Method for screening prevention and control measures and technologies based on groundwater pollution intensity assessment.

Science.gov (United States)

Li, Juan; Yang, Yang; Huan, Huan; Li, Mingxiao; Xi, Beidou; Lv, Ningqing; Wu, Yi; Xie, Yiwen; Li, Xiang; Yang, Jinjin

2016-05-01

This paper presents a system for determining the evaluation and gradation indices of groundwater pollution intensity (GPI). Considering the characteristics of the vadose zone and pollution sources, the system decides which anti-seepage measures should be implemented at the contaminated site. The pollution sources hazards (PSH) and groundwater intrinsic vulnerability (GIV) are graded by the revised Nemerow Pollution Index and an improved DRTAS model, respectively. GPI is evaluated and graded by a double-sided multi-factor coupling model, which is constructed by the matrix method. The contaminated sites are categorized as prior, ordinary, or common sites. From the GPI results, we develop guiding principles for preventing and removing pollution sources, procedural interruption and remediation, and end treatment and monitoring. Thus, we can select appropriate prevention and control technologies (PCT). To screen the technological schemes and optimize the traditional analytical hierarchy process (AHP), we adopt the technique for order preference by the similarity to ideal solution (TOPSIS) method. Our GPI approach and PCT screening are applied to three types of pollution sites: the refuse dump of a rare earth mine development project (a potential pollution source), a chromium slag dump, and a landfill (existing pollution sources). These three sites are identified as ordinary, prior, and ordinary sites, respectively. The anti-seepage materials at the refuse dump should perform as effectively as a 1.5-m-thick clay bed. The chromium slag dump should be preferentially treated by soil flushing and in situ chemical remediation. The landfill should be treated by natural attenuation technology. The proposed PCT screening approach was compared with conventional screening methods results at the three sites and proved feasible and effective. The proposed method can provide technical support for the monitoring and management of groundwater pollution in China. Copyright © 2015

Designing a good life: a matrix for the technological mediation of morality.

Science.gov (United States)

Swierstra, Tsjalling; Waelbers, Katinka

2012-03-01

Technologies fulfill a social role in the sense that they influence the moral actions of people, often in unintended and unforeseen ways. Scientists and engineers are already accepting much responsibility for the technological, economical and environmental aspects of their work. This article asks them to take an extra step, and now also consider the social role of their products. The aim is to enable engineers to take a prospective responsibility for the future social roles of their technologies by providing them with a matrix that helps to explore in advance how emerging technologies might plausibly affect the reasons behind people's (moral) actions. On the horizontal axis of the matrix, we distinguished the three basic types of reasons that play a role in practical judgment: what is the case, what can be done and what should be done. On the vertical axis we distinguished the morally relevant classes of issues: stakeholders, consequences and the good life. To illustrate how this matrix may work in practice, the final section applies the matrix to the case of the Google PowerMeter. © The Author(s) 2010. This article is published with open access at Springerlink.com

Microseed matrix screening for optimization in protein crystallization: what have we learned?

Science.gov (United States)

D'Arcy, Allan; Bergfors, Terese; Cowan-Jacob, Sandra W; Marsh, May

2014-09-01

Protein crystals obtained in initial screens typically require optimization before they are of X-ray diffraction quality. Seeding is one such optimization method. In classical seeding experiments, the seed crystals are put into new, albeit similar, conditions. The past decade has seen the emergence of an alternative seeding strategy: microseed matrix screening (MMS). In this strategy, the seed crystals are transferred into conditions unrelated to the seed source. Examples of MMS applications from in-house projects and the literature include the generation of multiple crystal forms and different space groups, better diffracting crystals and crystallization of previously uncrystallizable targets. MMS can be implemented robotically, making it a viable option for drug-discovery programs. In conclusion, MMS is a simple, time- and cost-efficient optimization method that is applicable to many recalcitrant crystallization problems.

Screening Technologies for Target Identification in Pancreatic Cancer

Energy Technology Data Exchange (ETDEWEB)

Michl, Patrick, E-mail: michlp@med.uni-marburg.de; Ripka, Stefanie; Gress, Thomas; Buchholz, Malte [Department of Gastroenterology and Endocrinology, University Hospital, Philipps-University Marburg, Baldinger Strasse, D-35043 Marburg (Germany)

2010-12-29

Pancreatic cancer exhibits an extraordinarily high level of resistance to almost any kind of systemic therapy evaluated in clinical trials so far. Therefore, the identification of novel therapeutic targets is urgently required. High-throughput screens have emerged as an important tool to identify putative targets for diagnosis and therapy in an unbiased manner. More than a decade ago, microarray technology was introduced to identify differentially expressed genes in pancreatic cancer as compared to normal pancreas, chronic pancreatitis and other cancer types located in close proximity to the pancreas. In addition, proteomic screens have facilitated the identification of differentially secreted proteins in body fluids of pancreatic cancer patients, serving as possible biomarkers. Recently, RNA interference-based loss-of-function screens have been used to identify functionally relevant genes, whose knock-down has impact on pancreatic cancer cell viability, thereby representing potential new targets for therapeutic intervention. This review summarizes recent results of transcriptional, proteomic and functional screens in pancreatic cancer and discusses potentials and limitations of the respective technologies as well as their impact on future therapeutic developments.

Screening Technologies for Target Identification in Pancreatic Cancer

International Nuclear Information System (INIS)

Michl, Patrick; Ripka, Stefanie; Gress, Thomas; Buchholz, Malte

2010-01-01

Pancreatic cancer exhibits an extraordinarily high level of resistance to almost any kind of systemic therapy evaluated in clinical trials so far. Therefore, the identification of novel therapeutic targets is urgently required. High-throughput screens have emerged as an important tool to identify putative targets for diagnosis and therapy in an unbiased manner. More than a decade ago, microarray technology was introduced to identify differentially expressed genes in pancreatic cancer as compared to normal pancreas, chronic pancreatitis and other cancer types located in close proximity to the pancreas. In addition, proteomic screens have facilitated the identification of differentially secreted proteins in body fluids of pancreatic cancer patients, serving as possible biomarkers. Recently, RNA interference-based loss-of-function screens have been used to identify functionally relevant genes, whose knock-down has impact on pancreatic cancer cell viability, thereby representing potential new targets for therapeutic intervention. This review summarizes recent results of transcriptional, proteomic and functional screens in pancreatic cancer and discusses potentials and limitations of the respective technologies as well as their impact on future therapeutic developments

Using 3 × 3 Matrix to Evaluate the Manufacturing Technology in Food Company

Directory of Open Access Journals (Sweden)

Ingaldi Manuela

2016-06-01

Full Text Available In order to produce goods of sufficient quality finding buyers in the market, a company must have an adequate knowledge of their production technology. Technologies and finished products at the same time will affect the position of the company in the market and hence its existence in this market. Therefore, it is so important for every company to determine the appropriate technological strategy. The 3 × 3 matrix is a very useful tool to do so. This matrix shows the relation between technological possibilities of the company and its position in the market. However, that requires changing the scale used in the matrix. In practice, this means that both those that have a positive impact on the company and those that have a negative impact on it can be included in the factors. The research was conducted in a food industry company. It turned out that the research company was located in field of the matrix marked as ‚Improve marketing’. It means that the company should put more emphasis on improving the factors related to its position in the market.

Remediation Technologies Screening Matrix and Reference Guide, Second Edition

Science.gov (United States)

1994-10-01

grained sand and guar gum gel is then injected as the fracture grows away from the well. After pumping, the sand grains hold the fracture open...Administration OSW EPA Office of Solid Waste OSWER EPA Office of Solid Waste and Emergency Response PACT Powdered -Activated Carbon Technology PAH...binder, and ammonium perchlorate (AP) oxidizer, and a powdered aluminum (Al) fuel; or Hazard Class 1.1 composites, which are based on a nitrate

Touch Screen Technology Adoption and Utilisation by Educators in Early Childhood Educational Institutions

DEFF Research Database (Denmark)

Plumb, Melinda; Kautz, Karlheinz; Tootell, Holly

2013-01-01

The adoption of information and communication technology (ICT) in early childhood educational settings, in particular touch screen technology such as interactive whiteboards and tablet computing devices has potential for use within early childhood educational institutions. We conducted a literature...... that can support the successful implementation of touch screen technology within early childhood educational institutions....... in regards to touch screen technology in early childhood, particularly from a process perspective, and suggest that further research is required to understand the interplay between individual actions and organisational structural influences. This will contribute to the development of an understanding...

Compilation of Existing Neutron Screen Technology

Directory of Open Access Journals (Sweden)

N. Chrysanthopoulou

2014-01-01

Full Text Available The presence of fast neutron spectra in new reactors is expected to induce a strong impact on the contained materials, including structural materials, nuclear fuels, neutron reflecting materials, and tritium breeding materials. Therefore, introduction of these reactors into operation will require extensive testing of their components, which must be performed under neutronic conditions representative of those expected to prevail inside the reactor cores when in operation. Due to limited availability of fast reactors, testing of future reactor materials will mostly take place in water cooled material test reactors (MTRs by tailoring the neutron spectrum via neutron screens. The latter rely on the utilization of materials capable of absorbing neutrons at specific energy. A large but fragmented experience is available on that topic. In this work a comprehensive compilation of the existing neutron screen technology is attempted, focusing on neutron screens developed in order to locally enhance the fast over thermal neutron flux ratio in a reactor core.

SUMA Technology and Newborn Screening Tests for Inherited Metabolic Diseases in Cuba

Directory of Open Access Journals (Sweden)

Ernesto Carlos González Reyes PhD

2016-07-01

Full Text Available The ultramicroanalytic system (SUMA, created in the 1980s, is a complete system of reagents and instrumentation to perform ultramicroassays combining the sensitivity of the micro-enzyme-linked immunosorbent assay (ELISA tests with the use of ultramicrovolumes. This technology permitted establishing large-scale newborn screening programs (NSPs for metabolic and endocrine disorders in Cuba. This article summarizes the main results of the implementation during the 30 years of SUMA technology in NSP for 5 inherited metabolic diseases, using ultramicroassays developed at the Department of Newborn Screening at the Immunoassay Center. Since 1986, SUMA technology has been used in the Cuban NSP for congenital hypothyroidism, initially studying thyroid hormone in cord serum samples. In 2000, a decentralized program for the detection of hyperphenylalaninemias using heel dried blood samples was initiated. These successful experiences permitted including protocols for screening congenital adrenal hyperplasia, galactosemia, and biotinidase deficiency in 2005. A program for the newborn screening of CH using the thyroid-stimulating hormone Neonatal ultramicro-ELISA was fully implemented in 2010. Nowadays, the NSP is supported by a network of 175 SUMA laboratories. After 30 years, more than 3.8 million Cuban newborns have been screened, and 1002 affected children have been detected. Moreover, SUMA technology has been presented in Latin America for over 2 decades and has contributed to screen around 17 million newborns. These results prove that developing countries can develop appropriate diagnostic technologies for making health care accessible to all.

Orbitrap technology for comprehensive metabolite-based liquid chromatographic–high resolution-tandem mass spectrometric urine drug screening – Exemplified for cardiovascular drugs

International Nuclear Information System (INIS)

Helfer, Andreas G.; Michely, Julian A.; Weber, Armin A.; Meyer, Markus R.; Maurer, Hans H.

2015-01-01

LC–high resolution (HR)-MS well established in proteomics has become more and more important in bioanalysis of small molecules over the last few years. Its high selectivity and specificity provide best prerequisites for its use in broad screening approaches. Therefore, Orbitrap technology was tested for developing a general metabolite-based LC–HR-MS/MS screening approach for urinalysis of drugs necessary in clinical and forensic toxicology. After simple urine precipitation, the drugs and their metabolites were separated within 10 min and detected by a Q-Exactive mass spectrometer in full scan with positive/negative switching, and subsequent data dependent acquisition (DDA) mode. Identification criteria were the presence of accurate precursor ions, isotopic patterns, five most intense fragment ions, and comparison with full HR-MS/MS library spectra. The current library contains over 1900 parent drugs and 1200 metabolites. The method was validated for typical drug representatives and metabolites concerning recovery, matrix effects, process efficiency, and limits showed acceptable results. The applicability was tested first for cardiovascular drugs, which should be screened for in poisoning cases and for medication adherence of hypertension patients. The novel LC–HR-MS/MS method allowed fast, simple, and robust urine screening, particularly for cardiovascular drugs showing the usefulness of Orbitrap technology for drug testing. - Highlights: • First study on the application of Orbitrap technology for comprehensive drug screening in clinical and forensic toxicology. • Simple workup, sufficient separation, and powerful screening and identification using modern high resolution MS. • Validation of the assay according to guidelines for qualitative approaches. • Elucidation of the power of new data evaluation software in combination with a new reference drug and metabolite library. • Great relevance for science and practice in clinical and forensic

Orbitrap technology for comprehensive metabolite-based liquid chromatographic–high resolution-tandem mass spectrometric urine drug screening – Exemplified for cardiovascular drugs

Energy Technology Data Exchange (ETDEWEB)

Helfer, Andreas G.; Michely, Julian A.; Weber, Armin A.; Meyer, Markus R.; Maurer, Hans H., E-mail: hans.maurer@uks.eu

2015-09-03

LC–high resolution (HR)-MS well established in proteomics has become more and more important in bioanalysis of small molecules over the last few years. Its high selectivity and specificity provide best prerequisites for its use in broad screening approaches. Therefore, Orbitrap technology was tested for developing a general metabolite-based LC–HR-MS/MS screening approach for urinalysis of drugs necessary in clinical and forensic toxicology. After simple urine precipitation, the drugs and their metabolites were separated within 10 min and detected by a Q-Exactive mass spectrometer in full scan with positive/negative switching, and subsequent data dependent acquisition (DDA) mode. Identification criteria were the presence of accurate precursor ions, isotopic patterns, five most intense fragment ions, and comparison with full HR-MS/MS library spectra. The current library contains over 1900 parent drugs and 1200 metabolites. The method was validated for typical drug representatives and metabolites concerning recovery, matrix effects, process efficiency, and limits showed acceptable results. The applicability was tested first for cardiovascular drugs, which should be screened for in poisoning cases and for medication adherence of hypertension patients. The novel LC–HR-MS/MS method allowed fast, simple, and robust urine screening, particularly for cardiovascular drugs showing the usefulness of Orbitrap technology for drug testing. - Highlights: • First study on the application of Orbitrap technology for comprehensive drug screening in clinical and forensic toxicology. • Simple workup, sufficient separation, and powerful screening and identification using modern high resolution MS. • Validation of the assay according to guidelines for qualitative approaches. • Elucidation of the power of new data evaluation software in combination with a new reference drug and metabolite library. • Great relevance for science and practice in clinical and forensic

Improving clinical outcomes in psychiatric care with touch-screen technology.

Science.gov (United States)

Newnham, Elizabeth A; Doyle, Emma L; Sng, Adelln A H; Hooke, Geoffrey R; Page, Andrew C

2012-05-01

Patient-focused research, which uses clinical characteristics to predict outcomes, is a field in which information technology has been effectively integrated with practice. The present research used touch-screen technology to monitor the daily self-report measures of 1,308 consecutive inpatients and day patients participating in a 2-week cognitive-behavioral therapy group. Providing regular feedback was effective in reducing symptoms for patients at risk of poor outcomes (Newnham, Hooke, & Page, 2010b). The use of touch screens in psychiatric monitoring encourages a collaborative dialogue between patients and therapists and promotes engagement in the process of progress monitoring and treatment evaluation.

NEW METHODS FOR IMPLANT MATRIX FORMATION BASED ON ELECTROSPINNING AND BIOPRINTING TECHNOLOGIES

Directory of Open Access Journals (Sweden)

V. N. Vasilets

2009-01-01

Full Text Available New implant materials for regenerative and replacement surgery based on biodegradable polymers like collagens and polyoxybutirates are developed. Porous structures with controllable morphology were formed from biodegradable polymers using electrospinning and bioprinting technologies. The matrixes were studied by visible and electron scanning microscopy as well as INTEGRA Tomo scanning probe platform making possible the restoration of inner 3D structure of polymer matrix. 

Large scale meta-analysis of fragment-based screening campaigns: privileged fragments and complementary technologies.

Science.gov (United States)

Kutchukian, Peter S; Wassermann, Anne Mai; Lindvall, Mika K; Wright, S Kirk; Ottl, Johannes; Jacob, Jaison; Scheufler, Clemens; Marzinzik, Andreas; Brooijmans, Natasja; Glick, Meir

2015-06-01

A first step in fragment-based drug discovery (FBDD) often entails a fragment-based screen (FBS) to identify fragment "hits." However, the integration of conflicting results from orthogonal screens remains a challenge. Here we present a meta-analysis of 35 fragment-based campaigns at Novartis, which employed a generic 1400-fragment library against diverse target families using various biophysical and biochemical techniques. By statistically interrogating the multidimensional FBS data, we sought to investigate three questions: (1) What makes a fragment amenable for FBS? (2) How do hits from different fragment screening technologies and target classes compare with each other? (3) What is the best way to pair FBS assay technologies? In doing so, we identified substructures that were privileged for specific target classes, as well as fragments that were privileged for authentic activity against many targets. We also revealed some of the discrepancies between technologies. Finally, we uncovered a simple rule of thumb in screening strategy: when choosing two technologies for a campaign, pairing a biochemical and biophysical screen tends to yield the greatest coverage of authentic hits. © 2014 Society for Laboratory Automation and Screening.

Aqueous zymography screening of matrix metalloproteinase activity and inhibition based on colorimetric gold nanoparticles.

Science.gov (United States)

Chuang, Yao-Chen; Huang, Wei-Ting; Chiang, Pin-Hsuan; Tang, Meng-Che; Lin, Chih-Sheng

2012-02-15

An optical gold nanoparticles (AuNPs)-based method was fabricated for the rapid detection of matrix metalloproteinase (MMP) activity and screening potential MMP inhibitors without sophisticated instruments. The diagnosis platform was composed of AuNPs, particular MMP substrates and 6-mercapto-1-hexanol (MCH). The functionalized AuNPs were subjected to specific MMP digestion, and the MMP found the substrate on AuNPs, such that the AuNPs lost shelter and MCH increased the attraction force between AuNPs. Consequently, AuNPs aggregation and a color change from red to purple with increasing MMP concentration were observed. The surface plasmon resonance (SPR) of the formed AuNPs allowed for the quantitative detection of MMP activity. A sensitive linear correlation existed between the absorbance and the activity of the MMPs, which ranged from 10 ng/mL to 700 ng/mL in NTTC buffer and plasma samples. The proposed colorimetric method could be accomplished in a homogeneous solution with one-step operation in 30 min and has been successfully applied to the determination of particular MMP activity in plasma samples, in which the results are consistent with substrate zymography. This technology may become a simple platform for parallel screening a number of inhibitors and offer an alternative method to studying the efficiency of inhibitors for suppressing MMP activity. The absorbance ratio at 625 nm and 525 nm (A(625)/A(525)) confirmed the efficiency of the inhibitors as observed in substrate zymography. The IC(50) of ONO-4817 and galardin for MMP-1, MMP-2 and MMP-7 determined by the proposed colorimetric method was similar to the results of substrate zymography. Crown Copyright © 2011. Published by Elsevier B.V. All rights reserved.

Screening applications in drug discovery based on microfluidic technology

Science.gov (United States)

Eribol, P.; Uguz, A. K.; Ulgen, K. O.

2016-01-01

Microfluidics has been the focus of interest for the last two decades for all the advantages such as low chemical consumption, reduced analysis time, high throughput, better control of mass and heat transfer, downsizing a bench-top laboratory to a chip, i.e., lab-on-a-chip, and many others it has offered. Microfluidic technology quickly found applications in the pharmaceutical industry, which demands working with leading edge scientific and technological breakthroughs, as drug screening and commercialization are very long and expensive processes and require many tests due to unpredictable results. This review paper is on drug candidate screening methods with microfluidic technology and focuses specifically on fabrication techniques and materials for the microchip, types of flow such as continuous or discrete and their advantages, determination of kinetic parameters and their comparison with conventional systems, assessment of toxicities and cytotoxicities, concentration generations for high throughput, and the computational methods that were employed. An important conclusion of this review is that even though microfluidic technology has been in this field for around 20 years there is still room for research and development, as this cutting edge technology requires ingenuity to design and find solutions for each individual case. Recent extensions of these microsystems are microengineered organs-on-chips and organ arrays. PMID:26865904

Screening applications in drug discovery based on microfluidic technology.

Science.gov (United States)

Eribol, P; Uguz, A K; Ulgen, K O

2016-01-01

Microfluidics has been the focus of interest for the last two decades for all the advantages such as low chemical consumption, reduced analysis time, high throughput, better control of mass and heat transfer, downsizing a bench-top laboratory to a chip, i.e., lab-on-a-chip, and many others it has offered. Microfluidic technology quickly found applications in the pharmaceutical industry, which demands working with leading edge scientific and technological breakthroughs, as drug screening and commercialization are very long and expensive processes and require many tests due to unpredictable results. This review paper is on drug candidate screening methods with microfluidic technology and focuses specifically on fabrication techniques and materials for the microchip, types of flow such as continuous or discrete and their advantages, determination of kinetic parameters and their comparison with conventional systems, assessment of toxicities and cytotoxicities, concentration generations for high throughput, and the computational methods that were employed. An important conclusion of this review is that even though microfluidic technology has been in this field for around 20 years there is still room for research and development, as this cutting edge technology requires ingenuity to design and find solutions for each individual case. Recent extensions of these microsystems are microengineered organs-on-chips and organ arrays.

76 FR 45645 - 10-Day Notice of Proposed Information Collection: Technology Security/Clearance Plans, Screening...

Science.gov (United States)

2011-07-29

...: Technology Security/Clearance Plans, Screening Records, and Non-Disclosure Agreements ACTION: Notice of... Information Collection: Technology Security/ Clearance Plans, Screening Records, and Non-Disclosure Agreements...: None. Respondents: Business and Nonprofit Organizations, Foreign Governments. Estimated Number of...

TfR Binding Peptide Screened by Phage Display Technology ...

African Journals Online (AJOL)

Purpose: To screen an hTfR affinity peptide and investigate its activity in vitro. Methods: hTfR ... Keywords: Peptide, hTfR, Transferrin receptor, Phage display technology, Enhanced green ..... mediated uptake of peptides that bind the human.

Current status and application of fine screening technology in China

Science.gov (United States)

Chernova, E. V.; Chernov, D. V.

2017-10-01

The paper presents data on the design and technical parameters of high frequency vibrating screens, which are produced by Chinese manufacturer - company Landsky Tech Ltd. The technology of high frequency vibration is widely used at mining and metallurgical industries to separate fine and ultra-fine particles from the flow of dry material or pulp. The paper contains different types of screening systems, description, advantages and disadvantages of equipment and test results from mineral processing plants.

Extending the Global Dialogue about Media, Technology, Screen Time, and Young Children

Science.gov (United States)

Ernest, James M.; Causey, Cora; Newton, Allison B.; Sharkins, Kimberly; Summerlin, Jennifer; Albaiz, Najla

2014-01-01

Questions about the potential benefits and dangers of media and technology use abound, with competing theories regarding its effects among young children. This article explores global perspectives on children's exposure to media, technology, and screen time (MeTS) in the schools, homes, and communities of an increasingly technology-driven world.…

Cost-Effectiveness of Old and New Technologies for Aneuploidy Screening.

Science.gov (United States)

Sinkey, Rachel G; Odibo, Anthony O

2016-06-01

Cost-effectiveness analyses allow assessment of whether marginal gains from new technology are worth increased costs. Several studies have examined cost-effectiveness of Down syndrome (DS) screening and found it to be cost-effective. Noninvasive prenatal screening also appears to be cost-effective among high-risk women with respect to DS screening, but not for the general population. Chromosomal microarray (CMA) is a genetic sequencing method superior to but more expensive than karyotype. In light of CMAs greater ability to detect genetic abnormalities, it is cost-effective when used for prenatal diagnosis of an anomalous fetus. This article covers methodology and salient issues of cost-effectiveness. Copyright © 2016 Elsevier Inc. All rights reserved.

Using CUDA Technology for Defining the Stiffness Matrix in the Subspace of Eigenvectors

Directory of Open Access Journals (Sweden)

Yu. V. Berchun

2015-01-01

Full Text Available The aim is to improve the performance of solving a problem of deformable solid mechanics through the use of GPGPU. The paper describes technologies for computing systems using both a central and a graphics processor and provides motivation for using CUDA technology as the efficient one.The paper also analyses methods to solve the problem of defining natural frequencies and design waveforms, i.e. an iteration method in the subspace. The method includes several stages. The paper considers the most resource-hungry stage, which defines the stiffness matrix in the subspace of eigenforms and gives the mathematical interpretation of this stage.The GPU choice as a computing device is justified. The paper presents an algorithm for calculating the stiffness matrix in the subspace of eigenforms taking into consideration the features of input data. The global stiffness matrix is very sparse, and its size can reach tens of millions. Therefore, it is represented as a set of the stiffness matrices of the single elements of a model. The paper analyses methods of data representation in the software and selects the best practices for GPU computing.It describes the software implementation using CUDA technology to calculate the stiffness matrix in the subspace of eigenforms. Due to the input data nature, it is impossible to use the universal libraries of matrix computations (cuSPARSE and cuBLAS for loading the GPU. For efficient use of GPU resources in the software implementation, the stiffness matrices of elements are built in the block matrices of a special form. The advantages of using shared memory in GPU calculations are described.The transfer to the GPU computations allowed a twentyfold increase in performance (as compared to the multithreaded CPU-implementation on the model of middle dimensions (degrees of freedom about 2 million. Such an acceleration of one stage speeds up defining the natural frequencies and waveforms by the iteration method in a subspace

X-231B technology demonstration for in situ treatment of contaminated soil: Technology evaluation and screening

International Nuclear Information System (INIS)

Siegrist, R.L.; Morris, M.I.; Donaldson, T.L.; Palumbo, A.V.; Herbes, S.E.; Jenkins, R.A.; Morrissey, C.M.; Harris, M.T.

1993-08-01

The Portsmouth Gaseous Diffusion Plant (Ports) is located approximately 70 miles south of Columbus in southern Ohio. Among the several waste management units on the facility, the X-231B unit consists of two adjacent oil biodegradation plots. The plots encompass ∼ 0.8 acres and were reportedly used from 1976 to 1983 for the treatment and disposal of waste oils and degreasing solvents, some containing uranium-235 and technetium-99. The X-231B unit is a regulated solid waste management unit (SWMU) under the Resource Conservation and Recovery Act (RCRA). The X-231B unit is also a designated SWMU located within Quadrant I of the site as defined in an ongoing RCRA Facilities Investigation and Corrective Measures Study (RFI/CMS). Before implementing one or more Technology Demonstration Project must be completed. The principal goal of this project was to elect and successfully demonstrate one ore more technologies for effective treatment of the contaminated soils associated with the X-231B unit at PORTS. The project was divided into two major phases. Phase 1 involved a technology evaluation and screening process. The second phase (i.e., Phase 2) was to involve field demonstration, testing and evaluation of the technology(s) selected during Phase 1. This report presents the methods, results, and conclusions of the technology evaluation and screening portion of the project

Small Screen Technology Use among Indigenous Boarding School Adolescents from Remote Regions of Western Australia

Science.gov (United States)

Johnson, Genevieve Marie; Oliver, Rhonda

2014-01-01

The uptake of small screen technology by adolescents is widespread, particularly in industrial nations. Whether the same is true for Australian Aboriginal youth is less clear as there is a dearth of research in this regard. Therefore, in this exploratory study the use of small screen technology by Indigenous students was examined. Twenty-four…

Technology Addiction among Treatment Seekers for Psychological Problems: Implication for Screening in Mental Health Setting.

Science.gov (United States)

Das, Aswathy; Sharma, Manoj Kumar; Thamilselvan, P; Marimuthu, P

2017-01-01

Technology usage has seen an increase among users. The usage varies from social, personal, and psychological reasons. Users are frequently using to overcome mood states as well as to manage the other psychological states. This work is going to explore the information technology use among subjects with a psychiatric disorder. A total of 75 subjects were assessed using background data sheet, internet addiction impairment index, video game use pattern, pornography addiction screening tool and screening for mobile phone use, from in-patient and out-patient setting of tertiary mental health setting. It showed the presence of addiction to mobile, internet, video game, and pornography. Age was found to be negatively correlated with this addiction. Average usage time had been associated with management of mood states. The addiction to information technology had been associated with a delay in initiation of sleep. This work has implication for screening technology addiction among subjects seeking treatment for psychological problems and motivate them to develop the healthy use of technology.

Pharmacological screening technologies for venom peptide discovery.

Science.gov (United States)

Prashanth, Jutty Rajan; Hasaballah, Nojod; Vetter, Irina

2017-12-01

Venomous animals occupy one of the most successful evolutionary niches and occur on nearly every continent. They deliver venoms via biting and stinging apparatuses with the aim to rapidly incapacitate prey and deter predators. This has led to the evolution of venom components that act at a number of biological targets - including ion channels, G-protein coupled receptors, transporters and enzymes - with exquisite selectivity and potency, making venom-derived components attractive pharmacological tool compounds and drug leads. In recent years, plate-based pharmacological screening approaches have been introduced to accelerate venom-derived drug discovery. A range of assays are amenable to this purpose, including high-throughput electrophysiology, fluorescence-based functional and binding assays. However, despite these technological advances, the traditional activity-guided fractionation approach is time-consuming and resource-intensive. The combination of screening techniques suitable for miniaturization with sequence-based discovery approaches - supported by advanced proteomics, mass spectrometry, chromatography as well as synthesis and expression techniques - promises to further improve venom peptide discovery. Here, we discuss practical aspects of establishing a pipeline for venom peptide drug discovery with a particular emphasis on pharmacology and pharmacological screening approaches. This article is part of the Special Issue entitled 'Venom-derived Peptides as Pharmacological Tools.' Copyright © 2017 Elsevier Ltd. All rights reserved.

Awareness, Interest, and Preferences of Primary Care Providers in Using Point-of-Care Cancer Screening Technology.

Science.gov (United States)

Kim, Chloe S; Vanture, Sarah; Cho, Margaret; Klapperich, Catherine M; Wang, Catharine; Huang, Franklin W

2016-01-01

Well-developed point-of-care (POC) cancer screening tools have the potential to provide better cancer care to patients in both developed and developing countries. However, new medical technology will not be adopted by medical providers unless it addresses a population's existing needs and end-users' preferences. The goals of our study were to assess primary care providers' level of awareness, interest, and preferences in using POC cancer screening technology in their practice and to provide guidelines to biomedical engineers for future POC technology development. A total of 350 primary care providers completed a one-time self-administered online survey, which took approximately 10 minutes to complete. A $50 Amazon gift card was given as an honorarium for the first 100 respondents to encourage participation. The description of POC cancer screening technology was provided in the beginning of the survey to ensure all participants had a basic understanding of what constitutes POC technology. More than half of the participants (57%) stated that they heard of the term "POC technology" for the first time when they took the survey. However, almost all of the participants (97%) stated they were either "very interested" (68%) or "somewhat interested" (29%) in using POC cancer screening technology in their practice. Demographic characteristics such as the length of being in the practice of medicine, the percentage of patients on Medicaid, and the average number of patients per day were not shown to be associated with the level of interest in using POC. These data show that there is a great interest in POC cancer screening technology utilization among this population of primary care providers and vast room for future investigations to further understand the interest and preferences in using POC cancer technology in practice. Ensuring that the benefits of new technology outweigh the costs will maximize the likelihood it will be used by medical providers and patients.

Development and Implementation of High School Chemistry Modules Using Touch-Screen Technologies

Science.gov (United States)

Lewis, Maurica S.; Zhao, Jinhui; Montclare, Jin Kim

2012-01-01

Technology was employed to motivate and captivate students while enriching their in-class education. An outreach program is described that involved college mentors introducing touch-screen technology into a high school chemistry classroom. Three modules were developed, with two of them specifically tailored to encourage comprehension of molecular…

Intra and Inter-Rater Reliability of Screening for Movement Impairments: Movement Control Tests from The Foundation Matrix

Science.gov (United States)

Mischiati, Carolina R.; Comerford, Mark; Gosford, Emma; Swart, Jacqueline; Ewings, Sean; Botha, Nadine; Stokes, Maria; Mottram, Sarah L.

2015-01-01

Pre-season screening is well established within the sporting arena, and aims to enhance performance and reduce injury risk. With the increasing need to identify potential injury with greater accuracy, a new risk assessment process has been produced; The Performance Matrix (battery of movement control tests). As with any new method of objective testing, it is fundamental to establish whether the same results can be reproduced between examiners and by the same examiner on consecutive occasions. This study aimed to determine the intra-rater test re-test and inter-rater reliability of tests from a component of The Performance Matrix, The Foundation Matrix. Twenty participants were screened by two experienced musculoskeletal therapists using nine tests to assess the ability to control movement during specific tasks. Movement evaluation criteria for each test were rated as pass or fail. The therapists observed participants real-time and tests were recorded on video to enable repeated ratings four months later to examine intra-rater reliability (videos rated two weeks apart). Overall test percentage agreement was 87% for inter-rater reliability; 98% Rater 1, 94% Rater 2 for test re-test reliability; and 75% for real-time versus video. Intraclass-correlation coefficients (ICCs) were excellent between raters (0.81) and within raters (Rater 1, 0.96; Rater 2, 0.88) but poor for real-time versus video (0.23). Reliability for individual components of each test was more variable: inter-rater, 68-100%; intra-rater, 88-100% Rater 1, 75-100% Rater 2; and real-time versus video 31-100%. Cohen’s Kappa values for inter-rater reliability were 0.0-1.0; intra-rater 0.6-1.0 for Rater 1; -0.1-1.0 for Rater 2; and -0.1-1 for real-time versus video. It is concluded that both inter and intra-rater reliability of tests in The Foundation Matrix are acceptable when rated by experienced therapists. Recommendations are made for modifying some of the criteria to improve reliability where

Using NFC technology for fast-tracking large-siza multi-touch screens

OpenAIRE

Muñoz-Organero, Mario; Opoku, Samuel King

2011-01-01

Multi-touch technology interfaces are becoming ubiquitous since their integration in smart-phones, tablets and many consumer electronics devices. Depending on the size of the tangible interface, the computing resource restrictions and the resolution required, there are different technological alternatives for multi-touch screens such as camera based systems, capacity, resistive or pressure sensing systems or LED based systems. This paper presents a different alternative to d...

Awareness, Interest, and Preferences of Primary Care Providers in Using Point-of-Care Cancer Screening Technology.

Directory of Open Access Journals (Sweden)

Chloe S Kim

Full Text Available Well-developed point-of-care (POC cancer screening tools have the potential to provide better cancer care to patients in both developed and developing countries. However, new medical technology will not be adopted by medical providers unless it addresses a population's existing needs and end-users' preferences. The goals of our study were to assess primary care providers' level of awareness, interest, and preferences in using POC cancer screening technology in their practice and to provide guidelines to biomedical engineers for future POC technology development. A total of 350 primary care providers completed a one-time self-administered online survey, which took approximately 10 minutes to complete. A $50 Amazon gift card was given as an honorarium for the first 100 respondents to encourage participation. The description of POC cancer screening technology was provided in the beginning of the survey to ensure all participants had a basic understanding of what constitutes POC technology. More than half of the participants (57% stated that they heard of the term "POC technology" for the first time when they took the survey. However, almost all of the participants (97% stated they were either "very interested" (68% or "somewhat interested" (29% in using POC cancer screening technology in their practice. Demographic characteristics such as the length of being in the practice of medicine, the percentage of patients on Medicaid, and the average number of patients per day were not shown to be associated with the level of interest in using POC. These data show that there is a great interest in POC cancer screening technology utilization among this population of primary care providers and vast room for future investigations to further understand the interest and preferences in using POC cancer technology in practice. Ensuring that the benefits of new technology outweigh the costs will maximize the likelihood it will be used by medical providers and

Case study: technology initiative led to advanced lead optimization screening processes at Bristol-Myers Squibb, 2004-2009.

Science.gov (United States)

Zhang, Litao; Cvijic, Mary Ellen; Lippy, Jonathan; Myslik, James; Brenner, Stephen L; Binnie, Alastair; Houston, John G

2012-07-01

In this paper, we review the key solutions that enabled evolution of the lead optimization screening support process at Bristol-Myers Squibb (BMS) between 2004 and 2009. During this time, technology infrastructure investment and scientific expertise integration laid the foundations to build and tailor lead optimization screening support models across all therapeutic groups at BMS. Together, harnessing advanced screening technology platforms and expanding panel screening strategy led to a paradigm shift at BMS in supporting lead optimization screening capability. Parallel SAR and structure liability relationship (SLR) screening approaches were first and broadly introduced to empower more-rapid and -informed decisions about chemical synthesis strategy and to broaden options for identifying high-quality drug candidates during lead optimization. Copyright © 2012 Elsevier Ltd. All rights reserved.

Preparation of milk samples for immunoassay and liquid chromatographic screening using matrix solid-phase dispersion.

Science.gov (United States)

Barker, S A; Long, A R

1994-01-01

The use of drugs to maintain the health and maximize the output of dairy cattle has made the monitoring of milk for such agents essential. Screening tests based on immunological, microbial inhibition, and bacterial receptor assays have been developed for the detection of violative levels of therapeutic substances. However, such assays are not infallible, and false positive or negative results can occur when contaminants bind receptors or compete for the binding of the target residues. Such effects may arise from dietary sources, diseases, or other variables. Thus, a violation by such a test is not definitive until further confirmation is obtained. Our laboratory has developed extraction procedures for several drugs used in dairy production. Our method uses matrix solid-phase dispersion (MSPD) to isolate drugs away from contaminants and to eliminate many possible interferences. MSPD can also be used to enhance the specificity of such assays by fractionating various classes of drugs that may cross-react. Similarly, such methods may be used for liquid chromatographic screening and confirmation of a suspect sample.

Weak cation magnetic separation technology and MALDI-TOF-MS in screening serum protein markers in primary type I osteoporosis.

Science.gov (United States)

Shi, X L; Li, C W; Liang, B C; He, K H; Li, X Y

2015-11-30

We investigated weak cation magnetic separation technology and matrix-assisted laser desorption ionization-time of flight-mass spectrometry (MALDI-TOF-MS) in screening serum protein markers of primary type I osteoporosis. We selected 16 postmenopausal women with osteoporosis and nine postmenopausal women as controls to find a new method for screening biomarkers and establishing a diagnostic model for primary type I osteoporosis. Serum samples were obtained from controls and patients. Serum protein was extracted with the WCX protein chip system; protein fingerprints were examined using MALDI-TOF-MS. The preprocessed and model construction data were handled by the ProteinChip system. The diagnostic models were established using a genetic arithmetic model combined with a support vector machine (SVM). The SVM model with the highest Youden index was selected. Combinations with the highest accuracy in distinguishing different groups of data were selected as potential biomarkers. From the two groups of serum proteins, 123 cumulative MS protein peaks were selected. Significant intensity differences in the protein peaks of 16 postmenopausal women with osteoporosis were screened. The difference in Youden index between the four groups of protein peaks showed that the highest peaks had mass-to-charge ratios of 8909.047, 8690.658, 13745.48, and 15114.52. A diagnosis model was established with these four markers as the candidates, and the model specificity and sensitivity were found to be 100%. Two groups of specimens in the SVM results on the scatterplot were distinguishable. We established a diagnosis model, and provided a new serological method for screening and diagnosis of osteoporosis with high sensitivity and specificity.

ABCD Matrix Method a Case Study

CERN Document Server

Seidov, Zakir F; Yahalom, Asher

2004-01-01

In the Israeli Electrostatic Accelerator FEL, the distance between the accelerator's end and the wiggler's entrance is about 2.1 m, and 1.4 MeV electron beam is transported through this space using four similar quadrupoles (FODO-channel). The transfer matrix method (ABCD matrix method) was used for simulating the beam transport, a set of programs is written in the several programming languages (MATHEMATICA, MATLAB, MATCAD, MAPLE) and reasonable agreement is demonstrated between experimental results and simulations. Comparison of ABCD matrix method with the direct "numerical experiments" using EGUN, ELOP, and GPT programs with and without taking into account the space-charge effects showed the agreement to be good enough as well. Also the inverse problem of finding emittance of the electron beam at the S1 screen position (before FODO-channel), by using the spot image at S2 screen position (after FODO-channel) as function of quad currents, is considered. Spot and beam at both screens are described as tilted eel...

Improving NASA's technology transfer process through increased screening and evaluation in the information dissemination program

Science.gov (United States)

Laepple, H.

1979-01-01

The current status of NASA's technology transfer system can be improved if the technology transfer process is better understood. This understanding will only be gained if a detailed knowledge about factors generally influencing technology transfer is developed, and particularly those factors affecting technology transfer from government R and D agencies to industry. Secondary utilization of aerospace technology is made more difficult because it depends on a transfer process which crosses established organizational lines of authority and which is outside well understood patterns of technical applications. In the absence of a sound theory about technology transfer and because of the limited capability of government agencies to explore industry's needs, a team approach to screening and evaluation of NASA generated technologies is proposed which calls for NASA, and other organizations of the private and public sectors which influence the transfer of NASA generated technology, to participate in a screening and evaluation process to determine the commercial feasibility of a wide range of technical applications.

Infant Imitation from Television Using Novel Touch Screen Technology

Science.gov (United States)

Zack, Elizabeth; Barr, Rachel; Gerhardstein, Peter; Dickerson, Kelly; Meltzoff, Andrew N.

2009-01-01

Infants learn less from a televised demonstration than from a live demonstration, the "video deficit effect." The present study employs a novel approach, using touch screen technology to examine 15-month olds' transfer of learning. Infants were randomly assigned either to within-dimension (2D/2D or 3D/3D) or cross-dimension (3D/2D or 2D/3D)…

The model for the strategic management of technology. The improvement cycle and matrixes deployment QFD

International Nuclear Information System (INIS)

Benavides Velasco, C. A.; Quintana Garcia, C.

2007-01-01

In spite of the importance of innovative firms, few contributions study in depth the strategic management of their technological resources. After describing the process of strategic management of technology, we propose a model that enables the application of that process and guarantees organizational flexibility in technological companies. For it, such a process has been adapted to She wart cycle (Deeming wheel) and combined with the quality function deployment (QFD). As a result, we propose the improvement cycle of technology. It contains two matrixes that allow identifying and prioritizing with greater clarity the activities related to the management of technological resources. (Authors)

Fragment-based lead generation: identification of seed fragments by a highly efficient fragment screening technology

Science.gov (United States)

Neumann, Lars; Ritscher, Allegra; Müller, Gerhard; Hafenbradl, Doris

2009-08-01

For the detection of the precise and unambiguous binding of fragments to a specific binding site on the target protein, we have developed a novel reporter displacement binding assay technology. The application of this technology for the fragment screening as well as the fragment evolution process with a specific modelling based design strategy is demonstrated for inhibitors of the protein kinase p38alpha. In a fragment screening approach seed fragments were identified which were then used to build compounds from the deep-pocket towards the hinge binding area of the protein kinase p38alpha based on a modelling approach. BIRB796 was used as a blueprint for the alignment of the fragments. The fragment evolution of these deep-pocket binding fragments towards the fully optimized inhibitor BIRB796 included the modulation of the residence time as well as the affinity. The goal of our study was to evaluate the robustness and efficiency of our novel fragment screening technology at high fragment concentrations, compare the screening data with biochemical activity data and to demonstrate the evolution of the hit fragments with fast kinetics, into slow kinetic inhibitors in an in silico approach.

English Language Screening for Scientific Staff at Delft University of Technology,

NARCIS (Netherlands)

Klaassen, R.G.; Bos, M.H.P.C.

2010-01-01

Delft University of Technology (DUT) screened her (non-native English) scientific staff on their level of English proficiency in the academic year of 2006/2007. In this paper this large scale operation, involving planning, policy decisions, assessment means, advice and training are discussed. Since

Using label-free screening technology to improve efficiency in drug discovery.

Science.gov (United States)

Halai, Reena; Cooper, Matthew A

2012-02-01

Screening assays have traditionally utilized reporter labels to quantify biological responses relevant to the disease state of interest. However, there are limitations associated with the use of labels that may be overcome with temporal measurements possible with label-free. This review comprises general and system-specific information from literature searches using PubMed, published books and the authors' personal experience. This review highlights the label-free approaches in the context of various applications. The authors also note technical issues relevant to the development of label-free assays and their application to HTS. The limitations associated with the use of transfected cell lines and the use of label-based assays are gradually being realized. As such, greater emphasis is being placed on label-free biophysical techniques using native cell lines. The introduction of 96- and 384-well plate label-free systems is helping to broker a wider acceptance of these approaches in high-throughput screening. However, potential users of the technologies remain skeptical, primarily because the physical basis of the signals generated, and their contextual relevance to cell biology and signal transduction, has not been fully elucidated. Until this is done, these new technology platforms are more likely to complement, rather than replace, traditional screening platforms.

The development of high-content screening (HCS) technology and its importance to drug discovery.

Science.gov (United States)

Fraietta, Ivan; Gasparri, Fabio

2016-01-01

High-content screening (HCS) was introduced about twenty years ago as a promising analytical approach to facilitate some critical aspects of drug discovery. Its application has spread progressively within the pharmaceutical industry and academia to the point that it today represents a fundamental tool in supporting drug discovery and development. Here, the authors review some of significant progress in the HCS field in terms of biological models and assay readouts. They highlight the importance of high-content screening in drug discovery, as testified by its numerous applications in a variety of therapeutic areas: oncology, infective diseases, cardiovascular and neurodegenerative diseases. They also dissect the role of HCS technology in different phases of the drug discovery pipeline: target identification, primary compound screening, secondary assays, mechanism of action studies and in vitro toxicology. Recent advances in cellular assay technologies, such as the introduction of three-dimensional (3D) cultures, induced pluripotent stem cells (iPSCs) and genome editing technologies (e.g., CRISPR/Cas9), have tremendously expanded the potential of high-content assays to contribute to the drug discovery process. Increasingly predictive cellular models and readouts, together with the development of more sophisticated and affordable HCS readers, will further consolidate the role of HCS technology in drug discovery.

Rigorous Screening Technology for Identifying Suitable CO2 Storage Sites II

Energy Technology Data Exchange (ETDEWEB)

George J. Koperna Jr.; Vello A. Kuuskraa; David E. Riestenberg; Aiysha Sultana; Tyler Van Leeuwen

2009-06-01

This report serves as the final technical report and users manual for the 'Rigorous Screening Technology for Identifying Suitable CO2 Storage Sites II SBIR project. Advanced Resources International has developed a screening tool by which users can technically screen, assess the storage capacity and quantify the costs of CO2 storage in four types of CO2 storage reservoirs. These include CO2-enhanced oil recovery reservoirs, depleted oil and gas fields (non-enhanced oil recovery candidates), deep coal seems that are amenable to CO2-enhanced methane recovery, and saline reservoirs. The screening function assessed whether the reservoir could likely serve as a safe, long-term CO2 storage reservoir. The storage capacity assessment uses rigorous reservoir simulation models to determine the timing, ultimate storage capacity, and potential for enhanced hydrocarbon recovery. Finally, the economic assessment function determines both the field-level and pipeline (transportation) costs for CO2 sequestration in a given reservoir. The screening tool has been peer reviewed at an Electrical Power Research Institute (EPRI) technical meeting in March 2009. A number of useful observations and recommendations emerged from the Workshop on the costs of CO2 transport and storage that could be readily incorporated into a commercial version of the Screening Tool in a Phase III SBIR.

A SIMPLE AND RAPID MATRIX-ASSISTED LASER DESORPTION/IONIZATION TIME OF FLIGHT MASS SPECTROMETRY METHOD TO SCREEN FISH PLASMA SAMPLES FOR ESTROGEN-RESPONSIVE BIOMARKERS

Science.gov (United States)

In this study, we describe and evaluate the performance of a simple and rapid mass spectral method for screening fish plasma for estrogen-responsive biomarkers using matrix assisted laster desorption/ionization time of flight mass spectrometry (MALDI-TOF-MS) couopled with a short...

Cost comparison of laboratory methods and four field screening technologies for uranium-contaminated soil

International Nuclear Information System (INIS)

Douthat, D.M.; Armstrong, A.Q.

1994-01-01

To address the problem of characterizing uranium-contaminated surface soil at federal facilities, the Department of Energy has the development of four uranium field screening technologies, under the direction of the Uranium-in-Soils Integrated Demonstration (USID) Program. These four technologies include: a long-range alpha detector a beta scintillation detector, an in situ gamma detector, and a mobile laser ablation-inductively coupled plasma/atomic emission spectrometry (LA-ICP/AES) laboratory. As part of the performance assessment for these field screening technologies, cost estimates for the development and operation of each technology were created. A cost study was conducted to compare three of the USID field screening technologies to the use of traditional field surveying equipment to adequately characterize surface soils of a one-acre site. The results indicate that the use of traditional equipment costs more than the in situ gamma detector, but less than the beta scintillation detector and LRAD. The use of traditional field surveying equipment results in cost savings of 4% and 34% over the use of the beta scintillation and LRAD technologies, respectively. A study of single-point surface soil sampling and laboratory analysis costs was also conducted. Operational costs of the mobile LA-ICP/AES laboratory were compared with operational costs of traditional sampling and analysis, which consists of collecting soil samples and conducting analysis in a radiochemical laboratory. The cost study indicates that the use of the mobile LA-ICP/AES laboratory results in cost savings of 23% and 40% over traditional field sampling and laboratory analysis conducted by characterization groups at two DOE facilities

Processing of novel bioactive polymeric matrixes for tissue engineering using supercritical fluid technology

Energy Technology Data Exchange (ETDEWEB)

Duarte, Ana Rita C., E-mail: aduarte@dep.uminho.pt [3B' s Research Group, Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4806-909 Taipas, Guimaraes (Portugal); IBB, Institute for Biotechnology and Bioengineering, PT Government Associated Laboratory, Guimaraes (Portugal); Caridade, Sofia G.; Mano, Joao F.; Reis, Rui L. [3B' s Research Group, Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4806-909 Taipas, Guimaraes (Portugal); IBB, Institute for Biotechnology and Bioengineering, PT Government Associated Laboratory, Guimaraes (Portugal)

2009-08-31

The aim of this study was to develop a new process for the production of bioactive 3D scaffolds using a clean and environmentally friendly technology. The possibility of preparing composite scaffolds of Bioglass and a polymeric blend of starch and poly(L-lactic acid) (SPLA50) was evaluated. Supercritical phase-inversion technique was used to prepare inorganic particles loaded starch-based porous composite matrixes in a one-step process for bone tissue engineering purposes. Due to their osteoconductive properties some glasses and ceramics are interesting materials to be used for bone tissue engineering purposes; however their poor mechanical properties create the need of a polymeric support where the inorganic fraction can be dispersed. Samples impregnated with different concentrations of Bioglass (10 and 15% wt/wt polymer) were prepared at 200 bar and 55 deg. C. The presence of Bioglass did not affect the porosity or interconnectivity of the polymeric matrixes. Dynamic mechanical analysis has proven that the modulus of the SPLA50 scaffolds increases when glass particles are impregnated within the matrix. In vitro bioactivity studies were carried out using simulated body fluid and the results show that a calcium-phosphate layer started to be formed after only 1 day of immersion. Chemical analysis of the apatite layer formed on the surface of the scaffold was performed by different techniques, namely EDS and FTIR spectroscopy and X-ray diffraction (XRD). The ion concentration in the simulated body fluid was also carried out by ICP analysis. Results suggest that a bone-like apatite layer was formed. This study reports the feasibility of using supercritical fluid technology to process, in one step, a porous matrix loaded with a bioactive material for tissue engineering purposes.

Sensing Technologies for Autism Spectrum Disorder Screening and Intervention

Directory of Open Access Journals (Sweden)

John-John Cabibihan

2016-12-01

Full Text Available This paper reviews the state-of-the-art in sensing technologies that are relevant for Autism Spectrum Disorder (ASD screening and therapy. This disorder is characterized by difficulties in social communication, social interactions, and repetitive behaviors. It is diagnosed during the first three years of life. Early and intensive interventions have been shown to improve the developmental trajectory of the affected children. The earlier the diagnosis, the sooner the intervention therapy can begin, thus, making early diagnosis an important research goal. Technological innovations have tremendous potential to assist with early diagnosis and improve intervention programs. The need for careful and methodological evaluation of such emerging technologies becomes important in order to assist not only the therapists and clinicians in their selection of suitable tools, but to also guide the developers of the technologies in improving hardware and software. In this paper, we survey the literatures on sensing technologies for ASD and we categorize them into eye trackers, movement trackers, electrodermal activity monitors, tactile sensors, vocal prosody and speech detectors, and sleep quality assessment devices. We assess their effectiveness and study their limitations. We also examine the challenges faced by this growing field that need to be addressed before these technologies can perform up to their theoretical potential.

The Strength of Ethical Matrixes as a Tool for Normative Analysis Related to Technological Choices: The Case of Geological Disposal for Radioactive Waste.

Science.gov (United States)

Kermisch, Céline; Depaus, Christophe

2018-02-01

The ethical matrix is a participatory tool designed to structure ethical reflection about the design, the introduction, the development or the use of technologies. Its collective implementation, in the context of participatory decision-making, has shown its potential usefulness. On the contrary, its implementation by a single researcher has not been thoroughly analyzed. The aim of this paper is precisely to assess the strength of ethical matrixes implemented by a single researcher as a tool for conceptual normative analysis related to technological choices. Therefore, the ethical matrix framework is applied to the management of high-level radioactive waste, more specifically to retrievable and non-retrievable geological disposal. The results of this analysis show that the usefulness of ethical matrixes is twofold and that they provide a valuable input for further decision-making. Indeed, by using ethical matrixes, implicit ethically relevant issues were revealed-namely issues of equity associated with health impacts and differences between close and remote future generations regarding ethical impacts. Moreover, the ethical matrix framework was helpful in synthesizing and comparing systematically the ethical impacts of the technologies under scrutiny, and hence in highlighting the potential ethical conflicts.

Developments and the preliminary tests of Resistive GEMs manufactured by a screen printing technology

CERN Document Server

Agócs, G; Oliveira, R; Martinego, P; Peskov, Vladimir; Pietropaolo, P; Picchi, P

2008-01-01

We report promising initial results obtained with new resistive-electrode GEM (RETGEM) detectors manufactured, for the first time, using screen printing technology. These new detectors allow one to reach gas gains nearly as high as with ordinary GEM-like detectors with metallic electrodes; however, due to the high resistivity of its electrodes the RETGEM, in contrast to ordinary hole-type detectors, has the advantage of being fully spark protected. We discovered that RETGEMs can operate stably and at high gains in noble gases and in other badly quenched gases, such as mixtures of noble gases with air and in pure air; therefore, a wide range of practical applications, including dosimetry and detection of dangerous gases, is foreseeable. To promote a better understanding of RETGEM technology some comparative studies were completed with metallic-electrode thick GEMs. A primary benefit of these new RETGEMs is that the screen printing technology is easily accessible to many research laboratories. This accessibilit...

BIG BROTHER IS WATCHING YOU! TO BE OR NOT TO BE ONLINE... OR SCREEN AS OUR OWN TECHNOLOGICAL ADDRESS

Directory of Open Access Journals (Sweden)

Vanda Maria Sousa

2014-12-01

Full Text Available This article seeks to answer the question: how the screens are interposed between the subject and reality, in contexts of the New Technologies of Information and Communication, particularly in the case of television screens (in the reality show format and computer screens (by the profusion of social networks? Using the interpretative methodology, our goal is to take as a starting point the etymology of technic and technology to establish the technological nature of man’s relationship with reality. Once this premise is demonstrated, we will convene the Heideggerian concepts (dasein and ge-stell to interpret how the technology of the screen meets a social need for happiness that comes from the media in a world that re-discovers itself as iconic. Each of us is called upon, in our day-to-day life, to an important, special and urgent meeting with the representation of our own selves, against a screen, where will be its own place of happiness. We intend to assess whether ideologies are hiper-evaluated today, especially when translating reality into binary conceptions of the world, projecting dasein on the demand for unity (1, opposing it to failure (0, each time using the screen more like a mirror or a window, and forgetting its function as a ge-stell by making it a promotion, and not doing it as a way to discover dasein, but, instead, as the opening of the simulacra itself.

Weak cation exchange magnetic beads coupled with matrix-assisted laser desorption ionization-time of flight-mass spectrometry in screening serum protein markers in osteopenia.

Science.gov (United States)

He, Wei-Tao; Liang, Bo-Cheng; Shi, Zhen-Yu; Li, Xu-Yun; Li, Chun-Wen; Shi, Xiao-Lin

2016-01-01

The present study aimed at investigating the weak cation magnetic separation technology and matrix-assisted laser desorption ionization-time of flight-mass spectrometry (MALDI-TOF-MS) in screening serum protein markers of osteopenia from ten postmenopausal women and ten postmenopausal women without osteopenia as control group, to find a new method for screening biomarkers and establishing a diagnostic model for primary type I osteoporosis. Serum samples were collected from postmenopausal women with osteopenia and postmenopausal women with normal bone mass. Proteins were extracted from serum samples by weak cation exchange magnetic beads technology, and mass spectra acquisition was done by MALDI-TOF-MS. The visualization and comparison of data sets, statistical peak evaluation, model recognition, and discovery of biomarker candidates were handled by the proteinchip data analysis system software(ZJU-PDAS). The diagnostic models were established using genetic arithmetic based support vector machine (SVM). The SVM result with the highest Youden Index was selected as the model. Combinatorial Peaks having the highest accuracy in distinguishing different samples were selected as potential biomarker. From the two group serum samples, a total of 133 differential features were selected. Ten features with significant intensity differences were screened. In the pair-wise comparisons, processing of MALDI-TOF spectra resulted in the identification of ten differential features between postmenopausal women with osteopenia and postmenopausal women with normal bone mass. The difference of features by Youden index showed that the highest features had a mass to charge ratio of 1699 and 3038 Da. A diagnosis model was established with these two peaks as the candidate marker, and the specificity of the model is 100 %, the sensitivity was 90 % by leave-one-out cross validation test. The two groups of specimens in SVM results on the scatter plot could be clearly distinguished. The peak

Development of a diffuse element matrix in 'planar' technology. A particular application: logical gate with coupled emitter

International Nuclear Information System (INIS)

Rousseau, P.

1968-01-01

In a first part, after a brief recall concerning 'planar' technology we discuss the various parasitic elements associated with integrated circuits components. Mathematical formulae of these elements are derived. In a second part, we present a matrix of 22 transistors and 12 resistors which has been realized. This matrix enables the integration of the major part of nuclear circuits. Some of the obtained circuits are shown, particularly an emitter coupled logic gate which presents good electrical behaviour. (author) [fr

STUDY OF HORIZONTAL SCREEN STRENGTH CREATED BY INJECTION TECHNOLOGY CEMENT BINDER BASED

Directory of Open Access Journals (Sweden)

BORISOV A. A.

2016-09-01

Full Text Available Annotation. Formulation of the problem. An important indicator in the planning of injection works is a particle size distribution of the soil and the very composition of injection. The ideal case is to comply with the injection optimum ratio between the size of particles in solution and injectable medium. This ratio corresponds to complete impregnation of the environment. Today in the field of building technologies known classical methods of grouting with the injection process [9]. This may be a cementation or silicification with different chemical compositions. Due to the fact that we have proposed an innovative technology of impervious curtain device, special attention should be paid to the performance and physical and mechanical properties of the resulting soil-injection. This is due to the fact that the proposed technology provides for lesser known technical solutions, the use of which should ultimately result in impervious screens with desired properties. Goal. The aim of this study is to investigate the properties of the resulting soil-concrete impervious screen. Such structures should have defined a number of physical and mechanical properties. In this paper, it was of interest to study the compressive strength of the resulting soil-concrete structure. Conclusion. As a result of experimentation and implementation of complex obtained experimentally-statistical models that describe the main soil-quality indicators. Based on these data is possible optimal selection of formulation and technological structure for sandy soils with different modules size of its particles.

Moving beyond Screen Time: Redefining Developmentally Appropriate Technology Use in Early Childhood Education. Policy Brief

Science.gov (United States)

Daugherty, Lindsay; Dossani, Rafiq; Johnson, Erin-Elizabeth; Wright, Cameron

2014-01-01

Conversations about what constitutes "developmentally appropriate" use of technology in early childhood education have, to date, focused largely on a single, blunt measure--screen time--that fails to capture important nuances, such as what type of media a child is accessing and whether technology use is taking place solo or with peers.…

Overview of DOE's field screening technology development activities

International Nuclear Information System (INIS)

Frank, C.W.; Anderson, T.D.; Cooley, C.R.; Hain, K.E.; Lien, S.C.T.; Erickson, M.D.

1991-01-01

The Department of Energy (DOE) has recently created the Office of Environmental Restoration and Waste Management, into which it consolidated those activities. Within this new organization, the Office of Technology Development (OTD) is responsible for research, development, demonstration, testing, and evaluation (RDDT ampersand E) activities aimed at meeting DOE cleanup goals, while minimizing cost and risk. Site characterization using traditional drilling, sampling, and analytical methods comprises a significant part of the environmental restoration efforts in terms of both cost and time to accomplish. It can also be invasive and create additional pathways for spread of contaminants. Consequently, DOE is focusing on site characterization as one of the areas in which significant technological advances are possible which will decrease cost, reduce risk, and shorten schedules for achieving restoration goals. DOE is investing considerably in R ampersand D and demonstration activities which will improve the abilities to screen chemical, radiological, and physical parameters in the field. This paper presents an overview of the program objectives and status and reviews some of the projects which are currently underway in the area. 1 ref

Bioprinting 3D cell-laden hydrogel microarray for screening human periodontal ligament stem cell response to extracellular matrix

International Nuclear Information System (INIS)

Ma, Yufei; Ji, Yuan; Huang, Guoyou; Zhang, Xiaohui; Xu, Feng; Ling, Kai

2015-01-01

Periodontitis is an inflammatory disease negatively affecting up to 15% of adults worldwide. Periodontal ligament stem cells (PDLSCs) hold great promises for periodontal tissue regeneration, where it is necessary to find proper extracellular matrix (ECM) materials (e.g., composition, concentration). In this study, we proposed a bioprinting-based approach to generate nano-liter sized three-dimensional (3D) cell-laden hydrogel array with gradient of ECM components, through controlling the volume ratio of two hydrogels, such as gelatin methacrylate (GelMA) and poly(ethylene glycol) (PEG) dimethacrylate. The resulting cell-laden array with a gradient of GelMA/PEG composition was used to screen human PDLSC response to ECM. The behavior (e.g., cell viability, spreading) of human PDLSCs in GelMA/PEG array were found to be depended on the volume ratios of GelMA/PEG, with cell viability and spreading area decreased along with increasing the ratio of PEG. The developed approach would be useful for screening cell-biomaterial interaction in 3D and promoting regeneration of functional tissue. (paper)

e-Health technologies for adult hearing screening

Directory of Open Access Journals (Sweden)

S. Stenfelt

2011-03-01

Full Text Available The development of hearing diagnosis methods and hearing screening methods are not isolated phenomena: they are intimately related to changes in the cultural background and to advances in fields of medicine and engineering. In the recent years, there has been a rapid evolution in the development of fast, easy and reliable techniques for lowcost hearing screening initiatives. Since adults and elderly people typically experience a reduced hearing ability in challenging listening situations [e.g., in background noise, in reverberation, or with competing speech (Pichora‑Fuller & Souza, 2003], these newly developed screening tests mainly rely on the recognition of speech stimuli in noise, so that the real experienced listening difficulties can be effectively targeted (Killion & Niquette, 2000. New tests based on the recognition of speech in noise are being developed on portable, battery- operated devices (see, for example, Paglialonga et al., 2011, or distributed diffusely using information and communication technologies. The evolutions of e-Health and telemedicine have shifted focus from patients coming to the hearing clinic for hearing health evaluation towards the possibility of evaluating the hearing status remotely at home. So far, two ways of distributing the hearing test have primarily been used: ordinary telephone networks (excluding mobile networks and the internet. When using the telephone network for hearing screening, the predominantly test is a speech-in-noise test often referred to as the digit triplet test where the subjects hearing status is evaluated as the speech-to-noise threshold for spoken digits. This test is today available in some ten countries in Europe, North America and Australia. The use of internet as testing platform allows several different types of hearing assessment tests such as questionnaires, different types of speech in noise tests, temporal gap detection, sound localization (minimum audible angle, and spectral

Integrated economic and experimental framework for screening of primary recovery technologies for high cell density CHO cultures.

Science.gov (United States)

Popova, Daria; Stonier, Adam; Pain, David; Titchener-Hooker, Nigel J; Farid, Suzanne S

2016-07-01

Increases in mammalian cell culture titres and densities have placed significant demands on primary recovery operation performance. This article presents a methodology which aims to screen rapidly and evaluate primary recovery technologies for their scope for technically feasible and cost-effective operation in the context of high cell density mammalian cell cultures. It was applied to assess the performance of current (centrifugation and depth filtration options) and alternative (tangential flow filtration (TFF)) primary recovery strategies. Cell culture test materials (CCTM) were generated to simulate the most demanding cell culture conditions selected as a screening challenge for the technologies. The performance of these technology options was assessed using lab scale and ultra scale-down (USD) mimics requiring 25-110mL volumes for centrifugation and depth filtration and TFF screening experiments respectively. A centrifugation and depth filtration combination as well as both of the alternative technologies met the performance selection criteria. A detailed process economics evaluation was carried out at three scales of manufacturing (2,000L, 10,000L, 20,000L), where alternative primary recovery options were shown to potentially provide a more cost-effective primary recovery process in the future. This assessment process and the study results can aid technology selection to identify the most effective option for a specific scenario. © 2016 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Clinical Implications of Technological Advances in Screening for Atrial Fibrillation.

Science.gov (United States)

Singh, Nikhil; Chun, Sung; Hadley, David; Froelicher, Victor

The incidence of atrial fibrillation (AF) continues to increase worldwide as people live longer. AF is the leading cause of stroke among patients older than 75 years and is responsible for at least 15% of all strokes. Industry has responded to this problem with a plethora of monitoring devices. These include single lead ECG adhesive sensors, implantable loop recorders, smartphone attachments and wearables. This review will concentrate on clinical studies using these technologies. There are wearables including watches and watch-like devices that will be mentioned but these have not been validated for clinical use. This review will begin with a background regarding screening for AF and at the end present findings from Cardiac Implantable devices that could influence use of the new mobile health technologies. Copyright © 2018 Elsevier Inc. All rights reserved.

Well screening for matrix stimulation treatments

International Nuclear Information System (INIS)

Saavedra, N; Solano, R; Gidley, J; Reyes, C.A; Rodriguez; Kondo, F; Hernandez, J

1998-01-01

Matrix acidizing is a stimulation technique only applicable to wells with surrounding damage. It is therefore very important to differentiate the real formation damage from the damage caused by flow Ni dynamic effects. The mechanical damage corresponds to flow restrictions caused by partial penetration, poor perforation as well as to reduce diameters of the production tubing. The dynamic effects are generated by inertia caused by high flow rates and high-pressure differentials. A common practice in our oil fields is to use a general formulation as acid treatment, most of the times without previous lab studies that guarantee the applicability of the treatment in the formation. Additionally, stimulation is randomly applied even treating undamaged wells with negative results and in the best of the cases, loss of the treatment. The selection of the well for matrix stimulation is an essential factor for the success of the treatment. Selection is done through the evaluation of the skin factor (S) and of the economic benefits of reducing the skin in comparison to the cost of the work. The most appropriate tool for skin evaluation is a good pressure test where the radial flow period can be identified. Nevertheless, we normally find-outdated tests most of the times taken with inaccurate tools. The interpretation problem is worsened by completions in which there is simultaneous production from several sand packages and it is difficult to individually differentiate damage factors. This works states a procedure for the selection of wells appropriate for stimulation; it also proposes a method to evaluate the skin factor when there are no accurate interpretations of the pressure tests. A new and increasingly applied methodology to treat wells with high water cuts, which are usually discarded due to the risk of stimulating water zones, is also mentioned

Ecological risk assessment of agricultural soils for the definition of soil screening values: A comparison between substance-based and matrix-based approaches.

Science.gov (United States)

Pivato, Alberto; Lavagnolo, Maria Cristina; Manachini, Barbara; Vanin, Stefano; Raga, Roberto; Beggio, Giovanni

2017-04-01

The Italian legislation on contaminated soils does not include the Ecological Risk Assessment (ERA) and this deficiency has important consequences for the sustainable management of agricultural soils. The present research compares the results of two ERA procedures applied to agriculture (i) one based on the "substance-based" approach and (ii) a second based on the "matrix-based" approach. In the former the soil screening values (SVs) for individual substances were derived according to institutional foreign guidelines. In the latter, the SVs characterizing the whole-matrix were derived originally by the authors by means of experimental activity. The results indicate that the "matrix-based" approach can be efficiently implemented in the Italian legislation for the ERA of agricultural soils. This method, if compared to the institutionalized "substance based" approach is (i) comparable in economic terms and in testing time, (ii) is site specific and assesses the real effect of the investigated soil on a battery of bioassays, (iii) accounts for phenomena that may radically modify the exposure of the organisms to the totality of contaminants and (iv) can be considered sufficiently conservative.

A Wearable Textile 2D Touchpad Sensor Based on Screen-Printing Technology.

Science.gov (United States)

Ferri, Josue; Lidón-Roger, Jose Vicente; Moreno, Jorge; Martinez, Gabriel; Garcia-Breijo, Eduardo

2017-12-20

Among many of the designs used in the detection of 2D gestures for portable technology, the touchpad is one of the most complex and with more functions to implement. Its development has undergone a great push due to its use in displays, but it is not widely used with other technologies. Its application on textiles could allow a wide range of applications in the field of medicine, sports, etc. Obtaining a flexible, robust touchpad with good response and low cost is one of the objectives of this work. A textile touchpad based on a diamond pattern design using screen printing technology has been developed. This technology is widely used in the textile industry and therefore does not require heavy investments. The developed prototypes were analyzed using a particular controller for projected capacitive technologies (pro-cap), which is the most used in gesture detection. Two different designs were used to obtain the best configuration, obtaining a good result in both cases.

A Stretchable Radio-Frequency Strain Sensor Using Screen Printing Technology.

Science.gov (United States)

Jeong, Heijun; Lim, Sungjoon

2016-11-02

In this paper, we propose a stretchable radio-frequency (RF) strain sensor fabricated with screen printing technology. The RF sensor is designed using a half-wavelength patch that resonates at 3.7 GHz. The resonant frequency is determined by the length of the patch, and it therefore changes when the patch is stretched. Polydimethylsiloxane (PDMS) is used to create the substrate, because of its stretchable and screen-printable surface. In addition, Dupont PE872 (Dupont, NC, American) silver conductive ink is used to create the stretchable conductive patterns. The sensor performance is demonstrated both with full-wave simulations and with measurements carried out on a fabricated sample. When the length of the patch sensor is increased by a 7.8% stretch, the resonant frequency decreases from 3.7 GHz to 3.43 GHz, evidencing a sensitivity of 3.43 × 10⁷ Hz/%. Stretching the patch along its width does not change the resonant frequency.

The Matrix Organization Revisited

DEFF Research Database (Denmark)

Gattiker, Urs E.; Ulhøi, John Parm

1999-01-01

This paper gives a short overview of matrix structure and technology management. It outlines some of the characteristics and also points out that many organizations may actualy be hybrids (i.e. mix several ways of organizing to allocate resorces effectively).......This paper gives a short overview of matrix structure and technology management. It outlines some of the characteristics and also points out that many organizations may actualy be hybrids (i.e. mix several ways of organizing to allocate resorces effectively)....

Luminescent screens

International Nuclear Information System (INIS)

Lu, C.-I.

1982-01-01

Luminescent screens which are useful for such purposes as intensifying screens for radiographs are comprised of a support bearing a layer of finely divided particles of a phosphor dispersed in a cross-linked polymeric matrix formed by heat-curing of a coating composition comprising an unsaturated cross-linkable polymer, a polymerizable acrylic monomer, a thermoplastic polyurethane elastomer, and a heat-activatable polymerization initiator. The phosphor layer includes voids formed by evaporation of an evaporable component which is present in the coating composition from which such layer is formed. (author)

A Stretchable Electromagnetic Absorber Fabricated Using Screen Printing Technology.

Science.gov (United States)

Jeong, Heijun; Lim, Sungjoon

2017-05-21

A stretchable electromagnetic absorber fabricated using screen printing technology is proposed in this paper. We used a polydimethylsiloxane (PDMS) substrate to fabricate the stretchable absorber since PDMS exhibits good dielectric properties, flexibility, and restoring capabilities. DuPont PE872 (DuPont, Wilmington, CT, USA), a stretchable silver conductive ink, was used for the screen printing technique. The reflection coefficient of the absorber was measured using a vector network analyzer and a waveguide. The proposed absorber was designed as a rectangular patch unit cell, wherein the top of the unit cell acted as the patch and the bottom formed the ground. The size of the patch was 8 mm × 7 mm. The prototype of the absorber consisted of two unit cells such that it fits into the WR-90 waveguide (dimensions: 22.86 mm × 10.16 mm) for experimental measurement. Before stretching the absorber, the resonant frequency was 11 GHz. When stretched along the x -direction, the resonant frequency shifted by 0.1 GHz, from 11 to 10.9 GHz, demonstrating 99% absorption. Furthermore, when stretched along the y -direction, the resonant frequency shifted by 0.6 GHz, from 11 to 10.4 GHz, demonstrating 99% absorption.

Computational Screening of MOF-Based Mixed Matrix Membranes for CO2/N2 Separations

Directory of Open Access Journals (Sweden)

Zeynep Sumer

2016-01-01

Full Text Available Atomically detailed simulations were used to examine CO2/N2 separation potential of metal organic framework- (MOF- based mixed matrix membranes (MMMs in this study. Gas permeability and selectivity of 700 new MMMs composed of 70 different MOFs and 10 different polymers were calculated for CO2/N2 separation. This is the largest number of MOF-based MMMs for which computational screening is done to date. Selecting the appropriate MOFs as filler particles in polymers resulted in MMMs that have higher CO2/N2 selectivities and higher CO2 permeabilities compared to pure polymer membranes. We showed that, for polymers that have low CO2 permeabilities but high CO2 selectivities, the identity of the MOF used as filler is not important. All MOFs enhanced the CO2 permeabilities of this type of polymers without changing their selectivities. Several MOF-based MMMs were identified to exceed the upper bound established for polymers. The methods we introduced in this study will create many opportunities to select the MOF/polymer combinations with useful properties for CO2 separation applications.

Assessment and Comparison of Vitreous Humor as an Alternative Matrix for Forensic Toxicology Screening by GC-MS.

Science.gov (United States)

Metushi, Imir G; Fitzgerald, Robert L; McIntyre, Iain M

2016-05-01

Alternative specimens have been occasionally considered as substitutes for whole blood for postmortem toxicology testing. We studied the applicability of vitreous humor, and evaluated whether it would be suitable to replace (or augment) whole blood for routine drug screening. Results showed that from 51 autopsy cases, we were able to identify an aggregate of 209 findings in whole blood compared with 169 in vitreous. The total number of compounds identified was 71 for whole blood and 60 for vitreous humor. Quantitative analysis showed that whole-blood concentrations of trazodone were several fold higher than vitreous humor concentrations (1.42 ± 0.57 vs. 0.15 ± 0.05 mg/L, respectively) and similar results were also obtained for diazepam (0.37 ± 0.06 vs. 0.13 ± 0.01, respectively). For other drugs such as oxycodone, hydrocodone and doxylamine, a trend suggesting higher concentrations in vitreous humor vs. whole blood was observed; however, this was not significant. Our results are consistent with the limited work of other investigators, and suggest that vitreous humor could be an appropriate matrix for drug screening in postmortem toxicology. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Optical Encoding Technology for Viral Screening Panels Final Report CRADA No TC02132.0

Energy Technology Data Exchange (ETDEWEB)

Lenhoff, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haushalter, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-08-15

This was a collaborative effort between Lawrence Livermore National Security, LLC, Lawrence Livermore National Laboratory (LLNL) and Parallel Synthesis Technologies, Inc. (PSTI), to develop Optical Encoding Technology for Viral Screening Panels. The goal for this effort was to prepare a portable bead reader system that would enable the development of viral and bacterial screening panels which could be used for the detection of any desired set of bacteria or viruses in any location. The main objective was to determine if the combination of a bead-based, PCR suspension array technology, formulated from Parallume encoded beads and PSTI’s multiplex assay reader system (MARS), could provide advantages in terms of the number of simultaneously measured samples, portability, ruggedness, ease of use, accuracy, precision or cost as compared to the Luminexbased system developed at LLNL. The project underwent several no cost extensions however the overall goal of demonstrating the utility of this new system was achieved. As a result of the project a significant change to the type of bead PSTI used for the suspension system was implemented allowing better performance than the commercial Luminex system.

Can Coolness Predict Technology Adoption? Effects of Perceived Coolness on User Acceptance of Smartphones with Curved Screens.

Science.gov (United States)

Kim, Ki Joon; Shin, Dong-Hee; Park, Eunil

2015-09-01

This study proposes an acceptance model for curved-screen smartphones, and explores how the sense of coolness induced by attractiveness, originality, subcultural appeal, and the utility of the curved screen promotes smartphone adoption. The results of structural equation modeling analyses (N = 246) show that these components of coolness (except utility) increase the acceptance of the technology by enhancing the smartphones' affectively driven qualities rather than their utilitarian ones. The proposed coolness model is then compared with the original technology acceptance model to validate that the coolness factors are indeed equally effective determinants of usage intention, as are the extensively studied usability factors such as perceived ease of use and usefulness.

iScreen: Image-Based High-Content RNAi Screening Analysis Tools.

Science.gov (United States)

Zhong, Rui; Dong, Xiaonan; Levine, Beth; Xie, Yang; Xiao, Guanghua

2015-09-01

High-throughput RNA interference (RNAi) screening has opened up a path to investigating functional genomics in a genome-wide pattern. However, such studies are often restricted to assays that have a single readout format. Recently, advanced image technologies have been coupled with high-throughput RNAi screening to develop high-content screening, in which one or more cell image(s), instead of a single readout, were generated from each well. This image-based high-content screening technology has led to genome-wide functional annotation in a wider spectrum of biological research studies, as well as in drug and target discovery, so that complex cellular phenotypes can be measured in a multiparametric format. Despite these advances, data analysis and visualization tools are still largely lacking for these types of experiments. Therefore, we developed iScreen (image-Based High-content RNAi Screening Analysis Tool), an R package for the statistical modeling and visualization of image-based high-content RNAi screening. Two case studies were used to demonstrate the capability and efficiency of the iScreen package. iScreen is available for download on CRAN (http://cran.cnr.berkeley.edu/web/packages/iScreen/index.html). The user manual is also available as a supplementary document. © 2014 Society for Laboratory Automation and Screening.

Ecological risk assessment of agricultural soils for the definition of soil screening values: A comparison between substance-based and matrix-based approaches

Directory of Open Access Journals (Sweden)

Alberto Pivato

2017-04-01

Full Text Available The Italian legislation on contaminated soils does not include the Ecological Risk Assessment (ERA and this deficiency has important consequences for the sustainable management of agricultural soils. The present research compares the results of two ERA procedures applied to agriculture (i one based on the “substance-based” approach and (ii a second based on the “matrix-based” approach. In the former the soil screening values (SVs for individual substances were derived according to institutional foreign guidelines. In the latter, the SVs characterizing the whole-matrix were derived originally by the authors by means of experimental activity.The results indicate that the “matrix-based” approach can be efficiently implemented in the Italian legislation for the ERA of agricultural soils. This method, if compared to the institutionalized “substance based” approach is (i comparable in economic terms and in testing time, (ii is site specific and assesses the real effect of the investigated soil on a battery of bioassays, (iii accounts for phenomena that may radically modify the exposure of the organisms to the totality of contaminants and (iv can be considered sufficiently conservative. Keyword: Environmental science

Using micropower impulse radar technology to screen for pneumothorax: an international bi-institutional study.

Science.gov (United States)

van der Wilden, Gwendolyn M; Van der Wilden, Gwen; Albers, Christoph E; Albers, Christof; Haefeli, Pascal C; Haefeli, Peter; Zimmermann, Heinz; Zimmerman, Heinz; Exadaktylos, Aristomenis; Exadaktylos, Aris; Levy, Phillip; Birkhan, Oscar; Birkham, Oscar; Michaildou, Maria; Michailidou, Maria; Sideris, Antonios; Velmahos, George C; Velmahos, George; Alam, Hasan B; Alam, Hasan; King, David R; King, David; Fagenholz, Peter J; Fagenholz, Peter; Yeh, D Dante; Yeh, Dante; de Moya, Marc A

2012-12-01

Pneumothoraces (PTXs) are a common entity in thoracic trauma. Micropower impulse radar (MIR) has been able to detect PTXs in surgical patients. However, this technology has not been tested previously on trauma patients. The purpose of this study was to determine the sensitivity and specificity of MIR to detect clinically significant PTXs. We hypothesized that MIR technology can effectively screen trauma patients for clinically significant PTXs. This was a prospective observational study in Level I trauma centers in Boston, Massachusetts, and Bern, Switzerland. All trauma patients undergoing a chest computed tomographic (CT) scan were eligible for the study. Consent was obtained, and readings were performed within 30 minutes before or after the CT scan. The patients had eight lung fields tested (four on each side). The qualitative and quantitative MIR results were blinded and stored on the device. We then compared the results of the MIR to the CT scan and the need for chest tube drainage. We defined PTXs as clinically significant if they required a chest tube. Seventy-five patients were enrolled, with a mean age of 46 ± 16 years. Eighty-four percent were male. The screening test took approximately 1 minute. All but two patients had blunt chest trauma. Six true-positives, 6 false-positives, 63 true-negatives, and 0 false-negatives resulted in an overall sensitivity of 100%. MIR is an easy to use handheld technology that effectively screened patients for clinically significant PTXs, with a sensitivity and negative predictive value of 100%. MIR may be used for rapid, repeatable, and ongoing surveillance of trauma patients. Diagnostic study, level III.

The Evolution of MALDI-TOF Mass Spectrometry toward Ultra-High-Throughput Screening: 1536-Well Format and Beyond.

Science.gov (United States)

Haslam, Carl; Hellicar, John; Dunn, Adrian; Fuetterer, Arne; Hardy, Neil; Marshall, Peter; Paape, Rainer; Pemberton, Michelle; Resemannand, Anja; Leveridge, Melanie

2016-02-01

Mass spectrometry (MS) offers a label-free, direct-detection method, in contrast to fluorescent or colorimetric methodologies. Over recent years, solid-phase extraction-based techniques, such as the Agilent RapidFire system, have emerged that are capable of analyzing samples in high-throughput screening (HTS). Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF) offers an alternative for high-throughput MS detection. However, sample preparation and deposition onto the MALDI target, as well as interference from matrix ions, have been considered limitations for the use of MALDI for screening assays. Here we describe the development and validation of assays for both small-molecule and peptide analytes using MALDI-TOF coupled with nanoliter liquid handling. Using the JMJD2c histone demethylase and acetylcholinesterase as model systems, we have generated robust data in a 1536 format and also increased sample deposition to 6144 samples per target. Using these methods, we demonstrate that this technology can deliver fast sample analysis time with low sample volume, and data comparable to that of current RapidFire assays. © 2015 Society for Laboratory Automation and Screening.

Performance and touch characteristics of disabled and non-disabled participants during a reciprocal tapping task using touch screen technology.

Science.gov (United States)

Irwin, Curt B; Sesto, Mary E

2012-11-01

Touch screens are becoming more prevalent in everyday environments. Therefore, it is important that this technology is accessible to those with varying disabilities. The objective of the current study was to evaluate performance and touch characteristics (forces, impulses, and dwell times) of individuals with and without a movement disorder during a reciprocal tapping touch screen task. Thirty-seven participants with a motor control disability and 15 non-disabled participants participated. Outcome measures include number of correct taps, dwell time, exerted force, and impulse. Results indicate non-disabled participants had 1.8 more taps than participants with fine motor control disabilities and 2.8 times more than those with gross motor impairments (ptouch characteristics exist between those with and without motor control disabilities. Understanding how people (including those with disabilities) interact with touch screens may allow designers and engineers to ultimately improve usability of touch screen technology. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Study On Technology Based Home Vision Screening And Creating Awareness On Eye Health

Directory of Open Access Journals (Sweden)

Nirav Mehta

2015-08-01

Full Text Available Introduction Technology is one of most important factor in todays life. IPAD is leading as people can make use of technology by just pressing buttons. Networking technology and education makes communication easier and helps people in easy education and awareness. Aim amp objectives The main aim of the study is to educate and aware among people regarding eye health and the check the visual function of their eye by using Apple I pad. Material and Methodology The following study is a home based vision screening program using IPAD which uses the basic tests like visual acuity color vision contrast sensitivity and amsler tests for checking the basic functions of the eye. The study was performed in many societies moving from one place to another using IPAD as a tool. Reliability of ipad was checked a pilot study on 25 subjects visual acuity colour vision and contrast sensitivity was taken on both ipad and Original chart like snellen ishihara and pellirobson and compared in which the results and the accuracy were same. The study also contains questionnaire on the awareness and education about eye health. The subjects included in the study were an age group of 10 to 70. Subjects like infants and blind were not included in the study. Results During the study it was observed that there is no significant difference in testing of visual acuity between ipad and Snellen standard chart. The subjects responded actively towards screening and that home vision screening can be possible. During the study it was found that 40 subjects out of 100 needed further detailed check-up and were referred in Rotary eye hospital hospital but only 3 out of 40 came for it. This shows that they are less aware and education about their eye health. Software used in IPAD were visual acuity color vision contrast sensitivity and amsler tests A questionnaire was also asked which indicated less awareness among the common people. Conclusion We examined with just an ipad and not an

Preliminary matrix model for quantifying and balancing the socio-economic impact of alternative cooling system technologies for nuclear power plants

International Nuclear Information System (INIS)

Cleary, D.P.; Salomon, S.N.; Pollnow, L.A.; Spangler, M.B.

1976-01-01

Assessment of environmental, including socio-economic, impacts of alternative technologies or courses of action is made difficult by the inability to adequately quantify the impacts. Matrix methods offer a set of techniques which allows the analyst to compare the relative impacts of alternative technologies or actions. Work is underway to develop and adapt these techniques to be used in assessing the environmental impacts of alternative cooling systems, and other alternative technological and siting options

Fluorescence imaging technology (FI) for high-throughput screening of selenide-modified nano-TiO2 catalysts.

Science.gov (United States)

Wang, Liping; Lee, Jianchao; Zhang, Meijuan; Duan, Qiannan; Zhang, Jiarui; Qi, Hailang

2016-02-18

A high-throughput screening (HTS) method based on fluorescence imaging (FI) was implemented to evaluate the catalytic performance of selenide-modified nano-TiO2. Chemical ink-jet printing (IJP) technology was reformed to fabricate a catalyst library comprising 1405 (Ni(a)Cu(b)Cd(c)Ce(d)In(e)Y(f))Se(x)/TiO2 (M6Se/Ti) composite photocatalysts. Nineteen M6Se/Tis were screened out from the 1405 candidates efficiently.

Providing floating capabilities in latest-generation sand screens

Energy Technology Data Exchange (ETDEWEB)

Bowen, E.G.; Coronado, M.P. [Society of Petroleum Engineers, Richardson, TX (United States)]|[Baker Hughes, Houston, TX (United States)

2008-10-15

Alternative production methods are needed for the massive reserves located in the bitumen region of Canada's tar sands. The area has over 100 installations of sand screens/slotted liners in both injection and production legs using steam-assisted gravity drainage (SAGD) technology. Multiple wells must be drilled from a single pad because of the sensitive nature of the environment. With significant depths of these wells, a floating sand screen provides assurance that the sand screen will reach the desired depth. Paraffin is generally used to plug the flow access of the screen during installation. This paper discussed a new technology that has been developed to allow for sand screen installations without relying on paraffin wax to withstand differential pressure. The new technology uses a hydro-mechanical valving system incorporated into the screen design to temporarily close off the screen while being run in the hole. The paper described how the technology could provide a reliable, time-saving solution for SAGD installations when floating sand control screens are needed. The paper discussed current technology and its limitations, sand screen installation, screen design for floating applications, and additional applications. It was concluded that this technology solution provides a unique alternative to the methods currently used to install sand screens with SAGD technology in the fast growing Canadian market for bitumen recovery. 2 refs., 5 figs.

Identification of dihydrogambogic acid as a matrix metalloproteinase 1 inhibitor by high-throughput screening

Directory of Open Access Journals (Sweden)

Li Y

2017-12-01

Full Text Available Yong Li, John J Voorhees, Gary J FisherDepartment of Dermatology, University of Michigan, Ann Arbor, MI, USAType I collagen (COL1 is the predominant structural protein in the skin. COL1 forms densely packed fibrils which are essential for maintaining skin mechanical properties and youthful appearance.1 The enzyme matrix metalloproteinase-1 (MMP1 cleaves COL1 fibrils at a single site.2 Once cleaved by MMP1, COL1 fibrils can be degraded by other proteases. MMP1 expression is elevated during natural aging and chronic sun exposure, ie, photoaging, leading to excessive degradation of COL1.3 This excessive degradation contributes to COL1 deficiency in the skin of the elderly. COL1 deficiency impairs skin structural integrity and appearance.Given the detrimental role of MMP1 in mediating age-associated fragmentation of COL1 fibrils, it would be beneficial to include MMP1 inhibitors in topical antiaging skin care products. Naturally existing substances that are safe for human use, such as botanical extracts, are often used in skin care products. We have utilized highthroughput screening (HTS to identify naturally existing MMP1 inhibitors that could be used for cosmetic purposes.

COVARIANCE ASSISTED SCREENING AND ESTIMATION.

Science.gov (United States)

Ke, By Tracy; Jin, Jiashun; Fan, Jianqing

2014-11-01

Consider a linear model Y = X β + z , where X = X n,p and z ~ N (0, I n ). The vector β is unknown and it is of interest to separate its nonzero coordinates from the zero ones (i.e., variable selection). Motivated by examples in long-memory time series (Fan and Yao, 2003) and the change-point problem (Bhattacharya, 1994), we are primarily interested in the case where the Gram matrix G = X ' X is non-sparse but sparsifiable by a finite order linear filter. We focus on the regime where signals are both rare and weak so that successful variable selection is very challenging but is still possible. We approach this problem by a new procedure called the Covariance Assisted Screening and Estimation (CASE). CASE first uses a linear filtering to reduce the original setting to a new regression model where the corresponding Gram (covariance) matrix is sparse. The new covariance matrix induces a sparse graph, which guides us to conduct multivariate screening without visiting all the submodels. By interacting with the signal sparsity, the graph enables us to decompose the original problem into many separated small-size subproblems (if only we know where they are!). Linear filtering also induces a so-called problem of information leakage , which can be overcome by the newly introduced patching technique. Together, these give rise to CASE, which is a two-stage Screen and Clean (Fan and Song, 2010; Wasserman and Roeder, 2009) procedure, where we first identify candidates of these submodels by patching and screening , and then re-examine each candidate to remove false positives. For any procedure β̂ for variable selection, we measure the performance by the minimax Hamming distance between the sign vectors of β̂ and β. We show that in a broad class of situations where the Gram matrix is non-sparse but sparsifiable, CASE achieves the optimal rate of convergence. The results are successfully applied to long-memory time series and the change-point model.

Matrix Information Geometry

CERN Document Server

Bhatia, Rajendra

2013-01-01

This book is an outcome of the Indo-French Workshop on Matrix Information Geometries (MIG): Applications in Sensor and Cognitive Systems Engineering, which was held in Ecole Polytechnique and Thales Research and Technology Center, Palaiseau, France, in February 23-25, 2011. The workshop was generously funded by the Indo-French Centre for the Promotion of Advanced Research (IFCPAR).  During the event, 22 renowned invited french or indian speakers gave lectures on their areas of expertise within the field of matrix analysis or processing. From these talks, a total of 17 original contribution or state-of-the-art chapters have been assembled in this volume. All articles were thoroughly peer-reviewed and improved, according to the suggestions of the international referees. The 17 contributions presented  are organized in three parts: (1) State-of-the-art surveys & original matrix theory work, (2) Advanced matrix theory for radar processing, and (3) Matrix-based signal processing applications.  

Development of 10×10 Matrix-anode MCP-PMT

Science.gov (United States)

Yang, Jie; Li, Yongbin; Xu, Pengxiao; Zhao, Wenjin

2018-02-01

10×10 matrix-anode is developed by high-temperature co-fired ceramics (HTCC) technology. Based on the new matrix-anode, a new kind of photon counting imaging detector - 10×10 matrix-anode MCP-PMT is developed, and its performance parameters are tested. HTCC technology is suitable for the MCP-PMT's air impermeability and its baking process. Its response uniformity is better than the metal-ceramic or metal-glass sealing anode, and it is also a promising method to realize a higher density matrix-anode.

Hand function with touch screen technology in children with normal hand formation, congenital differences, and neuromuscular disease.

Science.gov (United States)

Shin, David H; Bohn, Deborah K; Agel, Julie; Lindstrom, Katy A; Cronquist, Sara M; Van Heest, Ann E

2015-05-01

To measure and compare hand function for children with normal hand development, congenital hand differences (CHD), and neuromuscular disease (NMD) using a function test with touch screen technology designed as an iPhone application. We measured touch screen hand function in 201 children including 113 with normal hand formation, 43 with CHD, and 45 with NMD. The touch screen test was developed on the iOS platform using an Apple iPhone 4. We measured 4 tasks: touching dots on a 3 × 4 grid, dragging shapes, use of the touch screen camera, and typing a line of text. The test takes 60 to 120 seconds and includes a pretest to familiarize the subject with the format. Each task is timed independently and the overall time is recorded. Children with normal hand development took less time to complete all 4 subtests with increasing age. When comparing children with normal hand development with those with CHD or NMD, in children aged less than 5 years we saw minimal differences; those aged 5 to 6 years with CHD took significantly longer total time; those aged 7 to 8 years with NMD took significantly longer total time; those aged 9 to 11 years with CHD took significantly longer total time; and those aged 12 years and older with NMD took significantly longer total time. Touch screen technology has becoming increasingly relevant to hand function in modern society. This study provides standardized age norms and shows that our test discriminates between normal hand development and that in children with CHD or NMD. Diagnostic III. Copyright © 2015 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Developing a Health Information Technology Systems Matrix: A Qualitative Participatory Approach.

Science.gov (United States)

Haun, Jolie N; Chavez, Margeaux; Nazi, Kim M; Antinori, Nicole

2016-10-06

The US Department of Veterans Affairs (VA) has developed various health information technology (HIT) resources to provide accessible veteran-centered health care. Currently, the VA is undergoing a major reorganization of VA HIT to develop a fully integrated system to meet consumer needs. Although extensive system documentation exists for various VA HIT systems, a more centralized and integrated perspective with clear documentation is needed in order to support effective analysis, strategy, planning, and use. Such a tool would enable a novel view of what is currently available and support identifying and effectively capturing the consumer's vision for the future. The objective of this study was to develop the VA HIT Systems Matrix, a novel tool designed to describe the existing VA HIT system and identify consumers' vision for the future of an integrated VA HIT system. This study utilized an expert panel and veteran informant focus groups with self-administered surveys. The study employed participatory research methods to define the current system and understand how stakeholders and veterans envision the future of VA HIT and interface design (eg, look, feel, and function). Directed content analysis was used to analyze focus group data. The HIT Systems Matrix was developed with input from 47 veterans, an informal caregiver, and an expert panel to provide a descriptive inventory of existing and emerging VA HIT in four worksheets: (1) access and function, (2) benefits and barriers, (3) system preferences, and (4) tasks. Within each worksheet is a two-axis inventory. The VA's existing and emerging HIT platforms (eg, My HealtheVet, Mobile Health, VetLink Kiosks, Telehealth), My HealtheVet features (eg, Blue Button, secure messaging, appointment reminders, prescription refill, vet library, spotlight, vitals tracker), and non-VA platforms (eg, phone/mobile phone, texting, non-VA mobile apps, non-VA mobile electronic devices, non-VA websites) are organized by row. Columns

Developing a Health Information Technology Systems Matrix: A Qualitative Participatory Approach

Science.gov (United States)

Chavez, Margeaux; Nazi, Kim M; Antinori, Nicole

2016-01-01

Background The US Department of Veterans Affairs (VA) has developed various health information technology (HIT) resources to provide accessible veteran-centered health care. Currently, the VA is undergoing a major reorganization of VA HIT to develop a fully integrated system to meet consumer needs. Although extensive system documentation exists for various VA HIT systems, a more centralized and integrated perspective with clear documentation is needed in order to support effective analysis, strategy, planning, and use. Such a tool would enable a novel view of what is currently available and support identifying and effectively capturing the consumer’s vision for the future. Objective The objective of this study was to develop the VA HIT Systems Matrix, a novel tool designed to describe the existing VA HIT system and identify consumers’ vision for the future of an integrated VA HIT system. Methods This study utilized an expert panel and veteran informant focus groups with self-administered surveys. The study employed participatory research methods to define the current system and understand how stakeholders and veterans envision the future of VA HIT and interface design (eg, look, feel, and function). Directed content analysis was used to analyze focus group data. Results The HIT Systems Matrix was developed with input from 47 veterans, an informal caregiver, and an expert panel to provide a descriptive inventory of existing and emerging VA HIT in four worksheets: (1) access and function, (2) benefits and barriers, (3) system preferences, and (4) tasks. Within each worksheet is a two-axis inventory. The VA’s existing and emerging HIT platforms (eg, My HealtheVet, Mobile Health, VetLink Kiosks, Telehealth), My HealtheVet features (eg, Blue Button, secure messaging, appointment reminders, prescription refill, vet library, spotlight, vitals tracker), and non-VA platforms (eg, phone/mobile phone, texting, non-VA mobile apps, non-VA mobile electronic devices, non

Understanding the digital divide in the clinical setting: the technology knowledge gap experienced by US safety net patients during teleretinal screening.

Science.gov (United States)

George, Sheba; Moran, Erin; Fish, Allison; Ogunyemi, Lola

2013-01-01

Differential access to everyday technology and healthcare amongst safety net patients is associated with low technological and health literacies, respectively. These low rates of literacy produce a complex patient "knowledge gap" that influences the effectiveness of telehealth technologies. To understand this "knowledge gap", six focus groups (2 African-American and 4 Latino) were conducted with patients who received teleretinal screenings in U.S. urban safety-net settings. Findings indicate that patients' "knowledge gap" is primarily produced at three points: (1) when patients' preexisting personal barriers to care became exacerbated in the clinical setting; (2) through encounters with technology during screening; and (3) in doctor-patient follow-up. This "knowledge gap" can produce confusion and fear, potentially affecting patients' confidence in quality of care and limiting their disease management ability. In rethinking the digital divide to include the consequences of this knowledge gap faced by patients in the clinical setting, we suggest that patient education focus on both their disease and specific telehealth technologies deployed in care delivery.

Les Houches lectures on matrix models and topological strings

CERN Document Server

Marino, M

2004-01-01

In these lecture notes for the Les Houches School on Applications of Random Matrices in Physics we give an introduction to the connections between matrix models and topological strings. We first review some basic results of matrix model technology and then we focus on type B topological strings. We present the main results of Dijkgraaf and Vafa describing the spacetime string dynamics on certain Calabi-Yau backgrounds in terms of matrix models, and we emphasize the connection to geometric transitions and to large N gauge/string duality. We also use matrix model technology to analyze large N Chern-Simons theory and the Gopakumar-Vafa transition.

Feasibility of using touch screen technology for early cognitive assessment in children.

Science.gov (United States)

Twomey, Deirdre M; Wrigley, Conal; Ahearne, Caroline; Murphy, Raegan; De Haan, Michelle; Marlow, Neil; Murray, Deirdre M

2018-03-13

To explore the feasibility of using a touch screen assessment tool to measure cognitive capacity in toddlers. 112 typically developing children with a median age of 31 months (IQR: 26-34) interacted with a touch screen cognitive assessment tool. We examined the sensitivity of the tool to age-related changes in cognition by comparing the number of items completed, speed of task completion and accuracy in two age groups; 24-29 months versus 30-36 months. Children aged 30-36 months completed more tasks (median: 18, IQR: 18-18) than those aged 24-29 months (median: 17, IQR: 15-18). Older children also completed two of the three working memory tasks and an object permanence task faster than their younger peers. Children became faster at completing the working memory items with each exposure and registered similar completion times on the hidden object retrieval items, despite task demands being twofold on the second exposure. A novel item required children to integrate what they had learnt on preceding items. The older group was more likely to complete this item and to do so faster than the younger group. Children as young as 24 months can complete items requiring cognitive engagement on a touch screen device, with no verbal instruction and minimal child-administrator interaction. This paves the way for using touch screen technology for language and administrator independent developmental assessment in toddlers. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Particle-Reinforced Aluminum Matrix Composites (AMCs—Selected Results of an Integrated Technology, User, and Market Analysis and Forecast

Directory of Open Access Journals (Sweden)

Anja Schmidt

2018-02-01

Full Text Available The research and development of new materials such as particle-reinforced aluminum matrix composites (AMCs will only result in a successful innovation if these materials show significant advantages not only from a technological, but also from an economic point of view. Against this background, in the Collaborative Research Center SFB 692, the concept of an integrated technology, user, and market analysis and forecast has been developed as a means for assessing the technological and commercial potential of new materials in early life cycle stages. After briefly describing this concept, it is applied to AMCs and the potential field of manufacturing aircraft components. Results show not only technological advances, but also considerable economic potential—the latter one primarily resulting from the possible weight reduction being enabled by the increased yield strength of the new material.

Rapid screening of mixed edible oils and gutter oils by matrix-assisted laser desorption/ionization mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Ng, Tsz-Tsun; So, Pui-Kin; Zheng, Bo [Food Safety and Technology Research Centre, State Key Laboratory of Chirosciences and Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hung Hom Kowloon, Hong Kong Special Administrative Region (China); Shenzhen Key Laboratory of Food Biological Safety Control and State Key Laboratory of Chinese Medicine and Molecular Pharmacology (Incubation), Shenzhen Research Institute of The Hong Kong Polytechnic University, Shenzhen (China); Yao, Zhong-Ping, E-mail: zhongping.yao@polyu.edu.hk [Food Safety and Technology Research Centre, State Key Laboratory of Chirosciences and Department of Applied Biology and Chemical Technology, The Hong Kong Polytechnic University, Hung Hom Kowloon, Hong Kong Special Administrative Region (China); Shenzhen Key Laboratory of Food Biological Safety Control and State Key Laboratory of Chinese Medicine and Molecular Pharmacology (Incubation), Shenzhen Research Institute of The Hong Kong Polytechnic University, Shenzhen (China)

2015-07-16

Highlights: • Simplified sample preparation method for direct analysis of edible oils by MALDI-MS. • Establishment of a preliminary MALDI-MS spectral database of edible oils. • Rapid screening of mixed edible oils and gutter oils. - Abstract: Authentication of edible oils is a long-term issue in food safety, and becomes particularly important with the emergence and wide spread of gutter oils in recent years. Due to the very high analytical demand and diversity of gutter oils, a high throughput analytical method and a versatile strategy for authentication of mixed edible oils and gutter oils are highly desirable. In this study, an improved matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) method has been developed for direct analysis of edible oils. This method involved on-target sample loading, automatic data acquisition and simple data processing. MALDI-MS spectra with high quality and high reproducibility have been obtained using this method, and a preliminary spectral database of edible oils has been set up. The authenticity of an edible oil sample can be determined by comparing its MALDI-MS spectrum and principal component analysis (PCA) results with those of its labeled oil in the database. This method is simple and the whole process only takes several minutes for analysis of one oil sample. We demonstrated that the method was sensitive to change in oil compositions and can be used for measuring compositions of mixed oils. The capability of the method for determining mislabeling enables it for rapid screening of gutter oils since fraudulent mislabeling is a common feature of gutter oils.

Rapid screening of mixed edible oils and gutter oils by matrix-assisted laser desorption/ionization mass spectrometry

International Nuclear Information System (INIS)

Ng, Tsz-Tsun; So, Pui-Kin; Zheng, Bo; Yao, Zhong-Ping

2015-01-01

Highlights: • Simplified sample preparation method for direct analysis of edible oils by MALDI-MS. • Establishment of a preliminary MALDI-MS spectral database of edible oils. • Rapid screening of mixed edible oils and gutter oils. - Abstract: Authentication of edible oils is a long-term issue in food safety, and becomes particularly important with the emergence and wide spread of gutter oils in recent years. Due to the very high analytical demand and diversity of gutter oils, a high throughput analytical method and a versatile strategy for authentication of mixed edible oils and gutter oils are highly desirable. In this study, an improved matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) method has been developed for direct analysis of edible oils. This method involved on-target sample loading, automatic data acquisition and simple data processing. MALDI-MS spectra with high quality and high reproducibility have been obtained using this method, and a preliminary spectral database of edible oils has been set up. The authenticity of an edible oil sample can be determined by comparing its MALDI-MS spectrum and principal component analysis (PCA) results with those of its labeled oil in the database. This method is simple and the whole process only takes several minutes for analysis of one oil sample. We demonstrated that the method was sensitive to change in oil compositions and can be used for measuring compositions of mixed oils. The capability of the method for determining mislabeling enables it for rapid screening of gutter oils since fraudulent mislabeling is a common feature of gutter oils

X-RAY ACTIVE MATRIX PIXEL SENSORS BASEDON J-FET TECHNOLOGY DEVELOPED FOR THE LINAC COHERENT LIGHT SOURCE.

Energy Technology Data Exchange (ETDEWEB)

CARINI,G.A.; CHEN, W.; LI, Z.; REHAK, P.; SIDDONS, D.P.

2007-10-29

An X-ray Active Matrix Pixel Sensor (XAMPS) is being developed for recording data for the X-ray Pump Probe experiment at the Linac Coherent Light Source (LCLS). Special attention has to be paid to some technological challenges that this design presents. New processes were developed and refined to address problems encountered during previous productions of XAMPS. The development of these critical steps and corresponding tests results are reported here.

Label-free screening of single biomolecules through resistive pulse sensing technology for precision medicine applications

Science.gov (United States)

Harrer, S.; Kim, S. C.; Schieber, C.; Kannam, S.; Gunn, N.; Moore, S.; Scott, D.; Bathgate, R.; Skafidas, S.; Wagner, J. M.

2015-05-01

Employing integrated nano- and microfluidic circuits for detecting and characterizing biological compounds through resistive pulse sensing technology is a vibrant area of research at the interface of biotechnology and nanotechnology. Resistive pulse sensing platforms can be customized to study virtually any particle of choice which can be threaded through a fluidic channel and enable label-free single-particle interrogation with the primary read-out signal being an electric current fingerprint. The ability to perform label-free molecular screening with single-molecule and even single binding site resolution makes resistive pulse sensing technology a powerful tool for analyzing the smallest units of biological systems and how they interact with each other on a molecular level. This task is at the core of experimental systems biology and in particular ‘omics research which in combination with next-generation DNA-sequencing and next-generation drug discovery and design forms the foundation of a novel disruptive medical paradigm commonly referred to as personalized medicine or precision medicine. DNA-sequencing has approached the 1000-Dollar-Genome milestone allowing for decoding a complete human genome with unmatched speed and at low cost. Increased sequencing efficiency yields massive amounts of genomic data. Analyzing this data in combination with medical and biometric health data eventually enables understanding the pathways from individual genes to physiological functions. Access to this information triggers fundamental questions for doctors and patients alike: what are the chances of an outbreak for a specific disease? Can individual risks be managed and if so how? Which drugs are available and how should they be applied? Could a new drug be tailored to an individual’s genetic predisposition fast and in an affordable way? In order to provide answers and real-life value to patients, the rapid evolvement of novel computing approaches for analyzing big data in

Label-free screening of single biomolecules through resistive pulse sensing technology for precision medicine applications.

Science.gov (United States)

Harrer, S; Kim, S C; Schieber, C; Kannam, S; Gunn, N; Moore, S; Scott, D; Bathgate, R; Skafidas, S; Wagner, J M

2015-05-08

Employing integrated nano- and microfluidic circuits for detecting and characterizing biological compounds through resistive pulse sensing technology is a vibrant area of research at the interface of biotechnology and nanotechnology. Resistive pulse sensing platforms can be customized to study virtually any particle of choice which can be threaded through a fluidic channel and enable label-free single-particle interrogation with the primary read-out signal being an electric current fingerprint. The ability to perform label-free molecular screening with single-molecule and even single binding site resolution makes resistive pulse sensing technology a powerful tool for analyzing the smallest units of biological systems and how they interact with each other on a molecular level. This task is at the core of experimental systems biology and in particular 'omics research which in combination with next-generation DNA-sequencing and next-generation drug discovery and design forms the foundation of a novel disruptive medical paradigm commonly referred to as personalized medicine or precision medicine. DNA-sequencing has approached the 1000-Dollar-Genome milestone allowing for decoding a complete human genome with unmatched speed and at low cost. Increased sequencing efficiency yields massive amounts of genomic data. Analyzing this data in combination with medical and biometric health data eventually enables understanding the pathways from individual genes to physiological functions. Access to this information triggers fundamental questions for doctors and patients alike: what are the chances of an outbreak for a specific disease? Can individual risks be managed and if so how? Which drugs are available and how should they be applied? Could a new drug be tailored to an individual's genetic predisposition fast and in an affordable way? In order to provide answers and real-life value to patients, the rapid evolvement of novel computing approaches for analyzing big data in

Ethical Matrix Manual

NARCIS (Netherlands)

Mepham, B.; Kaiser, M.; Thorstensen, E.; Tomkins, S.; Millar, K.

2006-01-01

The ethical matrix is a conceptual tool designed to help decision-makers (as individuals or working in groups) reach sound judgements or decisions about the ethical acceptability and/or optimal regulatory controls for existing or prospective technologies in the field of food and agriculture.

Large-screen display industry: market and technology trends for direct view and projection displays

Science.gov (United States)

Castellano, Joseph A.; Mentley, David E.

1996-03-01

Large screen information displays are defined as dynamic electronic displays that can be viewed by more than one person and are at least 2-feet wide. These large area displays for public viewing provide convenience, entertainment, security, and efficiency to the viewers. There are numerous uses for large screen information displays including those in advertising, transportation, traffic control, conference room presentations, computer aided design, banking, and military command/control. A noticeable characteristic of the large screen display market is the interchangeability of display types. For any given application, the user can usually choose from at least three alternative technologies, and sometimes from many more. Some display types have features that make them suitable for specific applications due to temperature, brightness, power consumption, or other such characteristic. The overall worldwide unit consumption of large screen information displays of all types and for all applications (excluding consumer TV) will increase from 401,109 units in 1995 to 655,797 units in 2002. On a unit consumption basis, applications in business and education represent the largest share of unit consumption over this time period; in 1995, this application represented 69.7% of the total. The market (value of shipments) will grow from DOL3.1 billion in 1995 to DOL3.9 billion in 2002. The market will be dominated by front LCD projectors and LCD overhead projector plates.

Screen-film mammography

International Nuclear Information System (INIS)

Logan, W.W.; Janus, J.A.

1987-01-01

The development of screen-film mammography has resulted in the re-emergence of confidence, rather than fear, in mammography. When screen-film mammography is performed with state-of-the-art dedicated equipment utilizing vigorous breast compression and a ''soft'' x-ray beam for improved contrast, screen-film images are equivalent or superior to those of reduced-dose xeromammography and superior to those of nonscreen film mammography. Technological aids for conversion from xeromammographic or nonscreen film mammographic techniques to screen-film techniques have been described. Screen-film mammography should not be attempted until dedicated equipment has been obtained and the importance of vigorous compression has been understood

UCLA's Molecular Screening Shared Resource: enhancing small molecule discovery with functional genomics and new technology.

Science.gov (United States)

Damoiseaux, Robert

2014-05-01

The Molecular Screening Shared Resource (MSSR) offers a comprehensive range of leading-edge high throughput screening (HTS) services including drug discovery, chemical and functional genomics, and novel methods for nano and environmental toxicology. The MSSR is an open access environment with investigators from UCLA as well as from the entire globe. Industrial clients are equally welcome as are non-profit entities. The MSSR is a fee-for-service entity and does not retain intellectual property. In conjunction with the Center for Environmental Implications of Nanotechnology, the MSSR is unique in its dedicated and ongoing efforts towards high throughput toxicity testing of nanomaterials. In addition, the MSSR engages in technology development eliminating bottlenecks from the HTS workflow and enabling novel assays and readouts currently not available.

National Security Science and Technology Initiative: Air Cargo Screening, Final Report for CRADA Number NFE-07-01081

Energy Technology Data Exchange (ETDEWEB)

Bingham, Philip [ORNL; Bush, John [Battelle Memorial Institute; Bowerman, Biays [Brookhaven National Laboratory; Cespedes, Ernesto [Idaho National Laboratory; White, Timothy [Pacific Northwest National Laboratory

2004-12-01

The non-intrusive inspection (NII) of consolidated air cargo carried on commercial passenger aircraft continues to be a technically challenging, high-priority requirement of the Department of Homeland Security’s Science and Technology Directorate (DHS S&T), the Transportation Security Agency and the Federal Aviation Administration. The goal of deploying a screening system that can reliably and cost-effectively detect explosive threats in consolidated cargo without adversely affecting the flow of commerce will require significant technical advances that will take years to develop. To address this critical National Security need, the Battelle Memorial Institute (Battelle), under a Cooperative Research and Development Agreement (CRADA) with four of its associated US Department of Energy (DOE) National Laboratories (Oak Ridge, Pacific Northwest, Idaho, and Brookhaven), conducted a research and development initiative focused on identifying, evaluating, and integrating technologies for screening consolidated air cargo for the presence of explosive threats. Battelle invested $8.5M of internal research and development funds during fiscal years 2007 through 2009.

Chondrogenic properties of collagen type XI, a component of cartilage extracellular matrix.

Science.gov (United States)

Li, Ang; Wei, Yiyong; Hung, Clark; Vunjak-Novakovic, Gordana

2018-08-01

Cartilage extracellular matrix (ECM) has been used for promoting tissue engineering. However, the exact effects of ECM on chondrogenesis and the acting mechanisms are not well understood. In this study, we investigated the chondrogenic effects of cartilage ECM on human mesenchymal stem cells (MSCs) and identified the contributing molecular components. To this end, a preparation of articular cartilage ECM was supplemented to pellets of chondrogenically differentiating MSCs, pellets of human chondrocytes, and bovine articular cartilage explants to evaluate the effects on cell proliferation and the production of cartilaginous matrix. Selective enzymatic digestion and screening of ECM components were conducted to identify matrix molecules with chondrogenic properties. Cartilage ECM promoted MSC proliferation, production of cartilaginous matrix, and maturity of chondrogenic differentiation, and inhibited the hypertrophic differentiation of MSC-derived chondrocytes. Selective digestion of ECM components revealed a contributory role of collagens in promoting chondrogenesis. The screening of various collagen subtypes revealed strong chondrogenic effect of collagen type XI. Finally, collagen XI was found to promote production and inhibit degradation of cartilage matrix in human articular chondrocyte pellets and bovine articular cartilage explants. Our results indicate that cartilage ECM promotes chondrogenesis and inhibits hypertrophic differentiation in MSCs. Collagen type XI is the ECM component that has the strongest effects on enhancing the production and inhibiting the degradation of cartilage matrix. Copyright © 2018 Elsevier Ltd. All rights reserved.

Gastric adenocarcinoma screening and prevention in the era of new biomarker and endoscopic technologies: a cost-effectiveness analysis.

Science.gov (United States)

Yeh, Jennifer M; Hur, Chin; Ward, Zachary; Schrag, Deborah; Goldie, Sue J

2016-04-01

To estimate the cost-effectiveness of noncardia gastric adenocarcinoma (NCGA) screening strategies based on new biomarker and endoscopic technologies. Using an intestinal-type NCGA microsimulation model, we evaluated the following one-time screening strategies for US men: (1) serum pepsinogen to detect gastric atrophy (with endoscopic follow-up of positive screen results), (2) endoscopic screening to detect dysplasia and asymptomatic cancer (with endoscopic mucosal resection (EMR) treatment for detected lesions) and (3) Helicobacter pylori screening and treatment. Screening performance, treatment effectiveness, cancer and cost data were based on published literature and databases. Subgroups included current, former and never smokers. Outcomes included lifetime cancer risk and incremental cost-effectiveness ratios (ICERs), expressed as cost per quality-adjusted-life-year (QALY) gained. Screening the general population at age 50 years reduced the lifetime intestinal-type NCGA risk (0.24%) by 26.4% with serum pepsinogen screening, 21.2% with endoscopy and EMR and 0.2% with H. pylori screening/treatment. Targeting current smokers reduced the lifetime risk (0.35%) by 30.8%, 25.5%, and 0.1%, respectively. For all subgroups, serum pepsinogen screening was more effective and more cost-effective than all other strategies, although its ICER varied from $76,000/QALY (current smokers) to $105,400/QALY (general population). Results were sensitive to H. pylori prevalence, screen age and serum pepsinogen test sensitivity. Probabilistic sensitivity analysis found that at a $100,000/QALY willingness-to-pay threshold, the probability that serum pepsinogen screening was preferred was 0.97 for current smokers. Although not warranted for the general population, targeting high-risk smokers for serum pepsinogen screening may be a cost-effective strategy to reduce intestinal-type NCGA mortality. Published by the BMJ Publishing Group Limited. For permission to use (where not already

A test matrix sequencer for research test facility automation

Science.gov (United States)

Mccartney, Timothy P.; Emery, Edward F.

1990-01-01

The hardware and software configuration of a Test Matrix Sequencer, a general purpose test matrix profiler that was developed for research test facility automation at the NASA Lewis Research Center, is described. The system provides set points to controllers and contact closures to data systems during the course of a test. The Test Matrix Sequencer consists of a microprocessor controlled system which is operated from a personal computer. The software program, which is the main element of the overall system is interactive and menu driven with pop-up windows and help screens. Analog and digital input/output channels can be controlled from a personal computer using the software program. The Test Matrix Sequencer provides more efficient use of aeronautics test facilities by automating repetitive tasks that were once done manually.

[Technology and prevention in the era of mobile health: applications for cancer screening programs].

Science.gov (United States)

Bert, Fabrizio; Gualano, Maria Rosaria; Clemente, Salvatore; Villa, Giulia; Siliquini, Roberta

2017-01-01

The Italian national health system provides screening to detect breast, colorecatal and cervical cancers, however, population adherence is not as high as expected. Smartphones and their applications (apps) could be used as a tool to communicate with the population and to help improve adherence. The aim of this study was to analyze the features and functions of smartphone applications aimed at secondary prevention of oncological diseases. In February 2016, we reviewed online app stores, using specific key-words, to search for available apps for cancer screening. We identified 32 apps meeting our inclusion criteria. The most frequent types of app are breast cancer (13/32) and cervical cancer (4/32) screening apps. We also found apps addressing secondary prevention of cancers for which screening is not provided to the Italian population (melanoma, prostate cancer and hepatocellular carcinoma). The most common features are: information providers (22/32), risk calculators (10/32), reminders for appointments and tests (7/32). Only one app has been validated for diagnostic accuracy or utility using established international certification (CE Marking). The results show a large potential for development and utilization of applications in secondary prevention. Despite their potential usefulness, there are also disadvantages such as language barriers (only 2 of 32 apps are in Italian), and the digital divide. Future efforts should focus on improving education regarding approaches to technologies, strengthen national and international regulations and monitoring inequalities in access to services.

Impact of technology on cytology outcome in cervical cancer screening of young and older women

DEFF Research Database (Denmark)

Rask, J; Lynge, E; Franzmann, M

2014-01-01

in a third laboratory using manually read conventional cytology continually. Data were collected from the Danish National Health Care Registers. For each laboratory, we compared proportions of abnormal cytology defined as atypical squamous cells of undetermined significance or worse (ASCUS+) by age......Little is known about age-dependent variation in outcomes of cervical cytology with modern technologies. This population-based study evaluated age-dependent changes after routine implementation of ThinPrep and SurePath technology in two independent laboratories, and controlled for time trends...... and technology phase. The study included 489,960 cytological samples with no recent abnormality from women aged 23-59 years, routinely screened between 1998 and 2007. Implementation of SurePath liquid-based cytology (LBC) was followed by an increase in abnormal cytology in women aged 23-29 years from 4.6 to 6...

The SBIRT program matrix: a conceptual framework for program implementation and evaluation.

Science.gov (United States)

Del Boca, Frances K; McRee, Bonnie; Vendetti, Janice; Damon, Donna

2017-02-01

Screening, Brief Intervention and Referral to Treatment (SBIRT) is a comprehensive, integrated, public health approach to the delivery of services to those at risk for the adverse consequences of alcohol and other drug use, and for those with probable substance use disorders. Research on successful SBIRT implementation has lagged behind studies of efficacy and effectiveness. This paper (1) outlines a conceptual framework, the SBIRT Program Matrix, to guide implementation research and program evaluation and (2) specifies potential implementation outcomes. Overview and narrative description of the SBIRT Program Matrix. The SBIRT Program Matrix has five components, each of which includes multiple elements: SBIRT services; performance sites; provider attributes; patient/client populations; and management structure and activities. Implementation outcomes include program adoption, acceptability, appropriateness, feasibility, fidelity, costs, penetration, sustainability, service provision and grant compliance. The Screening, Brief Intervention and Referral to Treatment Program Matrix provides a template for identifying, classifying and organizing the naturally occurring commonalities and variations within and across SBIRT programs, and for investigating which variables are associated with implementation success and, ultimately, with treatment outcomes and other impacts. © 2017 Society for the Study of Addiction.

Quantitative image analysis for investigating cell-matrix interactions

Science.gov (United States)

Burkel, Brian; Notbohm, Jacob

2017-07-01

The extracellular matrix provides both chemical and physical cues that control cellular processes such as migration, division, differentiation, and cancer progression. Cells can mechanically alter the matrix by applying forces that result in matrix displacements, which in turn may localize to form dense bands along which cells may migrate. To quantify the displacements, we use confocal microscopy and fluorescent labeling to acquire high-contrast images of the fibrous material. Using a technique for quantitative image analysis called digital volume correlation, we then compute the matrix displacements. Our experimental technology offers a means to quantify matrix mechanics and cell-matrix interactions. We are now using these experimental tools to modulate mechanical properties of the matrix to study cell contraction and migration.

Smart material screening machines using smart materials and controls

Science.gov (United States)

Allaei, Daryoush; Corradi, Gary; Waigand, Al

2002-07-01

The objective of this product is to address the specific need for improvements in the efficiency and effectiveness in physical separation technologies in the screening areas. Currently, the mining industry uses approximately 33 billion kW-hr per year, costing 1.65 billion dollars at 0.05 cents per kW-hr, of electrical energy for physical separations. Even though screening and size separations are not the single most energy intensive process in the mining industry, they are often the major bottleneck in the whole process. Improvements to this area offer tremendous potential in both energy savings and production improvements. Additionally, the vibrating screens used in the mining processing plants are the most costly areas from maintenance and worker health and safety point of views. The goal of this product is to reduce energy use in the screening and total processing areas. This goal is accomplished by developing an innovative screening machine based on smart materials and smart actuators, namely smart screen that uses advanced sensory system to continuously monitor the screening process and make appropriate adjustments to improve production. The theory behind the development of Smart Screen technology is based on two key technologies, namely smart actuators and smart Energy Flow ControlT (EFCT) strategies, developed initially for military applications. Smart Screen technology controls the flow of vibration energy and confines it to the screen rather than shaking much of the mass that makes up the conventional vibratory screening machine. Consequently, Smart Screens eliminates and downsizes many of the structural components associated with conventional vibratory screening machines. As a result, the surface area of the screen increases for a given envelope. This increase in usable screening surface area extends the life of the screens, reduces required maintenance by reducing the frequency of screen change-outs and improves throughput or productivity.

Comparison of visual field test results obtained through Humphrey matrix frequency doubling technology perimetry versus standard automated perimetry in healthy children.

Science.gov (United States)

Kocabeyoglu, Sibel; Uzun, Salih; Mocan, Mehmet Cem; Bozkurt, Banu; Irkec, Murat; Orhan, Mehmet

2013-10-01

The aim of this study was to compare the visual field test results in healthy children obtained via the Humphrey matrix 24-2 threshold program and standard automated perimetry (SAP) using the Swedish interactive threshold algorithm (SITA)-Standard 24-2 test. This prospective study included 55 healthy children without ocular or systemic disorders who underwent both SAP and frequency doubling technology (FDT) perimetry visual field testing. Visual field test reliability indices, test duration, global indices (mean deviation [MD], and pattern standard deviation [PSD]) were compared between the 2 tests using the Wilcoxon signed-rank test and paired t-test. The performance of the Humphrey field analyzer (HFA) 24-2 SITA-standard and frequency-doubling technology Matrix 24-2 tests between genders were compared with Mann-Whitney U-test. Fifty-five healthy children with a mean age of 12.2 ± 1.9 years (range from 8 years to 16 years) were included in this prospective study. The test durations of SAP and FDT were similar (5.2 ± 0.5 and 5.1 ± 0.2 min, respectively, P = 0.651). MD and the PSD values obtained via FDT Matrix were significantly higher than those obtained via SAP (P tests in terms of MD (r = 0.352, P = 0.008) and PSD (r = 0.329, P = 0.014) was observed. Children were able to complete both the visual test algorithms successfully within 6 min. However, SAP testing appears to be associated with less depression of the visual field indices of healthy children. FDT Matrix and SAP should not be used interchangeably in the follow-up of children.

A Sign Language Screen Reader for Deaf

Science.gov (United States)

El Ghoul, Oussama; Jemni, Mohamed

Screen reader technology has appeared first to allow blind and people with reading difficulties to use computer and to access to the digital information. Until now, this technology is exploited mainly to help blind community. During our work with deaf people, we noticed that a screen reader can facilitate the manipulation of computers and the reading of textual information. In this paper, we propose a novel screen reader dedicated to deaf. The output of the reader is a visual translation of the text to sign language. The screen reader is composed by two essential modules: the first one is designed to capture the activities of users (mouse and keyboard events). For this purpose, we adopted Microsoft MSAA application programming interfaces. The second module, which is in classical screen readers a text to speech engine (TTS), is replaced by a novel text to sign (TTSign) engine. This module converts text into sign language animation based on avatar technology.

Identification of GPR65, a novel regulator of matrix metalloproteinases using high through-put screening

Energy Technology Data Exchange (ETDEWEB)

Xu, Hongbo; Chen, Xiaohong; Huang, Junwei [Department of Otolaryngology-Head and Neck Surgery, Beijing Tongren Hospital, Capital Medical University, Key Laboratory of Otolaryngology Head and Neck Surgery, Beijing (China); Deng, Weiwei [Functional Genomics Group, Chinese National Human Genome Center (CHGB) at Beijing (China); Zhong, Qi [Department of Otolaryngology-Head and Neck Surgery, Beijing Tongren Hospital, Capital Medical University, Key Laboratory of Otolaryngology Head and Neck Surgery, Beijing (China); Yue, Changli [Department of Pathology, Beijing Tongren Hospital, Capital Medical University, Beijing (China); Wang, Pingzhang, E-mail: wangpzh@bjmu.edu.cn [Department of Immunology, School of Basic Medical Sciences, Peking University Health Science Center, Peking University Center for Human Disease Genomics, Key Laboratory of Medical Immunology, Ministry of Health (China); Functional Genomics Group, Chinese National Human Genome Center (CHGB) at Beijing (China); Huang, Zhigang, E-mail: enthuangzhigang@sohu.com [Department of Otolaryngology-Head and Neck Surgery, Beijing Tongren Hospital, Capital Medical University, Key Laboratory of Otolaryngology Head and Neck Surgery, Beijing (China)

2013-06-21

Highlights: •A novel mechanism of MMP3 regulation by proton-sensing G-protein-coupled receptors was defined. •GPR65 was identified to induce the MMP3 expression. •GPR65 mediated MMP induction under acidic conditions. •AP-1 binding site in MMP3 promoter was crucial for MMP3 induction. •GPR65 overexpression can accelerate the invision of A549 cells. -- Abstract: Matrix metalloproteinases (MMPs) are over-expressed in nearly all cancers. To study novel regulatory factors of MMP expression in head and neck cancer (HNC), we screened a total of 636 candidate genes encoding putative human transmembrane proteins using MMP promoter reporter in a dual luciferase assay system. Three genes GPR65, AXL and TNFRSF10B dramatically activated the induction of MMP3 expression. The induction of MMP expression by GPR65 was further confirmed in A549 and/or FaDu cells. GPR65 mediated MMP induction under acidic conditions. The AP-1 binding site in MMP3 promoter was crucial for MMP3 induction. Moreover, the A549 cells infected by recombinant adenovirus of GPR65 showed accelerated cell invasion. In conclusion, we validate that GPR65 is vital regulatory genes upstream of MMP3, and define a novel mechanism of MMP3 regulation by proton-sensing G-protein-coupled receptors.

Identification of GPR65, a novel regulator of matrix metalloproteinases using high through-put screening

International Nuclear Information System (INIS)

Xu, Hongbo; Chen, Xiaohong; Huang, Junwei; Deng, Weiwei; Zhong, Qi; Yue, Changli; Wang, Pingzhang; Huang, Zhigang

2013-01-01

Highlights: •A novel mechanism of MMP3 regulation by proton-sensing G-protein-coupled receptors was defined. •GPR65 was identified to induce the MMP3 expression. •GPR65 mediated MMP induction under acidic conditions. •AP-1 binding site in MMP3 promoter was crucial for MMP3 induction. •GPR65 overexpression can accelerate the invision of A549 cells. -- Abstract: Matrix metalloproteinases (MMPs) are over-expressed in nearly all cancers. To study novel regulatory factors of MMP expression in head and neck cancer (HNC), we screened a total of 636 candidate genes encoding putative human transmembrane proteins using MMP promoter reporter in a dual luciferase assay system. Three genes GPR65, AXL and TNFRSF10B dramatically activated the induction of MMP3 expression. The induction of MMP expression by GPR65 was further confirmed in A549 and/or FaDu cells. GPR65 mediated MMP induction under acidic conditions. The AP-1 binding site in MMP3 promoter was crucial for MMP3 induction. Moreover, the A549 cells infected by recombinant adenovirus of GPR65 showed accelerated cell invasion. In conclusion, we validate that GPR65 is vital regulatory genes upstream of MMP3, and define a novel mechanism of MMP3 regulation by proton-sensing G-protein-coupled receptors

The evolving role of new imaging methods in breast screening.

Science.gov (United States)

Houssami, Nehmat; Ciatto, Stefano

2011-09-01

The potential to avert breast cancer deaths through screening means that efforts continue to identify methods which may enhance early detection. While the role of most new imaging technologies remains in adjunct screening or in the work-up of mammography-detected abnormalities, some of the new breast imaging tests (such as MRI) have roles in screening groups of women defined by increased cancer risk. This paper highlights the evidence and the current role of new breast imaging technologies in screening, focusing on those that have broader application in population screening, including digital mammography, breast ultrasound in women with dense breasts, and computer-aided detection. It highlights that evidence on new imaging in screening comes mostly from non-randomised studies that have quantified test detection capability as adjunct to mammography, or have compared measures of screening performance for new technologies with that of conventional mammography. Two RCTs have provided high-quality evidence on the equivalence of digital and conventional mammography and on outcomes of screen-reading complemented by CAD. Many of these imaging technologies enhance cancer detection but also increase recall and false positives in screening. Copyright © 2011 Elsevier Inc. All rights reserved.

Role of frequency doubling technology perimetry in screening of diabetic retinopathy.

Directory of Open Access Journals (Sweden)

Parikh Rajul

2006-01-01

Full Text Available Purpose: To study the ability of frequency-doubling technology perimetry (FDT to detect sight-threatening diabetic retinopathy. Method: Fifty-eight eyes of fifty-eight patients with established diagnosis of diabetes mellitus with diabetic retinopathy, fifty-five eyes of fifty-five diabetic patients without retinopathy, and forty-one eyes of forty-one normals underwent FDT and dilated stereo-biomicroscopic fundus examination. The sensitivity and specificity of FDT in identification of "sight-threatening retinopathy" (severe and very severe nonproliferative diabetic retinopathy and proliferative diabetic retinopathy and clinically significant macular edema (CSME were determined. Results: For the detection of sight-threatening retinopathy, two abnormal adjacent points depressed to any level on the 20-1 screening program had a sensitivity of 90.5% and specificity of 97.6%. At (assuming a 10% prevalence of sight-threatening retinopathy in a diabetic clinic, two abnormal adjacent points anywhere in the field depressed to any level has a positive predictive value (PPV of 48% with a negative predictive value of 98.8%. Sensitivity and specificity for the detection of CSME was poor. Conclusions: The 20-1 screening program of the FDT is useful in the detection of sight-threatening diabetic retinopathy (PPV 48%. A normal 20-1 test rules out sight-threatening retinopathy. FDT was not useful in the detection of CSME.

Electrochemical screening of biomembrane-active compounds in water

Energy Technology Data Exchange (ETDEWEB)

Mohamadi, Shahrzad, E-mail: cmsm@leeds.ac.uk; Tate, Daniel J.; Vakurov, Alexander; Nelson, Andrew

2014-02-01

Graphical abstract: - Highlights: • Analytical technology application with improvement allowing for on-line high-throughput water toxin screening is presented. • Compound classes of related structure and shape interact with DOPC coated Pt/Hg with a class specific response. • Predecessor membrane system proved as fragile, complex and for environmental application incompatible. - Abstract: Interactions of biomembrane-active compounds with phospholipid monolayers on microfabricated Pt/Hg electrodes in an on-line high throughput flow system are demonstrated by recording capacitance current peak changes as rapid cyclic voltammograms (RCV). Detection limits of the compounds’ effects on the layer have been estimated from the data. Compounds studied include steroids, polycyclic aromatic hydrocarbons, tricyclic antidepressants and tricyclic phenothiazines. The results show that the extent and type of interaction depends on the—(a) presence and number of aromatic rings and substituents, (b) presence and composition of side chains and, (c) molecular shape. Interaction is only indirectly related to compound hydrophobicity. For a selection of tricyclic antidepressants and tricyclic phenothiazines the detection limit in water is related to their therapeutic normal threshold. The sensing assay has been tested in the presence of humic acid as a potential interferent and in a tap water matrix. The system can be applied to the screening of putative hazardous substances and pharmaceuticals allowing for early detection thereof in the water supply. The measurements are made in real time which means that potentially toxic compounds are detected rapidly within <10 min per assay. This technology will contribute greatly to environment safety and health.

Electrochemical screening of biomembrane-active compounds in water

International Nuclear Information System (INIS)

Mohamadi, Shahrzad; Tate, Daniel J.; Vakurov, Alexander; Nelson, Andrew

2014-01-01

Graphical abstract: - Highlights: • Analytical technology application with improvement allowing for on-line high-throughput water toxin screening is presented. • Compound classes of related structure and shape interact with DOPC coated Pt/Hg with a class specific response. • Predecessor membrane system proved as fragile, complex and for environmental application incompatible. - Abstract: Interactions of biomembrane-active compounds with phospholipid monolayers on microfabricated Pt/Hg electrodes in an on-line high throughput flow system are demonstrated by recording capacitance current peak changes as rapid cyclic voltammograms (RCV). Detection limits of the compounds’ effects on the layer have been estimated from the data. Compounds studied include steroids, polycyclic aromatic hydrocarbons, tricyclic antidepressants and tricyclic phenothiazines. The results show that the extent and type of interaction depends on the—(a) presence and number of aromatic rings and substituents, (b) presence and composition of side chains and, (c) molecular shape. Interaction is only indirectly related to compound hydrophobicity. For a selection of tricyclic antidepressants and tricyclic phenothiazines the detection limit in water is related to their therapeutic normal threshold. The sensing assay has been tested in the presence of humic acid as a potential interferent and in a tap water matrix. The system can be applied to the screening of putative hazardous substances and pharmaceuticals allowing for early detection thereof in the water supply. The measurements are made in real time which means that potentially toxic compounds are detected rapidly within <10 min per assay. This technology will contribute greatly to environment safety and health

Preschool Children's Exposure to Media, Technology, and Screen Time: Perspectives of Caregivers from Three Early Childcare Settings

Science.gov (United States)

Sharkins, Kimberly A.; Newton, Allison B.; Albaiz, Najla Essa A.; Ernest, James M.

2016-01-01

Young children are being increasingly exposed to media, technology, and screen time (MeTS) at home and in instructional settings. Little is known about the long-term effects of MeTS and there is a lack of research concerning caregivers' opinions regarding young children's exposure to and utilization of MeTS. Therefore, this study explored the…

Secondary Waste Form Screening Test Results—THOR® Fluidized Bed Steam Reforming Product in a Geopolymer Matrix

Energy Technology Data Exchange (ETDEWEB)

Pires, Richard P.; Westsik, Joseph H.; Serne, R. Jeffrey; Mattigod, Shas V.; Golovich, Elizabeth C.; Valenta, Michelle M.; Parker, Kent E.

2011-07-14

Screening tests are being conducted to evaluate waste forms for immobilizing secondary liquid wastes from the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Plans are underway to add a stabilization treatment unit to the Effluent Treatment Facility to provide the needed capacity for treating these wastes from WTP. The current baseline is to use a Cast Stone cementitious waste form to solidify the wastes. Through a literature survey, DuraLith alkali-aluminosilicate geopolymer, fluidized-bed steam reformation (FBSR) granular product encapsulated in a geopolymer matrix, and a Ceramicrete phosphate-bonded ceramic were identified both as candidate waste forms and alternatives to the baseline. These waste forms have been shown to meet waste disposal acceptance criteria, including compressive strength and universal treatment standards for Resource Conservation and Recovery Act (RCRA) metals (as measured by the toxicity characteristic leaching procedure [TCLP]). Thus, these non-cementitious waste forms should also be acceptable for land disposal. Information is needed on all four waste forms with respect to their capability to minimize the release of technetium. Technetium is a radionuclide predicted to be in the secondary liquid wastes in small quantities, but the Integrated Disposal Facility (IDF) risk assessment analyses show that technetium, even at low mass, produces the largest contribution to the estimated IDF disposal impacts to groundwater.

Challenging the CSCW matrix

DEFF Research Database (Denmark)

Jørnø, Rasmus Leth Vergmann; Gynther, Karsten; Christensen, Ove

2014-01-01

useful information, we question whether the axis of time and space comprising the matrix pertains to relevant defining properties of the tools, technology or learning environments to which they are applied. Subsequently we offer an example of an Adobe Connect e-learning session as an illustration...

Autostereoscopic image creation by hyperview matrix controlled single pixel rendering

Science.gov (United States)

Grasnick, Armin

2017-06-01

Just as the increasing awareness level of the stereoscopic cinema, so the perception of limitations while watching movies with 3D glasses has been emerged as well. It is not only that the additional glasses are uncomfortable and annoying; there are some tangible arguments for avoiding 3D glasses. These "stereoscopic deficits" are caused by the 3D glasses itself. In contrast to natural viewing with naked eyes, the artificial 3D viewing with 3D glasses introduces specific "unnatural" side effects. The most of the moviegoers has experienced unspecific discomfort in 3D cinema, which they may have associated with insufficient image quality. Obviously, quality problems with 3D glasses can be solved by technical improvement. But this simple answer can -and already has- mislead some decision makers to relax on the existing 3D glasses solution. It needs to be underlined, that there are inherent difficulties with the glasses, which can never be solved with modest advancement; as the 3D glasses initiate them. To overcome the limitations of stereoscopy in display applications, several technologies has been proposed to create a 3D impression without the need of 3D glasses, known as autostereoscopy. But even todays autostereoscopic displays cannot solve all viewing problems and still show limitations. A hyperview display could be a suitable candidate, if it would be possible to create an affordable device and generate the necessary content in an acceptable time frame. All autostereoscopic displays, based on the idea of lightfield, integral photography or super-multiview could be unified within the concept of hyperview. It is essential for functionality that every of these display technologies uses numerous of different perspective images to create the 3D impression. Such a calculation of a very high number of views will require much more computing time as for the formation of a simple stereoscopic image pair. The hyperview concept allows to describe the screen image of any 3D

Preparation of mixed matrix adsorber membranes for protein recovery

NARCIS (Netherlands)

Avramescu, M.E.; Girones nogue, Miriam; Borneman, Zandrie; Wessling, Matthias

2003-01-01

This paper presents a generic technology allowing the incorporation of functional entities into a porous substrate. Various ion exchange particles were incorporated into an ethylene vinyl alcohol (EVAL) copolymer porous matrix by an immersion phase separation process and a heterogeneous matrix,

Science-Economy-Technology Concordance Matrix for Development and Implementation of Regional Smart Specializations in the Silesian Voivodeship, Poland

Directory of Open Access Journals (Sweden)

Adam Smoliński

2015-01-01

Full Text Available The regional smart specializations include the innovative activities within a common science-economy-technology sector, which open the opportunities to gain a competitive advantage. The original procedure of science-economy-technology concordance matrix development on an example of smart specializations of the Silesian Voivodeship was presented in the paper. The procedure developed includes recognition of the research and economic components of the regional smart specialization and the connection between the economic components of the regional specialization and the technological innovation through the international patent classification. It also comprises recognition of key enabling technologies (KETs and high technologies (of high R&D intensity other than KET in the economic and technological dimensions of innovation as well as the high R&D intensity services in the economic dimension of innovation. The in-depth expert analyses with the application of the Delphi method were also taken into account. The methodological approach developed and the visualization method applied are both of cognitive and practical importance since they contribute significantly to the creation of efficient development policies, to the enhancement and facilitation of cross-sectoral cooperation, and to the focusing on the fields of key importance in terms of the competitive advantage of a region.

Science-Economy-Technology Concordance Matrix for Development and Implementation of Regional Smart Specializations in the Silesian Voivodeship, Poland.

Science.gov (United States)

Smoliński, Adam; Bondaruk, Jan; Pichlak, Magdalena; Trząski, Leszek; Uszok, Elżbieta

2015-01-01

The regional smart specializations include the innovative activities within a common science-economy-technology sector, which open the opportunities to gain a competitive advantage. The original procedure of science-economy-technology concordance matrix development on an example of smart specializations of the Silesian Voivodeship was presented in the paper. The procedure developed includes recognition of the research and economic components of the regional smart specialization and the connection between the economic components of the regional specialization and the technological innovation through the international patent classification. It also comprises recognition of key enabling technologies (KETs) and high technologies (of high R&D intensity) other than KET in the economic and technological dimensions of innovation as well as the high R&D intensity services in the economic dimension of innovation. The in-depth expert analyses with the application of the Delphi method were also taken into account. The methodological approach developed and the visualization method applied are both of cognitive and practical importance since they contribute significantly to the creation of efficient development policies, to the enhancement and facilitation of cross-sectoral cooperation, and to the focusing on the fields of key importance in terms of the competitive advantage of a region.

Improvement of characteristics of diffraction gratings in Dot-matrix holograms

International Nuclear Information System (INIS)

ZHUMALIEV, K.M.; ISMAILOV, D.A.; ZHEENBEKOV, A.A.; SARYBAEVA, A.A.; KAZAKBAEVA, Z.M.

2014-01-01

This paper describes the results of research of the formation and recording of matrix hologram by Dot-matrix (dot-matrix hologram) technology on the photosensitive material of the photoresist. The principle of creating and modifying the characteristics of diffraction gratings of each pixel based on the diffraction efficiency, and recovery of colors and dynamic visual effects in dot-matrix holograms are discussed. An optical schematic diagram of the device and the process of recording dot-matrix holograms are presented. (authors)

Trialling computer touch-screen technology to assess psychological distress in patients with gynaecological cancer

Directory of Open Access Journals (Sweden)

Georgia Halkett

2010-12-01

Full Text Available BackgroundCancer impacts on the psychological well-being of many cancer patients. Appropriate tools can be used to assist health professionals in identifying patient needs and psychological distress. Recent research suggests that touchscreen technology can be used to administer surveys. The aim of this study was to evaluate the use of a touchscreen system in comparison to written questionnaires in a large tertiary hospital in Western Australia (WA.Method Patients who were scheduled to commence treatment for gynaecological cancer participated in this study. Patients were assigned to complete either a written questionnaire or the same survey using the touchscreen technology. Both methods of survey contained the same scales. All participants were asked to complete a follow-up patient satisfaction survey. Semi-structured interviews were conducted with health professionals to elicit views about the implementation of the technology and the available referral pathways. Data was analysed using descriptive statistics and content analysis. ResultsThirty patients completed the touchscreen questionnaires and an equal number completed the survey on paper. Participants who used the touchscreens were not significantly more satisfied than other participants. Four themes were noted in the interviews with health professionals: usability of technology, patients’ acceptance of technology, advantages of psychological screening and the value of the instruments included.ConclusionAlthough previous studies report that computerised assessments are a feasible option for assessing cancer patients’ needs, the data collected in this study demonstrates that the technology was not reliable with significant practical problems. The technology did not serve these patients better than pen and paper.

Comparison of visual field test results obtained through Humphrey matrix frequency doubling technology perimetry versus standard automated perimetry in healthy children

Directory of Open Access Journals (Sweden)

Sibel Kocabeyoglu

2013-01-01

Full Text Available Aims : The aim of this study was to compare the visual field test results in healthy children obtained via the Humphrey matrix 24-2 threshold program and standard automated perimetry (SAP using the Swedish interactive threshold algorithm (SITA-Standard 24-2 test. Materials and Methods: This prospective study included 55 healthy children without ocular or systemic disorders who underwent both SAP and frequency doubling technology (FDT perimetry visual field testing. Visual field test reliability indices, test duration, global indices (mean deviation [MD], and pattern standard deviation [PSD] were compared between the 2 tests using the Wilcoxon signed-rank test and paired t-test. The performance of the Humphrey field analyzer (HFA 24-2 SITA-standard and frequency-doubling technology Matrix 24-2 tests between genders were compared with Mann-Whitney U-test. Results: Fifty-five healthy children with a mean age of 12.2 ± 1.9 years (range from 8 years to 16 years were included in this prospective study. The test durations of SAP and FDT were similar (5.2 ± 0.5 and 5.1 ± 0.2 min, respectively, P = 0.651. MD and the PSD values obtained via FDT Matrix were significantly higher than those obtained via SAP (P < 0.001, and fixation losses and false negative errors were significantly less with SAP (P < 0.05. A weak positive correlation between the two tests in terms of MD (r = 0.352, P = 0.008 and PSD (r = 0.329, P = 0.014 was observed. Conclusion: Children were able to complete both the visual test algorithms successfully within 6 min. However, SAP testing appears to be associated with less depression of the visual field indices of healthy children. FDT Matrix and SAP should not be used interchangeably in the follow-up of children.

Comparative proteomics of matrix fractions between pimpled and normal chicken eggshells.

Science.gov (United States)

Liu, Zhangguo; Song, Lingzi; Lu, Lizhi; Zhang, Xianfu; Zhang, Fuming; Wang, Kehua; Linhardt, Robert J

2017-09-07

Eggshell matrix can be dissociated into three matrix fractions: acid-insoluble matrix (M1), water-insoluble matrix (M2) and acid-water facultative-soluble matrix (M3). Matrix fractions from pimpled and normal eggshells were compared using label-free proteomic method to understand the differences among three matrix fractions and the proteins involved with eggshell quality. A total of 738 and 600 proteins were identified in the pimpled and normal calcified eggshells, respectively. Both eggshells showed a combined proteomic inventory of 769 proteins. In the same type of eggshell, a high similarity was present in the proteomes of three matrix fractions. These triply overlapped common proteins formed the predominant contributor to proteomic abundance in the matrix fractions. In each matrix fraction and between both eggshell models, normal and pimpled eggshells, a majority of the proteomes of the fractions were commonly observed. Forty-two common major proteins (iBAQ-derived abundance ≥0.095% of proteomic abundance) were identified throughout the three matrix fractions and these proteins might act as backbone constituents in chicken eggshell matrix. Finally, using 1.75-fold as up-regulated and using 0.57-fold as down-regulated cutoff values, twenty-five differential major proteins were screened and they all negatively influence and none showed any effect on eggshell quality. Overall, we uncovered the characteristics of proteomics of three eggshell matrix fractions and identified candidate proteins influencing eggshell quality. The next research on differential proteins will uncover the potential mechanisms underlying how proteins affect eggshell quality. It was reported that the proteins in an eggshell can be divided into insoluble and soluble proteins. The insoluble proteins are thought to be an inter-mineral matrix and acts as a structural framework, while the soluble proteins are thought as intra-mineral matrix that are embedded within the crystal during

Designing airport checked-baggage-screening strategies considering system capability and reliability

International Nuclear Information System (INIS)

Feng Qianmei; Sahin, Hande; Kapur, Kailash C.

2009-01-01

Emerging image-based technologies are critical components of airport security for screening checked baggage. Since these new technologies differ widely in cost and accuracy, a comprehensive mathematical framework should be developed for selecting technology or combination of technologies for efficient 100% baggage screening. This paper addresses the problem of setting threshold values of these screening technologies and determining the optimal combination of technologies in a two-level screening system by considering system capability and human reliability. Probability and optimization techniques are used to quantify and evaluate the cost- and risk-effectiveness of various deployment configurations, which is captured by using a system life-cycle cost model that incorporates the deployment cost, operating cost, and costs associated with system decisions. Two system decision rules are studied for a two-level screening system. For each decision rule, two different optimization approaches are formulated and investigated from practitioner's perspective. Numerical examples for different decision rules, optimization approaches and system arrangements are demonstrated

Participant recruitment and motivation for participation in optical technology for cervical cancer screening research trials.

Science.gov (United States)

Shuhatovich, Olga M; Sharman, Mathilde P; Mirabal, Yvette N; Earle, Nan R; Follen, Michele; Basen-Engquist, Karen

2005-12-01

In order to improve recruitment for cervical cancer screening trials, it is necessary to analyze the effectiveness of recruitment strategies used in current trials. A trial to test optical spectroscopy for the diagnosis of cervical neoplasia recruited 1000 women from the community; the trial evaluated the emerging technology against Pap smears and colposcopically directed biopsies for cervical dysplasia. We have examined women's reasons for participating as well as the effectiveness and efficiency for each recruitment strategy. Reasons for participation were identified and compared between trials. The recruitment method that resulted in the most contacts was newspaper reportorial coverage and advertising, followed by family and friends, then television news coverage. The most cost-effective method for finding eligible women who attend the research appointment is word of mouth from a family member or friend. Recommendations are given for maximizing the efficiency of recruitment for cervical cancer screening trials.

New generation expandable sand screens

OpenAIRE

Syltøy, Christer

2014-01-01

Master's thesis in Petroleum engineering This thesis aims to give a general insight into sand control and various sorts of sand control measures and applications of sand control tools. Special focus will be given to expandable sand screens – a technology which came about in the late 1990’s through the use of flexible, expandable tubulars as base pipe in sand screens. More specifically Darcy’s Hydraulic Endurance Screens, a compliant sand screen system using hydraulic activation, and the fu...

Study of extraterrestrial disposal of radioactive wastes. Part 2: Preliminary feasibility screening study of extraterrestrial disposal of radioactive wastes in concentrations, matrix materials, and containers designed for storage on earth

Science.gov (United States)

Hyland, R. E.; Wohl, M. L.; Thompson, R. L.; Finnegan, P. M.

1972-01-01

The results are reported of a preliminary feasibility screening study for providing long-term solutions to the problems of handling and managing radioactive wastes by extraterrestrial transportation of the wastes. Matrix materials and containers are discussed along with payloads, costs, and destinations for candidate space vehicles. The conclusions reached are: (1) Matrix material such as spray melt can be used without exceeding temperature limits of the matrix. (2) The cost in mills per kw hr electric, of space disposal of fission products is 4, 5, and 28 mills per kw hr for earth escape, solar orbit, and solar escape, respectively. (3) A major factor effecting cost is the earth storage time. Based on a normal operating condition design for solar escape, a storage time of more than sixty years is required to make the space disposal charge less than 10% of the bus-bar electric cost. (4) Based on a 10 year earth storage without further processing, the number of shuttle launches required would exceed one per day.

Ethical, legal, and social issues in health technology assessment for prenatal/preconceptional and newborn screening: a workshop report.

Science.gov (United States)

Potter, B K; Avard, D; Entwistle, V; Kennedy, C; Chakraborty, P; McGuire, M; Wilson, B J

2009-01-01

Prenatal/preconceptional and newborn screening programs have been a focus of recent policy debates that have included attention to ethical, legal, and social issues (ELSIs). In parallel, there has been an ongoing discussion about whether and how ELSIs may be addressed in health technology assessment (HTA). We conducted a knowledge synthesis study to explore both guidance and current practice regarding the consideration of ELSIs in HTA for prenatal/preconceptional and newborn screening. As the concluding activity for this project, we held a Canadian workshop to discuss the issues with a diverse group of stakeholders. Based on key workshop themes integrated with our study results, we suggest that population-based genetic screening programs may present particular types of ELSIs and that a public health ethics perspective is potentially highly relevant when considering them. We also suggest that approaches to addressing ELSIs in HTA for prenatal/preconceptional and newborn screening may need to be flexible enough to respond to diversity in HTA organizations, cultural values, stakeholder communities, and contextual factors. Finally, we highlight a need for transparency in the way that HTA producers move from evidence to conclusions and the ways in which screening policy decisions are made. Copyright © 2008 S. Karger AG, Basel.

ScreenBEAM: a novel meta-analysis algorithm for functional genomics screens via Bayesian hierarchical modeling.

Science.gov (United States)

Yu, Jiyang; Silva, Jose; Califano, Andrea

2016-01-15

Functional genomics (FG) screens, using RNAi or CRISPR technology, have become a standard tool for systematic, genome-wide loss-of-function studies for therapeutic target discovery. As in many large-scale assays, however, off-target effects, variable reagents' potency and experimental noise must be accounted for appropriately control for false positives. Indeed, rigorous statistical analysis of high-throughput FG screening data remains challenging, particularly when integrative analyses are used to combine multiple sh/sgRNAs targeting the same gene in the library. We use large RNAi and CRISPR repositories that are publicly available to evaluate a novel meta-analysis approach for FG screens via Bayesian hierarchical modeling, Screening Bayesian Evaluation and Analysis Method (ScreenBEAM). Results from our analysis show that the proposed strategy, which seamlessly combines all available data, robustly outperforms classical algorithms developed for microarray data sets as well as recent approaches designed for next generation sequencing technologies. Remarkably, the ScreenBEAM algorithm works well even when the quality of FG screens is relatively low, which accounts for about 80-95% of the public datasets. R package and source code are available at: https://github.com/jyyu/ScreenBEAM. ac2248@columbia.edu, jose.silva@mssm.edu, yujiyang@gmail.com Supplementary data are available at Bioinformatics online. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Screening and classification of ceramic powders

Science.gov (United States)

Miwa, S.

1983-01-01

A summary is given of the classification technology of ceramic powders. Advantages and disadvantages of the wet and dry screening and classification methods are discussed. Improvements of wind force screening devices are described.

TECHNOLOGY AND ANALYSIS DEVELOPMENT OF STOMATOLOGICAL MATRIX SYSTEM OF MULTIFUNCTIONAL ACTION DELIVERY

Directory of Open Access Journals (Sweden)

T. F. Marinina

2014-01-01

Full Text Available Timeliness of double-layer matrix system (of stomatological medicated films with antiinflammatory, local anesthetic, regenerative, anti-edematous action was shown. One layer of the system includes lidocaine hydrochloride and kalanchoe sap, another contains furacilin and urea. The best possible polymer carriers of preparations under study which provide their sufficient release from matrix system. Signified antimicrobic activity of double-layer system and osmotic activity were established. Double-layer matrix systems offered may be used in stomatology with for treatment and preventive measures of different diseases of parodontium tissues

A generic approach for expanding homolog-targeted residue screening of sulfonamides using a fast matrix separation and class-specific fragmentation-dependent acquisition with a hybrid quadrupole-linear ion trap mass spectrometer

Energy Technology Data Exchange (ETDEWEB)

Huang Chunlin [Department of Biochemistry and Molecular Biology, School of Pharmacy and Life Science, University of South China, Hengyang 421001 (China); Guo Bin, E-mail: binnguo@126.com [Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research (Ministry of Education of China), Hunan Normal University, Changsha 410081 (China); Wang Xiaoying [Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research (Ministry of Education of China), Hunan Normal University, Changsha 410081 (China); Li Jie [Department of Biochemistry and Molecular Biology, School of Pharmacy and Life Science, University of South China, Hengyang 421001 (China); Zhu Weitao; Chen Bo [Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research (Ministry of Education of China), Hunan Normal University, Changsha 410081 (China); Ouyang Shan [Food Inspection and Quarantine Center, Shenzhen Entry-Exit Inspection and Quarantine Bureau of the People' s Republic of China, Shenzhen 518067 (China); Yao Shouzhuo [Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research (Ministry of Education of China), Hunan Normal University, Changsha 410081 (China)

2012-08-06

Highlights: Black-Right-Pointing-Pointer Generic homolog-targeted screening approach for multi-residual sulfonamide analogs. Black-Right-Pointing-Pointer Single-tube extraction/partitioning-multifunction adsorption cleanup for direct injection. Black-Right-Pointing-Pointer Class-specific fragmentation for expanding coverage of N{sup 4}-acetyl and N-OH metabolites. Black-Right-Pointing-Pointer PreS-IDA-EPI in LC-QqLIT for simultaneous screening and confirmation of real samples. - Abstract: A generic and efficient homolog-targeted approach was used to expand screening and detection of target class of sulfonamides and structural analogs, based on a fast single-tube extraction/partitioning-multifunction adsorption cleanup (SEP/MAC) for class-specific fragmentation-dependent acquisition with a liquid chromatography-hybrid triple-quadrupole linear ion trap mass spectrometer (LC-QqLIT). By combining the two-stage process conducted in a single tube as one-pot protocol, the straightforward SEP/MAC procedure was optimized to offer clean extracts with reasonable recovery (71-109% with RSDs < 20%) and decreased matrix interferences (-9 to 19%) of multiresidual sulfonamide extraction from different tissue samples. The novel use of neutral loss scan of 66 Da (NLS) or precursor ion scanning of m/z 108 (PreS) in positive ion mode was found to achieve more comprehensive coverage of protonated molecular ions of a wide array of sulfonamides including N{sup 4}-acetyl and hydroxylamine metabolites plus their possible dimers. Moreover, the PreS-triggered automatically enhanced product ion spectral acquisition enabled simultaneous screening, profiling and confirmation of an unlimited number of analytes belonging to the sulfonamide class within a single analysis. The validation and application results of the generic SEP/MAC-based LC-QqLIT strategy consistently demonstrated favorable performances with acceptable accuracy (67-116%), precision (RSDs < 25%), and sensitivity (LOQs {<=} 7.5 ng

Silver Matrix Composites - Structure and Properties

Directory of Open Access Journals (Sweden)

Wieczorek J.

2016-03-01

Full Text Available Phase compositions of composite materials determine their performance as well as physical and mechanical properties. Depending on the type of applied matrix and the kind, amount and morphology of the matrix reinforcement, it is possible to shape the material properties so that they meet specific operational requirements. In the paper, results of investigations on silver alloy matrix composites reinforced with ceramic particles are presented. The investigations enabled evaluation of hardness, tribological and mechanical properties as well as the structure of produced materials. The matrix of composite material was an alloy of silver and aluminium, magnesium and silicon. As the reinforcing phase, 20-60 μm ceramic particles (SiC, SiO2, Al2O3 and Cs were applied. The volume fraction of the reinforcing phase in the composites was 10%. The composites were produced using the liquid phase (casting technology, followed by plastic work (the KOBO method. The mechanical and tribological properties were analysed for plastic work-subjected composites. The mechanical properties were assessed based on a static tensile and hardness tests. The tribological properties were investigated under dry sliding conditions. The analysis of results led to determination of effects of the composite production technology on their performance. Moreover, a relationship between the type of reinforcing phase and the mechanical and tribological properties was established.

Nucleic acid amplification technology screening for hepatitis C virus and human immunodeficiency virus for blood donations

International Nuclear Information System (INIS)

Bamaga, Mohammad S.; Bokhari, Fawzi F.; Aboud, Abdulrehman M.; Al-Malki, M.; Alenzi, Faris Q.

2006-01-01

To investigate the performance of the commercial Roche COBAS AmpliScreen assay, and demonstrate whether the COBAS AmpliScreen human immunodeficiency virus-1 (HIV-1) test, v1.5, and COBAS AmpliScreen hepatitis C virus (HCV) v 2.0 for screening for HIV-1 and HCV RNA in the donated blood units from which plasma mini pools were collected, by nucleic acid amplification technology (NAT), could detect the positive pools and reduce the risk of transmission of infections for those routinely tested by serological assays. The study was performed on 3288 plasma samples collected from blood donors in a period of 13 months, from August 2004 to August 2005, at Al-Hada Armed Forces Hospital, Molecular Pathology Laboratory, Taif, Kingdom of Saudi Arabia. The samples were tested by the reverse transcriptase polymerase chain reaction (RT-PCR) after RNA extraction (this represents the major method in NAT assays), in parallel with the routine serological testing to detect qualitatively for HIV-1 and HCV. The NAT assays that include an automated COBAS AmpliPrep system for RNA extraction and COBAS Amplicor Analyzer using AmpliScreen kits for RT-PCR assays, and the routine serological screening assays for the detection of the HIV-1 and HCV RNA in the plasma samples from the blood donors have shown to be a reliable combination that would meet our requirements. The collected data further confirms the results from the serological assays and enables us to decrease the residual risk of transmission to a minimum with the finding of no seronegative window period donation. The results demonstrate that out of 3288 samples, the percentages of RT-PCR (NAT) negative blood donations that were also confirmed as seronegative were 99% for HCV, and 99.1% for HIV-1. The modified combined systems (automated COBAS AmpliPrep system for RNA extraction and COBAS Amplicor Analyzer using AmpliScreen kits for RT-PCR assays) for NAT screening assays has allowed the release of all blood donations supplied in the

Technologies for pre-screening IAEA swipe samples

International Nuclear Information System (INIS)

Smith, Nicholas A.; Steeb, Jennifer L.; Lee, Denise L.; Huckabay, Heath A.; Ticknor, Brian W.

2015-01-01

During the course of International Atomic Energy Agency (IAEA) inspections, many samples are taken for the purpose of verifying the declared facility activities and identifying any possible undeclared activities. One of these sampling techniques is the environmental swipe sample. Due to the large number of samples collected, and the amount of time that is required to analyze them, prioritizing these swipes in the field or upon receipt at the Network of Analytical Laboratories (NWAL) will allow sensitive or mission-critical analyses to be performed sooner. As a result of this study, technologies were placed into one of three categories: recommended, promising, or not recommended. Both neutron activation analysis (NAA) and X-ray fluorescence (XRF) are recommended for further study and possible field deployment. These techniques performed the best in initial trials for pre-screening and prioritizing IAEA swipes. We learned that for NAA more characterization of cold elements (such as calcium and magnesium) would need to be emphasized, and for XRF it may be appropriate to move towards a benchtop XRF versus a handheld XRF due to the increased range of elements available on benchtop equipment. Promising techniques that will require additional research and development include confocal Raman microscopy, fluorescence microscopy, and infrared (IR) microscopy. These techniques showed substantive responses to uranium compounds, but expensive instrumentation upgrades (confocal Raman) or university engagement (fluorescence microscopy) may be necessary to investigate the utility of the techniques completely. Point-and-shoot (handheld) Raman and attenuated total reflectance–infrared (ATR-IR) measurements are not recommended, as they have not shown enough promise to continue investigations.

Technologies for pre-screening IAEA swipe samples

Energy Technology Data Exchange (ETDEWEB)

Smith, Nicholas A. [Argonne National Lab. (ANL), Argonne, IL (United States); Steeb, Jennifer L. [Argonne National Lab. (ANL), Argonne, IL (United States); Lee, Denise L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Huckabay, Heath A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ticknor, Brian W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-11-09

During the course of International Atomic Energy Agency (IAEA) inspections, many samples are taken for the purpose of verifying the declared facility activities and identifying any possible undeclared activities. One of these sampling techniques is the environmental swipe sample. Due to the large number of samples collected, and the amount of time that is required to analyze them, prioritizing these swipes in the field or upon receipt at the Network of Analytical Laboratories (NWAL) will allow sensitive or mission-critical analyses to be performed sooner. As a result of this study, technologies were placed into one of three categories: recommended, promising, or not recommended. Both neutron activation analysis (NAA) and X-ray fluorescence (XRF) are recommended for further study and possible field deployment. These techniques performed the best in initial trials for pre-screening and prioritizing IAEA swipes. We learned that for NAA more characterization of cold elements (such as calcium and magnesium) would need to be emphasized, and for XRF it may be appropriate to move towards a benchtop XRF versus a handheld XRF due to the increased range of elements available on benchtop equipment. Promising techniques that will require additional research and development include confocal Raman microscopy, fluorescence microscopy, and infrared (IR) microscopy. These techniques showed substantive responses to uranium compounds, but expensive instrumentation upgrades (confocal Raman) or university engagement (fluorescence microscopy) may be necessary to investigate the utility of the techniques completely. Point-and-shoot (handheld) Raman and attenuated total reflectance–infrared (ATR-IR) measurements are not recommended, as they have not shown enough promise to continue investigations.

Refractive index inversion based on Mueller matrix method

Science.gov (United States)

Fan, Huaxi; Wu, Wenyuan; Huang, Yanhua; Li, Zhaozhao

2016-03-01

Based on Stokes vector and Jones vector, the correlation between Mueller matrix elements and refractive index was studied with the result simplified, and through Mueller matrix way, the expression of refractive index inversion was deduced. The Mueller matrix elements, under different incident angle, are simulated through the expression of specular reflection so as to analyze the influence of the angle of incidence and refractive index on it, which is verified through the measure of the Mueller matrix elements of polished metal surface. Research shows that, under the condition of specular reflection, the result of Mueller matrix inversion is consistent with the experiment and can be used as an index of refraction of inversion method, and it provides a new way for target detection and recognition technology.

Efficiency criterion for teleportation via channel matrix, measurement matrix and collapsed matrix

Directory of Open Access Journals (Sweden)

Xin-Wei Zha

Full Text Available In this paper, three kinds of coefficient matrixes (channel matrix, measurement matrix, collapsed matrix associated with the pure state for teleportation are presented, the general relation among channel matrix, measurement matrix and collapsed matrix is obtained. In addition, a criterion for judging whether a state can be teleported successfully is given, depending on the relation between the number of parameter of an unknown state and the rank of the collapsed matrix. Keywords: Channel matrix, Measurement matrix, Collapsed matrix, Teleportation

Marked Object Recognition Multitouch Screen Printed Touchpad for Interactive Applications.

Science.gov (United States)

Nunes, Jivago Serrado; Castro, Nelson; Gonçalves, Sergio; Pereira, Nélson; Correia, Vitor; Lanceros-Mendez, Senentxu

2017-12-01

The market for interactive platforms is rapidly growing, and touchscreens have been incorporated in an increasing number of devices. Thus, the area of smart objects and devices is strongly increasing by adding interactive touch and multimedia content, leading to new uses and capabilities. In this work, a flexible screen printed sensor matrix is fabricated based on silver ink in a polyethylene terephthalate (PET) substrate. Diamond shaped capacitive electrodes coupled with conventional capacitive reading electronics enables fabrication of a highly functional capacitive touchpad, and also allows for the identification of marked objects. For the latter, the capacitive signatures are identified by intersecting points and distances between them. Thus, this work demonstrates the applicability of a low cost method using royalty-free geometries and technologies for the development of flexible multitouch touchpads for the implementation of interactive and object recognition applications.

Marked Object Recognition Multitouch Screen Printed Touchpad for Interactive Applications

Directory of Open Access Journals (Sweden)

Jivago Serrado Nunes

2017-12-01

Full Text Available The market for interactive platforms is rapidly growing, and touchscreens have been incorporated in an increasing number of devices. Thus, the area of smart objects and devices is strongly increasing by adding interactive touch and multimedia content, leading to new uses and capabilities. In this work, a flexible screen printed sensor matrix is fabricated based on silver ink in a polyethylene terephthalate (PET substrate. Diamond shaped capacitive electrodes coupled with conventional capacitive reading electronics enables fabrication of a highly functional capacitive touchpad, and also allows for the identification of marked objects. For the latter, the capacitive signatures are identified by intersecting points and distances between them. Thus, this work demonstrates the applicability of a low cost method using royalty-free geometries and technologies for the development of flexible multitouch touchpads for the implementation of interactive and object recognition applications.

The Impact of Goal Setting and Empowerment on Governmental Matrix Organizations

Science.gov (United States)

1993-09-01

shared. In a study of matrix management, Eduardo Vasconcellos further describes various matrix structures in the Galbraith model. In a functional...Technology/LAR, Wright-Patterson AFB OH, 1992. Vasconcellos , Eduardo . "A Model For a Better Understanding of the Matrix Structure," IEEE Transactions on...project matrix, the project manager maintains more influence and the structure lies to the right-of center ( Vasconcellos , 1979:58). Different Types of

[Screening differentially expressed plasma proteins in cold stress rats based on iTRAQ combined with mass spectrometry technology].

Science.gov (United States)

Liu, Yan-zhi; Guo, Jing-ru; Peng, Meng-ling; Ma, Li; Zhen, Li; Ji, Hong; Yang, Huan-min

2015-09-01

Isobaric tags for relative and absolute quantitation (iTRAQ) combined with mass spectrometry were used to screen differentially expressed plasma proteins in cold stress rats. Thirty health SPF Wistar rats were randomly divided into cold stress group A and control group B, then A and B were randomly divided into 3 groups (n = 5): A1, A2, A3 and B1, B2, B3. The temperature of room raising was (24.0 +/- 0.1) degrees C, and the cold stress temperature was (4.0 +/- 0.1) degrees C. The rats were treated with different temperatures until 12 h. The abdominal aortic blood was collected with heparin anticoagulation suction tube. Then, the plasma was separated for protein extraction, quantitative, enzymolysis, iTHAQ labeling, scx fractionation and mass spectrometry analysis. Totally, 1085 proteins were identified in the test, 39 differentially expressed proteins were screened, including 29 up-regulated proteins and 10 down-regulated proteins. Three important differentially expressed proteins related to cold stress were screened by bioinfonnatics analysis (Minor histocompatihility protein HA-1, Has-related protein Rap-1b, Integrin beta-1). In the experiment, the differentially expressed plasma proteins were successfully screened in cold stress rats. iTRAQ technology provided a good platform to screen protein diaguostic markers on cold stress rats, and laid a good foundation for further. study on animal cold stress mechanism.

High-throughput matrix screening identifies synergistic and antagonistic antimalarial drug combinations

Science.gov (United States)

Mott, Bryan T.; Eastman, Richard T.; Guha, Rajarshi; Sherlach, Katy S.; Siriwardana, Amila; Shinn, Paul; McKnight, Crystal; Michael, Sam; Lacerda-Queiroz, Norinne; Patel, Paresma R.; Khine, Pwint; Sun, Hongmao; Kasbekar, Monica; Aghdam, Nima; Fontaine, Shaun D.; Liu, Dongbo; Mierzwa, Tim; Mathews-Griner, Lesley A.; Ferrer, Marc; Renslo, Adam R.; Inglese, James; Yuan, Jing; Roepe, Paul D.; Su, Xin-zhuan; Thomas, Craig J.

2015-01-01

Drug resistance in Plasmodium parasites is a constant threat. Novel therapeutics, especially new drug combinations, must be identified at a faster rate. In response to the urgent need for new antimalarial drug combinations we screened a large collection of approved and investigational drugs, tested 13,910 drug pairs, and identified many promising antimalarial drug combinations. The activity of known antimalarial drug regimens was confirmed and a myriad of new classes of positively interacting drug pairings were discovered. Network and clustering analyses reinforced established mechanistic relationships for known drug combinations and identified several novel mechanistic hypotheses. From eleven screens comprising >4,600 combinations per parasite strain (including duplicates) we further investigated interactions between approved antimalarials, calcium homeostasis modulators, and inhibitors of phosphatidylinositide 3-kinases (PI3K) and the mammalian target of rapamycin (mTOR). These studies highlight important targets and pathways and provide promising leads for clinically actionable antimalarial therapy. PMID:26403635

Modulation and control of matrix converter for aerospace application

Science.gov (United States)

Kobravi, Keyhan

Converter technology for ac to ac power conversion regarding the existing technologies of Matrix Converters.

Comparison of Matrix Frequency-Doubling Technology (FDT) Perimetry with the SWEDISH Interactive Thresholding Algorithm (SITA) Standard Automated Perimetry (SAP) in Mild Glaucoma.

Science.gov (United States)

Doozandeh, Azadeh; Irandoost, Farnoosh; Mirzajani, Ali; Yazdani, Shahin; Pakravan, Mohammad; Esfandiari, Hamed

2017-01-01

This study aimed to compare second-generation frequency-doubling technology (FDT) perimetry with standard automated perimetry (SAP) in mild glaucoma. Forty-seven eyes of 47 participants who had mild visual field defect by SAP were included in this study. All participants were examined using SITA 24-2 (SITA-SAP) and matrix 24-2 (Matrix-FDT). The correlations of global indices and the number of defects on pattern deviation (PD) plots were determined. Agreement between two sets regarding the stage of visual field damage was assessed. Pearson's correlation, intra-cluster comparison, paired t-test, and 95% limit of agreement were calculated. Although there was no significant difference between global indices, the agreement between the two devices regarding the global indices was weak (the limit of agreement for mean deviation was -6.08 to 6.08 and that for pattern standard deviation was -4.42 to 3.42). The agreement between SITA-SAP and Matrix-FDT regarding the Glaucoma Hemifield Test (GHT) and the number of defective points in each quadrant and staging of the visual field damage was also weak. Because the correlation between SITA-SAP and Matrix-FDT regarding global indices, GHT, number of defective points, and stage of the visual field damage in mild glaucoma is weak, Matrix-FDT cannot be used interchangeably with SITA-SAP in the early stages of glaucoma.

JTEC panel on display technologies in Japan

Science.gov (United States)

Tannas, Lawrence E., Jr.; Glenn, William E.; Credelle, Thomas; Doane, J. William; Firester, Arthur H.; Thompson, Malcolm

1992-01-01

This report is one in a series of reports that describes research and development efforts in Japan in the area of display technologies. The following are included in this report: flat panel displays (technical findings, liquid crystal display development and production, large flat panel displays (FPD's), electroluminescent displays and plasma panels, infrastructure in Japan's FPD industry, market and projected sales, and new a-Si active matrix liquid crystal display (AMLCD) factory); materials for flat panel displays (liquid crystal materials, and light-emissive display materials); manufacturing and infrastructure of active matrix liquid crystal displays (manufacturing logistics and equipment); passive matrix liquid crystal displays (LCD basics, twisted nematics LCD's, supertwisted nematic LCD's, ferroelectric LCD's, and a comparison of passive matrix LCD technology); active matrix technology (basic active matrix technology, investment environment, amorphous silicon, polysilicon, and commercial products and prototypes); and projection displays (comparison of Japanese and U.S. display research, and technical evaluation of work).

High Porosity Alumina as Matrix Material for Composites of Al-Mg Alloys

International Nuclear Information System (INIS)

Gömze, L A; Egész, Á; Gömze, L N; Ojima, F

2013-01-01

The sophisticated industry and technologies require higher and higher assumptions against mechanical strength and surface hardness of ceramic reinforced metal alloys and metal matrix composites. Applying the well-known alumina powders by dry pressing technology and some special pore-forming additives and sintering technology the authors have successfully developed a new, high porosity alumina matrix material for composites of advenced Al-Mg alloys. The developed new matrix material have higher than 30% porosity, with homogenous porous structure and pore sizes from few nano up to 2–3 mm depending on the alloys containments. Thanks to the used materials and the sintering conditions the authors could decrease the wetting angles less than 90° between the high porosity alumina matrix and the Al-Mg alloys. Applied analytical methods in this research were laser granulometry, scanning electron microscopy, and X-ray diffraction. Digital image analysis was applied to microscopy results, to enhance the results of transformation

OD Matrix Acquisition Based on Mobile Phone Positioning Data

Directory of Open Access Journals (Sweden)

Xiaoqing ZUO

2014-06-01

Full Text Available Dynamic OD matrix is basic data of traffic travel guidance, traffic control, traffic management and traffic planning, and reflects the basic needs of travelers on the traffic network. With the rising popularity of positioning technology and the communication technology and the generation of huge mobile phone users, the mining and use of mobile phone positioning data, can get more traffic intersections and import and export data. These data will be integrated into obtaining the regional OD matrix, which is bound to bring convenience. In this article, mobile phone positioning data used in the data acquisition of intelligent transportation system, research a kind of regional dynamic OD matrix acquisition method based on the mobile phone positioning data. The method based on purpose of transportation, using time series similarity classification algorithm based on piecewise linear representation of the corner point (CP-PLR, mapping each base station cell to traffic zone of different traffic characteristics, and through a series of mapping optimization of base station cell to traffic zone to realize city traffic zone division based on mobile phone traffic data, on the basis, adjacency matrix chosen as the physical data structure of OD matrix storage, the principle of obtaining regional dynamic OD matrix based on the mobile phone positioning data are expounded, and the algorithm of obtaining regional dynamic OD matrix based on mobile phone positioning data are designed and verified.

Instant screening and verification of carbapenemase activity in Bacteroides fragilis in positive blood culture, using matrix-assisted laser desorption ionization--time of flight mass spectrometry.

Science.gov (United States)

Johansson, Åsa; Nagy, Elisabeth; Sóki, József

2014-08-01

Rapid identification of isolates in positive blood cultures are of great importance to secure correct treatment of septicaemic patients. As antimicrobial resistance is increasing, rapid detection of resistance is crucial. Carbapenem resistance in Bacteroides fragilis associated with cfiA-encoded class B metallo-beta-lactamase is emerging. In our study we spiked blood culture bottles with 26 B. fragilis strains with various cfiA-status and ertapenem MICs. By using main spectra specific for cfiA-positive and cfiA-negative B. fragilis strains, isolates could be screened for resistance. To verify strains that were positive in the screening, a carbapenemase assay was performed where the specific peaks of intact and hydrolysed ertapenem were analysed with matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS). We show here that it is possible to correctly identify B. fragilis and to screen for enzymic carbapenem resistance directly from the pellet of positive blood cultures. The carbapenemase assay to verify the presence of the enzyme was successfully performed on the pellet from the direct identification despite the presence of blood components. The result of the procedure was achieved in 3 h. Also the Bruker mass spectrometric β-lactamase assay (MSBL assay) prototype software was proven not only to be based on an algorithm that correlated with the manual inspection of the spectra, but also to improve the interpretation by showing the variation in the dataset. © 2014 The Authors.

Detection matrix of an electromagnetic radiation and radiological image intensifier comprising such a matrix

International Nuclear Information System (INIS)

Fraleux, Jean.

1982-01-01

This invention concerns a detection matrix comprising, in an electrode lattice of lines and columns, addressing means constituted of thin film technology MOS transistors and photoconductances which enable the number of unit module crossings to be halved and to bring about an increase in the effective detection area. This detection matrix is employed in radiological image intensifiers where it ensures the conversion of incident X photons into reading electric signals or only the detection of a visible radiation in the case where the incident X photons are converted into lesser energy photons by a scintillator. The scintillator is then formed of a panel brought into contact with the detector mosaic [fr

Advanced ceramic matrix composite materials for current and future propulsion technology applications

Science.gov (United States)

Schmidt, S.; Beyer, S.; Knabe, H.; Immich, H.; Meistring, R.; Gessler, A.

2004-08-01

Current rocket engines, due to their method of construction, the materials used and the extreme loads to which they are subjected, feature a limited number of load cycles. Various technology programmes in Europe are concerned, besides developing reliable and rugged, low cost, throwaway equipment, with preparing for future reusable propulsion technologies. One of the key roles for realizing reusable engine components is the use of modern and innovative materials. One of the key technologies which concern various engine manufacturers worldwide is the development of fibre-reinforced ceramics—ceramic matrix composites. The advantages for the developers are obvious—the low specific weight, the high specific strength over a large temperature range, and their great damage tolerance compared to monolithic ceramics make this material class extremely interesting as a construction material. Over the past years, the Astrium company (formerly DASA) has, together with various partners, worked intensively on developing components for hypersonic engines and liquid rocket propulsion systems. In the year 2000, various hot-firing tests with subscale (scale 1:5) and full-scale nozzle extensions were conducted. In this year, a further decisive milestone was achieved in the sector of small thrusters, and long-term tests served to demonstrate the extraordinary stability of the C/SiC material. Besides developing and testing radiation-cooled nozzle components and small-thruster combustion chambers, Astrium worked on the preliminary development of actively cooled structures for future reusable propulsion systems. In order to get one step nearer to this objective, the development of a new fibre composite was commenced within the framework of a regionally sponsored programme. The objective here is to create multidirectional (3D) textile structures combined with a cost-effective infiltration process. Besides material and process development, the project also encompasses the development of

Application of pristine and doped SnO2 nanoparticles as a matrix for agro-hazardous material (organophosphate) detection

Science.gov (United States)

Khan, Naushad; Athar, Taimur; Fouad, H.; Umar, Ahmad; Ansari, Z. A.; Ansari, S. G.

2017-02-01

With an increasing focus on applied research, series of single/composite materials are being investigated for device development to detect several hazardous, dangerous, and toxic molecules. Here, we report a preliminary attempt of an electrochemical sensor fabricated using pristine Ni and Cr-doped nano tin oxide material (SnO2) as a tool to detect agro-hazardous material, i.e. Organophosphate (OP, chlorpyrifos). The nanomaterial was synthesized using the solution method. Nickel and chromium were used as dopant during synthesis. The synthesized material was calcined at 1000 °C and characterized for morphological, structural, and elemental analysis that showed the formation of agglomerated nanosized particles of crystalline nature. Screen-printed films of powder obtained were used as a matrix for working electrodes in a cyclic voltammogram (CV) at various concentrations of organophosphates (0.01 to 100 ppm). The CV curves were obtained before and after the immobilization of acetylcholinesterase (AChE) on the nanomaterial matrix. An interference study was also conducted with hydroquinone to ascertain the selectivity. The preliminary study indicated that such material can be used as suitable matrix for a device that can easily detect OP to a level of 10 ppb and thus contributes to progress in terms of desired device technology for the food and agricultural-industries.

Small animal SPECT and its place in the matrix of molecular imaging technologies

International Nuclear Information System (INIS)

Meikle, Steven R; Kench, Peter; Kassiou, Michael; Banati, Richard B

2005-01-01

Molecular imaging refers to the use of non-invasive imaging techniques to detect signals that originate from molecules, often in the form of an injected tracer, and observe their interaction with a specific cellular target in vivo. Differences in the underlying physical principles of these measurement techniques determine the sensitivity, specificity and length of possible observation of the signal, characteristics that have to be traded off according to the biological question under study. Here, we describe the specific characteristics of single photon emission computed tomography (SPECT) relative to other molecular imaging technologies. SPECT is based on the tracer principle and external radiation detection. It is capable of measuring the biodistribution of minute ( -10 molar) concentrations of radio-labelled biomolecules in vivo with sub-millimetre resolution and quantifying the molecular kinetic processes in which they participate. Like some other imaging techniques, SPECT was originally developed for human use and was subsequently adapted for imaging small laboratory animals at high spatial resolution for basic and translational research. Its unique capabilities include (i) the ability to image endogenous ligands such as peptides and antibodies due to the relative ease of labelling these molecules with technetium or iodine (ii) the ability to measure relatively slow kinetic processes (compared with positron emission tomography, for example) due to the long half-life of the commonly used isotopes and (iii) the ability to probe two or more molecular pathways simultaneously by detecting isotopes with different emission energies. In this paper, we review the technology developments and design tradeoffs that led to the current state-of-the-art in SPECT small animal scanning and describe the position SPECT occupies within the matrix of molecular imaging technologies. (topical review)

Physics in Screening Environments

Science.gov (United States)

Certik, Ondrej

In the current study, we investigated atoms in screening environments like plasmas. It is common practice to extract physical data, such as temperature and electron densities, from plasma experiments. We present results that address inherent computational difficulties that arise when the screening approach is extended to include the interaction between the atomic electrons. We show that there may arise an ambiguity in the interpretation of physical properties, such as temperature and charge density, from experimental data due to the opposing effects of electron-nucleus screening and electron-electron screening. The focus of the work, however, is on the resolution of inherent computational challenges that appear in the computation of two-particle matrix elements. Those enter already at the Hartree-Fock level. Furthermore, as examples of post Hartree-Fock calculations, we show second-order Green's function results and many body perturbation theory results of second order. A self-contained derivation of all necessary equations has been included. The accuracy of the implementation of the method is established by comparing standard unscreened results for various atoms and molecules against literature for Hartree-Fock as well as Green's function and many body perturbation theory. The main results of the thesis are presented in the chapter called Screened Results, where the behavior of several atomic systems depending on electron-electron and electron-nucleus Debye screening was studied. The computer code that we have developed has been made available for anybody to use. Finally, we present and discuss results obtained for screened interactions. We also examine thoroughly the computational details of the calculations and particular implementations of the method.

High content screening in microfluidic devices

Science.gov (United States)

Cheong, Raymond; Paliwal, Saurabh; Levchenko, Andre

2011-01-01

Importance of the field Miniaturization is key to advancing the state-of-the-art in high content screening (HCS), in order to enable dramatic cost savings through reduced usage of expensive biochemical reagents and to enable large-scale screening on primary cells. Microfluidic technology offers the potential to enable HCS to be performed with an unprecedented degree of miniaturization. Areas covered in this review This perspective highlights a real-world example from the authors’ work of HCS assays implemented in a highly miniaturized microfluidic format. Advantages of this technology are discussed, including cost savings, high throughput screening on primary cells, improved accuracy, the ability to study complex time-varying stimuli, and ease of automation, integration, and scaling. What the reader will gain The reader will understand the capabilities of a new microfluidics-based platform for HCS, and the advantages it provides over conventional plate-based HCS. Take home message Microfluidics technology will drive significant advancements and broader usage and applicability of HCS in drug discovery. PMID:21852997

Optical characterization of display screens by speckle patterns

Science.gov (United States)

Pozo, Antonio M.; Castro, José J.; Rubiño, Manuel

2013-10-01

In recent years, flat-panel display (FPD) technology has undergone great development, and now FPDs appear in many devices. A significant element in FPD manufacturing is the display front surface. Manufacturers sell FPDs with different types of front surfaces, which can be matte (also called anti-glare) or glossy screens. Users who prefer glossy screens consider these displays to show more vivid colors compared with matte-screen displays. However, on the glossy screens, external light sources may cause unpleasant reflections that can be reduced by a matte treatment in the front surface. In this work, we present a method to characterize FPD screens using laser-speckle patterns. We characterize three FPDs: a Samsung XL2370 LCD monitor of 23 in. with matte screen, a Toshiba Satellite A100 LCD laptop of 15.4 in. with glossy screen, and a Grammata Papyre 6.1 electronic book reader of 6 in. with ePaper screen (E-ink technology). The results show great differences in speckle-contrast values for the three screens characterized and, therefore, this work shows the feasibility of this method for characterizing and comparing FPDs that have different types of front surfaces.

Enhancing the quality and efficiency of newborn screening programs through the use of health information technology.

Science.gov (United States)

Downing, Gregory J; Zuckerman, Alan E; Coon, Constanze; Lloyd-Puryear, Michele A

2010-04-01

A variety of efforts are underway at national, state, regional, and local levels to enhance the performance of programs for early detection of inherited diseases and conditions of newborn infants. Newborn screening programs serve a vital purpose in identifying nonsymptomatic clinical conditions and enabling early intervention strategies that lessen morbidity and mortality. Currently, the programs of most intense focus are early hearing detection and intervention, using physiological techniques for audiology screening and use of newborn dried blood spots for detection of metabolites or proteins representing inherited disorders. One of the primary challenges to effective newborn screening programs to date has been the inability to provide information in a timely and easily accessible way to a variety of users. Other challenging communication issues being faced include the complexity introduced by the diversity of conditions for which testing is conducted and laboratory methods being used by each state's screening programs, lack of an electronic information infrastructure to facilitate information exchange, and variation in policies that enable access to information while protecting patient privacy and confidentiality. In this study, we address steps being taken to understand these challenges, outline progress made to date to overcome them, and provide examples of how electronic health information exchange will enhance the utility of newborn screening. It is likely that future advances in science and technology will bring many more opportunities to prevent and preempt disabilities among children through early detection programs. To take their advantage, effective communication strategies are needed among the public health, primary care practice, referral/specialty service, and consumer advocacy communities to provide continuity of information required for medical decision-making throughout prenatal, newborn, and early childhood periods of patient care. Published by

78 FR 76860 - Contraband Screening for Criminal Justice Applications

Science.gov (United States)

2013-12-19

... for the detection of contraband. Screening technology is widely used by criminal justice practitioners...: 1. Model Number and Name of the screening system/device. 2. Technology used by the system/device for... container or bag), Plastic, Wood, Ceramic, Powder (in a small packet), and/or Paper (e.g., folded currency...

Technical Update: Preimplantation Genetic Diagnosis and Screening.

Science.gov (United States)

Dahdouh, Elias M; Balayla, Jacques; Audibert, François; Wilson, R Douglas; Audibert, François; Brock, Jo-Ann; Campagnolo, Carla; Carroll, June; Chong, Karen; Gagnon, Alain; Johnson, Jo-Ann; MacDonald, William; Okun, Nanette; Pastuck, Melanie; Vallée-Pouliot, Karine

2015-05-01

To update and review the techniques and indications of preimplantation genetic diagnosis (PGD) and preimplantation genetic screening (PGS). Discussion about the genetic and technical aspects of preimplantation reproductive techniques, particularly those using new cytogenetic technologies and embryo-stage biopsy. Clinical outcomes of reproductive techniques following the use of PGD and PGS are included. This update does not discuss in detail the adverse outcomes that have been recorded in association with assisted reproductive technologies. Published literature was retrieved through searches of The Cochrane Library and Medline in April 2014 using appropriate controlled vocabulary (aneuploidy, blastocyst/physiology, genetic diseases, preimplantation diagnosis/methods, fertilization in vitro) and key words (e.g., preimplantation genetic diagnosis, preimplantation genetic screening, comprehensive chromosome screening, aCGH, SNP microarray, qPCR, and embryo selection). Results were restricted to systematic reviews, randomized controlled trials/controlled clinical trials, and observational studies published from 1990 to April 2014. There were no language restrictions. Searches were updated on a regular basis and incorporated in the update to January 2015. Additional publications were identified from the bibliographies of retrieved articles. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care. (Table 1) BENEFITS, HARMS, AND COSTS: This update will educate readers about new preimplantation genetic concepts, directions, and technologies. The major harms and costs identified are those of assisted reproductive

Carrier screening in the era of expanding genetic technology.

Science.gov (United States)

Arjunan, Aishwarya; Litwack, Karen; Collins, Nick; Charrow, Joel

2016-12-01

The Center for Jewish Genetics provides genetic education and carrier screening to individuals of Jewish descent. Carrier screening has traditionally been performed by targeted mutation analysis for founder mutations with an enzyme assay for Tay-Sachs carrier detection. The development of next-generation sequencing (NGS) allows for higher detection rates regardless of ethnicity. Here, we explore differences in carrier detection rates between genotyping and NGS in a primarily Jewish population. Peripheral blood samples or saliva samples were obtained from 506 individuals. All samples were analyzed by sequencing, targeted genotyping, triplet-repeat detection, and copy-number analysis; the analyses were carried out at Counsyl. Of 506 individuals screened, 288 were identified as carriers of at least 1 condition and 8 couples were carriers for the same disorder. A total of 434 pathogenic variants were identified. Three hundred twelve variants would have been detected via genotyping alone. Although no additional mutations were detected by NGS in diseases routinely screened for in the Ashkenazi Jewish population, 26.5% of carrier results and 2 carrier couples would have been missed without NGS in the larger panel. In a primarily Jewish population, NGS reveals a larger number of pathogenic variants and provides individuals with valuable information for family planning.Genet Med 18 12, 1214-1217.

Optical properties of flexible fluorescent films prepared by screen printing technology

Directory of Open Access Journals (Sweden)

Yan Chen

2018-05-01

Full Text Available In this work, we prepared a fluorescent film comprised phosphors and silicone on flexible polyethylene terephthalate (PET substrate using a screen printing technology. The effects of mesh number and weight ratio of phosphors to silicone on the optical properties of the flexible films were investigated. The results indicate that the emission intensity of the film increase as the mesh decreased from 400 to 200, but the film surface gradually becomes uneven. The fluorescent film with high emission intensity and smooth surface can be obtained when the weight ratio of phosphor to gel is 2:1, and mesh number is 300. The luminous efficiency of the fabricated LEDs combined the fluorescent films with 460 nm Ga(InN chip module can reach 75 lm/W. The investigation indicates that the approach can be applied in the remote fluorescent film conversion and decreases the requirements of the particle size and the dispersion state of fluorescent materials.

Optical properties of flexible fluorescent films prepared by screen printing technology

Science.gov (United States)

Chen, Yan; Ke, Taiyan; Chen, Shuijin; He, Xin; Zhang, Mei; Li, Dong; Deng, Jinfeng; Zeng, Qingguang

2018-05-01

In this work, we prepared a fluorescent film comprised phosphors and silicone on flexible polyethylene terephthalate (PET) substrate using a screen printing technology. The effects of mesh number and weight ratio of phosphors to silicone on the optical properties of the flexible films were investigated. The results indicate that the emission intensity of the film increase as the mesh decreased from 400 to 200, but the film surface gradually becomes uneven. The fluorescent film with high emission intensity and smooth surface can be obtained when the weight ratio of phosphor to gel is 2:1, and mesh number is 300. The luminous efficiency of the fabricated LEDs combined the fluorescent films with 460 nm Ga(In)N chip module can reach 75 lm/W. The investigation indicates that the approach can be applied in the remote fluorescent film conversion and decreases the requirements of the particle size and the dispersion state of fluorescent materials.

SCREENING FOR EARLY DETECTION OF BREAST CANCER

Directory of Open Access Journals (Sweden)

E. A. Rasskazova

2014-01-01

Full Text Available The article presents a brief overview of the main methods of breast cancer screening. Proven effectiveness of mammography as a screening method in reducing mortality from breast cancer, specified limits of the method. The main trend of increasing the effectiveness of screening is the transition to digital technologies. Properly organized screening with the active participation of the population reduces mortality from breast cancer by 30%.

Preimplantation genetic screening.

Science.gov (United States)

Harper, Joyce C

2018-03-01

Preimplantation genetic diagnosis was first successfully performed in 1989 as an alternative to prenatal diagnosis for couples at risk of transmitting a genetic or chromosomal abnormality, such as cystic fibrosis, to their child. From embryos generated in vitro, biopsied cells are genetically tested. From the mid-1990s, this technology has been employed as an embryo selection tool for patients undergoing in vitro fertilisation, screening as many chromosomes as possible, in the hope that selecting chromosomally normal embryos will lead to higher implantation and decreased miscarriage rates. This procedure, preimplantation genetic screening, was initially performed using fluorescent in situ hybridisation, but 11 randomised controlled trials of screening using this technique showed no improvement in in vitro fertilisation delivery rates. Progress in genetic testing has led to the introduction of array comparative genomic hybridisation, quantitative polymerase chain reaction, and next generation sequencing for preimplantation genetic screening, and three small randomised controlled trials of preimplantation genetic screening using these new techniques indicate a modest benefit. Other trials are still in progress but, regardless of their results, preimplantation genetic screening is now being offered globally. In the near future, it is likely that sequencing will be used to screen the full genetic code of the embryo.

Metal Matrix Microencapsulated Fuel Technology for LWR Applications

International Nuclear Information System (INIS)

Terrani, Kurt A.; Bell, Gary L.; Kiggans, Jim; Snead, Lance Lewis

2012-01-01

An overview of the metal matrix microencapsulated (M3) fuel concept for the specific LWR application has been provided. Basic fuel properties and characteristics that aim to improve operational reliability, enlarge performance envelope, and enhance safety margins under design-basis accident scenarios are summarized. Fabrication of M3 rodlets with various coated fuel particles over a temperature range of 800-1300 C is discussed. Results from preliminary irradiation testing of LWR M3 rodlets with surrogate coated fuel particles are also reported.

Menopausal women requesting egg/embryo donation: examining health screening guidelines for assisted reproductive technology.

Science.gov (United States)

MacArthur, Taleen; Bachmann, Gloria; Ayers, Charletta

2016-07-01

As more postreproductive women opt to pursue pregnancy with advanced assisted reproductive technologies (ART), the menopausal practitioner will become more involved in counseling, screening, and referral of premenopausal, perimenopausal, and postmenopausal women for these services. This review was conducted with the aim of (1) evaluating ART screening practices as they pertain to postreproductive women, and (2) reviewing the outcomes of ART using oocyte donation in postreproductive women. A total of 950 unique records were found on PubMed, Clinical Key, and Google Scholar. Of these, 252 records were screened for relevance based on their titles and abstracts. With further review of these 252 records, 93 full-text articles were assessed for eligibility, and 63 were excluded based on relevance to our study. Finally, 30 studies were included in our qualitative synthesis. Despite the increasing use of ART in postreproductive women, there are limited guidelines for determining candidacy with regard to maternal health, the most comprehensive of which are the guidelines from the American Society for Reproductive Medicine (ASRM). Although the American Society for Reproductive Medicine guidelines state that healthy women over 50 who are prepared for parenthood are candidates for ART through oocyte donation, they note that older women should be counseled as to the increased obstetric risk associated with advanced maternal age. With aging, particularly for those women who are menopausal and postmenopausal, the woman and her fetus, however, are at risk of increased morbidity and mortality as compared with younger, healthy pregnant women. Because national trends suggest that women are delaying childbearing, the cohort of postreproductive women looking toward ART using donor oocytes as a fertility option will expand and menopausal practitioners will often participate in the ART counseling of these women. Because maternal and fetal morbidity and mortality increase in

Extracellular matrix and tissue engineering applications

NARCIS (Netherlands)

Fernandes, H.A.M.; Moroni, Lorenzo; van Blitterswijk, Clemens; de Boer, Jan

2009-01-01

The extracellular matrix is a key component during regeneration and maintenance of tissues and organs, and it therefore plays a critical role in successful tissue engineering as well. Tissue engineers should recognise that engineering technology can be deduced from natural repair processes. Due to

Defining the "proven technology" technical criterion in the reactor technology assessment for Malaysia's nuclear power program

Science.gov (United States)

Anuar, Nuraslinda; Kahar, Wan Shakirah Wan Abdul; Manan, Jamal Abdul Nasir Abd

2015-04-01

Developing countries that are considering the deployment of nuclear power plants (NPPs) in the near future need to perform reactor technology assessment (RTA) in order to select the most suitable reactor design. The International Atomic Energy Agency (IAEA) reported in the Common User Considerations (CUC) document that "proven technology" is one of the most important technical criteria for newcomer countries in performing the RTA. The qualitative description of five desired features for "proven technology" is relatively broad and only provides a general guideline to its characterization. This paper proposes a methodology to define the "proven technology" term according to a specific country's requirements using a three-stage evaluation process. The first evaluation stage screens the available technologies in the market against a predefined minimum Technology Readiness Level (TRL) derived as a condition based on national needs and policy objectives. The result is a list of technology options, which are then assessed in the second evaluation stage against quantitative definitions of CUC desired features for proven technology. The potential technology candidates produced from this evaluation is further narrowed down to obtain a list of proven technology candidates by assessing them against selected risk criteria and the established maximum allowable total score using a scoring matrix. The outcome of this methodology is the proven technology candidates selected using an accurate definition of "proven technology" that fulfills the policy objectives, national needs and risk, and country-specific CUC desired features of the country that performs this assessment. A simplified assessment for Malaysia is carried out to demonstrate and suggest the use of the proposed methodology. In this exercise, ABWR, AP1000, APR1400 and EPR designs assumed the top-ranks of proven technology candidates according to Malaysia's definition of "proven technology".

Strategy BMT Al-Ittihad Using Matrix IE, Matrix SWOT 8K, Matrix SPACE and Matrix TWOS

Directory of Open Access Journals (Sweden)

Nofrizal Nofrizal

2018-03-01

Full Text Available This research aims to formulate and select BMT Al-Ittihad Rumbai strategy to face the changing of business environment both from internal environment such as organization resources, finance, member and external business such as competitor, economy, politics and others. This research method used Analysis of EFAS, IFAS, IE Matrix, SWOT-8K Matrix, SPACE Matrix and TWOS Matrix. our hope from this research it can assist BMT Al-Ittihad in formulating and selecting strategies for the sustainability of BMT Al-Ittihad in the future. The sample in this research is using purposive sampling technique that is the manager and leader of BMT Al-IttihadRumbaiPekanbaru. The result of this research shows that the position of BMT Al-Ittihad using IE Matrix, SWOT-8K Matrix and SPACE Matrix is in growth position, stabilization and aggressive. The choice of strategy after using TWOS Matrix is market penetration, market development, vertical integration, horizontal integration, and stabilization (careful.

Preconception carrier screening for multiple disorders: evaluation of a screening offer in a Dutch founder population.

Science.gov (United States)

Mathijssen, Inge B; Holtkamp, Kim C A; Ottenheim, Cecile P E; van Eeten-Nijman, Janneke M C; Lakeman, Phillis; Meijers-Heijboer, Hanne; van Maarle, Merel C; Henneman, Lidewij

2018-02-01

Technological developments have enabled carrier screening for multiple disorders. This study evaluated experiences with a preconception carrier screening offer for four recessive disorders in a Dutch founder population. Questionnaires were completed by 182 attendees pretesting and posttesting and by 137 non-attendees. Semistructured interviews were conducted with seven of the eight carrier couples. Attendees were mainly informed about the existence of screening by friends/colleagues (49%) and family members (44%). Familiarity with the genetic disorders was high. Knowledge after counseling increased (p influencers (family/friends) can be used to raise awareness of a screening offer. Our findings provide lessons for the implementation of expanded carrier screening panels in other communities and other settings.

Screening of Geomechanical Risks for Malaysian Development Field

Directory of Open Access Journals (Sweden)

Syed Najmuddin Syed Muhammad Syafiq

2017-01-01

Full Text Available Deeper drilling and exploitation of difficult reservoir is the new trend in oil and gas industry. Geomechanics study has, therefore, become a new requirement particularly for oil and gas field development. However, a complete geomechanics study is limited with the number of experts, time consuming and not a straightforward task. Therefore, there is an urgent need of a quick geomechanics screening criterion to be used as a standard guideline to evaluate the high level geomechanical risks and suitable analysis can be recommended for the identified development fields. The aim of this paper is to propose a screening criterion for geomechanical risks study based on four key parameters, drilling, depletion, injection and storage and sand production. The screening approach is designed based on Risk Assessment Matrix (RAM risk screening where the likelihood is based on a set of scores developed to specific questions. The consequence for each failure scenarios is assessed based on educated estimation of the impact towards people, asset, environment and reputation. Recommendations for geomechanical study are made based on the severity of each failure category on the RAM risk matrix. Fourteen development fields in offshore Peninsular Malaysia, offshore Sarawak and offshore Sabah are selected for the assessment. Based on results, fields in offshore Sarawak and Sabah have higher potential for geomechacnical issues mainly because of their geological settings and formation characteristics. A set of geomechanical study is proposed for each individual field for prudent management of potential geomechanics risk associated with the depletion and EOR injection scheme planned for the fields.

The Sheffield RNAi Screening Facility (SRSF): portfolio growth and technology development.

Science.gov (United States)

Brown, Stephen

2014-05-01

The Sheffield RNAi Screening Facility (SRSF) (www.rnai.group.shef.ac.uk) was established in 2008 with Wellcome Trust and University of Sheffield funding, with the task to provide the first UK RNAi screening resource for academic groups interested in identifying genes required in a diverse range of biological processes using Drosophila cell culture. The SRSF has carried out a wide range of screens varying in sizes from bespoke small-scale libraries, targeting a few hundred genes, to high-throughput, genome-wide studies. The SRSF has grown and improved with a dedicated partnership of its academic customers based mainly in the UK. We are part of the UK Academics Functional Genomics Network, participating in organizing an annual meeting in London and are part of the University of Sheffield's D3N (www.d3n.org.uk), connecting academics, biotech and pharmaceutical companies with a multidisciplinary network in Drug Discovery and Development. Recently, the SRSF has been funded by the Yorkshire Cancer Research Fund to perform genome-wide RNAi screens using human cells as part of a core facility for regional Yorkshire Universities and screens are now underway. Overall the SRSF has carried out more than 40 screens from Drosophila and human cell culture experiments.

A study of radiation hardness screening techniques of integrated circuits

International Nuclear Information System (INIS)

Wang Xuli

2002-01-01

The principle and operational procedure of Integrated Circuits (ICs) screening with irradiation-and-anneal and multicomponent regression analysis are discussed. The key technology, advantages and shortcomings of the two methods are described in contrast, and some advices are given with the state-of-the-art of the screening technology

ICRP Publication 125: Radiological Protection in Security Screening.

Science.gov (United States)

Cool, D A; Lazo, E; Tattersall, P; Simeonov, G; Niu, S

2014-07-01

The use of technologies to provide security screening for individuals and objects has been increasing rapidly, in keeping with the significant increase in security concerns worldwide. Within the spectrum of technologies, the use of ionizing radiation to provide backscatter and transmission screening capabilities has also increased. The Commission has previously made a number of statements related to the general topic of deliberate exposures of individuals in non-medical settings. This report provides advice on how the radiological protection principles recommended by the Commission should be applied within the context of security screening. More specifically, the principles of justification, optimisation of protection, and dose limitation for planned exposure situations are directly applicable to the use of ionising radiation in security screening. In addition, several specific topics are considered in this report, including the situation in which individuals may be exposed because they are concealed (‘stowaways’) in a cargo container or conveyance that may be subject to screening. The Commission continues to recommend that careful justification of screening should be considered before decisions are made to employ the technology. If a decision is made that its use is justified, the framework for protection as a planned exposure situation should be employed, including optimization of protection with the use of dose constraints and the appropriate provisions for authorisation and inspection.

Expanded newborn screening: social and ethical issues.

Science.gov (United States)

Dhondt, Jean-Louis

2010-10-01

Newborn screening and genetic testing have expanded rapidly in the last decade with the advent of multiplex (e.g., tandem mass spectrometry) and/or DNA technologies. However, screening panels include a large number of disorders, which may not meet all of the traditional screening criteria, established in late 1960s, and used for years to justify screening programs. After a period of expansion driven by technological advances, many reports have reconsidered the justification of expanded programs. Many factors have contributed to test-panel discrepancies between countries. The test-panel review methodology, the way health benefits are weighed against harms, and the socioeconomic-political environment all play a role. Expansion of screening also requires reconsideration of the infrastructure (ideally, in the context of national plans for rare diseases) to support testing, counselling, education, treatment, and follow-up. Consequently, economic aspects cannot be ignored and can be a limitation for expansion. New ethical questions have emerged: risks of discrimination or stigmatization, respect of the autonomy of persons to make decisions, parental anxiety resulting from a false positive test (especially when reporting to parents screening results for untreatable conditions identified as by-products of screening), etc. For disorders where there is not yet confirmation of benefit, it may be prudent to recommend pilot screening and to have a mechanism that can be used to adapt or even to stop a program.

First-trimester screening in pregnancies conceived by assisted reproductive technology: significance of gestational dating by oocyte retrieval or sonographic measurement of crown-rump length

DEFF Research Database (Denmark)

Gjerris, A.C.; Loft, A.; Pinborg, A.

2008-01-01

OBJECTIVES: To evaluate, in pregnancies conceived by assisted reproductive technology, whether determination of gestational age (GA) by date of oocyte aspiration (DOA) or crown-rump length (CRL) at first-trimester screening influences the distribution of serum and sonographic markers or the perfo......OBJECTIVES: To evaluate, in pregnancies conceived by assisted reproductive technology, whether determination of gestational age (GA) by date of oocyte aspiration (DOA) or crown-rump length (CRL) at first-trimester screening influences the distribution of serum and sonographic markers...... or the performance of first-trimester screening for chromosomal abnormalities. METHODS: GA was calculated using either DOA or CRL at blood sampling and nuchal translucency thickness (NT) measurement in 729 singleton pregnancies conceived by in-vitro fertilization (IVF) or intracytoplasmic sperm injection (ICSI......). Weight-corrected log multiples of the median (MoM) marker distributions specific for IVF pregnancy were established using multiple log regression and compared for DOA- and CRL-based GA calculation. RESULTS: GA determined by CRL was significantly larger, albeit slightly, than was GA determined by DOA...

Cloud-Based DDoS HTTP Attack Detection Using Covariance Matrix Approach

Directory of Open Access Journals (Sweden)

Abdulaziz Aborujilah

2017-01-01

Full Text Available In this era of technology, cloud computing technology has become essential part of the IT services used the daily life. In this regard, website hosting services are gradually moving to the cloud. This adds new valued feature to the cloud-based websites and at the same time introduces new threats for such services. DDoS attack is one such serious threat. Covariance matrix approach is used in this article to detect such attacks. The results were encouraging, according to confusion matrix and ROC descriptors.

Amorphous metal matrix composite ribbons

International Nuclear Information System (INIS)

Barczy, P.; Szigeti, F.

1998-01-01

Composite ribbons with amorphous matrix and ceramic (SiC, WC, MoB) particles were produced by modified planar melt flow casting methods. Weldability, abrasive wear and wood sanding examinations were carried out in order to find optimal material and technology for elevated wear resistance and sanding durability. The correlation between structure and composite properties is discussed. (author)

Population newborn screening for inherited metabolic disease: current UK perspectives.

Science.gov (United States)

Green, A; Pollitt, R J

1999-06-01

Some of the generally accepted criteria for screening programmes are inappropriate for newborn metabolic screening as they ignore the family dimension and the importance of timely genetic information. Uncritical application of such criteria creates special difficulties for screening by tandem mass spectrometry, which can detect a range diseases with widely different natural histories and responsiveness to treatment. Further difficulties arise from increasing demands for direct proof of the effects of screening on long-term morbidity and mortality. The randomized controlled trial is held to be the gold standard, but for ethical and practical reasons it will be impossible to achieve for such relatively rare diseases. This approach also oversimplifies the complex matrix of costs and benefits of newborn metabolic screening. A more workable approach could involve Bayesian synthesis, combining quantitative performance data from carefully designed prospective pilot studies of screening with existing experience of the natural history, diagnosis, and management of the individual disorders concerned.

Systematic review of model-based cervical screening evaluations.

Science.gov (United States)

Mendes, Diana; Bains, Iren; Vanni, Tazio; Jit, Mark

2015-05-01

Optimising population-based cervical screening policies is becoming more complex due to the expanding range of screening technologies available and the interplay with vaccine-induced changes in epidemiology. Mathematical models are increasingly being applied to assess the impact of cervical cancer screening strategies. We systematically reviewed MEDLINE®, Embase, Web of Science®, EconLit, Health Economic Evaluation Database, and The Cochrane Library databases in order to identify the mathematical models of human papillomavirus (HPV) infection and cervical cancer progression used to assess the effectiveness and/or cost-effectiveness of cervical cancer screening strategies. Key model features and conclusions relevant to decision-making were extracted. We found 153 articles meeting our eligibility criteria published up to May 2013. Most studies (72/153) evaluated the introduction of a new screening technology, with particular focus on the comparison of HPV DNA testing and cytology (n = 58). Twenty-eight in forty of these analyses supported HPV DNA primary screening implementation. A few studies analysed more recent technologies - rapid HPV DNA testing (n = 3), HPV DNA self-sampling (n = 4), and genotyping (n = 1) - and were also supportive of their introduction. However, no study was found on emerging molecular markers and their potential utility in future screening programmes. Most evaluations (113/153) were based on models simulating aggregate groups of women at risk of cervical cancer over time without accounting for HPV infection transmission. Calibration to country-specific outcome data is becoming more common, but has not yet become standard practice. Models of cervical screening are increasingly used, and allow extrapolation of trial data to project the population-level health and economic impact of different screening policy. However, post-vaccination analyses have rarely incorporated transmission dynamics. Model calibration to country

Market screening of natural gas reformers

International Nuclear Information System (INIS)

Themsen, J.; Pagh Nielsen, M.; Knudsen Kaer, S.

2005-01-01

This report presents results from the project: Market screening of natural gas reformers. The project objective was to screen the natural gas reformers available on the international market. The technology is developing rapidly, and the results from this project will assist in determining the focus for the future Danish activities and in setting up ambitious and realistic targets. The reformer screening is partly based on AAU and Dantherm's experiences from previous studies, and the screening has been further extended with a number of activities, including seminars and contact with some of the most interesting suppliers. (BA)

Human aqueous humor levels of transforming growth factor-β2: Association with matrix metalloproteinases/tissue inhibitors of matrix metalloproteinases

OpenAIRE

Jia, Yan; Yue, Yu; Hu, Dan-Ning; Chen, Ji-Li; Zhou, Ji-Bo

2017-01-01

The present study aims to investigate the association of transforming growth factor-β2 (TGF-β2) and matrix metalloproteinases (MMPs), MMP-2 and MMP-3, and tissue inhibitors of matrix metalloproteinases (TIMPs), TIMP-1, TIMP-2 and TIMP-3 in the aqueous humor of patients with high myopia or cataracts. The levels of TGF-β2 and MMPs/TIMPs were measured with the Luminex xMAP Technology using commercially available Milliplex xMAP kits. The association between TGF-β2 and MMPs/TIMPs levels was analyz...

Curcumin: a potential candidate for matrix metalloproteinase inhibitors.

Science.gov (United States)

Kumar, Dileep; Kumar, Manish; Saravanan, Chinnadurai; Singh, Sushil Kumar

2012-10-01

Curcumin, a natural yellow pigment of turmeric, has become focus of interest with regard to its role in regulation of matrix metalloproteinases (MMPs). MMPs are metal-dependent endopeptidases capable of degrading components of the extracellular matrix. MMPs are involved in chronic diseases such as arthritis, Alzheimer's disease, psoriasis, chronic obstructive pulmonary disease, asthma, cancer, neuropathic pain, and atherosclerosis. Curcumin regulates the expression and secretion of various MMPs. This review documents the matrix metalloproteinase inhibitory activity of curcumin on various diseases viz., cancer, arthritis, and ulcer. Finally, the steps to be taken for getting potent curcuminoids have also been discussed in the structure-activity relationship (SAR) section. From this review, readers can get answer to the question: Is curcumin a potential MMPI candidate? Numerous approaches have been taken to beget a molecule with specificity restricted to a particular MMP as well as good oral bioavailability; however, nearly all the molecules lack these criteria. Using quantitative structure-activity relationship (QSAR) modeling and virtual screening, new analogs of curcumin can be designed which will be selectively inhibiting different MMPs.

Emerging Educational Institutional Decision-Making Matrix

Science.gov (United States)

Ashford-Rowe, Kevin H.; Holt, Marnie

2011-01-01

The "emerging educational institutional decision-making matrix" is developed to allow educational institutions to adopt a rigorous and consistent methodology of determining which of the myriad of emerging educational technologies will be the most compelling for the institution, particularly ensuring that it is the educational or pedagogical but…

High performance passive matrix electrochromic display

International Nuclear Information System (INIS)

Aliev, A.E.

2003-01-01

A matrix addressable electrochromic display (ECD) based on solid polymer electrolyte screen-printed on the surface of nano structured WO 3 +0.1TiO 2 electrodes, in which all pixels were insulted by negative photoresist material has been developed. Five types of nano structured films produced by a sol-gel method were investigated to enhance the electrochemical, optical, and mechanical properties of electrochromic tungsten oxide films. The film based on WO 3-x +0.1TiO 2-y sol-gel solution mixed with 32 mol.% oxalic acid was found to be stable and has excellent characteristics in coloring/bleaching kinetics. The ECD used nano structured electrochromic tungsten trioxide layer protected by SiO 2 -CeO 2 -Li 2 O thin film solid electrolyte, screen-printed solid polymer electrolyte mixed with white TiO 2 pigment (P25), and metallic counter electrode covered with carbon layer, has exhibited fast switching, excellent memory effect and substantially free from image diffusion and cross talk effects. (author)

The Matrix Trilogy and Technology Teaching

Directory of Open Access Journals (Sweden)

Marcos A. Costa

2013-12-01

Full Text Available In a world full of dynamic and alternative forms of learning more innovation should be encouraged and applied consistently so that the student feel more interest in curriculum content. As the student observes such content not only through analogies, but also through production film, which has references and influences from different sources, we can find various information that include mainly the technological learning, not excluding mathematics, physics, philosophy and religious studies. We make it possible through a concept innovation of teaching which is described, coherently, as a knowledge transmission and not as broadcasting of values as some authors try to argue. So, with this approach is possible, not only, to make that some students identify themselves more with the theme, because they have a natural tendency for technology and another areas, but also can promote the learning of those who do not have such intimacy with these areas

Toxicophore exploration as a screening technology for drug design and discovery: techniques, scope and limitations.

Science.gov (United States)

Singh, Pankaj Kumar; Negi, Arvind; Gupta, Pawan Kumar; Chauhan, Monika; Kumar, Raj

2016-08-01

Toxicity is a common drawback of newly designed chemotherapeutic agents. With the exception of pharmacophore-induced toxicity (lack of selectivity at higher concentrations of a drug), the toxicity due to chemotherapeutic agents is based on the toxicophore moiety present in the drug. To date, methodologies implemented to determine toxicophores may be broadly classified into biological, bioanalytical and computational approaches. The biological approach involves analysis of bioactivated metabolites, whereas the computational approach involves a QSAR-based method, mapping techniques, an inverse docking technique and a few toxicophore identification/estimation tools. Being one of the major steps in drug discovery process, toxicophore identification has proven to be an essential screening step in drug design and development. The paper is first of its kind, attempting to cover and compare different methodologies employed in predicting and determining toxicophores with an emphasis on their scope and limitations. Such information may prove vital in the appropriate selection of methodology and can be used as screening technology by researchers to discover the toxicophoric potentials of their designed and synthesized moieties. Additionally, it can be utilized in the manipulation of molecules containing toxicophores in such a manner that their toxicities might be eliminated or removed.

Vision Screening

Science.gov (United States)

1993-01-01

The Visi Screen OSS-C, marketed by Vision Research Corporation, incorporates image processing technology originally developed by Marshall Space Flight Center. Its advantage in eye screening is speed. Because it requires no response from a subject, it can be used to detect eye problems in very young children. An electronic flash from a 35 millimeter camera sends light into a child's eyes, which is reflected back to the camera lens. The photorefractor then analyzes the retinal reflexes generated and produces an image of the child's eyes, which enables a trained observer to identify any defects. The device is used by pediatricians, day care centers and civic organizations that concentrate on children with special needs.

Use of Single-Tow Ceramic Matrix Minicomposites to Determine Fundamental Room and Elevated Temperature Properties

Science.gov (United States)

Almansour, Amjad S.

characterization methodology was used to screen and characterize slurry-derived mullite bond coated minicomposites for enhanced oxidation and creep resistance. Finally, this study shows valuable testing methodologies and models approach for use in screening, developing and improving new generation ceramic matrix composites.

Mobile Screens: The Visual Regime of Navigation

NARCIS (Netherlands)

Verhoeff, N.

2012-01-01

In this book on screen media, space, and mobility I compare synchronically, as well as diachronically, diverse and variegated screen media - their technologies and practices – as sites for virtual mobility and navigation. Mobility as a central trope can be found on the multiple levels that are

Transforming Security Screening With Biometrics

National Research Council Canada - National Science Library

Hearnsberger, Brian J

2003-01-01

... and identity theft to dramatically improve physical security. Today, biometric technology could be implemented to transform physical security by enhancing screening procedures currently in use at U.S...

Cost-Effectiveness of HBV and HCV Screening Strategies – A Systematic Review of Existing Modelling Techniques

Science.gov (United States)

Geue, Claudia; Wu, Olivia; Xin, Yiqiao; Heggie, Robert; Hutchinson, Sharon; Martin, Natasha K.; Fenwick, Elisabeth; Goldberg, David

2015-01-01

Introduction Studies evaluating the cost-effectiveness of screening for Hepatitis B Virus (HBV) and Hepatitis C Virus (HCV) are generally heterogeneous in terms of risk groups, settings, screening intervention, outcomes and the economic modelling framework. It is therefore difficult to compare cost-effectiveness results between studies. This systematic review aims to summarise and critically assess existing economic models for HBV and HCV in order to identify the main methodological differences in modelling approaches. Methods A structured search strategy was developed and a systematic review carried out. A critical assessment of the decision-analytic models was carried out according to the guidelines and framework developed for assessment of decision-analytic models in Health Technology Assessment of health care interventions. Results The overall approach to analysing the cost-effectiveness of screening strategies was found to be broadly consistent for HBV and HCV. However, modelling parameters and related structure differed between models, producing different results. More recent publications performed better against a performance matrix, evaluating model components and methodology. Conclusion When assessing screening strategies for HBV and HCV infection, the focus should be on more recent studies, which applied the latest treatment regimes, test methods and had better and more complete data on which to base their models. In addition to parameter selection and associated assumptions, careful consideration of dynamic versus static modelling is recommended. Future research may want to focus on these methodological issues. In addition, the ability to evaluate screening strategies for multiple infectious diseases, (HCV and HIV at the same time) might prove important for decision makers. PMID:26689908

Screening Risk Evaluation methodology

International Nuclear Information System (INIS)

Hopper, K.M.

1994-01-01

The Screening Risk Evaluation (SRE) Guidance document is a set of guidelines provided for the uniform implementation of SREs performed on D ampersand D facilities. These guidelines are designed specifically for the completion of the second (semi-quantitative screening) phase of the D ampersand D Risk-Based Process. The SRE Guidance produces screening risk scores reflecting levels of risk through the use of risk ranking indices. Five types of possible risk are calculated from the SRE: current releases, worker exposures, future releases, physical hazards, and criticality. The Current Release Index (CRI) calculates the risk to human health and the environment from ongoing or probable releases within a one year time period. The Worker Exposure Index (WEI) calculates the risk to workers, occupants, and visitors in D ampersand D facilities of contaminant exposure. The Future Release Index (FRI) calculates the risk of future releases of contaminants, after one year, to human health and the environment. The Physical Hazards Index (PHI) calculates the risk-to human health due to factors other than that of contaminants. The index of Criticality is approached as a modifying factor to the entire SRE, due to the fact that criticality issues are strictly regulated under DOE. Screening risk results will be tabulated in matrix form and Total Risk will be calculated (weighted equation) to produce a score on which to base early action recommendations. Other recommendations from the screening risk scores will be made based either on individual index scores or from reweighted Total Risk calculations. All recommendations based on the SRE will be made based on a combination of screening risk scores, decision drivers, and other considerations, determined on a project by project basis. The SRE is the first and most important step in the overall D ampersand D project level decision making process

Design and Polarization Characteristics Analysis of Dihedral Based on Salisbury Screen

Directory of Open Access Journals (Sweden)

Zhang Ran

2016-12-01

Full Text Available Salisbury screens have a number of unique electromagnetic scattering characteristics. When appropriately designed, the Salisbury screen can reach the radar target signature transform. Based on the electromagnetic scattering characteristics of the Salisbury screen, we designed a novel dihedral corner, and theoretically analyzed and simulated its electromagnetic scattering characteristics in this study. The results reveal the monostatic radar cross section curves of the 90°and 60° Salisbury screen dihedral and metal dihedral, respectively. Taking an orthogonal dihedral corner as an example, we obtained the polarization scattering matrixes for different incident degrees. In addition, we investigated the influence of illumination frequency, target gestures, and other key factors on the polarization characteristics of the Salisbury screen dihedral corner. The theoretical and simulation analysis results show that compared with the conventional metal dihedral corner, the Salisbury screen dihedral corner significantly influences the scattering characteristics and will have potential application in electronic warfare.

Development of novel vaccines using DNA shuffling and screening strategies.

Science.gov (United States)

Locher, Christopher P; Soong, Nay Wei; Whalen, Robert G; Punnonen, Juha

2004-02-01

DNA shuffling and screening technologies recombine and evolve genes in vitro to rapidly obtain molecules with improved biological activity and fitness. In this way, genes from related strains are bred like plants or livestock and their successive progeny are selected. These technologies have also been called molecular breeding-directed molecular evolution. Recent developments in bioinformatics-assisted computer programs have facilitated the design, synthesis and analysis of DNA shuffled libraries of chimeric molecules. New applications in vaccine development are among the key features of DNA shuffling and screening technologies because genes from several strains or antigenic variants of pathogens can be recombined to create novel molecules capable of inducing immune responses that protect against infections by multiple strains of pathogens. In addition, molecules such as co-stimulatory molecules and cytokines have been evolved to have improved T-cell proliferation and cytokine production compared with the wild-type human molecules. These molecules can be used to immunomodulate vaccine responsiveness and have multiple applications in infectious diseases, cancer, allergy and autoimmunity. Moreover, DNA shuffling and screening technologies can facilitate process development of vaccine manufacturing through increased expression of recombinant polypeptides and viruses. Therefore, DNA shuffling and screening technologies can overcome some of the challenges that vaccine development currently faces.

Ceramic technology for advanced heat engines project

Energy Technology Data Exchange (ETDEWEB)

1990-09-01

The Ceramic Technology for Advanced Heat Engines Project was developed by the Department of Energy's Office of Transportation Systems in Conservation and Renewable Energy. This project was developed to meet the ceramic technology requirements of the OTT's automotive technology programs. This project is managed by ORNL and is closely coordinated with complementary ceramics tasks funded by other DOE offices, NASA, DoD, and industry. Research is discussed under the following topics; Turbomilling of SiC Whiskers; microwave sintering of silicon nitride; and milling characterization; processing of monolithics; silicon nitride matrix; oxide matrix; silicate matrix; thermal and wear coatings; joining; design; contact interfaces; time-dependent behavior; environmental effects; fracture mechanics; nondestructive evaluation; and technology transfer. References, figures, and tables are included with each topic.

A virtual test of screening technology based on the AGEIA PhysX

Energy Technology Data Exchange (ETDEWEB)

Ai-min Li; Rui-ling Lv; Chu-sheng Liu [China University of Mining and Technology, Xuzhou (China). School of Mechanical and Electrical Engineering

2008-06-15

The authors have created a virtual test of vibration particle-screening using Autodesk's 3ds Max software, the MAXScript scripting language and the AGEIA PhysX physics processing unit (PPU). The affect of various parameters on screening efficiency were modeled. The parameters included vibration amplitude, frequency and direction. The length and inclination of the vibrating surface were also varied. The virtual experiment is in basic agreement with results predicted from screening theory. This shows that the virtual screener can be used for preliminary investigations and the results used to evaluate screen design. In addition it can help with theoretical research. 11 refs., 7 figs., 7 tabs.

Improvement of an X-ray imaging detector based on a scintillating guides screen

CERN Document Server

Badel, X; Linnros, J; Kleimann, P; Froejdh, C; Petersson, C S

2002-01-01

An X-ray imaging detector has been developed for dental applications. The principle of this detector is based on application of a silicon charge coupled device covered by a scintillating wave-guide screen. Previous studies of such a detector showed promising results concerning the spatial resolution but low performance in terms of signal to noise ratio (SNR) and sensitivity. Recent results confirm the wave-guiding properties of the matrix and show improvement of the detector in terms of response uniformity, sensitivity and SNR. The present study is focussed on the fabrication of the scintillating screen where the principal idea is to fill a matrix of Si pores with a CsI scintillator. The photoluminescence technique was used to prove the wave-guiding property of the matrix and to inspect the filling uniformity of the pores. The final detector was characterized by X-ray evaluation in terms of spatial resolution, light output and SNR. A sensor with a spatial resolution of 9 LP/mm and a SNR over 50 has been achie...

Matrix completion by deep matrix factorization.

Science.gov (United States)

Fan, Jicong; Cheng, Jieyu

2018-02-01

Conventional methods of matrix completion are linear methods that are not effective in handling data of nonlinear structures. Recently a few researchers attempted to incorporate nonlinear techniques into matrix completion but there still exists considerable limitations. In this paper, a novel method called deep matrix factorization (DMF) is proposed for nonlinear matrix completion. Different from conventional matrix completion methods that are based on linear latent variable models, DMF is on the basis of a nonlinear latent variable model. DMF is formulated as a deep-structure neural network, in which the inputs are the low-dimensional unknown latent variables and the outputs are the partially observed variables. In DMF, the inputs and the parameters of the multilayer neural network are simultaneously optimized to minimize the reconstruction errors for the observed entries. Then the missing entries can be readily recovered by propagating the latent variables to the output layer. DMF is compared with state-of-the-art methods of linear and nonlinear matrix completion in the tasks of toy matrix completion, image inpainting and collaborative filtering. The experimental results verify that DMF is able to provide higher matrix completion accuracy than existing methods do and DMF is applicable to large matrices. Copyright © 2017 Elsevier Ltd. All rights reserved.

A generic approach for expanding homolog-targeted residue screening of sulfonamides using a fast matrix separation and class-specific fragmentation-dependent acquisition with a hybrid quadrupole-linear ion trap mass spectrometer

International Nuclear Information System (INIS)

Huang Chunlin; Guo Bin; Wang Xiaoying; Li Jie; Zhu Weitao; Chen Bo; Ouyang Shan; Yao Shouzhuo

2012-01-01

Highlights: ► Generic homolog-targeted screening approach for multi-residual sulfonamide analogs. ► Single-tube extraction/partitioning-multifunction adsorption cleanup for direct injection. ► Class-specific fragmentation for expanding coverage of N 4 -acetyl and N-OH metabolites. ► PreS–IDA–EPI in LC–QqLIT for simultaneous screening and confirmation of real samples. - Abstract: A generic and efficient homolog-targeted approach was used to expand screening and detection of target class of sulfonamides and structural analogs, based on a fast single-tube extraction/partitioning-multifunction adsorption cleanup (SEP/MAC) for class-specific fragmentation-dependent acquisition with a liquid chromatography–hybrid triple-quadrupole linear ion trap mass spectrometer (LC–QqLIT). By combining the two-stage process conducted in a single tube as one-pot protocol, the straightforward SEP/MAC procedure was optimized to offer clean extracts with reasonable recovery (71–109% with RSDs 4 -acetyl and hydroxylamine metabolites plus their possible dimers. Moreover, the PreS-triggered automatically enhanced product ion spectral acquisition enabled simultaneous screening, profiling and confirmation of an unlimited number of analytes belonging to the sulfonamide class within a single analysis. The validation and application results of the generic SEP/MAC-based LC–QqLIT strategy consistently demonstrated favorable performances with acceptable accuracy (67–116%), precision (RSDs −1 ) to meet the acceptance criteria for all the sulfonamide–tissue combinations. Thus, the integration of the matrix-independent SEP/MAC procedure and the multiparameter matching algorithm with the unit-resolution LC–QqLIT instrument can serve as a valuable semi-targeted discovery strategy for rapid screening and reliable quantitative/confirmatory analysis of real samples.

Improved Soluble ScFv ELISA Screening Approach for Antibody Discovery Using Phage Display Technology.

Science.gov (United States)

Tohidkia, Mohammad R; Sepehri, Maryam; Khajeh, Shirin; Barar, Jaleh; Omidi, Yadollah

2017-09-01

Phage display technology (PDT) is a powerful tool for the isolation of recombinant antibody (Ab) fragments. Using PDT, target molecule-specific phage-Ab clones are enriched through the "biopanning" process. The individual specific binders are screened by the monoclonal scFv enzyme-linked immunosorbent assay (ELISA) that may associate with inevitable false-negative results. Thus, in this study, three strategies were investigated for optimization of the scFvs screening using Tomlinson I and J libraries, including (1) optimizing the expression of functional scFvs, (2) improving the sensitivity of ELISA, and (3) preparing different samples containing scFvs. The expression of all scFv Abs was significantly enhanced when scFv clones were cultivated in the terrific broth (TB) medium at the optimum temperature of 30 °C. The protein A-conjugated with horseradish peroxidase (HRP) was found to be a well-suited reagent for the detection of Ag-bound scFvs in comparison with either anti-c-myc Ab or the mixing procedure. Based on our findings, it seems there is no universal media supplement for an improved expression of all scFvs derived from both Tomlinson I and J libraries. We thus propose that expression of scFv fragments in a microplate scale is largely dependent on a variety of parameters, in particular the scFv clones and relevant sequences.

Rapid screening of radioactivity in food for emergency response.

Science.gov (United States)

Bari, A; Khan, A J; Semkow, T M; Syed, U-F; Roselan, A; Haines, D K; Roth, G; West, L; Arndt, M

2011-06-01

This paper describes the development of methods for the rapid screening of gross alpha (GA) and gross beta (GB) radioactivity in liquid foods, specifically, Tang drink mix, apple juice, and milk, as well as screening of GA, GB, and gamma radioactivity from surface deposition on apples. Detailed procedures were developed for spiking of matrices with (241)Am (alpha radioactivity), (90)Sr/(90)Y (beta radioactivity), and (60)Co, (137)Cs, and (241)Am (gamma radioactivity). Matrix stability studies were performed for 43 days after spiking. The method for liquid foods is based upon rapid digestion, evaporation, and flaming, followed by gas proportional (GP) counting. For the apple matrix, surface radioactivity was acid-leached, followed by GP counting and/or gamma spectrometry. The average leaching recoveries from four different apple brands were between 63% and 96%, and have been interpreted on the basis of ion transport through the apple cuticle. The minimum detectable concentrations (MDCs) were calculated from either the background or method-blank (MB) measurements. They were found to satisfy the required U.S. FDA's Derived Intervention Levels (DILs) in all but one case. The newly developed methods can perform radioactivity screening in foods within a few hours and have the potential to capacity with further automation. They are especially applicable to emergency response following accidental or intentional contamination of food with radioactivity. Published by Elsevier Ltd.

Rapid screening of radioactivity in food for emergency response

International Nuclear Information System (INIS)

Bari, A.; Khan, A.J.; Semkow, T.M.; Syed, U.-F.; Roselan, A.; Haines, D.K.; Roth, G.; West, L.; Arndt, M.

2011-01-01

This paper describes the development of methods for the rapid screening of gross alpha (GA) and gross beta (GB) radioactivity in liquid foods, specifically, Tang drink mix, apple juice, and milk, as well as screening of GA, GB, and gamma radioactivity from surface deposition on apples. Detailed procedures were developed for spiking of matrices with 241 Am (alpha radioactivity), 90 Sr/ 90 Y (beta radioactivity), and 60 Co, 137 Cs, and 241 Am (gamma radioactivity). Matrix stability studies were performed for 43 days after spiking. The method for liquid foods is based upon rapid digestion, evaporation, and flaming, followed by gas proportional (GP) counting. For the apple matrix, surface radioactivity was acid-leached, followed by GP counting and/or gamma spectrometry. The average leaching recoveries from four different apple brands were between 63% and 96%, and have been interpreted on the basis of ion transport through the apple cuticle. The minimum detectable concentrations (MDCs) were calculated from either the background or method-blank (MB) measurements. They were found to satisfy the required U.S. FDA's Derived Intervention Levels (DILs) in all but one case. The newly developed methods can perform radioactivity screening in foods within a few hours and have the potential to capacity with further automation. They are especially applicable to emergency response following accidental or intentional contamination of food with radioactivity.

Influence of the UV radiation on the screen-printed pH-sensitive layers based on graphene and ruthenium dioxide

Science.gov (United States)

Pepłowski, A.; Grudziński, D.; Raczyński, T.; Wróblewski, G.; Janczak, D.; Jakubowska, M.

2017-08-01

Electrodes for measuring pH of the solution were fabricated by the means of screen-printing technology. Potentiometric sensors' layers comprised of composite with polymer matrix and graphene nanoplatelets/ruthenium (IV) oxide nanopowder as functional phase. Transceivers were printed on the elastic PMMA foil. Regarding potential application of the sensors in the wearable devices, dynamic response of the electrodes to changing ultraviolet radiation levels was assessed, since RuO2 is reported to be UV-sensitive. Observed changes of the electrodes' potential were of sub-millivolt magnitude, being comparable to simultaneously observed signal drift. Given this stability under varying UV conditions and previously verified good flexibility, fabricated sensors meet the requirements for wearable applications.

Feasibility of computerized screening for intimate partner violence in a pediatric emergency department.

Science.gov (United States)

Scribano, Philip V; Stevens, Jack; Marshall, Jessica; Gleason, Erica; Kelleher, Kelly J

2011-08-01

This study aimed to evaluate the feasibility of caregiver-initiated computerized screening in a pediatric emergency department (ED) to identify home safety risks, with a specific emphasis on intimate partner violence (IPV). Home safety screening kiosks were developed using information technology as the first step in a plan to decrease family violence. Caregivers self-initiated a standard-of-care screening process that included both non-IPV and IPV items. An ED social worker received an automated text page and printed summary of the findings when a caregiver endorsed IPV. System activity was tracked by comparing frequency of completed screens to the daily ED census and by determining the percentage of completed screens that were positive for IPV. The reliability of the technology was evaluated as percentage of days of system downtime. Meetings with ED personnel and direct observations of families were conducted to identify potential barriers and successes to the technology utilization. During a 15-month period, 13,057 computerized screens occurred, with a 4-fold increase in the computerized screening rate after ED triage nurses became champions of these efforts. Fourteen percent of the computerized screens were positive for IPV. The reliability of the technology was considered quite high, with rare system downtime (4.2% of days) reported during the 15 months. There were several themes identified by caregivers and providers regarding barriers to successful use of the safety screening. A reliable, caregiver-initiated system is possible to offer consistent opportunity to conduct unobtrusive, private screening for IPV and other home safety concerns.

Screening of the hearing of newborns - Update

Directory of Open Access Journals (Sweden)

von Voß, Hubertus

2006-11-01

Full Text Available Introduction: Permanent congenital bilateral hearing loss (CHL of moderate or greater degree (≥40 dB HL is a rare disease, with a prevalence of about 1 to 3 per 1000 births. However, it is one of the most frequent congenital diseases. Reliance on physician observation and parental recognition has not been successful in the past in detecting significant hearing loss in the first year of life. With this strategy significant hearing losses have been detected in the second year of life. With two objective technologies based on physiologic response to sound, otoacoustic emissions (OAE and auditory brainstem response (ABR hearing screening in the first days of life is made possible. Objectives: The objective of this health technology assessment report is to update the evaluation on clinical effectiveness and cost-effectiveness of newborn hearing screening programs. Universal newborn hearing screening (UHNS (i, selective screening of high risk newborns (ii, and the absence of a systematic screening program are compared for age at identification and age at hearing aid fitting of children with hearing loss. Secondly the potential benefits of early intervention are analysed. Costs and cost-effectiveness of newborn hearing screening programs are determined. This report is intended to make a contribution to the decision making whether and under which conditions a newborn hearing screening program should be reimbursed by the statutory sickness funds in Germany. Methods: This health technology assessment report updates a former health technology assessment (Kunze et al. 2004 [1]. A systematic review of the literature was conducted, based on a documented search and selection of the literature using predefined inclusion and exclusion criteria and a documented extraction and appraisal of the included studies. To assess the cost-effectiveness of the different screening strategies in Germany the decision analytic Markov state model which had been developed in

Does screen size matter for smartphones? Utilitarian and hedonic effects of screen size on smartphone adoption.

Science.gov (United States)

Kim, Ki Joon; Sundar, S Shyam

2014-07-01

This study explores the psychological effects of screen size on smartphone adoption by proposing an extended Technology Acceptance Model (TAM) that integrates an empirical comparison between large and small screens with perceived control, affective quality, and the original TAM constructs. A structural equation modeling analysis was conducted on data collected from a between-subjects experiment (N=130) in which users performed a web-based task on a smartphone with either a large (5.3 inches) or a small (3.7 inches) screen. Results show that a large screen, compared to a small screen, is likely to lead to higher smartphone adoption by simultaneously promoting both the utilitarian and hedonic qualities of smartphones, which in turn positively influence perceived ease of use of-and attitude toward-the device respectively. Implications and directions for future research are discussed.

Microstructure, Friction and Wear of Aluminum Matrix Composites

Science.gov (United States)

Florea, R. M.

2018-06-01

MMCs are made by dispersing a reinforcing material into a metal matrix. They are prepared by casting, although several technical challenges exist with casting technology. Achieving a homogeneous distribution of reinforcement within the matrix is one such challenge, and this affects directly on the properties and quality of composite. The aluminum alloy composite materials consist of high strength, high stiffness, more thermal stability, more corrosion and wear resistance, and more fatigue life. Aluminum alloy materials found to be the best alternative with its unique capacity of designing the materials to give required properties. In this work a composite is developed by adding silicon carbide in Aluminum metal matrix by mass ratio 5%, 10% and 15%. Mechanical tests such as hardness test and microstructure test are conducted.

Molecular Cues Guiding Matrix Stiffness in Liver Fibrosis

Directory of Open Access Journals (Sweden)

Takaoki Saneyasu

2016-01-01

Full Text Available Tissue and matrix stiffness affect cell properties during morphogenesis, cell growth, differentiation, and migration and are altered in the tissue remodeling following injury and the pathological progression. However, detailed molecular mechanisms underlying alterations of stiffness in vivo are still poorly understood. Recent engineering technologies have developed powerful techniques to characterize the mechanical properties of cell and matrix at nanoscale levels. Extracellular matrix (ECM influences mechanical tension and activation of pathogenic signaling during the development of chronic fibrotic diseases. In this short review, we will focus on the present knowledge of the mechanisms of how ECM stiffness is regulated during the development of liver fibrosis and the molecules involved in ECM stiffness as a potential therapeutic target for liver fibrosis.

Rapid and selective screening of melamine in bovine milk using molecularly imprinted matrix solid-phase dispersion coupled with liquid chromatography-ultraviolet detection.

Science.gov (United States)

Yan, Hongyuan; Cheng, Xiaoling; Sun, Ning; Cai, Tianyu; Wu, Ruijun; Han, Kun

2012-11-01

A simple, convenient and high selective molecularly imprinted matrix solid-phase dispersion (MI-MSPD) using water-compatible cyromazine-imprinted polymer as adsorbent was proposed for the rapid screening of melamine from bovine milk coupled with liquid chromatography-ultraviolet detection. The molecularly imprinted polymers (MIPs) synthesized by cyromazine as dummy template and reformative methanol-water system as reaction medium showed higher affinity and selectivity to melamine, and so they were applied as the specific dispersant of MSPD to extraction of melamine and simultaneously eliminate the effect of template leakage on quantitative analysis. Under the optimized conditions, good linearity was obtained in a range of 0.24-60.0μgg(-1) with the correlation coefficient of 0.9994. The recoveries of melamine at three spiked levels were ranged from 86.0 to 96.2% with the relative standard deviation (RSD)≤4.0%. This proposed MI-MSPD method combined the advantages of MSPD and MIPs, and could be used as an alternative tool for analyzing the residues of melamine in complex milk samples. Copyright © 2012 Elsevier B.V. All rights reserved.

Matrix solution to longitudinal impedance of multi-layer circular structures

Energy Technology Data Exchange (ETDEWEB)

Hahn,H.

2008-10-01

A matrix method in which radial wave propagation is treated in analogy to longitudinal transmission lines is presented and applied to finding the longitudinal coupling impedance of axially symmetric multi-layer beam tubes. The method is demonstrated in the case of a Higher Order Mode ferrite absorber with an inserted coated ceramic beam tube. The screening of the ferrite damping properties by the dielectric beam tube is discussed.

Organisational aspects of mammography screening in digital settings: First experiences of Luxembourg

International Nuclear Information System (INIS)

Shannoun, F.; Schanck, J. M.; Scharpantgen, A.; Wagnon, M. C.; Ben Daoud, M.; Back, C.

2008-01-01

Luxembourg has been conducting a breast cancer screening programme since 1992, like a large number of other European countries, as early detection and treatment of breast cancer have been proven to reduce mortality. The majority of these screening programmes are based on analogue X-ray technology and have optimised their organisation of transporting, archiving and reading with respect to films. Last decade is marked by enormous developments in digital mammography. Different technologies such as flat panel-, computed radiography- and scanning systems became available. Digital mammography is expected to have a major impact on quality and organisation of breast cancer screening programmes. Screening programmes are now faced with a huge challenge of incorporating the digital technology, including implementation of electronic image exchange, conception of new electronic work-flow, establishing adapted quality assurance programmes and training of radiologists and technical personnel. Initial experiences of the Luxembourg approach in organising digital mammography screening and its quality assurance are reported. (authors)

Screen printing technology applied to silicon solar cell fabrication

Science.gov (United States)

Thornhill, J. W.; Sipperly, W. E.

1980-01-01

The process for producing space qualified solar cells in both the conventional and wraparound configuration using screen printing techniques was investigated. Process modifications were chosen that could be easily automated or mechanized. Work was accomplished to optimize the tradeoffs associated with gridline spacing, gridline definition and junction depth. An extensive search for possible front contact metallization was completed. The back surface field structures along with the screen printed back contacts were optimized to produce open circuit voltages of at least an average of 600 millivolts. After all intended modifications on the process sequence were accomplished, the cells were exhaustively tested. Electrical tests at AMO and 28 C were made before and after boiling water immersion, thermal shock, and storage under conditions of high temperature and high humidity.

New screening methodology for selection of polymeric materials for transdermal drug delivery devices

Science.gov (United States)

Falcone, Roberto P.

As medical advances extend the human lifespan, the level of chronic illnesses will increase and thus straining the needs of the health care system that, as a result, governments will need to balance expenses without upsetting national budgets. Therefore, the selection of a precise and affordable drug delivery technology is seen as the most practical solution for governments, health care professionals, and consumers. Transdermal drug delivery patches (TDDP) are one of the best economical technologies that are favored by pharmaceutical companies and physicians alike because it offers fewer complications when compared to other delivery technologies. TDDP provides increased efficiency, safety and convenience for the patient. The TDDP segment within the US and Global drug delivery markets were valued at 5.6 and 12.7 billion respectively in 2009. TDDP is forecasted to reach $31.5 billion in 2015. The present TDDP technology involves the fabrication of a patch that consists of a drug embedded in a polymeric matrix. The diffusion coefficient is determined from the slope of the cumulative drug release versus time. It is a trial and error method that is time and labor consuming. With all the advantages that TDDPs can offer, the methodology used to achieve the so-called optimum design has resulted in several incidents where the safety and design have been put to question in recent times (e.g. Fentanyl). A more logical screening methodology is needed. This work shows the use of a modified Duda Zielinsky equation (DZE). Experimental release curves from commercial are evaluated. The experimental and theoretical Diffusion Coefficient values are found to be within the limits specified in the patent literature. One interesting finding is that the accuracy of the DZE is closer to experimental values when the type of Molecular Shape and Radius are used. This work shows that the modified DZE could be used as an excellent screening tool to determine the optimal polymeric matrices that

Automated screening for retinopathy

Directory of Open Access Journals (Sweden)

A. S. Rodin

2014-07-01

Full Text Available Retinal pathology is a common cause of an irreversible decrease of central vision commonly found amongst senior population. Detection of the earliest signs of retinal diseases can be facilitated by viewing retinal images available from the telemedicine networks. To facilitate the process of retinal images, screening software applications based on image recognition technology are currently on the various stages of development.Purpose: To develop and implement computerized image recognition software that can be used as a decision support technologyfor retinal image screening for various types of retinopathies.Methods: The software application for the retina image recognition has been developed using C++ language. It was tested on dataset of 70 images with various types of pathological features (age related macular degeneration, chorioretinitis, central serous chorioretinopathy and diabetic retinopathy.Results: It was shown that the system can achieve a sensitivity of 73 % and specificity of 72 %.Conclusion: Automated detection of macular lesions using proposed software can significantly reduce manual grading workflow. In addition, automated detection of retinal lesions can be implemented as a clinical decision support system for telemedicine screening. It is anticipated that further development of this technology can become a part of diagnostic image analysis system for the electronic health records.

Impact of technology on cytology outcome in cervical cancer screening of young and older women.

Science.gov (United States)

Rask, J; Lynge, E; Franzmann, M; Hansen, B; Hjortebjerg, A; Rygaard, C; Schledermann, D; Wåhlin, A; Rebolj, M

2014-05-01

Little is known about age-dependent variation in outcomes of cervical cytology with modern technologies. This population-based study evaluated age-dependent changes after routine implementation of ThinPrep and SurePath technology in two independent laboratories, and controlled for time trends in a third laboratory using manually read conventional cytology continually. Data were collected from the Danish National Health Care Registers. For each laboratory, we compared proportions of abnormal cytology defined as atypical squamous cells of undetermined significance or worse (ASCUS+) by age and technology phase. The study included 489,960 cytological samples with no recent abnormality from women aged 23-59 years, routinely screened between 1998 and 2007. Implementation of SurePath liquid-based cytology (LBC) was followed by an increase in abnormal cytology in women aged 23-29 years from 4.6 to 6.1%, relative proportion (RP): 1.31 [95% confidence interval (CI): 1.08-1.61], and a decrease in women aged 45-59 years from 2.9 to 2.0%, RP: 0.71 (95% CI: 0.60-0.83). Implementation of ThinPrep LBC was followed by a decrease in abnormal cytology both in women aged 23-29 years from 7.7 to 6.8%, RP: 0.89 (95% CI: 0.78-1.02) and in women aged 45-59 years from 3.4 to 1.0%, RP: 0.30 (95% CI: 0.24-0.37). With implementation of imaging-assisted reading, regardless of the brand of technology, the proportion of abnormality increased by around 30% in all age groups (range from 19 to 41%). In the laboratory with unchanged technology no trends in abnormality proportions were observed. The impact of LBC implementation on cytological abnormality proportions varied considerably across age groups. © 2013 UICC.

Digital Data Matrix Scanner Developnent At Marshall Space Flight Center

Science.gov (United States)

2004-01-01

Research at NASA's Marshall Space Flight Center has resulted in a system for reading hidden identification codes using a hand-held magnetic scanner. It's an invention that could help businesses improve inventory management, enhance safety, improve security, and aid in recall efforts if defects are discovered. Two-dimensional Data Matrix symbols consisting of letters and numbers permanently etched on items for identification and resembling a small checkerboard pattern are more efficient and reliable than traditional bar codes, and can store up to 100 times more information. A team led by Fred Schramm of the Marshall Center's Technology Transfer Department, in partnership with PRI,Torrance, California, has developed a hand-held device that can read this special type of coded symbols, even if covered by up to six layers of paint. Before this new technology was available, matrix symbols were read with optical scanners, and only if the codes were visible. This latest improvement in digital Data Matrix technologies offers greater flexibility for businesses and industries already using the marking system. Paint, inks, and pastes containing magnetic properties are applied in matrix symbol patterns to objects with two-dimensional codes, and the codes are read by a magnetic scanner, even after being covered with paint or other coatings. The ability to read hidden matrix symbols promises a wide range of benefits in a number of fields, including airlines, electronics, healthcare, and the automotive industry. Many industries would like to hide information on a part, so it can be read only by the party who put it there. For instance, the automotive industry uses direct parts marking for inventory control, but for aesthetic purposes the marks often need to be invisible. Symbols have been applied to a variety of materials, including metal, plastic, glass, paper, fabric and foam, on everything from electronic parts to pharmaceuticals to livestock. The portability of the hand

Highly sensitive bacterial susceptibility test against penicillin using parylene-matrix chip.

Science.gov (United States)

Park, Jong-Min; Kim, Jo-Il; Song, Hyun-Woo; Noh, Joo-Yoon; Kang, Min-Jung; Pyun, Jae-Chul

2015-09-15

This work presented a highly sensitive bacterial antibiotic susceptibility test through β-lactamase assay using Parylene-matrix chip. β-lactamases (EC 3.5.2.6) are an important family of enzymes that confer resistance to β-lactam antibiotics by catalyzing the hydrolysis of these antibiotics. Here we present a highly sensitive assay to quantitate β-lactamase-mediated hydrolysis of penicillin into penicilloic acid. Typically, MALDI-TOF mass spectrometry has been used to quantitate low molecular weight analytes and to discriminate them from noise peaks of matrix fragments that occur at low m/z ratios (m/ztest was carried out using Parylene-matrix chip and MALDI-TOF mass spectrometry. The Parylene-matrix chip was successfully used to quantitate penicillin (m/z: [PEN+H](+)=335.1 and [PEN+Na](+)=357.8) and penicilloic acid (m/z: [PA+H](+)=353.1) in a β-lactamase assay with minimal interference of low molecular weight noise peaks. The β-lactamase assay was carried out with an antibiotic-resistant E. coli strain and an antibiotic-susceptible E. coli strain, revealing that the minimum number of E. coli cells required to screen for antibiotic resistance was 1000 cells for the MALDI-TOF mass spectrometry/Parylene-matrix chip assay. Copyright © 2015 Elsevier B.V. All rights reserved.

Radiation risk from CT: implications for cancer screening.

Science.gov (United States)

Albert, Jeffrey M

2013-07-01

The cancer risks associated with patient exposure to radiation from medical imaging have become a major topic of debate. The higher doses necessary for technologies such as CT and the increasing utilization of these technologies further increase medical radiation exposure to the population. Furthermore, the use of CT for population-based cancer screening continues to be explored for common malignancies such as lung cancer and colorectal cancer. Given the known carcinogenic effects of ionizing radiation, this warrants evaluation of the balance between the benefit of early cancer detection and the risk of screening-induced malignancy. This report provides a brief review of the process of radiation carcino-genesis and the literature evaluating the risk of malignancy from CT, with a focus on the risks and benefits of CT for cancer screening. The available data suggest a small but real risk of radiation-induced malignancy from CT that could become significant at the population level with widespread use of CT-based screening. However, a growing body of literature suggests that the benefits of CT screening for lung cancer in high-risk patients and CT colonography for colorectal cancer may significantly outweigh the radiation risk. Future studies evaluating the benefits of CT screening should continue to consider potential radiation risks.

Applying transpose matrix on advanced encryption standard (AES) for database content

Science.gov (United States)

Manurung, E. B. P.; Sitompul, O. S.; Suherman

2018-03-01

Advanced Encryption Standard (AES) is a specification for the encryption of electronic data established by the U.S. National Institute of Standards and Technology (NIST) and has been adopted by the U.S. government and is now used worldwide. This paper reports the impact of transpose matrix integration to AES. Transpose matrix implementation on AES is aimed at first stage of chypertext modifications for text based database security so that the confidentiality improves. The matrix is also able to increase the avalanche effect of the cryptography algorithm 4% in average.

Intelligent Screening Systems for Cervical Cancer

Directory of Open Access Journals (Sweden)

Yessi Jusman

2014-01-01

Full Text Available Advent of medical image digitalization leads to image processing and computer-aided diagnosis systems in numerous clinical applications. These technologies could be used to automatically diagnose patient or serve as second opinion to pathologists. This paper briefly reviews cervical screening techniques, advantages, and disadvantages. The digital data of the screening techniques are used as data for the computer screening system as replaced in the expert analysis. Four stages of the computer system are enhancement, features extraction, feature selection, and classification reviewed in detail. The computer system based on cytology data and electromagnetic spectra data achieved better accuracy than other data.

High throughput miniature drug-screening platform using bioprinting technology

International Nuclear Information System (INIS)

Rodríguez-Dévora, Jorge I; Reyna, Daniel; Xu Tao; Zhang Bimeng; Shi Zhidong

2012-01-01

In the pharmaceutical industry, new drugs are tested to find appropriate compounds for therapeutic purposes for contemporary diseases. Unfortunately, novel compounds emerge at expensive prices and current target evaluation processes have limited throughput, thus leading to an increase of cost and time for drug development. This work shows the development of the novel inkjet-based deposition method for assembling a miniature drug-screening platform, which can realistically and inexpensively evaluate biochemical reactions in a picoliter-scale volume at a high speed rate. As proof of concept, applying a modified Hewlett Packard model 5360 compact disc printer, green fluorescent protein expressing Escherichia coli cells along with alginate gel solution have been arrayed on a coverslip chip under a repeatable volume of 180% ± 26% picoliters per droplet; subsequently, different antibiotic droplets were patterned on the spots of cells to evaluate the inhibition of bacteria for antibiotic screening. The proposed platform was compared to the current screening process, validating its effectiveness. The viability and basic function of the printed cells were evaluated, resulting in cell viability above 98% and insignificant or no DNA damage to human kidney cells transfected. Based on the reduction of investment and compound volume used by this platform, this technique has the potential to improve the actual drug discovery process at its target evaluation stage. (paper)

Detection and identification of occult HBV in blood donors in Taiwan using a commercial, multiplex, multi-dye nucleic acid amplification technology screening test.

Science.gov (United States)

Lin, K T; Chang, C L; Tsai, M H; Lin, K S; Saldanha, J; Hung, C M

2014-02-01

The ability of a new generation commercial, multiplex, multi-dye test from Roche, the cobas TaqScreen MPX test, version 2.0, to detect and identify occult HBV infections was evaluated using routine donor samples from Kaohsiung Blood Bank, Taiwan. A total of 5973 samples were tested by nucleic acid amplification technology (NAT); 5898 in pools of six, 66 in pools of less than six and nine samples individually. NAT-reactive samples were retested with alternative NAT tests, and follow-up samples from the donors were tested individually by NAT and for all the HBV serological markers. Eight NAT-only-reactive donors were identified, and follow-up samples were obtained from six of the donors. The results indicated that all eight donors had an occult HBV infection with viral loads <12 IU/ml. The cobas(®) TaqScreen MPX test, version 2.0, has an advantage over the current Roche blood screening test, the cobas TaqScreen MPX test, for screening donations in countries with a high prevalence of occult HBV infections since the uncertainty associated with identifying samples with very low viremia is removed by the ability of the test to identify the viral target in samples that are reactive with the cobas TaqScreen MPX test, version 2.0. © 2013 International Society of Blood Transfusion.

Supplemental Immobilization of Hanford Low-Activity Waste: Cast Stone Augmented Formulation Matrix Tests

International Nuclear Information System (INIS)

Cozzi, A.; Crawford, C.; Fox, K.; Hansen, E.; Roberts, K.

2015-01-01

Screening Matrix tests. A set of Cast Stone formulations were devised to augment the original screening test matrix and focus on the range of the test conditions. Fly ash and blast furnace slag were limited to either northwest or southeast and the salt solutions were narrowed to the Average and the SST Blend at the 7.8M Na concentration. To fill in the matrix, a mix ratio of 0.5 was added. In addition, two admixtures, Xypex Admix C-500 and Rheomac SF100 (silica fume), were added as an additional dry material binder in select compositions. As in the Screening Matrix, both fresh and cured properties were evaluated for the formulations. In this study, properties that were influenced by the W/DM ratio in the Screening Matrix; flow diameter, plastic viscosity, density, and compressive strength, showed consistent behavior with respect to W/DM. The leach index for highly soluble components, sodium and nitrate, were not influenced by changes in formulation or the admixtures. The leach index for both iodine and Tc-99 show an influence from the addition of the admixture, Xypex Admix C-500. Additional testing should be performed to further evaluate the influence of Xypex Admix C-500 on the leach index over a range of admixture concentrations, Cast Stone formulations, and curing and storage conditions.

Supplemental Immobilization of Hanford Low-Activity Waste: Cast Stone Augmented Formulation Matrix Tests

Energy Technology Data Exchange (ETDEWEB)

Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fox, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hansen, E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Roberts, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-07-20

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy’s (DOE’s) Hanford Site in Washington State. The HLW will be vitrified in the HLW facility for ultimate disposal at an offsite federal repository. A portion (~35%) of the LAW will be vitrified in the LAW vitrification facility for disposal onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize all of the wastes destined for those facilities. However, a second facility will be needed for the expected volume of LAW requiring immobilization. Cast Stone, a cementitious waste form, is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with the waste acceptance criteria for the disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. A testing program was developed in fiscal year (FY) 2012 describing in detail the work needed to develop and qualify Cast Stone as a waste form for the solidification of Hanford LAW. A statistically designed test matrix was used to evaluate the effects of key parameters on the properties of the Cast Stone as it is initially prepared and after curing. For the processing properties, the water-to-dry-blend mix ratio was the most significant parameter in affecting the range of values observed for each property. The single shell tank (SST) Blend simulant also showed differences in measured properties compared to the other three simulants tested. A review of the testing matrix and results indicated that an additional set of tests would be beneficial to improve the understanding of the impacts noted in the Screening

Corn stalk as matrix in decomposting toilet for treating urine and feces

Science.gov (United States)

Sintawardani, N.; Nilawati, D.; Astuti, J. T.

2017-03-01

Bio-Toilet technology (BT) which is appropriate for the habits of Indonesian people has been studied and developed. BT is a dry toilet technology commonly uses ligno-cellulosic waste materials as matrix to facilitate the growth of natural microbes. In aerobic condition, microbes degrade feces and urine. Mineral as the leftover of feces and urine, such as nitrogen (N), phosphorus (P), and potassium (K) remain in the rest of matrix waste. After certain period. matrix can be harvested and used as soil conditioner. BT uses much less water, mobile, and very useful to be applied in areas where water availability is limited. BT type with different capacities, user amounts and mixing systems has been developed using sawdust for matrix. Since corn stalk is categorized as useless and priceless waste, its application in BT is challenging. Performance of BT with corn stalk as matrix to degrade feces and urine of carnivore imitating the human waste was observed. BT M-15 manual mixing type with paddle was filled with chopped corn stalk as much as 45% of total volume. This BT was designed for 15 person as users per day if 80% reactor volume was filled with ligno-cellulosic matrix. It is assumed that 150 g of feces are discharged once per person/day and 1000 mL of urine 6-8 times per day. Start up process was made in the beginning to initialize the needed microbes in the reactor (matrix). The discharge of feces and urine were increased slowly and gradually the users were increased from 1 to 4 users per day. Performance of BT was indicated by the change in the pile that showed by moisture content, temperature and pH. C/N ratio in matrix decreased significantly from 43 to 17. This result showed that the corn stalk could be used as matrix in BT.

A Threat to Childhood Innocence or the Future of Learning? Parents' Perspectives on the Use of Touch-Screen Technology by 0-3 Year-Olds in the UK

Science.gov (United States)

O'Connor, Jane; Fotakopoulou, Olga

2016-01-01

The rise in personal ownership of touch-screen technology such as iPads and smartphones in the UK in recent years has led to the increasing use of such technology by babies and very young children. This article explores this practice via an online parental survey with 226 UK parents of children aged 0-3 years within the context of the current…

Textile Concentric Ring Electrodes for ECG Recording Based on Screen-Printing Technology

Directory of Open Access Journals (Sweden)

José Vicente Lidón-Roger

2018-01-01

Full Text Available Among many of the electrode designs used in electrocardiography (ECG, concentric ring electrodes (CREs are one of the most promising due to their enhanced spatial resolution. Their development has undergone a great push due to their use in recent years; however, they are not yet widely used in clinical practice. CRE implementation in textiles will lead to a low cost, flexible, comfortable, and robust electrode capable of detecting high spatial resolution ECG signals. A textile CRE set has been designed and developed using screen-printing technology. This is a mature technology in the textile industry and, therefore, does not require heavy investments. Inks employed as conductive elements have been silver and a conducting polymer (poly (3,4-ethylenedioxythiophene polystyrene sulfonate; PEDOT:PSS. Conducting polymers have biocompatibility advantages, they can be used with flexible substrates, and they are available for several printing technologies. CREs implemented with both inks have been compared by analyzing their electric features and their performance in detecting ECG signals. The results reveal that silver CREs present a higher average thickness and slightly lower skin-electrode impedance than PEDOT:PSS CREs. As for ECG recordings with subjects at rest, both CREs allowed the uptake of bipolar concentric ECG signals (BC-ECG with signal-to-noise ratios similar to that of conventional ECG recordings. Regarding the saturation and alterations of ECGs captured with textile CREs caused by intentional subject movements, silver CREs presented a more stable response (fewer saturations and alterations than those of PEDOT:PSS. Moreover, BC-ECG signals provided higher spatial resolution compared to conventional ECG. This improved spatial resolution was manifested in the identification of P1 and P2 waves of atrial activity in most of the BC-ECG signals. It can be concluded that textile silver CREs are more suitable than those of PEDOT:PSS for obtaining

Textile Concentric Ring Electrodes for ECG Recording Based on Screen-Printing Technology.

Science.gov (United States)

Lidón-Roger, José Vicente; Prats-Boluda, Gema; Ye-Lin, Yiyao; Garcia-Casado, Javier; Garcia-Breijo, Eduardo

2018-01-21

Among many of the electrode designs used in electrocardiography (ECG), concentric ring electrodes (CREs) are one of the most promising due to their enhanced spatial resolution. Their development has undergone a great push due to their use in recent years; however, they are not yet widely used in clinical practice. CRE implementation in textiles will lead to a low cost, flexible, comfortable, and robust electrode capable of detecting high spatial resolution ECG signals. A textile CRE set has been designed and developed using screen-printing technology. This is a mature technology in the textile industry and, therefore, does not require heavy investments. Inks employed as conductive elements have been silver and a conducting polymer (poly (3,4-ethylenedioxythiophene) polystyrene sulfonate; PEDOT:PSS). Conducting polymers have biocompatibility advantages, they can be used with flexible substrates, and they are available for several printing technologies. CREs implemented with both inks have been compared by analyzing their electric features and their performance in detecting ECG signals. The results reveal that silver CREs present a higher average thickness and slightly lower skin-electrode impedance than PEDOT:PSS CREs. As for ECG recordings with subjects at rest, both CREs allowed the uptake of bipolar concentric ECG signals (BC-ECG) with signal-to-noise ratios similar to that of conventional ECG recordings. Regarding the saturation and alterations of ECGs captured with textile CREs caused by intentional subject movements, silver CREs presented a more stable response (fewer saturations and alterations) than those of PEDOT:PSS. Moreover, BC-ECG signals provided higher spatial resolution compared to conventional ECG. This improved spatial resolution was manifested in the identification of P1 and P2 waves of atrial activity in most of the BC-ECG signals. It can be concluded that textile silver CREs are more suitable than those of PEDOT:PSS for obtaining BC-ECG records

Consumer preferences for teledermoscopy screening to detect melanoma early.

Science.gov (United States)

Spinks, Jean; Janda, Monika; Soyer, H Peter; Whitty, Jennifer A

2016-01-01

'Store and forward' teledermoscopy is a technology with potential advantages for melanoma screening. Any large-scale implementation of this technology is dependent on consumer acceptance. To investigate preferences for melanoma screening options compared with skin self-examination in adults considered to be at increased risk of developing skin cancer. A discrete choice experiment was completed by 35 consumers, all of whom had prior experience with the use of teledermoscopy, in Queensland, Australia. Participants made 12 choices between screening alternatives described by seven attributes including monetary cost. A mixed logit model was used to estimate the relative weights that consumers place on different aspects of screening, along with the marginal willingness to pay for teledermoscopy as opposed to screening at a clinic. Overall, participants preferred screening/diagnosis by a health professional rather than skin self-examination. Key drivers of screening choice were for results to be reviewed by a dermatologist; a higher detection rate; fewer non-cancerous moles being removed in relation to every skin cancer detected; and less time spent away from usual activities. On average, participants were willing to pay AUD110 to have teledermoscopy with dermatologist review available to them as a screening option. Consumers preferentially value aspects of care that are more feasible with a teledermoscopy screening model, as compared with other skin cancer screening and diagnosis options. This study adds to previous literature in the area which has relied on the use of consumer satisfaction scales to assess the acceptability of teledermoscopy. © The Author(s) 2015.

Perceptions and Practice: The Relationship between Teacher Perceptions of Technology Use and Level of Classroom Technology Integration

Science.gov (United States)

Sawyer, Laura M.

2017-01-01

This correlational-predictive study investigated the relationship between teacher perceptions of technology use and observed classroom technology integration level using the "Technology Uses and Perceptions Survey" (TUPS) and the "Technology Integration Matrix-Observation" (TIM-O) instruments, developed by the Florida Center…

New Technologies in Screening for Disease Risk: Implications for the Worksite and for Health Education.

Science.gov (United States)

McLeroy, Kenneth R.

The screening of workers for health problems has been ubiquitous in the worksite for many years. These screening procedures may have ethical and policy implications. Three common types of screening in use include pre-employment, early identification of health problems, and employee monitoring. Pre-employment screening may be used to screen out…

The Benefits of Single-Touch Screens in Intersubjective Meaning Making

OpenAIRE

Davidsen, Jacob; Christiansen, Ellen Tove

2013-01-01

What are the benefits of single-touch screens? The paper presents findings of onevideo extract from ten months of observation of single-touch screen interaction among 8-9 year-old children. Recent studies of collaborative learning mediated by digital touch screens and tabletops emphasize the possibilities for equal levels of verbal and physical participation.Additionally, these studies suggest that multi-touch technologies offer more task-oriented activities compared to single-touch screen in...

High-Throughput and Rapid Screening of Low-Mass Hazardous Compounds in Complex Samples.

Science.gov (United States)

Wang, Jing; Liu, Qian; Gao, Yan; Wang, Yawei; Guo, Liangqia; Jiang, Guibin

2015-07-07

Rapid screening and identification of hazardous chemicals in complex samples is of extreme importance for public safety and environmental health studies. In this work, we report a new method for high-throughput, sensitive, and rapid screening of low-mass hazardous compounds in complex media without complicated sample preparation procedures. This method is achieved based on size-selective enrichment on ordered mesoporous carbon followed by matrix-assisted laser desorption/ionization-time-of-flight mass spectrometry analysis with graphene as a matrix. The ordered mesoporous carbon CMK-8 can exclude interferences from large molecules in complex samples (e.g., human serum, urine, and environmental water samples) and efficiently enrich a wide variety of low-mass hazardous compounds. The method can work at very low concentrations down to part per trillion (ppt) levels, and it is much faster and more facile than conventional methods. It was successfully applied to rapidly screen and identify unknown toxic substances such as perfluorochemicals in human serum samples from athletes and workers. Therefore, this method not only can sensitively detect target compounds but also can identify unknown hazardous compounds in complex media.

Impact of foamed matrix components on foamed concrete properties

Science.gov (United States)

Tarasenko, V. N.

2018-03-01

The improvement of the matrix foam structure by means of foam stabilizing additives is aimed at solving the technology-oriented problems as well as at the further improvement of physical and mechanical properties of cellular-concrete composites. The dry foam mineralization is the mainstream of this research. Adding the concrete densifiers, foam stabilizers and mineral powders reduces the drying shrinkage, which makes the foam concrete products technologically effective.

Development of a first-principles code based on the screened KKR method for large super-cells

International Nuclear Information System (INIS)

Doi, S; Ogura, M; Akai, H

2013-01-01

The procedures of performing first-principles electronic structure calculation using the Korringa-Kohn-Rostoker (KKR) and the screened KKR methods are reviewed with an emphasis put on their numerical efficiency. It is shown that an iterative matrix inversion combined with a suitable preconditioning greatly improves the computational time of screened KKR method. The method is well parallelized and also has an O(N) scaling property

A Morpholino-based screen to identify novel genes involved in craniofacial morphogenesis

Science.gov (United States)

Melvin, Vida Senkus; Feng, Weiguo; Hernandez-Lagunas, Laura; Artinger, Kristin Bruk; Williams, Trevor

2014-01-01

BACKGROUND The regulatory mechanisms underpinning facial development are conserved between diverse species. Therefore, results from model systems provide insight into the genetic causes of human craniofacial defects. Previously, we generated a comprehensive dataset examining gene expression during development and fusion of the mouse facial prominences. Here, we used this resource to identify genes that have dynamic expression patterns in the facial prominences, but for which only limited information exists concerning developmental function. RESULTS This set of ~80 genes was used for a high throughput functional analysis in the zebrafish system using Morpholino gene knockdown technology. This screen revealed three classes of cranial cartilage phenotypes depending upon whether knockdown of the gene affected the neurocranium, viscerocranium, or both. The targeted genes that produced consistent phenotypes encoded proteins linked to transcription (meis1, meis2a, tshz2, vgll4l), signaling (pkdcc, vlk, macc1, wu:fb16h09), and extracellular matrix function (smoc2). The majority of these phenotypes were not altered by reduction of p53 levels, demonstrating that both p53 dependent and independent mechanisms were involved in the craniofacial abnormalities. CONCLUSIONS This Morpholino-based screen highlights new genes involved in development of the zebrafish craniofacial skeleton with wider relevance to formation of the face in other species, particularly mouse and human. PMID:23559552

Using lessons from breast, cervical, and colorectal cancer screening to inform the development of lung cancer screening programs.

Science.gov (United States)

Armstrong, Katrina; Kim, Jane J; Halm, Ethan A; Ballard, Rachel M; Schnall, Mitchell D

2016-05-01

Multiple advisory groups now recommend that high-risk smokers be screened for lung cancer by low-dose computed tomography. Given that the development of lung cancer screening programs will face many of the same issues that have challenged other cancer screening programs, the National Cancer Institute-funded Population-based Research Optimizing Screening through Personalized Regimens (PROSPR) consortium was used to identify lessons learned from the implementation of breast, cervical, and colorectal cancer screening that should inform the introduction of lung cancer screening. These lessons include the importance of developing systems for identifying and recruiting eligible individuals in primary care, ensuring that screening centers are qualified and performance is monitored, creating clear communication standards for reporting screening results to referring physicians and patients, ensuring follow-up is available for individuals with abnormal test results, avoiding overscreening, remembering primary prevention, and leveraging advances in cancer genetics and immunology. Overall, this experience emphasizes that effective cancer screening is a multistep activity that requires robust strategies to initiate, report, follow up, and track each step as well as a dynamic and ongoing oversight process to revise current screening practices as new evidence regarding screening is created, new screening technologies are developed, new biological markers are identified, and new approaches to health care delivery are disseminated. Cancer 2016;122:1338-1342. © 2016 American Cancer Society. © 2016 American Cancer Society.

In vitro evaluation of matrix metalloproteinases as predictive testing for nickel, a model sensitizing agent

International Nuclear Information System (INIS)

Lamberti, Monica; Perfetto, Brunella; Costabile, Teresa; Canozo, Nunzia; Baroni, Adone; Liotti, Francesco; Sannolo, Nicola; Giuliano, Mariateresa

2004-01-01

The identification of potential damage due to chemical exposure in the workplace is a major health and regulatory concern. Traditional tests that measure both sensitization and elicitation responses require the use of animals. An alternative to this widespread use of experimental animals could have a crucial impact on risk assessment, especially for the preliminary screening of new molecules. We developed an in vitro model for the screening of potential toxic compounds. Human keratinocytes (HaCat) were used as target cells while matrix metalloproteinases (MMP) were selected as responders because they are key enzymes involved in extracellular matrix (ECM) degradation in physiological and pathological conditions. Chemical exposure was performed using nickel sulphate as a positive tester. Nickel contact induced upregulation of MMP-2 and IL-8 mRNA production. Molecular activation occurred even at very low nickel concentrations even though no phenotypic changes were observed. MMP-9 accumulation was found in the medium of treated cells with respect to controls. These observations led to the hypothesis that even minimal exposure can accumulate transcriptional activity resulting in long-term clinical signs after contact. Our simple in vitro model can be applied as a useful preliminary complement to the animal studies to screen the effects of new potential toxic compounds

Icons and Emoticons: Screen Wars

OpenAIRE

Duerfahrd, Lance

2015-01-01

The cinema is being upstaged by a device paradoxically meant (in part) to transmit it: the iPhone. How do films change, how is their impact altered, when viewed on these devices? What aspects of the movie screen (and subsequently our movie experience) are lost or threatened when they are displaced by this new technological format? This is not an abstract war: it is going on (in the dark) every time we attend a screening. My paper will explore what is at stake in our decision to illuminate our...

Low Cost Technology for Screening Early Cancerous Lesions of ...

African Journals Online (AJOL)

hanumantp

[1] The detection rate for early cancerous lesions improved. 60% by unaided visual ... no agreement as how to screen and where to refer patients with oral cancer for ... External and internal examination of the oral cavity was done by the dentist ...

Cellular adhesome screen identifies critical modulators of focal adhesion dynamics, cellular traction forces and cell migration behaviour

Science.gov (United States)

Fokkelman, Michiel; Balcıoğlu, Hayri E.; Klip, Janna E.; Yan, Kuan; Verbeek, Fons J.; Danen, Erik H. J.; van de Water, Bob

2016-01-01

Cancer cells migrate from the primary tumour into surrounding tissue in order to form metastasis. Cell migration is a highly complex process, which requires continuous remodelling and re-organization of the cytoskeleton and cell-matrix adhesions. Here, we aimed to identify genes controlling aspects of tumour cell migration, including the dynamic organization of cell-matrix adhesions and cellular traction forces. In a siRNA screen targeting most cell adhesion-related genes we identified 200+ genes that regulate size and/or dynamics of cell-matrix adhesions in MCF7 breast cancer cells. In a subsequent secondary screen, the 64 most effective genes were evaluated for growth factor-induced cell migration and validated by tertiary RNAi pool deconvolution experiments. Four validated hits showed significantly enlarged adhesions accompanied by reduced cell migration upon siRNA-mediated knockdown. Furthermore, loss of PPP1R12B, HIPK3 or RAC2 caused cells to exert higher traction forces, as determined by traction force microscopy with elastomeric micropillar post arrays, and led to considerably reduced force turnover. Altogether, we identified genes that co-regulate cell-matrix adhesion dynamics and traction force turnover, thereby modulating overall motility behaviour. PMID:27531518

The model for the strategic management of technology. The improvement cycle and matrixes deployment QFD; Un modelo para gestion estrategica de los recursos tecnologicos. El ciclo de mejora y despliegue de matrices QFD

Energy Technology Data Exchange (ETDEWEB)

Benavides Velasco, C. A.; Quintana Garcia, C.

2007-07-01

In spite of the importance of innovative firms, few contributions study in depth the strategic management of their technological resources. After describing the process of strategic management of technology, we propose a model that enables the application of that process and guarantees organizational flexibility in technological companies. For it, such a process has been adapted to She wart cycle (Deeming wheel) and combined with the quality function deployment (QFD). As a result, we propose the improvement cycle of technology. It contains two matrixes that allow identifying and prioritizing with greater clarity the activities related to the management of technological resources. (Authors)

20180311 - High Throughput Transcriptomics: From screening to pathways (SOT 2018)

Science.gov (United States)

The EPA ToxCast effort has screened thousands of chemicals across hundreds of high-throughput in vitro screening assays. The project is now leveraging high-throughput transcriptomic (HTTr) technologies to substantially expand its coverage of biological pathways. The first HTTr sc...

Screening Tools for Kindergarten Children

Directory of Open Access Journals (Sweden)

Georgia Kokkalia

2017-12-01

Full Text Available The current paper review gives a brief and representative description of some of the most used screening tools for kindergarten education. The significant role that early education plays in every child’s academic life is underlined by the importance of tools that give his learning profiles.  Therefore many researchers note that screening tools paly a notable role for the kindergarten teachers, the family and of course for the child in order to offer the appropriate intervention program, the proper support and draw the most suitable teaching method for the child and the class. Thus, the research team of this paper gives the description of some screening tools that are used by kindergarten teachers and specialist’s worldwide-with focus in Greek kindergarten- scoping to underlie strengths and weaknesses of preschoolers. Finally, it is thought worthwhile to say that the screening tools that are presented are used with the traditional way while some of them with the support of new technology.

Efficient computation method of Jacobian matrix

International Nuclear Information System (INIS)

Sasaki, Shinobu

1995-05-01

As well known, the elements of the Jacobian matrix are complex trigonometric functions of the joint angles, resulting in a matrix of staggering complexity when we write it all out in one place. This article addresses that difficulties to this subject are overcome by using velocity representation. The main point is that its recursive algorithm and computer algebra technologies allow us to derive analytical formulation with no human intervention. Particularly, it is to be noted that as compared to previous results the elements are extremely simplified throughout the effective use of frame transformations. Furthermore, in case of a spherical wrist, it is shown that the present approach is computationally most efficient. Due to such advantages, the proposed method is useful in studying kinematically peculiar properties such as singularity problems. (author)

Cinema Screen Advertising: An Old Technology with New Promise for Consumer Marketing.

Science.gov (United States)

Austin, Bruce A.

Few individuals think of the theatrically exhibited motion picture as supported by advertising like other major forms of mass communications. Cinema screen advertising can be defined as the presentation of individual advertising messages on movie theatre screens in a distinct and discrete fashion. Screenvision ads run prior to the start of each…

Cooled Ceramic Matrix Composite Propulsion Structures Demonstrated

Science.gov (United States)

Jaskowiak, Martha H.; Dickens, Kevin W.

2005-01-01

NASA's Next Generation Launch Technology (NGLT) Program has successfully demonstrated cooled ceramic matrix composite (CMC) technology in a scramjet engine test. This demonstration represented the world s largest cooled nonmetallic matrix composite panel fabricated for a scramjet engine and the first cooled nonmetallic composite to be tested in a scramjet facility. Lightweight, high-temperature, actively cooled structures have been identified as a key technology for enabling reliable and low-cost space access. Tradeoff studies have shown this to be the case for a variety of launch platforms, including rockets and hypersonic cruise vehicles. Actively cooled carbon and CMC structures may meet high-performance goals at significantly lower weight, while improving safety by operating with a higher margin between the design temperature and material upper-use temperature. Studies have shown that using actively cooled CMCs can reduce the weight of the cooled flow-path component from 4.5 to 1.6 lb/sq ft and the weight of the propulsion system s cooled surface area by more than 50 percent. This weight savings enables advanced concepts, increased payload, and increased range. The ability of the cooled CMC flow-path components to operate over 1000 F hotter than the state-of-the-art metallic concept adds system design flexibility to space-access vehicle concepts. Other potential system-level benefits include smaller fuel pumps, lower part count, lower cost, and increased operating margin.

Fiscal 1993 report on technological results. R and D on new forming technology of composite materials (Development of innovative technology for producing members for high efficiency power generation); 1993 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

A forming technology was developed which uses superplasticity of composite materials, i.e., high-functional materials for power generating equipment for example. Activities were conducted in the three areas of (1) ceramic based composite materials, (2) development of metal-based composite forming technology, and (3) comprehensive investigation and adjustment. In (1), with a view to finding a composite forming technology, in which high tenacity materials are obtained by evenly dispersing particles or whiskers as reinforcements in a matrix, a room temperature forming technique using fine particles was exploited, as were a high temperature forming technique using fused bodies and a possibility of manifestation of superplasticity in the prepared composite materials. The materials used were Si{sub 3}N{sub 4} matrix-SiC, Al{sub 2}O{sub 3} matrix-TiC, and glass matrix composite based materials filling ceramics in fine holes of porous glass. In (2), composite forming technologies were examined for such composite materials as Al alloy matrix-SiC particulate-based by a molten metal stirring method, Al alloy matrix-ceramics short fiber-based by a high pressure forging method, Ti alloy matrix-ceramics particulate-based by a mechanical alloying method, and Al alloy matrix-ceramics particulate-based by an alkoxide method/powder metallurgy method. (NEDO)

Depression screening optimization in an academic rural setting.

Science.gov (United States)

Aleem, Sohaib; Torrey, William C; Duncan, Mathew S; Hort, Shoshana J; Mecchella, John N

2015-01-01

Primary care plays a critical role in screening and management of depression. The purpose of this paper is to focus on leveraging the electronic health record (EHR) as well as work flow redesign to improve the efficiency and reliability of the process of depression screening in two adult primary care clinics of a rural academic institution in USA. The authors utilized various process improvement tools from lean six sigma methodology including project charter, swim lane process maps, critical to quality tree, process control charts, fishbone diagrams, frequency impact matrix, mistake proofing and monitoring plan in Define-Measure-Analyze-Improve-Control format. Interventions included change in depression screening tool, optimization of data entry in EHR. EHR data entry optimization; follow up of positive screen, staff training and EHR redesign. Depression screening rate for office-based primary care visits improved from 17.0 percent at baseline to 75.9 percent in the post-intervention control phase (p<0.001). Follow up of positive depression screen with Patient History Questionnaire-9 data collection remained above 90 percent. Duplication of depression screening increased from 0.6 percent initially to 11.7 percent and then decreased to 4.7 percent after optimization of data entry by patients and flow staff. Impact of interventions on clinical outcomes could not be evaluated. Successful implementation, sustainability and revision of a process improvement initiative to facilitate screening, follow up and management of depression in primary care requires accounting for voice of the process (performance metrics), system limitations and voice of the customer (staff and patients) to overcome various system, customer and human resource constraints.

Shrinkage covariance matrix approach based on robust trimmed mean in gene sets detection

Science.gov (United States)

Karjanto, Suryaefiza; Ramli, Norazan Mohamed; Ghani, Nor Azura Md; Aripin, Rasimah; Yusop, Noorezatty Mohd

2015-02-01

Microarray involves of placing an orderly arrangement of thousands of gene sequences in a grid on a suitable surface. The technology has made a novelty discovery since its development and obtained an increasing attention among researchers. The widespread of microarray technology is largely due to its ability to perform simultaneous analysis of thousands of genes in a massively parallel manner in one experiment. Hence, it provides valuable knowledge on gene interaction and function. The microarray data set typically consists of tens of thousands of genes (variables) from just dozens of samples due to various constraints. Therefore, the sample covariance matrix in Hotelling's T2 statistic is not positive definite and become singular, thus it cannot be inverted. In this research, the Hotelling's T2 statistic is combined with a shrinkage approach as an alternative estimation to estimate the covariance matrix to detect significant gene sets. The use of shrinkage covariance matrix overcomes the singularity problem by converting an unbiased to an improved biased estimator of covariance matrix. Robust trimmed mean is integrated into the shrinkage matrix to reduce the influence of outliers and consequently increases its efficiency. The performance of the proposed method is measured using several simulation designs. The results are expected to outperform existing techniques in many tested conditions.

LC-MS (/MS) in clinical toxicology screening methods.

Science.gov (United States)

Viette, Véronique; Hochstrasser, Denis; Fathi, Marc

2012-01-01

Toxicological screening is the analysis of biological samples to detect and identify unknown compounds. The high selectivity and sensitivity of liquid chromatography (LC) coupled to mass spectrometry (MS) or tandem mass spectrometry (MS/MS) technology provide an attractive alternative to the current methods (LC-UV, GC/MS, etc.). For these reasons, an increasing number of applications are being published. This paper is a brief overview of LC-MS(/MS) screening methods developed for clinical toxicology in recent years. Various sample treatments, chromatographic separations and detection by mass spectrometry can be combined to obtain screening methods adapted to the constraints and needs of clinical toxicology laboratories. Currently the techniques are in the hands of specialists, mainly in academic institutions. However, the evolution in technology should allow application of these techniques as a tool in toxicology laboratories, thus allowing a more widespread exploitation of their potential.

Initial screening of thermal desorption for soil remediation

International Nuclear Information System (INIS)

Yezzi, J.J. Jr.; Tafuri, A.N.; Rosenthal, S.; Troxler, W.L.

1994-01-01

Petroleum-contaminated soils--caused by spills, leaks, and accidental discharges--exist at many sites throughout the United States. Thermal desorption technologies which are increasingly being employed to treat these soils, have met soil cleanup criteria for a variety of petroleum products. Currently the United States Environmental Protection Agency is finalizing a technical report entitled Use of Thermal Desorption for Treating Petroleum-Contaminated Soils to assist remedial project managers, site owners, remediation contractors, and equipment vendors in evaluating the use of thermal desorption technologies for petroleum-contaminated soil applications. The report will present a three-level screening method to help a reader predict the success of applying thermal desorption at a specific site. The objective of screening level one is to determine the likelihood of success in a specific application of thermal desorption. It will take into account procedures for collecting and evaluating data on site characteristics, contaminant characteristics, soil characteristics, and regulatory requirements. This level will establish whether or not thermal desorption should be evaluated further for site remediation, whether treatment should occur on-site or off-site, and if on-site is a viable option, what system size will be most cost-effective. The scope of this paper addresses only screening level one which provides a preliminary assessment of the applicability of thermal desorption to a particular site. This topic encompasses worksheets that are an integral part of the ''user friendly'' screening process. Level one screening provides a foundation for the subsequent two levels which follow a similar ''user friendly'' worksheet approach to evaluating thermal desorption technologies and establishing costs for thermal desorption in an overall remediation project

Matrix product operators, matrix product states, and ab initio density matrix renormalization group algorithms

Science.gov (United States)

Chan, Garnet Kin-Lic; Keselman, Anna; Nakatani, Naoki; Li, Zhendong; White, Steven R.

2016-07-01

Current descriptions of the ab initio density matrix renormalization group (DMRG) algorithm use two superficially different languages: an older language of the renormalization group and renormalized operators, and a more recent language of matrix product states and matrix product operators. The same algorithm can appear dramatically different when written in the two different vocabularies. In this work, we carefully describe the translation between the two languages in several contexts. First, we describe how to efficiently implement the ab initio DMRG sweep using a matrix product operator based code, and the equivalence to the original renormalized operator implementation. Next we describe how to implement the general matrix product operator/matrix product state algebra within a pure renormalized operator-based DMRG code. Finally, we discuss two improvements of the ab initio DMRG sweep algorithm motivated by matrix product operator language: Hamiltonian compression, and a sum over operators representation that allows for perfect computational parallelism. The connections and correspondences described here serve to link the future developments with the past and are important in the efficient implementation of continuing advances in ab initio DMRG and related algorithms.

Screening for type 2 diabetes: a short report for the National Screening Committee.

Science.gov (United States)

Waugh, N R; Shyangdan, D; Taylor-Phillips, S; Suri, G; Hall, B

2013-08-01

The prevalence of type 2 diabetes mellitus (T2DM) has been increasing, owing to increases in overweight and obesity, decreasing physical activity and the changing demographic structure of the population. People can develop T2DM without symptoms and up to 20% may be undiagnosed. They may have diabetic complications, such as retinopathy, by the time they are diagnosed, or may suffer a heart attack, without warning. Undiagnosed diabetes can be detected by raised blood glucose levels. The aim of this review was to provide an update for the UK National Screening Committee (NSC) on screening for T2DM. As this review was undertaken to update a previous Health Technology Assessment review published in 2007, and a more recent Scottish Public Health Network review, searches for evidence were restricted from 2009 to end of January 2012, with selected later studies added. The databases searched were MEDLINE, EMBASE, MEDLINE-in-Process & Other Non-Indexed Citations, Science Citation Index and Conference Proceedings Citation Index. The case for screening was considered against the criteria used by the NSC to assess proposed population screening programmes. Population screening for T2DM does not meet all of the NSC criteria. Criterion 12, on optimisation of existing management, has not been met. A report by the National Audit Office (NAO) gives details of shortcomings. Criterion 13 requires evidence from high-quality randomised controlled trials that screening is beneficial. This has not been met. The Ely trial of screening showed no benefit. The ADDITION trial was not a trial of screening, but showed no benefit in cardiovascular outcomes from intensive management in people with screen-detected T2DM. Criterion 18 on staffing and facilities does not appear to have been met, according to the NAO report. Criterion 19 requires that all other options, including prevention, should have been considered. A large proportion of cases of T2DM could be prevented if people avoided becoming

High-throughput screening platform for engineered nanoparticle-mediated genotoxicity using CometChip technology.

Science.gov (United States)

Watson, Christa; Ge, Jing; Cohen, Joel; Pyrgiotakis, Georgios; Engelward, Bevin P; Demokritou, Philip

2014-03-25

The likelihood of intentional and unintentional engineered nanoparticle (ENP) exposure has dramatically increased due to the use of nanoenabled products. Indeed, ENPs have been incorporated in many useful products and have enhanced our way of life. However, there are many unanswered questions about the consequences of nanoparticle exposures, in particular, with regard to their potential to damage the genome and thus potentially promote cancer. In this study, we present a high-throughput screening assay based upon the recently developed CometChip technology, which enables evaluation of single-stranded DNA breaks, abasic sites, and alkali-sensitive sites in cells exposed to ENPs. The strategic microfabricated, 96-well design and automated processing improves efficiency, reduces processing time, and suppresses user bias in comparison to the standard comet assay. We evaluated the versatility of this assay by screening five industrially relevant ENP exposures (SiO2, ZnO, Fe2O3, Ag, and CeO2) on both suspension human lymphoblastoid (TK6) and adherent Chinese hamster ovary (H9T3) cell lines. MTT and CyQuant NF assays were employed to assess cellular viability and proliferation after ENP exposure. Exposure to ENPs at a dose range of 5, 10, and 20 μg/mL induced dose-dependent increases in DNA damage and cytotoxicity. Genotoxicity profiles of ZnO>Ag>Fe2O3>CeO2>SiO2 in TK6 cells at 4 h and Ag>Fe2O3>ZnO>CeO2>SiO2 in H9T3 cells at 24 h were observed. The presented CometChip platform enabled efficient and reliable measurement of ENP-mediated DNA damage, therefore demonstrating the efficacy of this powerful tool in nanogenotoxicity studies.

The converse magnetoelectric coupling in asymmetric granule/matrix composite film with Ni/PZT component

Science.gov (United States)

Chen, Bo; Su, Ning-Ning; Cui, Wen-Li; Yan, Shi-Nong

2018-04-01

In this work, a type of asymmetric granule/matrix composite film is designed, where the Ni granule is dispersed in PZT matrix, meanwhile the top and bottom electrode is constituted by Au and SRO respectively. Predicted through the electrostatic screening model and mean field approximation, considerable electrostatic charge is induced on Ni granule surface by ferroelectric PZT polarization. Predicted through the spin splitting model and spherical shell approximation, both the magnetization and magnetic anisotropy of Ni granule are modulated by ferroelectric PZT polarization. As the volume fraction of Ni granule is increased, the electric modulation of magnetization and magnetic anisotropy is reduced and enhanced respectively. As the dimension of granule/matrix composite is varied, such modulation is retained. Due to the large area-volume ratio of nano-granule, this work benefits to realize the converse magnetoelectric coupling in nanoscale.

In vitro microfluidic models of tumor microenvironment to screen transport of drugs and nanoparticles.

Science.gov (United States)

Ozcelikkale, Altug; Moon, Hye-Ran; Linnes, Michael; Han, Bumsoo

2017-09-01

Advances in nanotechnology have enabled numerous types of nanoparticles (NPs) to improve drug delivery to tumors. While many NP systems have been proposed, their clinical translation has been less than anticipated primarily due to failure of current preclinical evaluation techniques to adequately model the complex interactions between the NP and physiological barriers of tumor microenvironment. This review focuses on microfluidic tumor models for characterization of delivery efficacy and toxicity of cancer nanomedicine. Microfluidics offer significant advantages over traditional macroscale cell cultures by enabling recapitulation of tumor microenvironment through precise control of physiological cues such as hydrostatic pressure, shear stress, oxygen, and nutrient gradients. Microfluidic systems have recently started to be adapted for screening of drugs and NPs under physiologically relevant settings. So far the two primary application areas of microfluidics in this area have been high-throughput screening using traditional culture settings such as single cells or multicellular tumor spheroids, and mimicry of tumor microenvironment for study of cancer-related cell-cell and cell-matrix interactions. These microfluidic technologies are also useful in modeling specific steps in NP delivery to tumor and characterize NP transport properties and outcomes by systematic variation of physiological conditions. Ultimately, it will be possible to design drug-screening platforms uniquely tailored for individual patient physiology using microfluidics. These in vitro models can contribute to development of precision medicine by enabling rapid and patient-specific evaluation of cancer nanomedicine. WIREs Nanomed Nanobiotechnol 2017, 9:e1460. doi: 10.1002/wnan.1460 For further resources related to this article, please visit the WIREs website. © 2017 Wiley Periodicals, Inc.

Visualizing the dental biofilm matrix by means of fluorescence lectin-binding analysis

DEFF Research Database (Denmark)

Tawakoli, Pune Nina; Neu, Thomas R; Busck, Mette Marie

2017-01-01

lectins to visualize and quantify extracellular glycoconjugates in dental biofilms. Lectin binding was screened on pooled supragingival biofilm samples collected from 76 subjects using confocal microscopy. FLBA was then performed with 10 selected lectins on biofilms grown in situ for 48 h in the absence......The extracellular matrix is a poorly studied, yet important component of dental biofilms. Fluorescence lectin-binding analysis (FLBA) is a powerful tool to characterize glycoconjugates in the biofilm matrix. This study aimed to systematically investigate the ability of 75 fluorescently labeled......-biofilms: Aleuria aurantia (AAL), Calystega sepiem (Calsepa), Lycopersicon esculentum (LEA), Morniga-G (MNA-G) and Helix pomatia (HPA). No significant correlation between the binding of specific lectins and bacterial composition was found. Fluorescently labeled lectins enable the visualization of glycoconjugates...

Technology-enabled examinations of cardiac rhythm, optic nerve, oral health, tympanic membrane, gait and coordination evaluated jointly with routine health screenings: an observational study at the 2015 Kumbh Mela in India

Science.gov (United States)

Gupta, Otkrist; Patalano II, Vincent; Mohit, Mrinal; Merchant, Rikin; Subramanian, S V

2018-01-01

Objectives Technology-enabled non-invasive diagnostic screening (TES) using smartphones and other point-of-care medical devices was evaluated in conjunction with conventional routine health screenings for the primary care screening of patients. Design Dental conditions, cardiac ECG arrhythmias, tympanic membrane disorders, blood oxygenation levels, optic nerve disorders and neurological fitness were evaluated using FDA-approved advanced smartphone powered technologies. Routine health screenings were also conducted. A novel remote web platform was developed to allow expert physicians to examine TES data and compare efficacy with routine health screenings. Setting The study was conducted at a primary care centre during the 2015 Kumbh Mela in Maharashtra, India. Participants 494 consenting 18–90 years old adults attending the 2015 Kumbh Mela were tested. Results TES and routine health screenings identified unique clinical conditions in distinct patients. Intraoral fluorescent imaging classified 63.3% of the population with dental caries and periodontal diseases. An association between poor oral health and cardiovascular illnesses was also identified. Tympanic membrane imaging detected eardrum abnormalities in 13.0% of the population, several with a medical history of hearing difficulties. Gait and coordination issues were discovered in eight subjects and one subject had arrhythmia. Cross-correlations were observed between low oxygen saturation and low body mass index (BMI) with smokers (p=0.0087 and p=0.0122, respectively), and high BMI was associated with elevated blood pressure in middle-aged subjects. Conclusions TES synergistically identified clinically significant abnormalities in several subjects who otherwise presented as normal in routine health screenings. Physicians validated TES findings and used routine health screening data and medical history responses for comprehensive diagnoses for at-risk patients. TES identified high prevalence of oral diseases

Ultrasound as an Adjunct to Mammography for Breast Cancer Screening: A Health Technology Assessment

Science.gov (United States)

Nikitovic-Jokic, Milica; Tu, Hong Anh; Palimaka, Stefan; Higgins, Caroline; Holubowich, Corinne

2016-01-01

Background Screening with mammography can detect breast cancer early, before clinical symptoms appear. Some cancers, however, are not captured with mammography screening alone. Ultrasound has been suggested as a safe adjunct screening tool that can detect breast cancers missed on mammography. We investigated the benefits, harms, cost-effectiveness, and cost burden of ultrasound as an adjunct to mammography compared with mammography alone for screening women at average risk and at high risk for breast cancer. Methods We searched Ovid MEDLINE, Ovid Embase, EBM Reviews, and the NHS Economic Evaluation Database, from January 1998 to June 2015, for evidence of effectiveness, harms, diagnostic accuracy, and cost-effectiveness. Only studies evaluating the use of ultrasound as an adjunct to mammography in the specified populations were included. We also conducted a cost analysis to estimate the costs in Ontario over the next 5 years to fund ultrasound as an adjunct to mammography in breast cancer screening for high-risk women who are contraindicated for MRI, the current standard of care to supplement mammography. Results No studies in average-risk women met the inclusion criteria of the clinical review. We included 5 prospective, paired cohort studies in high-risk women, 4 of which were relevant to the Ontario context. Adjunct ultrasound identified between 2.3 and 5.9 additional breast cancers per 1,000 screens. The average pooled sensitivity of mammography and ultrasound was 53%, a statistically significant increase relative to mammography alone (absolute increase 13%; P screening alone. The GRADE for this body of evidence was low. Additional annual costs of using breast ultrasound as an adjunct to mammography for high-risk women in Ontario contraindicated for MRI would range from $15,500 to $30,250 in the next 5 years. Conclusions We found no evidence that evaluated the comparative effectiveness or diagnostic accuracy of screening breast ultrasound as an adjunct to

On the 'Interim summary of requirements and criteria for nationwide scientific screening by the geological disposal technology working group.'

International Nuclear Information System (INIS)

Tochiyama, Osamu

2016-01-01

In order to make progress on the permanent geological disposal of high-level radioactive waste, the government of Japan revised, in May 2015, the basic plan to expand the site selection process, in which a set of site screening criteria was issued based on the existing geoscientific knowledge. These criteria were developed by the Geological Disposal Technology Working Group of the Nuclear Energy Subcommittee which was created by the Ministry of Economy, Trade and Industry (METI). (author)

A novel tandem mass spectrometry method for first-line screening of mainly beta-thalassemia from dried blood spots.

Science.gov (United States)

Yu, Chaowen; Huang, Shuodan; Wang, Ming; Zhang, Juan; Liu, Hao; Yuan, Zhaojian; Wang, Xingbin; He, Xiaoyan; Wang, Jie; Zou, Lin

2017-02-10

Traditional methods for thalassemia screening are time-consuming and easily affected by cell hemolysis or hemoglobin degradation in stored blood samples. Tandem mass spectrometry (MS/MS) proved to be an effective technology for sickle cell disorders (SCD) screening. Here, we developed a novel MS/MS method for β-thalassemia screening from dried blood spots (DBS). Stable isotopic-labeled peptides were used as internal standards for quantification and calculation of the α:β-globin ratios. We used the α:β-globin ratio cutoffs to differentiate between normal individuals and patients with thalassemia. About 781 patients and 300 normal individuals were analyzed. The α:β-globin ratios showed significant difference between normal and β-thalassemia patients (Pthalassemia mutation. In the parallel study, all cases screened for suspected thalassemia from six hundred DBS samples by using this MS/MS method were successfully confirmed by genotyping. The intra-assay and inter-assay CVs of the ratios ranged from 2.4% to 3.9% and 4.7% to 7.1%, and there was no significant sample carryover or matrix effect for this MS/MS method. Combined with SCD screening, this MS/MS method could be used as a first-line screening assay for both structural and expression abnormalities of human hemoglobin. Traditional methods for thalassemia screening were depending on the structural integrity of tetramers and could be affected by hemolysis and degradation of whole blood samples, especially when stored. We used proteospecific peptides produced by the tryptic digestion of each globin to evaluate the production ratio between α- and β-globin chains, which turned out to be quite stable even when stored for more than two months. Though most of the peptides were specific to α-globin or β-globin, we only chose four most informative peptides and its stable isotopic-labeled peptides as internal standards for analysis, which could obtain a high accuracy. Currently, we are the first to address the

Rationale and Study Protocol for a Multi-component Health Information Technology (HIT) Screening Tool for Depression and Post-traumatic Stress Disorder in the Primary Care Setting

Science.gov (United States)

Biegler, Kelly; Mollica, Richard; Sim, Susan Elliott; Nicholas, Elisa; Chandler, Maria; Ngo-Metzger, Quyen; Paigne, Kittya; Paigne, Sompia; Nguyen, Danh V.; Sorkin, Dara H.

2016-01-01

The prevalence rate of depression in primary care is high. Primary care providers serve as the initial point of contact for the majority of patients with depression, yet, approximately 50% of cases remain unrecognized. The under-diagnosis of depression may be further exacerbated in limited English-language proficient (LEP) populations. Language barriers may result in less discussion of patients’ mental health needs and fewer referrals to mental health services, particularly given competing priorities of other medical conditions and providers’ time pressures. Recent advances in Health Information Technology (HIT) may facilitate novel ways to screen for depression in LEP populations. The purpose of this paper is to describe the rationale and protocol of a clustered-randomized controlled trial that will test the effectiveness of an HIT intervention that provides a multi-component approach to delivering culturally competent, mental health care in the primary care setting. The HIT intervention has four components: 1) web-based provider training, 2) multimedia electronic screening of depression and PTSD in the patients’ primary language, 3) Computer generated risk assessment scores delivered directly to the provider, and 4) clinical decision support. The outcomes of the study include assessing the potential of the HIT intervention to improve screening rates, clinical detection, provider initiation of treatment, and patient outcomes for depression and PTSD among LEP Cambodian refugees who experienced war atrocities and trauma during the Khmer Rouge. This technology has the potential to be adapted to any LEP population in order to facilitate mental health screening and treatment in the primary care setting. PMID:27394385

Matrix converter controlled with the direct transfer function approach

DEFF Research Database (Denmark)

Rodriguez, J.; Silva, E.; Blaabjerg, Frede

2005-01-01

Power electronics is an emerging technology. New power circuits are invented and have to be introduced into the power electronics curriculum. One of the interesting new circuits is the matrix converter (MC), and this paper analyses its working principles. A simple model is proposed to represent...

Is the extraction by Whatman FTA filter matrix technology and sequencing of large ribosomal subunit D1-D2 region sufficient for identification of clinical fungi?

Science.gov (United States)

Kiraz, Nuri; Oz, Yasemin; Aslan, Huseyin; Erturan, Zayre; Ener, Beyza; Akdagli, Sevtap Arikan; Muslumanoglu, Hamza; Cetinkaya, Zafer

2015-10-01

Although conventional identification of pathogenic fungi is based on the combination of tests evaluating their morphological and biochemical characteristics, they can fail to identify the less common species or the differentiation of closely related species. In addition these tests are time consuming, labour-intensive and require experienced personnel. We evaluated the feasibility and sufficiency of DNA extraction by Whatman FTA filter matrix technology and DNA sequencing of D1-D2 region of the large ribosomal subunit gene for identification of clinical isolates of 21 yeast and 160 moulds in our clinical mycology laboratory. While the yeast isolates were identified at species level with 100% homology, 102 (63.75%) clinically important mould isolates were identified at species level, 56 (35%) isolates at genus level against fungal sequences existing in DNA databases and two (1.25%) isolates could not be identified. Consequently, Whatman FTA filter matrix technology was a useful method for extraction of fungal DNA; extremely rapid, practical and successful. Sequence analysis strategy of D1-D2 region of the large ribosomal subunit gene was found considerably sufficient in identification to genus level for the most clinical fungi. However, the identification to species level and especially discrimination of closely related species may require additional analysis. © 2015 Blackwell Verlag GmbH.

Neonatal screening for inborn errors of metabolism: cost, yield and outcome.

Science.gov (United States)

Pollitt, R J; Green, A; McCabe, C J; Booth, A; Cooper, N J; Leonard, J V; Nicholl, J; Nicholson, P; Tunaley, J R; Virdi, N K

1997-01-01

OBJECTIVES. To systematically review the literature on inborn errors of metabolism, neonatal screening technology and screening programmes in order to analyse the costs and benefits of introducing screening based on tandem mass-spectrometry (tandem MS) for a wide range of disorders of amino acid and organic acid metabolism in the UK. To evaluate screening for cystic fibrosis, Duchenne muscular dystrophy and other disorders which are tested on an individual basis. HOW THE RESEARCH WAS CONDUCTED. Systematic searches were carried out of the literature on inborn errors of metabolism, neonatal screening programmes, tandem MS-based neonatal screening technology, economic evaluations of neonatal screening programmes and psychological aspects of neonatal screening. Background material on the biology of inherited metabolic disease, the basic philosophy, and the history and current status of the UK screening programme was also collected. Relevant papers in the grey literature and recent publications were identified by hand-searching. Each paper was graded. For each disease an aggregate grade for the state of knowledge in six key areas was awarded. Additional data were prospectively collected on activity and costs in UK neonatal screening laboratories, and expert clinical opinion on current treatment modalities and outcomes. These data were used to construct a decision-analysis model of neonatal screening technologies, comparing tandem MS with the existing phenylketonuria screening methods. This model determined the cost per additional case identified and, for each disease, the additional treatment costs per case, and the cost per life-year saved. All costs and benefits were discounted at 6% per annum. One-way sensitivity analysis was performed showing the effect of varying the discount rate, the incidence rate of each disorder, the number of neonates screened and the cost of tandem MS, on the cost per life-year gained. RESEARCH FINDINGS. The UK screening programmes for

Characteristic analysis on UAV-MIMO channel based on normalized correlation matrix.

Science.gov (United States)

Gao, Xi jun; Chen, Zi li; Hu, Yong Jiang

2014-01-01

Based on the three-dimensional GBSBCM (geometrically based double bounce cylinder model) channel model of MIMO for unmanned aerial vehicle (UAV), the simple form of UAV space-time-frequency channel correlation function which includes the LOS, SPE, and DIF components is presented. By the methods of channel matrix decomposition and coefficient normalization, the analytic formula of UAV-MIMO normalized correlation matrix is deduced. This formula can be used directly to analyze the condition number of UAV-MIMO channel matrix, the channel capacity, and other characteristic parameters. The simulation results show that this channel correlation matrix can be applied to describe the changes of UAV-MIMO channel characteristics under different parameter settings comprehensively. This analysis method provides a theoretical basis for improving the transmission performance of UAV-MIMO channel. The development of MIMO technology shows practical application value in the field of UAV communication.

The extracellular matrix: Structure, composition, age-related differences, tools for analysis and applications for tissue engineering.

Science.gov (United States)

Kular, Jaspreet K; Basu, Shouvik; Sharma, Ram I

2014-01-01

The extracellular matrix is a structural support network made up of diverse proteins, sugars and other components. It influences a wide number of cellular processes including migration, wound healing and differentiation, all of which is of particular interest to researchers in the field of tissue engineering. Understanding the composition and structure of the extracellular matrix will aid in exploring the ways the extracellular matrix can be utilised in tissue engineering applications especially as a scaffold. This review summarises the current knowledge of the composition, structure and functions of the extracellular matrix and introduces the effect of ageing on extracellular matrix remodelling and its contribution to cellular functions. Additionally, the current analytical technologies to study the extracellular matrix and extracellular matrix-related cellular processes are also reviewed.

Newborn Screening for Primary Immunodeficiency Diseases: The Past, the Present and the Future

Directory of Open Access Journals (Sweden)

Jovanka King

2017-08-01

Full Text Available Primary immunodeficiency diseases (PID are a heterogeneous group of disorders caused by inborn errors of immunity, with affected children presenting with severe, recurrent or unusual infections. Over 300 distinct genetic molecular abnormalities resulting in PID have been identified, and this number continues to rise. Newborn screening for PID has been established in many countries, with the majority of centers using a PCR-based T cell receptor excision circle (TREC assay to screen for severe combined immunodeficiency (SCID and other forms of T cell lymphopenia. Multiplexed screening including quantitation of kappa-recombining exclusion circles (KREC has also been described, offering advantages over TREC screening alone. Screening technologies are also expanding to include protein-based assays to identify complement deficiencies and granulocyte disorders. Given the rapid advances in genomic medicine, a potential future direction is the application of next-generation sequencing (NGS technologies to screen infants for a panel of genetic mutations, which would enable identification of a wide range of diseases. However, several ethical and economic issues must be considered before moving towards this screening strategy.

Studies Comparing Screen-Film Mammography and Full-Field Digital Mammography in Breast Cancer Screening: Updated Review

International Nuclear Information System (INIS)

Skaane, P.

2009-01-01

Full-field digital mammography (FFDM) has several potential benefits as compared with screen-film mammography (SFM) in mammography screening. Digital technology also opens for implementation of advanced applications, including computer-aided detection (CAD) and tomosynthesis. Phantom studies and experimental clinical studies have shown that FFDM is equal or slightly superior to SFM for detection and characterization of mammographic abnormalities. Despite obvious advantages, the conversion to digital mammography has been slower than anticipated, and not only due to higher costs. Until very recently, some countries did not even permit the use of digital mammography in breast cancer screening. The reason for this reluctant attitude was concern about lower spatial resolution and about using soft-copy reading. Furthermore, there was a lack of data supporting improved diagnostic accuracy using FFDM in a screening setting, since two pioneer trials both showed nonsignificantly lower cancer detection rate at FFDM. The 10 studies comparing FFDM and SFM in mammography screening published so far have shown divergent and rather conflicting results. Nevertheless, there is a rapid conversion to digital mammography in breast cancer screening in many western countries. The aim of this article is to give an updated review of these studies, discuss the conflicting findings, and draw some conclusions from the results

Radioimmunoassay screening and GC/MS confirmation of whole blood samples for drugs of abuse

Energy Technology Data Exchange (ETDEWEB)

Spiehler, V.R.; Sedgwick, P.

From 1981 to 1984, an average of 300 radioimmunoassay screens on whole blood were performed each week in the authors laboratory. Most samples were screened for opiates phencyclidine and its analogs, barbiturates, and cocaine or its metabolite benzoylecgonine. A commercially available radioimmunoassay was used with modifications to facilitate screening of whole blood. Increasing sample size increased the sensitivity of the assay. Changing reagent concentration (1:1 dilution), incubation time, sample matrix (water, urine, or blood), or fraction counted (precipitate or supernatant) did not affect the utility of the standard curve or the sensitivity of the assay. All positive results for phencyclidine, opiates, cocaine, and related compounds were confirmed by GC/MA. Barbiturate positives were confirmed by UV spectrophotometry.

Steel-SiC Metal Matrix Composite Development. Final report

International Nuclear Information System (INIS)

Smith, Don D.

2005-01-01

One of the key materials challenges for Generation IV reactor technology is to improve the strength and resistance to corrosion and radiation damage in the metal cladding of the fuel pins during high-temperature operation. Various candidate Gen IV designs call for increasing core temperature to improve efficiency and facilitate hydrogen production, operation with molten lead moderator to use fast neutrons. Fuel pin lifetime against swelling and fracture is a significant limit in both respects. The goal of this project is to develop a method for fabricating SiC-reinforced high-strength steel. We are developing a metal-matrix composite (MMC) in which SiC fibers are be embedded within a metal matrix of steel, with adequate interfacial bonding to deliver the full benefit of the tensile strength of the SiC fibers in the composite. In the context of the mission of the SBIR program, this Phase I grant has been successful. The development of a means to attain interfacial bonding between metal and ceramic has been a pacing challenge in materials science and technology for a century. It entails matching or grading of thermal expansion across the interface and attaining a graded chemical composition so that impurities do not concentrate at the boundary to create a slip layer. To date these challenges have been solved in only a modest number of pairings of compatible materials, e.g. Kovar and glass, titanium and ceramic, and aluminum and ceramic. The latter two cases have given rise to the only presently available MMC materials, developed for aerospace applications. Those materials have been possible because the matrix metal is highly reactive at elevated temperature so that graded composition and intimate bonding happens naturally at the fiber-matrix interface. For metals that are not highly reactive at processing temperature, however, successful bonding is much more difficult. Recent success has been made with copper MMCs for cooling channels in first-wall designs for fusion

Knowledge and social engagement change in intention to be screened for colorectal cancer.

Science.gov (United States)

Molina, Yamile; Briant, Katherine J; Sanchez, Janeth I; O'Connell, Mary A; Thompson, Beti

2018-07-01

Innovative technologies have been used to promote colorectal cancer (CRC) screening among the underserved. However, the impact of these innovative technologies on knowledge and social engagement likelihood as they relate to subsequent intention to be screened across different populations has not been fully explored. Using a pre-post-test design with an inflatable walk-through colon, we assessed changes in knowledge and social engagement likelihood across populations and their associations with intention to be screened in two community settings. One was a community setting in Washington State (WA); the other, a college campus in New Mexico (NM). Differential effects on knowledge and social engagement likelihood were examined across demographic groups (race/ethnicity, gender, age, education, insurance status, and geographic region). Finally, we assessed if changes in knowledge and social engagement likelihood were associated with CRC screening intention. NM males had greater gains in CRC knowledge than NM females; in WA, Hispanics, younger, less educated, and uninsured participants had greater gains in knowledge. NM females and younger WA participants were more likely to discuss CRC with their social networks than NM males and older WA participants. In WA, Hispanics and older adults reported greater intention to be screened for CRC. Change in social engagement likelihood, but not knowledge, was associated with intention to be screened. The effectiveness of health promotion technologies on knowledge and social engagement may vary across different demographic characteristics. Further, the importance of social engagement likelihood in interacting with intention to be screened was substantiated.

Ceramic matrix composite article and process of fabricating a ceramic matrix composite article

Science.gov (United States)

Cairo, Ronald Robert; DiMascio, Paul Stephen; Parolini, Jason Robert

2016-01-12

A ceramic matrix composite article and a process of fabricating a ceramic matrix composite are disclosed. The ceramic matrix composite article includes a matrix distribution pattern formed by a manifold and ceramic matrix composite plies laid up on the matrix distribution pattern, includes the manifold, or a combination thereof. The manifold includes one or more matrix distribution channels operably connected to a delivery interface, the delivery interface configured for providing matrix material to one or more of the ceramic matrix composite plies. The process includes providing the manifold, forming the matrix distribution pattern by transporting the matrix material through the manifold, and contacting the ceramic matrix composite plies with the matrix material.

Performance analysis of stationary Hadamard matrix diffusers in free-space optical communication links

Science.gov (United States)

Burrell, Derek J.; Middlebrook, Christopher T.

2017-08-01

Wireless communication systems that employ free-space optical links in place of radio/microwave technologies carry substantial benefits in terms of data throughput, network security and design efficiency. Along with these advantages comes the challenge of counteracting signal degradation caused by atmospheric turbulence in free-space environments. A fully coherent laser source experiences random phase delays along its traversing path in turbulent conditions forming a speckle pattern and lowering the received signal-to-noise ratio upon detection. Preliminary research has shown that receiver-side speckle contrast may be significantly reduced and signal-to-noise ratio increased accordingly through the use of a partially coherent light source. While dynamic diffusers and adaptive optics solutions have been proven effective, they also add expense and complexity to a system that relies on accessibility and robustness for successful implementation. A custom Hadamard diffractive matrix design is used to statically induce partial coherence in a transmitted beam to increase signal-to-noise ratio for experimental turbulence scenarios. Atmospheric phase screens are generated using an open-source software package and subsequently loaded into a spatial light modulator using nematic liquid crystals to modulate the phase.

Hierarchical matrix techniques for the solution of elliptic equations

KAUST Repository

Chávez, Gustavo

2014-05-04

Hierarchical matrix approximations are a promising tool for approximating low-rank matrices given the compactness of their representation and the economy of the operations between them. Integral and differential operators have been the major applications of this technology, but they can be applied into other areas where low-rank properties exist. Such is the case of the Block Cyclic Reduction algorithm, which is used as a direct solver for the constant-coefficient Poisson quation. We explore the variable-coefficient case, also using Block Cyclic reduction, with the addition of Hierarchical Matrices to represent matrix blocks, hence improving the otherwise O(N2) algorithm, into an efficient O(N) algorithm.

Design of a projection display screen with vanishing color shift for rear-projection HDTV

Science.gov (United States)

Liu, Xiu; Zhu, Jin-lin

1996-09-01

Using bi-convex cylinder lens with matrix structure, the transmissive projection display screen with high contrast and wider viewing angle has been widely used in large rear projection TV and video projectors, it obtained a inhere color shift and puzzled the designer of display screen for RGB projection tube in-line adjustment. Based on the method of light beam racing, the general software of designing projection display screen has been developed and the computer model of vanishing color shift for rear projection HDTV has bee completed. This paper discussed the practical designing method to vanish the defect of color shift and mentioned the relations between the primary optical parameters of display screen and relative geometry sizes of lens' surface. The distributions of optical gain to viewing angle and the influences on engineering design are briefly analyzed.

Automated microscopy for high-content RNAi screening

Science.gov (United States)

2010-01-01

Fluorescence microscopy is one of the most powerful tools to investigate complex cellular processes such as cell division, cell motility, or intracellular trafficking. The availability of RNA interference (RNAi) technology and automated microscopy has opened the possibility to perform cellular imaging in functional genomics and other large-scale applications. Although imaging often dramatically increases the content of a screening assay, it poses new challenges to achieve accurate quantitative annotation and therefore needs to be carefully adjusted to the specific needs of individual screening applications. In this review, we discuss principles of assay design, large-scale RNAi, microscope automation, and computational data analysis. We highlight strategies for imaging-based RNAi screening adapted to different library and assay designs. PMID:20176920

Cold Leak Tests of LHC Beam Screens

CERN Document Server

Collomb-Patton, C; Jenninger, B; Kos, N

2009-01-01

In order to guide the high energy proton beams inside its two 27 km long vacuum rings, the Large Hadron Collider (LHC) at CERN, Geneva, makes use of superconducting technology to create the required magnetic fields. More than 4000 beam screens, cooled at 7 20 K, are inserted inside the 1.9 K beam vacuum tubes to intercept beam induced heat loads and to provide dynamic vacuum stability. As extremely high helium leak tightness is required, all beam screens have been leak tested under cold conditions in a dedicated test stand prior to their installation. After describing the beam screen design and its functions, this report focuses on the cold leak test sequence and discusses the results.

Rationale and study protocol for a multi-component Health Information Technology (HIT) screening tool for depression and post-traumatic stress disorder in the primary care setting.

Science.gov (United States)

Biegler, Kelly; Mollica, Richard; Sim, Susan Elliott; Nicholas, Elisa; Chandler, Maria; Ngo-Metzger, Quyen; Paigne, Kittya; Paigne, Sompia; Nguyen, Danh V; Sorkin, Dara H

2016-09-01

The prevalence rate of depression in primary care is high. Primary care providers serve as the initial point of contact for the majority of patients with depression, yet, approximately 50% of cases remain unrecognized. The under-diagnosis of depression may be further exacerbated in limited English-language proficient (LEP) populations. Language barriers may result in less discussion of patients' mental health needs and fewer referrals to mental health services, particularly given competing priorities of other medical conditions and providers' time pressures. Recent advances in Health Information Technology (HIT) may facilitate novel ways to screen for depression and other mental health disorders in LEP populations. The purpose of this paper is to describe the rationale and protocol of a clustered randomized controlled trial that will test the effectiveness of an HIT intervention that provides a multi-component approach to delivering culturally competent, mental health care in the primary care setting. The HIT intervention has four components: 1) web-based provider training, 2) multimedia electronic screening of depression and PTSD in the patients' primary language, 3) Computer generated risk assessment scores delivered directly to the provider, and 4) clinical decision support. The outcomes of the study include assessing the potential of the HIT intervention to improve screening rates, clinical detection, provider initiation of treatment, and patient outcomes for depression and post-traumatic stress disorder (PTSD) among LEP Cambodian refugees who experienced war atrocities and trauma during the Khmer Rouge. This technology has the potential to be adapted to any LEP population in order to facilitate mental health screening and treatment in the primary care setting. Copyright © 2016 Elsevier Inc. All rights reserved.

Cervical cancer screening programs in Latin America and the Caribbean.

Science.gov (United States)

Murillo, Raul; Almonte, Maribel; Pereira, Ana; Ferrer, Elena; Gamboa, Oscar A; Jerónimo, José; Lazcano-Ponce, Eduardo

2008-08-19

Latin America and the Caribbean (LAC) have a significant burden of cervical cancer. Prophylactic human papillomavirus (HPV) vaccines are an opportunity for primary prevention and new screening methods, such as new HPV DNA testing, are promising alternatives to cytology screening that should be analyzed in the context of regional preventive programs. Cytology-based screening programs have not fulfilled their expectations and coverage does not sufficiently explain the lack of impact on screening in LAC. While improved evaluation of screening programs is necessary to increase the impact of screening on the reduction of incidence and mortality, other programmatic aspects will need to be addressed such as follow-up of positive tests and quality control. The implementation of new technologies might enhance screening performance and reduce mortality in the region. The characteristics, performance and impact of cervical cancer screening programs in LAC are reviewed in this article.

Screen-Capture Instructional Technology: A Cognitive Tool for Blended Learning

Science.gov (United States)

Smith, Jeffrey George

2012-01-01

Little empirical investigation has been conducted on high school students and teachers using online instructional multimedia developed entirely from the classroom teacher's traditional live-lecture format. This study investigated academic achievement, engagement, preference, and curriculum development using screen-capture instructional…

Screening for Intellectual Disability Using High-Resolution CMA Technology in a Retrospective Cohort from Central Brazil

Science.gov (United States)

Pereira, Rodrigo Roncato; Pinto, Irene Plaza; Minasi, Lysa Bernardes; de Melo, Aldaires Vieira; da Cruz e Cunha, Damiana Mirian; Cruz, Alex Silva; Ribeiro, Cristiano Luiz; da Silva, Cláudio Carlos; de Melo e Silva, Daniela; da Cruz, Aparecido Divino

2014-01-01

Intellectual disability is a complex, variable, and heterogeneous disorder, representing a disabling condition diagnosed worldwide, and the etiologies are multiple and highly heterogeneous. Microscopic chromosomal abnormalities and well-characterized genetic conditions are the most common causes of intellectual disability. Chromosomal Microarray Analysis analyses have made it possible to identify putatively pathogenic copy number variation that could explain the molecular etiology of intellectual disability. The aim of the current study was to identify possible submicroscopic genomic alterations using a high-density chromosomal microarray in a retrospective cohort of patients with otherwise undiagnosable intellectual disabilities referred by doctors from the public health system in Central Brazil. The CytoScan HD technology was used to detect changes in the genome copy number variation of patients who had intellectual disability and a normal karyotype. The analysis detected 18 CNVs in 60% of patients. Pathogenic CNVs represented about 22%, so it was possible to propose the etiology of intellectual disability for these patients. Likely pathogenic and unknown clinical significance CNVs represented 28% and 50%, respectively. Inherited and de novo CNVs were equally distributed. We report the nature of CNVs in patients from Central Brazil, representing a population not yet screened by microarray technologies. PMID:25061755

Integral Optimization of Systematic Parameters of Flip-Flow Screens

Institute of Scientific and Technical Information of China (English)

翟宏新

2004-01-01

The synthetic index Ks for evaluating flip-flow screens is proposed and systematically optimized in view of the whole system. A series of optimized values of relevant parameters are found and then compared with those of the current industrial specifications. The results show that the optimized value Ks approaches the one of those famous flip-flow screens in the world. Some new findings on geometric and kinematics parameters are useful for improving the flip-flow screens with a low Ks value, which is helpful in developing clean coal technology.

Evaluation of two-year Jewish genetic disease screening program in Atlanta: insight into community genetic screening approaches.

Science.gov (United States)

Shao, Yunru; Liu, Shuling; Grinzaid, Karen

2015-04-01

Improvements in genetic testing technologies have led to the development of expanded carrier screening panels for the Ashkenazi Jewish population; however, there are major inconsistencies in current screening practices. A 2-year pilot program was launched in Atlanta in 2010 to promote and facilitate screening for 19 Jewish genetic diseases. We analyzed data from this program, including participant demographics and outreach efforts. This retrospective analysis is based on a de-identified dataset of 724 screenees. Data were obtained through medical chart review and questionnaires and included demographic information, screening results, response to outreach efforts, and follow-up behavior and preferences. We applied descriptive analysis, chi-square tests, and logistic regression to analyze the data and compare findings with published literature. The majority of participants indicated that they were not pregnant or did not have a partner who was pregnant were affiliated with Jewish organizations and reported 100 % AJ ancestry. Overall, carrier frequency was 1 in 3.9. Friends, rabbis, and family members were the most common influencers of the decision to receive screening. People who were older, had a history of pregnancy, and had been previously screened were more likely to educate others (all p influencers who then encouraged screening in the target population. Educating influencers and increasing overall awareness were the most effective outreach strategies.

Graft copolymers of ethyl methacrylate on waxy maize starch derivatives as novel excipients for matrix tablets: physicochemical and technological characterisation.

Science.gov (United States)

Marinich, J A; Ferrero, C; Jiménez-Castellanos, M R

2009-05-01

Nowadays, graft copolymers are being used as an interesting option when developing a direct compression excipient for controlled release matrix tablets. New graft copolymers of ethyl methacrylate (EMA) on waxy maize starch (MS) and hydroxypropylstarch (MHS) were synthesised by free radical polymerization and alternatively dried in a vacuum oven (OD) or freeze-dried (FD). This paper evaluates the performance of these new macromolecules and discusses the effect of the carbohydrate nature and drying process on their physicochemical and technological properties. Grafting of EMA on the carbohydrate backbone was confirmed by IR and NMR spectroscopy, and the grafting yields revealed that graft copolymers present mainly a hydrophobic character. The graft copolymerization also leads to more amorphous materials with larger particle size and lower apparent density and water content than carbohydrates (MS, MHS). All the products show a lack of flow, except MHSEMA derivatives. MSEMA copolymers underwent much plastic flow and less elastic recovery than MHSEMA copolymers. Concerning the effect of drying method, FD derivatives were characterised by higher plastic deformation and less elasticity than OD derivatives. Tablets obtained from graft copolymers showed higher crushing strength and disintegration time than tablets obtained from raw starches. This behaviour suggests that these copolymers could be used as excipients in matrix tablets obtained by direct compression and with a potential use in controlled release.

Pharmacokinetic properties and tolerability of low-dose SoluMatrix diclofenac.

Science.gov (United States)

Desjardins, Paul J; Olugemo, Kemi; Solorio, Daniel; Young, Clarence L

2015-02-01

This study compared the pharmacokinetic properties and safety profile of low-dose (18- and 35-mg) diclofenac capsules manufactured using SoluMatrix Fine Particle Technology (Trademark of iCeutica Inc. (Philadelphia, Pennsylvania), and the technology is licensed to Iroko Pharmaceuticals, LLC (Philadelphia, Pennsylvania) for exclusive use in NSAIDs), which produces submicron-sized drug particles with enhanced dissolution properties, to those of diclofenac potassium immediate-release (IR) 50-mg tablets. This Phase 1, single-center, randomized, open-label, single-dose crossover study was conducted in 40 healthy volunteers. Subjects received, in randomized order, SoluMatrix diclofenac 18- or 35-mg capsules in the fasting condition, SoluMatrix diclofenac 35-mg capsules under fed conditions, and diclofenac potassium IR 50-mg tablets under fasting and fed conditions. Pharmacokinetic parameters (T(max), C(max), AUC(0-t), AUC(0-∞)) were calculated from the concentrations of diclofenac in the plasma. Absorption, food effect, and dose proportionality were determined using a mixed-model ANOVA for C(max), AUC(0-t), AUC(0-∞). Tolerability was assessed by recording adverse events, physical examination findings, vital sign measurements: clinical laboratory test results. Overall, 35 healthy volunteers aged 18 to 52 years completed the study. The mean age of the subjects was 33.4 years, and approximately half were men (47.5%). Median T(max) values were similar between the low-dose SoluMatrix diclofenac 35-mg capsules and the diclofenac potassium IR 50-mg tablets (both, ~1.0 hour). The mean maximum plasma concentration (C(max)) after the administration of low-dose SoluMatrix diclofenac 35-mg capsules was 26% lower than that with diclofenac potassium IR 50-mg tablets under fasting conditions (868.72 vs 1194.21 ng/mL). The administration of low-dose SoluMatrix diclofenac 35-mg capsules was associated with a 23% lower overall systemic exposure compared with that of diclofenac

Development and evaluation of nursing user interface screens using multiple methods.

Science.gov (United States)

Hyun, Sookyung; Johnson, Stephen B; Stetson, Peter D; Bakken, Suzanne

2009-12-01

Building upon the foundation of the Structured Narrative Electronic Health Record (EHR) model, we applied theory-based (combined Technology Acceptance Model and Task-Technology Fit Model) and user-centered methods to explore nurses' perceptions of functional requirements for an electronic nursing documentation system, design user interface screens reflective of the nurses' perspectives, and assess nurses' perceptions of the usability of the prototype user interface screens. The methods resulted in user interface screens that were perceived to be easy to use, potentially useful, and well-matched to nursing documentation tasks associated with Nursing Admission Assessment, Blood Administration, and Nursing Discharge Summary. The methods applied in this research may serve as a guide for others wishing to implement user-centered processes to develop or extend EHR systems. In addition, some of the insights obtained in this study may be informative to the development of safe and efficient user interface screens for nursing document templates in EHRs.

Magnetic Resonance Imaging as an Adjunct to Mammography for Breast Cancer Screening in Women at Less Than High Risk for Breast Cancer: A Health Technology Assessment

Science.gov (United States)

Nikitovic-Jokic, Milica; Holubowich, Corinne

2016-01-01

Background Screening with mammography can detect breast cancer early, before clinical symptoms appear. Some cancers, however, are not captured with mammography screening alone. Among women at high risk for breast cancer, magnetic resonance imaging (MRI) has been suggested as a safe adjunct (supplemental) screening tool that can detect breast cancers missed on screening mammography, potentially reducing the number of deaths associated with the disease. However, the use of adjunct screening tests may also increase the number of false-positive test results, which may lead to unnecessary follow-up testing, as well as patient stress and anxiety. We investigated the benefits and harms of MRI as an adjunct to mammography compared with mammography alone for screening women at less than high risk (average or higher than average risk) for breast cancer. Methods We searched Ovid MEDLINE, Ovid Embase, Cochrane Central Register of Controlled Trials, Cochrane Database of Systematic Reviews, Database of Abstracts of Reviews of Effects (DARE), Centre for Reviews and Dissemination (CRD) Health Technology Assessment Database, and National Health Service (NHS) Economic Evaluation Database, from January 2002 to January 2016, for evidence of effectiveness, harms, and diagnostic accuracy. Only studies evaluating the use of screening breast MRI as an adjunct to mammography in the specified populations were included. Results No studies in women at less than high risk for breast cancer met our inclusion criteria. Conclusions It remains uncertain if the use of adjunct screening breast MRI in women at less than high risk (average or higher than average risk) for breast cancer will reduce breast cancer–related mortality without significant increases in unnecessary follow-up testing and treatment. PMID:27990198

Impedance sensor technology for cell-based assays in the framework of a high-content screening system

International Nuclear Information System (INIS)

Schwarzenberger, T; Wolf, P; Brischwein, M; Kleinhans, R; Demmel, F; Becker, B; Wolf, B; Lechner, A

2011-01-01

Living cultured cells react to external influences, such as pharmaceutical agents, in an intricate manner due to their complex internal signal processing. Impedance sensing of cells on microelectrodes is a favored label-free technology to indicate cellular events, usually ascribed to morphologic alteration or changes in cellular adhesion, which is usually found in stand-alone systems that do not incorporate life support or additional sensor systems. However, only in symbiosis with metabolic activity sensing and picture documentation may a complete insight into cellular vitality be provided. This complement was created within the framework of an automated high-content screening system previously developed by our group, monitoring 24 cell culture chambers in parallel. The objective of this paper is the development of miniaturized electronics for impedance measurements and its system integration as a modular unit. In addition, it is shown how sensor electrodes were optimized by impedance matching such that spectroscopy and raw data analysis become feasible for every culture well. Undesired mechanical stress on cultured cells may arise from the medium and agent support system of the autonomous screening apparatus. This paper demonstrates how this hazard is treated with the simulation of microfluidics and impedance measurements. Physiological data are subsequently derived from the exemplary tumor cell line MCF-7 both during treatment with the agent doxorubicin and through the impact of natural killer cells. This correlates the information content of complex impedance spectra with cellular respiration as well as data from microscopy

Metallic-fibre-reinforced ceramic-matrix composite

International Nuclear Information System (INIS)

Prevost, F.; Schnedecker, G.; Boncoeur, M.

1994-01-01

A refractory metal wire cloth is embedded in an oxide ceramic matrix, using a plasma spraying technology, in order to elaborate composite plates. When mechanically tested, the composite fails with a pseudo-ductile fracture mode whereas the ceramic alone is originally brittle. It exhibits a higher fracture strength, and remains in the form of a single piece even when straining is important. No further heat treatment is needed after the original processing to reach these characteristics. (authors). 2 figs., 2 refs

D & D screening risk evaluation guidance

Energy Technology Data Exchange (ETDEWEB)

Robers, S.K.; Golden, K.M.; Wollert, D.A.

1995-09-01

The Screening Risk Evaluation (SRE) guidance document is a set of guidelines provided for the uniform implementation of SREs performed on decontamination and decommissioning (D&D) facilities. Although this method has been developed for D&D facilities, it can be used for transition (EM-60) facilities as well. The SRE guidance produces screening risk scores reflecting levels of risk through the use of risk ranking indices. Five types of possible risk are calculated from the SRE: current releases, worker exposures, future releases, physical hazards, and criticality. The Current Release Index (CRI) calculates the current risk to human health and the environment, exterior to the building, from ongoing or probable releases within a one-year time period. The Worker Exposure Index (WEI) calculates the current risk to workers, occupants and visitors inside contaminated D&D facilities due to contaminant exposure. The Future Release Index (FRI) calculates the hypothetical risk of future releases of contaminants, after one year, to human health and the environment. The Physical Hazards Index (PHI) calculates the risks to human health due to factors other than that of contaminants. Criticality is approached as a modifying factor to the entire SRE, due to the fact that criticality issues are strictly regulated under DOE. Screening risk results will be tabulated in matrix form, and Total Risk will be calculated (weighted equation) to produce a score on which to base early action recommendations. Other recommendations from the screening risk scores will be made based either on individual index scores or from reweighted Total Risk calculations. All recommendations based on the SRE will be made based on a combination of screening risk scores, decision drivers, and other considerations, as determined on a project-by-project basis.

Screening and dotting virtual slides: A new challenge for cytotechnologists

Directory of Open Access Journals (Sweden)

Walid E Khalbuss

2013-01-01

Full Text Available Digital images are increasingly being used in cytopathology. Whole-slide imaging (WSI is a digital imaging modality that uses computerized technology to scan and convert entire cytology glass slides into digital images that can be viewed on a digital display using the image viewer software. Digital image acquisition of cytology glass slides has improved significantly over the years due to the use of liquid-based preparations and advances in WSI scanning technology such as automatic multipoint pre-scan focus technology or z-stack scanning technology. Screening cytotechnologists are responsible for every cell that is present on an imaged slide. One of the challenges users have to overcome is to establish a technique to review systematically the entire imaged slide and to dot selected abnormal or significant findings. The scope of this article is to review the current user interface technology available for virtual slide navigation when screening digital slides in cytology. WSI scanner vendors provide tools, built into the image viewer software that allow for a more systematic navigation of the virtual slides, such as auto-panning, keyboard-controlled slide navigation and track map. Annotation tools can improve communication between the screener and the final reviewer or can be used for education. The tracking functionality allows recording of the WSI navigation process and provides a mechanism for confirmation of slide coverage by the screening cytotechnologist as well as a useful tool for quality assurance. As the WSI technology matures, additional features and tools to support navigation of a cytology virtual slide are anticipated.

Current state of micro-robots/devices as substitutes for screening colonoscopy: assessment based on technology readiness levels.

Science.gov (United States)

Tapia-Siles, Silvia C; Coleman, Stuart; Cuschieri, Alfred

2016-02-01

Previous reports have described several candidates, which have the potential to replace colonoscopy, but to date, there is still no device capable of fully replacing flexible colonoscopy in the management of colonic disorders and for mass adult population screening for asymptomatic colorectal cancer. NASA developed the TRL methodology to describe and define the stages of development before use and marketing of any device. The definitions of the TRLS used in the present review are those formulated by "The US Department of Defense Technology Readiness Assessment Guidance" but adapted to micro-robots for colonoscopy. All the devices included are reported in scientific literature. They were identified by a systematic search in Web of Science, PubMed and IEEE Xplore amongst other sources. Devices that clearly lack the potential for full replacement of flexible colonoscopy were excluded. The technological salient features of all the devices included for assessment are described briefly, with particular focus on device propulsion. The devices are classified according to the TRL criteria based on the reported information. An analysis is next undertaken of the characteristics and salient features of the devices included in the review: wireless/tethered devices, data storage-transmission and navigation, additional functionality, residual technology challenges and clinical and socio-economical needs. Few devices currently possess the required functionality and performance to replace the conventional colonoscopy. The requirements, including functionalities which favour the development of a micro-robot platform to replace colonoscopy, are highlighted.

Ceramic matrix and resin matrix composites - A comparison

Science.gov (United States)

Hurwitz, Frances I.

1987-01-01

The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.

Ceramic matrix and resin matrix composites: A comparison

Science.gov (United States)

Hurwitz, Frances I.

1987-01-01

The underlying theory of continuous fiber reinforcement of ceramic matrix and resin matrix composites, their fabrication, microstructure, physical and mechanical properties are contrasted. The growing use of organometallic polymers as precursors to ceramic matrices is discussed as a means of providing low temperature processing capability without the fiber degradation encountered with more conventional ceramic processing techniques. Examples of ceramic matrix composites derived from particulate-filled, high char yield polymers and silsesquioxane precursors are provided.

Screen-printed silver-ink antennas for frequency-reconfigurable architectures in LTE phones

DEFF Research Database (Denmark)

Barrio, Samantha Caporal Del; Holmgaard, Tobias; Christensen, Morten

2014-01-01

Screen printing is a proven manufacturing technology enabling high volume production at low cost. This letter investigates the achievable efficiency of a screen-printed silver antenna structure for 4G mobile phone implementation, with a market-ready solution. The contribution of each element...

Developments in SPR Fragment Screening.

Science.gov (United States)

Chavanieu, Alain; Pugnière, Martine

2016-01-01

Fragment-based approaches have played an increasing role alongside high-throughput screening in drug discovery for 15 years. The label-free biosensor technology based on surface plasmon resonance (SPR) is now sensitive and informative enough to serve during primary screens and validation steps. In this review, the authors discuss the role of SPR in fragment screening. After a brief description of the underlying principles of the technique and main device developments, they evaluate the advantages and adaptations of SPR for fragment-based drug discovery. SPR can also be applied to challenging targets such as membrane receptors and enzymes. The high-level of immobilization of the protein target and its stability are key points for a relevant screening that can be optimized using oriented immobilized proteins and regenerable sensors. Furthermore, to decrease the rate of false negatives, a selectivity test may be performed in parallel on the main target bearing the binding site mutated or blocked with a low-off-rate ligand. Fragment-based drug design, integrated in a rational workflow led by SPR, will thus have a predominant role for the next wave of drug discovery which could be greatly enhanced by new improvements in SPR devices.

High-Throughput Screening of Vascular Endothelium-Destructive or Protective Microenvironments: Cooperative Actions of Extracellular Matrix Composition, Stiffness, and Structure.

Science.gov (United States)

Ding, Yonghui; Floren, Michael; Tan, Wei

2017-06-01

Pathological modification of the subendothelial extracellular matrix (ECM) has closely been associated with endothelial activation and subsequent cardiovascular disease progression. To understand regulatory mechanisms of these matrix modifications, the majority of previous efforts have focused on the modulation of either chemical composition or matrix stiffness on 2D smooth surfaces without simultaneously probing their cooperative effects on endothelium function on in vivo like 3D fibrous matrices. To this end, a high-throughput, combinatorial microarray platform on 2D and 3D hydrogel settings to resemble the compositions, stiffness, and structure of healthy and diseased subendothelial ECM has been established, and further their respective and combined effects on endothelial attachment, proliferation, inflammation, and junctional integrity have been investigated. For the first time, the results demonstrate that 3D fibrous structure resembling native ECM is a critical endothelium-protective microenvironmental factor by maintaining the stable, quiescent endothelium with strong resistance to proinflammatory stimuli. It is also revealed that matrix stiffening, in concert with chemical compositions resembling diseased ECM, particularly collagen III, could aggravate activation of nuclear factor kappa B, disruption of endothelium integrity, and susceptibility to proinflammatory stimuli. This study elucidates cooperative effects of various microenvironmental factors on endothelial activation and sheds light on new in vitro model for cardiovascular diseases. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Changes in the Extracellular Matrix Are Associated With the Development of Serous Tubal Intraepithelial Carcinoma Into High-Grade Serous Carcinoma

NARCIS (Netherlands)

Steen, S.C.H.A. van der; Bulten, J.; Vijver, K.K. Van de; Kuppevelt, T.H. van; Massuger, L.F.

2017-01-01

OBJECTIVE: The identification of a marker for early progression of preinvasive lesions into invasive pelvic high-grade serous carcinoma (HGSC) may provide novel handles for innovative screening and prevention strategies. The interplay between cancer cells and the extracellular matrix (ECM) is one of

Parallel Programming Application to Matrix Algebra in the Spectral Method for Control Systems Analysis, Synthesis and Identification

Directory of Open Access Journals (Sweden)

V. Yu. Kleshnin

2016-01-01

Full Text Available The article describes the matrix algebra libraries based on the modern technologies of parallel programming for the Spectrum software, which can use a spectral method (in the spectral form of mathematical description to analyse, synthesise and identify deterministic and stochastic dynamical systems. The developed matrix algebra libraries use the following technologies for the GPUs: OmniThreadLibrary, OpenMP, Intel Threading Building Blocks, Intel Cilk Plus for CPUs nVidia CUDA, OpenCL, and Microsoft Accelerated Massive Parallelism.The developed libraries support matrices with real elements (single and double precision. The matrix dimensions are limited by 32-bit or 64-bit memory model and computer configuration. These libraries are general-purpose and can be used not only for the Spectrum software. They can also find application in the other projects where there is a need to perform operations with large matrices.The article provides a comparative analysis of the libraries developed for various matrix operations (addition, subtraction, scalar multiplication, multiplication, powers of matrices, tensor multiplication, transpose, inverse matrix, finding a solution of the system of linear equations through the numerical experiments using different CPU and GPU. The article contains sample programs and performance test results for matrix multiplication, which requires most of all computational resources in regard to the other operations.

Human papillomavirus self-sampling for screening nonattenders

DEFF Research Database (Denmark)

Lam, Janni Uyen Hoa; Rebolj, Matejka; Ejegod, Ditte Møller

2017-01-01

was well-accepted among nonattenders. Adopting modern technology-based platforms into the current organized screening program would serve as a convenient communication method between health authority and citizens, allowing easy access for the citizen and reducing the work load in administrating self-sampling......In organized cervical screening programs, typically 25% of the invited women do not attend. The Copenhagen Self-sampling Initiative (CSi) aimed to gain experiences on participation among screening nonattenders in the Capital Region of Denmark. Here, we report on the effectiveness of different...... communication platforms used in the pilot with suggestions for strategies prior to a full-implementation. Moreover, an innovative approach using self-sampling brushes with unique radio frequency identification chips allowed for unprecedented levels patient identification safety. Nonattenders from the capital...

Everyday multiscreening : How the simultaneous usage of multiple screens affects information processing and advertising effectiveness

NARCIS (Netherlands)

Segijn, C.M.

2017-01-01

Today, people have access to a variety of screens, such as a television, laptop, smartphone, and tablet. Screen saturation and the convergence of these technologies have led to an increase in combining different screens simultaneously, also known as multiscreening. With so many new devices and

TEACHER CANDIDATES’ VIEWS ON E-BOOKS AND SCREEN READING

Directory of Open Access Journals (Sweden)

Nevin AKKAYA

2015-08-01

Full Text Available Today, it is a necessity to make use of information technologies in creating, distributing and accessing information resources. The electronic resources as products of the developing information technologies include bibliographical text databases, e-journals, e-books, open achieves and web sites. Today, Many printed material can be accesssed by electronically in readers. Furthermore, e-books have been increasingly preferred as a mode of reading because of its advantages such as portability, storage and rich content. Individuals who want to sustain their development on this mode of reading prefer screen reading. Because reading has become a necessity because of the developing information technologies. This study aimed to examine the views of students studying Turkish language teaching at an education faculty on e-books and screen reading. Action research, one of the qualitative research design, was used during the research. Data were analyzed by content analysis. Whereas 40.7% of the ones who have taken part in this study have expressed not knowing anything about e-books, 57.8% of the participants have claimed they have knowledge about the issue of e-books. 55.3% of the participants consider that e-books contribute to the habit of reading. 73% of the participants have expressed that they have no knowledge about screen reading.

Psychometric properties of the Vulnerability to Abuse Screening Scale for screening abuse of older adults

Directory of Open Access Journals (Sweden)

Raquel Batista Dantas

Full Text Available ABSTRACT OBJECTIVE Adapt and evaluate the psychometric properties of the Vulnerability to Abuse Screening Scale to identify risk of domestic violence against older adults in Brazil. METHODS The instrument was adapted and validated in a sample of 151 older adults from a geriatric reference center in the municipality of Belo Horizonte, State of Minas Gerais, in 2014. We collected sociodemographic, clinical, and abuse-related information, and verified reliability by reproducibility in a sample of 55 older people, who underwent re-testing of the instrument seven days after the first application. Descriptive and comparative analyses were performed for all variables, with a significance level of 5%. The construct validity was analyzed by the principal components method with a tetrachoric correlation matrix, the reliability of the scale by the weighted Kappa (Kp statistic, and the internal consistency by the Kuder-Richardson estimator formula 20 (KR-20. RESULTS The average age of the participants was 72.1 years (DP = 6.96; 95%CI 70.94–73.17, with a maximum of 92 years, and they were predominantly female (76.2%; 95%CI 69.82–83.03. When analyzing the relationship between the scores of the Vulnerability to Abuse Screening Scale, categorized by presence (score > 3 or absence (score < 3 of vulnerability to abuse, with clinical and health conditions, we found statistically significant differences for self-perception of health (p = 0.002, depressive symptoms (p = 0.000, and presence of rheumatism (p = 0.003. There were no statistically significant differences between sexes. The Vulnerability to Abuse Screening Scale acceptably evaluated validity in the transcultural adaptation process, demonstrating dimensionality coherent with the original proposal (four factors. In the internal consistency analysis, the instrument presented good results (KR-20 = 0.69 and the reliability via reproducibility was considered excellent for the global scale (Kp = 0

Extended biorthogonal matrix polynomials

Directory of Open Access Journals (Sweden)

Ayman Shehata

2017-01-01

Full Text Available The pair of biorthogonal matrix polynomials for commutative matrices were first introduced by Varma and Tasdelen in [22]. The main aim of this paper is to extend the properties of the pair of biorthogonal matrix polynomials of Varma and Tasdelen and certain generating matrix functions, finite series, some matrix recurrence relations, several important properties of matrix differential recurrence relations, biorthogonality relations and matrix differential equation for the pair of biorthogonal matrix polynomials J(A,B n (x, k and K(A,B n (x, k are discussed. For the matrix polynomials J(A,B n (x, k, various families of bilinear and bilateral generating matrix functions are constructed in the sequel.

Health literacy screening instruments for eHealth applications: a systematic review.

Science.gov (United States)

Collins, Sarah A; Currie, Leanne M; Bakken, Suzanne; Vawdrey, David K; Stone, Patricia W

2012-06-01

To systematically review current health literacy (HL) instruments for use in consumer-facing and mobile health information technology screening and evaluation tools. The databases, PubMed, OVID, Google Scholar, Cochrane Library and Science Citation Index, were searched for health literacy assessment instruments using the terms "health", "literacy", "computer-based," and "psychometrics". All instruments identified by this method were critically appraised according to their reported psychometric properties and clinical feasibility. Eleven different health literacy instruments were found. Screening questions, such as asking a patient about his/her need for assistance in navigating health information, were evaluated in seven different studies and are promising for use as a valid, reliable, and feasible computer-based approach to identify patients that struggle with low health literacy. However, there was a lack of consistency in the types of screening questions proposed. There is also a lack of information regarding the psychometric properties of computer-based health literacy instruments. Only English language health literacy assessment instruments were reviewed and analyzed. Current health literacy screening tools demonstrate varying benefits depending on the context of their use. In many cases, it seems that a single screening question may be a reliable, valid, and feasible means for establishing health literacy. A combination of screening questions that assess health literacy and technological literacy may enable tailoring eHealth applications to user needs. Further research should determine the best screening question(s) and the best synthesis of various instruments' content and methodologies for computer-based health literacy screening and assessment. Copyright © 2012 Elsevier Inc. All rights reserved.

Health Literacy Screening Instruments for eHealth Applications: A Systematic Review

Science.gov (United States)

Collins, Sarah A.; Currie, Leanne M.; Bakken, Suzanne; Vawdrey, David K.; Stone, Patricia W.

2012-01-01

Objective To systematically review current health literacy (HL) instruments for use in consumer-facing and mobile health information technology screening and evaluation tools. Design The databases, PubMed, OVID, Google Scholar, Cochrane Library and Science Citation Index, were searched for health literacy assessment instruments using the terms “health”, “literacy”, “computer-based,” and “psychometrics”. All instruments identified by this method were critically appraised according to their reported psychometric properties and clinical feasibility. Results Eleven different health literacy instruments were found. Screening questions, such as asking a patient about his/her need for assistance in navigating health information, were evaluated in 7 different studies and are promising for use as a valid, reliable, and feasible computer-based approach to identify patients that struggle with low health literacy. However, there was a lack of consistency in the types of screening questions proposed. There is also a lack of information regarding the psychometric properties of computer-based health literacy instruments. Limitations Only English language health literacy assessment instruments were reviewed and analyzed. Conclusions Current health literacy screening tools demonstrate varying benefits depending on the context of their use. In many cases, it seems that a single screening question may be a reliable, valid, and feasible means for establishing health literacy. A combination of screening questions that assess health literacy and technological literacy may enable tailoring eHealth applications to user needs. Further research should determine the best screening question(s) and the best synthesis of various instruments’ content and methodologies for computer-based health literacy screening and assessment. PMID:22521719

The Brazilian energy matrix: Evolution analysis and its impact on farming

International Nuclear Information System (INIS)

Lamas, Wendell de Queiroz; Giacaglia, Giorgio Eugenio Oscare

2013-01-01

This work proposes a technical and economic analysis of the Brazilian matrix energy evaluation, aiming at the evaluation of impacts inherent to technological innovation involved on energy matrix and the sectoral development. Particular attention is given to biomass energy, natural gas, and conventional fuels, considering their impacts on agricultural activity, identifying the highest potential for investment in this sector. As a result, a clear view of the importance of agricultural sector participation in the context of the Brazilian energy is obtained, not only as a consumer, but mainly through self-production energy policy of waste reuse as biomass and of biofuels. - Highlights: • We analyze the impact of Brazilian energy matrix on farming. • We highlight the socio-political-economic impact on the agricultural sector. • We highlight the biofuels potential

Research Progress in Plasma arc welding of Magnesium Alloys and Magnesium Matrix Composites

Science.gov (United States)

Hui, Li; Yang, Zou; Yongbo, Li; Lei, Jiao; Ruijun, Hou

2017-11-01

Magnesium alloys and magnesium matrix composites by means of its excellent performance have wide application prospect in electronics, automotive, biotechnology, aerospace field, and welding technology has become a key of restricting its application. This paper describes the welding characteristics of magnesium, the obvious advantages in the application and the domestic and foreign research advance technology of plasma arc welding of magnesium, and summarizes the existing problems and development trends of plasma arc welding technology of magnesium.

A grid matrix-based Raman spectroscopic method to characterize different cell milieu in biopsied axillary sentinel lymph nodes of breast cancer patients.

Science.gov (United States)

Som, Dipasree; Tak, Megha; Setia, Mohit; Patil, Asawari; Sengupta, Amit; Chilakapati, C Murali Krishna; Srivastava, Anurag; Parmar, Vani; Nair, Nita; Sarin, Rajiv; Badwe, R

2016-01-01

Raman spectroscopy which is based upon inelastic scattering of photons has a potential to emerge as a noninvasive bedside in vivo or ex vivo molecular diagnostic tool. There is a need to improve the sensitivity and predictability of Raman spectroscopy. We developed a grid matrix-based tissue mapping protocol to acquire cellular-specific spectra that also involved digital microscopy for localizing malignant and lymphocytic cells in sentinel lymph node biopsy sample. Biosignals acquired from specific cellular milieu were subjected to an advanced supervised analytical method, i.e., cross-correlation and peak-to-peak ratio in addition to PCA and PC-LDA. We observed decreased spectral intensity as well as shift in the spectral peaks of amides and lipid bands in the completely metastatic (cancer cells) lymph nodes with high cellular density. Spectral library of normal lymphocytes and metastatic cancer cells created using the cellular specific mapping technique can be utilized to create an automated smart diagnostic tool for bench side screening of sampled lymph nodes. Spectral library of normal lymphocytes and metastatic cancer cells created using the cellular specific mapping technique can be utilized to develop an automated smart diagnostic tool for bench side screening of sampled lymph nodes supported by ongoing global research in developing better technology and signal and big data processing algorithms.

M(atrix) theory: matrix quantum mechanics as a fundamental theory

International Nuclear Information System (INIS)

Taylor, Washington

2001-01-01

This article reviews the matrix model of M theory. M theory is an 11-dimensional quantum theory of gravity that is believed to underlie all superstring theories. M theory is currently the most plausible candidate for a theory of fundamental physics which reconciles gravity and quantum field theory in a realistic fashion. Evidence for M theory is still only circumstantial -- no complete background-independent formulation of the theory exists as yet. Matrix theory was first developed as a regularized theory of a supersymmetric quantum membrane. More recently, it has appeared in a different guise as the discrete light-cone quantization of M theory in flat space. These two approaches to matrix theory are described in detail and compared. It is shown that matrix theory is a well-defined quantum theory that reduces to a supersymmetric theory of gravity at low energies. Although its fundamental degrees of freedom are essentially pointlike, higher-dimensional fluctuating objects (branes) arise through the non-Abelian structure of the matrix degrees of freedom. The problem of formulating matrix theory in a general space-time background is discussed, and the connections between matrix theory and other related models are reviewed

Reduction of multipartite qubit density matrixes to bipartite qubit density matrixes and criteria of partial separability of multipartite qubit density matrixes

OpenAIRE

Zhong, Zai-Zhe

2004-01-01

The partial separability of multipartite qubit density matrixes is strictly defined. We give a reduction way from N-partite qubit density matrixes to bipartite qubit density matrixes, and prove a necessary condition that a N-partite qubit density matrix to be partially separable is its reduced density matrix to satisfy PPT condition.

Global landscape assessment of screening technologies for medicine quality assurance: stakeholder perceptions and practices from ten countries.

Science.gov (United States)

Roth, Lukas; Nalim, Ameena; Turesson, Beth; Krech, Laura

2018-04-25

The spread of substandard and falsified (SF) medical products constitutes a growing global public health concern. Some countries use portable, handheld screening technologies (STs) in the field to accelerate detection of SF medicines and reduce the number of medicine samples that undergo costly and time-consuming confirmatory analysis. A multi-country, multi-stakeholder landscape assessment utilizing qualitative methodology was used to examine practices and perceptions related to the use of STs. Qualitative interview guides were designed using the results of a literature review and comprised of open-ended questions with the study participants, who were from national medicine regulatory authorities, pharmaceutical manufacturers, pharmacies, and distributors. Ten geographically and economically diverse countries were selected: Argentina, China, Egypt, India, Jordan, Mexico, Nigeria, Philippines, the United States, and Zimbabwe. Of the completed 53 interviews, 32 were in-person, 16 were phone interviews, and 5 were via written questionnaires. Data analysis shows a wide variation in understanding and usage of STs in different sectors. Virtually all of the study participants indicated a lack of objective, accessible information on STs to advise them on what technologies would be beneficial for their needs. Study participants also described their ideal capabilities of the next generation of STs, including shareable spectral libraries, lower acquisition costs, lesser training requirements, and in-country maintenance and technical support. The results and recommendations presented in this article can be used to help regulators communicate and justify their needs to acquire and invest in new STs. There is a need for additional standardized, trustworthy and scientifically sound evaluations of STs, and to support regulators to effectively deploy the most promising technologies. ST manufacturers can take into account some of the limitations of the technologies the interviewees

Functionalized porphyrin conjugate thin films deposited by matrix assisted pulsed laser evaporation

Energy Technology Data Exchange (ETDEWEB)

Iordache, S. [University of Bucharest, 3Nano-SAE Research Center, PO Box MG-38, Bucharest-Magurele (Romania); Cristescu, R., E-mail: rodica.cristescu@inflpr.ro [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, P.O. Box MG-36, Bucharest-Magurele (Romania); Popescu, A.C.; Popescu, C.E.; Dorcioman, G.; Mihailescu, I.N. [National Institute for Lasers, Plasma and Radiation Physics, Lasers Department, P.O. Box MG-36, Bucharest-Magurele (Romania); Ciucu, A.A. [University of Bucharest, Faculty of Chemistry, Bucharest (Romania); Balan, A.; Stamatin, I. [University of Bucharest, 3Nano-SAE Research Center, PO Box MG-38, Bucharest-Magurele (Romania); Fagadar-Cosma, E. [Institute of Chemistry Timisoara of Romanian Academy, M. Viteazul Ave. 24, 300223-Timisoara (Romania); Chrisey, D.B. [Tulane University, Departments of Physics and Biomedical Engineering, New Orleans, LA 70118 (United States)

2013-08-01

We report on the deposition of nanostructured porphyrin-base, 5(4-carboxyphenyl)-10,15,20-tris(4-phenoxyphenyl)-porphyrin thin films by matrix assisted pulsed laser evaporation onto silicon substrates with screen-printed electrodes. AFM investigations have shown that at 400 mJ/cm{sup 2} fluence a topographical transition takes place from the platelet-like stacking porphyrin-based nanostructures in a perpendicular arrangement to a quasi-parallel one both relative to the substrate surface. Raman spectroscopy has shown that the chemical structure of the deposited thin films is preserved for fluences within the range of 200–300 mJ/cm{sup 2}. Cyclic voltammograms have demonstrated that the free porphyrin is appropriate as a single mediator for glucose in a specific case of screen-printed electrodes, suggesting potential for designing a new class of biosensors.

Optical touch screen based on waveguide sensing

DEFF Research Database (Denmark)

Pedersen, Henrik Chresten; Jakobsen, Michael Linde; Hanson, Steen Grüner

2011-01-01

We disclose a simple, optical touch screen technique based on a planar injection molded polymer waveguide, a single laser, and a small linear detector array. The solution significantly reduces the complexity and cost as compared to existing optical touch technologies. Force detection of a touching...

The Benefits of Single-Touch Screens in Intersubjective Meaning Making

DEFF Research Database (Denmark)

Davidsen, Jacob; Christiansen, Ellen Tove

2013-01-01

the possibilities for equal levels of verbal and physical participation.Additionally, these studies suggest that multi-touch technologies offer more task-oriented activities compared to single-touch screen interaction, in which discussion about turn-taking is more prevalent from the outset. In contrast, applying......What are the benefits of single-touch screens? The paper presents findings of one video extract from ten months of observation of single-touch screen interaction among 8-9 year-old children. Recent studies of collaborative learning mediated by digital touch screens and tabletops emphasize...... the Embodied Interaction Analysis, we find that the constraints of single-touch screens offer support for intersubjective meaning making in their capacity of constraining the interaction. This “grain of sand” shows how children display and construct a shared work space through embodied interaction...

Evaluation of a specialized filter-paper matrix for transportation of extended bovine semen to screen for bovine herpesvirus-1 by real-time PCR.

Science.gov (United States)

Sarangi, Laxmi Narayan; Naveena, Thodangala; Rana, Samir Kumar; Surendra, Kota Sri Naga Leela; Reddy, Rachamreddy Venkata Chandrasekhar; Bajibabu, Putla; Ponnanna, Nadikerianda Muthappa; Sharma, Girish Kumar; Srinivasan, Villuppanoor Alwar

2018-07-01

The extended frozen semen (EFS) batches produced from infectious bovine rhinotracheitis (IBR) sero-positive cattle and buffalo bulls housed in various semen stations in India are transported to the testing laboratory in liquid nitrogen (LN 2 ) for screening bovine herpesvirus-1 (BoHV-1). This procedure is laborious and poses LN 2 related hazards. An alternative logistics for transportation of samples was investigated. Use of Flinders Technology Associates (FTA ® ) elute card was evaluated for transportation of extended bovine semen to screen BoHV-1 DNA by real-time PCR targeting gB gene and the method was compared with the OIE approved Chelex resin based method. A protocol for extraction of BoHV-1 DNA from FTA ® card spotted with extended semen was optimized. The viral DNA was found to be stable on FTA ® card for at least 28 days when the cards are stored at 4°-37 °C. The analytical sensitivity for the assay was determined using variable dilutions of BoHV-1 spiked semen and positive plasmid harbouring gB gene (97bp) spotted onto FTA ® card and it was found to be 10 0.8 TCID 50 /ml or 100 copies respectively in real-time PCR. The test could detect as low as 10 0.008 TCID 50 /ml or 1 copy of positive plasmid when more number of replicates (n = 6) of the same sample were tested. This sensitivity was found to be comparable to Chelex method and both the methods demonstrated a very strong correlation (r = 0.9774; 95% CI: 0.9620-0.9860) in terms of Ct value (p FTA method in comparison to the Chelex method was 83.08% (95% CI: 71.73%-91.24%) and 93.23% (95% CI: 89.38%-96.01%) respectively when 316 samples were screened by both the methods. The degree of agreement between these two tests was good (Kappa value: 0.738; 95% CI: 0.646-0.829). The method was found to be robust and highly repeatable in inter-assay and intra-assay precision testing. The result suggests that the FTA ® card holds promise as an alternative system for transportation of EFS for

Cancer Screening and Genetics: A Tale of Two Paradigms

OpenAIRE

Hamilton, Jada G.; Edwards, Heather M.; Khoury, Muin J.; Taplin, Stephen H.

2014-01-01

The long-standing medical tradition to “first do no harm” is reflected in population-wide evidence-based recommendations for cancer screening tests that focus primarily on reducing morbidity and mortality. The conventional cancer screening process is predicated on finding early-stage disease that can be treated effectively; yet emerging genetic and genomic testing technologies have moved the target earlier in the disease development process to identify a probabilistic predisposition to diseas...

Policy Forum Improving the screening and treatment of hypertension ...

African Journals Online (AJOL)

2008-12-27

Dec 27, 2008 ... advantages and disadvantages associated with screening and referral. Policy Option 3: ... Skill-building approaches such as training with healthcare workers or .... Science and Technology, Grand Challenges Canada and.

Integration of an In Situ MALDI-Based High-Throughput Screening Process: A Case Study with Receptor Tyrosine Kinase c-MET.

Science.gov (United States)

Beeman, Katrin; Baumgärtner, Jens; Laubenheimer, Manuel; Hergesell, Karlheinz; Hoffmann, Martin; Pehl, Ulrich; Fischer, Frank; Pieck, Jan-Carsten

2017-12-01

Mass spectrometry (MS) is known for its label-free detection of substrates and products from a variety of enzyme reactions. Recent hardware improvements have increased interest in the use of matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) MS for high-throughput drug discovery. Despite interest in this technology, several challenges remain and must be overcome before MALDI-MS can be integrated as an automated "in-line reader" for high-throughput drug discovery. Two such hurdles include in situ sample processing and deposition, as well as integration of MALDI-MS for enzymatic screening assays that usually contain high levels of MS-incompatible components. Here we adapt our c-MET kinase assay to optimize for MALDI-MS compatibility and test its feasibility for compound screening. The pros and cons of the Echo (Labcyte) as a transfer system for in situ MALDI-MS sample preparation are discussed. We demonstrate that this method generates robust data in a 1536-grid format. We use the MALDI-MS to directly measure the ratio of c-MET substrate and phosphorylated product to acquire IC50 curves and demonstrate that the pharmacology is unaffected. The resulting IC50 values correlate well between the common label-based capillary electrophoresis and the label-free MALDI-MS detection method. We predict that label-free MALDI-MS-based high-throughput screening will become increasingly important and more widely used for drug discovery.

Nontargeted Screening Method for Illegal Additives Based on Ultrahigh-Performance Liquid Chromatography-High-Resolution Mass Spectrometry.

Science.gov (United States)

Fu, Yanqing; Zhou, Zhihui; Kong, Hongwei; Lu, Xin; Zhao, Xinjie; Chen, Yihui; Chen, Jia; Wu, Zeming; Xu, Zhiliang; Zhao, Chunxia; Xu, Guowang

2016-09-06

Identification of illegal additives in complex matrixes is important in the food safety field. In this study a nontargeted screening strategy was developed to find illegal additives based on ultrahigh-performance liquid chromatography-high-resolution mass spectrometry (UHPLC-HRMS). First, an analytical method for possible illegal additives in complex matrixes was established including fast sample pretreatment, accurate UHPLC separation, and HRMS detection. Second, efficient data processing and differential analysis workflow were suggested and applied to find potential risk compounds. Third, structure elucidation of risk compounds was performed by (1) searching online databases [Metlin and the Human Metabolome Database (HMDB)] and an in-house database which was established at the above-defined conditions of UHPLC-HRMS analysis and contains information on retention time, mass spectra (MS), and tandem mass spectra (MS/MS) of 475 illegal additives, (2) analyzing fragment ions, and (3) referring to fragmentation rules. Fish was taken as an example to show the usefulness of the nontargeted screening strategy, and six additives were found in suspected fish samples. Quantitative analysis was further carried out to determine the contents of these compounds. The satisfactory application of this strategy in fish samples means that it can also be used in the screening of illegal additives in other kinds of food samples.

Prenatal screening at 11-13+6 weeks in assisted reproductive technology singleton pregnancies and those conceived naturally.

Science.gov (United States)

Gong, Meng; Shi, Hua; Zhang, Yu-guo; Ming, Lei

2015-10-01

To investigate whether assisted reproductive technology (ART) increases the risk of fetal chromosomal abnormalities. A total of 2034 singleton pregnant women were included in this retrospective study. They were divided into ART (574 fetuses) and control groups (1460 fetuses conceived naturally). All pregnant women received screening according to the Fetal Medicine Foundation, London 2004 Kypros H. Nicolaides guidelines at 11-13+6 weeks of gestation. Accordingly, women with value at risk of chromosomal abnormalities >1:250 underwent chorionic villus sampling or amniocentesis. Mean body mass index was 22.83 ± 3.27 versus 21.29 ± 2.81 kg/m(2) in the ART and control groups, respectively (P fetal chromosomal abnormalities. Additionally, fetus size in the ART group was bigger than that in the natural conception group. © 2015 Japan Society of Obstetrics and Gynecology.

Matrix theory

CERN Document Server

Franklin, Joel N

2003-01-01

Mathematically rigorous introduction covers vector and matrix norms, the condition-number of a matrix, positive and irreducible matrices, much more. Only elementary algebra and calculus required. Includes problem-solving exercises. 1968 edition.

D ampersand D screening risk evaluation guidance

International Nuclear Information System (INIS)

Robers, S.K.; Golden, K.M.; Wollert, D.A.

1995-09-01

The Screening Risk Evaluation (SRE) guidance document is a set of guidelines provided for the uniform implementation of SREs performed on decontamination and decommissioning (D ampersand D) facilities. Although this method has been developed for D ampersand D facilities, it can be used for transition (EM-60) facilities as well. The SRE guidance produces screening risk scores reflecting levels of risk through the use of risk ranking indices. Five types of possible risk are calculated from the SRE: current releases, worker exposures, future releases, physical hazards, and criticality. The Current Release Index (CRI) calculates the current risk to human health and the environment, exterior to the building, from ongoing or probable releases within a one-year time period. The Worker Exposure Index (WEI) calculates the current risk to workers, occupants and visitors inside contaminated D ampersand D facilities due to contaminant exposure. The Future Release Index (FRI) calculates the hypothetical risk of future releases of contaminants, after one year, to human health and the environment. The Physical Hazards Index (PHI) calculates the risks to human health due to factors other than that of contaminants. Criticality is approached as a modifying factor to the entire SRE, due to the fact that criticality issues are strictly regulated under DOE. Screening risk results will be tabulated in matrix form, and Total Risk will be calculated (weighted equation) to produce a score on which to base early action recommendations. Other recommendations from the screening risk scores will be made based either on individual index scores or from reweighted Total Risk calculations. All recommendations based on the SRE will be made based on a combination of screening risk scores, decision drivers, and other considerations, as determined on a project-by-project basis

Breast Cancer Screening in an Era of Personalized Regimens

Science.gov (United States)

Onega, Tracy; Beaber, Elisabeth F.; Sprague, Brian L.; Barlow, William E.; Haas, Jennifer S.; Tosteson, Anna N.A.; Schnall, Mitchell D.; Armstrong, Katrina; Schapira, Marilyn M.; Geller, Berta; Weaver, Donald L.; Conant, Emily F.

2014-01-01

Breast cancer screening holds a prominent place in public health, health care delivery, policy, and women’s health care decisions. Several factors are driving shifts in how population-based breast cancer screening is approached, including advanced imaging technologies, health system performance measures, health care reform, concern for “overdiagnosis,” and improved understanding of risk. Maximizing benefits while minimizing the harms of screening requires moving from a “1-size-fits-all” guideline paradigm to more personalized strategies. A refined conceptual model for breast cancer screening is needed to align women’s risks and preferences with screening regimens. A conceptual model of personalized breast cancer screening is presented herein that emphasizes key domains and transitions throughout the screening process, as well as multilevel perspectives. The key domains of screening awareness, detection, diagnosis, and treatment and survivorship are conceptualized to function at the level of the patient, provider, facility, health care system, and population/policy arena. Personalized breast cancer screening can be assessed across these domains with both process and outcome measures. Identifying, evaluating, and monitoring process measures in screening is a focus of a National Cancer Institute initiative entitled PROSPR (Population-based Research Optimizing Screening through Personalized Regimens), which will provide generalizable evidence for a risk-based model of breast cancer screening, The model presented builds on prior breast cancer screening models and may serve to identify new measures to optimize benefits-to-harms tradeoffs in population-based screening, which is a timely goal in the era of health care reform. PMID:24830599

[Screening of anti-aging active ingredients and mechanism analysis based on molecular docking technology].

Science.gov (United States)

Du, Ran-Feng; Zhang, Xiao-Hua; Ye, Xiao-Tong; Yu, Wen-Kang; Wang, Yun

2016-07-01

Dampness evil is the source of all diseases, which is easy to cause disease and promote aging, while aging could also promote the occurence and development of diseases. In this paper, the relationship between the dampness evil and aging would be discussed, to find the anti-aging active ingredients in traditional Chinese medicine (TCM), and analyze the anti-aging mechanism of dampness eliminating drug. Molecular docking technology was used, with aging-related mammalian target of rapamycin as the docking receptors, and chemical components of Fuling, Sangzhi, Mugua, Yiyiren and Houpo as the docking molecules, to preliminarily screen the anti-aging active ingredients in dampness eliminating drug. Through the comparison with active drugs already on the market (temsirolimus and everolimus), 12 kinds of potential anti-aging active ingredients were found, but their drug gability still needs further study. The docking results showed that various components in the dampness eliminating drug can play anti-aging activities by acting on mammalian target of rapamycin. This result provides a new thought and direction for the method of delaying aging by eliminating dampness. Copyright© by the Chinese Pharmaceutical Association.

Risk of cancer radioinduced by mammographic screening

International Nuclear Information System (INIS)

Correa, Rosangela da Silveira; Peixoto, Joao Emilio; Ferreira, Rubemar de Souza; Freitas-Junior, Ruffo

2013-01-01

This work aims to estimate the risk benefit of mammography, in terms of the number of lives saved/number of lives lost, in the female population of the State of Goias, Brazil, depending on the age range indicated for screening and the type of technology available

Usability and Accessibility of eBay by Screen Reader

Science.gov (United States)

Buzzi, Maria Claudia; Buzzi, Marina; Leporini, Barbara; Akhter, Fahim

The evolution of Information and Communication Technology and the rapid growth of the Internet have fuelled a great diffusion of eCommerce websites. Usually these sites have complex layouts crowded with active elements, and thus are difficult to navigate via screen reader. Interactive environments should be properly designed and delivered to everyone, including the blind, who usually use screen readers to interact with their computers. In this paper we investigate the interaction of blind users with eBay, a popular eCommerce website, and discuss how using the W3C Accessible Rich Internet Applications (WAI-ARIA) suite could improve the user experience when navigating via screen reader.

Mechanical Properties of TC4 Matrix Composites Prepared by Laser Cladding

Directory of Open Access Journals (Sweden)

WANG Lin

2017-06-01

Full Text Available In order to improve the penetration performance of TC4, the direct laser deposition technology was used to prepare TC4 composite material. TA15+30% TiC powder, TA15+20%Cr3C2 powder and TA15+15%B4C powder were used as deposited materials for TC4 matrix. The micromorphology, change of hardness of the deposited coating and mechanical properties of the three composites were studied. The experimental results demonstrate that the TC4 matrix with the three kinds of materials can form a complete metallurgical bonding, and the strength of TC4-(TA15+TiC, TC4-(TA15+Cr3C2 and TC4-(TA15+B4C are higher than that of TC4 matrix materials, while the plasticity is slightly worse.

Extracellular matrix components direct porcine muscle stem cell behavior

International Nuclear Information System (INIS)

Wilschut, Karlijn J.; Haagsman, Henk P.; Roelen, Bernard A.J.

2010-01-01

In muscle tissue, extracellular matrix proteins, together with the vasculature system, muscle-residence cells and muscle fibers, create the niche for muscle stem cells. The niche is important in controlling proliferation and directing differentiation of muscle stem cells to sustain muscle tissue. Mimicking the extracellular muscle environment improves tools exploring the behavior of primary muscle cells. Optimizing cell culture conditions to maintain muscle commitment is important in stem cell-based studies concerning toxicology screening, ex vivo skeletal muscle tissue engineering and in the enhancement of clinical efficiency. We used the muscle extracellular matrix proteins collagen type I, fibronectin, laminin, and also gelatin and Matrigel as surface coatings of tissue culture plastic to resemble the muscle extracellular matrix. Several important factors that determine myogenic commitment of the primary muscle cells were characterized by quantitative real-time RT-PCR and immunofluorescence. Adhesion of high PAX7 expressing satellite cells was improved if the cells were cultured on fibronectin or laminin coatings. Cells cultured on Matrigel and laminin coatings showed dominant integrin expression levels and exhibited an activated Wnt pathway. Under these conditions both stem cell proliferation and myogenic differentiation capacity were superior if compared to cells cultured on collagen type I, fibronectin and gelatin. In conclusion, Matrigel and laminin are the preferred coatings to sustain the proliferation and myogenic differentiation capacity of the primary porcine muscle stem cells, when cells are removed from their natural environment for in vitro culture.

Extracellular matrix components direct porcine muscle stem cell behavior

Energy Technology Data Exchange (ETDEWEB)

Wilschut, Karlijn J. [Department of Farm Animal Health, Faculty of Veterinary Medicine, Utrecht University, Yalelaan 104, 3584 CM, Utrecht (Netherlands); Haagsman, Henk P. [Department of Infectious Diseases and Immunology, Faculty of Veterinary Medicine, Utrecht University, Yalelaan 1, 3584 CL, Utrecht (Netherlands); Roelen, Bernard A.J., E-mail: b.a.j.roelen@uu.nl [Department of Farm Animal Health, Faculty of Veterinary Medicine, Utrecht University, Yalelaan 104, 3584 CM, Utrecht (Netherlands)

2010-02-01

In muscle tissue, extracellular matrix proteins, together with the vasculature system, muscle-residence cells and muscle fibers, create the niche for muscle stem cells. The niche is important in controlling proliferation and directing differentiation of muscle stem cells to sustain muscle tissue. Mimicking the extracellular muscle environment improves tools exploring the behavior of primary muscle cells. Optimizing cell culture conditions to maintain muscle commitment is important in stem cell-based studies concerning toxicology screening, ex vivo skeletal muscle tissue engineering and in the enhancement of clinical efficiency. We used the muscle extracellular matrix proteins collagen type I, fibronectin, laminin, and also gelatin and Matrigel as surface coatings of tissue culture plastic to resemble the muscle extracellular matrix. Several important factors that determine myogenic commitment of the primary muscle cells were characterized by quantitative real-time RT-PCR and immunofluorescence. Adhesion of high PAX7 expressing satellite cells was improved if the cells were cultured on fibronectin or laminin coatings. Cells cultured on Matrigel and laminin coatings showed dominant integrin expression levels and exhibited an activated Wnt pathway. Under these conditions both stem cell proliferation and myogenic differentiation capacity were superior if compared to cells cultured on collagen type I, fibronectin and gelatin. In conclusion, Matrigel and laminin are the preferred coatings to sustain the proliferation and myogenic differentiation capacity of the primary porcine muscle stem cells, when cells are removed from their natural environment for in vitro culture.

Information technology-enabled team-based, patient-centered care: The example of depression screening and management in cancer care.

Science.gov (United States)

Randhawa, Gurvaneet S; Ahern, David K; Hesse, Bradford W

2017-03-01

The existing healthcare delivery systems across the world need to be redesigned to ensure high-quality care is delivered to all patients. This redesign needs to ensure care is knowledge-based, patient-centered and systems-minded. The rapid advances in the capabilities of information and communication technology and its recent rapid adoption in healthcare delivery have ensured this technology will play a vital role in the redesign of the healthcare delivery system. This commentary highlights promising new developments in health information technology (IT) that can support patient engagement and self-management as well as team-based, patient-centered care. Collaborative care is an effective approach to screen and treat depression in cancer patients and it is a good example of the benefits of team-based and patient-centered care. However, this approach was developed prior to the widespread adoption and use of health IT. We provide examples to illustrate how health IT can improve prevention and treatment of depression in cancer patients. We found several knowledge gaps that limit our ability to realize the full potential of health IT in the context of cancer and comorbid depression care. These gaps need to be filled to improve patient engagement; enhance the reach and effectiveness of collaborative care and web-based programs to prevent and treat depression in cancer patients. We also identify knowledge gaps in health IT design and implementation. Filling these gaps will help shape policies that enable clinical teams to deliver high-quality cancer care globally.

The University of Kansas High-Throughput Screening Laboratory. Part II: enabling collaborative drug-discovery partnerships through cutting-edge screening technology.

Science.gov (United States)

McDonald, Peter R; Roy, Anuradha; Chaguturu, Rathnam

2011-07-01

The University of Kansas High-Throughput Screening (KU HTS) core is a state-of-the-art drug-discovery facility with an entrepreneurial open-service policy, which provides centralized resources supporting public- and private-sector research initiatives. The KU HTS core was established in 2002 at the University of Kansas with support from an NIH grant and the state of Kansas. It collaborates with investigators from national and international academic, nonprofit and pharmaceutical organizations in executing HTS-ready assay development and screening of chemical libraries for target validation, probe selection, hit identification and lead optimization. This is part two of a contribution from the KU HTS laboratory.

Fuzzy vulnerability matrix

International Nuclear Information System (INIS)

Baron, Jorge H.; Rivera, S.S.

2000-01-01

The so-called vulnerability matrix is used in the evaluation part of the probabilistic safety assessment for a nuclear power plant, during the containment event trees calculations. This matrix is established from what is knows as Numerical Categories for Engineering Judgement. This matrix is usually established with numerical values obtained with traditional arithmetic using the set theory. The representation of this matrix with fuzzy numbers is much more adequate, due to the fact that the Numerical Categories for Engineering Judgement are better represented with linguistic variables, such as 'highly probable', 'probable', 'impossible', etc. In the present paper a methodology to obtain a Fuzzy Vulnerability Matrix is presented, starting from the recommendations on the Numerical Categories for Engineering Judgement. (author)

Green's matrix for a second-order self-adjoint matrix differential operator

International Nuclear Information System (INIS)

Sisman, Tahsin Cagri; Tekin, Bayram

2010-01-01

A systematic construction of the Green's matrix for a second-order self-adjoint matrix differential operator from the linearly independent solutions of the corresponding homogeneous differential equation set is carried out. We follow the general approach of extracting the Green's matrix from the Green's matrix of the corresponding first-order system. This construction is required in the cases where the differential equation set cannot be turned to an algebraic equation set via transform techniques.

Binding of matrix metalloproteinase inhibitors to extracellular matrix: 3D-QSAR analysis.

Science.gov (United States)

Zhang, Yufen; Lukacova, Viera; Bartus, Vladimir; Nie, Xiaoping; Sun, Guorong; Manivannan, Ethirajan; Ghorpade, Sandeep R; Jin, Xiaomin; Manyem, Shankar; Sibi, Mukund P; Cook, Gregory R; Balaz, Stefan

2008-10-01

Binding to the extracellular matrix, one of the most abundant human protein complexes, significantly affects drug disposition. Specifically, the interactions with extracellular matrix determine the free concentrations of small molecules acting in tissues, including signaling peptides, inhibitors of tissue remodeling enzymes such as matrix metalloproteinases, and other drug candidates. The nature of extracellular matrix binding was elucidated for 63 matrix metalloproteinase inhibitors, for which the association constants to an extracellular matrix mimic were reported here. The data did not correlate with lipophilicity as a common determinant of structure-nonspecific, orientation-averaged binding. A hypothetical structure of the binding site of the solidified extracellular matrix surrogate was analyzed using the Comparative Molecular Field Analysis, which needed to be applied in our multi-mode variant. This fact indicates that the compounds bind to extracellular matrix in multiple modes, which cannot be considered as completely orientation-averaged and exhibit structural dependence. The novel comparative molecular field analysis models, exhibiting satisfactory descriptive and predictive abilities, are suitable for prediction of the extracellular matrix binding for the untested chemicals, which are within applicability domains. The results contribute to a better prediction of the pharmacokinetic parameters such as the distribution volume and the tissue-blood partition coefficients, in addition to a more imminent benefit for the development of more effective matrix metalloproteinase inhibitors.

Progress in the development of photosensitive GEMs with resistive electrodes manufactured by a screen printing technology

International Nuclear Information System (INIS)

Peskov, V.; Martinengo, P.; Nappi, E.; Oliveira, R.; Paic, G.; Pietropaolo, F.; Picchi, P.

2009-01-01

An innovative photosensitive gaseous detector, consisting of a GEM-like amplification structure with double-layered electrodes (instead of commonly used metallic ones) coated with a CsI reflective photocathode, is described. In one of our latest designs, the inner electrode consists of a metallic grid and the outer one is made of resistive strips; the latter are manufactured by a screen-printing technology on the top of the metallic strips's grid The inner metallic grid is used for 2-D position measurements whereas the resistive layer provides an efficient spark-protected operation at high gains close to the breakdown limit. Detectors with active areas of 10x10 and 10x20 cm 2 were tested under various conditions including the operation in photosensitive gas mixtures containing ethylferrocene or TMAE vapors. The new technique could have many applications requiring robust and reliable large-area detectors for UV visualization, as for example, in Cherenkov imaging devices.

Progress in the development of photosensitive GEMs with resistive electrodes manufactured by a screen printing technology

CERN Document Server

Peskov, V; Nappi, E; Oliveira, R; Paic, G; Pietropaolo, F; Picchi, P

2009-01-01

An innovative photosensitive gaseous detector, consisting of a GEM-like amplification structure with double-layered electrodes (instead of commonly used metallic ones) coated with a CsI reflective photocathode, is described. In one of our latest designs, the inner electrode consists of a metallic grid and the outer one is made of resistive strips; the latter are manufactured by a screen-printing technology on the top of the metallic strips's grid The inner metallic grid is used for 2-D position measurements whereas the resistive layer provides an efficient spark-protected operation at high gains close to the breakdown limit. Detectors with active areas of 10×10 and 10×20 cm2 were tested under various conditions including the operation in photosensitive gas mixtures containing ethylferrocene or TMAE vapors. The new technique could have many applications requiring robust and reliable large-area detectors for UV visualization, as for example, in Cherenkov imaging devices.

Diagnostic of the charcoal's productive and commercialize in the Pinar del Río's Integral Forest Company by matrix SWOT

Directory of Open Access Journals (Sweden)

Van Anh Thi Nguyen

2014-06-01

Full Text Available This study aimed to diagnose the situation productive of charcoal in Pinar del Río EFI by SWOT matrix (weaknesses, threats, strengths and opportunities which consists of the collection of information from different sources related to the production of charcoal and thus a screening of ideas and through the technical working group with the presence of specialists proceeded develop the matrix with all components was performed. The results of the assessment of the productive situation of charcoal indicate an unfavorable position, resulting in a strategy of adaptive type, conditioned by economic, political and cultural factors.

A model for overview of student learning: a matrix of educational outcomes versus methodologies.

Science.gov (United States)

Johnsen, David C; Marshall, Teresa A; Finkelstein, Michael W; Cunningham-Ford, Marsha A; Straub-Morarend, Cheryl L; Holmes, David C; Armstrong, Steven R; Aquilino, Steven A; Sharp, Helen M; Solow, Catherine M; McQuistan, Michelle R

2011-02-01

A concise overview of an institution's aspirations for its students becomes increasingly elusive because dental education has evolving emphases on priorities like critical thinking and adapting to new technology. The purpose of this article is to offer a learner-oriented matrix that gives a focus for discussion and an overview of an institution's educational outcomes. On one axis of the matrix, common educational outcomes are listed: knowledge, technical skills, critical thinking, ethical and professional values, patient and practice management, and social responsibility awareness. On the other axis, methodologies are listed: definition, cultivation strategies, measures (summative/formative, objective/subjective), institutional coordination, and competency determination. By completing the matrix, an overview of the process by which students reach these outcomes emerges. Each institution would likely complete the matrix differently and, ideally, with active discussion. While the matrix can first be used to establish "Where are we now?" for an institution, it can also be a starting point for more extensive matrices and further discussion. Vertical and horizontal analyses of the matrix provide a unique lens for viewing the institution's learning environment.

Fast screening of short-chain chlorinated paraffins in indoor dust samples by graphene-assisted laser desorption/ionization mass spectrometry.

Science.gov (United States)

Huang, Xiu; Liu, Qian; Gao, Wei; Wang, Yawei; Nie, Zhou; Yao, Shouzhuo; Jiang, Guibin

2018-03-01

As an important class of emerging chemical contaminants, short-chain chlorinated paraffins (SCCPs) are considered as one of the most challenging groups of compounds to analyze. In this paper, we report a new method for fast screening of SCCPs based on matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) with graphene as a matrix and 2,5,6,9-tetrachlorodecane as an internal standard. We found that the use of graphene as MALDI matrix generated high peak intensities for SCCPs while producing few background noises. The ion fragmentation mechanisms of SCCPs in MALDI are discussed in detail. Under the optimized conditions, much lower detection limits of SCCP congeners (0.1-5ng/mL) than those reported previously were obtained. Other distinct advantages such as short analysis time and simplified sample preparation procedures are also demonstrated. The method was successfully applied in fast screening of SCCPs in indoor dust samples and monitoring of human exposure levels to SCCPs, and the results were verified by gas chromatography coupled to negative chemical ionization quadrupole time-of-flight high-resolution mass spectrometry. This work not only offers a new promising tool for SCCP studies, but also further demonstrates the promise of graphene as a new generation of MALDI matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

Advanced biomaterials and microengineering technologies to recapitulate the stepwise process of cancer metastasis.

Science.gov (United States)

Peela, Nitish; Truong, Danh; Saini, Harpinder; Chu, Hunghao; Mashaghi, Samaneh; Ham, Stephanie L; Singh, Sunil; Tavana, Hossein; Mosadegh, Bobak; Nikkhah, Mehdi

2017-07-01

Cancer is one of the leading causes of death globally according to the World Health Organization. Although improved treatments and early diagnoses have reduced cancer related mortalities, metastatic disease remains a major clinical challenge. The local tumor microenvironment plays a significant role in cancer metastasis, where tumor cells respond and adapt to a plethora of biochemical and biophysical signals from stromal cells and extracellular matrix (ECM) proteins. Due to these complexities, there is a critical need to understand molecular mechanisms underlying cancer metastasis to facilitate the discovery of more effective therapies. In the past few years, the integration of advanced biomaterials and microengineering approaches has initiated the development of innovative platform technologies for cancer research. These technologies enable the creation of biomimetic in vitro models with physiologically relevant (i.e. in vivo-like) characteristics to conduct studies ranging from fundamental cancer biology to high-throughput drug screening. In this review article, we discuss the biological significance of each step of the metastatic cascade and provide a broad overview on recent progress to recapitulate these stages using advanced biomaterials and microengineered technologies. In each section, we will highlight the advantages and shortcomings of each approach and provide our perspectives on future directions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Digital Technology and Student Cognitive Development

Science.gov (United States)

Cavanaugh, J. Michael; Giapponi, Catherine C.; Golden, Timothy D.

2016-01-01

Digital technology has proven a beguiling, some even venture addictive, presence in the lives of our 21st century (millennial) students. And while screen technology may offer select cognitive benefits, there is mounting evidence in the cognitive neuroscience literature that digital technology is restructuring the way our students read and think,…

A methodological overview on molecular preimplantation genetic diagnosis and screening: a genomic future?

Science.gov (United States)

Vendrell, Xavier; Bautista-Llácer, Rosa

2012-12-01

The genetic diagnosis and screening of preimplantation embryos generated by assisted reproduction technology has been consolidated in the prenatal care framework. The rapid evolution of DNA technologies is tending to molecular approaches. Our intention is to present a detailed methodological view, showing different diagnostic strategies based on molecular techniques that are currently applied in preimplantation genetic diagnosis. The amount of DNA from one single, or a few cells, obtained by embryo biopsy is a limiting factor for the molecular analysis. In this sense, genetic laboratories have developed molecular protocols considering this restrictive condition. Nevertheless, the development of whole-genome amplification methods has allowed preimplantation genetic diagnosis for two or more indications simultaneously, like the selection of histocompatible embryos plus detection of monogenic diseases or aneuploidies. Moreover, molecular techniques have permitted preimplantation genetic screening to progress, by implementing microarray-based comparative genome hybridization. Finally, a future view of the embryo-genetics field based on molecular advances is proposed. The normalization, cost-effectiveness analysis, and new technological tools are the next topics for preimplantation genetic diagnosis and screening. Concomitantly, these additions to assisted reproduction technologies could have a positive effect on the schedules of preimplantation studies.

Matrix calculus

CERN Document Server

Bodewig, E

1959-01-01

Matrix Calculus, Second Revised and Enlarged Edition focuses on systematic calculation with the building blocks of a matrix and rows and columns, shunning the use of individual elements. The publication first offers information on vectors, matrices, further applications, measures of the magnitude of a matrix, and forms. The text then examines eigenvalues and exact solutions, including the characteristic equation, eigenrows, extremum properties of the eigenvalues, bounds for the eigenvalues, elementary divisors, and bounds for the determinant. The text ponders on approximate solutions, as well

Neutrino mass matrix

International Nuclear Information System (INIS)

Strobel, E.L.

1985-01-01

Given the many conflicting experimental results, examination is made of the neutrino mass matrix in order to determine possible masses and mixings. It is assumed that the Dirac mass matrix for the electron, muon, and tau neutrinos is similar in form to those of the quarks and charged leptons, and that the smallness of the observed neutrino masses results from the Gell-Mann-Ramond-Slansky mechanism. Analysis of masses and mixings for the neutrinos is performed using general structures for the Majorana mass matrix. It is shown that if certain tentative experimental results concerning the neutrino masses and mixing angles are confirmed, significant limitations may be placed on the Majorana mass matrix. The most satisfactory simple assumption concerning the Majorana mass matrix is that it is approximately proportional to the Dirac mass matrix. A very recent experimental neutrino mass result and its implications are discussed. Some general properties of matrices with structure similar to the Dirac mass matrices are discussed

Hearing Screening Follow-Up: Completing the Process to Identify Hearing Health Needs

Science.gov (United States)

Eiserman, William; Shisler, Lenore; Hoffman, Jeff

2015-01-01

Hearing is at the heart of language development and school readiness; increasing numbers of Early Head Start programs have come to rely on otoacoustic emissions (OAE) technology to screen all infants and toddlers for hearing loss. Successful identification of hearing health needs is dependent not only on an appropriate screening method, but also…

Prenatal screening for fetal aneuploidy in singleton pregnancies.

Science.gov (United States)

Chitayat, David; Langlois, Sylvie; Douglas Wilson, R

2011-07-01

studies. There were no language restrictions. Searches were updated on a regular basis and incorporated in the guideline to August 2010. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology assessment-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The previous Society of Obstetricians and Gynaecologists of Canada guidelines regarding prenatal screening were also reviewed in developing this clinical practice guideline. The quality of evidence was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care. This guideline is intended to reduce the number of prenatal invasive procedures done when maternal age is the only indication. This will have the benefit of reducing the numbers of normal pregnancies lost because of complications of invasive procedures. Any screening test has an inherent false-positive rate, which may result in undue anxiety. It is not possible at this time to undertake a detailed cost-benefit analysis of the implementation of this guideline, since this would require health surveillance and research and health resources not presently available; however, these factors need to be evaluated in a prospective approach by provincial and territorial initiatives. RECOMMENDATIONS 1. All pregnant women in Canada, regardless of age, should be offered, through an informed counselling process, the option of a prenatal screening test for the most common clinically significant fetal aneuploidies in addition to a second trimester ultrasound for dating, assessment of fetal anatomy, and detection of multiples. (I-A) 2. Counselling must be non-directive and must respect a woman's right to accept or decline any or all of the testing or options offered at any point in the process. (III-A) 3. Maternal age alone is a poor minimum standard for prenatal screening

The challenge of screen printed Ag metallization on nano-scale poly-silicon passivated contacts for silicon solar cells

Science.gov (United States)

Jiang, Lin; Song, Lixin; Yan, Li; Becht, Gregory; Zhang, Yi; Hoerteis, Matthias

2017-08-01

Passivated contacts can be used to reduce metal-induced recombination for higher energy conversion efficiency for silicon solar cells, and are obtained increasing attentions by PV industries in recent years. The reported thicknesses of passivated contact layers are mostly within tens of nanometer range, and the corresponding metallization methods are realized mainly by plating/evaporation technology. This high cost metallization cannot compete with the screen printing technology, and may affect its market potential comparing with the presently dominant solar cell technology. Very few works have been reported on screen printing metallization on passivated contact solar cells. Hence, there is a rising demand to realize screen printing metallization technology on this topic. In this work, we investigate applying screen printing metallization pastes on poly-silicon passivated contacts. The critical challenge for us is to build low contact resistance that can be competitive to standard technology while restricting the paste penetrations within the thin nano-scale passivated contact layers. The contact resistivity of 1.1mohm-cm2 and the open circuit voltages > 660mV are achieved, and the most appropriate thickness range is estimated to be around 80 150nm.

Communication between a Matrix Converter Modulator and a Superset Regulator

Directory of Open Access Journals (Sweden)

P. Pošta

2008-01-01

Full Text Available This work deals with the modulator of a matrix converter and its communication with the superset regulator. A switching algorithm is briefly introduced. The input voltage measurement method is presented. In the last part of the paper, the testing of communication between the superset regulator and the modulator in FPGA technology are also presented. 

Total-body photography in skin cancer screening: the clinical utility of standardized imaging.

Science.gov (United States)

Rosenberg, Alexandra; Meyerle, Jon H

2017-05-01

Early detection of skin cancer is essential to reducing morbidity and mortality from both melanoma and nonmelanoma skin cancers. Total-body skin examinations (TBSEs) may improve early detection of malignant melanomas (MMs) but are controversial due to the poor quality of data available to establish a mortality benefit from skin cancer screening. Total-body photography (TBP) promises to provide a way forward by lowering the costs of dermatologic screening while simultaneously leveraging technology to increase patient access to dermatologic care. Standardized TBP also offers the ability for dermatologists to work synergistically with modern computer technology involving algorithms capable of analyzing high-quality images to flag concerning lesions that may require closer evaluation. On a population level, inexpensive TBP has the potential to increase access to skin cancer screening and it has several specific applications in a military population. The utility of standardized TBP is reviewed in the context of skin cancer screening and teledermatology.

Fast Enrichment Screening for Safeguards Applications

International Nuclear Information System (INIS)

Simpson, A.; McElhaney, S.

2010-01-01

Methods for rapid non-destructive uranium enrichment classification of large containers are of importance to safeguards and counter-terrorism agencies. There is a need to quickly categorize and segregate suspect items as 'depleted' or 'enriched' on a 'Go/No Go' basis. Recent improvements in gamma spectroscopy technologies have provided the capability to perform rapid field analysis using portable and hand-held devices such as battery-operated medium and high resolution detectors (including lanthanum halide and high purity germanium). Furthermore a new generation of portal monitors are currently under development with advanced spectroscopic capabilities. Instruments and technologies that were previously the domain of complex lab systems are now widely available as touch-screen 'off-the-shelf' units. Despite such advances, the task of enrichment analysis remains a complex exercise. This is particularly so when surveying large items such as drums and crates containing debris of unknown density and composition contaminated with uranium. The challenge is equally applicable to safeguards inspectors evaluating large items and for interdiction of illicit special nuclear materials in mass transport e.g. shipping containers at ports and borders. The variable shielding, container size, lack of matrix knowledge, wall thickness and self-shielding compound this problem. Performing an accurate assessment within the short count time window demanded of the field operative, leads to the need for a reliable method that can adapt to such conditions and is robust to a wide dynamic range of counting statistics. Several methods are evaluated with reference to the performance metrics defined in applicable standards. The primary issue is to minimize the bias that can result from attenuation effects, particularly as the gamma emissions from U235 are low energy and therefore highly susceptible to absorption in large containers with metal scrap. Use of other radiometric signatures such as

Matrix effect in the analysis of drugs of abuse from urine with desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS) and desorption electrospray ionization-mass spectrometry (DESI-MS)

International Nuclear Information System (INIS)

Suni, Niina M.; Lindfors, Pia; Laine, Olli; Ostman, Pekka; Ojanperae, Ilkka; Kotiaho, Tapio; Kauppila, Tiina J.; Kostiainen, Risto

2011-01-01

Highlights: → DAPPI-MS and DESI-MSI in the analysis of drugs of abuse from urine. → DAPPI-MS has better urine matrix tolerance over DESI-MS. → Urine matrix can affect the ionization mechanism in DAPPI. → DAPPI-MS/MS can be used for screening of drugs from urine after sample pretreatment. - Abstract: We have studied the matrix effect within direct analysis of benzodiazepines and opioids from urine with desorption electrospray ionization-mass spectrometry (DESI-MS) and desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS). The urine matrix was found to affect the ionization mechanism of the opioids in DAPPI-MS favoring proton transfer over charge exchange reaction. The sensitivity for the drugs in solvent matrix was at the same level with DESI-MS and DAPPI-MS (LODs 0.05-6 μg mL -1 ) but the decrease in sensitivity due to the urine matrix was higher with DESI (typically 20-160-fold) than with DAPPI (typically 2-15-fold) indicating better matrix tolerance of DAPPI over DESI. Also in MS/MS mode, DAPPI provided better sensitivity than DESI for the drugs in urine. The feasibility of DAPPI-MS/MS was then studied in screening the same drugs from five authentic, forensic post mortem urine samples. A reference measurement with gas chromatography-mass spectrometry (GC-MS) (including pretreatment) revealed 16 findings from the samples, whereas with DAPPI-MS/MS after sample pretreatment, 15 findings were made. Sample pretreatment was found necessary, since only eight findings were made from the same samples untreated.

Matrix effect in the analysis of drugs of abuse from urine with desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS) and desorption electrospray ionization-mass spectrometry (DESI-MS)

Energy Technology Data Exchange (ETDEWEB)

Suni, Niina M.; Lindfors, Pia; Laine, Olli [Division of Pharmaceutical Chemistry, University of Helsinki, P.O. Box 56, Helsinki FI-00014 (Finland); Ostman, Pekka; Ojanperae, Ilkka [Hjelt Institute, Department of Forensic Medicine, University of Helsinki, P.O. Box 40, Helsinki FI-00014 (Finland); Kotiaho, Tapio [Division of Pharmaceutical Chemistry, University of Helsinki, P.O. Box 56, Helsinki FI-00014 (Finland); Laboratory of Analytical Chemistry, Department of Chemistry, University of Helsinki, P.O. Box 55, Helsinki FI-00014 (Finland); Kauppila, Tiina J. [Division of Pharmaceutical Chemistry, University of Helsinki, P.O. Box 56, Helsinki FI-00014 (Finland); Kostiainen, Risto, E-mail: risto.kostiainen@helsinki.fi [Division of Pharmaceutical Chemistry, University of Helsinki, P.O. Box 56, Helsinki FI-00014 (Finland)

2011-08-05

Highlights: {yields} DAPPI-MS and DESI-MSI in the analysis of drugs of abuse from urine. {yields} DAPPI-MS has better urine matrix tolerance over DESI-MS. {yields} Urine matrix can affect the ionization mechanism in DAPPI. {yields} DAPPI-MS/MS can be used for screening of drugs from urine after sample pretreatment. - Abstract: We have studied the matrix effect within direct analysis of benzodiazepines and opioids from urine with desorption electrospray ionization-mass spectrometry (DESI-MS) and desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS). The urine matrix was found to affect the ionization mechanism of the opioids in DAPPI-MS favoring proton transfer over charge exchange reaction. The sensitivity for the drugs in solvent matrix was at the same level with DESI-MS and DAPPI-MS (LODs 0.05-6 {mu}g mL{sup -1}) but the decrease in sensitivity due to the urine matrix was higher with DESI (typically 20-160-fold) than with DAPPI (typically 2-15-fold) indicating better matrix tolerance of DAPPI over DESI. Also in MS/MS mode, DAPPI provided better sensitivity than DESI for the drugs in urine. The feasibility of DAPPI-MS/MS was then studied in screening the same drugs from five authentic, forensic post mortem urine samples. A reference measurement with gas chromatography-mass spectrometry (GC-MS) (including pretreatment) revealed 16 findings from the samples, whereas with DAPPI-MS/MS after sample pretreatment, 15 findings were made. Sample pretreatment was found necessary, since only eight findings were made from the same samples untreated.

Development and characterization of a snapshot Mueller matrix polarimeter for the determination of cervical cancer risk in the low resource setting

Science.gov (United States)

Ramella-Roman, Jessica C.; Gonzalez, Mariacarla; Chue-Sang, Joseph; Montejo, Karla; Krup, Karl; Srinivas, Vijaya; DeHoog, Edward; Madhivanan, Purnima

2018-04-01

Mueller Matrix polarimetry can provide useful information about the function and structure of the extracellular matrix. Mueller Matrix systems are sophisticated and costly optical tools that have been used primarily in the laboratory or in hospital settings. Here we introduce a low-cost snapshot Mueller Matrix polarimeter that that does not require external power, has no moving parts, and can acquire a full Mueller Matrix in less than 50 milliseconds. We utilized this technology in the study of cervical cancer in Mysore India, yet the system could be translated in multiple diagnostic applications.

Wear study of Al-SiC metal matrix composites processed through microwave energy

Science.gov (United States)

Honnaiah, C.; Srinath, M. S.; Prasad, S. L. Ajit

2018-04-01

Particulate reinforced metal matrix composites are finding wider acceptance in many industrial applications due to their isotropic properties and ease of manufacture. Uniform distribution of reinforcement particulates and good bonding between matrix and reinforcement phases are essential features in order to obtain metal matrix composites with improved properties. Conventional powder metallurgy technique can successfully overcome the limitation of stir casting techniques, but it is time consuming and not cost effective. Use of microwave technology for processing particulate reinforced metal matrix composites through powder metallurgy technique is being increasingly explored in recent times because of its cost effectiveness and speed of processing. The present work is an attempt to process Al-SiC metal matrix composites using microwaves irradiated at 2.45 GHz frequency and 900 W power for 10 minutes. Further, dry sliding wear studies were conducted at different loads at constant velocity of 2 m/s for various sliding distances using pin-on-disc equipment. Analysis of the obtained results show that the microwave processed Al-SiC composite material shows around 34 % of resistance to wear than the aluminium alloy.

Epidemiology, aetiology, diagnosis and screening of lung cancer

International Nuclear Information System (INIS)

Berzinec, P.

2006-01-01

Lung cancer is the leading cause of cancer death globally. Smoking causes about 90 % of all lung cancer cases. Passive, i.e. involuntary smoking has been confirmed to enhance the risk of lung cancer in exposed people. Individual susceptibility is one of important factors in lung cancer formation. New knowledge in epidemiology and aetiology of lung cancer gives new possibilities in diagnostic and screening of this disease. Results of large randomised trials aimed at new technologies in lung cancer screening will be available in a few years. (author)

Matrix metalloproteinase-2 gene variants and abdominal aortic aneurysm.

Science.gov (United States)

Smallwood, L; Warrington, N; Allcock, R; van Bockxmeer, F; Palmer, L J; Iacopetta, B; Golledge, J; Norman, P E

2009-08-01

To investigate associations between two polymorphisms of the matrix metalloproteinase-2 gene (MMP2) and the incidence and progression of abdominal aortic aneurysm (AAA). Cases and controls were recruited from a trial of screening for AAAs. The association between two variants of MMP2 (-1360C>T, and +649C>T) in men with AAA (n=678) and in controls (n=659) was examined using multivariate analyses. The association with AAA expansion (n=638) was also assessed. In multivariate analyses with adjustments for multiple testing, no association between either SNP and AAA presence or expansion was detected. MMP2 -1360C>T and +649C>T variants are not risk factors for AAA.

Screen printed thick film based pMUT arrays

DEFF Research Database (Denmark)

Hedegaard, Tobias; Pedersen, T; Thomsen, Erik Vilain

2008-01-01

This article reports on the fabrication and characterization of lambda-pitched piezoelectric micromachined ultrasound transducer (pMUT) arrays fabricated using a unique process combining conventional silicon technology and low cost screen printing of thick film PZT. The pMUTs are designed as 8...

Fiscal 1991-1993 summary report on R and D on new forming technology of composite materials; Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu 1991 nendo - 1993 nendo sokatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

Developed were the materials which can be easily formed by manifesting superplasticity simultaneously with high toughness and high strength through selection of material composition and micronizing of the structure, in regard to composite materials answering to high strength and resistance to high temperature suitable for engines or the like. Developed for ceramic matrix composite materials were composite technology of silicon nitride matrix composites by a casting method, composite technology of Al{sub 2}O{sub 3}/TiC matrix composites by a material preparation method using aqueous slurry, and superplastic forming technology of yttria stabilized zirconia/alumina matrix composites; developed for metallic matrix composite materials were composite technology of reinforced ceramics particulate aluminum alloy matrix composites by a voltex method, composite technology of ceramic short fibers reinforced aluminum alloy composites by a high pressure casting method under reduced pressure, composite technology of titanium matrix composites by a mechanical alloying method, and composite technology of aluminum alloy composites by ceramics particles, superplastic forming technology of SiC whisker reinforced aluminum alloy reinforced composites, and superplastic forming technology of aluminum alloy matrix reinforced composites reinforced by SiC particles. (NEDO)

Evaluating the use of mobile phone technology to enhance cardiovascular disease screening by community health workers.

Science.gov (United States)

Surka, Sam; Edirippulige, Sisira; Steyn, Krisela; Gaziano, Thomas; Puoane, Thandi; Levitt, Naomi

2014-09-01

Primary prevention of cardiovascular disease (CVD),by identifying individuals at risk is a well-established, but costly strategy when based on measurements that depend on laboratory analyses. A non-laboratory, paper-based CVD risk assessment chart tool has previously been developed to make screening more affordable in developing countries. Task shifting to community health workers (CHWs) is being investigated to further scale CVD risk screening. This study aimed to develop a mobile phone CVD risk assessment application and to evaluate its impact on CHW training and the duration of screening for CVD in the community by CHWs. A feature phone application was developed using the open source online platform, CommCare(©). CHWs (n=24) were trained to use both paper-based and mobile phone CVD risk assessment tools. They were randomly allocated to using one of the risk tools to screen 10-20 community members and then crossed over to screen the same number, using the alternate risk tool. The impact on CHW training time, screening time and margin of error in calculating risk scores was recorded. A focus group discussion evaluated experiences of CHWs using the two tools. The training time was 12.3h for the paper-based chart tool and 3h for the mobile phone application. 537 people were screened. The mean screening time was 36 min (SD=12.6) using the paper-base chart tool and 21 min (SD=8.71) using the mobile phone application, p=mobile phone calculations were correct. Qualitative findings from the focus group discussion corresponded with the findings of the pilot study. The reduction in CHW training time, CVD risk screening time, lack of errors in calculation of a CVD risk score and end user satisfaction when using a mobile phone application, has implications in terms of adoption and sustainability of this primary prevention strategy to identify people with high CVD risk who can be referred for appropriate diagnoses and treatment. Copyright © 2014 Elsevier Ireland Ltd. All

Fuzzy risk matrix

International Nuclear Information System (INIS)

Markowski, Adam S.; Mannan, M. Sam

2008-01-01

A risk matrix is a mechanism to characterize and rank process risks that are typically identified through one or more multifunctional reviews (e.g., process hazard analysis, audits, or incident investigation). This paper describes a procedure for developing a fuzzy risk matrix that may be used for emerging fuzzy logic applications in different safety analyses (e.g., LOPA). The fuzzification of frequency and severity of the consequences of the incident scenario are described which are basic inputs for fuzzy risk matrix. Subsequently using different design of risk matrix, fuzzy rules are established enabling the development of fuzzy risk matrices. Three types of fuzzy risk matrix have been developed (low-cost, standard, and high-cost), and using a distillation column case study, the effect of the design on final defuzzified risk index is demonstrated

The Extracellular Matrix Regulates Granuloma Necrosis in Tuberculosis.

Science.gov (United States)

Al Shammari, Basim; Shiomi, Takayuki; Tezera, Liku; Bielecka, Magdalena K; Workman, Victoria; Sathyamoorthy, Tarangini; Mauri, Francesco; Jayasinghe, Suwan N; Robertson, Brian D; D'Armiento, Jeanine; Friedland, Jon S; Elkington, Paul T

2015-08-01

A central tenet of tuberculosis pathogenesis is that caseous necrosis leads to extracellular matrix destruction and bacterial transmission. We reconsider the underlying mechanism of tuberculosis pathology and demonstrate that collagen destruction may be a critical initial event, causing caseous necrosis as opposed to resulting from it. In human tuberculosis granulomas, regions of extracellular matrix destruction map to areas of caseous necrosis. In mice, transgenic expression of human matrix metalloproteinase 1 causes caseous necrosis, the pathological hallmark of human tuberculosis. Collagen destruction is the principal pathological difference between humanised mice and wild-type mice with tuberculosis, whereas the release of proinflammatory cytokines does not differ, demonstrating that collagen breakdown may lead to cell death and caseation. To investigate this hypothesis, we developed a 3-dimensional cell culture model of tuberculosis granuloma formation, using bioelectrospray technology. Collagen improved survival of Mycobacterium tuberculosis-infected cells analyzed on the basis of a lactate dehydrogenase release assay, propidium iodide staining, and measurement of the total number of viable cells. Taken together, these findings suggest that collagen destruction is an initial event in tuberculosis immunopathology, leading to caseous necrosis and compromising the immune response, revealing a previously unappreciated role for the extracellular matrix in regulating the host-pathogen interaction. © The Author 2015. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Patterning of PMMA microfluidic parts using screen printing process

Science.gov (United States)

Ahari Kaleibar, Aminreza; Rahbar, Mona; Haiducu, Marius; Parameswaran, Ash M.

2010-02-01

An inexpensive and rapid micro-fabrication process for producing PMMA microfluidic components has been presented. Our proposed technique takes advantages of commercially available economical technologies such as the silk screen printing and UV patterning of PMMA substrates to produce the microfluidic components. As a demonstration of our proposed technique, we had utilized a homemade deep-UV source, λ=254nm, a silk screen mask made using a local screen-printing shop and Isopropyl alcohol - water mixture (IPA-water) as developer to quickly define the microfluidic patterns. The prototyped devices were successfully bonded, sealed, and the device functionality tested and demonstrated. The screen printing based technique can produce microfluidic channels as small as 50 micrometers quite easily, making this technique the most cost-effective, fairly high precision and at the same time an ultra economical plastic microfluidic components fabrication process reported to date.

Efficiency evaluation for remediating paddy soil contaminated with cadmium and arsenic using water management, variety screening and foliage dressing technologies.

Science.gov (United States)

Liao, Guojian; Wu, Qianhua; Feng, Renwei; Guo, Junkang; Wang, Ruigang; Xu, Yingming; Ding, Yongzhen; Fan, Zhilian; Mo, Liangyu

2016-04-01

Paddy soils in many regions of China have been seriously polluted by multiple heavy metals or metalloids, such as arsenic (As), cadmium (Cd) and lead (Pb). In order to ensure the safety of food and take full advantage of the limited farmland resources of China, exploring an effective technology to repair contaminated soils is urgent and necessary. In this study, three technologies were employed, including variety screening, water management and foliage dressing, to assess their abilities to reduce the accumulation of Cd and As in the grains of different rice varieties, and meanwhile monitor the related yields. The results of variety screening under insufficient field drying condition showed that the As and Cd contents in the grains of only four varieties [Fengliangyouxiang 1 (P6), Zhongzheyou 8 (P7), Guangliangyou 1128 (P10), Y-liangyou 696 (P11)] did not exceed their individual national standard. P6 gained a relatively high grain yield but accumulated less As and Cd in the grains despite of the relatively high As and Cd concentrations in the rhizosphere soil. However, long-playing field drying in water management trial significantly increased Cd but decreased As content in the grains of all tested three varieties including P6, suggesting an important role of water supply in controlling the accumulation of grain As and Cd. Selenium (Se) showed a stronger ability than silicon (Si) to reduce As and Cd accumulation in the grains of Fengliangyou 4 (P2) and Teyou 524 (P13), and keep the yields. The results of this study suggest that combined application of water management and foliage dressing may be an efficient way to control As and Cd accumulation in the grains of paddy rice exposing to As- and Cd-contaminated soils. Copyright © 2016 Elsevier Ltd. All rights reserved.

Adherence of extracellular matrix components to modified surfaces of titanium alloys

International Nuclear Information System (INIS)

Stelzer, C; Uhlmann, E; Meinke, M; Lademann, J; Hansen, U

2009-01-01

The adherence of biological materials on metal surfaces is of special importance in biology and medicine. The underlying interactions between surface and biological materials (e.g. extracellular matrix components or cells) are responsible for the application as a medical device. Numerous products are made of pure titanium and titanium alloys. This paper shows the influence of a laser production technology on machined surfaces of TiAl 6 V 4 and the resulting adherence of biological material on the basis of the surface characterisation. In this study, different machined TiAl 6 V 4 surfaces were used for coatings with extracellular matrix components. For this process, different coating with collagen I monomers and a complex mixture of extracellular matrix proteins derived from the dermal-epidermal basement membrane zone were analysed. The efficiency of the coating was analysed by different methods and the results are presented in this paper

Current role of liquid chromatography coupled to mass spectrometry in clinical toxicology screening methods.

Science.gov (United States)

Viette, Véronique; Fathi, Marc; Rudaz, Serge; Hochstrasser, Denis; Veuthey, Jean-Luc

2011-07-01

Abstract Toxicological screening is the analysis of a biological specimen to detect and identify compounds in patients admitted to the hospital with acute intoxication of unknown origin. The screening of a wide range of toxicologically relevant compounds in biological samples is a serious challenge for clinical laboratories. The high selectivity and sensitivity of liquid chromatography coupled to mass spectrometry or tandem mass spectrometry technology provides an attractive alternative to the current methods. For these reasons, an increasing number of applications for multi-target screening or general screening of unknown compounds in biological matrices are being published. This paper is an overview of sample clean-up, chromatographic separation and mass spectrometry detection procedures which can be combined to obtain screening methods adapted to the constraints and needs of various laboratories, and none specifically in clinical toxicology. Currently the techniques are in the hands of specialists, principally in academic institutes. However, the evolution in technology should allow application of the techniques as a tool in toxicology laboratories and thus more widespread exploitation of their potential.

High-quality and small-capacity e-learning video featuring lecturer-superimposing PC screen images

Science.gov (United States)

Nomura, Yoshihiko; Murakami, Michinobu; Sakamoto, Ryota; Sugiura, Tokuhiro; Matsui, Hirokazu; Kato, Norihiko

2006-10-01

Information processing and communication technology are progressing quickly, and are prevailing throughout various technological fields. Therefore, the development of such technology should respond to the needs for improvement of quality in the e-learning education system. The authors propose a new video-image compression processing system that ingeniously employs the features of the lecturing scene. While dynamic lecturing scene is shot by a digital video camera, screen images are electronically stored by a PC screen image capturing software in relatively long period at a practical class. Then, a lecturer and a lecture stick are extracted from the digital video images by pattern recognition techniques, and the extracted images are superimposed on the appropriate PC screen images by off-line processing. Thus, we have succeeded to create a high-quality and small-capacity (HQ/SC) video-on-demand educational content featuring the advantages: the high quality of image sharpness, the small electronic file capacity, and the realistic lecturer motion.

Molecular dynamics simulations of matrix assisted laser desorption ionization: Matrix-analyte interactions

International Nuclear Information System (INIS)

Nangia, Shivangi; Garrison, Barbara J.

2011-01-01

There is synergy between matrix assisted laser desorption ionization (MALDI) experiments and molecular dynamics (MD) simulations. To understand analyte ejection from the matrix, MD simulations have been employed. Prior calculations show that the ejected analyte molecules remain solvated by the matrix molecules in the ablated plume. In contrast, the experimental data show free analyte ions. The main idea of this work is that analyte molecule ejection may depend on the microscopic details of analyte interaction with the matrix. Intermolecular matrix-analyte interactions have been studied by focusing on 2,5-dihydroxybenzoic acid (DHB; matrix) and amino acids (AA; analyte) using Chemistry at HARvard Molecular Mechanics (CHARMM) force field. A series of AA molecules have been studied to analyze the DHB-AA interaction. A relative scale of AA molecule affinity towards DHB has been developed.

When technological affordances meet interactional norms: the value of pre-screening in online chat counseling

NARCIS (Netherlands)

Stommel, Wyke; te Molder, Hedwig Frederica Maria

2016-01-01

We present a conversation analysis of openings sequences of online text-based chat counseling. Particular about this chat counseling is that the clients made available their help question through pre-screening. The data consisted of 40 chat sessions with pre-screening and 34 sessions without

ScreenBEAM: a novel meta-analysis algorithm for functional genomics screens via Bayesian hierarchical modeling | Office of Cancer Genomics

Science.gov (United States)

Functional genomics (FG) screens, using RNAi or CRISPR technology, have become a standard tool for systematic, genome-wide loss-of-function studies for therapeutic target discovery. As in many large-scale assays, however, off-target effects, variable reagents' potency and experimental noise must be accounted for appropriately control for false positives.

The sintered microsphere matrix for bone tissue engineering: in vitro osteoconductivity studies.

Science.gov (United States)

Borden, Mark; Attawia, Mohamed; Laurencin, Cato T

2002-09-05

A tissue engineering approach has been used to design three-dimensional synthetic matrices for bone repair. The osteoconductivity and degradation profile of a novel polymeric bone-graft substitute was evaluated in an in vitro setting. Using the copolymer poly(lactide-co-glycolide) [PLAGA], a sintering technique based on microsphere technology was used to fabricate three-dimensional porous scaffolds for bone regeneration. Osteoblasts and fibroblasts were seeded onto a 50:50 PLAGA scaffold. Morphologic evaluation through scanning electron microscopy demonstrated that both cell types attached and spread over the scaffold. Cells migrated through the matrix using cytoplasmic extensions to bridge the structure. Cross-sectional images indicated that cellular proliferation had penetrated into the matrix approximately 700 microm from the surface. Examination of the surfaces of cell/matrix constructs demonstrated that cellular proliferation had encompassed the pores of the matrix by 14 days of cell culture. With the aim of optimizing polymer composition and polymer molecular weight, a degradation study was conducted utilizing the matrix. The results demonstrate that degradation of the sintered matrix is dependent on molecular weight, copolymer ratio, and pore volume. From this data, it was determined that 75:25 PLAGA with an initial molecular weight of 100,000 has an optimal degradation profile. These studies show that the sintered microsphere matrix has an osteoconductive structure capable of functioning as a cellular scaffold with a degradation profile suitable for bone regeneration. Copyright 2002 Wiley Periodicals, Inc.

Developing a novel fiber optic fluorescence device for multiplexed high-throughput cytotoxic screening.

Science.gov (United States)

Lee, Dennis; Barnes, Stephen

2010-01-01

The need for new pharmacological agents is unending. Yet the drug discovery process has changed substantially over the past decade and continues to evolve in response to new technologies. There is presently a high demand to reduce discovery time by improving specific lab disciplines and developing new technology platforms in the area of cell-based assay screening. Here we present the developmental concept and early stage testing of the Ab-Sniffer, a novel fiber optic fluorescence device for high-throughput cytotoxicity screening using an immobilized whole cell approach. The fused silica fibers are chemically functionalized with biotin to provide interaction with fluorescently labeled, streptavidin functionalized alginate-chitosan microspheres. The microspheres are also functionalized with Concanavalin A to facilitate binding to living cells. By using lymphoma cells and rituximab in an adaptation of a well-known cytotoxicity protocol we demonstrate the utility of the Ab-Sniffer for functional screening of potential drug compounds rather than indirect, non-functional screening via binding assay. The platform can be extended to any assay capable of being tied to a fluorescence response including multiple target cells in each well of a multi-well plate for high-throughput screening.

Thermal and mechanical behavior of metal matrix and ceramic matrix composites

Science.gov (United States)

Kennedy, John M. (Editor); Moeller, Helen H. (Editor); Johnson, W. S. (Editor)

1990-01-01

The present conference discusses local stresses in metal-matrix composites (MMCs) subjected to thermal and mechanical loads, the computational simulation of high-temperature MMCs' cyclic behavior, an analysis of a ceramic-matrix composite (CMC) flexure specimen, and a plasticity analysis of fibrous composite laminates under thermomechanical loads. Also discussed are a comparison of methods for determining the fiber-matrix interface frictional stresses of CMCs, the monotonic and cyclic behavior of an SiC/calcium aluminosilicate CMC, the mechanical and thermal properties of an SiC particle-reinforced Al alloy MMC, the temperature-dependent tensile and shear response of a graphite-reinforced 6061 Al-alloy MMC, the fiber/matrix interface bonding strength of MMCs, and fatigue crack growth in an Al2O3 short fiber-reinforced Al-2Mg matrix MMC.

Prenatal screening, diagnosis, and pregnancy management of fetal neural tube defects.

Science.gov (United States)

Wilson, R Douglas

2014-10-01

To provide obstetrical and genetic health care practitioners with guidelines and recommendations for prenatal screening, diagnosis, and obstetrical management of fetal open and closed neural tube defects (OCNTD). This review includes prenatal screening and diagnostic techniques currently being used for the detection of OCNTD including maternal serum alpha fetoprotein screening, ultrasound, fetal magnetic resonance imaging, and amniocentesis. To improve prenatal screening, diagnosis, and obstetrical management of OCNTD while taking into consideration patient care, efficacy, cost, and care procedures. Published literature was retrieved through searches of PubMed or MEDLINE, CINAHL, and The Cochrane Library in November, 2013, using appropriate controlled vocabulary and key words (e.g., prenatal screening, congenital anomalies, neural tube defects, alpha fetoprotein, ultrasound scan, magnetic resonance imaging). Results were restricted to systematic reviews, randomized control trials/controlled clinical trials, and observational studies published in English from 1977 to 2012. Searches were updated on a regular basis and incorporated in the guideline to November 30, 2013. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. An online survey of health care practitioners was also reviewed. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table). This review will provide health care practitioners with a better understanding of the available prenatal screening methods for OCNTD and the benefits and risks associated with each technique to allow evidenced-based decisions on OCNTD screening, diagnosis, and obstetrical management.

High throughput screening of starch structures using carbohydrate microarrays

DEFF Research Database (Denmark)

Tanackovic, Vanja; Rydahl, Maja Gro; Pedersen, Henriette Lodberg

2016-01-01

In this study we introduce the starch-recognising carbohydrate binding module family 20 (CBM20) from Aspergillus niger for screening biological variations in starch molecular structure using high throughput carbohydrate microarray technology. Defined linear, branched and phosphorylated...

Study of ionization process of matrix molecules in matrix-assisted laser desorption ionization

Energy Technology Data Exchange (ETDEWEB)

Murakami, Kazumasa; Sato, Asami; Hashimoto, Kenro; Fujino, Tatsuya, E-mail: fujino@tmu.ac.jp

2013-06-20

Highlights: ► Proton transfer and adduction reaction of matrix in MALDI were studied. ► Hydroxyl group forming intramolecular hydrogen bond was related to the ionization. ► Intramolecular proton transfer in the electronic excited state was the initial step. ► Non-volatile analytes stabilized protonated matrix in the ground state. ► A possible mechanism, “analyte support mechanism”, has been proposed. - Abstract: Proton transfer and adduction reaction of matrix molecules in matrix-assisted laser desorption ionization were studied. By using 2,4,6-trihydroxyacetophenone (THAP), 2,5-dihydroxybenzoic acid (DHBA), and their related compounds in which the position of a hydroxyl group is different, it was clarified that a hydroxyl group forming an intramolecular hydrogen bond is related to the ionization of matrix molecules. Intramolecular proton transfer in the electronic excited state of the matrix and subsequent proton adduction from a surrounding solvent to the charge-separated matrix are the initial steps for the ionization of matrix molecules. Nanosecond pump–probe NIR–UV mass spectrometry confirmed that the existence of analyte molecules having large dipole moment in their structures is necessary for the stabilization of [matrix + H]{sup +} in the electronic ground state.

Coherence and Polarization of Polarization Speckle Generated by Depolarizers and Their Changes through Complex ABCD Matrix

DEFF Research Database (Denmark)

Ma, Ning; Hanson, Steen Grüner; Lee, Tim K.

2015-01-01

Recent research work on speckle patterns indicates a variation of the polarization state during propagation and its nonuniformly spatial distribution. The preliminary step for the investigation of this polarization speckle is the generation of the corresponding field. In this paper, a kind...... of special depolarizer: the random roughness birefringent screen (RRBS) is introduced to meet this requirement. The statistical properties of the field generated by the depolarizer is investigated and illustrated in terms of the 2x2 beam coherence and polarization matrix (BCPM) with the corresponding degree...... of coherence (DoC). and degree of polarization (DoP) P. The changes of the coherence and polarization when the speckle field propagates through any optical system are analysed within the framework of the complex ABCD-matrix theory....

A Human Nuclear Shuttling Protein That Interacts with Human Immunodeficiency Virus Type 1 Matrix Is Packaged into Virions

Science.gov (United States)

Gupta, Kalpana; Ott, David; Hope, Thomas J.; Siliciano, Robert F.; Boeke, Jef D.

2000-01-01

Active nuclear import of the human immunodeficiency virus type 1 (HIV-1) preintegration complex (PIC) is essential for the productive infection of nondividing cells. Nuclear import of the PIC is mediated by the HIV-1 matrix protein, which also plays several critical roles during viral entry and possibly during virion production facilitating the export of Pr55Gag and genomic RNA. Using a yeast two-hybrid screen, we identified a novel human virion-associated matrix-interacting protein (VAN) that is highly conserved in vertebrates and expressed in most human tissues. Its expression is upregulated upon activation of CD4+ T cells. VAN is efficiently incorporated into HIV-1 virions and, like matrix, shuttles between the nucleus and cytoplasm. Furthermore, overexpression of VAN significantly inhibits HIV-1 replication in tissue culture. We propose that VAN regulates matrix nuclear localization and, by extension, both nuclear import of the PIC and export of Pr55Gag and viral genomic RNA during virion production. Our data suggest that this regulatory mechanism reflects a more global process for regulation of nucleocytoplasmic transport. PMID:11090181

Investigating the incremental validity of cognitive variables in early mathematics screening.

Science.gov (United States)

Clarke, Ben; Shanley, Lina; Kosty, Derek; Baker, Scott K; Cary, Mari Strand; Fien, Hank; Smolkowski, Keith

2018-03-26

The purpose of this study was to investigate the incremental validity of a set of domain general cognitive measures added to a traditional screening battery of early numeracy measures. The sample consisted of 458 kindergarten students of whom 285 were designated as severely at-risk for mathematics difficulty. Hierarchical multiple regression results indicated that Wechsler Abbreviated Scales of Intelligence (WASI) Matrix Reasoning and Vocabulary subtests, and Digit Span Forward and Backward measures explained a small, but unique portion of the variance in kindergarten students' mathematics performance on the Test of Early Mathematics Ability-Third Edition (TEMA-3) when controlling for Early Numeracy Curriculum Based Measurement (EN-CBM) screening measures (R² change = .01). Furthermore, the incremental validity of the domain general cognitive measures was relatively stronger for the severely at-risk sample. We discuss results from the study in light of instructional decision-making and note the findings do not justify adding domain general cognitive assessments to mathematics screening batteries. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Fabricating high-resolution offset color-filter black matrix by integrating heterostructured substrate with inkjet printing

International Nuclear Information System (INIS)

Lu, Guo-Shin; You, Po-Chin; Lin, Kai-Lun; Hong, Chien-Chong; Liou, Tong-Miin

2014-01-01

This paper presents a self-aligning ink by integrating an inkjet printing technique and heterostructures to fabricate a black matrix with a micrometer-scale tunable thickness. The black matrix is a grid-like structure used in color filters. Traditionally, a black matrix has been fabricated using photolithography techniques, the disadvantages of which are high material consumption, less fabrication flexibility, complex processing procedures, and high chemical pollution. Inkjet printing technology has garnered attention because of its low material costs, high fabrication flexibility, and reduced processing procedures and pollution. In this study, a fabricating process combining an inkjet printing technique with heterostructures to form stripe-arranged and delta-arranged thickness-tunable black matrices has been demonstrated. The deformation and self-aligning process of ink droplet impingement onto gutters are driven by designed heterogeneous surface properties. The minimum track width attained is 10 µm, which is competitive for color filter resolutions for thin-film transistor liquid crystal displays. The developed technology surmounts the bottlenecks of inkjet printing resolution, and saves more than 75% black material than modern photolithography. (paper)

Screens

OpenAIRE

2016-01-01

This Sixth volume in the series The Key Debates. Mutations and Appropriations in European Film Studies investigates the question of screens in the context both of the dematerialization due to digitalization and the multiplication of media screens. Scholars offer various infomations and theories of topics such as the archeology of screen, film and media theories, contemporary art, pragmatics of new ways of screening (from home video to street screening).

Application of chemical arrays in screening elastase inhibitors.

Science.gov (United States)

Gao, Feng; Du, Guan-Hua

2006-06-01

Protein chip technology provides a new and useful tool for high-throughput screening of drugs because of its high performance and low sample consumption. In order to screen elastase inhibitors on a large scale, we designed a composite microarray integrating enzyme chip containing chemical arrays on glass slides to screen for enzymatic inhibitors. The composite microarray includes an active proteinase film, screened chemical arrays distributed on the film, and substrate microarrays to demonstrate change of color. The detection principle is that elastase hydrolyzes synthetic colorless substrates and turns them into yellow products. Because yellow is difficult to detect, bromochlorophenol blue (BPB) was added into substrate solutions to facilitate the detection process. After the enzyme had catalyzed reactions for 2 h, effects of samples on enzymatic activity could be determined by detecting color change of the spots. When chemical samples inhibited enzymatic activity, substrates were blue instead of yellow products. If the enzyme retained its activity, the yellow color of the products combined with blue of BPB to make the spots green. Chromogenic differences demonstrated whether chemicals inhibited enzymatic activity or not. In this assay, 11,680 compounds were screened, and two valuable chemical hits were identified, which demonstrates that this assay is effective, sensitive and applicable for high-throughput screening (HTS).

Genomic futures of prenatal screening: ethical reflection.

Science.gov (United States)

Dondorp, W J; Page-Christiaens, G C M L; de Wert, G M W R

2016-05-01

The practice of prenatal screening is undergoing important changes as a result of the introduction of genomic testing technologies at different stages of the screening trajectory. It is expected that eventually it will become possible to routinely obtain a comprehensive 'genome scan' of all fetuses. Although this will still take several years, there are clear continuities between present developments and this future scenario. As this review shows, behind the still limited scope of screening for common aneuploidies, a rapid widening of the range of conditions tested for is already taking shape at the invasive testing stage. But the continuities are not just technical; they are also ethical. If screening for Down's syndrome is a matter of providing autonomous reproductive choice, then why would providing the choice to have a full fetal genome scan be something entirely different? There is a clear need for a sustainable normative framework that will have to answer three challenges: the indeterminateness of the autonomy paradigm, the need to acknowledge the future child as an interested stakeholder, and the prospect of broad-scope genomic prenatal screening with a double purpose: autonomy and prevention. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Office-based ultrasound screening for abdominal aortic aneurysm.

Science.gov (United States)

Blois, Beau

2012-03-01

To assess the efficacy of an office-based, family physician–administered ultrasound examination to screen for abdominal aortic aneurysm (AAA). A prospective observational study. Consecutive patients were approached by nonphysician staff. Rural family physician offices in Grand Forks and Revelstoke, BC. The Canadian Society for Vascular Surgery screening recommendations for AAA were used to help select patients who were at risk of AAA. All men 65 years of age or older were included. Women 65 years of age or older were included if they were current smokers or had diabetes, hypertension, a history of coronary artery disease, or a family history of AAA. A focused “quick screen”, which measured the maximal diameter of the abdominal aorta using point-of-care ultrasound technology, was performed in the office by a resident physician trained in emergency ultrasonography. Each patient was then booked for a criterion standard scan (i.e., a conventional abdominal ultrasound scan performed by a technician and interpreted by a radiologist). The maximal abdominal aortic diameter measured by ultrasound in the office was compared with that measured by the criterion standard method. The time to screen each patient was recorded. Forty-five patients were included in data analysis; 62% of participants were men. The mean age was 73 years. The mean pairwise difference between the office-based ultrasound scan and the criterion standard scan was not statistically significant. The mean absolute difference between the 2 scans was 0.20 cm (95% CI 0.15 to 0.25 cm). Correlation between the scans was 0.81. The office-based ultrasound scan had both a sensitivity and a specificity of 100%. The mean time to screen each patient was 212 seconds (95% CI 194 to 230 seconds). Abdominal aortic aneurysm screening can be safely performed in the office by family physicians who are trained to use point-of- care ultrasound technology. The screening test can be completed within the time constraints of a

New antibody and immunoassay pretreatment strategy to screen polychlorinated biphenyls in Korean transformer oil.

Science.gov (United States)

Terakado, Shingo; Ohmura, Naoya; Park, Seok-Un; Lee, Seung-Min; Glass, Thomas R

2013-01-01

Development and modifications are described that expand the application of an immunoassay from the detection of Kanechlors (Japanese technical PCBs mixtures) to the detection of Aroclors (U. S. technical PCB mixtures, used in Korea) in contaminated Korean transformer oil. The first necessary modification was the development of a new antibody with a reactivity profile favorable for Aroclors. The second modification was the addition of a second column to the solid-phase extraction method to reduce assay interference caused by the Korean oil matrix. The matrix interference is suspected to be caused by the presence of synthetic oils (or similar materials) present as contaminants. The modified assay was validated by comparison to high-resolution gas chromatography/high-resolution mass spectrometry analysis, and was shown to be tolerant of up to 10% of several common synthetic insulating oils. Finally the screening performance of the modified assay was evaluated using 500 used transformer oil samples of Korean origin, and was shown to have good performance in terms of false positive and false negative rates. This report provides evidence for the first establishment of immunoassay screening for Aroclor based PCB contamination in Korean transformer oil.

High-throughput screening for bioactive components from traditional Chinese medicine.

Science.gov (United States)

Zhu, Yanhui; Zhang, Zhiyun; Zhang, Meng; Mais, Dale E; Wang, Ming-Wei

2010-12-01

Throughout the centuries, traditional Chinese medicine has been a rich resource in the development of new drugs. Modern drug discovery, which relies increasingly on automated high throughput screening and quick hit-to-lead development, however, is confronted with the challenges of the chemical complexity associated with natural products. New technologies for biological screening as well as library building are in great demand in order to meet the requirements. Here we review the developments in these techniques under the perspective of their applicability in natural product drug discovery. Methods in library building, component characterizing, biological evaluation, and other screening methods including NMR and X-ray diffraction are discussed.

Niobium technological alternatives

International Nuclear Information System (INIS)

Pinatti, D.G.; Dainesi, C.R.

1981-01-01

The process-product matrix of Niobium is presented, through which the technological alternatives for Niobium are identified. It is shown that the three axes of Niobium application, steels, superalloys and metallic Niobium have a tendency to be economical by equivalent. The critical points where technological development of Niobium is needed are analyzed and results are presented on the following products: Nb 2 O 5 by volatilization, metalic Niobium, Niobium powder, bars and sheets, NbTi alloy, corrosion resistent Niobium alloys and superconductor cable and wires. (Author) [pt

Education for screen use as holistic praxis

Directory of Open Access Journals (Sweden)

Lic. José Antonio Gabelas Barroso

2007-09-01

Full Text Available New generations maintain a very close daily relationship with screens (television, Internet, video consoles and mobile telephones. A lot of their leisure time centres on these means of communication with a double purpose: either for playing or communicating with others. These are the two dimensions (recreational and social that dominate the choice of these types of communication in order to entertain oneself and/or establish relationships with their groups of friends. The trend in the consumption of screens has distanced television from its previous monopoly and has meant that it has to share young people’s leisure time with other advanced technological supports. The health of children and adolescents involves educating them towards a healthy and responsible consumption of all screens, in a balanced way as regards dosis and planning, and with criteria as regards the content that could endanger them and the level of their cognitive development.

Effects of Aging and Domain Knowledge on Usability in Small Screen Devices for Diabetes Patients

Science.gov (United States)

Calero Valdez, André; Ziefle, Martina; Horstmann, Andreas; Herding, Daniel; Schroeder, Ulrik

Technology acceptance has become a key concept for the successful rollout of technical devices. Though the concept is intensively studied for nearly 20 years now, still, many open questions remain. This especially applies to technology acceptance of older users, which are known to be very sensitive to suboptimal interfaces and show considerable reservations towards the usage of new technology. Mobile small screen technology increasingly penetrates health care and medical applications. This study investigates impacts of aging, technology expertise and domain knowledge on user interaction using the example of diabetes. For this purpose user effectiveness and efficiency have been measured on a simulated small screen device and related to user characteristics, showing that age and technology expertise have a big impact on usability of the device. Furthermore, impacts of user characteristics and success during the trial on acceptance of the device were surveyed and analyzed.

Saltstone Matrix Characterization And Stadium Simulation Results

International Nuclear Information System (INIS)

Langton, C.

2009-01-01

SIMCO Technologies, Inc. was contracted to evaluate the durability of the saltstone matrix material and to measure saltstone transport properties. This information will be used to: (1) Parameterize the STADIUM(reg s ign) service life code, (2) Predict the leach rate (degradation rate) for the saltstone matrix over 10,000 years using the STADIUM(reg s ign) concrete service life code, and (3) Validate the modeled results by conducting leaching (water immersion) tests. Saltstone durability for this evaluation is limited to changes in the matrix itself and does not include changes in the chemical speciation of the contaminants in the saltstone. This report summarized results obtained to date which include: characterization data for saltstone cured up to 365 days and characterization of saltstone cured for 137 days and immersed in water for 31 days. Chemicals for preparing simulated non-radioactive salt solution were obtained from chemical suppliers. The saltstone slurry was mixed according to directions provided by SRNL. However SIMCO Technologies Inc. personnel made a mistake in the premix proportions. The formulation SIMCO personnel used to prepare saltstone premix was not the reference mix proportions: 45 wt% slag, 45 wt% fly ash, and 10 wt% cement. SIMCO Technologies Inc. personnel used the following proportions: 21 wt% slag, 65 wt% fly ash, and 14 wt% cement. The mistake was acknowledged and new mixes have been prepared and are curing. The results presented in this report are assumed to be conservative since the excessive fly ash was used in the SIMCO saltstone. The SIMCO mixes are low in slag which is very reactive in the caustic salt solution. The impact is that the results presented in this report are expected to be conservative since the samples prepared were deficient in slag and contained excess fly ash. The hydraulic reactivity of slag is about four times that of fly ash so the amount of hydrated binder formed per unit volume in the SIMCO saltstone samples

A comparison of digital mammography detectors and emerging technology

International Nuclear Information System (INIS)

Diffey, J.L.

2015-01-01

The overall diagnostic accuracy of digital mammography in the context of screening has been shown to be similar or slightly better than screen-film mammography. However, digital mammography encompasses both Computed Radiography (CR) and integrated Digital Radiography (DR) and there is increasing evidence to suggest that differences in detector technology are associated with variations in cancer detection rate, dose and image quality. These differences are examined in detail. Although digital mammography offers many advantages compared to screen-film, there are still some limitations with its use as a screening tool and reduced cancer detection in dense breasts remains an issue. Digital mammography detectors have paved the way for emerging technologies which may offer improvements. Taking the definition of mammography to only include X-ray imaging of the breast, this article focuses on tomosynthesis, contrast-enhanced digital mammography, stereoscopic mammography and dedicated breast computed tomography. Advanced software applications such as Computed Aided Detection (CAD) and quantitative breast density assessment are also presented. The benefits and limitations of each technique are discussed. - Highlights: • Digital detector technology affects cancer detection rate, dose and image quality. • Digital detectors have facilitated new technologies such as tomosynthesis. • 3-D techniques reduce superimposition and increase cancer detection in dense breasts. • Contrast-enhanced mammography demonstrates improved sensitivity and specificity.

Application of new technologies for characterization of Hanford Site high-level waste

International Nuclear Information System (INIS)

Winters, W.I.

1998-01-01

To support remediation of Hanford Site high-level radioactive waste tanks, new chemical and physical measurement technologies must be developed and deployed. This is a major task of the Chemistry Analysis Technology Support (CATS) group of the Hanford Corporation. New measurement methods are required for efficient and economical resolution of tank waste safety, waste retrieval, and disposal issues. These development and deployment activities are performed in cooperation with Waste Management Federal Services of Hanford, Inc. This paper provides an overview of current analytical technologies in progress. The high-level waste at the Hanford Site is chemically complex because of the numerous processes used in past nuclear fuel reprocessing there, and a variety of technologies is required for effective characterization. Programmatic and laboratory operational needs drive the selection of new technologies for characterizing Hanford Site high-level waste, and these technologies are developed for deployment in laboratories, hot cells or in the field. New physical methods, such as the propagating reactive systems screening tool (PRSST) to measure the potential for self-propagating reactions in stored wastes, are being implemented. Technology for sampling and measuring gases trapped within the waste matrix is being used to evaluate flammability hazards associated with gas releases from stored wastes. Application of new inductively coupled plasma and laser ablation mass spectrometry systems at the Hanford Site's 222-S Laboratory will be described. A Raman spectroscopy probe mounted in a cone penetrometer to measure oxyanions in wastes or soils will be described. The Hanford Site has used large volumes of organic complexants and acids in processing waste, and capillary zone electrophoresis (CZE) methods have been developed for determining several of the major organic components in complex waste tank matrices. The principles involved, system installation, and results from

Fabrication technology of spherical fuel element for HTR-10

International Nuclear Information System (INIS)

He Jun; Zou Yanwen; Liang Tongxiang; Qiu Xueliang

2002-01-01

R and D on the fabrication technology of the spherical fuel elements for the 10 MW HTR Test Module (HTR-10) began from 1986. Cold quasi-isostatic molding with a silicon rubber die is used for manufacturing the spherical fuel elements.The fabrication technology and the graphite matrix materials were investigated and optimized. Twenty five batches of fuel elements, about 11000 of the fuel elements, have been produced. The cold properties of the graphite matrix materials satisfied the design specifications. The mean free uranium fraction of 25 batches was 5 x 10 -5

Comparison of stimulable phosphor technology and conventional screen-film technology in pediatric scoliosis

International Nuclear Information System (INIS)

Stringer, D.A.; Cairns, R.A.; Poskitt, K.J.; Bray, H.; Milner, R.; Kennedy, B.

1994-01-01

One hundred consecutive patients being investigated for scoliosis were studied using a double cassette containing a conventional film screen and a stimulable phosphor plate. The images were separated, randomised and scored thrice by three radiologists for anatomic structure visualisation. The exposure to the plate and film and repeat rate were measured. Scoliosis angles were comparable on both sets of images, however, visualisation of vertebrae, vertebral end plates, pedicles, spinous processes and other structures were significantly improved (p < 0.0001). Intra- and inter-observer reliability was high with good intraclass correlation. There was a 40% potential exposure reduction, and retakes were decreased from 3 to 0%. We conclude that stimulable phosphor images give better anatomic structure visualisation with potential radiation exposure reduction and lower repeat rate. (orig.)

Evaluating Instructor Technology Integration in Community and Technical Colleges: A Performance Evaluation Matrix

Science.gov (United States)

Del Favero, Marietta; Hinson, Janice M.

2007-01-01

The press for implementing technology based instructional delivery systems in community and technical colleges is well documented. Yet faculty face numerous challenges in integrating technology into instruction (AL-Bataineh & Brooks, 2003; Groves & Zemel, 2000; Khoury, 1997). Stimulating faculty ownership in technology, diffusion of technology use…

Examining pre-service teacher views on the implementation of screen-based writing instruction

Directory of Open Access Journals (Sweden)

Mehmet Tok

2015-03-01

Full Text Available Today, as new technological developments continue to emerge, education, like many other fields, is going through major changes. Technological developments are causing changes to many common concepts. In particular, studies that benefit from technology in the field of education are becoming increasingly widespread, opening the door for the emergence of new teaching methods by abandoning traditional ones. New technologies, and computers in particular, can benefit the teaching of writing, the most complex of the four basic language skills (reading, writing, speaking, and listening. This study aims to explore pre-service teachers' views on screen-based writing practices via a course they attended. A qualitative case study method (holistic single-case design was employed to explore pre-service teachers’ views. The study participants were selected using a purposeful sampling method among 4th year students majoring in Turkish Language Teaching at a major state university. The study group consisted of sixty-two pre-service teachers who were enrolled in the “Written Expression” I and II courses in the 2013-2014 education year. The study was conducted both in Fall and Spring semesters. All writing activities were conducted in a digital environment. The study results revealed that a majority (77% of the pre-service teachers favored continuation of the screen-based writing instruction. The study supported that digital literacy is important and the advantages of screen-based writing instruction outweighed its disadvantages. Screen-based writing activities should be integrated into the courses and instruction materials of pre-service Turkish teachers’ education programs.

Multi-threaded Sparse Matrix-Matrix Multiplication for Many-Core and GPU Architectures.

Energy Technology Data Exchange (ETDEWEB)

Deveci, Mehmet [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rajamanickam, Sivasankaran [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trott, Christian Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-12-01

Sparse Matrix-Matrix multiplication is a key kernel that has applications in several domains such as scienti c computing and graph analysis. Several algorithms have been studied in the past for this foundational kernel. In this paper, we develop parallel algorithms for sparse matrix-matrix multiplication with a focus on performance portability across different high performance computing architectures. The performance of these algorithms depend on the data structures used in them. We compare different types of accumulators in these algorithms and demonstrate the performance difference between these data structures. Furthermore, we develop a meta-algorithm, kkSpGEMM, to choose the right algorithm and data structure based on the characteristics of the problem. We show performance comparisons on three architectures and demonstrate the need for the community to develop two phase sparse matrix-matrix multiplication implementations for efficient reuse of the data structures involved.

The nuclear reaction matrix

International Nuclear Information System (INIS)

Krenciglowa, E.M.; Kung, C.L.; Kuo, T.T.S.; Osnes, E.; and Department of Physics, State University of New York at Stony Brook, Stony Brook, New York 11794)

1976-01-01

Different definitions of the reaction matrix G appropriate to the calculation of nuclear structure are reviewed and discussed. Qualitative physical arguments are presented in support of a two-step calculation of the G-matrix for finite nuclei. In the first step the high-energy excitations are included using orthogonalized plane-wave intermediate states, and in the second step the low-energy excitations are added in, using harmonic oscillator intermediate states. Accurate calculations of G-matrix elements for nuclear structure calculations in the Aapprox. =18 region are performed following this procedure and treating the Pauli exclusion operator Q 2 /sub p/ by the method of Tsai and Kuo. The treatment of Q 2 /sub p/, the effect of the intermediate-state spectrum and the energy dependence of the reaction matrix are investigated in detail. The present matrix elements are compared with various matrix elements given in the literature. In particular, close agreement is obtained with the matrix elements calculated by Kuo and Brown using approximate methods

Optimal Substrate Preheating Model for Thermal Spray Deposition of Thermosets onto Polymer Matrix Composites

Science.gov (United States)

Ivosevic, M.; Knight, R.; Kalidindi, S. R.; Palmese, G. R.; Tsurikov, A.; Sutter, J. K.

2003-01-01

High velocity oxy-fuel (HVOF) sprayed, functionally graded polyimide/WC-Co composite coatings on polymer matrix composites (PMC's) are being investigated for applications in turbine engine technologies. This requires that the polyimide, used as the matrix material, be fully crosslinked during deposition in order to maximize its engineering properties. The rapid heating and cooling nature of the HVOF spray process and the high heat flux through the coating into the substrate typically do not allow sufficient time at temperature for curing of the thermoset. It was hypothesized that external substrate preheating might enhance the deposition behavior and curing reaction during the thermal spraying of polyimide thermosets. A simple analytical process model for the deposition of thermosetting polyimide onto polymer matrix composites by HVOF thermal spray technology has been developed. The model incorporates various heat transfer mechanisms and enables surface temperature profiles of the coating to be simulated, primarily as a function of substrate preheating temperature. Four cases were modeled: (i) no substrate preheating; (ii) substrates electrically preheated from the rear; (iii) substrates preheated by hot air from the front face; and (iv) substrates electrically preheated from the rear and by hot air from the front.

The screening effects of the screened exchange hybrid functional in surface systems: A case study on the CO/Pt(111) problem

Energy Technology Data Exchange (ETDEWEB)

Li, H., E-mail: li-huanglong@mail.tsinghua.edu.cn [Department of Precision Instrument, Tsinghua University, Beijing, 100084 (China); Gillen, R. [Institut für Festkörperphysik. Technische Universität Berlin. Hardenbergstr. 36, 10623 Berlin (Germany); Robertson, J., E-mail: jr214@cam.ac.uk [Engineering Department, University of Cambridge, Cambridge CB2 1PZ (United Kingdom)

2016-06-15

The screened exchange (sX) hybrid functional has been widely used in computational material science. Although it has widely been studied in bulk systems, less is known about its functional behavior in surface systems which are crucial to many technologies such as materials synthesis and nano-electronic devices. Assessing the screening dependent functional behaviors in the surface systems is therefore important for its application in such systems. In this work, we investigate the screening effects of the sX in CO adsorption on Pt(111) surface. The differences between the sX and Heyd-Scuseria-Ernzerhof (HSE06) hybrid functionals, and the effects of screening parameters are studied. The screening has two effects: first, the HOMO-LUMO gap is screening dependent. This affects the site preference most significantly. In this work, atop adsorption of CO/Pt(111) is predicted by the hybrid functionals with screened exchange potential. The sX(1.44) gives the largest HOMO-LUMO gap for the isolated CO molecule. The adsorption energy difference between the atop and fcc site is also the largest by the sX(1.44) which is explained by the reduced metal d states to the CO 2π* state back-donation, with stronger effect for the fcc adsorption than for the atop adsorption; second, the adsorption energy is screening dependent. This can be seen by comparing the sX(2.38) and HSE06 which have different screening strengths. They show similar surface band structures for the CO adsorption but different adsorption energies, which is explained by the stronger CO 5σ state to the metal d states donation or the effectively screened Pauli repulsion. This work underlines the screening strength as a main difference between sX and HSE06, as well as an important hybrid functional parameter for surface calculation.

Technologies for Single-Cell Isolation

Science.gov (United States)

Gross, Andre; Schoendube, Jonas; Zimmermann, Stefan; Steeb, Maximilian; Zengerle, Roland; Koltay, Peter

2015-01-01

The handling of single cells is of great importance in applications such as cell line development or single-cell analysis, e.g., for cancer research or for emerging diagnostic methods. This review provides an overview of technologies that are currently used or in development to isolate single cells for subsequent single-cell analysis. Data from a dedicated online market survey conducted to identify the most relevant technologies, presented here for the first time, shows that FACS (fluorescence activated cell sorting) respectively Flow cytometry (33% usage), laser microdissection (17%), manual cell picking (17%), random seeding/dilution (15%), and microfluidics/lab-on-a-chip devices (12%) are currently the most frequently used technologies. These most prominent technologies are described in detail and key performance factors are discussed. The survey data indicates a further increasing interest in single-cell isolation tools for the coming years. Additionally, a worldwide patent search was performed to screen for emerging technologies that might become relevant in the future. In total 179 patents were found, out of which 25 were evaluated by screening the title and abstract to be relevant to the field. PMID:26213926

Technologies for Single-Cell Isolation

Directory of Open Access Journals (Sweden)

Andre Gross

2015-07-01

Full Text Available The handling of single cells is of great importance in applications such as cell line development or single-cell analysis, e.g., for cancer research or for emerging diagnostic methods. This review provides an overview of technologies that are currently used or in development to isolate single cells for subsequent single-cell analysis. Data from a dedicated online market survey conducted to identify the most relevant technologies, presented here for the first time, shows that FACS (fluorescence activated cell sorting respectively Flow cytometry (33% usage, laser microdissection (17%, manual cell picking (17%, random seeding/dilution (15%, and microfluidics/lab-on-a-chip devices (12% are currently the most frequently used technologies. These most prominent technologies are described in detail and key performance factors are discussed. The survey data indicates a further increasing interest in single-cell isolation tools for the coming years. Additionally, a worldwide patent search was performed to screen for emerging technologies that might become relevant in the future. In total 179 patents were found, out of which 25 were evaluated by screening the title and abstract to be relevant to the field.

Technologies for Single-Cell Isolation.

Science.gov (United States)

Gross, Andre; Schoendube, Jonas; Zimmermann, Stefan; Steeb, Maximilian; Zengerle, Roland; Koltay, Peter

2015-07-24

The handling of single cells is of great importance in applications such as cell line development or single-cell analysis, e.g., for cancer research or for emerging diagnostic methods. This review provides an overview of technologies that are currently used or in development to isolate single cells for subsequent single-cell analysis. Data from a dedicated online market survey conducted to identify the most relevant technologies, presented here for the first time, shows that FACS (fluorescence activated cell sorting) respectively Flow cytometry (33% usage), laser microdissection (17%), manual cell picking (17%), random seeding/dilution (15%), and microfluidics/lab-on-a-chip devices (12%) are currently the most frequently used technologies. These most prominent technologies are described in detail and key performance factors are discussed. The survey data indicates a further increasing interest in single-cell isolation tools for the coming years. Additionally, a worldwide patent search was performed to screen for emerging technologies that might become relevant in the future. In total 179 patents were found, out of which 25 were evaluated by screening the title and abstract to be relevant to the field.

A focus group study of consumer attitudes toward genetic testing and newborn screening for deafness.

Science.gov (United States)

Burton, Sarah K; Withrow, Kara; Arnos, Kathleen S; Kalfoglou, Andrea L; Pandya, Arti

2006-12-01

Progress in identifying genes for deafness together with implementation of universal audiologic screening of newborns has provided the opportunity for more widespread use of molecular tests to detect genetic forms of hearing loss. Efforts to assess consumer attitudes toward these advances have lagged behind. Consumer focus groups were held to explore attitudes toward genetic advances and technologies for hearing loss, views about newborn hearing screening, and reactions to the idea of adding molecular screening for hearing loss at birth. Focus group discussions were recorded, transcribed and analyzed. Five focus groups with 44 participants including hearing parents of deaf children, deaf parents and young deaf adults were held. Focus group participants supported the use of genetic tests to identify the etiology of hearing loss but were concerned that genetic information might influence reproductive decisions. Molecular newborn screening was advocated by some; however, others expressed concern about its effectiveness. Documenting the attitudes of parents and other consumers toward genetic technologies establishes the framework for discussions on the appropriateness of molecular newborn screening for hearing loss and informs specialists about potential areas of public education necessary prior to the implementation of such screening.

A stretchable and screen-printable conductive ink for stretchable electronics

Science.gov (United States)

Mohammed, Anwar; Pecht, Michael

2016-10-01

Stretchable electronics can offer an added degree of design freedom and generate products with unprecedented capabilities. Stretchable conductive ink serving as interconnect, is a key enabler for stretchable electronics. This paper focuses on the development of a stretchable and screen printable conductive ink which could be stretched more than 500 cycles at 20% strain while maintaining electrical and mechanical integrity. The screen printable and stretchable conductive ink developed in this paper marks an important milestone for this nascent technology.

Evidence of rock matrix back-diffusion and abiotic dechlorination using a field testing approach

Science.gov (United States)

Schaefer, Charles E.; Lippincott, David R.; Klammler, Harald; Hatfield, Kirk

2018-02-01

An in situ field demonstration was performed in fractured rock impacted with trichloroethene (TCE) and cis-1,2-dichloroethene (DCE) to assess the impacts of contaminant rebound after removing dissolved contaminants within hydraulically conductive fractures. Using a bedrock well pair spaced 2.4 m apart, TCE and DCE were first flushed with water to create a decrease in dissolved contaminant concentrations. While hydraulically isolating the well pair from upgradient contaminant impacts, contaminant rebound then was observed between the well pair over 151 days. The magnitude, but not trend, of TCE rebound was reasonably described by a matrix back-diffusion screening model that employed an effective diffusion coefficient and first-order abiotic TCE dechlorination rate constant that was based on bench-scale testing. Furthermore, a shift in the TCE:DCE ratio and carbon isotopic enrichment was observed during the rebound, suggesting that both biotic and abiotic dechlorination were occurring within the rock matrix. The isotopic data and back-diffusion model together served as a convincing argument that matrix back-diffusion was the mechanism responsible for the observed contaminant rebound. Results of this field demonstration highlight the importance and applicability of rock matrix parameters determined at the bench-scale, and suggest that carbon isotopic enrichment can be used as a line of evidence for abiotic dechlorination within rock matrices.

Global unitary fixing and matrix-valued correlations in matrix models

International Nuclear Information System (INIS)

Adler, Stephen L.; Horwitz, Lawrence P.

2003-01-01

We consider the partition function for a matrix model with a global unitary invariant energy function. We show that the averages over the partition function of global unitary invariant trace polynomials of the matrix variables are the same when calculated with any choice of a global unitary fixing, while averages of such polynomials without a trace define matrix-valued correlation functions, that depend on the choice of unitary fixing. The unitary fixing is formulated within the standard Faddeev-Popov framework, in which the squared Vandermonde determinant emerges as a factor of the complete Faddeev-Popov determinant. We give the ghost representation for the FP determinant, and the corresponding BRST invariance of the unitary-fixed partition function. The formalism is relevant for deriving Ward identities obeyed by matrix-valued correlation functions

Genome-wide RNAi Screening to Identify Host Factors That Modulate Oncolytic Virus Therapy.

Science.gov (United States)

Allan, Kristina J; Mahoney, Douglas J; Baird, Stephen D; Lefebvre, Charles A; Stojdl, David F

2018-04-03

High-throughput genome-wide RNAi (RNA interference) screening technology has been widely used for discovering host factors that impact virus replication. Here we present the application of this technology to uncovering host targets that specifically modulate the replication of Maraba virus, an oncolytic rhabdovirus, and vaccinia virus with the goal of enhancing therapy. While the protocol has been tested for use with oncolytic Maraba virus and oncolytic vaccinia virus, this approach is applicable to other oncolytic viruses and can also be utilized for identifying host targets that modulate virus replication in mammalian cells in general. This protocol describes the development and validation of an assay for high-throughput RNAi screening in mammalian cells, the key considerations and preparation steps important for conducting a primary high-throughput RNAi screen, and a step-by-step guide for conducting a primary high-throughput RNAi screen; in addition, it broadly outlines the methods for conducting secondary screen validation and tertiary validation studies. The benefit of high-throughput RNAi screening is that it allows one to catalogue, in an extensive and unbiased fashion, host factors that modulate any aspect of virus replication for which one can develop an in vitro assay such as infectivity, burst size, and cytotoxicity. It has the power to uncover biotherapeutic targets unforeseen based on current knowledge.

Parental Reports on Touch Screen Use in Early Childhood.

Directory of Open Access Journals (Sweden)

Alejandrina Cristia

Full Text Available Touch screens are increasingly prevalent, and anecdotal evidence suggests that young children are very drawn towards them. Yet there is little data regarding how young children use them. A brief online questionnaire queried over 450 French parents of infants between the ages of 5 and 40 months on their young child's use of touch-screen technology. Parents estimated frequency of use, and further completed several checklists. Results suggest that, among respondent families, the use of touch screens is widespread in early childhood, meaning that most children have some exposure to touch screens. Among child users, certain activities are more frequently reported to be liked than others, findings that we discuss in light of current concern for children's employment of time and the cognitive effects of passive media exposure. Additionally, these parental reports point to clear developmental trends for certain types of interactive gestures. These results contribute to the investigation of touch screen use on early development and suggest a number of considerations that should help improve the design of applications geared towards toddlers, particularly for scientific purposes.

Parental Reports on Touch Screen Use in Early Childhood.

Science.gov (United States)

Cristia, Alejandrina; Seidl, Amanda

2015-01-01

Touch screens are increasingly prevalent, and anecdotal evidence suggests that young children are very drawn towards them. Yet there is little data regarding how young children use them. A brief online questionnaire queried over 450 French parents of infants between the ages of 5 and 40 months on their young child's use of touch-screen technology. Parents estimated frequency of use, and further completed several checklists. Results suggest that, among respondent families, the use of touch screens is widespread in early childhood, meaning that most children have some exposure to touch screens. Among child users, certain activities are more frequently reported to be liked than others, findings that we discuss in light of current concern for children's employment of time and the cognitive effects of passive media exposure. Additionally, these parental reports point to clear developmental trends for certain types of interactive gestures. These results contribute to the investigation of touch screen use on early development and suggest a number of considerations that should help improve the design of applications geared towards toddlers, particularly for scientific purposes.

Interactive displays natural human-interface technologies

CERN Document Server

Bhowmik, Achintya K

2014-01-01

One of the first books to provide an in-depth discussion of the technologies, applications and trends in the rapidly emerging field of interactive displays (touch, gesture & voice) The book will cover the technologies, applications and trends in the field of interactive displays, namely interfaces based on touch, gesture and voice and those using a combination of these technologies. The book will be split into 4 main parts with each being dedicated to a specific user interface. Part 1 ''Touch Interfaces'' will provide a review of the currently deployed touch-screen technologies and applications. It will also cover the recent developments towards achieving thinner, lightweight and cost-reduced touch screen panels in the future via integration of touch functionalities. Part 2 ''Gesture Interfaces'' will examine techniques and applications in stereoscopic 3D computer vision, structured-light 3D computer vision and time-of-flight 3D computer vision in gesture interfaces. Part 3 ''Voice Interfaces'' will revie...

Digitisation of analogue screening mammograms. Norwegian Breast Cancer Screening Program Troms and Finnmark

International Nuclear Information System (INIS)

Pedersen, Kristin; Johansen, Stian; Roenning, Frank; Stormo, Sonja; Bjurstam, Nils

2004-08-01

In the coming years a transition from analogue to digital imaging technology will take place in the Norwegian Breast Cancer Screening Program (NBCSP). This will make softcopy reading of images possible. However, one will also wish to compare new (digital) images with prior images on on film. This can be solved in different ways. This report contains a brief description of different alternatives. The solution chosen in Troms and Finnmark, digitisation of prior images, is then described in detail. Both technical and economical aspects are covered. (Author)