WorldWideScience

Sample records for techniques yield full-field

  1. Full-field wafer warpage measurement technique

    Science.gov (United States)

    Hsieh, H. L.; Lee, J. Y.; Huang, Y. G.; Liang, A. J.; Sun, B. Y.

    2017-06-01

    An innovative moiré technique for full-field wafer warpage measurement is proposed in this study. The wafer warpage measurement technique is developed based on moiré method, Talbot effect, scanning profiling method, stroboscopic, instantaneous phase-shift method, as well as four-step phase shift method, high resolution, high stability and full-field measurement capabilities can be easily achieved. According to the proposed full-field optical configuration, a laser beam is expanded into a collimated beam with a 2-inch diameter and projected onto the wafer surface. The beam is reflected by the wafer surface and forms a moiré fringe image after passing two circular gratings, which is then focused and captured on a CCD camera for computation. The corresponding moiré fringes reflected from the wafer surface are obtained by overlapping the images of the measuring grating and the reference grating. The moiré fringes will shift when wafer warpage occurs. The phase of the moiré fringes will change proportionally to the degree of warpage in the wafer, which can be measured by detecting variations in the phase shift of the moiré fringes in each detection points on the surface of the entire wafer. The phase shift variations of each detection points can be calculated via the instantaneous phase-shift method and the four-step phase-shift method. By adding up the phase shift variations of each detection points along the radii of the circular gratings, the warpage value and surface topography of the wafer can be obtained. Experiments show that the proposed method is capable of obtaining test results similar to that of a commercial sensor, as well as performing accurate measurements under high speed rotation of 1500rpm. As compared to current warpage measurement methods such as the beam optical method, confocal microscopy, laser interferometry, shadow moiré method, and structured light method, this proposed technique has the advantage of full-field measurement, high

  2. Calibration and validation of full-field techniques

    Directory of Open Access Journals (Sweden)

    Thalmann R.

    2010-06-01

    Full Text Available We review basic metrological terms related to the use of measurement equipment for verification of numerical model calculations. We address three challenges that are faced when performing measurements in experimental mechanics with optical techniques: the calibration of a measuring instrument that (i measures strain values, (ii provides full-field data, and (iii is dynamic.

  3. Full-field laser vibration measurement in NDT techniques

    Science.gov (United States)

    Yue, Kaiduan; Li, Zhongke; Yi, Yaxing; Zhang, Fei

    2008-12-01

    Research of Non Destructive Testing (NDT) methodology has developed rapidly in recent years[1][2]. But it is rarely used for small objects such as Micro-electronic Mechanics System. Due to the small size of the MEMS, the traditional method of contact measurement seriously affects the parameter of the object measured. So a high accuracy non-contact measurement is required for optimization of MEMS designs and improvement of its reliability[3][4]. With recent advances in photonics, electronics, and computer technology, a Non Destructive Testing (NDT) laser time average interferometry is proposed in the paper. Laser interferometry has the advantages of non-contact, high accuracy, full-field and fast speed, so it can be used to detect cracks in MEMS. A time average measurement method of digital speckle pattern interferometry is proposed to measure the vibration mode of the MEMS in the paper. According to the sudden change of amplitude of vibration mode, a crack can be measured. With the speckle average technology, high accuracy phase-shift, continuous phase scanning technology, combined with optical amplification technology, the resolution of the amplitude reaches 1nm, and the resolution of the crack reaches 5μm. The measurement system being full-field, the measuring speed of the measurement system can reach 512*512 points per one minute.

  4. Full-field speckle correlation technique as applied to blood flow monitoring

    Science.gov (United States)

    Vilensky, M. A.; Agafonov, D. N.; Timoshina, P. A.; Shipovskaya, O. V.; Zimnyakov, D. A.; Tuchin, V. V.; Novikov, P. A.

    2011-03-01

    The results of experimental study of monitoring the microcirculation in tissue superficial layers of the internal organs at gastro-duodenal hemorrhage with the use of laser speckles contrast analysis technique are presented. The microcirculation monitoring was provided in the course of the laparotomy of rat abdominal cavity in the real time. Microscopic hemodynamics was analyzed for small intestine and stomach under different conditions (normal state, provoked ischemia, administration of vasodilative agents such as papaverine, lidocaine). The prospects and problems of internal monitoring of micro-vascular flow in clinical conditions are discussed.

  5. X-ray and visible light transmission as two-dimensional, full-field moisture-sensing techniques: A preliminary comparison

    Energy Technology Data Exchange (ETDEWEB)

    Tidwell, V.C.; Glass, R.J.

    1992-01-21

    Two independent high-resolution moisture-sensing techniques, x-ray absorption and light transmission, have been developed for use in two-dimensional, thin-slab experimental systems. The techniques yield full-field measurement capabilities with exceptional resolution of moisture content in time and space. These techniques represent powerful tools for the experimentalist to investigate processes governing unsaturated flow and transport through fractured and nonfractured porous media. Evaluation of these techniques has been accomplished by direct comparison of data obtained by means of the x-ray and light techniques as well as comparison with data collected by gravimetric and gamma-ray densitometry techniques. Results show excellent agreement between data collected by the four moisture-content measurement techniques. This program was established to support the Yucca Mountain Site Characterization Project.

  6. Redox and speciation mapping of rock thin sections using high spatial resolution full-field imaging technique

    Science.gov (United States)

    de Andrade, V.; Susini, J.; Salomé, M.; Beraldin, O.; Heymes, T.; Lewin, E.

    2009-04-01

    Because of their complex genesis, natural rocks are the most often heterogeneous systems, with various scale-level heterogeneities for both chemistry and structure. In the last decade, the dramatic improvements of hyperspectral imaging techniques provided new tools for accurate material characterisation. Most of these micro- and nano- analytical techniques rely on scanning instruments, which offer high spatial resolution but suffer from long acquisition times imposing practical limits on the field of view. Conversely, full-field imaging techniques rely on a fast parallel acquisition but have limited resolution. Although soft X-ray full-field microscopes based on Fresnel zone plates are commonly used for high resolution imaging, its combination with spectroscopy is challenging and 2D chemical mapping still difficult. For harder X-rays, lensless X-ray microscope based on simple propagation geometry is easier and can be readily used for 2D spectro-microscopy. A full-field experimental setup was optimized at the ESRF-ID21 beamline to image iron redox and speciation distributions in rocks thin sections. The setup comprises a Si111 or Si220 (E = 0.4 eV) monochromator, a special sample stage and a sensitive camera associated with a brand new GGG:Eu light conversion scintillator and high magnification visible light optics. The pixel size ranges from 1.6 to 0.16 m according to the optic used. This instrument was used to analyse phyllosilicates and oxides of metamorphic sediments coming from the Aspromonte nappes-pile in Calabria. Iron chemical state distributions were derived - from images of 1000 Ã- 2000 Ã- 30 m3 rock thin sections - by subtraction of absorption images above and below the Fe K-edge. Using an automatic stitching reconstruction, a wide field image (4Ã-3 mm2 with a 1 m2 resolution for a total of about 12 millions pixels) of Fetotal elemental distribution was produced. Moreover, -XANES analyses (more than 1 million individual -XANES spectra) were performed

  7. A real-time, full-field, and low-cost velocity sensing approach for linear motion using fringe projection techniques

    Science.gov (United States)

    Su, Wei-Hung; Co, Wei-Ting

    2016-06-01

    A velocity sensing approach using the fringe projection technique is presented. The moving object is projected with a sinusoidal fringe pattern. A CCD camera located at a different view angle observes the projected fringes on the dynamic object. The long exposure time of the CCD camera makes the fringes blurred by linear motion. The blurred fringes provide additional information to describe the depth displacement, and therefore the velocity vector can be identified. There is no need to take multiple-shot measurements to address the change in 3D positions at a sequence of time. Only one-shot measurement is required. Consequently, there is no need to perform image registration. The full-field approach also makes it possible to simultaneously inspect several objects.

  8. Extracting full-field dynamic strain on a wind turbine rotor subjected to arbitrary excitations using 3D point tracking and a modal expansion technique

    Science.gov (United States)

    Baqersad, Javad; Niezrecki, Christopher; Avitabile, Peter

    2015-09-01

    Health monitoring of rotating structures such as wind turbines and helicopter rotors is generally performed using conventional sensors that provide a limited set of data at discrete locations near or on the hub. These sensors usually provide no data on the blades or inside them where failures might occur. Within this paper, an approach was used to extract the full-field dynamic strain on a wind turbine assembly subject to arbitrary loading conditions. A three-bladed wind turbine having 2.3-m long blades was placed in a semi-built-in boundary condition using a hub, a machining chuck, and a steel block. For three different test cases, the turbine was excited using (1) pluck testing, (2) random impacts on blades with three impact hammers, and (3) random excitation by a mechanical shaker. The response of the structure to the excitations was measured using three-dimensional point tracking. A pair of high-speed cameras was used to measure displacement of optical targets on the structure when the blades were vibrating. The measured displacements at discrete locations were expanded and applied to the finite element model of the structure to extract the full-field dynamic strain. The results of the paper show an excellent correlation between the strain predicted using the proposed approach and the strain measured with strain-gages for each of the three loading conditions. The approach used in this paper to predict the strain showed higher accuracy than the digital image correlation technique. The new expansion approach is able to extract dynamic strain all over the entire structure, even inside the structure beyond the line of sight of the measurement system. Because the method is based on a non-contacting measurement approach, it can be readily applied to a variety of structures having different boundary and operating conditions, including rotating blades.

  9. Multi-scale full-field measurements and near-wall modeling of turbulent subcooled boiling flow using innovative experimental techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Yassin A., E-mail: y-hassan@tamu.edu

    2016-04-01

    Highlights: • Near wall full-field velocity components under subcooled boiling were measured. • Simultaneous shadowgraphy, infrared thermometry wall temperature and particle-tracking velocimetry techniques were combined. • Near wall velocity modifications under subcooling boiling were observed. - Abstract: Multi-phase flows are one of the challenges on which the CFD simulation community has been working extensively with a relatively low success. The phenomena associated behind the momentum and heat transfer mechanisms associated to multi-phase flows are highly complex requiring resolving simultaneously for multiple scales on time and space. Part of the reasons behind the low predictive capability of CFD when studying multi-phase flows, is the scarcity of CFD-grade experimental data for validation. The complexity of the phenomena and its sensitivity to small sources of perturbations makes its measurements a difficult task. Non-intrusive and innovative measuring techniques are required to accurately measure multi-phase flow parameters while at the same time satisfying the high resolution required to validate CFD simulations. In this context, this work explores the feasible implementation of innovative measuring techniques that can provide whole-field and multi-scale measurements of two-phase flow turbulence, heat transfer, and boiling parameters. To this end, three visualization techniques are simultaneously implemented to study subcooled boiling flow through a vertical rectangular channel with a single heated wall. These techniques are listed next and are used as follow: (1) High-speed infrared thermometry (IR-T) is used to study the impact of the boiling level on the heat transfer coefficients at the heated wall, (2) Particle Tracking Velocimetry (PTV) is used to analyze the influence that boiling parameters have on the liquid phase turbulence statistics, (3) High-speed shadowgraphy with LED illumination is used to obtain the gas phase dynamics. To account

  10. A non-contacting approach for full field dynamic strain monitoring of rotating structures using the photogrammetry, finite element, and modal expansion techniques

    Science.gov (United States)

    Baqersad, Javad

    Health monitoring of rotating structures such as wind turbines and helicopter rotors is generally performed using conventional sensors that provide a limited set of data at discrete locations near or on the hub. These sensors usually provide no data on the blades or interior locations where failures may occur. Within this work, an unique expansion algorithm was extended and combined with finite element (FE) modeling and an optical measurement technique to identify the dynamic strain in rotating structures. The merit of the approach is shown by using the approach to predict the dynamic strain on a small non-rotating and rotating wind turbine. A three-bladed wind turbine having 2.3-meter long blades was placed in a semi-built-in boundary condition using a hub, a machining chuck, and a steel block. A finite element model of the three wind turbine blades assembled to the hub was created and used to extract resonant frequencies and mode shapes. The FE model was validated and updated using experimental modal tests. For the non-rotating optical test, the turbine was excited using a sinusoidal excitation, a pluck test, arbitrary impacts on three blades, and random force excitations with a mechanical shaker. The response of the structure to the excitations was measured using three-dimensional point tracking. A pair of high-speed cameras was used to measure the displacement of optical targets on the structure when the blades were vibrating. The measured displacements at discrete locations were expanded and applied to the finite element model of the structure to extract the full-field dynamic strain. The results of the work show an excellent correlation between the strain predicted using the proposed approach and the strain measured with strain-gages for all of the three loading conditions. Similar to the non-rotating case, optical measurements were also preformed on a rotating wind turbine. The point tracking technique measured both rigid body displacement and flexible

  11. Measurement of Full Field Strains in Filament Wound Composite Tubes Under Axial Compressive Loading by the Digital Image Correlation (DIC) Technique

    Science.gov (United States)

    2013-05-01

    McNeill , S. R. Determination of Displacements Using an Improved Digital Image Correlation Method. Computer Vision August 1983. 13 12. Bruck, H. A... McNeill , S. R.; Russell, S. S.; Sutton, M. A. Use of Digital Image Correlation for Determination of Displacements and Strains. Non-Destructive...Evaluation for Aerospace Requirements, 1989. 13. Sutton, M. A.; McNeill , S. R.; Helm, J. D.; Schreier, H. Full-field Non-Contacting Measurement of

  12. Compact muon solenoid magnet reaches full field

    CERN Multimedia

    2006-01-01

    Scientist of the U.S. Department of Energy in Fermilab and collaborators of the US/CMS project announced that the world's largest superconducting solenoid magnet has reached full field in tests at CERN. (1 apge)

  13. Laser Resurfacing: Full Field and Fractional.

    Science.gov (United States)

    Pozner, Jason N; DiBernardo, Barry E

    2016-07-01

    Laser resurfacing is a very popular procedure worldwide. Full field and fractional lasers are used in many aesthetic practices. There have been significant advances in laser resurfacing in the past few years, which make patient treatments more efficacious and with less downtime. Erbium and carbon dioxide and ablative, nonablative, and hybrid fractional lasers are all extremely effective and popular tools that have a place in plastic surgery and dermatology offices.

  14. Crop Yield Forecasted Model Based on Time Series Techniques

    Institute of Scientific and Technical Information of China (English)

    Li Hong-ying; Hou Yan-lin; Zhou Yong-juan; Zhao Hui-ming

    2012-01-01

    Traditional studies on potential yield mainly referred to attainable yield: the maximum yield which could be reached by a crop in a given environment. The new concept of crop yield under average climate conditions was defined in this paper, which was affected by advancement of science and technology. Based on the new concept of crop yield, the time series techniques relying on past yield data was employed to set up a forecasting model. The model was tested by using average grain yields of Liaoning Province in China from 1949 to 2005. The testing combined dynamic n-choosing and micro tendency rectification, and an average forecasting error was 1.24%. In the trend line of yield change, and then a yield turning point might occur, in which case the inflexion model was used to solve the problem of yield turn point.

  15. Imaging of transient surface acoustic waves by full-field photorefractive interferometry

    Science.gov (United States)

    Xiong, Jichuan; Xu, Xiaodong; Glorieux, Christ; Matsuda, Osamu; Cheng, Liping

    2015-05-01

    A stroboscopic full-field imaging technique based on photorefractive interferometry for the visualization of rapidly changing surface displacement fields by using of a standard charge-coupled device (CCD) camera is presented. The photorefractive buildup of the space charge field during and after probe laser pulses is simulated numerically. The resulting anisotropic diffraction upon the refractive index grating and the interference between the polarization-rotated diffracted reference beam and the transmitted signal beam are modeled theoretically. The method is experimentally demonstrated by full-field imaging of the propagation of photoacoustically generated surface acoustic waves with a temporal resolution of nanoseconds. The surface acoustic wave propagation in a 23 mm × 17 mm area on an aluminum plate was visualized with 520 × 696 pixels of the CCD sensor, yielding a spatial resolution of 33 μm. The short pulse duration (8 ns) of the probe laser yields the capability of imaging SAWs with frequencies up to 60 MHz.

  16. Imaging of transient surface acoustic waves by full-field photorefractive interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Xiong, Jichuan [Key Laboratory of Modern Acoustics, Nanjing University, Nanjing 210093 (China); School of Electronic and Optical Engineering, Nanjing University of Science and Technology, 200 Xiaolingwei, Nanjing 210094 (China); Soft Matter and Biophysics, Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, 3001 Heverlee (Belgium); Xu, Xiaodong, E-mail: xdxu@nju.edu.cn, E-mail: christ.glorieux@fys.kuleuven.be [Key Laboratory of Modern Acoustics, Nanjing University, Nanjing 210093 (China); Soft Matter and Biophysics, Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, 3001 Heverlee (Belgium); Glorieux, Christ, E-mail: xdxu@nju.edu.cn, E-mail: christ.glorieux@fys.kuleuven.be [Soft Matter and Biophysics, Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, 3001 Heverlee (Belgium); Matsuda, Osamu [Division of Applied Physics, Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Cheng, Liping [Key Laboratory of Modern Acoustics, Nanjing University, Nanjing 210093 (China)

    2015-05-15

    A stroboscopic full-field imaging technique based on photorefractive interferometry for the visualization of rapidly changing surface displacement fields by using of a standard charge-coupled device (CCD) camera is presented. The photorefractive buildup of the space charge field during and after probe laser pulses is simulated numerically. The resulting anisotropic diffraction upon the refractive index grating and the interference between the polarization-rotated diffracted reference beam and the transmitted signal beam are modeled theoretically. The method is experimentally demonstrated by full-field imaging of the propagation of photoacoustically generated surface acoustic waves with a temporal resolution of nanoseconds. The surface acoustic wave propagation in a 23 mm × 17 mm area on an aluminum plate was visualized with 520 × 696 pixels of the CCD sensor, yielding a spatial resolution of 33 μm. The short pulse duration (8 ns) of the probe laser yields the capability of imaging SAWs with frequencies up to 60 MHz.

  17. Pancreatic cancer study based on full field OCT and dynamic full field OCT (Conference Presentation)

    Science.gov (United States)

    Apelian, Clement; Camus, Marine; Prat, Frederic; Boccara, A. Claude

    2017-02-01

    Pancreatic cancer is one of the most feared cancer types due to high death rates and the difficulty to perform surgery. This cancer outcome could benefit from recent technological developments for diagnosis. We used a combination of standard Full Field OCT and Dynamic Full Field OCT to capture both morphological features and metabolic functions of rodents pancreas in normal and cancerous conditions with and without chemotherapy. Results were compared to histology to evaluate the performances and the specificities of the method. The comparison highlighted the importance of a number of endogenous markers like immune cells, fibrous development, architecture and more.

  18. Prediction of Potato Crop Yield Using Precision Agriculture Techniques.

    Science.gov (United States)

    Al-Gaadi, Khalid A; Hassaballa, Abdalhaleem A; Tola, ElKamil; Kayad, Ahmed G; Madugundu, Rangaswamy; Alblewi, Bander; Assiri, Fahad

    2016-01-01

    Crop growth and yield monitoring over agricultural fields is an essential procedure for food security and agricultural economic return prediction. The advances in remote sensing have enhanced the process of monitoring the development of agricultural crops and estimating their yields. Therefore, remote sensing and GIS techniques were employed, in this study, to predict potato tuber crop yield on three 30 ha center pivot irrigated fields in an agricultural scheme located in the Eastern Region of Saudi Arabia. Landsat-8 and Sentinel-2 satellite images were acquired during the potato growth stages and two vegetation indices (the normalized difference vegetation index (NDVI) and the soil adjusted vegetation index (SAVI)) were generated from the images. Vegetation index maps were developed and classified into zones based on vegetation health statements, where the stratified random sampling points were accordingly initiated. Potato yield samples were collected 2-3 days prior to the harvest time and were correlated to the adjacent NDVI and SAVI, where yield prediction algorithms were developed and used to generate prediction yield maps. Results of the study revealed that the difference between predicted yield values and actual ones (prediction error) ranged between 7.9 and 13.5% for Landsat-8 images and between 3.8 and 10.2% for Sentinel-2 images. The relationship between actual and predicted yield values produced R2 values ranging between 0.39 and 0.65 for Landsat-8 images and between 0.47 and 0.65 for Sentinel-2 images. Results of this study revealed a considerable variation in field productivity across the three fields, where high-yield areas produced an average yield of above 40 t ha-1; while, the low-yield areas produced, on the average, less than 21 t ha-1. Identifying such great variation in field productivity will assist farmers and decision makers in managing their practices.

  19. Prediction of Potato Crop Yield Using Precision Agriculture Techniques

    Science.gov (United States)

    Al-Gaadi, Khalid A.; Hassaballa, Abdalhaleem A.; Tola, ElKamil; Kayad, Ahmed G.; Madugundu, Rangaswamy; Alblewi, Bander; Assiri, Fahad

    2016-01-01

    Crop growth and yield monitoring over agricultural fields is an essential procedure for food security and agricultural economic return prediction. The advances in remote sensing have enhanced the process of monitoring the development of agricultural crops and estimating their yields. Therefore, remote sensing and GIS techniques were employed, in this study, to predict potato tuber crop yield on three 30 ha center pivot irrigated fields in an agricultural scheme located in the Eastern Region of Saudi Arabia. Landsat-8 and Sentinel-2 satellite images were acquired during the potato growth stages and two vegetation indices (the normalized difference vegetation index (NDVI) and the soil adjusted vegetation index (SAVI)) were generated from the images. Vegetation index maps were developed and classified into zones based on vegetation health statements, where the stratified random sampling points were accordingly initiated. Potato yield samples were collected 2–3 days prior to the harvest time and were correlated to the adjacent NDVI and SAVI, where yield prediction algorithms were developed and used to generate prediction yield maps. Results of the study revealed that the difference between predicted yield values and actual ones (prediction error) ranged between 7.9 and 13.5% for Landsat-8 images and between 3.8 and 10.2% for Sentinel-2 images. The relationship between actual and predicted yield values produced R2 values ranging between 0.39 and 0.65 for Landsat-8 images and between 0.47 and 0.65 for Sentinel-2 images. Results of this study revealed a considerable variation in field productivity across the three fields, where high-yield areas produced an average yield of above 40 t ha-1; while, the low-yield areas produced, on the average, less than 21 t ha-1. Identifying such great variation in field productivity will assist farmers and decision makers in managing their practices. PMID:27611577

  20. Full-field measurements and identification in solid mechanics

    CERN Document Server

    Grediac, Michel

    2008-01-01

    This timely book presents cutting-edge developments by experts in the field on the rapidly developing and scientifically challenging area of full-field measurement techniques used in solid mechanics - including photoelasticity, grid methods, deflectometry, holography, speckle interferometry and digital image correlation. The evaluation of strains and the use of the measurements in subsequent parameter identification techniques to determine material properties are also presented. Since parametric identification techniques require a close coupling of theoretical models and experimental measurements, the book focuses on specific modeling approaches that include finite element model updating, the equilibrium gap method, constitutive equation gap method, virtual field method and reciprocity gap method. In the latter part of the book, the authors discuss two particular applications of selected methods that are of special interest to many investigators: the analysis of localized phenomenon and connections between mi...

  1. Full-field optical coherence tomography apply in sphere measurements

    Science.gov (United States)

    Shi, Wei; Li, Weiwei; li, Juncheng; Wang, Jingyu; Wang, Jianguo

    2016-10-01

    The geometry of a spherical surface, for example that of a precision optic, is completely determined by the radius -of-curvature at one point and the deviation from the perfect spherical form at all other points of the sphere. Full-field Optical Coherence Tomography (FF-OCT) is a parallel detection OCT technique that utilizes a 2D detector array. This technique avoids mechanical scanning in imaging optics, thereby speeding up the imaging process and enhancing the quality of images. The current paper presents an FF-OCT instrument that is designed to be used in sphere measurement with the principle of multiple delays (MD) OCT to evaluate the curvature and radius of curved objects in single-shot imaging. The optimum combination of the MD principle with the FF-OCT method was evaluated, and the radius of a metal ball was measured with this method. The generated 2n-1 contour lines were obtained by using an MDE with n delays in a single en-face OCT image. This method of measurement, it engaged in the measurement accuracy of spherical and enriches the means of measurement, to make a spherical scan techniques flexible application.

  2. Large area full-field optical coherence tomography

    Science.gov (United States)

    Chang, Shoude; Sherif, Sherif; Flueraru, Costel

    2006-09-01

    Optical Coherence Tomography (OCT) is a fundamentally new type of optical imaging technology. OCT performs high resolution, cross-sectional tomographic imaging of the internal structure in materials and biological systems. The biomedical applications of the OCT imaging systems have been developed for diagnostics of ophthalmology, dermatology, dentistry and cardiology. Most of existing OCT systems use point-scanning based technology, however, the 3-axis scanning makes the system slow and cumbersome. A few OCT systems working directly on 2D full-field images were reported, however, they are designed to work in a relatively small area, around couple of hundred microns square. In this paper, we present a design and implementation of a full-field OCT imaging system for acquiring tomography and with a working area around 15mm by 15 mm. The problems rising from full-field OCT are addressed and analyzed. The algorithms to extract the tomography are proposed. Two applications of multilayer information retrieval and 3D object imaging using full-field OCT are described.

  3. Volumetric breast density estimation from full-field digital mammograms.

    NARCIS (Netherlands)

    Engeland, S. van; Snoeren, P.R.; Huisman, H.J.; Boetes, C.; Karssemeijer, N.

    2006-01-01

    A method is presented for estimation of dense breast tissue volume from mammograms obtained with full-field digital mammography (FFDM). The thickness of dense tissue mapping to a pixel is determined by using a physical model of image acquisition. This model is based on the assumption that the breast

  4. Precise full-field distortion rectification and evaluation method for a digital projector

    Science.gov (United States)

    Wang, Zhangying; Liu, Miao; Yang, Shourui; Huang, Shujun; Bai, Xuefei; Liu, Xiaohong; Zhu, Jigui; Liu, Xiaoli; Zhang, Zonghua

    2016-10-01

    Digital projectors have been widely used in many accuracy-sensitive fields. Although some calibration methods have been proposed to obtain the intrinsic parameters for a digital projector, especially the radial and tangential distortion, there are few studies on how to rectify the projected image to obtain an ideal projection pattern and further evaluate the results. In this paper, a precise full-field image rectification technique is proposed based on the principle of projector calibration. The pixel remapping and interpolation techniques are detailed step by step. All of the method's steps maintain subpixel accuracy. Moreover, a full-field verification method is presented to evaluate the effectiveness of the projector distortion procedure using a full-field phase map. A full-field non-linear distortion distribution map can be generated to represent distortion characteristics of nearly all the pixels of a projector in a very intuitive way. The experimental results validate and show the effectiveness of the proposed full-field rectification technique and evaluation method.

  5. Full-field digital image correlation with Kriging regression

    Science.gov (United States)

    Wang, Dezhi; DiazDelaO, F. A.; Wang, Weizhuo; Mottershead, John E.

    2015-04-01

    A full-field Digital Image Correlation (DIC) method with integrated Kriging regression is presented in this article. The displacement field is formulated as a best linear unbiased model that includes the correlations between all the locations in the Region of Interest (RoI). A global error factor is employed to extend conventional Kriging interpolation to quantify displacement errors of the control points. An updating strategy for the self-adaptive control grid is developed on the basis of the Mean Squared Error (MSE) determined from the Kriging model. Kriging DIC is shown to outperform several other full-field DIC methods when using open-access experimental data. Numerical examples are used to demonstrate the robustness of Kriging DIC to different choices of initial control points and to speckle pattern variability. Finally Kriging DIC is tested on an experimental example.

  6. High-yield biopsy technique for subepidermal blisters.

    Science.gov (United States)

    Braswell, Mark A; McCowan, Nancye K; Schulmeier, Jennifer S; Brodell, Robert T

    2015-04-01

    Dermatologists often perform 2 biopsies in patients with widespread tense blisters: one for light microscopy and another for direct immunofluorescence (DIF). Biopsy techniques recommended for blistering diseases with tense blisters are discussed, and illustrations demonstrate an alternative approach utilizing a single punch biopsy. A single punch biopsy is more cost effective and provides the same diagnostic information as the standard 2-biopsy approach for subepidermal blisters plus additional salt-split skin-like diagnostic information. A limitation for bisecting the single punch biopsy specimen is a potential complete separation of the epidermis from the dermis. The single punch biopsy technique is a simple cost-effective method for obtaining necessary diagnostic information when sampling tense blisters in patients with blistering diseases.

  7. Mammographic Artifacts on Full-Field Digital Mammography

    OpenAIRE

    Choi, Jae Jeong; Kim, Sung Hun; Kang, Bong Joo; Choi, Byung Gil; Song, ByungJoo; Jung, Haijo

    2013-01-01

    This study investigates the incidence of full-field digital mammographic (FFDM) artifacts with three systems at two institutions and compares the artifacts between two detector types and two grid types. A total of 4,440 direct and 4,142 indirect FFDM images were reviewed by two radiologists, and artifacts were classified as patient related, hardware related, and software processing. The overall incidence of FFDM artifacts was 3.4 % (292/8,582). Patient related artifacts (motion artifacts and ...

  8. Full-field hard x-ray microscopy with interdigitated silicon lenses

    DEFF Research Database (Denmark)

    Simons, Hugh; Stöhr, Frederik; Michael-Lindhard, Jonas

    2016-01-01

    Full-field x-ray microscopy using x-ray objectives has become a mainstay of the biological and materials sciences. However, the inefficiency of existing objectives at x-ray energies above 15 keV has limited the technique to weakly absorbing or two-dimensional (2D) samples. Here, we show...

  9. The Virtual Fields Method Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements

    CERN Document Server

    Pierron, Fabrice

    2012-01-01

    The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is the first book on the Virtual Fields Method (VFM), a technique to identify materials mechanical properties from full-field measurements. Firmly rooted with extensive theoretical description of the method, the book presents numerous examples of application to a wide range of materials (composites, metals, welds, biomaterials) and situations (static, vibration, high strain rate). The authors give a detailed training section with examples of progressive difficulty to lead the reader to program the VFM and include a set of commented Matlab programs as well as GUI Matlab-based software for more general situations. The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is an ideal book for researchers, engineers, and students interested in applying the VFM to new situations motivated by their research.  

  10. A high-resolution full-field range imaging system

    Science.gov (United States)

    Carnegie, D. A.; Cree, M. J.; Dorrington, A. A.

    2005-08-01

    There exist a number of applications where the range to all objects in a field of view needs to be obtained. Specific examples include obstacle avoidance for autonomous mobile robots, process automation in assembly factories, surface profiling for shape analysis, and surveying. Ranging systems can be typically characterized as being either laser scanning systems where a laser point is sequentially scanned over a scene or a full-field acquisition where the range to every point in the image is simultaneously obtained. The former offers advantages in terms of range resolution, while the latter tend to be faster and involve no moving parts. We present a system for determining the range to any object within a camera's field of view, at the speed of a full-field system and the range resolution of some point laser scans. Initial results obtained have a centimeter range resolution for a 10 second acquisition time. Modifications to the existing system are discussed that should provide faster results with submillimeter resolution.

  11. Mammographic artifacts on full-field digital mammography.

    Science.gov (United States)

    Choi, Jae Jeong; Kim, Sung Hun; Kang, Bong Joo; Choi, Byung Gil; Song, ByungJoo; Jung, Haijo

    2014-04-01

    This study investigates the incidence of full-field digital mammographic (FFDM) artifacts with three systems at two institutions and compares the artifacts between two detector types and two grid types. A total of 4,440 direct and 4,142 indirect FFDM images were reviewed by two radiologists, and artifacts were classified as patient related, hardware related, and software processing. The overall incidence of FFDM artifacts was 3.4% (292/8,582). Patient related artifacts (motion artifacts and skin line artifacts) were the most commonly detected types (1.7%). Underexposure among hardware related artifacts and high-density artifacts among software processing artifacts also were common (0.7 and 0.5%, respectively). These artifacts, specific to digital mammography, were more common with the direct detector type and the crossed air grid type than with the indirect type and linear grid type (p artifacts on FFDM were patient related, which might be controlled by the instruction of a patient and technologist. Underexposure and high-density artifacts were more common with direct detector and crossed air type of grid.

  12. Technology evaluation center assessment synopsis: full-field digital mammography.

    Science.gov (United States)

    Rothenberg, Barbara M; Ziegler, Kathleen M; Aronson, Naomi

    2006-08-01

    Full-field digital mammography (FFDM) is proposed as an alternative to screen-film mammography (SFM). The ability to separate and optimize the acquisition, storage, and display of images may allow greater visualization of breast cancers at equal or lower radiation doses, especially in younger women and those with denser breasts. This is a synopsis of a systematic review by the Blue Cross Blue Shield Association Technology Evaluation Center. This updated systematic review primarily incorporated the results of the ACR Imaging Network(R) Digital Mammographic Imaging Screening Trial (DMIST), which provided results on 42,760 asymptomatic women who underwent both FFDM and SFM and showed with reasonable certainty that there was no difference in the accuracy of the 2 modalities for asymptomatic women in general, with some advantages of FFDM in certain subgroups. There were no strong, new studies on the use of digital mammography compared with film mammography in a diagnostic population. However, the DMIST results indicated that tumors detected by FFDM, but not by SFM, were likely to be invasive carcinomas or medium-grade to high-grade ductal carcinoma in situ. On the basis of the suppositions that these are the cancers of greatest interest and the ones more likely to be found in a diagnostic population and that the diagnostic population may be younger on average than the screening population, it was concluded that there is sufficient evidence to support the use of FFDM for diagnostic purposes.

  13. Direct Strain Tensor Approximation for Full-Field Strain Measurement Methods

    Science.gov (United States)

    2013-01-01

    of grating coordinates using correlation filter techniques. Optik 1988; 80:76–79. 3. Bruck H, McNeill S, Sutton M, Peters W. Digital image correlation...record.url?eid=2-s2.0-46949097860&partnerID=40&md5= 25dddce389c9640db7cf8fbf3c50dc4e. 27. Cheng P, Sutton M, Schreier H, McNeill S. Full-field speckle

  14. Physical characteristics of a full-field digital mammography system

    Science.gov (United States)

    Suryanarayanan, Sankararaman; Karellas, Andrew; Vedantham, Srinivasan

    2004-11-01

    The physical performance characteristics of a flat-panel clinical full-field digital mammography (FFDM) system were investigated for a variety of mammographic X-ray spectral conditions. The system was investigated using 26 kVp: Mo/Mo, 28 kVp: Mo/Rh, and 30 kVp: Rh/Rh, with polymethyl methacrylate (PMMA) "tissue equivalent material" of thickness 20, 45, and 60 mm for each of three X-ray spectra, resulting in nine different spectral conditions. The experimental results were compared with a theoretical cascaded linear systems-based model that has been developed independently by other investigators. The FFDM imager (Senographe 2000D, GE Medical Systems, Milwaukee, WI) uses an amorphous silicon (aSi:H) photodiode (100 μm pixel) array directly coupled to a cesium iodide (CsI) scintillator. The spatial resolution of the digital mammography system was determined by measuring the presampling modulation transfer function (MTF). The noise power spectra (NPS) of the system were measured under the different mammographic X-ray spectral conditions at an exposure of approximately 10 mR to the detector from which corresponding detective quantum efficiencies (DQE) were determined. The experimental results provide additional information on the performance of the mammographic system for a broader range of experimental conditions than have been reported in the past. The flat-panel imager exhibits favorable physical quality characteristics under the conditions investigated. The experimental results were compared with theoretical estimates under various spectral conditions and demonstrated good agreement.

  15. Full-field Measurement of Deformation and Vibration using Digital Image Correlation

    Directory of Open Access Journals (Sweden)

    Liang-Chih Chen

    2015-05-01

    Full Text Available The main intention of this study was to investigate the full-field measurement of de-formation and vibration using a program we developed for digital image correlation. Digital image correlation is a measuring method that can calculate the displacement of each point on an object by using recorded images. By capturing continuous images of the object in deformation or in motion, the displacements of feature points on the object can be tracked and used in calculations to determine the full-field deformation, strain and vibration of the object. We used the fast and simple algorithm in our program as the core, and conducted non-contact full-field displacement measurement by tracking feature points from images taken after motion. The measuring accuracy can be up to 0.1 pixel. Our experimental results show the technique to be very accurate and useful. We also applied this technique under conditions where an ordinary sensor could not be used.

  16. Full-field dye concentration measurement within saturated/unsaturated thin slabs of porous media

    Energy Technology Data Exchange (ETDEWEB)

    Norton, D.L. [Arizona Univ., Tucson, AZ (United States). Dept. of Hydrology; Glass, R.J. [Sandia National Labs., Albuquerque, NM (United States)

    1992-12-31

    This paper presents a full-field dye concentration measurement technique that extends our experimental capabilities to the measurement of transient dye concentration fields within steady state flow fields under unsaturated or saturated conditions. Simple light absorption theory provides a basis for translating images into high resolution dye concentration fields. A series of dye pulse experiments that demonstrate the combined use of the full-field saturation and dye concentration techniques was conducted at four different degrees of saturation. Each of these experimental sequences was evaluated with respect to mass balance, the results being within 5% of the known dye mass input. An image windowing technique allowed us to see increased dispersion due to decreasing moisture content, tailing of concentration at the rear of the dye pulse and slight velocity changes of the dispersive front due to changes in moisture content. The exceptional resolution of dye concentration in space and time provided by this laboratory technique allows systematic experimentation for examining basic processes affecting solute transport within saturated/unsaturated porous media. Future challenges for this work will be to use these techniques to analyze more complex systems involving heterogeneities, scaling laws, and detailed investigations of the relationship between transverse and longitudinal dispersion in unsaturated media.

  17. Full-field feature profile models in process control

    Science.gov (United States)

    Zavecz, Terrence E.

    2005-05-01

    Most process window analysis applications are capable of deriving the functional focus-dose workspace available to any set of device specifications. Previous work in this area has concentrated on calculating the superpositioned optimum operating points of various combinations of feature orientations or feature types. These studies invariably result in an average performance calculation that is biased by the impact of the substrate, reticle and exposure tool contributed perturbations. Many SEM's and optical metrology tools now provide full-feature profile information for multiple points in the exposure field. The inclusion of field spatial information into the process window analysis results in a calculation of greater accuracy and process understanding because now the capabilities of each exposure tool can be individually modeled and optimized. Such an analysis provides the added benefit that after the exposure tool is characterized, it's process perturbations can be removed from the analysis to provide greater understanding of the true process performance. Process window variables are shown to vary significantly across the exposure field of the scanner. Evaluating the depth-of-focus and optimum focus-dose at each point in the exposure field yields additional information on the imaging response of the reticle and scan-linearity of the exposure tool's reticle stage. The optimal focus response of the reticle is then removed from a full wafer exposure and the results are modeled to obtain a true process response and performance.

  18. Fingerprint imaging from the inside of a finger with full-field optical coherence tomography

    Science.gov (United States)

    Auksorius, Egidijus; Boccara, A. Claude

    2015-01-01

    Imaging below fingertip surface might be a useful alternative to the traditional fingerprint sensing since the internal finger features are more reliable than the external ones. One of the most promising subsurface imaging technique is optical coherence tomography (OCT), which, however, has to acquire 3-D data even when a single en face image is required. This makes OCT inherently slow for en face imaging and produce unnecessary large data sets. Here we demonstrate that full-field optical coherence tomography (FF-OCT) can be used to produce en face images of sweat pores and internal fingerprints, which can be used for the identification purposes. PMID:26601009

  19. Focus defect and dispersion mismatch in full-field optical coherence microscopy.

    Science.gov (United States)

    Dubois, Arnaud

    2017-03-20

    Full-field optical coherence microscopy (FFOCM) is an optical technique, based on low-coherence interference microscopy, for tomographic imaging of semi-transparent samples with micrometer-scale spatial resolution. The differences in refractive index between the sample and the immersion medium of the microscope objectives may degrade the FFOCM image quality because of focus defect and optical dispersion mismatch. These phenomena and their consequences are discussed in this theoretical paper. Experimental methods that have been implemented in FFOCM to minimize the adverse effects of these phenomena are summarized and compared.

  20. High-resistance controlled yielding supporting technique in deep-well oil shale roadways

    Institute of Scientific and Technical Information of China (English)

    Yu Yang; Bai Jianbiao; Wang Xiangyu; Wang Junde; Xue Shizhi; Xu Ke

    2014-01-01

    In order to avoid the deep-well oil shale roadway being deformed, damaged, or difficult to maintain after excavating and supporting in Haishiwan coal mine, this paper has analyzed the characteristics of the deformed roadway and revealed its failure mechanism by taking comprehensively the methods of field geological investigation, displacement monitoring of surrounding rock, rock properties and hydration properties experiments and field application tests. Based on this work, the high-resistance controlled yielding supporting principle is proposed, which is:to‘resist’ by high pre-tightening force and high stiff-ness in the early stage, to‘yield’ by making use of the controlled deformation of a yielding tube in the middle stage, and to‘fix’ by applying total-section Gunite in the later stage. A high-resistance controlled yielding supporting technique of‘high pre-tightening force yielding anchor bolt+small-bore pre-tight-ening force anchor cable+rebar ladder beam+rhombic metal mesh+lagging gunite’ has been estab-lished, and industrial on site testing implemented. The practical results show that the high-resistance controlled yielding supporting technique can effectively control the large deformation and long-time rhe-ology of deep-well oil shale roadways and can provide beneficial references for the maintenance of other con-generic roadways.

  1. Numerical correction of coherence gate in full-field swept-source interference microscopy.

    Science.gov (United States)

    Grebenyuk, Anton A; Ryabukho, Vladimir P

    2012-07-01

    A big problem in low-coherence interference microscopy is the degradation of the coherence signal caused by shift of the angular and temporal spectrum gates. It limits the depth of field in confocal optical coherence microscopy and degrades images of sample inner structure in most interference microscopy techniques. To overcome this problem we propose numerical correction of the coherence gate in application to full-field swept-source interference microscopy. The proposed technique allows three-dimensional sample imaging without mechanical movement of the microscope components and is also capable of determining separately the geometrical thickness and the refractive index of the sample layers, when the sample contains a transversal pattern. The applicability of the proposed technique is verified with numerical simulation.

  2. Surface mapping of field-induced piezoelectric strain at elevated temperature employing full-field interferometry.

    Science.gov (United States)

    Stevenson, Tim; Quast, Tatjana; Bartl, Guido; Schmitz-Kempen, Thorsten; Weaver, Paul M

    2015-01-01

    Piezoelectric actuators and sensors are widely used for flow control valves, including diesel injectors, ultrasound generation, optical positioning, printing, pumps, and locks. Degradation and failure of material and electrical properties at high temperature typically limits these applications to operating temperatures below 200°C, based on the ubiquitous Pb(Zr,Ti)O3 ceramic. There are, however, many applications in sectors such as automotive, aerospace, energy and process control, and oil and gas, where the ability to operate at higher temperatures would open up new markets for piezoelectric actuation. Presented here is a review of recent progress and initial results toward a European effort to develop measurement techniques to characterize high-temperature materials. Full-field, multi-wavelength absolute length interferometry has, for the first time, been used to map the electric-field-induced piezoelectric strain across the surface of a PZT ceramic. The recorded variation as a function of temperature has been evaluated against a newly developed commercial single-beam system. Conventional interferometry allows measurement of the converse piezoelectric effect with high precision and resolution, but is often limited to a single point, average measurement and to limited sample environments because of optical aberrations in varying atmospheres. Here, the full-field technique allows the entire surface to be analyzed for strain and, in a bespoke sample chamber, for elevated temperatures.

  3. Graphene reflux: improving the yield of liquid-exfoliated nanosheets through repeated separation techniques

    Science.gov (United States)

    Rountree, Kyler S.; Shah, Smit A.; Sweeney, Charles B.; Irin, Fahmida; Green, Micah J.

    2016-12-01

    Scalable production of graphene through liquid-phase exfoliation has been plagued by low yields. Although several recent studies have attempted to improve graphene exfoliation technology, the problem of separating colloidal nanosheets from unexfoliated parent material has received far less attention. Here we demonstrate a scalable method for improving nanosheet yield through a facile washing process. By probing the sedimentation of liquid-phase exfoliated slurries of graphene nanosheets and parent material, we found that a portion of exfoliated graphene is entrapped in the sediment, but can be recovered by repeatedly washing the slurry of nanosheet and parent material with additional solvent. We found this process to significantly increase the overall yield of graphene (graphene/parent material) and recover a roughly constant proportion of graphene with each wash. The cumulative amount of graphene recovered is only a function of total solvent volume. Moreover, we found this technique to be applicable to other types of nanosheets such as boron nitride nanosheets.

  4. Full-field micro surface profilometry using digital fringe projection with spatial encoding principle

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L-C [Graduate Institute of Automation Technology, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd, Taipei, 106, Taiwan (China); Liao, C-C [Graduate Institute of Mechatronics, National Taipei University of Technology, 1 Sec. Chung-Hsiao East Rd, Taipei, 106, Taiwan (China); Lai, M-J [Graduate Institute of Mechatronics, National Taipei University of Technology, 1 Sec. Chung-Hsiao East Rd, Taipei, 106, Taiwan (China)

    2005-01-01

    This article describes an effective full-field three-dimensional micro surface profilometer using digital fringe projection with digital micromirror device (DMD) technology and triangulation measurement principle. Fast and accurate three-dimensional measurement techniques with full-field measurement capability are thus highly demanded for sharpening product competitiveness. Traditional laser triangulation methods have difficulty in detecting the accurate centre position of projected points or lines when encountered with light scattering problems caused by the object's geometric discontinuities, such as surface boundaries or edges. The newly developed profilometer deploys a DMD to project flexible digital structured light patterns of white light onto the object to suit various inspection requirements, such as the object's size and surface condition. Micro structured light patterns can be generated by using optical zoom and collimating lens sets. Accurate system parameters of 3-D surface profilometry can be obtained by developing a calibration process based on least squares minimization. Micro 3-D contours with a large surface gradient can be reconstructed accurately and efficiently.

  5. Multimodal full-field optical coherence tomography on biological tissue: toward all optical digital pathology

    Science.gov (United States)

    Harms, F.; Dalimier, E.; Vermeulen, P.; Fragola, A.; Boccara, A. C.

    2012-03-01

    Optical Coherence Tomography (OCT) is an efficient technique for in-depth optical biopsy of biological tissues, relying on interferometric selection of ballistic photons. Full-Field Optical Coherence Tomography (FF-OCT) is an alternative approach to Fourier-domain OCT (spectral or swept-source), allowing parallel acquisition of en-face optical sections. Using medium numerical aperture objective, it is possible to reach an isotropic resolution of about 1x1x1 ìm. After stitching a grid of acquired images, FF-OCT gives access to the architecture of the tissue, for both macroscopic and microscopic structures, in a non-invasive process, which makes the technique particularly suitable for applications in pathology. Here we report a multimodal approach to FF-OCT, combining two Full-Field techniques for collecting a backscattered endogeneous OCT image and a fluorescence exogeneous image in parallel. Considering pathological diagnosis of cancer, visualization of cell nuclei is of paramount importance. OCT images, even for the highest resolution, usually fail to identify individual nuclei due to the nature of the optical contrast used. We have built a multimodal optical microscope based on the combination of FF-OCT and Structured Illumination Microscopy (SIM). We used x30 immersion objectives, with a numerical aperture of 1.05, allowing for sub-micron transverse resolution. Fluorescent staining of nuclei was obtained using specific fluorescent dyes such as acridine orange. We present multimodal images of healthy and pathological skin tissue at various scales. This instrumental development paves the way for improvements of standard pathology procedures, as a faster, non sacrificial, operator independent digital optical method compared to frozen sections.

  6. Application of GEM-based detectors in full-field XRF imaging

    Science.gov (United States)

    Dąbrowski, W.; Fiutowski, T.; Frączek, P.; Koperny, S.; Lankosz, M.; Mendys, A.; Mindur, B.; Świentek, K.; Wiącek, P.; Wróbel, P. M.

    2016-12-01

    X-ray fluorescence spectroscopy (XRF) is a commonly used technique for non-destructive elemental analysis of cultural heritage objects. It can be applied to investigations of provenance of historical objects as well as to studies of art techniques. While the XRF analysis can be easily performed locally using standard available equipment there is a growing interest in imaging of spatial distribution of specific elements. Spatial imaging of elemental distrbutions is usually realised by scanning an object with a narrow focused X-ray excitation beam and measuring characteristic fluorescence radiation using a high energy resolution detector, usually a silicon drift detector. Such a technique, called macro-XRF imaging, is suitable for investigation of flat surfaces but it is time consuming because the spatial resolution is basically determined by the spot size of the beam. Another approach is the full-field XRF, which is based on simultaneous irradiation and imaging of large area of an object. The image of the investigated area is projected by a pinhole camera on a position-sensitive and energy dispersive detector. The infinite depth of field of the pinhole camera allows one, in principle, investigation of non-flat surfaces. One of possible detectors to be employed in full-field XRF imaging is a GEM based detector with 2-dimensional readout. In the paper we report on development of an imaging system equipped with a standard 3-stage GEM detector of 10 × 10 cm2 equipped with readout electronics based on dedicated full-custom ASICs and DAQ system. With a demonstrator system we have obtained 2-D spatial resolution of the order of 100 μm and energy resolution at a level of 20% FWHM for 5.9 keV . Limitations of such a detector due to copper fluorescence radiation excited in the copper-clad drift electrode and GEM foils is discussed and performance of the detector using chromium-clad electrodes is reported.

  7. Fast full-field OCT assessment of clinical tissue specimens (Conference Presentation)

    Science.gov (United States)

    Dalimier, Eugénie; Harms, Fabrice; Brossolet, Charles; Benoit, Emilie; Martins, Franck; Boccara, Claude

    2016-03-01

    Full-field optical coherence tomography (FFOCT) offers a non-invasive method of obtaining images of biological tissues at ultrahigh resolution (1µm in all 3 directions) approaching traditional histological sections. Previous clinical studies have shown the high efficiency of this imaging technique for the detection of cancer on various organs. This promises great potential of the technique for an ex-vivo quick analysis of surgical resections or biopsy specimens, in the aim to help the surgeon/radiologist decide on the course of action. Here we will present some of the latest technical developments on a FFOCT system which can produce 1cm2 images with 1 µm resolution in 1 minute. Larger samples, up to 50mm diameter, can also be imaged. Details on the large sample handling, high-speed image acquisition, optimized scanning, and accelerated GPU tiles stitching will be given. Results on the clinical applications for breast, urology, and digestive tissues will also be given. They highlight the relevance of the system characteristics for the detection of cancer on ex-vivo specimens. FFOCT now appears clearly as a very fast and non-destructive imaging technique that provides a quick assessment of the tissue morphology. With the benefit of both new technical developments and clinical validation, it turned into a mature technique to be implemented in the clinical environment. In particular, the technique holds potential for the fast ex-vivo analysis of excision margins or biopsies in the operating room.

  8. Dynamic full field optical coherence tomography: subcellular metabolic contrast revealed in tissues by temporal analysis of interferometric signals

    CERN Document Server

    Apelian, Clement; Thouvenin, Olivier; Boccara, A Claude

    2016-01-01

    We developed a new endogenous approach to reveal subcellular metabolic contrast in fresh ex vivo tissues taking advantage of the time dependence of the full field optical coherence tomography interferometric signals. This method reveals signals linked with local activity of the endogenous scattering elements which can reveal cells where other imaging techniques fail or need exogenous contrast agents. We benefit from the micrometric transverse resolution of full field OCT to image intracellular features. We used this time dependence to identify different dynamics at the millisecond scale on a wide range of organs in normal or pathological conditions.

  9. A domain decomposition approach for full-field measurements based identification of local elastic parameters

    KAUST Repository

    Lubineau, Gilles

    2015-03-01

    We propose a domain decomposition formalism specifically designed for the identification of local elastic parameters based on full-field measurements. This technique is made possible by a multi-scale implementation of the constitutive compatibility method. Contrary to classical approaches, the constitutive compatibility method resolves first some eigenmodes of the stress field over the structure rather than directly trying to recover the material properties. A two steps micro/macro reconstruction of the stress field is performed: a Dirichlet identification problem is solved first over every subdomain, the macroscopic equilibrium is then ensured between the subdomains in a second step. We apply the method to large linear elastic 2D identification problems to efficiently produce estimates of the material properties at a much lower computational cost than classical approaches.

  10. Full-field hard x-ray microscopy with interdigitated silicon lenses

    CERN Document Server

    Simons, Hugh; Michael-Lindhard, Jonas; Jensen, Flemming; Hansen, Ole; Detlefs, Carsten; Poulsen, Henning Friis

    2015-01-01

    Full-field x-ray microscopy using x-ray objectives has become a mainstay of the biological and materials sciences. However, the inefficiency of existing objectives at x-ray energies above 15 keV has limited the technique to weakly absorbing or two-dimensional (2D) samples. Here, we show that significant gains in numerical aperture and spatial resolution may be possible at hard x-ray energies by using silicon-based optics comprising 'interdigitated' refractive silicon lenslets that alternate their focus between the horizontal and vertical directions. By capitalizing on the nano-manufacturing processes available to silicon, we show that it is possible to overcome the inherent inefficiencies of silicon-based optics and interdigitated geometries. As a proof-of-concept of Si-based interdigitated objectives, we demonstrate a prototype interdigitated lens with a resolution of ~255 nm at 17 keV.

  11. Predicting the yield of {sup 177}Lu radionuclide produced by the cyclic irradiation technique

    Energy Technology Data Exchange (ETDEWEB)

    Odame Duodu, Godfred, E-mail: jogd14@yahoo.co [Radiological and Medical Sciences Research Institute, Ghana Atomic Energy Commission, P.O. Box LG80, Legon Accra (Ghana); Akaho, Edward H.K.; Serfor-Armah, Yaw [Ghana Atomic Energy Commission, P.O. Box LG80, Legon Accra (Ghana); Nyarko, Benjamin J.B. [National Nuclear Research Institute, Ghana Atomic Energy Commission, P.O. Box LG80, Legon Accra (Ghana); Afi Achoribo, Elom [Radiological and Medical Sciences Research Institute, Ghana Atomic Energy Commission, P.O. Box LG80, Legon Accra (Ghana)

    2011-03-15

    The feasibility study on the production of {sup 177}Lu radioisotope using a low power research reactor has been conducted. A reliable method for predicting the yield of {sup 177}Lu produced using the cyclic activation technique based on the Westcott formalism has been established. A specific activity of 243.24 mCi/g was obtained when a {sup 176}Lu{sub 2}O{sub 3} of natural abundance was irradiated for 4 h and decayed for 20 h for four cycles at GHARR-1 with a neutron flux of 5.0x10{sup 11} ncm{sup -2} s{sup -1}.

  12. Regressions by leaps and bounds and biased estimation techniques in yield modeling

    Science.gov (United States)

    Marquina, N. E. (Principal Investigator)

    1979-01-01

    The author has identified the following significant results. It was observed that OLS was not adequate as an estimation procedure when the independent or regressor variables were involved in multicollinearities. This was shown to cause the presence of small eigenvalues of the extended correlation matrix A'A. It was demonstrated that the biased estimation techniques and the all-possible subset regression could help in finding a suitable model for predicting yield. Latent root regression was an excellent tool that found how many predictive and nonpredictive multicollinearities there were.

  13. Application of Vegetation Indices for Agricultural Crop Yield Prediction Using Neural Network Techniques

    Directory of Open Access Journals (Sweden)

    Suranjan Panigrahi

    2010-03-01

    Full Text Available Spatial variability in a crop field creates a need for precision agriculture. Economical and rapid means of identifying spatial variability is obtained through the use of geotechnology (remotely sensed images of the crop field, image processing, GIS modeling approach, and GPS usage and data mining techniques for model development. Higher-end image processing techniques are followed to establish more precision. The goal of this paper was to investigate the strength of key spectral vegetation indices for agricultural crop yield prediction using neural network techniques. Four widely used spectral indices were investigated in a study of irrigated corn crop yields in the Oakes Irrigation Test Area research site of North Dakota, USA. These indices were: (a red and near-infrared (NIR based normalized difference vegetation index (NDVI, (b green and NIR based green vegetation index (GVI, (c red and NIR based soil adjusted vegetation index (SAVI, and (d red and NIR based perpendicular vegetation index (PVI. These four indices were investigated for corn yield during 3 years (1998, 1999, and 2001 and for the pooled data of these 3 years. Initially, Back-propagation Neural Network (BPNN models were developed, including 16 models (4 indices * 4 years including the data from the pooled years to test for the efficiency determination of those four vegetation indices in corn crop yield prediction. The corn yield was best predicted using BPNN models that used the means and standard deviations of PVI grid images. In all three years, it provided higher prediction accuracies, coefficient of determination (r2, and lower standard error of prediction than the models involving GVI, NDVI, and SAVI image information. The GVI, NDVI, and SAVI models for all three years provided average testing prediction accuracies of 24.26% to 94.85%, 19.36% to 95.04%, and 19.24% to 95.04%, respectively while the PVI models for all three years provided average testing prediction accuracies

  14. Biomechanical caracterisation of lumbar belt by full-field techniques: Preliminary results

    CERN Document Server

    Bonnaire, Rebecca; Calmels, Paul; Convert, Reynald

    2013-01-01

    In France, 50% of the population per year is suffering from low back pain. Lumbar belt are frequently proposed as a part of the treatment of this pathology. However mechanical ways of working of this medical device is not clearly understood, but abdominal pressure is often related. So an optical method was developed in this study to measure strain in lumbar belt and trunk interface and to derive a pressure estimation. Optical method consisted of coupling fringe projection and digital image correlation (DIC). Measurement has been carried out on the right side of a manikin wearing a lumbar belt. Average strain is 0.2 and average pressure is 1 kPa. Continuation of this study will be comparison of strain and pressure in different areas of lumbar belt (left side, front and back) and comparison of different lumbar belts. Results will be used in a finite elements model to determine lumbar belt impact in intern body. In long term, this kind of study will be done on human.

  15. Extracting full-field dynamic strain response of a rotating wind turbine using photogrammetry

    Science.gov (United States)

    Baqersad, Javad; Poozesh, Peyman; Niezrecki, Christopher; Avitabile, Peter

    2015-04-01

    Health monitoring of wind turbines is typically performed using conventional sensors (e.g. strain-gages and accelerometers) that are usually mounted to the nacelle or gearbox. Although many wind turbines stop operating due to blade failures, there are typically few to no sensor mounted on the blades. Placing sensors on the rotating parts of the structure is a challenge due to the wiring and data transmission constraints. Within the current work, an approach to monitor full-field dynamic response of rotating structures (e.g. wind turbine blades or helicopter rotors) is developed and experimentally verified. A wind turbine rotor was used as the test structure and was mounted to a block and horizontally placed on the ground. A pair of bearings connected to the rotor shaft allowed the turbine to freely spin along the shaft. Several optical targets were mounted to the blades and a pair of high-speed cameras was used to monitor the dynamics of the spinning turbine. Displacements of the targets during rotation were measured using three-dimensional point tracking. The point tracking technique measured both rigid body displacement and flexible deformation of the blades at target locations. While the structure is rotating, only flap displacements of optical targets (displacements out of the rotation plane) were used in strain prediction process. The measured displacements were expanded and applied to the finite element model of the turbine to extract full-field dynamic strain on the structure. The proposed approach enabled the prediction of dynamic response on the outer surface as well as within the inner points of the structure where no other sensor could be easily mounted. In order to validate the proposed approach, the predicted strain was compared to strain measured at four locations on the spinning blades using a wireless strain-gage system.

  16. Actinic imaging of native and programmed defects on a full-field mask

    Energy Technology Data Exchange (ETDEWEB)

    Mochi, I.; Goldberg, K. A.; Fontaine, B. La; Tchikoulaeva, A.; Holfeld, C.

    2010-03-12

    We describe the imaging and characterization of native defects on a full field extreme ultraviolet (EUV) mask, using several reticle and wafer inspection modes. Mask defect images recorded with the SEMA TECH Berkeley Actinic Inspection Tool (AIT), an EUV-wavelength (13.4 nm) actinic microscope, are compared with mask and printed-wafer images collected with scanning electron microscopy (SEM) and deep ultraviolet (DUV) inspection tools. We observed that defects that appear to be opaque in the SEM can be highly transparent to EUV light, and inversely, defects that are mostly transparent to the SEM can be highly opaque to EUV. The nature and composition of these defects, whether they appear on the top surface, within the multilayer coating, or on the substrate as buried bumps or pits, influences both their significance when printed, and their detectability with the available techniques. Actinic inspection quantitatively predicts the characteristics of printed defect images in ways that may not be possible with non-EUV techniques. As a quantitative example, we investigate the main structural characteristics of a buried pit defect based on EUV through-focus imaging.

  17. Adaptive automatic data analysis in full-field fringe-pattern-based optical metrology

    Science.gov (United States)

    Trusiak, Maciej; Patorski, Krzysztof; Sluzewski, Lukasz; Pokorski, Krzysztof; Sunderland, Zofia

    2016-12-01

    Fringe pattern processing and analysis is an important task of full-field optical measurement techniques like interferometry, digital holography, structural illumination and moiré. In this contribution we present several adaptive automatic data analysis solutions based on the notion of Hilbert-Huang transform for measurand retrieval via fringe pattern phase and amplitude demodulation. The Hilbert-Huang transform consists of 2D empirical mode decomposition algorithm and Hilbert spiral transform analysis. Empirical mode decomposition adaptively dissects a meaningful number of same-scale subimages from the analyzed pattern - it is a data-driven method. Appropriately managing this set of unique subimages results in a very powerful fringe pre-filtering tool. Phase/amplitude demodulation is performed using Hilbert spiral transform aided by the local fringe orientation estimator. We describe several optical measurement techniques for technical and biological objects characterization basing on the especially tailored Hilbert-Huang algorithm modifications for fringe pattern denoising, detrending and amplitude/phase demodulation.

  18. Full-field AO-assisted OCT for high-resolution tomographic imaging of the retina

    Science.gov (United States)

    Glanc, M.; Lafaille, D.; Puget, P.; Lacombe, F.; Vabre, L.; Levecq, X.; Chateau, N.

    2006-02-01

    Since the advent of Adaptive Optics in ophthalmic instrumentation, several attempts for improving the performances of the existing observing techniques, either in imaging or tomography, have been made. For long, Adaptive Optics have proven its ability to restore high lateral resolution with the SLO or flood imaging, or more recently to enhance the interferometric contrast and hence, the sensitivity, of OCT. Nevertheless, the direct acquisition of en face tomographic images equivalent to horizontal optical sections of the retinal tissue is still the objective of intensive developments. We report here a new instrumental approach where a time domain full field OCT setup has been coupled with a double pass adaptive optics system, providing 300 x 300 x 4 m instantaneous optical sections of biological tissues. We will describe how the interferometric contrast is derived without any modulation of the optical path, thus giving access to targets as critical, because unstable, as the retinal tissue during in vivo ophthalmic examinations. The advantages of this new design, which benefits from the implementation of very recent deformable mirrors, featuring simultaneously a higher actuators density and a much larger stroke, will be discussed, and the ability of the system to accommodate for variable pupil sizes, thanks to wavefront sensing techniques optimized for ophthalmology, are commented. The performances of the system, in terms of X,Y,Z resolution, sensitivity, registration capability and / or image stabilisation are discussed and illustrated with results obtained in the laboratory and in clinical environment.

  19. Rapid full-field OCT assessment of clinical tissue specimens (Conference Presentation)

    Science.gov (United States)

    Dalimier, Eugénie; Harms, Fabrice; Brossollet, Charles; Benoit, Emilie; Martins, Franck; Boccara, Claude A.

    2016-03-01

    FFOCT (Full Field Optical Coherence Tomography) is a novel optical technology that gives access to very high resolution tomography images of biological tissues within minutes, non-invasively. This makes it an attractive tool to bridge the gap between medical imaging modalities (MRI, ultrasound, CT) used for cancer lesion identification or targeting and histological diagnosis. Clinical tissue specimens, such as surgical cancer margins or biopsies, can potentially be assessed rapidly, by the clinician, in the aim to help him decide on the course of action. A fast FFOCT prototype was built, that provides 1cm2 images with 1 µm resolution in 1 minute, and can accommodate samples up to 50mm diameter. Specific work was carried out to implement a large sample holder, high-speed image acquisition system, optimized scanning, and accelerated GPU tiles stitching. Results obtained on breast, urology, and digestive tissues show the efficiency of the technique for the detection of cancer on clinical tissue specimens, and reinforce the clinical relevance of the technique. The technical and clinical results show that the fast FFOCT system can successfully be used for a fast assessment of cancer excision margins or biopsies providing a very valuable tool in the clinical environment.

  20. Full-field dynamic characterization of superhydrophobic condensation on biotemplated nanostructured surfaces.

    Science.gov (United States)

    Ölçeroğlu, Emre; Hsieh, Chia-Yun; Rahman, Md Mahamudur; Lau, Kenneth K S; McCarthy, Matthew

    2014-07-01

    While superhydrophobic nanostructured surfaces have been shown to promote condensation heat transfer, the successful implementation of these coatings relies on the development of scalable manufacturing strategies as well as continued research into the fundamental physical mechanisms of enhancement. This work demonstrates the fabrication and characterization of superhydrophobic coatings using a simple scalable nanofabrication technique based on self-assembly of the Tobacco mosaic virus (TMV) combined with initiated chemical vapor deposition. TMV biotemplating is compatible with a wide range of surface materials and applicable over large areas and complex geometries without the use of any power or heat. The virus-structured coatings fabricated here are macroscopically superhydrophobic (contact angle >170°) and have been characterized using environmental electron scanning microscopy showing sustained and robust coalescence-induced ejection of condensate droplets. Additionally, full-field dynamic characterization of these surfaces during condensation in the presence of noncondensable gases is reported. This technique uses optical microscopy combined with image processing algorithms to track the wetting and growth dynamics of 100s to 1000s of microscale condensate droplets simultaneously. Using this approach, over 3 million independent measurements of droplet size have been used to characterize global heat transfer performance as a function of nucleation site density, coalescence length, and the apparent wetted surface area during dynamic loading. Additionally, the history and behavior of individual nucleation sites, including coalescence events, has been characterized. This work elucidates the nature of superhydrophobic condensation and its enhancement, including the role of nucleation site density during transient operation.

  1. Development of PZT-excited stroboscopic shearography for full-field nondestructive evaluation

    Science.gov (United States)

    Asemani, Hamidreza; Park, Jinwoo; Lee, Jung-Ryul; Soltani, Nasser

    2017-05-01

    Nondestructive evaluation using shearography requires a way to stress the inspection target. This technique is able to directly measure the displacement gradient distribution on the object surface. Shearography visualizes the internal structural damages as the anomalous pattern in the shearograpic fringe pattern. A piezoelectric (PZT) excitation system is able to generate loadings in the vibrational, acoustic, and ultrasonic regimes. In this paper, we propose a PZT-excited stroboscopic shearography. The PZT excitation could generate vibrational loading, a stationary wavefield, and a nonstationary propagation wave to fulfill the external loading requirement of shearography. The sweeping of the PZT excitation frequency, the formation of a standing wave, and a small shearing to suppress the incident wave were powerful controllable tools to detect the defects. The sweeping of the PZT excitation frequency enabled us to determine one of the defect-sensitive frequencies almost in real time. In addition, because the defect sensitive frequencies always existed in wide and plural ranges, the risk of the defect being overlooked by the inspector could be alleviated. The results of evaluation using stroboscopic shearography showed that an artificial 20 mm-diameter defect could be visualized at the excitation frequencies of 5-8 kHz range and 12.5-15.5 kHz range. This technique provided full field reliable and repeatable inspection results. Additionally, the proposed method overcame the important drawback of the time-averaged shearography, being required to identify the resonance vibration frequency sensitive to the defect.

  2. Skin cancer margin analysis within minutes with full-field OCT (Conference Presentation)

    Science.gov (United States)

    Dalimier, Eugénie; Ogrich, Lauren; Morales, Diego; Cusack, Carrie Ann; Abdelmalek, Mark; Boccara, Claude; Durkin, John

    2017-02-01

    Non-melanoma skin cancer (NMSC) is the most common cancer. Treatment consists of surgical removal of the skin cancer. Traditional excision involves the removal of the visible skin cancer with a significant margin of normal skin. On cosmetically sensitive areas, Mohs micrographic tissue is the standard of care. Mohs uses intraoperative microscopic margin assessment which minimizes the surgical defect and can help reduce the recurrence rate by a factor of 3. The current Mohs technique relies on frozen section tissue slide preparation which significantly lengthens operative time and requires on-site trained histotechnicians. Full-Field Optical Coherence Tomography (FFOCT) is a novel optical imaging technique which provides a quick and efficient method to visualize cancerous areas in minutes, without any preparation or destruction of the tissue. This study aimed to evaluate the potential of FFOCT for the analysis of skin cancer margins during Mohs surgery. Over 150 images of Mohs specimens were acquired intraoperatively with FFOCT before frozen section analysis. The imaging procedure took less than 5 minutes for each specimen. No artifacts on histological preparation were found arising from FFOCT manipulation; however frozen section artifact was readily seen on FFOCT. An atlas was established with FFOCT images and corresponding histological slides to reveal FFOCT reading criteria of normal and cancerous structures. Blind analysis showed high concordance between FFOCT and histology. FFOCT can potentially reduce recurrence rates while maintaining short surgery times, optimize clinical workflow, and decrease healthcare costs. For the patient, this translates into smaller infection risk, decreased stress, and better comfort.

  3. Breast Imaging Reporting and Data System (BI-RADS) breast composition descriptors: Automated measurement development for full field digital mammography

    OpenAIRE

    Fowler, E. E.; Sellers, T.A.; Lu, B.; Heine, J.J.

    2013-01-01

    Purpose: The Breast Imaging Reporting and Data System (BI-RADS) breast composition descriptors are used for standardized mammographic reporting and are assessed visually. This reporting is clinically relevant because breast composition can impact mammographic sensitivity and is a breast cancer risk factor. New techniques are presented and evaluated for generating automated BI-RADS breast composition descriptors using both raw and calibrated full field digital mammography (FFDM) image data.

  4. Estimation of surface curvature from full-field shape data using principal component analysis

    Science.gov (United States)

    Sharma, Sameer; Vinuchakravarthy, S.; Subramanian, S. J.

    2017-01-01

    Three-dimensional digital image correlation (3D-DIC) is a popular image-based experimental technique for estimating surface shape, displacements and strains of deforming objects. In this technique, a calibrated stereo rig is used to obtain and stereo-match pairs of images of the object of interest from which the shapes of the imaged surface are then computed using the calibration parameters of the rig. Displacements are obtained by performing an additional temporal correlation of the shapes obtained at various stages of deformation and strains by smoothing and numerically differentiating the displacement data. Since strains are of primary importance in solid mechanics, significant efforts have been put into computation of strains from the measured displacement fields; however, much less attention has been paid to date to computation of curvature from the measured 3D surfaces. In this work, we address this gap by proposing a new method of computing curvature from full-field shape measurements using principal component analysis (PCA) along the lines of a similar work recently proposed to measure strains (Grama and Subramanian 2014 Exp. Mech. 54 913-33). PCA is a multivariate analysis tool that is widely used to reveal relationships between a large number of variables, reduce dimensionality and achieve significant denoising. This technique is applied here to identify dominant principal components in the shape fields measured by 3D-DIC and these principal components are then differentiated systematically to obtain the first and second fundamental forms used in the curvature calculation. The proposed method is first verified using synthetically generated noisy surfaces and then validated experimentally on some real world objects with known ground-truth curvatures.

  5. Comparison of Photopic Negative Response of Full-Field and Focal Electroretinograms in Detecting Glaucomatous Eyes

    Directory of Open Access Journals (Sweden)

    Shigeki Machida

    2011-01-01

    Full Text Available Purpose. To compare the photopic negative response (PhNR of the full-field electroretinogram (ERG to the PhNR of the focal ERGs in detecting glaucoma. Methods. One hundred and three eyes with glaucoma and 42 normal eyes were studied. Full-field ERGs were elicited by red stimuli on a blue background. The focal ERGs were elicited by a 15∘ white stimulus spot centered on the macula, the superotemporal or the inferotemporal areas of the macula. Results. In early glaucoma, the areas under the receiver operating characteristic curves (AUCs were significantly larger for the focal PhNR (0.863–0.924 than those for the full-field PhNR (0.666–0.748 (P<.05. The sensitivity was significantly higher for the focal PhNR than for the full-field PhNR in early (P<.01 and intermediate glaucoma (P<.05. In advanced glaucoma, there was no difference in the AUCs and sensitivities between the focal and full-field PhNRs. Conclusions. The focal ERG has the diagnostic ability with higher sensitivity in detecting early and intermediate glaucoma than the full-field ERG.

  6. Comparison of Regression Techniques to Predict Response of Oilseed Rape Yield to Variation in Climatic Conditions in Denmark

    DEFF Research Database (Denmark)

    Sharif, Behzad; Makowski, David; Plauborg, Finn;

    2017-01-01

    -validation. The regression methods leading to the most accurate yield predictions were Lasso and Elastic Net, and the least accurate methods were ordinary least squares and stepwise regression. Partial least squares and ridge regression methods gave intermediate results. The estimated relative yield change for a +1°C......Statistical regression models represent alternatives to process-based dynamic models for predicting the response of crop yields to variation in climatic conditions. Regression models can be used to quantify the effect of change in temperature and precipitation on yields. However, it is difficult...... to identify the most relevant input variables that should be included in regression models due to the high number of candidate variables and to their correlations. This paper compares several regression techniques for modeling response of winter oilseed rape yield to a high number of correlated input...

  7. Full-field characterization of thermal diffusivity in continuous- fiber ceramic composite materials and components

    Energy Technology Data Exchange (ETDEWEB)

    Steckenrider, J.S.; Ellingson, W.A. [Argonne National Lab., IL (United States); Rothermel, S.A. [South Dakota State Univ., Brookings, SD (United States)

    1995-05-01

    Continuous-fiber ceramic matrix composites (CFCCs) are currently being developed for various high-temperature applications, including use in advanced heat engines. Among the material classes of interest for such applications are silicon carbide (SiC)-fiber-reinforced SiC (SiC{sub (f)}/SiC), SiC-fiber-reinforced silicon nitride (SiC {sub (f)}/Si{sub 3}N{sub 4}), aluminum oxide (Al{sub 2}O{sub 3})-fiber-reinforced Al{sub 2}O{sub 3} (Al{sub 2}O{sub 3}{sub (f)}/Al{sub 2}O{sub 3}), and others. In such composites, the condition of the interfaces (between the fibers and matrix) are critical to the mechanical and thermal behavior of the component (as are conventional mechanical defects such as cracks, porosity, etc.). For example, oxidation of this interface (especially on carbon coated fibers) can seriously degrade both mechanical and thermal properties. Furthermore, thermal shock damage can degrade the matrix through extensive crack generation. A nondestructive evaluation method that could be used to assess interface condition, thermal shock damage, and to detect other ``defects`` would thus be very beneficial, especially if applicable to full-scale components. One method under development uses infrared thermal imaging to provide ``single-shot`` full-field assessment of the distribution of thermal properties in large components by measuring thermal diffusivity. By applying digital image filtering, interpolation, and least-squares-estimation techniques for noise reduction, we can achieve acquisition and analysis times of minutes or less with submillimeter spatial resolution. The system developed at Argonne has been used to examine the effects of thermal shock, oxidation treatment, density variations, and variations in oxidation resistant coatings in a full array of test specimens. Subscale CFCC components with nonplanar geometries have also been studied for manufacturing-induced variations in thermal properties.

  8. Rapid evaluation of fresh ex vivo kidney tissue with full-field optical coherence tomography

    Directory of Open Access Journals (Sweden)

    Manu Jain

    2015-01-01

    Full Text Available Background: Full-field optical coherence tomography (FFOCT is a real-time imaging technique that rapidly generates images reminiscent of histology without any tissue processing, warranting its exploration for evaluation of ex vivo kidney tissue. Methods: Fresh tissue sections from tumor and adjacent nonneoplastic kidney (n = 25 nephrectomy specimens; clear cell renal cell carcinoma (CCRCC = 12, papillary RCC (PRCC = 4, chromophobe RCC (ChRCC = 4, papillary urothelial carcinoma (PUC = 1, angiomyolipoma (AML = 2 and cystic nephroma = 2 were imaged with a commercial FFOCT device. Sections were submitted for routine histopathological diagnosis. Results: Glomeruli, tubules, interstitium, and blood vessels were identified in nonneoplastic tissue. In tumor sections, the normal architecture was completely replaced by either sheets of cells/trabeculae or papillary structures. The former pattern was seen predominantly in CCRCC/ChRCC and the latter in PRCC/PUC (as confirmed on H&E. Although the cellular details were not very prominent at this resolution, we could identify unique cytoplasmic signatures in some kidney tumors. For example, the hyper-intense punctate signal in the cytoplasm of CRCC represents glycogen/lipid, large cells with abundant hyper-intense cytoplasm representing histiocytes in PRCC, and signal-void large polygonal cell representing adipocytes in AML. According to a blinded analysis was performed by an uropathologist, all nonneoplastic tissues were differentiated from neoplastic tissues. Further, all benign tumors were called benign and malignant were called malignant. A diagnostic accuracy of 80% was obtained in subtyping the tumors. Conclusion: The ability of FFOCT to reliably differentiate nonneoplastic from neoplastic tissue and identify some tumor types makes it a valuable tool for rapid evaluation of ex vivo kidney tissue e.g. for intraoperative margin assessment and kidney biopsy adequacy. Recently, higher resolution images were

  9. Quality control and primo-diagnosis of transurethral bladder resections with full-field OCT

    Science.gov (United States)

    Montagne, P.; Ducesne, I.; Anract, J.; Yang, C.; Sibony, M.; Beuvon, F.; Delongchamps, N. B.; Dalimier, E.

    2017-02-01

    Transurethral resections are commonly used for bladder cancer diagnosis, treatment and follow-up. Cancer staging relies largely on the analysis of muscle in the resections; however, muscle presence is uncertain at the time of the resection. An extemporaneous quality control tool would be of great use to certify the presence of muscle in the resection, and potentially formulate a primo-diagnosis, in order to ensure optimum patient care. Full-field optical coherence tomography (FFOCT) offers a fast and non-destructive method of obtaining images of biological tissues at ultrahigh resolution (1μm in all 3 directions), approaching traditional histological sections. This study aimed to evaluate the potential of FFOCT for the quality control and the primo-diagnosis of transurethral bladder resections. Over 70 transurethral bladder resections were imaged with FFOCT within minutes, shortly after excision, and before histological preparation. Side-by-side comparison with histology allowed to establish reading criteria for the presence of muscle and cancer in particular. Images of 24 specimens were read blindly by three non-pathologists readers: two resident urologists and a junior bio-medical engineer, who were asked to notify the presence of muscle and tumor. Results showed that after appropriate training, 96% accuracy could be obtained on both tumour and muscle detection. FFOCT is a fast and nondestructive imaging technique that provides analysis results concordant with histology. Its implementation as a quality control and primo-diagnosis tool for transurethral bladder resections in the urology suite is feasible and lets envision high value for the patient.

  10. Global sensitivity analysis in the identification of cohesive models using full-field kinematic data

    KAUST Repository

    Alfano, Marco

    2015-03-01

    Failure of adhesive bonded structures often occurs concurrent with the formation of a non-negligible fracture process zone in front of a macroscopic crack. For this reason, the analysis of damage and fracture is effectively carried out using the cohesive zone model (CZM). The crucial aspect of the CZM approach is the precise determination of the traction-separation relation. Yet it is usually determined empirically, by using calibration procedures combining experimental data, such as load-displacement or crack length data, with finite element simulation of fracture. Thanks to the recent progress in image processing, and the availability of low-cost CCD cameras, it is nowadays relatively easy to access surface displacements across the fracture process zone using for instance Digital Image Correlation (DIC). The rich information provided by correlation techniques prompted the development of versatile inverse parameter identification procedures combining finite element (FE) simulations and full field kinematic data. The focus of the present paper is to assess the effectiveness of these methods in the identification of cohesive zone models. In particular, the analysis is developed in the framework of the variance based global sensitivity analysis. The sensitivity of kinematic data to the sought cohesive properties is explored through the computation of the so-called Sobol sensitivity indexes. The results show that the global sensitivity analysis can help to ascertain the most influential cohesive parameters which need to be incorporated in the identification process. In addition, it is shown that suitable displacement sampling in time and space can lead to optimized measurements for identification purposes.

  11. Full-field optical coherence tomography for the analysis of fresh unstained human lobectomy specimens

    Directory of Open Access Journals (Sweden)

    Manu Jain

    2013-01-01

    Full Text Available Background: Full-field optical coherence tomography (FFOCT is a real-time imaging technique that generates high-resolution three-dimensional tomographic images from unprocessed and unstained tissues. Lack of tissue processing and associated artifacts, along with the ability to generate large-field images quickly, warrants its exploration as an alternative diagnostic tool. Materials and Methods: One section each from the tumor and from adjacent non-neoplastic tissue was collected from 13 human lobectomy specimens. They were imaged fresh with FFOCT and then submitted for routine histopathology. Two blinded pathologists independently rendered diagnoses based on FFOCT images. Results: Normal lung architecture (alveoli, bronchi, pleura and blood vessels was readily identified with FFOCT. Using FFOCT images alone, the study pathologists were able to correctly identify all tumor specimens and in many cases, the histological subtype of tumor (e.g., adenocarcinomas with various patterns. However, benign diagnosis was provided with high confidence in roughly half the tumor-free specimens (others were diagnosed as equivocal or false positive. Further analysis of these images revealed two major confounding features: (a Extensive lung collapse and (b presence of smoker′s macrophages. On a closer inspection, however, the smoker′s macrophages could often be identified as distinct from tumor cells based on their relative location in the alveoli, size and presence of anthracosis. We posit that greater pathologist experience, complemented with morphometric analysis and color-coding of image components, may help minimize the contribution of these confounders in the future. Conclusion: Our study provides evidence for the potential utility of FFOCT in identifying and differentiating lung tumors from non-neoplastic lung tissue. We foresee its potential as an adjunct to intra-surgical frozen section analysis for margin assessment, especially in limited lung

  12. Medical devices; radiology devices; reclassification of full-field digital mammography system. Final rule.

    Science.gov (United States)

    2010-11-05

    The Food and Drug Administration (FDA) is announcing the reclassification of the full-field digital mammography (FFDM) system from class III (premarket approval) to class II (special controls). The device type is intended to produce planar digital x-ray images of the entire breast; this generic type of device may include digital mammography acquisition software, full-field digital image receptor, acquisition workstation, automatic exposure control, image processing and reconstruction programs, patient and equipment supports, component parts, and accessories. The special control that will apply to the device is the guidance document entitled "Class II Special Controls Guidance Document: Full-Field Digital Mammography System." FDA is reclassifying the device into class II (special controls) because general controls along with special controls will provide a reasonable assurance of safety and effectiveness of the device. Elsewhere in this issue of the Federal Register, FDA is announcing the availability of the guidance document that will serve as the special control for this device.

  13. Composite NDE using full-field pulse-echo ultrasonic propagation imaging system

    Science.gov (United States)

    Hong, Seung-Chan; Lee, Jung-Ryul; Park, Jongwoon

    2016-04-01

    In this paper, a novel ultrasonic propagation imaging system, called a full-field pulse-echo ultrasonic propagation imaging (FF PE UPI) system is presented. The coincided laser beams for ultrasonic sensing and generation are scanned and pulse-echo mode laser ultrasounds are captured. This procedure makes it possible to generate full-field ultrasound in through-the-thickness direction as large as the scan area. The system nondestructively inspected targets with two-axis translation stages. Various structural inspection results in the form of full-field ultrasonic wave propagation videos are introduced, which are an aluminum honeycomb sandwich, ailerons and carbon fiber reinforced plastic (CFRP) honeycomb sandwich structures including various defects.

  14. Standardized Full-Field Electroretinography in the Green Monkey (Chlorocebus sabaeus)

    DEFF Research Database (Denmark)

    Bouskila, Joseph; Javadi, Pasha; Palmour, Roberta M

    2014-01-01

    Full-field electroretinography is an objective measure of retinal function, serving as an important diagnostic clinical tool in ophthalmology for evaluating the integrity of the retina. Given the similarity between the anatomy and physiology of the human and Green Monkey eyes, this species has......). Photopic and scotopic ERG recordings were obtained by full-field stimulation over a range of 6 log units of intensity in dark-adapted or light-adapted eyes of adult Green Monkeys (Chlorocebus sabaeus). Intensity, duration, and interval of light stimuli were varied separately. Reproducible values...

  15. Defect visualization of aircraft UHF antenna radome using full-field pulse-echo ultrasonic propagation imaging system

    Science.gov (United States)

    Shin, H. J.; Hong, S. C.; Lee, J. R.; Kim, J. H.

    2016-10-01

    Most of aircraft antennas usually have various types of radome made of composite materials for protecting antenna structures. However, these antenna radome structures, which are installed on the outside of airplane, are easy to be damaged by external forces such as drag, foreign object, bird strike and others. In this study, full-field pulse-echo ultrasonic propagation imaging (PE UPI) system is proposed as the non-destructive inspection technique to visualize manufacturing defects in composite antenna radome. Based on the results of the sample case study, it is shown that the ultrasonic wave propagation imaging (UWPI) that is generated by the proposed full-field PE UPI system is able to highlight the intact internal condition of antenna structure and its defect area. Additional damage visualization techniques like ultrasonic energy mapping (UEM), variable time window amplitude map (VTWAM) and also ultrasonic spectral imaging (USI) algorithms are applied to improve the reliability of the damage visualization. It can be concluded that the proposed PE UPI system is an effective non-destructive inspection technique for the composite radome structures.

  16. Combined full field stress and strain measurement methods for granular materials

    NARCIS (Netherlands)

    Dijkstra, J.; Broere, W.

    2010-01-01

    The current paper re-introduces the photoelastic measurement method in experimental geomechanics. A full-field phase stepping polariscope suitable for geomechanical model tests has been developed. Additional constraints on the measurement and mechanical setup arising from geomechanical test conditio

  17. High Yield Technique of Virus-free Potato Favorite Planting in Paddy

    Directory of Open Access Journals (Sweden)

    Yan-xia Zhang

    2013-04-01

    Full Text Available To screen the best combination cultivation factors, the orthogonal test was conducted on the 6 factors of virus-free potato Favorite including sowing time, density, urea, calcium superphosphate, potassium sulfate and zinc, planted in paddy field of Xian-ning, Luo-tian and Guang-shui. The results showed that: a experimental site had significant influence on growth period (F = 147.08>F0.01, sowing date had great significant influence on growth period (F = 15.68>F0.01, with the delay of sowing date, the growth period was short (R1 = 0.9851**. b Density had great significant influence on yield (F = 4.0>F0.01, the yield could be increased with the density increasing (R2 = 0.9782**, sowing date had significant influence on yield (F = 3.55>F0.05. c The maximum yield and economic return appeared at the treatment of seeding date December 10, seeding density 75000 plant/hm2, N 75 kg/hm2, phosphorus fertilizer 900 kg/hm2, potassium sulfate 450 kg/hm2 and zinc 22.5 kg/hm2, with the yield 31185 kg/hm2 and economic benefit 26833 Yuan/hm2.

  18. Full-field quantitative phase imaging by white-light interferometry with active phase stabilization and its application to biological samples

    Science.gov (United States)

    Li, Xinhong; Yamauchi, Toyohiko; Iwai, Hidenao; Yamashita, Yutaka; Zhang, Haijun; Hiruma, Teruo

    2006-06-01

    We report a Koehler-illumination-based full-field, actively stabilized, low-coherence phase-shifting interferometer, which is built on a white-light Michelson interferometer. By using a phase-stepping technique we can obtain full-field phase images of the sample. An actively stabilized phase-lock circuit is employed in the system to reduce phase noise. An application to human epithelial cells (HeLa cells) is achieved in our experiment. The advancement of this technique rests in its ability to take images of unstained biological samples quantitatively and on a nanometer scale.

  19. An analytic technique for the estimation of the light yield of a scintillation detector

    CERN Document Server

    Segreto, Ettore

    2011-01-01

    A simple model for the estimation of the light yield of a scintillation detector starting from the knowledge of its optical parameters and under general assumptions is developed. It is also shown how to take into account the effects related to Rayleigh scattering and absorption of the photons. The predictions of the model are benchmarked with the outcomes of a Monte Carlo simulation of a specific scintillation detector. The case of a real scintillation detector with internal surface covered by wavelength-shifter is explicitly treated and the model prediction is compared with the measured light yield.

  20. High-dynamic-range microscope imaging based on exposure bracketing in full-field optical coherence tomography.

    Science.gov (United States)

    Leong-Hoi, Audrey; Montgomery, Paul C; Serio, Bruno; Twardowski, Patrice; Uhring, Wilfried

    2016-04-01

    By applying the proposed high-dynamic-range (HDR) technique based on exposure bracketing, we demonstrate a meaningful reduction in the spatial noise in image frames acquired with a CCD camera so as to improve the fringe contrast in full-field optical coherence tomography (FF-OCT). This new signal processing method thus allows improved probing within transparent or semitransparent samples. The proposed method is demonstrated on 3 μm thick transparent polymer films of Mylar, which, due to their transparency, produce low contrast fringe patterns in white-light interference microscopy. High-resolution tomographic analysis is performed using the technique. After performing appropriate signal processing, resulting XZ sections are observed. Submicrometer-sized defects can be lost in the noise that is present in the CCD images. With the proposed method, we show that by increasing the signal-to-noise ratio of the images, submicrometer-sized defect structures can thus be detected.

  1. Full-field modal analysis during base motion excitation using high-speed 3D digital image correlation

    Science.gov (United States)

    Molina-Viedma, Ángel J.; López-Alba, Elías; Felipe-Sesé, Luis; Díaz, Francisco A.

    2017-10-01

    In recent years, many efforts have been made to exploit full-field measurement optical techniques for modal identification. Three-dimensional digital image correlation using high-speed cameras has been extensively employed for this purpose. Modal identification algorithms are applied to process the frequency response functions (FRF), which relate the displacement response of the structure to the excitation force. However, one of the most common tests for modal analysis involves the base motion excitation of a structural element instead of force excitation. In this case, the relationship between response and excitation is typically based on displacements, which are known as transmissibility functions. In this study, a methodology for experimental modal analysis using high-speed 3D digital image correlation and base motion excitation tests is proposed. In particular, a cantilever beam was excited from its base with a random signal, using a clamped edge join. Full-field transmissibility functions were obtained through the beam and converted into FRF for proper identification, considering a single degree-of-freedom theoretical conversion. Subsequently, modal identification was performed using a circle-fit approach. The proposed methodology facilitates the management of the typically large amounts of data points involved in the DIC measurement during modal identification. Moreover, it was possible to determine the natural frequencies, damping ratios and full-field mode shapes without requiring any additional tests. Finally, the results were experimentally validated by comparing them with those obtained by employing traditional accelerometers, analytical models and finite element method analyses. The comparison was performed by using the quantitative indicator modal assurance criterion. The results showed a high level of correspondence, consolidating the proposed experimental methodology.

  2. Standardized full-field electroretinography in the Green Monkey (Chlorocebus sabaeus.

    Directory of Open Access Journals (Sweden)

    Joseph Bouskila

    Full Text Available Full-field electroretinography is an objective measure of retinal function, serving as an important diagnostic clinical tool in ophthalmology for evaluating the integrity of the retina. Given the similarity between the anatomy and physiology of the human and Green Monkey eyes, this species has increasingly become a favorable non-human primate model for assessing ocular defects in humans. To test this model, we obtained full-field electroretinographic recordings (ERG and normal values for standard responses required by the International Society for Clinical Electrophysiology of Vision (ISCEV. Photopic and scotopic ERG recordings were obtained by full-field stimulation over a range of 6 log units of intensity in dark-adapted or light-adapted eyes of adult Green Monkeys (Chlorocebus sabaeus. Intensity, duration, and interval of light stimuli were varied separately. Reproducible values of amplitude and latency were obtained for the a- and b-waves, under well-controlled adaptation and stimulus conditions; the i-wave was also easily identifiable and separated from the a-b-wave complex in the photopic ERG. The recordings obtained in the healthy Green Monkey matched very well with those in humans and other non-human primate species (Macaca mulatta and Macaca fascicularis. These results validate the Green Monkey as an excellent non-human primate model, with potential to serve for testing retinal function following various manipulations such as visual deprivation or drug evaluation.

  3. Using Geostatistical Data Fusion Techniques and MODIS Data to Upscale Simulated Wheat Yield

    Science.gov (United States)

    Castrignano, A.; Buttafuoco, G.; Matese, A.; Toscano, P.

    2014-12-01

    Population growth increases food request. Assessing food demand and predicting the actual supply for a given location are critical components of strategic food security planning at regional scale. Crop yield can be simulated using crop models because is site-specific and determined by weather, management, length of growing season and soil properties. Crop models require reliable location-specific data that are not generally available. Obtaining these data at a large number of locations is time-consuming, costly and sometimes simply not feasible. An upscaling method to extend coverage of sparse estimates of crop yield to an appropriate extrapolation domain is required. This work is aimed to investigate the applicability of a geostatistical data fusion approach for merging remote sensing data with the predictions of a simulation model of wheat growth and production using ground-based data. The study area is Capitanata plain (4000 km2) located in Apulia Region, mostly cropped with durum wheat. The MODIS EVI/NDVI data products for Capitanata plain were downloaded from the Land Processes Distributed Active Archive Center (LPDAAC) remote for the whole crop cycle of durum wheat. Phenological development, biomass growth and grain quantity of durum wheat were simulated by the Delphi system, based on a crop simulation model linked to a database including soil properties, agronomical and meteorological data. Multicollocated cokriging was used to integrate secondary exhaustive information (multi-spectral MODIS data) with primary variable (sparsely distributed biomass/yield model predictions of durum wheat). The model estimates looked strongly spatially correlated with the radiance data (red and NIR bands) and the fusion data approach proved to be quite suitable and flexible to integrate data of different type and support.

  4. Behaviour model identification based on inverse modeling and using Optical Full Field Measurements (OFFM): application on rubber and steel

    Science.gov (United States)

    Velay, V.; Robert, L.; Schmidt, F.; Hmida, S.; Vallet, T.

    2007-04-01

    Biaxial properties of materials (polymer or steel) used in many industrial processes are often difficult to measure. However, these properties are useful for the numerical simulations of plastic-processing operations like blow moulding or thermoforming for polymers and superplastic forming or single point incremental forming for steels. Today, Optical Full Field Measurements (OFFM) are promising tools for experimental analysis of materials. Indeed, they are able to provide a very large amount of data (displacement or strain) spatially distributed. In this paper, a mixed numerical and experimental investigation is proposed in order to identify multi-axial constitutive behaviour models. The procedure is applied on two different materials commonly used in forming processes: polymer (rubber in this first approach) and steel. Experimental tests are performed on various rubber and steel structural specimens (notched and open-hole plate samples) in order to generate heterogeneous displacement field. Two different behaviour models are considered. On the one hand, a Money-Rivlin hyperelastic law is investigated to describe the high levels of strain induced in tensile test performed on a rubber open-hole specimen. On the other hand, Ramberg-Osgood law allows to reproduce elasto-plastic behaviour of steel on a specimen that induces heterogeneous strain fields. Each parameter identification is based on a same Finite Element Model Updated (FEMU) procedure which consists in comparing results provided by the numerical simulation (ABAQUS™) with full field measurements obtained by the DISC (Digital Image Stereo-Correlation) technique (Vic-3D®).

  5. High process yield rates of thermoplastic nanofluidic devices using a hybrid thermal assembly technique.

    Science.gov (United States)

    Uba, Franklin I; Hu, Bo; Weerakoon-Ratnayake, Kumuditha; Oliver-Calixte, Nyote; Soper, Steven A

    2015-02-21

    Over the past decade, thermoplastics have been used as alternative substrates to glass and Si for microfluidic devices because of the diverse and robust fabrication protocols available for thermoplastics that can generate high production rates of the desired structures at low cost and with high replication fidelity, the extensive array of physiochemical properties they possess, and the simple surface activation strategies that can be employed to tune their surface chemistry appropriate for the intended application. While the advantages of polymer microfluidics are currently being realized, the evolution of thermoplastic-based nanofluidic devices is fraught with challenges. One challenge is assembly of the device, which consists of sealing a cover plate to the patterned fluidic substrate. Typically, channel collapse or substrate dissolution occurs during assembly making the device inoperable resulting in low process yield rates. In this work, we report a low temperature hybrid assembly approach for the generation of functional thermoplastic nanofluidic devices with high process yield rates (>90%) and with a short total assembly time (16 min). The approach involves thermally sealing a high T(g) (glass transition temperature) substrate containing the nanofluidic structures to a cover plate possessing a lower T(g). Nanofluidic devices with critical feature sizes ranging between 25-250 nm were fabricated in a thermoplastic substrate (T(g) = 104 °C) and sealed with a cover plate (T(g) = 75 °C) at a temperature significantly below the T(g) of the substrate. Results obtained from sealing tests revealed that the integrity of the nanochannels remained intact after assembly and devices were useful for fluorescence imaging at high signal-to-noise ratios. The functionality of the assembled devices was demonstrated by studying the stretching and translocation dynamics of dsDNA in the enclosed thermoplastic nanofluidic channels.

  6. 3D Imaging of Nickel Oxidation States using Full Field X-ray Absorption Near Edge Structure Nanotomography

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, George; Harris, William; Izzo, John; Grew, Kyle N. (Connecticut); (USARL)

    2012-01-20

    Reduction-oxidation (redox) cycling of the nickel electrocatalyst phase in the solid oxide fuel cell (SOFC) anode can lead to performance degradation and cell failure. A greater understanding of nickel redox mechanisms at the microstructural level is vital to future SOFC development. Transmission x-ray microscopy (TXM) provides several key techniques for exploring oxidation states within SOFC electrode microstructure. Specifically, x-ray nanotomography and x-ray absorption near edge structure (XANES) spectroscopy have been applied to study samples of varying nickel (Ni) and nickel oxide (NiO) compositions. The imaged samples are treated as mock SOFC anodes containing distinct regions of the materials in question. XANES spectra presented for the individual materials provide a basis for the further processing and analysis of mixed samples. Images of composite samples obtained are segmented, and the distinct nickel and nickel oxide phases are uniquely identified using full field XANES spectroscopy. Applications to SOFC analysis are discussed.

  7. En-face full-field optical coherence tomography for fast and efficient fingerprints acquisition

    Science.gov (United States)

    Harms, Fabrice; Dalimier, Eugénie; Boccara, A. Claude

    2014-05-01

    Optical coherence tomography (OCT) has been recently proposed by a number of laboratories as a promising tool for fingerprints acquisitions and for fakes discrimination. Indeed OCT being a non-contact, non-destructive optical method that virtually sections the volume of biological tissues that strongly scatter light it appears obvious to use it for fingerprints. Nevertheless most of the OCT setups have to go through the long acquisition of a full 3D image to isolate an "en-face" image suitable for fingerprint analysis. A few "en-face" OCT approaches have been proposed that use either a complex 2D scanning setup and image processing, or a full-field illumination using a camera and a spatially coherent source that induces crosstalks and degrades the image quality. We show here that Full Field OCT (FFOCT) using a spatially incoherent source is able to provide "en-face" high quality optical sectioning of the fingers skin. Indeed such approach shows a unique spatial resolution able to reveal a number of morphological details of fingerprints that are not seen with competing OCT setups. In particular the cellular structure of the stratum corneum and the epidermis-dermis interface appear clearly. We describe our high-resolution (1 micrometer, isotropic) setup and show our first design to get a large field of view while keeping a good sectioning ability of about 3 micrometers. We display the results obtained using these two setups for fingerprints examination.

  8. Homodyne full-field interferometer for measuring dynamic surface phenomena in microstructures

    Science.gov (United States)

    Lipiäinen, Lauri; Kokkonen, Kimmo; Kaivola, Matti

    2017-01-01

    We describe a stabilized homodyne full-field interferometer capable of measuring vertical surface deformations of microstructures in the time domain. The interferometer is stabilized to a chosen operation point by obtaining a feedback signal from a non-moving, freely selectable, reference region on the sample surface. The stabilized full-field interferometer enables detection of time-dependent changes in the surface profile with nanometer scale vertical resolution, while the temporal resolution of the measurement is ultimately limited by the refresh rate of the camera only. The lateral resolution of the surface deformation is determined by the combination of the imaging optics together with the pixel size of the camera. The setup is used to measure the deformation of an Aluminum nitride membrane as a function of time-dependent pressure change. The data analysis allows for unambiguous determination of surface deformations over multiple fringes of the interferogram, hence enabling the study of a wide range of physical phenomena with varying magnitude of vertical surface movement.

  9. [Full-field and automatic methodology of spectral calibration for PGP imaging spectrometer].

    Science.gov (United States)

    Sun, Ci; Bayanheshig; Cui, Ji-cheng; Pan, Ming-zhong; Li, Xiao-tian; Tang, Yu-guo

    2014-08-01

    In order to analyze spectral data quantitatively which is obtained by prism-grating-prism imaging spectrometer, spectral calibration is required in order to determine spectral characteristics of PGP imaging spectrometer, such as the center wavelength of every spectral channel, spectral resolution and spectral bending. A spectral calibration system of full field based on collimated monochromatic light method is designed. Spherical mirror is used to provide collimated light, and a freely sliding and rotating folding mirror is adopted to change the angle of incident light in order to realize full field and automatic calibration of imaging spectrometer. Experiments of spectral calibration have been done for PGP imaging spectrometer to obtain parameters of spectral performance, and accuracy analysis combined with the structural features of the entire spectral calibration system have been done. Analysis results indicate that spectral calibration accuracy of the calibration system reaches 0.1 nm, and the bandwidth accuracy reaches 1.3%. The calibration system has merits of small size, better commonality, high precision and so on, and because of adopting the control of automation, the additional errors which are caused by human are avoided. The calibration system can be used for spectral calibration of other imaging spectrometers whose structures are similar to PGP.

  10. Rat brain imaging using full field optical coherence microscopy with short multimode fiber probe

    Science.gov (United States)

    Sato, Manabu; Saito, Daisuke; Kurotani, Reiko; Abe, Hiroyuki; Kawauchi, Satoko; Sato, Shunichi; Nishidate, Izumi

    2017-02-01

    We demonstrated FF OCM(full field optical coherence microscopy) using an ultrathin forward-imaging SMMF (short multimode fiber) probe of 50 μm core diameter, 125 μm diameter, and 7.4 mm length, which is a typical graded-index multimode fiber for optical communications. The axial resolution was measured to be 2.20 μm, which is close to the calculated axial resolution of 2.06 μm. The lateral resolution was evaluated to be 4.38 μm using a test pattern. Assuming that the FWHM of the contrast is the DOF (depth of focus), the DOF of the signal is obtained at 36 μm and that of the OCM is 66 μm. The contrast of the OCT images was 6.1 times higher than that of the signal images due to the coherence gate. After an euthanasia the rat brain was resected and cut at 2.6mm tail from Bregma. Contacting SMMF to the primary somatosensory cortex and the agranular insular cortex of ex vivo brain, OCM images of the brain were measured 100 times with 2μm step. 3D OCM images of the brain were measured, and internal structure information was obtained. The feasibility of an SMMF as an ultrathin forward-imaging probe in full-field OCM has been demonstrated.

  11. Monitoring bolt torque levels through signal processing of full-field ultrasonic data

    Science.gov (United States)

    Haynes, Colin; Yeager, Michael; Todd, Michael; Lee, Jung-Ryul

    2014-03-01

    Using full-field ultrasonic guided wave data can provide a wealth of information on the state of a structure through a detailed characterization of its wave propagation properties. However, the need for appropriate feature selection and quantified metrics for making rigorous assessments of the structural state is in no way lessened by the density of information. In this study, a simple steel bolted connection with two bolts is monitored for bolt loosening. The full-field data were acquired using a scanning-laser-generated ultrasound system with a single surface-mounted sensor. Such laser systems have many advantages that make them attractive for nondestructive evaluation, including their high-speed, high spatial resolution, and the ability to scan large areas of in-service structures. In order to characterize the relationship between bolt torque and the resulting wavefield in this specimen, the bolt torque in each of the bolts is independently varied from fully tightened to fully loosened in several steps. First, qualitative observations about the changes in the wavefield are presented. Next, an approach to quantifying the wave transmission through the bolted joint is discussed. Finally, a method of monitoring the bolt torque using the ultrasonic data is demonstrated.

  12. Robust full-field measurement considering rotation using digital image correlation

    Science.gov (United States)

    Wu, Rong; Qian, Hao; Zhang, Dongsheng

    2016-10-01

    Digital image correlation (DIC) has been widely accepted as a method for displacement and strain measurement and is applied in a variety of engineering fields. Most DIC algorithms encounter errors in measuring the deformation in conditions that involve rotation since they are designed without considering rotation of the deformed object. In this paper, a robust and automated DIC method capable of determining full-field displacement and strain components with random rotations has been presented. The algorithm starts with the determination of the initial position of the seed point in the integer-pixel domain. An approximate rotational angle between the reference and the deformed subset is estimated using an automated feature matching technology. A two-step Newton-Raphson algorithm has been developed for optimizing a suite of variables including displacement, strain and the rotational angle to achieve subpixel accuracy. A reliable propagation scheme, which enables rapid determination of the initial guess for full-field analysis is also proposed. Results from numerical simulations are used to validate the feasibility of the proposed DIC method. An application to 3-point bending with large deflection shows that the algorithm can be employed to measure displacement or strain parameters of the deformed object with arbitrary angles of rotation.

  13. High-Bandwidth Dynamic Full-Field Profilometry for Nano-Scale Characterization of MEMS

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L-C [Graduate Institute of Automation Technology, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China); Huang, Y-T [Graduate Institute of Automation Technology, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China); Chang, P-B [Graduate Institute of Mechanical and Electrical Engineering, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China)

    2006-10-15

    The article describes an innovative optical interferometric methodology to delivery dynamic surface profilometry with a measurement bandwidth up to 10MHz or higher and a vertical resolution up to 1 nm. Previous work using stroboscopic microscopic interferometry for dynamic characterization of micro (opto)electromechanical systems (M(O)EMS) has been limited in measurement bandwidth mainly within a couple of MHz. For high resonant mode analysis, the stroboscopic light pulse is insufficiently short to capture the moving fringes from dynamic motion of the detected structure. In view of this need, a microscopic prototype based on white-light stroboscopic interferometry with an innovative light superposition strategy was developed to achieve dynamic full-field profilometry with a high measurement bandwidth up to 10MHz or higher. The system primarily consists of an optical microscope, on which a Mirau interferometric objective embedded with a piezoelectric vertical translator, a high-power LED light module with dual operation modes and light synchronizing electronics unit are integrated. A micro cantilever beam used in AFM was measured to verify the system capability in accurate characterisation of dynamic behaviours of the device. The full-field seventh-mode vibration at a vibratory frequency of 3.7MHz can be fully characterized and nano-scale vertical measurement resolution as well as tens micrometers of vertical measurement range can be performed.

  14. Digital image correlation for full-field time-resolved assessment of arterial stiffness

    Science.gov (United States)

    Campo, Adriaan; Soons, Joris; Heuten, Hilde; Ennekens, Guy; Goovaerts, Inge; Vrints, Christiaan; Lava, Pascal; Dirckx, Joris

    2014-01-01

    Pulse wave velocity (PWV) of the arterial system is a very important parameter to evaluate cardiovascular health. Currently, however, there is no golden standard for PWV measurement. Digital image correlation (DIC) was used for full-field time-resolved assessment of displacement, velocity, acceleration, and strains of the skin in the neck directly above the common carotid artery. By assessing these parameters, propagation of the pulse wave could be tracked, leading to a new method for PWV detection based on DIC. The method was tested on five healthy subjects. As a means of validation, PWV was measured with ultrasound (US) as well. Measured PWV values were between 3.68 and 5.19 m/s as measured with DIC and between 5.14 and 6.58 m/s as measured with US, with a maximum absolute difference of 2.78 m/s between the two methods. DIC measurements of the neck region can serve as a test base for determining a robust strategy for PWV detection, they can serve as reference for three-dimensional fluid-structure interaction models, or they may even evolve into a screening method of their own. Moreover, full-field, time-resolved DIC can be adapted for other applications in biomechanics.

  15. Reconstructing material properties by deconvolution of full-field measurement images: The conductivity case

    Science.gov (United States)

    Bellis, Cédric; Trabelsi, Manel; Frémy, Flavien

    2017-03-01

    This study concerns the reconstruction of material parameters from full-field measurements. In this context the typical available data is a set of digital images that is seldom handled as such when solving the inverse problem. Therefore, this work investigates a direct method to compute constitutive parameter maps from full-field measurement images. Within the prototypical framework of the periodic conductivity model, the starting point for the proposed approach is the Lippmann-Schwinger equation, which is satisfied by the fields measured internally. This integral equation is reinterpreted as a linear convolution model for the sought conductivity field. Considering that multiple experiments might be available and then combined, this problem is solved in the least-square sense. To do so, the Krylov subspace-based LSQR algorithm is employed. Full advantage is taken of the convenient expression of the featured Green’s function in Fourier space and of the intensive use of the fast Fourier transform (FFT). Moreover, a spectral-based filtering regularization scheme is implemented to tackle noisy data. Overall, the proposed reconstruction algorithm only handles image-like quantities in an efficient mesh-free approach. The performance of the method is assessed on a set of synthetic 2D numerical examples both for isotropic and anisotropic material configurations.

  16. Measurements of fusion neutron yields by neutron activation technique: Uncertainty due to the uncertainty on activation cross-sections

    Energy Technology Data Exchange (ETDEWEB)

    Stankunas, Gediminas, E-mail: gediminas.stankunas@lei.lt [Lithuanian Energy Institute, Laboratory of Nuclear Installation Safety, Breslaujos str. 3, LT-44403 Kaunas (Lithuania); EUROfusion Consortium, JET, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Batistoni, Paola [ENEA, Via E. Fermi, 45, 00044 Frascati, Rome (Italy); EUROfusion Consortium, JET, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Sjöstrand, Henrik; Conroy, Sean [Department of Physics and Astronomy, Uppsala University, PO Box 516, SE-75120 Uppsala (Sweden); EUROfusion Consortium, JET, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)

    2015-07-11

    The neutron activation technique is routinely used in fusion experiments to measure the neutron yields. This paper investigates the uncertainty on these measurements as due to the uncertainties on dosimetry and activation reactions. For this purpose, activation cross-sections were taken from the International Reactor Dosimetry and Fusion File (IRDFF-v1.05) in 640 groups ENDF-6 format for several reactions of interest for both 2.5 and 14 MeV neutrons. Activation coefficients (reaction rates) have been calculated using the neutron flux spectra at JET vacuum vessel, both for DD and DT plasmas, calculated by MCNP in the required 640-energy group format. The related uncertainties for the JET neutron spectra are evaluated as well using the covariance data available in the library. These uncertainties are in general small, but not negligible when high accuracy is required in the determination of the fusion neutron yields.

  17. Classification and analysis of human ovarian tissue using full field optical coherence tomography.

    Science.gov (United States)

    Nandy, Sreyankar; Sanders, Melinda; Zhu, Quing

    2016-12-01

    In this study, a full field optical coherence tomography (FFOCT) system was used to analyze and classify normal and malignant human ovarian tissue. 14 ovarian tissue samples (7 normal, 7 malignant) were imaged with the FFOCT system and five features were extracted by analyzing the normalized image histogram from 56 FFOCT images, based on the differences in the morphology of the normal and malignant tissue samples. A generalized linear model (GLM) classifier was trained using 36 images, and sensitivity of 95.3% and specificity of 91.1% was obtained. 20 images were used to test the model, and a sensitivity of 91.6% and specificity of 87.7% was obtained.

  18. Applications of Hard X-ray Full-Field Transmission X-ray Microscopy at SSRL

    Science.gov (United States)

    Liu, Y.; Andrews, J. C.; Meirer, F.; Mehta, A.; Gil, S. Carrasco; Sciau, P.; Mester, Z.; Pianetta, P.

    2011-09-01

    State-of-the-art hard x-ray full-field transmission x-ray microscopy (TXM) at beamline 6-2C of Stanford Synchrotron Radiation Lightsource has been applied to various research fields including biological, environmental, and material studies. With the capability of imaging a 32-micron field-of-view at 30-nm resolution using both absorption mode and Zernike phase contrast, the 3D morphology of yeast cells grown in gold-rich media was investigated. Quantitative evaluation of the absorption coefficient was performed for mercury nanoparticles in alfalfa roots exposed to mercury. Combining XANES and TXM, we also performed XANES-imaging on an ancient pottery sample from the Roman pottery workshop at LaGraufesenque (Aveyron).

  19. A high-speed full-field profilometry with coded laser strips projection

    Science.gov (United States)

    Zhang, Guanliang; Zhou, Xiang; Jin, Rui; Xu, Changda; Li, Dong

    2017-06-01

    Line structure light measurement needs accurate mechanical movement device and high -frame-rate camera, which is difficult to realize. We propose a high-speed full-field profilometry to solve these difficult ies, using coded laser strips projected by a MEMS scanning mirror. The mirror could take place of the mechanical movement device with its high speed and accurate. Besides, a method with gray code and color code is used to decrease the frames number of projection, retaining the advantage of line structure light measurement. In the experiment, we use a laser MEMS scanner and two color cameras. The laser MEMS scanner projects coded stripes, with two color cameras collecting the modulated pattern on the measured object. The color cameras compose a stereo vision system so that the three-dimensional data is reconstructed according to triangulation.

  20. Full-field implementation of a perfect eavesdropper on a quantum cryptography system.

    Science.gov (United States)

    Gerhardt, Ilja; Liu, Qin; Lamas-Linares, Antía; Skaar, Johannes; Kurtsiefer, Christian; Makarov, Vadim

    2011-06-14

    Quantum key distribution (QKD) allows two remote parties to grow a shared secret key. Its security is founded on the principles of quantum mechanics, but in reality it significantly relies on the physical implementation. Technological imperfections of QKD systems have been previously explored, but no attack on an established QKD connection has been realized so far. Here we show the first full-field implementation of a complete attack on a running QKD connection. An installed eavesdropper obtains the entire 'secret' key, while none of the parameters monitored by the legitimate parties indicate a security breach. This confirms that non-idealities in physical implementations of QKD can be fully practically exploitable, and must be given increased scrutiny if quantum cryptography is to become highly secure.

  1. Study of Wood Plastic Composites elastic behaviour using full field measurements

    Science.gov (United States)

    Ben Mbarek, T.; Robert, L.; Hugot, F.; Orteu, J. J.; Sammouda, H.; Graciaa, A.; Charrier, B.

    2010-06-01

    In this study, the mechanical properties and microstructure of HDPE/wood fibre composites are investigated. The four-point bending and tensile behaviour of Wood Plastic Composite (WPC) with or without additive are studied by using full-field strain measurements by 3-D Digital Image Correlation (3-D DIC). A non-linear behaviour is shown. The modulus of elasticity (MOE) is calculated as the tangent at zero strain of a Maxwell-Bingham model fitted onto experimental data. Four-point bending tests are analyzed thanks to the spatial standard deviation of the longitudinal strain field to determine the degree of heterogeneity. Cyclic tensile tests have been performed in order to analyze the damage of the material. Moreover, Scanning Electron Microscope (SEM) is used to characterize the morphology of the wood fibre/HDPE matrix interface for specimens with maleic anhydride modified polyethylene additive (MAPE).

  2. Study of Wood Plastic Composites elastic behaviour using full field measurements

    Directory of Open Access Journals (Sweden)

    Graciaa A.

    2010-06-01

    Full Text Available In this study, the mechanical properties and microstructure of HDPE/wood fibre composites are investigated. The four-point bending and tensile behaviour of Wood Plastic Composite (WPC with or without additive are studied by using full-field strain measurements by 3-D Digital Image Correlation (3-D DIC. A non-linear behaviour is shown. The modulus of elasticity (MOE is calculated as the tangent at zero strain of a Maxwell-Bingham model fitted onto experimental data. Four-point bending tests are analyzed thanks to the spatial standard deviation of the longitudinal strain field to determine the degree of heterogeneity. Cyclic tensile tests have been performed in order to analyze the damage of the material. Moreover, Scanning Electron Microscope (SEM is used to characterize the morphology of the wood fibre/HDPE matrix interface for specimens with maleic anhydride modified polyethylene additive (MAPE.

  3. Full-field laser Doppler imaging and its physiological significance for tissue blood perfusion

    Science.gov (United States)

    Binzoni, T.; Van DeVille, D.

    2008-12-01

    Using Monte Carlo simulations for a semi-infinite medium representing a skeletal muscle tissue, it is demonstrated that the zero- and first-order moments of the power spectrum for a representative pixel of a full-field laser-Doppler imager behave differently from classical laser-Doppler flowmetry. In particular, the zero-order moment has a very low sensitivity to tissue blood volume changes, and it becomes completely insensitive if the probability for a photon to interact with a moving red blood cell is above 0.05. It is shown that the loss in sensitivity is due to the strong forward scatter of the propagating photons in biological tissues (i.e., anisotropy factor g = 0.9). The first-order moment is linearly related to the root mean square of the red blood cell velocity (the Brownian component), and there is also a positive relationship with tissue blood volume. The most common physiological interpretation of the first-order moment is as tissue blood volume times expectation of the blood velocity (in probabilistic terms). In this sense, the use of the first-order moment appears to be a reasonable approach for qualitative real-time blood flow monitoring, but it does not allow us to obtain information on blood velocity or volume independently. Finally, it is shown that the spatial and temporal resolution trade-off imposed by the CMOS detectors, used in full-field laser-Doppler hardware, may lead to measurements that vary oppositely with the underlying physiological quantities. Further improvements on detectors' sampling rate will overcome this limitation.

  4. Full-field laser-Doppler imaging and its physiological significance for tissue blood perfusion

    Energy Technology Data Exchange (ETDEWEB)

    Binzoni, T [Departement des Neurosciences Fondamentales, University of Geneva (Switzerland); Ville, D van de [Biomedical Imaging Group, Ecole Polytechnique Federale de Lausanne (EPFL) (Switzerland)], E-mail: Tiziano.Binzoni@medecine.unige.ch

    2008-12-07

    Using Monte Carlo simulations for a semi-infinite medium representing a skeletal muscle tissue, it is demonstrated that the zero- and first-order moments of the power spectrum for a representative pixel of a full-field laser-Doppler imager behave differently from classical laser-Doppler flowmetry. In particular, the zero-order moment has a very low sensitivity to tissue blood volume changes, and it becomes completely insensitive if the probability for a photon to interact with a moving red blood cell is above 0.05. It is shown that the loss in sensitivity is due to the strong forward scatter of the propagating photons in biological tissues (i.e., anisotropy factor g = 0.9). The first-order moment is linearly related to the root mean square of the red blood cell velocity (the Brownian component), and there is also a positive relationship with tissue blood volume. The most common physiological interpretation of the first-order moment is as tissue blood volume times expectation of the blood velocity (in probabilistic terms). In this sense, the use of the first-order moment appears to be a reasonable approach for qualitative real-time blood flow monitoring, but it does not allow us to obtain information on blood velocity or volume independently. Finally, it is shown that the spatial and temporal resolution trade-off imposed by the CMOS detectors, used in full-field laser-Doppler hardware, may lead to measurements that vary oppositely with the underlying physiological quantities. Further improvements on detectors' sampling rate will overcome this limitation.

  5. High-resolution imaging of biological tissue with full-field optical coherence tomography

    Science.gov (United States)

    Zhu, Yue; Gao, Wanrong

    2015-03-01

    A new full-field optical coherence tomography system with high-resolution has been developed for imaging of cells and tissues. Compared with other FF-OCT (Full-field optical coherence tomography, FF-OCT) systems illuminated with optical fiber bundle, the improved Köhler illumination arrangement with a halogen lamp was used in the proposed FF-OCT system. High numerical aperture microscopic objectives were used for imaging and a piezoelectric ceramic transducer (PZT) was used for phase-shifting. En-face tomographic images can be obtained by applying the five-step phase-shifting algorithm to a series of interferometric images which are recorded by a smart camera. Three-dimensional images can be generated from these tomographic images. Imaging of the chip of Intel Pentium 4 processor demonstrated the ultrahigh resolution of the system (lateral resolution is 0.8μm ), which approaches the theoretical resolution 0.7 μm× 0.5 μm (lateral × axial). En-face images of cells of onion show an excellent performance of the system in generating en-face images of biological tissues. Then, unstained pig stomach was imaged as a tissue and gastric pits could be easily recognized using FF-OCT system. Our study provides evidence for the potential ability of FFOCT in identifying gastric pits from pig stomach tissue. Finally, label-free and unstained ex vivo human liver tissues from both normal and tumor were imaged with this FFOCT system. The results show that the setup has the potential for medical diagnosis applications such liver cancer diagnosis.

  6. Optical biopsy on head and neck tissue using full-field OCT: a pilot study

    Science.gov (United States)

    De Leeuw, Frédéric; Latrive, Anne; Casiraghi, Odile; Ferchiou, Malek; Harms, Fabrice; Boccara, Claude; Laplace-Builhé, Corinne

    2014-03-01

    Here we evaluate the clinical value of Full-Field OCT imaging in the management of patients with Head and Neck cancers by making a reliable histological diagnosis on FFOCT images produced during preoperative procedure. FFOCT performs a true "virtual extemporaneous exam" that we want to compare to the gold standard (extemporaneous and conventional histology with H and E staining). This new optical technology could be useful when diagnosing a lesion, cancerous or precancerous, or at the time of its surgical management. Full-Field Optical Coherence Tomography virtually slices the tissue using white light interferometry to produce in-depth 2D images with an isotropic resolution around 1 micrometer. With such a high resolution FFOCT systems produce "optical biopsy" images that are similar to that obtained with classical histology procedures, but without any staining and in only a few minutes. We imaged freshly excised samples from patients, of mouth, tongue, epiglottis and larynx tissues, both healthy and cancerous. FFOCT images were acquired and later compared with histology of the same samples. Common features were identified and characteristics of each tissue type were matched in order to form an image atlas for pathologist training. We were able to identify indicators of tumors such as heterogeneities in cell distribution, surrounding stroma, anomalous keratinization… In conclusion, FFOCT is a fast, non-invasive, non-destructive imaging tool that can be inserted into the pathology lab workflow and can provide a quick assessment of microscopic tissue architecture and content. Furthermore we are developing a similar system with a rigid endoscopic probe in order to do in vivo and in situ high-resolution imaging. Our probe could thus guide the surgeon in real time before and during excision and ensure a more precise gesture.

  7. Calibration of aero-structural reduced order models using full-field experimental measurements

    Science.gov (United States)

    Perez, R.; Bartram, G.; Beberniss, T.; Wiebe, R.; Spottswood, S. M.

    2017-03-01

    The structural response of hypersonic aircraft panels is a multi-disciplinary problem, where the nonlinear structural dynamics, aerodynamics, and heat transfer models are coupled. A clear understanding of the impact of high-speed flow effects on the structural response, and the potential influence of the structure on the local environment, is needed in order to prevent the design of overly-conservative structures, a common problem in past hypersonic programs. The current work investigates these challenges from a structures perspective. To this end, the first part of this investigation looks at the modeling of the response of a rectangular panel to an external heating source (thermo-structural coupling) where the temperature effect on the structure is obtained from forward looking infrared (FLIR) measurements and the displacement via 3D-digital image correlation (DIC). The second part of the study uses data from a previous series of wind-tunnel experiments, performed to investigate the response of a compliant panel to the effects of high-speed flow, to train a pressure surrogate model. In this case, the panel aero-loading is obtained from fast-response pressure sensitive paint (PSP) measurements, both directly and from the pressure surrogate model. The result of this investigation is the use of full-field experimental measurements to update the structural model and train a computational efficient model of the loading environment. The use of reduced order models, informed by these full-field physical measurements, is a significant step toward the development of accurate simulation models of complex structures that are computationally tractable.

  8. Correlation between full-field and multifocal VEPs in optic neuritis.

    Science.gov (United States)

    Klistorner, Alexander; Fraser, Clare; Garrick, Raymond; Graham, Stuart; Arvind, Hemamalini

    2008-01-01

    To compare performance of multi-focal and full-field Visual Evoked Potentials (VEP) in patients with optic neuritis (ON). 26 patients with unilateral ON were enrolled. Multi-focal VEP (MF VEP) was recorded using AccuMaptrade mark system. Four bipolar channels were analysed. Full-field VEP (FF VEP) was performed according to ISCEV standard using ESPION with frontal-occipital electrode placement. Pattern-reversal protocol was implemented with check size of 60' and field of view of 30 degrees . For both tests amplitude and latency of affected eye were statistically different from non-affected eye. The asymmetry of amplitude and latency between two eyes was also very similar for both tests. Averaged Relative Asymmetry Coefficient of amplitude (RAC) for the FF VEP was 0.10 +/- 0.15 and for the MF VEP was 0.12 +/- 0.12 (P = 0.21, paired t-test). Averaged latency difference between affected and non-affected eyes was 13.0 +/- 12 ms for FF and 14.1 +/- 11.1 ms for MF VEPs (P = 0.14, paired t-test). Coefficient of correlation (r) of p100 component of the FF VEP and averaged MF VEP was 0.60 (P < 0.0001) for amplitude and 0.79 (P < 0.0001) for latency. Correlation improved when amplitude and latency asymmetry between two eyes was analysed (r = 0.81 and r = 0.92 respectively). Overall 73% of affected eyes were identified as abnormal by amplitude and/or latency of the FF VEP and 89% was considered abnormal when MF VEP was used. Analysis of individual cases revealed superior performance of MF VEP in detecting small or peripheral defects.

  9. Applying a Bayesian Approach to Identification of Orthotropic Elastic Constants from Full Field Displacement Measurements

    Science.gov (United States)

    Gogu, C.; Yin, W.; Haftka, R.; Ifju, P.; Molimard, J.; Le Riche, R.; Vautrin, A.

    2010-06-01

    A major challenge in the identification of material properties is handling different sources of uncertainty in the experiment and the modelling of the experiment for estimating the resulting uncertainty in the identified properties. Numerous improvements in identification methods have provided increasingly accurate estimates of various material properties. However, characterizing the uncertainty in the identified properties is still relatively crude. Different material properties obtained from a single test are not obtained with the same confidence. Typically the highest uncertainty is associated with respect to properties to which the experiment is the most insensitive. In addition, the uncertainty in different properties can be strongly correlated, so that obtaining only variance estimates may be misleading. A possible approach for handling the different sources of uncertainty and estimating the uncertainty in the identified properties is the Bayesian method. This method was introduced in the late 1970s in the context of identification [1] and has been applied since to different problems, notably identification of elastic constants from plate vibration experiments [2]-[4]. The applications of the method to these classical pointwise tests involved only a small number of measurements (typically ten natural frequencies in the previously cited vibration test) which facilitated the application of the Bayesian approach. For identifying elastic constants, full field strain or displacement measurements provide a high number of measured quantities (one measurement per image pixel) and hence a promise of smaller uncertainties in the properties. However, the high number of measurements represents also a major computational challenge in applying the Bayesian approach to full field measurements. To address this challenge we propose an approach based on the proper orthogonal decomposition (POD) of the full fields in order to drastically reduce their dimensionality. POD is

  10. Applying a Bayesian Approach to Identification of Orthotropic Elastic Constants from Full Field Displacement Measurements

    Directory of Open Access Journals (Sweden)

    Le Riche R.

    2010-06-01

    Full Text Available A major challenge in the identification of material properties is handling different sources of uncertainty in the experiment and the modelling of the experiment for estimating the resulting uncertainty in the identified properties. Numerous improvements in identification methods have provided increasingly accurate estimates of various material properties. However, characterizing the uncertainty in the identified properties is still relatively crude. Different material properties obtained from a single test are not obtained with the same confidence. Typically the highest uncertainty is associated with respect to properties to which the experiment is the most insensitive. In addition, the uncertainty in different properties can be strongly correlated, so that obtaining only variance estimates may be misleading. A possible approach for handling the different sources of uncertainty and estimating the uncertainty in the identified properties is the Bayesian method. This method was introduced in the late 1970s in the context of identification [1] and has been applied since to different problems, notably identification of elastic constants from plate vibration experiments [2]-[4]. The applications of the method to these classical pointwise tests involved only a small number of measurements (typically ten natural frequencies in the previously cited vibration test which facilitated the application of the Bayesian approach. For identifying elastic constants, full field strain or displacement measurements provide a high number of measured quantities (one measurement per image pixel and hence a promise of smaller uncertainties in the properties. However, the high number of measurements represents also a major computational challenge in applying the Bayesian approach to full field measurements. To address this challenge we propose an approach based on the proper orthogonal decomposition (POD of the full fields in order to drastically reduce their

  11. Full-Field Spectroscopy at Megahertz-frame-rates: Application of Coherent Time-Stretch Transform

    Science.gov (United States)

    DeVore, Peter Thomas Setsuda

    technique is not only four orders of magnitude faster than even the fastest (kHz) spectrometers, but will also enable capture of real-time complex dielectric function dynamics of plasmas and chemical reactions (e.g. combustion). It also has applications in high-energy physics, biology, and monitoring fast high-throughput industrial processes. Adding an electro-optic modulator to the Time-Stretch Transform yields time-to-time mapping of electrical waveforms. Known as TiSER, it is an analog slow-motion processor that uses light to reduce the bandwidth of broadband RF signals for capture by high-sensitivity analog-to-digital converters (ADC). However, the electro-optic modulator limits the electrical bandwidth of TiSER. To solve this, I introduced Optical Sideband-only Amplification, wherein electro-optically generated modulation (containing the RF information) is amplified at the expense of the carrier, addressing the two most important problems plaguing electro-optic modulators: (1) low RF bandwidth and (2) high required RF drive voltages. I demonstrated drive voltage reductions of 5x at 10 GHz and 10x at 50 GHz, while simultaneously increasing the RF bandwidth.

  12. Full-field, high-spatial-resolution detection of local structural damage from low-resolution random strain field measurements

    Science.gov (United States)

    Yang, Yongchao; Sun, Peng; Nagarajaiah, Satish; Bachilo, Sergei M.; Weisman, R. Bruce

    2017-07-01

    Structural damage is typically a local phenomenon that initiates and propagates within a limited area. As such high spatial resolution measurement and monitoring is often needed for accurate damage detection. This requires either significantly increased costs from denser sensor deployment in the case of global simultaneous/parallel measurements, or increased measurement time and labor in the case of global sequential measurements. This study explores the feasibility of an alternative approach to this problem: a computational solution in which a limited set of randomly positioned, low-resolution global strain measurements are used to reconstruct the full-field, high-spatial-resolution, two-dimensional (2D) strain field and rapidly detect local damage. The proposed approach exploits the implicit low-rank and sparse data structure of the 2D strain field: it is highly correlated without many edges and hence has a low-rank structure, unless damage-manifesting itself as sparse local irregularity-is present and alters such a low-rank structure slightly. Therefore, reconstruction of the full-field, high-spatial-resolution strain field from a limited set of randomly positioned low-resolution global measurements is modeled as a low-rank matrix completion framework and damage detection as a sparse decomposition formulation, enabled by emerging convex optimization techniques. Numerical simulations on a plate structure are conducted for validation. The results are discussed and a practical iterative global/local procedure is recommended. This new computational approach should enable the efficient detection of local damage using limited sets of strain measurements.

  13. 水稻高产创建栽培技术%High Yield and Create Cultivation Techniques of Rice

    Institute of Scientific and Technical Information of China (English)

    姜田英; 彭昌家

    2015-01-01

    This paper introduces the high yield and creates cultivation techniques of rice, such as the selection of seed, timely sowing, soil preparation,fertilization, specification transplanting, reasonable density planting, strengthen the man-agement of the field and timely harvest. To guide farmers to do scientific and reasonable rice super-high-yield strengthen-ing cultivation, improve the yield of rice and increase farmers' income, to ensure the rice production could continue to in-crease and ensure the safety of food production.%介绍了选用良种、适时播种、整好本田、配方施肥、规范移栽,合理密植、加强田间管理和适时收获等水稻高产创建栽培技术,旨在指导农民科学合理做好水稻超高产强化栽培,从而提高水稻单产,增加农民收益,确保水稻总产量持续增加,保障粮食生产安全。

  14. Full-field OCT for fast diagnostic of head and neck cancer

    Science.gov (United States)

    De Leeuw, Frederic; Casiraghi, Odile; Ben Lakhdar, Aïcha; Abbaci, Muriel; Laplace-Builhé, Corinne

    2015-02-01

    Full-Field OCT (FFOCT) produces optical slices of tissue using white light interferometry providing in-depth 2D images, with an isotropic resolution around 1 micrometer. These optical biopsy images are similar to those obtained with established histological procedures, but without tissue preparation and within few minutes. This technology could be useful when diagnosing a lesion or at the time of its surgical management. Here we evaluate the clinical value of FFOCT imaging in the management of patients with Head and Neck cancers by assessing the accuracy of the diagnosis done on FFOCT images from resected specimen. FFOCT images from Head and Neck samples were first compared to the gold standard (HES-conventional histology). An image atlas dedicated to the training of pathologists was built and diagnosis criteria were identified. Then, we performed a morphological correlative study: both healthy and cancerous samples from patients who undergo Head and Neck surgery of oral cavity, pharynx, and larynx were imaged. Images were interpreted in a random way by two pathologists and the FFOCT based diagnostics were compared with HES (gold standard) of the same samples. Here we present preliminary results showing that FFOCT provides a quick assessment of tissue architecture at microscopic level that could guide surgeons for tumor margin delineation during intraoperative procedure.

  15. Quality assessment of reverse engineering process based on full-field true-3D optical measurements

    Science.gov (United States)

    Kujawinska, Malgorzata; Sitnik, Robert

    2000-08-01

    In the paper the sequential steps of reverse engineering based on the data gathered by full-field optical system are discussed. Each step is concerned from the point of view of its influence on the final quality of the shape of manufactured object. At first the modern shape measurement system based on the combination of fringe projection, Grey code and experimental calibration is presented. The system enables the determination of absolute coordinates of the object measured from many directions. The dependence of the quality of the cloud of points on the type of object and the measurement procedure is discussed. Then the methods of transferring the experimental data into CAD/CAM/CAE system are presented. The quality of the virtual object in the form of closed triangular mesh is analyzed. Basing on this virtual object the copy of initial body is produced and measured. The accuracy of the object manufactured is determined and the main sources of errors are discussed. The modifications of the system and algorithms that minimize the errors are proposed. The reverse engineering sequence is presented is illustrated by several examples.

  16. Numerical focusing methods for full field OCT: a comparison based on a common signal model.

    Science.gov (United States)

    Kumar, Abhishek; Drexler, Wolfgang; Leitgeb, Rainer A

    2014-06-30

    In this paper a theoretical model of the full field swept source (FF SS) OCT signal is presented based on the angular spectrum wave propagation approach which accounts for the defocus error with imaging depth. It is shown that using the same theoretical model of the signal, numerical defocus correction methods based on a simple forward model (FM) and inverse scattering (IS), the latter being similar to interferometric synthetic aperture microscopy (ISAM), can be derived. Both FM and IS are compared quantitatively with sub-aperture based digital adaptive optics (DAO). FM has the least numerical complexity, and is the fastest in terms of computational speed among the three. SNR improvement of more than 10 dB is shown for all the three methods over a sample depth of 1.5 mm. For a sample with non-uniform refractive index with depth, FM and IS both improved the depth of focus (DOF) by a factor of 7x for an imaging NA of 0.1. DAO performs the best in case of non-uniform refractive index with respect to DOF improvement by 11x.

  17. Imaging of non tumorous and tumorous human brain tissue with full-field optical coherence tomography

    CERN Document Server

    Assayag, Osnath; Devaux, Bertrand; Harms, Fabrice; Pallud, Johan; Chretien, Fabrice; Boccara, Claude; Varlet, Pascale

    2013-01-01

    A prospective study was performed on neurosurgical samples from 18 patients to evaluate the use of Full-Field Optical Coherence Tomography (FF-OCT) in brain tumor diagnosis. FF-OCT captures en face slices of tissue samples at 1\\mum resolution in 3D with a typical 200\\mum imaging depth. A 1cm2 specimen is scanned at a single depth and processed in about 5 minutes. This rapid imaging process is non-invasive and 30 requires neither contrast agent injection nor tissue preparation, which makes it particularly well suited to medical imaging applications. Temporal chronic epileptic parenchyma and brain tumors such as meningiomas, low- grade and high-grade gliomas, and choroid plexus papilloma were imaged. A subpopulation of neurons, myelin fibers and CNS vasculature were clearly identified. Cortex could be discriminated from white matter, but individual glial cells as astrocytes (normal or reactive) or oligodendrocytes were not observable. This study reports for the first time on the feasibility of using FF-OCT in a...

  18. Hard X-ray Full Field Nano-imaging of Bone and Nanowires at SSRL

    Science.gov (United States)

    Andrews, Joy C.; Pianetta, Piero; Meirer, Florian; Chen, Jie; Almeida, Eduardo; van der Meulen, Marjolein C. H.; Alwood, Joshua S.; Lee, Cathy; Zhu, Jia; Cui, Yi

    2010-01-01

    A hard X-ray full field microscope from Xradia Inc. has been installed at SSRL on a 54-pole wiggler end station at beam line 6-2. It has been optimized to operate from 5–14 keV with resolution as high as 30 nm. High quality images are achieved using a vertical beam stabilizer and condenser scanner with high efficiency zone plates with 30 nm outermost zone width. The microscope has been used in Zernike phase contrast, available at 5.4 keV and 8 keV, as well as absorption contrast to image a variety of biological, environmental and materials samples. Calibration of the X-ray attenuation with crystalline apatite enabled quantification of bone density of plate-like and rod-like regions of mouse bone trabecula. 3D tomography of individual lacuna revealed the surrounding cell canaliculi and processes. 3D tomography of chiral branched PbSe nanowires showed orthogonal branches around a central nanowire. PMID:20871736

  19. From supersonic shear wave imaging to full-field optical coherence shear wave elastography

    Science.gov (United States)

    Nahas, Amir; Tanter, Mickaël; Nguyen, Thu-Mai; Chassot, Jean-Marie; Fink, Mathias; Claude Boccara, A.

    2013-12-01

    Elasticity maps of tissue have proved to be particularly useful in providing complementary contrast to ultrasonic imaging, e.g., for cancer diagnosis at the millimeter scale. Optical coherence tomography (OCT) offers an endogenous contrast based on singly backscattered optical waves. Adding complementary contrast to OCT images by recording elasticity maps could also be valuable in improving OCT-based diagnosis at the microscopic scale. Static elastography has been successfully coupled with full-field OCT (FF-OCT) in order to realize both micrometer-scale sectioning and elasticity maps. Nevertheless, static elastography presents a number of drawbacks, mainly when stiffness quantification is required. Here, we describe the combination of two methods: transient elastography, based on speed measurements of shear waves induced by ultrasonic radiation forces, and FF-OCT, an en face OCT approach using an incoherent light source. The use of an ultrafast ultrasonic scanner and an ultrafast camera working at 10,000 to 30,000 images/s made it possible to follow shear wave propagation with both modalities. As expected, FF-OCT is found to be much more sensitive than ultrafast ultrasound to tiny shear vibrations (a few nanometers and micrometers, respectively). Stiffness assessed in gel phantoms and an ex vivo rat brain by FF-OCT is found to be in good agreement with ultrasound shear wave elastography.

  20. Phase defect analysis with actinic full-field EUVL mask blank inspection

    Science.gov (United States)

    Yamane, Takeshi; Tanaka, Toshihiko; Terasawa, Tsuneo; Suga, Osamu

    2011-11-01

    We had developed an actinic full-field inspection system to detect multilayer phase-defects with dark field imaging. Regarding the actinic inspection of native defects, the influence of the defect's surface dimension and multilayer structure, on the intensity-signal obtained from the inspection was analyzed. Three mask blanks were inspected from which 55 defects, observed with AFM and SEM, were classified as amplitude-defects or phase-defects. The surface dimensions and SEVDs (sphere equivalent volume diameters) of the defects were measured with the AFM. In the case where their SEVDs were same as of the programmed phase-defects, they were found to produce stronger intensitysignals in comparison to the ones from the programmed phase-defects. Cross-sectional multilayer structures of two native phase-defects were observed with TEM, and those defects formed non-conformal structures in the multilayer. This result means that most of the native phase-defects tend to form a non-conformal structure, and can make large impact on the wafer image in comparison to the ones from a conformal structure. Besides phase-defects, the actinic inspection also detected amplitude-defects. Although the sensitivities of the amplitude-defects were found to be lower than those of the phase-defects, an amplitude-defect higher than 30 nm could be detected with high probability.

  1. Full-field speckle interferometry for non-contact photoacoustic tomography.

    Science.gov (United States)

    Horstmann, Jens; Spahr, Hendrik; Buj, Christian; Münter, Michael; Brinkmann, Ralf

    2015-05-21

    A full-field speckle interferometry method for non-contact and prospectively high speed Photoacoustic Tomography is introduced and evaluated as proof of concept. Thermoelastic pressure induced changes of the objects topography are acquired in a repetitive mode without any physical contact to the object. In order to obtain high acquisition speed, the object surface is illuminated by laser pulses and imaged onto a high speed camera chip. In a repetitive triple pulse mode, surface displacements can be acquired with nanometre sensitivity and an adjustable sampling rate of e.g. 20 MHz with a total acquisition time far below one second using kHz repetition rate lasers. Due to recurring interferometric referencing, the method is insensitive to thermal drift of the object due to previous pulses or other motion. The size of the investigated area and the spatial and temporal resolution of the detection are scalable. In this study, the approach is validated by measuring a silicone phantom and a porcine skin phantom with embedded silicone absorbers. The reconstruction of the absorbers is presented in 2D and 3D. The sensitivity of the measurement with respect to the photoacoustic detection is discussed. Potentially, Photoacoustic Imaging can be brought a step closer towards non-anaesthetized in vivo imaging and new medical applications not allowing acoustic contact, such as neurosurgical monitoring or burnt skin investigation.

  2. Fractal analysis of en face tomographic images obtained with full field optical coherence tomography

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Wanrong; Zhu, Yue [Department of Optical Engineering, Nanjing University of Science and Technology, Jiangsu (China)

    2017-03-15

    The quantitative modeling of the imaging signal of pathological areas and healthy areas is necessary to improve the specificity of diagnosis with tomographic en face images obtained with full field optical coherence tomography (FFOCT). In this work, we propose to use the depth-resolved change in the fractal parameter as a quantitative specific biomarker of the stages of disease. The idea is based on the fact that tissue is a random medium and only statistical parameters that characterize tissue structure are appropriate. We successfully relate the imaging signal in FFOCT to the tissue structure in terms of the scattering function and the coherent transfer function of the system. The formula is then used to analyze the ratio of the Fourier transforms of the cancerous tissue to the normal tissue. We found that when the tissue changes from the normal to cancerous the ratio of the spectrum of the index inhomogeneities takes the form of an inverse power law and the changes in the fractal parameter can be determined by estimating slopes of the spectra of the ratio plotted on a log-log scale. The fresh normal and cancer liver tissues were imaged to demonstrate the potential diagnostic value of the method at early stages when there are no significant changes in tissue microstructures. (copyright 2016 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. The SLcam: A full-field energy dispersive X-ray camera

    CERN Document Server

    Bjeoumikhov, A; Langhoff, N; Ordavo, I; Radtke, M; Reinholz, U; Riesemeier, H; Scharf, O; Soltau, H; Wedell, R

    2012-01-01

    The color X-ray camera (SLcam) is a full-field single photon imager. As stand-alone camera, it is applicable for energy and space-resolved X-ray detection measurements. The exchangeable poly-capillary optics in front of a beryllium entrance window conducts X-ray photons from the probe to distinguished energy dispersive pixels on a pnCCD. The dedicated software enables the acquisition and the online processing of the spectral data for all 69696 pixels, leading to a real-time visualization of the element distribution in a sample. No scanning system is employed. A first elemental composition image of the sample is visible within minutes while statistics is improving in the course of time. Straight poly-capillary optics allows for 1:1 imaging with a space resolution of 50 um and no limited depth of sharpness, ideal to map uneven objects. Using conically shaped optics, a magnification of 6 times was achieved with a space resolution of 10 um. We present a measurement with a laboratory source showing the camera capa...

  4. High-resolution handheld rigid endomicroscope based on full-field optical coherence tomography

    Science.gov (United States)

    Benoit a la Guillaume, Emilie; Martins, Franck; Boccara, Claude; Harms, Fabrice

    2016-02-01

    Full-field optical coherence tomography (FF-OCT) is a powerful tool for nondestructive assessment of biological tissue, i.e., for the structural examination of tissue in depth at a cellular resolution. Mostly known as a microscopy device for ex vivo analysis, FF-OCT has also been adapted to endoscopy setups since it shows good potential for in situ cancer diagnosis and biopsy guidance. Nevertheless, all the attempts to perform endoscopic FF-OCT imaging did not go beyond lab setups. We describe here, to the best of our knowledge, the first handheld FF-OCT endoscope based on a tandem interferometry assembly using incoherent illumination. A common-path passive imaging interferometer at the tip of an optical probe makes it robust and insensitive to environmental perturbations, and a low finesse Fabry-Perot processing interferometer guarantees a compact system. A good resolution (2.7 μm transverse and 6 μm axial) is maintained through the long distance, small diameter relay optics of the probe, and a good signal-to-noise ratio is achieved in a limited 100 ms acquisition time. High-resolution images and a movie of a rat brain slice have been recorded by moving the contact endoscope over the surface of the sample, allowing for tissue microscopic exploration at 20 μm under the surface. These promising ex vivo results open new perspectives for in vivo imaging of biological tissue, in particular, in the field of cancer and surgical margin assessment.

  5. Blind identification of full-field vibration modes from video measurements with phase-based video motion magnification

    Science.gov (United States)

    Yang, Yongchao; Dorn, Charles; Mancini, Tyler; Talken, Zachary; Kenyon, Garrett; Farrar, Charles; Mascareñas, David

    2017-02-01

    user supervision and calibration. First a multi-scale image processing method is applied on the frames of the video of a vibrating structure to extract the local pixel phases that encode local structural vibration, establishing a full-field spatiotemporal motion matrix. Then a high-spatial dimensional, yet low-modal-dimensional, over-complete model is used to represent the extracted full-field motion matrix using modal superposition, which is physically connected and manipulated by a family of unsupervised learning models and techniques, respectively. Thus, the proposed method is able to blindly extract modal frequencies, damping ratios, and full-field (as many points as the pixel number of the video frame) mode shapes from line of sight video measurements of the structure. The method is validated by laboratory experiments on a bench-scale building structure and a cantilever beam. Its ability for output (video measurements)-only identification and visualization of the weakly-excited mode is demonstrated and several issues with its implementation are discussed.

  6. Application of digital image correlation to full-field measurement of shrinkage strain of dental composites

    Institute of Scientific and Technical Information of China (English)

    Jian-ying LI; Andrew LAU; Alex S.L.FOK

    2013-01-01

    Objectives:Polymerization shrinkage of dental composites remains a major concern in restorative dentistry because it can lead to micro-cracking of the tooth and debonding at the tooth-restoration interface.The aim of this study was to measure the full-field polymerization shrinkage of dental composites using the optical digital image correlation (DIC) method and to evaluate how the measurement is influenced by the factors in experiment setup and image analysis.Methods:Four commercial dental composites,Premise Dentine,Z100,Z250 and Tetric EvoCeram,were tested.Composite was first placed into a slot mould to form a bar specimen with rectangular-section of 4 mm×2 mm,followed by the surface painting to create irregular speckles.Curing was then applied at one end of the specimen while the other part were covered against curing light for simulating the clinical curing condition of composite in dental cavity.The painted surface was recorded by a charge-coupled device (CCD) camera before and after curing.Subsequently,the volumetric shrinkage of the specimen was calculated with specialist DIC software based on image cross correlation.In addition,a few factors that may influence the measuring accuracy,including the subset window size,speckle size,illumination light and specimen length,were also evaluated.Results:The volumetric shrinkage of the specimen generally decreases with increasing distance from the irradiated surface with a conspicuous exception being the composite Premise Dentine as its maximum shrinkage occurred at a subsurface distance of about 1 mm instead of the irradiated surface.Zl00 had the greatest maximum shrinkage strain,followed by Z250,Tetric EvoCeram and then Premise Dentine.Larger subset window size made the shrinkage strain contour smoother.But the cost was that some details in the heterogeneity of the material were lost.Very small subset window size resulted in a lot of noise in the data,making it difficult to discern the general pattern in the strain

  7. Full field reservoir modeling of shale assets using advanced data-driven analytics

    Directory of Open Access Journals (Sweden)

    Soodabeh Esmaili

    2016-01-01

    Full Text Available Hydrocarbon production from shale has attracted much attention in the recent years. When applied to this prolific and hydrocarbon rich resource plays, our understanding of the complexities of the flow mechanism (sorption process and flow behavior in complex fracture systems - induced or natural leaves much to be desired. In this paper, we present and discuss a novel approach to modeling, history matching of hydrocarbon production from a Marcellus shale asset in southwestern Pennsylvania using advanced data mining, pattern recognition and machine learning technologies. In this new approach instead of imposing our understanding of the flow mechanism, the impact of multi-stage hydraulic fractures, and the production process on the reservoir model, we allow the production history, well log, completion and hydraulic fracturing data to guide our model and determine its behavior. The uniqueness of this technology is that it incorporates the so-called “hard data” directly into the reservoir model, so that the model can be used to optimize the hydraulic fracture process. The “hard data” refers to field measurements during the hydraulic fracturing process such as fluid and proppant type and amount, injection pressure and rate as well as proppant concentration. This novel approach contrasts with the current industry focus on the use of “soft data” (non-measured, interpretive data such as frac length, width, height and conductivity in the reservoir models. The study focuses on a Marcellus shale asset that includes 135 wells with multiple pads, different landing targets, well length and reservoir properties. The full field history matching process was successfully completed using this data driven approach thus capturing the production behavior with acceptable accuracy for individual wells and for the entire asset.

  8. Modified full-field optical coherence tomography: A novel tool for rapid histology of tissues

    Directory of Open Access Journals (Sweden)

    Manu Jain

    2011-01-01

    Full Text Available Background: Here, we report the first use of a commercial prototype of full-field optical coherence tomography called Light-CT TM . Based on the principle of white light interferometry, Light-CT TM generates quick high-resolution three-dimensional tomographic images from unprocessed tissues. Its advantage over the current intra-surgical diagnostic standard, i.e. frozen section analysis, lies in the absence of freezing artifacts, which allows real-time diagnostic impressions, and/or for the tissues to be triaged for subsequent conventional histopathology. Materials and Methods: In this study, we recapitulate known normal histology in nine formalin fixed ex vivo rat organs (skin, heart, lung, liver, stomach, kidney, prostate, urinary bladder, and testis. Large surface and virtually sectioned stacks of images at varying depths were acquired by a pair of 10x/0.3 numerical aperture water immersion objectives, processed and visualized in real time. Results: Normal histology of the following organs was recapitulated by identifying various tissue microstructures. Skin: epidermis, dermal-epidermal junction and hair follicles with surrounding sebaceous glands in the dermis. Stomach: mucosa with surface pits, submucosa, muscularis propria and serosa. Liver: hepatocytes separated by sinusoidal spaces, central veins and portal triad. Kidney: convoluted tubules, medullary rays (straight tubules and collecting ducts. Prostate: acini and fibro-muscular stroma. Lung: bronchi, bronchioles, alveolar ducts, alveoli and pleura. Urinary bladder: urothelium, lamina propria, muscularis propria, and serosa. Testis: seminiferous tubules with intra-tubular sperms. Conclusion: Light-CT TM is a powerful imaging tool to perform fast histology on fresh and fixed tissues, without introducing artifacts. Its compact size, ease of handling, fast image acquisition and safe incident light levels makes it well-suited for various intra-operative and intra-procedural triaging and

  9. Comparison of tissue equalization, and premium view post-processing methods in full field digital mammography

    Energy Technology Data Exchange (ETDEWEB)

    Chen Baoying, E-mail: chenby128@yahoo.co [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Wang Wei; Huang Jin; Zhao Ming; Cui Guangbin [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Xu Jing [Cell Engineering Research Centre and Department of Cell Biology, State Key Laboratory of Cancer Biology, Fourth Military Medical University, Changle West Road 169, 710032 Xi' an, Shaanxi (China); Guo Wei; Du Pang; Li Pei [Department of Radiology, Tangdu Hospital, Fourth Military Medical University, Xinsi Road 1, 710038 Xi' an, Shaanxi (China); Yu Jun, E-mail: pclamper@163.co [Department of Preclinical Experiment Center, Fourth Military Medical University, Changle West Road 169, 710032 Xi' an, Shaanxi (China)

    2010-10-15

    Objective: To retrospectively evaluate the diagnostic abilities of 2 post-processing methods provided by GE Senographe DS system, tissue equalization (TE) and premium view (PV) in full field digital mammography (FFDM). Materials and methods: In accordance with the ethical standards of the World Medical Association, this study was approved by regional ethics committee and signed informed patient consents were obtained. We retrospectively reviewed digital mammograms from 101 women (mean age, 47 years; range, 23-81 years) in the modes of TE and PV, respectively. Three radiologists, fully blinded to the post-processing methods, all patient clinical information and histologic results, read images by using objective image interpretation criteria for diagnostic information end points such as lesion border delineation, definition of disease extent, visualization of internal and surrounding morphologic features of the lesions. Also, overall diagnostic impression in terms of lesion conspicuity, detectability and diagnostic confidence was assessed. Between-group comparisons were performed with Wilcoxon signed rank test. Results: Readers 1, 2, and 3 demonstrated significant overall better impression of PV in 29, 27, and 24 patients, compared with that for TE in 12, 13, and 11 patients, respectively (p < 0.05). Significant (p < 0.05) better impression of PV was also demonstrated for diagnostic information end points. Importantly, PV proved to be more sensitive than TE while detecting malignant lesions in dense breast rather than benign lesions and malignancy in non-dense breast (p < 0.01). Conclusion: PV compared with TE provides marked better diagnostic information in FFDM, particularly for patients with malignancy in dense breast.

  10. Full-field illumination approach with multiple speckle for optical-resolution photoacoustic microscopy (Conference Presentation)

    Science.gov (United States)

    Poisson, Florian; Bossy, Emmanuel

    2016-03-01

    Optical-resolution photoacoustic endomicroscopy (OR-PAE) allows going beyond the limited penetration depth of conventional optical-resolution photoacoustic systems. Recently, it has been shown that OR-PAE may be performed through minimally invasive multimode fibers, by raster scanning a focus spot with optical wavefront shaping [1]. Here we introduce for the first time an approach to perform OR-PAE through a multimode fiber with a full-field illumination approach. By using multiple known speckle patterns, we show that it is possible to obtain optical-diffraction limited photoacoustic images, with the same resolution as that obtained by raster scanning a focus spot, i.e that of the speckle grain size. The fluctuations patterns of the photoacoustic amplitude at each pixel in the sample plane with the series of multiple speckle illumination were used to encode each pixel. This approach with known speckle illumination requires an initial calibration stage, that consists in learn a set of fluctuation patterns pixel per pixel, which will encode patterns each pixel of the scanned area. A point-like absorber was scanned across the filed-of-view during the calibration stage to acquire the reference patterns. Image reconstruction may be carried out by cross-correlating the series of photoacoustic amplitude measured with the sample to the reference patterns obtained during the calibration stage. In this work, the approach above was carried out both theoretically with Monte-carlo simulations and experimentally through a multi-mode fiber with samples made of absorbing spheres. [1] Papadopoulos et al., " Optical-resolution photoacoustic microscopy by use of a multimode fiber", Appl. Phys. Lett., 102(21), 2013

  11. Computer-aided detection system applied to full-field digital mammograms

    Energy Technology Data Exchange (ETDEWEB)

    Vega Bolivar, Alfonso; Sanchez Gomez, Sonia; Merino, Paula; Alonso-Bartolome, Pilar; Ortega Garcia, Estrella (Dept. of Radiology, Univ. Marques of Valdecilla Hospital, Santander (Spain)), e-mail: avegab@telefonica.net; Munoz Cacho, Pedro (Dept. of Statistics, Univ. Marques of Valdecilla Hospital, Santander (Spain)); Hoffmeister, Jeffrey W. (iCAD, Inc., Nashua, NH (United States))

    2010-12-15

    Background: Although mammography remains the mainstay for breast cancer screening, it is an imperfect examination with a sensitivity of 75-92% for breast cancer. Computer-aided detection (CAD) has been developed to improve mammographic detection of breast cancer. Purpose: To retrospectively estimate CAD sensitivity and false-positive rate with full-field digital mammograms (FFDMs). Material and Methods: CAD was used to evaluate 151 cases of ductal carcinoma in situ (DCIS) (n=48) and invasive breast cancer (n=103) detected with FFDM. Retrospectively, CAD sensitivity was estimated based on breast density, mammographic presentation, histopathology type, and lesion size. CAD false-positive rate was estimated with screening FFDMs from 200 women. Results: CAD detected 93% (141/151) of cancer cases: 97% (28/29) in fatty breasts, 94% (81/86) in breasts containing scattered fibroglandular densities, 90% (28/31) in heterogeneously dense breasts, and 80% (4/5) in extremely dense breasts. CAD detected 98% (54/55) of cancers manifesting as calcifications, 89% (74/83) as masses, and 100% (13/13) as mixed masses and calcifications. CAD detected 92% (73/79) of invasive ductal carcinomas, 89% (8/9) of invasive lobular carcinomas, 93% (14/15) of other invasive carcinomas, and 96% (46/48) of DCIS. CAD sensitivity for cancers 1-10 mm was 87% (47/54); 11-20 mm, 99% (70/71); 21-30 mm, 86% (12/14); and larger than 30 mm, 100% (12/12). The CAD false-positive rate was 2.5 marks per case. Conclusion: CAD with FFDM showed a high sensitivity in identifying cancers manifesting as calcifications or masses. CAD sensitivity was maintained in small lesions (1-20 mm) and invasive lobular carcinomas, which have lower mammographic sensitivity

  12. Full-field predictions of ice dynamic recrystallisation under simple shear conditions

    Science.gov (United States)

    Llorens, Maria-Gema; Griera, Albert; Bons, Paul D.; Lebensohn, Ricardo A.; Evans, Lynn A.; Jansen, Daniela; Weikusat, Ilka

    2016-09-01

    Understanding the flow of ice on the microstructural scale is essential for improving our knowledge of large-scale ice dynamics, and thus our ability to predict future changes of ice sheets. Polar ice behaves anisotropically during flow, which can lead to strain localisation. In order to study how dynamic recrystallisation affects to strain localisation in deep levels of polar ice sheets, we present a series of numerical simulations of ice polycrystals deformed under simple-shear conditions. The models explicitly simulate the evolution of microstructures using a full-field approach, based on the coupling of a viscoplastic deformation code (VPFFT) with dynamic recrystallisation codes. The simulations provide new insights into the distribution of stress, strain rate and lattice orientation fields with progressive strain, up to a shear strain of three. Our simulations show how the recrystallisation processes have a strong influence on the resulting microstructure (grain size and shape), while the development of lattice preferred orientations (LPO) appears to be less affected. Activation of non-basal slip systems is enhanced by recrystallisation and induces a strain hardening behaviour up to the onset of strain localisation and strain weakening behaviour. Simulations demonstrate that the strong intrinsic anisotropy of ice crystals is transferred to the polycrystalline scale and results in the development of strain localisation bands than can be masked by grain boundary migration. Therefore, the finite-strain history is non-directly reflected by the final microstructure. Masked strain localisation can be recognised in ice cores, such as the EDML, from the presence of stepped boundaries, microshear and grains with zig-zag geometries.

  13. Characterization of the effects of the FineView algorithm for full field digital mammography

    Science.gov (United States)

    Urbanczyk, H.; McDonagh, E.; Marshall, N. W.; Castellano, I.

    2012-04-01

    The aim of this study was to characterize the effect of an image processing algorithm (FineView) on both quantitative image quality parameters and the threshold contrast detail response of the GE Senographe DS full-field digital mammography system. The system was characterized using signal transfer property, pre-sampling modulation transfer function (MTF), normalized noise power spectrum (NNPS) and detective quantum efficiency (DQE) of the system. An algorithmic modulation transfer function (MTFa) was calculated from images acquired at a reduced detector air kerma (DAK) and with the FineView algorithm enabled. Two sets of beam conditions were used: Mo/Mo/28 kV and Rh/Rh/29 kV, both with 2 mm added Al filtration at the x-ray tube. Images were acquired with and without FineView at four DAK levels from 14 to 378 µGy. The threshold contrast detail response was assessed using the CDMAM contrast-detail test object which was imaged under standard clinical conditions with and without FineView at three DAK levels from 24 to 243 µGy. The images were scored by both human observers and by automated scoring software. Results indicated an improvement of up to 125% at 5 mm-1 in MTFa when FineView was activated, particularly at high DAK levels. A corresponding increase of up to 425% at 5 mm-1 was also seen in the NNPS, again with the same DAK dependence. FineView did not influence DQE, an indication that the signal to noise ratio transfer of the system remained unchanged. FineView did not affect the threshold contrast detectability of the system, a result that is consistent with the DQE results.

  14. Full Field X-Ray Fluorescence Imaging Using Micro Pore Optics for Planetary Surface Exploration

    Science.gov (United States)

    Sarrazin, P.; Blake, D. F.; Gailhanou, M.; Walter, P.; Schyns, E.; Marchis, F.; Thompson, K.; Bristow, T.

    2016-01-01

    Many planetary surface processes leave evidence as small features in the sub-millimetre scale. Current planetary X-ray fluorescence spectrometers lack the spatial resolution to analyse such small features as they only provide global analyses of areas greater than 100 mm(exp 2). A micro-XRF spectrometer will be deployed on the NASA Mars 2020 rover to analyse spots as small as 120m. When using its line-scanning capacity combined to perpendicular scanning by the rover arm, elemental maps can be generated. We present a new instrument that provides full-field XRF imaging, alleviating the need for precise positioning and scanning mechanisms. The Mapping X-ray Fluorescence Spectrometer - "Map-X" - will allow elemental imaging with approximately 100µm spatial resolution and simultaneously provide elemental chemistry at the scale where many relict physical, chemical and biological features can be imaged in ancient rocks. The arm-mounted Map-X instrument is placed directly on the surface of an object and held in a fixed position during measurements. A 25x25 mm(exp 2) surface area is uniformly illuminated with X-rays or alpha-particles and gamma-rays. A novel Micro Pore Optic focusses a fraction of the emitted X-ray fluorescence onto a CCD operated at a few frames per second. On board processing allows measuring the energy and coordinates of each X-ray photon collected. Large sets of frames are reduced into 2d histograms used to compute higher level data products such as elemental maps and XRF spectra from selected regions of interest. XRF spectra are processed on the ground to further determine quantitative elemental compositions. The instrument development will be presented with an emphasis on the characterization and modelling of the X-ray focussing Micro Pore Optic. An outlook on possible alternative XRF imaging applications will be discussed.

  15. Postoperative changes in the full-field electroretinogram following sevoflurane anaesthesia.

    LENUS (Irish Health Repository)

    Iohom, G

    2012-02-03

    BACKGROUND AND OBJECTIVE: We tested the hypothesis that disturbances of the visual pathway persist following general anaesthesia, even after normal clinical discharge criteria have been met. METHODS: We performed full-field flash electroretinography in the right eye of 10 unpremedicated ASA I patients who underwent N2O\\/sevoflurane anaesthesia. Electroretinograms were recorded preoperatively, immediately after discharge from the recovery room and 2 h after discontinuation of sevoflurane. The time at which postanaesthesia discharge score first exceeded 9 was also noted. Data were analysed using paired, one-tailed Student\\'s t-test. RESULTS: Latency of the b-wave on the photopic electroretinogram was greater at each postoperative time point (30.5 +\\/- 0.9 and 30 +\\/- 1.3 ms), compared to preoperative values (29.2 +\\/- 0.8 ms, P < 0.001 and P = 0.04, respectively). The A-B amplitude of the b-wave was less postoperatively (220.3 +\\/- 52.7 and 210.3 +\\/- 42.7 pV) compared to values before operation (248.1 +\\/- 57.6 microV, P = 0.03 and P = 0.01, respectively). Oscillatory potential latencies were greater at each postoperative time point (21.4 +\\/- 0.5 and 20.8 +\\/- 0.6 ms) compared to before operation (20.4 +\\/- 0.4 ms, P < 0.001 and P = 0.03, respectively). Oscillatory potential amplitudes were less at the first postoperative time point (17.5 +\\/- 6.1 microV), compared to preoperative values (22 +\\/- 6.4 microV, P = 0.04). CONCLUSIONS: Postoperative electroretinogram abnormalities are consistently present in patients who have undergone N2O\\/sevoflurane anaesthesia. These abnormalities persist beyond the time at which standard clinical discharge criteria have been met.

  16. Impact of full field digital mammography on the classification and mammographic characteristics of interval breast cancers

    Energy Technology Data Exchange (ETDEWEB)

    Knox, Mark, E-mail: marktknox@gmail.com; O’Brien, Angela, E-mail: angelaobrien@doctors.org.uk; Szabó, Endre, E-mail: endrebacsi@freemail.hu; Smith, Clare S., E-mail: csmith@mater.ie; Fenlon, Helen M., E-mail: helen.fenlon@cancerscreening.ie; McNicholas, Michelle M., E-mail: michelle.mcnicholas@cancerscreening.ie; Flanagan, Fidelma L., E-mail: fidelma.flanagan@cancerscreening.ie

    2015-06-15

    Highlights: • Digital mammography has changed the presentation of interval breast cancer. • Less interval breast cancers are associated with microcalcifications following FFDM. • Interval breast cancer audit remains a key feature of any breast screening program. - Abstract: Objective: Full field digital mammography (FFDM) is increasingly replacing screen film mammography (SFM) in breast screening programs. Interval breast cancers are an issue in all screening programs and the purpose of our study is to assess the impact of FFDM on the classification of interval breast cancers at independent blind review and to compare the mammographic features of interval cancers at FFDM and SFM. Materials and methods: This study included 138 cases of interval breast cancer, 76 following an FFDM screening examination and 62 following screening with SFM. The prior screening mammogram was assessed by each of five consultant breast radiologists who were blinded to the site of subsequent cancer. Subsequent review of the diagnostic mammogram was performed and cases were classified as missed, minimal signs, occult or true interval. Mammographic features of the interval cancer at diagnosis and any abnormality identified on the prior screening mammogram were recorded. Results: The percentages of cancers classified as missed at FFDM and SFM did not differ significantly, 10.5% (8 of 76) at FFDM and 8.1% (5 of 62) at SFM (p = .77). There were significantly less interval cancers presenting as microcalcifications (alone or in association with another abnormality) following screening with FFDM, 16% (12 of 76) than following a SFM examination, 32% (20 of 62) (p = .02). Conclusion: Interval breast cancers continue to pose a problem at FFDM. The switch to FFDM has changed the mammographic presentation of interval breast cancer, with less interval cancers presenting in association with microcalcifications.

  17. Full field reservoir modeling of shale assets using advanced data-driven analytics

    Institute of Scientific and Technical Information of China (English)

    Soodabeh Esmaili; Shahab D. Mohaghegh

    2016-01-01

    Hydrocarbon production from shale has attracted much attention in the recent years. When applied to this prolific and hydrocarbon rich resource plays, our understanding of the complexities of the flow mechanism (sorption process and flow behavior in complex fracture systems-induced or natural) leaves much to be desired. In this paper, we present and discuss a novel approach to modeling, history matching of hydrocarbon production from a Marcellus shale asset in southwestern Pennsylvania using advanced data mining, pattern recognition and machine learning technologies. In this new approach instead of imposing our understanding of the flow mechanism, the impact of multi-stage hydraulic fractures, and the production process on the reservoir model, we allow the production history, well log, completion and hydraulic fracturing data to guide our model and determine its behavior. The uniqueness of this tech-nology is that it incorporates the so-called “hard data” directly into the reservoir model, so that the model can be used to optimize the hydraulic fracture process. The “hard data” refers to field measure-ments during the hydraulic fracturing process such as fluid and proppant type and amount, injection pressure and rate as well as proppant concentration. This novel approach contrasts with the current industry focus on the use of “soft data” (non-measured, interpretive data such as frac length, width, height and conductivity) in the reservoir models. The study focuses on a Marcellus shale asset that in-cludes 135 wells with multiple pads, different landing targets, well length and reservoir properties. The full field history matching process was successfully completed using this data driven approach thus capturing the production behavior with acceptable accuracy for individual wells and for the entire asset.

  18. Defect Localization Capabilities of a Global Detection Scheme: Spatial Pattern Recognition Using Full-field Vibration Test Data in Plates

    Science.gov (United States)

    Saleeb, A. F.; Prabhu, M.; Arnold, S. M. (Technical Monitor)

    2002-01-01

    Recently, a conceptually simple approach, based on the notion of defect energy in material space has been developed and extensively studied (from the theoretical and computational standpoints). The present study focuses on its evaluation from the viewpoint of damage localization capabilities in case of two-dimensional plates; i.e., spatial pattern recognition on surfaces. To this end, two different experimental modal test results are utilized; i.e., (1) conventional modal testing using (white noise) excitation and accelerometer-type sensors and (2) pattern recognition using Electronic speckle pattern interferometry (ESPI), a full field method capable of analyzing the mechanical vibration of complex structures. Unlike the conventional modal testing technique (using contacting accelerometers), these emerging ESPI technologies operate in a non-contacting mode, can be used even under hazardous conditions with minimal or no presence of noise and can simultaneously provide measurements for both translations and rotations. Results obtained have clearly demonstrated the robustness and versatility of the global NDE scheme developed. The vectorial character of the indices used, which enabled the extraction of distinct patterns for localizing damages proved very useful. In the context of the targeted pattern recognition paradigm, two algorithms were developed for the interrogation of test measurements; i.e., intensity contour maps for the damaged index, and the associated defect energy vector field plots.

  19. Effect of Collection Technique on Yield of Bovine Oocytes and the Development Potential of Oocytes from Different Grades of Oocytes

    Directory of Open Access Journals (Sweden)

    R.G Sianturi

    2002-10-01

    Full Text Available Oocyte collection technique is important to obtain a maximum number of oocytes to be employed on in vitro production of embryos. In this study, immature bovine oocytes were collected from slaughterhouse ovaries by two techniques: aspiration of 2- to 6-mm follicles and slicing. Following collection, oocyte qualities were classified into four categories (A, B, C, and D on the basis of cumulus attachment. Oocytes of each category were matured in vitro in CO2 incubator for 22-24 hours and cumulus expansion and maturation rates were observed. The total number of oocytes (group A+B+C+D and yield of good quality oocytes (only group A and B recovered per ovary by aspiration were 12.02 and 8.21, and by slicing were 29.38 and 19.65 (P<0.01, respectively. The total cumulus cells expansion rates of A, B, C and D oocytes were 97.1%, 88.3%, 6.0% and 20.6% respectively. Maturation rates for A, B and C categories of oocytes were 91.4%, 82.3% and 35.0% respectively while no matured oocyte was observed for group D oocytes. Maturation rates were significantly different between group A and C and also between B and C but not between A and B (P<0.05. In conclusion, slicing technique recovered more oocytes per ovary (2.4 times than that of aspiration and the best maturation rate was observed from category A oocytes which surrounded by more than 3 layers of cumulus cells. However oocytes of category A and B can be considered as good quality oocytes.

  20. Normal Values of Standard Full Field Electroretinography in an Iranian Population

    Directory of Open Access Journals (Sweden)

    Mohammad-Mehdi Parvaresh

    2009-04-01

    Full Text Available

    PURPOSE: To determine normal values of standard full-field electroretinography (ERG and to evaluate their variations with age in an Iranian population. METHODS: Through convenient sampling, 170 normal subjects 1-80 years of age were selected from residents of Tehran. ERG amplitudes and implicit time values were measured according to recommendations by the International Society for Clinical Electrophysiology of Vision. Evaluations consisted of light-adapted ERG including single-white flash and 30-Hz flicker response; and dark-adapted ERG including rod, maximal dark-adapted and cone responses. RESULTS: No significant difference in ERG values was observed between men and women, or between right and left eyes. ERG amplitudes were lower (P=0.04 and implicit time values were greater (P=0.03 in subjects 70-80 years of age as compared to younger individuals. CONCLUSIONS: ERG parameters are significantly diminished with age. Our results may serve as a reference against which standard ERG responses can be compared.

  1. Detector evaluation of a prototype amorphous selenium-based full field digital mammography system

    Science.gov (United States)

    Jesneck, Jonathan L.; Saunders, Robert S.; Samei, Ehsan; Xia, Jessie Q.; Lo, Joseph Y.

    2005-04-01

    This study evaluated the physical performance of a selenium-based direct full-field digital mammography prototype detector (Siemens Mammomat NovationDR), including the pixel value vs. exposure linearity, the modulation transfer function (MTF), the normalized noise power spectrum (NNPS), and the detective quantum efficiency (DQE). The current detector is the same model which received an approvable letter from FDA for release to the US market. The results of the current prototype are compared to those of an earlier prototype. Two IEC standard beam qualities (RQA-M2: Mo/Mo, 28 kVp, 2 mm Al; RQA-M4: Mo/Mo, 35 kVp, 2 mm Al) and two additional beam qualities (MW2: W/Rh, 28 kVp, 2 mm Al; MW4: W/Rh, 35 kVp, 2 mm Al) were investigated. To calculate the modulation transfer function (MTF), a 0.1 mm Pt-Ir edge was imaged at each beam quality. Detector pixel values responded linearly against exposure values (R2 0.999). As before, above 6 cycles/mm Mo/Mo MTF was slightly higher along the chest-nipple axis compared to the left-right axis. MTF was comparable to the previously reported prototype, with slightly reduced resolution. The DQE peaks ranged from 0.71 for 3.31 μC/kg (12.83 mR) to 0.4 for 0.48 μC/kg (1.86 mR) at 1.75 cycles/mm for Mo/Mo at 28 kVp. The DQE range for W/Rh at 28 kVP was 0.81 at 2.03 μC/kg (7.87 mR) to 0.50 at 0.50 μC/kg (1.94 mR) at 1 cycle/mm. NNPS tended to increase with greater exposures, while all exposures had a significant low-frequency component. Bloom and detector edge artifacts observed previously were no longer present in this prototype. The new detector shows marked noise improvement, with slightly reduced resolution. There remain artifacts due to imperfect gain calibration, but at a reduced magnitude compared to a prototype detector.

  2. Regularized discriminate analysis for breast mass detection on full field digital mammograms

    Science.gov (United States)

    Wei, Jun; Sahiner, Berkman; Zhang, Yiheng; Chan, Heang-Ping; Hadjiiski, Lubomir M.; Zhou, Chuan; Ge, Jun; Wu, Yi-Ta

    2006-03-01

    In computer-aided detection (CAD) applications, an important step is to design a classifier for the differentiation of the abnormal from the normal structures. We have previously developed a stepwise linear discriminant analysis (LDA) method with simplex optimization for this purpose. In this study, our goal was to investigate the performance of a regularized discriminant analysis (RDA) classifier in combination with a feature selection method for classification of the masses and normal tissues detected on full field digital mammograms (FFDM). The feature selection scheme combined a forward stepwise feature selection process and a backward stepwise feature elimination process to obtain the best feature subset. An RDA classifier and an LDA classifier in combination with this new feature selection method were compared to an LDA classifier with stepwise feature selection. A data set of 130 patients containing 260 mammograms with 130 biopsy-proven masses was used. All cases had two mammographic views. The true locations of the masses were identified by experienced radiologists. To evaluate the performance of the classifiers, we randomly divided the data set into two independent sets of approximately equal size for training and testing. The training and testing were performed using the 2-fold cross validation method. The detection performance of the CAD system was assessed by free response receiver operating characteristic (FROC) analysis. The average test FROC curve was obtained by averaging the FP rates at the same sensitivity along the two corresponding test FROC curves from the 2-fold cross validation. At the case-based sensitivities of 90%, 80% and 70% on the test set, our RDA classifier with the new feature selection scheme achieved an FP rate of 1.8, 1.1, and 0.6 FPs/image, respectively, compared to 2.1, 1.4, and 0.8 FPs/image with stepwise LDA with simplex optimization. Our results indicate that RDA in combination with the sequential forward inclusion

  3. Design and performance of the prototype full field breast tomosynthesis system with selenium based flat panel detector

    Science.gov (United States)

    Ren, Baorui; Ruth, Chris; Stein, Jay; Smith, Andrew; Shaw, Ian; Jing, Zhenxue

    2005-04-01

    We have developed a breast tomosynthesis system utilizing a selenium-based direct conversion flat panel detector. This prototype system is a modification of Selenia, Hologic"s full field digital mammography system, using an add-on breast holding device to allow 3D tomosynthetic imaging. During a tomosynthesis scan, the breast is held stationary while the x-ray source and detector mounted on a c-arm rotate continuously around the breast over an angular range up to 30 degrees. The x-ray tube is pulsed to acquire 11 projections at desired c-arm angles. Images are reconstructed in planes parallel to the breastplate using a filtered backprojection algorithm. Processing time is typically 1 minute for a 50 mm thick breast at 0.1 mm in-plane pixel size, 1 mm slice-to-slice separation. Clinical studies are in progress. Performance evaluations were carried out at the system and the subsystem levels including spatial resolution, signal-to-noise ratio, spectra optimization, imaging technique, and phantom and patient studies. Experimental results show that we have successfully built a tomosynthesis system with images showing less structure noise and revealing 3D information compared with the conventional mammogram. We introduce, for the first time, the definition of "Depth of Field" for tomosynthesis based on a spatial resolution study. This parameter is used together with Modulation Transfer Function (MTF) to evaluate 3D resolution of a tomosynthesis system as a function of system design, imaging technique, and reconstruction algorithm. Findings from the on-going clinical studies will help the design of the next generation tomosynthesis system offering improved performance.

  4. Large-scale full-field metrology using projected fringes: some challenges and solutions

    Science.gov (United States)

    Huntley, Jonathan M.; Ogundana, Tokunbo; Burguete, Richard L.; Coggrave, C. Russell

    2007-06-01

    The application of optical techniques to the measurement of shape and deformation of structures in the aerospace industry poses unique challenges resulting from the large length scales involved, which are typically in the 1-10 m range. For example, the relative immobility of large samples requires a network of sensors to be linked into a common global coordinate system; traceable calibration requires the development of new types of calibration artefact; and traditional interferometric techniques for displacement field mapping are frequently too sensitive to observe the physical effect of interest. We describe a system designed to address some of these problems based on the projected fringe technique combined with temporal phase unwrapping. Multiple cameras and projectors are linked into a common coordinate system using calibration concepts borrowed from the photogrammetry field. Traceable calibration is achieved through the use of reference spheres separated by a bar of known length. Traditional two-dimensional image processing techniques for recognizing circles (Hough transforms) have been extended to the automatic detection of spheres within the measured 3-D point clouds. Bundle adjustment software has been developed to refine the camera and projector calibration parameters as well as the rigid body translation and rotation coordinates defining the poses of the calibration artefact. An overview of all these aspects of the developed techniques is given in the paper. Typical results from a compression test on a large scale aluminium structure, performed on-site at Airbus UK using the developed system, are also presented.

  5. Non-null full field X-ray mirror metrology using SCOTS: a reflection deflectometry approach.

    Science.gov (United States)

    Su, Peng; Wang, Yuhao; Burge, James H; Kaznatcheev, Konstantine; Idir, Mourad

    2012-05-21

    In a previous paper, the University of Arizona (UA) has developed a measurement technique called: Software Configurable Optical Test System (SCOTS) based on the principle of reflection deflectometry. In this paper, we present results of this very efficient optical metrology method applied to the metrology of X-ray mirrors. We used this technique to measure surface slope errors with precision and accuracy better than 100 nrad (rms) and ~200 nrad (rms), respectively, with a lateral resolution of few mm or less. We present results of the calibration of the metrology systems, discuss their accuracy and address the precision in measuring a spherical mirror.

  6. Demonstration of full-field patterning of 32 nm test chips using EUVL

    Science.gov (United States)

    Vandentop, Gilroy; Chandhok, Manish; Putna, Ernisse S.; Younkin, Todd R.; Clarke, James S.; Carson, Steven; Myers, Alan; Leeson, Michael; Zhang, Guojing; Liang, Ted; Murachi, Tetsunori

    2009-03-01

    EUV lithography is considered one of the options for high volume manufacturing (HVM) of 16 nm MPU node devices [1]. The benefits of high k1(~0.5) imaging enable EUVL to simplify the patterning process and ease design rule restrictions. However, EUVL with its unique imaging process - reflective optics and masks, vacuum operation, and lack of pellicle, has several challenges to overcome before being qualified for production. Thus, it is important to demonstrate the capability to integrate EUVL into existing process flows and characterize issues which could hamper yield. A patterning demonstration of Intel's 32 nm test chips using the ADT at IMEC [7] is presented, This test chip was manufactured using processes initially developed with the Intel MET [2-4] as well as masks made by Intel's mask shop [5,6]. The 32 nm node test chips which had a pitch of 112.5 nm at the trench layer, were patterned on the ADT which resulted in a large k1 factor of 1 and consequently, the trench process window was iso-focal with MEEF = 1. It was found that all mask defects detected by a mask pattern inspection tool printed on the wafer and that 90% of these originated from the substrate. We concluded that improvements are needed in mask defects, photospeed of the resist, overlay, and tool throughput of the tool to get better results to enable us to ultimately examine yield.

  7. Evaluation of Biomass Yield and Water Treatment in Two Aquaponic Systems Using the Dynamic Root Floating Technique (DRF

    Directory of Open Access Journals (Sweden)

    Laura Silva

    2015-11-01

    Full Text Available The experiment evaluates the food production and water treatment of TAN, NO2−–N, NO3−–N, and PO43− in two aquaponics systems using the dynamic root floating technique (DRF. A separate recirculation aquaculture system (RAS was used as a control. The fish cultured was Nile tilapia (Oreochromis niloticus. The hydroponic culture in one treatment (PAK was pak choy (Brassica chinensis, and in the other (COR coriander (Coriandrum sativum. Initial and final weights were determined for the fish culture. Final edible fresh weight was determined for the hydroponic plant culture. TAN, NO2−–N, NO3−–N, and PO43− were measured in fish culture and hydroponic culture once a week at two times, morning (9:00 a.m. and afternoon (3:00 p.m.. The fish biomass production was not different in any treatment (p > 0.05 and the total plant yield was greater (p < 0.05 in PAK than in COR. For the hydroponic culture in the a.m., the PO43− was lower (p < 0.05 in the PAK treatment than in COR, and in the p.m. NO3−–N and PO43− were lower (p < 0.05 in PAK than in COR. The PAK treatment demonstrated higher food production and water treatment efficiency than the other two treatments.

  8. Evaluation of Image Processing Technique for Measuring of Nitrogen and Yield in Paddy Rice and Comparing it with Standard Methods

    Directory of Open Access Journals (Sweden)

    M.R Larijani

    2016-04-01

    Full Text Available In order to use new and low cost methods in precision agriculture, nitrogen should be supplied for plants on time and precisely. For determining the required nitrogen of paddy rice in the clustering stage, a series of experiments were conducted using three different methods of: image processing, kjeldahl and chlorophyll meter set (SPAD-502, in a randomized complete block design with three replications during 2010 at Rice Research Center of Tonekabon, Iran. Four experimental treatments were different level of fertilizer (Urea with 46% nitrogen. In the clustering stage, some images from rice plants were taken vertically by a digital camera and were analyzed using image processing technique. Simultaneously the chlorophyll index of plants was measured by SPAD-502 chlorophyll meter set and the percentage amount of nitrogen was measured using of the so called kjeldahl laboratory method. The results showed that the three methods of determining nitrogen of rice plant were highly correlated. Moreover, the correlation among the three methods and crop yield were almost the same. In general, the method of image processing could have a high potential for nitrogen management in the field, while this method was low-cost, faster and also nondestructive in comparison to the other methods.

  9. Dynamic full field OCT: metabolic contrast at subcellular level (Conference Presentation)

    Science.gov (United States)

    Apelian, Clement; Harms, Fabrice; Thouvenin, Olivier; Boccara, Claude A.

    2016-03-01

    Cells shape or density is an important marker of tissues pathology. However, individual cells are difficult to observe in thick tissues frequently presenting highly scattering structures such as collagen fibers. Endogenous techniques struggle to image cells in these conditions. Moreover, exogenous contrast agents like dyes, fluorophores or nanoparticles cannot always be used, especially if non-invasive imaging is required. Scatterers motion happening down to the millisecond scale, much faster than the still and highly scattering structures (global motion of the tissue), allowed us to develop a new approach based on the time dependence of the FF-OCT signals. This method reveals hidden cells after a spatiotemporal analysis based on singular value decomposition and wavelet analysis concepts. It does also give us access to local dynamics of imaged scatterers. This dynamic information is linked with the local metabolic activity that drives these scatterers. Our technique can explore subcellular scales with micrometric resolution and dynamics ranging from the millisecond to seconds. By this mean we studied a wide range of tissues, animal and human in both normal and pathological conditions (cancer, ischemia, osmotic shock…) in different organs such as liver, kidney, and brain among others. Different cells, undetectable with FF-OCT, were identified (erythrocytes, hepatocytes…). Different scatterers clusters express different characteristic times and thus can be related to different mechanisms that we identify with metabolic functions. We are confident that the D-FFOCT, by accessing to a new spatiotemporal metabolic contrast, will be a leading technique on tissue imaging and for better medical diagnosis.

  10. Full field residual stress determination using hole-drilling and electronic speckle pattern interferometry (ESPI with phase unwrapping method

    Directory of Open Access Journals (Sweden)

    Lyu B.I.

    2010-06-01

    Full Text Available The hole-drilling strain gauge technique has become a standard method in measuring residual stresses [1]. Moiré interferometry combining hole-drilling method opens additional opportunity for full-field residual stress measurement using optical interferometry [2]. The optical moiré method has a non-contact feature comparing with strain gauge method. Yet Moiré interferometry suffers a drawback in its complicated grating preparation on one hand and it is difficult to be applied to work piece with complicated geometry on the other hand. Electronic speckle pattern interferometry (ESPI provides information about the displacement field of a surface and it can be conveniently used on asreceived surfaces without special surface preparation and can be applied to work piece with complicated geometry that may be unsuitable for applying strain gauge or gratings. Studies on combining ESPI with hole-drilling show that is feasible to obtain reasonable residual stress values [3, 4]. The purpose of this study was to demonstrate the detail of hole-drilling technique combining ESPI with phase unwrapping method to reveal the full field stress distribution and to measure the associated stress field on a thin specimen exerted by a uni-axial load. This study also demonstrates the noise reduction achieved by Gaussian low pass filter and a successful phase unwrapping resulted from five-step phase shifting and cellular automata method. Figure 1 shows the experimental setup of the ESPI system and the hole-drilling system. The light from a laser source is split into two beams. One split beam emerges from a PZT-stage to provide stepwise phase shifting and it further interferes with the other split image beam on the specimen surface to produce speckle patterns onto the CCD camera. By recording the speckle images of stepwise phase shifting before and after hole-drilling, the fringe patterns at each step can be obtained. Through a uniaxial loading fixture loads with

  11. Evaluation of automatic exposure control performance in full-field digital mammography systems using contrast-detail analysis

    Science.gov (United States)

    Suarez Castellanos, Ivan M.; Kaczmarek, Richard; Brunner, Claudia C.; de Las Heras, Hugo; Liu, Haimo; Chakrabarti, Kish

    2012-03-01

    Full Field Digital Mammography (FFDM) is increasingly replacing screen-film systems for screening and diagnosis of breast abnormalities. All FFDM systems are equipped with an Automatic Exposure Control (AEC) which automatically selects technique factors to optimize dose and image quality. It is therefore crucial that AEC performance is properly adjusted and optimized to different breast thicknesses. In this work, we studied the AEC performance of three widely used FFDM systems using the CDMAM and QUART mam/digi phantoms. We used the CDMAM phantom to generate Contrast-Detail (C-D) curves for each AEC mode available in the FFDM systems under study for phantoms with equivalent X-Ray attenuation properties as 3.2 cm, 6 cm and 7.5 cm thick breasts. Generated C-D curves were compared with ideal C-D curves constructed using a metric referred to as the k-factor which is the product of the thickness and the diameter of the smallest correctly identified disks in the CDMAM phantom. Previous observer studies have indicated that k-factor values of 60 to 80 μm2 are particularly useful in demonstrating the threshold for object detectability for detectors used in digital mammography systems. The QUART mam/digi phantom was used to calculate contrast-to-noise ratio (CNR) values at different phantom thicknesses. The results of the C-D analysis and CNR measurements were used to determine limiting CNR values intended to provide a threshold for proper image quality assessment. The results of the Contrast-Detail analysis show that for two of the three evaluated FFDM systems, at higher phantom thicknesses, low contrast signal detectability gets worse. This agrees with the results obtained with the QUART mam/digi phantom, where CNR decreases below determined limiting CNR values.

  12. Subcellular metabolic contrast in living tissue using dynamic full field OCT (D-FFOCT) (Conference Presentation)

    Science.gov (United States)

    Apelian, Clement; Harms, Fabrice; Thouvenin, Olivier; Boccara, Claude A.

    2016-03-01

    Cells shape or density is an important marker of tissues pathology. However, individual cells are difficult to observe in thick tissues frequently presenting highly scattering structures such as collagen fibers. Endogenous techniques struggle to image cells in these conditions. Moreover, exogenous contrast agents like dyes, fluorophores or nanoparticles cannot always be used, especially if non-invasive imaging is required. Scatterers motion happening down to the millisecond scale, much faster than the fix and highly scattering structures (global motion of the tissue), allowed us to develop a new approach based on the time dependence of the FF-OCT signals. This method reveals hidden cells after a spatiotemporal analysis based on singular value decomposition and wavelet analysis concepts. It does also give us access to local dynamics of imaged scatterers. This dynamic information is linked with the local metabolic activity that drives these scatterers. Our technique can explore subcellular scales with micrometric resolution and dynamics ranging from the millisecond to seconds. By this mean we studied a wide range of tissues, animal and human in both normal and pathological conditions (cancer, ischemia, osmotic shock…) in different organs such as liver, kidney, and brain among others. Different cells, undetectable with FF-OCT, were identified (erythrocytes, hepatocytes…). Different scatterer clusters express different characteristic times and thus can be related to different mechanisms that we identify with metabolic functions. We are confident that the D-FFOCT, by accessing to a new spatiotemporal metabolic contrast, will be a leading technique on tissue imaging and could lead to better medical diagnosis.

  13. Assessment of Breast, Brain and Skin Pathological Tissue Using Full Field OCM

    Science.gov (United States)

    Dalimier, Eugénie; Assayag, Osnath; Harms, Fabrice; Boccara, A. Claude

    The aim of this chapter is to assess whether the images of the breast, brain, and skin tissue obtained by FFOCM contain sufficient detail to allow pathologists to make a diagnosis of cancer and other pathologies comparable to what was obtained by conventional histological techniques. More precisely, it is necessary to verify on FFOCM images if it is possible to differentiate a healthy area from a pathological area. The reader interested in other organs or in animal studies may find a large number of 2D or 3D images in the atlas [2].

  14. Full-Field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

    Science.gov (United States)

    Littell, Justin D.; Binienda, Wieslaw K.; Goldberg, Robert K.; Roberts, Gary D.

    2008-01-01

    Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape out of triaxial braided composite materials. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A more detailed investigation of deformation and failure processes in large-unit-cell-size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. This report presents some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12- and 24-k yarns and a 0 /+60 /-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed and correlations were made between these local failures and global composite deformation and strength.

  15. Efficient formulations of the material identification problem using full-field measurements

    Science.gov (United States)

    Pérez Zerpa, Jorge M.; Canelas, Alfredo

    2016-08-01

    The material identification problem addressed consists of determining the constitutive parameters distribution of a linear elastic solid using displacement measurements. This problem has been considered in important applications such as the design of methodologies for breast cancer diagnosis. Since the resolution of real life problems involves high computational costs, there is great interest in the development of efficient methods. In this paper two new efficient formulations of the problem are presented. The first formulation leads to a second-order cone optimization problem, and the second one leads to a quadratic optimization problem, both allowing the resolution of the problem with high efficiency and precision. Numerical examples are solved using synthetic input data with error. A regularization technique is applied using the Morozov criterion along with an automatic selection strategy of the regularization parameter. The proposed formulations present great advantages in terms of efficiency, when compared to other formulations that require the application of general nonlinear optimization algorithms.

  16. 3D fingerprint imaging system based on full-field fringe projection profilometry

    Science.gov (United States)

    Huang, Shujun; Zhang, Zonghua; Zhao, Yan; Dai, Jie; Chen, Chao; Xu, Yongjia; Zhang, E.; Xie, Lili

    2014-01-01

    As an unique, unchangeable and easily acquired biometrics, fingerprint has been widely studied in academics and applied in many fields over the years. The traditional fingerprint recognition methods are based on the obtained 2D feature of fingerprint. However, fingerprint is a 3D biological characteristic. The mapping from 3D to 2D loses 1D information and causes nonlinear distortion of the captured fingerprint. Therefore, it is becoming more and more important to obtain 3D fingerprint information for recognition. In this paper, a novel 3D fingerprint imaging system is presented based on fringe projection technique to obtain 3D features and the corresponding color texture information. A series of color sinusoidal fringe patterns with optimum three-fringe numbers are projected onto a finger surface. From another viewpoint, the fringe patterns are deformed by the finger surface and captured by a CCD camera. 3D shape data of the finger can be obtained from the captured fringe pattern images. This paper studies the prototype of the 3D fingerprint imaging system, including principle of 3D fingerprint acquisition, hardware design of the 3D imaging system, 3D calibration of the system, and software development. Some experiments are carried out by acquiring several 3D fingerprint data. The experimental results demonstrate the feasibility of the proposed 3D fingerprint imaging system.

  17. Full-field mapping of internal strain distribution in red sandstone specimen under compression using digital volumetric speckle photography and X-ray computed tomography

    Directory of Open Access Journals (Sweden)

    Lingtao Mao

    2015-04-01

    Full Text Available It is always desirable to know the interior deformation pattern when a rock is subjected to mechanical load. Few experimental techniques exist that can represent full-field three-dimensional (3D strain distribution inside a rock specimen. And yet it is crucial that this information is available for fully understanding the failure mechanism of rocks or other geomaterials. In this study, by using the newly developed digital volumetric speckle photography (DVSP technique in conjunction with X-ray computed tomography (CT and taking advantage of natural 3D speckles formed inside the rock due to material impurities and voids, we can probe the interior of a rock to map its deformation pattern under load and shed light on its failure mechanism. We apply this technique to the analysis of a red sandstone specimen under increasing uniaxial compressive load applied incrementally. The full-field 3D displacement fields are obtained in the specimen as a function of the load, from which both the volumetric and the deviatoric strain fields are calculated. Strain localization zones which lead to the eventual failure of the rock are identified. The results indicate that both shear and tension are contributing factors to the failure mechanism.

  18. Quantitative full-field strain measurements by SAOED (SrAl2O4:Eu2+,Dy3+) mechanoluminescent materials

    Science.gov (United States)

    Imani Azad, Ali; Rahimi, Mohammad Reza; Yun, Gun Jin

    2016-09-01

    In this paper, a new calibration method for mechano-luminescence (ML) thin film sensors was proposed to enable quantitative full-field strain measurements in pixel-level resolution for the first time along with two standard reference test methods. The proposed method has a distinct advantage of its facet-free full-field strain sensing capability with pixel-level resolution. For the ML sensor, standard reference test methods were proposed for developing calibrated relationships between ML light intensity and effective strains: (1) uniaxial tensile reference test and (2) non-uniform strain reference test. From the reference tests, two different calibration models were developed in a recurrence equation form and validated measuring general strain distributions on different experimental specimens. Verified finite element (FE) simulation results were compared with ML effective strains to confirm its accuracy. The comparisons of the ML effective strains with FE simulation results showed that the calibration models can acceptably measure full-field strains. Limitations, sources of errors, suggestions for improving accuracy and practical considerations were also discussed. A conclusion of this research is that the proposed method enables ML sensing films to measure quantitative full-field strain distributions.

  19. Analysis of Modern Techniques for Nuclear-test Yield Determination of NTS Events Using Data From the Leo Brady Seismic Network

    Science.gov (United States)

    Schramm, K. A.; Bilek, S. L.; Abbott, R. E.

    2007-12-01

    Nuclear test detection is a challenging, but important task for treaty verification. Many techniques have been developed to discriminate between an explosion and an earthquake and if an explosion is detected, to determine its yield. Sandia National Laboratories (SNL) has maintained the Leo Brady Seismic Network (LBSN) since 1960 to record nuclear tests at the Nevada Test Site (NTS), providing a unique data set for yield determination. The LBSN is comprised of five permanent stations surrounding the NTS at regional distances, and data (in digital from post 1983) exists for almost all tests. Modern seismic data processing techniques can be used with this data to apply new methods to better determine the seismic yield. Using mb(Lg) we found that, when compared to published yields, our estimates were low for events over 100 kilotons (kt) and near the published value for events under 40 kt. We are currently measuring seismic-phase amplitudes, examining body- and surface-wave spectra and using seismic waveform modeling techniques to determine the seismic yield of NTS explosions using the waveforms from the LBSN.

  20. Complete data preparation flow for Massively Parallel E-Beam lithography on 28nm node full-field design

    Science.gov (United States)

    Fay, Aurélien; Browning, Clyde; Brandt, Pieter; Chartoire, Jacky; Bérard-Bergery, Sébastien; Hazart, Jérôme; Chagoya, Alexandre; Postnikov, Sergei; Saib, Mohamed; Lattard, Ludovic; Schavione, Patrick

    2016-03-01

    Massively parallel mask-less electron beam lithography (MP-EBL) offers a large intrinsic flexibility at a low cost of ownership in comparison to conventional optical lithography tools. This attractive direct-write technique needs a dedicated data preparation flow to correct both electronic and resist processes. Moreover, Data Prep has to be completed in a short enough time to preserve the flexibility advantage of MP-EBL. While the MP-EBL tools have currently entered an advanced stage of development, this paper will focus on the data preparation side of the work for specifically the MAPPER Lithography FLX-1200 tool [1]-[4], using the ASELTA Nanographics Inscale software. The complete flow as well as the methodology used to achieve a full-field layout data preparation, within an acceptable cycle time, will be presented. Layout used for Data Prep evaluation was one of a 28 nm technology node Metal1 chip with a field size of 26x33mm2, compatible with typical stepper/scanner field sizes and wafer stepping plans. Proximity Effect Correction (PEC) was applied to the entire field, which was then exported as a single file to MAPPER Lithography's machine format, containing fractured shapes and dose assignments. The Soft Edge beam to beam stitching method was employed in the specific overlap regions defined by the machine format as well. In addition to PEC, verification of the correction was included as part of the overall data preparation cycle time. This verification step was executed on the machine file format to ensure pattern fidelity and accuracy as late in the flow as possible. Verification over the full chip, involving billions of evaluation points, is performed both at nominal conditions and at Process Window corners in order to ensure proper exposure and process latitude. The complete MP-EBL data preparation flow was demonstrated for a 28 nm node Metal1 layout in 37 hours. The final verification step shows that the Edge Placement Error (EPE) is kept below 2.25 nm

  1. Breast Imaging Reporting and Data System (BI-RADS) breast composition descriptors: Automated measurement development for full field digital mammography

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, E. E.; Sellers, T. A.; Lu, B. [Department of Cancer Epidemiology, Division of Population Sciences, H. Lee Moffitt Cancer Center, Tampa, Florida 33612 (United States); Heine, J. J. [Department of Cancer Imaging and Metabolism, H. Lee Moffitt Cancer Center, Tampa, Florida 33612 (United States)

    2013-11-15

    Purpose: The Breast Imaging Reporting and Data System (BI-RADS) breast composition descriptors are used for standardized mammographic reporting and are assessed visually. This reporting is clinically relevant because breast composition can impact mammographic sensitivity and is a breast cancer risk factor. New techniques are presented and evaluated for generating automated BI-RADS breast composition descriptors using both raw and calibrated full field digital mammography (FFDM) image data.Methods: A matched case-control dataset with FFDM images was used to develop three automated measures for the BI-RADS breast composition descriptors. Histograms of each calibrated mammogram in the percent glandular (pg) representation were processed to create the new BR{sub pg} measure. Two previously validated measures of breast density derived from calibrated and raw mammograms were converted to the new BR{sub vc} and BR{sub vr} measures, respectively. These three measures were compared with the radiologist-reported BI-RADS compositions assessments from the patient records. The authors used two optimization strategies with differential evolution to create these measures: method-1 used breast cancer status; and method-2 matched the reported BI-RADS descriptors. Weighted kappa (κ) analysis was used to assess the agreement between the new measures and the reported measures. Each measure's association with breast cancer was evaluated with odds ratios (ORs) adjusted for body mass index, breast area, and menopausal status. ORs were estimated as per unit increase with 95% confidence intervals.Results: The three BI-RADS measures generated by method-1 had κ between 0.25–0.34. These measures were significantly associated with breast cancer status in the adjusted models: (a) OR = 1.87 (1.34, 2.59) for BR{sub pg}; (b) OR = 1.93 (1.36, 2.74) for BR{sub vc}; and (c) OR = 1.37 (1.05, 1.80) for BR{sub vr}. The measures generated by method-2 had κ between 0.42–0.45. Two of these

  2. Full field modeling of dynamic recrystallization in a global level set framework, application to 304L stainless steel

    Directory of Open Access Journals (Sweden)

    Boulais-Sinou Romain

    2016-01-01

    Full Text Available A new full field numerical approach for the simulation of dynamic and post-dynamic recrystallization will be detailed. A level Set framework is employed to link a crystal plasticity finite element method with the modeling of recrystallization. Plasticity is calculated through the activation of slip systems and provides predictions for both SSDs and GNDs densities. These predictions control the activation and kinetics of recrystallization. All the developments are applied on 304L stainless steel.

  3. Screen-film versus full-field digital mammography: Radiation dose and image quality in a large teaching hospital

    Directory of Open Access Journals (Sweden)

    Stantić Tomislav J.

    2013-01-01

    Full Text Available The objective of this paper is to measure the radiation dose and image quality in conventional screen-film mammography and full-field digital mammography in women referred to mammography examination. Participants underwent bilateral, two-view screen-film mammography or full-field digital mammography. The visibility of anatomical regions and overall clinical image quality was rated by experienced radiologists. Total of 387 women and 1548 mammograms were enrolled in the study. Image quality was assessed in terms of image quality score, whereas patient dose assessment was performed in terms of mean glandular dose. Average mean glandular dose for cranio-caudal projection was 1.5 mGy and 2.1 mGy in full-field digital mammography and screen-film mammography, respectively. For medio-lateral oblique projection, corresponding values were 2.3 and 2.1 mGy. Overall image quality criteria scoring was 0.82 and 0.99 for screen-film and digital systems, respectively. The scores were in the range from 0.11 to 1.0 for different anatomical structures. Overall, full-field digital mammography was superior both in terms of image quality and dose over the screen-film mammography. The results have indicated that phantom dose values can assist in setting the optimisation activities in mammography and for comparison between mammography units. To obtain accurate diagnostic information with an acceptable radiation dose to breast, it is necessary to periodically perform patient dose and image quality surveys in all mammography units.

  4. Full-field ultrasonic inspection for a composite sandwich plate skin-core debonding detection using laser-based ultrasonics

    Science.gov (United States)

    Chong, See Yenn; Victor, Jared J.; Todd, Michael D.

    2017-04-01

    In this paper, a full-field ultrasonic guided wave method is proposed to inspect a composite sandwich specimen made for an aircraft engine nacelle. The back skin/core interface of the specimen is built with two fabricated disbond defects (diameters of 12.7 mm and 25.4 mm) by removing areas of the adhesive used to bond the back skin to the core. A laser ultrasonic interrogation system (LUIS) incorporated with a disbond detection algorithm is developed. The system consists of a 1-kHz laser ultrasonic scanning system and a single fixed ultrasonic sensor to interrogate ultrasonic guided waves in the sandwich specimen. The interest area of 400 mm × 400 mm is scanned at a 0.5 mm scan interval. The corresponding full-field ultrasonic data is obtained and generated in the three-dimensional (3-D) space-time domain. Then, the 3-D full-field ultrasonic data is Fourier transformed and the ultrasonic frequency spectra are analyzed to determine the dominant frequency that is sensitive to the disbond defects. Continuous wavelet transform (CWT) based on fast Fourier transform (FFT) is implemented as a single-frequency bandpass filter to filter the full-field ultrasonic data in the 3-D space-time domain at the selected dominant frequency. The LUIS has shown the ability to detect the disbond with diameters of 11 mm and 23 mm which match to the pre-determined disbond sizes well. For future research, a robust signal processing algorithm and a model-based matched filter will be investigated to make the detection process autonomous and improve detectability

  5. Realization of the purely spatial Einstein-Podolsky-Rosen paradox in full-field images of spontaneous parametric down conversion

    CERN Document Server

    Moreau, Paul-Antoine; Devaux, Fabrice; Lantz, Eric

    2012-01-01

    We present a demonstration of EPR entanglement by detecting purely spatial quantum correlations in the near and far-field of highly spatially multimode spontaneous parametric down conversion generated in a type 2 BBO crystal. Full field imaging is performed in the photon counting regime with an electron-multiplying CCD (EMCCD) camera. We obtain a violation of Heisenberg inequalities with inferred quantities taking into account all the biphoton pairs in both the near and far field.

  6. Micro X-ray Fluorescence Imaging in a Tabletop Full Field-X-ray Fluorescence Instrument and in a Full Field-Particle Induced X-ray Emission End Station.

    Science.gov (United States)

    Romano, Francesco Paolo; Caliri, Claudia; Cosentino, Luigi; Gammino, Santo; Mascali, David; Pappalardo, Lighea; Rizzo, Francesca; Scharf, Oliver; Santos, Hellen Cristine

    2016-10-08

    A full field-X-ray camera (FF-XRC) was developed for performing the simultaneous mapping of chemical elements with a high lateral resolution. The device is based on a conventional CCD detector coupled to a straight shaped polycapillary. Samples are illuminated at once with a broad primary beam that can consist of X-rays or charged particles in two different analytical setups. The characteristic photons induced in the samples are guided by the polycapillary to the detector allowing the elemental imaging without the need for scanning. A single photon counting detection operated in a multiframe acquisition mode and a processing algorithm developed for event hitting reconstruction have enabled one to use the CCD as a high energy resolution X-ray detector. A novel software with a graphical user interface (GUI) programmed in Matlab allows full control of the device and the real-time imaging with a region-of-interest (ROI) method. At the end of the measurement, the software produces spectra for each of the pixels in the detector allowing the application of a least-squares fitting with external analytical tools. The FF-XRC is very compact and can be installed in different experimental setups. This work shows the potentialities of the instrument in both a full field-micro X-ray fluorescence (FF-MXRF) tabletop device and in a full field-micro particle induced X-ray emission (FF-MPIXE) end-station operated with an external proton beam. Some examples of applications are given as well.

  7. High-yield cultivation techniques of large-leaved water spinach(Ipomoea aquatica Forsk)%大叶空心菜高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    叶敏

    2015-01-01

    总结大叶空心菜高产栽培技术,主要包括播种育苗、定植、田间管理、病虫害防治、采收等方面内容。%High-yield cultivation techniques of large-leaved water spinach was summarized,mainly including culture of see-ding,field planting,field management,control of diseases and pests,harvesting and other aspects.

  8. Interactions of proteins with biogenic iron oxyhydroxides and a new culturing technique to increase biomass yields of neutrophilic, iron-oxidizing bacteria

    OpenAIRE

    Barco, Roman A.; Edwards, Katrina J

    2014-01-01

    Neutrophilic, bacterial iron-oxidation remains one of the least understood energy-generating biological reactions to date. One of the reasons it remains under-studied is because there are inherent problems with working with iron-oxidizing bacteria (FeOB), including low biomass yields and interference from the iron oxides in the samples. In an effort to circumvent the problem of low biomass, a new large batch culturing technique was developed. Protein interactions with biogenic iron oxides wer...

  9. A convenient method for experimental determination of yields and isomeric ratios in photonuclear reactions measured by the activation technique

    Science.gov (United States)

    Kolev, D.; Dobreva, E.; Nenov, N.; Todorov, V.

    1995-02-01

    A generalized exact formula is derived for a determination of the experimental isomeric ratio in any incident particle activation. For the particular case, when the activity of the ground state results from the simultaneous decay of both states and can be conveniently measured, the appropriate modification of this formula is evaluated and applied to six photonuclear reactions induced by 43 MeV bremsstrahlung. The experimental isomeric yield ratios of (γ, 3n) 110m,gIn; (γ, p) (γ, pn), (γ, 2n2p) 117m,gIn; (γ, n) 164m,gHo and (γ, 3n) 162m,gHo are deduced.

  10. Virus-free potato yield cultivation techniques%脱毒马铃薯高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    王拴福

    2012-01-01

      对马铃薯脱毒种薯的品种选择、地块选择、肥料使用、切块与消毒、播种、田间管理、病虫害防治及薯块收获等进行了研究。为提高脱毒马铃薯高产栽培提供了技术参考。%  potato virus-free seed variety selection, plot selection, fertilizer use, cuts and disinfection, planting, field management, pest control and tuber harvest. Provide a technical reference for Potato in high yield cultivation.

  11. Measurement of the mechanical properties of nickel film based on the full-field deformation:An improved blister method

    Institute of Scientific and Technical Information of China (English)

    Zihan Wang; Zengsheng Ma; Yichun Zhou; Chunsheng Lu

    2013-01-01

    To characterize the mechanical properties of thin films, an improved blister method is proposed, which combines a digital speckle correlation method with the blister test. Based on this method, an experimental setup is developed to measure Young's modulus, residual stress, and interfacial adhesion energy of an electroplated nickel film. The results show that the improved blister method has the advantage of a high accuracy full-field measurement with the simple operation and low requirement on environments, which can be used to characterize the mechanical properties of films with various scales from laboratorial to industrial applications.

  12. Full-field tracking and measuring of particle motion in capillary vessels by using time-varying laser speckle

    Science.gov (United States)

    Zhang, Luying; Wang, Bo; Wang, Yi

    2016-03-01

    We propose a random perturbation model to describe the variation of laser speckle patterns caused by moving particles in capillary vessels. When passing through probing volume, moving particles encode random perturbations into observed laser speckle patterns. We extract the perturbation envelopes of time-varying laser speckles for tracking the motion of single particle. And, the full-field transverse velocities of flowing particles are obtained by using cross-correlation between the perturbation envelopes. The proposed method is experimentally verified by the use of polymer-microsphere suspension in a glass capillary.

  13. Counting and differentiating aquatic biotic nanoparticles by full-field interferometry: from laboratory tests to Tara Oceans sample analysis

    CERN Document Server

    Boccara, Martine; Bryan, Catherine Venien; Bailly-Bechet, Marc; Bowler, Chris; Boccara, Albert Claude

    2016-01-01

    There is a huge abundance of viruses and membrane vesicles in seawater. We describe a new full-field, incoherently illuminated, shot-noise limited, common-path interferometric detection method that we couple with the analysis of Brownian motion to detect, quantify, and differentiate biotic nanoparticles. We validated the method with calibrated nanoparticles and homogeneous DNA or RNA.viruses. The smallest virus size that we characterized with a suitable signal-to-noise ratio was around 30 nm in diameter. Analysis of Brownian motions revealed anisotropic trajectories for myoviruses.We further applied the method for vesicles detection and for analysis of coastal and oligotrophic samples from Tara Oceans circumnavigation.

  14. Achromatic and high-resolution full-field X-ray microscopy based on total-reflection mirrors.

    Science.gov (United States)

    Matsuyama, Satoshi; Emi, Yoji; Kino, Hidetoshi; Kohmura, Yoshiki; Yabashi, Makina; Ishikawa, Tetsuya; Yamauchi, Kazuto

    2015-04-20

    We developed an achromatic and high-resolution full-field X-ray microscope based on advanced Kirkpatrick-Baez mirror optics that comprises two pairs of elliptical mirrors and hyperbolic mirrors utilizing the total reflection of X-rays. Performance tests to investigate the spatial resolution and chromatic aberration were performed at SPring-8. The microscope clearly resolved the pattern with ~100-nm feature size. Imaging the pattern by changing the X-ray energy revealed achromatism in the wide energy range of 8-11 keV.

  15. [Dissociation of visual evoked responses to hemi-field or full-field flash-checkerboard stimulation].

    Science.gov (United States)

    Samson-Dollfus, D; Layet, A; Hannequin, D; Menard, J F; Parain, D; Nehili, F

    1984-06-01

    Unexpected visual evoked responses (VERs) were recorded in 5 subjects with tumoral, ischemic or hemorrhagic lesions of the retrochiasmatic visual pathways. The flash pattern stimulation was always binocular and involved full-field and half-field stimuli. In these 5 cases, the total field VER was asymmetrical with anomalies on the affected occipital region. However half-field VERs P100 contralateral to the stimulus were noted both on the normal and on the affected occipital region. One can ask if this is not an electrophysiological equivalent of the clinical relative hemianopsia.

  16. 贵州高产油菜的群体结构特征及高产栽培技术%The Group Structure Characteristics and High-yield Culture Technique of High-yield Rape in Guizhou

    Institute of Scientific and Technical Information of China (English)

    冯文豪; 冯泽蔚; 苏跃

    2012-01-01

    In order to promote the integration and application of high yield cultivation technology of rape,the rape yield and component features in high-yield fields were analyzed in 2010-2011. The results showed that; 1) the group structure characteristics with the yield of over 200 kg/667m2 were as follows; average cultivation density 6 099. 2 plants/667m2 , mean pod number 3. 509 106 per 667 m2, grains per pod 18. 5, 1 000-seed weight 3. 7 g, plant height 191. 4 cm, branch number 10. 9, main inflorescence length 72. 8 cm, average yield 216. 2 kg/667m2. 2) The high-yield cultivation techniques included sowing in September 5-10, cultivating strong seedlings, transplanting on moderate-fertility soil in October 10 ?20, fine preparation of soil, soil testing and formulated fertilization, in time irrigation, disease, pest and grass control.%为了促进贵州油菜高产栽培技术的集成和运用,对2010-2011年参加贵州省油菜高产创建活动的高产田块油菜产量及其群体构成特征进行分析.结果表明:1)产量为200 kg/667m2以上油菜群体的结构特征为平均栽培密度达6 099.2株/667m2,平均角果数3.509×106个/667m2,每果粒数18.5粒,千粒重3.7g,株高191.4 cm,分枝数10.9个,主花序长72.8 cm,平均产量达216.2 kg/667m2.2)高产田块的栽培措施为9月5-10日播种,培育壮苗,10月10-20日移栽,土壤肥力中等,精细整地,测土配方施肥,及时灌排水和防治病虫草害等.

  17. Isotoxal star-shaped polygonal voids and rigid inclusions in nonuniform antiplane shear fields. Part I: Formulation and full-field solution

    CERN Document Server

    Corso, Francesco Dal; Bigoni, Davide

    2016-01-01

    An infinite class of nonuniform antiplane shear fields is considered for a linear elastic isotropic space and (non-intersecting) isotoxal star-shaped polygonal voids and rigid inclusions perturbing these fields are solved. Through the use of the complex potential technique together with the generalized binomial and the multinomial theorems, full-field closed-form solutions are obtained in the conformal plane. The particular (and important) cases of star-shaped cracks and rigid-line inclusions (stiffeners) are also derived. Except for special cases (addressed in Part II), the obtained solutions show singularities at the inclusion corners and at the crack and stiffener ends, where the stress blows-up to infinity, and is therefore detrimental to strength. It is for this reason that the closed-form determination of the stress field near a sharp inclusion or void is crucial for the design of ultra-resistant composites.

  18. Characterization of wet pad surface in chemical mechanical polishing (CMP) process with full-field optical coherence tomography (FF-OCT).

    Science.gov (United States)

    Choi, Woo June; Jung, Sung Pyo; Shin, Jun Geun; Yang, Danning; Lee, Byeong Ha

    2011-07-04

    Chemical mechanical polishing (CMP) is a key process for global planarization of silicon wafers for semiconductors and AlTiC wafers for magnetic heads. Removal rate of wafer material is directly dependent on the surface roughness of a CMP pad, thus the structure of the pad surface has been evaluated with variable techniques. However, under in situ CMP process, the measurements have been severely limited due to the existence of polishing fluids including the slurry on the pad surface. In here, we newly introduce ultra-high resolution full-field optical coherence tomography (FF-OCT) to investigate the surface of wet pads. With FF-OCT, the wet pad surface could be quantitatively characterized in terms of the polishing pad lifetime, and also be three-dimensionally visualized. We found that reasonable polishing span could be evaluated from the surface roughness measurement and the groove depth measurement made by FF-OCT.

  19. Measurement of high temperature full-field strain up to 2000 °C using digital image correlation

    Science.gov (United States)

    Wang, Wei; Xu, Chenghai; Jin, Hua; Meng, Songhe; Zhang, Yumin; Xie, Weihua

    2017-03-01

    Understanding the deformation and strain at elevated temperature is a critical factor for the stability of aerodynamic shape, and an important consideration for the thermal protection system design. However, accurate measurement of deformation and strain at high temperatures is a challenge. Here, we present a measurement study for full-field strain mapping up to 2000 °C using digital image correlation (DIC) method, which mainly depends on the quality of speckle patterns on the specimen surface. In our study, the strain values are analyzed by DIC method while specimens are heated using a large electric current. Improvements in filtering and speckling allow the measured temperatures using this method to reach 2000 °C. We confirmed the validity of this method by comparison of measured Young’s modulus values with reference data for Inconel 718 Ni-based superalloy and graphite at different temperatures. Additionally, the full-field strain and Young’s modulus were demonstrated for a carbon fiber-reinforced carbon (C/C) composite uniaxial tensile specimen at 2000 °C.

  20. A convenient method for experimental determination of yields and isomeric ratios in photonuclear reactions measured by the activation technique

    Energy Technology Data Exchange (ETDEWEB)

    Kolev, D. [Sofia Univ. (Bulgaria). Dept. of Physics; Dobreva, E. [Sofia Univ. (Bulgaria). Dept. of Physics; Nenov, N. [Sofia Univ. (Bulgaria). Dept. of Physics; Todorov, V. [A Higher Institute of Medicine, Sofia (Bulgaria)

    1995-03-15

    A generalized exact formula is derived for a determination of the experimental isomeric ratio in any incident particle activation. For the particular case, when the activity of the ground state results from the simultaneous decay of both states and can be conveniently measured, the appropriate modification of this formula is evaluated and applied to six photonuclear reactions induced by 43 MeV bremsstrahlung. The experimental isomeric yield ratios of ({gamma}, 3n) {sup 110m,g}In; ({gamma}, p) ({gamma}, pn), ({gamma}, 2n2p) {sup 117m,g}In; ({gamma}, n) {sup 164m,g}Ho and ({gamma}, 3n) {sup 162m,g}Ho are deduced. ((orig.)).

  1. The effect of hydrodistillation technique on the yield and composition of essential oil from the seed of petroselinum crispum (mill. Nym. Ex. A.W. Hill

    Directory of Open Access Journals (Sweden)

    Stanković Mihajlo Z.

    2004-01-01

    Full Text Available The essential oil was isolated from the seed of Petroselinum crispum (Mill. Nym. ex. A.W. Hill by using different techniques of Clevenger-type hydrodistillation. The highest yield of oil, after five consecutive hydrodistillation runs (3.9 mL/100 g of plant material, was obtained by the technique in which water from the still flask was separated by filtration and used together with fresh water for immersing the plant material in a subsequent distillation. Regardless of the technique used, the oil contained different amounts of α-pinene, ß-p/nene, limonene, 2,3,4,5-tetramethoxy-1-allylbenzene, apiole and 1,2-benzenedicarbonic acid.

  2. Can deficit irrigation techniques be used to enhance phosphorus and water use efficiency and benefit crop yields?

    Science.gov (United States)

    Wright, Hannah R.; Dodd, Ian C.; Blackwell, Martin S. A.; Surridge, Ben W. J.

    2015-04-01

    Soil drying and rewetting (DRW) affects the forms and availability of phosphorus (P). Water soluble P has been reported to increase 1.8- to 19-fold after air-drying with the majority of the increase (56-100%) attributable to organic P. Similarly, in two contrasting soil types DRW increased concentrations of total P and reactive P in leachate, likely due to enhanced P mineralisation and physiochemical processes causing detachment of soil colloids, with faster rewetting rates related to higher concentrations of P. The intensity of drying as well as the rate of rewetting influences organic and inorganic P cycling. How these dynamics are driven by soil water status, and impact crop P acquisition and growth, remains unclear. Improving P and water use efficiencies and crop yields is globally important as both P and water resources become increasingly scarce, whilst demand for food increases. Irrigation supply below the water requirement for full crop evapotranspiration is employed by agricultural practitioners where water supply is limited. Regulated deficit irrigation describes the scheduling of water supply to correspond to the times of highest crop demand. Alternate wetting and drying (AWD) is applied in lowland irrigated rice production to avoid flooding at certain times of crop development, and has benefited P nutrition and yields. This research aims to optimise the benefits of P availability and uptake achieved by DRW by guiding deficit irrigation management strategies. Further determination of underlying processes driving P cycling at fluctuating soil moisture status is required. Presented here is a summary of the literature on DRW effects on soil P availability and plant P uptake and partitioning, in a range of soil types and cropping systems, with emphasis on alternate wetting and drying irrigation (AWD) compared to continuous flooding in lowland irrigated rice production. Soil water contents and matric potentials, and effects on P dynamics, are highly variable

  3. Evaluation of Biomass Yield and Water Treatment in Two Aquaponic Systems Using the Dynamic Root Floating Technique (DRF)

    OpenAIRE

    Laura Silva; Eucario Gasca-Leyva; Edgardo Escalante; Kevin M Fitzsimmons; David Valdés Lozano

    2015-01-01

    The experiment evaluates the food production and water treatment of TAN, NO2−–N, NO3−–N, and PO43− in two aquaponics systems using the dynamic root floating technique (DRF). A separate recirculation aquaculture system (RAS) was used as a control. The fish cultured was Nile tilapia (Oreochromis niloticus). The hydroponic culture in one treatment (PAK) was pak choy (Brassica chinensis,) and in the other (COR) coriander (Coriandrum sativum). Initial and final weights were determined for the fis...

  4. Interactions of proteins with biogenic iron oxyhydroxides and a new culturing technique to increase biomass yields of neutrophilic, iron-oxidizing bacteria.

    Science.gov (United States)

    Barco, Roman A; Edwards, Katrina J

    2014-01-01

    Neutrophilic, bacterial iron-oxidation remains one of the least understood energy-generating biological reactions to date. One of the reasons it remains under-studied is because there are inherent problems with working with iron-oxidizing bacteria (FeOB), including low biomass yields and interference from the iron oxides in the samples. In an effort to circumvent the problem of low biomass, a new large batch culturing technique was developed. Protein interactions with biogenic iron oxides were investigated confirming that such interactions are strong. Therefore, a protein extraction method is described to minimize binding of proteins to biogenic iron oxides. The combination of these two methods results in protein yields that are appropriate for activity assays in gels and for proteomic profiling.

  5. Producing Technique of High Yield and Quality Pigment Marigold%高产优质色素万寿菊生产技术

    Institute of Scientific and Technical Information of China (English)

    张红

    2015-01-01

    For meeting the requirement of scale and industrialization production, it selected pigment marigold variety with high yield, high quality, and strong adverse resistance, summarized a set of scientific and complete producing techniques for marigold, and applied in practice, in order to realize stable and high yield for marigold in Faku area.%为适应规模化、工厂化生产的需要,优选出适合法库地区的高产、优质、抗逆性强的色素万寿菊品种,总结一整套科学、完善的万寿菊生产技术措施,并进行推广应用,以实现法库地区万寿菊的高产稳产.

  6. Reconstruction of Full-Field Wall Pressure Fluctuations on a Flat Plate in the Wake of a Step Cylinder: Applications of Linear Stochastic Estimation (LSE)

    Science.gov (United States)

    Peng, Di; Chen, Yujia; Wang, Shaofei; Liu, Yingzheng; Wang, Weizhe

    2016-11-01

    Previous studies have shown that it is possible to reconstruct the full flow field based on time-resolved measurements at discrete locations using linear stochastic estimation (LSE). The objective of this study is to develop and apply this technique to wall pressure fluctuation measurements in low speed flows. Time-resolved wall pressure fluctuations on a flat plate in the wake of a step cylinder at low speed (V PSP). The microphone arrays are arranged properly to capture the dominant features in the flow field at 10 kHz. The PSP is excited using a continuous UV-LED, and the luminescent signal is recorded by a high-speed camera at 2 kHz. The microphone data at discrete locations are used to reconstruct the full-field wall pressure fluctuations based on LSE. The PSP results serve as basis for improvement of the LSE scheme and also for validation of the reconstructed pressure field. Other data processing techniques including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) are also used for analyzing the unsteady flow features. This LSE technique has great potential in real-time flow diagnostics and control.

  7. Image stack alignment in full-field X-ray absorption spectroscopy using SIFT_PyOCL.

    Science.gov (United States)

    Paleo, Pierre; Pouyet, Emeline; Kieffer, Jérôme

    2014-03-01

    Full-field X-ray absorption spectroscopy experiments allow the acquisition of millions of spectra within minutes. However, the construction of the hyperspectral image requires an image alignment procedure with sub-pixel precision. While the image correlation algorithm has originally been used for image re-alignment using translations, the Scale Invariant Feature Transform (SIFT) algorithm (which is by design robust versus rotation, illumination change, translation and scaling) presents an additional advantage: the alignment can be limited to a region of interest of any arbitrary shape. In this context, a Python module, named SIFT_PyOCL, has been developed. It implements a parallel version of the SIFT algorithm in OpenCL, providing high-speed image registration and alignment both on processors and graphics cards. The performance of the algorithm allows online processing of large datasets.

  8. High yield cultivation techniques of cherry tomato in greenhouse%樱桃西红柿大棚高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    王道锋

    2015-01-01

    总结大棚樱桃西红柿高产栽培技术,主要包括品种选择、育苗、田块整理、大棚规格设置、定植、田间管理、病虫害防治、采收等方面内容。%This paper summarized high yield cultivation techniques of cherry tomato in greenhouse,including variety selec-tion,raising seedlings,field preparation,design of greenhouse size,field planting,field management,diseases and pests control,as well as harvest.

  9. 草莓地膜覆盖安全丰产栽培技术%Safe High-yielding Cultivation Technique of Film Mulching on Strawberry

    Institute of Scientific and Technical Information of China (English)

    刘爽; 李好琢

    2012-01-01

    Strawberry film mulching had the advantages of early maturing, high and stable yielding and high economic benefits. The effect of film mulching and safety cultivation technique were introduced. These would provided reference basis for the strawberry cultivation.%草莓地膜覆盖栽培具有早熟、高产、稳产、高收益等优点。该文主要介绍草莓地膜覆盖的作用和草莓地膜覆盖安全栽培技术规程,以期为草莓栽培提供参考依据。

  10. The High Yield Cultivation Techniques of Blueberry in Suitable Habitat of Anhui%安徽蓝莓适生地蓝莓丰产栽培技术

    Institute of Scientific and Technical Information of China (English)

    樊基胜; 蒋光月; 陶龙

    2012-01-01

    在安徽蓝莓适生地多年蓝莓栽培和管理基础上总结了蓝莓丰产栽培技术,从建园、管理到采收方面作了详细的描述,并阐述了病虫鸟害的防治.%The high yield cultivation techniques of blueberry in suitable habitat of Anhui based on years of cultivation and management were summarized. Moreover, the construction of orchard, field management and harvesting were described in detail, the prevention and cure of pest and disease damage were expounded.

  11. High-yielding cultivation techniques of ginger in the mountainous area of southern Fujian%闽南山区生姜高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    叶涌清

    2011-01-01

    闽南山区具有发展生姜生产的环境条件和发展空间,该文介绍了生姜生产对环境条件的要求,生姜各生长时期的管理要点及其高产栽培技术。%The mountainous area of southern Fujian possesses the environmental conditions and potential developing space for ginger production.This paper described the environmental requirement,key management points in different growth period and high-yielding cultivation techniques of ginger.

  12. High Yield Culture Technique of Summer Ipomoea batatas in Binhai County%滨海县夏山芋高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    李庆体; 金叶红; 迟金和; 李晴; 刘永

    2011-01-01

    从品质选择、育苗、地块选择、施肥、移栽、除草、病虫害防治、收获与贮藏等方面总结夏山芋高产栽培技术,以提高滨海县的山芋生产水平。%The high yield culture techniques of summer Ipomoea batatas were summarized from several aspects,such as variety selection,seeding,field selection,fertilization,transplantation,weeding,disease and insect control,harvesting and storage,so as to improve the production level of Ipomoea batatas in Binhai County.

  13. Method for the unique identification of hyperelastic material properties using full-field measures. Application to the passive myocardium material response.

    Science.gov (United States)

    Perotti, Luigi E; Ponnaluri, Aditya V S; Krishnamoorthi, Shankarjee; Balzani, Daniel; Ennis, Daniel B; Klug, William S

    2017-01-18

    Quantitative measurement of the material properties (eg, stiffness) of biological tissues is poised to become a powerful diagnostic tool. There are currently several methods in the literature to estimating material stiffness, and we extend this work by formulating a framework that leads to uniquely identified material properties. We design an approach to work with full-field displacement data-ie, we assume the displacement field due to the applied forces is known both on the boundaries and also within the interior of the body of interest-and seek stiffness parameters that lead to balanced internal and external forces in a model. For in vivo applications, the displacement data can be acquired clinically using magnetic resonance imaging while the forces may be computed from pressure measurements, eg, through catheterization. We outline a set of conditions under which the least-square force error objective function is convex, yielding uniquely identified material properties. An important component of our framework is a new numerical strategy to formulate polyconvex material energy laws that are linear in the material properties and provide one optimal description of the available experimental data. An outcome of our approach is the analysis of the reliability of the identified material properties, even for material laws that do not admit unique property identification. Lastly, we evaluate our approach using passive myocardium experimental data at the material point and show its application to identifying myocardial stiffness with an in silico experiment modeling the passive filling of the left ventricle. Copyright © 2017 John Wiley & Sons, Ltd.

  14. High.yield cultivation technique for "Jingtian" No. 1 melon%景甜一号甜瓜高产高效栽培技术

    Institute of Scientific and Technical Information of China (English)

    朱团威

    2011-01-01

    Melon cultivation has a long history, but the problems of species simplification, extensive management, low yields, poor economic benefit, etc, are still existed. By means of introducing new varieties and assorted cultivation and management techniques to achieve high yield and high cost-effectiveness is an urgent need for melon production. A new varieties of sweet melon, "Jingtian" No. 1 melon, yields up to 3 000- 3 500kg per 667 m2, 1 000-1 500kg higher than the common varieties, has a good promotion prospect.%藤县种植甜瓜有悠久的历史,但存在品种单一,管理粗放,产量低,经济效益差等突出问题。引进甜瓜新品种及其配套栽培管理技术,达到高产高效是甜瓜生产的迫切需要。甜瓜新品种景甜一号采用科学的栽培管理技术进行栽培管理,可获得高产高效,每667m2产量达3 000~3 500kg,比一般品种每667m2增收1 000~1 500kg。

  15. Comparison of full field and anomaly initialisation for decadal climate prediction: towards an optimal consistency between the ocean and sea-ice anomaly initialisation state

    Science.gov (United States)

    Volpi, Danila; Guemas, Virginie; Doblas-Reyes, Francisco J.

    2017-08-01

    Decadal prediction exploits sources of predictability from both the internal variability through the initialisation of the climate model from observational estimates, and the external radiative forcings. When a model is initialised with the observed state at the initial time step (Full Field Initialisation—FFI), the forecast run drifts towards the biased model climate. Distinguishing between the climate signal to be predicted and the model drift is a challenging task, because the application of a-posteriori bias correction has the risk of removing part of the variability signal. The anomaly initialisation (AI) technique aims at addressing the drift issue by answering the following question: if the model is allowed to start close to its own attractor (i.e. its biased world), but the phase of the simulated variability is constrained toward the contemporaneous observed one at the initialisation time, does the prediction skill improve? The relative merits of the FFI and AI techniques applied respectively to the ocean component and the ocean and sea ice components simultaneously in the EC-Earth global coupled model are assessed. For both strategies the initialised hindcasts show better skill than historical simulations for the ocean heat content and AMOC along the first two forecast years, for sea ice and PDO along the first forecast year, while for AMO the improvements are statistically significant for the first two forecast years. The AI in the ocean and sea ice components significantly improves the skill of the Arctic sea surface temperature over the FFI.

  16. Comparison of full field and anomaly initialisation for decadal climate prediction: towards an optimal consistency between the ocean and sea-ice anomaly initialisation state

    Science.gov (United States)

    Volpi, Danila; Guemas, Virginie; Doblas-Reyes, Francisco J.

    2016-10-01

    Decadal prediction exploits sources of predictability from both the internal variability through the initialisation of the climate model from observational estimates, and the external radiative forcings. When a model is initialised with the observed state at the initial time step (Full Field Initialisation—FFI), the forecast run drifts towards the biased model climate. Distinguishing between the climate signal to be predicted and the model drift is a challenging task, because the application of a-posteriori bias correction has the risk of removing part of the variability signal. The anomaly initialisation (AI) technique aims at addressing the drift issue by answering the following question: if the model is allowed to start close to its own attractor (i.e. its biased world), but the phase of the simulated variability is constrained toward the contemporaneous observed one at the initialisation time, does the prediction skill improve? The relative merits of the FFI and AI techniques applied respectively to the ocean component and the ocean and sea ice components simultaneously in the EC-Earth global coupled model are assessed. For both strategies the initialised hindcasts show better skill than historical simulations for the ocean heat content and AMOC along the first two forecast years, for sea ice and PDO along the first forecast year, while for AMO the improvements are statistically significant for the first two forecast years. The AI in the ocean and sea ice components significantly improves the skill of the Arctic sea surface temperature over the FFI.

  17. Full-field wing deformation measurement scheme for in-flight cantilever monoplane based on 3D digital image correlation

    Science.gov (United States)

    Li, Lei-Gang; Liang, Jin; Guo, Xiang; Guo, Cheng; Hu, Hao; Tang, Zheng-Zong

    2014-06-01

    In this paper, a new non-contact scheme, based on 3D digital image correlation technology, is presented to measure the full-field wing deformation of in-flight cantilever monoplanes. Because of the special structure of the cantilever wing, two conjugated camera groups, which are rigidly connected and calibrated to an ensemble respectively, are installed onto the vertical fin of the aircraft and record the whole measurement. First, a type of pre-stretched target and speckle pattern are designed to adapt the oblique camera view for accurate detection and correlation. Then, because the measurement cameras are swinging with the aircraft vertical trail all the time, a camera position self-correction method (using control targets sprayed on the back of the aircraft), is designed to orientate all the cameras’ exterior parameters to a unified coordinate system in real time. Besides, for the excessively inclined camera axis and the vertical camera arrangement, a weak correlation between the high position image and low position image occurs. In this paper, a new dual-temporal efficient matching method, combining the principle of seed point spreading, is proposed to achieve the matching of weak correlated images. A novel system is developed and a simulation test in the laboratory was carried out to verify the proposed scheme.

  18. Full-field bulge test for planar anisotropic tissues: part I--experimental methods applied to human skin tissue.

    Science.gov (United States)

    Tonge, Theresa K; Atlan, Lorre S; Voo, Liming M; Nguyen, Thao D

    2013-04-01

    The nonlinear anisotropic properties of human skin tissue were investigated using bulge testing. Full-field displacement data were obtained during testing of human skin tissues procured from the lower back of post-mortem human subjects using 3-D digital image correlation. To measure anisotropy, the dominant fiber direction of the tissue was determined from the deformed geometry of the specimen. Local strains and stress resultants were calculated along both the dominant fiber direction and the perpendicular direction. Variation in anisotropy and stiffness was observed between specimens. The use of stress resultants rather than the membrane stress approximation accounted for bending effects, which are significant for a thick nonlinear tissue. Of the six specimens tested, it was observed that specimens from older donors exhibited a stiffer and more isotropic response than those from younger donors. It was seen that the mechanical response of the tissue was negligibly impacted by preconditioning or the ambient humidity. The methods presented in this work for skin tissue are sufficiently general to be applied to other planar tissues, such as pericardium, gastrointestinal tissue, and fetal membranes. The stress resultant-stretch relations will be used in a companion paper to obtain material parameters for a nonlinear anisotropic hyperelastic model. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  19. Super-resolved image acquisition with full-field localization-based microscopy: theoretical analysis and evaluation

    Science.gov (United States)

    Son, Taehwang; Lee, Wonju; Kim, Donghyun

    2016-02-01

    We analyze and evaluate super-resolved image acquisition with full-field localization microscopy in which an individual signal sampled by localization may or may not be switched. For the analysis, Nyquist-Shannon sampling theorem based on ideal delta function was extended to sampling with unit pulse comb and surface-enhanced localized near-field that was numerically calculated with finite difference time domain. Sampling with unit pulse was investigated in Fourier domain where magnitude of baseband becomes larger than that of adjacent subband, i.e. aliasing effect is reduced owing to pulse width. Standard Lena image was employed as imaging target and a diffraction-limited optical system is assumed. A peak signal-to-noise ratio (PSNR) was introduced to evaluate the efficiency of image reconstruction quantitatively. When the target was sampled without switching by unit pulse as the sampling width and period are varied, PSNR increased eventually to 18.1 dB, which is the PSNR of a conventional diffraction-limited image. PSNR was found to increase with a longer pulse width due to reduced aliasing effect. When switching of individual sampling pulses was applied, blurry artifact outside the excited field is removed for each pulse and PSNR soars to 25.6 dB with a shortened pulse period, i.e. effective resolution of 72 nm is obtained, which can further be decreased.

  20. A full-field strategy to take texture-induced anisotropy into account during FE simulations of metal forming processes

    Science.gov (United States)

    van Houtte, Paul; Gawad, Jerzy; Eyckens, Philip; van Bael, Bert; Samaey, Giovanni; Roose, Dirk

    2011-11-01

    During metal forming, the mechanical properties in all locations of the part evolve, usually in a heterogeneous way. In principle, this should be taken into account when performing finite element (FE) simulations of the forming process, by modeling the evolution of the mechanical properties in every integration point of the FE mesh and coupling the result back to the FEshell. This is the meaning of the term `full-field modeling.' The issue is developed further with focus on the evolution of texture and plastic anisotropy. It is explained that in principle, such fullfield modeling would require a gigantic computational effort which (at least at present) would be out of reach of most research organizations. A methodology is then presented to overcome this difficulty by using efficient models for texture updating and for texture-based plastic anisotropy, and by optimizing the overall calculation scheme without sacrificing the accuracy of the texture prediction. Some of the first results (obtained for cup drawing of anisotropic deep drawing steel) are shown, including comparison to experimental results. Possible future applications of the method are proposed.

  1. Full-field dynamic strain prediction on a wind turbine using displacements of optical targets measured by stereophotogrammetry

    Science.gov (United States)

    Baqersad, Javad; Niezrecki, Christopher; Avitabile, Peter

    2015-10-01

    Health monitoring of rotating structures (e.g. wind turbines and helicopter blades) has historically been a challenge due to sensing and data transmission problems. Unfortunately mechanical failure in many structures initiates at components on or inside the structure where there is no sensor located to predict the failure. In this paper, a wind turbine was mounted with a semi-built-in configuration and was excited using a mechanical shaker. A series of optical targets was distributed along the blades and the fixture and the displacement of those targets during excitation was measured using a pair of high speed cameras. Measured displacements with three dimensional point tracking were transformed to all finite element degrees of freedom using a modal expansion algorithm. The expanded displacements were applied to the finite element model to predict the full-field dynamic strain on the surface of the structure as well as within the interior points. To validate the methodology of dynamic strain prediction, the predicted strain was compared to measured strain by using six mounted strain-gages. To verify if a simpler model of the turbine can be used for the expansion, the expansion process was performed both by using the modes of the entire turbine and modes of a single cantilever blade. The results indicate that the expansion approach can accurately predict the strain throughout the turbine blades from displacements measured by using stereophotogrammetry.

  2. Combined use of fine needle aspiration cytology and full field digital mammography in preoperative assessment of breast masses

    Institute of Scientific and Technical Information of China (English)

    Yanan Zhang; Junsheng Li; Zhenling Ji; Wenhao Tang

    2008-01-01

    Objective: To evaluate the accuracy of these two methods and focus on the analysis and management of the false-negative cases.Methods: Results of full field digital mammography (FFDM) and fine needle aspiration cytology (FNAC)were obtained and analyzed from a consecutive of 102 women with palpable breast masses, results were correlated with the histopathological findings.Results: Of the 102 cases, malignancy was confirmed in 43 cases (42.16%) by final pathological examination, the sensitivity and specificity of cancer detection with FNA cytology was 90.7% (39/43) and 89.8% (53/59), respectively, the whole accuracy was 90.2% (92/102), with a positive predictive value of 86.7% (39/45) and a negative predictive value of 93.0% (53/57).FFDM gave a sensitivity of 88.4% (38/43), specificity of 83.1% (49/59), and whole accuracy 85.3% (87/102), the positive predictive value and negative predictive value was 79.2% (38/48) and 90.7% (49/54), respectively.All the FNAC-negative cancer cases were suggestive of malignancy by FFDM findings, however, the benign cases which presentas equivocal finding by FNA cytology, could not be ruled out the presence of malignancy.Conclusion: FNAC and FFDM both are accurate, effective and economical diagnostic modalities, combined use of these two methods can reduced the misdiagnosis rate of breast masses.

  3. A full-field transmission x-ray microscope for time-resolved imaging of magnetic nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Ewald, J.; Nisius, T.; Abbati, G.; Baumbach, S.; Overbuschmann, J.; Wilhein, T. [Institute for X-Optics (IXO), Hochschule Koblenz, Joseph-Rovan-Allee 2, 53424 Remagen (Germany); Wessels, P.; Wieland, M.; Drescher, M. [The Hamburg Centre for Ultrafast Imaging (CUI), University of Hamburg, Luruper Chaussee 149, 22761 Hamburg (Germany); Institut für Experimentalphysik, University of Hamburg, Luruper Chaussee 149, 22761 Hamburg (Germany); Vogel, A. [Institut für Angewandte Physik, University of Hamburg, Jungiusstraße 11, 20355 Hamburg (Germany); Viefhaus, J. [Deutsches Elektronen-Synchrotron (DESY), Notkestraße 85, 22607 Hamburg (Germany); Meier, G. [The Hamburg Centre for Ultrafast Imaging (CUI), University of Hamburg, Luruper Chaussee 149, 22761 Hamburg (Germany); Max Planck Institute for the Structure and Dynamics of Matter, Luruper Chaussee 149, 22761 Hamburg (Germany)

    2016-01-28

    Sub-nanosecond magnetization dynamics of small permalloy (Ni{sub 80}Fe{sub 20}) elements has been investigated with a new full-field transmission microscope at the soft X-ray beamline P04 of the high brilliance synchrotron radiation source PETRA III. The soft X-ray microscope generates a flat-top illumination field of 20 μm diameter using a grating condenser. A tilted nanostructured magnetic sample can be excited by a picosecond electric current pulse via a coplanar waveguide. The transmitted light of the sample plane is directly imaged by a micro zone plate with < 65 nm resolution onto a 2D gateable X-ray detector to select one particular bunch in the storage ring that probes the time evolution of the dynamic information successively via XMCD spectromicroscopy in a pump-probe scheme. In the experiments it was possible to generate a homogeneously magnetized state in patterned magnetic layers by a strong magnetic Oersted field pulse of 200 ps duration and directly observe the recovery to the initial flux-closure vortex patterns.

  4. Time-Lapse Observation of Electrolysis of Copper Sulfate with a Full-Field X-ray Fluorescence Imaging Microscope

    Science.gov (United States)

    Ohigashi, Takuji; Aota, Tatsuya; Watanabe, Norio; Takano, Hidekazu; Yokosuka, Hiroki; Aoki, Sadao

    2008-06-01

    The time-lapse observation of the electrodeposition of copper in copper sulfate solution was performed by imaging X-ray fluorescence from the copper deposition. The X-ray fluorescence was directly imaged with a full-field Wolter mirror microscope, which was constructed at the Photon Factory. Controlling the electric current in the solution from 0 to 71.7 µA, the deposition of copper on a Pt cathode was directly observed by imaging its X-ray fluorescence. One exposure time for obtaining an X-ray fluorescence image was 80 s. Then, it was 17 min later from the beginning of the electrolysis when the X-ray fluorescence image of the electrodeposition is observed for the first time. At this exposure time, the detection limit of the mass of copper was estimated to be 0.60 pg/image, which was calculated using test samples of 1.00×10-3-1.00 mol/l copper sulfate solutions.

  5. Rapid and high-resolution imaging of human liver specimens by full-field optical coherence tomography

    Science.gov (United States)

    Zhu, Yue; Gao, Wanrong; Zhou, Yuan; Guo, Yingcheng; Guo, Feng; He, Yong

    2015-11-01

    We report rapid and high-resolution tomographic en face imaging of human liver specimens by full-field optical coherence tomography (FF-OCT). First, the arrangement of the FF-OCT system was described and the performance of the system was measured. The measured axial and lateral resolutions of the system are 0.8 and 0.9 μm, respectively. The system has a sensitivity of ˜60 dB and can achieve an imaging rate of 7 fps and a penetration depth of ˜80 μm. The histological structures of normal liver can be seen clearly in the en face tomographic images, including central veins, cords of hepatocytes separated by sinusoidal spaces, and portal area (portal vein, the hepatic arteriole, and the bile duct). A wide variety of histological subtypes of hepatocellular carcinoma was observed in en face tomographic images, revealing notable cancerous features, including the nuclear atypia (enlarged convoluted nuclei), the polygonal tumor cells with obvious resemblance to hepatocytes with enlarged nuclei. In addition, thicker fibrous bands, which make the cytoplasmic plump vesicular nuclei indistinct, were also seen in the images. Finally, comparison between the portal vein in a normal specimen versus that seen in the rare type of cholangiocarcinoma was made. The results show that the cholangiocarcinoma presents with a blurred pattern of portal vein in the lateral direction and an aggregated distribution in the axial direction; the surrounding sinusoidal spaces and nuclei of cholangiocarcinoma are absent. The findings in this work may be used as additional signs of liver cancer or cholangiocarcinoma, demonstrating capacity of FF-OCT device for early cancer diagnosis and many other tumor-related studies in biopsy.

  6. Performance of computer-aided detection applied to full-field digital mammography in detection of breast cancers

    Energy Technology Data Exchange (ETDEWEB)

    Sadaf, Arifa, E-mail: arifa.sadaf@gmail.com [Department of Medical Imaging, Mount Sinai Hospital, Toronto, Ontario, M5G 1X5 (Canada); Crystal, Pavel, E-mail: pavel.crystal@utoronto.ca [Department of Medical Imaging, Mount Sinai Hospital, Toronto, Ontario, M5G 1X5 (Canada); Scaranelo, Anabel, E-mail: anabel.scaranelo@uhn.on.ca [Department of Medical Imaging, Princess Margaret Hospital, 610 University Avenue, Rm 3-922, Toronto, Ontario, M5G 2M9 (Canada); Helbich, Thomas, E-mail: thomas.helbich@meduniwien.ac.at [Medical University Vienna - General Hospital Vienna, Waehringer Guertel 18-20, Floor 7F, 1090 Vienna (Austria)

    2011-03-15

    Objective: The aim of this retrospective study was to evaluate performance of computer-aided detection (CAD) with full-field digital mammography (FFDM) in detection of breast cancers. Materials and Methods: CAD was retrospectively applied to standard mammographic views of 127 cases with biopsy proven breast cancers detected with FFDM (Senographe 2000, GE Medical Systems). CAD sensitivity was assessed in total group of 127 cases and for subgroups based on breast density, mammographic lesion type, mammographic lesion size, histopathology and mode of presentation. Results: Overall CAD sensitivity was 91% (115 of 127 cases). There were no statistical differences (p > 0.1) in CAD detection of cancers in dense breasts 90% (53/59) versus non-dense breasts 91% (62/68). There was statistical difference (p < 0.05) in CAD detection of cancers that appeared mammographically as microcalcifications only versus other mammographic manifestations. CAD detected 100% (44/44) of cancers manifesting as microcalcifications, 89% (47/53) as no-calcified masses or asymmetries, 88% (14/16) as masses with associated calcifications, and 71% (10/14) as architectural distortions. CAD sensitivity for cancers 1-10 mm was 84% (38/45); 11-20 mm 93% (55/59); and >20 mm 97% (22/23). Conclusion: CAD applied to FFDM showed 100% sensitivity in identifying cancers manifesting as microcalcifications only and high sensitivity 86% (71/83) for other mammographic appearances of cancer. Sensitivity is influenced by lesion size. CAD in FFDM is an adjunct helping radiologist in early detection of breast cancers.

  7. Mapping 3D breast lesions from full-field digital mammograms using subject-specific finite element models

    Science.gov (United States)

    García, E.; Oliver, A.; Diaz, O.; Diez, Y.; Gubern-Mérida, A.; Martí, R.; Martí, J.

    2017-03-01

    Patient-specific finite element (FE) models of the breast have received increasing attention due to the potential capability of fusing images from different modalities. During the Magnetic Resonance Imaging (MRI) to X-ray mammography registration procedure, the FE model is compressed mimicking the mammographic acquisition. Subsequently, suspicious lesions in the MRI volume can be projected into the 2D mammographic space. However, most registration algorithms do not provide the reverse information, avoiding to obtain the 3D geometrical information from the lesions localized in the mammograms. In this work we introduce a fast method to localize the 3D position of the lesion within the MRI, using both cranio-caudal (CC) and medio-lateral oblique (MLO) mammographic projections, indexing the tetrahedral elements of the biomechanical model by means of an uniform grid. For each marked lesion in the Full-Field Digital Mammogram (FFDM), the X-ray path from source to the marker is calculated. Barycentric coordinates are computed in the tetrahedrons traversed by the ray. The list of elements and coordinates allows to localize two curves within the MRI and the closest point between both curves is taken as the 3D position of the lesion. The registration errors obtained in the mammographic space are 9.89 +/- 3.72 mm in CC- and 8.04 +/- 4.68 mm in MLO-projection and the error in the 3D MRI space is equal to 10.29 +/- 3.99 mm. Regarding the uniform grid, it is computed spending between 0.1 and 0.7 seconds. The average time spent to compute the 3D location of a lesion is about 8 ms.

  8. Microcalcification detection in full-field digital mammograms with PFCM clustering and weighted SVM-based method

    Science.gov (United States)

    Liu, Xiaoming; Mei, Ming; Liu, Jun; Hu, Wei

    2015-12-01

    Clustered microcalcifications (MCs) in mammograms are an important early sign of breast cancer in women. Their accurate detection is important in computer-aided detection (CADe). In this paper, we integrated the possibilistic fuzzy c-means (PFCM) clustering algorithm and weighted support vector machine (WSVM) for the detection of MC clusters in full-field digital mammograms (FFDM). For each image, suspicious MC regions are extracted with region growing and active contour segmentation. Then geometry and texture features are extracted for each suspicious MC, a mutual information-based supervised criterion is used to select important features, and PFCM is applied to cluster the samples into two clusters. Weights of the samples are calculated based on possibilities and typicality values from the PFCM, and the ground truth labels. A weighted nonlinear SVM is trained. During the test process, when an unknown image is presented, suspicious regions are located with the segmentation step, selected features are extracted, and the suspicious MC regions are classified as containing MC or not by the trained weighted nonlinear SVM. Finally, the MC regions are analyzed with spatial information to locate MC clusters. The proposed method is evaluated using a database of 410 clinical mammograms and compared with a standard unweighted support vector machine (SVM) classifier. The detection performance is evaluated using response receiver operating (ROC) curves and free-response receiver operating characteristic (FROC) curves. The proposed method obtained an area under the ROC curve of 0.8676, while the standard SVM obtained an area of 0.8268 for MC detection. For MC cluster detection, the proposed method obtained a high sensitivity of 92 % with a false-positive rate of 2.3 clusters/image, and it is also better than standard SVM with 4.7 false-positive clusters/image at the same sensitivity.

  9. Understanding three-dimensional spatial relationship between the mouse second polar body and first cleavage plane with full-field optical coherence tomography.

    Science.gov (United States)

    Zheng, Jing-gao; Huo, Tiancheng; Chen, Tianyuan; Wang, Chengming; Zhang, Ning; Tian, Ning; Zhao, Fengying; Lu, Danyu; Chen, Dieyan; Ma, Wanyun; Sun, Jia-lin; Xue, Ping

    2013-01-01

    The morphogenetic relationship between early patterning and polarity formation is of fundamental interest and remains a controversial issue in preimplantation embryonic development. We use a label-free three-dimensional (3-D) imaging technique of full-field optical coherence tomography (FF-OCT) successfully for the first time to study the dynamics of developmental processes in mouse preimplantation lives. Label-free 3-D subcellular time-lapse images are demonstrated to investigate 3-D spatial relationship between the second polar body (2PB) and the first cleavage plane. By using FF-OCT together with quantitative study, we show that only 25% of the predicted first cleavage planes, defined by the apposing plane of two pronuclei, pass through the 2PB. Also only 27% of the real cleavage planes pass through the 2PB. These results suggest that the 2PB is not a convincing spatial cue for the event of the first cleavage. Our studies demonstrate the feasibility of FF-OCT in providing new insights and potential breakthroughs to the controversial issues of early patterning and polarity in mammalian developmental biology.

  10. 蕉芋优质高产栽培技术%High quality and high-yielding cultivation techniques of edible canna(Canna edulis)

    Institute of Scientific and Technical Information of China (English)

    刘恒

    2012-01-01

    蕉芋的市场发展前景广阔。该文从品种选择、土壤选择、耕翻整地、幼苗繁殖、适时定植、田间管理、水分管理、病虫害防治、采收与加工等方面介绍蕉芋的优质高产栽培技术。%Edible canna has good market potential.This paper introduced high quality and high-yielding cultivation techniques of edible canna,including cultivar selection,soil selection,ploughing and soil preparation,seedling propagation,planting in suitable time,field management,water management,control of diseases and pests,harvest and processing.

  11. 早春大棚番茄高产栽培技术探讨%Discussion on Yield Cultivation Techniques of Early Spring Tomato in Greenhouse

    Institute of Scientific and Technical Information of China (English)

    颜耀东

    2014-01-01

    Starting from the variety selection ,the yield cultivation techniques of early spring tomato in greenhouse were elaborated from the following aspects, including preparation before planting, planting, seedling management, flowering stage management, pest controlling and others. The results provided technical references for tomato production.%从品种选择出发,阐述了早春大棚番茄高产栽培技术,包括定植前准备、定植、苗期管理、开花结果期管理及病虫害防治等方面,为番茄生产提供了技术借鉴。

  12. 豫东平原夏玉米高产栽培技术%High Yield Cultivation Techniques of Summer Maize in the Plain Area of Eastern Henan

    Institute of Scientific and Technical Information of China (English)

    张永阁

    2015-01-01

    High yield cultivation techniques of summer maize in the plain area of Eastern Henan were summarized from species selection,sowing,thinning and spacing,fertilizer and water management,control of pest and disease and grass,harvest late at the appropriate time etc,so as to promote the cultivation of summer maize at the local.%从品种选择、播种、间苗定苗、肥水管理、病虫草害防治、适期晚收等方面总结了豫东平原夏玉米高产栽培技术,以促进当地夏玉米的高产栽培。

  13. Discussion on High Yield Cultivation Techniques of Summer Corn without Tillage%夏玉米免耕高产高效栽培技术探讨

    Institute of Scientific and Technical Information of China (English)

    王超; 王为联; 余福州

    2014-01-01

    从介绍夏玉米免耕机械直播的优点出发,阐述了夏玉米免耕高产高效栽培技术,包括麦茬处理、选用品种及种子处理、播种及田间管理等方面,为夏玉米生产提供了技术参考。%Starting from introducing the advantages of machinery direct seeding summer corn without tillage, the high yield cultivation techniques of summer corn without tillage were elaborated from the following aspects, including stubble treatment, the choice of varieties and seed treatment, planting and field management, etc. The results provided technical references for summer corn production.

  14. High-yield Cultivation Techniques of Green Corn in Weishan County%巍山县青玉米高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    谢增纲

    2014-01-01

    介绍巍山县青玉米的高产栽培技术,包括选种及种子处理、选地与整地、播种覆膜、田间管理及病虫草害防治等,以期为该县青玉米的发展提供参考。%High-yield cultivation techniques of green corn in Weishan County were introduced,including seed selection and treatment,selection and preparation of ground,seeding mulching,field management,pest and disease and grass control etc.,so as to provide reference for the development of green corn in Weishan County.

  15. 东塘水蜜桃高产优质栽培技术%High yield and quality cultivation techniques for honey peach in Dongtang

    Institute of Scientific and Technical Information of China (English)

    陈华勤

    2015-01-01

    Biological characteristics of Dongtang honey peach were observed,and the high yield and quality cultivation tech-nique was summarized,which included garden construction planning,scientific cultivation,reasonable pruning,establishing healthy tree crown,scientific fertilization,improving quality,and pests and diseases control.%通过对东塘水蜜桃生物学性状进行观察,总结其高产优质栽培技术:规划建园,科学种植;合理整枝修剪,培养良好树冠;科学施肥,提高品质;科学防治病虫害。

  16. High Yield Cultivation Techniques of Cherry Tomato in Guangxi%广西樱桃番茄高产栽培技术探讨

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    Cherry tomatoes were the leading industry in Tianyang of Guangxi. The high yield cultivation techniques were summarized from the following aspects , including varieties selection, breeding strong seedlings, intensive cultivation and strengthening base fertilizers, timely planting, scientific field management, making frames for the climbing, pollination, control of diseases and pests, and so on. The results provided technical information for production of cherry tomatoes.%樱桃番茄是广西田阳的主导产业。从品种选择、培育壮苗、精耕细作、重施基肥、定植、田间水肥管理、及时插杆整枝、点花授粉及病虫害防治等几个方面总结了樱桃番茄超高产栽培技术,为生产提供了技术参考。

  17. Pollution-free and high-yielding cultivation techniques of edamame bean%毛豆高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    刘必胜

    2012-01-01

    This paper introduced characteristics and environmental requirement of edamame bean.Some high-yielding cultivation techniques,including field selection,soil preparation,seed pretreatment,scientific topdressing,hilling in the intertillage operation,irrigation and drainage and control of diseases and pests were summarized.%介绍毛豆品种特征特性及毛豆生长对环境条件的要求,从地块选择、整地、种子处理、播种、科学追肥、中耕培土、灌溉排水、病虫害防治等方面总结了毛豆的高产栽培技术。

  18. 早稻高产施肥关键技术综述%Key Fertilization Techniques for High Yield of Early Rice

    Institute of Scientific and Technical Information of China (English)

    陈蔚; 谢保忠; 王万福; 张绍安; 余保生

    2011-01-01

    The key fertilization techniques for high yield of early rice, including scientific application of seedling fertilizers, cultivating strong seedling, use of appropriate principles of field fertilization patterns and fertilizer, enough field basal, early application of tillering fertilizer, skillfully applicating of panicle fertilizer according to plants. And the effect of each application of fertilizer on early rice growth and yield components of early rice was analyzed to guide rational fertilization.%阐述了早稻高产施肥的关键技术,包括秧田科学施肥,培育壮秧,采用适宜的大田施肥模式和施肥原则,施足大田基肥,早施分蘖肥,看苗巧施穗粒肥等;并分析了各次施肥对早稻生长发育和产量构成因素的作用,以期指导早稻的合理施肥.

  19. High Yield Cultivation Techniques of Density-tolerant Spring Maize in Northern China%北方耐密春玉米高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    杨长海

    2014-01-01

    Based on the introduction of maize planting technology, the yield increasing effect and efficiency principle, the author gives a detailed description of the cultivation techniques of density-tolerant maize in northern China from plot election and soil preparation, seed treatment, variety selection, fertilization, pest and disease control in an effort to provide a theoretical reference for increasing the yield of Spring Maize in Northern China.%在概述玉米密植技术的增产效果及增产增效原理的基础上,从选地和整地、品种选择、种子处理、施肥、病虫害防治5方面,详细介绍北方地区耐密玉米高产栽培技术要点,为提高北方地区春玉米产量提供理论参考。

  20. Detective quantum efficiency measured as a function of energy for two full-field digital mammography systems

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, N W [Clinical Physics CAU, Barts and The London NHS Trust, St Bartholomew' s Hospital, London, EC1A 6BE (United Kingdom)], E-mail: Nick.Marshall@bartsandthelondon.nhs.uk

    2009-05-07

    This paper presents detective quantum efficiency (DQE) data measured for a range of x-ray beam qualities for two full-field digital mammography (FFDM) systems: a caesium iodide (CsI) detector-based unit and a system designed around an amorphous selenium (a-Se) x-ray detector. Four beam qualities were studied for each system, covering mean energies from 17.8 keV to 23.4 keV for the CsI system and 17.8 keV to 24.7 keV for the a-Se unit. These were set using 2, 4, 6 and 7 cm polymethylmethacralate (PMMA) and typical tube voltage and target/filter combinations selected by the automatic exposure control (AEC) program used clinically on these systems. Normalized noise power spectra (NNPS) were calculated from flood images acquired at these beam qualities for a target detector air kerma of 100 {mu}Gy. Modulation transfer function (MTF) data were acquired at 28 kV and Mo/Mo target/filter setting. The DQE was then calculated from the MTF and NNPS results. For comparison, the quantum detective efficiency (QDE) and energy absorption efficiency (EAE) were calculated from tabulated narrow beam spectral data. With regard to detector response, some energy dependence was noted for pixel value plotted against air kerma at the detector. This amounted to a change in the gradient of the detector response of approximately 15% and 30% per keV for the CsI- and a-Se-based systems, respectively. For the DQE results, a reduction in DQE(0) of 22% was found for the CsI-based unit as beam quality changed from 25 kV Mo/Mo and 2 cm PMMA to 32 kV Rh/Rh and 7 cm PMMA. For the a-Se system, a change in beam quality from 25 kV Mo/Mo and 2 cm PMMA to 34 kV Mo/Rh and 7 cm PMMA led to a reduction in DQE(0) of 8%. Comparing measured data with simple calculations, a reduction in x-ray quantum detection efficiency of 27% was expected for the CsI-based system, while a reduction of 11% was predicted for the a-Se system.

  1. Detective quantum efficiency measured as a function of energy for two full-field digital mammography systems.

    Science.gov (United States)

    Marshall, N W

    2009-05-07

    This paper presents detective quantum efficiency (DQE) data measured for a range of x-ray beam qualities for two full-field digital mammography (FFDM) systems: a caesium iodide (CsI) detector-based unit and a system designed around an amorphous selenium (a-Se) x-ray detector. Four beam qualities were studied for each system, covering mean energies from 17.8 keV to 23.4 keV for the CsI system and 17.8 keV to 24.7 keV for the a-Se unit. These were set using 2, 4, 6 and 7 cm polymethylmethacralate (PMMA) and typical tube voltage and target/filter combinations selected by the automatic exposure control (AEC) program used clinically on these systems. Normalized noise power spectra (NNPS) were calculated from flood images acquired at these beam qualities for a target detector air kerma of 100 microGy. Modulation transfer function (MTF) data were acquired at 28 kV and Mo/Mo target/filter setting. The DQE was then calculated from the MTF and NNPS results. For comparison, the quantum detective efficiency (QDE) and energy absorption efficiency (EAE) were calculated from tabulated narrow beam spectral data. With regard to detector response, some energy dependence was noted for pixel value plotted against air kerma at the detector. This amounted to a change in the gradient of the detector response of approximately 15% and 30% per keV for the CsI- and a-Se-based systems, respectively. For the DQE results, a reduction in DQE(0) of 22% was found for the CsI-based unit as beam quality changed from 25 kV Mo/Mo and 2 cm PMMA to 32 kV Rh/Rh and 7 cm PMMA. For the a-Se system, a change in beam quality from 25 kV Mo/Mo and 2 cm PMMA to 34 kV Mo/Rh and 7 cm PMMA led to a reduction in DQE(0) of 8%. Comparing measured data with simple calculations, a reduction in x-ray quantum detection efficiency of 27% was expected for the CsI-based system, while a reduction of 11% was predicted for the a-Se system.

  2. Relationship between Full-Field Digital Mammographic Features and Clinicopathologic Characteristics in 176 Cases with Breast Cancer

    Institute of Scientific and Technical Information of China (English)

    Zhe Sun; Hongwei Liang; Huimian Xu

    2005-01-01

    OBJECTIVE Different mammographic features are probably predictive of different prognosis. However, ambiguity still exists in understanding the relationship between them. In resent years, digital mammography has been available for clinical use which has led to a revolution in the resolving of images and an increase in early-stage breast cancer detection.Based on the above knowledge, this study was performed to evaluate the relationship between full-field digital mammographic features and clinicopathologic characteristics in breast cancer.METHODS Digital mammograms of 176 patients with pathologically proven breast cancer were reviewed. Also, clinical and pathologic records (histological types and axillary lymph nodes status) were retrospectively examined.RESULTS Most of the patients with a solitary microcalcification were young women under the age of 50(84.4%), but the majority of the patients with microcalcifications complicated by a mass were elderly women. Microcalcifications detected by mammography occurred frequently in ductal carcinoma in situ (28.1%) and in early invasive carcinoma (15.6%). Breast cancers with expression of microcalcifications combined with a spiculate mass had a high metastatic rate of axillary lymph nodes (69.4%). A high metastatic rate of axillary lymph nodes was also found in the patients with solitary worm-like microcalcifications (57.1%), solitary spiculate mass (53.7%) and solitary non-worm-like microcalcifications (44.4%). Simple worm-like microcalcifications accompanied with metastasis of 4 to 9 axillary lymph nodes occurred in 42.9% of the(6/14) cases. The patients with microcalcifications combined by a spiculate mass and with metastasis of 4 to 9 axillary lymph nodes accounted for 27.8% (10/36) of the cases,and those with metastases of 10 and over accounted for 16.7% (6/36).CONCLUSION Solitary microcalcifications occur frequently in young women and are usually associated with early breast cancer. There is a close relationship

  3. High-yielding cultivation techniques of ratooning rice in Changting county%长汀县再生稻丰产栽培技术

    Institute of Scientific and Technical Information of China (English)

    黄玉娥

    2011-01-01

    通过两年千亩再生稻示范,总结出一套再生稻丰产栽培技术。主要技术环节包括选用高产优质、再生力强品种;掌握播种期控制秧龄、适当早插;配方施肥、水分管理增强根系活力;合理留桩促进再生芽生长;及时防治病虫害。%Ratooning rice was planted in 66.7hm2 demonstration field in Changting for two years, a set of high-yielding cultivation techniques were summarized. The techniques included the selection of varieties with traits of high quality and strong regenerative ability, timely sowing and adjusting seedling age, appropriately early transplanting, fomula fertilization and water management to strengthen the vigor of root system, maintaining suitalbe stubble height for promoting the development of regenerated buds, disease and oest control.

  4. Analysis of High Yield and Efficiency Technique in Hybrid Rice Zhongzheyou No.1%杂交水稻中浙优1号高产高效技术途径分析

    Institute of Scientific and Technical Information of China (English)

    刘伟明

    2009-01-01

    To understand the high yield and efficiency technique in hybrid rice Zhongzheyou No.1, we conducted the correlation analysis, regression analysis and path analysis of hybrid rice Zhongzheyou No.1 based on the data of its ear, grain and weight at different yield levels. From this study, we put forward the high yield and efficiency technique in Zhongzheyou No.1: on the basis of certain effective ear number, filled grains per ear should be mainly targeted with a consideration to 1 000-grain weight.

  5. A Dissipation Gap Method for full-field measurement-based identification of elasto-plastic material parameters

    KAUST Repository

    Blaysat, Benoît

    2012-05-18

    Using enriched data such as displacement fields obtained from digital image correlation is a pathway to the local identification of material parameters. Up to now, most of the identification techniques for nonlinear models are based on Finite Element Updating Methods. This article explains how an appropriate use of the Dissipation Gap Method can help in this context and be an interesting alternative to these classical techniques. The Dissipation Gap Methods rely on the concept of error in dissipation that has been used mainly for the verification of finite element simulations. We provide here an original application of these founding developments to the identification of material parameters for nonlinear behaviors. The proposed technique and especially the main technical keypoint of building the admissible fields are described in detail. The approach is then illustrated through the identification of heterogeneous isotropic elasto-plastic properties. The basic numerical features highlighted through these simple examples demonstrate this approach to be a promising tool for nonlinear identification. © 2012 John Wiley & Sons, Ltd.

  6. Implementation and Evaluation of the Virtual Fields Method: Determining Constitutive Model Parameters From Full-Field Deformation Data.

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Sharlotte Lorraine Bolyard; Scherzinger, William M.

    2014-09-01

    The Virtual Fields Method (VFM) is an inverse method for constitutive model parameter identication that relies on full-eld experimental measurements of displacements. VFM is an alternative to standard approaches that require several experiments of simple geometries to calibrate a constitutive model. VFM is one of several techniques that use full-eld exper- imental data, including Finite Element Method Updating (FEMU) techniques, but VFM is computationally fast, not requiring iterative FEM analyses. This report describes the im- plementation and evaluation of VFM primarily for nite-deformation plasticity constitutive models. VFM was successfully implemented in MATLAB and evaluated using simulated FEM data that included representative experimental noise found in the Digital Image Cor- relation (DIC) optical technique that provides full-eld displacement measurements. VFM was able to identify constitutive model parameters for the BCJ plasticity model even in the presence of simulated DIC noise, demonstrating VFM as a viable alternative inverse method. Further research is required before VFM can be adopted as a standard method for constitu- tive model parameter identication, but this study is a foundation for ongoing research at Sandia for improving constitutive model calibration.

  7. Full-field digital mammography: Is the apparent increased detection of microcalcification leading to over-investigation and over-diagnosis?

    Science.gov (United States)

    Porter, Alan J; Evans, Elizabeth B; Erzetich, Lisa M

    2017-08-01

    Modern full-field digital mammography (FFDM) appears to have increased the detection of breast microcalcification. This retrospective study aimed to assess whether this is associated with over-investigation and possible over-diagnosis of breast pathology of lesser significance. Three 2-year periods were studied, in which different mammographic technologies were used exclusively viz., classical screen-film mammography (SFM) in 2003-04, computed radiography (CR) in 2009-10 and FFDM in 2012-13. The study was limited to women in whom biopsy was done for indeterminate, suspicious or malignant (ISM) calcification as the only mammographic abnormality. Between the first and the third time periods, the use of core biopsies and vacuum-assisted biopsies (VABs) for 'ISM calcification only' increased from 0. 6% to 1.4% of all mammograms, and biopsies with malignant results increased from 0.18% to 0.33% of all mammograms. VAB became the preferred technique for biopsy over the study period. The proportion of cores and VABs with a malignant result did not change significantly over the three time periods (24-28%), nor did the proportion of invasive cancers, ductal carcinoma in situ (DCIS) (60-63%) or atypia on subsequent excision. The proportion of DCIS which was of high grade was greatest in the FFDM era (69%). Less than 9% of DCIS were of low grade in all three time periods. Despite increased numbers of biopsies being performed, there was no increase in findings of breast pathology of lesser significance. Improved technology (FFDM and VAB) allows immediate biopsy of small clusters of indeterminate microcalcification, rather than using mammographic surveillance, and this study found no evidence that this has been associated with over-investigation or over-diagnosis. © 2017 The Royal Australian and New Zealand College of Radiologists.

  8. Improved selection of cortical ovarian strips for autotransplantation of ovarian tissue using full-field optical coherence tomography (FFOCT)

    Science.gov (United States)

    Stegehuis, Paulien L.; Peters, Inge T. A.; Eggermont, Jeroen; Kuppen, Peter J. K.; Trimbos, J. Baptist; Lelieveldt, Boudewijn P. F.; van de Velde, Cornelis J. H.; Bosse, Tjalling; Dijkstra, Jouke; Vahrmeijer, Alexander L.

    2016-02-01

    Premature ovarian failure is a major concern in women of reproductive age who undergo gonadotoxic cancer treatment. Autotransplantation of frozen-thawed cortical ovarian tissue allows the immediate start of cancer treatment, but risks reintroduction of cancer. Current tumor detection methods compromise the ovarian tissue's viability and can therefore only be used to exclude the presence of metastases in the cortical ovarian strips that are not transplanted. A non-invasive method is needed that can be used to exclude metastases in the actual ovarian autografts without affecting the tissue's viability. In this study we applied FFOCT - a non-fixative technique that uses white light interferometry to make highresolution images (1μm isotropic) of fresh tissue - to study healthy and malignant ovarian tissue. We created an image atlas of healthy ovarian tissues from premenopausal patients and ovarian tissues with breast cancer metastases. To get the best possible match between hematoxylin-and-eosin stained slides and FFOCT images formalinfixed paraffin-embedded tissue samples were deparaffinized and FFOCT images were acquired within a few minutes. FFOCT images were compared with histology images. All normal structures such as follicles in all phases, inclusion cysts, blood vessels, corpora lutea, and corpora albicantia were clearly recognizable. Ovarian metastases could be well distinguished from normal ovarian tissue. FFOCT is a promising technique in the field of fertility preservation: metastases can be detected and additionally cortical ovarian strips can be selected on the basis of high follicle density.

  9. Blind identification of full-field vibration modes of output-only structures from uniformly-sampled, possibly temporally-aliased (sub-Nyquist), video measurements

    Science.gov (United States)

    Yang, Yongchao; Dorn, Charles; Mancini, Tyler; Talken, Zachary; Nagarajaiah, Satish; Kenyon, Garrett; Farrar, Charles; Mascareñas, David

    2017-03-01

    what is required by the Shannon-Nyquist sampling theorem for output-only modal analysis. In particular, the spatio-temporal uncoupling property of the modal expansion of structural vibration responses enables a direct modal decoupling of the temporally-aliased vibration measurements by existing output-only modal analysis methods, yielding (full-field) mode shapes estimation directly. Then the signal aliasing properties in modal analysis is exploited to estimate the modal frequencies and damping ratios. The proposed method is validated by laboratory experiments where output-only modal identification is conducted on temporally-aliased acceleration responses and particularly the temporally-aliased video measurements of bench-scale structures, including a three-story building structure and a cantilever beam.

  10. Optimizing nitrogen management for soft red winter wheat yield, grain protein, and grain quality using precision agriculture and remote sensing techniques

    Science.gov (United States)

    Farrer, Dianne Carter

    The purpose of this research was to improve the management of soft red winter wheat (Triticum aestivum L.) in North Carolina. There were three issues addressed; the quality of the grain as affected by delayed harvest, explaining grain protein variability through nitrogen (N) management, and developing N recommendations at growth stage (GS) 30 using aerial color infrared (CIR) photography. The impact of delayed harvest on grain yield, test weight, grain protein, and 20 milling and baking quality parameters was studied in three trials in 2002 and three trials in 2003. Yield was significantly reduced in three out of five trials due to dry, warm environments, possibly indicating shattering. Test weights were significantly reduced in five out of six trials and were positively correlated to the number of precipitation events and to the number of days between harvests, indicating the negative effects of wetting and drying cycles. Grain protein was not affected by delayed harvest. Of the 20 quality parameters investigated, flour falling number, clear flour, and farinograph breakdown times were significantly reduced due to delayed harvest, while grain deoxynivalenol (DON) levels increased with a delayed harvest. Grain protein content in soft red winter wheat is highly variable across years and environments. A second study examined the effects of different nitrogen (N) fertilizer rates and times of application on grain protein variability. Seven different environments were utilized in this study. Though environment contributed about 23% of grain protein variability, the majority of that variability (52%) was attributed to N management. It was found that as grain protein levels increased at higher N rates, so did overall protein variability as indicated by the three stability indexes employed. In addition, applying the majority of total N at growth stage (GS) 30 decreased grain protein stability. Site-specific N management systems using remote sensing techniques can

  11. Optical low-cost and portable arrangement for full field 3D displacement measurement using a single camera

    Science.gov (United States)

    López-Alba, E.; Felipe-Sesé, L.; Schmeer, S.; Díaz, F. A.

    2016-11-01

    In the current paper, an optical low-cost system for 3D displacement measurement based on a single camera and 3D digital image correlation is presented. The conventional 3D-DIC set-up based on a two-synchronized-cameras system is compared with a proposed pseudo-stereo portable system that employs a mirror system integrated in a device for a straightforward application achieving a novel handle and flexible device for its use in many scenarios. The proposed optical system splits the image by the camera into two stereo images of the object. In order to validate this new approach and quantify its uncertainty compared to traditional 3D-DIC systems, solid rigid in and out-of-plane displacements experiments have been performed and analyzed. The differences between both systems have been studied employing an image decomposition technique which performs a full image comparison. Therefore, results of all field of view are compared with those using a stereoscopy system and 3D-DIC, discussing the accurate results obtained with the proposed device not having influence any distortion or aberration produced by the mirrors. Finally, the adaptability of the proposed system and its accuracy has been tested performing quasi-static and dynamic experiments using a silicon specimen under high deformation. Results have been compared and validated with those obtained from a conventional stereoscopy system showing an excellent level of agreement.

  12. High-yield Cultivation Techniques and Exploitation of Sweet Corn%甜玉米高产栽培技术和开发利用

    Institute of Scientific and Technical Information of China (English)

    尚赏; 郭书亚; 张艳; 汤其宁; 卢广远

    2014-01-01

    Sweet corn as a new vegetable and fruit food,already obtained the rapid development at home and abroad. The sweet corn had more polysaccharides,proteins and vitamins than normal corn contains,and had the good food taste,easy to digest and had high nutritional value. Sweet corn was developed using as the frozen food and processed into canned food,also as fresh corn for sale. Sweet corn had considerable economic benefits and wide market foreground. On the basis of quality traits and growth characteristics of sweet corn,and combined with the local production conditions,Systematically discussed and summarized the high yield cultivation techniques and the development and utilization of sweet corn.%由于甜玉米比普通玉米富含多糖、蛋白质及维生素,并且食用口感好、易于消化和营养价值极高,所以作为新兴蔬菜兼水果型食品,已经在国内外得到迅速发展。甜玉米的开发利用除作为速冻食品和加工成罐头食品外,也可以作为鲜食玉米出售。甜玉米具有较可观的经济效益和广阔的市场发展前景。该文介绍了甜玉米的品质性状、生育特点、高产栽培技术和开发利用。

  13. X-ray induced formation of γ-H2AX foci after full-field digital mammography and digital breast-tomosynthesis.

    Directory of Open Access Journals (Sweden)

    Siegfried A Schwab

    Full Text Available PURPOSE: To determine in-vivo formation of x-ray induced γ-H2AX foci in systemic blood lymphocytes of patients undergoing full-field digital mammography (FFDM and to estimate foci after FFDM and digital breast-tomosynthesis (DBT using a biological phantom model. MATERIALS AND METHODS: The study complies with the Declaration of Helsinki and was performed following approval by the ethic committee of the University of Erlangen-Nuremberg. Written informed consent was obtained from every patient. For in-vivo tests, systemic blood lymphocytes were obtained from 20 patients before and after FFDM. In order to compare in-vivo post-exposure with pre-exposure foci levels, the Wilcoxon matched pairs test was used. For in-vitro experiments, isolated blood lymphocytes from healthy volunteers were irradiated at skin and glandular level of a porcine breast using FFDM and DBT. Cells were stained against the phosphorylated histone variant γ-H2AX, and foci representing distinct DNA damages were quantified. RESULTS: Median in-vivo foci level/cell was 0.086 (range 0.067-0.116 before and 0.094 (0.076-0.126 after FFDM (p = 0.0004. In the in-vitro model, the median x-ray induced foci level/cell after FFDM was 0.120 (range 0.086-0.140 at skin level and 0.035 (range 0.030-0.050 at glandular level. After DBT, the median x-ray induced foci level/cell was 0.061 (range 0.040-0.081 at skin level and 0.015 (range 0.006-0.020 at glandular level. CONCLUSION: In patients, mammography induces a slight but significant increase of γ-H2AX foci in systemic blood lymphocytes. The introduced biological phantom model is suitable for the estimation of x-ray induced DNA damages in breast tissue in different breast imaging techniques.

  14. Mechanistic model to predict colostrum intake based on deuterium oxide dilution technique data and impact of gestation and prefarrowing diets on piglet intake and sow yield of colostrum.

    Science.gov (United States)

    Theil, P K; Flummer, C; Hurley, W L; Kristensen, N B; Labouriau, R L; Sørensen, M T

    2014-12-01

    The aims of the present study were to quantify colostrum intake (CI) of piglets using the D2O dilution technique, to develop a mechanistic model to predict CI, to compare these data with CI predicted by a previous empirical predictive model developed for bottle-fed piglets, and to study how composition of diets fed to gestating sows affected piglet CI, sow colostrum yield (CY), and colostrum composition. In total, 240 piglets from 40 litters were enriched with D2O. The CI measured by D2O from birth until 24 h after the birth of first-born piglet was on average 443 g (SD 151). Based on measured CI, a mechanistic model to predict CI was developed using piglet characteristics (24-h weight gain [WG; g], BW at birth [BWB; kg], and duration of CI [D; min]: CI, g=-106+2.26 WG+200 BWB+0.111 D-1,414 WG/D+0.0182 WG/BWB (R2=0.944). This model was used to predict the CI for all colostrum suckling piglets within the 40 litters (n=500, mean=437 g, SD=153 g) and was compared with the CI predicted by a previous empirical predictive model (mean=305 g, SD=140 g). The previous empirical model underestimated the CI by 30% compared with that obtained by the new mechanistic model. The sows were fed 1 of 4 gestation diets (n=10 per diet) based on different fiber sources (low fiber [17%] or potato pulp, pectin residue, or sugarbeet pulp [32 to 40%]) from mating until d 108 of gestation. From d 108 of gestation until parturition, sows were fed 1 of 5 prefarrowing diets (n=8 per diet) varying in supplemented fat (3% animal fat, 8% coconut oil, 8% sunflower oil, 8% fish oil, or 4% fish oil+4% octanoic acid). Sows fed diets with pectin residue or sugarbeet pulp during gestation produced colostrum with lower protein, fat, DM, and energy concentrations and higher lactose concentrations, and their piglets had greater CI as compared with sows fed potato pulp or the low-fiber diet (Pcolostrum compared with other prefarrowing diets (Pcolostrum composition.

  15. Anti-Stokes effect CCD camera and SLD based optical coherence tomography for full-field imaging in the 1550nm region

    Science.gov (United States)

    Kredzinski, Lukasz; Connelly, Michael J.

    2012-06-01

    Full-field Optical coherence tomography is an en-face interferometric imaging technology capable of carrying out high resolution cross-sectional imaging of the internal microstructure of an examined specimen in a non-invasive manner. The presented system is based on competitively priced optical components available at the main optical communications band located in the 1550 nm region. It consists of a superluminescent diode and an anti-stokes imaging device. The single mode fibre coupled SLD was connected to a multi-mode fibre inserted into a mode scrambler to obtain spatially incoherent illumination, suitable for OCT wide-field modality in terms of crosstalk suppression and image enhancement. This relatively inexpensive system with moderate resolution of approximately 24um x 12um (axial x lateral) was constructed to perform a 3D cross sectional imaging of a human tooth. To our knowledge this is the first 1550 nm full-field OCT system reported.

  16. Evaluation of patient dose saving in grid-less x-ray mammography acquisition compared with full field digital mammography (FFDMG) acquisition

    DEFF Research Database (Denmark)

    Abdi, Ahmed Jibril; Mussmann, Bo Redder

    2017-01-01

    Purpose: To investigate the patient radiation dose saving of grid-less X-ray mammography acquisitions compared with conventional full-field digital X-ray mammography (FFDMG). Methods and materials: The Siemens Inspiration MAMMOMAT PRIME system with Software Based Scatter Correction (SBSC) was used...... to investigate the dose saving in grid-less acquisition compared with conventional full-field digital mammography (FFDMG) acquisitions. A Piranha 657 was used to measure the entrance exposure. The entrance exposure was directly measured on different PMMA thicknesses of 20-70mm in steps of 10mm. The PMMA block...... thicknesses were then converted to an equivalent compressed breast tissue thicknesses. The average glandular dose (AGD) is calculated. Results: Dose reduction in both the directly measured entrance exposure and the calculated AGD is between 13% and 32% in the grid-less mammography acquisition. The contrast...

  17. [First experiments for the detection of simulated mammographic lesions: digital full field mammography with a new detector with a double plate of pure selenium].

    Science.gov (United States)

    Schulz-Wendtland, R; Hermann, K-P; Wenkel, E; Adamietz, B; Lell, M; Anders, K; Uder, M

    2011-02-01

    The article describes an experimental phantom study of a system for digital full field mammography with a new digital detector with a double plate of pure selenium. The experiments were carried out with the new full field digital mammography system Amulet from FujiFilm. This system has a new detector (18×24 cm(2)) on the basis of highly purified amorphous selenium (a-Se) with a pixel size of 50 µm. The x-rays are converted into electric signals in the first plate which are read into the second plate with the help of an optical switch and demonstrated in the form of an image. In this way a better pixel size/volume and signal-to-noise ratio should be achieved. The object of the investigation was the Wisconsin Mammographic Random Phantom, Model 152 A (Technical Performance Mo/Mo, 28 kV, 100 mAs). Five investigators with different experiences in mammography each received three images on a monitor with different random positions of the simulated lesions in the phantom for assessment. The detection rates were compared under the same conditions with the results of two other full field digital mammography systems. The median detection rate for all images and investigators for the new doubled plated a-Se detector with optical switch was 98.7%. For both other systems with a-Si or and a-Se detectors the detection rate was 89.8% or 97.3%, respectively. There were no significant differences in the detection rate of the simulated breast lesions for all three systems considering the interobserver and intraobserver variation. The first phantom study for the detection of simulated breast lesions with the new full field digital mammography system Amulet demonstrates equivalent results with the other systems used in the clinical routine. The trend towards superiority of the new system has to be confirmed in further clinical studies.

  18. Genome-wide association mapping in winter barley for grain yield and culm cell wall polymer content using the high-throughput CoMPP technique

    DEFF Research Database (Denmark)

    Bellucci, Andrea; Tondelli, Alessandro; Fangel, Jonatan Ulrik

    2017-01-01

    -wide association study (GWAS). Marker-trait associations (MTA) were analyzed for grain yield and cell wall determination by LM6 and JIM13 as these were the traits showing significant correlations between the years. A single QTL for GYLD containing three MTAs was found on chromosome 3H located close to the Hv-eIF4E...

  19. TECHNIQUES FOR MAKING BIOLOGICS AND MINERAL NITROGEN AND THEIR INFLUENCE ON THE YIELD OF THE MIXED CROPS IN THE CONDITIONS OF GREY FOREST SOILS

    Directory of Open Access Journals (Sweden)

    Shkotova O. N.

    2016-04-01

    Full Text Available In the conditions of grey forest soils in the Bryansk region among the fodder crops widespread mixed legume-cereal crops. The results showed that the photosynthetic activity of cereals and leguminous crops and their yields in mixed crops depended on made of biological and mineral nitrogen fertilizers. It is established that the nitrogen in the form of ammonium nitrate has a positive impact on the formation of assimilating leaf surface, photosynthetic potential and net productivity and yield of grain mixture in lupine-barley and soybean -barley cropping and pea-barley crops the use of nitrogen in the form of potassium nitrate was more favorable. It was found that in lupine-barley crops the active symbiotic potential has increased by 25,5% and the yield increased by 21,3% , in soybean-barley crops 28,5% and 19,2% respectively, due to the joint use of a mixture of symbiotic and associative rhizobacteria and mineral nitrogen in the form of ammonium nitrate in the dose of N60. In pea-barley agrocenosis it has improved the efficiency of cultivation of joint application of mixed inoculant symbiotic and associative rhizobacteria on the background of the application of mineral nitrogen in the form of potassium nitrate in the dose of N60, where there was an increase of the active symbiotic potential by 34,7% and grain yield by 24,7% compared to the option when adding the mixture of biological products

  20. The influence of solid/liquid separation techniques on the sugar yield in two-step dilute acid hydrolysis of softwood followed by enzymatic hydrolysis

    Directory of Open Access Journals (Sweden)

    Galbe Mats

    2009-03-01

    Full Text Available Abstract Background Two-step dilute acid hydrolysis of softwood, either as a stand-alone process or as pretreatment before enzymatic hydrolysis, is considered to result in higher sugar yields than one-step acid hydrolysis. However, this requires removal of the liquid between the two steps. In an industrial process, filtration and washing of the material between the two steps is difficult, as it should be performed at high pressure to reduce energy demand. Moreover, the application of pressure leads to more compact solids, which may affect subsequent processing steps. This study was carried out to investigate the influence of pressing the biomass, in combination with the effects of not washing the material, on the sugar yield obtained from two-step dilute acid hydrolysis, with and without subsequent enzymatic digestion of the solids. Results Washing the material between the two acid hydrolysis steps, followed by enzymatic digestion, resulted in recovery of 96% of the mannose and 81% of the glucose (% of the theoretical in the liquid fraction, regardless of the choice of dewatering method (pressing or vacuum filtration. Not washing the solids between the two acid hydrolysis steps led to elevated acidity of the remaining solids during the second hydrolysis step, which resulted in lower yields of mannose, 85% and 74% of the theoretical, for the pressed and vacuum-filtered slurry, respectively, due to sugar degradation. However, this increase in acidity resulted in a higher glucose yield (94.2% from pressed slurry than from filtered slurry (77.6%. Conclusion Pressing the washed material between the two acid hydrolysis steps had no significant negative effect on the sugar yields of the second acid hydrolysis step or on enzymatic hydrolysis. Not washing the material resulted in a harsher second acid hydrolysis step, which caused greater degradation of the sugars during subsequent acid hydrolysis of the solids, particularly in case of the vacuum

  1. [Comparison of dignity determination of mammographic microcalcification with two systems for digital full-field mammography with different detector resolution: a retrospective clinical study].

    Science.gov (United States)

    Schulz-Wendtland, R; Hermann, K-P; Adamietz, B; Meier-Meitinger, M; Wenkel, E; Lell, M; Anders, K; Uder, M

    2011-02-01

    The aim of this retrospective clinical study was to compare the diagnostic accuracy of the novel 50 µm FFDM (full-field digital mammography) system (DR) with an established 70 µm system (DR) in the differential diagnosis between benign and malignant clusters of microcalcification (n=50) (BI-RADS™ classification 4/5) and to assess the possible incremental value of the 50 µm pixel-pitch on specificity. From March 2009 to September 2009, 50 patients underwent full-field digital mammography (FFDM) (detector resolution 70 µm) (Novation, Siemens, Erlangen, Germany). As there were suspicious signs of microcalcification classified with BI-RADS™ 4/5 after diagnosis and preoperative wire localization, control images were made with the new FFDM system (detector: resolution 50 µm) (Amulet, Fujifilm, Tokyo, Japan) with the same exposure parameters. The diagnosis was determined after the operation by five radiologists with different experience in digital mammography from randomly distributed mediolateral views (monitor reading) whose results were correlated with the final histology of all lesions. Histopathology revealed 19 benign and 31 malignant lesions in 50 patients after open biopsy. The results of the five readers showed a higher sensitivity of the new FFDM system (80.0%) in the ability to recognize malignant microcalcification in comparison to the established system (74.8%). The specificity (75.8 versus 71.6%) was slightly higher for the new system but these results were not statistically significant (p<0.001). Considering the diagnostic accuracy, the new system (detector: resolution 50 µm) was also slightly superior to the well-known system (detector: resolution 70 µm) (80.1% versus 76.4%). Our study has shown that the new full-field digital mammography system using the novel detector compared with the already established FFDM system with respect to the assessment of microcalcification is at least equivalent.

  2. The effect of the operation conditions and the extraction techniques on the yield, kinetics and composition of methanol extracts of Hieracium pilosella L.

    Directory of Open Access Journals (Sweden)

    Stanojević Ljiljana P.

    2009-01-01

    Full Text Available The optimal operational extraction conditions were determined by investigating the influence of the methanol concentration, solvomodule and temperature of the maceration extraction on the yield and kinetics of total extractive matter, chlorogenic acid, umbelliferone and apigenin-7-O-glucoside from Hieracium pilosella L. Based on the results of Soxhlet and Tillepape extraction kinetics investigations of the total extractive matter and the components under the optimal maceration operation conditions it was found that the highest yields of the extractive matter and investigated bioactive components extracted from the dry plant material were obtained by using the Soxhlet extraction method. The contents of chlorogenic acid, umbelliferone and apigenin-7-O-glucoside in the extracts were determined by HPLC method. Chlorogenic acid is the component with the highest share in all the extracts.

  3. Observation of coupled vortex gyrations by 70-ps-time and 20-nm-space- resolved full-field magnetic transmission soft x-ray microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Hyunsung; Yu, Young-Sang; Lee, Ki-Suk; Im, Mi-Young; Fischer, Peter; Bocklage, Lars; Vogel, Andreas; Bolte, Markus; Meier, Guido; Kim, Sang-Koog

    2010-09-01

    We employed time-and space-resolved full-field magnetic transmission soft x-ray microscopy to observe vortex-core gyrations in a pair of dipolar-coupled vortex-state Permalloy (Ni{sub 80}Fe{sub 20}) disks. The 70 ps temporal and 20 nm spatial resolution of the microscope enabled us to simultaneously measure vortex gyrations in both disks and to resolve the phases and amplitudes of both vortex-core positions. We observed their correlation for a specific vortex-state configuration. This work provides a robust and direct method of studying vortex gyrations in dipolar-coupled vortex oscillators.

  4. Brain refractive index measured in vivo with high-NA defocus-corrected full-field OCT and consequences for two-photon microscopy.

    Science.gov (United States)

    Binding, Jonas; Ben Arous, Juliette; Léger, Jean-François; Gigan, Sylvain; Boccara, Claude; Bourdieu, Laurent

    2011-03-14

    Two-photon laser scanning microscopy (2PLSM) is an important tool for in vivo tissue imaging with sub-cellular resolution, but the penetration depth of current systems is potentially limited by sample-induced optical aberrations. To quantify these, we measured the refractive index n' in the somatosensory cortex of 7 rats in vivo using defocus optimization in full-field optical coherence tomography (ff-OCT). We found n' to be independent of imaging depth or rat age. From these measurements, we calculated that two-photon imaging beyond 200 µm into the cortex is limited by spherical aberration, indicating that adaptive optics will improve imaging depth.

  5. Planting Performance and High-yielding Cultivation Techniques of Direct Seeding and Later Throwing%早直播晚抛秧高产示范表现及配套栽培技术

    Institute of Scientific and Technical Information of China (English)

    李华; 贺晓鹏

    2016-01-01

    This study was conducted in rice seed stock station in Jiangxi province in 2015 live early, late some high-yield demonstration, on average every 667m2 production of 1 159.1 kg. This paper summarized the early live late some high-yield group structure, the best fertilizer rate and high yield cultivation techniques.%2015年在江西省水稻原种场进行了早直播、晚抛秧高产示范,平均每667m2产量达1159.1kg。根据示范结果,总结了早直播晚抛秧高产群体结构、最佳施肥量及配套高产栽培技术。

  6. Comparison on extraction yield of sennoside A and sennoside B from senna (Cassia angustifolia) using conventional and non conventional extraction techniques and their quantification using a validated HPLC-PDA detection method.

    Science.gov (United States)

    Dhanani, Tushar; Singh, Raghuraj; Reddy, Nagaraja; Trivedi, A; Kumar, Satyanshu

    2017-05-01

    Senna is an important medicinal plant and is used in many Ayurvedic formulations. Dianthraquinone glucosides are the main bioactive phytochemicals present in leaves and pods of senna. The extraction efficiency in terms of yield and composition of the extract of senna prepared using both conventional (cold percolation at room temperature and refluxing) and non conventional (ultrasound and microwave assisted solvent extraction as well as supercritical fluid extraction) techniques were compared in the present study. Also a rapid reverse phase HPLC-PDA detection method was developed and validated for the simultaneous determination of sennoside A and sennoside B in the different extracts of senna leaves. Ultrasound and microwave assisted solvent extraction techniques were more effective in terms of yield and composition of the extracts compared to cold percolation at room temperature and refluxing methods of extraction.

  7. 荷兰豆—优质稻—甘薯高产栽培技术%Pea Pods-Quality Rice-Sweet Potato High Yield Cultivation Techniques

    Institute of Scientific and Technical Information of China (English)

    王来清; 赖德才

    2012-01-01

    Pea pods-qality rce-sweet potato high yield cultivation techniques summed up through the"Whole City Money-Grain Harvest Competition"practice that launched by Sanming municipal government,was an efficient planting pattern suitable for extension in Qingliu county.High yield cultivation techniques for pea pods,high quality rice,sweet potato were briefly introduced in this paper.%荷兰豆—优质稻—甘薯高产栽培技术是三明市政府组织的全市粮钱丰收竞赛活动实践中总结出来的适应清流县推广的高效种植模式,文章就荷兰豆、优质稻、甘薯的高产栽培技术作简要介绍。

  8. Testing of full-field digital mammography%全数字化乳腺X线设备检测方法

    Institute of Scientific and Technical Information of China (English)

    陈强; 倪萍; 蔡华

    2015-01-01

    Objective To test the key indexes of full-field digital mammography to keep it in good condition.Methods The testing was carried out based on clinical experiences and GBZ 186—2007 Mammography Quality Control Testing Specification.Results The testing items and indexes were proposed to facilitate the staff to check and operate the machine.Conclusion Clinical safety of full-field digital mammography and image quality are both enhanced greatly.%目的:通过对全数字化乳腺X线设备主要参数进行检测,从而保证设备性能良好.方法:依据GBZ 186—2007《乳腺X射线摄影质量控制检测规范》并结合临床实际制定检测方法,对全数字化乳腺X线设备性能进行评估.结果:提供了详细的检测项目和结果,使操作人员能更好地检测和使用设备.结论:该检测方法为全数字化乳腺X线设备临床使用安全及影像质量提供了必要保障.

  9. High Yield Cultural Technique of Long Yam in Yichang Area%宜昌地区长山药高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    王鹏程; 宋晓东; 常红青; 许安频; 陈兵

    2012-01-01

    长山药(Dioscorea batatas Decne.)是药食兼用植物,近几年受到越来越多消费者的青睐.通过几年的长山药栽培实践,总结出了一套适宜在宜昌地区推广应用的长山药优质高产栽培技术.%Long yam(Dioscorea batatas Decne.) is a medicinal and edible plant. Because of its health value, it has gotten more and more consumer's interests in recent years. A set of high quality and high yield cultivation technology suitable for popularization in Yichang area were summarized through years of yam cultivation practice.

  10. Preliminary results from multicenter clinical trials for detection of cervical squamous intraepithelial lesions using a novel full-field evoked-tissue-flourescence-based imaging instrument

    Science.gov (United States)

    Dattamajumdar, Anupam K.; Wells, D.; Parnell, Julie R.; Ganguly, Dipankur; Wright, Thomas C., Jr.

    2001-10-01

    We report preliminary results from a multi-center trial of evaluating the performance of a novel, full-field multi-spectral tissue fluorescence imaging system (CerviscanTM) designed to detect cervical squamous intraepithelial lesions. Spectral data from multiple regions of 48 patients enrolled from clinical performance sites in the US and Canada are included in this preliminary analysis. This includes 30 women used for the training set and 18 used for the testing set. In the testing set, 37/43 SIL and 70/80 NonSIL regions were correctly identified for a sensitivity of 86% and specificity of 87.5%. CerviscanTM locates cervical precancerous lesions with high sensitivity and specificity and has the potential to permit 'see and treat' patient management.

  11. Experimental comparison of perfusion imaging systems using multi-exposure laser speckle, single-exposure laser speckle, and full-field laser Doppler

    Science.gov (United States)

    Thompson, Oliver; Bakker, Jimmy; Kloeze, Carla; Hondebrink, Erwin; Steenbergen, Wiendelt

    2012-03-01

    A variety of laser Doppler and laser speckle contrast systems have been constructed by various groups and companies, for commercial sale and for research. All rely on the same physical phenomenon - the dynamic laser speckle pattern generated by illuminating tissue with coherent light - but differ in details of system design, operation and analysis. We present a comparison between measurements made with three systems: a multi-exposure laser speckle contrast system built at Industrial Research Ltd, a commercial single-exposure laser speckle contrast system developed by Perimed AB (PSI NR) and the full-field laser Doppler camera built by the University of Twente (TOPCam). We compare the response to changing flows of all three systems. The systems are found to produce similar results for a variety of in-vivo and in-vitro measurements. Multi-exposure speckle contrast shows some advantages in information gained and insensitivity to static speckle, at the cost of increased complexity and measurement time.

  12. Rapid skin profiling with non-contact full-field optical coherence tomography: study of patients with diabetes mellitus type I

    Science.gov (United States)

    Zakharov, P.; Talary, M. S.; Kolm, I.; Caduff, A.

    2009-07-01

    The application of the full-field optical coherence tomography (OCT) microscope to the characterisation of skin morphology is described. An automated procedure for analysis and interpretation of the OCT data has been developed which provides measures of the laterally averaged depth profiles of the skin reflectance. The skin at the dorsal side of the upper arm of 22 patients with Type 1 Diabetes Mellitus has been characterised in a non-contact way. The OCT signal profile was compared with the optical histological data obtained with a commercial confocal microscope (CM). The highest correlation to the epidermal thickness (ET) obtained using CM was found for the distance from the entrance OCT peak to the first minimum of the reflection profile (R2=0.657, pdiabetes or concentration of glycated haemoglobin in the blood.

  13. Deep learning in breast cancer risk assessment: evaluation of convolutional neural networks on a clinical dataset of full-field digital mammograms.

    Science.gov (United States)

    Li, Hui; Giger, Maryellen L; Huynh, Benjamin Q; Antropova, Natalia O

    2017-10-01

    To evaluate deep learning in the assessment of breast cancer risk in which convolutional neural networks (CNNs) with transfer learning are used to extract parenchymal characteristics directly from full-field digital mammographic (FFDM) images instead of using computerized radiographic texture analysis (RTA), 456 clinical FFDM cases were included: a "high-risk" BRCA1/2 gene-mutation carriers dataset (53 cases), a "high-risk" unilateral cancer patients dataset (75 cases), and a "low-risk dataset" (328 cases). Deep learning was compared to the use of features from RTA, as well as to a combination of both in the task of distinguishing between high- and low-risk subjects. Similar classification performances were obtained using CNN [area under the curve [Formula: see text]; standard error [Formula: see text

  14. Quantitative x-ray magnetic circular dichroism mapping with high spatial resolution full-field magnetic transmission soft x-ray spectro-microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, MacCallum J. [Center for X-ray Optics, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Physics Department, University of California, Berkeley, California 94720 (United States); Agostino, Christopher J. [Physics Department, University of California, Berkeley, California 94720 (United States); National Center for Electron Microscopy, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); N' Diaye, Alpha T. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Chen, Gong [National Center for Electron Microscopy, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Im, Mi-Young [Center for X-ray Optics, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Emerging Materials Science, Daegu Gyeongbuk Institute of Science and Technology, Daegu 711-873 (Korea, Republic of); Fischer, Peter, E-mail: PJFischer@lbl.gov [Center for X-ray Optics, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Physics Department, University of California, Santa Cruz, California 94056 (United States)

    2015-05-07

    The spectroscopic analysis of X-ray magnetic circular dichroism (XMCD), which serves as strong and element-specific magnetic contrast in full-field magnetic transmission soft x-ray microscopy, is shown to provide information on the local distribution of spin (S) and orbital (L) magnetic moments down to a spatial resolution of 25 nm limited by the x-ray optics used in the x-ray microscope. The spatially resolved L/S ratio observed in a multilayered (Co 0.3 nm/Pt 0.5 nm) × 30 thin film exhibiting a strong perpendicular magnetic anisotropy decreases significantly in the vicinity of domain walls, indicating a non-uniform spin configuration in the vertical profile of a domain wall across the thin film. Quantitative XMCD mapping with x-ray spectro-microscopy will become an important characterization tool for systems with topological or engineered magnetization inhomogeneities.

  15. Should processed or raw image data be used in mammographic image quality analyses? A comparative study of three full-field digital mammography systems.

    Science.gov (United States)

    Borg, Mark; Badr, Ishmail; Royle, Gary

    2015-01-01

    The purpose of this study is to compare a number of measured image quality parameters using processed and unprocessed or raw images in two full-field direct digital units and one computed radiography mammography system. This study shows that the difference between raw and processed image data is system specific. The results have shown that there are no significant differences between raw and processed data in the mean threshold contrast values using the contrast-detail mammography phantom in all the systems investigated; however, these results cannot be generalised to all available systems. Notable differences were noted in contrast-to-noise ratios and in other tests including: response function, modulation transfer function , noise equivalent quanta, normalised noise power spectra and detective quantum efficiency as specified in IEC 62220-1-2. Consequently, the authors strongly recommend the use of raw data for all image quality analyses in digital mammography.

  16. Yield Improvement in Steel Casting (Yield II)

    Energy Technology Data Exchange (ETDEWEB)

    Richard A. Hardin; Christoph Beckermann; Tim Hays

    2002-02-18

    This report presents work conducted on the following main projects tasks undertaken in the Yield Improvement in Steel Casting research program: Improvement of Conventional Feeding and Risering Methods, Use of Unconventional Yield Improvement Techniques, and Case Studies in Yield Improvement. Casting trials were conducted and then simulated using the precise casting conditions as recorded by the participating SFSA foundries. These results present a statistically meaningful set of experimental data on soundness versus feeding length. Comparisons between these casting trials and casting trials performed more than forty years ago by Pellini and the SFSA are quite good and appear reasonable. Comparisons between the current SFSA feeding rules and feeding rules based on the minimum Niyama criterion reveal that the Niyama-based rules are generally less conservative. The niyama-based rules also agree better with both the trials presented here, and the casting trails performed by Pellini an d the SFSA years ago. Furthermore, the use of the Niyama criterion to predict centerline shrinkage for horizontally fed plate sections has a theoretical basis according to the casting literature reviewed here. These results strongly support the use of improved feeding rules for horizontal plate sections based on the Niyama criterion, which can be tailored to the casting conditions for a given alloy and to a desired level of soundness. The reliability and repeatability of ASTM shrinkage x-ray ratings was investigated in a statistical study performed on 128 x-rays, each of which were rated seven different times. A manual ''Feeding and Risering Guidelines for Steel Castings' is given in this final report. Results of casting trials performed to test unconventional techniques for improving casting yield are presented. These use a stacked arrangement of castings and riser pressurization to increase the casting yield. Riser pressurization was demonstrated to feed a casting up to

  17. A dissipation based method for identifying hererogeneous material properties using full-field measurements [Une approche en dissipation pour l'identification de proprié tés matériaux hétérogènes à partir de mesures de champs

    KAUST Repository

    Lubineau, Gilles

    2012-01-01

    The full field measurement technique has become a popular technique for the quick identification of complex and/or heterogeneous-in-space material behaviors. Based on the rich available corpus of information, this technique makes possible to identify complex evolution laws using few highly heterogeneous testing. Multiple techniques have been proposed up to now. Here, we detail the application of the constitutive error relation to the identification of linear elastic material models.Then, the natural extension of the constitutive equation gap method through a dissipation gap method is discussed for the identification of material behaviors involving dissipation. 2D reference examples are provided for each method. © 2012 EDP Sciences.

  18. 黑麦草高产栽培技术研究%Study on high-yield cultivation techniques of rye grass

    Institute of Scientific and Technical Information of China (English)

    孙学映; 刘春英; 朱体超; 陈光蓉

    2013-01-01

    [Objective]The effects of plant density,fertilization and cutting frequency on rye grass yield were studied to develop high-yield cultivation technical measures.[Method]Using quadratic regression orthogonal rotation combination design of five factors,mathematical models between dry yield (y),planting density(x1),N(x2),P2O5(x3),K2O(x4) application amount,and cutting frequency (x5) were established for simulation optimization.[Result]According to the results of regression analysis,the regression equation between rye grass yield and the five factors (x) was y=29861.05+205.42x1+1147.51 x2+327.55x3-23.07x4-787.03x5-956.48X1-833.09x2-693.68x32-69556x42-1076.17x52 +215.13x1x2+167.78X1X3-133.28x1x4-84.35x1x5 +142.74x2x3-87.91x2x4-67.82x2x5-154.31x3x4-50.49x3x5-246.39x4x5.Using the comprehensive agricultural measures with planting density of 3.17-3.25 ten thousand/ha,pure N 138.09-145.17 kg/ha,P2O5 25.88-28.12 kggha,K2O 87.21-92.79 kg/ha and 3 times of mowing during whole growth stages (before or after heading stage cutting),the yield was over 27024.40 kg/ha.[Conclusion]For local rye grass production,there should be more N fertilizers,wider plant distance and controlled cutting times,while regarding adjustment in other regions,soil fertility,climate conditions and other factors should be taken into account.%[目的]研究种植密度、施肥量和刈割次数对黑麦草产量的影响,为黑麦草高产栽培技术提供措施.[方法]采用五元二次回归正交旋转组合设计,建立黑麦草干草产量(y)与种植密度(x1)、N(x2)、P2O5(x3)、K2O(x4)和刈割次数(x5)之间的数学模型,并模拟寻优.[结果]经回归分析,得到黑麦草干草产量(y)与五因子(x)间的回归方程为:y=29861.05+205.42x1+ 1147.5 lx2+327.55x3-23.07x4-787.03x5-956.48x12-833.09x22-693.68x32-695.56x42-1076.17x52+215.13x1x2+ 167.78x1x3-133.28x1x4-84.35x1x5+ 142.74x2x3-87.91x2x4-67.82x2x5-154.31x3x4-50.49x3x5-246.39x4x5.采用种植密度317.63万~325.27

  19. Rape No-tillage Direct Seeding High-yield Culture Technique in Rice--Rape Rotation Plough Land%稻—油轮作区油菜免耕撒直播高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    姜宇龙

    2012-01-01

    总结了稻—油轮作区油菜免耕撒直播高产栽培技术,包括选种播种、合理施肥、田间管理、病虫草害防治等内容,以期为稻—油轮作区油菜免耕撒直播高产栽培提供技术参考。%Rape no-tillage direct seeding high-yield culture technique in rice-rape rotation plough land was summarized ,including seed Selection and sowing, rational application of fertilizer, disease and pest prevention and control in order to provide reference of rape no-tillage direct seeding high-yield culture in rice-rape rotation plough land.

  20. Moisture content prediction in poultry litter using artificial intelligence techniques and Monte Carlo simulation to determine the economic yield from energy use.

    Science.gov (United States)

    Rico-Contreras, José Octavio; Aguilar-Lasserre, Alberto Alfonso; Méndez-Contreras, Juan Manuel; López-Andrés, Jhony Josué; Cid-Chama, Gabriela

    2017-11-01

    The objective of this study is to determine the economic return of poultry litter combustion in boilers to produce bioenergy (thermal and electrical), as this biomass has a high-energy potential due to its component elements, using fuzzy logic to predict moisture and identify the high-impact variables. This is carried out using a proposed 7-stage methodology, which includes a statistical analysis of agricultural systems and practices to identify activities contributing to moisture in poultry litter (for example, broiler chicken management, number of air extractors, and avian population density), and thereby reduce moisture to increase the yield of the combustion process. Estimates of poultry litter production and heating value are made based on 4 different moisture content percentages (scenarios of 25%, 30%, 35%, and 40%), and then a risk analysis is proposed using the Monte Carlo simulation to select the best investment alternative and to estimate the environmental impact for greenhouse gas mitigation. The results show that dry poultry litter (25%) is slightly better for combustion, generating 3.20% more energy. Reducing moisture from 40% to 25% involves considerable economic investment due to the purchase of equipment to reduce moisture; thus, when calculating financial indicators, the 40% scenario is the most attractive, as it is the current scenario. Thus, this methodology proposes a technology approach based on the use of advanced tools to predict moisture and representation of the system (Monte Carlo simulation), where the variability and uncertainty of the system are accurately represented. Therefore, this methodology is considered generic for any bioenergy generation system and not just for the poultry sector, whether it uses combustion or another type of technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Mechanistic model to predict colostrum intake based on deuterium oxide dilution technique data and impact of gestation and prefarrowing diets on piglet intake and sow yield of colostrum

    DEFF Research Database (Denmark)

    Theil, Peter Kappel; Flummer, Christine; Hurley, W L

    2014-01-01

    The aims of the present study were to quantify colostrum intake (CI) of piglets using the D2O dilution technique, to develop a mechanistic model to predict CI, to compare these data with CI predicted by a previous empirical predictive model developed for bottle-fed piglets, and to study how...... were fed 1 of 4 gestation diets (n = 10 per diet) based on different fiber sources (low fiber [17%] or potato pulp, pectin residue, or sugarbeet pulp [32 to 40%]) from mating until d 108 of gestation. From d 108 of gestation until parturition, sows were fed 1 of 5 prefarrowing diets (n = 8 per diet......) varying in supplemented fat (3% animal fat, 8% coconut oil, 8% sunflower oil, 8% fish oil, or 4% fish oil + 4% octanoic acid). Sows fed diets with pectin residue or sugarbeet pulp during gestation produced colostrum with lower protein, fat, DM, and energy concentrations and higher lactose concentrations...

  2. 五优662水稻种植表现及抛秧高产栽培技术%Planting Performance and High Yield Cultivation Techniques of Wuyou 662 Rice

    Institute of Scientific and Technical Information of China (English)

    胡泽生; 胡桂英; 欧阳美友

    2015-01-01

    Planting performance of Wuyou 662 rice was elaborated,high yield cultivation techniques were summarized from timely planting,cultivating strong seedling,seedling throwing,rational fertilization,scientific water management etc,so as to provide reference.%阐述了五优662水稻的种植表现,并从适时播种、培育壮秧、抛栽、合理施肥、科学管水等方面总结了其高产栽培技术,以供参考。

  3. Effects of ridge cultivation technique on the growth and yield of cassava%粉垄技术对木薯生长发育和产量的影响

    Institute of Scientific and Technical Information of China (English)

    刘贵文; 黄樟华; 韦本辉; 莫振茂; 容林熙

    2011-01-01

    [Objective]The present study was conducted to explore a low cost-high benefit cultivation technique for cassava cultivation. [Method]Effect of two planting patterns, viz., ridge and traditional cultivation (CK) on growth and yield of cassava variety Xinxuan 4088 were observed by measuring plant height, stem diameter, length and diameter of tuber, number of tubers per plant, weight of tuber per plant and yield of tubers. [Result]The ridge cultivation technique improved stem and leaf growth of cassava at the early and middle growth stage and increase the biomass of cassava. The plants cultivated with ridge cultivation method showed 25.35, 28.70, 30.00, 44.92 and 46.69% increase in length, diameter, number of tubers per plant, weight of tubers per plant and yield of tubers, compared to CK. [Conclusion]The ridge cultivation technique enhanced the yield of cassava. The technique may be applied for commercial cassava production to ensure the supply of raw material in cassava processing enterprises and for sustainable development of cassava production.%探索木薯节本增效栽培技术,为旱地木薯节本增效栽培提供参考.对比粉垄栽培与传统整地栽培(CK)两种种植式对木薯品种新选4088茎叶生长及产量构成因素影响,并测定株高、茎径、单株叶片数、块根长度、块根直径、单株块根重和产量等.粉垄栽培木薯块根长度、块根直径、单株块根数、单株块根重和鲜块根产量分别较对照增加了25.35%、28.70%、30.00%、44.92%和46.69%.粉垄栽培技术可促进木薯前中期茎叶生长,增加木薯生物量,提高木薯产量,是促进木薯产业可持续发展一项重要措施.

  4. The High-yield Cultivation Techniques for Soft-seed Punica granatum from Tunisia%突尼斯软子石榴丰产栽培技术

    Institute of Scientific and Technical Information of China (English)

    吕中伟; 王鹏; 王东升; 刘许成; 许领军

    2009-01-01

    Through six-year examination in cultivation, the main variety soft-seed Punica granatum from Tunisia should be matched with pollinizer as the proportion of 6:1. The cultivation techniques were severely thinning blossom and fruit, pruning according to branch trait, adopting frost protection measures in the winter and so on. The soft-seed Punica granatum from Tunisia was of favorable varietal characteristics, fruit properties and economic benefits compared with other varieties. It had better market prospect and broader space for further development.%经过6年栽培试验,突尼斯软子石榴栽培上需要配置授粉树(6:1),严格疏花疏果,根据枝条特性整形修剪,冬季要采取防冻措施等.表现出良好的品种特性,果实性状、经济效益远高于其他品种,具有良好的市场前景,有很大的发展空间.

  5. Lean Management and Six-Sigma yield big gains in hospital's immediate response laboratory. Quality improvement techniques save more than $400,000.

    Science.gov (United States)

    Sunyog, Martha

    2004-01-01

    DSI Laboratories has used Lean and Six-Sigma methodologies to systematically eliminate waste and reduce variation in its hospital clinical laboratory. The net result was a savings of more than $400,000 in the first year. After mapping its process, the laboratory found that phlebotomists were submitting samples in large batches, which created an early-morning flood of specimens. Switching to single-piece workflow and distributing the workload more evenly allowed DSI to cover the same number of patients with two to three phlebotomists instead of 12. By establishing a more efficient workflow process within the laboratory, a single technologist could quickly move between stations and perform those tests that made up 80% of the work volume. New inventory management techniques reduced both excess inventory and the risk of shortages. Cost savings for the first year were: Reduced overtime spending by 60% ($78,000), Reassigned six phlebotomists for an annual savings of $160,000, 4.5 fewer technologist positions for a savings of $250,000.

  6. Large Field, High Resolution Full Field Optical Coherence Tomography: A Pre-clinical study of human breast tissue and cancer assessment

    CERN Document Server

    Assayag, Osnath; Sigal-Zafrani, Brigitte; Riben, Michael; Harms, Fabrice; Burcheri, Adriano; de Poly, Bertrand Le Conte; Boccara, Claude

    2012-01-01

    We present a benchmark pilot study in which high-resolution Full-Field Optical Coherence Tomography (FF-OCT) is used to image human breast tissue and is evaluated to assess its ability to aid the pathologist's management of intra-operative diagnoses. Our aim included evaluating the safety of FF-OCT on human tissue and determining the concordance between the images obtained with routinely prepared histopathological material. The compact device used for this study provides a 2 {\\mu}m-lateral and a 1 {\\mu}m-axial resolution, and is able to scan a 1.5cm^2 specimen in about 7 minutes. 75 breast specimens obtained from 22 patients have been imaged. Because the contrast in the images is generated by endogenous tissue components, no biological, contrast agents or specimen preparation is required. We characterized the major architectural features and tissue structures of benign breast tissue, including adipocytes, fibrous stroma, lobules and ducts. We subsequently characterized features resulting from their pathologic...

  7. Large field, high resolution full-field optical coherence tomography: a pre-clinical study of human breast tissue and cancer assessment.

    Science.gov (United States)

    Assayag, Osnath; Antoine, Martine; Sigal-Zafrani, Brigitte; Riben, Michael; Harms, Fabrice; Burcheri, Adriano; Grieve, Kate; Dalimier, Eugénie; Le Conte de Poly, Bertrand; Boccara, Claude

    2014-10-01

    We present a benchmark pilot study in which high-resolution Full-Field Optical Coherence Tomography (FF-OCT) was used to image human breast tissue and is evaluated to assess its ability to aid the pathologist's management of intra-operative diagnoses. FF-OCT imaging safety was investigated and agreement between FF-OCT and routinely prepared histopathological images was evaluated. The compact setup used for this study provides 1 mm3 resolution and 200 mm imaging depth, and a 2.25 cm2 specimen is scanned in about 7 minutes. 75 breast specimens were imaged from 22 patients (21 women, 1 man) with a mean age of 58 (range: 25-83). Pathologists blind diagnosed normal/benign or malignant tissue based on FF-OCT images alone, diagnosis from histopathology followed for comparison. The contrast in the FF-OCT images is generated by intrinsic tissue scattering properties, meaning that no tissue staining or preparation is required. Major architectural features and tissue structures of benign breast tissue, including adipocytes, fibrous stroma, lobules and ducts were characterized. Subsequently, features resulting from pathological modification were characterized and a diagnosis decision tree was developed. Using FF-OCT images, two breast pathologists were able to distinguish normal/benign tissue from lesional with a sensitivity of 94% and 90%, and specificity of 75% and 79% respectively.

  8. Diagnostic performance of digital breast tomosynthesis with a wide scan angle compared to full-field digital mammography for the detection and characterization of microcalcifications.

    Science.gov (United States)

    Clauser, Paola; Nagl, Georg; Helbich, Thomas H; Pinker-Domenig, Katja; Weber, Michael; Kapetas, Panagiotis; Bernathova, Maria; Baltzer, Pascal A T

    2016-12-01

    To assess the diagnostic performance of digital breast tomosynthesis (DBT), with a wide scan-angle, compared to full-field digital mammography (FFDM), for the detection and characterization of microcalcifications. IRB approval was obtained for this retrospective study. We selected 150 FFDM and DBT (50 benign and 50 malignant histologically verified microcalcifications, 50 cases classified as BI-RADS 1). Four radiologists evaluated, in separate sessions and blinded to patients' history and histology, the presence of microcalcifications. Cases with microcalcifications were assessed for visibility, characteristics, and grade of suspicion using BI-RADS categories. Detection rate and diagnostic performance were calculated. Visibility, lesions' characteristics and reading time were analysed. Detection rate and visibility were good for both FFDM and DBT, without intra-reader differences (P=0.510). Inter-reader differences were detected (PReading time for DBT was almost twice that for FFDM (44 and 25s, respectively). Wide scan-angle DBT enabled the detection and characterization of microcalcifications with no significant differences from FFDM. Inter-reader variability was seen. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  9. Prospective trial comparing full-field digital mammography (FFDM) versus combined FFDM and tomosynthesis in a population-based screening programme using independent double reading with arbitration.

    Science.gov (United States)

    Skaane, Per; Bandos, Andriy I; Gullien, Randi; Eben, Ellen B; Ekseth, Ulrika; Haakenaasen, Unni; Izadi, Mina; Jebsen, Ingvild N; Jahr, Gunnar; Krager, Mona; Hofvind, Solveig

    2013-08-01

    To compare double readings when interpreting full field digital mammography (2D) and tomosynthesis (3D) during mammographic screening. A prospective, Ethical Committee approved screening study is underway. During the first year 12,621 consenting women underwent both 2D and 3D imaging. Each examination was independently interpreted by four radiologists under four reading modes: Arm A-2D; Arm B-2D + CAD; Arm C-2D + 3D; Arm D-synthesised 2D + 3D. Examinations with a positive score by at least one reader were discussed at an arbitration meeting before a final management decision. Paired double reading of 2D (Arm A + B) and 2D + 3D (Arm C + D) were analysed. Performance measures were compared using generalised linear mixed models, accounting for inter-reader performance heterogeneity (P reading radiologists detected 27 additional invasive cancers (P reading of 2D + 3D significantly improves the cancer detection rate in mammography screening. • Tomosynthesis-based screening was successfully implemented in a large prospective screening trial. • Double reading of tomosynthesis-based examinations significantly reduced false-positive interpretations. • Double reading of tomosynthesis significantly increased the detection of invasive cancers.

  10. Comparison of 5-megapixel cathode ray tube monitors and 5-megapixel liquid crystal monitors for soft-copy reading in full-field digital mammography.

    Science.gov (United States)

    Schueller, Gerd; Schueller-Weidekamm, Claudia; Pinker, Katja; Memarsadeghi, Mazda; Weber, Michael; Helbich, Thomas H

    2010-10-01

    To retrospectively compare the image quality, lesion detection, and the diagnostic efficacy of 5-megapixel (MP) cathode ray tube monitors (CRTs) and 5-MP liquid crystal display monitors (LCDs) for soft-copy reading in full-field digital mammography (FFDM). Informed consent was waived by the Institutional Review Board for the data analysis. A total of 220 cases were compared with two 5-MP (2048×2560 pixels) CRTs and two 5-MP (2048×2560 pixels) LCDs. Nine aspects of image quality (brightness, contrast, sharpness, noise, skin, fat, retromamillary space, glandular tissue, and detection of calcifications) were evaluated. In addition, the detection of breast lesions (mass, calcifications) and diagnostic efficacy, based on the BI-RADS classification, were correlated with histologic results (n=70) and follow-up (n=150). Each aspect of the image quality was rated significantly better for 5-MP LCDs (preading in FFDM, based on histologic and follow-up correlation. However, lesion detection and diagnostic efficacy are comparable to 5-MP CRTs. The interpretation of the false-negative results suggests that the characterization of breast lesions with FFDM is not defined solely by the monitors, but is strongly influenced by the radiologist. Copyright © 2009 Elsevier Ireland Ltd. All rights reserved.

  11. Computing mammographic density from a multiple regression model constructed with image-acquisition parameters from a full-field digital mammographic unit

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Lee-Jane W [Department of Preventive Medicine and Community Health, University of Texas Medical Branch, Galveston, TX 77555-1109 (United States); Nishino, Thomas K [Department of Radiology, University of Texas Medical Branch, Galveston, TX 77555-0709 (United States); Khamapirad, Tuenchit [Department of Radiology, University of Texas Medical Branch, Galveston, TX 77555-0709 (United States); Grady, James J [Department of Preventive Medicine and Community Health, University of Texas Medical Branch, Galveston, TX 77555-1109 (United States); Jr, Morton H Leonard [Department of Radiology, University of Texas Medical Branch, Galveston, TX 77555-0709 (United States); Brunder, Donald G [Department of Academic Computing/Academic Resources, University of Texas Medical Branch, Galveston, TX 77555-1035 (United States)

    2007-08-21

    Breast density (the percentage of fibroglandular tissue in the breast) has been suggested to be a useful surrogate marker for breast cancer risk. It is conventionally measured using screen-film mammographic images by a labor-intensive histogram segmentation method (HSM). We have adapted and modified the HSM for measuring breast density from raw digital mammograms acquired by full-field digital mammography. Multiple regression model analyses showed that many of the instrument parameters for acquiring the screening mammograms (e.g. breast compression thickness, radiological thickness, radiation dose, compression force, etc) and image pixel intensity statistics of the imaged breasts were strong predictors of the observed threshold values (model R{sup 2} = 0.93) and %-density (R{sup 2} = 0.84). The intra-class correlation coefficient of the %-density for duplicate images was estimated to be 0.80, using the regression model-derived threshold values, and 0.94 if estimated directly from the parameter estimates of the %-density prediction regression model. Therefore, with additional research, these mathematical models could be used to compute breast density objectively, automatically bypassing the HSM step, and could greatly facilitate breast cancer research studies.

  12. Revealing the cellular metabolism and microstructural changes in vivo in senescing Acer saccharum leaves using two-photon FLIM and full-field OCM

    Science.gov (United States)

    Chakraborty, Sandeep; Anna, Tulsi; Kuo, Wen-Chuan; Chiou, Arthur

    2016-10-01

    Seasonal as well as climate changes have immense effect on bud burst, leaf color and leaf abscission. Autumn phenology of leaves is clearly distinguishable in deciduous plant leaves where the leaf color changes from green to red (leaf senescence). In this work, two-photon fluorescence lifetime imaging microscopy (2P-FLIM) and full-field optical coherence microscopy (FF-OCM) were applied to study mitochondrial activity and microstructural changes, respectively, in the senescence of Acer saccharum (Sugar maple) leaves. Fluorescence lifetime of reduced nicotinamide adenine dinucleotide phosphate [NAD(P)H] was recorded using 2P-FLIM to quantify the cellular metabolic changes. Compared to the green leaves, the red leaves showed a 19% increase (P face sectional images at 0.8 μm axial resolutions of the green and the red color Acer saccharum leaves via FF-OCM using white light emitting diode (WLED) showed a well-defined microstructure of epicuticular waxy layer in green leaves as compared to red leaves where disintegrated microstructure was observed. Our approach can potentially be used to correlate mitochondrial activity with epicuticular microstructural changes in senescing leaves and other biological tissues.

  13. Computing mammographic density from a multiple regression model constructed with image-acquisition parameters from a full-field digital mammographic unit

    Science.gov (United States)

    Lu, Lee-Jane W.; Nishino, Thomas K.; Khamapirad, Tuenchit; Grady, James J.; Leonard, Morton H., Jr.; Brunder, Donald G.

    2007-08-01

    Breast density (the percentage of fibroglandular tissue in the breast) has been suggested to be a useful surrogate marker for breast cancer risk. It is conventionally measured using screen-film mammographic images by a labor-intensive histogram segmentation method (HSM). We have adapted and modified the HSM for measuring breast density from raw digital mammograms acquired by full-field digital mammography. Multiple regression model analyses showed that many of the instrument parameters for acquiring the screening mammograms (e.g. breast compression thickness, radiological thickness, radiation dose, compression force, etc) and image pixel intensity statistics of the imaged breasts were strong predictors of the observed threshold values (model R2 = 0.93) and %-density (R2 = 0.84). The intra-class correlation coefficient of the %-density for duplicate images was estimated to be 0.80, using the regression model-derived threshold values, and 0.94 if estimated directly from the parameter estimates of the %-density prediction regression model. Therefore, with additional research, these mathematical models could be used to compute breast density objectively, automatically bypassing the HSM step, and could greatly facilitate breast cancer research studies.

  14. Sensitivity of a direct computer-aided detection system in full-field digital mammography for detection of microcalcifications not associated with mass or architectural distortion.

    Science.gov (United States)

    Scaranelo, Anabel M; Crystal, Pavel; Bukhanov, Karina; Helbich, Thomas H

    2010-06-01

    The purpose of this study was to evaluate the sensitivity of a direct computer-aided detection (CAD) system (d-CAD) in full-field digital mammography (FFDM) for the detection of microcalcifications not associated with mass or architectural distortion. A database search of 1063 consecutive stereotactic core biopsies performed between 2002 and 2005 identified 196 patients with Breast Imaging-Reporting and Data System (BI-RADS) 4 and 5 microcalcifications not associated with mass or distortion detected exclusively by bilateral FFDM. A commercially available CAD system (Second Look, version 7.2) was retrospectively applied to the craniocaudal and mediolateral oblique views in these patients (mean age, 59 years; range, 35-84 years). Breast density, location and mammographic size of the lesion, distribution, and tumour histology were recorded and analysed by using chi(2), Fisher exact, or McNemar tests, when applicable. When using d-CAD, 71 of 74 malignant microcalcification cases (96%) and 101 of 122 benign microcalcifications (83%) were identified. There was a significant difference (P < .05) between CAD sensitivity on the craniocaudal view, 91% (68 of 75), vs CAD sensitivity on the mediolateral oblique view, 80% (60 of 75). The d-CAD sensitivity for dense breast tissue (American College of Radiology [ACR] density 3 and 4) was higher (97%) than d-CAD sensitivity (95%) for nondense tissue (ACR density 1 and 2), but the difference was not statically significant. All 28 malignant calcifications larger than 10 mm were detected by CAD, whereas the sensitivity for lesions small than or equal to 10 mm was 94%. D-CAD had a high sensitivity in the depiction of asymptomatic breast cancers, which were seen as microcalcifications on FFDM screening, with a sensitivity of d-CAD on the craniocaudal view being significantly better. All malignant microcalcifications larger than 10 mm were detected by d-CAD. Copyright 2010 Canadian Association of Radiologists. Published by Elsevier Inc

  15. Low energy mammogram obtained in contrast-enhanced digital mammography (CEDM) is comparable to routine full-field digital mammography (FFDM)

    Energy Technology Data Exchange (ETDEWEB)

    Francescone, Mark A., E-mail: maf2184@columbia.edu [Columbia University Medical Center, ColumbiaDoctors Midtown, 51 West 51st Street, Suite 300, New York, NY 10019 (United States); Jochelson, Maxine S., E-mail: jochelsm@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Dershaw, D. David, E-mail: dershawd@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Sung, Janice S., E-mail: sungj@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Hughes, Mary C., E-mail: hughesm@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Zheng, Junting, E-mail: zhengj@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Moskowitz, Chaya, E-mail: moskowc1@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States); Morris, Elizabeth A., E-mail: morrise@mskcc.org [Memorial Sloan-Kettering Cancer Center, 1275 York Avenue, New York, NY 10065 (United States)

    2014-08-15

    Purpose: Contrast enhanced digital mammography (CEDM) uses low energy and high energy exposures to produce a subtracted contrast image. It is currently performed with a standard full-field digital mammogram (FFDM). The purpose is to determine if the low energy image performed after intravenous iodine injection can replace the standard FFDM. Methods: And Materials: In an IRB approved HIPAA compatible study, low-energy CEDM images of 170 breasts in 88 women (ages 26–75; mean 50.3) undergoing evaluation for elevated risk or newly diagnosed breast cancer were compared to standard digital mammograms performed within 6 months. Technical parameters including posterior nipple line (PNL) distance, compression thickness, and compression force on the MLO projection were compared. Mammographic findings were compared qualitatively and quantitatively. Mixed linear regression using generalized estimating equation (GEE) method was performed. Intraclass correlation coefficients (ICC) with 95% confidence interval (95%CI) were estimated to assess agreement. Results: No statistical difference was found in the technical parameters compression thickness, PNL distance, compression force (p-values: 0.767, 0.947, 0.089). No difference was found in the measured size of mammographic findings (p-values 0.982–0.988). Grouped calcifications had a mean size/extent of 2.1 cm (SD 0.6) in the low-energy contrast images, and a mean size/extent of 2.2 cm (SD 0.6) in the standard digital mammogram images. Masses had a mean size of 1.8 cm (SD 0.2) in both groups. Calcifications were equally visible on both CEDM and FFDM. Conclusion: Low energy CEDM images are equivalent to standard FFDM despite the presence of intravenous iodinated contrast. Low energy CEDM images may be used for interpretation in place of the FFDM, thereby reducing patient dose.

  16. Macro and micro full field x-ray fluorescence with an X-ray pinhole camera presenting high energy and high spatial resolution.

    Science.gov (United States)

    Romano, Francesco Paolo; Caliri, Claudia; Cosentino, Luigi; Gammino, Santo; Giuntini, Lorenzo; Mascali, David; Neri, Lorenzo; Pappalardo, Lighea; Rizzo, Francesca; Taccetti, Francesco

    2014-11-01

    This work describes a tabletop (50 cm × 25 cm × 25 cm) full field X-ray pinhole camera (FF-XPC) presenting high energy- and high spatial-resolution. The FF-XPC consists of a conventional charge-coupled device (CCD) detector coupled, in a coaxial geometry, to a pinhole collimator of small diameter. The X-ray fluorescence (XRF) is induced on the samples with an external low-power X-ray tube. The use of the CCD as an energy dispersive X-ray detector was obtained by adopting a multi-image acquisition in single photon counting and by developing a processing algorithm to be applied in real-time to each of the acquired image-frames. This approach allowed the measurement of X-ray spectra with an energy resolution down to 133 eV at the reference value of 5.9 keV. The detection of the X-ray fluorescence through the pinhole-collimator allowed the two-dimensional elemental mapping of the irradiated samples. Two magnifications (M), determined by the relative sample-pinhole-CCD distances, are used in the present setup. A low value of M (equal to 0.35×) allows the macro-FF-XRF of large area samples (up to 4 × 4 cm(2)) with a spatial resolution down to 140 μm; a large magnification (M equal to 6×) is used for the micro-FF-XRF of small area samples (2.5 × 2.5 mm(2)) with a spatial resolution down to 30 μm.

  17. Prospective trial comparing full-field digital mammography (FFDM) versus combined FFDM and tomosynthesis in a population-based screening programme using independent double reading with arbitration

    Energy Technology Data Exchange (ETDEWEB)

    Skaane, Per [Oslo University Hospital, University of Oslo, Department of Radiology, Oslo (Norway); Oslo University Hospital Ullevaal, Department of Radiology, Breast Imaging Center, Oslo (Norway); Bandos, Andriy I. [University of Pittsburgh, Department of Biostatistics, Pittsburgh (United States); Gullien, Randi; Eben, Ellen B.; Haakenaasen, Unni; Izadi, Mina; Jebsen, Ingvild N.; Jahr, Gunnar; Krager, Mona [Department of Radiology, Oslo University Hospital, Oslo (Norway); Ekseth, Ulrika [Curato Roentgen Institute, Oslo (Norway); Hofvind, Solveig [The Cancer Registry, Institute of Population-based Cancer Research, Oslo (Norway)

    2013-08-15

    To compare double readings when interpreting full field digital mammography (2D) and tomosynthesis (3D) during mammographic screening. A prospective, Ethical Committee approved screening study is underway. During the first year 12,621 consenting women underwent both 2D and 3D imaging. Each examination was independently interpreted by four radiologists under four reading modes: Arm A - 2D; Arm B - 2D + CAD; Arm C - 2D + 3D; Arm D - synthesised 2D + 3D. Examinations with a positive score by at least one reader were discussed at an arbitration meeting before a final management decision. Paired double reading of 2D (Arm A + B) and 2D + 3D (Arm C + D) were analysed. Performance measures were compared using generalised linear mixed models, accounting for inter-reader performance heterogeneity (P < 0.05). Pre-arbitration false-positive scores were 10.3 % (1,286/12,501) and 8.5 % (1,057/12,501) for 2D and 2D + 3D, respectively (P < 0.001). Recall rates were 2.9 % (365/12,621) and 3.7 % (463/12,621), respectively (P = 0.005). Cancer detection was 7.1 (90/12,621) and 9.4 (119/12,621) per 1,000 examinations, respectively (30 % increase, P < 0.001); positive predictive values (detected cancer patients per 100 recalls) were 24.7 % and 25.5 %, respectively (P = 0.97). Using 2D + 3D, double-reading radiologists detected 27 additional invasive cancers (P < 0.001). Double reading of 2D + 3D significantly improves the cancer detection rate in mammography screening. (orig.)

  18. Characterization of prototype full-field breast tomosynthesis by using a CMOS array coupled with a columnar CsI(Tl) scintillator

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jae-Gu; Choi, Young-Wook; Ham, Tae-Hee [Korea Electrotechnology Research Institute, Ansan (Korea, Republic of); Park, Hye-Suk; Kim, Ye-Seul; Kim, Hee-Joung [Yonsei University, Wonju (Korea, Republic of)

    2012-02-15

    We have developed a prototype full-field digital breast tomosynthesis (DBT) system by using a complementary-metal-oxide semiconductive (CMOS) array coupled with a columnar CsI(Tl) scintillator. The imaging system consists of a matrix with an active detector area of 3072 x 3888 pixels and a pixel pitch of 74.8 μm. For tomosynthesis imaging, the X-ray tube is automatically rotated in 3 .deg. increments in the shoot mode to acquire projection images at 15 different angles over a ±21 .deg. angular range in less than 10 s. The digital detector is stationary during image acquisition. In this research, we also carried out evaluation studies to characterize the performance of the system in different operational modes designed for the DBT system, e.g., binning mode and the range of view angles, in terms of the modulation transfer function (MTF), the normalized noise power spectra (NNPS), and the detective quantum efficiency (DQE): The MTF value measured at the Nyquist frequency was 18.49%, the NNPS value at zero frequency was about 1.93 x 10{sup -5} (mm{sup 2}), and the maximum value of DQE was about 47.09% for the full resolution. For the pixel binning mode, the MTF decreased more than it did for the full resolution mode due to the increased effective pixel size. However, the full resolution mode was more sensitive to noise than the pixel binning mode. For the scan angle of the DBT system, oblique incidence of X-rays on a detector caused blurring that reduced resolution. These results seem to be promising for the use of the DBT system in potential clinical applications and will provide important information when comparisons with other DBT systems are made.

  19. Effects of well placement and intelligent completions on SAGD in a full-field thermal-numerical model for Athabasca oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Akram, F. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Schlumberger Canada Ltd., Calgary, AB (Canada)

    2008-10-15

    This paper described a simulation study conducted to compare traditional and targeted, or smart, steam assisted gravity drainage (SAGD) and cyclic steam stimulation (CSS) processes in ultra-heavy oil and bitumen reservoirs. Simulations were conducted using a Schlumberger Petrel and ECLIPSE thermal simulator. A reservoir model was used to determine steam requirements and production strategies in multiple well pairs. A fiscal model was used to evaluate SAGD project costs as well as to determine incremental costs for each completion strategy. Results of the study showed that while the efficient use of steam did not yield higher recovery rates, the expected value of the projects was improved. Process and operational controls were investigated. Strategies considered in the study included the smart completion strategy designed to target optimal steam injection areas and avoiding continuous zones of low permeability or shale barriers. Three completion designs were simulated and results were then run through the fiscal model in order to determine the financial impacts of the methods. Five year forecasts were generated for all completion designs. The smart design yielded a 5 per cent cost improvement over other designs, and yielded 442 MSTB less bitumen over the 5 year period. It was concluded that the smart design generated an incremental CAD $1.8 mm discounted cash flow at a capitalized cost of 10 per cent. 6 refs., 3 tabs., 11 figs.

  20. Research and Application of High-yield Seed Production Techniques of Hybrid Rice in Ecuador%杂交水稻在厄瓜多尔的高产制种技术研究

    Institute of Scientific and Technical Information of China (English)

    龚志明

    2011-01-01

    The key techniques of seed production of hybrid rice in Ecuador, such as performance of parents' characters, sowing method of female parent, sowing quantity of parents, CA3 dosage, were researched. The results showed that the optimum key techniques are as follows: direct sowing of female parent, sowing quantity of female parent by 45~50 kg/hm2, GA3 dosage with 600~750 g/hm2. Meanwhile, applying this experimental results in field seed production, it successfully supports the high-yield seed production technique of chinese hybrid rice in Ecuador.%对杂交水稻在厄瓜多尔制种的亲本特性表现、母本播种方式、亲本用种量、GA、用量等关键技术进行了研究,确定了采用母本直播方式、母本用种量45~50 kg/hm3、GA3适宜用量600-750 g/hm2等技术要点,并将试验成果应用于大田制种,成功配套了中国杂交水稻在厄瓜多尔的高产制种技术.

  1. MO-A-BRD-01: An Investigation of the Dynamic Response of a Novel Acousto-Optic Liquid Crystal Detector for Full-Field Transmission Ultrasound Breast Imaging

    Energy Technology Data Exchange (ETDEWEB)

    Rosenfield, J.R.; La Riviere, P.J. [The University of Chicago, Department of Radiology (United States); Sandhu, J.S. [Santec Systems Inc., Arlington Heights, IL (United States)

    2014-06-15

    Purpose: To characterize the dynamic response of a novel acousto-optic (AO) liquid crystal detector for high-resolution transmission ultrasound breast imaging. Transient and steady-state lesion contrast were investigated to identify optimal transducer settings for our prototype imaging system consistent with the FDA limits of 1 W/cm{sup 2} and 50 J/cm{sup 2} on the incident acoustic intensity and the transmitted acoustic energy flux density. Methods: We have developed a full-field transmission ultrasound breast imaging system that uses monochromatic plane-wave illumination to acquire projection images of the compressed breast. The acoustic intensity transmitted through the breast is converted into a visual image by a proprietary liquid crystal detector operating on the basis of the AO effect. The dynamic response of the AO detector in the absence of an imaged breast was recorded by a CCD camera as a function of the acoustic field intensity and the detector exposure time. Additionally, a stereotactic needle biopsy breast phantom was used to investigate the change in opaque lesion contrast with increasing exposure time for a range of incident acoustic field intensities. Results: Using transducer voltages between 0.3 V and 0.8 V and exposure times of 3 minutes, a unique one-to-one mapping of incident acoustic intensity to steady-state optical brightness in the AO detector was observed. A transfer curve mapping acoustic intensity to steady-state optical brightness shows a high-contrast region analogous to the linear portion of the Hurter-Driffield curves of radiography. Using transducer voltages between 1 V and 1.75 V and exposure times of 90 s, the lesion contrast study demonstrated increasing lesion contrast with increasing breast exposure time and acoustic field intensity. Lesion-to-background contrast on the order of 0.80 was observed. Conclusion: Maximal lesion contrast in our prototype system can be obtained using the highest acoustic field intensity and the

  2. Women's features and inter-/intra-rater agreement on mammographic density assessment in full-field digital mammograms (DDM-SPAIN).

    Science.gov (United States)

    Pérez-Gómez, Beatriz; Ruiz, Franciso; Martínez, Inmaculada; Casals, María; Miranda, Josefa; Sánchez-Contador, Carmen; Vidal, Carmen; Llobet, Rafael; Pollán, Marina; Salas, Dolores

    2012-02-01

    Measurement of mammographic density (MD), one of the leading risk factors for breast cancer, still relies on subjective assessment. However, the consistency of MD measurement in full-digital mammograms has yet to be evaluated. We studied inter- and intra-rater agreement with respect to estimation of breast density in full-digital mammograms, and tested whether any of the women's characteristics might have some influence on them. After an initial training period, three experienced radiologists estimated MD using Boyd scale in a left breast cranio-caudal mammogram of 1,431 women, recruited at three Spanish screening centres. A subgroup of 50 randomly selected images was read twice to estimate short-term intra-rater agreement. In addition, a reading of 1,428 of the images, performed 2 years before by one rater, was used to estimate long-term intra-rater agreement. Pair-wise weighted kappas with 95% bootstrap confidence intervals were calculated. Dichotomous variables were defined to identify mammograms in which any rater disagreed with other raters or with his/her own assessment, respectively. The association between disagreement and women's characteristics was tested using multivariate mixed logistic models, including centre as a random-effects term, and taking into account repeated measures when required. All quadratic-weighted kappa values for inter- and intra-rater agreement were excellent (higher than 0.80). None of the studied women's features, i.e. body mass index, brassiere size, menopause, nulliparity, lactation or current hormonal therapy, was associated with higher risk of inter- or intra-rater disagreement. However, raters differed significantly more in images that were classified in the higher-density MD categories, and disagreement in intra-rater assessment was also lower in low-density mammograms. The reliability of MD assessment in full-field digital mammograms is comparable to that for original or digitised images. The reassuring lack of association

  3. Full Field Digital Mammography (FFDM) versus CMOS Technology, Specimen Radiography System (SRS) and Tomosynthesis (DBT) - Which System Can Optimise Surgical Therapy?

    Science.gov (United States)

    Schulz-Wendtland, R; Dilbat, G; Bani, M; Fasching, P A; Heusinger, K; Lux, M P; Loehberg, C R; Brehm, B; Hammon, M; Saake, M; Dankerl, P; Jud, S M; Rauh, C; Bayer, C M; Beckmann, M W; Uder, M; Meier-Meitinger, M

    2013-05-01

    Aim: This prospective clinical study aimed to evaluate whether it would be possible to reduce the rate of re-excisions using CMOS technology, a specimen radiography system (SRS) or digital breast tomosynthesis (DBT) compared to a conventional full field digital mammography (FFDM) system. Material and Method: Between 12/2012 and 2/2013 50 patients were diagnosed with invasive breast cancer (BI-RADS™ 5). After histological verification, all patients underwent breast-conserving therapy with intraoperative imaging using 4 different systems and differing magnifications: 1. Inspiration™ (Siemens, Erlangen, Germany), amorphous selenium, tungsten source, focus 0.1 mm, resolution 85 µm pixel pitch, 8 lp/mm; 2. BioVision™ (Bioptics, Tucson, AZ, USA), CMOS technology, photodiode array, flat panel, tungsten source, focus 0.05, resolution 50 µm pixel pitch, 12 lp/mm; 3. the Trident™ specimen radiography system (SRS) (Hologic, Bedford, MA, USA), amorphous selenium, tungsten source, focus 0.05, resolution 70 µm pixel pitch, 7.1 lp/mm; 4. tomosynthesis (Siemens, Erlangen, Germany), amorphous selenium, tungsten source, focus 0.1 mm, resolution 85 µm pixel pitch, 8 lp/mm, angular range 50 degrees, 25 projections, scan time > 20 s, geometry: uniform scanning, reconstruction: filtered back projection. The 600 radiographs were prospectively shown to 3 radiologists. Results: Of the 50 patients with histologically proven breast cancer (BI-RADS™ 6), 39 patients required no further surgical therapy (re-excision) after breast-conserving surgery. A retrospective analysis (n = 11) showed a significant (p < 0.05) increase of sensitivity with the BioVision™, the Trident™ and tomosynthesis compared to the Inspiration™ at a magnification of 1.0 : 2.0 or 1.0 : 1.0 (tomosynthesis) (2.6, 3.3 or 3.6 %), i.e. re-excision would not have been necessary in 2, 3 or 4 patients, respectively, compared to findings obtained with a standard

  4. Estudo normativo do eletrorretinograma de campo total em adultos jovens Normative values for full-field electroretinogram in healthy young adults

    Directory of Open Access Journals (Sweden)

    Josenilson Martins Pereira

    2003-01-01

    Full Text Available OBJETIVOS: A proposta deste estudo é estabelecer valores normativos para o eletrorretinograma (ERG de campo total, em um grupo de voluntários adultos jovens segundo o protocolo padrão recomendado pela Sociedade Internacional de Eletrofisiologia Visual Clínica (ISCEV. MÉTODOS: Participaram deste estudo 42 voluntários normais com idades variando de 15 a 26 anos, sendo 20 homens e 22 mulheres. Os eletrorretinogramas de campo total foram obtidos com eletrodos de lente de contato bipolares e seguiram as 5 etapas do protocolo da Sociedade Internacional de Eletrofisiologia Visual Clinica: a resposta de bastonetes; b reposta máxima; c potenciais oscilatórios; d resposta máxima de cones; e resposta de cones ao flicker 30 Hz. Os parâmetros analisados foram a amplitude de resposta do pico da onda-a até o pico da onda-b (pico a pico em miV e o tempo de culminação da onda-b (ms. RESULTADOS: As médias (± 1 desvio padrão da amplitude pico a pico foram: resposta de bastonetes - 241,1 ± 66,9 µV; resposta máxima - 385,4 ± 71,8 µV; potenciais oscilatórios - 180,6 ± 48,6 µV; resposta de cones -102,8 ± 36,3 µV e flicker 30 Hz - 69,2 ± 26,6 µV. Para o tempo implícito da onda-b os valores foram: resposta de bastonetes - 85,2 ± 7,6 ms; resposta máxima -45,6 ± 2,0ms; resposta de cones - 27,8 ± 1,2ms e flicker 30 Hz - 27,9 ± 1,2 ms. Os resultados foram comparáveis entre os grupos masculino e feminino, exceto para a resposta máxima em que as mulheres obtiveram amplitudes estatisticamente maiores (t=2,06; P=0,046. CONCLUSÃO: Os valores encontrados estão de acordo com dados normativos da literatura e são fundamentais para o diagnóstico correto de disfunções retinianas em pacientes na mesma faixa etária. Inclusão de outras faixas etárias e o aumento no número de sujeitos testados são necessários para estender valores normativos para o eletrorretinograma.PURPOSE: To determine normative data for full-field electroretinogram (ERG

  5. Padronização do eletrorretinograma de campo total em cães Full field electrorretinogram standartization in dogs

    Directory of Open Access Journals (Sweden)

    Angélica M.V. Safatle

    2010-09-01

    ável quando se objetiva comparar resultados de laboratórios distintos. A confiabilidade e reprodutibilidade deste protocolo foi demonstrada com a obtenção de registros de ótima qualidade utilizando protocolo padrão da ISCEV, eletrorretinógrafo Veris, Ganzfeld e eletrodos Burian Allen nos cães submetidos à sedação.Electroretinogram (ERG is an objective non invasive diagnostic method to evaluate retinal function which permits the early detection of lesions at retinal external layers, even before the appearance of clinical signs. In dogs, ERG is mostly utilized for preoperative evaluation in patients presenting cataracts; characterization of disturbances causing blindness, among the utilization of dogs as animal models in scientific research. Several factors interfere in ERG responses, such as the ERG machine, light stimulation, electrode, time spent on dark adaptation, pupil size, means opacity, sedation or anesthetization, species, breed and age. The purpose of this study was to standardize the full field ERG in sedated dogs, according to the International Society for Clinical Electrophysiology of Vision (ISCEV protocol, using Ganzfeld and bipolar electrodes. Two hundred thirty threes ERGs were performed in 147 female and 86 male with ages from 1 to 14 years old. Among those 233 dogs, 100 presented cataracts in different stages of maturation, 72 were diabetic and presented mature or hypermature cataracts, 26 presented ERG compatible to progressive retinal degeneration, 3 presented ERG compatible to sudden acquired retinal degeneration syndrome; for 32 dogs no abnormal ERG was registered and they were considered as having normal retinal function. Sedation was capable to induce a good immobilization with no bulb rotation, resulting uniform retinal stimulation, using Ganzfeld. Veris system successfully registered all 5 ISCEV responses, simultaneously from both eyes, at the same time. Full field ERG became a fundamental ophthalmic exam, then, its standardization is

  6. 甜叶菊“皖甜1号”高产栽培优化研究1)%Study on High-yield Cultivating Technique Optimization for Stevia rebaudiana Bertoni “Wantian No .1”

    Institute of Scientific and Technical Information of China (English)

    张子学; 王其斌; 尹玉柱; 林平

    2013-01-01

      为提高甜叶菊的栽培技术水平、揭示密度、氮、钾肥施用量与产量的关系.采用二次通用旋转组合设计的方法,建立各因素与产量之间的回归方程,筛选高产栽培优化模式.结果表明:最佳农艺方案:种植密度153.480~173.700千株/hm2,配施纯氮285.225~331.225kg/hm2和 K2 O 299.775~327.000kg /hm 2产量可达4860.00kg/hm 2以上.%The common quadratic regression combination design was used to Raise the level of cul-tivation techniques and study quantity relation between yield and main cul-tivating factors ( the density and amount of N and K ) in Stevia rebaudiana Bertoni .The regression equation of the main factors and yield were established and cultivation optimization mode were filtered .The re-sults showed that the optimum agronomic project the high yield ( more than 4860 .00 kg/hm 2 ) were the planting density153 .480-173 .700 plants ,amount of N of 285 .225-331 .225 kg/hm 2 ,K2 O 299 .775-327 .000 kg/hm 2 .

  7. 节水抗旱稻新组合“旱优73”高产制种技术%High yield seed production techniques of water saving and drought resistance rice combination“Hanyou 73”

    Institute of Scientific and Technical Information of China (English)

    兰有明

    2015-01-01

    旱优73是籼型三系节水抗旱稻新组合,具有节水抗旱、抗性强、米质优、适应性广等特点。根据近几年对其亲本的观察和制种实践,总结该组合的高产制种技术。%“Hanyou 73”is a new water saving and drought resistance combination of three line Indica rice,showing water saving and drought resistance,high resistance to diseases,high quality and good adaptability. This paper sum-marized its high yield seed production techniques based on observation on its parents and practice in seed production in recent years.

  8. 越夏辣椒高产栽培技术及主要病虫害防治研究%Study on High Yield Cultivation Techniques and Main Pests Control of Summering Pepper

    Institute of Scientific and Technical Information of China (English)

    黄正勤; 宋元周; 杨自保

    2014-01-01

    从选择抗病品种、培育壮苗、定植及定植后管理等方面介绍了越夏辣椒高产栽培管理技术,并对辣椒主要病虫害防治方法进行了阐述,为辣椒生产提供了技术借鉴。%The high yield cultivation techniques and main pests control of summering pepper were introduced from the following aspects, including choosing resistant varieties, nurturing seedlings, planting and post-planting management. Moreover, the main methods for controlling pests and diseases were elaborated. The results provided technical references for pepper production.

  9. 杂交稻元丰优86在永定种植表现及高产栽培技术%Planting Performance and High-yielding Cultivation Techniques of Hybrid Rice Combination Yuanfengyou 86 in Yongding Country

    Institute of Scientific and Technical Information of China (English)

    游梅兰

    2014-01-01

    Yuanfengyou 86, derived from the CMS line Yuanfeng A and a restorer line Minghui 86, was a new hybrid rice combination. Yuanfengyou 86 was registered and released for commercial production by National Crop Variety Appraisal Committee in Fujian province in 2011. During the year of 2012-1013, Yuanfengyou 86 was introduced and planted in Yongding county of Fujian province. In this paper, we introduced planting performance and high-yielding cultivation techniques of Yuanfengyou 86.%元丰优86是用元丰A×明恢86配组育成的三系杂交稻新品种,2011年通过福建省品种审定。2012—2013年在永定县仙师乡示范种植,掌握其特征特性和高产栽培技术。

  10. 台中11号荷兰豆无公害高产栽培技术%Pollution-free and High-yield Cultivation Techniques of Taichung11

    Institute of Scientific and Technical Information of China (English)

    吴开通

    2011-01-01

    荷兰豆是厦门市同安区主要蔬菜品种和出口农产品之一。该文总结了当地主栽品种———台中11号从秋冬茬至早春茬的无公害高产栽培技术。%Snow bean(Pisum sativum) was one of the major vegetable varieties and agricultural exports at Tongan District,Xiamen City,Fujian Province.This paper dealt with the main local snow bean cultivar Taichung11,and concluded the pollution-free and high-yield cultivation techniques from autumn-winter season to early-spring season.

  11. Planting Performance and High-yielding Cultivation Techniques of Hybrid Rice Combination Yiyou 673 in Anxi Country%优质超级稻宜优673在安溪种植表现及高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    肖全省

    2014-01-01

    Yiyou 673, derived from the CMS line Yixiang 1A and a restorer line Fuhui 673, was a new hybrid rice combination developed by Rice Research Institute, Fujian Academy of Agricultural Sciences. It was registered and released in 2006 in Fujian province. Yiyou 673 was introduced and planted in Anxi county of Fujian province for extensive adaptability, rice quality, high and stable yield. In this paper, we introduced planting performance and high-yielding cultivation techniques of Yiyou 673.%宜优673是福建省农业科学院水稻研究所用不育系宜香1A与恢复系福恢673配组而成的三系杂交水稻品种,于2006年通过福建省品种审定。在安溪县种植表现丰产、稳产、米质优、后期转色好等特点。介绍了宜优673在安溪县种植表现及高产栽培技术。

  12. Planting Performance and High-yielding Cultivation Techniques for Hybrid Rice Combination Shenliangyou 862 at Yong,an City%深两优862在永安市种植表现与高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    林增贵

    2016-01-01

    深两优862是由江苏明天种业科技有限公司、南昌穗民农业科技有限公司、临湘市兆农科技研发中心,用深08S与R5662配组育成的杂交水稻新品种。具有长势旺,分蘖力强,成穗率高,有效穗多,高产稳产,米质优等特点。介绍深两优862在永安市种植表现与高产栽培技术。%A new hybrid rice combination Shenliangyou 862 derived from the cross of a sterile line Shen 08S and a restorer line R5662 was developed by Jiangsu Mingtian Seed Science and Technology Co., Ltd, Nan-chang Suimin Agricultural Science and Technology Co., Ltd and Linxiang Zhaonong Science and Technology Research and Development Center. It showed the characteristics of vigorous growth, strong tillering ability, high earbearing tiller percentage, more effective panicle number, high and stable yield, and good quality. Planting performance and high-yielding cultivation techniques for Shenliangyou 862 at Yong,an city was in-troduced in this paper.

  13. Yield enhancement with DFM

    Science.gov (United States)

    Paek, Seung Weon; Kang, Jae Hyun; Ha, Naya; Kim, Byung-Moo; Jang, Dae-Hyun; Jeon, Junsu; Kim, DaeWook; Chung, Kun Young; Yu, Sung-eun; Park, Joo Hyun; Bae, SangMin; Song, DongSup; Noh, WooYoung; Kim, YoungDuck; Song, HyunSeok; Choi, HungBok; Kim, Kee Sup; Choi, Kyu-Myung; Choi, Woonhyuk; Jeon, JoongWon; Lee, JinWoo; Kim, Ki-Su; Park, SeongHo; Chung, No-Young; Lee, KangDuck; Hong, YoungKi; Kim, BongSeok

    2012-03-01

    A set of design for manufacturing (DFM) techniques have been developed and applied to 45nm, 32nm and 28nm logic process technologies. A noble technology combined a number of potential confliction of DFM techniques into a comprehensive solution. These techniques work in three phases for design optimization and one phase for silicon diagnostics. In the DFM prevention phase, foundation IP such as standard cells, IO, and memory and P&R tech file are optimized. In the DFM solution phase, which happens during ECO step, auto fixing of process weak patterns and advanced RC extraction are performed. In the DFM polishing phase, post-layout tuning is done to improve manufacturability. DFM analysis enables prioritization of random and systematic failures. The DFM technique presented in this paper has been silicon-proven with three successful tape-outs in Samsung 32nm processes; about 5% improvement in yield was achieved without any notable side effects. Visual inspection of silicon also confirmed the positive effect of the DFM techniques.

  14. Early experience in the use of quantitative image quality measurements for the quality assurance of full field digital mammography x-ray systems

    Science.gov (United States)

    Marshall, N. W.

    2007-09-01

    Quantitative image quality results in the form of the modulation transfer function (MTF), normalized noise power spectrum (NNPS) and detective quantum efficiency (DQE) are presented for nine full field digital mammography (FFDM) systems. These parameters are routinely measured as part of the quality assurance (QA) programme for the seven FFDM units covered by our centre. Just one additional image is required compared to the standard FFDM protocol; this is the image of an edge, from which the MTF is calculated. A variance image is formed from one of the flood images used to measure the detector response and this provides useful information on the condition of the detector with respect to artefacts. Finally, the NNPS is calculated from the flood image acquired at a target detector air kerma (DAK) of 100 µGy. DQE is then estimated from these data; however, no correction is currently made for effects of detector cover transmission on DQE. The coefficient of variation (cov) of the 50% point of the MTF for five successive MTF results was 1%, while the cov for the 50% MTF point for an a-Se system over a period of 17 months was approximately 3%. For four a-Se based systems, the cov for the NNPS at 1 mm-1 for a target DAK of 100 µGy was approximately 4%; the same result was found for four CsI based FFDM units. With regard to the stability of NNPS over time, the cov for four NNPS results acquired over a period of 12 months was also approximately 4%. The effect of acquisition geometry on NNPS was also assessed for a CsI based system. NNPS data acquired with the antiscatter grid in place showed increased noise at low spatial frequency; this effect was more severe as DAK increased. DQE results for the three detector types (a-Se, CsI and CR) are presented as a function of DAK. Some reduction in DQE was found for both the a-Se and CsI based systems at a target DAK of 12.5 µGy when compared to DQE data acquired at 100 µGy. For the CsI based systems, DQE at 1 mm-1 fell from 0

  15. Full-field linear and nonlinear measurements using Continuous-Scan Laser Doppler Vibrometry and high speed Three-Dimensional Digital Image Correlation

    Science.gov (United States)

    Ehrhardt, David A.; Allen, Matthew S.; Yang, Shifei; Beberniss, Timothy J.

    2017-03-01

    Spatially detailed dynamic measurements of thin, lightweight structures can be difficult to obtain due to the structure's low mass and complicated deformations under certain loading conditions. If traditional contacting sensors, such as accelerometers, strain gauges, displacement transducers, etc., are used, the total number of measurement locations available is limited by the weight added and the effect each sensor has on the local stiffness of the contact area. Other non-contacting sensors, such as Laser Doppler Vibrometers (LDV), laser triangulation sensors, proximity sensors, etc., do not affect the dynamics of a structure, but are limited to single point measurements. In contrast, a few recently developed non-contacting measurement techniques have been shown to be capable of simultaneously measuring the response over a wide measurement field. Two techniques are considered here: Continuous-Scan Laser Doppler Vibrometry (CSLDV) and high speed Three-Dimensional Digital Image Correlation (3D DIC). With the use of these techniques, unprecedented measurement resolution can be achieved. In this work, the linear and nonlinear deformations of a clamped, nominally flat beam and plate under steady state sinusoidal loading will be measured using both techniques. In order to assess their relative merits, the linear natural frequencies, mode shapes, and nonlinear deformation shapes measured with each method are compared. Both measurement systems give comparable results in many cases, although 3D DIC is more accurate for spatially complex deformations at large amplitudes and CSLDV is more accurate at low amplitudes and when the spatial deformation pattern is simpler.

  16. Study on Fertilizer Application and Yield Model of‘Yongyou 12’and Its Fertilization Techniques in Super-high-yielding Cultivation Single Cropping Rice%‘甬优12’施肥量与产量关系模型及超高产栽培施肥技术研究

    Institute of Scientific and Technical Information of China (English)

    蔡建军; 汪恩国; 林采舜; 何杰

    2015-01-01

    为了探明超级杂交稻‘甬优12’产量与施肥量关系,揭示其单季稻超高产栽培需肥规律,提升整体施肥技术水平,在统一栽培技术措施下测土配方施肥,跟踪调查2012—2013年12个示范方不同施肥组合及施肥量,以专家组实割实收考查产量的方法,对单季稻‘甬优12’施肥量与产量关系及超高产栽培施肥技术进行研究。结果表明,在土壤肥力水平中等的情况下,单季晚稻‘甬优12’产量(Y)随施肥量(有机肥F和N、P、K)增加而递升且呈幂次函数(近似线性)递升,其关系模型为:Y=0.00003F2-0.2963F+11302(Y=0.2301F+9258),Y=0.0504N2+24.566N+1953(Y=51.243N-1543),Y=0.0361P2+26.596P+8707(Y=34.143P+8358),Y=0.0208K2+7.4996K+8499(Y=17.793K+7306)。由此提出,11000~12000 kg/hm2目标产量为投入农家有机肥8000~12000 kg/hm2、纯N量245~265 kg/hm2、P2O5量75~105 kg/hm2、K2O量210~265 kg/hm2,N:P:K比例1.00:0.35:0.93;目标产量15000 kg/hm2为投入农家有机肥15000~20000 kg/hm2、纯N量320 kg/hm2、P2O5量190 kg/hm2、K2O量410 kg/hm2,N:P:K比例1.00:0.59:1.28。后者生产成本大幅度提高,生产风险大幅度上升,需集成超级栽培、肥料运筹、病虫防治、水桨管理等一系列协调促进,才能实现预期目标。%The relationship between fertilization level and yield of‘Yongyou 12’and the technique of fertilization for super high yield cultivation were studied in this research. Fertilization was conducted according to the soil fertile level under the unified cultivation technology. Follow up investigation was carried out of 12 demonstrations of different fertilizer combinations and the amount of fertilizer from 2012 to 2013. The rice yield was examined by the experts harvesting. Our data serve as a useful tool for elucidating the relationship between fertilization level and yield of‘Yongyou 12’and its fertilization techniques in super-high-yielding

  17. Low-Yield Cigarettes

    Science.gov (United States)

    ... Program Division of Reproductive Health More CDC Sites Low-Yield Cigarettes Recommend on Facebook Tweet Share Compartir ... they compensate when smoking them. Smokers Who Use Low-Yield Cigarettes Many smokers consider smoking low-yield ...

  18. Three-dimensional shear wave imaging based on full-field laser speckle contrast imaging with one-dimensional mechanical scanning.

    Science.gov (United States)

    Chao, Pei-Yu; Li, Pai-Chi

    2016-08-22

    The high imaging resolution and motion sensitivity of optical-based shear wave detection has made it an attractive technique in biomechanics studies with potential for improving the capabilities of shear wave elasticity imaging. In this study we implemented laser speckle contrast imaging for two-dimensional (X-Z) tracking of transient shear wave propagation in agarose phantoms. The mechanical disturbances induced by the propagation of the shear wave caused temporal and spatial fluctuations in the local speckle pattern, which manifested as local blurring. By mechanically moving the sample in the third dimension (Y), and performing two-dimensional shear wave imaging at every scan position, the three-dimensional shear wave velocity distribution of the phantom could be reconstructed. Based on comparisons with the reference shear wave velocity measurements obtained using a commercial ultrasound shear wave imaging system, the developed system can estimate the shear wave velocity with an error of less than 6% for homogeneous phantoms with shear moduli ranging from 1.52 kPa to 7.99 kPa. The imaging sensitivity of our system makes it capable of measuring small variations in shear modulus; the estimated standard deviation of the shear modulus was found to be less than 0.07 kPa. A submillimeter spatial resolution for three-dimensional shear wave imaging has been achieved, as demonstrated by the ability to detect a 1-mm-thick stiff plate embedded inside heterogeneous agarose phantoms.

  19. Elemental mapping in a contemporary miniature by full-field X-ray fluorescence imaging with gaseous detector vs. scanning X-ray fluorescence imaging with polycapillary optics

    Science.gov (United States)

    Silva, A. L. M.; Cirino, S.; Carvalho, M. L.; Manso, M.; Pessanha, S.; Azevedo, C. D. R.; Carramate, L. F. N. D.; Santos, J. P.; Guerra, M.; Veloso, J. F. C. A.

    2017-03-01

    Energy dispersive X-ray imaging can be used in several research fields and industrial applications. Elemental mapping through energy dispersive X-ray imaging technique has become a promising method to obtain positional distribution of specific elements in a non-destructive way. To obtain the elemental distribution of a sample it is necessary to use instruments capable of providing a precise positioning together with a good energy resolution. Polycapillary beams together with silicon drift chamber detectors are used in several commercial systems and are considered state-of-the-art spectrometers, however they are usually very costly. A new concept of large energy dispersive X-ray imaging systems based on gaseous radiation detectors emerged in the last years enabling a promising 2D elemental detection at a very reduced price. The main goal of this work is to analyze a contemporary Indian miniature with both X-ray fluorescence imaging systems, the one based on a gaseous detector 2D-THCOBRA and the state-of-the-art spectrometer M4 Tornado, from Bruker. The performance of both systems is compared and evaluated in the context of the sample's analysis.

  20. Afforestation Techniques and Result Analysis of Fast-growing and High-yield Forests of Cunninghamia lanceolata%青阳县杉木速生丰产林营林技术与成效分析

    Institute of Scientific and Technical Information of China (English)

    姜建军

    2012-01-01

    In this paper the demonstration forests of Cunninghamia laneeolata planted in 2004 in Nanhe Village, Muzhen Township of Qingyang County were selected as the example and the effects of technique application in fast-growing and high-yield forests of Cunning- hamia lanceolata on the stand quality and timber production were analyzed. The results showed that by adopting intensive management measures including careful tillage, fine variety and strong stock, careful planting, management and protection, etc., the average height, DBH, basal diameter and stand volume of the demonstration forests have increased significantly and brought remarkable benefits compared with stands with the same site conditions and general afforestation measures.%本文以青阳县木镇镇南河村2004年营造杉木示范林为例,分析杉木速生丰产用材林营林技术措施对林分质量和木材产量的影响。结果表明:示范点林分通过采取细致整地、良种壮苗、认真栽植、精心管护等集约经营措施,比同等立地条件对照造林林分的平均高、平均地(胸)径、林木蓄积量均有明显提高,效益明显。

  1. Planting Performance and Super High Yield Cultivation Techniques of Yongyou 2640 with Bowl Seedling and Mechanical Transplanting%甬优2640种植表现及钵育机插超高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    於永杰; 李华; 夏龙珠; 钱宗华

    2014-01-01

    引种示范和钵育机插超高产攻关试验表明,甬优2640具有熟期早、熟相好、穗型大、株型好、高温条件下结实率稳定等生育特性。本文研究并总结了甬优2640钵育机插超高产栽培技术要点:培育壮秧、精确机插、精确定量施肥、定量水浆调控、加强病虫防治,以期为甬优2640的推广应用及钵育机插超高产栽培提供借鉴。%Introduction and demonstration showed that Yongyou 2640 has the performance of early maturity, good color, big panicle, good plant type and stability in seed setting rate. The paper summarized the super high yield cultivation techniques of Yongyou 2640 with bowl seedling and mechanical transplanting, such as cultivating strong seedlings, precise mechannical transplanting, precise quantitative fertilization, water regulation and strengthening pest control.

  2. Fission yield measurements at IGISOL

    Directory of Open Access Journals (Sweden)

    Lantz M.

    2016-01-01

    Full Text Available The fission product yields are an important characteristic of the fission process. In fundamental physics, knowledge of the yield distributions is needed to better understand the fission process. For nuclear energy applications good knowledge of neutroninduced fission-product yields is important for the safe and efficient operation of nuclear power plants. With the Ion Guide Isotope Separator On-Line (IGISOL technique, products of nuclear reactions are stopped in a buffer gas and then extracted and separated by mass. Thanks to the high resolving power of the JYFLTRAP Penning trap, at University of Jyväskylä, fission products can be isobarically separated, making it possible to measure relative independent fission yields. In some cases it is even possible to resolve isomeric states from the ground state, permitting measurements of isomeric yield ratios. So far the reactions U(p,f and Th(p,f have been studied using the IGISOL-JYFLTRAP facility. Recently, a neutron converter target has been developed utilizing the Be(p,xn reaction. We here present the IGISOL-technique for fission yield measurements and some of the results from the measurements on proton induced fission. We also present the development of the neutron converter target, the characterization of the neutron field and the first tests with neutron-induced fission.

  3. 不同耕作和种植方式对稻田杂草及水稻产量的影响%Effects of Crop Establishment Techniques on Weeds and Rice Yield

    Institute of Scientific and Technical Information of China (English)

    Rajender Singh Chhokar[著; 禹盛苗(译)

    2016-01-01

    Field and pot studies were conducted to evaluate the effects of seven rice establishment techniques [puddling transplanting (PT), no tillage transplanting (NTT), puddling drum wet seeding (PDWS), no tillage drum wet seeding (NTDWS), conventional tillage dry drilling(CTDD), furrow irrigated raised beds system dry drilling(FIRBSDD), and no-tillage dry-drilling(NTDD)] and water submergence stress on weeds and rice yield. The highest yield and least weed abundance were in the PT treatment. The direct seeded rice (DSR), both dry and wet exhibited severe weed infestation, and compared to transplanting showed reduced yield both in the presence and absence of weeds. The yield losses due to weeds in the DSR treatments ranged from 91.4 to 99.0%, compared to 16.0 and 42.0% in the transplanting treatments (PT and NTT). Weeds, including Cyperus rotundus L., Dactyloctenium aegyptium (L.) Willd., Digera arvensis Forsk., Phyllanthus niruri L., and Trianthema portulacastrum L, which were found in the un-puddled DSR treatments were absent in the puddled plots, particularly the PT treatments. In farmer's field studies, when compared to the PT treatments, the DSR treatments exhibited lower yields(15.8%) with coarse varieties(HKR-47&IR-64), but fine cultivars(Sharbati&PB-1) exhibited similar yields under both systems. In view of the shortage of labour for manual transplanting, there is a need to de-velop suitable cultivars for aerobic system conditions(unpuddled DSR and NT machine-transplanting).%采用田间试验,研究了7种不同水稻耕作和种植方式[水田翻耕移栽(puddling transplanting, PT)、免耕移栽(no tillage transplanting, NTT)、水田翻耕滚筒湿播(puddling drum wet seeding, PDWS)、免耕滚筒湿播(no tillage drum wet seeding, NTDWS)、传统耕作旱穴播(conventional tillage dry drilling, CTDD)、沟垄灌溉旱穴播(furrow irrigat-ed raised beds system dry drilling, FIRBSDD)和免耕旱穴播(no-tillage dry

  4. A Generalized Yield Criterion

    Institute of Scientific and Technical Information of China (English)

    Shijian YUAN; Dazhi XIAO; Zhubin HE

    2004-01-01

    A generalized yield criterion is proposed based on the metal plastic deformation mechanics and the fundamental formula in theory of plasticity. Using the generalized yield criterion, the reason is explained that Mises yield criterion and Tresca yield criterion do not completely match with experimental data. It has been shown that the yield criteria of ductile metals depend not only on the quadratic invariant of the deviatoric stress tensor J2, but also on the cubic invariant of the deviatoric stress tensor J3 and the ratio of the yield stress in pure shear to the yield stress in uniaxial tension k/σs. The reason that Mises yield criterion and Tresca yield criterion are not in good agreement with the experimental data is that the effect of J3 and k/σs is neglected.

  5. Yield stress fluids slowly yield to analysis

    NARCIS (Netherlands)

    Bonn, D.; Denn, M.M.

    2009-01-01

    We are surrounded in everyday life by yield stress fluids: materials that behave as solids under small stresses but flow like liquids beyond a critical stress. For example, paint must flow under the brush, but remain fixed in a vertical film despite the force of gravity. Food products (such as mayon

  6. New techniques in digital holography

    CERN Document Server

    Picart, Pascal

    2015-01-01

    A state of the art presentation of important advances in the field of digital holography, detailing advances related to fundamentals of digital holography, in-line holography applied to fluid mechanics, digital color holography, digital holographic microscopy, infrared holography, special techniques in full field vibrometry and inverse problems in digital holography

  7. minimum variance estimation of yield parameters of rubber tree with ...

    African Journals Online (AJOL)

    2013-03-01

    Mar 1, 2013 ... STAMP, an OxMetric modular software system for time series analysis, was used to estimate the yield ... derlying regression techniques. .... Kalman Filter Minimum Variance Estimation of Rubber Tree Yield Parameters. 83.

  8. Main Cultivation Techniques of New Corn Variety Weike 702 in High Yield Creation in Suiyang District of Shangqiu City%玉米新品种伟科702在商丘市睢阳区高产创建中的主要栽培技术

    Institute of Scientific and Technical Information of China (English)

    王德珍; 卢广远

    2015-01-01

    Technology roadmap of high yield create for new corn variety Weike 702 in Suiyang District of Shangqiu City was introduced,and the main cultivation techniques were summarized,including mechanized single particle precision planting technique,chemical regulation technology,delayed harvest technology etc.,so as to provide technical basis for high yield create of corn in Henan Province.%介绍了玉米新品种伟科702在商丘市睢阳区高产创建的技术路线,并总结了主要栽培技术,如机械化单粒精播技术、化学调控技术、延时晚收技术等,为河南省玉米高产创建提供技术依据。

  9. YIELD OF AMARANTH

    African Journals Online (AJOL)

    department of Agricultural Engineering, University of Ibadan, Nigeria. (Received 28 ... properties, growth and shoot yield of large-green leafy amaranth (Amaranth sp.). Soil moisture ... microorganisms which stimulate the physical processes ... to plants and, consequently, crop establishment ... sustainable soil structure.

  10. 6 Grain Yield

    African Journals Online (AJOL)

    evaluate new interspecific genotypes for intensified double cropping of irrigated rice. The experimental ... the performance of the new irrigated .... nursing at a spacing of 20 cm between plants ..... if new technologies, comprising high yielding.

  11. Comparison of two different suture-passing techniques with different suture materials and thicknesses: Biomechanical study of flexor tendons for yield points, gap formation and early post-operative status

    Directory of Open Access Journals (Sweden)

    Volkan Ergan

    2016-12-01

    Conclusion: The yield points with higher forces is expected to be preferred, but their thicknesses can be 3-0 or 4-0. Oblique suture passing should be preferred rather than longitudinal passing. Obviously, suture strengthening methods, like epitendineous running sutures and core sutures, should be used. Without these measures, even passive wrist motion can result in gap formation at the repair site. The results of this study showed that tensile properties of the repaired vary considerably with differences in suture material and design. [Hand Microsurg 2016; 5(3.000: 130-136

  12. Cultivation Techniques of Winter Cowpea with Quality and High Yield in Sanya Region%三亚地区冬种豇豆优质高产栽培技术

    Institute of Scientific and Technical Information of China (English)

    俞承明

    2013-01-01

      总结了三亚地区冬种豇豆优质高产栽培技术,包括选地整地、品种选择、田间管理、病虫害防治、采收等内容,以期为该地区冬种豇豆栽培提供技术参考。%In this paper, cultivation techniques on land selection, varieties, field management, pest and disease, harvest of Win-ter cowpea are summed up, and will thus assist local planters in consulting techniques service.

  13. 基于区域CORS系统的全野外数字化测图方法探讨%Discussion on full-field digital mapping systems approach regional CORS

    Institute of Scientific and Technical Information of China (English)

    郭晓良; 杜会平

    2014-01-01

    基于区域CORS系统的全野外数字化测图,可以看做是GPS RTK测图方式的升级,其测图方式更加简便快捷,完全实现单人作业,工作效率成倍提升,因此,CORS系统一出现,就受到广大用户的欢迎。文章就基于区域CORS系统的全野外数字化测图方法进行探讨。%Based on full-field digital mapping system of regional CORS, it can be seen as a way to upgrade the GPS RTK Mapping. Its mapping easier and faster way fully realized single job, efficiency increase exponentially. Therefore, CORS system appeared, they were warmly welcomed. This paper discusses digital mapping method field area CORS system.

  14. First experiments for the detection of simulated mammographic lesions. Digital full field mammography with a new detector with a double plate of pure selenium; Erste Untersuchungen zur Detektion simulierter mammographischer Laesionen. Digitale Vollfeldmammographie mit einem Doppelschicht-Selen-Detektor

    Energy Technology Data Exchange (ETDEWEB)

    Schulz-Wendtland, R.; Wenkel, E.; Adamietz, B.; Lell, M.; Anders, K.; Uder, M. [Universitaetsklinikum Erlangen, Abteilung Gynaekologische Radiologie, Radiologisches Institut, Erlangen (Germany); Hermann, K.P. [Universitaetsmedizin Goettingen, Abteilung Diagnostische Radiologie, Goettingen (Germany)

    2011-02-15

    The article describes an experimental phantom study of a system for digital full field mammography with a new digital detector with a double plate of pure selenium. The experiments were carried out with the new full field digital mammography system Amulet from FujiFilm. This system has a new detector (18 x 24 cm{sup 2}) on the basis of highly purified amorphous selenium (a-Se) with a pixel size of 50 {mu}m. The x-rays are converted into electric signals in the first plate which are read into the second plate with the help of an optical switch and demonstrated in the form of an image. In this way a better pixel size/volume and signal-to-noise ratio should be achieved. The object of the investigation was the Wisconsin Mammographic Random Phantom, Model 152 A (Technical Performance Mo/Mo, 28 kV, 100 mAs). Five investigators with different experiences in mammography each received three images on a monitor with different random positions of the simulated lesions in the phantom for assessment. The detection rates were compared under the same conditions with the results of two other full field digital mammography systems. The median detection rate for all images and investigators for the new doubled plated a-Se detector with optical switch was 98.7%. For both other systems with a-Si or and a-Se detectors the detection rate was 89.8% or 97.3%, respectively. There were no significant differences in the detection rate of the simulated breast lesions for all three systems considering the interobserver and intraobserver variation. The first phantom study for the detection of simulated breast lesions with the new full field digital mammography system Amulet demonstrates equivalent results with the other systems used in the clinical routine. The trend towards superiority of the new system has to be confirmed in further clinical studies. (orig.) [German] Im Rahmen einer Phantomstudie sollte untersucht werden, ob ein neues System zur digitalen Vollfeldmammographie, das mit einem

  15. Pilot Study on the Detection of Simulated Lesions Using a 2D and 3D Digital Full-Field Mammography System with a Newly Developed High Resolution Detector Based on Two Shifts of a-Se.

    Science.gov (United States)

    Schulz-Wendtland, R; Bani, M; Lux, M P; Schwab, S; Loehberg, C R; Jud, S M; Rauh, C; Bayer, C M; Beckmann, M W; Uder, M; Fasching, P A; Adamietz, B; Meier-Meitinger, M

    2012-05-01

    Purpose: Experimental study of a new system for digital 2D and 3D full-field mammography (FFDM) using a high resolution detector based on two shifts of a-Se. Material and Methods: Images were acquired using the new FFDM system Amulet® (FujiFilm, Tokio, Japan), an a-Se detector (receptor 24 × 30 cm(2), pixel size 50 µm, memory depth 12 bit, spatial resolution 10 lp/mm, DQE > 0.50). Integrated in the detector is a new method for data transfer, based on optical switch technology. The object of investigation was the Wisconsin Mammographic Random Phantom, Model 152A (Radiation Measurement Inc., Middleton, WI, USA) and the same parameters and exposure data (Tungsten, 100 mAs, 30 kV) were consistently used. We acquired 3 different pairs of images in the c-c and ml planes (2D) and in the c-c and c-c planes with an angle of 4 degrees (3D). Five radiologists experienced in mammography (experience ranging from 3 months to more than 5 years) analyzed the images (monitoring) which had been randomly encoded (random generator) with regard to the recognition of details such as specks of aluminum oxide (200-740 µm), nylon fibers (0.4-1.6 mm) and round lesions/masses (diameters 5-14 mm), using special linear glasses for 3D visualization, and compared the results. Results: A total of 225 correct positive decisions could be detected: we found 222 (98.7 %) correct positive results for 2D and 3D visualization in each case. Conclusion: The results of this phantom study showed the same detection rates for both 2D and 3D imaging using full field digital mammography. Our results must be confirmed in further clinical trials.

  16. 玉米浚单20在商丘市的种植表现及高产栽培技术研究%Planting Performance and High Yield Cultivation Techniques of Maize Xundan No.20 in Shangqiu City

    Institute of Scientific and Technical Information of China (English)

    袁立贺; 张军勇; 任晓雪

    2011-01-01

    浚单20是浚县农业科学研究所选育的高产、稳产、优质、多抗、广适、紧凑型中熟玉米单交种。从农艺性状、产量、品质、抗逆性、制种、适应性等方面阐述了浚单20的特征特性,并从选地、播种、肥水管理及病虫草害防治等方面总结了其高产栽培技术。%The medium maturity single cross hybrid Xundan No.20 was bred by Xunxian institute of agricultural science. This variety has the characteristics of high and stable yield, high quality, multiple resistance and wide adaptability. The characteristics of Xundan No.20 were described from six respects including agronomic characters, yield, quality, resistance, seed production and adapt. Its high cultural technologies were also summarized including choose cultivating land, sowing, nutrient and water management, pest, disease and weed prevention and so on.

  17. Statistical circuit design for yield improvement in CMOS circuits

    Science.gov (United States)

    Kamath, H. J.; Purviance, J. E.; Whitaker, S. R.

    1990-01-01

    This paper addresses the statistical design of CMOS integrated circuits for improved parametric yield. The work uses the Monte Carlo technique of circuit simulation to obtain an unbiased estimation of the yield. A simple graphical analysis tool, the yield factor histogram, is presented. The yield factor histograms are generated by a new computer program called SPICENTER. Using the yield factor histograms, the most sensitive circuit parameters are noted, and their nominal values are changed to improve the yield. Two basic CMOS example circuits, one analog and one digital, are chosen and their designs are 'centered' to illustrate the use of the yield factor histograms for statistical circuit design.

  18. Research on the Key High-yielding Cultivation Techniques of Machine-transplanted Rice%机插稻高产栽培关键技术的适宜值研究

    Institute of Scientific and Technical Information of China (English)

    李伟海; 赖清云; 金军

    2015-01-01

    以2012年常州市水稻苗情哨田块的多点苗情监测数据为样本,分析归纳了种植方式、栽插丛数、播栽期、肥料运筹等因素对机插稻产量形成的影响。结果表明,机插稻较直播稻更高产,减穗增粒特征明显。机插稻获得高产的适宜栽插丛数为1.8万丛/667 m2,适宜移栽秧龄为15~20 d,氮肥运筹中基蘖肥与穗肥适宜比例为6∶4,基蘖肥中基肥与分蘖肥适宜比例为3∶7,分蘖肥最适施用时间为移栽后第2叶龄和第3叶龄。提高抽穗至成熟期干物质积累量是提高机插稻产量的重要途径。%Taking the 2012 multi-point data from rice growth monitoring fields in Changzhou city as sample, the effects of planting pattern, planting density, sowing and transplanting date, application of fertilizer on the machine-transplanted rice were analyzed and summarized. The results showed that machine-transplanted rice yield is higher than direct-seeding rice, the main feature is the ears decreasing but the grain number increasing. The optimum planting density of machine-transplanted rice is 1.8×104 points per 667 m2, the optimum transplanted seedling age is 15~20 days, the optimum proportion between the basal-tiller nitrogen and earing nitrogen is 6∶4, the optimum proportion between the basal nitrogen and tiller nitrogen is 3∶7, the optimunm period of the tiller nitrogen is the sec-ond and third leaf age after transplanted. Increasing the accumulation of biological-yield between heading stage and maturity stage is the key way to increase the yield of machine-transplanted rice.

  19. Ecosystem Viable Yields

    CERN Document Server

    De Lara, Michel; Oliveros-Ramos, Ricardo; Tam, Jorge

    2011-01-01

    The World Summit on Sustainable Development (Johannesburg, 2002) encouraged the application of the ecosystem approach by 2010. However, at the same Summit, the signatory States undertook to restore and exploit their stocks at maximum sustainable yield (MSY), a concept and practice without ecosystemic dimension, since MSY is computed species by species, on the basis of a monospecific model. Acknowledging this gap, we propose a definition of "ecosystem viable yields" (EVY) as yields compatible i) with biological viability levels for all time and ii) with an ecosystem dynamics. To the difference of MSY, this notion is not based on equilibrium, but on viability theory, which offers advantages for robustness. For a generic class of multispecies models with harvesting, we provide explicit expressions for the EVY. We apply our approach to the anchovy--hake couple in the Peruvian upwelling ecosystem between the years 1971 and 1981.

  20. Crop yields in intercropping

    NARCIS (Netherlands)

    Yu, Y.

    2016-01-01

    Abstract

    Intercropping, the cultivation of two or more crop species simultaneously in the same field, has been widely practiced by smallholder farmers in developing countries and is gaining increasing interest in developed countries. Intercropping can increase the yield per

  1. Crop yields in intercropping

    NARCIS (Netherlands)

    Yu, Y.

    2016-01-01

    Abstract

    Intercropping, the cultivation of two or more crop species simultaneously in the same field, has been widely practiced by smallholder farmers in developing countries and is gaining increasing interest in developed countries. Intercropping can increase the yield per

  2. Optimizing Model of High-yield and High-efficiency Cultivation Techniques of Relaying Cotton in Garlic%蒜棉套作高产高效栽培技术优化模型

    Institute of Scientific and Technical Information of China (English)

    刘卫星; 苗友顺; 贺群岭; 张枫叶; 刘水仙

    2014-01-01

    To optimize factors affecting relaying cotton in garlic,5 main factors including transplanting date, transplanting density, fertilizing quantity, chemical regulation, and foliar fertilization were studied using quadratic regression orthogonal rotational combining design. A mathematical regression model for lint yield was established. The results showed that the order of the influence from the strongest to the weakest was transplanting density, chemical regulation, fertilizing quantity, foliar fertilization and transplanting date. Transplanting date and foliar fertilization, transplanting density and fertilizing quantity, transplanting density and chemical regulation had significant effects on lint yield. The five agronomic measures should be coordinated effectively. Frequency analysis showed that lint yield of more than 1 900 kg/hm2 could be achieved with the optimal conditions including transplanting from May 5th to 7th with transplanting density between 3.53 and 3.68 (ten thousand plants per hectare), pure nitrogen between 150.84 and 163.80 kg/hm2, burnt potash between 75.42 and 81.90 kg per hectare, chemical regulation between 533.71 and 580.07 mL/hm2 and foliar fertilization between 12.78 and 14.37 kg/hm2.%为了探讨移栽期、移栽密度、追肥量、化控量和叶面喷肥量等5项栽培因子对蒜棉套作模式下棉花皮棉产量的影响,并进一步优化各栽培因子,采用五元二次正交旋转组合设计,建立了蒜棉套作模式下棉花皮棉产量优化数学模型。结果表明,各因素对蒜棉套作模式下棉花皮棉产量的影响由大到小依次为移栽密度、化控量、追肥量、叶面喷肥量和移栽期。移栽期与叶面喷肥量、移栽密度与追肥量、移栽密度与化控量之间的互作效应达到显著水平,生产中应注意协调。频数分析结果表明,蒜棉套作模式下棉花皮棉产量大于1900 kg/hm2的优化栽培措施为5月5~7日移栽,移栽密度3.53万~3.68

  3. Comparative analysis between full-field digital mammography characteristics and pathology of breast phyllode tumor%乳腺分叶状肿瘤全数字化乳腺摄影表现与病理对照分析

    Institute of Scientific and Technical Information of China (English)

    邱云; 丁天一; 刘万花

    2011-01-01

    目的:分析乳腺分叶状肿瘤(PTB)的全数字化乳腺摄影(FFDM)表现,以提高对该病的认识.方法:回顾性分析经手术病理证实的25例PTB的FFDM表现及临床资料,并与病理学分级结果相对照.结果:(1) 25例PTB患者中,病理学分级为良性、交界性、恶性的百分比依次为40%、16%、44%;(2) FFDM主要表现为分叶状肿块,占88%;肿块边缘呈部分光整部分模糊为主,占64%;肿块最长径多大于3 cm,占68%;肿块周围异常血管显示率为68%;肿块伴钙化的发生率为24%,以良性多见,多表现为粗大散在斑状钙化;(3) FFDM诊断与病理诊断符合率为68%.结论:FFDM表现对PTB的诊断具有一定的指导意义.%Objective: To study the full-field digital mammography(FFDM) characteristics of the breast phyllode tumor ( PTB) for enhancing the diagnosis of the disease. Methods: Clinical and FFDM manifestations were retrospectively reviewed in twenty-five women confirmed by surgical pathology. Results; (1) The histologic grades of all cases were respectively benign 40. 0% , borderline 16. 0% and malignant 44. 0%. (2) 88% of cases showed lobulated mass;64% of cases manifested partly well-defined margin and partly obscured margin and 68% of tumors grew larger than 3 cm in diameter;the abnormal blood vessel demonstration of PTB was 68% ; the calcification rate of PTB was 24% , which was more often seen in benign cases, Most calcifications were large and coarse and some of them manifested pleomorphic calcification. ( 3 ) The diagnostic coincidence rate of full-field digital mammography and pathology was 68%. Conclusion; FFDM is helpful for the diagnosis of breast phyllode tumors.

  4. 海南保亭山竹子丰产栽培管理技术%High Yield Cultivation and Management Technique of Mangosteen in Baoting County of Hainan Province

    Institute of Scientific and Technical Information of China (English)

    陈兵; 刘贝贝; 吴磊; 黄小红

    2013-01-01

    Mangosteen is native to Malaysia, it is introduced in Hainan province of China in 1960s. Now Mangosteen has been form scale cultivation in Baoting li and miao autonomous county and surrounding areas of Hainan. According to climate of Baoting county and growth characteristics of mangosteen bearing trees, and in combination with production practice, the high yield cultivation and management of mangosteen, about the crown management, water management, fertilizer management, disease and pest control, fruit harvesting and post-harvest handling, were summarized in this paper, in order to provide technical reference for mangosteen planters.%山竹子原产马来西亚,20世纪60年代开始在海南引种栽培,现已经在海南省保亭县及周边地区形成规模种植。针对保亭地区的气候及山竹子结果树的生长特征,结合生产实际,从树冠管理、水分管理、施肥管理、病虫害防治、果实采收、采后处理等方面,介绍山竹子结果树的丰产栽培及管理技术,为山竹子种植户提供技术参考。

  5. Exploitation and High-yielding Cultivation Technique of Physalis alkekengi in Changbai Mountain%长白山区挂金灯酸浆的开发利用及高产园艺栽培技术

    Institute of Scientific and Technical Information of China (English)

    黄利亚; 金慧; 赵伟; 马宏宇; 代玉红; 赵莹; 金英子; 崔凯峰

    2013-01-01

    Physalis alkekengi has high ornamental value,great medicinal and edible value ,the growth habit of Physalis alkekengi is explored through the systematic study on the introduction and domestication .During its cultivation,seeds should be applied when sexual reproduction .It should have a good harvest this year when asexual reproduction through rooting .It was taboo to be shading in the manufacturing process .But it was apt to like fertilizer and suffer from waterlogging .Bacterial leaf spots and root rot were two main plantain diseases . Topping at the right moment was an important way to obtain high quality and yield .%  挂金灯酸浆的观赏、药用、食用价值较高,通过引种驯化试验探讨其生长习性,研究发现:栽培过程中,有性繁殖时种子需进行处理;无性繁殖时通过分根可当年丰产。生产过程中忌遮阴,喜肥、怕涝。病害主要有叶斑病、根腐病。选择适当时机打顶是挂金灯酸浆优质高产的途径。

  6. 原生质体融合法构建γ-癸内酯高产菌株%Construction of high yield γ-decalactone strains by protoplast fusion technique

    Institute of Scientific and Technical Information of China (English)

    仲惠; 赵玉萍; 李文谦; 李超

    2011-01-01

    该文确定了亲本原生质体制备的最佳条件为:采用0.3%β-巯基乙醇和0.1mol/L EDTA-Na2的复合预处理剂于28℃预处理10min,高渗稳定剂为1 mol/L pH 6.0的山梨醇,蜗牛酶浓度为2%、酶解温度为35℃、时间为2h.经过原生质体融合实验,成功获得了多株高产菌株,其中以QY30 γ-癸内酯产量最高为1.4852g/L,比亲本Y1-2提高了2 82倍.该菌株遗传性状基本稳定.%The optimal conditions for protoplast preparation of parent strain Yarrowia lipolytica were determined as follows: pretreatment with reagent of 0. 3% β-mercaptoethanol and 0. lmol/L EDTA-Na2 at 28℃ for 10min; sorbitol as hyperosmotic stabilizer with lmol/L at pH 6. 0, hydrolysis with 2% snailase at 35℃ for 2h. Several high-yield strains were obtained by protoplast fusion and QY 30 was highest γ-decalactone production strain, which could reach 1. 4852g/L, increased by 2. 82 times compared with parent strain Y1-2. Strain QY 30 was genetic stable.

  7. 食荚豌豆无公害反季节高产栽培技术%Non-Pollution,Off-season and High-yielding Cultivation Techniques of Edible Podded Pea

    Institute of Scientific and Technical Information of China (English)

    陈瑞星

    2011-01-01

    莆田市新县镇利用优越的地理及气候条件发展反季节食荚豌豆生产,取得较高的经济效益。该文总结了新县镇推广反季节食荚豌豆的主要成效,及其无公害栽培技术。%Xinxian town in Putian City developed off-season production of edible podded pea by taking advantage of superior geographic and climatic conditions,which obtained great economy benefit.This paper summarized the main achievements of the extension of off-season edible podded peas and its non-pollution cultivation techniques.

  8. Estimating Corporate Yield Curves

    OpenAIRE

    Antionio Diaz; Frank Skinner

    2001-01-01

    This paper represents the first study of retail deposit spreads of UK financial institutions using stochastic interest rate modelling and the market comparable approach. By replicating quoted fixed deposit rates using the Black Derman and Toy (1990) stochastic interest rate model, we find that the spread between fixed and variable rates of interest can be modeled (and priced) using an interest rate swap analogy. We also find that we can estimate an individual bank deposit yield curve as a spr...

  9. Plant genetics: increasing crop yield.

    Science.gov (United States)

    Day, P R

    1977-09-30

    Cell cultures of crop plants provide new opportunities to recover induced mutations likely to increase crop yield. Approaches include regulating respiration to conserve carbon fixed by photosynthesis, and increasing the nutritive value of seed protein. They depend on devising selecting conditions which only desired mutant cells can survive. Protoplast fusion offers some promise of tapping sources of genetic variation now unavailable because of sterility barriers between species and genera. Difficulties in regenerating cell lines from protoplasts, and plants from cells, still hamper progress but are becoming less severe. Recombinant DNA techniques may allow detection and selection of bacterial cell lines carrying specific DNA sequences. Isolation and amplification of crop plant genes could then lead to ways of transforming plants that will be useful to breeders.

  10. The Research of High-quality and High Yield Culture Technique of Hylocereus Undatus in Huizhou%惠州优质高产火龙果的栽培技术研究

    Institute of Scientific and Technical Information of China (English)

    贺握权; 廖建良; 闻莲; 宋冠华

    2015-01-01

    In order to select excellent pitaya varieties suitable for cultivation in Huizhou region,we analyse biological characteristics and economic characteristics of different pitaya varieties of Huizhou city, and sum up the cultivation techniques of different varieties.The results showed that Xianmiguo No.1, Shihuoquan,Mibao,rouge,and Zhuangzhuang each have their own advantages,but the rouge and Mibao have the highest economic benefit,they are the excellent varieties recommended.%分析惠州市的不同火龙果品种的生物学特性和经济特性,总结不同品种的栽培技术要点,筛选适宜惠州地区栽培的丰产、优质的火龙果品种。结果表明:仙蜜果1号、石火泉、蜜宝、胭脂、壮壮各自都有着自己的优点,但胭脂和蜜宝的经济效益最高,是值得推荐的优良品种。

  11. 全数字化乳腺摄影与MRI对乳腺恶性病变诊断的对比分析%Correlative analysis of full-field digital mammography and MRI findings of breast malignant lesions

    Institute of Scientific and Technical Information of China (English)

    滕妍; 曹满瑞; 刘炳光; 何健龙; 张方璟

    2012-01-01

    目的 探讨乳腺癌全数字化乳腺摄影(full-field digital mammography,FFDM)与乳腺MRI的影像学表现,评价其对乳腺癌的诊断价值.方法 收集68例经穿刺或手术病理证实的乳腺癌病例,对比分析其X线摄影及MRI表现.全数字化乳腺摄影采用常规方法摄片,MRI采用自旋回波T1WI,T2WI序列及动态增强扫描等.结果 68例乳腺恶性肿瘤中,浸润性导管癌57例,浸润性小叶癌3例,叶状囊肉瘤1例,血管肉瘤1例,导管内癌2例,炎性乳癌2例,印戒细胞癌1例,Paget's病1例.乳腺X线摄影诊断正确61例,诊断准确率89.7%.MRI诊断正确66例,诊断准确率97.1%.结论 乳腺X线摄影是乳腺恶性病变的首选检查方法,MRI能更多的显示乳腺病灶的内部特征,二者联合应用对乳腺癌的临床诊断具有重要意义.%Objective To study the imaging and to evaluate the diagnostic value of breast malignant lesions with full-field digital mammography (FFDM) and MRI. Methods We collected 68 cases of breast cancer, which were certified by para-centesis, and pathology, and compared the X-ray and MRI features. Routine photographs were used in FFDM. MRI scanning sequences included T1 WI, T2WI and enhanced MRI etc. Results Of the 68 cases, 57 were infiltrating Duct Carcinoma, 3 were infiltrating lobular carcinoma, 1 was Cystosarcoma Phyllodes, 1 was angiosarcoma, 2 were intraducteal carcinoma, 2 were inflammatory breast cancer, 1 was Signal ring cell carcinoma, and 1 was Paget's disease. 61 cases were found by FFDM, and its invasion hump and malignant calcification were shown, and its accurate proportion was 89. 7%. 66 cases were found by MRI, and its accurate proportion was 97. 1%. Conclusion X-ray mammography was the first choice of imaging examination modalities for breast malignant lesions, and interior feature of malignant breast lesions could be clearly shown by MRI. FFMD in combination with MRI is an important modatity in the diagnosis of breast cancer.

  12. Diagnostic value of full-field digital mammography in mastitis%全数字化乳腺X线摄影对乳腺炎性疾病的诊断价值

    Institute of Scientific and Technical Information of China (English)

    滕妍; 曹满瑞; 赵弘; 何健龙; 邹万娇

    2012-01-01

    Objective:To analyze the full-field digital mammography (FFDM) findings in mastitis and differentiation of mastitis from breast cancer. Methods: 39 cases of mastitis underwent mammography confirmed by surgical pathology were analyzed. Results:Of the 39 cases,26 were chronic mastitis,5 were plasma cell mastitis and 8 were granulomatous mastitis. The mammography showed mass in 17 cases,localized asymmetric density in 20 cases,focal architectural distortion in 2 cases, lymph modes consolidation in 7 cases,localized skin thickening in 12 cases,and indentation of nipple in 7 cases. Conclusion : Mammographic findings in combination with clinical manifestications will be helpful in improving diagnostic accuracy of mastitis.%目的:分析乳腺炎性疾病的全数字化乳腺X线摄影(FFDM)表现,提高该病与乳腺癌的鉴别诊断水平.方法:回顾性分析39例经穿刺或手术病理证实的乳腺炎性疾病的FFDM表现.结果:39例患者中,26例为慢性乳腺炎,5例为浆细胞性乳腺炎,8例为肉芽肿性乳腺炎.X线表现为肿块影17例,局部腺体非对称性致密影20例,结构扭曲2例.伴同侧腋下淋巴结致密影7例,局部或乳晕区皮肤增厚12例,乳头凹陷7例.结论:结合临床资料并细致分析乳腺炎性疾病的FFDM表现,有助于提高该病诊断与鉴别诊断水平.

  13. Application of full-field optical coherence tomography for cell imaging%全场光学相干层析在细胞成像中的应用研究

    Institute of Scientific and Technical Information of China (English)

    胡斌; 江兴方; 石晓灏; 刘磊; 邓林红

    2016-01-01

    研制了一套基于Linnik干涉仪的全场光学相干层析(FF-OCT)系统对细胞进行层析成像.不同于其他FF-OCT系统的成像方法,该系统采用了基于Hilbert变换的图像恢复算法,只需2幅移相干涉图就可以恢复样品的结构信息,即使移相出现误差,仍能得到样品层析图.系统的实测纵向、横向分辨率分别达到1.1 μm、2.5 μm.通过对洋葱表皮细胞的初步成像实验,验证了该FF-OCT系统的可行性,为进一步实现高分辨率细胞成像奠定了基础.%A Linnik type full-field optical coherence tomography (FF-OCT) system is developed for tomographic imaging of biological cells.Different from other imaging methods used in FF-OCT systems,an image restoration method based on Hilbert transform is adopted,which requires only two interference images to recover the structure information of the sample.Even if the phase shift error occurs,the sample chromatogram can still be obtained.The measured longitudinal and lateral resolutions of the system reach 1.1 μm and 2.5 μm,respectively.Feasibility of the FF-OCT system is verified by preliminary imaging experiments of onion epidermal cells,and it lays foundation for the further realization of high resolution cell imaging.

  14. 浙西南山区旱地多熟套种马铃薯高产高效技术%High-yield and High-benefit Techniques for Polyripe Intercropping Potato for Dry Farmland of Mountain Area in the Southwest of Zhejiang Province

    Institute of Scientific and Technical Information of China (English)

    吕伟德; 吕周林

    2001-01-01

    马铃薯是浙西南山区旱地多熟间套种的主要冬季作物,经过几年的试验研究和生产实践,形成了适用于山区旱地马铃薯留种途径、良种选择、切块播种、覆盖、种植群体以及施肥等高产高效栽培技术体系。%Potato is a main winter crop for ployripe intercropping of dry farmland of mountain area in the southwest of Zhejiang province. The high-yield and high-benefit cultivation techniques had been groped by experiments and practices for some years. These techniques include seed tuber keeping,variety selection, tuber cutting,covering,plant density and fertilizing.

  15. Study on Grown Performance and High Yield Cultural Techniques of Conventional Rice Guinongzhan in Wenchang City%优质常规稻桂农占在文昌市的试种表现及高产栽培技术研究

    Institute of Scientific and Technical Information of China (English)

    郑丹艳

    2011-01-01

    Guinongzhan was the super rice breeding variety bred by rice research institute of Guangdong academy of agricultural sciences. It has characteristics of wide adaptability, high yield, great resistance and high quality, and is suitable to plant in Wenchang city as early and late rice. Agronomic traits, grain quality, resistance and yield performance were introduced and high yield cultural techniques of Guinongzhan were summarized including the time of sowing, breeding the vigorous seedlings, reasonable density, scientific fertilization, reasonable irrigation and pest control.%桂农占是广东省农业科学院水稻研究所选育的广适型优质超级稻品种。该品种具有适应性广、丰产性好、抗性强、米质优等特点,是一个适宜在海南省文昌市早、晚造种植的常规稻种。介绍了桂农占在文昌市的农艺性状、米质、抗性和产量表现,并总结了该品种的高产栽培技术,包括适时播种、培育壮秧、合理密植、科学施肥、合理排灌、及时防治病虫害等。

  16. WE-G-BRD-01: A Data-Driven 4D-MRI Motion Model to Estimate Full Field-Of-View Abdominal Motion From 2D Image Navigators During MR-Linac Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Stemkens, B; Tijssen, RHN; Denis de Senneville, B Denis; Lagendijk, JJW; Berg, CAT van den [University Medical Center Utrecht, Utrecht (Netherlands)

    2015-06-15

    Purpose: To estimate full field-of-view abdominal respiratory motion from fast 2D image navigators using a 4D-MRI based motion model. This will allow for radiation dose accumulation mapping during MR-Linac treatment. Methods: Experiments were conducted on a Philips Ingenia 1.5T MRI. First, a retrospectively ordered 4D-MRI was constructed using 3D transient-bSSFP with radial in-plane sampling. Motion fields were calculated through 3D non-rigid registration. From these motion fields a PCA-based abdominal motion model was constructed and used to warp a 3D reference volume to fast 2D cine-MR image navigators that can be used for real-time tracking. To test this procedure, a time-series consisting of two interleaved orthogonal slices (sagittal and coronal), positioned on the pancreas or kidneys, were acquired for 1m38s (dynamic scan-time=0.196ms), during normal, shallow, or deep breathing. The coronal slices were used to update the optimal weights for the first two PCA components, in order to warp the 3D reference image and construct a dynamic 4D-MRI time-series. The interleaved sagittal slices served as an independent measure to test the model’s accuracy and fit. Spatial maps of the root-mean-squared error (RMSE) and histograms of the motion differences within the pancreas and kidneys were used to evaluate the method. Results: Cranio-caudal motion was accurately calculated within the pancreas using the model for normal and shallow breathing with an RMSE of 1.6mm and 1.5mm and a histogram median and standard deviation below 0.2 and 1.7mm, respectively. For deep-breathing an underestimation of the inhale amplitude was observed (RMSE=4.1mm). Respiratory-induced antero-posterior and lateral motion were correctly mapped (RMSE=0.6/0.5mm). Kidney motion demonstrated good motion estimation with RMSE-values of 0.95 and 2.4mm for the right and left kidney, respectively. Conclusion: We have demonstrated a method that can calculate dynamic 3D abdominal motion in a large volume

  17. 全数字化乳腺摄影常见伪影与对策探讨%Artifacts Found in Full-field Digital Mammography and Corresponding Disposal

    Institute of Scientific and Technical Information of China (English)

    康静霞

    2011-01-01

    Objective: To study artifacts found in full-field digital mammography (FFDM) and apply the effective means to avoid them in order to improve image quality and provide favourable information for clinical diagnosis.Methods: The categories and causes of mammry artifacts found in 3000 patients( 12000 pictures) obtained from 2007.06 to 2009.06 by using GE senographe DS, Kodak dry laser printer and Kodak dry view were analyzed retrospectively.Results: Artifical artifacts 100 images(0.8%); Printer artifacts 30 images (0.25%); Imaging plate artifacts 12 images (0.1%); Grid artifacts 10 images (0.008%)and any other artifacts 6 images (0.005%).Conclusions: The artifacts can be efficiently restrained or eliminatd ifthe factors that induce artifacts are correctly recognized and the effective means are applied.%目的:探讨全数字化乳腺摄影(FFDM)中常见伪影的形成与消除方法,以减少或消除乳腺检查时产生的伪影,达到改善图像的质量,为诊断提供良好的影像资料.方法:回顾性分析2007年6月至2009年6月使用GE senographe DS钼铑双靶数字成像设备、柯达8900干式激光打印机、柯达干式激光片行3000例次(图像12000幅)乳腺摄影,产生伪影的种类及其原因.结果:人为伪影100幅(0.8%);打印机伪影30幅(0.25%);成像板伪影12幅(0.1%);滤线栅伪影10幅(0.08%);其他伪影6幅(0.05%).结论:正确认识各种常见伪影及其产生的原因,才能充分地利用各种技术,来有效地抑制或消除伪影,提高图像质量.

  18. Correlation Analysis of some Growth, Yield, Yield Components and ...

    African Journals Online (AJOL)

    Keywords: Correlation, Wheat; growth, yield, yield components, grain quality. INTRODUCTION. Wheat ... macaroni, biscuits, cookies, cakes, pasta, noodles and couscous; beer, many .... and 6 WAS which ensured weed free plots. Fertilizer was ...

  19. Maximizing ROI with yield management

    National Research Council Canada - National Science Library

    Neil Snyder

    2001-01-01

    .... the technology is based on the concept of yield management, which aims to sell the right product to the right customer at the right price and the right time therefore maximizing revenue, or yield...

  20. Shortcomings in wheat yield predictions

    Science.gov (United States)

    Semenov, Mikhail A.; Mitchell, Rowan A. C.; Whitmore, Andrew P.; Hawkesford, Malcolm J.; Parry, Martin A. J.; Shewry, Peter R.

    2012-06-01

    Predictions of a 40-140% increase in wheat yield by 2050, reported in the UK Climate Change Risk Assessment, are based on a simplistic approach that ignores key factors affecting yields and hence are seriously misleading.

  1. Correlative Analysis of Full-field Digital Mammography and MRI Findings of Breast non-lactation Mastitis%非哺乳期乳腺炎X线摄影及磁共振表现照研究

    Institute of Scientific and Technical Information of China (English)

    滕妍; 郭吉敏; 曹满瑞; 张方璟; 刘炳光; 何健龙

    2012-01-01

    目的 探讨非哺乳期乳腺炎全数字化孔腺X线摄影(full-fielddigital mammography,FFDM)及MRI的影像学表现,评价其对非哺乳期乳腺炎性疾病的诊断价值.方法 收集26例非哺乳期乳腺炎性疾病患者,均经穿刺或手术病理证实,回顾性分析其乳腺X线摄影及MRI影像学表现,并进行对照分析.同时收集3例炎性乳癌病例,分析其X线摄影及MRI表现.结果 26例患者中,慢性乳腺炎17例,肉芽肿性乳腺炎7例,浆细胞性乳腺炎2例.乳腺X线摄影表现为局部腺体致密16例,肿块8例,结构扭曲1例,无直接征象,仅表现为局部皮肤增厚1例;MRI平扫病灶T1WI呈低、等信号,T2WI呈等、高或混杂信号,增强扫描呈非肿块样强化18例,肿块样强化8例.3例炎性乳癌X线及MRI表现与急性乳腺炎相似,其中1例X线摄影出现恶性钙化,可以确诊.结论 非哺乳期乳腺炎与乳腺癌临床及影像学检查有时较难鉴别,乳腺X线摄影与MRI联合应用能提供更多影像学信息,提高该病诊断准确率.%Objective To study the imaging and evaluate the diagnosis value of breast non-lactation mastitis with full-field digital mammography(FFDM)and MRI. Methods Collected 26 cases of mastitis and another 3 cases of inflammatory breast cancer which were certified by pathology.and retrospective analyzed the X-ray and MRI features. Results Of the 26 cases, 17 were chronicity mastitis, 7 were granulomatous mastitis, and 2 were plasma cell mastitis. The findings were shown in FFDM: 16 were localized asymmetric density, 8 were mass, 2 were focal architectural distortion, and 1 was thickening of skin, without direct sign. The MR sings of mastitis lesions included low or isointensity signal on T1WI images, isointensityiφhyperintensity or promiscuity signal on T2WI images. The mastitis lesions appeared patchy enhancement were 18 cases, and mass sample enhancement were 8 cases. The 3 cases of inflammatory breast cancer were similar with acute

  2. Principal component regression for crop yield estimation

    CERN Document Server

    Suryanarayana, T M V

    2016-01-01

    This book highlights the estimation of crop yield in Central Gujarat, especially with regard to the development of Multiple Regression Models and Principal Component Regression (PCR) models using climatological parameters as independent variables and crop yield as a dependent variable. It subsequently compares the multiple linear regression (MLR) and PCR results, and discusses the significance of PCR for crop yield estimation. In this context, the book also covers Principal Component Analysis (PCA), a statistical procedure used to reduce a number of correlated variables into a smaller number of uncorrelated variables called principal components (PC). This book will be helpful to the students and researchers, starting their works on climate and agriculture, mainly focussing on estimation models. The flow of chapters takes the readers in a smooth path, in understanding climate and weather and impact of climate change, and gradually proceeds towards downscaling techniques and then finally towards development of ...

  3. Fission yield studies at the IGISOL facility

    Energy Technology Data Exchange (ETDEWEB)

    Penttilae, H.; Elomaa, V.V.; Eronen, T.; Hakala, J.; Jokinen, A.; Kankainen, A.; Moore, I.D.; Rahaman, S.; Rinta-Antila, S.; Rissanen, J.; Saastamoinen, A.; Weber, C.; Aeystoe, J. [University of Jyvaeskylae, Department of Physics, Jyvaeskylae (Finland); Rubchenya, V. [University of Jyvaeskylae, Department of Physics, Jyvaeskylae (Finland); V.G. Khlopin Radium Institute, St. Petersburg (Russian Federation)

    2012-04-15

    Low-energy-particle-induced fission is a cost-effective way to produce neutron-rich nuclei for spectroscopic studies. Fission has been utilized at the IGISOL to produce isotopes for decay and nuclear structure studies, collinear laser spectroscopy and precision mass measurements. The ion guide technique is also very suitable for the fission yield measurements, which can be performed very efficiently by using the Penning trap for fission fragment identification and counting. The proton- and neutron-induced fission yield measurements at the IGISOL are reviewed, and the independent isotopic yields of Zn, Ga, Rb, Sr, Cd and In in 25MeV deuterium-induced fission are presented for the first time. Moving to a new location next to the high intensity MCC30/15 light-ion cyclotron will allow also the use of the neutron-induced fission to produce the neutron rich nuclei at the IGISOL in the future. (orig.)

  4. Soybean growth and yield under cover crops

    Directory of Open Access Journals (Sweden)

    Priscila de Oliveira

    2013-04-01

    Full Text Available The use of cover crops in no-tillage systems can provide better conditions for the development of soybean plants with positive effects on grain yield and growth analysis techniques allow researchers to characterize and understand the behavior of soybean plants under different straw covers. Thus, the aim of this study was to characterize, using growth analysis, yield components and agronomic performance of soybean under common bean, Brachiaria brizantha and pearl millet straws. The experiment was performed on a soil under cerrado in the municipality of Santo Antônio de Goiás, GO. The experiment was arranged in a randomized complete block design with three treatments (cover crops and five replications. Soybean grain yield was lower in the B. brizantha straw treatment (3,708 kg ha-1 than both in the pearl millet (4.772 kg ha-1 and common bean straw treatments (5,200 kg ha-1. The soybean growth analysis in B. brizantha, pearl millet and common bean allowed characterizing the variation in the production of dry matter of leaves, stems, pods and total and leaf area index that provided different grain yields. The cover crop directly affects the soybean grain yield.

  5. High yield DNA fragmentation using cyclical hydrodynamic shearing

    NARCIS (Netherlands)

    Shui, Lingling; Sparreboom, Wouter; Spang, Peter; Roeser, Tina; Nieto, Benjamin; Guasch, Francesc; Corbera, Antoni Homs; van den Berg, Albert; Carlen, Edwin

    2013-01-01

    We report a new DNA fragmentation technique that significantly simplifies conventional hydrodynamic shearing fragmentation by eliminating the need for sample recirculation while maintaining high fragmentation yield and low fragment length variation, and therefore, reduces instrument complexity and c

  6. High yield DNA fragmentation using cyclical hydrodynamic shearing

    NARCIS (Netherlands)

    Shui, Lingling; Sparreboom, Wouter; Spang, Peter; Roeser, Tina; Nieto, Benjamin; Guasch, Francesc; Corbera, Antoni Homs; van den Berg, Albert; Carlen, Edwin

    2013-01-01

    We report a new DNA fragmentation technique that significantly simplifies conventional hydrodynamic shearing fragmentation by eliminating the need for sample recirculation while maintaining high fragmentation yield and low fragment length variation, and therefore, reduces instrument complexity and

  7. 全数字化乳腺摄影不典型乳腺肿块的X线征象分析%The X-ray features analysis of the atypical breast lumps in full field digital mammography

    Institute of Scientific and Technical Information of China (English)

    孙艳莉

    2015-01-01

    目的:分析36例不典型乳腺肿块的影像学表现,提高影像学诊断水平。方法随机抽取2010年8月~2014年8月,经手术病理证实的乳腺不典型肿块36例,回顾性分析其数字乳腺摄影的影像学表现。结果36例43个肿块,术前诊断BI‐RADSⅡ类5例,BI‐RADSⅢ类17例,BI‐RADSⅣ类14例。其中12例纤维腺瘤(5例多发)因腺体较丰富,肿块与腺体重叠,边缘显示不清,表现为等密度肿块;5例脂肪瘤及2例错构瘤主要位于皮下脂肪层及退化不全的乳腺内,肿块与腺体组织分解不清,表现为与周围组织等密度肿块;4例硬化性腺病及2例慢性炎性病变,表现为稍高密度不均匀肿块;11例乳腺癌分别表现为星状影(2例)、结构扭曲(5例)和非对称密度影(4例),其中3例非对称密度影伴钙化。结论不典型乳腺肿块数字乳腺摄影诊断常较困难,密切结合临床触诊,充分运用特殊体位摄影及图像后处理功能,对可疑病变及时进行穿刺活检或外科手术切除活检,可大幅提高不典型乳腺肿块,尤其是不典型乳腺癌的检出率和诊断符合率。%Objective To analyze the imaging findings of 36 cases of atypical breast lumpsinorder to further improve the level of imaging diagnosis of the atypical breast lumps ,especially the breast cancer .Methods Extract randomly 36 cases of atypical breast lumps confirmed by surgery pathology with complete information from August in 2010 to August in 2014 ,and analyze retrospectively their imaging findings with full field digital mammography .Results 43 lumps in 36 ca‐ses were found and diagnosed before operation ,including BI‐RADSⅡ 5 cases ,BI‐RADS Ⅲ 17 cases ,BI‐RADS Ⅳ 14 ca‐ses .12 cases of fibro adenoma (5 cases were frequentil multiple) hand no clear edge because their gland was rich and the bump and gland were lapped ,showed isopycnic lump ,5 cases lipoma and 2 cases

  8. 全数字化乳腺X线摄影在乳腺癌诊断中的作用%Diagnostic Role of Full Field Mammography for Breast Carcinoma

    Institute of Scientific and Technical Information of China (English)

    刘伟; 沈钧康; 周丽娟

    2012-01-01

    Objective To analyzes the mammographic features of breast lesions confirmed by pathology, in order to improve the diagnostic accuracy of full field mammography (FFDM) in detecting breast carcinoma. Methods The mammographic features of 313 patients with breast lesions between January 2008 to October 2010 confirmed by operation and pathology were analyzed. The radiologists in breast imaging assessment analyzed and classified all the mammograms according to breast imaging reporting and data system (BI-RADS). The sensitivity, specificity, accuracy, positive predictive value (PPV) and negative predictive value (NPV) were evaluated according to their pathological diagnosis. The reasons resulting in false-positive and false-negative diagnosis were analyzed. Results Of all the 313 breast lesions, 194 were malignant, and 119 were benign. Of the malignant lesions, mass simplex type was found in 83; and masses with calcification type were found in 72. Among all the patients, there were 18 false-positive cases and 20 false- negative. The sensitivity, specificity, accuracy, PPV and NPV of FFDM in detecting breast carcinoma were 89.2%, 84.9%, 87.7%, 90.6%, and 82.8%, respectively. The false-positive signs were masses and tiny calcification which were common to malignant lesions. The false-negative signs were dense mammary gland, dissymmetrical density and tiny architectural distortion. Conclusions FFDM has its higher value in the diagnosis of breast carcinoma. Breast carcinoma with different types has its characteristic X-ray results%目的 分析经手术病理证实的乳腺病变在全数字化乳腺摄影(FFDM)中的影像学表现,提高X线在乳腺癌诊断中的准确性.方法 搜集2008年1月-2010年10月313例行FFDM检查、手术和病理证实的乳腺病变患者的临床资料及乳腺X线片,由放射科医师对患者的X线片观察并分析,参照乳腺影像学报告和数据系统(BIRADS)进行分级,以术后病理结果为金标准,评价FFDM检查诊

  9. 1型糖尿病患儿全视野闪光视网膜电图反应特征%Features of full field electroretinogram responses in children with early type 1 diabetes

    Institute of Scientific and Technical Information of China (English)

    白雪晴; 余继锋; 施维; 崔燕辉; 刘雯; 田利荣; 李莉

    2016-01-01

    目的 观察1型糖尿病(T1D)患儿全视野闪光视网膜电图(FF-ERG)反应特征.方法 回顾性临床病例研究.T1D患儿41例(T1D组)及轻度屈光不正儿童25名(对照组)纳入研究.所有T1D患儿视力、屈光度、眼压、裂隙灯显微镜、眼底彩色照相、间接检眼镜及光相干断层扫描检查排除糖尿病视网膜病变.所有受检儿均由同一位有经验的技师进行FF-ERG检查.包括暗适应视杆细胞反应0.01(r-b 0.01)、暗适应最大混合反应3.0(mix-a 3.0、mix-b 3.0)、暗适应最大混合反应10.0 (mix-a 10.0、mix-b 10.0)、暗适应3.0振荡电位2(OP2)、明适应视锥细胞反应3.0(c-a 3.0、c-b 3.0)及30 Hz闪烁光反应(30 HzFP)的振幅、潜伏期.对比分析两组受检儿FF-ERG各反应振幅及潜伏期差异.结果 与对照组比较,T1D组患儿各反应振幅降低,潜伏期延长.两组受检儿各反应振幅比较,除r-b 0.01振幅(t=-0.228,P>0.05)之外,其余各反应振幅之间的差异均有统计学意义(t=-1.664、-3.645、-4.324、-6.123、-5.846、-12.900、-14.400、-5.230,P<0.05).两组受检儿各反应潜伏期比较,mix-b 3.0、mix-b 10.0、c-b 3.0及OP2潜伏期之间的差异有统计学意义(t=5.242、2.879、5.378、3.506,P<0.05);r-b 0.01、mix-a 3.0、mix-a 10.0、c-a 3.0、30 Hz FP潜伏期之间的差异无统计学意义(t=2.331、1.677、0.557、0.840、0.064,P>0.05).结论 TID组患儿较正常儿童FF-ERG反应振幅降低,潜伏期延长.%Objective To observe the features of the full field electroretinogram (FF-ERG) in type 1 diabetes (T1D) children without diabetic retinopathy (DR).Methods Retrospective case study.Forty-one T1D children and 25 age-matched normal controls underwent a complete ophthalmic examination,including best-corrected visual acuity,refraction,intraocular pressure,slit lamp,fundus photography,indirect ophthalmoscopy,and spectral domain optical coherence tomography to exclude DR.All FF-ERG tests were performed by an

  10. Yield model for unthinned Sitka spruce plantations in Ireland

    Energy Technology Data Exchange (ETDEWEB)

    Omiyale, O.; Joyce, P.M.

    1982-01-01

    Over the past few decades the construction of yield models, has progressed from the graphical through mathematical and biomathematic approach. The development of a biomathematical growth model for Sitka spruce plantations is described. It is suggested that this technique can serve as a basis for general yield model construction of plantation species in Ireland. (Refs. 15).

  11. Genetic relationship between yield and yield components of maize

    Directory of Open Access Journals (Sweden)

    Nastasić Aleksandra

    2010-01-01

    Full Text Available One of the objectives of this paper was to determine relationship between grain yield and yield components, in S1 and HS progenies of one early synthetic maize population. Grain yield was in high significant, medium strong and strong association with all studied yield components, in both populations. The strongest correlation was recorded between grain yield and 1000-kernel weight (S1 progenies rg = 0.684; HS progenies rg = 0.633. Between other studied traits, the highest values of genotypic coefficient of correlations were found between 1000-kernel weight and kernel depth in S1 population, and 1000-kernel weight and ear length in HS population. Also, objective of this research was founding the direct and indirect effects of yield components on grain yield. Desirable, high significant influence on grain yield, in path coefficient analysis, was found for 1000-kernel weight and kernel row number, and in S1 and HS progenies, and for ear length in population of S1 progenies. Kernel depth has undesirable direct effect on grain yield, in both populations.

  12. Breeding and Cultivation Technique of High-yield and High-quality Hybrid Maize Yundan 20 with Multiple Resistances%高产・多抗・优质玉米杂交种郧单20的选育及栽培技术

    Institute of Scientific and Technical Information of China (English)

    周刚; 李永学; 吴承国; 唐余成; 陈光勇; 王致云; 柯磊

    2016-01-01

    Yundan 20 is a high-yield and high-quality hybrid maize variety with multiple resistances , which is bred by Shiyan Academy of Agri-culture Sciences.Its female parent is WD01 bred by Shiyan Academy of Agriculture Sciences and male parent is T259 which is introduced.In 2016, Yundan 20 was approved by the Crop Variety Approval Committee of Hubei Province, with a variety approval number 2016005.The breed-ing process, integral characteristics, cultivation techniques and seed production techniques of Yundan 20 were summarized and analyzed , which aimed to promote the variety and meet market demand .%郧单20是湖北省十堰市农业科学院采用自选系WD01作母本、外引系T259作父本选育的高产、多抗、品种优良的玉米新品种,2016年通过湖北省农作物品种审定委员会审定,品种审定编号为2016005。通过对郧单20选育过程、综合特性、栽培技术、制种技术等方面进行总结和分析,以期推广该品种,满足市场需求。

  13. Effect of density and planting pattern on yield and yield

    Directory of Open Access Journals (Sweden)

    alireza yadavi

    2009-06-01

    Full Text Available In order to evaluate competition ability of Grain maize (Zea mays L. against redroot pigweed (Amaranthus retroflexus L. a field experiment was conducted at Esfahan on 2003. In this research the effect of corn spatial arrangement on yield and yield components of corn (647 Three Way Cross hybrids under different levels of redroot pigweed infestation was investigated. Treatments were arranged in a factorial split experiment based on RCBD with three replications. Factorial arrangement of corn densities (74000 and 111000 plant ha-1 and planting patterns (single row, rectangular twin row and zigzag twin row formed the main plots. Split-plots referred to pigweed densities (0, 4, 8 and 12 plant m-1. Results showed that both grain and biological yield of corn increased as corn density rates increased but rows number per cob, number of grains per row of cob and 1000 grains weight decreased. The effects of planting arrangement on yield and yield components despite rows grain in cob, 1000 seeds weight and harvest index were statistically significant. Corn grain yield and yield components decreased significantly by increasing pigweed density. The effect of redroot pigweed density on corn grain and biological yield loss was predicted using Cousence hyperbolic yield equation. It showed that maximum grain yield loss and biological yield loss happened in single row arrangement and low corn density. Rows number per cob and grain numbers per row in higher corn density treatment showed lower reduction slopes under pigweed competition. In addition, grain rows numbers per cob and corn harvest index in twin arrangement treatments decreased lower than single row treatment under pigweed competition. The results of this research indicated that corn competition ability against redroot pigweed could be increased using dense population (1/5 fold of general density and zigzag twin row arrangement.

  14. Systematics in delayed neutron yields

    Energy Technology Data Exchange (ETDEWEB)

    Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan). Atomic Energy Research Inst.

    1998-03-01

    An attempt was made to reproduce the systematic trend observed in the delayed neutron yields for actinides on the basis of the five-Gaussian representation of the fission yield together with available data sets for delayed neutron emission probability. It was found that systematic decrease in DNY for heavier actinides is mainly due to decrease of fission yields of precursors in the lighter side of the light fragment region. (author)

  15. Interdependence of yield and yield components of confectionary sunflower hybrids

    Directory of Open Access Journals (Sweden)

    Hladni Nada

    2011-01-01

    Full Text Available The two most important criteria for introducing new confectionary hybrids into production are high seed and protein yield. That is why it is important to find the traits that are measurable, and that at the same time show a strong correlation with seed and protein yield, so that they can be used as a criteria for confectionary hybrid breeding. Results achieved during 2008 at the locations Rimski Šančevi (Region of Vojvodina and Kula (Central Serbia show that the new confectionary hybrids are expressing higher seed yields in comparison to standards (Vranac and Cepko though with a lower seed oil content. A very strong positive correlation was determined between seed yield and seed protein content, kernel content and mass of 1000 seeds. A very strong positive correlation was determined between seed protein content, seed yield and mass of 1000 seeds, with protein yield. This indicates that seed yield, seed protein content and mass of 1000 seeds have a high influence on protein yield. The degree of interdependence between different traits is a sign of direction which is supposed to facilitate better planning of sunflower breeding program.

  16. Effects of Yield-increasing on Techniques of Whole Plastic-film Mulching on Double Ridges and Planting in Catchment Furrows of Dry-land Maize%旱地玉米全膜双垄沟播技术增产效果研究

    Institute of Scientific and Technical Information of China (English)

    刘广才; 杨祁峰; 李来祥; 段禳全; 朱永永

    2009-01-01

    采用田间小区试验研究了不同旱作区玉米全膜双垄沟播技术的增产效果.结果表明,不同覆膜方式增产幅度以全膜双垄沟播技术极其显著地高于半膜双垄沟播技术、半膜双垄沟播明显高于半膜平铺穴播,不同覆膜时间增产幅度以秋季覆膜处理最高、顶凌覆膜次之、播前覆膜最低;全膜双垄沟播玉米增产幅度明显表现为:半干旱偏旱区>半干旱区>半湿润偏旱区.三个旱作区秋季全膜双垄春季沟播玉米较对照播前半膜平铺穴播(下同)增产率分别为48.1%、39.6%和34.3%,顶凌全膜双垄春季沟播玉米较对照增产率分别为40.6%、35.0%和31.7%,播前全膜双垄沟播玉米较对照增产率分别为35.0%、30.3%和28.0%;全膜双垄沟播玉米增产量则表现为:半湿润偏早区明显高于半干旱区,半干旱区又明显高于半干旱偏旱区,特别是年降雨600mm的旱作区秋季、顶凌全膜双垄春季沟播玉米产量分别达到12375.0kg/hm~2、12192.0kg/hm~2,达到了旱作玉米超高产.%Field plot experiments were employed to investigate yield-increasing effects for the techniques of whole plastic-film mulching on double ridges and planting in catchment furrows of maize under different film mulching modes in different arid areas. The results showed that seeing from different film mulching modes, yield-increasing extent of whole mulching on double ridges was significantly higher than that of half mulching on double ridges, and half mulching on double ridges was remarkably higher than half fiat mulching; seeing from different film mulching times, yield-increasing extent of autumn mulching was much higher than that of early spring mulching, and early spring mulching was much higher than sowing mulching. The yield-increasing degrees of whole mulching on double ridges in semi-arid to the arid side areas were evidently higher than those in semi-arid area, and semi-arid areas were evidently higher than semi-humid to

  17. Research Advances in the Physiological and Biochemical Mechanism in Water-saving Irrigation Techniques for High Yield and High Efficiency of Transplanted Rice%移栽水稻高产高效节水灌溉技术的生理生化机理研究进展

    Institute of Scientific and Technical Information of China (English)

    陈婷婷; 杨建昌

    2014-01-01

    The water crisis is threatening rice sustainability and food security in the world.Agricultural scientists have developed a variety of water-saving irrigation techniques and production systems in order to deal with water shortages meanwhile to increase food production.This paper reviewed dominant water-saving irrigation techniques applied in transplanted rice production,summarized their physiological and biochemical mechanism for rice growth,hormones, and activities of key enzymes involved in sucrose-to-starch conversion.The problems existed in water-saving irrigation techniques for high-yielding and high-efficiency of rice and research prospects were put forward and discussed.%水资源匮乏威胁水稻生产的可持续发展和粮食安全。为了应对水资源紧缺和增加粮食产量,农业科学家开发了各种节水灌溉技术和生产体系。本文综述了当前移栽水稻生产上主要应用的节水灌溉技术并从水稻生长、激素、蔗糖-淀粉代谢途径关键酶活性等方面阐述了其生理生化机制,提出水稻高产高效节水灌溉技术存在的问题与研究展望。

  18. Effects of rates of nitrogen on yield and yield components of winter triticale

    Directory of Open Access Journals (Sweden)

    Lalević Dragana N.

    2016-01-01

    Full Text Available Due to the high genetic potential for yield and favourable nutritional value, triticale is a promising plant species. For achieving high and stable yields, it is necessary to have favorable agroclimatic conditions of the locality, variety and advanced agricultural techniques, with special emphasis on fertilizing. This study examines the effect of increasing rates of nitrogen on yield and yield components of five cultivars of winter triticale: Odisej, Kg-20, Triumph, Rtanj and Tango. The three-year trial (2009-2012, which was set up in a randomized block system with three replications, included control and three different doses of nitrogen fertilization (0, 60, 90 and 120 kg ha-1. In all variants of fertilization, 80 kg ha-1 P2O5 and K2O were added beside nitrogen. The obtained results showed that the use of nitrogen had a positive effect on yield and yield components in all variants and in all cultivars. The variety Tango had the highest average grain yield, while the variety Kg-20 had the lowest. Also, Tango had the highest value of the 1000 grain mass and the number of grains per spike, while Triumph had the highest value of hectoliter weight. The application of fertilizers led to a very large and significant increase of yield compared with the control. Accordingly, all studied cultivars had the highest yield with the highest quantities of nitrogen (120 kg ha-1. Considering that triticale is intended mainly for feeding livestock, the results of these studies would be valuable in terms of its growing as a forage crop as well as in terms of its breeding for grain quality and productivity.

  19. Analysis of the Effect of High Yield of Feizixiao Litchi after Implements Spiral Girdling techniques Under the Bad Weather Condition%不良天气条件下妃子笑荔枝螺旋环剥增产效果分析

    Institute of Scientific and Technical Information of China (English)

    夏小曼; 黄汝红; 杨兰英; 谢仁忠

    2011-01-01

    When the Litchi Chinese Sonn.cv. Feizixiao is going to enter the flower bud differentiation period , implements the spiral girdling, observes its growth periods and the yields and its components. The results showed that the effec of high yield is obvious after implements spiral girdling techniques under the bad aweather conditions, the reasons are as follow: ( 1 ) when the fall and the winter temperature is exceptionally, the spiral girdleing can inhibit the growing of the winter shoots and promote the flower bud differentiation, beneficial to the blossom and the bear fruit; (2) the spiral girdleing can postpone the flowering season, evading the adverse effec for the low temperature and continuous rainning; (3) when the Spring temperature is exceptionally high, the spiral girdling can inhibit blossom clusters form leaf lets and promote the flower formation.%在妃子笑荔枝将要进入花芽分化期时实施螺旋环剥,观测其各生育期及产量构成要素。结果表明螺旋环剥在不良天气条件下的增产效果明显.其原因是:在秋、冬季气温偏高的天气条件下,螺旋环剥能抑制冬梢抽发,促进花芽分化,有利开花结果;螺旋环剥能推迟花期,有利于避过花期低温连阴雨天气的不良影响;春季气温偏高的天气条件下,螺旋环剥能抑制“冲梢”,利于花穗发育。

  20. Specific yield: compilation of specific yields for various materials

    Science.gov (United States)

    Johnson, A.I.

    1967-01-01

    Specific yield is defined as the ratio of (1) the volume of water that a saturated rock or soil will yield by gravity to (2) the total volume of the rock or soft. Specific yield is usually expressed as a percentage. The value is not definitive, because the quantity of water that will drain by gravity depends on variables such as duration of drainage, temperature, mineral composition of the water, and various physical characteristics of the rock or soil under consideration. Values of specific yields nevertheless offer a convenient means by which hydrologists can estimate the water-yielding capacities of earth materials and, as such, are very useful in hydrologic studies. The present report consists mostly of direct or modified quotations from many selected reports that present and evaluate methods for determining specific yield, limitations of those methods, and results of the determinations made on a wide variety of rock and soil materials. Although no particular values are recommended in this report, a table summarizes values of specific yield, and their averages, determined for 10 rock textures. The following is an abstract of the table. [Table

  1. Incorporating phenology into yield models

    Science.gov (United States)

    Gray, J. M.; Friedl, M. A.

    2015-12-01

    Because the yields of many crops are sensitive to meteorological forcing during specific growth stages, phenological information has potential utility in yield mapping and forecasting exercises. However, most attempts to explain the spatiotemporal variability in crop yields with weather data have relied on growth stage definitions that do not change from year-to-year, even though planting, maturity, and harvesting dates show significant interannual variability. We tested the hypothesis that quantifying temperature exposures over dynamically determined growth stages would better explain observed spatiotemporal variability in crop yields than statically defined time periods. Specifically, we used National Agricultural and Statistics Service (NASS) crop progress data to identify the timing of the start of the maize reproductive growth stage ("silking"), and examined the correlation between county-scale yield anomalies and temperature exposures during either the annual or long-term average silking period. Consistent with our hypothesis and physical understanding, yield anomalies were more correlated with temperature exposures during the actual, rather than the long-term average, silking period. Nevertheless, temperature exposures alone explained a relatively low proportion of the yield variability, indicating that other factors and/or time periods are also important. We next investigated the potential of using remotely sensed land surface phenology instead of NASS progress data to retrieve crop growth stages, but encountered challenges related to crop type mapping and subpixel crop heterogeneity. Here, we discuss the potential of overcoming these challenges and the general utility of remotely sensed land surface phenology in crop yield mapping.

  2. Coiling of yield stress fluids

    NARCIS (Netherlands)

    Y. Rahmani; M. Habibi; A. Javadi; D. Bonn

    2011-01-01

    We present an experimental investigation of the coiling of a filament of a yield stress fluid falling on a solid surface. We use two kinds of yield stress fluids, shaving foam and hair gel, and show that the coiling of the foam is similar to the coiling of an elastic rope. Two regimes of coiling (el

  3. Yield gaps in oil palm

    NARCIS (Netherlands)

    Woittiez, Lotte S.; Wijk, van Mark T.; Slingerland, Maja; Noordwijk, van Meine; Giller, Ken E.

    2017-01-01

    Oil palm, currently the world's main vegetable oil crop, is characterised by a large productivity and a long life span (≥25 years). Peak oil yields of 12 t ha−1 yr−1 have been achieved in small plantations, and maximum theoretical yields as calculated with simulation models are 18.5 t oil ha−1 yr−1,

  4. Breeding for Grass Seed Yield

    DEFF Research Database (Denmark)

    Boelt, Birte; Studer, Bruno

    2010-01-01

    Seed yield is a trait of major interest for many fodder and amenity grass species and has received increasing attention since seed multiplication is economically relevant for novel grass cultivars to compete in the commercial market. Although seed yield is a complex trait and affected...... by agricultural practices as well as environmental factors, traits related to seed production reveal considerable genetic variation, prerequisite for improvement by direct or indirect selection. This chapter first reports on the biological and physiological basics of the grass reproduction system, then highlights...... important aspects and components affecting the seed yield potential and the agronomic and environmental aspects affecting the utilization and realization of the seed yield potential. Finally, it discusses the potential of plant breeding to sustainably improve total seed yield in fodder and amenity grasses....

  5. Limitations in the Statistical Analysis of Normalised Cigarette Smoke Analyte Yield per Milligram of Nicotine Yield

    Directory of Open Access Journals (Sweden)

    Cahours X

    2014-12-01

    Full Text Available Yields of selected mainstream smoke analytes expressed per milligram of nicotine yield (nicotine ratio and ceilings on these ratios have been proposed by WHO as part of future cigarette product regulation. This paper describes the different approaches required for precision assessment, depending on whether yields or nicotine ratios are being studied. The widely used approach of assessment of yield precision is to perform a collaborative study using a standardised method. However, for assessment of ratio precision the measurement of smoke analyte and smoke nicotine yields are often not carried out on the same set of cigarettes (unpaired due to analytical constraints and therefore the statistical approach described in ISO 5725 is inappropriate due to the various replicate combinations. In this paper, the precision of ratios was computed with unpaired measurements for NNN and nicotine yield data for the CM6 monitor test piece and the Kentucky Reference 1R5F cigarette carried out during a collaborative study in 2011 (1. A sampling technique, based on the draw of the most representative ratios, has been used to evaluate the range of both estimated repeatability and reproducibility under the ISO smoking regime that might be expected when comparing data between different laboratories. This statistical evaluation highlighted that a robust estimate of repeatability and reproducibility could not be determined for ratios obtained with unpaired measurements, using the method defined by ISO5725-2.

  6. Identification of QTL-s for drought tolerance in maize, II: Yield and yield components

    Directory of Open Access Journals (Sweden)

    Nikolić Ana

    2013-01-01

    Full Text Available Grain yield is the primary trait of interest in maize breeding programs. Worldwide, drought is the most pervasive limitation to the achievement of yield potential in maize. Drought tolerance of maize has been considerably improved through conventional breeding. Traditional breeding methods have numerous limitations, so development of new molecular genetics techniques could help in elucidation of genetic basis of drought tolerance .In order to map QTLs underlying yield and yield components under drought 116 F3 families of DTP79xB73 cross were evaluated in the field trials. Phenotypic correlations calculated using Pearson’s coefficients were high and significant. QTL detection was performed using composite interval mapping option in WinQTL Cartographer v 2.5. Over all nine traits 45 QTLs were detected: five for grain yield per plant and 40 for eight yield components. These QTLs were distributed on all chromosomes except on chromosome 9. Percent of phenotypic variability determined for the identified QTLs for all the traits was in the range from 27.46 to 95.85%. Different types of gene action were found for the QTLs identified for analyzed traits. [Projekat Ministarstva nauke Republike Srbije, br. TR31068

  7. Correlações entre atributos químicos do solo e atributos da cultura e da produtividade de arroz irrigado determinadas com técnicas de manejo localizado Correlations between soil chemical attributes and flooded rice yield through the site-specific management techniques

    Directory of Open Access Journals (Sweden)

    Reges Durigon

    2009-12-01

    Full Text Available O sistema de agricultura tradicional desconsidera a variabilidade espacial dos atributos dos solos utilizados na produção vegetal, enquanto que o manejo localizado visa a identificar e propor o manejo dessa variabilidade. Com o objetivo de determinar as correlações entre atributos de solo, da cultura e produtividade de arroz irrigado por meio de técnicas de manejo localizado, foi conduzido um experimento de 70ha. A malha de amostragem de solo utilizada foi de um ponto por hectare, e os resultados da análise de solo foram usados para elaborar os mapas de atributos químicos do solo. A amostragem para determinação do rendimento de grãos foi realizada em malha de um hectare, por meio da coleta manual de quatro subamostras de plantas por ponto georreferenciado. A variabilidade espacial e as correlações entre mapas de atributos de solo e produtividade de arroz irrigado foram geradas por meio do Software Campeiro 6.0. As maiores correlações positivas entre produtividade de arroz e atributos de solo foram verificadas para cálcio e magnésio, enquanto a saturação de alumínio apresentou a maior correlação negativa.The traditional agricultural system disregards spatial variability of the attributes of soil used in crop production, while the site-specific management aims to identify and to propose a management of this variability. An experiment of 70ha was conducted with the purpose of determining the correlation between soil attributes, of crop and flooded rice yield through site-specific management techniques. It was collected one sample per hectare, and the soil analysis results were used to elaborate the map of its chemical attributes. The sampling to determne the grain yield was made in a grid with one point per hectare and four plant sub-samples per point georreferenced were hand plucked. The spatial variability and the correlations between soil attribute maps and flooded rice yield were done using the Campeiro Software 6.0. The

  8. [Frameless stereotactic biopsy: diagnostic yield and complications].

    Science.gov (United States)

    Castle, Maria; Nájera, Edinson; Samprón, Nicolas; Bollar, Alicia; Urreta, Iratxe; Urculo, Enrique

    2014-01-01

    The aim of this study was to evaluate the variables that could modify the diagnostic yield of frameless stereotactic biopsy, as well as its complications. This was a retrospective study of frameless stereotactic biopsies carried out between July 2008 and December 2011 at Donostia University Hospital. The variables studied were size, distance to the cortex, contrast uptake and location. A total of 70 patients were included (75 biopsies); 39 males and 31 females with an age range between 39 and 83 years. The total diagnostic yield in our series was 97.1%. For lesions >19mm, the technique offered a sensitivity of 95.2% (95% CI: 86.9-98.4) and specificity of 57.1% (95% CI: 25.0-84.2). The yield was lower for lesions within 17mm of the cortex: sensitivity of 74.6% (95% CI: 62.1-84.7) and specificity of 71.4% (95% CI: 29.0-96.3). Seven (10%) patients developed complications after the first biopsy and none after the second. The diagnostic yield was lower for lesions less than 2cm in size and located superficially. In this series we did not observe an increased rate of complications after a second biopsy. Copyright © 2013 Sociedad Española de Neurocirugía. Published by Elsevier España. All rights reserved.

  9. 利用脉冲激光技术研究哺乳动物碳氧血红蛋白光解量子产率%Quantum yields in photolyses of mammalian carboxy-hemoglobin studied by pulsed laser pump-probe technique

    Institute of Scientific and Technical Information of China (English)

    赵瑾瑜; 渠敏; 李家璜; 张铮; 张淑仪; 水修基; 杨跃涛; 华子春

    2011-01-01

    本文利用脉冲光解法测量了哺乳动物碳氧血红蛋白的光解反应的量子产率.脉冲光解法是利用一束波长为532 nm、脉冲宽度为8 ns、重复频率为10 Hz的脉冲激光照射碳氧血红蛋白溶液,使其发生光解反应.考虑到碳氧血红蛋白溶液和其光解产物脱氧血红蛋白的光吸收系数不同,可利用另一束波长为432 nm的连续激光检测溶液在光解前、后的透射率的变化,以测定溶液的光解量子产率.利用此实验系统,对人、猪、牛、马和兔等5种哺乳动物的碳氧血红蛋白的光解量子产率进行了测量和研究,结果表明,不同物种的光解量子产率各不相同,其中猪、牛、马的碳氧血红蛋白的光解量子产率很接近,兔的碳氧血红蛋白的光解量子产率与其他物种的差异最大.最后,对测量的结果从血红蛋白的氨基酸序列、氢键和盐桥排布、四级结构等方面进行了分析与讨论.%Hemoglobin (Hb) as the allosteric protein, in photo-dissociations of liganded Hb has been studied widely. The mechanisms describing the cooperative binding of CO and other ligands to hemoglobins has been the subject of extensive studies as an important fundamental problem for a long time. In this paper, the quantum yields in photolyses of carboxy-hemoglobins (HbCO) of mammals, such as human,pig, bovine, horse and rabbit, are investigated by the optical pump-probe technique, in which the quantum yield is defined as the molecular number of photoproduct species divided by the absorbed photon number. In the optical pump-probe technique, the HbCO of the mammals are irradiated by a pulsed pumping laser beam with the wavelength 532 nm, pulse width 8 ns and the repetition frequency 10 Hz, then the HbCO is photo-dissociated.Meanwhile, another continuous optical beam with the wavelength 432 nm is used as a probe beam to detect the absorbance change induced by the photo-dissociation before and after the laser pulse illuminating

  10. YIELD AND YIELD COMPONENTS OF INVESTIGATED RAPESEED HYBRIDS AND CULTIVARS

    Directory of Open Access Journals (Sweden)

    Milan Pospišil

    2014-06-01

    Full Text Available To evaluate new winter rapeseed hybrids and cultivars, investigations were conducted at the experimental field of the Faculty of Agriculture, University of Zagreb, in the period 2009/10 - 2011/12. The trial involved 11 hybrids and 5 cultivars rapeseed of 5 seed producers selling seed in Croatia. The studied rapeseed hybrids and cultivars differed significantly in seed and oil yields, oil content and yield components (seed number per silique and 1000 seed weight. However, a number of hybrids rendered identical results, since the differences in the investigated properties were within statistically allowable deviation. Hybrids Traviata and CWH 119 can be singled out based on the achieved seed and oil yields, and the cultivar Ricco and hybrids CWH 119 and PR46W15 for their high oil content in seed. Hybrids with a larger silique number per plant also achieved a higher seed yield.

  11. Interdependence of yield and yield components of confectionary sunflower hybrids

    OpenAIRE

    Hladni Nada; Jocić Siniša; Miklič Vladimir; Saftić-Panković Dejana; Kraljević-Balalić Marija

    2011-01-01

    The two most important criteria for introducing new confectionary hybrids into production are high seed and protein yield. That is why it is important to find the traits that are measurable, and that at the same time show a strong correlation with seed and protein yield, so that they can be used as a criteria for confectionary hybrid breeding. Results achieved during 2008 at the locations Rimski Sancevi (Region of Vojvodina) and Kula (Central Serbia) show t...

  12. Grapevine canopy reflectance and yield

    Science.gov (United States)

    Minden, K. A.; Philipson, W. R.

    1982-01-01

    Field spectroradiometric and airborne multispectral scanner data were applied in a study of Concord grapevines. Spectroradiometric measurements of 18 experimental vines were collected on three dates during one growing season. Spectral reflectance, determined at 30 intervals from 0.4 to 1.1 microns, was correlated with vine yield, pruning weight, clusters/vine, and nitrogen input. One date of airborne multispectral scanner data (11 channels) was collected over commercial vineyards, and the average radiance values for eight vineyard sections were correlated with the corresponding average yields. Although some correlations were significant, they were inadequate for developing a reliable yield prediction model.

  13. 杂交稻新品种Ⅱ优5928亲本特征特性及高产制种技术%Parent Characteristics and High-yield Seed Production Techniques for New Late Indica Hybrid Rice Combination , Ⅱ you 5928

    Institute of Scientific and Technical Information of China (English)

    谢建平; 徐淑英

    2012-01-01

    Ⅱ You 5928 is a late indica hybrid rice combination derived from CMS line Ⅱ-32A and restore line longhui 5928 by Longyan Agricultural institution,Fujian province,and authorized by the Fujian Provincial Crop Variety Approval Committee in 2008.The characteristics of the combination was high yield,disease resistance,wide adaptability,high seed production.The parental characteristics and seed production techniques were summarized in the paper.%Ⅱ优5928是福建省龙岩市农科所用不育系Ⅱ-32A与自育恢复系龙恢5928配组育成的晚籼杂交稻新品种,2008年通过福建省农作物品种审定。具有产量高、抗病性强、广适性好、制种产量高等特色优势性状。概括了Ⅱ优5928亲本的特征特性,总结了该品种的高产制种技术。

  14. Multiaxial yield behaviour of polypropylene

    Directory of Open Access Journals (Sweden)

    Lang R.

    2010-06-01

    Full Text Available In order to characterize the yield behavior of polypropylene as a function of pressure and to verify the applicability of the Drucker-Prager yield function, various tests were conducted to cover a wide range of stress states from uniaxial tension and compression to multiaxial tension and confined compression. Tests were performed below and above the glass transition temperature, to study the combined effect of pressure and temperature. The pressure sensitivity coefficient as an intrinsic material parameter was determined as a function of temperature. Increasing pressure sensitivity values were found with increasing temperature, which can be related to the change in the free volume and thus, to the enhanced molecular mobility. A best-fit Drucker-Prager yield function was applied to the experimental yield stresses and an average error between the predictions and the measurements of 7 % was obtained.

  15. Effect of biofertilizers on yield and yield components of cucumber

    Directory of Open Access Journals (Sweden)

    Faranak Moshabaki Isfahani

    2012-01-01

    Full Text Available Biofertilizer is defined as a substance which contains living organisms which, when applied to seed, plant surface, or soil, colonize the rhizosphere or interior of the plant and promote growth by increasing the supply or availability of primary nutrients to the host plant. Biofertilizers are well recognized as an important component of integrated plant nutrient management for sustainable agriculture and hold a great promise improve crop yield. The present study for the sake of evaluating the use of plant growth promoting rhizobacteria produced by Pseudomonas sp. and phosphate bio fertilizers produced by Pseudomonas putida strain P13 and Pantoea agglomerans strain P5 and chemical fertilizers in the separate treatments on yield and yield components of cucumber by using a factorial experiment in completely randomized block design with three repetition were performed in the field. The symbol of P represents chemical fertilizer by amount of respectively (0, 25%, 50%, 75%, 100%, B1 shows plant growth promoting rhizobacteria (PGPR and B2 indicates bio fertilizer-2. The results showed that P1B0 has the most yield, and control treatments has the least yield. P100B1 has the most length of plant and P100B0 has the least length of plant, P25B1 has the most amount of chlorophyll and P75B2 has the least chlorophyll. P75B2 has the most shoots dry weight and P100B0 has the least shoots dry weight. B1P50 has the most shoots fresh weight and P25B2 has the least shoots fresh weight. B1P50 has the most roots dry weight and P100B0 has the least roots dry weight. B1P50 has the most roots fresh weight and P25B2 has the least roots fresh weight. So the results indicate that use of biological fertilizers have caused increase yield and components yield of cucumber.

  16. Ethiopian Wheat Yield and Yield Gap Estimation: A Spatial Small Area Integrated Data Approach

    Science.gov (United States)

    Mann, M.; Warner, J.

    2015-12-01

    Despite the collection of routine annual agricultural surveys and significant advances in GIS and remote sensing products, little econometric research has been undertaken in predicting developing nation's agricultural yields. In this paper, we explore the determinants of wheat output per hectare in Ethiopia during the 2011-2013 Meher crop seasons aggregated to the woreda administrative area. Using a panel data approach, combining national agricultural field surveys with relevant GIS and remote sensing products, the model explains nearly 40% of the total variation in wheat output per hectare across the country. The model also identifies specific contributors to wheat yields that include farm management techniques (eg. area planted, improved seed, fertilizer, irrigation), weather (eg. rainfall), water availability (vegetation and moisture deficit indexes) and policy intervention. Our findings suggest that woredas produce between 9.8 and 86.5% of their potential wheat output per hectare given their altitude, weather conditions, terrain, and plant health. At the median, Amhara, Oromiya, SNNP, and Tigray produce 48.6, 51.5, 49.7, and 61.3% of their local attainable yields, respectively. This research has a broad range of applications, especially from a public policy perspective: identifying causes of yield fluctuations, remotely evaluating larger agricultural intervention packages, and analyzing relative yield potential. Overall, the combination of field surveys with spatial data can be used to identify management priorities for improving production at a variety of administrative levels.

  17. Experimental techniques; Techniques experimentales

    Energy Technology Data Exchange (ETDEWEB)

    Roussel-Chomaz, P. [GANIL CNRS/IN2P3, CEA/DSM, 14 - Caen (France)

    2007-07-01

    This lecture presents the experimental techniques, developed in the last 10 or 15 years, in order to perform a new class of experiments with exotic nuclei, where the reactions induced by these nuclei allow to get information on their structure. A brief review of the secondary beams production methods will be given, with some examples of facilities in operation or under project. The important developments performed recently on cryogenic targets will be presented. The different detection systems will be reviewed, both the beam detectors before the targets, and the many kind of detectors necessary to detect all outgoing particles after the reaction: magnetic spectrometer for the heavy fragment, detection systems for the target recoil nucleus, {gamma} detectors. Finally, several typical examples of experiments will be detailed, in order to illustrate the use of each detector either alone, or in coincidence with others. (author)

  18. GROUP PROFILE Computer Technique

    Directory of Open Access Journals (Sweden)

    Andrey V. Sidorenkov

    2015-01-01

    Full Text Available This article contains a description of the structure, the software and functional capabilities, and the scope and purposes of application of the Group Profile (GP computer technique. This technique rests on a conceptual basis (the microgroup theory, includes 16 new and modified questionnaires, and a unique algorithm, tied to the questionnaires, for identification of informal groups. The GP yields a wide range of data about the group as a whole (47 indices, each informal group (43 indices, and each group member (16 indices. The GP technique can be used to study different types of groups: production (work groups, design teams, military units, etc., academic (school classes, student groups, and sports.

  19. Maximized ExoEarth Candidate Yields for Starshades

    CERN Document Server

    Stark, Christopher C; Lisman, Doug; Cady, Eric; Savransky, Dmitry; Roberge, Aki; Mandell, Avi M

    2016-01-01

    The design and scale of a future mission to directly image and characterize potentially Earth-like planets will be impacted, to some degree, by the expected yield of such planets. Recent efforts to increase the estimated yields, by creating observation plans optimized for the detection and characterization of Earth-twins, have focused solely on coronagraphic instruments; starshade-based missions could benefit from a similar analysis. Here we explore how to prioritize observations for a starshade given the limiting resources of both fuel and time, present analytic expressions to estimate fuel use, and provide efficient numerical techniques for maximizing the yield of starshades. We implemented these techniques to create an approximate design reference mission code for starshades and used this code to investigate how exoEarth candidate yield responds to changes in mission, instrument, and astrophysical parameters for missions with a single starshade. We find that a starshade mission operates most efficiently so...

  20. Maximum energy yield approach for CPV tracker design

    Science.gov (United States)

    Aldaiturriaga, E.; González, O.; Castro, M.

    2012-10-01

    Foton HC Systems has developed a new CPV tracker model, specially focused on its tracking efficiency and the effect of the tracker control techniques on the final energy yield of the system. This paper presents the theoretical work carried out into determining the energy yield for a CPV system, and illustrates the steps involved in calculating and understanding how energy consumption for tracking is opposed to tracker pointing errors. Additionally, the expressions to compute the optimum parameters are presented and discussed.

  1. Yield statistics of interpolated superoscillations

    Science.gov (United States)

    Katzav, Eytan; Perlsman, Ehud; Schwartz, Moshe

    2017-01-01

    Yield optimized interpolated superoscillations have been recently introduced as a means for possibly making the use of the phenomenon of superoscillation practical. In this paper we study how good is a superoscillation that is not optimal. Namely, by how much is the yield decreased when the signal departs from the optimal one. We consider two situations. One is the case where the signal strictly obeys the interpolation requirement and the other is when that requirement is relaxed. In the latter case the yield can be increased at the expense of deterioration of signal quality. An important conclusion is that optimizing superoscillations may be challenging in terms of the precision needed, however, storing and using them is not at all that sensitive. This is of great importance in any physical system where noise and error are inevitable.

  2. Compression paddle tilt correction in full-field digital mammograms.

    NARCIS (Netherlands)

    Kallenberg, M.G.J.; Karssemeijer, N.

    2012-01-01

    During the acquisition of a mammogram the breast is compressed between the compression paddle and the support table. When compression is applied, the upper plate is tilted which results in variation in breast thickness from the chest wall to the breast margin. Variation in breast thickness influence

  3. Vortex ring state by full-field actuator disc model

    Energy Technology Data Exchange (ETDEWEB)

    Soerensen, J.N.; Shen, W.Z.; Munduate, X. [DTU, Dept. of Energy Engineering, Lyngby (Denmark)

    1997-08-01

    One-dimensional momentum theory provides a simple analytical tool for analysing the gross flow behavior of lifting propellers and rotors. Combined with a blade-element strip-theory approach, it has for many years been the most popular model for load and performance predictions of wind turbines. The model works well at moderate and high wind velocities, but is not reliable at small wind velocities, where the expansion of the wake is large and the flow field behind the rotor dominated by turbulent mixing. This is normally referred to as the turbulent wake state or the vortex ring state. In the vortex ring state, momentum theory predicts a decrease of thrust whereas the opposite is found from experiments. The reason for the disagreement is that recirculation takes place behind the rotor with the consequence that the stream tubes past the rotor becomes effectively chocked. This represents a condition at which streamlines no longer carry fluid elements from far upstream to far downstream, hence one-dimensional momentum theory is invalid and empirical corrections have to be introduced. More sophisticated analytical or semi-analytical rotor models have been used to describe stationary flow fields for heavily loaded propellers. In recent years generalized actuator disc models have been developed, but up to now no detailed computations of the turbulent wake state or the vortex ring state have been performed. In the present work the phenomenon is simulated by direct simulation of the Navier-Stokes equations, where the influence of the rotor on the flow field is modelled simply by replacing the blades by an actuator disc with a constant normal load. (EG) 13 refs.

  4. 浙江省西红花“二段法”优质高产栽培技术研究%High-quality and High-yield Cultivation Technique of Two Segments Method for Crocus sativus L.in Zhejiang Province

    Institute of Scientific and Technical Information of China (English)

    饶君凤; 王根法; 吕伟德

    2012-01-01

    通过西红花栽培研究试验及示范推广,作者对西红花的药用价值、特征特性、栽培技术、田间管理、病虫害防治及采收加工进行了系统的研究,提出浙江省西红花“二段法”栽培的技术措施.西红花在浙江高产栽培的关键是选用8g以上的种球,11月上中旬田间露地种植,在科学的肥水运筹下越冬生长并发育形成新的子球,翌年5月植株休眠将商品用球采收放到室内通风阴湿的环境下催芽,10月底到11月采花.这套技术的推广应用为浙江省西红花产业发展及栽培管理提供了科学依据.%Based on the cultivation test and demonstration, the characteristics, medicinal value, cultivation technique, field management, pest control, harvest and process of Crocus sativus L. Were analyzed systemically. Two Segments Method for the cultivation of C. Sativus in Zhejiang Province was put forward. Selecting bulbs above 8 g was the key for high-yield cultivation of C. Sativus in Zhejiang Province. In early November, C. Sativus was cultivated in the open field, and grew over winter under scientific application of fertilizer and water. In the following May, bulbs were collected in ventilating, shady and humid room to accelerate germination. Flowers were collected from late October to November. Popularization of this matching technique provided scientific guidance for the industrial development and cultivation management of C. Sativus.

  5. Compression Enhanced Shear Yield Stress of Electrorheological Fluid

    Institute of Scientific and Technical Information of China (English)

    ZHANG Min-Liang; TIAN Yu; JIANG Ji-Le; ZHU Xu-Li; MENG Yong-Gang; WEN Shi-Zhu

    2009-01-01

    @@ Shear tests of an electrorheological fluid with pre-applied electric field and compression along the field direction are carried out. The results show that pre-compressions can increase the shear yield stress up to ten times. Under the same external electric field strength, a higher compressive strain corresponds to a larger shear yield stress enhancement but with slight current density decrease, which shows that the particle interaction potentials are not increased by compressions but the compression-induced chain aggregation dominates the shear yield stress improvement. This pre-compression technique might be useful [or developing high performance flexible ER or magnetorheological couplings.

  6. Specific yield, High Plains aquifer

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This raster data set represents specific-yield ranges in the High Plains aquifer of the United States. The High Plains aquifer underlies 112.6 million acres (176,000...

  7. Assessing potential sustainable wood yield

    Science.gov (United States)

    Robert F. Powers

    2001-01-01

    Society is making unprecedented demands on world forests to produce and sustain many values. Chief among them is wood supply, and concerns are rising globally about the ability of forests to meet increasing needs. Assessing this is not easy. It requires a basic understanding of the principles governing forest productivity: how wood yield varies with tree and stand...

  8. Genetic progress in Dutch crop yields

    NARCIS (Netherlands)

    Rijk, H.C.A.; Ittersum, van M.K.; Withagen, J.C.M.

    2013-01-01

    Crop yields are a result of interactions between genetics, environment and management (G × E × M). As in the Netherlands differences between potential yield and actual farm yields (yield gaps) are relatively small, progress in genetic potential is essential to further increase farm yields. In this p

  9. Yield estimation of metallic layers in integrated circuits

    Institute of Scientific and Technical Information of China (English)

    Wang Jun-Ping; Hao Yue; Zhang Jun-Ming

    2007-01-01

    In the existing models of estimating the yield and critical area, the defect outline is usually assumed to be circular, but the observed real defect outlines are irregular in shape. In this paper, estimation of the yield and critical area is made using the Monte Carlo technique and the relationship between the errors of yield estimated by circular defect and the rectangle degree of the defect is analysed. The rectangular model of a real defect is presented, and the yield model is provided correspondingly. The models take into account an outline similar to that of an original defect, the characteristics of two-dimensional distribution of defects, the feature of a layout routing, and the character of yield estimation. In order to make the models practicable, the critical area computations related to rectangular defect and regular (vertical or horizontal) routing are discussed. The critical areas associated with rectangular defect and non-regular routing are developed also, based on the mathematical morphology. The experimental results show that the new yield model may predict the yield caused by real defects more accurately than the circular model. It is significant that the yield is accurately estimated using the proposed model for 1C metals.

  10. Breeding and Cultivation Techniques of a New Sweet Potato Variety'Langyanshu 6'with High Yield and Good Quality%高产优质甘薯新品种'廊烟薯6'选育及栽培技术

    Institute of Scientific and Technical Information of China (English)

    揭琴; 张恭; 杜德玉; 辛国胜; 田金玉

    2016-01-01

    In order to meet the market need for special sweet potato varieties, promote the development of sweet potato industry in Hebei Province, a new sweet potato variety'Langyanshu 6'with high yield and good quality was bred by Langfang Academy of Agriculture and Forestry Science. Its female parent was the elite line'06-20'selected by Yantai Academy of Agricultural Sciences and the male parent was mixed pollens from 7 varieties,'Yushu 868','Yanshu 22','Luoxushu 8','Shangshu 7','Mixuan 1', and'Zhongtai 9'. This variety had the characteristics of good sprout capacity, long tendril, more branches, concentrated storage roots, white and smooth chips, good taste, root rot resistance and good storage quality. It passed the new variety identification organized by the Achievement Transformation Centre of Hebei Department of Science and Technology in January, 2014, and named as'Langyanshu 6'. The cultivation techniques of this high yield variety were developed. Test showed that the variety was a dual-purpose breed for starch and fresh edible, and had a prominent advantage in production, conformed to the breeding goals of food safety, product quality and production efficiency.%为了满足高产优质甘薯品种的市场需求,推动河北省甘薯产业的发展,廊坊市农林科学院以烟台农科院筛选的优良品系'06-20'为母本,'豫薯868'、'烟薯22'、'烟薯24'、'漯徐薯8号'、'商薯7号'、'密选1号''、中泰9号'等7个亲本作父本进行混合授粉杂交选育出高产优质甘薯新品种——'廊烟薯6'.该品种萌芽性好,长蔓,分枝数多,结薯集中,薯块大小整齐,薯干较洁白平整,食味较好,抗根腐病,贮藏性较好.2014年1月通过河北省科技厅组织的专家鉴定,定名为'廊烟薯6'.通过研究建立了该品种的高效栽培技术.试验表明,该品种是淀粉和鲜食兼用型品种,在生产上具有突出优势,符合食用安全、产品优质、生产高效的育种目标.

  11. Yield Response and Economics of Shallow Subsurface Drip Irrigation Systems

    Science.gov (United States)

    Field tests were conducted using shallow subsurface drip irrigation (S3DI) on cotton (Gossypium hirsutum, L.), corn (Zea mays, L.), and peanut (Arachis hypogeae, L.) in rotation to investigate yield potential and economic sustainability of this irrigation system technique over a six year period. Dri...

  12. Geoelectrical parameter-based multivariate regression borehole yield model for predicting aquifer yield in managing groundwater resource sustainability

    Directory of Open Access Journals (Sweden)

    Kehinde Anthony Mogaji

    2016-07-01

    Full Text Available This study developed a GIS-based multivariate regression (MVR yield rate prediction model of groundwater resource sustainability in the hard-rock geology terrain of southwestern Nigeria. This model can economically manage the aquifer yield rate potential predictions that are often overlooked in groundwater resources development. The proposed model relates the borehole yield rate inventory of the area to geoelectrically derived parameters. Three sets of borehole yield rate conditioning geoelectrically derived parameters—aquifer unit resistivity (ρ, aquifer unit thickness (D and coefficient of anisotropy (λ—were determined from the acquired and interpreted geophysical data. The extracted borehole yield rate values and the geoelectrically derived parameter values were regressed to develop the MVR relationship model by applying linear regression and GIS techniques. The sensitivity analysis results of the MVR model evaluated at P ⩽ 0.05 for the predictors ρ, D and λ provided values of 2.68 × 10−05, 2 × 10−02 and 2.09 × 10−06, respectively. The accuracy and predictive power tests conducted on the MVR model using the Theil inequality coefficient measurement approach, coupled with the sensitivity analysis results, confirmed the model yield rate estimation and prediction capability. The MVR borehole yield prediction model estimates were processed in a GIS environment to model an aquifer yield potential prediction map of the area. The information on the prediction map can serve as a scientific basis for predicting aquifer yield potential rates relevant in groundwater resources sustainability management. The developed MVR borehole yield rate prediction mode provides a good alternative to other methods used for this purpose.

  13. Diversification, Yield and a New Agricultural Revolution: Problems and Prospects

    Directory of Open Access Journals (Sweden)

    Lauren C. Ponisio

    2016-11-01

    Full Text Available The sustainability of society hinges on the future of agriculture. Though alternatives to unsustainable, high-input industrial agriculture are available, agricultural systems have been slow to transition to them. Much of the resistance to adopting alternative techniques stems from the perceived costs of alternative agriculture, mainly in terms of yields. The general assumption is that agriculture that is less harmful to people and wildlife directly will be indirectly more harmful because of yield losses that lead to food shortages in the short-term and agricultural extensification in the long-term. Though the yield gap between industrial and alternative forms of agriculture is often discussed, does industrial agriculture actually produce the highest yields? In addition, to what aspects of the food system is yield relevant? We review the evidence for differences in crop yields between industrial and alternative systems and then evaluate the contribution of yields in determining whether people are fed, the land in production, and practices farmers will adopt. In both organic and conservation agriculture, different combinations of crops, climate and diversification practices outperformed industrial agriculture, and thus we find little evidence that high input systems always outperform alternative forms of agriculture. Yield, however, is largely irrelevant to determining whether people are fed or the amount of land in production. A focus on increasing yields alone to feed the world or protect biodiversity will achieve neither goal. To promote sustainable agriculture, we must move past focusing on these oversimplified relationships to disentangling the complex social and ecological factors, and determine how to provide adequate nutrition for people while protecting biodiversity.

  14. Binomial lattice for pricing Asian options on yields

    Institute of Scientific and Technical Information of China (English)

    杨德生

    2003-01-01

    An efficient binomial lattice for pricing Asian options on yields is established under the affine term structure model. In order to reconnect the path of the discrete lattice,the technique of D. Nelson and K. Ramaswamy is used to transform a stochastic interest rate process into a stochastic diffusion with unit volatility. By the binomial lattice and linear interpolation,the prices of Asian options on yields can be obtained. As the number of nodes in the tree structure grows linearly with the number of time steps, the computational speed is improved. The numerical experiments to verify the validity of the lattice are also provided.

  15. Measuring the effects of extreme weather events on yields

    Directory of Open Access Journals (Sweden)

    J.P. Powell

    2016-06-01

    Full Text Available Extreme weather events are expected to increase worldwide, therefore, anticipating and calculating their effects on crop yields is important for topics ranging from food security to the economic viability of biomass products. Given the local nature of weather, particularly precipitation, effects are best measured at a local level. This paper analyzes weather events at the level of the farm for a specific crop, winter wheat. Once it has been established that extreme events are expected to continue occurring at historically high levels for farming locations throughout the Netherlands, the effects of those events on wheat yields are estimated while controlling for the other major input factors affecting yields. Econometric techniques are applied to an unbalanced panel data set of 334 farms for a period of up to 12 years. Analyzes show that the number of days with extreme high temperatures in Dutch wheat growing regions has significantly increased since the early 1900s, while the number of extreme low temperature events has fallen over that same period. The effects of weather events on wheat yields were found to be time specific in that the week in which an event occurred determined its effect on yields. High temperature events and precipitation events were found to significantly decrease yields.

  16. Influence of Bark Pyrolysis Technology on Yield

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yong; YAN Zhen; LIU Yurong; WANG Shu

    2006-01-01

    With the self-made pyrolysis equipment in miniature,we experimented in different pyrolysis conditions to get different pyrolyzate yields (carbon,vinegar and gas).It proved that with the rise of temperature,the average yield of carbon descends gradually while the yields of vinegar and gas rise gradually.As the temperature rises,the yield of gas increases much more than that of vinegar.When speeding up the rising temperature,yield of carbon goes down while yields of vinegar and gas go up.

  17. Optical measurement techniques - A push for digitization

    Science.gov (United States)

    Kulkarni, Rishikesh; Rastogi, Pramod

    2016-12-01

    Over the years, optical measurement techniques have been the problem-solving backbone of many engineering applications such as nondestructive testing of materials, measurement of various material properties, structural analysis and experimental mechanics [1-3]. Probably the most important advantage associated with any optical measurement system over other systems is its non-contact type of measurement capability. Apart from their non-contact nature, the optical measurement systems are capable of providing full-field measurements at scales ranging from milli-meters to nano-meters.

  18. Yield and yield gaps in central U.S. corn production systems

    Science.gov (United States)

    The magnitude of yield gaps (YG) (potential yield – farmer yield) provides some indication of the prospects for increasing crop yield. Quantile regression analysis was applied to county maize (Zea mays L.) yields (1972 – 2011) from Kentucky, Iowa and Nebraska (irrigated) (total of 115 counties) to e...

  19. Phenomenology of muon-induced neutron yield

    Science.gov (United States)

    Malgin, A. S.

    2017-07-01

    The cosmogenic neutron yield Yn characterizes the ability of matter to produce neutrons under the effect of cosmic ray muons with spectrum and average energy corresponding to an observation depth. The yield is the basic characteristic of cosmogenic neutrons. The neutron production rate and neutron flux both are derivatives of the yield. The constancy of the exponents α and β in the known dependencies of the yield on energy Yn∝Eμα and the atomic weight Yn∝Aβ allows one to combine these dependencies in a single formula and to connect the yield with muon energy loss in matter. As a result, the phenomenological formulas for the yields of muon-induced charged pions and neutrons can be obtained. These expressions both are associated with nuclear loss of the ultrarelativistic muons, which provides the main contribution to the total neutron yield. The total yield can be described by a universal formula, which is the best fit of the experimental data.

  20. Definitions of radioisotope thick target yields

    Energy Technology Data Exchange (ETDEWEB)

    Otuka, Naohiko [International Atomic Energy Agency, Wien (Austria). Nuclear Data Section; Takacs, Sandor [Hungarian Academy of Science, Debrecen (Hungary). Inst. of Nuclear Research

    2015-05-01

    Definitions of thick target yields are reviewed in relation to their documentation for the experimental nuclear reaction data library (database). Researchers reporting experimental thick target yields are urged to define their yields clearly with an appropriate unit in order to compile them in the experimental data library (EXFOR) in a consistent manner, and also to properly utilise them for comparison with other experimental and evaluated yields.

  1. GDP growth and the yield curvature

    DEFF Research Database (Denmark)

    Møller, Stig Vinther

    2014-01-01

    This paper examines the forecastability of GDP growth using information from the term structure of yields. In contrast to previous studies, the paper shows that the curvature of the yield curve contributes with much more forecasting power than the slope of yield curve. The yield curvature also...... predicts bond returns, implying a common element to time-variation in expected bond returns and expected GDP growth....

  2. Analysis of yield advantage in mixed cropping

    NARCIS (Netherlands)

    Ranganathan, R.

    1993-01-01

    It has long been recognized that mixed cropping can give yield advantages over sole cropping, but methods that can identify such yield benefits are still being developed. This thesis presents a method that combines physiological and economic principles in the evaluation of yield advantage.

  3. Nodal yield in selective neck dissection

    DEFF Research Database (Denmark)

    Norling, Rikke; Therkildsen, Marianne H; Bradley, Patrick J

    2013-01-01

    The total lymph node yield in neck dissection is highly variable and depends on anatomical, surgical and pathological parameters. A minimum yield of six lymph nodes for a selective neck dissection (SND) as recommended in guidelines lies in the lower range of the reported clinical nodal yields...

  4. The Impact of Statistical Leakage Models on Design Yield Estimation

    Directory of Open Access Journals (Sweden)

    Rouwaida Kanj

    2011-01-01

    Full Text Available Device mismatch and process variation models play a key role in determining the functionality and yield of sub-100 nm design. Average characteristics are often of interest, such as the average leakage current or the average read delay. However, detecting rare functional fails is critical for memory design and designers often seek techniques that enable accurately modeling such events. Extremely leaky devices can inflict functionality fails. The plurality of leaky devices on a bitline increase the dimensionality of the yield estimation problem. Simplified models are possible by adopting approximations to the underlying sum of lognormals. The implications of such approximations on tail probabilities may in turn bias the yield estimate. We review different closed form approximations and compare against the CDF matching method, which is shown to be most effective method for accurate statistical leakage modeling.

  5. Prediction of yield by digital image analysis of vine

    Directory of Open Access Journals (Sweden)

    Bešlić Zoran S.

    2014-01-01

    Full Text Available The grape yield per vine of cv. Cabernet Sauvignon (Vitis vinifera L. was evaluated on the basis of digital image processing of vine part. Digital camera was mounted on tripod and used for taking photos of 1 x 1 m portions of canopy. The Adobe Photoshop software was used to analyse image for the colour counting of the blue pixels of grape in the quadrant region. The actual yield was obtained from the photographed vines by hand harvesting of sampled portions. Linear regression was used for calculation of the correlation between blue pixels and grape weight. The relatively strong relationship between blue pixels and grape weight (R2=0.91 was obtained. Based on these results, we can recommend this simple technique for yield forecasting. [Projekat Ministarstva nauke Republike Srbije, br. TP31063

  6. Integrated process for high conversion and high yield protein PEGylation.

    Science.gov (United States)

    Pfister, David; Morbidelli, Massimo

    2016-08-01

    Over the past decades, PEGylation has become a powerful technique to increase the in vivo circulation half-life of therapeutic proteins while maintaining their activity. The development of new therapeutic proteins is likely to require further improvement of the PEGylation methods to reach even better selectivity and yield for reduced costs. The intensification of the PEGylation process was investigated through the integration of a chromatographic step in order to increase yield and conversion for the production of mono-PEGylated protein. Lysozyme was used as a model protein to demonstrate the feasibility of such approach. In the integrated reaction/separation process, chromatography was used as fractionation technique in order to isolate and recycle the unreacted protein from the PEGylated products. This allows operating the reactor with short reaction times so as to minimize the production of multi-PEGylated proteins (i.e., conjugated to more than one polymer). That is, the reaction is stopped before the desired product (i.e., the mono-PEGylated protein) can further react, thus leading to limited conversion but high yield. The recycling of the unreacted protein was then considered to drive the protein overall conversion to completion. This approach has great potential to improve processes whose yield is limited by the further reaction of the product leading to undesirable by-products. Biotechnol. Bioeng. 2016;113: 1711-1718. © 2016 Wiley Periodicals, Inc.

  7. PREDICTION OF YIELD FUNCTIONS ON BCC POLYCRYSTALS

    Institute of Scientific and Technical Information of China (English)

    Huang Mojia; Fu Mingfu; Zheng Chaomei

    2006-01-01

    By the nonlinear optimization theory, we predict the yield function of single BCC crystals in Hill's criterion form. Then we give a formula on the macroscopic yield function of a BCC polycrystal Ω under Sachs' model, where the volume average of the yield functions of all BCC crystallites in Ω is taken as the macroscopic yield function of the BCC polycrystal. In constructing the formula, we try to find the relationship among the macroscopic yield function, the orientation distribution function (ODF), and the single BCC crystal's plasticity. An expression for the yield stress of a uniaxial tensile problem is derived under Taylor's model in order to compare the expression with that of the macroscopic yield function.

  8. Alternating Current Heating Technique of Hollow Rod

    Institute of Scientific and Technical Information of China (English)

    Na Weisheng; Shi Tonghao

    1995-01-01

    @@ In recent years, wellbore heat tracing technique is widely used in development of high viscosity and high pour point crude oil. Theory and experiences show that wellbore heat tracing has obvious effect on increasing liquid yield of oil wells.

  9. Study Characteristics of High Yield Population and Key Cultural Techniques in Rice with Bowl-seedling Mechanical-transplanting Method in North of Jiangsu Province%苏北地区麦茬钵苗机插稻高产群体特征及关键技术研究

    Institute of Scientific and Technical Information of China (English)

    张军; 王兴龙; 李必忠; 石广跃; 方书亮; 张永进; 刘忠红; 庾跃东

    2015-01-01

    In Huai'an demonstration-base of rice-wheat, Yongyou 2640 and Huaidao 11 were used as materials by seeting the high-yield demonstration test of bowl-seedling mechanical transplanted rice, with conventional blanket seedling mechanical transplanted rice for CK, the yield and population characteristics under two kinds of mechanical-transplanting methods were compared. The results showed that, comparing with conventional blanket seedling mechanical-transplanting, the seedling quality and transplanting quality of bowl-seedling mechanical transplanted rice were all significantly better than the CK, the tillers presented the characteristics of rising steadily and dropping slowly. The photosynthetic systems of bowl-seeding mechanical transplanted rice were better than CK, and the accumulation and proportion of biomass were both significantly higher than CK from heading to maturity stage, the yield of two cultivars were 5.87%and 4.02%higher than blanket seedling mechanical transplanted rice respectively.%以甬优2640和淮稻11号为试验材料,在淮安市稻麦示范基地开展钵苗机插稻高产攻关试验,同时以常规毯苗机插高产攻关方为对照,比较两种机插方式的产量构成及群体特征. 结果表明,与常规机插稻相比,钵苗机插稻秧苗素质及大田移栽效果优势明显,群体茎蘖消长平稳;钵苗机插稻生育中、后期光合系统配置优,抽穗至成熟期物质积累量和积累比例高,2品种最终实产分别高5.87%和4.02%.

  10. Acquired Techniques

    DEFF Research Database (Denmark)

    Lunde Nielsen, Espen; Halse, Karianne

    2013-01-01

    Acquired Techniques - a Leap into the Archive, at Aarhus School of Architecture. In collaboration with Karianne Halse, James Martin and Mika K. Friis. Following the footsteps of past travelers this is a journey into tools and techniques of the architectural process. The workshop will focus upon...... architectural production as a conglomerate of various analogue and digital methods, and provide the basics, the tips/tricks - and how the tool themselves becomes operational for spatial/thematic investigations. Eventually, this will become a city, exhibition and phamplet inhabited by the (by...

  11. Absolute measurement of the DT primary neutron yield on the National Ignition Facility

    Directory of Open Access Journals (Sweden)

    Leeper R.J.

    2013-11-01

    Full Text Available The measurement of the absolute neutron yield produced in inertial confinement fusion target experiments conducted on the National Ignition Facility (NIF is essential in benchmarking progress towards the goal of achieving ignition on this facility. This paper describes three independent diagnostic techniques that have been developed to make accurate and precise DT neutron yield measurements on the NIF.

  12. Influence of material quality and process-induced defects on semiconductor device performance and yield

    Science.gov (United States)

    Porter, W. A.; Mckee, W. R.

    1974-01-01

    An overview of major causes of device yield degradation is presented. The relationships of device types to critical processes and typical defects are discussed, and the influence of the defect on device yield and performance is demonstrated. Various defect characterization techniques are described and applied. A correlation of device failure, defect type, and cause of defect is presented in tabular form with accompanying illustrations.

  13. High-yielding Seed Production Techniques for Two-line Good Quality Hybrid Rice Combination Y Liangyou 5866 Planted as Post-tobacco Rice%优质两系杂交稻Y两优5866烟后高产制种技术

    Institute of Scientific and Technical Information of China (English)

    黄邵荣

    2015-01-01

    In this study, we introduced the parent,s characteristics of two-line good quality hybrid rice Y Liangyou 5866. At the same time, this paper also summarized the rice high-yielding seed production technology planted as post-tobacco rice, which contained reasonable arrangements for the parents of the sowing gap stage, cultivating more tillers seedlings, scientific field management, integrated pest management, create the parents of high yield population, scientific spraying “920”, improve the outcrossing rate, strictly to miscellaneous go bad, ensure the seed quality and so on several aspects.%介绍了优质两系杂交水稻Y两优5866亲本的特征特性,结合3a制种实践,总结其烟后高产制种技术:合理安排父母本播种差期,培育多蘖壮秧、科学田管、综合防治病虫、创建父母本高产群体,科学喷施“九二○”、提高异交结实率,严格去杂去劣、确保种子质量等几个环节。

  14. Translation Techniques

    Directory of Open Access Journals (Sweden)

    Marcia Pinheiro

    2015-05-01

    Full Text Available In this paper, we discuss three translation techniques: literal, cultural, and artistic. Literal translation is a well-known technique, which means that it is quite easy to find sources on the topic. Cultural and artistic translation may be new terms. Whilst cultural translation focuses on matching contexts, artistic translation focuses on matching reactions. Because literal translation matches only words, it is not hard to find situations in which we should not use this technique.  Because artistic translation focuses on reactions, judging the quality of an artistic translation work is one of the most difficult things one can do. We end up having a score of complexity and humanity for each one of the mentioned techniques: Literal translation would be the closest thing we have to the machines world and artistic translation would be the closest thing we have to the purely human world. By creating these classifications and studying the subtleties of each one of them, we are adding degrees of quality to our courses and to translation as a professional field. The main contribution of this paper is then the formalization of such a piece of knowledge. We, however, also lay the foundations for studies of this type.

  15. Experimental Techniques

    CERN Document Server

    Engelfried, J

    1999-01-01

    In this course we will give examples for experimental techniques used in particle physics experiments. After a short introduction, we will discuss applications in silicon microstrip detectors, wire chambers, and single photon detection in Ring Imaging Cherenkov (RICH) counters. A short discussion of the relevant physics processes, mainly different forms of energy loss in matter, is enclosed.

  16. An orientation-space super sampling technique for six-dimensional diffraction contrast tomography

    NARCIS (Netherlands)

    N. Viganò (Nicola); K.J. Batenburg (Joost); W. Ludwig (Wolfgang)

    2016-01-01

    textabstractDiffraction contrast tomography (DCT) is an X-ray full-field imaging technique that allows for the non-destructive three-dimensional investigation of polycrystalline materials and the determination of the physical and morphological properties of their crystallographic domains, called

  17. Comparison of dignity determination of mammographic microcalcification with two systems for digital full-field mammography with different detector resolution. A retrospective clinical study; Vergleich der Dignitaetsbestimmung von mammographischem Mikrokalk mit zwei Systemen zur digitalen Vollfeldmammographie unterschiedlicher Detektoraufloesung. Eine retrospektive klinische Studie

    Energy Technology Data Exchange (ETDEWEB)

    Schulz-Wendtland, R.; Adamietz, B.; Meier-Meitinger, M.; Wenkel, E.; Lell, M.; Anders, K.; Uder, M. [Universitaetsklinikum Erlangen, Abteilung Gynaekologische Radiologie, Radiologisches Institut, Erlangen (Germany); Hermann, K.P. [Universitaetsmedizin Goettingen, Abteilung Diagnostische Radiologie, Goettingen (Germany)

    2011-02-15

    The aim of this retrospective clinical study was to compare the diagnostic accuracy of the novel 50 {mu}m FFDM (full-field digital mammography) system (DR) with an established 70 {mu}m system (DR) in the differential diagnosis between benign and malignant clusters of microcalcification (n=50) (BI-RADS trademark classification 4/5) and to assess the possible incremental value of the 50 {mu}m pixel-pitch on specificity. From March 2009 to September 2009, 50 patients underwent full-field digital mammography (FFDM) (detector resolution 70 {mu}m) (Novation, Siemens, Erlangen, Germany). As there were suspicious signs of microcalcification classified with BI-RADS trademark 4/5 after diagnosis and preoperative wire localization, control images were made with the new FFDM system (detector: resolution 50 {mu}m) (Amulet, Fujifilm, Tokyo, Japan) with the same exposure parameters. The diagnosis was determined after the operation by five radiologists with different experience in digital mammography from randomly distributed mediolateral views (monitor reading) whose results were correlated with the final histology of all lesions. Histopathology revealed 19 benign and 31 malignant lesions in 50 patients after open biopsy. The results of the five readers showed a higher sensitivity of the new FFDM system (80.0%) in the ability to recognize malignant microcalcification in comparison to the established system (74.8%). The specificity (75.8 versus 71.6%) was slightly higher for the new system but hese results were not statistically significant (p<0.001). Considering the diagnostic accuracy, the new system (detector: resolution 50 {mu}m) was also slightly superior to the well-known system (detector: resolution 70 {mu}m) (80.1% versus 76.4%). Our study has shown that the new full-field digital mammography system using the novel detector compared with the already established FFDM system with respect to the assessment of microcalcification is at least equivalent. (orig.) [German] Das

  18. Yield stress determination of a physical gel

    DEFF Research Database (Denmark)

    Hvidt, Søren

    2013-01-01

    Pluronic F127 solutions form gels in water with high elastic moduli. Pluronic gels can, however, only withstand small deformations and stresses. Different steady shear and oscillatory methods traditionally used to determine yield stress values are compared. The results show that the yield stresses...... values of these gels depend on test type and measurement time, and no absolute yield stress value can be determined for these physical gels....

  19. Forecasting Exchange Rates with Commodity Convenience Yields

    OpenAIRE

    Beutler, Toni

    2012-01-01

    This paper investigates whether commodity convenience yields - the yields that accrue to the holders of physical commodities - can predict the exchange rate of commodity-exporters' currencies. Predictability is a consequence of the fact that i) convenience yields are useful predictors for commodity prices and ii) commodity currencies have a strong relationship with commodity prices. The empirical evidence indicates that there is a significant relationship between aggregate measures of conveni...

  20. Yield Mapping in Salix; Skoerdekartering av salix

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Christoffer; Gilbertsson, Mikael; Rogstrand, Gustav; Thylen, Lars

    2004-09-01

    The most common species for energy forest production is willow. Willow is able to produce a large amount of biomass in a short period of time. Growing willow has a potential to render a good financial result for the farmer if cultivated on fields with the right conditions and plenty of water. Under the right conditions growing willow can give the farmer a net income of 3,000 SEK (about 430 USD) per hectare and year, which is something that common cereal crops cannot compete with. However, this is not the common case since willow is often grown as a substitute crop on fields where cereal crop yield is low. The aim of this study was to reveal if it is possible to measure yield variability in willow, and if it is possible to describe the reasons for yield variation both within the field but also between different fields. Yield mapping has been used in conventional farming for about a decade. The principles for yield mapping are to continuously measure the yield while registering location by the use of GPS when harvesting the field. The collected data is then used to search for spatial variations within the field, and to try to understand the reasons for this variation. Since there is currently no commercial equipment for yield mapping in willow, a yield mapping system had to be developed within this project. The new system was installed on a Claas Jaguar harvester. The principle for yield mapping on the Claas Jaguar harvester is to measure the distance between the feeding rollers. This distance is correlated to the flow through the harvester. The speed and position of the machine was registered using GPS. Knowing the working width of the harvester this information was used to calculate the yield. All collected data was stored on a PDA computer. Soil samples were also collected from the yield mapped fields. This was to be able to test yield against both physical and chemical soil parameters. The result shows that it is possible to measure spatial variations of yield in

  1. Efficient prediction of (p,n) yields

    Energy Technology Data Exchange (ETDEWEB)

    Swift, D C; McNaney, J M; Higginson, D P; Beg, F

    2009-09-09

    In the continuous deceleration approximation, charged particles decelerate without any spread in energy as they traverse matter. This approximation simplifies the calculation of the yield of nuclear reactions, for which the cross-section depends on the particle energy. We calculated (p,n) yields for a LiF target, using the Bethe-Bloch relation for proton deceleration, and predicted that the maximum yield would be around 0.25% neutrons per incident proton, for an initial proton energy of 70 MeV or higher. Yield-energy relations calculated in this way can readily be used to optimize source and (p,n) converter characteristics.

  2. Food for thought: pretty good multispecies yield

    DEFF Research Database (Denmark)

    Rindorf, Anna; Dichmont, C. M.; Levin, P.S.

    2017-01-01

    that broader ecosystem, economic, and social objectives are addressed. We investigate how the principles of a “pretty good yield” range of fishing mortalities assumed to provide >95% of the average yield for a single stock can be expanded to a pretty good multispecies yield (PGMY) space and further to pretty...... good multidimensional yield to accommodate situations where the yield from a stock affects the ecosystem, economic and social benefits, or sustainability. We demonstrate in a European example that PGMY is a practical concept. As PGMY provides a safe operating space for management that adheres...

  3. Nucleosynthetic Yields from Gamma-Ray Bursts

    CERN Document Server

    Rockefeller, Gabriel; Young, Patrick; Bennett, Michael; Diehl, Steven; Herwig, Falk; Hirschi, Raphael; Hungerford, Aimee; Pignatari, Marco; Magkotsios, Georgios; Timmes, Francis X

    2008-01-01

    The "collapsar" engine for gamma-ray bursts invokes as its energy source the failure of a normal supernova and the formation of a black hole. Here we present the results of the first three-dimensional simulation of the collapse of a massive star down to a black hole, including the subsequent accretion and explosion. The explosion differs significantly from the axisymmetric scenario obtained in two-dimensional simulations; this has important consequences for the nucleosynthetic yields. We compare the nucleosynthetic yields to those of hypernovae. Calculating yields from three-dimensional explosions requires new strategies in post-process nucleosynthesis; we discuss NuGrid's plan for three-dimensional yields.

  4. Intensity techniques

    DEFF Research Database (Denmark)

    Jacobsen, Finn

    2008-01-01

    The Handbook of Signal Processing in Acoustics will compile the techniques and applications of signal processing as they are used in the many varied areas of Acoustics. The Handbook will emphasize the interdisciplinary nature of signal processing in acoustics. Each Section of the Handbook...... will present topics on signal processing which are important in a specific area of acoustics. These will be of interest to specialists in these areas because they will be presented from their technical perspective, rather than a generic engineering approach to signal processing. Non-specialists, or specialists...... from different areas, will find the self-contained chapters accessible and will be interested in the similarities and differences between the approaches and techniques used in different areas of acoustics....

  5. Zero tillage: A potential technology to improve cotton yield

    Directory of Open Access Journals (Sweden)

    Abbas Hafiz Ghazanfar

    2016-01-01

    Full Text Available Zero tillage technology revealed with no use of any soil inverting technique to grow crops. The crop plant seed is planted in the soil directly after irrigation to make the soil soft without any replenishing in soil layers. A study was conducted to evaluate cotton genotypes FH-114 and FH-142 for the consecutive three years of growing seasons from 2013-15. The seed of both genotypes was sown with two date of sowing, 1 March and 1 May of each three years of sowing under three tillage treatments (zero tillage, minimum tillage and conventional tillage in triplicate completely randomized split-split plot design. It was found from results that significant differences were recorded for tillage treatments, date of sowing, genotypes and their interactions. Multivariate analysis was performed to evaluate the yield and it attributed traits for potential of FH-114 and FH-142 cotton genotypes. The genotype FH-142 was found with higher and batter performance as compared to FH-114 under zero tillage, minimum tillage and conventional tillage techniques. The traits bolls per plant, boll weight, fibre fineness, fibre strength, plant height, cotton yield per plant and sympodial branches per plant were found as most contributing traits towards cotton yield and production. It was also found that FH-142 gives higher output in terms of economic gain under zero tillage with 54% increase as compared to conventional tillage technique. It was suggested that zero tillage technology should be adopted to improve cotton yield and quality. It was also recommended that further study to evaluate zero tillage as potential technology should be performed with different regions, climate and timing throughout the world.

  6. Breeding and high-yield culture technique of a new rape cultivar ‘ Huyou 19' with high oil content%高含油量油菜新品种‘沪油19’的选育和高产栽培技术研究

    Institute of Scientific and Technical Information of China (English)

    王伟荣; 杨立勇; 李延莉; 蒋美艳; 孙超才

    2011-01-01

    'Huyou 19',a new rape cultivar of Brassica napus with high oil content,was bred by means of multiple cross between varieties (lines) .being 0.1% in erucic acid content, 18. 87 /zmol/g in glucosinolate content and 49.16% in rapeseed oil content. In the Shanghai regional test of rape,it av-eragely yielded 2 589.75 kg/hm2 rapeseed and produced 1 273.12 kg/hm2 rapeseed oil, increasing by 14.78% over 'Huyou 15'; In the Shanghai production test of rape,it averagely yielded 3 020.85 kg/hm2 rapeseed and produced 1 485.05 kg/hm2 rapeseed oil,increasing by 21.92% over 'Huyou 15'.%‘沪油19'是通过品种(系)间复交的方法选育的高含油量甘蓝型双低油菜品种,其芥酸含量0.1%,硫苷含量18.87 μmol/g,种子含油量49.16%.在上海市油菜区域试验中,平均产量2 589.75 kg/hm2,产油量1 273.12 kg/hm2,较‘沪油15’增加14.78%;在上海市油菜生产试验中,平均产量3 020.85 kg/hm2,产油量1 485.05 kg/hm2,较‘沪油15’增加21.92%.

  7. Electrochemical Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Gang; Lin, Yuehe

    2008-07-20

    Sensitive and selective detection techniques are of crucial importance for capillary electrophoresis (CE), microfluidic chips, and other microfluidic systems. Electrochemical detectors have attracted considerable interest for microfluidic systems with features that include high sensitivity, inherent miniaturization of both the detection and control instrumentation, low cost and power demands, and high compatibility with microfabrication technology. The commonly used electrochemical detectors can be classified into three general modes: conductimetry, potentiometry, and amperometry.

  8. Accelerating yield potential in soybean: potential targets for biotechnological improvement.

    Science.gov (United States)

    Ainsworth, Elizabeth A; Yendrek, Craig R; Skoneczka, Jeffrey A; Long, Stephen P

    2012-01-01

    Soybean (Glycine max Merr.) is the world's most widely grown legume and provides an important source of protein and oil. Global soybean production and yield per hectare increased steadily over the past century with improved agronomy and development of cultivars suited to a wide range of latitudes. In order to meet the needs of a growing world population without unsustainable expansion of the land area devoted to this crop, yield must increase at a faster rate than at present. Here, the historical basis for the yield gains realized in the past 90 years are examined together with potential metabolic targets for achieving further improvements in yield potential. These targets include improving photosynthetic efficiency, optimizing delivery and utilization of carbon, more efficient nitrogen fixation and altering flower initiation and abortion. Optimization of investment in photosynthetic enzymes, bypassing photorespiratory metabolism, engineering the electron transport chain and engineering a faster recovery from the photoprotected state are different strategies to improve photosynthesis in soybean. These potential improvements in photosynthetic carbon gain will need to be matched by increased carbon and nitrogen transport to developing soybean pods and seeds in order to maximize the benefit. Better understanding of control of carbon and nitrogen transport along with improved knowledge of the regulation of flower initiation and abortion will be needed to optimize sink capacity in soybean. Although few single targets are likely to deliver a quantum leap in yields, biotechnological advances in molecular breeding techniques that allow for alteration of the soybean genome and transcriptome promise significant yield gains. © 2011 Blackwell Publishing Ltd.

  9. Quality and Yield of Cannabis Products

    DEFF Research Database (Denmark)

    Kastorp, Grith; Lindholst, Christian

    2011-01-01

    cultivation was examined in order to determine THC content and yield. The results are used by the Danish Police Attorney to estimate expected yields in cases with unripe cannabis plants. The results indicate that the THC content found in locally grown marihuana is slightly higher than in hashish. However...

  10. Central Bank Communication and the Yield Curve

    DEFF Research Database (Denmark)

    Leombroni, Matteo; Vedolin, Andrea; Venter, Gyuri

    We extract novel measures of ECB target rate announcement and communications shocks using high frequency data on money market rates and study their impact on yields of Eurozone countries. We find that (i) target rate shocks have little effect on changes in bond yields of Eurozone countries, while...

  11. Crop yield response to increasing biochar rates

    Science.gov (United States)

    The benefit or detriment to crop yield from biochar application varies with biochar type/rate, soil, crop, or climate. The objective of this research was to identify yield response of cotton (Gossypium hirsutum L.), corn (Zea mayes L.), and peanut (Arachis hypogaea L.) to hardwood biochar applied at...

  12. Yield potential of pigeon pea cultivars

    Science.gov (United States)

    Yield potential of twelve vegetable pigeon pea (Cajanus cajun) cultivars was evaluated at two locations in eastern Kenya during 2012 and 2013 cropping years. Pigeon pea pod numbers, seeds per pod, seed mass, grain yield and shelling percentage were quantified in three replicated plots, arranged in a...

  13. FEM growth and yield data monocultures - Sycamore

    NARCIS (Netherlands)

    Oldenburger, J.F.; Jansen, J.J.; Oosterbaan, A.; Mohren, G.M.J.; Ouden, den J.

    2016-01-01

    The current database is part of the FEM growth and yield database, a collection of growth and yield data from even-aged monocultures (douglas fir, common oak, poplar, Japanese Larch, Norway spruce, Scots pine, Corsican pine, Austrian pine, red oak and several other species, with only a few plots, ev

  14. Biogas and Methane Yield from Rye Grass

    Directory of Open Access Journals (Sweden)

    Tomáš Vítěz

    2015-01-01

    Full Text Available Biogas production in the Czech Republic has expanded substantially, including marginal regions for maize cultivation. Therefore, there are increasingly sought materials that could partially replace maize silage, as a basic feedstock, while secure both biogas production and its quality.Two samples of rye grass (Lolium multiflorum var. westerwoldicum silage with different solids content 21% and 15% were measured for biogas and methane yield. Rye grass silage with solid content of 15% reached an average specific biogas yield 0.431 m3·kg−1 of organic dry matter and an average specific methane yield 0.249 m3·kg−1 of organic dry matter. Rye grass silage with solid content 21% reached an average specific biogas yield 0.654 m3·kg−1 of organic dry matter and an average specific methane yield 0.399 m3·kg−1 of organic dry matter.

  15. Wheat yield dynamics: a structural econometric analysis.

    Science.gov (United States)

    Sahin, Afsin; Akdi, Yilmaz; Arslan, Fahrettin

    2007-10-15

    In this study we initially have tried to explore the wheat situation in Turkey, which has a small-open economy and in the member countries of European Union (EU). We have observed that increasing the wheat yield is fundamental to obtain comparative advantage among countries by depressing domestic prices. Also the changing structure of supporting schemes in Turkey makes it necessary to increase its wheat yield level. For this purpose, we have used available data to determine the dynamics of wheat yield by Ordinary Least Square Regression methods. In order to find out whether there is a linear relationship among these series we have checked each series whether they are integrated at the same order or not. Consequently, we have pointed out that fertilizer usage and precipitation level are substantial inputs for producing high wheat yield. Furthermore, in respect for our model, fertilizer usage affects wheat yield more than precipitation level.

  16. Precision calculations for {gamma}{gamma} {yields} 4 fermions and H {yields} WW/ZZ {yields} 4 fermions

    Energy Technology Data Exchange (ETDEWEB)

    Bredenstein, A.

    2006-05-08

    In this work we provide precision calculations for the processes {gamma}{gamma} {yields} 4 fermions and H {yields} WW/ZZ {yields} 4 fermions. At a {gamma}{gamma} collider precise theoretical predictions are needed for the {gamma}{gamma} {yields} WW {yields} 4f processes because of their large cross section. These processes allow a measurement of the gauge-boson couplings {gamma}WW and {gamma}{gamma}WW. Furthermore, the reaction {gamma}{gamma} {yields} H {yields} WW/ZZ {yields} 4f arises through loops of virtual charged, massive particles. Thus, the coupling {gamma}{gamma}H can be measured and Higgs bosons with a relatively large mass could be produced. For masses M{sub H} >or(sim) 135 GeV the Higgs boson predominantly decays into W- or Z-boson pairs and subsequently into four leptons. The kinematical reconstruction of these decays is influenced by quantum corrections, especially real photon radiation. Since off-shell effects of the gauge bosons have to be taken into account below M{sub H} {approx} 2M{sub W/Z}, the inclusion of the decays of the gauge bosons is important. In addition, the spin and the CP properties of the Higgs boson can be determined by considering angular and energy distributions of the decay fermions. For a comparison of theoretical predictions with experimental data Monte Carlo generators are useful tools. We construct such programs for the processes {gamma}{gamma} {yields} WW {yields} 4f and H {yields} WW/ZZ {yields} 4f. On the one hand, they provide the complete predictions at lowest order of perturbation theory. On the other hand, they contain quantum corrections, which ca be classified into real corrections, connected with photons bremsstrahlung, and virtual corrections. Whereas the virtual quantum corrections to {gamma}{gamma} {yields} WW {yields} 4f are calculated in the double-pole approximation, i.e. only doubly-resonant contributions are taken into account, we calculate the complete O({alpha}) corrections for the H {yields} WW

  17. The effect of yield strength and ductility to fatigue damage

    Science.gov (United States)

    Yeh, H. Y.

    1973-01-01

    The cumulative damage of aluminium alloys with different yield strength and various ductility due to seismic loads was studied. The responses of an idealized beam with a centered mass at one end and fixed at the other end to El Centro's and Taft's earthquakes are computed by assuming that the alloys are perfectly elastoplastic materials and by using numerical technique. Consequently, the corresponding residual plastic strain can be obtained from the stress-strain relationship. The revised Palmgren-Miner cumulative damage theorem is utilized to calculate the fatigue damage. The numerical results show that in certain cases, the high ductility materials are more resistant to seismic loads than the high yield strength materials. The results also show that if a structure collapse during the earthquake, the collapse always occurs in the very early stage.

  18. Densification of powder metallurgy billets by a roll consolidation technique

    Science.gov (United States)

    Sellman, W. H.; Weinberger, W. R.

    1973-01-01

    Container design is used to convert partially densified powder metallurgy compacts into fully densified slabs in one processing step. Technique improves product yield, lowers costs and yields great flexibility in process scale-up. Technique is applicable to all types of fabricable metallic materials that are produced from powder metallurgy process.

  19. Regression Models For Saffron Yields in Iran

    Science.gov (United States)

    S. H, Sanaeinejad; S. N, Hosseini

    Saffron is an important crop in social and economical aspects in Khorassan Province (Northeast of Iran). In this research wetried to evaluate trends of saffron yield in recent years and to study the relationship between saffron yield and the climate change. A regression analysis was used to predict saffron yield based on 20 years of yield data in Birjand, Ghaen and Ferdows cities.Climatologically data for the same periods was provided by database of Khorassan Climatology Center. Climatologically data includedtemperature, rainfall, relative humidity and sunshine hours for ModelI, and temperature and rainfall for Model II. The results showed the coefficients of determination for Birjand, Ferdows and Ghaen for Model I were 0.69, 0.50 and 0.81 respectively. Also coefficients of determination for the same cities for model II were 0.53, 0.50 and 0.72 respectively. Multiple regression analysisindicated that among weather variables, temperature was the key parameter for variation ofsaffron yield. It was concluded that increasing temperature at spring was the main cause of declined saffron yield during recent years across the province. Finally, yield trend was predicted for the last 5 years using time series analysis.

  20. Climate Change and Maize Yield in Iowa.

    Science.gov (United States)

    Xu, Hong; Twine, Tracy E; Girvetz, Evan

    2016-01-01

    Climate is changing across the world, including the major maize-growing state of Iowa in the USA. To maintain crop yields, farmers will need a suite of adaptation strategies, and choice of strategy will depend on how the local to regional climate is expected to change. Here we predict how maize yield might change through the 21st century as compared with late 20th century yields across Iowa, USA, a region representing ideal climate and soils for maize production that contributes substantially to the global maize economy. To account for climate model uncertainty, we drive a dynamic ecosystem model with output from six climate models and two future climate forcing scenarios. Despite a wide range in the predicted amount of warming and change to summer precipitation, all simulations predict a decrease in maize yields from late 20th century to middle and late 21st century ranging from 15% to 50%. Linear regression of all models predicts a 6% state-averaged yield decrease for every 1°C increase in warm season average air temperature. When the influence of moisture stress on crop growth is removed from the model, yield decreases either remain the same or are reduced, depending on predicted changes in warm season precipitation. Our results suggest that even if maize were to receive all the water it needed, under the strongest climate forcing scenario yields will decline by 10-20% by the end of the 21st century.

  1. Yields of rotating stars at solar metallicity

    CERN Document Server

    Hirschi, R; Maeder, A

    2004-01-01

    We present a new set of stellar yields obtained from rotating stellar models at solar metallicity covering the massive star range (12-60 solar masses). The stellar models were calculated with the latest version of the Geneva stellar evolution code described in Hirschi et al (2004). Evolution and nucleosynthesis are in general followed up to silicon burning. The yields of our non-rotating models are consistent with other calculations and differences can be understood in the light of the treatment of convection and the rate used for C12(a,g)O16. This verifies the accuracy of our calculations and gives a safe basis for studying the effects of rotation on the yields. The contributions from stellar winds and supernova explosions to the stellar yields are presented separately. We then add the two contributions to compute the total stellar yields. Below about 30 solar masses, rotation increases the total metal yields, Z, and in particular the yields of carbon and oxygen by a factor of 1.5-2.5. As a rule of thumb, th...

  2. Planting densities and Nitrogen level impact on yield and yield component of maize

    National Research Council Canada - National Science Library

    Kashif Akhtar; Muhammad Zahir Afridi; Mansoor Akbar; Sajjad Zaheer; Shah Faisal

    2015-01-01

      An experiment was conducted to find out effect of planting densities and nitrogen levels on yield and yield components of maize at Toru Mardan, Khyber Pakhtunkhwa, Pakistan, during Kharif season 2014...

  3. Correlation of yield and yield components for afila and normal leave pea, Pissum sativum L.

    Directory of Open Access Journals (Sweden)

    Đorđević Radiša

    2004-01-01

    Full Text Available In order to research the correlation of yield and yield components of Afila and normal leaf Pea, we conducted a three years research (1993 - 1995. We have researched a correlative junction of yield and yield components (number of pods, number of grains per pod, number of grains per plant and the absolute grain weight of 8 Afila lines and 4 parent varieties. The results showed that the yield and yield components are highly related r - 0.82 - 0.95, while the absolute weight is not related to the yield r - 0, 19 and due to that it does not represent the yield component. The determined correlative values for all researched genotypes and parents were the same as previously researched by other authors, which leads us to the conclusion that the absence of leaves does not directly impact the change of correlative values.

  4. Combinatorial techniques

    CERN Document Server

    Sane, Sharad S

    2013-01-01

    This is a basic text on combinatorics that deals with all the three aspects of the discipline: tricks, techniques and theory, and attempts to blend them. The book has several distinctive features. Probability and random variables with their interconnections to permutations are discussed. The theme of parity has been specially included and it covers applications ranging from solving the Nim game to the quadratic reciprocity law. Chapters related to geometry include triangulations and Sperner's theorem, classification of regular polytopes, tilings and an introduction to the Eulcidean Ramsey theory. Material on group actions covers Sylow theory, automorphism groups and a classification of finite subgroups of orthogonal groups. All chapters have a large number of exercises with varying degrees of difficulty, ranging from material suitable for Mathematical Olympiads to research.

  5. 优质高产中早熟玉米新品种冀玉5817的选育及其栽培技术要点%Breeding and Cultivation Techniques of New Maize Variety Jiyu 5817 with High Quality and Yield and Mid-early Maturing

    Institute of Scientific and Technical Information of China (English)

    王江浩; 缴瑞华; 尤帅; 赵爱菊; 于翠红; 高增玉

    2015-01-01

    冀玉5817是河北省农林科学院粮油作物研究所以自交系郑58-3为母本、自交系B37为父本杂交选育而成的玉米新品种。该品种丰产性和稳产性好,熟期较早;抗病性强,中抗小斑病、茎腐病和弯孢叶斑病,高抗大斑病;籽粒品质优良,达到国家饲用玉米2级标准;适宜在河北省唐山、廊坊、保定北部和沧州北部的夏播玉米区种植。2014年通过河北省农作物品种审定委员会品种审定(审定编号:冀审玉2014017号)。%New maize hybrid Jiyu 5817 was bred with inbredline Zheng58-3 as female parent and inbred-line B37 as male parent by Institute of Cereal and Oil Crops,Hebei Academy of Agriculture and Forestry Sciences.It with high and stable yield, earlier maturity, resistance to corn southern leaf blight and stem rot and bending cell leaf spot disease, strong resistance to corn northern leaf blight.Its grain quality is excellent,which reached the national forage corn secondary standard. It is suitable for sowing in summer sown areas of Tangshan,Cangzhou,Langfang,Baoding and Northern Hebei Province. It was approved by Hebei Crop Variety Approval Committee in 2014,the approval number was Jishenyu NO. 2014017.

  6. Optimizing rice yields while minimizing yield-scaled global warming potential.

    Science.gov (United States)

    Pittelkow, Cameron M; Adviento-Borbe, Maria A; van Kessel, Chris; Hill, James E; Linquist, Bruce A

    2014-05-01

    To meet growing global food demand with limited land and reduced environmental impact, agricultural greenhouse gas (GHG) emissions are increasingly evaluated with respect to crop productivity, i.e., on a yield-scaled as opposed to area basis. Here, we compiled available field data on CH4 and N2 O emissions from rice production systems to test the hypothesis that in response to fertilizer nitrogen (N) addition, yield-scaled global warming potential (GWP) will be minimized at N rates that maximize yields. Within each study, yield N surplus was calculated to estimate deficit or excess N application rates with respect to the optimal N rate (defined as the N rate at which maximum yield was achieved). Relationships between yield N surplus and GHG emissions were assessed using linear and nonlinear mixed-effects models. Results indicate that yields increased in response to increasing N surplus when moving from deficit to optimal N rates. At N rates contributing to a yield N surplus, N2 O and yield-scaled N2 O emissions increased exponentially. In contrast, CH4 emissions were not impacted by N inputs. Accordingly, yield-scaled CH4 emissions decreased with N addition. Overall, yield-scaled GWP was minimized at optimal N rates, decreasing by 21% compared to treatments without N addition. These results are unique compared to aerobic cropping systems in which N2 O emissions are the primary contributor to GWP, meaning yield-scaled GWP may not necessarily decrease for aerobic crops when yields are optimized by N fertilizer addition. Balancing gains in agricultural productivity with climate change concerns, this work supports the concept that high rice yields can be achieved with minimal yield-scaled GWP through optimal N application rates. Moreover, additional improvements in N use efficiency may further reduce yield-scaled GWP, thereby strengthening the economic and environmental sustainability of rice systems.

  7. Maximizing oil yields may not optimize economics

    Energy Technology Data Exchange (ETDEWEB)

    1987-03-01

    The Los Alamos National Laboratory has used the ASPEN computer code to calculate the economics of different hydroretorting conditions. When the oil yield was maximized and a oil shale plant designed around this process, the costs turned out much higher than expected. However, calculations based on runs of less than maximum yields showed lower cost estimates. It is recommended that future efforts should be concentrated on minimizing production costs rather than maximizing yields. An oil shale plant has been designed around minimum production cost, but has not been able to be tested experimentally.

  8. Optimizing Diagnostic Yield for EUS-Guided Sampling of Solid Pancreatic Lesions: A Technical Review

    Science.gov (United States)

    Weston, Brian R.

    2013-01-01

    Endoscopic ultrasound-guided fine-needle aspiration (EUS-FNA) has a higher diagnostic accuracy for pancreatic cancer than other techniques. This article will review the current advances and considerations for optimizing diagnostic yield for EUS-guided sampling of solid pancreatic lesions. Preprocedural considerations include patient history, confirmation of appropriate indication, review of imaging, method of sedation, experience required by the endoscopist, and access to rapid on-site cytologic evaluation. New EUS imaging techniques that may assist with differential diagnoses include contrast-enhanced harmonic EUS, EUS elastography, and EUS spectrum analysis. FNA techniques vary, and multiple FNA needles are now commercially available; however, neither techniques nor available FNA needles have been definitively compared. The need for suction depends on the lesion, and the need for a stylet is equivocal. No definitive endosonographic finding can predict the optimal number of passes for diagnostic yield. Preparation of good smears and communication with the cytopathologist are essential to optimize yield. PMID:23935542

  9. Rice yields and yield gaps in Southeast Asia: Past trends and future outlook

    NARCIS (Netherlands)

    Laborte, A.G.; Bie, de C.A.J.M.; Smaling, E.M.A.; Moya, P.F.; Boling, A.A.; Ittersum, van M.K.

    2012-01-01

    Rice production must increase to meet future food requirements amid strong competition for limited resources. Yield gap analysis is a useful method to examine how large the ranges are between potential, desirable rice yields and those actually realized in farmers’ fields. We analyzed farmers’ yields

  10. Remotely sensed rice yield prediction using multi-temporal NDVI data derived from NOAA's-AVHRR.

    Science.gov (United States)

    Huang, Jingfeng; Wang, Xiuzhen; Li, Xinxing; Tian, Hanqin; Pan, Zhuokun

    2013-01-01

    Grain-yield prediction using remotely sensed data have been intensively studied in wheat and maize, but such information is limited in rice, barley, oats and soybeans. The present study proposes a new framework for rice-yield prediction, which eliminates the influence of the technology development, fertilizer application, and management improvement and can be used for the development and implementation of provincial rice-yield predictions. The technique requires the collection of remotely sensed data over an adequate time frame and a corresponding record of the region's crop yields. Longer normalized-difference-vegetation-index (NDVI) time series are preferable to shorter ones for the purposes of rice-yield prediction because the well-contrasted seasons in a longer time series provide the opportunity to build regression models with a wide application range. A regression analysis of the yield versus the year indicated an annual gain in the rice yield of 50 to 128 kg ha(-1). Stepwise regression models for the remotely sensed rice-yield predictions have been developed for five typical rice-growing provinces in China. The prediction models for the remotely sensed rice yield indicated that the influences of the NDVIs on the rice yield were always positive. The association between the predicted and observed rice yields was highly significant without obvious outliers from 1982 to 2004. Independent validation found that the overall relative error is approximately 5.82%, and a majority of the relative errors were less than 5% in 2005 and 2006, depending on the study area. The proposed models can be used in an operational context to predict rice yields at the provincial level in China. The methodologies described in the present paper can be applied to any crop for which a sufficient time series of NDVI data and the corresponding historical yield information are available, as long as the historical yield increases significantly.

  11. Estimating Sugarcane Yield Potential Using an In-Season Determination of Normalized Difference Vegetative Index

    Directory of Open Access Journals (Sweden)

    Howard Viator

    2012-06-01

    Full Text Available Estimating crop yield using remote sensing techniques has proven to be successful. However, sugarcane possesses unique characteristics; such as, a multi-year cropping cycle and plant height-limiting for midseason fertilizer application timing. Our study objective was to determine if sugarcane yield potential could be estimated using an in-season estimation of normalized difference vegetative index (NDVI. Sensor readings were taken using the GreenSeeker® handheld sensor from 2008 to 2011 in St. Gabriel and Jeanerette, LA, USA. In-season estimates of yield (INSEY values were calculated by dividing NDVI by thermal variables. Optimum timing for estimating sugarcane yield was between 601–750 GDD. In-season estimated yield values improved the yield potential (YP model compared to using NDVI. Generally, INSEY value showed a positive exponential relationship with yield (r2 values 0.48 and 0.42 for cane tonnage and sugar yield, respectively. When models were separated based on canopy structure there was an increase the strength of the relationship for the erectophile varieties (r2 0.53 and 0.47 for cane tonnage and sugar yield, respectively; however, the model for planophile varieties weakened slightly. Results of this study indicate using an INSEY value for predicting sugarcane yield shows potential of being a valuable management tool for sugarcane producers in Louisiana.

  12. Estimating sugarcane yield potential using an in-season determination of normalized difference vegetative index.

    Science.gov (United States)

    Lofton, Josh; Tubana, Brenda S; Kanke, Yumiko; Teboh, Jasper; Viator, Howard; Dalen, Marilyn

    2012-01-01

    Estimating crop yield using remote sensing techniques has proven to be successful. However, sugarcane possesses unique characteristics; such as, a multi-year cropping cycle and plant height-limiting for midseason fertilizer application timing. Our study objective was to determine if sugarcane yield potential could be estimated using an in-season estimation of normalized difference vegetative index (NDVI). Sensor readings were taken using the GreenSeeker® handheld sensor from 2008 to 2011 in St. Gabriel and Jeanerette, LA, USA. In-season estimates of yield (INSEY) values were calculated by dividing NDVI by thermal variables. Optimum timing for estimating sugarcane yield was between 601-750 GDD. In-season estimated yield values improved the yield potential (YP) model compared to using NDVI. Generally, INSEY value showed a positive exponential relationship with yield (r(2) values 0.48 and 0.42 for cane tonnage and sugar yield, respectively). When models were separated based on canopy structure there was an increase the strength of the relationship for the erectophile varieties (r(2) 0.53 and 0.47 for cane tonnage and sugar yield, respectively); however, the model for planophile varieties weakened slightly. Results of this study indicate using an INSEY value for predicting sugarcane yield shows potential of being a valuable management tool for sugarcane producers in Louisiana.

  13. Using NDVI and guided sampling to develop yield prediction maps of processing tomato crop

    Energy Technology Data Exchange (ETDEWEB)

    Fortes, A.; Henar Prieto, M. del; García-Martín, A.; Córdoba, A.; Martínez, L.; Campillo, C.

    2015-07-01

    The use of yield prediction maps is an important tool for the delineation of within-field management zones. Vegetation indices based on crop reflectance are of potential use in the attainment of this objective. There are different types of vegetation indices based on crop reflectance, the most commonly used of which is the NDVI (normalized difference vegetation index). NDVI values are reported to have good correlation with several vegetation parameters including the ability to predict yield. The field research was conducted in two commercial farms of processing tomato crop, Cantillana and Enviciados. An NDVI prediction map developed through ordinary kriging technique was used for guided sampling of processing tomato yield. Yield was studied and related with NDVI, and finally a prediction map of crop yield for the entire plot was generated using two geostatistical methodologies (ordinary and regression kriging). Finally, a comparison was made between the yield obtained at validation points and the yield values according to the prediction maps. The most precise yield maps were obtained with the regression kriging methodology with RRMSE values of 14% and 17% in Cantillana and Enviciados, respectively, using the NDVI as predictor. The coefficient of correlation between NDVI and yield was correlated in the point samples taken in the two locations, with values of 0.71 and 0.67 in Cantillana and Enviciados, respectively. The results suggest that the use of a massive sampling parameter such as NDVI is a good indicator of the distribution of within-field yield variation. (Author)

  14. Effects of techniques of paddy field production mechanization on occurrence of diseases, insect pests, weeds and yield of double-cropping rice%全程机械化生产对双季稻病虫草发生及产量的影响

    Institute of Scientific and Technical Information of China (English)

    李保同; 张建中; 吴建富; 潘晓华; 石庆华

    2013-01-01

    7.88%。该研究为双季稻区水稻全程机械化生产病虫草防治技术的推广提供参考。%Four patterns such as mechanized rotary tillage-mechanized transplanting method, mechanized rotary with cattle tillage-mechanized transplanting method, cattle tillage-mechanized transplanting method and mechanized rotary tillage-manual transplanting method were tested in order to investigate the effects of different plowing-transplanting methods on diseases, insect pests, weeds and yield of double-cropping rice. Results showed that major diseases, insect pests and weeds were sheath blight disease Rhizoctonia solani, Cnaphalocrocis medinalis, Monochoria vaginalis and Echinochloa crusgalli in early rice with four plowing-transplanting methods in no using pesticide areas, and sheath blight disease, C medinalis, rice planthopper (Sogatella furcifera and Nilaparvata lugens), M. vaginalis and E. crusgalli in late rice. Under the same conditions of fertilizer and water management, the sheath blight disease indexes of early and late rice were 8.25-13.31 and 17.60-23.10 at booting stage, 13.75-20.90 and 20.02-23.76 at milky stage, respectively, which was more serious using mechanized rotary tillage-manual transplanting method than that using mechanized rotary tillage-mechanized transplanting method, and more serious using cattle tillage-mechanized transplanting method than that using mechanized rotary tillage-mechanized transplanting method. The second generation of C. medinalis occurred seriously in early rice, and its curled leaf rates were 15.03%-16.67%. The fourth and fifth generation of C. medinalis in late rice occurred seriously, and its curled leaf rates were 29.67%-33.48% and 60.09%-65.45%, respectively. The occurrence difference of C. medinalis was not significant between four plowing-transplanting methods in early and late rice. The population density of rice planthoppers in late rice was low at early stage, 425-550 heads/100 clusters at full heading stage

  15. Soybean Yield Determinants and Response to Rhizobial ...

    African Journals Online (AJOL)

    parameters (shoot, root, nodule number and shoot and nodule fresh weight) measured. ... the BNF and grain yield of the improved variety were significantly higher than the ..... On the whole, field ... nutrient loss especially N through leaching.

  16. Multiple frequency atmospheric radar techniques

    Science.gov (United States)

    Stitt, Gary Richard

    The use of multiple frequency coding to improve the vertical resolution of pulsed-Doppler very high frequency atmospheric radars, especially with regards to the two-frequency techniques known as frequency domain interferometry (FDI), is presented. This technique consists of transmitting alternate pulses on two distinct carrier frequencies. The two resulting time series are used to evaluate the normalized cross-correlation function, whose magnitude and phase are related to the thickness and position of a scattering layer. These same time series are also used to evaluate cross-spectra, which yield magnitude and phase values for each Doppler frequency component of the return signal.

  17. Soft photon yield in nuclear interactions

    CERN Document Server

    Kokoulina, E

    2015-01-01

    First results of study of a soft photon yield at Nuclotron (LHEP, JINR) in nucleus-nucleus collisions at 3.5 GeV per nucleon are presented. These photons are registered by an BGO electromagnetic calorimeter built by SVD-2 Collaboration. The obtained spectra confirm the excessive yield in the energy region less than 50 MeV in comparison with theoretical estimations and agree with previous experiments at high-energy interactions.

  18. Soft photon yield in nuclear interactions

    Science.gov (United States)

    Kokoulina, E.

    2016-01-01

    First results of the study of a soft photon yield in nucleus-nucleus collisions at 3.5 GeV per nucleon at Nuclotron (LHEP, JINR) are presented. These photons are registered by an BGO electromagnetic calorimeter built by the SVD-2 Collaboration. The obtained spectra confirm the excessive yield in the energy region less than 50 MeV in comparison with theoretical estimations and agree with previous experiments at high-energy interactions.

  19. Soft photon yield in nuclear interactions

    Directory of Open Access Journals (Sweden)

    Kokoulina E.

    2016-01-01

    Full Text Available First results of the study of a soft photon yield in nucleus-nucleus collisions at 3.5 GeV per nucleon at Nuclotron (LHEP, JINR are presented. These photons are registered by an BGO electromagnetic calorimeter built by the SVD-2 Collaboration. The obtained spectra confirm the excessive yield in the energy region less than 50 MeV in comparison with theoretical estimations and agree with previous experiments at high-energy interactions.

  20. N-acetylcysteine increased rice yield

    OpenAIRE

    NOZULAIDI, MOHD; JAHAN, MD SARWAR; KHAIRI, MOHD; Khandaker, Mohammad Moneruzzaman; Mat NASHRIYAH; KHANIF, YUSOP MOHD

    2015-01-01

    N-acetylcysteine (NAC) biosynthesized reduced glutathione (GSH), which maintains redox homeostasis in plants under normal and stressful conditions. To justify the effects of NAC on rice production, we measured yield parameters, chlorophyll (Chl) content, minimum Chl fluorescence (Fo), maximum Chl fluorescence (Fm), quantum yield (Fv/Fm), net photosynthesis rate (Pn), photosynthetically active radiation (PAR), and relative water content (RWC). Four treatments, N1G0 (nitrogen (N) with no NAC), ...

  1. Computerized tomography technique for reconstruction of obstructed temperature field in infrared thermography

    Science.gov (United States)

    Sham, F. C.; Huang, Y. H.; Liu, L.; Chen, Y. S.; Hung, Y. Y.; Lo, T. Y.

    2010-01-01

    Infrared thermography is a rapid, non-invasive and full-field technique for non-destructive testing and evaluation (NDT&E). With all the achievements on IR instrumentation and image processing techniques attained, it has been extended far beyond simple hot-spot detection and becomes one of the most promising NDT&E techniques in the last decades. It has achieved increasing acceptance in different sectors include medical imaging, manufacturing component fault detection and buildings diagnostic. However, one limitation of IR thermography is that the testing results are greatly affected by object surface emissivity. Surface with various emissivities may lead to difficult discrimination between area of defect and area with different emissivity. Therefore, many studies have been carried out on eliminating emissivity, for example, the time derivative approach, lock-in processing and differential contrast measurements. In these methods, sequence of themo-data/images are recorded and being processed in order to eliminate differences of emissivity. Another problem of IR thermography is that any obstruction may limit stimulations and imaging which leads to the observation of unclear defect image. To solve this problem, this paper proposes an algorithm based on the principle of computerized tomography which permits the reconstruction of unavailable/partially available temperature distribution of the affected area using the measured surrounding temperature field. In the process, a set of imaginary rays are projected from many different directions across the area. For each ray, integration of the temperature derivatives along the ray is equals to the temperature difference between the boundary points intercepted by the ray. Therefore, a set of linear equations can be established by considering the multiple rays. Each equation expresses the unknown temperature derivatives in the affected area in terms of the measured boundary temperature data. Solution of the set of simultaneous

  2. Experimental Techniques

    DEFF Research Database (Denmark)

    Wyer, Jean

    2013-01-01

    Gas-phase ion spectroscopy requires specialised apparatus, both when it comes to measuring photon absorption and light emission (fluorescence). The reason is much lower ion densities compared to solution-phase spectroscopy. In this chapter different setups are described, all based on mass spectro...... in data interpretation, and the advantages and disadvantages of the different techniques are clarified. New instrumental developments involving cryo-cooled storage rings, which show great promise for the future, are briefly touched upon.......Gas-phase ion spectroscopy requires specialised apparatus, both when it comes to measuring photon absorption and light emission (fluorescence). The reason is much lower ion densities compared to solution-phase spectroscopy. In this chapter different setups are described, all based on mass...... to circumvent this is discussed based on a chemical approach, namely tagging of ammonium groups by crown ether. Prompt dissociation can sometimes be identified from the total beam depletion differing from that due to statistical dissociation. Special emphasis in this chapter is on the limitations and pitfalls...

  3. Yield criteria for quasibrittle and frictional materials

    CERN Document Server

    Bigoni, Davide

    2010-01-01

    A new yield/damage function is proposed for modelling the inelastic behaviour of a broad class of pressure-sensitive, frictional, ductile and brittle-cohesive materials. The yield function allows the possibility of describing a transition between the shape of a yield surface typical of a class of materials to that typical of another class of materals. This is a fundamental key to model the behaviour of materials which become cohesive during hardening (so that the shape of the yield surface evolves from that typical of a granular material to that typical of a dense material), or which decrease cohesion due to damage accumulation. The proposed yield function is shown to agree with a variety of experimental data relative to soil, concrete, rock, metallic and composite powders, metallic foams, porous metals, and polymers. The yield function represents a single, convex and smooth surface in stress space approaching as limit situations well-known criteria and the extreme limits of convexity in the deviatoric plane....

  4. Modulus and yield stress of drawn LDPE

    Science.gov (United States)

    Thavarungkul, Nandh

    Modulus and yield stress were investigated in drawn low density polyethylene (LDPE) film. Uniaxially drawn polymeric films usually show high values of modulus and yield stress, however, studies have normally only been conducted to identify the structural features that determine modulus. In this study small-angle x-ray scattering (SAXS), thermal shrinkage, birefringence, differential scanning calorimetry (DSC), and dynamic mechanical thermal analysis (DMTA) were used to examine, directly and indirectly, the structural features that determine both modulus and yield stress, which are often closely related in undrawn materials. Shish-kebab structures are proposed to account for the mechanical properties in drawn LDPE. The validity of this molecular/morphological model was tested using relationships between static mechanical data and structural and physical parameters. In addition, dynamic mechanical results are also in line with static data in supporting the model. In the machine direction (MD), "shish" and taut tie molecules (TTM) anchored in the crystalline phase account for E; whereas crystal lamellae with contributions from "shish" and TTM determine yield stress. In the transverse direction (TD), the crystalline phase plays an important roll in both modulus and yield stress. Modulus is determined by crystal lamellae functioning as platelet reinforcing elements in the amorphous matrix with an additional contributions from TTM and yield stress is determined by the crystal lamellae's resistance to deformation.

  5. Water limits to closing yield gaps

    Science.gov (United States)

    Davis, Kyle Frankel; Rulli, Maria Cristina; Garrassino, Francesco; Chiarelli, Davide; Seveso, Antonio; D'Odorico, Paolo

    2017-01-01

    Agricultural intensification is often seen as a suitable approach to meet the growing demand for agricultural products and improve food security. It typically entails the use of fertilizers, new cultivars, irrigation, and other modern technology. In regions of the world affected by seasonal or chronic water scarcity, yield gap closure is strongly dependent on irrigation (blue water). Global yield gap assessments have often ignored whether the water required to close the yield gap is locally available. Here we perform a gridded global analysis (10 km resolution) of the blue water consumption that is needed annually to close the yield gap worldwide and evaluate the associated pressure on renewable freshwater resources. We find that, to close the yield gap, human appropriation of freshwater resources for irrigation would have to increase at least by 146%. Most study countries would experience at least a doubling in blue water requirement, with 71% of the additional blue water being required by only four crops - maize, rice, soybeans, and wheat. Further, in some countries (e.g., Algeria, Morocco, Syria, Tunisia, and Yemen) the total volume of blue water required for yield gap closure would exceed sustainable levels of freshwater consumption (i.e., 40% of total renewable surface and groundwater resources).

  6. 水稻覆膜节水综合高产技术对稻田CH4排放的影响%Effect of high-yield rice planting technique integrated with plastic mulching for water saving on methane emission from rice fields

    Institute of Scientific and Technical Information of China (English)

    张怡; 吕世华; 马静; 徐华; 袁江; 董瑜皎

    2013-01-01

      采用静态箱-气相色谱法观测了常规栽培和水稻覆膜节水综合高产技术下川中丘陵地区稻田的CH4排放通量,探究覆膜节水综合高产技术对稻田CH4排放的影响。结果表明:整个水稻生长期,常规栽培与水稻覆膜节水综合高产技术稻田CH4排放总量分别为(35.0±3.5)和(5.1±1.0) g·m-2,后者较前者减少稻田CH4季节排放量的(86±4)%。二者CH4平均排放通量在不同水稻生长时期存在如下关系:孕穗期>抽穗期>成熟期>分蘖期。水稻各生长时期,覆膜节水综合高产技术均降低稻田CH4排放,在稻田CH4排放盛期(孕穗期)降幅达79%。在不同土壤水分状况下,水稻覆膜节水综合高产技术稻田CH4平均排放通量存在如下关系:烤田期>烤田后>烤田前;而常规栽培则为烤田期>烤田前>烤田后。不同于常规栽培,烤田对水稻覆膜节水综合高产技术下稻田 CH4排放无明显影响,烤田后降雨促进其 CH4排放。土壤水分状况由低变高更易促使覆膜节水综合高产技术下稻田CH4排放。覆膜节水综合高产技术栽培全生育期内,厢面CH4排放通量与土温、土壤Eh无显著相关性(P>0.05)。厢沟CH4排放与土温显著正相关(r=0.447*,P heading stage >maturing stage>tillering stage. The new technique decreased CH4 emission at all the rice growth stages, especially at the earring stage, and when CH4 emission was the highest, it did by as much as 79%. The effect of the new technique also varied with the soil water regime and the mean CH4 emission displayed an order of mid-season aeration > post-aeration > pre-aeration, while in the conventional field, it followed the order of mid-season aeration > pre-aeration > post-aeration. Different from the situation in the conventional field, the mid-season aeration did not have much effect on CH4 emission in the field using the new planting technique. In that field, rainfall after the

  7. Overlapped flowers yield detection using computer-based interface

    Directory of Open Access Journals (Sweden)

    Anuradha Sharma

    2016-09-01

    Full Text Available Precision agriculture has always dealt with the accuracy and timely information about agricultural products. With the help of computer hardware and software technology designing a decision support system that could generate flower yield information and serve as base for management and planning of flower marketing is made so easy. Despite such technologies, some problem still arise, for example, a colour homogeneity of a specimen which cannot be obtained similar to actual colour of image and overlapping of image. In this paper implementing a new ‘counting algorithm’ for overlapped flower is being discussed. For implementing this algorithm, some techniques and operations such as colour image segmentation technique, image segmentation, using HSV colour space and morphological operations have been used. In this paper used two most popular colour space; those are RGB and HSV. HSV colour space decouples brightness from a chromatic component in the image, by which it provides better result in case for occlusion and overlapping.

  8. Free ion yields for nonpolar liquids exposed to 1.6-3.5 keV X-rays

    CERN Document Server

    Holroyd, R A

    1998-01-01

    The yields of free ions formed following absorption of 1.6-3.5 keV X-rays were determined for several nonpolar liquids using a conductivity technique. The yields are much less for X-rays than for gamma rays; this effect is largest for branched hydrocarbons. A minimum in yield is observed around 2 keV. The dependence of G sub f sub i sup o on X-ray energy is in good agreement with computer simulations. For tetramethylsilane a sharp dip in ion yield is observed at the Si ls -> sigma sup * resonance, indicating that the free electron yield is even less at this energy.

  9. Role of Yield Stress in Magma Rheology

    Science.gov (United States)

    Kurokawa, A.; Di Giuseppe, E.; Davaille, A.; Kurita, K.

    2012-04-01

    Magmas are essentially multiphase material composed of solid crystals, gaseous bubbles and silicate liquids. They exhibit various types of drastic change in rheology with variation of mutual volumetric fractions of the components. The nature of this variable rheology is a key factor in controlling dynamics of flowing magma through a conduit. Particularly the existence of yield stress in flowing magma is expected to control the wall friction and formation of density waves. As the volumetric fraction of solid phase increases yield stress emerges above the critical fraction. Several previous studies have been conducted to clarify this critical value of magmatic fluid both in numerical simulations and laboratory experiments ([Lejeune and Pascal, 1995], [Saar and Manga 2001], [Ishibashi and Sato 2010]). The obtained values range from 13.3 to 40 vol%, which display wide variation and associated change in rheology has not been clarified well. In this presentation we report physical mechanism of emergence of yield stress in suspension as well as the associated change in the rheology based on laboratory experiments using analog material. We utilized thermogel aqueous suspension as an analog material of multiphase magma. Thermogel, which is a commercial name for poly(N-isopropyl acrylamide) (PNIPAM) undergoes volumetric phase change at the temperature around 35C:below this temperature the gel phase absorbs water and swells while below this it expels water and its volume shrinks. Because of this the volumetric fraction of gel phase systematically changes with temperature and the concentration of gel powder. The viscosity measured at lower stress drastically decreases across this phase change with increasing temperature while the viscosity at higher stress does not exhibit large change across the transition. We have performed a series of rheological measurements focusing on the emergence of yield stress on this aqueous suspension. Since the definition of yield stress is not

  10. 157例乳腺浸润性导管癌全数字化X线征象分析%The analyses of X-ray signs of 157 cases of breast infiltrating ductal carcinoma with full-field digital mammography

    Institute of Scientific and Technical Information of China (English)

    陈玉兰; 董江宁; 王婷婷; 吴瑶媛

    2016-01-01

    Objective To analyze the signs of full-field digital mammography ( FFDM) in breast infiltrating ductal carcinoma ( IDC) and to raise the diagnostic accuracy .Methods For 157 cases with surgically and pathologically proved breast infiltrating ductal carcinoma, IDC signs of full-field digital mammography were analyzed retrospectively .Craniocandal (CC) view and medio-lateral oblique (MLO) view were conducted for each patient .Besides, tangential view, exaggerated craniocaudal view , cleavage view, 90°lateral view or spot compression view were examined if necessary .5 cases were facilitated with breast MRI .Results 157 cases of direct signs of IDC included mass with dandruff , amorphous, or vermicular microcalcification in 90 cases (57%), mass only in 44 cases (28%), architecture distortion or focal asymmetric density in 18 cases (11%), 4 cases with microcalcifi-cation, microcalcification only in 5 cases (3%).154 cases of IDC with indirect signs (154/157, 98%) inclued blood circulation increased (52/157), enlargement of the catheter (45/157), areola and skin thickening (41/157), nipple retraction (39/157), breast or axillary lymph nodes enlargement (70/157).Conclusion Lobulated and/or burr shape breast mass, dandruff form, a-morphous, vermicular and branch microcalcification are the main signs of IDC .For untypical X-ray signs of IDC, careful observa-tion of indirect signs in professional workstation is needed to integrate analysis , IDC preoperative diagnostic accuracy can be effec-tively improved .%目的:探讨乳腺浸润性导管癌( IDC)全数字化X线征象,提高诊断准确率。方法收集术前行数字化乳腺X线摄影检查且术后经病理证实为乳腺浸润性导管癌患者157例,回顾性分析IDC全数字化X线表现特征。每位患者摄取乳腺头尾位和内外侧斜位(CC位和MLO位),部分加拍切线位、扩大头尾位、乳沟位、90°侧位及点片压迫位。5例加做乳腺MRI。结果157例IDC的直接征

  11. Field Measurements of Black Carbon Yields from Gas Flaring.

    Science.gov (United States)

    Conrad, Bradley M; Johnson, Matthew R

    2017-02-07

    Black carbon (BC) emissions from gas flaring in the oil and gas industry are postulated to have critical impacts on climate and public health, but actual emission rates remain poorly characterized. This paper presents in situ field measurements of BC emission rates and flare gas volume-specific BC yields for a diverse range of flares. Measurements were performed during a series of field campaigns in Mexico and Ecuador using the sky-LOSA optical measurement technique, in concert with comprehensive Monte Carlo-based uncertainty analyses. Parallel on-site measurements of flare gas flow rate and composition were successfully performed at a subset of locations enabling direct measurements of fuel-specific BC yields from flares under field conditions. Quantified BC emission rates from individual flares spanned more than 4 orders of magnitude (up to 53.7 g/s). In addition, emissions during one notable ∼24-h flaring event (during which the plume transmissivity dropped to zero) would have been even larger than this maximum rate, which was measured as this event was ending. This highlights the likely importance of superemitters to global emission inventories. Flare gas volume-specific BC yields were shown to be strongly correlated with flare gas heating value. A newly derived correlation fitting current field data and previous lab data suggests that, in the context of recent studies investigating transport of flare-generated BC in the Arctic and globally, impacts of flaring in the energy industry may in fact be underestimated.

  12. Measurement of Fission Product Yields from Fast-Neutron Fission

    Science.gov (United States)

    Arnold, C. W.; Bond, E. M.; Bredeweg, T. A.; Fowler, M. M.; Moody, W. A.; Rusev, G.; Vieira, D. J.; Wilhelmy, J. B.; Becker, J. A.; Henderson, R.; Kenneally, J.; Macri, R.; McNabb, D.; Ryan, C.; Sheets, S.; Stoyer, M. A.; Tonchev, A. P.; Bhatia, C.; Bhike, M.; Fallin, B.; Gooden, M. E.; Howell, C. R.; Kelley, J. H.; Tornow, W.

    2014-09-01

    One of the aims of the Stockpile Stewardship Program is a reduction of the uncertainties on fission data used for analyzing nuclear test data [1,2]. Fission products such as 147Nd are convenient for determining fission yields because of their relatively high yield per fission (about 2%) and long half-life (10.98 days). A scientific program for measuring fission product yields from 235U,238U and 239Pu targets as a function of bombarding neutron energy (0.1 to 15 MeV) is currently underway using monoenergetic neutron beams produced at the 10 MV Tandem Accelerator at TUNL. Dual-fission chambers are used to determine the rate of fission in targets during activation. Activated targets are counted in highly shielded HPGe detectors over a period of several weeks to identify decaying fission products. To date, data have been collected at neutron bombarding energies 4.6, 9.0, 14.5 and 14.8 MeV. Experimental methods and data reduction techniques are discussed, and some preliminary results are presented.

  13. A novel method for the absolute fluorescence yield measurement by AIRFLY

    CERN Document Server

    Ave, M

    2008-01-01

    One of the goals of the AIRFLY (AIR FLuorescence Yield) experiment is to measure the absolute fluorescence yield induced by electrons in air to better than 10% precision. We introduce a new technique for measurement of the absolute fluorescence yield of the 337 nm line that has the advantage of reducing the systematic uncertainty due to the detector calibration. The principle is to compare the measured fluorescence yield to a well known process - the Cerenkov emission. Preliminary measurements taken in the BFT (Beam Test Facility) in Frascati, Italy with 350 MeV electrons are presented. Beam tests in the Argonne Wakefield Accelerator at the Argonne National Laboratory, USA with 14 MeV electrons have also shown that this technique can be applied at lower energies.

  14. Defect reduction methodologies: pellicle yield improvement

    Science.gov (United States)

    Daugherty, Susan V.

    1993-03-01

    The pelliclization process at Intel during the first half of 1991 was not in control. Weekly process yield was trending downward, and the range of the weekly yield during that time frame was greater than 40%. A focused effort in process yield improvement, that started in the second half of 1991 and continued through 1992, brought process yield up an average of 20%, and reduced the range of the process yield to 20 - 25%. This paper discusses the continuous process improvement guidelines that are being followed to reduce variations/defects in the pelliclization process. Teamwork tools, such as Pareto charts, fishbone diagrams, and simple experiments, prioritize efforts and help find the root cause of the defects. Best known methods (BKM), monitors, PMs, and excursion control aid in the elimination and prevention of defects. Monitoring progress and repeating the whole procedure are the final two guidelines. The benefits from the use of the continuous process improvement guidelines and tools can be seen in examples of the actions, impacts, and results for the last half of 1991 and the first half of 1992.

  15. Particle debonding using different yield criteria

    DEFF Research Database (Denmark)

    Legarth, Brian Nyvang; Kuroda, Mitsutoshi

    2004-01-01

    is subjected to a fixed biaxial stress state. Four phenomenological anisotropic yield criteria are considered, namely Hill [Hill, R., 1948. Proc. Roy. Soc. London Ser. A 193, 281-297], Barlat and Lian [Barlat, F., Lian, J., 1989. Int. J. Plasticity 5, 51-66], Barlat et al. [Barlat, F., Lege, D.J., Brem, J.......C., 1991. Int. J. Plasticity 7, 693-712; Barlat, F., et al., 2003. Int. J. Plasticity 19, 1297-1319], or the von Mises isotropic yield surface. Also a non-normality flow rule is adopted in some of the studies. Significant effects of plastic anisotropy are seen on the plane stress cell, due to the initial...... extent and shape of the particular yield function considered. The required overall straining of the cell for debonding initiation is related to the extent of the yield surfaces, since a high yield stress promotes debonding. Additionally, the maximum overall stress level for the cell is lower for the Hill...

  16. An assessment of fine-needle sampling techniques.

    Science.gov (United States)

    Titoria, Puneet; Siva, Thiru M; Malik, Tass

    2010-07-01

    Fine-needle cytology sampling, when adequate, is highly sensitive and specific for tissue-type diagnosis, with figures of 94% and 88%, respectively. This study explores the technique of sampling to reduce interoperator variability and ensure maximal tissue yield. Apple cortical tissue was sampled as a proxy of human lymph node. A total of 200 samples, by four methods, with 50 by each sampling method, were taken using blue venepuncture needles and weighed to assess tissue yield. Results were analysed using one-way analysis of variance and Tukey's HSD test. Comparable yields, by mass, were achieved by both straight lance and coring techniques (P > 0.05). Significantly greater yield was achieved with a multiplanar technique (P sampling increases mass yield of tissue in fine-needle sampling. Coring appears to have little bearing on yield.

  17. Novel approach to fault-tolerant logic and yield enhancement

    Energy Technology Data Exchange (ETDEWEB)

    Takefuji, Y.; Adachi, Y.; Aiso, H.

    1982-01-01

    A design technique for improving reliability in function of a gate is proposed, in which a plurality of conventional logic circuits (gates) are used so as to give redundancy to a logic circuit itself. The gate with redundancy designed on the basis of the proposed technique is called the fault-tolerant gate (FTG) in this paper. The FTG has a recovery function with respect to a wider variety of faults. It is much more powerful than that offered by the TMR (triple modular redundancy) circuits. Therefore, the highly reliable logic circuits can be realized, and when the concept of FTGs is applied to vlsi chips the production yield must be enhanced. This paper is divided into three parts. In the first part, concrete methods to realize FTGs are described. The second part proves that the reliability of the gates can be improved by employing the concept of FTGs. In the last part, it is shown that the FTG contributes to the yield enhancement of vlsi chips. 13 references.

  18. Yield and Solidification of Yield-Stress Materials in Rigid Networks and Porous Structures

    CERN Document Server

    Sochi, Taha

    2013-01-01

    In this paper, we address the issue of threshold yield pressure of yield-stress materials in rigid networks of interconnected conduits and porous structures subject to a pressure gradient. We compare the results as obtained dynamically from solving the pressure field to those obtained statically from tracing the path of the minimum sum of threshold yield pressures of the individual conduits by using the threshold path algorithms. We refute criticisms directed recently to our previous findings that the pressure field solution generally produces a higher threshold yield pressure than the one obtained by the threshold path algorithms. Issues related to the solidification of yield stress materials in their transition from fluid phase to solid state have also been investigated and assessed as part of the investigation of the yield point.

  19. Diagnostic Yield of Fiberoptic Bronchoscopy (FOB in Three Common Lung Conditions at a Rural Teaching Hospital

    Directory of Open Access Journals (Sweden)

    Nimit V Khara

    2013-08-01

    Conclusion: Routine flexible bronchoscopy technique has a reasonably high diagnostic yield in current clinical practice. Our study concludes that the diagnostic yield of FOB at our rural setting is comparable with the studies from other centres within the country and abroad. The procedure is more useful in diagnosis when combined with a sound clinical judgment and other supportive investigations. [Natl J Med Res 2013; 3(4.000: 392-395

  20. Central Bank Communication and the Yield Curve

    DEFF Research Database (Denmark)

    Leombroni, Matteo; Vedolin, Andrea; Venter, Gyuri

    We extract novel measures of ECB target rate announcement and communications shocks using high frequency data on money market rates and study their impact on yields of Eurozone countries. We find that (i) target rate shocks have little effect on changes in bond yields of Eurozone countries, while...... communication shocks have a significant impact, with intermediate maturities being affected the most; (ii) positive (negative) communication shocks significantly lower (raise) the yield spread between the peripheral and core countries; (iii) this cross-sectional difference arises after the 2008 financial crises......; (iv) higher credit risk amplifies the effect of communication shocks, and more so for core countries. We rationalize these findings in a parsimonious international term structure model in which interest rates are determined by the interaction between risk-averse arbitrageurs and reaching...

  1. Climate risks on potato yield in Europe

    Science.gov (United States)

    Sun, Xun; Lall, Upmanu

    2016-04-01

    The yield of potatoes is affected by water and temperature during the growing season. We study the impact of a suite of climate variables on potato yield at country level. More than ten climate variables related to the growth of potato are considered, including the seasonal rainfall and temperature, but also extreme conditions at different averaging periods from daily to monthly. A Bayesian hierarchical model is developed to jointly consider the risk of heat stress, cold stress, wet and drought. Future climate risks are investigated through the projection of future climate data. This study contributes to assess the risks of present and future climate risks on potatoes yield, especially the risks of extreme events, which could be used to guide better sourcing strategy and ensure food security in the future.

  2. Evaluation of trends in wheat yield models

    Science.gov (United States)

    Ferguson, M. C.

    1982-01-01

    Trend terms in models for wheat yield in the U.S. Great Plains for the years 1932 to 1976 are evaluated. The subset of meteorological variables yielding the largest adjusted R(2) is selected using the method of leaps and bounds. Latent root regression is used to eliminate multicollinearities, and generalized ridge regression is used to introduce bias to provide stability in the data matrix. The regression model used provides for two trends in each of two models: a dependent model in which the trend line is piece-wise continuous, and an independent model in which the trend line is discontinuous at the year of the slope change. It was found that the trend lines best describing the wheat yields consisted of combinations of increasing, decreasing, and constant trend: four combinations for the dependent model and seven for the independent model.

  3. Spin-dependent np {yields}pn amplitude estimated from dp{yields}ppn

    Energy Technology Data Exchange (ETDEWEB)

    Glagolev, V.V.; Khvastunov, M.S.; Ladygina, N.B.; Piskunov, N.M. [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Hlavacova, J. [Technical University, Park Komenskeho 2, SK-04200, Kosice (Slovakia); Martinska, G.; Urban, J. [University of P.J. Safarik, Jesenna 5, SK-04154 Kosice (Slovakia); Musinsky, J. [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); University of P.J. Safarik, Jesenna 5, SK-04154 Kosice (Slovakia); Pastircak, B. [Institute of Experimental Physics SAS, Watsonova 47, SK-04353, Kosice (Slovakia); Siemiarczuk, T. [Institute of Nuclear Studies,ul. Hoza 69, Warsaw, PL-00 681 (Poland)

    2002-12-01

    An estimation of the spin-dependent part of the np{yields}pn charge exchange amplitude was made on the basis of dp{yields}(pp)n data, taken at 1.67 GeV/c per nucleon in a full solid-angle arrangement. The np{yields}pn amplitude turned out to be entirely spin-dependent. This result shows new possibilities for experiments using polarized deuteron beams and polarized proton targets. (orig.)

  4. yield and yield componemts of extra early maize (zea mays l.)

    African Journals Online (AJOL)

    SHARIFAI

    yielded the control but at par with 4 and 6 t ha-1 in most of the yield attributes. The optimum yield .... basal fertilizer application of 19.97 kg K ha-1 (45 kg. K2O) and 37.35 kg P ... of urea (46%N) was applied in two split doses as per treatment at 3 and 5 WAS ..... holding capacity of soil and are source of slow-release nutrient.

  5. Yield improvement and defect reduction in steel casting

    Energy Technology Data Exchange (ETDEWEB)

    Kent Carlson

    2004-03-16

    This research project investigated yield improvement and defect reduction techniques in steel casting. Research and technology development was performed in the following three specific areas: (1) Feeding rules for high alloy steel castings; (2) Unconventional yield improvement and defect reduction techniques--(a) Riser pressurization; and (b) Filling with a tilting mold; and (3) Modeling of reoxidation inclusions during filling of steel castings. During the preparation of the proposal for this project, these areas were identified by the High Alloy Committee and Carbon and Low Alloy Committee of the Steel Founders' Society of America (SFSA) as having the highest research priority to the steel foundry industry. The research in each of the areas involved a combination of foundry experiments, modeling and simulation. Numerous SFSA member steel foundries participated in the project through casting trials and meetings. The technology resulting from this project will result in decreased scrap and rework, casting yield improvement, and higher quality steel castings produced with less iteration. This will result in considerable business benefits to steel foundries, primarily due to reduced energy and labor costs, increased capacity and productivity, reduced lead-time, and wider use and application of steel castings. As estimated using energy data provided by the DOE, the technology produced as a result of this project will result in an energy savings of 2.6 x 10{sup 12} BTU/year. This excludes the savings that were anticipated from the mold tilting research. In addition to the energy savings, and corresponding financial savings this implies, there are substantial environmental benefits as well. The results from each of the research areas listed above are summarized.

  6. Quality and Yield of Cannabis Products

    DEFF Research Database (Denmark)

    Kastorp, Grith; Lindholst, Christian

    2011-01-01

    Abstract. 180 seizures containing 667 different samples of cannabis products from 5 police districts in Jutland were examined from 2008 to the present. The samples were divided into the groups: hashish, marihuana (leaves and buds) and whole plants (indoors and outdoors). Cannabis seized from indoor...... cultivation was examined in order to determine THC content and yield. The results are used by the Danish Police Attorney to estimate expected yields in cases with unripe cannabis plants. The results indicate that the THC content found in locally grown marihuana is slightly higher than in hashish. However...

  7. Groundwater subsidies and penalties to corn yield

    Science.gov (United States)

    Zipper, S. C.; Booth, E.; Loheide, S. P.

    2013-12-01

    Proper water management is critical to closing yield gaps (observed yield below potential yield) as global populations continue to expand. However, the impacts of shallow groundwater on crop production and surface processes are poorly understood. The presence of groundwater within or just below the root zone has the potential to cause (via oxygen stress in poorly drained soils) or eliminate (via water supply in dry regions) yield gaps. The additional water use by a plant in the presence of shallow groundwater, compared to free drainage conditions, is called the groundwater subsidy; the depth at which the groundwater subsidy is greatest is the optimal depth to groundwater (DTGW). In wet years or under very shallow water table conditions, the groundwater subsidy is likely to be negative due to increased oxygen stress, and can be thought of as a groundwater penalty. Understanding the spatial dynamics of groundwater subsidies/penalties and how they interact with weather is critical to making sustainable agricultural and land-use decisions under a range of potential climates. Here, we examine patterns of groundwater subsidies and penalties in two commercial cornfields in the Yahara River Watershed, an urbanizing agricultural watershed in south-central Wisconsin. Water table levels are generally rising in the region due to a long-term trend of increasing precipitation over the last several decades. Biophysical indicators tracked throughout both the 2012 and 2013 growing seasons show a strong response to variable groundwater levels on a field scale. Sections of the field with optimal DTGW exhibit consistently higher stomatal conductance rates, taller canopies and higher leaf area index, higher ET rates, and higher pollination success rates. Patterns in these biophysical lines of evidence allow us to pinpoint specific periods within the growing season that plants were experiencing either oxygen or water stress. Most importantly, groundwater subsidies and penalties are

  8. Amplitude Models for Discrimination and Yield Estimation

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, William Scott [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-01

    This seminar presentation describes amplitude models and yield estimations that look at the data in order to inform legislation. The following points were brought forth in the summary: global models that will predict three-component amplitudes (R-T-Z) were produced; Q models match regional geology; corrected source spectra can be used for discrimination and yield estimation; three-component data increase coverage and reduce scatter in source spectral estimates; three-component efforts must include distance-dependent effects; a community effort on instrument calibration is needed.

  9. Experimental assessment of bacterial storage yield

    DEFF Research Database (Denmark)

    Karahan-Gül, Ö.; Artan, N.; Orhon, D.;

    2002-01-01

    An experimental procedure was developed for the respirometric determination of bacterial storage yield as defined in the Activated Sludge Model No. 3. The proposed approach is based on the oxygen utilization rate (OUR) profile obtained from a batch test and correlates the area under the OUR curve...... to the amount of oxygen associated with substrate storage. Model simulation was used to evaluate the procedure for different initial experimental conditions. The procedure was tested on acetate. The same storage yield value of 0.76 gCOD/gCOD was calculated for two experiments, starting with different F/M ratios...

  10. PREOVULATORY FOLLICLE DEVELOPMENT IN HIGH YIELDING COWS

    Directory of Open Access Journals (Sweden)

    Radovan Tomášek

    2013-06-01

    Full Text Available The aim of the study was to examine the development of preovulatory follicles in pregnant and non-pregnant high yielding cows. The treatment by supergestran and oestrophan was used to synchronize the estrous cycle. Ovaries were monitored by transrectal ultrasonography. The linear increase of preovulatory follicles was observed in pregnant (P < 0,001 and non-pregnant (P < 0,001 cows during 8 days before ovulation. In conclusion, preovulatory follicles in pregnant and non-pregnant high yielding cows developed similarly.

  11. Airborne monitoring of crop canopy temperatures for irrigation scheduling and yield prediction

    Science.gov (United States)

    Millard, J. P.; Jackson, R. D.; Reginato, R. J.; Idso, S. B.; Goettelman, R. C.; Lapado, R. L.

    1977-01-01

    The aim of the program discussed was to develop techniques for remotely measuring crop irrigation needs and predicting crop yields, with emphasis on wheat. Airborne measurements, using an IR line scanner and color IR photography, were made to evaluate the feasibility of measuring minimum and maximum (dawn and afternoon) crop temperatures to compute a parameter, termed 'stress degree day' (SDD) - a valuable indicator of crop water needs, which can be related to irrigation scheduling and yield. Crop canopy temperature measurements by airborne IR techniques revealed the superiority of thermal IR data over color IR photography. Water stress undetected in the latter technique was clearly detected in thermal imagery. Color IR photography, however, is valuable in discerning vegetation. The pseudo-colored temperature-difference images (and pseudo-colored images, reading directly in daily SDD increments) are shown to be well suited for assessing plant water status and, thus, for determining the irrigation needs and crop yield potentials.

  12. Yielding and post-yield behaviour of closed-cell cellular materials under multiaxial dynamic loading

    Science.gov (United States)

    Vesenjak, Matej; Ren, Zoran

    2016-05-01

    The paper focuses on characterisation of yielding and post-yield behaviour of metals with closed-cell cellular structure when subjected to multiaxial dynamic loading, considering the influence of the relative density, base material, strain rate and pore gas pressure. Research was conducted by extensive parametric fully-coupled computational simulations using the finite element code LS-DYNA. Results have shown that the macroscopic yield stress of cellular material rises with increase of the relative density, while its dependence on the hydrostatic stress decreases. The yield limit also rises with increase of the strain rate, while the hydrostatic stress influence remains more or less the same at different strain-rates. The macroscopic yield limit of the cellular material is also strongly influenced by the choice of base material since the base materials with higher yield limit contribute also to higher macroscopic yield limit of the cellular material. By increasing the pore gas filler pressure the dependence on hydrostatic stress increases while at the same time the yield surface shifts along the hydrostatic axis in the negative direction. This means that yielding at compression is delayed due to influence of the initial pore pressure and occurs at higher compressive loading, while the opposite is true for tensile loading.

  13. Application of Imaging Techniques to Mechanics of Materials and Structures, Volume 4 : Proceedings of the 2010 Annual Conference on Experimental and Applied Mechanics

    CERN Document Server

    2013-01-01

    This the fourth volume of six from the Annual Conference of the Society for Experimental Mechanics, 2010, brings together 58 chapters on Application of Imaging Techniques to Mechanics of Materials and Structure. It presents findings from experimental and computational investigations involving a range of imaging techniques including Recovery of 3D Stress Intensity Factors From Surface Full-field Measurements, Identification of Cohesive-zone Laws From Crack-tip Deformation Fields, Application of High Speed Digital Image Correlation for Vibration Mode Shape Analysis, Characterization of Aluminum Alloys Using a 3D Full Field Measurement, and Low Strain Rate Measurements on Explosives Using DIC.

  14. Four Flaps Technique for Neoumbilicoplasty

    Directory of Open Access Journals (Sweden)

    Young Taek Lee

    2015-05-01

    Full Text Available The absence or disfigurement of the umbilicus is both cosmetically and psychologically distressing to patients. The goal of aesthetically pleasing umbilical reconstruction is to create a neoumbilicus with sufficient depth and good morphology, with natural-looking superior hooding and minimal scarring. Although many reports have presented techniques for creating new and attractive umbilici, we developed a technique that we term the "four flaps technique" for creating a neoumbilicus in circumstances such as the congenital absence of the umbilicus or the lack of remaining umbilical tissue following the excision of a hypertrophic or scarred umbilicus. This method uses the neighboring tissue by simply elevating four flaps and can yield sufficient depth and an aesthetically pleasing shape with appropriate superior hooding.

  15. Evaluation of Yield Maps Using Fuzzy Indicators

    Science.gov (United States)

    This paper presents a new methodology for the evaluation of yield maps using fuzzy indicators, which takes into account atypical phenomena and expert opinions regarding the maps. This methodology could allow for improved methods for deciding boundary locations for precision application of production...

  16. Expectations, Bond Yields and Monetary Policy

    DEFF Research Database (Denmark)

    Chun, Albert Lee

    2011-01-01

    expectations about inflation, output growth, and the anticipated path of monetary policy actions contain important information for explaining movements in bond yields. Estimates from a forward-looking monetary policy rule suggest that the central bank exhibits a preemptive response to inflationary expectations...

  17. 6-Benzyladenine enhancements of cotton yield

    Science.gov (United States)

    The influence of applied plant growth regulators (PGR) on growth, development and yield in cotton (Gossypium hirsutum L. and Gossypium barbadense L.) has been studied for over half a century. A recent study suggested that cytokinin treatment of young cotton seedlings may enhance overall performanc...

  18. MITE INCIDENCE AND CROP YIELD IN ZIMBABWE

    African Journals Online (AJOL)

    control, as well as damage and yield of tomatoes were investigated in two important tomato production areas of ... Mutoko, while the pruned and trellised plots had 4.6 and 17.3 mites per leaf. ..... therefore, insecticide deposit on the leaves was.

  19. Effects of water management on crop yield

    NARCIS (Netherlands)

    Hack-ten Broeke, M.J.D.; Bartholomeus, R.; Kroes, J.G.; Dam, van J.C.; Bakel, van J.

    2015-01-01

    A new instrument for the quantification of agricultural crop yield reduction due to too wet, too dry or too salty conditions: what kind of instrument should that be? And could such an instrument be usable for the calculation of effects of climate scenarios? WaterVision Agriculture should be the answ

  20. Electricity yield simulation of complex BIPV systems

    NARCIS (Netherlands)

    Sprenger, W.

    2013-01-01

    Building-integrated photovoltaic systems (BIPV) are able to improve the energy balance of buildings. However, this improvement can be analyzed quantitatively only if the electricity yield generated by the BIPV system is calculated. This PhD thesis presents a simulation program that calculates the