Hitch code capabilities for modeling AVT chemistry

International Nuclear Information System (INIS)

Leibovitz, J.

1985-01-01

Several types of corrosion have damaged alloy 600 tubing in the secondary side of steam generators. The types of corrosion include wastage, denting, intergranular attack, stress corrosion, erosion-corrosion, etc. The environments which cause attack may originate from leaks of cooling water into the condensate, etc. When the contaminated feedwater is pumped into the generator, the impurities may concentrate first 200 to 400 fold in the bulk water, depending on the blowdown, and then further to saturation and dryness in heated tube support plate crevices. Characterization of local solution chemistries is the first step to predict and correct the type of corrosion that can occur. The pH is of particular importance because it is a major factor governing the rate of corrosion reactions. The pH of a solution at high temperature is not the same as the ambient temperature, since ionic dissociation constants, solubility and solubility products, activity coefficients, etc., all change with temperature. Because the high temperature chemistry of such solutions is not readily characterized experimentally, modeling techniques were developed under EPRI sponsorship to calculate the high temperature chemistry of the relevant solutions. In many cases, the effects of cooling water impurities on steam generator water chemistry with all volatile treatment (AVT), upon concentration by boiling, and in particular the resulting acid or base concentration can be calculated by a simple code, the HITCH code, which is very easy to use. The scope and applicability of the HITCH code are summarized

WTEC panel report on research submersibles and undersea technologies

Science.gov (United States)

Seymore, Richard J.; Blidberg, D. Richard; Brancart, Claude P.; Gentry, Larry L.; Kalvaitis, Algis N.; Lee, Michael J.; Mooney, Brad; Walsh, Don

1994-06-01

This report covers research submersibles and related subsea technologies in Finland, France, Russia, Ukraine and the United Kingdom. Manned, teleoperated, and autonomous submersibles were of interest. The panel found that, in contrast to the United States, Europe is making substantial progress in cooperative and coordinated research in subsea technology, including the development of standards. France is a leader in autonomous vehicle technology. Because much less was known a priori about the technologies in Russia and Ukraine, there were more new findings in those countries than in those Western European nations visited. However, Russia and Ukraine have a sizeable (and currently underutilized) infrastructure in this field, including a highly educated and experienced manpower pool, impressive (in some cases unique) facilities for physical testing, extensive fleets of seagoing research vessels capable of long voyages, and state-of-the-art facilities for conducting oceanographic investigations. The panel visited newly-formed commercial companies associated with long-standing submersible R&D and production centers in Russia and Ukraine. So far, these new efforts are undercapitalized, and as such represent opportunities at very low cost for Western nations, as detailed in the site reports.

Consolidation of HIP bonding technologies for the ITER first wall panels

International Nuclear Information System (INIS)

Sherlock, P.; Peacock, A.; Roedig, M.

2006-01-01

Over the last decade alternative technologies for the manufacture of the ITER first wall have been progressively developed. Now, as the build of ITER approaches, the manufacturing route is being consolidated around the best solutions found to date. The design of the first wall is based on the concept of blanket modules, each faced by separable first wall panels. For the manufacture of the first wall panels two HIP bonding technologies are proposed by AMEC NNC; the first to bond together the composite copper alloy / stainless steel heat sink base, the second to bond the beryllium tiles to the copper alloy surface of the heat sink base. These technologies have been developed incrementally through the use of experiments, part scale mock-ups and full scale first wall panel prototypes. This paper reviews the development of the HIP bonding technologies identified above and discusses the latest results from components produced by AMEC NNC under the auspices of EFDA. The manufacturing stages, non-destructive examination and heat flux test results from the work are presented for the latest first wall mock-up components. Conclusions are then drawn with regard to the important aspects for the series production of components for ITER. (author)

Flight Test of a Technology Transparent Light Concentration Panel on SMEX/WIRE

Science.gov (United States)

Stern, Theodore G.; Lyons, John

2000-01-01

A flight experiment has demonstrated a modular solar concentrator that can be used as a direct substitute replacement for planar photovoltaic panels in spacecraft solar arrays. The Light Concentrating Panel (LCP) uses an orthogrid arrangement of composite mirror strips to form an array of rectangular mirror troughs that reflect light onto standard, high-efficiency solar cells at a concentration ratio of approximately 3:1. The panel area, mass, thickness, and pointing tolerance has been shown to be similar to a planar array using the same cells. Concentration reduces the panel's cell area by 2/3, which significantly reduces the cost of the panel. An opportunity for a flight experiment module arose on NASA's Small Explorer / Wide-Field Infrared Explorer (SMEX/WIRE) spacecraft, which uses modular solar panel modules integrated into a solar panel frame structure. The design and analysis that supported implementation of the LCP as a flight experiment module is described. Easy integration into the existing SMEX-LITE wing demonstrated the benefits of technology transparency. Flight data shows the stability of the LCP module after nearly one year in Low Earth Orbit.

76 FR 38648 - Availability of the Geothermal Technologies Program Blue Ribbon Panel Report and Request for...

Science.gov (United States)

2011-07-01

....S. has lagged that of solar and wind energy. The purpose of the Blue Ribbon Panel meeting was to... Geothermal Technologies Program Blue Ribbon Panel Report and Request for Public Comment AGENCY: Office of... Panel (the Panel) on March 22/23, 2011 in Albuquerque, New Mexico for a guided discussion on the future...

Influence of the"Business Tax to AVT"to the Software Enterprise and the Coping Strategies%浅析“营改增”对软件企业的影响及应对策略

Institute of Scientific and Technical Information of China (English)

徐玉

2014-01-01

The Ministry of Finance and State Administration of Taxation require that Shanghai carry out the business tax to AVT from January 1, 2012, which influent software enterprises significantly. From the macro level analysis,"Business tax to AVT"can help to alleviate burdens on software enterprises. From the micro level analysis,"Business tax to AVT"has different effects on different types of software enterprises. In this paper, the analysis of"Business tax to AVT"shows the challenges and the effect it makes to software enterprises. It also tries to explore the coping strategies for software enterprises.%财政部、国家税务总局要求2012年1月1日起，率先在上海市开展营业税改征增值税的试点，此次改革对软件企业影响显著。从宏观层面分析，“营改增”对于软件业整体具有减负的效果。从微观层面分析，“营改增”则对不同类型的软件企业具有不同的影响。为此，本文通过实例，分析“营改增”对软件企业产生的效应及带来的挑战，尝试探究软件企业的应对策略。

Impact of energy technology patents in China: Evidence from a panel cointegration and error correction model

International Nuclear Information System (INIS)

Li, Ke; Lin, Boqiang

2016-01-01

Enhancing energy technology innovation performance, which is widely measured by energy technology patents through energy technology research and development (R&D) activities, is a fundamental way to implement energy conservation and emission abatement. This study analyzes the effects of R&D investment activities, economic growth, and energy price on energy technology patents in 30 provinces of China over the period 1999–2013. Several unit root tests indicate that all the above variables are generated by panel unit root processes, and a panel cointegration model is confirmed among the variables. In order to ensure the consistency of the estimators, the Fully-Modified OLS (FMOLS) method is adopted, and the results indicate that R&D investment activities and economic growth have positive effects on energy technology patents while energy price has a negative effect. However, the panel error correction models indicate that the cointegration relationship helps to promote economic growth, but it reduces R&D investment and energy price in the short term. Therefore, market-oriented measures including financial support and technical transformation policies for the development of low-carbon energy technologies, an effective energy price mechanism, especially the targeted fossil-fuel subsidies and their die away mode are vital in promoting China's energy technology innovation. - Highlights: • Energy technology patents in China are analyzed. • Relationship between energy patents and funds for R&D activities are analyzed. • China's energy price system hinders energy technology innovation. • Some important implications for China's energy technology policy are discussed. • A panel cointegration model with FMOLS estimator is used.

Tracking the New Technology. A Summary of the Second Invitational Postsecondary Educational Review Panel.

Science.gov (United States)

Sterling, C. H.

The second educational technology review panel addressed problems with forecasting the trends and impact of newer telecomunications technologies in both home and institution of higher education settings, and the role of several grant programs in educational technology. Paul Mertins provided an update on a National Center for Education Statistics…

Energy prices, technological knowledge and green energy innovation. A dynamic panel analysis of patent counts

International Nuclear Information System (INIS)

Kruse, Juergen; Wetzel, Heike; Koeln Univ.

2014-01-01

We examine the effect of energy prices and technological knowledge on innovation in green energy technologies. In doing so, we consider both demand-pull effects, which induce innovative activity by increasing the expected value of innovations, and technology-push effects, which drive innovative activity by extending the technological capability of an economy. Our analysis is conducted using patent data from the European Patent Office on a panel of 26 OECD countries over the period 1978-2009. Utilizing a dynamic count data model for panel data, we analyze 11 distinct green energy technologies. Our results indicate that the existing knowledge stock is a significant driver of green energy innovation for all technologies. Furthermore, the results suggest that energy prices have a positive impact on innovation for some but not all technologies and that the e.ect of energy prices and technological knowledge on green energy innovation becomes more pronounced after the Kyoto protocol agreement in 1997.

International Linear Collider Steering Committee issues charge to Technology Recommendation Panel

CERN Multimedia

2003-01-01

"Following its November 19 meeting in Paris, the International Linear Collider Steering Committee, a subcommittee of the International Committee for Future Accelerators, has published the charge http://www.fnal.gov/directorate/icfa/ITRP_Charge.pdf to the International Technology Recommendation Panel appointed by ICFA" (2 paragraphs).

METHOD OF SOFTWARE-BASED COMPENSATION OF TECHNOLOGICAL VARIATION IN CHROMATICITY COORDINATES OF LCD PANELS

Directory of Open Access Journals (Sweden)

I. O. Zharinov

2015-05-01

Full Text Available Subject of research. The problem of software-based compensation of technological variation in chromaticity coordinates of liquid crystal panels is considered. A method of software-based compensation of technological variation in chromaticity coordinates is proposed. The method provides the color reproduction characteristics of the series-produced samples on-board indication equipment corresponding to the sample equipment, which is taken as the standard. Method. Mathematical calculation of the profile is performed for the given model of the liquid crystal panel. The coefficients that correspond to the typical values of the chromaticity coordinates for the vertices of the triangle color coverage constitute a reference mathematical model of the plate LCD panel from a specific manufacturer. At the stage of incoming inspection the sample of the liquid crystal panel, that is to be implemented within indication equipment, is mounted on the lighting test unit, where Nokia-Test control is provided by the formation of the RGB codes for display the image of a homogeneous field in the red, green, blue and white. The measurement of the (x,y-chromaticity coordinates in red, green, blue and white colors is performed using a colorimeter with the known value of absolute error. Instead of using lighting equipment, such measurements may be carried out immediately on the sample indication equipment during customizing procedure. The measured values are used to calculate individual LCD-panel profile coefficients through the use of Grassman's transformation, establishing mutual relations between the XYZ-color coordinates and RGB codes to be used for displaying the image on the liquid crystal panel. The obtained coefficients are to be set into the memory of the graphics controller together with the functional software and then used for image displaying. Main results. The efficiency of the proposed method of software-based compensation for technological variation of

Panel Session

DEFF Research Database (Denmark)

Bertelsen, Olav Wedege

2004-01-01

In this panel session, four researchers will discuss the role of a theoretical foundation, in particular AT, in the design of information technology based artefacts. The general discussion will take of from a specific examination of the ActAD approach.......In this panel session, four researchers will discuss the role of a theoretical foundation, in particular AT, in the design of information technology based artefacts. The general discussion will take of from a specific examination of the ActAD approach....

Stress corrosion cracking susceptibility of steam generator tube materials in AVT (all volatile treatment) chemistry contaminated with lead

International Nuclear Information System (INIS)

Gomez Briceno, D.; Castano, M.L.; Garcia, M.S.

1996-01-01

Alloy 600 steam generator tubing has shown a high susceptibility to stress corrosion degradation at the operation conditions of pressurized water reactors. Several contaminants, such as lead, have been postulated as being responsible for producing the secondary side stress corrosion cracking that has occurred mainly at the location where these contaminants can concentrate. An extensive experimental work has been carried out in order to better understand the effects of lead on the stress corrosion cracking susceptibility of steam generator tube materials, namely Alloys 600, 690 and 800. This paper presents the experimental work conducted with a view to determining the influence of lead oxide concentration in AVT (all volatile treatment) conditions on the stress corrosion resistance of nickel alloys used in the fabrication of steam generator tubing. (orig.)

NANO-BATTERY TECHNOLOGY FOR EV-HEV PANEL: A PIONEERING STUDY

Directory of Open Access Journals (Sweden)

Ataur Rahman

2015-11-01

Full Text Available Global trends toward CO2 reduction and resource efficiency have significantly increased the importance of lightweight materials for automobile original equipment manufacturers (OEM. CO2 reduction is a fundamental driver for a more lightweight automobile. The introduction of Electrical Vehicles (EVs is one initiative towards this end. However EVs are currently facing several weaknesses: limited driving range, battery pack heaviness, lack of safety and thermal control, high cost, and overall limited efficiency. This study presents a panel-style nano-battery technology built into an EV with CuO filler solid polymer electrolyte (SPE sandwiched by carbon fiber (CF and lithium (Li plate. In addition to this, an aluminum laminated polypropylene film is used as the electromagnetic compatibility (EMC shield. The proposed battery body panel of the EV would reduce the car weight by about 20%, with a charge and discharge capacity of 1.5 kWh (10% of car total power requirement, and provide the heat insulation for the car which would save about 10% power consumption of the air conditioning system. Therefore, the EV would be benefited by 30% in terms of energy reduction by using the proposed body. Furthermore, the proposed body is considered environmental-friendly since it is recyclable for use in a new product. However, the main limiting factors of the SPE are its thermal behavior and moderate ionic conductivity at low temperatures. The SPE temperature is maintained by controlling the battery panel charging/discharge rate. It is expected that the proposed panel-style nano-battery use in an EV would save up to 6.00 kWh in battery energy, equivalent to 2.81 liters of petrol and prevent 3.081 kg of CO2 emission for a travel distance of 100 km. KEYWORDS: epoxy resin; carbon fiber; lithium thin plate; energy generation; solid electrolyte battery

Prof. Cristoforo Benvenuti stands in front of solar panels installed on the roof of Geneva airport. These panels, produced by the commpany SRB, are based on a technology developed at CERN by Cristoforo Benvenuti.

CERN Document Server

Maximilien Brice

2012-01-01

Prof. Cristoforo Benvenuti stands in front of solar panels installed on the roof of Geneva airport. These panels, produced by the commpany SRB, are based on a technology developed at CERN by Cristoforo Benvenuti.

Comparative performance of PV panels of different technologies over one year of exposure: Application to a coastal Mediterranean region of Algeria

International Nuclear Information System (INIS)

Guenounou, A.; Malek, A.; Aillerie, M.

2016-01-01

Highlights: • Performances of four PV panels of various technologies are compared during one year of exposure under natural outdoor conditions. • An original platform and methodology of test allow a real-time scan of several PV panel parameters. • The technologies compared are micromorph silicon, monocrystalline silicon, amorphous silicon, polycrystalline silicon. • The performance ratio point out a difference of behavior between the four technologies over one year. • Results are directly exploitable in costal regions of Mediterranean countries. - Abstract: The aim of this contribution is to compare the performance of four PV panels of different technologies for one year of exposure under natural outdoor conditions of a coastal region in the southern shore of the Mediterranean Sea. An original platform of test, especially dedicated for this study is presented describing operations and techniques used for measurements of the pertinent experimental data and for their exploitation. The four panel technologies studied are micromorph silicon (μ-Si), monocrystalline silicon (M-Si), amorphous silicon (a-Si) and polycrystalline silicon (Poli-Si). Two types of results are analyzed and presented. The first type is straight forwardly linked to the PV panels standard data calculated experimentally from measurements recorded during one year of exposure and compared with the values provided by the manufacturers in their datasheets. The second type is related to the energy yield in which the corresponding monthly and annual performance ratios of the four PV panels is calculated in two ways, using 1 – the datasheet’s value of Power Max, and 2 – the data providing from experimental campaign. In addition to the general conclusions concerning the fundamental role of the experimental study at a natural site for a good sizing of a renewable energy production system, we extend the analysis and discussion for the specific localization case of southern coastal region of

Optical Encoding Technology for Viral Screening Panels Final Report CRADA No TC02132.0

Energy Technology Data Exchange (ETDEWEB)

Lenhoff, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haushalter, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-08-15

This was a collaborative effort between Lawrence Livermore National Security, LLC, Lawrence Livermore National Laboratory (LLNL) and Parallel Synthesis Technologies, Inc. (PSTI), to develop Optical Encoding Technology for Viral Screening Panels. The goal for this effort was to prepare a portable bead reader system that would enable the development of viral and bacterial screening panels which could be used for the detection of any desired set of bacteria or viruses in any location. The main objective was to determine if the combination of a bead-based, PCR suspension array technology, formulated from Parallume encoded beads and PSTI’s multiplex assay reader system (MARS), could provide advantages in terms of the number of simultaneously measured samples, portability, ruggedness, ease of use, accuracy, precision or cost as compared to the Luminexbased system developed at LLNL. The project underwent several no cost extensions however the overall goal of demonstrating the utility of this new system was achieved. As a result of the project a significant change to the type of bead PSTI used for the suspension system was implemented allowing better performance than the commercial Luminex system.

Paneling architectural freeform surfaces

KAUST Repository

Eigensatz, Michael; Kilian, Martin; Schiftner, Alexander; Mitra, Niloy J.; Pottmann, Helmut; Pauly, Mark

2010-01-01

with a selected technology at reasonable cost, while meeting the design intent and achieving the desired aesthetic quality of panel layout and surface smoothness. The production of curved panels is mostly based on molds. Since the cost of mold fabrication

Analysing Production Technology and Risk in Organic and Conventional Dutch Arable Farming using Panel Data

NARCIS (Netherlands)

Gardebroek, C.; Chavez Clemente, M.D.; Oude Lansink, A.G.J.M.

2010-01-01

Abstract This paper compares the production technology and production risk of organic and conventional arable farms in the Netherlands. Just–Pope production functions that explicitly account for output variability are estimated using panel data of Dutch organic and conventional farms. Prior

Technological change and salary variation in Mexican regions: Analyzing panel data for the service sector

Directory of Open Access Journals (Sweden)

Mario Camberos C.

2013-07-01

Full Text Available In this paper Hypothesis Biased Technological Change is applied for Mexican workers services sector, belonging several Mexican regions. Economics Census microdata, 1998, 2003 and 2008 are used. Hypothesis is proved with technological gaps, under consideration of different index and result statistics consistency by taking account panel analysis. Mayor wages differences at 2008 year were find out between Capital region and South one, about five hundred percent on 1998 year; but it was lower on 2008, two hundred percent. This result is in correspondence with diminishing technological gap, perhaps caused by economic crisis impact.

On performing of interference technique based on self-adjusting Zernike filters (SA-AVT method) to investigate flows and validate 3D flow numerical simulations

Science.gov (United States)

Pavlov, Al. A.; Shevchenko, A. M.; Khotyanovsky, D. V.; Pavlov, A. A.; Shmakov, A. S.; Golubev, M. P.

2017-10-01

We present a method for and results of determination of the field of integral density in the structure of flow corresponding to the Mach interaction of shock waves at Mach number M = 3. The optical diagnostics of flow was performed using an interference technique based on self-adjusting Zernike filters (SA-AVT method). Numerical simulations were carried out using the CFS3D program package for solving the Euler and Navier-Stokes equations. Quantitative data on the distribution of integral density on the path of probing radiation in one direction of 3D flow transillumination in the region of Mach interaction of shock waves were obtained for the first time.

Panel 2.18: logistics, information technology (IT), and telecommunications in crisis management.

Science.gov (United States)

De Silva, Terrence; Chikersal, Jyotsna; Snoad, Nigel; Woodworth, Brent; Ghaly, Cherif; Catterall, Martin

2005-01-01

This is a summary of the presentations and discussion of Panel 2.18, Logistics, Information Technology, and Telecommunications in Crisis Management of the Conference, Health Aspects of the Tsunami Disaster in Asia, convened by the World Health Organization (WHO) in Phuket, Thailand, 04-06 May 2005. The topics discussed included issues related to logistics, information technology (IT), and crisis communication pertaining to the responses to the damage created by the Tsunami. It is presented in the following major sections: (1) issues; (2) lessons learned; (3) what was done well; (4) what could have been done better; and (5) conclusions and recommendations. Each major section is presented in four sub-sections: (1) needs assessments; (2) coordination; (3) filling the gaps; and (4) capacity building.

Dynamics of FDI, Technological Transformation and Environmental Degradation in Developing Countries: A Panel Analysis

Directory of Open Access Journals (Sweden)

Farwa Amjad

2016-03-01

Full Text Available This paper examines the relationship between FDI, technology and environment with an assessment of aggregated relationship, by technical composition and the mode of technology transferability through FDI. A panel data for 19 developing countries has been used to for 14 years of data. The empirical results have suggested that FDI is the significant variable in explaining the carbon emission in developing countries followed by energy consumption and technology transformation. Our findings suggest that to manage both energy consumption and FDI flows via investment in research and development (RDY or energy efficiency demand to reduce CO2 emissions is not possible without stringent environmental regulations and without retaining the developing countries’ competitiveness.

Maximizing the Utility of the Serum Repository With Current Technologies and Recommendations to Meet Future Needs: Report of the Technical Panel.

Science.gov (United States)

Baird, Coleen P

2015-10-01

The Department of Defense Serum Repository (DoDSR) of the Armed Forces Health Surveillance Center (AFHSC), Silver Spring, Maryland, has over 55 million specimens. Over 80% of these specimens are linked to individual health data. In response to Congressional and Department of Defense (DoD) concern about toxic exposures of deployed Service members and rapidly developing laboratory capabilities that may identify those exposed, the AFHSC hosted two panels in 2013. The first, the Needs Panel, focused on assessing the needs of the DoD that may be met using the current DoDSR and an enhanced repository. The second panel, the Technical Panel, focused on identifying the emerging laboratory technologies that are or will be available to DoD public health workers and researchers. This report summarizes the recommendations of the Technical Panel, to include identified gaps in the ability of the current DoDSR to address questions of interest to the DoD, the availability of laboratory technology to address these needs, and the types and quality of specimens required from Service members possibly exposed. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

Paneling architectural freeform surfaces

KAUST Repository

Eigensatz, Michael

2010-07-25

The emergence of large-scale freeform shapes in architecture poses big challenges to the fabrication of such structures. A key problem is the approximation of the design surface by a union of patches, so-called panels, that can be manufactured with a selected technology at reasonable cost, while meeting the design intent and achieving the desired aesthetic quality of panel layout and surface smoothness. The production of curved panels is mostly based on molds. Since the cost of mold fabrication often dominates the panel cost, there is strong incentive to use the same mold for multiple panels. We cast the major practical requirements for architectural surface paneling, including mold reuse, into a global optimization framework that interleaves discrete and continuous optimization steps to minimize production cost while meeting user-specified quality constraints. The search space for optimization is mainly generated through controlled deviation from the design surface and tolerances on positional and normal continuity between neighboring panels. A novel 6-dimensional metric space allows us to quickly compute approximate inter-panel distances, which dramatically improves the performance of the optimization and enables the handling of complex arrangements with thousands of panels. The practical relevance of our system is demonstrated by paneling solutions for real, cutting-edge architectural freeform design projects.

Paneling architectural freeform surfaces

KAUST Repository

Eigensatz, Michael

2010-07-26

The emergence of large-scale freeform shapes in architecture poses big challenges to the fabrication of such structures. A key problem is the approximation of the design surface by a union of patches, socalled panels, that can be manufactured with a selected technology at reasonable cost, while meeting the design intent and achieving the desired aesthetic quality of panel layout and surface smoothness. The production of curved panels is mostly based on molds. Since the cost of mold fabrication often dominates the panel cost, there is strong incentive to use the same mold for multiple panels. We cast the major practical requirements for architectural surface paneling, including mold reuse, into a global optimization framework that interleaves discrete and continuous optimization steps to minimize production cost while meeting user-specified quality constraints. The search space for optimization is mainly generated through controlled deviation from the design surface and tolerances on positional and normal continuity between neighboring panels. A novel 6-dimensional metric space allows us to quickly compute approximate inter-panel distances, which dramatically improves the performance of the optimization and enables the handling of complex arrangements with thousands of panels. The practical relevance of our system is demonstrated by paneling solutions for real, cutting-edge architectural freeform design projects. © 2010 ACM.

Panel discussion

International Nuclear Information System (INIS)

Anon.

1980-01-01

The panel discussion at the 10th Allianz Forum on 'Technology and Insurance' dealt with the following topics: New technologies: energy conversion (coal, petroleum, natural gas, nuclear energy, solar energy); infrastructure (transport, data processing); basic products (metallic materials, chemical products, pharmaceutical products); integrated products (microprocessors, production line machines) as well as new risks: political; general economic (financing, market structure); insurance-related, dangers to persons and property; reduction of risks. (orig.) [de

Advanced solar panel designs

Science.gov (United States)

Ralph, E. L.; Linder, E.

1995-01-01

This paper describes solar cell panel designs that utilize new hgih efficiency solar cells along with lightweight rigid panel technology. The resulting designs push the W/kg and W/sq m parameters to new high levels. These new designs are well suited to meet the demand for higher performance small satellites. This paper reports on progress made on two SBIR Phase 1 contracts. One panel design involved the use of large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells of 19% efficiency combined with a lightweight rigid graphite fiber epoxy isogrid substrate configuration. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power level of 60 W/kg with a potential of reaching 80 W/kg. The second panel design involved the use of newly developed high efficiency (22%) dual junction GaInP2/GaAs/Ge solar cells combined with an advanced lightweight rigid substrate using aluminum honeycomb core with high strength graphite fiber mesh facesheets. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power of 105 W/kg and 230 W/sq m. This paper will address the construction details of the panels and an a analysis of the component weights. A strawman array design suitable for a typical small-sat mission is described for each of the two panel design technologies being studied. Benefits in respect to weight reduction, area reduction, and system cost reduction are analyzed and compared to conventional arrays.

Stressed skin panels

Energy Technology Data Exchange (ETDEWEB)

Anon

2001-07-01

Advantages and disadvantages of stressed skin panels, also known as structural insulated panels (SIPs), are discussed as material and labour-saving alternatives to traditional stick framing. Stressed skin panels are manufactured 'sandwich' assemblies with a rigid insulating polystyrene foam core, whose interior and exterior surfaces are bonded into panels. The skins distribute and carry the structural loading while the bonded foam core provides insulation and keeps the two skins aligned. Since there are fewer framing members, there is little thermal bridging and the R-value remains high. SIPs are usually manufactured in four feet by eight feet panels, although some manufacturers can produce panels up to eight feet by forty feet. SIPs are resource efficient as they use less wood than conventional framing (about 25 per cent less); can structurally cover large spans, requiring less supplementary framing. Use of SIPs eliminate the need for headers over small openings; provide the ability to nail anywhere; create less scrap and waste; lessen vulnerability to unfavourable weather and other job-site hazards, can reduce delays, and often can produce significant savings in material and labour costs. Limitations include the more complex approaches to plumbing and electrical systems, although this can be minimized by designers by incorporating much of the plumbing and electrical work on interior (non-panel) walls. Most stressed skin panels require one-half inch interior gypsum drywall. If become wet, stressed skin panels take a long time to dry out and may harbour mold growth. Larger stressed-skin panels used in floors and roofs, may require cranes or other machinery for handling because of their weight. Although not without some environmental impact, overall, stressed skin panels are judged to be a resource-efficient building technology with significant energy-efficiency benefits and distinct advantages over stick framing. 3 photos.

Analysis of 3-panel and 4-panel microscale ionization sources

International Nuclear Information System (INIS)

Natarajan, Srividya; Parker, Charles B.; Glass, Jeffrey T.; Piascik, Jeffrey R.; Gilchrist, Kristin H.; Stoner, Brian R.

2010-01-01

Two designs of a microscale electron ionization (EI) source are analyzed herein: a 3-panel design and a 4-panel design. Devices were fabricated using microelectromechanical systems technology. Field emission from carbon nanotube provided the electrons for the EI source. Ion currents were measured for helium, nitrogen, and xenon at pressures ranging from 10 -4 to 0.1 Torr. A comparison of the performance of both designs is presented. The 4-panel microion source showed a 10x improvement in performance compared to the 3-panel device. An analysis of the various factors affecting the performance of the microion sources is also presented. SIMION, an electron and ion optics software, was coupled with experimental measurements to analyze the ion current results. The electron current contributing to ionization and the ion collection efficiency are believed to be the primary factors responsible for the higher efficiency of the 4-panel microion source. Other improvements in device design that could lead to higher ion source efficiency in the future are also discussed. These microscale ion sources are expected to find application as stand alone ion sources as well as in miniature mass spectrometers.

Technological process and optimum design of organic materials vacuum pyrolysis and indium chlorinated separation from waste liquid crystal display panels

Energy Technology Data Exchange (ETDEWEB)

Ma, En; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

2013-12-15

Highlights: • The vacuum pyrolysis–vacuum chlorinated separation system was proposed to recover the waste LCD panel. • The system can recycle the whole waste LCD panels efficiently without negative effects to environment. • The 82.03% of the organic materials was reclaimed. All pyrolysis products can be utilized by a reasonable way. • The separation of indium was optimized by the central composite design (CCD) under response surface methodology (RSM). • The recovery ratio of indium was further increased to 99.97%. -- Abstract: In this study, a technology process including vacuum pyrolysis and vacuum chlorinated separation was proposed to convert waste liquid crystal display (LCD) panels into useful resources using self-design apparatuses. The suitable pyrolysis temperature and pressure are determined as 300 °C and 50 Pa at first. The organic parts of the panels were converted to oil (79.10 wt%) and gas (2.93 wt%). Then the technology of separating indium was optimized by central composite design (CCD) under response surface methodology (RSM). The results indicated the indium recovery ratio was 99.97% when the particle size is less than 0.16 mm, the weight percentage of NH{sub 4}Cl to glass powder is 50 wt% and temperature is 450 °C. The research results show that the organic materials, indium and glass of LCD panel can be recovered during the recovery process efficiently and eco-friendly.

Flat-panel detectors in x-ray diagnosis

International Nuclear Information System (INIS)

Spahn, M.; Heer, V.; Freytag, R.

2003-01-01

For all application segments X-ray systems with flat-panel detectors increasingly enter the market. In digital radiography, mammography and cardiologic angiography flat-panel detectors are already well established while they are made ready for market introduction in general angiography and fluoroscopy. Two flat-panel detector technologies are available. One technology is based on an indirect conversion process of X-rays while the other one uses a direct conversion method.For radiography and dynamic applications the indirect method provides substantial advantages, while the direct method has some benefits for mammography. In radiography and mammography flat-panel detectors lead to clear improvements with respect to workflow, image quality and dose reduction potentials. These improvements are fostered by the immediate availability of the image, the large dynamic range and the high sensitivity to X-rays. New applications and the use of complex image processing algorithms have the potential to enlarge the present diagnostic range of applications.Up to now, image intensifiers are still the well-established technology for angiography and fluoroscopy. Nevertheless flat-panel detectors begin to enter this field, especially in cardiologic angiography.Characteristics of flat-panel detectors such as the availability of distortion-free images, the excellent contrast resolution, the large dynamic range, the high sensitivity to X-rays and the usability in magnetic fields provide the basis for improved and new diagnostic and interventional methods. (orig.) [de

Statics and buckling problems of aircraft structurally-anisotropic composite panels with the influence of production technology

Science.gov (United States)

Gavva, L. M.; Endogur, A. I.

2018-02-01

The mathematical model relations for stress-strain state and for buckling investigation of structurally-anisotropic panels made of composite materials are presented. The mathematical model of stiffening rib being torsioned under one-side contact with the skin is refined. One takes into account the influence of panel production technology: residual thermal stresses and reinforcing fibers preliminary tension. The resolved eight order equation and natural boundary conditions are obtained with variation Lagrange procedure. Exact analytical solutions for edge problems are considered. Computer program package is developed using operating MATLAB environment. The influence of the structure parameters on the level of stresses, displacements, of critical buckling forces for bending and for torsion modes has analyzed.

High Performance OLED Panel and Luminaire

Energy Technology Data Exchange (ETDEWEB)

Spindler, Jeffrey [OLEDWorks LLC, Rochester, NY (United States)

2017-02-20

In this project, OLEDWorks developed and demonstrated the technology required to produce OLED lighting panels with high energy efficiency and excellent light quality. OLED panels developed in this program produce high quality warm white light with CRI greater than 85 and efficacy up to 80 lumens per watt (LPW). An OLED luminaire employing 24 of the high performance panels produces practical levels of illumination for general lighting, with a flux of over 2200 lumens at 60 LPW. This is a significant advance in the state of the art for OLED solid-state lighting (SSL), which is expected to be a complementary light source to the more advanced LED SSL technology that is rapidly replacing all other traditional forms of lighting.

Propulsion Systems Panel deliberations

Science.gov (United States)

Bianca, Carmelo J.; Miner, Robert; Johnston, Lawrence M.; Bruce, R.; Dennies, Daniel P.; Dickenson, W.; Dreshfield, Robert; Karakulko, Walt; Mcgaw, Mike; Munafo, Paul M.

1993-01-01

The Propulsion Systems Panel was established because of the specialized nature of many of the materials and structures technology issues related to propulsion systems. This panel was co-chaired by Carmelo Bianca, MSFC, and Bob Miner, LeRC. Because of the diverse range of missions anticipated for the Space Transportation program, three distinct propulsion system types were identified in the workshop planning process: liquid propulsion systems, solid propulsion systems and nuclear electric/nuclear thermal propulsion systems.

Overview of autoventing turbine technology development project

International Nuclear Information System (INIS)

Waldrop, W.R.

1991-01-01

This paper reports on low concentrations of dissolved oxygen (DO) in the discharge of hydro plants which represents one of the most significant environmental concerns confronting the hydropower industry. This is especially of concern to utilities attempting to relicense older plants and to build new facilities. One method which shows promise is the autoventing turbine (AVT). The concept of an AVT involves air to be aspirated into the water as it passes through the turbine whenever concentrations of DO are less than desired. Because of this simple and natural process of aeration, the AVT promises to be more cost efficient and reliable than any of the other techniques. This has been demonstrated through experimentation at TVA's Norris Dam. An applied research project is being conducted to develop experimental and numerical methods to allow for reliable design and deployment of this new environmentally improved hydroturbine. TVA is providing overall coordination for this research which is being performed cooperatively with the U.S. Army Corps of Engineers, the U.S. Bureau of Reclamation, and the Iowa Institute of Hydraulic Research. This applied research project is fully integrated with a scale model test program jointly supported and conducted by TVA and Voith Hydro to test alternative locations for venting air into replacement turbine runners for Norris Dam

Delamination tolerance studies in laminated composite panels

Indian Academy of Sciences (India)

Abstract. Determination of levels of tolerance in delaminated composite panels is an important issue in composite structures technology. The primary intention is to analyse delaminated composite panels and estimate Strain. Energy Release Rate (SERR) parameters at the delamination front to feed into acceptability criteria.

Global status of recycling waste solar panels: A review.

Science.gov (United States)

Xu, Yan; Li, Jinhui; Tan, Quanyin; Peters, Anesia Lauren; Yang, Congren

2018-05-01

With the enormous growth in the development and utilization of solar-energy resources, the proliferation of waste solar panels has become problematic. While current research into solar panels has focused on how to improve the efficiency of the production capacity, the dismantling and recycling of end-of-life (EOL) panels are seldom considered, as can be seen, for instance, in the lack of dedicated solar-panel recycling plants. EOL solar-panel recycling can effectively save natural resources and reduce the cost of production. To address the environmental conservation and resource recycling issues posed by the huge amount of waste solar panels regarding environmental conservation and resource recycling, the status of the management and recycling technologies for waste solar panels are systemically reviewed and discussed in this article. This review can provide a quantitative basis to support the recycling of PV panels, and suggests future directions for public policy makers. At present, from the technical aspect, the research on solar panel recovery is facing many problems, and we need to further develop an economically feasible and non-toxic technology. The research on solar photovoltaic panels' management at the end of life is just beginning in many countries, and there is a need for further improvement and expansion of producer responsibility. Copyright © 2018 Elsevier Ltd. All rights reserved.

Integrated thermal treatment systems study. Internal review panel report

International Nuclear Information System (INIS)

Cudahy, J.; Escarda, T.; Gimpel, R.

1995-04-01

The U.S. Department of Energy (DOE) Office of Technology Development (OTD) commissioned two studies to evaluate nineteen thermal treatment technologies for treatment of DOE mixed low-level waste. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the help of the DOE Office of Environmental Management (EM) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel to review and comment on the ITTS studies. This Panel was composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency, the California EPA, and private experts. The Panel met from November 15-18, 1994 to review the ITTS studies and to make recommendations on the most promising thermal treatment systems for DOE mixed low-level wastes and on research and development necessary to prove the performance of the technologies. This report describes the findings and presents the recommendations of the Panel

Advanced Solar Panel Designs

Science.gov (United States)

Ralph, E. L.; Linder, E. B.

1995-01-01

Solar panel designs that utilize new high-efficiency solar cells and lightweight rigid panel technologies are described. The resulting designs increase the specific power (W/kg) achievable in the near-term and are well suited to meet the demands of higher performance small satellites (smallsats). Advanced solar panel designs have been developed and demonstrated on two NASA SBIR contracts at Applied Solar. The first used 19% efficient, large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells with a lightweight rigid graphite epoxy isogrid substrate configuration. A 1,445 sq cm coupon was fabricated and tested to demonstrate 60 W/kg with a high potential of achieving 80 W/kg. The second panel design used new 22% efficiency, dual-junction GaInP2/GaAs/Ge solar cells combined with a lightweight aluminum core/graphite fiber mesh facesheet substrate. A 1,445 sq cm coupon was fabricated and tested to demonstrate 105 W/kg with the potential of achieving 115 W/kg.

Expert panel evaluation of health information technology effects on adverse events.

Science.gov (United States)

Abramson, Erika L; Kern, Lisa M; Brenner, Samantha; Hufstader, Meghan; Patel, Vaishali; Kaushal, Rainu

2014-08-01

Adverse events (AEs) among hospitalized patients occur frequently and result in significant sequelae. Federal policy is incentivizing health information technology (HIT) use, although research demonstrating safety benefits from HIT is mixed. Our objective was to evaluate the potential effects of HIT on reducing 21 different inpatient AEs. Identifying AEs most likely to be reduced by HIT can inform the design of future studies evaluating its effectiveness. We conducted a modified Delphi panel of national experts in HIT and safety. We conducted a focused literature review to inform the experts. Using a novel framework, experts rated each AE as 'definitely reduced by health IT,' 'possibly reduced by health IT' and 'not likely to be reduced by health IT'. From our panel discussion, experts identified six AEs as 'definitely reduced by health IT': (1) adverse drug events (ADEs) associated with digoxin; (2) ADE associated with IV heparin; (3) ADE associated with hypoglycaemic agents; (4) ADE associated with low molecular weight heparin and factor Xa inhibitor; (5) contrast nephropathy associated with catheter angiography; and (6) ADE hospital-acquired antibiotic-associated Clostridium difficile. Understanding the effects of HIT on patient outcomes will be essential to ensuring that the significant federal investment results in anticipated improvements. This study serves as an important early step in helping with the design of future work evaluating level of HIT infrastructure and rates of inpatient AEs. © 2014 John Wiley & Sons, Ltd.

Report of the Federal Internetworking Requirements Panel

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-05-31

The Federal Internetworking Requirements Panel (FIRP) was established by the National Institute of Standards and Technology (NIST) to reassess Federal requirements for open systems networks and to recommend policy on the Government`s use of networking standards. The Panel was chartered to recommend actions which the Federal Government can take to address the short and long-term issues of interworking and convergence of networking protocols--particularly the Internet Protocol Suite (IPS) and Open Systems Interconnection (OSI) protocol suite and, when appropriate, proprietary protocols. The Panel was created at the request of the Office of Management and Budget in collaboration with the Federal Networking Council and the Federal Information Resources Management Policy Council. The Panel`s membership and charter are contained in an appendix to this report.

New Technology Demonstration Program - Results of an Attempted Field Test of Multi-Layer Light Polarizing Panels in an Office Space

Energy Technology Data Exchange (ETDEWEB)

Richman, Eric E.

2001-06-14

An assessment of the potential energy savings associated with the use of multi-layer light polarizing panels in an office space was initiated as part of the Department of Energy's (DOE) Federal Energy Management Program (FEMP) New Technology Demonstration Program (NTDP) in 1997. This project was intended to provide information on the effectiveness and application of this technology that could help federal energy managers and other interested individuals determine whether this technology had benefits for their occupied spaces. The use of an actual working office area provided the capability of evaluating the technology's effectiveness in the real world.

Model tests for the evaluation of auto-venting hydroturbines

International Nuclear Information System (INIS)

March, P.A.; Ragsdale, B.G.

1991-01-01

The most significant environment problems for many hydroelectric facilities is the quality of turbine discharges. The primary water quality problem is often low dissolved oxygen levels which occur seasonally. Relicensing or rehabilitation of a hydroelectric facility offers an opportunity to address environmental and industrial development concerns over dissolved oxygen levels and other water quality regulations which affect hydropower releases. The AVT represents a promising technology for improving the quality of hydropower releases in a cost-effective manner. This paper describes model studies in progress by the Tennessee Valley Authority (TVA) and Voith Hydro for the development of AVT technology

JTEC Panel report on electronic manufacturing and packaging in Japan

Science.gov (United States)

Kelly, Michael J.; Boulton, William R. (Editor); Kukowski, John; Meieran, Gene; Pecht, Michael; Peeples, John; Tummala, Rao; Dehaemer, Michael J.; Holdridge, Geoff (Editor); Gamota, George

1995-01-01

This report summarizes the status of electronic manufacturing and packaging technology in Japan in comparison to that in the United States, and its impact on competition in electronic manufacturing in general. In addition to electronic manufacturing technologies, the report covers technology and manufacturing infrastructure, electronics manufacturing and assembly, quality assurance and reliability in the Japanese electronics industry, and successful product realization strategies. The panel found that Japan leads the United States in almost every electronics packaging technology. Japan clearly has achieved a strategic advantage in electronics production and process technologies. Panel members believe that Japanese competitors could be leading U.S. firms by as much as a decade in some electronics process technologies.

Development of Electrostatically Clean Solar Array Panels

Science.gov (United States)

Stern, Theodore G.

2000-01-01

Certain missions require Electrostatically Clean Solar Array (ECSA) panels to establish a favorable environment for the operation of sensitive scientific instruments. The objective of this program was to demonstrate the feasibility of an ECSA panel that minimizes panel surface potential below 100mV in LEO and GEO charged particle environments, prevents exposure of solar cell voltage and panel insulating surfaces to the ambient environment, and provides an equipotential, grounded structure surrounding the entire panel. An ECSA panel design was developed that uses a Front Side Aperture-Shield (FSA) that covers all inter-cell areas with a single graphite composite laminate, composite edge clips for connecting the FSA to the panel substrate, and built-in tabs that interconnect the FSA to conductive coated coverglasses using a conductive adhesive. Analysis indicated the ability of the design to meet the ECSA requirements. Qualification coupons and a 0.5m x 0.5m prototype panel were fabricated and tested for photovoltaic performance and electrical grounding before and after exposure to acoustic and thermal cycling environments. The results show the feasibility of achieving electrostatic cleanliness with a small penalty in mass, photovoltaic performance and cost, with a design is structurally robust and compatible with a wide range of current solar panel technologies.

Gene panel testing for inherited cancer risk.

Science.gov (United States)

Hall, Michael J; Forman, Andrea D; Pilarski, Robert; Wiesner, Georgia; Giri, Veda N

2014-09-01

Next-generation sequencing technologies have ushered in the capability to assess multiple genes in parallel for genetic alterations that may contribute to inherited risk for cancers in families. Thus, gene panel testing is now an option in the setting of genetic counseling and testing for cancer risk. This article describes the many gene panel testing options clinically available to assess inherited cancer susceptibility, the potential advantages and challenges associated with various types of panels, clinical scenarios in which gene panels may be particularly useful in cancer risk assessment, and testing and counseling considerations. Given the potential issues for patients and their families, gene panel testing for inherited cancer risk is recommended to be offered in conjunction or consultation with an experienced cancer genetic specialist, such as a certified genetic counselor or geneticist, as an integral part of the testing process. Copyright © 2014 by the National Comprehensive Cancer Network.

Temperature and Solar Radiation Effects on Photovoltaic Panel Power

OpenAIRE

Karafil, Akif; Ozbay, Harun; Kesler, Metin

2016-01-01

Solar energy is converted to electrical energy directly by semi-conductors materials used in Photovoltaic (PV) panels. Although, there has been great advancements in semi-conductor material technology in recent years panel efficiency is very lower. There are many factors affecting the panel efficiency such as tilt angle, shading, dust, solar radiation level, temperature and wiring losses. Among these factors, solar radiation level and temperature are more prominent. The solar radiation level ...

VES PANEL (by invitation): Advancement and Enhanced Integration of Digital Technology Systems, VR Applications, CPS-Systems and Tools for Design Engineering

NARCIS (Netherlands)

Wendrich, Robert E.; Lim, Theodore; Baalsrud Hauge, Jannicke; Vitali, Andrea

2018-01-01

The purpose of this VES panel is to encourage discussion and exchange of views about current and new trends for Virtual and Immersive/Blended Systems and the transference of knowledge over multiple domains. As the market and/or industrial interest in virtual environments increase, new technologies

Innovation for a better life: IdeaSquare to host a panel discussion for the 2016 Millennium Technology Prize

CERN Multimedia

Antonella Del Rosso

2015-01-01

The one-million-euro Millennium Technology Prize promotes technological innovations that improve the quality of people’s lives. A series of panel discussions are being held worldwide to draw attention to the themes of the prize and to promote nominations for high-calibre candidates for the 2016 award. For the first time, IdeaSquare has been chosen as one of the venues and CERN people are invited to take part. Save the date: 30 June, 3 p.m.   The Millennium Technology Prize was established in 2004 by the Technology Academy Finland (TAF), an independent foundation whose mission is “to promote innovations that improve the quality of people’s lives in a sustainable manner”. Awarded every other year, the prize has already recognised the work of seven great innovators who developed technological innovations to tackle the great challenges of mankind: learning, health and a clean environment. The first prize was awarded to Tim Berners-Lee for the World Wide Web. E...

The Atomic Safety and Licensing Board Panel

International Nuclear Information System (INIS)

1998-01-01

Through the Atomic Energy Act, Congress made is possible for the public to get a full and fair hearing on civilian nuclear matters. Individuals who are directly affected by any licensing action involving a facility producing or utilizing nuclear materials may participate in a formal hearing, on the record, before independent judges on the Atomic Safety and Licensing Board Panel (ASLBP or Panel). Frequently, in deciding whether a license, permit, amendment, or extension should be granted to a particular applicant, the Panel members must be more than mere umpires. If appropriate, they are authorized to go beyond the issues the parties place before them in order to identify, explore, and resolve significant questions involving threats to the public health and safety that come to a board's attention during the proceedings. This brochure explains the purpose of the panel. Also addressed are: type of hearing handled; method of public participation; formality of hearings; high-level waste; other panel responsibilities and litigation technology

Ultrafast Thermal Cycling of Solar Panels

National Research Council Canada - National Science Library

Wall, T

1998-01-01

Two new cyclers that utilize a novel hybrid approach to perform fast thermal cycling of solar panels have been built and are now operational in the Mechanics and Materials Technology Center at The Aerospace Corporation...

3rd Annual Disruptive Technology Conference

Science.gov (United States)

2006-09-07

Panel -- The Warfighter’s Perspective The Impact of Disruptive Technologies on Joint Warfighting MG Michael Vane, USA, Vice Director for Force...Structure, Resources & Assessment, Joint Staff, J-8 Panel -- Perspectives of Change: Identifying the Emerging Commercial Disruptive Technologies Decision...Mark Lucas, Board Member OSGeo, RadiantBlue Technologies Panel -- The Search for Disruptive Technologies - a “Blue Force” Multiplier Advanced

Exploring changes in nursing students' attitudes towards the use of technology: A four-wave longitudinal panel study.

Science.gov (United States)

Tubaishat, Ahmad; Aljezawi, Ma'en; Al-Rawajfah, Omar M; Habiballah, Laila; Akhu-Zaheya, Laila M

2016-03-01

It is essential for nursing students to be equipped with the necessary technology skills throughout and after their study period. Their acceptance of this technology depends largely on their attitudes towards technology. To explore the evolution in nursing students' attitudes towards technology, and to determine whether there was a change in participants' formal education in technology over their four years of study. A longitudinal panel study was conducted in a single school of nursing in Jordan. A total of 140 students were followed over their four years of undergraduate study. They completed the same tool (the Technology Attitude Scale) each year, to capture any changes in their attitudes towards technology across the years. In all four waves of data collection, students showed positive attitudes towards technology, with the highest attitude scores being in their final year (M=6.19, SD=0.72). As the students spent more time on their nursing education, they were found to have a more positive attitude. Thus, a strong positive relationship existed between this formal education in technology and attitudes: as the students' education in technology increased, their attitudes were more positive. A remarkable development in students' attitudes towards technology is reported in this study. The positive attitudes displayed by the students should be enhanced by providing technology-related subjects during their studies in nursing schools at a very early stage. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of OLED and edge-lit LED lighting panels

Science.gov (United States)

Mou, Xi; Narendran, Nadarajah; Zhu, Yiting; Freyssinier, Jean Paul

2016-09-01

Solid-state lighting (SSL) offers a new technology platform for lighting designers and end-users to illuminate spaces with low energy demand. Two types of SSL sources include organic light-emitting diodes (OLEDs) and light-emitting diodes (LEDs). OLED is an area light source, and its primary competing technology is the edge-lit LED panel. Generally, both of these technologies are considered similar in shape and appearance, but there is little understanding of how people perceive discomfort glare from large area light sources. The objective of this study was to evaluate discomfort glare for the two lighting technologies under similar operating conditions by gathering observers' reactions. The human factors study results showed no statistically significant difference in human response to discomfort glare between OLED and edge-lit LED panels when the two light sources produced the same lighting stimulus. This means both technologies appeared equally glary beyond a certain luminance.

BWR plant advanced central control panel PODIA

International Nuclear Information System (INIS)

Fujii, K.; Hayakawa, H.; Ikeda, Y.; Neda, T.; Suto, O.; Takamiya, S.

1983-01-01

BWR plant central control panels have become more and more enlarged and complicated recently due to the magnification of the scale of a plant and the requirement to reinforce safety. So, it is important to make communication between men and the complicated central control panel smooth. Toshiba has developed an advanced central control panel, named PODIA, which uses many computers and color CRTs, and PODIA is now in the stage of application to practical plants. In this article, the writers first touch upon control functions transition in the central control room, the PODIA position concerning the world-wide trend in this technology phase and the human engineering on the design. Then they present concrete design concepts for the control board and computer system which constitute PODIA

Simulation study of air and water cooled photovoltaic panel using ANSYS

Science.gov (United States)

Syafiqah, Z.; Amin, N. A. M.; Irwan, Y. M.; Majid, M. S. A.; Aziz, N. A.

2017-10-01

Demand for alternative energy is growing due to decrease of fossil fuels sources. One of the promising and popular renewable energy technology is a photovoltaic (PV) technology. During the actual operation of PV cells, only around 15% of solar irradiance is converted to electricity, while the rest is converted into heat. The electrical efficiency decreases with the increment in PV panel’s temperature. This electrical energy is referring to the open-circuit voltage (Voc), short-circuit current (Isc) and output power generate. This paper examines and discusses the PV panel with water and air cooling system. The air cooling system was installed at the back of PV panel while water cooling system at front surface. The analyses of both cooling systems were done by using ANSYS CFX and PSPICE software. The highest temperature of PV panel without cooling system is 66.3 °C. There is a decrement of 19.2% and 53.2% in temperature with the air and water cooling system applied to PV panel.

Experimental and Numerical Research of the Thermal Properties of a PCM Window Panel

Directory of Open Access Journals (Sweden)

Martin Koláček

2017-07-01

Full Text Available This paper reports the experimental and simulation analysis of a window system incorporating Phase Change Materials (PCMs. In this study, the latent heat storage material is exploited to increase the thermal mass of the building component. A PCM-filled window can increase the possibilities of storage energy from solar radiation and reduce the heating cooling demand. The presented measurements were performed on a specific window panel that integrates a PCM. The PCM window panel consists of four panes of safety glass with three gaps, of which the first one contains a prismatic glass, the second a krypton gas, and the last one a PCM. New PCM window panel technology uses the placement of the PCM in the whole space of the window cavity. This technology improves the thermal performance and storage mass of the window panel. The results show the incongruent melting of salt hydrates and the high thermal inertia of the PCM window panel. The simulation data showed that the PCM window panel and the double glazing panel markedly reduced the peak temperature on the interior surface, reduced the air temperature inside the room, and also considerably improved the thermal mass of the building. This means that the heat energy entering the building through the panel is reduced by 66% in the summer cycle.

Planarity certification of ATLAS Micromegas detector panels

Energy Technology Data Exchange (ETDEWEB)

Mueller, Ralph; Biebel, Otmar; Bortfeldt, Jonathan; Flierl, Bernhard; Hertenberger, Ralf; Loesel, Philipp; Herrmann, Maximilian [LMU Muenchen (Germany); Zibell, Andre [JMU Wuerzburg (Germany)

2016-07-01

During the second long LHC shutdown, 2019/20, the precision tracking detectors of the ATLAS muon spectrometer in the inner end caps will be replaced using Micromegas, a planar gas-detector technology. Modules of 2 m{sup 2} area are built in quadruplets from five precisely planar sandwich panels that define the anodes and the cathodes of the four active detector planes. A panel is composed of three consecutive layers FR4 - aluminum honeycomb - FR4. Single plane spatial particle resolution below 100 μm is achievable when the deviations from planarity of the strip-anodes do not exceed 80 μm RMS over the whole active area and the parallelism of the readout strips is within 30 μm. In order to measure the dimensional accuracy of each panel, laser distance sensors combined with a coordinate measurement system have been investigated. The sensor requirements to measure the planarity of the panels are a resolution of 0.3 μm and a beam spot diameter of ∼20 μm, well below 100 μ m the size of the smallest structures. We report on achieved planarities of the panels and the performance of the laser sensor system. A panel with an RMS better than 30 μm was build and the evolution of its planarity due to humidity and temperature effects is shown.

Report of the DOE panel on low activation materials for fusion applications

International Nuclear Information System (INIS)

Conn, R.W.

1983-06-01

In February, 1982, the Office of Fusion Energy, DOE, through its Division of Development and Technology, established a Panel to examine materials with attractive radioactivation characteristics for applications in fusion power reactors. Since February, the Panel has met together and in subgroups numerous times. Input from knowledgeable people was elicited via a two day workshop held at UCLA in April, 1982. The agenda, titles of talks, and speakers are given in Appendix II. We present here a synopsis of the Panel's findings based upon both external information provided to us and upon the work and deliberations of the Panel itself. Conclusions and recommendations follow. Background technical information brought together by the Panel is relegated to Appendices III and IV

Information and communication technology

Science.gov (United States)

Edelson, Burton I.; Pelton, Joseph N.; Bostian, Charles W.; Brandon, William T.; Chan, Vincent W. S.; Hager, E. Paul; Helm, Neil R.; Jennings, Raymond D.; Kwan, Robert K.; Mahle, Christoph E.

1994-01-01

NASA and the National Science Foundation (NSF) commissioned a panel of U.S. experts to study the international status of satellite communications systems and technology. The study covers emerging systems concepts, applications, services, and the attendant technologies. The panel members traveled to Europe, Japan, and Russia to gather information firsthand. They visited 17 sites in Europe, 20 in Japan, and 4 in Russia. These included major manufacturers, government organizations, service providers, and associated research and development facilities. The panel's report was reviewed by the sites visited, by the panel, and by representatives of U.S. industry. The report details the information collected and compares it to U.S. activities.

Panel Analysis

DEFF Research Database (Denmark)

Brænder, Morten; Andersen, Lotte Bøgh

2014-01-01

Based on our 2013-article, ”Does Deployment to War Affect Soldiers' Public Service Motivation – A Panel Study of Soldiers Before and After their Service in Afghanistan”, we present Panel Analysis as a methodological discipline. Panels consist of multiple units of analysis, observed at two or more...... in research settings where it is not possible to distribute units of analysis randomly or where the independent variables cannot be manipulated. The greatest disadvantage in regard to using panel studies is that data may be difficult to obtain. This is most clearly vivid in regard to the use of panel surveys...... points in time. In comparison with traditional cross-sectional studies, the advantage of using panel studies is that the time dimension enables us to study effects. Whereas experimental designs may have a clear advantage in regard to causal inference, the strength of panel studies is difficult to match...

Interview with Dr Anna Matamala

Directory of Open Access Journals (Sweden)

Lucinea Marcelino Villela

2016-09-01

In this interview, which took place in June 2016, Dr Anna Matamala described some details about her long professional experience in Audiovisual Translation, especially in dubbing from English into Catalan, and we talked about many other things like her interest in lexicography, her point of view on some contemporary topics in Audiovisual Translation Studies: the use of technology, the relation between AVT and Accessibility Studies, AVT and Filmmaking fields, the importance of keeping in touch with other countries and even continents outside Europe, and she also gave some advice to the new generation of Translation students.

Interview with Dr Anna Matamala

Directory of Open Access Journals (Sweden)

Lucinea Marcelino Villela

2016-12-01

Full Text Available In this interview, which took place in June 2016, Dr Anna Matamala described some details about her long professional experience in Audiovisual Translation, especially in dubbing from English into Catalan, and we talked about many other things like her interest in lexicography, her point of view on some contemporary topics in Audiovisual Translation Studies: the use of technology, the relation between AVT and Accessibility Studies, AVT and Filmmaking fields, the importance of keeping in touch with other countries and even continents outside Europe, and she also gave some advice to the new generation of Translation students.

Application of solar panels in vehicle parking under the concept of distributed generation

International Nuclear Information System (INIS)

Calderon Vega, Jefferson

2013-01-01

An analysis of solar panels technologies is realized to implement an application of distributed generation in vehicle parking. The different technologies available in the market about solar panels are investigated. The climatological and geographical conditions are studied for the use of solar energy. The electrical requirements are determined for the implementation of solar panels as a distributed generation system. The benefit/cost is analyzed in establishments of vehicle parking for the implementation of solar panels. A photovoltaic system was developed in a vehicle parking attached at the Colegio Federado de Ingenieros y Arquitectos, and also the technical feasibility has been determined. The photovoltaic systems about roofs of buildings every day have been more viable, due that the cost of the systems has been lower and more efficient. Crystalline silicon ''mono'' or ''poly'' has been the most reliable option in the development of new technologies in solar cells. Costa Rica is found in a zone where the photovoltaic solar energy is harnessed and should to be fostered by the engineering sector. The installation of photovoltaic systems has contributed to reduce the carbon footprint in the distributed generation [es

WTEC panel report on European nuclear instrumentation and controls

International Nuclear Information System (INIS)

White, J.D.; Lanning, D.D.; Johnson, P.M.H.

1991-12-01

A study of instrumentation and controls (I and C) technology used in nuclear power plants in Europe was conducted by a panel of US specialists. This study plants in Europe was conducted by a panel of US specialists. This study included a review of the literature on the subject, followed by a visit to some of the leading organizations in Europe in the field nuclear I and C. Areas covered are: (1) role of the operator and control room design; (2) transition from analog to digital technology; (3) computerized operator support systems for fault management; (4) control strategies and techniques; (5) Nuclear power plant I and C architecture; (6) instrumentation and (7) computer standards and tools. The finding relate to poor reactions

75 FR 8427 - Civil Supersonic Aircraft Panel Discussion

Science.gov (United States)

2010-02-24

... entitled, ``State of the Art of Supersonics Aircraft Technology--What has progressed in science since 1973... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Civil Supersonic Aircraft Panel Discussion AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of meeting participation...

77 FR 61572 - Malcolm Baldrige National Quality Award Panel of Judges

Science.gov (United States)

2012-10-10

... composed of twelve members prominent in the fields of quality, innovation, and performance management and... Hertz, Director, Baldrige Performance Excellence Program, National Institute of Standards and Technology... Quality Award Panel of Judges AGENCY: National Institute of Standards and Technology, Department of...

76 FR 22675 - Malcolm Baldrige National Quality Award Panel of Judges

Science.gov (United States)

2011-04-22

... prominent in the fields of quality, innovation, and performance management and appointed by the Secretary of..., Director, Baldrige Performance Excellence Program, National Institute of Standards and Technology... Quality Award Panel of Judges AGENCY: National Institute of Standards and Technology, Department of...

Panel data specifications in nonparametric kernel regression

DEFF Research Database (Denmark)

Czekaj, Tomasz Gerard; Henningsen, Arne

parametric panel data estimators to analyse the production technology of Polish crop farms. The results of our nonparametric kernel regressions generally differ from the estimates of the parametric models but they only slightly depend on the choice of the kernel functions. Based on economic reasoning, we...

Seasonal expression of arginine vasotocin mRNA and its correlations to gonadal steroidogenic enzymes and sexually dimorphic coloration during sex reversal in the gilthead seabream (Sparus aurata).

Science.gov (United States)

Reyes-Tomassini, José J; Wong, Ten-Tsao; Zohar, Yonathan

2017-06-01

Arginine vasotocin is a hormone produced in the hypothalamus of teleost fish that has been shown to regulate gonad development and sexual behavior. To study the role of arginine vasotocin in the gonadal cycle of the hermaphrodite gilthead seabream, Sparus aurata, we cloned the seabream arginine vasotocin (avt) complementary DNA (cDNA). We investigated the expression of brain avt throughout the gonad cycle using real-time quantitative PCR and compared its expression levels to the expression levels of two key gonadal steroidogenic enzymes, cyp19a1a and cyp11b2. In July, when the process of sex reversal is thought to begin, avt expression was elevated over the previous 2 months. Avt in the brain remained at or above the level of July until November then peaked again in December. There was no difference between males and females in the expression levels of brain avt throughout the year. However, only in ambisexual fish was the expression of the cyp19a1a gonadal aromatase correlated to the expression of avt in the brain. Cyp11b2 did not show any correlation to brain avt expression. We also found that females had more intense body coloration than males and that this intensity peaked prior to spawning. Avt expression and female coloration were positively correlated. The fact that brain avt expression was lowest during gonad quiescence, together with the observation of a correlation between brain avt with gonadal cyp19a1a and body coloration during that time suggests that avt may play a role during the process of sex reversal and spawning of the gilthead seabream.

Re-active Passive (RAP) Devices for Control of Noise Transmission through a Panel

Science.gov (United States)

Carneal, James P.; Giovanardi, Marco; Fuller, Chris R.; Palumbo, Daniel L.

2008-01-01

Re-Active Passive (RAP) devices have been developed to control low frequency (transmission through a panel. These devices use a combination of active, re-active, and passive technologies packaged into a single unit to control a broad frequency range utilizing the strength of each technology over its best suited frequency range. The RAP device uses passive constrained layer damping to cover the relatively high frequency range (>200 Hz), reactive distributed vibration absorber) to cover the medium frequency range (75 to 250 Hz), and active control for controlling low frequencies (transmission through a panel mounted in a transmission loss test facility. Experimental results are presented for the bare panel, and combinations of passive treatment, reactive treatment, and active control. Results indicate that three RAP devices were able to increase the overall broadband (15-1000 Hz) transmission loss by 9.4 dB. These three devices added a total of 285 grams to the panel mass of 6.0 kg, or approximately 5%, not including control electronics.

2013 Advanced Environmental Health/Advanced Food Technology Standing Review Panel Final Report

Science.gov (United States)

Steinberg, Susan

2014-01-01

The 2013 Advanced Environmental Health/Advanced Food Technology (AEH/AFT) Standing Review Panel (from here on referred to as the SRP) participated in a WebEx/teleconference with members of the Space Human Factors and Habitability (SHFH) Element, representatives from the Human Research Program (HRP), and NASA Headquarters on November 22, 2013 (list of participants is in Section IX of this report). The SRP reviewed the updated research plans for the Risk of Adverse Health Effects Due to Alterations in Host-Microorganism Interactions (Host Microbe Risk) and the Risk of Performance Decrement and Crew Illness Due to an Inadequate Food System (Food Risk). The SRP also received a status update on the Risk of Adverse Health Effects of Exposure to Dust and Volatiles during Exploration of Celestial Bodies (Dust Risk). Overall, the SRP was impressed with the strong research plans presented by the scientists and staff associated with the SHFH Element. The SRP also thought that the updated research plans were thorough, well organized, and presented in a comprehensive manner. The SRP agrees with the changes made to the Host Microbe Risk and Food Risk portfolios and thinks that the targets for Gap closure are appropriate.

Vacuum insulation panels for building applications: A review and beyond

Energy Technology Data Exchange (ETDEWEB)

Baetens, Ruben [Department of Building Materials and Structures, SINTEF Building and Infrastructure, NO-7465 Trondheim (Norway); Department of Civil and Transport Engineering, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim (Norway); Laboratory of Building Physics, Department of Civil Engineering, Catholic University of Leuven (KUL), BE-3001 Heverlee (Belgium); Jelle, Bjoern Petter [Department of Building Materials and Structures, SINTEF Building and Infrastructure, NO-7465 Trondheim (Norway); Department of Civil and Transport Engineering, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim (Norway); Thue, Jan Vincent [Department of Civil and Transport Engineering, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim (Norway); Tenpierik, Martin J. [Faculty of Architecture, Urbanism and Building Sciences, Delft University of Technology, Julianalaan 134, 2628 BL Delft (Netherlands); Grynning, Steinar; Uvsloekk, Sivert [Department of Building Materials and Structures, SINTEF Building and Infrastructure, NO-7465 Trondheim (Norway); Gustavsen, Arild [Department of Architectural Design, History and Technology, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim (Norway)

2010-02-15

Vacuum insulation panels (VIPs) are regarded as one of the most promising high performance thermal insulation solutions on the market today. Thermal performances three to six times better than still-air are achieved by applying a vacuum to an encapsulated micro-porous material, resulting in a great potential for combining the reduction of energy consumption in buildings with slim constructions. However, thermal bridging due to the panel envelope and degradation of thermal performance through time occurs with current technology. Furthermore, VIPs cannot be cut on site and the panels are fragile towards damaging. These effects have to be taken into account for building applications as they may diminish the overall usability and thermal performance. This paper is as far as the authors know the first comprehensive review on VIPs. Properties, requirements and possibilities of foil encapsulated VIPs for building applications are studied based on available literature, emphasizing thermal bridging and degradation through time. An extension is made towards gas-filled panels and aerogels, showing that other high performance thermal insulation solutions do exist. Combining the technology of these solutions and others may lead to a new leap forward. Feasible paths beyond VIPs are investigated and possibilities such as vacuum insulation materials (VIMs) and nano insulation materials (NIMs) are proposed. (author)

Re-Active Passive devices for control of noise transmission through a panel

Science.gov (United States)

Carneal, James P.; Giovanardi, Marco; Fuller, Chris R.; Palumbo, Dan

2008-01-01

Re-Active Passive devices have been developed to control low-frequency (transmission through a panel. These devices use a combination of active, re-active, and passive technologies packaged into a single unit to control a broad frequency range utilizing the strength of each technology over its best suited frequency range. The Re-Active Passive device uses passive constrained layer damping to cover relatively high-frequency range (>150 Hz), reactive distributed vibration absorber to cover the medium-frequency range (50-200 Hz), and active control for controlling low frequencies (transmission through a panel mounted in the Transmission Loss Test Facility at Virginia Tech. Experimental results are presented for the bare panel, and combinations of passive treatment, reactive treatment, and active control. Results indicate that three Re-Active Passive devices were able to increase the overall broadband (15-1000 Hz) transmission loss by 9.4 dB. These three devices added a total of 285 g to the panel mass of 6.0 kg, or approximately 5%, not including control electronics.

Integrated Solar-Panel Antenna Array for CubeSats (ISAAC)

Data.gov (United States)

National Aeronautics and Space Administration — This project will develop a new subsystem technology for CubeSats. Integrated Solar-Panel Antenna Array for CubeSats (ISAAC) is an efficient, compact, high gain, low...

Advanced Ultrasupercritical (AUSC) Tube Membrane Panel Development

Energy Technology Data Exchange (ETDEWEB)

Pschirer, James [Alstom Power Inc., Windsor, CT (United States); Burgess, Joshua [Alstom Power Inc., Windsor, CT (United States); Schrecengost, Robert [Alstom Power Inc., Windsor, CT (United States)

2017-08-16

membrane panels,and performed simulated shop repairs on the panel fabricated using Grade 92. GE executed the program as the prime contractor under the direction of Principal Investigator Mr. James Pschirer. Other participants in this project included GE Boiler Engineering, GE Chattanooga Manufacturing, GE Materials Technology Center, GE Rocky Mountain Service Center, and a Technical Consultant from Electric Power Research Institute (EPRI).

Panel 4 - applications to transportation

Energy Technology Data Exchange (ETDEWEB)

Nichols, F. [Argonne National Lab., IL (United States); Au, J. [Sundstrand Aerospace, Rockford, IL (United States); Bhattacharya, R. [Universal Energy Systems, Inc., Dayton, OH (United States); Bhushan, B. [Ohio State Univ., Columbus (United States); Blunier, D. [Caterpillar, Inc., Peoria, IL (United States); Boardman, B. [Deere & Co., Moline, IL (United States); Brombolich, L. [Compu-Tec Engineering, Chesterfield, MO (United States); Davidson, J. [Vanderbilt Univ., Nashville, TN (United States); Graham, M. [Northwestern Univ., Evanston, IL (United States); Hakim, N. [Detroit Diesel Corp., MI (United States); Harris, K. [Dubbeldee Harris Diamond Corp., Mt. Arlington, NJ (United States); Hay, R. [Norton Diamond Film, Northboro, MA (United States); Herk, L. [Southwest Research Inst., Southfield, MI (United States); Hojnacki, H.; Rourk, D. [Intelligent Structures Incorporated, Canton, MI (United States); Kamo, R. [Adiabatics, Inc., Columbus, IN (United States); Nieman, B. [Allied-Signal Inc., Des Plaines, IL (United States); O`Neill, D. [3M, St. Paul, MN (United States); Peterson, M.B. [Wear Sciences, Arnold, MD (United States); Pfaffenberger, G. [Allison Gas Turbine, Indianapolis, IN (United States); Pryor, R.W. [Wayne State Univ., Detroit, MI (United States); Russell, J. [Superconductivity Publications, Inc., Somerset, NJ (United States); Syniuta, W. [Advanced Mechanical Technology, Inc., Newton, MA (United States); Tamor, M. [Ford Motor Co., Dearborn, MI (United States); Vojnovich, T. [Dept. of Energy, Washington, DC (United States); Yarbrough, W. [Pennsylvania State Univ., University Park (United States); Yust, C.S. [Oak Ridge National Lab., TN (United States)

1993-01-01

The aim of this group was to compile a listing of current and anticipated future problem areas in the transportation industry where the properties of diamond and DLC films make them especially attractive and where the panel could strongly endorse the establishment of DOE/Transportation Industry cooperative research efforts. This section identifies the problem areas for possible applications of diamond/DLC technology and presents indications of current approaches to these problems.

Status-Dependent Vasotocin Modulation of Dominance and Subordination in the Weakly Electric Fish Gymnotus omarorum

Directory of Open Access Journals (Sweden)

Rossana Perrone

2018-01-01

Full Text Available Dominant-subordinate status emerges from agonistic encounters. The weakly electric fish, Gymnotus omarorum, displays a clear-cut example of non-breeding territorial aggression. The asymmetry in the behavior of dominants and subordinates is outstanding. Dominants are highly aggressive and subordinates signal submission in a precise sequence of locomotor and electric traits: retreating, decreasing their electric organ discharge rate, and emitting transient electric signals. The hypothalamic neuropeptide arginine-vasotocin (AVT and its mammalian homolog arginine-vasopressin, are key modulators of social behavior, known to adapt their actions to different contexts. By analyzing the effects of pharmacological manipulations of the AVT system in both dominants and subordinates, we show evidence of distinct status-dependent actions of AVT. We demonstrate an endogenous effect of AVT on dominants' aggression levels: blocking the V1a AVT receptor induced a significant decrease in dominants' attack rate. AVT administered to subordinates enhanced the expression of the electric signals of submission, without affecting subordinates' locomotor displays. This study contributes a clear example of status-dependent AVT modulation of agonistic behavior in teleosts, and reveals distinctive activation patterns of the AVT system between dominants and subordinates.

Status-Dependent Vasotocin Modulation of Dominance and Subordination in the Weakly Electric Fish Gymnotus omarorum.

Science.gov (United States)

Perrone, Rossana; Silva, Ana C

2018-01-01

Dominant-subordinate status emerges from agonistic encounters. The weakly electric fish, Gymnotus omarorum , displays a clear-cut example of non-breeding territorial aggression. The asymmetry in the behavior of dominants and subordinates is outstanding. Dominants are highly aggressive and subordinates signal submission in a precise sequence of locomotor and electric traits: retreating, decreasing their electric organ discharge rate, and emitting transient electric signals. The hypothalamic neuropeptide arginine-vasotocin (AVT) and its mammalian homolog arginine-vasopressin, are key modulators of social behavior, known to adapt their actions to different contexts. By analyzing the effects of pharmacological manipulations of the AVT system in both dominants and subordinates, we show evidence of distinct status-dependent actions of AVT. We demonstrate an endogenous effect of AVT on dominants' aggression levels: blocking the V1a AVT receptor induced a significant decrease in dominants' attack rate. AVT administered to subordinates enhanced the expression of the electric signals of submission, without affecting subordinates' locomotor displays. This study contributes a clear example of status-dependent AVT modulation of agonistic behavior in teleosts, and reveals distinctive activation patterns of the AVT system between dominants and subordinates.

Vasotocin- and mesotocin-induced increases in short-circuit current across tree frog skin.

Science.gov (United States)

Takada, Makoto; Fujimaki-Aoba, Kayo; Hokari, Shigeru

2011-02-01

In adult amphibian skin, Na(+) crosses from outside to inside. This Na(+) transport can be measured as the amiloride-blockable short-circuit current (SCC) across the skin. We investigated the effects of arginine vasotocin (AVT) and mesotocin (MT), and those of antagonists of the vasopressin and oxytocin receptors, on the SCC across Hyla japonica skin. (1) Both AVT (100 pmol/L or more) and MT (1 nmol/L or more) increased the SCC. (2) The AVT- and MT-induced increases in SCC recovered with time (downregulation). (3) These AVT/MT-induced effects were blocked by application of OPC-31260 (vasopressin V(2)-receptor antagonist). (4) The OPC-31260 concentration needed to block the AVT-induced response was lower upon post-application (after application of agonist) than upon pre-application (before application of agonist), suggesting the number of receptors may have decreased after AVT application. (5) Upon repeated application of AVT (100 pmol/L), the induced SCC increase did not differ significantly between the 1st and 2nd applications. (6) The time to reach the half-maximum value of the AVT-induced or MT-induced increase in SCC was not significantly different between washout and post-application of OPC-31260, suggesting that post-application of OPC-31260 cleared AVT and MT from their receptors. The effects of AVT, MT, and their antagonists in H. japonica, which is adapted to a terrestrial habitat, are compared with our previously published data on Rana catesbeiana (=Lithobates catesbeianus), which is adapted to a semiaquatic habitat.

Developing a solar panel testing system

Directory of Open Access Journals (Sweden)

Árpád Rácz

2009-10-01

Full Text Available Solar energy is increasingly used togenerate electricity for individual households. There isa wide variety of solar panel technologies, whichshould be tested at an individual level during theirlifetime. In this paper, the development of a testingstation at the University of Debrecen is presented. Thetesting system can be used for research andeducational purposes and for in field applicationsequally well.

Investigation on Wall Panel Sandwiched With Lightweight Concrete

Science.gov (United States)

Lakshmikandhan, K. N.; Harshavardhan, B. S.; Prabakar, J.; Saibabu, S.

2017-08-01

The rapid population growth and urbanization have made a massive demand for the shelter and construction materials. Masonry walls are the major component in the housing sector and it has brittle characteristics and exhibit poor performance against the uncertain loads. Further, the structure requires heavier sections for carrying the dead weight of masonry walls. The present investigations are carried out to develop a simple, lightweight and cost effective technology for replacing the existing wall systems. The lightweight concrete is developed for the construction of sandwich wall panel. The EPS (Expanded Polystyrene) beads of 3 mm diameter size are mixed with concrete and developed a lightweight concrete with a density 9 kN/m3. The lightweight sandwich panel is cast with a lightweight concrete inner core and ferrocement outer skins. This lightweight wall panel is tested for in-plane compression loading. A nonlinear finite element analysis with damaged plasticity model is carried out with both material and geometrical nonlinearities. The experimental and analytical results were compared. The finite element study predicted the ultimate load carrying capacity of the sandwich panel with reasonable accuracy. The present study showed that the lightweight concrete is well suitable for the lightweight sandwich wall panels.

Panel and planar experimental shear behavior of wood panels ...

African Journals Online (AJOL)

Panel shear strength along the thickness and planar shear along the length of wood panels laminated softwood oriented OSB 10 mm thick, conditioned at different moisture contents (anhydrous medium, ambient temperature and humid medium) was measured on standardized test specimens, cut in half lengthwise panel ...

Plasma Facing Components Generic Facilities Review Panel (PFC-GFRP): Final report

International Nuclear Information System (INIS)

McGrath, R.; Allen, S.; Hill, D.; Brooks, J.; Mattas, R.; Davis, J.; Lipschultz, B.; Ulrickson, M.

1993-10-01

The Plasma Facing Components (PFC) Facilities Review Panel was chartered by the US Department of Energy, Office of Fusion Energy, ITER (International Thermonuclear Experimental Reactor) and Technology Division, to outline the program plan and identify the supporting test facilities that lead to reliable, long-lived plasma facing components for ITER. This report summarizes the panel's findings and identifies the necessary and sufficient set of test facilities required for ITER PFC development

Optimum design of composite panel with photovoltaic-thermo module. Absorbing effect of cooling panel; Hikari netsu fukugo panel no saiteki sekkei. Reikyaku panel no kyunetsu koka

Energy Technology Data Exchange (ETDEWEB)

Sato, M; Kikuchi, S; Tani, T [Science University of Tokyo, Tokyo (Japan); Kadotani, K; Imaizumi, H [Komatsu Ltd., Tokyo (Japan)

1996-10-27

The composite panel with photovoltaic-thermo module becomes higher in energy-saving than the conventional air-conditioning system by the independent radiational heating and cooling effect obtained when the generating panel using a solar cell module is combined with the heating and cooling panel using a thermo-element module. The output of a solar cell module can be directly used because the solar cell module operates in AC. This paper reports the relation between the absorbed value and power consumption of the cooling panel, while paying attention to the cooling panel. The performance coefficient of the maximum absorbed value from an non-absorbing substance to a cooling panel is 2 to 3. Assume that the cooling panel during non-adiabatic operation is operated using a solar cell module of 800 W/m{sup 2} in solar intensity and 15% in conversion efficiency. The cooling-surface temperature difference is 12.12 K, and the maximum absorbed value of a non-absorbing substance to a cooling panel is 39.12 W/m{sup 2}. The absorbed value of the outer temperature to the cooling panel is 74.4 W/m{sup 2}, and each performance coefficient is 3.26 and 0.62. The absorbed value must be calculated for evaluation from the cooling-surface temperature difference measured directly from the cooling panel. 4 refs., 8 figs., 1 tab.

Arginine Vasotocin, the Social Neuropeptide of Amphibians and Reptiles.

Science.gov (United States)

Wilczynski, Walter; Quispe, Maricel; Muñoz, Matías I; Penna, Mario

2017-01-01

Arginine vasotocin (AVT) is the non-mammalian homolog of arginine vasopressin (AVP) and, like vasopressin, serves as an important modulator of social behavior in addition to its peripheral functions related to osmoregulation, reproductive physiology, and stress hormone release. In amphibians and reptiles, the neuroanatomical organization of brain AVT cells and fibers broadly resembles that seen in mammals and other taxa. Both parvocellular and magnocellular AVT-containing neurons are present in multiple populations located mainly in the basal forebrain from the accumbens-amygdala area to the preoptic area and hypothalamus, from which originate widespread fiber connections spanning the brain with a particularly heavy innervation of areas associated with social behavior and decision-making. As for mammalian AVP, AVT is present in greater amounts in males in many brain areas, and its presence varies seasonally, with hormonal state, and in males with differing social status. AVT's social influence is also conserved across herpetological taxa, with significant effects on social signaling and aggression, and, based on the very small number of studies investigating more complex social behaviors in amphibians and reptiles, AVT may also modulate parental care and social bonding when it is present in these vertebrates. Within this conserved pattern, however, both AVT anatomy and social behavior effects vary significantly across species. Accounting for this diversity represents a challenge to understanding the mechanisms by which AVT exerts its behavioral effects, as well are a potential tool for discerning the structure-function relationships underlying AVT's many effects on behavior.

Aerospace Safety Advisory Panel

Science.gov (United States)

1999-01-01

This report covers the activities of the Aerospace Safety Advisory Panel (ASAP) for calendar year 1998-a year of sharp contrasts and significant successes at NASA. The year opened with the announcement of large workforce cutbacks. The slip in the schedule for launching the International Space Station (ISS) created a five-month hiatus in Space Shuttle launches. This slack period ended with the successful and highly publicized launch of the STS-95 mission. As the year closed, ISS assembly began with the successful orbiting and joining of the Functional Cargo Block (FGB), Zarya, from Russia and the Unity Node from the United States. Throughout the year, the Panel maintained its scrutiny of NASA's safety processes. Of particular interest were the potential effects on safety of workforce reductions and the continued transition of functions to the Space Flight Operations Contractor. Attention was also given to the risk management plans of the Aero-Space Technology programs, including the X-33, X-34, and X-38. Overall, the Panel concluded that safety is well served for the present. The picture is not as clear for the future. Cutbacks have limited the depth of talent available. In many cases, technical specialties are 'one deep.' The extended hiring freeze has resulted in an older workforce that will inevitably suffer significant departures from retirements in the near future. The resulting 'brain drain' could represent a future safety risk unless appropriate succession planning is started expeditiously. This and other topics are covered in the section addressing workforce. The major NASA programs are also limited in their ability to plan property for the future. This is of particular concern for the Space Shuttle and ISS because these programs are scheduled to operate well into the next century. In the case of the Space Shuttle, beneficial and mandatory safety and operational upgrades are being delayed because of a lack of sufficient present funding. Likewise, the ISS has

Development of a Two-Dimensional Tracker with Plasma Panel Detector

CERN Document Server

AUTHOR|(CDS)2233132

Plasma panel sensors are micropattern gaseous radiation detectors which are based on the technology of plasma display panels. This thesis summarizes the research that had been done on commercially available plasma display panels that were converted to plasma panel sensor prototypes and describes the construction of a two-dimensional tracker consisting of four of those prototypes, with one-dimensional readout on each, used to detect tracks of cosmic muons. A large amount of 2-point as well as 3 and 4-point tracks were detected. Qualitative analyses as well as Pearson’s χ2 tests are performed on the track angular distribution and on a histogram of the linearity measure of 3-point tracks to reject the hypothesis that these tracks result from completely random panel hits. Some RF noise effects contributing to false positives are ruled out, while it is shown that other effects can be ruled out only with a high-intensity minimum ionizing particle source. A significant part of the tracker construction was the dev...

Next-Generation NATO Reference Mobility Model (NRMM) Development (Developpement de la nouvella generation du modele de mobilite de reference de l’OTAN (NRMM))

Science.gov (United States)

2018-01-01

There is little by way of success stories to build upon on this front, though deep learning and other machine learning technologies are highly...NORTH ATLANTIC TREATY ORGANIZATION SCIENCE AND TECHNOLOGY ORGANIZATION AC/323(AVT-ET-148)TP/728 www.sto.nato.int STO EXPLORATORY...Distribution and Availability on Back Cover NORTH ATLANTIC TREATY ORGANIZATION SCIENCE AND TECHNOLOGY ORGANIZATION AC/323

The Management of Information & Knowledge; Meeting of the Panel on Science and Technology with the Committee on Science and Astronautics, U.S. House of Representatives.

Science.gov (United States)

Congress of the U.S., Washington, DC. House Committee on Science and Technology.

The emphasis of the eleventh meeting of the Panel on Science and Technology was on the management of information and knowledge. It was organized essentially as a seminar with two papers given at each session. The topic of the first two papers presented was: "Computers, Communications, and the Economy." The papers given at the second session were…

Laser illuminated flat panel display

Energy Technology Data Exchange (ETDEWEB)

Veligdan, J.T.

1995-12-31

A 10 inch laser illuminated flat panel Planar Optic Display (POD) screen has been constructed and tested. This POD screen technology is an entirely new concept in display technology. Although the initial display is flat and made of glass, this technology lends itself to applications where a plastic display might be wrapped around the viewer. The display screen is comprised of hundreds of planar optical waveguides where each glass waveguide represents a vertical line of resolution. A black cladding layer, having a lower index of refraction, is placed between each waveguide layer. Since the cladding makes the screen surface black, the contrast is high. The prototype display is 9 inches wide by 5 inches high and approximately I inch thick. A 3 milliwatt HeNe laser is used as the illumination source and a vector scanning technique is employed.

Temperature Dependences on Various Types of Photovoltaic (PV) Panel

International Nuclear Information System (INIS)

Audwinto, I A; Leong, C S; Sopian, K; Zaidi, S H

2015-01-01

Temperature is one of the key roles in PV technology performance, since with the increases of temperature the open-circuit voltage will drop accordingly so do the electrical efficiency and power output generation. Different types of Photovoltaic (PV) panels- silicon solar panels and thin film solar panels; mono-crystalline, poly-crystalline, CIS, CIGS, CdTe, back-contact, and bi-facial solar panel under 40°C to 70°C approximately with 5°C interval have been comparatively analyzed their actual performances with uniformly distribution of light illumination from tungsten halogen light source, ±500W/m 2 . DC-Electronic Load and Data Logger devices with “Lab View” data program interface were used to collect all the necessary parameters in this study. Time needed to achieve a certain degree of temperature was recorded. Generally, each of the panels needed 15 minutes to 20 minutes to reach 70°C. Halogen based light source is not compatible in short wave-length in response to thin-film solar cell. Within this period of times, all the panels are facing a performance loss up to 15%. Other parameters; P max , V max , I max , V oc , I sc , R serries , R shunt , Fillfactor were collected as study cases. Our study is important in determining Photovoltaic type selection and system design as for study or industrial needed under different temperature condition. (paper)

Digital radiography with large-area flat-panel detectors

International Nuclear Information System (INIS)

Kotter, E.; Langer, M.

2002-01-01

Large-area flat-panel detectors with active readout mechanisms have been on the market for the past 2 years. This article describes different detector technologies. An important distinction is made between detectors with direct and those with indirect conversion of X-rays into electrical charges. Detectors with indirect conversion are built with unstructured or structured scintillators, the latter resulting in less lateral diffusion of emitted light. Some important qualities of flat-panel detectors are discussed. The first phantom and clinical studies published report an image quality at least comparable to that of screen-film systems and a potential for dose reduction. The available studies are summarised in this article. (orig.)

Plasma Panel Detectors for MIP Detection for the SLHC and a Test Chamber Design

CERN Document Server

Ball, Robert; Etzion, Erez; Friedman, Peter S; Levin, Daniel S; Moshe, Meny Ben; Weaverdyck, Curtis; Zhou, Bing

2010-01-01

Performance demands for high and super-high luminosity at the LHC (up to 10^35 cm^(-2) sec^(-1) after the 2017 shutdown) and at future colliders demand high resolution tracking detectors with very fast time response and excellent temporal and spatial resolution. We are investigating a new radiation detector technology based on Plasma Display Panels (PDP), the underlying engine of panel plasma television displays. The design and production of PDPs is supported by four decades of industrial development. Emerging from this television technology is the Plasma Panel Sensor (PPS), a novel variant of the micropattern radiation detector. The PPS is fundamentally an array of micro-Geiger plasma discharge cells operating in a non-ageing, hermetically sealed gas mixture . We report on the PPS development program, including design of a PPS Test Cell.

Effects of arginine vasotocin and mesotocin on the activation and development of amiloride-blockable short-circuit current across larval, adult, and cultured larval bullfrog skins.

Science.gov (United States)

Takada, Makoto; Fujimaki-Aoba, Kayo; Hokari, Shigeru

2010-03-01

Amphibian skin has osmoregulatory functions, with Na(+) crossing from outside to inside. Na(+) transport can be measured as the short-circuit current (SCC). We investigated the short-term and long-term effects of arginine vasotocin (AVT) and mesotocin (MT) (which modulate Na(+) transport) on the activation and development of an amiloride-blockable SCC (adult-type feature) in larval, adult, and corticoid-cultured larval bullfrog skins. We found: (1) AVT-receptor (AVT-R) and MT-receptor (MT-R) mRNAs could be detected in both larval and adult skins, (2) in the short term (within 60 min), the larval SCC (amiloride-stimulated SCC) was increased by AVT, forskolin, and MT, suggesting that AVT and MT did not activate the inactive ENaC (epithelial sodium channel) protein thought to be expressed in larval skin, (3) in the short term (within 90 min), AVT, forskolin, and MT stimulated the adult SCC (amiloride-blockable SCC), (4) AVT and MT increased both the larval and adult SCC via receptors insensitive to OPC-21268 (an antagonist of the V(1)-type receptor), OPC-31260 (an antagonist of the V(2)-type receptor), and ([d(CH(2))(5),Tyr(Me)(2),Thr(4),Orn(8),des-Gly-NH (2) (9) ]VT) (an antagonist of the oxytocin receptor), (5) culturing EDTA-treated larval skin with corticoids supplemented with AVT (1 microM) or MT (1 microM) for 2 weeks (long-term effects of AVT and MT) did not alter the corticoid-induced development of an amiloride-blockable SCC (adult-type feature). AVT and MT thus have the potential to stimulate SCC though channels that are already expressed, but they may not influence the development of the amiloride-blockable SCC (an adult-type feature) in larval skin.

Stress Testing of Organic Light- Emitting Diode Panels and Luminaires

Energy Technology Data Exchange (ETDEWEB)

Lynn Davis, Kelley Rountree, Karmann Mills

2018-01-31

This report builds on previous DOE efforts with OLED technology by updating information on a previously benchmarked OLED product (the Chalina luminaire from Acuity Brands) and provides new benchmarks on the performance of Brite 2 and Brite Amber OLED panels from OLEDWorks. During the tests described here, samples of these devices were subjected to continuous operation in stress tests at elevated ambient temperature environments of 35°C or 45°C. In addition, samples were also operated continuously at room temperature in a room temperature operational life test (RTOL). One goal of this study was to investigate whether these test conditions can accelerate failure of OLED panels, either through panel shorting or an open circuit in the panel. These stress tests are shown to provide meaningful acceleration of OLED failure modes, and an acceleration factor of 2.6 was calculated at 45°C for some test conditions. In addition, changes in the photometric properties of the emitted light (e.g., luminous flux and chromaticity maintenance) was also evaluated for insights into the long-term stability of these products compared to earlier generations. Because OLEDs are a lighting system, electrical testing was also performed on the panel-driver pairs to provide insights into the impact of the driver on long-term panel performance.

Do I put Solar Panels on My Roof If My Neighbors Can See Them?

DEFF Research Database (Denmark)

Ørding Olsen, Anders; Claussen, Jörg; Tumlinson, Justin

if they want to conform to their peers. We study in how far the potential visibility of solar panels from the street influences the adoption decision of 122,349 Danish households and find that conformity motivations seem to dominate, i.e. the average household is less likely to adopt if solar panels...... are visible from the street, but less wealthy households are more likely to adopt of solar panels are visible. These findings generate policy implications for supporting the adoption of sustainable technologies....

Cleaning Robot for Solar Panels in Solar Power Station

Science.gov (United States)

Hang, Lu-Bin; Shen, Cheng-Wei; Bian, Huai-Qiang; Wang, Yan

2016-05-01

The dust particles on solar panel surface have been a serious problem for the photovoltaic industry, a new monorail-tracked robot used for automatic cleaning of solar panel is presented in this paper. To meet the requirement of comprehensive and stable cleaning of PV array, the monorail-tracked pattern of robot is introduced based on the monorail structure technique. The running and striding mechanism are designed for mobility of robot on the solar panels. According to the carrying capacity and water circulation mechanism, a type of self-cleaning device with filtering system is developed. Combined with the computer software and communications technology, the control system is built in this robot, which can realize the functions of autonomous operation, positioning and monitoring. The application of this developed cleaning robot can actualize the Industrialization of automatic cleaning for PV components and have wide market prospect.

Phase Change Material Based Accumulation Panels in Combination with Renewable Energy Sources and Thermoelectric Cooling

Directory of Open Access Journals (Sweden)

Jan Skovajsa

2017-01-01

Full Text Available The article deals with the use of modern materials and technologies that can improve the thermal comfort in buildings. The article describes the design and usage of a special accumulation device, which is composed of thermal panels based on phase change materials (PCMs. The thermal panels have an integrated tube heat exchanger and heating foils. The technology can be used as a passive or active system for heating and cooling. It is designed as a “green technology”, so it is able to use renewable energy sources, e.g., photovoltaic (PV panels, solar thermal collectors and heat pumps. Moreover, an interesting possibility is the ability to use thermoelectric coolers. In the research, measurements of the different operating modes were made, and the results are presented in the text. The measurement approves that the technology improves the thermal capacity of the building, and it is possible to use it for active heating and cooling.

77 FR 68784 - Prospective Grant of Exclusive License: Multiple-Valent Opsonophagocytic Assay Selection Panel...

Science.gov (United States)

2012-11-16

... Licensing and Marketing Specialist, Technology Transfer Office, Centers for Disease Control and Prevention... Technology Transfer Office, Centers for Disease Control and Prevention (CDC), Department of Health and Human... Opsonophagocytic Assay Selection Panel Arrays and Uses Therefor'', issued 1/5/2010. CDC Technology ID No. I-035-04...

WTEC panel report on European nuclear instrumentation and controls. Final report

Energy Technology Data Exchange (ETDEWEB)

White, J.D.; Lanning, D.D.; Johnson, P.M.H. [eds.] [World Technology Evaluation Center, Baltimore, MD (United States); Shelton, R.D. [World Technology Evaluation Center, Baltimore, MD (United States)

1991-12-01

A study of instrumentation and controls (I and C) technology used in nuclear power plants in Europe was conducted by a panel of US specialists. This study plants in Europe was conducted by a panel of US specialists. This study included a review of the literature on the subject, followed by a visit to some of the leading organizations in Europe in the field nuclear I and C. Areas covered are: (1) role of the operator and control room design; (2) transition from analog to digital technology; (3) computerized operator support systems for fault management; (4) control strategies and techniques; (5) Nuclear power plant I and C architecture; (6) instrumentation and (7) computer standards and tools. The finding relate to poor reactions.

Comprehensive metabolic panel

Science.gov (United States)

Metabolic panel - comprehensive; Chem-20; SMA20; Sequential multi-channel analysis with computer-20; SMAC20; Metabolic panel 20 ... Chernecky CC, Berger BJ. Comprehensive metabolic panel (CMP) - blood. In: ... Tests and Diagnostic Procedures . 6th ed. St Louis, MO: ...

Noise Reduction in Double‿Panel Structures by Cavity and Panel Resonance Control

NARCIS (Netherlands)

Ho, J.; Berkhoff, Arthur P.

2011-01-01

This paper presents an investigation of the cavity and the panel resonance control in a double‿panel structure. The double‿panel structure, which consists of two panels with air in the gap, is widely adopted in many applications such as aerospace due to its light weight and effective

Noise reduction in double-panel structures by cavity and panel resonance control

NARCIS (Netherlands)

Ho, J.-H.; Berkhoff, A.P

2011-01-01

This paper presents an investigation of the cavity and the panel resonance control in a double‐panel structure. The double‐panel structure, which consists of two panels with air in the gap, is widely adopted in many applications such as aerospace due to its light weight and effective

Characterization of vacuolar amino acid transporter from Fusarium oxysporum in Saccharomyces cerevisiae.

Science.gov (United States)

Lunprom, Siriporn; Pongcharoen, Pongsanat; Sekito, Takayuki; Kawano-Kawada, Miyuki; Kakinuma, Yoshimi; Akiyama, Koichi

2015-01-01

Fusarium oxysporum causes wilt disease in many plant families, and many genes are involved in its development or growth in host plants. A recent study revealed that vacuolar amino acid transporters play an important role in spore formation in Schizosaccharomyces pombe and Saccharomyces cerevisiae. To investigate the role of vacuolar amino acid transporters of this phytopathogenic fungus, the FOXG_11334 (FoAVT3) gene from F. oxysporum was isolated and its function was characterized. Transcription of FoAVT3 was upregulated after rapamycin treatment. A green fluorescent protein fusion of FoAvt3p was localized to vacuolar membranes in both S. cerevisiae and F. oxysporum. Analysis of the amino acid content of the vacuolar fraction and amino acid transport activities using vacuolar membrane vesicles from S. cerevisiae cells heterologously expressing FoAVT3 revealed that FoAvt3p functions as a vacuolar amino acid transporter, exporting neutral amino acids. We conclude that the FoAVT3 gene encodes a vacuolar neutral amino acid transporter.

Moderately reverberant learning ultrasonic pinch panel.

Science.gov (United States)

Nikolovski, Jean-Pierre

2013-10-01

Tactile sensing is widely used in human-computer interfaces. However, mechanical integration of touch technologies is often perceived as difficult by engineers because it often limits the freedom of style or form factor requested by designers. Recent work in active ultrasonic touch technologies has made it possible to transform thin glass plates, metallic sheets, or plastic shells into interactive surfaces. The method is based on a learning process of touch-induced, amplitude-disturbed diffraction patterns. This paper proposes, first, an evolution in the design with multiple dipole transducers that improves touch sensitivity or maximum panel size by a factor of ten, and improves robustness and usability in moderately reverberant panels, and second, defines a set of acoustic variables in the signal processing for the evaluation of sensitivity and radiating features. For proof of concept purposes, the design and process are applied to 3.2- and 6-mm-thick glass plates with variable damping conditions. Transducers are bonded to only one short side of the rectangular substrates. Measurements show that the highly sensitive free lateral sides are perfectly adapted for pinch-touch and pinch-slide interactions. The advantage of relative versus absolute touch disturbance measurement is discussed, together with tolerance to abutting contaminants.

Honeycomb technology materials, design, manufacturing, applications and testing

CERN Document Server

Bitzer, Tom

1997-01-01

Honeycomb Technology is a guide to honeycomb cores and honeycomb sandwich panels, from the manufacturing methods by which they are produced, to the different types of design, applications for usage and methods of testing the materials. It explains the different types of honeycomb cores available and provides tabulated data of their properties. The author has been involved in the testing and design of honeycomb cores and sandwich panels for nearly 30 years. Honeycomb Technology reflects this by emphasizing a `hands-on' approach and discusses procedures for designing sandwich panels, explaining the necessary equations. Also included is a section on how to design honeycomb energy absorbers and one full chapter discussing honeycomb core and sandwich panel testing. Honeycomb Technology will be of interest to engineers in the aircraft, aerospace and building industries. It will also be of great use to engineering students interested in basic sandwich panel design.

PERBANDINGAN UNJUK KERJA ANTARA PANEL SEL SURYA BERPENJEJAK DENGAN PANEL SEL SURYA DIAM

Directory of Open Access Journals (Sweden)

Syafaruddin Ch

2010-07-01

Full Text Available The ability to produce electrical energy at Solar Power Plant  is highly dependent on the magnitude and duration of sun exposure on the solar cell panels. The movement of the sun from east to west that periodicity in every day is a problem at  the  optimization generation of electricity at  Solar Power Plant   if using solar panel that motionless. This is because the solar cell panel can not catch the maximum sun exposure. To solve the above problem then designed a solar cell panel  tracker  capable of follo-wing the movements of the sun. Then conducted a test to see the performance of solar cell pa-nel  tracker  and compare it with the performance of solar cell panel was motionless. The testing doing along 6 days, with way to irradiate the panel of solar cells  tracker  and panels of solar cell motionless with sun exposure  along a  full day. Then the electric current generated each panel were recorded. The comparison of current then generating comparison of electric power delivery. The result show that the solar cell panel  tracker  produce the average current is 2.19 A whereas solar-cell panel still 1.97 A.  This result   indicate that average power for solar cell panel  tracker  39.41 W while for solar cell panel that motionless is  35.46 W. These results indicate that the performance of solar cell panel  tracker  better than  solar cell panel motionless.

Noise Reduction in Double‿Panel Structures by Cavity and Panel Resonance Control

OpenAIRE

Ho, J.; Berkhoff, Arthur P.

2011-01-01

This paper presents an investigation of the cavity and the panel resonance control in a double‿panel structure. The double‿panel structure, which consists of two panels with air in the gap, is widely adopted in many applications such as aerospace due to its light weight and effective transmission‿loss at high frequency. However, the resonance of the cavity and the poor transmission‿loss at low frequency limit its noise control performance. Applying active control forces on the panels or utili...

Integrated Thermal Treatment Systems study: US Department of Energy Internal Review Panel report

International Nuclear Information System (INIS)

Cudahy, J.; Escarda, T.; Gimpel, R.

1995-04-01

The U.S. Department of Energy's (DOE) Office of Technology Development (OTD) commissioned two studies to uniformly evaluate nineteen thermal treatment technologies. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the advice and guidance of the DOE Office of Environmental Management's (EM's) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel, composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency (EPA), the California EPA, and private experts. The Panel met from November 15-18, 1994, to review and comment on the ITTS studies, to make recommendations on the most promising thermal treatment systems for DOE mixed low level wastes (MLLW), and to make recommendations on research and development necessary to prove the performance of the technologies on MLLW

Sustainability challenges of residential reinforced - concrete panel buildings

Directory of Open Access Journals (Sweden)

Markku J. Riihimäki

2014-06-01

Full Text Available Quite similar large-panel prefabrication technologies were used for residential buildings in East-Europe and some countries in Northern-Europe, e.g. Finland. Even if technologically similar, the fate of the building stocks is different in the two regions, with buildings functioning sustainably in Finland. Hence, one could adapt the maintenance and renovation experiences to the building stock in other countries, creating opportunities for communities and business. The paper presents technological, economical, and institutional/policy aspects in the two environments, and discusses them in the larger framework of European sustainability targets. For major renovation, as targeted in the paper, methods of change management should be applied, entailing thoughtful planning and sensitive implementation and above all, consultation/involvement of the people affected. If the presented interventions would be used in a systematic and planned way, improvements can be achieved for social sustainability targets like e.g. adaptability and visual comfort, while maintaining the safety and security. Finally, the limitations of the approach in light of the institutional setting and ownership structure are discussed, highlighting how different ownership models are favoring or hindering major retrofit interventions. The paper offers ways on strengthening the role of key stakeholders to support major renovation interventions on the panel building stock.

Development of Ad Valorem Real Property Taxation System in Moldova

Directory of Open Access Journals (Sweden)

Olga Buzu

2014-12-01

Full Text Available The author analyzes key aspects of the new ad valorem property taxation (AVT system which is currently implemented in the Republic of Moldova and outlines ways of its further potential development. The author uses both systemic and synergistic approaches to develop a methodology for the assessment of the AVT system efficiency based on the multipurpose cadastre data. The study identifies key characteristics of the AVT system, as well as main problems associated with the implementation of the new property taxation system and with the compatibility of the fiscal and the real property cadastre data, and makes suggestions for further development of the AVT system in the country. The study allows to identify and maximize the benefits of the AVT system.

Technical trends of large-size photomasks for flat panel displays

Science.gov (United States)

Yoshida, Koichiro

2017-06-01

Currently, flat panel displays (FPDs) are one of the main parts for information technology devices and sets. From 1990's to 2000's, liquid crystal displays (LCDs) and plasma displays had been mainstream FPDs. In the middle of 2000's, demand of plasma displays declined and organic light emitting diodes (OLEDs) newly came into FPD market. And today, major technology of FPDs are LCDs and OLEDs. Especially for mobile devices, the penetration of OLEDs is remarkable. In FPDs panel production, photolithography is the key technology as same as LSI. Photomasks for FPDs are used not only as original master of circuit pattern, but also as a tool to form other functional structures of FPDs. Photomasks for FPDs are called as "Large Size Photomasks(LSPMs)", since the remarkable feature is " Size" which reaches over 1- meter square and over 100kg. In this report, we discuss three LSPMs technical topics with FPDs technical transition and trend. The first topics is upsizing of LSPMs, the second is the challenge for higher resolution patterning, and the last is "Multi-Tone Mask" for "Half -Tone Exposure".

A targeted resequencing gene panel for focal epilepsy.

Science.gov (United States)

Hildebrand, Michael S; Myers, Candace T; Carvill, Gemma L; Regan, Brigid M; Damiano, John A; Mullen, Saul A; Newton, Mark R; Nair, Umesh; Gazina, Elena V; Milligan, Carol J; Reid, Christopher A; Petrou, Steven; Scheffer, Ingrid E; Berkovic, Samuel F; Mefford, Heather C

2016-04-26

We report development of a targeted resequencing gene panel for focal epilepsy, the most prevalent phenotypic group of the epilepsies. The targeted resequencing gene panel was designed using molecular inversion probe (MIP) capture technology and sequenced using massively parallel Illumina sequencing. We demonstrated proof of principle that mutations can be detected in 4 previously genotyped focal epilepsy cases. We searched for both germline and somatic mutations in 251 patients with unsolved sporadic or familial focal epilepsy and identified 11 novel or very rare missense variants in 5 different genes: CHRNA4, GRIN2B, KCNT1, PCDH19, and SCN1A. Of these, 2 were predicted to be pathogenic or likely pathogenic, explaining ∼0.8% of the cohort, and 8 were of uncertain significance based on available data. We have developed and validated a targeted resequencing panel for focal epilepsies, the most important clinical class of epilepsies, accounting for about 60% of all cases. Our application of MIP technology is an innovative approach that will be advantageous in the clinical setting because it is highly sensitive, efficient, and cost-effective for screening large patient cohorts. Our findings indicate that mutations in known genes likely explain only a small proportion of focal epilepsy cases. This is not surprising given the established clinical and genetic heterogeneity of these disorders and underscores the importance of further gene discovery studies in this complex syndrome. © 2016 American Academy of Neurology.

Economical evaluation of damaged vacuum insulation panels in buildings

Science.gov (United States)

Kim, Y. M.; Lee, H. Y.; Choi, G. S.; Kang, J. S.

2015-12-01

In Korea, thermal insulation standard of buildings have been tightened annually to satisfy the passive house standard from the year 2009. The current domestic policies about disseminating green buildings are progressively conducted. All buildings should be the zero energy building in the year 2025, obligatorily. The method is applied to one of the key technologies for high-performance insulation for zero energy building. The vacuum insulation panel is an excellent high performance insulation. But thermal performance of damaged vacuum insulation panels is reduced significantly. In this paper, the thermal performance of damaged vacuum insulation panels was compared and analyzed. The measurement result of thermal performance depends on the core material type. The insulation of building envelope is usually selected by economic feasibility. To evaluate the economic feasibility of VIPs, the operation cost was analyzed by simulation according to the types and damaged ratio of VIPs

Pain and Joy of a Panel Survey on Transport Studies

Energy Technology Data Exchange (ETDEWEB)

Comendador Arquero, María Eugenia López-Lambas

2016-07-01

Over ten years ago, it was established that the most frequent reason that motivates a panel survey on transport studies is the evaluation of a change in the transportation system, or a specific transportation-planning project, especially when the project involves novel elements. From a statistical viewpoint, a panel survey has the definite advantage to offer more accurate estimatesof changes than cross-sectional surveys for the same sample size. Observing travel patterns of individuals and households overseveral consecutive days, has offered insights into activity scheduling and travel planning. Variability in travel patterns has important policy implications as well, but how much effort is worth to design a panel survey? To evaluate the effects of the transport policies introduced in Madrid during the last five years, a ‘short-long’ panel survey wasbuilt, based on a sample of a Madrid-worker subpopulation most affected by those recent changes in transport policy. The paper describes both the design and construction of the panel based on GPS technology, and presents some results based on an analysis of its two waves; for example, it registered an increment of public transport use and walking trips in 10%. The panel overcomes the known attrition problem thanks to providing incentives, maintaining contact, using the same interviewer for the same respondents, and conducting face-to-face interviews. (Author)

Panel 5: Microbiology and Immunology Panel

Science.gov (United States)

Murphy, Timothy F.; Chonmaitree, Tasnee; Barenkamp, Stephen; Kyd, Jennelle; Nokso-Koivisto, Johanna; Patel, Janak A.; Heikkinen, Terho; Yamanaka, Noboru; Ogra, Pearay; Swords, W. Edward; Sih, Tania; Pettigrew, Melinda M.

2014-01-01

Objective The objective is to perform a comprehensive review of the literature from January 2007 through June 2011 on the virology, bacteriology, and immunology related to otitis media. Data Sources PubMed database of the National Library of Medicine. Review Methods Three subpanels with co-chairs comprising experts in the virology, bacteriology, and immunology of otitis media were formed. Each of the panels reviewed the literature in their respective fields and wrote draft reviews. The reviews were shared with all panel members, and a second draft was created. The entire panel met at the 10th International Symposium on Recent Advances in Otitis Media in June 2011 and discussed the review and refined the content further. A final draft was created, circulated, and approved by the panel. Conclusion Excellent progress has been made in the past 4 years in advancing an understanding of the microbiology and immunology of otitis media. Advances include laboratory-based basic studies, cell-based assays, work in animal models, and clinical studies. Implications for Practice The advances of the past 4 years formed the basis of a series of short-term and long-term research goals in an effort to guide the field. Accomplishing these goals will provide opportunities for the development of novel interventions, including new ways to better treat and prevent otitis media. PMID:23536533

A technology developed at CERN captures the sun's energy

CERN Multimedia

Alizée Dauvergne

2010-01-01

A civil-engineering company has recently started using thermal solar panels based on ultra-high vacuum technology developed at CERN. By efficiently preventing heat loss, the technology allows water to be heated to several hundred degrees, even in a temperate climate.   The field of solar panels using technology developed at CERN. On Tuesday 15 June the Geneva branch of the civil-engineering company Colas opened a new solar power plant based on ultra-high vacuum technology developed at CERN. Measuring a total of 80 square metres, the environmentally friendly "solar field" heats close to 80,000 litres of bitumen to 180 degrees. "To be able to reach such a high temperature, I drew on the ultra-high vacuum technologies I learned about at CERN", explains Cristoforo Benvenuti, who invented the panels. The ultra-high vacuum is what makes these solar panels so innovative. "It's very attractive because it minimises heat loss", continues Benvenuti. &...

2015 Advanced Environmental Health/Advanced Food Technology Standing Review Panel

Science.gov (United States)

Steinberg, Susan

2015-01-01

The 2015 Advanced Environmental Health/Advanced Food Technology (AEH/AFT) Standing Review Panel (from here on referred to as the SRP) met for a site visit in Houston, TX on December 14 - 15, 2015. The SRP met with representatives from the Space Human Factors and Habitability (SHFH) Element and members of the Human Research Program (HRP) to review the updated research plans for the Risk of Adverse Health Effects Due to Host-Microorganism Interactions (MicroHost Risk) and the Risk of Performance Decrement and Crew Illness due to an Inadequate Food System (Food Risk). During the meeting, the SRP also met with the vehicle engineers to discuss possible food storage options. The SRP would like to commend Dr. Oubre and Dr. Douglas for their detailed presentations, as well the frank, refreshing, and comprehensive engineering presentation. This gave much needed perspective to the food storage issues and reassured the committee about NASA's approach to the problem. In terms of critiques, the SRP remains unconvinced about the rationale for probiotic use other than for specific applications supported by the literature. It is not clear what gap or problem is being addressed by the use of probiotics, and the rationale for their use needs to be clearly rooted in the available literature. The SRP thinks that if low-Earth orbit is associated with immune system impairment, then there may additional risks linked with the use of probiotics. It is not clear to the SRP how NASA will determine if probiotics are having their intended beneficial effect. A similar concern is raised as to what gaps or problems are being addressed by "functional foods". Mixed infections, rather than single species infections, which can augment severity of disease, also represent a significant concern. Overall, the SRP considers this to be a strong program that is well-organized, well-coordinated and generates valuable data.

Structure, Mechanism, and Application of Vacuum Insulation Panels in Chinese Buildings

OpenAIRE

Peng, Changhai; Yang, Jianqiang

2016-01-01

Thermal insulation is one of the most used approaches to reduce energy consumption in buildings. Vacuum insulation panels (VIPs) are new thermal insulation materials that have been used in the domestic and overseas market in the last 20 years. Due to the vacuum thermal insulation technology of these new materials, their thermal conductivity can be as low as 0.004 W/(m·K) at the center of panels. In addition, VIPs that are composites with inorganic core and an envelope out of commonly three me...

Anthropometric Considerations in the Modernized Main Control Room: Application to a Virtual Nuclear Power Plant Control Panel

International Nuclear Information System (INIS)

Yang, Chih Wei; Cheng, Tsung Chieh; Lin, Chiuhsiang Joe

2011-01-01

This study investigates the anthropometric considerations in the main control room (MCR) application to a virtual nuclear power plant (NPP) control panel. Influences of working postures and physical demands on the operational performance are also discussed. Finally, the present research provides a case example to illustrate the influences of anthropometric considerations on the control panel design for MCR operators by applying virtual reality (VR) technology. The MCR design primarily evolved in different countries. The datasets available is usually insufficient or inconsistent for the end users. To solve the upper mentioned problem, this study put emphasis on applying VR technology to anthropometric considerations support control panel design in the modernized MCR. Although the concept of applying VR technology on anthropometric considerations in this paper is related to the MCR in NPPs, it could be easily applied for the purposes of any type of control room in a similar manner

Anthropometric Considerations in the Modernized Main Control Room: Application to a Virtual Nuclear Power Plant Control Panel

Energy Technology Data Exchange (ETDEWEB)

Yang, Chih Wei; Cheng, Tsung Chieh [Institute of Nuclear Energy Research, Taoyuan (China); Lin, Chiuhsiang Joe [Chung-Yuan Christian University, Chung Li (China)

2011-08-15

This study investigates the anthropometric considerations in the main control room (MCR) application to a virtual nuclear power plant (NPP) control panel. Influences of working postures and physical demands on the operational performance are also discussed. Finally, the present research provides a case example to illustrate the influences of anthropometric considerations on the control panel design for MCR operators by applying virtual reality (VR) technology. The MCR design primarily evolved in different countries. The datasets available is usually insufficient or inconsistent for the end users. To solve the upper mentioned problem, this study put emphasis on applying VR technology to anthropometric considerations support control panel design in the modernized MCR. Although the concept of applying VR technology on anthropometric considerations in this paper is related to the MCR in NPPs, it could be easily applied for the purposes of any type of control room in a similar manner.

Comparisons between various cavity and panel noise reduction control in double-panel structures

NARCIS (Netherlands)

Ho, J.H.; Kalverboer, J.; Berkhoff, A.P.

2012-01-01

This paper presents comparisons between various panel and cavity resonance control methods to reduce the transmitted sound in a double-panel structure. The double-panel, which consists of two panels with air in the gap, has the advantages of low weight and effective transmission-loss at high

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

Introduction and Overview of the Industrial Interactive Panel Session

Science.gov (United States)

Seiler, David

2014-03-01

A unique industrial panel covering the challenges and needs of various industries and how being innovative is important. The session involves two invited industry speakers (24 minutes each) who will set the stage for the interactive round table panel session. The Panel, led by moderator Mark Bernius (Morgan Advanced Materials), consists of the two invited speakers plus an additional five industry panelists. The first thirty minutes of the panel session has the five additional panelists introducing themselves and their work/company. These introductions could include what they or their company does, sharing one or two technical highlights, listing some challenges or needs for physicists, and what innovation breakthroughs are needed in their industries. The final hour of the session will be highly interactive with questions to the panel coming from the moderator, the audience, and the panelists themselves. Questions that might be addressed include: how physicists are or could be critical in advancing innovation; how can AIP/APS/FIAP help industry get the physics help they need to be innovative (knowledge, the right staff, etc.); what role can students and post docs play in advancing industry's mission; etc. We invite you to participate in this interactive session and ask our industry experts your own interesting and challenging questions. The invited speakers are George Thompson, Intel, and Rick Watkins, Nike. The panel members also include Jason Cleveland, Asylum Research; Robert Doering, Texas Instruments; William Gallagher, IBM T.J. Watson Research Center; James Hollenhorst, Agilent Technologies; and Martin Poitzsch, Schlumberger-Doll Research.

Facade renovation - replacement and restoration of the panels in a monument protected object

Science.gov (United States)

Novotný, Michal

2017-12-01

The article deals with problems of reconstruction of the facade and the associated problem of replacement or repair of the panels. In conventional buildings it is a smooth operation, but it is problematic in monument-protected objects. In the case of a common building, it is possible to choose any modern panels and simply replace them, but for historical objects we have to follow the claims and the rules of monument protection. In practice, it usually means the impossibility of use of modern panels, but at least a combination of old and modern technologies. Another possible solution to the problem is renovation, or repairs to the original state of the existing panels, of course with respect to the functionality of such panels. The implementation of such repairs must always be based on the technical and historical survey of the condition of the object and the repairs must be professionally designed. Subsequently, corrections are made, during which it is necessary to pay particular attention to observance of the technological procedures, rules and instructions particularly in terms of monument protection. However, the functionality of the works or elements made with regard to the quality of the environment within the building is not negligible. A common problem is the lack of control of technical requirements and functional requirements. Underestimation of the problems then leads to difficult repairs. The article points to the mistakes and problems of one such construction project on a historically protected chateau building.

Lightening Body Armor: Arroyo Support to the Army Response to Section 125 of the National Defense Authorization Act for Fiscal Year 2011

Science.gov (United States)

2012-01-01

Reports & Bookstore Make a charitable contribution Limited Electronic Distribution Rights This document and trademark(s) contained herein are protected by...Biomechanical and Medical Aspects of Soldier Load Carriage,” meeting on Soldier Mobility, Kingston, Canada, NATO Research and Technology Organisation ...Structural Applications, Meeting Proceedings, NATO Research and Technology Organisation , RTO-MP-AVT-122, August 2006. As of June 29, 2011: http

Quantification of Wine Mixtures with an Electronic Nose and a Human Panel

Science.gov (United States)

Aleixandre, Manuel; Cabellos, Juan M.; Arroyo, Teresa; Horrillo, M. C.

2018-01-01

In this work, an electronic nose and a human panel were used for the quantification of wines formed by binary mixtures of four white grape varieties and two varieties of red wines at different percentages (from 0 to 100% in 10% steps for the electronic nose and from 0 to 100% in 25% steps for the human panel). The wines were prepared using the traditional method with commercial yeasts. Both techniques were able to quantify the mixtures tested, but it is important to note that the technology of the electronic nose is faster, simpler, and more objective than the human panel. In addition, better results of quantification were also obtained using the electronic nose. PMID:29484296

Efficient and Reliable Solar Panels for Small CubeSat Picosatellites

Directory of Open Access Journals (Sweden)

Ivo Vertat

2014-01-01

Full Text Available CubeSat picosatellites have a limited area of walls for solar cells assembling and the available area has to be effectively shared with other parts, such as planar antennas, optical sensors, camera lens, and access port. With standard size of solar cell strings, it is not possible to construct a reliable solar panel for CubeSat with redundant strings interconnection. Typical solar panels for CubeSat consist of two solar cell strings serially wired with no redundancy in case of solar string failure. The loss of electric energy from one solar panel can cause a serious problem for most picosatellites due to minimum margin in the blueprints of the picosatellite subsystem power budget. In this paper, we propose a new architecture of solar panels for PilsenCUBE CubeSat with a high level of redundancy in the case of solar string failure or following switched power regulator failure. Our solar panels use a high efficiency triple junction GaInP2/GaAs/Ge in the form of small triangle strings from the Spectrolab Company. A suitable technology for precise solar cell assembling is also discussed, because CubeSat picosatellites are usually developed by small teams with limited access to high-end facilities.

Solar reflection panels

Science.gov (United States)

Diver, Jr., Richard B.; Grossman, James W [Albuquerque, NM; Reshetnik, Michael [Boulder, CO

2006-07-18

A solar collector comprising a glass mirror, and a composite panel, wherein the back of the mirror is affixed to a front surface of the composite panel. The composite panel comprises a front sheet affixed to a surface of a core material, preferably a core material comprising a honeycomb structure, and a back sheet affixed to an opposite surface of the core material. The invention may further comprise a sealing strip, preferably comprising EPDM, positioned between the glass mirror and the front surface of the composite panel. The invention also is of methods of making such solar collectors.

Hypervelocity Impact Performance of Open Cell Foam Core Sandwich Panel Structures

Science.gov (United States)

Ryan, S.; Ordonez, E.; Christiansen, E. L.; Lear, D. M.

2010-01-01

Open cell metallic foam core sandwich panel structures are of interest for application in spacecraft micrometeoroid and orbital debris shields due to their novel form and advantageous structural and thermal performance. Repeated shocking as a result of secondary impacts upon individual foam ligaments during the penetration process acts to raise the thermal state of impacting projectiles ; resulting in fragmentation, melting, and vaporization at lower velocities than with traditional shielding configurations (e.g. Whipple shield). In order to characterize the protective capability of these structures, an extensive experimental campaign was performed by the Johnson Space Center Hypervelocity Impact Technology Facility, the results of which are reported in this paper. Although not capable of competing against the protection levels achievable with leading heavy shields in use on modern high-risk vehicles (i.e. International Space Station modules), metallic foam core sandwich panels are shown to provide a substantial improvement over comparable structural panels and traditional low weight shielding alternatives such as honeycomb sandwich panels and metallic Whipple shields. A ballistic limit equation, generalized in terms of panel geometry, is derived and presented in a form suitable for application in risk assessment codes.

Fabrication of metallic honeycomb panels for reusable TPS - structures

International Nuclear Information System (INIS)

Tabernig, B.; Thierfelder, W.; Alber, H.; Sudmeijer, K.

2001-01-01

The manufacturing technology with specific regard to high temperature brazing was developed to fabricate a honeycomb panel consisting of a thin-sectioned PM 2000 core material sandwiched on both sides with PM 1000 face sheets. For brazing the PM 1000 / PM 2000 panel the braze alloy PdNi was selected due to the best oxidation behavior while good mechanical properties and wetting behavior compared with other tested filler alloys. To examine the concept of a hybrid PM 1000/2000 panel as a stiffened skin panel a number of engineering test samples of sub-scale and two full-size panels were fabricated at Plansee AG and supplied to Fokker Space for testing under representative in-service conditions. Engineering tests showed that the test samples were rather insensitive to temperature gradients even at temperature differences between the face sheets of 550 o C. The engineering test samples exhibited no plastic deformation after testing at different heating rates ranging from 5 to 40 o C/s and at temperature profiles representative for two flights. The requirement for the designed application regarding impact properties at low as well as high speed were met. Impact at low speed with an energy of 8 J did not cause any cracks. Hail tests where ice bullets were fired with speeds to 208 m/s at different angles from 25 o to 90 o C against the test piece showed no damage at 25 o and caused slight indentation at 45 o and cracks at 90 o , which demonstrated a good performance for the fly through a hail cloud without any problems. In tests to determine the response of a full-size panel to a number of simulated thermo-mechanical flight load cycles the panel passed 50 cycles successfully without damage. (author)

Creation of a U.S. Phosphorescent OLED Lighting Panel Manufacturing Facility

Energy Technology Data Exchange (ETDEWEB)

Hack, Michael

2013-09-30

Universal Display Corporation (UDC) has pioneered high efficacy phosphorescent OLED (PHOLED™) technology to enable the realization of an exciting new form of high quality, energy saving solid-date lighting. In laboratory test devices, we have demonstrated greater than 100 lm/W conversion efficacy. In this program, Universal Display will demonstrate the scalability of its proprietary UniversalPHOLED technology and materials for the manufacture of white OLED lighting panels that meet commercial lighting targets. Moser Baer Technologies will design and build a U.S.- based pilot facility. The objective of this project is to establish a pilot phosphorescent OLED (PHOLED) manufacturing line in the U.S. Our goal is that at the end of the project, prototype lighting panels could be provided to U.S. luminaire manufacturers for incorporation into products to facilitate the testing of design concepts and to gauge customer acceptance, so as to facilitate the growth of the embryonic U.S. OLED lighting industry. In addition, the team will provide a cost of ownership analysis to quantify production costs including OLED performance metrics which relate to OLED cost such as yield, materials usage, cycle time, substrate area, and capital depreciation. This project was part of a new DOE initiative designed to help establish and maintain U.S. leadership in this program will support key DOE objectives by showing a path to meet Department of Energy Solid-State Lighting Manufacturing Roadmap cost targets, as well as meeting its efficiency targets by demonstrating the energy saving potential of our technology through the realization of greater than 76 lm/W OLED lighting panels by 2012.

Plasma Science Committee (PLSC) and the Panel on Opportunities in Plasma Science and Technology (OPST)

International Nuclear Information System (INIS)

1993-01-01

The Plasma Science Committee (PLSC) of the National Research Council (NRC) is charged with monitoring the health of the field of plasma science in the United States and identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special symposia are among the mechanisms used by the PLSC to meet its charge. During July 1992, the PLSC sponsored a workshop on nonneutral plasmas in traps. Although no written report on the workshop results, was prepared for public distribution, a summary of highlights was provided to the OPST Subpanel on Nonneutral Plasmas. The PLSC also continued its follow-up briefings and discussions on the results of the results of the report Plasma Processing of materials. Scientific and Technological Opportunities. As a result of these activities, the Committee is now working with the NRC Committee on Atomic, Molecular, and Optical Sciences (CAMOS) to organize a symposium on database needs in plasma processing of materials

Proficiency testing for sensory profile panels : measuring panel performance

NARCIS (Netherlands)

Mcewan, J.A.; Hunter, E.A.; Gemert, L.J. van; Lea, P.

2002-01-01

Proficiency testing in sensory analysis is an important step towards demonstrating that results from one sensory panel are consistent with the results of other sensory panels. The uniqueness of sensory analysis poses some specific problems for measuring the proficiency of the human instrument

WTEC panel report on European nuclear instrumentation and controls. Final report

International Nuclear Information System (INIS)

White, J.D.; Lanning, D.D.; Beltracchi, L.; Best, F.R.; Easter, J.R.

1991-12-01

A study of instrumentation and controls (I and C) technology used in nuclear power plants in Europe was conducted by a panel of American specialists. The study included a review of the literature on the subject, followed by a visit to some of the leading organizations in Europe in the field of nuclear I and C. The findings of the study are presented in the report. The scope is limited to pressurized water reactors in Czechoslovakia, France, Germany, Norway and Russia. Specific topics include: The role of the operator and control room design; the transition from analog to digital technology; computerized operator support systems for fault management; control strategies and techniques; an investigation of nuclear power plant I and C architecture; instrumentation; computer standards and tools. A companion study is JTEC Panel Report on Nuclear Power in Japan (PB90-215724)

Advanced optical instruments technology

Science.gov (United States)

Shao, Mike; Chrisp, Michael; Cheng, Li-Jen; Eng, Sverre; Glavich, Thomas; Goad, Larry; Jones, Bill; Kaarat, Philip; Nein, Max; Robinson, William

1992-08-01

The science objectives for proposed NASA missions for the next decades push the state of the art in sensitivity and spatial resolution over a wide range of wavelengths, including the x-ray to the submillimeter. While some of the proposed missions are larger and more sensitive versions of familiar concepts, such as the next generation space telescope, others use concepts, common on the Earth, but new to space, such as optical interferometry, in order to provide spatial resolutions impossible with other concepts. However, despite their architecture, the performance of all of the proposed missions depends critically on the back-end instruments that process the collected energy to produce scientifically interesting outputs. The Advanced Optical Instruments Technology panel was chartered with defining technology development plans that would best improve optical instrument performance for future astrophysics missions. At this workshop the optical instrument was defined as the set of optical components that reimage the light from the telescope onto the detectors to provide information about the spatial, spectral, and polarization properties of the light. This definition was used to distinguish the optical instrument technology issues from those associated with the telescope, which were covered by a separate panel. The panel identified several areas for optical component technology development: diffraction gratings; tunable filters; interferometric beam combiners; optical materials; and fiber optics. The panel also determined that stray light suppression instruments, such as coronagraphs and nulling interferometers, were in need of general development to support future astrophysics needs.

Large thermal protection system panel

Science.gov (United States)

Weinberg, David J. (Inventor); Myers, Franklin K. (Inventor); Tran, Tu T. (Inventor)

2003-01-01

A protective panel for a reusable launch vehicle provides enhanced moisture protection, simplified maintenance, and increased temperature resistance. The protective panel includes an outer ceramic matrix composite (CMC) panel, and an insulative bag assembly coupled to the outer CMC panel for isolating the launch vehicle from elevated temperatures and moisture. A standoff attachment system attaches the outer CMC panel and the bag assembly to the primary structure of the launch vehicle. The insulative bag assembly includes a foil bag having a first opening shrink fitted to the outer CMC panel such that the first opening and the outer CMC panel form a water tight seal at temperatures below a desired temperature threshold. Fibrous insulation is contained within the foil bag for protecting the launch vehicle from elevated temperatures. The insulative bag assembly further includes a back panel coupled to a second opening of the foil bag such that the fibrous insulation is encapsulated by the back panel, the foil bag, and the outer CMC panel. The use of a CMC material for the outer panel in conjunction with the insulative bag assembly eliminates the need for waterproofing processes, and ultimately allows for more efficient reentry profiles.

Reflecting variable opening insulating panel

International Nuclear Information System (INIS)

Nungesser, W.T.

1976-01-01

A description is given of a reflecting variable opening insulating panel assembly, comprising a static panel assembly of reflecting insulation sheets forming a cavity along one side of the panel and a movable panel opening out by sliding from the cavity of the static panel, and a locking device for holding the movable panel in a position extending from the cavity of the static panel. This can apply to a nuclear reactor of which the base might require maintenance and periodical checking and for which it is desirable to have available certain processes for the partial dismantling of the insulation [fr

WTEC Panel on Power applications of superconductivity in Japan and Germany. Final report

International Nuclear Information System (INIS)

Shelton, R.D.; Larbalestier, David; Blaugher, Richard D.; Schwall, Robert E.; Sokolowski, Robert S.; Suenaga, Masaki; Willis, JefFR-ey O.

1997-01-01

In early 1996, the U.S. Department of Energy and National Science Foundation asked the World Technology Evaluation Center (WTEC) to assemble a panel to assess, relative to the United States, how Japan and Germany are responding to the challenge of applying superconductivity to power and energy applications. Although the study was focused mostly on the impact of high-temperature superconductors (HTS) on the power applications field, the WTEC panel also looked at many applications for low-temperature superconductors (LTS). The market for low-temperature superconductor applications is well established, as is that for superconducting electronics, for which there is a separate WTEC panel. The panel on power applications of superconductivity was commissioned to identify the roles of public organizations, industry, and academia for advancing power applications of superconductivity, taking both a present and a long-term view

WTEC Panel on Power applications of superconductivity in Japan and Germany. Final report

CERN Document Server

Shelton, R D; Larbalestier, D; Schwall, R E; Sokolowski, R S; Suenaga, M; Willis, J E O

1997-01-01

In early 1996, the U.S. Department of Energy and National Science Foundation asked the World Technology Evaluation Center (WTEC) to assemble a panel to assess, relative to the United States, how Japan and Germany are responding to the challenge of applying superconductivity to power and energy applications. Although the study was focused mostly on the impact of high-temperature superconductors (HTS) on the power applications field, the WTEC panel also looked at many applications for low-temperature superconductors (LTS). The market for low-temperature superconductor applications is well established, as is that for superconducting electronics, for which there is a separate WTEC panel. The panel on power applications of superconductivity was commissioned to identify the roles of public organizations, industry, and academia for advancing power applications of superconductivity, taking both a present and a long-term view.

Development of a Thin-Wall Magnesium side door Inner Panel for Automobiles

Energy Technology Data Exchange (ETDEWEB)

Jekl, J.; Auld, J.; Sweet, C.; Carter, Jon; Resch, Steve; Klarner, A.; Brevick, J.; Luo, A.

2015-05-17

Cast magnesium side door inner panels can provide a good combination of weight, functional, manufacturing and economical requirements. However, several challenges exist including casting technology for thin-wall part design, multi-material incompatibility and relatively low strength vs steel. A project has been initiated, supported by the US Department of Energy, to design and develop a lightweight frame-under-glass door having a thin-wall, full die-cast, magnesium inner panel. This development project is the first of its kind within North America. Phase I of the project is now complete and the 2.0mm magnesium design, through casting process enablers, has met or exceeded all stiffness requirements, with significant mass reduction and part consolidation. In addition, a corrosion mitigation strategy has been established using industry-accepted galvanic isolation methods and coating technologies.

Puncture panel optimization

International Nuclear Information System (INIS)

Glass, R.E.; Longenbaugh, R.S.

1986-01-01

Sandia National Laboratories developed the TRansUranic PACkage Transporter (TRUPACT) to transport defense contact-handled transuranic wastes. The package has been designed to meet the normal and hypothetical accident conditions in 10CFR71 which includes the demonstrated ability to survive a 1-meter drop onto a mild steel pin. The puncture protection is provided by puncture resistant panels. In conjunction with the development of TRUPACT, a series of experiments has been conducted to reduce the weight of the puncture resistant panels. The initial scoping tests resulted in a preliminary design incorporating 30 layers of Kevlar. This design has been shown to meet the regulatory puncture test. To reduce the weight of this panel, subscale tests were conducted on panels utilizing Kevlar yarns with varying mass per unit length (denier) as well as different resins. This paper reviews the testing undertaken in the original panel development and discusses the results obtained from the recent subscale and full-scale optimization tests

Cavity Control and Panel Control Strategies in Double-Panel Structures for Transmitted Noise Reduction

NARCIS (Netherlands)

Ho, J.; Kalverboer, J.; Berkhoff, Arthur P.

2012-01-01

Investigation and comparisons of the cavity control and the panel control in a double-panel structure are presented in this paper. The double-panel structure, which comprises two panels with air in the gap, provides the advantages of low sound-transmission at high frequency, low heat-transmission

Hepatic (Liver) Function Panel

Science.gov (United States)

... Educators Search English Español Blood Test: Hepatic (Liver) Function Panel KidsHealth / For Parents / Blood Test: Hepatic (Liver) ... kidneys ) is working. What Is a Hepatic (Liver) Function Panel? A liver function panel is a blood ...

Panel Resonance Control and Cavity Control in Double-Panel Structures for Active Noise Reduction

NARCIS (Netherlands)

Ho, J.; Berkhoff, Arthur P.

2011-01-01

An analytical and experimental investigation of panel resonance control and cavity control in a double-panel structure is presented in this paper. The double-panel structure, which consists of two panels with air in the gap, is widely adopted in many applications such as aerospace due to its low

Polymer Industrial Floors - The Possibility of Using Secondary Raw Materials from Solar Panels

OpenAIRE

J. Kosikova; B. Vacenovska; M. Vyhnankova

2014-01-01

The paper reports on the subject of recycling and further use of secondary raw materials obtained from solar panels, which is becoming a very up to date topic in recent years. Recycling these panels is very difficult and complex, and the use of resulting secondary raw materials is still not fully resolved. Within the research carried out at the Brno University of Technology, new polymer materials used for industrial floors are being developed. Secondary raw materials are ...

Panel 1 - comparative evaluation of deposition technologies

Energy Technology Data Exchange (ETDEWEB)

Fenske, G.R.; Stodolsky, F. [Argonne National Lab., IL (United States); Benson, D.K.; Pitts, R.J. [National Renewable Energy Lab., Golden, CO (United States); Bhat, D.G. [GTE Valenite Corp., Troy, MI (United States); Yulin Chen [Allison Gas Turbine Division, GM, Indianapolis, IN (United States); Gat, R.; Sunkara, M.K. [Case Western Reserve Univ., Cleveland, OH (United States); Kelly, M. [Stanford Univ., CA (United States); Lawler, J.E. [Univ. of Wisconsin, Madison (United States); Nagle, D.C. [Martin Marietta Labs., Baltimore, MD (United States); Outka, D. [Sandia National Laboratories, Livermore, CA (United States); Revankar, G.S. [Deere & Co., Moline, IL (United States); Subramaniam, V.V. [Ohio State Univ., Columbus (United States); Wilbur, P.J. [Colorado State Univ., Fort Collins (United States); Mingshow Wong [Northwestern Univ., Evanston, IL (United States); Woolam, W.E. [Southwest Research Inst., Arlington, VA (United States)

1993-01-01

This working group attempted to evaluate/compare the different types of deposition techniques currently under investigation for depositing diamond and diamond-like carbon films. A table lists the broad types of techniques that were considered for depositing diamond and diamond-like carbon films. After some discussion, it was agreed that any evaluation of the various techniques would be dependent on the end application. Thus the next action was to list the different areas where diamond and DLC films could find applications in transportation. These application areas are listed in a table. The table intentionally does not go into great detail on applications because that subject is dealt with specifically by Panel No. 4 - Applications To Transportation. The next action concentrated on identifying critical issues or limitations that need to be considered in evaluating the different processes. An attempt was then made to rank different broad categories of deposition techniques currently available or under development based on the four application areas and the limitations. These rankings/evaluations are given for diamond and DLC techniques. Finally, the working group tried to identify critical development and research issues that need to be incorporated into developing a long-term program that focuses on diamond/DLC coatings for transportation needs. 5 tabs.

77 FR 25685 - Malcolm Baldrige National Quality Award Panel of Judges

Science.gov (United States)

2012-05-01

... members prominent in the fields of quality, innovation, and performance management and appointed by the..., Maryland 20899. FOR FURTHER INFORMATION CONTACT: Dr. Harry Hertz, Director, Baldrige Performance Excellence... Quality Award Panel of Judges AGENCY: National Institute of Standards and Technology, Department of...

76 FR 44577 - Malcolm Baldrige National Quality Award Panel of Judges

Science.gov (United States)

2011-07-26

... prominent in the fields of quality, innovation, and performance management and appointed by the Secretary of.... FOR FURTHER INFORMATION CONTACT: Dr. Harry Hertz, Director, Baldrige Performance Excellence Program... Quality Award Panel of Judges AGENCY: National Institute of Standards and Technology, Department of...

Performance comparison between silicon solar panel and dye-sensitized solar panel in Malaysia

Science.gov (United States)

Hamed, N. K. A.; Ahmad, M. K.; Urus, N. S. T.; Mohamad, F.; Nafarizal, N.; Ahmad, N.; Soon, C. F.; Ameruddin, A. S.; Faridah, A. B.; Shimomura, M.; Murakami, K.

2017-09-01

In carrying out experimental research in performance between silicon solar panel and dye-sensitive solar panel, we have been developing a device and a system. This system has been developed consisting of controllers, hardware and software. This system is capable to get most of the input sources. If only need to change the main circuit and coding for a different source input value. This device is able to get the ambient temperature, surface temperature, surrounding humidity, voltage with load, current with load, voltage without load and current without load and save the data into external memory. This device is able to withstand the heat and rain as it was fabricated in a waterproof box. This experiment was conducted to examine the performance of both the solar panels which are capable to maintain their stability and performance. A conclusion based on data populated, the distribution of data for dye-sensitized solar panel is much better than silicon solar panel as dye-sensitized solar panel is very sensitive to heat and not depend only on midday where is that is the maximum ambient temperature for both solar panel as silicon solar panel only can give maximum and high output only when midday.

The digital flat-panel X-Ray detectors

International Nuclear Information System (INIS)

Risticj, S. Goran

2013-01-01

In a digital imaging system, the incident x-ray image must be sampled both in the spatial and intensity dimensions. In the spatial dimensions, samples are obtained as averages of the intensity over picture elements or pixels. In the intensity dimension, the signal is digitalized into one of a finite number of levels or bits. Two main types of digital flat-panel detectors are based on the direct conversion, which contains the photoconductor, and on indirect conversion, which contains phosphor. The basics of these detectors are given. Coupling traditional x-ray detection material such as photoconductors and phosphors with a large-area active-matrix readout structure forms the basis of flat panel x-ray images. Active matrix technology provides a new, highly efficient, real time method for electronically storing and measuring the product of the x-ray interaction stage whether the product is visible wavelength photons or electrical charges. The direct and indirect detectors, made as the active-matrix flat-panel detectors containing sensing/storage elements, switching elements (diodes or thin film transistors (TFTS)) and image processing module, are described. Strengths and limitations of stimulable phosphors are discussed. The main advantages and disadvantages of mentioned x-ray detectors are also analyzed. (Author)

Development of circuit model for arcing on solar panels

International Nuclear Information System (INIS)

Mehta, Bhoomi K; Deshpande, S P; Mukherjee, S; Gupta, S B; Ranjan, M; Rane, R; Vaghela, N; Acharya, V; Sudhakar, M; Sankaran, M; Suresh, E P

2010-01-01

The increased requirements of payload capacity of the satellites have resulted in much higher power requirements of the satellites. In order to minimize the energy loss during power transmission due to cable loss, use of high voltage solar panels becomes necessary. When a satellite encounters space plasma it floats negatively with respect to the surrounding space plasma environment. At high voltage, charging and discharging on solar panels causes the power system breakdown. Once a solar panel surface is charged and potential difference between surface insulator and conductor exceeds certain value, electrostatic discharge (ESD) may occur. This ESD may trigger a secondary arc that can destroy the solar panel circuit. ESD is also called as primary or minor arc and secondary is called major arc. The energy of minor arc is supplied by the charge stored in the coverglass of solar array and is a pulse of typically several 100 ns to several 100 μs duration. The damage caused by minor arc is less compared to major arcs, but it is observed that the minor arc is cause of major arc. Therefore it is important to develop an understanding of minor arc and mitigation techniques. In this paper we present a linear circuit analysis for minor arcs on solar panels. To study arcing event, a ground experimental facility to simulate space plasma environment has been developed at Facilitation Centre for Industrial Plasma Technologies (Institute for Plasma Research) in collaboration with Indian Space Research Organization's ISRO Satellite Technology Centre (ISAC). A linear circuit model has been developed to explain the experimental results by representing the coverglass, solar cell interconnect and wiring by an LCR circuit and the primary arc by an equivalent LR circuit. The aim of the circuit analysis is to predict the arc current which flows through the arc plasma. It is established from the model that the current depends on various parameters like potential difference between insulator

Experimental investigation to evaluate the potential environmental hazards of photovoltaic panels.

Science.gov (United States)

Tammaro, Marco; Salluzzo, Antonio; Rimauro, Juri; Schiavo, Simona; Manzo, Sonia

2016-04-05

Recently the potential environmental hazard of photovoltaic modules together with their management as waste has attracted the attention of scientists. Particular concern is aroused by the several metals contained in photovoltaic panels whose potential release in the environment were scarcely investigated. Here, for the first time, the potential environmental hazard of panels produced in the last 30 years was investigated through the assessment of up to 18 releasable metals. Besides, the corresponding ecotoxicological effects were also evaluated. Experimental data were compared with the current European and Italian law limits for drinking water, discharge on soil and landfill inert disposal in order to understand the actual pollution load. Results showed that less than 3% of the samples respected all law limits and around 21% was not ecotoxic. By considering the technological evolutions in manufacturing, we have shown that during the years crystalline silicon panels have lower tendency to release hazardous metals with respect to thin film panels. In addition, a prediction of the amounts of lead, chromium, cadmium and nickel releasable from next photovoltaic waste was performed. The prevision up to 2050 showed high amounts of lead (30t) and cadmium (2.9t) releasable from crystalline and thin film panels respectively. Copyright © 2015 Elsevier B.V. All rights reserved.

Antinuclear antibody panel

Science.gov (United States)

... page: //medlineplus.gov/ency/article/003535.htm Antinuclear antibody panel To use the sharing features on this page, please enable JavaScript. The antinuclear antibody panel is a blood test that looks at ...

Hepatitis virus panel

Science.gov (United States)

... page: //medlineplus.gov/ency/article/003558.htm Hepatitis virus panel To use the sharing features on this page, please enable JavaScript. The hepatitis virus panel is a series of blood tests used ...

REINFORCED COMPOSITE PANEL

DEFF Research Database (Denmark)

2003-01-01

A composite panel having front and back faces, the panel comprising facing reinforcement, backing reinforcement and matrix material binding to the facing and backing reinforcements, the facing and backing reinforcements each independently comprising one or more reinforcing sheets, the facing rein...... by matrix material, the facing and backing reinforcements being interconnected to resist out-of-plane relative movement. The reinforced composite panel is useful as a barrier element for shielding structures, equipment and personnel from blast and/or ballistic impact damage....

Rational Design of Composite Panels

DEFF Research Database (Denmark)

Riber, Hans Jørgen

1996-01-01

A non-linear structural model for composite panels is presented. The non-linear terms in the lateral displacements are modelled as an additional set of lateral loads acting on the panel. Hence the solution is reduced to that of an equivalent panel with small displacements In order to treat sandwich...... Norske Veritas', DNV, building rules concerning high-speed light craft, in which the panel scantlings are often restricted by a maximum lateral deflection connected with the panel span....

Composite panel development at JPL

Science.gov (United States)

Mcelroy, Paul; Helms, Rich

1988-01-01

Parametric computer studies can be use in a cost effective manner to determine optimized composite mirror panel designs. An InterDisciplinary computer Model (IDM) was created to aid in the development of high precision reflector panels for LDR. The materials properties, thermal responses, structural geometries, and radio/optical precision are synergistically analyzed for specific panel designs. Promising panels designs are fabricated and tested so that comparison with panel test results can be used to verify performance prediction models and accommodate design refinement. The iterative approach of computer design and model refinement with performance testing and materials optimization has shown good results for LDR panels.

Next-generation air measurement technologies | Science ...

Science.gov (United States)

This is a presentation at a workshop in Chicago on emerging air monitoring technologies, hosted by a local nonprofit. The audience is composed of a mixture of technical backgrounds. This presentation will be part of an opening panel and the goal is to give an overview of the state of science on emerging air sensor technology. This is a presentation at a workshop in Chicago on emerging air monitoring technologies, hosted by a local nonprofit. The audience is composed of a mixture of technical backgrounds. This presentation will be part of an opening panel and the goal is to give an overview of the state of science on emerging air sensor technology.

Independent Panel Evaluation of Dry Sludge PISA Program

International Nuclear Information System (INIS)

Fondeur, F.F.

1999-01-01

Dr. Kirk Yeager and Mr. Marvin Banks from Energetic Material Research and Technology Center (EMRTC) evaluated the Savannah River Site (SRS) efforts in the Dry Sludge program. They evaluated four program areas: energetic material formation, stability, initiation, and propagation. The panel evaluation included a site visit (July 13, 1999 and July 14, 1999) as well as a review of various reports and presentations by researchers involved in the program

Independent Panel Evaluation of Dry Sludge PISA Program

Energy Technology Data Exchange (ETDEWEB)

Fondeur, F.F.

1999-10-20

Dr. Kirk Yeager and Mr. Marvin Banks from Energetic Material Research and Technology Center (EMRTC) evaluated the Savannah River Site (SRS) efforts in the Dry Sludge program. They evaluated four program areas: energetic material formation, stability, initiation, and propagation. The panel evaluation included a site visit (July 13, 1999 and July 14, 1999) as well as a review of various reports and presentations by researchers involved in the program.

Supersonic Panel Flutter Test Results for Flat Fiber-Glass Sandwich Panels with Foamed Cores

Science.gov (United States)

Tuovila, W. J.; Presnell, John G., Jr.

1961-01-01

Flutter tests have been made on flat panels having a 1/4 inch-thick plastic-foam core covered with thin fiber-glass laminates. The testing was done in the Langley Unitary Plan wind tunnel at Mach numbers from 1.76 t o 2.87. The flutter boundary for these panels was found to be near the flutter boundary of thin metal panels when compared on the basis of an equivalent panel stiffness. The results also demonstrated that the depth of the cavity behind the panel has a pronounced influence on flutter. Changing the cavity depth from 1 1/2 inches to 1/2 inch reduced the dynamic pressure at start of flutter by 40 percent. No flutter was obtained when the spacers on the back of the panel were against the bottom of the cavity.

Panel Resource Management (PRM) Implementation and Effects within Safety Review Panel Settings and Dynamics

Science.gov (United States)

Taylor, Robert W.; Nash, Sally K.

2007-01-01

While technical training and advanced degree's assure proficiency at specific tasks within engineering disciplines, they fail to address the potential for communication breakdown and decision making errors familiar to multicultural environments where language barriers, intimidating personalities and interdisciplinary misconceptions exist. In an effort to minimize these pitfalls to effective panel review, NASA's lead safety engineers to the ISS Safety Review Panel (SRP), and Payload Safety Review Panel (PSRP) initiated training with their engineers, in conjunction with the panel chairs, and began a Panel Resource Management (PRM) program. The intent of this program focuses on the ability to reduce the barriers inhibiting effective participation from all panel attendees by bolstering participants confidence levels through increased communication skills, situational awareness, debriefing, and a better technical understanding of requirements and systems.

Solar panel cleaning robot

Science.gov (United States)

Nalladhimmu, Pavan Kumar Reddy; Priyadarshini, S.

2018-04-01

As the demand of electricity is increasing, there is need to using the renewable sources to produce the energy at present of power shortage, the use of solar energy could be beneficial to great extent and easy to get the maximum efficiency. There is an urgent in improving the efficiency of solar power generation. Current solar panels setups take a major power loss when unwanted obstructions cover the surface of the panels. To make solar energy more efficiency of solar array systems must be maximized efficiency evaluation of PV panels, that has been discussed with particular attention to the presence of dust on the efficiency of the PV panels have been highlighted. This paper gives the how the solar panel cleaning system works and designing of the cleaning system.

Control room, emergency control system and local control panels in nuclear power plants

International Nuclear Information System (INIS)

1988-01-01

The requirements on planning and construction of control boards including ergonomic-technical designing are specified in this rule. The specifications put the requirements on the design of place, process and environment of work, which are mentioned in the sections 90 and 91 of the labor-management relations act, into more concrete terms for the safety-relevant control panels as work places in a nuclear power station. The work places at control panels are not considered as video workstations in the sense of the 'Safety Rules for Video Workstations in the Office Sector' published by the General Association of the Industrial Trade Associations. The requirements are based on the operation and information technology realized at present in control panels of stationary nuclear power plants. (orig./HP) [de

Compressive Behavior of Frame-Stiffened Composite Panels

Science.gov (United States)

Yovanof, Nicolette P.; Jegley, Dawn C.

2011-01-01

New technologies are being developed under NASA's Environmentally Responsible Aviation (ERA) Program aimed at reducing fuel burn and emissions in large commercial aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is being developed which offers advantages over traditional metallic structure. In this concept a stitched carbon-epoxy material system is employed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners and producing a more damage tolerant design. In addition, by adding unidirectional carbon rods to the top of stiffeners and minimizing the interference between the sandwich frames and the rod-stiffened stringers, the panel becomes more structurally efficient. This document describes the results of experimentation on a PRSEUS panel in which the frames are loaded in unidirectional compression beyond the local buckling of the skin of a Hybrid Wing Body (HWB) aircraft. A comparison with analytical predictions and the relationship between these test results and the global aircraft design is presented.

Lightweight, Thermally Insulating Structural Panels

Science.gov (United States)

Eisen, Howard J.; Hickey, Gregory; Wen, Liang-Chi; Layman, William E.; Rainen, Richard A.; Birur, Gajanana C.

1996-01-01

Lightweight, thermally insulating panels that also serve as structural members developed. Honeycomb-core panel filled with low-thermal-conductivity, opacified silica aerogel preventing convection and minimizes internal radiation. Copper coating on face sheets reduces radiation. Overall thermal conductivities of panels smaller than state-of-art commercial non-structurally-supporting foam and fibrous insulations. On Earth, panels suitable for use in low-air-pressure environments in which lightweight, compact, structurally supporting insulation needed; for example, aboard high-altitude aircraft or in partially evacuated panels in refrigerators.

Experimental investigation to evaluate the potential environmental hazards of photovoltaic panels

Energy Technology Data Exchange (ETDEWEB)

Tammaro, Marco, E-mail: marco.tammaro@enea.it [ENEA, Italian National Agency for New Technologies, Energy and the Environment, Centre of Research of Portici Naples (Italy); Salluzzo, Antonio, E-mail: antonio.salluzzo@enea.it [ENEA, Italian National Agency for New Technologies, Energy and the Environment, Centre of Research of Portici Naples (Italy); Rimauro, Juri, E-mail: juri.rimauro@enea.it [ENEA, Italian National Agency for New Technologies, Energy and the Environment, Centre of Research of Portici Naples (Italy); Schiavo, Simona, E-mail: simona.schiavo@unina.it [University “Federico II” of Naples Via Università 100, 80055 Portici (Italy); Manzo, Sonia, E-mail: sonia.manzo@enea.it [ENEA, Italian National Agency for New Technologies, Energy and the Environment, Centre of Research of Portici Naples (Italy)

2016-04-05

Highlights: • We measure the metals released in the leaching solution by samples of PV panels. • We measure the environmental effects by a battery of ecotoxicological tests. • The experimental data are compared with the European and Italian benchmark limits. • We assess the potential emissions of metals from future PV waste. • Experimental results show that the photovoltaic panels present an environmental risk. - Abstract: Recently the potential environmental hazard of photovoltaic modules together with their management as waste has attracted the attention of scientists. Particular concern is aroused by the several metals contained in photovoltaic panels whose potential release in the environment were scarcely investigated. Here, for the first time, the potential environmental hazard of panels produced in the last 30 years was investigated through the assessment of up to 18 releasable metals. Besides, the corresponding ecotoxicological effects were also evaluated. Experimental data were compared with the current European and Italian law limits for drinking water, discharge on soil and landfill inert disposal in order to understand the actual pollution load. Results showed that less than 3% of the samples respected all law limits and around 21% was not ecotoxic. By considering the technological evolutions in manufacturing, we have shown that during the years crystalline silicon panels have lower tendency to release hazardous metals with respect to thin film panels. In addition, a prediction of the amounts of lead, chromium, cadmium and nickel releasable from next photovoltaic waste was performed. The prevision up to 2050 showed high amounts of lead (30 t) and cadmium (2.9 t) releasable from crystalline and thin film panels respectively.

PERBANDINGAN UNJUK KERJA ANTARA PANEL SEL SURYA BERPENJEJAK DENGAN PANEL SEL SURYA DIAM

OpenAIRE

Syafaruddin Ch

2010-01-01

The ability to produce electrical energy at Solar Power Plant  is highly dependent on the magnitude and duration of sun exposure on the solar cell panels. The movement of the sun from east to west that periodicity in every day is a problem at  the  optimization generation of electricity at  Solar Power Plant   if using solar panel that motionless. This is because the solar cell panel can not catch the maximum sun exposure. To solve the above problem then designed a solar cell panel  tracker...

Panel data analysis using EViews

CERN Document Server

Agung, I Gusti Ngurah

2013-01-01

A comprehensive and accessible guide to panel data analysis using EViews software This book explores the use of EViews software in creating panel data analysis using appropriate empirical models and real datasets. Guidance is given on developing alternative descriptive statistical summaries for evaluation and providing policy analysis based on pool panel data. Various alternative models based on panel data are explored, including univariate general linear models, fixed effect models and causal models, and guidance on the advantages and disadvantages of each one is given. Panel Data Analysis

RECIPANEL: RECYCLED PAPER PANELS

Directory of Open Access Journals (Sweden)

HERNÁN CAÑOLA

2012-01-01

Full Text Available En este artículo se estudia la fabricación y el comportamiento mecánico de paneles a base de papel reciclado. El objetivo principal del proyecto es producir un prototipo de panel que emplee elementos provenientes de residuos sólidos (papel periódico y de un material conglomerante (cemento Portland blanco. El panel debe ser económico, debe tener buenas propiedades mecánicas y debe tener dimensiones comerciales para su uso en muros tabiques y en cielos falsos en la industria de la construcción. El Recipanel es un panel no estructural a base de papel reciclado. El Recipanel cumple las normas colombianas en lo relativo a los paneles de uso no estructural y presenta además unas excelentes características mecánicas.

Report of panel 1: The appropriate scope and mission of ITER

Energy Technology Data Exchange (ETDEWEB)

Linford, R.K. (Los Alamos National Lab., NM (United States)); Weitzner, H.; Abdou, M.A.; Baldwin, D.E.; Berkner, K.H.; Berry, L.A.; Culler, F.L.; Dean, S.O.; DeFreece, D.A.; Gauster, W.B. (and others)

1992-12-01

This panel looked at the mission of ITER, and how the US should address the present plans, and considers a number of alternative plans to arrive at the eventual goals of ITER. The panel considered three major approaches which have been discussed on the international scale, and tries to present the strengths, weaknesses, and possible changes to these plans. It suggests that any of these plans can arrive at the eventual aim, but may involve differing risks and time commitments. All plans involve ITER design studies, development work on technologies which must be in place for ITER design to succeed, and testing of materials and components for application in the device.

Report of panel 1: The appropriate scope and mission of ITER

International Nuclear Information System (INIS)

Linford, R.K.; Weitzner, H.; Abdou, M.A.; Baldwin, D.E.; Berkner, K.H.; Berry, L.A.; Culler, F.L.; Dean, S.O.; DeFreece, D.A.; Gauster, W.B.

1992-01-01

This panel looked at the mission of ITER, and how the US should address the present plans, and considers a number of alternative plans to arrive at the eventual goals of ITER. The panel considered three major approaches which have been discussed on the international scale, and tries to present the strengths, weaknesses, and possible changes to these plans. It suggests that any of these plans can arrive at the eventual aim, but may involve differing risks and time commitments. All plans involve ITER design studies, development work on technologies which must be in place for ITER design to succeed, and testing of materials and components for application in the device

78 FR 63168 - Judges Panel of the Malcolm Baldrige National Quality Award

Science.gov (United States)

2013-10-23

... INFORMATION CONTACT: Robert Fangmeyer, Acting Director, Baldrige Performance Excellence Program, National... Baldrige National Quality Award AGENCY: National Institute of Standards and Technology, Department of... Quality Award (Judges Panel) will meet in closed session Monday through Friday, November 4-8, 2013, 8:30 a...

Make Your Own Solar Panel.

Science.gov (United States)

Suzuki, David

1992-01-01

Presents an activity in which students make a simulated solar panel to learn about the principles behind energy production using solar panels. Provides information about how solar panels function to produce energy. (MCO)

Arginine Vasotocin, the Social Neuropeptide of Amphibians and Reptiles

Science.gov (United States)

Wilczynski, Walter; Quispe, Maricel; Muñoz, Matías I.; Penna, Mario

2017-01-01

Arginine vasotocin (AVT) is the non-mammalian homolog of arginine vasopressin (AVP) and, like vasopressin, serves as an important modulator of social behavior in addition to its peripheral functions related to osmoregulation, reproductive physiology, and stress hormone release. In amphibians and reptiles, the neuroanatomical organization of brain AVT cells and fibers broadly resembles that seen in mammals and other taxa. Both parvocellular and magnocellular AVT-containing neurons are present in multiple populations located mainly in the basal forebrain from the accumbens–amygdala area to the preoptic area and hypothalamus, from which originate widespread fiber connections spanning the brain with a particularly heavy innervation of areas associated with social behavior and decision-making. As for mammalian AVP, AVT is present in greater amounts in males in many brain areas, and its presence varies seasonally, with hormonal state, and in males with differing social status. AVT’s social influence is also conserved across herpetological taxa, with significant effects on social signaling and aggression, and, based on the very small number of studies investigating more complex social behaviors in amphibians and reptiles, AVT may also modulate parental care and social bonding when it is present in these vertebrates. Within this conserved pattern, however, both AVT anatomy and social behavior effects vary significantly across species. Accounting for this diversity represents a challenge to understanding the mechanisms by which AVT exerts its behavioral effects, as well are a potential tool for discerning the structure-function relationships underlying AVT’s many effects on behavior. PMID:28824546

Arginine Vasotocin, the Social Neuropeptide of Amphibians and Reptiles

Directory of Open Access Journals (Sweden)

Walter Wilczynski

2017-08-01

Full Text Available Arginine vasotocin (AVT is the non-mammalian homolog of arginine vasopressin (AVP and, like vasopressin, serves as an important modulator of social behavior in addition to its peripheral functions related to osmoregulation, reproductive physiology, and stress hormone release. In amphibians and reptiles, the neuroanatomical organization of brain AVT cells and fibers broadly resembles that seen in mammals and other taxa. Both parvocellular and magnocellular AVT-containing neurons are present in multiple populations located mainly in the basal forebrain from the accumbens–amygdala area to the preoptic area and hypothalamus, from which originate widespread fiber connections spanning the brain with a particularly heavy innervation of areas associated with social behavior and decision-making. As for mammalian AVP, AVT is present in greater amounts in males in many brain areas, and its presence varies seasonally, with hormonal state, and in males with differing social status. AVT’s social influence is also conserved across herpetological taxa, with significant effects on social signaling and aggression, and, based on the very small number of studies investigating more complex social behaviors in amphibians and reptiles, AVT may also modulate parental care and social bonding when it is present in these vertebrates. Within this conserved pattern, however, both AVT anatomy and social behavior effects vary significantly across species. Accounting for this diversity represents a challenge to understanding the mechanisms by which AVT exerts its behavioral effects, as well are a potential tool for discerning the structure-function relationships underlying AVT’s many effects on behavior.

Supporting public involvement in interview and other panels: a systematic review.

Science.gov (United States)

Baxter, Susan; Clowes, Mark; Muir, Delia; Baird, Wendy; Broadway-Parkinson, Andrea; Bennett, Carole

2017-10-01

Members of the public are increasingly being invited to become members of a variety of different panels and boards. This study aimed to systematically search the literature to identify studies relating to support or training provided to members of the public who are asked to be members of an interview panel. A systematic search for published and unpublished studies was carried out from June to September 2015. The search methods included electronic database searching, reference list screening, citation searching and scrutinizing online sources. We included studies of any design including published and unpublished documents which outlined preparation or guidance relating to public participants who were members of interview panels or representatives on other types of panels or committees. Results were synthesised via narrative methods. Thirty-six documents were included in the review. Scrutiny of this literature highlighted ten areas which require consideration when including members of the public on interview panels: financial resources; clarity of role; role in the interview process; role in evaluation; training; orientation/induction; information needs; terminology; support; and other public representative needs such as timing, accessibility and support with information technology. The results of the review emphasize a range of elements that need to be fully considered when planning the involvement of public participants on interview panels. It highlights potential issues relating to the degree of involvement of public representatives in evaluating/grading decisions and the need for preparation and on-going support. © 2016 The Authors. Health Expectations Published by John Wiley & Sons Ltd.

Solar panel parallel mounting configuration

Science.gov (United States)

Mutschler, Jr., Edward Charles (Inventor)

1998-01-01

A spacecraft includes a plurality of solar panels interconnected with a power coupler and an electrically operated device to provide power to the device when the solar cells are insolated. The solar panels are subject to bending distortion when entering or leaving eclipse. Spacecraft attitude disturbances are reduced by mounting each of the solar panels to an elongated boom made from a material with a low coefficient of thermal expansion, so that the bending of one panel is not communicated to the next. The boom may be insulated to reduce its bending during changes in insolation. A particularly advantageous embodiment mounts each panel to the boom with a single mounting, which may be a hinge. The single mounting prevents transfer of bending moments from the panel to the boom.

Seismic hazard analysis. Review panel, ground motion panel, and feedback results

International Nuclear Information System (INIS)

Bernreuter, D.L.

1981-10-01

The Site Specific Spectra Project (SSSP) was a multi-year study funded by the U.S. Nuclear Regulatory Commission to provide estimates of the seismic hazards at a number of nuclear power plant sites in the Eastern U.S. A key element of our approach was the Peer Review Panel, which we formed in order to ensure that our use of expert opinion was reasonable. We discuss the Peer Review Panel results and provide the complete text of each member's report. In order to improve the ground motion model, an Eastern U.S. Ground Motion Model Panel was formed. In Section 4 we tabulate the responses from the panel members to our feedback questionnaire and discuss the implications of changes introduced by them. We conclude that the net difference in seismic hazard values from those presented in Volume 4 is small and does not warrant a reanalysis. (author)

Lateral behavior of steel frames with discretely connected precast concrete infill panels

NARCIS (Netherlands)

Teeuwen, P.A.

2009-01-01

As an alternative to the conventional structures for tall buildings, a hybrid lateral load resisting structure has been designed at Eindhoven University of Technology. It consists of discretely connected precast concrete panels with window openings in steel frames, and is a new application in

Mounting clips for panel installation

Science.gov (United States)

Cavieres, Andres; Al-Haddad, Tristan; Goodman, Joseph

2017-07-11

A photovoltaic panel mounting clip comprising a base, central indexing tabs, flanges, lateral indexing tabs, and vertical indexing tabs. The mounting clip removably attaches one or more panels to a beam or the like structure, both mechanically and electrically. It provides secure locking of the panels in all directions, while providing guidance in all directions for accurate installation of the panels to the beam or the like structure.

Exergy metrication of radiant panel heating and cooling with heat pumps

International Nuclear Information System (INIS)

Kilkis, Birol

2012-01-01

Highlights: ► Rational Exergy Management Model analytically relates heat pumps and radiant panels. ► Heat pumps driven by wind energy perform better with radiantpanels. ► Better CO 2 mitigation is possible with wind turbine, heat pump, radiant panel combination. ► Energy savings and thermo-mechanical performance are directly linked to CO 2 emissions. - Abstract: Radiant panels are known to be energy efficient sensible heating and cooling systems and a suitable fit for low-exergy buildings. This paper points out the little known fact that this may not necessarily be true unless their low-exergy demand is matched with low-exergy waste and alternative energy resources. In order to further investigate and metricate this condition and shed more light on this issue for different types of energy resources and energy conversion systems coupled to radiant panels, a new engineering metric was developed. Using this metric, which is based on the Rational Exergy Management Model, true potential and benefits of radiant panels coupled to ground-source heat pumps were analyzed. Results provide a new perspective in identifying the actual benefits of heat pump technology in curbing CO 2 emissions and also refer to IEA Annex 49 findings for low-exergy buildings. Case studies regarding different scenarios are compared with a base case, which comprises a radiant panel system connected to a natural gas-fired condensing boiler in heating and a grid power-driven chiller in cooling. Results show that there is a substantial CO 2 emission reduction potential if radiant panels are optimally operated with ground-source heat pumps driven by renewable energy sources, or optimally matched with combined heat and power systems, preferably running on alternative fuels.

Development of admixture mapping panels for African Americans from commercial high-density SNP arrays

Directory of Open Access Journals (Sweden)

Dunston Georgia M

2010-07-01

Full Text Available Abstract Background Admixture mapping is a powerful approach for identifying genetic variants involved in human disease that exploits the unique genomic structure in recently admixed populations. To use existing published panels of ancestry-informative markers (AIMs for admixture mapping, markers have to be genotyped de novo for each admixed study sample and samples representing the ancestral parental populations. The increased availability of dense marker data on commercial chips has made it feasible to develop panels wherein the markers need not be predetermined. Results We developed two panels of AIMs (~2,000 markers each based on the Affymetrix Genome-Wide Human SNP Array 6.0 for admixture mapping with African American samples. These two AIM panels had good map power that was higher than that of a denser panel of ~20,000 random markers as well as other published panels of AIMs. As a test case, we applied the panels in an admixture mapping study of hypertension in African Americans in the Washington, D.C. metropolitan area. Conclusions Developing marker panels for admixture mapping from existing genome-wide genotype data offers two major advantages: (1 no de novo genotyping needs to be done, thereby saving costs, and (2 markers can be filtered for various quality measures and replacement markers (to minimize gaps can be selected at no additional cost. Panels of carefully selected AIMs have two major advantages over panels of random markers: (1 the map power from sparser panels of AIMs is higher than that of ~10-fold denser panels of random markers, and (2 clusters can be labeled based on information from the parental populations. With current technology, chip-based genome-wide genotyping is less expensive than genotyping ~20,000 random markers. The major advantage of using random markers is the absence of ascertainment effects resulting from the process of selecting markers. The ability to develop marker panels informative for ancestry from

Data Base Management Systems Panel. Third workshop summary

Science.gov (United States)

Urena, J. L. (Editor)

1981-01-01

The discussions and results of a review by a panel of data base management system (DRMS) experts of various aspects of the use of DBMSs within NASA/Office of Space and Terrestrial Applications (OSTA) and related organizations are summarized. The topics discussed included the present status of the use of DBMS technology and of the various ongoing DBMS-related efforts within NASA. The report drafts of a study that seeks to determine the functional requirements for a generalized DBMS for the NASA/OSTA and related data bases are examined. Future problems and possibilities with the use of DBMS technology are also considered. A list of recommendations for NASA/OSTA data systems is included.

HIFiRE-1 Turbulent Shock Boundary Layer Interaction - Flight Data and Computations (Postprint)

Science.gov (United States)

2015-06-01

STATEMENT. *//Signature// //Signature// ROGER L. KIMMEL MICHAEL S. BROWN, Chief Project Manager Hypersonic Sciences Branch...propulsion, propulsion-airframe integration, aerodynamics and aerothermodynamics, high temperature materials and structures, thermal management ...Stanfield, S., Borg , M., “Analysis of HIFiRE-1 Transition Data,” NATO Research and Technology Agency, Specialists Meeting AVT-200/RSM-030 on

Traditional methods v. new technologies - dilemmas for dietary assessment in large-scale nutrition surveys and studies: a report following an international panel discussion at the 9th International Conference on Diet and Activity Methods (ICDAM9), Brisbane, 3 September 2015.

Science.gov (United States)

Amoutzopoulos, B; Steer, T; Roberts, C; Cade, J E; Boushey, C J; Collins, C E; Trolle, E; de Boer, E J; Ziauddeen, N; van Rossum, C; Buurma, E; Coyle, D; Page, P

2018-01-01

The aim of the present paper is to summarise current and future applications of dietary assessment technologies in nutrition surveys in developed countries. It includes the discussion of key points and highlights of subsequent developments from a panel discussion to address strengths and weaknesses of traditional dietary assessment methods (food records, FFQ, 24 h recalls, diet history with interviewer-assisted data collection) v. new technology-based dietary assessment methods (web-based and mobile device applications). The panel discussion 'Traditional methods v. new technologies: dilemmas for dietary assessment in population surveys', was held at the 9th International Conference on Diet and Activity Methods (ICDAM9), Brisbane, September 2015. Despite respondent and researcher burden, traditional methods have been most commonly used in nutrition surveys. However, dietary assessment technologies offer potential advantages including faster data processing and better data quality. This is a fast-moving field and there is evidence of increasing demand for the use of new technologies amongst the general public and researchers. There is a need for research and investment to support efforts being made to facilitate the inclusion of new technologies for rapid, accurate and representative data.

Panel session: Disposal of HLW - ready for implementation

International Nuclear Information System (INIS)

Heremans, R.; Come, B.; Barbreau, A.; Girardi, F.

1986-01-01

The paper is a report of a panel session at the European Community conference on radioactive waste management and disposal, Luxembourg 1985, concerning the safe and long-term disposal of high-activity and long-lived waste. The subjects discussed include: geological barriers including deep sea-bed sediments, engineered barriers, technological problems (repository construction, waste emplacement, backfilling and sealing), safety analysis, performance assessment of disposal system components, and finally institutional, legal and financial aspects of geological disposal. (U.K.)

Projection display technologies for the new millennium

Science.gov (United States)

Kahn, Frederic J.

2000-04-01

Although analog CRTs continue to enable most of the world's electronic projection displays such as US consumer rear projection televisions, discrete pixel (digital) active matrix LCD and DLP reflective mirror array projectors have rapidly created large nonconsumer markets--primarily for business. Recent advances in image quality, compactness and cost effectiveness of digital projectors have the potential to revolutionize major consumer and entertainment markets as well. Digital penetration of the mainstream consumer projection TV market will begin in the hear 2000. By 2005 digital projection HDTVs could take the major share of the consumer HDTV projection market. Digital projection is expected to dominate both the consumer HDTV and the cinema market by 2010, resulting in potential shipments for all projection markets exceeding 10 M units per year. Digital projection is improving at a rate 10X faster than analog CRT projectors and 5X faster than PDP flat panels. Continued rapid improvement of digital projection is expected due to its relative immaturity and due to the wide diversity of technological improvements being pursued. Key technology enablers are the imaging panels, light sources and micro-optics. Market shares of single panel projectors, MEMs panels, LCOS panels and low T p-Si TFT LCD panel variants are expected to increase.

Full dynamic resolution low lower DA-Converters for flat panel displays

Directory of Open Access Journals (Sweden)

C. Saas

2006-01-01

Full Text Available It has been shown that stepwise charging can reduce the power dissipated in the source drivers of a flat panel display. However the solution presented only provided a dynamic resolution of 3 bits which is not sufficient for obtaining a full color resolution display. In this work a further development of the basic idea is presented. The stepwise charging is increased to 4 bits and supplemented by a current source to provide an output signal which represents an 8 bit value with sufficient accuracy. Within this work the application is an AM-OLED flat panel display, but the concept can easily be applied to other display technologies like TFT-LCD as well.

Fire Resistance of Large-Scale Cross-Laminated Timber Panels

Science.gov (United States)

Henek, Vladan; Venkrbec, Václav; Novotný, Miloslav

2017-12-01

Wooden structures are increasingly being used in the construction of residential buildings. A common and often published reason to avoid wooden structures is their insufficient fire resistance, which reduces bearing capacity. For this reason, composite sandwich structures began to be designed to eliminate this drawback, as well as others. Recently, however, the trend is for a return to the original, wood-only variant and a search is underway for new technical means of improving the properties of such structures. Many timber structure technologies are known, but structures made from cross-laminated timber (CLT) panels have been used very often in recent years. CLT panels, also known as X-LAM, are currently gaining popularity in Europe. In the case of CLT panels composed of several layers of boards, they can be said to offer a certain advantage in that after the surface layer of a board has burnt and the subsurface layer has dried, oxygen is not drawn to the unburned wood for further combustion and thus the burning process ceases. CLT panels do not need to be specially modified or coated with fire resistant materials, although they are usually lined with gypsum-fibre fire resistant boards due to guidelines set out in the relevant standards. This paper presents a new method for the assessment of load-bearing perimeter walls fabricated from CLT panels without the use of an inner fire-retardant lining to ensure fire resistance at the level required by European standards (i.e. those harmonized for the Czech construction industry). The calculations were verified through laboratory tests which show that better parameters can be achieved during the classification of structures from the fire resistance point of view. The aim of the article is to utilize the results of assessment and testing by an accredited laboratory in order to demonstrate the possibilities of using CLT panels for the construction of multistorey as well as multi-purpose buildings in the Czech Republic.

Validated Feasibility Study of Integrally Stiffened Metallic Fuselage Panels for Reducing Manufacturing Costs

Science.gov (United States)

Pettit, R. G.; Wang, J. J.; Toh, C.

2000-01-01

The continual need to reduce airframe cost and the emergence of high speed machining and other manufacturing technologies has brought about a renewed interest in large-scale integral structures for aircraft applications. Applications have been inhibited, however, because of the need to demonstrate damage tolerance, and by cost and manufacturing risks associated with the size and complexity of the parts. The Integral Airframe Structures (IAS) Program identified a feasible integrally stiffened fuselage concept and evaluated performance and manufacturing cost compared to conventional designs. An integral skin/stiffener concept was produced both by plate hog-out and near-net extrusion. Alloys evaluated included 7050-T7451 plate, 7050-T74511 extrusion, 6013-T6511 extrusion, and 7475-T7351 plate. Mechanical properties, structural details, and joint performance were evaluated as well as repair, static compression, and two-bay crack residual strength panels. Crack turning behavior was characterized through panel tests and improved methods for predicting crack turning were developed. Manufacturing cost was evaluated using COSTRAN. A hybrid design, made from high-speed machined extruded frames that are mechanically fastened to high-speed machined plate skin/stringer panels, was identified as the most cost-effective manufacturing solution. Recurring labor and material costs of the hybrid design are up to 61 percent less than the current technology baseline.

78 FR 41937 - Joint Meeting of the Gastroenterology-Urology Panel and the Radiological Devices Panel of the...

Science.gov (United States)

2013-07-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0816] Joint Meeting of the Gastroenterology-Urology Panel and the Radiological Devices Panel of the Medical...: Gastroenterology-Urology Panel and Radiological Devices Panel of the Medical Devices Advisory Committee. General...

On Energy Balance and Production Costs in Tubular and Flat Panel Photobioreactors

NARCIS (Netherlands)

Norsker, N.H.; Barbosa, M.J.; Vermue, M.H.; Wijffels, R.H.

2012-01-01

Reducing mixing in both flat panel and tubular photobioreactors can result in a positive net energy balance with state-of-the-art technology and Dutch weather conditions. In the tubular photobioreactor, the net energy balance becomes positive at velocities <0.3 ms-1, at which point the biomass

A New Targeted CFTR Mutation Panel Based on Next-Generation Sequencing Technology.

Science.gov (United States)

Lucarelli, Marco; Porcaro, Luigi; Biffignandi, Alice; Costantino, Lucy; Giannone, Valentina; Alberti, Luisella; Bruno, Sabina Maria; Corbetta, Carlo; Torresani, Erminio; Colombo, Carla; Seia, Manuela

2017-09-01

Searching for mutations in the cystic fibrosis transmembrane conductance regulator gene (CFTR) is a key step in the diagnosis of and neonatal and carrier screening for cystic fibrosis (CF), and it has implications for prognosis and personalized therapy. The large number of mutations and genetic and phenotypic variability make this search a complex task. Herein, we developed, validated, and tested a laboratory assay for an extended search for mutations in CFTR using a next-generation sequencing-based method, with a panel of 188 CFTR mutations customized for the Italian population. Overall, 1426 dried blood spots from neonatal screening, 402 genomic DNA samples from various origins, and 1138 genomic DNA samples from patients with CF were analyzed. The assay showed excellent analytical and diagnostic operative characteristics. We identified and experimentally validated 159 (of 188) CFTR mutations. The assay achieved detection rates of 95.0% and 95.6% in two large-scale case series of CF patients from central and northern Italy, respectively. These detection rates are among the highest reported so far with a genetic test for CF based on a mutation panel. This assay appears to be well suited for diagnostics, neonatal and carrier screening, and assisted reproduction, and it represents a considerable advantage in CF genetic counseling. Copyright © 2017 American Society for Investigative Pathology and the Association for Molecular Pathology. Published by Elsevier Inc. All rights reserved.

Approaches to Assessing Technological Literacy

Science.gov (United States)

Pearson, Greg

2006-01-01

It is the conclusion of the Committee on Assessing Technological Literacy, a study panel appointed by the National Academy of Engineering and the National Research Council, that very little is known about what children or adults know, can do, and believe about technology. This is because the state of assessment related to technology--or, …

Aeroelastic Uncertainty Quantification Studies Using the S4T Wind Tunnel Model

Science.gov (United States)

Nikbay, Melike; Heeg, Jennifer

2017-01-01

This paper originates from the joint efforts of an aeroelastic study team in the Applied Vehicle Technology Panel from NATO Science and Technology Organization, with the Task Group number AVT-191, titled "Application of Sensitivity Analysis and Uncertainty Quantification to Military Vehicle Design." We present aeroelastic uncertainty quantification studies using the SemiSpan Supersonic Transport wind tunnel model at the NASA Langley Research Center. The aeroelastic study team decided treat both structural and aerodynamic input parameters as uncertain and represent them as samples drawn from statistical distributions, propagating them through aeroelastic analysis frameworks. Uncertainty quantification processes require many function evaluations to asses the impact of variations in numerous parameters on the vehicle characteristics, rapidly increasing the computational time requirement relative to that required to assess a system deterministically. The increased computational time is particularly prohibitive if high-fidelity analyses are employed. As a remedy, the Istanbul Technical University team employed an Euler solver in an aeroelastic analysis framework, and implemented reduced order modeling with Polynomial Chaos Expansion and Proper Orthogonal Decomposition to perform the uncertainty propagation. The NASA team chose to reduce the prohibitive computational time by employing linear solution processes. The NASA team also focused on determining input sample distributions.

76 FR 20720 - Advisory Panel for Integrative Activities; Notice of Meeting

Science.gov (United States)

2011-04-13

... Foundation announces the following meeting: Name: Committee of Visitors Panel for the Experimental Program to Stimulate Competitive Research Science and Technology Centers (STC) 1373. Dates: May 16, 2011; 6 p.m.-8 p.m... materials. Agenda May 16, 2011 6 p.m.-8 p.m. Open Session; Welcome, overview of STC program. May 17, 2011 8...

Use of Internet panels to conduct surveys.

Science.gov (United States)

Hays, Ron D; Liu, Honghu; Kapteyn, Arie

2015-09-01

The use of Internet panels to collect survey data is increasing because it is cost-effective, enables access to large and diverse samples quickly, takes less time than traditional methods to obtain data for analysis, and the standardization of the data collection process makes studies easy to replicate. A variety of probability-based panels have been created, including Telepanel/CentERpanel, Knowledge Networks (now GFK KnowledgePanel), the American Life Panel, the Longitudinal Internet Studies for the Social Sciences panel, and the Understanding America Study panel. Despite the advantage of having a known denominator (sampling frame), the probability-based Internet panels often have low recruitment participation rates, and some have argued that there is little practical difference between opting out of a probability sample and opting into a nonprobability (convenience) Internet panel. This article provides an overview of both probability-based and convenience panels, discussing potential benefits and cautions for each method, and summarizing the approaches used to weight panel respondents in order to better represent the underlying population. Challenges of using Internet panel data are discussed, including false answers, careless responses, giving the same answer repeatedly, getting multiple surveys from the same respondent, and panelists being members of multiple panels. More is to be learned about Internet panels generally and about Web-based data collection, as well as how to evaluate data collected using mobile devices and social-media platforms.

Modification of polymeric materials for 3D printing of external panels of nanosatellites

OpenAIRE

Isaeva Dariya; Simankin Fedor; Doncov Yuriy; Simankin Arkadiy

2017-01-01

The results of mechanical testing of plastic samples, produced by injection molding and 3D printing are shown. Strength properties of filled and non-filled polymers are compared. The applicability of 3D printing technology with filled polymer materials of external panels is evaluated.

At-line validation of a process analytical technology approach for quality control of melamine-urea-formaldehyde resin in composite wood-panel production using near infrared spectroscopy.

Science.gov (United States)

Meder, Roger; Stahl, Wolfgang; Warburton, Paul; Woolley, Sam; Earnshaw, Scott; Haselhofer, Klaus; van Langenberg, Ken; Ebdon, Nick; Mulder, Roger

2017-01-01

The reactivity of melamine-urea-formaldehyde resins is of key importance in the manufacture of engineered wood products such as medium density fibreboard (MDF) and other wood composite products. Often the MDF manufacturing plant has little available information on the resin reactivity other than details of the resin specification at the time of batch manufacture, which often occurs off-site at a third-party resin plant. Often too, fresh resin on delivery at the MDF plant is mixed with variable volume of aged resin in storage tanks, thereby rendering any specification of the fresh resin batch obsolete. It is therefore highly desirable to develop a real-time, at-line or on-line, process analytical technology to monitor the quality of the resin prior to MDF panel manufacture. Near infrared (NIR) spectroscopy has been calibrated against standard quality methods and against 13 C nuclear magnetic resonance (NMR) measures of molecular composition in order to provide at-line process analytical technology (PAT), to monitor the resin quality, particularly the formaldehyde content of the resin. At-line determination of formaldehyde content in the resin was made possible using a six-factor calibration with an R 2 (cal) value of 0.973, and R 2 (CV) value of 0.929 and a root-mean-square error of cross-validation of 0.01. This calibration was then used to generate control charts of formaldehyde content at regular four-hourly periods during MDF panel manufacture in a commercial MDF manufacturing plant.

Micro-inverter solar panel mounting

Science.gov (United States)

Morris, John; Gilchrist, Phillip Charles

2016-02-02

Processes, systems, devices, and articles of manufacture are provided. Each may include adapting micro-inverters initially configured for frame-mounting to mounting on a frameless solar panel. This securement may include using an adaptive clamp or several adaptive clamps secured to a micro-inverter or its components, and using compressive forces applied directly to the solar panel to secure the adaptive clamp and the components to the solar panel. The clamps can also include compressive spacers and safeties for managing the compressive forces exerted on the solar panels. Friction zones may also be used for managing slipping between the clamp and the solar panel during or after installation. Adjustments to the clamps may be carried out through various means and by changing the physical size of the clamps themselves.

1994 Panel 1 Utilization Plan

International Nuclear Information System (INIS)

1994-01-01

The Waste Isolation Pilot Plant (WIPP) is intended to receive, handle, and permanently dispose of transuranic (TRU) waste. To fulfill this mission, the U.S. Department of Energy (DOE) constructed a full-scale facility to demonstrate both technical and operational principles of the permanent isolation of TRU waste. The WIPP consists of surface and underground facilities. Panel 1 is situated in the underground facility horizon which is located approximately 2,150 feet below the surface in the predominantly halite Salado Formation. The Panel 1 Utilization Plan provides a strategy for the optimum use of Panel 1 which is consistent with the priorities established by the DOE to accomplish the WIPP mission. These priorities, which include maintaining personnel safety, conducting performance assessment, and continued operational enhancements, are the guiding premise for the decisions on the planned usage of the WIPP underground facility. The continuation of ongoing investigations along with the planned testing and training to be carried out in Panel 1 will enhance the current knowledge and understanding of the operational and geotechnical aspects of the panel configuration. This enhancement will ultimately lead to safer, more efficient, and more cost-effective methods of operation. Excavation of the waste storage area began in May 1986 with the mining of entries to Panel 1. The original design for the waste storage rooms at the WIPP provided a limited period of time during which to mine the openings and to emplace waste. Each panel, consisting of seven storage rooms, was scheduled to be mined and filled in less than 5 years. Panel 1 was developed to receive waste for a demonstration phase that was scheduled to start in October 1988. The demonstration phase was deferred, and the experimental test program was modified to use contact-handled (CH) transuranic waste in bin-scale tests, planned for Room 1, Panel 1

Technologies for propelled hypersonic flight: Technologies des vols hypersoniques propulsés

National Research Council Canada - National Science Library

2006-01-01

These reports document the results of the Applied Vehicle Technology Panel Working Group 10, Subgroups 1, 2, and 3, who aimed to address selected critical issues related to propelled hypersonic flight...

Data quality in probability-based online panels: Nonresponse, attrition, and panel conditioning

NARCIS (Netherlands)

Struminskaya, B.; Methodology and statistics for the behavioural and social sciences

2014-01-01

Online panels – surveys administered over the Internet in which persons are asked to complete surveys regularly – offer cost reductions compared to surveys that use more traditional modes of data collection (face-to-face, telephone, and mail). However, some characteristics of online panels may cause

77 FR 24227 - Proposal Review Panel for Social and Economic Sciences; Notice of Meeting

Science.gov (United States)

2012-04-23

... NATIONAL SCIENCE FOUNDATION Proposal Review Panel for Social and Economic Sciences; Notice of... Engineering Center (NSEC) at Arizona State University by the Division Social and Economic Sciences ( 10748... Kronz, Program Director; Science, Technology and Society Program; Division of Social and Economic...

Solar panel truss mounting systems and methods

Energy Technology Data Exchange (ETDEWEB)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2016-06-28

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

Solar panel truss mounting systems and methods

Energy Technology Data Exchange (ETDEWEB)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2018-01-30

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

Solar panel truss mounting systems and methods

Science.gov (United States)

Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

2015-10-20

An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

High-performance flat-panel solar thermoelectric generators with high thermal concentration

Science.gov (United States)

Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J. Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

2011-07-01

The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m-2) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity.

High-performance flat-panel solar thermoelectric generators with high thermal concentration.

Science.gov (United States)

Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

2011-05-01

The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m(-2)) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity. © 2011 Macmillan Publishers Limited. All rights reserved

Graphite/epoxy orthogrid panel fabrication

Science.gov (United States)

Lager, J. R.

1978-01-01

The structural concept considered for a spacecraft body structure is a grid stiffened skin with a skin laminate configuration and the stiffener grid geometry selected to best suit the design requirements. The orthogrid panel developed weighs 0.55 lb/sq ft and resisted an ultimate in-plane shear load of 545 lbf/in. The basic concept of a grid stiffener composite panel is that a relatively thin skin is reinforced with a gridwork of stiffeners so that the overall panel can resist design loads without becoming structurally unstable or being overstressed. The main feature of the orthogrid panel design is that it provides the potential for low cost structural panels when advanced to the production phase. The most innovative part of the fabrication method is the foam/fiberglass stiffener web grid billet fabrication and machining to size.

Modification of polymeric materials for 3D printing of external panels of nanosatellites

Directory of Open Access Journals (Sweden)

Isaeva Dariya

2017-01-01

Full Text Available The results of mechanical testing of plastic samples, produced by injection molding and 3D printing are shown. Strength properties of filled and non-filled polymers are compared. The applicability of 3D printing technology with filled polymer materials of external panels is evaluated.

Acoustically Tailored Composite Rotorcraft Fuselage Panels

Science.gov (United States)

Hambric, Stephen; Shepherd, Micah; Koudela, Kevin; Wess, Denis; Snider, Royce; May, Carl; Kendrick, Phil; Lee, Edward; Cai, Liang-Wu

2015-01-01

A rotorcraft roof sandwich panel has been redesigned to optimize sound power transmission loss (TL) and minimize structure-borne sound for frequencies between 1 and 4 kHz where gear meshing noise from the transmission has the most impact on speech intelligibility. The roof section, framed by a grid of ribs, was originally constructed of a single honeycomb core/composite face sheet panel. The original panel has coincidence frequencies near 700 Hz, leading to poor TL across the frequency range of 1 to 4 kHz. To quiet the panel, the cross section was split into two thinner sandwich subpanels separated by an air gap. The air gap was sized to target the fundamental mass-spring-mass resonance of the double panel system to less than 500 Hz. The panels were designed to withstand structural loading from normal rotorcraft operation, as well as 'man-on-the-roof' static loads experienced during maintenance operations. Thin layers of VHB 9469 viscoelastomer from 3M were also included in the face sheet ply layups, increasing panel damping loss factors from about 0.01 to 0.05. Measurements in the NASA SALT facility show the optimized panel provides 6-11 dB of acoustic transmission loss improvement, and 6-15 dB of structure-borne sound reduction at critical rotorcraft transmission tonal frequencies. Analytic panel TL theory simulates the measured performance quite well. Detailed finite element/boundary element modeling of the baseline panel simulates TL slightly more accurately, and also simulates structure-borne sound well.

Anestesia venosa total (AVT em lactente com doença de Werdnig-Hoffmann: relato de caso Anestesia venosa total (AVT en lactante con enfermedad de Werdnig-Hoffmann: relato de caso Total intravenous anesthesia (TIVA in an infant with Werdnig-Hoffmann disease: case report

Directory of Open Access Journals (Sweden)

Luis Otavio Esteves

2010-10-01

Full Text Available Foi com grande interesse que li o artigo "Anestesia Venosa Total (AVT em Lactente com Doença de Werdnig-Hoffmann. Relato de Caso", de Resende e col. ¹, publicado nesta revista. Gostaria, em primeiro lugar, de parabenizar os autores pela iniciativa. Entretanto, dois pontos me chamaram a atenção. O primeiro refere-se à definição de lactente, a qual compreende o período de 1 a 12 meses de idade. A partir de 12 meses, define-se como pré-escolar ou apenas criança. No artigo, o autor coloca a idade do paciente como 1 ano, mas não especifica meses ou dias. Provavelmente, esse paciente tem mais de 12 meses, sendo, dessa forma, a definição de lactente inadequada. O segundo e mais importante ponto diz respeito à técnica usada e ao título do artigo. No título, utilizou-se a expressão "anestesia venosa total", mas no relato foi dito que, além de propofol e remifentanil, a anestesia foi mantida com oxigênio e N2O. Se foi usado um gás com propriedades anestésicas (N2O, não seria correto classificar essa técnica como venosa total. Além disso, ele cita o artigo de Crawford e col. ², que definiu doses de remifentanil para intubação em crianças. Esse estudo foi realizado utilizando-se oxigenação na concentração de 100%, pois os autores provavelmente entendem que a adição de gases com propriedades anestésicas interferiria nos resultados obtidosFue con un gran interés que leí el artículo "Anestesia Venosa Total (AVT en Lactante con Enfermedad de Werdnig-Hoffmann. Relato de Caso", de Resende y col. ¹, publicado en esta revista. Y de hecho quiero, en primer lugar, felicitar a los autores por la iniciativa. Sin embargo, dos puntos me llamaron la atención. El primero, se refiere a la definición de lactante, la cual abarca el período de 1 a 12 meses de edad. A partir de los 12 meses, se define como preescolar o apenas como niño. En el artículo, el autor coloca la edad del paciente como de 1 año, pero no especifica meses o d

Solar-Panel Dust Accumulation and Cleanings

Science.gov (United States)

2005-01-01

Air-fall dust accumulates on the solar panels of NASA's Mars Exploration Rovers, reducing the amount of sunlight reaching the solar arrays. Pre-launch models predicted steady dust accumulation. However, the rovers have been blessed with occasional wind events that clear significant amounts of dust from the solar panels. This graph shows the effects of those panel-cleaning events on the amount of electricity generated by Spirit's solar panels. The horizontal scale is the number of Martian days (sols) after Spirit's Jan. 4, 2005, (Universal Time) landing on Mars. The vertical scale indicates output from the rover's solar panels as a fraction of the amount produced when the clean panels first opened. Note that the gradual declines are interrupted by occasional sharp increases, such as a dust-cleaning event on sol 420.

Vasotocin has the potential to inhibit basolateral Na(+)/K (+)-pump current across isolated skin of tree frog in vitro, via its V(2)-type receptor/cAMP pathway.

Science.gov (United States)

Takada, Makoto; Fujimaki, Kayo; Hokari, Shigeru

2008-11-01

Adult frog skin transports Na(+) from the apical to the basolateral side across the skin. Antidiuretic hormone (ADH) is involved in the regulation of Na(+) transport in both mammals and amphibians. We investigated the effect of arginine vasotocin (AVT), the ADH of amphibians, on the short-circuit current (SCC) across intact skin and on the basolateral Na(+)/K(+)-pump current across apically nystatin-permeabilized skin of the tree frog, Hyla japonica, in which the V(2)-type ADH receptor is expressed in vitro. In intact skin, 1 pM AVT had no effect on the SCC, but 10 nM AVT was sufficient to stimulate the SCC since 10 nM and 1 microM of AVT increased the SCC 3.2- and 3.4-fold, respectively (P > 0.9). However, in permeabilized skin, AVT (1 microM) decreased the Na(+)/K(+)-pump current to 0.79 times vehicle control. Similarly, 500 microM of 8Br-cAMP increased the SCC 3.2-fold, yet 1 mM of 8Br-cAMP decreased the Na(+)/K(+)-pump current to 0.76 times vehicle control. Arachidonic acid (10(-5) M) tended to decrease the Na(+)/K(+)-pump current. To judge from these in vitro experiments, AVT has the potential to inhibit the basolateral Na(+)/K(+)-pump current via the V(2)-type receptor/cAMP pathway in the skin of the tree frog.

Electrical design for origami solar panels and a small spacecraft test mission

Science.gov (United States)

Drewelow, James; Straub, Jeremy

2017-05-01

Efficient power generation is crucial to the design of spacecraft. Mass, volume, and other limitations prevent the use of traditional spacecraft support structures from being suitable for the size of solar array required for some missions. Folding solar panel / panel array systems, however, present a number of design challenges. This paper considers the electrical design of an origami system. Specifically, it considers how to provide low impedance, durable channels for the generated power and the electrical aspects of the deployment system and procedure. The ability to dynamically reconfigure the electrical configuration of the solar cells is also discussed. Finally, a small satellite test mission to demonstrate the technology is proposed, before concluding.

Panel fabrication utilizing GaAs solar cells

Science.gov (United States)

Mardesich, N.

1984-01-01

The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

Attic Retrofits Using Nail-Base Insulated Panels

Energy Technology Data Exchange (ETDEWEB)

Mallay, David [Home Innovation Research Labs; Kochkin, Vladimir [Home Innovation Research Labs

2018-03-26

This project developed and demonstrated a roof/attic energy retrofit solution using nail-base insulated panels for existing homes where traditional attic insulation approaches are not effective or feasible. Nail-base insulated panels (retrofit panels) consist of rigid foam insulation laminated to one face of a wood structural panel. The prefabricated panels are installed above the existing roof deck during a reroofing effort.

Analysing sensory panel performance in a proficiency test using the PanelCheck software

DEFF Research Database (Denmark)

Tomic, O.; Luciano, G.; Nilsen, A.

2010-01-01

Check software, a workflow is proposed that guides the user through the data analysis process. This allows practitioners and non-statisticians to get an overview over panel performances in a rapid manner without the need to be familiar with details on the statistical methods. Visualisation of data analysis...... results plays an important role as this provides a time saving and efficient way of screening and investigating sensory panel performances. Most of the statistical methods used in this paper are available in the open source software PanelCheck, which may be downloaded and used for free....

Broadband transmission noise reduction of smart panels featuring piezoelectric shunt circuits and sound-absorbing material.

Science.gov (United States)

Kim, Jaehwan; Lee, Joong-Kuen

2002-09-01

The possibility of a broadband noise reduction of piezoelectric smart panels is experimentally studied. A piezoelectric smart panel is basically a plate structure on which piezoelectric patches with electrical shunt circuits are mounted and sound-absorbing material is bonded on the surface of the structure. Sound-absorbing material can absorb the sound transmitted at the midfrequency region effectively while the use of piezoelectric shunt damping can reduce the transmission at resonance frequencies of the panel structure. To be able to reduce the sound transmission at low panel resonance frequencies, piezoelectric damping using the measured electrical impedance model is adopted. A resonant shunt circuit for piezoelectric shunt damping is composed of resistor and inductor in series, and they are determined by maximizing the dissipated energy through the circuit. The transmitted noise-reduction performance of smart panels is tested in an acoustic tunnel. The tunnel is a square cross-sectional tube and a loudspeaker is mounted at one side of the tube as a sound source. Panels are mounted in the middle of the tunnel and the transmitted sound pressure across panels is measured. When an absorbing material is bonded on a single plate, a remarkable transmitted noise reduction in the midfrequency region is observed except for the fundamental resonance frequency of the plate. By enabling the piezoelectric shunt damping, noise reduction is achieved at the resonance frequency as well. Piezoelectric smart panels incorporating passive absorbing material and piezoelectric shunt damping is a promising technology for noise reduction over a broadband of frequencies.

High energy physics advisory panel's composite subpanel for the assessment of the status of accelerator physics and technology

International Nuclear Information System (INIS)

1996-05-01

In November 1994, Dr. Martha Krebs, Director of the US Department of Energy (DOE) Office of Energy Research (OER), initiated a broad assessment of the current status and promise of the field of accelerator physics and technology with respect to five OER programs -- High Energy Physics, Nuclear Physics, Basic Energy Sciences, Fusion Energy, and Health and Environmental Research. Dr. Krebs asked the High Energy Physics Advisory Panel (HEPAP) to establish a composite subpanel with representation from the five OER advisory committees and with a balance of membership drawn broadly from both the accelerator community and from those scientific disciplines associated with the OER programs. The Subpanel was also charged to provide recommendations and guidance on appropriate future research and development needs, management issues, and funding requirements. The Subpanel finds that accelerator science and technology is a vital and intellectually exciting field. It has provided essential capabilities for the DOE/OER research programs with an enormous impact on the nation's scientific research, and it has significantly enhanced the nation's biomedical and industrial capabilities. Further progress in this field promises to open new possibilities for the scientific goals of the OER programs and to further benefit the nation. Sustained support of forefront accelerator research and development by the DOE's OER programs and the DOE's predecessor agencies has been responsible for much of this impact on research. This report documents these contributions to the DOE energy research mission and to the nation

Mounting clips for panel installation

Science.gov (United States)

Cavieres, Andres; Al-Haddad, Tristan; Goodman, Joseph; Valdes, Francisco

2017-02-14

An exemplary mounting clip for removably attaching panels to a supporting structure comprises a base, spring locking clips, a lateral flange, a lever flange, and a spring bonding pad. The spring locking clips extend upwardly from the base. The lateral flange extends upwardly from a first side of the base. The lateral flange comprises a slot having an opening configured to receive at least a portion of one of the one or more panels. The lever flange extends outwardly from the lateral flange. The spring bonding flange extends downwardly from the lever flange. At least a portion of the first spring bonding flange comprises a serrated edge for gouging at least a portion of the one or more panels when the one or more panels are attached to the mounting clip to electrically and mechanically couple the one or more panels to the mounting clip.

Projection display technology for avionics applications

Science.gov (United States)

Kalmanash, Michael H.; Tompkins, Richard D.

2000-08-01

Avionics displays often require custom image sources tailored to demanding program needs. Flat panel devices are attractive for cockpit installations, however recent history has shown that it is not possible to sustain a business manufacturing custom flat panels in small volume specialty runs. As the number of suppliers willing to undertake this effort shrinks, avionics programs unable to utilize commercial-off-the-shelf (COTS) flat panels are placed in serious jeopardy. Rear projection technology offers a new paradigm, enabling compact systems to be tailored to specific platform needs while using a complement of COTS components. Projection displays enable improved performance, lower cost and shorter development cycles based on inter-program commonality and the wide use of commercial components. This paper reviews the promise and challenges of projection technology and provides an overview of Kaiser Electronics' efforts in developing advanced avionics displays using this approach.

ALDS 1978 panel review. [PNL

Energy Technology Data Exchange (ETDEWEB)

Hall, D.L. (ed.)

1979-08-01

Pacific Northwest Laboratory (PNL) is examining the analysis of large data sets (ALDS). After one year's work, a panel was convened to evaluate the project. This document is the permanent record of that panel review. It consists of edited transcripts of presentations made to the panel by the PNL staff, a summary of the responses of the panel to these presentations, and PNL's plans for the development of the ALDS project. The representations of the PNL staff described various aspects of the project and/or the philosophy surrounding the project. Supporting materials appear in appendixes. 20 figures, 4 tables. (RWR)

Energy consumption and income. A semiparametric panel data analysis

Energy Technology Data Exchange (ETDEWEB)

Nguyen-Van, Phu [BETA, CNRS and Universite de Strasbourg, 61 avenue de la Foret Noire, F-67085 Strasbourg (France)

2010-05-15

This paper proposes a semiparametric analysis for the study of the relationship between energy consumption per capita and income per capita for an international panel dataset. It shows little evidence for the existence of an environmental Kuznets curve for energy consumption. Energy consumption increases with income for a majority of countries and then stabilizes for very high income countries. Neither changes in energy structure nor macroeconomic cycle/technological change have significant effect on energy consumption. (author)

12 Layout ppp2

African Journals Online (AJOL)

Nubidga

shows that only two schools of higher learning in the country teach AVT and that, 42 studies so far have been carried ..... English and French as official languages, alongside. 286 national ..... The government should create or activate an AVT.

MO-E-BRB-02: Panel Member

Energy Technology Data Exchange (ETDEWEB)

Larner, J. [University of Virginia (United States)

2016-06-15

In this interactive session, lung SBRT patient cases will be presented to highlight real-world considerations for ensuring safe and accurate treatment delivery. An expert panel of speakers will discuss challenges specific to lung SBRT including patient selection, patient immobilization techniques, 4D CT simulation and respiratory motion management, target delineation for treatment planning, online treatment alignment, and established prescription regimens and OAR dose limits. Practical examples of cases, including the patient flow thought the clinical process are presented and audience participation will be encouraged. This panel session is designed to provide case demonstration and review for lung SBRT in terms of (1) clinical appropriateness in patient selection, (2) strategies for simulation, including 4D and respiratory motion management, and (3) applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent, and (4) image guidance in treatment delivery. Learning Objectives: Understand the established requirements for patient selection in lung SBRT Become familiar with the various immobilization strategies for lung SBRT, including technology for respiratory motion management Understand the benefits and pitfalls of applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent determination for lung SBRT Understand established prescription regimes and OAR dose limits.

MO-E-BRB-03: Panel Member

Energy Technology Data Exchange (ETDEWEB)

Salter, B. [University Utah (United States)

2016-06-15

In this interactive session, lung SBRT patient cases will be presented to highlight real-world considerations for ensuring safe and accurate treatment delivery. An expert panel of speakers will discuss challenges specific to lung SBRT including patient selection, patient immobilization techniques, 4D CT simulation and respiratory motion management, target delineation for treatment planning, online treatment alignment, and established prescription regimens and OAR dose limits. Practical examples of cases, including the patient flow thought the clinical process are presented and audience participation will be encouraged. This panel session is designed to provide case demonstration and review for lung SBRT in terms of (1) clinical appropriateness in patient selection, (2) strategies for simulation, including 4D and respiratory motion management, and (3) applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent, and (4) image guidance in treatment delivery. Learning Objectives: Understand the established requirements for patient selection in lung SBRT Become familiar with the various immobilization strategies for lung SBRT, including technology for respiratory motion management Understand the benefits and pitfalls of applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent determination for lung SBRT Understand established prescription regimes and OAR dose limits.

MO-E-BRB-01: Panel Member

Energy Technology Data Exchange (ETDEWEB)

Benedict, S. [University of California Davis Medical Center (United States)

2016-06-15

In this interactive session, lung SBRT patient cases will be presented to highlight real-world considerations for ensuring safe and accurate treatment delivery. An expert panel of speakers will discuss challenges specific to lung SBRT including patient selection, patient immobilization techniques, 4D CT simulation and respiratory motion management, target delineation for treatment planning, online treatment alignment, and established prescription regimens and OAR dose limits. Practical examples of cases, including the patient flow thought the clinical process are presented and audience participation will be encouraged. This panel session is designed to provide case demonstration and review for lung SBRT in terms of (1) clinical appropriateness in patient selection, (2) strategies for simulation, including 4D and respiratory motion management, and (3) applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent, and (4) image guidance in treatment delivery. Learning Objectives: Understand the established requirements for patient selection in lung SBRT Become familiar with the various immobilization strategies for lung SBRT, including technology for respiratory motion management Understand the benefits and pitfalls of applying multi imaging modality (4D CT imaging, MRI, PET) for tumor volume delineation and motion extent determination for lung SBRT Understand established prescription regimes and OAR dose limits.

Thermal energy storage in the form of heat or cold with using of the PCM-based accumulation panels

Directory of Open Access Journals (Sweden)

Skovajsa Jan

2016-01-01

Full Text Available This article describes the usage of thermal energy storage in the form of heat and cold with an adaptation of the special device which is composed of the thermal panels. These panels are based on the phase change materials (PCM for normal inner environment temperature in buildings. The energy for the thermal energy storage is possible to get from built-in electric heating foil or from the tube heat exchanger, which is build in the thermal panels. This technology is able to use renewable energy sources, for example, solar thermal collectors and air-to-water heat pump as a source of heat for heating of the hot water tank. In the cooling mode, there is able to use the heat pump or photovoltaics panels in combination with thermoelectric coolers for cooling.

Heat Conductivity Resistance of Concrete Wall Panel by Water Flowing in Different Orientations of Internal PVC pipe

Science.gov (United States)

Umi, N. N.; Norazman, M. N.; Daud, N. M.; Yusof, M. A.; Yahya, M. A.; Othman, M.

2018-04-01

Green building technology and sustainability development is current focus in the world nowadays. In Malaysia and most tropical countries the maximum temperature recorded typically at 35°C. Air-conditioning system has become a necessity in occupied buildings, thereby increasing the cost of electric consumption. The aim of this study is to find out the solution in minimizing heat transfer from the external environment and intentions towards going green. In this study, the experimental work includes testing three types of concrete wall panels. The main heat intervention material in this research is 2 inch diameter Polyvinyl Chloride (PVC) pipe embedded at the center of the concrete wall panel, while the EPS foam beads were added to the cement content in the concrete mix forming the outer layer of the wall panel. Water from the rainwater harvesting system is regulated in the PVC pipe to intervene with the heat conductivity through the wall panel. Results from the experimental works show that the internal surface temperature of these heat resistance wall panels is to 3□C lower than control wall panel from plain interlocking bricks.

Panel acoustic contribution analysis.

Science.gov (United States)

Wu, Sean F; Natarajan, Logesh Kumar

2013-02-01

Formulations are derived to analyze the relative panel acoustic contributions of a vibrating structure. The essence of this analysis is to correlate the acoustic power flow from each panel to the radiated acoustic pressure at any field point. The acoustic power is obtained by integrating the normal component of the surface acoustic intensity, which is the product of the surface acoustic pressure and normal surface velocity reconstructed by using the Helmholtz equation least squares based nearfield acoustical holography, over each panel. The significance of this methodology is that it enables one to analyze and rank relative acoustic contributions of individual panels of a complex vibrating structure to acoustic radiation anywhere in the field based on a single set of the acoustic pressures measured in the near field. Moreover, this approach is valid for both interior and exterior regions. Examples of using this method to analyze and rank the relative acoustic contributions of a scaled vehicle cabin are demonstrated.

New directions in fusion machines: report on the MFAC Panel X on high power density options

International Nuclear Information System (INIS)

Linford, R.K.

1985-01-01

The high cost of fusion is motivating a shift in research interest toward smaller, lower-cost systems. Panel X of the Magnetic Fusion Advisory Committee (MFAC) was charged to assess the potential benefits and problems associated with small, high-power-density approaches to fusion. The Panel identified figures of merit which are useful in evaluating various approaches to reduce the development costs and capital costs of fusion systems. As a result of their deliberations, the Panel recommended that ''...increased emphasis should be given to improving the mass power density of fusion systems, aiming at a minimum target of 100 kWe/tonne'', and that ''Increased emphasis should be given to concepts that offer the potential to reduce substantially the cost of development steps in physics and technology.''

New directions in fusion machines: Report on the MFAC panel X on high power density options

International Nuclear Information System (INIS)

Linford, R.K.

1986-01-01

The high cost of fusion is motivating a shift in research interest toward smaller, lower-cost systems. Panel X of the Magnetic Fusion Advisory Committee (MFAC) was charged to assess the potential benefits and problems associated with small, highpower-density approaches to fusion. The Panel identified figures of merit which are useful in evaluating various approaches to reduce the development costs and capital costs of fusion systems. As a result of their deliberations, the Panel recommended that ''...increased emphasis should be given to improving the mass power density of fusion systems, aiming at a minimum target of 100 kWe/tonne'', and that ''Increased emphasis should be given to concepts that offer the potential to reduce4 substantially the cost of development steps in physics and technology.''

Inclusion of Population-specific Reference Panel from India to the 1000 Genomes Phase 3 Panel Improves Imputation Accuracy.

Science.gov (United States)

Ahmad, Meraj; Sinha, Anubhav; Ghosh, Sreya; Kumar, Vikrant; Davila, Sonia; Yajnik, Chittaranjan S; Chandak, Giriraj R

2017-07-27

Imputation is a computational method based on the principle of haplotype sharing allowing enrichment of genome-wide association study datasets. It depends on the haplotype structure of the population and density of the genotype data. The 1000 Genomes Project led to the generation of imputation reference panels which have been used globally. However, recent studies have shown that population-specific panels provide better enrichment of genome-wide variants. We compared the imputation accuracy using 1000 Genomes phase 3 reference panel and a panel generated from genome-wide data on 407 individuals from Western India (WIP). The concordance of imputed variants was cross-checked with next-generation re-sequencing data on a subset of genomic regions. Further, using the genome-wide data from 1880 individuals, we demonstrate that WIP works better than the 1000 Genomes phase 3 panel and when merged with it, significantly improves the imputation accuracy throughout the minor allele frequency range. We also show that imputation using only South Asian component of the 1000 Genomes phase 3 panel works as good as the merged panel, making it computationally less intensive job. Thus, our study stresses that imputation accuracy using 1000 Genomes phase 3 panel can be further improved by including population-specific reference panels from South Asia.

Honeycomb metal panel

International Nuclear Information System (INIS)

1979-01-01

Product constituted by a honeycomb metal panel that can be employed to advantage for manufacturing lagging by sandwiching it between two plane sheets, utilized in particular in the nuclear industry where lagging has to have a very long life strength. The honeycomb metal panel is made of an expanded metal extrusion previously cut so as to form, after additional drawing, a honeycomb structure with square or rectangular cells with a plane surface [fr

Exascale Workshop Panel Report Meeting

Energy Technology Data Exchange (ETDEWEB)

Khaleel, Mohammad A.

2010-07-01

The Exascale Review Panel consists of 12 scientists and engineers with experience in various aspects of high-performance computing and its application, development, and management. The Panel hear presentations by several representatives of the workshops and town meetings convened over the past few years to examine the need for exascale computation capability and the justification for a U.S. Department of Energy (DOE) program to develop such capability. This report summarizes information provided by the presenters and substantial written reports to the Panel in advance of the meeting in Washington D.C. on January 19-20, 2010. The report also summarizes the Panel's conclusions with regard to the justification of a DOE-led exascale initiative.

Landfill waste and recycling: Use of a screening-level risk assessment tool for end-of-life cadmium telluride (CdTe) thin-film photovoltaic (PV) panels

International Nuclear Information System (INIS)

Cyrs, William D.; Avens, Heather J.; Capshaw, Zachary A.; Kingsbury, Robert A.; Sahmel, Jennifer; Tvermoes, Brooke E.

2014-01-01

Grid-connected solar photovoltaic (PV) power is currently one of the fastest growing power-generation technologies in the world. While PV technologies provide the environmental benefit of zero emissions during use, the use of heavy metals in thin-film PV cells raises important health and environmental concerns regarding the end-of-life disposal of PV panels. To date, there is no published quantitative assessment of the potential human health risk due to cadmium leaching from cadmium telluride (CdTe) PV panels disposed in a landfill. Thus, we used a screening-level risk assessment tool to estimate possible human health risk associated with disposal of CdTe panels into landfills. In addition, we conducted a literature review of potential cadmium release from the recycling process in order to contrast the potential health risks from PV panel disposal in landfills to those from PV panel recycling. Based on the results of our literature review, a meaningful risk comparison cannot be performed at this time. Based on the human health risk estimates generated for PV panel disposal, our assessment indicated that landfill disposal of CdTe panels does not pose a human health hazard at current production volumes, although our results pointed to the importance of CdTe PV panel end-of-life management. - Highlights: • Analysis of possible human health risk posed by disposal of CdTe panels into landfills. • Qualitative comparison of risks associated with landfill disposal and recycling of CdTe panels. • Landfill disposal of CdTe panels does not pose a human health hazard at current production volumes. • There could be potential risks associated with recycling if not properly managed. • Factors other than concerns over toxic substances will likely drive the decisions of how to manage end-of-life PV panels

Promoting business and entrepreneurial awareness in health care professionals: lessons from venture capital panels at medicine 2.0 conferences.

Science.gov (United States)

Miron-Shatz, Talya; Shatz, Itamar; Becker, Stefan; Patel, Jigar; Eysenbach, Gunther

2014-08-06

There are few mechanisms that bring the academic and business worlds together in a way that would maximize the success of health technology (health tech) start-ups by increasing researchers' knowledge about how to operate in the business world. Existing solutions (eg, technology transfer offices and dual degree MD/MBA programs) are often unavailable to researchers from outside the institution or to those who have already completed their primary education, such as practicing physicians. This paper explores current solutions and offers a partial solution: include venture capital (VC) panels in medical conferences. These VC panels educate academics on 2 important and interconnected issues: how to "pitch" their ideas in the business world and what to consider when creating a company. In these sessions, academia-based start-up companies present their ideas before a VC panel composed of professional investors and receive feedback on their idea, business plan, and presentation techniques. Recent panel recommendations from Medicine 2.0 conferences fell into 7 categories: (1) the product, service, or idea you are developing into a company, (2) determine market forces and identify the target audience, (3) describe your competitive advantage, (4) the business plan, (5) current and future resources and capabilities, (6) legal aspects, and (7) general advice on the art of pitching. The academic and business literature validates many of these recommendations suggesting that VC panels may be a viable and cost-effective introduction to business and entrepreneurial education for physicians and other health care professionals. Panels benefit not only the presenting companies, but also the physicians, psychologists, and other health care professionals attending the session. Incorporating VC panels into academic conferences might also illuminate the need for incorporating relevant business training within academia.

Promoting Business and Entrepreneurial Awareness in Health Care Professionals: Lessons From Venture Capital Panels at Medicine 2.0 Conferences

Science.gov (United States)

Patel, Jigar; Eysenbach, Gunther

2014-01-01

There are few mechanisms that bring the academic and business worlds together in a way that would maximize the success of health technology (health tech) start-ups by increasing researchers’ knowledge about how to operate in the business world. Existing solutions (eg, technology transfer offices and dual degree MD/MBA programs) are often unavailable to researchers from outside the institution or to those who have already completed their primary education, such as practicing physicians. This paper explores current solutions and offers a partial solution: include venture capital (VC) panels in medical conferences. These VC panels educate academics on 2 important and interconnected issues: how to “pitch” their ideas in the business world and what to consider when creating a company. In these sessions, academia-based start-up companies present their ideas before a VC panel composed of professional investors and receive feedback on their idea, business plan, and presentation techniques. Recent panel recommendations from Medicine 2.0 conferences fell into 7 categories: (1) the product, service, or idea you are developing into a company, (2) determine market forces and identify the target audience, (3) describe your competitive advantage, (4) the business plan, (5) current and future resources and capabilities, (6) legal aspects, and (7) general advice on the art of pitching. The academic and business literature validates many of these recommendations suggesting that VC panels may be a viable and cost-effective introduction to business and entrepreneurial education for physicians and other health care professionals. Panels benefit not only the presenting companies, but also the physicians, psychologists, and other health care professionals attending the session. Incorporating VC panels into academic conferences might also illuminate the need for incorporating relevant business training within academia. PMID:25100579

Real scale experimental study for performance evaluation of unidirectional air diffuser perforated panels

Science.gov (United States)

Tăcutu, Laurenţiu; Nastase, Ilinca; Iordache, Vlad; Catalina, Tiberiu; Croitoru, Cristiana Verona

2018-02-01

Nowadays, there is an increasing emphasis on indoor air quality due to technological evolution and the fact that people spend most of the time in enclosed spaces. Also, energy efficiency is another related factor that gains more and more attention. Improving air distribution in an enclosure can lead to achieve these goals. This improvement can be done by adjustingthe air terminals position, theredimensions or the air diffuser perforations. The paper presents the study of 8 types of panels with different perforations shapes. The systems were characterized by flow, pressure loss and noise. Usualand special geometries were chosen, all having the same flowsurface. The perforated panels were mounted in a unidirectional air flow (UAF)diffuser, also called a laminar air flow (LAF)diffuser, that is placed in a real scale operating room (OR) in our laboratory.The purpose of this study is to determine whether changing the shape in the perforated panels can improve the technical parameters of the diffuser.

Technology and skill demand in Mexico

OpenAIRE

Lopez-Acevedo, Gladys

2002-01-01

The author investigates the effects of technology on the employment and wages of differently skilled Mexican manufacturing workers using firm panel data from 1992-99. She analyzes the relationship between technology and skill demand. Findings support the skill-biased technical change hypothesis. She then examines the temporal relationship of technology adoption to firm productivity and wor...

Application of water flowing PVC pipe and EPS foam bead as insulation for wall panel

Science.gov (United States)

Ali, Umi Nadiah; Nor, Norazman Mohamad; Yusuf, Mohammed Alias; Othman, Maidiana; Yahya, Muhamad Azani

2018-02-01

Malaysia located in tropical climate which have a typical temperature range between 21 °C to 36 °C. Due to this, air-conditioning system for buildings become a necessity to provide comfort to occupants. In order to reduce the energy consumption of the air-conditioning system, the transmission of heat from outdoor to indoor space should be kept as minimum as possible. This article discuss about a technology to resist heat transfer through concrete wall panel using a hybrid method. In this research, PVC pipe was embedded at the center of concrete wall panel while the EPS foam beads were added about 1% of the cement content in the concrete mix forming the outer layer of the wall panel. Water is regulated in the PVC pipe from the rainwater harvesting system. The aim of this study is to minimize heat transfer from the external environment into the building. Internal building temperature which indicated in BS EN ISO 7730 or ASHRAE Standard 55 where the comfort indoor thermal is below 25°C during the daytime. Study observed that the internal surface temperature of heat resistance wall panel is up to 3°C lower than control wall panel. Therefore, we can conclude that application of heat resistance wall panel can lead to lower interior building temperature.

Grounds of two positions photovoltaic panels

OpenAIRE

Castán Fortuño, Fernando

2008-01-01

The objective of this Master Thesis is to find the optimum positioning for a two positions photovoltaic panel. Hence, it will be implemented a model in order to optimize the energy of the sun that the photovoltaic panel is receiving by its positioning. Likewise this project will include the comparison with other photovoltaic panel systems as the single position photovoltaics panels. Ultimately, it is also going to be designed a system array for the optimized model of two positions photovoltai...

Orbiter radiator panel solar focusing test

Science.gov (United States)

Howell, H. R.; Rankin, J. G.

1983-01-01

Test data are presented which define the area around the Orbiter radiator panels for which the solar reflections are concentrated to one-sun or more. The concave shape of the panels and their specular silver/Teflon coating causes focusing of the reflected solar energy which could have adverse heating effects on equipment or astronaut extravehicular activity (EVA) in the vicinity of the radiator panels. A room ambient test method was utilized with a one-tenth scale model of the radiator panels.

Evaluation and selection of aqueous-based technology for partitioning radionuclides from ICPP calcine

International Nuclear Information System (INIS)

Olson, A.L.; Schulz, W.W.; Burchfield, L.A.; Carlson, C.D.; Swanson, J.L.; Thompson, M.C.

1993-02-01

Early in 1993 Westinghouse Idaho Nuclear Company (WINCO) chartered a Panel of Nuclear Separations Experts. The purpose of this Panel was to assist WINCO scientists and engineers in selecting, evaluating, and ranking candidate aqueous-based processes and technologies for potential use in partitioning selected radionuclides from nitric acid solutions of retrieved Idaho Chemical Processing Plant (ICPP) calcine. Radionuclides of interest are all transuranium elements, 90 Sr, 99 Tc, 129 I, and 137 Cs. The six man Panel met for 4 days (February 16--19, 1993) on the campus of the Idaho State University in Pocatello, Idaho. Principal topics addressed included: Available radionuclide removal technology; applicability of separations technology and processes to ICPP calcine; and potential integrated radionuclide partitioning schemes. This report, prepared from contributions from all Panel members, presents a comprehensive account of the proceedings and significant findings of the February, 1993 meeting in Pocatello

Update of operations with Westinghouse steam generators

International Nuclear Information System (INIS)

Malinowski, D.D.; Fletcher, W.D.

1978-01-01

Westinghouse commercial steam generators in operation now number 112, of which 98 are tubed with Inconel 600, the remainder with stainless steel. The implementation of all volatile treatment (AVT) was reported. It was noted that several plants had exhibited some tube corrosion during their initial periods using AVT; this observation indicated that the transition from phosphate chemistry control to AVT may have been subject to certain residual effects due to incomplete removal of phosphated deposits. As inspection results from steam generators operated on AVT became more generally available with the passage of time, a pattern of results emerged that seemed to correlate with the operating experience with phosphate chemistry control. Specifically, all the plants that experienced corrosion problems had from 1 to 8 yr of operational history using phosphates, while those with less than a year's experience using phosphates tended to be less affected by corrosion problems

Panel discussion: Building Canadian companies and capabilities in the transition to the hydrogen economy

International Nuclear Information System (INIS)

Beck, N.

2004-01-01

'Full text:' Moderated by Nick Beck from Natural Resources Canada, this panel discussion will be prefaced by a keynote address by Dr. Arthur Carty, Canada's National Science Advisor and former President of the National Research Council of Canada, who will discuss technology commercialization in Canada and how the Government of Canada and industry collaborate to achieve their respective priorities. This session will illustrate innovative government and industry partnerships from early research and development to project demonstration, and adoption into the market-place. Panelists from across the Canadian hydrogen and fuel cell innovation spectrum will provide an overview of their respective company's partnerships with the Government of Canada and speak to how these alliances have helped their company to pioneer new technology, move technology from the lab to the marketplace, and/or become more competitive. Opportunities and challenges that companies have faced in their partnerships with government will be shared with the audience. The Panel Members are: Mr. Stephen Kukucha, Mr. Chris Reid, Mr. Robb Thompson, Mr. Pierre Rivard, Mr. John Shen, Mr. R. Randall MacEwen, Mr. Jonathan Wilkinson. Companies will also be showcasing their contribution in advancing Canada's and the world's transition to the hydrogen economy. (author)

FEMA DFIRM Panel Scheme Polygons

Data.gov (United States)

Minnesota Department of Natural Resources — This layer contains information about the Flood Insurance Rate Map (FIRM) panel areas. The spatial entities representing FIRM panels are polygons. The polygon for...

21 CFR 516.141 - Qualified expert panels.

Science.gov (United States)

2010-04-01

... choose members for the qualified expert panel in accordance with selection criteria listed in paragraph... whether the proposed qualified expert panel meets the selection criteria prior to the panel beginning its... Committee Act, as amended, 5 U.S.C. App. (b) Criteria for the selection of a qualified expert panel. (1) A...

High temperature structural sandwich panels

Science.gov (United States)

Papakonstantinou, Christos G.

High strength composites are being used for making lightweight structural panels that are being employed in aerospace, naval and automotive structures. Recently, there is renewed interest in use of these panels. The major problem of most commercial available sandwich panels is the fire resistance. A recently developed inorganic matrix is investigated for use in cases where fire and high temperature resistance are necessary. The focus of this dissertation is the development of a fireproof composite structural system. Sandwich panels made with polysialate matrices have an excellent potential for use in applications where exposure to high temperatures or fire is a concern. Commercial available sandwich panels will soften and lose nearly all of their compressive strength temperatures lower than 400°C. This dissertation consists of the state of the art, the experimental investigation and the analytical modeling. The state of the art covers the performance of existing high temperature composites, sandwich panels and reinforced concrete beams strengthened with Fiber Reinforced Polymers (FRP). The experimental part consists of four major components: (i) Development of a fireproof syntactic foam with maximum specific strength, (ii) Development of a lightweight syntactic foam based on polystyrene spheres, (iii) Development of the composite system for the skins. The variables are the skin thickness, modulus of elasticity of skin and high temperature resistance, and (iv) Experimental evaluation of the flexural behavior of sandwich panels. Analytical modeling consists of a model for the flexural behavior of lightweight sandwich panels, and a model for deflection calculations of reinforced concrete beams strengthened with FRP subjected to fatigue loading. The experimental and analytical results show that sandwich panels made with polysialate matrices and ceramic spheres do not lose their load bearing capability during severe fire exposure, where temperatures reach several

Potential biomarker panels in overall breast cancer management: advancements by multilevel diagnostics.

Science.gov (United States)

Girotra, Shantanu; Yeghiazaryan, Kristina; Golubnitschaja, Olga

2016-09-01

Breast cancer (BC) prevalence has reached an epidemic scale with half a million deaths annually. Current deficits in BC management include predictive and preventive approaches, optimized screening programs, individualized patient profiling, highly sensitive detection technologies for more precise diagnostics and therapy monitoring, individualized prediction and effective treatment of BC metastatic disease. To advance BC management, paradigm shift from delayed to predictive, preventive and personalized medical services is essential. Corresponding step forwards requires innovative multilevel diagnostics procuring specific panels of validated biomarkers. Here, we discuss current instrumental advancements including genomics, proteomics, epigenetics, miRNA, metabolomics, circulating tumor cells and cancer stem cells with a focus on biomarker discovery and multilevel diagnostic panels. A list of the recommended biomarker candidates is provided.

Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

Reliability Study in Solar Panels

OpenAIRE

Español Lifante, Albert

2012-01-01

Crystalline silicon Modules are formed by single silicon photovoltaic cells. Since each one of these cells individually contributes to the overall electric power of the panel, the failure of one of them directly affects to its benefits and performance. To Minimize these negative effects, junction boxes with few bypass diodes are usually included in Photovoltaic Solar panels. A still experimental way to built solar panels is to integrate bypass diodes in every single cell, which would in...

Contributions of China’s Wood-Based Panels to CO2 Emission and Removal Implied by the Energy Consumption Standards

Directory of Open Access Journals (Sweden)

Shanshan Wang

2017-07-01

Full Text Available Life cycle analysis on wood-based panels in terms of CO2 flux can be used to quantitatively assess the climate change contributions of these materials. In this study, the annual CO2 flux between 1990 and 2015 was calculated through gate-to-gate life cycle analysis of wood-based panels. As implied by the energy consumption standards, China’s wood-based panels used to be carbon sources during the period 1990–2007, with the average contribution to CO2 emissions of 9.20 Mt/year. The implementation of new standards and the development of Cleaner production technologies in China, decreased the energy consumption per panel. China’s wood-based panels acted as a carbon sink between 2008 and 2015, with the average contribution to CO2 removal of 31.71 Mt/year. Plywood produced the largest contributions to the emission and removal of CO2, and was followed by fiberboard and particleboard. China’s wood-based panels, with good prospects and strong demands projected in the future, can potentially contribute to climate change mitigation.

Sound transmission loss of composite sandwich panels

Science.gov (United States)

Zhou, Ran

Light composite sandwich panels are increasingly used in automobiles, ships and aircraft, because of the advantages they offer of high strength-to-weight ratios. However, the acoustical properties of these light and stiff structures can be less desirable than those of equivalent metal panels. These undesirable properties can lead to high interior noise levels. A number of researchers have studied the acoustical properties of honeycomb and foam sandwich panels. Not much work, however, has been carried out on foam-filled honeycomb sandwich panels. In this dissertation, governing equations for the forced vibration of asymmetric sandwich panels are developed. An analytical expression for modal densities of symmetric sandwich panels is derived from a sixth-order governing equation. A boundary element analysis model for the sound transmission loss of symmetric sandwich panels is proposed. Measurements of the modal density, total loss factor, radiation loss factor, and sound transmission loss of foam-filled honeycomb sandwich panels with different configurations and thicknesses are presented. Comparisons between the predicted sound transmission loss values obtained from wave impedance analysis, statistical energy analysis, boundary element analysis, and experimental values are presented. The wave impedance analysis model provides accurate predictions of sound transmission loss for the thin foam-filled honeycomb sandwich panels at frequencies above their first resonance frequencies. The predictions from the statistical energy analysis model are in better agreement with the experimental transmission loss values of the sandwich panels when the measured radiation loss factor values near coincidence are used instead of the theoretical values for single-layer panels. The proposed boundary element analysis model provides more accurate predictions of sound transmission loss for the thick foam-filled honeycomb sandwich panels than either the wave impedance analysis model or the

Effect of alcohol vapor treatment on electrical and optical properties of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) films for indium tin oxide-free organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Fallahzadeh, Ali, E-mail: afa.phy@gmail.com; Saghaei, Jaber; Yousefi, Mohammad Hassan

2014-11-30

Graphical abstract: - Highlights: • A simple alcohol vapor treatment (AVT) technique was applied to enhance the conductivity of PEDOT:PSS films. • Alcohols with one OH group can improve conductivity of PEDOT:PSS films by this technique. • Mechanism of conductivity enhancement of PEDOT:PSS films by AVT method was explained. • ITO-free OLEDs were fabricated using highly conductive AVT PEDOT:PSS films standalone anode. - Abstract: A simple alcohol vapor treatment (AVT) technique was proposed to improve the conductivity of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. In this technique, various alcohols, i.e. methanol, ethanol, 2-propanol and ethylene glycol, were applied to treat the surface of the films formed and then they were annealed. The sheet resistance of PEDOT:PSS films was significantly reduced from 130 kΩ/sq to 60 Ω/sq when treated with methanol vapor. The investigation of the vertical resistance of the films showed that the sample treated with methanol vapor displayed the lowest resistance as well. The mechanism of conductivity enhancement of PEDOT:PSS films through AVT method was explained by surface phase images, UV and IR spectra of PEDOT:PSS films. Optical transmittance spectrum of treated films exhibited that AVT has even enhanced the optical transmittance slightly. Improvement in the morphology, electrical and optical properties of PEDOT:PSS films prompted their applications as a transparent anode in the fabrication of ITO-free organic light-emitting diodes (OLEDs). The OLED manufactured based on methanol-treated PEDOT:PSS films demonstrated the highest luminance.

75 FR 82376 - North American Free Trade Agreement, Article 1904 NAFTA Panel Reviews; Request for Panel Review

Science.gov (United States)

2010-12-30

... Mexico and the People's Republic of China. This determination was published in the Federal Register (75... Panel Review. SUMMARY: On December 22, 2010, the Government of Mexico filed a First Request for Panel... Government of Mexico established Rules of Procedure for Article 1904 Binational Panel Reviews (``Rules...

Solar panel foundation device

Energy Technology Data Exchange (ETDEWEB)

Hawley, W.W.

1983-03-29

A transportable solar panel foundation device which has a bottom member, at least one upstanding side member, and an essentially open top. The side members are angled to permit nesting of a plurality of the foundation devices, and reinforcement pads are carried by the foundation device to support legs for one or more solar panels.

Law Panel in action.

Science.gov (United States)

Odulana, J

In September 1976 the Africa Regional Council (ARC) of IPPF created a Law Panel to 1) advise the ARC on the emphasis of laws and parenthood programs in the region, 2) investigate legal obstacles to family planning and ways of removing them, 3) institute a monitoring service on laws and court decisions affecting planned parenthood, and 4) prepare a list of lawyers and legal reformers by country. The panel has 1) recommended adoption of an IPPF Central Medical Committee and Central Law Panel statement on sterilization, adolescent fertility control, and the use of medical and auxiliary personnel in family planning services with guidelines for Africa; 2) appointed National Legal Correspondents to carry on the monitoring service mentioned above in 18 countries; and 3) discussed solutions to problems in delivering family planning services with family planning associations in Tanzania, Zambia, Mauritius, Madagascar, and Kenya. Laws governing family planning education and services, marriage, divorce, and maternity benefits in these countries are summarized. In 1978 the panel will hold 2 workshops on law and the status of women.

PVT Panels. Fully renewable and competitive

International Nuclear Information System (INIS)

Bakker, M.; Strootman, K.J.; Jong, M.J.M.

2003-10-01

A photovoltaic/thermal (PVT) panel is a combination of photovoltaic cells with a solar thermal collector, generating solar electricity and solar heat simultaneously. PVT panels generate more solar energy per unit surface area than a combination of separate PV panels and solar thermal collectors, and share the aesthetic advantage of PV. After several years of research, PVT panels have been developed into a product that is now ready for market introduction. One of the most promising system concepts, consisting of 25 m 2 of PVT panels and a ground coupled heat pump, has been simulated in TRNSYS, and has been found to be able to fully cover both the building related electricity and heat consumption, while keeping the long-term average ground temperature constant. The cost and payback time of such a system have been determined; it has been found that the payback time of this system is approximately two-thirds of the payback time of an identical system but with 21 m 2 of PV panels and 4 m 2 of solar thermal collectors. Finally, by looking at the expected growth in the PV and solar thermal collector market, the market potential for for PVT panels has been found to be very large

Validation of Ion TorrentTM Inherited Disease Panel with the PGMTM Sequencing Platform for Rapid and Comprehensive Mutation Detection

Directory of Open Access Journals (Sweden)

Abeer E. Mustafa

2018-05-01

Full Text Available Quick and accurate molecular testing is necessary for the better management of many inherited diseases. Recent technological advances in various next generation sequencing (NGS platforms, such as target panel-based sequencing, has enabled comprehensive, quick, and precise interrogation of many genetic variations. As a result, these technologies have become a valuable tool for gene discovery and for clinical diagnostics. The AmpliSeq Inherited Disease Panel (IDP consists of 328 genes underlying more than 700 inherited diseases. Here, we aimed to assess the performance of the IDP as a sensitive and rapid comprehensive gene panel testing. A total of 88 patients with inherited diseases and causal mutations that were previously identified by Sanger sequencing were randomly selected for assessing the performance of the IDP. The IDP successfully detected 93.1% of the mutations in our validation cohort, achieving high overall gene coverage (98%. The sensitivity for detecting single nucleotide variants (SNVs and short Indels was 97.3% and 69.2%, respectively. IDP, when coupled with Ion Torrent Personal Genome Machine (PGM, delivers comprehensive and rapid sequencing for genes that are responsible for various inherited diseases. Our validation results suggest the suitability of this panel for use as a first-line screening test after applying the necessary clinical validation.

Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

Directory of Open Access Journals (Sweden)

Hee-Jong Choi

2011-12-01

Full Text Available In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60 hull and KRISO container ship (KCS, a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI. The computational results were validated by comparing with the existing experimental data.

Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

Science.gov (United States)

Choi, Hee-Jong; Chun, Ho-Hwan; Park, Il-Ryong; Kim, Jin

2011-12-01

In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60) hull and KRISO container ship (KCS), a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI). The computational results were validated by comparing with the existing experimental data.

New directions in fusion machines: report on the MFAC Panel X on high power density options

Energy Technology Data Exchange (ETDEWEB)

Linford, R.K.

1985-01-01

The high cost of fusion is motivating a shift in research interest toward smaller, lower-cost systems. Panel X of the Magnetic Fusion Advisory Committee (MFAC) was charged to assess the potential benefits and problems associated with small, high-power-density approaches to fusion. The Panel identified figures of merit which are useful in evaluating various approaches to reduce the development costs and capital costs of fusion systems. As a result of their deliberations, the Panel recommended that ''...increased emphasis should be given to improving the mass power density of fusion systems, aiming at a minimum target of 100 kWe/tonne'', and that ''Increased emphasis should be given to concepts that offer the potential to reduce substantially the cost of development steps in physics and technology.''

[The influence of printing technology conditions on the accuracy and reproducibility of printed contrast panels for assessing contrast sensitivity].

Science.gov (United States)

Raabe, T; Jung, U; Wilhelm, H

2014-08-01

Contrast studies can provide important knowledge for treatment decisions before surgery or for assessing the driving ability of professional drivers. Accordingly, high demands are placed on contrast panels to obtain reliable and reproducible results. The aim of the study is to find out if the contrast panels on the market meet the requirements. On the basis of measurement evaluation and schematic presentations potential sources of error can be identified. These sources of error may have a decisive influence on the assessment of contrast vision. Far-reaching analyses have shown that three parameters can have a significant influence on the accuracy and reproducibility of printed contrast panels. This holds for certain properties of the printing substrate, the type of representation of display element, and the choice of the colourant. Only the correct interaction between the substrate and the print colour effects an angle-independent contrast. A matt substrate is necessary, which has a low difference to the printed contrast element in respect of glow, so that possible angle differences have no influence on the contrast assessment. The contrast elements of a contrast panel vary in brightness. Conventional methods for typographical representation of different brightnesses use the method of screening. This causes undesirable edges, which weaken in particular the lower-contrast elements unintentionally. Use of special colours can avoid this effect. In the visible wavelength range the studied contrast elements have an irregular absorption behaviour. Because of differences between the lighting surroundings, this can lead to a differentiated stimulation of cones in practice. Appropriate colourants have a constant absorption behaviour. To get representative results of contrast studies the production of contrast panels needs more knowledge about the interaction between paper and colour than is typically required for print products. On the basis of a prototype optimisation

Using Retrofit Nail Base Panels to Expand the Market for Wall Upgrades

Energy Technology Data Exchange (ETDEWEB)

Del Bianco, M. [Home Innovation Research Lab., Upper Marlboro, MD (United States); Wiehagen, J. [Home Innovation Research Lab., Upper Marlboro, MD (United States)

2016-02-01

This project evaluated the effectiveness and affordability of integrating retrofit insulated panels into a re-siding project. The Partnership for Home Innovation (PHI) teamed with New York State Energy Research and Development Authority (NYSERDA), the Albany Housing Authority (AHA), and the New York State Weatherization Assistance Program (WAP) administered by Albany Community Action Partnership to demonstrate an energy retrofit and siding upgrade on a two-story, seven unit, multifamily building in Albany New York (CZ 5). The project focused on accomplishing three goals - doubling the existing wall thermal resistance (from approximately R-13 to a weighted average of R-27), reduction of building air leakage, and completion of the retrofit within a budget where the additional cost for upgrading wall's thermal resistance is equal to the cost of the standard re-siding effort (i.e., the total cost of the energy efficient re-siding scope of work is not more than double the cost of the standard re-siding effort). Lessons learned from the project strongly indicate that the retrofit panel technology can be installed using common installation practices and with minimal training. Other lessons learned include limitation on the use of standard air sealing materials during cold weather installations and the need to develop better installation guidance for trades working with the level of tolerances that may be present in the existing structure. This technology demonstration showed that exterior retrofit panels provide a viable and reasonable option for the siding trades to increase market opportunities and achieve synergistic benefits for aesthetic upgrades to a building's exterior.

Carbon Nanotube Thin Film Transistors for Flat Panel Display Application.

Science.gov (United States)

Liang, Xuelei; Xia, Jiye; Dong, Guodong; Tian, Boyuan; Peng, Lianmao

2016-12-01

Carbon nanotubes (CNTs) are promising materials for both high performance transistors for high speed computing and thin film transistors for macroelectronics, which can provide more functions at low cost. Among macroelectronics applications, carbon nanotube thin film transistors (CNT-TFT) are expected to be used soon for backplanes in flat panel displays (FPDs) due to their superior performance. In this paper, we review the challenges of CNT-TFT technology for FPD applications. The device performance of state-of-the-art CNT-TFTs are compared with the requirements of TFTs for FPDs. Compatibility of the fabrication processes of CNT-TFTs and current TFT technologies are critically examined. Though CNT-TFT technology is not yet ready for backplane production line of FPDs, the challenges can be overcome by close collaboration between research institutes and FPD manufacturers in the short term.

Solar panel assembly and support pad

Energy Technology Data Exchange (ETDEWEB)

Hawley, W.W.

1980-10-07

A solar panel assembly is described comprising at least one solar panel, support means for carrying said panel, and at least one support pad having a base plate, upstanding longitudinal sides, and spaced apart flange means for connection to said support means, said upstanding sides and opposed flange means defining an interior volume for receiving and holding weighting material.

JERAMI SEBAGAI BAHAN BAKU PANEL AKUSTIK PELAPIS DINDING

Directory of Open Access Journals (Sweden)

Christina E. Mediastika

2008-01-01

Full Text Available The demand of walling panels with acoustic qualification has surprisingly increased, due to the needs for home theaters and mini recording studios in the increase of environmental noise. Therefore, good supply of acoustic panels, especially those with lower price are necessary. A series of study to explore possibility in using paddy-straw as main material to construct cheap and high quality panels has been developed. Prior to this study, an earlier small research showed there was a great potency in using paddy-straw as panels, especially ones drawn from paddy in type IR. The earlier study recommends further research to examine strength of compression and tensile of the constructed panels to go for building materials, which is presented in this paper. Acoustic qualification of the panels is subject for further reserach. Abstract in Bahasa Indonesia: Kebutuhan akan panel pelapis dinding yang bersifat akustik terus meningkat seiring meningkatnya kebisingan dan kebutuhan terhadap ruang studio pribadi. Ketersediaan panel pelapis dinding dengan harga yang lebih terjangkau seperti yang terbuat dari bahan limbah sangatlah dibutuhkan. Pada penelitian awal telah diselidiki kemungkinan penggunaan jerami yang merupakan limbah sebagai bahan baku pembuatan panel akustik. Penelitian tersebut menunjukkan bahwa jerami sangat potensial digunakan sebagai bahan aku panel, terutama jerami padi berjenis IR. Selanjutnya panel jerami ini perlu mendapatkan perlakukan uji desak dan lentur untuk memastikan kemampuannya menahan berat sendiri dan kekuatannya saat proses penggunaan, sebelum akhirnya mengalami pengujian berkaitan dengan kualitas akustik. Kekuatan desak dan lentur panel dimaksud, tersaji dalam tulisan ini. Kata kunci: panel jerami, uji desak, uji lentur.

Report of Industry Panel Group

Science.gov (United States)

Gallimore, Simon; Gier, Jochen; Heitland, Greg; Povinelli, Louis; Sharma, Om; VandeWall, Allen

2006-01-01

A final report is presented from the industry panel group. The contents include: 1) General comments; 2) Positive progress since Minnowbrook IV; 3) Industry panel outcome; 4) Prioritized turbine projects; 5) Prioritized compressor projects; and 6) Miscellaneous.

KUALITAS AKUSTIK PANEL DINDING BERBAHAN BAKU JERAMI

Directory of Open Access Journals (Sweden)

Christina E. Mediastika

2008-01-01

Full Text Available A series of study to explore possibility in using paddy-straw as main material to construct cheap and high quality panels has been developed. Prior to this study, laboratory research to examine strength of compression and tensile of the panels have been conducted, which is showed a significant value for a non-structural panel. The compression is 15 N/mm2 and tensile averaged at 0,5 N/mm2 . In this study, acoustic properties of the panels is to be examined, i.e.: transmission loss (TL, absorption coefficient (, and reverberation time (RT60. The test showed TL of 10 dB and 16 dB,  of 0,4 and 0,8 and improve RT60 from 0,88 sec to 0,35 sec and 0,16 sec (500 Hz is used for reference. Abstract in Bahasa Indonesia: Ketersediaan panel pelapis dinding yang bersifat akustik dengan harga yang lebih terjangkau seperti yang terbuat dari bahan limbah sangatlah penting. Pada penelitian awal telah diselidiki penggunaan jerami sebagai bahan baku pembuatan panel akustik, sekaligus telah dilakukan pengujian terhadap kareakteristik struktural (uji desak dan lentur dari panel tersebut. Dari uji kekuatan struktural, panel memiliki kekuatan desak mencapai 15 N/mm2 dan kuat lentur reta-rata 0,5 N/mm2. Kekuatan ini dianggap mencukupi bagi panel non-struktural yang hanya bertugas untuk memikul beban sendiri. Oleh karena tujuan awal pembuatan panel adalah untuk kepentingan akustik, maka pada penelitian lanjutan, dilakukan uji laboratorium dan lapangan untuk melihat karakterisktik akustiknya. Adapun pengujian meliputi: redaman/insulasi (TL, koefisien serap ( dan waktu dengung (RT60. Dari hasil pengujian, panel mempunyai TL 10 dB dan 16 dB,  0,4 dan 0,8, serta mampu memperbaiki RT60 ruangan dari 0,88 detik menjadi 0,35 detik dan 0,16 detik. Kesemua pengujian menggunakan band frekuensi 500 Hz sebagai acuan. Kata kunci: panel jerami, insulasi, koefisien serap, waktu dengung.

Review of flat panel display programs and defense applications

Science.gov (United States)

Gnade, Bruce; Schulze, Raymond; Henderson, Girardeau L.; Hopper, Darrel G.

1997-07-01

Flat panel display research has comprised a substantial portion of the national investment in new technology for economic and national security for the past nine years. These investments have ben made principally via several Defense Advanced Research Projects Agency (DARPA) programs, known collectively as the continuing High Definition Systems Program, and the Office of the Secretary of Defense Production Act Title III Program. Using input from the Army, Navy, and Air Force to focus research and identify insertion opportunities, DARPA and the Title III Program Office have made investments to develop the national technology base and manufacturing infrastructure necessary to meet the twin challenge of providing affordable displays in current systems and enabling the DoD strategy of winning future conflicts by getting more information to all participants during the battle. These research programs are reviewed and opportunities for applications are described. Future technology development, transfer, and transition requirements are identified. Strategy and vision are documented to assist the identification of areas meriting further consideration.

Efficiency enhancement of liquid crystal projection displays using light recycle technology

Science.gov (United States)

Wang, Y.

2002-01-01

A new technology developed at JPL using low absorption color filters with polarization and color recycle system, is able to enhance efficiency of a single panel liquid crytal display (LCD) projector to the same efficiency of a 3 panel LCD projector.

Clinical Study of Acute Vasoreactivity Testing in Patients with Chronic Thromboembolic Pulmonary Hypertension

Institute of Scientific and Technical Information of China (English)

Qi-Xia Xu; Yuan-Hua Yang; Jie Geng; Zhen-Guo Zhai; Juan-Ni Gong; Ji-Feng Li; Xiao Tang

2017-01-01

Background:The clinical significance of acute vasoreactivity testing (AVT) in patients with chronic thromboembolic pulmonary hypertension (CTEPH) remains unclear.We analyzed changes in hemodynamics and oxygenation dynamics indices after AVT in patients with CTEPH using patients with pulmonary arterial hypertension (PAH) as controls.Methods:We analyzed retrospectively the results of AVT in 80 patients with PAH and 175 patients with CTEPH registered in the research database ofBeijing Chao-Yang Hospital between October 2005 and August 2014.Demographic variables,cardiopulmonary indicators,and laboratory findings were compared in these two subgroups.A long-term follow-up was conducted in patients with CTEPH.Between-group comparisons were performed using the independent-sample t-test or the rank sum test,within-group comparisons were conducted using the paired t-test or the Wilcoxon signed-rank test,and count data were analyzed using the Chi-squared test.Survival was estimated using the Kaplan-Meier method and log-rank test.Results:The rates of positive response to AVT were similar in the CTEPH (25/175,14.3％) and PAH (9/80,11.3％) groups (P ＞ 0.05).Factors significantly associated a positive response to AVT in the CTEPH group were level of N-terminal pro-brain natriuretic peptide (≤1131.000 ng/L),mean pulmonary arterial pressure (mPAP,≤44.500 mmHg),pulmonary vascular resistance (PVR,≤846.500 dyn·s1·m-5),cardiac output (CO,≥3.475 L/min),and mixed venous oxygen partial pressure (PvO2,≥35.150 mmHg).Inhalation of iloprost resulted in similar changes in mean blood pressure,mPAP,PVR,systemic vascular resistance,CO,arterial oxygen saturation (SaO2),mixed venous oxygen saturation,partial pressure of oxygen in arterial blood (PaO2),PvO2,and intrapulmonary shunt (Qs/Qt) in the PAH and CTEPH groups (all P ＞ 0.05).The survival time in patients with CTEPH with a negative response to AVT was somewhat shorter than that in AVT-responders although the difference was

Panel Smooth Transition Regression Models

DEFF Research Database (Denmark)

González, Andrés; Terasvirta, Timo; Dijk, Dick van

We introduce the panel smooth transition regression model. This new model is intended for characterizing heterogeneous panels, allowing the regression coefficients to vary both across individuals and over time. Specifically, heterogeneity is allowed for by assuming that these coefficients are bou...

Solar Panel Integration as an Alternate Power Source on Centaur 2 (SPIAPS)

Science.gov (United States)

Gebara, Christine A.; Schuetze, Nich A.; Knochel, Aviana M.; Magruder, Darby F.

2011-01-01

The dream of exploration has inspired thousands throughout time. Space exploration, in particular, has taken the past century by storm and caused a great advance in technology. In this project, a retractable solar panel array will be developed for use on the Centaur 2 Rover. Energy generated by the solar panels will go to power the Centaur 2 Robot (C2) or Regolith & Environment Science & Oxygen & Lunar Volatile Extraction (RESOLVE) payload, an in-situ resource utilization project. Such payload is designed to drill into lunar and Martian terrain as well as be able to conduct other geological testing; RESOLVE is slated for testing in 2012. Ultimately, this project will fit into NASA s larger goal of deep space exploration as well as long term presence outside Earth s orbit.

Comparing parametric and nonparametric regression methods for panel data

DEFF Research Database (Denmark)

Czekaj, Tomasz Gerard; Henningsen, Arne

We investigate and compare the suitability of parametric and non-parametric stochastic regression methods for analysing production technologies and the optimal firm size. Our theoretical analysis shows that the most commonly used functional forms in empirical production analysis, Cobb......-Douglas and Translog, are unsuitable for analysing the optimal firm size. We show that the Translog functional form implies an implausible linear relationship between the (logarithmic) firm size and the elasticity of scale, where the slope is artificially related to the substitutability between the inputs....... The practical applicability of the parametric and non-parametric regression methods is scrutinised and compared by an empirical example: we analyse the production technology and investigate the optimal size of Polish crop farms based on a firm-level balanced panel data set. A nonparametric specification test...

Hexagon solar power panel

Science.gov (United States)

Rubin, I. (Inventor)

1978-01-01

A solar energy panel support is described upon which silicon cells are arrayed. The cells are wafer thin and of two geometrical types, both of the same area and electrical rating, namely hexagon cells and hourglass cells. The hourglass cells are composites of half hexagons. A near perfect nesting relationship of the cells achieves a high density packing whereby optimum energy production per panel area is achieved.

Brain arginine vasotocin and isotocin in breeding female three-spined sticklebacks (Gasterosteus aculeatus): the presence of male and egg deposition.

Science.gov (United States)

Kulczykowska, Ewa; Kleszczyńska, Agnieszka

2014-08-01

Arginine vasotocin (AVT) and isotocin (IT) are fish hypothalamic nonapeptides involved in numerous social and reproductive behaviors. Vasotocinergic and isotocinergic fibers project to different brain areas where peptides act as neurotransmitters and/or neuromodulators. In this study, we measured whole brain levels of bioactive AVT and IT in breeding females of three-spined stickleback (Gasterosteus aculeatus) when they were kept with: (i) courting nest-owners, (ii) courting males that did not build the nest, (iii) non-courting males, and (iv) alone. Only some of the females kept with courting nest-owners deposited eggs. The highest and similar brain AVT levels were in those of females that did not deposit eggs, regardless of whether they were kept with non-courting or courting male, having the nest or not. The highest IT levels were in females that did not deposit eggs but only in those kept with courting male. We suggest that production of AVT in females' brain is stimulated by the presence of male in close proximity, irrespective of whether or not it displays courting behavior, but that of IT is stimulated by male courtship proxies. Moreover, presence of courting or non-courting male that stimulate IT or/and AVT producing neurones may be decisive for final oocyte maturation or egg deposition, because brain levels of both nonapeptides decrease after egg deposition. Similar AVT levels in brains of aggressive and non-aggressive individuals and lack of correlation between brain IT levels and aggressive behavior of females suggest that the nonapeptides are not related to females aggressiveness in three-spined sticklebacks. Copyright © 2014. Published by Elsevier Inc.

Flat-Panel Computed Tomography (DYNA-CT) in Neuroradiology. From High-Resolution Imaging of Implants to One-Stop-Shopping for Acute Stroke.

Science.gov (United States)

Doerfler, A; Gölitz, P; Engelhorn, T; Kloska, S; Struffert, T

2015-10-01

Originally aimed at improving standard radiography by providing higher absorption efficiency and a wider dynamic range, flat-panel detector technology has meanwhile got widely accepted in the neuroradiological community. Especially flat-panel detector computed tomography (FD-CT) using rotational C-arm mounted flat-panel detector technology is capable of volumetric imaging with a high spatial resolution. By providing CT-like images of the brain within the angio suite, FD-CT is able to rapidly visualize hemorrhage and may thus improve complication management without the need of patient transfer. As "Angiographic CT" FD-CT may be helpful during many diagnostic and neurointerventional procedures and for noninvasive monitoring and follow-up. In addition, spinal interventions and high-resolution imaging of the temporal bone might also benefit from FD-CT. Finally, using novel dynamic perfusion and angiographic protocols, FD-CT may provide functional information on brain perfusion and vasculature with the potential to replace standard imaging in selected acute stroke patients.

Control panel for CMC 8080 crate controller

International Nuclear Information System (INIS)

Masayuki Inokuchi

1978-01-01

The main features of Control Panel for CAMAC Crate Controller CMC 8080 are described. The control panel can be directly connected with CRATE CONTROLLER's front panel connector with a 50 lines cable without any changes in CMC 8080 system circuits. (author)

A pilot study to evaluate the application of a generic protein standard panel for quality control of biomarker detection technologies

Directory of Open Access Journals (Sweden)

Valdivia Hernan J

2011-08-01

Full Text Available Abstract Background Protein biomarker studies are currently hampered by a lack of measurement standards to demonstrate quality, reliability and comparability across multiple assay platforms. This is especially pertinent for immunoassays where multiple formats for detecting target analytes are commonly used. Findings In this pilot study a generic panel of six non-human protein standards (50 - 10^7 pg/mL of varying abundance was prepared as a quality control (QC material. Simulated "normal" and "diseased" panels of proteins were prepared in pooled human plasma and incorporated into immunoassays using the Meso Scale Discovery® (MSD® platform to illustrate reliable detection of the component proteins. The protein panel was also evaluated as a spike-in material for a model immunoassay involving detection of ovarian cancer biomarkers within individual human plasma samples. Our selected platform could discriminate between two panels of the proteins exhibiting small differences in abundance. Across distinct experiments, all component proteins exhibited reproducible signal outputs in pooled human plasma. When individual donor samples were used, half the proteins produced signals independent of matrix effects. These proteins may serve as a generic indicator of platform reliability. Each of the remaining proteins exhibit differential signals across the distinct samples, indicative of sample matrix effects, with the three proteins following the same trend. This subset of proteins may be useful for characterising the degree of matrix effects associated with the sample which may impact on the reliability of quantifying target diagnostic biomarkers. Conclusions We have demonstrated the potential utility of this panel of standards to act as a generic QC tool for evaluating the reproducibility of the platform for protein biomarker detection independent of serum matrix effects.

Evaluation of flat panel PMT for gamma ray imaging

International Nuclear Information System (INIS)

Pani, R.; Cinti, M.N.; Pellegrini, R.; Trotta, C.; Trotta, G.; Montani, L.; Ridolfi, S.; Garibaldi, F.; Scafe, R.; Belcari, N.; Del Guerra, A.

2003-01-01

The first position sensitive PMT, Hamamatsu R2486, developed in 1985, represented a strong technological advance for gamma-ray imaging. Hamamatsu H8500 Flat Panel PMT is the last generation position sensitive PMT: extremely compact with 2 in. active area. Its main features are: minimum peripheral dead zone (1 mm) and height of 12 mm. It was designed to be assembled in array to cover large detection area. It can represent a technical revolution for many applications in the field of gamma-ray imaging as for example nuclear medicine. This tube is based on metal channel dynode for charge multiplication and 8x8 anodes for charge collection and position calculation. In this paper we present a preliminary evaluation of the imaging performances addressed to nuclear medicine application. To this aim we have taken into account two different electronic readouts: resistive chain with Anger Camera principle and multianode readout. Flat panel PMT was coupled to CsI(Tl) and NaI(Tl) scintillation arrays. The results were also compared with the first generation PSPMT

Shape Morphing Adaptive Radiator Technology (SMART) for Variable Heat Rejection

Science.gov (United States)

Erickson, Lisa

2016-01-01

The proposed technology leverages the temperature dependent phase change of shape memory alloys (SMAs) to drive the shape of a flexible radiator panel. The opening/closing of the radiator panel, as a function of temperature, passively adapts the radiator's rate of heat rejection in response to a vehicle's needs.

PV panel model based on datasheet values

DEFF Research Database (Denmark)

Sera, Dezso; Teodorescu, Remus; Rodriguez, Pedro

2007-01-01

This work presents the construction of a model for a PV panel using the single-diode five-parameters model, based exclusively on data-sheet parameters. The model takes into account the series and parallel (shunt) resistance of the panel. The equivalent circuit and the basic equations of the PV cell....... Based on these equations, a PV panel model, which is able to predict the panel behavior in different temperature and irradiance conditions, is built and tested....

Proceedings of the driving safety technology forum

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

This one day forum focused on improving driving safety in the petroleum industry by introducing new technologies and strategies. The forum featured several keynote addresses on driving safety as well as the Government of Alberta's Tactical Plan and Alberta Road Safety at Work Strategy. Presentations consisted of success stories of new technology or process applications or proposed technology demonstration projects followed by question and answer panels around the following topics: industry and government strategies; driver fatigue management and prevention; driver behaviour and culture change; vehicle monitoring systems and innovative wildlife avoidance techniques. Specific presentations addressed BP's driving safety strategy, in-cabin air quality and truck drivers' health and safety and how Talisman Energy implemented oilfield fleet safety using event driven automated vehicle location technologies. A total of 3 keynote addresses, 3 panel question and answer sessions and 11 presentations were presented at the conference, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Fuel demand in Brazil in a dynamic panel data approach

International Nuclear Information System (INIS)

Santos, Gervásio F.

2013-01-01

The purpose of this paper is to evaluate the sensitivity of fuel consumers regarding price and income, taking recent changes in the Brazilian fuel market into account. In this market, new market rules, energy policy towards fuel diversification and introduction of flex-fuel engines have determined fuel competition among gasoline, ethanol and compressed natural gas. Using a dynamic panel data model, demand equations for these three fuels are econometrically estimated to obtain consumer adjustment coefficients, price, cross-price and income elasticities in the short and long-run. In addition, the effect of the introduction of flex-fuel engines in the market and the rationality of consumers towards efficiency constraints of the engines were tested. Apart from considerable competition, results show that the dynamics of the Brazilian fuel market revolves around ethanol instead of gasoline. While demands for gasoline and natural gas are inelastic to price, demand for ethanol is elastic in Brazil. Furthermore, after the introduction of the flex-fuel technology the sensitivity of consumers to fuel prices changed, and ethanol consumers take efficiency constrains into account when ethanol prices reach the threshold of 70% of gasoline prices. - Highlights: ► Fuel demand in Brazil is evaluated, considering the changes in the fuel market. ► A dynamic panel data model is used to fit demand equations for fuels. ► Adjustment coefficients, price, cross-price and income elasticities are estimated. ► The impact of flex-fuel technology on the consumer behavior is tested. ► The results showed that the dynamic of the fuel market revolves around ethanol. ► The flex-fuel technology increased the competition among fuels

Technology Requirements for Information Management

Science.gov (United States)

Graves, Sara; Knoblock, Craig A.; Lannom, Larry

2002-01-01

This report provides the results of a panel study conducted into the technology requirements for information management in support of application domains of particular government interest, including digital libraries, mission operations, and scientific research. The panel concluded that it was desirable to have a coordinated program of R&D that pursues a science of information management focused on an environment typified by applications of government interest - highly distributed with very large amounts of data and a high degree of heterogeneity of sources, data, and users.

Thin film photovoltaic panel and method

Science.gov (United States)

Ackerman, Bruce; Albright, Scot P.; Jordan, John F.

1991-06-11

A thin film photovoltaic panel includes a backcap for protecting the active components of the photovoltaic cells from adverse environmental elements. A spacing between the backcap and a top electrode layer is preferably filled with a desiccant to further reduce water vapor contamination of the environment surrounding the photovoltaic cells. The contamination of the spacing between the backcap and the cells may be further reduced by passing a selected gas through the spacing subsequent to sealing the backcap to the base of the photovoltaic panels, and once purged this spacing may be filled with an inert gas. The techniques of the present invention are preferably applied to thin film photovoltaic panels each formed from a plurality of photovoltaic cells arranged on a vitreous substrate. The stability of photovoltaic conversion efficiency remains relatively high during the life of the photovoltaic panel, and the cost of manufacturing highly efficient panels with such improved stability is significantly reduced.

Panel Debate: Technics and technology in mathematics and mathematics education

DEFF Research Database (Denmark)

Misfeldt, Morten

2015-01-01

The use of computer technology for teaching and learning of mathematics has several consequences and does sometimes give rise to both controversies and misunderstandings. We address these problems by both a philosophical and a historical approach, investigating what it actually is that goes on when...... guidelines and conclusions regarding the use of computer technology in mathematics education....... new technologies enter mathematics as a discipline and mathematics education as a societal practice. Our analysis suggests a focus on continuities in time and place in the sense that it is necessary to understand the history of “tool use” in mathematics and the various ways that scholastic and non...

Aerosol Deposition and Solar Panel Performance

Science.gov (United States)

Arnott, W. P.; Rollings, A.; Taylor, S. J.; Parks, J.; Barnard, J.; Holmes, H.

2015-12-01

Passive and active solar collector farms are often located in relatively dry desert regions where cloudiness impacts are minimized. These farms may be susceptible to reduced performance due to routine or episodic aerosol deposition on collector surfaces. Intense episodes of wind blown dust deposition may negatively impact farm performance, and trigger need to clean collector surfaces. Aerosol deposition rate depends on size, morphology, and local meteorological conditions. We have developed a system for solar panel performance testing under real world conditions. Two identical 0.74 square meter solar panels are deployed, with one kept clean while the other receives various doses of aerosol deposition or other treatments. A variable load is used with automation to record solar panel maximum output power every 10 minutes. A collocated sonic anemometer measures wind at 10 Hz, allowing for both steady and turbulent characterization to establish a link between wind patterns and particle distribution on the cells. Multispectral photoacoustic instruments measure aerosol light scattering and absorption. An MFRSR quantifies incoming solar radiation. Solar panel albedo is measured along with the transmission spectra of particles collected on the panel surface. Key questions are: At what concentration does aerosol deposition become a problem for solar panel performance? What are the meteorological conditions that most strongly favor aerosol deposition, and are these predictable from current models? Is it feasible to use the outflow from an unmanned aerial vehicle hovering over solar panels to adequately clean their surface? Does aerosol deposition from episodes of nearby forest fires impact performance? The outlook of this research is to build a model that describes environmental effects on solar panel performance. Measurements from summer and fall 2015 will be presented along with insights gleaned from them.

A Pilot Study of Telepractice for Teaching Listening and Spoken Language to Mandarin-Speaking Children with Congenital Hearing Loss

Science.gov (United States)

Chen, Pei-Hua; Liu, Ting-Wei

2017-01-01

Telepractice provides an alternative form of auditory-verbal therapy (eAVT) intervention through videoconferencing; this can be of immense benefit for children with hearing loss, especially those living in rural or remote areas. The effectiveness of eAVT for the language development of Mandarin-speaking preschoolers with hearing loss was…

Numerical simulation of wind loads on solar panels

Science.gov (United States)

Su, Kao-Chun; Chung, Kung-Ming; Hsu, Shu-Tsung

2018-05-01

Solar panels mounted on the roof of a building or ground are often vulnerable to strong wind loads. This study aims to investigate wind loads on solar panels using computational fluid dynamic (CFD). The results show good agreement with wind tunnel data, e.g. the streamwise distribution of mean surface pressure coefficient of a solar panel. Wind uplift for solar panels with four aspect ratios is evaluated. The effect of inclined angle and clearance (or height) of a solar panel is addressed. It is found that wind uplift of a solar panel increases when there is an increase in inclined angle and the clearance above ground shows an opposite effect.

Integrally rigidized acoustic interior spacecraft panel

Science.gov (United States)

1976-01-01

A sandwich panel concept is described which utilizes a monolithic I-beam design as the core. The core and skins are integrally bonded with thermosetting resin into a homogeneous structure. In addition to possessing a high strength to weight ratio, the panel resists combustion, delamination, aging due to fatigue, localized stresses, and exhibits good acoustic properties. Since the panel concept has definite potential as a high flame retardant and low smoke emission panel with excellent structural integrity, aerospace materials were used to optimize the construction for highly demanding space shuttle applications. The specific materials of construction were chosen for low flammability and off-gassing properties as well as for strength, light weight, and sound dampening.

Matlab Software for Spatial Panels

NARCIS (Netherlands)

Elhorst, J.Paul

2014-01-01

Elhorst provides Matlab routines to estimate spatial panel data models at his website. This article extends these routines to include the bias correction procedure proposed by Lee and Yu if the spatial panel data model contains spatial and/or time-period fixed effects, the direct and indirect

Panel 3 - characterization

Energy Technology Data Exchange (ETDEWEB)

Erck, R.A.; Erdemir, A.; Janghsing Hsieh; Lee, R.H.; Xian Zheng Pan; Deming Shu [Argonne National Lab., IL (United States); Feldman, A. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Glass, J.T. [North Carolina State Univ., Raleigh (United States); Kleimer, R. [Coors Ceramics Co., Golden, CO (United States); Lawton, E.A. [JPL/Caltech, Pasadena, CA (United States); McHargue, C.J. [Univ. of Tennessee, Knoxville (United States)

1993-01-01

The task of this panel was to identify and prioritize needs in the area of characterization of diamond and diamond-like-carbon (DLC) films for use in the transportation industry. Until recent advances in production of inexpensive films of diamonds and DLC, it was not feasible that these materials could be mass produced. The Characterization Panel is restricting itself to identifying needs in areas that would be most useful to manufacturers and users in producing and utilizing diamond and DLC coatings in industry. These characterization needs include in-situ monitoring during growth, relation of structure to performance, and standards and definitions.

Development of panel loudspeaker system: design, evaluation and enhancement.

Science.gov (United States)

Bai, M R; Huang, T

2001-06-01

Panel speakers are investigated in terms of structural vibration and acoustic radiation. A panel speaker primarily consists of a panel and an inertia exciter. Contrary to conventional speakers, flexural resonance is encouraged such that the panel vibrates as randomly as possible. Simulation tools are developed to facilitate system integration of panel speakers. In particular, electro-mechanical analogy, finite element analysis, and fast Fourier transform are employed to predict panel vibration and the acoustic radiation. Design procedures are also summarized. In order to compare the panel speakers with the conventional speakers, experimental investigations were undertaken to evaluate frequency response, directional response, sensitivity, efficiency, and harmonic distortion of both speakers. The results revealed that the panel speakers suffered from a problem of sensitivity and efficiency. To alleviate the problem, a woofer using electronic compensation based on H2 model matching principle is utilized to supplement the bass response. As indicated in the result, significant improvement over the panel speaker alone was achieved by using the combined panel-woofer system.

Flat panel detectors - closing the (digital) gap in chest and skeletal radiology

International Nuclear Information System (INIS)

Reiff, Kurt J.

1999-01-01

In the radiological department today the majority of all X-ray procedures on chest and skeletal radiography is performed with classical film-screen-systems. Using digital luminescence radiography (DLR or CR, which stands for Computed Radiography) as a technique has shown a way to replace this 100-year-old procedure of doing general radiography work by acquiring the X-rays digitally via phosphor screens, but this approach has faced criticism from lots of radiologists world wide and therefore has not been widely accepted except in the intensive care environment. A new technology is now rising based on the use of so called flat panel X-ray (FD) detectors. Semi-conducting material detects the X-rays in digital form directly and creates an instantaneous image for display, distribution and diagnosis. This ability combined with a large field of view and -- compared to existing methods -- excellent detective quantum efficiency represents a revolutionary step for chest and skeletal radiography and will put basic X-ray-work back into the focus of radiological solutions. This paper will explain the basic technology of flat panel detectors, possible system solutions based on this new technology, aspects of the user interface influencing the system utilization and versatility as well as the possibility to redefine the patient examination process for chest and skeletal radiography. Furthermore the author discusses limitations for the first released systems, upgrades for the installed base and possible scenarios for the future. e.g. fluoroscopy or angiography application

Auditory-Verbal Music Play Therapy: An Integrated Approach (AVMPT

Directory of Open Access Journals (Sweden)

Sahar Mohammad Esmaeilzadeh

2013-10-01

Full Text Available Introduction: Hearing loss occurs when there is a problem with one or more parts of the ear or ears and causes children to have a delay in the language-learning process. Hearing loss affects children's lives and their development. Several approaches have been developed over recent decades to help hearing-impaired children develop language skills. Auditory-verbal therapy (AVT is one such approach. Recently, researchers have found that music and play have a considerable effect on the communication skills of children, leading to the development of music therapy (MT and play therapy (PT. There have been several studies which focus on the impact of music on hearing-impaired children. The aim of this article is to review studies conducted in AVT, MT, and PT and their efficacy in hearing-impaired children. Furthermore, the authors aim to introduce an integrated approach of AVT, MT, and PT which facilitates language and communication skills in hearing-impaired children.   Materials and Methods: In this article we review studies of AVT, MT, and PT and their impact on hearing-impaired children. To achieve this goal, we searched databases and journals including Elsevier, Chor Teach, and Military Psychology, for example. We also used reliable websites such as American Choral Directors Association and Joint Committee on Infant Hearing websites. The websites were reviewed and key words in this article used to find appropriate references. Those articles which are related to ours in content were selected.    Results: Recent technologies have brought about great advancement in the field of hearing disorders. Now these impairments can be detected at birth, and in the majority of cases, hearing impaired children can develop fluent spoken language through audition. According to researches on the relationship between hearing impaired children’s communication and language skills and different approaches of therapy, it is known that learning through listening and

Natural Stabilized Earth Panels versus Conventional Façade Systems. Economic and Environmental Impact Assessment

Directory of Open Access Journals (Sweden)

Carmen Galán-Marín

2018-03-01

Full Text Available More effective construction technologies are needed nowadays in order to reduce construction energy consumption during the life-cycle of buildings. Besides which, it is necessary to consider the economic feasibility and associated costs within the framework of these alternative technologies so as to favouring their practical implementation in the construction sector. In this sense, this paper presents an economic and environmental comparison of a new non-bearing façade construction solution based on the extruded unfired stabilized clay panels as opposed to three traditional solutions with similar physical, thermal, and aesthetic characteristics in terms of the exterior cladding. The proposed panels are a sandwich type configuration with an intermediate insulating material and two exterior pieces manufactured by extrusion with raw earth stabilized with alginate and animal wool fibers. In this paper, details of the constructive technology of the system are provided. From the results obtained, it is possible to conclude that the solution is a valid alternative from the environmental point of view, considerably reducing the Global Warming Potential and the Cumulative Energy Demand. And although the environmental improvement of the system can be considered the primary objective of this investigation, on the other hand, once executed, it will also be a competitive constructive technology from the perspective of the system’s final costs.

Face-Sheet Quality Analysis and Thermo-Physical Property Characterization of OOA and Autoclave Panels

Science.gov (United States)

Miller, Sandi G.; Lort, Richard D., III; Zimmerman, Thomas J.; Sutter, James K.; Pelham, Larry I.; McCorkle, Linda S.; Scheiman, Daniel A.

2012-01-01

Increased application of polymer matrix composite (PMC) materials in large vehicle structures requires consideration of non-autoclave manufacturing technology. The NASA Composites for Exploration project, and its predecessor, Lightweight Spacecraft Structures and Materials project, were tasked with the development of materials and manufacturing processes for structures that will perform in a heavy-lift-launch vehicle environment. Both autoclave and out of autoclave processable materials were considered. Large PMC structures envisioned for such a vehicle included the payload shroud and the interstage connector. In this study, composite sandwich panels representing 1/16th segments of the barrel section of the Ares V rocket fairing were prepared as 1.8 m x 2.4 m sections of the 10 m diameter arc segment. IM7/977-3 was used as the face-sheet prepreg of the autoclave processed panels and T40-800B/5320-1 for the out of autoclave panels. The core was 49.7 kg/sq m (3.1 lb/cu ft (pcf)) aluminum honeycomb. Face-sheets were fabricated by automated tape laying 153 mm wide unidirectional tape. This work details analysis of the manufactured panels where face-sheet quality was characterized by optical microscopy, cured ply thickness measurements, acid digestion, and thermal analysis.

Solar Panel Installations on Existing Structures

OpenAIRE

Tim D. Sass; Pe; Leed

2013-01-01

The rising price of fossil fuels, government incentives and growing public aware-ness for the need to implement sustainable energy supplies has resulted in a large in-crease in solar panel installations across the country. For many sites the most eco-nomical solar panel installation uses existing, southerly facing rooftops. Adding solar panels to an existing roof typically means increased loads that must be borne by the building-s structural elements. The structural desig...

Results of water corrosion in static cell tests representing multi-metal assemblies in the hydraulic circuits of Tore supra

Energy Technology Data Exchange (ETDEWEB)

Lipa, M. [CEA/DSM/DRFC Centre de Cadarache, 13 - Saint-Paul lez Durance (France); Blanchet, J.; Cellier, F. [Framatome, 71 - Saint Marcel (France). Centre Technique

2007-07-01

Following experiences obtained with steam generator tubes of nuclear power plants, a cooling water quality of AVT (all volatile treatment) has been defined based on demineralised water with adjustment of the pH value to about 9.0/7.0 (25 C/200 C) by addiction of ammoniac, and hydrazine in order to absorb oxygen dissolved in water. At that time, a simplified water corrosion test program has been performed using static (no circulation) test cell samples made of above mentioned TS metal combinations. All test cell samples, prepared and filled with AVT water, were performed at 280 C and 65 bars in an autoclave during 3000 hours. The test cell water temperature has been chosen to be sufficient above the TS component working temperature, in order to accelerate an eventual corrosion process. Generally all above mentioned metal combinations survived the test campaign without stress corrosion cracking, with the exception of the memory metal junction (creep in Cu) and the bellows made of St-St 316L and Inconel 625 while 316 Ti bellows survived. In contrary to the vacuum brazed Cu-LSTP to St-St samples, some of flame brazed Cu to St-St samples failed either in the braze joint or in the copper structure itself. For comparison, a spot weld of an inflated 316L panel sample, filled voluntary with a caustic solution of pH 11.5 (25 C), failed after 90 h of testing (intergranular cracking at the spot weld), while an identical sample containing AVT water of pH 9.0 (25 C) survived without damage. The results of these tests, performed during 1986 and 1997, have never been published and therefore are presented more in detail in this paper since corrosion in hydraulic circuits is also an issue of ITER. Up to day, the TS cooling water plant operates with an above mentioned water treatment and no water leaks have been detected on in-vessel components originating from water corrosion at high temperature and high pressure. (orig.)

Results of water corrosion in static cell tests representing multi-metal assemblies in the hydraulic circuits of Tore supra

International Nuclear Information System (INIS)

Lipa, M.; Blanchet, J.; Cellier, F.

2007-01-01

Following experiences obtained with steam generator tubes of nuclear power plants, a cooling water quality of AVT (all volatile treatment) has been defined based on demineralised water with adjustment of the pH value to about 9.0/7.0 (25 C/200 C) by addiction of ammoniac, and hydrazine in order to absorb oxygen dissolved in water. At that time, a simplified water corrosion test program has been performed using static (no circulation) test cell samples made of above mentioned TS metal combinations. All test cell samples, prepared and filled with AVT water, were performed at 280 C and 65 bars in an autoclave during 3000 hours. The test cell water temperature has been chosen to be sufficient above the TS component working temperature, in order to accelerate an eventual corrosion process. Generally all above mentioned metal combinations survived the test campaign without stress corrosion cracking, with the exception of the memory metal junction (creep in Cu) and the bellows made of St-St 316L and Inconel 625 while 316 Ti bellows survived. In contrary to the vacuum brazed Cu-LSTP to St-St samples, some of flame brazed Cu to St-St samples failed either in the braze joint or in the copper structure itself. For comparison, a spot weld of an inflated 316L panel sample, filled voluntary with a caustic solution of pH 11.5 (25 C), failed after 90 h of testing (intergranular cracking at the spot weld), while an identical sample containing AVT water of pH 9.0 (25 C) survived without damage. The results of these tests, performed during 1986 and 1997, have never been published and therefore are presented more in detail in this paper since corrosion in hydraulic circuits is also an issue of ITER. Up to day, the TS cooling water plant operates with an above mentioned water treatment and no water leaks have been detected on in-vessel components originating from water corrosion at high temperature and high pressure. (orig.)

78 FR 63501 - Meetings of Humanities Panel

Science.gov (United States)

2013-10-24

... NATIONAL FOUNDATION ON THE ARTS AND THE HUMANITIES Meetings of Humanities Panel AGENCY: National Endowment for the Humanities. ACTION: Notice of meetings. SUMMARY: Pursuant to section 10(a)(2) of the... Humanities Panel will be held during November, 2013 as follows. The purpose of the meetings is for panel...

Uncertainties in predicting solar panel power output

Science.gov (United States)

Anspaugh, B.

1974-01-01

The problem of calculating solar panel power output at launch and during a space mission is considered. The major sources of uncertainty and error in predicting the post launch electrical performance of the panel are considered. A general discussion of error analysis is given. Examples of uncertainty calculations are included. A general method of calculating the effect on the panel of various degrading environments is presented, with references supplied for specific methods. A technique for sizing a solar panel for a required mission power profile is developed.

Additive manufacturing of ITER first wall panel parts by two approaches: Selective laser melting and electron beam melting

International Nuclear Information System (INIS)

Zhong, Yuan; Rännar, Lars-Erik; Wikman, Stefan; Koptyug, Andrey; Liu, Leifeng; Cui, Daqing; Shen, Zhijian

2017-01-01

Highlights: • A novel way using additive manufacturing to fabricated ITER First Wall Panel parts is proposed. • ITER First Wall Panel parts successfully manufactured by both SLM and EBM are compared. • Physical and mechanical properties of SLM and EBM SS316L are clearly compared. • Problems encountered for large scale part building were discussed and possible solutions are given. - Abstract: Fabrication of ITER First Wall (FW) Panel parts by two additive manufacturing (AM) technologies, selective laser melting (SLM) and electron beam melting (EBM), was supported by Fusion for Energy (F4E). For the first time, AM is applied to manufacture ITER In-Vessel parts with complex design. Fully dense SS316L was prepared by both SLM and EBM after developing optimized laser/electron beam parameters. Characterizations on the density, magnetic permeability, microstructure, defects and inclusions were carried out. Tensile properties, Charpy-impact properties and fatigue properties of SLM and EBM SS316L were also compared. ITER FW Panel parts were successfully fabricated by both SLM and EBM in a one-step building process. The SLM part has smoother surface, better size accuracy while the EBM part takes much less time to build. Issues with removing support structures might be solved by slightly changing the design of the internal cooling system. Further investigation of the influence of neutron irradiation on materials properties between the two AM technologies is needed.

Additive manufacturing of ITER first wall panel parts by two approaches: Selective laser melting and electron beam melting

Energy Technology Data Exchange (ETDEWEB)

Zhong, Yuan [Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, SE-106 91 Stockholm (Sweden); Rännar, Lars-Erik [Department of Quality Technology, Mechanical Engineering and Mathematics, Sports Tech Research Centre, Mid Sweden University, SE-831 25 Östersund (Sweden); Wikman, Stefan [Fusion for Energy, Torres Diagonal Litoral B3, Josep Pla 2, 08019 Barcelona (Spain); Koptyug, Andrey [Department of Quality Technology, Mechanical Engineering and Mathematics, Sports Tech Research Centre, Mid Sweden University, SE-831 25 Östersund (Sweden); Liu, Leifeng; Cui, Daqing [Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, SE-106 91 Stockholm (Sweden); Shen, Zhijian, E-mail: shen@mmk.su.se [Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, SE-106 91 Stockholm (Sweden)

2017-03-15

Highlights: • A novel way using additive manufacturing to fabricated ITER First Wall Panel parts is proposed. • ITER First Wall Panel parts successfully manufactured by both SLM and EBM are compared. • Physical and mechanical properties of SLM and EBM SS316L are clearly compared. • Problems encountered for large scale part building were discussed and possible solutions are given. - Abstract: Fabrication of ITER First Wall (FW) Panel parts by two additive manufacturing (AM) technologies, selective laser melting (SLM) and electron beam melting (EBM), was supported by Fusion for Energy (F4E). For the first time, AM is applied to manufacture ITER In-Vessel parts with complex design. Fully dense SS316L was prepared by both SLM and EBM after developing optimized laser/electron beam parameters. Characterizations on the density, magnetic permeability, microstructure, defects and inclusions were carried out. Tensile properties, Charpy-impact properties and fatigue properties of SLM and EBM SS316L were also compared. ITER FW Panel parts were successfully fabricated by both SLM and EBM in a one-step building process. The SLM part has smoother surface, better size accuracy while the EBM part takes much less time to build. Issues with removing support structures might be solved by slightly changing the design of the internal cooling system. Further investigation of the influence of neutron irradiation on materials properties between the two AM technologies is needed.

Sound-proof Sandwich Panel Design via Metamaterial Concept

Science.gov (United States)

Sui, Ni

Sandwich panels consisting of hollow core cells and two face-sheets bonded on both sides have been widely used as lightweight and strong structures in practical engineering applications, but with poor acoustic performance especially at low frequency regime. Basic sound-proof methods for the sandwich panel design are spontaneously categorized as sound insulation and sound absorption. Motivated by metamaterial concept, this dissertation presents two sandwich panel designs without sacrificing weight or size penalty: A lightweight yet sound-proof honeycomb acoustic metamateiral can be used as core material for honeycomb sandwich panels to block sound and break the mass law to realize minimum sound transmission; the other sandwich panel design is based on coupled Helmholtz resonators and can achieve perfect sound absorption without sound reflection. Based on the honeycomb sandwich panel, the mechanical properties of the honeycomb core structure were studied first. By incorporating a thin membrane on top of each honeycomb core, the traditional honeycomb core turns into honeycomb acoustic metamaterial. The basic theory for such kind of membrane-type acoustic metamaterial is demonstrated by a lumped model with infinite periodic oscillator system, and the negative dynamic effective mass density for clamped membrane is analyzed under the membrane resonance condition. Evanescent wave mode caused by negative dynamic effective mass density and impedance methods are utilized to interpret the physical phenomenon of honeycomb acoustic metamaterials at resonance. The honeycomb metamaterials can extraordinarily improve low-frequency sound transmission loss below the first resonant frequency of the membrane. The property of the membrane, the tension of the membrane and the numbers of attached membranes can impact the sound transmission loss, which are observed by numerical simulations and validated by experiments. The sandwich panel which incorporates the honeycomb metamateiral as

Home is where the future is: The BrightFocus Foundation consensus panel on dementia care.

Science.gov (United States)

Samus, Quincy M; Black, Betty Smith; Bovenkamp, Diane; Buckley, Michael; Callahan, Christopher; Davis, Karen; Gitlin, Laura N; Hodgson, Nancy; Johnston, Deirdre; Kales, Helen C; Karel, Michele; Kenney, John Jay; Ling, Shari M; Panchal, Maï; Reuland, Melissa; Willink, Amber; Lyketsos, Constantine G

2018-01-01

A national consensus panel was convened to develop recommendations on future directions for home-based dementia care (HBDC). The panel summarized advantages and challenges of shifting to HBDC as the nexus of care and developed consensus-based recommendations. The panel developed five core recommendations: (1) HBDC should be considered the nexus of new dementia models, from diagnosis to end of life in dementia; (2) new payment models are needed to support HBDC and reward integration of care; (3) a diverse new workforce that spans the care continuum should be prepared urgently; (4) new technologies to promote communication, monitoring/safety, and symptoms management must be tested, integrated, and deployed; and (5) targeted dissemination efforts for HBDC must be employed. HBDC represents a promising paradigm shift to improve care for those living with dementia and their family caregivers: these recommendations provide a framework to chart a course forward for HBDC. Copyright © 2017 the Alzheimer's Association. All rights reserved.

Thermal Analysis of Solar Panels

Science.gov (United States)

Barth, Nicolas; de Correia, João Pedro Magalhães; Ahzi, Saïd; Khaleel, Mohammad Ahmed

In this work, we propose to analyze the thermal behavior of PV panels using finite element simulations (FEM). We applied this analysis to compute the temperature distribution in a PV panel BP 350 subjected to different atmospheric conditions. This analysis takes into account existing formulations in the literature and, based on NOCT conditions, meteorological data was used to validate our approach for different wind speed and solar irradiance. The electrical performance of the PV panel was also studied. The proposed 2D FEM analysis is applied to different region's climates and was also used to consider the role of thermal inertia on the optimization of the PV device efficiency.

Vehicle Technology for Civil Aviation: The Seventies and Beyond

Science.gov (United States)

1972-01-01

The panel discussion on aviation technology for the seventies and beyond is reported. Topics discussed include: Government role in developing and applying new aeronautical technologies, noise and environmental problems, and congestion in the vicinity of major air terminals.

78 FR 74175 - Meetings of Humanities Panel

Science.gov (United States)

2013-12-10

... NATIONAL FOUNDATION ON THE ARTS AND THE HUMANITIES Meetings of Humanities Panel AGENCY: National Endowment for the Humanities. ACTION: Notice of meetings. SUMMARY: Pursuant to section 10(a)(2) of the... Humanities Panel will be held during January 2014 as follows. The purpose of the meetings is for panel review...

32 CFR 724.104 - NDRB Traveling Panel.

Science.gov (United States)

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false NDRB Traveling Panel. 724.104 Section 724.104 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY PERSONNEL NAVAL DISCHARGE REVIEW BOARD Definitions § 724.104 NDRB Traveling Panel. An NDRB Panel that travels for the purpose of...

Precast concrete sandwich panels subjected to impact loading

Science.gov (United States)

Runge, Matthew W.

Precast concrete sandwich panels are a relatively new product in the construction industry. The design of these panels incorporates properties that allow for great resilience against temperature fluctuation as well as the very rapid and precise construction of facilities. The concrete sandwich panels investigated in this study represent the second generation of an ongoing research and development project. This second generation of panels have been engineered to construct midsized commercial buildings up to three stories in height as well as residential dwellings. The panels consist of a double-tee structural wythe, a foam core and a fascia wythe, joined by shear connectors. Structures constructed from these panels may be subjected to extreme loading including the effects of seismic and blast loading in addition to wind. The aim of this work was to investigate the behaviour of this particular sandwich panel when subjected to structural impact events. The experimental program consisted of fourteen concrete sandwich panels, five of which were considered full-sized specimens (2700 mm X 1200mm X 270 mm) and nine half-sized specimens (2700mm X 600mm X 270 mm) The panels were subjected to impact loads from a pendulum impact hammer where the total energy applied to the panels was varied by changing the mass of the hammer. The applied loads, displacements, accelerations, and strains at the mid-span of the panel as well as the reaction point forces were monitored during the impact. The behaviour of the panels was determined primarily from the experimental results. The applied loads at low energy levels that caused little to no residual deflection as well as the applied loads at high energy levels that represent catastrophic events and thus caused immediate failure were determined from an impact on the structural and the fascia wythes. Applied loads at intermediate energy levels representing extreme events were also used to determine whether or not the panels could withstand

Case Study - Monitoring the Photovoltaic Panels

OpenAIRE

PACURAR Ana Talida; TOADER Dumitru; PACURAR Cristian

2014-01-01

The photovoltaic cell represents one of the most dynamic and attractive way to converts renewable energy sources in electricity production. That means to convert solar energy into electricity. In this paper is presented a analogy between two types of photovoltaic panels installed, with educational role for students. Also the objective of this paper is to estimate the performance of photovoltaic panels and to provide the best solution for industry. These two types of photovoltaic panels wer...

El Salvador - Rural Electrification - Solar Panels

Data.gov (United States)

Millennium Challenge Corporation — This is a summative qualitative performance evaluation (PE) of the solar panel component of the solar panel component of the RE Sub-Activity. The final report will...

Experimental investigations into in-plane stiffness and strength of steel frames with precast concrete infill panels

NARCIS (Netherlands)

Hoenderkamp, J.C.D.; Hofmeyer, H.; Snijder, H.H.; Richard Liew, J.; Choo, Y.S.

2007-01-01

At Eindhoven University of Technology a research program on composite construction is underway aiming at the development of design rules for steel frames with precast concrete infill panels subject to horizontal loading. In two projects, 3 by 3 m steel frames are infilled with concrete: solid

Daytime space cooling with phase change material ceiling panels discharged using rooftop photovoltaic/thermal panels and night-time ventilation

DEFF Research Database (Denmark)

Bourdakis, Eleftherios; Pean, Thibault Quentin; Gennari, Luca

2016-01-01

The possibility of using photovoltaic/thermal panels for producing cold water through the process of night-time radiative cooling was experimentally examined. The cold water was used to discharge phase change material in ceiling panels in a climatic chamber. Both night-time radiative cooling...... the photovoltaic/thermal varied from 56% to 122%. The phase change material ceiling panels were thus, capable of providing an acceptable thermal environment and the photovoltaic/thermal panels were able to provide most of the required electricity and cold water needed for cooling....

7 CFR 205.509 - Peer review panel.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Peer review panel. 205.509 Section 205.509 Agriculture... PROVISIONS NATIONAL ORGANIC PROGRAM Accreditation of Certifying Agents § 205.509 Peer review panel. The Administrator shall establish a peer review panel pursuant to the Federal Advisory Committee Act (FACA) (5 U.S.C...

A novel AOI system for OLED panel inspection

International Nuclear Information System (INIS)

Perng, D B; Chen, Y C; Lee, M K

2005-01-01

Organic light emitting diode (OLED) technology uses substances that emit red, green, blue or white light. An OLED panel consists of stacks of several thin layers of different materials, as such it is not easy to inspect the common OLED defects. In this paper, an autooptical inspection (AOI) system which can detect such defects effectively and robustly was proposed and developed. The proposed system can also identify, in which layer the defect occurred. Meanwhile, a moving mechanism coupled with a lighting mechanism was proposed and implemented for grabbing clear images. The proposed AOI system would provide great help in improving the OLED production process and the quality control process

Advanced water chemistry management in power plants

International Nuclear Information System (INIS)

Regis, V.; Sigon, F.

1995-01-01

Advanced water management based on low external impact cycle chemistry technologies and processes, effective on-line water control and monitoring, has been verified to improve water utilization and to reduce plant liquid supply and discharge. Simulations have been performed to optimize system configurations and performances, with reference to a 4 x 320 MWe/once-through boiler/AVT/river cooled power plant, to assess the effectiveness of membrane separation technologies allowing waste water reuse, to enhance water management system design and to compare these solutions on a cost/benefit analysis. 6 refs., 3 figs., 3 tabs

Performance analysis of PV panel under varying surface temperature

Directory of Open Access Journals (Sweden)

Kumar Tripathi Abhishek

2018-01-01

Full Text Available The surface temperature of PV panel has an adverse impact on its performance. The several electrical parameters of PV panel, such as open circuit voltage, short circuit current, power output and fill factor depends on the surface temperature of PV panel. In the present study, an experimental work was carried out to investigate the influence of PV panel surface temperature on its electrical parameters. The results obtained from this experimental study show a significant reduction in the performance of PV panel with an increase in panel surface temperature. A 5W PV panel experienced a 0.4% decrease in open circuit voltage for every 1°C increase in panel surface temperature. Similarly, there was 0.6% and 0.32% decrease in maximum power output and in fill factor, respectively, for every 1°C increase in panel surface temperature. On the other hand, the short circuit current increases with the increase in surface temperature at the rate of 0.09%/°C.

Differing professional opinions: 1987 special review panel

International Nuclear Information System (INIS)

1988-01-01

In November 1987, the five-member Differing Professional Opinions Special Review Panel established by the Executive Director for Operations of the US Nuclear Regulatory Commission to review agency policies and procedures for handling differing professional opinions (DPOs) presented its findings and recommendations in NUREG-1290. The issuance of that report completed the first task of the panel's charter. In accordance with Manual chapter 4125, Section L, and the charter of the Special Review Panel, the panel's second task was to ''...review...the DPOs submitted subsequent to the previous Panel's review, in order to identify any employee whose DPO made a significant contribution to the Agency or to the public safety but who has not yet been recognized for such contribution.'' This Addendum provides the findings of that review

Photoelectric panel with equatorial mounting of drive

Science.gov (United States)

Kukhta, M. S.; Krauinsh, P. Y.; Krauinsh, D. P.; Sokolov, A. P.; Mainy, S. B.

2018-03-01

The relevance of the work is determined by the need to create effective models for sunny energy. The article considers a photoelectric panel equipped with a system for tracking the sun. Efficiency of the system is provided by equatorial mounting, which compensates for the rotation of the Earth by rotating the sunny panel in the plane of the celestial equator. The specificity of climatic and geographical conditions of Tomsk is estimated. The dynamics of power variations of photoelectric panels with equatorial mounting during seasonal fluctuations in Tomsk is calculated. A mobile photovoltaic panel with equatorial mounting of the drive has been developed. The methods of design strategy for placing photovoltaic panels in the architectural environment of the city are presented. Key words: sunny energy, photovoltaics, equatorial mounting, mechatronic model, wave reducer, electric drive.

Retaining Ring Fastener for Solar Panels

Science.gov (United States)

Wilson, A. H.

1983-01-01

Simple articulating linkage secures solar panels into supporting framework. Five element linkage collapses into W-shape for easy placement into framework, then expands to form rectangle of same dimensions as those of panel.

Lipid Panel

Science.gov (United States)

... A routine cardiac risk assessment typically includes a fasting lipid panel. Beyond that, research continues into the usefulness of other non-traditional markers of cardiac risk, such as Lp-PLA 2 . A health practitioner may choose to evaluate one or more ...

Characterization and localization of arginine vasotocin receptors in the brain and kidney of an amphibian

International Nuclear Information System (INIS)

Boyd, S.K.

1987-01-01

Because arginine vasotocin (AVT) activates male sexual behaviors in the rough-skinned newt (Taricha granulosa), quantitative autoradiography with radiolabeled arginine vasopressin ( 3 H-AVP) was used to localize and characterize putative AVT receptors in the brain of this amphibian. Binding of 3 H-AVP to sites within the medial pallium was saturable, specific, reversible, of high affinity and low capacity. These binding sites appear to represent authentic central nervous system receptors for AVT. Furthermore, ligand specificity for the binding sites in this amphibian differs from that reported for AVP binding sites in rat brains. Dense concentrations of specific binding sites were located in the olfactory nerve as it entered the olfactory bulb within the medial pallium, dorsal pallium, and amygdala pars lateralis of the telencephalon, and in the tegmental region of the medulla. Concentrations of binding sites differed significantly among various brain regions. A comparison of male and female newts collected during the breeding season revealed no sexual dimorphism. These areas may represent site(s) of action where AVT elicits sexual behaviors in male T. granulosa

The CRRES high efficiency solar panel

International Nuclear Information System (INIS)

Trumble, T.M.

1991-01-01

This paper reports on the High Efficiency Solar Panel (HESP) experiments which is to provide both engineering and scientific information concerning the effects of space radiation on advanced gallium arsenide (GaAs) solar cells. The HESP experiment consists of an ambient panel, and annealing panel and a programmable load. This experiment, in conjunction with the radiation measurement experiments abroad the CREES, provides the first opportunity to simultaneously measure the trapped radiation belts and the results of radiation damage to solar cells. The engineering information will result in a design guide for selecting the optimum solar array characteristics for different orbits and different lifetimes. The scientific information will provide both correlation of laboratory damage effects to space damage effects and a better model for predicting effective solar cell panel lifetimes

Design and optical analyses of an arrayed microfluidic tunable prism panel for enhancing solar energy collection

International Nuclear Information System (INIS)

Narasimhan, Vinayak; Jiang, Dongyue; Park, Sung-Yong

2016-01-01

Highlights: • We present an arrayed tunable prism panel enabling wide tracking and high solar concentration. • A microfluidic technology allows a low-cost, lightweight and precise solar tracking system. • Our prism panel enables high solar concentration up to 2032× factor. • Various liquid prism configurations (stacked prism arrays) and optical materials are considered. • Their impacts on solar beam steering, reflection losses and beam concentration are studied. - Abstract: We present the design and optical analyses of an arrayed microfluidic tunable prism panel that enables wide solar tracking and high solar concentration while minimizing energy loss. Each of the liquid prism modules is implemented by a microfluidic (i.e. non-mechanical) technology based on electrowetting for adaptive solar beam steering. Therefore the proposed platform offers a low-cost, lightweight and precise solar tracking system while obviating the need for bulky and heavy mechanical moving parts essentially required for a conventional motor-driven solar tracker. In this paper, various liquid prism configurations in terms of design (single, double, triple and quad-stacked prism arrays) as well as optical materials are considered and their impact on optical performance aspects such as solar beam steering, reflection losses and beam concentration is studied. Our system is able to achieve a wide solar tracking covering the whole-day movement of the Sun and a reflection loss below 4.4% with a Rayleigh’s film for a quad-stacked prism configuration. Furthermore, an arrayed prism panel is proposed to increase the aperture area and thus allows for the collection of large amounts of sunlight. Our simulation study based on the optical design software, ZEMAX, indicates that the prism panel is capable of high solar concentration up to 2032× factor even without conventional solar tracking devices. We also deal with dispersion characteristics of the materials and their corresponding effect on

The irradiance and temperature dependent mathematical model for estimation of photovoltaic panel performances

International Nuclear Information System (INIS)

Barukčić, M.; Ćorluka, V.; Miklošević, K.

2015-01-01

Highlights: • The temperature and irradiance dependent model for the I–V curve estimation is presented. • The purely mathematical model based on the analysis of the I–V curve shape is presented. • The model includes the Gompertz function with temperature and irradiance dependent parameters. • The input data are extracted from the data sheet I–V curves. - Abstract: The temperature and irradiance dependent mathematical model for photovoltaic panel performances estimation is proposed in the paper. The base of the model is the mathematical function of the photovoltaic panel current–voltage curve. The model of the current–voltage curve is based on the sigmoid function with temperature and irradiance dependent parameters. The temperature and irradiance dependencies of the parameters are proposed in the form of analytic functions. The constant parameters are involved in the analytical functions. The constant parameters need to be estimated to get the temperature and irradiance dependent current–voltage curve. The mathematical model contains 12 constant parameters and they are estimated by using the evolutionary algorithm. The optimization problem is defined for this purpose. The optimization problem objective function is based on estimated and extracted (measured) current and voltage values. The current and voltage values are extracted from current–voltage curves given in datasheet of the photovoltaic panels. The new procedure for estimation of open circuit voltage value at any temperature and irradiance is proposed in the model. The performance of the proposed mathematical model is presented for three different photovoltaic panel technologies. The simulation results indicate that the proposed mathematical model is acceptable for estimation of temperature and irradiance dependent current–voltage curve and photovoltaic panel performances within temperature and irradiance ranges

Structure, Mechanism, and Application of Vacuum Insulation Panels in Chinese Buildings

Directory of Open Access Journals (Sweden)

Changhai Peng

2016-01-01

Full Text Available Thermal insulation is one of the most used approaches to reduce energy consumption in buildings. Vacuum insulation panels (VIPs are new thermal insulation materials that have been used in the domestic and overseas market in the last 20 years. Due to the vacuum thermal insulation technology of these new materials, their thermal conductivity can be as low as 0.004 W/(m·K at the center of panels. In addition, VIPs that are composites with inorganic core and an envelope out of commonly three metallized PET layers and a PE sealing layer can provide B class fire resistance (their core materials are not flammable and are classified as A1. Compared with other conventional thermal insulation materials, the thermal insulation and fire resistance performances form the foundation of VIP’s applications in the construction industry. The structure and thermal insulation mechanism of VIP and their application potential and problems in Chinese buildings are described in detail.

A chemometrics study of analytical panels in virgin olive oil. An approach for evaluating panels in training

Directory of Open Access Journals (Sweden)

Aparicio, R.

1991-06-01

Full Text Available A mathematical procedure including Canonical Correlation, Factor and cluster analysis and Multiple Regression was designed to study whether two different sensory panels, with different levels of training, could be considered as a unity. Among others, correlations between each attribute of both panels, matrices of partial correlations, variance explained by the most important factors and similarity among clusters were computed as the procedure to evaluate if a Panel in training works as well as an expertise. In addition, every one of the factors was correlated with the final evaluation of quality for analyzing the interrelationship between the profile notes and the grading table of virgin olive oil quality from a mathematical point of view. Finally, a stepwise multiple correlation analyzes how the panels modeled the evaluated samples. Promising directions for future research are also suggested.

Un procedimiento matemático que incluye Correlación Canónica, Análisis Factorial y de "clusters", y Regresión Múltiple fue diseñado para estudiar si dos paneles analíticos, con diferentes niveles de entrenamiento, podrían ser considerados idénticos. Para evaluar si un panel en o después de un entrenamiento opera tan bien como uno experto, se analizaron las correlaciones entre los atributos de ambos paneles, las matrices de correlaciones parciales, la varianza explicada por los factores más importantes y la similaridad entre los aglomerados ("clusters" entre otras. Además, los tres factores más importantes fueron correlacionados con las valoraciones finales de calidad, para conocer la interrelación entre la hoja de perfil y la tabla de puntuación. Finalmente, un análisis de regresión múltiple permite conocer cómo es el modelo que los paneles han diseñado para muestras de aceite de oliva virgen evaluadas. También se sugieren las tendencias en la investigación futura.

JETC (Japanese Technology Evaluation Center) Panel Report on High Temperature Superconductivity in Japan

Science.gov (United States)

Shelton, Duane; Gamota, George

1989-01-01

The Japanese regard success in R and D in high temperature superconductivity as an important national objective. The results of a detailed evaluation of the current state of Japanese high temperature superconductivity development are provided. The analysis was performed by a panel of technical experts drawn from U.S. industry and academia, and is based on reviews of the relevant literature and visits to Japanese government, academic and industrial laboratories. Detailed appraisals are presented on the following: Basic research; superconducting materials; large scale applications; processing of superconducting materials; superconducting electronics and thin films. In all cases, comparisons are made with the corresponding state-of-the-art in the United States.

Effects of temperature and melatonin on day-night expression patterns of arginine vasotocin and isotocin mRNA in the diencephalon of a temperate wrasse Halichoeres tenuispinis.

Science.gov (United States)

Bouchekioua, Selma; Hur, Sung-Pyo; Takeuchi, Yuki; Lee, Young-Don; Takemura, Akihiro

2018-06-01

Most wrasses are protogynous species that swim to feed, reproduce during the daytime, and bury themselves under the sandy bottom at night. In temperate and subtropical wrasses, low temperature influences emergence from the sandy bottom in the morning, and induces a hibernation-like state in winter. We cloned and characterized the prohormone complementary DNAs (cDNAs) of arginine vasotocin (AVT) and isotocin (IT) in a temperate wrasse (Halichoeres tenuispinis) and examined the effects of day/night and temperature on their expression in the diencephalon, because these neurohypophysial peptides are related to the sex behavior of wrasses. The full-length cDNAs of pro-AVT and pro-IT were 938 base pairs (154 amino acids) and 759 base pairs (156 amino acids) in length, respectively. Both pro-peptides contained a signal sequence followed by the respective hormones and neurophysin connected by a Gly-Lys-Arg bridge. Reverse-transcription polymerase chain reaction (RT-PCR) revealed that pro-AVT mRNA expression was specifically observed in the diencephalon, whereas pro-IT mRNA expression was seen in the whole brain. Quantitative RT-PCR revealed that the mRNA abundance of pro-AVT and pro-IT was higher at midday (zeitgeber time 6; ZT6) than at midnight (ZT18) under 12 h light and 12 h darkness (LD 12:12) conditions, but not under constant light. Intraperitoneal injection of melatonin decreased the mRNA abundance of pro-AVT, but not of pro-IT. When fish were reared under LD 12:12 conditions at 25, 20, and 15 °C, day high and night low mRNA expressions of pro-AVT and pro-IT were maintained. A field survey revealed seasonal variation in the number of swimming fish at observatory sites; many fish emerged from the sandy bottom in summer, but not in winter, suggesting a hibernation-like state under the sandy bottom under low temperature conditions. We conclude that the day-night fluctuation of pro-AVT and pro-IT mRNA abundance in the brain is not affected by temperature and

Effect of water chemistry improvement on flow accelerated corrosion in light-water nuclear reactor

International Nuclear Information System (INIS)

Sugino, Wataru; Ohira, Taku; Nagata, Nobuaki; Abe, Ayumi; Takiguchi, Hideki

2009-01-01

Flow Accelerated Corrosion (FAC) of Carbon Steel (CS) piping has been one of main issues in Light-Water Nuclear Reactor (LWRs). Wall thinning of CS piping due to FAC increases potential risk of pipe rupture and cost for inspection and replacement of damaged pipes. In particular, corrosion products generated by FAC of CS piping brought steam generator (SG) tube corrosion and degradation of thermal performance, when it intruded and accumulated in secondary side of PWR. To preserve SG integrity by suppressing the corrosion of CS, High-AVT chemistry (Feedwater pH9.8±0.2) has been adopted to Tsuruga-2 (1160 MWe PWR, commercial operation in 1987) in July 2005 instead of conventional Low-AVT chemistry (Feedwater pH 9.3). By the High-AVT adoption, the accumulation rate of iron in SG was reduced to one-quarter of that under conventional Low-AVT. As a result, a tendency to degradation of the SG thermal efficiency was improved. On the other hand, it was clarified that High-AVT is ineffective against Flow Accelerated Corrosion (FAC) at the region where the flow turbulence is much larger. By contrast, wall thinning of CS feed water pipes due to FAC has been successfully controlled by oxygen treatment (OT) for long time in BWRs. Because Magnetite film formed on CS surface under AVT chemistry has higher solubility and porosity in comparison with Hematite film, which is formed under OT. In this paper, behavior of the FAC under various pH and dissolved oxygen concentration are discussed based on the actual wall thinning rate of BWR and PWR plant and experimental results by FAC test-loop. And, it is clarified that the FAC is suppressed even under extremely low DO concentration such as 2ppb under AVT condition in PWR. Based on this result, we propose the oxygenated water chemistry (OWC) for PWR secondary system which can mitigate the FAC of CS piping without any adverse effect for the SG integrity. Furthermore, the applicability and effectiveness of this concept developed for FAC

76 FR 62455 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2011-10-07

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (11-088)] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel... Burch, Aerospace Safety Advisory Panel Administrative Officer, National Aeronautics and Space...

78 FR 1265 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2013-01-08

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice 13-001] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel..., Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space Administration...

Panels of microporous insulation

Energy Technology Data Exchange (ETDEWEB)

McWilliams, J.A.; Morgan, D.E.; Jackson, J.D.J.

1990-08-07

Microporous thermal insulation materials have a lattice structure in which the average interstitial dimension is less than the mean free path of the molecules of air or other gas in which the material is arranged. This results in a heat flow which is less than that attributable to the molecular heat diffusion of the gas. According to this invention, a method is provided for manufacturing panels of microporous thermal insulation, in particular such panels in which the insulation material is bonded to a substrate. The method comprises the steps of applying a film of polyvinyl acetate emulsion to a non-porous substrate, and compacting powdery microporous thermal insulation material against the film so as to cause the consolidated insulation material to bond to the substrate and form a panel. The polyvinyl acetate may be applied by brushing or spraying, and is preferably allowed to dry prior to compacting the insulation material. 1 fig.

Design scenarios for flat panel photobioreactors

International Nuclear Information System (INIS)

Slegers, P.M.; Wijffels, R.H.; Straten, G. van; Boxtel, A.J.B. van

2011-01-01

Evaluation of the potential of algae production for biofuel and other products at various locations throughout the world requires assessment of algae productivity under varying light conditions and different reactor layouts. A model was developed to predict algae biomass production in flat panel photobioreactors using the interaction between light and algae growth for the algae species Phaeodactylum tricornutum and Thalassiosira pseudonana. The effect of location, variable sunlight and reactor layout on biomass production in single standing and parallel positioned flat panels was considered. Three latitudes were studied representing the Netherlands, France and Algeria. In single standing reactors the highest yearly biomass production is achieved in Algeria. During the year biomass production fluctuates the most in the Netherlands, while it is almost constant in Algeria. Several combinations of path lengths and biomass concentrations can result in the same optimal biomass production. The productivity in parallel place flat panels is strongly influenced by shading and diffuse light penetration between the panels. Panel orientation has a large effect on productivity and at higher latitudes the difference between north-south and east-west orientation may go up to 50%.

A Panel Cointegration Analysis: Thailand’s International Tourism Demand Model

OpenAIRE

Prasert Chaitip; Chukiat Chaiboonsri

2009-01-01

This paper sought to find the long-run relationships between international tourist arrivals in Thailand and economic variables such as GDP, cost of transportation and exchange rates for the period 1986 to 2007. Also this paper used five standard panel unit root tests such as LLC (2002) panel unit root test, Breitung (2000) panel unit root test, IPS (2003) panel unit root test, Maddala and Wu (1999), Choi (2001) panel unit root test, Handri (1999) panel unit root test. Moreover, the panel coin...

76 FR 19147 - Aerospace Safety Advisory Panel; Meeting.

Science.gov (United States)

2011-04-06

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (11-030)] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announce a forthcoming meeting of the Aerospace Safety Advisory Panel.... Kathy Dakon, Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space...

78 FR 56941 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2013-09-16

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice: 13-114] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel.... Harmony Myers, Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space...

77 FR 25502 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2012-04-30

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (12-030)] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announce a forthcoming meeting of the Aerospace Safety Advisory Panel... FURTHER INFORMATION CONTACT: Ms. Harmony Myers, Aerospace Safety Advisory Panel Executive Director...

77 FR 38090 - Aerospace Safety Advisory Panel; Meeting.

Science.gov (United States)

2012-06-26

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice 12-044] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel.... Harmony Myers, Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space...

75 FR 61219 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2010-10-04

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (10-116)] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel... Dakon, Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space Administration...

77 FR 58413 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2012-09-20

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice 12-074] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announces a forthcoming meeting of the Aerospace Safety Advisory Panel.... Harmony Myers, Aerospace Safety Advisory Panel Executive Director, National Aeronautics and Space...

Photovoltaic Thermal panels in collective thermal solar systems

International Nuclear Information System (INIS)

Elswijk, M.J.; Strootman, K.J.; Jong, M.J.M.; De Lange, E.T.N.; Smit, W.F.

2003-12-01

A feasibility study has been carried out to assess the options to apply photovoltaic/thermal panels (PVT-panels) in collective solar thermal systems in urban areas in the Netherlands. The study was focused on the technical (architecture and installations) and the economical feasibility of collective PVT-systems in comparison with conventional solar thermal systems and combinations of photovoltaic (PV) panels and solar collectors. The results of the study also give insight into cost and the market for PVT-panels. Three case studies in which collective solar collector systems were applied are analyzed again by simulating the installation of a PVT-panels system and a separate solar thermal PV system [nl

75 FR 6407 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2010-02-09

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (10- 020)] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announce a forthcoming meeting of the Aerospace Safety Advisory Panel... FURTHER INFORMATION CONTACT: Ms. Kathy Dakon, Aerospace Safety Advisory Panel Executive Director, National...

Solar Array Panels With Dust-Removal Capability

Science.gov (United States)

Dawson, Stephen; Mardesich, Nick; Spence, Brian; White, Steve

2004-01-01

It has been proposed to incorporate piezoelectric vibrational actuators into the structural supports of solar photovoltaic panels, for the purpose of occasionally inducing vibrations in the panels in order to loosen accumulated dust. Provided that the panels were tilted, the loosened dust would slide off under its own weight. Originally aimed at preventing obscuration of photovoltaic cells by dust accumulating in the Martian environment, the proposal may also offer an option for the design of solar photovoltaic panels for unattended operation at remote locations on Earth. The figure depicts a typical lightweight solar photovoltaic panel comprising a backside grid of structural spars that support a thin face sheet that, in turn, supports an array of photovoltaic cells on the front side. The backside structure includes node points where several spars intersect. According to the proposal, piezoelectric buzzers would be attached to the node points. The process of designing the panel would be an iterative one that would include computational simulation of the vibrations by use of finite- element analysis to guide the selection of the vibrational frequency of the actuators and the cross sections of the spars to maximize the agitation of dust.

Evaluation of Thin Kevlar-Epoxy Fabric Panels Subjected to Shear Loading

Science.gov (United States)

Baker, Donald J.

1996-01-01

The results of an analytical and experimental investigation of 4-ply Kevlar-49-epoxy panels loaded by in-plane shear are presented. Approximately one-half of the panels are thin-core sandwich panels and the other panels are solid-laminate panels. Selected panels were impacted with an aluminum sphere at a velocity of either 150 or 220 ft/sec. The strength of panels impacted at 150 ft/sec was not reduced when compared to the strength of the undamaged panels, but the strength of panels impacted at 220 ft/sec was reduced by 27 to 40 percent. Results are presented for panels that were cyclically loaded from a load less than the buckling load to a load in the postbuckling load range. The thin-core sandwich panels had a lower fatigue life than the solid panels. The residual strength of the solid and sandwich panels cycled more than one million cycles exceeded the baseline undamaged panel strengths. The effect of hysteresis in the response of the sandwich panels is not significant. Results of a nonlinear finite element analysis conducted for each panel design are presented.

Strong increase of solar panels

International Nuclear Information System (INIS)

Segers, R.; Janssen, S.

2012-01-01

The number of installed solar panels in 2011 has increased again. 40 megawatt of new panels have been installed. This increase is twice as high as the year before. The production of solar power increased to 90 million kWh in 2011 as a result of this expansion. However, the share of solar power in total energy use is still very limited. [nl

78 FR 36793 - Aerospace Safety Advisory Panel; Meeting

Science.gov (United States)

2013-06-19

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice 13-068] Aerospace Safety Advisory Panel... Aeronautics and Space Administration announce a forthcoming meeting of the Aerospace Safety Advisory Panel..., Huntsville, AL 35805 FOR FURTHER INFORMATION CONTACT: Ms. Harmony Myers, Aerospace Safety Advisory Panel...

Improving the efficiency of photovoltaic (PV) panels by oil coating

International Nuclear Information System (INIS)

Abd-Elhady, M.S.; Fouad, M.M.; Khalil, T.

2016-01-01

Highlights: • It is possible to improve the efficiency of PV panels by increasing the amount of light transmitted to the panel. • Coating PV panels by a fine layer of Labovac oil increases the amount of sun light transmitted to the panel. • Coating PV panels by a fine layer of Labovac oil increases the power output of the panel. • Coating PV panels with a layer of Labovac oil has to be applied in cold countries and not in hot regions. - Abstract: The objective of this research is to develop a new technique for improving the efficiency of Photovoltaic (PV) panels. This technique is done by coating the front surface of the PV panel by a fine layer of oil in order to increase the amount of light transmitted to the panel, and consequently its efficiency. Different types of oils are examined, including both mineral oils and natural oils. In case of mineral oils; vacuum pump oil (Labovac oil), engine oil (Mobil oil) and brake oil (Abro oil) are examined, while in case of natural oils; olive and sunflower oils are examined. An experimental setup has been developed to examine the performance of the PV panels as a function of oil coatings. The experimental setup consists of an artificial sun, the PV panel under investigation, a cooling system and a measuring system to measure the performance of the panel. It has been found that coating the PV panel with a fine layer of Labovac oil, ∼1 mm thick, improves the efficiency of the PV panel by more than 20%, and this is due to the high transmissivity of the Labovac oil compared to other oils. However, the Labovac oil has a drawback which is overheating of the panel due to its high transmissivity. Coating of PV panels with a fine layer of Labovac oil should be done only in cold regions, in order to avoid the heating effect that can decrease the power output of PV panels.

Blood Test: Comprehensive Metabolic Panel (CMP)

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Blood Test: Comprehensive Metabolic Panel (CMP) KidsHealth / For Parents / Blood ... de sangre: panel metabólico ampliado What Is a Blood Test? A blood test is when a sample of ...

Maintenance and Durability of the Concrete External Layer of Curtain Walls in Prefabricated Technological Poznan Large Panel System

Science.gov (United States)

Jasiczak, Józef; Girus, Krzysztof

2017-10-01

The issue of usability and durability of large-panel building constructed several decades ago is a subject of an in-depth analysis of many domestic and foreign investments. When considering the durability of specific large-panel system, one should consider, among others, the process of making external walls. The long-term and direct impact of weather conditions on the external layer of curtain walls is significant for the durability of large-panel buildings. For the needs of the presented paper, in 2016, the survey of cracks and a series of other tests of large-panel façade, residential building constructed in 1986, in Poland, in the PLP process system - Rataje was executed. Several hundred large-size, triple-layer curtain-wall slab with a 6-cm, concrete exterior cladding layer anchored using pins and hangers with the load-bearing layer, a 9-cm insulation layer made of mineral wool, and a 21-cm structural layer were surveyed. Significant deviations in thicknesses of particular wall layers were proven. Other significant damages and defects of external layers were found. At the second stage, many tests, both nondestructive and destructive, were conducted. They involved determining mechanical properties of an external layer. The concrete thickness was measured using with a type N Schmidt sclerometer and core samples were taken from this layer in order to mark concrete’s compressive strength. The range of carbonation (by phenolphthalein method) and the actual location and condition of reinforcement were estimated using a ferromagnetic device to determine the condition of the external layer. The diagnosis conducted in such a manner was the verification of necessary repair of the walls and their thermal efficiency improvement while ensuring safe conditions of their operation and modern functional and utility requirements. It should be also emphasized that the method of diagnosing the external walls presented in this paper may be popularized when evaluating such

2013 Bioenergy Technologies Office Peer Review Report

Energy Technology Data Exchange (ETDEWEB)

None, None

2014-02-01

This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2013 U.S. Department of Energy Bioenergy Technologies Office's Peer Review meeting.

A Robust Multifunctional Sandwich Panel Design with Trabecular Structures by the Use of Additive Manufacturing Technology for a New De-Icing System

Directory of Open Access Journals (Sweden)

Carlo Giovanni Ferro

2017-06-01

Full Text Available Anti-ice systems assure a vital on-board function in most aircraft: ice prevention or de-icing is mandatory for all aerodynamic surfaces to preserve their performance, and for all the movable surfaces to allow the proper control of the plane. In this work, a novel multi-functional panel concept which integrates anti-icing directly inside the primary structure is presented. In fact, constructing the core of the sandwich with trabecular non-stochastic cells allows the presence of a heat exchanger directly inside the structure with a savings in weight and an improvement in thermal efficiency. This solution can be realized easily in a single-piece component using Additive Manufacturing (AM technology without the need for joints, gluing, or welding. The objective of this study is to preliminarily investigate the mechanical properties of the core constructed with Selective Laser Melting (SLM; through the Design of Experiment (DOE, different design parameters were varied to understand how they affect the compression behaviour.

OLED Luminaire with Panel Integrated Drivers and Advanced Controls

Energy Technology Data Exchange (ETDEWEB)

Lu, Michael [Acuity Brands Lighting, Inc., Atlanta, GA (United States); Spindler, Jeff [OLEDWorks, Rochester, NY (United States)

2017-01-31

For this DOE award, Acuity Brands Lighting developed a novel OLED luminaire system featuring panel-integrated drivers at each individual OLED panel. The luminaire has a base station that receives user commands and performs AC/DC conversion. A power line communication (PLC) protocol is used to provide both power and digital control to each panel. A 66-panel CanvisTM luminaire using state-of-art OLED panels based on this system was successfully constructed. This is a first demonstration of such a luminaire architecture. It is also the first known implementation of this number of independently addressable nodes with a PLC protocol. This luminaire system architecture has added benefits in the flexibility of using multiple panel vendors for a given product, forward compatibility with future panels, and reduced luminaire wiring complexity and assembly time.

Magnetic evaluation of a solar panel using HTS-SQUID

Energy Technology Data Exchange (ETDEWEB)

Kiwa, Toshihiko, E-mail: kiwa@okayama-u.ac.jp; Fukudome, Yohei; Miyazaki, Shingo; Saari, Mohd Mawardi; Sakai, Kenji; Tsukada, Keiji

2013-11-15

Highlights: •The magnetic evaluation system of a solar panel using HTS-SQUID has been developed. •The electric circuits made by the discrete devices on the circuit board were visualized. •The electric properties of the commercial solar panels were demonstrated. -- Abstract: The magnetic evaluation system of a solar panel using HTS-SQUID has been proposed and developed. A normal pick-up coil was applied to detect the tangential magnetic field to the panel surface. Since the detected field could be related to the currents of the solar panels, the electric properties of the solar panels could be evaluated. In this work, the evaluation of the electric properties of the commercial solar panels as well as the electric circuits made by the discrete devices on the circuit board was visualized.

Magnetic evaluation of a solar panel using HTS-SQUID

International Nuclear Information System (INIS)

Kiwa, Toshihiko; Fukudome, Yohei; Miyazaki, Shingo; Saari, Mohd Mawardi; Sakai, Kenji; Tsukada, Keiji

2013-01-01

Highlights: •The magnetic evaluation system of a solar panel using HTS-SQUID has been developed. •The electric circuits made by the discrete devices on the circuit board were visualized. •The electric properties of the commercial solar panels were demonstrated. -- Abstract: The magnetic evaluation system of a solar panel using HTS-SQUID has been proposed and developed. A normal pick-up coil was applied to detect the tangential magnetic field to the panel surface. Since the detected field could be related to the currents of the solar panels, the electric properties of the solar panels could be evaluated. In this work, the evaluation of the electric properties of the commercial solar panels as well as the electric circuits made by the discrete devices on the circuit board was visualized

75 FR 18484 - Emerging Technology and Research Advisory Committee; Notice of Open Meeting

Science.gov (United States)

2010-04-12

... Emerging Technologies Analysis. 2. ETRAC Panel on Emerging Technologies. 3. History of the Laser. 4... DEPARTMENT OF COMMERCE Bureau of Industry and Security Emerging Technology and Research Advisory Committee; Notice of Open Meeting The Emerging Technology and Research Advisory Committee (ETRAC) [[Page...

Photonically wired spacecraft panels: an economic analysis and demonstrator for telecommunication satellites

Science.gov (United States)

Putzer, Philipp; Hurni, Andreas; Ziegler, Bent; Panopoulou, Aikaterini; Lemke, Norbert; Costa, Ivo; Pereira, Celeste

2017-09-01

In this paper we present the design of smart satellite panels with integrated optical fibers for sensing and data communication. The project starts with a detailed analysis of the system needs and ends with a demonstrator breadboard showing the full performance during and after environmental tests such as vibrations and temperature. Future science missions will need higher bandwidth in the Gbit/s range for intra-satellite communications, so the step from electrical transmission media towards fiber-optical media is the logical next step to cope with future requirements. In addition, the fibers can be used to monitor temperatures directly underneath satellite payloads which will reduce the integration effort in a later phase. For temperature monitoring so called fiber Bragg gratings (FBGs) are written in special radiation tolerant fibers, which reflection wavelength allows a direct link to temperature at the grating position. A read-out system for FBGs to use within satellite applications is currently under development at OHB. For this study, first the environmental requirements for the panels are derived and in a second stage the functional requirements are defined. To define the functional requirements a telecommunication satellite platform, in the case here the Small-GEO series from OHB, has been taken as baseline. Based on the configuration of temperature sensors, communication lines and electrical signaling a possible replacement by fiber-optical technology was defined and traded w.r.t. its economic benefit. It has been pointed out that the replacement of temperature sensors will reduce harness mass, but the great benefit is seen here in the reduction of assembly effort. Once the satellite panel is manufactured, the temperature sensors are already implemented at certain positions. Another point for mass savings which has pointed out is the replacement of the high-voltage or high- current high power commands (HPC) by fiber optics. Replacing some of the several

Fabrication and testing of fire resistant graphite composite panels

Science.gov (United States)

Roper, W. D.

1986-01-01

Eight different graphite composite panels were fabricated using four different resin matrices. The resin matrices included Hercules 71775, a blend of vinylpolystyrpyridine and bismaleimide, H795, a bismaleimide, Cycom 6162, a phenolic, and PSP 6022m, a polystyrylpyridine. Graphite panels were fabricated using fabric or unidirectional tape. Described are the processes for preparing these panels and some of their mechanical, thermal and flammability properties. Panel properties are compared with state-of-the-art epoxy fiberglass composite panels.

Panel Data Evidence on the Demand for Money

OpenAIRE

Serletis, Apostolos; Vaccaro, Jason

2006-01-01

This paper examines the demand for money using panel data for 48 countries over the 1980-95 time period. In our examination of the conventional money demand function, we begin by empirically exploiting traditional panel methodology and fi nd support for heterogeneity among the countries. However, specifi cation and diagnostic tests also indicate serial correlation in all of the estimated models. Recent state-of-the art advances in panel unit root and panel cointegration methodology allow us t...

Sustainable Absorption Panels from Agricultural Wastes

Directory of Open Access Journals (Sweden)

Ismail F.Z.

2014-01-01

Full Text Available Noise has become a serious environmental problem and there are demands for alternative sustainable materials which capable to reduce the noise level at various frequency ranges. Therefore, the aim of this research is to study the potential of turning the agricultural waste and waste paper into a sound absorption panel. For the purpose of this study, combination of two materials was under studied; coconut coir fibre from agriculture waste and shredded waste paper from the office. There were two main objective of the research; first is to develop absorption panels from coconut coir powder that available locally with a combination of shredded paper at different percentage of mixture. Second objective is to identify the absorption rate of the panels. The study encompasses the fabrication of the particle board using the coconut husk powder mix with shredded waste paper and using the gypsum powder as the binder for the two materials. Four acoustic panels of size 0.5m x 0.5m and 0.012 m thick were fabricated with different mix ratio; 25% of coconut coir powder mixed with 75% of shredded waste papers for sample 1, 50% both of the material for sample 2, 75% of coconut coir powder mixed with 25% of shredded waste paper for sample 3, and lastly 100% of coconut coir powder for sample 4. The absorption coefficient of the panels was tested in a reverberation chamber and in accordance with ISO 354:1985 standards. Based on the results, sample 1 gave the highest absorption coefficient compared to sample 2, 3 and 4. It can be concluded that the acoustic panel made from a mixture of 25% coconut coir powder with 75% shredded waste paper provided higher absorption coefficient compared to the performance of the other samples. This might be caused by the size of the coir powder which is very small, creating less void space in between the panel and thus causing it to absorb less sound. Since sound absorption is very much affected by the availability of void space of

Low frequency noise reduction using stiff light composite panels

Institute of Scientific and Technical Information of China (English)

DENG Yongchang; LIN Weizheng

2003-01-01

The experiment presented in this paper is to investigate and analyze the noise reduction at low frequency using stiff light composite panels. Since these composite panels are made of lightweight and stiff materials, this actuation strategy will enable the creation of composite panels for duct noise control without using traditional heavy structural mass. The results suggest that the mass-spring resonance absorption in the case of a comparatively stiff thick panel with a thin flexible plate is more efficient with minimum weight, when subjected to low-frequency (<500 Hz). The efficiency of the panel absorber depends on the mass of the thin flexible plate and the stiffness of the panel.

45 CFR 1801.22 - Interview of Finalists with panel.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Interview of Finalists with panel. 1801.22 Section... FOUNDATION HARRY S. TRUMAN SCHOLARSHIP PROGRAM The Competition § 1801.22 Interview of Finalists with panel. The Foundation invites each Finalist to an interview with a regional review panel. Panels evaluate...

Characterization of Air-Based Photovoltaic Thermal Panels with Bifacial Solar Cells

Directory of Open Access Journals (Sweden)

P. Ooshaksaraei

2013-01-01

Full Text Available Photovoltaic (PV panels account for a majority of the cost of photovoltaic thermal (PVT panels. Bifacial silicon solar panels are attractive for PVT panels because of their potential to enhance electrical power generation from the same silicon wafer compared with conventional monofacial solar panels. This paper examines the performance of air-based bifacial PVT panels with regard to the first and second laws of thermodynamics. Four air-based bifacial PVT panels were designed. The maximum efficiencies of 45% to 63% were observed for the double-path-parallel bifacial PVT panel based on the first law of thermodynamics. Single-path bifacial PVT panel represents the highest exergy efficiency (10%. Double-path-parallel bifacial PVT panel is the second preferred design as it generates up to 20% additional total energy compared with the single-path panel. However, the daily average exergy efficiency of a double-path-parallel panel is 0.35% lower than that of a single-path panel.

75 FR 17701 - High Energy Physics Advisory Panel

Science.gov (United States)

2010-04-07

... DEPARTMENT OF ENERGY High Energy Physics Advisory Panel AGENCY: Department of Energy, Office of... Physics Advisory Panel (HEPAP). Federal Advisory Committee Act (Pub. L. 92-463, 86 Stat. 770) requires... Energy Physics Advisory Panel; U.S. Department of Energy; SC-25/ Germantown Building, 1000 Independence...

Performance Evaluation of PV Panel Under Dusty Condition

Directory of Open Access Journals (Sweden)

Abhishek Kumar Tripathi

2017-11-01

Full Text Available The performance of PV panel depends on the incoming sunlight on its surface. The accumulated airborne dust particles on panel surface creates a barrier in the path of sunlight and panel surface, which significantly reduces the amount of solar radiation falling on the panel surface. The present study shows a significant reduction in short circuit current and power output of PV panel due to dust deposition on its surface, whereas the reduction in open circuit voltage is not much prominent. This study has been carried in the field as well as in the laboratory. The reduction in maximum power output of PV panel for both the studies ensures a linear relation with the dust deposition on its surface. In the field study, the reduction in the power output due to 12.86gm of dust deposition on the panel surface was 43.18%, whereas in the laboratory study it was 44.75% due to 11gm of dust deposition Article History: Received July 10th 2017; Received in revised form Sept 15th 2017x; Accepted 1st Oct 2017; Available online How to Cite This Article: Tripathi, A.K., Aruna, M. and Murthy, Ch.,S.N. (2017. Performance Evaluation of PV Panel Under Dusty Condition. International Journal of Renewable Energy Develeopment, 6(3, 225-233. https://doi.org/10.14710/ijred.6.3.225-233

Effects of vitamin E and its derivativeson diabetic nephropathy in Ratsand identification of diacylglycerol kinase subtype involved in the improvement of diabetic nephropathy

Directory of Open Access Journals (Sweden)

Tomoko Kakehi

2017-10-01

Full Text Available Background: Diabetes is a significant social issue. Controlling diabetic complications such as nephropathy is very important for QOL of diabetic patients. One of the mechanisms which causes diabetic complications is the abnormal activation of protein kinase C (PKC by increased diacylglycerol (DG from hyperglycemia. Diacylglycerol kinase (DGK can attenuate PKC activity by converting DG to phosphatidic acid. Thus far, d-a-tocopherol (VtE treatment has been shown to prevent early changes of diabetic renal dysfunctions by activating DGK. However, it is still unknown whether VtE derivatives improve diabetic nephropathy similarly to VtE, and which DGK subtype is activated by VtE and/or the derivatives. Objective: The purpose of the study was to investigate effects of VtE and its derivatives on diabetic nephropathy in rats, in addition to identifying the DGK subtype involved in the improvement of nephropathy in vivo. Methods: To induce diabetes in rats, six weeks old male Sprague-Dawley rats were intraperitonealy administrated 65 mg/kg streptozocin (STZ in 20 mM citrate buffer. For two or eight weeks, 40 mg/kg VtE, 44 mg/kg acetate VtE (aVtE or 49.3 mg/kg succinate VtE (sVtE was intraperitonealy administrated every other day after STZ administration. The blood glucose level, body weight, and kidney weight, in addition to urinary volume, albumin, and BUN were measured every week after STZ administration. Additionally, in order to identify the DGK subtype activated by VtE and aVtE, the DGK subtype expressed in the rat glomerulus was checked by RT-PCR and western blotting, and the activity in the glomerulus from the rats before and after the VtE and aVtE treatments were measured in the presence or absence of EGTA. Results: Averages of kidney weight and BUN of rats treated with VtE, aVtE and sVtE for 8 weeks were reduced, compared to the control. However, the intraperitoneal administration of sVtE was toxic. Additionally, the amount of urine volume and

Analysis of Panel Data

Science.gov (United States)

Hsiao, Cheng

2003-02-01

Panel data models have become increasingly popular among applied researchers due to their heightened capacity for capturing the complexity of human behavior, as compared to cross-sectional or time series data models. This second edition represents a substantial revision of the highly successful first edition (1986). Recent advances in panel data research are presented in an accessible manner and are carefully integrated with the older material. The thorough discussion of theory and the judicious use of empirical examples make this book useful to graduate students and advanced researchers in economics, business, sociology and political science.

Origami-Inspired Folding of Thick, Rigid Panels

Science.gov (United States)

Trease, Brian P.; Thomson, Mark W.; Sigel, Deborah A.; Walkemeyer, Phillip E.; Zirbel, Shannon; Howell, Larry; Lang, Robert

2014-01-01

To achieve power of 250 kW or greater, a large compression ratio of stowed-to-deployed area is needed. Origami folding patterns were used to inspire the folding of a solar array to achieve synchronous deployment; however, origami models are generally created for near-zero-thickness material. Panel thickness is one of the main challenges of origami-inspired design. Three origami-inspired folding techniques (flasher, square twist, and map fold) were created with rigid panels and hinges. Hinge components are added to the model to enable folding of thick, rigid materials. Origami models are created assuming zero (or near zero) thickness. When a material with finite thickness is used, the panels are required to bend around an increasingly thick fold as they move away from the center of the model. The two approaches for dealing with material thickness are to use membrane hinges to connect the panels, or to add panel hinges, or hinges of the same thickness, at an appropriate width to enable folding.

RETHINKING STAKEHOLDER ENGAGEMENT AND TECHNOLOGY ACCESS IN HEALTH TECHNOLOGY ASSESSMENT: REACTIONS TO POLICY FORUM DISCUSSIONS.

Science.gov (United States)

Sampietro-Colom, Laura; Thomas, Sarah

2016-01-01

The need to progress and innovate in health technology assessment (HTA) is a must in a continuously changing environment. The HTAi Policy Forum reflected on two specific areas for development where it was thought there was need for careful consideration and deliberation during the main annual meeting in February 2016. The study by Husereau et al. (1) in this journal presents the discussions resulting from this Forum. To further share the deliberations of the Forum and with a view to opening this debate to the wider HTA community, a panel session during the HTAi Annual Meeting in Tokyo was organized. Presentations at the panel included a summary of the HTAi Policy Forum discussions and perspectives from a patient, a representative of healthcare system provider, and a representative from an HTA organization and industry. This letter presents the issues raised in the panel session.

Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom

Science.gov (United States)

Heard, Walter L., Jr.; Collins, Timothy J.; Dyess, James W.; Kenner, Scott; Bush, Harold G.

1993-01-01

A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.

Panel-basierte Mixed-Methods-Studien

OpenAIRE

Legewie, Nicolas; Tucci, Ingrid

2016-01-01

Mixed-Methods-Studien erfreuen sich wachsender Beliebtheit. Immer mehr Studien nutzen dabei auch Panel-basierte Mixed-Methods-Designs, in denen bestehende Längsschnittstudien durch qualitative Befragungsformen ergänzt werden. Innerhalb der reichhaltigen Veröffentlichungen zum Thema Mixed-Methods-Forschung finden sich bisher aber kaum Diskussionen solcher Mixed-Methods-Designs. Im vorliegenden Artikel diskutieren wir Design, Durchführung, sowie Potenzialeund Herausforderungen von Panel-basiert...

Critical analysis of emerging forest biorefinery (FBR) technologies for ethanol production

International Nuclear Information System (INIS)

Cohen, J.; Janssen, M.; Chambost, V.; Stuart, P.

2010-01-01

This article provided a literature review of emerging technologies for ethanol production in Canada. A multi-criteria decision making (MCDM) panel was used to weigh critical metrics for evaluating the potential of emerging forest biorefinery technologies for bio-ethanol production. The 3-step methodology identified key factors for evaluating technology pathways. Key factors were applied to a group of selected technologies in order to collect data. All previous criteria were weighted through the MCDM panel in order to rank the technologies, which included biochemical pathway and thermochemical pathway production processes. Criteria included return on investment; feedstock flexibility; technology risk; energy and integration; products and revenue diversification; potential for additional products; and potential environmental impact. The study showed that techno-economic criteria are the most important barriers to the implementation of ethanol biorefineries. While thermochemical processes are economically feasible and provide greater flexibility, biochemical refining processes may provide for the development of other value-added products. 21 refs., 3 tabs., 7 figs.

Critical analysis of emerging forest biorefinery (FBR) technologies for ethanol production

Energy Technology Data Exchange (ETDEWEB)

Cohen, J.; Janssen, M.; Chambost, V.; Stuart, P. [Ecole Polytechnique, Montreal, PQ (Canada). Dept. de Genie Chimique. Design Engineering Chair in Process Integration

2010-05-15

This article provided a literature review of emerging technologies for ethanol production in Canada. A multi-criteria decision making (MCDM) panel was used to weigh critical metrics for evaluating the potential of emerging forest biorefinery technologies for bio-ethanol production. The 3-step methodology identified key factors for evaluating technology pathways. Key factors were applied to a group of selected technologies in order to collect data. All previous criteria were weighted through the MCDM panel in order to rank the technologies, which included biochemical pathway and thermochemical pathway production processes. Criteria included return on investment; feedstock flexibility; technology risk; energy and integration; products and revenue diversification; potential for additional products; and potential environmental impact. The study showed that techno-economic criteria are the most important barriers to the implementation of ethanol biorefineries. While thermochemical processes are economically feasible and provide greater flexibility, biochemical refining processes may provide for the development of other value-added products. 21 refs., 3 tabs., 7 figs.

Japan's technology and manufacturing infrastructure

Science.gov (United States)

Boulton, William R.; Meieran, Eugene S.; Tummala, Rao R.

1995-02-01

The JTEC panel found that, after four decades of development in electronics and manufacturing technologies, Japanese electronics companies are leaders in the development, support, and management of complex, low-cost packaging and assembly technologies used in the production of a broad range of consumer electronics products. The electronics industry's suppliers provide basic materials and equipment required for electronic packaging applications. Panelists concluded that some Japanese firms could be leading U.S. competitors by as much as a decade in these areas. Japan's technology and manufacturing infrastructure is an integral part of its microelectronics industry's success.

75 FR 73166 - Art Advisory Panel-Closed Meeting

Science.gov (United States)

2010-11-29

... DEPARTMENT OF THE TREASURY Internal Revenue Service Art Advisory Panel--Closed Meeting AGENCY: Internal Revenue Service, Treasury. ACTION: Notice of Closed Meeting of Art Advisory Panel for Decorative Art. SUMMARY: A closed meeting of the Art Advisory Panel will be held in Washington, DC. DATES: The...

50 CFR 600.760 - Fishery Negotiation Panel lifetime.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Fishery Negotiation Panel lifetime. 600... ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Fishery Negotiation Panels § 600.760 Fishery Negotiation Panel lifetime. (a) An FNP shall terminate upon either: (1) Submission of...

49 CFR 845.22 - Technical panel.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Technical panel. 845.22 Section 845.22... Technical panel. The Director, Bureau of Accident Investigation, or the Director, Bureau of Field Operations, shall designate members of the Board's technical staff to participate in the hearing and initially...

Robust block bootstrap panel predictability tests

NARCIS (Netherlands)

Westerlund, J.; Smeekes, S.

2013-01-01

Most panel data studies of the predictability of returns presume that the cross-sectional units are independent, an assumption that is not realistic. As a response to this, the current paper develops block bootstrap-based panel predictability tests that are valid under very general conditions. Some

Mode system effects in an online panel study : Comparing a probability-based online panel with two face-to-face reference surveys

NARCIS (Netherlands)

Struminskaya, Bella; de Leeuw, E.D.; Kaczmirek, Lars

2015-01-01

One of the methods for evaluating online panels in terms of data quality is comparing the estimates that the panels provide with benchmark sources. For probability-based online panels, high-quality surveys or government statistics can be used as references. If differences among the benchmark and the

Progress toward clinical implementation of the first flat-panel amorphous silicon imager

International Nuclear Information System (INIS)

Antonuk, Larry E.; El-Mohri, Youcef; Weidong, Huang; Sandler, Howard; Siewerdsen, Jeffrey H.; Yorkston, John

1995-01-01

Purpose: Approximately 7 years after the development of the general concept, megavoltage imagers based on thin-film, flat-panel electronics will likely enter routine clinical use within the next few years. In this paper, current capabilities and anticipated development of this imaging technology as pertains to clinical use will be presented. The results of the first use of this technology with an early prototype imager in a clinical setting are reported. The development of a more advanced clinical prototype imager designed for routine clinical use is described and the clinically-relevant capabilities, advantages, and limitations of this device are described. Materials and Methods: Flat-panel amorphous silicon imagers consist of an imaging array, an x-ray converter, external data acquisition electronics, along with appropriate software and a host workstation. The array consists of a two-dimensional grid of imaging pixels with each pixel consisting of a transistor coupled to a photodiode. An initial study of patient imaging has been performed with an early prototype imager which incorporates a 512x560 array with 450 μm pixels giving an imaging surface of 23x25 cm 2 . Portal images acquired with this prototype imager and with film under similar geometric and irradiation conditions were acquired and compared. In addition, a clinical prototype imager based upon a 26x26 cm 2 array with 508 μm pixels (512x512 pixels) is under development. This prototype incorporates advanced analog and digital external electronics which will improve imaging performance thereby increasing clinical utility of the device. The imagers are interfaced to the operation of a treatment machine so as to allow both radiographic and fluoroscopic operation. Results: The image quality is limited by the presence of pixel and line defects in the array and by the presence of correlated and uncorrelated noise sources in the acquisition system. Nevertheless, the contrast and spatial resolution offered by

Sound transmission through triple-panel structures lined with poroelastic materials

Science.gov (United States)

Liu, Yu

2015-03-01

In this paper, previous theories on the prediction of sound transmission loss for a double-panel structure lined with poroelastic materials are extended to address the problem of a triple-panel structure. Six typical configurations are considered for a triple-panel structure based on the method of coupling the porous layers to the facing panels which determines critically the sound insulation performance of the system. The transfer matrix method is employed to solve the system by applying appropriate types of boundary conditions for these configurations. The transmission loss of the triple-panel structures in a diffuse sound field is calculated as a function of frequency and compared with that of corresponding double-panel structures. Generally, the triple-panel structure with poroelastic linings has superior acoustic performance to the double-panel counterpart, remarkably in the mid-high frequency range and possibly at low frequencies, by selecting appropriate configurations in which those with two air gaps in the structure exhibit the best overall performance over the entire frequency range. The poroelastic lining significantly lowers the cut-on frequency above which the triple-panel structure exhibits noticeably higher transmission loss. Compared with a double-panel structure, the wider range of system parameters for a triple-panel structure due to the additional partition provides more design space for tuning the sound insulation performance. Despite the increased structural complexity, the triple-panel structure lined with poroelastic materials has the obvious advantages in sound transmission loss while without the penalties in weight and volume, and is hence a promising replacement for the widely used double-panel sandwich structure.

Touch panel system for control applications

International Nuclear Information System (INIS)

Crook, K.; Johnson, R.

1976-12-01

The use of finger-sensitive touch panels in association with computer-generated displays for control and monitoring of the Stanford linear accelerator is discussed. This control concept has proven to be very effective. The hardware and software aspects of the Touch Panel portion of the control system are described

Design for whipping pipe impact on reinforced concrete panels

International Nuclear Information System (INIS)

Chen, C.C.; Gurbuz, O.

1984-01-01

This paper describes determination of local and overall effects on reinforced concrete panels due to whipping pipe impact in postulated pipe break events. Local damage includes the prediction of minimum concrete panel thickness required to prevent spalling from the back face of the target reinforced concrete panels. Evaluation of overall effect deals with the ductility ratio calculation for the target reinforced concrete panels. Design curves for determining the minimum panel thickness and the minimum reinforcement of reinforced concrete panels are presented in this paper for some cases commonly encountered in nuclear applications. The methodology and the results provided can be used to determine if an existing reinforced concrete wall is capable of resisting the whipping pipe impact, and consequently, if pipe whip restraints can be eliminated

Linear Strength Vortex Panel Method for NACA 4412 Airfoil

Science.gov (United States)

Liu, Han

2018-03-01

The objective of this article is to formulate numerical models for two-dimensional potential flow over the NACA 4412 Airfoil using linear vortex panel methods. By satisfying the no penetration boundary condition and Kutta condition, the circulation density on each boundary points (end point of every panel) are obtained and according to which, surface pressure distribution and lift coefficients of the airfoil are predicted and validated by Xfoil, an interactive program for the design and analysis of airfoil. The sensitivity of results to the number of panels is also investigated in the end, which shows that the results are sensitive to the number of panels when panel number ranges from 10 to 160. With the increasing panel number (N>160), the results become relatively insensitive to it.

Solarbus Solar Array Innovative Light Weight Mechanical Architecture with Thin Lateral Panels Deployed with Shape Memory Alloy Regulator

Science.gov (United States)

D'Abrigeon, Laurent; Carpine, Anne; Laduree, Gregory

2005-05-01

The standard ALCATEL SOLAR ARRAY PLANAR CONCEPT on the TELECOM market today on flight is named SOLARBUS.This concept is:• 3 to 10 identical panels covered with Si Hi-η celltechnology.• A central mast constitute by 3 to 4 panels and 1yoke linked together by hinges and synchronizedby cables.• From 2 to 6 lateral panelsThis concept is able to fit with the customer requirements in order to have a competitive "global offer at system level" (mass to power ratio 48-50 W/Kg)But, for the near future, in line with the market trend, and based on the previous experience, an improvement of the SOLARBUS Solar Array concept in term of W/kg/€ is essential in order to maintain the competitiveness of the global ALCATEL offer at system level.In order to increase the W/Kg performance Alcatel has developed a new architecture named Lightweight Panel Structure (LPS). The objectives of this new structure are :• To decrease the kg/m2 ratio • To be compatible of all promising cells technology including Si Hi-n, GaAs, GaAs+ small reflectors. This new architecture is based on the fact that during the 3 major life phases of a Solar Array (Launch/Deployment/Deployed orbital life), the structural needs are more important for the central panels than for the lateral panels.So two different panels have been designed :• Central panels (named LPS1)• Lateral panels (named LPS2)The stowing configuration as been adapted : 2 thin lateral panels LPS2 between 2 structural central panels LPS1, and local bumpers to transfer the loads from LPS2 to LPS1.Also one of the more stringent loads applied to the panels are corresponding to deployment loads. In order to limit the mass of reinforcement of the panels, a deployment speed regulator shall be used. In the frame of the new generation of solar arrays, Alcatel has developed a new actuator based on shape memory alloy torsional rod. This light weight component is directly connected to heaters lines and is able to provide great actuation torque

Panel Discussion

Science.gov (United States)

Langer, James

1997-03-01

Panelists: Arthur Bienenstock, Stanford University Cherry Ann Murray, Lucent Technologies Venkatesh Narayanamurti, University of California-Santa Barbara Paul Peercy, SEMI-SEMATECH Robert Richardson, Cornell University James Roberto, Oak Ridge National Laboratory The Board on Physics and Astronomy is undertaking a series of reassessments of all branches of physics as the foundation of a new physics survey. As part of this project, a Committee on Condensed Matter and Materials Physics has been established under the leadership of Venkatesh Narayanamurti of the University of California-Santa Barbara. The committee has been working since June on a study that will include an illustrative recounting of major recent achievements; identification of new opportunities and challenges facing the field; and articulation-for leaders in government, industry, universities, and the public at large-of the important roles played by the field in modern society. An especially urgent issue is how to maintain the intellectual vitality of condensed matter and materials physics, and its contributions to the well-being of the United States, in an era of limited resources. The forum will feature a panel of materials researchers who are members of the Committee on Condensed Matter and Materials Physics. They will give a brief report on the status of the study and engage in a dialogue with the audience about issues facing the condensed matter and materials physics community. Broad community input is vital to the success of the study. Please come and make your voice heard!

Ballistic study of Tensylon®–based panels

Directory of Open Access Journals (Sweden)

L-C. Alil

2018-06-01

Full Text Available Ballistic protection is a matter of interest requested by civilian as well as military needs. The last decade has witnessed an increase in the use of light weight and efficient armour systems. These panels may be used for body protection as well as light vehicle protection against small calibres or to enhance the protection level of heavier vehicles with decreasing or maintaining their weight penalty. Ultra high molecular weight polyethylene is a material of interest for light weight armour applications. The authors designed panels made of hot–pressed Tensylon® in different configurations with thin steel sheets as a backing and shield protection. Comparison of their ballistic performance to the theory predictions reveals the improved ballistic response of the panels. In addition, a non–pressed Tensylon® panel has been tested in order to facilitate the observations of the failure mechanisms inside the panels. Even if not suitable for practical use, such non–pressed panels clearly reveal the dynamic processes at micro–scale that occur during the impact. The failure mechanisms of the material under bullet penetration are discussed based on photography, optical microscopy and scanning electron microscopy. The supposed effects of the panel pressing are discussed based on the observed difference between pressed and non–pressed structures ballistic response.

High Efficiency, High Density Terrestrial Panel. [for solar cell modules

Science.gov (United States)

Wohlgemuth, J.; Wihl, M.; Rosenfield, T.

1979-01-01

Terrestrial panels were fabricated using rectangular cells. Packing densities in excess of 90% with panel conversion efficiencies greater than 13% were obtained. Higher density panels can be produced on a cost competitive basis with the standard salami panels.

Predicting panel scores by linguistic analysis

Energy Technology Data Exchange (ETDEWEB)

Van den Besselaar, P.; Stout, L.; Gou, X

2016-07-01

In this paper we explore the use of text analysis for deriving quality indicators of project proposals. We do full text analysis of 3030 review reports. After term extraction, we aggregate the term occurrences to linguistic categories. Using thse linguistic categories as independent variables, we study how well these predict the grading by the review panels. Together, the different linguistic categories explain about 50% of the variance in the grading of the applications. The relative importance of the different linguistic categories inform us about the way the panels work. This can be used to develop altmetrics for the quality of the peer and panel review processes. (Author)

Solar Panel based Milk Pasteurization

DEFF Research Database (Denmark)

Nielsen, Kirsten Mølgaard; Pedersen, Tom Søndergaard

This paper treats the subject of analysis, design and development of the control system for a solar panel based milk pasteurization system to be used in small villages in Tanzania. The analysis deals with the demands for an acceptable pasteurization, the varying energy supply and the low cost, low...... complexity, simple user interface and high reliability demands. Based on these demands a concept for the pasteurization system is established and a control system is developed. A solar panel has been constructed and the energy absorption has been tested in Tanzania. Based on the test, the pasteurization...... system is dimensioned. A functional prototype of the pasteurization facility with a capacity of 200 l milk/hour has been developed and tested. The system is prepared for solar panels as the main energy source and is ready for a test in Tanzania....

Solar Panel based Milk Pasteurization

DEFF Research Database (Denmark)

Nielsen, Kirsten Mølgaard; Pedersen, Tom Søndergaard

2002-01-01

This paper treats the subject of analysis, design and development of the control system for a solar panel based milk pasteurization system to be used in small villages in Tanzania. The analysis deals with the demands for an acceptable pasteurization, the varying energy supply and the low cost, low...... complexity, simple user interface and high reliability demands. Based on these demands a concept for the pasteurization system is established and a control system is developed. A solar panel has been constructed and the energy absorption has been tested in Tanzania. Based on the test, the pasteurization...... system is dimensioned. A functional prototype of the pasteurization facility with a capacity of 200 l milk/hour has been developed and tested. The system is prepared for solar panels as the main energy source and is ready for a test in Tanzania....

Building America Case Study: Trade-Friendly Retrofit Insulated Panels for Existing Buildings, Albany, New York

Energy Technology Data Exchange (ETDEWEB)

2016-03-01

This project evaluated the effectiveness and affordability of integrating retrofit insulated panels into a re-siding project. The Partnership for Home Innovation (PHI) teamed with New York State Energy Research and Development Authority (NYSERDA), the Albany Housing Authority (AHA), and the New York State Weatherization Assistance Program (WAP) administered by Albany Community Action Partnership to demonstrate an energy retrofit and siding upgrade on a two-story, seven unit, multifamily building in Albany New York (CZ 5). The project focused on accomplishing three goals - doubling the existing wall thermal resistance (from approximately R-13 to a weighted average of R-27), reduction of building air leakage, and completion of the retrofit within a budget where the additional cost for upgrading wall's thermal resistance is equal to the cost of the standard re-siding effort (i.e., the total cost of the energy efficient re-siding scope of work is not more than double the cost of the standard re-siding effort). Lessons learned from the project strongly indicate that the retrofit panel technology can be installed using common installation practices and with minimal training. Other lessons learned include limitation on the use of standard air sealing materials during cold weather installations and the need to develop better installation guidance for trades working with the level of tolerances that may be present in the existing structure. This technology demonstration showed that exterior retrofit panels provide a viable and reasonable option for the siding trades to increase market opportunities and achieve synergistic benefits for aesthetic upgrades to a building's exterior.

Second messenger production in avian medullary nephron segments in response to peptide hormones.

Science.gov (United States)

Goldstein, D L; Reddy, V; Plaga, K

1999-03-01

We examined the sites of peptide hormone activation within medullary nephron segments of the house sparrow (Passer domesticus) kidney by measuring rates of hormone-induced generation of cyclic nucleotide second messenger. Thin descending limbs, thick ascending limbs, and collecting ducts had baseline activity of adenylyl cyclase that resulted in cAMP accumulation of 207 +/- 56, 147 +/- 31, and 151 +/- 41 fmol. mm-1. 30 min-1, respectively. In all segments, this activity increased 10- to 20-fold in response to forskolin. Activity of adenylyl cyclase in the thin descending limb was stimulated approximately twofold by parathyroid hormone (PTH) but not by any of the other hormones tested [arginine vasotocin (AVT), glucagon, atrial natriuretic peptide (ANP), or isoproterenol, each at 10(-6) M]. Thick ascending limb was stimulated two- to threefold by both AVT and PTH; however, glucagon and isoproterenol had no effect, and ANP stimulated neither cAMP nor cGMP accumulation. Adenylyl cyclase activity in the collecting duct was stimulated fourfold by AVT but not by the other hormones; likewise, ANP did not stimulate cGMP accumulation in this segment. These data support a tubular action of AVT and PTH in the avian renal medulla.

Region specific changes in nonapeptide levels during client fish interactions with allopatric and sympatric cleaner fish.

Science.gov (United States)

Soares, Marta C; Cardoso, Sónia C; Mazzei, Renata; André, Gonçalo I; Morais, Marta; Gozdowska, Magdalena; Kalamarz-Kubiak, Hanna; Kulczykowska, Ewa

2017-01-01

Social relationships are crucially dependent on individual ability to learn and remember ecologically relevant cues. However, the way animals recognize cues before engaging in any social interaction and how their response is regulated by brain neuromodulators remains unclear. We examined the putative involvement of arginine vasotocin (AVT) and isotocin (IT), acting at different brain regions, during fish decision-making in the context of cooperation, by trying to identify how fish distinguish and recognize the value of other social partners or species. We hypothesized that the behavioural responses of cleaner fish clients to different social contexts would be underlain by changes in brain AVT and IT levels. We have found that changes in AVT at the level of forebrain and optic tectum are linked with a response to allopatric cleaners (novel or unfamiliar stimuli) while those at cerebellum are associated with the willingness to be cleaned (in response to sympatric cleaners). On the other hand, higher brain IT levels that were solely found in the diencephalon, also in response to allopatric cleaners. Our results are the first to implicate these nonapeptides, AVT in particular, in the assessment of social cues which enable fish to engage in mutualistic activities.

Information Technology Research & Development Foresight in Iran.

Directory of Open Access Journals (Sweden)

Mansoor Sheydaee

2017-09-01

The results of the Delphi process was reported in national level, including Delphi panel members demography, public questions and specialized questions for each of the technologies. Finally the research provides some recommendations for decision makers.

Handbook of display technology

CERN Document Server

Castellano, Joseph A

1992-01-01

This book presents a comprehensive review of technical and commercial aspects of display technology. It provides design engineers with the information needed to select proper technology for new products. The book focuses on flat, thin displays such as light-emitting diodes, plasma display panels, and liquid crystal displays, but it also includes material on cathode ray tubes. Displays include a large number of products from televisions, auto dashboards, radios, and household appliances, to gasoline pumps, heart monitors, microwave ovens, and more.For more information on display tech

78 FR 30863 - Judges Panel of the Malcolm Baldrige National Quality Award and Board of Overseers of the Malcolm...

Science.gov (United States)

2013-05-23

... Standards and Technology and from the Chair of the Judges Panel of the Malcolm Baldrige National Quality... with balanced representation from U.S. service, manufacturing, nonprofit, education, and health care... issues of manufacturing companies, service companies, small businesses, health care providers, and...

Performance of patch repaired composite panels under fatigue loads

International Nuclear Information System (INIS)

Darwish, Feras H.; Hamoush, S.; Shivakumar, K.

2006-01-01

This paper evaluates the performance of bonded patch-scarf repairs of full scale laminated composite panels under cyclic load conditions. Nondestructive testing to characterize the quality of repairs and destructive testing to evaluate the performance of repaired panels were used in this study. Carbon/Epoxy prepreg material used was used to lay up six-ply (12 in. x 27 in. /305x686mm) (-60/60/0) s quasi-isotropic laminates. 7-ply scarf repair with a gradient of 0.5 inch (12.7mm) per layer was used to perform the repair of a damaged zone. The patch consisted of 7.5 inches (190mm) diameter adhesive film, 1 inch (25.4mm) diameter filler ply at 90fiber orientation, and six plies (2-7 inches (51-178mm) diameter) to match the lay-up of the parent material. The study was extended to include defective repairs. The defect was engineered by inserting a 1 inch (25.4 mm) circular Teflon flaw between the fifth and sixth layers of the patch. A total of 28 panels were prepared and divided into five categories: (1) three pristine panels (undamaged parental materials); (2) three damaged panels (1-inch-centered-hole); (3) two repaired panels with wrong fiber orientation; (4) nine good repaired panels, and (5) eleven defective repair panels (1 inch flaw). A nondestructive evaluation to check the conditions of the repairs was performed on most of the tested panels that include the pulse-echo C-scan and pseudo through transmission air coupled and water coupled C-scan. Based on the results of the experimental evaluation of this study, good repair restored 95% of the tensile strength while defective repair restored 90% of the tensile strength of the pristine panels. Under fatigue loading, panels repaired with a 1 inch delamination flaw within the patch layers showed a major reduction in fatigue life compared to the good repair panels under similar loading conditions. (author)

An imaging-based photometric and colorimetric measurement method for characterizing OLED panels for lighting applications

Science.gov (United States)

Zhu, Yiting; Narendran, Nadarajah; Tan, Jianchuan; Mou, Xi

2014-09-01

The organic light-emitting diode (OLED) has demonstrated its novelty in displays and certain lighting applications. Similar to white light-emitting diode (LED) technology, it also holds the promise of saving energy. Even though the luminous efficacy values of OLED products have been steadily growing, their longevity is still not well understood. Furthermore, currently there is no industry standard for photometric and colorimetric testing, short and long term, of OLEDs. Each OLED manufacturer tests its OLED panels under different electrical and thermal conditions using different measurement methods. In this study, an imaging-based photometric and colorimetric measurement method for OLED panels was investigated. Unlike an LED that can be considered as a point source, the OLED is a large form area source. Therefore, for an area source to satisfy lighting application needs, it is important that it maintains uniform light level and color properties across the emitting surface of the panel over a long period. This study intended to develop a measurement procedure that can be used to test long-term photometric and colorimetric properties of OLED panels. The objective was to better understand how test parameters such as drive current or luminance and temperature affect the degradation rate. In addition, this study investigated whether data interpolation could allow for determination of degradation and lifetime, L70, at application conditions based on the degradation rates measured at different operating conditions.

Hepatitis Panel: MedlinePlus Lab Test Information

Science.gov (United States)

... this page: https://medlineplus.gov/labtests/hepatitispanel.html Hepatitis Panel To use the sharing features on this page, please enable JavaScript. What is a Hepatitis Panel? Hepatitis is a type of liver disease. ...

Increasing the efficiency of solar thermal panels

Science.gov (United States)

Dobrnjac, M.; Latinović, T.; Dobrnjac, S.; Živković, P.

2016-08-01

The popularity of solar heating systems is increasing for several reasons. These systems are reliable, adaptable and pollution-free, because the renewable solar energy is used. There are many variants of solar systems in the market mainly constructed with copper pipes and absorbers with different quality of absorption surface. Taking into account the advantages and disadvantages of existing solutions, in order to increase efficiency and improve the design of solar panel, the innovative solution has been done. This new solar panel presents connection of an attractive design and the use of constructive appropriate materials with special geometric shapes. Hydraulic and thermotechnical tests that have been performed on this panel showed high hydraulic and structural stability. Further development of the solar panel will be done in the future in order to improve some noticed disadvantages.

The Effects of Soldier Gear Encumbrance on Restraints in a Frontal Crash Environment

Science.gov (United States)

2015-08-31

ASME 2015 IDETC/ CIE AVT-7-1 Advances in Military and Commercial Ground Vehicle Design Sebastian Karwaczynski Lead Restraint Development Engineer...release; distribution unlimited 13. SUPPLEMENTARY NOTES ASME 2015 IDETC/ CIE AVT-7-1 Advances in Military and Commercial Ground Vehicle Design 14...has to date not accounted for the Soldier gear burden. •Actual loads imparted onto the occupant in a representative military vehicle crash test

Operational Based Vision Assessment Automated Vision Test Collection User Guide

Science.gov (United States)

2017-05-15

AFRL-SA-WP-SR-2017-0012 Operational Based Vision Assessment Automated Vision Test Collection User Guide Elizabeth Shoda, Alex...June 2015 – May 2017 4. TITLE AND SUBTITLE Operational Based Vision Assessment Automated Vision Test Collection User Guide 5a. CONTRACT NUMBER... automated vision tests , or AVT. Development of the AVT was required to support threshold-level vision testing capability needed to investigate the

The effect of oblique angle of sound incidence, realistic edge conditions, curvature and in-plane panel stresses on the noise reduction characteristics of general aviation type panels

Science.gov (United States)

Grosveld, F.; Lameris, J.; Dunn, D.

1979-01-01

Experiments and a theoretical analysis were conducted to predict the noise reduction of inclined and curved panels. These predictions are compared to the experimental results with reasonable agreement between theory and experiment for panels under an oblique angle of sound incidence. Theoretical as well as experimental results indicate a big increase in noise reduction when a flat test panel is curved. Further curving the panel slightly decreases the noise reduction. Riveted flat panels are shown to give a higher noise reduction in the stiffness-controlled frequency region, while bonded panels are superior in this region when the test panel is curved. Experimentally measured noise reduction characteristics of flat aluminum panels with uniaxial in-plane stresses are presented and discussed. These test results indicate an important improvement in the noise reduction of these panels in the frequency range below the fundamental panel/cavity frequency.

Improving the environmental profile of wood panels via co-production of ethanol and acetic acid.

Science.gov (United States)

Earles, J Mason; Halog, Anthony; Shaler, Stephen

2011-11-15

The oriented strand board (OSB) biorefinery is an emerging technology that could improve the building, transportation, and chemical sectors' environmental profiles. By adding a hot water extraction stage to conventional OSB panel manufacturing, hemicellulose polysaccharides can be extracted from wood strands and converted to renewably sourced ethanol and acetic acid. Replacing fossil-based gasoline and acetic acid has the potential to reduce greenhouse gas (GHG) emissions, among other possible impacts. At the same time, hemicellulose extraction could improve the environmental profile of OSB panels by reducing the level of volatile organic compounds (VOCs) emitted during manufacturing. In this study, the life cycle significance of such GHG, VOC, and other emission reductions was investigated. A process model was developed based on a mix of laboratory and industrial-level mass and energy flow data. Using these data a life cycle assessment (LCA) model was built. Sensitive process parameters were identified and used to develop a target production scenario for the OSB biorefinery. The findings suggest that the OSB biorefinery's deployment could substantially improve human and ecosystem health via reduction of select VOCs compared to conventionally produced OSB, gasoline, and acetic acid. Technological advancements are needed, however, to achieve desirable GHG reductions.

Documentation Panels Enhance Teacher Education Programs

Science.gov (United States)

Warash, Bobbie Gibson

2005-01-01

Documentation of children's projects is advantageous to their learning process and is also a good method for student teachers to observe the process of learning. Documentation panels are a unique way to help student teachers understand how children learn. Completing a panel requires a student teacher to think through a process. Teachers must learn…

Research Needs for Technology Education: An International Perspective

Science.gov (United States)

Ritz, John M.; Martin, Gene

2013-01-01

These authors report the findings of a study that sought to determine the most relevant research issues needed to be studied by the technology education profession. It used an international panel of experts to develop a list of important research issues for the school subject of technology education and for the preparation of teachers to better…

Experimental and numerical results from hybrid retrofitted photovoltaic panels

International Nuclear Information System (INIS)

Rossi, Cecilia; Tagliafico, Luca A.; Scarpa, Federico; Bianco, Vincenzo

2013-01-01

Highlights: • The experimental study focuses on the feasibility of hybrid PV/T panels retrofitting. • The critical role of a thin layer of air between PV panel and back plate is evidenced. • The benefit of the addition of a conductive paste layer is analyzed via FEM simulations. • The use of wood ribs to stick the back plate represents a cheap effective solution. - Abstract: The aim of present study is to investigate different methodologies to achieve a better contact between a photovoltaic panel and a thermal plate, in order to cool the PV panel by means of water in the perspective of coupling it with a heat pump. It is believed that this kind of system allows to obtain a higher energy efficiency. The analysis is developed both experimentally and numerically, testing different kinds of configurations in different operating conditions. Simulations are employed to analyze the effect of the variations of the contact resistance between the panel and the thermal plates, demonstrating that the use of a conductive paste increases the overall performance of the panel. Results show interesting possibilities in terms of retrofitting of existing photovoltaic panels by employing very simple solutions, such as to fix the thermal plate on the rear of the panel by means of wood ribs

TWRS vadose zone contamination issue expert panel report

Energy Technology Data Exchange (ETDEWEB)

Shafer, D.S.

1997-05-01

When members were first canvassed for participation in the Vadose Zone Expert Panel the stated purpose for convening the Panel was to review a controversial draft report, the SX Tank Farm Report. This report was produced by a DOE Grand Junction Project Office (GJPO) contractor, RUST Geotech, now MACTEC-ERS, for the DOE Richland Office (DOERL). Three meetings were planned for June, July and August, 1995 to review the draft report and to complete a Panel report by mid-September. The Expert Panel has found its efforts confounded by various non-technical issues. The Expert Panel has chosen to address some of the non-technical issues in this Preface rather than to dilute the technical discussion that follows in the body of this independent expert panel status report (Panel Report). Rather than performing a straightforward manuscript review, the Panel was asked to resolve conflicting interpretations of gamma-ray logging measurements performed in vadose zone boreholes (drywells) surrounding the high-level radioactive wastes of the SX tank farm. There are numerous and complex technical issues that must be evaluated before the vertical and radial extent of contaminant migration at the SX tank farm can be accurately assessed. When the Panel first met in early June, 1996, it quickly became apparent that the scientific and technical issues were obscured by policy and institutional affairs which have polarized discussion among various segments of the Hanford organization. This situation reflects the kinds of institutional problems described separately in reports by the National Research Council of the National Academy of Sciences (NAS/NRC), The Hanford Tanks Environmental Impacts and Policy Choices and BmTiers to Science: Technical Management of the Department of Energy Environmental Remediation Program. The Vadose Zone Characterization Program, appears to be caught between conflicting pressures and organizational mandates, some imposed from outside DOE-RL and some self

Heat Rejection from a Variable Conductance Heat Pipe Radiator Panel

Science.gov (United States)

Jaworske, D. A.; Gibson, M. A.; Hervol, D. S.

2012-01-01

A titanium-water heat pipe radiator having an innovative proprietary evaporator configuration was evaluated in a large vacuum chamber equipped with liquid nitrogen cooled cold walls. The radiator was manufactured by Advanced Cooling Technologies, Inc. (ACT), Lancaster, PA, and delivered as part of a Small Business Innovative Research effort. The radiator panel consisted of five titanium-water heat pipes operating as thermosyphons, sandwiched between two polymer matrix composite face sheets. The five variable conductance heat pipes were purposely charged with a small amount of non-condensable gas to control heat flow through the condenser. Heat rejection was evaluated over a wide range of inlet water temperature and flow conditions, and heat rejection was calculated in real-time utilizing a data acquisition system programmed with the Stefan-Boltzmann equation. Thermography through an infra-red transparent window identified heat flow across the panel. Under nominal operation, a maximum heat rejection value of over 2200 Watts was identified. The thermal vacuum evaluation of heat rejection provided critical information on understanding the radiator s performance, and in steady state and transient scenarios provided useful information for validating current thermal models in support of the Fission Power Systems Project.

Optimal design of sound absorbing systems with microperforated panels

Science.gov (United States)

Kim, Nicholas Nakjoo

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles. This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound absorbing materials), usually in the form of a thin panel with small holes, and an air backing may be one of the preferred solutions. These panels can be designed in many ways, and usually feature many small (sub-millimeter) holes and typically surface porosities on the order of 1 percent. The detailed acoustical properties of MPPs depend on their hole shape, the hole diameter, the thickness of the panel, the overall porosity of the perforated film, the film's mass per unit area, and the depth of the backing air cavity. Together, these parameters control the absorption peak location and the magnitude of the absorption coefficient (and the magnitude of the transmission loss in barrier applications). By an appropriate choice of these parameters good absorption performance can be achieved in a frequency range one or two octaves wide. That kind of solution may be adequate when it is necessary to control sound only in a specified frequency range (in the speech interference range, for example). However, in order to provide appropriate noise control solutions over a broader range of frequencies, it is necessary to design systems featuring multiple-layers of MPPs, thus creating what amounts to a multi-degree-of-freedom system and so expanding the range over which good absorption can be obtained. In this research

Causal Dynamic Relationships between Political–Economic Factors and Export Performance in the Renewable Energy Technologies Market

Directory of Open Access Journals (Sweden)

Bongsuk Sung

2018-04-01

Full Text Available This study explores how political–economic forces could affect export performance in the renewable energy technologies market. We conduct panel framework analyses to verify the characteristics of panel data for 19 countries before establishing the panel estimator meant to test the effects of political–economic forces on export specialization. We consider the results of the panel framework analyses and develop an empirical model to test casual dynamic relationships between political–economic forces and export performance. The results from the least squares dummy variable-corrected estimation indicate that the major factors promoting the export specialization of renewable energy technologies are, in order of decreasing importance, public pressure, market size, and government demand-pull policy. However, the traditional energy industry has no significant effect on export performance. Finally, this study finds that dynamic effects exist in all estimations.

Assessment of the Greenhouse Gas Emission Reduction Potential of Ultra-Clean Hybrid-Electric Vehicles

OpenAIRE

Burke, A.F.; Miller, M.

1997-01-01

The study focused on the emission reduction and fuel economy benefits of the application of hybrid/electric powertrain technology to tight-duty vehicles (mid-size and compact passenger cars). The approach taken was to calculate the exhaust emissions (gm/mi) energy use (Wh/mi and mpg) for a wide range of vehicle designs (steel and light-weight materials), engines, energy storage devices, control strategies, and driving cycles using two vehicle simulation programs (SIMPLEV and AVTE). The full f...

Technologic Information about Photovoltaic Applied in Urban Residences

OpenAIRE

Stephanie Fabris Russo; Daiane Costa Guimarães; Jonas Pedro Fabris; Maria Emilia Camargo; Suzana Leitão Russo; José Augusto Andrade Filho

2016-01-01

Among renewable energy sources, solar energy is the one that has stood out. Solar radiation can be used as a thermal energy source and can also be converted into electricity by means of effects on certain materials, such as thermoelectric and photovoltaic panels. These panels are often used to generate energy in homes, buildings, arenas, etc., and have low pollution emissions. Thus, a technological prospecting was performed to find patents related to the use of photovoltaic plates in urban re...

Artificial Neural Network based control for PV/T panel to track optimum thermal and electrical power

International Nuclear Information System (INIS)

Ben Ammar, Majed; Chaabene, Maher; Chtourou, Zied

2013-01-01

Highlights: ► We establish a state model of PV/T panel. ► We study the effect of mass flow rate on PV/T efficiency. ► A real time PV/T control algorithm is proposed. ► A model based optimal thermal and electrical power operation point is tracked. - Abstract: As solar energy is intermittent, many algorithms and electronics have been developed to track the maximum power generation from photovoltaic and thermal panels. Following technological advances, these panels are gathered into one unit: PV/T system. PV/T delivers simultaneously two kinds of power: electrical power and thermal power. Nevertheless, no control systems have been developed in order to track maximum power generation from PV/T system. This paper suggests a PV/T control algorithm based on Artificial Neural Network (ANN) to detect the optimal power operating point (OPOP) by considering PV/T model behavior. The OPOP computes the optimum mass flow rate of PV/T for a considered irradiation and ambient temperature. Simulation results demonstrate great concordance between OPOP model based calculation and ANN outputs.

Technical Evaluation Report, Part A - Vortex Flow and High Angle of Attack

Science.gov (United States)

Luckring, James M.

2003-01-01

A symposium entitled Vortex Flow and High Angle of Attack was held in Loen, Norway, from May 7 through May 11, 2001. The Applied Vehicle Technology (AVT) panel, under the auspices of the Research and Technology Organization (RTO), sponsored this symposium. Forty-eight papers, organized into nine sessions, addressed computational and experimental studies of vortex flows pertinent to both aircraft and maritime applications. The studies also ranged from fundamental fluids investigations to flight test results, and significant results were contributed from a broad range of countries. The principal emphasis of this symposium was on "the understanding and prediction of separation-induced vortex flows and their effects on military vehicle performance, stability, control, and structural design loads." It was further observed by the program committee that "separation- induced vortex flows are an important part of the design and off-design performance of conventional fighter aircraft and new conventional or unconventional manned or unmanned advanced vehicle designs (UAVs, manned aircraft, missiles, space planes, ground-based vehicles, and ships)." The nine sessions addressed the following topics: vortical flows on wings and bodies, experimental techniques for vortical flows, numerical simulations of vortical flows, vortex stability and breakdown, vortex flows in maritime applications, vortex interactions and control, vortex dynamics, flight testing, and vehicle design. The purpose of this paper is to provide brief reviews of these papers along with some synthesizing perspectives toward future vortex flow research opportunities. The paper includes the symposium program. (15 refs.)

Family Medicine Panel Size with Care Teams: Impact on Quality.

Science.gov (United States)

Angstman, Kurt B; Horn, Jennifer L; Bernard, Matthew E; Kresin, Molly M; Klavetter, Eric W; Maxson, Julie; Willis, Floyd B; Grover, Michael L; Bryan, Michael J; Thacher, Tom D

2016-01-01

The demand for comprehensive primary health care continues to expand. The development of team-based practice allows for improved capacity within a collective, collaborative environment. Our hypothesis was to determine the relationship between panel size and access, quality, patient satisfaction, and cost in a large family medicine group practice using a team-based care model. Data were retrospectively collected from 36 family physicians and included total panel size of patients, percentage of time spent on patient care, cost of care, access metrics, diabetic quality metrics, patient satisfaction surveys, and patient care complexity scores. We used linear regression analysis to assess the relationship between adjusted physician panel size, panel complexity, and outcomes. The third available appointments (P size. Patient satisfaction, cost, and percentage fill rate were not affected by panel size. A physician-adjusted panel size larger than the current mean (2959 patients) was associated with a greater likelihood of poor-quality rankings (≤25th percentile) compared with those with a less than average panel size (odds ratio [OR], 7.61; 95% confidence interval [CI], 1.13-51.46). Increased panel size was associated with a longer time to the third available appointment (OR, 10.9; 95% CI, 1.36-87.26) compared with physicians with panel sizes smaller than the mean. We demonstrated a negative impact of larger panel size on diabetic quality results and available appointment access. Evaluation of a family medicine practice parameters while controlling for panel size and patient complexity may help determine the optimal panel size for a practice. © Copyright 2016 by the American Board of Family Medicine.

FPGA Implementation of Multilayer Perceptron for Modeling of Photovoltaic panel

International Nuclear Information System (INIS)

Mekki, H.; Belhout, K.; Mellit, A.; Salhi, H.

2008-01-01

The Number of electronic applications using artificial neural network-based solutions has increased considerably in the last few years. However, their applications in photovoltaic systems are very limited. This paper introduces the preliminary result of the modeling and simulation of photovoltaic panel based on neural network and VHDL-language. In fact, an experimental database of meteorological data (irradiation, temperature) and output electrical generation signals of the PV-panel (current and voltage) has been used in this study. The inputs of the ANN-PV-panel are the daily total irradiation and mean average temperature while the outputs are the current and voltage generated from the panel. Firstly, a dataset of 4x364 have been used for training the network. Subsequently, the neural network (MLP) corresponding to PV-panel is simulated using VHDL language based on the saved weights and bias of the network. Simulation results of the trained MLP-PV panel based on Matlab and VHDL are presented. The proposed PV-panel model based ANN and VHDL permit to evaluate the performance PV-panel using only the environmental factors and involves less computational efforts, and it can be used for predicting the output electrical energy from the PV-panel

The Improvement of Thermal Insulating Concrete Panel

Directory of Open Access Journals (Sweden)

Mohammed Ali Nasser Ali

2018-05-01

Full Text Available The Iraqi houses flattening the roof by a concrete panel, and because of the panels on the top directly exposed to the solar radiation become unbearably hot and cold during the summer and winter. The traditional concrete panel components are cement, sand, and aggregate, which have a poor thermal property. The usage of materials with low thermal conductivity with no negative reflects on its mechanical properties gives good improvements to the thermal properties of the concrete panel. The practical part of this work was built on a multi-stage mixing plan. In the first stage the mixing ratio based on the ratios of the sand to cement. The second stage mixing ratios based on replacing the coarse aggregate quantities with the Alabaster aggregates, and the third stage the mixing ratios based on the replacement of wood ash instead of the sand. While the fourth stage mixing ratios based on decreasing the thermal conductivity and increasing mechanical properties by adding a multilayer of a plastic net. The result shows that using a concrete panel with components (cement, sand, coarse aggregate, wood ash, and Alabaster aggregates with a mass ratio of (1:1:2:1:1 and 3-plastic layers, gives the best improvement of the thermal properties. Where, the thermal conductivity is reduced by 42% and the specific heat increased by 41.2% as compared to the traditional concrete panel mixing ratio, with mechanical properties are agreed with the Iraqi standards.

The gain of single-axis tracked panel according to extraterrestrial radiation

International Nuclear Information System (INIS)

Chang, T.P.

2009-01-01

In the present study, the gain in extraterrestrial radiation received by a single-axis tracked panel relative to a fixed panel was systematically analyzed over a specific period of time. The dynamic angle that the tracked panel should rotate by in order to follow the sun was derived through a series of spherical trigonometric procedures. The instantaneous incident angle of sunlight upon the panel was then calculated, assuming that the panel would simultaneously follow the sun's position. Thus, instantaneous increments of solar energy received by the tracked panel relative to the fixed panel are originally presented. The results show that the angle the tracked panel has to rotate by is 0 deg. at solar noon, and increases towards dawn or dusk. The incident angle of sunlight upon the tracked panel is always smaller than that upon the fixed panel, except at solar noon. As for panels installed with a yearly optimal tilt angle in Taipei, the gains are between 36.3% and 62.1% for four particular days of year, between 37.8% and 60.8% for the four seasons and 49.3% over the entire year. The amount of radiation collected by the tracked panel is enhanced as the maximum rotation angle is increased. The irradiation ratio of the tracked panel to the fixed panel is close to 1.5 for latitudes below 65 deg. and gradually increases for latitudes above this. The yearly optimal tilt angle of a south-facing fixed panel is approximately equal to 0.9 multiplied by the latitude (i.e. 0.9 x φ) for latitudes below 65 deg. and is about 56 + 0.4 x (φ - 65) otherwise

Automatic outdoor monitoring system for photovoltaic panels.

Science.gov (United States)

Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

2016-05-01

Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

Automatic outdoor monitoring system for photovoltaic panels

Energy Technology Data Exchange (ETDEWEB)

Stefancich, Marco [Consiglio Nazionale delle Ricerce, Istituto dei Materiali per l’Elettronica ed il Magnetismo (CNR-IMEM), Parco Area delle Scienze 37/A, 43124 Parma, Italy; Simpson, Lin [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401, USA; Chiesa, Matteo [Masdar Institute of Science and Technology, P.O. Box 54224, Masdar City, Abu Dhabi, United Arab Emirates

2016-05-01

Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

Panel Discussion: Creating a Spirit of Inquiry in the Classroom

Science.gov (United States)

Leh, Sandra Kundrik; Melincavage, Sharon M.

2012-01-01

A paucity of published literature exists related to the use of panel discussion as a teaching strategy. This article describes the panel discussion, the underpinnings of constructivism and the use of panel discussion to create a constructivist classroom environment. Details of planning, evaluating, and challenges of a panel discussion are also…

Atomic Safety and Licensing Board Panel annual report

International Nuclear Information System (INIS)

1991-09-01

In Fiscal Year 1990, The Atomic Safety and Licensing Board Panel (Panel) handled 40 proceedings involving the construction, operation, and maintenance of commercial nuclear power reactors or other activities requiring a license from the Nuclear Regulatory Commission. This report summarizes, highlights, and analyzes how the judges and licensing boards of the Panel addressed the wide-ranging issues raised in these proceedings during the year

Technology Solutions for Existing Homes Case Study: Trade-Friendly Retrofit Insulated Panels for Existing Buildings

Energy Technology Data Exchange (ETDEWEB)

None

2016-03-01

For this project with the U.S. Department of Energy Building America team Home Innovation Research Labs, the retrofit insulated panels relied on an enhanced expanded polystyrene (EPS) for thermal resistance of R-4.5/inch, which is an improvement of 10% over conventional (white-colored) EPS. EPS, measured by its life cycle, is an alternative to commonly used extruded polystyrene and spray polyurethane foam. It is a closed-cell product made up of 90% air, and it requires about 85% fewer petroleum products for processing than other rigid foams.

Installation package for concentrating solar collector panels

Science.gov (United States)

1978-01-01

The concentrating solar collector panels comprise a complete package array consisting of collector panels using modified Fresnel prismatic lenses for a 10 to 1 concentrating ratio, supporting framework, fluid manifolding and tracking drive system, and unassembled components for field erection.

Low-cost production of solar-cell panels

Science.gov (United States)

Bickler, D. B.; Gallagher, B. D.; Sanchez, L. E.

1980-01-01

Large-scale production model combines most modern manufacturing techniques to produce silicon-solar-cell panels of low costs by 1982. Model proposes facility capable of operating around the clock with annual production capacity of 20 W of solar cell panels.

Improving Pattern Recognition and Neural Network Algorithms with Applications to Solar Panel Energy Optimization

Science.gov (United States)

Zamora Ramos, Ernesto

Artificial Intelligence is a big part of automation and with today's technological advances, artificial intelligence has taken great strides towards positioning itself as the technology of the future to control, enhance and perfect automation. Computer vision includes pattern recognition and classification and machine learning. Computer vision is at the core of decision making and it is a vast and fruitful branch of artificial intelligence. In this work, we expose novel algorithms and techniques built upon existing technologies to improve pattern recognition and neural network training, initially motivated by a multidisciplinary effort to build a robot that helps maintain and optimize solar panel energy production. Our contributions detail an improved non-linear pre-processing technique to enhance poorly illuminated images based on modifications to the standard histogram equalization for an image. While the original motivation was to improve nocturnal navigation, the results have applications in surveillance, search and rescue, medical imaging enhancing, and many others. We created a vision system for precise camera distance positioning motivated to correctly locate the robot for capture of solar panel images for classification. The classification algorithm marks solar panels as clean or dirty for later processing. Our algorithm extends past image classification and, based on historical and experimental data, it identifies the optimal moment in which to perform maintenance on marked solar panels as to minimize the energy and profit loss. In order to improve upon the classification algorithm, we delved into feedforward neural networks because of their recent advancements, proven universal approximation and classification capabilities, and excellent recognition rates. We explore state-of-the-art neural network training techniques offering pointers and insights, culminating on the implementation of a complete library with support for modern deep learning architectures

Detailed design report for an operational phase panel-closure system

International Nuclear Information System (INIS)

1996-01-01

Under contract to Westinghouse Electric Corporation (Westinghouse), Waste Isolation Division (WID), IT Corporation has prepared a detailed design of a panel-closure system for the Waste Isolation Pilot Plant (WIPP). Preparation of this detailed design of an operational-phase closure system is required to support a Resource Conservation and Recovery Act (RCRA) Part B permit application and a non-migration variance petition. This report describes the detailed design for a panel-closure system specific to the WIPP site. The recommended panel-closure system will adequately isolate the waste-emplacement panels for at least 35 years. This report provides detailed design and material engineering specifications for the construction, emplacement, and interface-grouting associated with a panel-closure system at the WIPP repository, which would ensure that an effective panel-closure system is in place for at least 35 years. The panel-closure system provides assurance that the limit for the migration of volatile organic compounds (VOC) will be met at the point of compliance, the WIPP site boundary. This assurance is obtained through the inherent flexibility of the panel-closure system

Energy-active walls for solar houses made by using energy accumulating panels with ecologically safe panels

International Nuclear Information System (INIS)

Alexandrov, Y.

2006-01-01

The paper presents the opportunities for separate assemblage and dismounting of the structural layers of energy-accumulating panels, meant for construction of energy-active walls, which could find an application in the process of building of so called 'solar houses'. A situation has been considered, for a panel, whose structure layers after the expiration of their operational term could be dismounted separately and could be recycled for secondary use

Night time cooling by ventilation or night sky radiation combined with in-room radiant cooling panels including phase change materials

DEFF Research Database (Denmark)

Bourdakis, Eleftherios; Olesen, Bjarne W.; Grossule, Fabio

Night sky radiative cooling technology using PhotoVoltaic/Thermal panels (PVT) and night time ventilation have been studied both by means of simulations and experiments to evaluate their potential and to validate the created simulation model used to describe it. An experimental setup has been...... depending on the sky clearness. This cooling power was enough to remove the stored heat and regenerate the ceiling panels. The validation simulation model results related to PCM were close to the corresponding results extracted from the experiment, while the results related to the production of cold water...... through the night sky radiative cooling differed significantly. The possibility of night time ventilation was studied through simulations for three different latitudes. It was concluded that for Danish climatic conditions night time ventilation would also be able to regenerate the panels while its...

Behavior of Frame-Stiffened Composite Panels with Damage

Science.gov (United States)

Jegley, Dawn C.

2013-01-01

NASA, the Air Force Research Laboratory and The Boeing Company have worked to develop new low-cost, light-weight composite structures for aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept has been developed which offers advantages over traditional metallic structures. In this concept, a stitched carbon-epoxy material system has been developed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners, thereby reducing part count and labor. Stitching and the use of thin skins with rod-stiffeners to move loading away from the morevulnerable outer surface produces a structurally efficient, damage tolerant design. This study focuses on the behavior of PRSEUS panels loaded in the frame direction and subjected to severe damage in the form of a severed central frame in a three-frame panel. Experimental results for a pristine two-frame panel and analytical predictions for pristine two-frame and three-frame panels as well as damaged three-frame panels are described.

78 FR 57903 - Aerospace Safety Advisory Panel; Charter Renewal

Science.gov (United States)

2013-09-20

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice: 13-116] Aerospace Safety Advisory Panel... and amendment of the charter of the Aerospace Safety Advisory Panel. SUMMARY: Pursuant to sections 14... determined that renewal and amendment of the charter of the Aerospace Safety Advisory Panel is in the public...

76 FR 65750 - Aerospace Safety Advisory Panel; Charter Renewal

Science.gov (United States)

2011-10-24

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (11-105)] Aerospace Safety Advisory Panel... and amendment of the charter of the NASA Aerospace Safety Advisory Panel. SUMMARY: Pursuant to... determined that a renewal and amendment of the charter of the NASA Aerospace Safety Advisory Panel is in the...

78 FR 74174 - Humanities Panel Advisory Committee

Science.gov (United States)

2013-12-10

... NATIONAL FOUNDATION ON THE ARTS AND THE HUMANITIES Humanities Panel Advisory Committee AGENCY: National Endowment for the Humanities. ACTION: Notice of Charter Renewal for Humanities Panel Advisory... its implementing regulations, 41 CFR 102-3.65, the National Endowment for the Humanities (NEH) gives...

Research challenges for energy data management (panel)

DEFF Research Database (Denmark)

Pedersen, Torben Bach; Lehner, Wolfgang

2013-01-01

This panel paper aims at initiating discussion at the Second International Workshop on Energy Data Management (EnDM 2013) about the important research challenges within Energy Data Management. The authors are the panel organizers, extra panelists will be recruited before the workshop...

Thermal Change for Photovoltaic Panels and Energy Effects

OpenAIRE