WorldWideScience

Sample records for technology performance characteristics

  1. Distributed utility technology cost, performance, and environmental characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Y; Adelman, S

    1995-06-01

    Distributed Utility (DU) is an emerging concept in which modular generation and storage technologies sited near customer loads in distribution systems and specifically targeted demand-side management programs are used to supplement conventional central station generation plants to meet customer energy service needs. Research has shown that implementation of the DU concept could provide substantial benefits to utilities. This report summarizes the cost, performance, and environmental and siting characteristics of existing and emerging modular generation and storage technologies that are applicable under the DU concept. It is intended to be a practical reference guide for utility planners and engineers seeking information on DU technology options. This work was funded by the Office of Utility Technologies of the US Department of Energy.

  2. Characteristics and Performance of Existing Load Disaggregation Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Mayhorn, Ebony T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sullivan, Greg P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Butner, Ryan S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hao, He [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Baechler, Michael C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-04-10

    Non-intrusive load monitoring (NILM) or non-intrusive appliance load monitoring (NIALM) is an analytic approach to disaggregate building loads based on a single metering point. This advanced load monitoring and disaggregation technique has the potential to provide an alternative solution to high-priced traditional sub-metering and enable innovative approaches for energy conservation, energy efficiency, and demand response. However, since the inception of the concept in the 1980’s, evaluations of these technologies have focused on reporting performance accuracy without investigating sources of inaccuracies or fully understanding and articulating the meaning of the metrics used to quantify performance. As a result, the market for, as well as, advances in these technologies have been slowly maturing.To improve the market for these NILM technologies, there has to be confidence that the deployment will lead to benefits. In reality, every end-user and application that this technology may enable does not require the highest levels of performance accuracy to produce benefits. Also, there are other important characteristics that need to be considered, which may affect the appeal of NILM products to certain market targets (i.e. residential and commercial building consumers) and the suitability for particular applications. These characteristics include the following: 1) ease of use, the level of expertise/bandwidth required to properly use the product; 2) ease of installation, the level of expertise required to install along with hardware needs that impact product cost; and 3) ability to inform decisions and actions, whether the energy outputs received by end-users (e.g. third party applications, residential users, building operators, etc.) empower decisions and actions to be taken at time frames required for certain applications. Therefore, stakeholders, researchers, and other interested parties should be kept abreast of the evolving capabilities, uses, and characteristics

  3. Performance Characteristics and Temperature Compensation Method of Fluid Property Sensor Based on Tuning-Fork Technology

    Directory of Open Access Journals (Sweden)

    Yuan Chen

    2016-01-01

    Full Text Available Fluid property sensor (FPS based on tuning-fork technology is applied to the measurement of the contaminant level of lubricant oil. The measuring principle of FPS sensor is derived and proved together with its resolution. The performance characteristics of the FPS sensor, such as sensitivity coefficient, resolution, and quality factor, are analyzed. A temperature compensation method is proposed to eliminate the temperature-dependence of the measuring parameters, and its validity is investigated by numerical simulation of sensitivity, oscillating frequency, and dielectric constant. The values of purification efficiency obtained using microwave and without microwave are compared experimentally.

  4. Performance characteristics of the 12 GHz, 200 watt Transmitter Experiment Package for CTS. [Communication Technology Satellite

    Science.gov (United States)

    Miller, E. F.; Fiala, J. L.; Hansen, I. G.

    1975-01-01

    Measured performance characteristics from ground test of the Transmitter Experiment Package (TEP) for the Communications Technology Satellite are presented. The experiment package consists of a 200 W Output Stage Tube (OST) powered by a Power Processing System (PPS). Descriptions of both the PPS and OST are given. The PPS provides the necessary voltages with a measured dc/dc conversion efficiency of 89 per cent. The OST, a traveling wave tube with multiple collectors, has a saturated rf output power of 224 W and operates at an overall efficiency exceeding 40 per cent over an 85 MHz bandwidth at 12 GHz. OST performance given includes frequency response, saturation characteristics, group delay, AM to PM conversion, intermodulation distortion, and two channel gain suppression. Single and dual channel FM video performance is presented. It was determined that for 12 MHz peak to peak frequency deviation on each channel, dual channel FM television signals can be transmitted through the TEP at 60 W, each channel, with 40 MHz channel spacing (center to center).

  5. Performance and touch characteristics of disabled and non-disabled participants during a reciprocal tapping task using touch screen technology.

    Science.gov (United States)

    Irwin, Curt B; Sesto, Mary E

    2012-11-01

    Touch screens are becoming more prevalent in everyday environments. Therefore, it is important that this technology is accessible to those with varying disabilities. The objective of the current study was to evaluate performance and touch characteristics (forces, impulses, and dwell times) of individuals with and without a movement disorder during a reciprocal tapping touch screen task. Thirty-seven participants with a motor control disability and 15 non-disabled participants participated. Outcome measures include number of correct taps, dwell time, exerted force, and impulse. Results indicate non-disabled participants had 1.8 more taps than participants with fine motor control disabilities and 2.8 times more than those with gross motor impairments (ptouch characteristics exist between those with and without motor control disabilities. Understanding how people (including those with disabilities) interact with touch screens may allow designers and engineers to ultimately improve usability of touch screen technology. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  6. Performance characteristics of shape memory alloy and its applications for fusion technology

    International Nuclear Information System (INIS)

    Nishikawa, Masahiro; Watanabe, Kenji

    1987-01-01

    As a shape memory alloy, Au-Cd alloy was found in 1951. Thereafter, also in In-Tl alloy, shape memory effect was found. The U.S. Naval Ordinance Laboratory developed Ni-Ti alloy, and published in 1965 as NITINOL. As Cu group shape memory alloys, there are Cu-Zn-Al alloy, Cu-Al-Be alloy and Cu-Al-Ni alloy. Recently, iron group shape memory alloy was published. In 1975, 'Shape memory effect and its application' symposium, in 1978, 'NITINOL heat engine international conference', and in 1982 and 1986, 'Martensite transformation international conference' were held, and the method of the proper use of shape memory alloys and the problems of the alloys themselves such as fatigue have been gradually clarified. In this report, the fundamental action characteristics of shape memory alloys are discribed from the viewpoint of the application, and the possibility of applying these characteristics to nuclear fusion devices and the advantage obtained as the result are explained. Shape memory effect and pseudo-elasticity, reversible shape memory effect, the thermodynamic behavior of shape memory alloys, transformation temperature range and using temperature range and so on are described. (Kako, I.)

  7. Technological characteristics of meat - viscosity

    OpenAIRE

    DIBĎÁK, Tomáš

    2012-01-01

    This bachelor thesis is focused on the technological characteristics of meat, mainly viscosity of meat. At the beginning I dealt with construction of meat and various types of meat: beef, veal, pork, mutton, rabbit, poultry and venison. Then I described basic chemical composition of meat and it?s characteristic. In detail I dealt with viscosity of meat. Viscosity is the ability of meat to bind water both own and added. I mentioned influences, which effects viscosity and I presented the possib...

  8. Technology Performance Level Assessment Methodology.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Jesse D.; Bull, Diana L; Malins, Robert Joseph; Costello, Ronan Patrick; Aurelien Babarit; Kim Nielsen; Claudio Bittencourt Ferreira; Ben Kennedy; Kathryn Dykes; Jochem Weber

    2017-04-01

    The technology performance level (TPL) assessments can be applied at all technology development stages and associated technology readiness levels (TRLs). Even, and particularly, at low TRLs the TPL assessment is very effective as it, holistically, considers a wide range of WEC attributes that determine the techno-economic performance potential of the WEC farm when fully developed for commercial operation. The TPL assessment also highlights potential showstoppers at the earliest possible stage of the WEC technology development. Hence, the TPL assessment identifies the technology independent “performance requirements.” In order to achieve a successful solution, the entirety of the performance requirements within the TPL must be considered because, in the end, all the stakeholder needs must be achieved. The basis for performing a TPL assessment comes from the information provided in a dedicated format, the Technical Submission Form (TSF). The TSF requests information from the WEC developer that is required to answer the questions posed in the TPL assessment document.

  9. State of the art of NOx mitigation technologies and their effect on the performance and emission characteristics of biodiesel-fueled Compression Ignition engines

    International Nuclear Information System (INIS)

    Palash, S.M.; Masjuki, H.H.; Kalam, M.A.; Masum, B.M.; Sanjid, A.; Abedin, M.J.

    2013-01-01

    Highlights: • Different NO x reduction technologies are discussed along with their implementation. • EGR rate up to 25% is feasible considering engine performance and other emissions. • ITR technology reduces NO x fairly but increases other emissions, it also reduces performance. • LTC reduces NO x and PM emissions simultaneously but increases HC and CO emissions. • Water injection and emulsion reduce NO x (up to 38%) and PM but increases HC and CO emissions. - Abstract: Biodiesel fuels have the potential to become a reliable substitute for diesel which is used moderately to meet the current energy demands. This fuel can be produced from new or used vegetable oils, non-edible sources and animal fats, which are non-toxic, biodegradable and renewable. In spite of the many advantages of using biodiesel, most of the researchers have reported that they produce higher NO x emissions compared to diesel, which is a deterrent to the market expansion of these fuels. In this study, the different paths to reduce NO x emissions from diesel engines by applying several technologies, such as using additives into fuel, exhaust gas recirculation (EGR), water injection (WI), emulsion technology (ET), injection timing retardation (ITR), simultaneous technology (ST) and low temperature combustion (LTC) mode are reviewed briefly. The impacts of different NO x mitigation technologies on biodiesel-fueled diesel engine performance and emissions are also analyzed critically and different methods of their implementation are shown. This paper also provides a comparison of different NO x mitigation technologies based on previous articles related to this topic. From this comparative study, it was found that the average reduction of NO x emissions by using additives, EGR, WI and ET, ITR, ST and LTC are in the ranges 4–45%, 26–84%, 10–38%, 9.77–37%, 22–95% and 66–93% respectively, compared to biodiesel combustion without applying technologies. However, the average reduction

  10. Technological Capability and Firm Performance

    Directory of Open Access Journals (Sweden)

    Fernanda Maciel Reichert

    2014-08-01

    Full Text Available This research aims to investigate the relationship between investments in technological capability and economic performance in Brazilian firms. Based on economic development theory and on developed countries history, it is assumed that this relationship is positive. Through key indicators, 133 Brazilian firms have been analyzed. Given the economic circumstances of an emerging economy, which the majority of businesses are primarily based on low and medium-low-technology industries, it is not possible to affirm the existence of a positive relation between technological capability and firm performance. There are other elements that allow firms to achieve such results. Firms of lower technological intensity industries performed above average in the economic performance indicators, adversely, they invested below average in technological capability. These findings do not diminish the merit of firms’ and country’s success. They in fact confirm a historical tradition of a country that concentrates its efforts on basic industries.

  11. Advanced fuel technology and performance

    International Nuclear Information System (INIS)

    1985-10-01

    The purpose of the Advisory Group Meeting on Advanced Fuel Technology and Performance was to review the experience of advanced fuel fabrication technology, its performance, peculiarities of the back-end of the nuclear fuel cycle with regard to all types of reactors and to outline the future trends. As a result of the meeting recommendations were made for the future conduct of work on advanced fuel technology and performance. A separate abstract was prepared for each of the 20 papers in this issue

  12. Developing countries SMEs innovation characteristics and performance

    DEFF Research Database (Denmark)

    Vang, Jan; Rezaei, Shahamak; Baklanov, Nikita

    An econometric study analysing developing countries’ SMEs innovation characteristics and their correlation with performance.......An econometric study analysing developing countries’ SMEs innovation characteristics and their correlation with performance....

  13. High performance fuel technology development

    Energy Technology Data Exchange (ETDEWEB)

    Koon, Yang Hyun; Kim, Keon Sik; Park, Jeong Yong; Yang, Yong Sik; In, Wang Kee; Kim, Hyung Kyu [KAERI, Daejeon (Korea, Republic of)

    2012-01-15

    {omicron} Development of High Plasticity and Annular Pellet - Development of strong candidates of ultra high burn-up fuel pellets for a PCI remedy - Development of fabrication technology of annular fuel pellet {omicron} Development of High Performance Cladding Materials - Irradiation test of HANA claddings in Halden research reactor and the evaluation of the in-pile performance - Development of the final candidates for the next generation cladding materials. - Development of the manufacturing technology for the dual-cooled fuel cladding tubes. {omicron} Irradiated Fuel Performance Evaluation Technology Development - Development of performance analysis code system for the dual-cooled fuel - Development of fuel performance-proving technology {omicron} Feasibility Studies on Dual-Cooled Annular Fuel Core - Analysis on the property of a reactor core with dual-cooled fuel - Feasibility evaluation on the dual-cooled fuel core {omicron} Development of Design Technology for Dual-Cooled Fuel Structure - Definition of technical issues and invention of concept for dual-cooled fuel structure - Basic design and development of main structure components for dual- cooled fuel - Basic design of a dual-cooled fuel rod.

  14. Integrating Human Performance and Technology

    International Nuclear Information System (INIS)

    Farris, Ronald K.; Medema, Heather

    2012-01-01

    Human error is a significant factor in the cause and/or complication of events that occur in the commercial nuclear industry. In recent years, great gains have been made using Human Performance (HU) tools focused on targeting individual behaviors. However, the cost of improving HU is growing and resistance to add yet another HU tool certainly exists, particularly for those tools that increase the paperwork for operations. Improvements in HU that are the result of leveraging existing technology, such as hand-held mobile technologies, have the potential to reduce human error in controlling system configurations, safety tag-outs, and other verifications. Operator rounds, valve lineup verifications, containment closure verifications, safety and equipment protection, and system tagging can be supported by field-deployable wireless technologies. These devices can also support the availability of critical component data in the main control room and other locations. This research pilot project reviewing wireless hand-held technology is part of the Light Water Reactor Sustainability Program (LWRSP), a research and development (R and D) program sponsored by the U. S. Department of Energy (DOE). The project is being performed in close collaboration with industry R and D programs to provide the technical foundations for licensing, and managing the long-term, safe, and economical operation of current nuclear power plants. The LWRSP vision is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current nuclear reactor fleet. (author)

  15. Integrating Human Performance and Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ronald K. Farris; Heather Medema

    2012-05-01

    Human error is a significant factor in the cause and/or complication of events that occur in the commercial nuclear industry. In recent years, great gains have been made using Human Performance (HU) tools focused on targeting individual behaviors. However, the cost of improving HU is growing and resistance to add yet another HU tool certainly exists, particularly for those tools that increase the paperwork for operations. Improvements in HU that are the result of leveraging existing technology, such as hand-held mobile technologies, have the potential to reduce human error in controlling system configurations, safety tag-outs, and other verifications. Operator rounds, valve line-up verifications, containment closure verifications, safety & equipment protection, and system tagging can be supported by field-deployable wireless technologies. These devices can also support the availability of critical component data in the main control room and other locations. This research pilot project reviewing wireless hand-held technology is part of the Light Water Reactor Sustainability Program (LWRSP), a research and development (R&D) program sponsored by the U. S. Department of Energy (DOE). The project is being performed in close collaboration with industry R&D programs to provide the technical foundations for licensing, and managing the long-term, safe, and economical operation of current nuclear power plants. The LWRSP vision is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current nuclear reactor fleet.

  16. Environmental characteristics of clean coal technologies

    International Nuclear Information System (INIS)

    Bossart, S.J.

    1992-01-01

    The Department of Energy's (DOE) Clean Coal Technology (CCT) Program is aimed at demonstrating the commercial readiness of advanced coal-based technologies. A major goal of the CCT program is to introduce into the US energy marketplace those coal-based power generation technologies that have superior economic and environmental performance over the current suite of commercial coal-based power generation technologies. The commercialization of CCTs will provide the electric utility industry with technology options for replacing aging power plants and meeting future growth in electricity demand. This paper discusses the environmental advantages of two CCTs used for electric power generation: pressurized fluidized-bed combustion (PFBC) and integrated gasification combined-cycle (IGCC). These CCTs are suitable for repowering existing power plants or for grassroots construction. Due to their high efficiency and advanced environmental control systems, they emit less sulfur dioxide (SO 2 ), nitrogen oxides (NO x ), particulate matter, and carbon dioxide (CO 2 ) than a state-of-the-art, pulverized coal power plant with flue gas desulfurization (PC/FGD)

  17. Board characteristics, governance objectives, and hospital performance

    DEFF Research Database (Denmark)

    Thiel, Andrea; Winter, Vera; Büchner, Vera Antonia

    2018-01-01

    membership relates to board characteristics and financial performance. METHODOLOGY: Using factor analysis, we identify latent classes of governance objectives and use hierarchical cluster analysis to detect distinct clusters with varying emphasis on the classes. We then use multinomial regression to explore...... the associations between cluster membership and board characteristics (size, gender diversity, and occupational diversity) and examine the associations between clusters and financial performance using OLS regression. RESULTS: Classes of objectives reflecting three governance theories-agency theory, stewardship...... and hospital financial performance, with two of three groups performing significantly better than the reference group. CONCLUSION: High performance in hospitals can be the result of governance logics, which, compared to simple board characteristics, are associated with better financial outcomes. PRACTICE...

  18. Growth performance, carcass and hematological characteristics of ...

    African Journals Online (AJOL)

    Growth performance, carcass and hematological characteristics of rabbits fed graded levels of tiger nuts ( Cyperus esculentus ) ... (p>0.05) difference between treatments. Results demonstrated that (Cyperus esculentus) could be used up to 5% in rabbit's diets without adverse effect on the animals' performance and health.

  19. How does technological regime affect performance of technology development projects?

    NARCIS (Netherlands)

    Song, Michael; Hooshangi, Soheil; Zhao, Y. Lisa; Halman, Johannes I.M.

    2014-01-01

    In this study, we examine how technological regime affects the performance of technology development projects (i.e., project quality, sales, and profit). Technological regime is defined as the set of attributes of a technological environment where the innovative activities of firms take place.

  20. Thermic diode performance characteristics and design manual

    Science.gov (United States)

    Bernard, D. E.; Buckley, S.

    1979-01-01

    Thermic diode solar panels are a passive method of space and hot water heating using the thermosyphon principle. Simplified methods of sizing and performing economic analyses of solar heating systems had until now been limited to passive systems. A mathematical model of the thermic diode including its high level of stratification has been constructed allowing its performance characteristics to be studied. Further analysis resulted in a thermic diode design manual based on the f-chart method.

  1. Haematological characteristics and performance of West African ...

    African Journals Online (AJOL)

    The effects of feeding crude petroleum contaminated forage on haematological characteristics and performance of 36 young West African Dwarf (WAD) goats was investigated in order to simulate the impact of real crude oil spillage on livestock and game. Graded levels (0.0, 1.5 and 3.0 g per kg forage) of stabilized “Bonny ...

  2. Growth performance, blood parameters and carcass characteristics ...

    African Journals Online (AJOL)

    This study was carried out with one hundred and twenty (120) day-old marshal chicks to investigate the effect of Maxigrain® enzyme supplementation of corn bran based diets on growth performance, carcass characteristics, haematology and serum biochemistry of broilers in an eight weeks experiment. Four experimental ...

  3. Development of Integrated Assessment Technology of Risk and Performance

    International Nuclear Information System (INIS)

    Yang, Jun Eon; Kang, Dae Il; Kang, Hyun Gook

    2010-04-01

    The main idea and contents are summarized as below 1) Development of new risk/performance assessment system innovating old labor-intensive risk assessment structure - New consolidated risk assessment technology from various hazard(flood, fire, seismic in NPP) - BOP model development for performance monitoring - Consolidated risk/performance management system for consistency and efficiency of NPP 2) Resolution technology for pending issues in PSA - Base technology for PSA of digital I and C system - Base technology for seismic PSA reflecting domestic seismic characteristics and aging effect - Uncertainty reduction technology for level 2 PSA and best estimation of containment failure frequency 3) Next generation risk/performance assessment technology - Human-induced error reduction technology for efficient operation of a NPP

  4. Ceramic PPC technology and performance

    International Nuclear Information System (INIS)

    Akimov, V.; Arefiev, A.; Bizzeti, A.; Civinini, C.; Choumilov, E.; Alessandro, R. d'; Ferrando, A.; Kolotaev, Y.; Kuleshov, S.; Malinin, A.; Martemianov, A.; Martinez-Laso, L.; Mikhailov, K.; Pojidaev, V.; Rojkov, A.; Serov, V.; Smirnitsky, A.

    1994-01-01

    Mass production technology for PCCs (Parallel Plate Chambers) is described. This technology provides a precise manufacture of chamber components and a high uniformity of chamber properties. Only radiation hard materials were used. Results on the chamber uniformity, the detection efficiency and the timing properties of PPCs are presented. (orig.)

  5. Populações de milho: características agronômicas e tecnológicas Maize populations performance as to agronomic and technological characteristics

    Directory of Open Access Journals (Sweden)

    Marlene Lima

    1988-01-01

    Full Text Available Avaliaram-se duas populações de milho de grãos brancos (IAC-Taitinga e IAC-Moroti e duas de grãos amarelos (IAC-Taiúba e IAC-Iubatã e os cruzamentos recíprocos entre as de grãos brancos e três testemunhas (Ag-401, C-601 e IAC-Porangatu, em dois locais, quanto a características agronômicas. Com exceção das testemunhas, testaram-se também tais populações quanto aos principais parâmetros de interesse tecnológico, relacionados com o rendimento e qualidade do fubá mimoso, para uso em panificação. Foram observadas diferenças altamente significativas entre os tratamentos para os caracteres produtividade de grãos, altura da planta e de inserção da espiga, rendimento de gérmen e de fubá mimoso, volume específico comparativo (V.E.C. e escore total comparativo (Es. T.C.. As populações, de modo geral, apresentaram altos níveis de produção de grãos, sendo o maior valor obtido pela população IAC-Taitinga. Sete dos materiais estudados apresentaram porte médio e dois, porte baixo. A população IAC Taitinga, sem diferir de IAC-Moroti e do híbrido IAC-Taitinga x IAC Moroti, apresentou o maior valor para rendimento de fubá mimoso. A IAC-Taiúba sobressaiu-se das demais quanto ao V.E.C. e só não alcançou valor máximo para Es.T.C. devido à cor amarela dos grãos. A IAC-Taitinga e o híbrido IAC-Taitinga x IAC-Moroti mostraram valores iguais ao padrão (100% para Es.T.C. Foi observado efeito maternal atuando no rendimento do fubá mimoso obtido.White and yellow grained maize populations and some of their reciprocal crosses were evaluated as to several agronomic traits as well as to flour yield and bread characteristics. Some populations, including the hybrids under testing showed high grain yield potentials, at the same levels of commercial hybrids Ag-401 e C-601. Significant differences were recorded for plant and ear height, among the entries studied. 'IAC-Taitinga', without differing- from 'IAC-Moroti' and 'IAC

  6. Evaluating Technology Resistance and Technology Satisfaction on Students' Performance

    Science.gov (United States)

    Norzaidi, Mohd Daud; Salwani, Mohamed Intan

    2009-01-01

    Purpose: Using the extended task-technology fit (TTF) model, this paper aims to examine technology resistance, technology satisfaction and internet usage on students' performance. Design/methodology/approach: The study was conducted at Universiti Teknologi MARA, Johor, Malaysia and questionnaires were distributed to 354 undergraduate students.…

  7. Relationships between Teacher Characteristics and Educational Technology

    Science.gov (United States)

    Schulze, Kurt Ronald

    2014-01-01

    Too often, teachers are using educational technology resources for administrative purposes instead of using these resources in a constructivist manner to enhance student learning. The study site was well behind the national average in overall educational technology use categories. The purpose of this explanatory correlational research was to…

  8. Technology in Paralympic sport: performance enhancement or essential for performance?

    Science.gov (United States)

    Burkett, Brendan

    2010-02-01

    People with disabilities often depend on assistive devices to enable activities of daily living as well as to compete in sport. Technological developments in sport can be controversial. To review, identify and describe current technological developments in assistive devices used in the summer Paralympic Games; and to prepare for the London 2012 Games, the future challenges and the role of technology are debated. A systematic review of the peer-reviewed literature and personal observations of technological developments at the Athens (2004) and Beijing (2008) Paralympic Games was conducted. Standard assistive devices can inhibit the Paralympians' abilities to perform the strenuous activities of their sports. Although many Paralympic sports only require technology similar to their Olympic counterparts, several unique technological modifications have been made in prosthetic and wheelchair devices. Technology is essential for the Paralympic athlete, and the potential technological advantage for a Paralympian, when competing against an Olympian, is unclear. Technology must match the individual requirements of the athlete with the sport in order for Paralympians to safely maximise their performance. Within the 'performance enhancement or essential for performance?' debate, any potential increase in mechanical performance from an assistive device must be considered holistically with the compensatory consequences the disability creates. To avoid potential technology controversies at the 2012 London Olympic and Paralympic Games, the role of technology in sport must be clarified.

  9. Characteristics and performances of electronic personal dosemeters

    International Nuclear Information System (INIS)

    Aubert, B.

    2002-01-01

    The regulations have made obligation for 2 years to measure and analyse the amounts of radiations actually received during an operation. The whole of these measurements taken uninterrupted for an immediate reading is indicated like the operational dosimetry, which is carried out with the means of personal electronic dosemeters. This study analyses the legislation relating to this type of dosimetry as well as the requirements in medical environment, and presents an assessment of the characteristics and performances of the devices available on the French market at the beginning of 2002 starting from the information provided by the various manufacturers. (author)

  10. Cooperation, Technology, and Performance: A Case Study.

    Science.gov (United States)

    Cavanagh, Thomas; Dickenson, Sabrina; Brandt, Suzanne

    1999-01-01

    Describes the CTP (Cooperation, Technology, and Performance) model and explains how it is used by the Department of Veterans Affairs-Veteran's Benefit Administration (VBA) for training. Discusses task analysis; computer-based training; cooperative-based learning environments; technology-based learning; performance-assessment methods; courseware…

  11. Characteristics explaining performance in downhill mountain biking.

    Science.gov (United States)

    Chidley, Joel B; MacGregor, Alexandra L; Martin, Caoimhe; Arthur, Calum A; Macdonald, Jamie H

    2015-03-01

    To identify physiological, psychological, and skill characteristics that explain performance in downhill (DH) mountain-bike racing. Four studies were used to (1) identify factors potentially contributing to DH performance (using an expert focus group), (2) develop and validate a measure of rider skill (using video analysis and expert judge evaluation), (3) evaluate whether physiological, psychological, and skill variables contribute to performance at a DH competition, and (4) test the specific contribution of aerobic capacity to DH performance. STUDY 1 identified aerobic capacity, handgrip endurance, anaerobic power, rider skill, and self-confidence as potentially important for DH. In study 2 the rider-skill measure displayed good interrater reliability. Study 3 found that rider skill and handgrip endurance were significantly related to DH ride time (β=-0.76 and -0.14, respectively; R2=.73), with exploratory analyses suggesting that DH ride time may also be influenced by self-confidence and aerobic capacity. Study 4 confirmed aerobic capacity as an important variable influencing DH performance (for a DH ride, mean oxygen uptake was 49±5 mL·kg(-1)·min(-1), and 90% of the ride was completed above the 1st ventilatory threshold). In order of importance, rider skill, handgrip endurance, self-confidence, and aerobic capacity were identified as variables influencing DH performance. Practically, this study provides a novel assessment of rider skill that could be used by coaches to monitor training and identify talent. Novel intervention targets to enhance DH performance were also identified, including self-confidence and aerobic capacity.

  12. Technological Innovation Capabilities and Firm Performance

    OpenAIRE

    Richard C.M. Yam; William Lo; Esther P.Y. Tang; Antonio; K.W. Lau

    2010-01-01

    Technological innovation capability (TIC) is defined as a comprehensive set of characteristics of a firm that facilities and supports its technological innovation strategies. An audit to evaluate the TICs of a firm may trigger improvement in its future practices. Such an audit can be used by the firm for self assessment or third-party independent assessment to identify problems of its capability status. This paper attempts to develop such an auditing framework that can...

  13. Technology Leadership in Malaysia's High Performance School

    Science.gov (United States)

    Yieng, Wong Ai; Daud, Khadijah Binti

    2017-01-01

    Headmaster as leader of the school also plays a role as a technology leader. This applies to the high performance schools (HPS) headmaster as well. The HPS excel in all aspects of education. In this study, researcher is interested in examining the role of the headmaster as a technology leader through interviews with three headmasters of high…

  14. A review of hospital characteristics associated with improved performance.

    Science.gov (United States)

    Brand, Caroline A; Barker, Anna L; Morello, Renata T; Vitale, Michael R; Evans, Sue M; Scott, Ian A; Stoelwinder, Johannes U; Cameron, Peter A

    2012-10-01

    The objective of this review was to critically appraise the literature relating to associations between high-level structural and operational hospital characteristics and improved performance. The Cochrane Library, MEDLINE (Ovid), CINAHL, proQuest and PsychINFO were searched for articles published between January 1996 and May 2010. Reference lists of included articles were reviewed and key journals were hand searched for relevant articles. and data extraction Studies were included if they were systematic reviews or meta-analyses, randomized controlled trials, controlled before and after studies or observational studies (cohort and cross-sectional) that were multicentre, comparative performance studies. Two reviewers independently extracted data, assigned grades of evidence according to the Australian National Health and Medical Research Council guidelines and critically appraised the included articles. Data synthesis Fifty-seven studies were reported within 12 systematic reviews and 47 observational articles. There was heterogeneity in use and definition of performance outcomes. Hospital characteristics investigated were environment (incentives, market characteristics), structure (network membership, ownership, teaching status, geographical setting, service size) and operational design (innovativeness, leadership, organizational culture, public reporting and patient safety practices, information technology systems and decision support, service activity and planning, workforce design, staff training and education). The strongest evidence for an association with overall performance was identified for computerized physician order entry systems. Some evidence supported the associations with workforce design, use of financial incentives, nursing leadership and hospital volume. There is limited, mainly low-quality evidence, supporting the associations between hospital characteristics and healthcare performance. Further characteristic-specific systematic reviews are

  15. Performance Evaluation Methods for Assistive Robotic Technology

    Science.gov (United States)

    Tsui, Katherine M.; Feil-Seifer, David J.; Matarić, Maja J.; Yanco, Holly A.

    Robots have been developed for several assistive technology domains, including intervention for Autism Spectrum Disorders, eldercare, and post-stroke rehabilitation. Assistive robots have also been used to promote independent living through the use of devices such as intelligent wheelchairs, assistive robotic arms, and external limb prostheses. Work in the broad field of assistive robotic technology can be divided into two major research phases: technology development, in which new devices, software, and interfaces are created; and clinical, in which assistive technology is applied to a given end-user population. Moving from technology development towards clinical applications is a significant challenge. Developing performance metrics for assistive robots poses a related set of challenges. In this paper, we survey several areas of assistive robotic technology in order to derive and demonstrate domain-specific means for evaluating the performance of such systems. We also present two case studies of applied performance measures and a discussion regarding the ubiquity of functional performance measures across the sampled domains. Finally, we present guidelines for incorporating human performance metrics into end-user evaluations of assistive robotic technologies.

  16. Biological and technological characteristics of Georgian wine and table grapes

    Directory of Open Access Journals (Sweden)

    Ujmajuridze Levan

    2015-01-01

    Description of grapevine varieties implemented through the descriptors for grapevine (IPGRI OIV. Botanical, biological-technological, qualitative and quantitative marks are characterized and evaluated. Investigation conducted during the biologic development phases were studied for chemical and eno-carpological characteristics.

  17. Designing and Implementing Performance Technology for Teachers

    Directory of Open Access Journals (Sweden)

    Joi L. Moore

    2004-06-01

    Full Text Available This paper synthesizes research findings from a performance analysis of teacher tasks and the implementation of performance technology. These findings are aligned with design and implementation theories to provide understanding of the complex factors and events that occur during the implementation process. The article describes the necessary elements and conditions for designing and implementing performance tools in school environments that will encourage usage, efficient performance, and positive attitudes. Two models provide a visual representation of causal relationships between the implementation factors and the technology user. Although the implementation process can become complex because of the simultaneous events and phases, it can be properly managed through good communication and strategic involvement of teachers during the design and development process. The models may be able to assist technology designers and advocates with presenting innovations to teachers who are frequently asked to try technical solutions for performance support or improvement.

  18. The Characteristics of a Model Technology Education Teacher

    Science.gov (United States)

    Kaufman, Andrew R.; Warner, Scott A.; Buechele, Jessica R.

    2011-01-01

    The things that make the quality of a teacher stand out can cover a wide range of characteristics, actions, words, and experiences. The mark left on a student by a teacher, for good or bad, is written in an ink that will last a lifetime. This article describes a study that identifies the characteristics of exceptional technology education…

  19. Load Disaggregation Technologies: Real World and Laboratory Performance

    Energy Technology Data Exchange (ETDEWEB)

    Mayhorn, Ebony T.; Sullivan, Greg P.; Petersen, Joseph M.; Butner, Ryan S.; Johnson, Erica M.

    2016-09-28

    Low cost interval metering and communication technology improvements over the past ten years have enabled the maturity of load disaggregation (or non-intrusive load monitoring) technologies to better estimate and report energy consumption of individual end-use loads. With the appropriate performance characteristics, these technologies have the potential to enable many utility and customer facing applications such as billing transparency, itemized demand and energy consumption, appliance diagnostics, commissioning, energy efficiency savings verification, load shape research, and demand response measurement. However, there has been much skepticism concerning the ability of load disaggregation products to accurately identify and estimate energy consumption of end-uses; which has hindered wide-spread market adoption. A contributing factor is that common test methods and metrics are not available to evaluate performance without having to perform large scale field demonstrations and pilots, which can be costly when developing such products. Without common and cost-effective methods of evaluation, more developed disaggregation technologies will continue to be slow to market and potential users will remain uncertain about their capabilities. This paper reviews recent field studies and laboratory tests of disaggregation technologies. Several factors are identified that are important to consider in test protocols, so that the results reflect real world performance. Potential metrics are examined to highlight their effectiveness in quantifying disaggregation performance. This analysis is then used to suggest performance metrics that are meaningful and of value to potential users and that will enable researchers/developers to identify beneficial ways to improve their technologies.

  20. Photovoltaic technology, performance, manufacturing cost and markets

    International Nuclear Information System (INIS)

    Maycock, P.D.

    1999-01-01

    A comprehensive discussion of key aspects of photovoltaic energy conversion systems will provide the basis for forecasting PV module shipments from 1999 to 2010. Principal areas covered include: (1) Technology and Performance Status: The module efficiency and performance are described for commercial cell technologies including single crystal silicon, polycrystal silicon, ribbon silicon, film silicon on low cost substrate, amorphous silicon, copper indium diselenide, and cadmium telluride; (2) Manufacturing cost: 1999 costs for PV technologies in production (single crystal silicon, polycrystal silicon, and amorphous silicon) are developed. Manufacturing costs for 10--25 MW plants and 100 MW plants will be estimated; (3) The world PV market is summarized by region, top ten companies, and technology; and (4) Forecast of the World Market (seven market sectors) to 2010 will be presented. Key assumptions, price of modules, incentive programs, price of competing electricity generation will be detailed

  1. Nanotechnological inventions considerably improve performance characteristics

    Directory of Open Access Journals (Sweden)

    VLASOV Vladimir Alexeevich

    2014-06-01

    Full Text Available The invention «The method of production of carbon nanomaterial (RU 2509053» can be used as an additive for concretes and polymers which significantly improves their performance characteristics. The method of production of carbon nanomaterial consists of the following stages: preliminary preparation of sphagnous moss when it is refined from foreign admixtures, dried up to 10% humidity and ground, then ground material is exposed to pyrolysis under the temperature 850–950оC for 1–2 hours and cooled up to the environment temperature. After that amorphous carbon obtained in pyrolysis is treated with mechanical activation in the variable planetary mill for 7–10 hours. The invention makes it possible to provide increased outcome of nanotubes with high cleanliness. The invention «The method of production of nanodispersed metal powders and alloys of them (RU 2509626» relates to the powder metallurgy. Powder metal chloride or powder mixture at least of two metal chlorides is treated in the environment of the water steam which is supplied in reaction space at the rate of 50–100 ml/min at the temperature 400–800оC at the presence of absorbent carbon or introducing carbon oxide (II obtained during dissolution of formic acid HCOOH. The invention provides reliable production of nanodispersed metal powders and alloys of them from 3-d metal range: Ni, Co, Cu, Fe, Zn which can be used in powder metallurgy to improve baking process, in chemical industry as the fillers of polymers and reaction catalysts; as additives to anticorrosive covers, etc.

  2. Recent technology on steam turbine performance improvement

    International Nuclear Information System (INIS)

    Hirada, M.; Watanabe, E.; Tashiro, H.

    1991-01-01

    Continuous efforts have been made to improve turbine efficiency by applying the latest aerodynamic technologies to meet the energy saving requirement. In recent years, there has been considerable improvement in the field of computational fluid dynamics and these new technologies have been applied to the new blade design for HP, IP and LP turbines. Experimental verification for the new blade in turbine tests has established the overall turbine performance improvement and the excellent correspondence of flow pattern to the predicted value. This paper introduces the latest design technologies for the newly developed high efficiency blade and the verification test results

  3. Design and performance characteristics of an electromagnetic ...

    Indian Academy of Sciences (India)

    in many scientific and technological applications like extraction of a single pulse from a ... of laser systems involving one or several electro optic switches. 2. ... of any barrier is a measure of its ability to control radiated electro-magnetic energy.

  4. Destination Characteristics that Drive Hotel Performance

    DEFF Research Database (Denmark)

    Assaf, A. George; Josiassen, Alexander; Woo, Linda

    2017-01-01

    , government support, disposable income, and number of international arrivals within a tourism destination. Results indicate that the most important barriers to hotel performance are the competition among accommodation providers, tax rate and fuel price. We argue for the need for hotel providers to develop......The increased market saturation and competition in both domestic and international tourism destinations have renewed interest among hotel operators in identifying the key drivers of hotel performance. This paper presents a comprehensive analysis of the determinants of hotel performance...... strategies that take cognisance of the key drivers and barriers to enhancing hotel performance in an ever-changing global tourism sector....

  5. Materials performance in advanced fossil technologies

    International Nuclear Information System (INIS)

    Natesan, K.

    1991-01-01

    A number of advanced technologies are being developed to convert coal into clean fuels for use as a feedstock in chemical plants and for power generation. From the standpoint of component materials, the environments created by coal conversion and combustion in these technologies and their interactions with materials are of interest. This article identifies several modes of materials degradation and possible mechanisms for metal wastage. Available data on the performance of materials in several of the environments are highlighted, and examples of promising research activities to improve the corrosion resistance of materials are presented

  6. Cost and performance of innovative remediation technologies

    International Nuclear Information System (INIS)

    Cummings, J.B.; Kingscott, J.W.; Fiedler, L.D.

    1995-01-01

    The selection and use of more cost-effective remedies requires better access to data on the performance and cost of technologies used in the field. To make data more widely available, the US Environmental Protection Agency is working jointly with member agencies of the Federal Remediation Technologies Round table to publish case studies of full-scale remediation and demonstration projects. EPA, DoD, and DOE have published case studies of cleanup projects primarily consisting of bioremediation, soil vapor extraction, and thermal desorption. Within the limits of this initial data set, the paper evaluates technology performance and cost. In the analysis of cost factors, the paper shows the use of a standardized Work Breakdown Structure (WBS). Use of the WBS will be important in future reporting of completed projects to facilitate cost comparison. The paper notes the limits to normalization and thus cross-site comparison which can be achieved using the WBS. The paper identifies conclusions from initial efforts to compile cost and performance data, highlights the importance of such efforts to the overall remediation effort, and discusses future cost and performance documentation efforts

  7. Haematological characteristics and performance of West African ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-02-18

    Feb 18, 2009 ... ISSN 1684–5315 © 2009 Academic Journals. Full Length ... performance of 36 young West African Dwarf (WAD) goats was investigated in order to simulate the .... cause antibody depression, alter white blood cell counts,.

  8. Sire influence on reproductive, performance characteristics and ...

    African Journals Online (AJOL)

    , Panda White x Cinnamon Brown (PWxCB) and Silver Brown x Cinnamon Brown (SBxCB). The experiment was a randomized complete block design. Parameters measured include: fertility and hatchability traits, growth performance traits and ...

  9. Emerging technologies for high performance infrared detectors

    OpenAIRE

    Tan Chee Leong; Mohseni Hooman

    2018-01-01

    Infrared photodetectors (IRPDs) have become important devices in various applications such as night vision, military missile tracking, medical imaging, industry defect imaging, environmental sensing, and exoplanet exploration. Mature semiconductor technologies such as mercury cadmium telluride and III–V material-based photodetectors have been dominating the industry. However, in the last few decades, significant funding and research has been focused to improve the performance of IRPDs such as...

  10. Data characteristics that determine classifier performance

    CSIR Research Space (South Africa)

    Van der Walt, Christiaan M

    2006-11-01

    Full Text Available available at [11]. The kNN uses a LinearNN nearest neighbour search algorithm with an Euclidean distance metric [8]. The optimal k value is determined by performing 10-fold cross-validation. An optimal k value between 1 and 10 is used for Experiments 1... classifiers. 10-fold cross-validation is used to evaluate and compare the performance of the classifiers on the different data sets. 3.1. Artificial data generation Multivariate Gaussian distributions are used to generate artificial data sets. We use d...

  11. performance characteristics of a cam turning attachment

    African Journals Online (AJOL)

    Dr Obe

    ABSTRACT. A modification of a cylindrical turning unit has been done to give a non- cylindrical turning attachment for production of irregular shapes, like cams on the lathe machine. To assess the performance of the attachment, cutting forces have been measured using a 'Sigma' Cutting Tool. Dynamometer. Furthermore ...

  12. Performance Engineering Technology for Scientific Component Software

    Energy Technology Data Exchange (ETDEWEB)

    Malony, Allen D.

    2007-05-08

    Large-scale, complex scientific applications are beginning to benefit from the use of component software design methodology and technology for software development. Integral to the success of component-based applications is the ability to achieve high-performing code solutions through the use of performance engineering tools for both intra-component and inter-component analysis and optimization. Our work on this project aimed to develop performance engineering technology for scientific component software in association with the DOE CCTTSS SciDAC project (active during the contract period) and the broader Common Component Architecture (CCA) community. Our specific implementation objectives were to extend the TAU performance system and Program Database Toolkit (PDT) to support performance instrumentation, measurement, and analysis of CCA components and frameworks, and to develop performance measurement and monitoring infrastructure that could be integrated in CCA applications. These objectives have been met in the completion of all project milestones and in the transfer of the technology into the continuing CCA activities as part of the DOE TASCS SciDAC2 effort. In addition to these achievements, over the past three years, we have been an active member of the CCA Forum, attending all meetings and serving in several working groups, such as the CCA Toolkit working group, the CQoS working group, and the Tutorial working group. We have contributed significantly to CCA tutorials since SC'04, hosted two CCA meetings, participated in the annual ACTS workshops, and were co-authors on the recent CCA journal paper [24]. There are four main areas where our project has delivered results: component performance instrumentation and measurement, component performance modeling and optimization, performance database and data mining, and online performance monitoring. This final report outlines the achievements in these areas for the entire project period. The submitted progress

  13. Performance characteristics of a shower cooling tower

    International Nuclear Information System (INIS)

    Qi Xiaoni; Liu Zhenyan; Li Dandan

    2007-01-01

    This study was prompted by the need to design towers for applications in which, due to salt deposition on the packing and subsequent blockage, the use of tower packing is not practical. In contrast to conventional cooling towers, the cooling tower analyzed in this study is void of fill. By means of efficient atomization nozzles, a shower cooling tower (SCT) is possible to be applied in industry, which, in terms of water cooling, energy saving and equipment investing, is better than conventional packed cooling towers. However, no systematic thermodynamic numerical method could be found in the literature up to now. Based on the kinetic model and mass and heat transfer model, this paper has developed a one dimensional model for studying the motional process and evaporative cooling process occurring at the water droplet level in the SCT. The finite difference approach is used for three motional processes to obtain relative parameters in each different stage, and the possibility of the droplets being entrained outside the tower is fully analyzed. The accuracy of this model is checked by practical operational results from a full scale prototype in real conditions, and some exclusive factors that affect the cooling characteristics for the SCT are analyzed in detail. This study provides the theoretical foundation for practical application of the SCT in industry

  14. Some useful characteristics of performance models

    International Nuclear Information System (INIS)

    Worledge, D.H.

    1985-01-01

    This paper examines the demands placed upon models of human cognitive decision processes in application to Probabilistic Risk Assessment. Successful models, for this purpose, should, 1) be based on proven or plausible psychological knowledge, e.g., Rasmussen's mental schematic, 2) incorporate opportunities for slips, 3) take account of the recursive nature, in time, of corrections to mistaken actions, and 4) depend on the crew's predominant mental states that accompany such recursions. The latter is equivalent to an explicit coupling between input and output of Rasmussen's mental schematic. A family of such models is proposed with observable rate processes mediating the (conscious) mental states involved. It is expected that the cumulative probability distributions corresponding to the individual rate processes can be identified with probability-time correlations of the HCR Human Cognitive Reliability type discussed elsewhere in this session. The functional forms of the conditional rates are intuitively shown to have simple characteristics that lead to a strongly recursive stochastic process with significant predictive capability. Models of the type proposed have few parts and form a representation that is intentionally far short of a fully transparent exposition of the mental process in order to avoid making impossible demands on data

  15. Performance and carcass characteristics of Yankasa ram fed with ...

    African Journals Online (AJOL)

    Remember me ... and 50% maize and wheat offal mixture, were better when compared to the control (B0) and other test diet in terms of performance and carcass characteristics. ... Key words: Performance, carcass, biscuit waste, Yankasa ram.

  16. Performance characteristics for advanced control systems

    International Nuclear Information System (INIS)

    Kisner, R.A.

    1989-01-01

    A growing collection of control techniques is becoming available to the design engineer. This make selection of the most appropriate technique for a given application a difficult task. A systematic approach to evaluating alternative control schemes is needed. The approach discussed in this paper expands the traditional concepts of quantitative performance analysis to include other relevant factors such as robustness of the technique, resource requirements, and effects on operators and other personnel. This collection of factors, termed measures of utility, may be used as qualitative and quantitative means of evaluating and comparing properties of alternative control system designs. This paper, although not an in-depth study, serves to outline several measures of utility and suggests a general structure for control system development. This method of comparing the usefulness of alternative control system will prove valuable to the ORNL Advanced Controls Program (ACTO) for optimizing compatibility with actual systems and equipment

  17. Silicon on insulator technology. Characteristics. Applications; Technologies silicium sur isolant. Caracteristiques. Exemples d'application

    Energy Technology Data Exchange (ETDEWEB)

    Suat, J. P.; Peccoud, L.; Le Goascoz, V.; Garcia, M.; Mackowiak, E.

    1975-01-31

    The advantages resulting from a SOS (Silicon-on-Sapphire) MOS technology are demonstrated. Experimental results giving the performance of C.MOS and depletion-enrichment P-channel technologies are presented, with an application of Silicon on insulator on development, that is to say a 1024 bits MNOS memory, peripheral circuits being developed according to the depletion-enrichment technology.

  18. PRODUCTION WELL PERFORMANCE ENHANCEMENT USING SONICATION TECHNOLOGY

    Energy Technology Data Exchange (ETDEWEB)

    Michael A. Adewumi; M. Thaddeus Ityokumbul; Robert W. Watson; Mario Farias; Glenn Heckman; Johnson Olanrewaju; Eltohami Eltohami; Bruce G. Miller; W. Jack Hughes; Thomas C. Montgomery

    2003-12-17

    The objective of this project is to develop a sonic well performance enhancement technology that focuses on near wellbore formations. In order to successfully achieve this objective, a three-year project has been defined with each year consisting of four tasks. The first task is the laboratory-scale study whose goal is to determine the underlying principles of the technology. The second task will develop a scale-up mathematical model to serve as the design guide for tool development. The third task is to develop effective transducers that can operate with variable frequency so that the most effective frequencies can be applied in any given situation. The system, assembled as part of the production string, ensures delivery of sufficient sonic energy to penetrate the near-wellbore formation. The last task is the actual field testing of the tool. The first year of the project has been completed.

  19. MODEL OF EMERGENCY DEPARTMENT NURSE PERFORMANCE IMPROVEMENT BASED ON ASSOCIATION OF INDIVIDUAL CHARACTERISTIC, ORGANIZATION CHARACTERISTIC AND JOB CHARACTERISTIC

    Directory of Open Access Journals (Sweden)

    Maria Margaretha Bogar

    2017-04-01

    Full Text Available Introduction: Nursing care is integral part of health care and having important role in management of patient with emergency condition. The purpose of this research was to develop nurse performance improvement model based on individual, organization and job characteristics association in Emergency Department of RSUD dr TC Hillers Maumere. Method: This was an explanative survey by cross sectional approach held on July -August 2012. Respondents in this study were 22 nurses and 44 patients were obtained by purposive sampling technique. Data were analyzed by partial least square test and signi fi cant t value > 1.64 (alpha 10%. Result: Results showed that individual characteristic had effect on nurse performance (t = 7.59, organization characteristic had effect on nurse performance (t = 2.03 and job characteristic didn’t have effect on nurse performance (t = 0.88. Nurse performance had effect on patient satisfaction (t = 6.54 but nurse satisfaction didn’t have effect on nurse performance (t = 1.31, and nurse satisfaction didn’t have effect either on patient satisfaction (t = 0.94. Discussion: This research concluded that individual characteristics which in fl uence nurse performance in nursing care were ability and skill, experience, age, sex, attitude and motivation. Organization characteristic that influence nurse performance was reward while job characteristic that include job design and feedback didn’t influence nurse performance in nursing care. Nurse performance influenced patient satisfaction but nurse satisfaction didn’t influence patient satisfaction and nurse performance.

  20. Performance evaluation soil samples utilizing encapsulation technology

    Science.gov (United States)

    Dahlgran, James R.

    1999-01-01

    Performance evaluation soil samples and method of their preparation using encapsulation technology to encapsulate analytes which are introduced into a soil matrix for analysis and evaluation by analytical laboratories. Target analytes are mixed in an appropriate solvent at predetermined concentrations. The mixture is emulsified in a solution of polymeric film forming material. The emulsified solution is polymerized to form microcapsules. The microcapsules are recovered, quantitated and introduced into a soil matrix in a predetermined ratio to form soil samples with the desired analyte concentration.

  1. Research about reactor operator's personality characteristics and performance

    International Nuclear Information System (INIS)

    Wei Li; He Xuhong; Zhao Bingquan

    2003-01-01

    To predict and evaluate the reactor operator's performance by personality characteristics is an important part of reactor operator safety assessment. Using related psychological theory combined with the Chinese operator's fact and considering the effect of environmental factors to personality analysis, paper does the research about the about the relationships between reactor operator's performance and personality characteristics, and offers the reference for operator's selection, using and performance in the future. (author)

  2. Job Characteristics, Work Involvement, and Job Performance of Public Servants

    Science.gov (United States)

    Johari, Johanim; Yahya, Khulida Kirana

    2016-01-01

    Purpose: The primary purpose of this study is to assess the predicting role of job characteristics on job performance. Dimensions in the job characteristics construct are skill variety, task identity, task significance, autonomy and feedback. Further, work involvement is tested as a mediator in the hypothesized link. Design/methodology/approach: A…

  3. Analysis of characteristic performance curves in radiodiagnosis by an observer

    International Nuclear Information System (INIS)

    Kossovoj, A.L.

    1988-01-01

    Methods and ways of construction of performance characteristic curves (PX-curves) in roentgenology, their qualitative and quantitative estimation are described. Estimation of PX curves application for analysis of scintigraphic and sonographic images is presented

  4. Evaluation of the productive performance characteristics of red ...

    African Journals Online (AJOL)

    Evaluation of the productive performance characteristics of red tilapia ( Oreochromis sp.) injected with shark DNA into skeletal muscles and maintained diets containing different levels of probiotic and amino yeast.

  5. The Influence of Top Management Team Characteristics on BPD Performance

    Directory of Open Access Journals (Sweden)

    Joy Elly Tulung

    2015-12-01

    Full Text Available Based on ”upper echelons theory”, this paper investigates the relation between top management team composition and BPD performance. For top management team characteristics, we employ age, level of education, background of education, gender, and functional background, while for measured the BPD performance we employ return on asset (ROA, return on equity (ROE, capital adequacy ratio (CAR, net interest margin (NIM, loan to deposit ratio (LDR, non-performing loan (NPL and operation expenses to operation income (BOPO. The results show that all characteristics have positive significant influences on BPD performance.

  6. Regional characteristics relevant to advanced technology cogeneration development. [industrial energy

    Science.gov (United States)

    Manvi, R.

    1981-01-01

    To assist DOE in establishing research and development funding priorities in the area of advanced energy conversion technoloy, researchers at the Jet Propulsion Laboratory studied those specific factors within various regions of the country that may influence cogeneration with advanced energy conversion systems. Regional characteristics of advanced technology cogeneration possibilities are discussed, with primary emphasis given to coal derived fuels. Factors considered for the study were regional industry concentration, purchased fuel and electricity prices, environmental constraints, and other data of interest to industrial cogeneration.

  7. Technology diversification, coherence, and performance of firms

    NARCIS (Netherlands)

    Leten, B.; Belderbos, R.A.; Looy, van B.

    2007-01-01

    Technological diversification at the firm level (i.e., the expansion of a firm's technology base into a wide range of technology fields) is found to be a prevailing phenomenon in all three major industrialized regions,—the United States, Europe, and Japan—prompting the term multitechnology

  8. Hospital ownership, decisions on supervisory board characteristics, and financial performance.

    Science.gov (United States)

    Kuntz, Ludwig; Pulm, Jannis; Wittland, Michael

    2016-01-01

    Dynamic and complex transformations in the hospital market increase the relevance of good corporate governance. However, hospital performance and the characteristics of supervisory boards differ depending on ownership. The question therefore arises whether hospital owners can influence performance by addressing supervisory board characteristics. The objective of this study is to explain differences in the financial performance of hospitals with regard to ownership by studying the size and composition of supervisory boards. The AMADEUS database was used to collect information on hospital financial performance in 2009 and 2010. Business and quality reports, hospital websites, and data from health insurer were used to obtain information on hospital and board characteristics. The resulting sample consisted of 175 German hospital corporations. We utilized ANOVA and regression analysis to test a mediation hypothesis that investigated whether decisions regarding board size and composition were associated with financial performance and could explain performance differences. Financial performance and board size and composition depend on ownership. An increase in board size and greater politician participation were negatively associated with all five tested measures of financial performance. Furthermore, an increase in physician participation was positively associated with one dimension of financial performance, whereas one negative relationship was identified for nurse and economist participation. For clerics, no associations were found. Decisions concerning board size and composition are important as they relate to hospital financial performance. We contribute to existing research by showing that, in addition to board size and physician participation, the participation of other professionals can also influence financial performance.

  9. Aggregate packing characteristics of good and poor performing asphalt mixes

    CSIR Research Space (South Africa)

    Denneman, E

    2007-07-01

    Full Text Available The aggregate structure of the compacted mix is a determining factor for the performance of Hot-Mix Asphalt (HMA). In this paper, the grading characteristics of good and poor performing HMA mixes are explored using the concepts of the Bailey method...

  10. Relationship Between Job Characteristics And Job Performance Of ...

    African Journals Online (AJOL)

    The agricultural extension agent is a key stakeholder in extension systems. The nature of their work is so important that it has overriding effect on their job performance. This study investigates the relationship between job characteristics and job performance of agricultural extension agents in Imo and Rivers States, Nigeria.

  11. Influence of course characteristics, student characteristics, and behavior in learning management systems on student performance

    OpenAIRE

    Conijn, Rianne; Kleingeld, Ad; Matzat, Uwe; Snijders, Chris; van Zaanen, Menno

    2016-01-01

    The use of learning management systems (LMS) in education make it possible to track students’ online behavior. This data can be used for educational data mining and learning analytics, for example, by predicting student performance. Although LMS data might contain useful predictors, course characteristics and student characteristics have shown to influence student performance as well. However, these different sets of features are rarely combined or compared. Therefore, in the current study we...

  12. Nonlinear Performance Characteristics of Flux-Switching PM Motors

    Directory of Open Access Journals (Sweden)

    E. Ilhan

    2013-01-01

    Full Text Available Nonlinear performance characteristics of 3-phase flux-switching permanent magnet motors (FSPM are overviewed. These machines show advantages of a robust rotor structure and a high energy density. Research on the FSPM is predominated by topics such as modeling and machine comparison, with little emphasis given on its performance and limits. Performance characteristics include phase flux linkage, phase torque, and phase inductance. In the paper, this analysis is done by a cross-correlation of rotor position and armature current. Due to the high amount of processed data, which cannot be handled analytically within an acceptable time period, a multistatic 2D finite element model (FEM is used. For generalization, the most commonly discussed FSPM topology, 12/10 FSPM, is chosen. Limitations on the motor performance due to the saturation are discussed on each characteristic. Additionally, a focused overview is given on energy conversion loops and dq-axes identification for the FSPM.

  13. Covariance of engineering management characteristics with engineering employee performance

    Science.gov (United States)

    Hesketh, Andrew Arthur

    1998-12-01

    As business in the 1990's grapples with the impact of continuous improvement and quality to meet market demands, there is an increased need to improve the leadership capabilities of our managers. Engineers have indicated desire for certain managerial characteristics in their leadership but there have been no studies completed that approached the problem of determining what managerial characteristics were best at improving employee performance. This study addressed the idea of identifying certain managerial characteristics that enhance employee performance. In the early 1990's, McDonnell Douglas Aerospace in St. Louis used a forced distribution system and allocated 35% of its employees into a "exceeds expectations" category and 60% into a "meets expectations" category. A twenty-question 5 point Likert scale survey on managerial capabilities was administered to a sample engineering population that also obtained their "expectations" category. A single factor ANOVA on the survey results determined a statistical difference between the "exceeds" and "meets" employees with four of the managerial capability questions. The "exceeds expectations" employee indicated that supervision did a better job of supporting subordinate development, clearly communicating performance expectations, and providing timely performance feedback when compared to the "meets expectations" employee. The "meets expectations" employee felt that their opinions, when different from their supervisor's, were more often ignored when compared to the "exceeds expectations" employee. These four questions relate to two specific managerial characteristics, "gaining (informal) authority and support" or "control" characteristic and "providing assistance and guidance" or "command" characteristic, that can be emphasized in managerial training programs.

  14. Comparative Characteristics of Technology Transfer in Developed Countries

    Directory of Open Access Journals (Sweden)

    Natalia Palii

    2013-08-01

    Full Text Available The research into innovation transfer in the global economy is a very urgent issue under the modern conditions of development of any country. Comparative characteristics of technology transfer in such countries and regions as the USA, EU, Asia, presented in the article, permit us to detect certain patterns of this process inherent both in developed and developing countries. The analysis made in the article can be useful for developing technology transfer processes in the Danube countries’ economy. The analytical method used in this research allowed us to determine the factor that is crucial for the growth of the world market of high-technology products and services. The analysis was conducted on several criteria such as the level of expenditure on R&D in the whole global economy, as well as in individual countries and regions. Besides, there were taken into account the added value of high-tech industries and the share of expenditure on R&D in total production costs. The conclusions regarding the effectiveness of funds allocated for scientific research and experimental development in the U.S. can be drawn on the basis of data presented in the paper on the amount of added value of the U.S. high-tech industries.

  15. Examining hemodialyzer membrane performance using proteomic technologies.

    Science.gov (United States)

    Bonomini, Mario; Pieroni, Luisa; Di Liberato, Lorenzo; Sirolli, Vittorio; Urbani, Andrea

    2018-01-01

    The success and the quality of hemodialysis therapy are mainly related to both clearance and biocompatibility properties of the artificial membrane packed in the hemodialyzer. Performance of a membrane is strongly influenced by its interaction with the plasma protein repertoire during the extracorporeal procedure. Recognition that a number of medium-high molecular weight solutes, including proteins and protein-bound molecules, are potentially toxic has prompted the development of more permeable membranes. Such membrane engineering, however, may cause loss of vital proteins, with membrane removal being nonspecific. In addition, plasma proteins can be adsorbed onto the membrane surface upon blood contact during dialysis. Adsorption can contribute to the removal of toxic compounds and governs the biocompatibility of a membrane, since surface-adsorbed proteins may trigger a variety of biologic blood pathways with pathophysiologic consequences. Over the last years, use of proteomic approaches has allowed polypeptide spectrum involved in the process of hemodialysis, a key issue previously hampered by lack of suitable technology, to be assessed in an unbiased manner and in its full complexity. Proteomics has been successfully applied to identify and quantify proteins in complex mixtures such as dialysis outflow fluid and fluid desorbed from dialysis membrane containing adsorbed proteins. The identified proteins can also be characterized by their involvement in metabolic and signaling pathways, molecular networks, and biologic processes through application of bioinformatics tools. Proteomics may thus provide an actual functional definition as to the effect of a membrane material on plasma proteins during hemodialysis. Here, we review the results of proteomic studies on the performance of hemodialysis membranes, as evaluated in terms of solute removal efficiency and blood-membrane interactions. The evidence collected indicates that the information provided by proteomic

  16. Emerging technologies for high performance infrared detectors

    Science.gov (United States)

    Tan, Chee Leong; Mohseni, Hooman

    2018-01-01

    Infrared photodetectors (IRPDs) have become important devices in various applications such as night vision, military missile tracking, medical imaging, industry defect imaging, environmental sensing, and exoplanet exploration. Mature semiconductor technologies such as mercury cadmium telluride and III-V material-based photodetectors have been dominating the industry. However, in the last few decades, significant funding and research has been focused to improve the performance of IRPDs such as lowering the fabrication cost, simplifying the fabrication processes, increasing the production yield, and increasing the operating temperature by making use of advances in nanofabrication and nanotechnology. We will first review the nanomaterial with suitable electronic and mechanical properties, such as two-dimensional material, graphene, transition metal dichalcogenides, and metal oxides. We compare these with more traditional low-dimensional material such as quantum well, quantum dot, quantum dot in well, semiconductor superlattice, nanowires, nanotube, and colloid quantum dot. We will also review the nanostructures used for enhanced light-matter interaction to boost the IRPD sensitivity. These include nanostructured antireflection coatings, optical antennas, plasmonic, and metamaterials.

  17. Emerging technologies for high performance infrared detectors

    Directory of Open Access Journals (Sweden)

    Tan Chee Leong

    2018-01-01

    Full Text Available Infrared photodetectors (IRPDs have become important devices in various applications such as night vision, military missile tracking, medical imaging, industry defect imaging, environmental sensing, and exoplanet exploration. Mature semiconductor technologies such as mercury cadmium telluride and III–V material-based photodetectors have been dominating the industry. However, in the last few decades, significant funding and research has been focused to improve the performance of IRPDs such as lowering the fabrication cost, simplifying the fabrication processes, increasing the production yield, and increasing the operating temperature by making use of advances in nanofabrication and nanotechnology. We will first review the nanomaterial with suitable electronic and mechanical properties, such as two-dimensional material, graphene, transition metal dichalcogenides, and metal oxides. We compare these with more traditional low-dimensional material such as quantum well, quantum dot, quantum dot in well, semiconductor superlattice, nanowires, nanotube, and colloid quantum dot. We will also review the nanostructures used for enhanced light-matter interaction to boost the IRPD sensitivity. These include nanostructured antireflection coatings, optical antennas, plasmonic, and metamaterials.

  18. Production Well Performance Enhancement using Sonication Technology

    Energy Technology Data Exchange (ETDEWEB)

    Adewumi, Michael A; Ityokumbul, M Thaddeus; Watson, Robert W; Eltohami, Eltohami; Farias, Mario; Heckman, Glenn; Houlihan, Brendan; Karoor, Samata Prakash; Miller, Bruce G; Mohammed, Nazia; Olanrewaju, Johnson; Ozdemir, Mine; Rejepov, Dautmamed; Sadegh, Abdallah A; Quammie, Kevin E; Zaghloul, Jose; Hughes, W Jack; Montgomery, Thomas C

    2005-12-31

    The objective of this project was to develop a sonic well performance enhancement technology that focused on near wellbore formation damage. In order to successfully achieve this objective, a three-year project was defined. The entire project was broken into four tasks. The overall objective of all this was to foster a better understanding of the mechanisms involved in sonic energy interactions with fluid flow in porous media and adapt such knowledge for field applications. The fours tasks are: • Laboratory studies • Mathematical modeling • Sonic tool design and development • Field demonstration The project was designed to be completed in three years; however, due to budget cuts, support was only provided for the first year, and hence the full objective of the project could not be accomplished. This report summarizes what was accomplished with the support provided by the US Department of Energy. Experiments performed focused on determining the inception of cavitation, studying thermal dissipation under cavitation conditions, investigating sonic energy interactions with glass beads and oil, and studying the effects of sonication on crude oil properties. Our findings show that the voltage threshold for onset of cavitation is independent of transducer-hydrophone separation distance. In addition, thermal dissipation under cavitation conditions contributed to the mobilization of deposited paraffins and waxes. Our preliminary laboratory experiments suggest that waxes are mobilized when the fluid temperature approaches 40°C. Experiments were conducted that provided insights into the interactions between sonic wave and the fluid contained in the porous media. Most of these studies were carried out in a slim-tube apparatus. A numerical model was developed for simulating the effect of sonication in the nearwellbore region. The numerical model developed was validated using a number of standard testbed problems. However, actual application of the model for scale

  19. Information and communication technology and bank performance ...

    African Journals Online (AJOL)

    Different sectors of world economies are rapidly being affected by improved technology. Banking sector is also witnessing the trend in Nigeria. Information and communication Technology is said to have impacted the banking sector massively as the banks in Nigeria introduce products that would help improve their efficiency ...

  20. Research of psychological characteristics and performance relativity of operators

    International Nuclear Information System (INIS)

    Fang Xiang; He Xuhong; Zhao Bingquan

    2008-01-01

    Based on the working tasks of an operator being taken into full consideration in this paper, on the one hand the table of measuring psychological characteristics is designed through the selection of special dimensions; on the other hand the table of performance appraisal is drafted through the choice of suitable standards of an operator. The paper analyzes the results of two aspects, sets relevant nuclear power plant operators as the research objective, and obtains the psychological characteristics and performance relativity of operators. The research can be as important and applied reference for the selection, evaluation and use of operators

  1. Examining hemodialyzer membrane performance using proteomic technologies

    Directory of Open Access Journals (Sweden)

    Bonomini M

    2017-12-01

    Full Text Available Mario Bonomini,1 Luisa Pieroni,2 Lorenzo Di Liberato,1 Vittorio Sirolli,1 Andrea Urbani2,3 1Department of Medicine, G. d’Annunzio University, Chieti, 2Proteomic and Metabonomic Units, IRCCS S. Lucia Foundation, Rome, 3Faculty of Medicine, Biochemistry and Clinical Biochemistry Institute, Catholic University of the “Sacred Heart”, Rome, Italy Abstract: The success and the quality of hemodialysis therapy are mainly related to both clearance and biocompatibility properties of the artificial membrane packed in the hemodialyzer. Performance of a membrane is strongly influenced by its interaction with the plasma protein repertoire during the extracorporeal procedure. Recognition that a number of medium–high molecular weight solutes, including proteins and protein-bound molecules, are potentially toxic has prompted the development of more permeable membranes. Such membrane engineering, however, may cause loss of vital proteins, with membrane removal being nonspecific. In addition, plasma proteins can be adsorbed onto the membrane surface upon blood contact during dialysis. Adsorption can contribute to the removal of toxic compounds and governs the biocompatibility of a membrane, since surface-adsorbed proteins may trigger a variety of biologic blood pathways with pathophysiologic consequences. Over the last years, use of proteomic approaches has allowed polypeptide spectrum involved in the process of hemodialysis, a key issue previously hampered by lack of suitable technology, to be assessed in an unbiased manner and in its full complexity. Proteomics has been successfully applied to identify and quantify proteins in complex mixtures such as dialysis outflow fluid and fluid desorbed from dialysis membrane containing adsorbed proteins. The identified proteins can also be characterized by their involvement in metabolic and signaling pathways, molecular networks, and biologic processes through application of bioinformatics tools. Proteomics may

  2. Facebook use, personality characteristics and academic performance: A correlational study

    OpenAIRE

    Sapsani, Georgia; Tselios, Nikolaos

    2017-01-01

    The present paper examines the relationship between the students personality, use of social media and their academic performance and engagement. In specific, the aim of this study is to examine the relationship of students facebook (fb) use and personality characteristics using the Big Five Personality Test with (a) student engagement, (b) time spent preparing for class, (c) time spent in co-curricular activities and (d) academic performance. Results illustrate that fb time was significantly ...

  3. Performance characteristics of the Mayo/IBM PACS

    Science.gov (United States)

    Persons, Kenneth R.; Gehring, Dale G.; Pavicic, Mark J.; Ding, Yingjai

    1991-07-01

    The Mayo Clinic and IBM (at Rochester, Minnesota) have jointly developed a picture archiving system for use with Mayo's MRI and Neuro CT imaging modalities. The communications backbone of the PACS is a portion of the Mayo institutional network: a series of 4-Mbps token rings interconnected by bridges and fiber optic extensions. The performance characteristics of this system are important to understand because they affect the response time a PACS user can expect, and the response time for non-PACS users competing for resources on the institutional network. The performance characteristics of each component and the average load levels of the network were measured for various load distributions. These data were used to quantify the response characteristics of the existing system and to tune a model developed by North Dakota State University Department of Computer Science for predicting response times of more complex topologies.

  4. Desulfurization technologies for flue gases from power stations, technological and financial characteristics

    International Nuclear Information System (INIS)

    Naumoski, Koce

    1997-01-01

    Harms on life environment, caused by aero pollution, for the last decades enforced fast development of technologies for filtration of gases that come from thermal power plants and other objects. SO 2 , that appear as one of outputs of fossil fuels combustion, and also processing of sulphide ore, is a main component of acid rains. Acid rains represent one of the most risky factors, responsible for dryne of woods and changing of flora and fauna on land and in water. Starting from 1931 year when on the thermal power plant BATTERSEA STATION, property of London Power, first scrubbers were monnted for filtration of flue gases of SO 2 , and up till today, many procedures are developed for desulfurization of flue gases. For easier coping with numerous technologies for desulfurization , various classifications were made. By state of aggregation of the absorption agent , the technologies for desulfurization of gases are divided in wet , semidry and dry procedures. Wet procedures are technologies with highness rate of desulfurization of 90-95 % and most flexible of the quality of fuel whose flue gases are filtered. Presently they have high price of 90-220 $/kw installed power. According to American sources, their price at the world market is forecasted that till 2000 year will reach price of 100 $/kw. Dry technologies for desulfurization of flue gases are last technologies. The rate of desulfurization is 50-60 % and its prise is 76 -113 $/kw. Their negative side is high variable costs 250 - 388 $/ ton SO 2 (at wet procedures variable costs 76 - 157 $/ton SO 2 ). Semidry technologies by financial and technological characteristics are wet and dry procedures. (Author)

  5. Performance Characteristics of an Armature Voltage Controlled D.C. ...

    African Journals Online (AJOL)

    In this paper, the performance study of a separately excited d. c. motor whose speed is controlled by armature voltage variation is presented. Both the open loop and the closed loop steady state and transient characteristics are reported. The speed controllers considered in the closed loop mode are the proportional and the ...

  6. Performance and Carcass Characteristics of Broiler Finisher Birds ...

    African Journals Online (AJOL)

    Sixty (60) 4 weeks old Anak broiler strain were subjected to 28 days feeding trial at the Poultry Unit of the Teaching and Research Farm, Evan Enwerem, Owerri, Nigeria, to determine the dietary effect of pineapple wine sediment (PWSM) on their performance and carcass characteristics. The birds were divided into four ...

  7. Do the Managerial Characteristics of Schools Influence Their Performance?

    Science.gov (United States)

    Agasisti, Tommaso; Bonomi, Francesca; Sibiano, Piergiacomo

    2012-01-01

    Purpose: The purpose of this paper is to investigate the role of governance and managerial characteristics of schools. More specifically, the aim is to individuate the factors that are associated to higher schools' performances, as measured through student achievement. Design/methodology/approach: The research is conducted by means of a survey in…

  8. Performance characteristics of proximity focused ultraviolet image converters

    Science.gov (United States)

    Williams, J. T.; Feibelman, W. A.

    1973-01-01

    Performance characteristics of Bendix type BX 8025-4522 proximity focused image tubes for UV to visible light conversion are presented. Quantum efficiency, resolution, background, geometric distortion, and environmental test results are discussed. The converters use magnesium fluoride input windows with Cs-Te photocathodes and P-11 phosphors on fiber optic output windows.

  9. Growth performance, carcass and organ characteristics of growing ...

    African Journals Online (AJOL)

    An experiment was conducted at the Department of Animal Science teaching and research farm, Bayero University Kano, to evaluate the effect of feeding graded levels of Moringa oleifera leaf meal (MOLM) in diets on growth performance, carcass and organ characteristics of weaned rabbits. Twenty eight grower rabbits of ...

  10. Performance and ileal characteristics of finishing broilers fed diets ...

    African Journals Online (AJOL)

    An experiment was conducted to evaluate the effect of prebiotics supplemented diets on performance characteristics and gut morphology of broiler chickens. The study involved 320 day-old Anak broiler chicks, used to assess the utilization of prebiotics [Mannose oligosaccharides (MOS) and Lactose oligosaccharides ...

  11. Nonlinear performance characteristics of flux-switching PM motors

    NARCIS (Netherlands)

    Ilhan, E.; Kremers, M.F.J.; Motoasca, T.E.; Paulides, J.J.H.; Lomonova, E.

    2013-01-01

    Nonlinear performance characteristics of 3-phase flux-switching permanent magnet motors (FSPM) are overviewed. These machines show advantages of a robust rotor structure and a high energy density. Research on the FSPM is predominated by topics such as modeling and machine comparison, with little

  12. Performance characteristics of broiler chicks fed kidney bean as ...

    African Journals Online (AJOL)

    An experiment was conducted to investigate the effect of replacing soybean meal and groundnut cake meal with cooked and decorticated kidney bean seed meals on the performance characteristics of broilers. One hundred and eighty day old broiler chicks of Anak strain were raised on six experimental diets.

  13. Characteristic test technology for PWR fuel and its components

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dae Ho; Lee, Chan Bock; Bang, Je Gun; Jung, Yeon Ho; Jeong, Yong Hwan; Park, Sang Yoon; Kim, Kyeng Ho; Nam, Cheol; Baek, Jong Hyuk; Lee, Myung Ho; Choi, Byoung Kwon; Song, Kun Woo; Kang, Ki Won; Kim, Keon Sik; Kim, Jong Hun; Kim, Young Min; Yang, Jae Ho; Song, Kee Nam; Kim, Hyung Kyu; Kang, Heung Seok; Yoon, Kyung Ho; Chun, Tae Hyun; In, Wang Kee; Oh, Dong Seok [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-01-01

    Characteristic tests of fuel assembly and its components being developed in the Advanced LWR Fuel Development Project supported by the mid-long term nuclear R and D program are described in this report. Performance verification of fuel and its components by the characteristic tests are essential to their development. Fuel components being developed in the Advanced LWR Fuel Development Project are zirconium alloy cladding, UO{sub 2} and burnable absorber pellets, spacer grid and top and bottom end pieces. Detailed test plans for those fuel components are described in this report, and test procedures of cladding and pellet are also described in the Appendix. Examples of the described tests are in- and out-of- pile corrosion and mechanical tests such as creep and burst tests for the cladding, in-pile capsule and ramp tests for the pellet, mechanical tests such as strength and vibration, and thermal-hydraulic tests such as pressure drop and critical heat flux for the spacer grid and top and bottom end pieces. It is expected that this report could be used as the standard reference for the performance verification tests in the development of LWR fuel and its components. 11 refs., 9 figs., 2 tabs. (Author)

  14. Relations between mental health team characteristics and work role performance.

    Science.gov (United States)

    Fleury, Marie-Josée; Grenier, Guy; Bamvita, Jean-Marie; Farand, Lambert

    2017-01-01

    Effective mental health care requires a high performing, interprofessional team. Among 79 mental health teams in Quebec (Canada), this exploratory study aims to 1) determine the association between work role performance and a wide range of variables related to team effectiveness according to the literature, and to 2) using structural equation modelling, assess the covariance between each of these variables as well as the correlation with other exogenous variables. Work role performance was measured with an adapted version of a work role questionnaire. Various independent variables including team manager characteristics, user characteristics, team profiles, clinical activities, organizational culture, network integration strategies and frequency/satisfaction of interactions with other teams or services were analyzed under the structural equation model. The later provided a good fit with the data. Frequent use of standardized procedures and evaluation tools (e.g. screening and assessment tools for mental health disorders) and team manager seniority exerted the most direct effect on work role performance. While network integration strategies had little effect on work role performance, there was a high covariance between this variable and those directly affecting work role performance among mental health teams. The results suggest that the mental healthcare system should apply standardized procedures and evaluation tools and, to a lesser extent, clinical approaches to improve work role performance in mental health teams. Overall, a more systematic implementation of network integration strategies may contribute to improved work role performance in mental health care.

  15. Job characteristics, flow, and performance: the moderating role of conscientiousness.

    Science.gov (United States)

    Demerouti, Evangelia

    2006-07-01

    The present article aims to show the importance of positive work-related experiences within occupational health psychology by examining the relationship between flow at work (i.e., absorption, work enjoyment, and intrinsic work motivation) and job performance. On the basis of the literature, it was hypothesized that (a) motivating job characteristics are positively related to flow at work and (b) conscientiousness moderates the relationship between flow and other ratings of (in-role and out-of-role) performance. The hypotheses were tested on a sample of 113 employees from several occupations. Results of moderated structural equation modeling analyses generally supported the hypotheses. Motivating job characteristics were predictive of flow, and flow predicted in-role and extra-role performance, for only conscientious employees.

  16. Parametric study of geohydrologic performance characteristics for geologic waste repositories

    International Nuclear Information System (INIS)

    Bailey, C.E.; Marine, I.W.

    1980-11-01

    One of the major objectives of the National Waste Terminal Storage Program is to identify potential geologic sites for storage and isolation of radioactive waste (and possibly irradiated fuel). Potential sites for the storage and isolation of radioactive waste or spent fuel in a geologic rock unit are being carefully evaluated to ensure that radionuclides from the stored waste or fuel will never appear in the biosphere in amounts that would constitute a hazard to the health and safety of the public. The objective of this report is to quantify and present in graphical form the effects of significant geohydrologic and other performance characteristics that would influence the movement of radionuclides from a storage site in a rock unit to the biosphere. The effort in this study was focused on transport by groundwater because that is the most likely method of radionuclide escape. Graphs of the major performance characteristics that influence the transport of radionuclides from a repository to the biosphere by groundwater are presented. The major characteristics addressed are radioactive decay, leach rate, hydraulic conductivity, porosity, groundwater gradient, hydrodynamic dispersion, ion exchange, and distance to the biosphere. These major performance characteristics are combind with each other and with the results of certain other combinations and presented in graphical form to provide the interrelationships of values measured during field studies. The graphical form of presentation should be useful in the screening process of site selection. An appendix illustrates the use of these graphs to assess the suitability of a site

  17. General performance characteristics of an irreversible ferromagnetic Stirling refrigeration cycle

    International Nuclear Information System (INIS)

    Lin, G.; Tegus, O.; Zhang, L.; Brueck, E.

    2004-01-01

    A new magnetic-refrigeration-cycle model using ferromagnetic materials as a cyclic working substance is set up, in which finite-rate heat transfer, heat leak and regeneration time are taken into account. On the basis of the thermodynamic properties of a ferromagnetic material, the general performance characteristics of the ferromagnetic Stirling refrigeration cycle are investigated and the effects of some key irreversibilities on the performance of the cycle are revealed. By using the optimal-control theory, the optimal relation between the coefficient of performance and the cooling rate is derived and some important performance bounds, e.g., the maximum cooling rate, the maximum coefficient of performance, are determined. Moreover, the optimal operating regions for cooling rate, coefficient of performance and the optimal operating temperatures of a cyclic working substance in the two heat-transfer processes are obtained. Furthermore, the influences of magnetization and magnetic field on the performance characteristics of the cycle are discussed. The results obtained here have general significance and can be deduced to the related ones of the Stirling refrigeration cycle using paramagnetic salt as a cyclic working substance

  18. Empirical Relationships among Technological Characteristics, Global Orientation, and Internationalisation of South Korean New Ventures

    Directory of Open Access Journals (Sweden)

    Junghyun Yoon

    2016-12-01

    Full Text Available International new ventures (INVs that pursue rapid internationalisation have received a growing amount of attention worldwide. This study, therefore, examined characteristics of INVs, and hence investigated empirically the relationships among the technological characteristics of INVs, the characteristics of their chief executive officers (CEOs (i.e., global orientation, and their internationalisation such as the level of internationalisation. The findings of this study can be summarised as follows: all of the technological characteristics (e.g., technological capacity, imitation, innovation, and standardisation have significant effects on the internationalisation of INVs. Furthermore, the CEO’s global orientation mediated the relationship between the technological characteristics and internationalisation.

  19. Performance characteristics of mix oil biodiesel blends with smoke emissions

    Directory of Open Access Journals (Sweden)

    Sanjay Mohite

    2016-08-01

    July 10th 2016; Available online How to Cite This Article: Mohite. S, Kumar, S. &  Maji, S.  (2016 Performance  characteristics of mix oil biodiesel blends with smoke emissions. Int. Journal of Renewable Energy Development, 5(2, 163-170. http://dx.doi.org/10.14710/ijred.5.2.163-170 

  20. Dry process fuel performance technology development

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Kweon Ho; Kim, K. W.; Kim, B. K. (and others)

    2006-06-15

    The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

  1. Dry process fuel performance technology development

    International Nuclear Information System (INIS)

    Kang, Kweon Ho; Kim, K. W.; Kim, B. K.

    2006-06-01

    The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

  2. Gamma radiation influence on technological characteristics of wheat flour

    Science.gov (United States)

    Teixeira, Christian A. H. M.; Inamura, Patricia Y.; Uehara, Vanessa B.; Mastro, Nelida L. d.

    2012-08-01

    This study aimed at determining the influence of gamma radiation on technological characteristics of wheat (Triticum sativum) flour and physical properties of pan breads made with this flour. The bread formulation included wheat flour, water, milk, salt, sugar, yeast and butter. The α-amylase activity of wheat flour irradiated with 1, 3 and 9 kGy in a Gammacell 220 (AECL), one day, five days and one month after irradiation was evaluated. Deformation force, height and weight of breads prepared with the irradiated flour were also determined. The enzymatic activity increased—reduction of falling number time—as radiation dose increased, their values being 397 s (0 kGy), 388 s (1 kGy), 343 s (3 kGy) and 293 s (9 kGy) respectively, remaining almost constant over the period of one month. Pan breads prepared with irradiated wheat flour showed increased weight. Texture analysis showed that bread made of irradiated flour presented an increase in maximum deformation force. The results indicate that wheat flour ionizing radiation processing may confer increased enzymatic activity on bread making and depending on the irradiation dose, an increase in weight, height and deformation force parameters of pan breads made of it.

  3. Technological characteristics of bread containing integral irradiated flours

    International Nuclear Information System (INIS)

    Teixeira, Christian A.H.M.; Mastro, Nelida L. del

    2011-01-01

    Wheat is normally used to make bread, pasta, and noodles, because among the cereal flours, only wheat flour has the ability to form cohesive dough upon hydration. For that reason, only partial substitution of wheat flour can be recommended. In this work, pan breads were prepared with 30% content of irradiated whole wheat, whole rye and coarse cornmeal and the influence of blending on bread making capabilities investigated through some technological characteristics. All-brand wheat, rye and cornmeal flours were irradiated with 0, 1, 3 and 9 kGy in a 60 Co and the deformation force, height and weight of breads prepared with those blends were then determined. Breads prepared with irradiated whole wheat flour showed an increase in the deformation force with the increase of radiation dose. The bread height presented also an increase for the doses of 1 and 3 kGy. Breads prepared with refined wheat flour blended with irradiated whole rye flour showed an increased deformation force for radiation doses of 1 and 3 kGy and an increase in weight for samples irradiated with 1 kGy. Coarse cornmeal blended flour showed a great increase of the deformation force upon irradiation, and an increase in weight for samples irradiated with 3 kGy. The results indicate that the addition of irradiated integral flour, whole wheat, whole rye flour and cornmeal to wheat flour may confer changes in physical properties beside an increment in nutritional value. (author)

  4. Restudy on digital mine: characteristics, framework and key technologies

    Energy Technology Data Exchange (ETDEWEB)

    Wu, L.; Yin, Z.; Zhong, Y. [China University of Mining and Technology, Beijing (China). Beijing Campus

    2003-02-01

    Based on analysing the problems associated with the promotion of mine digitization in China, the basic characteristics of a digital mine (DM) are described with respect to an intelligent transportation system: high speed intranet as the road-net; modular mining software as the vehicle; mine data and models as the fuel; 3D geoscience modelling (3DGM) and data mining as the filter; data collection and update as the safeguard, and mine GIS (MGIS) as the scheduler. Based on the four-layered structure of C/S and the work processes in a mine, the fundamental constituent diagram and a network framework of DM are designed. The nine key technologies for the implementation of DM strategy are discussed, which includes the data warehouse in mine; the data mining in mine; real 3DGM and visualization; 3D topological modelling and analysis in mine; modular application software and models; underground rapid positioning and automatic navigation; underground multimedia communication and wireless transmission; intelligent mining robot-groups and the integration of 3S (GIS, GPS, RS), office automation (OA) and command dispatch system (CDS). In addition, the recent progress of 'digital Kailuan' is introduced as an example of DM. 26 refs., 4 figs.

  5. Future Vehicle Technologies : high performance transportation innovations

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, T. [Future Vehicle Technologies Inc., Maple Ridge, BC (Canada)

    2010-07-01

    Battery management systems (BMS) were discussed in this presentation, with particular reference to the basic BMS design considerations; safety; undisclosed information about BMS; the essence of BMS; and Future Vehicle Technologies' BMS solution. Basic BMS design considerations that were presented included the balancing methodology; prismatic/cylindrical cells; cell protection; accuracy; PCB design, size and components; communications protocol; cost of manufacture; and expandability. In terms of safety, the presentation addressed lithium fires; high voltage; high voltage ground detection; crash/rollover shutdown; complete pack shutdown capability; and heat shields, casings, and impact protection. BMS bus bar engineering considerations were discussed along with good chip design. It was concluded that FVTs advantage is a unique skillset in automotive technology and the development of speed and cost effectiveness. tabs., figs.

  6. Multidimensional performance characteristics and standard of performance in talented youth field hockey players : A longitudinal study

    NARCIS (Netherlands)

    Elferink-Gemser, Marije T.; Visscher, Chris; Lemmink, Koen A. P. M.; Mulder, Theo

    2007-01-01

    To identify performance characteristics that could help predict future elite field hockey players, we measured the anthropometric, physiological, technical, tactical, and psychological characteristics of 30 elite and 35 sub-elite youth players at the end of three consecutive seasons. The mean age of

  7. Influence of prey body characteristics and performance on predator selection.

    Science.gov (United States)

    Holmes, Thomas H; McCormick, Mark I

    2009-03-01

    At the time of settlement to the reef environment, coral reef fishes differ in a number of characteristics that may influence their survival during a predatory encounter. This study investigated the selective nature of predation by both a multi-species predator pool, and a single common predator (Pseudochromis fuscus), on the reef fish, Pomacentrus amboinensis. The study focused on the early post-settlement period of P. amboinensis, when mortality, and hence selection, is known to be highest. Correlations between nine different measures of body condition/performance were examined at the time of settlement, in order to elucidate the relationships between different traits. Single-predator (P. fuscus) choice trials were conducted in 57.4-l aquaria with respect to three different prey characteristics [standard length (SL), body weight and burst swimming speed], whilst multi-species trials were conducted on open patch reefs, manipulating prey body weight only. Relationships between the nine measures of condition/performance were generally poor, with the strongest correlations occurring between the morphological measures and within the performance measures. During aquaria trials, P. fuscus was found to be selective with respect to prey SL only, with larger individuals being selected significantly more often. Multi-species predator communities, however, were selective with respect to prey body weight, with heavier individuals being selected significantly more often than their lighter counterparts. Our results suggest that under controlled conditions, body length may be the most important prey characteristic influencing prey survival during predatory encounters with P. fuscus. In such cases, larger prey size may actually be a distinct disadvantage to survival. However, these relationships appear to be more complex under natural conditions, where the expression of prey characteristics, the selectivity fields of a number of different predators, their relative abundance, and

  8. RELATIONSHIPS BETWEEN MUSCLE FATIGUE CHARACTERISTICS AND MARKERS OF ENDURANCE PERFORMANCE

    Directory of Open Access Journals (Sweden)

    Martyn G. Morris

    2008-12-01

    Full Text Available The aim of this study was to examine the relationship of a range of in-vivo whole muscle characteristics to determinants of endurance performance. Eleven healthy males completed a cycle ergometer step test to exhaustion for the determination of the lactate threshold, gross mechanical efficiency, peak power and VO2max. On two separate occasions, contractile and fatigue characteristics of the quadriceps femoris were collected using a specially designed isometric strength-testing chair. Muscle fatigue was then assessed by stimulating the muscle for 3 minutes. Force, rate of force development and rates of relaxation were calculated at the beginning and end of the 3 minute protocol and examined for reliability and in relation to lactate threshold, VO2max, gross mechanical efficiency and peak power. Muscle characteristics, rate of force development and relaxation rate were demonstrated to be reliable measures. Force drop off over the 3 minutes (fatigue index was related to lactate threshold (r = -0.72 p < 0.01 but not to VO2max. The rate of force development related to the peak power at the end of the cycle ergometer test (r = -0.75 p < 0.01. Rates of relaxation did not relate to any of the performance markers. We found in-vivo whole muscle characteristics, such as the fatigue index and rate of force development, relate to specific markers of peripheral, but not to central, fitness components. Our investigation suggests that muscle characteristics assessed in this way is reliable and could be feasibly utilised to further our understanding of the peripheral factors underpinning performance

  9. Acting with Technology: Rehearsing for Mixed-Media Live Performances

    DEFF Research Database (Denmark)

    Barkhuus, Louise; Rossitto, Chiara

    2016-01-01

    require a different type of engagement from the actors and rehearsing is challenging, as it can be impossible to rehearse with all the functional technology and interaction. Here, we report experiences from a case study of two mixed-media performances; we studied the rehearsal practices of two actors who......Digital technologies provide theater with new possibilities for combining traditional stage-based performances with interactive artifacts, for streaming remote parallel performances and for other device facilitated audience interaction. Compared to traditional theater, mixed-media performances...... and mixed media performances through addressing critical factors of implementing technology into rehearsal practices....

  10. Relationships between Isometric Force-Time Characteristics and Dynamic Performance

    Directory of Open Access Journals (Sweden)

    Thomas Dos’Santos

    2017-09-01

    Full Text Available The purpose of this study was to explore the relationships between isometric mid-thigh pull (IMTP force-time characteristics (peak force and time-specific force vales (100–250 ms and dynamic performance and compare dynamic performance between stronger and weaker athletes. Forty-three athletes from different sports (rowing, soccer, bicycle motocross, and hockey performed three trials of the squat jump (SJ, countermovement jump (CMJ, and IMTP, and performed a one repetition maximum power clean (PC. Reactive strength index modified (RSImod was also calculated from the CMJ. Statistically significant large correlations between IMTP force-time characteristics and PC (ρ = 0.569–0.674, p < 0.001, and moderate correlations between IMTP force-time characteristics (excluding force at 100 ms and RSImod (ρ = 0.389–0.449, p = 0.013–0.050 were observed. Only force at 250 ms demonstrated a statistically significant moderate correlation with CMJ height (ρ = 0.346, p = 0.016 and no statistically significant associations were observed between IMTP force-time characteristics and SJ height. Stronger athletes (top 10 demonstrated statistically significantly greater CMJ heights, RSImods, and PCs (p ≤ 0.004, g = 1.32–1.89 compared to weaker (bottom 10 athletes, but no differences in SJ height were observed (p = 0.871, g = 0.06. These findings highlight that the ability to apply rapidly high levels of force in short time intervals is integral for PC, CMJ height, and reactive strength.

  11. EXPERIMENTAL ANALYSIS OF THE CHARACTERISTIC PERFORMANCE OF STANDALONE PHOTOVOLTAIC SYSTEM

    OpenAIRE

    Birendra Kishore; Anirban Nandy*; O.P. Pandey

    2016-01-01

    This paper demonstrates an insight solar PV Stand Alone system which is a practical model with a halogen light source. At different situations the performance of solar PV cells are analyzed. The system produces power with depending on the change in halogen light intensity & temperature. A theoretical & experimental analysis of the PV cell can be achieved. In this paper the I-V & P-V characteristic of the solar photovoltaic cells with changes in temperature and isolation have been showed. With...

  12. Solar energy photovoltaic technology: proficiency and performance

    International Nuclear Information System (INIS)

    2006-01-01

    Total is committed to making the best possible of the planet's fossil fuel reserves while fostering the emergence of other solutions, notably by developing effective alternatives. Total involves in photovoltaics when it founded in 1983 Total Energies, renamed Tenesol in 2005, a world leader in the design and installation of photovoltaic solar power systems. This document presents Total's activities in the domain: the global challenge of energy sources and the environment, the energy collecting by photovoltaic electricity, the silicon technology for cell production, solar panels and systems to distribute energy, research and development to secure the future. (A.L.B.)

  13. PWR and WWER fuel performance. A comparison of major characteristics

    International Nuclear Information System (INIS)

    Weidinger, H.

    2006-01-01

    PWR and WWER fuel technologies have the same basic performance targets: most effective use of the energy stored in the fuel and highest possible reliability. Both fuel technologies use basically the same strategies to reach these targets: 1) Optimized reload strategies; 2) Maximal use of structural material with low neutron cross sections; 3) Decrease the fuel failure frequency towards a 'zero failure' performance by understanding and eliminating the root causes of those defects. The key driving force of the technology of both, PWR and WWER fuel is high burn-up. Presently a range of 45 - 50 MWD/kgU have been reached commercially for PWR and WWER fuel. The main technical limitations to reach high burn-up are typically different for PWR and WWER fuel: for PWR fuel it is the corrosion and hydrogen uptake of the Zr-based materials; for WWER fuel it is the mechanical and dimensional stability of the FA (and the whole core). Corrosion and hydrogen uptake of Zr-materials is a 'non-problem' for WWER fuel. Other performance criteria that are important for high burn-up are the creep and growth behaviour of the Zr materials and the fission gas release in the fuel rod. There exists a good and broad data base to model and design both fuel types. FA and fuel rod vibration appears to be a generic problem for both fuel types but with more evidence for PWR fuel performance reliability. Grid-to-rod fretting is still a major issue in the fuel failure statistics of PWR fuel. Fuel rod cladding defects by debris fretting is no longer a key problem for PWR fuel, while it still appears to be a significant root cause for WWER fuel failures. 'Zero defect' fuel performance is achievable with a high probability, as statistics for US PWR and WWER-1000 fuel has shown

  14. Gamma radiation influence on technological characteristics of wheat flour

    International Nuclear Information System (INIS)

    Teixeira, Christian A.H.M.; Inamura, Patricia Y.; Uehara, Vanessa B.; Mastro, Nelida L.d.

    2012-01-01

    This study aimed at determining the influence of gamma radiation on technological characteristics of wheat (Triticum sativum) flour and physical properties of pan breads made with this flour. The bread formulation included wheat flour, water, milk, salt, sugar, yeast and butter. The α-amylase activity of wheat flour irradiated with 1, 3 and 9 kGy in a Gammacell 220 (AECL), one day, five days and one month after irradiation was evaluated. Deformation force, height and weight of breads prepared with the irradiated flour were also determined. The enzymatic activity increased—reduction of falling number time—as radiation dose increased, their values being 397 s (0 kGy), 388 s (1 kGy), 343 s (3 kGy) and 293 s (9 kGy) respectively, remaining almost constant over the period of one month. Pan breads prepared with irradiated wheat flour showed increased weight. Texture analysis showed that bread made of irradiated flour presented an increase in maximum deformation force. The results indicate that wheat flour ionizing radiation processing may confer increased enzymatic activity on bread making and depending on the irradiation dose, an increase in weight, height and deformation force parameters of pan breads made of it. - Highlights: ► We study the influence of gamma radiation on wheat flour and properties of breads. ► Falling number decreased with radiation remaining almost constant up to one month. ► Ionizing radiation may confer an increase in texture parameters, weight and height on the bread.

  15. Quality and Characteristics of Recent Research in Technology Education

    Science.gov (United States)

    Johnson, Scott D.; Daugherty, Jenny

    2008-01-01

    The focus of research in technology education has evolved throughout its history as the field changed from industrial arts to technology education (Spencer & Rogers, 2006). With the move to technology education, the field has begun to broaden its focus to better understand the teaching, learning, curriculum, and policy implications of preparing…

  16. Irradiated fuel performance evaluation technology development

    International Nuclear Information System (INIS)

    Koo, Yang Hyun; Bang, J. G.; Kim, D. H.

    2012-01-01

    Alpha version performance code for dual-cooled annular fuel under steady state operation, so called 'DUOS', has been developed applying performance models and proposed methodology. Furthermore, nonlinear finite element module which could be integrated into transient/accident fuel performance code was also developed and evaluated using commercial FE code. The first/second irradiation and PIE test of annular pellet for dual-cooled annular fuel in the world have been completed. In-pile irradiation test DB of annular pellet up to burnup of 10,000 MWd/MTU through the 1st test was established and cracking behavior of annular pellet and swelling rate at low temperature were studied. To do irradiation test of dual-cooled annular fuel under PWR's simulating steady-state conditions, irradiation test rig/rod design/manufacture of mock-up/performance test have been completed through international collaboration program with Halden reactor project. The irradiation test of large grain pellets has been continued from 2002 to 2011 and completed successfully. Burnup of 70,000 MWd/MTU which is the highest burnup among irradiation test pellets in domestic was achieved

  17. Performance characteristics of solar air heater with surface mounted obstacles

    International Nuclear Information System (INIS)

    Bekele, Adisu; Mishra, Manish; Dutta, Sushanta

    2014-01-01

    Highlights: • Solar air heater with delta shaped obstacles have been studied. • Obstacle angle of incidence strongly affects the thermo-hydraulic performance. • Thermal performance of obstacle mounted collectors is superior to smooth collectors. • Thermo-hydraulic performance of the present SAH is higher than those in previous studies. - Abstract: The performance of conventional solar air heaters (SAHs) can be improved by providing obstacles on the heated wall (i.e. on the absorber plate). Experiments have been performed to collect heat transfer and flow-friction data from an air heater duct with delta-shaped obstacles mounted on the absorber surface and having an aspect ratio 6:1 resembling the conditions close to the solar air heaters. This study encompassed for the range of Reynolds number (Re) from 2100 to 30,000, relative obstacle height (e/H) from 0.25 to 0.75, relative obstacle longitudinal pitch (P l /e) from 3/2 to 11/2, relative obstacle transverse pitch (P t /b) from 1 to 7/3 and the angle of incidence (α) varied from 30° to 90°. The thermo-hydraulic performance characteristics of SAH have been compared with the previous published works and the optimum range of the geometries have been explored for the better performance of such air-heaters compared to the other designs of solar air heaters

  18. Model Of Emergency Department Nurse Performance Improvement Based on Association of Individual Characteristic, Organization Characteristic and Job Characteristic

    OpenAIRE

    Bogar, Maria Margaretha; Nursalam, Nursalam; Dewi, Yulis Setiya

    2017-01-01

    Introduction: Nursing care is integral part of health care and having important role in management of patient with emergency condition. The purpose of this research was to develop nurse performance improvement model based on individual, organization and job characteristics association in Emergency Department of RSUD dr TC Hillers Maumere. Method: This was an explanative survey by cross sectional approach held on July -August 2012. Respondents in this study were 22 nurses and 44 patients were ...

  19. Performance characteristics of a quantum Diesel refrigeration cycle

    International Nuclear Information System (INIS)

    He Jizhou; Wang Hao; Liu Sanqiu

    2009-01-01

    The Diesel refrigeration cycle using an ideal quantum gas as the working substance is called quantum Diesel refrigeration cycle, which is different from Carnot, Ericsson, Brayton, Otto and Stirling refrigeration cycles. For ideal quantum gases, a corrected equation of state, which considers the quantum behavior of gas particles, is used instead of the classical one. The purpose of this paper is to investigate the effect of quantum gas as the working substance on the performance of a quantum Diesel refrigeration cycle. It is found that coefficients of performance of the cycle are not affected by the quantum degeneracy of the working substance, which is the same as that of the classical Diesel refrigeration cycle. However, the refrigeration load is different from those of the classical Diesel refrigeration cycle. Lastly, the influence of the quantum degeneracy on the performance characteristics of the quantum Diesel refrigeration cycle operated in different temperature regions is discussed

  20. Performance and emission characteristics of double biodiesel blends with diesel

    Directory of Open Access Journals (Sweden)

    Kuthalingam Arun Balasubramanian

    2013-01-01

    Full Text Available Recent research on biodiesel focused on performance of single biodiesel and its blends with diesel. The present work aims to investigate the possibilities of the application of mixtures of two biodiesel and its blends with diesel as a fuel for diesel engines. The combinations of Pongamia pinnata biodiesel, Mustard oil biodiesel along with diesel (PMD and combinations of Cotton seed biodiesel, Pongamia pinnata biodiesel along with diesel (CPD are taken for the experimental analysis. Experiments are conducted using a single cylinder direct-injection diesel engine with different loads at rated 3000 rpm. The engine characteristics of the two sets of double biodiesel blends are compared. For the maximum load, the value of Specific Fuel consumption and thermal efficiency of CPD-1 blend (10:10:80 is close to the diesel values. CPD blends give better engine characteristics than PMD blends. The blends of CPD are suitable alternative fuel for diesel in stationary/agricultural diesel engines.

  1. Some performance characteristics of a fluidized bed heat recovery unit

    International Nuclear Information System (INIS)

    Militzer, J.; Basu, P.; Adaikkappan, N.

    1985-01-01

    The advantages of using fluidized bed heat recovery units with diesel engines are well documented. Two of those are: significantly less tube fouling and heat transfer coefficient four to five time higher than that of conventional shell and tube heat exchangers. The high concentration of soot in the exhaust gases of diesel engines make fouling a major concern in design of any kind of heat recovery unit. In the experiment a conventional fluidized bed heat exchanger was connected to the exhaust of a diesel engine mounted on a dynamometer. With this arrangement it was possible to test the heat recovery unit under a wide range of operating conditions. The main objective of this experiment was the determination of the performance characteristics of the heat recovery unit, especially with reference to its heat transfer and fouling characteristics. (author)

  2. Performance-Based Technology Selection Filter description report

    International Nuclear Information System (INIS)

    O'Brien, M.C.; Morrison, J.L.; Morneau, R.A.; Rudin, M.J.; Richardson, J.G.

    1992-05-01

    A formal methodology has been developed for identifying technology gaps and assessing innovative or postulated technologies for inclusion in proposed Buried Waste Integrated Demonstration (BWID) remediation systems. Called the Performance-Based Technology Selection Filter, the methodology provides a formalized selection process where technologies and systems are rated and assessments made based on performance measures, and regulatory and technical requirements. The results are auditable, and can be validated with field data. This analysis methodology will be applied to the remedial action of transuranic contaminated waste pits and trenches buried at the Idaho National Engineering Laboratory (INEL)

  3. Employees Technology Usage Adaptation Impact on Companies’ Logistics Service Performance

    Directory of Open Access Journals (Sweden)

    A. Zafer ACAR

    2018-01-01

    Full Text Available The information technology (IT capability of companies is one of the determinants of their competitive power. However, IT outputs depend on employees intentions to use them. As a technological investment Port automation systems are widely used in container terminals. Therefore behavioral intention in the usage of various IT applications is one of the important factors that may affect logistics service performance. This study aims to explore the employees' technology usage adaptation impact on the logistics service performance of ports. In this context, the behavioral intentions of employees who use port automation systems are investigated using the Technological Acceptance Model.

  4. Performance-Based Technology Selection Filter description report

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, M.C.; Morrison, J.L.; Morneau, R.A.; Rudin, M.J.; Richardson, J.G.

    1992-05-01

    A formal methodology has been developed for identifying technology gaps and assessing innovative or postulated technologies for inclusion in proposed Buried Waste Integrated Demonstration (BWID) remediation systems. Called the Performance-Based Technology Selection Filter, the methodology provides a formalized selection process where technologies and systems are rated and assessments made based on performance measures, and regulatory and technical requirements. The results are auditable, and can be validated with field data. This analysis methodology will be applied to the remedial action of transuranic contaminated waste pits and trenches buried at the Idaho National Engineering Laboratory (INEL).

  5. Performance characteristics of CdTe drift ring detector

    Science.gov (United States)

    Alruhaili, A.; Sellin, P. J.; Lohstroh, A.; Veeramani, P.; Kazemi, S.; Veale, M. C.; Sawhney, K. J. S.; Kachkanov, V.

    2014-03-01

    CdTe and CdZnTe material is an excellent candidate for the fabrication of high energy X-ray spectroscopic detectors due to their good quantum efficiency and room temperature operation. The main material limitation is associated with the poor charge transport properties of holes. The motivation of this work is to investigate the performance characteristics of a detector fabricated with a drift ring geometry that is insensitive to the transport of holes. The performance of a prototype Ohmic CdTe drift ring detector fabricated by Acrorad with 3 drift rings is reported; measurements include room temperature current voltage characteristics (IV) and spectroscopic performance. The data shows that the energy resolution of the detector is limited by leakage current which is a combination of bulk and surface leakage currents. The energy resolution was studied as a function of incident X-ray position with an X-ray microbeam at the Diamond Light Source. Different ring biasing schemes were investigated and the results show that by increasing the lateral field (i.e. the bias gradient across the rings) the active area, evaluated by the detected count rate, increased significantly.

  6. PERFORMANCE CHARACTERISTIC MEMS-BASED IMUs FOR UAVs NAVIGATION

    Directory of Open Access Journals (Sweden)

    H. A. Mohamed

    2015-08-01

    Full Text Available Accurate 3D reconstruction has become essential for non-traditional mapping applications such as urban planning, mining industry, environmental monitoring, navigation, surveillance, pipeline inspection, infrastructure monitoring, landslide hazard analysis, indoor localization, and military simulation. The needs of these applications cannot be satisfied by traditional mapping, which is based on dedicated data acquisition systems designed for mapping purposes. Recent advances in hardware and software development have made it possible to conduct accurate 3D mapping without using costly and high-end data acquisition systems. Low-cost digital cameras, laser scanners, and navigation systems can provide accurate mapping if they are properly integrated at the hardware and software levels. Unmanned Aerial Vehicles (UAVs are emerging as a mobile mapping platform that can provide additional economical and practical advantages. However, such economical and practical requirements need navigation systems that can provide uninterrupted navigation solution. Hence, testing the performance characteristics of Micro-Electro-Mechanical Systems (MEMS or low cost navigation sensors for various UAV applications is important research. This work focuses on studying the performance characteristics under different manoeuvres using inertial measurements integrated with single point positioning, Real-Time-Kinematic (RTK, and additional navigational aiding sensors. Furthermore, the performance of the inertial sensors is tested during Global Positioning System (GPS signal outage.

  7. Performance Characteristic Mems-Based IMUs for UAVs Navigation

    Science.gov (United States)

    Mohamed, H. A.; Hansen, J. M.; Elhabiby, M. M.; El-Sheimy, N.; Sesay, A. B.

    2015-08-01

    Accurate 3D reconstruction has become essential for non-traditional mapping applications such as urban planning, mining industry, environmental monitoring, navigation, surveillance, pipeline inspection, infrastructure monitoring, landslide hazard analysis, indoor localization, and military simulation. The needs of these applications cannot be satisfied by traditional mapping, which is based on dedicated data acquisition systems designed for mapping purposes. Recent advances in hardware and software development have made it possible to conduct accurate 3D mapping without using costly and high-end data acquisition systems. Low-cost digital cameras, laser scanners, and navigation systems can provide accurate mapping if they are properly integrated at the hardware and software levels. Unmanned Aerial Vehicles (UAVs) are emerging as a mobile mapping platform that can provide additional economical and practical advantages. However, such economical and practical requirements need navigation systems that can provide uninterrupted navigation solution. Hence, testing the performance characteristics of Micro-Electro-Mechanical Systems (MEMS) or low cost navigation sensors for various UAV applications is important research. This work focuses on studying the performance characteristics under different manoeuvres using inertial measurements integrated with single point positioning, Real-Time-Kinematic (RTK), and additional navigational aiding sensors. Furthermore, the performance of the inertial sensors is tested during Global Positioning System (GPS) signal outage.

  8. Performance and emissions characteristics of biodiesel from soybean oil

    Energy Technology Data Exchange (ETDEWEB)

    Canakci, M. [Kocaeli University, Izmit (Turkey). Faculty of Technical Education

    2005-07-15

    Biodiesel is an alternative diesel fuel that can be produced from renewable feedstocks such as vegetable oils, waste frying oils, and animal fats. It is an oxygenated, non-toxic, sulphur-free, biodegradable, and renewable fuel. Many engine manufacturers have included this fuel in their warranties since it can be used in diesel engines without significant modification. However, the fuel properties such as cetane number, heat of combustion, specific gravity, and kinematic viscosity affect the combustion, engine performance and emission characteristics. In this study, the engine performance and emissions characteristics of two different petroleum diesel fuels (No. 1 and No. 2 diesel fuels) and biodiesel from soybean oil and its 20 per cent blends with No. 2 diesel fuel were compared. The results showed that the engine performance of the neat biodiesel and its blend was similar to that of No. 2 diesel fuel with nearly the same brake fuel conversion efficiency, and slightly higher fuel consumption. CO{sub 2} emission for the biodiesel was slightly higher than for the No. 2 diesel fuel. Compared with diesel fuels, biodiesel produced lower exhaust emissions, except NO{sub x}. (author)

  9. Improvement of Supply Chain Performances Using RFID Technology

    OpenAIRE

    Turcu, Cornel; Turcu, Cristina; Graur, Adrian

    2009-01-01

    This chapter helps to improve readers understanding of the RFID and EPC potential for business processes. RFID technology is classified as a wireless AIDC technology that uses digital data encoded into a radio tag embedding a microchip with an antenna. The data stored on the tag is collected by a reader using radio waves. There are a large variety of RFID tags designs; they also have many different functional characteristics such as power source, carrier frequency, read range, data storage ca...

  10. Breeder design for enhanced performance and safety characteristics

    International Nuclear Information System (INIS)

    Fischer, G.J.; Atefi, B.; Yang, J.W.; Galperin, A.; Segev, M.

    1980-01-01

    A fast breeder reactor design has been created which offers a considerably extended fuel cycle and excellent performance characteristics. An example of a core designed to operate on a ten-year fuel cycle is described in some detail. Use of metal fuel along with a moderator such as beryllium oxide dispersed throughout the core provides both design flexibility and safety advantages such as a strong Doppler feedback and limited sodium void reactivity gain. Local power variations are small for the entire cycle; control requirements are also modest, and fuel cycle costs are low

  11. Performance characteristics of the DIII-D advanced divertor cryopump

    International Nuclear Information System (INIS)

    Menon, M.M.; Maingi, R.; Wade, M.R.; Baxi, C.B.; Campbell, G.L.; Holtrop, K.L.; Hyatt, A.W.; Laughon, G.J.; Makariou, C.C.; Mahdavi, M.A.; Reis, E.E.; Schaffer, M.J.; Schaubel, K.M.; Scoville, J.T.; Smith, J.P.; Stambaugh, R.D.

    1993-10-01

    A cryocondensation pump, cooled by forced flow of two-phase helium, has been installed for particle exhaust from the divertor region of the DIII-D tokamak. The Inconel pumping surface is of coaxial geometry, 25.4 mm in outer diameter and 11.65 m in length. Because of the tokamak environment, the pump is designed to perform under relatively high pulsed heat loads (300 Wm -2 ). Results of measurements made on the pumping characteristics for D 2 , H 2 , and Ar are discussed

  12. Performance Analyses in an Assistive Technology Service Delivery Process

    DEFF Research Database (Denmark)

    Petersen, Anne Karin

    Performance Analyses in an Assistive Technology Service Delivery Process.Keywords: process model, occupational performance, assistive technologiesThe Poster is about teaching students, using models and theory in education and practice. It is related to Occupational therapy process and professional...... af top-til-bund, klientcentreret og aktivitetsbaseret interventioner, ERGO/MunksgaardFisher, A. &, Griswold, L. A., 2014. Performance Skills. I: B.Schell red.2014 Occupational Therapy. Willard &Spackman’s occupational therapy. -12th ed., p.249-264Cook A.M., Polgar J.M. (2015) Assistive Technologies...

  13. High performance nano-composite technology development

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D. [KAERI, Taejon (Korea, Republic of); Kim, E. K.; Jung, S. Y.; Ryu, H. J. [KRICT, Taejon (Korea, Republic of); Hwang, S. S.; Kim, J. K.; Hong, S. M. [KIST, Taejon (Korea, Republic of); Chea, Y. B. [KIGAM, Taejon (Korea, Republic of); Choi, C. H.; Kim, S. D. [ATS, Taejon (Korea, Republic of); Cho, B. G.; Lee, S. H. [HGREC, Taejon (Korea, Republic of)

    1999-06-15

    The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

  14. High performance nano-composite technology development

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D. [KAERI, Taejon (Korea, Republic of); Kim, E. K.; Jung, S. Y.; Ryu, H. J. [KRICT, Taejon (Korea, Republic of); Hwang, S. S.; Kim, J. K.; Hong, S. M. [KIST, Taejon (Korea, Republic of); Chea, Y. B. [KIGAM, Taejon (Korea, Republic of); Choi, C. H.; Kim, S. D. [ATS, Taejon (Korea, Republic of); Cho, B. G.; Lee, S. H. [HGREC, Taejon (Korea, Republic of)

    1999-06-15

    The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

  15. High performance nano-composite technology development

    International Nuclear Information System (INIS)

    Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D.; Kim, E. K.; Jung, S. Y.; Ryu, H. J.; Hwang, S. S.; Kim, J. K.; Hong, S. M.; Chea, Y. B.; Choi, C. H.; Kim, S. D.; Cho, B. G.; Lee, S. H.

    1999-06-01

    The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

  16. High Performance Fuel Technology Development(I)

    International Nuclear Information System (INIS)

    Song, Kun Woo; Kim, Keon Sik; Bang, Jeong Yong; Park, Je Keon; Chen, Tae Hyun; Kim, Hyung Kyu

    2010-04-01

    The dual-cooled annular fuel has been investigated for the purpose of achieving the power uprate of 20% and decreasing pellet temperature by 30%. The 12x12 rod array and basic design was developed, which is mechanically compatible with the OPR-1000. The reactor core analysis has been performed using this design, and the results have shown that the criteria of nuclear, thermohydraulic and safety design are satisfied and pellet temperature can be lowered by 40% even in 120% power. The basic design of fuel component was developed and the cladding thickness was designed through analysis and experiments. The solutions have been proposed and analyzed to the technical issues such as 'inner channel blockage' and 'imbalance between inner and outer coolant'. The annular pellet was fabricated with good control of shape and size, and especially, a new sintering technique has been developed to control the deviation of inner diameter within ±5μm. The irradiation test of annular pellets has been conducted up to 10 MWD/kgU to find out the densification and swelling behaviors. The 11 types of materials candidates have developed for the PCI-endurance pellet, and the material containing the Mn-Al additive showed its creep performance of much better than UO2 material. The HANA cladding has been irradiated up to 61 MWD/kgU, and the results have shown that its oxidation resistance is better by 40% than that of Zircaloy. The 30 types of candidate materials for next generation have been developed through alloy design and property tests

  17. Elucidate Innovation Performance of Technology-driven Mergers and Acquisitions

    Energy Technology Data Exchange (ETDEWEB)

    Huang, L.; Wang, K.; Yu, H.; Shang, L.; Mitkova, L.

    2016-07-01

    The importance and value of Mergers and Acquisitions (M&As) have increased with the expectancy to obtain key technology capabilities and rapid impact on innovation. This article develops an original analytical framework to elucidate the impact of the technology and product relatedness (similarity/complementarity) of the Technology-driven M&A’ partners on post-innovation performance. We present results drawing on a multiple case studies of Chinese High-Tech firms from three industries. (Author)

  18. [The characteristics of medical technologies in emergency medical care hospital].

    Science.gov (United States)

    Murakhovskiĭ, A G; Babenko, A I; Bravve, Iu I; Tataurova, E A

    2013-01-01

    The article analyzes the implementation of major 12 diagnostic and 17 treatment technologies applied during medical care of patients with 12 key nosology forms of diseases in departments of the emergency medical care hospital No 2 of Omsk. It is established that key groups of technologies in the implementation of diagnostic process are the laboratory clinical diagnostic analyses and common diagnostic activities at reception into hospital and corresponding departments. The percentage of this kind of activities is about 78.3% of all diagnostic technologies. During the realization of treatment process the priority technologies are common curative and rehabilitation activities, intensive therapy activities and clinical diagnostic monitoring activities. All of them consist 80.1% of all curative technologies.

  19. Base technology development of new materials for FBR performance innovations

    International Nuclear Information System (INIS)

    Kano, Shigeki; Koyama, Masahiro; Nomura, Shigeo; Morikawa, Satoru; Ueno, Fumiyoshi

    1989-01-01

    This paper describes the base technology development of new materials for FBR performance innovations at the Power Reactor and Nuclear Fuel Development Corporation. The contents are as follows: (1) development of sodium and radiation resistant new materials, (2) development of high performance shielding material, (3) development of high performance control material, (4) development of new functional materials for reactor instrumentation. (author)

  20. Improved Laser performance through Planar Waveguide Technology Development

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose a laser technology development to improve efficiency and performance for a variety of science applications including: Lunar Ice, 2-Step Laser Tandem Mass...

  1. Enhanced Performance of Recycled Aggregate Concrete with Atomic Polymer Technology

    Science.gov (United States)

    2012-06-01

    The atomic polymer technology in form of mesoporous inorganic polymer (MIP) can effectively improve material durability and performance of concrete by dramatically increase inter/intragranular bond strength of concrete at nano-scale. The strategy of ...

  2. Board Characteristics and Firm Performance: Evidence from Indonesia

    Directory of Open Access Journals (Sweden)

    Athalia Ariati Hidayat

    2015-12-01

    Full Text Available This research examines the effect of board characteristics (comprising in different sized proportions: family commissioners, family directors, independent commissioners, ex-government officer commissioners, and board of commissioners size to firm performance. Using fixed-effects data panel regression, this research investigates 293 firms listed on the Indonesian Stock Exchange during 2008-2012. Firm performance is proxied by market measure (Tobin’s Q and accounting measure (ROA. The findings of this research suggest that the proportion of family commissioners and family directors have positive impact only to Tobin’s Q value, while the proportion of independent directors can increase both Tobin’s Q and ROA. On the other hand, this research finds that the proportion of ex-government officers in the board gives no impact to firm performance. This research also finds that the board size has U-shaped non-linear relationship with firm performance as proxied by Tobin’s Q and ROA.

  3. Firm performance: The role of CEOs' emotional and cognitive characteristics

    Directory of Open Access Journals (Sweden)

    Kleanthis K. Katsaros

    2015-08-01

    Full Text Available The paper examines the relationships between CEOs’ personal traits, emotions, attitudes and tolerance of ambiguity; and subsequently, the influence of CEOs’ ambiguity tolerance in firms' performance. Design/methodology/approach – Survey data were collected from 256 ICT firms established in Greece. Their CEOs completed questionnaires examining TOA, personal traits, emotions and attitudes in the workplace. Principal components analysis and ordinary least-squares regressions were used to explore the hypotheses of the paper. Findings – Three factors characterize CEOs' emotions, namely pleasure, dominance and arousal; two factors their involvement, namely importance and interest; and, respectively, one their emotional intelligence namely, empathy/handling relationships. Further, locus of control; importance; arousal; empathy/handling relationships and interest affect decisively CEOs' tolerance of ambiguity, which in turn, seems to influence positively firms' performance. Research limitations/implications – Further research is required in Greek ICT industry regarding the influence of CEOs' emotional and cognitive attributes in organizations' financial performance. Likewise, this research should be expanded to other industries. Originality/value – The originality of this study lies in the finding that emotional and cognitive characteristics affect CEOs' TOA, which, in turn, influences significantly firms' performance. Another significant contributing factor is that the study is carried out in Greece, where few studies have been conducted in this area.

  4. ASSESSING INDIVIDUAL PERFORMANCE ON INFORMATION TECHNOLOGY ADOPTION: A NEW MODEL

    OpenAIRE

    Diah Hari Suryaningrum

    2012-01-01

    This paper aims to propose a new model in assessing individual performance on information technology adoption. The new model to assess individual performance was derived from two different theories: decomposed theory of planned behavior and task-technology fit theory. Although many researchers have tried to expand these theories, some of their efforts might lack of theoretical assumptions. To overcome this problem and enhance the coherence of the integration, I used a theory from social scien...

  5. Drivers of international performance of Brazilian technology-based firms

    OpenAIRE

    Serpa Fagundes de Oliveira, Maria Carolina; Scherer, Flavia Luciane; Schneider Hahn, Ivanete; de Moura Carpes, Aletéia; Brachak dos Santos, Maríndia; Nunes Piveta, Maíra

    2018-01-01

    For Technology-Based Firms, international expansion represents an opportunity for growth and value creation. The present study was designed to analyze the role of technology-based companies (TBCs) internationalization drivers on international performance. Therefore, a descriptive research was carried out with a quantitative approach performed through a survey. Data collection happened with 53 Brazilian TBCs located in innovation habitats. These data were analyzed by multivariate statistical t...

  6. Effect of information and communication technology on nursing performance.

    Science.gov (United States)

    Fujino, Yuriko; Kawamoto, Rieko

    2013-05-01

    The aim of this study was to investigate the influence of information and communication technology use and skills on nursing performance. Questionnaires were prepared relating to using the technology, practical skills in utilizing information, the Six-Dimension Scale of Nursing Performance, and demographics. In all, 556 nurses took part (response rate, 72.6%). A two-way analysis of variance was used to determine the influence of years of nursing experience on the relationship between nursing performance and information and communication technology use. The results showed that the group possessing high technological skills had greater nursing ability than the group with low skills; the level of nursing performance improved with years of experience in the former group, but not in the latter group. Regarding information and communication technology use, the results showed that nursing performance improved among participants who used computers for sending and receiving e-mails, but it decreased for those who used cell phones for e-mail. The results suggest that nursing performance may be negatively affected if information and communication technology are inappropriately used. Informatics education should therefore be provided for all nurses, and it should include information use relating to cell phones and computers.

  7. Performance characteristics of a continuous-flow fluidic pump

    International Nuclear Information System (INIS)

    Robinson, S.M.; Counce, R.M.; Smith, G.V.

    1987-01-01

    The fluidic pump is a type of positive-displacement pump in which basic fluid mechanics phenomena are utilized to eliminate valves and other moving parts that are exposed to the fluid being transferred. The version described in this article is powered by gas pressure serving as gas pistons and is virtually maintenance-free. It utilizes two displacement vessels and is designed to produce a steady and continuous liquid flow. This type of pump may be very useful for the transfer of radioactive or hazardous liquids where mechanical maintenance may be difficult or exposure of personnel to the fluid is undesirable. This paper presents experimental and model-predicted characteristics of such systems. The effects of several geometric parameters and operating conditions on the performance of the pump are briefly discussed

  8. Roasted sesame hulls improve broiler performance without affecting carcass characteristics

    Directory of Open Access Journals (Sweden)

    Kamel Z. Mahmoud

    2015-09-01

    Full Text Available An experiment was conducted to evaluate the effect of using graded levels of roasted sesame hulls (RSH on growth performance and meat quality characteristics in broiler chickens. A total of 360 day-old Lohmann chicks were randomly allocated into 24 floor pens and raised over 42 days. One of four dietary treatments was assigned to each group of six pens in a completely randomized fashion. The chicks in the control group were fed a corn-soybean based diet (RSH-0, while the chicks in treatments two, three, and four were fed graded levels of RSH at 4% (RSH-4, 8% (RSH-8, and 12% (RSH-12, respectively. Diets were formulated to meet broiler chicks’ requirements according to the National Research Council for both starter and finisher rations. The results showed that RSH inclusion increased (P<0.05 feed intake and final body weight without adversely affecting the feed conversion ratio. Broiler chicks fed RSH-12 had heavier (P<0.05 breast and leg cuts compared to the control-fed group with no change to their chemical composition. Water holding capacity (WHC, cooking loss (CL, and shear force (SF reported similar results in all dietary groups. The chemical composition of both thigh and breast cuts was not affected by the RSH. After one day of thawing, colour coordinates of breast cuts behaved similarly in all dietary groups. The results of this study suggest that the addition of RSH to broiler diets up to 12% improves their growth performance; nevertheless, carcass characteristics and meat quality showed no alterations compared to the control-fed group.

  9. Performance of active vibration control technology: the ACTEX flight experiments

    Science.gov (United States)

    Nye, T. W.; Manning, R. A.; Qassim, K.

    1999-12-01

    This paper discusses the development and results of two intelligent structures space-flight experiments, each of which could affect architecture designs of future spacecraft. The first, the advanced controls technology experiment I (ACTEX I), is a variable stiffness tripod structure riding as a secondary payload on a classified spacecraft. It has been operating well past its expected life since becoming operational in 1996. Over 60 on-orbit experiments have been run on the ACTEX I flight experiment. These experiments form the basis for in-space controller design problems and for concluding lifetime/reliability data on the active control components. Transfer functions taken during the life of ACTEX I have shown consistent predictability and stability in structural behavior, including consistency with those measurements taken on the ground prior to a three year storage period and the launch event. ACTEX I can change its modal characteristics by employing its dynamic change mechanism that varies preloads in portions of its structure. Active control experiments have demonstrated maximum vibration reductions of 29 dB and 16 dB in the first two variable modes of the system, while operating over a remarkable on-orbit temperature range of -80 °C to 129 °C. The second experiment, ACTEX II, was successfully designed, ground-tested, and integrated on an experimental Department of Defense satellite prior to its loss during a launch vehicle failure in 1995. ACTEX II also had variable modal behavior by virtue of a two-axis gimbal and added challenges of structural flexibility by being a large deployable appendage. Although the loss of ACTEX II did not provide space environment experience, ground testing resulted in space qualifying the hardware and demonstrated 21 dB, 14 dB, and 8 dB reductions in amplitude of the first three primary structural modes. ACTEX II could use either active and/or passive techniques to affect vibration suppression. Both experiments trailblazed

  10. Characteristics Contributing to High-Technology Start-Up Success

    DEFF Research Database (Denmark)

    Goslin, L.; Brown, W.; Palm, T.

    1993-01-01

    that the professional venture-capital-funded start-up firm will generally reflect the practices of perceptive management regarding: style, team approach, structure of the firm, market definition, culture, vision, and a formal strategy. Nevertheless, there are some questions about differences those characteristics...... by interview to provide insights on: the entrepreneurial-marketing style utilized, cultural characteristics of the firm, and perspectives of the time horizon of strategy. The representative firms (seven firms to a set) from whom information was solicited were drawn from the U.S. Pacific Northwest), Denmark...

  11. Improving Operational Risk Management Using Business Performance Management Technologies

    OpenAIRE

    Bram Pieket Weeserik; Marco Spruit

    2018-01-01

    Operational Risk Management (ORM) comprises the continuous management of risks resulting from: human actions, internal processes, systems, and external events. With increasing requirements, complexity and a growing volume of risks, information systems provide benefits for integrating risk management activities and optimizing performance. Business Performance Management (BPM) technologies are believed to provide a solution for effective Operational Risk Management by offering several combined ...

  12. U.S. report on fuel performance and technology

    Energy Technology Data Exchange (ETDEWEB)

    Cook, T [Department of Energy, Washington, DC (United States). Office of Engineering and Technology Development

    1997-12-01

    The report reviews the following aspects of fuel performance and technology: increased demand on fuel performance;improved fuel failure rate; operating fuel cycles; capacity factor for US nuclear electric generating plants; potential reduction of SNF due to improved fuel burnup.

  13. Improving Operational Risk Management Using Business Performance Management Technologies

    Directory of Open Access Journals (Sweden)

    Bram Pieket Weeserik

    2018-02-01

    Full Text Available Operational Risk Management (ORM comprises the continuous management of risks resulting from: human actions, internal processes, systems, and external events. With increasing requirements, complexity and a growing volume of risks, information systems provide benefits for integrating risk management activities and optimizing performance. Business Performance Management (BPM technologies are believed to provide a solution for effective Operational Risk Management by offering several combined technologies including: work flow, data warehousing, (advanced analytics, reporting and dashboards. BPM technologies can be integrated with an organization’s Planning & Control cycle and related to strategic objectives. This manuscript aims to show how ORM can benefit from BPM technologies via the development and practical validation of a new maturity model. The B4ORM maturity model was developed following the Design Science Research approach. The maturity model relates specific maturity levels of ORM processes with BPM technologies applicable for a specific maturity stage. There appears to be a strong relationship (0.78 with ORM process maturity and supporting BPM technologies. The B4ORM maturity model as described in this manuscript provides an ideal path of BPM technologies related to six distinctive stages of ORM, leading towards technologies suitable for continuous improvement of ORM processes and organization-wide integration.

  14. Development of technology performance specifications for volatile organic compounds

    International Nuclear Information System (INIS)

    Purdy, C.; Schutte, W.E.

    1993-01-01

    The Office of Technology Development (OTD) within the Office of Environmental Restoration and Waste Management of the Department of Energy has a mission to deliver needed and usable technologies to its customers. The primary customers are individuals and organizations performing environmental characterization and remediation, waste cleanup, and pollution prevention at DOE sites. DOE faces a monumental task in cleaning up the dozen or so major sites and hundreds of smaller sites that were or are used to produce the US nuclear weapons arsenal and to develop nuclear technologies for national defense and for peaceful purposes. Contaminants and waste materials include the radionuclides associated with nuclear weapons, such as plutonium and tritium, and more common pollutants and wastes of industrial activity such as chromium, chlorinated solvents, and polychlorinated biphenyls (PCBs). Quite frequently hazardous wastes regulated by the Environmental Protection Agency are co-mingled with radioactive wastes regulated by the Nuclear Regulatory Commission to yield a open-quotes mixed waste,close quotes which increases the cleanup challenges from several perspectives. To help OTD and its investigators meet DOE's cleanup goal, technology performance specifications are being implemented for research and development and DT ampersand E projects. Technology performance specifications or open-quotes performance goalsclose quotes describe, quantitatively where possible, the technology development needs being addressed. These specifications are used to establish milestones, evaluate the status of ongoing projects, and determine the success of completed projects

  15. Performance characteristics of counter flow wet cooling towers

    International Nuclear Information System (INIS)

    Khan, Jameel-Ur-Rehman; Yaqub, M.; Zubair, Syed M.

    2003-01-01

    Cooling towers are one of the biggest heat and mass transfer devices that are in widespread use. In this paper, we use a detailed model of counter flow wet cooling towers in investigating the performance characteristics. The validity of the model is checked by experimental data reported in the literature. The thermal performance of the cooling towers is clearly explained in terms of varying air and water temperatures, as well as the driving potential for convection and evaporation heat transfer, along the height of the tower. The relative contribution of each mode of heat transfer rate to the total heat transfer rate in the cooling tower is established. It is demonstrated with an example problem that the predominant mode of heat transfer is evaporation. For example, evaporation contributes about 62.5% of the total rate of heat transfer at the bottom of the tower and almost 90% at the top of the tower. The variation of air and water temperatures along the height of the tower (process line) is explained on psychometric charts

  16. Transonic Performance Characteristics of Several Jet Noise Suppressors

    Science.gov (United States)

    Schmeer, James W.; Salters, Leland B., Jr.; Cassetti, Marlowe D.

    1960-01-01

    An investigation of the transonic performance characteristics of several noise-suppressor configurations has been conducted in the Langley 16-foot transonic tunnel. The models were tested statically and over a Mach number range from 0.70 to 1.05 at an angle of attack of 0 deg. The primary jet total-pressure ratio was varied from 1.0 (jet off) to about 4.5. The effect of secondary air flow on the performance of two of the configurations was investigated. A hydrogen peroxide turbojet-engine simulator was used to supply the hot-jet exhaust. An 8-lobe afterbody with centerbody, short shroud, and secondary air had the highest thrust-minus-drag coefficients of the six noise-suppressor configurations tested. The 12-tube and 12-lobe afterbodies had the lowest internal losses. The presence of an ejector shroud partially shields the external pressure distribution of the 8-lobe after-body from the influence of the primary jet. A ring-airfoil shroud increased the static thrust of the annular nozzle but generally decreased the thrust minus drag at transonic Mach numbers.

  17. Performance and cavitation characteristics of bi-directional hydrofoils

    Science.gov (United States)

    Nedyalkov, Ivaylo; Wosnik, Martin

    2013-11-01

    Tidal turbines extract energy from flows which reverse direction. One way to address this bi-directionality in horizontal axis turbines that avoid the use of complex and maintenance-intensive yaw or blade pitch mechanisms, is to design bi-directional blades which perform (equally) well in either flow direction. A large number of proposed hydrofoil designs were investigated using numerical simulations. Selected candidate foils were also tested (at various speeds and angles of attack) in the High-Speed Cavitation Tunnel (HICaT) at the University of New Hampshire. Lift and drag were measured using a force balance, and cavitation inception and desinence were recorded. Experimental and numerical results were compared, and the foils were compared to each other and to reference foils. Bi-directional hydrofoils may provide a feasible solution to the problem of reversing flow direction, when their performance and cavitation characteristics are comparable to those for unidirectional foils, and the penalty in decreased energy production is outweighed by the cost reduction due to lower complexity and respectively lower installation and maintenance costs.

  18. An exploratory study on the determinants of performance in regional industry technology development programs

    Directory of Open Access Journals (Sweden)

    Choo-Hui Park

    2017-08-01

    Full Text Available Purpose - The purpose of this paper is to analyze the determinants of the performance of regional industrial technology development programs among the regional strategic industrial development program that the central government and Daegu metropolitan city jointly promoted between 2004 and 2012. Specifically, in this research, the authors are trying to identify the effects of R&D capabilities and technical development tasks on technological and managerial performance. Design/methodology/approach - The dependent variables of this study are technical and economic performance. Technical performance, product and process innovation, economic performance, sales and export increases were measured using five-point Likert scales. The authors added the contribution of sales through technology development to economic performance. The independent variable is the company’s R&D capability, measured by the number of R&D staff compared to the average total number of employees from 2004 to 2012. The characteristics of the technology development tasks were measured by technical characteristics, market characteristics and collaborative research types. The technological characteristics were measured by seven factors, including technological change, technical difficulty, potential in commercialization, competition between domestic and foreign competitors, difficulty in introducing overseas technology and the technological gap. Market characteristics were largely divided into complexity, dynamics and competitiveness. The types of collaborative research were divided into whether or not there were collaborative research with the participation of large corporations. The control variables are firm size (number of employees and firm age. Regression analysis was used to analyze the determinants of performance, and a difference analysis was conducted to determine the effect of collaborative research on performance. Findings - The main determinants of the regional

  19. Performance characteristics of a Kodak computed radiography system.

    Science.gov (United States)

    Bradford, C D; Peppler, W W; Dobbins, J T

    1999-01-01

    The performance characteristics of a photostimulable phosphor based computed radiographic (CR) system were studied. The modulation transfer function (MTF), noise power spectra (NPS), and detective quantum efficiency (DQE) of the Kodak Digital Science computed radiography (CR) system (Eastman Kodak Co.-model 400) were measured and compared to previously published results of a Fuji based CR system (Philips Medical Systems-PCR model 7000). To maximize comparability, the same measurement techniques and analysis methods were used. The DQE at four exposure levels (30, 3, 0.3, 0.03 mR) and two plate types (standard and high resolution) were calculated from the NPS and MTF measurements. The NPS was determined from two-dimensional Fourier analysis of uniformly exposed plates. The presampling MTF was determined from the Fourier transform (FT) of the system's finely sampled line spread function (LSF) as produced by a narrow slit. A comparison of the slit type ("beveled edge" versus "straight edge") and its effect on the resulting MTF measurements was also performed. The results show that both systems are comparable in resolution performance. The noise power studies indicated a higher level of noise for the Kodak images (approximately 20% at the low exposure levels and 40%-70% at higher exposure levels). Within the clinically relevant exposure range (0.3-3 mR), the resulting DQE for the Kodak plates ranged between 20%-50% lower than for the corresponding Fuji plates. Measurements of the presampling MTF with the two slit types have shown that a correction factor can be applied to compensate for transmission through the relief edges.

  20. Performance and flow characteristics of MHD seawater thruster

    Energy Technology Data Exchange (ETDEWEB)

    Doss, E.D.

    1990-01-01

    The main goal of the research is to investigate the effects of strong magnetic fields on the electrical and flow fields inside MHD thrusters. The results of this study is important in the assessment of the feasibility of MHD seawater propulsion for the Navy. To accomplish this goal a three-dimensional fluid flow computer model has been developed and applied to study the concept of MHD seawater propulsion. The effects of strong magnetic fields on the current and electric fields inside the MHD thruster and their interaction with the flow fields, particularly those in the boundary layers, have been investigated. The results of the three-dimensional computations indicate that the velocity profiles are flatter over the sidewalls of the thruster walls in comparison to the velocity profiles over the electrode walls. These nonuniformities in the flow fields give rise to nonuniform distribution of the skin friction along the walls of the thrusters, where higher values are predicted over the sidewalls relative to those over the electrode walls. Also, a parametric study has been performed using the three-dimensional MHD flow model to analyze the performance of continuous electrode seawater thrusters under different operating parameters. The effects of these parameters on the fluid flow characteristics, and on the thruster efficiency have been investigated. Those parameters include the magnetic field (10--20 T), thruster diameter, surface roughness, flow velocity, and the electric load factor. The results show also that the thruster performance improves with the strength of the magnetic field and thruster diameter, and the efficiency decreases with the flow velocity and surface roughness.

  1. Multijunction Photovoltaic Technologies for High-Performance Concentrators: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    McConnell, R.; Symko-Davies, M.

    2006-05-01

    Multijunction solar cells provide high-performance technology pathways leading to potentially low-cost electricity generated from concentrated sunlight. The National Center for Photovoltaics at the National Renewable Energy Laboratory has funded different III-V multijunction solar cell technologies and various solar concentration approaches. Within this group of projects, III-V solar cell efficiencies of 41% are close at hand and will likely be reported in these conference proceedings. Companies with well-developed solar concentrator structures foresee installed system costs of $3/watt--half of today's costs--within the next 2 to 5 years as these high-efficiency photovoltaic technologies are incorporated into their concentrator photovoltaic systems. These technology improvements are timely as new large-scale multi-megawatt markets, appropriate for high performance PV concentrators, open around the world.

  2. Business Performance Measurements in Asset Management with the Support of Big Data Technologies

    Science.gov (United States)

    Campos, Jaime; Sharma, Pankaj; Jantunen, Erkki; Baglee, David; Fumagalli, Luca

    2017-09-01

    The paper reviews the performance measurement in the domain of interest. Important data in asset management are further, discussed. The importance and the characteristics of today's ICTs capabilities are also mentioned in the paper. The role of new concepts such as big data and data mining analytical technologies in managing the performance measurements in asset management are discussed in detail. The authors consequently suggest the use of the modified Balanced Scorecard methodology highlighting both quantitative and qualitative aspects, which is crucial for optimal use of the big data approach and technologies.

  3. Differences in daily disposable circle lens performance characteristics

    Directory of Open Access Journals (Sweden)

    Schafer JM

    2014-04-01

    Full Text Available Jeffery M Schafer, William T Reindel, Marjorie J Rah, Osbert Chan, Lening Zhang Bausch & Lomb Incorporated, Rochester, NY, USA Purpose: The purpose of this evaluation was to compare the performance characteristics of two cosmetically tinted contact lenses in the circle lens category that differ in lens design, lens material, and pigment print pattern: etafilcon A (1-Day Acuvue Define; Johnson & Johnson Vision Care and hilafilcon B (Naturelle; Bausch & Lomb Incorporated. Methods: Two hundred Asian subjects (400 eyes were enrolled in this 1-month parallel, bilateral, randomized study at ten investigative sites. Study lenses were dispensed at a screening/dispensing visit, and follow-up visits occurred at 2 weeks and 1 month. Lenses were worn on a daily disposable basis. Fit characteristics were evaluated at each visit, and slit-lamp evaluations were completed at each follow-up visit. Results: Of the 200 patients enrolled, 172 (344 eyes completed the study. The proportion of eyes with fully centered lenses was statistically significantly higher for the hilafilcon B group at the 2-week and 1-month visits, P<0.05. Over all visits, 0.6% of hilafilcon B eyes demonstrated incomplete corneal coverage, whereas for the etafilcon A group, 8.5% of eyes demonstrated incomplete corneal coverage and/or edge lift. The proportion of eyes with adequate lens movement was statistically significantly higher for the hilafilcon B group, P<0.05. Over all visits, none of the hilafilcon B eyes was reported to have excessive movement, whereas for etafilcon A lenses, 10.2% of eyes were reported to have excessive movement. Conclusions: Etafilcon A lenses were significantly less likely to be fully centered and significantly more likely to have incomplete corneal coverage and/or edge lift compared with the hilafilcon B lenses. Keywords: cosmetic contact lens, circle contact lens

  4. Improving reservoir performance using new 'smart' well technology

    International Nuclear Information System (INIS)

    Roggensack, W.D.; Matthews, C.M.

    1997-01-01

    The technologies that were available in the past to improve reservoir performance include 3-D seismic, coiled tubing, horizontal wells, and PCP's. Future enabling technologies will also include multi-lateral wells, 'smart' wells, underbalanced drilling, and downhole fluids processing. A description of 'smart' well technology was given, defined as well completions which facilitate downhole monitoring and control of production to achieve maximum reserves recovery. The current development for 'smart' wells is focused on offshore and subsea wells for marginal field development and work-over mitigation, with the emphasis in system design for production control of horizontal and multi-lateral wells. Basic 'smart' well configuration, instrumentation and monitoring systems, applications of 'smart' well technology in the Western Canadian Sedimentary Basin, and future developments and applications for the technology in general, were also discussed. 30 figs

  5. Technology, labor characteristics and wage-productivity gaps

    OpenAIRE

    Ilmakunnas, Pekka; Maliranta, Mika

    2003-01-01

    We use plant-level linked employer-employee data from Finland to estimate production functions where also employee characteristics (average age and education, and sex composition) are included. We also estimate similar models for wages to examine whether wages are based on productivity. Our aim is to explain productivity besides manufacturing, also in services. For the service sector plants, no data on capital input, working hours, or value added is available, and productivity has to be measu...

  6. Teaching Machines, Programming, Computers, and Instructional Technology: The Roots of Performance Technology.

    Science.gov (United States)

    Deutsch, William

    1992-01-01

    Reviews the history of the development of the field of performance technology. Highlights include early teaching machines, instructional technology, learning theory, programed instruction, the systems approach, needs assessment, branching versus linear program formats, programing languages, and computer-assisted instruction. (LRW)

  7. Development of oxygen sensing technology in an irradiated fuel rod. Characteristic test of oxygen sensor

    International Nuclear Information System (INIS)

    Saito, Junichi; Hoshiya, Taiji; Sakurai, Fumio; Sakai, Haruyuki

    1996-03-01

    At the Department of JMTR (Japan Materials Test Reactor), the re-instrumentation technologies to a high burnup fuel rod irradiated in an LWR have been developed to study irradiation behavior of the fuel during power transient. It has been progressed developing a chemical sensor as one of the re-instrumentation technologies. This report summarizes the results of characteristic tests of an oxygen sensor made of Yttria Stabilized Zirconia (YSZ) as a solid electrolyte. Several kinds of experiments were carried out to evaluate the electromotive force (emf) performance, stability and lifetime of the oxygen sensor with Ni/NiO, Cr/Cr 2 O 3 and Fe/FeO, respectively as a reference electrode. From the experimental data, it is suggested that the reference electrode of Ni/NiO reveals the most appropriate characteristic of the sensor to measure the partial oxygen pressure in a fuel rod. It is the final goal of this development to clarify the change of oxygen chemical potential in a fuel rod during power transient. (author)

  8. Three-dimensional simulations in optimal performance trial between two types of Hall sensors fabrication technologies

    Energy Technology Data Exchange (ETDEWEB)

    Paun, Maria-Alexandra, E-mail: map65@cam.ac.uk

    2015-10-01

    The main objective of the present work is to make a comparison between Hall devices integrated in regular bulk and Silicon-on-Insulator (SOI) CMOS technology. A three-dimensional model based on numerical estimation is provided for a particular XL Hall structure in two different technologies (the first one is XFAB XH 0.35 µm regular bulk CMOS and the second one is XFAB SOI XI10 1 µm non-fully depleted). In assessing the performance of the Hall Effect sensors included in the comparison, both three-dimensional physical simulations and measurements results will be used. In order to discriminate which category of sensors has the highest performance, their main characteristic parameters, including input resistance, Hall voltage, absolute sensitivity and their temperature drift, will be extracted and compared. Electrostatic potential and current density distribution are important aspects that are also investigated. The particular technology offering the highest sensor performance is identified. - Highlights: • A comparison between Hall devices integrated in regular bulk and SOI CMOS technologies is made. • A three-dimensional model for the XL Hall structure, in the two technologies, is provided. • The main characteristic parameters and the temperature drift are investigated. • The sensors performance is evaluated using 3D physical simulations and measurements data.

  9. Performance Testing of Homeland Security Technologies in U.S. EPA's Environmental Technology Verification (ETV) Program

    National Research Council Canada - National Science Library

    Kelly, Thomas J; Hofacre, Kent C; Derringer, Tricia L; Riggs, Karen B; Koglin, Eric N

    2004-01-01

    ... (reports and test plans available at www.epa.gov/etv). In the aftermath of the terrorist attacks of September 11, 2001, the ETV approach has also been employed in performance tests of technologies relevant to homeland security (HS...

  10. The performance characteristics of the Philips Gemini PET/CT scanner

    International Nuclear Information System (INIS)

    O'Keefe, G.J.; Papenfuss, A.T.; Scott, A.M.; Rowe, C.C.

    2002-01-01

    Full text: The Department of Nuclear Medicine, Centre for PET at the ARMC is commissioning a next generation PET/CT scanner based on gadolinium silicic dioxide (GSO) crystal technology to replace the BGO crystal PET scanner that has been in operation since 1992. The Gemini PET/CT scanner is a fully 3D PET system which offers significantly increased resolution and sensitivity allowing wholebody scans in under 30 minutes. Until the late 90's, PET scanners were largely used with septa for neurological imaging and the performance characteristics of PET scanners were presented according to the NEMA-NU2-94 standard which specifically addresses the performance of PET scanners for neurological applications. PET is now largely used without septa for oncological imaging and as such, the NEMA-NU2-94 standard does not adequately reflect performance. The NEMA-NU2-2001 standard was designed to incorporate the effects of out-of-FOV activity and its contribution to performance by virtue of the increased scatter and randoms that result when performing wholebody scans without the use of septa. As part of the acceptance program of the Allegro/Gemini systems, the NEMA-NU2-2001 standard will be used to characterise the spatial resolution, sensitivity, randoms and scatter contributions and the Noise Equivalent Count rate (NECr). These results will be presented and compared with the ECAT 951/31R performance characteristics. Copyright (2002) The Australian and New Zealand Society of Nuclear Medicine Inc

  11. Cogeneration technology alternatives study. Volume 2: Industrial process characteristics

    Science.gov (United States)

    1980-01-01

    Information and data for 26 industrial processes are presented. The following information is given for each process: (1) a description of the process including the annual energy consumption and product production and plant capacity; (2) the energy requirements of the process for each unit of production and the detailed data concerning electrical energy requirements and also hot water, steam, and direct fired thermal requirements; (3) anticipated trends affecting energy requirements with new process or production technologies; and (4) representative plant data including capacity and projected requirements through the year 2000.

  12. Characteristics of the Institute of Technology 'Prof. Jorge A. Sabato'

    International Nuclear Information System (INIS)

    Galvele, Jose R.

    2001-01-01

    A historical survey is made of the educational and training activities in metallurgy and material sciences carried out by the CNEA since 1962, that were the origin of the 'Prof. Jorge A. Sabato' Institute. Today the Institute, created by the CNEA in association with the National University of General San Martin, is preparing Engineers in Material Sciences and Masters and Ph. D. in Material Sciences and Technology (Mention in Physics and Material). The curricula of the studies are described in detail. The Information Center annexed to the Institute is also described

  13. Key Performance Characteristics of Organic Shrimp Aquaculture in Southwest Bangladesh

    Directory of Open Access Journals (Sweden)

    Christian Reinhard Vogl

    2012-05-01

    Full Text Available In Bangladesh, black tiger shrimp (Penaeus monodon; Fabricius, 1798 aquaculture has come to be one of the most important sectors in both the rural and national economies. Likewise, organic shrimp aquaculture has emerged as an alternative farming enterprise for farmers especially in the southwestern districts of Bangladesh. The present study aims to show key performance characteristics of organic shrimp farmers and farming in a prototypical shrimp farming area in Bangladesh. Data was collected in 2009 from organic shrimp farmers in the Kaligonj and Shyamnagar sub-districts through questionnaire interviews, transect walks and focus group discussions. The mean productivity of organic shrimp farming in the area is 320 kg ha−1 yr−1 (ranging from 120 to 711 kg ha−1year−1. Organic farmers are more likely to have a higher monthly income and less aquaculture experience. Moreover, suitable landholdings and classified labor distribution have been found to play an important role in the development of organic shrimp aquaculture. The most common assets of organic shrimp aquaculture are high yield, low production cost, available post larvae and high market prices. Small business farmers are likely to earn more income benefits from organic shrimp aquaculture than their larger-scale counterparts. Finally, the paper suggests that more research is needed to stimulate the success of organic shrimp aquaculture.

  14. Robotic Mobile System's Performance-Based MIMO-OFDM Technology

    Directory of Open Access Journals (Sweden)

    Omar Alani

    2009-10-01

    Full Text Available In this paper, a predistortion neural network (PDNN architecture has been imposed to the Sniffer Mobile Robot (SNFRbot that is based on spatial multiplexed wireless Orthogonal Frequency Division Multiplexing (OFDM transmission technology. This proposal is used to improve the system performance by combating one of the main drawbacks that is encountered by OFDM technology; Peak-to-Average Power Ratio (PAPR. Simulation results show that using PDNN resulted in better PAPR performance than the previously published work that is based on linear coding, such as Low Density Parity Check (LDPC codes and turbo encoding whether using flat fading channel or a Doppler spread channel.

  15. Dynamic Performance Characteristic Tests of Real Scale Lead Rubber Bearing for the Evaluation of Performance Criteria

    International Nuclear Information System (INIS)

    Kim, Min Kyu; Kim, Jung-Han; Choi, In-Kil

    2014-01-01

    Dynamic characteristic tests of full scale lead rubber bearing were performed for the evaluation of performance criteria of isolation system for nuclear power plants. For the dynamic test for a full scale rubber bearing, two 1500mm diameter lead rubber bearings were manufactured. The viewpoints of this dynamic test are determination of an ultimate shear strain level of lead rubber bearing, behavior of rubber bearing according to static and dynamic input motion, sinusoidal and random (earthquake) motion, and 1-dimentional and 2-dimensional input motion. In this study, seismic isolation device tests were performed for the evaluation of performance criteria of isolation system. Through this test, it can be recognized that in the case of considering a mechanical property test, dynamic and multi degree of loading conditions should be determined. But these differences should be examined how much affect to the global structural behavior

  16. Quantification of aggregate grain shape characteristics using 3-D laser scanning technology

    CSIR Research Space (South Africa)

    Mgangira, Martin B

    2013-07-01

    Full Text Available to identify the differences between individual aggregates. It was possible to quantify differences in particle shape characteristics at the small particle scale. The study has demonstrated the advantages of the innovative 3-D laser scanning technology...

  17. A study on performance characteristic: The effect of different parameter of renewable energy application

    Directory of Open Access Journals (Sweden)

    Tajudin Nadia

    2018-01-01

    Full Text Available Malaysia government still identify the best system in giving people solution on renewable energy. This study will focus on the performance of PV module. The characteristic of PV module still can be argued especially in absorbing the direct effect of sun light energy. The previous authors were not having a specific solution on the problem of the PV module implication after received the direct effect of sun light. This study will suggesting on the innovation of the process and system of PV module and restructuring the characteristic and provides information. The tools of quality PDCA and (OEE will be used to identify the best solution using the different type of cooling system. From this information, the stake holder can decrease the cost of using this type of technology.

  18. Guidance on the Technology Performance Level (TPL) Assessment Methodology

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Jochem [National Renewable Energy Lab. (NREL), Golden, CO (United States); Roberts, Jesse D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Babarit, Aurelien [Ecole Centrale de Nantes (France). Lab. of Research in Hydrodynamics, Energetics and Atmospheric Environment (LHEEA); Costello, Ronan [Wave Venture, Penstraze (United Kingdom); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neilson, Kim [Ramboll, Copenhagen (Denmark); Bittencourt, Claudio [DNV GL, London (United Kingdom); Kennedy, Ben [Wave Venture, Penstraze (United Kingdom); Malins, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dykes, Katherine [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-09-01

    This document presents the revised Technology Performance Level (TPL) assessment methodology. There are three parts to this revised methodology 1) the Stakeholder Needs and Assessment Guidance (this document), 2) the Technical Submission form, 3) the TPL scoring spreadsheet. The TPL assessment is designed to give a technology neutral or agnostic assessment of any wave energy converter technology. The focus of the TPL is on the performance of the technology in meeting the customer’s needs. The original TPL is described in [1, 2] and those references also detail the critical differences in the nature of the TPL when compared to the more widely used technology readiness level (TRL). (Wave energy TRL is described in [3]). The revised TPL is particularly intended to be useful to investors and also to assist technology developers to conduct comprehensive assessments in a way that is meaningful and attractive to investors. The revised TPL assessment methodology has been derived through a structured Systems Engineering approach. This was a formal process which involved analyzing customer and stakeholder needs through the discipline of Systems Engineering. The results of the process confirmed the high level of completeness of the original methodology presented in [1] (as used in the Wave Energy Prize judging) and now add a significantly increased level of detail in the assessment and an improved more investment focused structure. The revised TPL also incorporates the feedback of the Wave Energy Prize judges.

  19. Effect of technological advances on cochlear implant performance in adults.

    Science.gov (United States)

    Lenarz, Minoo; Joseph, Gert; Sönmez, Hasibe; Büchner, Andreas; Lenarz, Thomas

    2011-12-01

    To evaluate the effect of technological advances in the past 20 years on the hearing performance of a large cohort of adult cochlear implant (CI) patients. Individual, retrospective, cohort study. According to technological developments in electrode design and speech-processing strategies, we defined five virtual intervals on the time scale between 1984 and 2008. A cohort of 1,005 postlingually deafened adults was selected for this study, and their hearing performance with a CI was evaluated retrospectively according to these five technological intervals. The test battery was composed of four standard German speech tests: Freiburger monosyllabic test, speech tracking test, Hochmair-Schulz-Moser (HSM) sentence test in quiet, and HSM sentence test in 10 dB noise. The direct comparison of the speech perception in postlingually deafened adults, who were implanted during different technological periods, reveals an obvious improvement in the speech perception in patients who benefited from the recent electrode designs and speech-processing strategies. The major influence of technological advances on CI performance seems to be on speech perception in noise. Better speech perception in noisy surroundings is strong proof for demonstrating the success rate of new electrode designs and speech-processing strategies. Standard (internationally comparable) speech tests in noise should become an obligatory part of the postoperative test battery for adult CI patients. Copyright © 2011 The American Laryngological, Rhinological, and Otological Society, Inc.

  20. Advanced fuel technology and performance: Current status and trends

    International Nuclear Information System (INIS)

    1990-11-01

    During the last years the Nuclear Fuel Cycle and Waste Management Division of the IAEA has been giving great attention to the collection, analysis and exchange of information in the field of reactor fuel technology. Most of these activities are being conducted in the framework of the International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT). The purpose of this Advisory Group Meeting on Advanced Fuel Technology and Performance was to update and to continue the previous work, and to review the experience of advanced fuel technology, its performance with regard to all types of reactors and to outline the future trends on the basis of national experience and discussions during the meeting. As a result of the meeting a Summary Report was prepared which reflected the status of the advanced nuclear fuel technology up to 1990. The 10 papers presented by participants of this meeting are also published here. A separate abstract was prepared for each of these papers. Refs, figs and tabs

  1. Enabling Detailed Energy Analyses via the Technology Performance Exchange: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Studer, D.; Fleming, K.; Lee, E.; Livingood, W.

    2014-08-01

    One of the key tenets to increasing adoption of energy efficiency solutions in the built environment is improving confidence in energy performance. Current industry practices make extensive use of predictive modeling, often via the use of sophisticated hourly or sub-hourly energy simulation programs, to account for site-specific parameters (e.g., climate zone, hours of operation, and space type) and arrive at a performance estimate. While such methods are highly precise, they invariably provide less than ideal accuracy due to a lack of high-quality, foundational energy performance input data. The Technology Performance Exchange was constructed to allow the transparent sharing of foundational, product-specific energy performance data, and leverages significant, external engineering efforts and a modular architecture to efficiently identify and codify the minimum information necessary to accurately predict product energy performance. This strongly-typed database resource represents a novel solution to a difficult and established problem. One of the most exciting benefits is the way in which the Technology Performance Exchange's application programming interface has been leveraged to integrate contributed foundational data into the Building Component Library. Via a series of scripts, data is automatically translated and parsed into the Building Component Library in a format that is immediately usable to the energy modeling community. This paper (1) presents a high-level overview of the project drivers and the structure of the Technology Performance Exchange; (2) offers a detailed examination of how technologies are incorporated and translated into powerful energy modeling code snippets; and (3) examines several benefits of this robust workflow.

  2. On Cultivation of Characteristic Talents in Law in Institutes of Technology

    Science.gov (United States)

    Li, Hong

    2011-01-01

    For the time being, professional education of law offered by institutes of technology has become an important component of cultivation of professional talents in law in China. Only if institutes of technology face up with their disadvantages, make full use of their resource advantages and cultivate characteristic talents in law, are they able to…

  3. An analysis of CDTN performance in the reactors technology area

    International Nuclear Information System (INIS)

    Pinheiro, R.B.

    1985-01-01

    The author makes an analysis of CDTN (Centro de Desenvolvimento da Tecnologia Nuclear) performance in the reactors technology area, showing difficulties and failures, but emphasizing the particular competence and capacity acquired in this area, as for example: the capacity in codes and methods are of neutronic calculations and nuclear projects, experimental thermohydraulic program, tests services in components and the others. (C.M.) [pt

  4. Synthesizing Soft Systems Methodology and Human Performance Technology

    Science.gov (United States)

    Scott, Glen; Winiecki, Donald J.

    2012-01-01

    Human performance technology (HPT), like other concepts, models, and frameworks that we use to describe the world in which we live and the way we organize ourselves to accomplish valuable activities, is built from paradigms that were fresh and relevant at the time it was conceived and from the fields of study from which it grew. However, when the…

  5. A Cross-Cultural Investigation of Human Performance Technology Interventions

    Science.gov (United States)

    Vadivelu, Ramaswamy N.

    2010-01-01

    Human Performance Technology (HPT) is a field of practice that has evolved from advancements in organizational development, instructional design, strategic human resource management and cognitive psychology. As globalization and trends like outsourcing and off-shoring start to dominate the way organizations grow, HPT practitioners are managing the…

  6. Motivating students to perform an experiment in technological design contexts

    NARCIS (Netherlands)

    Logman, P.S.W.M.; Kaper, W.H.; Ellermeijer, A.L.; Lindell, A.; Kähkönen, A.-L.; Viiri, J.

    2012-01-01

    In a teaching-learning sequence on the subject of energy we have tried technological design contexts to motivate students by using only context-based reasons to perform experiments on the subject of energy. We use these experiments to have the students reinvent practical laws of energy conservation

  7. Performance of Improved Dairy Cattle Technologies Among Farmers ...

    African Journals Online (AJOL)

    User

    This study evaluated the performance of different dairy cattle technologies ... common phenomenon in Nigeria, especially among the poor segment of the society ... considerable amounts (over 70%) of milk today (Olaloku and Debre, 1992). ..... cross-bred dairy cattle was reported to be 30 percent of total dairy animals in.

  8. Technology for analysis of sodium pool fire characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byung Ho; Jeong, K C; Jeong, J Y; Kim, T J; Choi, J H; Choi, Y D; Hwang, S T

    2000-09-01

    Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m{sup 3} (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure.

  9. Technology for analysis of sodium pool fire characteristics

    International Nuclear Information System (INIS)

    Kim, Byung Ho; Jeong, K. C.; Jeong, J. Y.; Kim, T. J.; Choi, J. H.; Choi, Y. D.; Hwang, S. T.

    2000-09-01

    Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m 3 (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure

  10. Technology for analysis of sodium pool fire characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byung Ho; Jeong, K. C.; Jeong, J. Y.; Kim, T. J.; Choi, J. H.; Choi, Y. D.; Hwang, S. T

    2000-09-01

    Basic and detail design for medium sodium fire test facility was carried out and medium sodium fire test facility was constructed. Design data is as follows. - Test cell material : Concrete with high strength - Test cell dimension ; 48m{sup 3} (3x4x4m) - Design temp. ; 700 deg C - Operation temp. ; 530 deg C - Design pressure ; 1 bar (max.) - Dimension(Inside) : 3 x 4 x 4(m) - Test cell thickness ; 45cm - Liner plate with (Thickness : 3mm) In this study, sodium fire characteristics was analyzed and data for validation of computer code was produced. Oxygen and sodium filled in pool pan didn't burns instantly, but pool fire occurred through pre-ignition. Distribution of temperature in test cell was divided by two parts, and temperature at upper position appeared to be higher than temperature at lower position. The temperature in test cell increased with the feed of sodium. The pressure in test cell increased with the feed of sodium. When the feed of sodium was 8kg, peak pressure was 0.075 bar. Peak temperature in sodium pool appeared to be 854 deg C regardless of the feed of sodium. Decrease of 1% in oxygen concentration showed the rise of 0.036bar in pressure.

  11. The influence of system quality characteristics on health care providers’ performance: Empirical evidence from Malaysia

    Directory of Open Access Journals (Sweden)

    Mohd Idzwan Mohd Salleh

    2016-11-01

    Full Text Available Summary: Background: The Ministry of Health Malaysia initiated the total hospital information system (THIS as the first national electronic health record system for use in selected public hospitals across the country. Since its implementation 15 years ago, there has been the critical requirement for a systematic evaluation to assess its effectiveness in coping with the current system, task complexity, and rapid technological changes. The study aims to assess system quality factors to predict the performance of electronic health in a single public hospital in Malaysia. Methods: Non-probability sampling was employed for data collection among selected providers in a single hospital for two months. Data cleaning and bias checking were performed before final analysis in partial least squares-structural equation modeling. Results and conclusions: Convergent and discriminant validity assessments were satisfied the required criterions in the reflective measurement model. The structural model output revealed that the proposed adequate infrastructure, system interoperability, security control, and system compatibility were the significant predictors, where system compatibility became the most critical characteristic to influence an individual health care provider’s performance. The previous DeLone and McLean information system success models should be extended to incorporate these technological factors in the medical system research domain to examine the effectiveness of modern electronic health record systems. In this study, care providers’ performance was expected when the system usage fits with patients’ needs that eventually increased their productivity. Keywords: Electronic health records system, System quality characteristics, Care providers’ performance, Evaluation, Partial least squares-structural equation modeling

  12. The influence of system quality characteristics on health care providers' performance: Empirical evidence from Malaysia.

    Science.gov (United States)

    Mohd Salleh, Mohd Idzwan; Zakaria, Nasriah; Abdullah, Rosni

    The Ministry of Health Malaysia initiated the total hospital information system (THIS) as the first national electronic health record system for use in selected public hospitals across the country. Since its implementation 15 years ago, there has been the critical requirement for a systematic evaluation to assess its effectiveness in coping with the current system, task complexity, and rapid technological changes. The study aims to assess system quality factors to predict the performance of electronic health in a single public hospital in Malaysia. Non-probability sampling was employed for data collection among selected providers in a single hospital for two months. Data cleaning and bias checking were performed before final analysis in partial least squares-structural equation modeling. Convergent and discriminant validity assessments were satisfied the required criterions in the reflective measurement model. The structural model output revealed that the proposed adequate infrastructure, system interoperability, security control, and system compatibility were the significant predictors, where system compatibility became the most critical characteristic to influence an individual health care provider's performance. The previous DeLone and McLean information system success models should be extended to incorporate these technological factors in the medical system research domain to examine the effectiveness of modern electronic health record systems. In this study, care providers' performance was expected when the system usage fits with patients' needs that eventually increased their productivity. Copyright © 2016 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

  13. Shifting technology from the universities to a high performance business

    Directory of Open Access Journals (Sweden)

    Lazarus Neely

    2009-12-01

    Full Text Available The first aim of this study is to identify the external and internal factors that have shaped the performance of Technology-Based Start-up Firms (TBSF in the US. The second goal is to compare this study with a previous study conducted in Brazil, to identify incubator best practices that may increase the performance of incubated firms. The US study focuses on graduated firms from the Indiana University incubator located in Indianapolis. The main partners of three technology-based start-up firms were interviewed, based on a semi-structured questionnaire. The outcomes from our analysis indicated that the TBSF have both internal and external factors that affect their performance. The analysis showed that as an external factor, the incubator’s connection with university was helpful for obtaining capital. As internal factors, the technical expertise and entrepreneur managerial competence was identified as fundamental factors for TBSF success. The analysis also indicated that some of those factors are different between Brazilian firms and American firms. In Brazil, the management training offered by the incubator is considered very important for the performance of the incubated firms. This was not confirmed in the American study. Knowing what affects the performance of technology-based start-up firms will help incubators offer improved, and more comprehensive services enabling firms to develop and expand.

  14. Drivers of international performance of Brazilian technology-based firms

    Directory of Open Access Journals (Sweden)

    Maria Carolina Serpa Fagundes de Oliveira

    2018-01-01

    Full Text Available For Technology-Based Firms, international expansion represents an opportunity for growth and value creation. The present study was designed to analyze the role of technology-based companies (TBCs internationalization drivers on international performance. Therefore, a descriptive research was carried out with a quantitative approach performed through a survey. Data collection happened with 53 Brazilian TBCs located in innovation habitats. These data were analyzed by multivariate statistical technique. The results showed that the determinants of the international performance of Brazilian TBCs, can be set by external influencers (localization in innovation habitats, integration into global productive chains, partnerships and strategic alliances for innovation and government policies and internal influencers (innovation capability, international market orientation and international marketing skills.

  15. Cracking and impact performance characteristics of plastic composite ties.

    Science.gov (United States)

    2012-03-01

    As followup to a workshop on Engineered Composite Ties sponsored by the American Railway Engineering and Maintenance-of-Way Association and the Federal Railroad Administration, the Transportation Technology Center, Inc., in Pueblo, CO, conducted a se...

  16. Converging Technologies for Improving Human Performance: Integrating From the Nanoscale

    International Nuclear Information System (INIS)

    Roco, M.C.; Bainbridge, W.S.

    2002-01-01

    In the early decades of the twenty-first century, concentrated efforts can unify science based on the unity of nature, thereby advancing the combination of nanotechnology, biotechnology, information technology, and new humane technologies based in cognitive science. Converging technologies integrated from the nanoscale could determine a tremendous improvement in human abilities and societal outcomes. This is a broad, cross cutting, emerging, and timely opportunity of interest to individuals, society, and humanity in the long term.About eighty scientific leaders, industry experts, and policy makers across a range of fields have contributed to develop a vision for the potential to improve human physical, mental, and social capabilities through the convergence of the four technologies. Six major themes have emerged: (a) The broad potential of converging technologies; (b) Expanding human cognition and communication; (c) Improving human health and physical capabilities; (d) Enhancing group and societal outcomes; (e) National security, and (f) Unifying science and education. This article summarizes the observations, conclusions, and recommendations made in the report (Roco and Bainbridge, eds., 2002. Converging Technologies for Improving Human Performance, NSF-DOC Report, June 2002, Arlington VA, USA)

  17. High-performance silicon photonics technology for telecommunications applications.

    Science.gov (United States)

    Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Ishikawa, Yasuhiko; Wada, Kazumi; Yamamoto, Tsuyoshi

    2014-04-01

    By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge-based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge-based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications.

  18. High-performance silicon photonics technology for telecommunications applications

    International Nuclear Information System (INIS)

    Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Yamamoto, Tsuyoshi; Ishikawa, Yasuhiko; Wada, Kazumi

    2014-01-01

    By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge–based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge–based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications. (review)

  19. High-performance silicon photonics technology for telecommunications applications

    Science.gov (United States)

    Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Ishikawa, Yasuhiko; Wada, Kazumi; Yamamoto, Tsuyoshi

    2014-04-01

    By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge-based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge-based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications.

  20. Development of Nano technology in High Performance Concrete

    International Nuclear Information System (INIS)

    Nima Farzadnia; Abang Abdullah Abang Ali; Ramazan Demirboga; Demirboga, R.

    2011-01-01

    Concrete is the most widely used building material all around the world which has been undergoing many changes aligned with technological advancement. The most recent available type of concrete is high performance concrete which is produced by employing different admixtures both chemical and mineral to enhance mechanical properties and durability. Recently, technology has made it easy for scientist to study nano sized admixtures and their effect on microstructure of concrete. This paper reviews nano particles in cement composites and how they can improve different properties of concrete. (author)

  1. Performance Management Practices, Information and Communication Technology (ICT) Adoption and Managed Performance

    Science.gov (United States)

    Kagaari, James R. K.; Munene, John C.; Ntayi, Joseph Mpeera

    2010-01-01

    Purpose: The purpose of this paper is to demonstrate the need for managers of public universities to pay attention to performance management practices and information communication technology (ICT) adoption in order to achieve successful managed performance. Design/methodology/approach: Using a disproportionate stratified purposive approach, a…

  2. Can Knowledge of the Characteristics of "High Performers" Be Generalised?

    Science.gov (United States)

    McKenna, Stephen

    2002-01-01

    Two managers described as high performing constructed complexity maps of their organization/world. The maps suggested that high performance is socially constructed and negotiated in specific contexts and management competencies associated with it are context specific. Development of high performers thus requires personalized coaching more than…

  3. A framework of performance criteria defining sustainable construction technologies

    International Nuclear Information System (INIS)

    Sturges, W.G.

    1992-01-01

    As our global culture encounters accelerating rates of resource depletion, environmental degradation, and societal inequality, it increasingly needs tools to rate building systems by environmental and socioeconomic criteria. By investigating light frame structural systems based on principles of ecological design, it is possible to not only identify the structures' potential impacts on the health of their site and larger community, but also to establish a framework of performance criteria for comparatively evaluating a variety of construction technologies. This paper summarizes the development and application of such a framework, based upon the ecosystems and culture of the Pacific Northwest's Cascadia Bioregion. The framework has been comparatively applied to solid-sawn lumber, trusses, and composite wood I-joists. These three framing technologies together represent traditional, contemporary, and progressive structural systems. Their individual and collective performance, based upon the application of the hypothesized criteria, offer insights into what might be a more ideal framing system of the sustainable future

  4. Exploring Advanced Technology Gas Turbine Engine Design and Performance for the Large Civil Tiltrotor (LCTR)

    Science.gov (United States)

    Snyder, Christopher A.

    2014-01-01

    A Large Civil Tiltrotor (LCTR) conceptual design was developed as part of the NASA Heavy Lift Rotorcraft Systems Investigation in order to establish a consistent basis for evaluating the benefits of advanced technology for large tiltrotors. The concept has since evolved into the second-generation LCTR2, designed to carry 90 passengers for 1,000 nautical miles at 300 knots, with vertical takeoff and landing capability. This paper explores gas turbine component performance and cycle parameters to quantify performance gains possible for additional improvements in component and material performance beyond those identified in previous LCTR2 propulsion studies and to identify additional research areas. The vehicle-level characteristics from this advanced technology generation 2 propulsion architecture will help set performance levels as additional propulsion and power systems are conceived to meet ever-increasing requirements for mobility and comfort, while reducing energy use, cost, noise and emissions. The Large Civil Tiltrotor vehicle and mission will be discussed as a starting point for this effort. A few, relevant engine and component technology studies, including previous LCTR2 engine study results will be summarized to help orient the reader on gas turbine engine architecture, performance and limitations. Study assumptions and methodology used to explore engine design and performance, as well as assess vehicle sizing and mission performance will then be discussed. Individual performance for present and advanced engines, as well as engine performance effects on overall vehicle size and mission fuel usage, will be given. All results will be summarized to facilitate understanding the importance and interaction of various component and system performance on overall vehicle characteristics.

  5. Rail gun performance and plasma characteristics due to wall ablation

    Science.gov (United States)

    Ray, P. K.

    1986-01-01

    The experiment of Bauer, et al. (1982) is analyzed by considering wall ablation and viscous drag in the plasma. Plasma characteristics are evaluated through a simple fluid-mechanical analysis considering only wall ablation. By equating the energy dissipated in the plasma with the radiation heat loss, the average properties of the plasma are determined as a function of time.

  6. Growth performance and carcass characteristics of three Ethiopian ...

    African Journals Online (AJOL)

    Breed affected the weights of internal fat depots. The findings indicate that breed affected the carcass characteristics of the three Ethiopian goat breeds. Keywords: Indigenous goats; carcass yield; carcass composition; primal cuts; non-carcass components. South African Journal of Animal Science Vol. 37 (4) 2007: pp.221- ...

  7. Hearing Instrument using receivers with different performance characteristics

    DEFF Research Database (Denmark)

    2009-01-01

    The invention regards a signal processing device in a hearing aid, wherein the signal processing device is electrically coupled to a connection socket operable to detachably connect a receiver to the socket and whereby the signal processing device further comprise a detector operable to detect...... a characteristics of the receiver which is connected to the signal processing device through the connection socket....

  8. Design and performance characteristics of a krypton chloride (λ ...

    Indian Academy of Sciences (India)

    2014-01-07

    Jan 7, 2014 ... Development of a discharge-pumped krypton chloride (KrCl) laser operating at 222 nm wavelength is demonstrated. In this paper the design, successful realization and operating characteristics of KrCl excimer laser are reported. The laser is driven by a simple and efficient excitation technique using ...

  9. Performance of sampling methods to estimate log characteristics for wildlife.

    Science.gov (United States)

    Lisa J. Bate; Torolf R. Torgersen; Michael J. Wisdom; Edward O. Garton

    2004-01-01

    Accurate estimation of the characteristics of log resources, or coarse woody debris (CWD), is critical to effective management of wildlife and other forest resources. Despite the importance of logs as wildlife habitat, methods for sampling logs have traditionally focused on silvicultural and fire applications. These applications have emphasized estimates of log volume...

  10. performance characteristics of an armature voltage controlled dc motor

    African Journals Online (AJOL)

    Dr Obe

    obtained by digital computer analysis. The results show that closed loop operation, with appropriate control ... Using digital computer analysis, the driver characteristics of a test motor is investigated. In the closed loop ... system circuit failure especially with respect to the semiconductor devices that may be used in varying ...

  11. Benchmarking and performance improvement at Rocky Flats Technology Site

    International Nuclear Information System (INIS)

    Elliott, C.; Doyle, G.; Featherman, W.L.

    1997-03-01

    The Rocky Flats Environmental Technology Site has initiated a major work process improvement campaign using the tools of formalized benchmarking and streamlining. This paper provides insights into some of the process improvement activities performed at Rocky Flats from November 1995 through December 1996. It reviews the background, motivation, methodology, results, and lessons learned from this ongoing effort. The paper also presents important gains realized through process analysis and improvement including significant cost savings, productivity improvements, and an enhanced understanding of site work processes

  12. Editorial: Technology for higher education, adult learning and human performance

    OpenAIRE

    Minhong Wang; Chi-Cheng Chang; Feng Wu

    2013-01-01

    This special issue is dedicated to technology-enabled approaches for improving higher education, adult learning, and human performance. Improvement of learning and human development for sustainable development has been recognized as a key strategy for individuals, institutions, and organizations to strengthen their competitive advantages. It becomes crucial to help adult learners and knowledge workers to improve their self-directed and life-long learning capabilities. Meanwhile, advances in t...

  13. PERFORMANCE MANAGEMENT APPROACHES IN ECONOMIC ORGANIZATIONS USING INFORMATION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Anca Mehedintu

    2012-03-01

    Full Text Available Performance management includes activities that ensure that goals are consistently being met inan effective and efficient manner. Performance management can focus on the performance of an organization, adepartment, employee, or even the processes to build a product or service, as well as many other areas.In these days of globalization and intensive use of information technology, the organizations must defineand implement an appropriate strategy that would support their medium-term development, stability andcompetitiveness. This is achieved through a coherent and interrelated set of activities for understanding thecustomer expectations and the level at which the offer of organization add value to customers and satisfy theirneeds, define their internal organization to allow timely response to market demands without losing focus on client,tracking strategy and business model for the accomplishment of the organization mission, aligning the existing ITproject management or under development implementation in organization with the strategic management oforganization etc. Strategic Management determines the improvement of processes, effective use of resources, focuson critical areas in terms of finance, creating opportunities for innovation and technological progress, improvementof the supply mechanism and the duty to promote personal interaction and negotiation at all levels, continuousassessment of organization and its technological trends, analyze the market potential and competence field etc.Strategic management system will not give good results if the strategy is not defined by a set of operationalobjectives clearly at all levels.Business performance is based on a set of analytical processes of business, supported by informationtechnology that defines the strategic goals that can be measured by performance indicators. EnterprisePerformance Management creates a powerful and precise environment, characterized by data consistency,efficiency analysis

  14. Development of structural technology for a high performance spacer grid

    International Nuclear Information System (INIS)

    Song, Kee Nam; Kim, H. K.; Kang, H. S.

    2003-03-01

    A spacer grid in a LWR fuel assembly is a key structural component to support fuel rods and to enhance the heat transfer from the fuel rod to the coolant. In this research, the main research items are the development of inherent and high performance spacer grid shapes, the establishment of mechanical/structural analysis and test technology, and the set-up of basic test facilities for the spacer grid. The main research areas and results are as follows. 1. 14 different spacer grid candidates have been invented and applied for domestic and US patents. Among the candidates six are chosen from the patent. 2. Two kinds of spacer grids are finally selected for the advanced LWR fuel after detailed performance tests on the candidates and commercial spacer grids from a mechanical/structural point of view. According to the test results the features of the selected spacer grids are better than those of the commercial spacer grids. 3. Four kinds of basic test facilities are set up and the relevant test technologies are established. 4. Mechanical/structural analysis models and technology for spacer grid performance are developed and the analysis results are compared with the test results to enhance the reliability of the models

  15. REFERENCED TECHNOLOGICAL PERFORMANCES FOR STURGEON FINGERLING BREEDING IN INTENSIVE SYSTEM

    Directory of Open Access Journals (Sweden)

    MARILENA TALPES

    2008-10-01

    Full Text Available Work objective is to present an oversight regarding the modality to rearing the descendents of anadromous sturgeon species, Acipenser stellatus, Acipenser gueldenstaedti and Huso huso, obtained trough artificial reproduction, indicating successively, the production system, its management, alimentation strategy for sturgeon species and technological performances registered by these. Experiments developed during two phases, respectively the post-embryonary one and sapling rearing during of a 168 days period. Registered performances of sturgeon species material were assessed in conformity with specifically biotechnological indicators.

  16. The impact of technology on sporting performance in Olympic sports.

    Science.gov (United States)

    Haake, Steve J

    2009-11-01

    To assess the effect of technology on sport, the performance statistics for four disciplines were analysed: the 100-m sprint, pole vault, javelin, and cycling. The concept of a performance improvement index was developed to allow comparison between athletes and between sports with a higher index indicating a greater improvement in the sport. The following performance improvement indices were found: 100-m sprint, 24% over 108 years; pole vault, 86% over 94 years; javelin, 95% over 76 years; 4-km individual pursuit, 35% over 32 years; one-hour cycling record, 221% over 111 years. Around 4% of the index for the sprint was attributed to tighter, aerodynamic clothing, suggesting that general athletic improvement in sprint-type events has been around 20%. Technological developments in simple equipment such as the pole vault or javelin were seen to affect the index by around 30%, while the index associated with aerodynamic improvements in the one-hour record was around 100%. It is concluded that the performance improvement index could be extended to amateur as well as elite sport where distance or time is used as a measure of performance.

  17. Class modality, student characteristics, and performance in a community college introductory STEM course

    Science.gov (United States)

    Fogle, Thomas Ty

    Research on introductory STEM course performance has indicated that student characteristics (age, ethnicity and gender) and Grade Point Average (G.P.A.) can be predictive of student performance, and by implication, a correlation among these factors can help determine course design interventions to help certain types of students perform well in introductory STEM courses. The basis of this study was a community college Visual Basic programming course taught in both online and hybrid format. Beginning students in this course represented a diverse population residing in a large, mid-western, city and surrounding communities. Many of these students were defined as "at-Risk" or "non-traditional, which generally means any combination of socio-economic, cultural, family and employment factors that indicate a student is non-traditional. Research has shown these students struggle academically in technologically dense STEM courses, and may require student services and support to achieve their individual performance goals. The overall number in the study range was 392 distance students and 287 blended course students. The main question of this research was to determine to what extent student characteristics in a community college context, and previous success, as measured in overall G.P.A., were related to course performance in an introductory Visual Basic programming (STEM) course; and, whether or not a combination of these factors and course modality was predictive of success. The study employed a quantitative, quasi-experimental design to assess whether students' course performance was linked to course modality, student characteristics and overall G.P.A. The results indicated that the only predictor of student performance was overall G.P.A. Despite the research analyzed in Chapter 2, there was no statistically significant relationship to modality, age, ethnicity, or gender to performance in the course. Cognitive load is significant in a computer programming course and it

  18. MANAGEMENT TEAM CHARACTERISTICS: EVIDENCE FROM UNIVERSITY GOVERNANCE AND SCHOOL PERFORMANCE

    OpenAIRE

    Hsiang-Tsai Chiang; Mei-Chih Lin

    2013-01-01

    The paper examines cognition from the viewpoint of internal management teams of private universities against satisfaction with school performance, applying the SEM model. Empirical results show that the board’s operational effectiveness and attendance rate for internal important meetings held on campus have a significantly positive relationship with implementing effectiveness and satisfaction with school administrative performance. The satisfaction with school administrative performance and...

  19. Common Characteristics of Good and Poorly Performing AC Pavements

    Science.gov (United States)

    1999-12-01

    This report documents the analysis and findings of a study to identify the site conditions and design/construction features of : flexible pavements that lead to good performance and those that lead to poor performance. Data from the Long Term Pavemen...

  20. Common Characteristics of Good and Poorly Performing PCC Pavements

    Science.gov (United States)

    1998-01-01

    This report documents the analysis and findings of a study to identify the site conditions and design/construction features of concrete pavements (JPCP, JRCP, CRCP) that lead to good performance and those that lead to poor performance. Data from Long...

  1. Variability of Performance: A "Signature" Characteristic of Learning Disabled Children?

    Science.gov (United States)

    Fuchs, Douglas; And Others

    Two studies were conducted to compare the performance instability of children (grades 3-9) labeled learning disabled/brain injured (LD/BI) to the performance instability of emotionally handicapped (EH) children. In the first study, 50 LD/BI and 37 EH students were measured on three third grade reading passages twice, once within one sitting and…

  2. Poor physician performance in the Netherlands: characteristics, causes, and prevalence.

    NARCIS (Netherlands)

    Goor, M.M.P.G. van den; Wagner, C.; Lombarts, K.M.J.M.H.

    2015-01-01

    Introduction: Poor physician performance has a profound impact on patient safety and society's trust in the health care system. The attention that this topic has received in the media suggests that it is a large-scale issue. However, research about physician performance is still scant; there is

  3. Technological Characteristics of the Longissimus Dorsi Muscle of Pig Depending on the Genetic Type

    OpenAIRE

    Consuela Roibu; Ionuţ Beia; Mariana Bran; Elena Popescu-Micloşanu; Răzvan Popa

    2012-01-01

    The processes of technological processing of meat carried out in optimal conditions, require a good knowledge of the water capacity of bearings by the raw material that makes the manufacturing processes of the various preparations. Technological characteristics of pigmeat analyzed in this paper are represented by water retention ability, capacity of hydration and the degree of perselation. The researches have been conducted on 40 samples, taken from the muscle of the longissimus dorsi from br...

  4. Risk and Performance Technologies: Identifying the Keys to Successful Implementation

    International Nuclear Information System (INIS)

    McClain, Lynn; Smith, Art; O'Regan, Patrick

    2002-01-01

    The nuclear power industry has been utilizing risk and performance based technologies for over thirty years. Applications of these technologies have included risk assessment (e.g. Individual Plant Examinations), burden reduction (e.g. Risk-Informed Inservice Inspection, RI-ISI) and risk management (Maintenance Rule, 10CFR50.65). Over the last five to ten years the number of risk-informed (RI) burden reduction initiatives has increased. Unfortunately, the efficiencies of some of these applications have been questionable. This paper investigates those attributes necessary to support successful, cost-effective RI-applications. The premise to this paper is that by understanding the key attributes that support one successful application, insights can be gleaned that will streamline/coordinate future RI-applications. This paper is an extension to a paper presented at the Pressure Vessel and Piping (PVP-2001) Conference. In that paper, a number issues and opportunities were identified that needed to be assessed in order to support future (and efficient) RI-applications. It was noted in the paper that a proper understanding and resolution of these issues will facilitate implementation of risk and performance technology in the operation, maintenance and design disciplines. In addition, it will provide the foundation necessary to support regulatory review and approval. (authors)

  5. Characteristics and performance of anaerobic wastewater treatment (a review)

    International Nuclear Information System (INIS)

    Zeb, B.S.; Mahmood, Q.; Pervez, A.

    2013-01-01

    Summary: Pakistan's current population of 180 million is expected to grow to about 221 million by the year 2025. In developing countries such as Pakistan water pollution is a major threat to the livelihood of people. Pakistan is also currently experiencing profound demographic, economic changes and energy crisis that have major implications for water management. The contamination of aquatic and terrestrial ecosystems with heavy metals is a major environmental problem. Each pollution problem calls for specific optimal and cost effective solution so if one technology proves less or ineffective other takes its place. Every day the vast amounts of the municipal, industrial and agricultural wastes are released in to the environment and create serious problems. Anaerobic digestion is very attractive and cost-effective option and technology for the highly loaded waste water treatment and energy conversion. The anaerobic process is in many ways ideal for waste treatment. It has several significant advantages over other available methods. In this process organic matter is utilized as source of electron donor to reduce carbon dioxide to produce methane gas. It involves three bacterial groups namely: hydrolytic, acetogenic and methanogenic bacteria that work optimally at pH and temperature ranges of 6.8 to 7.5 and 30-35 degree C, respectively. The residence time in a digester varies with the amount and type of feed material, the configuration of the digestion system, and whether it be one-stage or two-stage. It is ideal for all kinds of wastewaters. Currently anaerobic technology is being operated at full scale in many industrialized nations. (author)

  6. Performance ratio hardness characteristics polystyrene-metal composite materials

    International Nuclear Information System (INIS)

    Klepikov, V.F.; Prokhorenko, E.M.; Lytvynenko, V.V.; Zakharchenko, A.A.; Hazhmuradov, M.A.

    2015-01-01

    The methods of measuring the hardness of layered polystyrene-metallic composite materials. It is proposed to use powder-like tungsten and powder-like steel as radiation-protective layer. A measurement of the hardness of composites of different composition, and given its dependence on the particle size and their form. The possibility of increasing the hardness of the composites reinforced with metallic additives. Radiation-protective characteristics were calculated for the studied species of composite materials. Influence of the quantitative composition of the metal components is studied on the change of the absorbed dose of gamma radiation

  7. the steady-state performance characteristics of single phase transfer

    African Journals Online (AJOL)

    2012-11-03

    Nov 3, 2012 ... field (SPTF) machine operating in the asynchronous mode from which the performance charac- teristics could be ... motor from a poly-phase induction motor by discon- necting one of its .... tating magnetic field. The pulsating ...

  8. Technology Evaluation Report 17. Videoconferencing in Theatre and Performance Studies

    Directory of Open Access Journals (Sweden)

    Mark Childs

    2003-04-01

    Full Text Available Previous reports in this series have indicated the growing acceptance of video-conferencing in education delivery. The current report compares a series of video-conferencing methods in an activity requiring precision of expression and communication: theatre and performance studies. The Accessing and Networking with National and International Expertise (ANNIE project is a two-year project undertaken jointly by the University of Warwick and the University of Kent at Canterbury, running from March 2001 to March 2003. The project's aim is to enhance students' learning experience in theatre studies by enabling access to research-based teaching and to workshops led by practitioners of national and international standing. Various technologies have been used, particularly ISDN video-conferencing, computer-mediated conferencing, and the Internet. This report concludes that video-conferencing methods will gain acceptance in education, as academic schools themselves are able to operate commonly available technology the assistance of specialised service units.

  9. Oil Bypass Filter Technology Performance Evaluation - January 2003 Quarterly Report

    Energy Technology Data Exchange (ETDEWEB)

    Laurence R. Zirker; James E. Francfort

    2003-01-01

    This report details the initial activities to evaluate the performance of the oil bypass filter technology being tested by the Idaho National Engineering and Environmental Laboratory (INEEL) for the U.S. Department of Energy's FreedomCAR & Vehicle Technologies Program. Eight full-size, four-cycle diesel-engine buses used to transport INEEL employees on various routes have been equipped with oil bypass systems from the puraDYN Corporation. Each bus averages about 60,000 miles a year. The evaluation includes an oil analysis regime to monitor the presence of necessary additives in the oil and to detect undesirable contaminants. Very preliminary economic analysis suggests that the oil bypass system can reduce life-cycle costs. As the evaluation continues and oil avoidance costs are quantified, it is estimated that the bypass system economics may prove increasingly favorable, given the anticipated savings in operational costs and in reduced use of oil and waste oil avoidance.

  10. Oil Bypass Filter Technology Performance Evaluation - First Quarterly Report

    Energy Technology Data Exchange (ETDEWEB)

    Zirker, L.R.; Francfort, J.E.

    2003-01-31

    This report details the initial activities to evaluate the performance of the oil bypass filter technology being tested by the Idaho National Engineering and Environmental Laboratory (INEEL) for the U.S. Department of Energy's FreedomCAR & Vehicle Technologies Program. Eight full-size, four-cycle diesel-engine buses used to transport INEEL employees on various routes have been equipped with oil bypass systems from the puraDYN Corporation. Each bus averages about 60,000 miles a year. The evaluation includes an oil analysis regime to monitor the presence of necessary additives in the oil and to detect undesirable contaminants. Very preliminary economic analysis suggests that the oil bypass system can reduce life-cycle costs. As the evaluation continues and oil avoidance costs are quantified, it is estimated that the bypass system economics may prove increasingly favorable, given the anticipated savings in operational costs and in reduced use of oil and waste oil avoidance.

  11. Investigation of transfer characteristics of high performance graphene flakes.

    Science.gov (United States)

    Venugopal, Gunasekaran; Krishnamoorthy, Karthikeyan; Kim, Sang-Jae

    2013-05-01

    In this article, we attempted a study on field effect transport characteristics of graphene flakes. These graphene flakes were exfoliated by mechanical peeling-off technique and the electrical contacts were patterned by photo-lithographic method. Graphene devices have shown better transfer characteristics which was obtained even in low-voltage (graphene transistors were patterned on oxidized silicon wafers. A clear n-type to p-type transition at Dirac point and higher electron drain-current modulation in positive back-gate field with current minimum (the Dirac point) were observed at V(GS) = -1.7 V. The carrier mobility was determined from the measured transconductance. The transconductance of the graphene transistors was observed as high as 18.6 microS with a channel length of 68 microm. A maximum electron mobility of 1870 +/- 143 cm2/V x s and hole mobility of 1050 +/- 35 cm2/V x s were achieved at a drain bias 2.1 V which are comparatively higher values among reported for mechanically exfoliated graphene using lithographic method. The fabricated devices also sustained with high-current density for 40 hr in continuous operation without any change in device resistance, which could be applied for robust wiring applications.

  12. Technology-Supported Performance Assessments for Middle School Geoscience

    Science.gov (United States)

    Zalles, D. R.; Quellmalz, E.; Rosenquist, A.; Kreikemeier, P.

    2002-12-01

    Under funding from the World Bank, the U.S. Department of Education, the National Science Foundation, and the Federal Government's Global Learning and Observations to Benefit the Environment Program (GLOBE), SRI International has developed and piloted web-accessible performance assessments that measure K-12 students' abilities to use learning technologies to reason with scientific information and communicate evidence-based conclusions to scientific problems. This presentation will describe the assessments that pertain to geoscience at the middle school level. They are the GLOBE Assessments and EPA Phoenix, an instantiation of SRI's model of assessment design known as Integrative Performance Assessments in Technology (IPAT). All are publicly-available on the web. GLOBE engages students in scientific data collection and observation about the environment. SRI's classroom assessments for GLOBE provide sample student assessment tools and frameworks that allow teachers and students to assess how well students can use the data in scientific inquiry projects. Teachers can use classroom assessment tools on the site to develop integrated investigations for assessing GLOBE within their particular science curricula. Rubrics are provided for measuring students' GLOBE-related skills, and alignments are made to state, national, and international science standards. Sample investigations are provided about atmosphere, hydrology, landcover, soils, earth systems, and visualizations. The IPAT assessments present students with engaging problems rooted in science or social science content, plus sets of tasks and questions that require them to gather relevant information on the web, use reasoning strategies to analyze and interpret the information, use spreadsheets, word processors, and other productivity tools, and communicate evidence-based findings and recommendations. In the process of gathering information and drawing conclusions, students are assessed on how well they can operate

  13. Aerodynamic characteristics and heat radiation performance of sportswear fabrics

    Science.gov (United States)

    Koga, H.; Hiratsuka, M.; Ito, S.; Konno, A.

    2017-10-01

    Sports such as swimming, speed skating, and marathon are sports competing for time. In recent years, reduction of the fluid drag of sportswear is required for these competitions in order to improve the record. In addition, sweating and discomfort due to body temperature rise during competition are thought to affect competitor performance, and heat radiation performance is also an important factor for sportswear. The authors have measured fluid force drag by wrapping cloth around a cylinder and have confirmed their differences due to the roughness of the fabric surface, differences in sewing. The authors could be verified the drag can be reduced by the position of the wear stitch. This time, we measured the heat radiation performance of 14 types of cloths whose aero dynamic properties are known using cylinders which are regarded as human fuselages, and found elements of cloth with heat radiation performance. It was found to be important for raising the heat radiation performance of sportswear that the fabric is thin and flat surface processing.

  14. THE USE OF NEURAL NETWORK TECHNOLOGY TO MODEL SWIMMING PERFORMANCE

    Directory of Open Access Journals (Sweden)

    António José Silva

    2007-03-01

    Full Text Available The aims of the present study were: to identify the factors which are able to explain the performance in the 200 meters individual medley and 400 meters front crawl events in young swimmers, to model the performance in those events using non-linear mathematic methods through artificial neural networks (multi-layer perceptrons and to assess the neural network models precision to predict the performance. A sample of 138 young swimmers (65 males and 73 females of national level was submitted to a test battery comprising four different domains: kinanthropometric evaluation, dry land functional evaluation (strength and flexibility, swimming functional evaluation (hydrodynamics, hydrostatic and bioenergetics characteristics and swimming technique evaluation. To establish a profile of the young swimmer non-linear combinations between preponderant variables for each gender and swim performance in the 200 meters medley and 400 meters font crawl events were developed. For this purpose a feed forward neural network was used (Multilayer Perceptron with three neurons in a single hidden layer. The prognosis precision of the model (error lower than 0.8% between true and estimated performances is supported by recent evidence. Therefore, we consider that the neural network tool can be a good approach in the resolution of complex problems such as performance modeling and the talent identification in swimming and, possibly, in a wide variety of sports

  15. Investigation on heat transfer characteristics and flow performance of Methane at supercritical pressures

    Science.gov (United States)

    Xian, Hong Wei; Oumer, A. N.; Basrawi, F.; Mamat, Rizalman; Abdullah, A. A.

    2018-04-01

    The aim of this study is to investigate the heat transfer and flow characteristic of cryogenic methane in regenerative cooling system at supercritical pressures. The thermo-physical properties of supercritical methane were obtained from the National institute of Standards and Technology (NIST) webbook. The numerical model was developed based on the assumptions of steady, turbulent and Newtonian flow. For mesh independence test and model validation, the simulation results were compared with published experimental results. The effect of four different performance parameter ranges namely inlet pressure (5 to 8 MPa), inlet temperature (120 to 150 K), heat flux (2 to 5 MW/m2) and mass flux (7000 to 15000 kg/m2s) on heat transfer and flow performances were investigated. It was found that the simulation results showed good agreement with experimental data with maximum deviation of 10 % which indicates the validity of the developed model. At low inlet temperature, the change of specific heat capacity at near-wall region along the tube length was not significant while the pressure drop registered was high. However, significant variation was observed for the case of higher inlet temperature. It was also observed that the heat transfer performance and pressure drop penalty increased when the mass flux was increased. Regarding the effect of inlet pressure, the heat transfer performance and pressure drop results decreased when the inlet pressure is increased.

  16. Exploring the Technological Collaboration Characteristics of the Global Integrated Circuit Manufacturing Industry

    Directory of Open Access Journals (Sweden)

    Yun Liu

    2018-01-01

    Full Text Available With the intensification of international competition, there are many international technological collaborations in the integrated circuit manufacturing (ICM industry. The importance of improving the level of international technological collaboration is becoming more and more prominent. Therefore, it is vital for a country, a region, or an institution to understand the international technological collaboration characteristics of the ICM industry and, thus, to know how to enhance its own international technological collaboration. This paper depicts the international technological collaboration characteristics of the ICM industry based on patent analysis. Four aspects, which include collaboration patterns, collaboration networks, collaboration institutions, and collaboration impacts, are analyzed by utilizing patent association analysis and social network analysis. The findings include the following: first, in regard to international technological collaboration, the USA has the highest level, while Germany has great potential for future development; second, Asia and Europe have already formed clusters, respectively, in the cooperative network; last, but not least, research institutions, colleges, and universities should also actively participate in international collaboration. In general, this study provides an objective reference for policy making, competitiveness, and sustainability in the ICM industry. The framework presented in this paper could be applied to examine other industrial international technological collaborations.

  17. Performing in Glass: Reproduction, Technology, \\ud Performance and the Bio-Spectacular

    OpenAIRE

    Furse, Anna F. D.

    2006-01-01

    Feminist Futures? sets out to ask if and in what ways feminism remains relevant to theatre and performance practice of the twenty-first century. Responding to this question is an excellent, cross-generational mix of theatre scholars and practitioners whose essays engage in lively, cutting edge critical debates on issues such as citizenship, autobiography, cultural heritage, political agency, and body/technology, as circulating in contemporary feminism and performance today. A timely contribut...

  18. Benchmarking and Performance Improvement at Rocky Flats Environmental Technology Site

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, C. [Kaiser-Hill Co., LLC, Golden, CO (United States)], Doyle, D. [USDOE Rocky Flats Office, Golden, CO (United States)], Featherman, W.D. [Project Performance Corp., Sterline, VA (United States)

    1997-12-31

    The Rocky Flats Environmental Technology Site (RFETS) has initiated a major work process improvement campaign using the tools of formalized benchmarking and streamlining. This paper provides insights into some of the process improvement activities performed at Rocky Flats from November 1995 through December 1996. It reviews the background, motivation, methodology, results, and lessons learned from this ongoing effort. The paper also presents important gains realized through process analysis and improvement including significant cost savings, productivity improvements, and an enhanced understanding of site work processes.

  19. Predicting Performance Under Acute Stress : The Role of Individual Characteristics

    NARCIS (Netherlands)

    Delahaij, R.; Dam, K. van; Gaillard, A.W.K.; Soeters, J.

    2011-01-01

    This prospective study examined how differences in coping style, coping self-efficacy, and metacognitive awareness influence coping behavior and performance during a realistic acute stressful exercise in 2 military samples (n = 122 and n = 132). Results showed that coping self-efficacy and coping

  20. Performance characteristics and blood profile of West African dwarf ...

    African Journals Online (AJOL)

    A twelve week trial was investigated to evaluate performance and blood profile of West African dwarf (WAD) goats fed malted sorghum sprout with pineapple waste (MSPW) based diet. The malted sorghum sprout and pineapple waste was at ratio 1:2 (weight/weight) respectively. Sixteen WAD goats with average initial ...

  1. Job characteristics, flow, and performance : the moderating role of conscientiousness

    NARCIS (Netherlands)

    Demerouti, E.

    2006-01-01

    The present article aims to show the importance of positive work-related experiences within occupational health psychology by examining the relationship between flow at work (i.e., absorption, work enjoyment, and intrinsic work motivation) and job performance. On the basis of the literature, it was

  2. Performance gaps in energy consumption : household groups and building characteristics

    NARCIS (Netherlands)

    van den Brom, P.I.; Meijer, A.; Visscher, H.J.

    2017-01-01

    The difference between actual and calculated energy is called the ‘energy-performance gap’. Possible explanations for this gap are construction mistakes, improper adjusting of equipment, excessive simplification in simulation models and occupant behaviour. Many researchers and governmental

  3. Performance and carcass characteristics of Japanese quail as ...

    African Journals Online (AJOL)

    The effect of sex and the supplementation of the prebiotic, mannan oligosaccharides (MOS), the acidifier, calcium propionate (CPr) or their combination in the feed of Japanese quail (Coturnix japonica) on their performance and carcass quality was examined in this experimentation. Three hundred, 1-day old Japanese quail ...

  4. Southern hemisphere coal characteristics and their impact on plant performance

    Energy Technology Data Exchange (ETDEWEB)

    Chiou, Y Y; Dickson, A J; Lowe, A; Pearson, J M; Pitman, B L; Semark, P M [Taiwan Power Company (Taiwan)

    1992-09-01

    The paper reports performance information of specific utilities fired by coal mined in the Southern Hemisphere. It includes information from Pacific Power Services, Australia, the China Light and Power Company, Hong Kong, the Taiwan Power Company, Taiwan, and the South Africa Electricity Power Company, South Africa. 12 refs., 3 figs., 12 tabs.

  5. Sibsize, Family Environment, Cognitive Performance, and Affective Characteristics

    Science.gov (United States)

    Marjoribanks, Kevin

    1976-01-01

    Incorporates measures of family environment (parent-child interaction) into research methodology to study the effects of sibsize (family size and birth order) on a child's cognitive performance and affective behavior. Provides tentative support for the confluence model of sibsize influences on children's behaviors. (RL)

  6. PGF2α induced estrus characteristics and reproductive performance ...

    African Journals Online (AJOL)

    Structured questionnaire and a field survey were applied on a total of 200 randomly selected households. ... Records of animal identification, parameters of reproductive performance such as weaning age and age at puberty, litter size, kidding interval (KI), the type of management practice and clinical parameters were taken ...

  7. Mining and technological characteristics of future open-pit mine at Brod-Gneotino

    International Nuclear Information System (INIS)

    Tasevski, Apostol; Demjanski, Kiril; And others

    2005-01-01

    Development program of Electric Power Company of Macedonia includes to open several pits of coal with aim to prolongate the working period of TPP Bitola, of which one is the bed Brod-Gneotino. This coal bed is characterized with some characteristic mining and technological parameters described in thi paper. (Author)

  8. Radical production efficiency and electrical characteristics of a coplanar barrier discharge built by multilayer ceramic technology

    DEFF Research Database (Denmark)

    Jõgi, Indrek; Erme, Kalev; Levoll, Erik

    2017-01-01

    The present study investigated the electrical characteristics and radical production efficiency of a coplanar barrier discharge (CBD) device manufactured by Kyocera by multilayer ceramic technology. The device consisted of a number of linear electrodes with electrode and gap widths of 0.75 mm...

  9. Students' Characteristics, Self-Regulated Learning, Technology Self-Efficacy, and Course Outcomes in Online Learning

    Science.gov (United States)

    Wang, Chih-Hsuan; Shannon, David M.; Ross, Margaret E.

    2013-01-01

    The purpose of this study was to examine the relationship among students' characteristics, self-regulated learning, technology self-efficacy, and course outcomes in online learning settings. Two hundred and fifty-six students participated in this study. All participants completed an online survey that included demographic information, the modified…

  10. Path creation in Nordic energy and road transport systems – The role of technological characteristics

    DEFF Research Database (Denmark)

    Hansen, Teis; Klitkou, Antje; Borup, Mads

    2017-01-01

    This paper reviews path-creation processes in road transport systems in the Nordic countries: e-mobility in Denmark, hydrogen and fuel-cell electrical vehicles in Norway, and advanced biofuels in Finland and Sweden. The study builds on the path creation literature, which seeks to explain the emer......This paper reviews path-creation processes in road transport systems in the Nordic countries: e-mobility in Denmark, hydrogen and fuel-cell electrical vehicles in Norway, and advanced biofuels in Finland and Sweden. The study builds on the path creation literature, which seeks to explain...... the emergence of new technological pathways. Drawing on recent insights concerning the differences between design- and manufacturing-intensive technologies, the paper analyses the influence of technological characteristics on path creation processes. The case comparison indicates that technological...... characteristics seem to have greater influence on the content of activities in the later phase rather than the early phase of path creation processes. The analysis also emphasises that barriers to path creation processes differ depending on technological characteristics. This highlights the importance...

  11. Suns-VOC characteristics of high performance kesterite solar cells

    Science.gov (United States)

    Gunawan, Oki; Gokmen, Tayfun; Mitzi, David B.

    2014-08-01

    Low open circuit voltage (VOC) has been recognized as the number one problem in the current generation of Cu2ZnSn(Se,S)4 (CZTSSe) solar cells. We report high light intensity and low temperature Suns-VOC measurement in high performance CZTSSe devices. The Suns-VOC curves exhibit bending at high light intensity, which points to several prospective VOC limiting mechanisms that could impact the VOC, even at 1 sun for lower performing samples. These VOC limiting mechanisms include low bulk conductivity (because of low hole density or low mobility), bulk or interface defects, including tail states, and a non-ohmic back contact for low carrier density CZTSSe. The non-ohmic back contact problem can be detected by Suns-VOC measurements with different monochromatic illuminations. These limiting factors may also contribute to an artificially lower JSC-VOC diode ideality factor.

  12. Performance characteristics of aerodynamically optimum turbines for wind energy generators

    Science.gov (United States)

    Rohrbach, C.; Worobel, R.

    1975-01-01

    This paper presents a brief discussion of the aerodynamic methodology for wind energy generator turbines, an approach to the design of aerodynamically optimum wind turbines covering a broad range of design parameters, some insight on the effect on performance of nonoptimum blade shapes which may represent lower fabrication costs, the annual wind turbine energy for a family of optimum wind turbines, and areas of needed research. On the basis of the investigation, it is concluded that optimum wind turbines show high performance over a wide range of design velocity ratios; that structural requirements impose constraints on blade geometry; that variable pitch wind turbines provide excellent power regulation and that annual energy output is insensitive to design rpm and solidity of optimum wind turbines.

  13. Electrical performance characteristics of the SSC Accelerator System String Test

    International Nuclear Information System (INIS)

    Robinson, W.; Burgett, W.; Dombeck, T.; Gannon, J.; Kraushaar, P.; McInturff, A.; Savord, T.; Tool, G.

    1993-05-01

    The string test facility was constructed to provide a development test bed for the arc regions of the Superconducting Super Collider (SSC). Significant effort has been devoted to the development and testing of superconducting magnets, spools, and accelerator control systems required for the SSC. The string test facility provides the necessary environment required to evaluate the operational performance of these components as they are configured as an accelerator lens in the collider. This discussion will review the results of high current testing of the string conducted to evaluate magnet element uniformity and compatibility, the splice resistance used to connect the magnets, and system response to various quench conditions. Performance results of the spools, energy bypass systems, energy dump, and the power supply system are also discussed

  14. Electrical performance characteristics of the SSC Accelerator System String Test

    International Nuclear Information System (INIS)

    Robinson, W.; Burgett, W.; Dombeck, T.; Gannon, J.; Kraushaar, P.; McInturff, A.; Savord, T.; Tool, G.

    1993-01-01

    The string test facility was constructed to provide a development test bed for the arc regions of the Superconducting Super Collider (SSC). Significant effort has been devoted to the development and testing of superconducting magnets, spools, and accelerator control systems required for the SSC. The string test facility provides the necessary environment required to evaluate the operational performance of these components as they are configured as an accelerator lens in the collider. This discussion will review the results of high current testing of the string conducted to evaluate magnet element uniformity and compatibility, the splice resistance used to connect the magnets, and system response to various quench conditions. Performance results of the spools, energy bypass systems, energy dump, and the power supply system are also discussed

  15. The HARP resistive plate chambers: Characteristics and physics performance

    International Nuclear Information System (INIS)

    Ammosov, V.; Boyko, I.; Chelkov, G.; Dedovitch, D.; Dumps, R.; Dydak, F.; Elagin, A.; Gapienko, V.; Gostkin, M.; Guskov, A.; Kroumchtein, Z.; Koreshev, V.; Linssen, L.; Nefedov, Yu.; Nikolaev, K.; Semak, A.; Sviridov, Yu.; Usenko, E.; Wotschack, J.; Zaets, V.; Zhemchugov, A.

    2007-01-01

    The HARP Resistive Plate Chamber (RPC) system was designed for time-of-flight measurement in the large-angle acceptance region of the HARP spectrometer. It comprised 46 four-gap glass RPCs covering an area of ∼8m 2 . The design of the RPCs, their operation, intrinsic properties, and system performance are described. The intrinsic time resolution of the RPCs is better than 130ps leading to a system time resolution of ∼175ps

  16. The performance characteristics of groundnut ( Arachis hypogea , L ...

    African Journals Online (AJOL)

    The ethyl-esters were blended with automotive gas oil at (0 to 20%) mix with 5% increment of groundnut ethyl-esters to produce biodiesel. The performance of a 2.46 kW diesel engine was evaluated using the groundnut biodiesel at five loading conditions (0, 25, 50, 75 and 100% of full load). Automotive gas oil was used as ...

  17. The characteristics and performance of international joint ventures in Thailand

    OpenAIRE

    Suwannarat, P

    2010-01-01

    The importance of strategic alliances in the form of international joint ventures (IJVs) is growing in the present international business environment where competition is on a global scale. A review of the IJV literature, especially in developing countries, shows an over-emphasis on China and the NIEs (the first tier newly-industrialising economies: Taiwan, Singapore, Hong Kong, and South Korea). To date, relatively little attention has been paid to the ASEAN4 countries (the high-performing e...

  18. Assessment of corrosion characteristics and development of remedial technologies in nuclear materials

    International Nuclear Information System (INIS)

    Kim, Joung Soo; Kim, H. P.; Lim, Y. S. and others

    2005-04-01

    Main components and structures in nuclear power plants generally use materials having superior resistance to corrosion. Since the damages related to corrosion have become a menace to the safety of NPPs as well as economical loss and the steam generator tubing forming a boundary between the primary and secondary sides of NPPs is one of the main components that are most damaged by corrosion, it is strongly required to verify the mechanisms of the steam generator tubing degradations, to develop remedial techniques for the degradations, to manage the damages, and to develop techniques for the extension of the plant's life. In this study, the PWSCC characteristics of the archived steam generator tube materials in the domestic NPPs were evaluated and the databases of the obtained results were established. Also, the PWSCC characteristics of the welding material, Alloy 182, for Alloy 600, were evaluated. To verify the damage mechanisms of the circumferential SCC occurring in the expansion transition region of the tubes in the Korean standard NPPS, the evaluation technique for the residual stresses in the expanded region was acquired. A procedure of the inhibition technique for the SCC occurring in the secondary side of steam generators and a model for estimating the safety of damaged tubes by the structural leakage were developed, by which the fundamental technologies for the safe operations of NPPs, the management of the damages, and the expansion of the plant life were acquired. The material improvement technique for the integrity enhancement of tubes was developed. Along with the development of the Ni-coating technique the evaluation of the properties such as mechanical and SCC properties of the coated film was performed

  19. Adaptation and learning: characteristic time scales of performance dynamics.

    Science.gov (United States)

    Newell, Karl M; Mayer-Kress, Gottfried; Hong, S Lee; Liu, Yeou-Teh

    2009-12-01

    A multiple time scales landscape model is presented that reveals structures of performance dynamics that were not resolved in the traditional power law analysis of motor learning. It shows the co-existence of separate processes during and between practice sessions that evolve in two independent dimensions characterized by time scales that differ by about an order of magnitude. Performance along the slow persistent dimension of learning improves often as much and sometimes more during rest (memory consolidation and/or insight generation processes) than during a practice session itself. In contrast, the process characterized by the fast, transient dimension of adaptation reverses direction between practice sessions, thereby significantly degrading performance at the beginning of the next practice session (warm-up decrement). The theoretical model fits qualitatively and quantitatively the data from Snoddy's [Snoddy, G. S. (1926). Learning and stability. Journal of Applied Psychology, 10, 1-36] classic learning study of mirror tracing and other averaged and individual data sets, and provides a new account of the processes of change in adaptation and learning. 2009 Elsevier B.V. All rights reserved.

  20. A review on the engine performance and exhaust emission characteristics of diesel engines fueled with biodiesel blends.

    Science.gov (United States)

    Damanik, Natalina; Ong, Hwai Chyuan; Tong, Chong Wen; Mahlia, Teuku Meurah Indra; Silitonga, Arridina Susan

    2018-06-01

    Biodiesels have gained much popularity because they are cleaner alternative fuels and they can be used directly in diesel engines without modifications. In this paper, a brief review of the key studies pertaining to the engine performance and exhaust emission characteristics of diesel engines fueled with biodiesel blends, exhaust aftertreatment systems, and low-temperature combustion technology is presented. In general, most biodiesel blends result in a significant decrease in carbon monoxide and total unburned hydrocarbon emissions. There is also a decrease in carbon monoxide, nitrogen oxide, and total unburned hydrocarbon emissions while the engine performance increases for diesel engines fueled with biodiesels blended with nano-additives. The development of automotive technologies, such as exhaust gas recirculation systems and low-temperature combustion technology, also improves the thermal efficiency of diesel engines and reduces nitrogen oxide and particulate matter emissions.

  1. Performance Enhancement of the Patch Antennas Applying Micromachining Technology

    Directory of Open Access Journals (Sweden)

    Mohamed N. Azermanesh

    2007-09-01

    Full Text Available This paper reports on the application of micromachining technology for performance enhancement of two types of compact antennas which are becoming a common practice in microsystems. Shorted patch antennas (SPA and folded shorted patch antennas operating in the 5-6 GHz ISM band, with intended application in short-range wireless communications, are considered. The electrical length of antennas are modified by etching the substrate of the antennas, thus providing a new degree of freedom to control the antenna operating properties, which is the main novelty of our work. The gain and bandwidth of the antennas are increased by increasing the etching depth. However, etching the substrate affects the operating frequency as well. To keep the operating frequency at a pre-specified value, the dimension of the antennas must be increased by deepening the etching depth. Therefore, a trade off between the performance enhancement of the antennas and the dimensional enlargement is required.

  2. Enhancing performance and reducing stress in sports technological advances

    CERN Document Server

    Ivancevic, Tijana; Greenberg, Ronald

    2015-01-01

    This book is designed to help athletes and individuals interested in high sports performance in their journey towards the perfection of human sports abilities and achievements. It has two main goals: accelerating the acquisition of motor skills and preparing and vigilantly reducing the recovery time after training and competition. The Diamond Sports Protocol (DSP) presents state-of-the-art techniques for current sport and health technologies, particularly neuromuscular electrical stimulation (Sports Wave), oxygen infusion (Oxy Sports), infrared (Sports Infrared Dome) and lactic acid cleaning (Turbo Sports). The book suggest DSP as an essential part of every future athlete's training, competition and health maintenance. The book is for everyone interested in superior sports performance, fast and effective rehabilitation from training and competition and sports injury prevention.

  3. Performance characteristics of a self-sealing/self-healing barrier

    International Nuclear Information System (INIS)

    McGregor, R.G.; Stegemann, J.A.

    1997-01-01

    Environment Canada and the Netherlands Energy Research Foundation are co-developers of a patented Self-Sealing/Self-Healing (SS/SH) Barrier system for containment of wastes which is licensed to Water Technology International Corporation. The SS/SH Barrier is intended for use as either a liner or cover for landfills, contaminated sites, secondary containment areas, etc., in the industrial, chemical, mining and municipal sectors, and also as a barrier to hydraulic flow for the transportation and construction industry. The SS/SH Barrier's most significant feature is its capability for self-repair in the event of a breach. By contrast, conventional barrier systems, such as clay, geomembrane, or geosynthetic clay liners can not be repaired without laborious excavation and reconstruction. Laboratory investigations have shown that the SS/SH Barrier concept will function with a variety of reactive materials. Self-Sealing/Self-Healing Barriers are cost competitive and consistently exhibit hydraulic conductivities ranging from 10 -9 to 10 -13 m/s, which decrease with time. These measurements meet or exceed the recommended hydraulic conductivity required by EPA for clay liners ( -9 m/s) used in landfills and hazardous waste sites. Results of mineralogical examination of the seal, diffusion testing, hydraulic conductivity measurement, and durability testing, including wet/dry, freeze/thaw cycling and leachate compatibility are also presented

  4. Characteristics of sprint performance in college football players.

    Science.gov (United States)

    Brechue, William F; Mayhew, Jerry L; Piper, Fontaine C

    2010-05-01

    To investigate sprinting strategy, acceleration and velocity patterns were determined in college football players (n = 61) during performance of a 9.1-, 36.6-, and 54.9-m sprints. Acceleration and velocity were determined at 9.1-m intervals during each sprint. Lower-body strength and power were evaluated by 1 repetition maximum (1-RM) squat, power clean, jerk, vertical jump, standing long jump, and standing triple jump. Sprint times averaged 1.78 +/- 0.11 seconds (9.1 m), 5.18 +/- 0.35 seconds (36.6 m), and 7.40 +/- 0.53 seconds. Acceleration peaked at 9.1 m (2.96 +/- 0.44 m x s(-2)), was held constant at 18.3 m (3.55 +/- 0.0.94 m x s(-2)), and was negative at 27.4 m (-1.02 +/- 0.72 m x s(-2)). Velocity peaked at 18.3 m (8.38 +/- 0.65 m x s(-2)) and decreased slightly, but significantly at 27.4 m (7.55 +/- 0.66 m x s(-2)), associated with the negative acceleration. Measures of lower-body strength were significantly related to acceleration, velocity, and sprint performance only when corrected for body mass. Lower-body strength/BM and power correlated highest with 36.6-m time (rs = -0.55 to -0.80) and with acceleration (strength r = 0.67-0.49; power r = 0.73-0.81) and velocity (strength r = 0.68-0.53; power r = 0.74-0.82) at 9.1 m. Sprint times and strength per body mass were significantly lower in lineman compared with linebackers-tight ends and backs. The acceleration and velocity patterns were the same for each position group, and differences in sprint time were determined by the magnitude of acceleration and velocity at 9.1 and 18.3 m. Sprint performance in football players is determined by a rapid increase in acceleration (through 18.3 m) and a high velocity maintained throughout the sprint and is independent of position played. The best sprint performances (independent of sprint distance) appear to be related to the highest initial acceleration (through 18.3 m) and highest attained and maintained velocity. Strength relative to body mass and power appears to

  5. Survey of LWR environmental control technology performance and cost

    International Nuclear Information System (INIS)

    Heeb, C.M.; Aaberg, R.L.; Cole, B.M.; Engel, R.L.; Kennedy, W.E. Jr.; Lewallen, M.A.

    1980-03-01

    This study attempts to establish a ranking for species that are routinely released to the environment for a projected nuclear power growth scenario. Unlike comparisons made to existing standards, which are subject to frequent revision, the ranking of releases can be used to form a more logical basis for identifying the areas where further development of control technology could be required. This report describes projections of releases for several fuel cycle scenarios, identifies areas where alternative control technologies may be implemented, and discusses the available alternative control technologies. The release factors were used in a computer code system called ENFORM, which calculates the annual release of any species from any part of the LWR nuclear fuel cycle given a projection of installed nuclear generation capacity. This survey of fuel cycle releases was performed for three reprocessing scenarios (stowaway, reprocessing without recycle of Pu and reprocessing with full recycle of U and Pu) for a 100-year period beginning in 1977. The radioactivity releases were ranked on the basis of a relative ranking factor. The relative ranking factor is based on the 100-year summation of the 50-year population dose commitment from an annual release of radioactive effluents. The nonradioactive releases were ranked on the basis of dilution factor. The twenty highest ranking radioactive releases were identified and each of these was analyzed in terms of the basis for calculating the release and a description of the currently employed control method. Alternative control technology is then discussed, along with the available capital and operating cost figures for alternative control methods

  6. Advanced digital technology - improving nuclear power plant performance through maintainability

    International Nuclear Information System (INIS)

    Ford, J.L.; Senechal, R.R.; Altenhein, G.D.; Harvey, R.P.

    1998-01-01

    In today's energy sector there is ever increasing pressure on utilities to operate power plants at high capacity factors. To ensure nuclear power is competitive into the next century, it is imperative that strategic design improvements be made to enhance the performance of nuclear power plants. There are a number of factors that affect a nuclear power plant's performance; lifetime maintenance is one of the major contributors. The maturing of digital technology has afforded ABB the opportunity to make significant design improvements in the area of maintainability. In keeping with ABB's evolutionary advanced nuclear plant design approach, digital technology has systematically been incorporated into the control and protection systems of the most recent Korean nuclear units in operation and under construction. One example of this was the multi-functional design team approach that was utilized for the development of ABB's Digital Plant Protection System (DPPS). The design team consisted of engineers, maintenance technicians, procurement specialists and manufacturing personnel in order to provide a complete perspective on all facets of the design. The governing design goals of increased reliability and safety, simplicity of design, use of off-the-shelf products and reduced need for periodic surveillance testing were met with the selection of proven ABB-Advant Programmable Logic Controllers (PLCs) as the heart of the DPPS. The application of digital PLC technology allows operation for extended periods without requiring routine maintenance or re-calibration. A well documented commercial dedication program approved by the United States Nuclear Regulatory Commission (US NRC) as part of the System 80+ TM Advanced Light Water Reactor Design Certification Program, allowed the use of off-the shelf products in the design of the safety protection system. In addition, a number of mechanical and electrical improvements were made which support maintainability. The result is a DPPS

  7. Performance Criteria for Capture and/or Immobilization Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, R. T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, S. H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Strachan, D. M. [Strata-G, LLC, Knoxville, TN (United States); Soelberg, N. R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Spencer, B. B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Riley, B. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-02-01

    The capture and subsequent immobilization of the four volatile radionuclides (3H, 14C, 85Kr, and 129I) from the off-gas streams of a used nuclear fuel reprocessing facility has been a topic of substantial research interest for the US DOE and international colleagues. Regulations set forth by the US EPA direct that some or all of these radionuclides (based upon fuel burnup, fuel type, cooling time, etc.) will require removal, to some extent, from the plant effluent streams prior to discharge to the environment. Upon removal, the radionuclide, as well as any associated sorbent, is destined for waste. Research of separation and capture methodologies has included a wide range of technologies including liquid caustic scrubbing systems, solid adsorbents, and cryogenic distillation. The studies of waste forms have been correspondingly diverse. In considering the technologies available for future development and implementation of both sorbents and waste forms, it will be necessary to use benchmarked measures of performance to objectively evaluate each sorbent system or waste form. This document is intended to provide initial guidance on the types of performance criteria for capture materials and waste forms intended for use in the recycling removal and disposal of UNF and, where possible, the minimum acceptable values for those criteria.

  8. Impact of Information and Communication Technologies in International Negotiation Performance

    Directory of Open Access Journals (Sweden)

    Jose Alejandro Cano

    2015-08-01

    Full Text Available Objective – This article establishes relations between the level of importance of Information and Communication Technologies (ICT, the frequency of use of these tools, and the efficiency and efficacy achieved in the international negotiation processes. Design/methodology/approach – A research study is carried out in 180 import and / or export firms in Medellin city, and the proposed relations are explained through a theoretical model. With the information obtained, correlation and comparative analysis of efficiency and efficacy indicators are made. Findings – ICT are essential to perform international processes, therefore the increase in the importance level and frequency of use of these technologies allows perceiving better results about efficiency and efficacy increase. Practical implications – Increasing the application of ICT to the international negotiation processes generates a reduction of cost and time in negotiation and an increase of international sale contract, however ICT must be complemented by other elements such as attitude, training and experience of the negotiator to obtain satisfactory results. Originality/value – The article proposes an original model to study the effect of the importance level and frequency of use of ICT on the performance of international negotiation process.

  9. Evaluation of High-Performance Network Technologies for ITER

    Energy Technology Data Exchange (ETDEWEB)

    Zagar, K.; Kolaric, P.; Sabjan, R.; Zagar, A. [Cosylab d.d., Ljubljana (Slovenia); Hunt, S. [Alceli Hunt Beratung, Meisterschwanden (Switzerland)

    2009-07-01

    To facilitate fast feedback control of plasma, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, four types of high-performance communication have been identified. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024*1024) and frame rate (30 Hz). In this article, we present some combinations of common off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time LINUS operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming. This document is composed of an abstract followed by the presentation transparencies. (authors)

  10. Evaluation of high-performance network technologies for ITER

    Energy Technology Data Exchange (ETDEWEB)

    Zagar, K., E-mail: klemen.zagar@cosylab.co [Cosylab d.d., 1000 Ljubljana (Slovenia); Hunt, S. [Alceli Hunt Beratung, 5616 Meisterschwanden (Switzerland); Kolaric, P.; Sabjan, R.; Zagar, A.; Dedic, J. [Cosylab d.d., 1000 Ljubljana (Slovenia)

    2010-07-15

    For the fast feedback plasma controllers, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, the ITER CODAC team identified four types of high-performance communication applications. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio-Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024 x 1024) and frame rate (30 Hz). In this article, we present some combinations of common-off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time Linux operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming.

  11. Evaluation of high-performance network technologies for ITER

    International Nuclear Information System (INIS)

    Zagar, K.; Hunt, S.; Kolaric, P.; Sabjan, R.; Zagar, A.; Dedic, J.

    2010-01-01

    For the fast feedback plasma controllers, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, the ITER CODAC team identified four types of high-performance communication applications. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio-Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024 x 1024) and frame rate (30 Hz). In this article, we present some combinations of common-off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time Linux operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming.

  12. Characteristics of the life habits of obese students at one of Japan's National Colleges of Technology.

    Science.gov (United States)

    Nagasawa, Yoshinori; Demura, Shin-Ichi; Shimada, Shigeru

    2017-05-17

    Aim This study clarified the characteristics of life habits of obese Japanese male students at the National Colleges of Technology, Japan. Materials and methods Healthy students aged 15-19 years answered a questionnaire containing 21 items on the following five categories of life habits: general exercise, meals, sleeping, leisure activity and illness or injury history. The subjects were divided into three groups based on the criteria of body mass index (BMI) and body fat percentage (%BF): non-obese (%BF time, bedtime and amount of time spent walking, sleeping and watching TV per day were examined using one-way analysis of variance (ANOVA) and chi-square tests for each item. Results The overweight obese and hidden obese groups engaged in less exercise time, were more likely to eat until they were full at meals and were less likely to eat between meals or late at night than the non-obese group. In addition, the non-obese group had significantly later waking times and significantly less TV-watching time than the overweight obese group. There were no significant differences with respect to leisure activity and illness or injury history among the three groups. Many students in all groups had regular waking times and were not performing any leisure activities. Conclusion The findings suggest that obese students may need further guidance to help them maintain a healthy life and appropriate weight.

  13. Performance characteristics of the ARCHITECT anti-HCV assay.

    Science.gov (United States)

    Jonas, Gesa; Pelzer, Claudia; Beckert, Christian; Hausmann, Michael; Kapprell, Hans-Peter

    2005-10-01

    The ARCHITECT Anti-HCV assay is a fully automated high throughput chemiluminescent microparticle immunoassay (CMIA) for the detection of antibodies to structural and nonstructural proteins of the hepatitis C virus (HCV). To further enhance the performance of this test, the assay was modified to improve the specificity for blood donor specimens. The specificity of the enhanced ARCHITECT Anti-HCV assay was evaluated by screening blood donor samples randomly collected from various German blood banks, as well as hospitalized patient samples derived from Germany and the US. Additionally, antibody sensitivity was determined on commercially available anti-HCV seroconversion panels and on a commercially available worldwide anti-HCV genotype performance panel. Apparent specificity of the modified ARCHITECT Anti-HCV assay in a blood donor population consisting of 3811 specimens was 99.92%, compared to 99.76% for the current on-market assay. Additionally, antibody sensitivity was determined on commercially available anti-HCV seroconversion panels. Seroconversion sensitivity equivalent to or better than the current on-market product was observed by testing 33 seroconversion panels. This study demonstrates that the modified version of the ARCHITECT Anti-HCV assay shows improved specificity for blood donor specimens compared to the current assay on market without compromising sensitivity. With the availability of the improved ARCHITECT Anti-HCV assay and the recent launch of the ARCHITECT HIV Ag/Ab Combo assay, the ARCHITECT system now offers a full hepatitis/retrovirus menu with excellent performance on a high throughput, random access, automated analyzer, ideally suited for blood screening and diagnostic applications.

  14. Performance characteristics of solar-photovoltaic flywheel-storage systems

    Science.gov (United States)

    Jarvinen, P. O.; Brench, B. L.; Rasmussen, N. E.

    A solar photovoltaic energy flywheel storage and conversion system for residential applications was tested. Performance and efficiency measurements were conducted on the system, which utilizes low loss magnetic bearings, maximum power point tracking of the photovoltaic array, integrated permanent magnet motor generator, and output power conditioning sections of either the stand alone cycloconverter or utility interactive inverter type. The overall in/out electrical storage efficiency of the flywheel system was measured along with the power transfer efficiencies of the individual components and the system spin down tare losses. The system compares favorably with systems which use batteries and inverters.

  15. Performance characteristics of a horizontal axis turbine with fusion winglet

    International Nuclear Information System (INIS)

    Zhu, Bing; Sun, Xiaojing; Wang, Ying; Huang, Diangui

    2017-01-01

    Any technique or method that can improve the efficiency in exploiting renewable wind or marine current energy has got a great significance today. It has been reported that adding a winglet at the tip of the rotor blades on a horizontal axis wind turbine can increase its power performance. The purpose of this paper is to adopt a numerical method to investigate the effects of different winglet configurations on turbine performance, especially focusing on the direction for the winglet tip to point towards (the suction side, pressure side or both sides of the main blade). The results show that the new design of an integrated fusion winglet proposed in this paper can generally improve the main blade's power producing ability, which is further enhanced with the increase of turbine's tip speed ratio with a maximum power augmentation of about 3.96%. No matter which direction the winglet tip faces, the installation angle of the winglet should match well with the real angle of incoming flow. As a whole, the turbine with winglet of two tips facing to both sides of the main blade can produce much more power than the one of winglet configuration whose tip faces only one side for different blade hub pitch angles and vast majority of tip speed ratios. The working principle behind the winglet in improving turbine performance may be that it can block the downwash fluid easily flowing around the tip section of the main blade from the pressure side to suction side, and hence diffuse and spread out the tip vortex. As a result, it finally decreases the energy loss. Besides, the relative projected rotor area in incoming flow direction will also be reduced due to the addition of the winglet, which is also helpful to turbine's power coefficient. - Highlights: • Added winglet generally increase the turbine energy extraction performance. • Winglet facing blade both sides is usually superior to that of facing one side. • Winglet can isolate downwash fluid easily flowing

  16. Information Technology Adoption, Corporate Governance and Bank Performance

    Directory of Open Access Journals (Sweden)

    Umi Muawanah

    2018-04-01

    Full Text Available Many academicians and practitioners have been acknowledging that information technology (IT adoption could improve company performance. However, previous research indicates contradictory evidence. These inconsistencies can be attributed to variations among the studies in choosing proxy for IT adoption and due to contingent on other factors. This research aims at analyzing the influence of a contingent factor that is corporate governance (CG concerning the effectiveness of IT adoption in influencing company performance measured by change in return on assets. Two proxies are used for IT adoption: company expenses on IT and the level of the organization managing IT. Data is collected and analyzed from annual reports of all banks listed in Indonesia Stock Exchange from 2011 to 2013. Multiple linear regression models are employed. This research shows that corporate governance practice could improve the effectiveness of IT adoption in improving company performance. This research implies that better CG practices in providing direction and monitoring on IT can lead to better company performance.

  17. Performance characteristics of single effect lithium bromide/ water absorption chiller for small data centers

    Science.gov (United States)

    Mysore, Abhishek Arun Babu

    A medium data center consists of servers performing operations such as file sharing, collaboration and email. There are a large number of small and medium data centers across the world which consume more energy and are less efficient when compared to large data center facilities of companies such as GOOGLE, APPLE and FACEBOOK. Such companies are making their data center facilities more environmental friendly by employing renewable energy solutions such as wind and solar to power the data center or in data center cooling. This not only reduces the carbon footprint significantly but also decreases the costs incurred over a period of time. Cooling of data center play a vital role in proper functioning of the servers. It is found that cooling consumes about 50% of the total power consumed by the data center. Traditional method of cooling includes the use of mechanical compression chillers which consume lot of power and is not desirable. In order to eliminate the use of mechanical compressor chillers renewable energy resources such as solar and wind should be employed. One such technology is solar thermal cooling by means of absorption chiller which is powered by solar energy. The absorption chiller unit can be coupled with either flat plate or evacuated tube collectors in order to achieve the required inlet temperature for the generator of the absorption chiller unit. In this study a modular data center is considered having a cooling load requirement of 23kw. The performance characteristics of a single stage Lithium Bromide/ water refrigeration is presented in this study considering the cooling load of 23kw. Performance characteristics of each of the 4 heat exchangers within the unit is discussed which helps in customizing the unit according to the users' specific needs. This analysis helps in studying the importance of different properties such as the effect of inlet temperatures of hot water for generator, inlet temperatures of cooling water for absorber and

  18. Performance characteristics of ZLC 37 Siemens gamma camera

    International Nuclear Information System (INIS)

    Abdelgadir, Wafaa Abdelrahman

    1994-04-01

    The relationships between the ZLC 37 Siemens γ camera parameters (energy resolution, plane sensitivity, intrinsic uniformity, intrinsic resolution, system uniformity and system resolution) and diagnostic imaging performance was investigated. These parameters when computers when compared with internationally published data showed that the ZLC 37 Siemens γ cameras is in good operative conditions. The effect of the scattering media and WW on the spatial resolution, when the distance is kept fixed were investigated. Comparison of resolution for the media (air, water, water + radioactivity when using WW (10, 15,20%) showed that the resolution is best for air, better for water and worse for water + radioactivity up to a concentration of 8% for a 10% WW. (Author)

  19. Performance characteristics of ZLC 37 Siemens gamma camera

    Energy Technology Data Exchange (ETDEWEB)

    Abdelgadir, Wafaa Abdelrahman [Department of Physics, Faculty of Science, University of Khartoum, Khartoum (Sudan)

    1994-04-01

    The relationships between the ZLC 37 Siemens {gamma} camera parameters (energy resolution, plane sensitivity, intrinsic uniformity, intrinsic resolution, system uniformity and system resolution) and diagnostic imaging performance was investigated. These parameters when computers when compared with internationally published data showed that the ZLC 37 Siemens {gamma} cameras is in good operative conditions. The effect of the scattering media and WW on the spatial resolution, when the distance is kept fixed were investigated. Comparison of resolution for the media (air, water, water + radioactivity) when using WW (10, 15,20%) showed that the resolution is best for air, better for water and worse for water + radioactivity up to a concentration of 8% for a 10% WW. (Author) 28 refs. , 10 tabs. , 22 figs. Also available from the Department of Physics, Faculty of Science, University of Khartoum, Khartoum (SD)

  20. Electrical performance characteristics of the SSC Accelerator System String Test

    International Nuclear Information System (INIS)

    Robinson, W.; Burgett, W.; Gannon, J.; Kraushaar, P.; Mcinturff, A.; Nehring, R.; Saladin, V.; Savord, T.; Sorrensen, G.; Smellie, R.; Tool, G.; Voy, D.

    1993-05-01

    The intent of the Accelerator System String Test (ASST) is to obtain data for model verification and information on the magnitudes of pressures and voltages encountered in an accelerator environment. The ASST milestone run was achieved during July and August, 1992 and consisted of demonstrating the accelerator components could be configured together as a system operating at full current. Following the milestone run, the string was warmed to counteract some design flaws that impeded the operational range. The string was again cooled to cryogenic temperatures in October, and a comprehensive power testing program was conducted through the end of January, 1993. This paper describes how the collider arc components operate in an accelerator environment during quenches induced by firing both strip heaters and spot heaters. Evaluation of the data illustrates how variations in the design parameters on magnets used in a string environment can impact system performance

  1. Performance characteristics of a methanol ejector refrigeration unit

    International Nuclear Information System (INIS)

    Alexis, G.K.; Katsanis, J.S.

    2004-01-01

    This paper discusses the behavior of methanol through an ejector operating in a refrigeration system with a medium temperature thermal source. For detailed calculation of the proposed system, a method has been developed, which employs analytical functions describing the thermodynamic properties of methanol. The proposed cycle has been compared with a Carnot cycle working at the same temperature levels. The influences of three major parameters, generator, condenser and evaporator temperatures, on ejector efficiency and coefficient of performance are discussed. Also, the maximum value of COP was estimated by correlation of the above three temperatures for constant superheated temperature 150 deg. C, and it was 0.139-0.467. The design conditions were generator temperature 117.7-132.5 deg. C, condenser temperature 42-50 deg. C and evaporator temperature -10-5 deg. C

  2. Influence of course characteristics, student characteristics, and behavior in learning management systems on student performance

    NARCIS (Netherlands)

    Conijn, Rianne; Kleingeld, Ad; Matzat, Uwe; Snijders, Chris; van Zaanen, Menno

    2016-01-01

    The use of learning management systems (LMS) in education make it possible to track students’ online behavior. This data can be used for educational data mining and learning analytics, for example, by predicting student performance. Although LMS data might contain useful predictors, course

  3. Separator Characteristics for Increasing Performance of Microbial Fuel Cells

    KAUST Repository

    Zhang, Xiaoyuan

    2009-11-01

    Two challenges for improving the performance of air cathode, single-chamber microbial fuel cells (MFCs) include increasing Coulombic efficiency (CE) and decreasing internal resistance. Nonbiodegradable glass fiber separators between the two electrodes were shown to increase power and CE, compared to cloth separators (J-cloth) that were degraded over time. MFCtestswereconductedusing glass fibermatswith thicknesses of 1.0mm (GF1) or 0.4 mm (GF0.4), a cation exchange membrane (CEM), and a J-cloth (JC), using reactors with different configurations. Higher power densities were obtained with either GF1 (46 ± 4 W/m3) or JC (46 ± 1 W/m3) in MFCs with a 2 cm electrode spacing, when the separator was placed against the cathode (S-configuration), rather than MFCs with GF0.4 (36 ± 1 W/m3) or CEM (14 ± 1 W/m3). Power was increased to 70 ± 2 W/m3 by placing the electrodes on either side of the GF1 separator (single separator electrode assembly, SSEA) and further to 150 ± 6 W/m3 using two sets of electrodes spaced 2 cm a part (double separator electrode assembly, DSEA). Reducing the DSEA electrode spacing to 0.3 cm increased power to 696 ± 26 W/m3 as a result of a decrease in the ohmic resistance from 5.9 to 2.2 Ω. The main advantages of a GF1 separator compared to JC were an improvement in the CE from 40% to 81% (S-configuration), compared to only 20-40% for JC under similar conditions, and the fact that GF1 was not biodegradable. The high CE for the GF1 separator was attributed to a low oxygen mass transfer coefficient (ko ) 5.0 x 10-5 cm/s). The GF1 andJCmaterials differed in the amount of biomass that accumulated on the separator and its biodegradability, which affected long-term power production and oxygen transport. These results show that materials and mass transfer properties of separators are important factors for improving power densities, CE, and long-term performance of MFCs. © 2009 American Chemical Society.

  4. Influence of High Hydrostatic Pressure Technology on Wine Chemical and Sensorial Characteristics: Potentialities and Drawbacks.

    Science.gov (United States)

    Nunes, Cláudia; Santos, Mickael C; Saraiva, Jorge A; Rocha, Sílvia M; Coimbra, Manuel A

    During last years, scientific research on high hydrostatic pressure (HHP) as a nonthermal processing technology for preservation or aging of wine has increased substantially. HHP between 200 and 500MPa is able to inactivate bacteria and yeasts in red and white wines, suggesting that it may be used for wine preservation. However, these treatments have been shown to promote changes on sensorial and physicochemical characteristics in both red and white wines, not immediately in the first month, but along storage. The changes are observed in wine color, aroma, and taste due mainly to reactions of phenolic compounds, sugars, and proteins. These reactions have been associated with those observed during wine aging, leading to aged-like wine characteristics perceived by sensorial analysis. This chapter will present the influence of HHP technology on wine chemical and sensorial characteristics, criticaly discussing its potentialities and drawbacks. The appropriate use of HHP, based on the scientific knowledge of the reactions occuring in wine promoted by HHP, will allow to exploit this technology for wine production achieving distinct characteristics to address particular market and consumer demands. © 2017 Elsevier Inc. All rights reserved.

  5. Runway drainage characteristics related to tire friction performance

    Science.gov (United States)

    Yager, Thomas J.

    1991-01-01

    The capability of a runway pavement to rapidly drain water buildup during periods of precipitation is crucial to minimize tire hydroplaning potential and maintain adequate aircraft ground operational safety. Test results from instrumented aircraft, ground friction measuring vehicles, and NASA Langley's Aircraft Landing Dynamics Facility (ALDF) track have been summarized to indicate the adverse effects of pavement wetness conditions on tire friction performance. Water drainage measurements under a range of rainfall rates have been evaluated for several different runway surface treatments including the transversely grooved and longitudinally grinded concrete surfaces at the Space Shuttle Landing Facility (SLF) runway at NASA Kennedy Space Center in Florida. The major parameters influencing drainage rates and extent of flooding/drying conditions are identified. Existing drainage test data are compared to a previously derived empirical relationship and the need for some modification is indicated. The scope of future NASA Langley research directed toward improving empirical relationships to properly define runway drainage capability and consequently, enhance aircraft ground operational safety, is given.

  6. Performance characteristics of the novel PETRRA positron camera

    CERN Document Server

    Ott, R J; Erlandsson, K; Reader, A; Duxbury, D; Bateman, J; Stephenson, R; Spill, E

    2002-01-01

    The PETRRA positron camera consists of two 60 cmx40 cm annihilation photon detectors mounted on a rotating gantry. Each detector contains large BaF sub 2 scintillators interfaced to large area multiwire proportional chambers filled with a photo-sensitive vapour (tetrakis-(dimethylamino)-ethylene). The spatial resolution of the camera has been measured as 6.5+-1.0 mm FWHM throughout the sensitive field-of-view (FoV), the timing resolution is between 7 and 10 ns FWHM and the detection efficiency for annihilation photons is approx 30% per detector. The count-rates obtained, from a 20 cm diameter by 11 cm long water filled phantom containing 90 MBq of sup 1 sup 8 F, were approx 1.25x10 sup 6 singles and approx 1.1x10 sup 5 cps raw coincidences, limited only by the read-out system dead-time of approx 4 mu s. The count-rate performance, sensitivity and large FoV make the camera ideal for whole-body imaging in oncology.

  7. Effects of Zeolite (Clinoptelolite on Performance Characteristics of

    Directory of Open Access Journals (Sweden)

    A Hassan Abadim

    2011-12-01

    Full Text Available A 70-days experiment was conducted to investigate the effects of natural zeolite (clinoptelolite on the performance of commercial laying hens. 288 Hy-Line W36 strain laying hens (50 weeks old were allotted to 6 dietary treatments including basal diet as control and basal diet supplemented with 1, 2, 3, 4 and 5% zeolite that were fed ad -libitum throughout the experiment. Experimental diets for the 6 treatments were prepared to be iso-caloric and iso-nitrogenous. A completely randomized design with six treatments, eight replicates of six birds per replicate was used at this experiment. Daily feed intake (DFI, feed conversion ratio (FCR, egg production, egg weight, egg white quality, eggshell quality (thickness and percentage and body weight changes were measured during the experiment. Results of this experiment showed that DFI, FCR, egg production and egg abnormality were not significantly (P>0.05 affected by zeolite supplementation. Zeolite supplementation significantly increased egg weight, eggshell thickness and live body weight gain of the hens. Dietary zeolite significantly decreased haugh unit of the eggs. In conclusion, natural zeolite significantly improved egg weight and eggshell quality, decreased haugh unit and live weight gain, and had no significant effects on other parameters.

  8. Development of fuel performance and thermal hydraulic technology

    International Nuclear Information System (INIS)

    Jung, Youn Ho; Song, K. N.; Kim, H. K. and others

    2000-03-01

    Space grid in LWR fuel assembly is a key structural component to support fuel rods and to enhance heat transfer from fuel rod to the coolant. Therefore, the original spacer grid has been developed. In addition, new phenomena in fuel behavior occurs at the high burnup, so that models to analyze those new phenomena were developed. Results of this project can be summarized as follows. - Seven different spacer grid candidates have been invented and submitted for domestic and US patents. Spacer grid test specimen(3x3 array and 5x5 array) were fabricated for each candidate and the mechanical tests were performed. - Basic technologies in the mechanical and thermal hydraulic behavior in the spacer grid development are studied and relevant test facilities were established - Fuel performance analysis models and programs were developed for the high burnup pellet and cladding, and fuel performance data base were compiled - Procedures of fuel characterization and in-/out of-pile tests were prepared - Conceptual design of fuel rod for integral PWR was carried out. (author)

  9. Digital Technologies and performative pedagogies: Repositioning the visual

    Directory of Open Access Journals (Sweden)

    Kathryn Grushka

    2010-05-01

    Full Text Available Images are becoming a primary means of information presentation in the digitized global media and digital technologies have emancipated and democratized the image. This allows for the reproduction and manipulation of images on a scale never seen before and opens new possibilities for teachers schooled in critical visuality. This paper reports on an innovative pre-service teacher training course in which a cross-curricula cohort of secondary teachers employed visual performative competencies to produce a series of learning objects on a digital platform. The resulting intertextual narratives demonstrate that the manipulation of image and text offered by digital technologies create a powerful vehicle for investigating knowledge and understandings, evolving new meaning and awakening latent creativity in the use of images for meaning making. This research informs the New Literacies and multimodal fields of enquiry and argues that visuality is integral to any pedagogy that purports to be relevant to the contemporary learner. It argues that the visual has been significantly under-valued as a conduit for knowledge acquisition and meaning making in the digital environment and supports the claim that critical literacy, interactivity, experimentation and production are vital to attaining the tenets of transformative education (Buckingham, 2007; Walsh, 2007; Cope & Kalantzis, 2008.

  10. Impact of TQM and Technology Management on Organizational Performance

    Directory of Open Access Journals (Sweden)

    MUHAMMAD TASLEEM

    2016-10-01

    Full Text Available In the growing business competitiveness TQM (Total Quality Management and TM (Technology Management practices have become important for organizational success. TQM fosters business excellence while TM helps to deal with process and product related technological challenges. However, in literature TM has received little consideration with TQM. This paper is a research study that attempts to identify any combined relationship of both concepts with OP (Organizational Performance while taking into account different organizational contextual factors including ISO-9001 certification. Responses from 86 different organizations in Pakistan are collected through questionnaire survey and random sampling. Statistical analysis shows that OP is positively associated to TQM and TM. Results of this study indicate the significance of ISO-9001 certification for TQM but do not support it for OP. It is also observed that organizations of private sector are significantly better in TQM and TM practices, so in OP, in comparison to government or public sector organizations. The study contributes to explore and augment both practices for implementation to improve OP.

  11. Review of PV Inverter Technology Cost and Performance Projections

    Energy Technology Data Exchange (ETDEWEB)

    Navigant Consulting Inc.

    2006-01-01

    The National Renewable Energy Laboratory (NREL) has a major responsibility in the implementation of the U.S. Department of Energy's (DOE's) Solar Energy Technologies Program. Sandia National Laboratories (SNL) has a major role in supporting inverter development, characterization, standards, certifications, and verifications. The Solar Energy Technologies Program recently published a Multiyear Technical Plan, which establishes a goal of reducing the Levelized Energy Cost (LEC) for photovoltaic (PV) systems to $0.06/kWh by 2020. The Multiyear Technical Plan estimates that, in order to meet the PV system goal, PV inverter prices will need to decline to $0.25-0.30 Wp by 2020. DOE determined the need to conduct a rigorous review of the PV Program's technical and economic targets, including the target set for PV inverters. NREL requested that Navigant Consulting Inc.(NCI) conduct a review of historical and projected cost and performance improvements for PV inverters, including identification of critical barriers identified and the approaches government might use to address them.

  12. Assessing the Role of Technology Adoption in China's Growth Performance

    DEFF Research Database (Denmark)

    Wirz, Nadja

    to what extent these productivity increases can be explained by technology-adoption theory. In less developed countries, the key element behind technological progress is technology adoption, the process of copying technological knowledge invented throughout the world. To uncover a measure of China...

  13. Development of evaluation and performance verification technology for radiotherapy radiation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J. Y.; Jang, S. Y.; Kim, B. H. and others

    2005-02-15

    No matter how much the importance is emphasized, the exact assessment of the absorbed doses administered to the patients to treat the various diseases such as lately soaring malignant tumors with the radiotherapy practices is the most important factor. In reality, several over-exposed patients from the radiotherapy practice become very serious social issues. Especially, the development of a technology to exactly assess the high doses and high energies (In general, dose administered to the patients with the radiotherapy practices are very huge doses, and they are about three times higher than the lethal doses) generated by the radiation generators and irradiation equipment is a competing issue to be promptly conducted. Over fifty medical centers in Korea operate the radiation generators and irradiation equipment for the radiotherapy practices. However, neither the legal and regulatory systems to implement a quality assurance program are sufficiently stipulated nor qualified personnel who could run a program to maintain the quality assurance and control of those generators and equipment for the radiotherapy practices in the medical facilities are sufficiently employed. To overcome the above deficiencies, a quality assurance program such as those developed in the technically advanced countries should be developed to exactly assess the doses administered to patients with the radiotherapy practices and develop the necessary procedures to maintain the continuing performance of the machine or equipment for the radiotherapy. The QA program and procedures should induce the fluent calibration of the machine or equipment with quality, and definitely establish the safety of patients in the radiotherapy practices. In this study, a methodology for the verification and evaluation of the radiotherapy doses is developed, and several accurate measurements, evaluations of the doses delivered to patients and verification of the performance of the therapy machine and equipment are

  14. Research about reactor operator's personability characteristics and performance

    Energy Technology Data Exchange (ETDEWEB)

    Wei Li; He Xuhong; Zhao Bingquan [Tsinghua Univ., Institute of Nuclear Energy Technology, Beijing (China)

    2003-03-01

    To predict and evaluate the reactor operator's performance by personality characteristics is an important part of reactor operator safety assessment. Using related psychological theory combined with the Chinese operator's fact and considering the effect of environmental factors to personality analysis, paper does the research about the about the relationships between reactor operator's performance and personality characteristics, and offers the reference for operator's selection, using and performance in the future. (author)

  15. Research progress of laser welding process dynamic monitoring technology based on plasma characteristics signal

    Directory of Open Access Journals (Sweden)

    Teng WANG

    2017-02-01

    Full Text Available During the high-power laser welding process, plasmas are induced by the evaporation of metal under laser radiation, which can affect the coupling of laser energy and the workpiece, and ultimately impact on the reliability of laser welding quality and process directly. The research of laser-induced plasma is a focus in high-power deep penetration welding field, which provides a promising research area for realizing the automation of welding process quality inspection. In recent years, the research of laser welding process dynamic monitoring technology based on plasma characteristics is mainly in two aspects, namely the research of plasma signal detection and the research of laser welding process modeling. The laser-induced plasma in the laser welding is introduced, and the related research of laser welding process dynamic monitoring technology based on plasma characteristics at home and abroad is analyzed. The current problems in the field are summarized, and the future development trend is put forward.

  16. High-Performance WSe2 Complementary Metal Oxide Semiconductor Technology and Integrated Circuits.

    Science.gov (United States)

    Yu, Lili; Zubair, Ahmad; Santos, Elton J G; Zhang, Xu; Lin, Yuxuan; Zhang, Yuhao; Palacios, Tomás

    2015-08-12

    Because of their extraordinary structural and electrical properties, two-dimensional materials are currently being pursued for applications such as thin-film transistors and integrated circuit. One of the main challenges that still needs to be overcome for these applications is the fabrication of air-stable transistors with industry-compatible complementary metal oxide semiconductor (CMOS) technology. In this work, we experimentally demonstrate a novel high performance air-stable WSe2 CMOS technology with almost ideal voltage transfer characteristic, full logic swing and high noise margin with different supply voltages. More importantly, the inverter shows large voltage gain (∼38) and small static power (picowatts), paving the way for low power electronic system in 2D materials.

  17. A high-performance trench capacitor integrated in a passive integration technology

    International Nuclear Information System (INIS)

    Geiselbrechtinger, Angelika; Büyüktas, Kevni; Allers, Karl-Heinz; Hartung, Wolfgang

    2009-01-01

    The requirements for the electrical characteristics of passive on-chip devices become more and more important. The electrical performance of RF circuits is predominantly restricted by the passives. New technologies and new device concepts are necessary to meet the demands. In this work, a trench capacitor developed for RF applications is presented for the first time. This so-called SilCap (silicon capacitor) device features very high capacitance density, extreme low-voltage dependence, excellent temperature stability, good RF performance and a high breakthrough voltage. First, the device function and the technological concept are introduced. The concept is realized without implementing cost-intensive high-k materials. This trench capacitor is integrated in the front end of line of a passive integration technology. The achieved specific capacitance density is compared to a standard planar capacitor. Performance of the SilCap in terms of quality factor and breakthrough voltage is shown. Finally, reliability data of this trench capacitor are presented with special focus on extrinsic and dielectric lifetime

  18. Study on transient hydrodynamic performance and cavitation characteristic of high-speed mixed-flow pump

    International Nuclear Information System (INIS)

    Chen, T; Liu, Y L; Sun, Y B; Wang, L Q; Wu, D Z

    2013-01-01

    In order to analyse the hydrodynamic performance and cavitation characteristic of a high-speed mixed-flow pump during transient operations, experimental studies were carried out. The transient hydrodynamic performance and cavitation characteristics of the mixed-flow pump with guide vane during start-up operation processes were tested on the pump performance test-bed. Performance tests of the pump were carried out under various inlet pressures and speed-changing operations. The real-time instantaneous external characteristics such as rotational speed, hydraulic head, flow rate, suction pressure and discharge pressure of the pump were measured. Based on the experimental results, the effect of fluid acceleration on the hydrodynamic performances and cavitation characteristics of the mixed-flow pump were analysed and evaluated

  19. South African exporter performance: new research into firm-specific and market characteristics

    Directory of Open Access Journals (Sweden)

    Christopher May

    2012-05-01

    Full Text Available The export marketing performance of any firm is influenced by a multitude of different factors. Given the multi-faceted nature of the export market, this research study investigated specific factors such as how firm-specific characteristics, product characteristics, market characteristics and export marketing strategies impact on the export marketing performance of South African manufacturing firms. Some of the findings of this research study indicated that firm size, investment commitment and careful planning, as firm-specific characteristics, had a significant influence on export marketing performance. The relationship between export experience and export marketing performance was insignificant. The degree of pricing adaptation and product adaptation had a significant effect on export marketing performance, while this was not the case with respect to the degree of promotion adaptation and distributor support.

  20. Research of influence of technological parameters on the noise characteristics of the machine for grinding meat

    Directory of Open Access Journals (Sweden)

    A. K. Pil’nenko

    2016-01-01

    Full Text Available Noise characteristics (NC machine is one of the main indicators of its quality and competitiveness on the world markets. Scientific and technical work to improve the noise characteristics are relevant and modern. Work focuses on the study of the emergence of the technological equipment of acoustic phenomena. Was selected method of determination and equipment, according to the international standards ISO “Acoustics” taking into account the acoustic properties of the surrounding space. Been established NC machines for grinding meat and fish under operating conditions the in various modes. The maximum value for the characteristic A sound power level (SPL machines produced at idling 79,7 dBA. When the machine comes with the product decline USM on the characteristics A 7.3 dB. It was found exceeding the maximum allowable sound power level at medium frequencies on 2 dB. Impact the components of machines on its NC depending on variables technological factors - the module of elasticity of the product and the effort on the pushrod. Increase modulus of elasticity SPL machines decreases and increase efforts on the pusher Machines USM increases. It was found negative impact construction machines part sat USM. Should be increased rigidity design of the machine.

  1. TECHNOLOGICAL DEVELOPMENT OF DRIVING SUPPORT SYSTEMS BASED ON HUMAN BEHAVIORAL CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    Shunichi DOI

    2006-01-01

    Full Text Available Driving support and cruise assist systems are of growing importance in achieving both road traffic safety and convenience. Such driver support seeks to achieve, with the highest possible quality, nothing less than “driver-vehicle symbiosis under all conditions.” At the same time, many traffic accidents result from improper driver behavior. The author focuses on driver behavior under various driving conditions, conducting detailed measurement and analysis of visual perception and attention characteristics as well as perceptual characteristics involved in driving. The aim in doing so is to support research on driving support systems and driving workload reduction technologies that function as human-vehicle systems and take such characteristics into account.

  2. The Influence of Top Management Team Characteristics on BPD Performance (P.155-166

    Directory of Open Access Journals (Sweden)

    Joy Elly Tulung

    2017-01-01

    Full Text Available Based on ”upper echelons theory”, this paper investigates the relation between top management team composition and BPD performance. For top management team characteristics, we employ age, level of education, background of education, gender, and functional background, while for measured the BPD performance we employ return on asset (ROA, return on equity (ROE, capital adequacy ratio (CAR, net interest margin (NIM, loan to deposit ratio (LDR, non-performing loan (NPL and operation expenses to operation income (BOPO. The results show that all characteristics have positive significant influences on BPD performance.Keywords: Top Management Team,BPD Performance, Upper Echelons Theory 

  3. Vaginal semisolid products: Technological performance considering physiologic parameters.

    Science.gov (United States)

    Machado, Rita Monteiro; Palmeira-de-Oliveira, Ana; Martinez-de-Oliveira, José; Palmeira-de-Oliveira, Rita

    2017-11-15

    Vaginal semisolid products are frequently used to treat vaginal infections and atrophy-related symptoms of menopause. Formulations composition and the methods for their characterization, especially those developed concerning the target epithelia, are key tools to predict in vivo results at early stages of product development. However, recent studies on this subject have been almost exclusively focused on anti-HIV preparations. The aim of this work consists on improving traditional characterization methods by using physiological parameters in order to construct predictive tools to characterize a new ideal vaginal semisolid formulation whatever target it may have. Ten vaginal antimicrobial and hormonal products already available in the market were studied (Gino-Canesten®, Sertopic®, Dermofix®, Gyno-pevaryl®, Lomexin®, Gino Travogen®, Dalacin V®, Ovestin®, Blissel®, Colpotrophine®). Furthermore, Universal Placebo gel and Replens® were used for comparison. Products were characterized in terms of: pH and buffering capacity in a vaginal fluid simulant (VFS); osmolality - directly and upon dilution in VFS; textural parameters (firmness, adhesiveness and bioadhesion) using vaginal ex vivo porcine epithelium; and viscosity (including VFS dilution at 37°C and after administration on an ex vivo model). Interestingly, the majority of the tested commercial vaginal formulations did not present technological characteristics close to the ideal ones when tested under target biological conditions. The inclusion of such methodologic adaptations is expected to optimize cost-efficiency of new formulations development by predicting efficacy and safety profiles at early stages of product development. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. High-Performance Secure Database Access Technologies for HEP Grids

    Energy Technology Data Exchange (ETDEWEB)

    Matthew Vranicar; John Weicher

    2006-04-17

    The Large Hadron Collider (LHC) at the CERN Laboratory will become the largest scientific instrument in the world when it starts operations in 2007. Large Scale Analysis Computer Systems (computational grids) are required to extract rare signals of new physics from petabytes of LHC detector data. In addition to file-based event data, LHC data processing applications require access to large amounts of data in relational databases: detector conditions, calibrations, etc. U.S. high energy physicists demand efficient performance of grid computing applications in LHC physics research where world-wide remote participation is vital to their success. To empower physicists with data-intensive analysis capabilities a whole hyperinfrastructure of distributed databases cross-cuts a multi-tier hierarchy of computational grids. The crosscutting allows separation of concerns across both the global environment of a federation of computational grids and the local environment of a physicist’s computer used for analysis. Very few efforts are on-going in the area of database and grid integration research. Most of these are outside of the U.S. and rely on traditional approaches to secure database access via an extraneous security layer separate from the database system core, preventing efficient data transfers. Our findings are shared by the Database Access and Integration Services Working Group of the Global Grid Forum, who states that "Research and development activities relating to the Grid have generally focused on applications where data is stored in files. However, in many scientific and commercial domains, database management systems have a central role in data storage, access, organization, authorization, etc, for numerous applications.” There is a clear opportunity for a technological breakthrough, requiring innovative steps to provide high-performance secure database access technologies for grid computing. We believe that an innovative database architecture where the

  5. High-Performance Secure Database Access Technologies for HEP Grids

    International Nuclear Information System (INIS)

    Vranicar, Matthew; Weicher, John

    2006-01-01

    The Large Hadron Collider (LHC) at the CERN Laboratory will become the largest scientific instrument in the world when it starts operations in 2007. Large Scale Analysis Computer Systems (computational grids) are required to extract rare signals of new physics from petabytes of LHC detector data. In addition to file-based event data, LHC data processing applications require access to large amounts of data in relational databases: detector conditions, calibrations, etc. U.S. high energy physicists demand efficient performance of grid computing applications in LHC physics research where world-wide remote participation is vital to their success. To empower physicists with data-intensive analysis capabilities a whole hyperinfrastructure of distributed databases cross-cuts a multi-tier hierarchy of computational grids. The crosscutting allows separation of concerns across both the global environment of a federation of computational grids and the local environment of a physicist's computer used for analysis. Very few efforts are on-going in the area of database and grid integration research. Most of these are outside of the U.S. and rely on traditional approaches to secure database access via an extraneous security layer separate from the database system core, preventing efficient data transfers. Our findings are shared by the Database Access and Integration Services Working Group of the Global Grid Forum, who states that 'Research and development activities relating to the Grid have generally focused on applications where data is stored in files. However, in many scientific and commercial domains, database management systems have a central role in data storage, access, organization, authorization, etc, for numerous applications'. There is a clear opportunity for a technological breakthrough, requiring innovative steps to provide high-performance secure database access technologies for grid computing. We believe that an innovative database architecture where the secure

  6. Operational characteristics, strategies and performance of foreign and demestic banks in India

    OpenAIRE

    Keshari, Pradeep Kumar

    2013-01-01

    This paper has tried to examine the relative characteristics and performance of foreign and domestic banks operating in India. A comparison of their characteristics undoubtedly suggest that foreign banks as a group differ significantly from domestic banks. It was also found that foreign banks enjoyed higher profitability than the domestic banks. The higher profitability of the former was a reflection of their particular operational characteristics, strategies and the favourable attitude of t...

  7. A numerical study on the flow and performance characteristics of a piezoelectric micropump with electromagnetic resistance for electrically conducting fluids

    International Nuclear Information System (INIS)

    An, Yong Jun; Choi, Chung Ryul; Kim, Chang Nyung

    2008-01-01

    A numerical analysis has been conducted for flow characteristics and performance of a micropump with piezodisk and MHD (MagnetoHydroDynamics) fluid. Various micro systems which could not be considered in the past have been recently growing with the development of MEMS (Micro Electro Mechanical System) and micro machining technology. Especially, micropumps, essential part of micro fluidic devices, are being lively studied by many researchers. In the present study, the piezo electric micropump with electromagnetic resistance for electrically conducting fluids is considered. The prescribed grid deformation method is used for the displacement of the membrane. The change of the performance of the micropump and flow characteristics of the electrically conducting fluid with the magnitude of the magnetic fields, duct size, the position of the inlet and outlet duct are investigated in the present study

  8. Reliability modeling of degradation of products with multiple performance characteristics based on gamma processes

    International Nuclear Information System (INIS)

    Pan Zhengqiang; Balakrishnan, Narayanaswamy

    2011-01-01

    Many highly reliable products usually have complex structure, with their reliability being evaluated by two or more performance characteristics. In certain physical situations, the degradation of these performance characteristics would be always positive and strictly increasing. In such a case, the gamma process is usually considered as a degradation process due to its independent and non-negative increments properties. In this paper, we suppose that a product has two dependent performance characteristics and that their degradation can be modeled by gamma processes. For such a bivariate degradation involving two performance characteristics, we propose to use a bivariate Birnbaum-Saunders distribution and its marginal distributions to approximate the reliability function. Inferential method for the corresponding model parameters is then developed. Finally, for an illustration of the proposed model and method, a numerical example about fatigue cracks is discussed and some computational results are presented.

  9. Relationship characteristics and performance in fresh produce supply chains: the case of the Mexican avocado industry

    NARCIS (Netherlands)

    Coronado, J.J.A.; Bijman, J.; Omta, S.W.F.; Oude Lansink, A.G.J.M.

    2010-01-01

    Abstract Inter-organisational relations research has shown that relationship characteristics can influence performance in seller-buyer transactions. Using a transaction cost economics approach, this research shows that relational elements such as expectation of continuity reduce the transaction

  10. Interactions Between Channel Topography and Hydrokinetic Turbines: Sediment Transport, Turbine Performance, and Wake Characteristics

    Science.gov (United States)

    Hill, Craig Steven

    Accelerating marine hydrokinetic (MHK) renewable energy development towards commercial viability requires investigating interactions between the engineered environment and its surrounding physical and biological environments. Complex and energetic hydrodynamic and morphodynamic environments desired for such energy conversion installations present difficulties for designing efficient yet robust sustainable devices, while permitting agency uncertainties regarding MHK device environmental interactions result in lengthy and costly processes prior to installing and demonstrating emerging technologies. A research program at St. Anthony Falls Laboratory (SAFL), University of Minnesota, utilized multi-scale physical experiments to study the interactions between axial-flow hydrokinetic turbines, turbulent open channel flow, sediment transport, turbulent turbine wakes, and complex hydro-morphodynamic processes in channels. Model axial-flow current-driven three-bladed turbines (rotor diameters, dT = 0.15m and 0.5m) were installed in open channel flumes with both erodible and non-erodible substrates. Device-induced local scour was monitored over several hydraulic conditions and material sizes. Synchronous velocity, bed elevation and turbine performance measurements provide an indication into the effect channel topography has on device performance. Complimentary experiments were performed in a realistic meandering outdoor research channel with active sediment transport to investigate device interactions with bedform migration and secondary turbulent flow patterns in asymmetric channel environments. The suite of experiments undertaken during this research program at SAFL in multiple channels with stationary and mobile substrates under a variety of turbine configurations provides an in-depth investigation into how axial-flow hydrokinetic devices respond to turbulent channel flow and topographic complexity, and how they impact local and far-field sediment transport characteristics

  11. COMPETENCY, ENTREPRENEUR CHARACTERISTIC AND BUSINESS PERFORMANCE: STUDY OF THE PEMPEK BUSINESS IN PALEMBANG

    Directory of Open Access Journals (Sweden)

    Fransiska Soejono

    2015-01-01

    Full Text Available The purpose of this study was to examine empirically the effects of entrepreneurial compe-tencies and characteristics on business performance. Previous studies found that competencies and entrepreneurial characteristics significantly influenced business performance. A quantita-tive method was used and 122 respondents were involved as the sample in this study, who were pempek business owners in Palembang, South Sumatra. The results indicated an effect from entrepreneurial competencies on business performance. It was also found that the entrepre-neurs’ characteristics (owners’ ages significantly affected the businesses’ performance. This implication requires some sort of course or program for the entrepreneurs to improve their competence to direct the owners to gain better business performance. The growing age of the business owners requires equal insights to ensure age does not stop the owners from improving their business’ performance.

  12. Evaluation of the dosimetric performance characteristic of fluoroscopy system used in medicine

    International Nuclear Information System (INIS)

    Qi Xuesong; Wei Kedao; Cheng Yuxi; Zhou Qifu; Ge Lijuan; Hou Changsong

    2001-01-01

    Objective: To discuss establishment of diagnostic reference dose value in fluoroscopic examinations for survey of 16 different types of fluoroscopy systems. Methods: Choosing dosimetric characteristic parameters including: IIESDR, ESDR (typical value) and ESDR max (ESDR maximum), and DAP, which was calibrated in situ on the X-ray unit. Results: Results of dose survey are summarized in three tables, from these we could get wide changes in accordance with those in many other countries resulting from maximum and minimum of IIESDR, ESDR and ESDRmax when measurements were performed at same entrance field size on I.I. Image Intensifier of the 15 fluoroscopy systems and under conditions of ABC. And also we could get less changes of DAP mean values, though differences for patient weight, technological parameters of fluoroscopic exam setting, fluoroscopic time and number of film were more remarkable. Conclusions: Measurements on IIESDR, ESDR (typical value) and ESDRmax (ESDR maximum) are not satisfied as diagnostic reference level. But it is suggested that DAP values, in fluoroscopic exam, are used as a tool to achieve this. (author)

  13. Microencapsulation by spray drying of Lannea microcarpa extract: Technological characteristics and antioxidant activity.

    Directory of Open Access Journals (Sweden)

    Francesca Sansone

    2014-08-01

    Full Text Available Context: A functional extract from Lannea microcarpa (Lm, possess interesting antioxidant and anti-inflammatory properties. However, the unprocessed dried extract occurs as sticky and low-water-soluble material showing critical properties for industrial applications. The unprocessed dried extract is not always enough stable to preserve its functional properties, also giving practical difficulties for the manufacturing. Aims: This research aimed to produce Lm extract microparticles with enhanced functional stability and technological characteristics by spray-drying. Methods: Lm extract was microencapsulated by spray-drying using a sodium-carboxymethylcellulose (NaCMC based matrix. Physicochemical and technological characteristics (determined by UV, HPLC, LLS, SEM, DSC, and in vitro dissolution tests, as well as antioxidant properties (DPPH-test of the resulting powder (LmC were examined. Results: The produced spray dried microparticles showed satisfying encapsulation efficiency, good functional stability and enhanced technological properties. The selected carrier and process conditions led to a stable and handling microencapsulated powder form with improved water dissolution rate. Moreover, the matrix was also able to preserve the antioxidant activity of the phenolic compounds-rich extract. Conclusions: The made-up powder resulted in a functional component that can be used with great potential in cosmetics, foods or nutraceutical products.

  14. Effect of Cattle Breeds on Milk Composition and Technological Characteristics in China

    Directory of Open Access Journals (Sweden)

    T. X. Yang

    2013-06-01

    Full Text Available Cattle breeds have a striking effect on milk, including milk composition and technological characteristics. This study aims to compare milk composition, acidification activity, viscosity, milk dispersion system stability and casein molecular weight among three buffalo breeds in China. The technological characteristics of milk produced by three cattle breeds of river buffalo (Murrah, crossbreed 1st generation (F1, crossbreed multiple generation (FH, H≥3 buffaloes were investigated. Cattle breeds showed evident effect on milk protein, fat and total solids content, but little effect on most of buffalo casein molecular weight. Milk fat, protein content and the viscosity of buffalo milk from river buffalo were lower than those of F1 and FH, so was the buffer capacity. The viscosity was negatively correlated to temperature and concentration. Results of stability coefficient showed that milk dispersion system had the best dynamic stability characteristics under pH 6.6 and 6 times dilution, while zeta potential of Murrah milk was slightly higher than that of hybrid offspring (F1, FH. SDS-PAGE results showed that buffalo αs-casein had a slightly faster mobility than standard αs-casein; while buffalo β-casein showed a slightly slower mobility than standard β-casein. There is no clear differences in molecular weight of αs-, β-, and κ-casein among Murrah, F1 and FH.

  15. How Partner Characteristics Can Affect Performance of Alliances with Different Time Frames?

    Directory of Open Access Journals (Sweden)

    Seyed Hossein JALALI

    2017-11-01

    Full Text Available Firms increasingly adopt cooperative strategies and form strategic alliances with foreign partners to be prosperous in entering to international market. Most of scholars have typically focused on generic, conceptual models for alliances partner selection, addressing only limited dimensions of the partner characteristics. This paper presents a new empirical framework that considering the effect of partner characteristics on export performance of alliances, in the case of short/mediumterm alliances and long-term ones. The study explores the effective partner characteristics for each type of alliances based on a sample of 540 alliances which rooted in East European region and also, have at least one Iranian partner. The findings stress the differences between varied partner characteristics in short/medium-term and long-term alliances. More specifically, results introduce a framework that addresses certain and specific partner characteristics to improve the export performance of alliances, due to the time frame of strategic alliances.

  16. Psychosocial Characteristics of Optimum Performance in Isolated and Confined Environments (ICE)

    Science.gov (United States)

    Palinkas, Lawrence A.; Keeton, Kathryn E.; Shea, Camille; Leveton, Lauren B.

    2010-01-01

    The Behavioral Health and Performance (BHP) Element addresses human health risks in the NASA Human Research Program (HRP), including the Risk of Adverse Behavioral Conditions and the Risk of Psychiatric Disorders. BHP supports and conducts research to help characteristics and mitigate the Behavioral Medicine risk for exploration missions, and in some instances, current Flight Medical Operations. The Behavioral Health and Performance (BHP) Element identified research gaps within the Behavioral Medicine Risk, including Gap BMed6: What psychosocial characteristics predict success in an isolated, confined environment (ICE)? To address this gap, we conducted an extensive and exhaustive literature review to identify the following: 1) psychosocial characteristics that predict success in ICE environments; 2) characteristics that are most malleable; and 3) specific countermeasures that could enhance malleable characteristics.

  17. Standard guide for evaluating performance characteristics of phased-Array ultrasonic testing instruments and systems

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This guide describes procedures for evaluating some performance characteristics of phased-array ultrasonic examination instruments and systems. 1.2 Evaluation of these characteristics is intended to be used for comparing instruments and systems or, by periodic repetition, for detecting long-term changes in the characteristics of a given instrument or system that may be indicative of impending failure, and which, if beyond certain limits, will require corrective maintenance. Instrument characteristics measured in accordance with this guide are expressed in terms that relate to their potential usefulness for ultrasonic examinations. Other electronic instrument characteristics in phased-array units are similar to non-phased-array units and may be measured as described in E 1065 or E 1324. 1.3 Ultrasonic examination systems using pulsed-wave trains and A-scan presentation (rf or video) may be evaluated. 1.4 This guide establishes no performance limits for examination systems; if such acceptance criteria ar...

  18. Post Advanced Technology Implementation Effects on School Psychologist Job Performance

    Science.gov (United States)

    Hobson, Rana Dirice

    2017-01-01

    The technology acceptance model (TAM) has been widely used to assess technology adoption in business, education, and health care. The New York City Department of Education (NYCDOE) launched a web-based Individualized Educational Program (IEP) system for school psychologists to use in conducting evaluations and reviews. This quantitative study…

  19. Technology Performance Report: Duke Energy Notrees Wind Storage Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Wehner, Jeff [Duke Energy Renewables, Charlotte, NC (United States); Mohler, David [Duke Energy Renewables, Charlotte, NC (United States); Gibson, Stuart [Duke Energy Renewables, Charlotte, NC (United States); Clanin, Jason [Duke Energy Renewables, Charlotte, NC (United States); Faris, Don [Duke Energy Renewables, Charlotte, NC (United States); Hooker, Kevin [Duke Energy Renewables, Charlotte, NC (United States); Rowand, Michael [Duke Energy Renewables, Charlotte, NC (United States)

    2015-11-01

    Duke Energy Renewables owns and operates the Notrees Wind Farm in west Texas’s Ector and Winkler counties. The wind farm, which was commissioned in April 2009, has a total capacity of 152.6 MW generated by 55 Vestas V82 turbines, one Vestas 1-V90 experimental turbine, and 40 GE 1.5-MW turbines. The Vestas V82 turbines have a generating capacity of 1.65 MW each, the Vestas V90 turbine has a generating capacity of 1.86 MW, and the GE turbines have a generating capacity of 1.5 MW each. The objective of the Notrees Wind Storage Demonstration Project is to validate that energy storage increases the value and practical application of intermittent wind generation and is commercially viable at utility scale. The project incorporates both new and existing technologies and techniques to evaluate the performance and potential of wind energy storage. In addition, it could serve as a model for others to adopt and replicate. Wind power resources are expected to play a significant part in reducing greenhouse gas emissions from electric power generation by 2030. However, the large variability and intermittent nature of wind presents a barrier to integrating it within electric markets, particularly when competing against conventional generation that is more reliable. In addition, wind power production often peaks at night or other times when demand and electricity prices are lowest. Energy storage systems can overcome those barriers and enable wind to become a valuable asset and equal competitor to conventional fossil fuel generation.

  20. Geological and technological characteristics of the Ball Clay of the Sao Paulo state

    International Nuclear Information System (INIS)

    Tanno, L.C.; Motta, J.F.M.; Cabral Junior, M.; Saka, S.; Souza, D.D.D.

    1990-01-01

    This paper shows preliminary geological and technological results of studies about ball clay in Sao Paulo State. The works had been carried out by the Institute of Research and technology (IPT) and sponsored by Prominerio, during 88. Ball clay is a special clay utilised in the whiteware industry, mainly in the body preparation of sanitaryware products. This raw material come from two sites in Brazil: Sao Simao and Oeiras. Samples from these two deposits had been studied and classified acording to their adequately in the ceramic process. On the other hand, more than 100 samples from several geological sites of the Sao Paulo State were studied in laboratories. Acording to preliminary tests some of them revealed similar characteristics as brazilian ball clays. These clays were characterized by granulometry analysis, X-ray diffraction and chemical analysis. (author) [pt

  1. Regional characteristics of individual housing units in Serbia from the aspect of applied building technologies

    Directory of Open Access Journals (Sweden)

    Jovanović-Popović Milica

    2014-01-01

    Full Text Available Individual housing units in Serbia have been studied from the aspect of applied technical solutions. Analyzed data have been collected during a field research in accordance with the current administrative regional division, and they represent a basis for definition of regional typology of individual housing units. Characteristic types of objects of each region’s typology have been further analyzed. Upon these analyses regional characteristics of individual housing units regarding applied construction types, building technologies and materials have been defined and presented. [Projekat Ministarstva nauke Republike Srbije, br. TR 36034: Investigation and Systematization of Serbian Housing in Context of Globalization and European Integration in the Framework of Quality and Living-Standard Improvement

  2. Improved Switching Characteristics of Fast Power MOSFETs Applying Solder Bump Technology

    Directory of Open Access Journals (Sweden)

    Sibylle Dieckerhoff

    2008-01-01

    Full Text Available The impact of a reduced package stray inductance on the switching performance of fast power MOSFETs is discussed applying advanced 3D packaging technologies. Starting from an overview over new packaging approaches, a solder bump technology using a flexible PI substrate is exemplarily chosen for the evaluation. Measurement techniques to determine the stray inductance are discussed and compared with a numerical solution based on the PEEC method. Experimental results show the improvement of the voltage utilization while there is only a slight impact on total switching losses.

  3. Technology transfer from biomedical research to clinical practice: measuring innovation performance.

    Science.gov (United States)

    Balas, E Andrew; Elkin, Peter L

    2013-12-01

    Studies documented 17 years of transfer time from clinical trials to practice of care. Launched in 2002, the National Institutes of Health (NIH) translational research initiative needs to develop metrics for impact assessment. A recent White House report highlighted that research and development productivity is declining as a result of increased research spending while the new drugs output is flat. The goal of this study was to develop an expanded model of research-based innovation and performance thresholds of transfer from research to practice. Models for transfer of research to practice have been collected and reviewed. Subsequently, innovation pathways have been specified based on common characteristics. An integrated, intellectual property transfer model is described. The central but often disregarded role of research innovation disclosure is highlighted. Measures of research transfer and milestones of progress have been identified based on the Association of University Technology Managers 2012 performance reports. Numeric milestones of technology transfer are recommended at threshold (top 50%), target (top 25%), and stretch goal (top 10%) performance levels. Transfer measures and corresponding target levels include research spending to disclosure (0.81), patents to start-up (>0.1), patents to licenses (>2.25), and average per license income (>$48,000). Several limitations of measurement are described. Academic institutions should take strategic steps to bring innovation to the center of scholarly discussions. Research on research, particularly on pathways to disclosures, is needed to improve R&D productivity. Researchers should be informed about the technology transfer performance of their institution and regulations should better support innovators.

  4. Characteristics modeling for supercritical circulating fluidized bed boiler working in oxy-combustion technology

    Directory of Open Access Journals (Sweden)

    Balicki Adrian

    2014-06-01

    Full Text Available Among the technologies which allow to reduce greenhouse gas emission, mainly carbon dioxide, special attention deserves the idea of ‘zeroemission’ technology based on boilers working in oxy-combustion technology. In the paper the results of analyses of the influence of changing two quantities, namely oxygen share in oxidant produced in the air separation unit, and oxygen share in oxidant supplied to the furnace chamber on the selected characteristics of a steam boiler including the degree of exhaust gas recirculation, boiler efficiency and adiabatic flame temperature, was examined. Due to the possibility of the integration of boiler model with carbon dioxide capture, separation and storage installation, the subject of the analysis was also to determine composition of the flue gas at the outlet of a moisture condensation installation. Required calculations were made using a model of a supercritical circulating fluidized bed boiler working in oxy-combustion technology, which was built in a commercial software and in-house codes.

  5. [Genetic improvement of technological characteristics of starters for fermented milk products].

    Science.gov (United States)

    Oganesian, G G; Barsegian, A A; Grigorian, N G; Toptsian, A V

    2010-01-01

    Possibility for improvement of technological characteristics of lactobacilli using mutations of resistance to rifampicin (rif(r)) and streptomycin (str(r)) was studied. Using starter model of Narine Lactobacillus acidophilus INMIA-9602 Armenian diet milk product, it was showed that a possibility for selecting strains with increased rate of milk fermentation and acid production is higher in Rif(r) and Str(r) mutants induced by nitrosoguanidine than in cultures sensitive to antibiotics. The milk products obtained using Rif(r) and Str(r) strains had high viscosity, improved texture, increased amount of alive cells and good organoleptic features.

  6. ORGANISATIONAL-TECHNOLOGICAL CHARACTERISTICS OF BLASTING WORKS ON THE GRIČ TUNNEL

    Directory of Open Access Journals (Sweden)

    Zvonimir Deković

    2005-12-01

    Full Text Available The paper describes organisational-technological characteristics of blasting works during the excavation of the Grič Tunnel. The significance of blasting works during the excavation of the tunnel is shown through adjustment of blasting parameters taking into consideration the dynamics of the works, cost-effectiveness and influence of geological circumstances. Successfulness of blasting directly influences the subsequent tunnel excavation cycle both in terms of duration as well as eventually in terms of influence on the entire tunnel investment. Comparison of changes of basic blasting parameters during tunnel excavation ensured optimal excavation progress with minimal price per meter of tunnel progress.

  7. CSR organisational taxonomy and job characteristics on performance: SME case studies

    Directory of Open Access Journals (Sweden)

    Thanalechumy Seeramulu

    2017-05-01

    Full Text Available This study examines the relationship between the CSR of organizational structure and job characteristics that influence employee job performance in the Malaysian context. Hence, it is important to study and analyze these two factors within the CSR taxonomy describing how these factors significantly influence employee job performance and to make recommendations how performance can be promoted among employees. This paper is based on a quantitative research approach where responses were gathered from the working population within Malaysia SMEs. The results from this study will help to point out the influence of these factors on the employee job performance and provide guidance to an organization for which these aspects should be emphasized in order to increase employees’ job performance to align performance with organizational goals. The analysis includes two dimensions of CSR taxonomy of organizational structure namely, centralization and formalization, as well as a set of five dimensions of job characteristics, such as task identity, task significance, skill variety, autonomy and feedback. The results of these findings show that job characteristics such as task significance, autonomy, feedback, and skill variety, positively influence job performance with autonomy having highest predictive power on job performance. The results of these findings reveal that the organizational structure does not contribute to the prediction of job performance even though a significant positive correlation exists between the structure and job performance in the Pearson correlation coefficient test. Therefore, this study will enrich the existing knowledge in the area of human resource management by focusing on job performance management.

  8. Perceptions of Value: A Study of Worker Characteristics and Performance Interventions

    Science.gov (United States)

    Welch, Corey M.

    2013-01-01

    This study addressed the need of human performance technology (HPT) practitioners to make the most cost-effective performance intervention decisions, introducing a new instrument, the Intervention Value Survey, as a possible tool to provide a clearer profile of an audience's perceptions of what provides them value. Using a mixed methods…

  9. The effect of individual characteristics of decision making and judgment on stock-flow performance

    NARCIS (Netherlands)

    Raaijmakers, S.; Korzilius, H.P.L.M.; Rouwette, E.A.J.A.; Vennix, J.A.M.

    2012-01-01

    Extending the line of research on stock-flow performance we examined the impact of personality characteristics on task performance. It was assumed that the need for cognition, the need for closure and the preference for intuition and deliberation would relate to individual variations in

  10. Personality Characteristics and Level of Performance of Male County Extension Agents in Wisconsin.

    Science.gov (United States)

    Pandya, Dasharathrai Navnitrai

    The major purpose of this study was to determine the relationship between selected personality characteristics and attitudes of male extension agents in Wisconsin, and their level of job performance. The relationships between selected background factors and the level of agent's job performance were also studied. Subjects were 79 male county agents…

  11. Supervisors' Performance Ratings Correlated with Selected Personal Characteristics of Attendants in a Mental Retardation Developmental Center.

    Science.gov (United States)

    Frederick, Joseph; And Others

    A research study investigated the relationship between personal characteristics and selected demographic data of 75 attendants in a mental retardation developmental center and the assessment by 24 administrators of the attendants' job performance. Instruments used included a 20-item Direct Care Performance Scale and the Demographic Data Scale,…

  12. Do firm characteristics influence mutual fund performance? An empirical study for European mutual funds

    NARCIS (Netherlands)

    de Jong, F.C.J.M.; Wingens, L.

    2013-01-01

    This study investigates the influence of fund management firm characteristics on mutual fund performance. Using a sample of European domiciled open-end equity funds for the period 1998-2008, this study finds that the funds of private companies have performed better than the funds of public

  13. 78 FR 15112 - Rulemaking Advisory Committee; Transport Airplane Performance and Handling Characteristics-New Task

    Science.gov (United States)

    2013-03-08

    ... Committee; Transport Airplane Performance and Handling Characteristics--New Task AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of new task assignment for the Aviation Rulemaking Advisory Committee... findings. The Task The FAA tasked ARAC to consider several areas within the airplane performance and...

  14. Students' Demographic, Academic Characteristics and Performance in Registered General Nursing Licensing Examination in Ghana

    Science.gov (United States)

    Doe, Patience Fakornam; Oppong, Elizabeth Agyeiwaa; Sarfo, Jacob Owusu

    2018-01-01

    The decreasing performance of student nurses in the professional licensure examinations (LE) in Ghana is a major concern to stakeholders, especially at a time when the nurse-patient ratio stands at 1: 1500. The study sought to determine the effect of students' demographic and academic characteristics on performance in the Registered General…

  15. High-performance-vehicle technology. [fighter aircraft propulsion

    Science.gov (United States)

    Povinelli, L. A.

    1979-01-01

    Propulsion needs of high performance military aircraft are discussed. Inlet performance, nozzle performance and cooling, and afterburner performance are covered. It is concluded that nonaxisymmetric nozzles provide cleaner external lines and enhanced maneuverability, but the internal flows are more complex. Swirl afterburners show promise for enhanced performance in the high altitude, low Mach number region.

  16. Charge initiation schemes for ensuring high-performance operation of cyclic-flow technology cyclic link

    Directory of Open Access Journals (Sweden)

    S. N. Zharikov

    2017-09-01

    Full Text Available The authors consider the issue of ensuring the quality of crushing rock mass by drilling and blasting method for high productivity of a cyclic link of a cyclic-flow technology complex. The article contains recommendations for calculating certain parameters of drilling and blasting operations, such as the width of the retaining wall Bp. s, the collapse with account for the retaining wall Вr, the width of the collapse of the rock mass Bf when blasting onto a free surface (for the first row of vertical wells and for the first series of inclined wells, the width of the collapse from the first series of wells B1, the deceleration time τ, the coefficient kβ that takes into account the incline angle of wells β to the horizon. The authors prove the expediency of using a retaining wall in explosions of technological blocks. The authors raise the question about the management of detonation characteristics of explosives produced in the field of application for the most rational impact of an explosion on a rock massif. Since the technological schemes for preparing the rock mass to the excavation, which ensure the high-performance operation of the cyclic link of the cyclic-flow technology, can be different, then the choice of a specific drilling and blasting circuit is depends on the geological conditions and elements of the development system. As a preliminary method of breaking, one can consider the explosion of charges along the diagonal (diagonal blasting schemes on the retaining wall. This method provides sufficient reliability of technological explosions, and with the development of modern means of blasting with decelerations between charges of more than 67 ms, there are nearly no back emissions.

  17. Towards a Tool for Assessing Supply-Chain Information Performance During Implementation of New Information Technologies

    NARCIS (Netherlands)

    Denolf, J.M.; Wognum, P.M.; Trienekens, J.H.; Vorst, van der J.G.A.J.; Omta, S.W.F.

    2012-01-01

    Based on improved information performance, agro-food companies and supply chains want to enhance their production processes. It creates the necessity to implement additional information technologies. The implementation of information technologies is, however, a complex task because of the

  18. A Performance-Based Technology Assessment Methodology to Support DoD Acquisition

    National Research Council Canada - National Science Library

    Mahafza, Sherry; Componation, Paul; Tippett, Donald

    2005-01-01

    .... This methodology is referred to as Technology Performance Risk Index (TPRI). The TPRI can track technology readiness through a life cycle, or it can be used at a specific time to support a particular system milestone decision...

  19. A Study of the Associations between Conditions of Performance and Characteristics of Performers and New York State Solo Performance Ratings

    Science.gov (United States)

    vonWurmb, Elizabeth C.

    2013-01-01

    This dissertation undertakes an analysis of 1,044 performance evaluations from New York State School Music Association (NYSSMA) Spring Festival solo adjudication ratings of student performers from a large suburban school district. It relies on results of evaluations of observed performances, and takes these evaluations as assessments of what the…

  20. Construction Professionals Job Performance and Characteristics: A Comparison of Indigenous and Expatriate Construction Companies in Nigeria

    Directory of Open Access Journals (Sweden)

    Henry Ndubuisi Onukwube

    2011-06-01

    Job performance is considered one of the most important constructs in human resources management because it helps to explain the value and utility that each employee adds to the organisation. The professionals in the Nigerian construction companies are not exception to the perceived low job performance rate within the industry. Extant literature points to the fact that job characteristics of employees can account for variance in their job performance rate.This study compares the job performance rate and job characteristics of construction professionals in indigenous and expatriate construction companies with a view to establish a relationship between job performance and job characteristics of construction professionals. A total of 762 questionnaires were collected and used for the study.  Eighty one (81 construction companies, 50 (62% indigenous and 31 (38% expatriate were selected using stratified random sampling technique. Data collected were analysed using mean item score, spearman rank correlation, linear regression analysis where appropriate. Findings of the study revealed that the relationship between job characteristics and job performance of construction professionals in construction companies in Nigeria is positive but low and the correlation coefficient is higher in expatriate construction companies. Based on the above finding, the study recommends that construction companies in Nigeria should endeavour and improve on their current core job dimensions (task significance, skill variety, task identity, autonomy and feedback inherent in various jobs designed within their respective organizations as this will constitute as one of the variants that will improve the job performance rate of construction professionals.

  1. Characteristics of Adults Seeking Health Care Provider Support Facilitated by Mobile Technology: Secondary Data Analysis.

    Science.gov (United States)

    Bosak, Kelly; Park, Shin Hye

    2017-12-21

    Mobile health technology is rapidly evolving with the potential to transform health care. Self-management of health facilitated by mobile technology can maximize long-term health trajectories of adults. Little is known about the characteristics of adults seeking Web-based support from health care providers facilitated by mobile technology. This study aimed to examine the following: (1) the characteristics of adults who seek human support from health care providers for health concerns using mobile technology rather than from family members and friends or others with similar health conditions and (2) the use of mobile health technology among adults with chronic health conditions. Findings of this study were interpreted in the context of the Efficiency Model of Support. We first described characteristics of adults seeking Web-based support from health care providers. Using chi-square tests for categorical variables and t test for the continuous variable of age, we compared adults seeking Web-based and conventional support by demographics. The primary aim was analyzed using multivariate logistic regression to examine whether chronic health conditions and demographic factors (eg, sex, income, employment status, race, ethnicity, education, and age) were associated with seeking Web-based support from health care providers. The sample included adults (N=1453), the majority of whom were female 57.60% (837/1453), white 75.02% (1090/1453), and non-Hispanic 89.13% (1295/1453). The age of the participants ranged from 18 to 92 years (mean 48.6, standard deviation [SD] 16.8). The majority 76.05% (1105/1453) of participants reported college or higher level of education. A disparity was found in access to health care providers via mobile technology based on socioeconomic status. Adults with annual income of US $30,000 to US $100,000 were 1.72 times more likely to use Web-based methods to contact a health care provider, and adults with an annual income above US $100,000 were 2.41 to

  2. Satisfaction with Online Commercial Group Chat: The Influence of Perceived Technology Attributes, Chat Group Characteristics, and Advisor Communication Style

    NARCIS (Netherlands)

    van Dolen, W.M.; Dabholkar, P.A.; de Ruyter, J.C.

    2007-01-01

    This study examines online commercial group chat from a structuration theory perspective. The findings support the influence of perceived technology attributes (control, enjoyment, reliability, speed, and ease of use) and chat group characteristics (group involvement, similarity, and receptivity) on

  3. Quantifying characteristics of information-technology applications based on expert knowledge for detection of oestrus and mastitis in dairy cows.

    Science.gov (United States)

    van Asseldonk, M A; Huirne, R B; Dijkhuizen, A A

    1998-10-09

    Expert opinions were elicited about the characteristics at the commercial-farm level of on-line information technology (IT) applications that are able to detect oestrus and mastitis in dairy cows. Since actual data of these characteristics are not available, judgmental data provided an alternative means to interpret the implications of research results for commercial farms. Applications included were activity measurement, milk-production measurement, electrical conductivity of quarter milk, automated concentrate feeders and milk-temperature measurement. Sensitivity and specificity of detection of oestrus (OD), clinical-mastitis (CMD) and subclinical-mastitis (SCMD) were ascertained. Conjoint-analysis was used to assess the effect of each application indirectly by decomposing the evaluated overall detection characteristics of a predefined number of IT combinations. The individual experts were consistent in evaluating the alternatives, but there was variation in estimates among experts. Estimations of the main effects of the applications and important first-order interactions were incorporated into the detection models. Implementation of all applications under study resulted in overall sensitivities and specificities of 82% and 90%, 73% and 87%, 58% and 82% for OD, CMD and SCMD, respectively. Further research is necessary that should take into account costs and benefits of the different detection systems based on the current status of farm performance (e.g. OD and mastitis incidence) and farm structure (e.g. farm size, years in operation of the milking parlour and parlour layout). Research to do this is currently in progress.

  4. Transmission Technologies and Operational Characteristic Analysis of Hybrid UHV AC/DC Power Grids in China

    Science.gov (United States)

    Tian, Zhang; Yanfeng, Gong

    2017-05-01

    In order to solve the contradiction between demand and distribution range of primary energy resource, Ultra High Voltage (UHV) power grids should be developed rapidly to meet development of energy bases and accessing of large-scale renewable energy. This paper reviewed the latest research processes of AC/DC transmission technologies, summarized the characteristics of AC/DC power grids, concluded that China’s power grids certainly enter a new period of large -scale hybrid UHV AC/DC power grids and characteristics of “strong DC and weak AC” becomes increasingly pro minent; possible problems in operation of AC/DC power grids was discussed, and interaction or effect between AC/DC power grids was made an intensive study of; according to above problems in operation of power grids, preliminary scheme is summarized as fo llows: strengthening backbone structures, enhancing AC/DC transmission technologies, promoting protection measures of clean energ y accessing grids, and taking actions to solve stability problems of voltage and frequency etc. It’s valuable for making hybrid UHV AC/DC power grids adapt to operating mode of large power grids, thus guaranteeing security and stability of power system.

  5. Pecan Street Grid Demonstration Program. Final technology performance report

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2015-02-10

    This document represents the final Regional Demonstration Project Technical Performance Report (TPR) for Pecan Street Inc.’s (Pecan Street) Smart Grid Demonstration Program, DE-OE-0000219. Pecan Street is a 501(c)(3) smart grid/clean energy research and development organization headquartered at The University of Texas at Austin (UT). Pecan Street worked in collaboration with Austin Energy, UT, Environmental Defense Fund (EDF), the City of Austin, the Austin Chamber of Commerce and selected consultants, contractors, and vendors to take a more detailed look at the energy load of residential and small commercial properties while the power industry is undergoing modernization. The Pecan Street Smart Grid Demonstration Program signed-up over 1,000 participants who are sharing their home or businesses’s electricity consumption data with the project via green button protocols, smart meters, and/or a home energy monitoring system (HEMS). Pecan Street completed the installation of HEMS in 750 homes and 25 commercial properties. The program provided incentives to increase the installed base of roof-top solar photovoltaic (PV) systems, plug-in electric vehicles with Level 2 charging, and smart appliances. Over 200 participants within a one square mile area took advantage of Austin Energy and Pecan Street’s joint PV incentive program and installed roof-top PV as part of this project. Of these homes, 69 purchased or leased an electric vehicle through Pecan Street’s PV rebate program and received a Level 2 charger from Pecan Street. Pecan Street studied the impacts of these technologies along with a variety of consumer behavior interventions, including pricing models, real-time feedback on energy use, incentive programs, and messaging, as well as the corresponding impacts on Austin Energy’s distribution assets.The primary demonstration site was the Mueller community in Austin, Texas. The Mueller development, located less than three miles from the Texas State Capitol

  6. Parametric study of geohydrologic performance characteristics for nuclear-waste repositories

    International Nuclear Information System (INIS)

    Bailey, C.E.; Marine, I.W.

    1981-01-01

    Purpose of this study was to present geohydrologic information in graphical form covering a wide range of parameters to aid in determining site specifications based on functional criteria. Graphs of the major performance characteristics that influence the transport of radionuclides from a repository to the biosphere by groundwater were developed. The major characteristics addressed are radioactive decay, leach rate, hydraulic conductivity, porosity, groundwater gradient, hydrodynamic dispersion, ion exchange, and distance to the biosphere

  7. Biomass Gasification. The characteristics of technology development and the rate of learning

    Energy Technology Data Exchange (ETDEWEB)

    Dorca Duch, Andreu; Huertas Bermejo, Javier

    2008-09-15

    . In the case of large scale, interest has shifted from electricity generation to biofuel production, primarily due to the failed demonstration projects of the technology coupled with combined cycle for electricity generation. On the other hand, in small scale projects, cogeneration applications have gained interest over heat production. However, there are fewer actors involved in small scale experimentation than in large scale. Once the specific situation of each country has been analyzed, and the main characteristics of the development process have been identified, one of the causes which have hindered the technology to reach the expected commercial stage has been the lack of resources to demonstrate its competitiveness. So far, a significant number of experimentation activities, based on demonstration projects and pilot plants, have proved the future potential of the technology. Nonetheless, the uncertainty, shown by the great majority of actors, about integrating the biomass gasification in their industrial process has hindered the demonstration of its operational feasibility. Following this, further efforts should focus on the creation of incentives for the construction of new plants which integrate this technology in an industrial process already consolidated in the market. An approximation of the number of new plants needed, could be a good indicator of the economical resources required in order to acquire enough experience to make biomass gasification a competitive technology in the short-term. After simulating various future evolutions for small scale cogeneration applications, the learning rate obtained through the learning curves model predict that, building roughly forty plants in six years, the technology can be consolidated firmly in the market. Considering the decrease in the number of new plants built since 2002, the expectancies are not really optimistic. Nevertheless, it is not an unachievable objective if incentives are created by all administrative

  8. Virtual street-crossing performance in persons with multiple sclerosis: Feasibility and task performance characteristics.

    Science.gov (United States)

    Stratton, M E; Pilutti, L A; Crowell, J A; Kaczmarski, H; Motl, R W

    2017-01-02

    Multiple sclerosis (MS) is a neurological disease that commonly results in physical and cognitive dysfunction. Accordingly, MS might impact the ability to safely cross the street. The purpose of this study was to examine the feasibility of a simulated street-crossing task in persons with MS and to determine differences in street-crossing performance between persons with MS and non-MS controls. 26 participants with MS (median Expanded Disability Status Scale [EDSS] score = 3.5) and 19 controls completed 40 trials of a virtual street-crossing task. There were 2 crossing conditions (i.e., no distraction and phone conversation), and participants performed 20 trials per condition. Participants were instructed that the goal of the task was to cross the street successfully (i.e., without being hit be a vehicle). The primary outcome was task feasibility, assessed as completion and adverse events. Secondary outcomes were measures of street-crossing performance. Overall, the simulated street-crossing task was feasible (i.e., 90% completion, no adverse events) in participants with MS. Participants with MS waited longer and were less attentive to traffic before entering the street compared with controls (all P .05). A virtual street-crossing task is feasible for studying street-crossing behavior in persons with mild MS and most individuals with moderate MS. Virtual street-crossing performance is impaired in persons with MS compared to controls; however, persons with MS do not appear to be more vulnerable to a distracting condition. The virtual reality environment presents a safe and useful setting for understanding pedestrian behavior in persons with MS.

  9. Technological parameters influence on the non-autoclaved foam concrete characteristics

    Science.gov (United States)

    Bartenjeva, Ekaterina; Mashkin, Nikolay

    2017-01-01

    Foam concretes are used as effective heat-insulating materials. The porous structure of foam concrete provides good insulating and strength properties that make them possible to be used as heat-insulating structural materials. Optimal structure of non-autoclaved foam concrete depends on both technological factors and properties of technical foam. In this connection, the possibility to manufacture heat-insulation structural foam concrete on a high-speed cavity plant with the usage of protein and synthetic foamers was estimated. This experiment was carried out using mathematical planning method, and in this case mathematical models were developed that demonstrated the dependence of operating performance of foam concrete on foaming and rotation speed of laboratory plant. The following material properties were selected for the investigation: average density, compressive strength, bending strength and thermal conductivity. The influence of laboratory equipment technological parameters on technical foam strength and foam stability coefficient in the cement paste was investigated, physical and mechanical properties of non-autoclaved foam concrete were defined based on investigated foam. As a result of investigation, foam concrete samples were developed with performance parameters ensuring their use in production. The mathematical data gathered demonstrated the dependence of foam concrete performance on the technological regime.

  10. Structured Innovation of High-Performance Wave Energy Converter Technology: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Weber, Jochem W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Laird, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-01-25

    Wave energy converter (WEC) technology development has not yet delivered the desired commercial maturity nor, and more importantly, the techno-economic performance. The reasons for this have been recognized and fundamental requirements for successful WEC technology development have been identified. This paper describes a multi-year project pursued in collaboration by the National Renewable Energy Laboratory and Sandia National Laboratories to innovate and develop new WEC technology. It specifies the project strategy, shows how this differs from the state-of-the-art approach and presents some early project results. Based on the specification of fundamental functional requirements of WEC technology, structured innovation and systemic problem solving methodologies are applied to invent and identify new WEC technology concepts. Using Technology Performance Levels (TPL) as an assessment metric of the techno-economic performance potential, high performance technology concepts are identified and selected for further development. System performance is numerically modelled and optimized and key performance aspects are empirically validated. The project deliverables are WEC technology specifications of high techno-economic performance technologies of TPL 7 or higher at TRL 3 with some key technology challenges investigated at higher TRL. These wave energy converter technology specifications will be made available to industry for further, full development and commercialisation (TRL 4 - TRL 9).

  11. Uncertainty characteristics of EPA's ground-water transport model for low-level waste performance assessment

    International Nuclear Information System (INIS)

    Yim, Man-Sung

    1995-01-01

    Performance assessment is an essential step either in design or in licensing processes to ensure the safety of any proposed radioactive waste disposal facilities. Since performance assessment requires the use of computer codes, understanding the characteristics of computer models used and the uncertainties of the estimated results is important. The PRESTO-EPA code, which was the basis of the Environmental Protection Agency's analysis for low-level-waste rulemaking, is widely used for various performance assessment activities in the country with no adequate information available for the uncertainty characteristics of the results. In this study, the groundwater transport model PRESTO-EPA was examined based on the analysis of 14 C transport along with the investigation of uncertainty characteristics

  12. Anthropometric, physiological and performance characteristics of elite team-handball players.

    Science.gov (United States)

    Chaouachi, Anis; Brughelli, Matt; Levin, Gregory; Boudhina, Nahla Ben Brahim; Cronin, John; Chamari, Karim

    2009-01-15

    The objective of this study was to provide anthropometric, physiological, and performance characteristics of an elite international handball team. Twenty-one elite handball players were tested and categorized according to their playing positions (goalkeepers, backs, pivots, and wings). Testing consisted of anthropometric and physiological measures of height, body mass, percentage body fat and endurance (VO(2max)), performance measures of speed (5, 10, and 30 m), strength (bench press and squat), unilateral and bilateral horizontal jumping ability, and a 5-jump horizontal test. Significant differences were found between player positions for some anthropometric characteristics (height and percentage body fat) but not for the physiological or performance characteristics. Strong correlations were noted between single leg horizontal jumping distances with 5-, 10-, and 30-m sprint times (r = 0.51-0.80; P team-handball players appear to be very similar. Single leg horizontal jumping distance could be a specific standardized test for predicting sprinting ability in elite handball players.

  13. Optimization of Performance and Emission Characteristics of Diesel Engine with Biodiesel Using Grey-Taguchi Method

    Directory of Open Access Journals (Sweden)

    Goutam Pohit

    2013-01-01

    Full Text Available Engine performances and emission characteristics of Karanja oil methyl ester blended with diesel were carried out on a variable compression diesel engine. In order to search for the optimal process response through a limited number of experiment runs, application of Taguchi method in combination with grey relational analysis had been applied for solving a multiple response optimization problem. Using grey relational grade and signal-to-noise ratio as a performance index, a particular combination of input parameters was predicted so as to achieve optimum response characteristics. It was observed that a blend of fifty percent was most suitable for use in a diesel engine without significantly affecting the engine performance and emissions characteristics.

  14. Governance and performance: the performance of Dutch hospitals explained by governance characteristics.

    Science.gov (United States)

    Blank, Jos L T; van Hulst, Bart Laurents

    2011-10-01

    This paper describes the efficiency of Dutch hospitals using the Data Envelopment Analysis (DEA) method with bootstrapping. In particular, the analysis focuses on accounting for cost inefficiency measures on the part of hospital corporate governance. We use bootstrap techniques, as introduced by Simar and Wilson (J. Econom. 136(1):31-64, 2007), in order to obtain more efficient estimates of the effects of governance on the efficiency. The results show that part of the cost efficiency can be explained with governance. In particular we find that a higher remuneration of the board as well as a higher remuneration of the supervisory board does not implicate better performance.

  15. Advanced Communications Technology Satellite (ACTS): Four-Year System Performance

    Science.gov (United States)

    Acosta, Roberto J.; Bauer, Robert; Krawczyk, Richard J.; Reinhart, Richard C.; Zernic, Michael J.; Gargione, Frank

    1999-01-01

    The Advanced Communications Technology Satellite (ACTS) was conceived at the National Aeronautics and Space Administration (NASA) in the late 1970's as a follow-on program to ATS and CTS to continue NASA's long history of satellite communications projects. The ACTS project set the stage for the C-band satellites that started the industry, and later the ACTS project established the use of Ku-band for video distribution and direct-to-home broadcasting. ACTS, launched in September 1993 from the space shuttle, created a revolution in satellite system architecture by using digital communications techniques employing key technologies such as a fast hopping multibeam antenna, an on-board baseband processor, a wide-band microwave switch matrix, adaptive rain fade compensation, and the use of 900 MHz transponders operating at Ka-band frequencies. This paper describes the lessons learned in each of the key ACTS technology areas, as well as in the propagation investigations.

  16. The Performativity of Risk Management Frameworks and Technologies

    DEFF Research Database (Denmark)

    Neerup Themsen, Tim; Skærbæk, Peter

    2018-01-01

    This article examines the long-term dynamics among a best-practice risk management framework, risk management technologies and the translation of uncertainties into risks by using a longitudinal case study of a large mega-project. We show that the framework and technologies through the visual power...... of impure risks challenges the predictions of the framework causing a false sense of security for the project objectives, and that the continuous readjustment of technologies, in particular, is necessary to ensure the long-term realisation of these predictions. Finally, this article contributes...... of inscriptions and the purifying work of risk consultants as experts establish the boundaries of the forms of uncertainties that are accepted and included as risks. We term the accepted and included risks ‘pure risks’ and the risks excluded after disagreement ‘impure risks’. We also show that the construction...

  17. Impacts of FDI Renewable Energy Technology Spillover on China’s Energy Industry Performance

    Directory of Open Access Journals (Sweden)

    Weiwei Liu

    2016-08-01

    Full Text Available Environmental friendly renewable energy plays an indispensable role in energy industry development. Foreign direct investment (FDI in advanced renewable energy technology spillover is promising to improve technological capability and promote China’s energy industry performance growth. In this paper, the impacts of FDI renewable energy technology spillover on China’s energy industry performance are analyzed based on theoretical and empirical studies. Firstly, three hypotheses are proposed to illustrate the relationships between FDI renewable energy technology spillover and three energy industry performances including economic, environmental, and innovative performances. To verify the hypotheses, techniques including factor analysis and data envelopment analysis (DEA are employed to quantify the FDI renewable energy technology spillover and the energy industry performance of China, respectively. Furthermore, a panel data regression model is proposed to measure the impacts of FDI renewable energy technology spillover on China’s energy industry performance. Finally, energy industries of 30 different provinces in China based on the yearbook data from 2005 to 2011 are comparatively analyzed for evaluating the impacts through the empirical research. The results demonstrate that FDI renewable energy technology spillover has positive impacts on China’s energy industry performance. It can also be found that the technology spillover effects are more obvious in economic and technological developed regions. Finally, four suggestions are provided to enhance energy industry performance and promote renewable energy technology spillover in China.

  18. Preventive Care Quality of Medicare Accountable Care Organizations: Associations of Organizational Characteristics With Performance.

    Science.gov (United States)

    Albright, Benjamin B; Lewis, Valerie A; Ross, Joseph S; Colla, Carrie H

    2016-03-01

    Accountable Care Organizations (ACOs) are a delivery and payment model aiming to coordinate care, control costs, and improve quality. Medicare ACOs are responsible for 8 measures of preventive care quality. To create composite measures of preventive care quality and examine associations of ACO characteristics with performance. This is a cross-sectional study of Medicare Shared Savings Program and Pioneer participants. We linked quality performance to descriptive data from the National Survey of ACOs. We created composite measures using exploratory factor analysis, and used regression to assess associations with organizational characteristics. Of 252 eligible ACOs, 246 reported on preventive care quality, 177 of which completed the survey (response rate=72%). In their first year, ACOs lagged behind PPO performance on the majority of comparable measures. We identified 2 underlying factors among 8 measures and created composites for each: disease prevention, driven by vaccines and cancer screenings, and wellness screening, driven by annual health screenings. Participation in the Advanced Payment Model, having fewer specialists, and having more Medicare ACO beneficiaries per primary care provider were associated with significantly better performance on both composites. Better performance on disease prevention was also associated with inclusion of a hospital, greater electronic health record capabilities, a larger primary care workforce, and fewer minority beneficiaries. ACO preventive care quality performance is related to provider composition and benefitted by upfront investment. Vaccine and cancer screening quality performance is more dependent on organizational structure and characteristics than performance on annual wellness screenings, likely due to greater complexity in eligibility determination and service administration.

  19. Aircrew Performance Cutting-Edge Technology: Emerging Human Performance Enhancement Technology Vision in Support of Operational Military Aviation Strategy

    National Research Council Canada - National Science Library

    Belland, Kris M

    2003-01-01

    Using cutting-edge technology to create a human factors advantage in military operations will contribute to success on the battlefield of the future whether below the surface, on the surface, in the air, or in space...

  20. Enhancing the ecological and operational characteristics of water treatment units at TPPs based on baromembrane technologies

    Science.gov (United States)

    Chichirova, N. D.; Chichirov, A. A.; Filimonova, A. A.; Saitov, S. R.

    2017-12-01

    The innovative baromembrane technologies for water demineralization were introduced at Russian TPPs more than 25 years ago. While being used in the power engineering industry of Russia, these technologies demonstrated certain advantages over the traditional ion-exchange and thermal technologies of makeup water treatment for steam boilers. Water treatment units based on the baromembrane technology are compact, easy to operate, and highly automated. The experience gained from the use of these units shows that their reliability depends directly on preliminary water treatment. The popular water pretreatment technology with coagulation by aluminum oxychloride proved to be inefficient during the seasonal changes of source water quality that occurs at some stations. The use of aluminum coagulant at pH 8 and higher does not ensure the stable and qualitative pretreatment regime: soluble aluminum forms slip on membranes of the ultrafiltration unit, thereby causing pollution and intoxication as well as leading to structural damages or worsening of mechanical properties of the membranes. The problem of increased pH and seasonal changes of the source water quality can be solved by substitution of the traditional coagulant into a new one. To find the most successful coagulant for water pretreatment, experiments have been performed on both qualitative and quantitative analysis of the content of natural organic matters in the Volga water and their structure. We have developed a software program and measured the concentrations of soluble aluminum and iron salts at different pH values of the source water. The analysis of the obtained results has indicated that iron sulfate at pH 6.0-10.2, in contrast to aluminum oxychloride, is not characterized by increased solubility. Thus, the basic process diagrams of water pretreatment based on baromembrane technologies with pretreatment through coagulation by iron salts and wastewater amount reducing from 60-40 to 5-2% have been introduced for

  1. Information Technology Adoption and Procedural Performance in Health Care

    Science.gov (United States)

    Shi, Yunfeng

    2010-01-01

    This dissertation studies two specific topics on information technologies in health care industry. (1) The status and change of integrated health care delivery system level IT spending and hospital level IT adoption between 1999 and 2006. (2) The potential link between hospital level IT adoptions and quality as quantified by procedural performance…

  2. Technological Advances, Human Performance, and the Operation of Nuclear Facilities

    Science.gov (United States)

    Corrado, Jonathan K.

    Many unfortunate and unintended adverse industrial incidents occur across the United States each year, and the nuclear industry is no exception. Depending on their severity, these incidents can be problematic for people, the facilities, and surrounding environments. Human error is a contributing factor in many such incidents. This dissertation first explored the hypothesis that technological changes that affect how operators interact within the systems of the nuclear facilities exacerbate the cost of incidents caused by human error. I conducted a review of nuclear incidents in the United States from 1955 through 2010 that reached Level 3 (serious incident) or higher on the International Nuclear Events Scale (INES). The cost of each incident at facilities that had recently undergone technological changes affecting plant operators' jobs was compared to the cost of events at facilities that had not undergone changes. A t-test determined a statistically significant difference between the two groups, confirming the hypothesis. Next, I conducted a follow-on study to determine the impact of the incorporation of new technologies into nuclear facilities. The data indicated that spending more money on upgrades increased the facility's capacity as well as the number of incidents reported, but the incident severity was minor. Finally, I discuss the impact of human error on plant operations and the impact of evolving technology on the 21st-century operator, proposing a methodology to overcome these challenges by applying the systems engineering process.

  3. Application of Advanced Technology to Improve Plant Performance. Safety and Performance in Current NPPs

    International Nuclear Information System (INIS)

    Hashemian, H.M.

    2011-01-01

    Advances in computer technologies, signal processing, analytical modeling, and the advent of wireless sensors have provided the nuclear industry with ample means to automate and optimize maintenance activities and improve safety, efficiency, and availability, while reducing costs and radiation exposure to maintenance personnel. This paper provides a review of these developments and presents examples of their use in the nuclear power industry and the financial and safety benefits that they have produced. As the current generation of nuclear power plants have passed their mid-life, increased monitoring of their health is critical to their safe operation. This is especially true now that license renewal of nuclear power plants has accelerated, allowing some plants to operate up to 60 years or more. Furthermore, many utilities are maximizing their power output through uprating projects and retrofits. This puts additional demand and more stress on the plant equipment such as the instrumentation and control (I and C) systems and the reactor internal components making them more vulnerable to the effects of aging, degradation, and failure. In the meantime, the nuclear power industry is working to reduce generation costs by adopting condition-based maintenance strategies and automation of testing activities. These developments have stimulated great interest in on-line monitoring (OLM) technologies and new diagnostic and prognostic methods to anticipate, identify, and resolve equipment and process problems and ensure plant safety, efficiency, and immunity to accidents. The foundation for much of the required technologies has already been established through 40 years of research and development (R and D) efforts performed by numerous organizations, scientists, and engineers around the world including the author. This paper provides examples of these technologies and demonstrates how the gap between some of the more important R and D efforts and end users have been filled

  4. Cogeneration Technology Alternatives Study (CTAS). Volume 3: Energy conversion system characteristics

    Science.gov (United States)

    1980-01-01

    Six current and thirty-six advanced energy conversion systems were defined and combined with appropriate balance of plant equipment. Twenty-six industrial processes were selected from among the high energy consuming industries to serve as a frame work for the study. Each conversion system was analyzed as a cogenerator with each industrial plant. Fuel consumption, costs, and environmental intrusion were evaluated and compared to corresponding traditional values. The advanced energy conversion technologies indicated reduced fuel consumption, costs, and emissions. Fuel energy savings of 10 to 25 percent were predicted compared to traditional on site furnaces and utility electricity. With the variety of industrial requirements, each advanced technology had attractive applications. Fuel cells indicated the greatest fuel energy savings and emission reductions. Gas turbines and combined cycles indicated high overall annual savings. Steam turbines and gas turbines produced high estimated returns. In some applications, diesels were most efficient. The advanced technologies used coal derived fuels, or coal with advanced fluid bed combustion or on site gasifications. Data and information for both current and advanced energy conversion technology are presented. Schematic and physical descriptions, performance data, equipment cost estimates, and predicted emissions are included. Technical developments which are needed to achieve commercialization in the 1985-2000 period are identified.

  5. How do task characteristics affect learning and performance? The roles of variably mapped and dynamic tasks.

    Science.gov (United States)

    Macnamara, Brooke N; Frank, David J

    2018-05-01

    For well over a century, scientists have investigated individual differences in performance. The majority of studies have focused on either differences in practice, or differences in cognitive resources. However, the predictive ability of either practice or cognitive resources varies considerably across tasks. We are the first to examine task characteristics' impact on learning and performance in a complex task while controlling for other task characteristics. In 2 experiments we test key theoretical task characteristic thought to moderate the relationship between practice, cognitive resources, and performance. We devised a task where each of several key task characteristics can be manipulated independently. Participants played 5 rounds of a game similar to the popular tower defense videogame Plants vs. Zombies where both cognitive load and game characteristics were manipulated. In Experiment 1, participants either played a consistently mapped version-the stimuli and the associated meaning of their properties were constant across the 5 rounds-or played a variably mapped version-the stimuli and the associated meaning of their properties changed every few minutes. In Experiment 2, participants either played a static version-that is, turn taking with no time pressure-or played a dynamic version-that is, the stimuli moved regardless of participants' response rates. In Experiment 1, participants' accuracy and efficiency were substantially hindered in the variably mapped conditions. In Experiment 2, learning and performance accuracy were hindered in the dynamic conditions, especially when under cognitive load. Our results suggest that task characteristics impact the relative importance of cognitive resources and practice on predicting learning and performance. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  6. Managerial Characteristics and its Impact on Organizational Performance: Evidence from Syria

    Directory of Open Access Journals (Sweden)

    Elias Milana

    2015-06-01

    Full Text Available This study aims to explore impact of managerial human capital in performance of a Syrian public organization, Directorate of Finance of province of Damascus, through use some of managerial characteristics are age, level of education, tenure and functional track. This study applied on a sample of 12 managers and 138 employees. The study reveals that there are no significant effect of age, level of education and functional track in performance of Directorate of Finance of province of Damascus, while there is a positive, strong and significant effect of tenure manager in organizational performance, which indicates that managerial characteristics almost irrelevant with performance of Directorate of Finance of the province of Damascus, and the public sector in general. Such results appear a need for efforts are invested in the formulation and implementation of human resource procedures and policies which can bring about effective change in behaviours and roles of the public managers and employees.

  7. Performance Characteristic of Cold Recycled Mixture with Asphalt Emulsion and Chemical Additives

    Directory of Open Access Journals (Sweden)

    Shaowen Du

    2015-01-01

    Full Text Available Three types of chemical additives were used to modify asphalt emulsion recycled mixture. These chemical additives include composite Portland cement (CPC, hydrated lime (HL, and a combination of hydrated lime and ground-granulated blast-furnace slag (GGBF. The influence of different additives on the recycled mixture performance was investigated by volumetric and strength tests, moisture susceptibility test, rutting resistance test, and low temperature bending test. To better understand its performance characteristic, the microstructure images of the recycled mixture were observed by environmental scanning electron microscope (ESEM. Test results demonstrate that the performance improvement of the emulsion recycled mixture depends on the types and content of chemical additives. Several recommendations are presented for the selection of chemical materials. Based on ESEM image analysis, the interface bonding mechanism is proposed to explain the performance characteristic of the recycled mixture with asphalt emulsion and cementitious materials.

  8. Development of Key Performance Indicators for the Engineering Technology Education Programs in Taiwan

    Science.gov (United States)

    Lee, Lung-Sheng; Lai, Chun-Chin

    2004-01-01

    In comparison with engineering, engineering technology is more practical and purposeful. The engineering technology education programs in Taiwan have been mainly offered in 56 universities/colleges of technology (UTs/CTs) and are anticipated to continuously improve their performance to prepare quality engineering technologists. However, it is…

  9. PERFORMANCE OF LEAKAGE POWER MINIMIZATION TECHNIQUE FOR CMOS VLSI TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    T. Tharaneeswaran

    2012-06-01

    Full Text Available Leakage power of CMOS VLSI Technology is a great concern. To reduce leakage power in CMOS circuits, a Leakage Power Minimiza-tion Technique (LPMT is implemented in this paper. Leakage cur-rents are monitored and compared. The Comparator kicks the charge pump to give body voltage (Vbody. Simulations of these circuits are done using TSMC 0.35µm technology with various operating temper-atures. Current steering Digital-to-Analog Converter (CSDAC is used as test core to validate the idea. The Test core (eg.8-bit CSDAC had power consumption of 347.63 mW. LPMT circuit alone consumes power of 6.3405 mW. This technique results in reduction of leakage power of 8-bit CSDAC by 5.51mW and increases the reliability of test core. Mentor Graphics ELDO and EZ-wave are used for simulations.

  10. Impact of Information and Communication Technologies in International Negotiation Performance

    OpenAIRE

    Cano, Jose Alejandro; Baena, Jose Jaime

    2015-01-01

    Objective – This article establishes relations between the level of importance of Information and Communication Technologies (ICT), the frequency of use of these tools, and the efficiency and efficacy achieved in the international negotiation processes.Design/methodology/approach – A research study is carried out in 180 import and / or export firms in Medellin city, and the proposed relations are explained through a theoretical model. With the information obtained, correlation and comparative...

  11. Performance Measurement of Information Technology Governance: a Case Study

    OpenAIRE

    Andry, Johanes Fernandes

    2016-01-01

    Established in 2001, XYZ Cargo is a Freight Forwarder Service Company specialized in the logistic transportation located in Jakarta. XYZ Cargo has broad experiences in both ocean freight and air freight service and has more than sixty agents of partnership around the world. XYZ Cargo has implemented Information Technology (IT) that covers all key aspects of business processes of the enterprise. It has an impact on the strategic and competitive advantages of its success. Many organizations hav...

  12. Power system restructuring and deregulation: trading, performance and information technology

    International Nuclear Information System (INIS)

    Loi Lei Lai

    2001-09-01

    Representatives from several countries have contributed to a book addressing the deregulation and restructuring of the electric power industry. Articles covered include guidance on asset management, transmission balancing and meter management systems, tools for studying competitive power markets, environmental impacts, costs and benefits, and the new strategies and technology available for power generation, transmission and distribution. The book should be of interest to power systems engineers, system operators, managers, planners and policy makers in the electric power business

  13. Virtual and augmented reality technologies in Human Performance: a review

    Directory of Open Access Journals (Sweden)

    Tânia Brusque Crocetta

    Full Text Available Abstract Introduction : Today's society is influenced by Information and Communication Technologies. Toys that were once built by hand have been reinterpreted and have become highly commercialized products. In this context, games using Augmented Reality (AR and Virtual Reality (VR technologies are present in the everyday lives of children, youth and adults. Objective : To investigate how Physical Education professionals in Brazil have been making use of AR and VR games to benefit their work. Materials and methods : We only included studies that addressed exercise or physical activity using AR or VR games. We searched the databases of Virtual Health Library (VHL and Scientific Electronic Library Online (SciELO, using the words augmented reality, virtual reality, exergames, Wii and serious games. Results : Nineteen articles were included in the systematic review. The most frequently used device was the Nintendo(r Wii, with over 25 different kinds of games. With regard to the subjects of the studies, four studies were conducted with healthy individuals (mean = 65.7, three with patients with Parkinson's disease (mean = 18.0, three with elderly women (mean = 7.7 and two with patients with stroke injury (mean = 6.0. Conclusion : Many physical therapists and occupational therapists use serious games with AR or VR technologies as another work tool, especially for rehabilitation practices. The fact that these technologies are also used in Physical Education classes in Brazil indicates that electronic games are available and can be a tool that can contribute to the widespread adoption of exercise as an enjoyable form of recreation.

  14. Holography: A Transformative Technology for Learning and Human Performance Improvement

    Science.gov (United States)

    Frazer, Gary W.; Stevens, George H.

    2015-01-01

    Most past and current learning technologies have been one- or two-dimensional in presentation. This may be fine if one is looking at a map or even a fine painting. However, to fully appreciate the detail of a statue or a machine part, it is better to be able to look at it from all sides. Use of holographic images allows an item to be shared with a…

  15. Characteristics of shift work and their impact on employee performance and wellbeing: a literature review

    OpenAIRE

    Dall'ora, Chiara; Griffiths, P.; Ball, J.; Recio Saucedo, A.

    2016-01-01

    BACKGROUND: Shift work is recognised as a component of work organisation that may affect the balance between employee’s efficiency, effectiveness and wellbeing. Shift work is frequent in healthcare and for nurses in particular, as they typically comprise a large proportion of the workforce in healthcare AIM: To identify the characteristics of shift work that have an effect on employee’s performance (including job performance, productivity, safety, quality of care delivered, errors, adverse ev...

  16. Performance characteristics of broilers fed graded levels of Moringa oleifera leaf meal

    OpenAIRE

    Ayo-Ajasa, O.Y.; Abiona, J.A.; Fafiolu, A.O.; Egbeyale, L.T.; Njoku1, C.P.; Omotayo1, I.G.; Odeyemi1, A.Y.; Abel, F.A.S.

    2016-01-01

    Cost of conventional protein sources is on the increase recently; hence, there is the need for cheaper alternative sources that will not compromise the performance characteristics of broiler birds taking into consideration the cost of production. Moringa leaf meal has been reported to increase the performance of broiler birds due to its rich protein content. Two hundred day-old broiler chicks were used to assess the effects of partial replacement of soya bean meal with Moringa (Moringa oleife...

  17. Contributions of welding technology to power plant performance

    International Nuclear Information System (INIS)

    Childs, W.J.

    1995-01-01

    Welding repairs can be a very major factor in the time and cost of maintenance outages of a power plant. The use of advanced equipment and procedures for welding can contribute significantly to reducing maintenance costs and increasing reliability. Plant failures have too often been caused by problems associated with welding, some due to improper choice of base materials, others due to welding defects. For example, stress corrosion cracking in weldments in BWR austenitic stainless steel piping was a major source of loss of availability in the 1980s. Examples of the use of improved welding equipment and procedures has been demonstrated to reduce outage time and improved weld integrity in several major areas. New welding techniques, such as laser welding, have the potential for addressing maintenance problems that can not be addressed at all with conventional welding technology and/or may provide a means of reducing greatly the time and cost of welding fabrications or repair. Methods of ensuring that the best available technology is applied in weld repair is a major problem today in the utility industry. Solutions need to be sought to remedy this situation. The key role of welding in minimizing plant outages is being recognized and steps taken to further the development and use of optimum technology

  18. Technological Factors, User Characteristics and Didactic Strategies in Educational Virtual Environments

    DEFF Research Database (Denmark)

    Natsis, Antonios; Vrellis, Ioannis; Papachristos, Nikiforos

    2012-01-01

    Technological factors, user characteristics and didactic strategies do not function consistently across Educational Virtual Environments. This study investigates the impact of viewing condition and didactic strategy on attention allocation, suspension of disbelief, spatial presence, and learning...... outcomes in an Educational Virtual Environment concerning ancient Greek pottery. Our results show that the viewing condition does not affect attention allocation, suspension of disbelief, and spatial presence. Learning outcomes are better in the monoscopic viewing condition. Didactic strategy has an impact...... on suspension of disbelief and learning outcomes. Domain specific interest associates with higher level of attention allocation and spatial presence, while spatial presence is not related to learning outcomes. More research is needed in order to identify the role of each one of the above factors in Educational...

  19. Performance of safety management systems in Spanish food service establishments in view of their context characteristics

    NARCIS (Netherlands)

    Luning, P.A.; Chinchilla, A.C.; Jacxsens, L.; Kirezieva, K.K.; Rovira, J.

    2013-01-01

    Food service establishments (FSE) operate under restricted technological and organisational circumstances, making them susceptible to food safety problems as reported frequently. Aim of this study was to get insight in Food Safety Management System (FSMS) performance in different types of FSE in

  20. Performance Characteristics of Long-Track Speed Skaters : A Literature Review

    NARCIS (Netherlands)

    Konings, Marco J.; Elferink-Gemser, Marije T.; Stoter, Inge K.; van der Meer, Dirk; Otten, Egbert; Hettinga, Florentina J.

    Speed skating is an intriguing sport to study from different perspectives due to the peculiar way of motion and the multiple determinants for performance. This review aimed to identify what is known on (long-track) speed skating, and which individual characteristics determine speed skating

  1. Effects of sweeteners on individual feed intake characteristics and performance in group-housed weanling pigs

    NARCIS (Netherlands)

    Sterk, A.R.; Schlegel, P.; Mul, A.J.; Ubbink-Blanksma, M.; Bruininx, E.M.A.M.

    2008-01-01

    To assess the effects of 2 high intensity sodium saccharine based sweeteners on individual feed intake characteristics and performance of group-housed weaned pigs, 198 26-d-old weanling pigs were given ad libitum access to 3 dietary treatments: containing no additional sweetener (Control), 150 mg

  2. Using Differential Item Functioning Procedures to Explore Sources of Item Difficulty and Group Performance Characteristics.

    Science.gov (United States)

    Scheuneman, Janice Dowd; Gerritz, Kalle

    1990-01-01

    Differential item functioning (DIF) methodology for revealing sources of item difficulty and performance characteristics of different groups was explored. A total of 150 Scholastic Aptitude Test items and 132 Graduate Record Examination general test items were analyzed. DIF was evaluated for males and females and Blacks and Whites. (SLD)

  3. Epilepsy in the School Aged Child: Cognitive-Behavioral Characteristics and Effects on Academic Performance.

    Science.gov (United States)

    Black, Kathryn C.; Hynd, George W.

    1995-01-01

    Children with epilepsy frequently display cognitive sequelae that are overlooked or misunderstood by educational personnel, yet may adversely impact academic performance. Reviews common cognitive-behavioral characteristics of children with epilepsy, typical effects of anticonvulsant medications, and various periictal phenomena and their relative…

  4. Performance characteristics of an excimer laser (XeCl) with single ...

    Indian Academy of Sciences (India)

    2017-01-10

    Jan 10, 2017 ... Performance characteristics of an excimer laser (XeCl) with single-stage magnetic ... the stress can increase the lifetime of the switches and ..... work. References. [1] Ying-Tung Chen, Kris Naessens, Roel Bates, Yunn-Shiuan.

  5. Vein visualization: patient characteristic factors and efficacy of a new infrared vein finder technology.

    Science.gov (United States)

    Chiao, F B; Resta-Flarer, F; Lesser, J; Ng, J; Ganz, A; Pino-Luey, D; Bennett, H; Perkins, C; Witek, B

    2013-06-01

    We investigated the patient characteristic factors that correlate with identification of i.v. cannulation sites with normal eyesight. We evaluated a new infrared vein finding (VF) technology device in identifying i.v. cannulation sites. Each subject underwent two observations: one using the conventional method (CM) of normal, unassisted eyesight and the other with the infrared VF device, VueTek's Veinsite™ (VF). A power analysis for moderate effect size (β=0.95) required 54 samples for within-subject differences. Patient characteristic profiles were obtained from 384 subjects (768 observations). Our sample population exhibited an overall average of 5.8 [95% confidence interval (CI) 5.4-6.2] veins using CM. As a whole, CM vein visualization were less effective among obese [4.5 (95% CI 3.8-5.3)], African-American [4.6 (95% CI 3.6-5.5 veins)], and Asian [5.1 (95% CI 4.1-6.0)] subjects. Next, the VF technology identified an average of 9.1 (95% CI 8.6-9.5) possible cannulation sites compared with CM [average of 5.8 (95% CI 5.4-6.2)]. Seventy-six obese subjects had an average of 4.5 (95% CI 3.8-5.3) and 8.2 (95% CI 7.4-9.1) veins viewable by CM and VF, respectively. In dark skin subjects, 9.1 (95% CI 8.3-9.9) veins were visible by VF compared with 5.4 (95% CI 4.8-6.0) with CM. African-American or Asian ethnicity, and obesity were associated with decreased vein visibility. The visibility of veins eligible for cannulation increased for all subgroups using a new infrared device.

  6. Human Performance Technology and Knowledge Management: A Case Study

    Science.gov (United States)

    Massey, Anne P.; Montoya-Weiss, Mitzi M.; O'Driscoll, Tony M.

    2005-01-01

    As organizations respond to competitive environments and strive to enhance performance, knowledge management (KM) has increasingly become a strategic activity. A KM strategy entails consciously helping people share and put knowledge into action. A key challenge is how to develop and implement KM solutions that provide performance support to…

  7. FY 1995 Blue Book: High Performance Computing and Communications: Technology for the National Information Infrastructure

    Data.gov (United States)

    Networking and Information Technology Research and Development, Executive Office of the President — The Federal High Performance Computing and Communications HPCC Program was created to accelerate the development of future generations of high performance computers...

  8. Causal Dynamic Relationships between Political–Economic Factors and Export Performance in the Renewable Energy Technologies Market

    Directory of Open Access Journals (Sweden)

    Bongsuk Sung

    2018-04-01

    Full Text Available This study explores how political–economic forces could affect export performance in the renewable energy technologies market. We conduct panel framework analyses to verify the characteristics of panel data for 19 countries before establishing the panel estimator meant to test the effects of political–economic forces on export specialization. We consider the results of the panel framework analyses and develop an empirical model to test casual dynamic relationships between political–economic forces and export performance. The results from the least squares dummy variable-corrected estimation indicate that the major factors promoting the export specialization of renewable energy technologies are, in order of decreasing importance, public pressure, market size, and government demand-pull policy. However, the traditional energy industry has no significant effect on export performance. Finally, this study finds that dynamic effects exist in all estimations.

  9. Physical, chemical, technological and sensory characteristics of Frankfurter type sausage containing okara flour

    Directory of Open Access Journals (Sweden)

    Regina Kitagawa Grizotto

    2012-09-01

    Full Text Available The addition of okara flour to an emulsified meat product (Frankfurter type sausage was evaluated based on the physical, chemical, technological, and sensory characteristics of the final product. Okara, residue from soymilk production, was provided by two soymilk producing companies whose production systems were based on the hot disintegration of the decorticated (company B or undecorticated (company A soybeans. The okara was dehydrated using a flash dryer and then ground into flour (>420 µm. However, The okara flours A and B showed approximately the same amount of protein (35 and 40 g.100 g-1 dwb. However, the okara flour A presented higher values (p < 0.05 for all technological functional properties studied (emulsification capacity, emulsion stability, protein solubility, and water hold capacity than those of okara flour B. The A and B okara flours were used in a frankfurter sausage formulation as substitution of 1.5% and 4% of meat. The results showed that the sausages containing okara flours A and B, as well as the control sausage, were accepted by the sensory panel. Moreover, there were no significant differences (p < 0.05 in the physical (color, objective texture, and emulsion stability and chemical (pH and proximate composition measurements of the sausages with and without the okara flour.

  10. Chemical composition and technological characteristics of wines from red grape varieties, selected in Bulgaria

    Directory of Open Access Journals (Sweden)

    V. Haygarov

    2017-03-01

    Full Text Available Abstract. Chemical analysis of grapes and technological characterization of wines from red varieties Storgoziya, Kaylashky rubin, Trapezitza, Rubin and Bouquet, created by the method of intraspecific and interspecific hybridization at the Institute of Viticulture and Enology – Pleven, Bulgaria were made. The technological maturity of the grapes as raw material for producing quality red wines was determined. Rubin variety was with the highest sugar content - 3 23.10±0.73 %, titratable acids - 6.18±0.34 g/dm and pH 3.40±0.71. The other varieties were with optimal condition for the production of red wines in terms of sugars and titratable acids. The chemical composition and organoleptic characteristics of the experimental wine samples were established. The ethyl alcohol content in the produced wines was in the range from 12.33±0.23 vol. % (Bouquet to 13.31±0.34 vol. % (Kaylashky rubin. The content of titratable acids was in 3 3 the range of 5.33±0.43 g/dm (Trapezitza up to 6.88±0.21 g/dm (Kaylashky rubin. There were no significant differences in the analyzed indicators and taste evaluation between experimental wines and wine of Vitis vinifera – Pinot noir grape variety used as control sample

  11. Technological Characteristics of the Longissimus Dorsi Muscle of Pig Depending on the Genetic Type

    Directory of Open Access Journals (Sweden)

    Consuela Roibu

    2012-05-01

    Full Text Available The processes of technological processing of meat carried out in optimal conditions, require a good knowledge of the water capacity of bearings by the raw material that makes the manufacturing processes of the various preparations. Technological characteristics of pigmeat analyzed in this paper are represented by water retention ability, capacity of hydration and the degree of perselation. The researches have been conducted on 40 samples, taken from the muscle of the longissimus dorsi from breeds Marele Alb, Landrace, Line S 345 Periş, Duroc, Hampshire and Perhib, F1 hybrids (Marele AlbxLandrace xPietrain and F1 (Marele AlbxLandrace xSeghers. Water retention capacity has been appreciated by many indicators obtained from the pressing of the sample, according to the method Grau-Hamm. The largest capacity aircraft meets the breed Duroc (47.631, followed by the great white (43.33, LSP 345 Periş (42.87 and the hybrid Perhib (42.731. Water retention capacity, expressed as wet surface, stated on the first Landrace breed (30.012, followed by the Hampshire breed and F1xSeghers (29.602 hybrid Perhib (28.6 breed of LSP 345 Periş (28.361, the lowest value is passed to the race Duroc (22.344.

  12. Research on PM2.5 time series characteristics based on data mining technology

    Science.gov (United States)

    Zhao, Lifang; Jia, Jin

    2018-02-01

    With the development of data mining technology and the establishment of environmental air quality database, it is necessary to discover the potential correlations and rules by digging the massive environmental air quality information and analyzing the air pollution process. In this paper, we have presented a sequential pattern mining method based on the air quality data and pattern association technology to analyze the PM2.5 time series characteristics. Utilizing the real-time monitoring data of urban air quality in China, the time series rule and variation properties of PM2.5 under different pollution levels are extracted and analyzed. The analysis results show that the time sequence features of the PM2.5 concentration is directly affected by the alteration of the pollution degree. The longest time that PM2.5 remained stable is about 24 hours. As the pollution degree gets severer, the instability time and step ascending time gradually changes from 12-24 hours to 3 hours. The presented method is helpful for the controlling and forecasting of the air quality while saving the measuring costs, which is of great significance for the government regulation and public prevention of the air pollution.

  13. Technological characteristics of yeast-containing cakes production using waxy wheat flour

    Directory of Open Access Journals (Sweden)

    K. Iorgachova

    2016-12-01

    Full Text Available This article shows the feasibility of using waxy wheat flour, the starch of which doesn`t contain amylose, in order to stabilize the quality of yeast-containing cakes. The influence of the waxy wheat flour mass fraction and the stage of its adding on the physical, chemical and organoleptic characteristics of the products are studied. According to the technological properties of a new type of wheat flour, two methods of its adding are proposed ‒ adding the maximum amount of waxy wheat flour at dough kneading stage or using the mixture of waxy and bakery wheat flours for kneading sourdough and dough. It is shown that the replacement of 60 % bakery wheat flour with waxy wheat flour in the recipe of yeast-containing cakes at the dough kneading stage contributes to the production of products with higher quality and organoleptic characteristics compared to both the control and cakes based on a mixture of different types of wheat flour. These samples are characterized by increased by 1.7 – 11.3 % specific volume, porosity – 2.6 – 5.5 % and the total deformation of the crumb – 6.5 – 41.4 %.

  14. Advanced Fuel UCO Preparation Technology for HTGR (Characteristics of Carbon Black)

    International Nuclear Information System (INIS)

    Jeong, Kyung Chai; Oh, S. C.; Kim, Y. K.; Cho, M. S.; Kim, W. K.; Kim, Y. M.; Lee, Y. W.; Cho, H. J.; Shin, E. J.

    2010-06-01

    NGNP program for high specification of HTGR nuclear fuel through the GEN IV study is be progressed. Furthermore, because the NGNP program have a highly focused goal like UCO kernel, kernel fabrication and coating types varied which made selection of a US reference fabrication process. In this study, it was evaluated from the reviews on the UO2 and UCO kernel fabrication technologies and its particle characteristics. For improving the UCO qualities, first it was improved the kernel fabrication processes and carbon dispersion method also. New method for carbon dispersion in broth solution was developed, and its characteristics was evaluated from the AGR irradiation tests used the UCO kernel. In fabrication process, also process parameter variation tests in both forming and sintering steps led to an increased understanding of the acceptable ranges for process parameters and additional reduction in required operating times. Another result of this test program was to double the kernel production rate. Following the development tests, approximately 40 kg of natural uranium UCO kernels have been produced for use in coater scale up tests, and approximately 10 kg of low enriched uranium UCO kernels for use in the AGR-2 experiment

  15. The effect of information technology investment on firm-level performance in the health care industry.

    Science.gov (United States)

    Thouin, Mark F; Hoffman, James J; Ford, Eric W

    2008-01-01

    The return on investment for information technology (IT) has been the subject of much debate throughout the history of management information systems research. Often referred to as the productivity paradox, increased IT investments have not been consistently associated with increased productivity. Understanding individual IT factors that directly contribute to business value should provide insight into the productivity paradox. The effects of 3 different firm-level IT characteristics on financial performance in the health care industry are studied. Specifically, the effects of IT budget, IT outsourcing, and the relative number of IT personnel on firm-level financial performance are analyzed. Regression analysis of archival survey data for 914 Integrated Healthcare Delivery Systems is performed. IT budgetary expenditures and the number of IT services outsourced are associated with increases in the profitability of Integrated Healthcare Delivery Systems, whereas increases in IT personnel are not significantly associated with increased profitability. Each one tenth of a percentage increase in IT expenditures is associated with approximately $100,000 in increased profit, and each additional IT service outsourced is associated with approximately $950,000 in increased profit for an average-sized Integrated Healthcare Delivery System. To increase profitability, IT administrators should increase IT budgetary expenditures along with IT outsourcing levels. IT administrators in the health care industry can use such findings during budgeting cycles to justify increased investments in IT personnel as being budget neutral while increasing organizational capacity.

  16. Framatome technologies successfully performs SG re-sleeving at Kewaunee

    International Nuclear Information System (INIS)

    Anon.

    1997-01-01

    Framatome Technologies teamed with ABB-CE (Connecticut) to remove previously installed sleeves from the Kewaunee nuclear power stations steam generator tubes and install new sleeves. Recent inspections indicated problems at the upper joint of many of the previous sleeves. The process involved removing most of the hydraulic expansion joint (HEJ) sleeve, expanding the sleeve remnant and the tube section at the upper joint, and installing a TIG-welded sleeve that bridges the problem portion of the tube that the HEJ sleeve covered

  17. 40 CFR 450.24 - New source performance standards reflecting the best available demonstrated control technology...

    Science.gov (United States)

    2010-07-01

    ... performance standards reflecting the best available demonstrated control technology (NSPS). Any new source... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards reflecting the best available demonstrated control technology (NSPS). 450.24 Section 450.24 Protection of...

  18. LMS Use and Instructor Performance: The Role of Task-Technology Fit

    Science.gov (United States)

    McGill, Tanya; Klobas, Jane; Renzi, Stefano

    2011-01-01

    The introduction of learning management systems (LMS) has changed the way in which instructors work. This paper uses Goodhue and Thompson's (1995) technology-to-performance chain (TPC) to explore the roles of task-technology fit (TTF) and level of LMS use in the performance impacts of LMS for instructors. A mixed method approach was used: an…

  19. Human Performance Technology (HPT): An Examination of Definitions through Dependent and Independent Variables.

    Science.gov (United States)

    Irlbeck, Sonja A.

    2002-01-01

    Provides a chronological perspective of human performance technology (HPT) definitions and an evaluation of them in terms of independent and dependent variables. Discusses human competence and performance technology and compares the definitions with the goals that have been articulated for HPT. (Author/LRW)

  20. MSFC Turbine Performance Optimization (TPO) Technology Verification Status

    Science.gov (United States)

    Griffin, Lisa W.; Dorney, Daniel J.; Snellgrove, Lauren M.; Zoladz, Thomas F.; Stroud, Richard T.; Turner, James E. (Technical Monitor)

    2002-01-01

    Capability to optimize for turbine performance and accurately predict unsteady loads will allow for increased reliability, Isp, and thrust-to-weight. The development of a fast, accurate, validated aerodynamic design, analysis, and optimization system is required.

  1. A study on the performance and emission characteristics of esterified pinnai oil tested in VCR engine.

    Science.gov (United States)

    Ashok Kumar, T; Chandramouli, R; Mohanraj, T

    2015-11-01

    Biodiesel is a clean renewable fuel derived from vegetable oils and animal fats. It is biodegradable, oxygenated, non toxic and free from sulfur and aromatics. The biodiesel prepared from pinnai oil undergoes acid esterification followed by alkaline transesterification process. The fatty acid methyl esters components were identified using gas chromatography and compared with the standard properties. The properties of biodiesel are comparable with diesel. The yield of the biodiesel production depends upon the process parameters such as reaction temperature, pH, time duration and amount of catalyst. The yield of biodiesel by transesterification process was 73% at 55°C. This fuel was tested in a variable compression ratio engine with blend ratios of B10 and B20. During the test runs the compression ratio of the engine was varied from 15:1 to 18:1 and the torque is adjusted from zero to maximum value of 22Nm. The performance characteristics such as the brake thermal efficiency, brake specific energy consumption and exhaust gas temperature of the engine are analyzed. The combustion characteristics of biodiesel like ignition delay, combustion duration and maximum gas temperature and the emission characteristics are also analyzed. The performance characteristics, combustion characteristics and engine emission are effective in the variable compression ratio engine with biodiesel and it is compared with diesel. Copyright © 2015 Elsevier Inc. All rights reserved.

  2. Effect of branding management on technology performance : a case study

    OpenAIRE

    2012-01-01

    M.Ing. This dissertation aims to identify the effects contributed by branding on organisational performance, as branding may contribute positively or negatively to the company sales performance. Many customers align quality products with certain brands only. Some organisations over price their products because they have guaranteed space in the market and had built solid relationships with their customers. Due to many different good products which do not do well in the market because of poo...

  3. Reader characteristics linked to detection of pulmonary nodules on radiographs: ROC vs. JAFROC analyses of performance

    Science.gov (United States)

    Kohli, Akshay; Robinson, John W.; Ryan, John; McEntee, Mark F.; Brennan, Patrick C.

    2011-03-01

    The purpose of this study is to explore whether reader characteristics are linked to heightened levels of diagnostic performance in chest radiology using receiver operating characteristic (ROC) and jackknife free response ROC (JAFROC) methodologies. A set of 40 postero-anterior chest radiographs was developed, of which 20 were abnormal containing one or more simulated nodules, of varying subtlety. Images were independently reviewed by 12 boardcertified radiologists including six chest specialists. The observer performance was measured in terms of ROC and JAFROC scores. For the ROC analysis, readers were asked to rate their degree of suspicion for the presence of nodules by using a confidence rating scale (1-6). JAFROC analysis required the readers to locate and rate as many suspicious areas as they wished using the same scale and resultant data were used to generate Az and FOM scores for ROC and JAFROC analyses respectively. Using Pearson methods, scores of performance were correlated with 7 reader characteristics recorded using a questionnaire. JAFROC analysis showed that improved reader performance was significantly (pchest specialty (pchest radiographs (pchest readings per year (pchest radiographs (pchest specialty, hours reading per week and number of radiographs read per year. Also, JAFROC is a more powerful predictor of performance as compared to ROC.

  4. Attentional models of multitask pilot performance using advanced display technology.

    Science.gov (United States)

    Wickens, Christopher D; Goh, Juliana; Helleberg, John; Horrey, William J; Talleur, Donald A

    2003-01-01

    In the first part of the reported research, 12 instrument-rated pilots flew a high-fidelity simulation, in which air traffic control presentation of auditory (voice) information regarding traffic and flight parameters was compared with advanced display technology presentation of equivalent information regarding traffic (cockpit display of traffic information) and flight parameters (data link display). Redundant combinations were also examined while pilots flew the aircraft simulation, monitored for outside traffic, and read back communications messages. The data suggested a modest cost for visual presentation over auditory presentation, a cost mediated by head-down visual scanning, and no benefit for redundant presentation. The effects in Part 1 were modeled by multiple-resource and preemption models of divided attention. In the second part of the research, visual scanning in all conditions was fit by an expected value model of selective attention derived from a previous experiment. This model accounted for 94% of the variance in the scanning data and 90% of the variance in a second validation experiment. Actual or potential applications of this research include guidance on choosing the appropriate modality for presenting in-cockpit information and understanding task strategies induced by introducing new aviation technology.

  5. Technological Innovation Management and its Role in Performance of Organizations

    Directory of Open Access Journals (Sweden)

    Laura-Diana Radu

    2012-10-01

    Full Text Available This paper aims to identify the main benefits of technological innovation in organizations and how it should be managed to ensure economic efficiency. The current level of social and economic evolution was possible only through active involvement of individuals and organizations in the innovative process. Adoption of appropriate policies and strategies at institutional, national and international level has significant impact on both the innovation process and innovation results. At company level, involvement in an innovative process depends on the financial and human resources and on the availability and interest of management and employees. The main motivating factor in adoption of technological innovation is, most often, obtaining financial benefits. This reflects itself either as a direct increase in profits, or by obtaining competitive advantage which leads, in the long run, to profits increase and achieving a favorable position on the market. Should not be neglected other motivating factors of innovation, such as compliance with environmental standards, ensuring a secure position on the market with opportunities for further expansion, reducing the cost of raw materials and / or production process, improving company image, attitude and achievements of partners in the field (competitors, suppliers, customers etc. Managers need to carefully analyze these factors and decide the manner and degree of involvement in an innovative process.

  6. Performance characteristics of a Vertical Axis Wind Turbine (VAWT) under transient conditions

    OpenAIRE

    Colley, Gareth; Mishra, Rakesh

    2011-01-01

    The present work investigates the performance characteristics of a novel Vertical Axis Wind Turbine (VAWT) for use in the urban environment. Here the performance of the wind turbine has been analyzed experimentally using a full scale prototype measuring 2.0m diameter and 1.0m in height. The turbine was located at the exit of a 0.6m x 0.6m wind tunnel section and was subjected to a jet flow. The performance output from the turbine has been obtained using a torque transducer unit which provides...

  7. Performance characteristics of digital vs film screen mammography in community practice.

    Science.gov (United States)

    Dabbous, Firas; Dolecek, Therese A; Friedewald, Sarah M; Tossas-Milligan, Katherine Y; Macarol, Tere; Summerfelt, Wm Thomas; Rauscher, Garth H

    2018-05-01

    We compared the performance characteristics of 297 629 full field digital (FFDM) and 416 791 screen film mammograms (SFM). Sensitivity increased with age, decreased with breast density, and was lower for more aggressive and lobular tumors. While sensitivity did not differ significantly by modality, specificity was generally 1%-2% points higher for FFDM than for SFM across age and breast density categories. The lower recall rate for FFDM vs SFM in our study may partially explain performance differences by modality. In this large health care organization, modest gains in performance were achieved with the introduction of FFDM as a replacement for SFM. © 2017 Wiley Periodicals, Inc.

  8. Performance and combustion characteristics of direct-injection stratified-charge rotary engines

    Science.gov (United States)

    Nguyen, Hung Lee

    1987-01-01

    Computer simulations of the direct-injection stratified-charge (DISC) Wankel engine have been used to calculate heat release rates and performance and efficiency characteristics of the 1007R engine. Engine pressure data have been used in a heat release analysis to study the effects of heat transfer, leakage, and crevice flows. Predicted engine performance data are compared with experimental test data over a range of engine speeds and loads. An examination of methods to improve the performance of the Wankel engine with faster combustion, reduced leakage, higher compression ratio, and turbocharging is presented.

  9. Microcystin Detection Characteristics of Fluorescence Immunochromatography and High Performance Liquid Chromatography

    International Nuclear Information System (INIS)

    Pyo, Dong Jin; Park, Geun Young; Choi, Jong Chon; Oh, Chang Suk

    2005-01-01

    Different detection characteristics of fluorescence immunochromatography method and high performance liquid chromatography (HPLC) method for the analysis of cyanobacterial toxins were studied. In particular, low and high limits of detection, detection time and reproducibility and detectable microcystin species were compared when fluorescence immunochromatography method and high performance liquid chromatography method were applied for the detection of microcystin (MC), a cyclic peptide toxin of the freshwater cyanobacterium Microcystis aeruginosa. A Fluorescence immunochromatography assay system has the unique advantages of short detection time and low detection limit, and high performance liquid chromatography detection method has the strong advantage of individual quantifications of several species of microcystins

  10. Performance characteristics of long-track speed skaters: a literature review.

    Science.gov (United States)

    Konings, Marco J; Elferink-Gemser, Marije T; Stoter, Inge K; van der Meer, Dirk; Otten, Egbert; Hettinga, Florentina J

    2015-04-01

    Speed skating is an intriguing sport to study from different perspectives due to the peculiar way of motion and the multiple determinants for performance. This review aimed to identify what is known on (long-track) speed skating, and which individual characteristics determine speed skating performance. A total of 49 studies were included. Based on a multidimensional performance model, person-related performance characteristics were categorized in anthropometrical, technical, physiological, tactical, and psychological characteristics. Literature was found on anthropometry, technique, physiology, and tactics. However, psychological studies were clearly under-represented. In particular, the role of self-regulation might deserve more attention to further understand mechanisms relevant for optimal performance and for instance pacing. Another remarkable finding was that the technically/biomechanically favourable crouched skating technique (i.e. small knee and trunk angle) leads to a physiological disadvantage: a smaller knee angle may increase the deoxygenation of the working muscles. This is an important underlying aspect for the pacing tactics in speed skating. Elite speed skaters need to find the optimal balance between obtaining a fast start and preventing negative technical adaptations later on in the race by distributing their available energy over the race in an optimal way. More research is required to gain more insight into how this impacts on the processes of fatigue and coordination during speed skating races. This can lead to a better understanding on how elite speed skaters can maintain the optimal technical characteristics throughout the entire race, and how they can adapt their pacing to optimize all identified aspects that determine performance.

  11. Performance characteristics of plane-wall venturi-like reverse flow diverters

    International Nuclear Information System (INIS)

    Smith, G.V.; Counce, R.M.

    1982-01-01

    The results of an analytical and experimental study of plane-wall venturi-like reverse flow diverters (RFD) are presented. In general, the flow characteristics of the RFD are reasonably well predicted by the mathematical model of the RFD, although a divergence between theory and data is observed for the output characteristics in the reverse flow mode as the output impedance is reduced. Overall, the performance of these devices indicates their usefulness in fluid control and fluid power systems, such as displacement pumping systems

  12. The effect of management team characteristics on performance and style extremity of mutual fund portfolios

    Directory of Open Access Journals (Sweden)

    Liu Qiong

    2014-01-01

    Full Text Available Purpose: Along with mutual funds’ scale and quantity expanding for our country, it is common for fund management companies hiring new managers or the original fund managers mobilizing from one to another. The high liquidity of fund managers makes different managers regroup to manage the funds that belong to the same fund management company in each fund year. The characteristics of these different management team will influence the fund performance, and also affect the earnings of the fund management company and portfolio investors. The purpose of this paper is as follows. First, evaluating the effect of management team characteristics on portfolio characteristics: risk, performance, and extremity. Second, testing the hypothesis that the ranking of mid-year performance have effect on investment style extremity and research what relationship exists between this phenomenon and management team characteristics in depth.Design/methodology/approach: On the analysis of the relationships between the management team characteristics and portfolio characteristics, a series of OLS regressions is run where the time series regression model (the factor model and cross-sectional regression are included based on using the STATA, EVIEWS and MATLAB. The validity and practicability of the model will be verified in the paper. All of the above are aimed at achieving portfolio optimization and realizing the maximization of the interests of fund management companies and investors.Findings: The main findings are as follows. Teams with more doctors or MBA (CPA and CFA hold more risky portfolios, while teams with long team tenure hold less. More members and large gender diversity have negative effect on performance, and the opposite is age diversity. Teams with more members and long tenure tend to hold less extreme style decisions, but age diversity is related to more. Besides, tournament hypothesis does exist in China investment funds industry especially when the

  13. Preparation and Characteristics of Porous Ceramics by a foaming Technology at Low Temperature

    Science.gov (United States)

    Zhang, H. Q.; Wang, S. P.; Wen, J.; Wu, N.; Xu, S. H.

    2017-12-01

    Recycling and converting coal gangue and red mud into porous ceramics with good performance is a feasible disposal route. In this present work, porous foam ceramics was prepared using coal gangue and red mud as main raw materials at low sintering temperature, The amount of coal gangue and red mud were up to 70 wt%. To regulate the forming and sintering performance of the product, quartz sands and clay material were added to the formula. The green body was formed by a foaming technology using aluminum powders as foaming agents at room temperature. After foamed, the specimens were dried at 60-80 °C, and then calcined at 1060°C. Effects of concentration of NaOH and amount of aluminum powders on the phase, mechanical properties and microstructure were investigated here. Such study is expected to provide a new utilization route of the coal gangue and red mud, and brings both intensive environmental and economic benefits.

  14. Motivation, Compensation, and Performance for Science and Technological Teachers

    Science.gov (United States)

    Abast, R. M.; Sangi, N. M.; Tumanduk, M. S. S. S.; Roring, R.

    2018-02-01

    This research is operationally aimed to obtain the result of analysis and interpretation about: relationship of achievement motive, compensation with performance at a junior high school in Manado, Indonesia. This research applies a quantitative approach with correlation analysis method. The research was conducted at one junior high school in Manado, Indonesia. The results showed achievement motive at the school teachers is quite high. This result means that, generally, the teachers of the school have a desire to improve achievement; the performance at the school is good enough. This result means that in general, the performance of teachers at the school is increasing, there is a linkage degree and determinative power between the achievement motive with the performance of teachers at the school amounted 0.773% or 77.3%, compensation for the school teachers in Manado is good enough. This result means that the compensation received is satisfactory, there is a linkage degree and determinative power between compensation and performance of the school teachers in Manado amounted to 0.582 or 58.2%.

  15. The influence of tyre characteristics on measures of rolling performance during cross-country mountain biking.

    Science.gov (United States)

    Macdermid, Paul William; Fink, Philip W; Stannard, Stephen R

    2015-01-01

    This investigation sets out to assess the effect of five different models of mountain bike tyre on rolling performance over hard-pack mud. Independent characteristics included total weight, volume, tread surface area and tread depth. One male cyclist performed multiple (30) trials of a deceleration field test to assess reliability. Further tests performed on a separate occasion included multiple (15) trials of the deceleration test and six fixed power output hill climb tests for each tyre. The deceleration test proved to be reliable as a means of assessing rolling performance via differences in initial and final speed (coefficient of variation (CV) = 4.52%). Overall differences between tyre performance for both deceleration test (P = 0.014) and hill climb (P = 0.032) were found, enabling significant (P < 0.0001 and P = 0.049) models to be generated, allowing tyre performance prediction based on tyre characteristics. The ideal tyre for rolling and climbing performance on hard-pack surfaces would be to decrease tyre weight by way of reductions in tread surface area and tread depth while keeping volume high.

  16. Does external technology acquisition determine export performance? Evidence from Chinese manufacturing firms

    DEFF Research Database (Denmark)

    Wang, Yuandi; Cao, Wei; Zhou, Zhao

    2013-01-01

    understanding of the determinants of export performance by examining the impact of the inter-organizational dimension of innovation strategy to export performance, which has been ignored in the prevailing “strategy tripod” perspective of exporting research. This study is based on a sample of 141 Chinese...... indigenous manufacturing firms that engaged in inward technology licensing between 2000 and 2003. The empirical results indicate that external technology acquisitions positively influence Chinese firms’ export performance. Moreover the exporting performance of using external technology varies depending...

  17. Performance of technology-driven simulators for medical students--a systematic review.

    Science.gov (United States)

    Michael, Michael; Abboudi, Hamid; Ker, Jean; Shamim Khan, Mohammed; Dasgupta, Prokar; Ahmed, Kamran

    2014-12-01

    Simulation-based education has evolved as a key training tool in high-risk industries such as aviation and the military. In parallel with these industries, the benefits of incorporating specialty-oriented simulation training within medical schools are vast. Adoption of simulators into medical school education programs has shown great promise and has the potential to revolutionize modern undergraduate education. An English literature search was carried out using MEDLINE, EMBASE, and psychINFO databases to identify all randomized controlled studies pertaining to "technology-driven" simulators used in undergraduate medical education. A validity framework incorporating the "framework for technology enhanced learning" report by the Department of Health, United Kingdom, was used to evaluate the capabilities of each technology-driven simulator. Information was collected regarding the simulator type, characteristics, and brand name. Where possible, we extracted information from the studies on the simulators' performance with respect to validity status, reliability, feasibility, education impact, acceptability, and cost effectiveness. We identified 19 studies, analyzing simulators for medical students across a variety of procedure-based specialities including; cardiovascular (n = 2), endoscopy (n = 3), laparoscopic surgery (n = 8), vascular access (n = 2), ophthalmology (n = 1), obstetrics and gynecology (n = 1), anesthesia (n = 1), and pediatrics (n = 1). Incorporation of simulators has so far been on an institutional level; no national or international trends have yet emerged. Simulators are capable of providing a highly educational and realistic experience for the medical students within a variety of speciality-oriented teaching sessions. Further research is needed to establish how best to incorporate simulators into a more primary stage of medical education; preclinical and clinical undergraduate medicine. Copyright © 2014 Elsevier Inc. All rights

  18. Educational Technology Research Journals: Performance Improvement Quarterly, 2001-2010

    Science.gov (United States)

    Mayer, Alisha Rasmussen; Francis, Jenifer; Harrison, J. Buckley; McPhillen, Ammon S.; West, Richard E.

    2012-01-01

    This article is an analysis of "Performance Improvement Quarterly" (PIQ) for the years 2001-2010. The intent was to examine the article types used, the authors who contributed the most to the journal, the topics the journal most commonly focused on, and the citation frequency of the journal's articles. The analysis revealed that…

  19. Modelling diffusion feedbacks between technology performance, cost and consumer behaviour for future energy-transport systems

    Science.gov (United States)

    Tran, Martino; Brand, Christian; Banister, David

    2014-04-01

    Emerging technologies will have important impacts on sustainability objectives. Yet little is known about the explicit feedbacks between consumer behaviour and technological change, and the potential impact on mass market penetration. We use the UK as a case-study to explore the dynamic interactions between technology supply, performance, cost, and heterogeneous consumer behaviour and the resulting influence on long term market diffusion. Simulations of competing vehicle technologies indicate that petrol hybrids (HEVs) dominate the market over the long-term because they benefit from improved performance and are able to reach the steep part of the diffusion curve by 2025 while competing technologies remain in the early stages of growth and are easier to displace in the market. This is due to the cumulative build-up of stock and slow fleet turnover creating inertia in the technological system. Consequently, it will be difficult to displace incumbent technologies because of system inertia, cumulative growth in stock, long operational life, and consumer risk aversion to new unproven technologies. However, when accounting for both technological and behavioural change, simulations indicate that if investment can reach 30-40% per annum growth in supply, combined with steady technology improvements, and more sophisticated agent decision making such as accounting for full technology lifecycle cost and performance, full battery electric vehicles could displace the incumbent system by 2050.

  20. How Do Board Characteristics Influence Business Performance? Evidence from Non-life Insurance Firms in Zimbabwe

    Directory of Open Access Journals (Sweden)

    Maxwell Sandada

    2015-08-01

    Full Text Available The purpose of this study was to contribute to the corporate governance literature by establishing the relationship between board characteristics and corporate performance within the nonlife insurance firms in Zimbabwe. The study sought to provide some insights on corporate governance since the phenomenon is relatively an emerging discipline in Zimbabwe. The paper sought to complement other corporate governance studies that were conducted in other environments by producing evidence on the phenomenon from a developing country context. A quantitative research approach was adopted and respondents were selected through a stratified random sampling. The results of the study confirm that board characteristics (board composition, diversity, and size exhibit a statistically significant positive predictive relationship with the performance of non-life insurance firms measured by gross premium written and customer retention. However, CEO/Chairman duality showed a negative relationship with business performance. Non-life insurance companies need to be cognizant of board characteristics in order to improve their performance. Moreover , the findings in this research has practical relevance for the selection process of directors as it highlights the importance of having a sizeable number of board members as well as an appropriate mix of competences and qualifications on the board. Although corporate governance is has been extensively researched, there is limited study in this area from a developing country like Zimbabwe with relatively less developed capital markets. It would be wrong to assume that the findings found in other countries can apply here because the conditions are different.

  1. Relationship of nurses' intrapersonal characteristics with work performance and caring behaviors: A cross-sectional study.

    Science.gov (United States)

    Geyer, Nelouise-Marié; Coetzee, Siedine K; Ellis, Suria M; Uys, Leana R

    2018-02-28

    This study aimed to describe intrapersonal characteristics (professional values, personality, empathy, and job involvement), work performance as perceived by nurses, and caring behaviors as perceived by patients, and to examine the relationships among these variables. A cross-sectional design was employed. A sample was recruited of 218 nurses and 116 patients in four private hospitals and four public hospitals. Data were collected using self-report measures. Data analysis included descriptive statistics, exploratory and confirmatory factor analyses, hierarchical linear modelling, correlations, and structural equation modeling. Nurses perceived their work performance to be of high quality. Among the intrapersonal characteristics, nurses had high scores for professional values, and moderately high scores for personality, empathy and job involvement. Patients perceived nurses' caring behaviors as moderately high. Professional values of nurses were the only selected intrapersonal characteristic with a statistically significant positive relationship, of practical importance, with work performance as perceived by nurses and with caring behaviors as perceived by patients at ward level. Managers can enhance nurses' work performance and caring behaviors through provision of in-service training that focuses on development of professional values. © 2018 John Wiley & Sons Australia, Ltd.

  2. Physico-chemical characteristics of high performance polymer modified by low and atmospheric pressure plasma

    International Nuclear Information System (INIS)

    Bhatnagar, Nitu; Sangeeta, Jha; Bhowmik, Shantanu; Gupta, Govind; Moon, J.B.; Kim, C.G.

    2012-01-01

    In this work, the effect of low pressure plasma and atmospheric p ressure plasma treatment on surface properties and adhesion characteristics of high performance polymer, Polyether Ether Ketone (PEEK) are investigated in terms of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Atomic Force Microscopy (AFM). The experimental results show that the PEEK surface treated by atmospheric pressure plasma lead to an increase in the polar component of the surface energy, resulting in improving the adhesion characteristics of the PEEK/Epoxy adhesive system. Also, the roughness of the treated surfaces is largely increased as confirmed by AFM observation. These results can be explained by the fact that the atmospheric pressure plasma treatment of PEEK surface yields several oxygen functionalities on hydrophobic surface, which play an important role in increasing the surface polarity, wettability, and the adhesion characteristics of the PEEK/Epoxy adhesive system. (authors)

  3. Characteristics Buton Natural Asphalt-Rubber (BNA-R on the Performance Improvement of Warm Mix Asphalt Using Natural Zeolite

    Directory of Open Access Journals (Sweden)

    Wahjuningsih Nurul

    2018-01-01

    Full Text Available The decrease in the ability of service of pavement can be caused by the durability factor in the pavement layer in receiving heavy traffic load and the temperature of the pavement. Permanent deformation is one of the criteria of failure of asphalt mixture. Performance assessment of the asphalt mixture can be observed from the rheological properties of asphalt binder. The use of BNA-R in this study is intended to modify the characteristics of bitumen penetration grade 60 / 70 used in warm mix asphalt. Warm mix asphalt with lower temperatures of mixing and compaction than conventional asphalt mixtures was chosen because it is more environmentally friendly. To reduce the temperature in this warm asphalt technology is achieved by using natural zeolite. Both of these materials are local materials that are widely available in Indonesia. The rheology of asphalt 60/70 modified with BNA-R indicates that the addition of BNA-R in the base asphalt increase the complex modulus value and decrease the phase angle value. These values were related to the performance of mixture in the permanent deformation criteria. Reducing the temperature of mixing and compaction should be balanced with modifying the asphalt binder used. Rutting due to permanent deformation can resulted in inconvenience to the passengers and can lead to high costs of road maintenance. To determine the permanent deformation of asphalt mix with material combinations was performed through the wheel tracking test machine with 3,780 cycles for 3 hours. The results shows that after test track over 7 thousand passes have seen permanent deformation characteristics of asphalt concrete mixture with a variation of the characteristics of bitumen.

  4. Characteristics Buton Natural Asphalt-Rubber (BNA-R) on the Performance Improvement of Warm Mix Asphalt Using Natural Zeolite

    Science.gov (United States)

    Wahjuningsih, Nurul; Pranowo Hadiwardoyo, Sigit; Jachrizal Sumabrata, R.

    2018-03-01

    The decrease in the ability of service of pavement can be caused by the durability factor in the pavement layer in receiving heavy traffic load and the temperature of the pavement. Permanent deformation is one of the criteria of failure of asphalt mixture. Performance assessment of the asphalt mixture can be observed from the rheological properties of asphalt binder. The use of BNA-R in this study is intended to modify the characteristics of bitumen penetration grade 60 / 70 used in warm mix asphalt. Warm mix asphalt with lower temperatures of mixing and compaction than conventional asphalt mixtures was chosen because it is more environmentally friendly. To reduce the temperature in this warm asphalt technology is achieved by using natural zeolite. Both of these materials are local materials that are widely available in Indonesia. The rheology of asphalt 60/70 modified with BNA-R indicates that the addition of BNA-R in the base asphalt increase the complex modulus value and decrease the phase angle value. These values were related to the performance of mixture in the permanent deformation criteria. Reducing the temperature of mixing and compaction should be balanced with modifying the asphalt binder used. Rutting due to permanent deformation can resulted in inconvenience to the passengers and can lead to high costs of road maintenance. To determine the permanent deformation of asphalt mix with material combinations was performed through the wheel tracking test machine with 3,780 cycles for 3 hours. The results shows that after test track over 7 thousand passes have seen permanent deformation characteristics of asphalt concrete mixture with a variation of the characteristics of bitumen.

  5. Transformational leadership and safety performance among nurses: the mediating role of knowledge-related job characteristics.

    Science.gov (United States)

    Lievens, Ilse; Vlerick, Peter

    2014-03-01

    To report the impact of transformational leadership on two dimensions of nurses' safety performance (i.e. safety compliance and safety participation) and to study the mediating role of knowledge-related job characteristics in this relationship. Safety performance refers to the behaviours that employees exhibit to adhere to safety guidelines and to promote health and safety at their workplace. Nurses' safety performance is a major challenge for healthcare settings, urging the need to identify the key determinants and psychological mechanisms that influence it. A cross-sectional survey study. The study was carried out in September 2010 in a large Belgian hospital. We used self-administered questionnaires; 152 nurses participated. The hypotheses were tested using hierarchical regression analyses. In line with our first hypothesis, the results show that transformational leadership exerted a significant positive impact on both dimensions of nurses' safety performance. This positive relation was mediated by knowledge-related job characteristics, supporting our second hypothesis. Head nurses' transformational leadership can enhance nurses' compliance with and participation in safety. Furthermore, transformational head nurses are able to influence the perception that their nurses have about the kind and amount of knowledge in their job, which can also lead to increases in both dimensions of nurses' safety performance. This study therefore demonstrates the key impact that transformational head nurses have, both directly and indirectly, on the safety performance of their nurses. © 2013 John Wiley & Sons Ltd.

  6. Performance characteristics and parametric optimization of an irreversible magnetic Ericsson heat-pump

    International Nuclear Information System (INIS)

    Wei Fang; Lin Guoxing; Chen Jincan; Brueck, Ekkes

    2011-01-01

    Taking into account the finite-rate heat transfer in the heat-transfer processes, heat leak between the two external heat reservoirs, regenerative loss, regeneration time, and internal irreversibility due to dissipation of the cycle working substance, an irreversible magnetic Ericsson heat-pump cycle is presented. On the basis of the thermodynamic properties of magnetic materials, the performance characteristics of the irreversible magnetic Ericsson heat-pump are investigated and the relationship between the optimal heating load and the coefficient of performance (COP) is derived. Moreover, the maximum heating load and the corresponding COP as well as the maximum COP and the corresponding heating load are obtained. Furthermore, the other optimal performance characteristics are discussed in detail. The results obtained here may provide some new information for the optimal parameter design and the development of real magnetic Ericsson heat-pumps. -- Research Highlights: →The effects of multi-irreversibilities on the performance of a magnetic heat-pump are revealed. →Mathematical expressions of the heating load and the COP are derived and the optimal performance and operating parameters are analyzed and discussed. →Several important performance bounds are determined.

  7. Effects of Selected Corporate Governance Characteristics on Firm Performance: Empirical Evidence from Kenya

    Directory of Open Access Journals (Sweden)

    Vincent Okoth Ongore

    2011-01-01

    Full Text Available This paper examines the interrelations among ownership, board and manager characteristics and firm performance in a sample of 54 firms listed at the Nairobi Stock Exchange (NSE. These governance characteristics, designed to minimize agency problems between principals and agents are operationalized in terms of ownership concentration, ownership identity, board effectiveness and managerial discretion. The typical ownership identities at the NSE are government, foreign, institutional, manager and diverse ownership forms. Firm performance is measured using Return on Assets (ROA, Return on Equity (ROE and Dividend Yield (DY. Using PPMC, Logistic Regression and Stepwise Regression, the paper presents evidence of significant positive relationship between foreign, insider, institutional and diverse ownership forms, and firm performance. However, the relationship between ownership concentration and government, and firm performance was significantly negative. The role of boards was found to be of very little value, mainly due to lack of adherence to board member selection criteria. The results also show significant positive relationship between managerial discretion and performance. Collectively, these results are consistent with pertinent literature with regard to the implications of government, foreign, manager (insider and institutional ownership forms, but significantly differ concerning the effects of ownership concentration and diverse ownership on firm performance.

  8. SELECTION OF ENDOCRINOLOGY SUBSPECIALTY TRAINEES: WHICH APPLICANT CHARACTERISTICS ARE ASSOCIATED WITH PERFORMANCE DURING FELLOWSHIP TRAINING?

    Science.gov (United States)

    Natt, Neena; Chang, Alice Y; Berbari, Elie F; Kennel, Kurt A; Kearns, Ann E

    2016-01-01

    To determine which residency characteristics are associated with performance during endocrinology fellowship training as measured by competency-based faculty evaluation scores and faculty global ratings of trainee performance. We performed a retrospective review of interview applications from endocrinology fellows who graduated from a single academic institution between 2006 and 2013. Performance measures included competency-based faculty evaluation scores and faculty global ratings. The association between applicant characteristics and measures of performance during fellowship was examined by linear regression. The presence of a laudatory comparative statement in the residency program director's letter of recommendation (LoR) or experience as a chief resident was significantly associated with competency-based faculty evaluation scores (β = 0.22, P = .001; and β = 0.24, P = .009, respectively) and faculty global ratings (β = 0.85, P = .006; and β = 0.96, P = .015, respectively). The presence of a laudatory comparative statement in the residency program director's LoR or experience as a chief resident were significantly associated with overall performance during subspecialty fellowship training. Future studies are needed in other cohorts to determine the broader implications of these findings in the application and selection process.

  9. Modern control technology for improved nuclear reactor performance

    International Nuclear Information System (INIS)

    Oakes, L.C.

    1986-01-01

    One of the main complaints leveled at reactor control systems by utility spokesmen is complexity. One only has to look inside a power reactor control room to appreciate this viewpoint. The high reliability and versatility of modern microprocessors makes possible distributed control systems with only performance data and abnormal conditions being relayed to the control room. In a sense, this emulates the human-body control system where routine repetitive actions are handled in an involuntary manner. The significance of expert systems to the nuclear reactor control and safety systems is their ability to capture human and other expertise and make it available, upon demand, and under almost all circumstances. Thus, human problem-solving skills acquired by the learning process over a long period of time can be captured and employed with the reliability inherent in computers. This is especially important in nuclear plants when human operators are burdened by stress and emotional factors that have a dramatic effect on performance level

  10. submitter Performance studies of CMS workflows using Big Data technologies

    CERN Document Server

    Ambroz, Luca; Grandi, Claudio

    At the Large Hadron Collider (LHC), more than 30 petabytes of data are produced from particle collisions every year of data taking. The data processing requires large volumes of simulated events through Monte Carlo techniques. Furthermore, physics analysis implies daily access to derived data formats by hundreds of users. The Worldwide LHC Computing Grid (WLCG) - an international collaboration involving personnel and computing centers worldwide - is successfully coping with these challenges, enabling the LHC physics program. With the continuation of LHC data taking and the approval of ambitious projects such as the High-Luminosity LHC, such challenges will reach the edge of current computing capacity and performance. One of the keys to success in the next decades - also under severe financial resource constraints - is to optimize the efficiency in exploiting the computing resources. This thesis focuses on performance studies of CMS workflows, namely centrallyscheduled production activities and unpredictable d...

  11. Health care interprofessional education: encouraging technology, teamwork, and team performance.

    Science.gov (United States)

    2014-04-01

    It is critical to prepare nurses for future practice to work in teams by engaging students in interprofessional education (IPE) that fosters positive attitudes toward teamwork. The purpose of this study was to examine the effects of computer-supported IPE on students’ attitudes and perceptions toward health care teamwork and team performance. A hybrid approach to IPE was used to provide students with an educational experience that combined the benefits of traditional face-to-face communication methodology with a computer-mediated platform that focused on reflection and team building. A statistically significant difference was found in students’ perceptions of team performance after engaging in computer-supported IPE. No statistically significant difference in students’ pretest–posttest composite attitude toward teamwork scores was noted; however, there was a positive trend toward improved scores.

  12. Technology and Real Estate Brokerage Firm Financial Performance

    OpenAIRE

    John D. Benjamin; Peter Chinloy; Donald Jud; Daniel T. Winkler

    2005-01-01

    This study investigates the impact of Internet usage on the financial performance of residential real estate brokerage firms using a database of over 1,700 observations. Factor loadings and a factor score for Internet usage are developed. The results show that Internet use is positively related to revenue and net income, and negatively related to net margin. In a second stage analysis, Internet use is found to be positively associated with franchise affiliation, affiliation with a referral /r...

  13. Study of performance and emission characteristics of a partially coated LHR SI engine blended with n-butanol and gasoline

    Directory of Open Access Journals (Sweden)

    Nitesh Mittal

    2013-09-01

    Full Text Available To meet the present requirements of the automotive industry, there is continuous search to improve the performance, exhaust emission, and life of the IC engines. The meet the first two challenges, researchers are working both on newer engine technologies and fuels. Some of the published work indicates that coating on the combustion surface of the engine with ceramic material results in improved performance and reduced emission levels when fueled with alternate fuel blended fuels, and this serves as a base for this work. Normal-Butanol has molecular structure that is adaptable to gasoline, and it is considered as one of the alternative fuels for SI engines. Blending butanol with gasoline changes the properties of the fuel and alters the engine performance and emission characteristics. This is because heat which is released at a rate as a result of combustion of the compressed air–fuel mixture in the combustion chamber gets changed with respect to change fuel properties, air fuel ratio, and engine speed. An experimental investigation is carried out on a partially insulated single cylinder SI engine to study the performance and emission characteristics when fueled with two different blends of butanol and gasoline. The cylinder head surface and valves are coated with a ceramic material consisting of Zirconium dioxide (ZrO2 with 8% by weight of Yttrium Oxide (Y2O3 to a thickness of 0.3 mm by plasma spray method. Two different fuel blends containing 10% and 15% by volume of butanol in Gasoline are tested on an engine dynamometer using the uncoated and ceramic coated engines. The results strongly indicate that combination of ceramic coated engine and butanol gasoline blended fuel has potential to improve the engine performance.

  14. Numerical study of influence of biofuels on the combustion characteristics and performance of aircraft engine system

    International Nuclear Information System (INIS)

    Zhou, Li; Liu, Zeng-wen; Wang, Zhan-xue

    2015-01-01

    The atomization and combustion flowfield of the combustion chamber with swirl-nozzle were simulated using different biofuels; the thermodynamic cycle of the aircraft engine system were also analyzed, influences of biofuels on the combustion characteristics and performance of aircraft engine system were explored. Results show that viscosity and caloric value are key factors affecting the atomization and combustion characteristics of biofuels, and then dominate the distribution of the temperature and NO concentration. Due to the characteristic of low viscosity and low caloric value for biofuels adopted, the biofuels accumulate near the head of combustion chamber, and the corresponding NO emission is lower than that it has for conventional kerosene. When biofuels with low caloric value are used under the operation condition which is same as the condition for the conventional kerosene, lower turbine inlet temperature, lower thrust and higher specific fuel consumption would be achieved for the aircraft engine. - Highlights: • Influences of biofuels properties on combustion characteristic are explored. • Effects of biofuels on cycle parameters of aircraft engine are discussed. • Viscosity and caloric value are key factors affecting combustion of biofuels. • NO emission becomes lower when biofuels with low caloric value is adopted. • The performance of aircraft engine becomes worse for biofuels with low caloric value.

  15. Performance-Based Technology Selection Filter description report. INEL Buried Waste Integrated Demonstration System Analysis project

    Energy Technology Data Exchange (ETDEWEB)

    O`Brien, M.C.; Morrison, J.L.; Morneau, R.A.; Rudin, M.J.; Richardson, J.G.

    1992-05-01

    A formal methodology has been developed for identifying technology gaps and assessing innovative or postulated technologies for inclusion in proposed Buried Waste Integrated Demonstration (BWID) remediation systems. Called the Performance-Based Technology Selection Filter, the methodology provides a formalized selection process where technologies and systems are rated and assessments made based on performance measures, and regulatory and technical requirements. The results are auditable, and can be validated with field data. This analysis methodology will be applied to the remedial action of transuranic contaminated waste pits and trenches buried at the Idaho National Engineering Laboratory (INEL).

  16. Technology, Demographic Characteristics and E-Learning Acceptance: A Conceptual Model Based on Extended Technology Acceptance Model

    Science.gov (United States)

    Tarhini, Ali; Elyas, Tariq; Akour, Mohammad Ali; Al-Salti, Zahran

    2016-01-01

    The main aim of this paper is to develop an amalgamated conceptual model of technology acceptance that explains how individual, social, cultural and organizational factors affect the students' acceptance and usage behaviour of the Web-based learning systems. More specifically, the proposed model extends the Technology Acceptance Model (TAM) to…

  17. Talent in Female Gymnastics: a Survival Analysis Based upon Performance Characteristics.

    Science.gov (United States)

    Pion, J; Lenoir, M; Vandorpe, B; Segers, V

    2015-11-01

    This study investigated the link between the anthropometric, physical and motor characteristics assessed during talent identification and dropout in young female gymnasts. 3 cohorts of female gymnasts (n=243; 6-9 years) completed a test battery for talent identification. Performance-levels were monitored over 5 years of competition. Kaplan-Meier and Cox Proportional Hazards analyses were conducted to determine the survival rate and the characteristics that influence dropout respectively. Kaplan-Meier analysis indicated that only 18% of the female gymnasts that passed the baseline talent identification test survived at the highest competition level 5 years later. The Cox Proportional Hazards Model indicated that gymnasts with a score in the best quartile for a specific characteristic significantly increased chances of survival by 45-129%. These characteristics being: basic motor skills (129%), shoulder strength (96%), leg strength (53%) and 3 gross motor coordination items (45-73%). These results suggest that tests batteries commonly used for talent identification in young female gymnasts may also provide valuable insights into future dropout. Therefore, multidimensional test batteries deserve a prominent place in the selection process. The individual test results should encourage trainers to invest in an early development of basic physical and motor characteristics to prevent attrition. © Georg Thieme Verlag KG Stuttgart · New York.

  18. Summary performance assessment of in situ remediation technologies demonstrated at Savannah River

    International Nuclear Information System (INIS)

    Rosenberg, N.D.; Robinson, B.A.; Birdsell, K.H.; Travis, B.J.

    1994-06-01

    The Office of Technology Development (OTD) in the Department of Energy's (DOE) Office of Environmental Restoration and Waste Management is investigating new technologies for ''better, faster, cheaper, safer'' environmental remediation. A program at DOE's Savannah River site was designed to demonstrate innovative technologies for the remediation of volatile organic compounds (VOCs) at nonarid sites. Two remediation technologies, in situ air stripping and in situ bioremediation--both using horizontal wells, were demonstrated at the site between 1990--1993. This brief report summarizes the conclusions from three separate modeling studies on the performance of these technologies

  19. Use of information technology for medication management in residential care facilities: correlates of facility characteristics.

    Science.gov (United States)

    Bhuyan, Soumitra S; Chandak, Aastha; Powell, M Paige; Kim, Jungyoon; Shiyanbola, Olayinka; Zhu, He; Shiyanbola, Oyewale

    2015-06-01

    The effectiveness of information technology in resolving medication problems has been well documented. Long-term care settings such as residential care facilities (RCFs) may see the benefits of using such technologies in addressing the problem of medication errors among their resident population, who are usually older and have numerous chronic conditions. The aim of this study was two-fold: to examine the extent of use of Electronic Medication Management (EMM) in RCFs and to analyze the organizational factors associated with the use of EMM functionalities in RCFs. Data on RCFs were obtained from the 2010 National Survey of Residential Care Facilities. The association between facility, director and staff, and resident characteristics of RCFs and adoption of four EMM functionalities was assessed through multivariate logistic regression. The four EMM functionalities included were maintaining lists of medications, ordering for prescriptions, maintaining active medication allergy lists, and warning of drug interactions or contraindications. About 12% of the RCFs adopted all four EMM functionalities. Additionally, maintaining lists of medications had the highest adoption rate (34.5%), followed by maintaining active medication allergy lists (31.6%), ordering for prescriptions (19.7%), and warning of drug interactions or contraindications (17.9%). Facility size and ownership status were significantly associated with adoption of all four EMM functionalities. Medicaid certification status, facility director's age, education and license status, and the use of personal care aides in the RCF were significantly associated with the adoption of some of the EMM functionalities. EMM is expected to improve the quality of care and patient safety in long-term care facilities including RCFs. The extent of adoption of the four EMM functionalities is relatively low in RCFs. Some RCFs may strategize to use these functionalities to cater to the increasing demands from the market and also to

  20. Mobile technology use and desired technology-based intervention characteristics among HIV+ Black men who have sex with men.

    Science.gov (United States)

    Senn, Theresa E; Braksmajer, Amy; Coury-Doniger, Patricia; Urban, Marguerite A; Carey, Michael P

    2017-04-01

    HIV positive Black men who have sex with men (MSM) are retained in HIV medical care at suboptimal rates. Interventions targeted to Black MSM are needed to help to improve their retention in care. The purposes of this study were to investigate the use of mobile technology among HIV+ Black MSM and to explore participants' thoughts about the use of mobile technology for HIV retention in care interventions. Twenty-two HIV+ Black MSM completed a technology use survey and participated in a qualitative interview regarding technology-based interventions. The majority of participants (95%) had access to a cell phone, and used their phones frequently (median 3 hours/day). Men preferred interventions that would allow for anonymous participation and that would provide individually tailored support. Mobile technology is a promising approach to intervention delivery for both younger and older HIV+ Black MSM. These interventions should incorporate features that are desirable to men (i.e., anonymous participation and individual tailoring).

  1. Evaluation of the performance characteristic for mammography by using edge device

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Won [Dept. of Radiology, Kyung Hee University Hospital at Gang-dong, Seoul (Korea, Republic of); Choi, Jwan Woo [Dept. of Radiology, Asan Medical Center, Seoul (Korea, Republic of); Jeong, Hoi Woun [Dept. of Radiological Technology, The Baekseok Culture University, Cheonan (Korea, Republic of); Jang, Seo Goo [Dept. of Medical Science, The Soonchunhyang University, Asan (Korea, Republic of); Lee, Eul Kyu [Dept. of Radiology, Inje Paik University Hospital Jeo-dong, Seoul (Korea, Republic of); Son, Soon Yong [Dept. of Radiological Technology, The Wonkwang Health Science University, Iksan (Korea, Republic of); Son, Jin Hyun; Min, Jung Whan [Dept. of Radiological Technology, The Shingu University, Sungnam (Korea, Republic of)

    2016-09-15

    The purpose of this study was to evaluation of the performance characteristic for mammography by using edge device that mammography equipment improves essential in the correct diagnosis for the maintenance. We measured the modulation transfer function (MTF), the noise power spectrum (NPS), and the detective quantum efficiency (DQE) using the 61267 RQA-M2 based on commission standard international electro-technical commission (IEC). As a results, spatial resolution of dimensions tomo and lorad selenia mammography were maintained at 10 mm-1 and NPS and DQE including the low nyquist frequency indicated to 6.0 mm-1. Therefore, regularly QA of mammography system should be necessary. This study can be contribute to evaluate QA for performance characteristic of mammography of DDR system.

  2. Design characteristics of metallic fuel rod on its in-LMR performance

    International Nuclear Information System (INIS)

    Hwang, Woan; Kang Hee Young; Nam, Cheol; Kim, Jong Oh

    1997-01-01

    Fuel design is a key feature to assure LMR safety goals. To date, a large effort had been devoted to develop metallic fuels at ANL's experimental breeder reactor (EBR-II). The major design and performance parameters investigated include; thermal conductivity and temperature profile; smear density; axial plenum; FCMI and cladding deformation including creep, and fission gas release. In order to evaluate the sensitivity of each parameter, in-LMR performances of metallic fuels are not only reviewed by the experiment results in literatures, but also key design characteristics according to the variation of metallic fuel rod design parameters are analyzed by using the MACSIS code which simulates in-reactor behaviors of metal fuel rod. In this study, key design characteristics and the criteria which must be considered to design fuel rod in LMR, are proposed and discussed. (author). 14 refs., 4 figs

  3. Innovative technologies of waste recycling with production of high performance products

    International Nuclear Information System (INIS)

    Gilmanshin, R; Azimov, Yu I; Gilmanshina, S I; Ferenets, A V; Galeeva, A I

    2015-01-01

    The innovative ways of recycling wastes as a tool for sustainable development are presented in the article. The technology of the production of a composite material based on the rubber fiber composite waste tire industry is presented. The results of experimental use of the products in the real conditions. The comparative characteristics of the composite material rubber fiber composite are given. The production technology of construction and repairing materials on the basis of foamed glass is presented. (paper)

  4. Innovative technologies of waste recycling with production of high performance products

    Science.gov (United States)

    Gilmanshin, R.; Ferenets, A. V.; Azimov, Yu I.; Galeeva, A. I.; Gilmanshina, S. I.

    2015-06-01

    The innovative ways of recycling wastes as a tool for sustainable development are presented in the article. The technology of the production of a composite material based on the rubber fiber composite waste tire industry is presented. The results of experimental use of the products in the real conditions. The comparative characteristics of the composite material rubber fiber composite are given. The production technology of construction and repairing materials on the basis of foamed glass is presented.

  5. A study on the establishment of component/equipment performance criteria considering Heavy Water Reactor characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Keun Sun; Kwon, Young Chul; Lee, Min Kyu; Lee, Yun Soo [Sunmoon Univ., Asan (Korea, Republic of); Chang, Seong Hoong; Ryo, Chang Hyun [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Kim, Soong Pyung; Hwnag, Jung Rye; Chung, Chul Kee [Chosun Univ., Gwangju (Korea, Republic of)

    2002-03-15

    Foreign and domestic technology trends, regulatory requirements, design and researches for heavy water reactors are analyzed. Safety design guides of Canada industry and regulatory documents and consultative documents of Canada regulatory agency are reviewed. Applicability of MOST guidance 16 Revision 'guidance for technical criteria of nuclear reactor facility' is reviewed. Specific performance criteria are established for components and facilities for heavy water reactor.

  6. The impact of ownership and other corporate characteristics on performance of V4 companies

    Directory of Open Access Journals (Sweden)

    David Procházka

    2017-06-01

    Full Text Available The objective of this paper is to assess financial performance of Czech, Hungarian, Polish, and Slovak unlisted companies. The sample retrieved from the Amadeus database contains 171,095 firm-year observations for the period of 2010-2014. A linear regression model (weighted least squares with robust correction for standard errors is run to regress Return on Assets (ROA as the dependent variable against selected entity-specific factors, including ownership characteristics. Empirical evidence uncovers several findings. Firstly, the performance of V4 companies is comparable except for Hungary, where companies report lower ROA on average. Secondly, firms established after the failure of communist regimes outperform the privatised companies. Thirdly, the ownership characteristics do matter. Having domestic owners is not a disadvantage, as only the companies with controlling shareholders from the Anglo-Saxon countries perform better. Other jurisdictions of parents lead either to comparable (e.g., old EU members, developed Asian countries or even worse (e.g., new EU members, post-Soviet bloc performance as compared to domestic ownership. Similarly, family firms perform significantly better than the companies controlled by institutional owners or by public sector, but worse than the firms controlled by financial institutions. The listing status of a parent is not an influential factor of performance. Fourthly, the size of a company also matters, as small enterprises report better performance in their financial statements than medium and large undertakings. Fifthly, higher leverage undermines performance. Finally, there is a wide dispersion in average performance across the industries. The study results might be relevant for policy makers while choosing between direct and indirect support for diverse types of businesses.

  7. Physical Characteristics and Performance of Japanese Top-Level American Football Players.

    Science.gov (United States)

    Yamashita, Daichi; Asakura, Masaki; Ito, Yoshihiko; Yamada, Shinzo; Yamada, Yosuke

    2017-09-01

    Yamashita, D, Asakura, M, Ito, Y, Yamada, S, and Yamada, Y. Physical characteristics and performance of Japanese top-level American football players. J Strength Cond Res 31(9): 2455-2461, 2017-This study aimed to compare the physical characteristics and performance between top-level nonprofessional football players in Japan and National Football League (NFL) Combine invited players and between top-level and middle-level players in Japan to determine the factors that enhance performance in international and national competitions. A total of 168 American football players (>20 years) in Japan participated in an anthropometric (height and weight) and physical (vertical jump, long jump, 40-yard dash, pro-agility shuttle, 3-cone drill, and bench press repetition test) measurement program based on the NFL Combine program to compete in the selection of candidates for the Senior World Championship. All players were categorized into 1 of the 3 position groups based on playing position: skill players, big skill players, and linemen. Japanese players were additionally categorized into selected and nonselected players for the second tryout. The NFL Combine candidates had significantly better performance than selected Japanese players on all variables except on performance related to quickness among the 3 position groups. Compared with nonselected players, selected Japanese skill players had better performance in the 40-yard dash and bench press test and big skill players had better performance in the vertical jump, broad jump, and 40-yard dash. Selected and nonselected Japanese linemen were not different in any measurements. These results showed the challenges in American football in Japan, which include not only improving physical performance of top-level players, but also increasing the number of football players with good physical performance.

  8. Description and performance characteristics for the neutron Coincidence Collar for the verification of reactor fuel assemblies

    International Nuclear Information System (INIS)

    Menlove, H.O.

    1981-08-01

    An active neutron interrogation method has been developed for the measurement of 235 U content in fresh fuel assemblies. The neutron Coincidence Collar uses neutron interrogation with an AmLi neutron source and coincidence counting the induced fission reaction neutrons from the 235 U. This manual describes the system components, operation, and performance characteristics. Applications of the Coincidence Collar to PWR and BWR types of reactor fuel assemblies are described

  9. Co-crystallization: An approach to improve the performance characteristics of active pharmaceutical ingredients

    OpenAIRE

    Jignasa Ketan Savjani

    2015-01-01

    Co-crystal chemistry has recently attracted supramolecular scientists. Co-crystals are comprising of hydrogen boding assembly between different molecules. Many issues related to performance characteristics of an active pharmaceutical ingredient (API) can be resolved using co-crystallization approach. Proper understanding of crystal structure of an API is required for successful formation of co-crystals with the selected co-former. This review article focus on explanation about co-crystals, in...

  10. Board of Directors, Audit Committee Characteristics and the Performance of Saudi Arabia Listed Companies

    OpenAIRE

    Al-Matari, Yahya Ali; Al-Swidi, Abdullah Kaid; Fadzil, Faudziah Hanim Bt Hanim; Al-Matari, Ebrahim Mohammed

    2012-01-01

    This study examines the relationship between the internal corporate governance mechanism related to the board of directors, the audit committee characteristics and the performance of the Saudi companies listed in the Saudi stock exchange (TADAWL) in 2010, excluding financial companies. The statistical results of the study are not in line with the agency theory that board of directors and audit committee might mitigate agency problems leading to reduced agency cost by aligning the interests of...

  11. Board of Directors, Audit Committee Characteristics and Performance of Saudi Arabia Listed Companies

    OpenAIRE

    Yahya Ali Al-Matari; Abdullah Kaid Al-Swidi; Faudziah Hanim Bt Fadzil; Ebrahim Mohammed Al-Matari

    2012-01-01

    This study examines the relationship between the internal corporate governance mechanism related to the board of directors, the audit committee characteristics and the performance of the Saudi companies listed in the Saudi stock exchange (TADAWL) in 2010, excluding financial companies. The statistical results of the study are not in line with the agency theory that board of directors and audit committee might mitigate agency problems leading to reduced agency cost by aligning the interests of...

  12. Performance Characteristics and Prediction of Bodyweight using Linear Body Measurements in Four Strains of Broiler Chicken

    OpenAIRE

    I. Udeh; J.O. Isikwenu and G. Ukughere

    2011-01-01

    The objectives of this study were to compare the performance characteristics of four strains of broiler chicken from 2 to 8 weeks of age and predict body weight of the broilers using linear body measurements. The four strains of broiler chicken used were Anak, Arbor Acre, Ross and Marshall. The parameters recorded were bodyweight, weight gain, total feed intake, feed conversion ratio, mortality and some linear body measurements (body length, body width, breast width, drumstick length, shank l...

  13. Windmilling of turbofan engine; calculation of performance characteristics of a turbofan engine under windmilling

    OpenAIRE

    Ramanathan, A.

    2014-01-01

    The turbofan is a type of air breathing jet engine that finds wide use in aircraft propulsion. During the normal operation of a turbofan engine installed in aircraft, the combustor is supplied with fuel, flow to the combustor is cut off and the engine runs under so called Windmilling conditions being driven only by the ram pressure ratio by producing drag. In-depth analysis is done to study the performance characteristics at this state.

  14. Effect of Engine Modifications on Performance and Emission Characteristics of Diesel Engines with Alternative Fuels

    OpenAIRE

    Venkateswarlu, K.; Murthy, B.S.R

    2010-01-01

    Performance and emission characteristics unmodified diesel engines operating on different alternative fuels with smaller blend proportions are comparable with pure diesel operation. But with increased blend proportions due to the associated problems of vegetable oils like high viscosity and low volatility pollution levels increase which however is accompanied by operating and durability problems with the long term usage of engine. This paper discusses the necessary modifications required to o...

  15. Usage of performance measurement and evaluation systems : the impact of evaluator characteristics

    OpenAIRE

    Gelderman, Maarten

    1998-01-01

    This paper discusses the relation between characteristics of the evaluating manager and the way performance measurement and evaluation information is used. First a discussion is provided about the dependent variable. It is recognized that categorization into archetypes (e.g., evaluative styles) is unsatisfactory. Instead the information content/emphasis dimensions financial-non- financial, quantitative-qualitative, process-outcome, past-future and external-internal, along with the dimension f...

  16. An experimental study on performance and emission characteristics of a hydrogen fuelled spark ignition engine

    OpenAIRE

    Kahraman, Erol; Özcanlı, Şevket Cihangir; Özerdem, Barış

    2007-01-01

    In the present paper, the performance and emission characteristics of a conventional four cylinder spark ignition (SI) engine operated on hydrogen and gasoline are investigated experimentally. The compressed hydrogen at 20 MPa has been introduced to the engine adopted to operate on gaseous hydrogen by external mixing. Two regulators have been used to drop the pressure first to 300 kPa, then to atmospheric pressure. The variations of torque, power, brake thermal efficiency, brake mean effectiv...

  17. Performance Characteristics of Hero's Turbine Using Hot Water as a Working Fluid

    OpenAIRE

    FUJII, Terushige; OHTA, Jun-ichi; AKAGAWA, Koji; NAKAMURA, Toshi; ASANO, Hitoshi

    1992-01-01

    From the viewpoint of energy conservation and the development of new energy resources,it is important to utilize geothermal resources and waste heat from factories. Among energy conversion device,there is a radial outflow reaction turbine,i.e.,Hero's turbine. Performance characteristics of Hero's turbine are analytically and experimentally clarified for flashing expansion of initially subcooled hot water. It is found that: (a)there is an optimum number of revolutions at which maximum tubine e...

  18. Performance Characteristics of Hero's Turbine Using Hot Water as a Working Fluid

    OpenAIRE

    藤井, 照重; 太田, 淳一; 赤川, 浩爾; 中村, 登志; 浅野, 等

    1990-01-01

    From the view point of energy saving and the development of new energy resources,it is important to utilize geothermal resources and waste heat from factories. As one of the energy conversion expanders,there is a radial outflow reaction turbine(that is,Hero's turbine). Performance characteristics of Hero's turbine using subcooled hot water as a working fluid are clarified analytically and experimentally. It is found that:(a)there is an optimum rotational speed at which maximum turbine efficie...

  19. INFLUENCE OF POLYMERIC-DISPERSED REINFORCEMENT ADDITIVES ON THE PERFORMANCE CHARACTERISTICS OF ASPHALT CONCRETE

    Directory of Open Access Journals (Sweden)

    Chernov Sergey Anatolevych

    2017-07-01

    Full Text Available The technique and results of the studies of the influence of a polymeric-dispersed reinforcement additive on the performance characteristics of road hot asphalt concrete, namely, its resistance to fatigue failures, rutting and development of residual deformation are described. It is shown that the proposed method of modification of asphalt-concrete mixtures ensures an increase in the durability of layers of pavement road surface.

  20. Kinanthropometric and performance characteristics of elite and non-elite female softball players.

    Science.gov (United States)

    Singh, S; Singh, M; Rathi, B

    2013-12-01

    The purpose of the present study was to compare the kinanthropometric and performance characteristics of elite and non-elite female softball players. A total forty elite and non-elite level female softball players were selected from the different colleges affiliated to the Guru Nanak Dev University, Amritsar, for the present study. The height of subjects was measured by using the standard anthropometric rod. Weight was measured with portable weighing machine. Widths and diameters of body parts were measured by using digital caliper. Girths and lengths were taken with steel tape. Skinfold thickness measurements were taken using the Slimguide skinfold caliper. All subjects were also assessed for performance tests i.e. vertical jump, 50m sprint, medicine ball throw, 10×4m shuttle run and reaction time. Independent samples t-test reveals that elite female softball players were significantly taller (Psoftball players also had significantly greater biacromial (Psoftball players. The non-elite female softball players were found to have significantly greater thigh circumference (Psoftball players. The non-elite players were also found to have significantly higher percentage body fat (Psoftball players. The elite female softball players had significantly greater kinanthropometric characteristics, body composition and performance characteristics than the non-elite female softball players.

  1. Performance characteristics of axisymmetric venturi-like reverse-flow diverters. Consolidated Fuel Reprocessing Program

    International Nuclear Information System (INIS)

    Smith, G.V.; Counce, R.M.

    1984-01-01

    This paper presents experimental and model-predicted pressure-flow characteristics of axisymmetric venturi-like reverse-flow diverters (RFDs), the key component of fluid pumping systems utilized for the transport of hazardous fluids. The effects of several key geometric parameters, operating conditions, and fluid properties on the performance of the RFD are presented and compared to model predictions. The results indicate good agreement between data and theory over a large portion of the range of variables studied. Cavitation is observed to be the primary factor in limiting the performance of the RFD at small values of load impedances

  2. Tehachapi Wind Energy Storage Project - Technology Performance Report #3

    Energy Technology Data Exchange (ETDEWEB)

    Pinsky, Naum [Southern California Edison, Rosemead, CA (United States); O' Neill, Lori [Southern California Edison, Rosemead, CA (United States)

    2017-03-31

    The TSP is located at SCE’s Monolith Substation in Tehachapi, California. The 8 MW, 4 hours (32 MWh) BESS is housed in a 6,300 square foot facility and 2 x 4 MW/4.5 MVA smart inverters are on a concrete pad adjacent to the BESS facility. The project will evaluate the capabilities of the BESS to improve grid performance and assist in the integration of large-scale intermittent generation, e.g., wind. Project performance was measured by 13 specific operational uses: providing voltage support and grid stabilization, decreasing transmission losses, diminishing congestion, increasing system reliability, deferring transmission investment, optimizing renewable-related transmission, providing system capacity and resources adequacy, integrating renewable energy (smoothing), shifting wind generation output, frequency regulation, spin/non-spin replacement reserves, ramp management, and energy price arbitrage. Most of the operations either shift other generation resources to meet peak load and other electricity system needs with stored electricity, or resolve grid stability and capacity concerns that result from the interconnection of intermittent generation. SCE also demonstrated the ability of lithium ion battery storage to provide nearly instantaneous maximum capacity for supply-side ramp rate control to minimize the need for fossil fuel-powered back-up generation. The project began in October, 2010 and will continue through December, 2016.

  3. Effects of dimethyl ether on the performance characteristics of a direct methanol fuel cell

    International Nuclear Information System (INIS)

    Seo, Sang Hern; Lee, Chang Sik

    2013-01-01

    Highlights: • Activation loss is significantly reduced in fuel cell with DME-methanol. • DME crossover through the membrane reduces. • The open circuit voltage of DME-methanol the fuel cell increases. • The overall efficiency of the mixed fuel cell is higher than that of DMFC. - Abstract: The objective of this study was to determine the effects of dimethyl ether (DME) on the performance characteristics of a direct methanol fuel cell. Impedance and crossover experiments were performed in order to investigate the performance losses such as ohmic loss, activation loss and crossover loss accurately. The DME was pressurized to 5 bar to supply with liquid phase was and blended with an aqueous methanol solution. In this experiment, the membrane electrode assembly (MEA) was composed of Nafion 115, anode catalyst loaded Pt–Ru and cathode catalyst loaded Pt-Black. Experimental results showed that fuel cells with DME-methanol enhanced performance when compared to fuel cells with methanol only. Such performance enhancement was due to a decrease in activation losses by DME oxidation reactions. As the DME crossover through the membrane was reduced, the open circuit voltage (OCV) of the fuel cell increased. Other output characteristics are also discussed

  4. PERFORMANCE AND CHARACTERISTICS OF MUTUAL FUNDS: EVIDENCE FROM THE PORTUGUESE MARKET

    Directory of Open Access Journals (Sweden)

    Júlio Lobão

    2015-12-01

    Full Text Available In this paper we aim to study the relation between fund performance and fund attributes in the Portuguese market. The sample includes 124 equity funds, bond funds and money market funds that traded in the 2004-2011 period. A comprehensive set of fund-specific characteristics, never used before in conjunction in the literature, was considered. The methodology which was adopted had two distinct phases. Firstly, we compared the returns of each category of funds with the appropriate reference markets. Secondly, the fund performance, measured by the Jensen’s alpha, was used in a multi-factor model with panel data in which the independent variables were the fund attributes. The results show that Portuguese funds were, in general, not able to beat the benchmarks which is consistent with the existence of efficient financial markets. Only the fixed income mutual funds performed well. Moreover, it is possible to conclude that, for each category of mutual funds, their characteristics are useful to the investor in the moment of choosing the best funds. For example, in the case of funds that invest in Portuguese stocks, the best performance occurs among older and larger funds, funds with higher costs, funds with good past performance and funds whose trading activity is low.

  5. Experimental study for flow characteristics and performance evaluation of butterfly valves

    International Nuclear Information System (INIS)

    Kim, C K; Shin, M S; Yoon, J Y

    2010-01-01

    The industrial butterfly valves have been applied to transport a large of fluid with various fields of industry. Also, these are mainly used a control of fluid flux to the water and waste-water pipeline. Present, butterfly valves are manufacturing for multiplicity shape of bodies and discs with many producers. However, appropriate performance evaluation was not yet accomplished to compare about these valves through experiments. This study is performed the experiment of flow characteristics and performance of manufactured 400A butterfly valves for the water and waste pipeline, and compared experimental results. We performed experiments that were controlled fixed a differential pressure condition (1 psi) and the range of the flow rate conditions (500 m 3 /hr ∼ 2500 m 3 /hr), and also opened the disc of valves to a range of angle from 9 degree to 90 degree. We investigated and compared the valve flow coefficient and the valve loss coefficient of results through experiments with each butterfly valve.

  6. Characteristics of Wet Distillers Grains on Ruminal Fermentation and Its Effects on Performance and Carcass Characteristics of Finishing Hanwoo Steers

    Directory of Open Access Journals (Sweden)

    Gyu Chul Ahn

    2016-04-01

    Full Text Available Two experiments were conducted to determine the nutrient composition, in vitro ruminal ammonia concentrations and pH of wet distillers grains (WDG, produced from tapioca 70% and rice 30% and to evaluate dietary effects of fermented total mixed ration (TMR using WDG on the performance, blood metabolites and carcass characteristics of Hanwoo steers from mid fattening to slaughter. In Exp. I, average dry matter (DM, crude protein, ether extract, crude fiber, ash, neutral detergent fiber, acid detergent fiber, and nitrogen free extract of seven WDG samples from an ethanol plant with different sampling dates were 19.9%, 24.8%, 3.8%, 21.8%, 8.87%, 60.3%, 34.5%, and 40.7% (DM basis, respectively. For in vitro ammonia concentrations and pH, each sample was assigned to 7 incubation times (0, 4, 8, 12, 24, 48, and 72 h. Linear increase was observed between 12 and 48 h for ammonia concentrations, but final ammonia concentrations (72 h were not significantly different among WDG samples and fermentation patterns of WDG samples showed similar tendency. In vitro pH varied among treatments from 0 to 24 h, but were not different statistically after 48 h. In Exp. II, 45 Hanwoo steers of 23 months (641±123 kg from mid fattening period to slaughter (248 days were randomly divided into three groups of 15 pens each (five repetitions/each treatment and assigned to one of three dietary treatments; i Control (TMR, ii WDG 15 (TMR containing 15% of WDG, as fed basis and iii WDG 28 (TMR containing 28% of WDG, as fed basis. The body weight (BW, ADG, and feed conversion ratio (FCR of control and WDG 15 and 28 during 248 days were 760.8, 740.1, and 765.5 kg, and 0.50, 0.50, and 0.52 kg/d, and 18.6, 17.6, and 17.1, respectively. The dry matter intake (DMI (kg/d of control (9.11 was higher (p<0.05 than WDG treatments (WDG 15%, 8.57; 28%, 8.70. Nevertheless, DMI did not affect BW, ADG, and FCR of Hanwoo finishing steers. Blood metabolites were in normal ranges and were not

  7. Research on Elemental Technology of Advanced Nuclear Fuel Performance Verification

    International Nuclear Information System (INIS)

    Kim, Yong Soo; Lee, Dong Uk; Jean, Sang Hwan; Koo, Min

    2003-04-01

    Most of current properties models and fuel performance models used in the performance evaluation codes are based on the in-pile data up to 33,000 MWd/MtU. Therefore, international experts are investigating the properties changes and developing advanced prediction models for high burn-up application. Current research is to develop high burn-up fission gas release model for the code and to support the code development activities by collecting data and models, reviewing/assessing the data and models together, and benchmarking the selected models against the appropriate in-pile data. For high burn-up applications, two stage two step fission gas release model is developed based on the real two diffusion process in the grain lattice and grain boundaries of the fission gases and the observation of accelerated release rate in the high burn-up. It is found that the prediction of this model is in excellent agreement with the in-pile measurement results, not only in the low burn-up but also in the high burn-up. This research is found that the importance of thermal conductivity of oxide fuel, especially in the high burn-up, is focused again. It is found that even the temperature dependent models differ from one to another and most of them overestimate the conductivity in the high burn-up. An in-pile data benchmarking of high LHGR fuel rod shows that the difference can reach 30%∼40%, which predicts 400 .deg. C lower than the real fuel centerline temperature. Recent models on the thermal expansion and heat capacity of oxide fuel are found to be well-defined. Irradiation swelling of the oxide fuel are now well-understood that in most cases in LWRs solid fission product swelling is dominant. Thus, the accumulation of in-pile data can enhance the accuracy of the model prediction, rather than theoretical modeling works. Thermo-physical properties of Zircaloy cladding are also well-defined and well-understood except the thermal expansion. However, it turns out that even the

  8. Technology integration performance assessment using lean principles in health care.

    Science.gov (United States)

    Rico, Florentino; Yalcin, Ali; Eikman, Edward A

    2015-01-01

    This study assesses the impact of an automated infusion system (AIS) integration at a positron emission tomography (PET) center based on "lean thinking" principles. The authors propose a systematic measurement system that evaluates improvement in terms of the "8 wastes." This adaptation to the health care context consisted of performance measurement before and after integration of AIS in terms of time, utilization of resources, amount of materials wasted/saved, system variability, distances traveled, and worker strain. The authors' observations indicate that AIS stands to be very effective in a busy PET department, such as the one in Moffitt Cancer Center, owing to its accuracy, pace, and reliability, especially after the necessary adjustments are made to reduce or eliminate the source of errors. This integration must be accompanied by a process reengineering exercise to realize the full potential of AIS in reducing waste and improving patient care and worker satisfaction. © The Author(s) 2014.

  9. High Performance Low Cost Digitally Controlled Power Conversion Technology

    DEFF Research Database (Denmark)

    Jakobsen, Lars Tønnes

    2008-01-01

    in order to reduce the power consumption of servers and datacenters. The work presented in this thesis includes digital control methods for switch-mode converters implemented in microcontrollers, digital signal controllers and field programmable gate arrays. Microcontrollers are cheap devices that can...... be used for real-time control of switch-mode converters. Software design in the assembly language of the microcontroller is important because of the limited resources of the microcontroller. Microcontrollers are best suited for power electronics applications with low bandwidth requirements because...... the execution time of the software algorithm that realises the digital control law will constitute a considerable delay in the control loop. Digital signal controllers are powerful devices capable of performing arithmetic functions much faster than a microcontroller can. Digital signal controllers are well...

  10. PROXIMATE COMPOSITION AND TECHNOLOGICAL CHARACTERISTICS OF DRY PASTA INCORPORATED WITH MICRONIZED CORN PERICARP

    Directory of Open Access Journals (Sweden)

    JOÃO RENATO DE JESUS JUNQUEIRA

    2017-01-01

    Full Text Available Pastas are generally accepted all over the world, mainly because they are versatile, cheap and easy - to - prepare. They are not nutritionally balanced, since they provide mainly carbohydrates. As a result of this, it is important to use ingredients which could improve the nutritional deficiencies, without affecting the technological and sensorial characteristics. This study evaluated the effect of using wheat semolina and micronized corn pericarp (MCP, on the proximate composition, cooking quality and color of spaghetti type pasta. Spaghetti pasta was produced using wheat semolina with the incorporation of micronized corn pericarp, at levels of 0, 10, 20 and 30%. There were no significant differences (p > 0.05 between the formulated samples with regards to the contents of moisture and lipid, cooking time, weight gain and volume increase. As observed, supplementation with micronized corn pericarp presented significant difference on the contents of proteins, minerals, dietary fiber and solid soluble loss of the spaghetti pasta (p < 0.05. With increase in micronized corn pericarp concentration, the color difference became accentuated. The use of MCP appears to be viable, providing a nutritionally enriched product without further impairment on pasta quality.

  11. Uncertainties in HTGR neutron-physical characteristics due to computational errors and technological tolerances

    International Nuclear Information System (INIS)

    Glushkov, E.S.; Grebennik, V.N.; Davidenko, V.G.; Kosovskij, V.G.; Smirnov, O.N.; Tsibul'skij, V.F.

    1991-01-01

    The paper is dedicated to the consideration of uncertainties is neutron-physical characteristics (NPC) of high-temperature gas-cooled reactors (HTGR) with a core as spherical fuel element bed, which are caused by calculations from HTGR parameters mean values affecting NPC. Among NPC are: effective multiplication factor, burnup depth, reactivity effect, control element worth, distribution of neutrons and heat release over a reactor core, etc. The short description of calculated methods and codes used for HTGR calculations in the USSR is given and evaluations of NPC uncertainties of the methodical character are presented. Besides, the analysis of the effect technological deviations in parameters of reactor main elements such as uranium amount in the spherical fuel element, number of neutron-absorbing impurities in the reactor core and reflector, etc, upon the NPC is carried out. Results of some experimental studies of NPC of critical assemblies with graphite moderator are given as applied to HTGR. The comparison of calculations results and experiments on critical assemblies has made it possible to evaluate uncertainties of calculated description of HTGR NPC. (author). 8 refs, 8 figs, 6 tabs

  12. Physical performance characteristics of high-level female soccer players 12-21 years of age.

    Science.gov (United States)

    Vescovi, J D; Rupf, R; Brown, T D; Marques, M C

    2011-10-01

    Performance assessment has become an invaluable component of monitoring player development and within talent identification programs in soccer, yet limited performance data are available for female soccer players across a wide age range. The aim of this study was to describe the physical performance characteristics of female soccer players ranging in age from 12 to 21 years. High-level female soccer players (n=414) were evaluated on linear sprinting (36.6 m with 9.1 m splits), countermovement jump (CMJ), and two agility tests. Separate one-way ANOVAs were used to compare performance characteristics between (1) each year of chronological age and (2) three age groups: 12-13 years, n=78, 14-17 years, n=223, and 18-21 years, n=113. Mean linear sprint speed over 9.1 m was similar across all chronological ages, however sprint speed over the final 9.1 m, CMJ height and agility scores improved until approximately 15-16 years. Outcomes from the group data indicated better performance on all tests for the 14-17-year-old group compared with the 12-13-year-old group. Additionally, sprint speed on the second and fourth 9.1 m splits and 36.6 m sprint speed as well as performance on the Illinois agility test was better in the 18-21-year-old group compared with the 14-17-year-old group. The findings from this study indicate that marked improvements of high intensity short duration work occur up until 15-16 years. Smaller gains in performance were observed beyond 16 years of age as evidenced by better performance on 36.6 m sprint speed, several sprint splits and the Illinois agility test in the college aged players (i.e., 18-21-year-old group). © 2010 John Wiley & Sons A/S.

  13. Specific smartphone usage and cognitive performance affect gait characteristics during free-living and treadmill walking.

    Science.gov (United States)

    Niederer, Daniel; Bumann, Anke; Mühlhauser, Yvonne; Schmitt, Mareike; Wess, Katja; Engeroff, Tobias; Wilke, Jan; Vogt, Lutz; Banzer, Winfried

    2018-04-06

    Mobile phone tasks like texting, typing, and dialling during walking are known to impact gait characteristics. Beyond that, the effects of performing smartphone-typical actions like researching and taking self-portraits (selfie) on gait have not been investigated yet. We aimed to investigate the effects of smartphone usage on relevant gait characteristics and to reveal potential association of basic cognitive and walking plus smartphone dual-task abilities. Our cross-sectional, cross-over study on physically active, healthy participants was performed on two days, interrupted by a 24-h washout in between. Assessments were: 1) Cognitive testing battery consisting of the trail making test (TMT A and B) and the Stroop test 2) Treadmill walking under five smartphone usage conditions: no use (control condition), reading, dialling, internet searching and taking a selfie in randomized order. Kinematic and kinetic gait characteristics were assessed to estimate conditions influence. In our sample of 36 adults (24.6 ± 1 years, 23 female, 13 male), ANCOVAs followed by post-hoc t-tests revealed that smartphone usage impaired all tested gait characteristics: gait speed (decrease, all conditions): F = 54.7, p smartphone usage was systematically associated with the TMT B time regarding cadence and double stride length for reading (r = -0.37), dialling (r = -0.35) and taking a selfie (r = -0.34). Smartphone usage substantially impacts walking characteristics in most situations. Changes of gait patterns indicate higher cognitive loads and lower awareness. Copyright © 2018 Elsevier B.V. All rights reserved.

  14. Multimedia Superabrasive, Laser Cladding, and Waterjet Technology Performance Support System

    International Nuclear Information System (INIS)

    Bohley, M.C.; Ciccateri, T.J.

    1998-01-01

    The objective of this project was to create a system that delivered the appropriate information to the machine tool user just when needed and in the most appropriate form. The expertise of FM and T in the areas of instructional system design and multimedia creation was employed. Huffman brought together their subject matter experts from engineering, manufacturing, technical writing, and technical support. AlliedSignal FM and T worked together with Huffman as a design team to determine what tasks must be accomplished throughout the machine tool production phases, who performs those tasks, what skills are utilized, and what information is required to support the tasks. This project resulted in the identification of information flow throughout the life cycle of the machine tool products. Specialized tools required for assembly and calibration procedures were identified and their images captured, digitized, and stored for easy retrieval within the PSS. Subject matter experts were interviewed to determine which tasks require highly specialized knowledge and skills. These tasks were then performed on actual machines and the technicians' actions captured on video tape. The resulting video segments were edited, digitized, and integrated into the information system portion of the PSS where they are available for viewing alongside procedural information presented on the computer display screen of the machine tool controller. Information from Troubleshooting experts were interviewed regarding the symptoms and root causes of system malfunctions. This knowledge was captured and fault trees were developed. These trees were then incorporated into an expert system as a rule base. The troubleshooting portion of the PSS presents simple questions to the machine operator in order to determine the likely cause of malfunctions and then recommended corrective actions. Newly created and existing reference information was both created and re-purposed from other existing formats, then

  15. Performance and carcass characteristics of lambs fed on diets supplemented with glycerin from biodiesel production

    Directory of Open Access Journals (Sweden)

    Marco Antonio Bensimon Gomes

    2011-10-01

    Full Text Available This study was carried out to evaluate the influence of diets supplemented with glycerin as an alternative ingredient to corn on the performance and carcass characteristics of Santa Inês confined lambs. The study involved 27 lambs aged 90 days, having an average initial weight of 26.33 ± 0.15 kg. Lambs were randomly distributed into a control group and groups with diets containing 15 and 30% glycerin in the total feed. Diet was formulated with 40% roughage and 60% concentrate. The experimental design was completely randomized, and the production performance and carcass characteristics were analyzed by analysis of variance, and the subjective carcass characteristics, by general linear models. The daily average gain was 0.21, 0.24 and 0.23 kg/day; feeding conversion was 6.39, 5.73 and 5.92 kg of diet/kg BW for control animals, and those fed with 15 or 30% glycerin, respectively, without treatment differences. Lambs were slaughtered, weighing 34 to 36 kg, and average weight of the cold carcass and commercial carcass yield were evaluated. The results were, respectively, 15.97 kg and 49.18%, for control, 15.96 kg and 48.31% for animals fed with 15% glycerin, and 15.79 kg and 47.87% for those treated with 30% glycerin, with no treatment effects. Meat tenderness and cooking loss averages were not affected by diets, with 5.07 kg and 40.45%, 5.10 kg and 40.81%, and 5.27 kg and 39.04%, respectively, for control, and those fed with 15 or 30% glycerin. Therefore, it is possible to conclude that up to 30% of medium purity glycerin in the dry matter of the diet can be used to replace corn, without any negative effect on lamb performance or carcass characteristics.

  16. Performance of digital integrated circuit technologies at very high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Prince, J.L.; Draper, B.L.; Rapp, E.A.; Kromberg, J.N.; Fitch, L.T.

    1980-01-01

    Results of investigations of the performance and reliability of digital bipolar and CMOS integrated circuits over the 25 to 340/sup 0/C range are reported. Included in these results are both parametric variation information and analysis of the functional failure mechanisms. Although most of the work was done using commercially available circuits (TTL and CMOS) and test chips from commercially compatible processes, some results of experimental simulations of dielectrically isolated CMOS are also discussed. It was found that commercial Schottky clamped TTL, and dielectrically isolated, low power Schottky-clamped TTL, functioned to junction temperatures in excess of 325/sup 0/C. Standard gold doped TTL functioned only to 250/sup 0/C, while commercial, isolated I/sup 2/L functioned to the range 250/sup 0/C to 275/sup 0/C. Commercial junction isolated CMOS, buffered and unbuffered, functioned to the range 280/sup 0/C to 310/sup 0/C/sup +/, depending on the manufacturer. Experimental simulations of simple dielectrically isolated CMOS integrated circuits, fabricated with heavier doping levels than normal, functioned to temperatures in excess of 340/sup 0/C. High temperature life testing of experimental, silicone-encapsulated simple TTL and CMOS integrated circuits have shown no obvious life limiting problems to date. No barrier to reliable functionality of TTL bipolar or CMOS integrated ciruits at temperatures in excess of 300/sup 0/C has been found.

  17. Putting market-facing technology to work: Organizational drivers of CRM performance

    NARCIS (Netherlands)

    Saini, A.; Grewall, R.; Johnson, J.L.

    2010-01-01

    A large proportion of firms that adopt customer relationship management (CRM) technology find it challenging to integrate CRM technology into their core marketing processes and utilize CRM strategically to appreciably improve their performance. The authors conceptualize a model to understand the

  18. Construction Project Performance Improvement through Radio Frequency Identification Technology Application on a Project Supply Chain

    Science.gov (United States)

    Wang, Heng

    2017-01-01

    Construction project productivity typically lags other industries and it has been the focus of numerous studies in order to improve the project performance. This research investigated the application of Radio Frequency Identification (RFID) technology on construction projects' supply chain and determined that RFID technology can improve the…

  19. Characteristics of shift work and their impact on employee performance and wellbeing: A literature review.

    Science.gov (United States)

    Dall'Ora, Chiara; Ball, Jane; Recio-Saucedo, Alejandra; Griffiths, Peter

    2016-05-01

    To identify the characteristics of shift work that have an effect on employee's performance (including job performance, productivity, safety, quality of care delivered, errors, adverse events and client satisfaction) and wellbeing (including burnout, job satisfaction, absenteeism, intention to leave the job) in all sectors including healthcare. A scoping review of the literature was undertaken. We searched electronic databases (CINAHL, MEDLINE, PsychINFO, SCOPUS) to identify primary quantitative studies. The search was conducted between January and March 2015. Studies were drawn from all occupational sectors (i.e. health and non health), meeting the inclusion criteria: involved participants aged ≥18 who have been working shifts or serve as control group for others working shifts, exploring the association of characteristics of shift work with at least one of the selected outcomes. Reference lists from retrieved studies were checked to identify any further studies. 35 studies were included in the review; 25 studies were performed in the health sector. A variety of shift work characteristics are associated with compromised employee's performance and wellbeing. Findings from large multicentre studies highlight that shifts of 12h or longer are associated with jeopardised outcomes. Working more than 40h per week is associated with adverse events, while no conclusive evidence was found regarding working a 'Compressed Working Week'; working overtime was associated with decreased job performance. Working rotating shifts was associated with worse job performance outcomes, whilst fixed night shifts appeared to enable resynchronisation. However, job satisfaction of employees working fixed nights was reduced. Timely breaks had a positive impact on employee fatigue and alertness, whilst quick returns between shifts appeared to increase pathologic fatigue. The effect of shift work characteristics on outcomes in the studies reviewed is consistent across occupational sectors

  20. Firm Characteristics and Performance Disclosure in Annual Reports of Nigerian Banks using the Balanced Scorecard

    Directory of Open Access Journals (Sweden)

    Solabomi Ajibolade

    2017-05-01

    Full Text Available This study investigated the influence of four firm characteristics (size, organisational structure, age and systemic importance on extent of performance disclosures by Nigerian banks using the balanced scorecard (BSC model. The population of the study comprised of publicly-listed banks in Nigeria, in operation from 2012 to 2014. Using a self-designed disclosure checklist, the annual reports of a sample of 15 publicly quoted banks in Nigeria were content-analysed for performance disclosure for the period 2012-2014. Descriptive statistics, t-test and Analysis of Variance (ANOVA were applied in data analysis, deducing inference at 5% significance level. It was observed that firms did not significantly differ in the extent of performance disclosure in each of the four BSC perspectives on one hand, and the overall BSC measure on the other hand, on the account of the four firm attributes examined. Considering that annual reports are mainstream amongst the media used to communicate firm performance to the public, it was recommended that preparers of such documents should consider disclosing financial and non-financial performance; this will not only provide a comprehensive basis to judge organisational performance, but will also assist in diffusing the clout created by asymmetry of information between preparers and users of performance reports.

  1. Teacher characteristics and student performance: An analysis using hierarchical linear modelling

    Directory of Open Access Journals (Sweden)

    Paula Armstrong

    2015-12-01

    Full Text Available This research makes use of hierarchical linear modelling to investigate which teacher characteristics are significantly associated with student performance. Using data from the SACMEQ III study of 2007, an interesting and potentially important finding is that younger teachers are better able to improve the mean mathematics performance of their students. Furthermore, younger teachers themselves perform better on subject tests than do their older counterparts. Identical models are run for Sub Saharan countries bordering on South Africa, as well for Kenya and the strong relationship between teacher age and student performance is not observed. Similarly, the model is run for South Africa using data from SACMEQ II (conducted in 2002 and the relationship between teacher age and student performance is also not observed. It must be noted that South African teachers were not tested in SACMEQ II so it was not possible to observe differences in subject knowledge amongst teachers in different cohorts and it was not possible to control for teachers’ level of subject knowledge when observing the relationship between teacher age and student performance. Changes in teacher education in the late 1990s and early 2000s may explain the differences in the performance of younger teachers relative to their older counterparts observed in the later dataset.

  2. Overview of the Performance and Cost Effectiveness of Small Arsenic Removal Technologies

    Science.gov (United States)

    Presentation provides information on the performance and cost of primarily four arsenic removal technologies; adsorptive media, iron removal, coagulation/filtration and the combination system of iron removal followed by adsorptive media.

  3. FY 1997 Blue Book: High Performance Computing and Communications: Advancing the Frontiers of Information Technology

    Data.gov (United States)

    Networking and Information Technology Research and Development, Executive Office of the President — The Federal High Performance Computing and Communications HPCC Program will celebrate its fifth anniversary in October 1996 with an impressive array of...

  4. IMPROVING THE ENVIRONMENTAL PERFORMANCE OF CHEMICAL PROCESSES THROUGH THE USE OF INFORMATION TECHNOLOGY

    Science.gov (United States)

    Efforts are currently underway at the USEPA to develop information technology applications to improve the environmental performance of the chemical process industry. These efforts include the use of genetic algorithms to optimize different process options for minimal environmenta...

  5. Perceptions of technology uncertainty and the consequences for performance in buyer-supplier relationships

    NARCIS (Netherlands)

    Oosterhuis, M.; van der Vaart, T.; Molleman, E.

    2011-01-01

    In this paper, we investigate how buyers' and suppliers' distinct perceptions of technology uncertainty affect the relationship between communication frequency and supplier performance. Information processing theory suggests that a fit is desirable between perceived environmental uncertainty and the

  6. An Analysis of Information Technology Training Effectiveness: The Impact on Trainee Reactions, Learning, and Performance

    National Research Council Canada - National Science Library

    Scherrer, Joseph

    1998-01-01

    .... "Information Dominance" has assumed a central role in such environments. In order to achieve Information Dominance, the Air Force must have trained and skilled personnel able to perform highly intensive activities using information technologies...

  7. Work-group characteristics and performance in collectivistic and individualistic cultures.

    Science.gov (United States)

    Sosik, John J; Jung, Dong I

    2002-02-01

    The authors conducted a cross-cultural longitudinal investigation of the effects of culture (individualism-collectivism dichotomy) on group characteristics (functional heterogeneity, preference for teamwork, group potency, outcome expectation) and on performance of 83 work groups performing 2 decision-making tasks over a 15-week period. The individualists (U.S. students) reported higher levels of functional heterogeneity and group potency and attained higher levels of group performance than did the collectivists (Korean students). In addition, culture and time interacted to influence ratings of group potency and outcome expectation. The difference in ratings of group potency between individualists and collectivists increased over time. Outcome expectation was greater among the collectivists in Time 1 and among the individualists in Time 2. The authors discuss implications for future cross-cultural group research and international management.

  8. Determination of performance characteristics of robotic manipulator's permanent magnet synchronous motor by learning its FEM model

    International Nuclear Information System (INIS)

    Bharadvaj, Bimmi; Saini, Surendra Singh; Swaroop, Teja Tumapala; Sarkar, Ushnish; Ray, Debashish Datta

    2016-01-01

    Permanent Magnet Synchronous Motors (PMSM) are widely used as actuators because of high torque density, high efficiency and reliability. Robotic Manipulator designed for specific task generally requires actuators with very high intermittent torque and speed for their operation in limited space. Hence accurate performance characteristics of PMSM must be known beforehand under these conditions as it may damage the motor. Therefore an advanced mathematical model of PMSM is required for its control synthesis and performance analysis over wide operating range. The existing mathematical models are developed considering ideal motor without including the geometrical deviations that occur during manufacturing process of the motor or its components. These manufacturing tolerance affect torque ripple, operating current range etc. thereby affecting motor performance. In this work, the magnetically non-linear dynamic model is further exploited to refine the FE model using a proposed algorithm to iteratively compensate for the experimentally observed deviations due to manufacturing. (author)

  9. BOARD OF DIRECTORS, AUDIT COMMITTEE CHARACTERISTICS AND THE PERFORMANCE OF SAUDI ARABIA LISTED COMPANIES

    Directory of Open Access Journals (Sweden)

    Yahya Ali Al-Matari

    2012-01-01

    Full Text Available This study examines the relationship between the internal corporate governance mechanism related to the board of directors, the audit committee characteristics and the performance of the Saudi companies listed in the Saudi stock exchange (TADAWL in 2010, excluding financial companies. The statistical results of the study are not in line with the agency theory that board of directors and audit committee might mitigate agency problems leading to reduced agency cost by aligning the interests of controlling owners with those of the company. While audit Committee size (ACSIZE is found to have a significant relationship with firm performance (but in the opposite direction to expectation, other hypothesized variables, the proportion of non-executive directors (BODCOM, CEO Duality (DUAL, Board Size (BSIZE, Audit Committee Independence (ACIND, audit committee meeting (ACMEET were found to be as expected directions but insignificantly related to firm performance measure except the direction of the proportion of non-executive directors (BODCOM was opposite to the expectations.

  10. Effect of Fuel Injection and Mixing Characteristics on Pulse-Combustor Performance at High-Pressure

    Science.gov (United States)

    Yungster, Shaye; Paxson, Daniel E.; Perkins, Hugh D.

    2014-01-01

    Recent calculations of pulse-combustors operating at high-pressure conditions produced pressure gains significantly lower than those observed experimentally and computationally at atmospheric conditions. The factors limiting the pressure-gain at high-pressure conditions are identified, and the effects of fuel injection and air mixing characteristics on performance are investigated. New pulse-combustor configurations were developed, and the results show that by suitable changes to the combustor geometry, fuel injection scheme and valve dynamics the performance of the pulse-combustor operating at high-pressure conditions can be increased to levels comparable to those observed at atmospheric conditions. In addition, the new configurations can significantly reduce the levels of NOx emissions. One particular configuration resulted in extremely low levels of NO, producing an emission index much less than one, although at a lower pressure-gain. Calculations at representative cruise conditions demonstrated that pulse-combustors can achieve a high level of performance at such conditions.

  11. Performance and internal flow characteristics of a cross-flow turbine by guide vane angle

    International Nuclear Information System (INIS)

    Chen, Z M; Choi, Y D

    2013-01-01

    This study attempts to investigate the performance and internal flow characteristics of a cross-flow turbine by guide vane angle. In order to improve the performance of a cross flow turbine, the paper presents a numerical investigation of the turbine with air supply and discusses the influence of variable guide vane angle on the internal flow. A newly developed air supply from air suction Hole is adopted. To investigate the performance and internal flow of the cross-flow turbine, the CFD software based on the two-phase flow model is utilized. The numerical grids are made in two-dimensional geometry in order to shorten the time of two-phase calculations. Then a series of CFD analysis has been conducted in the range of different guide vane angle. Moreover, local output power is divided at different stages and the effect of air layer in each stage is examined

  12. Designing the organizational creativity based on job characteristics and job involvement among physical education units’ employees of Technology University

    Directory of Open Access Journals (Sweden)

    Seyed Hossein Alavi

    2017-10-01

    Full Text Available The aim of the present study was designing the organizational creativity based on job characteristics and job involvement among physical education employees of Technology University. The statistical population of the present study consisted of all employees, experts, and physical education units’ managers. The statistical samples were 389 people reduced to 338 employees after eliminating the incomplete and useless questionnaires. The research method of the present study was descriptive-correlative. Three questionnaires of job characteristics, job involvement, and organizational creativity were used to evaluate the research variables which were distributed and gathered among research samples after translation and comparison with research samples via face validity (views of 12 sport management experts and construct validity. The research results were analyzed by Partial Least Square (PLS and showed that the best predictor of job involvement among physical education units’ employees of Technology University was problem solving (ES= 0.41. However, the job characteristics of autonomy (0.26 and job feedback (.024 had more effects on employees’ creativity. Other results showed that managers reported lower scores of job characteristics and creativity than sport employees. According to research findings, in order to achieve creativity in the workplace within physical education units of Technology University, the managers should stimulate the autonomy and feedback characteristics. Of course, it should not be neglected that this mechanism would be facilitated by creating the problem solving in job.

  13. Measuring process performance within healthcare logistics - a decision tool for selecting measuring technologies

    DEFF Research Database (Denmark)

    Feibert, Diana Cordes; Jacobsen, Peter

    2015-01-01

    Performance measurement can support the organization in improving the efficiency and effectiveness of logistical healthcare processes. Selecting the most suitable technologies is important to ensure data validity. A case study of the hospital cleaning process at a public Danish hospital...... was conducted. Monitoring tasks and ascertaining quality of work is difficult in such a process. Based on principal-agent theory, a set of decision indicator has been developed, and a decision framework for assessing technologies to enable performance measurement has been proposed....

  14. Effects of Technological Innovation in Relationship between Green Supply Chain Management Practices and Green Performance

    OpenAIRE

    Umar, Mohammed Sangiru; Danjuma, Ibrahim; Hammawa, Dahiru Dauda; Habibu, Sherif Ahmed

    2016-01-01

    Although scholars have conceptualised on green supply chain management practices and green performance, evidence to validate the conceptualisation was lacking, albeit in the context of small and medium enterprises. In addition, effect of technological innovation on supply chain practices and green performance was largely unexplored by researchers. Therefore this study validates and provides empirical evidence on the relationship between green supply chain management practices, technological i...

  15. Performance planning and measurement for DOE EM-International Technology Integration Program. A report on a performance measurement development workshop for DOE's environmental management international technology integration program

    International Nuclear Information System (INIS)

    Jordan, G.B.; Reed, J.H.; Wyler, L.D.

    1997-03-01

    This report describes the process and results from an effort to develop metrics for program accomplishments for the FY 1997 budget submission of the U.S. Department of Energy Environmental Management International Technology Integration Program (EM-ITI). The four-step process included interviews with key EM-ITI staff, the development of a strawman program logic chart, and all day facilitated workshop with EM-ITI staff during which preliminary performance plans and measures were developed and refined, and a series of follow-on discussions and activities including a cross-organizational project data base. The effort helped EM-ITI to crystallize and develop a unified vision of their future which they can effectively communicate to their own management and their internal and external customers. The effort sets the stage for responding to the Government Performance and Results Act. The metrics developed may be applicable to other international technology integration programs. Metrics were chosen in areas of eight general performance goals for 1997-1998: (1) number of forums provided for the exchange of information, (2) formal agreements signed, (3) new partners identified, (4) customers reached and satisfied, (5, 6) dollars leveraged by EM technology focus area and from foreign research, (7) number of foreign technologies identified for potential use in remediation of DOE sites, and (8) projects advanced through the pipeline

  16. The gender gap reloaded: are school characteristics linked to labor market performance?

    Science.gov (United States)

    Konstantopoulos, Spyros; Constant, Amelie

    2008-06-01

    This study examines the wage gender gap of young adults in the 1970s, 1980s, and 2000 in the US. Using quantile regression we estimate the gender gap across the entire wage distribution. We also study the importance of high school characteristics in predicting future labor market performance. We conduct analyses for three major racial/ethnic groups in the US: Whites, Blacks, and Hispanics, employing data from two rich longitudinal studies: NLS and NELS. Our results indicate that while some school characteristics are positive and significant predictors of future wages for Whites, they are less so for the two minority groups. We find significant wage gender disparities favoring men across all three surveys in the 1970s, 1980s, and 2000. The wage gender gap is more pronounced in higher paid jobs (90th quantile) for all groups, indicating the presence of a persistent and alarming "glass ceiling."

  17. Design and performance characteristic analysis of servo valve-type water hydraulic poppet valve

    International Nuclear Information System (INIS)

    Park, Sung Hwan

    2009-01-01

    For water hydraulic system control, the flow or pressure control using high-speed solenoid valve controlled by PWM control method could be a good solution for prevention of internal leakage. However, since the PWM control of on-off valves cause extensive flow and pressure fluctuation, it is difficult to control the water hydraulic actuators precisely. In this study, the servo valve-type water hydraulic valve using proportional poppet as the main valve is designed and the performance characteristics of the servo valve-type water hydraulic valve are analyzed. Furthermore, it is demonstrated through experiments that a decline in control chamber pressure that follows the change of pilot flow is caused by the occurrence of cavitation around the proportional poppet, and that fundamental characteristics of the developed valve remain unaffected by the occurrence of cavitation

  18. Generic anthropometric and performance characteristics among elite adolescent boys in nine different sports.

    Science.gov (United States)

    Pion, Johan; Segers, Veerle; Fransen, Job; Debuyck, Gijs; Deprez, Dieter; Haerens, Leen; Vaeyens, Roel; Philippaerts, Renaat; Lenoir, Matthieu

    2015-01-01

    The aim of the present study was to evaluate the Flemish Sports Compass (FSC), a non-sport-specific generic testing battery. It was hypothesised that a set of 22 tests would have sufficient discriminant power to allocate athletes to their own sport based on a unique combination of test scores. First, discriminant analyses were applied to the 22 tests of anthropometry, physical fitness and motor coordination in 141 boys under age 18 (16.1 ± 0.8 years) and post age at peak height velocity (maturity offset = 2.674 ± 0.926) from Flemish Top Sport Academies for badminton, basketball, gymnastics, handball, judo, soccer, table tennis, triathlon and volleyball. Second, nine sequential discriminant analyses were used to assess the ability of a set of relevant performance characteristics classifying participants and non-participants for the respective sports. Discriminant analyses resulted in a 96.4% correct classification of all participants for the nine different sports. When focusing on relevant performance characteristics, 80.1% to 97.2% of the total test sample was classified correctly within their respective disciplines. The discriminating characteristics were briefly the following: flexibility in gymnastics, explosive lower-limb strength in badminton and volleyball, speed and agility in badminton, judo, soccer and volleyball, upper-body strength in badminton, basketball and gymnastics, cardiorespiratory endurance in triathletes, dribbling skills in handball, basketball and soccer and overhead-throwing skills in badminton and volleyball. The generic talent characteristics of the FSC enable the distinction of adolescent boys according to their particular sport. Implications for talent programmes are discussed.

  19. Intercomparison of performance characteristics of OSLDs and TLDs used for individual monitoring

    International Nuclear Information System (INIS)

    Meye, Phillipe Ondo

    2016-07-01

    This research work performed an intercomparison on some important performance characteristics of optically stimulated luminescence (OSL) and thermoluminescence (TL) dosimetry systems used by dosimetry services in Gabon and Ghana, respectively. The study verified the status of the selected performance indicators and propose ways to improve the performances of individual monitoring services of Ghana and Gabon if found necessary. The performance indicators assessed included the zero - dose, the minimum detectability and some important reader performance characteristics. These tests were performed using statistical and experimental methods. The overall uncertainty in measurement of the dosimetry systems of Ghana and Gabon for Hp(10) was determined using the IEC technical report TR 62461, and comparisons were carried out with IAEA 99, PTB 99, IEC 1066 and IEC1283 series performance standards. The IEC 62387 standard was used to assess the linearity dependence of the response and the coefficient of variation of the two dosimetry systems. For the Harshaw TLD 6600 system of the dosimetry service of Ghana, the Reference light QC test meets the requirement given in the user manual. For the OSL system microStar of the dosimetry system of Gabon, the three QC tests, DRK count, CAL count and LED count, meet the user manual requirements. However all these tests failed the statistical test that is part of counting statistics. This led to the conclusion that there may be some abnormalities in the counting system, and that the statistical abnormalities suspected have apparently no impact on the results of the reading. It was also concluded that since the DRK count and the CAL count failed the Chi - squared test by very small margin, a Gaussian distribution could still be considered as an approximation of the experimental data distributions of these two QC measurements. The zero dose for the Harshaw 6600 and the microStar system were found to be 0.026 mSv and 0.08 mSv respectively

  20. Radical production efficiency and electrical characteristics of a coplanar barrier discharge built by multilayer ceramic technology

    International Nuclear Information System (INIS)

    Jõgi, Indrek; Erme, Kalev; Levoll, Erik; Stamate, Eugen

    2017-01-01

    The present study investigated the electrical characteristics and radical production efficiency of a coplanar barrier discharge (CBD) device manufactured by Kyocera by multilayer ceramic technology. The device consisted of a number of linear electrodes with electrode and gap widths of 0.75 mm, immersed into a ceramic dielectric barrier. A closed flow-through system necessary for the measurements was prepared by placing a quartz plate at a height of 3 mm from the ceramic barrier. The production of nitrogen radicals was determined from the removal of a trace amount of NO in pure N 2 gas, while the production of oxygen radicals was determined by ozone production in pure O 2 or synthetic air. The production efficiency of N and O radicals and NO oxidation in synthetic air was comparable with the efficiency of a volume barrier discharge device. The power density per unit of surface area of the CBD device was more than two times larger than that of a similar volume barrier discharge setup, which makes the CBD device a compact alternative for gas treatment. The production of ozone and different nitrogen oxides was also evaluated for the open system of the CBD which is usable for surface treatment. The ozone concentration of this system was nearly independent from the input power, while the concentration of nitrogen oxides increased with input power. The open system of the CBD was additionally tested for the treatment of a silicon surface. An increase of applied power decreased the time required to reduce the water contact angle below 10 degrees but also started to have an impact on the surface roughness. (paper)