WorldWideScience

Sample records for technical inter-instrument variability

  1. Unit-specific calibration of Actigraph accelerometers in a mechanical setup - is it worth the effort? The effect on random output variation caused by technical inter-instrument variability in the laboratory and in the field

    DEFF Research Database (Denmark)

    Moeller, Niels C; Korsholm, Lars; Kristensen, Peter L

    2008-01-01

    *min-1 vs. calibrated SDbetween units = 67 counts*min-1). However, the effect of applying the derived calibration to children's and adolescents' free living physical activity data did not alter the coefficient of variation (CV) (children: CVraw = 30.2% vs. CVcalibrated = 30.4%, adolescents: CVraw = 36...... accelerometers in a mechanical setup using four different settings varying in frequencies and/or amplitudes. Calibration effect was analysed by comparing raw and calibrated data after applying unit-specific calibration factors to data obtained during quality checks in a mechanical setup and to data collected...... conditions had no apparent effect on inter-instrument variability. In all probability, the effect of technical calibration was primarily attenuated in the field by other more dominant sources of variation. However, routine technical assessments are still very important for determining the acceleration...

  2. Inter-instrumental method transfer of chiral capillary electrophoretic methods using robustness test information.

    Science.gov (United States)

    De Cock, Bart; Borsuk, Agnieszka; Dejaegher, Bieke; Stiens, Johan; Mangelings, Debby; Vander Heyden, Yvan

    2014-08-01

    Capillary electrophoresis (CE) is an electrodriven separation technique that is often used for the separation of chiral molecules. Advantages of CE are its flexibility, low cost and efficiency. On the other hand, the precision and transfer of CE methods are well-known problems of the technique. Reasons for the more complicated method transfer are the more diverse instrumental differences, such as total capillary lengths and capillary cooling systems; and the higher response variability of CE methods compared to other techniques, such as liquid chromatography (HPLC). Therefore, a larger systematic change in peak resolutions, migration times and peak areas, with a loss of separation and efficiency may be seen when a CE method is transferred to another laboratory or another type of instrument. A swift and successful method transfer is required because development and routine use of analytical methods are usually not performed in the same laboratory and/or on the same type of equipment. The aim of our study was to develop transfer rules to facilitate CE method transfers between different laboratories and instruments. In our case study, three β-blockers were chirally separated and inter-instrumental transfers were performed. The first step of our study was to optimise the precision of the chiral CE method. Next, a robustness test was performed to identify the instrumental and experimental parameters that were most influencing the considered responses. The precision- and the robustness study results were used to adapt instrumental and/or method settings to improve the transfer between different instruments. Finally, the comparison of adapted and non-adapted transfers allowed deriving some rules to facilitate CE method transfers. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Fuzzy variable linear programming with fuzzy technical coefficients

    Directory of Open Access Journals (Sweden)

    Sanwar Uddin Ahmad

    2012-11-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE Fuzzy linear programming is an application of fuzzy set theory in linear decision making problems and most of these problems are related to linear programming with fuzzy variables. In this paper an approximate but convenient method for solving these problems with fuzzy non-negative technical coefficient and without using the ranking functions, is proposed. With the help of numerical examples, the method is illustrated.

  4. Intra-rater and Inter-instrument Reliability on Range of Movement of Active Knee Extension

    Directory of Open Access Journals (Sweden)

    Germanna de Medeiros Barbosa

    Full Text Available Abstract The objective of the present study was to evaluate the reliability of intra-rater and inter-instrument measures during two flexibility programs. Fifty-three active and healthy males, aged between 18 and 28 years old, were randomly included in three groups: control (Cg, n = 18, static stretching (SSg, n = 17, and dynamic stretching (DSg, n = 18. All participants underwent measurements of their active range of knee extension using manual goniometry and computerized photogrammetry, measured in four separated assessments and analyzed using the SPSS, with ((5%. Both methodologies presented very strongintra-raterreliability (ICC: 0.91(0.99; P<0.001 at all four assessments in all the groups, and the instruments showed weak (r: 0.31-0.6 to strong(r: 0.61-0.9 correlation, in the Cg (P<0.05 and strong (r: 0.61-0.9 in the SSg and DSg (P<0.01, although without differences between groups, indicating that the measures are equally reliable, regardless of interventions.

  5. Organizational vs. technical variables: impact on the collective aspects of healthcare work situations.

    Science.gov (United States)

    Pelayo, Sylvia; Anceaux, Françoise; Rogalski, Janine; Beuscart-Zephir, Marie-Catherine

    2009-01-01

    This study addresses the question of the respective impact of organizational vs. technical environment variables on the collective aspects of healthcare work situations. It analyzes the physicians-nurses communications during the medication use process, according to both the organization of their work and their technical environment. It demonstrates that the organizational variables have a larger impact than the technical environment on the communications and cooperation activities.

  6. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort Derived Variables. Technical Report 69

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2012

    2012-01-01

    This technical report details the derived variables developed for users of the Longitudinal Surveys of Australian Youth (LSAY) data. The derived variables fall into the categories education, employment and social, and help to simplify the complexity of the LSAY data by providing useful indicators for analysis. To help LSAY data users understand…

  7. Longitudinal Surveys of Australian Youth (LSAY): Derived Variables. Technical Report 64

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2012

    2012-01-01

    This technical report describes the 24 derived variables developed for users of the Longitudinal Surveys of Australian Youth (LSAY) data. The variables fall into the categories education, employment and social, and help to simplify the complexity of the LSAY data by providing useful indicators for analysis. To help LSAY data users understand and…

  8. Career Technical Education Adjunct Faculty Teacher Readiness: An Investigation of Teacher Excellence and Variables of Preparedness

    Science.gov (United States)

    Guerra, Jorge

    2012-01-01

    The purpose of this research was to examine the relationship between teaching readiness and teaching excellence with three variables of preparedness of adjunct professors teaching career technical education courses through student surveys using a correlational design of two statistical techniques; least-squares regression and one-way analysis of…

  9. Variations of Histone Modification Patterns: Contributions of Inter-plant Variability and Technical Factors

    Directory of Open Access Journals (Sweden)

    Sylva Brabencová

    2017-12-01

    Full Text Available Inter-individual variability of conspecific plants is governed by differences in their genetically determined growth and development traits, environmental conditions, and adaptive responses under epigenetic control involving histone post-translational modifications. The apparent variability in histone modifications among plants might be increased by technical variation introduced in sample processing during epigenetic analyses. Thus, to detect true variations in epigenetic histone patterns associated with given factors, the basal variability among samples that is not associated with them must be estimated. To improve knowledge of relative contribution of biological and technical variation, mass spectrometry was used to examine histone modification patterns (acetylation and methylation among Arabidopsis thaliana plants of ecotypes Columbia 0 (Col-0 and Wassilewskija (Ws homogenized by two techniques (grinding in a cryomill or with a mortar and pestle. We found little difference in histone modification profiles between the ecotypes. However, in comparison of the biological and technical components of variability, we found consistently higher inter-individual variability in histone mark levels among Ws plants than among Col-0 plants (grown from seeds collected either from single plants or sets of plants. Thus, more replicates of Ws would be needed for rigorous analysis of epigenetic marks. Regarding technical variability, the cryomill introduced detectably more heterogeneity in the data than the mortar and pestle treatment, but mass spectrometric analyses had minor apparent effects. Our study shows that it is essential to consider inter-sample variance and estimate suitable numbers of biological replicates for statistical analysis for each studied organism when investigating changes in epigenetic histone profiles.

  10. Variations of Histone Modification Patterns: Contributions of Inter-plant Variability and Technical Factors.

    Science.gov (United States)

    Brabencová, Sylva; Ihnatová, Ivana; Potěšil, David; Fojtová, Miloslava; Fajkus, Jiří; Zdráhal, Zbyněk; Lochmanová, Gabriela

    2017-01-01

    Inter-individual variability of conspecific plants is governed by differences in their genetically determined growth and development traits, environmental conditions, and adaptive responses under epigenetic control involving histone post-translational modifications. The apparent variability in histone modifications among plants might be increased by technical variation introduced in sample processing during epigenetic analyses. Thus, to detect true variations in epigenetic histone patterns associated with given factors, the basal variability among samples that is not associated with them must be estimated. To improve knowledge of relative contribution of biological and technical variation, mass spectrometry was used to examine histone modification patterns (acetylation and methylation) among Arabidopsis thaliana plants of ecotypes Columbia 0 (Col-0) and Wassilewskija (Ws) homogenized by two techniques (grinding in a cryomill or with a mortar and pestle). We found little difference in histone modification profiles between the ecotypes. However, in comparison of the biological and technical components of variability, we found consistently higher inter-individual variability in histone mark levels among Ws plants than among Col-0 plants (grown from seeds collected either from single plants or sets of plants). Thus, more replicates of Ws would be needed for rigorous analysis of epigenetic marks. Regarding technical variability, the cryomill introduced detectably more heterogeneity in the data than the mortar and pestle treatment, but mass spectrometric analyses had minor apparent effects. Our study shows that it is essential to consider inter-sample variance and estimate suitable numbers of biological replicates for statistical analysis for each studied organism when investigating changes in epigenetic histone profiles.

  11. Analysis of biological and technical variability in gene expression assays from formalin-fixed paraffin-embedded classical Hodgkin lymphomas.

    Science.gov (United States)

    Vera-Lozada, Gabriela; Scholl, Vanesa; Barros, Mário Henrique M; Sisti, Davide; Guescini, Michele; Stocchi, Vilberto; Stefanoff, Claudio Gustavo; Hassan, Rocio

    2014-12-01

    Formalin-fixed paraffin-embedded (FFPE) tissues are invaluable sources of biological material for research and diagnostic purposes. In this study, we aimed to identify biological and technical variability in RT-qPCR TaqMan® assays performed with FFPE-RNA from lymph nodes of classical Hodgkin lymphoma samples. An ANOVA-nested 6-level design was employed to evaluate BCL2, CASP3, IRF4, LYZ and STAT1 gene expression. The most variable genes were CASP3 (low expression) and LYZ (high expression). Total variability decreased after normalization for all genes, except by LYZ. Genes with moderate and low expression were identified and suffered more the effects of the technical manipulation than high-expression genes. Pre-amplification was shown to introduce significant technical variability, which was partially alleviated by lowering to a half the amount of input RNA. Ct and Cy0 quantification methods, based on cycle-threshold and the kinetic of amplification curves, respectively, were compared. Cy0 method resulted in higher quantification values, leading to the decrease of total variability in CASP3 and LYZ genes. The mean individual noise was 0.45 (0.31 to 0.61 SD), indicating a variation of gene expression over ~1.5 folds from one case to another. We showed that total variability in RT-qPCR from FFPE-RNA is not higher than that reported for fresh complex tissues, and identified gene-, and expression level-sources of biological and technical variability, which can allow better strategies for designing RT-qPCR assays from highly degraded and inhibited samples. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. An Integrated Workflow To Assess Technical and Biological Variability of Cell Population Frequencies in Human Peripheral Blood by Flow Cytometry.

    Science.gov (United States)

    Burel, Julie G; Qian, Yu; Lindestam Arlehamn, Cecilia; Weiskopf, Daniela; Zapardiel-Gonzalo, Jose; Taplitz, Randy; Gilman, Robert H; Saito, Mayuko; de Silva, Aruna D; Vijayanand, Pandurangan; Scheuermann, Richard H; Sette, Alessandro; Peters, Bjoern

    2017-02-15

    In the context of large-scale human system immunology studies, controlling for technical and biological variability is crucial to ensure that experimental data support research conclusions. In this study, we report on a universal workflow to evaluate both technical and biological variation in multiparameter flow cytometry, applied to the development of a 10-color panel to identify all major cell populations and T cell subsets in cryopreserved PBMC. Replicate runs from a control donation and comparison of different gating strategies assessed the technical variability associated with each cell population and permitted the calculation of a quality control score. Applying our panel to a large collection of PBMC samples, we found that most cell populations showed low intraindividual variability over time. In contrast, certain subpopulations such as CD56 T cells and Temra CD4 T cells were associated with high interindividual variability. Age but not gender had a significant effect on the frequency of several populations, with a drastic decrease in naive T cells observed in older donors. Ethnicity also influenced a significant proportion of immune cell population frequencies, emphasizing the need to account for these covariates in immune profiling studies. We also exemplify the usefulness of our workflow by identifying a novel cell-subset signature of latent tuberculosis infection. Thus, our study provides a universal workflow to establish and evaluate any flow cytometry panel in systems immunology studies. Copyright © 2017 by The American Association of Immunologists, Inc.

  13. Technical Stability and Biological Variability in MicroRNAs from Dried Blood Spots: A Lung Cancer Therapy-Monitoring Showcase.

    Science.gov (United States)

    Kahraman, Mustafa; Laufer, Thomas; Backes, Christina; Schrörs, Hannah; Fehlmann, Tobias; Ludwig, Nicole; Kohlhaas, Jochen; Meese, Eckart; Wehler, Thomas; Bals, Robert; Keller, Andreas

    2017-09-01

    Different work flows have been proposed to use miRNAs as blood-borne biomarkers. In particular, the method used for collecting blood from patients can considerably influence the diagnostic results. We explored whether dried blood spots (DBSs) facilitate stable miRNA measurements and compared its technical stability with biological variability. First, we tested the stability of DBS samples by generating from 1 person 18 whole-genome-wide miRNA profiles of DBS samples that were exposed to different temperature and humidity conditions. Second, we investigated technical reproducibility by performing 7 replicates of DBS again from 1 person. Third, we investigated DBS samples from 53 patients with lung cancer undergoing different therapies. Across these 3 stages, 108 genome-wide miRNA profiles from DBS were generated and evaluated biostatistically. In the stability analysis, we observed that temperature and humidity had an overall limited influence on the miRNomes (average correlation between the different conditions of 0.993). Usage of a silica gel slightly diminished DBS' technical reproducibility. The 7 technical replicates had an average correlation of 0.996. The correlation with whole-blood PAXGene miRNomes of the same individual was remarkable (correlation of 0.88). Finally, evaluation of the samples from the 53 patients with lung cancer exposed to different therapies showed that the biological variations exceeded the technical variability significantly ( P technical variations significantly. DBS-based miRNA profiles will potentially further the translational character of miRNA biomarker studies. © 2017 American Association for Clinical Chemistry.

  14. Random Regression Forest Model using Technical Analysis Variables: An application on Turkish Banking Sector in Borsa Istanbul (BIST

    Directory of Open Access Journals (Sweden)

    Senol Emir

    2016-04-01

    Full Text Available The purpose of this study is to explore the importance and ranking of technical analysis variables in Turkish banking sector. Random Forest method is used for determining importance scores of inputs for eight banks in Borsa Istanbul. Then two predictive models utilizing Random Forest (RF and Artificial Neural Networks (ANN are built for predicting BIST-100 index and bank closing prices. Results of the models are compared by three metrics namely Mean Absolute Error (MAE, Mean Square Error (MSE, Median Absolute Error (MedAE. Findings show that moving average (MAV-100 is the most important variable for both BIST -100 index and bank closing prices. Therefore, investors should follow this technical indicator with respect to Turkish banks. In addition ANN shows better performance for all metrics.

  15. Random Regression Forest Model using Technical Analysis Variables: An application on Turkish Banking Sector in Borsa Istanbul (BIST)

    OpenAIRE

    Senol Emir; Hasan Dincer; Umit Hacioglu; Serhat Yuksel

    2016-01-01

    The purpose of this study is to explore the importance and ranking of technical analysis variables in Turkish banking sector. Random Forest method is used for determining importance scores of inputs for eight banks in Borsa Istanbul. Then two predictive models utilizing Random Forest (RF) and Artificial Neural Networks (ANN) are built for predicting BIST-100 index and bank closing prices. Results of the models are compared by three metrics namely Mean Absolute Error (MAE), Mean Square Error (...

  16. Final Technical Report: Low-Cost Solar Variability Sensors for Ubiquitous Deployment.

    Energy Technology Data Exchange (ETDEWEB)

    Lave, Matthew Samuel [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2016-01-01

    In this project, an integrated solution to measuring and collecting solar variability data called the solar variability datalogger (SVD) was developed, tested, and the value of its data to distribution grid integration studies was demonstrated. This work addressed the problem that high-frequency solar variability is rarely measured – due to the high cost and complex installation of existing solar irradiance measuring pyranometers – but is critical to the accurate determination of the impact of photovoltaics to electric grid operation. For example, up to a 300% difference in distribution grid voltage regulator tap change operations (a measure of the impact of PV) [1] has been observed due solely to different solar variability profiles.

  17. Investigation of Students' Attitudes Towards E-Learning in Terms of Different Variables--A Case Study in a Technical and Vocational High School for Girls

    Science.gov (United States)

    Kandil Ingeç, Sebnem

    2015-01-01

    This study aims at determining the attitudes towards e-learning among the students of technical and vocational high school for girls and examining them in terms of certain variables. Singular and relational survey methods were used. The sample consisted of 119 students of technical and vocational high school for girls. Data were collected through…

  18. Influence of variables on the consolidation and unconfined compressive strength of crushed salt: Technical report

    International Nuclear Information System (INIS)

    Pfeifle, T.W.; Senseny, P.E.; Mellegard, K.D.

    1987-01-01

    Eight hydrostatic compression creep tests were performed on crushed salt specimens fabricated from Avery Island dome salt. Following the creep test, each specimen was tested in unconfined compression. The experiments were performed to assess the influence of the following four variables on the consolidation and unconfined strength of crushed salt: grain size distribution, temperature, time, and moisture content. The experiment design comprised a half-fraction factorial matrix at two levels. The levels of each variable investigated were grain size distribution, uniform-graded and well-graded (coefficient of uniformity of 1 and 8); temperature 25 0 C and 100 0 C; time, 3.5 x 10 3 s and 950 x 10 3 s (approximately 60 minutes and 11 days, respectively); and moisture content, dry and wet (85% relative humidity for 24 hours). The hydrostatic creep stress was 10 MPa. The unconfined compression tests were performed at an axial strain rate of 1 x 10 -5 s -1 . Results show that the variables time and moisture content have the greatest influence on creep consolidation, while grain size distribution and, to a somewhat lesser degree, temperature have the greatest influence on total consolidation. Time and moisture content and the confounded two-factor interactions between either grain size distribution and time or temperature and moisture content have the greatest influence on unconfined strength. 7 refs., 7 figs., 11 tabs

  19. Stepwise data envelopment analysis (DEA); choosing variables for measuring technical efficiency in Norwegian electricity distribution

    International Nuclear Information System (INIS)

    Kittelsen, S.A.C.

    1993-04-01

    Electric power distribution is an activity that in principle delivers a separate product to each customer. A specification of products for a utility as a whole leads potentially to a large number of product aspects including topographic and climatic conditions, and the level of disaggregation of factors and products may give the production and cost functions a high dimensionality. Some aggregation is therefore necessary. Non-parametric methods like Data Envelopment Analysis (DEA) have the advantage that they may give meaningful results when parametric methods would not have enough degrees of freedom, but will have related problems if the variables are collinear or are irrelevant. Although aggregate efficiency measures will not be much affected, rates of transformation will be corrupted and observations with extreme values may be measured as efficient by default. Little work has been done so far on the statistical properties of the non-parametric efficiency measure. This paper utilizes a suggestion by Rajiv Banker to measure the significance of the change in results when disaggregating or introducing an extra variable, and shows how one can let the data participate in deciding which variables should be included in the analysis. 32 refs., 7 figs., 4 tabs

  20. Changes in hemp secondary fiber production related to technical fiber variability revealed by light microscopy and attenuated total reflectance Fourier transform infrared spectroscopy.

    Science.gov (United States)

    Fernandez-Tendero, Eva; Day, Arnaud; Legros, Sandrine; Habrant, Anouck; Hawkins, Simon; Chabbert, Brigitte

    2017-01-01

    Interest in hemp (Cannabis sativa L.) is increasing due to the development of a new range of industrial applications based on bast fibers. However the variability of bast fiber yield and quality represents an important barrier to further exploitation. Primary and secondary fiber content was examined in two commercial hemp varieties (Fedora 17, Santhica 27) grown under contrasted sowing density and irrigation conditions. Both growing conditions and hemp varieties impact stem tissue architecture with a large effect on the proportion of secondary fibers but not primary fibers. Attenuated total reflectance infrared spectroscopy allowed the discrimination of manually-isolated native primary fibers and secondary fibers but did not reveal any clustering according to growing conditions and variety. Infrared data were confirmed by wet chemistry analyses that revealed slight but significant differences between primary and secondary fiber cell wall composition. Infrared spectroscopy of technical fibers obtained after mechanical defibering revealed differences with native primary, but not secondary fibers and also discriminated samples obtained from plants grown under different conditions. Altogether the results suggested that the observed variability of hemp technical fibers could be partially explained by i) differences in secondary fiber production and ii) differential behavior during mechanical defibering resulting in unequal separation of primary and secondary fibers.

  1. Technical note: Validation of a semi-automated software tool to determine gait-cycle variables in dairy cows.

    Science.gov (United States)

    Alsaaod, M; Kredel, R; Hofer, B; Steiner, A

    2017-06-01

    This paper presents the validation of a software tool called Cow-Gait-Analyzer (University of Bern, Switzerland) to determine gait-cycle variables in lame and non-lame dairy cows using features derived from low-cost, stand-alone 3-dimensional accelerometers (400 Hz). The Cow-Gait-Analyzer automatically extracts the relevant gait events of foot load and toe off, which characterize gait-cycle duration, stance phase, and swing phase during walking. A nonautomatic step is visual inspection of the pedograms. If the software does not automatically choose the right peaks according to pedogram definitions, peaks can be manually chosen. We validated the algorithms by comparing the accelerometer data (pedogram) with the synchronized video data, which we used as a gold standard. We carried out the measurements at the metatarsal level of paired hind limbs during walking. We included 12 non-lame cows and 5 lame cows and expressed overall differences between the Cow-Gait-Analyzer and the gold standard as relative measurement error (RME). We analyzed 34 hind limbs with a mean of 9 gait cycles. The median RME for gait-cycle duration and stance phases were 0 and 1.69%, respectively. The peaks of gait-cycle variables showed RME of 0.67 and 0.24% for foot load and toe off, respectively. The semi-automated Cow-Gait-Analyzer can accurately determine gait-cycle variables in both lame and non-lame cows, and could be used to assess gait patterns in routine clinical and research practice focusing on individual cows. The Authors. Published by the Federation of Animal Science Societies and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

  2. Technical note: Effects of an epinephrine infusion on eye temperature and heart rate variability in bull calves.

    Science.gov (United States)

    Stewart, M; Webster, J R; Stafford, K J; Schaefer, A L; Verkerk, G A

    2010-11-01

    Changes in autonomic nervous system (ANS) activity are one of the first phases of a stress response, but they are rarely used to assess the welfare of farm animals. Eye temperature measured using infrared thermography (IRT) is proposed as an indicator of ANS activity because it may reflect changes in blood flow in the capillary beds of the conjunctiva. The aim was to determine whether epinephrine infusion would initiate eye temperature changes in calves. Sixteen 4-mo-old Friesian calves (124±5 kg) were assigned randomly to receive a jugular infusion of either epinephrine (4 μg/kg per min for 5 min) or saline. Eye temperature (°C), heart rate (HR), and HR variability (HRV) were recorded from 15 min before infusion until 10 min after it was completed. Blood samples collected via jugular catheter were assayed for epinephrine, norepinephrine, and cortisol concentrations, and packed cell volume (PCV) was measured. No changes in any variable were observed with the saline infusion. Plasma epinephrine concentrations increased 90-fold with epinephrine infusion, which was associated with a decrease in eye temperature of 1.4±0.05°C. During epinephrine infusion, plasma norepinephrine concentrations decreased by half and HR decreased by 9.3±3.3 beats/min. The HRV measure, the root mean square of successive differences, increased by 49.7±9.2 ms, indicating a compensatory increase in parasympathetic activity. After epinephrine infusion, plasma cortisol concentrations increased by 10.4±1.7 ng/mL and PCV was higher (38 vs. 31±0.1%, epinephrine vs. saline, respectively). These results support the hypothesis that changes in eye temperature are mediated by the sympathetic component of the ANS. Infrared thermography is a noninvasive method to assess ANS activity for evaluating welfare of cattle. Copyright © 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  3. Technical Subtopic 2.1: Modeling Variable Refrigerant Flow Heat Pump and Heat Recovery Equipment in EnergyPlus

    Energy Technology Data Exchange (ETDEWEB)

    Raustad, Richard; Nigusse, Bereket; Domitrovic, Ron

    2013-09-30

    The University of Central Florida/Florida Solar Energy Center, in cooperation with the Electric Power Research Institute and several variable-refrigerant-flow heat pump (VRF HP) manufacturers, provided a detailed computer model for a VRF HP system in the United States Department of Energy's (U.S. DOE) EnergyPlus? building energy simulation tool. Detailed laboratory testing and field demonstrations were performed to measure equipment performance and compare this performance to both the manufacturer's data and that predicted by the use of this new model through computer simulation. The project goal was to investigate the complex interactions of VRF HP systems from an HVAC system perspective, and explore the operational characteristics of this HVAC system type within a laboratory and real world building environment. Detailed laboratory testing of this advanced HVAC system provided invaluable performance information which does not currently exist in the form required for proper analysis and modeling. This information will also be useful for developing and/or supporting test standards for VRF HP systems. Field testing VRF HP systems also provided performance and operational information pertaining to installation, system configuration, and operational controls. Information collected from both laboratory and field tests were then used to create and validate the VRF HP system computer model which, in turn, provides architects, engineers, and building owners the confidence necessary to accurately and reliably perform building energy simulations. This new VRF HP model is available in the current public release version of DOE?s EnergyPlus software and can be used to investigate building energy use in both new and existing building stock. The general laboratory testing did not use the AHRI Standard 1230 test procedure and instead used an approach designed to measure the field installed full-load operating performance. This projects test methodology used the air

  4. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

    In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

  5. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

  6. Accumulation and variability of maize pollen deposition on leaves of European Lepidoptera host plants and relation to release rates and deposition determined by standardised technical sampling.

    Science.gov (United States)

    Hofmann, Frieder; Kruse-Plass, Maren; Kuhn, Ulrike; Otto, Mathias; Schlechtriemen, Ulrich; Schröder, Boris; Vögel, Rudolf; Wosniok, Werner

    2016-01-01

    Risk assessment for GMOs such as Bt maize requires detailed data concerning pollen deposition onto non-target host-plant leaves. A field study of pollen on lepidopteran host-plant leaves was therefore undertaken in 2009-2012 in Germany. During the maize flowering period, we used in situ microscopy at a spatial resolution adequate to monitor the feeding behaviour of butterfly larvae. The plant-specific pollen deposition data were supplemented with standardised measurements of pollen release rates and deposition obtained by volumetric pollen monitors and passive samplers. In 2010, we made 5377 measurements of maize pollen deposited onto leaves of maize, nettle, goosefoot, sorrel and blackberry. Overall mean leaf deposition during the flowering period ranged from 54 to 478 n/cm 2 (grains/cm 2 ) depending on plant species and site, while daily mean leaf deposition values were as high as 2710 n/cm 2 . Maximum single leaf-deposition values reached up to 103,000 n/cm 2 , with a 95 % confidence-limit upper boundary of 11,716 n/cm 2 . Daily means and variation of single values uncovered by our detailed measurements are considerably higher than previously assumed. The recorded levels are more than a single degree of magnitude larger than actual EU expert risk assessment assumptions. Because variation and total aggregation of deposited pollen on leaves have been previously underestimated, lepidopteran larvae have actually been subjected to higher and more variable exposure. Higher risks to these organisms must consequently be assumed. Our results imply that risk assessments related to the effects of Bt maize exposure under both realistic cultivation conditions and worst-case scenarios must be revised. Under common cultivation conditions, isolation buffer distances in the kilometre range are recommended rather than the 20-30 m distance defined by the EFSA.

  7. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  8. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  9. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience At the end of the first full-year running period of LHC, CMS is established as a reliable, robust and mature experiment. In particular common systems and infrastructure faults accounted for <0.6 % CMS downtime during LHC pp physics. Technical operation throughout the entire year was rather smooth, the main faults requiring UXC access being sub-detector power systems and rack-cooling turbines. All such problems were corrected during scheduled technical stops, in the shadow of tunnel access needed by the LHC, or in negotiated accesses or access extensions. Nevertheless, the number of necessary accesses to the UXC averaged more than one per week and the technical stops were inevitably packed with work packages, typically 30 being executed within a few days, placing a high load on the coordination and area management teams. It is an appropriate moment for CMS Technical Coordination to thank all those in many CERN departments and in the Collaboration, who were involved in CMS techni...

  10. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience Since the closure of the detector in February, the technical operation of CMS has been quite smooth and reliable. Some minor interventions in UXC were required to cure failures of power supplies, fans, readout boards and rack cooling connections, but all these failures were repaired in scheduled technical stops or parasitically during access dedicated to fixing LHC technical problems. The only occasion when CMS had to request an access between fills was to search for the source of an alarm from the leak-detection cables mounted in the DT racks. After a few minutes of diagnostic search, a leaking air-purge was found. Replacement was complete within 2 hours. This incident demonstrated once more the value of these leak detection cables; the system will be further extended (during the end of year technical stop) to cover more racks in UXC and the floor beneath the detector. The magnet has also been operating reliably and reacted correctly to the 14s power cut on 29 May (see below). In or...

  11. Technical endoscopy

    International Nuclear Information System (INIS)

    Cavalar, K.O.

    1988-01-01

    A survey is provided on different versions of endoscopes, taking into account the new developments of video endoscopy. With a variety of practical examples it is shown that technical tests using endoscopy are a demanding task for nondestructive testing, whose requirements can only be met on a customized basis. (orig./HP) [de

  12. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

  13. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    Overview From a technical perspective, CMS has been in “beam operation” state since 6th November. The detector is fully closed with all components operational and the magnetic field is normally at the nominal 3.8T. The UXC cavern is normally closed with the radiation veto set. Access to UXC is now only possible during downtimes of LHC. Such accesses must be carefully planned, documented and carried out in agreement with CMS Technical Coordination, Experimental Area Management, LHC programme coordination and the CCC. Material flow in and out of UXC is now strictly controlled. Access to USC remains possible at any time, although, for safety reasons, it is necessary to register with the shift crew in the control room before going down.It is obligatory for all material leaving UXC to pass through the underground buffer zone for RP scanning, database entry and appropriate labeling for traceability. Technical coordination (notably Stephane Bally and Christoph Schaefer), the shift crew and run ...

  14. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Switzerland (please sp...

  15. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Swi...

  16. INDOT Technical Training Plan : [Technical Summary

    Science.gov (United States)

    2012-01-01

    A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

  17. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2013-01-01

    For the reporting period, the CMS common systems and infrastructure worked well, without failures that caused significant data losses. One more disconnection of the magnet cold box occurred in the shadow of interruptions in data taking, caused by a series of technical faults. The recognition during 2012 that re-connection can only safely be done at around 2 T implies a minimum magnet recovery time of 12 hours and raises serious concerns about the number of ramping cycles of the magnet these incidents cause. This has triggered studies of how to make the cryo-system of the magnet more robust against failures. The proton-proton run ended just before the end-of-year CERN closure, during which CASTOR was installed on the negative end of CMS and both ZDC calorimeters were installed in TAN absorbers the LHC tunnel, in preparation for the heavy-ion run. The installation of CASTOR was an excellent “engineering test” of procedures for working in an activated environment. Despite some technical pr...

  18. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

      Operational experience 2011 CMS is approaching the end of a very successful year of operation. Proton- proton running ended in the late afternoon of 30th October with a stunning 5.73 fb–1 delivered by LHC, of which CMS recorded 5.22 fb–1. During heavy-ion operation, which continues until 7th December, both the accelerator and the CMS detector have also performed very well. Despite the encouraging overall reliability of technical operation, several infrastructure failures which occurred since the last Bulletin are worthy of mention, with one leading for the first time to significant data-loss. On 10th July, a CERN-wide power failure brought down essentially all services including the magnet, due to an MCS setting being left in “manual” after the recent technical stop, but there was no significant damage and the detector was operational before the LHC, despite a slow and tortuous recovery (one of several indications this year that there is room for improve...

  19. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

  20. Technical presentation

    CERN Multimedia

    FP Department

    2009-01-01

    07 April 2009 Technical presentation by Leuze Electronics: 14.00 – 15.00, Main Building, Room 61-1-017 (Room A) Photoelectric sensors, data identification and transmission systems, image processing systems. We at Leuze Electronics are "the sensor people": we have been specialising in optoelectronic sensors and safety technology for accident prevention for over 40 years. Our dedicated staff are all highly customer oriented. Customers of Leuze Electronics can always rely on one thing – on us! •\tFounded in 1963 •\t740 employees •\t115 MEUR turnover •\t20 subsidiaries •\t3 production facilities in southern Germany Product groups: •\tPhotoelectric sensors •\tIdentification and measurements •\tSafety devices

  1. Technical presentation

    CERN Multimedia

    FI Department

    2008-01-01

    RADIOSPARES, the leading catalogue distributor of components (electronic, electrical, automation, etc.) and industrial supplies will be at CERN on Friday 3 October 2008 (Main Building, Room B, from 9.00 a.m. to 3.00 p.m.) to introduce its new 2008/2009 catalogue. This will be the opportunity for us to present our complete range of products in more detail: 400 000 part numbers available on our web site (Radiospares France, RS International, extended range of components from other manufacturers); our new services: quotations, search for products not included in the catalogue, SBP products (Small Batch Production: packaging in quantities adapted to customers’ requirements); partnership with our focus manufacturers; demonstration of the on-line purchasing tool implemented on our web site in conjunction with CERN. RADIOSPARES will be accompanied by representatives of FLUKE and TYCO ELECTRONICS, who will make presentations, demonstrate materials and answer any technical questio...

  2. Technical presentation

    CERN Multimedia

    GS Department

    2010-01-01

    10 March 2010 DYNEOS 10:00 – 12:00 - Main Building, Room B, 61-1-009 Dyneos AG is active in the fields of photonics, laser and high-precision positioning. Our highly qualified engineer team has more than 30 years of experience in electro-optical solutions sales. The engineers are supported by a technical and administrative team. We are focused on the Swiss market and represent six suppliers (Coherent, PI Physik Instrumente, SIOS, Nanonics Imaging, APE, Ekspla) in order to give a qualified sales and service support to our customers. Our products are dedicated to the research field as well as to industry. In addition to standard catalog products, we offer custom designs to fulfill the specific needs of OEM customers or specific applications.

  3. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2010-01-01

    Overview Once again, the bulk of this article reviews the intense activity of a recently completed shutdown, which, although quite unforeseeable until a few weeks before it started, proved by its success that our often advertised capability to conduct major maintenance within a two month period is real. Although safely completed, on-time to remarkable precision, the activity was not without incident, and highlighted our dependence on many experienced, specialist teams and their precise choreography. Even after the yoke was safely closed, magnet re-commissioning and beampipe pumpdown showed new and thought-provoking behaviour. The struggle to maintain adequate technical resources will be a pre-occupation over the coming months, in parallel with the start of truly sustained operation, for which various procedures are still being put in place. Planning for future shutdowns must now become a high priority, with many working groups and task forces already in existence to prepare infrastructure improvements and to...

  4. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Tuesday 3 February 2004 From 09:00 to 13:30 - Training Centre Auditorium - bldg. 593, room 11 USB (Universal Serial Bus) CYPRESS Seminar Claudia Colombini, Field Application Engineer CYPRESS ActiveComp Electronic GmbH D-85077 MANCHING, Germany As a pioneer in USB, CYPRESS sets the standard for cost-effective solutions without sacrificing functionality, performance or reliability. Having shipped over 200 million USB devices, Cypress is the undisputed market leader and demonstrates unmatched USB expertise. With the industry's broadest selection of USB solutions, Cypress has the right silicon, software and support for every USB application, from Low-speed to High-Speed and USB On-The-Go (OTG). 9:00 - 10:30 Overview of USB systems. USB CYPRESS product overview. Peripherals: Low Speed, Full Speed, High Speed (1.1 and 2.0). Hub Solutions, Embedded Host Solutions, On-The-Go (OTG) and wireless USB. USB Development Tools (first part) 10:30 -...

  5. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2012-01-01

      UXC + detectors As explained in detail in the November 2011 bulletin, the bellows unit at −18.5 m from the CMS interaction point was identified as a prime candidate for the regularly occurring pressure spikes which occasionally led to sustained severe background conditions in 2011, affecting dead time and data quality. Similar regions in LHC with vacuum instabilities were observed to be close to bellows, which radiography showed to have distorted RF-fingers — on removal, they proved to have been severely overheated. The plans for the Year-End Technical Stop were adapted to prioritise radiography of the bellows at 16 m to 18 m either end of CMS. Excellent work by the beam pipe, survey and heavy mechanical teams allowed the X-rays to be taken as planned on 20th December, showing that the bellow at −18.5m had an obvious non-conformity. The RF-fingers were found inside the end of the opposing flared pipe instead of outside. In addition, the overlap between fingers and...

  6. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  7. Technical innovation and management

    International Nuclear Information System (INIS)

    Yoon, Yang Cheol

    1982-08-01

    This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.

  8. Strategy of technical innovation

    International Nuclear Information System (INIS)

    Lee, Ga Jong

    1990-12-01

    This book deals with policy of scientific technique and technical innovation such as research for development and types of technical innovation, historical development and process of technical innovation, economic growth, technology change and investment for research and development, structure and form of technical transfer with the meaning process, from, structure and theory, economic growth and investment of research and development with experiential analysis and case study on strategy of technical innovation in electron and fine chemical industry.

  9. Impact of Climate Change on the Technical Efficiency of Striped Catfish, Pangasianodon hypophthalmus, Farming in the Mekong Delta, Vietnam

    NARCIS (Netherlands)

    Nguyen, L.A.; Pham, Tung B.V.; Bosma, R.H.; Verreth, J.A.J.; Leemans, H.B.J.; Silva, De Sena; Oude Lansink, A.G.J.M.

    2017-01-01

    The technical efficiency of randomly sampled pangasius farms in the Mekong Delta of Vietnam was estimated using data envelopment analysis, and factors affecting technical and scale efficiency were examined with bootstrap truncated regression. The mean technical efficiency score assuming variable

  10. Technical efficiency, efficiency change, technical progress and ...

    African Journals Online (AJOL)

    Technical efficiency, efficiency change, technical progress and productivity growth in the national health systems of continental African countries. ... a view to analysing changes in efficiency and changes in technology. The analysis was based on a five-year panel data (1999-2003) from all the 53 countries of continental ...

  11. Technical training: places available

    CERN Multimedia

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  12. Technical training - places available

    CERN Multimedia

    2013-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  13. Technical training: places available

    CERN Multimedia

    2014-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Marie Lahchimi, Technical Training Administration (Tel: 74924)

  14. Technical training: places available

    CERN Multimedia

    2014-01-01

    If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

  15. Technical training: places available

    CERN Multimedia

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tél : 74924)  

  16. Technical Assistance Plan (TAP)

    Science.gov (United States)

    A Technical Assistance Plan (TAP) enables community groups to retain the services of an independent technical advisor and to provide resources for a community group to help inform other community members about site decisions.

  17. Biasogram: visualization of confounding technical bias in gene expression data

    DEFF Research Database (Denmark)

    Krzystanek, Marcin; Szallasi, Zoltan Imre; Eklund, Aron Charles

    2013-01-01

    Gene expression profiles of clinical cohorts can be used to identify genes that are correlated with a clinical variable of interest such as patient outcome or response to a particular drug. However, expression measurements are susceptible to technical bias caused by variation in extraneous factors...... such as RNA quality and array hybridization conditions. If such technical bias is correlated with the clinical variable of interest, the likelihood of identifying false positive genes is increased. Here we describe a method to visualize an expression matrix as a projection of all genes onto a plane defined...... by a clinical variable and a technical nuisance variable. The resulting plot indicates the extent to which each gene is correlated with the clinical variable or the technical variable. We demonstrate this method by applying it to three clinical trial microarray data sets, one of which identified genes that may...

  18. Teaching Technical Writing - Towards Technical Writing

    DEFF Research Database (Denmark)

    Kastberg, Peter

    2000-01-01

    In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm...... that used to govern what the quality of an LSP text should be as opposed to the standpoint, which I advocate. By way of summing up, I will show how a university curriculum is designed so that - upon graduation - the technical translator could also be methodological quite well suited to take on the challenge...... of technical writing....

  19. Variability Bugs:

    DEFF Research Database (Denmark)

    Melo, Jean

    Many modern software systems are highly configurable. They embrace variability to increase adaptability and to lower cost. To implement configurable software, developers often use the C preprocessor (CPP), which is a well-known technique, mainly in industry, to deal with variability in code....... Although many researchers suggest that preprocessor-based variability amplifies maintenance problems, there is little to no hard evidence on how actually variability affects programs and programmers. Specifically, how does variability affect programmers during maintenance tasks (bug finding in particular...... be exploited. Variability bugs are not confined to any particular type of bug, error-prone feature, or location. In addition to introducing an exponential number of program variants, variability increases the complexity of bugs due to unintended feature interactions, hidden features, combinations of layers...

  20. Progress report : Technical Physics Division

    International Nuclear Information System (INIS)

    Gopalaraman, C.P.; Deshpande, R.Y.

    1978-01-01

    The research and development work carried out in the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, is reported. Some of the achievements are: (1) fabrication of mass spectrometers for heavy water analysis and lithium 6/7 isotope ratio measurement, (2) fabrication of electronic components for mass spectrometers, (3) growing of sodium iodide crystals for radiation detectors, (4) development of sandwich detectors comprising of NaI(Tl) and CaI(Na), (5) fabrication of mass spectrometer type leak detectors and (6) fabrication of the high vacuum components of the vacuum system of the variable energy cyclotron based at Calcutta. (M.G.B.)

  1. Nucleoelectric plants technical memory

    International Nuclear Information System (INIS)

    Araujo Pereira, Alvaro de

    1991-01-01

    The work explains the basic norms that establish the guidelines to the Technical Memory elaboration of this electrical energy sector - the nucleoelectric plants. It guides the technicians who execute the Technical Memory of the plants, exposing the items that may compose the work: contents: introduction, planning, proposition, equipment and materials supply, construction, commissioning, commercial actions, budget, financing and costs; generalities: drawings and photographies, monetary references, terminology, system units, management, graphic guide project, responsible staff, a summarized technical card and illustrations

  2. Final Technical Report for DOE Award DE-FG02-07ER64403 [Modeling of Microbially Induced Calcite Precipitation for the Immobilization of Strontium-90 Using a Variable Velocity Streamtube Ensemble

    Energy Technology Data Exchange (ETDEWEB)

    Ginn, Timothy R. [University of California, Davis; Weathers, Tess [University of California, Davis

    2013-08-26

    Biogeochemical modeling using PHREEQC2 and a streamtube ensemble approach is utilized to understand a well-to-well subsurface treatment system at the Vadose Zone Research Park (VZRP) near Idaho Falls, Idaho. Treatment involves in situ microbially-mediated ureolysis to induce calcite precipitation for the immobilization of strontium-90. PHREEQC2 is utilized to model the kinetically-controlled ureolysis and consequent calcite precipitation. Reaction kinetics, equilibrium phases, and cation exchange are used within PHREEQC2 to track pH and levels of calcium, ammonium, urea, and calcite precipitation over time, within a series of one-dimensional advective-dispersive transport paths creating a streamtube ensemble representation of the well-to-well transport. An understanding of the impact of physical heterogeneities within this radial flowfield is critical for remediation design; we address this via the streamtube approach: instead of depicting spatial extents of solutes in the subsurface we focus on their arrival distribution at the control well(s). Traditionally, each streamtube maintains uniform velocity; however in radial flow in homogeneous media, the velocity within any given streamtube is spatially-variable in a common way, being highest at the input and output wells and approaching a minimum at the midpoint between the wells. This idealized velocity variability is of significance in the case of ureolytically driven calcite precipitation. Streamtube velocity patterns for any particular configuration of injection and withdrawal wells are available as explicit calculations from potential theory, and also from particle tracking programs. To approximate the actual spatial distribution of velocity along streamtubes, we assume idealized radial non-uniform velocity associated with homogeneous media. This is implemented in PHREEQC2 via a non-uniform spatial discretization within each streamtube that honors both the streamtube’s travel time and the idealized

  3. Pulsating variables

    International Nuclear Information System (INIS)

    1989-01-01

    The study of stellar pulsations is a major route to the understanding of stellar structure and evolution. At the South African Astronomical Observatory (SAAO) the following stellar pulsation studies were undertaken: rapidly oscillating Ap stars; solar-like oscillations in stars; 8-Scuti type variability in a classical Am star; Beta Cephei variables; a pulsating white dwarf and its companion; RR Lyrae variables and galactic Cepheids. 4 figs

  4. Efeito do uso do traje de neoprene sobre variáveis técnicas, fisiológicas e perceptivas de nadadores Effects of a neoprene suit over technical, physiological and perceptive variables of swimmers

    Directory of Open Access Journals (Sweden)

    Karini Borges dos Santos

    2011-06-01

    Full Text Available Ao contrário do que ocorre em provas de piscina, competições em águas abertas estão sujeitas as condições ambientais, sendo uma delas as baixas temperaturas. Em determinadas circunstâncias é permitido o uso de roupas especiais para evitar hipotermia. O objetivo do estudo foi verificar os efeitos do uso da roupa de neoprene em um grupo composto por triatletas e nadadores, comparado ao uso de vestimentas convencionais (sunga sobre variáveis cinemáticas e psicofisiológicas do nado. Participaram 20 homens (12 triatletas e oito nadadores de idade 22,0 ± 6,6 anos com desempenhos que correspondem a 75 ± 7,7% do melhor tempo brasileiro na prova de 400 m. Os atletas realizaram duas repetições máximas e duas submáximas de 400 m em nado "crawl", com e sem o uso da roupa de neoprene. Foram comparadas a velocidade média (VM, comprimento de braçada (CB, frequência de braçada (FB, índice de nado (IN, percepção subjetiva de esforço (PSE, frequência cardíaca (FC, e concentração de lactato sanguíneo (LAC. Um conjunto de ANOVAs com medidas repetidas do tipo "two-way" foi aplicado. Quando diferenças foram encontradas o teste de Tukey foi empregado. Com o traje de neoprene, em máxima intensidade, o tempo para nadar a distância foi 6,4% menor, com manutenção da FB e aumento da CB, as variáveis psicofisiológicas não diferiram estatisticamente. Em esforço submáximo, o uso do traje de neoprene resultou em menor FB, maior CB, maior IN e em menores valores de FC, LAC e PSE (p In open water swimming competitions, athletes are prone to environmental conditions and are frequently exposed to low temperatures, in contrast to what occurs in indoor competitions. In some circumstances the use of special swimming suits is allowed to avoid hypothermia. The aim of this study was to verify the effects of the use of a neoprene swimming suit in comparison to a conventional swimming suit on a number of cinematic and psychophysiological variables

  5. Cognitive Variability

    Science.gov (United States)

    Siegler, Robert S.

    2007-01-01

    Children's thinking is highly variable at every level of analysis, from neural and associative levels to the level of strategies, theories, and other aspects of high-level cognition. This variability exists within people as well as between them; individual children often rely on different strategies or representations on closely related problems…

  6. Technical Manual. The ACT®

    Science.gov (United States)

    ACT, Inc., 2014

    2014-01-01

    This manual contains technical information about the ACT® college readiness assessment. The principal purpose of this manual is to document the technical characteristics of the ACT in light of its intended purposes. ACT regularly conducts research as part of the ongoing formative evaluation of its programs. The research is intended to ensure that…

  7. TRANSLATING SERVICE TECHNICAL PROSE

    African Journals Online (AJOL)

    of technical literature: advertising agencies dealing with clients in the technical fields, workshops ..... editing, a subject specialist. (preferably a physician au fait with aerospace matters), and two good translators. Having all the resources at hand, the teams seclude themselves with all their allocated documents and the senior.

  8. Developing Technical Skill Assessments

    Science.gov (United States)

    Hyslop, Alisha

    2009-01-01

    One of the biggest challenges facing the career and technical education (CTE) community as it works to implement the 2006 Perkins Act is responding to more rigorous requirements for reporting on CTE students' technical skill attainment. The U.S. Department of Education suggested in non-regulatory guidance that states and locals use the number of…

  9. Summer Technical Students 2004

    CERN Multimedia

    Maximilien Brice

    2004-01-01

    About 100 technical and doctoral students arrive each year, undergraduates and post-graduates who are preparing diploma or doctoral theses in applied science and technology. They spend up to two years at the Laboratory, as technical students as part of their formal training for a recognised degree or its equivalent.

  10. Transformation of technical infrastructure

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev

    1998-01-01

    article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply.......article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply....

  11. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Glasser, Alan H. [Fusion Theory and Computation Inc., Kingston, WA (United States)

    2018-02-02

    Final technical report on DE-SC0016106. This is the final technical report for a portion of the multi-institutional CEMM project. This report is centered around 3 publications and a seminar presentation, which have been submitted to E-Link.

  12. Technical Training for Managers.

    Science.gov (United States)

    Haverland, Edgar M.

    The question has arisen as to what kind of information a manager without extensive technical training needs to learn to supervise effectively. For example, the Nike Hercules fire control platoon leader, usually an officer in his first active duty assignment, seldom has had extensive technical training. Yet he is responsibile for the…

  13. Technical Agency in Practice

    DEFF Research Database (Denmark)

    Krummheuer, Antonia Lina

    2015-01-01

    ) description of hybrid networks in which human and non-human actants are granted agency without differentiating different kinds of agency, EMCA focuses on the member's perspectives and the situated construction of technical agency that is made relevant within an ongoing interaction. Based on an EMCA analysis......The paper combines the discussion of technical agency and hybrid networks of Actor-Network Theory (ANT) with an ethnomethodological/conversation analytical (EMCA) perspective on situated practices in which participants ascribe agency to technical artefacts. While ANT works with (ethnographic...... of three video recordings of situations in which technical agency is made relevant by the human participants, the paper demonstrates different ways in which agency is granted to technical artefacts. Human participants can treat a technology as communication partner, as an active part (and actant...

  14. The Consolidated Human Activity Database — Master Version (CHAD-Master) Technical Memorandum

    Science.gov (United States)

    This technical memorandum contains information about the Consolidated Human Activity Database -- Master version, including CHAD contents, inventory of variables: Questionnaire files and Event files, CHAD codes, and references.

  15. Comprobación de las variables de estado de diagnóstico para determinar el estado técnico o condición de inyección de una instalación motriz diésel; Confirmation of the Variables of Diagnosis State to Determinate the Technical State or Condition of the Inj

    Directory of Open Access Journals (Sweden)

    Luis García Abreu

    2011-02-01

    Full Text Available Se presenta un análisis desde el punto de vista experimental de las variables de estado de diagnóstico (opacidadde los gases, temperatura de los gases de escape y consumo de combustible para determinar el estado técnicoo condición del aparato de inyección de una instalación motriz diésel. Presently article is carried out an analysis from the experimental point of view of the variables of diagnosis state(opacity of the gases, temperatura of the gases of the escape, consumption of fuel for the determination of thetechnical state or condition the injection apparatus of a diesel motive installation.

  16. Technical standards in nuclear area

    International Nuclear Information System (INIS)

    Grimberg, M.

    1978-01-01

    The technical standardization in nuclear area is discussed. Also, the competence of CNEN in standardization pursuit is analysed. Moreover, the process of working up of technical standards is explained; in addition, some kinds of technical standards are discussed. (author) [pt

  17. Technical Report Writing Today

    DEFF Research Database (Denmark)

    Riordan, Daniel G.

    2014-01-01

    Section 1: Technical Communication Basics (8 chapters on tech com, audiences, tech com process, tech com style, researching, designing pages, using visual aids, describing). Section 2: Technical Communication Applications (7 chapters on sets of instructions, informal reports and email, developing...... websites/using social media, formal reports, recommendation and feasibility reports, proposals, user manuals). Section 3: Professional Communication (2 chapters and 2 appendices on presentations, job application materials, brief handbook for tech writers, documenting sources).......Section 1: Technical Communication Basics (8 chapters on tech com, audiences, tech com process, tech com style, researching, designing pages, using visual aids, describing). Section 2: Technical Communication Applications (7 chapters on sets of instructions, informal reports and email, developing...

  18. OSH technical reference manual

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  19. Superfund Technical Assistance Grants

    Data.gov (United States)

    U.S. Environmental Protection Agency — This asset includes data related to the Superfund Technical Assistance Grant program, including grant number, award amounts, award dates, period of performance,...

  20. Applying technical versatility

    Energy Technology Data Exchange (ETDEWEB)

    None

    1970-01-01

    The breadth and depth of the diversified technical programs at Mound Laboratory since its inception are characterized by a record of competence and versatility during the past generation. A spectrum of mission assignments has been completed successfully in such diverse technical areas as process development and manufacturing of explosive components, research on fuels for the Civilian Power Reactor Program, separation of radioactive materials, fabrication of radioisotopic heat sources, stable gaseous isotope separation and purification, and many other areas. Mound Laboratory is one of the key U.S. Atomic Energy Commission sites that has demonstrated its technical competence in both weapons and non-weapons activities. This report has been prepared to complement the AEC’s vigorous program of scientific information dissemination. Three broad areas of technical competence are highlighted here: explosive technology, radionuclide technology, and stable gaseous isotope separation, which encompass a broad variety of techniques and supporting disciplines.

  1. Technical report writing today

    CERN Document Server

    Riordan, Daniel G

    2014-01-01

    "Technical Report Writing Today" provides thorough coverage of technical writing basics, techniques, and applications. Through a practical focus with varied examples and exercises, students internalize the skills necessary to produce clear and effective documents and reports. Project worksheets help students organize their thoughts and prepare for assignments, and focus boxes highlight key information and recent developments in technical communication. Extensive individual and collaborative exercises expose students to different kinds of technical writing problems and solutions. Annotated student examples - more than 100 in all - illustrate different writing styles and approaches to problems. Numerous short and long examples throughout the text demonstrate solutions for handling writing assignments in current career situations. The four-color artwork in the chapter on creating visuals keeps pace with contemporary workplace capabilities. The Tenth Edition offers the latest information on using electronic resum...

  2. Socio-technical Betwixtness

    DEFF Research Database (Denmark)

    Bossen, Claus

    2017-01-01

    the intrinsically social and technical interwovenness of design, and the necessity of including affected people and stakeholders in the design process. This betwixtness of socio-technical design is demonstrated by the analysis of two IT systems for healthcare: a foundational model for electronic healthcare records......This chapter focusses on two challenges for socio-technical design: Having to choose between different rationales for design, and the adequate understanding and depiction of the work to be redesigned. These two challenges betwixt the otherwise strong tenets of socio-technical design of pointing out......, and an IT system organizing hospital porters’ work. The conceptual background for the analysis of the cases is provided by a short introduction to different rationales for organizational design, and by pointing to the differences between a linear, rationalistic versus an interactional depiction of work....

  3. Science and Technical Indicators

    Czech Academy of Sciences Publication Activity Database

    Laiblová Kadlecová, Ivana; Lhoták, Martin; Mika, Pavel

    -, č. 3 (2014) E-ISSN 1805-2800 Keywords : bibliometrics Subject RIV: AF - Documentation, Lib rarianship, Information Studies http://www. lib .cas.cz/casopis-informace/science-and-technical-indicators/

  4. NCDC Technical Reports

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCDC Technical Reports is a set of retrospective analyses produced by the Research Customer Service Group and the National Climatic Data Center from 1995 to 2008....

  5. Retention of technical professionals

    OpenAIRE

    2012-01-01

    M.Ing. The loss of skills and knowledge of technical professionals experienced by many organizations in South Africa has serious implications on the competitiveness of these organizations in the local and international markets. Organizations should come to realize that they should find creative ways to retain critical skills and knowledge and ensure continuity in terms of succession management. Technical professionals play a crucial role in society. They are responsible for maintaining the...

  6. Understanding Socio Technical Modularity

    DEFF Research Database (Denmark)

    Thuesen, Christian Langhoff; Kudsk, Anders; Hvam, Lars

    2011-01-01

    dimension of modularity like irrational behaviors, cultural differences, learning processes, social organization and institutional influences on modularity. The paper addresses this gab offering a reinterpretation of the modularity concept from a socio-technical perspective in general and Actor Network...... Theory in particular. By formulating modularity from an ANT perspective covering social, material and process aspects, the modularity of a socio-technical system can be understood as an entanglement of product, process, organizational and institutional modularity. The theoretical framework is illustrated...

  7. Utilization technique on variable speed device

    International Nuclear Information System (INIS)

    1989-12-01

    This reports of workshop on power technology describes using technique on variable speed device, which deals with alternating current situation and prospect of current variable speed device, technical trend and prospect of electronics, reduce expenses by variable speed device, control technique, measurement technology, high voltage variable speed device, recent trend of inverter technology, low voltage and high voltage variable speed device control device, operating variable speed device in cooling fan, FDF application and defect case of variable speed device, cooling pump application of water variable transformer, inverter application and energy effect of ventilation equipment, application of variable speed device and analysis of the result of operation and study for application of variable speed technology.

  8. Complex variables

    CERN Document Server

    Fisher, Stephen D

    1999-01-01

    The most important topics in the theory and application of complex variables receive a thorough, coherent treatment in this introductory text. Intended for undergraduates or graduate students in science, mathematics, and engineering, this volume features hundreds of solved examples, exercises, and applications designed to foster a complete understanding of complex variables as well as an appreciation of their mathematical beauty and elegance. Prerequisites are minimal; a three-semester course in calculus will suffice to prepare students for discussions of these topics: the complex plane, basic

  9. Technical Efficiency of Palm Oil Production in West Kalimantan

    Directory of Open Access Journals (Sweden)

    Ismiasih Ismiasih

    2018-01-01

    Full Text Available This research aims to analyze the technical efficiency and source of technical inefficiency of palm oil production. The data used are secondary data from agricultural census survey in 2013 with a sample of 1229 farmer. Technical efficiency is measured by using stochastic frontier production function and is estimated using MLE method assuming that Cobb-Doughlas is the functional form of palm oil. From the research result, it is known that the factors that influence the technical efficiency of palm oil production in West Kalimantan Province are a number of productive trees, plant age, urea fertilizer, SP36, NPK, labor and dummy pesticide. Furthermore, variables of the percentage of own capital, membership of cooperative and membership of contract farming are influencing to reduce technical inefficiency. Therefore, efforts to improve the technical efficiency is to increase the role of the cooperative to its members, and increase the involvement of palm oil farmers in the plasma pattern.

  10. Technical Teachers and Technical Teacher Education - Research Results

    Directory of Open Access Journals (Sweden)

    D. Dobrovská

    2002-01-01

    Full Text Available Chartered engineers who are new teachers of technical subjects at various educational institutions receive technical teacher education in the accredited bachelor programme at the Czech Technical University in Prague. This paper presents the results of a recent survey in which engineers expressed their opinions on technical teacher education.

  11. Lithiasis size estimation variability depending on image technical methodology.

    Science.gov (United States)

    Argüelles Salido, Enrique; Aguilar García, Jesús; Lozano-Blasco, Jose María; Subirá Rios, Jorge; Beardo Villar, Pastora; Campoy-Martínez, Pedro; Medina-López, Rafael A

    2013-11-01

    The lithiasic size is a determining factor in selecting the most suitable treatment, surgical or medical. However, the method for obtaining a reliable lithiasic size is not standardized. Our objetives are to determine the differences between the estimated lithiasic sizes shown by plain radiography test and by computerized axial tomography (CT) scan (using different techniques) in relation to the actual size, and to establish which is the ideal type of imaging for this purpose. We present an in vitro model with lithiasis obtained in cooperation with four centers. lithiasis >0.5 cm, intact, and visible via simple radiography. A sample of 245 lithiases was obtained, with 87 rejected as they did not fulfill the inclusion criteria. Initially the three main actual diameters of each lithiasis were measured with a calibrator, then a plain X-ray and a CT scan were taken of the samples to determine the surface size in cm(2) for simple radiography; surface size and volume in cm(3) for CT scan, in bone window and soft tissue (Toshiba Aquillion 64, sections of 0.5 mm, 120 Kv, 250 mA). The tomographic area was calculated by employing the formula recommended by the European Association of Urology and scanner software. The actual, radiographic and tomographic measurements were taken by three different researchers who were unaware of the results obtained by the each other. The statistics program IBM SPSS Statistics(®) 19 was used. Differences were analyzed using the Wilcoxon sign test. The bone window CT scan slightly overestimated the actual lithiasic size (0.12 vs. 0.17 cm(3)), while in soft tissue window the actual volume was practically doubled (0.12 vs. 0.21 cm(3)) (p lithiasis measurements can be estimated, although the craniocaudal diameter measurement will be overestimated. Using soft tissue window gives an overestimated size.

  12. Technical training: places available

    CERN Multimedia

    2013-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Introduction to VHDL 21-Feb-13 to 22-Feb-13 2 days English Mechanical design Next Session Duration Language ANSYS - Introduction à ANSYS Mechanical APDL 04-Feb-13 to 07-Feb-13 4 days English Applications de la cotation fonctionnelle et du langage ISO 06-Feb-13 to 08-Feb-13 2 days 4 hours French CATIA V5 – Surfacique 14-Jan-13 to 15-Jan-13 2 days French Office software Next Session Duration Language ACCESS 2010 - niveau 2 : ECDL 06-Feb-13 to 07-Feb-13 2 days French Dreamweaver CS3 - Niveau 1 14-Jan-13 to 15-Jan-13 2 d...

  13. Technical training - Places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Availability Certified LabVIEW Associate Developer (CLAD) 06-Dec-12 to 06-Dec-12 1 hour English One more place available Compatibilité électromagnetique (CEM): Applications 23-Nov-12 to 23-Nov-12 3.5 hours English 3 places available Compatibilité électromagnétique (CEM): Introduction 23-Nov-12 to 23-Nov-12 3 hours English 43 places available Effets des Radiations sur les composants et systèmes électroniques 11-Dec-12 to 12-Dec-12 1 day 4 hours French 9 places available LabVIEW for beginners ...

  14. Windows 10 Technical Preview

    OpenAIRE

    Jyväsjärvi, Teppo

    2015-01-01

    Tässä opinnäytetyössä tutustaan uuden kesällä 2015 virallisesti julkaistavan Windows 10 -käyttöjärjestelmän Technical Preview -kehitysversioon. Ensimmäinen Technical Preview -versio julkaistiin syksyllä 2014. Opinnäytetyössä tutustaan Windows 10:n uusin ominaisuuksiin ja tehdään vertailua aiemman Windows 8.1 -version kanssa. Työssä Windows 10 Technical Preview asennetaan virtuaalikoneelle, käydään läpi asennuksen eri vaiheet sekä suurimmat muutokset käyttöliittymässä ja sovelluksissa. Op...

  15. Technical training - places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department »Electronics design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 3 places available Foundations of Electromagnetism and Magnet Design (EMAG) 14-Nov-12 to 27-Nov-12 6 days English 20 places available Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 15 places available Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 7 places available LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places available »Mechanical design Next Se...

  16. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  17. Technical memory 2007

    International Nuclear Information System (INIS)

    2009-01-01

    The technical memory 2007 of the Nuclear Regulatory Authority (ARN) of the Argentine Republic, compiles the papers published in the subject on radiation protection and nuclear safety, and presented in journals, technical reports, congress or meetings of these specialities by personnel of the mentioned institution during 2007. In this edition the documents are presented on: environmental protection; transport of radioactive materials; regulations; research reactors and nuclear power plants; biological radiation effects; therapeutic uses of ionizing radiation and radioprotection of patients; internal dosimetry; physical dosimetry; knowledge management; radioactive waste management [es

  18. Transformation of technical infrastructure

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev

    , the evolution of large technological systems and theories about organisational and technological transformationprocesses. The empirical work consist of three analysis at three different levels: socio-technical descriptions of each sector, an envestigation of one municipality and envestigations of one workshop......The scope of the project is to investigate the possibillities of - and the barriers for a transformation of technical infrastructure conserning energy, water and waste. It focus on urban ecology as a transformation strategy. The theoretical background of the project is theories about infrastructure...

  19. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    You are running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  20. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2009-01-01

    Are you running Vista on your new PC – or are you planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual session of this course will take place on 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  1. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    You are running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced using Windows XP. The next bilingual sessions of this course will take place on December 12, 2008 and January 30, 2009. Register using our catalogue : http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at Technical.Training@cern.ch

  2. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    Are you running Vista on your new PC – or are you planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at mailto:Technical.Training@cern.ch

  3. CERN Technical Training : Vista !

    CERN Multimedia

    HR Department

    2008-01-01

    Are you running Vista on your new PC – or are planning to install it? The Technical Training service is organizing a half-day training course on the new features of the VISTA operating system. This course introduces the new interfaces and presents the new functionalities for people who are experienced in the use of Windows XP. The next bilingual sessions of this course will take place on 12 December 2008 and 30 January 2009. Register using our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your questions/comments at Technical.Training@cern.ch

  4. Technical Writing in Hydrogeology.

    Science.gov (United States)

    Tinker, John R., Jr.

    1986-01-01

    A project for Writing Across the Curriculum at the University of Wisconsin-Eau Claire is described as a method to relate the process of writing to the process of learning hydrology. The project focuses on an actual groundwater contamination case and is designed to improve the technical writing skills of students. (JN)

  5. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) IT3T/1 - Read your mail and more with Outlook 2003 : 14.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/2 - Creating, managing and using distribution lists with Simba2 : 16.6.2005 (IT Technical Training Tutorial, free of charge) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP : 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003 : 30.6.2005 (IT Technical Training Tutorial, free of charge) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoC...

  6. Technical objectives of inspection

    International Nuclear Information System (INIS)

    Sorenson, R.J.; Stewart, K.B.; Schneider, R.A.

    1976-01-01

    The various technical objectives of inspection are discussed in a very general manner. The discussion includes how the inspection function is related to the assumed threat, the various degrees of assurance and reliance on criteria, and the hierarchy of assurance which is obtained from the various types or levels of inspection

  7. Technical basis of safeguards

    International Nuclear Information System (INIS)

    Buechler, C.

    1975-01-01

    Definition of nuclear materials control. Materials accountancy and physical control as technical possibilities. Legal possibilities and levels of responsibility: material holders, national and international authority. Detection vs. prevention. Physical security and containment surveillance. Accountancy: materials balance concept. Materials measurement: inventory taking, flow determination. IAEA safeguards; verification of operator's statement. (HP) [de

  8. ITER EDA technical activities

    International Nuclear Information System (INIS)

    Aymar, R.

    1998-01-01

    Six years of technical work under the ITER EDA Agreement have resulted in a design which constitutes a complete description of the ITER device and of its auxiliary systems and facilities. The ITER Council commented that the Final Design Report provides the first comprehensive design of a fusion reactor based on well established physics and technology

  9. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Migration 6 to 7: 14.6.2005 (1 day) IT3T/1 - Read your mail and more with Outlook 2003 : 14.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/2 - Creating, managing and using distribution lists with Simba2 : 16.6.2005 (IT Technical Training Tutorial, free of charge) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) size="2">(1journée) Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Shor...

  10. Final technical report

    DEFF Research Database (Denmark)

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    This project entails research with the goal to extend laser cutting of steel based metals to thickness above 20 mm and laser powers in the 10 kW range, with adequate accuracy and economically viable cutting speeds. The technical approach is to develop mirror based cutting heads with truly coaxial...

  11. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    John Ross

    2003-04-30

    The Final Technical Report summarizes research accomplishments and Publications in the period of 5/1/99 to 4/30/03 done on the grant. Extensive progress was made in the period covered by this report in the areas of chemical kinetics of non-linear systems; spatial structures, reaction - diffusion systems, and thermodynamic and stochastic theory of electrochemical and general systems.

  12. MCFire model technical description

    Science.gov (United States)

    David R. Conklin; James M. Lenihan; Dominique Bachelet; Ronald P. Neilson; John B. Kim

    2016-01-01

    MCFire is a computer program that simulates the occurrence and effects of wildfire on natural vegetation, as a submodel within the MC1 dynamic global vegetation model. This report is a technical description of the algorithms and parameter values used in MCFire, intended to encapsulate its design and features a higher level that is more conceptual than the level...

  13. Final Technical Report

    International Development Research Centre (IDRC) Digital Library (Canada)

    Tommy Ngai

    2014-03-31

    Mar 31, 2014 ... capacity building activities) to upgrade the technical and management capacities of governments ..... Elements of evaluation are required throughout the chain of activities in order to undertake a ...... Department of Water Supply and Sewerage Pokhara, Pokhara Engineering College, Choice Nepal, and.

  14. PISA 2009 Technical Report

    Science.gov (United States)

    OECD Publishing (NJ1), 2012

    2012-01-01

    The "PISA 2009 Technical Report" describes the methodology underlying the PISA 2009 survey. It examines additional features related to the implementation of the project at a level of detail that allows researchers to understand and replicate its analyses. The reader will find a wealth of information on the test and sample design,…

  15. PISA 2012 Technical Report

    Science.gov (United States)

    OECD Publishing, 2014

    2014-01-01

    The "PISA 2012 Technical Report" describes the methodology underlying the PISA 2012 survey, which tested 15-year-olds' competencies in mathematics, reading and science and, in some countries, problem solving and financial literacy. It examines the design and implementation of the project at a level of detail that allows researchers to…

  16. Materials Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-08-01

    Roadmap identifying the efforts of the Materials Technical Team (MTT) to focus primarily on reducing the mass of structural systems such as the body and chassis in light-duty vehicles (including passenger cars and light trucks) which enables improved vehicle efficiency regardless of the vehicle size or propulsion system employed.

  17. Review of technical specifications

    International Nuclear Information System (INIS)

    Bedrich, M.; Scholz, D.

    1980-01-01

    The present paper deals with position and function of technical specifications before and during the manufacturing of reactor components, their structure and reasons for specific regulations due to safety philosophy and explains the cooperation of supplier, manufacturer, utilities and supervisory organizations. (RW)

  18. Technical memory 1999

    International Nuclear Information System (INIS)

    2000-01-01

    The technical memory 1999 of the Nuclear Regulatory Authority (NRA) of the Argentine Republic, compile the papers published in the subject on radiation protection and nuclear safety, safeguards and physical protection, and presented in congress or meetings of these specialities by personnel of the mentioned institution during 1999

  19. Complex variables

    CERN Document Server

    Flanigan, Francis J

    2010-01-01

    A caution to mathematics professors: Complex Variables does not follow conventional outlines of course material. One reviewer noting its originality wrote: ""A standard text is often preferred [to a superior text like this] because the professor knows the order of topics and the problems, and doesn't really have to pay attention to the text. He can go to class without preparation."" Not so here-Dr. Flanigan treats this most important field of contemporary mathematics in a most unusual way. While all the material for an advanced undergraduate or first-year graduate course is covered, discussion

  20. Bioethics for Technical Experts

    Science.gov (United States)

    Asano, Shigetaka

    Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

  1. Sources of technical assistance

    International Nuclear Information System (INIS)

    Laue, H.J.

    1977-01-01

    This paper shows examples of technical assistance programmes within bilateral cooperation agreements between the Federal Republic of Germany and a number of developing countries of very different characteristics and summarizes the possibilities of technical assistance granted by international organizations, such as IAEA, UNDP, etc. A basic requirement for a successful transfer of technology is a high knowledge level of the indigenous scientists and engineers. Therefore, programmes for training and education and for information exchange are presented. Based on these, the means and methods of planning, performance and quality assurance are explained by practical examples and are related to the progress achieved in the use of nuclear energy and in establishing a national industry in the developing countries. (orig.) [de

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The Joint PVSS JCOP Framework: 14 - 18.6.2004 (5 days) EXCEL 2003 - niveau 2 : 17 & 18.6.2004 (2 jours) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 au 8.7.2004 (3 jours) Technical Training Monique Duval - Tel.74924 technical.training@cern.ch

  3. Independent technical review, handbook

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.

  4. Independent technical review, handbook

    International Nuclear Information System (INIS)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project

  5. El Salvador - Formal Technical Education

    Data.gov (United States)

    Millennium Challenge Corporation — With a budget of nearly $20 million, the Formal Technical Education Sub-Activity was designed to strengthen technical and vocational educational institutions in the...

  6. Technical Leadership Development Program

    Science.gov (United States)

    2010-12-13

    the traditional tenets of leadership and management , systems thinking, understanding SOS issues, and thinking and acting holistically. Our research...international element 2.0 Enterprise Leadership and Management UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 002. TO002, RT 004 Report No...mechanisms for leadership of the overall technical effort, for systems engineering, for requirements, management , and for systems integration. o Develop

  7. Technical approach document

    International Nuclear Information System (INIS)

    1989-12-01

    The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

  8. Technical training - Places available

    CERN Multimedia

    2012-01-01

    If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924) HR Department Electronic Design Next Session Duration Language Availability Comprehensive VHDL for FPGA Design 08-Oct-12 to 12-Oct-12 5 days English 4 places Electrostatique / Protection ESD 28-Sep-12 to 28-Sep-12 3 hours French 25 places Impacts de la suppression du plomb (RoHS) en électronique 26-Oct-12 to 26-Oct-12 8 hours French 14 places Introduction to VHDL 10-Oct-12 to 11-Oct-12 2 days English 9 places LabVIEW Real Time and FPGA 13-Nov-12 to 16-Nov-12 5 days French 5 places LabVIEW for Experts 24-Sep-12 to 28-Sep-12 5 days English 6 places LabVIEW for beginners 15-Oct-12 to 17-...

  9. Manageability of Technical Innovation through Technical Property Rights

    Directory of Open Access Journals (Sweden)

    Michael Horeth

    2016-06-01

    Full Text Available The term innovation is used in many respects and has been evolving over the last decades. This paper mainly focusses on managing technical innovation and differentiates this kind of innovation from others. For managing technical innovation, this work applies technical property rights, patents and utility models. The opportunity to protect the companies’ technical knowledge legally is, apart from strategic measurements like trade secrecy, a very valuable tool to manage and commercialize innovation considering the shift from closed to rather open innovation. This paper discusses the applicability of legal protection measurements for the management of technical innovation containing a critical appraisal.

  10. Assessing Students' Technical Skill Attainment

    Science.gov (United States)

    Jorgensen, Haley

    2010-01-01

    The Wisconsin Technical College System (WTCS) is working to comply with the Carl D. Perkins Career and Technical Education Improvement Act of 2006 (Perkins) to ensure that its graduates have mastered the technical skills needed by business and industry. The legislation requires that each state identify and approve program assessment strategies…

  11. Technical efficiency of selected hospitals in Eastern Ethiopia.

    Science.gov (United States)

    Ali, Murad; Debela, Megersa; Bamud, Tewfik

    2017-12-01

    This study examines the relative technical efficiency of 12 hospitals in Eastern Ethiopia. Using six-year-round panel data for the period between 2007/08 and 2012/13, this study examines the technical efficiency, total factor productivity, and determinants of the technical inefficiency of hospitals. Data envelopment analysis (DEA) and DEA- based Malmquist productivity index used to estimate relative technical efficiency, scale efficiency, and total factor productivity index of hospitals. Tobit model used to examine the determinants of the technical inefficiency of hospitals. The DEA Variable Returns to Scale (VRS) estimate indicated that 6 (50%), 5 (42%), 3 (25%), 3 (25%), 4 (33%), and 3 (25%) of the hospitals were technically inefficient while 9 (75%), 9 (75%), 7 (58%), 7 (58%), 7 (58%) and 8 (67%) of hospitals were scale inefficient between 2007/08 and 2012/13, respectively. On average, Malmquist Total Factor Productivity (MTFP) of the hospitals decreased by 3.6% over the panel period. The Tobit model shows that teaching hospital is less efficiency than other hospitals. The Tobit regression model further shows that medical doctor to total staff ratio, the proportion of outpatient visit to inpatient days, and the proportion of inpatients treated per medical doctor were negatively related with technical inefficiency of hospitals. Hence, policy interventions that help utilize excess capacity of hospitals, increase doctor to other staff ratio, and standardize number of inpatients treated per doctor would contribute to the improvement of the technical efficiency of hospitals.

  12. Methodology for technical risk assessment

    International Nuclear Information System (INIS)

    Waganer, L.M.; Zuckerman, D.S.

    1983-01-01

    A methodology has been developed for and applied to the assessment of the technical risks associated with an evolving technology. This methodology, originally developed for fusion by K. W. Billman and F. R. Scott at EPRI, has been applied to assess the technical risk of a fuel system for a fusion reactor. Technical risk is defined as the risk that a particular technology or component which is currently under development will not achieve a set of required technical specifications (i.e. probability of failure). The individual steps in the technical risk assessment are summarized. The first step in this methodology is to clearly and completely quantify the technical requirements for the particular system being examined. The next step is to identify and define subsystems and various options which appear capable of achieving the required technical performance. The subsystem options are then characterized regarding subsystem functions, interface requirements with the subsystems and systems, important components, developmental obstacles and technical limitations. Key technical subsystem performance parameters are identified which directly or indirectly relate to the system technical specifications. Past, existing and future technical performance data from subsystem experts are obtained by using a Bayesian Interrogation technique. The input data is solicited in the form of probability functions. Thus the output performance of the system is expressed as probability functions

  13. Technics and ethics

    International Nuclear Information System (INIS)

    Budnick, D.; Gemmel, F.

    1981-01-01

    Questions about the sense of life and the responsibility of technology are ethical questions. Young people in our neighbourhood who, compared to some time ago, see, hear and read much more of the world, deal with them increasingly. However, the permanent stream of information does not at all facilitate orientation but prevents many people from gaining some clearness about their own point of view. In asking the questions: where are we today. How can we get on. How can we start. The relation between ethics and technics is discussed under various aspects. (orig./HSCH) [de

  14. INOPS Technical Report

    DEFF Research Database (Denmark)

    Lindholst, Andrej Christian

    This research report contains background analyses and findings from the INOPS research project. The purpose of the INOPS project was, from an international perspective, to describe, analyse and recommend different forms of contracting out and public–private co-operations within the technical area...... in Denmark, Sweden, Norway and England. The research report addresses three key research questions in a comparative perspective: 1. Why are park and road maintenance services contracted out? 2. How are park and road maintenance services contracted out? 3. What are the outcomes from contracting out park...

  15. Argentina technical report

    International Nuclear Information System (INIS)

    2002-01-01

    At present, the Production Cyclotron Facility, installed at the Ezeiza Atomic Centre, is used for Tl-201 production; F-18 and I-123 production will be incorporated during this year. Concerning I-123 production, a system for irradiation of gaseous target has been developed in the frame of the IAEA Technical Assistance Project (ARG4085). The iodine production system delivers an ultra pure radioisotope via nuclear reactions: 124 Xe (p,2n) 123 Cs → 123 Xe → 123 I and 124 Xe (p,pn) 123 Xe → 123 I. This report describes the target and irradiation chamber design, the radiochemical purification process

  16. HPCG Benchmark Technical Specification

    Energy Technology Data Exchange (ETDEWEB)

    Heroux, Michael Allen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dongarra, Jack [Univ. of Tennessee, Knoxville, TN (United States); Luszczek, Piotr [Univ. of Tennessee, Knoxville, TN (United States)

    2013-10-01

    The High Performance Conjugate Gradient (HPCG) benchmark [cite SNL, UTK reports] is a tool for ranking computer systems based on a simple additive Schwarz, symmetric Gauss-Seidel preconditioned conjugate gradient solver. HPCG is similar to the High Performance Linpack (HPL), or Top 500, benchmark [1] in its purpose, but HPCG is intended to better represent how today’s applications perform. In this paper we describe the technical details of HPCG: how it is designed and implemented, what code transformations are permitted and how to interpret and report results.

  17. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Sobecky, Patricia A; Taillefert, Martial

    2013-03-29

    This final technical report describes results and findings from a research project to examine the role of microbial phosphohydrolase enzymes in naturally occurring subsurface microorganisms for the purpose of promoting the immobilization of the radionuclide uranium through the production of insoluble uranium phosphate minerals. The research project investigated the microbial mechanisms and the physical and chemical processes promoting uranium biomineralization and sequestration in oxygenated subsurface soils. Uranium biomineralization under aerobic conditions can provide a secondary biobarrier strategy to immobilize radionuclides should the metal precipitates formed by microbial dissimilatory mechanisms remobilize due to a change in redox state.

  18. RADTRAN 6 technical manual.

    Energy Technology Data Exchange (ETDEWEB)

    Weiner, Ruth F.; Neuhauser, Karen Sieglinde; Heames, Terence John; O' Donnell, Brandon M.; Dennis, Matthew L.

    2014-01-01

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  19. RADTRAN 6 Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Weiner, Ruth F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neuhauser, Karen Sieglinde [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Heames, Terence John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); O' Donnell, Brandon M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dennis, Matthew L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-01-01

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  20. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 28.6 - 1.7.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo... Work with long documents : 6.7.2005 (afternoon) ACCES...

  1. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Joint PVSS JCOP Framework: 8 - 12.8.2005 (5 days) FrontPage 2003 - niveau 1 : 1 - 2.9.2005 (2 jours) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.9.2005 (1 jour) LabVIEW Basics 1 : 5 - 7.9.2005 (3 days, dates to be confirmed) Introduction à Windows XP au CERN : 12.9.2005 (1 demi-journée) FrontPage 2003 - niveau 2 : 15 - 16.9.2005 (2 jours) AutoCAD 2005 - niveau 1 : 22, 23, 28, 29.9.2005 (4 jours) MAGNE-05 - Magnétisme pour l'électrotechnique : 27 - 29.9.2005 (3 jours) LabVIEW Application Development (Intermediate I): 5 - 7.12.2005 (3 days) LabVIEW Advanced Programming (Intermediate 2): 8 - 9.12.2005 (2 days) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

  2. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Hands-on Introduction to Python Programming: 28 - 30.6.2005 (3 days) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP: 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003: 30.6.2005 (IT Technical Training Tutorial, free of charge) Utilisation des fichiers PDF avec ACROBAT 7.0 : 5.7.2005 (1 jour) FrontPage 2003 - niveau 1 : 6-7.7.2005 (2 jours) LabVIEW base 1 : 4 - 6.7.2005 (3 jours) LabVIEW Basics 2: 7 - 8.7.2005 (2 days) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoCorrect, Find/Replace) : 4.7.2005 (afternoon) WORD 2003 (Short Course II) - HowTo... Mail merge: 5.7.2005 (afternoon) WORD 2003 (Short Course III) - HowTo (4 mornings) EXCEL 2003 (Short Course I) - HowTo... Work ...

  3. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW...

  4. Technical Training: Places available

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 1.4.2004 (morning) FrontPage XP - niveau 1 : 5 & 6.4.2004 (2 jours) AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 day...

  5. Technical Training: Places available

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: LabVIEW base 1 : 25 - 27.2.2004(3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) LabVIEW hands-on (E) : 16.3.2004 (afternoon) LabVIEW Basics 1 : 22 - 24.3.2004 ...

  6. TECHNICAL TRAINING: Places available**

    CERN Multimedia

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval Tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The EDMS-MTF in practice (free of charge) : 28 -  30.10.03 (6 half-day sessions) AutoCAD 2002 – Level 1 : 3, 4, 12, 13.11.03 (4 days) LabVIEW TestStand ver. 3 : 4 & 5.11.03 (2 days) Introduction to PSpice : 4.11.03 p.m. (half-day) Hands-on Introduction to Python Programming : 12 – 14.11.03 (3 days) ACCESS ...

  7. Technical Training: Places available

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Planning with MS-Project : 6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 10 - 12.5.2004 (3...

  8. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Project Planning with MS-Project :6 & 13.5.2004 (2 days) Word 2003 - niveau 1 : 10 & 11.5.2004 (2 jours) Oracle 9i : SQL : 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1: 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1 : 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL : 2 - 4.6.2...

  9. Technical Training: Places available

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study for Microsoft applications :12.2.2004 (morning) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) CLEAN-2002 ...

  10. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 19, 20.4 et 3, 4.5.2004 (4 jours) Oracle 8i/9i - Develop Web-based Applications with PL/SQL : 19 & 20.4.2004 (2 days) Introduction to ANSYS : 20 - 23.4.2004 (4 days) LabVIEW Hands-on : 20.4.2004 (half-day, p.m.) FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 -...

  11. Technical Training: Places available**

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: The JAVA Programming Language Level 1 : 9 & 10.1.2004 (2 days) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Particle Physicists : 8 - 12.3.2004 ( 6 X 4-hour sessions) LabVIEW hands-on (E) 16.3...

  12. Technical Training: Places available

    CERN Document Server

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Instructor-led WBTechT study or follow-up for Microsoft applications : 19.2.2004 (morning) LabVIEW TestStand I (E) : 23 & 24.2.2004 (2 days) LabVIEW base 1 : 25 - 27.2.2004 (3 jours) Instructor-led WBTechT study or follow-up for Microsoft applications : 26.2.2004 (morning) CLEAN-2002 : Working in a Cleanroom : 10.3.2004 (afternoon - free of charge) C++ for Pa...

  13. Technical Training: Places available

    CERN Document Server

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) VisualEliteHDL : 25 & 26.5.2004 (2 days) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9...

  14. Technical Training: Places Available

    CERN Document Server

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. Technical Training Monique Duval - Tel.74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Oracle 9i: SQL: 17 - 19.5.2004 (3 days) Word 2003 - niveau 2 : 24 & 25.5.2004 (2 jours) EXCEL 2003 - niveau 1 : 27 & 28.5.2004 (2 jours) STEP7 Programming Level 1: 1 - 4.6.2004 (4 days) Oracle 9i : Programming with PL/SQL: 2 - 4.6.2004 (3 days) CST Microwave Studio: 3 & 4.6.2004 (2 days) Oracle 9i : New f...

  15. Technical Training: Places available

    CERN Multimedia

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: FrontPage XP - niveau 2 : 26 & 27.4.2004 (2 jours) The Joint PVSS JCOP Framework : 26 - 30.4.2004 (5 days) Computational Electromagnetics with the ELEKTRA Module of OPERA-3D : 27 & 28.4.2004 (2 days) Hands-on Introduction to Python Programming : 3 - 5.5.2004 (3 days) LabVIEW Base 2 : 6 & 7.5.2004 (2 jours) Project Pla...

  16. TECHNICAL TRAINING: Places available**

    CERN Document Server

    2003-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch ** The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: Hands-on Introduction to Python Programming : 12 - 14.11.03(3 days) ACCESS 2000 - niveau 1 : 13 & 14.11.03 (2 jours) C++ for Particle Physicists : 17 - 21.11.03 (6 X 3-hour lectures) Programmation automate Schneider TSX Premium - niveau 2 : 18 - 21.11.03 (4 jours) Project Planning with MS-Project  (free of charg...

  17. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: C++ for Particle Physicists : 8 - 12.3.2004 (6 X 4-hour sessions) Introduction to the CERN EDMS : 9.3.2004 (1 day, free of charge) The EDMS MTF in Practice : 10.3.2004 (morning, free of charge) CLEAN-2002: Working in a Cleanroom : 10.3.2004 (afternoon, free of charge) The CERN EDMS for Engineers : 11.3.2004 (1 day, free of charge) LabVIEW hands-on (E):...

  18. Technical training: places available

    CERN Multimedia

    HR Department

    2007-01-01

    CERN Technical Training: Open Courses (April - June 2007) The following course sessions are currently scheduled in the framework of the CERN Technical Training Programme 2007:   AutoCAD 2006 - niveau 1 (course in French): 25.4.- 26.4.2007 & 2.5. - 3.5.2007 (4 days in 2 modules, 5 places available) AutoCAD 2006 - niveau 1 (course in French): 27.6.- 28.6.2007 & 3.7. - 4.7.2007 (4 days in 2 modules, 5 places available) AutoCAD Mechanical 2006 (course in French) 21.6.-22.6.2007 (2 days, 8 places available) * NEW COURSE* Automate de securite S7 (course in French) 14.5.-16.5.2007 (3 days, 4 places available) * NEW COURSE* Automate de securite S7 (course in French): 9.5.-11.5.2007 (3 days, 4 places available) JCOP - Joint PVSS-JCOP Frameswork (course in English): 21.5.-25.5.2007 (5 days, 12 places available) JCOP - Finite State Machines in the JCOP Frameswork (course in English): 12.6.-14.6.2007 (3 days, 12 places available) LabVIEW Basics 1 (in English): 2.-4.5.2007 (3 days, 7 places ...

  19. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Wednesday 6 March TECHNICAL TRAINING SEMINAR from 9:30 to 16:45 - IT Amphitheatre - bldg. 31.3.004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars...

  20. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Mark H. Dawson

    2005-06-30

    This variable length wind turbine blade project met the project objectives by successfully completing the task schedule. A set of variable length blades (8 to 12 meters in length) is now flying, in a configuration that is representative of a commercial blade designed to replace a standard 9 meter blade. Static testing and operations show that the blades are durable and stiff enough to prevent tower strikes. Power curve testing shows significant gains in low wind speed power production. An improved controller and drive mechanism have now been working for six months. Moving forward, we continue to monitor power curve, controller performance, and durability data. The project has made good progress towards understanding the costs and challenges associated with commercial production of variable length blades. Items that will require further study are: tip airfoil; blade pitching, tip and root interface design; jigs for more efficient construction, and optimization of subsystems

  1. Technical standards in the law of technical safety

    International Nuclear Information System (INIS)

    Marburger, P.

    1985-01-01

    Technical standards are of great importance for the closer definition of inexact terms of law, for instance ''generally accepted technical rules'', ''state of the art'', ''state of science and technology'' or similar normative terms, in the law of technical safety. The paper discusses with whom the authority for regulating this sector of law rests, deals with the different ways of how technical standards are used by the law (''anticipated expert opinion'', reference to such standards in law and administration) and points out demands on the procedure of standardization. (orig.) [de

  2. Technical Support Essentials Advice to Succeed in Technical Support

    CERN Document Server

    Sanchez, Andrew

    2010-01-01

    Technical Support Essentials is a book about the many facets of technical support. It attempts to provide a wide array of topics to serve as points of improvement, discussion, or simply topics that you might want to learn. The topics range from good work habits to the way technical supportgroups establish their own style of work. This book applies theories, models, and concepts synthesized from existing research in other fields-such as management, economics, leadership, and psychology-and connects them to technical support. The goal is to build on the work of others and allow their success to

  3. Continuous-variable supraquantum nonlocality

    Science.gov (United States)

    Ketterer, Andreas; Laversanne-Finot, Adrien; Aolita, Leandro

    2018-01-01

    Supraquantum nonlocality refers to correlations that are more nonlocal than allowed by quantum theory but still physically conceivable in postquantum theories, in the sense of respecting the basic no-faster-than-light communication principle. While supraquantum correlations are relatively well understood for finite-dimensional systems, little is known in the infinite-dimensional case. Here, we study supraquantum nonlocality for bipartite systems with two measurement settings and infinitely many outcomes per subsystem. We develop a formalism for generic no-signaling black-box measurement devices with continuous outputs in terms of probability measures, instead of probability distributions, which involves a few technical subtleties. We show the existence of a class of supraquantum Gaussian correlations, which violate the Tsirelson bound of an adequate continuous-variable Bell inequality. We then introduce the continuous-variable version of the celebrated Popescu-Rohrlich (PR) boxes, as a limiting case of the above-mentioned Gaussian ones. Finally, we characterize the geometry of the set of continuous-variable no-signaling correlations. Namely, we show that that the convex hull of the continuous-variable PR boxes is dense in the no-signaling set. We also show that these boxes are extreme in the set of no-signaling behaviors and provide evidence suggesting that they are indeed the only extreme points of the no-signaling set. Our results lay the grounds for studying generalized-probability theories in continuous-variable systems.

  4. Technical knowledge creation

    DEFF Research Database (Denmark)

    Søberg, Peder Veng

    2017-01-01

    Purpose - The purpose of the paper is to amend shortcomings of existing theory concerning organizational learning and knowledge management. Design/methodology/approach – The paper reviews and refines existing theory. Findings - Findings from cognitive neuroscience suggest that technical knowledge...... domains essential for product development are largely nonlinguistic. Operations management/strategy tools enable the use of tacit knowledge in its tacit form and discourage premature standardization. Similarly, language use introduces standardization, which if introduced prematurely, causes incrementalism...... in line with findings from product development research. However, frameworks on organizational learning and knowledge management focus on language development and neglect use of tacit knowledge and the benefits involved with allowing elements of new product ideas to mature in a tacit form. Originality...

  5. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Wednesday 19 November From 9:30 to 17:30 - IT Amphitheatre bldg.31 3-004 2003 Data Transmission Design Seminar - TEXAS INSTRUMENTS The one-day 2003 Data Transmission Design Seminar is part of a series of technical seminars produced by Texas Instruments. This series of seminars will introduce system solutions based on different standards according to their respective requirements. It will include topics containing a blend of basic principles and hands-on application examples, along with layout-guidelines. • Basics and Practical Examples of Data-Transmission • Low Voltage Differential Signaling (LVDS) • Connectivity and PC-based Links • Industrial Interfaces • Parallel Bus Systems and Clock-Distribution-Circuits (CDC) This Seminar will be of interest to hardware designers and system engineers dealing with the realization of system- or board-level interfaces based on various transmission standards. Language: English Free seminar, no registration Organiser: John ...

  6. Technical Math For Dummies

    CERN Document Server

    Schoenborn, Barry

    2010-01-01

    Technical Math For Dummies is your one-stop, hands-on guide to acing the math courses you’ll encounter as you work toward getting your degree, certifacation, or�license in the skilled trades. You’ll get easy-to-follow, plain-English guidance on mathematical formulas and methods that professionals use every day in the automotive, health, construction, licensed trades, maintenance, and other trades. You’ll learn how to apply concepts of algebra, geometry, and trigonometry and their formulas related to occupational areas of study. Plus, you’ll find out how to perform basic arithmetic

  7. Technical applications of aerogels

    International Nuclear Information System (INIS)

    Hrubesh, L.W.

    1997-01-01

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels

  8. Technical Training: ELEC-2005

    CERN Multimedia

    Davide Vitè

    2005-01-01

    ELEC-2005 - Electronics in High Energy Physics: Autumn Term (November-December 2005) ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the ELEC-2002 course series. This new, comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms. The Winter (Introduction to electronics in HEP), Spring (Integrated circuits and VLSI technology for physics), and Summer (System electronics for physics: Issues) Terms already took place. The Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) is now open for online registration, and will start on November 8th with the...

  9. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

    2016-08-17

    ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

  10. Technical Report - FINAL

    Energy Technology Data Exchange (ETDEWEB)

    Barbara Luke, Director, UNLV Engineering Geophysics Laboratory

    2007-04-25

    Improve understanding of the earthquake hazard in the Las Vegas Valley and to assess the state of preparedness of the area's population and structures for the next big earthquake. 1. Enhance the seismic monitoring network in the Las Vegas Valley 2. Improve understanding of deep basin structure through active-source seismic refraction and reflection testing 3. Improve understanding of dynamic response of shallow sediments through seismic testing and correlations with lithology 4. Develop credible earthquake scenarios by laboratory and field studies, literature review and analyses 5. Refine ground motion expectations around the Las Vegas Valley through simulations 6. Assess current building standards in light of improved understanding of hazards 7. Perform risk assessment for structures and infrastructures, with emphasis on lifelines and critical structures 8. Encourage and facilitate broad and open technical interchange regarding earthquake safety in southern Nevada and efforts to inform citizens of earthquake hazards and mitigation opportunities

  11. ITER technical basis

    International Nuclear Information System (INIS)

    2002-01-01

    Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties

  12. Technical applications of aerogels

    Energy Technology Data Exchange (ETDEWEB)

    Hrubesh, L.W.

    1997-08-18

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

  13. LLNL 1981: technical horizons

    International Nuclear Information System (INIS)

    1981-07-01

    Research programs at LLNL for 1981 are described in broad terms. In his annual State of the Laboratory address, Director Roger Batzel projected a $481 million operating budget for fiscal year 1982, up nearly 13% from last year. In projects for the Department of Energy and the Department of Defense, the Laboratory applies its technical facilities and capabilities to nuclear weapons design and development and other areas of defense research that include inertial confinement fusion, nonnuclear ordnances, and particle-beam technology. LLNL is also applying its unique experience and capabilities to a variety of projects that will help the nation meet its energy needs in an environmentally acceptable manner. A sampling of recent achievements by LLNL support organizations indicates their diversity

  14. Mechanical Engineering Department Technical Review

    Energy Technology Data Exchange (ETDEWEB)

    Carr, R.B.; Denney, R.M. (eds.)

    1981-07-01

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication.

  15. Mechanical engineering department technical review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

  16. Mechanical Engineering Department. Technical review

    Energy Technology Data Exchange (ETDEWEB)

    Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

  17. TECHNICAL CULTURE AND HUMAN AXJOSPHERE

    OpenAIRE

    ­Krystyna Chałas

    2014-01-01

    Technical culture is the value of each historical period. It is the subject of the ongoing development. While it is a value which is associated with different categories of values, mainly material, cognitive, social. Between culture and these three categories of values ​ there is a cognitive effect. Technical culture determines the quality of human axjosphere. The aim of this study is to show the relationships and dependencies between technical culture and the structures in which a person liv...

  18. Mechanical engineering department technical review

    Energy Technology Data Exchange (ETDEWEB)

    Carr, R.B. Denney, R.M. (eds.)

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work.

  19. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    Denney, R.M.

    1982-01-01

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

  20. Mechanical Engineering Department. Technical review

    International Nuclear Information System (INIS)

    Simecka, W.B.; Condouris, R.A.; Talaber, C.

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

  1. Mechanical Engineering Department Technical Review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

  2. Mechanical Engineering Department technical abstracts

    Energy Technology Data Exchange (ETDEWEB)

    Denney, R.M. (ed.)

    1982-07-01

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts.

  3. The story of technical cooperation

    International Nuclear Information System (INIS)

    Park, Yang Taek

    1989-09-01

    This book gives descriptions of technical cooperation, which is about why does technology transfer?, process of technology transfer with model, decisive cause and cooperation of technology transfer, cost and effect of technology transfer, historical experience of technology transfer, cases of technology transfer by field such as rubber tire, medicine and computer industry and automobile industry, technology transfer process and present condition of technical cooperation, and strategy for rising of technical cooperation : selection of technology for object of cooperation and development of human resources.

  4. The logic of Technical Standardisation

    DEFF Research Database (Denmark)

    Nedergaard, Peter

    In this paper technical standardisation is understood and explained in a model where economic analysis is coupled with an analysis of the political system as proposed in rational choice theory. The aim is to answer both the question why various countries (e.g. the United States versus European...... countries) let either the market or public intervention determine the mode of technical standardisation and the possible implications of these two ways of organizing technical standardisation from an economic and a political point of view. Based upon the analysis of the paper a couple of general policy...... recommendations are made concerning the mode of technical standardisation....

  5. Technical-tactical analysis of youth olympic taekwondo combat.

    Science.gov (United States)

    Tornello, Francesco; Capranica, Laura; Minganti, Carlo; Chiodo, Salvatore; Condello, Giancarlo; Tessitore, Antonio

    2014-04-01

    The purpose of this study was to define the technical and tactical profiles of official youth taekwondo competitions played under the most recent rules of the International Taekwondo Federation. Tactical actions (i.e., attack, defense, and block), technical executions (from 1- to 4-point scores), kicking legs (i.e., front/rear and right/left), and overall technical effectiveness were investigated in relation to match outcome of semifinal and final competitions (n = 50) of youth (aged 13-14 years) black belt athletes during the Italian Taekwondo Cadet Championship. Differences (p technical exchanges showed differences (p technical executions. Winners resulted more efficient (p technical and tactical variables. In general, these findings showed that Cadets tend to adopt an offensive strategy. In considering that the adoption of the new electronic system requires athletes to execute correct technical actions to have a score assigned, coaches should emphasize the effectiveness of scoring techniques and help athletes to effectively improve their defense and counterattack capabilities.

  6. Continuous-Variable Entanglement Swapping

    Directory of Open Access Journals (Sweden)

    Kevin Marshall

    2015-05-01

    Full Text Available We present a very brief overview of entanglement swapping as it relates to continuous-variable quantum information. The technical background required is discussed and the natural link to quantum teleportation is established before discussing the nature of Gaussian entanglement swapping. The limitations of Gaussian swapping are introduced, along with the general applications of swapping in the context of to quantum communication and entanglement distribution. In light of this, we briefly summarize a collection of entanglement swapping schemes which incorporate a non-Gaussian ingredient and the benefits of such schemes are noted. Finally, we motivate the need to further study and develop such schemes by highlighting requirements of a continuous-variable repeater.

  7. Technical note The formulation of synthetic domestic wastewater ...

    African Journals Online (AJOL)

    Technical note The formulation of synthetic domestic wastewater sludge medium to study anaerobic biological treatment of acid mine drainage in the laboratory. ... Journal Home > Vol 42, No 2 (2016) > ... Domestic wastewater sludge is however highly variable in its composition, making laboratory experimentation difficult.

  8. Technical descriptions of ten irrigation technologies for conserving energy

    Energy Technology Data Exchange (ETDEWEB)

    Harrer, B.J.; Wilfert, G.L.

    1983-05-01

    Technical description of ten technologies which were researched to save energy in irrigated agriculture are presented. These technologies are: well design and development ground water supply system optimization, column and pump redesign, variable-speed pumping, pipe network optimization, reduced-pressure center-pivot systems, low-energy precision application, automated gated-pipe system, computerized irrigation scheduling, and instrumented irrigation scheduling. (MHR)

  9. 90 measurement of technical efficiency and its determinants in crop ...

    African Journals Online (AJOL)

    OLUWOLE AKINNAGBE

    Department of Agricultural Economics and Extension Nasarawa State University, Keffi, Lafia ... The significant socio economic variables that accounted for the ..... Betesse G. E. and Colli, T. (1995). A model of. Technical Inefficiency Effects in a stochastic Friontier Production function for Panel Data. Empirical Economics.

  10. Analysis of Technical Efficiency of Haricot Bean Production in Misrak ...

    African Journals Online (AJOL)

    In addition, results of inefficiency analysis indicates that draught animals ownership, age, extension contact, soil fertility status, and availability of market and price condition of the output were negatively and significantly affect technical inefficiency of haricot bean production implying that improvement in these variables ...

  11. Predictors of employer satisfaction: technical and non-technical skills.

    Science.gov (United States)

    Danielson, Jared A; Wu, Tsui-Feng; Fales-Williams, Amanda J; Kirk, Ryan A; Preast, Vanessa A

    2012-01-01

    Employers of 2007-2009 graduates from Iowa State University College of Veterinary Medicine were asked to respond to a survey regarding their overall satisfaction with their new employees as well as their new employees' preparation in several technical and non-technical skill areas. Seventy-five responses contained complete data and were used in the analysis. Four technical skill areas (data collection, data interpretation, planning, and taking action) and five non-technical skill areas (interpersonal skills, ability to deal with legal issues, business skills, making referrals, and problem solving) were identified. All of the skill area subscales listed above had appropriate reliability (Cronbach's alpha>0.70) and were positively and significantly correlated with overall employer satisfaction. Results of two simultaneous regression analyses indicated that of the four technical skill areas, taking action is the most salient predictor of employer satisfaction. Of the five non-technical skill areas, interpersonal skills, business skills, making referrals, and problem solving were the most important skills in predicting employer satisfaction. Hierarchical regression analysis revealed that all technical skills explained 25% of the variation in employer satisfaction; non-technical skills explained an additional 42% of the variation in employer satisfaction.

  12. The logic of Technical Standardisation

    DEFF Research Database (Denmark)

    Nedergaard, Peter

    countries) let either the market or public intervention determine the mode of technical standardisation and the possible implications of these two ways of organizing technical standardisation from an economic and a political point of view. Based upon the analysis of the paper a couple of general policy...

  13. Technical Education and Economic Growth

    Indian Academy of Sciences (India)

    Technical Education and Economic Growth. Technical Education and Economic Growth. Review of the Present Status. Expanding no.s and impairment of quality; Faculty shortage; Grim situation ... Absence of International flavour. Consequences of Low Research. Some Success Stories. New Models of Institutional Structure ...

  14. The Digital technical documentation handbook

    CERN Document Server

    Schultz, Susan I; Kavanagh, Frank X; Morse, Marjorie J

    1993-01-01

    The Digital Technical Documentation Handbook describes the process of developing and producing technical user information at Digital Equipment Corporation. * Discusses techniques for making user information _more effective * Covers the draft and reviewprocess, the production and distribution of printed and electronic media, archiving, indexing, testing for usability, and many other topics * Provides quality assurance checklists, contains a glossary and a bibliography of resources for technicalcommunicators

  15. Aligning Career and Technical Education

    Science.gov (United States)

    Workman, Ed; Stubbs, Joyce

    2011-01-01

    The issues and concerns facing Kentucky Career and Technical Teacher Education (KY CTTE), university teacher educators and state department Career and Technical Education (CTE) leaders in providing and preparing the best CTE teachers possible are not unique to Kentucky. In an effort to better understand these issues and concerns a team of state…

  16. Technical Education and Economic Growth

    Indian Academy of Sciences (India)

    First page Back Continue Last page Graphics. Technical Education and Economic Growth. Technical Education and Economic Growth. Review of the Present Status. Expanding no.s and impairment of quality; Faculty shortage; Grim situation at Masters and PhD levels; Regional imbalance; Absence of International flavour ...

  17. COMPASS Accelerator Design Technical Overview

    Energy Technology Data Exchange (ETDEWEB)

    Nanni, Emilio; Dolgashev, Valery; Tantawi, Sami; Neilson, Jeff; /SLAC

    2016-03-14

    This report is a survey of technical options for generating a MeV-class accelerator for space based science applications. The survey was performed focusing on the primary technical requirements of the accelerator in the context of a satellite environment with its unique challenges of limited electrical power (PE), thermal isolation, dimensions, payload requirement and electrical isolation.

  18. Technical planning activity: Final report

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

  19. Technical planning activity: Final report

    International Nuclear Information System (INIS)

    1987-01-01

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

  20. Variable Valve Actuation

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey Gutterman; A. J. Lasley

    2008-08-31

    Many approaches exist to enable advanced mode, low temperature combustion systems for diesel engines - such as premixed charge compression ignition (PCCI), Homogeneous Charge Compression Ignition (HCCI) or other HCCI-like combustion modes. The fuel properties and the quantity, distribution and temperature profile of air, fuel and residual fraction in the cylinder can have a marked effect on the heat release rate and combustion phasing. Figure 1 shows that a systems approach is required for HCCI-like combustion. While the exact requirements remain unclear (and will vary depending on fuel, engine size and application), some form of substantially variable valve actuation is a likely element in such a system. Variable valve actuation, for both intake and exhaust valve events, is a potent tool for controlling the parameters that are critical to HCCI-like combustion and expanding its operational range. Additionally, VVA can be used to optimize the combustion process as well as exhaust temperatures and impact the after treatment system requirements and its associated cost. Delphi Corporation has major manufacturing and product development and applied R&D expertise in the valve train area. Historical R&D experience includes the development of fully variable electro-hydraulic valve train on research engines as well as several generations of mechanical VVA for gasoline systems. This experience has enabled us to evaluate various implementations and determine the strengths and weaknesses of each. While a fully variable electro-hydraulic valve train system might be the 'ideal' solution technically for maximum flexibility in the timing and control of the valve events, its complexity, associated costs, and high power consumption make its implementation on low cost high volume applications unlikely. Conversely, a simple mechanical system might be a low cost solution but not deliver the flexibility required for HCCI operation. After modeling more than 200 variations of

  1. AIMES Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Katz, Daniel S [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Weissman, Jon [Univ. of Minnesota, Minneapolis, MN (United States); Turilli, Matteo [Rutgers Univ., New Brunswick, NJ (United States)

    2017-01-31

    This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.

  2. GEM Technical Design Report

    International Nuclear Information System (INIS)

    1993-01-01

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p T physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E T . The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p T physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds

  3. GEM Technical Design Report

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-31

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p{sub T} physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E{sub T}. The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p{sub T} physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds.

  4. Technical training - Places available

    CERN Multimedia

    Davide Vitè

    2006-01-01

    Places available as of 16.5.2006 (May-November course sessions) Technical Training: Places available The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: Title Hours Date Language ACROBAT 7.0 : Utilisation de fichiers PDF 8 8.05.06 F WORD 2003 - niveau 2 : ECDL 16 22-23.05.06 23-24.05.06 F Comprehensive VHDL for FPGA Design 40 29.05-2.06.06 E C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls 32 30.05-2.06.06 E ACROBAT 7.0 : Utilisation de fichiers PDF 24 7-9.06.06 E AutoCAD Mechanical 2006 16 13-14.06.06 F CERN EDMS for Local Administrators 16 13-14.06.06 E LabVIEW Base 2 32 27.06-5.07.06 F C++ Programming Part 3 - Templates and the STL (Standard Template Library) 16 27-28.06.06 E C++ Programming Part 4 - Exceptions 8 29.06.06 E FrontPage 2003 - niveau 1 16 29-...

  5. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2005-01-01

    The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: PowerPoint 2003 (F) : 25.4.2005 (1 jour) WORD 2003 - niveau 1 : 2 & 3.5.2005 (2 jours) FrontPage 2003 - niveau 1 : 9 & 10.5.2005 (2 jours) ANSYS Workbench (F) : 9 - 12.5.2005 (4 jours) ELEC-2005 - Summer Term: System electronics for physics - Issues : 10, 12, 17, 19, 24, 26 & 31.5.2005 (7 x 2h lectures) AutoCAD 2005 - niveau 1 : 11, 12, 18, 19.5.2005 (4 jours) ACCESS 2003 - Level 1: ECDL M5 : 11 & 12.5.2005 (2 days) La technique du vide : 12 & 13.5.2005 (2 jours) Finite State Machines in the JCOP Framework: 24 - 26.5.2005 (3 days) The Joint PVSS JCOP Framework: 30.5 - 3.6.2005 (5 days) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) Introduction to ANSYS: 21 - 24.6.2005 (4 days) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 tech...

  6. Bulletin Survey: Technical clarifications

    CERN Multimedia

    2002-01-01

    In the latest of our articles on the results of the Bulletin survey, we respond to some of your technical comments on the Electronic Bulletin. Many thanks to the more than 500 of you who completed the questionnaire. The full statistics will be published next week. 'It takes too long to download the pages' Yes, it's true that the Electronic Bulletin's download time isn't perfect but it will improve when the Bulletin migrates to another, faster database. 'I find it very difficult to locate all the articles' Some people experience difficulty negotiating their way through the Bulletin once they have entered a specific section. The blue column on the left contains an 'In this issue' link taking you to the other sections. What's more, the whole of the paper Bulletin is available in the electronic version. As the latter is relatively new, however, it will take a bit of time to get used to browsing through it. Many of you say that it's still too early to form an opinion. 'Pull-down menus would be good, so that yo...

  7. VLLEEM-2 technical workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In order to overcome the limits of the energy-environment models, and to benefit at the same time of their past experiences, the VLEEM project proposes a genuine approach and innovative modelling tools to assess the energy-environment systems over the very long term, which are based on the strengths of existing long term energy models, but focussed on two major objectives: to describe normative futures which fit with a set of overall constraints, like the stabilisation of the concentration of green-house gases in the atmosphere, or the stabilisation of the overall inventory of plutonium and minor actinides, etc...; to describe and formalize the association of causalities necessary to bring the system from the present situation to the targeted future, through a '' back-casting '' approach. This first technical workshop presents the state of the art of the different Work Programmes. WP1:Enhancement of the Conceptual framework. WP2: Data base on conventional demand/supply technologies. WP3: Complement and up-date technology monographs. WP4: Formalization and computing of final VLEEM submodels. WP5: Case study 2030, 2050, 2100. (A.L.B.)

  8. Technical Training: Places available

    CERN Multimedia

    Monique Duval

    2004-01-01

    If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an 'application for training' form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. The number of places available may vary. Please check our Web site to find out the current availability. Places are available in the following courses: AutoCAD 2002 - niveau 1 : 13, 14, 23, 24.09.2004 (4 jours) Introduction to the CERN EDMS : 22.6.2004 (1 day) The CERN EDMS for local administrators : 23 & 24.6.2004 (2 days) MAGNE-04 : Magnétisme pour l'électrotechnique : 6 - 8.7.2004 (3 jours) Introduction au VHDL et utilisation du simulateur NCVHDL de CADENCE : 7 & 8.9.2004 (2 jours) ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING...

  9. Technical approach document

    International Nuclear Information System (INIS)

    1988-04-01

    This document describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement Remedial Action Plans (RAPs) and final designs that comply with EPS standards. This document is a revision to the original document. Major revisions were made to the sections in riprap selection and sizing, and ground-water; only minor revisions were made to the remainder of the document. The US Nuclear Regulatory Commission (NRC) has prepared a Standard Review Plan (NRC-SRP) which describes factors to be considered by the NRC in approving the RAP. Sections 3.0, 4.0, 5.0, and 7.0 of this document are arranged under the same headings as those used in the NRC-SRP. This approach is adopted in order to facilitate joint use of the documents. Section 2.0 (not included in the NRC-SRP) discusses design considerations; Section 3.0 describes surface-water hydrology and erosion control; Section 4.0 describes geotechnical aspects of pile design; Section 5.0 discusses the Alternate Site Selection Process; Section 6.0 deals with radiological issues (in particular, the design of the radon barrier); Section 7.0 discusses protection of groundwater resources; and Section 8.0 discusses site design criteria for the RAC

  10. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Stoessel, Chris

    2013-11-13

    This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency of a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.

  11. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide VITÈ

    2002-01-01

    Wednesday 6 March   from 9:30 to 16:45 - IT Auditorium - bldg. 31 3-004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars pages here or con...

  12. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Wednesday 6 March from 9:30 to 16:45 - IT Auditorium - bldg. 31 3-004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars pages here or contact the organiser.

  13. Waste Management Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, J.S. [ed.

    1967-08-31

    This Manual has been prepared to provide a documented compendium of the technical bases and general physical features of Isochem Incorporated`s Waste Management Program. The manual is intended to be used as a means of training and as a reference handbook for use by personnel responsible for executing the Waste Management Program. The material in this manual was assembled by members of Isochem`s Chemical Processing Division, Battelle Northwest Laboratory, and Hanford Engineering Services between September 1965 and March 1967. The manual is divided into the following parts: Introduction, contains a summary of the overall Waste Management Program. It is written to provide the reader with a synoptic view and as an aid in understanding the subsequent parts; Feed Material, contains detailed discussion of the type and sources of feed material used in the Waste Management Program, including a chapter on nuclear reactions and the formation of fission products; Waste Fractionization Plant Processing, contains detailed discussions of the processes used in the Waste Fractionization Plant with supporting data and documentation of the technology employed; Waste Fractionization Plant Product and Waste Effluent Handling, contains detailed discussions of the methods of handling the product and waste material generated by the Waste Fractionization Plant; Plant and Equipment, describes the layout of the Waste Management facilities, arrangement of equipment, and individual equipment pieces; Process Control, describes the instruments and analytical methods used for process control; and Safety describes process hazards and the methods used to safeguard against them.

  14. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Thursday 4 September From 14:00 to 17:00 - Training Centre Auditorium bldg. 593, room 11 The Summit Design VisualElite 4.0 Release Jean Marie St Paul / SUMMIT DESIGN, Europe, Technical Manager Michel Delcroix / SUMMIT DESIGN, Southern Europe, Sales F-95015 CERGY PONTOISE, France Summit Design is an important EDA digital hardware design tool supplier, and the industry leader in the emerging Electronic System Level design domain. Its VisualElite program has been used at CERN for several years. This seminar will include the highlights of the program's latest release. It will be illustrated how Summit Design products can provide a high-level C/C++ and SystemC functional modelling design and verification environment, enabling engineers to analyse system concepts before the implementation stage. The seminar will show how mixed SystemC and HDL simulation can be done, along with solutions for hardware/software development. • HDL new features: Connectivity Table Editor. Xemacs full integration. New NCsi...

  15. Technical Training Seminar

    CERN Multimedia

    2003-01-01

    Thursday 4 September From 14:00 to 17:00 - Training Centre Auditorium bldg. 593, room 11 The Summit Design VisualElite 4.0 Release Jean Marie St Paul / SUMMIT DESIGN, Europe, Technical Manager Michel Delcroix / SUMMIT DESIGN, Southern Europe, Sales F-95015 CERGY PONTOISE, France Summit Design is an important EDA digital hardware design tool supplier, and the industry leader in the emerging Electronic System Level design domain. Its VisualElite program has been used at CERN for several years. This seminar will include the highlights of the program's latest release. It will be illustrated how Summit Design products can provide a high-level C/C++ and SystemC functional modelling design and verification environment, enabling engineers to analyse system concepts before the implementation stage. The seminar will show how mixed SystemC and HDL simulation can be done, along with solutions for hardware/software development. • HDL new features: Connectivity Table Editor. Xemacs full integration. New NCsim ...

  16. Training of technical staff and technical staff managers

    International Nuclear Information System (INIS)

    Moody, G.F.

    1991-01-01

    The purpose of Technical Staff and Technical Staff Managers training is to provide job skills enhancement to individuals selected to fill key technical positions within a nuclear utility. This training is unique in that unlike other training programs accredited by the National Academy for Nuclear Training, it does not lead to specific task qualification. The problems encountered when determining the student population and curriculum are a direct result of this major difference. Major problems encountered are determining who should attend the training, what amount of training is necessary and sufficient, and how to obtain the best feedback in order to effect substantive program improvements. These topics will be explored and possible solutions discussed

  17. Bibliography - Technical Reports, Special Reports, and Technical Notes, FY 1981.

    Science.gov (United States)

    1982-03-01

    AD-A113 798 NAVY PERSONNEL RESEARCH AND DEVELOPMENT CENTER SAN D--ETC F/6 5/9 BIBLIOGRAPHY - TECHNICAL REPORTS. SPECIAL REPORTS. AND TECHNICA-ETC( U ...TH4IS PAGE ( MOM , Dole gnto,.d) FOREWORD This report lists all technical reports, special reports, and technical notes that were published by this Center...TR 81-16. July 1981. J. I. Borack and K. W. Gay . (AD-A102 910) A new computerized management system, the structured accession planning (STRAP) system

  18. Extracts from technical journals

    Directory of Open Access Journals (Sweden)

    Soria Santamaría, F.

    1976-12-01

    Full Text Available Not avaiableSe estudia, a través de los espectros de absorción IR, la hidratación del cemento portland hasta 28 días, considerando como variables su contenido de yeso y la dosis de cloruro cálcico añadida en el agua de amasado. Se comprueba la idoneidad de la técnica, la cual permite observar hechos diferenciales, en función de las variables consideradas. Se puede apreciar una acción antagónica entre el efecto retardador normal del yeso en el fraguado y en la hidratación, y el efecto acelerador del cloruro cálcico, a las dosis y concentraciones en que se produce. Las acciones retardadoras, tanto del yeso como del cloruro cálcico a baja concentración (1% respecto del cemento anhidro, o menor, se atribuyen a la formación predominante de ettringita, mientras que las acciones aceleradoras se explican por la formación preferente de monosulfo-aluminato, cloroaluminato y aluminato tricálcico hidratados. Las conclusiones del trabajo confirman y amplían las previas de otros autores, relativos a aspectos cualitativos y cuantitativos de la influencia del yeso y del cloruro cálcico en las propiedades y en el comportamiento del cemento en la hidratación, así como referentes al mecanismo de ésta.

  19. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Edward DeLong

    2011-10-07

    Our overarching goals in this project were to: Develop and improve high-throughput sequencing methods and analytical approaches for quantitative analyses of microbial gene expression at the Hawaii Ocean Time Series Station and the Bermuda Atlantic Time Series Station; Conduct field analyses following gene expression patterns in picoplankton microbial communities in general, and Prochlorococcus flow sorted from that community, as they respond to different environmental variables (light, macronutrients, dissolved organic carbon), that are predicted to influence activity, productivity, and carbon cycling; Use the expression analyses of flow sorted Prochlorococcus to identify horizontally transferred genes and gene products, in particular those that are located in genomic islands and likely to confer habitat-specific fitness advantages; Use the microbial community gene expression data that we generate to gain insights, and test hypotheses, about the variability, genomic context, activity and function of as yet uncharacterized gene products, that appear highly expressed in the environment. We achieved the above goals, and even more over the course of the project. This includes a number of novel methodological developments, as well as the standardization of microbial community gene expression analyses in both field surveys, and experimental modalities. The availability of these methods, tools and approaches is changing current practice in microbial community analyses.

  20. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Aristos Aristidou Natureworks); Robert Kean (NatureWorks); Tom Schechinger (IronHorse Farms, Mat); Stuart Birrell (Iowa State); Jill Euken (Wallace Foundation & Iowa State)

    2007-10-01

    The two main objectives of this project were: 1) to develop and test technologies to harvest, transport, store, and separate corn stover to supply a clean raw material to the bioproducts industry, and 2) engineer fermentation systems to meet performance targets for lactic acid and ethanol manufacturers. Significant progress was made in testing methods to harvest corn stover in a “single pass” harvest mode (collect corn grain and stover at the same time). This is technically feasible on small scale, but additional equipment refinements will be needed to facilitate cost effective harvest on a larger scale. Transportation models were developed, which indicate that at a corn stover yield of 2.8 tons/acre and purchase price of $35/ton stover, it would be unprofitable to transport stover more than about 25 miles; thus suggesting the development of many regional collection centers. Therefore, collection centers should be located within about 30 miles of the farm, to keep transportation costs to an acceptable level. These collection centers could then potentially do some preprocessing (to fractionate or increase bulk density) and/or ship the biomass by rail or barge to the final customers. Wet storage of stover via ensilage was tested, but no clear economic advantages were evident. Wet storage eliminates fire risk, but increases the complexity of component separation and may result in a small loss of carbohydrate content (fermentation potential). A study of possible supplier-producer relationships, concluded that a “quasi-vertical” integration model would be best suited for new bioproducts industries based on stover. In this model, the relationship would involve a multiyear supply contract (processor with purchase guarantees, producer group with supply guarantees). Price will likely be fixed or calculated based on some formula (possibly a cost plus). Initial quality requirements will be specified (but subject to refinement).Producers would invest in harvest

  1. Technical and economic guidelines

    International Nuclear Information System (INIS)

    1978-01-01

    This paper proposes technical and economic data and analysis for use in comparing the nuclear systems considered in INFCE. It suggests that a relatively detailed set of characteristics be developed for each system. An alternative to this approach is to concentrate on comparing the characteristic of most interest to INFCE, using a differential comparison to established systems (such as the LWR and HWR) where possible. This would avoid the repetitive analysis of design characteristics that are common to many systems. In making the INFCE comparisons it would still be appropriate that a selected set of information, pertinent to the primary assessment factors under consideration, be developed for each nuclear system. This selected set, much more limited than that set forth in the body of this paper, would include overall descriptions of the reactor and fuel cycle facilities, as well as specific information on resource utilization, flow of nuclear materials, and other areas to be determined by the Working Group. On the other hand, in areas such as costs, nuclear safety, and environmental impacts, it would not be intended that information be developed at a level of detail comparable to that resulting from a detailed design of each system being compared. Instead, the detailed set of data identified in this paper can serve as a check list to assure that all pertinent characteristics are considered, at least on a differential basis; more detailed assessments would be needed only where the differences have substantial impact. Thus this paper asks for more detail than will probably be appropriate for many contributed papers

  2. CTBT technical issues handbook

    International Nuclear Information System (INIS)

    Zucca, J.J.

    1994-05-01

    The purpose of this handbook is to give the nonspecialist in nuclear explosion physics and nuclear test monitoring an introduction to the topic as it pertains to a Comprehensive Test Ban Treaty (CTBT). The authors have tried to make the handbook visually oriented, with figures paired to short discussions. As such, the handbook may be read straight through or in sections. The handbook covers four main areas and ends with a glossary, which includes both scientific terms and acronyms likely to be encountered during CTBT negotiations. The following topics are covered: (1) Physics of nuclear explosion experiments. This is a description of basic nuclear physics and elementary nuclear weapon design. Also discussed are testing practices. (2) Other nuclear experiments. This section discusses experiments that produce small amounts of nuclear energy but differ from explosion experiments discussed in the first chapter. This includes the type of activities, such as laser fusion, that would continue after a CTBT is in force. (3) Monitoring tests in various environments. This section describes the different physical environments in which a test could be conducted (underground, in the atmosphere, in space, underwater, and in the laboratory); the sources of non-nuclear events (such as earthquakes and mining operations); and the opportunities for evasion. (4) On-site inspections. A CTBT is likely to include these inspections as an element of the verification provisions, in order to resolve the nature of ambiguous events. This chapter describes some technical considerations and technologies that are likely to be useful. (5) Selecting verification measures. This chapter discusses the uncertain nature of the evidence from monitoring systems and how compliance judgments could be made, taking the uncertainties into account. It also discusses how to allocate monitoring resources, given the likelihood of testing by various countries in various environments

  3. CTBT technical issues handbook

    Energy Technology Data Exchange (ETDEWEB)

    Zucca, J.J. [ed.

    1994-05-01

    The purpose of this handbook is to give the nonspecialist in nuclear explosion physics and nuclear test monitoring an introduction to the topic as it pertains to a Comprehensive Test Ban Treaty (CTBT). The authors have tried to make the handbook visually oriented, with figures paired to short discussions. As such, the handbook may be read straight through or in sections. The handbook covers four main areas and ends with a glossary, which includes both scientific terms and acronyms likely to be encountered during CTBT negotiations. The following topics are covered: (1) Physics of nuclear explosion experiments. This is a description of basic nuclear physics and elementary nuclear weapon design. Also discussed are testing practices. (2) Other nuclear experiments. This section discusses experiments that produce small amounts of nuclear energy but differ from explosion experiments discussed in the first chapter. This includes the type of activities, such as laser fusion, that would continue after a CTBT is in force. (3) Monitoring tests in various environments. This section describes the different physical environments in which a test could be conducted (underground, in the atmosphere, in space, underwater, and in the laboratory); the sources of non-nuclear events (such as earthquakes and mining operations); and the opportunities for evasion. (4) On-site inspections. A CTBT is likely to include these inspections as an element of the verification provisions, in order to resolve the nature of ambiguous events. This chapter describes some technical considerations and technologies that are likely to be useful. (5) Selecting verification measures. This chapter discusses the uncertain nature of the evidence from monitoring systems and how compliance judgments could be made, taking the uncertainties into account. It also discusses how to allocate monitoring resources, given the likelihood of testing by various countries in various environments.

  4. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Juan Camilo Serrano

    2011-12-16

    New and novel material and process technologies applied in wind blade designs and production are critical to increasing the competitiveness of wind power generation against traditional sources of energy. In this project, through collaboration between PPG Industries and MAG Industrial Automation Systems, the potential of using automated manufacturing for the production of fiber glass composite wind blades was evaluated from both technical and economic points of view. Further, it was demonstrated that by modifying the standard blade raw material forms through the use of cost effective pre-impregnated rovings coupled with using an automated fiber placement machine to lay up the parts, it is possible to produce state of the art composite laminates with significantly improved mechanical performance and with higher processing rates than standard blade production technology allows for today, thereby lowering the cost of energy over turbine blades made using traditional processes and materials. In conformity with the scope of work of the submitted proposal, the project team completed each task and documented and reported its findings on the appropriate quarterly report submitted to the DOE project team. The activities and this report are divided into 5 subtasks: (1) Material Investigation - Reviews traditional materials and key specifications and testing methods; (2) Manufacturing and Automation - Identifies new candidate material forms and automated layup processes; (3) Process Development - Performs trials of candidate materials and processes; (4) Predictive Analysis - Assesses impact of new material forms and automated processes on a model blade design; and (5) Feasibility Assessment - Compares traditional manufacturing processes and materials to new candidate material forms and automated processes.

  5. Engineering Technical Review Planning Briefing

    Science.gov (United States)

    Gardner, Terrie

    2012-01-01

    The general topics covered in the engineering technical planning briefing are 1) overviews of NASA, Marshall Space Flight Center (MSFC), and Engineering, 2) the NASA Systems Engineering(SE) Engine and its implementation , 3) the NASA Project Life Cycle, 4) MSFC Technical Management Branch Services in relation to the SE Engine and the Project Life Cycle , 5) Technical Reviews, 6) NASA Human Factor Design Guidance , and 7) the MSFC Human Factors Team. The engineering technical review portion of the presentation is the primary focus of the overall presentation and will address the definition of a design review, execution guidance, the essential stages of a technical review, and the overall review planning life cycle. Examples of a technical review plan content, review approaches, review schedules, and the review process will be provided and discussed. The human factors portion of the presentation will focus on the NASA guidance for human factors. Human factors definition, categories, design guidance, and human factor specialist roles will be addressed. In addition, the NASA Systems Engineering Engine description, definition, and application will be reviewed as background leading into the NASA Project Life Cycle Overview and technical review planning discussion.

  6. Field convergence between technical writers and technical translators

    DEFF Research Database (Denmark)

    Gnecchi, M.; Maylath, B.; Mousten, Birthe

    2011-01-01

    As translation of technical documents continues to grow rapidly and translation becomes more automated, the roles of professional communicators and translators appear to be converging. This paper updates preliminary findings first presented at the 2008 International Professional Communication...

  7. LHC Availability 2017: Technical Stop 1 to Technical Stop 2

    CERN Document Server

    Todd, Benjamin; Apollonio, Andrea; Walsh, David John; CERN. Geneva. ATS Department

    2017-01-01

    This document summarises the LHC machine availability for the period of Technical Stop 1 (TS1) to Technical Stop 2 (TS2) in 2017. This period was dedicated to proton physics with a bunch spacing of 25ns. This note has been produced and ratified by the Availability Working Group which has complied fault information for the period in question using the Accelerator Fault Tracker.

  8. Generalized instrumental variable models

    OpenAIRE

    Andrew Chesher; Adam Rosen

    2014-01-01

    This paper develops characterizations of identified sets of structures and structural features for complete and incomplete models involving continuous or discrete variables. Multiple values of unobserved variables can be associated with particular combinations of observed variables. This can arise when there are multiple sources of heterogeneity, censored or discrete endogenous variables, or inequality restrictions on functions of observed and unobserved variables. The models g...

  9. FINAL TECHNICAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Loren F. Goodrich

    2011-05-31

    NIST has played a key role in many of the one-on-one, domestic, and international interlaboratory comparisons of measurements on superconductors. The history of interlaboratory comparisons of measurements on superconductors tells us that careful measurement methods are needed to obtain consistent results. Inconsistent results can lead to many problems including: a mistrust of the results of others, unfair advantages in commerce, and erroneous feedback in the optimization of conductor performance. NIST has experience in many interlaboratory comparisons; a long-term commitment to measurement accuracy; and independent, third-party laboratory status. The principal investigator's direct involvement in the measurements and daily supervision of sample mounting is the unique situation that has allowed important discoveries and evolution of our capabilities over the last 30 years. The principal investigator's research and metrology has helped to improve the accuracy of critical-current (I{sub c}) measurements in laboratories throughout the world. As conductors continue to improve and design limits are tested, the continuation of the long-term commitment to measurement accuracy could be vitally important to the success of new conductor development programs. It is extremely important to the U.S. wire manufacturers to get accurate (high certainty) I{sub c} measurements in order to optimize conductor performance. The optimization requires the adjustment of several fabrication parameters (such as reaction time, reaction temperature, conductor design, doping, diffusion barrier, Cu to non-Cu ratio, and twist pitch) based on the I{sub c} measurement of the conductor. If the I{sub c} measurements are made with high variability, it may be unclear whether or not the parameters are being adjusted in the optimal direction or whether or not the conductor meets the target specification. Our metrology is vital to the U.S. wire manufacturers in the highly competitive international

  10. Innovative technical plasma applications

    International Nuclear Information System (INIS)

    Wintner, E.

    2013-01-01

    Plasma is the predominant status of matter, in stars as well as in interstellar space. In science, it was only recognized rather late as a specific (fourth) state of matter: Sir William Crookes described it in 1879 as “radiant matter”, Irving Langmuir created the name “plasma” in 1928. Technically generated plasma is employed very broadly in modern technology. Some examples are Plasma Displays, Fluorescent Lamps (also the modern Energy Saving Lamps), Corona Discharges (for e.g. Ozone generation, or even engine ignition), arc welding and cutting, reactive ion etching, mass spectroscopy, ion rocket engines and many more. Very early since the development of the laser, it was also employed to generate a plasma (spark) in air or on surfaces. Generally, for this purpose at least ns (“Giant”) pulses have to be used. In more recent times, pico- and femtosecond pulses have allowed to create plasma very easily and effectively. Laser fusion may represent the ultimate application in this direction, based on highly amplified ns pulses for inertial confinement or ps pulses designed as fast igniter. The idea of employing laser pulses for the ignition of engines was attempted for the first time in 1978, although with inadequate tools like the CO2 laser. After a long time of inactivity in this field, about 10 years ago a few institutions like Vienna University of Technology first resumed this approach with the help of modern type solid-state lasers and started systematic investigations around the idea of laser ignition of internal combustion engines. Now, this technique has reached a high degree of maturity; remaining problems lie on the development level and are to be solved soon. Ambitious product development by leading engine producers or ignition equipment suppliers has been started world-wide since several years and, as a result, in one or two years laser ignition will probably be imple-mented into high power gas engines or, somewhat later, high-priced automotive

  11. New functions for technical supervision

    Energy Technology Data Exchange (ETDEWEB)

    Herkommer, E.; Kressel, E.; Wollenschlaeger, M.

    1988-07-01

    The discussion concerns the foundation of a new Institution namely an 'Environmental Technical Inspection Board', in order to implement faster the technical and scientific findings in conservation and to control more efficiently the adherence to safety regulations. The article presents a review of the legal regulations in conservation, describes their constitutional status, tasks and legal status of the experts in the technical control societies, tasks and legal position of an environmental technical inspection board as well as its financing. It is stated that the execution deficit in pollution control can be decreased by better participation of experts and permanent control of all potentially dangerous installations. In order to realize this concept, the extension of already available structures presents itself, especially the consultation of officially approved experts, without a new administrative machinery having to be created. (orig./HSCH).

  12. Polar source analysis : technical memorandum

    Science.gov (United States)

    2017-09-29

    The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

  13. ATR Technical Specification Upgrade Program

    International Nuclear Information System (INIS)

    McCracken, R.T.; Durney, J.L.; Freund, G.A.

    1990-01-01

    The Advanced Test Reactor (ATR) is a 250 MW, uranium-aluminum fueled test reactor which began full power operation in 1969. The initial operation was controlled by an Operating Limits document based on the original Safety Analysis Report. Additional safety bases were later developed to support Technical Specifications which were approved and implemented in 1977. The Technical Specifications which were initially developed with content and format specified in ANSI/ANS--15.1, ''The Development of Technical Specifications for Research Reactors.'' The safety basis documentation and the Technical Specifications have been updated as required to maintain them current with the ATR facility configuration. All revisions have been made with a content, format and style consistent with the original. A major, two-phase program to upgrade the content, format and style is in progress. This paper describes the first phase of this program

  14. ATR technical specification upgrade program

    International Nuclear Information System (INIS)

    McCraken, R.T.; Durney, J.L.; Freund, G.A.

    1990-01-01

    The Advanced Test Reactor (ATR) is a 250 MW, uranium-aluminum fueled test reactor which began full power operation in 1969. The initial operation was controlled by an Operating Limits document based on the original Safety Analysis Report. Additional safety bases were later developed to support Technical Specifications which were approved and implemented in 1977. The Technical Specifications were initially developed with the content and format specified in ANSI/ANS-15.1, The Development of Technical Specifications for Research Reactors. The safety basis documentation and the Technical Specifications have been updated as required to maintain them current with the ATR facility configuration. All revisions have been made with a content, format and style consistent with the original. A major, two-phase program to upgrade the content, format and style is in progress. This paper describes the first phase of this program

  15. NASA Technical Reports Server (NTRS)

    Data.gov (United States)

    National Aeronautics and Space Administration — The NTRS is a valuable resource for researchers, students, educators, and the public to access NASA's current and historical technical literature and engineering...

  16. Hydrogen Storage Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The mission of the Hydrogen Storage Technical Team is to accelerate research and innovation that will lead to commercially viable hydrogen-storage technologies that meet the U.S. DRIVE Partnership goals.

  17. S-Chip Technical Assistance

    Data.gov (United States)

    U.S. Department of Health & Human Services — The page will provide access to reports and other published products designed to assist states with complicated S-Chip technical issues. The reports and products...

  18. Fuel Cell Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Fuel Cell Technical Team promotes the development of a fuel cell power system for an automotive powertrain that meets the U.S. DRIVE Partnership (United States Driving Research and Innovation for Vehicle efficiency and Energy sustainability) goals.

  19. Endogenous induced technical change and the costs of Kyoto

    International Nuclear Information System (INIS)

    Buonanno, Paolo; Carraro, Carlo; Galeotti, M.

    2001-09-01

    Many predictions and conclusions in the climate change literature have been made and drawn on the basis of theoretical analyses and quantitative models that are either static or that allow for simple forms of changes in technology, often along exogenously given time paths. It is therefore not clear a priori whether those conclusions and policy recipes still hold in the more realistic case of endogenously evolving technologies. In this paper, a quantitative tool with the features of an endogenous growth model is presented, which also accounts for the possibility that technical change can be induced by environmental policy measures. Both the output production technology and the emission-output ratio depend upon the stock of knowledge, which accumulates through R and D activities. R and D is thus an additional policy variable that comes into play along with pollution abatement and capital investment. Two versions of this climate model are studied, one with endogenous technical change but exogenous environmental technical change (i.e. no induced technical change) and the other with both endogenous and induced technical change. Hence, in both models technical change evolves endogenously as far as the production technology is concerned, but endogenous environmental (or induced) technical change is only accounted for in the second version. Finally, a third version of the model also captures technological spillover effects. As an application, the three versions of the model are simulated allowing for trade of pollution permits as specified in the Kyoto Protocol and assessing the implications in terms of cost efficiency, economic growth and R and D efforts of the three different specifications of technical change

  20. Technical management courses (before July)

    CERN Multimedia

    2015-01-01

    Please find below the courses in the field of technical management scheduled before July and which have places available.       For more details about a course and to register, please go to the Training Catalogue. If you need a course which is not in the catalogue, please contact your supervisor, your Departmental Training Officer or HR-LD at Technical.Management.Training@cern.ch.

  1. Technical framework for groundwater restoration

    International Nuclear Information System (INIS)

    1991-04-01

    This document provides the technical framework for groundwater restoration under Phase II of the Uranium Mill Tailings Remedial Action (UMTRA) Project. A preliminary management plan for Phase II has been set forth in a companion document titled ''Preplanning Guidance Document for Groundwater Restoration''. General principles of site characterization for groundwater restoration, restoration methods, and treatment are discussed in this document to provide an overview of standard technical approaches to groundwater restoration

  2. Guam Initial Technical Assessment Report

    Energy Technology Data Exchange (ETDEWEB)

    Baring-Gould, I.; Conrad, M.; Haase, S.; Hotchkiss, E.; McNutt, P.

    2011-04-01

    Under an interagency agreement, funded by the Department of Interior's (DOI) Office of Insular Affairs (OIA), the National Renewable Energy Laboratory (NREL) was tasked to deliver technical assistance to the island of Guam by conducting an island initial technical assessment that would lay out energy consumption and production data and establish a baseline. This assessment will be used to conduct future analysis and studies by NREL that will estimate energy efficiency and renewable energy potential for the island of Guam.

  3. International Technical Communication: Beyond Translation, Localization.

    Science.gov (United States)

    Klein, Fred

    1993-01-01

    Offers a personal view of international technical communication. Discusses computer-assisted translation, machine translation, machine interpreting, and the future of international technical communication. (SR)

  4. 78 FR 70569 - Technical Mapping Advisory Council

    Science.gov (United States)

    2013-11-26

    ...: FEMA-2013-0039] Technical Mapping Advisory Council AGENCY: Federal Emergency Management Agency, DHS... appointment to the Technical Mapping Advisory Council (TMAC). The notice incorrectly stated that contractors...

  5. Mobile Variable Depth Sampling System Design Study

    Energy Technology Data Exchange (ETDEWEB)

    BOGER, R.M.

    2000-08-25

    A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study.

  6. Mobile Variable Depth Sampling System Design Study

    International Nuclear Information System (INIS)

    BOGER, R.M.

    2000-01-01

    A design study is presented for a mobile, variable depth sampling system (MVDSS) that will support the treatment and immobilization of Hanford LAW and HLW. The sampler can be deployed in a 4-inch tank riser and has a design that is based on requirements identified in the Level 2 Specification (latest revision). The waste feed sequence for the MVDSS is based on Phase 1, Case 3S6 waste feed sequence. Technical information is also presented that supports the design study

  7. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Howe, Gary [RTI International, Research Triangle Park, NC (United States); Albritton, John [RTI International, Research Triangle Park, NC (United States); Denton, David [RTI International, Research Triangle Park, NC (United States); Turk, Brian [RTI International, Research Triangle Park, NC (United States); Gupta, Raghubir [RTI International, Research Triangle Park, NC (United States)

    2018-01-31

    technology has great potential to provide clean syngas from coal and petcoke-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.

  8. Reader-Centered Technical Writing

    Science.gov (United States)

    Narayanan, M.

    2012-12-01

    Technical writing is an essential part of professional communication and in recent years it has shifted from a genre-based approach. Formerly, technical writing primarily focused on generating templates of documents and sometimes it was creating or reproducing traditional forms with minor modifications and updates. Now, technical writing looks at the situations surrounding the need to write. This involves deep thinking about the goals and objectives of the project on hand. Furthermore, one observes that it is very important for any participatory process to have the full support of management. This support needs to be well understood and believed by employees. Professional writing may be very persuasive in some cases. When presented in the appropriate context, technical writing can persuade a company to improve work conditions ensuring employee safety and timely production. However, one must recognize that lot of professional writing still continues to make use of reports and instruction manuals. Normally, technical and professional writing addresses four aspects. Objective: The need for generating a given professionally written technical document and the goals the document is expected to achieve and accomplish. Clientele: The clientele who will utilize the technical document. This may include the people in the organization. This may also include "unintended readers." Customers: The population that may be affected by the content of the technical document generated. This includes the stakeholders who will be influenced. Environment: The background in which the document is created. Also, the nature of the situation that warranted the generation of the document. Swiss Psychologist Jean Piaget's view of Learning focuses on three aspects. The author likes to extend Jean Piaget's ideas to students, who are asked to prepare and submit Reader-Centered Technical Writing reports and exercises. Assimilation: Writers may benefit specifically, by assimilating a new object into

  9. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Peter Pilewskie

    2009-05-26

    period of time, the airborne method has the advantage of being quasi-instantaneous. Ten cases were found to be well suited for analysis using this gradient forcing method, and they exhibited a high degree of variability in the derived aerosol forcing efficiency, likely the result of changing aerosol characteristics with changing airmass during the experimental period. Over the integrated solar spectrum the mean instantaneous forcing was -135 W m{sup -2}. Converting to a 24 hour average, this equates to a forcing efficiency of -83 Wm{sup -2}, a magnitude similar to that observed during INDOEX. Variability among the cases examined was attributed to differences in aerosol single scattering albedo and this quantity was derived for each case based upon best fit between measured and modeled forcing efficiency. The details of this research have been summarized in a paper [Redemann, Pilewskie, et al., 2006].

  10. Variable importance in latent variable regression models

    NARCIS (Netherlands)

    Kvalheim, O.M.; Arneberg, R.; Bleie, O.; Rajalahti, T.; Smilde, A.K.; Westerhuis, J.A.

    2014-01-01

    The quality and practical usefulness of a regression model are a function of both interpretability and prediction performance. This work presents some new graphical tools for improved interpretation of latent variable regression models that can also assist in improved algorithms for variable

  11. Classifying variability modeling techniques

    NARCIS (Netherlands)

    Sinnema, Marco; Deelstra, Sybren

    Variability modeling is important for managing variability in software product families, especially during product derivation. In the past few years, several variability modeling techniques have been developed, each using its own concepts to model the variability provided by a product family. The

  12. Technical Support and Transfer of Geothrmal Technical Knowledge and Information

    Energy Technology Data Exchange (ETDEWEB)

    John W. Lund; Toni" Boyd

    2007-11-14

    The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

  13. CEEM Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Bowers, John [Univ. of California, Santa Barbara, CA (United States)

    2014-11-26

    concentrating photovoltaic applications thathave substantially higher efficiency than single substrate cells made of elemental semiconductors such as silicon. This task required the development of new cell bonding methods with excellent coupling of both photons and electrons between the sub-cells. To accomplish this, we developed (1) GaInN solar cells with enhanced performance by using quantum-well absorbers and front-surface optical texturing, (2) a hybrid "pillar-array" bond which uses an array of metal pillars for electrical coupling, and (3) a "hybrid moth-eye" optical coating which combines the benefits of nano-imprinted moth-eye coatings and traditional multilayer coatings. The technical effectiveness was assessed by measurement of the photovoltaic efficiency of solar cells made using these techniques; the ultrahigh efficiencies targeted by this work are of compelling economic value for concentrating photovoltaics.

  14. 47 CFR 18.207 - Technical report.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical report. 18.207 Section 18.207... Applications and Authorizations § 18.207 Technical report. When required by the Commission a technical report...(s) under which the equipment is or will be marketed. (e) A statement of the rated technical...

  15. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    KRIPPS, L.J.

    2005-03-03

    This document describes the qualitative evaluation of frequency and consequences for DST and SST representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant structures, systems and components (SSCs) and/or technical safety requirements (TSRs) were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support WP-13033, Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  16. Technical support and emergency centre

    International Nuclear Information System (INIS)

    Bohun, L.; Kapisovsk y, M.

    1997-01-01

    This paper presents technical support and emergency management center which will be on two places: Mochovce NPP Emergency Centre (Technical support center and Support working center) and Reserve Emergency Centre in Levice (Reserve emergency center and Environmental Evaluation Center). The main aims of the emergency management centers are: the management and coordination of all persons and organisations; provision of the all information needed to evaluation of the accident and its mitigation; continuous evaluation of the potential or real radiological consequences; taking measure for an early notification of the governmental bodies and the organizations, warning and protection of the public; and other aims. In the next part the data for technical support and emergency centre are discussed

  17. Plasma technology: a technical economical and political challenge

    International Nuclear Information System (INIS)

    Abreu, V.A. de; Vicente, L.C.; Bender, O.W.; Sanches Junior, O.

    1987-01-01

    To survey the State of the Art and Technic in Material, Process and Products by Plasma, it was needed to assemble economic, political and managerial variables that will affect the absortion and implantation of this technology in Brazil. Through a survey in industries, universities, research centers, energy agencies and financial and forster institutions it was possible to build a frame that gave us conditions to forecasting and suggest some mesures to Plasma sector. (author) [pt

  18. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements C: Employment. Technical Report 49C

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2009

    2009-01-01

    This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

  19. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements A: Demographics. Technical Report 49A

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2012

    2012-01-01

    This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

  20. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements D: Social. Technical Report 49D

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2009

    2009-01-01

    This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant…

  1. Technical innovation and policy of scientific technique

    International Nuclear Information System (INIS)

    Song, Wi Jin

    2006-04-01

    This book deals with system of innovation and policy of scientific technology : main view point and Topic, technical politics and technical learning, spread of internet and change of structure in information and communications industry, characteristic of technical innovation of software as open source, transfer into national innovation system, change of activity of public scientific technology, theory on technical innovation, evolution of technical innovation policy and participation of civil.

  2. Technical Manual: easyCBM. Technical Report #1408

    Science.gov (United States)

    Anderson, Daniel; Alonzo, Julie; Tindal, Gerald; Farley, Dan; Irvin, P. Shawn; Lai, Cheng-Fei; Saven, Jessica L.; Wray, Kraig A.

    2014-01-01

    Since the easyCBM© learning system was first published in 2006, over $8 million of federal funding (both from the Office of Special Education Programs and more recently from the Institute of Education Sciences) has been used to develop, study, and refine the assessments available on the system. This Technical Manual summarizes the ongoing research…

  3. Physical foundations of technical acoustics

    CERN Document Server

    Malecki, I

    1969-01-01

    Physical Foundations of Technical Acoustics discusses theoretical foundations of acoustical engineering. It is not so much a technical compendium as a systematic statement of physical laws so conceived that technologists might find in it all the information they need to become acquainted with the physical meaning and mathematical expression of phenomena they encounter in their work. To facilitate the acquirement of notions, which lie beyond a layman's grasp, the plan of narration adopted consists in beginning with the simplest idealized cases and then gradually moving on to the truest possibl

  4. System for technical innovation support

    International Nuclear Information System (INIS)

    2011-08-01

    This book lists field of support system, which includes tax, development work, basic research project, industrial technology, information and communications field, energy field, part and materials field, local industry, the small and medium business such as technical development field, and industry-university collaboration like summary of investment and financing support and guarantee, support of manpower such as brain pool and contact Korea, support of technique like development technology and strategy for patent, support on certification such as company and technical goods, purchase support.

  5. Management of technical information department

    International Nuclear Information System (INIS)

    Kim, T. H.; Han, D. H.; Moon, H. W.

    1997-03-01

    This report introduces technical information activities in 1996. They are composed of basic tasks and applied tasks. 1. Basic activities - acquisition, cataloging, and Information services 2. Management of KAERI-TIPS (Technical Information Processing System) 3. Construction of the database for nuclear-related Information 4. Role of Specialized Nuclear Information Center in the field of nuclear energy and cooperation with INIS section of IAEA 5. Beside above activities, in 1996 TID homepage was opened and online document delivery service was provided. (author). 25 tabs., 17 figs

  6. Technical progress and climatic change

    International Nuclear Information System (INIS)

    Ausubel, J.H.

    1995-01-01

    The global warming debate has neglected and thus underestimated the importance of technical change in considering reduction in greenhouse gases and adaptation to climate change. Relevant quantitative cases of long-run technical change during the past 100 years are presented in computing, communications, transport, energy, and agriculture. A noteworthy technological trajectory is that of decarbonization, or decreasing carbon intensity of primary energy. If human societies have not yet reached the end of the history of technology, the cost structure for mitigation and adaptation changes could be cheap. (Author)

  7. ITA technical activities status report

    International Nuclear Information System (INIS)

    Shimomura, Y.

    2004-01-01

    This note summarizes the progress made in the technical work of the ITER Transitional Arrangements in the period between September 2003 and June 2004. It comprises design work, update of baseline documents, risk management plan, ITER baseline web site, preparation of technical specifications, task agreements, international team status, CAD and document management, codes and standards, common expenses, future network connectivity needs, travel support of members of the International Team, testing blanket working group, physics status, diagnostics, task agreements for large physics R and D

  8. Management of technical information department

    Energy Technology Data Exchange (ETDEWEB)

    Kim, T. H.; Han, D. H.; Moon, H. W. [and others

    1997-03-01

    This report introduces technical information activities in 1996. They are composed of basic tasks and applied tasks. 1. Basic activities - acquisition, cataloging, and Information services 2. Management of KAERI-TIPS (Technical Information Processing System) 3. Construction of the database for nuclear-related Information 4. Role of Specialized Nuclear Information Center in the field of nuclear energy and cooperation with INIS section of IAEA 5. Beside above activities, in 1996 TID homepage was opened and online document delivery service was provided. (author). 25 tabs., 17 figs.

  9. Common Variable Immunodeficiency (CVID)

    Science.gov (United States)

    ... facebook share with twitter share with linkedin Common Variable Immunodeficiency (CVID) Primary Immune Deficiency Diseases (PIDDs) Primary ... PIDDs Genetics & Inheritance Talking to Your Doctor Common variable immunodeficiency (CVID) is characterized by low levels of ...

  10. Why technical-market research?

    Science.gov (United States)

    Lauglaug, A S

    1992-01-01

    Customers frequently need assistance in knowing what they want or might need. One process, technical-market research, helps understand the mind of the consumer so that the voice of the customer can be better translated into new products by designers, engineers, and marketers.

  11. Rio 2016 accessibility technical guidelines

    OpenAIRE

    2015-01-01

    This document combines the accessibility standards issued by the Brazilian Technical Standards Association (ABNT)* with the requirements of the International Paralympic Committee (IPC)’s Accessibility Guide and Brazilian laws, decrees and resolutions. The purpose of this publication is to guide the design, development and implementation of projects.

  12. Technical diagnostics of steam turbines

    International Nuclear Information System (INIS)

    Vlckova, B.; Drahy, J.

    1987-01-01

    This paper deals with practical experience in application of technical diagnostics methods to steam turbines, in particular using pedestal and shaft vibration measurements as well as estimation of bearing metal temperature and ultrasound emission signals. An estimation of effectiveness of the diagnostics methods used is given on the basis of experimental investigations made on a 30-MW turbine. (author)

  13. Socio-technical security metrics

    NARCIS (Netherlands)

    Gollmann, D.; Herley, C.; Koenig, V.; Pieters, W.; Sasse, M.A.

    2015-01-01

    Report from Dagstuhl seminar 14491. This report documents the program and the outcomes of Dagstuhl Seminar 14491 “Socio-Technical Security Metrics”. In the domain of safety, metrics inform many decisions, from the height of new dikes to the design of nuclear plants. We can state, for example, that

  14. TEcHNiCAL INNOVATION

    African Journals Online (AJOL)

    TEcHNiCAL INNOVATION. Anal venting after perianal surgery it ., Adeniran. Paediatric Surgery Unit, Department of Surgery, University of ilorin Teaching Hospital, ... Classification oiv anorectal malt'ormations~initial approach. Anal venting after perianal surgery. Adeniran J. O. diagnostic tests, and colostomy. Semin Pediatr ...

  15. Fifty years of Technical Cooperation

    International Nuclear Information System (INIS)

    2007-01-01

    The International Atomic Energy Agency (IAEA) was established in Vienna in 1957. The Statute of the IAEA, approved by 81 nations, founded the organization on three pillars: nuclear verification; safety and security; and the transfer of technology. Today, these three pillars still remain at the heart of the organization's work. However, the way in which the IAEA carries out this work, particularly with regard to technology transfer, has changed greatly over the years. When the IAEA opened for business, nuclear science and technology were in their infancy. Many Member States had no nuclear capacity at all. The IAEA's 'technical assistance' programme, as it was then known, was modest. Early projects were small in scale and short lived, focusing mainly on building human capacities and creating institutions and facilities that would support the introduction of nuclear technology in a safe and effective manner. Today, the picture is more complex. Instead of merely offering assistance, the IAEA focuses on cooperation for sustainable socioeconomic development, building on the skills and infrastructure that Member States have acquired over the past five decades. Member States are full partners in the process, guiding the IAEA's technical cooperation activities, setting national and regional priorities, and offering training opportunities and technical support to the IAEA and to other Member States. Technical cooperation between developing countries is facilitated and supported through regional cooperative agreements. Regional centres of expertise play an important role in sharing the benefits of nuclear science and technology among Member States

  16. Reforming Technical and Technological Education.

    Science.gov (United States)

    Wilson, David N.

    1993-01-01

    Review of technical and technological educational reform in Brazil, Canada, Germany, Great Britain, Indonesia, Malaysia, Singapore, and Sweden shows that reform takes time to complete effectively, long-term approaches are needed, and reform is linked to industrial development, regional cooperation, and decentralized decision making. (SK)

  17. NWMO transportation technical work program

    International Nuclear Information System (INIS)

    Hatton, C.

    2015-01-01

    This paper describes technical work program for the transportation nuclear waste by the Nuclear Waste Management Organization (NWMO). Transportation work program involves risk assessment which under normal conditions involves dose assessment to the worker and the public as well as consideration of transportation system routing and operations. It also involves possible accident scenarios using forensic modelling and probability analysis.

  18. Career Satisfaction Following Technical Education

    Science.gov (United States)

    McDonald, Betty Manager

    2011-01-01

    The effect of career and technical education in the Caribbean is an area of intervention research that needs more attention. This present research is the first of its kind within the region. The study benefits from a large sample size (N = 500) conducted among a non-traditional population in the field of career development. This paper reports on…

  19. 77 FR 32465 - Technical Standards

    Science.gov (United States)

    2012-06-01

    ... corruption in the Class II gaming system software. One commenter stated that many of the requirements cannot... regulation went into effect in 2008 and all Class II gaming systems, with the exception of grandfathered... Commission notes that this has been a requirement since the current technical standards went into effect in...

  20. A Taxonomy of Technical Animation

    OpenAIRE

    D. Vaněček; J. Jirsa

    2011-01-01

    The age in which we are living nowadays is characterized by rapid innovation in the development of information and communication technologies (ICT). This innovation has a significant influence on the education process. This article deals with computer animation in technical education. Our aim is to show the taxonomy of education animation. The paper includes practical examples of animation.

  1. A Taxonomy of Technical Animation

    Directory of Open Access Journals (Sweden)

    D. Vaněček

    2011-01-01

    Full Text Available The age in which we are living nowadays is characterized by rapid innovation in the development of information and communication technologies (ICT. This innovation has a significant influence on the education process. This article deals with computer animation in technical education. Our aim is to show the taxonomy of education animation. The paper includes practical examples of animation.

  2. Consolidated incineration facility technical support

    International Nuclear Information System (INIS)

    Burns, D.; Looper, M.G.

    1993-01-01

    In 1996, the Savannah River Site plans to begin operation of the Consolidated Incineration Facility (CIF) to treat solid and liquid RCRA hazardous and mixed wastes. The Savannah River Technology Center (SRTC) leads an extensive technical support program designed to obtain incinerator and air pollution control equipment performance data to support facility start-up and operation. Key components of this technical support program include recently completed waste burn tests at both EPA's Incineration Research Facility and at Energy and Environmental Research Corporation's Solid Waste Incineration Test Facility. The main objectives for these tests were determining the fate of heavy metals, measuring organics destruction and removal efficiencies, and quantifying incinerator offgas particulate loading and size distribution as a function of waste feed characteristics and incineration conditions. In addition to these waste burning tests, the SRTC has recently completed installations of the Offgas Components Test Facility (OCTF), a 1/10 scale CIF offgas system pilot plant. This pilot facility will be used to demonstrate system operability and maintainability, evaluate and optimize equipment and instrument performance, and provide direct CIF start-up support. Technical support programs of this type are needed to resolve technical issues related with treatment and disposal of combustible hazardous, mixed, and low-level radioactive waste. Implementation of this program will minimize facility start-up problems and help insure compliance with all facility performance requirements

  3. Mechanical Engineering Department technical review

    Energy Technology Data Exchange (ETDEWEB)

    Carr, R.B.; Abrahamson, L.; Denney, R.M.; Dubois, B.E (eds.)

    1982-01-01

    Technical achievements and publication abstracts related to research in the following Divisions of Lawrence Livermore Laboratory are reported in this biannual review: Nuclear Fuel Engineering; Nuclear Explosives Engineering; Weapons Engineering; Energy Systems Engineering; Engineering Sciences; Magnetic Fusion Engineering; and Material Fabrication. (LCL)

  4. DOE FINAL TECHNICAL REPORT RP

    Energy Technology Data Exchange (ETDEWEB)

    RUSS PETERMAN

    2012-01-01

    The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

  5. Career Technical Education Pathways Initiative

    Science.gov (United States)

    California Community Colleges, Chancellor's Office, 2013

    2013-01-01

    California's education system--the largest in the United States--is an essential resource for ensuring strong economic growth in the state. The Career Technical Education Pathways Initiative (referred to as the Initiative in this report), which became law in 2005, brings together community colleges, K-12 school districts, employers, organized…

  6. Design mentoring tool : [technical summary].

    Science.gov (United States)

    2011-01-01

    In 2004 a design engineer on-line mentoring tool was developed and implemented The purpose of the tool was to assist senior engineers mentoring new engineers to the INDOT design process and improve their technical competency. This approach saves seni...

  7. [Technical medicine in ancient comedy].

    Science.gov (United States)

    Rodríguez Alfageme, I

    1995-01-01

    The texts of Greek comedy offer a panoramic vision of the evolution of medicine between the fifth and the third centuries. They provide an excellent way to understand the prejudices and the bases of technical medicine and its relationship with popular medicine. Comedy also shows us a vivid portrait of the physician and his position in Greek society.

  8. 76 FR 80226 - Technical Amendments

    Science.gov (United States)

    2011-12-23

    ... final rule, effective upon publication. Generally, the Administrative Procedure Act (APA) requires a.... Additionally, the APA requires that a final rule must have a delayed effective date of 30 days from the date of... delayed effective date requirement under the APA. 5 U.S.C. 553(d)(3). Again the technical change conforms...

  9. Solar energy technical training directory

    Energy Technology Data Exchange (ETDEWEB)

    Corcoleotes, G; Kramer, K; O& #x27; Connor, K

    1979-06-01

    Available solar energy offerings in the technical training area are presented. Institutions are listed alphabetically by state. Each listing includes an institution address and phone number, solar programs or curricula offered, and detailed solar couse information. An alphabetical index of institutions in included. (MHR)

  10. 77 FR 39899 - Technical Corrections

    Science.gov (United States)

    2012-07-06

    ... requirements, Source material, Special nuclear material, Waste treatment and disposal. 10 CFR Part 21 Nuclear... Atomic Energy Act sec. 274 (42 U.S.C. 2021) and under Nuclear Waste Policy Act sec. 121 (42 U.S.C. 10141... NUCLEAR REGULATORY COMMISSION 10 CFR Chapter I [NRC-2012-0092] RIN 3150-AJ16 Technical Corrections...

  11. Standard Technical Specifications, Westinghouse plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (STS) for Westinghouse Plants and documents the positions of the Nuclear Regulatory Commission based on the Westinghouse Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. This document, Volume 1, contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

  12. Defense Technical Information Center thesaurus

    Energy Technology Data Exchange (ETDEWEB)

    Dickert, J.H. [ed.] [comp.

    1996-10-01

    This DTIC Thesaurus provides a basic multidisciplinary subject term vocabulary used by DTIC to index and retrieve scientific and technical information from its various data bases and to aid DTIC`s users in their information storage and retrieval operations. It includes an alphabetical posting term display, a hierarchy display, and a Keywork Out of Context (KWOC) display.

  13. Hydrogen Delivery Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The mission of the Hydrogen Delivery Technical Team (HDTT) is to enable the development of hydrogen delivery technologies, which will allow for fuel cell competitiveness with gasoline and hybrid technologies by achieving an as-produced, delivered, and dispensed hydrogen cost of $2-$4 per gallon of gasoline equivalent of hydrogen.

  14. Technical assistance contractor Management Plan

    International Nuclear Information System (INIS)

    1993-09-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins ampersand Beckwith Agra, Inc. (SHB Agra), and Geraghty ampersand Miller, Inc. (G ampersand M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC's groundwater technical breadth and depth, so G ampersand M was brought in to augment the team's capabilities. The TAC contract's scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC's management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls

  15. Amplification factor variable amplifier

    NARCIS (Netherlands)

    Akitsugu, Oshita; Nauta, Bram

    2007-01-01

    PROBLEM TO BE SOLVED: To provide an amplification factor variable amplifier capable of achieving temperature compensation of an amplification factor over a wide variable amplification factor range. ; SOLUTION: A Gilbert type amplification factor variable amplifier 11 amplifies an input signal and

  16. Amplification factor variable amplifier

    NARCIS (Netherlands)

    Akitsugu, Oshita; Nauta, Bram

    2010-01-01

    PROBLEM TO BE SOLVED: To provide an amplification factor variable amplifier capable of achieving temperature compensation of an amplification factor over a wide variable amplification factor range. ;SOLUTION: A Gilbert type amplification factor variable amplifier 11 amplifies an input signal and can

  17. Technical noise supplement : TeNS : a technical supplement to the Traffic Noise Analysis Protocol.

    Science.gov (United States)

    1998-10-01

    The purpose of this Technical Noise Supplement (TeNS) is to provide technical background : information on transportation-related noise in general and highway traffic noise in : particular. It is designed to elaborate on technical concepts and procedu...

  18. Soil variability in engineering applications

    Science.gov (United States)

    Vessia, Giovanna

    2014-05-01

    Natural geomaterials, as soils and rocks, show spatial variability and heterogeneity of physical and mechanical properties. They can be measured by in field and laboratory testing. The heterogeneity concerns different values of litho-technical parameters pertaining similar lithological units placed close to each other. On the contrary, the variability is inherent to the formation and evolution processes experienced by each geological units (homogeneous geomaterials on average) and captured as a spatial structure of fluctuation of physical property values about their mean trend, e.g. the unit weight, the hydraulic permeability, the friction angle, the cohesion, among others. The preceding spatial variations shall be managed by engineering models to accomplish reliable designing of structures and infrastructures. Materon (1962) introduced the Geostatistics as the most comprehensive tool to manage spatial correlation of parameter measures used in a wide range of earth science applications. In the field of the engineering geology, Vanmarcke (1977) developed the first pioneering attempts to describe and manage the inherent variability in geomaterials although Terzaghi (1943) already highlighted that spatial fluctuations of physical and mechanical parameters used in geotechnical designing cannot be neglected. A few years later, Mandelbrot (1983) and Turcotte (1986) interpreted the internal arrangement of geomaterial according to Fractal Theory. In the same years, Vanmarcke (1983) proposed the Random Field Theory providing mathematical tools to deal with inherent variability of each geological units or stratigraphic succession that can be resembled as one material. In this approach, measurement fluctuations of physical parameters are interpreted through the spatial variability structure consisting in the correlation function and the scale of fluctuation. Fenton and Griffiths (1992) combined random field simulation with the finite element method to produce the Random

  19. A Theory of Sex Differences in Technical Aptitude and Some Supporting Evidence.

    Science.gov (United States)

    Schmidt, Frank L

    2011-11-01

    In this article, I present a theory that explains the origin of sex differences in technical aptitudes. The theory takes as proven that there are no sex differences in general mental ability (GMA), and it postulates that sex differences in technical aptitude (TA) stem from differences in experience in technical areas, which is in turn based on sex differences in technical interests. Using a large data set, I tested and found support for four predictions made by this theory: (a) the construct level correlation between technical aptitude and GMA is larger for females than males, (b) the observed and true score variability of technical aptitude is greater among males than females, (c) at every level of GMA females have lower levels of technical aptitude, and (d) technical aptitude measures used as estimates of GMA for decision purposes would result in underestimation of GMA levels for girls and women. Given that GMA carries the weight of prediction of job performance, the support found for this last prediction suggests that, for many jobs, technical aptitude tests may underpredict the job performance of female applicants and employees. Future research should examine this question. © Association for Psychological Science 2011.

  20. Technical Efficiency of Automotive Industry Cluster in Chennai

    Science.gov (United States)

    Bhaskaran, E.

    2012-07-01

    Chennai is also called as Detroit of India due to its automotive industry presence producing over 40 % of the India's vehicle and components. During 2001-2002, diagnostic study was conducted on the Automotive Component Industries (ACI) in Ambattur Industrial Estate, Chennai and in SWOT analysis it was found that it had faced problems on infrastructure, technology, procurement, production and marketing. In the year 2004-2005 under the cluster development approach (CDA), they formed Chennai auto cluster, under public private partnership concept, received grant from Government of India, Government of Tamil Nadu, Ambattur Municipality, bank loans and stake holders. This results development in infrastructure, technology, procurement, production and marketing interrelationships among ACI. The objective is to determine the correlation coefficient, regression equation, technical efficiency, peer weights, slack variables and return to scale of cluster before and after the CDA. The methodology adopted is collection of primary data from ACI and analyzing using data envelopment analysis (DEA) of input oriented Banker-Charnes-Cooper model. There is significant increase in correlation coefficient and the regression analysis reveals that for one percent increase in employment and net worth, the gross output increases significantly after the CDA. The DEA solver gives the technical efficiency of ACI by taking shift, employment, net worth as input data and quality, gross output and export ratio as output data. From the technical score and ranking of ACI, it is found that there is significant increase in technical efficiency of ACI when compared to CDA. The slack variables obtained clearly reveals the excess employment and net worth and no shortage of gross output. To conclude there is increase in technical efficiency of not only Chennai auto cluster in general but also Chennai auto components industries in particular.

  1. Technical communication: Perspectives for the eighties

    Science.gov (United States)

    Mathes, J. C.; Pinelli, T. E.

    The proceeding suggest that technical communication has become an important subfield and is becoming an intrinsic part of many undergraduate curricula. Technical communication as a separate discipline, however, is relatively new. For that reason, proceedings that can make current research available as quickly as possible are suggested for preparation. The following topics were addressed: (1) a history and definition of technical writing, (2) the case method is technical communication (3) teaching technical writing (4) oral communication and rhetorical theory, and (5) new approaches in and practical applications of technical writing.

  2. Variable mechanical ventilation.

    Science.gov (United States)

    Fontela, Paula Caitano; Prestes, Renata Bernardy; Forgiarini, Luiz Alberto; Friedman, Gilberto

    2017-01-01

    To review the literature on the use of variable mechanical ventilation and the main outcomes of this technique. Search, selection, and analysis of all original articles on variable ventilation, without restriction on the period of publication and language, available in the electronic databases LILACS, MEDLINE®, and PubMed, by searching the terms "variable ventilation" OR "noisy ventilation" OR "biologically variable ventilation". A total of 36 studies were selected. Of these, 24 were original studies, including 21 experimental studies and three clinical studies. Several experimental studies reported the beneficial effects of distinct variable ventilation strategies on lung function using different models of lung injury and healthy lungs. Variable ventilation seems to be a viable strategy for improving gas exchange and respiratory mechanics and preventing lung injury associated with mechanical ventilation. However, further clinical studies are necessary to assess the potential of variable ventilation strategies for the clinical improvement of patients undergoing mechanical ventilation.

  3. Technical efficiency under alternative environmental regulatory regimes: The case of Dutch horticulture

    International Nuclear Information System (INIS)

    Van der Vlist, Arno J.; Withagen, Cees; Folmer, Henk

    2007-01-01

    We consider the performance of small and medium sized enterprises in Dutch horticulture under different environmental policy regimes across time. We address the question whether technical performance differs under these alternative regulatory regimes to test Porter's hypothesis that stricter environmental regulation reduces technical inefficiency. For this purpose, we use a stochastic production frontier framework allowing for inclusion of policy variables to measure the effect of alternative environmental policy regimes on firms' performance. The main result is that stricter environmental policy regimes have indeed reduced technical inefficiencies in Dutch horticulture. The estimation results indicate amongst others that the 1997 agreement on energy, nutrient and pesticides use enhances technical efficiency. Firms under the strict environmental policy regime are found to be more technically efficient than those under a lax regime, thereby supporting the claims by Porter and Van der Linde (Porter, M., Van der Linde, C., 1995. Green and Competitive: Ending the stalemate. Harvard Business Review 73, pp. 120-137) concerning Dutch horticulture. (author)

  4. Does Technical Success of Angioplasty in Dysfunctional Hemodialysis Accesses Correlate with Access Patency?

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, Arshdeep; Tan, Kong T.; Noel-Lamy, Maxime; Simons, Martin E.; Rajan, Dheeraj K., E-mail: dheeraj.rajan@uhn.ca [University Health Network, University of Toronto, Division of Vascular and Interventional Radiology, Peter Munk Cardiac Center (Canada)

    2016-10-15

    PurposeTo study if <30 % residual stenosis post angioplasty (PTA) correlates with primary access circuit patency, and if any variables predict technical success.Materials and MethodsA prospective observational study was performed between January 2009 and December 2012, wherein 76 patients underwent 154 PTA events in 56 prosthetic grafts (AVG) and 98 autogenous fistulas (AVF). Data collected included patient age, gender, lesion location and laterality, access type and location, number of prior interventions, and transonic flow rates pre- and postintervention. Impact of technical outcome on access patency was assessed. Univariate logistic regression was used to assess the impact of variables on technical success with significant factors assessed with a multiple variable model.ResultsTechnical success rates of PTA in AVFs and AVGs were 79.6 and 76.7 %, respectively. Technical failures of PTA were associated with an increased risk of patency loss among circuits with AVFs (p < 0.05), but not with AVGs (p = 0.7). In AVFs, primary access patency rates between technical successes and failures at three and 6 months were 74.4 versus 61.9 % (p = 0.3) and 53.8 versus 23.8 % (p < 0.05), respectively. In AVGs, primary access patency rates between technical successes and failures at three and six months were 72.1 versus 53.9 % (p = 0.5) and 33.6 versus 38.5 % (p = 0.8), respectively. Transonic flow rates did not significantly differ among technically successful or failed outcomes at one or three months.ConclusionTechnical failures of PTA had a significant impact on access patency among AVFs with a trend toward poorer access patency within AVGs.

  5. Does Technical Success of Angioplasty in Dysfunctional Hemodialysis Accesses Correlate with Access Patency?

    International Nuclear Information System (INIS)

    Sidhu, Arshdeep; Tan, Kong T.; Noel-Lamy, Maxime; Simons, Martin E.; Rajan, Dheeraj K.

    2016-01-01

    PurposeTo study if <30 % residual stenosis post angioplasty (PTA) correlates with primary access circuit patency, and if any variables predict technical success.Materials and MethodsA prospective observational study was performed between January 2009 and December 2012, wherein 76 patients underwent 154 PTA events in 56 prosthetic grafts (AVG) and 98 autogenous fistulas (AVF). Data collected included patient age, gender, lesion location and laterality, access type and location, number of prior interventions, and transonic flow rates pre- and postintervention. Impact of technical outcome on access patency was assessed. Univariate logistic regression was used to assess the impact of variables on technical success with significant factors assessed with a multiple variable model.ResultsTechnical success rates of PTA in AVFs and AVGs were 79.6 and 76.7 %, respectively. Technical failures of PTA were associated with an increased risk of patency loss among circuits with AVFs (p < 0.05), but not with AVGs (p = 0.7). In AVFs, primary access patency rates between technical successes and failures at three and 6 months were 74.4 versus 61.9 % (p = 0.3) and 53.8 versus 23.8 % (p < 0.05), respectively. In AVGs, primary access patency rates between technical successes and failures at three and six months were 72.1 versus 53.9 % (p = 0.5) and 33.6 versus 38.5 % (p = 0.8), respectively. Transonic flow rates did not significantly differ among technically successful or failed outcomes at one or three months.ConclusionTechnical failures of PTA had a significant impact on access patency among AVFs with a trend toward poorer access patency within AVGs.

  6. Technical Efficiency in the Chilean Agribusiness Sector - a Stochastic Meta-Frontier Approach

    OpenAIRE

    Larkner, Sebastian; Brenes Muñoz, Thelma; Aedo, Edinson Rivera; Brümmer, Bernhard

    2013-01-01

    The Chilean economy is strongly export-oriented, which is also true for the Chilean agribusiness industry. This paper investigates the technical efficiency of the Chilean food processing industry between 2001 and 2007. We use a dataset from the 2,471 of firms in food processing industry. The observations are from the ‘Annual National Industrial Survey’. A stochastic meta-frontier approach is used in order to analyse the drivers of technical efficiency. We include variables capturing the effec...

  7. Correction of technical bias in clinical microarray data improves concordance with known biological information

    DEFF Research Database (Denmark)

    Eklund, Aron Charles; Szallasi, Zoltan Imre

    2008-01-01

    The performance of gene expression microarrays has been well characterized using controlled reference samples, but the performance on clinical samples remains less clear. We identified sources of technical bias affecting many genes in concert, thus causing spurious correlations in clinical data...... sets and false associations between genes and clinical variables. We developed a method to correct for technical bias in clinical microarray data, which increased concordance with known biological relationships in multiple data sets....

  8. State Variability in Supply of Office-based Primary Care Providers: United States, 2012

    Science.gov (United States)

    ... Order from the National Technical Information Service NCHS State Variability in Supply of Office-based Primary Care Providers: United States, 2012 Recommend on Facebook Tweet Share Compartir NCHS ...

  9. Technical Training seminar: Texas Instruments

    CERN Multimedia

    2006-01-01

    Monday 6 November TECHNICAL TRAINING SEMINAR 14:00 to 17:30 - Training Centre Auditorium (bldg. 593) Texas Instruments Technical Seminar Michael Scholtholt, Field Application Engineer / TEXAS INSTRUMENTS (US, D, CH) POWER - A short approach to Texas Instruments power products Voltage mode vs. current mode control Differentiating DC/DC converters by analyzing control and compensation schemes: line / load regulation, transient response, BOM, board space, ease-of-use Introduction to the SWIFT software FPGA + CPLD power solutions WIRELESS / CHIPCON Decision criteria when choosing a RF platform Introduction to Texas Instruments wireless products: standardized platforms proprietary platforms ( 2.4 GHz / sub 1 GHz) development tools Antenna design: example for 2.4 GHz questions, discussion Industrial partners: Robert Medioni, François Caloz / Spoerle Electronic, CH-1440 Montagny (VD), Switzerland Phone: +41 24 447 0137, email: RMedioni@spoerle.com, http://www.spoerle.com Language: English. Free s...

  10. Internal dosimetry technical basis manual

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-20

    The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs.

  11. Internal dosimetry technical basis manual

    International Nuclear Information System (INIS)

    1990-01-01

    The internal dosimetry program at the Savannah River Site (SRS) consists of radiation protection programs and activities used to detect and evaluate intakes of radioactive material by radiation workers. Examples of such programs are: air monitoring; surface contamination monitoring; personal contamination surveys; radiobioassay; and dose assessment. The objectives of the internal dosimetry program are to demonstrate that the workplace is under control and that workers are not being exposed to radioactive material, and to detect and assess inadvertent intakes in the workplace. The Savannah River Site Internal Dosimetry Technical Basis Manual (TBM) is intended to provide a technical and philosophical discussion of the radiobioassay and dose assessment aspects of the internal dosimetry program. Detailed information on air, surface, and personal contamination surveillance programs is not given in this manual except for how these programs interface with routine and special bioassay programs

  12. Mechanical Engineering Department technical abstracts

    Energy Technology Data Exchange (ETDEWEB)

    1984-07-01

    The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division.

  13. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    KRIPPS, L.J.

    2005-02-18

    This document describes the qualitative evaluation of frequency and consequences for double shell tank (DST) and single shell tank (SST) representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant SSCs and/or TSRS were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  14. Technical aspects of fuel reprocessing

    International Nuclear Information System (INIS)

    Groenier, W.S.

    1982-02-01

    The purpose of this paper is to present a brief description of fuel reprocessing and some present developments which show the reliability of nuclear energy as a long-term supply. The following topics are discussed: technical reasons for reprocessing; economic reasons for reprocessing; past experience; justification for advanced reprocessing R and D; technical aspects of current reprocessing development. The present developments are mainly directed at the reprocessing of breeder reactor fuels but there are also many applications to light-water reactor fuel reprocessing. These new developments involve totally remote operation, and maintenance. To demonstrate this advanced reprocessing concept, pilot-scale demonstration facilities are planned with commercial application occurring sometime after the year 2000

  15. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    1984-01-01

    The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division

  16. TRManager – Technical Risk Manager

    Directory of Open Access Journals (Sweden)

    Mark A. Gregory

    2009-06-01

    Full Text Available This paper presents research into the development of a new information management technique called Technical Risk Manager. Project management involves the use of processes and information management techniques to aid decision making in the pursuit of project success. Project success may be achieved by meeting time, cost or performance criteria. Current project management practices focus on achieving time and cost project success criteria by using three information management techniques developed in the 1950s: Gantt, PERT and Critical Path Method. Technical Risk Manager has been developed to provide an information management technique that may be used to aid project management decision making in the pursuit of achieving the performance project success criteria.

  17. Linac4 Technical Design Report

    CERN Document Server

    Arnaudon, L; Baylac, M; Bellodi, G; Body, Y; Borburgh, J; Bourquin, P; Broere, J; Brunner, O; Bruno, L; Carli, C; Caspers, Friedhelm; Cousineau, S M; Cuvet, Y; De Almeida Martins, C; Dobers, T; Fowler, T; Garoby, R; Gerigk, F; Goddard, B; Hanke, K; Hori, M; Jones, M; Kahle, K; Kalbreier, Willi; Kroyer, T; Küchler, D; Lombardi, A M; López-Hernandez, L A; Magistris, M; Martini, M; Maury, S; Page, E; Paoluzzi, M; Pasini, M; Raich, U; Rossi, C; Royer, J P; Sargsyan, E; Serrano, J; Scrivens, R; Silari, M; Timmins, M; Venturini-Delsolaro, W; Vretenar, M; Wegner, R; Weterings, W; Zickler, T

    2006-01-01

    Linac4 is an H- linear accelerator, intended to replace Linac2 as injector to the PS Booster (PSB). By delivering to the PSB a beam at 160 MeV energy, Linac4 will provide the conditions to double the brightness and intensity of the beam from the PSB, thus removing the first bottleneck towards higher brightness for the LHC and simplifying operation. Moreover, this new linac constitutes an essential component of any of the envisaged LHC upgrade scenarios and could open the way to future extensions of the CERN accelerator complex towards higher performance. This Technical Design Report presents a detailed technical overview of the Linac4 design as it stands at end 2006.

  18. Radiation sources and technical services

    International Nuclear Information System (INIS)

    Stonek, K.; Satorie, Z.; Vyskocil, I.

    1981-01-01

    Work is briefly described of the department for sealed sources production of the Institute, including leak testing and surface contamination of sealed sources. The department also provides technical services including the inspections of sealed sources used in medicine and geology and repair of damaged sources. It carries out research of the mechanical and thermal strength of sealed sources and of the possibility of reprocessing used 226 Ra sources. The despatch department is responsible for supplying the entire country with home and imported radionuclides. The department of technical services is responsible for testing imported radionuclides, assembling materials testing, industrial and medical irradiation devices, and for the collection and storage of low-level wastes on a national scale. (M.D.)

  19. Tank waste technical options report

    International Nuclear Information System (INIS)

    Boomer, K.D.; Baker, S.K.; Boldt, A.L.; Galbraith, J.D.; Garfield, J.S.; Golberg, C.E.; Higley, B.A.; Johnson, L.J.; Kupfer, M.J.; Marusich, R.M.; Parazin, R.J.; Praga, A.N.; Reddick, G.W.; Reddick, J.A.; Slaathaug, E.J.; Swanson, L.M.; Waldo, T.L.; Worcester, C.E.

    1993-01-01

    This document, Tank Waste Technical Options Report, assesses technologies that can be applied to treat and dispose of all Hanford Site tank waste including the cesium and strontium capsules. This effort continues the single-shell tank systems engineering work that began at the urging of a National Academy of Science subpanel. The study develops data on specific technologies that are combined to form alternativesfor waste treatment and disposal. These alternatives are defined and evaluated in the Tank Waste Decision Analysis Report. Both studies are an integral part of the Tank Waste Remediation System goal of defininga new technical strategy in 1993. The engineering work represented in this document will also serve as data for the environmental impact statement support document

  20. Improving Technical Instruction Using Personality Styles.

    Science.gov (United States)

    Tomal, Daniel R.

    2003-01-01

    Incorporating personality styles into technical instruction can enhance student learning. Four personality styles based on Jung--intuitor, feeler, thinker, and doer--have implications for individualizing technical instruction. (JOW)

  1. Works Technical Department progress report, August 1965

    Energy Technology Data Exchange (ETDEWEB)

    1965-09-17

    This document details the activities of the Savannah River Works Technical Department during the month of August 1965. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  2. 76 FR 71011 - Reliability Technical Conference Agenda

    Science.gov (United States)

    2011-11-16

    ... through http://www.ferc.gov . Anyone with Internet access who desires to listen to this event can do so by.... Kimberly D. Bose, Secretary. Reliability Technical Conference Commissioner-Led Reliability Technical...

  3. 78 FR 38311 - Reliability Technical Conference Agenda

    Science.gov (United States)

    2013-06-26

    ....gov . Anyone with Internet access who desires to listen to this event can do so by navigating to www...] [TIFF OMITTED] TN26JN13.000 Reliability Technical Conference Commissioner-Led Reliability Technical...

  4. Objective assessment of technical skills in surgery

    OpenAIRE

    Moorthy, Krishna; Munz, Yaron; Sarker, Sudip K; Darzi, Ara

    2003-01-01

    In the past few years, considerable developments have been made in the objective assessment of technical proficiency of surgeons. Technical skills should be assessed during training, and various methods have been developed for this purpose

  5. Works Technical Department progress report, March 1961

    Energy Technology Data Exchange (ETDEWEB)

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  6. Summary of Sandia Laboratories technical capabilities

    International Nuclear Information System (INIS)

    1977-05-01

    The technical capabilities of Sandia Laboratories are detailed in a series of companion reports. In this summary the use of the capabilities in technical programs is outlined and the capabilities are summarized. 25 figures, 3 tables

  7. Who Recognises Technical Standards in TTIP?

    NARCIS (Netherlands)

    K.P. Purnhagen (Kai)

    2017-01-01

    textabstractCurrent political discussions on the relationship of technical standards to the Transatlantic, Trade and Investment Partnership (TTIP) concern the question whether TTIP can provide a transatlantic level playing field for technical standards, and whether this will negatively affect

  8. Technical center for transportation analyses

    International Nuclear Information System (INIS)

    Foley, J.T.

    1978-01-01

    A description is presented of an information search/retrieval/research activity of Sandia Laboratories which provides technical environmental information which may be used in transportation risk analyses, environmental impact statements, development of design and test criteria for packaging of energy materials, and transportation mode research studies. General activities described are: (1) history of center development; (2) environmental information storage/retrieval system; (3) information searches; (4) data needs identification; and (5) field data acquisition system and applications

  9. System for Users Technical Support

    OpenAIRE

    Andriušaitienė, Ramunė

    2007-01-01

    This Master thesis presents a study of computer equipment support services providing company’s business processes, specifics of the ongoing communication between end-users and supporting engineers-consultants and presents review of some information systems designed to automate certain technical support activities. Core aim of this study is to alleviate the daily work of above mentioned consultants when supporting end-users to locate and resolve issues in owned computer equipment. This paper o...

  10. Hydrogen Production Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Hydrogen Production Technical Team Roadmap identifies research pathways leading to hydrogen production technologies that produce near-zero net greenhouse gas (GHG) emissions from highly efficient and diverse renewable energy sources. This roadmap focuses on initial development of the technologies, identifies their gaps and barriers, and describes activities by various U.S. Department of Energy (DOE) offices to address the key issues and challenges.

  11. Technical specifications, Hanford production reactors

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, W.D. [comp.

    1962-06-25

    These technical specifications are applicable to the eight operating production reactor facilities, B, C, D, DR, F, H, KE, and KW. Covered are operating and performance restrictions and administrative procedures. Areas covered by the operating and performance restrictions are reactivity, reactor control and safety elements, power level, temperature and heat flux, reactor fuel loadings, reactor coolant systems, reactor confinement, test facilities, code compliance, and reactor scram set points. Administrative procedures include process control procedures, training programs, audits and inspections, and reports and records.

  12. Imperatives of intellectual capital and technical skills for innovation: Perspective on higher education

    Science.gov (United States)

    Alkhaffaf, Haetham H. Kasem; Aljanabi, AbdulQadir Rahomee Ahmed

    2016-08-01

    The purpose of this paper is to explore how intellectual capital and technical skills can affect innovation. This paper reviewed related literature with these concepts and then submits a proposed theoretical framework to manifest the relationship between these variable. This paper explores the intellectual capital and technical skills from higher education perspective as critical success factors for innovation and conclude show higher education institutions can benefit from the integration of intellectual capital and technical skills principles to develop innovation and achieve a high level of performance.

  13. Access to credit and determinants of technical inefficiency of specialized smallholder farmers in Chile

    Directory of Open Access Journals (Sweden)

    Stephan von Cramon-Taubadel

    2014-12-01

    Full Text Available Access to credit and credit constraint are critical determinants of competitiveness in agriculture; they have an impact on the technical efficiency of farms. The objective of this study was to analyze how credit variables influence the technical efficiency of two groups of specialized smallholder farmers in Chile. The translog stochastic production frontier model was used to predict the level of farm technical efficiency by the maximum likelihood method. Based on 2004 data, production functions and technical inefficiency score were estimated for 109 livestock and 342 crop producers. Results showed that the mean technical efficiency was 89% and 78% for crop and livestock producers, respectively. Technical efficiency increased with the decreasing use of inputs, dependence on on-farm income, farmer education, family size, and age of the head of household. Credit volume had a significant impact by increasing and decreasing efficiency in crop and livestock production, respectively. Correspondingly, credit-constrained farmers were less efficient in crop production and more efficient in livestock production. For livestock producers, credit volume and credit constraints were found to be endogenous to technical efficiency. A possible explanation is the organization of public support for small livestock producers in Chile, which provides lenders with information about individual livestock producers. Correcting for this endogeneity did not lead to qualitatively different results, but it did influence point estimates of parameters in the production function and inefficiency models, suggesting that it is important to test for endogeneity in the variables used to model inefficiency effects.

  14. Understanding Brown Dwarf Variability

    Science.gov (United States)

    Marley, Mark S.

    2013-01-01

    Surveys of brown dwarf variability continue to find that roughly half of all brown dwarfs are variable. While variability is observed amongst all types of brown dwarfs, amplitudes are typically greatest for L-T transition objects. In my talk I will discuss the possible physical mechanisms that are responsible for the observed variability. I will particularly focus on comparing and contrasting the effects of changes in atmospheric thermal profile and cloud opacity. The two different mechanisms will produce different variability signatures and I will discuss the extent to which the current datasets constrain both mechanisms. By combining constraints from studies of variability with existing spectral and photometric datasets we can begin to construct and test self-consistent models of brown dwarf atmospheres. These models not only aid in the interpretation of existing objects but also inform studies of directly imaged giant planets.

  15. Market Design Simulations with Variable Energy Resources (VERs) (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Ela, E.

    2011-06-01

    Presented at the FERC Technical Conference, 29 June 2011, Washington, D.C. This presentation describes NREL research regarding variable generation resources, operating reserves, unit commitment, economic dispatch, and introduces a new and novel modeling tool called 'FESTIV.'

  16. Why and How to Advance Technical Copywriting.

    Science.gov (United States)

    Henson, Leigh

    1996-01-01

    States that promotional writing for industrial/high-tech products, or technical copywriting, is gaining more attention in technical communication, although it is neglected in higher education. Testifies to the significance of technical copywriting. Suggests that dialogical audience analysis and an emphasis on rational appeal will contribute to…

  17. The Technical Problem and Its Didactic Function.

    Science.gov (United States)

    Jereb, Janez

    This paper deals with the different aspects of solving technical problems. To solve a technical problem in an optimal way it is not enough to consider the appropriate technical and technological principles, the different organizational, economical, and ergonomical principles must also be taken into account. The didactic aspects of solving…

  18. 7 CFR 3430.55 - Technical reporting.

    Science.gov (United States)

    2010-01-01

    ... required to submit other technical reports or submit the CRIS reports more frequently than annually... 7 Agriculture 15 2010-01-01 2010-01-01 false Technical reporting. 3430.55 Section 3430.55... ASSISTANCE PROGRAMS-GENERAL AWARD ADMINISTRATIVE PROVISIONS Post-Award and Closeout § 3430.55 Technical...

  19. Head Start Impact Study. Technical Report

    Science.gov (United States)

    Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

    2010-01-01

    This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

  20. TECHNICAL-VOCATIONAL EDUCATION IN VIETNAM.

    Science.gov (United States)

    Department of National Education, Saigon (South Vietnam).

    THE DIRECTORATE OF TECHNICAL EDUCATION, SET UP IN 1955, WAS GIVEN THE SPECIFIC DUTY OF TRAINING TECHNICIANS NEEDED FOR DEVELOPING INDUSTRY AND HANDICRAFTS. THE PROBLEMS OF TECHNICAL EDUCATION IN 1955 WERE--(1) THERE WERE ONLY TWO TECHNICAL SCHOOLS AND TWO APPRENTICE SCHOOLS, THREE APPLIED ARTS SCHOOLS, AND SEVEN ATELIER ECOLES (ARTISTS' OR…

  1. Technical specification improvement through safety margin considerations

    International Nuclear Information System (INIS)

    Howard, R.C.; Jansen, R.L.

    1986-01-01

    Westinghouse has developed an approach for utilizing safety analysis margin considerations to improve plant operability through technical specification revision. This approach relies on the identification and use of parameter interrelations and sensitivities to identify acceptable operating envelopes. This paper summarizes technical specification activities to date and presents the use of safety margin considerations as another viable method to obtain technical specification improvement

  2. Ultrasonic variables affecting inspection

    International Nuclear Information System (INIS)

    Lautzenheiser, C.E.; Whiting, A.R.; McElroy, J.T.

    1977-01-01

    There are many variables which affect the detection of the effects and reproducibility of results when utilizing ultrasonic techniques. The most important variable is the procedure, as this document specifies, to a great extent, the controls that are exercised over the other variables. The most important variable is personnel with regards to training, qualification, integrity, data recording, and data analysis. Although the data is very limited, these data indicate that, if the procedure is carefully controlled, reliability of defect detection and reproducibility of results are both approximately 90 percent for reliability of detection, this applies to relatively small defects as reliability increases substantially as defect size increases above the recording limit. (author)

  3. The nebular variables

    CERN Document Server

    Glasby, John S

    1974-01-01

    The Nebular Variables focuses on the nebular variables and their characteristics. Discussions are organized by type of nebular variable, namely, RW Aurigae stars, T Orionis stars, T Tauri stars, and peculiar nebular objects. Topics range from light variations of the stars to their spectroscopic and physical characteristics, spatial distribution, interaction with nebulosity, and evolutionary features. This volume is divided into four sections and consists of 25 chapters, the first of which provides general information on nebular variables, including their stellar associations and their classifi

  4. Legitimizing Technical Communication in English Departments: Carolyn Miller's "Humanistic Rationale for Technical Writing"

    Science.gov (United States)

    Moore, Patrick

    2006-01-01

    Carolyn Miller's oft-cited "Humanistic Rationale for Technical Writing," published in 1979, tries to give technical communication faculty more cultural capital in English departments controlled by literature professors. Miller replaces a positivistic emphasis in technical communication pedagogy with rhetoric. She shows how technical knowledge is…

  5. Software variability management

    NARCIS (Netherlands)

    Bosch, J; Nord, RL

    2004-01-01

    During recent years, the amount of variability that has to be supported by a software artefact is growing considerably and its management is evolving into a major challenge during development, usage, and evolution of software artefacts. Successful management of variability in software leads to

  6. Variability: A Pernicious Hypothesis.

    Science.gov (United States)

    Noddings, Nel

    1992-01-01

    The hypothesis of greater male variability in test results is discussed in its historical context, and reasons feminists have objected to the hypothesis are considered. The hypothesis acquires political importance if it is considered that variability results from biological, rather than cultural, differences. (SLD)

  7. Reinforcing Saccadic Amplitude Variability

    Science.gov (United States)

    Paeye, Celine; Madelain, Laurent

    2011-01-01

    Saccadic endpoint variability is often viewed as the outcome of neural noise occurring during sensorimotor processing. However, part of this variability might result from operant learning. We tested this hypothesis by reinforcing dispersions of saccadic amplitude distributions, while maintaining constant their medians. In a first experiment we…

  8. Interdependence Among Organizational Variables

    Science.gov (United States)

    Knowles, M. C.

    1975-01-01

    The interrelationship between a set of organizational variables was investigated at 14 work organizations within a company. The variables were production, quality, costs, job satisfaction of operatives, job satisfaction of supervisors, work anxiety, accidents, absence, labor turnover, and industrial unrest. (Author)

  9. Collective variables and dissipation

    International Nuclear Information System (INIS)

    Balian, R.

    1984-09-01

    This is an introduction to some basic concepts of non-equilibrium statistical mechanics. We emphasize in particular the relevant entropy relative to a given set of collective variables, the meaning of the projection method in the Liouville space, its use to establish the generalized transport equations for these variables, and the interpretation of dissipation in the framework of information theory

  10. Variable volume combustor

    Science.gov (United States)

    Ostebee, Heath Michael; Ziminsky, Willy Steve; Johnson, Thomas Edward; Keener, Christopher Paul

    2017-01-17

    The present application provides a variable volume combustor for use with a gas turbine engine. The variable volume combustor may include a liner, a number of micro-mixer fuel nozzles positioned within the liner, and a linear actuator so as to maneuver the micro-mixer fuel nozzles axially along the liner.

  11. Model to evaluate the technical efficiency of university units

    Directory of Open Access Journals (Sweden)

    Marlon Soliman

    2014-06-01

    Full Text Available In higher education institutions, the technical efficiency has been measured by several indicators that, when used separately, does not lead to an effective conclusion about the administrative reality of these. Therefore, this paper proposes a model to evaluate the technical efficiency of university units of a higher education institution (HEI from the perspectives of Teaching, Research and Extension. The conception of the model was performed according to the pressumptions of Data Envelopment Analysis (DEA, CCR model – product oriented, from the identification of relevant variables for the addressed context. The model was applied to evaluate the efficiency of nine academic units of the Federal University of Santa Maria (UFSM, obtaining as a result the efficiency of each unit as well as recommendations for the units considered inefficient. At the end of this study, it was verified that it is possible to measure the efficiency of various units and consequently establish goals for improvement based on the methodology used.

  12. Professional Excellence Beyond Technical Competence

    CERN Document Server

    Rossiter, Alan P

    2008-01-01

    The training path for engineers focuses intensely on scientific and technical knowledge. Yet, our professional and personal satisfaction and success also depend on other traits that make us more effective and productive. In this thought-provoking book, Alan Rossiter provides practical guidance in developing the skills to become more effective in your work, while also balancing your life. It is invaluable reading for graduating college students and young professionals as well as seasoned practitioners who find that work is becoming all-consuming.

  13. Technical presentation: Next Generation Oscilloscopes

    CERN Multimedia

    PH Department

    2011-01-01

      Rohde & Schwarz "Next Generation Oscilloscopes" - Introduction and Presentation Agenda: Wednesday 23 March  -  09:30 to 11:30 (open end) Bldg. 13-2-005 Language: English 09.30 Presentation "Next Generation Oscilloscopes" from Rohde & Schwarz RTO / RTM in theory and practice Gerard Walker 10.15 Technical design details from R&D Dr. Markus Freidhof 10.45 Scope and Probe Roadmap (confidential) Guido Schulze 11.00 Open Discussion Feedback, first impression, wishes, needs and requirements from CERN All 11.30 Expert Talks, Hands on All Mr. Dr. Markus Freidhof, Head of R&D Oscilloscopes, Rohde & Schwarz, Germany; Mr. Guido Schulze, ...

  14. Technical report on the accelerators

    International Nuclear Information System (INIS)

    Bex, L.

    1995-01-01

    GANIL operation and the technical studies performed in 1994 are described. The milestones for 1994 are: SISSI (Source d'Ions Secondaires a Supraconducteurs Intense) has been in operation and used for secondary beam production with four different primary beams. The 100 kV platform for beam injection in the CO1 has been in operation for production of metallic beams which demand is increasing. Finally the SPIRAL project (Systeme de Production d'Ions Radioactifs Acceleres en Ligne) is in progress. In late 1994 the civil work has started in view of the installation of the machine in the north part of the GANIL machine building. (K.A.)

  15. Fingerprinting of Materials: Technical Supplement

    Science.gov (United States)

    Workman, Gary L.

    1992-01-01

    This supplement to the Guidelines for Maintaining a Chemical Fingerprinting Program has been developed to assist NASA personnel, contractors, and sub-contractors in defining the technical aspects and basic concepts which can be used in chemical fingerprinting programs. This material is not meant to be totally inclusive to all chemical fingerprinting programs, but merely to present current concepts. Each program will be tailored to meet the needs of the individual organizations using chemical fingerprinting to improve their quality and reliability in the production of aerospace systems.

  16. Belle II Technical Design Report

    CERN Document Server

    Abe, T; Adamczyk, K; Ahn, S; Aihara, H; Akai, K; Aloi, M; Andricek, L; Aoki, K; Arai, Y; Arefiev, A; Arinstein, K; Arita, Y; Asner, D M; Aulchenko, V; Aushev, T; Aziz, T; Bakich, A M; Balagura, V; Ban, Y; Barberio, E; Barvich, T; Belous, K; Bergauer, T; Bhardwaj, V; Bhuyan, B; Blyth, S; Bondar, A; Bonvicini, G; Bozek, A; Bracko, M; Brodzicka, J; Brovchenko, O; Browder, T E; Cao, G; Chang, M -C; Chang, P; Chao, Y; Chekelian, V; Chen, A; Chen, K -F; Chen, P; Cheon, B G; Chiang, C -C; Chistov, R; Cho, K; Choi, S -K; Chung, K; Comerma, A; Cooney, M; Cowley, D E; Critchlow, T; Dalseno, J; Danilov, M; Dieguez, A; Dierlamm, A; Dillon, M; Dingfelder, J; Dolenec, R; Dolezal, Z; Drasal, Z; Drutskoy, A; Dungel, W; Dutta, D; Eidelman, S; Enomoto, A; Epifanov, D; Esen, S; Fast, J E; Feindt, M; Garcia, M Fernandez; Fifield, T; Fischer, P; Flanagan, J; Fourletov, S; Fourletova, J; Freixas, L; Frey, A; Friedl, M; Fruehwirth, R; Fujii, H; Fujikawa, M; Fukuma, Y; Funakoshi, Y; Furukawa, K; Fuster, J; Gabyshev, N; Cueto, A Gaspar de Valenzuela; Garmash, A; Garrido, L; Geisler, Ch; Gfall, I; Goh, Y M; Golob, B; Gorton, I; Grzymkowski, R; Guo, H; Ha, H; Haba, J; Hara, K; Hara, T; Haruyama, T; Hayasaka, K; Hayashi, K; Hayashii, H; Heck, M; Heindl, S; Heller, C; Hemperek, T; Higuchi, T; Horii, Y; Hou, W -S; Hsiung, Y B; Huang, C -H; Hwang, S; Hyun, H J; Igarashi, Y; Iglesias, C; Iida, Y; Iijima, T; Imamura, M; Inami, K; Irmler, C; Ishizuka, M; Itagaki, K; Itoh, R; Iwabuchi, M; Iwai, G; Iwai, M; Iwasaki, M; Iwasaki, M; Iwasaki, Y; Iwashita, T; Iwata, S; Jang, H; Ji, X; Jinno, T; Jones, M; Julius, T; Kageyama, T; Kah, D H; Kakuno, H; Kamitani, T; Kanazawa, K; Kapusta, P; Kataoka, S U; Katayama, N; Kawai, M; Kawai, Y; Kawasaki, T; Kennedy, J; Kichimi, H; Kikuchi, M; Kiesling, C; Kim, B K; Kim, G N; Kim, H J; Kim, H O; Kim, J -B; Kim, J H; Kim, M J; Kim, S K; Kim, K T; Kim, T Y; Kinoshita, K; Kishi, K; Kisielewski, B; van Dam, K Kleese; Knopf, J; Ko, B R; Koch, M; Kodys, P; Koffmane, C; Koga, Y; Kohriki, T; Koike, S; Koiso, H; Kondo, Y; Korpar, S; Kouzes, R T; Kreidl, Ch; Kreps, M; Krizan, P; Krokovny, P; Krueger, H; Kruth, A; Kuhn, W; Kuhr, T; Kumar, R; Kumita, T; Kupper, S; Kuzmin, A; Kvasnicka, P; Kwon, Y -J; Lacasta, C; Lange, J S; Lee, I -S; Lee, M J; Lee, M W; Lee, S -H; Lemarenko, M; Li, J; Li, W D; Li, Y; Libby, J; Limosani, A; Liu, C; Liu, H; Liu, Y; Liu, Z; Liventsev, D; Virto, A Lopez; Makida, Y; Mao, Z P; Marinas, C; Masuzawa, M; Matvienko, D; Mitaroff, W; Miyabayashi, K; Miyata, H; Miyazaki, Y; Miyoshi, T; Mizuk, R; Mohanty, G B; Mohapatra, D; Moll, A; Mori, T; Morita, A; Morita, Y; Moser, H -G; Martin, D Moya; Mueller, T; Muenchow, D; Murakami, J; Myung, S S; Nagamine, T; Nakamura, I; Nakamura, T T; Nakano, E; Nakano, H; Nakao, M; Nakazawa, H; Nam, S -H; Natkaniec, Z; Nedelkovska, E; Negishi, K; Neubauer, S; Ng, C; Ninkovic, J; Nishida, S; Nishimura, K; Novikov, E; Nozaki, T; Ogawa, S; Ohmi, K; Ohnishi, Y; Ohshima, T; Ohuchi, N; Oide, K; Olsen, S L; Ono, M; Ono, Y; Onuki, Y; Ostrowicz, W; Ozaki, H; Pakhlov, P; Pakhlova, G; Palka, H; Park, H; Park, H K; Peak, L S; Peng, T; Peric, I; Pernicka, M; Pestotnik, R; Petric, M; Piilonen, L E; Poluektov, A; Prim, M; Prothmann, K; Regimbal, K; Reisert, B; Richter, R H; Riera-Babures, J; Ritter, A; Ritter, A; Ritter, M; Roehrken, M; Rorie, J; Rosen, M; Rozanska, M; Ruckman, L; Rummel, S; Rusinov, V; Russell, R M; Ryu, S; Sahoo, H; Sakai, K; Sakai, Y; Santelj, L; Sasaki, T; Sato, N; Sato, Y; Scheirich, J; Schieck, J; Schwanda, C; Schwartz, A J; Schwenker, B; Seljak, A; Senyo, K; Seon, O -S; Sevior, M E; Shapkin, M; Shebalin, V; Shen, C P; Shibuya, H; Shiizuka, S; Shiu, J -G; Shwartz, B; Simon, F; Simonis, H J; Singh, J B; Sinha, R; Sitarz, M; Smerkol, P; Sokolov, A; Solovieva, E; Stanic, S; Staric, M; Stypula, J; Suetsugu, Y; Sugihara, S; Sugimura, T; Sumisawa, K; Sumiyoshi, T; Suzuki, K; Suzuki, S Y; Takagaki, H; Takasaki, F; Takeichi, H; Takubo, Y; Tanaka, M; Tanaka, S; Taniguchi, N; Tarkovsky, E; Tatishvili, G; Tawada, M; Taylor, G N; Teramoto, Y; Tikhomirov, I; Trabelsi, K; Tsuboyama, T; Tsunada, K; Tu, Y -C; Uchida, T; Uehara, S; Ueno, K; Uglov, T; Unno, Y; Uno, S; Urquijo, P; Ushiroda, Y; Usov, Y; Vahsen, S; Valentan, M; Vanhoefer, P; Varner, G; Varvell, K E; Vazquez, P; Vila, I; Vilella, E; Vinokurova, A; Visniakov, J; Vos, M; Wang, C H; Wang, J; Wang, M -Z; Wang, P; Wassatch, A; Watanabe, M; Watase, Y; Weiler, T; Wermes, N; Wescott, R E; White, E; Wicht, J; Widhalm, L; Williams, K M; Won, E; Xu, H; Yabsley, B D; Yamamoto, H; Yamaoka, H; Yamaoka, Y; Yamauchi, M; Yin, Y; Yoon, H; Yu, J; Yuan, C Z; Yusa, Y; Zander, D; Zdybal, M; Zhang, Z P; Zhao, J; Zhao, L; Zhao, Z; Zhilich, V; Zhou, P; Zhulanov, V; Zivko, T; Zupanc, A; Zyukova, O

    2010-01-01

    The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been proposed. A new international collaboration Belle-II, is being formed. The Technical Design Report presents physics motivation, basic methods of the accelerator upgrade, as well as key improvements of the detector.

  17. Technical approach to aging management

    International Nuclear Information System (INIS)

    Vora, J.P.; Johnson, A.B. Jr.; Allen, R.P.

    1992-10-01

    Systematic and effective control of age-related degradation of safety-related components, systems, and structures in nuclear power plants (NPPs) is an important challenge to plant operators. Several data bases, available to provide guidance on aging management, are summarized. However, the ultimate consideration is: How effectively is aging management being implemented at individual plants? Illustrated here is a specific strategy that served to develop the technical data base for the Nuclear Plant Aging Research Program. The strategy is comprehensive, systematic, and adaptable. Effective aging management at NPPs could be facilitated by a parallel strategy. The elements of a strategy are suggested

  18. Technical note on drainage systems

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    note is divided into four main topics: First, a short review of the precipitation in Denmark as well as how historical (actual) rainfall data can be used advantageously to those simple design methods, then how pipelines and reservoirs can be dimensioned and finally how safety in the design can......This technical note will present simple but widely used methods for the design of drainage systems. The note will primarily deal with surface water (rainwater) which on a satisfactorily way should be transport into the drainage system. Traditional two types of sewer systems exist: A combined system...

  19. CERN Technical Training: Signal Processor

    CERN Multimedia

    HR Department

    2009-01-01

    A new training is going to be held at CERN on the ADSP SHARC Family. The "System Development and Programming with the Analog Devices’ SHARC Family" course is a 3.5-day hands-on training on Analog Devices SHARC DSPs, focusing on the latest ‘368/9 and 37x families. General DSP architecture, peripherals available, booting up process and DSP code development will be covered. Hardware tools, debugging and hardware design guidelines will be introduced as well. The course id designed for System Designers needing to make informed decisions on design tradeoffs, Hardware Designers needing to develop external interfaces, and Code Developers needing to know how to get the highest performance from their algorithms. The course will take place, in English, from 31 March to 4 April in the CERN Technical Training Center. Few places are still available. Registrations are opened on the Technical Training page. More information on our catalogue: http://cta.cern.ch/cta2/f?p=110:9 or contact us with your que...

  20. Succession planning for technical experts

    Energy Technology Data Exchange (ETDEWEB)

    Kirk, Bernadette Lugue [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Cain, Ronald A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dewji, Shaheen A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Agreda, Carla L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-07-01

    This report describes a methodology for identifying, evaluating, and mitigating the loss of key technical skills at nuclear operations facilities. The methodology can be adapted for application within regulatory authorities and research and development organizations, and can be directly applied by international engagement partners of the Department of Energy’s National Nuclear Security Administration (NNSA). The resultant product will be of direct benefit to two types of NNSA missions: (1) domestic human capital development programs tasked to provide focused technical expertise to succeed an aging nuclear operations workforce, and (2) international safeguards programs charged with maintaining operational safeguards for developing/existing nuclear power program in nations where minimal available resources must be used effectively. This report considers succession planning and the critical skills necessary to meet an institution’s goals and mission. Closely tied to succession planning are knowledge management and mentorship. In considering succession planning, critical skill sets are identified and are greatly dependent on the subject matter expert in question. This report also provides examples of critical skills that are job specific.

  1. Technical approach to groundwater restoration

    International Nuclear Information System (INIS)

    1993-01-01

    The Technical Approach to Groundwater Restoration (TAGR) provides general technical guidance to implement the groundwater restoration phase of the Uranium Mill Tailings Remedial Action (UMTRA) Project. The TAGR includes a brief overview of the surface remediation and groundwater restoration phases of the UMTRA Project and describes the regulatory requirements, the National Environmental Policy Act (NEPA) process, and regulatory compliance. A section on program strategy discusses program optimization, the role of risk assessment, the observational approach, strategies for meeting groundwater cleanup standards, and remedial action decision-making. A section on data requirements for groundwater restoration evaluates the data quality objectives (DQO) and minimum data required to implement the options and comply with the standards. A section on sits implementation explores the development of a conceptual site model, approaches to site characterization, development of remedial action alternatives, selection of the groundwater restoration method, and remedial design and implementation in the context of site-specific documentation in the site observational work plan (SOWP) and the remedial action plan (RAP). Finally, the TAGR elaborates on groundwater monitoring necessary to evaluate compliance with the groundwater cleanup standards and protection of human health and the environment, and outlines licensing procedures

  2. Succession planning for technical experts

    International Nuclear Information System (INIS)

    Kirk, Bernadette Lugue; Cain, Ronald A.; Dewji, Shaheen A.; Agreda, Carla L.

    2017-01-01

    This report describes a methodology for identifying, evaluating, and mitigating the loss of key technical skills at nuclear operations facilities. The methodology can be adapted for application within regulatory authorities and research and development organizations, and can be directly applied by international engagement partners of the Department of Energy’s National Nuclear Security Administration (NNSA). The resultant product will be of direct benefit to two types of NNSA missions: (1) domestic human capital development programs tasked to provide focused technical expertise to succeed an aging nuclear operations workforce, and (2) international safeguards programs charged with maintaining operational safeguards for developing/existing nuclear power program in nations where minimal available resources must be used effectively. This report considers succession planning and the critical skills necessary to meet an institution’s goals and mission. Closely tied to succession planning are knowledge management and mentorship. In considering succession planning, critical skill sets are identified and are greatly dependent on the subject matter expert in question. This report also provides examples of critical skills that are job specific.

  3. Productivity Measurement Of Technical Institute

    Directory of Open Access Journals (Sweden)

    Miss.Pooja Yadav

    2015-05-01

    Full Text Available Abstract The increasing concern over globalization between other things has made the achievement of lifetime skills vital for all classes of people. Achievement of such skills can be developed from technical education programs in the advance of any nation. Skill gaining provides knowledge and inculcates the approaches that are essential for arrival and progress into an occupation. When skills are developed in any occupation it will provide and improve the standard of living with the cover beside poverty thereby behind national development. This paper observes sampling distribution and moving average concept that how technical education can generate the required skills the significance of skill acquisition its roles benefits and sustainability in national development. It also mentions among others that government should look into and improve productivity that can encourage skill achievement for the youths. The solutions are divided the sampling box into few group before stacking up workstation and use table and some other wood product. Cost reduction for each solution was intended and the solution with highest cost decrease is chosen to increase the productivity of the college.

  4. Technical Problems of Residential Construction

    Science.gov (United States)

    Nowogońska, Beata; Cibis, Jerzy

    2017-10-01

    Beauty, utility, durability - these are the features of good architecture and should also be the distinguishing qualities of every residential building. But do beauty and utility remain along with the passing of time? Performance characteristics are an indicator of both, the technical as well as aesthetic state of buildings. Aesthetic needs are in disagreement with the merciless aging process. The beauty of a city is formed not only by the original forms of new residential buildings, but also by existing tenement housing; thus preserving their aesthetics becomes a necessity. Time is continuously passing and along with it, aging intensifies. The aging process is a natural phenomenon for every material. The life expectancy of building materials is also limited. Along with the passing of time, the technical state of residential buildings continuously deteriorates. With the passing of time, the aesthetic values and preferences of users of flats change and the usability of the building decreases. The permanence of buildings, including residential buildings, is shaped not only by the forces of nature but also by activities of humans. A long lifespan is ensured by carrying out ongoing, systematic renovation-repair works. It is thanks to them that buildings derived from past centuries are still being used, and their market attractiveness is not decreasing.

  5. Technical aspects of MR perfusion

    International Nuclear Information System (INIS)

    Sourbron, Steven

    2010-01-01

    The most common methods for measuring perfusion with MRI are arterial spin labelling (ASL), dynamic susceptibility contrast (DSC-MRI), and T 1 -weighted dynamic contrast enhancement (DCE-MRI). This review focuses on the latter approach, which is by far the most common in the body and produces measures of capillary permeability as well. The aim is to present a concise but complete overview of the technical issues involved in DCE-MRI data acquisition and analysis. For details the reader is referred to the references. The presentation of the topic is essentially generic and focuses on technical aspects that are common to all DCE-MRI measurements. For organ-specific problems and illustrations, we refer to the other papers in this issue. In Section 1 'Theory' the basic quantities are defined, and the physical mechanisms are presented that provide a relation between the hemodynamic parameters and the DCE-MRI signal. Section 2 'Data acquisition' discusses the issues involved in the design of an optimal measurement protocol. Section 3 'Data analysis' summarizes the steps that need to be taken to determine the hemodynamic parameters from the measured data.

  6. The NASA Technical Report Server

    Science.gov (United States)

    Nelson, Michael L.; Gottlich, Gretchen L.; Bianco, David J.; Paulson, Sharon S.; Binkley, Robert L.; Kellogg, Yvonne D.; Beaumont, Chris J.; Schmunk, Robert B.; Kurtz, Michael J.; Accomazzi, Alberto

    1995-01-01

    The National Aeronautics and Space Act of 1958 established NASA and charged it to "provide for the widest practicable and appropriate dissemination of information concerning its activities and the results thereof." The search for innovative methods to distribute NASA's information lead a grass-roots team to create the NASA Technical Report Server (NTRS), which uses the World Wide Web and other popular Internet-based information systems as search engines. The NTRS is an inter-center effort which provides uniform access to various distributed publication servers residing on the Internet. Users have immediate desktop access to technical publications from NASA centers and institutes. The NTRS is comprised of several units, some constructed especially for inclusion in NTRS, and others that are existing NASA publication services that NTRS reuses. This paper presents the NTRS architecture, usage metrics, and the lessons learned while implementing and maintaining the service. The NTRS is largely constructed with freely available software running on existing hardware. NTRS builds upon existing hardware and software, and the resulting additional exposure for the body of literature contained ensures that NASA's institutional knowledge base will continue to receive the widest practicable and appropriate dissemination.

  7. Rapidly variable relatvistic absorption

    Science.gov (United States)

    Parker, M.; Pinto, C.; Fabian, A.; Lohfink, A.; Buisson, D.; Alston, W.; Jiang, J.

    2017-10-01

    I will present results from the 1.5Ms XMM-Newton observing campaign on the most X-ray variable AGN, IRAS 13224-3809. We find a series of nine absorption lines with a velocity of 0.24c from an ultra-fast outflow. For the first time, we are able to see extremely rapid variability of the UFO features, and can link this to the X-ray variability from the inner accretion disk. We find a clear flux dependence of the outflow features, suggesting that the wind is ionized by increasing X-ray emission.

  8. Technical Submission Form: Technical Specification of a Wave Energy Farm.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Jesse D.; Kim Nielsen; Ben Kennedy; Bull, Diana L; Costello, Ronan Patrick; Jochem Weber

    2017-04-01

    The Wave - SPARC project developed the Technology Performance Level (TPL) assessment procedure based on a rigorous Systems Engineering exercise. The TPL assessment allows a whole system evaluation of Wave Energy Conversion Technology by measuring it against the requirements determined through the Systems Engineering exercise. The TPL assessment is intended to be useful in technology evaluation; in technology innovation; in allocation of public or priva te investment, and; in making equipment purchasing decisions. This Technical Submission Form (TSF) serves the purpose of collecting relevant and complete information, in a technology agnostic way, to allow TPL assessment s to be made by third party assessor s. The intended usage of this document is that the organization or people that are performing the role of developers or promoters of a particular technology will use this form to provide the information necessary for the organization or people who are perf orming the assessor role to use the TPL assessment.

  9. Variable Heat Rejection (VHR)

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop advanced technologies to enable a variable heat rejection Thermal Control System (TCS) capable of operating through a wide range of thermal environments...

  10. Variable-Rate Premiums

    Data.gov (United States)

    Pension Benefit Guaranty Corporation — These interest rates are used to value vested benefits for variable rate premium purposes as described in PBGC's regulation on Premium Rates (29 CFR Part 4006) and...

  11. Variable Attitude Test Stand

    Data.gov (United States)

    Federal Laboratory Consortium — The Variable Attitude Test Stand designed and built for testing of the V-22 tilt rotor aircraft propulsion system, is used to evaluate the effect of aircraft flight...

  12. Classical pulsating variables

    International Nuclear Information System (INIS)

    Hacke, G.

    1987-01-01

    The nature of the three types of classical pulsating variables (δ-Cephei stars, W-Virginis stars and RR-Lyrae stars) is studied. Problems of the light-curve analysis such as (1) the frequency distribution of periods for the three types of classical pulsating variables, (2) spurions periods, (3) changes of periods and multiple periodicity as well as (4) the Blazhko-effect and other changes of the light-curve form are discussed

  13. Calculus of one variable

    CERN Document Server

    Grossman, Stanley I

    1986-01-01

    Calculus of One Variable, Second Edition presents the essential topics in the study of the techniques and theorems of calculus.The book provides a comprehensive introduction to calculus. It contains examples, exercises, the history and development of calculus, and various applications. Some of the topics discussed in the text include the concept of limits, one-variable theory, the derivatives of all six trigonometric functions, exponential and logarithmic functions, and infinite series.This textbook is intended for use by college students.

  14. Software Testing Requires Variability

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak

    2003-01-01

    Software variability is the ability of a software system or artefact to be changed, customized or configured for use in a particular context. Variability in software systems is important from a number of perspectives. Some perspectives rightly receive much attention due to their direct economic...... impact in software production. As is also apparent from the call for papers these perspectives focus on qualities such as reuse, adaptability, and maintainability....

  15. National climate assessment technical report on the impacts of climate and land use and land cover change

    Science.gov (United States)

    Thomas Loveland; Rezaul Mahmood; Toral Patel-Weynand; Krista Karstensen; Kari Beckendorf; Norman Bliss; Andrew Carleton

    2012-01-01

    This technical report responds to the recognition by the U.S. Global Change Research Program (USGCRP) and the National Climate Assessment (NCA) of the importance of understanding how land use and land cover (LULC) affects weather and climate variability and change and how that variability and change affects LULC. Current published, peer-reviewed, scientific literature...

  16. Research on Efficiency of Knowledge Transfer in Technical Innovation Alliances

    Science.gov (United States)

    Zhang-sheng, Jiang

    The knowledge transfer efficiency (KTE) is closely relative to the success or failure of technology innovation in strategic alliances. This paper takes the KTE as the essential variable to establish the benefit function model of technology innovations to explore the KTE's influences on partners' innovative decisions under two different modes: independent innovations and alliance innovations. It is found that the higher the KTE, the greater the reducing extent of production costs is. The results could provide some theoretical supports for selections of the optimal competitive-ooperative relationship and managerial flexibility in technical innovation alliances.

  17. How to be an Effective Technical Writer?

    Directory of Open Access Journals (Sweden)

    M Solaiman Ali

    2012-07-01

    Full Text Available Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations. Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical writing for engineers stresses that a successful engineering career requires strong writing skills. Part 2 (How to write the major sections or elements of a report describes the techniques of writing the abstract, introduction, literature review, procedure/methods & materials, results, discussion, conclusion, and recommendations. Part 3 (Special features of technical writing brings into focus some of the special features of technical writing such as tables & graphs in the text, graphics in instructions, team writing, ethics (plagiarism, document sources, three citation styles and IEEE reference style. Part 4 (Technical usage deals with writing abbreviations, initialisms and acronyms, numbers, units of measurement, and equations.Part 5 (Technical style highlights the imperative writing style and other features of technical writing such as the use of active and passive voices, plain vs. complex syntax, avoiding redundant or superfluous expressions, and vague generalities, using words or expressions with visual impact, the past tense to describe experimental work, the present tense to describe hypotheses, principles, theories and truths, and breaking up the text of the report into short sections. Part 6 (Document specifications emphasizes the technical writer’s need to conform to such document specifications as word count, format, font, number of words per line of text imposed. Part 7 (Reader-friendly technical writing suggests choosing the varied writing modes

  18. Marketing information: The technical report as product

    Science.gov (United States)

    Stoher, F. F.; Pinelli, T. E.

    1981-01-01

    Technical reports constitute a product, the primary means for communicating the results of research to the user. The Langley scientific and technical information (STI) review and evaluation project undertook a review of the technical report as an effective product for information communication. Style manuals describing theory and practice in technical report preparation; publication manuals covering such factors as design, layout, and type style; and copies of technical reports were obtained from industrial, academic, governmental, and research organizations. Based on an analysis of this material, criteria will be established for the report components, for the relationship of the components within the report context, and for the overall report organization. The criteria will be used as bench marks and compared with the publication standards currently used to prepare NASA technical reports.

  19. Technical risks as a constitutional problem

    International Nuclear Information System (INIS)

    Murswiek, D.

    1991-01-01

    Between the constitutional duty to protect, and the limits of protecting powers lies a domain where governmental bodies are empowered, but not obligated, to control and plan technical development and risks. Thus there is political responsibility for the way technical matters are handled, and a constitutional perspetive for accepting technical risks. As long as there has been general consent for technical progress, politicians were able to let the progress process take its course. Now they are asked to intervene. The transformation of living conditions through technical innovation has a greater significance for the individual and the State as a whole than most of the other matters of political decision-making. It would be irresponsible therefore to leave technical development to its own dynamics, and not continuously assess impacts of new technologies, weight up possible advantages and disadvantages, and change the course if necessary. (orig./HWCH) [de

  20. Superphenix: technical and scientific achievements

    International Nuclear Information System (INIS)

    Guidez, Joel; Prele, Gerard

    2016-04-01

    In this book, the authors propose a synthesis of technical and scientific achievements related to the design, fabrication and eleven-year operation of Superphenix, the most powerful fast breeder reactor ever built and operated. They had the opportunity to use various and important archives maintained by the different involved institutions, actors and companies, such as the CEA with its MADONA database, AREVA and EDF. They address all the different fields: construction, chemistry, exploitation, handling, small and large components, materials, fuel manufacturing, environmental assessment, thermal hydraulics, the sodium-water reaction, sodium fires, the release of residual power, in-service inspection, and dismantling operations. Moreover, a chapter addresses design studies for Superphenix 2 and for the European Fast Reactor (EFR) which should be the successors of Superphenix

  1. The Socio-Technical Man

    Science.gov (United States)

    Moreno, Yamir

    In the last 20 years or so, the field of complexity science has entered a new age. The combination of new theoretical insights and the data revolution has prepared the ground for a number of conceptual milestones in many disciplines as diverse as biology, physics, engineering, and economic and social sciences. At the same time, we have been able to identify new challenges whose solutions will confer the science of complex systems an unprecedented applied dimension. Here I would like to focus on one of these challenges: the socio-technical man. With the ever-increasing growth of both the world population and new technologies, it is fundamental for the well-being of humanity and our society to understand how humans interact among them and with the new technological environment...

  2. Chernobyl - a Canadian technical perspective

    International Nuclear Information System (INIS)

    Howieson, J.Q.; Snell, V.G.

    1987-01-01

    In this report we present the design review done to date in Canada by AECL. From the Canadian point of view it covers: 1) relevant information on the Chernobyl design and the accident, both as presented by the Soviets at the Post-Accident Review Meeting (PARM) held in Vienna from August 25-29, 1986, and as deduced from publicly available Soviet documentation; and 2) details of AECL's technical review of the CANDU PHWR (Pressurized Heavy Water Reactor) against the background of the Chernobyl accident, and implications of the Chernobyl accident. Reviews of operational aspects are underway by the Canadian electrical utilities and a review by the Canadian regulatory agency (the Atomic Energy Control Board) is near completion

  3. The International Technical Safety Forum

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    The International Technical Safety Forum is a meeting of safety experts from several physics labs in Europe and the US. Since 1998 participants have been meeting every couple of years to discuss common challenges in safety matters. The Forum helps them define best practices and learn from the important lessons learned by others.   The Forum's participants in front of building 40. This year, the meeting took place at CERN from 12 to 16 April. “This year's meeting covered subjects ranging from communication and training in matters of safety, to cryogenic safety, emergency preparedness and risk analysis”, explains Ralf Trant, head of the CERN Safety Commission and organiser of this year’s Forum. Radiation protection issues are not discussed at the meeting since they involve different expertise. The goal of the Forum is to allow participants to share experience, learn lessons and acquire specific knowledge in a very open way. Round-table discussions, dedicated time for ...

  4. Technical abstracts: Mechanical engineering, 1990

    International Nuclear Information System (INIS)

    Broesius, J.Y.

    1991-01-01

    This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing

  5. Crew Transportation Technical Management Processes

    Science.gov (United States)

    Mckinnie, John M. (Compiler); Lueders, Kathryn L. (Compiler)

    2013-01-01

    Under the guidance of processes provided by Crew Transportation Plan (CCT-PLN-1100), this document, with its sister documents, International Space Station (ISS) Crew Transportation and Services Requirements Document (CCT-REQ-1130), Crew Transportation Technical Standards and Design Evaluation Criteria (CCT-STD-1140), Crew Transportation Operations Standards (CCT STD-1150), and ISS to Commercial Orbital Transportation Services Interface Requirements Document (SSP 50808), provides the basis for a National Aeronautics and Space Administration (NASA) certification for services to the ISS for the Commercial Provider. When NASA Crew Transportation System (CTS) certification is achieved for ISS transportation, the Commercial Provider will be eligible to provide services to and from the ISS during the services phase.

  6. Technical abstracts: Mechanical engineering, 1990

    Energy Technology Data Exchange (ETDEWEB)

    Broesius, J.Y. (comp.)

    1991-03-01

    This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing.

  7. MELCOR technical assessment at SNL

    International Nuclear Information System (INIS)

    Kmetyk, L.N.; Tautges, T.J.

    1993-01-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor (LWR) nuclear power plants, which is being developed at Sandia National Laboratories for the US Nuclear Regulatory Commission (US-NRC). The entire spectrum of severe accident phenomena, including reactor coolant system and containment thermal/hydraulic response, core heatup, degradation and relocation, and fission product release and transport, is treated in MELCOR in a unified framework for both boiling water reactors (PRWs). The MELCOR computer code has been developed to the point that is now being successfully applied in severe accident analyses, particularly in probabilistic risk assessment (PRA) studies. MELCOR was the first of the severe accident analysis code to undergo a formal peer review process. One of the major conclusions of the recent MELCOR Peer Review was the need for a more comprehensive and more systematic program of MELCOR assessment. This report provides a discussion of this technical assessment

  8. The Migration of Technical Workers

    DEFF Research Database (Denmark)

    Dahl, Michael S.; Sorenson, Olav

    2010-01-01

    Using panel data on the Danish population, we estimated the revealed preferences of scientists and engineers for the places in which they choose to work. Our results indicate that these technical workers exhibit substantial sensitivity to differences in wages but that they have even stronger...... preferences for living close to family and friends. The magnitude of these preferences, moreover, suggests that the greater geographic mobility of scientists and engineers, relative to the population as a whole, stems from more pronounced variation across regions in the wages that they can expect....... These results remain robust to estimation on a sample of individuals who must select new places of work for reasons unrelated to their preferences—those who had been employed at establishments that discontinued operations....

  9. Chaotic Phenomena in Technical Control Systems

    DEFF Research Database (Denmark)

    Mosekilde, Erik

    1997-01-01

    The paper discusses a number of examples of technical control systems that can exhibit deterministic chaos and other forms of complex nonlinear behavior. These examples include thermostatically regulated radiators, closely placed refrigirators, and industrial cooling compressors. The paper...... continues to describe the possible perspective in driving our technical systems to operate in a chaotic regime. An example of a technical system capable of operating under unstable conditions is the F/A-18 fighter....

  10. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B1: Education. Technical Report 49B1

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2009

    2009-01-01

    This technical paper contains information about the variables in the LSAY (Longitudinal Surveys of Australian Youth) Y95 cohort data set. It groups each variable into data elements which identifies common variables within and across waves. Information is provided about each data element including its purpose, values, base populations and relevant.…

  11. Longitudinal Surveys of Australian Youth (LSAY): 1995 Cohort--User Guide. Data Elements B2: Education. Technical Report 49B2

    Science.gov (United States)

    National Centre for Vocational Education Research (NCVER), 2009

    2009-01-01

    This technical paper contains information about the variables in the Longitudinal Surveys of Australian Youth (LSAY) Year 95 cohort data set. It groups each variable into data elements that identify common variables within and across waves. Information is provided about each data element, including its purpose, values, base populations and…

  12. Judicial action and technical risk

    International Nuclear Information System (INIS)

    Buiren, S. van; Ballerstedt, E.; Grimm, D.

    1981-05-01

    In this study it is examined how the judiciary deals with those sections that are crucial for the use of nuclear energy. The authors get down to the pre-dominant problem of the law relating to technical safety. In the process they encounter the central dilemma of modern democracy, i.e. the strained relations which exist between judicial control and democratic responsibility. Since nuclear energy entered the market place, it has been the administrative courts which - in practice - have decided whether and to what extent nuclear energy may be used. On the one hand, this is a result of the fast growth of, and rapid change in, science and technology. On the other hand, it is a result of administrative law standards which have developed in the Federal Republic of Germany after World War II. The former requires the normative structure of the atomic law, the latter postulates how to deal with it. Legal protection against an act of public authority is guaranteed by the Basic Law and usually with some justification considered a splendid achievement of our state which is based on the rule of law. It has lead to developments in the atomic law and in many parts of the law relating to technical safety on which opinions are divided. In a dogmatic manner it has been legally examined to what extent an extensive review competence of the judiciary is a must, and whether there are any possibilities of judicial control of acts of public authorities without having to interfere with the original competence of administrations. (orig./HP) [de

  13. Conjoint utility analysis of technical maturity and project progress of construction project

    Directory of Open Access Journals (Sweden)

    Ma Wei

    2016-01-01

    Full Text Available In this paper, taking construction project as the research object, the relationship between the project maturity index calculated by the construction project technical risks with different fine degree and the project progress index is studied, and the equilibrium relationship between the Party A’s utility curve and the Party B’s cost curve of using project maturity index and project progress index as the research variables is analyzed. The results show that, when the construction project technical risk division is more precise, the conjoint utility of the project's technical maturity index and the project progress is higher, and the project’s Party A and Party B two sides are closer to the optimal equilibrium. This shows that the construction project technical risk must be finely divided, and managed and controlled respectively, which will help to improve the conjoint utility of the project Party A and Party B two sides.

  14. Technical Project Planning (TPP) Process. Engineer Manual

    National Research Council Canada - National Science Library

    1998-01-01

    This Engineer Manual (EM) describes the Technical Project Planning (TPP) process for identifying project objectives and designing data collection programs at hazardous, toxic, and radioactive waste sites...

  15. Technical Excellence: A Requirement for Good Engineering

    Science.gov (United States)

    Gill, Paul S.; Vaughan, William W.

    2008-01-01

    Technical excellence is a requirement for good engineering. Technical excellence has many different ways of expressing itself within engineering. NASA has initiatives that address the enhancement of the Agency's technical excellence and thrust to maintain the associated high level of performance by the Agency on current programs/projects and as it moves into the Constellation Program and the return to the Moon with plans to visit Mars. This paper addresses some of the key initiatives associated with NASA's technical excellence thrust. Examples are provided to illustrate some results being achieved and plans to enhance these initiatives.

  16. Technical Support for Contaminated Sites | Science Inventory ...

    Science.gov (United States)

    In 1987, the U.S. Environmental Protection Agency’s (EPA) Office of Research and Development (ORD), Office of Land and Emergency Management, and EPA Regional waste management offices established the Technical Support Project. The creation of the Technical Support Project enabled ORD to provide effective technical assistance by ensuring ORD scientists and engineers were accessible to the Agency’s Office and Regional decision makers, including Remedial Project Managers, On-Scene Coordinators, and corrective action staff. Five ORD Technical Support Centers (TSCs) were created to facilitate this technical assistance. Three of the five TSCs are supported by the Sustainable and Healthy Communities Research Program, and are summarized in the poster being presented:• Engineering Technical Support Center (ETSC) in Cincinnati, Ohio• Ground Water Technical Support Center (GWTSC) in Ada, Oklahoma• Site Characterization and Monitoring Technical Support Center (SCMTSC) in Atlanta, GeorgiaOver the past 29 years, the Technical Support Centers have provided numerous influential products to its internal Agency clients and to those at the State level (through the EPA Regions). These products include, but are not limited to the following: Annual TSC reports from the three Centers, a hard-rock mining conference every other year, PRO-UCL software development for site characterization statistics, groundwater modeling using state-of-the-art modeling software, numerical mo

  17. Improved technical specifications for Korean NPP

    International Nuclear Information System (INIS)

    Ryu, J. D.; Lee, D. H.; Seong, C. K.

    2002-01-01

    PWRs use Technical Specifications(Tech. Spec.) to ensure safe operation of the plant. Recently, many efforts were made to improve Tech. Spec. and as a result, Improved Standard Technical Specifications(ISTS) have been developed. Korean NPP technical specifications were converted to ISTS format. KAERI also provided supporting documents for technical specification conversion including mark-up's and description of changes. This paper describes and summarizes the results of implementation of ISTS for Korean NPP. The new Tech. Spec. will improve safety of Korean NPP

  18. The Evolution of Power System Planning with High Levels of Variable Renewable Generation

    Energy Technology Data Exchange (ETDEWEB)

    Katz, Jessica [National Renewable Energy Lab. (NREL), Golden, CO (United States); Milligan, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-09-01

    Greening the Grid provides technical assistance to energy system planners, regulators, and grid operators to overcome challenges associated with integrating variable renewable energy into the grid. This document, part of the Greening the Grid introduces the evolution of power system planning with high levels of variable renewable generation.

  19. Latent vs. Observed Variables : Analysis of Irrigation Water Efficiency Using SEM and SUR

    NARCIS (Netherlands)

    Tang, Jianjun; Folmer, Henk

    In this paper we compare conceptualising single factor technical and allocative efficiency as indicators of a single latent variable, or as separate observed variables. In the former case, the impacts on both efficiency types are analysed by means of structural equationmodeling (SEM), in the latter

  20. ANALYZING THE TECHNICAL EFFICIENCY OF RICE FARMS IN THE RIO GRANDE DO SUL

    Directory of Open Access Journals (Sweden)

    Augusto Mussi Alvim

    2015-03-01

    Full Text Available This paper evaluates the technical efficiency in rice farms in Rio Grande do Sul (RS. For this, we use the Data Envelopment Analysis (DEA and the Tobit regression model. The study use the variables available in the Census of the Institute of Irrigated Rice of RS (IRGA, 2006. The study shows that most of the rice farmers are technically inefficient on local terms, and only 5.7% are efficient. In addition, it is possible to observe that the main variables, which increase the level of efficiency in different regions of the state, are technical assistance, education level and growing system. The results show that there are important differences between the rice farms, which depends of the region of RS and of the producer condition (owner or tenant.

  1. [Analysis of the technical efficiency of hospitals in the Spanish National Health Service].

    Science.gov (United States)

    Pérez-Romero, Carmen; Ortega-Díaz, M Isabel; Ocaña-Riola, Ricardo; Martín-Martín, José Jesús

    To analyse the technical efficiency and productivity of general hospitals in the Spanish National Health Service (NHS) (2010-2012) and identify explanatory hospital and regional variables. 230 NHS hospitals were analysed by data envelopment analysis for overall, technical and scale efficiency, and Malmquist index. The robustness of the analysis is contrasted with alternative input-output models. A fixed effects multilevel cross-sectional linear model was used to analyse the explanatory efficiency variables. The average rate of overall technical efficiency (OTE) was 0.736 in 2012; there was considerable variability by region. Malmquist index (2010-2012) is 1.013. A 23% variability in OTE is attributable to the region in question. Statistically significant exogenous variables (residents per 100 physicians, aging index, average annual income per household, essential public service expenditure and public health expenditure per capita) explain 42% of the OTE variability between hospitals and 64% between regions. The number of residents showed a statistically significant relationship. As regards regions, there is a statistically significant direct linear association between OTE and annual income per capita and essential public service expenditure, and an indirect association with the aging index and annual public health expenditure per capita. The significant room for improvement in the efficiency of hospitals is conditioned by region-specific characteristics, specifically aging, wealth and the public expenditure policies of each one. Copyright © 2016 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

  2. Study on the Technical Efficiency of Creative Human Capital in China by Three-Stage Data Envelopment Analysis Model

    Directory of Open Access Journals (Sweden)

    Jian Ma

    2014-01-01

    Full Text Available Previous researches have proved the positive effect of creative human capital and its development on the development of economy. Yet, the technical efficiency of creative human capital and its effects are still under research. The authors are trying to estimate the technical efficiency value in Chinese context, which is adjusted by the environmental variables and statistical noises, by establishing a three-stage data envelopment analysis model, using data from 2003 to 2010. The research results indicate that, in this period, the entirety of creative human capital in China and the technical efficiency value in different regions and different provinces is still in the low level and could be promoted. Otherwise, technical non-efficiency is mostly derived from the scale nonefficiency and rarely affected by pure technical efficiency. The research also examines environmental variables’ marked effects on the technical efficiency, and it shows that different environmental variables differ in the aspect of their own effects. The expansion of the scale of education, development of healthy environment, growth of GDP, development of skill training, and population migration could reduce the input of creative human capital and promote the technical efficiency, while development of trade and institutional change, on the contrary, would block the input of creative human capital and the promotion the technical efficiency.

  3. Neuroanatomical variability of religiosity.

    Science.gov (United States)

    Kapogiannis, Dimitrios; Barbey, Aron K; Su, Michael; Krueger, Frank; Grafman, Jordan

    2009-09-28

    We hypothesized that religiosity, a set of traits variably expressed in the population, is modulated by neuroanatomical variability. We tested this idea by determining whether aspects of religiosity were predicted by variability in regional cortical volume. We performed structural magnetic resonance imaging of the brain in 40 healthy adult participants who reported different degrees and patterns of religiosity on a survey. We identified four Principal Components of religiosity by Factor Analysis of the survey items and associated them with regional cortical volumes measured by voxel-based morphometry. Experiencing an intimate relationship with God and engaging in religious behavior was associated with increased volume of R middle temporal cortex, BA 21. Experiencing fear of God was associated with decreased volume of L precuneus and L orbitofrontal cortex BA 11. A cluster of traits related with pragmatism and doubting God's existence was associated with increased volume of the R precuneus. Variability in religiosity of upbringing was not associated with variability in cortical volume of any region. Therefore, key aspects of religiosity are associated with cortical volume differences. This conclusion complements our prior functional neuroimaging findings in elucidating the proximate causes of religion in the brain.

  4. Predisposition Factors of Career and Technical Education Transfer Students: A Hermeneutic Phenomenology Study

    Science.gov (United States)

    Hioki, Warren; Lester, Derek; Martinez, Mario

    2015-01-01

    Six college students, who were career and technical education (CTE) transfer students in the state of Nevada, were interviewed Spring Semester of 2009. The study used a hermeneutic phenomenology framework as the method to identify those predisposition variables that heavily influenced the students in their decision to transfer to a senior…

  5. Direct Instruction and First Grade Reading Achievement: The Role of Technical Support and Time of Implementation

    Science.gov (United States)

    Stockard, Jean

    2011-01-01

    The purpose of this study was to examine the relationship of two implementation variables (source of technical support and time of implementation) to first grade reading achievement across three naturally-occurring conditions over a six-year time span. Two of the conditions involved implementation of Direct Instruction (DI) curriculum programs,…

  6. The Economic Value of Fundamental and Technical Information in Emerging Currency Markets

    NARCIS (Netherlands)

    G.J. de Zwart (Gerben); T.D. Markwat (Thijs); L.A.P. Swinkels (Laurens); D.J.C. van Dijk (Dick)

    2007-01-01

    textabstractWe measure the economic value of information derived from macroeconomic variables and from technical trading rules for emerging markets currency investments. Our analysis is based on a sample of 21 emerging markets with a floating exchange rate regime over the period 1997-2007 and

  7. Technical Efficiency Estimation via Metafrontier Technique with Factors that Affect Supply Chain Operations

    OpenAIRE

    Ibrahim Mosaad El-Atroush; Gabriel Montes-Rojas

    2011-01-01

    This paper presents a metafrontier production function and investigates factors that affect textile and apparel supply chain operations for firms operating under different technologies and ownership structures. Results show variability in efficiency scores. In addition, we find supply chain operations shift the production function and enhance technical efficiency.

  8. Multiple Intelligence Distribution of Prospective Teachers: The Case at Yildiz Technical University

    Science.gov (United States)

    Çeliköz, Mine

    2017-01-01

    The aim of this study is to find out whether intelligence distributions differ or not according to gender and departmental variables by determining the dominant intelligence (Multiple Intelligence) distributions of prospective teachers studying at Yildiz Technical University Education Faculty. The population of the research constitutes the…

  9. Catastrophic failure in complex socio-technical systems

    Energy Technology Data Exchange (ETDEWEB)

    Weir, D. [Intercultural Management, Rue Dostoievski, BP 085, 06902 Sophia Antipolis (France)]. E-mail: dweir@tinyworld.co.uk

    2004-07-01

    This paper reviews the sequences leading to catastrophic failures in complex socio-technical systems. It traces some of the elements of an analytic framework to that proposed by Beer in Decision and Control, first published in 1966, and argues that these ideas are centrally relevant to a topic on which research interest has developed subsequently, the study of crises, catastrophes and disasters in complex socio-technical systems in high technology sectors. But while the system perspective is central, it is not by itself entirely adequate. The problems discussed cannot be discussed simply in terms of system parameters like variety, redundancy and complexity. Much empirical research supports the view that these systems typically operate in degraded mode. The degradations may be primarily initiated within the social components of the socio-technical system. Such variables as hierarchical position, actors' motivations and intentions are relevant to explain the ways in which communication systems typically operate to filter out messages from lower participants and to ignore the 'soft signals' issuing from small-scale and intermittent malfunctions. (author)

  10. Technical and Physical Activities of Small-Sided Games in Young Korean Soccer Players.

    Science.gov (United States)

    Joo, Chang H; Hwang-Bo, Kwan; Jee, Haemi

    2016-08-01

    Joo, CH, Hwang-Bo, K, and Jee, H. Technical and physical activities of small-sided games in young Korean soccer players. J Strength Cond Res 30(8): 2164-2173, 2016-The aim of this study was to examine the technical aspects and physical demands during small-sided games (SSGs) with different sized pitches in young Korean soccer players. Participants were randomly selected during a nationally held youth competition. Three different game formats were used: SSG8 (8 vs. 8 played on a small-sized field [68 × 47 m]), RSG8 (8 vs. 8 played on a regular-sized field [75 × 47 m]), and RSG11 (11 vs. 11 played on a regular-sized field). Eleven technical (ball touches, passes, and shots) and 6 physical demand variables (exercise frequency by intensity) were observed and analyzed. Same variables were also analyzed for the goalkeepers. As a result, SSG8 and RSG8 showed significantly greater numbers of technical plays in 5 and 4 variables in comparison to RSG11, respectively. In addition, although the exercise intensities increased slightly in both SSG formats, the amount was within the similar range as previous reports. In conclusion, the SSGs with reduced number of players may be referred in young players to effectively train them in technical aspects of the game by allowing greater ball exposure time without excessive physical demands. Various confounding factors such as pitch dimension should be carefully considered for training specific technical and physical variables in young Korean players.

  11. 76 FR 29333 - Pipeline Safety: Meetings of the Technical Pipeline Safety Standards Committee and the Technical...

    Science.gov (United States)

    2011-05-20

    ... pipeline rehabilitation, replacement and repair initiatives along with all forum-related comments. PHMSA... Pipeline and Hazardous Materials Safety Administration Pipeline Safety: Meetings of the Technical Pipeline Safety Standards Committee and the Technical Hazardous Liquid Pipeline Safety Standards Committee AGENCY...

  12. Pulsating red variables

    International Nuclear Information System (INIS)

    Whitelock, P.A.

    1990-01-01

    The observational characteristics of pulsating red variables are reviewed with particular emphasis on the Miras. These variables represent the last stage in the evolution of stars on the Asymptotic Giant Branch (AGB). A large fraction of the IRAS sources in the Bulge are Mira variables and a subset of these are also OH/IR sources. Their periods range up to 720 days, though most are between 360 and 560 days. At a given period those stars with the highest pulsation amplitudes have the highest mass-loss rates; this is interpreted as evidence for a causal connection between mass-loss and pulsation. It is suggested that once an AGB star has become a Mira it will evolve with increasing pulsation amplitude and mass-loss, but with very little change of luminosity or logarithmic period. 26 refs

  13. Internal variables in thermoelasticity

    CERN Document Server

    Berezovski, Arkadi

    2017-01-01

    This book describes an effective method for modeling advanced materials like polymers, composite materials and biomaterials, which are, as a rule, inhomogeneous. The thermoelastic theory with internal variables presented here provides a general framework for predicting a material’s reaction to external loading. The basic physical principles provide the primary theoretical information, including the evolution equations of the internal variables. The cornerstones of this framework are the material representation of continuum mechanics, a weak nonlocality, a non-zero extra entropy flux, and a consecutive employment of the dissipation inequality. Examples of thermoelastic phenomena are provided, accompanied by detailed procedures demonstrating how to simulate them.

  14. Resiliencia y variables sociodemograficas

    OpenAIRE

    Calero Martinez, Edgar David

    2015-01-01

    En el presente trabajo se aborda la definición de una de las variables dentro de lo que se denomina Capital psicológico positivo, la Resiliencia, sus principales características y algunas de las variables socio demográficas que en el estudio pretenden ver el nivel de relación existente entre cada una de ellas (indirecta o directamente) en el proceso resiliente de una persona para posteriores discusiones y su implicación dentro de la gestión empresarial y sus direcciones futuras.

  15. Complex variables I essentials

    CERN Document Server

    Solomon, Alan D

    2013-01-01

    REA's Essentials provide quick and easy access to critical information in a variety of different fields, ranging from the most basic to the most advanced. As its name implies, these concise, comprehensive study guides summarize the essentials of the field covered. Essentials are helpful when preparing for exams, doing homework and will remain a lasting reference source for students, teachers, and professionals. Complex Variables I includes functions of a complex variable, elementary complex functions, integrals of complex functions in the complex plane, sequences and series, and poles and r

  16. Terrestrial Carbon Cycle Variability.

    Science.gov (United States)

    Baldocchi, Dennis; Ryu, Youngryel; Keenan, Trevor

    2016-01-01

    A growing literature is reporting on how the terrestrial carbon cycle is experiencing year-to-year variability because of climate anomalies and trends caused by global change. As CO 2 concentration records in the atmosphere exceed 50 years and as satellite records reach over 30 years in length, we are becoming better able to address carbon cycle variability and trends. Here we review how variable the carbon cycle is, how large the trends in its gross and net fluxes are, and how well the signal can be separated from noise. We explore mechanisms that explain year-to-year variability and trends by deconstructing the global carbon budget. The CO 2 concentration record is detecting a significant increase in the seasonal amplitude between 1958 and now. Inferential methods provide a variety of explanations for this result, but a conclusive attribution remains elusive. Scientists have reported that this trend is a consequence of the greening of the biosphere, stronger northern latitude photosynthesis, more photosynthesis by semi-arid ecosystems, agriculture and the green revolution, tropical temperature anomalies, or increased winter respiration. At the global scale, variability in the terrestrial carbon cycle can be due to changes in constituent fluxes, gross primary productivity, plant respiration and heterotrophic (microbial) respiration, and losses due to fire, land use change, soil erosion, or harvesting. It remains controversial whether or not there is a significant trend in global primary productivity (due to rising CO 2 , temperature, nitrogen deposition, changing land use, and preponderance of wet and dry regions). The degree to which year-to-year variability in temperature and precipitation anomalies affect global primary productivity also remains uncertain. For perspective, interannual variability in global gross primary productivity is relatively small (on the order of 2 Pg-C y -1 ) with respect to a large and uncertain background (123 +/- 4 Pg-C y -1 ), and

  17. Factors Affecting Women Enrolment In Technical Institutions In Tanzania A Case Study Of Arusha Technical College

    OpenAIRE

    Glory B. Kaaya; Dr. Esther Waiganjo

    2015-01-01

    Abstract The purpose of this study was to investigate the factors affecting women enrolment in Technical Institutions in Tanzania by focusing on the women. The study examined in detail the factors affecting women enrolment in Technical institutions and Arusha Technical College in particular as well as exploring sexual dynamics within Technical Institutions. Moreover a number of theoretical frameworks were concerned basing on the objectives a case study design was employed involving both qua...

  18. Biological Sampling Variability Study

    Energy Technology Data Exchange (ETDEWEB)

    Amidan, Brett G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hutchison, Janine R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-11-08

    There are many sources of variability that exist in the sample collection and analysis process. This paper addresses many, but not all, sources of variability. The main focus of this paper was to better understand and estimate variability due to differences between samplers. Variability between days was also studied, as well as random variability within each sampler. Experiments were performed using multiple surface materials (ceramic and stainless steel), multiple contaminant concentrations (10 spores and 100 spores), and with and without the presence of interfering material. All testing was done with sponge sticks using 10-inch by 10-inch coupons. Bacillus atrophaeus was used as the BA surrogate. Spores were deposited using wet deposition. Grime was coated on the coupons which were planned to include the interfering material (Section 3.3). Samples were prepared and analyzed at PNNL using CDC protocol (Section 3.4) and then cultured and counted. Five samplers were trained so that samples were taken using the same protocol. Each sampler randomly sampled eight coupons each day, four coupons with 10 spores deposited and four coupons with 100 spores deposited. Each day consisted of one material being tested. The clean samples (no interfering materials) were run first, followed by the dirty samples (coated with interfering material). There was a significant difference in recovery efficiency between the coupons with 10 spores deposited (mean of 48.9%) and those with 100 spores deposited (mean of 59.8%). There was no general significant difference between the clean and dirty (containing interfering material) coupons or between the two surface materials; however, there was a significant interaction between concentration amount and presence of interfering material. The recovery efficiency was close to the same for coupons with 10 spores deposited, but for the coupons with 100 spores deposited, the recovery efficiency for the dirty samples was significantly larger (65

  19. 75 FR 47573 - Career and Technical Education Program-Promoting Rigorous Career and Technical Education Programs...

    Science.gov (United States)

    2010-08-06

    ... DEPARTMENT OF EDUCATION Career and Technical Education Program--Promoting Rigorous Career and Technical Education Programs of Study Catalog of Federal Domestic Assistance (CFDA) Number: 84.051C. AGENCY... Technical Education Programs of Study program. The Assistant Secretary may use this priority and these...

  20. 75 FR 29732 - Career and Technical Education Program-Promoting Rigorous Career and Technical Education Programs...

    Science.gov (United States)

    2010-05-27

    ... DEPARTMENT OF EDUCATION Career and Technical Education Program--Promoting Rigorous Career and Technical Education Programs of Study Catalog of Federal Domestic Assistance (CFDA) Number: 84.051C. AGENCY... technical education programs of study (POSs) through the use of ten key components based on the ``Program of...

  1. Final Technical Report: Results of Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Narang, David, J.; Hambrick, Joshua; Srinivasan, Devarajan; Ayyannar, Raja; O' Brien, Kathleen

    2011-09-28

    Arizona Public Service Company (APS) expects that by 2027, renewable energy will account for 6,590 GWh in energy consumption by its customers. While much of this future energy will come from large centrally-located power plants, distributed renewable energy, sited at the point of end-use will also play an important role in meeting the needs of APS customers and is expected to provide 1,734 GWh. With increasing penetration of residential and commercial photovoltaic (PV) systems at the point of end-use, PV power generation not only offsets the load, but could also cause significant shifts in power flow patterns through the distribution system, and could possibly cause reversal of flow through some branches of a distribution circuit. Significant changes to power flow introduced into existing distribution systems due to the increased amount of PV systems may cause operational issues, including over-voltage on the distribution feeder (loss of voltage regulation) and incorrect operation of control equipment, which may lead to an increase in the number of operations and related equipment wear that could affect equipment reliability and customer power quality. Additionally, connecting generation resources to a distribution feeder can introduce additional sources of short-circuit current to the distribution system. This could potentially result in increased short-circuit currents, potentially reaching damaging levels, causing protection desensitization and a potential loss of protection coordination. These effects may be further compounded by variability of PV production due to shading by clouds. The effects of these phenomena in distributed PV applications are not well understood, and there is a great need to characterize this variability. This project will contribute to understanding the effects of high-penetration solar electricity on the design and operation of distribution systems by demonstrating how a high penetration of PV systems affects grid operations of a

  2. Leadership Skills among Technical and Vocational Educators

    Science.gov (United States)

    Zakaria, Nurazyan Zahidah; Jizat, Nor Atikah Md.; Zakaria, Normah

    2015-01-01

    The purpose of leadership skills among technical and vocational educator are to prepare them towards effective organization. Effective leadership is widely accepted as being a key constituent in achieving organization improvement and to examine. This study aimed to gauge the leadership skills among technical and vocational educators effectiveness…

  3. Technical equipment in soilless production systems

    NARCIS (Netherlands)

    Os, van E.A.; Gieling, T.H.; Lieth, J.H.

    2008-01-01

    Technical innovations in fertilization and irrigation have resulted in adoption of fertigation technologies wherein completely soluble fertilizers are dissolved in irrigation water so as to deliver to plants the nutrients they need for optimal growth. This chapter focuses on the technical equipment

  4. Evaluation Study of VTAE Wood Technics Programs.

    Science.gov (United States)

    Wisconsin State Board of Vocational, Technical, and Adult Education, Madison.

    A survey of former students of the Wisconsin Vocational, Technical, and Adult Education (VTAE) wood technics programs and employers in woodworking industries was conducted during spring of 1985. General objectives were to determine job classifications, types of businesses, and relative importance of tasks or duties in various woodworking-related…

  5. Technical-scientific production of IPEN - 1992

    International Nuclear Information System (INIS)

    1993-01-01

    The technical-scientific production from Nuclear and Energetic Research Institute (IPEN), Brazil, is presented, including 471 references, where 421 papers are from the 1992 year and 50 from the earlier years. The main areas that the IPEN acts are: technical-scientific development of materials; nuclear processes; research reactors; nuclear utilization; nuclear safety and human resources formation. (C.G.C.)

  6. 18 CFR 415.42 - Technical standards.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Technical standards. 415.42 Section 415.42 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS-FLOOD PLAIN REGULATIONS Administration § 415.42 Technical standards. (a...

  7. Research Needs: Career and Technical Education

    Science.gov (United States)

    Kosloski, Michael F., Jr.; Ritz, John M.

    2016-01-01

    Research is an important component of each professional field. This study sought to determine topics that needed further research in the school subjects known as career and technical education. It determined topics that needed to be researched related to high school career and technical education (CTE) and the preparation for teaching CTE in…

  8. Administrators' Perceptions of Career and Technical Education

    Science.gov (United States)

    Haussman, Charles E.

    2012-01-01

    Career and technical education was founded on the common practice of apprenticeships integrated into the public schools at the beginning of the 20th century as manual arts, which continued to evolve into a culture and practice of its own as vocational education, and into what is now career and technical education, with an evolving focus on college…

  9. Career Technical Education Pathways Initiative Annual Report

    Science.gov (United States)

    California Community Colleges, Chancellor's Office, 2014

    2014-01-01

    California's education system--the largest in the United States--is an essential resource for ensuring strong economic growth in the state. The Career Technical Education Pathways Initiative (the Initiative) became law in 2005 with Senate Bills 70 and 1133 and provided more than $380 million over eight years to improve career technical education…

  10. 75 FR 81832 - Technical Service Provider Assistance

    Science.gov (United States)

    2010-12-29

    ... DEPARTMENT OF AGRICULTURE Natural Resources Conservation Service 7 CFR Part 652 Technical Service... as of Jan. 1, 2010, on page 565, in Sec. 652.2, the first definition for ``Technical service'' is removed. [FR Doc. 2010-32945 Filed 12-28-10; 8:45 am] BILLING CODE 1505-01-D ...

  11. Momentum in Transformation of Technical Infrastructure

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev; Elle, Morten

    1999-01-01

    Current infrastructure holds a considerable momentum and this momentum is a barrier of transformation towards more sustainable technologies and more sustainable styles of network management. Using the sewage sector in Denmark as an example of a technical infrastructure system this paper argues...... that there are technical, economical and social aspects of the current infrastructures momentum....

  12. Strategic Management of Architectural Technical Debt

    Science.gov (United States)

    2012-05-22

    SEI Agile Research Forum Twitter #SEIAgile © 2012 Carnegie Mellon University Strategic Management of Architectural Technical Debt Ipek Ozkaya...AND SUBTITLE Strategic Management of Architectural Technical Debt 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S

  13. A Preliminary Rhetoric of Technical Copywriting.

    Science.gov (United States)

    Henson, Leigh

    1994-01-01

    Discusses the rhetorical elements of technical copywriting, including its shared communicative aims with technical writing; authorship considerations such as ethics, education, and professionalism; and the concerns of promotional strategy, audience analysis, choice of media and materials, writing strategy, and style. (SR)

  14. A Taxonomy of Technical Assistance Skills.

    Science.gov (United States)

    Ogden, Evelyn; Musumeci, Marilyn

    To operationalize the Technical Assistance Brokerage System, the first major task called for the development of a taxonomy of training and technical assistance services specifying requisite skills and skill clusters by the dimensions of client type, stages of dissemination, and levels of experience. From a literature search approximately 400…

  15. 75 FR 48273 - Technical Service Provider Assistance

    Science.gov (United States)

    2010-08-10

    ... provisions by expanding the definition Technical Service Provider Assistance, which contained an error in the omission of ``Indian Tribe'' in the definition of Technical Service Provider. DATES: Effective Date: This amendment is effective on August 10, 2010. FOR FURTHER INFORMATION CONTACT: Angel Figueroa, Team Leader...

  16. Revitalizing Technical and Vocational Education Training for ...

    African Journals Online (AJOL)

    Administrator

    employment for sustainable development. Revitalizing technical and vocational education and training in Nigeria. Skill training enhances productivity and sustains competitiveness in the global economy. Worldwide countries are renewing efforts to promote technical and vocational education and training, this is because it is ...

  17. Technical and Vocational Education for Zimbabwe's Rural ...

    African Journals Online (AJOL)

    The main purpose of this paper is to highlight some issues and concerns in the Zimbabwean educational system in general, and in particular, issues and concerns within the purview for technical and vocational education. The paper will further provoke debate within the context of technical and vocational education as a ...

  18. Technical Efficiency of the Spanish Dairy

    NARCIS (Netherlands)

    Kapelko, M.; Oude Lansink, A.G.J.M.

    2013-01-01

    This chapter uses DEA to measure the technical efficiency of a sample of Spanish dairy processing firms over the period 2001–2009. Differences in technical efficiency between firms of different sizes and between firms that operated in international markets versus those that were not are tested. The

  19. Technical manual: Labour-based road construction

    OpenAIRE

    Johannessen, B.

    1997-01-01

    "The purpose of this manual is to provide technical staff from supervisors to engineers with a field reference which in detail explains and prescribes the work methods and technical standards applied when constructing rural roads using labour-based methods in Lao PDR.

  20. Teaching Students the Verticality of Technical Documentation.

    Science.gov (United States)

    Hager, Peter J.

    1992-01-01

    Advocates making technical writing courses more vertical in structure by including an extensive study of at least one specific form of technical documentation. Examines how students can gain experience in the vertical process by designing, writing, testing, and producing user manuals for on-campus cooperative education clients. Lists the benefits…

  1. Impact of Automation on Technical Services.

    Science.gov (United States)

    Rooks, Dana C.; Thompson, Linda L.

    1988-01-01

    Discusses the impact of automation on library technical services, and the need for library managers to be aware of the issues involved and to plan for future developments. The discussion focuses on the areas of job related concerns of technical staff, organizational structures, recruitment and training, and ergonomic considerations. (CLB)

  2. Technical support non-SLB(GCDF)

    International Nuclear Information System (INIS)

    DePoorter, G.L.; Burton, B.W.

    1982-01-01

    The Los Alamos National Laboratory is providing technical support for the Greater Confinement Demonstration Facility (GCDF) at the Nevada Test Site. This technical support consists of computer modeling of the GCDF, design and emplacement of a Shallow Test Plot at NTS, and instrument testing at Los Alamos. Results to date on the computer modeling and the Shallow Test Plot are described

  3. 49 CFR 845.22 - Technical panel.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Technical panel. 845.22 Section 845.22 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD... Technical panel. The Director, Bureau of Accident Investigation, or the Director, Bureau of Field Operations...

  4. Measurement Of Technical Efficiency In Irrigated Vegetable ...

    African Journals Online (AJOL)

    This study measured technical efficiency and identified its determinants in irrigated vegetable production in Nasarawa State of Nigeria using a stochastic frontier model. A complete enumeration of 193 NADP-registered vegetable farmers was done. The predicted farm technical efficiency ranges from 25.94 to 96.24 per cent ...

  5. Technical challenges of multipollutant air quality management

    National Research Council Canada - National Science Library

    Hidy, George M

    2011-01-01

    ... in implementing riskand results-based, multipollutant air quality management in North America. The intended audience for the assessment is air quality management decision-makers in Canada, the United States, and Mexico (and especially their technical staffs). However, the assessment also gives an in-depth summary of the technical issues facing cont...

  6. The Technical Student Programme draws Norwegians

    CERN Multimedia

    Maria Martin Sanchez

    2005-01-01

    Erik Hejne, second from left, Chairman of the Technical Students Committee, and Jens Vigen, who is concerned spefically with Norwegian students at CERN, with some of the Norwegian technical students who arrived at CERN in spring 2005, together with their teachers.

  7. Virtual Campus Hub technical evaluation report

    DEFF Research Database (Denmark)

    Vercoulen, Frank; Badger, Merete; Monaco, Lucio

    This report describes and discusses the technical achievements of the Virtual Campus Hub project and formulates a brief agenda for the future.......This report describes and discusses the technical achievements of the Virtual Campus Hub project and formulates a brief agenda for the future....

  8. Rooftop Solar Photovoltaic Technical Potential in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Gagnon, Pieter; Margolis, Robert; Melius, Jennifer; Phillips, Caleb; Elmore, Ryan

    2016-01-01

    How much energy could we generate if PV modules were installed on all of the suitable roof area in the nation? To answer this question, we first use GIS methods to process a lidar dataset and determine the amount of roof area that is suitable for PV deployment in 128 cities nationwide, containing 23% of U.S. buildings, and provide PV-generation results for a subset of those cities. We then extend the insights from that analysis to the entire continental United States. We develop two statistical models -- one for small buildings and one for medium and large buildings -- and populate them with geographic variables that correlate with rooftop's suitability for PV. We simulate the productivity of PV installed on the suitable roof area, and present the technical potential of PV on both small buildings and medium/large buildings for every state in the continental US. Within the 128 cities covered by lidar data, 83% of small buildings have a location suitable for a PV installation, but only 26% of the total rooftop area of small buildings is suitable for development. The sheer number of buildings in this class, however, gives small buildings the greatest technical potential. Small building rooftops could accommodate 731 GW of PV capacity and generate 926 TWh/year of PV energy, approximately 65% of rooftop PV's total technical potential. We conclude by summing the PV-generation results for all building sizes and therefore answering our original question, estimating that the total national technical potential of rooftop PV is 1,118 GW of installed capacity and 1,432 TWh of annual energy generation. This equates to 39% of total national electric-sector sales.

  9. Computational model for simulation small testing launcher, technical solution

    Science.gov (United States)

    Chelaru, Teodor-Viorel; Cristian, Barbu; Chelaru, Adrian

    2014-12-01

    The purpose of this paper is to present some aspects regarding the computational model and technical solutions for multistage suborbital launcher for testing (SLT) used to test spatial equipment and scientific measurements. The computational model consists in numerical simulation of SLT evolution for different start conditions. The launcher model presented will be with six degrees of freedom (6DOF) and variable mass. The results analysed will be the flight parameters and ballistic performances. The discussions area will focus around the technical possibility to realize a small multi-stage launcher, by recycling military rocket motors. From technical point of view, the paper is focused on national project "Suborbital Launcher for Testing" (SLT), which is based on hybrid propulsion and control systems, obtained through an original design. Therefore, while classical suborbital sounding rockets are unguided and they use as propulsion solid fuel motor having an uncontrolled ballistic flight, SLT project is introducing a different approach, by proposing the creation of a guided suborbital launcher, which is basically a satellite launcher at a smaller scale, containing its main subsystems. This is why the project itself can be considered an intermediary step in the development of a wider range of launching systems based on hybrid propulsion technology, which may have a major impact in the future European launchers programs. SLT project, as it is shown in the title, has two major objectives: first, a short term objective, which consists in obtaining a suborbital launching system which will be able to go into service in a predictable period of time, and a long term objective that consists in the development and testing of some unconventional sub-systems which will be integrated later in the satellite launcher as a part of the European space program. This is why the technical content of the project must be carried out beyond the range of the existing suborbital vehicle

  10. INTER-EXAMINER VARIABILITY

    African Journals Online (AJOL)

    Objective: To establish whether inter-examiner variability is still a significant factor for the undergraduate orthopaedic clinical ... D. The scores for each student were tabulated and the range, mean, and pass rate determined for each of the examiners. ... has not the heart to reject the man”, consistently gave higher scores (1).

  11. All Those Independent Variables.

    Science.gov (United States)

    Meacham, Merle L.

    This paper presents a case study of a sixth grade remedial math class which illustrates the thesis that only the "experimental attitude," not the "experimental method," is appropriate in the classroom. The thesis is based on the fact that too many independent variables exist in a classroom situation to allow precise measurement. The case study…

  12. Variable speed generators

    CERN Document Server

    Boldea, Ion

    2005-01-01

    With the deregulation of electrical energy production and distribution, says Boldea (Polytechnical Institute, Timisoara, Romania) producers are looking for ways to tailor their electricity for different markets. Variable-speed electric generators are serving that purpose, up to the 400 megavolt ampere unit size, in Japan since 1996 and Germany sinc

  13. Variability in GPS sources

    NARCIS (Netherlands)

    Jauncey, DL; King, EA; Bignall, HE; Lovell, JEJ; Kedziora-Chudczer, L; Tzioumis, AK; Tingay, SJ; Macquart, JP; McCulloch, PM

    2003-01-01

    Flux density monitoring data at 2.3 and 8.4 GHz is presented for a sample of 33 southern hemisphere GPS sources, drawn from the 2.7 GHz Parkes survey. This monitoring data, together with VLBI monitoring data, shows that a small fraction of these sources, similar to10%, vary. Their variability falls

  14. Validation and Variability

    DEFF Research Database (Denmark)

    Carusi, Annamaria

    2014-01-01

    Systems biology is currently making a bid to show that it is able to make an important contribution to personalised or precision medicine. In order to do so, systems biologists need to find a way of tackling the pervasive variability of biological systems that is manifested in the medical domain...

  15. Surfing wave climate variability

    Science.gov (United States)

    Espejo, Antonio; Losada, Iñigo J.; Méndez, Fernando J.

    2014-10-01

    International surfing destinations are highly dependent on specific combinations of wind-wave formation, thermal conditions and local bathymetry. Surf quality depends on a vast number of geophysical variables, and analyses of surf quality require the consideration of the seasonal, interannual and long-term variability of surf conditions on a global scale. A multivariable standardized index based on expert judgment is proposed for this purpose. This index makes it possible to analyze surf conditions objectively over a global domain. A summary of global surf resources based on a new index integrating existing wave, wind, tides and sea surface temperature databases is presented. According to general atmospheric circulation and swell propagation patterns, results show that west-facing low to middle-latitude coasts are more suitable for surfing, especially those in the Southern Hemisphere. Month-to-month analysis reveals strong seasonal variations in the occurrence of surfable events, enhancing the frequency of such events in the North Atlantic and the North Pacific. Interannual variability was investigated by comparing occurrence values with global and regional modes of low-frequency climate variability such as El Niño and the North Atlantic Oscillation, revealing their strong influence at both the global and the regional scale. Results of the long-term trends demonstrate an increase in the probability of surfable events on west-facing coasts around the world in recent years. The resulting maps provide useful information for surfers, the surf tourism industry and surf-related coastal planners and stakeholders.

  16. Spatial Variability of Rainfall

    DEFF Research Database (Denmark)

    Jensen, N.E.; Pedersen, Lisbeth

    2005-01-01

    As a part of a Local Area Weather Radar (LAWR) calibration exercise 15 km south of Århus, Denmark, the variability in accumulated rainfall within a single radar pixel (500 by 500 m) was measured using nine high-resolution rain gauges. The measured values indicate up to a 100% variation between...

  17. Several real variables

    CERN Document Server

    Kantorovitz, Shmuel

    2016-01-01

    This undergraduate textbook is based on lectures given by the author on the differential and integral calculus of functions of several real variables. The book has a modern approach and includes topics such as: •The p-norms on vector space and their equivalence •The Weierstrass and Stone-Weierstrass approximation theorems •The differential as a linear functional; Jacobians, Hessians, and Taylor's theorem in several variables •The Implicit Function Theorem for a system of equations, proved via Banach’s Fixed Point Theorem •Applications to Ordinary Differential Equations •Line integrals and an introduction to surface integrals This book features numerous examples, detailed proofs, as well as exercises at the end of sections. Many of the exercises have detailed solutions, making the book suitable for self-study. Several Real Variables will be useful for undergraduate students in mathematics who have completed first courses in linear algebra and analysis of one real variable.

  18. Integration i flere variable

    DEFF Research Database (Denmark)

    Markvorsen, Steen

    2010-01-01

    -integralerne. Undervejs introduceres \\texttt{Integrator8}. Det er en pakke med Maple procedurer, som er udviklet specielt med henblik på eksempelbaseret visuel læring af de indledende integrationsbegreber og deres mangfoldige anvendelser. Vi giver eksempler på, hvordan integration i flere variable anvendes til beregning...

  19. Variable Oakleaf Caterpillar

    Science.gov (United States)

    Louis F. Wilson; Gordon A. Surgeoner

    1979-01-01

    The variable oakleaf caterpillar (Heterocampa manteo (Dbldy.)) is a common insect in deciduous forests of Eastern North America. It has been recorded from most of the Eastern Canadian Provinces and most of the States in the East to North Dakota in the West and south to eastern Texas, Louisiana, and Mississippi. Heavy defoliations of hosts may occur anywhere within this...

  20. Variability and component composition

    NARCIS (Netherlands)

    T. van der Storm (Tijs)

    2004-01-01

    textabstractIn component-based product populations, feature models have to be described at the component level to be able to benefit from a product family approach. As a consequence, composition of components becomes very complex. We describe how component-level variability can be managed in the

  1. Contribution of Co-Skewness and Co-Kurtosis of the Higher Moment CAPM for Finding the Technical Efficiency

    Directory of Open Access Journals (Sweden)

    Md. Zobaer Hasan

    2014-01-01

    Full Text Available The objective of this paper is to present the technical efficiency of individual companies and their respective groups of Bangladesh stock market (i.e., Dhaka Stock Exchange, DSE by using two risk factors (co-skewness and co-kurtosis as the additional input variables in the Stochastic Frontier Analysis (SFA. The co-skewness and co-kurtosis are derived from the Higher Moment Capital Asset Pricing Model (H-CAPM. To investigate the contribution of these two factors, two types of technical efficiency are derived: (1 technical efficiency with considering co-skewness and co-kurtosis (WSK and (2 technical efficiency without considering co-skewness and co-kurtosis (WOSK. By comparing these two types of technical efficiency, it is noticed that the technical efficiency of WSK is higher than the technical efficiency of WOSK for the individual companies and their respective groups. As per available literature in the context Bangladesh stock market, no study has been conducted thus far to measure technical efficiency of companies and their respective groups by using the risk factors which are derived from the H-CAPM. In this research, the link between H-CAPM and SFA is established for measuring technical efficiency and it is believed that the findings of this study may be applied to other emerging stock markets.

  2. Net-Zero Energy Technical Shelter

    DEFF Research Database (Denmark)

    Zhang, Chen; Heiselberg, Per; Jensen, Rasmus Lund

    2014-01-01

    Technical shelters are the basic structures for storing electronic and technical equipment, and commonly used for telecommunication base station, windmill, gas station, etc. Due to their high internal heat load density and special operation schedule, they consume more energy than normal residential...... or commercial buildings. On the other hand, it is a big challenge to power the technical shelter in remote area where the grids are either not available or the expansion of grid is expensive. In order to minimize the energy consumption and obtain a reliable and cost-efficient power solution for technical...... shelter, this study will apply the net-zero energy concept into the technical shelter design. The energy conservation can be achieved by proper design of building envelop and optimization of the cooling strategies. Both experiments and numerical simulations are carried out to investigate the indoor...

  3. The technical report - a necessary evil

    International Nuclear Information System (INIS)

    Koch, H.

    1978-01-01

    The article is meant mainly for students and for those starting their working life. First of all, the question is discussed why a technical report ought to be written. The technical report serves to rethink own activities, the documentation of one's own work as regards those who ordered it, and to inform the own organization and third parties of the state of technical development. This is followed by a discussion of the requirements made on a technical report, namely adaptation to the aims to be achieved, a good breakdown of subjects, a good linguistic style, and good graphical representation of results. There are numerous DIN standards which are useful when working out technical reports. The standards are quoted. (orig.) [de

  4. Tides and Decadal Variability

    Science.gov (United States)

    Ray, Richard D.

    2003-01-01

    This paper reviews the mechanisms by which oceanic tides and decadal variability in the oceans are connected. We distinguish between variability caused by tides and variability observed in the tides themselves. Both effects have been detected at some level. The most obvious connection with decadal timescales is through the 18.6-year precession of the moon's orbit plane. This precession gives rise to a small tide of the same period and to 18.6-year modulations in the phase and amplitudes of short-period tides. The 18.6-year "node tide" is very small, no more than 2 cm anywhere, and in sea level data it is dominated by the ocean's natural Variability. Some authors have naively attributed climate variations with periods near 19 years directly to the node tide, but the amplitude of the tide is too small for this mechanism to be operative. The more likely explanation (Loder and Garrett, JGR, 83, 1967-70, 1978) is that the 18.6-y modulations in short-period tides, especially h e principal tide M2, cause variations in ocean mixing, which is then observed in temperature and other climatic indicators. Tidally forced variability has also been proposed by some authors, either in response to occasional (and highly predictable) tidal extremes or as a nonlinear low-frequency oscillation caused by interactions between short-period tides. The former mechanism can produce only short-duration events hardly more significant than normal tidal ranges, but the latter mechanism can in principle induce low-frequency oscillations. The most recent proposal of this type is by Keeling and Whorf, who highlight the 1800-year spectral peak discovered by Bond et al. (1997). But the proposal appears contrived and should be considered, in the words of Munk et al. (2002), "as the most likely among unlikely candidates."

  5. TECHNICAL TRAINING SEMINAR: National Instruments

    CERN Multimedia

    Monique Duval

    2004-01-01

    From 9:30 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Data acquisition systems on PCs, industrial measurement and control techniques, advanced LabVIEW software and PXI instrumentation, and system components for tests and automation will be presented. Walk-in courses will address DIAdem, LabVIEW and data acquisition. Language: English and French Free seminars and courses, no registration Organisers: Rolf Stampfli / IT-CO / 78102 & 160367 / Rolf.Stampfli@cern.ch Davide Vitè / HR-PMD-ATT / 75141 Davide.Vite@cern.ch For more information and the complete event programme, please visit the...

  6. Internal stability of technical superconductors

    International Nuclear Information System (INIS)

    Kastner, K.

    1985-09-01

    Electrical stability and longitudinal quench propagation velocity of technical NbTi superconductors having various matrix compositions was investigated experimentally and theoretically (numerically) for different cooling conditions. Copper, cupro-nickel and both combined were used as matrix materials of the conductors. The measurements were performed between 5 and 8 K in vacuum and at 4.2 K in helium both applying magnetic fields up to 7 T. The quantitative agreement between experiments and calculations was better than a factor of 2 regarding all 8 specimen at the investigated environmental conditions (cooling, temperature, and magnetic field). The remaining uncertainty is mainly conditioned by the accumulation of small inaccuracies in knowledge of the various conductor parameters, but far less to be found in the computer program itself. The accuracy of these parameters cannot be further improved with reasonable effort and expenditure. It is shown, that position and fraction of the cupro-nickel barriers inside the mixed matrix conductors affect strongly quench propagation velocity; stability also is sensible to these parameters. The strong effect on quench propagation velocity may be explained by a feedback mechanism. A way is given, how to change stability and quench propagation velocity of a mixed matrix conductor by constructional measures without implicating an enhancement of the coupling current losses. (orig.) [de

  7. Scientific and Technical Report, 1997

    International Nuclear Information System (INIS)

    Metivier, Henri; Mur, Emmanuelle

    1998-01-01

    This report highlights the most significant scientific and technical achievements of the Institute of Nuclear Protection and Safety in 1997. In all 23 reports are grouped in the following 7 sections: 1.Reactor safety; 2.Safety of nuclear facility; 3.Safeguards for radioactive materials and transports; 4.Public protection; 5.Environment protection; 6.Radioactive waste safety; 7.Crisis management. Special attention is paid to the pressurized water and fast neutron reactors and, accordingly, the program PHEBUS PF and the first results obtained with it concerning nuclear safety are reported. The safety of nuclear fuel cycle and spent fuel storage is addressed in a couple of reports, as well as the problem of inspection, measurement and containers for nuclear materials. Concerning the public and environment protection, studies are reported on medical surveillance of people working with CEA Group, and clinical dosimetric follow-up of radiological events as well as the strategy of contaminated site rehabilitation. In the field of radioactive waste management, the IPSN project of Tournemire tunnel and the project of deep disposal are presented. Finally, the issue of major nuclear accidents is approached through the exercise Becquerel, the SESAME system of predicting the radioactive products release in PWR reactors and ASTRAL, the evaluation system of aftermath of an accidental environmental contamination by radioactive release. Each section of this IPSN report is opened by a review paper

  8. Technical errors in MR arthrography

    Energy Technology Data Exchange (ETDEWEB)

    Hodler, Juerg [Orthopaedic University Hospital of Balgrist, Radiology, Zurich (Switzerland)

    2008-01-15

    This article discusses potential technical problems of MR arthrography. It starts with contraindications, followed by problems relating to injection technique, contrast material and MR imaging technique. For some of the aspects discussed, there is only little published evidence. Therefore, the article is based on the personal experience of the author and on local standards of procedures. Such standards, as well as medico-legal considerations, may vary from country to country. Contraindications for MR arthrography include pre-existing infection, reflex sympathetic dystrophy and possibly bleeding disorders, avascular necrosis and known allergy to contrast media. Errors in injection technique may lead to extra-articular collection of contrast agent or to contrast agent leaking from the joint space, which may cause diagnostic difficulties. Incorrect concentrations of contrast material influence image quality and may also lead to non-diagnostic examinations. Errors relating to MR imaging include delays between injection and imaging and inadequate choice of sequences. Potential solutions to the various possible errors are presented. (orig.)

  9. Technical basis for dose reconstruction

    International Nuclear Information System (INIS)

    Anspaugh, L.R.

    1996-01-01

    The purpose of this paper is to consider two general topics: technical considerations of why dose-reconstruction studies should or should not be performed and methods of dose reconstruction. The first topic is of general and growing interest as the number of dose-reconstruction studies increases, and one asks the question whether it is necessary to perform a dose reconstruction for virtually every site at which, for example, the Department of Energy (DOE) has operated a nuclear-related facility. And there is the broader question of how one might logically draw the line at performing or not performing dose-reconstruction (radiological and chemical) studies for virtually every industrial complex in the entire country. The second question is also of general interest. There is no single correct way to perform a dose-reconstruction study, and it is important not to follow blindly a single method to the point that cheaper, faster, more accurate, and more transparent methods might not be developed and applied

  10. Technical Evolution of Medical Endoscopy

    Directory of Open Access Journals (Sweden)

    S. Gross

    2009-01-01

    Full Text Available This paper gives a summary of the technical evolution of medical endoscopy. The first documented redirection of sunlight into the human body dates back to the 16th century. Rigid tubes with candle light were given a trial later on. Low light intensity forced the development of alternative light sources. Some of these experiments included burning chemical components. Electric lighting finally solved the problems of heat production and smoke. Flexible endoscopy increased the range of medical examinations as it allowed access to tight and angular body cavities. The first cameras for endoscopic applications made taking photos from inside the human body possible. Later on, digital video endoscopy made endoscopes easier to use and allowed multiple spectators to observe the endoscopic intervention. Swallowable capsules called pill-cams made endoscopic examinations of the small intestine possible. Modern technologies like narrow band imaging and fluorescence endoscopy increased the diagnostic significance of endoscopic images. Today, image processing is applied to decrease noise and enhance image quality. These enhancements have made medical endoscopy an invaluable tool in many diagnostic processes. In closing, an example is given of an interdisciplinary examination, which is taken from the archaeological field. 

  11. 1990 Resource Program : Technical Report.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1990-07-01

    This Technical Report is a detailed presentation of the actions Bonneville Power Administration (BPA) will take to develop new resources to meet the power requirements of its customers. The primary focus of this report is on what BPA will do in Fiscal Years (FY's) 1992 and 1993. However, much care has been taken to define near-term actions aimed at meeting BPA's long-term needs. An aggressive, steadily increasing conservation program forms the foundation of the 1990 Resource Program and resource acquisitions for FY's 1992 and 1993. BPA's commitment to a steady ramp-up of the conservation program is key to achieving the least-cost approach to resource development, and to making the conservation resource deliverable in the long run. By itself, conservation can meet much of the likely range of load growth that BPA faces. A diverse mix of generation resources in small increments is the second cornerstone of the 1990 Resource Program. These generation resources can meet the rest of the likely range of BPA resource needs. Finally, a Resource Contingency Plan prepares BPA to reliably meet load in the event that load growth exceeds the likely range. 14 figs., 27 tabs.

  12. Technical errors in MR arthrography

    International Nuclear Information System (INIS)

    Hodler, Juerg

    2008-01-01

    This article discusses potential technical problems of MR arthrography. It starts with contraindications, followed by problems relating to injection technique, contrast material and MR imaging technique. For some of the aspects discussed, there is only little published evidence. Therefore, the article is based on the personal experience of the author and on local standards of procedures. Such standards, as well as medico-legal considerations, may vary from country to country. Contraindications for MR arthrography include pre-existing infection, reflex sympathetic dystrophy and possibly bleeding disorders, avascular necrosis and known allergy to contrast media. Errors in injection technique may lead to extra-articular collection of contrast agent or to contrast agent leaking from the joint space, which may cause diagnostic difficulties. Incorrect concentrations of contrast material influence image quality and may also lead to non-diagnostic examinations. Errors relating to MR imaging include delays between injection and imaging and inadequate choice of sequences. Potential solutions to the various possible errors are presented. (orig.)

  13. TECHNICAL COORDINATION, SCHEDULE AND INTEGRATION

    CERN Document Server

    A. Ball

    Introduction Since the lowering of YB0 in February, less spectacular but nonetheless crucial progress has been made along the critical path to CMS completion. The YB0 has been aligned with the beamline to a fraction of a mm, and the HCAL has been fully installed. Cabling scaffolding for YB0 services has been built and one half (-z end) of the ECAL barrel has been installed. The YB0 services installation has begun, with two of the major technical challenges delaying bulk installation, namely PP1 detailed design, manufacture and installation plus Tracker cooling pipe insulation, now apparently solved. Significant difficulties in detailed design, integration and procurement of cable ducts remain. Despite this, the design of the +end is close to complete, and Tracker power cable installation on two sectors of the +end is well advanced. A new master schedule, v36.0, is being prepared to account for the updated actual situation at point 5 and for the revised LHC machine planning. Safety The enormous amount of...

  14. Final Scientific/Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Yale [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory; Thomas, Michael E. [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory; Siegrist, Karen M. [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory; Lennon, Andrew M. [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory; Hunter, Lawrence W. [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory; Oguz, Hasan O. [Johns Hopkins University, Laurel, MD (United States). Applied Physics Laboratory

    2014-06-30

    JHU/APL conducted solid propellant fire characterization tests in warm, humid, ambient conditions near sea level. Yttria and ceria surrogate materials were placed in the fires. The substrates simulating ground surfaces were concrete from a Kennedy Space Center launch pad, and steel covered with a protective ablative material representing a launch platform. In-situ instrumentation consisted of witness materials, thermocouples, air handlers, filters, and cascade impactors; remote instrumentation consisted of optical cameras and spectrometers. Test and analysis team members included the Naval Air Warfare Center Aircraft Division, Sandia National Laboratories (SNL), Alliant Techsystems, and the Johns Hopkins University. Test data were analyzed, reported, and delivered, including plume rise and transport captured on video. Derivation of the alumina particle size distributions formed the basis for condensing vapor and agglomeration estimates. Assessment of alumina mass in the plume, along with the surrogate fraction from filter forensics, provided an estimate of airborne surrogate mass. Technical interchange meetings were held with SNL and the Jet Propulsion Laboratory. Specifications for the fire environment were developed and delivered. A thermochemistry model that simultaneously provides the maximum temperature and heat flux was developed and delivered. An SPIE paper on 3D pyrometry of the fire was written and presented.

  15. [Lengthening temporalis myoplasty: Technical refinements].

    Science.gov (United States)

    Guerreschi, P; Labbé, D

    2015-10-01

    First described by Labbé in 1997, the lengthening temporalis myoplasty (LTM) ensures the transfer of the entire temporal muscle from the coronoid process to the upper half of the lip without interposition of aponeurotic tissue. Thanks to brain plasticity, the temporal muscle is able to change its function because it is entirely mobilized towards another effector: the labial commissure. After 6 months of speech rehabilitation, the muscle loses its chewing function and it acquires its new smiling function. We describe as far as possible all the technical points to guide surgeons who would like to perform this powerful surgical procedure. We show the coronoid process approaches both through an upper temporal fossa approach and a lower nasolabial fold approach. Rehabilitation starts 3 weeks after the surgery following a standardized protocol to move from a mandibular smile to a voluntary smile, and then a spontaneous smile in 3 steps. The LTM is the main part of a one-stage global treatment of the paralyzed face. It constitutes a dynamic palliative treatment usually started at the sequelae stage, 18 months after the outcome of a peripheral facial paralysis. This one-stage procedure is a reproducible and relevant surgical technique in the difficult treatment of peripheral facial paralysis. An active muscle is transferred to reanimate the labial commissure and to recreate a mobile nasolabial fold. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

  16. Technical and economic analysis of the European electricity system with 60% RES

    International Nuclear Information System (INIS)

    Burtin, Alain; Silva, Vera

    2015-01-01

    This document examines the impacts of the integration of a large share of variable renewable generation into the generation mix of the European interconnected electricity system. The analysis, which is based on the results of long term studies performed by EDF R and D, aims at improving the current understanding of the technical and economic feasibility of a massive deployment of wind and PV across the European system. The document addresses several aspects of the system integration of variable generation in particular, including the characterization of variable RES generation, the need for generation and interconnection infrastructure, the impacts on short-term system operation and market profitability. (authors)

  17. Simulation fails to replicate stress in trainees performing a technical procedure in the clinical environment.

    Science.gov (United States)

    Baker, B G; Bhalla, A; Doleman, B; Yarnold, E; Simons, S; Lund, J N; Williams, J P

    2017-01-01

    Simulation-based training (SBT) has become an increasingly important method by which doctors learn. Stress has an impact upon learning, performance, technical, and non-technical skills. However, there are currently no studies that compare stress in the clinical and simulated environment. We aimed to compare objective (heart rate variability, HRV) and subjective (state trait anxiety inventory, STAI) measures of stress theatre with a simulated environment. HRV recordings were obtained from eight anesthetic trainees performing an uncomplicated rapid sequence induction at pre-determined procedural steps using a wireless Polar RS800CX monitor © in an emergency theatre setting. This was repeated in the simulated environment. Participants completed an STAI before and after the procedure. Eight trainees completed the study. The theatre environment caused an increase in objective stress vs baseline (p = .004). There was no significant difference between average objective stress levels across all time points (p = .20) between environments. However, there was a significant interaction between the variables of objective stress and environment (p = .045). There was no significant difference in subjective stress (p = .27) between environments. Simulation was unable to accurately replicate the stress of the technical procedure. This is the first study that compares the stress during SBT with the theatre environment and has implications for the assessment of simulated environments for use in examinations, rating of technical and non-technical skills, and stress management training.

  18. Technological Capability's Predictor Variables

    Directory of Open Access Journals (Sweden)

    Fernanda Maciel Reichert

    2011-03-01

    Full Text Available The aim of this study was to identify the factors that influence in configuration of the technological capability of companies in sectors with medium-low technological intensity. To achieve the goal proposed in this article a survey was carried out. Based on the framework developed by Lall (1992 which classifies firms in basic, intermediate and advanced level of technological capability; it was found that the predominant technological capability is intermediate, with 83.7% of respondent companies (plastics companies in Brazil. It is believed that the main contribution of this study is the finding that the dependent variable named “Technological Capability” can be explained at a rate of 65% by six variables: development of new processes; selection of the best equipment supplier; sales of internally developed new technology to third parties; design and manufacture of equipment; study of the work methods and perform inventory control; and improvement of product quality.

  19. Technical report, GANIL E416

    International Nuclear Information System (INIS)

    Kirsch, Robert

    2003-01-01

    The document LYCEN-RI--2003-28 is a technical report of the Institut de Physique Nucleaire-Lyon, given on June, 2003, concerning the 5 axis goniometer of INDRA, at GANIL (Grand Accelerateur National d'Ions Lourds). The contents of this report is as follows: 1.1. Experiment proposal; 1.2. Technical requirements; 1.2.1. Characteristics of the goniometer system; 1.2.2. Initial specifications of motions; 1.2.3. An overlook to INDRA; 2. Mechanical characteristics; 2.1. Study; 2.1.1. Goniometer structural support; 2.1.2. Goniometer off-set head; 2.1.3. Passage to INDRA; 2.1.4. Assembly parts of goniometer structural support and goniometer off-set head; 2.1.5. Target exchanger hopper; 2.1.6. Vacuum chamber for mechanical manoeuvres; 2.1.7. Goniometer support made of commercial plates; 2.1.8. The goniometer off-set head studied and built at IPN-Lyon; 2.1.9. Assembly parts, target exchanger hopper, vacuum chamber for mechanical manoeuvres; 2.1.10. Stainless steel vacuum welding for mechanical structures; 2.1.11. Preliminary cleaning for vacuum; 2.2. Assemblage; 2.3. BE and workshop; 2.4. Directions of motions of goniometer head; 2.5. File transfer between Catia and SolidEdge; 3. The electronics of motorization; 3.1. Overlook; 3.2. Connections of Microcontrol standard drivers; 3.3. Passage through vacuum - SubD25 connectors; 3.4. Safety box (SB); 3.4.1. Driver phases; 3.4.2. Ends of drivers strokes; 3.4.3. INDRA safety; 3.4.4. Emergency shutdown; 3.5. ESP7000; 3.5.1. Configuration; 3.5.2. Digital I/O connection to INDRA automat through the SubD50 connector; 3.5.3. Reduction of the shutdown current; 3.5.4. Remote control; 3.5.5. Configuration file of the ESP7000 display; 3.5.6. Configuration files of the five ESP7000 power cards; 4. Software; 4.1. Manual for simplified use of goniometer control program; 4.2. 'Expert' use of the goniometer control program; 4.2.2. RS232 connection window; 4.2.3. Control driver window; 5. Single crystals; 5.1. Preparation; 5.2. Crystal supports

  20. Historical Variable Star Catalogs

    OpenAIRE

    Pagnotta, Ashley; Graur, Or; Murray, Zachary; Kruk, Julia; Christie-Dervaux, Lucien; Chen, Dong Yi

    2015-01-01

    Slides from my talk during one of the Historical Astronomy Division sessions at AAS 225 in Seattle, WA (January 2015). A brief history of the variable star catalogs Henrietta Swan Leavitt and Cecilia Payne-Gaposchkin assembled at Harvard, and the update to them that some of our students at AMNH have done.(Figshare only previews the first few slides. Download the PDF to see all of them!)

  1. Complex variable HVPT

    Energy Technology Data Exchange (ETDEWEB)

    Killingbeck, John P [Mathematics Department, University of Hull, Hull HU6 7RX (United Kingdom); Grosjean, Alain [Laboratoire d' Astrophysique de l' Observatoire de Besancon (CNRS, UPRES-A 6091), 41 bis Avenue de l' Observatoire, BP 1615, 25010 Besancon Cedex (France); Jolicard, Georges [Laboratoire d' Astrophysique de l' Observatoire de Besancon (CNRS, UPRES-A 6091), 41 bis Avenue de l' Observatoire, BP 1615, 25010 Besancon Cedex (France)

    2004-08-13

    Complex variable hypervirial perturbation theory is applied to the case of oscillator and Coulomb potentials perturbed by a single term potential of the form Vx{sup n} or Vr{sup n}, respectively. The trial calculations reported show that this approach can produce accurate complex energies for resonant states via a simple and speedy calculation and can also be useful in studies of PT symmetry and tunnelling resonance effects. (addendum)

  2. Georeactor Variability and Integrity

    OpenAIRE

    Herndon, J. Marvin

    2005-01-01

    As a deep-Earth energy source, the planetocentric nuclear-fission georeactor concept is on a more secure scientific footing than the previous idea related to the assumed growth of the inner core. Unlike previously considered deep-Earth energy sources, which are essentially constant on a human time-scale, variability in nuclear fission reactors can arise from changes in composition and/or position of fuel, moderators, and neutron absorbers. Tantalizing circumstantial evidence invites inquiry i...

  3. Spreading with variable viscosity

    OpenAIRE

    Foit, J.J.

    1997-01-01

    Ausbreitung mit variabler Viskosität Die isotherme Ausbreitung eines Volumenstromes, , in Form von dünnen Schichten kann mit Hilfe selbstähnlicher Lösungen beschrieben werden (Huppert). Für die axialsymmetrische Ausbreitung eines konstanten Volumens mit einer variablen Viskosität von der Form existieren ebenfalls selbstähnliche Lösungen (Sakimoto, Zuber). Dieses Ergebnis wird auf den Fall einer eindimensionalen und einer axialsymmetrischen Ausbreitung für alle , erweitert.

  4. TEC variability over Havana

    International Nuclear Information System (INIS)

    Lazo, B.; Alazo, K.; Rodriguez, M.; Calzadilla, A.

    2003-01-01

    The variability of total electron content (TEC) measured over Havana using ATS-6, SMS-1 and GOES-3 geosynchronous satellite signals has been investigated for low, middle and high solar activity periods from 1974 to 1982. The obtained results show that standard deviation is smooth during nighttime hours and maximum at noon or postnoon hours. Strong solar activity dependence of standard deviation with a maximum values during HSA has been found. (author)

  5. Short timescale variability in the faint sky variability survey

    NARCIS (Netherlands)

    Morales-Rueda, L.; Groot, P.J.; Augusteijn, T.; Nelemans, G.A.; Vreeswijk, P.M.; Besselaar, E.J.M. van den

    2006-01-01

    We present the V-band variability analysis of the Faint Sky Variability Survey (FSVS). The FSVS combines colour and time variability information, from timescales of 24 minutes to tens of days, down to V = 24. We find that �1% of all point sources are variable along the main sequence reaching �3.5%

  6. Classifying TDSS Stellar Variables

    Science.gov (United States)

    Amaro, Rachael Christina; Green, Paul J.; TDSS Collaboration

    2017-01-01

    The Time Domain Spectroscopic Survey (TDSS), a subprogram of SDSS-IV eBOSS, obtains classification/discovery spectra of point-source photometric variables selected from PanSTARRS and SDSS multi-color light curves regardless of object color or lightcurve shape. Tens of thousands of TDSS spectra are already available and have been spectroscopically classified both via pipeline and by visual inspection. About half of these spectra are quasars, half are stars. Our goal is to classify the stars with their correct variability types. We do this by acquiring public multi-epoch light curves for brighter stars (rpulsating white dwarfs, and other exotic systems. The key difference between our catalog and others is that along with the light curves, we will be using TDSS spectra to help in the classification of variable type, as spectra are rich with information allowing estimation of physical parameters like temperature, metallicity, gravity, etc. This work was supported by the SDSS Research Experience for Undergraduates program, which is funded by a grant from Sloan Foundation to the Astrophysical Research Consortium.

  7. Variable Cycle Engine Technology Program Planning and Definition Study

    Science.gov (United States)

    Westmoreland, J. S.; Stern, A. M.

    1978-01-01

    The variable stream control engine, VSCE-502B, was selected as the base engine, with the inverted flow engine concept selected as a backup. Critical component technologies were identified, and technology programs were formulated. Several engine configurations were defined on a preliminary basis to serve as demonstration vehicles for the various technologies. The different configurations present compromises in cost, technical risk, and technology return. Plans for possible variably cycle engine technology programs were formulated by synthesizing the technology requirements with the different demonstrator configurations.

  8. Continuous Variable Quantum Key Distribution with a Noisy Laser

    DEFF Research Database (Denmark)

    Jacobsen, Christian Scheffmann; Gehring, Tobias; Andersen, Ulrik Lund

    2015-01-01

    Existing experimental implementations of continuous-variable quantum key distribution require shot-noise limited operation, achieved with shot-noise limited lasers. However, loosening this requirement on the laser source would allow for cheaper, potentially integrated systems. Here, we implement...... a theoretically proposed prepare-and-measure continuous-variable protocol and experimentally demonstrate the robustness of it against preparation noise stemming for instance from technical laser noise. Provided that direct reconciliation techniques are used in the post-processing we show that for small distances...

  9. THE DIMENSIONS OF CREATIVITY IN TECHNICAL EDUCATION

    Directory of Open Access Journals (Sweden)

    Małgorzata Franc

    2016-06-01

    Full Text Available Introduction: this paper engages with the change in the approach to technical education and to its research nature, quantity and quality ratio. The technical education is ordinary education and technical education at the same time. The technical education is a set of activities aimed at the skillful use of technology in deliberately organized process of interacting with an individual, causing permanent changes in their personality. Formation of a learner’s technological culture is made by providing knowledge about the products of technology, experiencing technical situations, raising respect for human technical creativity and products of creativity, developing an ability to use the products of technology. Technical education is aimed at the student’s cognitive realm, providing information and building a system of knowledge about the technical reality, developing cognitive skills needed to receive, understand, interpret and verify technical phenomena. Materials and Methods: the research was based on the analysis of students’ theses enrolled at Organization and Management Faculty of Lodz University of Technology. Results: objective quality indicators were defined for the purposes of analysis. The analysis results are not final, but they form the basis for an in-depth understanding of the academic reality. Generic requirements have been developed to polytechnic education. Discussion and Conclusions: polytechnic education is a specific link in the development of culture and civilization that provides value to the formation of personality. Different areas of the human civilization and the objective socio-cultural world are the basis for development. Polytechnic education forms the elite, providing the stable development of the society in accordance with the rules and principles.

  10. Designing neural networks that process mean values of random variables

    Energy Technology Data Exchange (ETDEWEB)

    Barber, Michael J. [AIT Austrian Institute of Technology, Innovation Systems Department, 1220 Vienna (Austria); Clark, John W. [Department of Physics and McDonnell Center for the Space Sciences, Washington University, St. Louis, MO 63130 (United States); Centro de Ciências Matemáticas, Universidade de Madeira, 9000-390 Funchal (Portugal)

    2014-06-13

    We develop a class of neural networks derived from probabilistic models posed in the form of Bayesian networks. Making biologically and technically plausible assumptions about the nature of the probabilistic models to be represented in the networks, we derive neural networks exhibiting standard dynamics that require no training to determine the synaptic weights, that perform accurate calculation of the mean values of the relevant random variables, that can pool multiple sources of evidence, and that deal appropriately with ambivalent, inconsistent, or contradictory evidence. - Highlights: • High-level neural computations are specified by Bayesian belief networks of random variables. • Probability densities of random variables are encoded in activities of populations of neurons. • Top-down algorithm generates specific neural network implementation of given computation. • Resulting “neural belief networks” process mean values of random variables. • Such networks pool multiple sources of evidence and deal properly with inconsistent evidence.

  11. Industrial espionage and technical surveillance counter measurers

    CERN Document Server

    Androulidakis, Iosif

    2016-01-01

    This book examines technical aspects of industrial espionage and its impact in modern companies, organizations, and individuals while emphasizing the importance of intellectual property in the information era. The authors discuss the problem itself and then provide statistics and real world cases. The main contribution provides a detailed discussion of the actual equipment, tools and techniques concerning technical surveillance in the framework of espionage. Moreover, they present the best practices and methods of detection (technical surveillance counter measures) as well as means of intellectual property protection.

  12. TWRS technical baseline database manager definition document

    International Nuclear Information System (INIS)

    Acree, C.D.

    1997-01-01

    This document serves as a guide for using the TWRS Technical Baseline Database Management Systems Engineering (SE) support tool in performing SE activities for the Tank Waste Remediation System (TWRS). This document will provide a consistent interpretation of the relationships between the TWRS Technical Baseline Database Management software and the present TWRS SE practices. The Database Manager currently utilized is the RDD-1000 System manufactured by the Ascent Logic Corporation. In other documents, the term RDD-1000 may be used interchangeably with TWRS Technical Baseline Database Manager

  13. Technical specification optimization program - engineered safety features

    International Nuclear Information System (INIS)

    Andre, G.R.; Jansen, R.L.

    1986-01-01

    The Westinghouse Technical Specification Program (TOP) was designed to evaluate on a quantitative basis revisions to Nuclear Power Plant Technical Specifications. The revisions are directed at simplifying plant operation, and reducing unnecessary transients, shutdowns, and manpower requirements. In conjunction with the Westinghouse Owners Group, Westinghouse initiated a program to develop a methodology to justify Technical Specification revisions; particularly revisions related to testing and maintenance requirements on plant operation for instrumentation systems. The methodology was originally developed and applied to the reactor trip features of the reactor protection system (RPS). The current study further refined the methodology and applied it to the engineered safety features of the RPS

  14. Book Review: New Perspectives on Technical Editing

    Science.gov (United States)

    Murphy, A. J. (Ed.); Sterken, Christiaan

    2012-08-01

    New Perspectives on Technical Editing by Avon J. Murphy (ed.) ISBN : 978-0895033949 (2010) Baywood Publishing Company Inc, Hardcover, 210 pages, 35.5 GBP This book presents a collection of 10 chapters dealing with diverse aspects of technical editing (ie, editorial planning, and analysis and structural changes made to other people's technological documents): research in technical editing, trends and teaching of technical editing, copyediting, and technical journal editing. The role and function of the modern journal and book editor is also dealt with in detail. Each chapter is written by an expert in the field: senior editors, university professors in technical communication, technical writers and linguists. The ever-evolving role of the editor is clearly elucidated in several historical reviews, and in the descriptions of the expectations for the future. A very striking aspect of this book is its extensive collection of bibliographic resources: every chapter lists dozens of very useful references, and the closing chapter, and annotated bibliography, contain many not so well known references, and are most useful. All in all, the book is a treasure trove listing more than 400 references, in addition to numerous webpage URLs embedded in the texts. The book is designed to help the reader to understand current practices and norms in technical editing, and to help to take action in editing as well as in teaching and educating would-be editors. The audience for this book thus includes editors and teachers, but also writers, researchers and students. A deep reading of this book will result in a better understanding of the difference between full technical editing and its much narrower component so well known as copyediting, and will convince any prospective editor that editing should not be undertaken if the people involved do not master the art of precision and accuracy in technical (as well as in human) communication, do not possess the technical know how and computer

  15. Standard technical specifications combustion engineering plants

    International Nuclear Information System (INIS)

    1992-09-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS) for Combustion Engineering Plants. The improved STS wee developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. This document, Volume 1, contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Sections 3.4--3.9 of the improved STS

  16. Are general surgeons able to accurately self-assess their level of technical skills?

    Science.gov (United States)

    Rizan, C; Ansell, J; Tilston, T W; Warren, N; Torkington, J

    2015-11-01

    Self-assessment is a way of improving technical capabilities without the need for trainer feedback. It can identify areas for improvement and promote professional medical development. The aim of this review was to identify whether self-assessment is an accurate form of technical skills appraisal in general surgery. The PubMed, MEDLINE(®), Embase(™) and Cochrane databases were searched for studies assessing the reliability of self-assessment of technical skills in general surgery. For each study, we recorded the skills assessed and the evaluation methods used. Common endpoints between studies were compared to provide recommendations based on the levels of evidence. Twelve studies met the inclusion criteria from 22,292 initial papers. There was no level 1 evidence published. All papers compared the correlation between self-appraisal versus an expert score but differed in the technical skills assessment and the evaluation tools used. The accuracy of self-assessment improved with increasing experience (level 2 recommendation), age (level 3 recommendation) and the use of video playback (level 3 recommendation). Accuracy was reduced by stressful learning environments (level 2 recommendation), lack of familiarity with assessment tools (level 3 recommendation) and in advanced surgical procedures (level 3 recommendation). Evidence exists to support the reliability of self-assessment of technical skills in general surgery. Several variables have been shown to affect the accuracy of self-assessment of technical skills. Future work should focus on evaluating the reliability of self-assessment during live operating procedures.

  17. Progress report: Variable Energy Cyclotron Centre, Calcutta

    International Nuclear Information System (INIS)

    1999-01-01

    This volume of the progress report brings out the scientific and technical activities of Variable Energy Cyclotron Centre, Calcutta during the year 1999. This includes brief review of the various R and D activities of the Centre and outside users of the cyclotron from the universities and other research institutes. The operational activities of the cyclotron with ECR ion sources, accelerator oriented research activities, activities on detector, target and electronics are reported. The activities of the Computer and Informatics group are described. The status report of the ongoing projects is also provided. The main activities of the superconducting cyclotron project, radioactive ion beam project, heavy ion experimental facility, advanced computational facility, recovery and analysis of helium from hot springs and material science research are described

  18. Technical note: A stereological analysis of the cross-sectional variability of the femoral osteon population

    DEFF Research Database (Denmark)

    Villa, Chiara; Lynnerup, Niels

    2010-01-01

    Unbiased selection of regions of interest (ROIs) and unbiased definition of histological structures are needed to improve the repeatability of microscopic methods for age at death determination and to reduce operator subjectivity. We present results obtained by selecting ROIs according to stereol...

  19. A Model for Using Qualitative Variables as Covariates in the Analysis of Covariance. Technical Paper 266.

    Science.gov (United States)

    Ross, N. Phillip

    The U.S. Army Research Institute for the Behavioral and Social Sciences has developed a wide range of statistical models to test hypotheses generated in relation to an equally wide range of measurement and evaluation situations. The randomized block (RB) design has traditionally been a preferred model for much psychological research. The RB has…

  20. 75 FR 20817 - Information Systems Technical Advisory Committee

    Science.gov (United States)

    2010-04-21

    ... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... Administration on technical questions that affect the level of export controls applicable to information systems...