation of tillage and other types of countermeasures and differences in approach, such as preferences for topsoil removal in Fukushima and the application of K fertilizers in Chernobyl. This analysis shows that the recovery approach needs to be context-specific to best suit the physical, social, and political environment. The complex nature of the decision problem calls for a formal process for engaging stakeholders and the development of adequate decision support tools. Integr Environ Assess Manag 2016;12:662-666. © 2016 SETAC. © 2016 SETAC.

  20. Evaluation of options for energy recovery from municipal solid waste in India using the hierarchical analytical network process

    International Nuclear Information System (INIS)

    Nixon, J.D.; Dey, P.K.; Ghosh, S.K.; Davies, P.A.

    2013-01-01

    In this paper a Hierarchical Analytical Network Process (HANP) model is demonstrated for evaluating alternative technologies for generating electricity from MSW in India. The technological alternatives and evaluation criteria for the HANP study are characterised by reviewing the literature and consulting experts in the field of waste management. Technologies reviewed in the context of India include landfill, anaerobic digestion, incineration, pelletisation and gasification. To investigate the sensitivity of the result, we examine variations in expert opinions and carry out an Analytical Hierarchy Process (AHP) analysis for comparison. We find that anaerobic digestion is the preferred technology for generating electricity from MSW in India. Gasification is indicated as the preferred technology in an AHP model due to the exclusion of criteria dependencies and in an HANP analysis when placing a high priority on net output and retention time. We conclude that HANP successfully provides a structured framework for recommending which technologies to pursue in India, and the adoption of such tools is critical at a time when key investments in infrastructure are being made. Therefore the presented methodology is thought to have a wider potential for investors, policy makers, researchers and plant developers in India and elsewhere. - Highlights: • We evaluate alternative technologies for generating electricity from waste. • The methodology we develop is based on the analytical network process. • Assessment is made against technical, financial, environmental and risk criteria. • Anaerobic digestion and gasification are the preferred technologies for India. • The method reduces risk and ensures sustainability in energy project planning

  1. Technology Estimating: A Process to Determine the Cost and Schedule of Space Technology Research and Development

    Science.gov (United States)

    Cole, Stuart K.; Reeves, John D.; Williams-Byrd, Julie A.; Greenberg, Marc; Comstock, Doug; Olds, John R.; Wallace, Jon; DePasquale, Dominic; Schaffer, Mark

    2013-01-01

    NASA is investing in new technologies that include 14 primary technology roadmap areas, and aeronautics. Understanding the cost for research and development of these technologies and the time it takes to increase the maturity of the technology is important to the support of the ongoing and future NASA missions. Overall, technology estimating may help provide guidance to technology investment strategies to help improve evaluation of technology affordability, and aid in decision support. The research provides a summary of the framework development of a Technology Estimating process where four technology roadmap areas were selected to be studied. The framework includes definition of terms, discussion for narrowing the focus from 14 NASA Technology Roadmap areas to four, and further refinement to include technologies, TRL range of 2 to 6. Included in this paper is a discussion to address the evaluation of 20 unique technology parameters that were initially identified, evaluated and then subsequently reduced for use in characterizing these technologies. A discussion of data acquisition effort and criteria established for data quality are provided. The findings obtained during the research included gaps identified, and a description of a spreadsheet-based estimating tool initiated as a part of the Technology Estimating process.

  2. Performance Analyses in an Assistive Technology Service Delivery Process

    DEFF Research Database (Denmark)

    Petersen, Anne Karin

    Performance Analyses in an Assistive Technology Service Delivery Process.Keywords: process model, occupational performance, assistive technologiesThe Poster is about teaching students, using models and theory in education and practice. It is related to Occupational therapy process and professional...... af top-til-bund, klientcentreret og aktivitetsbaseret interventioner, ERGO/MunksgaardFisher, A. &, Griswold, L. A., 2014. Performance Skills. I: B.Schell red.2014 Occupational Therapy. Willard &Spackman’s occupational therapy. -12th ed., p.249-264Cook A.M., Polgar J.M. (2015) Assistive Technologies...

  3. Application of image processing technology in yarn hairiness detection

    Directory of Open Access Journals (Sweden)

    Guohong ZHANG

    2016-02-01

    Full Text Available Digital image processing technology is one of the new methods for yarn detection, which can realize the digital characterization and objective evaluation of yarn appearance. This paper overviews the current status of development and application of digital image processing technology used for yarn hairiness evaluation, and analyzes and compares the traditional detection methods and this new developed method. Compared with the traditional methods, the image processing technology based method is more objective, fast and accurate, which is the vital development trend of the yarn appearance evaluation.

  4. [Mechanized system for planning technological processes].

    Science.gov (United States)

    Pashchenko, V S; Shapiro, A M

    1977-01-01

    A mechanized system for the production processes planning involving the use of an electronic code device for data preparation on a punched tape of the "EPECT-IT" type, at the base of which there are classifiers of standard operations and transitions to individual design members, is considered. A fragment of the classifier and a skeleton diagram of the system are presented. It is pointed out that the use of the system helps improve the quality of the design work, as well as to yield considerable economic advantages. The system is in operation at some enterprises of the medical engineering industry.

  5. Analysis of radwaste material management options for experimental DUPIC fuel fabrication process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. H.; Park, J. J.; Yang, M. S.; Kim, K. H.; Shin, J. M.; Lee, H. S.; Ko, W. I.; Lee, J. W.; Yim, S. P.; Hong, D. H.; Lee, J. Y.; Baik, S. Y.; Song, W. S.; Yoo, B. O.; Lee, E. P.; Kang, I. S. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-03-01

    This report is desirable to review management options in advance for radioactive waste generated from manufacturing experiment of DUPIC nuclear fuel as well as residual nuclear material and dismantled equipment. This report was written for helping researchers working in related facilities to DUPIC project understanding management of DUPIC radioactive waste as well as fellows in DUPIC project. Also, it will be used as basic material to prove transparency and safeguardability of DUPIC fuel cycle. In order to meet these purposes, this report includes basic experiment plan for manufacturing DUPIC nuclear fuel, outlines for DUPIC manufacturing facility and equipment, arising source and estimated amount of radioactive waste, waste classification and packing, transport cask, transport procedures. 15 refs., 31 figs., 11 tabs. (Author)

  6. [Study on baking processing technology of hui medicine Aconitum flavum].

    Science.gov (United States)

    Fu, Xue-yan; Zhang, Bai-tong; Li, Ting-ting; Dong, Lin; Hao, Wen-jing; Yu, Liang

    2013-12-01

    To screen and optimize the processing technology of Aconitum flavum. The acute-toxicity, anti-inflammatory and analgesic experiments were used as indexes. Four processing methods, including decoction, streaming, baking and processing with Chebulae Fructus decoction, were compared to screen the optimum processing method for Aconitum flavum. The baking time was also optimized. The optimal baked technology was that 1-2 mm decoction pieces was baked at 105 degrees C for 3 hours. The baking method is proved to be the optimal processing method of Aconitum flavum. It is shown that this method is simple and stable.

  7. Status and prospect of radiation processing technology in Malaysia

    International Nuclear Information System (INIS)

    Khairul Zaman Hj Mohd Dahlan; Nahrul Khair Alang Md Rashid

    2001-01-01

    Radiation processing technology in Malaysia is gaining acceptance by the local industry. The technology has proven to enhance the industrial efficiency, productivity and improve product quality and competitiveness. For many years, variety of radiation crosslinkable materials based on synthetic polymers have been produced either in the form of thermoplastic resins, polymer blends or composites. Today, effort is being focused towards producing environmentally friendly and biodegradable materials using natural polymers. The government of Malaysia through the Malaysian Institute for Nuclear Technology Research (MINT) has developed research program to utilize indigenous materials such as natural rubber, palm oil and polysaccharide. Radiation processing technology is used to process (crosslink/grafting/curing) the materials at a competitive cost. This technology can be applied in several industrial sectors such as automobile, aerospace, construction and healthcare. (author)

  8. Status and prospect of radiation processing technology in Malaysia

    Energy Technology Data Exchange (ETDEWEB)

    Khairul Zaman Hj. Mohd Dahlan; Nahrul Khair Alang Md Rashid [Malaysian Institute for Nuclear Technology Research (MINT), Bangi, Selangor Darul Ehsan (Malaysia)

    2001-03-01

    Radiation processing technology in Malaysia is gaining acceptance by the local industry. The technology has proven to enhance the industrial efficiency, productivity and improve product quality and competitiveness. For many years, variety of radiation crosslinkable materials based on synthetic polymers have been produced either in the form of thermoplastic resins, polymer blends or composites. Today, effort is being focused towards producing environmentally friendly and biodegradable materials using natural polymers. The government of Malaysia through the Malaysian Institute for Nuclear Technology Research (MINT) has developed research program to utilize indigenous materials such as natural rubber, palm oil and polysaccharide. Radiation processing technology is used to process (crosslink/grafting/curing) the materials at a competitive cost. This technology can be applied in several industrial sectors such as automobile, aerospace, construction and healthcare. (author)

  9. Dry process fuel performance technology development

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Kweon Ho; Kim, K. W.; Kim, B. K. (and others)

    2006-06-15

    The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

  10. Dry process fuel performance technology development

    International Nuclear Information System (INIS)

    Kang, Kweon Ho; Kim, K. W.; Kim, B. K.

    2006-06-01

    The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

  11. Efficiency of Traditional Food Processing Technology in the Locality ...

    African Journals Online (AJOL)

    This paper identified the efficiency of traditional food processing technology which is the set of methods and techniques used for transforming raw food ingredients into food or other forms for consumption by human or animals either in the home or by the food processing industry. Food processing has also helped to create ...

  12. Analysis of the economic impact of different Chinese climate policy options based on a CGE model incorporating endogenous technological change

    International Nuclear Information System (INIS)

    Wang Ke; Wang Can; Chen Jining

    2009-01-01

    Abatement cost is the main concern for climate change mitigation and the key factor for mitigation cost is technological change. This study established an integrated economic, energy, environmental, dynamic, computable general equilibrium (CGE) model representing endogenous technological change for China's climate change policy analysis. This study analyzed and compared the economic impact of different approaches to mitigation commitments as well as the potential role of technological change in the formulation of mitigation targets and commitments, taking into account China's climate policy-making needs based on the current international climate negotiation process. The results show that, absolute emission limits similar to the Kyoto Protocol will seriously impede the future economic development of China, while the impact of an 80% reduction in carbon intensity, forecast for 2050 based on the 2005 level, is relatively small. Technological change can promote economic growth, improve energy efficiency and reduce carbon intensity per unit of output through the substitution of production factors. Consequently it can reduce marginal abatement cost and related GDP loss by mitigation. At the same time it can increase mitigation potentials and extend the emission reduction amount, showing that consideration of the impact of technological change when deciding the emission reduction targets is necessary.

  13. A Process for Technology Prioritization in a Competitive Environment

    Science.gov (United States)

    Stephens, Karen; Herman, Melody; Griffin, Brand

    2006-01-01

    This slide presentation reviews NASA's process for prioritizing technology requirements where there is a competitive environment. The In-Space Propulsion Technology (ISPT) project is used to exemplify the process. The ISPT project focuses on the mid level Technology Readiness Level (TRL) for development. These are TRL's 4 through 6, (i.e. Technology Development and Technology Demonstration. The objective of the planning activity is to identify the current most likely date each technology is needed and create ISPT technology development schedules based on these dates. There is a minimum of 4 years between flight and pacing mission. The ISPT Project needed to identify the "pacing mission" for each technology in order to provide funding for each area. Graphic representations show the development of the process. A matrix shows which missions are currently receiving pull from the both the Solar System Exploration and the Sun-Solar System Connection Roadmaps. The timeframes of the pacing missions technologies are shown for various types of propulsion. A pacing mission that was in the near future serves to increase the priority for funding. Adaptations were made when budget reductions precluded the total implementation of the plan.

  14. Information Technologies and Globalization: New Perspectives of Teaching Learning Process

    Science.gov (United States)

    Hussain, Irshad

    2008-01-01

    This article discusses how information technologies and globalization have opened new avenues and horizons for educators and learners. It discusses different experiences of using information and communication technologies (ICTs) in teaching learning process the world over in the age of globalization. It focuses on the ways these new trends have…

  15. Research on Implementing Big Data: Technology, People, & Processes

    Science.gov (United States)

    Rankin, Jenny Grant; Johnson, Margie; Dennis, Randall

    2015-01-01

    When many people hear the term "big data", they primarily think of a technology tool for the collection and reporting of data of high variety, volume, and velocity. However, the complexity of big data is not only the technology, but the supporting processes, policies, and people supporting it. This paper was written by three experts to…

  16. SpaceCube Technology Brief Hybrid Data Processing System

    Science.gov (United States)

    Petrick, Dave

    2016-01-01

    The intent of this presentation is to give status to multiple audience types on the SpaceCube data processing technology at GSFC. SpaceCube has grown to support multiple missions inside and outside of NASA, and we are being requested to give technology overviews in various forums.

  17. Transformation towards a Renewable Energy System in Brazil and Mexico—Technological and Structural Options for Latin America

    Directory of Open Access Journals (Sweden)

    Sonja Simon

    2018-04-01

    Full Text Available Newly industrialized countries face major challenges to comply with the Paris Treaty targets as economic growth and prosperity lead to increasing energy demand. Our paper analyses technological and structural options in terms of energy efficiency and renewable energies for a massive reduction of energy-related CO2 emissions in Latin America. Brazil and Mexico share similar growth prospects but differ significantly with respect to renewable energy potentials. We identify, how this leads to different transformation pathways. By applying an energy system balancing model we develop normative energy system transformation scenarios across the heating, power, and mobility sectors, including their potential interactions. The normative scenarios rely on three basic strategies for both countries: (1 strong exploitation of efficiency potentials; (2 tapping the renewable energy potentials; and (3 sector coupling and electrification of heat supply and transport. Despite economic growth, significant CO2 emission reductions could be achieved in Brazil from 440 Gt/a (2.2 t/cap in 2012 to 0.4 Gt (2 kg/cap in 2050 and in Mexico from 400 Gt/a (3.3 t/cap to 80 Gt (0.5 t/cap. Our study shows the gap between existing policy and scenarios and our strategies, which provide an economically feasible way to comply with the Paris treaty targets.

  18. Business modeling process for university’s technology transfer offices

    Directory of Open Access Journals (Sweden)

    Marin Alexandru

    2017-07-01

    Full Text Available The present paper is devoted to analyze the appropriate recommendations to increase the effectiveness of technology transfer centers from Romanian National Network for Innovation and Technology Transfer - ReNITT, hosted by universities. The study is focused on the definition of a conceptual frame to develop specific business models, by the specialized compartments from technology/knowledge transfer entities, and using the specific instruments of business modeling process. The qualitative and quantitative analysis of the 8 steps scheduling of pairing the building blocks of the Business Models Canvas, corresponding to the specific technology transfer models, and taking into account the elements of the value chain of technology transfer and making connections with technology readiness level, allows a clarification of this relative “fuzzy” and complicated modeling process of university’s Technology Transfer Offices activities, gathering in a concentrated format all necessary information. According to their mission, objectives and strategies, universities decide upon a certain business model for the Technology Transfer Offices, adaptable to client segment and value proposition to attain, by the offered services portfolio. In conclusion, during their activities, Technology Transfer Offices identify, validate and exploit the opportunities originated from applicative research results, by “technology push” methods. Also, there are necessary specific competences (human and material to develop externally aware business models starting from real needs of the clients, by “market pull” techniques, that would contribute to enhance the endogenous innovation potential of firms.

  19. Information Technology in Small Medium Enterprise: Logistic and Production Processes

    Directory of Open Access Journals (Sweden)

    Maurizio Pighin

    2017-01-01

    Full Text Available This paper presents and discuss a survey which describes how small-medium enterprises (SMEs implement and use their information system with respect to their logistic and production processes. The study first describes the rationale of the research, then it identifies the characteristics of the companies and detects their general attitude towards information technology (IT. In the following section the paper presents a set of detailed processes to verify the structure and workflow of companies and how IT supports their processes. In the last part we study the influence of some company characteristics to effective use of processes and to different technological approaches, to support defined logistic and production processes. The novelty of the study and its interest, both in academic and institutional context as in the real world, resides in the opportunity to verify and understand the different attitudes of SMEs towards information technology in defining, organizing, planning and control their processes.

  20. Innovation in Construction: Learning Processes in implementing new Technologies

    DEFF Research Database (Denmark)

    Clausen, Lennie

    1999-01-01

    The article is concerned with the question: How do construction firms implement new technology on construction projects? A model of the implementation process is presented based on a review of the construction innovation literature, innovation theory, and organisational learning theories....

  1. Magsonic™ Carbothermal Technology Compared with the Electrolytic and Pidgeon Processes

    Science.gov (United States)

    Prentice, Leon H.; Haque, Nawshad

    A broad technology comparison of carbothermal magnesium production with present technologies has not been previously presented. In this paper a comparative analysis of CSIRO's MagSonic™ process is made with the electrolytic and Pidgeon processes. The comparison covers energy intensity (GJ/tonne Mg), labor intensity (person-hours/tonne Mg), capital intensity (USD/tonne annual Mg installed capacity), and Global Warming Potential (GWP, tonnes CO2-equivalent/tonne Mg). Carbothermal technology is advantageous on all measures except capital intensity (where it is roughly twice the capital cost of a similarly-sized Pidgeon plant). Carbothermal and electrolytic production can have comparatively low environmental impacts, with typical emissions one-sixth those of the Pidgeon process. Despite recent progress, the Pidgeon process depends upon abundant energy and labor combined with few environmental constraints. Pressure is expected to increase on environmental constraints and labor and energy costs over the coming decade. Carbothermal reduction technology appears to be competitive for future production.

  2. TECHNOLOGICAL PROCESSES OF PRODUCTION OF THE MASS FUNCTION CAST BARS

    Directory of Open Access Journals (Sweden)

    A. N. Krutilin

    2012-01-01

    Full Text Available A number of scientifically grounded technical decisions, the whole set of which has enabled to create technological processes of production of high-quality cast bars of mass appointment is offered.

  3. Thermal food processing: new technologies and quality issues

    National Research Council Canada - National Science Library

    Sun, Da-Wen

    2012-01-01

    .... The editor of Thermal Food Processing: New Technologies and Quality Issues presents a comprehensive reference through authors that assist in meeting this challenge by explaining the latest developments and analyzing the latest trends...

  4. The Black-Scholes option pricing problem in mathematical finance: generalization and extensions for a large class of stochastic processes

    Science.gov (United States)

    Bouchaud, Jean-Philippe; Sornette, Didier

    1994-06-01

    The ability to price risks and devise optimal investment strategies in thé présence of an uncertain "random" market is thé cornerstone of modern finance theory. We first consider thé simplest such problem of a so-called "European call option" initially solved by Black and Scholes using Ito stochastic calculus for markets modelled by a log-Brownien stochastic process. A simple and powerful formalism is presented which allows us to generalize thé analysis to a large class of stochastic processes, such as ARCH, jump or Lévy processes. We also address thé case of correlated Gaussian processes, which is shown to be a good description of three différent market indices (MATIF, CAC40, FTSE100). Our main result is thé introduction of thé concept of an optimal strategy in the sense of (functional) minimization of the risk with respect to the portfolio. If the risk may be made to vanish for particular continuous uncorrelated 'quasiGaussian' stochastic processes (including Black and Scholes model), this is no longer the case for more general stochastic processes. The value of the residual risk is obtained and suggests the concept of risk-corrected option prices. In the presence of very large deviations such as in Lévy processes, new criteria for rational fixing of the option prices are discussed. We also apply our method to other types of options, `Asian', `American', and discuss new possibilities (`doubledecker'...). The inclusion of transaction costs leads to the appearance of a natural characteristic trading time scale. L'aptitude à quantifier le coût du risque et à définir une stratégie optimale de gestion de portefeuille dans un marché aléatoire constitue la base de la théorie moderne de la finance. Nous considérons d'abord le problème le plus simple de ce type, à savoir celui de l'option d'achat `européenne', qui a été résolu par Black et Scholes à l'aide du calcul stochastique d'Ito appliqué aux marchés modélisés par un processus Log

  5. Law, science and technology. The nuclear option, ethics and law; Droit, Science et Technologie. L`option nucleaire, l`ethique et le droit

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    Technological innovations in the field of nuclear energy, as well as the diversity of applications using ionizing radiations contribute to the necessity of implementation of legislation and laws. This conference will give some ideas on political, ethical and legal aspects as far as nuclear energy development is concerned. Separate abstract were prepared for all the papers in this volume. (TEC).

  6. Efficient pricing of Asian options under Lévy processes based on Fourier cosine expansions Part I : European-style products

    NARCIS (Netherlands)

    Zhang, B.; Oosterlee, C.W.

    2011-01-01

    We propose an efficient pricing method for arithmetic, and geometric, Asian options under Levy processes, based on Fourier cosine expansions and Clenshaw–Curtis quadrature. The pricing method is developed for both European–style and American–style Asian options, and for discretely and continuously

  7. Thermo-Economic Modelling and Process Integration of CO2-Mitigation Options on Oil and Gas Platforms

    DEFF Research Database (Denmark)

    Nguyen, Tuong-Van; Tock, Laurence; Breuhaus, Peter

    2014-01-01

    The offshore extraction of oil and gas is an energy-intensive process associated with large CO2 and CH4 emissions to the atmosphere and chemicals to the sea. The taxation of these emissions has encouraged the development of more energy-efficient and environmental-friendly solutions, of which three...... recovering CO2 that can be used for enhanced oil recovery. In this paper, a North Sea platform is considered as case study, and the site-scale retrofit integration of these three options is analysed, considering thermodynamic, economic and environmental performance indicators. The results illustrate...

  8. Radiation processing technology in the 21st century

    International Nuclear Information System (INIS)

    Miyuki Hagiwara

    1997-01-01

    The address discusses the following issue - towards the 21st century, we are required more and more to create innovative technologies to solve problems about environment, energy, natural resources, materials, health care, food and others which are the great concern to human beings. For the radiation processing technology to survive, it will be required to provide answers to those problems. The use of radiation of polymer modification will remain as an important field of the radiation application. Some other promising polymer processing can be cited as those which will grow in near future; for environment technology - polymeric fibers grafted with ion exchange residues to remove toxic metals for cleaning industrial waste water; For health care technology - crosslinked polyvinylalcohol hydrogel for wound dressing (irradiation of hydrogel); For high performance materials technology - less toxic crosslinked natural rubber latex (irradiation of emulsion), abrasion resistant crosslinked PTFE (irradiation at high temperature)

  9. Reactor and process design in sustainable energy technology

    CERN Document Server

    Shi, Fan

    2014-01-01

    Reactor Process Design in Sustainable Energy Technology compiles and explains current developments in reactor and process design in sustainable energy technologies, including optimization and scale-up methodologies and numerical methods. Sustainable energy technologies that require more efficient means of converting and utilizing energy can help provide for burgeoning global energy demand while reducing anthropogenic carbon dioxide emissions associated with energy production. The book, contributed by an international team of academic and industry experts in the field, brings numerous reactor design cases to readers based on their valuable experience from lab R&D scale to industry levels. It is the first to emphasize reactor engineering in sustainable energy technology discussing design. It provides comprehensive tools and information to help engineers and energy professionals learn, design, and specify chemical reactors and processes confidently. Emphasis on reactor engineering in sustainable energy techn...

  10. Advanced Process Technology: Combi Materials Science and Atmospheric Processing (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2011-06-01

    Capabilities fact sheet for the National Center for Photovoltaics: Process Technology and Advanced Concepts -- High-Throughput Combi Material Science and Atmospheric Processing that includes scope, core competencies and capabilities, and contact/web information.

  11. Numerical analysis of additive, Lévy and Feller processes with applications to option pricing

    OpenAIRE

    Schwab, Christoph; Reichmann, Oleg

    2010-01-01

    We review the design and analysis of multiresolution (wavelet) methods for the numerical solution of the Kolmogoroff equations arising, among others, in financial engineering when Lévy and Feller or Additive processes are used to model the dynamics of the risky assets. In particular, the Dirichlet and free boundary problems connected to barrier and American style contracts are specified and solution algorithms based on wavelet representations of the Feller Processes' Dirichlet Forms are prese...

  12. Future nuclear systems, Astrid, an option for the fourth generation: preparing the future of nuclear energy, sustainably optimising resources, defining technological options, sodium-cooled fast reactor

    International Nuclear Information System (INIS)

    Ter Minassian, Vahe

    2016-01-01

    Energy independence and security of supplies, improved safety standards, sustainably optimised material management, minimal waste production - all without greenhouse gas emissions. These are the Generation IV International Forum specifications for nuclear energy of the future. The CEA is responsible for designing Astrid, an integrated technology demonstrator for the 4. generation of sodium-cooled fast reactors, in accordance with the French Sustainable Nuclear Materials and Waste Management Act of June 28, 2006, and funded as part of the Investments for the Future programme enacted by the French parliament in 2010. Energy management - a vital need and a factor of economic growth - is a major challenge for the world of tomorrow. The nuclear industry has significant advantages in this regard, although it faces safety, resource sustainability, and waste management issues that must be met through continuing technological innovation. Fast reactors are also of interest to the nuclear industry because their recycling capability would solve a number of problems related to the stockpiles of uranium and plutonium. After the resumption of R and D work with EDF and AREVA in 2006, the Astrid design studies began in 2010. The CEA, as owner and contracting authority for this programme, is now in a position to define the broad outlines of the demonstrator 4. generation reactor that could be commissioned during the next decade. A sodium-cooled fast reactor (SFR) operates in the same way as a conventional nuclear reactor: fission reactions in the atoms of fuel in the core generate heat, which is conveyed to a turbine generator to produce electricity. In the context of 4. generation technology, SFRs represent an innovative solution for optimising the use of raw materials as well as for enhancing safety. Here are a few ideas advanced by the CEA. (authors)

  13. Stakeholder and Process Alignment in Navy Installation Technology Transitions

    Science.gov (United States)

    2017-02-01

    report : We have numerous technical success stories that are not fully integrated because of certain circumstances or conditions— some of which are totally...simultaneously integrate tech- nologies with existing systems, secure stakeholder support and integrate with shore planning and funding, program and...process requirements, the ARLs measure progress across three domains: technology integration , stakeholders and processes. Hurdles in any one of

  14. Distributed automatic control of technological processes in conditions of weightlessness

    Science.gov (United States)

    Kukhtenko, A. I.; Merkulov, V. I.; Samoylenko, Y. I.; Ladikov-Royev, Y. P.

    1986-01-01

    Some problems associated with the automatic control of liquid metal and plasma systems under conditions of weightlessness are examined, with particular reference to the problem of stability of liquid equilibrium configurations. The theoretical fundamentals of automatic control of processes in electrically conducting continuous media are outlined, and means of using electromagnetic fields for simulating technological processes in a space environment are discussed.

  15. STUDENTS READINESS TO USE INFORMATION TECHNOLOGY IN UNIVERSITIES EDUCATIONAL PROCESS

    Directory of Open Access Journals (Sweden)

    V. Denysenko

    2015-03-01

    Full Text Available The article analyzes the problem of readiness of students of different specialties to use information technology in the educational process of higher education. Particular attention is paid to contemporary processes of globalization and informatization of higher education as a priority trends of modern Ukrainian society. Experimental data provided in the publication are comparative characteristics of the students using different specialty areas and preparation of information technologies in education. Computerization of the educational process - one of the main priorities in the development of higher education, a new stage for the entire higher education system, promising improvements in the direction of learning in higher education

  16. Application of information and communication technology in process reengineering

    Directory of Open Access Journals (Sweden)

    Đurović Aleksandar M.

    2014-01-01

    Full Text Available This paper examines the role of information communication technologies in reengineering processes. General analysis of a process will show that information communication technologies improve their efficiency. Reengineering model based on the BPMN 2.0 standard will be applied to the process of seeking internship/job by students from Faculty of Transport and Traffic Engineering. In the paper, after defining the technical characteristics and required functionalities, web / mobile application is proposed, enabling better visibility of traffic engineers to companies seeking that education profile.

  17. [Technology development as social process: prospects and frontiers of social scientific elucidation of technological advancement].

    Science.gov (United States)

    Dierkes, M

    1990-05-01

    This article provides an overview of the new developments in social scientific technology research which have changed considerably as a result of public debate and reactions to the importance of advancements in technology. The shift in emphasis, away from the effects of technology to its shaping, is described and certain hypotheses and concepts of advancement in the study of the social conditions underlying technical development processes are presented.

  18. The Process Genre Writing Approach; An Alternative Option for the Modern Classroom

    Science.gov (United States)

    Tudor, Emma

    2017-01-01

    "Writing involves knowledge about the language, the context in which writing happens and skills in using language. Writing development happens by drawing out the learners' potential and providing input to which learners respond" (Badger & White, 2000.) Taking this in to account, the Process Genre Approach in writing classes can be…

  19. Mobile Technology and CAD Technology Integration in Teaching Architectural Design Process for Producing Creative Product

    Science.gov (United States)

    Bin Hassan, Isham Shah; Ismail, Mohd Arif; Mustafa, Ramlee

    2011-01-01

    The purpose of this research is to examine the effect of integrating the mobile and CAD technology on teaching architectural design process for Malaysian polytechnic architectural students in producing a creative product. The website is set up based on Caroll's minimal theory, while mobile and CAD technology integration is based on Brown and…

  20. Spent fuel reprocessing options

    International Nuclear Information System (INIS)

    2008-08-01

    The objective of this publication is to provide an update on the latest developments in nuclear reprocessing technologies in the light of new developments on the global nuclear scene. The background information on spent fuel reprocessing is provided in Section One. Substantial global growth of nuclear electricity generation is expected to occur during this century, in response to environmental issues and to assure the sustainability of the electrical energy supply in both industrial and less-developed countries. This growth carries with it an increasing responsibility to ensure that nuclear fuel cycle technologies are used only for peaceful purposes. In Section Two, an overview of the options for spent fuel reprocessing and their level of development are provided. A number of options exist for the treatment of spent fuel. Some, including those that avoid separation of a pure plutonium stream, are at an advanced level of technological maturity. These could be deployed in the next generation of industrial-scale reprocessing plants, while others (such as dry methods) are at a pilot scale, laboratory scale or conceptual stage of development. In Section Three, research and development in support of advanced reprocessing options is described. Next-generation spent fuel reprocessing plants are likely to be based on aqueous extraction processes that can be designed to a country specific set of spent fuel partitioning criteria for recycling of fissile materials to advanced light water reactors or fast spectrum reactors. The physical design of these plants must incorporate effective means for materials accountancy, safeguards and physical protection. Section four deals with issues and challenges related to spent fuel reprocessing. The spent fuel reprocessing options assessment of economics, proliferation resistance, and environmental impact are discussed. The importance of public acceptance for a reprocessing strategy is discussed. A review of modelling tools to support the

  1. Technology Summary Advancing Tank Waste Retreival And Processing

    International Nuclear Information System (INIS)

    Sams, T.L.

    2010-01-01

    This technology overview provides a high-level summary of technologies being investigated and developed by Washington River Protection Solutions (WRPS) to advance Hanford Site tank waste retrieval and processing. Technology solutions are outlined, along with processes and priorities for selecting and developing them. Hanford's underground waste storage tanks hold approximately 57 million gallons of radiochemical waste from nuclear defense production - more tank waste than any other site in the United States. In addition, the waste is uniquely complicated since it contains constituents from at least six major radiochemical processes and several lesser processes. It is intermixed and complexed more than any other waste collection known to exist in the world. The multi-faceted nature of Hanford's tank waste means that legally binding agreements in the Federal Facility Agreement and Consent Order (known as the Tri-Party Agreement) and between the Department of Energy (DOE) and its contractors may not be met using current vitrification schedules, plans and methods. WRPS and the DOE are therefore developing, testing, and deploying technologies to ensure that they can meet the necessary commitments and complete the DOE's River Protection Project (RPP) mission within environmentally acceptable requirements. Technology solutions are outlined, along with processes and priorities for selecting and developing them.

  2. The Impact Of Optical Storage Technology On Image Processing Systems

    Science.gov (United States)

    Garges, Daniel T.; Durbin, Gerald T.

    1984-09-01

    The recent announcement of commercially available high density optical storage devices will have a profound impact on the information processing industry. Just as the initial introduction of random access storage created entirely new processing strategies, optical technology will allow dramatic changes in the storage, retrieval, and dissemination of engineering drawings and other pictorial or text-based documents. Storage Technology Corporation has assumed a leading role in this arena with the introduction of the 7600 Optical Storage Subsystem, and the formation of StorageTek Integrated Systems, a subsidiary chartered to incorporate this new technology into deliverable total systems. This paper explores the impact of optical storage technology from the perspective of a leading-edge manufacturer and integrator.

  3. Impact of process parameters and design options on heat leaks of straight cryogenic distribution lines

    CERN Document Server

    Duda, Pawel; Chorowski, Maciej Pawel; Polinski, J

    2017-01-01

    The Future Circular Collider (FCC) accelerator will require a helium distribution system that will exceed the presently exploited transfer lines by almost 1 order of magnitude. The helium transfer line will contain five process pipes protected against heat leaks by a common thermal shield. The design pressure of the FCC process pipe with supercritical helium will be equal to 5.0 MPa, significantly exceeding the 2.0 MPa value in the present, state-of–art transfer lines. The increase of the design pressure requires construction changes to be introduced to the support system, the vacuum barriers and the compensation bellows. This will influence heat flows to the helium. The paper analyses the impact of the increased design pressure on the heat flow. The paper also offers a discussion of the design modifications to the compensation system, including the replacement of stainless steel with Invar—aimed at mitigating the pressure increase.

  4. Impact of process parameters and design options on heat leaks of straight cryogenic distribution lines

    Directory of Open Access Journals (Sweden)

    P. Duda

    2017-03-01

    Full Text Available The Future Circular Collider (FCC accelerator will require a helium distribution system that will exceed the presently exploited transfer lines by almost 1 order of magnitude. The helium transfer line will contain five process pipes protected against heat leaks by a common thermal shield. The design pressure of the FCC process pipe with supercritical helium will be equal to 5.0 MPa, significantly exceeding the 2.0 MPa value in the present, state-of–art transfer lines. The increase of the design pressure requires construction changes to be introduced to the support system, the vacuum barriers and the compensation bellows. This will influence heat flows to the helium. The paper analyses the impact of the increased design pressure on the heat flow. The paper also offers a discussion of the design modifications to the compensation system, including the replacement of stainless steel with Invar®—aimed at mitigating the pressure increase.

  5. A strategic analysis of future growth options for an established process control company

    OpenAIRE

    Levesque, Sheila Lynne

    2007-01-01

    This project speaks to the prevailing business environment presently encountered at WESTCOAST Controls Ltd (WESTCOAST), a leading process control company in British Columbia, Canada. The scope of the project covers topics such as company overview, external industry analysis, and internal company analysis including strategic tools such as Porter's 5 Forces. The project concludes with a recommendation for the restructuring of the control systems & solutions division for improved performan...

  6. Comparison of thermal scattering processing options for S(α,β) cards in MCNP

    International Nuclear Information System (INIS)

    Čerba, Štefan; Damian, Jose Ignacio Marquez; Lüley, Jakub; Vrban, Branislav; Farkas, Gabriel; Nečas, Vladimír; Haščík, Jan

    2013-01-01

    Highlights: ► Determination of MCNP calculation bias for WWER-440. ► Specific scattering law S(α,β). ► Benchmark cases investigated. ► Three methods to process material cards for hydrogen bound in light water. - Abstract: The MCNP distributions include sets of pre-calculated thermal scattering libraries but these libraries are available for several temperature steps only. In order to achieve reliable results it is suitable to process the cross section libraries for the desired temperature. In general, there are three methods to process these thermal scattering libraries for the desired temperatures. This paper deals with the comparison of these three methods on the basis of several benchmarks and on the basis of a thermal transient experiment of a WWER-440 reactor. The choice is up to the MCNP user but unfortunately very few studies concerning the comparison have been published so far. Therefore conclusions and results presented in this paper may help the user to choose the most appropriate method for his calculation

  7. Hybrid microcircuit technology handbook materials, processes, design, testing and production

    CERN Document Server

    Licari, James J

    1998-01-01

    The Hybrid Microcircuit Technology Handbook integrates the many diverse technologies used in the design, fabrication, assembly, and testing of hybrid segments crucial to the success of producing reliable circuits in high yields. Among these are: resistor trimming, wire bonding, die attachment, cleaning, hermetic sealing, and moisture analysis. In addition to thin films, thick films, and assembly processes, important chapters on substrate selections, handling (including electrostatic discharge), failure analysis, and documentation are included. A comprehensive chapter of design guidelines will

  8. PROCESS CONTROL IN THE EDUCATION OF ORGANIC CHEMICAL TECHNOLOGY

    OpenAIRE

    Csontos, lstván; Department of Organic Chemical Technology, Budapest University of Technology and Economics; Marosi, György; Department of Organic Chemical Technology, Budapest University of Technology and Economics; Faigl, Ferenc; Department of Organic Chemical Technology, Budapest University of Technology and Economics

    2013-01-01

    Laboratory practices for demonstrating the importance of advanced process control methods in the organic chemical technologies have been elaborated. It required the development of a system tha tintegrates the advantages of a reaction calorimeter and a model system of industrial controlled reactors. The hardware and software configuration support the transfer of elaborated control programs of reactions from laboratory level to the industrial technology. General control algorithms of diazotizat...

  9. Cogeneration technology alternatives study. Volume 2: Industrial process characteristics

    Science.gov (United States)

    1980-01-01

    Information and data for 26 industrial processes are presented. The following information is given for each process: (1) a description of the process including the annual energy consumption and product production and plant capacity; (2) the energy requirements of the process for each unit of production and the detailed data concerning electrical energy requirements and also hot water, steam, and direct fired thermal requirements; (3) anticipated trends affecting energy requirements with new process or production technologies; and (4) representative plant data including capacity and projected requirements through the year 2000.

  10. Applying Trusted Network Technology To Process Control Systems

    Science.gov (United States)

    Okhravi, Hamed; Nicol, David

    Interconnections between process control networks and enterprise networks expose instrumentation and control systems and the critical infrastructure components they operate to a variety of cyber attacks. Several architectural standards and security best practices have been proposed for industrial control systems. However, they are based on older architectures and do not leverage the latest hardware and software technologies. This paper describes new technologies that can be applied to the design of next generation security architectures for industrial control systems. The technologies are discussed along with their security benefits and design trade-offs.

  11. Image processing technologies in nuclear power plant monitoring

    International Nuclear Information System (INIS)

    Kubo, Katsumi; Kanemoto, Shigeru; Shimada, Hideo.

    1995-01-01

    Various monitoring activities are carried out in nuclear power plants to ensure that the high reliability requirements of such plants are met. Inspection patrols by operators are important for detecting small anomalies in equipment. Vibration, temperature, and visual images are major forms of information used in equipment inspections. We are developing remote automatic inspection technologies comprising image sensing of equipment conditions and automatic recognition of the images. This paper shows examples of image processing technologies, such as equipment monitoring using three-dimensional graphic plant models and vibration/temperature image data, and intelligent image recognition technology for detecting steam leakage. (author)

  12. Increasing biomass utilisation in energy systems: A comparative study of CO2 reduction and cost for different bioenergy processing options

    International Nuclear Information System (INIS)

    Wahlund, Bertil; Yan Jinyue; Westermark, Mats

    2004-01-01

    Emissions of greenhouse gases, such as CO 2 , need to be greatly reduced to avoid the risk of a harmful climate change. One powerful way to mitigate emissions is to switch fuels from fossil fuels to renewable energy, such as biomass. In this paper, we systematically investigate several bioenergy processing options, quantify the reduction rate and calculate the specific cost of reduction. This paper addresses the issue of which option Sweden should concentrate on to achieve the largest CO 2 reduction at the lowest cost. The results show that the largest and most long-term sustainable CO 2 reduction would be achieved by refining the woody biomass to fuel pellets for coal substitution, which have been done in Sweden. Refining to motor fuels, such as methanol, DME and ethanol, gives only half of the reduction and furthermore at a higher specific cost. Biomass refining into pellets enables transportation over long distances and seasonal storage, which is crucial for further utilisation of the woody biomass potential

  13. A review on hydrothermal pre-treatment technologies and environmental profiles of algal biomass processing.

    Science.gov (United States)

    Patel, Bhavish; Guo, Miao; Izadpanah, Arash; Shah, Nilay; Hellgardt, Klaus

    2016-01-01

    The need for efficient and clean biomass conversion technologies has propelled Hydrothermal (HT) processing as a promising treatment option for biofuel production. This manuscript discussed its application for pre-treatment of microalgae biomass to solid (biochar), liquid (biocrude and biodiesel) and gaseous (hydrogen and methane) products via Hydrothermal Carbonisation (HTC), Hydrothermal Liquefaction (HTL) and Supercritical Water Gasification (SCWG) as well as the utility of HT water as an extraction medium and HT Hydrotreatment (HDT) of algal biocrude. In addition, the Solar Energy Retained in Fuel (SERF) using HT technologies is calculated and compared with benchmark biofuel. Lastly, the Life Cycle Assessment (LCA) discusses the limitation of the current state of art as well as introduction to new potential input categories to obtain a detailed environmental profile. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Supercritical fluid technologies for ceramic-processing applications

    International Nuclear Information System (INIS)

    Matson, D.W.; Smith, R.D.

    1989-01-01

    This paper reports on the applications of supercritical fluid technologies for ceramic processing. The physical and chemical properties of these densified gases are summarized and related to their use as solvents and processing media. Several areas are identified in which specific ceramic processes benefit from the unique properties of supercritical fluids. The rapid expansion of supercritical fluid solutions provides a technique for producing fine uniform powders and thin films of widely varying materials. Supercritical drying technologies allow the formation of highly porous aerogel products with potentially wide application. Hydrothermal processes leading to the formation of large single crystals and microcrystalline powders can also be extended into the supercritical regime of water. Additional applications and potential applications are identified in the areas of extraction of binders and other additives from ceramic compacts, densification of porous ceramics, the formation of powders in supercritical micro-emulsions, and in preceramic polymer processing

  15. Process Options Description for Vitrification Flowsheet Model of INEEL Sodium Bearing Waste

    International Nuclear Information System (INIS)

    Nichols, T.T.; Taylor, D.D.; Lauerhass, L.; Barnes, C.M.

    2002-01-01

    The technical information required for the development of a basic steady-state process simulation of the vitrification treatment train of sodium bearing waste (SBW) at Idaho National Engineering and Environmental Laboratory (INEEL) is presented. The objective of the modeling effort is to provide the predictive capability required to optimize an entire treatment train and assess system-wide impacts of local changes at individual unit operations, with the aim of reducing the schedule and cost of future process/facility design efforts. All the information required a priori for engineers to construct and link unit operation modules in a commercial software simulator to represent the alternative treatment trains is presented. The information is of a mid- to high-level nature and consists of the following: (1) a description of twenty-four specific unit operations--their operating conditions and constraints, primary species and key outputs, and the initial modeling approaches that will be used in the first year of the simulation's development; (2) three potential configurations of the unit operations (trains) and their interdependencies via stream connections; and (3) representative stream compositional makeups

  16. Virtual Reality in Presentation of the Underground Mine Technological Process

    Directory of Open Access Journals (Sweden)

    Kodym Oldøich

    2003-09-01

    Full Text Available Virtual Reality in Presentation of the Underground Mine Technological Process focuses on methods of presentation of an underground mine technologies in intranet technology. It shows usage of platform independent VRML client for presentation of static and dynamic information about technological process. Bi-directional interactions between client and process information database are solved.Based on analysis of technological process of underground mine a database structure was designed. It is skeleton for storing all information about any underground mine. This skeleton can be modified in any direction. Data in this "static model" of underground mine can be applied for visualization in VRML environment. In this way it is possible to simplify and unify a user's front-end for all kinds of tasks.All designed scenes can be interactively displayed in full view or in any detail view, so that a user is able to recognize every important part of installed equipment, its stage, technical parameters and other information. If manufacturers of mining equipment will supply VRML model of their real products everybody would be able to place it into VRML scene and learn everything about it.This work explores and tries to enlighten some of the areas and available approaches compliant with VRML 97 specification of modifying static scene by its browser. Concepts of animation pipeline, inside and outside scripting in scene displayed and authoring of VRML targeted geometry are discussed including database connectivity.

  17. Virtual Power Plant. Environmental Technology Management Tools of The Settlement Processes

    Directory of Open Access Journals (Sweden)

    Maurizio Sibilla

    2014-05-01

    Full Text Available The Distributed Energy Resource (DER systems represent a possible option for the implementation of the Low Carbon Cities development scenario, consistently with EU orientations. Many surveys, especially of engineering and information technology origin, are contributing to DER systems spread through testing the Virtual Power Plan (VVP: a technological system aimed at synchronously managing the information and energy fluxes, and able to have an effect on the urban metabolism balance and on the energy chain organizational model.  In the event of a wider VVP spread, consequences for the urban structure social and technical conversion process might be envisioned. Such systems gain importance in terms of starting urban renewal processes, introducing new rules for the local energy and environmental infrastructures.  In this way, it is envisioned the need for a deeper comprehension of the VVP innovative functionalities, this comprehension being significant for all the branches of knowledge which are interested in developing methods and tools for the Environmental Technology Management and Planning of the settlement processes.  The author, who is interested in producing and organizing an energy, distributed, renewable and interactive model, shows, through a critical analysis of the Electricity Networks Europe program study cases, the operating potential of the new system, emphasizing the consequences on the settlement process development, thus providing a first definition of the strategic features for the VVP technical and social implementation.

  18. Advances in fntd technology: Instrumentation, image processing and applications

    Science.gov (United States)

    Bartz, James Andrew

    Fluorescent Nuclear Track Detectors (FNTDs), based on Al2O 3:C,Mg single crystal material, enable diffraction limited imaging of ionization patterns. This fast, luminescent material is thermally and optically stable. This work expands and assesses the capability of FNTD technology to measure radiation dose quickly and accurately, especially neutron radition. Developments in FNTD instrumentation, software, image reconstruction, image processing and data processing improved ease of use, productivity and reliability and brought the technology into commercial viability. Descriptions of these developments are presented. Additionally, these developments were assessed and were found to comply with ANSI and ISO standards for personnel neutron dosimetry. (Abstract shortened by ProQuest.).

  19. Natural language processing in psychiatry. Artificial intelligence technology and psychopathology.

    Science.gov (United States)

    Garfield, D A; Rapp, C; Evens, M

    1992-04-01

    The potential benefit of artificial intelligence (AI) technology as a tool of psychiatry has not been well defined. In this essay, the technology of natural language processing and its position with regard to the two main schools of AI is clearly outlined. Past experiments utilizing AI techniques in understanding psychopathology are reviewed. Natural language processing can automate the analysis of transcripts and can be used in modeling theories of language comprehension. In these ways, it can serve as a tool in testing psychological theories of psychopathology and can be used as an effective tool in empirical research on verbal behavior in psychopathology.

  20. Methodology and Results of Mathematical Modelling of Complex Technological Processes

    Science.gov (United States)

    Mokrova, Nataliya V.

    2018-03-01

    The methodology of system analysis allows us to draw a mathematical model of the complex technological process. The mathematical description of the plasma-chemical process was proposed. The importance the quenching rate and initial temperature decrease time was confirmed for producing the maximum amount of the target product. The results of numerical integration of the system of differential equations can be used to describe reagent concentrations, plasma jet rate and temperature in order to achieve optimal mode of hardening. Such models are applicable both for solving control problems and predicting future states of sophisticated technological systems.

  1. Development of a procedure for evaluating the economics of process options in commercial HTGR fuel cycle

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, W.E.

    1976-05-01

    The report presented describes the status of and calculational procedures used in a machine code being developed for calculating costs of fresh fuel fabrication, chemical reprocessing, and refabrication of HTGR fuel. In its present state of development, the capability is confined principally to calculating annual mainstream and scrap recovery process throughputs in fresh fuel fabrication, chemical reprocessing, and refabrication. The code works from user-supplied reactor build schedules and fuel specifications to approximate changing fuel fabrication requirements over a 20-year (maximum) projection. The availability of a reprocessing facility may be delayed to some specified date beyond the first year of a projection. Some of the cost routines have also been programmed and are described.

  2. Chemo‐enzymatic epoxidation–process options for improving biocatalytic productivity

    DEFF Research Database (Denmark)

    Hagström, Anna E. V.; Törnvall, Ulrika; Nordblad, Mathias

    2011-01-01

    The reactor choice is crucial when designing a process where inactivation of the biocatalyst is a problem. The main bottleneck for the chemo‐enzymatic epoxidation has been found to be enzyme inactivation by the hydrogen peroxide, H2O2, substrate. In the work reported here, the effect of reaction...... parameters on the reaction performance have been investigated and used to establish suitable operating strategies to minimize the inactivation of the enzyme, using rapeseed methyl ester (RME) as a substrate in a solvent‐free system. The use of a controlled fed‐batch reactor for maintaining H2O2 concentration...... at 1.5 M resulted in increased productivity, up to 76 grams of product per gram of biocatalyst with higher retention of enzyme activity. Further investigation included a multistage design that separated the enzymatic reaction and the saturation of the RME substrate with H2O2 into different vessels...

  3. Indonesian options

    NARCIS (Netherlands)

    Anderluh, J.H.M.; van der Weide, J.A.M.

    2006-01-01

    Jakarta Stock Exchange Indonesia has started to trade Indonesian options at September 9th, 2004. An Indonesian option can be considered as an American style barrier option with immediate (forced) exercise if the price hits or crosses the barrier before maturity. The payoff of the option is based on

  4. The impact of the different payment options on the medical services clients' satisfaction building process

    Science.gov (United States)

    Skowron, Łukasz; Gąsior, Marcin; Sak-Skowron, Monika

    2014-12-01

    Both the scientific bodies as well as business practitioners over the past few years have concentrated their efforts in the field of marketing and management primarily around the concept of customer, wanting to know more about him/her and trying to understand their behaviour so that their market activities can more easily be influenced and shaped. In today's market, the customer bases the purchase-decision-making process on choosing a good/service that will give him/her the greatest satisfaction, a subjective, positive experience, which is an emotional reaction to the perceived value. Its level is a result of the comparison between the level of expectations arising from past experience, obtained information and promises, and the perception of experienced situation. In the empirical part of the manuscript, the authors present the main differences in the process of building customer satisfaction and loyalty for two groups of patients: those using prepaid medical services and those who pay for their services each time. Reported results refer to research carried out by the authors between August and October 2012 in the city of Warsaw (Poland) with use of the Structural Equation Modeling analysis. The study was conducted via paper surveys, on a sample of 1590 respondents who were the patients of selected medical organizations. The study demonstrated, using two, separate models, that among aforementioned groups of patients, the evaluation of health services proceeds in quite a different way. This indicates significant implications, of marketing and management character in the field of communication and building long-term patient-organization relationships. Medical establishments wanting to manage effectively their relationships with current and potential customers need to understand the nature of the different groups of patients and be able to adjust the scope and form of marketing activities to their different expectations and preferences.

  5. MODEL OF QUALITY MANAGEMENT OF TECHNOLOGICAL PROCESSES OF THE GRAIN PROCESSING AND MILL ENTERPRISES

    Directory of Open Access Journals (Sweden)

    M. M. Blagoveshchenskaia

    2014-01-01

    Full Text Available Summary. In the work the model of quality management of technological processes of the grain processing and mill enterprises is presented. It is shown that flour-grinding production is an important part of agro-industrial complex because it provides production of the main food product of people – flour. The analytical indicators of quality of technological process are presented. The matrix of expert estimates of i-th level of quality for the set combinations of parameters values according to the scheme of complete factorial experiment is made. Considered a model for the calculation of the raw material preparation for milling, which characterizes the main qualities of the processed raw materials. For the purpose of management of quality of technological processes of flour mill the mathematical model which includes calculation of two groups of indicators of an assessment is developed: qualities of preparation of raw materials for a grinding and qualities of conducting technological process. The algorithm of an analytical assessment of indicators of quality of technological process of the flour-grinding enterprises, including the selection of waste, selection of bran, a compliance rate of output of flour-grinding products, compliance rate of moisture products, is offered. The assessment of quality management of technological process of a high-quality grinding on the example of several leading flour-grinding enterprises of Central Federal District is carried out. The two-dimensional model of quality management of technological process based on an analytical indicators of an assessment of quality, an assessment of quality of preparation the raw materials for a grinding and an optimum effective condition of technological process is constructed. It is shown that quality management at the enterprise provides collecting, processing and the analysis of information on a condition of material streams and productions on all of their stages.

  6. New media technologies and mass media reform processes

    Directory of Open Access Journals (Sweden)

    Tomić Boban

    2017-01-01

    Full Text Available This paper reviews and assesses the chances for survival and development of the media in Serbia and ib the region, from the perspective of new information and communication technologies (ICT applied in media business. In the paper theoretical method is used and harmonized with the needs of describing the problems and the observed processes and phenomena, as well as empirical method which is used for collecting and interpreting concrete facts and data on the observed processes and phenomena. The starting point lies in the fact that modern media is definitely, more and more, dependent on new technologies. A part of the new technologies is used in the process of collecting, selecting and editing media content, while the other part of the technology is used in the process of dissemination and propulsion of media content to the mass audience, and also in the feedback function as well. The technology revolution, which we describe, started with mp3, jpg and avi files, and continues with internet broadcasting, social networks, cloud technologies and new digital platforms which are used by today's media for distribution of media content. The particularity of the media in the region lies in the fact that they operating in the societes with delay of political and economic transition, so all the productive resources of society, due to this backlog, are slower adapted to the new conditions of business in the digital era. The consequences that have arisen from such dynamics of development make many media in Serbia and the region quite dysfunctional, especially those who were exposed during this transition to long-standing legal, economic and program crises. That is why most of the existing media in Serbia, especially small ones, are unprepared for modernization and they are not ready for re-modeling in accordance with the new technological circumstances.

  7. Some novel concepts in radiation processing technology applications

    International Nuclear Information System (INIS)

    Varshney, Lalit

    2014-01-01

    Search for better materials and processes has been a part of the evolution of mankind and it still continues to be so as it is being realized that earth's resources are not everlasting and effect of rapid growth on environment may adversely affect the future development. Sustainable development is the only choice for today for long term survival. Better quality and high functional materials, made by superior technologies are being demanded by the society. Radiation processing technology has significantly contributed to meet the expectation of the people in providing superior products and processes while preserving the environment. Processes are being developed where resources are fully utilized with maximum advantages and little disturbance to the environment. More than 1500 electron beam accelerators and about 500 Gamma Irradiators are presently in use and many are being deployed for radiation processing of medical supplies, pharmaceuticals and herbal materials, treat effluents and preserve food and agricultural products and several industrial products. DAE has an ambitious plan to deploy radiation technology for societal benefits in India. In the presentations some interesting applications of Radiation Processing Technology will be discussed which includes (1) Radiation Processing of Cashew Apple fruit for bio-ethanol production (2) High Energy Battery separators (3) Plant Growth Promoters and (4) Tunable biodegradability. The discussion would reveal how a waste product like cashew apple can be converted to useful materials and advanced materials like HEB separators and Tunable Biodegradable films can be made using radiation technology. Use of radiation de-polymerized polysaccharides in some experiments have shown unexpected increase in agriculture output giving new concepts to increase the productivity. (author)

  8. NEXT GENERATION MELTER OPTIONEERING STUDY - INTERIM REPORT

    Energy Technology Data Exchange (ETDEWEB)

    GRAY MF; CALMUS RB; RAMSEY G; LOMAX J; ALLEN H

    2010-10-19

    The next generation melter (NOM) development program includes a down selection process to aid in determining the recommended vitrification technology to implement into the WTP at the first melter change-out which is scheduled for 2025. This optioneering study presents a structured value engineering process to establish and assess evaluation criteria that will be incorporated into the down selection process. This process establishes an evaluation framework that will be used progressively throughout the NGM program, and as such this interim report will be updated on a regular basis. The workshop objectives were achieved. In particular: (1) Consensus was reached with stakeholders and technology providers represented at the workshop regarding the need for a decision making process and the application of the D{sub 2}0 process to NGM option evaluation. (2) A framework was established for applying the decision making process to technology development and evaluation between 2010 and 2013. (3) The criteria for the initial evaluation in 2011 were refined and agreed with stakeholders and technology providers. (4) The technology providers have the guidance required to produce data/information to support the next phase of the evaluation process. In some cases it may be necessary to reflect the data/information requirements and overall approach to the evaluation of technology options against specific criteria within updated Statements of Work for 2010-2011. Access to the WTP engineering data has been identified as being very important for option development and evaluation due to the interface issues for the NGM and surrounding plant. WRPS efforts are ongoing to establish precisely data that is required and how to resolve this Issue. It is intended to apply a similarly structured decision making process to the development and evaluation of LAW NGM options.

  9. Wireless sensor technology for in-situ plasma process monitoring

    Science.gov (United States)

    Gahan, David

    2015-09-01

    There is an increasing demand for plasma measurement and control solutions to cope with the growing complexity of integrated circuit manufacture in the semiconductor industry. Standard plasma diagnostic instruments used in research, such as the Langmuir probe, are not suitable for use in the production environment for myriad reasons - contamination of the process being one of the main concerns. Silicon wafer based wireless sensors, which measure temperature during the process, have gained the most traction with tool manufacturers and chip makers - albeit during process development or the PM cycle rather than live production. In this presentation we will discuss two novel wireless technologies that have the potential for use in process tools. The first is an ion detector embedded in a silicon wafer. The sensor measures the average ion flux and the maximum ion energy during the process. This information is stored and is downloaded later for analysis. The second technology consists of a wireless sensor that sits inside the process and communicates data in real time to a detector installed on the rf power line. This platform is similar to RFID technology and can be combined with various sensor types to transmit data to the user during the process.

  10. Lipid Processing Technology: Building a Multilevel Modeling Network

    DEFF Research Database (Denmark)

    Díaz Tovar, Carlos Axel; Mustaffa, Azizul Azri; Mukkerikar, Amol

    2011-01-01

    of a master parameter table; iii) development of a model library consisting of new and adopted process models of unit operations involved in lipid processing technologies, validation of the developed models using operating data collected from existing process plants, and application of validated models......The aim of this work is to present the development of a computer aided multilevel modeling network for the systematic design and analysis of processes employing lipid technologies. This is achieved by decomposing the problem into four levels of modeling: i) pure component property modeling...... and a lipid-database of collected experimental data from industry and generated data from validated predictive property models, as well as modeling tools for fast adoption-analysis of property prediction models; ii) modeling of phase behavior of relevant lipid mixtures using the UNIFACCI model, development...

  11. Pretreatment Technologies of Lignocellulosic Materials in Bioethanol Production Process

    Directory of Open Access Journals (Sweden)

    Mohamad Rusdi Hidayat

    2013-06-01

    Full Text Available Bioethanol is one type of biofuel that developed significantly. The utilization of bioethanol is not only limited for fuel, but also could be used as material for various industries such as pharmaceuticals, cosmetics, and food. With wide utilization and relatively simple production technology has made bioethanol as the most favored biofuel currently. The use of lignocellulosic biomass, microalgae, seaweeds, even GMO (Genetically modified organisms as substrates for bioethanol production has been widely tested. Differences in the materials eventually led to change in the production technology used. Pretreatment technology in the bioethanol production using lignocellulosic currently experiencing rapid development. It is a key process and crucial for the whole next steps. Based on the advantages and disadvantages from all methods, steam explotion and liquid hot water methods are the most promising  pretreatment technology available.

  12. Biomass waste-to-energy valorisation technologies: a review case for banana processing in Uganda.

    Science.gov (United States)

    Gumisiriza, Robert; Hawumba, Joseph Funa; Okure, Mackay; Hensel, Oliver

    2017-01-01

    Uganda's banana industry is heavily impeded by the lack of cheap, reliable and sustainable energy mainly needed for processing of banana fruit into pulp and subsequent drying into chips before milling into banana flour that has several uses in the bakery industry, among others. Uganda has one of the lowest electricity access levels, estimated at only 2-3% in rural areas where most of the banana growing is located. In addition, most banana farmers have limited financial capacity to access modern solar energy technologies that can generate sufficient energy for industrial processing. Besides energy scarcity and unreliability, banana production, marketing and industrial processing generate large quantities of organic wastes that are disposed of majorly by unregulated dumping in places such as swamps, thereby forming huge putrefying biomass that emit green house gases (methane and carbon dioxide). On the other hand, the energy content of banana waste, if harnessed through appropriate waste-to-energy technologies, would not only solve the energy requirement for processing of banana pulp, but would also offer an additional benefit of avoiding fossil fuels through the use of renewable energy. The potential waste-to-energy technologies that can be used in valorisation of banana waste can be grouped into three: Thermal (Direct combustion and Incineration), Thermo-chemical (Torrefaction, Plasma treatment, Gasification and Pyrolysis) and Biochemical (Composting, Ethanol fermentation and Anaerobic Digestion). However, due to high moisture content of banana waste, direct application of either thermal or thermo-chemical waste-to-energy technologies is challenging. Although, supercritical water gasification does not require drying of feedstock beforehand and can be a promising thermo-chemical technology for gasification of wet biomass such as banana waste, it is an expensive technology that may not be adopted by banana farmers in Uganda. Biochemical conversion technologies are

  13. A Voice Processing Technology for Rural Specific Context

    Science.gov (United States)

    He, Zhiyong; Zhang, Zhengguang; Zhao, Chunshen

    Durian the promotion and applications of rural information, different geographical dialect voice interaction is a very complex issue. Through in-depth analysis of TTS core technologies, this paper presents the methods of intelligent segmentation, word segmentation algorithm and intelligent voice thesaurus construction in the different dialects context. And then COM based development methodology for specific context voice processing system implementation and programming method. The method has a certain reference value for the rural dialect and voice processing applications.

  14. [Inheritance and innovation of traditional processing technology of Chinese medicine].

    Science.gov (United States)

    Yang, Ming; Zhong, Ling-Yun; Xue, Xiao; Liu, Rong-Hua; Gong, Qian-Feng

    2016-02-01

    To discuss the inheritance and innovation study of Chinese medicine processing technology from three aspects: inheritance, standardization and industrial innovation development, propose "three lacks" in inheritance, "six lacks of standardization, and one lack of unity" in standardization, and "three emphasizing and three despising aspects" in industrial innovation, and propose feasible solutions for the above mentioned problems, providing a good foundation for inheritance and innovation of Chinese medicine processing. Copyright© by the Chinese Pharmaceutical Association.

  15. Moulded Pulp Manufacturing: Overview and Prospects for the Process Technology

    DEFF Research Database (Denmark)

    Didone, Mattia; Saxena, Prateek; Meijer, Ellen Brilhuis

    2017-01-01

    . The goal of this paper is to give an overview of the main aspects involved in the manufacture of moulded pulp products. This includes a classification of moulded pulp products, historical and current applications, production processes, materials, mechanical properties and environmental sustainability....... Moreover, based on the latest research in the field, an innovative drying technique that utilizes concepts derived from impulse drying is presented, and the implementation of this process technology is discussed....

  16. Microscale technology and biocatalytic processes: Opportunities and challenges for synthesis

    DEFF Research Database (Denmark)

    Wohlgemuth, Roland; Plazl, Igor; Žnidaršič-Plazl, Polona

    2015-01-01

    Despite the expanding presence of microscale technology in chemical synthesis and energy production as well as in biomedical devices and analytical and diagnostic tools, its potential in biocatalytic processes for pharmaceutical and fine chemicals, as well as related industries, has not yet been ......, and the future outlook for the implementation of these key green engineering methods and the role of supporting tools such as mathematical models to establish sustainable production processes are discussed....

  17. Status of electron beam processing technology in Malaysia

    International Nuclear Information System (INIS)

    Ghazali, Zulkafli; Dahlan, Khairul Zaman; Aiasah, S.H.; Khomsaton, A.B.; Ting, T.M.

    2003-01-01

    The electron beam processing in Malaysia starting in 1991 at MINT (Malaysian Institute for Nuclear Technology Research) has been focussed on medical product sterilization, curing of surface coating and polymer modifications. Subsequent installation of accelerators by private companies promoted the development of radiation processing technologies for the use of production of heat-shrinkable products, pilot-scale flue gas purification, as well as wires, cables, tubes and hydrogels. Decomposition of a wide range of volatile organic compounds from industrial exhausts (car painting lines, volatile dioxin and furan from municipal waste incinerators) and purification of liquid wastewater and drinking water are also being under R and D work. Malaysia will continue to play an active part in the program on radiation technology to strengthen environmentally sustainable development in line with FNCA objectives. (S. Ohno)

  18. DUPIC nuclear fuel manufacturing and process technology development at KAERI

    International Nuclear Information System (INIS)

    Yim, Sung Paal; Lee, Jung Won; Kim, Jong Ho; Kim, Soo Sung; Kim, Woong Ki; Yang, Myung Seung

    2000-01-01

    DUPIC fuel cycle development project in KAERI of Korea was initiated in 1991 and has advanced in relevant technologies for last 10 years. The project includes five different topics such as nuclear fuel manufacturing, compatibility evaluation, performance evaluation, manufacturing facility management, and safeguards. The contents and results of DUPIC R and D up to now are as follow: - the basic foundation was established for the critically required pelletizing technology and powder treatment technology for DUPIC. - development of DUPIC process line and deployment of 20 each process equipment and examination instruments in DFDF. - powder and pellet characterization study was done at PIEF based on the simfuel study results, and 30 DUPIC pellets were successfully produced. - the manufactured pellets were used for sample fuel rods irradiated in July,2000 in HANARO research reactor in KAERI and has been under post irradiation examination. (Hong, J. S.)

  19. Use of indigenous technology in processing and utilization of non ...

    African Journals Online (AJOL)

    Information used for this paper came from both primary and secondary sources. Ten (10) respondents were interviewed from each secondary source of information. The use of indigenous technology to process these forest products to forest foods is currently limited by use of crude methods, inability to expand production ...

  20. Lipid Processing Technology: Building a Multilevel Modeling Network

    DEFF Research Database (Denmark)

    Díaz Tovar, Carlos Axel; Mustaffa, Azizul Azri; Mukkerikar, Amol

    2011-01-01

    The aim of this work is to present the development of a computer aided multilevel modeling network for the systematic design and analysis of processes employing lipid technologies. This is achieved by decomposing the problem into four levels of modeling: i) pure component property modeling...

  1. Adoption of improved technologies in soyabean processing and ...

    African Journals Online (AJOL)

    adequate information and limited understanding. To increase protein food intake, adoption of soyabean improved technologies should be encouraged. Efforts should be made by extension workers to create more awareness on the importance of these innovations and on methods of processing. This way, consumption of ...

  2. An assessment of oil processing methods and technology in Taraba ...

    African Journals Online (AJOL)

    Objective: The study assessed the various methods and technology of vegetable oil processing in Taraba State. Methods: A total of 250 questionnaires were administered to vegetable oil processors with indepth interview of 28 respondents who were randomly selected based on a preliminary study in six (6) Local ...

  3. Transition process from emerging NDT technology to production inspection application

    Science.gov (United States)

    Jappe, William; Wood, Nancy; Johnson, Maurice

    1995-07-01

    The successful application of emerging NDT technologies for specific aging aircraft inspections requires an integration of efforts between aircraft operators, airframe manufacturers, NDT equipment designers, and government regulators. This paper describes the development process that was followed to establish an alternate inspection technique for a DC-10 crown skin butt joint inspection. Initial investigation, intermediate development, and final evaluations are discussed.

  4. Perception of Modern Processing Technology by Shea Butter ...

    African Journals Online (AJOL)

    The study examined the perception of Shea butter processors to modern processing technology in Kwara State. Multi stage sampling procedure was used to select 120 respondents. Data was collected using interview schedule and analysed with both descriptive and inferential statistics. Results revealed that 88.3% of the ...

  5. Pellet manufacturing by extrusion-spheronization using process analytical technology

    DEFF Research Database (Denmark)

    Sandler, Niklas; Rantanen, Jukka; Heinämäki, Jyrki

    2005-01-01

    The aim of this study was to investigate the phase transitions occurring in nitrofurantoin and theophylline formulations during pelletization by extrusion-spheronization. An at-line process analytical technology (PAT) approach was used to increase the understanding of the solid-state behavior of ...

  6. Sustaining high energy efficiency in existing processes with advanced process integration technology

    International Nuclear Information System (INIS)

    Zhang, Nan; Smith, Robin; Bulatov, Igor; Klemeš, Jiří Jaromír

    2013-01-01

    Highlights: ► Process integration with better modelling and more advanced solution methods. ► Operational changes for better environmental performance through optimisation. ► Identification of process integration technology for operational optimisation. ► Systematic implementation procedure of process integration technology. ► A case study with crude oil distillation to demonstrate the operational flexibility. -- Abstract: To reduce emissions in the process industry, much emphasis has been put on making step changes in emission reduction, by developing new process technology and making renewable energy more affordable. However, the energy saving potential of existing systems cannot be simply ignored. In recent years, there have been significant advances in process integration technology with better modelling techniques and more advanced solution methods. These methods have been applied to the new design and retrofit studies in the process industry. Here attempts are made to apply these technologies to improve the environmental performance of existing facilities with operational changes. An industrial project was carried out to demonstrate the importance and effectiveness of exploiting the operational flexibility for energy conservation. By applying advanced optimisation technique to integrate the operation of distillation and heat recovery in a crude oil distillation unit, the energy consumption was reduced by 8% without capital expenditure. It shows that with correctly identified technology and the proper execution procedure, significant energy savings and emission reduction can be achieved very quickly without major capital expenditure. This allows the industry to improve its economic and environment performance at the same time.

  7. Development of new processing technology for ruminant feed

    International Nuclear Information System (INIS)

    Mat Rasol Awang; Hassan Hamdani Mutaat; Zainun Said; Alias Saidali; Erwan Md Ariff

    2002-01-01

    The technology for production ruminant feed from agriculture by-product remains scare despite plentiful availability of feeding materials worldwide. Factors that prohibit the process technology development suggested that their peculiar physical make up, high cost of production and inferior product quality compared to established raw material, had consequently impeding the effort. In Malaysia, only two pilot plants exist; they demonstrate utilization of Oil Palm Frond (OPF) into feed. In the case of OPF in situ utilization as feed, farmers use chipper machine or shredder to process it. Other by-products have not been successfully exploited, except for Palm Kernel Cake (PKC) and Palm Oil Mill Effluent (POME) that already in commercial operation. In view of the by-product availability as feeding material in ruminant feeding system and availability of new chipper and shredder machines, the prospect of processing agriculture by-products into feed is expected to be a promising business venture. This paper describes the technology for production of new feed from oil palm Empty Fruit Bunch (EFB). It elaborates on Sterifeed Plant Operation based on plant capacity of 0.5 ton/day production. The operation aspects discuss raw materials handling and processing as well as transforming the products into marketable forms. In this process EFB is initially predigested by fungi in solid state fermentation process into feed materials; the product is ready to be fed in fresh form to animal. The operation exercise has established actual process flow, identified problems and process drawbacks. Based on this experience, availability of localized raw materials EFB at the palm oil mill and rapid development of processing machinery, it is very likely that a commercially viable feed processing plant can be established in the near future. In addition, establishing more data on product quality by further test and characterization of the new feed may contribute to success of the project. (Author)

  8. Accelerating process and catalyst development in reforming reactions with high throughput technologies under industrially relevant conditions

    Energy Technology Data Exchange (ETDEWEB)

    Schunk, S.A.; Bollmann, G.; Froescher, A.; Kaiser, H.; Lange de Oliveira, A.; Roussiere, T.; Wasserschaff, G. [hte Aktiengesellschaft, Heidelberg (Germany); Domke, I. [BASF SE, Ludwigshafen (Germany)

    2010-12-30

    The generation of hydrogen via reforming of a variety of carbon containing feed-stocks in the presence of water is up to date one of the most versatile technologies for the production of hydrogen and syngas. Although these reforming technologies are in principle well established, understood and commercialized, there are still a number of technological challenges that are not solved up to a satisfactorily degree and there is a constant demand for appropriate answers to the challenges posed. High throughput experimentation can be a valuable tool in helping accelerate the development of suitable solutions on the catalyst and process development side. In order to be able to generate test data that are close or identical to process relevant conditions, hte has developed a new technology portfolio of test technologies named Stage-IV technology. In contrast to earlier developments which address more small scale testing on the basis of catalyst volumes of 1ml up to 10 ml under isothermal conditions, our new technology portfolio offers the advantage of test volumes at sub-pilot scale also realizing reactor dimensions close to technical applications. This does not only ensure a good mimic of the hydrodynamic conditions of the technical scale, but also allows a fingerprinting of features like temperature gradients in the catalyst bed which play a large role for catalyst performance. Apart from catalyst tests with granulates when screening for optimized catalyst compositions, the units are designed to accommodate tests with shaped catalysts. In order to demonstrate how these technologies can accelerate catalyst and process development we have chosen technically challenging application examples: (I) Pre-reforming and reforming of methane based feeds which accelerate coking and catalyst deactivation. Higher reaction pressures, high CO{sub 2} contents in the feedgas (which occur typically in sources like bio-gas or certain types of natural gas), the presence of higher alkanes

  9. The role of new technologies in the decision-making process

    Directory of Open Access Journals (Sweden)

    Marina Budimir

    2013-12-01

    Full Text Available Given the fact that a decision-making environment is subject to change due to the development of new technologies, networking of an individual or an organisation within and towards external environment as well as contemporary communication methods that facilitate a continuous inflow, outflow and exchange of data and information, the requirements set before decision-makers are more demanding than ever. In such contemporary conditions, the process of collecting, analyzing and selecting data and information for the purpose of making quality decisions depending on potential limitations and available options, and finally making decisions as the basis for future behaviour, whether of an individual or an organisation, is becoming more complex. New technologies provide a number of possibilities that facilitate the decision-making pro - cess. However, the decision-maker should still be able to choose the right models, methods, tools, systems and procedures for a particular situation, with the aim of arriving at an appropriate and timely decision. The purpose of this paper is to describe in detail the theoretical underpinnings of decision-making; explain the decision-making model and the decision-making process. Given the fact that decision-making can affect the course of the activities pursued by the decision-maker in the short or long term depending on the consequences of the decision, this paper will examine the latest software solutions that simplify decision- making, and clarify the role of new technologies in the process of decision-making in business and private life.

  10. Modern processing technologies and food quality. 18th Food Technology Days '97 dedicated to prof. F. Bitenc

    International Nuclear Information System (INIS)

    Zlender, Bozidar; Gasperlin, Lea; Hocevar, Ivica; Slemenik, Barbka; Hocevar, Polona

    1997-01-01

    Modern processing technologies and food quality. Proceedings of thematic survey of topics in food science and technology and nutrition for postgraduate students, Ljubljana Univ. (Slovenia). Biotechnical Fac., Food Science and Technology Dept

  11. TANK SPACE OPTIONS REPORT

    Energy Technology Data Exchange (ETDEWEB)

    WILLIS WL; AHRENDT MR

    2009-08-11

    Since this report was originally issued in 2001, several options proposed for increasing double-shell tank (DST) storage space were implemented or are in the process of implementation. Changes to the single-shell tank (SST) waste retrieval schedule, completion of DST space saving options, and the DST space saving options in progress have delayed the projected shortfall of DST storage space from the 2007-2011 to the 2018-2025 timeframe (ORP-11242, River Protection Project System Plan). This report reevaluates options from Rev. 0 and includes evaluations of new options for alleviating projected restrictions on SST waste retrieval beginning in 2018 because of the lack of DST storage space.

  12. Recent Advances in Food Processing Using High Hydrostatic Pressure Technology.

    Science.gov (United States)

    Wang, Chung-Yi; Huang, Hsiao-Wen; Hsu, Chiao-Ping; Yang, Binghuei Barry

    2016-01-01

    High hydrostatic pressure is an emerging non-thermal technology that can achieve the same standards of food safety as those of heat pasteurization and meet consumer requirements for fresher tasting, minimally processed foods. Applying high-pressure processing can inactivate pathogenic and spoilage microorganisms and enzymes, as well as modify structures with little or no effects on the nutritional and sensory quality of foods. The U.S. Food and Drug Administration (FDA) and the U.S. Department of Agriculture (USDA) have approved the use of high-pressure processing (HPP), which is a reliable technological alternative to conventional heat pasteurization in food-processing procedures. This paper presents the current applications of HPP in processing fruits, vegetables, meats, seafood, dairy, and egg products; such applications include the combination of pressure and biopreservation to generate specific characteristics in certain products. In addition, this paper describes recent findings on the microbiological, chemical, and molecular aspects of HPP technology used in commercial and research applications.

  13. Strategies for Derisking Translational Processes for Biomedical Technologies.

    Science.gov (United States)

    Abou-El-Enein, Mohamed; Duda, Georg N; Gruskin, Elliott A; Grainger, David W

    2017-02-01

    Inefficient translational processes for technology-oriented biomedical research have led to some prominent and frequent failures in the development of many leading drug candidates, several designated investigational drugs, and some medical devices, as well as documented patient harm and postmarket product withdrawals. Derisking this process, particularly in the early stages, should increase translational efficiency and streamline resource utilization, especially in an academic setting. In this opinion article, we identify a 12-step guideline for reducing risks typically associated with translating medical technologies as they move toward prototypes, preclinical proof of concept, and possible clinical testing. Integrating the described 12-step process should prove valuable for improving how early-stage academic biomedical concepts are cultivated, culled, and manicured toward intended clinical applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Introduction of Virtualization Technology to Multi-Process Model Checking

    Science.gov (United States)

    Leungwattanakit, Watcharin; Artho, Cyrille; Hagiya, Masami; Tanabe, Yoshinori; Yamamoto, Mitsuharu

    2009-01-01

    Model checkers find failures in software by exploring every possible execution schedule. Java PathFinder (JPF), a Java model checker, has been extended recently to cover networked applications by caching data transferred in a communication channel. A target process is executed by JPF, whereas its peer process runs on a regular virtual machine outside. However, non-deterministic target programs may produce different output data in each schedule, causing the cache to restart the peer process to handle the different set of data. Virtualization tools could help us restore previous states of peers, eliminating peer restart. This paper proposes the application of virtualization technology to networked model checking, concentrating on JPF.

  15. Improving Logistics Processes in Industry Using Web Technologies

    Directory of Open Access Journals (Sweden)

    Jánošík Ján

    2016-12-01

    Full Text Available The aim of this paper is to propose the concept of a system that takes advantage of web technologies and integrates them into the management process and management of internal stocks which may relate to external applications and creates the conditions to transform a Computerized Control of Warehouse Stock (CCWS in the company. The importance of implementing CCWS is in the elimination of the claims caused by the human factor, as well as to allow the processing of information for analytical purposes and their subsequent use to improve internal processes. Using CCWS in the company would also facilitate better use of the potential tools Business Intelligence and Data Mining.

  16. HTR process heat applications, status of technology and economical potential

    International Nuclear Information System (INIS)

    Barnet, H.

    1997-01-01

    The technical and industrial feasibility of the production of high temperature heat from nuclear fuel is presented. The technical feasibility of high temperature heat consuming processes is reviewed and assessed. The conclusion is drawn that the next technological step for pilot plant scale demonstration is the nuclear heated steam reforming process. The economical potential of HTR process heat applications is reviewed: It is directly coupled to the economical competitiveness of HTR electricity production. Recently made statements and pre-conditions on the economic competitiveness in comparison to world market coal are reported. (author). 8 figs

  17. Technology and equipment for processing diamond materials of modern electronics

    Directory of Open Access Journals (Sweden)

    Mityagin A. Yu.

    2009-02-01

    Full Text Available The methods of selection and sorting of diamonds according to their physical properties by modern physical methods of the analysis are developed, as well as the technologies of precision laser cutting of diamonds, their processing on a basis of thermochemical reactions in gas environment. The experimental installation for polishing and grinding of diamond plates, installation for slicing, installation for plasma-chemical processing are created. The techniques of surface roughness measurement of the processed plates and control of roughness parameters are developed. Some experimental results are given.

  18. INFORMATION TECHNOLOGIES IN THE PROCESS OF TRAINING MARITIME SPECIALISTS

    Directory of Open Access Journals (Sweden)

    Ulyana Lyashenko

    2015-10-01

    Full Text Available The article represents main questions concerning usage of the newest information-communicative technologies of maritime educational establishments in the process of training specialists of corresponding specialities; reviews the problem of training cadets of Maritime educational institutions by means of information technologies while studying professionally focused disciplines; means of implementation information technologies into the educational process and their practical usage in future professional activity on board a ship are disclosed; the importance of online communications in teaching foreign language speaking, listening comprehension, writing and test tasks implementation to control forming of cadet’s lexical, phonetic and grammar skills are proved; presentations of authentic professionally oriented materials from the newest electronic sources on lectures on disciplines «Marine diesel installations», «Power management system», «Radio-navigational devices and systems». The author of the article grounds practicability of implementation of the newest information communicative technologies into educational process in classroom and extracurricular work, cadets are given an opportunity to get authentic professionally focused information on professional discipline, to extend knowledge on these disciplines and to realize control of formation corresponding competences.

  19. Application of radiation technology to sewage sludge processing: A review

    International Nuclear Information System (INIS)

    Wang Jianlong; Wang Jiazhuo

    2007-01-01

    Sewage sludge is unwanted residual solid wastes generated in wastewater treatment and its management is one of the most critical environmental issues of today. The treatment and disposal of sludge contribute a considerable proportion of the cost for running a wastewater treatment plant. The increasing amount of swage sludge and more and more legislative regulation of its disposal have stimulated the need for developing new technologies to process sewage sludge efficiently and economically. One ideal consideration is to recycle it after proper treatment. Radiation technology is regarded to be a promising alternative for its high efficiency in pathogen inactivation, organic pollutants oxidation, odor nuisance elimination and some other characteristics enhancement, which will facilitate the down-stream process of sludge treatment and disposal. Here we present a brief review of application of radiation technology on sewage sludge processing. Some basic information of two currently available irradiation systems and fundamental radiation chemistry are introduced firstly; then the world-wide application of this promising technology is reviewed; various effects of radiation on sludge is discussed in detail; and some concluding remarks are given and some future directions are also proposed

  20. Knowledge and cognitive process dimensions of Technology teachers' lesson objectives

    Directory of Open Access Journals (Sweden)

    David Mathumbu

    2014-03-01

    Full Text Available A clearly stated lesson objective is considered an essential component of a well-planned lesson. Many teachers of Technology, a relatively new subject in South African schools, teach Technology with rather limited training both in content and methodological approaches. This study sought to investigate and classify lesson objectives framed or implied by teachers in their lesson plans according to knowledge and cognitive process dimensions. The two-dimensional Taxonomy Table introduced by Krathwohl was adapted for Technology and formed the framework for this study. It was found that most of the directly stated objectives are directed to the lower level of the cognitive process dimension and address mainly factual knowledge, while no activities or lesson components address meta-cognitive knowledge. Some lesson objectives inferred from planned assessment activities placed higher demands on learners' cognitive domain. A recommendation flowing from the study is that, during pre-service training and in-service teacher support processes, the importance of clear lesson objectives should be emphasised and that assessments planned for such lessons should closely match the lesson objectives. Further research is also needed on the reasons why low cognitive demands are made in the teaching of Technology.

  1. Application of Electro-Technologies in Processing of Flax Fiber

    Directory of Open Access Journals (Sweden)

    G. S. Vijaya Raghavan

    2013-08-01

    Full Text Available Flax fibers used for various applications are obtained from flax stems. Retting followed by drying and mechanical separation leads to the production of fibers. This review article discusses the application of electro-technologies in the production of bast fibers from the flax stem. In these technologies, flax stems harvested from the field are subjected to microwave assisted retting, followed by electro–osmotic dewatering which reduces the water content of the stems. Dewatered stems are transferred to a microwave chamber for further drying, thus retted stems are obtained for further processing.

  2. TECHNOLOGICAL PROCESS MODELING AIMING TO IMPROVE ITS OPERATIONS MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Ivan Mihajlović

    2011-11-01

    Full Text Available This paper presents the modeling procedure of one real technological system. In this study, thecopper extraction from the copper flotation waste generated at the Bor Copper Mine (Serbia, werethe object of modeling. Sufficient data base for statistical modeling was constructed using theorthogonal factorial design of the experiments. Mathematical model of investigated system wasdeveloped using the combination of linear and multiple linear statistical analysis approach. Thepurpose of such a model is obtaining optimal states of the system that enable efficient operationsmanagement. Besides technological and economical, ecological parameters of the process wereconsidered as crucial input variables.

  3. The Contextualized Technology Adaptation Process (CTAP): Optimizing Health Information Technology to Improve Mental Health Systems

    Science.gov (United States)

    Lyon, Aaron R.; Wasse, Jessica Knaster; Ludwig, Kristy; Zachry, Mark; Bruns, Eric J.; Unützer, Jürgen; McCauley, Elizabeth

    2015-01-01

    Health information technologies have become a central fixture in the mental healthcare landscape, but few frameworks exist to guide their adaptation to novel settings. This paper introduces the Contextualized Technology Adaptation Process (CTAP) and presents data collected during Phase 1 of its application to measurement feedback system development in school mental health. The CTAP is built on models of human-centered design and implementation science and incorporates repeated mixed methods assessments to guide the design of technologies to ensure high compatibility with a destination setting. CTAP phases include: (1) Contextual evaluation, (2) Evaluation of the unadapted technology, (3) Trialing and evaluation of the adapted technology, (4) Refinement and larger-scale implementation, and (5) Sustainment through ongoing evaluation and system revision. Qualitative findings from school-based practitioner focus groups are presented, which provided information for CTAP Phase 1, contextual evaluation, surrounding education sector clinicians’ workflows, types of technologies currently available, and influences on technology use. Discussion focuses on how findings will inform subsequent CTAP phases, as well as their implications for future technology adaptation across content domains and service sectors. PMID:25677251

  4. The Contextualized Technology Adaptation Process (CTAP): Optimizing Health Information Technology to Improve Mental Health Systems.

    Science.gov (United States)

    Lyon, Aaron R; Wasse, Jessica Knaster; Ludwig, Kristy; Zachry, Mark; Bruns, Eric J; Unützer, Jürgen; McCauley, Elizabeth

    2016-05-01

    Health information technologies have become a central fixture in the mental healthcare landscape, but few frameworks exist to guide their adaptation to novel settings. This paper introduces the contextualized technology adaptation process (CTAP) and presents data collected during Phase 1 of its application to measurement feedback system development in school mental health. The CTAP is built on models of human-centered design and implementation science and incorporates repeated mixed methods assessments to guide the design of technologies to ensure high compatibility with a destination setting. CTAP phases include: (1) Contextual evaluation, (2) Evaluation of the unadapted technology, (3) Trialing and evaluation of the adapted technology, (4) Refinement and larger-scale implementation, and (5) Sustainment through ongoing evaluation and system revision. Qualitative findings from school-based practitioner focus groups are presented, which provided information for CTAP Phase 1, contextual evaluation, surrounding education sector clinicians' workflows, types of technologies currently available, and influences on technology use. Discussion focuses on how findings will inform subsequent CTAP phases, as well as their implications for future technology adaptation across content domains and service sectors.

  5. Using CASE to Exploit Process Modeling in Technology Transfer

    Science.gov (United States)

    Renz-Olar, Cheryl

    2003-01-01

    A successful business will be one that has processes in place to run that business. Creating processes, reengineering processes, and continually improving processes can be accomplished through extensive modeling. Casewise(R) Corporate Modeler(TM) CASE is a computer aided software engineering tool that will enable the Technology Transfer Department (TT) at NASA Marshall Space Flight Center (MSFC) to capture these abilities. After successful implementation of CASE, it could then go on to be applied in other departments at MSFC and other centers at NASA. The success of a business process is dependent upon the players working as a team and continuously improving the process. A good process fosters customer satisfaction as well as internal satisfaction in the organizational infrastructure. CASE provides a method for business process success through functions consisting of systems and processes business models; specialized diagrams; matrix management; simulation; report generation and publishing; and, linking, importing, and exporting documents and files. The software has an underlying repository or database to support these functions. The Casewise. manual informs us that dynamics modeling is a technique used in business design and analysis. Feedback is used as a tool for the end users and generates different ways of dealing with the process. Feedback on this project resulted from collection of issues through a systems analyst interface approach of interviews with process coordinators and Technical Points of Contact (TPOCs).

  6. Rehabilitation Options

    Science.gov (United States)

    ... Speech Pathology Occupational Therapy Art Therapy Recreational therapy Neuropsychology Home Care Options Advanced Care Planning Palliative Care ... Speech Pathology Occupational Therapy Art Therapy Recreational therapy Neuropsychology Home Care Options Advanced Care Planning Palliative Care ...

  7. Technological and life cycle assessment of organics processing odour control technologies

    International Nuclear Information System (INIS)

    Bindra, Navin; Dubey, Brajesh; Dutta, Animesh

    2015-01-01

    As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

  8. Technological and life cycle assessment of organics processing odour control technologies

    Energy Technology Data Exchange (ETDEWEB)

    Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

    2015-09-15

    As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

  9. Information Technology Process Improvement Decision-Making: An Exploratory Study from the Perspective of Process Owners and Process Managers

    Science.gov (United States)

    Lamp, Sandra A.

    2012-01-01

    There is information available in the literature that discusses information technology (IT) governance and investment decision making from an executive-level perception, yet there is little information available that offers the perspective of process owners and process managers pertaining to their role in IT process improvement and investment…

  10. Database mirroring in fault-tolerant continuous technological process control

    Directory of Open Access Journals (Sweden)

    R. Danel

    2015-10-01

    Full Text Available This paper describes the implementations of mirroring technology of the selected database systems – Microsoft SQL Server, MySQL and Caché. By simulating critical failures the systems behavior and their resilience against failure were tested. The aim was to determine whether the database mirroring is suitable to use in continuous metallurgical processes for ensuring the fault-tolerant solution at affordable cost. The present day database systems are characterized by high robustness and are resistant to sudden system failure. Database mirroring technologies are reliable and even low-budget projects can be provided with a decent fault-tolerant solution. The database system technologies available for low-budget projects are not suitable for use in real-time systems.

  11. IMPROVING THE QUALITY OF MAINTENANCE PROCESSES USING INFORMATION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Zora Arsovski

    2008-06-01

    Full Text Available In essence, process of maintaining equipment is a support process, because it indirectly contributes to operational ability of the production process necessary for the supply chain of the new value. Taking into account increased levels of automatization and quality, this proces s becomes more and more significant and for some branches of industry, even crucial. Due to the fact that the quality of the entire process is more and more dependent on the maintenance process, these processes must be carefully designed and effectively im plemented. There are various techniques and approaches at our disposal, such as technical, logistical and intensive application of the information - communication technologies. This last approach is presented in this work. It begins with organizational goa ls, especially quality objectives. Then, maintenance processes and integrated information system structures are defined. Maintenance process quality and improvement processes are defined using a set of performances, with a special emphasis placed on effectiveness and quality economics. At the end of the work, information system for improving maintenance economics is structured. Besides theoretical analysis, work also presents results authors obtained analyzing food industry, metal processing industry an d building materials industry.

  12. Technology Roadmap: Energy and GHG reductions in the chemical industry via catalytic processes

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-01

    The chemical industry is a large energy user; but chemical products and technologies also are used in a wide array of energy saving and/or renewable energy applications so the industry has also an energy saving role. The chemical and petrochemical sector is by far the largest industrial energy user, accounting for roughly 10% of total worldwide final energy demand and 7% of global GHG emissions. The International Council of Chemical Associations (ICCA) has partnered with the IEA and DECHEMA (Society for Chemical Engineering and Biotechnology) to describe the path toward further improvements in energy efficiency and GHG reductions in the chemical sector. The roadmap looks at measures needed from the chemical industry, policymakers, investors and academia to press on with catalysis technology and unleash its potential around the globe. The report uncovers findings and best practice opportunities that illustrate how continuous improvements and breakthrough technology options can cut energy use and bring down greenhouse gas (GHG) emission rates. Around 90% of chemical processes involve the use of catalysts – such as added substances that increase the rate of reaction without being consumed by it – and related processes to enhance production efficiency and reduce energy use, thereby curtailing GHG emission levels. This work shows an energy savings potential approaching 13 exajoules (EJ) by 2050 – equivalent to the current annual primary energy use of Germany.

  13. Designing Robust Process Analytical Technology (PAT) Systems for Crystallization Processes: A Potassium Dichromate Crystallization Case Study

    DEFF Research Database (Denmark)

    Abdul Samad, Noor Asma Fazli Bin; Sin, Gürkan

    2013-01-01

    The objective of this study is to test and validate a Process Analytical Technology (PAT) system design on a potassium dichromate crystallization process in the presence of input uncertainties using uncertainty and sensitivity analysis. To this end a systematic framework for managing uncertaintie...

  14. Process of technology management in SMEs of the metal processing industry – the case study investigation

    Directory of Open Access Journals (Sweden)

    Krawczyk-Dembicka Elżbieta

    2017-03-01

    Full Text Available The main purpose of this work is to identify the factors that influence the process of technology management in the sector of small- and medium-sized enterprises of the metal processing industry, considering the shape and course required to achieve modern operation conditions by enterprises in the market.

  15. Role of health-keeping technologies in educational process

    Directory of Open Access Journals (Sweden)

    Voloshin O. R.

    2012-07-01

    Full Text Available The value of health-keeping technologies in educational process is considered. Theoretical methodological approaches of their interpretation are exposed. The making forming for the man of conscious motivation in relation to the maintainance of individual health is shown. Valeological and ecological values are analysed. The features of introduction of health-keeping technologies in a modern educational process are certain. The complex estimation of terms of education and studies, which allow to provide the good state of health of young people, care of high level of their self-realization, skills of healthy way of life, is resulted, to carry out monitoring of indexes of individual development, forecast the possible changes of health. It is marked on the necessity of providing of harmonious development of natural capabilities of personality: its mind, moral and aesthetically beautiful senses, requirement in activity, capture initial experience of socializing with people.

  16. Current mechanisms in silicon PIN structures processed with various technologies

    CERN Document Server

    Ruzin, A

    2002-01-01

    This study presents a comparison of dark characteristics of PIN (p sup + -semi-intrinsic-n sup +) structures fabricated with several technologies on high-resistivity silicon wafers. The study considers the temperature dependence of the various current mechanisms. Significant and consistent differences were observed in the reverse current-voltage characteristics of the various samples, while capacitance-voltage profiles remain similar, indicating no process related variations in the effective space charge distribution. The results show that the activation energy of the reverse current in samples processed by various technologies differs, which may indicate that the Shockley Read Hall generation occurs through centers at different energies. Specifically, in some samples the reverse currents are dominated by generation-recombination centers located approx 0.2 eV from the mid-gap, while in other samples the currents are dominated by the 'standard' mid-gap generation-recombination centers. The difference is shown ...

  17. The evolution of waste management processes and technologies in BNFL

    International Nuclear Information System (INIS)

    Asquith, R.W.; Fairhall, G.A.

    1997-01-01

    The treatment of wastes arising from BNFL''s nuclear fuel cycle operations can be traced through a number of phases. The first was the development of vitrification and cementation for fresh arisings. Plants utilising these technologies are now in operation. To handle the mixed, heterogeneous intermediate level wastes, retrieval, segregation and robust treatment processes are at an advanced stage of development, with all plants to be operational from 2002. BNFL is focusing attention on reducing waste management lifetime costs including reducing waste volumes of source. Technologies aimed at significant reductions are now being developed. The final phase, now in progress, recognizes the need for an integrated approach to advanced fuel cycle processes which incorporates BNFL''s holistic concept. (author)

  18. The Aluminum Smelting Process and Innovative Alternative Technologies

    Science.gov (United States)

    Drabløs, Per Arne

    2014-01-01

    Objective: The industrial aluminum production process is addressed. The purpose is to give a short but comprehensive description of the electrolysis cell technology, the raw materials used, and the health and safety relevance of the process. Methods: This article is based on a study of the extensive chemical and medical literature on primary aluminum production. Results: At present, there are two main technological challenges for the process—to reduce energy consumption and to mitigate greenhouse gas emissions. A future step may be carbon dioxide gas capture and sequestration related to the electric power generation from fossil sources. Conclusions: Workers' health and safety have now become an integrated part of the aluminum business. Work-related injuries and illnesses are preventable, and the ultimate goal to eliminate accidents with lost-time injuries may hopefully be approached in the future. PMID:24806723

  19. Waste Not, Want Not: Analyzing the Economic and Environmental Viability of Waste-to-Energy (WTE) Technology for Site-Specific Optimization of Renewable Energy Options

    Energy Technology Data Exchange (ETDEWEB)

    Funk, K.; Milford, J.; Simpkins, T.

    2013-02-01

    Waste-to-energy (WTE) technology burns municipal solid waste (MSW) in an environmentally safe combustion system to generate electricity, provide district heat, and reduce the need for landfill disposal. While this technology has gained acceptance in Europe, it has yet to be commonly recognized as an option in the United States. Section 1 of this report provides an overview of WTE as a renewable energy technology and describes a high-level model developed to assess the feasibility of WTE at a site. Section 2 reviews results from previous life cycle assessment (LCA) studies of WTE, and then uses an LCA inventory tool to perform a screening-level analysis of cost, net energy production, greenhouse gas (GHG) emissions, and conventional air pollution impacts of WTE for residual MSW in Boulder, Colorado. Section 3 of this report describes the federal regulations that govern the permitting, monitoring, and operating practices of MSW combustors and provides emissions limits for WTE projects.

  20. Studies on Separation Process and Production Technology of Boron Isotope

    OpenAIRE

    LI Jian-ping

    2014-01-01

    The boron isotopes separation test was performed by chemical exchange reaction in the benzene ether -three boron fluoride system, which resulted to the boron isotopic enrichment of -10 in the liquid phase, the boron isotopic enrichment of -11 in the gas phase. After then, boron isotope separation trial production has been finished. In this process, the exchange column and complex tower normal operating parameters and the complex tower technology have been obtained, the problems of material di...

  1. Surviving security how to integrate people, process, and technology

    CERN Document Server

    Andress, Amanda

    2003-01-01

    WHY DO I NEED SECURITY? Introduction The Importance of an Effective Security Infrastructure People, Process, and Technology What Are You Protecting Against? Types of Attacks Types of Attackers Security as a Competitive Advantage Choosing a Solution Finding Security Employees The Layered Approach UNDERSTANDING REQUIREMENTS AND RISK What Is Risk? Embracing Risk Information Security Risk Assessment Assessing Risk Insurance SECURITY POLICIES AND PROCEDURES Internal Focus Is Key Security Awareness and Education Policy Life Cycle Developing Policies Components of a Security Policy Sample Security Po

  2. Lignocellulosic ethanol: Technology design and its impact on process efficiency.

    Science.gov (United States)

    Paulova, Leona; Patakova, Petra; Branska, Barbora; Rychtera, Mojmir; Melzoch, Karel

    2015-11-01

    This review provides current information on the production of ethanol from lignocellulosic biomass, with the main focus on relationships between process design and efficiency, expressed as ethanol concentration, yield and productivity. In spite of unquestionable advantages of lignocellulosic biomass as a feedstock for ethanol production (availability, price, non-competitiveness with food, waste material), many technological bottlenecks hinder its wide industrial application and competitiveness with 1st generation ethanol production. Among the main technological challenges are the recalcitrant structure of the material, and thus the need for extensive pretreatment (usually physico-chemical followed by enzymatic hydrolysis) to yield fermentable sugars, and a relatively low concentration of monosaccharides in the medium that hinder the achievement of ethanol concentrations comparable with those obtained using 1st generation feedstocks (e.g. corn or molasses). The presence of both pentose and hexose sugars in the fermentation broth, the price of cellulolytic enzymes, and the presence of toxic compounds that can inhibit cellulolytic enzymes and microbial producers of ethanol are major issues. In this review, different process configurations of the main technological steps (enzymatic hydrolysis, fermentation of hexose/and or pentose sugars) are discussed and their efficiencies are compared. The main features, benefits and drawbacks of simultaneous saccharification and fermentation (SSF), simultaneous saccharification and fermentation with delayed inoculation (dSSF), consolidated bioprocesses (CBP) combining production of cellulolytic enzymes, hydrolysis of biomass and fermentation into one step, together with an approach combining utilization of both pentose and hexose sugars are discussed and compared with separate hydrolysis and fermentation (SHF) processes. The impact of individual technological steps on final process efficiency is emphasized and the potential for use

  3. Army Information Technology Procurement: A Business Process Analysis

    Science.gov (United States)

    2015-03-27

    Education and Training Command In Partial Fulfillment of the Requirements for the Degree of Master of Science in Engineering Management...Brent Langhals, Lt Col, USAF Member John Elshaw, PhD Member Abstract The integration of Information and Communication Technology ( ICT ...the lack transparency in how resources are allocated. This thesis presents a business process analysis of the Army’s ICT procurement system. The

  4. Industrial Maturity of FR Fuel Cycle Processes and Technologies

    International Nuclear Information System (INIS)

    Bruezière, Jérôme

    2013-01-01

    FR fuel cycle processes and technologies have already been proven industrially for Oxide Fuel, and to a lesser extent for metal fuel. In addition, both used oxide fuel reprocessing and fresh oxide fuel manufacturing benefit from similar industrial experience currently deployed for LWR. Alternative fuel type will have to generate very significant benefit in reactor ( safety, cost, … ) to justify corresponding development and industrialization costs

  5. Effectiveness of Information Technology Infrastructure Library Process Implementations by Information Technology Departments within United States Organizations

    Science.gov (United States)

    Persinger, Jon F.

    2010-01-01

    This research study examined whether the overall effectiveness of the Information Technology Infrastructure Library (ITIL) could be predicted by measuring multiple independent variables. The primary variables studied included the number of ITIL process modules adopted and the overall ITIL "maturity level." An online survey was used to…

  6. Technology and plasma-materials interaction processes of tokamak disruptions

    International Nuclear Information System (INIS)

    McGrath, R.T.; Kellman, A.G.

    1992-01-01

    A workshop on the technology and plasma-materials interaction processes of tokamak disruptions was held April 3, 1992 in Monterey, California, as a satellite meeting of the 10th International Conference on Plasma-Surface Interactions. The objective was to bring together researchers working on disruption measurements in operating tokamaks, those performing disruption simulation experiments using pulsed plasma gun, electron beam and laser systems, and computational physicists attempting to model the evolution and plasma-materials interaction processes of tokamak disruptions. This is a brief report on the workshop. 4 refs

  7. Centralisation of informatics (more effective processes via using new technologies)

    International Nuclear Information System (INIS)

    Cocher, L.

    2004-01-01

    In this presentation author deals with next problems of Slovenske elektrarne, Plc (SE): - Centralisation and optimisation of informatics management; - New technologies within Integrated Informatics System IIS-SE: presentation of preliminary Project of 2 nd generation IIS-SE; - Centralisation of the selected data processing. At the present the intensive process of restructuring is taking place in SE, Plc, focused on increasing of the effectiveness of the pursued activities. In connection with this the Informatics section solves two projects: More effective self-management and human resources; Change of Informatics system architecture from decentralised to the centralised ones with an aim to consolidate all information and to make new conditions for higher mobility

  8. Computer-Aided Modeling of Lipid Processing Technology

    DEFF Research Database (Denmark)

    Diaz Tovar, Carlos Axel

    2011-01-01

    increase along with growing interest in biofuels, the oleochemical industry faces in the upcoming years major challenges in terms of design and development of better products and more sustainable processes to make them. Computer-aided methods and tools for process synthesis, modeling and simulation...... are widely used for design, analysis, and optimization of processes in the chemical and petrochemical industries. These computer-aided tools have helped the chemical industry to evolve beyond commodities toward specialty chemicals and ‘consumer oriented chemicals based products’. Unfortunately...... to develop systematic computer-aided methods (property models) and tools (database) related to the prediction of the necessary physical properties suitable for design and analysis of processes employing lipid technologies. The methods and tools include: the development of a lipid-database (CAPEC...

  9. Materials, process, product analysis of coal process technology. Phase I final report

    Energy Technology Data Exchange (ETDEWEB)

    Saxton, J. C.; Roig, R. W.; Loridan, A.; Leggett, N. E.; Capell, R. G.; Humpstone, C. C.; Mudry, R. N.; Ayres, E.

    1976-02-01

    The purpose of materials-process-product analysis is a systematic evaluation of alternative manufacturing processes--in this case processes for converting coal into energy and material products that can supplement or replace petroleum-based products. The methodological steps in the analysis include: Definition of functional operations that enter into coal conversion processes, and modeling of alternative, competing methods to accomplish these functions; compilation of all feasible conversion processes that can be assembled from combinations of competing methods for the functional operations; systematic, iterative evaluation of all feasible conversion processes under a variety of economic situations, environmental constraints, and projected technological advances; and aggregative assessments (economic and environmental) of various industrial development scenarios. An integral part of the present project is additional development of the existing computer model to include: A data base for coal-related materials and coal conversion processes; and an algorithmic structure that facilitates the iterative, systematic evaluations in response to exogenously specified variables, such as tax policy, environmental limitations, and changes in process technology and costs. As an analytical tool, the analysis is intended to satisfy the needs of an analyst working at the process selection level, for example, with respect to the allocation of RDandD funds to competing technologies.

  10. Evaluation of prospective hazardous waste treatment technologies for use in processing low-level mixed wastes at Rocky Flats

    International Nuclear Information System (INIS)

    McGlochlin, S.C.; Harder, R.V.; Jensen, R.T.; Pettis, S.A.; Roggenthen, D.K.

    1990-01-01

    Several technologies for destroying or decontaminating hazardous wastes were evaluated (during early 1988) as potential processes for treating low-level mixed wastes destined for destruction in the Fluidized Bed Incinerator. The processes that showed promise were retained for further consideration and placed into one (or more) of three categories based on projected availability: short, intermediate, and long-term. Three potential short-term options were identified for managing low-level mixed wastes generated or stored at the Rocky Flats Plant (operated by Rockwell International in 1988). These options are: (1) Continue storing at Rocky Flats, (2) Ship to Nevada Test Site for landfill disposal, or (3) Ship to the Idaho National Engineering Laboratory for incineration in the Waste Experimental Reduction Facility. The third option is preferable because the wastes will be destroyed. Idaho National Engineering Laboratory has received interim status for processing solid and liquid low-level mixed wastes. However, low-level mixed wastes will continue to be stored at Rocky Flats until the Department of Energy approval is received to ship to the Nevada Test Site or Idaho National Engineering Laboratory. Potential intermediate and long-term processes were identified; however, these processes should be combined into complete waste treatment ''systems'' that may serve as alternatives to the Fluidized Bed Incinerator. Waste treatment systems will be the subject of later work. 59 refs., 2 figs

  11. The review of recent carbonate minerals processing technology

    Science.gov (United States)

    Solihin

    2018-02-01

    Carbonate is one of the groups of minerals that can be found in relatively large amount in the earth crust. The common carbonate minerals are calcium carbonate (calcite, aragonite, depending on its crystal structure), magnesium carbonate (magnesite), calcium-magnesium carbonate (dolomite), and barium carbonate (barite). A large amount of calcite can be found in many places in Indonesia such as Padalarang, Sukabumi, and Tasikmalaya (West Java Provence). Dolomite can be found in a large amount in Gresik, Lamongan, and Tuban (East Java Provence). Magnesite is quite rare in Indonesia, and up to the recent years it can only be found in Padamarang Island (South East Sulawesi Provence). The carbonate has been being exploited through open pit mining activity. Traditionally, calcite can be ground to produce material for brick production, be carved to produce craft product, or be roasted to produce lime for many applications such as raw materials for cement, flux for metal smelting, etc. Meanwhile, dolomite has traditionally been used as a raw material to make brick for local buildings and to make fertilizer for coconut oil plant. Carbonate minerals actually consist of important elements needed by modern application. Calcium is one of the elements needed in artificial bone formation, slow release fertilizer synthesis, dielectric material production, etc. Magnesium is an important material in automotive industry to produce the alloy for vehicle main parts. It is also used as alloying element in the production of special steel for special purpose. Magnesium oxide can be used to produce slow release fertilizer, catalyst and any other modern applications. The aim of this review article is to present in brief the recent technology in processing carbonate minerals. This review covers both the technology that has been industrially proven and the technology that is still in research and development stage. One of the industrially proven technologies to process carbonate mineral is

  12. Role of BRIT in promoting radiation processing technology in India

    International Nuclear Information System (INIS)

    Bandi, L.N.

    2014-01-01

    Some of the major applications of radiation processing include: the sterilization of products such as medical devices to kill bacteria or in the case of food, hygienize the product; the treatment of export bulk commodities such as tropical fruits to extend shelf life by slowing the ripening process and inhibiting sprouting and to kill quarantine pests such as fruit flies. Radiation processing is a value addition process. Taking note of these benefits, Department of Atomic Energy, Government of India constituted Board of Radiation and Isotope Technology (BRIT) in March 1989 by carving it out from Bhabha Atomic Research Centre, Mumbai. The mandate given to BRIT was to extend commercial applications of radioisotopes and radiation in the areas of Health, Agriculture, Industry and Research without losing sight of societal obligations. So far Department of Atomic Energy has set up three demonstration plants, namely, Isomed, RPP, Vashi and Krushak for high, medium and low dose applications of radiation respectively. The safe and business like operation of these facilities amply demonstrated the embedded safety and commercial viability of this technology

  13. New radiation technologies and methods for control of technological processes in metallurgy

    International Nuclear Information System (INIS)

    Zaykin, Yu.

    1996-01-01

    Radiation Technology of Metal and Ceramic Production with Enhanced Service Properties. Based on application of radiation technique in powder metallurgy the new technology for obtaining metals, alloys and ceramic materials with high service properties is worked out. Radiation processing of powder materials at the certain stage of the process leads to profound structure alterations at all further stages and eventually effects the properties of the resulting product. Theoretical calculation and experimental studies of electron-positron annihilation in powder-pressed samples showed that irradiation caused powder particles surface state changes favorable for further sintering and crystallization processes development. It is shown that irradiation of metal powders and powder-pressed samples by high energy electrons is technologically most efficient. The right choice of the type-and the mode of the radiation processing makes it possible to obtain metals, alloys and ceramic materials (Mo,Fe, W, Al, Ni, Cu, stainless steels, ceramics, etc.) with homogeneous structure and stable enhanced service properties. The project on radiation technology application to powder metallurgy represented by a group of authors was awarded with the diploma and the gold medal at the 22 International Exhibition of Inventions (Geneva, 1994). New Technologic Opportunities of the Chromium-Nickel Alloys Processing To obtain the required phase-structure state special methods of the chromium-nickel alloy processing for sensitive elastic devices production were worked out combining plastic deformation, thermal and radiation processing. It is shown that h-gbb phase transfer not observed before is possible in extremely non-equilibrium conditions under electron irradiation. It is established that the complex reaction of recrystallization and gb-phase deposition proceeds under electron irradiation at the room temperature when the certain threshold plastic deformation degree is reached that leads to the same

  14. Evaluation of Brine Processing Technologies for Spacecraft Wastewater

    Science.gov (United States)

    Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie; hide

    2015-01-01

    Brine drying systems may be used in spaceflight. There are several advantages to using brine processing technologies for long-duration human missions including a reduction in resupply requirements and achieving high water recovery ratios. The objective of this project was to evaluate four technologies for the drying of spacecraft water recycling system brine byproducts. The technologies tested were NASA's Forward Osmosis Brine Drying (FOBD), Paragon's Ionomer Water Processor (IWP), NASA's Brine Evaporation Bag (BEB) System, and UMPQUA's Ultrasonic Brine Dewatering System (UBDS). The purpose of this work was to evaluate the hardware using feed streams composed of brines similar to those generated on board the International Space Station (ISS) and future exploration missions. The brine formulations used for testing were the ISS Alternate Pretreatment and Solution 2 (Alt Pretreat). The brines were generated using the Wiped-film Rotating-disk (WFRD) evaporator, which is a vapor compression distillation system that is used to simulate the function of the ISS Urine Processor Assembly (UPA). Each system was evaluated based on the results from testing and Equivalent System Mass (ESM) calculations. A Quality Function Deployment (QFD) matrix was also developed as a method to compare the different technologies based on customer and engineering requirements.

  15. Layers And Processes In The Model Of Technological Postal System

    Directory of Open Access Journals (Sweden)

    Madleňáková Lucia

    2015-12-01

    Full Text Available The paper include important aspects of layer model of postal technological system such as makes the possibility to define rules for regulating, technical and technological requirements and interfaces to communicate with other postal systems. The current postal reform is mainly attributable to release of network access and ensuring full interoperability between technological systems. Not only to ensure the development and protection of competition but also in respect to the conservation of requirements to provide the universal service, which is the performance of public interest. There is a space here to examine the postal system, not only from a procedural point of view, but to be viewed as an open communication system. It is possible to find there the commonalities with other communication sector branches and to handle the technological postal system in more layers; similarly as the electronic communication systems are handled. Model of layer postal system, based not only on the processes but on layers functionality, will enable to identify communication protocols and interfaces determining interoperability. It also opens the question of appropriate regulation model.

  16. Advanced modeling of management processes in information technology

    CERN Document Server

    Kowalczuk, Zdzislaw

    2014-01-01

    This book deals with the issues of modelling management processes of information technology and IT projects while its core is the model of information technology management and its component models (contextual, local) describing initial processing and the maturity capsule as well as a decision-making system represented by a multi-level sequential model of IT technology selection, which acquires a fuzzy rule-based implementation in this work. In terms of applicability, this work may also be useful for diagnosing applicability of IT standards in evaluation of IT organizations. The results of this diagnosis might prove valid for those preparing new standards so that – apart from their own visions – they could, to an even greater extent, take into account the capabilities and needs of the leaders of project and manufacturing teams. The book is intended for IT professionals using the ITIL, COBIT and TOGAF standards in their work. Students of computer science and management who are interested in the issue of IT...

  17. HEALTH TECHNOLOGY ASSESSMENT, DELIBERATIVE PROCESS, AND ETHICALLY CONTESTED ISSUES.

    Science.gov (United States)

    Daniels, Norman; van der Wilt, Gert Jan

    2016-01-01

    Healthcare technology assessment (HTA) aims to support decisions as to which technologies should be used in which situations to optimize value. Because such decisions will create winners and losers, they are bound to be controversial. HTA, then, faces a dilemma: should it stay away from such controversies, remaining a source of incomplete advice and risking an important kind of marginalization, or should it enter the controversy? The question is a challenging one, because we lack agreement on principles that are fine grained enough to tell us what choices we should make. In this study, we will argue that HTA should take a stand on ethical issues raised by the technology that is being investigated. To do so, we propose adding a form of procedural justice to HTA to arrive at decisions that the public can regard as legitimate and fair. A fair process involves deliberation about the reasons, evidence, and rationales that are considered relevant to meeting population-health needs fairly. One important way to make sure that there is real deliberation about relevant reasons is to include a range of stakeholders in the deliberative process. To illustrate how such deliberation might work, we use the case of cochlear implants for deaf children.

  18. Option Pricing with a Levy-Type Stochastic Dynamic Model for Stock Price Process Under Semi-Markovian Structural Perturbations

    Science.gov (United States)

    2015-11-30

    its implications for option pricing, The Journal of Finance 35 (3), 661–673. F. Black & M. Scholes (1973) The pricing of options and corporate ...Note © 2015 . Published in INTERNATIONAL JOURNAL OF THEORETICAL AND APPLIED FINANCE , Vol. Ed. 0 18, (8) (2015), (, (8). DoD Components reserve a...S0219-0249 104-IJTAF SPI-J071 1550052 International Journal of Theoretical and Applied Finance Vol. 18, No. 8 (2015) 1550052 (72 pages) c© World

  19. A combinaison of UV curing technology with ATL process

    Science.gov (United States)

    Balbzioui, I.; Hasiaoui, B.; Barbier, G.; L'hostis, G.; Laurent, F.; Ibrahim, A.; Durand, B.

    2017-10-01

    In order to reduce the time and the cost of manufacturing composite, UV curing technology combined with automated tape placement process (ATL) based on reverse approach by working with a fixed head was studied in this article. First, a brief description of the developed head placement is presented. Mechanical properties are then evaluated by varying process parameters, including compaction force and tape placement speed. Finally, a parametric study is carried out to identify suitable materials and process parameters to manufacture a photo composite material with high mechanical performances. The obtained results show that UV curing is a very good alternative for thermal polymerization because of its fast cure speed due to less dependency on temperature.

  20. Actinide solution processing at the Rocky Flats Environmental Technology Site

    International Nuclear Information System (INIS)

    1995-04-01

    The Department of Energy (DOE) has prepared an Environmental Assessment (EA), DOE/EA-1039, for radioactive solution removal and processing at Rocky Flats Environmental Technology Site, Golden, Colorado. The proposal for solution removal and processing is in response to independent safety assessments and an agreement with the State of Colorado to remove mixed residues at Rocky Flats and reduce the risk of future accidents. Monthly public meetings were held during the scoping and preparation of the EA. The scope of the EA included evaluations of alternative methods and locations of solution processing. A comment period from February 20, 1995 through March 21, 1995 was provided to the public and the State of Colorado to offer written comment on the EA. Comments were received from the State of Colorado and the U.S. Environmental Protection Agency. A response to the agency comments is included in the Final EA

  1. Evaluation of energy efficiency options in steam assisted gravity drainage oil sands surface facilities via process integration

    International Nuclear Information System (INIS)

    Carreon, Carlos E.; Mahmoudkhani, Maryam; Alva-Argaez, Alberto; Bergerson, Joule

    2015-01-01

    While new technologies are being developed for extracting unconventional oil, in the near term economic benefits and footprint reduction can be achieved by enhancing the energy efficiency of existing facilities. The objective of this work is to evaluate energy efficiency opportunities for in situ extraction of Canada's oil sands resource using pinch analysis. Modifications to an original plant design are analyzed in order to estimate utility savings beyond those obtained for the initial process configuration. The modifications explored in this paper are estimated to deliver energy savings of up to 6% beyond ‘business as usual’. This corresponds to GHG emissions reduction of approximately 5%. However, in some cases, this increase in energy savings comes at the cost of increasing demand for make-up water and volume of disposal water. Surplus generation of steam beyond heating requirements in the water treatment system leads to energy inefficiencies. Additional cost and energy savings are obtained by reducing or eliminating the use of glycol in the cooling circuit. - Highlights: • Pinch analysis performed for unconventional oil recovery process to identify inefficiencies. • Both the removal of pinch violations and process modifications lead to savings. • Effect of energy savings on water consumption for the process is considered. • Greenhouse gas emissions reduction and economic benefit are estimated for the studied cases

  2. Commentary: how can technology help us understand the communication process?

    Science.gov (United States)

    Keyton, Joann

    2012-08-01

    In this commentary, the author reflects on the articles chosen for the special section on communications analysis. These articles problematize communication and raise an interesting set of questions for both human factors and communication scholars to ponder. In the end, both sets of scholars seek the same goal: How do we better examine communication to improve it? Problematizing communication requires scholars to challenge their fundamental assumptions about the phenomenon as well as to tease out the distinctions of methodological approaches typically used by both human factors and communication scholars. Human factors scholars tend to favor forms of communication in which technology or task roles control who can communicate and how. Communication scholars tend to favor contexts in which information flows more freely with fewer explicit restrictions. Creating opportunities to collaborate in research on the communication process may create the best understanding of technology that can better serve our understanding of communication.

  3. Technological Innovation: Concept, Process, Typology and Implications in the Economy

    Directory of Open Access Journals (Sweden)

    Mihaela DIACONU

    2011-10-01

    Full Text Available Growing interest worldwide to boost innovation in business sector activities, especially the technology, is intended to maintain or increase national economic competitiveness, inclusively as an effect of awareness concerning the effects resulting from economic activity on consumption of resources and environment, which requires design of new patterns of production and consumption. In this paper we review the most important contributions in the literature in terms of the implications of technological innovation in the economy, at the microand macroeconomic level, viewing the organization's ability to generate new ideas in support of increasing production, employment and environmental protection, starting from the concepts of innovation, innovation process and, respectively, from the innovation typology analysis.

  4. Nuclear reactor fuel cycle technology with pyroelectrochemical processes

    International Nuclear Information System (INIS)

    Skiba, O.V.; Maershin, A.A.; Bychkov, A.V.; Zhdanov, A.N.; Kislyj, V.A.; Vavilov, S.K.; Babikov, L.G.

    1999-01-01

    A group of dry technologies and processes of vibro-packing granulated fuel in combination with unique properties of vibro-packed FEs make it possible to implement a new comprehensive approach to the fuel cycle with plutonium fuel. Testing of a big number of FEs with vibro-packed U-Pu oxide fuel in the BOR-60 reactor, successful testing of experimental FSAs in the BN-600 rector, reliable operation of the experimental and research complex facilities allow to make the conclusion about a real possibility to develop a safe, economically beneficial U-Pu fuel cycle based on the technologies enumerated above and to use both reactor-grade and weapon-grade plutonium in nuclear reactors with a reliable control and accounting system [ru

  5. Technical and economic assessment of processes for the production of butanol and acetone. Phase two: analysis of research advances. Energy Conversion and Utilization Technologies Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-08-01

    The initial objective of this work was to develop a methodology for analyzing the impact of technological advances as a tool to help establish priorities for R and D options in the field of biocatalysis. As an example of a biocatalyzed process, butanol/acetone fermentation (ABE process) was selected as the specific topic of study. A base case model characterizing the technology and economics associated with the ABE process was developed in the previous first phase of study. The project objectives were broadened in this second phase of work to provide parametric estimates of the economic and energy impacts of a variety of research advances in the hydrolysis, fermentation and purification sections of the process. The research advances analyzed in this study were based on a comprehensive literature review. The six process options analyzed were: continuous ABE fermentaton; vacuum ABE fermentation; Baelene solvent extraction; HRI's Lignol process; improved prehydrolysis/dual enzyme hydrolysis; and improved microorganism tolerance to butanol toxicity. Of the six options analyzed, only improved microorganism tolerance to butanol toxicity had a significant positive effect on energy efficiency and economics. This particular process option reduced the base case production cost (including 10% DCF return) by 20% and energy consumption by 16%. Figures and tables.

  6. Missile signal processing common computer architecture for rapid technology upgrade

    Science.gov (United States)

    Rabinkin, Daniel V.; Rutledge, Edward; Monticciolo, Paul

    2004-10-01

    Interceptor missiles process IR images to locate an intended target and guide the interceptor towards it. Signal processing requirements have increased as the sensor bandwidth increases and interceptors operate against more sophisticated targets. A typical interceptor signal processing chain is comprised of two parts. Front-end video processing operates on all pixels of the image and performs such operations as non-uniformity correction (NUC), image stabilization, frame integration and detection. Back-end target processing, which tracks and classifies targets detected in the image, performs such algorithms as Kalman tracking, spectral feature extraction and target discrimination. In the past, video processing was implemented using ASIC components or FPGAs because computation requirements exceeded the throughput of general-purpose processors. Target processing was performed using hybrid architectures that included ASICs, DSPs and general-purpose processors. The resulting systems tended to be function-specific, and required custom software development. They were developed using non-integrated toolsets and test equipment was developed along with the processor platform. The lifespan of a system utilizing the signal processing platform often spans decades, while the specialized nature of processor hardware and software makes it difficult and costly to upgrade. As a result, the signal processing systems often run on outdated technology, algorithms are difficult to update, and system effectiveness is impaired by the inability to rapidly respond to new threats. A new design approach is made possible three developments; Moore's Law - driven improvement in computational throughput; a newly introduced vector computing capability in general purpose processors; and a modern set of open interface software standards. Today's multiprocessor commercial-off-the-shelf (COTS) platforms have sufficient throughput to support interceptor signal processing requirements. This application

  7. Trapping technology for gaseous fission products from voloxidation process

    International Nuclear Information System (INIS)

    Shin, Jin Myeong; Park, J. J.; Park, G. I.; Jung, I. H.; Lee, H. H.; Kim, G. H.; Yang, M. S.

    2005-05-01

    The objective of this report is to review the different technologies for trapping the gaseous wastes containing Cs, Ru, Tc, 14 C, Kr, Xe, I and 3 H from a voloxidation process. Based on literature reviews and KAERI's experimental results on the gaseous fission products trapping, appropriate trapping method for each fission product has been selected considering process reliability, simplicity, decontamination factor, availability, and disposal. Specifically, the most promising trapping method for each fission product has been proposed for the development of the INL off-gas trapping system. A fly ash filter is proposed as a trapping media for a cesium trapping unit. In addition, a calcium filter is proposed as a trapping media for ruthenium, technetium, and 14 C trapping unit. In case of I trapping unit, AgX is proposed. For Kr and Xe, adsorption on solid is proposed. SDBC (Styrene Divinyl Benzene Copolymer) is also proposed as a conversion media to HTO for 3 H. This report will be used as a useful means for analyzing the known trapping technologies and help selecting the appropriate trapping methods for trapping volatile and semi-volatile fission products, long-lived fission products, and major heat sources generated from a voloxidation process. It can also be used to design an off-gas treatment system

  8. A Benchmark Approach of Counterparty Credit Exposure of Bermudan Option under Lévy Process : The Monte Carlo-COS Method

    NARCIS (Netherlands)

    Shen, Y.; Van der Weide, J.A.M.; Anderluh, J.H.M.

    2013-01-01

    An advanced method, which we call Monte Carlo-COS method, is proposed for computing the counterparty credit exposure profile of Bermudan options under Lévy process. The different exposure profiles and exercise intensity under different mea- sures, P and Q, are discussed. Since the COS method [1

  9. Staging Co-design Processes for Self-care Technologies

    DEFF Research Database (Denmark)

    Brodersen, Søsser Grith Kragh; Lindegaard, Hanne

    2016-01-01

    field studies in people’s homes and discuss how to stage design processes with the people who are actually going to use the self-care technologies—not only end-users, but also many other actors, such as relatives, caregivers, and municipality and company staff. Specifically, we describe how challenges......Many new healthcare technologies are currently being implemented in people’s homes in order to facilitate self-care. Socially innovative design is challenging, since it requires an intimate understanding of people’s abilities and daily practices. In this article, we highlight the need to perform...

  10. Instrument maintenance of ultrasonic influences parameters measurement in technological processes

    Directory of Open Access Journals (Sweden)

    Tomal V. S.

    2008-04-01

    Full Text Available The contact and non-contact vibration meters for intermittent and continuous control of the vibration amplitude in the ultrasonic technological equipment have been developed. And in order to estimate the cavitation intensity in liquids the authors have developed cavitation activity indicators and cavitation sensitivity meters, allowing to measure the magnitude of the signal level in the range of maximum spectral density of cavitation noise. The developed instruments allow to improve the quality of products, reduce the defect rate and power consumption of equipment by maintaining optimum conditions of the process.

  11. The processing technology of bread crumbs sterilization by irradiation

    International Nuclear Information System (INIS)

    Zhu Jiating; Li Zhengkui; Zhao Yongfu; Zhang Weidong; Jin Jie; Wu Lei; Wang Xinghai

    2003-01-01

    The processing technology of bread crumbs sterilization by irradiation was studied. The results demonstrated that dose heterogeneity had osculatory connection with pile height and turning, sterilization effect had positive correlation with the irradiation dose and negative correlation with colour. Compared with the CK, the content of crud protein, fat, carbohydrate, microelement and amino acid in irradiated bread crumbs had no obvious change. It is recommended that the range of best sterilization dose be 6-10 kGy and the shelf time of bread crumbs be extended to one year

  12. Identification of Response Options to Artisanal and Small-Scale Gold Mining (ASGM) in Ghana via the Delphi Process.

    Science.gov (United States)

    Basu, Avik; Phipps, Sean; Long, Rachel; Essegbey, George; Basu, Niladri

    2015-09-10

    The Delphi technique is a means of facilitating discussion among experts in order to develop consensus, and can be used for policy formulation. This article describes a modified Delphi approach in which 27 multi-disciplinary academics and 22 stakeholders from Ghana and North America were polled about ways to address negative effects of small-scale gold mining (ASGM) in Ghana. In early 2014, the academics, working in disciplinary groups, synthesized 17 response options based on data aggregated during an Integrated Assessment of ASGM in Ghana. The researchers participated in two rounds of Delphi polling in March and April 2014, during which 17 options were condensed into 12. Response options were rated via a 4-point Likert scale in terms of benefit (economic, environmental, and benefit to people) and feasibility (economic, social/cultural, political, and implementation). The six highest-scoring options populated a third Delphi poll, which 22 stakeholders from diverse sectors completed in April 2015. The academics and stakeholders also prioritized the response options using ranking exercises. The technique successfully gauged expert opinion on ASGM, and helped identify potential responses, policies and solutions for the sector. This is timely given that improvement to the ASGM sector is an important component within the UN Minamata Convention.

  13. DUPIC nuclear fuel manufacturing and process technology development

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Myung Seung; Park, J. J.; Lee, J. W. [and others

    2000-05-01

    In this study, DUPIC fuel fabrication technology and the active fuel laboratory were developed for the study of spent nuclear fuel. A new nuclear fuel using highly radioactive nuclear materials can be studied at the active fuel laboratory. Detailed DUPIC fuel fabrication process flow was developed considering the manufacturing flow, quality control process and material accountability. The equipment layout of about twenty DUPIC equipment at IMEF M6 hot cell was established for the minimization of the contamination during DUPIC processes. The characteristics of the SIMFUEL powder and pellets was studied in terms of milling conditions. The characteristics of DUPIC powder and pellet was studied by using 1 kg of spent PWR fuel at PIEF nr.9405 hot cell. The results were used as reference process conditions for following DUPIC fuel fabrication at IMEF M6. Based on the reference fabrication process conditions, the main DUPIC pellet fabrication campaign has been started at IMEF M6 using 2 kg of spent PWR fuel since 2000 January. As of March 2000, about thirty DUPIC pellets were successfully fabricated.

  14. DUPIC nuclear fuel manufacturing and process technology development

    International Nuclear Information System (INIS)

    Yang, Myung Seung; Park, J. J.; Lee, J. W.

    2000-05-01

    In this study, DUPIC fuel fabrication technology and the active fuel laboratory were developed for the study of spent nuclear fuel. A new nuclear fuel using highly radioactive nuclear materials can be studied at the active fuel laboratory. Detailed DUPIC fuel fabrication process flow was developed considering the manufacturing flow, quality control process and material accountability. The equipment layout of about twenty DUPIC equipment at IMEF M6 hot cell was established for the minimization of the contamination during DUPIC processes. The characteristics of the SIMFUEL powder and pellets was studied in terms of milling conditions. The characteristics of DUPIC powder and pellet was studied by using 1 kg of spent PWR fuel at PIEF nr.9405 hot cell. The results were used as reference process conditions for following DUPIC fuel fabrication at IMEF M6. Based on the reference fabrication process conditions, the main DUPIC pellet fabrication campaign has been started at IMEF M6 using 2 kg of spent PWR fuel since 2000 January. As of March 2000, about thirty DUPIC pellets were successfully fabricated

  15. Active Shop Scheduling Of Production Process Based On RFID Technology

    Directory of Open Access Journals (Sweden)

    Cuihua Chao

    2016-01-01

    Full Text Available In industry 4.0 environment, intelligent technology is almost applied to all parts of the manufacturing process, such as process design, job shop scheduling, etc.. This paper presents an efficient approach to job shop scheduling actively by using RFID to collect real-time manufacturing data. Identified the workpiece by RFID which needs to be machined, it can “ask for” the resource actively for the following process. With these active asking-for strategy, a double genetically encoded improved genetic algorithm is proposed for achieving active job shop scheduling solution during the actual manufacturing process. A case was used to evaluate its effectiveness. Meanwhile, , it can effectively and actively carry out job shop scheduling and has much better convergence effect comparing with basic genetic algorithm. And the job shop scheduler in management center can use the proposed algorithm to get the satisfied scheduling result timely by reducing waiting time and making begin time earlier during transmission between manufacturing process, which makes the scheduling result feasible and accurate.

  16. Research on application of computer technologies in jewelry process

    Directory of Open Access Journals (Sweden)

    Junbo Xia

    2017-06-01

    Full Text Available Jewelry production is a process of precious raw materials and low losses in processing. The traditional manual mode is unable to meet the needs of enterprises in reality, while the involvement of computer technology can just solve this practical problem. At present, the problem of restricting the application for computer in jewelry production is mainly a failure to find a production model that can serve the whole industry chain with the computer as the core of production. This paper designs a “synchronous and diversified” production model with “computer aided design technology” and “rapid prototyping technology” as the core, and tests with actual production cases, and achieves certain results, which are forward-looking and advanced.

  17. Centralisation of informatics (more effective processes via using new technologies)

    International Nuclear Information System (INIS)

    Cocher, L.

    2004-01-01

    In this paper author deals with next problems of Slovenske elektrarne, Plc (SE): - Centralisation and optimisation of informatics management; - New technologies within Integrated Informatics System IIS-SE: presentation of preliminary Project of 2 nd generation IIS-SE; - Centralisation of the selected data processing. At the present the intensive process of restructuring is taking place in SE, Plc, focused on increasing of the effectiveness of the pursued activities. In connection with this the Informatics section solves two projects: More effective self-management and human resources; Change of Informatics system architecture from decentralised to the centralised ones with an aim to consolidate all information and to make new conditions for higher mobility. (author)

  18. Environmental assessment for the Processing and Environmental Technology Laboratory (PETL)

    International Nuclear Information System (INIS)

    1995-09-01

    The U.S. Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Processing and Environmental Technology Laboratory (PETC) at Sandia National Laboratories/New Mexico (SNL/NM). This facility is needed to integrate, consolidate, and enhance the materials science and materials process research and development (R ampersand D) currently in progress at SNL/NM. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, an environmental impact statement is not required, and DOE is issuing this Finding of No Significant Impact (FONSI)

  19. Virtual Welded - Joint Design Integrating Advanced Materials and Processing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Zhishang; Ludewig, Howard W.; Babu, S. Suresh

    2005-06-30

    Virtual Welede-Joint Design, a systematic modeling approach, has been developed in this project to predict the relationship of welding process, microstructure, properties, residual stress, and the ultimate weld fatique strength. This systematic modeling approach was applied in the welding of high strength steel. A special welding wire was developed in this project to introduce compressive residual stress at weld toe. The results from both modeling and experiments demonstrated that more than 10x fatique life improvement can be acheived in high strength steel welds by the combination of compressive residual stress from the special welding wire and the desired weld bead shape from a unique welding process. The results indicate a technology breakthrough in the design of lightweight and high fatique performance welded structures using high strength steels.

  20. The evolution of waste management processes and technologies in BNFL

    International Nuclear Information System (INIS)

    Asquith, R. W.; Fairhall, G. A.

    1997-01-01

    The treatment of wastes arising from BNFL's nuclear fuel cycle operations can be traced through a number of phases. The first was the development of vitrification and cementation for fresh arising and plants are now in operation. To handle the mixed, heterogeneous intermediate level wastes, retrieval, segregation and robust treatment processes are at an advanced stage of development, with all plants to be operational from 2002. BNFL is focusing attention on reducing waste management lifetime costs including reducing waste volumes of source. Technologies aimed at significant reductions are now being developed. The final phase, now in progress, recognizes the need for an integrated approach to advanced fuel cycle processes which incorporates BNFL holistic concept. (author) 6 refs., 1 fig

  1. Environmental assessment for the Processing and Environmental Technology Laboratory (PETL)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The U.S. Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Processing and Environmental Technology Laboratory (PETC) at Sandia National Laboratories/New Mexico (SNL/NM). This facility is needed to integrate, consolidate, and enhance the materials science and materials process research and development (R&D) currently in progress at SNL/NM. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, an environmental impact statement is not required, and DOE is issuing this Finding of No Significant Impact (FONSI).

  2. Minimally Processed Functional Foods: Technological and Operational Pathways.

    Science.gov (United States)

    Rodgers, Svetlana

    2016-10-01

    This paper offers a concise review of technical and operational concepts underpinning commercialization of minimally processed functional foods (FFs), foods with fresh-like qualities commanding premium prices. The growing number of permitted nutritional content/health claims, many of which relate to well-being, coupled with emerging extraction and food processing technologies offers new exciting opportunities for small and medium size enterprises (SMEs) specializing in fresh produce to play an active role in the health market. Supporting SMEs, governments could benefit from savings in healthcare costs and value creation in the economy. Consumers could benefit from novel FF formats such as refrigerated RTE (ready-to-eat) meals, a variety of fresh-like meat-, fish-, and egg-based products, fresh-cut fruits and vegetables, cereal-based fermented foods and beverages. To preserve these valuable commodities, mild biological (enzymatic treatment, fermentation and, bio-preservation) and engineering solutions are needed. The latter include nonthermal techniques such as high-pressure treatment, cook-chill, sous-vide, mirco-encapsulation, vacuum impregnation and others. "De-constructive" culinary techniques such as 3D food printing and molecular gastronomy as well as developments in nutrigenomics and digital technologies facilitate novel product formats, personalization and access to niche markets. In the operational sense, moving from nourishment to health improvement demands a shift from defensive market-oriented to offensive market-developing strategies including collaborative networks with research organizations. © 2016 Institute of Food Technologists®.

  3. Efficient Separations and Processing Crosscutting Program. Technology summary

    International Nuclear Information System (INIS)

    1995-06-01

    The Efficient Separations and Processing (ESP) Crosscutting Program was created in 1991 to identify, develop, and perfect separations technologies and processes to treat wastes and address environmental problems throughout the DOE Complex. The ESP funds several multi-year tasks that address high-priority waste remediation problems involving high-level, low-level, transuranic, hazardous, and mixed (radioactive and hazardous) wastes. The ESP supports applied research and development (R and D) leading to demonstration or use of these separations technologies by other organizations within DOE-EM. Treating essentially all DOE defense wastes requires separation methods that concentrate the contaminants and/or purify waste streams for release to the environment or for downgrading to a waste form less difficult and expensive to dispose of. Initially, ESP R and D efforts focused on treatment of high-level waste (HLW) from underground storage tanks (USTs) because of the potential for large reductions in disposal costs and hazards. As further separations needs emerge and as waste management and environmental restoration priorities change, the program has evolved to encompass the breadth of waste management and environmental remediation problems

  4. Using information technology to support knowledge conversion processes

    Directory of Open Access Journals (Sweden)

    2001-01-01

    Full Text Available One of the main roles of Information Technology in Knowledge Management programs is to accelerate the speed of knowledge transfer and creation. The Knowledge Management tools intend to help the processes of collecting and organizing the knowledge of groups of individuals in order to make this knowledge available in a shared base. Due to the largeness of the concept of knowledge, the software market for Knowledge Management seems to be quite confusing. Technology vendors are developing different implementations of the Knowledge Management concepts in their software products. Because of the variety and quantity of Knowledge Management tools available on the market, a typology may be a valuable aid to organizations that are looking for answers to specific needs. The objective of this article is to present guidelines that help to design such a typology. Knowledge Management solutions such as intranet systems, Electronic Document Management (EDM, groupware, workflow, artificial intelligence-based systems, Business Intelligence (BI, knowledge map systems, innovation support, competitive intelligence tools and knowledge portals are discussed in terms of their potential contributions to the processes of creating, registering and sharing knowledge. A number of Knowledge Management tools (Lotus Notes, Microsoft Exchange, Business Objects, Aris Toolset, File Net, Gingo, Vigipro, Sopheon have been checked. The potential of each category of solutions to support the transfer of tacit and/or explicit knowledge and to facilitate the knowledge conversion spiral in the sense of Nonaka and Takeuchi (1995 is discussed.

  5. Use of radiation processing technology gradually expands in industry

    International Nuclear Information System (INIS)

    Anon.

    1989-01-01

    The use of radioisotopes and radiation is expanding in the fields of industries and medicine with a high potentiality of the application to environmental protection. The technology transfer on the use of isotopes and radiation is progressing in the framework of international cooperation. But the industry has maintained wait and see attitude on the commercialization of food irradiation. Such present features were the highlight in the 19th Japan Conference on Radiation and Radioisotopes held on November 14-16. 72 papers from 19 countries were presented and discussed in 13 sessions. The progress of accelerator technology has contributed to the expansion of radiation processing market. The importance of the application of isotopes and radiation to environmental protection has been gradually acknowledged, and the electron beam treatment of flue gas for acid rain abatement and the elimination of chlorinated ethylene from drinking water were discussed. Drastic change has not been seen in the climate of food irradiation, however there are several positive indicators which support the prediction of slow but steady progress in the commercialization of the process and the trade of irradiated foods. (K.I.)

  6. FOOD PROCESSING TECHNOLOGY AS A MEDIATOR OF FUNCTIONALITY. STRUCTURE-PROPERTY-PROCESS RELATIONSHIPS

    Directory of Open Access Journals (Sweden)

    Ester Betoret

    2015-02-01

    Full Text Available During the last years, the food industry has been facing technical and economic changes both in society and in the food processing practices, paying high attention to food products that meet the consumers´ demands. In this direction, the study areas in food process and products have evolved mainly from safety to other topics such as quality, environment or health. The improvement of the food products is now directed towards ensuring nutritional and specific functional benefits. Regarding the processes evolution, they are directed to ensure the quality and safety of environmentally friendly food products produced optimizing the use of resources, minimally affecting or even enhancing their nutritional and beneficial characteristics. The product structure both in its raw form and after processing plays an important role maintaining, enhancing and delivering the bioactive compounds in the appropriate target within the organism. The aim of this review is to make an overview on some synergistic technologies that can constitute a technological process to develop functional foods, enhancing the technological and/or nutritional functionality of the food products in which they are applied. More concretely, the effect of homogenization, vacuum impregnation and drying operations on bioactive compounds have been reviewed, focusing on the structure changes produced and its relationship on the product functionality, as well as on the parameters and the strategies used to quantify and increase the achieved functionality.

  7. Developing a model for assessing biomass processing technologies within a local biomass processing depot.

    Science.gov (United States)

    Bals, Bryan D; Dale, Bruce E

    2012-02-01

    One solution to the supply chain challenges of cellulosic biofuels is a network of local biomass processing depots (LBPDs) that can produce stable, dense, intermediate commodities and valuable co-products prior to shipping to a refinery. A techno-economic model of an LBPD facility that could incorporate multiple technologies and products was developed in Microsoft Excel to be used to economically and environmentally evaluate potential LBPD systems. In this study, three technologies (ammonia fiber expansion or AFEX™ pretreatment, fast pyrolysis, and leaf protein processing) were assessed for profitability. Pyrolysis was slightly profitable under the base conditions, leaf protein processing was highly unprofitable, and AFEX was profitable if biomass drying was not required. This model can be adapted to multiple feedstocks and end uses, including both economic and environmental modeling. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. Technical Reviews on Pattern Recognition in Process Analytical Technology

    International Nuclear Information System (INIS)

    Kim, Jong Yun; Choi, Yong Suk; Ji, Sun Kyung; Park, Yong Joon; Song, Kyu Seok; Jung, Sung Hee

    2008-12-01

    Pattern recognition is one of the first and the most widely adopted chemometric tools among many active research area in chemometrics such as design of experiment(DoE), pattern recognition, multivariate calibration, signal processing. Pattern recognition has been used to identify the origin of a wine and the time of year that the vine was grown by using chromatography, cause of fire by using GC/MS chromatography, detection of explosives and land mines, cargo and luggage inspection in seaports and airports by using a prompt gamma-ray activation analysis, and source apportionment of environmental pollutant by using a stable isotope ratio mass spectrometry. Recently, pattern recognition has been taken into account as a major chemometric tool in the so-called 'process analytical technology (PAT)', which is a newly-developed concept in the area of process analytics proposed by US Food and Drug Administration (US FDA). For instance, identification of raw material by using a pattern recognition analysis plays an important role for the effective quality control of the production process. Recently, pattern recognition technique has been used to identify the spatial distribution and uniformity of the active ingredients present in the product such as tablet by transforming the chemical data into the visual information

  9. Cogeneration Technology Alternatives Study (CTAS). Volume 3: Industrial processes

    Science.gov (United States)

    Palmer, W. B.; Gerlaugh, H. E.; Priestley, R. R.

    1980-01-01

    Cogenerating electric power and process heat in single energy conversion systems rather than separately in utility plants and in process boilers is examined in terms of cost savings. The use of various advanced energy conversion systems are examined and compared with each other and with current technology systems for their savings in fuel energy, costs, and emissions in individual plants and on a national level. About fifty industrial processes from the target energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidate which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on site gasification of coal. An attempt was made to use consistent assumptions and a consistent set of ground rules specified by NASA for determining performance and cost. Data and narrative descriptions of the industrial processes are given.

  10. Microbial ecology and starter culture technology in coffee processing.

    Science.gov (United States)

    Vinícius de Melo Pereira, Gilberto; Soccol, Vanete Thomaz; Brar, Satinder Kaur; Neto, Ensei; Soccol, Carlos Ricardo

    2017-09-02

    Coffee has been for decades the most commercialized food product and most widely consumed beverage in the world, with over 600 billion cups served per year. Before coffee cherries can be traded and processed into a final industrial product, they have to undergo postharvest processing on farms, which have a direct impact on the cost and quality of a coffee. Three different methods can be used for transforming the coffee cherries into beans, known as wet, dry, and semi-dry methods. In all these processing methods, a spontaneous fermentation is carried out in order to eliminate any mucilage still stuck to the beans and helps improve beverage flavor by microbial metabolites. The microorganisms responsible for the fermentation (e.g., yeasts and lactic acid bacteria) can play a number of roles, such as degradation of mucilage (pectinolytic activity), inhibition of mycotoxin-producing fungi growth, and production of flavor-active components. The use of starter cultures (mainly yeast strains) has emerged in recent years as a promising alternative to control the fermentation process and to promote quality development of coffee product. However, scarce information is still available about the effects of controlled starter cultures in coffee fermentation performance and bean quality, making it impossible to use this technology in actual field conditions. A broader knowledge about the ecology, biochemistry, and molecular biology could facilitate the understanding and application of starter cultures for coffee fermentation process. This review provides a comprehensive coverage of these issues, while pointing out new directions for exploiting starter cultures in coffee processing.

  11. A study of the ion-beam process technology

    International Nuclear Information System (INIS)

    Kanayama, Toshihiko

    1990-01-01

    This paper concerns the ion-beam technology for fabrication of semiconductor devices. The purpose of the present work is to find out useful irradiation effects of ion beams and to develop them into fabrication-process technologies. In particular, the advantage of the focused ion beam (FIB) is pursued to be utilized in fabrication of fine structures; the mask for the x-ray lithography is selected as a test target for this purpose. The mechanism of each irradiation effect is also investigated in detail to give the basis of the process developed. This paper consists of seven chapters. The first one gives an overview of the present work. Chapter 2 deals with ion-bombardment effect on the internal stress of deposited metals. The subject of Chapter 3 is the enhancement effect of chemical etching rate by ion bombardment. This chapter also discusses pattern replicability of the synchrotron-radiation x-ray lithography using the exposure results of the x-ray masks fabricated with the Al 2 O 3 resist and the stress compensation technique discussed in Chapter 2. Chapter 4 is devoted to the atomic intermixing effect caused by ion bombardment. The purpose of the latter half of this chapter is to demonstrate that this mixing effect has a high spatial resolution and deserves to be used as a definition process of fine structures by the FIB. Chapter 5 describes a unique effect of the ion beam: solid phase epitaxy of amorphous Si induced by bombardment at elevated temperatures. Chapter 6 demonstrates that maskless ion implantation using the FIB is a very efficient and productive technique for fabrication of small Hall sensors with sub-micron feature sizes. Finally, Chapter 7 summarizes the conclusions obtained in this work. (J.P.N.) 270 refs

  12. LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

    Energy Technology Data Exchange (ETDEWEB)

    King, W

    2007-11-30

    loading, and handling of liquid wash and conditioning solutions. RF processing requires handling and evaporation of cesium eluates, disposal of spent organic resin, and handling of the various liquid wash and regenerate solutions used. In both cases, the DSS will be immobilized in a low activity waste form. It appears that both technologies are mature, well studied, and generally suitable for this application. Technology selection will likely be based on downstream impacts or preferences between the various processing options for the two materials rather than on some unacceptable performance property identified for one material. As a result, the following detailed technical review and summary of the two technologies should be useful to assist in technology selection for SCIX.

  13. LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

    International Nuclear Information System (INIS)

    King, W.

    2007-01-01

    loading, and handling of liquid wash and conditioning solutions. RF processing requires handling and evaporation of cesium eluates, disposal of spent organic resin, and handling of the various liquid wash and regenerate solutions used. In both cases, the DSS will be immobilized in a low activity waste form. It appears that both technologies are mature, well studied, and generally suitable for this application. Technology selection will likely be based on downstream impacts or preferences between the various processing options for the two materials rather than on some unacceptable performance property identified for one material. As a result, the following detailed technical review and summary of the two technologies should be useful to assist in technology selection for SCIX

  14. Process Analytical Technology (PAT): batch-to-batch reproducibility of fermentation processes by robust process operational design and control.

    Science.gov (United States)

    Gnoth, S; Jenzsch, M; Simutis, R; Lübbert, A

    2007-10-31

    The Process Analytical Technology (PAT) initiative of the FDA is a reaction on the increasing discrepancy between current possibilities in process supervision and control of pharmaceutical production processes and its current application in industrial manufacturing processes. With rigid approval practices based on standard operational procedures, adaptations of production reactors towards the state of the art were more or less inhibited for long years. Now PAT paves the way for continuous process and product improvements through improved process supervision based on knowledge-based data analysis, "Quality-by-Design"-concepts, and, finally, through feedback control. Examples of up-to-date implementations of this concept are presented. They are taken from one key group of processes in recombinant pharmaceutical protein manufacturing, the cultivations of genetically modified Escherichia coli bacteria.

  15. Investigation of process equipment in petrochemical industry using radioisotope technology

    International Nuclear Information System (INIS)

    Mohammed, M. S.

    2007-04-01

    Applications of radioisotope technology have proved it self to be an effective techniques for troubleshooting and optimizing industrial process in petrochemical industry. In this study, Khartoum refinery was investigated by gamma scanning technique for better understanding of malfunctions, the scanning were carried out using 60 C gamma radiation source with activity of 50 mCi on fractionator and stripper columns, obtained results showed that all trays of the fractionator column were in place but weeping was evident due to fouling or partial tray damage. For the stripper column, results obtained showed that all trays were on their positions and no process anomalies taking place. Heat exchanger was also examined using radiotracer technique with respect to leak detection and residence time distribution. The investigations were carried out using 82 Br in the form of di-bromo-para-bensene (C 6 H 4 Br 2 ) as a radiotracer. No leak was recorded and the residence time distribution results showed that the process functions were quite normal. Leak was examined using 99m Tc as a radiotracer detection to demonstrate the potentials of the technique. The testing was conducted using reflux condenser. Obtained results proved that the technique is sensitive, reliable and can be adopted to investigate heat exchangers in industrial systems.(Author)

  16. Process technology of luwak coffee through bioreactor utilization

    Science.gov (United States)

    Hadipernata, M.; Nugraha, S.

    2018-01-01

    Indonesia has an advantage in producing exotic coffee that is Luwak coffee. Luwak coffee is produced from the fermentation process in digestion of civet. Luwak coffee production is still limited due to the difficulty level in the use of civet animals as the only medium of Luwak coffee making. The research was conducted by developing technology of luwak coffee production through bioreactor utilization and addition the bacteria isolate from gastric of civet. The process conditions in the bioreactor which include temperature, pH, and bacteria isolate of civet are adjusted to the process that occurs in civet digestion, including peristaltic movement on the stomach and small intestine of the civet will be replaced by the use of propellers that rotate on the bioreactor. The result of research showed that proximat analysis data of artificial/bioreactor luwak coffee did not significant different with original luwak coffee. However, the original luwak coffee has higher content of caffeine compared to bioreactor luwak coffee. Based on the cuping test the bioreactor luwak coffee has a value of 84.375, while the original luwak coffee is 84.875. As the result, bioreactor luwak coffee has excellent taste that similiar with original luwak coffee taste.

  17. Budget Options

    National Research Council Canada - National Science Library

    2000-01-01

    This volume-part of the Congressional Budget Office's (CBO's) annual report to the House and Senate Committees on the Budget-is intended to help inform policymakers about options for the federal budget...

  18. THz spectroscopy: An emerging technology for pharmaceutical development and pharmaceutical Process Analytical Technology (PAT) applications

    Science.gov (United States)

    Wu, Huiquan; Khan, Mansoor

    2012-08-01

    As an emerging technology, THz spectroscopy has gained increasing attention in the pharmaceutical area during the last decade. This attention is due to the fact that (1) it provides a promising alternative approach for in-depth understanding of both intermolecular interaction among pharmaceutical molecules and pharmaceutical product quality attributes; (2) it provides a promising alternative approach for enhanced process understanding of certain pharmaceutical manufacturing processes; and (3) the FDA pharmaceutical quality initiatives, most noticeably, the Process Analytical Technology (PAT) initiative. In this work, the current status and progress made so far on using THz spectroscopy for pharmaceutical development and pharmaceutical PAT applications are reviewed. In the spirit of demonstrating the utility of first principles modeling approach for addressing model validation challenge and reducing unnecessary model validation "burden" for facilitating THz pharmaceutical PAT applications, two scientific case studies based on published THz spectroscopy measurement results are created and discussed. Furthermore, other technical challenges and opportunities associated with adapting THz spectroscopy as a pharmaceutical PAT tool are highlighted.

  19. Information service on new and emerging health technologies: identification and prioritization processes for a European union-wide newsletter.

    Science.gov (United States)

    Wild, Claudia; Simpson, Sue; Douw, Karla; Geiger-Gritsch, Sabine; Mathis, Stefan; Langer, Thomas

    2009-12-01

    EUnetHTA WP 7 (Strand B) aimed to promote sharing information on new and emerging technologies. The task was to develop a prototype of a newsletter and pilot the processes of production. The EuroScan database served as information source on pertinent technologies. To prioritize, a set of criteria for scoring the potential impact and for selecting the technologies for articles was applied and a pilot newsletter was produced. Being objective and transparent about the content of a newsletter required a method for prioritizing health technologies. Using significance criteria, members of the prioritization panel selected twelve technologies for articles of different length and depth. Potential recipients, surveyed on relevance, content, timeliness, and readability responded mostly positive, but requested more information on cost effectiveness and criticized timeliness. Dissemination of an EU-wide newsletter would be feasible, but time-consuming. Although a newsletter appears to fulfill a need for information on emerging and new health technologies, it is not considered the right tool to avoid duplication of effort in the present international constellation of horizon scanning for new health technologies. Other options will be pursued as part of future collaborative actions, for example, a core set of early awareness information, or an on-demand electronic information system.

  20. Intelligent technologies in process of highly-precise products manufacturing

    Science.gov (United States)

    Vakhidova, K. L.; Khakimov, Z. L.; Isaeva, M. R.; Shukhin, V. V.; Labazanov, M. A.; Ignatiev, S. A.

    2017-10-01

    One of the main control methods of the surface layer of bearing parts is the eddy current testing method. Surface layer defects of bearing parts, like burns, cracks and some others, are reflected in the results of the rolling surfaces scan. The previously developed method for detecting defects from the image of the raceway was quite effective, but the processing algorithm is complicated and lasts for about 12 ... 16 s. The real non-stationary signals from an eddy current transducer (ECT) consist of short-time high-frequency and long-time low-frequency components, therefore a transformation is used for their analysis, which provides different windows for different frequencies. The wavelet transform meets these conditions. Based on aforesaid, a methodology for automatically detecting and recognizing local defects in bearing parts surface layer has been developed on the basis of wavelet analysis using integral estimates. Some of the defects are recognized by the amplitude component, otherwise an automatic transition to recognition by the phase component of information signals (IS) is carried out. The use of intelligent technologies in the manufacture of bearing parts will, firstly, significantly improve the quality of bearings, and secondly, significantly improve production efficiency by reducing (eliminating) rejections in the manufacture of products, increasing the period of normal operation of the technological equipment (inter-adjustment period), the implementation of the system of Flexible facilities maintenance, as well as reducing production costs.

  1. Radiation processing technology for industrial waste water treatment

    International Nuclear Information System (INIS)

    2011-01-01

    Radiation sterilization technology, cross-linked polymers and curing, food and environmental applications of the radiation is widely used for many years. At the same time, drinking water and wastewater treatment are the part of the radiation technology applications. For this purpose, drinking water and wastewater treatment plants in various countries has been established. In this project, gamma / electron beam radiation treatment is intended to be used for the treatment of alkaloid, textiles and polychlorinated biphenyls (PCBs) wastewater. In this regard, the chemical characterization of wastewater, the interaction with radiation, biological treatment and determination of toxicological properties are the laboratory studies milestones. After laboratory studies, the establishment of a pilot scale treatment plant has been planned. Within the framework of the project a series of dye used in textile industry were examined. Besides the irradiation, the changes in treatment efficiency were investigated by using of oxygen and hydrogen peroxide in conjunction with the irradiation. Same working methods were implemented in the wastewater treatment of Bolvadin Opium Alkaloid Factory as well. In addition to chemical analysis in this study, aerobic and anaerobic biological treatment process also have been applied. Standard reference materials has been used for the marine sediment study contaminated with polychlorinated biphenyls.

  2. Small Scale Turbopump Manufacturing Technology and Material Processes

    Science.gov (United States)

    Alvarez, Erika; Morgan, Kristin; Wells, Doug; Zimmerman, Frank

    2011-01-01

    As part of an internal research and development project, NASA Marshall Space Flight Center (MSFC) has been developing a high specific impulse 9,000-lbf LOX/LH2 pump-fed engine testbed with the capability to throttle 10:1. A Fuel Turbopump (FTP) with the ability to operate across a speed range of 30,000-rpm to 100,000-rpm was developed and analyzed. This small size and flight-like Fuel Turbopump has completed the design and analysis phase and is currently in the manufacturing phase. This paper highlights the manufacturing and processes efforts to fabricate an approximately 20-lb turbopump with small flow passages, intricately bladed components and approximately 3-in diameter impellers. As a result of the small scale and tight tolerances of the hardware on this turbopump, several unique manufacturing and material challenges were encountered. Some of the technologies highlighted in this paper include the use of powder metallurgy technology to manufacture small impellers, electron beam welding of a turbine blisk shroud, and casting challenges. The use of risk reduction efforts such as non-destructive testing (NDT) and evaluation (NDE), fractography, material testing, and component spin testing are also discussed in this paper.

  3. Synthesis and post-processing of nanomaterials using microreaction technology

    International Nuclear Information System (INIS)

    Chang, Chih-Hung; Paul, Brian K.; Remcho, Vincent T.; Atre, Sundar; Hutchison, James E.

    2008-01-01

    A critical barrier to the routine use of nanomaterials is the tedious, expensive means of their synthesis. Microreaction technology takes advantage of the large surface area-to-volume ratios within microchannel structures to accelerate heat and mass transport. This accelerated transport allows for rapid changes in reaction temperatures and concentrations leading to more uniform heating and mixing which can have dramatic impacts on macromolecular yields and nanoparticle size distributions. Benefits of microreaction technology include higher yield and reactant conversion, better energy efficiency and less by-product generation. Microreactors can help minimize the environmental impact of nanoproduction by enabling solvent free mixing, integrated separation techniques and reagent recycling. The possibility of synthesizing nanomaterials in the required volumes at the point-of-use eliminates the need to store and transport potentially hazardous materials and provides the flexibility for tailoring complex functional nanomaterials. Recognizing these benefits for nanosynthesis, continuous flow microreactors have been used by several research groups to synthesize and characterize nanomaterials. An overview of these efforts and issues related to scale up and other post synthesis processes such as separation and deposition are presented in this paper.

  4. Technology of irradiation processing for checking garlic sprouting

    International Nuclear Information System (INIS)

    Chen Yuntang

    1999-01-01

    Study on technology of irradiation processing for checking garlic sprouting was carried out. The results are as follows. 1. the suitable irradiation time of garlic could be prolonged when the garlic was preserved at low temperature (-2 +- 1 degree C). When the garlic was stored till the end of the year and then irradiated, the sprouting could be checked effectively. When the garlic was stored till the next March, the effect of sprouting inhibition decreased; 2. When garlic was irradiated at suitable time and then subsequently stored at low temperature, the effect of sprouting inhibition was the same as that with cold storage before irradiation. However, if the cold storage period was rather long, the effect was not as good as that with cold storage after irradiation; 3. Browning of irradiated garlic did not occur when the garlic was preserved at low temperature (-2 +- 1 degree C), indicating that the browning of sprout and bud was caused by higher storage temperature

  5. Carotenoids Functionality, Sources, and Processing by Supercritical Technology: A Review

    Directory of Open Access Journals (Sweden)

    Natália Mezzomo

    2016-01-01

    Full Text Available Carotenoid is a group of pigments naturally present in vegetal raw materials that have biological properties. These pigments have been used mainly in food, pharmaceutical, and cosmetic industries. Currently, the industrial production is executed through chemical synthesis, but natural alternatives of carotenoid production/attainment are in development. The carotenoid extraction occurs generally with vegetal oil and organic solvents, but supercritical technology is an alternative technique to the recovery of these compounds, presenting many advantages when compared to conventional process. Brazil has an ample diversity of vegetal sources inadequately investigated and, then, a major development of optimization and validation of carotenoid production/attainment methods is necessary, so that the benefits of these pigments can be delivered to the consumer.

  6. Technological processes - environment - ecological problems. Tehnoloski procesi - okruzenje - ekoloski problemi

    Energy Technology Data Exchange (ETDEWEB)

    Hovanec, G.; Knezevic, D.; Bicanski, J.; Monevski, B.; Milovic, M. (Rudarski Institut, Zemun (Yugoslavia))

    1990-01-01

    Deals with environmental pollution caused by coal fired power plants and by ore mining and ore processing plants in Yugoslavia. Air, land and water pollution by Serbian zinc and copper flotation plants is described. Various technological features of zinc flotation plants and their waste disposal methods as well as copper mines are provided. Measures aimed at reducing land and water pollution recommended by the Mining Institute in Zemun are highlighted. Air, land and water pollution by major Yugoslav power plants is further reviewed. These plants, fired by low grade lignite and brown coal, produce 11 Mt/a of slag and fly ash. Chemical ash properties, features of ash disposal sites and measures for recultivating devastated land in the vicinity of power plants are pointed out. 2 tabs.

  7. 49 CFR 232.503 - Process to introduce new brake system technology.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Process to introduce new brake system technology... Technology § 232.503 Process to introduce new brake system technology. (a) Pursuant to the procedures... brake system technology, prior to implementing the plan. (b) Each railroad shall complete a pre-revenue...

  8. Role of radiation processing in technological development of the world

    International Nuclear Information System (INIS)

    Chmielewski, G. Andrzej.; Berejka, J. Anthony.

    2012-01-01

    Full text: Radiation processing is based on application of gamma industrial sources and electron accelerators. Recently development of high power accelerators made a operation mode of e/X as a viable tool for these applications as well. Included in this are service type facilities operated in Research and Development centers. When other uses are taken into account, there are in total over 300 gamma irradiators being operated for a variety of purposes in 55 different countries. 100-120 gamma irradiators are located in Europe and in the United States. Recent developments in very high current accelerators show considerable promise for the industrial use of X rays as a future technology of choice. X ray comparable in penetration to gamma rays. The use of high energy X rays for sterilizing medical devices was proposed during the 1960th, but not implemented until the late 1990th. X-rays are comparable in penetration to gamma emissions from radioactive isotopes, but being electrically sourced can be turned on or off not posing the storage, supply and transport issues associated with the use of isotopes. The development of nana-composites, which is only a few years old, is very promising. This includes the development of nano-gels. This nano-gels can be used for drug or vaccine delivery and are especially suited for the delivery of anti-cancer agents into tumor tissues. The use of natural polymers and fibers is another growing area in the use of radiation processing. Radiation processing is also being used to enhance befoul manufacture. Food the hygenization is other important application of radiation processing and finally environmental applications are still challenging field or radiation use.

  9. Traditional fish processing: technology, quality development and evaluation

    International Nuclear Information System (INIS)

    Nketsia-Tabiri, J.

    1994-01-01

    Traditional fish processing technologies are important in the preservation and utilization of fish in many developing countries. These technologies as well as the quality of the products arc poorly defined and understood. This study therefore investigated the production, quality characteristics and utilization of traditional cured fish products using field surveys and laboratory techniques. It was found that simple traditional technologies for smoking, salting and drying are used to process fish in Ghana; infrastructural requirements for traditional fish processing have high local material input. The cured fish products have distinct sensory, physico-chemical properties and variable storage characteristics. Processors' perceptions of important quality attributes of cured fish products were linked to storage, marketing and other product delivery characteristics. Consumers' perceptions and expectations of desirable quality attributes however were found to he dependent upon the type of cured fish product and the food in which it is used. Cost was found to be the most important factor influencing the utilization of animal protein foods; other factors were nutritional quality, beliefs and food habits. Animal protein consumers showed a high preference for fish in general and cured fish products in particular. U sing central composite rotatable design for k = 3, representing salting time (0 - 24), drying temperature (40°C - 60°C) and drying time (6 - 20 hours), equations for predicting objective and subjective quality indices were developed. The critical salting time for attaining minimum moisture content were 20.5, 12 and 8.5 hours respectively for products dried at 40°C, 50°C and 60°C. At each salting time, the mean hardness score was dependent on the drying temperature and drying time whilst the mean colour and overall acceptability scores were influenced by drying temperature. It was found that the long salting time (24-72 hours) and drying time (5

  10. Feasibility study on co-processing technology; Co-processing gijutsu no kigyoka kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Co-processing is a technology producing light oil by hydrocracking of mixtures of coal and heavy oils (tar sand bitumen, heavy oil) as rich resources. The feasibility study on co-processing technology was carried out to improve its profitability and promote its practical use. The United States DOE is promoting the co-processing program to enhance reaction rates through utilization of modified catalysts and optimization of the first and second stage temperatures, and to perform catalyst activity screening including new high- activity ebullated-bed catalysts, dispersed catalysts, extrusion molded catalysts, and combinations of them. DOE is also promoting the study on the reactant/product of coal- derived liquid and/or petroleum derived residues, improvement of a liquid yield and product quality in a two-stage reactor, and optimization of the co-processing system by interstage hydrotreating. Two test results showed higher effectiveness than previous ones. In addition, the possibility of the co-processing system was studied by autoclave test of coal/oil sand bitumen. Its feasibility in China was also studied. 44 figs., 31 tabs.

  11. Global Assessment of Hydrogen Technologies – Tasks 3 & 4 Report Economic, Energy, and Environmental Analysis of Hydrogen Production and Delivery Options in Select Alabama Markets: Preliminary Case Studies

    Energy Technology Data Exchange (ETDEWEB)

    Fouad, Fouad H.; Peters, Robert W.; Sisiopiku, Virginia P.; Sullivan Andrew J.; Gillette, Jerry; Elgowainy, Amgad; Mintz, Marianne

    2007-12-01

    This report documents a set of case studies developed to estimate the cost of producing, storing, delivering, and dispensing hydrogen for light-duty vehicles for several scenarios involving metropolitan areas in Alabama. While the majority of the scenarios focused on centralized hydrogen production and pipeline delivery, alternative delivery modes were also examined. Although Alabama was used as the case study for this analysis, the results provide insights into the unique requirements for deploying hydrogen infrastructure in smaller urban and rural environments that lie outside the DOE’s high priority hydrogen deployment regions. Hydrogen production costs were estimated for three technologies – steam-methane reforming (SMR), coal gasification, and thermochemical water-splitting using advanced nuclear reactors. In all cases examined, SMR has the lowest production cost for the demands associated with metropolitan areas in Alabama. Although other production options may be less costly for larger hydrogen markets, these were not examined within the context of the case studies.

  12. Defense Waste Processing Facility: Report of task force on options to mitigate the effect of nitrite on DWPF operations. Savannah River Site 200-S Area

    Energy Technology Data Exchange (ETDEWEB)

    Randall, D. [ed.; Marek, J.C.

    1992-03-01

    The possibility of accumulating ammonium nitrate (an explosive) as well as organic compounds in the DWPF Chemical Processing Cell Vent System was recently discovered. A task force was therefore organized to examine ways to avoid this potential hazard. Of thirty-two processing/engineering options screened, the task force recommended five options, deemed to have the highest technical certainty, for detailed development and evaluation: Radiolysis of nitrite in the tetraphenylborate precipitate slurry feed in a new corrosion-resistant facility. Construction of a Late Washing Facility for precipitate washing before transfer to the DWPF; ``Just-in-Time`` precipitation; Startup Workaround by radiolysis of nitrite in the existing corrosion-resistant Pump Pit tanks; Ammonia venting and organics separation in the DWPF; and, Estimated costs and schedules are included in this report.

  13. Designing a climate change policy for the international maritime transport sector: Market-based measures and technological options for global and regional policy actions

    International Nuclear Information System (INIS)

    Miola, A.; Marra, M.; Ciuffo, B.

    2011-01-01

    The international maritime transport sector has a significant abatement potential and some technical improvements that reduce GHG emissions would already be profitable without any policy in place. This paper analyses in-depth the limits and opportunities of policy options currently under consideration at the international level to stimulate the sector to reduce its GHG emissions. In particular, in order for the maritime transport sector to become more environmentally friendly, the flexible nature of international market-based measures and the European Union Emission Trading Scheme provide a definite window of opportunity without placing unnecessary high burden on the sector. However, the development of a regional policy, such as at European level, for the international maritime transport sector faces several obstacles: allocation of emissions, carbon leakage, permit allocation, treatment of the great variety in ship type, size and usage, and transaction cost. Global market-based policies could overcome most of these challenges. This paper provides an in-depth analysis of the policy instruments currently under discussion to reduce the sector's burden on the environment, and focuses on economic theory, legal principles, technological options, and the political framework that together make up the basis of decision-making regarding the international maritime transport sector's climate change policies. - Highlights: → Technologies for a more environmental friendly maritime transport sector and their cost-effectiveness. → How to combine ambitious CO 2 reduction goals with a sector-wide market-based policy. → Permits should be auctioned frequently and small emitters have to be excluded. → Inclusion of shipping in the EU ETS causes carbon leakage, so the policy should aim at expansion.

  14. 3. Research Coordination Meeting (RCM) of the Coordinated Research Project (CRP) on 'Studies of advanced reactor technology options for effective incineration of radioactive waste'. Working material

    International Nuclear Information System (INIS)

    2007-01-01

    To meet expressed Member States' needs, the IAEA has initiated a Coordinated Research Project (CRP) on 'Studies of Advanced Reactor Technology Options for Effective Incineration of Radioactive Waste'. The final goal of the CRP is to deepen the understanding of the dynamics of transmutation systems, e.g. the accelerator driven system, especially systems with deteriorated safety parameters, qualify the available methods, specify the range of validity of methods, and formulate requirements for future theoretical developments. Should transient experiments be available, the CRP will pursue experimental benchmarking work. In any case, based on the results, the CRP will conclude on the potential need of transient experiments and make appropriate proposals for experimental programs. The Technical Meeting in Chennai was the 3rd Research Coordination Meeting (RCM) of the CRP The man objectives of the RCM were to: - Discuss and perform inter-comparisons of the various benchmark results; - Prepare the first draft of the final CRP Report Status of the analyses and inter-comparisons of the results. The main objective of the CRP was to study innovative technology options for incinerating/utilizing radioactive wastes. The CRP's benchmarking exercises focused on eight innovative transmutation 'Domains', which correspond to different critical and sub-critical concepts or groups of concepts: I. Critical fast reactor, solid fuel, with fertile; II. Critical fast reactor, solid fuel, fertile-free; III. ADS, solid fuel, with fertile; IV. ADS, solid fuel, fertile-free; V. Critical reactor and ADS, molten salt fuel, with fertile; VI. Critical reactor and ADS, molten salt fuel, fertile-free; VII. Critical fast reactor and ADS, gas cooled; VIII. Fusion/fission hybrid system. For each of these Domains, the discussions and inter-comparisons considered the following issues: - Reactor-models; - Scenarios/phenomena; - Static analyses; - Dynamic analyses; - Methods; - Codes; - Neutronic data base

  15. Forensic print extraction using 3D technology and its processing

    Science.gov (United States)

    Rajeev, Srijith; Shreyas, Kamath K. M.; Panetta, Karen; Agaian, Sos S.

    2017-05-01

    Biometric evidence plays a crucial role in criminal scene analysis. Forensic prints can be extracted from any solid surface such as firearms, doorknobs, carpets and mugs. Prints such as fingerprints, palm prints, footprints and lip-prints can be classified into patent, latent, and three-dimensional plastic prints. Traditionally, law enforcement officers capture these forensic traits using an electronic device or extract them manually, and save the data electronically using special scanners. The reliability and accuracy of the method depends on the ability of the officer or the electronic device to extract and analyze the data. Furthermore, the 2-D acquisition and processing system is laborious and cumbersome. This can lead to the increase in false positive and true negative rates in print matching. In this paper, a method and system to extract forensic prints from any surface, irrespective of its shape, is presented. First, a suitable 3-D camera is used to capture images of the forensic print, and then the 3-D image is processed and unwrapped to obtain 2-D equivalent biometric prints. Computer simulations demonstrate the effectiveness of using 3-D technology for biometric matching of fingerprints, palm prints, and lip-prints. This system can be further extended to other biometric and non-biometric modalities.

  16. Technological process for production of persimmon and strawberry vinegars

    Directory of Open Access Journals (Sweden)

    Claudio Hidalgo

    2010-08-01

    Full Text Available Claudio Hidalgo1, Estibaliz Mateo1, Ana Belen Cerezo2, Maria-Jesús Torija1, Albert Mas11Biotecnologia Enològica, Departament de Bioquimica i Biotecnologia, Facultat d’Enologia, Universitat Rovira i Virgili, Marcel-li Domingo, Tarragona; 2Área de Nutrición y Bromatología, Facultad de Farmacia, Universidad de Sevilla, Sevilla, SpainAbstract: Fruit surplus is common in intensive agriculture in many countries. This ecologic and economic problem requires alternative uses to be found for fruit. The aim of this study was to use surplus fruit to produce vinegar by traditional methods (alcoholic fermentation and acetification from persimmon and strawberry. The process was performed with naturally occurring microorganisms and compared with inoculated commercial wine yeast for alcoholic fermentation. Alcoholic fermentation proceeded faster when inoculated due to the length of the lag phases observed in spontaneous fermentations. The alcoholic fermentations of strawberry mash were faster than those of persimmon mash. In contrast, acetifications were much faster in persimmon (30 days than in strawberry (70 days, in the latter some acetifications were not finished. From the technologic point of view, to produce persimmon and strawberry wine and vinegar, it is better to avoid fruit pressing and perform the process with fruit mash. Inoculation is recommended for persimmon and is necessary for strawberry.Keywords: wine, vinegar, fruit seasonings, acetic acid bacteria

  17. Acoustic monitoring of rotating machine by advanced signal processing technology

    International Nuclear Information System (INIS)

    Kanemoto, Shigeru

    2010-01-01

    The acoustic data remotely measured by hand held type microphones are investigated for monitoring and diagnosing the rotational machine integrity in nuclear power plants. The plant operator's patrol monitoring is one of the important activities for condition monitoring. However, remotely measured sound has some difficulties to be considered for precise diagnosis or quantitative judgment of rotating machine anomaly, since the measurement sensitivity is different in each measurement, and also, the sensitivity deteriorates in comparison with an attached type sensor. Hence, in the present study, several advanced signal processing methods are examined and compared in order to find optimum anomaly monitoring technology from the viewpoints of both sensitivity and robustness of performance. The dimension of pre-processed signal feature patterns are reduced into two-dimensional space for the visualization by using the standard principal component analysis (PCA) or the kernel based PCA. Then, the normal state is classified by using probabilistic neural network (PNN) or support vector data description (SVDD). By using the mockup test facility of rotating machine, it is shown that the appropriate combination of the above algorithms gives sensitive and robust anomaly monitoring performance. (author)

  18. Diamond MEMS: wafer scale processing, devices, and technology insertion

    Science.gov (United States)

    Carlisle, J. A.

    2009-05-01

    Diamond has long held the promise of revolutionary new devices: impervious chemical barriers, smooth and reliable microscopic machines, and tough mechanical tools. Yet it's been an outsider. Laboratories have been effectively growing diamond crystals for at least 25 years, but the jump to market viability has always been blocked by the expense of diamond production and inability to integrate with other materials. Advances in chemical vapor deposition (CVD) processes have given rise to a hierarchy of carbon films ranging from diamond-like carbon (DLC) to vapor-deposited diamond coatings, however. All have pros and cons based on structure and cost, but they all share some of diamond's heralded attributes. The best performer, in theory, is the purest form of diamond film possible, one absent of graphitic phases. Such a material would capture the extreme hardness, high Young's modulus and chemical inertness of natural diamond. Advanced Diamond Technologies Inc., Romeoville, Ill., is the first company to develop a distinct chemical process to create a marketable phase-pure diamond film. The material, called UNCD® (for ultrananocrystalline diamond), features grain sizes from 3 to 300 nm in size, and layers just 1 to 2 microns thick. With significant advantages over other thin films, UNCD is designed to be inexpensive enough for use in atomic force microscopy (AFM) probes, microelectromechanical machines (MEMS), cell phone circuitry, radio frequency devices, and even biosensors.

  19. Technological foundations of processing tomato pomace in feed additives

    Directory of Open Access Journals (Sweden)

    B. Yegorov

    2015-05-01

    Full Text Available Introduction. Search for new types of alternative raw material for the efficient development of poultry industry and problem of waste disposal of canning industry made it necessary to develop a method of processing tomato pomace in feed additives. Materials and methods. Sampling, preparation and testing were carried out by general and specific organ oleptic and physical-technological methods of assessment and analysis of the properties of raw materials and finished products. Results. Incorporation of tomato pomace in the feed additive reduces the cost of raw materials and expenses associated with moistening of the mixture before extrusion and incorporation of chalk feed will solve the problem of calcium imbalance of laying hens. It was found that extrusion process has improved the physical properties of feed additive and showed the possibility of its use as a feed component: moisture content decreased by 34.5 %, the angle of repose increased by 11.4 %, flowability decreased by 39.7 % and bulk density decreased by 32.3 %. Conclusions. The resulting feed additive will solve the problem of diversification of raw materials, waste, calcium imbalance of laying hens and reduce expenses on compound animal feedstuff production.

  20. THE ANALYSIS OF TECHNOLOGICAL PROCESS OF EXPEDITIONARY MAINTENANCE OF MOTOR TRANSPOR

    Directory of Open Access Journals (Sweden)

    V. S. Naumov

    2009-03-01

    Full Text Available The basic technological operations of the automobile freight forwarding process have been determined. The base algorithms of the freight forwarding technological process have been proposed. The fundamental flow charts of technological process in use have been formalized and analyzed.