WorldWideScience

Sample records for technique des industries

  1. La technique de la titrisation : un outil pertinent de financement des industries minières ?

    OpenAIRE

    Yves Jégourel

    2015-01-01

    La stratégie d’intégration verticale des producteurs miniers nécessite de trouver les conditions de son financement. De nombreux schémas sont pour cela envisageables et la technique de la titrisation, bien que largement stigmatisée depuis la crise financière de 2008, doit être considérée. Plusieurs conditions doivent cependant être réunies et il est peu probable que la titrisation hors-bilan s’affirme, sous sa forme actuelle, comme un des modes importants de financement des capacités de produ...

  2. Industrial technique

    International Nuclear Information System (INIS)

    Robertson, D.H.

    1975-01-01

    Techniques for selectively extracting and storing only krypton and xenon in the waste gases that are released from a pressurized water nuclear power reactor are described. The illustrative fluorocarbon absorption system has three separation stages: an initial gas-fluorocarbon absorber, a flash chamber and fractionator for segregating all of the absorbed gases from the loaded absorber stage fluorocarbon (save for the krypton and xenon), and a stripper that receives the partially loaded fluorocarbon liquid directly from the fractionator in order to separate only the krypton and xenon. A molecular sieve filter dries the input process gas, a cartridge type solvent filter is used to remove radiation degradation products from the loaded liquid that flows from the absorber, a cold trap gas drier is provided to remove residual solvent vapor from the separated krypton and xenon, and radiation detectors automatically activate valves to establish safe conditions in the event of an accident or plant failure. (U.S.)

  3. Industrial technique

    International Nuclear Information System (INIS)

    Jabsen, F.S.

    1975-01-01

    An illustrative embodiment of the invention discloses a technique for disassembling a nuclear reactor fuel element without destroying the individual fuel pins and other structural components from which the element is assembled. A traveling bridge and trolley that span a water-filled spent fuel storage pool support a strongback. The strongback is under water and provides a working surface on which the spent fuel element is placed for inspection and for the manipulation that is associated with disassembly and assembly. To remove, in a non-destructive manner, the grids that hold the fuel pins in the proper relative positions within the element, bars are inserted through apertures in the grids with the aid of special tools. These bars are rotated to flex the adjacent grid walls and, in this way relax the physical engagement between protruding portions of the grid walls and the associated fuel pins. With the grid structure so flexed to relax the physical grip on the individual fuel pins, these pins can be withdrawn for inspection or replacement as necessary without imposing a need to destroy fuel element components. (U.S.)

  4. Applications des techniques de diffusion de la lumière, des rayons X et des neutrons a l'étude des systèmes colloïdaux. Troisième partie : caractérisation des microémulsions et des composés solides. Étude de différents systèmes d'intérêt industriel Application of Light, X-Ray and Neutron Diffusion Techniques to the Study of Colloidal Systems. Part Three: Microemulsions, Solid Materials, Liquids and Miscellaneous Systems with Industrial Uses

    Directory of Open Access Journals (Sweden)

    Espinat D.

    2006-11-01

    Full Text Available Cette troisième partie clôt une revue bibliographique concernant la caractérisation des systèmes colloïdaux par les techniques de diffusion (lumière, rayons X, neutrons (Rev. Inst. Franç. du Pétrole, Vol. 45, No 6, novembre-décembre 1990. Nous poursuivrons cette présentation en nous intéressant aux microémulsions. Après la présentation des informations que l'on peut obtenir sur les systèmes polymériques, les solutions micellaires ou les systèmes fractals, qui ont fait l'objet de multiples travaux, nous reviendrons sur les applications plus restreintes à des systèmes colloïdaux parfois moins bien définis et d'origine industrielle, telles les fractions lourdes des pétroles, les asphaltènes ou encore les additifs de lubrification. Les possibilités de la diffusion des rayons X et des neutrons à l'étude de matériaux solides seront présentées à travers la caractérisation des solides poreux et en particulier des catalyseurs. Nous terminerons cette présentation par les liquides purs ou les mélanges; les techniques de diffusion ont contribué fortement à la description des structures des phases liquides. This article is the second one (the first one was published in Revue de l'Institut Français du Pétrole No. 6, November-December 1990 concerning the application of techniques of light scattering, X rays and neutrons to the analysis of colloidal systems and more specifically to the theoretical description of the three methods. The aim of this second part is to make a nonexhaustive description of several fields of applications. A special effort is made to describe the potential of these methods for characterizing colloidal or divided systems encountered in a great many activities involving the petroleum industry. The first part of this article takes up polymer and colloidal solutions. Particular attention is paid to the importance of scattering techniques for characterizing polymers in solution and micellar solutions. A

  5. Cartographie des zones d'intervention des partenaires techniques et ...

    African Journals Online (AJOL)

    cartographier les zones d'intervention des partenaires techniques et financiers au Bénin. L'approche méthodologique utilisée a consisté à la recherche documentaire, à la collecte de données auprès des partenaires techniques et financiers et à l'analyse de ces données. Les résultats ont permis de constater que cent dix ...

  6. Nuclear techniques in industry

    International Nuclear Information System (INIS)

    Hammad, F.H.

    1994-01-01

    Nuclear techniques are utilized in almost every industry. The discussion in this paper includes discussions on tracer methods and uses nucleonic control systems technology; non-destructive testing techniques and radiation technology. 1 fig., 2 tabs

  7. Training techniques for industry

    International Nuclear Information System (INIS)

    Jones, D.W.

    1978-01-01

    The advantages and disadvantages of commonly used training techniques in relation to cost-effective, prevention-oriented Quality Assurance are examined. Important questions are whether training techniques teach cost effectiveness and whether the techniques are, themselves, cost effective. To answer these questions, criteria for evaluating teaching techniques for cost effectiveness were developd, and then commonly used techniques are evaluated in terms of specific training program objectives. Motivation of personnel is also considered important to the success of a training program, and methods are outlined by which recognition of the academic quality of industrial training can be used as a motivational technique

  8. Nitrous Oxide Formation and Destruction by Industrial No Abatement Techniques Including Scr Emissions des protoxides d'azote par des techniques industrielles d'abattement de NO y compris le SCR

    Directory of Open Access Journals (Sweden)

    De Soete G. G.

    2006-11-01

    'investigations systématiques concernant les émissions de N2O d'unités de combustion stationnaire d'échelle industrielle, équipées de technologies d'abatement de NO. Les études effectuées en laboratoire, présentées ici, suggèrent que des techniques d'étagement du combustible, de réduction sélective non catalytique (NCSR et catalytique (CSR du NO, doivent être considérées comme des sources potentielles d'augmentation des émissions de protoxyde d'azote. L'étude utilise un réacteur (fig. 1 permettant l'étagement de flammes laminaires C2H4/O2/Ar en deux fractions Fl et F2, respectivement caractérisées par un débit D1 et D2 et une richesse R1 et R2; Rg désigne la richesse globale des deux fractions. La fraction Fl brûle sous forme de flamme de prémélange plate sur un brûleur (B1 constitué d'une plaque en bronze fritté; la fraction F2, injecté dans une double couronne à points d'injection multiples (B2 brûle sous forme de flamme de diffusion, après mélange avec les produits de combustion de la fraction Fl. La distance (X entre les deux brûleurs B1 et B2 est variable. 1. Formation de N2O due à l'étagement du combustible Le monoxyde d'azote est introduit en prémélange avec la fraction Fl. Sa concentration après mélange avec les produits de combustion de Fl est désignée par NOin. La figure 2 donne la fraction de l'azote du NO transformée en N2O (Fn en fonction de R1 avec Rg comme paramètre. Les températures mesurées au point d'injection (Tx y correspondant sont présentées sur la figure 3. On observe (1 qu'une séquence de stratification riche - pauvre est généralement plus favorable à la formation de N2O qu'une séquence pauvre - riche (fig. 1, (2 que Fn diminue lorsque Tx augmente (fig. 4 et 5 ou lorsque la concentration de l'oxygène décroît (fig. 6. Ces tendances, généralement observées dans le cas de la combustion en phase gazeuse, s'expliquent qualitativement par les réactions principales de formation et de destruction du N2O

  9. Modelisation des effets physico-techniques pour la conception des ...

    African Journals Online (AJOL)

    automatisation dans les installations industrielles a besoin d'une régulation automatique des commandes des processus technologiques pour lesquelles certaines contraintes sont à relever compte tenu des exigences des innovations scientifiques de ...

  10. Accès à l'eau : des solutions techniques et sociales aident des ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Grâce à la modélisation par ordinateur faisant appel à des techniques de pointe et à la consultation des collectivités, l'organisme bolivien Agua Sustentable a trouvé des solutions politiques à des conflits qui auraient pu s'avérer désastreux au sujet de l'accès à l'eau. Cet organisme de recherche subventionné par le CRDI a ...

  11. normes techniques et pratiques locales des producteurs dans les ...

    African Journals Online (AJOL)

    ACSS

    pour objectif d'analyser l'évolution des normes techniques de la production du riz et les pratiques locales dans les périmètres .... des systèmes de production agricole et du riz dans les ..... recommandations de l'encadrement technique local.

  12. Nuclear techniques in industry

    International Nuclear Information System (INIS)

    Barnette, P.

    The long term development and successful utilization of the Tongonan geothermal field for electric power generation is ultimately a function of the response of the reservoir to extensive exploitation. A field drawdown test of several years duration has been planned to test this response. A number of nuclear chemical techniques have been incorporated into this to assist in quantitatively tracing the subsurface movements of both reservoir and reinjected fluids; and to provide an early warning of changes in the physical and chemical properties of the reservoir fluids with respect to natural recharge. The programme will be implemented by Philippine Atomic Energy Commission (PAEC) under contract to Philippine National Oil Company - Energy Development Corporation (PNOC-EDC). (author)

  13. Technique of nuclear reactors controls; Technique des controles des reacteurs nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Weill, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1953-12-15

    This report deal about 'Techniques of control of the nuclear reactors' in the goal to achieve the control of natural uranium reactors and especially the one of Saclay. This work is mainly about the measurement into nuclear parameters and go further in the measurement of thermodynamic variables,etc... putting in relief the new features required on behalf of the detectors because of their use in the thermal neutrons flux. In the domain of nuclear measurement, we indicate the realizations and the results obtained with thermal neutron detectors and for the measurement of ionizations currents. We also treat the technical problem of the start-up of a reactor and of the reactivity measurement. We give the necessary details for the comprehension of all essential diagrams and plans put on, in particular, for the reactor of Saclay. (author) [French] Nous avons aborde le probleme de la ''Technique du Controle des reacteurs nucleaires'' dans le but de realiser le controle du reacteur de Saclay. C'est ainsi que nous avons ete amene a etudier le probleme dans son ensemble, tel qu'il se pose pour tout reacteur a uranium naturel. Ce travail traite principalement du domaine des mesures a caractere nucleaire et s'etend dans le domaine des mesures thermodynamque de niveaux, etc... mettant en relief les caracteristiques nouvelles exigees de la part des detecteurs du fait de leur utilisation dans le flux de neutrons thermiques. Dans le domaine de mesures nucleaires, nous indiquons principalement les realisations et les resultats obtenus pour les detecteurs de neutrons thermiques et pour la mesure de courants d'ionisations. Nous traitons egalement du probleme technique du demarrage d'un reacteur et du probleme de la mesure de la reactivite. Nous donnons les details necessaires a la comrehension de tous les schemas et plans de cablages essentiels mis au point, en particulier, pour le reacteur de Saclay. (auteur)

  14. Les techniques de coloration et de screening des frottis cervicaux ...

    African Journals Online (AJOL)

    Les techniques de coloration et de screening des frottis cervicaux. ... précocement tout cancer du col de l'utérus par la mise en évidence des lésions ... in terms of frequency, the second cancer concerning the women after the breast cancer.

  15. Tracer techniques in food industry

    International Nuclear Information System (INIS)

    Pertsovskij, E.S.; Sakharov, Eh.V.; Dolinin, V.A.

    1980-01-01

    The appicability of radioactive tracer techniques to process control in food industry are considered. Investigations in the field of food industry carried out using the above method are classified. The 1 class included investigations with preliminary preparation of a radioactive indicator and its following introduction in the system studied. The 2 class includes investigations based on the introduction in the system studied of a non-active indicator which is activated in a neutron flux being in samples selected in or after the process investigated. The 3 class includes studies based on investigations of natural radioactivity of certain nuclides in food stuff. The application of tracer techniques to the above classes of investigations in various fields of food industry and the equipment applied are considered in detail [ru

  16. INDUSTRIE ET ENVIRONNEMENT Les préoccupations environnementales de l’industrie des corps gras

    Directory of Open Access Journals (Sweden)

    Pages Xavier

    2002-09-01

    Full Text Available Les préoccupations environnementales de l’industrie des corps gras sont principalement rythmées par le renforcement des contraintes réglementaires et concernent tous les aspects environnementaux : effluents gazeux et aqueux, déchets, management, énergie. Ces aspects sont inégalement présents dans les différents sous-secteurs de l’industrie des corps gras ; quelques exemples sont présentés. La réduction des émissions de COV (composés organiques volatils et les nuisances olfactives sont une problématique concernant principalement l’activité de trituration, la lipochimie et la fonte de corps gras animaux. Des valeurs limites de consommation de solvant sont maintenant imposées réglementairement en extraction; la prise en compte de problèmes de nuisance olfactive donnent lieu à l’amélioration des procédés de traitement d’air (corps gras animaux ou à leur mise en place progressive (trituration de colza. La gestion des déchets reste une préoccupation essentielle pour l’ensemble de la profession et tout particulièrement pour les secteurs des corps gras animaux et la lipochimie, en raison de la remise en cause des filières d’élimination due au renforcement des contraintes réglementaires, mais aussi en raison des coûts de traitement. Ce poste ne doit pas être négligé par les entreprises : réduction à la source, recherche de filières pérennes, valorisation énergétique ou matière sont des éléments permettant également une réduction significative des coûts. La maîtrise de la consommation d’énergie est un élément important, voir stratégique, notamment dans le secteur de la trituration des graines oléagineuses. Des actions de sensibilisation permettent de poursuivre également l’effort auprès des PME, actuellement moins impliquées. En matière de traitement d’eau, des avancées notables sont observées depuis une décennie ; néanmoins certaines difficultés persistent, notamment dans les

  17. Prevention of air pollution: guidebook of the French techniques of dedusting and purification of gases and smokes in the industry; Prevention de la pollution de l'air: guide des techniques francaises de depoussierage et d'epuration des gaz et fumees dans l'industrie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This new edition favours the multi-pollutants approach and integrates the improvements made in the European standardization of emission measurements. It contributes to the diffusion of the French techniques in the domain of gases dedusting and purification. (J.S.)

  18. Industrial applications of radioisotope techniques in Poland

    International Nuclear Information System (INIS)

    Michalik, J.St.

    1985-01-01

    A general review of applications of radioisotope techniques in the Polish industry for about 25 years is given. The radiotracer methods used in metallurgy, hydrometallurgy, glass industry, oil and petroleum industries, in material testing and in other industries are described. Neutron activation analysis methods as well as nuclear gauges for industry (thickness meters, density meters, conveyer belt weigher, acid concentration meters and others) are also presented. The economic advantages of industrial applications of radioisotope techniques are described too. 42 refs., 43 figs., 11 tabs. (author)

  19. Industrial application of nuclear techniques in Australia

    International Nuclear Information System (INIS)

    Easey, J.F.

    1981-01-01

    The applications of nuclear techniques in Australia was reviewed - the work has been to aid: mining and mineral sector, the manufacturing, chemical and petroleum industries, hydrology and sedimentology

  20. Industrial applications of nuclear techniques in Poland

    International Nuclear Information System (INIS)

    Michalik, J.St.

    1981-01-01

    Application of radioisotope techniques in a number of Polish industries was reviewed. Studies on the usage of radiotracer as an evaluation method for technological processes were carried out and the advantages of such application were discussed

  1. Techniques d'inspection par ondes guidees ultrasonores d'assemblages brases dans des reacteurs aeronautiques =

    Science.gov (United States)

    Comot, Pierre

    L'industrie aeronautique, cherche a etudier la possibilite d'utiliser de maniere structurelle des joints brases, dans une optique de reduction de poids et de cout. Le developpement d'une methode d'evaluation rapide, fiable et peu couteuse pour evaluer l'integrite structurelle des joints apparait donc indispensable. La resistance mecanique d'un joint brase dependant principalement de la quantite de phase fragile dans sa microstructure. Les ondes guidees ultrasonores permettent de detecter ce type de phase lorsqu'elles sont couplees a une mesure spatio-temporelle. De plus la nature de ce type d'ondes permet l'inspection de joints ayant des formes complexes. Ce memoire se concentre donc sur le developpement d'une technique basee sur l'utilisation d'ondes guidees ultrasonores pour l'inspection de joints brases a recouvrement d'Inconel 625 avec comme metal d'apport du BNi-2. Dans un premiers temps un modele elements finis du joint a ete utilise pour simuler la propagation des ultrasons et optimiser les parametres d'inspection, la simulation a permis egalement de demontrer la faisabilite de la technique pour la detection de la quantite de phase fragile dans ce type de joints. Les parametres optimises sont la forme de signal d'excitation, sa frequence centrale et la direction d'excitation. Les simulations ont montre que l'energie de l'onde ultrasonore transmise a travers le joint aussi bien que celle reflechie, toutes deux extraites des courbes de dispersion, etaient proportionnelles a la quantite de phase fragile presente dans le joint et donc cette methode permet d'identifier la presence ou non d'une phase fragile dans ce type de joint. Ensuite des experimentations ont ete menees sur trois echantillons typiques presentant differentes quantites de phase fragile dans le joint, pour obtenir ce type d'echantillons differents temps de brasage ont ete utilises (1, 60 et 180 min). Pour cela un banc d'essai automatise a ete developpe permettant d'effectuer une analyse similaire

  2. Industrial level measurement techniques - a review

    International Nuclear Information System (INIS)

    Schaudel, D.E.

    1984-01-01

    The outlined methods of industrial level measurement technique are nowadays in current use. In correspondence with the technical evolution the mechanical techniques are mentioned first, followed by a description of the more modern electronic methods. These measurement methods comply especially to the requirements of computer aided process guiding systems, i.e. compatibility of signals, self-checking and reliability. (orig.) [de

  3. Industrial radiography techniques and their applications

    International Nuclear Information System (INIS)

    Wamorkar, R.R.

    1981-01-01

    Various aspects of industrial radiography are discussed. These include: radiation sources, geometrical unsharpness of image, radiation attenuation in the specimen, radiation effect of film, types of film, intensifying screens, exposure time calculations, source to film distance and sensivitity. Radiography techniques for examination of welded joints on flat plate and pipes or cylindrical objects, and castings are indicated. Applications of radiography in various industries are mentioned. (M.G.B.)

  4. Nuclear techniques in coal and chemical industries

    International Nuclear Information System (INIS)

    Elbern, A.W.; Leal, C.A.

    1980-01-01

    The use of nuclear techniques for the determination of important parameters in industrial installations is exemplified; advantages of these techniques over other methods conventionally used are pointed out. The use of radiotracers in the study of physical and chemical phenomena occurring in the chemical industry is discussed. It is also shown that, using certain radioisotopes, it is possible to construct devices which enable, for example, the determination of the ash content in coal samples. These devices are economical and easy to be installed for the on-line control during coal transportation. (C.L.B.) [pt

  5. Industrial applications of radioisotopes: techniques and procedures of (NTIS) Nuclear Techniques Industrial Service

    International Nuclear Information System (INIS)

    Smith, S.W.; Kruger, J.

    1985-06-01

    Radioisotope handling procedures followed by personnel of the Nuclear Techniques Industrial Service (NTIS) during the conduction of investigations in industry are described. Possible radiological implications as a result of the various measuring techniques and different types of plants are discussed. Conditions under which permanent authorization has been granted for the use of radioisotopes are mentioned

  6. Economics on nuclear techniques application in industry

    International Nuclear Information System (INIS)

    Kato, Masao

    1979-01-01

    The economics of the application of nuclear techniques to industry is discussed. Nuclear techniques were applied to gauging (physical measurement), analysis, a radioactive tracer method, electrolytic dissociation, and radiography and were found to be very economical. They can be applied to manufacturing, mining, oceano-engineering, environmental engineering, and construction, all of which have a great influence on economics. However, because the application of a radioactive tracer technique does not have a direct influence on economics, it is difficult to estimate how beneficial it is. The cost-benefit ratio method recommended by IAEA was used for economical calculations. Examples of calculations made in gauging and analysis are given. (Ueda, J.)

  7. Development of Radiotracer Techniques in Industry

    International Nuclear Information System (INIS)

    Wardono

    2000-01-01

    Contribution of radiotracer techniques to solve problems in industrial process plants have been recognized since a long time. Radiotracer application was governed by three main components, namely radioisotopes, radiation detection and data interpretation of an experiment. The three main components mentioned above have been continually developed to overcome problems relating to the operation of industrial process plants. The availability of isotope generator is one of the development aspect in radiotracer technique. Radiation hazard in radiotracer experiment may be reduced by applying isotope generator and on the other hand the delivery of radiotracer to the plant site from the radioisotopes producer was made easier. The development of microprocessor in computer system has facilitated data recording, storing and retrieving. Development in mathematical model supported by radiotracer experiment enhance data interpretation and shed light on various phenomena of flow process. Generally a flow dynamic in a process plant in all kind of industries can be studied using radiotracer technique. However the main challenge coming from petroleum, petrochemical and mineral processing industries

  8. Techniques of industrial radiology in military explosives

    International Nuclear Information System (INIS)

    Alves, L.E.G.

    1985-01-01

    The use of industrial radiology techniques id very important for military explosive fabrication. The cylindrical-ogive bodies made in forged metal have their interior fulfilled with high melted explosive and they must explode when they reach the target. The granades, as these bodies are called, are thrown by cannons and their interior are submitted to high pressures and accelerations which can cause a premature detonation, in most case, in interior of tube, in case of they have defects in explosive mass. The origins of defects, its localization and classification presenting the techniques used and disposable in Brazil are discussed. (M.C.K.) [pt

  9. Utilisation de la Technique D\\'électrophorèse des Protéines Totales ...

    African Journals Online (AJOL)

    Utilisation de la Technique D\\'électrophorèse des Protéines Totales sur Gel de Polyacrylamide-SDS (SDS-PAGE) pour L\\'étude de la Diversité des Rhizobiums D\\'Acacia tortilis (Forsk.) Hayne Subsp. Raddiana (Savi) Brenan.

  10. evaluation technique et economique des formules alimentaires de ...

    African Journals Online (AJOL)

    COMPOSITION CHIMIQUE DES INGREDIENTS. ET ALIMENTS COMPOSES UTILISES. Les résultats de l'analyse chimique des différents ingrédients et aliments (tableau 2) ont montré que les tiges de mil et la paille de riz avaient la même teneur en matière azotée totale (5,7 %) qui était environ la moitié de celle de la fane ...

  11. Nouvelles techniques de mise en valeur des ressources d'hydrocarbures New Techniques for Valorising Hydrocarbon Resources

    Directory of Open Access Journals (Sweden)

    Boy De la Tour X.

    2006-11-01

    Full Text Available Après avoir montré l'importance des réserves de pétrole non conventionnel et l'enjeu que représente pour l'humanité la mise en exploitation de ces ressources, cette étude examine les axes actuels de recherches et l'état de la technologie pour chacune des sources de nouveau pétrole retenues : mers profondes, récupération assistée, huiles lourdes et sables asphaltiques, schistes bitumineux et conversion du charbon. Il en ressort que si les ressources de nouveau pétrole sont considérables, leur mise en valeur nécessitera des investissements très lourds, et le coût du pétrole ainsi produit restera élevé, comparé au coût actuel du pétrole conventionnel. Compte tenu des délais de mise en oeuvre, des problèmes technologiques restant à résoudre et de la nécessité de réaliser des pilotes semi-industriels très coûteux pour expérimenter les nouvelles techniques, il convient de consentir sans attendre un effort important de recherche technologique, impliquant un accroissement sensible des budgets de R&D, mais aussi des incitations financières appropriées. Cet effort de mise au point de technologies adaptées à ces sources d'hydrocarbures sera favorisé par les nouvelles conditions économiques créées par la rareté relative des réserves d'hydrocarbures classiques, à condition que les Etats, par leur politique, favorisent la production de ressources d'hydrocarbures à coût élevé. A l'heure actuelle, on peut évaluer la production de pétrole difficile à environ 100 Mt, l'essentiel étant réalisé dans le domaine des huiles lourdes et de la récupération assistée ; on estime que la production de nouveau pétrole pourrait représenter 200 à 350 Mt en 1990 et se situer entre 600 et 900 Mt en 2000, soit 5 à 8 % de la production de pétrole en 1990 et 15 à 20 % en 2000. Un tel objectif nécessiterait des investissements de l'ordre de 500 à 750 milliards de dollars 1980. After pointing out the importance of

  12. Nuclear analytical techniques in Cuban Sugar Industry

    International Nuclear Information System (INIS)

    Diaz Riso, O.; Griffith Martinez, J.

    1996-01-01

    This paper is a review concerning the applications of Nuclear Analytical Techniques in the Cuban sugar industry. The most complete elemental composition of final molasses (34 elements ) and natural zeolites (38) this last one employed as an auxiliary agent in sugar technological processes has been performed by means of Instrumental Neutron Activation Analysis (INAA) and X-Ray Fluorescence Analysis (XRFA). The trace elements sugar cane soil plant relationship and elemental composition of different types of Cuban sugar (rawr, blanco directo and refine) were also studied. As a result, valuable information referred to the possibilities of using these products in animal and human foodstuff so as in other applications are given

  13. A review of micro-wave techniques in plasma studies; Survol des techniques micro-ondes pour l'etude des plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Consoli, T [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The problem of the application of micro-wave techniques to the study of plasma properties is considered in this report. In section I, the author summarizes a few fundamental laws concerning the theory of waves in an ionised medium as well as measurable effects of transverse and longitudinal propagation. Section II is a rapid review of the experimental methods and of the various measurements which may be effected in very high frequency plasmas. Only recent experimental work carried out since the last U. R.S.I. Assembly is considered. Section III is devoted to micro-wave techniques developed during this period in the laboratories of the Applied Physics Service. These techniques deal with longitudinal propagation and in particular with the propagation along a right mode. Section IV is a general view of similar studies undertaken in European Research Centres working on plasma physics or controlled fusion. Section V is a contribution concerning three particular topics from the Juelich and Max Planck Institute laboratories. (author) [French] On etudie dans ce rapport le probleme de l'application des techniques micro-ondes a l'etude des proprietes d'un plasma. Dans la section I, l'auteur rappelle rapidement quelques lois fondamentales de la theorie des ondes dans un milieu ionise ainsi que les effets mesurables en propagation transversale et longitudinale. La section II est une revue rapide des methodes experimentales et des diverses mesures qui peuvent etre faites dans les plasmas aux tres hautes frequences. On ne considere seulement que les etudes experimentales recentes depuis la derniere assemblee de l'U.R.S.I. La section III est consacree aux techniques hyperfrequences developpees durant la meme periode dans les laboratoires des Services de Physique Appliquee. Ces techniques se rapportent a la propagation longitudinale et particulierement a la propagation suivant le mode droit. La section IV est un panorama de travaux similaires entrepris dans les centres europeens

  14. The industrial production of fuel elements; La fabrication en france des elements combustibles

    Energy Technology Data Exchange (ETDEWEB)

    Boussard, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires; Nadal, J [Societe Industrielle de Combustible Nucleaire (SICN), 75 - Paris (France); Pellen, A [Compagnie pour l' Etude et la Realisation de Combustibles Atomiques (CERCA), 75 - Paris (France)

    1964-07-01

    -pool type reactors. The authors show how the problem of the industrial production of rolled fuel elements has been solved in France, and give the three steps involved: 1 - Assembly of the plates made in the U.S.A., 2 - Rolling of the cores made in the U.S.A. to obtain the plates, 3 - Fabrication of the U-Al alloy and production of the cores. They then recall briefly the characteristics of the different fuel elements now in production. A description is given of the various stages of the production including information about the equipment; stress is laid on the extent of the controls carried out at each stage. In conclusion the authors consider the future development of this type of production taking into account the improvements planned and those which are possible. (authors) [French] Les auteurs traitent successivement de la fabrication industrielle des elements combustibles pour reacteurs de puissance de la filiere U naturel graphite-gaz et plus particulierement pour les centrales energetiques d'E.D.F. et de celle des elements combustibles a base d'U enrichi destines aux reacteurs experimentaux du type 'piscine'. 1ere Partie - LES ELEMENTS COMBUSTIBLES AVANCES POUR LES REACTEURS E.D.F.: Apres un bref rappel des caracteristiques des elements combustibles actuellement fabriques industriellement pour les reacteurs de MARCOULE et de CHINON, les auteurs indiquent les differentes etapes suivies pour aboutir au stade de la fabrication industrielle d'un element combustible nouveau, tant en ce qui concerne la gaine et eventuellement la chemise de graphite que le combustible lui-meme. Pour ce qui est de l'elaboration du combustible, ils decrivent les differentes operations en insistant sur les points originaux de la fabrication et de l'appareillage tels que: - coulees en moules chauds, - traitement thermique des alliages U.Mo 1 p. 100, - soudure des pastilles de fermeture des tubes, - gainage - controle aux differents stades. En ce qui concerne la fabrication des gaines, ils

  15. Nuclear analytical techniques in Cuban sugar industry

    International Nuclear Information System (INIS)

    Diaz R, O.; Griffith M, J.

    1997-01-01

    This paper is a review concerning the application of Nuclear Analytical Techniques in the Cuban sugar industry. The most complete elemental composition of final molasses (34 elements) and natural zeolites (38) this last one employed as an auxiliary agent in sugar technological processe4s has been performed by means of instrumental Neutron Activation Analysis (INAA) and X-Ray Fluorescence Analysis (XRFA). The trace elemental sugar cane soill-plant relationship and elemental composition of different types of Cuban sugar (raw, blanco-directo and refine) were also studied. As a result, valuable information referred to the possibilities of using these products in animal and human foodstuff so as in the other applications are given. (author). 34 refs., 6 figs., 1 tab

  16. Confocal fluorescence techniques in industrial application

    Science.gov (United States)

    Eggeling, Christian; Gall, Karsten; Palo, Kaupo; Kask, Peet; Brand, Leif

    2003-06-01

    The FCS+plus family of evaluation tools for confocal fluorescence spectroscopy, which was developed during recent years, offers a comprehensive view to a series of fluorescence properties. Originating in fluorescence correlation spectroscopy (FCS) and using similar experimental equipment, a system of signal processing methods such as fluorescence intensity distribution analysis (FIDA) was created to analyze in detail the fluctuation behavior of fluorescent particles within a small area of detection. Giving simultaneous access to molecular parameters like concentration, translational and rotational diffusion, molecular brightness, and multicolor coincidence, this portfolio was enhanced by more traditional techniques of fluorescence lifetime as well as time-resolved anisotropy determination. The cornerstones of the FCS+plus methodology will be shortly described. The inhibition of a phosphatase enzyme activity gives a comprehensive industrial application that demonstrates FCS+plus' versatility and its potential for pharmaceutical drug discovery.

  17. Learning curve estimation techniques for nuclear industry

    International Nuclear Information System (INIS)

    Vaurio, Jussi K.

    1983-01-01

    Statistical techniques are developed to estimate the progress made by the nuclear industry in learning to prevent accidents. Learning curves are derived for accident occurrence rates based on actuarial data, predictions are made for the future, and compact analytical equations are obtained for the statistical accuracies of the estimates. Both maximum likelihood estimation and the method of moments are applied to obtain parameters for the learning models, and results are compared to each other and to earlier graphical and analytical results. An effective statistical test is also derived to assess the significance of trends. The models used associate learning directly to accidents, to the number of plants and to the cumulative number of operating years. Using as a data base nine core damage accidents in electricity-producing plants, it is estimated that the probability of a plant to have a serious flaw has decreased from 0.1 to 0.01 during the developmental phase of the nuclear industry. At the same time the frequency of accidents has decreased from 0.04 per reactor year to 0.0004 per reactor year

  18. Methanization of industrial liquid effluents; Methanisation des effluents industriels liquides

    Energy Technology Data Exchange (ETDEWEB)

    Frederic, S.; Lugardon, A. [Societe Naskeo Environnement, 92 - Levallois-Perret (France)

    2007-09-15

    In a first part, this work deals with the theoretical aspects of the methanization of the industrial effluents; the associated reactional processes are detailed. The second part presents the technological criteria for choosing the methanization process in terms of the characteristics of the effluent to be treated. Some of the methanization processes are presented with their respective advantages and disadvantages. At last, is described the implementation of an industrial methanization unit. The size and the main choices are detailed: the anaerobic reactor, the control, the valorization aspects of the biogas produced. Some examples of industrial developments illustrate the different used options. (O.M.)

  19. Apparatus for examination of irradiated fuel elements of industrial reactors at Marcoule; Appareillage d'examen des elements combustibles des piles industrielles de Marcoule

    Energy Technology Data Exchange (ETDEWEB)

    Pesenti, P; Wallet, Ph [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The authors describe a viewing and measurement cell for the slugs of Marcoule industrial reactors. This cell allows visual inspection, and photography of slugs. Length measurements are also made possible by horizontal motion of the slug both in translation and rotation. (author) [French] Les auteurs decrivent une cellule d'observation et de mesure des elements combustibles des piles industrielles de Marcoule. La cellule permet l'examen a vue, la photographie, la radioscopie et la radiographie des elements combustibles. Elle permet en outre la mesure de longueurs sur ces elements, ces derniers pouvant etre deplaces horizontalement en translation, et en rotation. (auteur)

  20. Les composés organiques volatils réduction des émissions de COV dans l'industrie

    CERN Document Server

    2013-01-01

    Cet ouvrage propose des solutions techniques et une méthodologie pour réduire les émissions de composés organiques volatils (COV) dans l’atmosphère. Il permet : • de connaître l’impact des COV sur l’environnement et sur la santé, ainsi que les réglementations applicables en France et en Europe ; • de choisir les solutions d’amélioration disponibles (prévention, réduction à la source par secteur industriel, technologies de traitement et méthodes de mesure) ; • d’obtenir les clés pour mett re en place une démarche de réduction des émissions de COV (les étapes et les accompagnements possibles) ; • d’observer des exemples réussis d’investissement dans l’industrie. Cet ouvrage est un outil de travail indispensable pour les entreprises concernées par cett e problématique. Il donne les éléments essentiels pour aborder sereinement une démarche de réduction des émissions de COV. Points forts : • Des données rassemblées par un réseau d’experts spécialisés dans...

  1. Industrial uses of radioelements in France; Utilisation industrielle des radioelements en France

    Energy Technology Data Exchange (ETDEWEB)

    Gueron, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    The birth of a nuclear industry has permitted the use of radioelements in an increasing number of domains. Currently, the majority of radioelements applications in industrial problematic are essentially on nondestructive control and on problems of static electricity, as well as in a least way for the use of the intense radiation sources, on agronomic problems, for hydrology or chemical analyses. In order to promote the industrial applications, The CEA took to this purpose several sets of decisions: 1 - institution of teachings and collaboration; 2 - encourage the constructors of devices; 3 - creation of a help service to the users. (M.B.) [French] La naissance d'une industrie nucleaire a permit l'emploi des radioelements dans un nombre croissant de domaines. Actuellement, la majorite des applications industrielles de radioelements porte essentielement sur le controle non destructif et les problemes d'electricite statique, ainsi que dans une moindre mesure l'utilisation des rayonnements intenses, les problemes agronomiques, les questions d'hydrologie, les analyses chimiques. Afin de promouvoir les applications industrielles, Le Commissariat a l'Energie Atomique a pris a cet effet plusieurs series de mesures: 1- institution d'enseignements et de collaboration; 2- encouragement aux constructeurs d'appareils; 3- creation d'un service de consultation aux usagers. (M.B.)

  2. L’EPURATION TERTIAIRE DES EAUX USEES DE L’INDUSTRIE DE LA CELLULOSE

    Directory of Open Access Journals (Sweden)

    Constantin STANCIU

    2010-05-01

    Full Text Available Les processus de fabrication de la cellulose représentent des sources importantes de pollution tant pour les eaux, que pour l’aire et le sol. La pollution de l’eau est du, essentiellement, aux substances organiques dissous, aux substances en suspension et aux substances colorantes. Les évacuations des substances polluantes résultant de l’industrie de la cellulose se classifient en : substances solides en suspension, composés avec une biodégradabilité rapide ou lente, sels anorganiques, composés toxiques et échangeurs de valeur de pH. On a analysé les substances filtrées résultant du processus de blanchiment de la cellulose pour l’industrie papetière fabriquée du bois des arbres à feuilles caduques (hêtre et l’efficacité de l’épuration par oxydation électrochimique, par oxydation à l’ozone, l’épuration avec des résines échangeuses d’ions et l’épuration par l’ajout de charbon actif.

  3. Evaluation technique des analyseurs de mesure de la qualité de l'air

    OpenAIRE

    Tatry , Véronique

    1996-01-01

    Les objectifs des évaluations techniques des analyseurs de mesure de la qualité de l'air sont : de vérifier les performances métrologiques de ces analyseurs, de connaître la capacité des appareils à travailler sur le terrain, d'évaluer la capacité du fournisseur à résoudre les problèmes techniques que pose l'exploitation de son appareil. Cette activité existe à l'INERIS depuis plus de 20 ans (ex CERCHAR et ex IRCHA). Elle s'appuie sur une procédure décrite dans la norme française NF X 20-300 ...

  4. The study of hard microporous material using the ultrafine section technique (1961); Etude des materiaux microporeux durs par la technique des coupes ultraminces (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Magdalena, Th [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    The conventional replica techniques for the examination of surfaces or fractures with the electron microscope are unsuitable for refractories or microporous bodies. The method of cutting ultrafine sections with a diamond cutter, the sample being impregnated with methyl methacrylate, has the advantage of making possible the direct examination by transmission of the sample. (author) [French] Les techniques classiques de repliques pour l'examen de surfaces ou de fractures au microscope electronique sont difficilement applicables aux refractaires et aux microporeux. Les coupes ultraminces au couteau de diamant d'echantillons enrobes dans le methyl-methacrylate ont l'avantage de permettre l'examen direct par transmission des corps etudies. (auteur)

  5. Revision of the law governing the energy industry; Neuregelung des Energierechts

    Energy Technology Data Exchange (ETDEWEB)

    Anon,

    1993-11-03

    In its report on measures for safeguarding the competitiveness of the German industry, the Federal Government announced a number of reforms covering among others a revision of the regulatory framework governing the electricity and gas industry. Major goals in this context are deregulation and an enhancement of competition. The Federal Ministry of Economics prepared a draft plan for action addressing the need for an amendment of the Energy Management Act and the Act Against Restraints on Competition. Implementation of the measures given in the draft plan would create completely new conditions for the pipeline energy supply industry. (orig./HSCH) [Deutsch] Die Bundesregierung hat in ihrem Bericht zur Zukunftssicherung des Wirtschaftsstandorts Deutschland auch die Reform des Ordnungsrahmens fuer Strom und Gas angekuendigt. Ziel dieser Reform sollen Wettbewerb und Deregulierung sein. Das Bundeswirtschaftsministerium hat dazu auf Fachebene ein Konzept erarbeitet, das ein neues Energiewirtschaftsgesetz sowie eine Aenderung des Gesetzes gegen Wettbewerbsbeschraenkungen umfasst. Das Konzept wuerde die leitungsgebundene Versorgungswirtschaft auf eine voellig neue Grundlage stellen. (orig./HSCH)

  6. Emissions control techniques applied to industrial vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Martin, B.

    2004-12-15

    As emission standards for industrial vehicles become increasingly stringent, many research projects are seeking to develop after-treatment systems. These systems will have to combine efficiency, durability and low operating cost.

  7. The Main Technological Characteristics of Apparatus for Industrial Radiochemical Processes, in Particular Ethylene Polymerization; Caracteristique techniques fondamentals des appareils pour l'application industrielle de reactions chimiques sous rayonnement (notamment la polymerisation de l'ethylene ); Osnovnye tekhnologicheskie kharakteristiki apparatov dlya provedeniya radiatsionno-khimi-cheskikh protsessov (v chastnosti, dlya polimerizatsii ehtilena) v promyshlennom masshtabe; Principales caracteristicas tecnologicas de los aparatos para la aplicacion industrial de reacciones radioquimicas

    Energy Technology Data Exchange (ETDEWEB)

    Syrkus, N P; Breger, A K; Weinstein, B I [Karpov Physicochemical Institute, Moscow, USSR (Russian Federation)

    1960-07-15

    The paper gives a general review of some of the main technological features of apparatus, for instance spherical apparatus, for industrial radiochemical processes. A method is proposed for estimating the effectiveness of apparatus of any given construction by comparing it with the output of an infinitely large apparatus having the same radiation source. An account is given of the technological features of an apparatus for radio-polymerizing ethylene at 200 atmospheres and 25{sup o}C{sup 1} with a rodshaped gamma-radiation source (Co{sup 60}) of variable activity. This apparatus can be designed to suit the mean dose rate which the power efficiency of the apparatus allows. It is shown that the yield, Q, of the apparatus is, other things being equal, a constant ration of the power, W{sub 0}, of the gamma-radiation of the apparatus. In the apparatus reviewed, Q {approx} W{sub 0}{sup 0,5}. (author) [French] Le memoire contient un expose general des caracteristiques techniques essentielles des appareils, par exemple d'un appareil du type spherique, pour l'application industrielle de reactions chimiques sous rayonnement. Le memoire propose une methode pour evaluer l'efficacite d'appareils de tous types en comparant la productivite de chaque modele avec celle d'un appareil infiniment grand, alimente par une source de rayonnement identique. Le memoire indique le calcul des caracteristiques techniques de l'appareil destine a la polymerisation sous rayonnement de l'ethylene (pression : 200 atmospheres, temperature: 25{sup o}C{sup 2} avec une source allongee de rayonnement gamma Co{sup 60} pour diverses activites. Un appareil de ce type peut etre calcule selon les valeurs moyennes de l'intensite des doses, determinees selon la valeur du coefficient d'efficacite totale energetique de l'appareil. On constate que la productivite (Q) de l'appareil, toutes choses egales d'ailleurs, est puissance de l'intensite (W{sub 0}) du rayonnement gamma de l'appareil. Pour l'appareil considere

  8. Constant exposure technique in industrial radiography

    International Nuclear Information System (INIS)

    Domanus, J.C.

    1983-08-01

    The principles and advantages of the constant exposure technique are explained. Choice of exposure factors is analyzed. Film, paper and intensifying screens used throughout the investigation and film and paper processing are described. Exposure technique and the use of image quality indicators are given. Methods of determining of radiographic image quality are presented. Conclusions about the use of constant exposure vs. constant kilovoltage technique are formulated. (author)

  9. Les industries culturelles en mutation : des modèles en question

    Directory of Open Access Journals (Sweden)

    Lucien Perticoz

    2012-09-01

    Full Text Available La présente contribution se propose de questionner la notion de modèles socio-économiques dans le cadre des travaux relatifs aux mutations des industries culturelles. À cette fin, l’exposé se déroulera en trois temps : nous reviendrons tout d’abord sur les caractéristiques essentielles des modèles génériques (modèle éditorial et de flot ainsi que sur leurs principaux apports ; nous expliquerons ensuite dans quelle mesure ils doivent être considérés, non comme une description fidèle de la réalité dont ils entendent rendre compte, mais davantage comme des règles du jeu permettant d’appréhender les mutations à l’œuvre ; enfin, à l’aune de la numérisation des contenus et de leur consommation via Internet, nous interrogerons l’hypothèse de l’émergence de nouveaux modèles génériques. En conclusion, nous insisterons sur la nécessité, à notre sens, de prendre en compte l’évolution des pratiques culturelles médiatiques en tant que dimension structurante de ces modèles.This paper aims to question the concept of socio-economic models within the framework of research about cultural industries mutations. For this purpose, our presentation will proceed in three parts : first of all, we will reconsider the essential characteristics of the generic models (publishing model and flow model and their main contributions to the research ; we will explain then why they must be considered, not as a faithful description of the reality of which they intend to give an account, but more like rules of the game allowing to understand the mutations of cultural industries ; finally, considering the digitalization of contents and their consumption using Internet, we will question the hypothesis of the emergence of new generic models. In conclusion, we will insist on the importance, from our opinion, to take into account the evolution of the media cultural practices as a structuring dimension of these models.

  10. Original Paper Evaluation des techniques de production du beurre ...

    African Journals Online (AJOL)

    The results obtained showed that 31.25% of production units were using the classic churning, followed by Fulani churning processes (25.00%) and direct cooking (25.00%). Industrial technology (UIP1 and UIP2: 06.25%) and churning without roasting (06.25%) are the least practices. Butter yields found are: 49.00% (UIP1); ...

  11. Technique de la membrane induite pour la reconstruction des pertes ...

    African Journals Online (AJOL)

    humérus par la technique de la membrane induite au moyen d'une fibula non vascularisée avec apport de substitut osseux complémentaire chez une adolescente de 14 ans. Un incident cicatriciel a été observé sur le site de prélèvement.

  12. The utilization of irradiation techniques in food industry

    International Nuclear Information System (INIS)

    Szabo, S.A.

    1988-01-01

    Irradiation technical researches and the main areas of nuclear technical applications are surveyed, and the main areas where nuclear techniques are used are reported. Then an overview on radiation techniques including radiostimulation, radiomutation, radurization, radioecology and isotope techniques used in the food industry is presented. (author) 4 refs

  13. Energy saving in industrial varnishing techniques

    International Nuclear Information System (INIS)

    Kirst, W.

    1978-01-01

    The search for more effective varnishing techniques and better varnish surfaces and the increasing consideration of environmental protection, energy and raw materials conservation have helped to promote electron beam hardening. Also the development of high-solid varnishes have brought about the following improvements: Better quality of the varnish surface, possible saving of one layer in multilayer coatings, reduced emission in the waste air of the spray booth, conservation of valuable raw materials and energy. (orig.) [de

  14. Techniques conventionelles et innovantes, et solvants alternatifs pour l’extraction des lipides de micro-organismes

    Directory of Open Access Journals (Sweden)

    Abert Vian Maryline

    2013-11-01

    Full Text Available Cette revue propose un panorama complet des connaissances actuelles sur les microorganismes sources de lipides utilisés comme biocarburant. Elle fournit les éléments nécessaires à la compréhension de la culture des microorganismes (micro-algues, levures, bactéries et champignons et de leur capacité à accumuler les lipides. Des techniques conventionnelles et innovantes ainsi que des solvants alternatifs pour extraire les lipides ont été détaillés.

  15. Radiation ionization is an underestimated industrial technique

    International Nuclear Information System (INIS)

    Anon.

    1999-01-01

    Industrial radiation ionization requires electron beams coming from an accelerator or gamma radiation from a radioactive source (Co 60 ). The energy deposed in the irradiated material modifies its chemical bounds or kills micro-organisms. This process is used in medical material sterilization, in disinfestation of stored and packaged food products, in the production of plastic, in the coloring of glass, in the hardening of electronic components and in the modification of the properties of semi-conductors. For 40 years radiation ionization has been investigated, UNO (United Nations Organization) and WHO (World Health Organisation) recommend it for food processing. With a growing rate of 15% per year for the last 15 years, radiation ionization is now widely used. More than 170 gamma irradiation facilities are operating throughout the world. (A.C.)

  16. Dimensional measuring techniques in the automotive and aircraft industry

    Science.gov (United States)

    Muench, K. H.; Baertlein, Hugh

    1994-03-01

    Optical tooling methods used in industry are rapidly being replaced by new electronic sensor techniques. The impact of new measuring technologies on the production process has caused major changes on the industrial shop floor as well as within industrial measurement systems. The paper deals with one particular industrial measuring system, the manual theodolite measuring system (TMS), within the aircraft and automobile industry. With TMS, setup, data capture, and data analysis are flexible enough to suit industry's demands regarding speed, accuracy, and mobility. Examples show the efficiency and the wide range of TMS applications. In cooperation with industry, the Video Theodolite System was developed. Its origin, functions, capabilities, and future plans are briefly described. With the VTS a major step has been realized in direction to vision systems for industrial applications.

  17. Installation of the ITER committee industry. Participants guide; Installation du Comite industrie ITER. Dossier des participants

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    ITER is an international project to design and build an experimental fusion reactor based on the tokamak concept. This guide presents the ITER project and objectives and the associated organizations in France, the recommendations and actions for ITER, the industrial mobilization, the industrial committee and its members, technological sheets for the enterprises and the statistical document of the SESSI. (A.L.B.)

  18. Application of tracer technique in cement industry

    International Nuclear Information System (INIS)

    Baran'ai, L.

    1979-01-01

    Application is stated of the radioisotope indication method in the cement industry. The method was applied in three directions. In the first direction, by means of labelling of 300 steel mill balls by cobalt-60, wear of them was examined. The degree of wear of milling balls in the process of milling was determined according to the decrease of their weight. Radioactive label served only for tracing controll balls. In the second direction, according to the natural radioactivity being presented in ashes by radioisotopes radium-226 and thorium-229, amount of ashes in the products of cement milling was determined (in the mill product, cement product, flying dust and back loading groats). In the third direction, by means of labelling of definite fractions of mille by radioisotope gold-198, optimization of technological parameters of silos were raw meal is homogenization. The following technological parameters have been established: amount of homogenized material; time of homogenization and frequency of intensity changing of supplied compressed air jet [ru

  19. Optical Measurement Techniques Innovations for Industry and the Life Sciences

    CERN Document Server

    Peiponen, Kai-Erik; Priezzhev, Alexander V

    2009-01-01

    Devoted to novel optical measurement techniques that are applied both in industry and life sciences, this book contributes a fresh perspective on the development of modern optical sensors. These sensors are often essential in detecting and controlling parameters that are important for both industrial and biomedical applications. The book provides easy access for beginners wishing to gain familiarity with the innovations of modern optics.

  20. LE SOLUTRÉEN ANCIEN EN ARDÈCHE (FRANCE: UNE RÉVISION CRITIQUE DES INDUSTRIES LITHIQUES

    Directory of Open Access Journals (Sweden)

    Sophie Guegan

    2013-11-01

    Full Text Available S’inscrivant dans un travail de Doctorat sur les peuplements des deux rives de la vallée du Rhône au Maximum Glaciaire, cet article propose un état des connaissances sur la phase ancienne du Solutréen en Ardèche (rive droite du Rhône, donnant lieu à une révision critique des industries lithiques s’y rapportant. En effet, depuis les travaux de P.E.L. Smith et J. Combier, et plus récemment le travail d’A. Barbiero consacré aux pointes à face plance et pointes à cran d’une collection ancienne à la Baume d’Oullins (Gard-Ardèche, France, aucun réexamen global n’avait été entrepris. Trois gisements de référence pour cette phase ancienne, ont ainsi été sélectionnés: les grottes d’Oullins (Gard-Ardèche, France, de Chabot (Gard, France et de Granouly (Ardèche, France. Nous présentons ici les réslutats préliminaires à cette étude. En premier lieu, une approche typologique a été menée principalement autour de la pointe à face plane, objet emblématique de cette phase, permettant d’en préciser les principaux caractères. Dans un deuxième temps, une approche technologique a permis de confirmer l’homogénéité dans les choix techniques des Solutréens entre l’Ardèche et les régions du Sud-Ouest et du Bassin Parisien. Enfin, une étude des matières premières, a révélé pour l’heure des choix économiques étonnants pour le contexte paléo-climatique, avec des déplacements vers le nords et un franchissement du Rhône.In the frame of a doctoral dissertation on the Late Glacial Maximum occupations of both sides of the Rhône valley, this paper presents a state of the art and a critical reappraisal of the lithic assemblages from the early phases of the Solutrean in Ardeche (right bank of the Rhône river. Indeed, since the works of P.E.L. Smith and J. Combier, except the work of A. Barbiero, on the unifacial leaf-points and shouldered points from Baume d'Oullins, no complete study of these

  1. Thin layer activation techniques in research and industry

    International Nuclear Information System (INIS)

    Conlon, T.W.

    1993-01-01

    The following key application of thin layer activation technique (TLA) are discussed: ion-erosion in fusion tokamaks, bio-engineering technology, automobile industry. Future developments of the techniques, such as fission fragment TLA, multi-layer TLA and recoil implantation are discussed as well. 7 refs, 6 figs, 1 tab

  2. Le jeu incertain des générations An uncertain play of generations. How rap artists settle as a professional group within the French music industry

    Directory of Open Access Journals (Sweden)

    Karim Hammou

    2011-11-01

    Full Text Available Le rap en français peut être aujourd’hui considéré comme un univers professionnel établi, tout en étant une innovation relativement récente. Cet article montre que sa pérennisation est le fruit des rapports complexes entre trois générations d’artistes, et entre ces générations et les acteurs des industries musicales. Il s’appuie en particulier sur l’examen des conventions discographiques (refrains, collaborations, producteurs… privilégiées par les rappeurs qui se succèdent en France de 1990 à 2004. Une première génération émerge en 1990-1993 d’un pari ponctuel des grandes maisons de disques sur le rap. Une nouvelle génération de rappeurs, celle de 1994-1997, ne bénéfice pas d’un même contexte. Les clivages internes qui la traversent, liés à la médiation des radios, éclipsent ses tentatives de distinction à l’égard de la première génération. Dans le jeu de rivalités et de collaborations entre ces fractions de la scène rap naît un système d’accréditation informelle entre rappeurs qui marginalise une frange de la deuxième génération. La pratique professionnelle du rap connaît alors une autonomie relative, descriptible comme une concession au sein de l’industrie du disque. Enfin, les artistes qui accèdent à la notoriété à partir de 1998 se distinguent par leur rapport d’aspirant à l’égard d’un monde social désormais perçu comme prévisible. L’étude d’un tel processus d’intégration d’une nouvelle technique d’interprétation vocale dans les industries musicales françaises révèle la pertinence de l’outil conceptuel des générations sociologiques pour saisir le renouvellement des univers artistiques et des dynamiques professionnelles.French rap music is now an established industry, although it is still a recent innovation. This paper shows that its establishment is the result of the complex relationship between three generations of artists, oligopolistic

  3. Radiation safety in industrial applications of nuclear techniques

    International Nuclear Information System (INIS)

    Lam, E.S.

    1981-01-01

    The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise. (author)

  4. Radiation safety in industrial applications of nuclear techniques

    Energy Technology Data Exchange (ETDEWEB)

    Lam, E S [Ministry of Health, Kuala Lumpur (Malaysia)

    1981-01-01

    The hazards associated with the use of industrial equipment is one of the undesirable by-products of advanced technology. The use of nuclear techniques is a good example. Due to the usefulness of such techniques, one may accept the risks involved if they can be brought down to manageable levels. Most of the nuclear techniques in use in industries in Malaysia require only minimal safety precautions as they make use of only small amounts of radioactive material. However, some large sources are also being used and safety precautions have to be strictly enforced. The management plays a critical role in these industries. The requirements for radiation safety include the monitoring of workers and work areas, the medical surveillance of workers and the provision of barriers and other safety precautions. The management should also look to the training of the workers and be prepared for any emergencies that may arise.

  5. Hacking interdit découvrez les techniques des hackers pour mieux vous protéger

    CERN Document Server

    Gomez-Urbina, Alexandre

    2010-01-01

    Aujourd'hui, impossible de surfer sur Internet sans protection efficace ! Mais même avec des logiciels appropriés, nul n'est à l'abri du danger ! Virus, usurpations d'adresse IP, troyens, intrusions dans votre système, attaques par phishing : l'imagination des pirates est sans limite ! La seule solution est de vous protéger efficacement et pour cela, un moyen : connaître les techniques des hackers pour mieux déjouer leurs pièges ! Un internaute averti en vaut deux !

  6. MUP, CEC-DES, STRADE. Codes for uncertainty propagation, experimental design and stratified random sampling techniques

    International Nuclear Information System (INIS)

    Amendola, A.; Astolfi, M.; Lisanti, B.

    1983-01-01

    The report describes the how-to-use of the codes: MUP (Monte Carlo Uncertainty Propagation) for uncertainty analysis by Monte Carlo simulation, including correlation analysis, extreme value identification and study of selected ranges of the variable space; CEC-DES (Central Composite Design) for building experimental matrices according to the requirements of Central Composite and Factorial Experimental Designs; and, STRADE (Stratified Random Design) for experimental designs based on the Latin Hypercube Sampling Techniques. Application fields, of the codes are probabilistic risk assessment, experimental design, sensitivity analysis and system identification problems

  7. Caractérisation des techniques de séchage du cacao dans les ...

    African Journals Online (AJOL)

    SARAH

    25 avr. 2013 ... RÉSUMÉ. Objectifs: Le séchage constitue une étape très importante dans la préparation du cacao marchand. Cette étude vise à caractériser les techniques utilisées par les producteurs en Côte d'Ivoire et déterminer leur influence sur la qualité des fèves. Méthodologie et résultats: Une enquête a été ...

  8. Etat actuel et avenir de l'industrie pétrolière d'extraction. Exposés présentés lors de la journée d'ouverture et la séance de clôture du Colloque international sur les Techniques d'Exploration et d'Exploitation des Hydrocarbures. Paris, 10-12 décembre 1975 Present State and Future of the Petroleum Extraction Industry. Talk Presented During the Opening Day and the Closing Session of the International Symposium on Hydrocarbon Exploration, Drilling and Production Techniques. Paris, 10-12 December 1975

    Directory of Open Access Journals (Sweden)

    Piketti G.

    2006-11-01

    Full Text Available Ce document reprend les exposés et les discussions qui ont suivi, présentés lors de la journée d'ouverture et la séance de clôture du Colloque International sur les Techniques d'Exploration et d'Exploitation des Hydrocarbures organisé à Paris du 10 au 12 décembre 1975 par l'Association de Recherche sur les Techniques d'Exploitation du Pétrole (ARTEP et le Comité d'Études Pétrolières Marines (CEPM. Les communications techniques de ce colloque ont été publiées dans deux ouvrages(' consacrés respectivement - à l'exploitation des gisements. Méthodes de récupération assistée. Techniques de production ; - et au forage et à la production en mers profondes. This article contains the talks and ensuing discussions presented during the opening day and the closing session of the International Symposium on Hydrocarbon Exploration, Drilling and Production Techniques organized in Paris from 10 ta 12 December 1975 by the Association de Recherche sur les Techniques d'Exploitation du Pétrole (ARTEP and the Comité d'Études Pétrolières Marines (CEPM. The technical papers presented at this symposium have been published in two volumes (2 on the following respective topics - Reservoir Engineering. Enhanced Recovery Methods. Production Techniques; - Drilling and Production in Deep Water.

  9. Essences végétales et techniques de restauration des zones d'érosion

    African Journals Online (AJOL)

    SARAH

    30 sept. 2013 ... Objectif : Cette étude examine les meilleures espèces végétales et les techniques d'aménagement ... l'élaboration de stratégies durables de restauration des zones soudano-sahéliennes dégradées. ..... naturelle globale de 4,4% soit 12 plants et une mortalité .... des espèces et aux conditions climatiques.

  10. Régler le cas des rejets miniers qui polluent l'environnement | CRDI ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    sensibiliser les gouvernements, l'industrie et les citoyens aux effets néfastes des rejets miniers sur l'environnement et sur la santé des collectivités locales;; mettre au point des méthodes efficaces pour lutter contre la pollution engendrée par les rejets miniers; établir des techniques de remise en état des sites d'exploitation ...

  11. L'impact des développements scientifiques sur la résolution des problèmes techniques posés par la nouvelle conjoncture dans l'exploration et la production du pétrole Impact of Scientific Developments on the Solving of Technical Problems Raised by the New Economic Situation in Oil Exploration and Production

    Directory of Open Access Journals (Sweden)

    Tissot B.

    2006-11-01

    Full Text Available Dans les circonstances difficiles que traverse l'exploration et la production du pétrole, le savoir-faire technologique, associé à la maîtrise des coûts, seront pour l'industrie pétrolière et parapétrolière des atouts essentiels. On envisage ici l'impact prévisible des développements scientifiques sur la résolution des problèmes techniques dans l'exploration et la production. Les principales disciplines scientifiques concernées (géologie, géophysique, géochimie, mécanique des roches et des sols, mécanique des fluides, physicochimie des interfaces ainsi que trois techniques de base (modélisation, systèmes experts, matériaux nouveaux sont examinées dans ce sens. En particulier,la modélisation numérique voit son importance croître de manière spectaculaire : elle couvre désormais des domaines nouveaux, comme les Sciences de la Terre, et continue à s'enrichir de développements importants, même dans les secteurs où on l'utilise depuis 20 ans comme la production. Ces évolutions s'accompagneront nécessairement d'ajustements dans la formation des hommes et le fonctionnement des organisations; en particulier un espace nouveau pourrait se dégager pour de petites entreprises de conseil et de service plus riches en matière grise qu'en investissements lourds. In the difficult circumstances now confronting oil exploration and production, technical know-how combined with cost control will be essential assets for the petroleum and petroleum equipment and service industries. This article considers the foreseeable impact of scientific developments on the solving of technical problems in exploration and production. The principal scientific disciplines involved (geology, geophysics, geochemistry, rock and soil mechanics, fluid mechanics, interface physicochemistry as well as three basic techniques (modeling, expert systems, new materials are examined within this context. In particular, numerical modeling is increasing in

  12. Economic aspects of electricity and industrial heat generating reactors; Aspect economique des reacteurs produisant de l'electricite et de la chaleur industrielle

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J; Moulle, N; Dutheil, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Aldebert, J [Institut National des Sciences et Techniques Nucleaires (INSTN), CEA Saclay, 91 - Gif sur Yvette (France)

    1964-07-01

    The economic advantage of electricity-generating nuclear stations decreases when their size decreases. However, when a counter-pressure turbine is joined on to a reactor and the residual heat can be properly used, it can be shown that fairly low capacity nuclear equipment may compete with conventional equipment under certain realistic enough conditions. The aim of this paper is to define these special conditions under which nuclear energy can be profitable. They are connected with the location and the general economic environment of the station, the pattern of the electricity and heat demands it must meet, the level of fuel and specific capital costs, nuclear and conventional. These conditions entail certain technical and economic specifications for the reactors used in this way otherwise they are unlikely to be competitive. In addition, these results are referred to the potential steam and electricity market, which leads us to examine certain uses for the heat generated by double purpose power stations; for example, to supply combined industrial plants, various types of town heating and for removal of salt from sea water. (authors) [French] L'interet economique de centrales nucleaires productrices d'electricite decroit lorsque la puissance decroit. Cependant, lorsqu'on associe une turbine a contrepression a un reacteur et qu'il est possible d'utiliser dans de bonnes conditions la chaleur residuelle, on peut montrer que dans certaines conditions assez realistes, des equipements nucleaires d'une puissance unitaire peu elevee peuvent etre competitifs avec des equipements conventionnels. Cette communication a donc pour but de mettre en evidence quelles sont ces conditions particulieres de rentabilite de l'energie nucleaire. Elles sont liees a la localisation de la centrale et a son contexte economique general, a la structure de la demande d'energie electrique et thermique a laquelle elle doit satisfaire, au niveau des couts des combustibles et des investissements

  13. Economic aspects of electricity and industrial heat generating reactors; Aspect economique des reacteurs produisant de l'electricite et de la chaleur industrielle

    Energy Technology Data Exchange (ETDEWEB)

    Gaussens, J.; Moulle, N.; Dutheil, F. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Aldebert, J. [Institut National des Sciences et Techniques Nucleaires (INSTN), CEA Saclay, 91 - Gif sur Yvette (France)

    1964-07-01

    The economic advantage of electricity-generating nuclear stations decreases when their size decreases. However, when a counter-pressure turbine is joined on to a reactor and the residual heat can be properly used, it can be shown that fairly low capacity nuclear equipment may compete with conventional equipment under certain realistic enough conditions. The aim of this paper is to define these special conditions under which nuclear energy can be profitable. They are connected with the location and the general economic environment of the station, the pattern of the electricity and heat demands it must meet, the level of fuel and specific capital costs, nuclear and conventional. These conditions entail certain technical and economic specifications for the reactors used in this way otherwise they are unlikely to be competitive. In addition, these results are referred to the potential steam and electricity market, which leads us to examine certain uses for the heat generated by double purpose power stations; for example, to supply combined industrial plants, various types of town heating and for removal of salt from sea water. (authors) [French] L'interet economique de centrales nucleaires productrices d'electricite decroit lorsque la puissance decroit. Cependant, lorsqu'on associe une turbine a contrepression a un reacteur et qu'il est possible d'utiliser dans de bonnes conditions la chaleur residuelle, on peut montrer que dans certaines conditions assez realistes, des equipements nucleaires d'une puissance unitaire peu elevee peuvent etre competitifs avec des equipements conventionnels. Cette communication a donc pour but de mettre en evidence quelles sont ces conditions particulieres de rentabilite de l'energie nucleaire. Elles sont liees a la localisation de la centrale et a son contexte economique general, a la structure de la demande d'energie electrique et thermique a laquelle elle doit satisfaire, au niveau des couts des

  14. Technical and Economic Problems Associated with the Development of Methods of Processing and Using Radioactive Waste; Problemes techniques et economiques lies au developpement des methodes de traitement et d'utilisation des dechets radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    Thiriet, L; Sauteron, J; Oger, C [Commissariat a l' Energie Atomique, Fontenay-Aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    The paper briefly reviews the various techniques used in processing the radioactive wastes which unavoidably result from the generation of electric power from nuclear sources. The paper goes on to define the relative importance, in nuclear fuel cycles, of the problem raised by these wastes. Emphasis is placed on the economic influence of management policies on the cost of power generation, and hence on the relative position of nuclear energy. A substantial percentage of these wastes can be economically utilized. Attention is drawn to the major technical and economic features of the industry which will come into being as a result of this utilization. The major uses anticipated are discussed: radiation sources, heat sources, auxiliary power generation. The paper concludes that satisfactory solutions have already been found to these problems, and describes possible improvements. (author) [French] La communication rappelle d'abord succinctement les differentes techniques de traitement des dechets radioactifs resultant necessairement de la production d'electricite d'origine nucleaire. On situe ensuite l'importance du probleme pose par ces residus dans le cycle du combustible nucleaire. On fait ressortir l'influence economique du choix des methodes de gestion sur le cout de production de l'energie, et par consequent sur la place devolue a l'energie nucleaire. Une part importante de ces dechets peut faire l'objet d'une utilisation rentable de l'industrie qui naitra de cette utilisation. Les principales applications envisagees sont evoquees: sources d'irradiation, sources chauffantes, generateurs auxiliaires d'energie. On conclut que d'ores et deja des solutions satisfaisantes ont ete apportees a ces problemes, et l'on decrit les perspectives d'amelioration concevables. (auteur)

  15. Spécification géométrique des produits (GPS) -- Indication des états de surface dans la documentation technique de produits

    CERN Document Server

    International Organization for Standardization. Geneva

    2002-01-01

    La présente Norme internationale spécifie les règles pour l'indication des états de surface dans la documentation technique de produits (par exemple dessins, spécifications, contrats, rapports) au moyen de symboles graphiques et d'indications textuelles. Elle est applicable à l'indication des exigences sur les surfaces au moyen de paramètres de profil conformément à l'ISO 4287, relatifs au profil R (paramètres de rugosité), au profil W (paramètres d'ondulation) et au profil P (paramètres de structure), de paramètres liés aux motifs conformément à l'ISO 12085, relatifs au motif de rugosité et au motif d'ondulation, et de paramètres relatifs à la courbe du taux de longueur portante conformément à l'ISO 13565-2 et à l'ISO 13565-3. NOTE Quant à l'indication des exigences concernant les imperfections de surface (pores, stries, etc.), qui ne peuvent pas être spécifiées à l'aide des paramètres d'état de surface, référence est faite à l'ISO 8785 qui couvre les imperfections de surface...

  16. Application des techniques de diffusion de la lumière des rayons x et des neutrons à l'étude des systèmes colloïdaux. Deuxième partie : étude des différents systèmes : polymères en solution à l'état solide, solutions micellaires, systèmes fractals Application of Light, X-Ray and Neutron Diffusion Techniques to the Study of Colloidal Systems. Part Two: Research on Different Systems: Polymers in Solution in the Solid State, Micellar Solutions, Fractals Systems

    Directory of Open Access Journals (Sweden)

    Espinat D.

    2006-11-01

    Full Text Available Cet article fait suite à la première partie (Revue Inst. Franç. du Pétrole, vol. 45, n°6, novembre-décembre 1990 concernant l'application des techniques de diffusion de la lumière, des rayons X et des neutrons à l'étude des systèmes colloïdaux et plus précisément à la présentation théorique des trois méthodes. L'objet de cette deuxième partie est la présentation non exhaustive de quelques domaines d'applications. Nous nous attacherons tout particulièrement à présenter les potentialités des méthodes pour la caractérisation de systèmes colloïdaux ou divisés rencontrés dans de nombreuses branches d'activité de l'industrie pétrolière. Nous aborderons dans une première partie les solutions polymériques et colloïdales. En particulier nous nous attarderons sur l'importance des techniques de diffusion pour la caractérisation des polymères en solution et des solutions micellaires. Nous verrons également quelles informations la diffusion centrale peut apporter sur la macrostructure des polymères cristallisés ou amorphes à l'état solide. De nombreux systèmes présentent une structure de type fractal ; après présentation de quelques exemples, nous montrerons que les méthodes de diffusion peuvent apporter certaines informations sur ces matériaux, notamment la dimension fractale. This article is the second one (the first one was published in Revue de l'Institut Français du Pétrole No. 6, NovemberDecember 1990 concerning the application of techniques of light scattering, X rays and neutrons to the analysis of colloidal systems and more specifically to the theoretical description of the three methods. The aim of this second part is to make a nonexhaustive description of several fields of applications. A special effort is made to describe the potential of these methods for characterizing colloidal or divided systems encountered in a great many activities involving the petroleum industry. The first part of this

  17. Dictionary of nuclear sciences and techniques; Dictionnaire des sciences et techniques nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Bigot, B.; Santarini, G. [CEA Saclay (HC), 91 - Gif-sur-Yvette (France)

    2008-07-01

    This reference book has been totally reworked in its fourth edition, in order to answer the needs of the numerous sectors of activity concerned by nuclear sciences and technologies: radiation protection, cancerology, neurology and pharmacology in the medical sector, power generation and more generally energy production, micro-electronics, quality control and on-line analysis in many industrial sectors, patrimony preservation, food safety, environmental and paleo-climate studies in relation with climate prospective, etc. This complete overview of the nuclear world integrates the regulatory aspects, necessary to shade light on it, and many other technological innovations. Elaborated with harmonization, clarification and exhaustiveness concerns, this dictionary is the result of a large consensus among the French-speaking nuclear community. It includes some 4800 entries with more than 250 color illustrations and an English-French glossary. Its aim is to offer to everyone a precise vocabulary, fully shared by everybody and necessary for exchanges and debates clarity. (J.S.)

  18. Identification des risques professionnels dans l'industrie textile en République Démocratique du Congo

    Science.gov (United States)

    Kitronza, Panda Lukongo

    2014-01-01

    Introduction Le but de cette étude est de mettre en évidence les facteurs de risques professionnels liés aux conditions de travail. Méthodes Cette étude qualitative basée sur les entretiens de groupe a été réalisée par une équipe pluridisciplinaire dans l'industrie textile de la région du Est de la RDC; comprenant un médecin de travail, un médecin de santé publique, un toxicologue, deux infirmiers du centre hospitalier de l'usine, un représentant du comité d'hygiène et un technicien de prévention. La démarche méthodologique a consisté en des entretiens en groupe, des observations et visites guidées de lieux de travail de l'entreprise. Résultats Dans la culture du coton, les effets d'une forte exposition aux pesticides peuvent entraîner des intoxications aiguës, chroniques et voire le décès. Les autres risques sont les accidents de travail, les maladies professionnelles, les troubles psychologiques. Dans l'industrie, les travailleurs sont exposés aux risques liés à l'empoussiérage des fibres de coton, aux facteurs des risques traumatiques, physiques (bruits, vibration) et chimiques (acides forts, bases fortes, solvants et colorants minéraux), ainsi qu'aux risques psychosociaux. La pollution de l'environnement et l’écotoxicité inhérente à ces activités restent l'effet de l'usage des grandes quantités d'intrants agricoles, engrais et produits phytosanitaires. Conclusion Cette étude a permis de mettre en évidence les différents facteurs de risques auxquelles sont soumis les travailleurs textiles; ainsi que les risques environnementaux liés à cette activité. Cela est de nature à permettre la mise sur pied d'une stratégie efficace de prévention et de protection des travailleurs. PMID:25977736

  19. Les possibilités des turbines de détente dans les industries gazière et pétrolière Application of Expansion Turbines in the Gas and Oil Industry

    Directory of Open Access Journals (Sweden)

    Verneau A.

    2006-11-01

    Full Text Available Utilisées depuis longtemps dans l'industrie cryogénique, les turbines de détente voient leur intérêt augmenter actuellement en tant que turbines de récupération de l'énergie des laminages. Cette énergie peut servir à l'entraînement de compresseurs, pompes ou générateurs électriques. Il existe surtout des turbines dans la gamme de 200 à 20 000 ch. Deux types principaux sont développés : les turbines axiales et les turbines radiales. Les particularités techniques et les domaines d'emploi de chaque type sont discutés. Ue intérêt particulier est porté au domaine des petites puissances (de 100 kW jusqu'à quelques centaines de watts. L'évolution du rendement en fonction de la puissance est étudiée et quelques types spéciaux bien adaptés à cette gamme, tels que les turbines périphériques, sont présentés. Quelques indications sur la récupération de l'énergie des liquides par turbines sont également données. Ensuite, plusieurs exemples d'applications sont exposés tels que : récupération de fractions condensables du gaz naturel (butane, propane, éthane, récupération de gaz perdu, récupération de l'énergie des laminages lors de la distribution et au niveau des stockages souterrains, turbine hydraulique de lavage de gaz, récupération de l'énergie des fumées de cracking catalytique, entraînement de petits générateurs électriques dans la gamme de quelques kilowatts à quelques centaines de watts. Enfin, nous abordons la technologie et les dispositions constructives particulières en nous attachant plus spécialement aux problèmes de régulation, étanchéité, paliers. Des techniques nouvelles telles que l'emploi de paliers à gaz et leurs avantages sont décrites. Les difficultés dues aux basses températures et à la condensation sont examinées. Nous terminons par quelques considérations d'ordre économique destinées à prévoir la rentabilité d'une installation de récupération d

  20. Application of Nuclear Techniques in Industry and the Environment

    International Nuclear Information System (INIS)

    Masinza, A.S.

    2015-01-01

    Major radiotracer techniques are now in routine service industry to optimize processes, solve problems improve product quality, save energy and reduction pollution. The benefit to cost ratios of radiotracers, sealed sources and nucleonic gauges applications are considerably high; between 10:1 and 4000:1. The number of services for troubleshooting carried out worldwide per year is in excess of tens of thousands (out of them greater than 5000 are gamma scans). The number of nucleonic gauges worldwide could be estimated to be greater that 250,000 (Author)

  1. Applications of the automatic meter reading techniques at the Brazilian gas domestic market; Application des techniques de releve automatique des compteurs sur le marche domestique Bresilien du gaz

    Energy Technology Data Exchange (ETDEWEB)

    Venancio, J.; Monteiro, F. [Comgas, Sao Paulo (Brazil); D' Oliveira, R.D. [ORBIS, Curitiba (Brazil)

    2000-07-01

    This article will describe applications of the automation and automatic meter reading techniques at the internal gas pipes installations design, considering residential and commercial buildings, and taking in account the tendency of rapid growth of the activities related to the natural gas industry in Brazil, as well as the recently development of new technologies that can be applied with affordable prices. It will be analysed the application of an automatic meter reading technology in a building of several floors in Sao Paulo, which gas installations design is being carried up, with be purpose of making a comparative cost-effectiveness study with the traditional constructive methods applied in Brazil. As a result, it will be purposed a new commercialization model for the gas in Brazil at the residential and commercial market. (authors)

  2. Multiple-energy Techniques in Industrial Computerized Tomography

    Science.gov (United States)

    Schneberk, D.; Martz, H.; Azevedo, S.

    1990-08-01

    Considerable effort is being applied to develop multiple-energy industrial CT techniques for materials characterization. Multiple-energy CT can provide reliable estimates of effective Z (Z{sub eff}), weight fraction, and rigorous calculations of absolute density, all at the spatial resolution of the scanner. Currently, a wide variety of techniques exist for CT scanners, but each has certain problems and limitations. Ultimately, the best multi-energy CT technique would combine the qualities of accuracy, reliability, and wide range of application, and would require the smallest number of additional measurements. We have developed techniques for calculating material properties of industrial objects that differ somewhat from currently used methods. In this paper, we present our methods for calculating Z{sub eff}, weight fraction, and density. We begin with the simplest case -- methods for multiple-energy CT using isotopic sources -- and proceed to multiple-energy work with x-ray machine sources. The methods discussed here are illustrated on CT scans of PBX-9502 high explosives, a lexan-aluminum phantom, and a cylinder of glass beads used in a preliminary study to determine if CT can resolve three phases: air, water, and a high-Z oil. In the CT project at LLNL, we have constructed several CT scanners of varying scanning geometries using {gamma}- and x-ray sources. In our research, we employed two of these scanners: pencil-beam CAT for CT data using isotopic sources and video-CAT equipped with an IRT micro-focal x-ray machine source.

  3. Étude économique des foyers domestiques par la technique d ...

    African Journals Online (AJOL)

    Les foyers font partie de la vie courante. Chaque ménage en utilise pour la cuisson de ses repas. Dans les pays en développement, la plupart des populations utilisent surtout des foyers à combustibles ligneux. Les effets négatifs sur l'environnement sont aujourd'hui bien connus : poches de désertification, érosion des sols, ...

  4. Guide du calcul en mécanique valider le comportement des systèmes techniques

    CERN Document Server

    Spenlé, Daniel

    2012-01-01

    Ce guide couvre l’essentiel des programmes de la Première STI2D aux sections de BTS pour les compétences liées à la mécanique. Pour prendre en compte les nouveautés pédagogiques, cette nouvelle édition évolue vers des systèmes « grand public » (robotique humanoïde, cycle trainer, power-ball…) ou des systèmes liés au développement durable(éolienne, scooter électrique…). Points forts - Un guide qui tient compte des orientations du nouveau programme de STI2D : - systèmes vibratoires ; - accéléromètres, effet gyroscopique ; - développement de l’énergétique. - Les disciplines Génie mécanique/Génie électrique sont décloisonnées: - introduction de dispositifs pluri-techniques ; - présentation d’interfaces liant la partie opérative à la partie commande ; - introduction de la conversion de l’énergie électrique en énergie mécanique et réciproquement, étude comportementale, point de fonctionnement, définition des grandeurs associées. - Le caractère expérimental, ...

  5. Management accounting techniques and corporate performance of manufacturing industries

    Directory of Open Access Journals (Sweden)

    Ardiansyah Rasyid

    2017-03-01

    Full Text Available This research is to investigate that some factors that affect the new adoption in management accounting techniques on the Indonesia manufacturing industries, specifically in Jakarta, Bogor, Depok, Tangerang and Bekasi regions. The research can give a clearer portrait of how some factors can significantly affect the adoption of management accounting techniques. The research used some questioners which were sent to respondents who work in manufacturing industries as a middle level management. The methods used to distribute the questioners to respondents were by door to door, by e-mail and by media telecommunication (what’s app or close relationship up to hundreds questioners. We obtained 45 respondents but we eliminated one respondent, because they are not suitable to the research requirements. The research model contains the two paths. The first path contains 7 variables that divided by six exogenous variables to affect one endogenous variable and the next path model is from the three variables, that are divided to the one mediating variable and the other one exogenous variables to affect one endogenous variable (like path modelling. The research result shows that high competition does not affect the new accounting adoption but the other five variables; cost system changing, technology changes, organization climate, consumer demand and size significantly affect the new accounting adoption. For the next path, the research finds that the new accounting adoption can significantly affect corporate performance and also corporate performance measurement perception.

  6. Risk analysis of industrial plants operation; Integration des evenements accidentels dans les bilans sur les nuisances industrielles

    Energy Technology Data Exchange (ETDEWEB)

    Hubert, Philippe

    1989-12-01

    This study examines the possibilities of systematic technology risk analysis in view of territorial management (city, urban community, region), including chronic and accidental risks. The objective was to relate this evaluation with those done for permanent water and air pollution. Risk management for pollution are done for a long time. A number of studies were done in urban communities and regions both for air and water pollution. The second objective is related to management of industrial risks: nuclear, petrochemical, transport of hazardous material, pipelines, etc. At the beginning, three possibilities of effects are taken into account: human health, economic aspect and water, and possibilities of evaluation are identified. Elements of risk identification are presented for quantification of results. [French] Cette etude examine les possibilites d'une analyse systematique du risque accidentel technologique dans une optique d'evaluation et de gestion territoriale (ville, communaute urbaine, region), qui integre: tous les types de risque chroniques et accidentels. Un des objectifs est donc d'articuler de telles evaluations avec celles qui sont faites pour les pollutions chroniques de l'eau et de l'air. La gestion du risque dans ces domaines se fait en effet selon une approche spatiale depuis longtemps: les deux exemples les plus nets sont les agences de bassin et les reseaux de surveillance et d'alerte pour la pollution de l'air. Parallelement a ces systemes de gestion, et souvent pour les besoins de leur fonctionnement, de nombreuses etudes ont ete effectuees sur des communautes urbaines et des regions, tant pour l'air que pour l'eau. L'autre objectif est de tirer parti des analyses faites sur les objets industriels, qui sont, a l'image de la gestion de leurs risques, sectorielles: industrie nucleaire, industrie petrochimique, transport de matieres dangereuses, pipeline etc.. Dans un premier temps, les trois angles d'attaque possibles du risque accidentel sont

  7. Effet des techniques de conservation des eaux et des sols, zaï forestier et cordons pierreux, sur la réhabilitation de la végétation herbacée à l'Ouest du Burkina Faso

    DEFF Research Database (Denmark)

    Yameogo, Jérôme T.; Hien, Mipro; Lykke, Anne Mette

    2011-01-01

    Dans la perspective de trouver des solutions pour remédier au problème de dégradation des ressources naturelles en milieu forestier, des techniques de conservation des eaux et des sols ont été appliquées dans la forêt classée de Kuinima, à l’Ouest du Burkina Faso. L’étude a consisté au suivi de l...... espaces aménagés. Ceci témoigne d’une restauration progressive de ces parcelles aménagées....

  8. 173 Étude des performances épuratoires de la technique du ...

    African Journals Online (AJOL)

    Afrique Sciences

    à la station d'épuration de la ville d'Errachidia - Maroc. Chaouki HAMID1*, Lahcen ELWATIK1, Youssef RAMCHOUN2, Rachid FATH-ALLAH3,. Abdelrhafour AYYACH3, Zhor FATHALLAH4, Azzeddine EL MIDAOUI3 et El Mahdi HBAIZ5. 1Equipe des substances naturelles, synthèse et dynamique moléculaire, Faculté des ...

  9. La régulation des industries culturelles à l’heure d’Internet et les enjeux pour la diversité culturelle: Le cas des quotas radiophoniques français

    Directory of Open Access Journals (Sweden)

    Alexandre Joux

    2016-06-01

    Full Text Available La convention sur la protection et la promotion de la diversité des expressions culturelles, adoptée à l’UNESCO en 2005, redonne à l’instance internationale sa légitimité pour traiter des sujets liés aux politiques culturelles nationales. Ceux-ci avaient été déportés vers l’OMC dans les années 1990 à l’occasion des débats sur l’exception culturelle. Dix ans après l’adoption de la Convention de 2005, le développement de plates-formes mondiales de distribution des biens et services culturels remet toutefois en question, non pas les politiques culturelles nationales que la convention a sanctuarisés, mais leur efficacité à l’heure d’Internet. Ces évolutions obligent à comprendre la diversité culturelle au prisme de l’analyse économique pour imaginer des formes nouvelles et internationales de régulation des flux des produits des industries culturelles, ce qu’a révélé le débat français sur le projet de modification, en 2015, des quotas radiophoniques. Les quotas et les contraintes de programmation qu’ils imposent, en ne s’appliquant pas aux plates-formes de streaming musical, pourraient en effet et paradoxalement fragiliser les acteurs régulés sur qui repose la politique de diversité, sauf à étendre aux acteurs non-médiatiques le principe des quotas.

  10. Industrial solid and liquid waste treatment processes; Les procedes de traitement des dechets industriels solides et liquides

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1995-11-01

    This catalogue gives information on 68 chemical, mechanical, magnetic, electrical, thermal, etc. techniques for the processing of solid, viscous and liquid, common or special, industrial wastes. The various processes are presented as files, which are easily retrievable through keywords, waste type or industry codes, processing types, distributors. Technologies, performances and applications of each techniques are presented, together with references and company contacts

  11. Development and industrial utilisation of rotor balancing techniques at EDF

    International Nuclear Information System (INIS)

    Fanton, J.P.; Rondelet, D.

    1997-01-01

    The object of this document is to present, on the one hand, the industrial practice that exists at EDF in the area of rotor balancing, and, on the other hand, some recent development works, also in this area. One describes in a first part, for different types of machines concerned, the tools of calculation used, the performances that are obtained, and the encountered problems. Considering developments, one reminds first the characteristics of the EQUILOP 3.0 software, then one describes the validation that has been realized for it under a new computer environment. Additional operational possibilities that would be foreseeable for a new version of this software are indicated. A study currently under way of a balancing process which makes use of active control techniques is briefly described. Perspectives open by the utilization of numerical models of the machines as deduced from a recent study are exposed, and illustrated by a very simple example. (authors)

  12. Applications of prospecting geochemical techniques to the search for and to the study of uranium deposits in metropolitan France; Applications des techniques geochimiques de prospection a la recherche et a l'etude des gites uraniferes en France metropolitaine

    Energy Technology Data Exchange (ETDEWEB)

    Grimbert, Arnold

    1957-07-01

    After having recalled facts which leaded the CEA to use new geochemical techniques for the prospecting of uranium deposits through sampling and analysis of soils and waters, the author describes the organisation and methods implemented for this prospecting activity: team composition for sampling and analysis, role of each engineer and technician in the prospecting stages (preliminary study, routine prospecting, result interpretation), sampling and analysis processes. He also reports campaigns of geochemical prospecting: study of the La Chapelle Largeau deposit (objectives, geological context, preliminary study, routine prospecting, study of geochemical anomalies), tactical research on Verneix indices (study of radioactivity anomaly discovered by radio-prospecting), strategical searches in a non prospected area in the South of Avallon. The author discusses the issues of efficiency and cost price of this geochemical prospecting technique in soils and in waters. Appendices present the equipment and operation modality for soil sampling, and for soil sample preparation, and principles, equipment and products for soil analysis and for water analysis [French] A la suite des resultats satisfaisants obtenus dans la recherche de methodes de dosage adaptees au cas de l'uranium, la Direction des Recherches Minieres du Commissariat a l'Energie atomique a decide, en decembre 1954, d'utiliser, conjointement avec les methodes classiques de prospection, les techniques geochimiques pour la recherche et l'etude des gites uraniferes. Ces applications pratiques ont ete confiees a une Section de Geochimie dont l'organisation, les moyens en personnel et en materiel, ainsi que les methodes de travail, font l'objet d'un expose detaille. Quelques exemples de prospection, en France metropolitaine, montrent la nature des problemes poses (etude d'un gisement connu, recherche tactique sur des indices, recherche strategique dans une region non prospectee), les methodes utilisees pour les

  13. Learning-curve estimation techniques for nuclear industry

    Energy Technology Data Exchange (ETDEWEB)

    Vaurio, J.K.

    1983-01-01

    Statistical techniques are developed to estimate the progress made by the nuclear industry in learning to prevent accidents. Learning curves are derived for accident occurrence rates based on acturial data, predictions are made for the future, and compact analytical equations are obtained for the statistical accuracies of the estimates. Both maximum likelihood estimation and the method of moments are applied to obtain parameters for the learning models, and results are compared to each other and to earlier graphical and analytical results. An effective statistical test is also derived to assess the significance of trends. The models used associate learning directly to accidents, to the number of plants and to the cumulative number of operating years. Using as a data base nine core damage accidents in electricity-producing plants, it is estimated that the probability of a plant to have a serious flaw has decreased from 0.1 to 0.01 during the developmental phase of the nuclear industry. At the same time the frequency of accidents has decreased from 0.04 per reactor year to 0.0004 per reactor year.

  14. Learning curve estimation techniques for the nuclear industry

    International Nuclear Information System (INIS)

    Vaurio, J.K.

    1983-01-01

    Statistical techniques are developed to estimate the progress made by the nuclear industry in learning to prevent accidents. Learning curves are derived for accident occurrence rates based on actuarial data, predictions are made for the future, and compact analytical equations are obtained for the statistical accuracies of the estimates. Both maximum likelihood estimation and the method of moments are applied to obtain parameters for the learning models, and results are compared to each other and to earlier graphical and analytical results. An effective statistical test is also derived to assess the significance of trends. The models used associate learning directly to accidents, to the number of plants and to the cumulative number of operating years. Using as a data base nine core damage accidents in electricity-producing plants, it is estimated that the probability of a plant to have a serious flaw has decreased from 0.1 to 0.01 during the developmental phase of the nuclear industry. At the same time the frequency of accidents has decreased from 0.04 per reactor year to 0.0004 per reactor year

  15. Learning-curve estimation techniques for nuclear industry

    International Nuclear Information System (INIS)

    Vaurio, J.K.

    1983-01-01

    Statistical techniques are developed to estimate the progress made by the nuclear industry in learning to prevent accidents. Learning curves are derived for accident occurrence rates based on acturial data, predictions are made for the future, and compact analytical equations are obtained for the statistical accuracies of the estimates. Both maximum likelihood estimation and the method of moments are applied to obtain parameters for the learning models, and results are compared to each other and to earlier graphical and analytical results. An effective statistical test is also derived to assess the significance of trends. The models used associate learning directly to accidents, to the number of plants and to the cumulative number of operating years. Using as a data base nine core damage accidents in electricity-producing plants, it is estimated that the probability of a plant to have a serious flaw has decreased from 0.1 to 0.01 during the developmental phase of the nuclear industry. At the same time the frequency of accidents has decreased from 0.04 per reactor year to 0.0004 per reactor year

  16. Applying advanced digital signal processing techniques in industrial radioisotopes applications

    International Nuclear Information System (INIS)

    Mahmoud, H.K.A.E.

    2012-01-01

    Radioisotopes can be used to obtain signals or images in order to recognize the information inside the industrial systems. The main problems of using these techniques are the difficulty of identification of the obtained signals or images and the requirement of skilled experts for the interpretation process of the output data of these applications. Now, the interpretation of the output data from these applications is performed mainly manually, depending heavily on the skills and the experience of trained operators. This process is time consuming and the results typically suffer from inconsistency and errors. The objective of the thesis is to apply the advanced digital signal processing techniques for improving the treatment and the interpretation of the output data from the different Industrial Radioisotopes Applications (IRA). This thesis focuses on two IRA; the Residence Time Distribution (RTD) measurement and the defect inspection of welded pipes using a gamma source (gamma radiography). In RTD measurement application, this thesis presents methods for signal pre-processing and modeling of the RTD signals. Simulation results have been presented for two case studies. The first case study is a laboratory experiment for measuring the RTD in a water flow rig. The second case study is an experiment for measuring the RTD in a phosphate production unit. The thesis proposes an approach for RTD signal identification in the presence of noise. In this approach, after signal processing, the Mel Frequency Cepstral Coefficients (MFCCs) and polynomial coefficients are extracted from the processed signal or from one of its transforms. The Discrete Wavelet Transform (DWT), Discrete Cosine Transform (DCT), and Discrete Sine Transform (DST) have been tested and compared for efficient feature extraction. Neural networks have been used for matching of the extracted features. Furthermore, the Power Density Spectrum (PDS) of the RTD signal has been also used instead of the discrete

  17. Metallurgy of platinoids. Studies of industrial cases; Metallurgie des platinoides. Etudes de cas industriels

    Energy Technology Data Exchange (ETDEWEB)

    Blazy, P. [Ecole Nationale Superieure de Geologie, 54 - Vandoeuvre les Nancy (France); Jdid, E. A. [Institut National Polytechnique de Lorraine (ENSG/INPL/CNRS UMR 7569), 54 Vandoeuvre les Nancy (France)

    2004-03-01

    The platinoids deposits, currently in exploitation, are often associated with dunitic and gabbroitic ultra-basic rocks containing copper, nickel and iron sulfides. The proportion of platinoids in these deposits is variable and requires generally an adaptation of the industrial processes for their recovery. Nevertheless, we can consider that the classical industrial way consists to treat the composite concentrates of copper-nickel-platinoids sulfides by melting/conversion operations following by hydrometallurgical operations of recovery of the basic metals Cu, Ni. These last ones concentrate the platinoids in leaching residues. In these residues, the platinoids are extracted and separated by hydrometallurgical ways including different techniques: dissolution, selective precipitation, distillation, solvent extraction, resins...The great variety of uses of platinoids makes their recycling difficult. The wastes are often too complex for being economically recycling. The environmental protection depends of the type of industry (metallurgical, chemical, mining). Some products present risks of fire and explosion. The toxicity often appears by superficial allergies and by serious troubles in case of ingestion of soluble salts. (O.M.)

  18. Lits fluidisés pour l'industrie chimique. Extrapolation et amélioration des catalyseurs. Première partie : Etudes et modèles. Enseignements issus des pilotes Fluidized Beds in Chemical Industry. Scale Up and Catalysts Improvement. First Part: Studies, Models, Learning from Pilot Plants

    Directory of Open Access Journals (Sweden)

    Botton R.

    2006-12-01

    Full Text Available Les unités de production en lits fluidisés catalytiques sont apparues vers 1942 dans l'industrie pétrolière et vers 1960 dans l'industrie chimique. On se limitera ici au problème de l'extrapolation des lits fluidisés catalytiques pour l'industrie chimique, qui exigent de très hautes performances (> 99 % de conversion. Leur mise au point a, dans le passé, nécessité l'exploitation sur des sites industriels de coûteux pilotes de 0,5 m de diamètre et de plus de 10 m de hauteur. Nous montrerons que ces pilotes peuvent être évités et que le passage direct du laboratoire à l'échelle industrielle est réalisable. Cette possibilité offre en plus une méthode simple pour améliorer les catalyseurs des unités industrielles. Elle ouvre aussi cette technique, très appréciée en production, aux produits de petits tonnages. La présentation de cet article sera faite en trois parties : - La première, présentée ci-après, expose les problèmes majeurs posés par l'extrapolation, puis résume les études effectuées. Les travaux d'extrapolation relatifs à deux procédés effectués avec des pilotes sont ensuite présentés, à titre d'exemples. De ces travaux sont déduites les performances que l'on peut espérer obtenir avec un réacteur catalytique à lit fluidisé, ainsi que les règles de tendances à suivre pour y parvenir. - La deuxième partie, intitulée Stratégie n'utilisant que des expériences de laboratoire , propose une stratégie expérimentale permettant d'obtenir en laboratoire les informations nécessaires pour passer directement à l'échelle industrielle avec des expériences suggérées en partie par les résultats exposés dans le premier article. Les relations expérimentales établies lors de ces études montrent que les propriétés d'un lit fluidisé ne dépendent (mis à part quelquefois le diamètre du réacteur que d'un paramètre appelé vitesse minimum de fluidisation de comportement . - La troisième partie

  19. Economic statistics for the mining and metallurgical industries: 1990. Statistique economique des industries extractives et metallurgiques annee 1990

    Energy Technology Data Exchange (ETDEWEB)

    Rzonzef, L.

    1991-01-01

    Provides economic statistics for the Belgian mining and metallurgical industries in 1990. The review is divided into 4 parts: the extractive industries (including an analysis of the coal market and mines, quarries and associated industries); coke and briquette making; metallurgy (i.e. blast furnaces, steel making, rolling mills and manpower and materials consumption in the steel industry); and the extraction of sand from the Belgian continental shelf. 17 tabs.

  20. Performance de deux techniques d'extraction des phénols ...

    African Journals Online (AJOL)

    Influence in vitro des composes phénoliques des jeunes feuilles du pécher. Prunus persica (1) Batsch, sur le puceron vert du pecher, Myzus persicae sulzer. Agronomie 8 (9) : 787-792. Bell J.N., Dixon R.A., Bailey J.A., Rowell P.M. &. Lamb C.J., 1984. Differential induction of chalcone synthase mRNA activity at the onset.

  1. Techniques et systèmes de renfort des structures en béton

    CERN Document Server

    Miranda-Vizuete, J

    2000-01-01

    Bien qu'appelé « pierre artificielle », le béton est un matériau vivant qui se modifie tout au long de sa vie utile. Il change car la structure dont il fait partie subit elle-même des changements. Ces changements proviennent soit de modifications ou de rénovations, soit d'une altération de sa capacité de support par un accroissement des charges. Dans la plupart des cas, ils nécessitent un renfort. Le renforcement d'une structure en béton consiste à améliorer les caractéristiques mécaniques des éléments qui la composent, de manière à ce qu'elle offre une meilleure solidité aussi bien en état de service qu'en état de résistances ultimes. Ce document présente les méthodes les plus utilisées dans le domaine de renfort des structures dont l'incorporation des profiles métalliques, l'augmentation de section structurelle et celle plus récente du renforcement à base d'adjonction de matériaux composites extérieurs.

  2. Industrial fouling: problem characterization, economic assessment, and review of prevention, mitigation, and accommodation techniques

    Energy Technology Data Exchange (ETDEWEB)

    Garrett-Price, B.A.; Smith, S.A.; Watts, R.L.

    1984-02-01

    A comprehensive overview of heat exchanger fouling in the manufacturing industries is provided. Specifically, this overview addresses: the characteristics of industrial fouling problems; the mitigation and accommodation techniques currently used by industry; and the types and magnitude of costs associated with industrial fouling. A detailed review of the fouling problems, costs and mitigation techniques is provided for the food, textile, pulp and paper, chemical, petroleum, cement, glass and primary metals industries.

  3. Advanced MRI techniques of the fetal brain; Zukunftsweisende MRT-Techniken des fetalen Gehirns

    Energy Technology Data Exchange (ETDEWEB)

    Schoepf, V.; Dittrich, E.; Berger-Kulemann, V.; Kasprian, G.; Kollndorfer, K.; Prayer, D. [Medizinische Universitaet Wien, Abteilung fuer Neuroradiologie und Muskuloskelettale Radiologie, Universitaetsklinik fuer Radiodiagnostik, Wien (Austria)

    2013-02-15

    Evaluation of the normal and pathological fetal brain. Magnetic resonance imaging (MRI). Advanced MRI of the fetal brain. Diffusion tensor imaging (DTI) is used in clinical practice, all other methods are used at a research level. Serving as standard methods in the future. Combined structural and functional data for all gestational ages will allow more specific insight into the developmental processes of the fetal brain. This gain of information will help provide a common understanding of complex spatial and temporal procedures of early morphological features and their impact on cognitive and sensory abilities. (orig.) [German] Evaluierung des gesunden bzw. pathologischen fetalen Gehirns. Die Magnetresonanztomographie. Zukunftsweisende Techniken in der MRT-Bildgebung des fetalen Gehirns. Die Diffusionstensorbildgebung (DTI) befindet sich bereits in der klinischen Anwendung, alle anderen Methoden sind bisher noch als experimentell zu werten. Auf dem Weg zur Etablierung als Standardverfahren. Eine kombinierte Verarbeitung funktioneller und struktureller Daten, modelliert fuer jede Schwangerschaftswoche, wird es zukuenftig ermoeglichen, anhand dieser fusionierten Informationen einen praezisen Einblick in den Entwicklungsprozess des Gehirns zu erlangen. Diese Erkenntnisse und Ergebnisse werden entscheidend zur Klaerung des zeitlichen Verlaufs und des komplexen Aufbaus frueher morphologischer Auffaelligkeiten beitragen sowie deren Einfluss auf kognitive und sensorische Faehigkeiten aufzeigen. (orig.)

  4. Application des techniques de diffusion de la lumière des rayons X et des neutrons à l'étude des systèmes colloïdaux. Première partie : Présentation théorique des trois techniques Application of Light, X-Ray and Neutron Diffusion Techniques to the Study of Colloidal Systems. Part One : Theoretical Description of Three Techniques

    Directory of Open Access Journals (Sweden)

    Espinat D.

    2006-11-01

    Full Text Available Les techniques de diffusion, des rayons X, des neutrons et de la lumière, jouent un rôle très important pour la compréhension des milieux colloïdaux. Peu d'articles de la littérature s'attachent à présenter conjointement les trois méthodes. Nous avons, dans la première partie de cet article, détaillé les principes théoriques en insistent tout particulièrement sur les spécificités de chacune. Après les rappels concernant la diffusion par les systèmes dilués, nous nous sommes intéressés aux systèmes concentrés pour lesquels les entités diffusantes sont en interaction. Les milieux dispersés montrent souvent une certaine polydispersité que l'on cherche à mesurer; les techniques de diffusion permettent cette mesure. Nous terminerons cette revue par une description des appareillages utilisés. La deuxième partie de cet article concernera une large illustration des possibilités de ces méthodes d'analyse à l'étude des systèmes colloïdaux, sur la base de travaux effectués à I'IFP (Institut Français du Pétrole ou dans de nombreux laboratoires de recherche extérieurs. This article aims to describe X-ray, neutron and light scattering techniques with emphasis on their specific nature and their scope of application. Indeed, whereas light diffusion has been used for a long time in research laboratories, in particular for characterizing polymers in solution, small angle X-ray scattering has been the subject of renewed interest in recent years. Neutron scattering, which is obviously more difficultly accessible, has proven to be extremely useful for studying various systems for which light and X-ray scattering remain relatively powerless. Whereas there is an abundant literature concerning various applications of the three methods, it should be noted that only a few articles have attempted to describe all three techniques at the same time. In this article we have tried to make up for this lack, and as such it was

  5. The Cassava Processing Industry in Brazil: Traditional Techniques ...

    African Journals Online (AJOL)

    The paper considers the evolution of cassava-based industrial production, processing and marketing in Brazil, in light of the great technological diversification to be found in Brazil. It discusses the private role of the small- and medium-scale food and related processing enterprises in the food industry, as they employ ...

  6. Compter les toits – Quand des techniques de télédétection ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    7 janv. 2013 ... Pour mesurer les répercussions de la croissance rapide des bidonvilles ... Société canadienne d'hypothèques et de logement a travaillé avec DW Angola ... c'est-à-dire reportées sur la surface de la Terre, par divers moyens.

  7. Study of superconductors with high critical temperature by using the vibrating blade technique: anelastic properties, vortices dynamics; Etude des supraconducteurs a haute temperature critique par la technique de la lame vibrante: - proprietes anelastiques, - dynamique des vortex

    Energy Technology Data Exchange (ETDEWEB)

    De Brion, Sophie

    1991-10-04

    This research thesis reports the application of the vibrating blade technique to the study of high critical temperature superconductors, first for the anelastic properties, and then for vortices dynamics. As far as the study of anelastic properties is concerned, the author reports the measurement of dissipation and of Young modulus, between 4 K and 300 K and at about 1 khz, in YbaCuO ceramics with various oxygen content. A detailed study of the tetragonal phase reveals the existence of a single relaxation process, the magnitude of which depends on the compound oxygen content and on its thermal treatment. In the second part, the author reports the measurement, under magnetic field and within a temperature range lower than the superconducting critical temperature, of a YbaCuO crystal with two different oxygen concentrations. At low temperature, the author studies the contribution of vortices trapped in an irreversible state. At high temperature, this contribution disappears and thus defines an irreversibility line beyond which vortices are in a reversible regime. This line is studied for different magnetic field orientations with respect to CuO planes. It is interpreted in terms of de-trapping thermally activated by vortices [French] La technique de la lame vibrante a ete appliquee a l'etude des supraconducteurs a haute temperature critique, pour leurs proprietes anelastiques d'abord, pour la dynamique des vortex ensuite. Dans la gamme de temperature 4 K - 300 K, nous avons mesure la dissipation et le module d'Young, a une frequence de 1 kHz environ, dans des ceramiques YBaCuO (phase 123) de differentes teneurs en oxygene (variant de O{sub 6} a O{sub 7}). Nous avons observe plusieurs pics de dissipation. Une etude detaillee de la phase tetragonale (de O{sub 6} a O{sub 6,4}) a mis en evidence un seul processus de relaxation, active thermiquement avec une energie de 0,1 eV et dont l'ampleur depend de la teneur en oxygene du compose et de son traitement thermique. Cette

  8. Use of glasses as industrial dosimeters; Utilisation des verres comme dosimetres industriels

    Energy Technology Data Exchange (ETDEWEB)

    Balestic, F. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires; Le Clerc, P.; Bonnaud, M. [Centre de Recherches des Glaceries de Saint-Gobain (France)

    1959-07-01

    Glasses have the property of colouring under the action of ionizing radiations. We endeavoured to specify the conditions under which the intensity of coloration can be used as a measure of the quantity of radiation to which the glass has been submitted. In the case of a glass loaded with cobalt, a study of the optical density at different wavelengths enabled us to find the factors governing the formation of coloured centres and their conservation in the glass. We give a set of calibrating curves for different values of these parameters (irradiation rate, irradiation temperature; fading time and fading temperature), enabling determination of radiation doses in the range from 10 000 to 1 000 000 rep from measured optical density. (author) [French] Les verres ont la propriete de se colorer sous l'action des rayonnements ionisants. Nous avons cherche a preciser les conditions dans lesquelles l'intensite de la coloration peut servir de mesure de la quantite du rayonnement auquel le verre a ete soumis. Dans le cas d'un verre charge au cobalt, l'etude de la densite optique a differentes longueurs d'onde a mis en evidence divers facteurs dont depend la formation des centres colores et leur conservation dans le verre. En prenant comme parametres ces divers facteurs (temperature d'irradiation, intensite d'irradiation, temperature de conservation et duree de conservation) nous avons etabli des courus d'etalonnage permettant la determination de doses entre 10 000 et 1 000 000 rep d'apres la densite optique observee. (auteur)

  9. Use of glasses as industrial dosimeters; Utilisation des verres comme dosimetres industriels

    Energy Technology Data Exchange (ETDEWEB)

    Balestic, F [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires; Le Clerc, P; Bonnaud, M [Centre de Recherches des Glaceries de Saint-Gobain (France)

    1959-07-01

    Glasses have the property of colouring under the action of ionizing radiations. We endeavoured to specify the conditions under which the intensity of coloration can be used as a measure of the quantity of radiation to which the glass has been submitted. In the case of a glass loaded with cobalt, a study of the optical density at different wavelengths enabled us to find the factors governing the formation of coloured centres and their conservation in the glass. We give a set of calibrating curves for different values of these parameters (irradiation rate, irradiation temperature; fading time and fading temperature), enabling determination of radiation doses in the range from 10 000 to 1 000 000 rep from measured optical density. (author) [French] Les verres ont la propriete de se colorer sous l'action des rayonnements ionisants. Nous avons cherche a preciser les conditions dans lesquelles l'intensite de la coloration peut servir de mesure de la quantite du rayonnement auquel le verre a ete soumis. Dans le cas d'un verre charge au cobalt, l'etude de la densite optique a differentes longueurs d'onde a mis en evidence divers facteurs dont depend la formation des centres colores et leur conservation dans le verre. En prenant comme parametres ces divers facteurs (temperature d'irradiation, intensite d'irradiation, temperature de conservation et duree de conservation) nous avons etabli des courus d'etalonnage permettant la determination de doses entre 10 000 et 1 000 000 rep d'apres la densite optique observee. (auteur)

  10. La Mise en Jeu des Objets Techniques sur les Scènes Théâtrales Contemporaines

    Directory of Open Access Journals (Sweden)

    Julie Valero

    2016-05-01

    Full Text Available Cet article porte sur l’usage par le comédien de l’objet technique en posant la question suivante: la prise en mains de celui-ci en scène est-elle initiatrice de nouvelles pratiques de jeu? L’objet technique est d’abord défini d’un point de vue général. Son statut est ensuite caractérisé par rapport au contexte théâtral: comment se différencie-t-il de n’importe quel autre objet scénique? Instrument de jeu pour l’acteur, il développe des habiletés de jeu particulières: le travail scénique du Wooster Group est donné en exemple. L’objet technique apparaît dès lors comme un prolongement instrumental pour le corps jouant de l’acteur: des expériences artistiques se situant dans cette perspective sont ensuite étudiées.

  11. The internationalization of the technological activities in the energy industries; L'internationalisation des activites technologiques dans les industries energetiques

    Energy Technology Data Exchange (ETDEWEB)

    Bourgeois, B [Institut d' Economie et de Politique de l' Energie - IEPE-CNRS/ Universite Pierre Mendes-France, 38 - Grenoble (France); Jacquier-Roux, V [Institut de Recherche Economique sur la Production et le Developpement -IREPD, 38 - Grenoble (France)

    2001-06-01

    This analysis of the technological internationalization factors is defined in five chapters. The first chapter deals with the evolutionist representation of the internationalization process of the technological activities of the firms. The chapter two is an historical synthesis from 1985 to 2000, of the industrial dynamics and of the technological strategies of the petroleum and electric power industries. The chapter three details the empirical method used to verify the hypothesis. Chapter four exposes the data analysis results of the patents of the sampled firms. The last chapter is devoted to the results interpretation. (A.L.B.)

  12. De la gestion patrimoniale des réseaux d’assainissement aux techniques alternatives de gestion des eaux pluviales, une nouvelle histoire à écrire pour la gestion intégrée des eaux urbaines

    Directory of Open Access Journals (Sweden)

    CHERQUI, Frédéric

    2016-09-01

    Full Text Available Le patrimoine des ouvrages alternatifs de gestion des eaux pluviales ne cesse de s’accroître depuis maintenant plusieurs décennies. Pour les collectivités, organiser le recensement et développer des méthodes pour optimiser le fonctionnement et l’exploitation sur le long terme de ces ouvrages devient donc une préoccupation majeure. À partir du retour d'expérience de la Métropole de Lyon et des connaissances issues de la gestion la patrimoniale des réseaux d’assainissement, cet article permet d'identifier les questions émergentes et d'apporter des premiers éléments de réponse pour la mise en œuvre de la gestion patrimoniale des ouvrages alternatifs de gestion des eaux pluviales.

  13. MRI of the temporomandibular joint. Technique, results, indications; Magnetresonanztomographie des Temporomandibulargelenkes: Untersuchungstechnik, Ergebnisse, Indikationsstellung

    Energy Technology Data Exchange (ETDEWEB)

    Vogl, T.J.; Abolmaali, N. [Frankfurt Univ. (Germany). Inst. fuer Diagnostische und Interventionelle Radiologie

    2001-11-01

    An optimized examination protocol for the MRI evaluation of the temporomandibular joint (TMJ) is presented. The MRI protocol is based on an optimized coil technology, sequence design, and a programmed examination protocol for diagnostics of the TMJ. Depending on the clinical findings, MRI provides an all-in-one diagnostic protocol for the diagnosis of degenerative, inflammatory and tumorous lesions of the TMJ. MRI using an optimized examination protocol should become the primary examination protocol for diseases of the TMJ. (orig.) [German] Vorstellung der optimierten Untersuchungstechnik zur magnetresonanztomographischen (MRT) Evaluation des Temporomandibulargelenkes (TMG) und Darstellung der Ergebnisse und Indikationsstellung. Es werden die Spulentechnik, das Sequenzdesign, die Schichtorientierung und der programmierte Untersuchungsablauf in Abhaengigkeit von der klinischen Fragestellung praesentiert. In Abhaengigkeit von der klinischen Symptomatik stellt die MRT das primaere bildgebende Verfahren zur Diagnostik und Therapiekontrolle degenerativer, entzuendlicher und tumoroeser Prozesse des TMG dar. In Einzelfaellen muessen ergaenzend weitere radiologische Techniken wie die Orthopantomographie, die direkte Arthrographie und die Computertomographie zum Einsatz kommen. Die optimierte MRT des TMG erfordert eine dedizierte Untersuchungstechnik sowie spezielle Kenntnisse in der Beurteilung der akquirierten Bilder. (orig.)

  14. Testing techniques in nuclear, petroleum and metallurgic industries

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    The nondestructive testing techniques by ultrasonic waves, eddy currents, acoustic emission used by Intercontrole (a CEA's affiliated firm in nuclear petrochemical, and engineering site measurements) are presented [fr

  15. The thin layer technique and its application to electron microscopy; La technique des couches minces et son application a la microscopie electronique

    Energy Technology Data Exchange (ETDEWEB)

    Ranc, G. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-10-15

    This work deals with the technique of thin layers obtained by evaporation under vacuum, in the thickness range extending from a few monoatomic layers to several hundred angstroms. The great theoretical and practical interest of these layers has, it is well known, given rise to many investigations from Faraday onwards. Within the necessarily restricted limits of this study, we shall approach the problem more particularly from the point of view of: - their production; - their use in electron microscopy. A critical appraisal is made, in the light of present-day knowledge, based on our personal experience and on an extensive bibliography which we have collected on the subject. (author) [French] Le present travail concerne la technique des couches minces obtenues par evaporation sous vide, dans le domaine d'epaisseur qui s'etend de quelques couches monoatomiques a plusieurs centaines d'angstroms. L'interet theorique et pratique considerable de ces couches a suscite, comme on sait, de nombreux travaux depuis Faraday. Dans le cadre necessairement restreint de cette these, nous aborderons plus particulierement le point de vue de: - leur obtention; - leur utilisation en microscopie electronique. Il s'agit d'une mise au point critique, a la lumiere des connaissances actuelles, appuyee sur notre experience personnelle et sur une importante bibliographie, qu'il nous a ete donne de reunir a ce sujet. (auteur)

  16. The thin layer technique and its application to electron microscopy; La technique des couches minces et son application a la microscopie electronique

    Energy Technology Data Exchange (ETDEWEB)

    Ranc, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-10-15

    This work deals with the technique of thin layers obtained by evaporation under vacuum, in the thickness range extending from a few monoatomic layers to several hundred angstroms. The great theoretical and practical interest of these layers has, it is well known, given rise to many investigations from Faraday onwards. Within the necessarily restricted limits of this study, we shall approach the problem more particularly from the point of view of: - their production; - their use in electron microscopy. A critical appraisal is made, in the light of present-day knowledge, based on our personal experience and on an extensive bibliography which we have collected on the subject. (author) [French] Le present travail concerne la technique des couches minces obtenues par evaporation sous vide, dans le domaine d'epaisseur qui s'etend de quelques couches monoatomiques a plusieurs centaines d'angstroms. L'interet theorique et pratique considerable de ces couches a suscite, comme on sait, de nombreux travaux depuis Faraday. Dans le cadre necessairement restreint de cette these, nous aborderons plus particulierement le point de vue de: - leur obtention; - leur utilisation en microscopie electronique. Il s'agit d'une mise au point critique, a la lumiere des connaissances actuelles, appuyee sur notre experience personnelle et sur une importante bibliographie, qu'il nous a ete donne de reunir a ce sujet. (auteur)

  17. La conclusion d'un accord franco-allemand dans l'industrie des colorants en 1940-1941 : rapports de force et formes juridiques

    OpenAIRE

    Joly , Hervé

    2005-01-01

    L'accord conclu en 1941 entre le conglomérat dominant l'industrie chimique allemande, l'IG Farben, et les principaux producteurs français réuni autour du groupe Kuhlmann dans le secteur des colorants artificiels constitue sous l'Occupation un cas unique. C'est la seule prise de contrôle, sous la forme d'une participation majoritaire dans une société commune dénommée Francolor, de l'ensemble d'une branche industrielle nationale, de la fabrication à la commercialisation, par des intérêts allema...

  18. Management Science/Industrial Engineering Techniques to Reduce Food Costs.

    Science.gov (United States)

    Greenberg, Murray

    This paper examines the contributions of Industrial Engineering and Management Science toward reduction in the cost of production and distribution of food. Food processing firms were requested to respond to a questionnaire which asked for examples of their use of various operations research tools and information on the number of operations…

  19. Industrial Applications of Enzymes: Recent Advances, Techniques, and Outlooks

    Directory of Open Access Journals (Sweden)

    Jordan Chapman

    2018-06-01

    Full Text Available Enzymes as industrial biocatalysts offer numerous advantages over traditional chemical processes with respect to sustainability and process efficiency. Enzyme catalysis has been scaled up for commercial processes in the pharmaceutical, food and beverage industries, although further enhancements in stability and biocatalyst functionality are required for optimal biocatalytic processes in the energy sector for biofuel production and in natural gas conversion. The technical barriers associated with the implementation of immobilized enzymes suggest that a multidisciplinary approach is necessary for the development of immobilized biocatalysts applicable in such industrial-scale processes. Specifically, the overlap of technical expertise in enzyme immobilization, protein and process engineering will define the next generation of immobilized biocatalysts and the successful scale-up of their induced processes. This review discusses how biocatalysis has been successfully deployed, how enzyme immobilization can improve industrial processes, as well as focuses on the analysis tools critical for the multi-scale implementation of enzyme immobilization for increased product yield at maximum market profitability and minimum logistical burden on the environment and user.

  20. Industrial wastes guide for Alsace; Guide des dechets de l`entreprise Alsace

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    This guide is aimed for industrial plant managers and gives comprehensive information on industrial waste management: effects of wastes on the environment (water, air, soil), waste processing limitations in Alsace, new regulations, taxes and incentives concerning waste processing in France, and references of national and regional (Alsace) administration and industrial agencies that are related with pollution abatement and control and waste management. The different types of wastes are reviewed, from papers to toxic solvents, with information given on volumes, processes, operators, processing equipment and equipment distributors

  1. Employing 3R Techniques in Managing Cement Industry Waste

    Directory of Open Access Journals (Sweden)

    Lamyaa Mohammed Dawood

    2018-01-01

    Full Text Available Waste management conserves human health, ownership, environment, and keeps valuable natural resources. Lean-green waste of an organization’s operations can be decreased through implementation 3R (Reduce, Reuse, and Recycling techniques by reduction of manufacturing system wastes. This research aims to integrate lean-green waste of the manufacturing system throughout employing 3R techniques and weighted properties method in order to manage waste. Al-Kufa cement plant is employed as a case study. Results are generated using Edraw Max Version 7 and Excel. Overall results show reduce technique of lean-green waste management has major contribution of 55 % and recycling technique has minor contribution 18 %. Defects waste has major integration of lean-green waste, while air emissions waste has minor integration of lean-green waste.

  2. The management of industrial wastes in hydrology; La gestion des dechets industriels en hydrologie

    Energy Technology Data Exchange (ETDEWEB)

    Elbaz-Seboun, V.

    1998-07-08

    The industrial wastes are made of different kind of wastes: the inert wastes, the banal wastes (municipal wastes), the special wastes containing noxious elements with respect to human health and environment, and the radioactive wastes. Each industry generates its own effluents (sludges from water treatment plants and leachates from rubbish dumps). The main water pollutions are due to the fermentescible organic matters, nitrates and heavy metals from the industrial waste waters. The aim of the public water agencies is to better protect the environment and to give help to the industrialists in the management of their wastes: reduction at the source, selective collection, valorization, transportation and processing. Non-valorizable wastes must be processed: physico-chemical and biological processing (bio-filtering, coagulation-flocculation, membranes and industrial gases), incineration (organic wastes), disposal in class 1 technical burial centres after stabilization (ultimate wastes). Since July 2002, only the ultimate wastes will be disposed off and all class 2 and 3 dumps must have been rehabilitated. This work is divided into 2 parts: part 1 gives a presentation of the different types of industrial wastes and of their management (origin of wastes, effluents, heavy metals, environmental impact, legal aspects, wastes management, valorization). The second part describes the different processes for the treatment of industrial wastes (conventional processes, physico-chemical and biological processes, incineration, tipping, processing of radioactive wastes). (J.S.)

  3. Treatment of Some Hazardous Industrial Pollutants by Simple Oxidation Techniques

    International Nuclear Information System (INIS)

    Abd El-Rahman, N.M.

    1999-01-01

    Central treatment of Industrial wastewater requires pretreatment of some specific pollutants which may be not effectively degraded in down stream processes in central treatment unit. Some of the hazardous pollutants in industrial wastewater including acrylonitrile, pesticides and some commonly used dyes (active and acid dyes) have been subjected individually to oxidation using hydrogen peroxide catalyzed by ferrous ions in acidic solution. Treatment efficiency was monitored by chemical oxygen demand (COD) removal using a specially developed concentration/COD curves. Initial concentrations (in terms of COD) were 910 PPM, 1348 and 530 ppm and the respective COD reductions were 91, 98 and 99%, for the pesticide, acrylonitrile and the reactive dye. Oxidative degradation of polared and acid green also reduced COD by 99 and 100% respectively. The obtained results confirm the appropriateness of oxidative degradation as a pretreatment for some hazardous pollutants prior to treatment in central facilities or municipal activated sludge stations

  4. Radon space techniques for the evaluation of industrial tomography systems

    International Nuclear Information System (INIS)

    Burge, R.E.; Wombell, R.J.; Belchamber, R.M.; Betteridge, D.; Lilley, T.

    1987-01-01

    Computerised tomography (CT) is a powerful tool in medicine, and would be well suited to a wide range of industrial applications, particularly non-destructive testing. However, the very diversity of uses makes the production of a standardised scanner impossible. Systems for an industrial use will have to be designed with a problem in mind. An approach is presented for the analysis of CT scanning systems to help in the design problem. It first describes a system in terms of the sampling of the Radon transform of the object and then uses this information to produce a spatial description of the performance of a scanning system in terms of data collection. This description is called a resolution map and it is shown how the resolution map can be related to the object under study. (author)

  5. Gas Well Testing Analysis Using Finite-Difference Models and Optimization Techniques Analyse d'essais de puits de gaz par des modèles utilisant la méthode des différences finies et par des techniques d'optimisation

    Directory of Open Access Journals (Sweden)

    Darderes E. A.

    2006-11-01

    paramètres à partir d'essais de puits de gaz. Une des plus performantes est l'analyse du régime pseudo-permanent pour lequel on trouve, sur un graphique semi-logarithmique, une relation linéaire entre la pseudo-pression d'un gaz réel et le temps. Une autre méthode est l'ajustement à des courbes types. Les deux méthodes présentent l'inconvénient de ne pouvoir être rigoureusement appliquées qu'à des cas spécifiques. Cet article expose une méthode générale permettant d'analyser les données des essais de puits par ajustement automatisé des courbes types. Elle est basée sur le meilleur accord d'un modèle numérique avec les données obtenues dans les essais de puits de gaz grâce à des techniques d'optimisation. Le modèle numérique fournit la solution d'une équation différentielle à dérivées partielles du 2e ordre et fortement non linéaire qui régit le flux radial des gaz réels vers un puits de production. L'équation différentielle est résolue par la méthode des différences finies en tenant compte des variations des propriétés des gaz avec la pression. Pour simuler n'importe quel type d'essais de puits de gaz, on impose des conditions initiales et aux limites appropriées. On minimise les différences résiduelles entre les pressions réelles mesurées pendant l'essai et les pressions calculées par la méthode des moindres carrés. On utilise deux techniques d'optimisation pour obtenir la meilleure estimation des paramètres qui minimisent la somme des carrés des résidus : la méthode monovariante de Fibonacci [1] et la méthode polyvariante de Marquardt [1, 2]. On applique ce mode opératoire à des essais de puits menés à un débit constant et à deux débits constants. Les résultats numériques concordent très bien avec les données des essais de puits.

  6. Water saving techniques in the spanish tile industry

    Directory of Open Access Journals (Sweden)

    Enrique, J. E.

    2000-02-01

    Full Text Available A study was conducted on the use of water in the ceramic tile manufacturing process, focussing on water requirements in body and glaze preparation and in washing production equipment and facilities. Water consumption and wastewater reuse systems in ceramic tile manufacture were reviewed. An in-depth, industrial scale study was performed of wastewater reuse in the manufacturing process, examining how wastewater reuse affected pollutant contents in gas emissions and solid waste.

    Se ha estudiado el uso del agua en el proceso de fabricación de baldosas cerámicas y en particular, en las etapas de preparación de la pasta de los esmaltes y limpieza del equipo industrial y de la propia planta.Se ha realizado una revisión del consumo de agua y de los sistemas de reutilización de la misma en el proceso de fabricación de baldosas cerámicas y se ha estudiado con profundidad, a escala industrial, la reutilización del agua residual en el proceso y en particular el efecto de su reutilización sobre la emisión de contaminantes en las emisiones gaseosas y en los residuos sólidos.

  7. Industrial radiation and radioisotope gauging techniques and applications

    International Nuclear Information System (INIS)

    Gardner, R.P.

    1997-01-01

    The radiation and radioisotope gauging industry in the United States has primarily followed a path of development solely by the private sector. It has remained highly proprietary in nature, which is opposite to the path taken by many other countries. In other countries radiation gauge development has been controlled in large part by government-sponsored research and development, which has spawned many more publications in the open literature. Historically, some of the leaders have been Great Britain, Poland, France, Russia, and Australia. This has possibly led to the misconception that the development of this technology is being dominated by countries outside the United States. This is not a healthy situation-it would be good to see our industry begin to publish more in the open literature and to sponsor more research at universities. In efforts to promote more open-literature publication, the American Nuclear Society (ANS) sponsored a topical meeting on Industrial Radiation and Radioisotope Measurement Applications (IRRMA) in 1988 that was held again in 1992

  8. Status and trends in nuclear techniques in the mineral industry in India

    International Nuclear Information System (INIS)

    Eapen, A.C.; Rao, S.M.; Murthy, T.S.

    1991-01-01

    The status and use of nuclear techniques in the various parts of the mineral industry in India are reviewed. The techniques and applications include nucleonic level control in ore hoppers; radiometric density gauges; coal ash monitoring using x-ray backscattering; mineral analysis by x-ray fluorescence and radioisotope analysis; neutron and gamma logging of oil wells; radiotracer techniques in bauxite processing and in the oil industry. (UK)

  9. Ultrapulse welding: A new joining technique. [for automotive industry

    Science.gov (United States)

    Anderson, D. G.

    1972-01-01

    The ultrapulse process is a resistance welding process that utilizes unidirectional current of high magnitude for a very short time with a precisely controlled dynamic force pulse. Peak currents of up to 220,000 amperes for two to ten milliseconds are used with synchronized force pulses of up to nine thousand pounds. The welding current passing through the relatively high resistance of the interface between the parts that are being joined results in highly localized heating. Described is the UPW process as it applies to the automotive industry.

  10. Nuclear techniques in agriculture and industry in China

    International Nuclear Information System (INIS)

    Lu Yanxiao

    1993-01-01

    The presentation describes the application of nuclear techniques related to information acquisition by radiotracer and isotope-instrument getting physical parameters from measured substances, medical diagnostic information, evolution of novel substances or modification of materials through interaction of ionizing radiation with matter,mutation breeding in agriculture, cancer therapy in medicine, sterilization of medical products

  11. Simulation tools for industrial applications of phased array inspection techniques

    International Nuclear Information System (INIS)

    Mahaut, St.; Roy, O.; Chatillon, S.; Calmon, P.

    2001-01-01

    Ultrasonic phased arrays techniques have been developed at the French Atomic Energy Commission in order to improve defects characterization and adaptability to various inspection configuration (complex geometry specimen). Such transducers allow 'standard' techniques - adjustable beam-steering and focusing -, or more 'advanced' techniques - self-focusing on defects for instance -. To estimate the performances of those techniques, models have been developed, which allows to compute the ultrasonic field radiated by an arbitrary phased array transducer through any complex specimen, and to predict the ultrasonic response of various defects inspected with a known beam. Both modeling applications are gathered in the Civa software, dedicated to NDT expertise. The use of those complementary models allows to evaluate the ability of a phased array to steer and focus the ultrasonic beam, and therefore its relevancy to detect and characterize defects. These models are specifically developed to give accurate solutions to realistic inspection applications. This paper briefly describes the CIVA models, and presents some applications dedicated to the inspection of complex specimen containing various defects with a phased array used to steer and focus the beam. Defect detection and characterization performances are discussed for the various configurations. Some experimental validation of both models are also presented. (authors)

  12. Reduction of thermal models of buildings: improvement of techniques using meteorological influence models; Reduction de modeles thermiques de batiments: amelioration des techniques par modelisation des sollicitations meteorologiques

    Energy Technology Data Exchange (ETDEWEB)

    Dautin, S.

    1997-04-01

    This work concerns the modeling of thermal phenomena inside buildings for the evaluation of energy exploitation costs of thermal installations and for the modeling of thermal and aeraulic transient phenomena. This thesis comprises 7 chapters dealing with: (1) the thermal phenomena inside buildings and the CLIM2000 calculation code, (2) the ETNA and GENEC experimental cells and their modeling, (3) the techniques of model reduction tested (Marshall`s truncature, Michailesco aggregation method and Moore truncature) with their algorithms and their encoding in the MATRED software, (4) the application of model reduction methods to the GENEC and ETNA cells and to a medium size dual-zone building, (5) the modeling of meteorological influences classically applied to buildings (external temperature and solar flux), (6) the analytical expression of these modeled meteorological influences. The last chapter presents the results of these improved methods on the GENEC and ETNA cells and on a lower inertia building. These new methods are compared to classical methods. (J.S.) 69 refs.

  13. X-ray techniques for innovation in industry

    Directory of Open Access Journals (Sweden)

    Krystyna Lawniczak-Jablonska

    2014-11-01

    Full Text Available The smart specialization declared in the European program Horizon 2020, and the increasing cooperation between research and development found in companies and researchers at universities and research institutions have created a new paradigm where many calls for proposals require participation and funding from public and private entities. This has created a unique opportunity for large-scale facilities, such as synchrotron research laboratories, to participate in and support applied research programs. Scientific staff at synchrotron facilities have developed many advanced tools that make optimal use of the characteristics of the light generated by the storage ring. These tools have been exceptionally valuable for materials characterization including X-ray absorption spectroscopy, diffraction, tomography and scattering, and have been key in solving many research and development issues. Progress in optics and detectors, as well as a large effort put into the improvement of data analysis codes, have resulted in the development of reliable and reproducible procedures for materials characterization. Research with photons has contributed to the development of a wide variety of products such as plastics, cosmetics, chemicals, building materials, packaging materials and pharma. In this review, a few examples are highlighted of successful cooperation leading to solutions of a variety of industrial technological problems which have been exploited by industry including lessons learned from the Science Link project, supported by the European Commission, as a new approach to increase the number of commercial users at large-scale research infrastructures.

  14. X-ray techniques for innovation in industry.

    Science.gov (United States)

    Lawniczak-Jablonska, Krystyna; Cutler, Jeffrey

    2014-11-01

    The smart specialization declared in the European program Horizon 2020, and the increasing cooperation between research and development found in companies and researchers at universities and research institutions have created a new paradigm where many calls for proposals require participation and funding from public and private entities. This has created a unique opportunity for large-scale facilities, such as synchrotron research laboratories, to participate in and support applied research programs. Scientific staff at synchrotron facilities have developed many advanced tools that make optimal use of the characteristics of the light generated by the storage ring. These tools have been exceptionally valuable for materials characterization including X-ray absorption spectroscopy, diffraction, tomography and scattering, and have been key in solving many research and development issues. Progress in optics and detectors, as well as a large effort put into the improvement of data analysis codes, have resulted in the development of reliable and reproducible procedures for materials characterization. Research with photons has contributed to the development of a wide variety of products such as plastics, cosmetics, chemicals, building materials, packaging materials and pharma. In this review, a few examples are highlighted of successful cooperation leading to solutions of a variety of industrial technological problems which have been exploited by industry including lessons learned from the Science Link project, supported by the European Commission, as a new approach to increase the number of commercial users at large-scale research infrastructures.

  15. L’industrie lithique magdalénienne du gisement de plein-air de la Corne-de-Rollay (Couleuvre, Allier : entre respect des normes et variabilité des chaînes opératoires The Magdalenian lithic industry from the openair site of la Corne-de-Rollay (Couleuvre, Allier: production standards and production lines variability

    Directory of Open Access Journals (Sweden)

    Raphaël Angevin

    2011-01-01

    Full Text Available Le site de la Corne-de-Rollay (Couleuvre, Allier correspond à un vaste gisement de plein-air localisé sur le sommet d’un plateau de basse altitude, entre val de Cher et val d’Allier. La présente contribution expose les résultats de l’étude effectuée sur l’industrie lithique provenant de l’occupation magdalénienne de ce dernier gisement. Réalisée à partir de deux grands types de matériaux (les silex marins allochtones et les roches siliceuses d’origine locale, cette industrie témoigne de la mise en œuvre de plusieurs schémas opératoires de débitage ayant pour finalité principale la production de lames et de lamelles. La forte variabilité des schémas opératoires rencontrés dans la production lamellaire nous a conduit à nous interroger sur le degré d’autonomie accordé aux différents systèmes de production, visant à la confection de supports aux caractéristiques morpho-techniques parfois proches et aux propriétés morpho-fonctionnelles pouvant souvent être considérées comme analogues ou complémentaires. Cette dernière réalité nous invite donc à envisager sous un jour nouveau le phénomène particulier de “ ramification des chaînes opératoires ” (Bourguignon et al. 2004, pouvant répondre à des objectifs de production semblables, mais s’établissant dans le cadre d’échelles de temps distinctes. In fine, l’attribution chrono-culturelle de cet assemblage au Magdalénien moyen est discutée.La Corne-de-Rollay (Couleuvre, Allier is a vast open-air camp-site located on the top of a small plateau, between Cher valley and Allier valley. Here are presented the results of a study of the lithic industry from the Magdalenian occupation of this settlement. Composed of two large groups of raw materials (flint and local siliceous rocks, this industry shows several operative schemes to produce blades and bladelets. The high variability of different bladelets production techniques leads us to

  16. Energy policy conference on the regulation of energy industries; Conference de politique energetique sur la regulation des industries energetiques

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-11-01

    This document is the report of the conference meeting jointly organized by the French general plan commission and the general direction of energy and raw materials on the regulation of energy industries: 1 - the changes in the regulation of public utilities in competition: harmonization, respect of impartiality and social cohesion, organization of a loyal competition, specialized regulation and regulation of competition, open debates; 2 - towards an homogenous model of regulatory authority?: the US model (collegial and hybrid organizations), the UK model (individual and independent), missions of regulation and institutional 'meccano', theory and practice, draft classification of the institutional approaches of IEA countries (role of ministries and regulatory agencies), independent regulatory authorities or not, significant differences in converging models, dominant types of regulation in the different sectors, situation of the French energy regulatory system (institutional plan, regulation processes, relations of the regulation authority with the government), reasons of the differences between different countries, expected evolution of the regulation systems in the coming years. (J.S.)

  17. Energy policy conference on the regulation of energy industries; Conference de politique energetique sur la regulation des industries energetiques

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-11-01

    This document is the report of the conference meeting jointly organized by the French general plan commission and the general direction of energy and raw materials on the regulation of energy industries: 1 - the changes in the regulation of public utilities in competition: harmonization, respect of impartiality and social cohesion, organization of a loyal competition, specialized regulation and regulation of competition, open debates; 2 - towards an homogenous model of regulatory authority?: the US model (collegial and hybrid organizations), the UK model (individual and independent), missions of regulation and institutional 'meccano', theory and practice, draft classification of the institutional approaches of IEA countries (role of ministries and regulatory agencies), independent regulatory authorities or not, significant differences in converging models, dominant types of regulation in the different sectors, situation of the French energy regulatory system (institutional plan, regulation processes, relations of the regulation authority with the government), reasons of the differences between different countries, expected evolution of the regulation systems in the coming years. (J.S.)

  18. Impact de la preparation des anodes crues et des conditions de cuisson sur la fissuration dans des anodes denses

    Science.gov (United States)

    Amrani, Salah

    La fabrication de l'aluminium est realisee dans une cellule d'electrolyse, et cette operation utilise des anodes en carbone. L'evaluation de la qualite de ces anodes reste indispensable avant leur utilisation. La presence des fissures dans les anodes provoque une perturbation du procede l'electrolyse et une diminution de sa performance. Ce projet a ete entrepris pour determiner l'impact des differents parametres de procedes de fabrication des anodes sur la fissuration des anodes denses. Ces parametres incluent ceux de la fabrication des anodes crues, des proprietes des matieres premieres et de la cuisson. Une recherche bibliographique a ete effectuee sur tous les aspects de la fissuration des anodes en carbone pour compiler les travaux anterieurs. Une methodologie detaillee a ete mise au point pour faciliter le deroulement des travaux et atteindre les objectifs vises. La majorite de ce document est reservee pour la discussion des resultats obtenus au laboratoire de l'UQAC et au niveau industriel. Concernant les etudes realisees a l'UQAC, une partie des travaux experimentaux est reservee a la recherche des differents mecanismes de fissuration dans les anodes denses utilisees dans l'industrie d'aluminium. L'approche etait d'abord basee sur la caracterisation qualitative du mecanisme de la fissuration en surface et en profondeur. Puis, une caracterisation quantitative a ete realisee pour la determination de la distribution de la largeur de la fissure sur toute sa longueur, ainsi que le pourcentage de sa surface par rapport a la surface totale de l'echantillon. Cette etude a ete realisee par le biais de la technique d'analyse d'image utilisee pour caracteriser la fissuration d'un echantillon d'anode cuite. L'analyse surfacique et en profondeur de cet echantillon a permis de voir clairement la formation des fissures sur une grande partie de la surface analysee. L'autre partie des travaux est basee sur la caracterisation des defauts dans des echantillons d'anodes crues

  19. Expert system reasoning techniques applicable to the electric power industry

    International Nuclear Information System (INIS)

    Touchton, R.A.

    1987-01-01

    This paper describes the applicability of three problem solving paradigms adopted from the artificial intelligence discipline of computer sciences, which have been used in developing nuclear plant expert systems. Each technique is briefly defined and an example is presented that shows how that technique was used in developing an expert system application prototype. The three paradigms and their associated example systems are: (1) rule-based reasoning: reactor emergency action level monitor (REALM) for the Electric Power Research Institute, (2) object-oriented programming: accident diagnosis and prognosis aid for the US Department of Energy, and (3) model-based reasoning: knowledge-based monitoring and control system for the Electric Power Research Institute

  20. From the coupling between ion beam analysis techniques and physico-chemical characterization methods to the study of irradiation effects on materials behaviour; Du couplage des techniques d'analyse par faisceaux d'ions et des methodes de caracterisation physico-chimique a l'etude des effets d'irradiation sur le comportement des materiaux

    Energy Technology Data Exchange (ETDEWEB)

    Millard-Pinard, N

    2003-07-01

    The general purpose of my research work is to follow and to interpret the surface evolution of materials, which have received several treatments. During my PhD and my post-doc work, my field of research was tribology. Since I arrived in the 'Aval du Cycle Electronucleaire' group of the Institut de Physique Nucleaire de Lyon, my research activities are in line with the CNRS program 'PACE ' (Programme sur l'Aval du Cycle Electronucleaire) within the ACTINET network. They are coordinated by the PARIS (Physico-chimie des actinides et autres radioelements en solution et aux interfaces) and NOMADE (NOuveaux MAteriaux pour les DEchets) GDR with ANDRA (Agence Nationale pour la gestion des Dechets RAdioactifs), EDF and IRSN (Institut de Radioprotection et de Surete Nucleaire) as partner organisations. My work focused on the study of fission products and actinides migration in barrier materials, which may be capable of assuring the long term safety of deep geological repositories. Until now, it was necessary to use the coupling of ion beam analysis techniques and physico-chemical characterization techniques. During the last few months, I have became interested in understanding radiolytic effects. This new orientation has led us to use ion beams as an irradiating tool. These irradiation experiments are pursued in three major projects. The study of cobalt sulfide inhibition effects of radiolysis gas production during the irradiation of model organic molecules. This is a collaboration with the IRSN, the Institut de Recherche sur la Catalyse and the Ecole Nationale Superieure des Mines de Saint-Etienne. A PhD, co-directed by M. Pijolat from ENSMSE and myself, concerning this study will start in October 2003. Water radiolysis effects on iron corrosion are also studied in the particular case of vitrified nuclear waste containers, which will be stored in deep geological repositories. One ANDRA financed PhD, co-directed by Nathalie Moncoffre and myself, is dedicated to this study

  1. From the coupling between ion beam analysis techniques and physico-chemical characterization methods to the study of irradiation effects on materials behaviour; Du couplage des techniques d'analyse par faisceaux d'ions et des methodes de caracterisation physico-chimique a l'etude des effets d'irradiation sur le comportement des materiaux

    Energy Technology Data Exchange (ETDEWEB)

    Millard-Pinard, N

    2003-07-01

    The general purpose of my research work is to follow and to interpret the surface evolution of materials, which have received several treatments. During my PhD and my post-doc work, my field of research was tribology. Since I arrived in the 'Aval du Cycle Electronucleaire' group of the Institut de Physique Nucleaire de Lyon, my research activities are in line with the CNRS program 'PACE ' (Programme sur l'Aval du Cycle Electronucleaire) within the ACTINET network. They are coordinated by the PARIS (Physico-chimie des actinides et autres radioelements en solution et aux interfaces) and NOMADE (NOuveaux MAteriaux pour les DEchets) GDR with ANDRA (Agence Nationale pour la gestion des Dechets RAdioactifs), EDF and IRSN (Institut de Radioprotection et de Surete Nucleaire) as partner organisations. My work focused on the study of fission products and actinides migration in barrier materials, which may be capable of assuring the long term safety of deep geological repositories. Until now, it was necessary to use the coupling of ion beam analysis techniques and physico-chemical characterization techniques. During the last few months, I have became interested in understanding radiolytic effects. This new orientation has led us to use ion beams as an irradiating tool. These irradiation experiments are pursued in three major projects. The study of cobalt sulfide inhibition effects of radiolysis gas production during the irradiation of model organic molecules. This is a collaboration with the IRSN, the Institut de Recherche sur la Catalyse and the Ecole Nationale Superieure des Mines de Saint-Etienne. A PhD, co-directed by M. Pijolat from ENSMSE and myself, concerning this study will start in October 2003. Water radiolysis effects on iron corrosion are also studied in the particular case of vitrified nuclear waste containers, which will be stored in deep geological repositories. One ANDRA financed PhD, co-directed by Nathalie Moncoffre and myself, is

  2. Advanced computer graphics techniques as applied to the nuclear industry

    International Nuclear Information System (INIS)

    Thomas, J.J.; Koontz, A.S.

    1985-08-01

    Computer graphics is a rapidly advancing technological area in computer science. This is being motivated by increased hardware capability coupled with reduced hardware costs. This paper will cover six topics in computer graphics, with examples forecasting how each of these capabilities could be used in the nuclear industry. These topics are: (1) Image Realism with Surfaces and Transparency; (2) Computer Graphics Motion; (3) Graphics Resolution Issues and Examples; (4) Iconic Interaction; (5) Graphic Workstations; and (6) Data Fusion - illustrating data coming from numerous sources, for display through high dimensional, greater than 3-D, graphics. All topics will be discussed using extensive examples with slides, video tapes, and movies. Illustrations have been omitted from the paper due to the complexity of color reproduction. 11 refs., 2 figs., 3 tabs

  3. Beef identification in industrial slaughterhouses using machine vision techniques

    Directory of Open Access Journals (Sweden)

    J. F. Velez

    2013-10-01

    Full Text Available Accurate individual animal identification provides the producers with useful information to take management decisions about an individual animal or about the complete herd. This identification task is also important to ensure the integrity of the food chain. Consequently, many consumers are turning their attention to issues of quality in animal food production methods. This work describes an implemented solution for individual beef identification, taking in the time from cattle shipment arrival at the slaughterhouse until the animals are slaughtered and cut up. Our beef identification approach is image-based and the pursued goals are the correct automatic extraction and matching between some numeric information extracted from the beef ear-tag and the corresponding one from the Bovine Identification Document (BID. The achieved correct identification results by our method are near 90%, by considering the practical working conditions of slaughterhouses (i.e. problems with dirt and bad illumination conditions. Moreover, the presence of multiple machinery in industrial slaughterhouses make it difficult the use of Radio Frequency Identification (RFID beef tags due to the high risks of interferences between RFID and the other technologies in the workplace. The solution presented is hardware/software since it includes a specialized hardware system that was also developed. Our approach considers the current EU legislation for beef traceability and it reduces the economic cost of individual beef identification with respect to RFID transponders. The system implemented has been in use satisfactorily for more than three years in one of the largest industrial slaughterhouses in Spain.

  4. Industry

    International Nuclear Information System (INIS)

    Schindler, I.; Wiesenberger, H.

    2001-01-01

    This chapter of the environmental control report deals with the environmental impact of the industry in Austria. It gives a review of the structure and types of the industry, the legal framework and environmental policy of industrial relevance. The environmental situation of the industry in Austria is analyzed in detail, concerning air pollution (SO 2 , NO x , CO 2 , CO, CH 4 , N 2 O, NH 3 , Pb, Cd, Hg, dioxin, furans), waste water, waste management and deposit, energy and water consumption. The state of the art in respect of the IPPC-directives (European Integrated Pollution Prevention and Control Bureau) concerning the best available techniques of the different industry sectors is outlined. The application of European laws and regulations in the Austrian industry is described. (a.n.)

  5. Impact des politiques climatiques sur les industries énergie-intensives

    OpenAIRE

    Branger , Frédéric

    2015-01-01

    This thesis contributes to the literature on carbon leakage and competitiveness losses in energy-intensive industries generated by uneven climate policies. After a meta-analysis of modelling studies assessing carbon leakage with or without Border Carbon Adjustments; we use time series econometrics and find no evidence of competitiveness-driven operational leakage due to the European Union Emissions Trading System (EU ETS) for steel and cement. Next, we decompose emissions the European cement ...

  6. Les hydrocarbures aromatiques polycycliques dans l'environnement : la réhabilitation des anciens sites industriels The Polycyclic Aromatic Hydrocarbons in the Environment : the Former Industrial Sites Remediation

    Directory of Open Access Journals (Sweden)

    Costes J. M.

    2006-12-01

    Full Text Available Les hydrocarbures aromatiques polycycliques ou HAP peuvent être d'origine naturelle mais ils proviennent principalement des processus de pyrolyse. On peut les retrouver dans les sols de certains anciens sites industriels. Cela peut être le cas des sites d'anciennes usines à gaz. Même si aucune conséquence sur la santé humaine n'a été signalée et même si les risques paraissent virtuels, le principe de précaution rend nécessaire de s'occuper des risques liés à ces anciens sites industriels. Gaz de France, propriétaire de 467 sites d'anciennes usines à gaz assume l'héritage industriel dans le cadre d'un protocole signé avec le ministère de l'Environnement. Après une étude des sols, une évaluation des risques est réalisée. En fonction des résultats de cette évaluation des risques et de l'usage du site (actuel et prévu, des solutions de traitement peuvent être mises en Suvre. Parmi les techniques applicables aux sols pollués par des HAP, un intérêt particulier s'est porté sur les traitements biologiques, en pleine évolution, qui offrent une solution économique bien adaptée au traitement de grands volumes de sols souillés par une pollution organique moyennement concentrée. Polycyclic aromatic hydrocarbons (PAHs can be found under natural conditions but they can be produced by pyrolysis processes. They can be found in former industrial sites subsoil, especially on Manufactured Gas Plant sites (MGP sites. Gaz de France has inherited the patrimony of former French gas companies on nationalisation in 1946; consequently, Gaz De France is still the owner of 467 of manufactured gas plants. Even if no impact on human health has been detected and even if the risks seem to be virtual, Gaz de France has to prevent any environmental consequence due to the possible presence of residues in the subsoil of the sites: a protocol has been signed with the French Ministry of Environment. Following the investigations on the site, a

  7. Days on safety of industrial radiographic controls; Securite des controles radiographiques industriels

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    This program is divided in three parts: the context and the regulations, the preparation and the implementation, the tools of prevention and the initiatives and the perspectives.In the first part devoted to the context and regulation are: the context by the Authority of nuclear safety (A.S.N.), the regulation referential, the transport of gamma-graphs; in the second part are the distribution of liabilities, materials and associated requirements, the feedback of incidents and exploitation of it, training and base requirements, works of S.F.R.P./C.O.F.R.E.N.D. and the A.S.N. position; the third part includes help to evaluation of risks at working places of industry radiologists, dosimetry study of a working place, guide to evaluate oneself; the fourth part devoted to the initiatives and the perspectives are: regional experiences charters of good practices in industry radiography, integration of works and deployment by the members of the C.O.F.R.E.N.D., perspectives in matter of prevention of occupational risks in the area of industry radiography. (N.C.)

  8. Nouvelles Techniques d'Intervention sur la Corrosion des Armatures du Béton Armé

    CERN Document Server

    Colloca, C

    1999-01-01

    Les principaux dégâts constatés dans les armatures passives du béton armé sont la corrosion généralisée et la corrosion locale. Ces dégradations sont provoquées soit par la carbonatation du béton soit par le contact avec l'eau pure ou l'eau chargée de chlorures pénétrant dans les pores et dans les fissures de surface. Ce document présente de nouvelles techniques d'intervention, fondées sur d'anciens principes, introduites pour le traitement électrochimique des zones altérées liées aux différentes conditions. La réalcalinisation (dans le cas de béton carbonaté) permet d'augmenter le pH du béton et de rétablir un niveau de basicité garantissant la passivation de l'armature. La désalification (dans le cas de béton entamé par les chlorures) provoque l'élimination des ions chlorure à travers la surface du béton. Les avantages de ces traitements, par rapport aux anciennes techniques, sont appréciables si l'on considère la durée d'exécution et leur coût moins élevé.

  9. Radiation protection optimisation techniques and their application in industry

    Energy Technology Data Exchange (ETDEWEB)

    Lefaure, C

    1997-12-31

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author) 2 graphs, 5 figs., 3 tabs.

  10. Industrial radiography with Ir-192 using computed radiographic technique

    International Nuclear Information System (INIS)

    Ngernvijit, Narippawaj; Punnachaiya, Suvit; Chankow, Nares; Sukbumperng, Ampai; Thong-Aram, Decho

    2003-01-01

    The aim of this research is to study the utilization of a low activity Ir-192 gamma source for industrial radiographic testing using the Computed Radiography (CR) system. Due to a photo-salbutamol Imaging Plate (I P) using in CR is much more radiation sensitive than a type II film with lead foil intensifying screen, the exposure time with CR can be significantly reduced. For short-lived gamma-ray source like Ir-192 source, the exposure time must be proportionally increased until it is not practical particularly for thick specimens. Generally, when the source decays to an activity of about 5 Ci or less, it will be returned to the manufacturer as a radioactive waste. In this research, the optimum conditions for radiography of a 20 mm thick welded steel sample with 2.4 Ci Ir-192 was investigated using the CR system with high resolution image plate, i.e. type Bas-SR of the Fuji Film Co. Ltd. The I P was sandwiched by a pair of 0.25 mm thick Pb intensifying sere en. Low energy scattered radiations was filtered by placing another Pb sheet with a thickness of 3 mm under the cassette. It was found that the CR image could give a contrast sensitivity of 2.5 % using only 3-minute exposure time which was comparable to the image taken by the type II film with Pb intensifying screen using the exposure time of 45 minutes

  11. Radiation protection optimisation techniques and their application in industry

    International Nuclear Information System (INIS)

    Lefaure, C.

    1996-01-01

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author)

  12. Radiation protection optimisation techniques and their application in industry

    Energy Technology Data Exchange (ETDEWEB)

    Lefaure, C

    1996-12-31

    Since the International Commission on Radiation Protection (ICRP) recommendation 60, the optimisation principle appears to be the core of the radiation protection system. In practice applying it, means implementing an approach both predictive and evolutionary - that relies essentially on a prudent and responsible state of mind. the formal expression of this process, called optimization procedure, implies and indispensable tool for its implementation: the system of monetary values for the unit of collective dose. During the last few years, feed ALARA principle means that a global work management approach must be adopted, considering together all factors contributing to radiation dose. In the nuclear field, the ALARA approach appears to be more successful when implemented in the framework of a managerial approach through structure ALARA programmes. Outside the nuclear industry it is necessary to clearly define priorities through generic optimisation studies and ALARA audits. At the international level much efforts remain to be done to expand efficiently the ALARA process to internal exposure as well as to public exposure. (author) 2 graphs, 5 figs., 3 tabs.

  13. Technical management techniques for identification and control of industrial safety and pollution hazards

    Science.gov (United States)

    Campbell, R.; Dyer, M. K.; Hoard, E. G.; Little, D. G.; Taylor, A. C.

    1972-01-01

    Constructive recommendations are suggested for pollution problems from offshore energy resources industries on outer continental shelf. Technical management techniques for pollution identification and control offer possible applications to space engineering and management.

  14. Report of the project ARCAL XLIII: Paraguay: industrial application of tracer techniques and nuclear control systems

    International Nuclear Information System (INIS)

    Acosta Cabello, Rodolfo

    2000-12-01

    Paraguay needs to improve the productivity in several service industries. Main interest has been devoted to introducing new alternative techniques for the evaluation of the processes of water treatment plants for human consumption and waste waters [es

  15. The need for novel model order reduction techniques in the electronics industry (Chapter 1)

    NARCIS (Netherlands)

    Schilders, W.H.A.; Benner, P.; Hinze, M.; Maten, ter E.J.W.

    2011-01-01

    In this paper, we discuss the present and future needs of the electronics industry with regard to model order reduction. The industry has always been one of the main motivating fields for the development of MOR techniques, and continues to play this role. We discuss the search for provably passive

  16. Papers of All-Polish Conference on Nuclear Techniques in Industry, Medicine, Agriculture and Environmental Protection

    International Nuclear Information System (INIS)

    2002-01-01

    These proceedings comprise papers presented at All-Polish Conference on nuclear techniques in industry, medicine, agriculture and environmental protection. Most of the papers are in the field of uses of radiation sources and particle beams in industry, radiation chemistry, nuclear medicine and dosimetry, environmental sciences

  17. Techniques for Automated Testing of Lola Industrial Robot Language Parser

    Directory of Open Access Journals (Sweden)

    M. M. Lutovac

    2014-06-01

    Full Text Available The accuracy of parsing execution directly affects the accuracy of semantic analysis, optimization and object code generation. Therefore, parser testing represents the basis of compiler testing. It should include tests for correct and expected, but also for unexpected and invalid cases. Techniques for testing the parser, as well as algorithms and tools for test sentences generation, are discussed in this paper. The methodology for initial testing of a newly developed compiler is proposed. Generation of negative test sentences by modifying the original language grammar is described. Positive and negative test cases generated by Grow, Purdom’s algorithm with and without length control, CDRC-P algorithm and CDRC-P algorithm with length control are applied to the testing of L-IRL robot programming language. For this purpose two different tools for generation of test sentences are used. Based on the presented analysis of possible solutions, the appropriate method can be chosen for testing the parser for smaller grammars with many recursive rules.

  18. Study of heterogeneous multiplying and non-multiplying media by the neutron pulsed source technique; Etude des milieux heterogenes multiplicateurs et non-multiplicateurs par la technique de la source pulsee de neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Deniz, V [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-06-01

    The pulsed neutron technique consists essentially in sending in the medium to be studied a short neutron pulse and in determining the asymptotic decay constant of the generated population. The variation of the decay constant as a function of the size of the medium allows the medium characteristics to be defined. This technique has been largely developed these last years and has been applied as well to moderator as to multiplying media, in most cases homogeneous ones. We considered of interest of apply this technique to lattices, to see if useful informations could be collected for lattice calculations. We present here a general theoretical study of the problem, and results and interpretation of a series of experiments made on graphite lattices. There is a good agreement for non-multiplying media. In the case of multiplying media, it is shown that the age value used until now in graphite lattices calculations is over-estimated by about 10 per cent. [French] La technique de la pulsation neutronique consiste essentiellement a envoyer dans le milieu a etudier une courte bouffee de neutrons et a determiner la constante de decroissance asymptotique de la population engendree. La variation de cette constante de decroissance en fonction des dimensions du milieu permet de determiner ses caracteristiques. Cette technique a connu ces dernieres annees un grand essor et a ete appliquee a des moderateurs et des milieux multiplicateurs. Il s'agissait dans la plupart des cas de milieux homogenes. Il nous a semble interessant de l'utiliser dans le cas des reseaux, afin de voir si ces experiences peuvent fournir des renseignements utiles aux calculs. Nous presentons ici une etude theorique generale du probleme, ainsi que les resultats et l'interpretation d'une serie d'experiences faites sur des reseaux a graphite. L'accord est bon dans le cas des reseaux non-multiplicateurs. Dans le cas des reseaux multiplicateurs, on montre que la valeur de l'age utilisee jusqu'ici dans les calculs

  19. Industrial mixing techniques for Hanford double-shell tanks

    International Nuclear Information System (INIS)

    Daymo, E.A.

    1997-09-01

    Jet mixer pumps are currently the baseline technology for sludge mobilization and mixing in one-million gallon double-shell tanks at the Hanford and Savannah River Sites. Improvements to the baseline jet mixer pump technology are sought because jet mixer pumps have moving parts that may fail or require maintenance. Moreover, jet mixers are relatively expensive, they heat the waste, and, in some cases, may not mobilize enough of the sludge. This report documents a thorough literature search for commercially available applicable mixing technologies that could be used for double-shell tank sludge mobilization and mixing. Textbooks, research articles, conference proceedings, mixing experts, and the Thomas Register were consulted to identify applicable technologies. While there are many commercial methods that could be used to mobilize sludge or mix the contents of a one-million gallon tank, few will work given the geometrical constraints (e.g., the mixer must fit through a 1.07-m-diameter riser) or the tank waste properties (e.g., the sludge has such a high yield stress that it generally does not flow under its own weight). Pulsed fluid jets and submersible Flygt mixers have already been identified at Hanford and Savannah River Sites for double-shell tank mixing applications. While these mixing technologies may not be applicable for double-shell tanks that have a thick sludge layer at the bottom (since too many of these mixers would need to be installed to mobilize most of the sludge), they may have applications in tanks that do not have a settled solids layer. Retrieval projects at Hanford and other U.S. Department of Energy sites are currently evaluating the effectiveness of these mixing techniques for tank waste applications. The literature search did not reveal any previously unknown technologies that should be considered for sludge mobilization and mixing in one-million gallon double-shell tanks

  20. Materials of All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection

    International Nuclear Information System (INIS)

    2005-01-01

    The All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection is cyclic (in 3 year period) conference being a broad review of state of art and development of all nuclear branches cooperated with industry and other branches of national economy and public life in Poland. The conference has been divided in one plenary session and 6 problem sessions as follow: Environmental protection, earth sciences, protection of cultural objects; Industrial applications; applications in medicine, medical apparatus; measurement methods, simulations, experiment planning; radiation techniques; laboratories, metrology

  1. Monsieur Omar Fassi Fihri Secrétaire perpétuel Académie HASSAN II des Sciences et Techniques Royaume du Maroc

    CERN Document Server

    Maximilien Brice

    2010-01-01

    CERN-HI-1007135 01: M. Gouighri, Boursier de l’Académie des Sciences, Université Hassan II; J. Collot, Directeur du Laboratoire international associé; R. Heuer,\tDirecteur général du CERN;O. Fassi Fehri, Secrétaire perpétuel, Académie Hassan II des Sciences et Techniques, Maroc; S. Boutouil, Boursière du Laboratoire international associé; R. Klapisch, Fondation Partager le Savoir, Président et fondateur; G.Carnot, Président de la Fondation Carnot.

  2. Meeting around industrial sites; Concertation autour des sites d'installations industrielles

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Th. [Centre d' etude sur l' Evaluation de la Protection dans le domaine Nucleaire (CEPN), 92 - Fontenay aux Roses (France); Sene, M. [Groupement de Scientifiques pour l' Information sur l' Energie Nucleaire, 91 - Orsay (France); Melguen, M. [Electricite de France (EDF), 75 - Paris (France); Saint-Raymond, Ph. [Direction Generale de la Surete Nucleaire et de la Radioprotection, 75 - Paris (France); Oudiz, A. [Institut de Radioprotection et de Surete Nucleaire, 92 - Fontenay-aux-Roses (France); Brie, J. [Charente Nature (France); Schmitt, P. [CLS de Fessenheim, 68 (France); Verot, Y [Atofina, 92 -Paris la Defense (France); Quintin, Ch. [DRIRE Rhone Alpes, 69 (France); Dubuis, Th. [Secretariat Permanent pour la Prevention des Pollutions Industrielles, 59 - Dunkerque (France); Adelfa, J.S.; Hocquet, M.P. [CLCV, France (France); Gheerardyn, P. [MEDEF Cote d' Opale (France); Villers, S. [EDA, France (France); Modrzejewski, F. [DRIRE Nord-Pas-de-Calais (France); Gadbois, S.; Heriard-Dubreuil, G. [MUTADIS, 75 - Paris (France); Geismar, N.; Eimer, M. [CLI de Saint-Laurent (France); Andre, S. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France); Vindimian, E. [Institut National de l' Environnement Industriel et des Risques, 60 - Verneuil en Halatte (INERIS) (France); Remond-Gouilloud, M. [Universite Paris-Sorbonne, 75 (France)

    2005-07-01

    Following the research work on the ' stakes in the social dialogue around the follow-up of the nuclear industrial installations ' engaged by the I.R.S.N. in 2000, a seminar was organized on January 21. and 22., 2003 in Ville d Avray. This seminar gathered personalities of different origins (administration, institutional experts, operators, associations, Local Commissions of Information, elected representatives) to discuss and enrich the conclusions of the research work and elaborate collectively a contribution to the current remarks in France on the public debate and the processes of dialogue. The present report establishes the acts of this seminar and redraws all the discussions between the participants. (N.C.)

  3. La gestion des gestionnaires de projets: Le cas de l'industrie aerospatiale au Quebec

    Science.gov (United States)

    Petit, Marie-Claude

    This research focuses on the management of project managers (PMs) working in high technology organizations. In particular, it examines how these professionals are taken charge of from a human resources management (HRM) standpoint in firms within the aerospace industry in Quebec. The literature in the field of project management generally depicts PMs as entrepreneurs and resource managers, managing human resources (e.g. project team members) among other things. It also defines them as single-handedly responsible for managing their own career, stress and motivation. This profile suggests that once selected and assigned to projects, PMs receive little attention in terms of HRM from the organization. It is hardly conceivable, however, that PMs would move about completely on their own within the organization, let alone that they wouldn't represent any special challenge in terms of HRM, as the ones the literature so clearly underlines for project team members. The review of the literature also reveals that the subject of HRM as applied to PMs is poorly documented empirically, especially on the topic of what particular challenges the project context might bring up for the HRM of PMs. There is also little told about the actors involved in supporting and contributing to meet the challenges that arise out of managing PMs. This study sought to discern those challenges and the means put forth to address them. Also, it wanted to identify the actors of the HRM of PMs, their roles, their skills, and their relationships, among themselves and with the PMs, in order to efficiently take charge of them. This study also wanted to demonstrate the logic that ties the means put forth by the identified actors with the objectives PM-employing organizations want to reach. Finally, the study wanted to identify the impact of the HRM of PMs as it is occurring in organizations. The Quebec aerospace sector was chosen as the field of research primarily because the success of projects in

  4. Sediment remediation treatment techniques for the Venice industrial canals

    Energy Technology Data Exchange (ETDEWEB)

    Pippa, R.; Scanferla, P.; Cammarata, F.; Zampieri, L.; Carlon, C. [Consorzio Venezia Ricerche (Italy); Pavoni, B. [Ca' Foscari University of Venice (Italy). Dept. of Environmental Sciences; Pannocchia, G. [Venezia Technologie SpA, Venice (Italy); Hreglich, S. [Stazione Sperimentale del Vetro, Venice (Italy); Avezzu, F. [Depuracque Impianti srl, Venice (Italy)

    2003-07-01

    The main objective of SeRTech project (Sediment Remediation Technologies) is to develop an integrated cost-effective treatment system to address heterogeneous contamination and matrixes, such as those of Venice lagoon dredged materials. Seven treatment techniques, selected over a large array, have been tested: Thermal Desorption. A preliminary set of isothermal treatments at different temperatures was performed to evaluated the losses of organic and the most volatile metals (such as Pb and As). An almost full volatilisation of organic compounds was observed at temperatures ranging between 200 and 300 C. Chemical stabilization-solidification. Depuracque Impianti srl process uses innovative patented additives (polimers and superplasticizers) to immobilize heavy metals into cement pellets. Solvent extraction. Organic contaminants such as PAHs and PCBs were extracted from sediments by using ethyl acetate. The results showed that solvent extraction obtained high efficiency in removal of PAHs and other organic contaminants. Immobilization of heavy metals employing sulfate-reducing bacteria. High Gradient Magnetic Separation (HGMS). Sulfate reducing bacteria (SBR) produce an iron sulfide containing biomass with a high capability to adsorbe hevy metals and some organic compounds. This biomass can be separated through a high gradient magnetic field removing a substantial fraction of contaminants. Vitrification. Sediment was mixed with other inorganic wastes (glass cullet, feldsphatic tailings) and low amounts of row material to obtain an inert glass, which in turn can be recycled into other useful products, for example glass fibres, foam glass and glass ceramics. Phytoremediation. Phragmites australis (Cav.), Trin; Juncus Iacustrus, Arthrocnmemum fruticosum, Spartina maritima, Helianthus annuus L., Zea mais L., Brassica napus L., Brassica juncea L. have been selected to verify limit and efficiency of phytoextraction for heavy metals (Zn, Pb, Hg, Cd, As, Ni). Not only

  5. Evaluation des techniques de production du beurre de karité au Togo

    African Journals Online (AJOL)

    The results obtained showed that 31.25% of production units were using the classic churning, followed by Fulani churning processes (25.00%) and direct cooking (25.00%). Industrial technology (UIP1 and UIP2: 06.25%) and churning without roasting (06.25%) are the least practices. Butter yields found are: 49.00% (UIP1); ...

  6. Uncertainty in safety : new techniques for the assessment and optimisation of safety in process industry

    NARCIS (Netherlands)

    Rouvroye, J.L.; Nieuwenhuizen, J.K.; Brombacher, A.C.; Stavrianidis, P.; Spiker, R.Th.E.; Pyatt, D.W.

    1995-01-01

    At this moment there is no standardised method for the assessment for safety in the process industry. Many companies and institutes use qualitative techniques for safety analysis while other companies and institutes use quantitative techniques. The authors of this paper will compare different

  7. Comparison of de-noising techniques of scintigraphic images; Comparaison de techniques de debruitage des images scintigraphiques

    Energy Technology Data Exchange (ETDEWEB)

    Kirkove, M.; Seret, A. [Liege Univ., Imagerie Medicale Experimentale, Institut de Physique (Belgium)

    2007-05-15

    Scintigraphic images are strongly affected by Poisson noise. This article presents the results of a comparison between de-noising methods for Poisson noise according to different criteria: the gain in signal-to-noise ratio, the preservation of resolution and contrast. and the visual quality. The wavelet techniques recently developed to de-noise Poisson noise limited images are divided into two groups based on: (1) the Haar representation. 1 (2) the transformation of Poisson noise into white Gaussian noise by the Haar-Fisz transform followed by a de-noising. In this study, three variants of the first group and three variants of the second. including the adaptative Wiener filter, four types of wavelet thresholding and the Bayesian method of Pizurica were compared to Metz and Hanning filters and to Shine, a systematic noise elimination process. All these methods, except Shine, are parametric. For each of them, ranges of optimal values for the parameters were highlighted as a function of the aforementioned criteria. The intersection of ranges for the wavelet methods without thresholding was empty, and these methods were therefore not further compared quantitatively. The thresholding techniques and Shine gave the best results in resolution and contrast. The largest improvement in signal-to-noise ratio was obtained by the filters. Ideally, these filters should be accurately defined for each image. This is difficult in the clinical context. Moreover. they generate oscillation artefacts. In addition, the wavelet techniques did not bring significant improvements, and are rather slow. Therefore, Shine, which is fast and works automatically, appears to be an interesting alternative. (authors)

  8. Centro industrial para la «Compagnie des Lampes», en Madrid

    Directory of Open Access Journals (Sweden)

    Aymerich, Manuel

    1966-02-01

    Full Text Available The second stage of this building, constructed in the Vallecas district of Madrid, includes the workshops for the manufacture of lamp ferrules, with sections for the presses, forging and heat treatment, carbonate stores, mixes, polishing, production control, and other operations. There are also loading and packing zones, offices, first aid room, dressing rooms and services. The plan distribution, and spatial arrangement of this industrial establishment exhibit a formal and functional agile dynamism that is highly becoming.Esta nueva edificación—segunda fase—, construida en Vallecas y destinada a la fabricación de casquillos, consta en esencia de las siguientes zonas: zona de taller propiamente dicha, que alberga las secciones de prensas, mecánica, fragua y tratamientos, almacén de carbonatos, mezclas, vitrita, abrillantado, control, etc.; zona de almacenes, en conexión con los muelles para carga de camiones y carros; y la zona que aloja las oficinas, enfermería, vestuarios y servicios. Tanto la distribución de la planta como la composición de volúmenes resultan de una agilidad notable, ya que, además de su movimiento formal, expresa con sinceridad la función específica de cada cuerpo.

  9. The application of neural networks with artificial intelligence technique in the modeling of industrial processes

    International Nuclear Information System (INIS)

    Saini, K. K.; Saini, Sanju

    2008-01-01

    Neural networks are a relatively new artificial intelligence technique that emulates the behavior of biological neural systems in digital software or hardware. These networks can 'learn', automatically, complex relationships among data. This feature makes the technique very useful in modeling processes for which mathematical modeling is difficult or impossible. The work described here outlines some examples of the application of neural networks with artificial intelligence technique in the modeling of industrial processes.

  10. Nitrous Oxide from Combustion and Industry: Chemistry, Emissions and Control Protoxyde d'azote provenant de la combustion et de l'industrie : chimie, émissions et techniques de réduction

    Directory of Open Access Journals (Sweden)

    De Soete G.

    2006-11-01

    Full Text Available After an Introductory Part, presenting a survey of the present knowledge of nitrous oxide chemistry related to fossil fuel combustion and flue gas treatment, as a background for the understanding of emission factors, the paper deals successively with the average N2O emission factors from combustion and other industrial sources, and gives guidelines for appropriate N2O control technology ; with respect to the former item, some comments and criticisms on the 1991 OEDC/IPCC Report are formulated. As far as updated emission sources are concerned, emphasis is put on those which presently constitute issues : emissions from fluidized bed combustors, emissions caused by non catalytic selective NO reduction by ammonia and urea injection, N2O emissions caused by the use of automotive three-way catalysts as well as emissions from nitric acid and adipic acid manufacturing and from municipal wastes and sewage sludges incineration. Comments on the 1991 OEDC/IPCC Report mainly emphasize : (1 the surprising absence of emission factors from stationary combustion facilities and the inadequacy of some of the scarcely presented data, (2 the strange ignorance of the important effect of aging of three-way catalysts on the emission of N2O from gasoline vehicles. These omissions are the more surprising since reliable information in these two fields were already available at the period the OEDC Report was issued and or revised. For the assessment of adequate N2O control technologies, there is an urgent need for further R&D work. Presently existing understanding of homogeneous and heterogeneous N2O chemistry may provide interesting hints for N2O control, either by gas phase treatment or by catalytic reduction, depending on the concentration levels present in the off-gases to be treated. Le but de cet article est double : d'une part il fait le point sur les facteurs d'émission de N2O provenant de la combustion des combustibles fossiles et de certains autres secteurs de l'industrie

  11. Industrial technique

    International Nuclear Information System (INIS)

    Jabsen, F.S.

    1978-01-01

    An illustrative embodiment of the invention provides a control rod system locking device adapted to engage an elongated extension shaft, releasably coupled at one end to the control rod assembly and releasably coupled at its other end to the control rod drive, to prevent rotation of the shaft about its longitudinal axis with respect to the control rod assembly

  12. Industrial technique

    International Nuclear Information System (INIS)

    1975-01-01

    A typical embodiment of the invention detects leaking fuel rods by means of a radiation detector that measures the concentration of xenon-133 (Xe 133 ) within each individual rod. A collimated detector that provides signals related to the energy of incident radiation is aligned with one of the ends of a fuel rod. A statistically significant sample of the gamma radiation (γ-rays) that characterize Xe 133 is accumulated through the detector. The data so accumulated indicates the presence of a concentration of Xe 133 appropriate to a sound fuel rod, or a significantly different concentration that reflects a leaking fuel rod

  13. Chapitre 9. L'industrie pétrolière au Venezuela : rupture, conflits et gestion des espaces côtiers1

    OpenAIRE

    Ramousse, Didier

    2015-01-01

    RésuméLongtemps dévolu à des activités agro-exportatrices, le littoral vénézuélien a été complètement transformé par la croissance rapide et souvent mal contrôlée de l'industrie pétrolière, à partir des années 1930. La façade caraïbe, plus particulièrement autour du lac de Maracaibo, est devenue la région la plus dynamique et la plus prospère du pays, tandis que les populations rurales venaient s'entasser dans les villes côtières. Pourtant, le développement économique du littoral pose de nomb...

  14. Industrial and environmental applications of nuclear analytical techniques. Report of a workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    The IAEA has programme the utilisation of nuclear analytical techniques (NATs), in particular for industrial and environmental applications. A major purpose is to help the developing Member States apply their analytical capabilities optimally for socio-economic progress and development. A large number of institutions in Europe, Africa, Latin America and Asia have established X ray fluorescence (XRF) and gamma ray measurement techniques and facilities for neutron activation analysis (NAA) have been initiated in institutions in these regions. Moreover, there is a growing interest among many institutes in applying more advanced analytical techniques, such as particle induced X ray emission (PIXE) and microanalytical techniques based on X ray emission induced by conventional sources or synchrotron radiation to the analysis of environmental and biological materials and industrial products. In order to define new areas of application of NATs and to extend the range of these techniques, a number of initiatives have recently been taken. It includes a workshop on industrial and environmental applications of nuclear analytical techniques, organized by the IAEA in Vienna, 7-11 September 1998. The main objectives of the workshop were as follows: (1) to review recent applications of NATs in industrial and environmental studies; (2) to identify emerging trends in methodologies and applications of NATs; (3) to demonstrate analytical capabilities of selected NATs. The following topics were reviewed during the workshop: (1) XRF and accelerator based analytical techniques; (2) portable XRF systems and their applications in industry, mineral prospecting and processing, (3) portable gamma ray spectrometers; and (4) NAA and its applications in industry and environmental studies. Micro-XRF and micro-PIXE methods and their applications in the above fields were also discussed, including aspects of synchrotron radiation induced X ray emission.

  15. Industrial and environmental applications of nuclear analytical techniques. Report of a workshop

    International Nuclear Information System (INIS)

    1999-11-01

    The IAEA has programme the utilisation of nuclear analytical techniques (NATs), in particular for industrial and environmental applications. A major purpose is to help the developing Member States apply their analytical capabilities optimally for socio-economic progress and development. A large number of institutions in Europe, Africa, Latin America and Asia have established X ray fluorescence (XRF) and gamma ray measurement techniques and facilities for neutron activation analysis (NAA) have been initiated in institutions in these regions. Moreover, there is a growing interest among many institutes in applying more advanced analytical techniques, such as particle induced X ray emission (PIXE) and microanalytical techniques based on X ray emission induced by conventional sources or synchrotron radiation to the analysis of environmental and biological materials and industrial products. In order to define new areas of application of NATs and to extend the range of these techniques, a number of initiatives have recently been taken. It includes a workshop on industrial and environmental applications of nuclear analytical techniques, organized by the IAEA in Vienna, 7-11 September 1998. The main objectives of the workshop were as follows: (1) to review recent applications of NATs in industrial and environmental studies; (2) to identify emerging trends in methodologies and applications of NATs; (3) to demonstrate analytical capabilities of selected NATs. The following topics were reviewed during the workshop: (1) XRF and accelerator based analytical techniques; (2) portable XRF systems and their applications in industry, mineral prospecting and processing, (3) portable gamma ray spectrometers; and (4) NAA and its applications in industry and environmental studies. Micro-XRF and micro-PIXE methods and their applications in the above fields were also discussed, including aspects of synchrotron radiation induced X ray emission

  16. influence des engins et techniques de peche sur l'abondance

    African Journals Online (AJOL)

    ACSS

    17 févr. 2017 ... calculated using XLSTAT Software. Ordinary kriging technique in ArcGis 9.3 Software was used to map the measured ... Further studies are needed to develop a plan for sustainable management of the fisheries ...... sustainability in the Lake Victoria basin: an ... Management of large Rivers for Fisheries,.

  17. Fiches techniques Les triacylglycérols des huiles de graines de quatre Cucurbitacées tropicales des genres Lagenaria et Luffa

    Directory of Open Access Journals (Sweden)

    Grondin Isabelle

    2002-03-01

    Full Text Available Les huiles de graines de quatre Cucurbitacées tropicales de l’île de la Réunion, provenant respectivement de deux variétés de l’espèce Lagenaria leucaritha (calebasses bouteille et la gale et de deux espèces du genre Luffa (pipangailles lisse et à côtes, ont été analysées aussi bien pour la fraction saponifiable que pour la fraction insaponifiable. L’étude de la fraction saponifiable a été consacrée, d’une part, à la détermination de la composition quantitative et qualitative en acides gras des différentes huiles dont les résultats ont fait l’objet d’une publication antérieure [1] et, d’autre part, à celle de leurs triacylglycérols. Une comparaison des compositions en acides gras des deux genres étudiés a permis de mettre en évidence les spécificités propres à chaque genre. Les genres Lagenaria et Luffa, présentant une composition en acides gras qualitativement similaire, contiennent ainsi les AG couramment rencontrés dans le règne végétal, à savoir les acides palmitique, stéarique, oléique et linoléique. Ce dernier est, par ailleurs, l’acide gras majoritaire avec des teneurs supérieures à 50%. La présence de cet acide gras essentiel confère ainsi à ces huiles de bonnes propriétés diététiques et nutritionnelles. Au sein du genre Lagenaria, les huiles des graines des variétés bouteille et la gale se caractérisent par leur teneur élevée en acide linoléique (71,5% pour la variété bouteille, et 81,5% pour la variété la gale. Les huiles de Lagenaria leucaritha sont du type palmitique-linoléique car ces deux acides gras représentent quantitativement plus de 85% des AG totaux. Contrairement à ces deux huiles, celles du genre Luffa se différencient, d’une part, par une teneur moindre en acide linoléique avec 55,3% pour l’espèce Luffa acutangula et 51,2% pour l’espèce Luffa cylindrica. D’autre part, elles sont du type palmitique-oléique-linoléique puisque ces trois

  18. Mathematical Model and Artificial Intelligent Techniques Applied to a Milk Industry through DSM

    Science.gov (United States)

    Babu, P. Ravi; Divya, V. P. Sree

    2011-08-01

    The resources for electrical energy are depleting and hence the gap between the supply and the demand is continuously increasing. Under such circumstances, the option left is optimal utilization of available energy resources. The main objective of this chapter is to discuss about the Peak load management and overcome the problems associated with it in processing industries such as Milk industry with the help of DSM techniques. The chapter presents a generalized mathematical model for minimizing the total operating cost of the industry subject to the constraints. The work presented in this chapter also deals with the results of application of Neural Network, Fuzzy Logic and Demand Side Management (DSM) techniques applied to a medium scale milk industrial consumer in India to achieve the improvement in load factor, reduction in Maximum Demand (MD) and also the consumer gets saving in the energy bill.

  19. Materials of All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection

    International Nuclear Information System (INIS)

    1998-01-01

    The All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection is cyclic (in 3 year period) conference being a broad review of state of art and development of all nuclear branches cooperated with industry and other branches of national economy and public life in Poland. The conference has been divided in one plenary session and 8 problem sessions as follow: Radiation technologies of flue gas purification; radiation technologies in food and cosmetic industry; application of nuclear techniques in environmental studies and earth science; radiometric methods in material engineering; isotope tracers in biological studies and medical diagnostics; radiometric industrial measuring systems; radiation detectors and device; nuclear methods in cultural objects examination. The poster section as well as small exhibition have been also organised

  20. De la fiche technique « producteur » au cahier des charges « utilisateur »

    Directory of Open Access Journals (Sweden)

    Vigneron Pierre-Yves

    2005-09-01

    Full Text Available Production of refined or flavored vegetable oils requires to be close to the expectations of the customers (industry, catering, consumers. From technical data established by the producer taking into account his own constraints and the products characteristics, appropriate specifications are set up. The document includes different parts such as technical information concerning the raw material, the final product, the packaging but also the procedures and the organisation to insure the quality of the product along the process. More over, the producer must pay attention to the specific request from the consumers; this includes nutritional information, safety insurance, advices about uses and storage conditions. To provide efficient answers, the producer has to build up preliminary files conducted by R&D. This policy is all the more necessary because the producer promotes commercial brands.

  1. Des terres pour l’agro-industrie internationale ? Un dilemme pour la politique foncière malgache

    Directory of Open Access Journals (Sweden)

    André Teyssier

    2010-02-01

    Full Text Available Les manœuvres d’appropriation foncière à grande échelle tentées fin 2008 par les entreprises Daewoo Logistics et Varun International, largement relayées par les médias et dénoncées par diverses organisations, ont participé à la déstabilisation du gouvernement Ravalomanana. Les montages de ces deux grands projets agro-industriels ont suivi des trajectoires différentes, l’un choisissant de contrôler d’immenses superficies par bail emphytéotique, l’autre privilégiant des formes de contractualisation de la production, mais tous deux ont été abandonnés face à des mouvements de contestation basés sur l’inaliénabilité de la « terre des ancêtres ». Le rejet de ces projets d’envergure encore inédite et en partie tournés vers des cultures d’exportation est compréhensible tant les retombées économiques et sociales paraissaient incertaines. Madagascar ne saurait néanmoins se priver d’investissements dans le secteur agricole, mais des choix de développement, orientés par une meilleure connaissance des processus en cours, restent à opérer en toute transparence, afin de combiner développement de l’agro-business et promotion des exploitations familiales. Pour l’instant, ces incertitudes marquent une politique foncière qui, même rénovée, hésite entre la formalisation de droits sur le sol au profit du plus grand nombre grâce à une décentralisation de la gestion foncière et l’octroi de vastes espaces à des firmes internationales suivant des procédures accélérées.

  2. Technology transfer of nuclear techniques and nucleonic control systems in the mineral industry

    International Nuclear Information System (INIS)

    1990-11-01

    Among the many beneficial applications of radiation and radioisotopes in industry which are now well established in advanced countries, the applications of nuclear techniques and nucleonic control systems in the mineral industry have great potential for developing Member States. The use of nucleonic on-stream analyzers in the coal industry has resulted in enormous technical and economic benefits in addition to minimization of environmental pollution. Large savings have also resulted from the use of such analyzers in the processing of other minerals. Nuclear borehole logging techniques have demonstrated great potential in oil and gas evaluation. Radiotracer investigations have led to process optimisation and trouble shooting in various stages in ore processing and metallurgy. Though the technical and economic benefits of applications of nuclear techniques in the mineral industry are well recognised, technology transfer in these areas has been hampered by a variety of factors. In order to review the status and trends in nuclear techniques and nucleonic control systems in the mineral industry and the problems and considerations in their technology transfer to developing Member States, the IAEA convened an Advisory Group Meeting in Bombay, India, 15-19 January 1990. The present publication is based on the 7 contributions presented at this meeting. A separate abstract was prepared for each of these papers. Refs, figs and tabs

  3. Methodological guide: management of industrial sites potentially contaminated by radioactive substances; Guide methodologique: gestion des sites industriels potentiellement contamines par des substances radioactives

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    At the request of the Ministries of Health and the Environment, IPSN is preparing and publishing the first version of the methodological guide devoted to managing industrial sites potentially contaminated by radioactive substances. This guide describes a procedure for defining and choosing strategies for rehabilitating such industrial sites. (author)

  4. Addressing safety issues through a joint industry programme; Traiter des problemes de securite a travers un programme industriel commun

    Energy Technology Data Exchange (ETDEWEB)

    Pool, G.; Williams, T.P. [BG Technology (United Kingdom); Jones, A.M. [Health and Safety Executive (United Kingdom)

    2000-07-01

    In an increasingly fragmented gas market, the focus for national gas safety may not rest with one major utility or gas supplier but may be spread across many companies. There will also be many new organisations in a liberalized gas industry with varying views on the needs and benefits of safety related technology development but all agree there is a need to ensure that the good safety record of gas as a domestic fuel is maintained. The number of carbon monoxide (CO) incidents is not decreasing significantly despite an increased awareness of the problem. As a consequence, a two-year joint industry programme addressing issues related to carbon monoxide has been established, co-ordinated by BG Technology and supported by gas organisations, government agencies, manufacturers and suppliers across Europe and the World. The 2-year 2 pound million programme has been constructed as twelve separate projects addressing issues such as the reporting and analysis of domestic incidents, improved service or installation practice, CO alarm reliability and information dissemination. The paper gives results and achievements of the programme, through new techniques, standards, procedures or equipment and demonstrates how the gas industry can work together to meet common safety objectives. (authors)

  5. La production des oléfines. Etat de la technique et développement dans le domaine des réacteurs chimiques et des procédés Olefin Production. State of Technology and Developement in the Field of Chemical Reactors and Processes

    Directory of Open Access Journals (Sweden)

    Amouyal R.

    2006-11-01

    Full Text Available La production des oléfines légères : éthylène, propylène et butadiène est actuellement entièrement basée sur le vapocraquage d'hydrocarbures dans des fours tubulaires. L'industrie doit faire face à un problème de coûts de production croissants, en grande partie dû au renchérissement des hydrocarbures et de l'énergie. D'autres procédés que le vapocraquage ont été proposés pour favoriser la diversification sur le plan des matières premières ; certains ont même été exploités industriellement. Le présent article fait le point sur l'état des développements en cours concernant plus particulièrement les procédés suivants : - craquage autothermique ; - craquage par caloporteur solide ; - craquage cyclique ; - craquage catalytique ; - prétraitement de charges lourdes ; - oléfines à partir de gaz de synthèse ; - oléfines à partir de biomasse. The production of light olefins (ethylene, propylene and butadien is now based entirely on hydrocarbon steam cracking in pipe stills. The industry must face the problem of increasing production costs, largely due to the higher costs of hydrocarbons and energy. Processes other than steam cracking have been proposed to promote diversification with regard to raw materials, and some such processes have even operated industrially. This article sums up the state of ongoing developments concerning in particular the following processes: a autothermal cracking; b cracking by a solid heat carrier; c cyclic cracking; d catalytic cracking ; e preprocessing of heavy feeds; f olefins from synthetic gas; g olefins from biomass.

  6. Les médiations sociales, culturelles et technologiques dans la production et l’appropriation des intergiciels de l’industrie du jeu vidéo au Canada

    OpenAIRE

    Charrieras, Damien

    2011-01-01

    Le secteur industriel des intergiciels de jeux vidéo (game middleware) est très lié au développement des industries du jeu vidéo dans lequel le Canada est très actif et dont l’importance économique ne cesse de croître. Dans son étude du rôle des industries de l’intergiciel dans la filière de production d’un jeu vidéo l’auteur s'est penché sur la circulation des intergiciels de jeux vidéo pour explorer les multiples relations existantes entre les sociétés d’intergiciel, les entreprises de déve...

  7. Nuclear analytical techniques for on-line elemental analysis in industry

    International Nuclear Information System (INIS)

    1988-06-01

    This report is the result of an advisory group meeting held in Espoo, Finland, 1-5 June, 1987. The purpose of the meeting was to assess the present status and development of nuclear analytical techniques used for industrial process control. The report gives an overview of the different nuclear techniques used for process control and the most important applications. A separate abstract was prepared for each of the 7 papers presented at the meeting. Refs, figs and tabs

  8. L’IMPACT DE L’APPLICATION DES REFORMES BALE III SUR L’INDUSTRIE BANCAIRE ROUMAINE

    Directory of Open Access Journals (Sweden)

    Maria Halep

    2012-12-01

    Full Text Available Le début du XXIème a connu un essor remarquable des marchés financiers, de l’innovation et des processus de déréglementation. L’inflation faible, la liquidité abondante, la confiance dans les marchés efficaces et autorégulateurs ont conduit à une perception généralisée de risque faible, incitant les acteurs à une prise accrue de risque. Face aux crises qui s’enchaînent depuis maintenant cinq ans, des mesures de ré-réglementation du système ont été proposées, communément appelées Reformes de Bâle.L’article analyse l’évolution des recommandations de Bâle en lien avec l’évolution économique et des marchés financiers et évalue l’impact de ces dernières sur le secteur bancaire roumain.

  9. Industrially relevant Al2O3 deposition techniques for the surface passivation of Si solar cells

    NARCIS (Netherlands)

    Schmidt, J.; Werner, F.; Veith, B.; Zielke, D.; Bock, R.; Tiba, M.V.; Poodt, P.; Roozeboom, F.; Li, A.; Cuevas, A.; Brendel, R.

    2010-01-01

    We present independently confirmed efficiencies of 21.4% for PERC cells with plasma-assisted atom-ic-layer-deposited (plasma ALD) Al2O3 rear passivation and 20.7% for cells with thermal ALD-Al2O3. Additionally, we evaluate three different industrially relevant techniques for the deposition of

  10. Forging Harmony in the Social Organism: Industry and the Power of Psychometric Techniques

    Science.gov (United States)

    Herman, Frederik

    2014-01-01

    This article analyses the initiating role of the steel industry in educational selection by means of psychometric techniques used in the psycho-physiological laboratory associated with a vocational school in Luxembourg founded in 1914. It first considers the origins of, and initial meanings bestowed upon, this first (and perhaps also last)…

  11. Formalisation d'un modèle de conception et d'innovation dans le domaine des bio-industries : cas des particules d'argile.

    OpenAIRE

    Lorentz , Romain

    2014-01-01

    This doctoral thesis was realized within the framework of a partnership between the Product Design and Innovation Laboratory of Arts et Métiers ParisTech and the Ecole de Biologie Industrielle. The research project behind our thesis aims to support the promotion of new clay particles having been patented by the EBInnov® laboratory. This new polyfunctional ingredient is designed to satisfy several applications in the bio-industries, including the pharmaceutical and cosmetic industry, the phyto...

  12. Gamma, X-ray and neutron techniques for the coal industry

    International Nuclear Information System (INIS)

    1986-01-01

    Nuclear techniques play a prominent role in all aspects of the coal industry, from exploration through mine development to testing of coal quality during production. The advent of on-line nuclear techniques allows continuous, near real time appraisal of coal quality free from the errors inherent in conventional techniques based on discrete samples. The Advisory Group Meeting reviews the latest developments in this area and makes recommendations on the most promising areas and priorities for future research and development activities. This report records the proceedings of the Advisory Group Meeting. Separate abstracts were prepared for each of the 13 papers in this report

  13. Nuclear techniques in the coal industry. Proceedings of a final research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    With the aim of promoting advanced research and facilitating a more extensive application of nuclear techniques for environmental protection in the exploration and exploitation of coal, the IAEA established the present co-ordinated research programme (CRP) in 1989. This report includes an assessment of the current status and trends in nuclear techniques in the coal industry and the results obtained by the participants at the CRP. Proceedings of the final CRP on ``Nuclear Techniques in Exploration and Exploitation of Coal: On-line and Bulk Analysis and Evaluation of Potential Environmental Pollutants in Coal and Coke``, was held in Krakow, Poland, from 9 to 12 May 1994. Refs, figs, tabs.

  14. Bois-Noirs ore. Recovery of uranium of solutions from acid treatment. Results of industrial tests at the Gueugnon plant; Minerai des Bois-Noirs. Recuperation de l'uranium des solutions d'attaques acides. Resultats des essais industriels effectues a l'usine de Gueugnon

    Energy Technology Data Exchange (ETDEWEB)

    Le Bris, J

    1959-04-01

    Industrial-scale tests are reported of the efficiency of two recovery processes for the separation of uranium from sulfuric acid pickling solutions used on ore from Bois-Noirs, at the Gueugnon works. The final stage of each process is sodium uranate. The earlier part of the report deals with tests of the separation of uranium from foreign metals by fractional precipitation. The second part deals with the separation of uranium from these metals by carbonation of the solutions. (author) [French] Le present rapport concerne les essais industriels de deux procedes de recuperation de l'uranium de solutions d'attaque sulfurique du minerai des Bois-Noirs a l'usine de Gueugnon. Le stade final pour ces deux procedes etant l'uranate de sodium, une premiere partie est consacree aux essais de separation de l'uranium des metaux etrangers par precipitation fractionnee; une deuxieme partie est consacree aux essais de separation de l'uranium des metaux etrangers par carbonatation des solutions d'attaque du minerai. (auteur)

  15. Internet et la recomposition territoriale des relations dans l'agriculture suisse

    OpenAIRE

    Gigon, Nathalie; Crevoisier, Olivier

    2015-01-01

    L'agriculture et l'industrie agro-alimentaire suisses se transformed très rapidement. À un monde industrial fonctionnant à l'échelle nationale et basé sur des normes techniques succède un monde domestique basé sur l'identité régionale et les relations interpersonnelles. L'utilisation d'Internet devrait participer à la recomposition des relations entre producteurs et consommateurs et refléter les transformations territoriales qu'elles impliquent. Or les sites Internet de promotion des produits...

  16. Ageing Mechanisms and Control. Specialists’ Meeting on Life Management Techniques for Ageing Air Vehicles (Les mecanismes vieillissants et le controle) (Reunions des specialistes des techniques de gestion du cycle de vie pour vehicules aeriens vieillissants)

    Science.gov (United States)

    2003-02-01

    Synthèse Aujourd’hui, les chefs militaires de l’ensemble des pays membres de l’OTAN constatent que leurs flottes d’aéronefs sont maintenues en exploitation...problems and, where possible, the investment required for attaining the needed capability. Thème Aujourd’hui, les chefs militaires de l’ensemble des pays...25.13091 identifies risk requirements and its companion Advisory Circular (AC 25.1309) interprets those requirements as the familiar 10-9 probability

  17. Dosimetry techniques of thermal neutrons and {gamma} radiation in reactor cores; Techniques de dosimetrie des neutrons thermiques et du rayonnement {gamma} dans les piles

    Energy Technology Data Exchange (ETDEWEB)

    Sutton, J; Draganic, I; Hering, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    Chemical studies under radiation done in the reactor cores require to be followed by dosimetry. When the irradiations are done in the reflector, one can limit to the measure of the {gamma} and the neutron radiation. For the dosimetry of the {gamma} radiation, a dosimeter of ferrous sulfate is convenient until doses of about 10{sup 6} rep. The use of aired oxalic acid solutions permits to reach 10{sup 7} rep. The dosimetry of thermal neutrons has been made with solutions of cobalt sulphate or paper filter impregnated with this salt. The total chemical effect of the {gamma} and of the slow neutrons radiation is obtained with solutions of ferrous sulfate added with lithium sulphate. (M.B.) [French] Les etudes de chimie sous radiation faites dans les piles exigent d'etre suivies par dosimetrie. Lorsque les irradiations sont effectues dans le reflecteur, on peut se limiter a doser le rayonnement {gamma} et les neutrons. Pour la dosimetrie du rayonnement {gamma}, un dosimetre a sulfate ferreux convient jusqu'a des doses d'environ 10{sup 6} rep. L'emploi de solutions aerees d'acide oxalique permet d'atteindre 10{sup 7} rep. La dosimetrie des neutrons thermiques a ete faite avec des solutions de sulfate de cotalt ou du papier filtre impregne de ce sel. L'effet chimique total du rayonnement {gamma} et des neutrons lents est obtenu avec des solutions de sulfate ferreux additionne de sulfate de lithium. (M.B.)

  18. Molecular identification of peste des petits ruminants virus in wild goat and domestic small ruminants by real-time -PCR technique in Erbil-Iraq

    Directory of Open Access Journals (Sweden)

    E.P. Candlan

    2017-06-01

    Full Text Available In July 2010 outbreak was occurred in wild goat in Barzan, Sherwin mizzen and Mergasur in Kurdistan Region- Iraq. There were over 2700 deaths (both young and adult during the period of July 2010 to October 2011. Based on the clinical signs and post-mortem findings, the involvement of peste des petits ruminants virus (PPRV was suspected. This was confirmed by Real Time PCR technique using TaqMan®probes for the detection of Peste des petits ruminants. The results of Real-Time PCR for the 9 sample taken from 9 Wild goat there are 6 sample positive and 3 sample negative and 76 sample from domestic ruminants (sheep and goat 63 samples was negative for PPR. This result confirms the diagnosis domestic ruminants in the region are routinely vaccinated with an attenuated vaccine based on the ‘Nigeria/75/1’ strain of PPRV.

  19. National symposium: nuclear technique in industry, medicine, agriculture and environment protection. Abstracts of papers

    International Nuclear Information System (INIS)

    1995-01-01

    The National Symposium 'Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection' has been held in Rynia near Warsaw from 24 to 27 April 1995. Totally 94 lectures have been presented. The actual state of art in Polish investigations have been shown in all branches of applied nuclear sciences. The plenary session devoted to general topics has began the symposium. Further conference has been divided into 18 subject sessions. There were: 1) radiation technologies in environment protection; 2) radiation technologies in materials engineering; 3) radiation preservation in food; 4) radiation techniques for medical use; 5) radiotracers in industrial investigations; 6) radiotracers in water and sewage management and leak control; 7) tracers in hydrology; 8) radiotracers in materials testing; 9) instruments for environment protection, 10) radiometric industrial gages; 11) diagnostic and testing instruments; 12) application of nuclear techniques in materials testing; 13) applications of nuclear techniques in geology and hydrogeology; 14) radioanalytical methods; 15) radiation detectors; 16) radiation measurements; 17) data processing from radiometric experiments; 18) accelerators, isotopes manufacturing, INIS

  20. Dismantling of nuclear facilities: the industrial know-how; Demantelement des installations nucleaires: les voies de la maitrise industrielle

    Energy Technology Data Exchange (ETDEWEB)

    Lellament, R. [Societe Francaise d' Energie Nucleaire (SFEN), Groupe de Reflexion Energie/Environnement, 75 - Paris (France)

    2004-11-01

    Numerous nuclear facilities in laboratories or research reactors have been decommissioned and dismantled over the 2 last decades throughout the world. The valuable feedback experience has allowed nuclear industry to design, upgrade and test specific techniques for dismantling. These techniques are efficient although they have been validated on a reduced number of nuclear power plants. In France only 3 power units have been dismantled: Chinon A1, A2 and Brennilis (EL4) and they are not representative of the real park of EDF'reactors. 6 PWR-type reactors have already been dismantled in the Usa. The results of a survey concerning 26 countries shows that the dismantling cost is around 320 dollars/kWe, it represents 15% of the construction cost which is far from being excessive as it is often read in the media. The dismantling costs can be broken into: - de-construction (25-55%), - wastes from dismantling (17-43%), - security and monitoring (8-13%), - site reclamation (5-13%), and - engineering and project management (5-24%). (A.C.)

  1. Le management des risques de l'entreprise cadre de référence, techniques d'application

    CERN Document Server

    Committee of sponsoring organizations of the Treadway commission (Etats-Unis)

    2005-01-01

    Traduction en français du second rapport COSO, ce livre est un véritable outil pour les dirigeants confrontés à la complexité opérationnelle du management des risques. Adaptable à toutes les organisations, il constitue un socle méthodologique indispensable pour tous les professionnels de la gestion des risques ainsi que pour les auditeurs et consultants internes et externes. Il est également un manuel incontournable pour les étudiants et les enseignants. Dans un environnement économique fortement concurrentiel et en constante évolution, cet ouvrage ne s'intéresse pas uniquement à la gestion des risques mais contribue aussi à identifier puis exploiter les opportunités nouvelles, source d'avantages concurrentiels.

  2. L'épistémologie et l'histoire des sciences et des techniques peuvent elles aider les futurs enseignants de sciences physiques dans l'exercice de leur métier ? Regards portés pour une ingénierie de formation

    Directory of Open Access Journals (Sweden)

    Guedj Muriel

    2014-01-01

    Full Text Available Cette étude interroge la place de l'Epistémologie, l'Histoire des Sciences et des Techniques comme élément pertinent pour améliorer la professionnalité des enseignants de sciences physiques. La réflexion se nourrit des nouvelles orientations prises au sein d'écoles d'ingénieurs et de facultés de médecine qui ont fait le choix d'introduire des unités d'enseignement dédiées aux Sciences Humaines et Sociales afin de perfectionner la qualité professionnelle de leurs formations. Une étude de cas dédiée à l'enseignement de l'énergie illustre le propos.

  3. A comparison of three observational techniques for assessing postural loads in industry.

    Science.gov (United States)

    Kee, Dohyung; Karwowski, Waldemar

    2007-01-01

    This study aims to compare 3 observational techniques for assessing postural load, namely, OWAS, RULA, and REBA. The comparison was based on the evaluation results generated by the classification techniques using 301 working postures. All postures were sampled from the iron and steel, electronics, automotive, and chemical industries, and a general hospital. While only about 21% of the 301 postures were classified at the action category/level 3 or 4 by both OWAS and REBA, about 56% of the postures were classified into action level 3 or 4 by RULA. The inter-method reliability for postural load category between OWAS and RULA was just 29.2%, and the reliability between RULA and REBA was 48.2%. These results showed that compared to RULA, OWAS, and REBA generally underestimated postural loads for the analyzed postures, irrespective of industry, work type, and whether or not the body postures were in a balanced state.

  4. Classification of rabbit meat obtained with industrial and organic breeding by means of spectrocolorimetric technique

    Science.gov (United States)

    Menesatti, P.; D'Andrea, S.; Negretti, P.

    2007-09-01

    Rabbit meat is for its nutritional characteristics a food corresponding to new models of consumption. Quality improvement is possible integrating an extensive organic breeding with suitable rabbit genetic typologies. Aim of this work (financed by a Project of the Lazio Region, Italy) was the characterization of rabbit meat by a statistic model, able to distinguish rabbit meat obtained by organic breeding from that achieved industrially. This was pursued through the analysis of spectral data and colorimetric values. Two genetic typologies of rabbit, Leprino Viterbese and a commercial hybrid, were studied. The Leprino Viterbese has been breeded with two different systems, organic and industrial. The commercial hybrid has been bred only industrially because of its characteristics of high sensibility to diseases. The device used for opto-electronic analysis is a VIS-NIR image spectrometer (range: 400-970 nm). The instrument has a stabilized light, it works in accordance to standard CIE L*a*b* technique and it measures the spectral reflectance and the colorimetric coordinates values. The statistic data analysis has been performed by Partial Least Square technique (PLS). A part of measured data was used to create the statistic model and the remaining data were utilized in phase of test to verify the correct model classification. The results put in evidence a high percentage of correct classification (90%) of the model for the two rabbit meat classes, deriving from organic and industrial breeding. Moreover, concerning the different genetic typologies, the percentage of correct classification was 90%.

  5. TECHNIQUE OF AN ASSESSMENT OF COMPETITIVENESS OF THE ENTERPRISES OF THE FURNITURE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Vitaliy A. Zhigarev

    2015-01-01

    Full Text Available The purpose of this article is the description of an author’s technique of an assessment of competitiveness of the enterprises of the furniture industry which mainobjective is the economic assessment ofproduction efficiency of production of thefurniture enterprise, an assessment ofthe intra firm making production efficiencyof furniture, identification of the factors influencing overall performance of thefurniture enterprise.

  6. Handbook of software quality assurance techniques applicable to the nuclear industry

    Energy Technology Data Exchange (ETDEWEB)

    Bryant, J.L.; Wilburn, N.P.

    1987-08-01

    Pacific Northwest Laboratory is conducting a research project to recommend good engineering practices in the application of 10 CFR 50, Appendix B requirements to assure quality in the development and use of computer software for the design and operation of nuclear power plants for NRC and industry. This handbook defines the content of a software quality assurance program by enumerating the techniques applicable. Definitions, descriptions, and references where further information may be obtained are provided for each topic.

  7. Handbook of software quality assurance techniques applicable to the nuclear industry

    International Nuclear Information System (INIS)

    Bryant, J.L.; Wilburn, N.P.

    1987-08-01

    Pacific Northwest Laboratory is conducting a research project to recommend good engineering practices in the application of 10 CFR 50, Appendix B requirements to assure quality in the development and use of computer software for the design and operation of nuclear power plants for NRC and industry. This handbook defines the content of a software quality assurance program by enumerating the techniques applicable. Definitions, descriptions, and references where further information may be obtained are provided for each topic

  8. An example of the use of the DELPHI method: future prospects of artificial heart techniques in France; Un exemple d'utilisation de la methode DELPHI: perspectives de developpement en France des techniques de coeur artificiel

    Energy Technology Data Exchange (ETDEWEB)

    Derian, Jean-Claude [Commissariat a l' energie atomique et aux energies alternatives - CEA, Centre d' Etudes Nucleaires de Fontenay-aux-Roses, Departement des Programmes, Section des Etudes Economiques Generales (France); Morize, Francoise [Commissariat a l' energie atomique et aux energies alternatives - CEA, Centre d' Etudes Nucleaires de Saclay, Institut National des Sciences et Techniques Nucleaires (France); Vernejoul, Pierre de [Faculte de Medecine Necker - Enfants Malades (France); Service Hospitalier Frederic Joliot (France); Vial, Renee [Direction de Protection et Surete Radiologiques (France)

    1971-07-01

    The artificial heart is still only a research project surrounded by numerous uncertainties which make it very difficult to estimate, at the moment, the possibilities for future development of this technique in France. A systematic analysis of the hazards which characterize this project has been undertaken in the following report: restricting these uncertainties has required a taking into account of opinions of specialists concerned with type of research or its upshot. We have achieved this by adapting an investigation technique which is still unusual in France, the DELPHI method. This adaptation has allowed the confrontation and statistical aggregation of the opinions given by a body of a hundred experts who were consulted through a program of sequential interrogations which studied in particular, the probable date of the research issue, the clinical cases which require the use of an artificial heart, as well as the probable future needs. After having taken into account the economic constraints, we can deduce from these results the probable amount of plutonium 238 needed in the hypothesis where isotopic generator would be retained for the energetics feeding of the artificial heart [French] Le coeur artificiel n'est encore actuellement qu'un projet de recherche auquel sont attachees de nombreuses incertitudes qui rendent difficile l'appreciation des possibilites de developpement futures de cette technique en France. Une analyse systematique des aleas qui caracterisent ce projet est entreprise dans l'etude ci-apres: circonscrire ces aleas necessite la prise en compte d'opinions emanant des specialistes concernes par cette recherche ou par son issue: c'est ce qui a ete realise en adaptant une methodologie non classique en France, la methode DELPHI. Cette adaptation a permis la confrontation et l'agregation statistique des opinions fournies par un college d'une centaine d'experts consultes par un programme d'interrogations sequentielles, envisageant en particulier les

  9. Une installation expérimentale pour l'étude du traitement par combustion des fumées industrielles An Experimental Plant for Processing Industrial Fumes by Combustion

    Directory of Open Access Journals (Sweden)

    Morillon R.

    2006-11-01

    Full Text Available Le rejet à l'atmosphère d'effluents gazeux d'origine industrielle entraîne un accroissement sensible de la pollution atmosphérique ; en outre, il s'accompagne souvent d'une perte d'énergie lorsque l'élément polluant est un hydrocarbure. Dans ce cas, l'utilisation du gaz naturel pour le traitement par combustion des fumées industrielles apporte une solution élégante et souvent peu coûteuse grâce à la récupération d'énergie qu'il est possible de faire. La première partie de l'article rappelle les aspects théoriques de ce traitement ; en particulier, l'influence des divers éléments sur son efficacité y est discutée (composition de l'atmosphère polluée, température, temps de séjour, etc.. II apparaît ainsi que diverses conditions doivent être remplies simultanément pour obtenir une efficacité satisfaisante. Afin de disposer d'éléments d'ingénierie permettant de construire les unités de traitement les plus efficaces et les plus sûres possible, au coût le plus bas possible, la Direction des études et techniques nouvelles du Gaz de France a réalisé une installation expérimentale qui est présentée dans la deuxième partie de l'article. Enfin, quelques examples d'utilisation de cette installation expérimentale, qui constitue un nouvel outil de travail mis à la disposition des utisitateurs et des constructeurs, sont décrits dans la troisième partie de l'article. The discharge into the atmosphere of industrial waste gases causes substantially increased air pollution. Moreover, it is often accompanied by loss of energy when the polluting element is a hydrocarbon. In such cases, the use of natural gas for processing industrial fumes by combustion provides an elegant solution, which moy often prove economical too becouse of the recovery of energy it makes possible. The first part of this article reviews the theoretical aspects of such processing. The way in which its effectiveness is affected by various parameters

  10. Le « bassin des carènes » et le service technique des constructions navales à Balard : un exemple de cité scientifique à Paris

    Directory of Open Access Journals (Sweden)

    Valérie Gaudard

    2009-05-01

    Full Text Available Le « bassin des carènes » à Balard abrite un ensemble cohérent d’édifices techniques, scientifiques et administratifs destinés à l’étude du comportement des navires et de leur propulsion en toutes situations. Créé à l’initiative de l’ingénieur Bertin et inauguré en 1906, le premier bassin, en béton, comptait alors parmi les quatre plus grands bassins du monde. À partir de 1932, Perret frères édifient une véritable cité scientifique : bâtiment administratif (IMH 1965, laboratoires, plusieurs bassins sont élevés en béton armé, avec un même soin accordé à l’ensemble.The ‘bassin des carènes’, the ship testing tank situated at Balard, in Paris, comprises a coherent ensemble of technical , scientific and administrative buildings devoted to the study of ships and their propulsion in different situations. The facility was first created in 1906 at the instigation of the engineer Bertin. At this date, the towing tank, constructed in reinforced concrete, was one of the four largest in the world. From 1932, the Perret brothers were commissioned to provide other constructions, completing an authentic scientific complex or ‘city’. This included the administrative building (given historic monument protection in 1932 and several other tanks, all constructed in reinforced concrete and with the same attention to detail.

  11. Sur la prise en compte du mode de financement dans les calculs de rentabilité. La méthode des intérêts seulement déductibles Financing Mix and Capital Budgeting Techniques. the Shadow Interest Method

    Directory of Open Access Journals (Sweden)

    Babusiaux D.

    2006-11-01

    Full Text Available La pratique des calculs de rentabilité avec shadow interest se développe depuis quelques années dans les entreprises pétrolières, principalement dans le secteur exploration et développement des gisements. L'objet de cet article est de replacer cette approche parmi les méthodes classiques (calculs de rentabilité globale et de rentabilité des capitaux propres. Une relation simple entre les revenus actualisés relatifs à chacune des approches est obtenue sous certaines hypothèses simplificatrices. Capital budgeting techniques with shadow interesthave been gaining credence in the petroleum industry in recent years, particularly in the oil-field prospection and development sector. The aim of this article is to situate this approach among conventional methods (overall return and return on equity. A simple relation between net present value concerning each approach is obtained provided some simplifying assumptions are made.

  12. À la croisée des univers du transmedia, de la marque et de la franchise dans l’industrie cinématographique

    Directory of Open Access Journals (Sweden)

    Hélène Laurichesse

    2012-06-01

    Full Text Available La montée en puissance de la stratégie de marque et celle de la création transmedia dans les industries créatives nous a conduits à questionner les relations à établir entre ces deux tendances assez systématiquement associées dans la littérature. Sont-elles finalement indépendantes ou interdépendantes ? Nous verrons ainsi que la marque dans le secteur cinématographique n’est pas nécessairement transmedia, mais que la création transmedia s’inscrit de manière plus évidente et plus aboutie que les autres œuvres dans une logique de marque. Nous définirons ce qu’est la franchise transmedia et envisagerons son rapport au commercial. En générant des revenus supplémentaires au-delà des formes d'exploitations traditionnelles, elle représente aujourd’hui le modèle économique qui conduit à la performance. L’analyse des meilleures performances au box-office nous permettra d’apprécier sur un corpus de 126 franchises, cette forme d’efficacité.The escalation of brand strategy and transmedia narratives in the creative industries drove us to focus on the interaction between these two trends consistently associated in the previous studies. Are they actually independent or interrelated? We will show that branding in the motion picture industry doesn’t necessarily take a transmedia form, but the transmedia narrative is the more obvious and achieved way to build a brand. We will define the transmedia franchise and examine its commercial side. By generating additional revenues beyond traditional forms of exploitation, the franchise now embodies the economic model leading to financial performance. Box-office analysis will allow us to evaluate this efficiency based on a panel of 126 franchises source studies.

  13. Nuclear techniques for on-line analysis in the mineral and energy industries

    International Nuclear Information System (INIS)

    Sowerby, B.D.; Watt, J.S.

    1994-01-01

    Nuclear techniques are the basis of many on-line analysis systems which are now widely used in the mineral and energy industries. Some of the systems developed by the CSIRO depend entirely on nuclear techniques; others use a combination of nuclear techniques and microwave, capacitance, or ultrasonic techniques. The continuous analysis and rapid response of these CSIRO systems has led to improved control of mining, processing and blending operations, with increased productivity valued at A$50 million per year to Australia, and $90 million per year world wide. This paper reviews developments in nuclear on-line analysis systems by the On-Line Analysis Group in CSIRO at Lucas Heights. Commercialised systems based on this work analyse mineral and coal slurries and determine the ash and moisture contents of coal and coke on conveyors. This paper also reviews two on-line nuclear analysis systems recently developed and licensed to industry, firstly for the determination of the mass flow rates of oil/water/gas mixtures in pipelines, and secondly for determination of the moisture, specific energy, ash and fouling index in low rank coals. 8 refs., 3 tabs., 4 figs

  14. Application and benefits to industry of radioisotope tracer techniques - an overview

    International Nuclear Information System (INIS)

    Hills, A.E.

    2002-01-01

    Radioisotopes continue to play an important role in better management of natural resources and industrial processes. The success of radioisotope applications is primarily to the ability, conferred by the unique properties of radioactive materials, to collect data, which cannot be obtained by other investigative techniques. Radioisotope-based industrial tracer techniques that have stood the test in their own right are described briefly and certain of the economic and process efficiency impacts are highlighted. The financial and other benefits of this technology, especially in Petrochemical sector have been amply demonstrated and accepted. Typical techniques employed are: Gamma ray scanning of distillation columns, leak testing of heat exchangers, deposit and blockage detection in pipe lines, homogeneous mixing, flow rate measurements and liquid interface measurements. The financial benefits by these techniques are widely accepted to exceed the cost of equipment and studies by several folds. Based on retrospective analysis of the data, it is found that an average cost-benefit ratio of 1:20 in many applications is reasonably representative. (Author)

  15. Industrial scale production of stable isotopes employing the technique of plasma separation

    International Nuclear Information System (INIS)

    Stevenson, N.R.; Bigelow, T.S.; Tarallo, F.J.

    2003-01-01

    Calutrons, centrifuges, diffusion and distillation processes are some of the devices and techniques that have been employed to produce substantial quantities of enriched stable isotopes. Nevertheless, the availability of enriched isotopes in sufficient quantities for industrial applications remains very restricted. Industries such as those involved with medicine, semiconductors, nuclear fuel, propulsion, and national defense have identified the potential need for various enriched isotopes in large quantities. Economically producing most enriched (non-gaseous) isotopes in sufficient quantities has so far eluded commercial producers. The plasma separation process is a commercial technique now available for producing large quantities of a wide range of enriched isotopes. Until recently, this technique has mainly been explored with small-scale ('proof-of-principle') devices that have been built and operated at research institutes. The new Theragenics TM facility at Oak Ridge, TN houses the only existing commercial scale PSP system. This device, which successfully operated in the 1980's, has recently been re-commissioned and is planned to be used to produce a variety of isotopes. Progress and the capabilities of this device and it's potential for impacting the world's supply of stable isotopes in the future is summarized. This technique now holds promise of being able to open the door to allowing new and exciting applications of these isotopes in the future. (author)

  16. Corrosion and alteration of materials from the nuclear industry; La Corrosion et l'alteration des materiaux du nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Beauvy, M.; Berthoud, G.; Defranceschi, M.; Ducros, G.; Feron, D.; Guerin, Y.; Latge, C.; Limoge, Y.; Madic, C.; Santarini, G.; Seiler, J.M.; Vernaz, E.; Richet, C.

    2010-07-01

    The control of the corrosion phenomenon is of prime importance for the nuclear industry. The efficiency and the safety of facilities can be affected by this phenomenon. The nuclear industry has to face corrosion for a large variety of materials submitted to various environments. Metallic corrosion operates in the hot and aqueous environment of water reactors which represent the most common reactor type in the world. Progresses made in the control of the corrosion of the different components of these reactors allow to improve their safety. Corrosion is present in the facilities of the back-end of the fuel cycle as well (corrosion in acid environment in fuel reprocessing plants, corrosion of waste containers in disposal and storage facilities, etc). The future nuclear systems will widen even more the range of materials to be studied and the situations in which they will be placed (corrosion by liquid metals or by helium impurities). Very often, corrosion looks like a patchwork of particular cases in its description. The encountered corrosion problems and their study are presented in this book according to chapters representing the main sectors of the nuclear industry and classified with respect to their phenomenology. This monograph illustrates the researches in progress and presents some results of particular importance obtained recently. Content: 1 - Introduction: context, stakes and goals; definition of corrosion; a complex science; corrosion in the nuclear industry; 2 - corrosion in water reactors - phenomenology, mechanisms, remedies: A - uniform corrosion: mechanisms, uniform corrosion of fuel cladding, in-situ measurement of generalized corrosion rate by electrochemical methods, uniform corrosion of nickel alloys, characterization of the passive layer and growth mechanisms, the PACTOLE code - an integrating tool, influence of water chemistry on corrosion and contamination, radiolysis impact on uniform corrosion; B - stress corrosion: stress corrosion cracking

  17. L’industrie du luxe et la mode : du temps des créateurs au temps des communicants (fin XIXe, fin XXe siècle

    Directory of Open Access Journals (Sweden)

    Marc de Ferrière le Vayer

    2007-05-01

    Full Text Available En un siècle, le secteur de la mode en France a connu un profond bouleversement. D’un monde artisanal doté d’un grand savoir-faire, on est passé progressivement à une activité de grande production s’adressant à un marché de plus en plus large. Ainsi, les grands créateurs, tant dans la haute couture que dans le parfum, ont progressivement été remplacés par des designers touche à tout. Le marketing et la publicité deviennent les maîtres du secteur.Since the 19th century, the sector of French fashion economy has been deeply transformed. From a world of craftmen with a high know-how, it has moved to a world dominated by the industry and the mass market. The creators desappear one after another, and omnipotent designers supersede them. Today the luxury industry is ruled by marketing and advertising.

  18. Planning of decontamination and bleaching of textiles in an industrial cycle; Programmation des operations de decontamination et de blanchissage du linge dans un cycle industriel

    Energy Technology Data Exchange (ETDEWEB)

    Boutot, Pierre; Schipfer, Pierre [Commissariat a l' energie atomique et aux energies alternatives - CEA, Centre de Production de Plutonium de Marcoule, Service de Protection contre les Radiations (France)

    1964-10-15

    This note describes the operational planning for the decontamination and bleaching of textiles (clothes, protections, etc.) worn by personnel, in industrial-type washing machines. Various tests have been conducted with contaminated cotton samples using different cleaning products (and quantities) and various temperature cycles. The performance of the washing cycle (soaking, pre-washing, washing, rinsing) is discussed in terms of decontamination and washing efficiency, textile wear and resistance to shrinkage, whiteness, etc. The experimental washing machine is described [French] Cette etude programme les operations de decontamination et de blanchissage du linge au sein d'un cycle de traitement tel qu'il apparait dans les machines a laver industrielles a fort indice de production. Les echantillons de cotonnade, contamines au moyen de produits de fission, sont de meme nature que le tissu des vetements de protection. En matiere de decontamination les meilleurs resultats sont obtenus apres un trempage faiblement acide et un prelavage au moyen d'un sequestrant. Dans le cadre du blanchissage, seule une lessive industrielle employee dans la phase de lavage peut conferer aux tissus la luminance que requiert leur bonne presentation. Les taches persistantes sont effacees par blanchiment au cours du rincage tiede. Une analyse terminale permet de constater que l'usure des vetements est davantage liee aux conditions d'utilisation qu'aux operations de lavage et de decontamination. (auteurs)

  19. Generation de chemins de couverture pour des operations automatisees de controle non destructif appliquees dans l'industrie aerospatiale

    Science.gov (United States)

    Olivieri, Pierre

    Non destructive testing (NDT) plays an important role in the aerospace industry during the fabrication and maintenance of the structures built and is used, among other useful applications, to detect flaws such as cracks at an early stage. However, NDT techniques are still mainly done manually, especially on complex aeronautical structures, which then results in several drawbacks. In addition to be difficult and time-consuming, reliability and repeatability of inspection results are likely to be affected, since they rely on each operator's experience and dexterity. The present thesis is part of a larger project (MANU-418) of the Consortium for Research and Innovation in Aerospace in Quebec (CRIAQ). In this project, it has been proposed to develop a system using a 6-DOF manipulator arm to automate three particular NDT techniques often needed in the aerospace industry: eddy current testing (ECT), fluorescent penetrant inspection (FPI), and infrared thermography (IRT). The main objective of the MANU-418 project is to demonstrate the efficiency of the developed system and provide inspection results of surface and near surface flaws (cracks usually) at least as reliably and repeatably as inspection results from a human operator. One specific objective stemming from the main objective of the project is to develop a methodology and a software tool to generate covering paths adapted for the three aforementioned NDT techniques to inspect the complex surfaces of aerospace structures. The present thesis aims at reaching this specific objective. At first, geometrical and topological properties of the surfaces considered in this project are defined (flat surfaces, round and straight edges, cylindrical or near cylindrical surfaces, holes). It is also assumed that the 3D model of the surface to inspect is known in advance. Moreover, it has been decided within the framework of the MANU-418 project to give priority to the automation of ECT compared with the other techniques (FPI and

  20. L’Afrique et l’histoire des techniques. Hommage à François Sigaut Africa and the history of techniques. Tribute to François Sigaut

    Directory of Open Access Journals (Sweden)

    Monique Chastanet

    2013-02-01

    Full Text Available Spécialiste de l’histoire et de l’anthropologie des techniques des sociétés préindustrielles, dans le domaine de l’agriculture et de l’alimentation, François Sigaut (10 novembre 1940 – 2 novembre 2012 nous a quittés récemment, emporté en deux mois par un cancer, alors qu’il avait encore de nombreux travaux en chantier. Ses recherches étaient centrées sur l’Europe, mais il s’intéressait également aux autres continents, à l’Afrique en particulier. Cet intérêt était lié à sa démarche comparativ...

  1. Technique of calculating specific capital investments in the fuel extracting sectors of industry

    Energy Technology Data Exchange (ETDEWEB)

    Bugrov, V.A.; Filey, I.A.

    1980-01-01

    An analysis is made of the existing methods of calculating specific capital investments in the fuel extracting sectors of industry. Their shortcomings are shown. It is suggested that specific capital investments for extraction of coal and gas be defined as the ratio of capital investments to the conditional increase in extraction. Coal extraction should take int consideration all the capital investments associated with the input of new facilities, and the maintenance of the attained level of extraction and reconstruction of the enterprise, as well as all the newly introduced facilities both at the new and at the active enterprises associated with an increase in coal extraction and with maintenance of the facilities. The suggested technique completely corresponds to the ''Standard Technique for Developing a Technical-Industrial-Financial Plan,'' which stipulates determination of specific capital investments per unit of introduced facilities with only the difference that it takes into consideration the specific features of the fuel extracting sectors of industry.

  2. Fundamental aspects of oily waters treatment from the mineral industries by electrolytic techniques

    Energy Technology Data Exchange (ETDEWEB)

    Merma, A.G.; Gonzales, L.V.; Torem, M.L. [Pontifical Catholic Univ. of Rio de Janeiro, Rio de Janeiro (Brazil). Dept. of Materials Engineering

    2010-07-01

    There is an immediate need to develop innovative and more effective techniques for treatment of wastewaters as regulations on effluent wastewater discharge are becoming increasingly prevalent. The mining and metallurgical industries generate wastewaters that contain stable oil-in-water emulsions, arising from residues of liquid streams that serve the purpose of lubrication, cooling, cleaning and corrosion prevention in the equipment used in those industries. Chemically stabilized oil-water emulsions produced in the mineral industries can be treated using an electrocoagulation technique that considers the effects of operating parameters such as initial pH, current density, reaction time, electrode area/liquid volume ratio and electrode materials on the separation of oil as measured by the chemical oxygen demand. The paper discussed electrocoagulation as well as the materials and methods for the study, including oil in water emulsions; the experimental apparatus; and the experimental procedure. It was concluded that the electrolysis of this kind of oil in water emulsions with aluminum electrodes resulted in pH neutralization regardless of the initial pH tested. 18 refs., 4 figs.

  3. La structure sociale de l’industrie des Biotechnologies en France: une étude des relations inter-organisationnelles au niveau inter-individuel.

    Directory of Open Access Journals (Sweden)

    Piña-Stranger, Alvaro

    2010-06-01

    Full Text Available Various authors have shown the importance of collaborative relationships for inter-organizational performance, the mode of governance or the trajectory of biotechnology companies. Most of these works analyze the exclusive contractual agreements between companies and their main relationships among individuals. We show that this purely economic approach presents a major limitation: the nature of contractual relationships does not explore in detail how players cooperate. We propose to extend the study of these inter-organizational social relations, seen through the resource exchange in inter-individual. An empirical study on the leaders of the biotechnology industry in the area of human health in France has allowed us to map their relationships and resources they exchange them. Our results confirm the existence of a system of exchange dense and multiple. It presents a hierarchical distribution of various types of resources, where the centre is different from the periphery relations denser, more numerous and more reciprocal. However, comparative analysis of different networks reveals that the relationships of the board are highly centralized, while those of friendship following a more even distribution. We suggest that this phenomenon is part of a compensation mechanism to less central actors to maintain inter-organizational relationships. Finally, two standards of the cooperation process, revealed by the relational behaviour of actors, have been discovered. We suggest that they reflect in part the difficult process of adjustment that must cross a science project out of the realm of academic research and develop in a private structure: the biotech company.

  4. Application of Project Time Management Tools and Techniques to the Construction Industry in the Gaza Strip

    Directory of Open Access Journals (Sweden)

    Nabil Sawalhi

    2012-11-01

    Full Text Available The objective of this paper is to investigate the level of applying theproject time management tools and techniques by public ownersand construction contractors in the Gaza Strip. This study hasbeen conducted by means of a survey questionnaire. Seventythreequestionnaires were distributed to target constructioncontractors and twenty-five questionnaires to public owners. Sixtycompleted questionnaires from contractors and twenty-threequestionnaires from public owners were received and analysed.The survey results indicated that contemporary project timemanagement tools and techniques are not widely used amonglocal contractors and owners. Lack of subcontractor’s knowledgeand awareness of the importance of project time managementtools and techniques are still major obstacles toward the efficientutilisation of such tools. This study recommended that there is anurgent need to establish a professional industry body such as anInstitute of Building to review and evaluate existing local projectmanagement practices. This professional body may be establishedby the government through the Ministry of Housing and PublicWorks or by the local university in cooperation with a similarinternational professional industry body. Current training effortshould be tailored to encourage owners and contractors to usework breakdown structures, resource optimisation, and networkscheduling.

  5. Integration of quality improvement and cost-efficiency through industrial improvement techniques

    Directory of Open Access Journals (Sweden)

    Vink JP

    2016-06-01

    Full Text Available Jasper P Vink,1 Maxime T Rigaudy,1,2 Karl O Elmqvist11Imperial College Business School, Imperial College London, London, 2Hull York Medical School, York, UKIn this journal, Crema and Verbano1 discussed the importance of defining quality of health care and how quality can be improved through various industrial instruments and techniques. Quality of health care is a heavily debated topic that requires a wide scope of considerations across the many stakeholders of the health system. We acknowledge Crema and Verbano’s arguments that patient safety is a basic pillar of quality, upon which we would like to expand by highlighting the clinical effectiveness and patient-reported outcomes, which are the two further crucial components of quality. The arguments made regarding quality improvement techniques and cost efficiency in health care provision are insightful, yet appear to make a distinction between efforts to improve quality, eliminate waste from processes, and cut costs in health care provision. We would argue that in fact these achievements are all closely related and can be achieved simultaneously, if the industrial techniques of quality management are applied adequately.View the original paper by Crema and Verbano.

  6. Advanced CFD and radiotracer techniques - A complementary technology - for industrial multiphase applications

    International Nuclear Information System (INIS)

    Tu, J.Y.

    2004-01-01

    A CFD and RTD Education Package was developed, in which lecture notes, tutorials and computer softwares for both CFD and RTD are included. A user-friendly web-based interface has been prepared to allow lecturers more effectively conducting their training courses or workshops, and to provide students or users more easily learning the CFD and RTD knowledge and practising computer softwares. This report gives an overview of the advances in development and use of CFD models and codes for industrial, particularly multiphase processing applications. Experimental needs for validation and improvement of CFD models and softwares are highlighted. Integration of advanced CFD modelling with radiotracer techniques as a complementary technology for future research and industrial applications is discussed. The features and examples of the developed CFD and RTD Education package are presented. (author)

  7. Application of the pulsed neutron technique on the reactors ALIZE - AQUILON (1963); Application de la methode des neutrons pulses sur les piles ALIZE et AQUILON (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Jacquemart, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    Different methods of measuring the ratio effective delayed fraction / prompt neutron lifetime, {alpha}{sub c}, are described. According to the classic pulsed neutron technique the negative reactivity due to a localized absorber is given by {rho} / {beta}{sub eff} = {alpha} / {alpha}{sub c} -1 Experiments are reported which show that in this case {alpha}{sub c} can not be considered constant for large reactivities. The absorber element distorts the flux in the system, increasing the importance of the reflector. An application of the pulsed neutron method to the measurement of critical distributed boron concentrations of various absorber elements is described. Less time is required than for the usual super-critical techniques, and the experimental analysis is simplified. It is interesting to note that the results are not influenced by the spectral sensitivity of the control element. A modified pulsed neutron method has been tried out. This procedure was used to determine by measurements at sub-critical the critical water level of uranium-heavy water lattices with a high precision. (author) [French] Differents modes operatoires pour definir la valeur du rapport pourcentage effectif de neutrons retardes / temps de vie, {alpha}{sub c}, sont exposes. La methode classique par neutrons pulses definit l'anti-reactivite d'un element absorbant a partir de la relation: {rho} / {beta}{sub eff} {alpha} / {alpha}{sub c} -1 Les manipulations effectuees montrent qu'on ne peut considerer dans ce cas {alpha}{sub c} constant pour de tres grandes anti-reactivites. L'absorbant introduit dans la pile deforme le flux et augmente l'importance du reflecteur. Une application de la methode des neutrons pulses pour mesurer le titre critique en mg de B/l de divers absorbants est signalee. Les operations sont effectuees en regime sous-critique avec un certain gain de temps et une grande facilite de depouillement. Il est interessant de noter que les resultats ne sont pas

  8. Application of the pulsed neutron technique on the reactors ALIZE - AQUILON (1963); Application de la methode des neutrons pulses sur les piles ALIZE et AQUILON (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Jacquemart, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    Different methods of measuring the ratio effective delayed fraction / prompt neutron lifetime, {alpha}{sub c}, are described. According to the classic pulsed neutron technique the negative reactivity due to a localized absorber is given by {rho} / {beta}{sub eff} = {alpha} / {alpha}{sub c} -1 Experiments are reported which show that in this case {alpha}{sub c} can not be considered constant for large reactivities. The absorber element distorts the flux in the system, increasing the importance of the reflector. An application of the pulsed neutron method to the measurement of critical distributed boron concentrations of various absorber elements is described. Less time is required than for the usual super-critical techniques, and the experimental analysis is simplified. It is interesting to note that the results are not influenced by the spectral sensitivity of the control element. A modified pulsed neutron method has been tried out. This procedure was used to determine by measurements at sub-critical the critical water level of uranium-heavy water lattices with a high precision. (author) [French] Differents modes operatoires pour definir la valeur du rapport pourcentage effectif de neutrons retardes / temps de vie, {alpha}{sub c}, sont exposes. La methode classique par neutrons pulses definit l'anti-reactivite d'un element absorbant a partir de la relation: {rho} / {beta}{sub eff} {alpha} / {alpha}{sub c} -1 Les manipulations effectuees montrent qu'on ne peut considerer dans ce cas {alpha}{sub c} constant pour de tres grandes anti-reactivites. L'absorbant introduit dans la pile deforme le flux et augmente l'importance du reflecteur. Une application de la methode des neutrons pulses pour mesurer le titre critique en mg de B/l de divers absorbants est signalee. Les operations sont effectuees en regime sous-critique avec un certain gain de temps et une grande facilite de depouillement. Il est interessant de noter que les resultats ne sont pas affectes par la

  9. Studies of industrial emissions by accelerator-based techniques: A review of applications at CEDAD

    Science.gov (United States)

    Calcagnile, L.; Quarta, G.

    2012-04-01

    Different research activities are in progress at the Centre for Dating and Diagnostics (CEDAD), University of Salento, in the field of environmental monitoring by exploiting the potentialities given by the different experimental beam lines implemented on the 3 MV Tande-tron accelerator and dedicated to AMS (Accelerator Mass Spectrome-try) radiocarbon dating and IB A (Ion Beam Analysis). An overview of these activities is presented by showing how accelerator-based analytical techniques can be a powerful tool for monitoring the anthropogenic carbon dioxide emissions from industrial sources and for the assessment of the biogenic content in SRF (Solid Recovered Fuel) burned in WTE (Waste to Energy) plants.

  10. Studies of industrial emissions by accelerator-based techniques: A review of applications at CEDAD

    Directory of Open Access Journals (Sweden)

    Calcagnile L.

    2012-04-01

    Full Text Available Different research activities are in progress at the Centre for Dating and Diagnostics (CEDAD, University of Salento, in the field of environmental monitoring by exploiting the potentialities given by the different experimental beam lines implemented on the 3 MV Tande-tron accelerator and dedicated to AMS (Accelerator Mass Spectrome-try radiocarbon dating and IB A (Ion Beam Analysis. An overview of these activities is presented by showing how accelerator-based analytical techniques can be a powerful tool for monitoring the anthropogenic carbon dioxide emissions from industrial sources and for the assessment of the biogenic content in SRF (Solid Recovered Fuel burned in WTE (Waste to Energy plants.

  11. Determination of elements in industrial waste sample and TENORM using XRF Technique in Nuclear Malaysia

    International Nuclear Information System (INIS)

    Paulus, W.; Sarimah Mahat; Meor Yusoff Meor Sulaiman

    2011-01-01

    Industrial waste such as aluminium dross and TENORM waste, oil sludge has been used as sample in this research. Determination of main elements by using X-Ray Fluorescence (XRF) in Material Technology Group, Malaysian Nuclear Agency. Results shows that main elements in these samples, aluminium and silicon, respectively. Thereby, this research shows that XRF can be considered as one of the techniques that can be used in waste characterization and furthermore, it can help researchers and engineer in the research related to waste treatment especially radioactive waste. (author)

  12. Business Analysis Skills and Techniques Among Software Developers from Various BPO Industries In Iloilo City, Philippines

    Directory of Open Access Journals (Sweden)

    Alex Ledonio

    2016-11-01

    Full Text Available In Iloilo City, Philippines, BPO Industry is booming and an upcoming Megaworld Business District situates a multitude of BPO companies. In this study the software developers of various BPO companies in Iloilo City were evaluated according to their competency on Business Analysis Skill and Techniques. A common misconception is that IT programmers should be detached to business analysis process and will just have to wait for the requirement solution to implement through software development. This study will gauge how much skills and knowledge they possess on the Business Analysis side. The result of the study reveals that software developers evaluated has an average rating on Business Analysis Tasks and Techniques. Respondents are lacking skills generally on business planning, business requirements analysis, and elicitation processes. These results can be used as a baseline data to recommend a necessary adjustment in school curricula.

  13. Application of learning techniques based on kernel methods for the fault diagnosis in industrial processes

    Directory of Open Access Journals (Sweden)

    Jose M. Bernal-de-Lázaro

    2016-05-01

    Full Text Available This article summarizes the main contributions of the PhD thesis titled: "Application of learning techniques based on kernel methods for the fault diagnosis in Industrial processes". This thesis focuses on the analysis and design of fault diagnosis systems (DDF based on historical data. Specifically this thesis provides: (1 new criteria for adjustment of the kernel methods used to select features with a high discriminative capacity for the fault diagnosis tasks, (2 a proposed approach process monitoring using statistical techniques multivariate that incorporates a reinforced information concerning to the dynamics of the Hotelling's T2 and SPE statistics, whose combination with kernel methods improves the detection of small-magnitude faults; (3 an robustness index to compare the diagnosis classifiers performance taking into account their insensitivity to possible noise and disturbance on historical data.

  14. Application of RNB for high sensitive wear diagnostics in medicine technique and industry

    International Nuclear Information System (INIS)

    Fehsenfeld, P.; Eifrig, C.; Kubat, R.

    2002-01-01

    The RTM--Radionuclide Technique in Mechanical engineering--is now extended to the solution of world wide problems in medicine technique (prosthetics), and in development of modern materials (synthetic materials, ceramics, hard coatings, etc.) and their industrial application. RNB--Radioactive Nuclear Beams of 7 Be or 22 Na--may enable the required extreme thin radioactive surface labeling (several micrometers) of synthetic materials for wear measurements without producing radiation damages of influence to the wear properties of the material. The function principle and special properties of the RTM on-line wear diagnostics and its components, the measurement methods, the radioactive surface labeling, and the measurement instruments are explained. The quality features of a 7 Be and 22 Na-beam for RTM application are specified

  15. Directory of the manufacturers and suppliers for the French wind power industry; Annuaire des fabricants et fournisseurs de l'industrie eolienne 2010-2011

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-11-15

    With over 5, 660 MW installed in end-2010, France ranks fourth in Europe, behind Germany, Spain and Italy. The wind power industry currently employs almost 11, 000 people in France throughout the value chain. In 2009, the first edition of this directory listed over one hundred companies working in around twenty different areas. Encouraged by these initial positive results, and with the help of ADEME, the French syndicate for renewable energies (SER) asked Capgemini Consulting to undertake a study to identify and raise awareness among French industrials likely to enter into the wind energy market. The French Ministry for Ecology, Energy, Sustainable Development and the Sea, along with the Ministry for the Economy, Finance and Employment, were involved in the work. 400 companies were questioned as part of the study. Over 150 replies testified to the dynamic character of the wind power market in France and overseas, and the opportunities for diversification that it represents for traditional industries like metallurgy, aeronautics, defence and shipyards, etc. The study led to the creation of the initiative Windustry France, which currently groups over 300 companies either active in the French wind power market or set to enter it. Windustry France is a showcase of the industrial know-how that can be used in the wind power industry both onshore and offshore. It includes local set-ups developed around major fields of activity (e.g. car industry, aeronautics, mechanics, etc.) and industrial port zones (Dunkerque, Rouen/Le Havre, Brest, Nantes Saint-Nazaire, Bordeaux, etc.). Several ministries, regional stakeholders and authorities are also involved (local authorities, Regional directorates for industry, research and the environment (DReal) networks and chambers of commerce and industry), all of which contribute to making Windustry France a collective approach to industrial policy. The 2010-2011 edition of the directory of manufacturers and suppliers for the wind power

  16. Fuzzy logic and modeling of ventilation networks in the nuclear industry; Logique floue et modelisation des reseaux de ventilation dans l'industrie nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Floquet, P.; Lhoste, J.C.; Domenech, S.; Pibouleau, L. [Ecole Nationale Superieure des Arts Chimiques et Technologiques, Lab. de Genie Chimique, LGC, UMR CNRS/INP/UPS 5503, 31 - Toulouse (France); Laborde, J.C. [CEA Saclay, Institut de la Protection et de la Surete Nucleaire, IPSN, DPEA/SERAC, 91 - Gif-sur-Yvette (France)

    2001-07-01

    This article presents the implementation of fuzzy logic in the modeling of ducts, filters and pressures of the ventilation networks of the nuclear industry, taking into account the uncertainties of the aeraulic parameters. (J.S.)

  17. Treatment techniques for the recycling of bottle washing water in the soft drinks industry.

    Science.gov (United States)

    Ramirez Camperos, E; Mijaylova Nacheva, P; Diaz Tapia, E

    2004-01-01

    The soft drink production is an important sector in the manufacturing industry of Mexico. Water is the main source in the production of soft drinks. Wastewater from bottle washing is almost 50% of the total wastewater generated by this industry. In order to reduce the consumption of water, the water of the last bottle rinse can be reused in to the bottle pre-rinse and pre-washing cycles. This work presents the characterization of the final bottle washing rinse discharge and the treatability study for the most appropriate treatment system for recycling. Average characteristics of the final bottle wash rinse were as follows: Turbidity 40.46 NTU, COD 47.7 mg/L, TSS 56 mg/L, TS 693.6 mg/L, electrical conductivity 1,194 microS/cm. The results of the treatability tests showed that the final rinse water can be used in the pre-rinse and pre-washing after removing the totality of the suspended solids, 80% of the COD and 75% of the dissolved solids. This can be done using the following treatment systems: filtration-adsorption-reverse osmosis, or filtration-adsorption-ion exchange. The installation of these treatment techniques in the soft drink industry would decrease bottle washing water consumption by 50%.

  18. Application of predictive modelling techniques in industry: from food design up to risk assessment.

    Science.gov (United States)

    Membré, Jeanne-Marie; Lambert, Ronald J W

    2008-11-30

    In this communication, examples of applications of predictive microbiology in industrial contexts (i.e. Nestlé and Unilever) are presented which cover a range of applications in food safety from formulation and process design to consumer safety risk assessment. A tailor-made, private expert system, developed to support safe product/process design assessment is introduced as an example of how predictive models can be deployed for use by non-experts. Its use in conjunction with other tools and software available in the public domain is discussed. Specific applications of predictive microbiology techniques are presented relating to investigations of either growth or limits to growth with respect to product formulation or process conditions. An example of a probabilistic exposure assessment model for chilled food application is provided and its potential added value as a food safety management tool in an industrial context is weighed against its disadvantages. The role of predictive microbiology in the suite of tools available to food industry and some of its advantages and constraints are discussed.

  19. Advanced dust control techniques in cement industry electrostatic precipitator - a case study

    International Nuclear Information System (INIS)

    Khattak, Z.; Ahmad, J.

    2011-01-01

    The case study deal with the current day problem of pollution by industrial zones in Pakistan with emphasis on the cement Industry which has been proved to be the second revenue generating hub after textile sector of the Pakistan. A pilot study into the identification and available removal Techniques of particulates from the exhaust of a cement plant clinker cooler was carried out. The objective of this work was to study the performance of the each technique in detail in the removal of a particulate with a wide range of sizes, under different operational conditions and to compare the results for collection efficiency with predictions by available theoretical models. A brief and comprehensive discussion regarding design, construction and bottlenecks of each tool has been discussed to fully ascertain it's scope and usability. First part of the study identifies the various pollutants being emitted from the chimney of a specific cement plant in Pakistan and while last portion deals with the ways to curtail these pollutants. (author)

  20. Advanced techniques for energy-efficient industrial-scale continuous chromatography

    Energy Technology Data Exchange (ETDEWEB)

    DeCarli, J.P. II (Dow Chemical Co., Midland, MI (USA)); Carta, G. (Virginia Univ., Charlottesville, VA (USA). Dept. of Chemical Engineering); Byers, C.H. (Oak Ridge National Lab., TN (USA))

    1989-11-01

    Continuous annular chromatography (CAC) is a developing technology that allows truly continuous chromatographic separations. Previous work has demonstrated the utility of this technology for the separation of various materials by isocratic elution on a bench scale. Novel applications and improved operation of the process were studied in this work, demonstrating that CAC is a versatile apparatus which is capable of separations at high throughput. Three specific separation systems were investigated. Pilot-scale separations at high loadings were performed using an industrial sugar mixture as an example of scale-up for isocratic separations. Bench-scale experiments of a low concentration metal ion mixture were performed to demonstrate stepwise elution, a chromatographic technique which decreases dilution and increases sorbent capacity. Finally, the separation of mixtures of amino acids by ion exchange was investigated to demonstrate the use of displacement development on the CAC. This technique, which perhaps has the most potential, when applied to the CAC allowed simultaneous separation and concentration of multicomponent mixtures on a continuous basis. Mathematical models were developed to describe the CAC performance and optimize the operating conditions. For all the systems investigated, the continuous separation performance of the CAC was found to be very nearly the same as the batchwise performance of conventional chromatography. the technology appears, thus, to be very promising for industrial applications. 43 figs., 9 tabs.

  1. Scanning Techniques for Brain-Tumour, Localization; Techniques Scintigraphies pour la Iocalisation des Tumeurs Cerebrales; Tekhnika skennirovaniya pri opredelenii lokalizatsii opukholej mozga; Tecnicas Centelleograficas para la Localizacion de Tumores Cerebrales

    Energy Technology Data Exchange (ETDEWEB)

    Duggan, M. H.; Brice, J.; Jones, E.; Mallard, J. R.; Myers, M. L. [Department Of Medical Physics, Postgraduate Medical School, Hammersmith Hospital, London (United Kingdom)

    1964-10-15

    may then be compared with this pattern. Such analysis lends itself to computer techniques. The use of continuous averaging techniques may also prove to be of value in improving the perception of abnormalities near the limits of detection in moving detector systems. The possible use of multichannel analysers to apply this and at the same time make possible a valuable new display system for both moving and stationary systems is presented. (author) [French] On a utilise l'appareil de gammagraphie en couleurs pour la scintigraphie de deux series cliniques de tumeurs cerebrales, dans le premier cas au moyen de {sup 74}As (detection des positons), dans le deuxieme cas au moyen de l'albumine marquee avec {sup 131}I (detection des rayons gamma, avec un collimateur a focalisation). L'auteur compare les resultats obtenus dans les deux series. Matthews a montre, dans des etudes sur des rats ayant des tumeurs, que le citrate de {sup 206}Bi devrait etre un materiau particulierement favorable pour la localisation des tumeurs cerebrales; aussi fait-on actuellement une troisieme serie clinique avec ce produit (detection des rayons gamma, avec un collimateur a focalisation). L'auteur presente les resultats preliminaires de cette etude. Les collimateurs a focalisation utilises pour les emetteurs gamma ont un foyer geometrique profond et donnent, pour des sources ponctuelles, des courbes d'isoreponse qui sont presque independantes de la profondeur sur une distance de 20 cm. Les resultats des experiences faites avec une serie de collimateurs ont fourni les donnees necessaires a la realisation de collimateurs de ce genre destines a des fins determinees. Des tumeurs du cerveau ont ete explorees avec un detecteur stationnaire, en ayant recours a la photographie gamma et a l'enregistrement par un oscilloscope a memoire. Les avantages de ce procede resident dans une plus grande sensibilite et une visualisation plus rapide de la repartition de la radioactivite, ce qui permet de proceder a des

  2. Gestion des risques

    CERN Document Server

    Louisot, Jean-Paul

    2009-01-01

    Depuis le début du lie siècle, la gestion des risques connaît une véritable révolution culturelle. Jusqu'alors fonction technique, centrée autour de l'achat de couverture d'assurances, elle est devenue une discipline managériale et transversale : une valise d'instruments que chaque manager doit connaître et appliquer quels que soient son domaine de compétence et ses missions au sein de l'organisation. En effet, la gestion des risques est une culture qui doit être assimilée par chacun des acteurs. C'est précisément l'ambition des 101 questions rassemblées dans cet ouvrage : apporter à chaque manager d'entreprise, de collectivité, d'établissement de santé..., des réponses claires au " pourquoi " et au " comment " : Comment identifier les risques ? Comment analyser les risques ? Quels sont les objectifs de la gestion des risques ? Une carte des risques pour quoi faire ? Pourquoi faut-il financer les risques ? Les entreprises ont-elles des responsabilités pénales ? En quoi consiste la gestion...

  3. Nuclear measurements, techniques and instrumentation, industrial applications, plasma physics and nuclear fusion 1986-1996. International Atomic Energy Agency publications

    International Nuclear Information System (INIS)

    1997-03-01

    This catalogue lists all sales publications of the International Atomic Energy Agency dealing with Nuclear Measurements, Techniques, and Instrumentation, Industrial Applications, Plasma Physics and Nuclear Fusion, issued during the period 1986-1996. Most publications are in English. Proceedings of conferences, symposia and panels of experts may contain some papers in languages other than English (French, Russian or Spanish), but all of these papers have abstracts in English. Contents cover the three main areas of (i) Nuclear Measurements, Techniques and Instrumentation (Physics, Dosimetry Techniques, Nuclear Analytical Techniques, Research Reactor and Particle Accelerator Applications, and Nuclear Data), (ii) Industrial Applications (Radiation Processing, Radiometry, and Tracers), and (iii) Plasma Physics and Controlled Thermonuclear Fusion

  4. The Use of Information Technology Techniques in the Construction Industry of Pakistan

    Directory of Open Access Journals (Sweden)

    Zubair Ahmed Memon

    2012-04-01

    Full Text Available Construction sector together with service, manufacturing, agriculture and mining sectors is the main contributors of the Pakistan\\'s GDP (Gross Domestic Product and economic growth. It is also a key indicator in determining the economic performance of the country. As the issues of globalization and trades deregulation, stringer requirements of time, cost, quality and advancement of technologies have become more critical, the sector has to find ways to enhance its operational efficiency and effectiveness. IT (Information Technology as a key enabler has been recognized to be an inseparable tool to sustain business and become more competitive. This paper gives an overview of the current status of IT application and presents the significant results from PCI (Pakistan Construction Industry. The result of survey also highlights the challenges to the construction industry of Pakistan before implementing the IT techniques. A statistical method \\'Average Index\\' is used to analyze the collected data and statistical hypothesis testing is conducted to know the difference between the parameters. The survey produced knowledge about the use of computers, hardware and software, communication and strategies for the use of IT. The use of spread sheets, word processor, CAD (Computer Aided Drafting in general has increased and the use of model based CAD software has increased among the major key players of construction industry. The use of project webs and electronic trade in the industry is not started properly. From the analysis it is concluded that construction firms in Pakistan are mostly using manual procedures and the use of IT seems to be at the inception stage

  5. Contribution to the study of protein deficiency: Use of radioisotope techniques; Contribution a l'etude des etats de malnutrition proteique utilisation de méthodes isotopiques

    Energy Technology Data Exchange (ETDEWEB)

    Dubois, J.; Colard, J.; Vis, H. L. [Université libre de Bruxelles, Brussels (Belgium); Centre d' étude de l' énergie nucléaire, Mol (Belgium)

    1970-01-15

    Research methods based on the use of radioisotopes have already been used for some time to study the physiopathogenesis of malnutritional and denutritional conditions in childhood. Two very specific aspects of malnutrition are studied primarily by means of these techniques: plasma protein metabolism proper and hydroelectrolytic disorders, which are an integral part of the physiopathogenetic picture of the disease. The authors have attempted, in so far as is possible, to define the clinical condition of children from along Lake Kivu, in the east of Kivu Province, who are suffering from protein and calorie deficiency. (author) [French] Les méthodes d'investigation à l'aide de radioisotopes ont été, depuis un certain temps déjà, utilisées pour l'étude de la physiopathogénie des états de malnutrition et de dénutrition de l'enfance. Deux aspects bien particuliers de la malnutrition sont surtout étudiés à l'aide de ces méthodes: le métabolisme propre des protéines plasmatiques et les troubles hydro-électrolytiques qui font partie intégrante du tableau physiopathogénique de l'affection. Les auteurs ont essayé de définir, le mieux possible, l'état clinique des enfants de l'est de la province du Kivu, le long du lac Kivu, souffrant de malnutrition protéo-calorique. (author)

  6. MRI of the wrist: Comparison of high resolution pulse sequences and different fat-suppression techniques; Magnetresonanztomographie des Handgelenks - Vergleich hochaufloesender Pulssequenzen und unterschiedlicher Fettsignalunterdrueckungen an Leichenpraeparaten

    Energy Technology Data Exchange (ETDEWEB)

    Staebler, A.; Spieker, A.; Bonel, H.; Glaser, C.; Reiser, M. [Klinikum Grosshadern, Muenchen (Germany). Inst. fuer Radiologische Diagnostik; Schrank, C.; Putz, R. [Muenchen Univ. (Germany). Anatomische Anstalt; Petsch, R. [Siemens AG, Erlangen (Germany). Unternehmensbereich Medizinische Technik

    2000-02-01

    Purpose: To evaluate high resolution sequences with and without fat-suppression techniques for MR imaging of the wrist. Results: The highest homogeneity and the least artifacts were achieved by the T{sub 1}-w SE sequence. For the STIR and PD-FS TSE sequence high rankings were found for the detection of free water. The PD FS sequence had high ranking also for visualization of the SL ligament and the triangular fibrocartilage. The best sequence for the assessment of hyaline cartilage was the FLASH-FS sequence. For detailed analysis of bony structures the CISS sequence performed best. Conclusion: The isolated use of a PD-FS-TSE sequence enables for evaluation of all clinically relevant structures at the wrist. Dedicated questions for hyaline cartilage are answered best by the use of a FLASH 3D-FS sequence. Selective water excitation reduces acquisition time to 60%, nevertheless FS sequences are still diagnostically superior to WE sequences. (orig./AJ) [German] Ziel: Beurteilung der Wertigkeit hochaufloesender MRT-Sequenzen ohne und mit Fettsignalunterdrueckung (FS) und selektiver Wasseranregung (WE) fuer Untersuchungen des Handgelenkes. Ergebnisse: SE-T{sub 1} zeigte die hoechste Signalhomogenitaet bei geringsten Artefakten. Die STIR und PD FS-Sequenz stellten Signal von freiem Wasser am besten dar. Die beste Knorpeldarstellung erreicht die FLASH 3D-FS-Sequenz. Die Kortikalis und die Spongiosa konnten am besten mit der CISS-Sequenz beurteilt werden. Die FS-Sequenzen waren den WE-Sequenzen diagnostisch ueberlegen. Schlussfolgerungen: Mit der PD FS TSE-Sequenz mit verlaengerter Echozeit ist eine gute Beurteilung aller klinisch wichtigen Strukturen moeglich. Die beste Darstellung des hyalinen Knorpels wird mit der FLASH-3D-FS-, des Knochens mit der CISS-Sequenz erreicht. Die selektive Wasseranregung bei FLASH- und DESS-Sequenzen reduziert die Aufnahmezeit, ohne die diagnostische Aussagekraft der FS-Sequenzen zu erreichen. (orig./AJ)

  7. The atomic energy course of the 'Institut National des Sciences et Techniques nucleaires' at the centre d'Etudes Nucleaires at Saclay; L'enseignement de genie atomique de l'Institut national des Sciences et Techniques nucleaires au Centre d'Etudes nucleaires de Saclay

    Energy Technology Data Exchange (ETDEWEB)

    Baissas, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    foreign students. 8- Annexe: list of courses, practical work, pile projects drawn up by the 1957 students. (author)Fren. [French] 1- Les raisons de sa creation. L'electricite de France et l'industrie interessee par le developpement de l'Energie atomique ont demande au Commissariat a l'Energie atomique de former des ingenieurs capables d'etudier des projets de piles et de diriger leur construction. 2- Recrutement et Droits d'inscription. Les demandes d'inscription ont toujours depasse les possibilites. Cette annee, les cours sont suivis par 74 eleves permanents, dont 20 etrangers, et une centaine d'auditeurs libres. Tous les elevont deja ingenieurs ou nantis de grades universitaires eleves. Droit d'inscription: 250 000 F pour les eleves, 125 000 F pour les auditeurs. 3- Organisation de l'Enseignement. II comprend deux options: physique et chimie et dans chaque option: une centaine de conferences, une trentaine de travaux pratiques, des stages dans les services, l'etude d'un projet de reacteur par un groupe de 4 ou 5 eleves. L'ensemble occupe l'annee universitaire du 1 novembre au 14 juillet. 4- Sanction. Un examen final combinant les notes de deux epreuves theoriques, des travaux pratiques, du stage, et du projet conduit a un diplome d'ingenieur en genie atomique. Il n'est pas cree en realite de nouveaux ingenieurs; une mention nouvelle est seulement ajoutee a un diplome deja acquis. Les resultats ont toujours ete excellents. Le pourcentage des echecs est tres faible. 5- Placement des Diplomes. Ils reviennent tous dans leurs industries d'origine qui ont paye leurs salaires et les droits d'inscription en se privant de leurs services pendant les neuf mois de duree des cours. 6- Creations analogues. Un cours analogue a ete cree au Centre d'Etudes Nucleaires de Grenoble. Tandis que celui de SACLAY s'adresse plus specialement aux ingenieurs deja en fonctions, celui de Grenoble est, en principe, destine aux jeunes ingenieurs sortant des ecoles. 7- Conclusion. L

  8. The internationalization of the technological activities in the energy industries; L'internationalisation des activites technologiques dans les industries energetiques

    Energy Technology Data Exchange (ETDEWEB)

    Bourgeois, B. [Institut d' Economie et de Politique de l' Energie - IEPE-CNRS/ Universite Pierre Mendes-France, 38 - Grenoble (France); Jacquier-Roux, V. [Institut de Recherche Economique sur la Production et le Developpement -IREPD, 38 - Grenoble (France)

    2001-06-01

    This analysis of the technological internationalization factors is defined in five chapters. The first chapter deals with the evolutionist representation of the internationalization process of the technological activities of the firms. The chapter two is an historical synthesis from 1985 to 2000, of the industrial dynamics and of the technological strategies of the petroleum and electric power industries. The chapter three details the empirical method used to verify the hypothesis. Chapter four exposes the data analysis results of the patents of the sampled firms. The last chapter is devoted to the results interpretation. (A.L.B.)

  9. Definition of the chief physical quantities in use in vacuum techniques, and their corresponding units; Definition des principales grandeurs physiques en usage dans la technique du vide et des unites correspondantes

    Energy Technology Data Exchange (ETDEWEB)

    Boulassier, J. C. [Commissariat a l' energie atomique et aux energies alternatives - Service de Physique Appliquee, CEA (France)

    1959-07-01

    It would seem desirable for vacuum technicians to adopt the coherent systems of units generally used in physics. This article presents an internal standardisation project in the CEA, and gives a brief review of the definitions of the physical quantities to which it applies. Reprint of a paper published in 'Le vide', n. 79, January-February 1959, p. 29-35 [French] Il serait souhaitable de voir les techniciens du vide adopter les systemes d'unites coherents usites generalement en physique. Cet article presente un projet de normalisation interne au C.E. A. et rappelle succinctement les definitions des grandeurs physiques auxquelles il se rapporte. Reproduction d'un article publie dans 'Le vide', n. 79, Janvier-Fevrier 1959, p. 29-35.

  10. A Method for Dynamically Selecting the Best Frequency Hopping Technique in Industrial Wireless Sensor Network Applications.

    Science.gov (United States)

    Fernández de Gorostiza, Erlantz; Berzosa, Jorge; Mabe, Jon; Cortiñas, Roberto

    2018-02-23

    Industrial wireless applications often share the communication channel with other wireless technologies and communication protocols. This coexistence produces interferences and transmission errors which require appropriate mechanisms to manage retransmissions. Nevertheless, these mechanisms increase the network latency and overhead due to the retransmissions. Thus, the loss of data packets and the measures to handle them produce an undesirable drop in the QoS and hinder the overall robustness and energy efficiency of the network. Interference avoidance mechanisms, such as frequency hopping techniques, reduce the need for retransmissions due to interferences but they are often tailored to specific scenarios and are not easily adapted to other use cases. On the other hand, the total absence of interference avoidance mechanisms introduces a security risk because the communication channel may be intentionally attacked and interfered with to hinder or totally block it. In this paper we propose a method for supporting the design of communication solutions under dynamic channel interference conditions and we implement dynamic management policies for frequency hopping technique and channel selection at runtime. The method considers several standard frequency hopping techniques and quality metrics, and the quality and status of the available frequency channels to propose the best combined solution to minimize the side effects of interferences. A simulation tool has been developed and used in this work to validate the method.

  11. Optical coherence tomography as an accurate inspection and quality evaluation technique in paper industry

    Science.gov (United States)

    Prykäri, Tuukka; Czajkowski, Jakub; Alarousu, Erkki; Myllylä, Risto

    2010-05-01

    Optical coherence tomography (OCT), a technique for the noninvasive imaging of turbid media, based on low-coherence interferometry, was originally developed for the imaging of biological tissues. Since the development of the technique, most of its applications have been related to the area of biomedicine. However, from early stages, the vertical resolution of the technique has already been improved to a submicron scale. This enables new possibilities and applications. This article presents the possible applications of OCT in paper industry, where submicron or at least a resolution close to one micron is required. This requirement comes from the layered structure of paper products, where layer thickness may vary from single microns to tens of micrometers. This is especially similar to the case with high-quality paper products, where several different coating layers are used to obtain a smooth surface structure and a high gloss. In this study, we demonstrate that optical coherence tomography can be used to measure and evaluate the quality of the coating layer of a premium glossy photopaper. In addition, we show that for some paper products, it is possible to measure across the entire thickness range of a paper sheet. Furthermore, we suggest that in addition to topography and tomography images of objects, it is possible to obtain information similar to gloss by tracking the magnitude of individual interference signals in optical coherence tomography.

  12. The Finnish background report for the EC documentation of best available techniques for tanning industry

    Energy Technology Data Exchange (ETDEWEB)

    Kustula, V.; Salo, H.; Witick, A.; Kaunismaa, P.

    2000-08-01

    The objective of this document is to identify best available techniques (BAT) for the reduction of emissions and energy use in the tanning industry in Finland. The leather tanning industry in Finland has long traditions, dating back for centuries, but today there are only nine tanneries of any importance left. The tanneries vary in size from small, family-owned ones to large on a Finnish scale, with a staff of about 70 persons. The production of finished leather in even the largest tannery in Finland is well below the production limit (12 tonnes finished leather a day) mentioned in the IPPC-directive (96/61/EC). The range of products manufactured by the Finnish leather industry is large and includes processed leather for, e.g. footwear, clothing, furniture and intermediate products, e.g. wet-blue and crust. The hides and skins of cows, lamb, elk, reindeer and occasionally skins from other animals, e.g. horses are the main raw materials used. Some of the tanneries carry out only a part of the processing and sell their products in a treated, but not finished state. Tanneries which undertake only a part of the preparation process are reviewed in this document as well. Because of the varying size of the Finnish tanneries, the quality and quantity of emissions and environmental impacts vary considerably. The parameters used by the authorities are suspended solids (SS), biological oxygen demand (BOD), and chromium and sulphide concentration in the effluents. The quantity of waste and waste water generated is also subject to assessment by the authorities. Direct regulation of emissions is practised in Finland by issuing permits containing emission limit values. Major waste streams generated are sludge from waste water treatment plants, animal residues from the beamhouse stage, residues from tanned leather and chemicals used. Various ways of residue separation and consequently reuse and recovery are practised in most Finnish tanneries. The proteinaceous residues from the

  13. Systems analysis on the humanization of industrial life in the coal mining industry. Pt. 2. Results. Systemanalyse zur Humanisierung des Arbeitslebens im Steinkohlenbergbau. T. 2. Ergebnisse

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    Volume No. 8 of the series of papers quantifies the system of aims, i.e. it defines synthetic data of laws and regulations of mining of DIN standards, and VDI guidelines, of generally accepted rules of engineering as well as of certified findings of industrial science as minimum requirements. This definition is followed by the examination of the type of medium-term development to be expected in the bituminous coal mining industry of the Ruhrkohle AG up to the year 1985. Then the general aims 1 and 2 given in volume No. 7 are described in detail. These descriptions constitute an excellent summary of the present state of knowledge concerning the improvement of working conditions in the bituminous coal mining industry. Finally, a study on the transferability of research findings is given. One statement is of special importance, i.e., that transferability is not characterized by technological feasibility alone which depends to a high degree on marginal, organizational conditions within the company, e.g., on the information system, on its hierarchical structure, on the company's policy, and on departamental policy. In this study, only the technological transferability is examined. To enable us to assess it, appropriate statements are made in a brief description of the research project carried out since 1974, which was sponsored within the action programme ''Humanization of Industrial Life''.

  14. Materials contamination control in the microelectronic industry; Controle de la contamination des materiaux dans l`industrie de la micro-electronique

    Energy Technology Data Exchange (ETDEWEB)

    Tardif, F

    1994-12-31

    This paper deals with many aspects of the contamination of materials in the microelectronic industry. The contamination`s control of chemicals, process gases, silicon and the survey of the ions free water`s purity are treated. (TEC). 29 figs., 7 tabs.

  15. Radioisotope techniques for problem solving in the offshore oil and gas industry

    International Nuclear Information System (INIS)

    Charlton, J.S.; Hurst, J.A.

    1994-01-01

    Radioisotope technology has been used for almost half a century by the oil and gas industry to solve problems and to help optimize process operations. The use of radioactive isotopes to investigate the effectiveness of well stimulation procedures and to measure the sweep-out patterns of oil and gas in secondary recovery process is well known. The applications of radioisotopes to study features of plant and process operation has been less widely reported though the economic benefits deriving from such applications are very great. Nevertheless, there has been continuous development in the range of application and in the design of equipment to facilitate the use of the technology at remote environments such as an oil or gas platform. Some indication of the current usage of radioisotope techniques may be obtained from examination of Table I, which lists projects carried out in the UK's North Sea fields by ICI Tracerco, which is the world's largest radioisotope applications service group

  16. Impurities in sugar cane and their influence on industrial processing evaluated by nuclear techniques

    International Nuclear Information System (INIS)

    Bacchi, M.A.; Fernandes, E.A.N.; Ferraz, E.S.B.

    1990-01-01

    During the cutting and loading operations, impurities, mainly soil, are added to sugar cane in amounts that can impair industrial processing due to excessive wear of metallic members and contamination of juice and bagasse. Mechanization of loading operation has showed a considerable enhancement of the impurity content, leading to the improvement of cane washing technology. Nevertheless, for a correct understanding of the problem and the process optimization, it is necessary and exact and fast quantification of these impurities as well as of its consequences. Nuclear techniques, in special neutron activation analysis, have been proved to be appropriate for estimating soil level in sugar cane, washing process efficiency and wearing of cases and moving parts. (author)

  17. Pyrite: A blender plugin for visualizing molecular dynamics simulations using industry-standard rendering techniques.

    Science.gov (United States)

    Rajendiran, Nivedita; Durrant, Jacob D

    2018-05-05

    Molecular dynamics (MD) simulations provide critical insights into many biological mechanisms. Programs such as VMD, Chimera, and PyMOL can produce impressive simulation visualizations, but they lack many advanced rendering algorithms common in the film and video-game industries. In contrast, the modeling program Blender includes such algorithms but cannot import MD-simulation data. MD trajectories often require many gigabytes of memory/disk space, complicating Blender import. We present Pyrite, a Blender plugin that overcomes these limitations. Pyrite allows researchers to visualize MD simulations within Blender, with full access to Blender's cutting-edge rendering techniques. We expect Pyrite-generated images to appeal to students and non-specialists alike. A copy of the plugin is available at http://durrantlab.com/pyrite/, released under the terms of the GNU General Public License Version 3. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  18. The radioactive wastes management of the little nuclear industry; La gestion des dechets radioactifs du nucleaire diffus

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Among the ANDRA customers, more than one million are little producers: hospital, research centers and industries. They are called little producers because of the low volume of produced wastes. Meanwhile these wastes management need an appropriate technology which is presented in this document. (A.L.B.)

  19. Information letter on industrial and commercial applications of electrical equipment; La lettre des applications industrielles et tertiaires du materiel electrique

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    This issue of Electricite de France research department newsletter, is composed of three articles, which titles and themes are: series reactance, a solution for the optimization of alternating current arc furnace performances; from industrial field buses to smart building field buses, owing to EDF testing; new methods for the voltage drop desensitization of frequency converters for asynchronous machines

  20. Review of the analytical techniques used in the hydrogeochemical prospecting of uranium; Revue des techniques analytiques utilisees dans la prospection hydrogeochimique de l'uranium

    Energy Technology Data Exchange (ETDEWEB)

    Grimbert, A; Berthollet, P [Commissariat a l' Energie Atomique, Section de Geochimie de la Dir. des Recherches et Exploitations Minieres, Fontenay aux Roses (France)

    1959-07-01

    This report examines the methods recommended for the estimation of uranium in water. The advantages and disadvantages of these methods are studied with respect to the qualities necessary for the hydrogeochemical prospecting of uranium sensitivity of the order of 1/5 ppb with an accuracy of 15 to 20 per cent, high fidelity, rapidity, simplicity and low cost. (author) [French] Ce rapport examine les methodes preconisees pour le dosage de l'uranium dans les eaux; les avantages et les inconvenients de ces methodes sont etudies en fonction des qualites necessitees par la prospection hydrogeochimique de l'uranium: sensibilite de l'ordre de 1/5 de ppb avec une precision de 15 a 20 pour cent, grande fidelite, rapidite, simplicite, et bas prix de revient. (auteur)

  1. Radioisotope techniques for process optimisation and control in the offshore oil and gas industries

    International Nuclear Information System (INIS)

    Charlton, J.S.

    2002-01-01

    For over fifty years, radioisotope technology has been used by the oil industry to solve problems and to help optimise process operations. The widespread development of offshore oil and gas fields has brought, and continues to bring, new challenges and, in response, new or modified applications of radioisotope technology have been introduced. This paper presents case studies, which illustrate the use of radioisotopes, both in the sub-sea environment and on the offshore production platforms. On the platform, radioisotope techniques applied singly or in combination, have been applied to the performance assessment of oil/gas separation and gas dehydration units. Novel nucleonic instrumentation has been developed for the control of three-phase separators. Sub-sea, radioactive tracers and/or sealed sources have been used to investigate the integrity of submerged structures and to troubleshoot pipeline problems. The continuing expansion in the use of this technology stems from industry increasing awareness of its versatility and from the fact that the benefits it confers can be obtained at a relatively modest cost. Examples of economic benefit described in the paper are associated with production enhancements derived from the ability of radioisotope technology to measure performance and diagnose problems on line, without disrupting process operations in any way. (Author)

  2. A Comparison of Alternative Distributed Dynamic Cluster Formation Techniques for Industrial Wireless Sensor Networks.

    Science.gov (United States)

    Gholami, Mohammad; Brennan, Robert W

    2016-01-06

    In this paper, we investigate alternative distributed clustering techniques for wireless sensor node tracking in an industrial environment. The research builds on extant work on wireless sensor node clustering by reporting on: (1) the development of a novel distributed management approach for tracking mobile nodes in an industrial wireless sensor network; and (2) an objective comparison of alternative cluster management approaches for wireless sensor networks. To perform this comparison, we focus on two main clustering approaches proposed in the literature: pre-defined clusters and ad hoc clusters. These approaches are compared in the context of their reconfigurability: more specifically, we investigate the trade-off between the cost and the effectiveness of competing strategies aimed at adapting to changes in the sensing environment. To support this work, we introduce three new metrics: a cost/efficiency measure, a performance measure, and a resource consumption measure. The results of our experiments show that ad hoc clusters adapt more readily to changes in the sensing environment, but this higher level of adaptability is at the cost of overall efficiency.

  3. ASSESSMENT OF DYNAMIC PRA TECHNIQUES WITH INDUSTRY AVERAGE COMPONENT PERFORMANCE DATA

    Energy Technology Data Exchange (ETDEWEB)

    Yadav, Vaibhav; Agarwal, Vivek; Gribok, Andrei V.; Smith, Curtis L.

    2017-06-01

    In the nuclear industry, risk monitors are intended to provide a point-in-time estimate of the system risk given the current plant configuration. Current risk monitors are limited in that they do not properly take into account the deteriorating states of plant equipment, which are unit-specific. Current approaches to computing risk monitors use probabilistic risk assessment (PRA) techniques, but the assessment is typically a snapshot in time. Living PRA models attempt to address limitations of traditional PRA models in a limited sense by including temporary changes in plant and system configurations. However, information on plant component health are not considered. This often leaves risk monitors using living PRA models incapable of conducting evaluations with dynamic degradation scenarios evolving over time. There is a need to develop enabling approaches to solidify risk monitors to provide time and condition-dependent risk by integrating traditional PRA models with condition monitoring and prognostic techniques. This paper presents estimation of system risk evolution over time by integrating plant risk monitoring data with dynamic PRA methods incorporating aging and degradation. Several online, non-destructive approaches have been developed for diagnosing plant component conditions in nuclear industry, i.e., condition indication index, using vibration analysis, current signatures, and operational history [1]. In this work the component performance measures at U.S. commercial nuclear power plants (NPP) [2] are incorporated within the various dynamic PRA methodologies [3] to provide better estimates of probability of failures. Aging and degradation is modeled within the Level-1 PRA framework and is applied to several failure modes of pumps and can be extended to a range of components, viz. valves, generators, batteries, and pipes.

  4. Environmental status of plant-based industries. Biomass and bio-materials; Bilan environnemental des filieres vegetales. Biomasse et biomateriaux

    Energy Technology Data Exchange (ETDEWEB)

    Vindimian, E; Boeglin, N; Houillon, G; Osset, Ph; Vial, E; Leguern, Y; Gosse, G; Gabrielle, B; Dohy, M; Bewa, H; Rigal, L; Guilbert, St; Cesar, G; Pandard, P; Oster, D; Normand, N; Piccardi, M; Garoux, V; Arnaud, L; Barbier, J; Mougin, G; Krausz, P; Pluquet, V; Massacrier, L; Dussaud, J

    2005-07-01

    The French agency of environment and energy mastery (Ademe) and the agency of Agriculture for chemistry and energy (Agrice) have jointly organized these technical days about the potentialities of plant-based products in front of the big environmental stakes of the diversification of energy sources, the development of new outputs for agriculture and the opening of new fields of industrial innovation. This document gathers the articles and transparencies of the presentations given during these 2 days of conference: 1 - Biomass and life cycle analysis (LCA) - impacts and benefits: introduction to LCA (E. Vindimian), keys to understand this environmental evaluation tool (N. Boeglin); environmental status of plant-based industries for chemistry, materials and energy: LCA knowledge status, plant versus fossil (G. Houillon), detailed analysis of 2 industries: agro-materials and bio-polymers (J. Payet); example of environmental and LCA studies: energy and greenhouse gas statuses of the biofuel production processes (P. Osset, E. Vial), LCA of collective and industrial wood-fueled space heating (Y. Leguern), contribution and limitations of LCA for plant-based industries (G. Gosse, B. Gabrielle), conclusion of the first day (M. Dohy). 2 - Biomass and materials: a reality: biomaterials in the Agrice program (H. Bewa), plant-derived materials: resources, status and perspectives (L. Rigal); biopolymers: overview of the industrial use of biopolymers: materials and markets, applications (S. Guibert), degradation mechanisms of biopolymers used in agriculture: biodegradability, eco-toxicity and accumulation in soils (G. Cesar, P. Pandard), present and future regulatory framework: specifications and methods of biodegradability evaluation of materials for agriculture and horticulture (D. Oster), standardization: necessity and possibilities (N. Normand); vegetable fibers and composite materials: market of new vegetable fiber uses (M. Piccardi, V. Garoux), vegetable particulates and

  5. The refining industry and the future of the fuel oils; L'industrie du raffinage et le devenir des fiouls lourds

    Energy Technology Data Exchange (ETDEWEB)

    Soleille, S

    2004-01-15

    The fuel oils consumption decrease in France since 1970, because of the two petroleum crisis, the nuclear energy competition and the air pollution. The fuel oils industry is then looking other export possibilities. This report aims to offer a first approach of the problem and presents the main challenges. The first part is devoted to the technical context (definition, production and outlet. The second part presents the environmental context and the fuel oils market. In the third part the market is studied at the world scale, in the fourth at the french scale and in the fifth at the scale of other countries as United States, Japan and european Union. A synthesis tables is given in the last part to compare and propose some hypothesis concerning the future of fuel oils and the french refining industry. (A.L.B.)

  6. Development and training for the professional of the gas distribution industry in Brazil; Formation des professionnels de l'industrie de la distribution du gaz au Bresil

    Energy Technology Data Exchange (ETDEWEB)

    Hatsumi Nagato, D. [Workout Energy Business (Brazil)

    2000-07-01

    This work will present a Training and Development model for professionals of the gas distribution industry. Today's there are not schools developing gas related subjects. It's important to give to the future gas man, the knowledge needed to develop their activities. This can be achieved by focusing on criteria based on The Competency Concept and Learning Organization. To develop professional 'competency' we consider this tree of basic points: to know, to know how to do and wish to do ( willing ). We are going to present the 'minimum' 'competences' required for gas distribution companies and the methods used to qualify people for emergent gas industries, considering basically four professionals groups: workers, technicians, engineers and managers. (author)

  7. Concept and design of a virtual reality work environment for industrial designers; Konzeption und Entwurf eines VR Arbeitsplatzes im Bereich des Industrial Design

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, T.; Bruder, R. [Universitaet Essen (Germany). Institut fuer Ergonomie und Designforschung

    2002-07-01

    This concept of a working environment for industrial designers is based on the use of Virtual Reality. The project aims at making the design process using new technologies just as intuitive as the work involving traditional tools. Basis of the development is a human centered principle, not the concentration on available technologies. The project was developed in cooperation with the Fraunhofer Gesellschaft (Institute for media communication) in Sankt Augustin, Germany. (orig.)

  8. The energy industries reorganization in the economic globalization; La restructuration des industries de l'energie dans la mondialisation economique

    Energy Technology Data Exchange (ETDEWEB)

    Amouroux, J.M

    2003-07-01

    The author wonders on the energy supply evolution since thirty years and more specially the fossil fuels industries reconstruction. The energy panorama has been completely modified by a serial of processes which stopped the nuclear energy expansion and replaced the fossil fuels in the front of the energy scene. The processes are examined to evaluate the consequences of theses transformations on the model of economic development developed by the capitalism. (A.L.B)

  9. The part of the international investments in the Russian petroleum industry; La place des investissements internationaux dans l'industrie petroliere russe

    Energy Technology Data Exchange (ETDEWEB)

    Locatelli, C

    2004-03-01

    The ''russian risk'' is important for the international petroleum companies, in spite of the creation of the TNK-BP joint venture. The investment in the petroleum domain face different and contradictory interests in function of the economic implied actors. To analyze the situation the author discussed the russian petroleum industry as an ''unfinished model'', and how the place for the international investments is limited. (A.L.B.)

  10. The gas industry in Brazil and the new regulatory framework; L'industrie du gaz au Bresil et le nouveau cadre des reglementations

    Energy Technology Data Exchange (ETDEWEB)

    Schwyter, A.A. [Comgas, Cia. de Gas de Sao Paulo (Brazil)

    2000-07-01

    In the last tem years many things have changes in the economic and political environment in the world, especially in Brazil. The new federal government elected in 1994 has started a new economic program and one of the most important points is to reduce government interference in the economy. For this reason, the Federal Constitution was changed and now private companies can operate in the natural gas upstream and downstream sectors. The aim of this policy is to increase efficiency in the energy sector with more investment and better prices. Brazil is now facing a new challenge, which is to establish a complete regulatory framework for the gas industry, for its development, with private as well as state owned companies. The purpose of this work is to study the main characteristics of the Brazilian natural gas sector and how to set up regulatory issues to service it. The Brazilian Natural Gas Industry has specific characteristics, very different from other countries', even from those in Latin America. It is necessary, in order to more adequately develop the industry: new suppliers, guaranty of supply, definition of open access, definition of concession models, setting the role of the state and federal powers, transportation systems and the development of a gas network, definition of exports and imports, production, safety, product quality and service, principle of tariffs and prices and all those aspects which are not regulated yet. (author)

  11. NIR Techniques Create Added Values for the Pellet and Biofuel Industry

    Energy Technology Data Exchange (ETDEWEB)

    Lestander, Torbjoern A. [Swedish Univ of Agricultural Science, Umeaa (Sweden). Unit of Biomass Technology and Chemistry; Johnsson, Bo; Grothage, Morgan [Casco Adhesives AB, Sundsvall (Sweden)

    2006-07-15

    Pelletizing of biomass as biofuels increases energy density, improves storability and reduces transport costs. This process is a major key factor in the transition from fossil fuels to renewable biomass refined as solid biofuels. The fast growing pellet industry is today producing more than 1.2 Gg wood Pellets in Sweden - one of the leading nations to utilize bioenergy in its energy mix. The multitude of raw biomaterials available for fuel pellet production and their widely different characteristics stress the need for rapid characterization methods. A suitable technique for characterization of variation in biomaterials is near infrared (NIR) spectrometry. NIR radiation interacts with polar molecules and especially with structural groups O-H as in water, C-H as in biomass, but also with C-O bonds and C=C double bonds frequently found in biomass. Biomass contains mostly the atoms C, O and H. This means that transmittance or reflectance in the NIR wavelength region covers most of the covalent bonds in biomass, except for the C-C bonds in carbon chains. The NIR technique is also developed for on-line measurement in harsh industrial conditions. Thus, NIR techniques can be applied for on-line and real time characterization of raw biomass as well as in the refinement process of biomass into standardized solid biofuels. Spectral patterns in the NIR region contain chemical and physical information structure that together with reference parameters can be modeled by multivariate calibration methods to obtain predictions. These predictions can be presented to the operators in real time on screens as charts based on multivariate statistical process controls. This improves the possibilities to overview the raw biomass variation and to control the responses of the treatments the biomass undergo in the pelletizing process. The NIR-technique is exemplified by a 23-factorial experiment that was carried out in a pellet plant using sawdust as raw material to produce wood Pellets as

  12. Techniques de combustion Combustin Techniques

    Directory of Open Access Journals (Sweden)

    Perthuis E.

    2006-11-01

    Full Text Available L'efficacité d'un processus de chauffage par flamme est étroitement liée à la maîtrise des techniques de combustion. Le brûleur, organe essentiel de l'équipement de chauffe, doit d'une part assurer une combustion complète pour utiliser au mieux l'énergie potentielle du combustible et, d'autre part, provoquer dans le foyer les conditions aérodynamiques les plus propices oux transferts de chaleur. En s'appuyant sur les études expérimentales effectuées à la Fondation de Recherches Internationales sur les Flammes (FRIF, au Groupe d'Étude des Flammes de Gaz Naturel (GEFGN et à l'Institut Français du Pétrole (IFP et sur des réalisations industrielles, on présente les propriétés essentielles des flammes de diffusion aux combustibles liquides et gazeux obtenues avec ou sans mise en rotation des fluides, et leurs répercussions sur les transferts thermiques. La recherche des températures de combustion élevées conduit à envisager la marche à excès d'air réduit, le réchauffage de l'air ou son enrichissement à l'oxygène. Par quelques exemples, on évoque l'influence de ces paramètres d'exploitation sur l'économie possible en combustible. The efficiency of a flame heating process is closely linked ta the mastery of, combustion techniques. The burner, an essential element in any heating equipment, must provide complete combustion sa as to make optimum use of the potential energy in the fuel while, at the same time, creating the most suitable conditions for heat transfers in the combustion chamber. On the basis of experimental research performed by FRIF, GEFGN and IFP and of industrial achievements, this article describesthe essential properties of diffusion flames fed by liquid and gaseous fuels and produced with or without fluid swirling, and the effects of such flames on heat transfers. The search for high combustion temperatures means that consideration must be given to operating with reduced excess air, heating the air or

  13. Gestion des risques, valorisation et stratégie : applications aux industries agro-alimentaire et de transport aérien

    OpenAIRE

    Hassane Amadou, Rahila

    2014-01-01

    Ce travail de recherche apporte des éléments de compréhension supplémentaires sur l’impact des stratégies de gestion des risques sur la valeur et sur la stratégie des entreprises. Une première analyse examine un échantillon de 378 observations d’entreprises du secteur agroalimentaire sur 5 ans. Il ressort de cette analyse que l’intensité d’utilisation des produits dérivés pour couvrir les risques de change, taux d’intérêt et prix des matières premières n’influence pas sensiblement la valeur d...

  14. Perceptions of industrial and nuclear risks. Stakes, negotiations and social development of levels of risk acceptance; Perceptions des risques industriels et nucleaires: enjeux, negociations et construction sociale des seuils d'acception des risques

    Energy Technology Data Exchange (ETDEWEB)

    Bernier, S.Ch

    2007-11-15

    In this thesis we will question the perceptions of industrial risks in the occidental world at the beginning of the 21. century. For this purpose we will try to understand how concepts such as sustainable development, precautionary principle, liability, or even zero-risk bias have progressively developed around a thought model based on the scientific rationality. This model is now undermined by its incapacity to fully address the issues it raises and completely avoid the potential risks. However, despite consistent weaknesses, it remains a reference value moulded by past accidents which have led to the making of laws aiming mainly at defining liability and protecting those who are held liable. Thus, public information becomes a requirement for democracy and the protection of this thought model. In this context, the protagonists at stake are security-conscious, economical and political lobbies that constantly redefine the limits of risk acceptance. We come to the realization that our lifestyle and value system remain unchallenged even though undergoing a crisis. The specificity of this research lies into the importance we give to the local approach, dealing with registered Seveso sites and nuclear plants located in Indre et Loire. We have polled five categories of respondents through interviews or questionnaires in order to understand their opinion regarding situations involving technological risks. The result of this survey helps us understand and set the levels of risk acceptance that they define with regard to the industrial risks and show the complexity of a situation involving political stakes, environmental pressures, a profit-driven economy and security constraints, in a vague and complex context. This work gives us a contrasted picture of today's perceptions of risks. (author)

  15. Geophysical Well Logs Applied to Geothermal Resource Evaluation Application des diagraphies à l'évaluation des ressources géothermiques

    Directory of Open Access Journals (Sweden)

    Fertl W. H.

    2006-11-01

    Full Text Available Well logging in the petroleum industry has been developed over five decades into a mature industry, whereas geothermal well logging is a relatively new enterprise. Fundamental differences also occur in the geologic environments and key objectives of both logging applications. Geothermal reservoirs are frequently in fractured igneous and metamorphic rocks, which contain hot water or stem at temperature exceeding 150°C. The discussion focuses on present day logging technology, geologic and reservoir engineering objectives, and qualitive and quantitative formation interpretation techniques for geothermal resource evaluation. Specific field case studies illustrate the interpretive state-of-the-art, including examples from the Geysers dry steam field in the Imperial Valley of California, hot water fields in California, Nevada, and Idaho, and the LASL Hot Dry Rock test project in the Valles Caldera of New Mexico. Les diagraphies dans les forages pétroliers ont atteint leur maturité, alors que le contrôle diagraphique des sondages géothermiques est une entreprise relativement nouvelle. Des différences fondamentales apparaissent aussi dans les environnements géologiques et dans les objectifs clés des deux types d'applications des diagraphies. Les réservoirs géothermiques se situent souvent dans les roches ignées ou métamorphiques fracturées qui contiennent de l'eau chaude ou de la vapeur à des températures dépassant 150 °C. L'exposé sera concentré sur les techniques actuelles d'enregistrements, les objectifs géologiques et liés à l'exploitation des réserves et sur les techniques qualitatives et quantitatives d'interprétation des formations pour l'évaluation des ressources géothermiques. Quelques cas particuliers illustrent l'état actuel des techniques d'interprétation avec des exemples pris dans le champ de vapeur sèche des geysers dans Imperial Valley de Californie, des champs d'eau chaude en Californie, Nevada et Idaho et

  16. Investment risk evaluation techniques: use in energy-intensive industries and implications for ERDA's Industrial Conservation Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-07-13

    The trade-off between risk and rate-of-return in investment evaluations is crucial in assessing the commercial potential of future energy-conservation technologies. The focus of the Industrial Conservation Program at ERDA is to reduce the perceived risks of a given technology to the extent that the private sector will adopt the technology within the normal course of its business operations. These perceived risks may emanate from technical, institutional, or commercial uncertainties, or in many cases they may result merely from a company's or industry's lack of previous experience with a particular technology. Regardless of the source of the risk surrounding a project, the uncertainty it poses to the private sector will serve to inhibit decisions to invest. This study evaluates the treatment of risk in capital investments in certain energy-intensive industries which are the primary targets of ERDA's Industrial Conservation Program. These risks evaluation considerations were placed within a context that includes capital budgeting practices and procedures, organizational considerations, and basic rate-of-return evaluation procedures in the targeted energy-intensive industries (petroleum, chemicals, paper, textiles, cement, food processing, aluminum, steel, glass, and agriculture).

  17. Le dysfonctionnement socio-spatial des grands ensembles en Algérie: technique de l’analyse wayfinding par méthode “movement traces” et l’analyse morphologique (syntaxe spatiale par logiciel “depthmap”

    Directory of Open Access Journals (Sweden)

    Amara Hima

    2018-03-01

    Full Text Available Résumé La technique de l’analyse syntaxique de la visibilité (Visibility Graph Analysis – VGA et de l’accessibilité (All Line Analysis – ALA par logiciel “DepthMap©(UCL, Londres” et l’analyse du dysfonctionnement wayfinding par méthode “movement traces”, sont utilisées dans ce papier afin de développer un modèle d’analyse et d’investigation de l’impact des changements spatiaux sur le dysfonctionnement socio-spatial du wayfinding, ainsi sur la reproduction urbaine, notamment les transformations des façades et l’appropriation des espaces extérieurs dans les grands ensembles en Algérie. Nous donnons ici le cas d’étude de la cité 1000 logt-Biskra et la cité 500 logt-M’sila. Afin de vérifier cette hypothèse, un modèle d’analyse hybride a été développé par croisement des résultats d’analyses des deux techniques. Par conséquent, le schéma de l’interférence montre que la majorité des piétons préfèrent parcourir les axes courts et droits — caractérisés par une forte propriété syntaxique de visibilité et d’accessibilité (l’intégration, la connectivité et l’intelligibilité — en directions des équipements adjacents et aux milieux des deux cités. Ces itinéraires ont un impact sur les transformations des façades et l’appropriation des espaces extérieurs. Le modèle développé promet de futures recherches sur le plan de la quantification, la modélisation et la simulation du processus de la reproduction urbaine, notamment par les automates cellulaires.

  18. Repenser la définition des aides techniques en éducation / Rethinking the definition of assistive technology in education

    Directory of Open Access Journals (Sweden)

    Hajer Chalghoumi

    2012-11-01

    Full Text Available En éducation, un nombre croissant d’élèves avec incapacités ont recours aux aides techniques. Parallèlement, une littérature récente mais de plus en plus abondante étudie ce concept. En dépit de cet intérêt grandissant tant au niveau de la recherche que de la pratique liée à ces technologies, plusieurs indices soulignent la difficulté de distinguer entre ce concept et celui de technologies de l’information et de la communication (TIC notamment en éducation. Les aides techniques sont-elles un concept distinct ou une variante des TIC? Quelles sont les conséquences d’une telle confusion conceptuelle ? Comment peut-on différencier ces deux concepts ? L’objectif du présent article est d’apporter des éléments de réponse à ces questions. In education, an increasing number of students with disabilities make use of assistive technologies (AT. Meanwhile, a recent but growing literature studies this concept. Despite this interest both in research and practice related to these technologies, several clues point to the difficulty of distinguishing it from and the information and communication technology (ICT, particularly in education. Are AT a distinct concept or a variation of ICT? What are the consequences of such a confusion? How can we differentiate these two concepts? The purpose of this article is to provide some answers to these questions.

  19. Photonique des Morphos

    CERN Document Server

    Berthier, Serge

    2010-01-01

    La photonique est déjà présente dans notre vie quotidienne, et on attend maintenant que la manipulation des photons permette aussi le traitement logique des informations. Cependant, l’élément de base qui permet cette manipulation de la lumière, le cristal photonique, est d’une réalisation complexe et mal contrôlée. Dans la course à la maîtrise de la lumière, les structures photoniques naturelles ont beaucoup à nous apprendre. C’est ce que nous montre Serge Berthier qui étudie dans ce livre la structure des écailles des Morphos. Tenant compte de l’essor récent des approches biomimétiques, il présente de manière détaillée plus de dix-huit techniques expérimentales utilisées pour ses analyses, ainsi que les diverses approches théoriques développées pour la modélisation de structures multi-échelles complexes. Première étude quasi-exhaustive des structures fines d’un genre et des propriétés optiques ainsi que colorimétriques générées, ce livre fournit aux entomologiste...

  20. Reform of the energy supply law seen from the point of view of industry. Reform des Energiewirtschaftsgesetzes aus industrieller Sicht

    Energy Technology Data Exchange (ETDEWEB)

    Boeke, E; Heller, W [Bundesverband der Deutschen Industrie e.V., Koeln (Germany). Abt. Energiepolitik

    1991-12-01

    From the point of view of the industry there are two central tasks for energy policy: 1. The German industry has to be supplied with energy at internationally competitive prices. Of the three aims of energy policies (secure, moderately-priced and low-pollutant) the price aim is in Germany in the international comparison today least achieved. 2. Policy always tends to solve problems in the energy sector with regulating interventions. An example from the recent past is the power supply law of 1990 with which the way to political electricity pricing was opened. But the precept for the Internal European Market has to be deregulation as only in this way the larger market can develop its efficiency to the full. Also for the reform of the economic laws concerning the energy sector these two central aims have to be taken into consideration. (orig./UA).

  1. Space heating in buildings: thermal diagnosis of an industrial building; Chauffage des batiments: bilan thermique d`un batiment industriel

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, R.

    1996-12-31

    The various heat transfer equations used for calculations in thermal diagnosis of an industrial building are reviewed: calculation of the heat losses through walls as a function of building materials, calculation of the energy consumption for heating fresh air (as a function of the air pollution rate in the building), calculation of the total heat losses, the heating energy demand and the annual energy consumption. Data concerning building materials characteristics, insulation and heating loads in the various regions of France, are also presented

  2. Cost-benefit analysis of the industrial evaluations employing radioactive tracer techniques in the sugar-cane industry

    International Nuclear Information System (INIS)

    Aguila, D.; Jerez, P.F.

    1998-01-01

    A practice with radioactivity is justifiable if the benefit that she brings is greater than the detriment to the health that provokes. This is achieved with an optimization of the radiological protection on the base of the principle ALARA (the dose must be at botommost level that reasonably could be reached). The cost-benefit analysis helps to take a decision of practice optimized to use. Based on the cost-benefit criterion in the framework of the industrial radioprotection, was accomplished an industrial evaluations study employing 99mT c and 1 31 I in industry Cuban sugar-bowl. The results of the analysis demonstrated that the use of the 99mT c as radiotracer is the better option to take

  3. Taking advantage of the Kyoto mechanisms in the natural gas industry; Benefices des mecanismes de Kyoto pour l'industrie du gaz naturel

    Energy Technology Data Exchange (ETDEWEB)

    Janssen, J. [Institute for Economy and the environment at the University of St. Gallen, IWOe-HSG (Switzerland)

    2000-07-01

    The Kyoto Protocol has laid the basis of global markets for greenhouse gas emission reductions. By means of the Kyoto Mechanisms Joint Implementation, the Clean Development Mechanism and International Emissions Trading it will be possible to produce abroad and trade internationally the greenhouse gas emission reductions needed to satisfy cost-efficiently the respective demand of industrialized countries. The paper analyses options available in the natural gas sector for realizing Joint Implementation and Clean Development Mechanism projects. Furthermore, it examines strategies that might be economically viable for companies operating in the natural gas sector for taking advantage of the Kyoto Mechanisms. (author)

  4. Technique of Substantiating Requirements for the Vision Systems of Industrial Robotic Complexes

    Directory of Open Access Journals (Sweden)

    V. Ya. Kolyuchkin

    2015-01-01

    Full Text Available In references, there is a lack of approaches to describe the justified technical requirements for the vision systems (VS of industrial robotics complexes (IRC. Therefore, an objective of the work is to develop a technique that allows substantiating requirements for the main quality indicators of VS, functioning as a part of the IRC.The proposed technique uses a model representation of VS, which, as a part of the IRC information system, sorts the objects in the work area, as well as measures their linear and angular coordinates. To solve the problem of statement there is a proposal to define the target function of a designed IRC as a dependence of the IRC indicator efficiency on the VS quality indicators. The paper proposes to use, as an indicator of the IRC efficiency, the probability of a lack of fault products when manufacturing. Based on the functions the VS perform as a part of the IRC information system, the accepted indicators of VS quality are as follows: a probability of the proper recognition of objects in the working IRC area, and confidential probabilities of measuring linear and angular orientation coordinates of objects with the specified values of permissible error. Specific values of these errors depend on the orientation errors of working bodies of manipulators that are a part of the IRC. The paper presents mathematical expressions that determine the functional dependence of the probability of a lack of fault products when manufacturing on the VS quality indicators and the probability of failures of IRC technological equipment.The offered technique for substantiating engineering requirements for the VS of IRC has novelty. The results obtained in this work can be useful for professionals involved in IRC VS development, and, in particular, in development of VS algorithms and software.

  5. Comparaison de deux techniques d'identification des souches de levures de vinification basées sur le polymorphisme de l'ADN génomique: réaction de polymérisation en chaine (PCR et analyse des caryotypes (électrophorèse en champ pulsé

    Directory of Open Access Journals (Sweden)

    Isabelle Masneuf-Pomarède

    1994-06-01

    Full Text Available Une nouvelle technique de la biologie moléculaire, la réaction de polymérisation en chaine (PCR permet l'identification des souches de levures de vinification. Mise en oeuvre directement sur levures entières, elle permet d'obtenir des profils variables selon les souches, par l'amplification de séquences d'ADN génomique. Utilisée sur lies, la PCR constitue un outil rapide et sensible pour le contrôle d'implantation des levains en vinification. Cependant le pouvoir discriminant de la PCR est inférieur à celui de l'électrophorèse en champ pulsé pour la caractérisation des souches de levures indigènes. Elle doit être considérée comme une technique complémentaire d'identification des souches de S. cerevisiae.

  6. Contribution des TICs à l'abandon des mutilations génitales ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Contribution des TIC à l'abandon des MGF en Afrique de l'Ouest francophone : rôle des jeunes citoyennes; rapport technique no. 5 (rapport technique final), 18 octobre 2008 - 31 mars 2009. Download PDF. Related content. New website will help record vital life events to improve access to services for all. A new website ...

  7. Prevention of the causes and consequences of a criticality accident - measures adopted in France; Prevention des causes et des consequences d'un accident de criticite - solutions adoptees en France

    Energy Technology Data Exchange (ETDEWEB)

    Fruchard, Y.; Lavie, J.M

    1966-07-01

    The question of safety in regard to criticality accident risks has two aspects: prevention of the cause and limitation of the consequences. These two aspects are closely connected. The effort devoted to prevention of the causes depends on the seriousness of the possible human psychologic and economic consequences of the accident. The criticality accidents which have occurred in the nuclear industry, though few in number, do reveal the imperfect nature of the techniques adopted to prevent the causes, and also constitute the only available realistic basis for evaluating the consequences and developing measures to limit them. The authors give a analysis of the known causes and consequences of past criticality accidents and on this basis make a number of comments concerning: the validity of traditional safety criteria, the probability of accidents for different types of operations, characteristic accidents which can serve as models, and the extent of possible radiological consequences. The measures adopted in France to limit the consequences of a possible criticality accident under the headings: location, design and lay-out of the installations, accident detection, and dosimetry for the exposed personnel, are briefly described after a short account of the criteria used in deciding on them. (author) [French] La surete relative aux risques d'accidents de criticite presente deux aspects: la prevention des causes et les parades aux consequences. Ces deux aspects sont tres lies. L'effort consenti a la prevention des causes decoule de l'importance des consequences humaines economiques et psychologiques possibles d'un eventuel accident. Les accidents de criticite survenus dans l'industrie nucleaire, malgre leur rarete, d'une part devoilent les imperfections des techniques de prevention des causes, d'autre part constituent la seule base realiste disponible d'evaluation des consequences et de mise au point des parades a ces consequences

  8. Prevention of the causes and consequences of a criticality accident - measures adopted in France; Prevention des causes et des consequences d'un accident de criticite - solutions adoptees en France

    Energy Technology Data Exchange (ETDEWEB)

    Fruchard, Y; Lavie, J M

    1966-07-01

    The question of safety in regard to criticality accident risks has two aspects: prevention of the cause and limitation of the consequences. These two aspects are closely connected. The effort devoted to prevention of the causes depends on the seriousness of the possible human psychologic and economic consequences of the accident. The criticality accidents which have occurred in the nuclear industry, though few in number, do reveal the imperfect nature of the techniques adopted to prevent the causes, and also constitute the only available realistic basis for evaluating the consequences and developing measures to limit them. The authors give a analysis of the known causes and consequences of past criticality accidents and on this basis make a number of comments concerning: the validity of traditional safety criteria, the probability of accidents for different types of operations, characteristic accidents which can serve as models, and the extent of possible radiological consequences. The measures adopted in France to limit the consequences of a possible criticality accident under the headings: location, design and lay-out of the installations, accident detection, and dosimetry for the exposed personnel, are briefly described after a short account of the criteria used in deciding on them. (author) [French] La surete relative aux risques d'accidents de criticite presente deux aspects: la prevention des causes et les parades aux consequences. Ces deux aspects sont tres lies. L'effort consenti a la prevention des causes decoule de l'importance des consequences humaines economiques et psychologiques possibles d'un eventuel accident. Les accidents de criticite survenus dans l'industrie nucleaire, malgre leur rarete, d'une part devoilent les imperfections des techniques de prevention des causes, d'autre part constituent la seule base realiste disponible d'evaluation des consequences et de mise au point des parades a ces consequences. Les auteurs presentent une analyse des

  9. The use of pathological and histopathological techniques in the diagnosis of peste des petits ruminants in India

    Directory of Open Access Journals (Sweden)

    Harshad C. Chauhan

    2011-01-01

    Full Text Available The authors report on an outbreak of peste des petits ruminants (PPR among sheep and goats in the Province of Gujarat, India. Clinical signs observed during outbreaks were typical of PPR. Predominant signs were severe diarrhoea, dyspnoea, mucopurulent discharge from the eyes and nose, erosive rhinitis, necrotic ulcers in the mouth, on the dental pad, tongue, upper and lower lips, fever and depression. Common post-mortem findings included congestion, red hepatisation, raised patches of emphysema in the lungs, haemorrhages and froth exudates in the trachea, severe enteritis and streaks of haemorrhages in the intestine, enlargement and petechial haemorrhages in the spleen and oedema and inflammatory lesions in the mesenteric lymph nodes. Spectacular histopathological changes were observed in the lungs, intestine, spleen, mesenteric lymph nodes, liver and kidneys. Clinical, gross and histopathological lesions and haematological changes were suggestive of PPR, which was further confirmed by detection of PPR viral antigen in clinical samples, as well as post-mortem tissues using the sandwich enzyme-linked immunosorbent assay (s‑ELISA.

  10. Recycling of modules: the industry meets the demand; Recyclage des modules: la filiere s'organise

    Energy Technology Data Exchange (ETDEWEB)

    Houot, G.

    2011-04-15

    In a few years the number of photovoltaic plants to be decommissioned will begin to grow dramatically which will generate a huge need for the collect and recycling of old solar panels. A European association PV-Cycle proposes to set up a dedicated waste processing industry that will be able to recycle up to 85% of the wastes from old solar panels. 23 spots for recovering solar panels have been installed throughout Europe, the recovery of about 1000 to 1500 tons of equipment is expected for 2011. The German Sunicon enterprise has set up an automated process that combines thermal, mechanical and chemical processes in order to allow an almost complete recycling of glass and silicon into the solar panel industry. In a near future the capacity of Sunicon will pass from 800 tons to 20.000 tons a year. The American company First Solar organizes itself the recovery and recycling of the CdTe solar panels it manufactured. (A.C.)

  11. Rehabilitation of river sediments contaminated by heavy metals from tanning industries using the phytoextraction technique

    Science.gov (United States)

    Beltrá Castillo, Juan Carlos; García Orenes, Fuensanta; Mora Navarro, José; Murcia Navarro, Francisco Jose; Zornoza Belmonte, Raúl; Faz Cano, Ángel; Gómez-Garrido, Melisa

    2017-04-01

    Leather tanning is an industrial sector of great tradition in Spain that has progressively evolved until it has reached a high degree of technification in the present. However, in its early days, the leather tanning industry has always been considered a dirty and polluting activity, mainly due to the water spills that ended up in the river channels. The Guadalentin Valley between Lorca and Murcia (SE Spain) is characterised by intensive crop and pig production, and an extensive agroalimentary and leather tannery industry. These anthropogenic sources have released salts and metals such as copper (Cu), zinc (Zn) and chromium (Cr) into Guadalentin river. Up to 2003, wastewater was discharged directly to the dry river, immediately upstream of the urban nucleus of Lorca, without any previous treatment. It contained high concentrations of inorganic salts and heavy metals (Cu, Zn and Cr). Spills, in some events, had a flow of 10 000 m3 d-1, with concentration of Cr over 500 mg L-1. Phytoremediation is a sustainable alternative that allows the environmental rehabilitation of fluvial dry sediments through the transfer of heavy metals from the contaminated soils to the native vegetation present. Atriplex halimus, salsola oppositifolia, suaeda vera and tamarix africana were the most representative autochthonous phytoextractor species that were planted to study the degree of decontamination of dry river sediments before planting and 12 months after planting. The sediments characterization was done by a sampling grid of 40 000 m2 (500 m x 8 m) where samples were taken at 3 depths (0-20 cm, 20-50 cm and 5-100 cm) every 50 m. A vegetation study was carried out by random plots of 10 m x 10 m. The results indicated that after 12 months the vegetation cover increased between 35% and 70%. The degree of contamination of Cu, Zn and Cr of the river dry sediments decreased slightly, being the atriplex halimus the plant specie that presented the highest value of the bioaccumulation factor

  12. Air pollution emission reduction techniques in combustion plants; Technique de reduction des emissions de polluants atmospheriques dans les installations de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Bouscaren, R. [CITEPA, Centre Interprofessionnel Technique d`Etudes de la Pollution Atmospherique, 75 - Paris (France)

    1996-12-31

    Separating techniques offer a large choice between various procedures for air pollution reduction in combustion plants: mechanical, electrical, filtering, hydraulic, chemical, physical, catalytic, thermal and biological processes. Many environment-friendly equipment use such separating techniques, particularly for dust cleaning and fume desulfurizing and more recently for the abatement of volatile organic pollutants or dioxins and furans. These processes are briefly described

  13. Application of cost mathematical models to the determination of investments in the petroleum industry; Application des modeles mathematiques de cout a la determination des investissements dans l`industrie petroliere

    Energy Technology Data Exchange (ETDEWEB)

    Fournier, G; Ecole Nationale Superieure du Petrole et des Moteurs (ENSPM), 92 -Rueil-Malmaison (France); Univ. de Bourgogne, 21- Dijon (France)

    1997-05-01

    It is today of paramount importance to realistically forecast the cost and time required to design and manufacture a given product, from the very first phase of the project. Furthermore, with the increasingly rapid development of technology, it is often impossible to draw a direct parallel with existing, well known products Mathematical models of cost, and MAP models in particular, have been developed to meet this need. Although one may still refer to former products, they do not automatically have to be `analogous` to the product under consideration, because these methods use `universal relationship` between cost, weight, technology, performance and reliability, and also the nature and experience of the firm manufacturing the product. The purpose of this thesis is to demonstrate the pertinence, and more importantly the potential, of mathematical models of cost for the oil and gas industry, from exploration and production to refining, petrochemicals, and internal combustion engines. After a theoretical examination of estimation methods and a classification of existing ones, emphasis is placed on the logical aspect of these models. In addition, the complementarity between these tools and certain fields such as project management is pointed out, for example with respect to value control. The last chapter of the thesis is devoted to case studies. It aims chiefly at comparing theory with practice in order to identify the limits of mathematical models of cost so that they can be used judiciously. (author). 159 refs.

  14. Cleansing of industrial sites: the Charbonnages de France example; Depollution des sites industriels: l'exemple de Charbonnages de France

    Energy Technology Data Exchange (ETDEWEB)

    Lagarde, R.; Guise, Y.; Gobillot, R. [Charbonnages de France, 92 - Rueil Malmaison (France); Bonin, H. [GRS Valtech, 78 - Carrieres sur Seine (France)

    2004-09-01

    Charbonnages de France, the French national coal board, has planned to stop its mining activities. Todays, its main goal concerns the remediation of its polluted mining and industrial sites. This article presents the cleansing techniques used at the Auby coking plant site for the removal of the polycyclic aromatic hydrocarbons (PAH) from the soil: protection of the aquifer, thermal desorption of the polluted earth, oxidation of the evaporated pollutants, valorization of the processed earth. (J.S.)

  15. Evaluation des bassins par modélisation intégrée en deux dimensions des transferts techniques, de l'écoulement des fluides, de la genèse et de la migration des hydrocarbures Basin Evaluation by Integrated Two-Dimensional Modeling of Heat Transfer, Fluid Flow, Hydrocarbon Generation, and Migration

    Directory of Open Access Journals (Sweden)

    Chenet P. Y.

    2006-11-01

    Full Text Available Le modèle de bassin exposé dans cet article décrit les phénomènes physiques et chimiques qui contrôlent la formation d'accumulations commerciales, dans le cadre évolutif d'un bassin sédimentaire affecté par la subsidence : transfert de chaleur, compaction et écoulement de l'eau, génèse des hydrocarbures, migration diphasique de l'eau et des hydrocarbures. Le modèle tient compte des variations de conductivité et des phénomènes thermiques transitoires pour reconstituer les paléo-températures. Des validations quantitatives de la reconstitution des paléo-températures et du modèle cinétique de formation des hydrocarbures peuvent être obtenues par comparaison avec les températures actuelles et les données géochimiques. Les écoulements et les surpressions induits par la compaction sont décrits en couplant une loi de compaction avec la loi de Darcy, classique pour les écoulements de l'eau, en ajoutant un critère de fracturation hydraulique naturelle. Ceci permet de modéliser les pressions anormales dans des séquences deltaïques récentes (delta de la Mahakam, comme dans des bassins liés à des rifts anciens (mer du Nord. Une adaptation de la loi de Darcy aux écoulements diphasiques permet de reproduire la migration primaire et la migration secondaire. En particulier, le modèle permet d'étudier le rôle des pressions anormales et l'influence des failles sur la migration et le piégeage. Nos résultats confirment que les modèles de bassins peuvent contribuer à synthétiser les données géologiques, géophysiques et géochimiques dans un schéma cohérent. En précisant l'évaluation pétrolière, ces modèles constituent une des principales voies pour améliorer l'efficacité de l'exploration. The basin model discussed in this paper describes the physical and chemical phenomena that control the formation of commercial accumulations of hydrocarbons in the moving framework of a subsiding sedimentary basin : heat

  16. Valorization of used tyres as fuel substitute in cement industry; Valorisation des pneus usages comme combustible de substitution en cimenterie

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1999-03-01

    According to the French syndicate of cement industry, more than 350000 t of worn tyres are produced each year in France, among which only 143000 t are reused in retreading, exported as used tyres or valorized in cement industry. The rest is generally tipped or burnt in the open-air. In cement kilns, the organic matters of tyres are completely burnt while the metal belts supply the necessary amount of iron to the cement composition. The combustion of tyres produces no black smoke, no smell and no ash and has no significant influence on the effluents of cement factories: gases are directly filtered in the kiln by the important mass of raw materials which acts as quicklime. In 1997, 31500 t of used tyres were burnt in the seven French cement factories over 34 that use this kind of fuel and represents 1.5% of the total energy needs. This substitution ratio could easily reach 10 to 15% without leading to any additional environmental or technical problem. A project of collection and valorization of used tyres has been developed by the French ministry of environment and aims at completely eliminating tyres tipping since July 1, 2002. In order to illustrate the French policy of tyres valorization, two examples of actions are presented in this paper: the first one is carried out by the Michelin manufacturer in order to facilitate the recycling of civil engineering tyres, and the second is carried out by Ciments d`Origny company at the Rochefort factory where tyres are used as fuel substitutes. (J.S.)

  17. Techniques for high dose dosimetry in industry, agriculture and medicine. Proceedings of a symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In radiation processing, it is important that the irradiated products are reliable and safe. For processes that impact directly on public health, dosimetry provides a formal means of regulation. For other applications, measurements are indispensable for process control to improve quality and the measurements have to be standardized. Thus, dosimetry is an essential part of quality standards for radiation processes. In the developing world, establishment of such quality standards is only in the embryonic stage, and the IAEA should and does play a role in the development and implementation of these standards. The IAEA initiated a programme of high dose dosimetry in 1977 to accomplish dose standardization on an industrial scale, to promote dosimetry as a quality control measure in radiation processing, and to help develop new dosimetry techniques. Since dosimetry has such a key role in these processes, the IAEA organized this international symposium to provide a forum for presentation and discussion of up-to-date developments in this field. Since the International Symposium on High Dose Dosimetry for Radiation Processing held in 1990 the field of dosimetry has deepened and broadened. There is a definite shift towards quality assurance, which calls for dependable dosimetry systems with well established traceability to national or international standards. Also, many new applications of radiation have been developed and for these new and innovative dosimetry methods are needed. This symposium has provided a forum for the discussion of many of these developments and consideration of the outstanding issues in these vital areas Refs, figs, tabs

  18. Techniques for high dose dosimetry in industry, agriculture and medicine. Proceedings of a symposium

    International Nuclear Information System (INIS)

    1999-03-01

    In radiation processing, it is important that the irradiated products are reliable and safe. For processes that impact directly on public health, dosimetry provides a formal means of regulation. For other applications, measurements are indispensable for process control to improve quality and the measurements have to be standardized. Thus, dosimetry is an essential part of quality standards for radiation processes. In the developing world, establishment of such quality standards is only in the embryonic stage, and the IAEA should and does play a role in the development and implementation of these standards. The IAEA initiated a programme of high dose dosimetry in 1977 to accomplish dose standardization on an industrial scale, to promote dosimetry as a quality control measure in radiation processing, and to help develop new dosimetry techniques. Since dosimetry has such a key role in these processes, the IAEA organized this international symposium to provide a forum for presentation and discussion of up-to-date developments in this field. Since the International Symposium on High Dose Dosimetry for Radiation Processing held in 1990 the field of dosimetry has deepened and broadened. There is a definite shift towards quality assurance, which calls for dependable dosimetry systems with well established traceability to national or international standards. Also, many new applications of radiation have been developed and for these new and innovative dosimetry methods are needed. This symposium has provided a forum for the discussion of many of these developments and consideration of the outstanding issues in these vital areas

  19. A Simple Refining Technique of Coconut Oil for Small Holder Industries

    Directory of Open Access Journals (Sweden)

    Sugeng Triyono

    2009-04-01

    Full Text Available A simple refining equipment and process for small holder industries of edible coconut oil has beeninvestigated. The equipment consisted of 20-L filtering and NaOH neutralization bottles. Filtration wasintended to remove impurities such as gums and pigment, while neutralization was to remove free fattyacids (FFA and other non-fat materials. In the experiment, the crude coconut oil was found to have impurityof 0.16%, FFA of 8.02%, saponification number of 270, and water content of 0.33%. The results showed thateither granular activated carbon (GAC or zeolite filtration can be chosen individually to remove physicalimpurity. The GAC or zeolite-filtered coconut oil contained impurity less than the SNI standard of 0.05%.In term of FFA; however, the NaOH neutralized coconut oil did not meet the SNI standard of 0.3%. AfterNaOH neutralization, the GAC filtered oil contained 1.20% FFA; while the zeolite filtered oil contained1.32%. These FFA contents were definitely higher than the SNI standard, but could satisfy APCC standardfor grade IV coconut oil which is 5%. The refined coconut oils could also satisfy the SNI standard ofsaponification number which is 196 – 206 at minimum. In term of water content, either the filtered or theneutralized oil could also satisfy the SNI standard of 0.3%. In short, the proposed technique could helpfarmers refine their raw coconut oil, and hopefully improve its marketability.

  20. Atmospheric pollution in the Tula Industrial Corridor studied using a bio monitor and nuclear analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Martinez C, M. A.; Solis, C.; Andrade, E. [UNAM, Instituto de Fisica, Apdo. Postal 20-364, 01000 Mexico D. F. (Mexico); Beltran H, R. I. [Universidad Autonoma del Estado de Hidalgo, Centro de Investigaciones Quimicas, Carretera Pachuca-Tulancingo Km. 4.5, 42184 Pachuca, Hidalgo (Mexico); Issac O, K. [Universidad Autonoma del Estado de Mexico, Facultad de Medicina, Paseo Tollocan s/n, esq. Jesus Carranza, 50120 Toluca, Estado de Mexico (Mexico); Lucho C, C. A. [Universidad Politecnica de Pachuca, Carretera Pachuca-Cd. Sahagun Km. 20, Hidalgo (Mexico); Lopez R, M. C.; Longoria, L. C. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2011-02-15

    This study deals with the application of nuclear analytical techniques to analyze trace elements in the biological monitor Tillandsia usneoides. Biological monitors provides an alternative advantageous way of particulate matter sampling in air pollution studies, since there is no need of special sampling devices, accumulation time can be as long as desired. T. usneoides, which occurs naturally throughout Mexico, was used to monitor air quality of Tula-Vito-Apasco (TVA) industrial corridor at central Mexico. This area is considered one of the critical zones of the country because of atmospheric contaminants high concentration. Particulate matter is regulated by Mexican norms, but its chemical composition is not. Plants were transplanted from a clean environment to four sites at the TVA corridor, and exposed for 12 weeks from February to April 2008. Trace element accumulation of plants was determined by particle induced X-ray emission and neutron activation analysis. Results reveal differences in trace elements distribution among sites in the TVA corridor. Furthermore, anthropogenic elements (S, V) and crustal elements (Ca) in T. usneoides exhibit high levels. Highly toxic elements such as Hg, As and Cr although present at trace levels, showed un enrichment relative to the initial values, when transplanted to the TVA corridor. Results show that monitoring with T. usneoides allows a first approximation of air sources to provide insights of the atmospheric pollution in the TVA corridor. (Author)

  1. Atmospheric pollution in the Tula Industrial Corridor studied using a bio monitor and nuclear analytical techniques

    International Nuclear Information System (INIS)

    Martinez C, M. A.; Solis, C.; Andrade, E.; Beltran H, R. I.; Issac O, K.; Lucho C, C. A.; Lopez R, M. C.; Longoria, L. C.

    2011-01-01

    This study deals with the application of nuclear analytical techniques to analyze trace elements in the biological monitor Tillandsia usneoides. Biological monitors provides an alternative advantageous way of particulate matter sampling in air pollution studies, since there is no need of special sampling devices, accumulation time can be as long as desired. T. usneoides, which occurs naturally throughout Mexico, was used to monitor air quality of Tula-Vito-Apasco (TVA) industrial corridor at central Mexico. This area is considered one of the critical zones of the country because of atmospheric contaminants high concentration. Particulate matter is regulated by Mexican norms, but its chemical composition is not. Plants were transplanted from a clean environment to four sites at the TVA corridor, and exposed for 12 weeks from February to April 2008. Trace element accumulation of plants was determined by particle induced X-ray emission and neutron activation analysis. Results reveal differences in trace elements distribution among sites in the TVA corridor. Furthermore, anthropogenic elements (S, V) and crustal elements (Ca) in T. usneoides exhibit high levels. Highly toxic elements such as Hg, As and Cr although present at trace levels, showed un enrichment relative to the initial values, when transplanted to the TVA corridor. Results show that monitoring with T. usneoides allows a first approximation of air sources to provide insights of the atmospheric pollution in the TVA corridor. (Author)

  2. From the local structure of the catalytic materials to the colloidal macrostructure of systems of the petroleum industry; De la structure locale des materiaux catalytiques a la macrostructure colloidale des systemes d'interet petrolier

    Energy Technology Data Exchange (ETDEWEB)

    Espinat, D.

    2006-01-15

    The industrial development of new catalysts or adsorbents needs a further knowledge into the structure and texture of these materials. Thus, several techniques must be used in order to deliver complementary information. X-ray diffraction and neutron diffraction provide a precise structural and textural characterisation. X-ray or neutron beam is scattered when crossing the sample; high values of the scattering vector are used for structure determination, while, low values enable texture or macrostructure characterisation of the compound. Heterogeneous catalysts show a large specific area and are made of small particles, close to tenth of nanometers. Thus, crystalline domains are small and the wide angle X-ray scattering shows few Bragg peaks having large full width at half maximum. It becomes difficult, for such materials, to obtain crystallographic information and we have proposed a new approach based on the X-ray diagram simulation according to a structural model of the solid (Precray-Simax software). Several applications have concerned catalysts exhibiting a MoS{sub 2}-type structure, compounds having spinel-like structure, as for instance alumina (catalyst carrier) or zinc aluminate. Zeolites, used as catalysts or adsorbents, have a large specific area with extended crystalline domains. Rietveld refinement technique was used for a better understanding of zeolite stabilisation needed for industrial applications. The use of faujasite-type zeolites for the separation process of para-xylene from C8 aromatics has taken on several works using X-ray and neutron diffraction, gravimetry studies, molecular simulations, in order to describe molecular adsorption on zeolites and to get insight in zeolites selectivity origin. Various colloidal systems, others than catalysts and adsorbents, are often found in petroleum industry, and better knowledge of these materials is truly necessary to advance industrial processes. Small angle X-ray and neutron scattering allow to get

  3. Use o quality management techniques in the frame of scientific studies; Einsatz von Methoden des Qualitaetsmanagements im Rahmen wissenschaftlicher Arbeiten

    Energy Technology Data Exchange (ETDEWEB)

    Kratzsch, A.; Hoelker, M.; Kaestner, W. [Hochschule Zittau/Goerlitz, Zittau (DE). Inst. fuer Prozesstechnik, Prozessautomatisierung und Messtechnik (IPM)

    2010-05-15

    The authors recommend that for safety experiments concerning process engineering, process automation and measurement engineering increased requirements should be implemented with respect to the experimental procedures and the quality of the results. Techniques of quality management (EN ISO 9000 ff) should be applied. Experiences show that the implementation of quality management techniques induces significantly higher transparency of process sequences. A major task should be the long-term backup of experiment documentation and research results.

  4. A contribution to the industrial valorization of tannery waste: the case of cement industry; Contribution a la valorisation industrielle des dechets de tanneries: cas de la cimenterie

    Energy Technology Data Exchange (ETDEWEB)

    Yatribi, A.; Boukhars, L. [Service de l' Environnement, Div. de l' Urbanisme, Province de Kenitra (Morocco); Nejmeddine, A. [Laboratoire d' Ecotoxicologi, Faculte des Sciences Semlalia, Marrakech (Morocco)

    2001-04-01

    The present work addresses the possibility of valorization of tannery waste incineration ashes in the cement industry. To this end, the impact of the addition of ashes at various percentages (0, 5, 10, 15, 20, 25, 30, 35, 40 and 45 % in mass) on some mechanical and physical parameters of cement was examined: normal consistency (%), the beginning of setting (hr), the end of setting (hr), the hot expansion (mm), the resistances to compression and to bending (N/mm{sup 2}) determined on normalized 4 x 4 x 16 cm samples. The impact of the treatment environment (20 deg C and 100 % of relative humidity RH, 30 deg C and 70 % RH, 45 deg C and 45 % RH) was also taken into consideration. The obtained results reveal that the normal consistency, the beginning and the end of setting vary linearly with the quantity of added ashes. Above an addition of ashes of 30 %, the end of setting exceeds the standards demanding a maximum of 10 hours. Additionally, the results indicate that whatever the environment treatment may be, the resistances to compression and to bending increase with the increase of the sample age; they vary inversely to the amount of ash addition. The results allow to conclude that for an ash addition of 15 % and after an ageing of 30 days, the resistance to compression is higher than 40 N/mm{sup 2}, thus allowing the production of CPA 400 cement. These results also allow to conclude that samples kept in a humid environment give the best resistances to compression and to bending, by comparison with those kept in a dry environment. (authors)

  5. Nuclear measurements, techniques and instrumentation industrial applications plasma physics and nuclear fusion. 1980-1994. International Atomic Energy Agency publications

    International Nuclear Information System (INIS)

    1995-04-01

    This catalogue lists all sales publications of the International Atomic Energy Agency dealing with Nuclear Measurements, Techniques and Instrumentation, with Industrial Applications (of Nuclear Physics and Engineering), and with Plasma Physics and Nuclear Fusion, issued during the period 1980-1994. Most publications are in English. Proceedings of conferences, symposia, and panels of experts may contain some papers in other languages (French, Russian, or Spanish), but all papers have abstracts in English. Price quotes are in Austrian Schillings, do not include local taxes, and are subject to change without notice. Contents cover the three main categories of (i) Nuclear Measurements, Techniques and Instrumentation (Physics, Chemistry, Dosimetry Techniques, Nuclear Analytical Techniques, Research Reactors and Particle Accelerator Applications, Nuclear Data); (ii) Industrial Applications (Radiation Processing, Radiometry, Tracers); and (iii) Plasma Physics and Nuclear Fusion

  6. Nuclear measurements, techniques and instrumentation industrial applications plasma physics and nuclear fusion, 1980-1993. International Atomic Energy Agency publications

    International Nuclear Information System (INIS)

    1994-01-01

    This catalogue lists all sales publications of the International Atomic Energy Agency dealing with Nuclear Measurements, Techniques and Instrumentation, with Industrial Applications (of Nuclear Physics and Engineering), and with Plasma Physics and Nuclear Fusion, issued during the period 1980-1993. Most publications are in English. Proceedings of conferences, symposia, and panels of experts may contain some papers in other languages (French, Russian, or Spanish), but all papers have abstracts in English. Price quotes are in Austrian Schillings, do not include local taxes, and are subject to change without notice. Contents cover the three main categories of (I) Nuclear Measurements, Techniques and Instrumentation (Physics, Chemistry, Dosimetry Techniques, Nuclear Analytical Techniques, Research Reactors and Particle Accelerator Applications, Nuclear Data); (ii) Industrial Applications (Radiation Processing, Radiometry, Tracers); and (iii) Plasma Physics and Nuclear Fusion

  7. Industrialization

    African Journals Online (AJOL)

    Lucy

    . African states as ... regarded as the most important ingredients that went to add value to land and labour in order for countries ... B. Sutcliffe Industry and Underdevelopment (Massachusetts Addison – Wesley Publishing Company. 1971), pp.

  8. Industrialization

    African Journals Online (AJOL)

    Lucy

    scholar, Walt W. Rostow presented and supported this line of thought in his analysis of ... A Brief Historical Background of Industrialization in Africa ... indicative) The western model allowed for the political economy to be shaped by market.

  9. L’instabilité organisationnelle des districts industriels. Dynamiques des transformations internes d’un village de métier au nord du Viêt Nam The Organizational Instability of Industrial Districts: Dynamic Internal Transformations of a Craft Village in Northern Vietnam

    Directory of Open Access Journals (Sweden)

    Nguyen Quy Nghi

    2012-11-01

    Full Text Available Le village de métier est un sujet d’étude attractif, mais rarement traité comme une forme d’agglomération industrielle ou abordé sous l’angle de la sociologie industrielle. Le développement actuel des villages de métier montre bien la présence intensive des entreprises de tailles variées et l’implication d’autres acteurs en dehors du milieu de production (par exemple les autorités locales, le milieu de l’éducation. L’introduction d’acteurs nouveaux implique le changement des relations existantes, contribuant ainsi à la mise en place d’une nouvelle configuration. L’objectif de cet article est de montrer que l’organisation des villages de métier, qui est conçue comme un type de district industriel, est marquée par l’instabilité ou le changement permanent de la configuration générale, mais aussi par une transformation interne des acteurs au sein du district. À travers une étude de cas à Bát Tràng – un centre de production céramique au nord du Viêt Nam – cet article a pour objectif de montrer comment des entreprises familiales se réorganisent en structure plus formalisée, comment elles mobilisent du capital social pour régler leurs difficultés et les stratégies d’innovation qu’elles développent.Craft village is an attractive research subject, however it is rarely treated as a form of industrial agglomeration or studied from industrial sociology perspective. The current development of craft villages demonstrates the intensive presence of entreprises of all sizes and involvement of non productive actors (e.g. local authorities, education sector. The introduction of new actors therefore implies a change of existing relationships, contributing to the formulation of new configuration. The objective of this paper is to demonstrate that the organization of craft villages, as a type of industrial district, is marked by instability or permanent change in the overall configuration, but also by

  10. Industry

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

    2007-12-01

    This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of

  11. Modeling injury rates as a function of industrialized versus on-site construction techniques.

    Science.gov (United States)

    Rubio-Romero, J C; Suárez-Cebador, M; Abad, Jesús

    2014-05-01

    It is often predicted that the industrialization of building activities will lead to a reduction of accident rates in the construction sector, particularly as a result of switching activities from building sites to factories. However, to date no scientific research has provided objective quantitative results to back up this claim. The aim of this paper is to evaluate how industrialization affects the accident rate in different industrialized building systems in Spain. Our results revealed that the industrialized steel modular system presents the lowest accident rate, while the highest accident rate was recorded in the construction method with cast-in-place concrete. The lightweight construction system also presents a high accident rate. Accordingly, industrialized building systems cannot claim to be safer than traditional ones. The different types of "on-site work" seem to be the main variable which would explain the accident rates recorded in industrialized construction systems. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. "Zaï" Technique traditionnelle de restauration et de récupération des terres arides

    Directory of Open Access Journals (Sweden)

    Sonda, JM.

    1990-01-01

    Full Text Available "Zai", a traditional technique for restoring and recovering of arid soils. This work presents some observations about mountain gorillas behaviour in captivity at Tshibati. After their death, it is sad to see that their breeding is like sent back while many scientific informations are unknown on these primates.

  13. Applying industrial process improvement techniques to increase efficiency in a surgical practice.

    Science.gov (United States)

    Reznick, David; Niazov, Lora; Holizna, Eric; Siperstein, Allan

    2014-10-01

    The goal of this study was to examine how industrial process improvement techniques could help streamline the preoperative workup. Lean process improvement was used to streamline patient workup at an endocrine surgery service at a tertiary medical center utilizing multidisciplinary collaboration. The program consisted of several major changes in how patients are processed in the department. The goal was to shorten the wait time between initial call and consult visit and between consult and surgery. We enrolled 1,438 patients enrolled in the program. The wait time from the initial call until consult was reduced from 18.3 ± 0.7 to 15.4 ± 0.9 days. Wait time from consult until operation was reduced from 39.9 ± 1.5 to 33.9 ± 1.3 days for the overall practice and to 15.0 ± 4.8 days for low-risk patients. Patient cancellations were reduced from 27.9 ± 2.4% to 17.3 ± 2.5%. Overall patient flow increased from 30.9 ± 5.1 to 52.4 ± 5.8 consults per month (all P process improvement methodology, surgery patients can benefit from an improved, streamlined process with significant reduction in wait time from call to initial consult and initial consult to surgery, with reduced cancellations. This generalized process has resulted in increased practice throughput and efficiency and is applicable to any surgery practice. Copyright © 2014 Elsevier Inc. All rights reserved.

  14. NIR techniques create added values for the pellet and biofuel industry.

    Science.gov (United States)

    Lestander, Torbjörn A; Johnsson, Bo; Grothage, Morgan

    2009-02-01

    A 2(3)-factorial experiment was carried out in an industrial plant producing biofuel pellets with sawdust as feedstock. The aim was to use on-line near infrared (NIR) spectra from sawdust for real time predictions of moisture content, blends of sawdust and energy consumption of the pellet press. The factors varied were: drying temperature and wood powder dryness in binary blends of sawdust from Norway spruce and Scots pine. The main results were excellent NIR calibration models for on-line prediction of moisture content and binary blends of sawdust from the two species, but also for the novel finding that the consumption of electrical energy per unit pelletized biomass can be predicted by NIR reflectance spectra from sawdust entering the pellet press. This power consumption model, explaining 91.0% of the variation, indicated that NIR data contained information of the compression and friction properties of the biomass feedstock. The moisture content model was validated using a running NIR calibration model in the pellet plant. It is shown that the adjusted prediction error was 0.41% moisture content for grinded sawdust dried to ca. 6-12% moisture content. Further, although used drying temperatures influenced NIR spectra the models for drying temperature resulted in low prediction accuracy. The results show that on-line NIR can be used as an important tool in the monitoring and control of the pelletizing process and that the use of NIR technique in fuel pellet production has possibilities to better meet customer specifications, and therefore create added production values.

  15. Modeling injury rates as a function of industrialized versus on-site construction techniques

    OpenAIRE

    Rubio Romero, Juan Carlos; Suárez Cebador, Manuel; Abad Puente, Jesús

    2014-01-01

    It is often predicted that the industrialization of building activities will lead to a reduction of accident rates in the construction sector, particularly as a result of switching activities from building sites to factories. However, to date no scientific research has provided objective quantitative results to back up this claim. The aim of this paper is to evaluate how industrialization affects the accident rate in different industrialized building systems in Spain. Our results revealed tha...

  16. Recent technical progress in the French uranium industry; Les recents progres techniques dans l'industrie de l'uranium en France

    Energy Technology Data Exchange (ETDEWEB)

    Huet, H. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1961-07-01

    This paper reviews the present-day uranium production situation in France. The various stages of the treatment the concentrates receive, leading to the final production of the metal, are described briefly: dissolution, purification by extraction with a mixture of tributyl phosphate and white spirit, precipitation with ammonia, drying and calcination of the trioxide, reduction with hydrogen, cracked ammonia or preferably pure ammonia gas, fluorination with anhydrous hydrofluoric acid, and production of the metal by the calcium thermite process. Recent work of an original nature is discussed in greater detail. (author) [French] L'expose fait le point de la technique actuelle en ce qui concerne la fabrication de l'uranium en France. Il retrace brievement les diverses etapes du traitement des concentres pour aboutir au metal: mise en solution, purification par extraction au melange phosphate de tributylo-white spirit, precipitation par l'ammoniaque, sechage et calcination du trioxyde, reduction a l'hydrogene, a l'ammoniac craque ou mieux au gaz ammoniac pur, fluoruration par l'acide fluorhydrique anhydre et elaboration du metal par calciothermie. De plus amples details sont donnes sur les realisations recentes d'un caractere original. (auteur)

  17. Recent technical progress in the French uranium industry; Les recents progres techniques dans l'industrie de l'uranium en France

    Energy Technology Data Exchange (ETDEWEB)

    Huet, H [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1961-07-01

    This paper reviews the present-day uranium production situation in France. The various stages of the treatment the concentrates receive, leading to the final production of the metal, are described briefly: dissolution, purification by extraction with a mixture of tributyl phosphate and white spirit, precipitation with ammonia, drying and calcination of the trioxide, reduction with hydrogen, cracked ammonia or preferably pure ammonia gas, fluorination with anhydrous hydrofluoric acid, and production of the metal by the calcium thermite process. Recent work of an original nature is discussed in greater detail. (author) [French] L'expose fait le point de la technique actuelle en ce qui concerne la fabrication de l'uranium en France. Il retrace brievement les diverses etapes du traitement des concentres pour aboutir au metal: mise en solution, purification par extraction au melange phosphate de tributylo-white spirit, precipitation par l'ammoniaque, sechage et calcination du trioxyde, reduction a l'hydrogene, a l'ammoniac craque ou mieux au gaz ammoniac pur, fluoruration par l'acide fluorhydrique anhydre et elaboration du metal par calciothermie. De plus amples details sont donnes sur les realisations recentes d'un caractere original. (auteur)

  18. The formation of scientists and technicians at the 'Centre d'Etudes Nucleaires' at Saclay; Formation des scientifiques et des techniciens au Centre d'Etudes Nucleaires de Saclay

    Energy Technology Data Exchange (ETDEWEB)

    Debiesse, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    The considerable needs in research workers and scientists which are asked by the nuclear energy obliged the Commissariat a l'Energie atomique to deal with a particular effort to increase the quantitative and qualitative formation of scientists. Most various ways have been used. 1- A National Institute of Nuclear Sciences and Nuclear Techniques was created, by a joint decree of the Prime Minister and the Minister for National Education (june 18, 1957). This Institute of Higher Teaching (250 students) indulges in the following matters: atomic engineering, quantum mechanics, theory and technic of particle accelerators, special metallurgy, radiobiology, thermic and mechanics of fluids. 2- An associated centre of the 'Conservatoire National des Arts et Metiers' waeated (200 students) for technical assistants, drawers, etc. 3- In contribution with both electronic industry and Ministry of Work, the Centre d'Etudes Nucleaires contributes to an accelerated formation of technical assistants into Professional Centres. Conclusion: Training of scientists and research workers is one of the most important activities of the Centre d'Etudes Nucleaires de Saclay. Without losing its technical efficiency, it has supplied and varied means adapted to the various purposes that we shall reach. (author)Fren. [French] Les besoins considerables actuels et previsibles en chercheurs et scientifiques necessites par l'avevement de l'energie nucleaire imposaient au Commissariat a I'Energie atomique un effort particulier pour augmenter la formation quantitative et qualitative des scientifiques. Les moyens les plus divers ont ete mis en oeuvre: 1- Creation de l'Institut National des Sciences et Techniques Nucleaires par decret de la Presidence du Conseil et de l'Education Nationale en date du 18.6.57. Cet Institut d'Enseignement Superieur (250 etudiants) donne des cours en: genie atomique, mecanique quantique, theorie et technique des Accelerateurs de particules, metallurgie speciale, radiobiologie

  19. The sanitary approach: risk assessment according to the usable drainage techniques; L'approche sanitaire: evaluation des risques selon les techniques d'evacuation utilisables

    Energy Technology Data Exchange (ETDEWEB)

    Mouthon, G. [Ecole Nationale Veterinaire d' Alfort, 94 - Maison-Alfort (France)

    2003-02-01

    Sludges are by-products of waste water processing facilities. These sludges contain organic matter which can be valorized in agriculture, but they also contain microorganisms (parasites, bacteria, viruses, prions, dioxines), noxious compounds like heavy metals and persistent organic micro-pollutants. Valorization processes are developed to reduce the sanitary and environmental risks of sludges which are reviewed in this article: metal micro-pollutants (origin, physico-chemical state, transfer in the soil, accumulation in plants and soils, remobilization by erosion, French legislation about trace elements content); organic micro-pollutants (nature, public health risks, transfer in plants and environments, regulation); pathogenic microorganisms in sludges (content, abatement by spreading); valorization of urban and industrial sludges (disposal, spreading in agriculture, heavy metals elimination using Ondeo's 'Metix' process, incineration and valorization of combustion products); other valorization ways (biogas production, use as fuel for cement plants, phosphorous extraction). (J.S.)

  20. Dosimetric comparison of IMRT and modulated arc-therapy techniques in the treatment of cervical cancers; Comparaison dosimetrique des techniques de RCMI et d'arctherapie modulee dans le traitement des cancers du col uterin

    Energy Technology Data Exchange (ETDEWEB)

    Renard-Oldrini, S.; Charra-Brunaud, C.; Tournier-Rangeard, L.; Huger, S.; Marchesi, V.; Bouziz, D.; Peiffert, D. [Centre Alexis-Vautrin, Nancy (France)

    2011-10-15

    The authors report the dosimetric comparison of two techniques used for the treatment of cervical cancers: the intensity-modulated conformational radiotherapy (IMRT) with static beams and modulated arc-therapy with RapidArc. The treatment plans of 15 patients have been compared. The clinical target volume (CTV) comprises the gross target volume, the cervix, the upper third of the vagina, and ganglionary areas. The previsional target volume comprises the clinical target volume and a one centimetre margin. Organs at risk are rectum, bladder, intestine and bone marrow. Arc-therapy seems to provide a better sparing of intestine that IMRT, while maintaining a good coverage of the previsional target volume and decreasing treatment duration. Short communication

  1. The history of energy industry law in Germany. With particular emphasis on the development of the Energy Act (EnWG) and current proposals for reform under discussion; Zur Entwicklung des Energierechts in Deutschland. Unter besonderer Beruecksichtigung des Energiewirtschaftsgesetzes und der aktuellen Reformdiskussion

    Energy Technology Data Exchange (ETDEWEB)

    Smeddinck, U.

    1995-11-01

    The paper describes the history and development of the regulatory framework governing the energy industry and the reasons why this legislation has been creating an organisational framework of the power industry in Germany with some strikingly peculiar features. The core structure and the essential aspects of the Energy Act (EnWG) are discussed in detail, followed by a survey of relevant cartel laws and the regime of franchise agreements and franchise duties. The amendments made in response to the oil crisis in the early seventies are mentioned, and current trends and proposals for reform are outlined. The Annex contains material illustrating a number of significant developments and issues in the history of the energy industry law, with brief explanations. The bibliography also lists publications of interest to readers wishing to get more insight into ongoing debates about problems posed by energy industry law, and proposed reforms. [Deutsch] Der Beitrag zeichnet die Entstehung und Veraenderung des rechtlichen Ordnungsrahmens nach, der fuer die derzeitige eigentuemliche Organisation der deutschen Elektrizitaetswirtschaft verantwortlich ist. Im Mittelpunkt steht das EnWG mit seinem Grundmuster. Darueberhinaus werden die einschlaegigen kartellrechtlichen Vorschriften und das Konzessionsabgabenrecht vorgestellt. Weiter wird die Reaktion des Gesetzgebers auf die dramatische Oelkrise zu Beginn der siebziger Jahre deutlich. Schliesslich wird der gegenwaertige Stand der Novellierungsbemuehungen skizziert. Die im Anhang enthaltenen Materialien veranschaulichen einige markante Punkte der energierechtlichen Entwicklung. Sie sind jeweils mit einer kurzen Erlaeuterung versehen. Das Literaturverzeichnis enthaelt auch Veroeffentlichungen zur aktuellen Diskussion, die dem interessierten Leser den vertieften Einstieg in dieses Problemfeld moeglich machen.

  2. Photothermal and thermoelastic microscopies: two alternative techniques for the non-destructive testing of materials; Microscopies photothermiques et thermoelastiques: deux techniques alternatives pour le CND des materiaux

    Energy Technology Data Exchange (ETDEWEB)

    Fouaidy, M. [Institut de Physique Nucleaire, IN2P3/CNRS 91 - Orsay (France); Ridouane, H. [Faculte des Sciences Ben M' sik, LPPPC, Casablanca (Morocco)

    2002-07-01

    This work aims at evaluating the possibility of application of photothermal and thermoelastic microscopies to the non-destructive testing of materials, such as niobium used in the fabrication of superconductive RF cavities. The theoretical results obtained in this study show the diagnostic potentialities of these techniques when applied to niobium sheets or directly to cavities. The microscopes that use an intensity modulated laser as excitation source have a lateral resolution comprised between 1 {mu}m for f{sub mod} = 10 MHz and 30 to 50 {mu}m for f{sub mod} = 10 kHz with a 1 {mu}m diameter beam. These techniques allow the detection, localization, and sometimes the characterization, of subsurface and deep defects and inclusions. In far field regime the resolution of the method depends on the thermal diffusion depth. Thanks to the strong dependence between the laser induced stress and the thickness of the target, the photothermal and thermoelastic microscopes can be used also for the measurement of cavities thickness and internal profile. (J.S.)

  3. Combustion gas cleaning in the ceramic tile industry: technical guide; Nettoyage des fumees de combustion dans l'industrie ceramique: guide technique

    Energy Technology Data Exchange (ETDEWEB)

    Lezaun, F.J. [ENAGAS-Grupo Gas Natural (Spain); Mallol, G.; Monfort, E. [instituto de Tecnologia Ceramica, ITC (Spain); Busani, G. [Agenzia Regionale per la Prevenzione e l' Amiente, ARPA (Spain)

    2000-07-01

    This document presents a summary of a technical guide drawn up on combustion gas cleaning systems in ceramic frit and tile production. The guide describes the method to be followed for selecting the best possible solutions for reducing pollutant concentrations in different emission sources, in accordance with current regulatory requirements and the CET recommendation. There are three sources of combustion gas air emissions that need to be cleaned in ceramic tile and frit production and they are usually related to the following process stages: slip spray drying, tile firing and frit melting. The different nature of the emissions means that different substances will need to be cleaned in each emission. Thus, in spray drying and frit melting, the only species to be cleaned are suspended particles, while in tile firing, it is also necessary to reduce the fluorine concentration. The systems analysed in this guide are mainly wet cleaning systems, bag filters and electrostatic precipitators. In the study, the efficiency of these cleaning systems is compared at each emission source from a technical and economic point of view, and concrete solutions are put forward in each case, together with a list of suppliers of the technologies involved. (authors)

  4. removal of hazardous pollutants from industrial waste solutions using membrane techniques

    International Nuclear Information System (INIS)

    Selim, Y.T.M.

    2001-01-01

    the removal of hazardous pollutants from industrial waste solutions is of essential demand field for both scientific and industrial work. the present work includes detailed studies on the possible use of membrane technology especially liquid emulsion membrane for the removal of hazardous pollutants such as; cadmium , cobalt , lead, copper and uranium from different industrial waste solution . this research can be applied for mixed waste problems. the work carried out in this thesis is presented in three main chapters, namely introduction, experimental and results and discussion

  5. Genèse du nouveau master « Histoire des sciences et techniques, humanités numériques et médiations culturelles » : de l'articulation entre la recherche et la formation au Centre François Viète de l'Université de Bretagne Occidentale

    Directory of Open Access Journals (Sweden)

    Chambon Gregory

    2014-01-01

    Full Text Available L'objet de cet article est de montrer comment la dynamique de création simultanée, à Brest et depuis 2008, d'une nouvelle équipe de recherche et d'un nouveau master recherche à distance en 2012 s'est traduit par une proposition originale de formation par la recherche. Nous détaillons les spécificités de cette dernière. D'une part, elle prend fortement appui sur des axes de recherches et des nouvelles méthodologies en histoire des sciences et des techniques, qui s'inspirent des travaux sur la culture matérielle et la compréhension des systèmes complexes. En outre, nous montrons que des questions de recherche et de formation y sont intégrées concernant le développement ou l'usage des outils numériques (web sémantique, réalité virtuelle ou augmentée, etc. pour la recherche en SHS et médiations culturelles. L'équipe de Brest s'inscrit de ce fait dans le champ des travaux de recherches en humanités numériques en très forte collaboration avec notamment des laboratoires d'informatique. Au travers des thématiques traitées, des méthodologies enseignées, d'une pédagogie universitaire basée sur une classe virtuelle ainsi que de la nature des différents partenaires qui y enseignent, nous montrons ainsi que le master en question constituent un laboratoire où il est possible d'expérimenter de nouvelles pratiques de formation par la recherche.

  6. DEVELOPMENT OF A VIRTUAL INTELLIGENCE TECHNIQUE FOR THE UPSTREAM OIL INDUSTRY

    Energy Technology Data Exchange (ETDEWEB)

    Iraj A. Salehi; Shahab D. Mohaghegh; Samuel Ameri

    2004-09-01

    The objective of the research and development work reported in this document was to develop a Virtual Intelligence Technique for optimization of the Preferred Upstream Management Practices (PUMP) for the upstream oil industry. The work included the development of a software tool for identification and optimization of the most influential parameters in upstream common practices as well as geological, geophysical and reservoir engineering studies. The work was performed in cooperation with three independent producing companies--Newfield Exploration, Chesapeake Energy, and Triad Energy--operating in the Golden Trend, Oklahoma. In order to protect data confidentiality, these companies are referred to as Company One, Two, Three in a randomly selected order. These producing companies provided geological, completion, and production data on 320 wells and participated in frequent technical discussions throughout the project. Research and development work was performed by Gas Technology Institute (GTI), West Virginia University (WVU), and Intelligent Solutions Inc. (ISI). Oklahoma Independent Petroleum Association (OIPA) participated in technology transfer and data acquisition efforts. Deliverables from the project are the present final report and a user-friendly software package (Appendix D) with two distinct functions: a characterization tool that identifies the most influential parameters in the upstream operations, and an optimization tool that seeks optimization by varying a number of influential parameters and investigating the coupled effects of these variations. The electronic version of this report is also included in Appendix D. The Golden Trend data were used for the first cut optimization of completion procedures. In the subsequent step, results from soft computing runs were used as the guide for detailed geophysical and reservoir engineering studies that characterize the cause-and-effect relationships between various parameters. The general workflow and the main

  7. The influence of the PDMS technique in the study of the induced modifications of polymers used in nuclear environment; Apport de la technique PDMS a l`etude des modifications induites dans des polymeres utilises en ambiance nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Nsouli, B [Lyon-1 Univ., 69 - Villeurbanne (France). Inst. de Physique Nucleaire

    1995-07-20

    The PDMS technique (Particle Induced Desorption Mass Spectrometry) combined with a TOF detection (Time of Flight) is the main tool used in this study of polymer degradation in nuclear environment. Ar{sup 3+} ions with a 9 MeV energy have been used to induce the secondary ion emission, and the study was devoted to two stresses typical of this type of environment. The first part of the work concerned with the structural modifications induced by gamma irradiation on ion exchange resin, used for nuclear effluents reprocessing, namely the poly(4-vinylpyridine), or P-4PV. For such a material, the negative fragment emission is particularly sensitive to structural modifications. Difficult physical measurements in such an insoluble and infusible material (IR, UV - Vis, EPR, TGA, dielectric measurements) became consistent after the degradation mechanisms were elucidated. These effects, interpreted in terms of scissions and recombinations, enabled us to explicit different modes of energy deposition, and shed light on some discrepancies between SIMS and PDMS. The second part of the study is devoted to the thermal ageing of an elastomer, used in fabrication of valve gaskets submitted to high temperatures. First of all, we studied the constituents of the polymeric material, i. e. copolymer, homo polymers, and also additives. This last component proved useful to analyze, as a superficial lubricant layer can mask the conformational rearrangements which seem to occur after few hours of thermal treatment (PE blocks are prevailing at the surface). Here too, the PDMS information is important to account for static SIMS and ESCA results, as its probed layer thickness lies in-between. (author) 187 refs.

  8. Quality comparison between DEF-10 digital image from simulation technique and Computed Tomography (CR) technique in industrial radiography

    International Nuclear Information System (INIS)

    Siti Nur Syatirah Ismail

    2012-01-01

    The study was conducted to make comparison of digital image quality of DEF-10 from the techniques of simulation and computed radiography (CR). The sample used is steel DEF-10 with thickness of 15.28 mm. In this study, the sample is exposed to radiation from X-ray machine (ISOVOLT Titan E) with certain parameters. The parameters used in this study such as current, volt, exposure time and distance are specified. The current and distance of 3 mA and 700 mm respectively are specified while the applied voltage varies at 140, 160, 180 and 200 kV. The exposure time is reduced at a rate of 0, 20, 40, 60 and 80 % for each sample exposure. Digital image of simulation produced from aRTist software whereas digital image of computed radiography produced from imaging plate. Therefore, both images were compared qualitatively (sensitivity) and quantitatively (Signal to-Noise Ratio; SNR, Basic Spatial Resolution; SRb and LOP size) using Isee software. Radiographic sensitivity is indicated by Image Quality Indicator (IQI) which is the ability of the CR system and aRTist software to identify IQI of wire type when the time exposure is reduced up to 80% according to exposure chart ( D7; ISOVOLT Titan E). The image of the thinnest wire diameter achieved by radiograph from simulation and CR are the wire numbered 7 rather than the wire numbered 8 required by the standard. In quantitative comparison, this study shows that the SNR values decreases with reducing exposure time. SRb values increases for simulation and decreases for CR when the exposure time decreases and the good image quality can be achieved at 80% reduced exposure time. The high SNR and SRb values produced good image quality in CR and simulation techniques respectively. (author)

  9. Simulation of sustainability aspects within the industrial environment and their implication on the simulation technique

    OpenAIRE

    Rabe, M.; Jäkel, F.-W.; Weinaug, H.

    2010-01-01

    Simulation is a broadly excepted analytic instrument and planning tool. Today, industrial simulation is mainly applied for engineering and physical purposes and covers a short time horizon compared to intergenerational justice. In parallel, sustainability is gaining more importance for the industrial planning because themes like global warming, child labour, and compliance with social and environmental standards have to be taken into account. Sustainability is characterized by comprehensively...

  10. Development of a genome editing technique using the CRISPR/Cas9 system in the industrial filamentous fungus Aspergillus oryzae.

    Science.gov (United States)

    Katayama, Takuya; Tanaka, Yuki; Okabe, Tomoya; Nakamura, Hidetoshi; Fujii, Wataru; Kitamoto, Katsuhiko; Maruyama, Jun-Ichi

    2016-04-01

    To develop a genome editing method using the CRISPR/Cas9 system in Aspergillus oryzae, the industrial filamentous fungus used in Japanese traditional fermentation and for the production of enzymes and heterologous proteins. To develop the CRISPR/Cas9 system as a genome editing technique for A. oryzae, we constructed plasmids expressing the gene encoding Cas9 nuclease and single guide RNAs for the mutagenesis of target genes. We introduced these into an A. oryzae strain and obtained transformants containing mutations within each target gene that exhibited expected phenotypes. The mutational rates ranged from 10 to 20 %, and 1 bp deletions or insertions were the most commonly induced mutations. We developed a functional and versatile genome editing method using the CRISPR/Cas9 system in A. oryzae. This technique will contribute to the use of efficient targeted mutagenesis in many A. oryzae industrial strains.

  11. Administration et gestion des contrats XL

    CERN Document Server

    Senouf, J

    2000-01-01

    Les grands contrats de travaux génèrent un grand nombre de commandes (OSVC) passées par un grand nombre de responsables techniques. Ils sont généralement basés sur des bordereaux de prix associés à un éventail de conditions économiques adaptées aux besoins complexes et variés des multiples utilisateurs du CERN nécessitant des calculs sophistiqués. L'administration des commandes, le suivi des travaux et de la facturation doivent répondre aux besoins de tous les acteurs. Les responsables techniques doivent jouir de la plus large indépendance administrative dans le respect des règlements CERN et des conditions contractuelles. Le contrôle des métrés et décomptes doit être rigoureux et d'une traçabilité complète. L'utilisation des bases de données Oracle a déjà permis l'intégration des données administratives et techniques. Le Web nous invite à une communication totale et transparente entre les utilisateurs, les services techniques et les contractants. De nouveaux types de contrat so...

  12. Problem-solving and developing quality management methods and techniques on the example of automotive industry

    OpenAIRE

    Jacek Łuczak; Radoslaw Wolniak

    2015-01-01

    The knowledge about methods and techniques of quality management together with their effective use can be definitely regarded as an indication of high organisational culture. Using such methods and techniques in an effective way can be attributed to certain level of maturity, as far as the quality management system in an organisation is concerned. There is in the paper an analysis of problem-solving methods and techniques of quality management in the automotive sector in Poland. The survey wa...

  13. Current Techniques of Growing Algae Using Flue Gas from Exhaust Gas Industry: a Review.

    Science.gov (United States)

    Huang, Guanhua; Chen, Feng; Kuang, Yali; He, Huan; Qin, An

    2016-03-01

    The soaring increase of flue gas emission had caused global warming, environmental pollution as well as climate change. Widespread concern on reduction of flue gas released from industrial plants had considered the microalgae as excellent biological materials for recycling the carbon dioxide directly emitted from exhaust industries. Microalgae also have the potential to be the valuable feedback for renewable energy production due to their high growth rate and abilities to sequester inorganic carbon through photosynthetic process. In this review article, we will illustrate important relative mechanisms in the metabolic processes of biofixation by microalgae and their recent experimental researches and advances of sequestration of carbon dioxide by microalgae on actual industrial and stimulate flue gases, novel photobioreactor cultivation systems as well as the perspectives and limitations of microalgal cultivation in further development.

  14. Applying data mining techniques to explore factors contributing to occupational injuries in Taiwan's construction industry.

    Science.gov (United States)

    Cheng, Ching-Wu; Leu, Sou-Sen; Cheng, Ying-Mei; Wu, Tsung-Chih; Lin, Chen-Chung

    2012-09-01

    Construction accident research involves the systematic sorting, classification, and encoding of comprehensive databases of injuries and fatalities. The present study explores the causes and distribution of occupational accidents in the Taiwan construction industry by analyzing such a database using the data mining method known as classification and regression tree (CART). Utilizing a database of 1542 accident cases during the period 2000-2009, the study seeks to establish potential cause-and-effect relationships regarding serious occupational accidents in the industry. The results of this study show that the occurrence rules for falls and collapses in both public and private project construction industries serve as key factors to predict the occurrence of occupational injuries. The results of the study provide a framework for improving the safety practices and training programs that are essential to protecting construction workers from occasional or unexpected accidents. Copyright © 2011 Elsevier Ltd. All rights reserved.

  15. A Study on an Executive Technique and Activation of Clean Production in Chemical Industry

    Energy Technology Data Exchange (ETDEWEB)

    Kong, Seong Yong; Lee, Hee Seok; Kim, Kang Seok [Korea Environment Institute, Seoul (Korea)

    2000-12-01

    Clean production does not only make the sustainable development possible through preventing the deterioration of the environmental pollution from the expansion of industrialization but also enhance the company's competitiveness. Clean production is required by all industrial fields but is the most important in chemical industry. The Government has made efforts to change the domestic industrial structure to the environmental-friendly structure through developing the research. However, the domestic industry has not yet activated overall except some large companies, which has concretized the activation of clean production. Especially, the medium and small companies are more sluggish due to the inferiority of capital and technology. With recognizing that the main body of clean production is a company, the effort based on the Government and the academic world, without companies' positive, will cannot help being limited in effects. Therefore, it is necessary to trigger the schemes that urge the companies' motivation to show the effects from the support that have concentrated in hardware like technology until now. It seems to be very important that the guidebook for clean production, which a company can easily adopt, is developed and spread. This report provides the guidebook for clean production that managers and engineers can easily understand and approach in a producing field and presents the scheme to promote clean production, for chemical industry that is seriously required clean production. Even if the presented contents are not perfect, they can be applied to the development of the Government's policy and the administrative activities of companies for clean production as a useful data. 53 refs., 5 figs., 30 tabs.

  16. Speciation and evolution of cyanide compounds contained in industrial residues from coal pyrolysis; Speciation et evolution des composes cyanures contenus dans des residus industriels issus de la pyrolyse de la houille

    Energy Technology Data Exchange (ETDEWEB)

    Proffit, D.

    2002-10-15

    Occurrence of cyanide compounds, mainly [Fe(CN)6]2-/3-, in soils and groundwater is due to industrial waste deposits. The main polluting source are purifier wastes stored on former manufactured gas plant sites. In order to estimate the environmental risks associated with cyanide, a specific analytical procedure combining analyses on the solids (optical and scanning electron microscopies, infrared spectroscopy and x-ray diffraction) with analyses carried out on leachates obtained by aqueous extraction at various pHs was developed. For a given purifier waste, Prussian blue was evidenced as the major cyanide species but other minor compounds were also observed. Some of them are extremely soluble (e.g. potassium ferrocyanide) whereas others are very stable (e.g. potassium and zinc ferrocyanide). The study of other polluted solids allowed to predict the hazards linked with their storage. Measurements realized on percolation columns effluents revealed that cyanide species can migrate as colloidal species as well as under soluble forms, which confirmed some site observations where cyanide pollution was observed in soils located beneath a priori stable wastes. Such a combination of techniques can then be considered as a useful diagnosis and risk assessment tool. However, as the full procedure is rather time-consuming a partial combination of the techniques developed can even be used advantageously in some specific cases. We also developed a quantification and speciation method (spectrometric UV-Visible - mathematical code) to determine cyanide compounds concentrations in water extraction filtrates. Finally, irradiation tests of purifier wastes were carried out. They revealed that the influence of natural light could be considered as negligible in comparison to the other factors affecting cyanide compounds migration.

  17. The energy sector between the two poles of the free market system and the public service obligations. Potential and limitations of state control, with an emphasis on the act for reform of the energy industry law (ENG) and the EU Internal Market Directive; Der Energiesektor zwischen Marktwirtschaft und oeffentlicher Aufgabe. Moeglichkeiten und Grenzen staatlicher Steuerung unter besonderer Beruecksichtigung des Gesetzes zur Neuregelung des Energiewirtschaftsrechts und des Europarechts

    Energy Technology Data Exchange (ETDEWEB)

    Hoelzer, F.

    2000-07-01

    In Part A of the book it will be brought out that despite differing conceptual starting points and despite state control's way of working, there is no alternative to legal control. In co-operative models and consensual solutions in those states with private sector service providers, which exist in diverse forms in the energy sector, too, the law operates as a framework or regulatory warning, or it has a reserve function. An end to state control is not linked to that because the state remains responsible for the achievement of the goals the notification ans definition of which it undertakes as a public duty. The results found are discussed and confirmed in Part B of the book in connection with the reform of the legal framework of the energy industry (the German act named ENG). In Part C of the book it will be shown to what extent legal constitutional limitations stand in the way of state control in the energy sector. (orig./CB) [German] Im ersten Teil der Arbeit wird staatliche Steuerung durch Recht an Beispielen des Energiesektors untersucht, wobei insbesondere Fragen des Wirkens und der Erscheinungsformen staatlicher Steuerung sowie die Auswirkungen der Veraenderung staatlicher Steuerung auf die Rolle des Staates und auf das Verhaeltnis von Staat und Gesellschaft im Vordergrund stehen. Im zweiten Teil werden unter besonderer Beruecksichtigung der europarechtlichen Regelungen die Moeglichkeiten, rechtliche Grenzen und Maengel staatlicher Steuerung im bisherigen System der Elektrizitaetsversorgung in Deutschland dargestellt, da Reformen, um dem Steuerungsanspruch des Staates gerecht zu werden, diesezu beachten haben. Es wird u.a. untersucht, inwieweit Entstaatlichungsstrategien im Rahmen der Reformen im Energiesektor Anwendung finden. Im dritten Teil werden die verfassungsrechtlichen Restriktionen untersucht. (orig./CB)

  18. Technique of calculating the total effectiveness of capital investments and basic funds in the gas industry

    Energy Technology Data Exchange (ETDEWEB)

    Shamis, L V

    1978-01-01

    An examination is made of the method of calculating and using the indicators for total effectiveness of capital investments of the gas industry. Fundamentals of the calculations assume modeling the effectiveness of reproduction of the basic production funds of the sector. An example is given of calculating the long-term coefficient for total effectiveness.

  19. Novel GIMS technique for deposition of colored Ti/TiO₂ coatings on industrial scale

    Directory of Open Access Journals (Sweden)

    Zdunek Krzysztof

    2016-03-01

    Full Text Available The aim of the present paper has been to verify the effectiveness and usefulness of a novel deposition process named GIMS (Gas Injection Magnetron Sputtering used for the flrst time for deposition of Ti/TiO₂ coatings on large area glass Substrates covered in the condition of industrial scale production. The Ti/TiO₂ coatings were deposited in an industrial System utilizing a set of linear magnetrons with the length of 2400 mm each for covering the 2000 × 3000 mm glasses. Taking into account the speciflc course of the GIMS (multipoint gas injection along the magnetron length and the scale of the industrial facility, the optical coating uniformity was the most important goal to check. The experiments on Ti/TiO₂ coatings deposited by the use of GIMS were conducted on Substrates in the form of glass plates located at the key points along the magnetrons and intentionally non-heated during any stage of the process. Measurements of the coatings properties showed that the thickness and optical uniformity of the 150 nm thick coatings deposited by GIMS in the industrial facility (the thickness differences on the large plates with 2000 mm width did not exceed 20 nm is fully acceptable form the point of view of expected applications e.g. for architectural glazing.

  20. Industrial implementation of plasma deposition using the expanding thermal plasma technique

    NARCIS (Netherlands)

    Sanden, van de M.C.M.; Oever, van den P.J.; Creatore, M.; Schaepkens, M.; Miebach, T.; Iacovangelo, C.D.; Bosch, R.C.M.; Bijker, M.D.; Evers, M.F.J.; Schram, D.C.; Kessels, W.M.M.

    2004-01-01

    Two successful industrial implementations of the expanding thermal plasma setup, a novel plasma source, obtaining high deposition rate are discussed. The Ar/O2/hexamethyldisiloxane and Ar/O2/octamethyl-cyclosiloxane-fed expanding thermal plasma setup is used to deposit scratch resistant silicone

  1. Assessment of postur in an automotive industry using ISO -11228-3 technique

    Directory of Open Access Journals (Sweden)

    2012-01-01

    Results: Results shown in 4 workstations include 35 task in an automotive industry. One of them is red and another’s are green.. Conclusion: This method is suitable, quickly and very easy to use for assessment of ergonomics situation in work.

  2. Technical and economic assessments of storage techniques for long-term retention of industrial-beet sugar for non-food industrial fermentations

    Science.gov (United States)

    Vargas-Ramirez, Juan Manuel

    Industrial beets may compete against corn grain as an important source of sugars for non-food industrial fermentations. However, dependable and energy-efficient systems for beet sugar storage and processing are necessary to help establish industrial beets as a viable sugar feedstock. Therefore, technical and economic aspects of beet sugar storage and processing were evaluated. First, sugar retention was evaluated in whole beets treated externally with either one of two antimicrobials or a senescence inhibitor and stored for 36 wk at different temperature and atmosphere combinations. Although surface treatment did not improve sugar retention, full retention was enabled by beet dehydration caused by ambient air at 25 °C and with a relative humidity of 37%. This insight led to the evaluation of sugar retention in ground-beet tissue ensiled for 8 wk at different combinations of acidic pH, moisture content (MC), and sugar:solids. Some combinations of pH ≤ 4.0 and MC ≤ 67.5% enabled retentions of at least 90%. Yeast fermentability was also evaluated in non-purified beet juice acidified to enable long-term storage and partially neutralized before fermentation. None of the salts synthesized through juice acidification and partial neutralization inhibited yeast fermentation at the levels evaluated in that work. Conversely, yeast fermentation rates significantly improved in the presence of ammonium salts, which appeared to compensate for nitrogen deficiencies. Capital and operating costs for production and storage of concentrated beet juice for an ethanol plant with a production capacity of 76 x 106 L y-1 were estimated on a dry-sugar basis as U.S. ¢34.0 kg-1 and ¢2.2 kg-1, respectively. Storage and processing techniques evaluated thus far prove that industrial beets are a technically-feasible sugar feedstock for ethanol production.

  3. Caractérisation de formations Miocène de la région de Taza pour des valorisations et exploitations industrielles Industrial value of the Miocene calcarenites in the region of Taza

    Directory of Open Access Journals (Sweden)

    Lahrach A.

    2012-09-01

    Full Text Available La valorisation de la formation Miocène dans la région de Taza, représentée par les calcarénites, a été menée selon deux axes ; tout d’abord une étude géologique, couplée à des études de terrain nous a permis d’évaluer l’épaisseur de la formation, une carte d’épaisseur a été dressée à cet effet. L’étude géotechnique de ces matériaux révèle que ces calcarénites ont des qualités intéressantes pour des utilisations industrielles. En effet, en se basant sur les différents tests de dureté (Los Angeles et Micro Duval, la résistance à la rupture et la porosité de nos quatre échantillons, une valeur ajoutée industrielle peut leur être attribuée dans beaucoup de domaines, comme: -Graves non traités pour couches de fondations pour les chaussées ou grave bitumeux de fondation; -Ajouts dans les bétons; -Roche marbrière et pierre de façade. En fin, sur la base de ces études géologiques et géotechniques, on peut considérer que les calcarénites de la région de Taza répondent à l’ensemble des critères d’une exploitation industrielle. The valuation of the Miocene formation in the Taza region, represented by calcarenites, was conducted according two axes; first geological survey, coupled with field studies allowed us to evaluate the thickness of the formation, a thickness map was derived from this purpose. The geotechnical study of these materials reveals that these calcarenites have interesting qualities for industrial uses. Indeed, based on the different hardness tests (Los Angeles and Micro Duval, the tensile strength and porosity of our four samples, an industrial added value can be attributed to them in many areas, such as: - Untreated Graves for layers of foundations for pavements or bituminous serious foundation; - Additions in concrete; - Roche marble and stone facade. Finally, on the basis of geological and geotechnical studies, we can consider that the calcarenites of the Taza region meet

  4. Evaluation des pratiques de gestion des adventices en riziculture ...

    African Journals Online (AJOL)

    Le riz est l'aliment principal pour la quasi-totalité des populations vivant en Côte d'Ivoire. Cependant, les adventices sont considérées comme la contrainte biologique la plus importante faisant obstacle à la production rizicole. L'objectif de cette étude menée en 2015 était d'évaluer différentes techniques de gestion des ...

  5. Rapport final de la Collaboration CERN-CNRS pour la construction du LHC Accord Technique d'Exécution No 2 Cryostats et assemblage des sections droites courtes (SSS) du LHC

    CERN Document Server

    Bergot, JB; Poncet, A; Rohmig, P; Roy, E; Vincent, D

    2006-01-01

    Depuis 1995 et suite à la signature du protocole de Collaboration, le CERN, le CEA et le CNRS ont étroitement collaboré dans le cadre de la contribution exceptionnelle de la France à la construction du LHC. Pour le CNRS, l'Institut de Physique Nucléaire d'Orsay a pris en charge deux Accords Techniques d'Exécution. Le premier concerne la conception et l'assemblage des Sections Droites Courtes de la machine, et le deuxième, l'étalonnage des thermomètres cryogéniques du LHC. Dans le cadre de l'Accord Technique d'Exécution N°2, le Bureau d'Etudes de la Division Accélérateur de l'IPNO et le groupe AT-CRI du CERN ont travaillé de concert pour mener à bien la conception des SSS (Short Straight Section) et de tous les équipements nécessaires à l'assemblage. Ce rapport a donc pour objectif de dresser, en termes d'historique, d'organisation, de résultats quantitatifs et qualitatifs et de moyens mis en ?uvre, un tableau aussi complet que possible du déroulement de cette Collaboration entre le CERN e...

  6. Analysis of visual representation techniques for product configuration systems in industrial companies

    DEFF Research Database (Denmark)

    Shafiee, Sara; Kristjansdottir, Katrin; Hvam, Lars

    2016-01-01

    with knowledge representations and communications with domain experts. The results presented in the paper are therefore aimed to provide insight into the impact from using visual knowledge representations techniques in PCSs projects. The findings indicate that use of visual knowledge representations techniques...... in PCSs projects will result in improved quality of maintenance and development support for the knowledge base and improved quality of the communication with domain experts....

  7. Sampling phased array, a new technique for ultrasonic signal processing and imaging now available to industry

    OpenAIRE

    Verkooijen, J.; Bulavinov, A.

    2008-01-01

    Over the past 10 years the improvement in the field of microelectronics and computer engineering has led to significant advances in ultrasonic signal processing and image construction techniques that are currently being applied to non-destructive material evaluation. A new phased array technique, called "Sampling Phased Array" has been developed in the Fraunhofer Institute for non-destructive testing [1]. It realizes a unique approach of measurement and processing of ultrasonic signals. The s...

  8. Possibilities of radiation technique application in machine-building industry of Bulgaria

    International Nuclear Information System (INIS)

    Petrov, A.; Avramov, D.; Kostov, St.

    1979-01-01

    In last ten years, in development of machine-building industry, tendency has been outlined for creation of machines and constructions having minimum weight and elevated reliability from one side due to improvement of design and technology of production and from the other side due to application of materials with improved parameters. Solution of these problems is closely connected with application of the radiation methods. State-of-art of the radiation technology application in the machine-building industry is analyzed and mainly for investigation of wear resistance of friction machineparts. Use of spatial radioactive labelling in investigation of materials and application of radiation methods for optimization of technological processes in metallurgy, foundry and so on is considered. Estimation is give of perspectives of further growth of introduction of radiation methods in Bulgaria [ru

  9. Study and industrial applications of the external slowing-down {beta}{sup -} radiation of the yttrium - 90; Etude et applications industrielles du rayonnement de freinage externe des {beta}{sup -} de l'yttrium - 90

    Energy Technology Data Exchange (ETDEWEB)

    Leveque, P; Martinelli, P; Chauvin, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    Inelastic scattering of the {beta}{sup -} particles on the nucleus gives place to the emission of a X-ray Bremsstrahlung radiation. In view of possible industrial applications, we studied the slowing-down radiation of {sup 90}(Sr + Y) sources in various materials. This pure {beta}{sup -} emitter of long period is in the fission products of uranium. Among of the industrial applications, these sources of weak X-rays energy can be used for the radiography of thin pieces, for measuring the thickness, or for the analysis by fluorescence. (M.B.) [French] La diffusion inelastique des particules {beta}{sup -} sur les noyaux donne lieu a l'emission d'un rayonnement X de freinage. En vue de possibles applications industrielles, nous avons etudie le rayonnement de freinage des sources {sup 90}(Sr + Y) dans divers materiaux. Cet emetteur {beta}{sup -} pur a longue periode se trouve dans les produits de fission de l'uranium. Parmi les applications industrielles a l'etude, ces sources de rayons X de faible energie peuvent etre utilisees pour la radiographie de pieces minces, la mesure d'epaisseurs, ou encore pour l'analyse par fluorescence. (M.B.)

  10. Benchmarking the scientific output of industrial wastewater research in Arab world by utilizing bibliometric techniques.

    Science.gov (United States)

    Zyoud, Shaher H; Al-Rawajfeh, Aiman E; Shaheen, Hafez Q; Fuchs-Hanusch, Daniela

    2016-05-01

    Rapid population growth, worsening of the climate, and severity of freshwater scarcity are global challenges. In Arab world countries, where water resources are becoming increasingly scarce, the recycling of industrial wastewater could improve the efficiency of freshwater use. The benchmarking of scientific output of industrial wastewater research in the Arab world is an initiative that could support in shaping up and improving future research activities. This study assesses the scientific output of industrial wastewater research in the Arab world. A total of 2032 documents related to industrial wastewater were retrieved from 152 journals indexed in the Scopus databases; this represents 3.6 % of the global research output. The h-index of the retrieved documents was 70. The total number of citations, at the time of data analysis, was 34,296 with an average citation of 16.88 per document. Egypt, with a total publications of 655 (32.2 %), was ranked the first among the Arab countries followed by Saudi Arabia 300 (14.7 %) and Tunisia 297 (14.6 %). Egypt also had the highest h-index, assumed with Saudi Arabia, the first place in collaboration with other countries. Seven hundred fifteen (35.2 %) documents with 66 countries in Arab/non-Arab country collaborations were identified. Arab researchers collaborated mostly with researchers from France 239 (11.7 %), followed by the USA 127 (6.2 %). The top active journal was Desalination 126 (6.2 %), and the most productive institution was the National Research Center, Egypt 169 (8.3 %), followed by the King Abdul-Aziz University, Saudi Arabia 75 (3.7 %). Environmental Science was the most prevalent field of interest 930 (45.8 %). Despite the promising indicators, there is a need to close the gap in research between the Arab world and the other nations. Optimizing the investments and developing regional experiences are key factors to promote the scientific research.

  11. Current market of industrial bio-products and biofuels, and predictable evolutions by 2015/2030. Synthesis; Marche actuel des bioproduits industriels et des biocarburants et evolutions previsibles a echeance 2015 / 2030. Synthese

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-04-15

    The main objectives of this study were to describe the current status of the energetic and industrial bio-product markets (biofuels, bio-lubricants, biomaterials, papers, cosmetics, and so on), to identify and analyze the evolution perspectives of these new markets on a long and medium term, to define scenarios of evolution for different sectors (agro-industry, energy, organic chemistry), to identify the most promising new markets, and to select the priority agro-industrial sectors

  12. Les schémas de sélection ovins laitiers en France : utilisation et importance des techniques modernes de reproduction

    OpenAIRE

    Astruc, J.M.; Lagriffoul, G.; Belloc, J.P.; Briois, M.; Cachenaut, J.B.; Horent, M.H.; Teinturier, M.H.

    1995-01-01

    La mise en oeuvre de programmes de sélection laitière, à l’échelle de toute une population ovine, suppose de développer un travail de sélection entre éleveurs, fondé sur l’organisation et la valorisation de liens génétiques entre troupeaux, essentiellement grâce à l’utilisation de l’IA. La situation en France est à cet égard révélatrice des différents niveaux d’organisation des schémas de sélection.

  13. Application of tracer techniques to industrial troubleshooting and environmental pollution control

    International Nuclear Information System (INIS)

    Easey, J.F.

    1994-01-01

    The field applications of tracer technology are reviewed and three specific examples each are given for use of the technology for industrial troubleshooting and for environmental pollution control. Each example examines the background, the experimental details and the result, particularly with regard to the cost benefits. Specific areas covered are: leak studies in a chemical reactor; wear studies in jet aircraft fuel pump, mass balance studies in gold refining; ocean dispersion of iron rich wastes; pollution discharges of mine waste water; and flow patterns and retention times in waste waster treatment lagoons. (author). 18 refs

  14. Analysis of nickel industrial wastes by nuclear techniques and its pollution assessment

    International Nuclear Information System (INIS)

    Diaz Rizo, O.; Coto Hernandez, I.; Lopez Pino, N.; D'Alessandro Rodriguez, K.; Arado Lopez, J.O.; Diaz Arado, O.; Reyes Perez, H.

    2011-01-01

    The concentration of some heavy metal (Mn, Fe, Co, Ni, Cu and Zn) in nickel industrial wastes from Moa, northeastern Cuba, is determined. The analysis was performed by External Standard method of ED-XRF, using 238 Pu (1.11 GBq) excitation source and laterite certified reference material as standards. The capability of INAA using neutrons from a Pu-Be (10 7 n/s) source and Low-Background Gamma Spectrometer (LBGS) at InSTEC is studied. The determined concentration values for Ni, Co, Cu and Zn shows a different pollution degree according to Dutch regulations and US NOAA guidelines. (Author)

  15. Dynamics of competitive strategies in de-regulated industries: the case of the electricity industry in France; Dynamique des strategies concurrentielles dans un contexte de liberalisation: le cas de l'industrie electrique en France

    Energy Technology Data Exchange (ETDEWEB)

    Cateura, O

    2007-11-15

    This research work is focused on the competitive dynamics approach and rivalry studies between competitors. It develops theses recent perspectives and particularly multi-market competition (also called multipoint competition) in de-regulated industries (network utilities). Indeed, competitive behaviours in liberalized industries are still badly-known. To conduct this research, we decided to analyze a selection of companies (EDF, Electrabel, Endesa, Enel, Gaz de France, Poweo, Direct Energie..) settled on the French electricity market presently in the course of liberalization (1996 - 2006). This qualitative research, through longitudinal case studies, has been developed thanks to a CIFRE agreement (between the French Ministry of Research and the firm Electrabel France) including action research and participant observation. Using multidimensional strategic sequences, we identified two periods, the first one characterized by a confrontation movement and a second one by mutual forbearance. We argue that after learning the rules of a newly liberalized market (confrontation, diversification, internationalization), competitors rapidly and collectively shift there positions towards a focused European strategy based on the gas-electricity convergence. The development of multi-market competition has conducted to mutual forbearance, which was particularly profitable to the major participants. Integrated strategy (market and non-market) appears as an important driver for legitimizing theses behaviours. (author)

  16. Dynamics of competitive strategies in de-regulated industries: the case of the electricity industry in France; Dynamique des strategies concurrentielles dans un contexte de liberalisation: le cas de l'industrie electrique en France

    Energy Technology Data Exchange (ETDEWEB)

    Cateura, O

    2007-11-15

    This research work is focused on the competitive dynamics approach and rivalry studies between competitors. It develops theses recent perspectives and particularly multi-market competition (also called multipoint competition) in de-regulated industries (network utilities). Indeed, competitive behaviours in liberalized industries are still badly-known. To conduct this research, we decided to analyze a selection of companies (EDF, Electrabel, Endesa, Enel, Gaz de France, Poweo, Direct Energie..) settled on the French electricity market presently in the course of liberalization (1996 - 2006). This qualitative research, through longitudinal case studies, has been developed thanks to a CIFRE agreement (between the French Ministry of Research and the firm Electrabel France) including action research and participant observation. Using multidimensional strategic sequences, we identified two periods, the first one characterized by a confrontation movement and a second one by mutual forbearance. We argue that after learning the rules of a newly liberalized market (confrontation, diversification, internationalization), competitors rapidly and collectively shift there positions towards a focused European strategy based on the gas-electricity convergence. The development of multi-market competition has conducted to mutual forbearance, which was particularly profitable to the major participants. Integrated strategy (market and non-market) appears as an important driver for legitimizing theses behaviours. (author)

  17. The development of computer industry and applications of its relevant techniques in nuclear research laboratories

    International Nuclear Information System (INIS)

    Dai Guiliang

    1988-01-01

    The increasing needs for computers in the area of nuclear science and technology are described. The current status of commerical availabe computer products of different scale in world market are briefly reviewed. A survey of some noticeable techniques is given from the view point of computer applications in nuclear science research laboratories

  18. Application of modelling techniques in the food industry: determination of shelf-life for chilled foods

    NARCIS (Netherlands)

    Membré, J.M.; Johnston, M.D.; Bassett, J.; Naaktgeboren, G.; Blackburn, W.; Gorris, L.G.M.

    2005-01-01

    Microbiological modelling techniques (predictive microbiology, the Bayesian Markov Chain Monte Carlo method and a probability risk assessment approach) were combined to assess the shelf-life of an in-pack heat-treated, low-acid sauce intended to be marketed under chilled conditions. From a safety

  19. Molecular techniques for the identification and detection of microorganisms relevant for the food industry

    NARCIS (Netherlands)

    Klijn, N.

    1996-01-01

    The research described in this thesis concerns the development and application in food microbiology of molecular identification and detection techniques based on 16S rRNA sequences. The technologies developed were applied to study the microbial ecology of two groups of bacteria, namely

  20. Air Conditioning Compressor Air Leak Detection by Image Processing Techniques for Industrial Applications

    Directory of Open Access Journals (Sweden)

    Pookongchai Kritsada

    2015-01-01

    Full Text Available This paper presents method to detect air leakage of an air conditioning compressor using image processing techniques. Quality of air conditioning compressor should not have air leakage. To test an air conditioning compressor leak, air is pumped into a compressor and then submerged into the water tank. If air bubble occurs at surface of the air conditioning compressor, that leakage compressor must be returned for maintenance. In this work a new method to detect leakage and search leakage point with high accuracy, fast, and precise processes was proposed. In a preprocessing procedure to detect the air bubbles, threshold and median filter techniques have been used. Connected component labeling technique is used to detect the air bubbles while blob analysis is searching technique to analyze group of the air bubbles in sequential images. The experiments are tested with proposed algorithm to determine the leakage point of an air conditioning compressor. The location of the leakage point was presented as coordinated point. The results demonstrated that leakage point during process could be accurately detected. The estimation point had error less than 5% compared to the real leakage point.

  1. An Overview on Measurement-While-Drilling Technique and its Scope in Excavation Industry

    Science.gov (United States)

    Rai, P.; Schunesson, H.; Lindqvist, P.-A.; Kumar, U.

    2015-04-01

    Measurement-while-drilling (MWD) aims at collecting accurate, speedy and high resolution information from the production blast hole drills with a target of characterization of highly variable rock masses encountered in sub-surface excavations. The essence of the technique rests on combining the physical drill variables in a manner to yield a fairly accurate description of the sub-surface rock mass much ahead of following downstream operations. In this light, the current paper presents an overview of the MWD by explaining the technique and its set-up, the existing drill-rock mass relationships and numerous on-going researches highlighting the real-time applications. Although the paper acknowledges the importance of concepts of specific energy, rock quality index and a couple of other indices and techniques for rock mass characterization, it must be distinctly borne in mind that the technique of MWD is highly site-specific, which entails derivation of site-specific calibration with utmost care.

  2. Problem-solving and developing quality management methods and techniques on the example of automotive industry

    Directory of Open Access Journals (Sweden)

    Jacek Łuczak

    2015-12-01

    Full Text Available The knowledge about methods and techniques of quality management together with their effective use can be definitely regarded as an indication of high organisational culture. Using such methods and techniques in an effective way can be attributed to certain level of maturity, as far as the quality management system in an organisation is concerned. There is in the paper an analysis of problem-solving methods and techniques of quality management in the automotive sector in Poland. The survey was given to the general population, which in case of the study consisted of companies operating in Poland that had certified quality management systems against ISO/TS 16949. The results of the conducted survey and the conclusions of the author can show actual and potential OEM suppliers (both 1st and 2nd tier in which direction their strategies for development and improvement of quality management systems should go in order to be effective. When the universal character of methods and techniques used in the surveyed population of companies is taken into consideration, it can be assumed that the results of the survey are also universal for all organisations realising the TQM strategy. The results of the research confirmed that methods which are also the basis for creating key system documents are the most relevant ones, i.e. flowcharts and FMEA, and moreover process monitoring tools (SPC and problem solving methods -above all 8D.

  3. Productivity Improvement in a Steel Industry using Supply Chain Management Technique

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Soltani

    2013-06-01

    Full Text Available Cost reduction is one of the methods applied for improving the productivity of organizations. In productivity literature, particularly in nonparametric methods, cost reduction related methods are regarded as input oriented models. This paper presents a Supply Chain Management (SCM model in which purchasing iron ore and coke from different resources, along with production and distribution of steel products were investigated to improve the productivity of a steel making plant in Iran. The model was designed based on a single objective concept with a focus on total cost minimization. The constraints of the model consisted principal restriction concerning mines, coke plant and products. The model was implemented in steel factories (blast furnace affiliated with Iranian Mines and Mining Industries Development and Renovation Organization (IMIDRO.The results showed that the priority for providing iron ore should be given to Iran Central Iron Ore Company (ICIOC which has enough production capacity to satisfy the required ores. The results further suggested that at the best productivity condition, Isfahan steel plant should focus on the beam and bar production. The other plants, i.e. Zagros plant, should focus on L-beam and slab and finally Meibod steel plant should concentrate on slab production. It was also showed that the coke production plants cannot supply the required tonnage of the steel plants. Therefore, some new plants should be established to achieve self-sufficiency in this industry. This model can be used as a support tool for decision-makers at strategic and tactical decision levels.

  4. Techniques and methodologies to identify potential generated industries of NORM in Angola Republic and evaluate its impacts

    International Nuclear Information System (INIS)

    Diogo, José Manuel Sucumula

    2017-01-01

    Numerous steps have been taken worldwide to identify and quantify the radiological risks associated with the mining of ores containing Naturally Occurrence Radioactive Material (NORM), often resulting in unnecessary exposures to individuals and high environmental damage, with devastating consequences for the health of workers and damage to the economy of many countries due to a lack of regulations or inadequate regulations. For these and other reasons, the objective of this work was to identify industrial potential generating NORM in the Republic of Angola and to estimate its radiological environmental impacts. To achieve this objective, we studied the theoretical aspects, identified the main internationally recognized industrial companies that as generate by NORM. The Brazilian experience in the regulatory aspect was observed in the evaluation criteria to classify industries that generate NORM, the methods of mining and its radiological environmental impacts, as well as the main techniques applied to evaluate the concentrations of radionuclides in a specific environmental matrix and/or a NORM sample. The study approach allowed the elaboration of a NORM map for the main provinces of Angola, establishing the evaluation criteria for implementing the Radiation Protection Plan in the extractive industry, establishing measures to control ionizing radiation in mining, identifying and quantifying radionuclides present in samples of lees oil. However, in order to assess adequately the radiological environmental impact of the NORM industry, it is not enough to identify them, it is important to know the origin, quantify the radioactive material released as liquid and gaseous effluents, identify the main routes of exposure and examine how this material spreads into the environment until it reaches man. (author)

  5. Barriers to implement green supply chain management in automobile industry using interpretive structural modeling technique: An Indian perspective

    Directory of Open Access Journals (Sweden)

    Sunil Luthra

    2011-07-01

    Full Text Available Purpose: Green Supply Chain Management (GSCM has received growing attention in the last few years. Most of the automobile industries are setting up their own manufacturing plants in competitive Indian market. Due to public awareness, economic, environmental or legislative reasons, the requirement of GSCM has increased.  In this context, this study aims to develop a structural model of the barriers to implement GSCM in Indian automobile industry.Design/methodology/approach: We have identified various barriers and contextual relationships among the identified barriers. Classification of barriers has been carried out based upon dependence and driving power with the help of MICMAC analysis. In addition to this, a structural model of barriers to implement GSCM in Indian automobile industry has also been put forward using Interpretive Structural Modeling (ISM technique. Findings: Eleven numbers of relevant barriers have been identified from literature and subsequent discussions with experts from academia and industry. Out of which, five numbers of barriers have been identified as dependent variables; three number of barriers have been identified as the driver variables and three number of barriers have been identified as the linkage variables. No barrier has been identified as autonomous variable. Four barriers have been identified as top level barriers and one bottom level barrier. Removal of these barriers has also been discussed.Research limitations/implications: A hypothetical model of these barriers has been developed based upon experts’ opinions. The conclusions so drawn may be further modified to apply in real situation problem. Practical implications: Clear understanding of these barriers will help organizations to prioritize better and manage their resources in an efficient and effective way.Originality/value: Through this paper we contribute to identify the barriers to implement GSCM in Indian automobile industry and to prioritize them

  6. Mineral resources accounting: A technique formonitoring the Philippine mining industry for sustainable development

    Science.gov (United States)

    Santos, Teodoro M.; Zaratan, May L.

    Mining which extracts exhaustible mineral resources has been condemned by certain sectors as promoting social inequity and underdevelopment. This is so because once a tonne of copper, say, is mined it is forever lost to the future generation. Such perception translates into policies that are usually disadvantageous or even hostile to the industry. Despite this adverse criticism, recent developments in natural resources accounting indicate that mining can truly contribute to the sustainable economic development of a society. True worth of mining in economic development can be assessed and monitored on a continuing basis through an appropriate system of natural accounts (SNA). If the industry is found deficient, such SNA can also point out how the industry can be made to constribute to sustainable growth. The prevailing SNA is criticized as having failed to capture the adverse effects on the welfare of society of producing a nonrenewable resource such as minerals. For instance, the production of copper for a particular year registers an increase in gross national product equivalent to its monetary value. However, the concomitant depletion of the country's natural wealth due to such production is nowhere recorded in the SNA. This faulty accounting gives rise to policies that result in nonsustainable economic growth. In order to address the preceding problem, this paper presents an accounting formula applicable to any nonrenewable resource whereby revenue is decomposed into income and capital components. To achieve sustainable economic growth, it states that the capital component must be invested to generate future incomes. However, investments need not be confined to the same sector. Application of the accounting scheme to the Philippine copper and gold sectors during the 1980-1990 period leads to the following conclusions: (a) by and large, gold and copper mining operations have indeed contributed positively to national income, contrary to allegations of certain

  7. UTILISATION OF BENCHMARKING TECHNIQUES FOR FUNDAMENTING DEVELOPMENT STRATEGIES IN THE MANUFACTURING INDUSTRY IN ROMANIA

    Directory of Open Access Journals (Sweden)

    Geambasu Cristina Venera

    2011-07-01

    Full Text Available Benchmarking is a method used to measure the products, services and processes in comparison to an entity recognized as a leader in terms of performance of its operations. Used in the years 1970-1980 in the strategic management of the company currently has proven to be increasingly useful in many areas, including in international analysis models. In the European Union benchmarking indicators are used especially in the digital economy and as perspective indicators for 2011-2015 (Eurostat, Database. In the introduction we present and define forms of benchmarking, as well as a number of specific terms, which contribute to a better understanding of the content of this scientific work. Time series are used to highlight advances in labor productivity in EU countries, and the analysis is particularized for two countries: Romania and Germany. Quantitative data were collected from the source Eurostat website. A comprehensive indicator at macroeconomic level is resource productivity, representing GDP in relation with domestic consumption of material (DCM. DCM measures the amount of materials used directly by an economy. It is presented in tabular form for all European Union countries and Switzerland, as evolving over a period of eight years. Benchmarking method is used to highlight some differences (gaps between EU countries regarding productivity and particularly the one between Germany and Romania is highlighted, concerning the performance of manufacturing industries. It is expected that this gap will diminish. The gap was highlighted by relevant graphics and interpretations. The second part of the paper focuses on comparative analysis of factors productivity using the production function. We analyze labor and capital productivity and other factors that determine the level of production. For highlighting the contribution of the labour factor we used the number of hours worked, considering that it reflects the analyzed phenomenon more realistically. For

  8. Performance evaluation using bootstrapping DEA techniques: Evidence from industry ratio analysis

    OpenAIRE

    Halkos, George; Tzeremes, Nickolaos

    2010-01-01

    In Data Envelopment Analysis (DEA) context financial data/ ratios have been used in order to produce a unified measure of performance metric. However, several scholars have indicated that the inclusion of financial ratios create biased efficiency estimates with implications on firms’ and industries’ performance evaluation. There have been several DEA formulations and techniques dealing with this problem including sensitivity analysis, Prior-Ratio-Analysis and DEA/ output–input ratio analysis ...

  9. Brand Switching Pattern Discovery by Data Mining Techniques for the Telecommunication Industry in Australia

    Directory of Open Access Journals (Sweden)

    Md Zahidul Islam

    2016-11-01

    Full Text Available There is more than one mobile-phone subscription per member of the Australian population. The number of complaints against the mobile-phone-service providers is also high. Therefore, the mobile service providers are facing a huge challenge in retaining their customers. There are a number of existing models to analyse customer behaviour and switching patterns. A number of switching models may also exist within a large market. These models are often not useful due to the heterogeneous nature of the market. Therefore, in this study we use data mining techniques to let the data talk to help us discover switching patterns without requiring us to use any models and domain knowledge. We use a variety of decision tree and decision forest techniques on a real mobile-phone-usage dataset in order to demonstrate the effectiveness of data mining techniques in knowledge discovery. We report many interesting patterns, and discuss them from a brand-switching and marketing perspective, through which they are found to be very sensible and interesting.

  10. Google Livres et le futur des bibliothèques numériques historique du projet, techniques documentaires, alternatives et controverses

    CERN Document Server

    Jacquesson, Alain

    2010-01-01

    En 2004, le monde du livre apprend le projet fou de deux jeunes illuminés : construire en cinq ans une bibliothèque numérique universelle. Six ans plus tard, une gigantesque bibliothèque numérique de plus de 12 millions de volumes a vu le jour. Des collections, que des générations de conservateurs ont mis des siècles à constituer, sont avalées par Google Livres. Jamais une collaboration d'une telle envergure entre les secteurs publics et privés n'avait été entreprise dans le domaine patrimonial. Dans le monde entier, les chercheurs comme le grand public s'habituent peu à peu à utiliser Google Livres, qui dit viser maintenant 30 millions de livres numériques. Cette réalisation a nécessité l'élaboration de compétences informatiques spécifiques, notamment en ce qui concerne la numérisation de masse. L'efficacité de ce savoir-faire a suscité l'intérêt de nombreuses bibliothèques qui ont choisi de participer au projet. Cette appropriation des biens publics soulève aussi de nombreuses c...

  11. Development of satellite remote sensing techniques as an economic tool for forestry industry

    Science.gov (United States)

    Sader, Steven A.; Jadkowski, Mark A.

    1989-01-01

    A cooperative commercial development project designed to focus on cost-effective and practical applications of satellite remote sensing in forest management is discussed. The project, initiated in September, 1988 is being executed in three phases: (1) development of a forest resource inventory and geographic information system (GIS) updating systems; (2) testing and evaluation of remote-sensing products against forest industry specifications; and (3) integration of remote-sensing services and products in an operational setting. An advisory group represented by eleven major forest-product companies will provide direct involvement of the target market. The advisory group will focus on the following questions: Does the technology work for them? How can it be packaged to provide the needed forest-management information? Can the products and information be provided in a cost-effective manner?

  12. Application of multi-element clustering techniques of five Egyptian industrial sugar products

    International Nuclear Information System (INIS)

    Awadallah, R.M.; Mohamed, A.E.

    1995-01-01

    The concentration of 18 elements in different cane sugar products, i.e., cane sugar plants, crude and syrup juices, molasses, and the end products of the consumer sugar, were analyzed and processed. The samples were collected from five cities, i.e., Kom Ombo, Edfu, Armant, Deshna and Naga Hammady in Upper Egypt where the main Egyptian sugar industry factories are located. INAA was applied for the determination of Al, Ca, Cl, Co, Cr, Fe, Mg, Mn, Na, and Sc, while Cu, Li, P, Sn, V and Zn were determined by ICP-AES and Pb and As were determined by AAS. These three analytical methods were applied to optimize the sensitivity and the accuracy of the measurements in order to provide a sound basis for the obtention of reliable clustering results. (author). 5 refs., 8 figs., 3 tabs

  13. Reliability of non-destructive test techniques in the inspection of pipelines used in the oil industry

    International Nuclear Information System (INIS)

    Carvalho, A.A.; Rebello, J.M.A.; Souza, M.P.V.; Sagrilo, L.V.S.; Soares, S.D.

    2008-01-01

    The aim of this work is to evaluate the reliability of non-destructive test (NDT) techniques for the inspection of pipeline welds employed in the petroleum industry. Radiography, manual and automatic ultrasonic techniques using pulse-echo and time of flight diffraction (TOFD) were employed. Three classes of defects were analyzed: lack of penetration (LP), lack of fusion (LF) and undercut (UC). The tests were carried out on specimen made from pipelines containing defects, which had been artificially inserted on laying the weld bead. The results showed the superiority of the automatic ultrasonic tests for defect detection compared with the manual ultrasonic and radiographic tests. Additionally, artificial neural networks (ANN) were used in the detection and automatic classification of the defects

  14. Origin and tracing techniques of high 15N nitrogen compounds in industrial environments

    International Nuclear Information System (INIS)

    Talma, A.S.; Meyer, R.

    2002-01-01

    Effluents and process waters from various industrial plants were investigated for the 15 N/ 14 N isotope ratio in nitrate and ammonia. It was found that large isotope fractionation occurs in cases where ammonia is involved in gas-liquid phase changes. This feature was found to occur in two coke oven plants where ammonia gas is removed from a gas stream by solution in water, in an ammonia sulphate plant where ammonia gas is absorbed in sulphuric acid and in a water treatment plant where ammonia is removed from (high pH) water by blowing air through the process water. In all these cases 15 N isotope enrichments (in the range of 10 to 30 per mille) occurred. These enrichments are in excess of those found naturally. Ammonia in such wastewaters essentially retains this high 15 N content when it is converted to nitrate underground: which occurs rapidly under well-oxidised conditions. Nitrate is a fairly conservative tracer and its contamination in water can be followed readily. In the low recharge environment in the central parts of South Africa evidence of waste management practices of 10-20 years earlier were still quite evident using this isotopic label. The high 15 N nitrate signal could be used to distinguish industrial nitrogen pollution from pollution by local sewage disposal systems. Vegetation that derives its nitrogen from such high 15 N sources retains the isotope signature of its source. Grass and other annual plants then exhibit the isotope signature of the water of a specific year. Trees exhibit the isotope signature of deeper water, which shows the effects of longer term pollution events. The use of high 15 N as tracer enables the source apportionment of nitrogen derived pollution in these specific circumstances. (author)

  15. Réseau des développeurs - logiciels d'exploitation libre pour ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Un atelier technique réunissant des utilisateurs, des développeurs et des promoteurs des logiciels libres sera organisé pour mettre au point une application prototype - des formulaires électroniques permettant de saisir des données au moyen d'un ANP puis de les transférer dans un ordinateur - pouvant combler les ...

  16. Industrial waste - destination and valuation techniques of floating hoses: case study in Macaé, RJ

    Directory of Open Access Journals (Sweden)

    Marlon de Almeida Clemente Silva

    2017-10-01

    Full Text Available A large part of the oil extracted in Brazil today, is drained to the coast, or even transported to larger vessels through Floating Hoses. This oil unloading operation is called Offloading, it is of fundamental importance for the performance of offshore operations. These operating units use storage systems and oil relief, which can be FSO (Floating Storage Unit and Transfer or FPSO (Floating Production Unit, Stockpiling and Transfer. In this oil transshipment scenario, floating hoses have primary role therefore they are responsible for this operation. The Floating Hoses after useful life are discarded. How do the environmentally correct disposal of this waste? The destination most used for this waste are the landfills Class 2, for non-hazardous waste. In this study, we attempted to develop appropriate allocation techniques for Floating Hose, in order to obtain a greater appreciation potential of the materials that compose it, as well as presenting the risk of these being put up in a landfill, even if it is a controlled landfill. This technique is based on a so-called Reverse Manufacturing, all components are reused and recovered, with a more environmentally sound and economically viable destination. The research methodology was based on empirical studies of phenomenological framework, involving operational staff of a medium-sized company with a rising share of Treatment and Waste Disposal Market, in the city of Macaé. It was evidenced in the survey that there is a possibility of potential gains from the application of reverse manufacturing techniques of hoses, both in terms of environmental liability reductions and the financial return through the recovery of materials that compose them.

  17. The tracer technique, an extensive field of application for research and industry

    International Nuclear Information System (INIS)

    Frevert, E.

    1980-10-01

    First the principle of the tracer technique is described. Then the most important applications are reported as there are measurements of velocities of flow and of running through, of charges of amount, of durations and of volumes, investigations of intermixtures, distributions and of corrosion, wear and lubricant phenomenous, locatings of leakages, checkings of tightnesses and determinations of the efficiencies of destilling and purifying plants. For each field of application examples are given, most of them investigations of the DEPARTMENT FOR ISOTOPE APPLICATION of the AUSTRIAN RESEARCH CENTRE SEIBERSDORF Ges.m.b.H. Further applications in chemistry, metallurgy, medicine, biology and agriculture are mentioned. (author)

  18. Radioactive tracer technique in process optimization: applications in the chemical industry

    International Nuclear Information System (INIS)

    Charlton, J.S.

    1989-01-01

    Process optimization is concerned with the selection of the most appropriate technological design of the process and with controlling its operation to obtain maximum benefit. The role of radioactive tracers in process optimization is discussed and the various circumstances under which such techniques may be beneficially applied are identified. Case studies are presented which illustrate how radioisotopes may be used to monitor plant performance under dynamic conditions to improve production efficiency and to investigate the cause of production limitations. In addition, the use of sealed sources to provide information complementary to the tracer study is described. (author)

  19. First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

    Energy Technology Data Exchange (ETDEWEB)

    Antoni, Rodolphe; Passard, Christian; Perot, Bertrand [CEA Cadarache DEN/Nuclear Measurement Laboratory, 13108 Saint-Paul lez Durance (France); Batifol, Marc; Vandamme, Jean-Christophe [Nuclear Measurement Team, AREVA NC, La Hague plant F-50444 Beaumont-Hague (France); Grassi, Gabriele [AREVA NC, 1 place Jean-Millier, 92084 Paris-La-Defense cedex (France)

    2015-07-01

    The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and {sup 235}U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

  20. A contribution to the characterisation of natural and industrial crystalline emissions using electron beam and X-ray techniques

    International Nuclear Information System (INIS)

    Riedel, F.N.

    1980-01-01

    In this work the composition of dusts of different origin is studied based on the assumption that natural and industrial emissions sources may possibly be differentiated by the emission of characteristic minerals and compounds. Only if some of these compounds or certain groups of compounds can be associated with a distinct emission source, such compounds may be considered as guiding compounds or guiding minerals. In this case the emission sources should be identified unambiguously even over large distances. In the air pollution studies performed in the past, the emphasis has been laid mainly on gases like SO 2 , CO, CO 2 , NOsub(x), and HF, without paying much attention to the crystalline and amorphous components, which are present simultaneously. This study is restricted to the dust-like component of natural and industrial emission sources to get more information on its composition. In part these emissions are less dangerous in the compound state, as for example fluorine in the mica type mineral muskovite (KAl 2 [(OH,F) 2 AlSi 3 O 10 ]. As a working hypothesis it has been assumed that based on a series of investigations these compounds can be identified using electron miscroscopy and electron diffraction. In the presence of larger quantities of emission materials also X-ray techniques as Debye-Scherrer- or gonio methods can be applied. Reliable results can only be obtained by an investigation covering a broad area of industrial production. (orig./RW) [de

  1. First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

    International Nuclear Information System (INIS)

    Antoni, Rodolphe; Passard, Christian; Perot, Bertrand; Batifol, Marc; Vandamme, Jean-Christophe; Grassi, Gabriele

    2015-01-01

    The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and 235 U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

  2. The use of tomographic techniques in the mineral processing Industry. A review

    International Nuclear Information System (INIS)

    Witika, L.K.; Jere, E.H.

    2002-01-01

    Process tomographic techniques may be used to analyse the internal state of most of the multiphase process engineering systems such as material segregation in a reactor multiphase flow in pipes and the spatial resolution of mineral grains in multiphase particles. These techniques include radiation computed tomography (X-ray or ray), electrical methods(capacitance, impedance and inductive tomography) positron emission tomography,optical tomography, microwave tomography, acoustic tomographical methods and many more. Many potential applications exist for process tomographic instrumentation for quantitative analysis and fault-detection purposes. Amongst these, electrical methods are widely used for those mineral processes deserving particular attention such as dense-medium separation, hydro cyclones, flotation cells and columns, gas-liquid absorbers, solvent extraction and other liquid-liquid processes, filtration and other solid-liquid processes, grinding mills (both dry and wet, conveyors and hoppers). Development in on-line measurement instrumentation now allow direct observation of the behaviour of fluids inside mineral separation equipment. This offers the possibility to acquire process data to enable models to be devised, to verify theoretical computational fluid dynamics predictions and control of various unit processes. In this review, the most important tomographic sensing methods are reviewed. Examples of the implementation of some electrical methods are illustrated. (authors)

  3. Radioactive Particle Tracking (RPT): The Powerful Industrial Radiotracer Techniques for Hydrodynamics and Flow Visualization Studies

    International Nuclear Information System (INIS)

    Mohd Amirul Syafiq Mohd Yunos

    2016-01-01

    Full text: Radioactive particle tracking (RPT) techniques have been widely applied in the field of chemical engineering, especially in hydrodynamics in multiphase reactors. This technique is widely used to monitor the motion of the flow inside a reactor by using a single radioactive particle tracer that is neutrally buoyant with respect to the phase is used as a tracker. The particle moves inside the volume of interest and its positions are determined by an array of scintillation detectors counting in coming photons. Particle position reconstruction algorithms have been traditionally used to map measured counts rate into the coordinates by solving a minimization problem between measured events and calibration data. RPT have been used to validate respective-scale CFD models to partial success. This presentation described an introduction to radioactive particle tracking and summarizing a history of such developments and the current state of this method in Malaysian Nuclear Agency, with a perspective towards the future and how these investigations may help scale-up developments. (author)

  4. Les conflits d’intérêts des groupes de défense de patients financés par l’industrie pharmaceutique : le cas du remboursement public des médicaments

    Directory of Open Access Journals (Sweden)

    Hughes, David

    2013-01-01

    Full Text Available Some patient interest groups and other pressure groups in the health sector solicit the pharmaceutical industry to obtain funding. I raise and discuss some issues that can result from this type of relationship.

  5. How Molecular Evolution Technologies can Provide Bespoke Industrial Enzymes: Application to Biofuels Comment les technologies d’évolution moléculaire peuvent fournir des enzymes industrielles sur mesure : application aux biocarburants

    Directory of Open Access Journals (Sweden)

    Fourage L.

    2013-08-01

    est l’un des principaux goulets d’étranglement dans le développement de la conversion biologique de la biomasse lignocellulosique en biocarburants. L’un des organismes les plus efficaces pour la production d’enzymes cellulolytiques est le champignon Trichoderma reesei, principalement grâce à sa capacité importante de sécrétion. La conversion de la cellulose en glucose implique trois types de cellulases travaillant en synergie : les endoglucanases (EC 3.2.1.4 clivant de façon aléatoire les liaisons glycosidiques en (3-1,4, les cellobiohydrolases (EC 3.2.1.91 attaquant la chaîne de cellulose aux deux extrémités afin de produire le cellobiose, dimère qui sera converti en glucose par l’action des (3-glucosidases (EC 3.2.1.21. De façon inattendue, la quantité de 3-glucosidase (BGL1 sécrétée par les souches de T. reesei représente un très faible pourcentage de la quantité totale des protéines sécrétées qui en fait donc une activité limitante du cocktail. Cette faible activité limite d’autant plus les performances du cocktail que le cellobiose représente le principal inhibiteur de la réaction cellulolyse par les cellobiohydrolases. Ce goulot d’étranglement peut être atténué soit par une surexpression de la (3-glucosidase chez T. reesei, soit par une amélioration de son activité spécifique. Après un bref aperçu des principales technologies existantes, cet exemple sera utilisé dans cette revue pour illustrer le potentiel des technologies d’évolution dirigée pour développer des enzymes répondant aux besoins de l’industrie des biotechnologies. Nous décrivons comment la mise en oeuvre d’une stratégie d’évolution dirigée par le L-ShufflingTM avec trois gènes parentaux provenant de la biodiversité microbienne permet d’obtenir des activités (3-glucosidases très améliorées par rapport à la Cel3a (3-glucosidase de T. reesei (activité spécifique 242 fois plus élevée pour le substrat pNPGIc. Cette am

  6. Analysis of industrial flame characteristics and constancy study using image processing technique

    Directory of Open Access Journals (Sweden)

    Bibhuti Bhusan Samantaray

    2015-12-01

    Full Text Available The study of characterizing and featuring different kinds of flames has become more important than ever in order to increase combustion efficiency and decrease particulate emissions, especially since the study of industrial flames requires more attention. In the present work, different kinds of combustion flames have been characterized by means of digital image processing (DIP in a 500 kW PF pilot swirl burner. A natural gas flame and a set of pulverized fuel flames of coal and biomass have been comparatively analyzed under co-firing conditions. Through DIP, statistical and spectral features of the flame have been extracted and graphically represented as two-dimensional distributions covering the root flame area. Their study and comparison leads to different conclusions about the flame behavior and the effect of co-firing coal and biomass in pulverized fuel flames. Higher oscillation levels in co-firing flames versus coal flames and variations in radiation regimen were noticed when different biomasses are blended with coal and brought under attention.

  7. Treatment of industrial wastewater by electrochemical techniques; Depurazione di reflui industriali mediante tecniche elettrochimiche

    Energy Technology Data Exchange (ETDEWEB)

    Panizza, M.; Cerisola, G. [Genua Univ., Genua (Italy). Dipt. di Ingegneria Chimica e di Processo

    2000-05-01

    This work analyses the applicability of electrochemical treatments of an industrial effluent containing organic compounds such as naphthalene-and anthraquinon-sulphonic acids. Two indirect electrolysis, which generate hypochlorite ions and hydrogen peroxide as chemical reactants, were studied. The optimum conditions of the processes were found and the results compared. Better performances were obtained electro generating in situ hypochlorite ions than with hydrogen peroxide. With the hypochlorite ions, as redox reagent, the effluent was decolorized and COD was removed up to value of 100 mg l{sup -}1. [Italian] Questo lavoro e' volto all'analisi dell'applicabilita' dei trattamenti elettrochimici per lo smaltimento di un refluo industriale contenente composti organici biorefrattari come gli acidi naftalen- ed natrachinon-solforici. A tale proposito sono stati studiati due processi di elettrolisi indiretta che generano in situ lo ione ipoclorito ed il perossido di idrogeno come reagenti chimici ossidanti. Sono state trovate le condizioni ottimali dei due trattamenti e sono stati confrontati i risultati. Dai risultati sperimentali si e' concluso che elettrogenerando in situ lo ione ipoclorito si ottiene una ossidazione migliore rispetto al perossido di idrogeno. Con lo ione ipoclorito come reagente redox, il refluo e' stato decolorato ed il suo COD e' stato rimosso fino a valori di 100 mg l{sup -}1.

  8. An industry-scale mass marking technique for tracing farmed fish escapees.

    Directory of Open Access Journals (Sweden)

    Fletcher Warren-Myers

    Full Text Available Farmed fish escape and enter the environment with subsequent effects on wild populations. Reducing escapes requires the ability to trace individuals back to the point of escape, so that escape causes can be identified and technical standards improved. Here, we tested if stable isotope otolith fingerprint marks delivered during routine vaccination could be an accurate, feasible and cost effective marking method, suitable for industrial-scale application. We tested seven stable isotopes, (134Ba, (135Ba, (136Ba, (137Ba, (86Sr, (87Sr and (26Mg, on farmed Atlantic salmon reared in freshwater, in experimental conditions designed to reflect commercial practice. Marking was 100% successful with individual Ba isotopes at concentrations as low as 0.001 µg. g-1 fish and for Sr isotopes at 1 µg. g-1 fish. Our results suggest that 63 unique fingerprint marks can be made at low cost using Ba (0.0002 - 0.02 $US per mark and Sr (0.46 - 0.82 $US per mark isotopes. Stable isotope fingerprinting during vaccination is feasible for commercial application if applied at a company level within the world's largest salmon producing nations. Introducing a mass marking scheme would enable tracing of escapees back to point of origin, which could drive greater compliance, better farm design and improved management practices to reduce escapes.

  9. Heat management in motor vehicles 3. Development methods and innovations in heat management in passenger cars and industrial vehicles; Waermemanagement des Kraftfahrzeugs 3. Entwicklungsmethoden und Innovationen der Kfz- und Nfz-Waermetechnik

    Energy Technology Data Exchange (ETDEWEB)

    Deussen, N. (ed.) [Fachhochschule Koeln (Germany). Labor fuer Verbrennungsmotoren und Applikation

    2002-07-01

    The proceedings volume outlines problem solutions, development strategies and design methods relating to heat management in motor vehicles. The focus is on utilisation, supply, transmission and release of heat in passenger cars and industrial vehicles. The complete state of the art is reviewed, with the focus on the following subjects: The potential of heat management in terms of performance and comfort; Future strategies for optimisation of thermal processes; Expert knowledge in component and system innovations; Status and perspectives of user software; Engine cooling, vehicle air conditioning, heat protection; Methodology; Numeric fluid mechanics; Heat transfer; Practical applications of thermal engineering, Heat management in engines; Thermal system optimisation; CFD; Future numeric methods in heat transfer and fluid mechanics; Methods of measurement and instrumentation. [German] Der Tagungsband informiert in einem aktuellen Ueberblick ueber Problemloesungen, Entwicklungsstrategien und Auslegungsmethoden im Umfeld des Kraftfahrzeug-Waermemanagements. Dabei wird insbesondere auf die Optimierung der Nutzung, Bereitstellung, Uebertragung und Abgabe von Waerme fokussiert. Der Inhalt umfasst dabei Anwendungen bei Automobilen und Nutzfahrzeugen. Der Leser erhaelt einen konkreten Ueberblick ueber die Trends auf neuestem Stand der Technik. Besondere Schwerpunkte sind: Potenzial des Waermemanagements bezueglich Leistung und Kundennutzen - Zukunftsweisende Strategien zur Optimierung waermetechnischer Prozesse - Kompaktes Fachwissen bei Bauteil- und System-Innovationen - Stand der Technik und Zukunftsperspektive bei Anwendersoftware. Inhalt: Motorkuehlung - Fahrzeugklimatisierung - Hitzeschutz - Methoden der Waermetechnik - Numerische Stroemungsmechanik - Waermeuebertragung - Anwendungsbeispiele der Waermetechnik - Motor-Thermomanagement - Waermetechnische Systemoptimierung - CFD - Zukuenftige numerische Methoden der Waermeuebertragung und Stroemungsmechanik - Messtechnik

  10. First industrial application of the auto-adaptative MAG STT welding technique with laser joint tracking

    International Nuclear Information System (INIS)

    Tran Tien, Th.

    2007-01-01

    The Welding Institute has participated to the plan of construction of the Large Hadron Collider. The hoops of the dipolar magnets are composed of two half cylinders 15 m in length in 10 mm 316LN austenitic stainless steel and are assembled around the magnet in a horizontal-vertical position. The Welding Institute has developed a software for carrying out the auto-adaptative welding technique with laser joint tracking, in using the MAG STT (Surface Tension Transfer) process. The modelling of the welding laws and the strategy of filling the joints in multi-paths absorb the physical tolerances of the preparation (clearance, poor alignment, root..) in dynamic welding condition too. (O.M.)

  11. Progress in radiation protection techniques for workers in the nuclear industry

    International Nuclear Information System (INIS)

    Pradel, J.; Zettwoog, P.; Rouyer, J.L.

    1982-01-01

    The increasingly stringent safety requirements of workers and the general public in the face of occupational and in particular nuclear risks call for continual improvements in radiation protection techniques. The Institute of Protection and Nuclear Safety (IPSN), especially the Technical Protection Services belonging to the Protection Department, and also the various radiation protection services of the French Atomic Energy Commission's nuclear centres and Electricite de France (EDF) are carrying out substantial research and development programmes on the subject. For this reason, IPSN organized a specialists' meeting to take stock of the efforts being made and to try to identify what steps seem most promising or should have priority at the national level. The authors summarize the presentations and discussions on three topics: (1) Progress in the analysis of the mechanism of exposure of workers; (2) Progress achieved from the radiation protection standpoint in the field of facility design and instrumentation; and (3) Application of the optimization principle

  12. Radiation protection measurement techniques and the challenges encountered in industrial and medical environments

    International Nuclear Information System (INIS)

    2013-01-01

    Nowadays everybody is concerned by the use of ionizing radiations for diagnostic and therapy purposes. Radiation protection regulatory requirements are becoming more and more constraining and have an impact on the performance criteria required for measurement systems. The measurement of some radiation protection data requires the use of complex and costly devices, leading to hardly manageable constraints for the users. Do they have to be systematically implemented? How is it possible to reduce, control and optimize the medical exposures using new methodological approaches? During this conference the participants have shed light on some concrete situations and realisations in the environmental, nuclear industry and medical domains. The document brings together 34 presentations (slides) dealing with: 1 - Environmental monitoring and measurement meaning (P.Y. Emidy (EDF)); human radiation protection and measurement meaning (A. Rannou (IRSN)); Eye lens dosimetry, why and how? (J.M. Bordy (CEA)); critical and reasoned approach of the ISO 11929 standard about decision threshold and detection limit (A. Vivier (CEA)); Samples collection and low activities measurement in the environment (D. Claval (IRSN)); Dosemeters calibration, what is new? (J.M. Bordy (CEA)); Appropriateness of measurement means for radiological controls (P. Tranchant (Techman Industrie)); Pulsed fields dosimetric reference for interventional diagnosis (M. Denoziere (CEA)); Pulsed complex fields dosimetry (F. Trompier (IRSN)); DOSEO: a tool for dose optimization in radiological imaging (C. Adrien (CEA)); Eye lens dosimetry (R. Kramar, A. De Vita (AREVA)); Eye lens dosimetry - workers exposure and proper radiation protection practices (I. Clairand (IRSN)); Individual neutrons dosimetry - status of existing standards (F. Queinnec (IRSN)); Complex field neutron spectroscopy: any new tool? (V. Lacoste (IRSN)); Photon mini-beams dosimetry in radiotherapy: stakes and protocols (C. Huet (IRSN)); Reference and

  13. High-resolution X-ray imaging - a powerful nondestructive technique for applications in semiconductor industry

    International Nuclear Information System (INIS)

    Zschech, Ehrenfried; Yun, Wenbing; Schneider, Gerd

    2008-01-01

    The availability of high-brilliance X-ray sources, high-precision X-ray focusing optics and very efficient CCD area detectors has contributed essentially to the development of transmission X-ray microscopy (TXM) and X-ray computed tomography (XCT) with sub-50 nm resolution. Particularly, the fabrication of high aspect ratio Fresnel zone plates with zone widths approaching 15 nm has contributed to the enormous improvement in spatial resolution during the previous years. Currently, Fresnel zone plates give the ability to reach spatial resolutions of 15 to 20 nm in the soft and of about 30 to 50 nm in the hard X-ray energy range. X-ray microscopes with rotating anode X-ray sources that can be installed in an analytical lab next to a semiconductor fab have been developed recently. These unique TXM/XCT systems provide an important new capability of nondestructive 3D imaging of internal circuit structures without destructive sample preparation such as cross sectioning. These lab systems can be used for failure localization in micro- and nanoelectronic structures and devices, e.g., to visualize voids and residuals in on-chip metal interconnects without physical modification of the chip. Synchrotron radiation experiments have been used to study new processes and materials that have to be introduced into the semiconductor industry. The potential of TXM using synchrotron radiation in the soft X-ray energy range is shown for the nondestructive in situ imaging of void evolution in embedded on-chip copper interconnect structures during electromigration and for the imaging of different types of insulating thin films between the on-chip interconnects (spectromicroscopy). (orig.)

  14. The Feasibility of Bulk Crystallization as an Industrial Purification and Production Technique for Proteins

    Science.gov (United States)

    Judge, Russell A.; Forsythe, Elizabeth L.; Johns, Michael R.; Pusey, Marc L.; White, Edward T.

    1998-01-01

    Bulk crystallization in stirred vessels is used industrially for the recovery and purification of many inorganic and organic materials. Although much has been written on the crystallization of proteins for X-ray diffraction analysis, very little has been reported on the application of bulk crystallization in stirred vessels. In this study, a 1-liter, seeded, stirred, batch crystallizer was used with ovalbumin as a model protein to test the feasibility of this crystallization method as a recovery and purification process for proteins. Results were obtained for ovalbumin solubility, nucleation thresholds, crystal breakage and crystal growth kinetics in bulk solution under a range of operating conditions of pH and ammonium sulphate concentration (Judge et al., 1996). Experiments were also performed to determine the degree of purification that can be achieved by the crystallization of ovalbumin from a mixture of proteins. The effect of the presence of these proteins upon the ovalbumin crystal growth kinetics was also investigated (Judge et al., 1995). All of these aspects are essential for the design of bulk crystallization processes which have not previously been reported for proteins. Results from a second study that investigated the effect of structurally different proteins on the solubility, crystal growth rates and crystal purity of chicken egg white lysozyme are also presented (Judge et al., 1997). In this case face growth rates were measured using lysozyme purified by liquid chromatography and the effect of the addition of specific protein impurities were observed on the (110) and (101) crystal faces. In these two studies the results are presented to show the feasibility and purifying ability of crystallization as a production process for proteins.

  15. Papers of All-Polish Conference on Nuclear Techniques in Industry, Medicine, Agriculture and Environmental Protection; Referaty Krajowej Konferencji Technika Jadrowa w Przemysle, Medycynie, Rolnictwie i Ochronie Srodowiska

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    These proceedings comprise papers presented at All-Polish Conference on nuclear techniques in industry, medicine, agriculture and environmental protection. Most of the papers are in the field of uses of radiation sources and particle beams in industry, radiation chemistry, nuclear medicine and dosimetry, environmental sciences.

  16. Application of new fast-electronic techniques to the determination of the exact moment of particle detection; Application des techniques nouvelles de l'electronique rapide a la determination de l'instant precis de detection d'une particule

    Energy Technology Data Exchange (ETDEWEB)

    Hesse, M [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1965-06-01

    Fluctuations in the time response of photomultipliers employed in scintillation counting are studied and experimentally checked. Statistical measurements of the output pulses show that the relative variance of the time fluctuations is minimum for the portion located around the bending point of the leading edge. A shaping circuit using this property is described. Experimental results are given, showing an improvement of the resolving time. (author) [French] Les fluctuations de la reponse temporelle des photomultiplicateurs, utilises dans les detecteurs a scintillations, sont etudiees et mesurees experimentalement. L'etude statistique des signaux de sortie montre que les fluctuations en temps presentent une variance relative minimale pour la region situee autour du point d'inflexion du front de montee. Un circuit de mise en forme utilisant cette propriete est decrit. Des resultats experimentaux sont donnes; ils montrent une amelioration sensible du pouvoir de resolution. (auteur)

  17. Employment of the technique of radiotracers for analysis of industrial filters

    International Nuclear Information System (INIS)

    Ramos, Vitor Santos; Crispim, Verginia Reis

    2007-01-01

    The main aim of this work is to develop a methodology to evaluate the characteristics of porous media in filter using the radio-tracing technique. To do this, an experimental prototype filter made up of an acrylic cylinder, vertically mounted and supported on the lower side by a controlled leaking valve was developed. Two filters (spheres of acrylic and silica crystals) were used to check the movement of the water through the porous media using 123 I in its MIBG (iodine-123-meta-iodo benzyl-guanidine) form. Further up the filter an instantaneous injection of the substance makes it possible to see the passage of radioactive clouds through the two scintillatory detectors NaI (2x2) ' ' positioned before and immediately after the cylinder with the filtering element (porous media). The are caused by the detectors on the passage of the radioactive cloud are analyzed through statistical functions using the weighted moment method which makes it possible to calculate the Residence-Time (the amount of time the tracer takes to thoroughly pass through the filter) per the equation of dispersion in tubular flow and the one-directional flow of the radiotracer in the porous media. (author)

  18. Color image analysis technique for measuring of fat in meat: an application for the meat industry

    Science.gov (United States)

    Ballerini, Lucia; Hogberg, Anders; Lundstrom, Kerstin; Borgefors, Gunilla

    2001-04-01

    Intramuscular fat content in meat influences some important meat quality characteristics. The aim of the present study was to develop and apply image processing techniques to quantify intramuscular fat content in beefs together with the visual appearance of fat in meat (marbling). Color images of M. longissimus dorsi meat samples with a variability of intramuscular fat content and marbling were captured. Image analysis software was specially developed for the interpretation of these images. In particular, a segmentation algorithm (i.e. classification of different substances: fat, muscle and connective tissue) was optimized in order to obtain a proper classification and perform subsequent analysis. Segmentation of muscle from fat was achieved based on their characteristics in the 3D color space, and on the intrinsic fuzzy nature of these structures. The method is fully automatic and it combines a fuzzy clustering algorithm, the Fuzzy c-Means Algorithm, with a Genetic Algorithm. The percentages of various colors (i.e. substances) within the sample are then determined; the number, size distribution, and spatial distributions of the extracted fat flecks are measured. Measurements are correlated with chemical and sensory properties. Results so far show that advanced image analysis is useful for quantify the visual appearance of meat.

  19. Kinetic ion exchange studies in ultramarines by the radioactive tracer method; Etudes cinetiques d'echanges d'ions dans les outremers par la technique des traceurs radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    May, S; Goenvec, H; Pinte, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The possibility of ion exchanges in various ultramarines has been studied in the aqueous phase. The kinetics of the exchange reactions is followed by studying the behaviour of a radioactive ion, either in the solution of the exchanging salt or in the ultramarine itself. The sodium in the make-up of the ultramarine, is found to exchange with various ions in solution. The reaction speeds appear to be governed by a diffusion process inside the grains of ultramarine. The diffusion coefficients and the activation energies are determined for the exchanges studied. Several exchange studies were carried out in an organic medium. The kinetics of ion exchange is also investigated in ultramarines from which most of the constituent sulphur has been eliminated. The results obtained in these ultramarines are compared with the exchange kinetics of the same ions in ordinary ultramarine. (author) [French] Nous avons etudie la possibilite d'echanges ioniques dans differents outremers, en phase aqueuse. L'etude cinetique des reactions d'echanges est suivie en etudiant le comportement d'ion radioactif, soit dans la solution du sel echangeant, soit dans l'outremer lui-meme. C'est le sodium de constitution de l'outremer qui s'echange avec differents ions en solution. Les vitesses de reactions semblent etre controlees par un processus de diffusion a l'interieur des grains d'outremer. Les coefficients de diffusion et les energies d'activation sont determines pour les echanges etudies. Quelques etudes sont realisees en milieu organique ou quelques echanges ont ete etudies. La cinetique d'echange d'ions est egalement etudie dans des outremers dans lesquels la majorite du soufre de constitution a ete eliminee. On compare les resultats obtenus dans ces outremers avec les cinetiques d'echanges des memes ions dans l'outremer ordinaire. (auteur)

  20. Risk-informed decision making in the nuclear industry: Application and effectiveness comparison of different genetic algorithm techniques

    International Nuclear Information System (INIS)

    Gjorgiev, Blaže; Kančev, Duško; Čepin, Marko

    2012-01-01

    Highlights: ► Multi-objective optimization of STI based on risk-informed decision making. ► Four different genetic algorithms (GAs) techniques are used as optimization tool. ► Advantages/disadvantages among the four different GAs applied are emphasized. - Abstract: The risk-informed decision making (RIDM) process, where insights gained from the probabilistic safety assessment are contemplated together with other engineering insights, is gaining an ever-increasing attention in the process industries. Increasing safety systems availability by applying RIDM is one of the prime goals for the authorities operating with nuclear power plants. Additionally, equipment ageing is gradually becoming a major concern in the process industries and especially in the nuclear industry, since more and more safety-related components are approaching or are already in their wear-out phase. A significant difficulty regarding the consideration of ageing effects on equipment (un)availability is the immense uncertainty the available equipment ageing data are associated to. This paper presents an approach for safety system unavailability reduction by optimizing the related test and maintenance schedule suggested by the technical specifications in the nuclear industry. Given the RIDM philosophy, two additional insights, i.e. ageing data uncertainty and test and maintenance costs, are considered along with unavailability insights gained from the probabilistic safety assessment for a selected standard safety system. In that sense, an approach for multi-objective optimization of the equipment surveillance test interval is proposed herein. Three different objective functions related to each one of the three different insights discussed above comprise the multi-objective nature of the optimization process. Genetic algorithm technique is utilized as an optimization tool. Four different types of genetic algorithms are utilized and consequently comparative analysis is conducted given the

  1. Compaction of bentonite blocks. Development of technique for industrial production of blocks which are manageable by man

    Energy Technology Data Exchange (ETDEWEB)

    Johannesson, L E; Boergesson, L; Sanden, T [Clay Technology AB, Lund (Sweden)

    1995-04-01

    In this report a useful technique for producing compacted blocks of bentonite is described. The report only deals with the technique to produce uniaxially compacted blocks (weight of the blocks: 10-15 kg) which are manageable by man. Tests for producing blocks with a weight of approximately 10 kg were carried out at Hoeganaes Bjuf AB in Bjuf. This industry is normally producing refractory bricks and other refractory products. The plant has facilities for handling large volumes of clay. Furthermore there are machines suitable for producing uniaxially compacted blocks. Performed tests at the plant show that it is possible to compact blocks with good quality. Best quality was reached with a coarsely ground bentonite at a water ratio of 20 %. The compaction was performed with lubricated form and stepwise loading. The tests at Hoeganaes Bjuf AB were preceded by tests in the laboratory. In these tests smaller samples were compacted for studying how different factors affect the quality of the samples (density, water ratio, homogeneity et cetera). The influence of following factors was studied: water ratio of bentonite; bentonite type and granulometry; compaction pressure; compaction rate; form geometry; form lubrication; form heating. The results from these tests were used to modify and optimize the technique in the factory.

  2. Possibilities and limits of digital industrial radiology: the new high contrast sensitivity technique - Examples and system theoretical analysis

    International Nuclear Information System (INIS)

    Zscherpel, U.; Ewert, U.; Bavendiek, K.

    2007-01-01

    During the last years more and more reports about film replacement techniques are published using different ways to prove the required and obtained image quality. The motivation is usually cost reduction due to shorter exposure times and lower storage costs, smaller space requirements and elimination of chemical processing inclusive associated waste handling and disposal. There are no other publications known, which explore the upper limits of image quality achievable by the new digital techniques. This is important for inspection of safety relevant and high risk parts, as e.g. in nuclear or aerospace industries. A new calibration and measurement procedure for digital detector arrays (DDA) was explored to obtain the maximum signal/noise ratio achievable with DDAs. This procedure yields a contrast sensitivity which allows distinguishing wall thickness changes of up to 1/1000 of the penetrated material thickness. Standard film radiography using NDT film systems (with and without lead screens) achieves a wall thickness contrast which is not better than 1/100 even with the best film system class (class 'C1' according to EN 584-1 or 'special' according to ASTM E 1815). Computed Radiography (CR) using phosphor imaging plates is a true film replacement technique without enhancement of the image quality compared to NDT film systems. The comparison is based on parameter studies which measure signal/noise ratios and determine the basic spatial resolution as well as a comparison of radiological images with fine flaws. (authors)

  3. Utilisation de la DSC pour la caractérisation de la stabilité des émulsions eau dans pétrole Use of the Dsc Technique to Characterize Water-In-Crude Oil Emulsions Stability

    Directory of Open Access Journals (Sweden)

    Dalmazzone C.

    2006-12-01

    Full Text Available La technique DSC (Differential Scanning Calorimetry a été appliquée à l'étude des émulsions eau dans pétrole, qui se forment naturellement après un déversement de pétrole en mer. Ces émulsions, également appelées mousses au chocolat , peuvent contenir de 50 à 80% d'eau et se présentent souvent sous la forme d'un produit visqueux, difficile à récupérer mécaniquement, à traiter ou à brûler. Il est par conséquent important de pouvoir estimer leur stabilité pour optimiser le choix du traitement. Un grand nombre de techniques, généralement fondées sur l'analyse de la distribution de tailles de gouttes, peuvent être utilisées pour estimer la stabilité d'une émulsion. Malheureusement, la plupart ne sont pas adaptées à l'étude des émulsions eau dans huile opaques. La méthode la plus utilisée pour caractériser la stabilité de ce type d'émulsions est le bottle test. Elle consiste à mesurer la séparation de phases en fonction du temps. Ce test est la source d'une quantité d'informations appréciables quant à la stabilité de l'émulsion et à la qualité de la phase aqueuse séparée, mais il reste très empirique. La technique DSC est généralement utilisée pour déterminer la composition des émulsions eau dans huile, car elle permet de distinguer l'eau libre de l'eau émulsifiée. Cette étude a montré qu'il s'agit d'une technique très utile qui permet à la fois l'étude de l'évolution de la taille des gouttes dans l'émulsion, et une détermination précise de la quantité d'eau. The DSC technique (Differential Scanning Calorimetry was applied to the study of water-in-crude oil emulsions, which naturally form after an oil spill. The resulting emulsions contain between 50 and 80% seawater and they are often heavy materials, hard to recover mechanically, treat or burn. It is therefore important to assess their stability in order to optimize their treatments. A great variety of techniques are available for

  4. La cartog ra ph ie des inc iden ce s

    International Development Research Centre (IDRC) Digital Library (Canada)

    IDRC CRDI

    che d'ingénierie des incidences à la recherche pour le développe- ment. .... çoivent des stratégies visant à les doter des outils, techniques et ressources utiles pour contribuer au développement. Axer le ... Comment ? La première phase, la définition des intentions, aide le programme à en arriver à un consensus sur les.

  5. Development Of 12 Head GAMMA Detection And Graphical Presentation Software Suitable For Industrial Process Investigation By Radiotracer Technique

    International Nuclear Information System (INIS)

    Saengchantr, Dhanaj; Chueinta, Siripone

    2009-07-01

    Full text: Data logging with prompt graphical presentation software accommodating gamma radiation signals from 12 scintillation detectors through standard RS-232 interface has been developed. Laboratory testing by detection of injected-mixed radioactive tracer in a fluid flowing inside a pipe was conducted. The radioactive mixed fluid passed through the detectors located at several points along the pipe and the generated signals correspond to the mass flow inside the pipe were recorded. Up to 10,000 data points of fast (20 millisecond) dwell time could be accumulated. Graphical presentation allowed fast interpretation while the output data were suitable for more accurate evaluation with standard software e.g. Residence Time Distribution (RTD), Computed Tomography Visualization. Further utilization in the industry, in conjunction with radiotracer techniques, for troubleshooting and process optimization will be further carried out

  6. Using the Continuum of Design Modelling Techniques to Aid the Development of CAD Modeling Skills in First Year Industrial Design Students

    Science.gov (United States)

    Storer, I. J.; Campbell, R. I.

    2012-01-01

    Industrial Designers need to understand and command a number of modelling techniques to communicate their ideas to themselves and others. Verbal explanations, sketches, engineering drawings, computer aided design (CAD) models and physical prototypes are the most commonly used communication techniques. Within design, unlike some disciplines,…

  7. Des vaccins à dose unique à la rescousse du bétail et des moyens ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    L'industrie de l'élevage est une industrie essentielle en Afrique, mais qui subit de grandes pertes en raison d'infections virales évitables. Ce projet vise à mettre un frein au problème. Les chercheurs mettront au point des vaccins prototypes, effectueront des tests sur le terrain et prendront les premières mesures pour ...

  8. Gouvernance et régulation de l'industrie des hydrocarbures venezueliens : une analyse des relations Etat-sociétés pétrolières

    OpenAIRE

    Benhassine, Achraf

    2008-01-01

    Oil is an extremely desired strategic resource which is in the center of the cooperation, the tensions and the conflicts between the producing States and the consumers, between the owners of deposits and oil companies and also between oil companies and consumers. The preoccupation of the political economy is exactly to report the interweaving of the economicand political factors in the formation and in the evolution of the structures of the national petroleum industries. Any change concerning...

  9. LES STRATÉGIES DES PETITES ENTREPRISES DANS LES INDUSTRIES EN CRISE : Une étude des caves particulières de la région vitivinicole du Languedoc-Roussillon

    OpenAIRE

    Duquesnois , Franck

    2011-01-01

    " Here, wine growers hide themselves to die... " said the president of the Agricultural Chamber of Languedoc-Roussillon. This research work focuses on the strategic choices and competitive behaviors of (very) small firms investigated in the crisis situation of Languedoc-Roussillon wine industry in France. First we should state that very few existing research attempt to identify the strategies applied by small firms in a crisis context characterized as times of resources scarcity and a major d...

  10. AGARD Flight Test Techniques Series. Volume 9. Aircraft Exterior Noise Measurement and Analysis Techniques. (Le Bruit a l’Exterieur des Aeronefs: Techniques de Mesure et d’Analyse)

    Science.gov (United States)

    1991-04-01

    sugeseed to me to write ui AGARDograpit on A~rlmaft Noie Mms dsurnent Anallysis Techniques’. Being overjoyed, and quite honoured. I realdily agreed to his...Gelt& I )nd Delta 2 terms) Wb) Source Noise Correction - Jet Engine Noise ’) ielts 3 term) (c) Snor"e Noise Correction - Propeller Noise (Delta 3...printed out, since it is impractical to write these down by hand durilg th,. test). One track on each tape-recorder must be used to record a time code

  11. Market success proves the efficiency of directives in the gas industry in the Federal Republic of Germany; Markterfolg belegt Effizienz des gaswirtschaftlichen Ordnungsrahmens in der Bundesrepublik Deutschland

    Energy Technology Data Exchange (ETDEWEB)

    Weyand, M

    1994-09-01

    Deregulation is the catchword which has been ruling the present debate about energy-economy regulations in the Federal Republic of Germany. Deregulation can be interpreted at least in two ways: 1. Maintenance of existing regulations but modification of regulations which are part of the energy economy laws, 2. Introduction of a compulsory gas transit regulation for the benefit of third parties, compulsory deconcentration of the utilities, and abrogation or change of basic legal conditions. Both approaches are discussed and evaluated. (HW) [Deutsch] Die jetzige Diskussion ueber den energiewirtschaftlichen Ordnungsrahmen in der BRD ist durch das Schlagwort Deregulierung gepraegt. Hierfuer existieren jedoch mindestens zwei verschiedene Interpretationen: 1. Grundsaetzliche Beibehaltung des bestehenden Ordnungsrahmens bei gleichzeitiger Modifizierung von Regelungen im Energiewirtschaftsgesetz; 2. Einfuehrung einer Zwangsdurchleitung zugunsten Dritter, Zwangsentflechtung der Versorgungsunternehmen sowie Abschaffung bzw. Aenderung grundlegender ordnungsrechtlicher Rahmenbedingungen. Der vorliegende Beitrag versucht eine kritische Auseinandersetzung mit den beiden Ansaetzen. (HW)

  12. Non-Cooperative Air Target Identification Using Radar (l’Identification radar des cibles aeriennes non cooperatives)

    Science.gov (United States)

    1998-11-01

    des techniques tr~s prometteuse pour la detection longue port~e. Les progr~s escompt ~s dans le domaine des techniques radar devraient amener des...cibles fixes, des cibles mobiles ou du fouillis de sol. Sa vocation Le moyen de mesures comprend un radar premiere est d’enrichir les banques de donn6es

  13. Evaluation des conditions de germination des noyaux de Grewia ...

    African Journals Online (AJOL)

    personnel

    31 janv. 2014 ... 1Laboratoire de Physiologie et Production Végétales, Université Marien NGOUABI,. Faculté des Sciences et Techniques, BP.69. Brazzaville, Republique du Congo. 2Ecole Nationale Supérieure d'Agronomie et Forestérie, Université Marien NGOUABI,. BP. 69. Brazzaville, Republique du Congo.

  14. L'amélioration des techniques de transformation du manioc en cossettes en RCA : rouissage en vase clos et séchage en encage thermique

    OpenAIRE

    Rasoanantoandro-Gothard , Marie Céline

    2003-01-01

    International audience; Le manioc constitue l'aliment de base en République centrafricaine (RCA). La population le consomme sous diverses formes: tubercule sans préparation (consommé cuit), chickouangue, bouillie, soupe, grillé ou braisé (roui ou non roui), sous forme de pâte cuite préparée à partir de la farine de cossettes. Plus de 80% de la population centrafricaine consomme le manioc sous forme de pâte cuite préparée à partir de la farine de cossette et plus de 50% des besoins énergétique...

  15. Extensions of the techniques for the accelerated unspecific isotopic labelling of organic compounds; Applications nouvelles des techniques accelererees du marquage non specifique de composes organiques; Rasprostranenie metodov uskoreniya mecheniya nespetsifichnymi izotopami organicheskikh slozhnykh soedinenij; Nuevas aplicaciones de las tecnicas de marcacion inespecifica acelerada de compuestos organicos

    Energy Technology Data Exchange (ETDEWEB)

    Ghanem, N A [National Research Centre, El-Dokki, Cairo (Egypt); Westermark, T [Division of Physical Chemistry, Royal Institute of Technology, Stockholm 70 (Sweden)

    1962-03-15

    The paper aims at reviewing new means of obtaining acceleration in the reaction of a radioactive gas with a target material to be labelled and examples of successful cases. The techniques include the use of microwave and radiowave discharges, glow discharges affected through DC or AC sources, and simply ultraviolet radiation. Specific activities of more than 100 mc/g in purified significant quantities of products were obtained. Periods of exposure to discharge were of the order of one minute and decomposition was limited in most cases. Calculations of utilization of the energy absorbed during the labelling process were compared with the energy from ionizing radiation used by Wilzbach and others, and G values for isotope replacement are given. In polystyrene labelling, evidence is found that the mechanisms is governed by an atom-molecule reaction. (author) [French] Les auteurs passent en revue des methodes recentes visant a accelerer la reaction d'un gaz radioactif avec des matieres a marquer; ils citent des cas de reussite. Les techniques etudiees comportent l'emploi de decharges de micro-ondes et d'ondes hertziennes, de decharges luminescentes par des sources de courant continu ou alternatif et de simples rayons ultraviolets. On a obtenu des activites specifiques superieures a 100 mc/g dans des quantites importantes de produits purifies. Les temps d'exposition a la decharge etaient de l'ordre d'une minute; dans la plupart des cas, la decomposition etait limitee. Les auteurs comparent la quantite d'energie absorbee au cours du marquage a celle qui est necessaire lorsqu'on emploie des rayonnements ionisants, comme l'ont fait Wilzbach et autres; ils donnent les valeurs G de remplacement des isotopes. Dans le marquage du polystyrene, il semble bien que le processus soit regi par une reaction atome-molecule. (author) [Spanish] El objeto de la memoria es pasar revista a nuevos metodos para acelerar la reaccion de un gas radiactivo con el material de blanco que se desea

  16. Contribution of the radioactive tracer techniques to the littoral management

    International Nuclear Information System (INIS)

    Alami, R.

    1994-01-01

    The construction of a harbor or its extending, the management of entrance channels and their maintenance (e.g. dredging works), the littoral development for industrial or tourist purposes, the management of urban or industrial rejects are very expensive and have a great impact on the environment, the optimization of which requires to begin with understanding and making sure of the sedimentary mechanisms occurring under the natural conditions. The tracer techniques are, in such cases, a precious tool and a unique help to the decision makers. The profits made by using such techniques in Morocco, which is a seaboard country, have led the C entre National de l'Energie, des Sciences et des Techniques Nucleaires (CNESTEN) to set up a unit which is operational in this field. 7 figs., 8 refs (F.M.)

  17. ANALYSE DES PERCEPTIONS LOCALES ET DES FACTEURS ...

    African Journals Online (AJOL)

    AISA

    1Faculté des Sciences Agronomiques (FSA), Université d'Abomey-Calavi (UAC), 01 BP 526 Cotonou Bénin. Email : cgbemavo@yahoo.fr. 2Institut National des Recherches Agricoles du Bénin, Centre de Recherches Agricoles d'Agonkanmey (CRA-A),. Laboratoire des Sciences du Sol, Eau et Environnement (LSSEE).

  18. Traitement des diagraphies acoustiques. Première partie : application de techniques issues de l'intelligence artificielle au pointe des diagraphies acoustiques Full Waveform Acoustic Data Processing. Part One: an Artificial Intelligence Approach for the Picking of Waves on Full-Waveform Acoustic Data

    Directory of Open Access Journals (Sweden)

    Mari J. L.

    2006-11-01

    Full Text Available Les enregistrements des données acoustiques en champ total (fuit waveform ont conduit le géophysicien et le diagraphiste à utiliser des techniques de traitement du signal pour séparer les différentes ondes observées sur les enregistrements. L'une des tâches importantes du traitement des diagraphies acoustiques est le pointé des temps d'arrivée des différentes ondes enregistrées. Une démarche de type système expert a été utilisée pour mettre au point un algorithme multicanaux qui réalise le pointé des différentes ondes, à l'aide de règles faisant intervenir les caractéristiques ou attributs de chaque onde. Une onde est caractérisée par sa vitesse, sa fréquence, son amplitude et sa cohérence latérale. L'algorithme fournit un ensemble de logs accompagnés d'une estimation de la dispersion des mesures à chaque cote profondeur. Les logs fournis sont les logs de lenteur et les logs de fréquence. Les résultats obtenus sur un ensemble de diagraphies acoustiques enregistrées dans un puits vertical du Bassin parisien montrent que la dispersion des mesures reste faible en comparaison des pas d'échantillonnage en temps et profondeur. Les logs de dispersion peuvent aussi permettre de détecter des phénomènes physiques tels que caves, fractures, conversions d'ondes ou interférences, reliés à la lithologie. Dans une deuxième partie, nous montrerons différentes techniques de séparation d'ondes. La troisième partie illustrera, sur un cas particulier, l'utilisation des logs issus des diagraphies acoustiques pour caractériser les formations. The full waveforms recorded by an array of recievers in a borehole sonic tool contain a set of waves that can be fruitfully used to obtain detailed information about the nearborehole lithology and structure. The different waves that can be observed by full-waveform sonic data are described in this article. The main tools used in the recording of full-waveform data are then reviewed

  19. Study of the texture of porous solids using a technique of {gamma} ray absorption; Application de l'absorption du rayonnement {gamma} a l'etude de la texture des solides poreux

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, M. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-01-01

    avec une erreur maximale {delta}{rho} {<=} 0,005 g/cm{sup 3}. La porosite ouverte a ete evaluee par la methode d'absorption apres impregnation au bromoforme. Un nouveau porosimetre au mercure a ete realise en utilisant la sonde d'absorption pour la mesure du mercure infiltre dans l'echantillon poreux. Grace au caractere localise de l'exploration on etudie, par cette technique, les variations de texture poreuse dans un echantillon heterogene. Utilise comme porosimetre classique dans le cas d'echantillons homogenes, cet appareil est capable d'explorer des diametres equivalents de pores compris entre 500 et 0,14 {mu} avec une erreur maximale, {delta}P {<=} 0,002. La possibilite d'exploration d'echantillons heterogenes jointe a la facilite de determination des porosites dues aux macropores et au caractere non limitatif de la methode dans le domaine des hautes pressions, differencient cet appareil de tous les porosimetres de conception anterieure. On presente des exemples d'utilisation de cette technique dans les cas de reactions graphite-gaz. (auteur)

  20. Study of the texture of porous solids using a technique of {gamma} ray absorption; Application de l'absorption du rayonnement {gamma} a l'etude de la texture des solides poreux

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, M [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-01-01

    {delta}{rho} {<=} 0,005 g/cm{sup 3}. La porosite ouverte a ete evaluee par la methode d'absorption apres impregnation au bromoforme. Un nouveau porosimetre au mercure a ete realise en utilisant la sonde d'absorption pour la mesure du mercure infiltre dans l'echantillon poreux. Grace au caractere localise de l'exploration on etudie, par cette technique, les variations de texture poreuse dans un echantillon heterogene. Utilise comme porosimetre classique dans le cas d'echantillons homogenes, cet appareil est capable d'explorer des diametres equivalents de pores compris entre 500 et 0,14 {mu} avec une erreur maximale, {delta}P {<=} 0,002. La possibilite d'exploration d'echantillons heterogenes jointe a la facilite de determination des porosites dues aux macropores et au caractere non limitatif de la methode dans le domaine des hautes pressions, differencient cet appareil de tous les porosimetres de conception anterieure. On presente des exemples d'utilisation de cette technique dans les cas de reactions graphite-gaz. (auteur)

  1. Report on the actions fostering renewable energy sources; Bilan des actions conduites par Christian Pierret, Secretaire d'Etat a l'Industrie en faveur du developpement des energies renouvelables

    Energy Technology Data Exchange (ETDEWEB)

    Pierret, Christian [State Secretary for Industry, French Government, Paris (France)

    1999-06-15

    The principal renewable energy source of France is, after hydro-power, the wood fuels, the 9.1 Mtep production rate of which exceeds the cumulated coal, gas and oil national productions. The plan 'Wood-energy and Local Development', launched in 1994, resulting in the installation of 168 boilers at a 150 MW total power and consuming 36,000 tep/y, was followed by the plan 'Wood-Wastes', announced by Christian Pierret on February 1998, aiming at boosting the energetic use of wood wastes. In the wind power sector a program EOLE 2005 was launched having as goal installing in France up to 2005 a wind power capacity of 250 to 500 MW. 20 projects with a total capacity of 77.5 MW were selected. Under EOLE 2005 provisions there is a 125.3 MW wind power capacity to be installed up to the end of year 2000. A new call for propositions aiming at up to 100 MW wind power capacity was asked from EDF by the secretary of state Mr Christian Pierret. In the field of thermal solar energy a program titled '20,000 solar boilers in the overseas territories (DOM)' has as objective the installation in 5 years of 20,000 solar boilers in the Antilles, Guiana and Reunion. These means of generating sanitary hot water are actually well-fitted to the climate of these regions where the cost of competing electricity is rather high. By January 1999 almost 15,000 solar boilers were installed in the frame of this program. The large scale production of these units resulted already in a 30% decrease in their price. A new 30 MF/yr program HELIOS 2006 was initiated to boost the development of the solar boilers. Since 1995, under the frame of 'Fonds d'Amortissement des charges d'Electrification' (FACE), a 100 MF project was launched to finance actions of energy management and promote decentralized installations for electricity production from renewable energy sources. These efforts are aimed at fulfilling the electricity needs of isolated sites. By the end

  2. Materials of All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection; Materialy Krajowego Sympozjum Technika Jadrowa w Przemysle, Medycynie, Rolnictwie i Ochronie Srodowiska

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The All-Polish Symposium Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection is cyclic (in 3 year period) conference being a broad review of state of art and development of all nuclear branches cooperated with industry and other branches of national economy and public life in Poland. The conference has been divided in one plenary session and 8 problem sessions as follow: Radiation technologies of flue gas purification; radiation technologies in food and cosmetic industry; application of nuclear techniques in environmental studies and earth science; radiometric methods in material engineering; isotope tracers in biological studies and medical diagnostics; radiometric industrial measuring systems; radiation detectors and device; nuclear methods in cultural objects examination. The poster section as well as small exhibition have been also organised.

  3. Agent des projets et des partenariats (h/f) | CRDI - Centre de ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Gestion de projets. L'agent(e) : fournit un encadrement technique, notamment en analysant les rapports d'étape, en participant à des ateliers, en effectuant des recherches ... travaille et contribue à l'élaboration du plan de travail de la Division et du portefeuille de projets en découlant, au sein de la structure de la DPDA; et.

  4. Analyse de la fiabilité des statistiques des pêcheries maritimes ...

    African Journals Online (AJOL)

    SARAH

    31 janv. 2016 ... SEDZRO Kossi Maxoe¹ *, FIOGBE Emile Didier¹, GUERRA Eduardo Balguerias², STAMATOPOULOS. Constantine³. ¹Laboratoire de Recherche sur les Zones Humides, Faculté des Sciences et des Techniques, Université d'Abomey-. Calavi, 01BP526 Cotonou Bénin, Tél. (229) 95268262. ²Institut Espagnol ...

  5. Vecteurs Singuliers des Theories des Champs Conformes Minimales

    Science.gov (United States)

    Benoit, Louis

    des entiers positifs, p et q etant de meme parite, et p+q= 2. Les vecteurs singuliers | Psi_{p,q}> et |Psi_{m-p,m+2-q} > sont respectivement de poids h _{p,q}+pq/2 et h_ {p,q}+(m-p)(m+2-q)/2.. Les vecteurs singuliers ont une norme nulle et on doit les eliminer des representations pour que celles -ci soient unitaires. Cette elimination engendrent des equations (super-)differentielles qui dependent directement de la forme explicite des vecteurs singuliers et auxquelles doivent obeir les fonctions de correlations de la theorie. Ainsi la connaissance de ces vecteurs singuliers est intimement reliee au calcul des fonctions de correlation. Les equations definissant les vecteurs singuliers forment un systeme lineaire surdetermine dont le nombre d'equations est de l'ordre de N(pq), le nombre de partitions de l'entier pq. Puisque les vecteurs singuliers jouent un role capital en theorie conforme, il est naturel de chercher des formes explicites pour les vecteurs (ou pour des familles infinies de ceux -ci). Nous donnons ici la forme explicite pour la famille infinie de vecteurs singuliers ayant un de ses indices egal a 1, pour les algebres de Virasoro et de Neveu-Schwarz. Depuis ces decouvertes, d'autres techniques de construction des vecteurs singuliers ont ete developpees, dont celle de Bauer, Di Francesco, Itzykson et Zuber pour l'algebre de Virasoro qui reproduit directement l'expression explicite des vecteurs singuliers |Psi _{1,q}> et |Psi_{p,1}>. Ils ont utilise l'algebre des produits d'operateurs et la fusion entre representations irreductibles pour engendrer des relations de recurence produisant les vecteurs singuliers. Dans le dernier chapitre de cette these nous adaptons cet algorithme a la construction des vecteurs singuliers de l'algebre de Neveu-Schwarz.

  6. Databases in the documentation management for big industrial projects; Les bases de donnees dans la gestion documentaire des grands projets industriels

    Energy Technology Data Exchange (ETDEWEB)

    Cauchet, A; Chevillard, F; Parisot, Y; Tirefort, C [Societe EURODOC, Saint Quentin en Yvenlines (France)

    1990-05-01

    The documentation management of a big industrial project involves a continuous update of information, both in the study and realization phase or in the operation phase. The organization of the technical documentation for big industrial projects requests complex information systems. In the first part of this paper are presented the methods appropriate for the analysis of documentation management procedures and in the second part are presented the tools by the combination of which a documentation system for the user is provided. The case of the documentation centres for the Hague reprocessing plant is described.

  7. Technique and radiation dose of conventional X-rays and computed tomography of the sacroiliac joint; Technik und Strahlendosis konventioneller Roentgenaufnahmen und Computertomographie des Sakroiliakalgelenks

    Energy Technology Data Exchange (ETDEWEB)

    Jurik, A.G. [Department of Radiology R, Aarhus Kommunehospital (Denmark)

    2004-03-01

    Anterior-posterior (a.p.) or posterior-anterior X-rays of the sacroiliac joint, sometimes supplemented by a transverse view, have been the method of choice for diagnosis of patients suspected of having sacroiliitis. The sensitivity and specificity of conventional X-rays are relatively low, which can delay the diagnosis of sacroiliitis. Computed tomography (CT) is superior to conventional X-rays for diagnosis of sacroiliitis, but does emit a relatively higher dose of radiation. For this reason, particularly for females, CT should be optimized by employing semi-coronal planes, which require a lower radiation dose than axial planes. CT in a semi-coronal plane causes minimal radiation to the ovaries, and the effective radiation dose for women might even be lower than with conventional AP X-rays. Therefore, for suspected sacroiliitis in young women, CT in the semi-coronal plane is the preferred imaging method with respect to diagnostics and radiation protection when magnetic resonance imaging (MRI) is not available. Male gonads can be protected from radiation doses in conventional X-rays, and CT as the primary imaging method can only be justified in these cases because of its better diagnostic capabilities. Due to the lack of inherent risk factors, MRI is superior to CT for diagnostics since it provides images of inflammatory signs in addition to joint destruction. Thus, when available, MRI should be given preference for diagnosis of sacroiliitis. (orig.) [German] Roentgenaufnahmen des Sakroiliakalgelenks im anterior-posterioren bzw. posterior-anterioren Strahlengang, gelegentlich ergaenzt durch die Schraegaufnahme, sind seit vielen Jahren die Methode der Wahl fuer die Diagnostik bei Patienten mit Verdacht auf Sakroiliitis. Die Sensitivitaet und Spezifitaet des konventionellen Roentgens sind relativ niedrig, was die Diagnose der Sakroiliitis verzoegern koennte. Die Computertomographie (CT) ist dem konventionellen Roentgen fuer die Diagnostik der Sakroiliitis ueberlegen

  8. The use aeroplanes and vehicles for prospecting. The technique of the detection radioactivity. The future opened up by the use of the discrimination of energies; Methodes de prospection autoportee et aeroportee. La technique de la detection des rayonnements. Les perspectives offertes par la discrimination des energies

    Energy Technology Data Exchange (ETDEWEB)

    Guitton, J; Berbezier, J; Blangy, B; Lallemant, C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    The idea of installing activity detectors on aeroplanes and vehicles has been widely applied by the CEA since the start of prospecting in the arid and tropical regions of the Communaute Francaise. Three systems of detection have been developed and compared in a systematic manner: a group of 50 G.M. tubes; the sodium iodide scintillator; the plastic scintillator. The sodium iodide scintillator is used as a standard reference; the results are compared by graphical recording. Airborne prospecting is carried out in two stages: the initial flights, which follow a kilometre square network, make possible the discovery of the most likely zones; these likely zones are then examined in greater detail using light aeroplanes or helicopters. The two types of airborne scintillation measuring devices which have been developed by the CEA are described in this article. The practical results obtained during systematic and detailed airborne prospecting campaigns in the Hoggar are described. The difficulty in airborne uranium prospecting is to be able to immediately distinguish while in flight, anomalies caused by uranium from those caused by thorium. (author) [French] L'idee de monter des detecteurs de rayonnements sur des avions ou des vehicules a ete largement appliquee par le CEA des le debut des prospections dans les pays sahariens et tropicaux de la Communaute Fran ise. On a realise et compare d'une maniere systematique trois moyens de detection: groupe de 50 tubes GM; scintillateur d'iodure de sodium, scintillateur plastique. L'appareil de reference sera le scintillateur d'iodure de sodium; les resultats sont compares par enregistrement graphique. La prospection aeroportee se fait en deux etapes; les premiers vols systematiques suivant un quadrillage kilometrique permettent de reperer les zones interessantes; ces dernieres font l'objet d'examens plus detailles effectues en avion leger ou en helicoptere. Dans cet article, on decrit les deux types de scintillometres aeroportes

  9. Determination of sulfur dioxide in ambient air and in industrial stack using X-ray fluorescence technique

    International Nuclear Information System (INIS)

    Sumitra, T.; Chankow, N.; Punnachaiya, S.; Laopaibul, R.

    1988-01-01

    Sulfur dioxide is a major air pollutant of concern. The gas has to be monitored both in ambient air and in industrial stacks. There are several methods of measuring sulfur dioxide. Standard methods adopted for Thailand are based on chemical methods. These are normally sensitive to light and temperature changes. Therefore a method of collecting air sample and determination of SO 2 by X-ray fluorescence technique was developed. Air sampling was done by an in-house low cost air sampler using automobile battery, dependency on a.c. source was thus avoided. The air pump has a flow rate between 0.2-1.5 liters/minute and draw about 0.6 A from a 12 V battery. SO 2 was collected on 37 mm filters impregnated with 5% sodium carbonate. This method could detect SO 2 from 10 μg up. The method has been checked by interlaboratory comparison. Field test has also been performed at some tobacco curing plants in Amphoe Sansai, Changwat Chiengmai, both in ambient air and in stacks. The results were found to be satisfactory and comparable with the standard methods

  10. Optimization of the workers radiation protection in the electro nuclear, industrial and medical fields; Optimisation de la radioprotection des travailleurs dans les domaines electronucleaire, industriel et medical

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    This conference is devoted to the radiation protection and the best way to optimize it. It reviews each area of the nuclear industry, and explores also the medical sector. Dosimetry, ALARA principle and new regulation are important points of this meeting. (N.C.)

  11. The leakage problem in vacuum system. Realization of a mass spectrometer detecting leaks; Le probleme des fuites en technique du vide. Realisation d'un spectrometre de masse detecteur de fuite

    Energy Technology Data Exchange (ETDEWEB)

    Geller, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1954-11-15

    In the first part of this paper we consider the problem of leaks in vacuum systems, and their detection. We consider in particular the method of detection by means of a helium spectrometer. The second part deals with the experimental set p. The analyser and the ion source have been studied in great detail, and we have also discussed the technological and mechanical aspects of the apparatus and its performances. (author) [French] Dans la premiere partie de ce travail, nous traitons le probleme des fuites en technique du vide et leur detection en general. La methode de detection par spectrometre a helium y est envisagee plus particulierement. La deuxieme partie de l'article est consacree a la realisation du spectrometre. Le tube analyseur et la source d'ions y sont etudies en detail. Nous exposons de meme les conceptions technologiques et mecaniques de l'appareil ainsi que ses performances. (auteur)

  12. MODELISATION DE LA CINETIQUE CHIMIQUE DANS LA REDUCTION DES OXYDES D4AZOTE PAR DECHARGE COURONNE.

    OpenAIRE

    MEDJAHDI, Sarah ines

    2015-01-01

    CE TRAVAIL DE recherche rentre dans le cadre général de modélisation de la réduction des oxydes d'azote . l'utilisation des réacteurs a plasma froid non-thermique généré par des décharges couronnes est actuellement l'une des techniques les puis promettre .ses pour la destruction des oxydes d'azote .en effet , le traitement des gaz pollués par les décharges couronnes est notamment rendu possible par la multiplication des décharges Électriques .

  13. Study of the degradation mechanisms of amines used for the capture of CO{sub 2} in industrial fumes; Etude des mecanismes de degradation des amines utilisees pour le captage du CO{sub 2} dans les fumees

    Energy Technology Data Exchange (ETDEWEB)

    Lepaumier, H

    2008-10-15

    Global warming leads to reduce greenhouse gas emissions. Post combustion CO{sub 2} capture with solvent is the most advanced technology to reduce CO{sub 2} emissions in industrial fumes. A major problem associated with chemical absorption of CO{sub 2} using the benchmark ethanolamine (MEA) is solvent degradation through irreversible side reactions with CO{sub 2} and O{sub 2} which leads to numerous harmful impacts to the process: corrosion, solvent loss, foaming, fouling, and viscosity increase. So, developing new amines with higher chemical stability is essential. This work is based on the chemical stability study of 17 different molecules. Their structures have been chosen in order to establish structure-property relationships: alkanolamines, known for gas treatment application (MEA, DEA, MDEA, AMP...), di-amines, and tri-amines without alcohol function. Impact of temperature, CO{sub 2}, and O{sub 2} on degradation has been studied. Strong experimental conditions have been used to observe significant degradation after a 15 days experiment. Separation, identification and quantification of degradation products have been performed by using different testing instructions such as gas chromatography, mass spectrometry, ionic chromatography and NMR. Different mechanisms are proposed to explain most of degradation compounds. Radical reactions (dealkylation, alkylation, ring-closure reactions and piperazinones formation) are involved under O{sub 2} pressure whereas CO{sub 2} induces ionic reactions (dealkylation, alkylation, addition, ring-closure reactions and oxazolidinones or imidazolidinones formation). Large discrepancies of stability are noticed among the different amines. Knowledge of degradation products and reaction mechanisms has thus permitted to establish some relationships between structure and chemical stability: for example, role of the amine function (primary, secondary, tertiary), impact of alkyl chain length between the two amino groups and steric

  14. Quality of electricity service: Evaluation of nuisance index (IGI) of industrial customers; Qualite du service electrique:evaluation de l`indice de gene individuel des clients industriels

    Energy Technology Data Exchange (ETDEWEB)

    Naggar, R. [Hydro-Quebec, Montreal, PQ (Canada)

    1996-08-01

    The effects of power interruption on individual industrial customers by computing an individual nuisance index (IGI) is one of the tools planned by Hydro-Quebec to measure quality of service to its customers. When fully functioning, IGI will represent a combined value of loss of sales, overtime, lost materials and other direct costs, each IGI tailor-made for a particular company. Data for computing the index will be obtained from Hydro-Quebec`s own customer classification database, plus a commercial technical database (DTC) containing data required for the assessment of the nuisance, and a survey carried out by Hydro-Quebec involving some 1600 industrial customers. As of this date, the DTC is not yet available. A statistical analysis of survey responses was substituted to provide default values based on available parameters. Hydro-Quebec is confident that this new approach to evaluating service quality will open new horizons in quality assurance. 3 refs., 5 tabs.

  15. French and International experience on the dialogue around industrial sites; Experience francaise et internationales sur la concertation autour des sites industriels

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Th [Centre d' Etude sur l' Evaluation de la Protection dans le Domaine Nucleaire, CEPN, 92 - Fontenay aux Roses (France); Heriard Dubreuil, G; Gadbois, S [Mutadis, 94 - Vitry (France); Oudiz, A [Institut de Radioprotection et de Surete Nucleaire (IRSN), 92 - Clamart (France); Remond Gouilloud, M [Paris-6 Univ. Sorbonne, 75 (France)

    2002-12-15

    This report presents the results of a research work about 'the stakes of the dialogue around the follow up of nuclear and non nuclear industrial installations'. It used the experience of the North Cotentin radioecology group where expertise has been implemented in order to evaluate the impact on health of the releases of the Cogema La Hague plant. This report is the fruit of an interdisciplinary group ( experts of activities with risks, radiation protection, regulation in environment). (N.C.)

  16. Analyse économique de l’industrie photovoltaïque : mondialisation, dynamique des coûts, et politiques publiques

    OpenAIRE

    Du Fayet De La Tour , Arnaud

    2012-01-01

    In the last decade, the photovoltaic market was multiplied by 10, module price was reduced by 60%, and China increased its share in cell and module production from almost nothing to more than half. The purpose of this thesis is to shed light on the mechanisms driving these transformations. We analyse how China managed to acquire the photovoltaic technology, relying on interviews with actors of the Chinese photovoltaic industry, and data gathered on patents related to the photovoltaic technolo...

  17. A contribution from Gaz de France to the economic performance of industries; Contribution de Gaz de France a la perfomance economique des industriels

    Energy Technology Data Exchange (ETDEWEB)

    Depail, J.C. [Gaz de France (GDF), 75 - Paris (France)

    1996-12-31

    The aim of the policy of the French national gas utility, Gaz de France, towards industries, is to promote natural gas as a competitive fuel compared to fuels and electric power, with energy efficient solutions that are easy to implement and maintain: space heating, paint curing, surface cleaning, bath heating, vapour generation, waste treatment (especially for molding sand and volatile organic compounds, sludge drying). Gaz de France proposes also expertise schemes and audits

  18. Subventionierung von erneuerbarer Energie : eine industrieökonomische Analyse des strategischen Wettbewerbs in der Erneuerbaren-Energieindustrie bei unterschiedlichen staatlichen Regulierungen

    OpenAIRE

    Schaller, Markus

    2006-01-01

    In der vorliegenden Arbeit werden ausgewählte Probleme, die im Zusammenhang mit der Subventionierung von erneuerbarer Energien stehen, in finanztheoretischen und industrieökonomischen Modellen formal analysiert. Der erste Teil der Arbeit beschäftigt sich mit der Subventionierung von Demonstrationsprojekten zur Erprobung neuer Technologien der erneuerbaren Energiegewinnung. Die Information, die durch die Erprobung über die wirtschaftliche Leistungsfähigkeit der Technologie generiert wird, ist...

  19. Comparative Ebulliometry: a Simple, Reliable Technique for Accurate Measurement of the Number Average Molecular Weight of Macromolecules. Preliminary Studies on Heavy Crude Fractions Ébulliométrie comparative : technique simple et fiable pour déterminer précisément la masse molaire moyenne en nombre des macromolécules. Etudes préliminaires sur des fractions lourdes de bruts

    Directory of Open Access Journals (Sweden)

    Behar E.

    2006-12-01

    Full Text Available This article is divided into two parts. In the first part, the authors present a comparison of the major techniques for the measurement of the molecular weight of macromolecules. The bibliographic results are gathered in several tables. In the second part, a comparative ebulliometer for the measurement of the number average molecular weight (Mn of heavy crude oil fractions is described. The high efficiency of the apparatus is demonstrated with a preliminary study of atmospheric distillation residues and resins. The measurement of molecular weights up to 2000 g/mol is possible in less than 4 hours with an uncertainty of about 2%. Cet article comprend deux parties. Dans la première, les auteurs présentent une comparaison entre les principales techniques de détermination de la masse molaire de macromolécules. Les résultats de l'étude bibliographique sont rassemblés dans plusieurs tableaux. La seconde partie décrit un ébulliomètre comparatif conçu pour la mesure de la masse molaire moyenne en nombre (Mn des fractions lourdes des bruts. Une illustration de l'efficacité de cet appareil est indiquée avec l'étude préliminaire de résidus de distillation atmosphérique et de résines. En particulier, la mesure de masses molaires pouvant atteindre 2000 g/mol est possible en moins de 4 heures avec une incertitude expérimentale de l'ordre de 2 %.

  20. Evolution of nuclear chemical industry in France; Evolution de l'industrie chimique nucleaire en France

    Energy Technology Data Exchange (ETDEWEB)

    Fould, M H [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    'impulsion du CEA, mais aussi de maitres d'oeuvres tels qu'Electricite de France et la Marine Marchande, l'effort nucleaire fran is atteint pour les annees 1957-1961, environ 600 milliards de francs: plus de la moitie de cette somme sera depensee par l'industrie chimique en recherches, installations pilotes, constructions d'usines et livraisons. Faire bien, vite et rentable sont les buts recherches. Ces objectifs sont atteints grace a une collaboration intime des grands services de l'etat et de l'industrie privee. Ce gros effort s'exerce principalement dans les voies suivantes: - Un traitement chimique pousse de tonnages croissants des minerais de l'Union fran ise, visant a produire un uranium pur, abondant et bon marche. - Une preparation soigneuse de combustibles nucleaires economiques et parfaitement adaptes aux divers types de reacteurs en fonctionnement ou en construction. - Un retraitement des combustibles irradies pour en extraire le plutonium de facon complete ainsi que l'uranium et certains produits de fission. - Une fabrication industrielle des materiaux nucleairement purs ou resistants a la corrosion exiges par la technologie des reacteurs producteurs d'energie et de recherches. - La fourniture aux multiples utilisateurs etrangers et fran is d'isotopes et de traceurs radioactifs reclames par la medecine, l'industrie et l'agriculture en nombre toujours croissant. - Un traitement chimique meticuleux des effluents gazeux ou liquides dans des stations au controle rigoureux afin de rendre les reacteurs et leurs annexes parfaitement surs d'emploi. Cet expose aura montre l'ampleur de l'effort deploye par une industrie chimique nucleaire jeune, dynamique et en plein essor. Ayant assure ses techniques, realise de nombreuses installations, elle est largement en etat de faire face au programme atomique fran is. En outre, elle est capable et desireuse d'etre associee aux developpements de l'industrie atomique etrangere notamment dans te cadre de l'Euratom et d

  1. Potential application of quantitative microbiological risk assessment techniques to an aseptic-UHT process in the food industry.

    Science.gov (United States)

    Pujol, Laure; Albert, Isabelle; Johnson, Nicholas Brian; Membré, Jeanne-Marie

    2013-04-01

    Aseptic ultra-high-temperature (UHT)-type processed food products (e.g., milk or soup) are ready to eat products which are consumed extensively globally due to a combination of their comparative high quality and long shelf life, with no cold chain or other preservation requirements. Due to the inherent microbial vulnerability of aseptic-UHT product formulations, the safety and stability-related performance objectives (POs) required at the end of the manufacturing process are the most demanding found in the food industry. The key determinants to achieving sterility, and which also differentiates aseptic-UHT from in-pack sterilised products, are the challenges associated with the processes of aseptic filling and sealing. This is a complex process that has traditionally been run using deterministic or empirical process settings. Quantifying the risk of microbial contamination and recontamination along the aseptic-UHT process, using the scientifically based process quantitative microbial risk assessment (QMRA), offers the possibility to improve on the currently tolerable sterility failure rate (i.e., 1 defect per 10,000 units). In addition, benefits of applying QMRA are (i) to implement process settings in a transparent and scientific manner; (ii) to develop a uniform common structure whatever the production line, leading to a harmonisation of these process settings, and; (iii) to bring elements of a cost-benefit analysis of the management measures. The objective of this article is to explore how QMRA techniques and risk management metrics may be applied to aseptic-UHT-type processed food products. In particular, the aseptic-UHT process should benefit from a number of novel mathematical and statistical concepts that have been developed in the field of QMRA. Probabilistic techniques such as Monte Carlo simulation, Bayesian inference and sensitivity analysis, should help in assessing the compliance with safety and stability-related POs set at the end of the manufacturing

  2. Abrasive blasting, a technique for the industrial decontamination of metal components and concrete blocks from decommissioning to unconditional release levels

    International Nuclear Information System (INIS)

    Gills, R.; Lewandowski, P.; Ooms, B.; Reusen, N.; Van Laer, W.; Walthery, R.

    2007-01-01

    When decommissioning nuclear installations, large quantities of metal components are produced as well as significant amounts of other radioactive materials, which mostly show low surface contamination. Having been used or having been brought for a while in a controlled area marks them as 'suspected material'. In view of the very high costs for radioactive waste processing and disposal, alternatives have been considered, and much effort has gone to recycling through decontamination, melting and unconditional release of metals. In a broader context, recycling of materials can considered to be a first order ecological priority in order to limit the quantities of radioactive wastes for final disposal and to reduce the technical and economic problems involved with the management of radioactive wastes. It will help as well to make economic use of primary material and to conserve natural resources of basic material for future generations. In a demonstration programme, Belgoprocess has shown that it is economically interesting to decontaminate metal components to unconditional release levels using dry abrasive blasting techniques, the unit cost for decontamination being only 30 % of the global cost for radioactive waste treatment, conditioning, storage and disposal. As a result, an industrial dry abrasive blasting unit was installed in the Belgoprocess central decontamination infrastructure. At the end of December 2006, more than 1,128 Mg of contaminated metal has been treated as well as 313 Mg of concrete blocks. The paper gives an overview of the experience relating to the decontamination of metal material and concrete blocks at the decommissioning of the Eurochemic reprocessing plant in Dessel, Belgium as well from the decontamination of concrete containers by abrasive blasting. (authors)

  3. The convergence of electric power and natural gas industries. Mergers and acquisitions in the United States; La convergence des industries de l'electricite et du gaz naturel: les fusions-acquisitions aux Etats-Unis

    Energy Technology Data Exchange (ETDEWEB)

    Meritet, S

    2000-07-01

    Deep transformations have taken place in the US electric power industry, in terms of organisation and competition. The reforms of the regulation of this sector have changed the operation rules and, as an answer, the companies have adapted their behaviour. The reorganization is characterized by the combination between new competitive markets with new occupations. The deregulation and the technical progress accelerate the reconfiguration of the industry with the convergence of the natural gas and electric power activities. Since 1996, the numerous mergers-acquisitions between companies are representative of the tight links existing between the two energy sources. In this work, the convergence of the natural gas and power industries in the US is examined. The study of the reconciliation between power and gas companies (mainly the utilities) stresses on the improvement of the combined companies efficiency. The first part deals with the reconfiguration of the US power industry. The second part analyzes the consequences of the gas-electricity mergers and acquisitions. It includes the exploitation of financial data and a classical econometric test about the 'size-scale-spread' relation. The re-composition of the value chain is at the center of the industrial economy problem: it gives the opportunity for new forms of markets and firms. (J.S.)

  4. 75 caracteristiques et evolution des operations de fusions

    African Journals Online (AJOL)

    Elles apparaissent enfin comme un moyen à la disposition des entreprises de grande taille afin de se développer en acquérant des PME. Mots clés : Fusions & Acquisitions, Tunisie, Industrie, Commerce. Classification JEL : L26, G34. *. Chercheur associé au CEPN, Université Paris 13, PRES Sorbonne Paris-Cité,. France.

  5. variabilite des productions et des revenus des exploitations

    African Journals Online (AJOL)

    3Centre de coopération internationale en recherche agronomique pour le développement (CIRAD), UMR Innovation,. Montpellier, France. Doubangolo COULIBALY, Email kone_b@yahoo.fr. RESUME. La durabilité des systèmes de production à base de coton dans un contexte de variabilité des prix aux producteurs et de ...

  6. Ateliers de formation et renforcement des capacités de l'African ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    L'African Network Operators Group (AfNOG) procure aux exploitants et ingénieurs de réseau des universités, des établissements de recherche et des industries ... Studies. Supporting learning and research : content opportunities for academic and research libraries / networks in Africa; presentation at AFREN 3, Rabat, 2008.

  7. Tracking techniques for the method of characteristics applied to the neutron transport problem in multi-dimensional domains; Techniques de tracage pour la methode des caracteristiques appliquee a la resolution de l'equation du transport des neutrons en domaines multi-dimensionnels

    Energy Technology Data Exchange (ETDEWEB)

    Fevotte, F

    2008-10-15

    In the past years, the Method of Characteristics (MOC) has become a popular tool for the numerical solution of the neutron transport equation. Among its most interesting advantages are its good precision over computing time ratio, as well as its ability to accurately describe complicated geometries using non structured meshes. In order to reduce the need for computing resources in the method of characteristics, we propose in this dissertation two lines of improvement. The first axis of development is based on an analysis of the transverse integration technique in the method of characteristics. Various limitations have been discerned in this regard, which we intend to correct by proposing a new variant of the method of characteristics. Through a better treatment of material discontinuities in the geometry, our aim is to increase the accuracy of the transverse integration formula in order to decrease the computing resources without sacrificing the quality of the results. This method has been numerically tested in order to show its interest. Analysing the numerical results obtained with this new method also allows better understanding of the transverse integration approximations. Another improvement comes from the observation that industrial reactor cores exhibit very complex structures, but are often partly composed of a lattice of geometrically identical cells or assemblies. We propose a systematic method taking advantage of repetitions in the geometry to reduce the storage requirements for geometric data. Based on the group theory, this method can be employed for all lattice geometries. We present some numerical results showing the interest of the method in industrial contexts. (author)

  8. X-ray digital industrial radiography (DIR) for local liquid velocity (V{sub LL}) measurement in trickle bed reactors (TBRs): Validation of the technique

    Energy Technology Data Exchange (ETDEWEB)

    Mohd Salleh, Khairul Anuar, E-mail: kmfgf@mst.edu; Lee, Hyoung Koo [Department of Mining and Nuclear Engineering, Missouri University of Science and Technology, Fulton Hall, 310 W. 14th St., Rolla, Missouri 65409 (United States); Rahman, Mohd Fitri Abdul [Department of Chemical and Biochemical Engineering, Missouri University of Science and Technology, 143 Schrenk Hall, 400 W. 11th St., Rolla, Missouri 65409 (United States); Al Dahhan, Muthanna H. [Department of Mining and Nuclear Engineering, Missouri University of Science and Technology, Fulton Hall, 310 W. 14th St., Rolla, Missouri 65409 (United States); Department of Chemical and Biochemical Engineering, Missouri University of Science and Technology, 143 Schrenk Hall, 400 W. 11th St., Rolla, Missouri 65409 (United States)

    2014-06-15

    Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (V{sub LL}) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the V{sub LL} within TBRs.

  9. X-ray digital industrial radiography (DIR) for local liquid velocity (VLL) measurement in trickle bed reactors (TBRs): Validation of the technique

    Science.gov (United States)

    Mohd Salleh, Khairul Anuar; Rahman, Mohd Fitri Abdul; Lee, Hyoung Koo; Al Dahhan, Muthanna H.

    2014-06-01

    Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (VLL) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the VLL within TBRs.

  10. X-ray digital industrial radiography (DIR) for local liquid velocity (VLL) measurement in trickle bed reactors (TBRs): Validation of the technique

    International Nuclear Information System (INIS)

    Mohd Salleh, Khairul Anuar; Lee, Hyoung Koo; Rahman, Mohd Fitri Abdul; Al Dahhan, Muthanna H.

    2014-01-01

    Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (V LL ) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the V LL within TBRs

  11. X-ray digital industrial radiography (DIR) for local liquid velocity (V(LL)) measurement in trickle bed reactors (TBRs): validation of the technique.

    Science.gov (United States)

    Mohd Salleh, Khairul Anuar; Rahman, Mohd Fitri Abdul; Lee, Hyoung Koo; Al Dahhan, Muthanna H

    2014-06-01

    Local liquid velocity measurements in Trickle Bed Reactors (TBRs) are one of the essential components in its hydrodynamic studies. These measurements are used to effectively determine a reactor's operating condition. This study was conducted to validate a newly developed technique that combines Digital Industrial Radiography (DIR) with Particle Tracking Velocimetry (PTV) to measure the Local Liquid Velocity (V(LL)) inside TBRs. Three millimeter-sized Expanded Polystyrene (EPS) beads were used as packing material. Three validation procedures were designed to test the newly developed technique. All procedures and statistical approaches provided strong evidence that the technique can be used to measure the V(LL) within TBRs.

  12. Industrial applications of membrane processes in chemistry and energy generation; Applications industrielles des procedes membranaires en chimie et production d'energie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    The French membranes club (CFM), with the sustain of the French institute of petroleum (IFP) has organized this meeting which aims to present the most recent industrial realizations in the domain of membrane processes in the chemistry and energy generation sectors. This document gathers the abstracts of the presentations: 1 - hydrogen purification and CO{sub 2} extraction: development of polymer matrix and metal nano-particulate hybrid membranes for selective membrane applications; study of silicone-based mixed matrix membranes for hydrogen purification via inverse selectivity principle; CO{sub 2} capture from gaseous effluents for its sequestration: role and limitations of membrane processes; membranes and processes for the abatement of the acid gas content of smokes; new structural model for Nafion{sup R} membranes, the benchmark polymer for low temperature fuel cells; 2 - molecular screen-based membranes: MFI-alumina nano-composite ceramic membranes: preparation and characterization, gaseous transport and separation; characterization and permeation properties of supported MFI membranes; in-situ measurement of butane isomers diffusion in MFI zeolite membranes through transient permeation tests; 3 - vapors separation: stability of silver particulates in PA12-PTMO/AgBF{sub 4} composite membranes and its effect on the easier ethylene transport inside these membranes; 4 - separation of liquid organic mixtures: isomers separation using cyclo-dextrins bearing membranes: application to the extraction and separation of xylene isomers; electrodialysis in organic environment: application to the electro-synthesis; study of polymer materials permeability; 5 - treatment of industrial waters: use of NanoFlux software in the modeling of nano-filtration membrane processes in the chemical industry: elimination of sulfate impurities from 'Chloralkali' brines; ultra-filtration of a wastewater containing partially emulsified oil; efficiency of a hybrid membrane separation

  13. The Party's Over: Oil, War And The Fate Of Industrial Societies; Petrole la fete est finie. Avenir des societes industrielles apres le pic petrolier

    Energy Technology Data Exchange (ETDEWEB)

    Heinberg, R

    2008-07-01

    The world is about to run out of cheap oil and change dramatically. Within the next few years, global production will peak. Thereafter, even if industrial societies begin to switch to alternative energy sources, they will have less net energy each year to do all the work essential to the survival of complex societies. We are entering a new era, as different from the industrial era as the latter was from medieval times. In 'The Party's Over', Richard Heinberg places this momentous transition in historical context, showing how industrialism arose from the harnessing of fossil fuels, how competition to control access to oil shaped the geopolitics of the twentieth century and how contention for dwindling energy resources in the twenty-first century will lead to resource wars in the Middle East, Central Asia and South America. He describes the likely impacts of oil depletion and all of the energy alternatives. Predicting chaos unless the United States-the world's foremost oil consumer-is willing to join with other countries to implement a global program of resource conservation and sharing, he also recommends a 'managed collapse' that might make way for a slower-paced, low-energy, sustainable society in the future. More readable than other accounts of this issue, with fuller discussion of the context, social implications and recommendations for personal, community, national and global action, Heinberg's updated book is a riveting wake-up call for human-kind as the oil era winds down, and a critical tool for understanding and influencing current US foreign policy.

  14. Fire prevention in industrial installations presenting a risk for man and environment (ICPE); La prevention des incendies dans les ICPE: une exigence d'amelioration permanente

    Energy Technology Data Exchange (ETDEWEB)

    Moche, L. [Ministere de l' Amenagement du Territoire et de l' Environnement, Direction de la Prevention des Pollutions et des Risques, 75 - Paris (France)

    2000-09-01

    The most likely accident in industrial installations is fire. 59 out of 100 accidents reported in 1999 describe a fire outbreak, the fire is either the initiating cause of the accident or the form into which the event eventually evolves. This article briefly describes the why and the wherefore of French regulations on fire prevention in installations presenting a risk for man and environment. The French system is based on the responsibility of the plant operator and on the result of inspections performed by authorities to check the conformity of the installation with current regulations. (A.C.)

  15. French and International experience on the dialogue around industrial sites; Experience francaise et internationales sur la concertation autour des sites industriels

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Th. [Centre d' Etude sur l' Evaluation de la Protection dans le Domaine Nucleaire, CEPN, 92 - Fontenay aux Roses (France); Heriard Dubreuil, G.; Gadbois, S. [Mutadis, 94 - Vitry (France); Oudiz, A. [Institut de Radioprotection et de Surete Nucleaire (IRSN), 92 - Clamart (France); Remond Gouilloud, M. [Paris-6 Univ. Sorbonne, 75 (France)

    2002-12-15

    This report presents the results of a research work about 'the stakes of the dialogue around the follow up of nuclear and non nuclear industrial installations'. It used the experience of the North Cotentin radioecology group where expertise has been implemented in order to evaluate the impact on health of the releases of the Cogema La Hague plant. This report is the fruit of an interdisciplinary group ( experts of activities with risks, radiation protection, regulation in environment). (N.C.)

  16. Prevention of the Causes and Consequences of Criticality Accidents: Measures Adopted in France; Prevention des Causes et des Consequences d'un Accident de Criticite: Solutions Adoptees en France

    Energy Technology Data Exchange (ETDEWEB)

    Fruchard, Y.; Lavie, J. -M. [Commissariat a l' Energie Atomique, Paris (France)

    1966-05-15

    It is important to guard against the risk of criticality accidents by seeking to prevent their occurrence through the elimination of their causes and also by taking steps to provide against their consequences. These two aspects are closely linked since the efforts made to elaborate preventive procedures are dictated by the importance of the repercussions which such accidents are liable to have in the human, economic and psychological spheres. The criticality accidents which have occurred in the nuclear industry, though small in number, do reveal the imperfect nature of the techniques adopted to prevent them, and they constitute the only available realistic basis for evaluating their consequences and developing suitable precautionary techniques. The authors give a detailed analysis of the known causes and consequences of past criticality accidents and on this basis make a number of comments in connection with the validity of traditional safety criteria, the probability of accidents for different types of operation, the characteristic accidents capable of serving as models, and the extent of possible radiological consequences. The measures adopted in France to limit the consequences of a possible criticality accident (location, design and lay-out of installations, accident detection dosimetry for exposed personnel) are briefly described after a short account of the criteria used in deciding on them. Finally, the authors discuss the economic implications of adopting particular precautionary measures and of applying them uniformly, taking due account of the question of reliability. (author) [French] II est important de se proteger contre les risques d'accidents de criticite en tentant, d'une part, de prevenir les accidents eux-memes par l'elimination de leurs causes, d'autre part, de parer a leurs consequences. Ces deux aspects sont tres lies: l'effort portant sur la prevention des accidents decoule de l'importance de leurs consequences sur les plans humain, economique

  17. Production of artificial radioelements; Production des radioelements artificiels

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, C [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The techniques used in the production of artificial radioelements are described, with special emphasis on the following points: - nuclear reactions and use of reactors; - chemical separation methods and methods for enriching the activity of preparations; - protection of personnel and handling methods. (author) [French] On decrit l'ensemble des techniques utilisees dans la fabrication des radioelements artificiels en insistant notamment sur les points suivants: - reactions nucleaires et utilisation des reacteurs; - methodes de separations chimiques et methodes d'enrichissement d'activite des preparations; - protection du personnel et methodes de manipulation. (auteur)

  18. Evaluation of residual stresses in composite materials by using neutron diffraction; study of elasto-plasticity; Etude des composites a matrice metallique par la technique de la diffraction de neutrons: analyse du comportement elastoplastique et evaluation des contraintes residuelles

    Energy Technology Data Exchange (ETDEWEB)

    Levy-Tubiana, R

    1999-11-05

    This work deals with the study of Metal Matrix Composites (MMC) using neutrons diffraction method and the analysis of the elastoplastic behavior in such materials. First, we evaluated macro-stresses in aluminium MMC reinforced with 17%vol. of SiC particles. One of the analyzed sample has been 4 point bending deformed, measurements have been performed after relaxation. The difference between the coefficients of thermal expansion constrains the matrix to be in tensile state and the particles in compressive state in the sample which has not be deformed. In the sample deformed, the MMC response is predicted by the science of Resistance Materials applied to a bent bar. We assume that macro-stresses are the sum of stresses with different origins (elastic, plastic, thermal mismatch): elastic mismatch is evaluated by Eshelby model and we determined micro-stresses in the unbent bar: they are equivalent and constant along width direction. For the bent bar, we observe relaxation of thermal stresses in the surface region. Theses results are confirmed by measurements of tensile/compressive sample using neutrons diffraction method. We also observed the influence of mechanical and thermal treatment on such MMC: the shear stress (established by the auto-coherent model) depends only on the way of cooling. Finally, a study was performed on titanium MMC for SNECMA on rotor beings used in the gas turbine engine industry. Evolution of stresses between felloe and boring is confirmed by a finite elements modeling and they are the first experimental results in this application. (author)

  19. Costs of fuel cycle industrial facilities: an international review; Couts des installations industrielles du cycle du combustible point a l'international

    Energy Technology Data Exchange (ETDEWEB)

    Macias, R.M

    2004-07-01

    This document presents, comments, and compares economic and financial data for industrial facilities concerning different aspects of the nuclear fuel cycle. It first comments the present situation and the short term trends for the natural uranium market, the conversion market, the enrichment market, the reprocessing market, the storage market. It gives an assessment of the elementary costs of the existing facilities for the different stages and processes: reprocessing, spent fuel warehousing (example of the CLAB in Sweden and comparison with other available data), warehousing of all types of wastes (examples of Habog in Netherlands, Zwilag in Switzerland), spent fuel storage (example of Yucca Mountain in the USA, Onkalo in Finland, projects and studies in Sweden), storage of vitrified wastes in Belgium, storing of transuranic wastes in the USA, storage of low and intermediate level and short life wastes in Sweden.

  20. Management of ionizing radiation sources in university, medical and industrial environments; Gestion des sources ionisantes en milieux universitaire, medical et industriel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This conference treats several subjects relative to the use of radioactive sources. The first session comprises three articles about ionizing sources and regulation. The second session, with three articles, tackles the question of radiation protection in the use of sources in industrial field. The third session, four articles, treats the same question but in the medicine and university media. The fourth session (three articles) is devoted to the organisation of radiation protection in the case of accidents. The fifth session concerns the management of spent sources (three articles). The sixth session studies the radiation protection of sources in Europe. The seventh and final session ends with the part and coordination of actors in radiation protection in the sources management (three articles). (N.C.)

  1. À la croisée des univers du transmedia, de la marque et de la franchise dans l’industrie cinématographique

    OpenAIRE

    Laurichesse, Hélène

    2012-01-01

    La montée en puissance de la stratégie de marque et celle de la création transmedia dans les industries créatives nous a conduits à questionner les relations à établir entre ces deux tendances assez systématiquement associées dans la littérature. Sont-elles finalement indépendantes ou interdépendantes ? Nous verrons ainsi que la marque dans le secteur cinématographique n’est pas nécessairement transmedia, mais que la création transmedia s’inscrit de manière plus évidente et plus aboutie que l...

  2. Simulation of rumen fermentation kinetics of by-products from the biodiesel industry with in vitro gas production technique

    Directory of Open Access Journals (Sweden)

    Alex Lopes da Silva

    2015-12-01

    Full Text Available The objective of this study was to investigate the rumen fermentation kinetics of 18 by-products from the biodiesel industry exhibiting potential for use in the feeding of ruminants via the in vitro gas production technique. The following feeds were investigated: cottonseed, canudo de pito, crambe, sunflower, castor seed (detoxified with lime and soybean meals and cottonseed, peanut, babassu, crambe, palm kernel, sunflower, licuri nut, macaúba, forage radish and jatropha cakes. The evaluated parameters were total gas production (VfT, gas production from fibrous carbohydrates (VfFC, gas production from non-fibrous carbohydrates (VfNFC, the degradation rate of fibrous carbohydrates (kdFC, the degradation rate of non-fibrous carbohydrates (kdNFC and lag time (lag. The feeds were grouped into six different groups according to rumen fermentation kinetic parameters and adopting an R2 of 0.8. Forage radish cake and the meals of cottonseed, soybean, crambe and sunflower composed the first group, while the cakes of babassu and sunflower formed the second group. Canudo de pito and castor seed meals and the cakes of cottonseed, licuri and jatropha I and II formed the third group. The fourth group was composed by the cakes of crambe, palm kernel and peanut I. The fifth group was formed by peanut cake II, while macauba fruit cake formed the sixth group. The VfNFC and VfFC varied from 16.72 to 200.07 mL and from 53.09 to 242.12 mL, respectively. The mean kdFC and kdNFC values varied from 0.002 to 0.039% h-1and from 0.022 to 0.430% h-1, respectively. The mean lag and VfT varied from 0.0001 to 5.2029 hours and 136.94 to 301.44 mL, respectively. A number of the products exhibited the potential to replace soybean meal, especially the forage radish cake and cottonseed, crambe and sunflower meals.

  3. STUDY CONCERNING THE PRODUCTION OF BIOMASS PROTEIN BY VALORISATION OF BY-PRODUCTS FROM THE DAIRY INDUSTRY ETUDE CONCERNANT L’OBTENTION DE BIOMASSE PROTEIQUE PAR VALORISATION DES SOUS-PRODUITS DE L’INDUSTRIE LAITIERE

    Directory of Open Access Journals (Sweden)

    LUMINITA GROSU

    2015-07-01

    Full Text Available The development of the food industry ensures the necessary protein for the population and in this perspective the valorisation of by-products from the dairy industry (whey and buttermilk can be a solution in this direction. Whey is a very important substrate for the biosynthesis of single cell protein by its lactose content which is the main source of fermentable substrate for yeasts. As part of our research, the biomass protein was obtained using whey as source of lactose and other sugars and yeast strains of Candida utilis. The modelling program used is 2nd order system centred with three variables: amount of sugar, amount of nitrogen and quantity of phosphorus. The following parameters have been pursued: biomass content, yield of sugar consumption and protein content. The process conditions are influenced by the addition of different nutrients.

  4. National symposium: nuclear technique in industry, medicine, agriculture and environment protection. Abstracts of papers; Krajowe sympozjum: technika jadrowa w przemysle, medycynie, rolnictwie i ochronie srodowiska. Streszczenia referatow

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The National Symposium `Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection` has been held in Rynia near Warsaw from 24 to 27 April 1995. Totally 94 lectures have been presented. The actual state of art in Polish investigations have been shown in all branches of applied nuclear sciences. The plenary session devoted to general topics has began the symposium. Further conference has been divided into 18 subject sessions. There were: (1) radiation technologies in environment protection; (2) radiation technologies in materials engineering; (3) radiation preservation in food; (4) radiation techniques for medical use; (5) radiotracers in industrial investigations; (6) radiotracers in water and sewage management and leak control; (7) tracers in hydrology; (8) radiotracers in materials testing; (9) instruments for environment protection, (10) radiometric industrial gages; (11) diagnostic and testing instruments; (12) application of nuclear techniques in materials testing; (13) applications of nuclear techniques in geology and hydrogeology; (14) radioanalytical methods; (15) radiation detectors; (16) radiation measurements; (17) data processing from radiometric experiments; (18) accelerators, isotopes manufacturing, INIS.

  5. National symposium: nuclear technique in industry, medicine, agriculture and environment protection. Abstracts of papers; Krajowe sympozjum: technika jadrowa w przemysle, medycynie, rolnictwie i ochronie srodowiska. Streszczenia referatow

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The National Symposium `Nuclear Techniques in Industry, Medicine, Agriculture and Environment Protection` has been held in Rynia near Warsaw from 24 to 27 April 1995. Totally 94 lectures have been presented. The actual state of art in Polish investigations have been shown in all branches of applied nuclear sciences. The plenary session devoted to general topics has began the symposium. Further conference has been divided into 18 subject sessions. There were: (1) radiation technologies in environment protection; (2) radiation technologies in materials engineering; (3) radiation preservation in food; (4) radiation techniques for medical use; (5) radiotracers in industrial investigations; (6) radiotracers in water and sewage management and leak control; (7) tracers in hydrology; (8) radiotracers in materials testing; (9) instruments for environment protection, (10) radiometric industrial gages; (11) diagnostic and testing instruments; (12) application of nuclear techniques in materials testing; (13) applications of nuclear techniques in geology and hydrogeology; (14) radioanalytical methods; (15) radiation detectors; (16) radiation measurements; (17) data processing from radiometric experiments; (18) accelerators, isotopes manufacturing, INIS.

  6. Civili, langue des Baloango

    DEFF Research Database (Denmark)

    Mavoungou, Paul Achille; Ndinga-Koumba-Binza, Hugues Steve

    , Congo, Angola, etc.) issus de la décolonisation. Il présente de façon succincte quelques phénomènes historiques, phonologiques, morphosyntaxiques, homonymiques et analogiques de la langue. Des faits sémantiques des emprunts linguistiques y sont également décrits dans le cadre des changements...

  7. Impact of industries in the accumulation of radionuclides in the lower part of Ebro river (Catalonia, Spain); Impact des industries dans l'accumulation de radionucleides dans le cours inferieur de l'Ebre (Catalogne, Espagne)

    Energy Technology Data Exchange (ETDEWEB)

    Palomo, M.; Penalver, A.; Aguilar, C.; Borrull, F. [Unitat de Radioquimica Ambiental i Sanitaria, Universitat Rovira i Virgili, Consorci d' Aigues de Tarragona (CAT), L' Ampolla Tarragona (Spain)

    2010-10-15

    Ebro River extends over almost 930 km and is the main Spanish river entering the Mediterranean Sea. There are several industries located along this river course including a di-calcium phosphate factory (DCP) and two nuclear power reactors. These installations, together with other factors such as the geology, can contribute to the radiological content of the river. Therefore, this study was performed to determine some natural and also some anthropogenic radionuclide concentrations in the Ebro River ecosystem. We analysed water samples, solid samples (rice field sludge and surface marine sediment samples), and also biota samples (Cladophora glomerata and Cynodon dactylon). For water samples, gross alpha, gross beta, tritium, uranium, thorium and also a group of gamma-emitting isotopes' activities were determined. The main contribution to radioactivity for these samples was due to some isotopes from the uranium and thorium chain. For the solid samples, we quantified some natural and artificial gamma radioisotopes, which may be related to the geological and/or industrial activities located in this zone. In the case of biota, the results indicate that the presence of the DCP has a significant influence, since the highest activity was observed in the surroundings of this industry (Flix), where isotopes such as {sup 214}Bi and {sup 214}Pb presented activity values of 105 {+-} 43 Bq/kg and 100 {+-} 58 Bq/kg, respectively. (authors)

  8. Techniques Which Aid in Quantitative Interpretation of Scan Data; Methodes Facilitant l'Interpretation Quantitative des Scintigrammes; Metody, oblegchayushchie kolichestvennuyu interpretatsiyu dannykh skennirovaniya; Tecnicas Que Facilitan la Interpretacion Cuantitativa de los Datos Centelleograficos

    Energy Technology Data Exchange (ETDEWEB)

    Charleston, D. B.; Beck, R. N.; Eidelberg, P.; Schuh, M. W. [Argonne Cancer Research Hospital, Chicago, IL (United States)

    1964-10-15

    This paper discusses a range of techniques which assist in evaluating and interpreting scanning read-out display. This range extends from simple internal calibration for photographic read-out to fairly elaborate auxiliary equipment for presentation of accumulated digital scan information to a computer programme. The direct and remarkably useful method of using a random pulse generator to produce a calibrated step-wedge of spots, which are projected on to a film by the same projection light source as is used during the scan, allows the viewer to compare exposure densities of regions of interest on the scan to similar regions on the wedge which are calibrated directly in count-rate units. Auxiliary equipment, such as a multichannel analyser used in the multiscaling mode, permits the accumulation of digital information for a ''total count per scan line'' display for each index step. Small animal scans have been made which accumulate and display ''counts per scan line'' for each index step. This produces an accurate quantitative measure of the distribution of activity over the animal and a profile display of activity similar to the slit scan display of a linear scanning system. The same multiscaling technique is carried further by accumulating digital information for a ''count per unit area'' display. A profile curve is obtained for each scan line of each index step. From this it is possible to visualize or construct an area profile of count-rate. Scan displays with or without contrast enhancement and with or without ''time lag'' from integrating circuitry and scans with various spot sizes and shapes have been produced under identical statistical conditions by means of multiple read-outs while scanning a phantom with a single-detector system. Direct comparison of displays combined with the ''count per unit area'' mapping technique aid in the interpretation of scan results. 'Precise position information must be included with the data record. Computations of percentage

  9. Barriers to implement green supply chain management in automobile industry using interpretive structural modeling technique: An Indian perspective

    OpenAIRE

    Sunil Luthra; Vinod Kumar; Sanjay Kumar; Abid Haleem

    2011-01-01

    Purpose: Green Supply Chain Management (GSCM) has received growing attention in the last few years. Most of the automobile industries are setting up their own manufacturing plants in competitive Indian market. Due to public awareness, economic, environmental or legislative reasons, the requirement of GSCM has increased.  In this context, this study aims to develop a structural model of the barriers to implement GSCM in Indian automobile industry.Design/methodology/approach: We have ident...

  10. Effets des electrons secondaires sur l'ADN

    Science.gov (United States)

    Boudaiffa, Badia

    Les interactions des electrons de basse energie (EBE) representent un element important en sciences des radiations, particulierement, les sequences se produisant immediatement apres l'interaction de la radiation ionisante avec le milieu biologique. Il est bien connu que lorsque ces radiations deposent leur energie dans la cellule, elles produisent un grand nombre d'electrons secondaires (4 x 104/MeV), qui sont crees le long de la trace avec des energies cinetiques initiales bien inferieures a 20 eV. Cependant, il n'y a jamais eu de mesures directes demontrant l'interaction de ces electrons de tres basse energie avec l'ADN, du principalement aux difficultes experimentales imposees par la complexite du milieu biologique. Dans notre laboratoire, les dernieres annees ont ete consacrees a l'etude des phenomenes fondamentaux induits par impact des EBE sur differentes molecules simples (e.g., N2, CO, O2, H2O, NO, C2H 4, C6H6, C2H12) et quelques molecules complexes dans leur phase solide. D'autres travaux effectues recemment sur des bases de l'ADN et des oligonucleotides ont montre que les EBE produisent des bris moleculaires sur les biomolecules. Ces travaux nous ont permis d'elaborer des techniques pour mettre en evidence et comprendre les interactions fondamentales des EBE avec des molecules d'interet biologique, afin d'atteindre notre objectif majeur d'etudier l'effet direct de ces particules sur la molecule d'ADN. Les techniques de sciences des surfaces developpees et utilisees dans les etudes precitees peuvent etre etendues et combinees avec des methodes classiques de biologie pour etudier les dommages de l'ADN induits par l'impact des EBE. Nos experiences ont montre l'efficacite des electrons de 3--20 eV a induire des coupures simple et double brins dans l'ADN. Pour des energies inferieures a 15 eV, ces coupures sont induites par la localisation temporaire d'un electron sur une unite moleculaire de l'ADN, ce qui engendre la formation d'un ion negatif transitoire

  11. Des racines et des ailes

    Directory of Open Access Journals (Sweden)

    Stéphanie Vincent-Geslin

    2012-05-01

    Full Text Available Les mobilités pendulaires semblent être en augmentation en Europe depuis une dizaine d’années. Cette croissance du temps passé à se déplacer amène à remettre en question la conjecture de Zahavi et apparaît relativement inexplicable en regard du paradigme classique de l’acteur rationnel traditionnellement utilisé dans le champ des transports. Si, dans la littérature, les temps de déplacements sont principalement expliqués par le contexte résidentiel, la forme urbaine et le travail, ce cadre explicatif ne dit rien des processus de décision eux-mêmes qui amènent aux pendularités intensives.À partir d’une enquête qualitative menée auprès de pendulaires français, suisses et belges, cette contribution propose d’analyser les arbitrages et les éléments déterminants des processus de la grande pendularité. Les mobilités quotidiennes pendulaires apparaissent comme le résultat de compromis entre activité professionnelle, attachement résidentiel et choix de vie et prennent ainsi la forme de stratégies de conciliation entre vie privée et vie professionnelle. Ces mobilités spatiales permettent alors paradoxalement la préservation des ancrages résidentiels, sociaux et familiaux.Roots and wings. Long-distance commuting patterns, or how to conciliate professional and personal lifeLong-distance commuting patterns appear to be increasing in Europe over the last ten years. These raising mobility patterns lead to reappraise the Zahavi conjecture and appear largely inexplicable by the classical rational actor paradigm traditionally used in transportation research. In literature, commuting is mainly explained by residential contexts, urban forms and job. Nevertheless this theoretical frame says little about the decision-making processes themselves. Based on a qualitative survey conducted in three European countries - France, Belgium and Switzerland – among a population of high commuters, this paper proposes an analysis of

  12. Industrial Ultrasonic Inspection of Stainless-Steel Claddings for the EL4 Reactor; Controle Industriel par Ultrasons des Gaines en Acier Inoxydable du Reacteur EL4; Promyshlennyj kontrol' obolochechnykh trub iz nerzhaveyushchej stali reaktora dlya EL4 s pomoshch'yu ul'trazvukovogo metoda; Metodos Ultrasonicos para Control Industrial de las Vainas de Acero Inoxidable del Reactor EL4

    Energy Technology Data Exchange (ETDEWEB)

    Prot, A. C.; Foulquoer, H. E.; Peyrot, J. P. [Centre d' Etudes Nucleaires de Saclay (France)

    1965-09-15

    Improved reactor performance requires the use of accurately fabricated and carefully inspected components. One inspection relates to the quality of the cladding tubes, whose mechanical reliability is essential for economic reactor operation. The choice and development of a method is a difficult matter and the authors explain the main factors involved. Once the choice has been made and the method has been developed in the laboratory, two new problems arise: Adaptation to meet industrial requirements; and The need to reconcile the quality standards attainable with the manufacturing process at any given stage and the somewhat arbitrarily defined specifications for the finished product. In practice, this involves a statistical study of batches of tubes from various sources and their classification in relation to more or less strict thresholds. The number of tubes which have to be inspected is much larger than originally expected. This has led to the design of an automatic inspection device geared both to the output rates involved and to the requirements of the type of inspection adopted; the latter are generally mechanical and impose particularly careful product fabrication. These various characteristics are now embodied in a device whose capacity can already easily meet the requirements of a fuel-element production line. The potentialities of the device are closely dependent on the characteristics of the inspection equipment used, especially the performances of the electronic part of ultrasonic inspection instruments and of the transducers. This study shows that standard equipment is not very suitable and that immediate thought should be given to special instruments for this type of inspection. (author) [French] L'accroissement des performances des reacteurs necessite l'utilisation de materiaux finement elabores et soigneusement controles. L'un des aspects de ce controle est celui de la qualite des tubes de gainage utilises, dont la tenue mecanique est un facteur

  13. Capital and operating costs of irradiated natural uranium reprocessing plants; Couts d'investissement et d'exploitation des usines de retraitement de l'uranium naturel irradie

    Energy Technology Data Exchange (ETDEWEB)

    Thiriet, L; Jouannaud, C; Couture, J; Duboz, J [Commissariat a l' Energie Atomique (France). Centre d' Etudes Nucleaires; Oger, C [Saint Gobain Nucleaire (France)

    1966-07-01

    This paper presents first a method of analysing natural uranium reprocessing plants investment costs (method similar to LANG and BACH well known in the fuel oil industry) and their operating costs (analysed according to their economic type). This method helps establishing standard cost structures for these plants, allowing thus comparisons between existing or planned industrial facilities. It also helps evaluating the foreseeable consequences of technical progress. Some results obtained are given, concerning: the investment costs sensitivity to the various technical parameters defining the fuel and their comparison according to the country or the economic area taken into account. Finally, the influence of the plants size on their investment costs is shown. (author) [French] La communication expose d'abord une methode d'analyse des couts d'investissement des usines de retraitement de l'uranium naturel irradie (inspiree de celles de LANG et de BACH, bien connues dans l'industrie petroliere) et de leurs couts d'exploitation (selon leur nature economique). Cette methode permet d'etablir des structures types de couts de ces usines et de comparer les realisations industrielles et les projets. Elle facilite l'exploration des consequences previsibles du progres technique. On indique un certain nombre de resultats obtenus, concernant la sensibilite des couts d'investissement de ces usines aux differents parametres techniques definissant le combustible et leur confrontation selon les pays ou aires economiques envisages. On montre enfin comment doit pouvoir s'exprimer l'influence de la taille des usines sur leur cout d'investissement. (auteur)

  14. Assistance to the industrial process supervision: toward a methodology of conception; Aide a la supervision des processus industriels: vers une methodologie de conception

    Energy Technology Data Exchange (ETDEWEB)

    Benkhannouche, S

    1996-05-31

    This thesis presents a methodological approach to the design of computerized assistance for operators in control industrial processes. We are particularly interested in how to find the solutions which best suit their needs. Our preferred approach is focused on the operator: the main factors influencing his performance are reviewed and we make a synthesis which consists of a categorized list, or typology, of the extents of the operators` activities, tasks and errors. This typology is then used to classify the possible improvements as well as associated computer aids. The DIAPASON held system for fault diagnosis is integrated in this structure. This typology is our chosen basis for defining a specification method which enables the quality of the designed system to be guarantee. We propose a phased approach, the first phase of which involves analysing needs and thus identifying the objectives of the project. The second phase is the preparation of a performance specification which serves as a reference system for the project. In the third phase technical solutions are proposed to meet the requirements set out in the performance specification. The following phases involve studying the technical feasibility of the proposed solutions and the actual development of the system. Together with the feasibility study comes the step of making up a knowledge bank. The usual method of systems analysis are included in the typology of the aids. Furthermore, the SAGACE method uses a new approach to systems analysis based on its description which unites various points of view ; the evaluation of its possibilities forms a part of the construction of a reference system which gathers up the information needed to put the DIAPASON diagnosis system into action. (author).

  15. Eco-efficience et analyse des couts du cycle de vie: Developpement d'un outil d'aide a la conception dans l'industrie aeronautique

    Science.gov (United States)

    Mami, Fares

    The aeronautical sector, responsible for about 3 % of the world emissions of greenhouse gases, predict a 70 % growth in 2025 and 300 % to 500 % in 2050 of its emissions compared to the level of 2005. The decision-makers must thus be supported in their choice of conception to integrate the environmental aspect into the decision-making. Our industrial partner in the aeronautical sector developed an expertise in Life Cycle Assessment (LCA) and seeks to integrate the costs and the environmental impacts in a systematic way into the ecodesign of products. Based on the literature review and the objectives of this research we propose a model of eco-efficiency, which integrates LCA with Life Cycle Costing (LCC). This model is consistent with defined cost cutting and environmental impacts reduction targets and allows a simple interpretation of the results while minimizing the efforts during data collection. The model is applied for 3D printing as an alternative production process in the manufacturing of an aircraft blocker door. 3D printing is a new technology of production working by addition of material and present interesting opportunities of cost cutting and environmental impacts, particularly in the aeronautical domain. The results showed that 3D printing, when associated with improvement in the topology of the part, allows an improvement both on costs and environmental impacts of the part life cycle. Nevertheless, the results are sensitive to the productivity of the 3D printing machine, in particular with costs when the productivity of the 3D printing is reduced. This eco-efficiency model presents several opportunities of improvement. A more elaborate definition of the objectives in reduction of environmental impacts would allow to direct the choices in design to considerations of eco-efficiency at a macro level. Moreover, the integration of the social dimension in the model constitutes an important stage to operationalize the stakes of environmental and social

  16. Food surveys for assessing chemical and dosimetric impacts near industrial sites; Enquetes alimentaires pour l'evaluation des impacts chimiques et dosimetriques a proximite de sites nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Parache, V.; Maurau, S.; Mercat, C.

    2011-03-15

    Estimating the ingestion of potentially contaminated foodstuffs around conventional and nuclear industrial sites requires data about the food practices and eating habits of the local residents, especially the consumption of locally- and home-produced food. The IRSN thus chose to conduct surveys about these practices in the vicinity of nuclear sites. Their methodology was based on previous surveys near nuclear sites. In 2004, in partnership with AREVA and BEGEAT, the French Institute for Radioprotection and Nuclear Safety studied the eating habits of the residents of Bollene, near the Tricastin plant (Rhone Valley), with the aim of improving the quantification of the plant's potential health impacts. Based on these studies and as part of the SENSIB project to characterize vulnerability to nuclear risks, we developed and tested a survey protocol during the summer 2008, around the Chinon nuclear plant, in collaboration with EDF. The protocol is currently being tested around the Marcoule nuclear plant, in collaboration with the CEA. The aim was to optimize the feasibility and the reproducibility of the approach, while losing none of the robustness of the results. The data obtained made it possible to evaluate daily food intake values for individuals and to assess the rates of consumption of locally-grown products for many food categories. The data showed the existence of local population groups with very high rates of locally-grown food consumption - over 90 % of certain food products. This comparative study thus shows the significant variability of eating habits in the French population and proposes a reproducible approach to evaluating realistic indicators of potentially risky dietary habits. (authors)

  17. Use of an oscillation technique to measure effective cross-sections of fissionable samples in critical assemblies; Mesure des sections efficaces effectives d'echantillons fissiles par une methode d'oscillation dans les-assemblages critiques

    Energy Technology Data Exchange (ETDEWEB)

    Tretiakoff, O; Vidal, R; Carre, J C; Robin, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    The authors describe the technique used to measure the effective absorption and neutron-yield cross-sections of a fissionable sample. These two values are determined by analysing the signals due to the variation in reactivity (over-all signal) and the local perturbation in the flux (local signal) produced by the oscillating sample. These signals are standardized by means of a set of samples containing quantities of fissionable material ({sup 235}U) and an absorber, boron, which are well known. The measurements are made for different neutron spectra characterized by lattice parameters which constitute the central zone within which the sample moves. This technique is used to study the effective cross-sections of uranium-plutonium alloys for different heavy-water and graphite lattices in the MINERVE and MARIUS critical assemblies. The same experiments are carried out on fuel samples of different irradiations in order to determine the evolution of effective cross-sections as a function of the spectrum and the irradiations. (authors) [French] On decrit la methode utilisee pour mesurer les sections efficaces effectives d'absorption et de production de neutrons d'un echantillon fissile. Ces deux grandeurs sont determinees en analysant les signaux dus a la variation de reactivite (signal global) et a la perturbation locale de flux (signal local) produits par l'echantillon oscillant. Ces signaux sont etalonnes a l'aide d'un jeu d'echantillons dont les teneurs en materiau fissile ({sup 235}U) et en absorbeur (bore) sont bien connues. Les mesures sont realisees pour differents spectres de neutrons caracterises par les parametres du reseau constituant la zone centrale a l'interieur de laquelle se deplace l'echantillon. A l'aide de cette methode on etudie les sections efficaces effectives d'alliage uranium-plutonium pour differents reseaux a eau lourde et a graphite dans les assemblages crtiques MINERVE et MARIUS. Les memes experiences sont effectuees sur des echantillons de

  18. Modelling Laser Milling of Microcavities for the Manufacturing of DES with Ensembles

    Directory of Open Access Journals (Sweden)

    Pedro Santos

    2014-01-01

    Full Text Available A set of designed experiments, involving the use of a pulsed Nd:YAG laser system milling 316L Stainless Steel, serve to study the laser-milling process of microcavities in the manufacture of drug-eluting stents (DES. Diameter, depth, and volume error are considered to be optimized as functions of the process parameters, which include laser intensity, pulse frequency, and scanning speed. Two different DES shapes are studied that combine semispheres and cylinders. Process inputs and outputs are defined by considering the process parameters that can be changed under industrial conditions and the industrial requirements of this manufacturing process. In total, 162 different conditions are tested in a process that is modeled with the following state-of-the-art data-mining regression techniques: Support Vector Regression, Ensembles, Artificial Neural Networks, Linear Regression, and Nearest Neighbor Regression. Ensemble regression emerged as the most suitable technique for studying this industrial problem. Specifically, Iterated Bagging ensembles with unpruned model trees outperformed the other methods in the tests. This method can predict the geometrical dimensions of the machined microcavities with relative errors related to the main average value in the range of 3 to 23%, which are considered very accurate predictions, in view of the characteristics of this innovative industrial task.

  19. Law project on the gas utility modernization and gas industries development. Law project synthesis on the gas utility modernization and gas industries development; Projet de loi relatif a la modernisation du service public du gaz naturel et au developpement des entreprises gazieres.Synthese du projet de loi sur la modernisation du service public du gaz et le developpement des entreprises gazieres

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    The french government would like to develop a law concerning the gas utility modernization and gas industries development, which completes the today system, more particularly, the law of 1946. This project specifies and comforts the gas utility, it gives to the energy policy tools adapted to the new european context. It helps the natural gas industry to become more competitive. The method chosen by the government is presented and discussed in these three documents. (A.L.B.)

  20. Optimisation des paramètres de dépôt de a-Si:H dans la technique ...

    African Journals Online (AJOL)

    -photo-CVD technique, known for its use in eveloping thin film of semiconductor materials and dielectrics has been a resurgence of interest in view of their many applications in microelectronics. It is established that the physico-chemical and ...

  1. Techniques simplifiées pour le dénombrement et l'identification des microorganismes vivants dans les moûts et les vins

    Directory of Open Access Journals (Sweden)

    Suzanne Lafon-Lafourcade

    1979-12-01

    The number of microorganisms species occuring in musts and wines (yeasts, lactic and acetic bacteria is limited. It is presented a quick, selective technique to count these miscellaneous microorganisms and application of Api-system for identification of yeasts and lactic bacteria of wine.

  2. The nuclear techniques in function of improving the efficiency of the flocculators and floats in the industrial waste treatment station of PETROBRAS

    International Nuclear Information System (INIS)

    Damera Martinez, Arnaldo; Ramos Espinosa, Kenia A.; Pinto, Amenonia Ferreira; Barbalho, Andrea de Magalhaes; Derivet Zarzabal, Milagros

    2001-01-01

    This work was carried out in the Station of Treatment of Industrial Waste (STIW) in PETROBRAS (Brazil). The STIW has the function of receiving, to treat and storage liquid wastes coming from diverse points of the refinery, avoiding the environment contamination. This study consists on the determination of the time of residence inside the flocculators and floats, by means of nuclear technique of radioactive tracer, using Tc-99m. This technique has a great economic and environmental importance because the time of residence obtained experimentally in the flocculators and the floats, can be compared with those obtained theoretically, which allow to influence on the system, optimizing its operation

  3. The liberalization of the European electric and gas industries through the firms' M and A and investment strategies: propositions for a better energy security; Le processus de liberalisation des industries electriques et gazieres europeennes a travers les strategies de fusion - acquisition et d'investissement des firmes - propositions pour une securite energetique renforcee

    Energy Technology Data Exchange (ETDEWEB)

    Benhassine, W.

    2009-04-15

    The electric and gas industries have been traditionally managed by public monopolies. The post World War II context was supportive to such an industrial organization. In fact, Europe was getting engaged in a long period of economic growth and was benefiting a favorable energetic context. At the end of the 90's, Europe decides to liberalize the national energy industries in order to create a unique European energy market. This liberalization has occurred in a context that as dramatically changed from the economic and energetic perspective. Indeed, the globalization phenomenon has strengthened the competitiveness of the emerging economies. The strong growth of the energy demand and the stagnation of the supply on the offer side have created tensions which have been increasingly frequent and important on the energy markets. Besides, facing greater budget restrictions and financial difficulties, the states have wished to get financially disengaged from these industries. Many factors show that the economic and energetic context will not get better in the next decades. Hence, in this new context, the liberalization of the energy industries should respond to two major stakes for the energy security of the European countries: the sustainability of the investments and the control of the energy demand. After having studied the merger and investment strategies of the energy firms, operating within a freshly liberalized sector, we make some propositions to draw up a new industrial organization which would allow a more efficient response to these two stakes. (author)

  4. A Novel Environmental Performance Evaluation of Thailand’s Food Industry Using Structural Equation Modeling and Fuzzy Analytic Hierarchy Techniques

    Directory of Open Access Journals (Sweden)

    Anirut Pipatprapa

    2016-03-01

    Full Text Available Currently, the environment and sustainability are important topics for every industry. The food industry is particularly complicated in this regard because of the dynamic and complex character of food products and their production. This study uses structural equation modeling (SEM and a fuzzy analytic hierarchy process (FAHP to investigate which factors are suitable for evaluating the environmental performance of Thailand’s food industry. A first-stage questionnaire survey was conducted with 178 managers in the food industry that obtained a certificate from the Department of Industrial Work of Thailand to synthesize the performance measurement model and the significance of the relationship between the indicators. A second-stage questionnaire measured 18 experts’ priorities regarding the criteria and sub-factors involved in the different aspects and assessment items regarding environmental performance. SEM showed that quality management, market orientation, and innovation capability have a significantly positive effect on environmental performance. The FAHP showed that the experts were most concerned about quality management, followed by market orientation and innovation capability; the assessment items for quality policy, quality assurance, and customer orientation were of the most concern. The findings of this study can be referenced and support managerial decision making when monitoring environmental performance.

  5. Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

    Energy Technology Data Exchange (ETDEWEB)

    Fontaine, Y [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

  6. Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

    Energy Technology Data Exchange (ETDEWEB)

    Fontaine, Y. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

  7. Report on the present day situation and technical perspectives of renewable energies; Rapport sur l'etat actuel et les perspectives techniques des energies renouvelables

    Energy Technology Data Exchange (ETDEWEB)

    Birraux, C; Le Deaut, J Y

    2001-11-01

    This work, carried out by the parliamentary office for the evaluation of scientific and technological choices on request of the French National Assembly and Senate, takes stock of the present day situation and technical perspectives of development of renewable energy sources and of research needs of the French industry in this domain: 1 - renewable energies: key-technologies for the energy supply of developing countries and for a rational consumption in transportation systems and accommodations of developed countries (energies technically different from fossil or nuclear energies; fundamental energy sources for a developing world; different national goals in Europe depending on the available natural resources and on the political realities; a minor interest in France for the domestic power generation but a major interest for transports, residential and tertiary sectors and export); 2 - priority choices given to the French renewable energy resources: renewable electricity (photovoltaic, wind, biomass), thermal technologies (solar, geothermal, biomass); 3 - future policy: sustain of renewable electricity production with the revival of research, industry and technical cooperation. (J.S.)

  8. Pratiques enseignantes et réalité professionnelle : cas d’enseignants des lycées techniques et professionnels industriels au Gabon

    Directory of Open Access Journals (Sweden)

    EMMANUEL MOUDOUMA

    2011-07-01

    Full Text Available This article presents the outcomes of a study on the practises of Gabonese teachers who teach in the fields of industrial technical and vocational education. This study is interested in their daily activities and aims at characterising the inevitable variation which exists between the knowledge with work in the production activities industrial in company and those implemented in the institutions of vocational training. More generally, it is a question of appreciating the relation between training and employment. Thus, we are interested in the orientation given by the teacher to his daily practise to reduce or not this variation. The results of this study highlight the impact of epistemological and pragmatic dimensions on the organisation of the activities and thus on the practises. Obviously, the level of entry in the technical school course, the first job, the transport conditions, the appropriation of the reference frame of training and the development of the contents of courses are some of the items which impact this process of reduction of the difference between the two forms of knowledge.

  9. Report on the present day situation and technical perspectives of renewable energies; Rapport sur l'etat actuel et les perspectives techniques des energies renouvelables

    Energy Technology Data Exchange (ETDEWEB)

    Birraux, C.; Le Deaut, J.Y.

    2001-11-01

    This work, carried out by the parliamentary office for the evaluation of scientific and technological choices on request of the French National Assembly and Senate, takes stock of the present day situation and technical perspectives of development of renewable energy sources and of research needs of the French industry in this domain: 1 - renewable energies: key-technologies for the energy supply of developing countries and for a rational consumption in transportation systems and accommodations of developed countries (energies technically different from fossil or nuclear energies; fundamental energy sources for a developing world; different national goals in Europe depending on the available natural resources and on the political realities; a minor interest in France for the domestic power generation but a major interest for transports, residential and tertiary sectors and export); 2 - priority choices given to the French renewable energy resources: renewable electricity (photovoltaic, wind, biomass), thermal technologies (solar, geothermal, biomass); 3 - future policy: sustain of renewable electricity production with the revival of research, industry and technical cooperation. (J.S.)

  10. Cereal bran fractionation: processing techniques for the recovery of functional components and their applications to the food industry.

    Science.gov (United States)

    Soukoulis, Christos; Aprea, Eugenio

    2012-04-01

    Bran is the outer part of cereal grains that is separated during the cereals de-hulling and milling processes. It was considered in the past a by-product of cereal industry employed mainly as animal feed. Cereal bran, being particularly rich in different functional biopolymers, bio-active compounds and essential fatty acids, attracted the interest of pharmaceutical and food industry. Furthermore, the peculiar techno-functional properties of brans together with their particular physiological and nutritional aspects have led to a great interest in their incorporation as main or secondary components in different groups of food products including bakery and confectionery products, breakfast cereals and extruded foodstuffs, emulsions and functional dairy products and pasta products. In the first part of the present work the main fractionation processes, bran fractions properties and their physicochemical and technological properties are briefly reviewed. In the second part, relevant applications, with emphasis on patents, in food industry are reviewed as well.

  11. The "Conservatoire National des Arts et Metiers"

    Science.gov (United States)

    Kuhn, Gerard

    2004-01-01

    The overall mission of the Conservatoire national des arts et metiers--(CNAM) [National Conservatory of Industrial Arts and Trades] is outlined. One of its centers, the "Centre national de l'entrepreneuriat"--(CNE) [National Center for Entrepreneurship] is described in greater detail. In particular, this center offers various services, notably…

  12. Total-Factor Energy Efficiency (TFEE Evaluation on Thermal Power Industry with DEA, Malmquist and Multiple Regression Techniques

    Directory of Open Access Journals (Sweden)

    Jin-Peng Liu

    2017-07-01

    Full Text Available Under the background of a new round of power market reform, realizing the goals of energy saving and emission reduction, reducing the coal consumption and ensuring the sustainable development are the key issues for thermal power industry. With the biggest economy and energy consumption scales in the world, China should promote the energy efficiency of thermal power industry to solve these problems. Therefore, from multiple perspectives, the factors influential to the energy efficiency of thermal power industry were identified. Based on the economic, social and environmental factors, a combination model with Data Envelopment Analysis (DEA and Malmquist index was constructed to evaluate the total-factor energy efficiency (TFEE in thermal power industry. With the empirical studies from national and provincial levels, the TFEE index can be factorized into the technical efficiency index (TECH, the technical progress index (TPCH, the pure efficiency index (PECH and the scale efficiency index (SECH. The analysis showed that the TFEE was mainly determined by TECH and PECH. Meanwhile, by panel data regression model, unit coal consumption, talents and government supervision were selected as important indexes to have positive effects on TFEE in thermal power industry. In addition, the negative indexes, such as energy price and installed capacity, were also analyzed to control their undesired effects. Finally, considering the analysis results, measures for improving energy efficiency of thermal power industry were discussed widely, such as strengthening technology research and design (R&D, enforcing pollutant and emission reduction, distributing capital and labor rationally and improving the government supervision. Relative study results and suggestions can provide references for Chinese government and enterprises to enhance the energy efficiency level.

  13. Approaches, techniques, and information technology systems in the restaurants and foodservice industry: a qualitative study in sales forecasting.

    OpenAIRE

    Green, Yvette N. J.; Weaver, Pamela A.

    2008-01-01

    This is a study of the approaches, techniques, and information technology systems utilized for restaurant sales forecasting in the full-service restaurant segment. Companies were examined using a qualitative research methods design and long interviews to gather information on approaches, techniques, and technology systems utilized in the sales forecasting process. The results of the interviews were presented along with ensuing discussion.

  14. Flying with doctors: Experiences with the application of 6 techniques from aviation industry in the Rotterdam Eye Hospital

    NARCIS (Netherlands)

    D.F. de Korne (Dirk); U.F. Hiddema (Frans); F.G. Bleeker (Fred); N.S. Klazinga (Niek)

    2008-01-01

    textabstractIntoduction. Aviation industry is often put forward as an example in creating safer health care. Comparing aviation and health care, there are similarities in using technology, working with highly specialized professional teams and the need for dealing with risk and uncertainties (Sexton

  15. Profil clinique et anatomopathologique des cancers de l'ovaire

    African Journals Online (AJOL)

    recueillies selon la méthode documentaire. Les données cliniques contenues dans chaque dossier ont été consignées sur une fiche technique anonyme. Celles relatives au diagnostic anatomopathologique ont été relevées à partir des archives des diagnostics du service d'anatomie et de cytologie pathologiques.

  16. Contribution a l'amelioration des techniques de diagnostic des ...

    African Journals Online (AJOL)

    Recurring fever is manifested by high fever with headache, vomiting, fatigue and feeling cold. These symptoms make recurring fever be confused either with malaria or with fever of unknown etiology. The purpose of this work is to make available to research laboratories in endemic areas of malaria and relapsing fever ...

  17. Plasmas pour valorisation totale ou partielle des gaz contenant de l'H2S Plasmas for Total Or Partial Upgrading of H2s Containing Gases

    Directory of Open Access Journals (Sweden)

    Czernichowski A.

    2006-12-01

    Full Text Available Des procédés par plasmas alternatifs au procédé Claus sont proposés pour produire de l'hydrogène et récupérer du soufre à partir des gaz contenant une forte teneur en H2S. Quand la teneur en H2S est moins importante, des techniques plasma peuvent également être utiles pour assister certains étages du procédé classique Claus ou réaliser ce procédé pour des gaz non conventionnels. Les tests allant jusqu'à l'échelle industrielle sont menés dans divers réacteurs à plasmas et les résultats encourageants rapportés de la littérature et de la recherche propre laissent envisager des prochaines applications. Plasma assisted processes are proposed to act as an alternative to the Claus process in order to recover hydrogen and sulphur from high H2S gases. For less concentrated gases plasma techniques may also be inserted into classical Claus plant or may allow treatment of non conventional gases. Up to industrial scale tests are performed using different plasma reactors. The literature-based results as well as our own ones make the future applications quite optimistic.

  18. Techniques de séchage des starters lactiques et mécanismes affectant la viabilité cellulaire suite à la lyophilisation

    Directory of Open Access Journals (Sweden)

    Coulibaly, I.

    2011-01-01

    Full Text Available Preservation of industrial's lactic acid bacteria (probiotics by freeze-drying. Majority of the lactic acid bacteria have important nutritional needs and do not have resistance against the environmental conditions surrounding their production (drying, storage, etc. and their use in vivo (physico-chemical properties of the digestive tract. In this condition, industrialists and microbiologists develop regularly research projects of new lactic bacteria able to support the whole of the processes of production, storage and formulation without losing their functional properties. Among the various methods of drying (atomization, fluidization and freeze-drying, freeze-drying makes it possible to obtain a thorough dehydration compatible with very long storage times. This method involves changes in product temperature and is enough aggressive for microorganisms because they require freezing that is not without consequences for cells. In other cases, it causes cellular (peroxydation of the fatty-acids and genetic (modification of proteins deteriorations. The use of cryoprotecteurs during freeze-drying and of antioxidants during storage appreciably increases the rate of viability of these cells.

  19. Measurement of residence time distribution of liquid phase in an industrial-scale continuous pulp digester using radiotracer technique.

    Science.gov (United States)

    Sheoran, Meenakshi; Goswami, Sunil; Pant, Harish J; Biswal, Jayashree; Sharma, Vijay K; Chandra, Avinash; Bhunia, Haripada; Bajpai, Pramod K; Rao, S Madhukar; Dash, A

    2016-05-01

    A series of radiotracer experiments was carried out to measure residence time distribution (RTD) of liquid phase (alkali) in an industrial-scale continuous pulp digester in a paper industry in India. Bromine-82 as ammonium bromide was used as a radiotracer. Experiments were carried out at different biomass and white liquor flow rates. The measured RTD data were treated and mean residence times in individual digester tubes as well in the whole digester were determined. The RTD was also analyzed to identify flow abnormalities and investigate flow dynamics of the liquid phase in the pulp digester. Flow channeling was observed in the first section (tube 1) of the digester. Both axial dispersion and tanks-in-series with backmixing models preceded with a plug flow component were used to simulate the measured RTD and quantify the degree of axial mixing. Based on the study, optimum conditions for operating the digester were proposed. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Use of the Neutron Die-Away Technique to Test Control Rod Effectiveness Theories; Emploi de la Methode d'Absorption des Neutrons pour Verifier les Theories sur l'Efficacite des Barres de Commande; Ispol'zovanie metoda spada potoka nejtronov dlya proverki teorij ehffektivnosti reguliruyushchikh sterzhnej; Aplicacion de la Tecnica de Extincion Neutronica a la Verificacion de las Teorias sobre la Eficacia de las Barras de Control

    Energy Technology Data Exchange (ETDEWEB)

    Perez, R. B. [University of Florida, Gainesville, FL (United States); De Saussure, G.; Silver, E. G. [University of Florida, Gainesville, FL (United States); Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    1964-04-15

    The calculation of control tod effectiveness is complicated by its dependence on both the neutron energy distribution and the geometry of the assembly. When one compares the theory with experimental results obtained from either reactors or subcritical systems, difficulties arise in the comparison because of the intrinsic complexity of such systems. The neutron die-away technique affords the possibility of having an all-thermal neutron model, in which the neutron energy distribution can be separated from spatial effects. Hence, the geometrical factor of the control rod effectiveness can be studied without regard to the details of the neutron spectrum, and the results compared with a clean, simple experimental set-up. The method is based on the fact that in a neutron die- away experiment of the type described here, the buckling of the assembly is related to the decay constant of the fundamental mode by B{sup 2} = ({lambda} - {lambda}{sub a})/D {lambda}{sub a} = inverse lifetime of the neutrons in moderator (s{sup -1}) D = diffusion constant (cm{sup 2}/s). The moderating assemblies used for these experiments were rectangular prisms of beryllium, built in several sizes from small (2.54 cm high, 7.3 cm square) blocks. Three types of cadmium control rods were used: thin 0.476 cm diameter rods; a cruciform-section rod; and hollow ''thick'' rods 7.3 cm x 7.3 cm crosssection. The theoretical schemes tested were: (1) Nordheim-Scalettar (2) Hurwitz-Roe (3) Numerical Diffusion Code. The-effect of a cruciform absorber was computed by using the Hurwitz-Roe conformal transformation technique and value of 0.0188 cm{sup -2} was found for the buckling which compares with the experimental results of 0.0187 {+-} 0.0006 cm{sup -2}. For the thick rods, both Nordheim-Scalettar and the diffusion code overestimated the experimental results by about 10%. However, the interaction between thick rods was correctly predicted by both methods. For thin rods, the Nordheim-Scalettar technique was