Importance for Municipalities of Infrastructure Information Systems in Turkey

OpenAIRE

Kamil KARATAS; Cemal BIYIK

2017-01-01

Technical infrastructures are the important development-level parameters of countries, difficult to maintain and require high-investment cost. It is required to take the advantage of information system for the better administration of technical infrastructure facilities, planning and taking effective decisions. Hence, infrastructure information systems must be built oriented to technical infrastructure (TI). In this study, Kunduracilar Street in Trabzon was selected as pilot area oriented to ...

The Acoustical Presentation of Technical Information.

Science.gov (United States)

Barnett, George A.

1992-01-01

Advocates listening to technical information in much the same way as scientists and engineers look at graphics to understand the relationships among variables. Specifies a number of potential benefits of this approach. Demonstrates the presentation of acoustic information with data on the frequency of television viewing from 1950 to 1988. (SR)

Information technologies in technical education

OpenAIRE

Кравченя, Э. М.

2013-01-01

The purpose of researches is working out of the concept of filling of discipline «Information and computer technologies in formation» the first step of higher education entered into curricula was at engineering-pedagogical faculty BNTU. It is shown that as a result of discipline studying there is an expansion of outlook and formation at students of technical college of independent thinking in the field of modern and perspective information technology.

New Approaches for Navy Technical Training and Job Performance Aiding Using Expanded IETM Technology

National Research Council Canada - National Science Library

Jorgensen, Eric L; Fuller, Joseph J

1996-01-01

...) began to develop better ways to present Technical Information (TI) to Navy Fleet users needed for purposes of operating, maintaining, training, and logistically supporting the Navy's inventory of weapon systems...

Transportation Technical Environmental Information Center index

Energy Technology Data Exchange (ETDEWEB)

Davidson, C. A.; Foley, J. T.

1980-10-01

In an effort to determine the environmental intensities to which energy materials in transit may be exposed, a Data Center of technical environmental information has been established by Sandia National Laboratories, Division 5523, for the DOE Office of Transportation Fuel Storage. This document is an index which can be used to request data of interest. Access to the information held is not limited to Sandia personnel. The purpose of the Transportation Technical Environmental Information Center is to collect, analyze, store, and make available descriptions of the environment of transportation expressed in engineering terms. The data stored in the Center are expected to be useful in a variety of transportation related analyses. Formulations of environmental criteria for shipment of cargo, risk assessments, and detailed structural analyses of shipping containers are examples where these data have been applied. For purposes of indexing and data retrieval, the data are catalogued under two major headings: Normal and Abnormal Environments.

Transportation Technical Environmental Information Center index

International Nuclear Information System (INIS)

Davidson, C.A.; Foley, J.T.

1980-10-01

In an effort to determine the environmental intensities to which energy materials in transit may be exposed, a Data Center of technical environmental information has been established by Sandia National Laboratories, Division 5523, for the DOE Office of Transportation Fuel Storage. This document is an index which can be used to request data of interest. Access to the information held is not limited to Sandia personnel. The purpose of the Transportation Technical Environmental Information Center is to collect, analyze, store, and make available descriptions of the environment of transportation expressed in engineering terms. The data stored in the Center are expected to be useful in a variety of transportation related analyses. Formulations of environmental criteria for shipment of cargo, risk assessments, and detailed structural analyses of shipping containers are examples where these data have been applied. For purposes of indexing and data retrieval, the data are catalogued under two major headings: Normal and Abnormal Environments

Study on information dissemination for effective nuclear risk communication

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

The aim of this study are to develop an information system and guideline for nuclear risk communication between expert and citizens as well as between both experts in terms of lessons learned from serious disaster such as Fukushima Dai-ich NPP accident. Technical standards for disseminating a result and process of seismic/tsunami PRA (Probabilistic Risk Assessment) of nuclear facility as well as nuclear risk information in an emergency, and risk communication in normal times are needed. Tins study examines the framework, contents, and technical basis for developing an information system for nuclear risk communication. In addition, this study identifies the communication issues of nuclear risk communication concerning the seismic/tsunami PRA through the testing information systems in areas around nuclear facilities and by providing effective implementation guidelines. JNES has developed the information system specified as Protection of Nuclear Power Plants against Tsunamis and Post Earthquake considerations in the External Zone (TiPEEZ) as part of IAEA International Seismic Safety Centre (ISSC) Extra Budgetary Programme (EBP). The EBP is currently preparing technical documents (TECDOC) regarding the implementation of the TiPEEZ. After the Fukushima accident, there has been increasing demand for disaster mitigation systems to share risk information between nuclear organizations and local municipalities. JNES and Niigata Institute of Technology conduct implementation of TiPEEZ for the practical use based on the corroborative works with Kashiwazaki city and citizens. (author)

Study on information dissemination for effective nuclear risk communication

International Nuclear Information System (INIS)

2013-01-01

The aim of this study are to develop an information system and guideline for nuclear risk communication between expert and citizens as well as between both experts in terms of lessons learned from serious disaster such as Fukushima Dai-ich NPP accident. Technical standards for disseminating a result and process of seismic/tsunami PRA (Probabilistic Risk Assessment) of nuclear facility as well as nuclear risk information in an emergency, and risk communication in normal times are needed. Tins study examines the framework, contents, and technical basis for developing an information system for nuclear risk communication. In addition, this study identifies the communication issues of nuclear risk communication concerning the seismic/tsunami PRA through the testing information systems in areas around nuclear facilities and by providing effective implementation guidelines. JNES has developed the information system specified as Protection of Nuclear Power Plants against Tsunamis and Post Earthquake considerations in the External Zone (TiPEEZ) as part of IAEA International Seismic Safety Centre (ISSC) Extra Budgetary Programme (EBP). The EBP is currently preparing technical documents (TECDOC) regarding the implementation of the TiPEEZ. After the Fukushima accident, there has been increasing demand for disaster mitigation systems to share risk information between nuclear organizations and local municipalities. JNES and Niigata Institute of Technology conduct implementation of TiPEEZ for the practical use based on the corroborative works with Kashiwazaki city and citizens. (author)

Internet application: production-technical information system MoNET

International Nuclear Information System (INIS)

Tomiga, J.

2004-01-01

MoNET is the production-technical information system supporting engineering, operational and maintenance processes of distribution network administrator. It utilizes the model of distribution network that is situated in the geo-space relational database. The geo-space database represents an information base of operational-technical processes. It contains elements and equipment s of the distribution network, failures, operational events, maintenance records, but also, parcels, reference planimetry, e.g. and other subjects for which is relevant the positional datum - geo-space information. MoNET is typically exploited in the fields: - evidence of the subjects and equipment of network, technical documentation; - property administration; - planning of network development, support of designing and construction; - technical calculation; - breakdown controller centre; - maintenance management. MoNET can be implemented as the desktop application, however its first benefit is derived from its usage as the intranet application MoNET WEB for the whole enterprise or organisation. This version enables an unrestricted number of end-users to enter this system. The end-users don't need any special software to enter the data of MoNet WEB application, the pre-installed Internet Explorer will do. (author)

THE OFFICE OF AEROSPACE RESEARCH SCIENTIFIC AND TECHNICAL INFORMATION PROGRAM

Science.gov (United States)

The document outlines the mission and organization of the Office of Aerospace Research (OAR), then describes how its principal product, scientific...effective technical information program, are documented by examples. The role of the Office of Scientific and Technical Information within OAR as performed

Transportation Technical Environmental Information Center index

Energy Technology Data Exchange (ETDEWEB)

Davidson, C.A.; Foley, J.T.

1982-06-01

In an effort to determine the environmental intensities to which energy materials in transit may be exposed, a Data Center of technical environmental information has been established by Sandia National Laboratories, Division 5523, for the DOE Office of Transportation Fuel Storage. This document is an index which can be used to request data of interest. Access to the information held is not limited to Sandia personnel.

Transportation Technical Environmental Information Center index

International Nuclear Information System (INIS)

Davidson, C.A.; Foley, J.T.

1982-06-01

In an effort to determine the environmental intensities to which energy materials in transit may be exposed, a Data Center of technical environmental information has been established by Sandia National Laboratories, Division 5523, for the DOE Office of Transportation Fuel Storage. This document is an index which can be used to request data of interest. Access to the information held is not limited to Sandia personnel

Contextual Sensing: Integrating Contextual Information with Human and Technical Geo-Sensor Information for Smart Cities.

Science.gov (United States)

Sagl, Günther; Resch, Bernd; Blaschke, Thomas

2015-07-14

In this article we critically discuss the challenge of integrating contextual information, in particular spatiotemporal contextual information, with human and technical sensor information, which we approach from a geospatial perspective. We start by highlighting the significance of context in general and spatiotemporal context in particular and introduce a smart city model of interactions between humans, the environment, and technology, with context at the common interface. We then focus on both the intentional and the unintentional sensing capabilities of today's technologies and discuss current technological trends that we consider have the ability to enrich human and technical geo-sensor information with contextual detail. The different types of sensors used to collect contextual information are analyzed and sorted into three groups on the basis of names considering frequently used related terms, and characteristic contextual parameters. These three groups, namely technical in situ sensors, technical remote sensors, and human sensors are analyzed and linked to three dimensions involved in sensing (data generation, geographic phenomena, and type of sensing). In contrast to other scientific publications, we found a large number of technologies and applications using in situ and mobile technical sensors within the context of smart cities, and surprisingly limited use of remote sensing approaches. In this article we further provide a critical discussion of possible impacts and influences of both technical and human sensing approaches on society, pointing out that a larger number of sensors, increased fusion of information, and the use of standardized data formats and interfaces will not necessarily result in any improvement in the quality of life of the citizens of a smart city. This article seeks to improve our understanding of technical and human geo-sensing capabilities, and to demonstrate that the use of such sensors can facilitate the integration of different

Contextual Sensing: Integrating Contextual Information with Human and Technical Geo-Sensor Information for Smart Cities

Science.gov (United States)

Sagl, Günther; Resch, Bernd; Blaschke, Thomas

2015-01-01

In this article we critically discuss the challenge of integrating contextual information, in particular spatiotemporal contextual information, with human and technical sensor information, which we approach from a geospatial perspective. We start by highlighting the significance of context in general and spatiotemporal context in particular and introduce a smart city model of interactions between humans, the environment, and technology, with context at the common interface. We then focus on both the intentional and the unintentional sensing capabilities of today’s technologies and discuss current technological trends that we consider have the ability to enrich human and technical geo-sensor information with contextual detail. The different types of sensors used to collect contextual information are analyzed and sorted into three groups on the basis of names considering frequently used related terms, and characteristic contextual parameters. These three groups, namely technical in situ sensors, technical remote sensors, and human sensors are analyzed and linked to three dimensions involved in sensing (data generation, geographic phenomena, and type of sensing). In contrast to other scientific publications, we found a large number of technologies and applications using in situ and mobile technical sensors within the context of smart cities, and surprisingly limited use of remote sensing approaches. In this article we further provide a critical discussion of possible impacts and influences of both technical and human sensing approaches on society, pointing out that a larger number of sensors, increased fusion of information, and the use of standardized data formats and interfaces will not necessarily result in any improvement in the quality of life of the citizens of a smart city. This article seeks to improve our understanding of technical and human geo-sensing capabilities, and to demonstrate that the use of such sensors can facilitate the integration of different

Protecting safeguards information / Division of technical support

International Nuclear Information System (INIS)

2002-01-01

This DVD contains two films representing the key aspects of the IAEA Department of Safeguards. 'Protecting Safeguards Information' is a narrative/fiction film which presents the Agency's information handling and protection measures. A security representative from a fictional nation receives a briefing on the procedures and methods used by the Department. These techniques will assure member states that the information they provide to the Agency is kept safe and confidential. 'Division of Technical Support' is a non-fiction documentary which presents a detailed look at the technical capabilities and management techniques used by the Agency in nuclear material accountancy. The film covers many aspects of safeguards equipment and techniques including: NDA and DA instruments, seals, surveillance, training, development and maintenance. Taken together, these films provide an introduction and overview to many important aspects of the IAEA Department of Safeguards. (IAEA)

Computers in technical information transfer

Energy Technology Data Exchange (ETDEWEB)

Price, C.E.

1978-01-01

The use of computers in transferring scientific and technical information from its creation to its use is surveyed. The traditional publication and distribution processes for S and T literature in past years have been the vehicle for transfer, but computers have altered the process in phenomenal ways. Computers are used in literature publication through text editing and photocomposition applications. Abstracting and indexing services use computers for preparing their products, but the machine-readable document descriptions created for this purpose are input to a rapidly growing computerized information retrieval service industry. Computer use is making many traditional processes passe, and may eventually lead to a largely ''paperless'' information utility.

Prototype for an automated technical specification information system

International Nuclear Information System (INIS)

Quinn, E.L.; Mills, R.H.; Groves, J.E.

1985-01-01

The Southern California Edison (SCE) Automated Technical Specification Information System (ATSIS) at the San Onofre nuclear generating station (SONGS) has been developed as a prototype for an on-line information management system. This system provides an appropriate level of update, inquiry, and report generation capabilities to help support plant operators at SONGS in their efforts to anticipate, identify, document, and track certain actions and activities associated with plant technical specifications and associated limiting conditions of operation (LCOs). Substantially increased emphasis is being placed on adherence to nuclear regulatory requirements and commitments contained on the operating licenses of nuclear power plants. Additionally, as each year passes, such requirements are becoming increasingly detailed and complex, making it more and more difficult to track and ensure total compliance with the many and varied requirements. To assist the operations department at SONGs in meeting their regulatory commitments, in January 1985 SCE commenced gathering together the leading technical expertise available in the industry to develop a computerized system to track all technical specification-related equipment for operability and impact on LCOs

Scientific and technical information output of the Langley Research Center

Science.gov (United States)

1984-01-01

Scientific and technical information that the Langley Research Center produced during the calendar year 1983 is compiled. Included are citations for Formal Reports, Quick-Release Technical Memorandums, Contractor Reports, Journal Articles and other Publications, Meeting Presentations, Technical Talks, Computer Programs, Tech Briefs, and Patents.

Role of the Technical Information Center in the knowledge management

International Nuclear Information System (INIS)

Morales, Alfredo; Marrero, Carmen; Aguero, Manuel

1999-01-01

Competitive advantage of companies is directly proportional to their capacity for creating, capturing, handling, inventorying, transferring information, and generating knowledge, as well as for implementing best practices, in order to add value to the production process. Creation of an environment that allows carrying out this process efficiently, constitutes a transcendental step toward the systematic and useful application of knowledge management. This paper presents the role of Technical Information Centers, as entities which provide and integrate information and knowledge, within knowledge communities. The Technical Information Center (CIT for the Spanish: Centro de Information Tecnica) of PDVSA-Intevep and its contribution to strengthen the corporate technological intelligence through the information analysis and technical-scientific knowledge diffusion is also analyzed. The petrochemical and petroleum information network (RIPPET) and its data base RIPPET (from the Spanish Red de Informacion Petrolera y Petroquimica), coordinate by the CIT, and the CIT on line, a virtual organization, are also presented. Both are tools which facilitate the transfer of information and knowledge to communities organized within the company to manage knowledge

The Oak Ridge Technical Information Center: A trailblazer in federal documentation

Energy Technology Data Exchange (ETDEWEB)

Vaden, W.M.

1992-01-01

This document attempts to record the history of US AEC`s Technical Information Center, from its conception (1947) to 1977. This organization centralizes and manages the issues related to control and dissemination of technical information, to fulfill the provisions of the Atomic Energy Act of 1946. TIC tried to search out and install efficient and economical systems for servicing the various technical information programs. It coordinated a direct organization-to-organization information exchange program, and it also participated in official bilateral exchange programs and in developing information systems for IAEA and Euratom. The work, planning, and strategies employed to achieve goals are chronicled in this document, with 18 chapters arranged into four sections according to different presidential administrations.

Managerial Cost Accounting for a Technical Information Center.

Science.gov (United States)

Helmkamp, John G.

A two-fold solution to the cost information deficiency problem is proposed. A formal managerial cost accounting system is designed expressly for the two information services of retrospective search and selective dissemination. The system was employed during a trial period to test its effectiveness in a technical information center. Once…

Hanford sitewide grounwater remediation - supporting technical information

International Nuclear Information System (INIS)

Chiaramonte, G.R.

1996-05-01

The Hanford Sitewide Groundwater Remediation Strategy was issued in 1995 to establish overall goals for groundwater remediation on the Hanford Site. This strategy is being refined to provide more detailed justification for remediation of specific plumes and to provide a decision process for long-range planning of remediation activities. Supporting this work is a comprehensive modeling study to predict movement of the major site plumes over the next 200 years to help plan the remediation efforts. The information resulting from these studies will be documented in a revision to the Strategy and the Hanford Site Groundwater Protection Management Plan. To support the modeling work and other studies being performed to refine the strategy, this supporting technical information report has been produced to compile all of the relevant technical information collected to date on the Hanford Site groundwater contaminant plumes. The primary information in the report relates to conceptualization of the source terms and available history of groundwater transport, and description of the contaminant plumes. The primary information in the report relates to conceptualization of the source terms and available history of groundwater transport, description of the contaminant plumes, rate of movement based on the conceptual model and monitoring data, risk assessment, treatability study information, and current approach for plume remediation

STRUCTURAL AND FUNCTIONAL MODEL OF FORMING INFORMATIONAL COMPETENCE OF TECHNICAL UNIVERSITY STUDENTS

Directory of Open Access Journals (Sweden)

Taras Ostapchuk

2016-11-01

Full Text Available The article elaborates and analyses the structural and functional model of formation of information competence of technical university students. The system and mutual relationships between its elements are revealed. It is found out that the presence of the target structure of the proposed model, process and result-evaluative blocks ensure its functioning and the opportunity to optimize the learning process for technical school students’ information training. It is established that the formation of technical university students’ information competence based on components such as motivational value, as well as operational activity, cognitive, and reflexive one. These criteria (motivation, operational and activity, cognitive, reflective, indexes and levels (reproductive, technologized, constructive forming technical university students’ information competence are disclosed. Expediency of complex organizational and educational conditions in the stages of information competence is justified. The complex organizational and pedagogical conditions include: orientation in the organization and implementation of class work for technical university students’ positive value treatment; the issue of forming professionalism; informatization of educational and socio-cultural environment of higher technical educational institutions; orientation of technical university students’ training to the demands of European and international standards on information competence as a factor in the formation of competitiveness at the labor market; introducing a special course curriculum that will provide competence formation due to the use of information technology in professional activities. Forms (lecture, visualization, problem lecture, combined lecture, scientific online conference, recitals, excursions, etc., tools (computer lab, multimedia projector, interactive whiteboard, multimedia technology (audio, video, the Internet technologies; social networks, etc

The Oak Ridge Technical Information Center: A trailblazer in federal documentation

Energy Technology Data Exchange (ETDEWEB)

Vaden, W.M.

1992-01-01

This softbound book attempts to record the history of US AEC's Technical Information Center, from its conception (1947) to 1977. This organization centralizes and manages the issues related to control and dissemination of technical information, to fulfill the provisions of the Atomic Energy Act of 1946. TIC tried to search out and install efficient and economical systems for servicing the various technical information programs. It coordinated a direct organization-to-organization information exchange program, and it also participated in official bilateral exchange programs and in developing information systems for IAEA and Euratom. The work, planning, and strategies employed to achieve goals are chronicled in this book, whose 18 chapters are arranged into four sections according to different presidential administrations.

Transportation Technical Environmental Information Center index

International Nuclear Information System (INIS)

Davidson, C.A.; Foley, J.T.

1979-01-01

In an effort to determine the environmental intensities to which energy materials in transit may be exposed, a ''Data Center'' of technical environmental information has been established by Sandia Laboratories, Division 5522, for the DOE Division of Environmental Control Technology. An index is presented which can be used to request data of interest

Technical and Management Information System (TMIS)

Science.gov (United States)

Rau, Timothy R.

1987-01-01

The TMIS goals developed to support the Space Station Program (SSP) mission requirements are outlined. The TMIS will provide common capabilities to all SSP centers and facilitate the flow of technical and management information throughout the program as well as SSP decision-making processes. A summary is presented of the various TMIS phases.

How to find technical information. Vol. 1. 2. rev. ed.

International Nuclear Information System (INIS)

Joswig, W.; Heidtmann, F.

1987-01-01

This introduction into the technique of finding and procuring special technical literature is addressed to students and post-graduate students engaged in this work. The part on library organization contains a sketch on how to procure information, while the part dealing with bibliographical material lists the most important instruments for the retrieval of special technical information. A library and bibliographical terminology and an index are appended. (DG) [de

TMI-2 Technical Information and Examination Program. 1982 annual report

International Nuclear Information System (INIS)

1983-04-01

The Department of Energy's Technical Information and Examination Program at Three Mile Island Unit 2 continued the research and development work begun on the island in 1980. The work concentrated in seven major areas: instrumentation and electrical components, radiation and environment, core activities, information and industry coordination, configuration and document control, waste immobilization, and reactor evaluation. The program assists in resolving specific problems at TMI-2 while developing techniques and broadening understanding of accident consequences to improve the overall safety and reliability of nuclear power. The Technical Information and Examination Program aims to communicate applicable information to the nuclear power industry to ensure that the industry can avail itself of the maximum amount of information possible

TMI-2 Technical Information and Examination Program 1983 annual report

International Nuclear Information System (INIS)

Scardena, D.E.

1984-04-01

The Department of Energy's Technical Information and Examination Program at Three Mile Island Unit 2 continued the research and development work begun on the Island in 1980. The work concentrated in six major areas: waste immobilization, reactor evaluation, data acquisition, information and industry coordination, core activities, and EPICOR II and waste research and disposition. The program assists in resolving specific problems at TMI-2 while developing techniques and broadening understanding of accident consequences to improve the overall safety and reliability of nuclear power. The Technical Information and Examination Program aims to communicate applicable information to the nuclear power industry to ensure that the industry can avail itself to the maximum amount of information possible

Gestionnaire, Relations d'affaires en technologie de l'information (TI ...

International Development Research Centre (IDRC) Digital Library (Canada)

Résumé des fonctions En tant que membre de l'équipe de direction de la Division ... et la maintenance d'un système de technologie de l'information (TI) intégré en ... d'un contrat de consultation), évaluer les propositions et choisir la meilleure.

Study on advanced systematic function of the JNC geological disposal technical information integration system. Research document

International Nuclear Information System (INIS)

Ishihara, Yoshinao; Fukui, Hiroshi; Sagawa, Hiroshi; Matsunaga, Kenichi; Ito Takaya

2004-02-01

In this study, while attaining systematization about the technical know-how mutually utilized between geology environmental field, disposal technology (design) field and safety assessment field, the share function of general information in which the formation of an information share and the use promotion between the technical information management databases built for every field were aimed at as an advancement of the function of JNC Geological Disposal Technical Information Integration System considered, and the system function for realizing considered in integration of technical information. (1) Since the concrete information about geology environment which is gradually updated with progress of stratum disposal research, or increases in reflected suitable for research of design and safety assessment. After arranging the form suitable for systematizing technical information, while arranging the technical information in both the fields of design and safety assessment with the form of two classes based on tasks/works, it systematized planning adjustment about delivery of technical information with geology environmental field. (2) In order to aim at integration of 3-fields technical information of geological disposal, based on the examination result of systematization of technical information, the function of mutual use of the information managed in two or more databases was considered. Moreover, while considering system functions, such as management of the use history of technical information, connection of information use, and a notice of common information, the system operation windows in consideration of the ease of operation was examined. (author)

75 FR 39919 - Information Systems, Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2010-07-13

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems, Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... export controls applicable to information systems equipment and technology. Wednesday, July 28 Public...

75 FR 64258 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2010-10-19

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... export controls applicable to information systems equipment and technology. Wednesday, November 3 Public...

78 FR 63162 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2013-10-23

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... of export controls applicable to information systems equipment and technology. Wednesday, November 6...

78 FR 42753 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2013-07-17

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... of export controls applicable to information systems equipment and technology. Wednesday, July 31...

76 FR 64895 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2011-10-19

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... export controls applicable to information systems equipment and technology. Wednesday, November 2 Public...

76 FR 39845 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2011-07-07

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... export controls applicable to information systems equipment and technology. Wednesday, July 27 Public...

78 FR 1198 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2013-01-08

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... to information systems equipment and technology. Wednesday, January 23 Open Session 1. Welcome and...

77 FR 37652 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2012-06-22

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... that affect the level of export controls applicable to information systems equipment and technology...

77 FR 1666 - Information Systems, Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2012-01-11

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems, Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... information systems equipment and technology. Wednesday, January 25 Open Session 1. Welcome and Introductions...

Improving technical information use: what can be learnt from a manager's perspective?

Science.gov (United States)

Jacobson, C; Lisle, A; Carter, R W; Hockings, M T

2013-07-01

Conservation practice reportedly suffers from low use of technical information. Understanding of factors that affect the influence of technical information on management decision-making is limited. We sought to identify leverage points for improved technical information dissemination in the New South Wales Parks and Wildlife Service, Australia, given the significant recent investments in monitoring and evaluation that had been made. We did so by exploring the inter-relationships between factors affecting the influence of different information types on management decisions. Results indicate that managers have a high inclination toward adaptive behavior, given they operate in an information poor environment. The most influential types of information were those that enabled interaction between information provider and recipient (e.g., staff experience and expertise). An analysis of the concordance in individuals' responses for different information types showed that neither accessibility nor organizational expectation of use was aligned with influence on decision-making. Alignment of responses also varied by work area. Raising expectations of information use or increasing access to particular types of information is therefore unlikely to result in an increase in influence on management decision-making. Rather than focussing on matching accessibility and expected use of particular information types, our results indicate that technical information uptake is best supported through existing peer networks tailored to specific work areas.

78 FR 24160 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2013-04-24

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... controls applicable to information systems equipment and technology. Tuesday, May 7 Open Session 1. Welcome...

77 FR 24178 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2012-04-23

... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting The Information Systems Technical Advisory Committee (ISTAC... controls applicable to information systems equipment and technology. Tuesday, May 8 Open Session 1. Welcome...

Development of TRITN : In-house technical information network of Technical Research Institute in The Chugoku Electric Power Co., Inc.

Science.gov (United States)

Ebara, Hisao

With the increase in information amount, progress in information network, diversified technology and change in in-house organization the Technical Research Institute has necessitated to shift the conventional technical database processing by use of personal computers into new system promised for future use. It enables to; provide classification system which meets the needs of the institute; execute distributed processing using workstations; make the low cost processing using commercial softwares; make networks using LAN, WAN personal computer communication, and provide primary materials (text data) on facsimiles using optical disks. Such features are those of technical information database system "TRITN" which is available to any persons and at any time. This paper describes how TRITN was developed and the system outline.

78 FR 64146 - 30-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Science.gov (United States)

2013-10-25

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY: Office of the Chief Information Officer, HUD. ACTION: Notice. SUMMARY: HUD has submitted the proposed... Information Collection Title of Information Collection: Technical Processing Requirements for Multifamily...

Integrating public information activities on a technical project

International Nuclear Information System (INIS)

Little, Sh. K.; Vecchiola, S.F.

1984-01-01

Through gradual evolution and successful performance, the WIPP Communications group has gained respect and recognition as a dual service organization that offers numerous benefits to a technical project. Westinghouse assembled a team that has successfully coordinated and encouraged an exchange of information not only with the public information realm but also as a project service and function. WIPP has combined educational services, external and employee communication and public information into one unit called ''Communications''

A study on decision-making framework for developing risk-informed technical specifications

International Nuclear Information System (INIS)

Kim, Beom Seock

2002-02-01

The utility and the nuclear research institutes in Korea have conduct research for improving inefficient requirements in technical specifications using the results of probability risk assessments and information associated with risk. However, the guidance for reviewing the improved technical specifications has not been developed. Thus, the objective of this study is to develop a decision-making framework for investigating and reviewing the documents associated with the changes of technical specifications. This work has been done for helping the regulation agency to review the improved technical specifications as well as to make decisions whether the remedy is accepted or not. The contents of this study include: 1. Surveys on Technical Specification regulations in foreign countries as well as those in Korea 2. Surveys on the state- of- the- art methodology for Risk Informed Technical Specifications and their uses in Korea 3. Development of a decision-making framework in both the licensee and the regulation agency position 4. Development and applications of a decision-making framework using Influence Diagrams. The decision-making framework for RITS using Influence Diagrams are developed and applied to an example problem in this study. This work might contribute to developing the risk informed regulation guidance for improving the quality of the current technical specifications

E-KIT: An Electronic-Knowledge Information Tool for Organizing Site Information and Improving Technical Communication with Stakeholders - 13082

International Nuclear Information System (INIS)

Kautsky, Mark; Findlay, Richard C.; Hodges, Rex A.

2013-01-01

Managing technical references for projects that have long histories is hampered by the large collection of documents, each of which might contain discrete pieces of information relevant to the site conceptual model. A database application has been designed to improve the efficiency of retrieving technical information for a project. Although many databases are currently used for accessing analytical and geo-referenced data, applications designed specifically to manage technical reference material for projects are scarce. Retrieving site data from the array of available references becomes an increasingly inefficient use of labor. The electronic-Knowledge Information Tool (e-KIT) is designed as a project-level resource to access and communicate technical information. The e-KIT is a living tool that grows as new information becomes available, and its value to the project increases as the volume of site information increases. Having all references assembled in one location with complete reference citations and links to elements of the site conceptual model offers a way to enhance communication with outside groups. The published and unpublished references are incorporated into the e-KIT, while the compendium of references serves as a complete bibliography for the project. (authors)

E-KIT: An Electronic-Knowledge Information Tool for Organizing Site Information and Improving Technical Communication with Stakeholders - 13082

Energy Technology Data Exchange (ETDEWEB)

Kautsky, Mark [U.S. Department of Energy Office of Legacy Management, 2597 Legacy Way, Grand Junction CO 81503 (United States); Findlay, Richard C.; Hodges, Rex A. [Stoller LMS Team, 2597 Legacy Way, Grand Junction CO 81503 (United States)

2013-07-01

Managing technical references for projects that have long histories is hampered by the large collection of documents, each of which might contain discrete pieces of information relevant to the site conceptual model. A database application has been designed to improve the efficiency of retrieving technical information for a project. Although many databases are currently used for accessing analytical and geo-referenced data, applications designed specifically to manage technical reference material for projects are scarce. Retrieving site data from the array of available references becomes an increasingly inefficient use of labor. The electronic-Knowledge Information Tool (e-KIT) is designed as a project-level resource to access and communicate technical information. The e-KIT is a living tool that grows as new information becomes available, and its value to the project increases as the volume of site information increases. Having all references assembled in one location with complete reference citations and links to elements of the site conceptual model offers a way to enhance communication with outside groups. The published and unpublished references are incorporated into the e-KIT, while the compendium of references serves as a complete bibliography for the project. (authors)

Evaluation of the Radiography Program at Caldwell Community College and Technical Institute--Summer, 1982.

Science.gov (United States)

Pipes, V. David

As part of a periodic evaluation of the occupational programs at Caldwell Community College and Technical Institute (CCC&TI), a study of the radiography program was conducted to collect information to facilitate planning, aid in program improvement, and meet accountability demands. The specific objectives of the program evaluation were to…

Discussion to the effects and development of nuclear geological scientific and technical information

International Nuclear Information System (INIS)

Zhang Shucheng

2010-01-01

Nuclear geological scientific and technical information has played an important role in the national economic construction and energy development, as well as exploration of uranium geology. With the increasing difficulty of prospecting, both scientific research or geological prospecting work are increasingly dependent on scientific and technical information, so, nuclear geological research and services in the scientific and technical information have become an increasing concern. From effect of the information and information resources in scientific research, the article discusses the synthesis research and services in the nuclear geological scientific and technical information, and play the role of uranium geological prospecting in the period of 'Tenth Five-Year'. In the period of the 'Eleventh Five-Year' and the coming period, the authors proposes a conception that how to strengthen the digital construction of nuclear geology scientific literature, integrative information resources and development and utilization in the network environment; and outlooks a developing prospects, that is, how to more effectively apply modern information technology, so that provides a guarantee of information resources for the scientific research and production in the new round of exploration of uranium resources. (author)

Forming Information Competence of Technical Students in Context-Based Teaching

Directory of Open Access Journals (Sweden)

G A Kruchinina

2011-12-01

Full Text Available The article considers the concept of information competence of technical students. The description of stages of forming structural components of information competence in context-based training is submitted. The results of the experiment on forming information competence of future metallurgists are given.

MODELING OF TECHNICAL CHANNELS OF INFORMATION LEAKAGE AT DISTRIBUTED CONTROL OBJECTS

Directory of Open Access Journals (Sweden)

Aleksander Vladimirovich Karpov

2018-05-01

Full Text Available The significant increase in requirements for distributed control objects’ functioning can’t be realized only at the expense of the widening and strengthening of security control measures. The first step in ensuring the information security at such objects is the analysis of the conditions of their functioning and modeling of technical channels of information leakage. The development of models of such channels is essentially the only method of complete study of their opportunities and it is pointed toward receiving quantitative assessments of the safe operation of compound objects. The evaluation data are necessary to make a decision on the degree of the information security from a leak according to the current criterion. The existing models are developed for the standard concentrated objects and allow to evaluate the level of information security from a leak on each of channels separately, what involves the significant increase in the required protective resource and time of assessment of information security on an object in general. The article deals with a logical-and-probabilistic method of a security assessment of structurally-compound objects. The model of a security leak on the distributed control objects is cited as an example. It is recommended to use a software package of an automated structurally-logistical modeling of compound systems, which allows to evaluate risk of information leakage in the loudspeaker. A possibility of information leakage by technical channels is evaluated and such differential characteristics of the safe operation of the distributed control objects as positive and negative contributions of the initiating events and conditions, which cause a leak are calculated. Purpose. The aim is a quantitative assessment of data risk, which is necessary for justifying the rational composition of organizational and technical protection measures, as well as a variant of the structure of the information security system from a

75 FR 6683 - Notice of Proposed Information Collection: Comment Request; Technical Processing Requirements for...

Science.gov (United States)

2010-02-10

... Information Collection: Comment Request; Technical Processing Requirements for Multifamily Project Mortgage... information: Title of Proposal: Technical Processing Requirements for Multifamily Project Mortgage Insurance... information collection requirement described below will be submitted to the Office of Management and Budget...

78 FR 65695 - 30-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Science.gov (United States)

2013-11-01

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY: Office of the Chief Information Officer, HUD. ACTION: Correction, notice. SUMMARY: On October 25, 2013 at... Collection Title of Information Collection: Technical Processing Requirements for Multifamily Project...

A guide to technical information regarding TMI-2 [Three Mile Island Unit 2

International Nuclear Information System (INIS)

Aucliar, K.D.; Epler, J.

1988-01-01

A considerable amount of information has been obtained and documented concerning the March 1979 accident and its consequences at the Three Mile Island Unit 2 (TMI-2) nuclear generating station. The information has been essential in (a) understanding the nature, progression, and extent of the damage from the accident; (b) assessing the effects of this damage on the plant's facilities, systems, equipment, and surrounding environment; and (c) planning, preparation, performance, and evaluation of the accident recovery activities. The composite of all of this literature is the technical information available at TMI-2. The issues raised by the accident are far-reaching and complex, and the technical information has usefulness beyond its application at TMI-2. Issues raised as a result of the accident pose questions that are technical, legal, financial, and political in nature. However, because the quantity of information is vast, this paper focuses on the technical data generated as a result of the TMI-2 accident recovery activities. Most of the written information generated during the TMI-2 recovery program was provided to meet the needs of the various key participants in the recovery. The informational needs of these groups varied widely; consequently, their motivation for record retention, content, and structure revolved around serving those needs. This paper provides some guidance to those researchers interested in investigating technical data as it relates to TMI-2

A Technical Analysis Information Fusion Approach for Stock Price Analysis and Modeling

Science.gov (United States)

Lahmiri, Salim

In this paper, we address the problem of technical analysis information fusion in improving stock market index-level prediction. We present an approach for analyzing stock market price behavior based on different categories of technical analysis metrics and a multiple predictive system. Each category of technical analysis measures is used to characterize stock market price movements. The presented predictive system is based on an ensemble of neural networks (NN) coupled with particle swarm intelligence for parameter optimization where each single neural network is trained with a specific category of technical analysis measures. The experimental evaluation on three international stock market indices and three individual stocks show that the presented ensemble-based technical indicators fusion system significantly improves forecasting accuracy in comparison with single NN. Also, it outperforms the classical neural network trained with index-level lagged values and NN trained with stationary wavelet transform details and approximation coefficients. As a result, technical information fusion in NN ensemble architecture helps improving prediction accuracy.

COMPLEMENTARY EFFECTS IN ACTIVIZATION OF SCIENTIFIC AND TECHNICAL ACTIVITIES IN THE INFORMATION SOCIETY

Directory of Open Access Journals (Sweden)

O. Zhylinska

2016-09-01

Full Text Available This paper proposes new methodological approaches in the study of development problems of scientific and technical activities in the information society. The essence and economic nature of development scientific and technical activities' from the standpoint of methodological collectivism are disclosed, a new phenomenon intensification of development scientific and technical activities by forming the global networks of scientific and technical knowledge users that provides sharing of the burden of transformation and transaction costs as generation as well as economic implementation of research and technical knowledge across the globe are showed. This study outlines the complementary effects in intensify development of scientific and technological activities components: research and development (RD, training of scientific personnel, provision of scientific and technical services, which generates of world market's complementary goods, being world market of educational services of scientific and technical information, industrial properties, high technology products, venture capital investments and stock market.

Communication of technical information to lay audiences. [National Waste Terminal Storage (NWTS) program

Energy Technology Data Exchange (ETDEWEB)

Bowes, J.E.; Stamm, K.R.; Jackson, K.M.; Moore, J.

1978-05-01

One of the objectives of the National Waste Terminal Storage (NWTS) Program is to provide terminal storage facilities for commercial radioactive wastes in various geologic formations at multiple locations in the United States. The activities performed under the NWTS Program will affect regional, state, and local areas, and widespread public interest in this program is expected. Since a large part of the NWTS Program deals with technical information it was considered desirable to initiate a study dealing with possible methods of effectively transmitting this technical information to the general public. This study has the objective of preparing a state-of-the-art report on the communication of technical information to lay audiences. The particular task of communicating information about the NWTS Program to the public is discussed where appropriate. The results of this study will aid the NWTS Program in presenting to the public the quite diverse technical information generated within the program so that a widespread, thorough public understanding of the NWTS Program might be achieved. An annotated bibliography is included.

Technical information management in an emergency response

International Nuclear Information System (INIS)

Berry, H.A.; Greve, C.; Best, R.G.; Phillipson, D.S.

1991-01-01

Through many experiences in responding to real radiation accidents and emergency response exercises, the Department of Energy (DOE) has developed a technical information management system that will be used in the Federal Radiological Monitoring and Assessment Center (FRMAC) in the event of a major radiological accident. The core of the system is the Data Center in the FRMAC, utilizing a computerized database of all off-site environmental radiological data. The information contained and managed by the Data Center will be comprehensive, accountable, and traceable, providing information to the assessors for immediate health and safety needs as well as for long-term documentation requirements. A DOE task force has been formed to develop compatibility guidelines for video, automated data processing, and communication systems. An electronic mail, information status, and bulletin board system is also being developed to assist in the dissemination of information. Geographic Information Systems (GIS) offer a giant step forward in displaying and analyzing information in a geographically referenced system

Microstructure Of A SIC/(Ti/V/Cr/Sn/Al) Composite

Science.gov (United States)

Lerch, Bradley A.; Hull, David R.; Leonhardt, Todd A.

1990-01-01

NASA technical memorandum reports on analysis of composite material made of SiC fibers in matrix of 0.76 Ti/0.15 V/0.03 Cr/0.03 Sn/0.03 Al (parts by weight) alloy. Purposes of study to investigate suitability of some metallographic techniques for use on composite materials in general and to obtain information about macrostructure and microstructure of this specific composite to provide guidance for experimental and theoretical studies of more advanced composites.

Development of the JNC geological disposal technical information integration system subjected for repository design and safety assessment

International Nuclear Information System (INIS)

Ishihara, Yoshinao; Ito, Takashi; Kobayashi, Shigeki; Neyama, Atsushi

2004-02-01

On this work, system manufacture about disposal technology and safety assessment field was performed towards construction of the JNC Geological Disposal Technical Information Integration System which systematized three fields of technical information acquired in investigation (site characteristic investigation) of geology environmental conditions, disposal technology (design of deep repository), and performance/safety assessment. The technical information database managed focusing on the technical information concerning individual research of an examination, analysis, etc. and the parameter set database managed focusing on the set up data set used in case of comprehensive evaluation are examined. In order to support and promote share and use of the technical information registered and managed by the database, utility functions, such as a technical information registration function, technical information search/browse function, analysis support function, and visualization function, are considered, and the system realized in these functions is built. The built system is installed in the server of JNC, and the functional check examination is carried out. (author)

75 FR 75453 - Proposed Information Collection; Comment Request; Technical Data Letter of Explanation

Science.gov (United States)

2010-12-03

... Request; Technical Data Letter of Explanation AGENCY: Bureau of Industry and Security. ACTION: Notice....gov . SUPPLEMENTARY INFORMATION: I. Abstract These technical data letters of explanation will assure the Bureau of Industry and Security that U.S.-origin technical data will be exported only for...

Information Retrieval Diary of an Expert Technical Translator.

Science.gov (United States)

Cremmins, Edward T.

1984-01-01

Recommends use of entries from the information retrieval diary of Ted Crump, expert technical translator at the National Institute of Health, in the construction of computer models showing how expert translators solve problems of ambiguity in language. Expert and inexpert translation systems, eponyms, abbreviations, and alphabetic solutions are…

Federal Technical Information and U.S. Competitiveness: Needs, Opportunities, and Issues.

Science.gov (United States)

Hill, Christopher T.

1989-01-01

Discusses the importance of competitiveness to the American economy and examines three areas where federal information policies affect American competitiveness: providing the private sector with technical information; making federal information resources available to industry; and restricting foreign access to those resources. For each area,…

Strategy for the future use and disposition of uranium-233: Technical information

International Nuclear Information System (INIS)

Bereolos, P.J.; Forsberg, C.W.; Kocher, D.C.; Krichinsky, A.M.

1998-04-01

This document provides a summary of technical information on the synthetic radioisotope 233 U. It is one of a series of four reports that map out a national strategy for the future use and disposition of 233 U. The technical information on 233 U in this document falls into two main areas. First, material characteristics are presented along with the contrasts of 233 U to the more well known strategic fissile materials, 235 U and plutonium (Pu). Second, information derived from the scientific information, such as safeguards, waste classifications, material form, and packaging, is presented. Throughout, the effects of isotopically diluting 233 U with nonfissile, depleted uranium (DU) are examined

Columbia River Coordinated Information System (CIS); Information Needs, 1992 Technical Report.

Energy Technology Data Exchange (ETDEWEB)

Petrosky, Charlie (Idaho Department of Fish and Game, Boise, ID); Kinney, William J. (Washington Department of Fishereis, Olympia, WA); Rowe, Mike (Shoshone-Bannock Tribes, Fort Hall, ID)

1993-05-01

Successful application of adaptive management to rebuilding the Columbia Basin`s anadromous fish resources requires that available information and experience be organized and shared between numerous organizations and individuals. Much of this knowledge exists only in unpublished form in agency and individual files. Even that information which is published in the form of technical and contract reports receives only limited distribution and is often out of print and unavailable after a few years. Only a small fraction of the basin`s collective knowledge is captured in permanent and readily available databases and recognized journals. State, tribal, and federal fishery managers have recognize these information management problems and have committed to a program, the Coordinated Information System Project, to capture and share more easily the core data and other information upon which management decisions are based. That project is now completing the process of scoping and identification of information needs. Construction of prototype systems will begin in 1992. This report is one in a series of seven describing the results of the Coordinated Information on System scoping and needs identification phase.

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Science.gov (United States)

2010-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis... 10 Energy 2 2010-01-01 2010-01-01 false Contents of applications; technical information in final safety analysis report. 52.157 Section 52.157 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSES...

10 CFR 52.79 - Contents of applications; technical information in final safety analysis report.

Science.gov (United States)

2010-01-01

...; technical information in final safety analysis report. (a) The application must contain a final safety... 10 Energy 2 2010-01-01 2010-01-01 false Contents of applications; technical information in final safety analysis report. 52.79 Section 52.79 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) LICENSES...

Technical methods for a risk-informed, performance-based fire protection program at nuclear power plants

International Nuclear Information System (INIS)

Dey, M.K.

1998-01-01

This paper presents a technical review and examination of technical methods that are available for developing a risk-informed, performance-based fire protection program at a nuclear plant. The technical methods include ''engineering tools'' for examining the fire dynamics of fire protection problems, reliability techniques for establishing an optimal fire protection surveillance program, fire computer codes for analyzing important fire protection safety parameters, and risk-informed approaches that can range from drawing qualitative insights from risk information to quantifying the risk impact of alternative fire protection approaches. Based on this technical review and examination, it is concluded that methods for modeling fires, and reliability and fire PRA analyses are currently available to support the initial implementation of simple risk-informed, performance-based approaches in fire protection programs. (author)

Technical methods for a risk-informed, performance-based fire protection program at nuclear power plants

International Nuclear Information System (INIS)

Dey, M.K.

2000-01-01

This paper presents a technical review and examination of technical methods that are available for developing a risk-informed, performance-based fire protection program at a nuclear plant. The technical methods include 'engineering tools' for examining the fire dynamics of fire protection problems, reliability techniques for establishing an optimal fire protection surveillance program, fire computer codes for analyzing important fire protection safety parameters, and risk-informed approaches that can range from drawing qualitative insights from risk information to quantifying the risk impact of alternative fire protection approaches. Based on this technical review and examination, it is concluded that methods for modeling fires, and reliability and fire probabilistic risk analyses (PRA) are currently available to support the initial implementation of simple risk-informed, performance-based approaches in fire protection programs. (orig.) [de

A Qualitative Content Analysis of Information Dissemination during the Consolidation of Two Technical Colleges

Science.gov (United States)

Drinnon, Charles

2017-01-01

This research examined the ways and means administration used to disseminate information concerning the consolidation of two technical colleges in the State of Georgia, USA. These means of information dissemination included press releases by the consolidating colleges and the Technical College System of Georgia (the system which the consolidating…

34 CFR 86.302 - What are the procedures used by the Secretary for providing information or technical assistance?

Science.gov (United States)

2010-07-01

... providing information or technical assistance? 86.302 Section 86.302 Education Office of the Secretary... information or technical assistance? (a) The Secretary provides information or technical assistance to an IHE in writing, through site visits, or by other means. (b) The IHE shall inform the Secretary of any...

Hydrogen Technical Analysis -- Dissemination of Information

Energy Technology Data Exchange (ETDEWEB)

George Kervitsky, Jr.

2006-03-20

SENTECH is a small energy and environmental consulting firm providing technical, analytical, and communications solutions to technology management issues. The activities proposed by SENTECH focused on gathering and developing communications materials and information, and various dissemination activities to present the benefits of hydrogen energy to a broad audience while at the same time establishing permanent communications channels to enable continued two-way dialog with these audiences in future years. Effective communications and information dissemination is critical to the acceptance of new technology. Hydrogen technologies face the additional challenge of safety preconceptions formed primarily as a result of the crash of the Hindenburg. Effective communications play a key role in all aspects of human interaction, and will help to overcome the perceptual barriers, whether of safety, economics, or benefits. As originally proposed SENTECH identified three distinct information dissemination activities to address three distinct but important audiences; these formed the basis for the task structure used in phases 1 and 2. The tasks were: (1) Print information--Brochures that target the certain segment of the population and will be distributed via relevant technical conferences and traditional distribution channels. (2) Face-to-face meetings--With industries identified to have a stake in hydrogen energy. The three industry audiences are architect/engineering firms, renewable energy firms, and energy companies that have not made a commitment to hydrogen (3) Educational Forums--The final audience is students--the future engineers, technicians, and energy consumers. SENTECH will expand on its previous educational work in this area. The communications activities proposed by SENTECH and completed as a result of this cooperative agreement was designed to compliment the research and development work funded by the DOE by presenting the technical achievements and validations

A review and evaluation of the Langley Research Center's Scientific and Technical Information Program: Results of phase 6: The technical report. A survey and analysis

Science.gov (United States)

Mccullough, R. A.; Pinelli, T. E.; Pilley, D. D.; Stohrer, F. F.

1982-01-01

Current practice and usage using selected technical reports; literature relative to the sequential, language, and presentation components of technical reports; and NASA technical report publications standards are discussed. The effctiveness of the technical report as a product for information dissemination is considered.

The socio-technical design of a library and information science collaboratory

DEFF Research Database (Denmark)

Lassi, Monica; Sonnenwald, Diane H.

2013-01-01

Introduction. We present a prototype collaboratory, a socio-technical platform to support sharing research data collection instruments in library and information science. No previous collaboratory has attempted to facilitate sharing digital research data collection instruments among library...... and information science researchers.  Method. We have taken a socio-technical approach to design, which includes a review of previous research on collaboratories; an empirical study of specific needs of library and information science researchers; and a use case design method to design the prototype collaboratory....... Scenarios of future interactions, use cases, were developed using an analytically-driven approach to scenario design. The use cases guided the implementation of the prototype collaboratory in the MediaWiki software package.  Results. The prototype collaboratory design is presented as seven use cases, which...

Scientific and technical information output of the Langley Research Center for calendar year 1984

Science.gov (United States)

1985-01-01

The scientific and technical information that the Langley Research Center produced during the calendar year 1984 is compiled. Approximately 1650 citations are included comprising formal reports, quick-release technical memorandums, contractor reports, journal articles and other publications, meeting presentations, technical talks, computer programs, tech briefs, and patents.

Important functions and development ideas of the library and information work in scientific and technical research institutes

International Nuclear Information System (INIS)

Ye Qingsen

2010-01-01

The library and information branch is an important constituent part of a scientific and technic research institute, and is a technically assistant department which is set for scientific and technic research and production. The investigations show that the achievements by the library and information departments are marked in scientific and technic research institutes, and the library and information works play important roles for the existence, development and innovation of the institute in past years. But, the present conditions and statuses are dropped behind, and more problems existed in the library and information departments as a whole. The development ideas are proposed for the library and information work by analyzing the characteristics of nowadays knowledge service, knowledge economy and network information time. (authors)

The Socio-Technical Design of a Library and Information Science Collaboratory

Science.gov (United States)

Lassi, Monica; Sonnenwald, Diane H.

2013-01-01

Introduction: We present a prototype collaboratory, a socio-technical platform to support sharing research data collection instruments in library and information science. No previous collaboratory has attempted to facilitate sharing digital research data collection instruments among library and information science researchers. Method: We have…

Development of a Centralized Automated Scientific and Technical Information Service in the People's Republic of Bulgaria.

Science.gov (United States)

Kiratsov, P.

1983-01-01

Discusses the design and organization of the Automated Information Centre, a centralized automated scientific and technical information service established within the main organ of Bulgaria's National System for Scientific and Technical Information, with UNESCO and United Nations Development Program assistance. Problems and perspectives for…

Scientific and technical information output of the Langley Research Center for Calendar Year 1985

Science.gov (United States)

1986-01-01

A compilation of the scientific and technical information that the Langley Research Center has produced during the calendar year 1985 is presented. Included are citations for Formal Reports, Quick-Release Technical Memorandums, Contractor Reports, Journal Articles and Other Publications, Meeting Presentations, Technical Talks, Computer Programs, Tech Briefs, and Patents.

Socio-technical Issues for Ubiquitous Information Society in 2010

Science.gov (United States)

Funabashi, Motohisa; Homma, Koichi; Sasaki, Toshiro; Sato, Yoshinori; Kido, Kunihiko; Fukumoto, Takashi; Yano, Koujin

Impact of the ubiquitous information technology on our society is so significant that directing technological development and preparing institutional apparatus are quite important and urgent. The present paper elaborates, with the efforts by both humanity and engineering disciplines, to find out the socio-technical issues of ubiquitous information society in 2010 by inspecting social implications of emerging technology as well as social expectations. In order to deliberate the issues, scenarios are developed that describes possible life in ubiquitous information society. The derived issues cover integrating information technology and human body, producing smart sharable environment, protecting individual rights, fostering new service business, and forming community.

AHMCT Intelligent Roadway Information System (IRIS) technical support and testing

Science.gov (United States)

2011-12-31

This report documents the research project AHMCT IRIS Technical Support and Testing, : performed under contract 65A0275, Task ID 1777. It presents an overview of the Intelligent : Roadway Information System (IRIS), and its design and function. ...

TMI-2 Technical Information and Examination Program. 1984 annual report

International Nuclear Information System (INIS)

Hess, C.J.

1985-04-01

In 1984, the US Department of Energy's Technical Information and Examination Program entered its fifth year of research and development work at Three Mile Island Unit 2 (TMI-2) and at the Idaho National Engineering Laboratory and other supporting laboratories. The work concentrated on six major areas: waste immobilization, reactor evaluation, data acquisition, information and industry coordination, core activities, and EPICOR II and waste research and disposition

Scientific and technical information as a source for IAEA safeguards state evaluation

Energy Technology Data Exchange (ETDEWEB)

Barletta, M.; Feldman, Y.; Ferguson, M. [International Atomic Energy Agency, Vienna (Austria)

2014-07-01

The IAEA Department of Safeguards is continually working to refine its methodologies and procedures for the analysis of information relevant to the evaluation of the nuclear fuel cycle in States that have safeguards agreements with the IAEA. This analysis is required to achieve an understanding of States' nuclear-related activities against which a State's declarations are evaluated for correctness as well as completeness, and to provide credible assurances on the peaceful uses of nuclear material in the State. To achieve this end, diversification of sources and comparison for consistency among available information is essential to ensure an accurate assessment of a State's nuclear activities. Open sources of information on scientific and technical (S&T) developments and research provide the Department of Safeguards with an enhanced basis to evaluate the technical capabilities of States. These information sources are regularly and systematically assessed to provide information about industrial capabilities, patenting activities and research and development activities in States as reflected through published scientific and technical literature. Using such sources, in addition to other, long-established safeguards information sources, helps the IAEA to draw soundly-based safeguards conclusions. The utility of this category of information in terms of the State evaluation process lies primarily in the comparison with other sources of information, especially State-declared information, and in the assessment of consistency of all safeguards-relevant information regarding nuclear fuel cycle technologies and activities in a State. The current paper aims to describe the use of S&T literature, how information from different sources is consolidated, how it is analysed and how it contributes in the overall process of State evaluation in the IAEA Department of Safeguards. (author)

Automating the Technical Library at Los Angeles' Department of Information Systems.

Science.gov (United States)

Gillette, Robert

1992-01-01

Description of the automation of the technical library of the City of Los Angeles Department of Information Services provides background information on the department and its library; lists the automation project goals and objectives; and describes the two software programs--ObjectVision and Paradox Engine--used as applications development tools…

Effectiveness of TIC [Technical Information Center] categories compared for disseminating research and developing reports

International Nuclear Information System (INIS)

Vaden, W.M.

1983-09-01

To carry out programs whereby these responsibilities may be fully implemented, different modes of information dissemination have been established or approved by the Center on behalf of its varied and vast user audiences. The differing requirements relating to disseminating information have their origins in DOE's statutory authorities embodied principally in (1) CFR 10, Sec. 795 on the control of information (Restricted Data) and (2) 42 USC 7151 (A) that requires ''dissemination of scientific and technical information ... to provide that free interchange of ideas and criticism which is essential to scientific and industrial progress and public undertaking and to enlarge the fund of technical information.''

Comparing the Scale of Web Subject Directories Precision in Technical-Engineering Information Retrieval

Directory of Open Access Journals (Sweden)

Mehrdokht Wazirpour Keshmiri

2012-07-01

Full Text Available The main purpose of this research was to compare the scale of web subject directories precision in information retrieval of technical-engineering science. Information gathering was documentary and webometric. Keywords of technical-engineering science were chosen at twenty different subjects from IEEE (Institute of Electrical and Electronics Engineers and engineering magazines that situated in sciencedirect site. These keywords are used at five subject directories Yahoo, Google, Infomine, Intute, Dmoz, that were web directories high-utilization. Usually first results in searching tools are connected to searching keywords. Because, first ten results was evaluated in every search. These assessments to consist of scale of precision, scale of error, scale retrieval items in technical-engineering categories to retrieval items entirely. The used criteria for determining the scale of precision that was according to high-utilization standards in different documents, to consist of presence of the keywords in title, appearance of keywords at the part of web retrieved pages, keywords adjacency, URL of page, page description and subject categories. Information analysis was according to Kruskal-Wallis Test and L.S.D fisher. Results revealed that there was meaningful difference about precision of web subject directories in information retrieval of technical-engineering science, Therefore this theory was confirmed.web subject directories ranked from point of precision as follows. Google, Yahoo, Intute, Dmoz, and Infomine. The scale of observed error at the first results was another criterion that was used for comparing web subject directories. In this research, Yahoo had minimum scale of error and Infomine had most of error. This research also compared the scale of retrieval items in all of categories web subject directories entirely to retrieval items in technical-engineering categories, results revealed that there was meaningful difference between them. And

Geothermal Energy and the Eastern US: Technical Information Interchange Meeting, Minutes

Energy Technology Data Exchange (ETDEWEB)

None

1979-12-01

The technical interchange meeting documented here is the fourth meeting where people interested in geothermal energy in the Eastern US have met to interchange technical information. These meetings are intended to assist all in the difficult task of balancing time and effort in doing their assigned jobs and keeping track of what others are doing in similar or related tasks. All of the aforementioned meetings have served their intended purpose and further regional and national meetings are sure to follow.

Prospect of Ti-Ni shape memory alloy applied in reactor structures

International Nuclear Information System (INIS)

Duan Yuangang

1995-01-01

Shape memory effect mechanism, physical property, composition, manufacturing process and application in mechanical structure of Ti-Ni shape memory alloy are introduced. Applications of Ti-Ni shape memory alloy in reactor structure are prospected and some necessary technical conditions of shape memory alloy applied in the reactor structure are put forward initially

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 22: US academic librarians and technical information specialists as information intermediaries: Results of the phase 3 survey

Science.gov (United States)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis U.S. academic librarians and technical information specialists as information intermediaries.

The Technical Report: An Analysis of Information Design and Packaging for an Inelastic Market.

Science.gov (United States)

Pinelli, Thomas E.; And Others

As part of an evaluation of its scientific and technical information program, the National Aeronautics and Space Administration (NASA) conducted a review and analysis of structural, language, and presentation components of its technical report form. The investigation involved comparing and contrasting NASA's publications standards for technical…

Informing the public on technical effectiveness of international safeguards

International Nuclear Information System (INIS)

Hunt, H.M.

1994-01-01

In recent years, public interest regarding IAEA (International Atomic Energy Agency) safeguards effectiveness has partially shifted to detection of undeclared nuclear facilities. Nevertheless, important segments of the public remain vitally interested in whether international safeguards would be able to reliably and definitively detect diversion of bomb quantities of plutonium or highly enriched uranium from open-quotes bulk handlingclose quotes facilities. There now exists a sizable body of unclassified technical reports, based on experimental results over many years, written by various experts, describing actual capabilities and limitations of safeguards techniques and systems, which collectively lead to definitive evaluations of technical safeguards effectiveness. For a large-scale operation of spent fuel reprocessing, plutonium fuel fabrication, or gas centrifuge uranium enrichment, an undisputable conclusion is that international safeguards systems would be unable to reliably and definitively detect the diversion in a one-year period of a significant quantity of plutonium or enriched uranium; moreover, diversion of many significant quantities per year (from such an operation) would have negligible probability of definitive detection if conducted in accordance with particle diversion scenarios. To properly inform the public and government agencies, reports on technical effectiveness of international safeguards should incorporate these basic conclusions

Coating power RF components with TiN

International Nuclear Information System (INIS)

Kuchnir, M.; Hahn, E.

1995-03-01

A facility for coating RF power components with thin films of Ti and/or TiN has been in operation for some time at Fermilab supporting the Accelerator Division RF development work and the TESLA program. It has been experimentally verified that such coatings improve the performance of these components as far as withstanding higher electric fields. This is attributed to a reduction in the secondary electron emission coefficient of the surfaces when coated with a thin film containing titanium. The purpose of this Technical Memorandum is to describe the facility and the procedure used

Deformation mechanisms in Ti/TiN multilayer under compressive loading

International Nuclear Information System (INIS)

Yang, Wei; Ayoub, Georges; Salehinia, Iman; Mansoor, Bilal; Zbib, Hussein

2017-01-01

The promising mechanical, physical and chemical properties of nano-scale metal/ceramic multilayers (MCMs) are of high interest for extreme environment applications. Understanding the plastic deformation mechanisms and the variables affecting those properties is therefore essential. The interface characteristics and the plastic deformation mechanisms under compressive loading in a Ti/TiN multilayer with a semi-coherent interface are numerically investigated. The interface structure of the Ti/TiN interface and the interface misfit dislocation were characterized using molecular dynamic simulations combined with atomically informed Frank-Bilby method. Three possible atomic stacking interface structures are identified according to the crystallographic analysis of the interface. Upon relaxation, large interface areas are occupied with the energetically stable configuration. Furthermore, the higher energy stacking are transformed into misfit dislocations or dislocation nodes. The molecular dynamic compressive stress strain response of the Ti/TiN multilayers exhibited three distinctive peaks. The first peak was generated by the dislocation dissociation of perfect dislocation into pairs of partials dislocation around extended nodes region at the interface. Upon further compression the second peak, identified as the first yielding, resulted from the activation of pyramidal slip planes in the Ti layer. Finally, a third peak identified as the second yielding, occurred when dislocation nucleated/transmitted in/into the TiN layer.

The Story of the Defense Technical Information Center 1945 - 1995, 50 Years of Information for Defense

Science.gov (United States)

1995-07-01

necessary. As John Naisbitt observed in his 1982 book Megatrends , ...with the coming of the infor- mation society, we have for the first time an economy...information in the hands of many. —John Naisbitt Megatrends As the Defense Technical Information Center moves forward into the last decade of the...Gulf War, for example, Iraq’s leader, Saddam Hussein, threatened to use biological or biochemical warfare. To defend against this threat, the U.S

Scientific and technical information output of the Langley Research Center for calendar year 1980

Science.gov (United States)

1981-01-01

This document is a compilation of the scientific and technical information that the Langley Research Center has produced during the calendar year 1980. Approximately 1400 citations are given. Formal reports, quick-release technical memorandums, contractor reports, journal articles, meeting/conference papers, computer programs, tech briefs, patents, and unpublished research are included.

Scientific and technical information output of the Langley Research Center for calendar year 1986

Science.gov (United States)

1987-01-01

This document is a compilation of the scientific and technical information that the Langley Research Center has produced during the calendar year 1986. Included are citations for Formal Reports, Quick-Release Technical Memorandums, Contractor Reports, Journal Articles and Other Publications, Meeting Presentations, Techncial Talks, Computer Programs, Tech Briefs, and Patents.

Geothermal Energy and the Eastern US: Fifth technical information interchange meeting, Minutes

Energy Technology Data Exchange (ETDEWEB)

None

1980-12-01

The technical interchange meeting documented here is the fifth meeting where people interested in geothermal energy in the Eastern US have met to interchange technical information. These meetings are intended to assist all in the difficult task of balancing time and effort in doing their assigned jobs and keeping track of what others are doing in similar or related tasks. All of the aforementioned meetings have served their intended purpose and further regional and national meetings are sure to follow.

78 FR 52963 - 60-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Science.gov (United States)

2013-08-27

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY...: HUD is seeking approval from the Office of Management and Budget (OMB) for the information collection... interested parties on the proposed collection of information. The purpose of this notice is to allow for 60...

Sandia Laboratories technical capabilities. Auxiliary capabilities: environmental health information science

International Nuclear Information System (INIS)

1975-09-01

Sandia Laboratories is an engineering laboratory in which research, development, testing, and evaluation capabilities are integrated by program management for the generation of advanced designs. In fulfilling its primary responsibility to ERDA, Sandia Laboratories has acquired extensive research and development capabilities. The purpose of this series of documents is to catalog the many technical capabilities of the Laboratories. After the listing of capabilities, supporting information is provided in the form of highlights, which show applications. This document deals with auxiliary capabilities, in particular, environmental health and information science. (11 figures, 1 table) (RWR)

Technical specifications review of nuclear power plants: a risk-informed evaluation

International Nuclear Information System (INIS)

Saldanha, Pedro Luiz da Cruz; Sousa, Anna Leticia; Frutuoso e Melo, Paulo Fernando Ferreira; Duarte, Juliana Pacheco

2012-01-01

The use of risk information by a regulatory body as part of an integrated decision making process addresses the way in which risk information is being used as part of an integrated process in making decisions about safety issues at nuclear plants – commonly referred to as risk-informed decision making. The risk-informed approach aims to integrate in a systematic manner quantitative and qualitative, deterministic and probabilistic safety considerations to obtain a balanced decision. Probabilistic Safety Assessment (PSA) is a methodology that can be applied to provide a structured analysis process to evaluate the frequency and consequences of accidents scenarios in nuclear power plants. Technical Specifications (TS) are specifications regarding the characteristics of nuclear power plants (variables, systems or components) of overriding importance to nuclear safety and radiation protection, which is an integral part of plant operation authorization. Limiting Conditions of Operation (LCO) are the minimum levels of performance or capacity or operating system components required for the safe operation of nuclear plants, as defined in technical specifications. The Maintenance Rule (MR) is a requirement established by the U. S. Nuclear Regulatory Commission (NRC) to check the effectiveness of maintenance carried out in nuclear plants, and plant configuration control. The control of plant configuration is necessary to verify the impact of the maintenance of a safety device out of service on plant safety. The Electric Power Research Institute (EPRI) has assessed the role of probabilistic safety analysis in the regulation of nuclear power plants with the following objectives: a) to provide utilities with an approach for developing and implementing nuclear power station risk-managed technical specification programs; and b) to complement and supplement existing successful configuration risk management applications such as MR. This paper focuses on the evaluation of EPRI

NASA/DOD Aerospace Knowledge Diffusion Research Project. Report number 21: US aerospace industry librarians and technical information specialists as information intermediaries: Results of the phase 2 survey

Science.gov (United States)

Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1994-01-01

The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DoD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis U.S. aerospace industry librarians and technical information specialists as information intermediaries.

Technical Support and Transfer of Geothrmal Technical Knowledge and Information

Energy Technology Data Exchange (ETDEWEB)

John W. Lund; Toni" Boyd

2007-11-14

The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

SUSTAINING OCCUPATIONAL INFORMATION FOR CAREER CHOICE AND DEVELOPMENT IN STUDENTS OF TECHNICAL COLLEGES IN ENUGU STATE, NIGERIA

OpenAIRE

Moses Ikebe Odo

2015-01-01

This study takes on the issue of sustaining occupational information for career choice and development in students of technical colleges in Enugu State, Nigeria. The method adopted for this study was the survey design and the population included were all final year students of the three government technical colleges in Enugu State of Nigeria. The technical colleges were sampled as follows: Government Technical College, Enugu (156 students); Government Technical College, Nsukka (148 students);...

Report on the basic design of the FY 1998 technical information database; 1998 nendo gijutsu joho database no kihon sekkei hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting the effective transfer of the results of technical development and the technical information distribution, study and basic design were conducted of a concept of the new technical database run by NEDO. In the study, the following were conducted to extract the subjects: analysis of examples of project databases such as CADDET, scientific technology research information (JCLEARING), evaluation/survey of the present situation of database users, etc. In the study of a concept of technical information database, clarified were the classification of information, definition of the details, finding-out of relations between various kinds of information, mechanism of collection/processing/storage/dispatch/exchange of information, role of NEDO, etc. In the basic design, as the NEDO technical information database viable for the moment, the rough design was conducted of the project information, information on result reports, and information on research institutes. Further, to handle in unity the database controlled in different method, studied were the applicability to the project database of the general combined concept, advantages, restricted items, etc. (NEDO)

Integrating research, legal technical assistance, and advocacy to inform shared use legislation in Mississippi.

Science.gov (United States)

Spengler, John O; Frost, Natasha R; Bryant, Katherine K

2014-01-01

The purpose of this article was to describe the process by which research findings informed the successful passage of legislation designed to increase opportunities for physical activity in Mississippi, and discuss implications and lessons learned from this process. The article is descriptive and conceptual, and addresses the collaborative process by which research, legal technical assistance, and advocacy informed and shaped shared use legislation in Mississippi. Collaborators informing this article were an Active Living Research grantee, a staff attorney with the Public Health Law Center, the American Heart Association Mississippi Government Relations Director, and community partners. The American Heart Association and Public Health Law Center developed policy guidance in the form of sample language for legislation as a starting point for states in determining policy needed to eliminate or reduce barriers to the shared use of school recreational facilities. The policy guidance was informed by evidence from Active Living Research-funded research studies. The American Heart Association, supporting a bill shaped by the policy guidance, led the effort to advocate for successful shared use legislation in Mississippi. Research should be policy relevant and properly translated and disseminated. Legal technical assistance should involve collaboration with both researchers and advocates so that policymakers have the information to make evidence-based decisions. Government relations directors should collaborate with legal technical staff to obtain and understand policy guidance relevant to their advocacy efforts. Effective collaborations, with an evidence-based approach, can lead to informed, successful policy change.

Ensuring the conflict sustainability of the information systems on the basis of technical means

Directory of Open Access Journals (Sweden)

L. E. Mistrov

2016-01-01

Full Text Available The analysis of the purposes, tasks, functions and ways of ensuring conflict stability of func-tioning of information systems on the ba-sis of application of a complex of technical means is carried out. The main contours of management of elements of the organizational and technical systems (OTS in various forms of actions are defined. It is noted that a basis of functioning of OTS, infor-mation sup-port makes, classes of the data making him are defined. It is shown that ensuring conflict stability of functioning of the information sys-tems (IS is carried out by the complex of technical means (CTM, as a part of subsystems of reception / transfer, collecting and de-struction / distortion of information, their main functions are defined. Wednesday in which KTS function, is defined as an information and target situation which is understood as the part of a social and economic situa-tion characterized by existence of KTS providing functioning with IS, their location, operating modes, parameters of the information streams (IS, characteristics of technical means of processing, storage, submission of information realized by ways of the information security (IS for the solution of tasks in dynamics of information conflict. At the same time the information conflict is part target (the difficult conflict OTS representing information ex-change of KTS providing conflict steady functioning of IS at realization of processes of collection of information, transfer and counter-action to carrying out similar actions by the competing party with means of the destroying / distorting in-fluences (RIV. The special at-tention is paid to research of actions of a subsystem of collection of information, methods of collection of information are defined, con-ditions of application of methods of processing of the collected data are shown, features of functioning of subsystems of KTS at vari-ous stages of application are considered. The conclusion is drawn that

PIIID-formed (Ti, O)/Ti, (Ti, N)/Ti and (Ti, O, N)/Ti coatings on NiTi shape memory alloy for medical applications

Energy Technology Data Exchange (ETDEWEB)

Sun Tao, E-mail: taosun@hotmail.com.hk [Department of Mechanical Engineering, University of Hong Kong, Pokfulam Road (Hong Kong); Institute of Microelectronics, Agency for Science, Technology and Research (A-STAR) (Singapore); Wang Langping, E-mail: aplpwang@hit.edu.cn [State Key Lab of Advanced Welding and Joining, Harbin Institute of Technology (China); Wang Min; Tong Howang [Department of Mechanical Engineering, University of Hong Kong, Pokfulam Road (Hong Kong); Lu, William W. [Department of Orthopedics and Traumatology, University of Hong Kong, Sassoon Road (Hong Kong)

2012-08-01

(Ti, O)/Ti, (Ti, N)/Ti and (Ti, O, N)/Ti composite coatings were fabricated on NiTi shape memory alloy via plasma immersion ion implantation and deposition (PIIID). Surface morphology of samples was investigated using atomic force microscopy (AFM) and scanning electron microscopy (SEM). Cross-sectional morphology indicated that the PIIID-formed coatings were dense and uniform. X-ray diffraction (XRD) was used to characterize the phase composition of samples. X-ray photoelectron spectroscopy (XPS) results showed that the surface of coated NiTi SMA samples was Ni-free. Nanoindentation measurements and pin-on-disc tests were carried out to evaluate mechanical properties and wear resistance of coated NiTi SMA, respectively. For the in vitro biological assessment of the composite coatings in terms of cell morphology and cell viability, osteoblast-like SaOS-2 cells and breast cancer MCF-7 cells were cultured on NiTi SMA samples, respectively. SaOS-2 cells attached and spread better on coated NiTi SMA. Viability of MCF-7 cells showed that the PIIID-formed composite coatings were noncytotoxic and coated samples were more biocompatible than uncoated samples. - Highlights: Black-Right-Pointing-Pointer PIIID-formed coatings were fabricated on NiTi SMA to improve its biocompatibility. Black-Right-Pointing-Pointer Microstructure, mechanical properties and biocompatibility of coatings were investigated. Black-Right-Pointing-Pointer All PIIID-formed composite coatings were noncytotoxic and cytocompatible.

Development of technical information basis of aging management for nuclear power plants

International Nuclear Information System (INIS)

Kanno, M.

2007-01-01

In order to implement effective safety regulations on aging management for reactor facilities etc., the information on important technology issues, the latest technical knowledge including evaluation technology, test and research outcomes, related codes and standards, regulation information, operation experiences such as accidents and trouble, etc. with respect to aging-induced deterioration in and outside Japan and in other industries, were collected, organized and evaluated. (author)

Information Design: A New Approach to Teaching Technical Writing Service Courses

Science.gov (United States)

McKee, Candie DeLane

2012-01-01

This study used a needs assessment, process analysis, process design, and textbook design to develop a new process and new textbook, based on Cargile-Cook's layered literacies, Quesenbery's five qualities of usability, and Carliner's information design theories, for use in technical writing service learning courses. The needs assessment was based…

Technical Progress and Development Directions of Oceanic Spatial Information Datum

Directory of Open Access Journals (Sweden)

BAO Jingyang

2017-10-01

Full Text Available This paper briefly analyzes the basic development and technical situation of oceanic spatial information datum, reviews the main processes of oceanic vertical datum and correlative oceanic tidal study, such as improvement and perfect methods of determining tidal station vertical datum, realizing form of vertical datum controlled by tidal station, effect on maintaining vertical datum by long-term tidal station, oceanic tidal model establishing, and also construction and transformation of tidal datum, and then forecasts the key development directions of oceanic spatial information datum on high-accuracy marine position service, vertical datum and the transferring model refinement and spatial datum application.

A DDC Bibliography on Cost/Benefits of Technical Information Services and Technology Transfer.

Science.gov (United States)

Defense Documentation Center, Alexandria, VA.

This bibliography is a compilation of literature existing in both the government and public sectors and concerning Cost/Benefits of Technical information Services and Technology Transfer. Not only was the cost-benefit to the user reflected, but consideration was given to the initial cost of information collections, the cost of processing the…

A review of the information required by technical justifications and its availability

International Nuclear Information System (INIS)

Worrall, G.M.; Conroy, P.J.; Whittle, M.J.; Roscoe, P.

1997-03-01

A central feature of the European approach to Inspection Qualification (IQ) is the use of Technical Justifications (TJ). This arises from the recognition that practical trials of an inspection can never, by themselves, generate sufficient information to provide confidence in an inspection. The central role of TJ has raised concerns that information which is vital to their production may currently not be available. The range of roles that TJ can play in IQ is described in this report, their typical structure, the key input information, and the essential variables defined. The extent to which this information currently is available is then discussed. Information needs are defined. 10 refs

Safety Requirements and Modern Technical Requirements in Human Information Systems in Amman Hotels

OpenAIRE

Farouq Ahmad Alazzam; Sattam Rakan Allahawiah; Mohammad Nayef Alsarayreh; Kafa Hmoud Abdallah al Nawaiseh

2015-01-01

This study aimed to demonstrate the availability of Safety requirements and modern technical requirements in human information systems in Amman hotels. an the most important results of this study is the availability of security and safety requirements in human information systems In Amman hotels and The adequacy of the information that it provided .and show that all departments are not connected by appropriate and effective communication networks in adequate form . Also sophisticated operatin...

The Economic Value of Fundamental and Technical Information in Emerging Currency Markets

NARCIS (Netherlands)

G.J. de Zwart (Gerben); T.D. Markwat (Thijs); L.A.P. Swinkels (Laurens); D.J.C. van Dijk (Dick)

2007-01-01

textabstractWe measure the economic value of information derived from macroeconomic variables and from technical trading rules for emerging markets currency investments. Our analysis is based on a sample of 21 emerging markets with a floating exchange rate regime over the period 1997-2007 and

Aerial Measuring System Technical Integration Annual Report 2002

Energy Technology Data Exchange (ETDEWEB)

Bechtel Nevada Remote Sensing Laboratory

2003-06-01

Fiscal Year 2002 is the second year of a five-year commitment by the U.S. Department of Energy, National Nuclear Security Administration (NNSA) to invest in development of new and state-of-the-art technologies for the Aerial Measuring Systems (AMS) project. In 2000, NNSA committed to two million dollars for AMS Technical Integration (TI) for each of five years. The tragedy of September 11, 2001, profoundly influenced the program. NNSA redirected people and funding resources at the Remote Sensing Laboratory (RSL) to more immediate needs. Funds intended for AMS TI were redirected to NNSA's new posture of leaning further forward throughout. AMS TI was brought to a complete halt on December 10, 2001. Then on April 30, 2002, NNSA Headquarters allowed the restart of AMS TI at the reduced level of $840,000. The year's events resulted in a slow beginning of several projects, some of which were resumed only a few weeks before the AMS TI Symposium held at RSL on July 30.

The Relationship between Return on Profitability and Costs of Outsourcing Information Technology Technical Support

Science.gov (United States)

Odion, Segun

2011-01-01

The purpose of this quantitative correlational research study was to examine the relationship between costs of operation and total return on profitability of outsourcing information technology technical support in a two-year period of outsourcing operations. United States of America list of Fortune 1000 companies' chief information officers…

Sandia Transportation Technical Environmental Information Center and its application to transportation risk analyses

International Nuclear Information System (INIS)

Foley, J.T.; Davidson, C.A.; McClure, J.D.

1978-01-01

Purpose of this paper is to describe an applied research activity which is fundamental to the conduct of transportation analyses: the collection, analysis, storage, and retrieval of information on the intensities of technical environments. This paper describes the collection system which provides such a service to official researchers in transportation analysis and the applications of this information in the area of risk analysis

Development of the standard classification system of technical information in the field of RI-biomics and its application to the web system

International Nuclear Information System (INIS)

Jang, Sol Ah; Kim, Joo Yeon; Park, Tai Jin

2014-01-01

RI-Biomics is a new concept that combines radioisotopes (RI) and Biomics. For efficient collection of information, establishment of database for technical information system and its application to the system, there is an increasing need for constructing the standard classification system of technical information by its systematical classification. In this paper, we have summarized the development process of the standard classification system of technical information in the field of RI-Biomics and its application to the system. Constructing the draft version for the standard classification system of technical information was based on that standard classification one in national science and technology in Korea. The final classification system was then derived through the reconstruction and the feedback process based on the consultation from the 7 experts. These results were applied to the database of technical information system after transforming as standard code. Thus, the standard classification system were composed of 5 large classifications and 20 small classifications, and those classification are expected to establish the foundation of information system by achieving the circular structure of collection-analysis-application of information

A monitored retrievable storage facility: Technical background information

International Nuclear Information System (INIS)

1991-07-01

The US government is seeking a site for a monitored retrievable storage facility (MRS). Employing proven technologies used in this country and abroad, the MRS will be an integral part of the federal system for safe and permanent disposal of the nation's high-level radioactive wastes. The MRS will accept shipments of spent fuel from commercial nuclear power plants, temporarily store the spent fuel above ground, and stage shipments of it to a geologic repository for permanent disposal. The law authorizing the MRS provides an opportunity for a state or an Indian tribe to volunteer to host the MRS. The law establishes the Office of the Nuclear Waste Negotiator, who is to seek a state or an Indian tribe willing to host an MRS at a technically-qualified site on reasonable terms, and is to negotiate a proposed agreement specifying the terms and conditions under which the MRS would be developed and operated at that site. This agreement can ensure that the MRS is acceptable to -- and benefits -- the host community. The proposed agreement must be submitted to Congress and enacted into law to become effective. This technical background information presents an overview of various aspects of a monitored retrievable storage facility, including the process by which it will be developed

Summary of technical information and agreements from Nuclear Management and Resources Council industry reports addressing license renewal

International Nuclear Information System (INIS)

Regan, C.; Lee, S.

1996-10-01

In about 1990, the Nuclear Management and Resources Council (NUMARC) submitted for NRC review ten industry reports (IRs) addressing aging issues associated with specific structures and components of nuclear power plants ad one IR addressing the screening methodology for integrated plant assessment. The NRC staff had been reviewing the ten NUMARC IRs; their comments on each IR and NUMARC responses to the comments have been compiled as public documents. This report provides a brief summary of the technical information and NUMARC/NRC agreements from the ten IRs, except for the Cable License Renewal IR. The technical information and agreements documented herein represent the status of the NRC staffs review when the NRC staff and industry resources were redirected to address rule implementation issues. The NRC staff plans to incorporate appropriate technical information and agreements into the draft standard review plan for license renewal

Nanomechanical properties of TiCN and TiCN/Ti coatings on Ti prepared by Filtered Arc Deposition

International Nuclear Information System (INIS)

Sun, Yong; Lu, Cheng; Yu, Hailiang; Kiet Tieu, A.; Su, Lihong; Zhao, Yue; Zhu, Hongtao; Kong, Charlie

2015-01-01

Monolayer TiCN and multilayer TiCN/Ti coatings were deposited on the surface of Ti using the Filtered Arc Deposition System (FADS). Nanoindentation tests were performed on both coatings. The multilayer TiCN/Ti coating exhibited better ductility than the monolayer TiCN coating. The lattice constants of the coatings were characterized by X-ray diffraction. Transmission Electron Microscopy (TEM) was used to investigate the fracture behavior of the coatings. Inter-columnar, inclined and lateral cracks were found to be the dominant crack modes in the monolayer TiCN coatings while small bending crack and radial crack were the dominant crack modes in the multilayer TiCN/Ti coatings. The Finite Element Method (FEM) was used to simulate the indentation process. It was found that the Ti interlayer in the multilayer TiCN/Ti coating could efficiently suppress the fracture, which is responsible for the improved ductility of the multilayer TiCN/Ti coating

The Users and Uses of Scientific and Technical Information: Critical Research Needs.

Science.gov (United States)

Freeman, James E.; Rubenstein, Albert H.

At a 1973 workshop held in Denver, Colorado, 21 participants familiar with the uses of Scientific and Technical Information (STI) services gathered to identify the system's major research needs. Initially, 50 research projects were suggested in the areas of design, management, operations, marketing, and global considerations. Using a priority…

Technical-Oriented Enterprise Resource Planning (ERP) Body of Knowledge for Information Systems Programs: Content and Implementation

Science.gov (United States)

Boyle, Todd A.

2007-01-01

In this article, the author proposes a body of knowledge that the educators can use to incorporate the technical aspects of enterprise resource planning (ERP) into an information systems (IS) program, encapsulated as the ERP technical knowledge framework. To illustrate the application of this framework, the author discusses a course sequence that…

Integrating Information Services in an Academic Setting: The Organizational and Technical Challenge.

Science.gov (United States)

Branin, Joseph J.; And Others

1993-01-01

Describes a project to integrate the support and delivery of information services to faculty and staff at the University of Minnesota from the planning phase to implementation of a new organizational entity. Topics addressed include technical and organizational integration, control and delivery of services, and networking and organizational fit.…

European Community initiatives and experience in scientific and technical information

International Nuclear Information System (INIS)

Steven, G.

1990-05-01

Scientific and technical information (STI) is an increasingly important resource for R and D and industrial development. The rapid development of the market for electronic information and the increasing potential offered through new information technologies require new approaches for the collection and dissemination of STI. Activities of the Commission of the European Communities (CEC) in this area are reviewed. More recent CEC initiatives in the areas of biotechnology information and factual materials data banks have proved the need for international collaboration and for the implementation of infrastructural measures as a basis for such collaboration. The implementation of the EC Demonstrator Programme on materials property data systems has evaluated the potential of eleven European materials data banks against the market requirements and has helped to launch wide international collaboration. The concluding European workshop on materials data systems has developed a set of recommendations for future initiatives. These are shortly reviewed together with initial findings of a study aimed at developing a business plan for the establishment of a biotechnology information infrastructure for the bio-industries and research base in Europe. (author). 3 refs

European Community initiatives and experience in scientific and technical information

Energy Technology Data Exchange (ETDEWEB)

Steven, G [Commission of the European Communities, Luxembourg (Luxembourg)

1990-05-01

Scientific and technical information (STI) is an increasingly important resource for R and D and industrial development. The rapid development of the market for electronic information and the increasing potential offered through new information technologies require new approaches for the collection and dissemination of STI. Activities of the Commission of the European Communities (CEC) in this area are reviewed. More recent CEC initiatives in the areas of biotechnology information and factual materials data banks have proved the need for international collaboration and for the implementation of infrastructural measures as a basis for such collaboration. The implementation of the EC Demonstrator Programme on materials property data systems has evaluated the potential of eleven European materials data banks against the market requirements and has helped to launch wide international collaboration. The concluding European workshop on materials data systems has developed a set of recommendations for future initiatives. These are shortly reviewed together with initial findings of a study aimed at developing a business plan for the establishment of a biotechnology information infrastructure for the bio-industries and research base in Europe. (author). 3 refs.

Nevada Applied Ecology Information Center: a review of technical information support provided to the Nevada Applied Ecology Group

International Nuclear Information System (INIS)

Fore, C.S.; Pfuderer, H.A.

1983-01-01

The Nevada Applied Ecology Information Center (NAEIC) was established in January 1972 to serve the needs of the Nevada Applied Ecology Group (NAEG) by identifying, collecting, analyzing, and disseminating technical information relevant to NAEG programs. Since its inception, the NAEIC has been active in providing specialized information support to NAEG staff in the following research areas: (1) environmental aspects of the transuranics; (2) historic literature (pre-1962) on plutonium and uranium; (3) cleanup and treatment of radioactively contaminated land; (4) bioenvironmental aspects of europium and rhodium; (5) NAEG contractor reports; and (6) uptake of radioactivity by food crops

An architecture and methodology for the design and development of Technical Information Systems

NARCIS (Netherlands)

Capobianchi, R.; Mautref, M.; van Keulen, Maurice; Balsters, H.

In order to meet demands in the context of Technical Information Systems (TIS) pertaining to reliability, extensibility, maintainability, etc., we have developed an architectural framework with accompanying methodological guidelines for designing such systems. With the framework, we aim at complex

Practical Problems in Connection with the Planning and Introduction of Information Systems. Technical Report.

Science.gov (United States)

Klose, Traugott

Major reforms brought about in July 1969 at the Free University of Berlin in its organization, planning, and decision making are reviewed. Specific problems are addressed, such as plans for introducing an information system on technical data and space use, plans for an information system on personnel employed by the university, and plans for an…

Preparation of Al-Ti-B grain refiner by SHS technology

International Nuclear Information System (INIS)

Nikitin, V.I.; Wanqi, J.I.E.; Kandalova, E.G.; Makarenko, A.G.; Yong, L.

2000-01-01

Since the discovery of the grain refinement effect of aluminum by titanium, especially with the existence of B or C in 1950, grain refiners are widely accepted in industry for microstructure control of aluminum alloys. Research on this topic is to obtain the highest grain refinement efficiency with the lowest possible addition of master alloy. It is widely accepted that the morphology and size of TiAl 3 particles, which are known as heterogeneous nucleation centers, are important factors deterring the grain refinement efficiency. Fine TiAl 3 particles are favorable. The grain refinement process shows a heredity phenomenon, which means that structural information from initial materials transfers through a melt to the final product. It is important to find the connection between microstructural parameters of the master alloy and the final product. To improve the quality of Al-Ti-B master alloys for the use as a grain refiner, a new method based on SHS (self-propagating high-temperature synthesis) technology has been developed in Samara State Technical University to produce the master alloys. SHS, as a new method for preparation of materials, was first utilized by Merzhanov in 1967. This method uses the energy from highly exothermic reactions to sustain the chemical reaction in a combustion wave. The advantages of SHS include simplicity, low energy requirement, and higher product purity. Because SHS reactions can take place between elemental reactants, it is easy to control product composition. The purposes of this investigation were to fabricate an SHS Al-5%Ti-1%B master alloy, to analyze its structure and to test its grain refining performance

Expressive/Exploratory Technical Writing (XTW) in Engineering: Shifting the Technical Writing Curriculum

Science.gov (United States)

Warnock, Scott; Kahn, Michael

2007-01-01

While the importance of "expressive writing," or informal, self-directed writing, has been well established, teachers underutilize it, particularly in technical writing courses. We introduce the term expressive/exploratory technical writing (XTW), which is the use of informal, self-directed writing to problem-solve in technical fields. We describe…

Examining the Impact of Non-Technical Security Management Factors on Information Security Management in Health Informatics

Science.gov (United States)

Imam, Abbas H.

2013-01-01

Complexity of information security has become a major issue for organizations due to incessant threats to information assets. Healthcare organizations are particularly concerned with security owing to the inherent vulnerability of sensitive information assets in health informatics. While the non-technical security management elements have been at…

76 FR 323 - Information Systems Technical Advisory Committee; Notice of Partially Closed Meeting

Science.gov (United States)

2011-01-04

... Computing, Technology and Security Issues Thursday, January 27 Closed Session 8. Discussion of matters... DEPARTMENT OF COMMERCE Bureau of Industry and Security Information Systems Technical Advisory...), Building 33, Cloud Room, 53560 Hull Street, San Diego, California 92152. The Committee advises the Office...

Comparison of mechanical behavior of TiN, TiNC, CrN/TiNC, TiN/TiNC films on 9Cr18 steel by PVD

Science.gov (United States)

Feng, Xingguo; Zhang, Yanshuai; Hu, Hanjun; Zheng, Yugang; Zhang, Kaifeng; Zhou, Hui

2017-11-01

TiN, TiNC, CrN/TiNC and TiN/TiNC films were deposited on 9Cr18 steel using magnetron sputtering technique. The morphology, composition, chemical state and crystalline structure of the films were observed and analyzed by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Hardness and adhesion force were tested by nanoindentation and scratch tester, respectively. The friction and wear behavior of TiN, TiNC, CrN/TiNC and TiN/TiNC films sliding against GCr15 balls were investigated and compared synthetically using ball-on-disk tribometer. It was found that Tisbnd N, Tisbnd C, Tisbnd Nsbnd C and Csbnd C bonds were formed. The TiN/TiNC film was composed of TiN, TiC and TiNC phases. Hardness and adhesion force results indicated that although the TiN film possessed the highest hardness, its adhesion force was lowest among all the films. Tribological test results showed that the friction coefficient of TiN/TiNC was much lower than that of TiN and the wear rate decreases remarkably from 2.3 × 10-15 m3/Nm to 7.1 × 10-16 m3/Nm, which indicated the TiN/TiNC film has better wear resistance.

Establishing a scientific and technical information program: Planning and resource management

Science.gov (United States)

Blados, Walter R.

1992-01-01

In the last 50 years, technological advances have accelerated at a rate unprecedented in history. We are experiencing a tremendous expansion of scientific and technological effort in many directions, and the result is a fantastic increase in the accumulation of scientific and technical information (STI) and knowledge. An integral part of the research and development (R&D) process is the STI associated with it. STI is both a raw material (input) and a product (output) of this process. The topics addressed include the following: the value of STI, management of an STI program, program policy and guidance, organizational structure, data sources, training/orientation, and the current information environment.

Multicriterial optimization of preventive maintenance of informational/technical stochastic system

Directory of Open Access Journals (Sweden)

Kovalenko Anna

2016-01-01

Full Text Available The problem of optimization of reliability and economical indexes is solved for informational/technical system with periodical diagnostics and restoration. The system considered is the one with users accesses and errors occurring. The probability that the error occurs increases in time. Therefore, the longer is the restoration period the more there is a risk of system operation with error. But too frequent restoration can be too expensive. To take into account all these factors two-criteria optimization is made with the restriction of reliability characteristic being of the given level.

Technical Site Information: Planning group of the Directorate and Conventional Construction Division

International Nuclear Information System (INIS)

1993-11-01

This document presents the technical site information for the Superconducting Super Collider project. The Ellis County, Texas site was selected by the Department of Energy in 1989. After assembling the initial staff at temporary facilities in Dallas, the SSC Laboratory began site-specific design work. The resulting design for the SSC accelerators, experimental areas, and laboratory facilities were described in the Site-Specific Conceptual Design Report of July 1990. Since then, design specifications for the technical components and conventional facilities have been formulated. In fact, a very significant amount of surface and underground construction has been initiated and many buildings have been completed. Testing of prototypes for most technical components is advanced. The construction phase of the SSC project is approximately 20% complete. At this time, it is appropriate to capture the conventional design work which has taken place since 1990. This documents records regional and physical information used in site studies, summarizes the site studies for conventional facilities, and presents site layouts for buildings and utilities as they would have been at the end of the construction project. As such, this documents summarizes and complements the work of many groups in the SSC laboratory, the Texas National Research Laboratory Commission (TNRLC), and several subcontractors to the SSC project. The document contains extensive references to their work contained in other drafts and final reports. In particular, it borrows heavily from the Site Development Plan (released in draft form in January, 1992) which has, to date, guided aspects of site development

Technical Site Information: Planning group of the Directorate and Conventional Construction Division

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-11-01

This document presents the technical site information for the Superconducting Super Collider project. The Ellis County, Texas site was selected by the Department of Energy in 1989. After assembling the initial staff at temporary facilities in Dallas, the SSC Laboratory began site-specific design work. The resulting design for the SSC accelerators, experimental areas, and laboratory facilities were described in the Site-Specific Conceptual Design Report of July 1990. Since then, design specifications for the technical components and conventional facilities have been formulated. In fact, a very significant amount of surface and underground construction has been initiated and many buildings have been completed. Testing of prototypes for most technical components is advanced. The construction phase of the SSC project is approximately 20% complete. At this time, it is appropriate to capture the conventional design work which has taken place since 1990. This documents records regional and physical information used in site studies, summarizes the site studies for conventional facilities, and presents site layouts for buildings and utilities as they would have been at the end of the construction project. As such, this documents summarizes and complements the work of many groups in the SSC laboratory, the Texas National Research Laboratory Commission (TNRLC), and several subcontractors to the SSC project. The document contains extensive references to their work contained in other drafts and final reports. In particular, it borrows heavily from the Site Development Plan (released in draft form in January, 1992) which has, to date, guided aspects of site development.

A parameter network and model pyramid for managing technical information flow

International Nuclear Information System (INIS)

Sinnock, S.; Hartman, H.A.

1994-01-01

Prototypes of information management tools have been developed that can help communicate the technical basis for nuclear waste disposal to a broad audience of program scientists and engineers, project managers, and informed observers from stakeholder organizations. These tools include system engineering concepts, parameter networks expressed as influence diagrams, associated model hierarchies, and a relational database. These tools are used to express relationships among data-collection parameters, model input parameters, model output parameters, systems requirements, physical elements of a system description, and functional analysis of the contribution of physical elements and their associated parameters in satisfying the system requirements. By organizing parameters, models, physical elements, functions, and requirements in a visually reviewable network and a relational database the severe communication challenges facing participants in the nuclear waste dialog can be addressed. The network identifies the influences that data collected in the field have on measures of repository suitability, providing a visual, traceable map that clarifies the role of data and models in supporting conclusions about repository suitability. The map allows conclusions to be traced directly to the underlying parameters and models. Uncertainty in these underlying elements can be exposed to open review in the context of the effects uncertainty has on judgements about suitability. A parameter network provides a stage upon which an informed social dialog about the technical merits of a nuclear waste repository can be conducted. The basis for such dialog must be that stage, if decisions about repository suitability are to be based on a repository's ability to meet requirements embodied in laws and regulations governing disposal of nuclear wastes

PRACTICAL ASPECTS FOR DEVELOPMENT OF INFORMATIONAL AND EDUCATIONAL ENVIRONMENT OF HIGH TECHNICAL SCHOOL

Directory of Open Access Journals (Sweden)

Sergey F. Rodionov

2015-01-01

Full Text Available The approach is offered to development of the informational and educational environment of high technical school,based on deep integration of electronic educational content with methods and tools for the engineering problemssolving. The application program interface (API is used asthe main integration instrument, which modern Its have.

Microstructure and corrosion resistance of TC2 Ti alloy by laser cladding with Ti/TiC/TiB_2 powders

International Nuclear Information System (INIS)

Diao, Yunhua; Zhang, Kemin

2015-01-01

Highlights: • A TiC/TiB_2 composite coating was produced onto a TC2 Ti alloy by laser cladding with Ti/TiC/TiB_2 powders. • A maximum hardness of 1100 HV was achieved in the laser clad TiC/TiB_2 composite layer. • Corrosion resistance of the TC2 alloy in NaCl (3.5 wt%) aqueous solution can be improved after laser cladding. - Abstract: In the present work, a TiC/TiB_2 composite coating was produced onto a TC2 Ti alloy by laser cladding with Ti/TiC/TiB_2 powders. The surface microstructure, phase components and compositions were characterized with methods of optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffractometry (XRD), and energy dispersive spectrometry (EDS). The cladding layer is consisted of Ti, TiC and TiB_2. And the surface microhardness was measured. After laser cladding, a maximum hardness of 1100 HV is achieved in the laser cladding surface layer, which is more three times higher than that of the TC2 substrate (∼300 HV). Due to the formation of TiC and TiB_2 intermetallic compounds in the alloyed region and grain refinement, the microhardness of coating is higher than TC2 Ti alloy. In this paper, the corrosion property of matrix material and treated samples were both measured in NaCl (3.5 wt%) aqueous solution. From the result we can see that the laser cladding specimens’ corrosion property is clearly becoming better than that of the substrate.

Technical specification for the Quality Information Management System (QIMS) Pilot Project

Energy Technology Data Exchange (ETDEWEB)

Hall, R.C.; Claussen, L.M.; Thurston, I.

1992-01-01

This document contains implementation details for the Quality Information Management System (QIMS) Pilot Project, which has been released for VAX/VMS systems using the INGRES RDBMS. The INGRES Applications-By-Forms (ABF) software development tool was used to define the modules and screens which comprise the QIMS Pilot application. These specifications together with the QIMS information model and corresponding database definition constitute the QIMS technical specification and implementation description presented herein. The QIMS Pilot Project represents a completed software product which has been released for production use. Further extension projects are planned which will release new versions for QIMS. These versions will offer expanded and enhanced functionality to meet further customer requirements not accommodated by the QIMS Pilot Project.

Characteristics of laser clad α-Ti/TiC+(Ti,W)C1-x/Ti2SC+TiS composite coatings on TA2 titanium alloy

Science.gov (United States)

Zhai, Yong-Jie; Liu, Xiu-Bo; Qiao, Shi-Jie; Wang, Ming-Di; Lu, Xiao-Long; Wang, Yong-Guang; Chen, Yao; Ying, Li-Xia

2017-03-01

TiC reinforced Ti matrix composite coating with Ti2SC/TiS lubricant phases in-situ synthesized were prepared on TA2 titanium alloy by laser cladding with different powder mixtures: 40%Ti-19.5%TiC-40.5%WS2, 40%Ti-25.2%TiC-34.8%WS2, 40%Ti-29.4%TiC-30.6%WS2 (wt%). The phase compositions, microstructure, microhardness and tribological behaviors and wear mechanisms of coatings were investigated systematically. Results indicate that the main phase compositions of three coatings are all continuous matrix α-Ti, reinforced phases of (Ti,W)C1-x and TiC, lubricant phases of Ti2SC and TiS. The microhardness of the three different coatings are 927.1 HV0.5, 1007.5 HV0.5 and 1052.3 HV0.5, respectively. Compared with the TA2 titanium alloy (approximately 180 HV0.5), the microhardness of coatings have been improved dramatically. The coefficients of friction and the wear rates of those coatings are 0.41 and 30.98×10-5 mm3 N-1 m-1, 0.30 and 18.92×10-5 mm3 N-1 m-1, 0.34 and 15.98×10-5 mm3 N-1 m-1, respectively. Comparatively speaking, the coating fabricated with the powder mixtures of 40%Ti-25.2%TiC-34.8%WS2 presents superior friction reduction and anti-wear properties and the main wear mechanisms of that are slight plastic deformation and adhesive wear.

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 36: Technical uncertainty as a correlate of information use by US industry-affiliated aerospace engineers and scientists

Science.gov (United States)

Pinelli, Thomas E.; Glassman, Nanci A.; Affelder, Linda O.; Hecht, Laura M.; Kennedy, John M.; Barclay, Rebecca O.

1994-01-01

This paper reports the results of an exploratory study that investigated the influence of technical uncertainty on the use of information and information sources by U.S. industry-affiliated aerospace engineers and scientists in completing or solving a project, task, or problem. Data were collected through a self-administered questionnaire. Survey participants were U.S. aerospace engineers and scientists whose names appeared on the Society of Automotive Engineers (SAE) mailing list. The results support the findings of previous research and the following study assumptions. Information and information-source use differ for projects, problems, and tasks with high and low technical uncertainty. As technical uncertainty increases, information-source use changes from internal to external and from informal to formal sources. As technical uncertainty increases, so too does the use of federally funded aerospace research and development (R&D). The use of formal information sources to learn about federally funded aerospace R&D differs for projects, problems, and tasks with high and low technical uncertainty.

Formation and growth mechanism of TiC crystal in TiCp/Ti composites

Institute of Scientific and Technical Information of China (English)

金云学; 王宏伟; 曾松岩; 张二林

2002-01-01

Ti-C and Ti-Al-C alloys were prepared using gravity and directional solidification processes. Morphologies of TiC crystal were investigated by using SEM, XRD and EDX. Also, the formation and growth mechanism of TiC crystal have been analyzed on the basis of coordination polyhedron growth unit theory. During solidification of titanium alloys, the coordination polyhedron growth unit is TiC6. TiC6 growth units stack in a linking mode of edge to edge and form octahedral TiC crystal with {111} planes as present faces. Although the growing geometry of TiC crystal is decided by its lattice structure, the final morphology of TiC crystal depends on the effects of its growth environment. In solute concentration distribution, the super-saturation of C or TiC6 at the corners of octahedral TiC crystal is much higher than that of edges and faces of octahedral TiC crystal. At these corners the driving force for crystal growth is greater and the interface is instable which contribute to quick stacking rate of growth units at these corners and result in secondary dendrite arms along TiC crystallographic 〈100〉 directions. TiC crystal finally grows to be dendrites.

Technical knowledge and skills development in the informal sector in Kenya: The case of custom tailors

Science.gov (United States)

Apunda, Edwinah Amondi; de Klerk, Helena M.; Ogina, Teresa

2017-06-01

Custom tailors working in the informal sector in Nairobi, Kenya, mainly acquire technical skills through undertaking traditional apprenticeships (TAs). However, most of these tailors are semi-skilled, produce low-quality products and are often poorer than their formally trained counterparts. This qualitative case study explores the aspects of technical skills and knowledge which tailoring apprentices develop, and the factors which influence these outcomes. The findings show that apprentices do acquire basic technical skills for immediate application to ongoing tailoring activities (such as how to take body measurements, draft patterns, and cut, sew and finish constructed garments). However, apprentices do not acquire the technical knowledge that underpins the trade. Most master tailors who have completed TAs lack technical knowledge and have no access to technical skills upgrading. This perpetuates the cycle of basic and limited technical skills transfer to apprentices, poor performance and poverty among tailors. Both apprentices and master tailors expressed concern over knowledge limitations in TAs and a need to access further training to improve skills and acquire knowledge of the trade. The authors of this article argue that, technically and pedagogically, skilled master tailors are critical to improving training quality. Complementary training in theoretical knowledge is also important in improving apprentices' technical skills and understanding of the trade. Inclusion of TAs in government policy may help ensure sustainable improvement of skills.

Progress of studies on preparation of TiO2 photocatalysts with sol-gel auto igniting synthesis

Science.gov (United States)

Wu, Di; Shi, Zaifeng; Zhang, Xiaopeng; Xinghui, Wu

2017-11-01

In this article, influencing factors on the kinetics of the process of Sol-gel Auto igniting Synthesis (SAS) which is an advanced technology for preparing nanometer particles of inorganic materials were reviewed. The studies on preparing of nanometer TiO2 photocatalysts with SAS were focused. It was concluded that SAS will play an important role in practical preparing of high-pure nanometer TiO2 powder, and as a technical support, preparation of titania TiO2 from titanic iron ore with SAS is feasible and practicable.

Structural evolution of Ti/TiC multilayers

International Nuclear Information System (INIS)

Dahan, I.; Frage, N.; Dariel, M.P.

2004-01-01

Hard coatings based on metal/ceramic multilayers with periods in the nanometer range have been shown to possess some potential for improved tribological and mechanical properties. The present work is concerned with the structural evolution of (Ti/TiC) multilayers. Two kinds of multilayers consisting of 30 equithick (40 nm)TiC layers and 20 and 60 nm thick Ti layers, respectively, were sputter deposited on Mo substrates. The structural and the compositional evolution of these multilayers were examined by x-ray diffraction, transition electron microscopy (TEM), high-resolution TEM, Auger electron microscopy spectroscopy and differential thermal analysis (DTA), in the as-deposited state and after various heat treatments up to 500 deg. C. Initially, the Ti layers had a crystalline columnar grain structure displaying a (002) texture. The TiC layers displayed weak crystallinity with a pronounced (111) texture. In the course of the heat treatments, carbon diffused from the carbide layer into the adjacent Ti layers transforming the latter into off-stoichiometric TiC x with x≅0.5 and simultaneously depleting the carbon content of the initial carbide layer. The formed TiC x layers maintained the textural relationship with the neighboring TiC layers, consistent with a transformation that involved only a ABAB to ABC stacking change of the Ti sublattice. Increased mobility of the Ti atoms in carbon-depleted original TiC layers led to their full or partial recrystallization. The thermal effects associated both with the transformation of Ti layers into TiC, due to the influx of carbon atoms, and with the recrystallization of the original TiC layers were clearly revealed by the DTA measurements

Deposition and characterisation of multilayer hard coatings. Ti/TiNδ/TiCxNy/(TiC) a-C:H/(Ti) a-C:H

International Nuclear Information System (INIS)

Burinprakhon, T.

2001-02-01

Multilayer hard coatings containing Ti, TiNδ, TiC x N y , (TiC m ) a-C:H, (TiC n ) a-C:H, and (Ti) a-C:H were deposited on commercially pure titanium substrates by using an asymmetric bipolar pulsed-dc reactive magnetron sputtering of a titanium target, with Ar, Ar+N 2 , Ar+N 2 +CH 4 , and Ar+CH 4 gas mixtures. The microstructures, elemental compositions and bonding states of the interlayers and the coating surfaces were studied by using cross-sectional transmission electron microscopy (XTEM), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The microstructure development of the multilayer coating was strongly influenced by target poisoning. As a result of the complete poisoning of the titanium target during the deposition of TiNδ and TiC x N y interlayers, the a-C:H interlayers containing graded titanium and nitrogen contents were found to develop successively to the TiC x N y interlayer without the formation of near-stoichiometric TiC. The (TiC m ) a-C:H interlayer consisted of nano-particles of distorted fcc crystal structure embedded in the a-C:H matrix. The (TiC n ) a-C:H and (Ti) a-C:H top layers were found to be a-C:H matrix without nano-particles. In the (Ti) a-C:H top layer there was no measurable amount of Ti observed, regardless of the variation of CH 4 concentration between 37.5 and 60 % flow rate in Ar+-CH4 gas mixture. The top layer (Ti) a-C:H was found to contain approximately 10 atomic % nitrogen, due to N 2 contamination during deposition caused by low conductance of N 2 through the nominally closed valve of the mass flow controller. The change of the CH 4 concentration during deposition of the top layer (Ti) a-C:H, however, showed a strong influence on the hydrogen content. The comparison of the fluorescence background of the Raman spectra revealed that hydrogen-less (Ti) a-C:H was deposited at a CH 4 concentration of less than 50 % flow rate in Ar. The hardness

Fabrication and characterization of laminated Ti-(TiB+La2O3/Ti composite

Directory of Open Access Journals (Sweden)

Yuanfei Han

2015-10-01

Full Text Available The incorporation of ceramic particulate reinforcements into titanium alloys can improve the specific strength and specific stiffness, while inevitably reduce the plasticity and ductility. In this study, in situ synthesized multilayer Ti-(TiB+La2O3/Ti composite was designed by learning from the microstructure of nature biological materials with excellent mechanical properties. The Ti-(TiB+La2O3/Ti composite with unique characteristic of laminated structure was prepared by combined powder metallurgy and hot rolling. The method has the synthesize advantages with in-situ reaction of Ti and LaB6 at high temperature and controllability of reinforcements size and constituent phases in composites. The result shows that the pores in the as sintered laminated structure composite completely disappeared after hot rolling at 1050 °C. The agglomerated reinforcement particles were well dispersed and distributed uniformly along the rolling direction. The thickness of pure Ti layer and (TiB+La2O3/Ti composite layer decreased from 1 mm to about 200 μm. Meanwhile, the grains size was refined obviously after rolling deformation. The room temperature tensile test indicates that the elongation of the laminated Ti-(TiB+La2O3/Ti composite improved from 13% to 17% in comparison with the uniform (TiB+La2O3/Ti composite, while the tensile strength had little change. It provides theoretical and experimental basis for fabricating the novel high performance laminated Ti-(TiB+La2O3/Ti composites.

Academic & Technical Skills + Life/Work Skills + Career Information & Guidance = Success in Career Building.

Science.gov (United States)

Jarvis, Phillip S.

There has been a renaissance in the thinking about career development. It is becoming accepted that information is not enough; in addition to academic and technical skills, youth and adults need to learn life/work designing and building skills to become healthy, productive, and self-reliant citizens. Despite the fact that Canadian students have…

In situ NiTi/Nb(Ti) composite

International Nuclear Information System (INIS)

Jiang, Daqiang; Cui, Lishan; Jiang, Jiang; Zheng, Yanjun

2013-01-01

Graphical abstract: - Highlights: • In situ NiTi/Nb(Ti) composites were fabricated. • The transformation temperature was affected by the mixing Ti:Ni atomic ratios. • The NiTi component became micron-scale lamella after forging and rolling. • The composite exhibited high strength and high damping capacity. - Abstract: This paper reports on the creation of a series of in situ NiTi/Nb(Ti) composites with controllable transformation temperatures based on the pseudo-binary hypereutectic transformation of NiTi–Nb system. The composite constituent morphology was controlled by forging and rolling. It is found that the thickness of the NiTi lamella in the composite reached micron level after the hot-forging and cold-rolling. The NiTi/Nb(Ti) composite exhibited high damping capacity as well as high yield strength

Microstructure and corrosion resistance of TC2 Ti alloy by laser cladding with Ti/TiC/TiB{sub 2} powders

Energy Technology Data Exchange (ETDEWEB)

Diao, Yunhua, E-mail: 990722012@qq.com; Zhang, Kemin, E-mail: zhangkm@sues.edu.cn

2015-10-15

Highlights: • A TiC/TiB{sub 2} composite coating was produced onto a TC2 Ti alloy by laser cladding with Ti/TiC/TiB{sub 2} powders. • A maximum hardness of 1100 HV was achieved in the laser clad TiC/TiB{sub 2} composite layer. • Corrosion resistance of the TC2 alloy in NaCl (3.5 wt%) aqueous solution can be improved after laser cladding. - Abstract: In the present work, a TiC/TiB{sub 2} composite coating was produced onto a TC2 Ti alloy by laser cladding with Ti/TiC/TiB{sub 2} powders. The surface microstructure, phase components and compositions were characterized with methods of optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffractometry (XRD), and energy dispersive spectrometry (EDS). The cladding layer is consisted of Ti, TiC and TiB{sub 2}. And the surface microhardness was measured. After laser cladding, a maximum hardness of 1100 HV is achieved in the laser cladding surface layer, which is more three times higher than that of the TC2 substrate (∼300 HV). Due to the formation of TiC and TiB{sub 2} intermetallic compounds in the alloyed region and grain refinement, the microhardness of coating is higher than TC2 Ti alloy. In this paper, the corrosion property of matrix material and treated samples were both measured in NaCl (3.5 wt%) aqueous solution. From the result we can see that the laser cladding specimens’ corrosion property is clearly becoming better than that of the substrate.

Concentration of uranium on TiO-PAN and NaTiO-PAN composite absorbers

International Nuclear Information System (INIS)

Motl, Alois; Sebesta, Ferdinand; John, Jan; Spendlikova, Irena; Nemec, Mojmir

2013-01-01

Inorganic ion exchangers have been extensively tested for use in separation and concentration of uranium from Surface water. Except for separation of uranium from uranium -Contaminated waste water (e.g. waste water from mining and milling of uranium, Waste from nuclear fuel reprocessing) their main area of application has been foreseen to be their use for extraction of uranium from sea water which could partially cover future needs of uranium. Another perspective area of application is pre-concentration of uranium from natural waters followed by uranium determination via various specialized techniques such as TRLFS or AMS. Possibilities of uranium extraction from sea water have been subject of several international conferences (e.g. Topical meetings on the Recovery of Uranium from Seawater in 1980's, ACS National Meetings 2012 etc.) and are critically evaluated in a review by Bitte or recently by Kim. In the Czech Republic uranium-selective inorganic ion exchangers might be applied for treatment of various wastes from uranium industry, namely underground Water, uranium milling over-balance water, or acid waste water from underground uranium leaching and also like in other countries for determination of uranium isotopic composition focusing on anthropogenic and natural 236 U content. Among the best performing inorganic ion exchangers for the above listed purposes hydrated titanium dioxide (abbreviated as TiO) and sodium titanate (abbreviated as NaTiO) can be listed. Properties of TiO and NaTiO were reviewed by Lehto. From the point of view of ion-exchange, properties of hydrated titanium oxide and sodium titanate are very similar. The main disadvantage of these ion exchangers for industrial-scale application is their insufficient mechanical stability. To improve this property, the sorption materials can be embedded into a binding matrix. Modified polyacrylonitrile (PAN) has been proposed at the Czech Technical University in Prague as a universal binding matrix for

Effect of nano-CeO 2 on microstructure properties of TiC/TiN+TiCN ...

Indian Academy of Sciences (India)

TiC/TiN+TiCN-reinforced composite coatings were fabricated on Ti–6Al–4V alloy by laser cladding, which improved surface performance of the substrate. ... X-ray diffraction results indicated that Al3Ti+TiC/TiN+nano-CeO2 laser-cladded coating consisted of Ti3Al, TiC, TiN, Ti2Al20Ce, TiC0.3N0.7, Ce(CN)3 and CeO2, this ...

Prediction of two-dimensional electron gas mediated magnetoelectric coupling at ferroelectric PbTiO3/SrTiO3 heterostructures

Science.gov (United States)

Wei, Lan-ying; Lian, Chao; Meng, Sheng

2017-05-01

First-principles calculations predict the emergence of magnetoelectric coupling mediated by two-dimensional electron gas (2DEG) at the ferroelectric PbTiO3/SrTiO3 heterostructure. Free electrons endowed by naturally existing oxygen vacancies in SrTiO3 are driven to the heterostructure interface under the polarizing field of ferroelectric PbTiO3 to form a 2DEG. The electrons are captured by interfacial Ti atoms, which surprisingly exhibits ferromagnetism even at room temperature with a small critical density of ˜15.5 μ C /cm2 . The ferroelectricity-controlled ferromagnetism mediated by interfacial 2DEG shows strong magnetoelectric coupling strength, enabling convenient control of magnetism by electric field and vice versa. The PbTiO3/SrTiO3 heterostructure is cheap, easily grown, and controllable, promising future applications in low-cost spintronics and information storage at ambient condition.

Influence of Ta and Ti Doping on the High Field Performance of (Nb, Ta, Ti)3Sn Multifilamentary Wires based on Osprey Bronze with High Tin Content

International Nuclear Information System (INIS)

Abaecherli, V; Uglietti, D; Lezza, P; Seeber, B; Fluekiger, R; Cantoni, M; Buffat, P-A

2006-01-01

Ta and Ti are the most widely used additions for technical Nb 3 Sn multifilamentary superconductors. These elements are known to influence grain growth, grain morphology and chemical composition in the A15 layer, hence the current carrying properties of the wires over a wide magnetic field range. So far only few studies tried to compare systematically Ta and Ti doped and undoped Nb 3 Sn wires in the frame of the same work, down to a nanometric scale. We present an investigation on several multifilamentary (Nb, Ta, Ti) 3 Sn bronze route wires, fabricated at a laboratory scale, with various amounts of additives. The wires consist of fine filaments embedded in a Cu-Sn or Cu-Sn-Ti Osprey bronze with > 15 wt.% Sn and an external Cu stabilization. Microstructural observations are compared with the results of J c and n values measured up to 21 T at 4.2 and 2.2 K, and for longitudinal strains up to 0.5%. Non-Cu J c values up to 300 Amm -2 and n values up to 50 at 17 T and 4.2 K show clearly that wires with Ti addition to the bronze have a better performance with respect to wires with Ti additions to the filaments

Microstructure Characteristic of In-situ Ti/TiC Composites

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

TiC reinforced titanium composites has been produced with different Al content and C content by XDTM. The results have shown that TiC particles are of two different morphologies: coarse dendritical primary TiC and short bar-shape eutectic TiC. Al content has great effects on the morphology of TiC. With the increasing of Al content, the morphology of primary TiC changes from coarse developed dendrite into short bar-shape or plate-shape TiC with 35%Al. Meanwhile, the structure of the matrix changes from single Ti to Ti and Ti3Al, and to Ti3Al and TiAl. However, the C content has no influence on the microstructure of matrix. When the C content is less than 1.2%, the dendrite TiC disappears and only short bar-shape or plate-shape TiC exists in the composites. In addition, the effect of heat treatment on the morphology of TiC has also studied.

Synthesis of Nano-Ilmenite (FeTiO3) doped TiO2/Ti Electrode for Photoelectrocatalytic System

Science.gov (United States)

Hikmawati; Watoni, A. H.; Wibowo, D.; Maulidiyah; Nurdin, M.

2017-11-01

Ilmenite (FeTiO3) doped on Ti and TiO2/Ti electrodes were successfully prepared by using the sol-gel method. The structure, morphology, and optical properties of FeTiO3 are characterized by XRD, UV-Vis DRS, and SEM. The FeTiO3 and TiO2 greatly affect the photoelectrocatalysis performance characterized by Linear Sweep Voltammetry (LSV) and Cyclic Voltammetry (CV). The characterization result shows a band gap of FeTiO3 is 2.94 eV. XRD data showed that FeTiO3 formed at 2θ were 35.1° (110), 49.9° (024), and 61.2° (214). The morphology of FeTiO3/Ti and FeTiO3.TiO2/Ti using SEM shows that the formation of FeTiO3 thin layer signifies the Liquid Phase Deposition method effectively in the coating process. Photoelectrochemical (PEC) test showed that FeTiO3.TiO2/Ti electrode was highly oxidation responsive under visible light compared to the FeTiO3/Ti electrodes i.e. 7.87×10-4 A and 9.87×10-5 A. Degradation test of FeTiO3/Ti and FeTiO3.TiO2/Ti electrodes on titan yellow showed that the percentages of degradation with photoelectrocatalysis at 0.5 mg/L were 41% and 43%, respectively.

Fiscal Year 2001 Tank Characterization Technical Sampling Basis and Waste Information Requirements Document

International Nuclear Information System (INIS)

ADAMS, M.R.

2000-01-01

The Fiscal Year 2001 Tank Characterization Technical Sampling Basis and Waste Information Requirements Document (TSB-WIRD) has the following purposes: (1) To identify and integrate sampling and analysis needs for fiscal year (FY) 2001 and beyond. (2) To describe the overall drivers that require characterization information and to document their source. (3) To describe the process for identifying, prioritizing, and weighting issues that require characterization information to resolve. (4) To define the method for determining sampling priorities and to present the sampling priorities on a tank-by-tank basis. (5) To define how the characterization program is going to satisfy the drivers, close issues, and report progress. (6)To describe deliverables and acceptance criteria for characterization deliverables

Technical Information Resource on Rare Earth Elements Now Available to Public and Private Sector Stakeholders

Science.gov (United States)

A new EPA technical information resource, “Rare Earth Elements: A Review of Production, Processing, Recycling, and Associated Environmental Issues” has been produced as an introductory resource for those interested in learning more about REE mining and alternatives to meet demand...

Electrosynthesis of Ti5Si3, Ti5Si3/TiC, and Ti5Si3/Ti3SiC2 from Ti-Bearing Blast Furnace Slag in Molten CaCl2

Science.gov (United States)

Li, Shangshu; Zou, Xingli; Zheng, Kai; Lu, Xionggang; Chen, Chaoyi; Li, Xin; Xu, Qian; Zhou, Zhongfu

2018-04-01

Ti5Si3, Ti5Si3/TiC, and Ti5Si3/Ti3SiC2 have been electrochemically synthesized from the Ti-bearing blast furnace slag/TiO2 and/or C mixture precursors at a cell voltage of 3.8 V and 1223 K to 1273 K (950 °C to 1000 °C) in molten CaCl2. The pressed porous mixture pellets were used as the cathode, and a solid oxide oxygen-ion-conducting membrane (SOM)-based anode was used as the anode. The phase composition and morphologies of the cathodic products were systematically characterized. The final products possess a porous nodular microstructure due to the interconnection of particles. The variations of impurity elements, i.e., Ca, Mg, and Al, have been analyzed, and the result shows that Ca and Mg can be almost completely removed; however, Al cannot be easily removed from the pellet due to the formation of Ti-Al alloys during the electroreduction process. The electroreduction process has also been investigated by the layer-depended phase composition analysis of the dipped/partially reduced pellets to understand the detailed reaction process. The results indicate that the electroreduction process of the Ti-bearing blast furnace slag/TiO2 and/or C mixture precursors can be typically divided into four periods, i.e., (i) the decomposition of initial Ca(Mg,Al)(Si,Al)2O6, (ii) the reduction of Ti/Si-containing intermediate phases, (iii) the removal of impurity elements, and (iv) the formation of Ti5Si3, TiC, and Ti3SiC2. It is suggested that the SOM-based anode process has great potential to be used for the direct and facile preparation of Ti alloys and composites from cheap Ti-containing ores.

微量TiC对Mo-Ti-Zr-TiC合金性能与显微组织的影响%Effect of Trace TiC on Property and Microstructure of Mo-Ti-Zr-TiC Alloy

Institute of Scientific and Technical Information of China (English)

钱昭; 范景莲; 成会朝; 田家敏

2012-01-01

采用粉末冶金方法制备Mo-Ti-Zr-TiC合金,研究微量TiC的添加对Mo-Ti-Zr-TiC合金的拉伸性能和显微组织的影响.结果表明,在Mo-Ti-Zr合金中添加微量TiC(0.1％～0.5％,质量分数)后,合金的相对密度和室温抗拉强度得到了提高,当TiC添加量为0.4％时,合金强度最高,较Mo-Ti-Zr合金提高了28.1％.微量TiC的添加,阻碍了合金烧结过程中的晶粒长大,合金晶粒尺寸随TiC添加量的增加而降低.添加的细小TiC粒子在高温烧结过程中或与坯体中的微量氧发生反应形成了由Mo、Ti、C及O 4种元素组成的(Mo,Ti)xOyCz细小复合第二相粒子,或发生团聚结成大颗粒,对合金起到净化晶界氧和弥散强化的作用,因而合金的性能相比Mo-Ti-Zr合金有了较明显的提高.%Mo-Ti-Zr-TiC alloy was prepared via powder metallurgy method. The effects of trace TiC additive on the mechanical properties and microstructure of TiC reinforced Mo-Ti-Zr-TiC alloy were studied. The results indicate that the relative density and the tensile strength at room temperature of Mo-Ti-Zr-TiC alloy is effectively enhanced by adding trace TiC (0.1wt%~0.5wt%). The tensile strength achieves the highest value when the content of TiC is 0.4wt%, which is 28.1% higher than that of Mo-Ti-Zr alloy. The adding of trace TiC can inhibit the grain growth during alloy sintering process, which leads to the decrease of grain sizes with the rise of TiC content. A part of the fine TiC particles react with trace oxygen in molybdenum matrix to form (Mo,Ti)xOyC2 compound second phase particles during high temperature sintering, while the other part are agglomerated into large particles, which play a role in grain boundaries purification and dispersion-strengthening.

MISSE in the Materials and Processes Technical Information System (MAPTIS )

Science.gov (United States)

Burns, DeWitt; Finckenor, Miria; Henrie, Ben

2013-01-01

Materials International Space Station Experiment (MISSE) data is now being collected and distributed through the Materials and Processes Technical Information System (MAPTIS) at Marshall Space Flight Center in Huntsville, Alabama. MISSE data has been instrumental in many programs and continues to be an important source of data for the space community. To facilitate great access to the MISSE data the International Space Station (ISS) program office and MAPTIS are working to gather this data into a central location. The MISSE database contains information about materials, samples, and flights along with pictures, pdfs, excel files, word documents, and other files types. Major capabilities of the system are: access control, browsing, searching, reports, and record comparison. The search capabilities will search within any searchable files so even if the desired meta-data has not been associated data can still be retrieved. Other functionality will continue to be added to the MISSE database as the Athena Platform is expanded

The effects of boron in TiAl/Ti3Al

International Nuclear Information System (INIS)

Feng, C.R.; Michel, D.J.; Crowe, C.R.

1989-01-01

The authors discuss the TiAl/Ti 3 Al interfacial misfit dislocations structures investigated by TEM in Ti-45Al alloy and Ti-45Al/TiB 2 composite. For TiAl with c/a = 1.02, only a single set of misfit dislocation arrays are crystallographically possible; these were observed in Ti-45Al alloy. However, the observation of three sets of misfit dislocation arrays in the Ti-45Al/TiB 2 composite suggests that the occupation of octahedral sites in the TiAl structure by excess boron was responsible for a decrease in the c/a ratio leading to an increased fcc character of the TiAl at the TiAl/Ti 3 Al interface

Three dimensional visualization breakthrough in analysis and communication of technical information for nuclear waste management

International Nuclear Information System (INIS)

Alexander, D.H.; Cerny, B.A.; Hill, E.R.; Krupka, K.M.; Smoot, J.L.; Smith, D.R.; Waldo, K.

1990-11-01

Computer graphics systems that provide interactive display and manipulation of three-dimensional data are powerful tools for the analysis and communication of technical information required for characterization and design of a geologic repository for nuclear waste. Greater understanding of site performance and repository design information is possible when performance-assessment modeling results can be visually analyzed in relation to site geologic and hydrologic information and engineering data for surface and subsurface facilities. In turn, this enhanced visualization capability provides better communication between technical staff and program management with respect to analysis of available information and prioritization of program planning. A commercially-available computer system was used to demonstrate some of the current technology for three-dimensional visualization within the architecture of systems for nuclear waste management. This computer system was used to interactively visualize and analyze the information for two examples: (1) site-characterization and engineering data for a potential geologic repository at Yucca Mountain, Nevada; and (2) three-dimensional simulations of a hypothetical release and transport of contaminants from a source of radionuclides to the vadose zone. Users may assess the three-dimensional distribution of data and modeling results by interactive zooming, rotating, slicing, and peeling operations. For those parts of the database where information is sparse or not available, the software incorporates models for the interpolation and extrapolation of data over the three-dimensional space of interest. 12 refs., 4 figs

Technical advisory on SSC site criteria and catalog of site information needs

Energy Technology Data Exchange (ETDEWEB)

1985-06-15

The Superconducting Super Collider, or SSC, is a proposed scientific instrument of the study of the fundamental nature of matter. In the SSC two 20-TeV beams of protons will be accelerated and counter circulate on an approximately circular path. The protons will be made to collide at six locations where detectors can be placed to count and measure the products of the collisions. These collisions, twenty times more energetic than in any existing facility, will enable scientists to probe deeper into the heart of matter in the quest for a deeper understanding of the universal forces of nature. The goal of the SSC project is to create a scientific laboratory in high energy physics whose facilities are unique. Ultimately the success of that laboratory will be measured by its scientific discoveries, measurements, interpretations, and innovations. Toward that end the accelerator-collider must be constructed to high standards at minimum cost and maximum effectiveness. Preparations must be made for future operations and a scientific-technical staff attracted and maintained. The chosen site must accommodate all of these factors. This document summarizes siting criteria for the SSC and enumerates site-specific information important to the evaluation of potential sites. This document is not a call for site proposals but a technical report prepared for the information and use of the Department of Energy (DOE).

Liquid phase interaction in TiC0,5N0,5-TiNi-Mo and TiC0,5N0,5-TiNi-Ti-Mo

International Nuclear Information System (INIS)

Askarova, L.Kh; Grigorov, I.G.; Zajnulin, Yu.G.

1998-01-01

Using the methods of X ray diffraction analysis, electron microscopy and X ray spectrum microanalysis a study was made into specific features of phase and structure formation in alloys TiC 0,5 N 0,5 -TiNi-Mo and TiC 0,5 N 0,5 -TiNi-Mo in the presence of a liquid phase at temperatures of 1380-1600 deg C. It is revealed that the physical and chemical processes taking place during the liquid-phase sintering result in the formation of a three-phase alloy consisting of nonstoichiometric titanium carbonitride TiC 0.5-x N 0.5-x , a molybdenum base solid solution of titanium, nickel and carbon Mo(Ti, Ni, C) and one of two intermetallic compounds, either TiNi or Ni 3 Ti. Metallic element concentration in individual phase constituents of the alloy is determined by means of X ray spectrum microanalysis

Mechanical Engineering Department technical abstracts

International Nuclear Information System (INIS)

Denney, R.M.

1982-01-01

The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

An approach to knowledge structuring for advanced phases of the Technical and Management Information System (TMIS)

Science.gov (United States)

Goranson, H. T.

1986-01-01

The Technical and Management Information System (TMIS) must employ on enlightened approach to its object structure, but basic issues in conceptual structuring remain to be resolved. Sirius outlines the necessary agenda and reports on progress toward solutions.

PROJECT EVALUATION OF TECHNICAL CONDITION OF SHIP STRUCTURES WITH USE OF INFORMATION RETRIEVAL SYSTEMS

Directory of Open Access Journals (Sweden)

Юлия Алексеевна КАЗИМИРЕНКО

2015-06-01

Full Text Available The mechanisms for evaluation of technical conditions of ship constructions were investigated and was developed a new specialized informational and search system for the collection, analysis and processing the defects of new materials during the designing, construction, operation of ships and floating structures for transportation of goods 1, 4, 6-8 classes of danger.

Isothermal section of the Ti-Si-B system at 1250 ° C in the Ti-TiSi2-TiB2 region

OpenAIRE

Ramos, Alfeu Saraiva; Baldan, Renato; Nunes, Carlos Angelo; Coelho, Gilberto Carvalho; Suzuki, Paulo Atsushi; Rodrigues, Geovani

2013-01-01

A partial isothermal section (Ti-TiSi2-TiB2 region) of the ternary Ti-Si-B system at 1250 ° C was determined from heat-treated alloys prepared via arc melting. Microstructural characterization has been carried out through scanning electron microscopy (SEM), x-ray diffraction (xRD) and wavelength dispersive spectrometry (WDS). The results have shown the stability of the near stoichiometric Ti6Si2B phase and a negligible solubility of boron in the Ti-silicides as well as of Si in the Ti-borides...

Informational Reinforcement of Students’ Course Design Aimed at Promoting Engineers Training Quality in Technical Education

Directory of Open Access Journals (Sweden)

B. N. Guzanov

2012-01-01

Full Text Available Using the modern information technologies in educational process is regarded as one of the main directions in training the qualified specialists with systematic engineering thinking. The optimum combination of various educational technologies and computerized resources can improve teaching quality and promote students’ professional level. Taking as an example one of the basic technical disciplines of the engineering training curriculum at a technical higher school, the authors describe the computerized technology facilitating the course design. The technology in question - the «Reduktor» courseware - adapts the complex product of Autodesk –AutoCAD for educational purposes. The above program is the enhanced interface of AutoCAD, linked to the Microsoft Excel spreadsheet and the reference data library used for designing the reduction gear. The experimental research, based on the qualimetric approach and continuous diagnostic and prognostic monitoring of the key indices of knowledge acquisition, proves the effectiveness of informational reinforcement of students self-dependent work. 

Technical noise supplement : TeNS : a technical supplement to the Traffic Noise Analysis Protocol.

Science.gov (United States)

1998-10-01

The purpose of this Technical Noise Supplement (TeNS) is to provide technical background : information on transportation-related noise in general and highway traffic noise in : particular. It is designed to elaborate on technical concepts and procedu...

OSH technical reference manual

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

How to find technical information. Pt. 2. Wie finde ich technische Informationen. T. 2. Elektrotechnik, Elektronik, Datenverarbeitung, Mess-, Steuerungs- und Reglungstechnik, Bauingenieurwesen, Architektur, Umweltschutz

Energy Technology Data Exchange (ETDEWEB)

Joswig, W

1981-01-01

This introduction into the finding and ordering of technical literature addresses both students and doctoral candidates as well as engineers which are already practising their profession. The first chapter - library science - gives a basic description of bibliographic research in an average scientific library: reading rooms and their function, structure of catalogues, structure of the reference library as well as lending and interlibrary lending methods. The technical information systems are described in detail. Finally, translation services and technical information and documentation centres are named. The second chapter - bibliographic research - lists the most important aids in finding technical references. Chapter three outlines the topical complex of scientific work. It provides information on how to organize written scientific publications in a formally correct way, how to quote and to list the references. Chapter four contains an index of terms from library and bibliographic science which is to help the beginner to understand the technical terms which cannot completely be excluded from this orientation aid.

Fabrication and Mechanical Properties of TiC/TiAl Composites

Institute of Scientific and Technical Information of China (English)

YUE Yun-long; GONG Yan-sheng; WU Hai-tao; WANG Chuan-bin; ZHANG Lian-meng

2004-01-01

TiC/TiAl composites with different TiC content were fabricated by rapid heating technique ofspark plasma sintering (SPS). The effect of TiC particles on microstructure and mechanical properties of TiAl matrix was investigated. The results indicate that grain sizes of TiAl matrix decrease and mechanical properties are improved because of the addition of TiC particles. The composites display a 26.8% increase in bending strength when10wt% TiC is added and 43.8% improvement in fracture toughness when 5 wt % TiC is added compared to valuesof TiC-free materials. Grain-refinement and dispersion-strengthening were the main strengthening mechanism. Theimprovement of fracture toughness was due to the deflexion of TiC particles to the crack.

Materials And Processes Technical Information System (MAPTIS) LDEF materials data base

Science.gov (United States)

Funk, Joan G.; Strickland, John W.; Davis, John M.

1993-01-01

A preliminary Long Duration Exposure Facility (LDEF) Materials Data Base was developed by the LDEF Materials Special Investigation Group (MSIG). The LDEF Materials Data Base is envisioned to eventually contain the wide variety and vast quantity of materials data generated from LDEF. The data is searchable by optical, thermal, and mechanical properties, exposure parameters (such as atomic oxygen flux) and author(s) or principal investigator(s). Tne LDEF Materials Data Base was incorporated into the Materials and Processes Technical Information System (MAPTIS). MAPTIS is a collection of materials data which has been computerized and is available to engineers, designers, and researchers in the aerospace community involved in the design and development of spacecraft and related hardware. The LDEF Materials Data Base is described and step-by-step example searches using the data base are included. Information on how to become an authorized user of the system is included.

Epoxidation of limonene over Ti MCM 41 and Ti BETA

International Nuclear Information System (INIS)

Cubillos Lobo, Jairo Antonio; Gonzalez Rodriguez, Lina Maria; Montes de Correa, Consuelo

2002-01-01

Ti MCM 41 were synthesized and evaluated in the epoxidation of limonene, using peroxide of hydrogen (H 2 O) as agent oxidizer. The characteristic hexagonal phase of Ti MCM 41 was obtained by heating the precursor gel during three days at 100 centigrade degrees. Further heating up to ten days leads to a decrease of this phase. The increase (Ti) in the synthesis gel also decreases that phase. The increase of Ti in the synthesis gel also decreases that phase UV VIS and FTIR spectroscopy indicates that Ti was incorporated in the lattice of Ti MCM 41 as well as, in Ti BETA. SEM micrographs of Ti MCM 41 show that the morphology changes with the Ti loading. Ti MCM 41 was most active than Ti BETA for limonene epoxidation even though both show high selectivity to epoxides

Information management architecture for an integrated computing environment for the Environmental Restoration Program. Environmental Restoration Program, Volume 3, Interim technical architecture

International Nuclear Information System (INIS)

1994-09-01

This third volume of the Information Management Architecture for an Integrated Computing Environment for the Environmental Restoration Program--the Interim Technical Architecture (TA) (referred to throughout the remainder of this document as the ER TA)--represents a key milestone in establishing a coordinated information management environment in which information initiatives can be pursued with the confidence that redundancy and inconsistencies will be held to a minimum. This architecture is intended to be used as a reference by anyone whose responsibilities include the acquisition or development of information technology for use by the ER Program. The interim ER TA provides technical guidance at three levels. At the highest level, the technical architecture provides an overall computing philosophy or direction. At this level, the guidance does not address specific technologies or products but addresses more general concepts, such as the use of open systems, modular architectures, graphical user interfaces, and architecture-based development. At the next level, the technical architecture provides specific information technology recommendations regarding a wide variety of specific technologies. These technologies include computing hardware, operating systems, communications software, database management software, application development software, and personal productivity software, among others. These recommendations range from the adoption of specific industry or Martin Marietta Energy Systems, Inc. (Energy Systems) standards to the specification of individual products. At the third level, the architecture provides guidance regarding implementation strategies for the recommended technologies that can be applied to individual projects and to the ER Program as a whole

Microstructural evolution and wear behaviors of laser cladding Ti_2Ni/α(Ti) dual-phase coating reinforced by TiB and TiC

International Nuclear Information System (INIS)

Song, R.; Li, J.; Shao, J.Z.; Bai, L.L.; Chen, J.L.; Qu, C.C.

2015-01-01

Graphical abstract: - Highlights: • A TiC+TiB reinforced intermetallic matrix coating was fabricated by laser cladding. • The microstructural evolution of the reinforcements was analyzed. • A formula was established in term of wear loss, sliding time and applied load. • Wear behaviors were investigated by in situ continuing tests in different time intervals. • The transformation of wear mechanism at different applied loads was revealed. - Abstract: The Ti_2Ni/α(Ti) dual-phase coating reinforced by TiB and TiC was fabricated on the Ti6Al4V substrate by laser cladding. Phase constituents were confirmed by a theoretical prediction combined with X-ray diffraction (XRD) analyses. From the surface to the bottom of the coating, a regular evolution of the reinforcements’ microstructure, namely TiC_p+(TiB+TiC)_e, (TiB+TiC)_e and TiB_p+(TiB+TiC)_e (p and e were the abbreviations of primary and eutectic, respectively), was investigated by scanning electron microscopy (SEM). The coating possessed the higher microhardness than that of the substrate. An in situ dynamic method (in situ continuing tests at different time intervals) was designed to reveal wear behaviors at different wear stages. A quantitative calculation formula was established by a mathematic model to predict wear losses under different sliding time and applied loads in a definite precision. The wear mechanism was transformed from brittle debonding (at 10 N) to the joint action of brittle debonding and micro-cutting (at 20 N and 30 N) due to the microstructural evolution across the depth from the surface of the coating.

Microstructure of in-situ Synthesized (TiB+TiC)/Ti Composites Prepared by Hot-pressing

Institute of Scientific and Technical Information of China (English)

Zhenzhu ZHENG; Lin GENG; Honglin WANG; Weimin ZHOU; Hongyu XU

2003-01-01

In-situ 5 vol.pct TiB whiskers and TiC particulates reinforced Ti composites were fabricated by blending Ti powderand B4C particulates followed by reactive hot-pressing. The microstructure of the composites was investigated byusing differential scanning c

Stress analysis and microstructure of PVD monolayer TiN and multilayer TiN/(Ti,Al)N coatings

NARCIS (Netherlands)

Carvalho, NJM; Zoestbergen, E; Kooi, BJ; De Hosson, JTM

2003-01-01

Two PVD titanium nitride based coatings; monolayer TiN and multilayer resulting from the stacking of TiN and (Ti,Al)N layers were evaluated with respect to their stress state and microstructure. The TiN was deposited by triode evaporation ion plating, whereas the TiN/(Ti,AI)N was deposited using a

Technical Network

CERN Multimedia

2007-01-01

In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

Microstructure and Properties of (TiB2 + NiTi)/Ti Composite Coating Fabricated by Laser Cladding

Science.gov (United States)

Lin, Yinghua; Lei, Yongping; Fu, Hanguang; Lin, Jian

2015-10-01

Agglomerated TiB2 particle and network-like structure-reinforced titanium matrix composite coatings were prepared by laser cladding of the Ni + TiB2 + Ti preplaced powders on Ti-6Al-4V alloy. The network-like structure mainly consisted of NiTi and Ni3Ti. Through the experiment, it was found that the size of agglomerated particle gradually decreased with the increase of Ti content, but the number of the network-like structure first increased and then disappeared. In-situ reaction competition mechanism and the formation of network-like structure were discussed. The average micro-hardness gradually decreased with the increase of Ti content, but the average fracture toughness gradually increased. Meanwhile, the wear resistance of the coatings is higher than that of the substrate, but the wear loss of the coatings is gradually increased with the increase of Ti content.

Technical and management information system: The tool for professional productivity on the space station program

Science.gov (United States)

Montoya, G.; Boldon, P.

1985-01-01

The Space Station Program is highly complex not only in its technological goals and requirements but also in its organizational structure. Eight Contractor teams supporting four NASA centers plus Headquarters must depend on effective exchange of information--the lifeblood of the program. The Technical and Management Information System (TMIS) is the means by which this exchange can take place. Value of the TMIS in increasing productivity comes primarily from its ability to make the right information available to whomever needs it when it is needed. Productivity of the aerospace professional and how it can be enhanced by the use of specifically recommended techniques and procedures for information management using the TMIS are discussed.

Antibacterial activity and cell compatibility of TiZrN, TiZrCN, and TiZr-amorphous carbon coatings

Energy Technology Data Exchange (ETDEWEB)

Huang, Heng-Li [School of Dentistry, China Medical University, Taichung 404, Taiwan (China); Department of Bioinformatics and Medical Engineering, Asia University, Taichung 41354, Taiwan (China); Chang, Yin-Yu, E-mail: yinyu@nfu.edu.tw [Department of Mechanical and Computer-aided Engineering, National Formosa University, Yunlin 632, Taiwan (China); Liu, Jia-Xu [Department of Mechanical and Computer-aided Engineering, National Formosa University, Yunlin 632, Taiwan (China); Tsai, Ming-Tzu [Department of Biomedical Engineering, Hungkuang University, Taichung 433, Taiwan (China); Lai, Chih-Ho [Department of Microbiology and Immunology, Graduate Institute of Biomedical Sciences, Chang Gung University, Taoyuan, Taiwan (China)

2015-12-01

A cathodic-arc evaporation system with plasma-enhanced duct equipment was used to deposit TiZrN, TiZrCN, and TiZr/a-C coatings. Reactive gases (N{sub 2} and C{sub 2}H{sub 2}) activated by the Ti and Zr plasma in the evaporation process was used to deposit the TiZrCN and TiZr/a-C coatings with different C and nitrogen contents. The crystalline structures and bonding states of coatings were analyzed by X-ray diffraction and X-ray photoelectron spectroscopy. The microbial activity of the coatings was evaluated against Staphylococcus aureus (Gram-positive bacteria) and Actinobacillus actinomycetemcomitans (Gram-negative bacteria) by in vitro antibacterial analysis using a fluorescence staining method employing SYTO9 and a bacterial-viability test on an agar plate. The cell compatibility and morphology related to CCD-966SK cell-line human skin fibroblast cells on the coated samples were also determined using the 3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide assay, reverse-transcriptase-polymerase chain reaction, and scanning electron microscopy. The results suggest that the TiZrCN coatings not only possess better antibacterial performance than TiZrN and TiZr/a-C coatings but also maintain good compatibility with human skin fibroblast cells. - Highlights: • TiZrN, TiZrCN, and TiZr/a-C coatings were deposited using cathodic arc evaporation. • The TiZrCN showed a composite structure containing TiN, ZrN, and a-C. • The TiZrCN-coated Ti showed the least hydrophobicity among the samples. • The TiZrCN-coated Ti showed good human skin fibroblast cell viability. • The TiZrCN-coated Ti exhibited good antibacterial performance.

Critical Analysis of the Quality, Readability, and Technical Aspects of Online Information Provided for Neck-Lifts.

Science.gov (United States)

Rayess, Hani; Zuliani, Giancarlo F; Gupta, Amar; Svider, Peter F; Folbe, Adam J; Eloy, Jean Anderson; Carron, Michael A

2017-03-01

The number of patients using the internet to obtain health information is growing. This material is unregulated and heterogeneous and can influence patient decisions. To compare the quality, readability, and technical aspects of online information about neck-lifts provided by private practice websites vs academic medical centers and reference sources. In this cross-sectional analysis conducted between November 2015 and January 2016, a Google search of the term neck-lift was performed, and the first 45 websites were evaluated. The websites were categorized as private practice vs other. Private websites (PWs) included sites created by private practice physicians. Other websites (OWs) were created by academic medical centers or reference sources. Quality, readability, and technical aspects of online websites related to neck-lifts. Quality was assessed using the DISCERN criteria and the Health on the Net principles (HONcode). Readability was assessed using 7 validated and widely used criteria. Consensus US reading grade level readability was provided by a website (readabilityformulas.com). Twelve technical aspects were evaluated based on criteria specified by medical website creators. Forty-five websites (8 OWs [18%] and 37 PWs [82%]) were analyzed. There was a significant difference in quality between OWs and PWs based on the DISCERN criteria and HONcode principles. The DISCERN overall mean (SD) scores were 2.3 (0.5) for OWs and 1.3 (0.3) for PWs (P analysis, the mean (SD) was 8.6 (1.8) (range, 5-11) for OW, and the mean (SD) was 5.8 (1.7) (range, 2-9) for PW. The mean (SD) readability consensus reading grade level scores were 11.7 (1.9) for OWs and 10.6 (1.9) for PWs. Of a total possible score of 12, the mean (SD) technical scores were 6.3 (1.8) (range, 4-9) for OWs and 6.4 (1.5) (range, 3-9) for PWs. Compared with PWs, OWs had a significantly higher quality score based on both the DISCERN criteria and HONcode principles. The mean readability for OWs and PWs was

Technical training: places available

CERN Multimedia

2014-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Technical training: places available

CERN Document Server

2013-01-01

If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Technical training - places available

CERN Document Server

2013-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Preparation of Al-Ti-B grain refiner by SHS technology[Self-propagating High-temperature Synthesis

Energy Technology Data Exchange (ETDEWEB)

Nikitin, V.I.; Wanqi, J.I.E.; Kandalova, E.G.; Makarenko, A.G.; Yong, L.

2000-02-01

Since the discovery of the grain refinement effect of aluminum by titanium, especially with the existence of B or C in 1950, grain refiners are widely accepted in industry for microstructure control of aluminum alloys. Research on this topic is to obtain the highest grain refinement efficiency with the lowest possible addition of master alloy. It is widely accepted that the morphology and size of TiAl{sub 3} particles, which are known as heterogeneous nucleation centers, are important factors deterring the grain refinement efficiency. Fine TiAl{sub 3} particles are favorable. The grain refinement process shows a heredity phenomenon, which means that structural information from initial materials transfers through a melt to the final product. It is important to find the connection between microstructural parameters of the master alloy and the final product. To improve the quality of Al-Ti-B master alloys for the use as a grain refiner, a new method based on SHS (self-propagating high-temperature synthesis) technology has been developed in Samara State Technical University to produce the master alloys. SHS, as a new method for preparation of materials, was first utilized by Merzhanov in 1967. This method uses the energy from highly exothermic reactions to sustain the chemical reaction in a combustion wave. The advantages of SHS include simplicity, low energy requirement, and higher product purity. Because SHS reactions can take place between elemental reactants, it is easy to control product composition. The purposes of this investigation were to fabricate an SHS Al-5%Ti-1%B master alloy, to analyze its structure and to test its grain refining performance.

Technical training: places available

CERN Multimedia

2014-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Marie Lahchimi, Technical Training Administration (Tel: 74924)

Highly uniform bipolar resistive switching characteristics in TiO2/BaTiO3/TiO2 multilayer

International Nuclear Information System (INIS)

Ma, W. J.; Zhang, X. Y.; Wang, Ying; Zheng, Yue; Lin, S. P.; Luo, J. M.; Wang, B.; Li, Z. X.

2013-01-01

Nanoscale multilayer structure TiO 2 /BaTiO 3 /TiO 2 has been fabricated on Pt/Ti/SiO 2 /Si substrate by chemical solution deposition method. Highly uniform bipolar resistive switching (BRS) characteristics have been observed in Pt/TiO 2 /BaTiO 3 /TiO 2 /Pt cells. Analysis of the current-voltage relationship demonstrates that the space-charge-limited current conduction controlled by the localized oxygen vacancies should be important to the resistive switching behavior. X-ray photoelectron spectroscopy results indicated that oxygen vacancies in TiO 2 play a crucial role in the resistive switching phenomenon and the introduced TiO 2 /BaTiO 3 interfaces result in the high uniformity of bipolar resistive switching characteristics

Study of excited states in 48Ti, 49Ti and 50Ti by means of radiative neutron capture

International Nuclear Information System (INIS)

Ruyl, J.F.A.G.

1983-12-01

The γ radiation produced by thermal neutron capture in a natural Ti target and in enriched 47 Ti and 49 Ti targets has been investigated. In the analysis 57 excited states of 48 Ti, 28 of 49 Ti and 31 of 50 Ti have been identified. The values for the 48 Ti and 49 Ti neutron binding energy agree with previous data, the value for 50 Ti differs by five standard deviations. The nature of the neutron capture mechanism has been investigated by comparing the present results with those from previous (d,p) work. It appears that in 47 Ti capture proceeds through a doorway state and that the potential capture mechanism is valid for 48 Ti and 49 Ti. The Fermi gas model gives a good representation of the nuclear level density in all three nuclei. From a measurement of the γ-ray circular polarization resulting from the capture of polarized neutrons, combined with previous (d,p) work, the spins of five 49 Ti levels could be determined, and those of 13 other 49 Ti levels could be confirmed. The combination of nuclear orientation measurements and circular polarization measurements had yielded the unambiguous determination of the spins of one 48 Ti state and of five 50 Ti states. Further spin and parity determinations for six 48 Ti and for five 50 Ti states have been obtained from the analysis of the identified branches together with the results of previous experiments. Shell-model calculations, which yielded excitation energies, branching ratios, lifetimes and (d,p) spectroscopic factors, give a good representation of the experimental data for the low-lying states in both even-even nuclei. (Auth.)

Influence of electric current on microstructure evolution in Ti/Al and Ti/TiAl{sub 3} during spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Sun, Y. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Haley, J. [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Kulkarni, K. [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016, UP (India); Aindow, M. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Lavernia, E.J., E-mail: lavernia@ucdavis.edu [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Department of Chemical Engineering and Materials Science, University of California, Irvine, CA 92697-2575 (United States)

2015-11-05

The synthesis of γ-TiAl from elemental metals via solid-state reactive diffusion processing routes involves multiple reaction steps with the formation of various intermediate intermetallic compounds, starting with TiAl{sub 3} because this phase is favored kinetically. To understand the processes by which the TiAl{sub 3} intermediate is eliminated during synthesis of γ-TiAl alloy via spark plasma sintering (SPS), the reaction between Ti and TiAl{sub 3} during SPS was studied with emphasis on the effects of the applied electric current and starting TiAl{sub 3} microstructure on the reaction kinetics and the underlying diffusion mechanisms. The intermediate intermetallic phases Ti{sub 3}Al, TiAl and TiAl{sub 2} were formed between the Ti and TiAl{sub 3} upon SPS processing at 900 °C. The applied electric current did not alter the character of the phases formation in the Ti/TiAl{sub 3} system, but thermodynamic calculations suggest that the activation energy for the nucleation of TiAl{sub 2} is reduced significantly with an electric current flowing. Moreover, the kinetics of the reactions between Ti and TiAl{sub 3} were enhanced when the starting TiAl{sub 3} microstructure was refined. The electric field also had a more significant influence on the grain growth kinetics for TiAl{sub 2} and TiAl in powder blend compacts with refined microstructures. - Highlights: • Reaction between Ti and TiAl{sub 3} during spark plasma sintering was studied. • Refined starting TiAl{sub 3} microstructure enhanced the reactions kinetics. • The nucleation barrier of TiAl{sub 2} was reduced by the applied electric field. • The applied electric field restrained the grain growth of TiAl and TiAl{sub 2}.

Microstructural evolution and wear behaviors of laser cladding Ti{sub 2}Ni/α(Ti) dual-phase coating reinforced by TiB and TiC

Energy Technology Data Exchange (ETDEWEB)

Song, R.; Li, J., E-mail: jacob_lijun@sina.com; Shao, J.Z.; Bai, L.L.; Chen, J.L.; Qu, C.C.

2015-11-15

Graphical abstract: - Highlights: • A TiC+TiB reinforced intermetallic matrix coating was fabricated by laser cladding. • The microstructural evolution of the reinforcements was analyzed. • A formula was established in term of wear loss, sliding time and applied load. • Wear behaviors were investigated by in situ continuing tests in different time intervals. • The transformation of wear mechanism at different applied loads was revealed. - Abstract: The Ti{sub 2}Ni/α(Ti) dual-phase coating reinforced by TiB and TiC was fabricated on the Ti6Al4V substrate by laser cladding. Phase constituents were confirmed by a theoretical prediction combined with X-ray diffraction (XRD) analyses. From the surface to the bottom of the coating, a regular evolution of the reinforcements’ microstructure, namely TiC{sub p}+(TiB+TiC){sub e}, (TiB+TiC){sub e} and TiB{sub p}+(TiB+TiC){sub e} (p and e were the abbreviations of primary and eutectic, respectively), was investigated by scanning electron microscopy (SEM). The coating possessed the higher microhardness than that of the substrate. An in situ dynamic method (in situ continuing tests at different time intervals) was designed to reveal wear behaviors at different wear stages. A quantitative calculation formula was established by a mathematic model to predict wear losses under different sliding time and applied loads in a definite precision. The wear mechanism was transformed from brittle debonding (at 10 N) to the joint action of brittle debonding and micro-cutting (at 20 N and 30 N) due to the microstructural evolution across the depth from the surface of the coating.

Experimental investigation on local mechanical response of superelastic NiTi shape memory alloy

International Nuclear Information System (INIS)

Xiao, Yao; Zeng, Pan; Lei, Liping

2016-01-01

In this paper, primary attention is paid to the local mechanical response of NiTi shape memory alloy (SMA) under uniaxial tension. With the help of in situ digital image correlation, sets of experiments are conducted to measure the local strain field at various thermomechanical conditions. Two types of mechanical responses of NiTi SMA are identified. The residual strain localization phenomena are observed, which can be attributed to the localized phase transformation (PT) and we affirm that most of the irreversibility is accumulated simultaneously during PT. It is found that temperature and PT play important roles in inducing delocalization of the reverse transformation. We conclude that forward transformation has more influence on the transition of mechanical response in NiTi SMA than reverse transformation in terms of the critical transition temperature for inducing delocalized reverse transformation. (technical note)

Technical training: places available

CERN Multimedia

2013-01-01

If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tél : 74924)  

Effect of nano-CeO2 on microstructure properties of TiC/TiN+nTi(CN) reinforced composite coating

International Nuclear Information System (INIS)

Jianing, Li; Chuanzhong, Chen; Cuifang, Zhang

2012-01-01

TiC/TiN+TiCN reinforced composite coatings were fabricated on Ti-6Al-4V alloy by laser cladding, which improved surface performance of the substrate. Nano-CeO 2 was able to suppress crystallization and growth of the crystals in the laser-cladded coating to a certain extent. With the addition of proper content of nano-CeO 2 , this coating exhibited fine microstructure. In this study, the Al 3 Ti+TiC/TiN+nano-CeO 2 laser-cladded coatings were studied by means of X-ray diffraction and scanning electron microscope. The X-ray diffraction results indicated that the Al 3 Ti+TiC/TiN+nano-CeO 2 laser-cladded coating consisted of Ti 3 Al, TiC, TiN, Ti 2 Al 20 Ce, TiC 0.3 N 0.7 , Ce(CN) 3 and CeO 2 , this phase constituent was beneficial to increase the microhardness and wear resistance of Ti-6Al-6V alloy. (author)

In-situ EXAFS study on the thermal decomposition of TiH2

International Nuclear Information System (INIS)

Zhou Yingli; Wu Min; An Pengfei; Zheng Lirong; Chu Shengqi; Zhang Jing; Hu Tiandou

2014-01-01

Thermal decomposition behaviors of TiH 2 powder under a flowing helium atmosphere and in a low vacuum condition have been studied using an in situ EXAFS technique. By an EXAFS analysis containing the multiple scattering paths including H atoms, the changes of the hydrogen stoichiometric ratio and the phase transformation sequence are obtained. The results demonstrate that the initial decomposition temperature is dependent on experimental conditions, which occurs, respectively, at about 300 and 400 °C in a low vacuum condition and under a flowing helium atmosphere. During the decomposition process of TiH 2 in a low vacuum condition, the sample experiences a phase change process: δ(TiH 2 ) → δ (TiH x ) → δ(TiH x )+ β(TiH x ) → δ(TiH x )+ β(TiH x ) + α(Ti) → β(TiH x ) + α(Ti) → α(Ti) + β(Ti). This study offers a way to detect the structural information of hydrogen. A detailed discussion about the decomposition process of TiH 2 is given in this paper. (authors)

Technical Assistance Plan (TAP)

Science.gov (United States)

A Technical Assistance Plan (TAP) enables community groups to retain the services of an independent technical advisor and to provide resources for a community group to help inform other community members about site decisions.

Deposit of thin films of TiN, a-C, Ti/TiN/a-C by laser ablation; Deposito de peliculas delgadas de TiN, a-C, Ti/TiN/a-C por ablacion laser

Energy Technology Data Exchange (ETDEWEB)

Mejia, I.S.; Escobar A, L.; Camps, E.; Romero, S. [ININ, 52045 Ocoyoacac, Estado de mexico (Mexico); Muhl, S. [IIM, UNAM, A.P. 364, 01000 Mexico D.F. (Mexico)

2006-07-01

Thin films of titanium nitride (TiN), amorphous carbon (a-C), as well as bilayers of Ti/TiN/a-C were deposited by means of the laser ablation technique. It was investigated the effect that it has the laser fluence used to ablation the targets in the structure and mechanical properties of the TiN deposited films. The TiN obtained films have a preferential orientation in the direction (200). The results show that the hardness of this material is influenced by the laser fluence. It is observed that the hardness is increased in an approximately lineal way with the increment of the fluence up to 19 J/cm{sup 2}. The films of amorphous carbon present hardness of the order of 11.2 GPa. Likewise it was found that the multilayers of Ti/TiN/aC presented a bigger hardness that of its individual components. (Author)

The Role of Formal Education, Technical and Management Training on Information Systems (IS) Managers' Managerial Effectiveness as Perceived by Their Subordinates

Science.gov (United States)

Ligon, Jerry; Abdullah, ABM; Talukder, Majharul

2007-01-01

This study examined the relationship between Information Systems (IS) managers' formal education, level of technical and managerial training and their managerial effectiveness as perceived by their subordinates. The study finds that there is a strong positive relationship between the amount of technical training IS managers have received and their…

A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

International Nuclear Information System (INIS)

Li Jianing; Chen Chuanzhong; Squartini, Tiziano; He Qingshan

2010-01-01

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti 3 Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti 3 Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti 3 Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti 3 Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

Study of the preparation of Cu-TiC composites by reaction of soluble Ti and ball-milled carbon coating TiC

Science.gov (United States)

Xu, Xuexia; Li, Wenbin; Wang, Yong; Dong, Guozhen; Jing, Shangqian; Wang, Qing; Feng, Yanting; Fan, Xiaoliang; Ding, Haimin

2018-06-01

In this work, Cu-TiC composites have been successfully prepared by reaction of soluble Ti and carbon coating TiC. Firstly, the ball milling of graphite and TiC mixtures is used to obtain the carbon coating TiC which has fine size and improved reaction activity. After adding the ball milled carbon coating TiC into Cu-Ti melts, the soluble Ti will easily react with the carbon coating to form TiC. This process will also improve the wettability between Cu melts and TiC core. As a result, besides the TiC prepared by reaction of soluble Ti and carbon coating, the ball milled TiC will also be brought into the melts. Some of these ball-milled TiC particles will go on being coated by the formed TiC from the reaction of Ti and the coating carbon and left behind in the composites. However, most of TiC core will be further reacted with the excessive Ti and be transformed into the newly formed TiC with different stoichiometry. The results indicate that it is a feasible method to synthesize TiC in Cu melts by reaction of soluble Ti and ball-milled carbon coating TiC.

The martensitic transformation in Ti-rich TiNi shape memory alloys

International Nuclear Information System (INIS)

Lin, H.C.; Wu, S.K.; Lin, J.C.

1994-01-01

The martensitic (Ms) transformation temperatures and their ΔH values of Ti 51 Ni 49 and Ti 50.5 Ni 49.5 alloys are higher than those of equiatomic or Ni-rich TiNi alloys. The Ti-rich TiNi alloys exhibit good shape recovery in spite of a great deal of second phase Ti 2 Ni or Ti 4 Ni 2 O existing around B2 grain boundaries. The nearly identical transformation temperatures indicate that the absorbed oxygen in Ti-rich TiNi alloys may react with Ti 2 Ni particles, instead of the TiNi matrix, to form Ti 4 Ni 2 O. Martensite stabilization can be induced by cold rolling at room temperature. Thermal cycling can depress the transformation temperatures significantly, especially in the initial 20 cycles. The R-phase transformation can be promoted by both cold rolling and thermal cycling in Ti-rich TiNi alloys due to introduced dislocations depressing the Ms temperature. The strengthening effects of cold rolling and thermal cycling on the Ms temperature of Ti-rich TiNi alloys are found to follow the expression Ms = To - KΔσ y . The K values are affected by different strengthening processes and related to the as-annealed transformation temperatures. The higher the as-annealed Ms (or As), the larger the K value. (orig.)

Technical Network

CERN Multimedia

2007-01-01

In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

Multilayer TiC/TiN diffusion barrier films for copper

International Nuclear Information System (INIS)

Yoganand, S.N.; Raghuveer, M.S.; Jagannadham, K.; Wu, L.; Karoui, A.; Rozgonyi, G.

2002-01-01

TiC/TiN thin films deposited by reactive magnetron sputtering on Si (100) substrates were investigated by transmission electron microscopy for microstructure and by deep level transient spectroscopy (DLTS) for diffusion barrier against copper. TiN thin films deposited on Si substrates at a substrate temperature of 600 deg. C were textured, and TiC thin films deposited at the same temperature were polycrystalline. TiC/TiN multilayer films also showed the same characteristics with the formation of an additional interaction layer. The diffusion barrier characteristics of the TiC/TiN/Si were determined by DLTS and the results showed that the films completely prevented diffusion of copper into Si

The Influence of a TiN Film on the Electronic Contribution to the Thermal Conductivity of a TiC Film in a TiN-TiC Layer System

Science.gov (United States)

Jagannadham, K.

2018-01-01

TiC and TiN films were deposited by reactive magnetron sputtering on Si substrates. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) characterization of the microstructure and interface structure have been carried out and the stoichiometric composition of TiC is determined. Thermal conductivity and interface thermal conductance between different layers in the films are evaluated by the transient thermo reflectance (TTR) and three-omega (3- ω) methods. The results showed that the thermal conductivity of the TiC films increased with temperature. The thermal conductivity of TiC in the absence of TiN is dominated by phonon contribution. The electronic contribution to the thermal conductivity of TiC in the presence of TiN is found to be more significant. The interface thermal conductance of the TiC/TiN interface is much larger than that of interfaces at Au/TiC, TiC/Si, or TiN/Si. The interface thermal conductance between TiC and TiN is reduced by the layer formed as a result of interdiffusion.

Penetration resistance and ballistic-impact behavior of Ti/TiAl3 metal/intermetallic laminated composites (MILCs: A computational investigation

Directory of Open Access Journals (Sweden)

Jennifer S. Snipes

2016-06-01

Full Text Available A comprehensive computational engineering analysis is carried out in order to assess suitability of the Ti/TiAl3 metal/intermetallic laminated composites (MILCs for use in both structural and add-on armor applications. This class of composite materials consists of alternating sub-millimeter thick layers of Ti (the ductile and tough constituent and TiAl3 (the stiff and hard constituent. In recent years, this class of materials has been investigated for potential use in light-armor applications as a replacement for the traditional metallic or polymer-matrix composite materials. Within the computational analysis, an account is given to differing functional requirements for candidate materials when used in structural and add-on ballistic armor. The analysis employed is of a transient, nonlinear-dynamics, finite-element character, and the problem investigated involves normal impact (i.e. under zero obliquity angle of a Ti/TiAl3 MILC target plate, over a range of incident velocities, by a fragment simulating projectile (FSP. This type of analysis can provide more direct information regarding the ballistic limit of the subject armor material, as well as help with the identification of the nature and the efficacy of various FSP material-deformation/erosion and kinetic-energy absorption/dissipation phenomena and processes. The results obtained clearly revealed that Ti/TiAl3 MILCs are more suitable for use in add-on ballistic, than in structural armor applications.

Synthesis, microstructure and mechanical properties of Ti3SiC2-TiC composites pulse discharge sintered from Ti/Si/TiC powder mixture

International Nuclear Information System (INIS)

Tian Wubian; Sun Zhengming; Hashimoto, Hitoshi; Du Yulei

2009-01-01

Ti 3 SiC 2 -TiC composites with the volume fractions of TiC from 0 to 90% were fabricated by pulse discharge sintering (PDS) technique using Ti-Si-TiC as starting powders in the sintering temperature range of 1250-1400 deg. C. Phase content and microstructure of the synthesized samples were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The samples sintered at 1400 deg. C are almost fully dense for all compositions with relative density higher than 98%. The phase distribution in the synthesized samples is non-uniform. The Vickers hardness increases almost linearly with the volume fraction of TiC up to a value of 20.1 ± 1.4 GPa at 90 vol.% TiC. The flexural strength increases with the volume fraction of TiC to a maximum value of 655 ± 10 MPa at 50 vol.% TiC. The relationship between microstructure and mechanical properties is discussed.

Technical Knowledge and Skills Development in the Informal Sector in Kenya: The Case of Custom Tailors

Science.gov (United States)

Apunda, Edwinah Amondi; de Klerk, Helena M.; Ogina, Teresa

2017-01-01

Custom tailors working in the informal sector in Nairobi, Kenya, mainly acquire technical skills through undertaking traditional apprenticeships (TAs). However, most of these tailors are semi-skilled, produce low-quality products and are often poorer than their formally trained counterparts. This qualitative case study explores the aspects of…

Preparation and Characterization of TiO2 Nanostructure by TiCl4 Hydrolysis with Additive NaOH

Directory of Open Access Journals (Sweden)

Rashed Taleb Rasheed

2018-04-01

Full Text Available Titanium dioxide (TiO2 nanostructures were synthesized via the hydrolysis of TiCl4 in alcohol / water solution/with sodium hydroxide solution in the ice-bath (0-5 ◦C. The particles were char-acterized by using X-ray diffraction technique (XRD, spectroscopy of Ultra Violet-Visible (UV / Visible and infrared (FT-IR, atomic force microscope (AFM and scanning electron micro-scope (SEM analysis were used in order to gain information about the material, morphology, size and the shape of the particles

An overview of remedial action technical information support activities funded by the US Department of Energy's Office of Environmental Restoration

International Nuclear Information System (INIS)

Owen, P.T.

1990-01-01

In 1979 the US Department of Energy (DOE) established the Remedial Action Program Information Center (RAPIC) at the Oak Ridge National Laboratory (ORNL) to provide technical information support to the DOE's Remedial Action Programs, which comprise: Formerly Utilized Sites Remedial Action Program (FUSRAP), Surplus Facilities Management Program (SFMP), and Uranium Mill Tailings Remedial Action Program (UMTRAP). Specific information activities that RAPIC performs to support the DOE's programs include: maintaining a computerized bibliographic database containing approximately 7000 annotated references relevant to remediation work at radioactively contaminated sites; publishing an annual bibliography, Nuclear Facility Decommissioning and Site Remedial Actions, A Selected Bibliography, ORNL/EIS-154; maintaining a document repository and providing copies of requested publications; and performing manual and computerized searches of the technical literature. The most important RAPIC function is serving as a focal point for remedial action information. With these extensive resources at its command, RAPIC is in a unique position to provide a comprehensive information base to the remedial action and environmental restoration community

Technical report writing today

CERN Document Server

Riordan, Daniel G

2014-01-01

"Technical Report Writing Today" provides thorough coverage of technical writing basics, techniques, and applications. Through a practical focus with varied examples and exercises, students internalize the skills necessary to produce clear and effective documents and reports. Project worksheets help students organize their thoughts and prepare for assignments, and focus boxes highlight key information and recent developments in technical communication. Extensive individual and collaborative exercises expose students to different kinds of technical writing problems and solutions. Annotated student examples - more than 100 in all - illustrate different writing styles and approaches to problems. Numerous short and long examples throughout the text demonstrate solutions for handling writing assignments in current career situations. The four-color artwork in the chapter on creating visuals keeps pace with contemporary workplace capabilities. The Tenth Edition offers the latest information on using electronic resum...

First-Principles Study of the Polar TiC/Ti Interface

Institute of Scientific and Technical Information of China (English)

Limin LIU; Shaoqing WANG; Hengqiang YE

2003-01-01

The interface structure, work of adhesion, and bonding character of the polar TiC/Ti interface have been examined by the first-principles density functional plane-wave pseudopotential calculations. Both Ti- and C-terminated interfaces including six different interface structures were calculated, which present quite different features. For the Ti-terminated interface, the interfacial Ti-Ti bond has a strong metallic and weak covalent character; while for the C-terminated interface, the interfacial bond is a strong polar covalent interaction between the Ti-3d and C-2p orbital.The work of adhesion of C-terminated interface is nearly 9 J/m2 stronger than that of the Ti-terminated. It is found that each termination has relatively large work of adhesion, which is consistent with other polar interfaces.

The share of sales for secondary information in the sales for scientific and technical information in the Federal Republic of Germany

International Nuclear Information System (INIS)

Bernhardt, U.; Jungjohann, K.

1978-07-01

This final report of an empirical research about the expenditures and sales for Secondary Information (SI) as a share of Scientific and Technical Information (STI) in 1974 is furthermore concerned with: the quantity of SI and STI; the share of information free of charge; a specification for information products, individual information services and magnetic tape services; a differentiation for several areas in the market (institutions for information and documentation, libraries, publishers and privat users); the evaluation of the development for expenditures and sales till 1980. The methods of raising the relevant data comprised questionnaires and verbal interviews, case studies and the analysis of statistical literature. In the second phase of research questionnaires were sent to experts for a final evaluation of results. The important results are: The expenditures in the institutional sector and in libraries for SI in 1974 amount to 80 million DM and in the privat sector to about 117 million DM. The share of SI in STI amounts 8 percent. The sales for SI in the institutions for information and documentation reached 38 million DM. (orig.) [de

sup 4 sup 4 Ti atom counting for nuclear astrophysics

CERN Document Server

Hui, S K; Berkovits, D; Boaretto, E; Ghelberg, S; Hass, M; Hershkowitz, A; Navon, E

2000-01-01

The nuclide sup 4 sup 4 Ti (T sub 1 sub / sub 2 =59.2 yr) has recently become an important asset to nuclear astrophysics through the measurement of its cosmic radioactivity, yielding significant information on fresh sup 4 sup 4 Ti nucleosynthesis in supernovae. We propose to use AMS to determine the production rate of sup 4 sup 4 Ti by the main channel believed to be responsible for sup 4 sup 4 Ti astrophysical production, namely sup 4 sup 0 Ca(alpha,gamma). A preliminary experiment conducted at the Koffler 14UD Pelletron accelerator demonstrates a sensitivity of 1x10 sup - sup 1 sup 4 for the sup 4 sup 4 Ti/Ti ratio. The AMS detection was performed using sup 4 sup 4 Ti sup - ions sputtered from a TiO sub 2 sample, reducing considerably the sup 4 sup 4 Ca isobaric interference. The present limit corresponds effectively to sup 4 sup 4 Ti production with resonance strength in the range 10-100 meV for a one-day sup 4 sup 0 Ca(alpha,gamma) activation. Several such resonances are known to be responsible for sup 4 ...

A study on wear resistance and microcrack of the Ti{sub 3}Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

Energy Technology Data Exchange (ETDEWEB)

Li Jianing, E-mail: ljnljn1022@163.com [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Chen Chuanzhong [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China); Squartini, Tiziano [INFM-Department of Physics, Siena University, Siena 53100 (Italy); He Qingshan [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Department of Materials Science, Shandong University, Jing Shi Road 17923, Jinan 250061, Shandong (China)

2010-12-15

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti{sub 3}Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti{sub 3}Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti{sub 3}Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti{sub 3}Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.

Fretting wear behaviour of TiC/Ti(C,N)/TiN multi-layer coatings at elevated temperature in gross slip regime

International Nuclear Information System (INIS)

Liu Hanwei; Huang Kunpeng; Zhu Minhao; Zhou Zhongrong

2005-01-01

Tic/Ti(C,N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C,N)/TiN coatings are investigated and studied controversially from 25 degree C to 400 degree C in the gross slip regime. It shows that the temperature has great influence on the fretting wear in the gross slip regime for the 1Cr13 stainless steel but little for Ti/C/Ti(C,N)/TiN multi-layer coatings. With the temperature increasing, the friction coefficient and the wear volume of the 1Cr13 alloy decreases and the wear volume of TiC/Ti(C, N)/TiN multi-layer coatings is invariant. TiC/Ti(C,N)/TiN multi-layer coatings have better wear-resistant capability than the 1Cr13 stainless steel, but the wear volume of the substrate increases greatly because of the grain-abrasion resulted from hard debris when TiC/Ti(C,N)/TiN multi-layer coatings are ground off. (authors)

The challenge of contracting for technological information

Science.gov (United States)

Zeckhauser, Richard

1996-01-01

Contracting to provide technological information (TI) is a significant challenge. TI is an unusual commodity in five ways. (i) TI is difficult to count and value; conventional indicators, such as patents and citations, hardly indicate value. TI is often sold at different prices to different parties. (ii) To value TI, it may be necessary to “give away the secret.” This danger, despite nondisclosure agreements, inhibits efforts to market TI. (iii) To prove its value, TI is often bundled into complete products, such as a computer chip or pharmaceutical product. Efficient exchange, by contrast, would involve merely the raw information. (iv) Sellers’ superior knowledge about TI’s value make buyers wary of overpaying. (v) Inefficient contracts are often designed to secure rents from TI. For example, licensing agreements charge more than marginal cost. These contracting difficulties affect the way TI is produced, encouraging self-reliance. This should be an advantage to large firms. However, small research and development firms spend more per employee than large firms, and nonprofit universities are major producers. Networks of organizational relationships, particularly between universities and industry, are critical in transmitting TI. Implicit barter—money for guidance—is common. Property rights for TI are hard to establish. Patents, quite suitable for better mousetraps, are inadequate for an era when we design better mice. Much TI is not patented, and what is patented sets fuzzy demarcations. New organizational forms are a promising approach to contracting difficulties for TI. Webs of relationships, formal and informal, involving universities, start-up firms, corporate giants, and venture capitalists play a major role in facilitating the production and spread of TI. PMID:8917488

Tailoring ultrafine grained and dispersion-strengthened Ti 2 AlC/TiAl ...

Indian Academy of Sciences (India)

In situ Ti 2 AlC/TiAl composite was fabricated by hot-pressing method via the reaction system of Ti 3 AlC 2 and Ti-Al pre-alloyed powders at low temperature of 1150 ∘ C. The composite mainly consisted of TiAl, Ti 3 Al and Ti 2 AlC phases. Fine Ti 2 AlC particles were homogeneously distributed and dispersed in the matrix.

Structure, phase composition and microhardness of vacuum-arc multilayered Ti/Al, Ti/Cu, Ti/Fe, Ti/Zr nano-structures with different periods

Energy Technology Data Exchange (ETDEWEB)

Demchishin, A.V., E-mail: ademch@meta.ua [Institute of Problems in Material Science, NASU, Kiev (Ukraine); Gnilitskyi, I., E-mail: iaroslav.gnilitskyi@unimore.it [DISMI – Department of Sciences and Methods for Engineering, University of Modena and Reggio Emilia, Reggio Emilia (Italy); Orazi, L., E-mail: leonardo.orazi@unimore.it [DISMI – Department of Sciences and Methods for Engineering, University of Modena and Reggio Emilia, Reggio Emilia (Italy); Ascari, A., E-mail: a.ascari@unibo.it [DIN – Department of Industrial Engineering, University of Bologna, Bologna (Italy)

2015-07-01

Highlights: • Multilayer coatings of Ti/Fe, Ti/Al, Ti/Cu and Ti/Zr are generated. • Microstructure and morphology of the different systems are investigated. • XR diffraction analysis was performed to investigate phases composition. • Effects of inter metallic phases on microhardess are investigated. • Correlations between parameters and layer thickness are outlined. - Abstract: The microstructure, phase composition and microhardness of multilayered Ti/Al, Ti/Cu, Ti/Fe and Ti/Zr condensates produced on stainless steel substrates via vacuum-arc evaporation of pure metals were studied. The sublayer periods (Λ) were regulated in the range 80–850 nm by varying the vacuum discharge current and the duration of the successive depositions of metallic plasma onto the substrates while maintaining the total deposition time constant. The regularity of the obtained nanostructures was investigated by scanning and transmission electron microscopy while phase compositions were identified with X-ray diffraction (XRD) analysis in order to evidence the presence of interdiffusion and the amount of intermetallics. Condensates cross sections were mechanically characterized by means of microhardness tests. Measurements were correlated to the periods and to the presence of intermetallics.

Structure, phase composition and microhardness of vacuum-arc multilayered Ti/Al, Ti/Cu, Ti/Fe, Ti/Zr nano-structures with different periods

International Nuclear Information System (INIS)

Demchishin, A.V.; Gnilitskyi, I.; Orazi, L.; Ascari, A.

2015-01-01

Highlights: • Multilayer coatings of Ti/Fe, Ti/Al, Ti/Cu and Ti/Zr are generated. • Microstructure and morphology of the different systems are investigated. • XR diffraction analysis was performed to investigate phases composition. • Effects of inter metallic phases on microhardess are investigated. • Correlations between parameters and layer thickness are outlined. - Abstract: The microstructure, phase composition and microhardness of multilayered Ti/Al, Ti/Cu, Ti/Fe and Ti/Zr condensates produced on stainless steel substrates via vacuum-arc evaporation of pure metals were studied. The sublayer periods (Λ) were regulated in the range 80–850 nm by varying the vacuum discharge current and the duration of the successive depositions of metallic plasma onto the substrates while maintaining the total deposition time constant. The regularity of the obtained nanostructures was investigated by scanning and transmission electron microscopy while phase compositions were identified with X-ray diffraction (XRD) analysis in order to evidence the presence of interdiffusion and the amount of intermetallics. Condensates cross sections were mechanically characterized by means of microhardness tests. Measurements were correlated to the periods and to the presence of intermetallics

Technical Report Writing Today

DEFF Research Database (Denmark)

Riordan, Daniel G.

2014-01-01

Section 1: Technical Communication Basics (8 chapters on tech com, audiences, tech com process, tech com style, researching, designing pages, using visual aids, describing). Section 2: Technical Communication Applications (7 chapters on sets of instructions, informal reports and email, developing...

Preparation and solar-light photocatalytic activity of TiO2 composites: TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite

Science.gov (United States)

Li, Y.; Li, S. G.; Wang, J.; Li, Y.; Ma, C. H.; Zhang, L.

2014-12-01

Three TiO2 loaded composites, TiO2/kaolin, TiO2/diatomite, and TiO2/zeolite, were prepared in order to improve the solar-light photocatalytic activity of TiO2. The results showed that the photocatalytic activity could obviously be enhanced by loading appropriate amount of inorganic mineral materials. Meanwhile, TiO2 content, heat-treatment temperature and heat-treatment time on the photocatalytic activity were reviewed. Otherwise, the effect of solar light irradiation time and dye concentration on the photocatalytic degradation of Acid Red B was investigated. Furthermore, the degradation mechanism and adsorption process were also discussed.

Photoelectrocatalytic property of microporous Pt-TiO2/Ti electrodes

International Nuclear Information System (INIS)

Hung, Chung-Hsuang; Wu, Kee-Rong; Yeh, Chung-Wei; Sun, Jui-Ching; Hsu, Chuan-Jen

2013-01-01

This study investigates the photoelectrocatalytic (PEC) property of microporous WO 3 -loaded TiO 2 /Ti layer, prepared via micro-arc oxidation (MAO) of Ti plate, followed by sputtering deposition of a thin Pt layer as a Pt-TiO 2 /Ti electrode. The WO 3 -loaded TiO 2 layer which is associated with a more acidic surface forms many local electrochemical cells on its micro-pores immersed in cationic dye solution. The electrocatalytic (EC) reactions can take place in the local cells by the applied electrons. A low resistivity that is accomplished by MAO technique and by platinization offers an easy path for the electron motions in the Pt-TiO 2 /Ti electrode. All these features make the EC oxidation of aqueous dye pollutants practically feasible without using counter electrodes and supporting electrolytes. Our experiments demonstrate that, under PEC condition, the Pt-TiO 2 /Ti shows the highest degradation rate constant of 0.83 h − 1 at an applied bias of 1.0 V and exhibits significantly high PEC and EC oxidation activities at a low applied bias of 0.25 V. This is attributable to high anodic currents generated in the Pt-TiO 2 /Ti even at low bias. The modified microporous electrodes conclusively reveal a very interesting EC property as a two double-sided device that functions the PEC and EC oxidation simultaneously without a need of supporting electrolyte and expensive Pt cathode. - Highlights: ► Pt-TiO 2 /Ti exhibits enhanced photoelectrocatalytic (PEC) activity at low applied bias. ► The proposed device uses low applied bias (< 1.0 V) with no explicit cathode. ► PEC oxidation can be performed without supporting electrolyte and Pt cathode

Electron densities and chemical bonding in TiC, TiN and TiO derived from energy band calculations

International Nuclear Information System (INIS)

Blaha, P.

1983-10-01

It was the aim of this paper to describe the chemical bonding of TiC, TiN and TiO by means of energy bands and electron densities. Using the respective potentials we have calculated the bandstructure of a finer k-grid with the linearized APW method to obtain accurate densities of states (DOS). These DOS wer partitioned into local partial contributions and the metal d DOS were further decomposed into tsub(2g) and esub(g) symmetry components in order to additionally characterize bonding. The electron densities corresponding to the occupied valence states are obtained from the LAPW calculations. They provide further insight into characteristic trends in the series from TiC to TiO: around the nonmetal site the density shows increasing localisation; around the metal site the deviation from spherical symmetry changes from esub(g) to tsub(2g). Electron density plots of characteristic band states allow to describe different types of bonding occurring in these systems. For TiC and TiN recent measurements of the electron densities exist for samples of TiCsub(0.94) and TiNsub(0.99), where defects cause static displacements of the Ti atoms. If this effect can be compensated by an atomic model one hopefully can extrapolate to stoichiometric composition. This procedure allows a comparison with structure factors derived from theoretical electron densities. The agreement for TiN is very good. For TiC the extrapolated data agree in terms of the deviations from spherical symmetry near the Ti site with the LAPW data, but the densities around both atoms are more localized than in theory. An explanation could be: a) the defects affect the electronic structure in TiCsub(0.94) with respect to TiCsub(1.0): b) the applied atomic model does not properly extrapolate to stoichiometry, because parameters of this model correlate or become unphysical. (Author)

TEM characterization of a Cr/Ti/TiC graded interlayer for magnetron-sputtered TiC/a-C:H nanocomposite coatings

International Nuclear Information System (INIS)

Galvan, D.; Pei, Y.T.; De Hosson, J.Th.M.

2005-01-01

A TiC/a-C:H nanocomposite coating is deposited on top of a Cr/Ti/TiC graded interlayer. Cross-section transmission electron microscopy is employed to investigate the detailed structure of the interlayer and the coating. Five different phases are formed as a consequence of the compositional gradient within the interlayer: pure Cr, a solid solution of Ti in Cr, a Ti/Cr amorphous/nanocrystalline phase, α-Ti and TiC. Solid state amorphization occurs during the interlayer deposition to give a dispersion of TiCr β-phase nanocrystals in an amorphous matrix. The TiC phase is textured and contains numerous stacking faults as a result of the growth in under-stoichiometric carbon concentration. C-enriched columnar boundaries are present within the coating, originating from the TiC column boundaries of the interlayer. The work indicates that an interlayer of amorphous/nanocrystalline Ti/Cr phase would reduce the presence of growth defects such as columnar boundaries within nanocomposite TiC/a-C:H coatings

Stability of tritium permeation prevention barrier with TiC and TiN + TiC coating

International Nuclear Information System (INIS)

Shan Changqi; Chen Qingwang; Dai Shaoxia; Jiang Weisheng

1999-01-01

The stability of tritium permeation prevention barrier of 316L stainless steel with coating TiC and TiN + TiC under the conditions of very large thermal gradient, thermal cycling and plasma irradiation is researched. The research includes two aspects: one is the study on the stability resisting H + plasma irradiation; another is on the ability of two coating materials when they are used in long term under the condition of very large thermal gradient and cycling. The results show that TiC and TiN + TiC composite coating materials, after chemical heat treatment and forming tritium permeation prevention barrier, can resist H + ion irradiation, and also can resist very large thermal gradient and thermal cycling. The long time experiments show that tritium permeation prevention barrier of those coating materials is stable when they are used in long term

Evaluated (n,p) cross sections of 46Ti, 47Ti and 48Ti

International Nuclear Information System (INIS)

Philis, C.; Bersillon, O.; Smith, D.; Smith, A.

1977-01-01

Microscopic evaluated neutron cross sections for the reactions 46 Ti(n;p) 46 Sc, 47 Ti(n;p) 47 Sc and 48 Ti(n;p) 48 Sc are obtained from threshold (or zero energy) to 20 MeV. The results are presented in graphical and numerical (ENDF format) form. The microscopic evaluated cross sections are compared with measured fission-spectrum-averaged values

77 FR 3284 - Comment Request for Information Collection for the H-1B Technical Skills Training (H-1B) and the...

Science.gov (United States)

2012-01-23

... concerning the collection of data about H-1B Technical Skills Training (H-1B) [SGA/DFA PY-10-13] and H-1B... DEPARTMENT OF LABOR Comment Request for Information Collection for the H-1B Technical Skills Training (H-1B) and the H-1B Jobs and Innovation Accelerator Challenge (JIAC) Grant Programs, New...

In situ preparation of (TiB + TiC + Nd2O3)/Ti composites by powder metallurgy

International Nuclear Information System (INIS)

Lu Junqiang; Qin Jining; Lu Weijie; Liu Yang; Gu Jiajun; Zhang Di

2009-01-01

Titanium matrix composites reinforced with multiple ceramic particulates TiB, TiC and Nd 2 O 3 were prepared by powder metallurgy utilizing the chemical reactions among Ti, B 4 C, NdB 6 and oxygen in Ti powder. The thermodynamic feasibility of the in situ reaction has been calculated. The phases were identified by X-ray diffraction (XRD). The result shows that multiple ceramic phases TiB, TiC and Nd 2 O 3 particulates have been synthesized. The microstructures were examined by means of optical microscopy (OM), scanning electron microscopy (SEM), backscattered electron microscopy and transmission electron microscope (TEM). The results show that the reinforcements are distributed uniformly in the matrix alloy and grow in different shapes. TiB grows in needle shape; TiC and Nd 2 O 3 grow in equiaxed or near-equiaxed shapes. The addition of NdB 6 is beneficial to grain refinement, grain-boundary purification and porosity reduction

Nitrogen implantation of Ti and Ti+Al films deposited on tool steel

International Nuclear Information System (INIS)

Huang, C.-T.; Duh, J.-G.

1995-01-01

Titanium and aluminum thin films were deposited onto A2 steel by rf magnetron sputtering with various Al contents. The coated assembly was then implanted with nitrogen ions at 92 kV and 1 mA for 4.5 h. The thickness of the implanted Ti and Ti+Al films deposited for 1 h was around 0.4-0.5 μm. With the aid of X-ray diffraction by the grazing-incidence technique, secondary ion mass spectrum (SIMS) and X-ray photoelectron spectroscopy (XPS), the titanium oxide and titanium nitride were identified on the top and inner surface in the implanted Ti film. For Ti+Al films after nitrogen implantation, Ti 3 O 5 was formed on the top surface beneath which is a (Ti, Al) N solid solution. There was Ti 2 N compound formed in the implanted Ti film, while only a minor amount of Ti 2 N phase was observed in the inner region in the implanted Ti+Al film. The nitrogen distribution was flattened and spread in the implanted Ti film, while a concentration gradient was observed in the Ti+Al film after implantation. The measured surface hardness of implanted Ti film was higher than those of Ti+Al films and the hardness of implanted Ti+39%Al film was enhanced as compared to the Ti+50%Al film. (Author)

Evolution process of the synthesis of TiC in the Cu-Ti-C system

International Nuclear Information System (INIS)

Liang, Y.H.; Wang, H.Y.; Yang, Y.F.; Wang, Y.Y.; Jiang, Q.C.

2008-01-01

The evolution process of TiC formation in the 20 wt.% Cu-Ti-C powder mixtures was studied by using differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The Ti x Cu y compounds (Ti 2 Cu, TiCu, Ti 3 Cu 4 and TiCu 4 ) formed initially via solid-state diffusion reactions between Cu and Ti particles; and then Ti 2 Cu and TiCu can form a Cu-Ti eutectic liquids at about 1233 K. The unreacted Ti and C particles dissolved into the Cu-Ti liquids and led to the formation of Cu-Ti-C ternary liquids; subsequently, TiC particulates precipitated out of the saturated liquids. At the same time, also the formation of Ti 2 Cu occurred at the interface between the Cu-Ti liquids and the unreacted Ti particles. As the temperature increased further, the Ti 2 Cu melted and more Cu-Ti liquids formed; and then C particles continuously dissolved into the Cu-Ti-C liquids and TiC particulates gradually precipitated out of the saturated liquids

Fabrication and Characterization of New Ti-TiO2-Al and Ti-TiO2--Pt Tunnel Diodes

Directory of Open Access Journals (Sweden)

Yaksh Rawal

2012-01-01

Full Text Available Remotely empowered wireless sensor networks use different energy resources including photovoltaic solar cells, wireless power transmission, and batteries. As another option the electromagnetic energy available in the ambient can be harvested to power these remote sensors. This is particularly valuable if it is desirable to harvest the ambient energy available in the wide range of electromagnetic spectrum. This has motivated the research for developing energy harvesting devices which can absorb this energy and produce a DC voltage. Rectenna, an antenna coupled with a rectifier, is the main component used for absorbing electromagnetic radiation at GHz and THz frequencies. Rectifying MIM tunnel diodes are able to operate at tens and hundreds of GHz frequency. As the preliminary steps towards development of high-frequency rectifiers, this paper presents fabrication and DC characterization of two new MIM diodes, Ti-TiO2-Al and Ti-TiO2-Pt. G-V analysis of the fabricated diodes verifies tunneling. Brinkman-Dynes-Rowell model is used to extract oxide thickness of which the derived value is around 9 nm. Ti-TiO2-Pt diode exhibits rectification ratio of 15 at 0.495 V, which is more than rectification ratio reported in earlier works.

TiC/Ti3SiC2复合材料的制备及其性能研究%Preparation and properties of TiC/Ti3SiC2 composites

Institute of Scientific and Technical Information of China (English)

贾换; 尹洪峰; 袁蝴蝶; 杨祎诺

2012-01-01

以粉末Ti,Si,TiC和炭黑为原料,采用反应热压烧结法制备TiC/Ti3SiC2复合材料.借助XRD和SEM研究TiC含量对TiC/Ti3SiC2复合材料相组成、显微结构及力学特性的影响.结果表明:通过热压烧结可以得到致密度较高的TiC/Ti3SiC2复合材料；引入TiC可以促进Ti3SiC2的生成,当引入TiC的质量分数达30％,TiC/Ti3SiC2复合材料的弯曲强度和断裂韧性分别为406.9 MPa,3.7 MPa·m1/2；复合材料中Ti3SiC2相以穿晶断裂为主,TiC晶粒易产生拔出.%TiC/Ti3SiC2 composites were fabricated by reactive hot pressing sintering method using the mixture powder of Ti, Si, C and TiC as raw material. The effect of TiC content on phase composition, microstructure and mechanical properties of TiC/Ti3SiC2 composites was investigated by X-ray diffraction and scanning electron microscopy. The results demonstrate that dense TiC/ Ti3SiC2 composites can be obtained by hot pressing. The addition of TiC into composites can enhance the formation of TisSiC2. When the additional content of TiC reaches 30% (mass fraction) , the flexural strength and fracture toughness of TiC/Ti3SiC2 composite are 406.9 MPa and 3.7 MPa·m-2, respectively. Ti3SiC2 phase displays intergranular fracture and TiC grain pulls out from Ti3SiC2 matrix when TiC/Ti3SiC2 composite fractures.

Controllable hydrothermal synthesis of rutile TiO2 hollow nanorod arrays on TiCl4 pretreated Ti foil for DSSC application

International Nuclear Information System (INIS)

Xi, Min; Zhang, Yulan; Long, Lizhen; Li, Xinjun

2014-01-01

Rutile TiO 2 nanorod arrays (TNRs) were achieved by hydrothermal process on TiCl 4 pretreated Ti foil. Subsequently, TNRs were hydrothermally etched in HCl solution to form hollow TiO 2 nanorod arrays (H-TNRs). The TiCl 4 pretreatment plays key roles in enhancement of Ti foil corrosion resistance ability and crystal nucleation introduction for TNRs growth. TNRs with desired morphology can be obtained by controlling TiCl 4 concentration and the amount of tetrabutyl titanate (TTB) accordingly. TNRs with the length of ∼1.5 μm and diameter of ∼200 nm, obtained on 0.15 M TiCl 4 pretreated Ti foil with 0.6 mL TTB, exhibits relatively higher photocurrent. The increased pore volume of the H-TNRs has contributed to the increased surface area which is benefit for Dye-Sensitized Solar Cells (DSSC) application. And the 180 °C-H-TNRs photoanode obtained from the 0.15-TiCl 4 -TNRs sample demonstrated 128.9% enhancement of photoelectric efficiency of DSSC compared to that of the original TNR photoanode. - Graphical abstract: Rutile hollow TiO 2 nanorod array photoanode obtained from original TiO 2 nanorod array photoanode by hydrothermal etching demonstrates enhanced photoelectric efficiency of DSSC. - Highlights: • TiO 2 nanorods are prepared via hydrothermal process on TiCl 4 -pretreated Ti foil. • Hollow TiO 2 nanorods are obtained by hydrothermal etching of TiO 2 nanorods. • TiCl 4 pretreatment plays a key role in protecting Ti foil from chemical corrosion. • Hollow TiO 2 nanorods photoanode shows enhanced photoelectric efficiency for DSSC

Technical rules in law

Energy Technology Data Exchange (ETDEWEB)

Debelius, J

1978-08-01

An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself.

Technical rules in law

International Nuclear Information System (INIS)

Debelius, J.

1978-01-01

An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself. (orig.) [de

Phase Constituents and Microstructure of Ti3Al/Fe3Al + TiN/TiB2 Composite Coating on Titanium Alloy

Science.gov (United States)

Li, Jianing; Chen, Chuanzhong; Zhang, Cuifang

Laser cladding of the Fe3Al + B4C/TiN + Al2O3 pre-placed powders on the Ti-6Al-4V alloy can form the Ti3Al/Fe3Al + TiN/TiB2 composite coating, which improved the wear resistance of the Ti-6Al-4V alloy surface. In this study, the Ti3Al/Fe3Al + TiN/TiB2 composite coating has been researched by means of X-ray diffraction and scanning electron microscope. It was found that during the laser cladding process, Al2O3 can react with TiB2, leading to the formations of Ti3Al and B. This principle can be used to improve the Fe3Al + B4C/TiN laser-cladded coating on the Ti-6Al-4V alloy. Furthermore, during the cladding process, C consumed the oxygen in Fe3Al + B4C /TiN + Al2O3 molten pool, which retarded the productions of the redundant metal oxides.

The design, fabrication, and photocatalytic utility of nanostructured semiconductors: focus on TiO2-based nanostructures

Science.gov (United States)

Banerjee, Arghya Narayan

2011-01-01

Recent advances in basic fabrication techniques of TiO2-based nanomaterials such as nanoparticles, nanowires, nanoplatelets, and both physical- and solution-based techniques have been adopted by various research groups around the world. Our research focus has been mainly on various deposition parameters used for fabricating nanostructured materials, including TiO2-organic/inorganic nanocomposite materials. Technically, TiO2 shows relatively high reactivity under ultraviolet light, the energy of which exceeds the band gap of TiO2. The development of photocatalysts exhibiting high reactivity under visible light allows the main part of the solar spectrum to be used. Visible light-activated TiO2 could be prepared by doping or sensitizing. As far as doping of TiO2 is concerned, in obtaining tailored material with improved properties, metal and nonmetal doping has been performed in the context of improved photoactivity. Nonmetal doping seems to be more promising than metal doping. TiO2 represents an effective photocatalyst for water and air purification and for self-cleaning surfaces. Additionally, it can be used as an antibacterial agent because of its strong oxidation activity and superhydrophilicity. Therefore, applications of TiO2 in terms of photocatalytic activities are discussed here. The basic mechanisms of the photoactivities of TiO2 and nanostructures are considered alongside band structure engineering and surface modification in nanostructured TiO2 in the context of doping. The article reviews the basic structural, optical, and electrical properties of TiO2, followed by detailed fabrication techniques of 0-, 1-, and quasi-2-dimensional TiO2 nanomaterials. Applications and future directions of nanostructured TiO2 are considered in the context of various photoinduced phenomena such as hydrogen production, electricity generation via dye-sensitized solar cells, photokilling and self-cleaning effect, photo-oxidation of organic pollutant, wastewater management, and

PHASE CONSTITUENTS AND MICROSTRUCTURE OF Ti3Al/Fe3Al + TiN/TiB2 COMPOSITE COATING ON TITANIUM ALLOY

OpenAIRE

JIANING LI; CHUANZHONG CHEN; CUIFANG ZHANG

2011-01-01

Laser cladding of the Fe3Al + B4C/TiN + Al2O3 pre-placed powders on the Ti-6Al-4V alloy can form the Ti3Al/Fe3Al + TiN/TiB2 composite coating, which improved the wear resistance of the Ti-6Al-4V alloy surface. In this study, the Ti3Al/Fe3Al + TiN/TiB2 composite coating has been researched by means of X-ray diffraction and scanning electron microscope. It was found that during the laser cladding process, Al2O3 can react with TiB2, leading to the formations of Ti3Al and B. This principle can be...

CAISSE (Computer Aided Information System on Solar Energy) technical manual

Energy Technology Data Exchange (ETDEWEB)

Cantelon, P E; Beinhauer, F W

1979-01-01

The Computer Aided Information System on Solar Energy (CAISSE) was developed to provide the general public with information on solar energy and its potential uses and costs for domestic consumption. CAISSE is an interactive computing system which illustrates solar heating concepts through the use of 35 mm slides, text displays on a screen and a printed report. The user communicates with the computer by responding to questions about his home and heating requirements through a touch sensitive screen. The CAISSE system contains a solar heating simulation model which calculates the heating load capable of being supplied by a solar heating system and uses this information to illustrate installation costs, fuel savings and a 20 year life-cycle analysis of cost and benefits. The system contains several sets of radiation and weather data for Canada and USA. The selection of one of four collector models is based upon the requirements input during the computer session. Optimistic and pessimistic fuel cost forecasts are made for oil, natural gas, electricity, or propane; and the forecasted fuel cost is made the basis of the life cycle cost evaluation for the solar heating application chosen. This manual is organized so that each section describes one major aspect of the use of solar energy systems to provide energy for domestic consumption. The sources of data and technical information and the method of incorporating them into the CAISSE display system are described in the same order as the computer processing. Each section concludes with a list of future developments that could be included to make CAISSE outputs more regionally specific and more useful to designers. 19 refs., 1 tab.

The dynamics of TiN{sub x} (x = 1–3) admolecule interlayer and intralayer transport on TiN/TiN(001) islands

Energy Technology Data Exchange (ETDEWEB)

Edström, D., E-mail: daned@ifm.liu.se [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Sangiovanni, D.G.; Hultman, L. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Petrov, I.; Greene, J.E. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Frederick Seitz Materials Research Laboratory and the Materials Science Department, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Chirita, V. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden)

2015-08-31

It has been shown both experimentally and by density functional theory calculations that the primary diffusing species during the epitaxial growth of TiN/TiN(001) are Ti and N adatoms together with TiN{sub x} complexes (x = 1, 2, 3), in which the dominant N-containing admolecule species depends upon the incident N/Ti flux ratio. Here, we employ classical molecular dynamics (CMD) simulations to probe the dynamics of TiN{sub x} (x = 1–3) admolecules on 8 × 8 atom square, single-atom-high TiN islands on TiN(001), as well as pathways for descent over island edges. The simulations are carried out at 1000 K, a reasonable epitaxial growth temperature. We find that despite their lower mobility on infinite TiN(001) terraces, both TiN and TiN{sub 2} admolecules funnel toward descending steps and are incorporated into island edges more rapidly than Ti adatoms. On islands, TiN diffuses primarily via concerted translations, but rotation is the preferred diffusion mechanism on infinite terraces. TiN{sub 2} migration is initiated primarily by rotation about one of the N admolecule atoms anchored at an epitaxial site. TiN admolecules descend from islands by direct hopping over edges and by edge exchange reactions, while TiN{sub 2} trimers descend exclusively by hopping. In contrast, TiN{sub 3} admolecules are essentially stationary and serve as initiators for local island growth. Ti adatoms are the fastest diffusing species on infinite TiN(001) terraces, but on small TiN/TiN(001) islands, TiN dimers provide more efficient mass transport. The overall results reveal the effect of the N/Ti precursor flux ratio on TiN(001) surface morphological evolution and growth modes. - Highlights: • Classical MD is used to model TiN{sub x} admolecule dynamics on TiN/TiN(001) islands. • TiN{sub x} admolecules descend from islands by both direct hopping and exchange reactions. • TiN and TiN{sub 2} exhibit surprisingly high diffusivities on TiN/TiN(001) islands. • TiN{sub 3} tetramers are

Studies on UV/NaOCl/TiO2/Sep photocatalysed degradation of Reactive Red 195.

Science.gov (United States)

Karaoğlu, M Hamdi; Uğurlu, Mehmet

2010-02-15

The photocatalytic degradation of Reactive Red 195 (RR195) has been investigated in aqueous suspensions by using ultraviolet (UV), sodium hypochlorite (NaOCl) and TiO(2)/Sep nanoparticles together. To get the TiO(2)/Sep nanoparticle, the nanocrystalline TiO(2) anatase phase on sepiolite was obtained using a sufficient thermal treatment by gradually increasing the temperature from 300, 400 and 500 degrees C for 3h. Then, TiO(2)/Sep materials were characterized using different spectral and technical structural analyses with scanning electron microscopy (SEM) and X-ray diffraction (XRD). The influence of pH, catalyst amount, oxidant and initial dye concentration was investigated in all the experiments. Maximum colour and chemical oxygen demand (COD) removal were 99.9% and 78% respectively, at a dye concentration of 250 mg L(-1), NaOCl dosage of 50.37 mM, 0.1 g L(-1) weight of TiO(2)/Sep and pH of 5.45 in 3h. In addition, the pseudo-first order model was applied and r(2) values were noted from 0.92 to 0.99.

LHC Availability 2017: Technical Stop 1 to Technical Stop 2

CERN Document Server

Todd, Benjamin; Apollonio, Andrea; Walsh, David John; CERN. Geneva. ATS Department

2017-01-01

This document summarises the LHC machine availability for the period of Technical Stop 1 (TS1) to Technical Stop 2 (TS2) in 2017. This period was dedicated to proton physics with a bunch spacing of 25ns. This note has been produced and ratified by the Availability Working Group which has complied fault information for the period in question using the Accelerator Fault Tracker.

Development of a Low-Cost TiO2/CuO/Cu Solar Cell by using Combined Spraying and Electroplating Method

Directory of Open Access Journals (Sweden)

Mamat Rokhmat

2018-03-01

Full Text Available A simple method is proposed to develop a low-cost TiO2/CuO/Cu based solar cell. The cell is made by employing a lower grade (technical grade of TiO2 as the active material. CuO powder is synthesized using a wet chemical method and mixed with TiO2 powder to give impurity to the TiO2. A layer of TiO2/CuO is then deposited onto fluorin-doped tin oxide (FTO by spraying. Copper particles are grown on the spaces between the TiO2 and/or CuO particles by electroplating for more feasible electron migration. The TiO2/CuO/Cu solar cell is finalized by sandwiching a polymer electrolyte between the film and the counter electrode. Current-voltage measurement was performed for various parameters, such as the molarity of NaOH for producing CuO particles, the weight ratio of CuO over TiO2, and the current in the electroplating process. A highest efficiency of 1.40% and a fill factor of 0.37 were achieved by using this combined spray and electroplating method.

Technical Perspective on Using Information Demand Pattern in a Collaborative Recommendation System for Improving E-Mail Communication

Directory of Open Access Journals (Sweden)

Dirk Stamer

2015-04-01

Full Text Available Today e-mail communication information is widely used in organizations to distribute information. The increasing volume of received e-mails hinders an efficient work. It becomes more and more difficult to identify relevant e-mails inside this enormous volume of information. This work presents a solution in a multi-user environment by improving an established e-mail client extension based on information demand pattern with a recommendation system. The contributions of this work are (1 the concept and implementation of the solution for a single-user environment using information demand pattern, (2 the concept and architecture to use the solution in a multi-user environment (3 a detailed technical description about the proposed solutions.

Study of preparation of TiB2 by TiC in Al melts

International Nuclear Information System (INIS)

Ding Haimin; Liu Xiangfa; Nie Jinfeng

2012-01-01

TiB 2 particles are prepared by TiC in Al melts and the characteristics of them are studied. It is found that TiC particles are unstable when boron exists in Al melts with high temperature and will transform to TiB 2 and Al 4 C 3 . Most of the synthesized TiB 2 particles are regular hexagonal prisms with submicron size. The diameter of the undersurfaces of these prisms is ranging from 200 nm to 1 μm and the height is ranging from 100 nm to 300 nm. It is considered that controlling the transformation from TiC to TiB 2 is an effective method to prepare small and uniform TiB 2 particles. - Highlights: ► TiC can easily transform into TiB 2 in Al melts. ► TiB 2 formed by TiC will grow into regular hexagonal prisms with submicron size. ► Controlling the transformation from TiC to TiB 2 is an effective method to prepare small and uniform TiB 2 particles.

Value of information in natural resource management: technical developments and application to pink-footed geese

Science.gov (United States)

Williams, Byron K.; Johnson, Fred A.

2015-01-01

The “value of information” (VOI) is a generic term for the increase in value resulting from better information to guide management, or alternatively, the value foregone under uncertainty about the impacts of management (Yokota and Thompson, Medical Decision Making 2004;24: 287). The value of information can be characterized in terms of several metrics, including the expected value of perfect information and the expected value of partial information. We extend the technical framework for the value of information by further developing the relationship between value metrics for partial and perfect information and describing patterns of their performance. We use two different expressions for the expected value of partial information to highlight its relationship to the expected value of perfect information. We also develop the expected value of partial information for hierarchical uncertainties. We highlight patterns in the value of information for the Svalbard population of the pink-footed goose (Anser brachyrhynchus), a population that is subject to uncertainty in both reproduction and survival functions. The framework for valuing information is seen as having widespread potential in resource decision making, and serves as a motivation for resource monitoring, assessment, and collaboration.

Final Technical Report of the project "Controlling Quantum Information by Quantum Correlations"

Energy Technology Data Exchange (ETDEWEB)

Girolami, Davide [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-17

The report describes hypotheses, aims, methods and results of the project 20170675PRD2, “Controlling Quantum Information by Quantum Correlations”, which has been run from July 31, 2017 to January 7, 2018. The technical work has been performed by Director’s Fellow Davide Girolami of the T-4 Division, Physics of Condensed Matter and Complex Systems, under the supervision of Wojciech Zurek (T-4), Lukasz Cincio (T-4), and Marcus Daniels (CCS-7). The project ended as Davide Girolami has been converted to J. R. Oppenheimer Fellow to work on the project 20180702PRD1, “Optimal Control of Quantum Machines”, started on January 8, 2018.

Chemical bath deposited rutile TiO{sub 2} compact layer toward efficient planar heterojunction perovskite solar cells

Energy Technology Data Exchange (ETDEWEB)

Liang, Chao, E-mail: lc401997413@qq.com [State Centre for International Cooperation on Designer Low-Carbon and Environmental Material (SCICDLCEM), School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Wu, Zhenhua, E-mail: 80116243@qq.com [Henan Information Engineering School, Zhengzhou 450000 (China); Li, Pengwei, E-mail: pengweili001@126.com [State Centre for International Cooperation on Designer Low-Carbon and Environmental Material (SCICDLCEM), School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Fan, Jiajie, E-mail: fanjiajie@zzu.edu.cn [State Centre for International Cooperation on Designer Low-Carbon and Environmental Material (SCICDLCEM), School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Zhang, Yiqiang, E-mail: yqzhang@zzu.edu.cn [State Centre for International Cooperation on Designer Low-Carbon and Environmental Material (SCICDLCEM), School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China); Shao, Guosheng, E-mail: gsshao@zzu.edu.cn [State Centre for International Cooperation on Designer Low-Carbon and Environmental Material (SCICDLCEM), School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001 (China)

2017-01-01

Highlights: • Rutile TiO{sub 2} thin film can be grown on FTO substrate below 100 °C. • 200 mM TiCl{sub 4} precursor solution results in the best PSC performance. • UV/O{sub 3} treatment can reduce the carrier recombination effectively. • Over 12% power conversion efficiency can be achieved for PSCs. - Abstract: TiO{sub 2} is a best choice of electron transport layers in perovskite solar cells, due to its high electron mobility and stability. However, traditional TiO{sub 2} processing method requires rather high annealing temperature (>500 °C), preventing it from application to flexible devices. Here, we show that TiO{sub 2} thin films can be synthesized via chemical bath deposition below 100 °C. Typically, a compact layer of rutile TiO{sub 2} is deposited onto fluorine-doped tin oxide (FTO) coated substrates, in an aqueous TiCl{sub 4} solution at 70 °C. Through the optimization of precursor concentration and ultraviolet-ozone surface modification, over 12% power conversion efficiency can be achieved for CH{sub 3}NH{sub 3}PbI{sub 3} based perovskite solar cells. These findings offer a potential low-temperature technical solution in using TiO{sub 2} thin film as an effective transport layer for flexible perovskite solar cells.

A thermodynamic evaluation of the Ti-Mo-C system

International Nuclear Information System (INIS)

Shim, J.H.; Oh, C.S.; Lee, D.N.

1996-01-01

A thermodynamic assessment of the Ti-Mo-C system has been made, employing a two-sublattice regular solution model for the solid solution and carbide phases and an ordinary subregular solution model for the liquid phase. A set of thermodynamic parameters describing the Gibbs energy of each individual phase in the Ti-Mo-C as well as the Ti-Mo systems was evaluated from thermochemical and phase equilibria information available in the literature through a computer-aided optimization procedure called the CALPHAD method. The comparison between the calculated and experimental results was made and practically important phase diagrams are also presented

Microstructure and Mechanical Properties of Ti-6Al-4V Fabricated by Selective Laser Melting of Powder Produced by Granulation-Sintering-Deoxygenation Method

Science.gov (United States)

Sun, Pei; Fang, Z. Zak; Zhang, Ying; Xia, Yang

2017-12-01

Commercial spherical Ti powders for additive manufacturing applications are produced today by melt-atomization methods at relatively high costs. A meltless production method, called granulation-sintering-deoxygenation (GSD), was developed recently to produce spherical Ti alloy powder at a significantly reduced cost. In this new process, fine hydrogenated Ti particles are agglomerated to form spherical granules, which are then sintered to dense spherical particles. After sintering, the solid fully dense spherical Ti alloy particles are deoxygenated using novel low-temperature deoxygenation processes with either Mg or Ca. This technical communication presents results of 3D printing using GSD powder and the selective laser melting (SLM) technique. The results showed that tensile properties of parts fabricated from spherical GSD Ti-6Al-4V powder by SLM are comparable with typical mill-annealed Ti-6Al-4V. The characteristics of 3D printed Ti-6Al-4V from GSD powder are also compared with that of commercial materials.

The Formation Time of Ti-O• and Ti-O•-Ti Radicals at the n-SrTiO3/Aqueous Interface during Photocatalytic Water Oxidation.

Science.gov (United States)

Chen, Xihan; Choing, Stephanie N; Aschaffenburg, Daniel J; Pemmaraju, C D; Prendergast, David; Cuk, Tanja

2017-02-08

The initial step of photocatalytic water oxidation reaction at the metal oxide/aqueous interface involves intermediates formed by trapping photogenerated, valence band holes on different reactive sites of the oxide surface. In SrTiO 3, these one-electron intermediates are radicals located in Ti-O • (oxyl) and Ti-O • -Ti (bridge) groups arranged perpendicular and parallel to the surface respectively, and form electronic states in the band gap of SrTiO 3 . Using an ultrafast sub band gap probe of 400 nm and white light, we excited transitions between these radical states and the conduction band. By measuring the time evolution of surface reflectivity following the pump pulse of 266 nm light, we determined an initial radical formation time of 1.3 ± 0.2 ps, which is identical to the time to populate the surface with titanium oxyl (Ti-O • ) radicals. The oxyl was separately observed by a subsurface vibration near 800 cm -1 from Ti-O located in the plane right below Ti-O • . Second, a polarized transition optical dipole allows us to assign the 1.3 ps time constant to the production of both O-site radicals. After a 4.5 ps delay, another distinct surface species forms with a time constant of 36 ± 10 ps with a yet undetermined structure. As would be expected, the radicals' decay, specifically probed by the oxyl's subsurface vibration, parallels that of the photocurrent. Our results led us to propose a nonadiabatic kinetic mechanism for generating radicals of the type Ti-O • and Ti-O • -Ti from valence band holes based on their solvation at aqueous interfaces.

The Digital technical documentation handbook

CERN Document Server

Schultz, Susan I; Kavanagh, Frank X; Morse, Marjorie J

1993-01-01

The Digital Technical Documentation Handbook describes the process of developing and producing technical user information at Digital Equipment Corporation. * Discusses techniques for making user information _more effective * Covers the draft and reviewprocess, the production and distribution of printed and electronic media, archiving, indexing, testing for usability, and many other topics * Provides quality assurance checklists, contains a glossary and a bibliography of resources for technicalcommunicators

Unique strategies for technical information management at Johnson Space Center

Science.gov (United States)

Krishen, Vijay

1994-01-01

In addition to the current NASA manned programs, the maturation of Space Station and the introduction of the Space Exploration programs are anticipated to add substantially to the number and variety of data and documentation at NASA Johnson Space Center (JSC). This growth in the next decade has been estimated at five to ten fold compared to the current numbers. There will be an increased requirement for the tracking and currency of space program data and documents with National pressures to realize economic benefits from the research and technological developments of space programs. From a global perspective the demand for NASA's technical data and documentation is anticipated to increase at local, national, and international levels. The primary users will be government, industry, and academia. In our present national strategy, NASA's research and technology will assume a great role in the revitalization of the economy and gaining international competitiveness. Thus, greater demand will be placed on NASA's data and documentation resources. In this paper the strategies and procedures developed by DDMS, Inc., to accommodate the present and future information utilization needs are presented. The DDMS, Inc., strategies and procedures rely on understanding user requirements, library management issues, and technological applications for acquiring, searching, storing, and retrieving specific information accurately and quickly. The proposed approach responds to changing customer requirements and product deliveries. The unique features of the proposed strategy include: (1) To establish customer driven data and documentation management through an innovative and unique methods to identify needs and requirements. (2) To implement a structured process which responds to user needs, aimed at minimizing costs and maximizing services, resulting in increased productivity. (3) To provide a process of standardization of services and procedures. This standardization is the central

Overview of decommissioning and decontamination technical information support activities funded by the US Department of Energy's remedial action programs

International Nuclear Information System (INIS)

Owen, P.T.

1986-01-01

In 1979 the US Department of Energy (DOE) established the Remedial Action Program Information Center (RAPIC) at the Oak Ridge National Laboratory to provide technical information support to the Surplus Facilities Management Program, DOE's national decommissioning and decontamination (D and D) program which is managed by DOE's Richland Operations Office and UNC Nuclear Industries, Inc., and to the other DOE remedial action programs. Specific information activities that RAPIC performs to support the DOE's programs and the D and D community include: maintaining a computerized bibliographic database containing about 4500 annotated citations (about 2000 on D and D) and a database of 1800 contacts involved with remedial action work at radioactively contaminated sites; publishing an annual bibliography, ''Nuclear Facility Decommissioning and Site Remedial Actions, A Selected Bibliography,'' ORNL/EIS-154 (six volumes published); maintaining a document repository and providing copies of requested publications; and performing manual and computerized searches of the technical literature. The most significant RAPIC function is serving as a focal point for D and D information. With the extensive resources at its command, RAPIC is in a unique position to provide a comprehensive information base to the D and D community. DOE makes these services available to foster good public relations and promote cooperation and information exchange

Ti and N adatom descent pathways to the terrace from atop two-dimensional TiN/TiN(001) islands

Energy Technology Data Exchange (ETDEWEB)

Edström, D., E-mail: daned@ifm.liu.se [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Sangiovanni, D.G.; Hultman, L.; Chirita, V. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Petrov, I.; Greene, J.E. [Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-58183 Linköping (Sweden); Frederick Seitz Materials Research Laboratory and the Materials Science Department, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States)

2014-05-02

We use classical molecular dynamics and the modified embedded atom method to determine residence times and descent pathways of Ti and N adatoms on square, single-atom-high, TiN islands on TiN(001). Simulations are carried out at 1000 K, which is within the optimal range for TiN(001) epitaxial growth. Results show that the frequency of descent events, and overall adatom residence times, depend strongly on both the TiN(001) diffusion barrier for each species as well as the adatom island-edge location immediately prior to descent. Ti adatoms, with a low diffusion barrier, rapidly move toward the island periphery, via funneling, where they diffuse along upper island edges. The primary descent mechanism for Ti adatoms is via push-out/exchange with Ti island-edge atoms, a process in which the adatom replaces an island edge atom by moving down while pushing the edge atom out onto the terrace to occupy an epitaxial position along the island edge. Double push-out events are also observed for Ti adatoms descending at N corner positions. N adatoms, with a considerably higher diffusion barrier on TiN(001), require much longer times to reach island edges and, consequently, have significantly longer residence times. N adatoms are found to descend onto the terrace by direct hopping over island edges and corner atoms, as well as by concerted push-out/exchange with N atoms adjacent to Ti corners. For both adspecies, we also observe several complex adatom/island interactions, before and after descent onto the terrace, including two instances of Ti island-atom ascent onto the island surface. - Highlights: • We use classical molecular dynamics to model Ti and N adatom migration on TiN(001) islands. • N adatoms remain on islands significantly longer than Ti adatoms. • Ti adatoms descend via push-out/exchange, N adatoms primarily by direct hops. • N adatoms act as precursors for multilayer formation and surface roughening.

Ti and N adatom descent pathways to the terrace from atop two-dimensional TiN/TiN(001) islands

International Nuclear Information System (INIS)

Edström, D.; Sangiovanni, D.G.; Hultman, L.; Chirita, V.; Petrov, I.; Greene, J.E.

2014-01-01

We use classical molecular dynamics and the modified embedded atom method to determine residence times and descent pathways of Ti and N adatoms on square, single-atom-high, TiN islands on TiN(001). Simulations are carried out at 1000 K, which is within the optimal range for TiN(001) epitaxial growth. Results show that the frequency of descent events, and overall adatom residence times, depend strongly on both the TiN(001) diffusion barrier for each species as well as the adatom island-edge location immediately prior to descent. Ti adatoms, with a low diffusion barrier, rapidly move toward the island periphery, via funneling, where they diffuse along upper island edges. The primary descent mechanism for Ti adatoms is via push-out/exchange with Ti island-edge atoms, a process in which the adatom replaces an island edge atom by moving down while pushing the edge atom out onto the terrace to occupy an epitaxial position along the island edge. Double push-out events are also observed for Ti adatoms descending at N corner positions. N adatoms, with a considerably higher diffusion barrier on TiN(001), require much longer times to reach island edges and, consequently, have significantly longer residence times. N adatoms are found to descend onto the terrace by direct hopping over island edges and corner atoms, as well as by concerted push-out/exchange with N atoms adjacent to Ti corners. For both adspecies, we also observe several complex adatom/island interactions, before and after descent onto the terrace, including two instances of Ti island-atom ascent onto the island surface. - Highlights: • We use classical molecular dynamics to model Ti and N adatom migration on TiN(001) islands. • N adatoms remain on islands significantly longer than Ti adatoms. • Ti adatoms descend via push-out/exchange, N adatoms primarily by direct hops. • N adatoms act as precursors for multilayer formation and surface roughening

Deposit of thin films of TiN, a-C, Ti/TiN/a-C by laser ablation

International Nuclear Information System (INIS)

Mejia, I.S.; Escobar A, L.; Camps, E.; Romero, S.; Muhl, S.

2006-01-01

Thin films of titanium nitride (TiN), amorphous carbon (a-C), as well as bilayers of Ti/TiN/a-C were deposited by means of the laser ablation technique. It was investigated the effect that it has the laser fluence used to ablation the targets in the structure and mechanical properties of the TiN deposited films. The TiN obtained films have a preferential orientation in the direction (200). The results show that the hardness of this material is influenced by the laser fluence. It is observed that the hardness is increased in an approximately lineal way with the increment of the fluence up to 19 J/cm 2 . The films of amorphous carbon present hardness of the order of 11.2 GPa. Likewise it was found that the multilayers of Ti/TiN/aC presented a bigger hardness that of its individual components. (Author)

The effects of severe plastic deformation on some properties relevant to Ti implants

Directory of Open Access Journals (Sweden)

Anibal Andrade Mendes Filho

2012-02-01

Full Text Available In some types of surgical implants, such as bone screws and plates, Grade 2 Ti is seriously considered as a replacement for the Ti-6Al-4V alloy. Advantages are lower cost and the absence of Al and V, which have been identified as potentially harmful to human health. The present paper shows that the lower strength of the commercially pure metal can be enhanced by Severe Plastic Deformation followed by conventional cold rolling, so as to reach a strength level higher than the technical requirements applicable to the alloy. This was ascertained by tensile and Vickers hardness tests from which it was concluded that the best combination of properties are obtained by submitting the metal to Equal Channel Angular Pressing (four passes at 300 °C followed by a 70% thickness reduction by cold rolling. Although the present results are valid for the material only, and not for the product considered, that is, bone screws, it appears that this solution is a step towards the replacement of the Ti6-4 alloy by Grade 2 Ti, at least for some types of metallic medical implants.

The permeation behavior of deuterium through 1Cr18Ni9Ti stainless steel with TiN+TiC-TiN multiple films

International Nuclear Information System (INIS)

Xiong, Y.; Song, J.; Luo, D.; Lei, Q.; Chen, C.

2015-01-01

The prevention of tritium losses via permeation through structure components is an important issue in fusion technology. The production of thin layers on materials with low diffusivity and/or low surface recombination constants (so-called permeation barriers) seems to be the most practical method to reduce or hinder the permeation of tritium through materials. TiN+TiC+TiN multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel by ion-beam assisted deposition technology. The characteristics of films are tested by XPS ASEM and XRD, which shows that the film are compact and uniform with a thickness of about 15 μm, and have a good adherence with the substrate below 773 K. The diffraction peaks in the XRD patterns for TiC and TiN are broadened, implying that the multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel. Meanwhile, the C-H bonded CH 4 -appears in the infrared spectra of multiple films, suggesting that the CH 4 - is in a static state, so hydrogen atom cannot migrate from the site bonded with carbon to a neighboring site. The measured deuterium permeability in 1Cr18Ni9Ti stainless steel coated with multiple films is 2-3 orders of magnitude lower than that of pure 1Cr18Ni9Ti stainless steel substrate from 473 K to 773 K. However, this barrier is partly destroyed above 773 K

Technical Assistance Needs Assessments (TANAs)

Science.gov (United States)

The Technical Assistance Needs Assessment (TANA) is a process to identify whether a community requires additional support from EPA in order to understand technical information and have meaningful participation in the Superfund decision-making process.

Composition powders of the system TiC-TiB2

International Nuclear Information System (INIS)

Degrave, I.E.; Udalov, Yu.P.

2000-01-01

The ceramic composition on TiC-TiB 2 base is proposed for substitution of scarce and expensive tungsten carbide for manufacturing metallo-ceramic articles. The technology of TiC and TiB 2 powder production from the mixture of oxides and carbon-bearing reducing agents is developed. Saccharose is recommended to be used as a reductant. Carbon tetrachloride vapors are introduced into the reaction volume to accelerate the synthesis. The purification of the product from residual carbon is performed in high frequency glow discharge with the use of air as a plasma forming gas. Microstructural studies show that the product obtained constitutes submicron TiC particles in a TiB 2 matrix [ru

Deformation twinning in metals and ordered intermetallics-Ti and Ti-aluminides

Science.gov (United States)

Yoo, M. H.; Fu, C. L.; Lee, J. K.

1991-06-01

The role of deformation twinning in the strength and ductility of metals and ordered intermetallic alloys is examined on the basis of crystallography, energetics and kinetics of deformation twinning. A systematic analysis is made by taking Ti, Ti3AI, TiAl, and A13Ti as four model systems. In comparison with profuse twinning in Ti, the intrinsic difficulty of twinning in Ti3A1 is rationalized in terms of the interchange shuffling mechanism. A fault (SISF) dragging mechanism based on the interaction torque explains the physical source for the low mobility of screw superdislocations in TiAl, which may lead to (111) [ 11bar{2}] twin nucleation. In TiAl and A13Ti alloys, the twin-slip (ordinary) conjugate relationship makes an important contribution to the strain compatibility for high-temperature plasticity. Potentially beneficial alloying additions to promote twinning are discussed. Les conséquences de la déformation par maclage sur la fracture et la ductilité des métaux et alliages intermétalliques ordonnés sont étudiées en fonction de la cristallographie, de l'énergie et de la cinétique des déformations par maclage. Une analyse systématique a été faite en considérant Ti, Ti3AI, TiAl et A13Ti comme quatre systèmes modèles. En comparaison avec le nombre important de maclages observés dans Ti, la difficulté intrinsèque des maclages dans Ti3AI est rationalisée en terme de mécanisme d'“interchange shuffling”. Un mécanisme de “dragging fault” basé sur l'interaction “torque” explique l'origine physique de la faible mobilité des superdislocations vissées dans TiAl qui peuvent conduire à la nucléation des macles (111) 112. Dans les alliages tels TiAl et A13Ti, la relation conjuguée entre la macle et le glissement (ordinaire) contribue de façon importante à la compatibilité des contraintes lors de la déformation plastique à haute température. Des effets bénéfiques potentiels liés à des éléments d'addition sur le processus

Formation of Ti(III) and Ti(IV) states in Ti{sub 3}O{sub 5} nano- and microfibers obtained from hydrothermal annealing of C-doped TiO{sub 2} on Si

Energy Technology Data Exchange (ETDEWEB)

Stem, Nair, E-mail: nairstem@hotmail.com [Laboratório de Sistemas Integráveis (LSI), Escola Politécnica, Universidade de São Paulo, Av. Prof. Luciano Gualberto 158, 05508900 São Paulo, SP (Brazil); Souza, Michele L.; Araújo de Faria, Dalva Lúcia Araújo [Laboratório de Espectroscopia Molecular (LEM), Instituto de Química, Universidade de São Paulo, Av. Prof. Lineu Prestes 748, 05508900 São Paulo, SP (Brazil); Santos Filho, Sebastião G. dos [Laboratório de Sistemas Integráveis (LSI), Escola Politécnica, Universidade de São Paulo, Av. Prof. Luciano Gualberto 158, 05508900 São Paulo, SP (Brazil)

2014-05-02

In this work, it is investigated the formation of Ti(III) and Ti(IV) states at the surface and in the bulk of the Ti{sub 3}O{sub 5} material grown as meshes of nano- and micro-fibers obtained from hydrothermal annealing of C-doped TiO{sub 2} on Si. The topography and distribution of the fibers in the meshes were characterized by atomic force microscopy. When the fiber distribution was more compact, a higher photoluminescence signal at 850 nm (1.46 eV) was obtained, indicating the presence of a higher number of defects corresponding to the Ti(III) sites. From X-ray photoelectron spectroscopy, it was obtained a Ti(III)/Ti(IV) ratio much lower than the expected value for the Ti{sub 3}O{sub 5} phase (2 Ti(III): 1 Ti(IV)). The discrepancy was mainly attributed to the reaction of surface Ti(III) states of the Ti{sub 3}O{sub 5} fibers with water during the hydrothermal annealing, resulting in surface Ti(IV) with -OH radicals. On the other hand, X-ray photoelectron spectroscopy also indicated that substitutional and interstitial carbon atoms coexist, elemental carbon exists in the samples due to the co-deposition process and, as a result, the carbon inside of the TiO{sub 2} rutile lattice is acting as one of the precursors for the formation of Ti{sub 3}O{sub 5}. - Highlights: • Ti(III) states are detected inside of Ti{sub 3}O{sub 5} nano- and microfibers. • Ti(IV) states are predominantly detected on the surface of Ti{sub 3}O{sub 5} nano- and microfibers. • Photoluminescence at 850 nm for Ti{sub 3}O{sub 5} is due to defects associated to Ti(III). • Rutile possibly changes to C2/m Ti{sub 3}O{sub 5} during the hydrothermal annealing of C-doped TiO{sub 2}.

Characterization of laser deposited Ti6Al4V/TiC composite powders on a Ti6Al4V substrate

CSIR Research Space (South Africa)

Mahamood, RM

2014-01-01

Full Text Available This paper reports the material characterization of Ti6Al4V/TiC composite produced by laser metal deposition. The Ti6Al4V/TiC composites were deposited with a composition ratio of 50 wt.% Ti64l4V and 50 wt.% TiC. The depositions were achieved...

DOE technical standards list: Department of Energy standards index

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This Department of Energy (DOE) technical standards list (TSL) has been prepared by the Office of Nuclear Safety Policy and Standards (EH-31) on the basis of currently available technical information. Periodic updates of this TSL will be issued as additional information is received on standardization documents being issued, adopted, or canceled by DOE. This document was prepared for use by personnel involved in the selection and use of DOE technical standards and other Government and non-Government standards. This TSL provides listings of current DOE technical standards, non-Government standards that have been adopted by DOE, other standards-related documents in which DOE has a recorded interest, and canceled DOE technical standards. Information on new DOE technical standards projects, technical standards released for coordination, recently published DOE technical standards, and activities of non-Government standards bodies that may be of interest to DOE is published monthly in Standards Actions.

Layered Composite of TiC-TiB2 to Ti-6Al-4V in Graded Composition by Combustion Synthesis in High-gravity Field

International Nuclear Information System (INIS)

Huang Xuegang; Zhao Zhongmin; Zhang Long

2013-01-01

By taking combustion synthesis to prepare solidified TiB 2 matrix ceramic in high-gravity field, the layered composite of TiC-TiB 2 ceramic to Ti-6Al-4V substrate in graded composition was achieved. XRD, FESEM and EDS results showed that the bulk full-density solidified TiC-TiB 2 composite was composed of fine TiB 2 platelets, TiC irregular grains, a few of α-Al 2 O 3 inclusions and Cr alloy phases, and α'-Ti phases alternating with Ti-enriched carbides constituted the matrix of the joint in which fine TiB platelets were embedded, whereas some C, B atoms were also detected at the heat-affected zone of Ti-6A1-4V substrate. The layered composite of the solidified ceramic to Ti-6Al-4V substrate in graded composition with continuous microstructure was considered a result of fused joint and inter-diffusion between liquid ceramic and surface-molten Ti alloy, followed by TiB 2 -Ti peritectic reaction and subsequent eutectic reaction in TiC-TiB-Ti ternary system.

Introduction of Geographical Information Systems (GIS) in Technical University Education in Ghana: Challenges and the Way Forward

Science.gov (United States)

Acquah, Prince C.; Asamoah, Jack N.; Konadu, Daniel D.

2017-01-01

Geographic Information System (GIS) continue to play very important role in improving spatial thinking skills of graduates from higher educational institutions. However, teaching and learning of GIS at the technical university level in Ghana remains very limited due to some implementation challenges. This paper reviews the implementation of GIS in…

76 FR 7870 - Agency Information Collection Activities: Cybersecurity and Communications Technical Assistance...

Science.gov (United States)

2011-02-11

...: Technical Assistance Request and Evaluation. Form: DHS Form 9042, DHS Form 9043. OMB Number: 1670-NEW... technical assistance requests from each State and territory. The Technical Assistance Evaluation Form is... will be submitted electronically. Evaluation forms may be submitted electronically or in paper form...

Scientific and Technical Reports, Articles, Papers, and Presentations

Science.gov (United States)

Waits, J. E. Turner (Compiler)

2001-01-01

This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 2000. It also includes papers of MSFC contractors. After being announced in STAR, all the NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

Contribution to the study of U-Ti and U-Pu-Ti carbides; Contribution a l'etude des carbures U-C-Ti et (U, Pu) - C-Ti

Energy Technology Data Exchange (ETDEWEB)

Milet, C A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

After having discussed the reasons to use (U,Pu) carbides as fast reactor fuel, we examine the influence of the addition of titanium to these carbides. A preliminary study has been done on the system of U-C-Ti and some properties have been measured such as: density, thermal expansion, electrical resistivity, atmospheric corrosion and compatibility with stainless steel. The systems U-Pu-C-Ti (Pu/U + Pu equal to 15 per cent) and U-C-Ti have been found to be very similar. There exists a two phases region (U,Pu)C + TiC, an eutectic between (U,Pu)C and TiC for approximately 15 at %. The solubilities of U + Pu in TiC and of Ti in (U,Pu)C is less than 1 % at. The addition of titanium does not markedly change thermal expansion coefficients of (U,Pu)C. However the resistance to atmospheric corrosion and compatibility with stainless steel is improved. Thermal conductivity, calculated from electrical resistivity, has increased. On the other side, the density of fissile material is lowered. The combination of (U,Pu)C + TiC seems to be the most promising alloy for application as nuclear fuel. (author) [French] Apres avoir rappele les problemes poses par un combustible pour les reacteurs a neutrons rapides et l'interet des carbures U-Pu-C comme combustible, on examine l'influence de l'addition de titane dans ces carbures. Une etude preliminaire sur le systeme U-C-Ti a ete effectuee et quelques proprietes sont indiquees: densite, coefficients de dilatation, resistivite electrique, tenue a la corrosion atmospherique, compatibilite avec l'acier inoxydable. Le systeme U-Pu-C-Ti (Pu/U + Pu egal a 15 pour cent) presente de grandes analogies avec le systeme U-C-Ti. Il existe un domaine biphase (U,Pu)C + TiC, un eutectique entre (U,Pu)C et TiC pour environ 15 at % Ti; les solubilites de U + Pu clans TiC et de Ti dans (U,Pu)C sont inferieures a 1 at %. Par rapport a la phase (U,Pu)C, l'addition de titane est sans effets importants sur les coefficients de dilatation. Par contre la tenue a

The design, fabrication, and photocatalytic utility of nanostructured semiconductors: focus on TiO2-based nanostructures

Directory of Open Access Journals (Sweden)

Arghya Narayan Banerjee

2011-02-01

Full Text Available Arghya Narayan BanerjeeSchool of Mechanical Engineering, Yeungnam University, Gyeongsan, South KoreaAbstract: Recent advances in basic fabrication techniques of TiO2-based nanomaterials such as nanoparticles, nanowires, nanoplatelets, and both physical- and solution-based techniques have been adopted by various research groups around the world. Our research focus has been mainly on various deposition parameters used for fabricating nanostructured materials, including TiO2-organic/inorganic nanocomposite materials. Technically, TiO2 shows relatively high reactivity under ultraviolet light, the energy of which exceeds the band gap of TiO2. The development of photocatalysts exhibiting high reactivity under visible light allows the main part of the solar spectrum to be used. Visible light-activated TiO2 could be prepared by doping or sensitizing. As far as doping of TiO2 is concerned, in obtaining tailored material with improved properties, metal and nonmetal doping has been performed in the context of improved photoactivity. Nonmetal doping seems to be more promising than metal doping. TiO2 represents an effective photocatalyst for water and air purification and for self-cleaning surfaces. Additionally, it can be used as an antibacterial agent because of its strong oxidation activity and superhydrophilicity. Therefore, applications of TiO2 in terms of photocatalytic activities are discussed here. The basic mechanisms of the photoactivities of TiO2 and nanostructures are considered alongside band structure engineering and surface modification in nanostructured TiO2 in the context of doping. The article reviews the basic structural, optical, and electrical properties of TiO2, followed by detailed fabrication techniques of 0-, 1-, and quasi-2-dimensional TiO2 nanomaterials. Applications and future directions of nanostructured TiO2 are considered in the context of various photoinduced phenomena such as hydrogen production, electricity generation via

Characterization and Comparison of Photocatalytic Activity Silver Ion doped on TiO2(TiO2/Ag+) and Silver Ion doped on Black TiO2(Black TiO2/Ag+)

Science.gov (United States)

Kim, Jin Yi; Sim, Ho Hyung; Song, Sinae; Noh, Yeoung Ah; Lee, Hong Woon; Taik Kim, Hee

2018-03-01

Titanium dioxide (TiO2) is one of the representative ceramic materials containing photocatalyst, optic and antibacterial activity. The hydroxyl radical in TiO2 applies to the intensive oxidizing agent, hence TiO2 is suitable to use photocatalytic materials. Black TiO2was prepared through reduction of amorphous TiO2 conducting under H2 which leads to color changes. Its black color is proven that absorbs 100% light across the whole-visible light, drawing enhancement of photocatalytic property. In this study, we aimed to compare the photocatalytic activity of silver ion doped on TiO2(TiO2/Ag+) and silver ion doped on black TiO2(black TiO2/Ag+) under visible light range. TiO2/Ag+ was fabricated following steps. 1) TiO2 was synthesized by a sol-gel method from Titanium tetraisopropoxide (TTIP). 2) Then AgNO3 was added during an aging process step for silver ion doping on the surface of TiO2. Moreover, Black TiO2/Ag+ was obtained same as TiO2/Ag+ except for calcination under H2. The samples were characterized X-ray diffraction (XRD), UV-visible reflectance (UV-vis DRS), and Methylene Blue degradation test. XRD analysis confirmed morphology of TiO2. The band gap of black TiO2/Ag+ was confirmed (2.6 eV) through UV-vis DRS, which was lower than TiO2/Ag+ (2.9 eV). The photocatalytic effect was conducted by methylene blue degradation test. It demonstrated that black TiO2/Ag+ had a photocatalytic effect under UV light also visible light.

Strengthening mechanisms in Ti-6Al-4V/TiC composites

International Nuclear Information System (INIS)

Johnson, A.J. Wagoner; Kumar, K.S.; Briant, C.L.

2004-01-01

In this study, the compressive behavior of Ti-6Al-4V/TiC composites considered for ballistic applications was examined at strain rates of 0.1, 1.0, and 10 s-1. As little as 1 vol% of particulate TiC provided nearly a 25% increase in strength in Ti-6Al-4V/TiC composites over that of the monolithic Ti-6Al-4V, while subsequent additions of TiC did not provide proportional benefit. The mechanisms responsible for such a significant increase in strength were investigated for the first time in this study. Microscopy (optical, SEM, TEM) aided in identifying the possible strengthening mechanisms that are typically important to the strength of metal matrix composites. These mechanisms include grain size and subgrain size refinement and an increase in dislocation density, all of which can occur during processing. Two other important mechanisms are thermal mismatch strains and load transfer from the matrix to the particle; the contribution of these mechanisms to the strength of the composite was evaluated using the Eshelby approach. A quantitative comparison of the mechanisms listed clearly showed that none of them was responsible for the large increase in strength with only 1vol%TiC in Ti-6Al-4V. The results from this study show for the first time that carbon in solution is, by far, the most potent strengthening mechanism in the Ti-6Al-4V/TiC particulate composites

Technical Training for Managers.

Science.gov (United States)

Haverland, Edgar M.

The question has arisen as to what kind of information a manager without extensive technical training needs to learn to supervise effectively. For example, the Nike Hercules fire control platoon leader, usually an officer in his first active duty assignment, seldom has had extensive technical training. Yet he is responsibile for the…

Technical Manual. The ACT®

Science.gov (United States)

ACT, Inc., 2014

2014-01-01

This manual contains technical information about the ACT® college readiness assessment. The principal purpose of this manual is to document the technical characteristics of the ACT in light of its intended purposes. ACT regularly conducts research as part of the ongoing formative evaluation of its programs. The research is intended to ensure that…

DOE Advanced Scientific Computing Advisory Committee (ASCAC) Subcommittee Report on Scientific and Technical Information

Energy Technology Data Exchange (ETDEWEB)

Hey, Tony [eScience Institute, University of Washington; Agarwal, Deborah [Lawrence Berkeley National Laboratory; Borgman, Christine [University of California, Los Angeles; Cartaro, Concetta [SLAC National Accelerator Laboratory; Crivelli, Silvia [Lawrence Berkeley National Laboratory; Van Dam, Kerstin Kleese [Pacific Northwest National Laboratory; Luce, Richard [University of Oklahoma; Arjun, Shankar [CADES, Oak Ridge National Laboratory; Trefethen, Anne [University of Oxford; Wade, Alex [Microsoft Research, Microsoft Corporation; Williams, Dean [Lawrence Livermore National Laboratory

2015-09-04

The Advanced Scientific Computing Advisory Committee (ASCAC) was charged to form a standing subcommittee to review the Department of Energy’s Office of Scientific and Technical Information (OSTI) and to begin by assessing the quality and effectiveness of OSTI’s recent and current products and services and to comment on its mission and future directions in the rapidly changing environment for scientific publication and data. The Committee met with OSTI staff and reviewed available products, services and other materials. This report summaries their initial findings and recommendations.

XPS investigations of tribolayers formed on TiN and (Ti,Re)N coatings

Energy Technology Data Exchange (ETDEWEB)

Oktay, Serkan; Kahraman, Zafer; Urgen, Mustafa; Kazmanli, Kursat, E-mail: kursat@itu.edu.tr

2015-02-15

Graphical abstract: - Highlights: • The (Ti,Re)N coating (8 ± 1.9 at.% Re) consisted of TiN and ReNx (x > 1.33) phases. • TiO{sub 2} provided low friction coefficient to TiN coating at 150 °C. • Re addition to TiN drastically dropped the friction coefficients to 0.17–0.22. • Re{sub 2}O{sub 7} provided very low friction coefficient to (Ti,Re)N coating. • Re addition to TiN improved the wear behavior. - Abstract: TiN and (Ti,Re)N coatings were deposited on high-speed-steel substrates by a hybrid coating system composed of cathodic arc PVD and magnetron sputtering techniques. In order to keep rhenium content low (8 ± 1.9 at.%) in the coating, magnetron sputtering technique was utilized to evaporate rhenium. The (Ti,Re)N coating consisted of TiN and ReN{sub x} (x > 1.33) phases. The hardness of TiN and (Ti,Re)N were 31 GPa and 29 GPa ( ± 2 GPa), respectively. Tribological behaviors of the samples were tested against Al{sub 2}O{sub 3} balls at 21 °C (RT) and 150 °C (HT) by reciprocating wear technique. The tribolayers were analyzed by XPS technique. Friction coefficients of TiN were 0.56, 0.35 for 21 °C and 150 °C tests, respectively. Rhenium addition to TiN drastically dropped the friction coefficients to 0.22 and 0.17 for RT and HT samples. Rhenium addition also improved the wear resistance of the coating at both test temperatures. For TiN, main oxide component of the tribolayers was Ti{sub 2}O{sub 3} for RT tests and TiO{sub 2} for HT tests. The oxide layer formed on (Ti,Re)N were the mixture of TiO{sub 2}, Ti−O−N, ReO{sub 2} and Re{sub 2}O{sub 7} for both test temperatures. Re{sub 2}O{sub 7} provided very low friction coefficient to (Ti,Re)N. The findings are consistent with the crystal chemistry approach.

32 CFR 701.38 - Technical data.

Science.gov (United States)

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Technical data. 701.38 Section 701.38 National... DOCUMENTS AFFECTING THE PUBLIC FOIA Definitions and Terms § 701.38 Technical data. Recorded information, regardless of form or method of the recording, of a scientific or technical nature (including computer...

Biomineralisation with Saos-2 bone cells on TiSiN sputtered Ti alloys.

Science.gov (United States)

V V, Anusha Thampi; Bendavid, Avi; Martin, P J; Vaithilingam, Vijay; Bean, Penelope A; Evans, Margaret D M; Subramanian, B

2017-07-01

Surface modifications of metallic implants are important in order to protect the underlying metals from the harsh corrosive environment inside the human body and to minimize the losses caused by wear. Recently, researches are carried out in developing bioactive surfaces on metallic implants, which supports the growth and proliferation of cells on to these surfaces. Titanium silicon nitride (TiSiN) hard nanocomposites thin films were fabricated on Ti alloys (Ti-6Al-4V) by pulsed direct current (DC) reactive magnetron sputtering. The films were characterized for its microstructural and electrochemical behavior. The higher charge transfer resistance (Rct) and positive shift in Ecorr value of TiSiN/Ti alloys than the bare Ti-alloys indicates a better corrosion resistance offered by the TiSiN thin films to the underlying substrates. The biological response to TiSiN/Ti alloys and control bare Ti-alloys was measured in vitro using cell-based assays with two main outcomes. Firstly, neither the Ti alloy nor the TiSiN thin film was cytotoxic to cells. Secondly, the TiSiN thin film promoted differentiation of human bone cells above the bare control Ti alloy as measured by alkaline phosphatase and calcium production. TiSiN thin films provide better corrosion resistance and protect the underlying metal from the corrosive environment. The thin film surface is both biocompatible and bioactive as indicated from the cytotoxicity and biomineralization studies. Copyright © 2017 Elsevier B.V. All rights reserved.

[NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 1:] The value of Scientific and Technical Information (STI), its relationship to Research and Development (R&D), and its use by US aerospace engineers and scientists

Science.gov (United States)

Pinelli, Thomas E.; Glassman, Myron; Barclay, Rebecca O.; Oliu, Walter E.

1990-01-01

The relationship between scientific and technical information (STI), its use by aerospace engineers and scientists, and the aerospace R&D process is examined. Data are presented from studies of the role of STI in the performance and management of R&D activities and the behavior of engineers when using and seeking information. Consideration is given to the information sources used to solve technical problems, the production and use of technical communications, and the use of libraries, technical information centers, and on-line data bases.

Effect of TiH2 in the preparation of MMC Ti based with TiC reinforcement

International Nuclear Information System (INIS)

Peillon, N.; Fruhauf, J.B.; Gourdet, S.; Feraille, J.; Saunier, S.; Desrayaud, C.

2015-01-01

Highlights: • Using TiH 2 precursors promotes the MMC densification and microstructure homogeneity. • Clear description of the TiH 2 interest and limitations. • Coupling of TGA, TMA and EBSD analyses to investigate the sintering process of MMC. • Process parameters: granulometry, precursor composition, temperature and rate. - Abstract: Many studies were carried out on the elaboration Metal Matrix Composites (MMCs) and a wide variety of process is reported in the bibliography. For titanium based MMC, the basis material for these elaboration techniques mainly consists of atomized titanium powder. In this work a titanium hydride powder is used to elaborate Ti/TiC MMC. Although an additional dehydrogenation operation is required a significant decrease of the sintering temperature is expected with this basis powder. In this context, the behavior of titanium hydride powder mixed with 0, 10 and 20 vol.% TiC reinforcement is studied during densification by free sintering. The effects of particle size, temperature and rate of sintering reinforcement are discussed. The comparison of the TiH 2 process with Ti HDH (Hydride Dehydride) and atomized Ti mixture is made with 10 vol.% reinforcement. The results indicate that the sintering temperature is lowered and the final densities achieved are higher if the hydride is used. Interactions between dehydrogenation and sintering mechanisms clearly appear for the higher sintering temperature rate (10 °C/min) and need specific attention to prevent porosity nucleation through hydrogen entrapment

Synthesis, Characterization, and NIR Reflectance of Highly Dispersed NiTiO3 and NiTiO3/TiO2 Composite Pigments

Directory of Open Access Journals (Sweden)

Yuping Tong

2016-01-01

Full Text Available The highly dispersed nanostructured NiTiO3 pigments and NiTiO3/TiO2 composite pigments can be synthesized at relative low temperature. The activation energy of crystal growth of NiTiO3 during calcinations via salt-assistant combustion method is 9.35 kJ/mol. The UV-vis spectra results revealed that the absorbance decreased with the increasing of calcinations temperature due to small size effect of nanometer particles. The optical data of NiTiO3 nanocrystals were analyzed at the near-absorption edge. SEM showed that the obtained NiTiO3 nanocrystals and NiTiO3/TiO2 nanocomposite were composed of highly dispersed spherical-like and spherical particles with uniform size distribution, respectively. The chromatic properties and diffuse reflectance of samples were investigated. The obtained NiTiO3/TiO2 composite samples have higher NIR reflectance than NiTiO3 pigments.

Characterisation and behaviour of Ti/TiO2/noble metal anodes

International Nuclear Information System (INIS)

Gueneau de Mussy, Jean-Paul; Macpherson, Julie V.; Delplancke, Jean-Luc

2003-01-01

The morphology, composition and the electrical and electrochemical behaviour of the anodic microporous layer, prepared by the galvanostatic anodisation of Ti after sparking, followed by galvanostatic deposition of Pt or Ir have been investigated. These electrodes are proposed to function as dimensionally stable anodes (DSAs). For Ti/TiO 2 /Pt electrodes, Pt is deposited within some of the micropores of the oxide film. In contrast, for Ti/TiO 2 /Ir, the metal is deposited preferentially on the top surface. This difference is thought to result from the position of the metal deposition potential with respect to the flat band potential of n-TiO 2 . Optical imaging of both types of DSA suggests that only a few sites on the surface are responsible for electron exchange at the DSA-electrolyte interface. C-AFM measurements of Ti/TiO 2 /Pt samples subjected to long-term anodic polarisation, suggest that the Ti-noble metal contact is progressively insulated by thickening of the TiO 2 barrier layer, promoting passivation of the DSA. For Ir coated anodes, catalytic activity is directly related to the presence of Ir and to the stability of the catalytic oxide layer. Under Cu electrowinning conditions, the electrochemically formed hydrated Ir oxide was found to be catalytically less stable, than the iridium oxide film subjected to a heat treatment

Microstructure and refinement performance of Al-Ti-C master alloy: Effect of excess Ti on the growth and nucleating ability of TiC particles

Science.gov (United States)

Svynarenko, Kateryna; Zhang, Yubo; Jie, Jinchuan; Kutsova, Valentyna; Li, Tingju

2017-09-01

Al-5Ti-0.2C, Al-0.8Ti-0.2C, Al-8Ti-2C, and Al-10Ti master alloys were prepared and used to investigate the influence of excess Ti on the growth of TiC particles and its ability to nucleate Al-grains. The results of a microstructure analysis of TiC-containing alloys and refined CPAl were interrelated to the results of a refinement test. It was found that the presence of excess Ti is essential at the stage of master alloy preparation, as it facilitates the growth and uniform distribution of TiC within the structure. In Al-5Ti-0.2C alloy containing excess Ti, carbide particles grow faster and to a higher extent (from 0.29 μm to 0.44 μm) compared to Al-0.8Ti-0.2C alloy produced without excess Ti (from 0.29 μm to 0.32 μm). The results support the "Ti-transition zone theory" as the mechanism of grain refinement by TiC-containing master alloys. The refinement performance of Al-5Ti-0.2C is superior compared to the one achieved by adding Al-8Ti-2C and Al-10Ti master alloys in corresponding concentrations. For the TiC particles to become favourable nucleating sites, they must undergo certain interaction with excess Ti at the stage of master alloy preparation.

Single-Nanoparticle Photoelectrochemistry at a Nanoparticulate TiO2 -Filmed Ultramicroelectrode.

Science.gov (United States)

Peng, Yue-Yi; Ma, Hui; Ma, Wei; Long, Yi-Tao; Tian, He

2018-03-26

An ultrasensitive photoelectrochemical method for achieving real-time detection of single nanoparticle collision events is presented. Using a micrometer-thick nanoparticulate TiO 2 -filmed Au ultra-microelectrode (TiO 2 @Au UME), a sub-millisecond photocurrent transient was observed for an individual N719-tagged TiO 2 (N719@TiO 2 ) nanoparticle and is due to the instantaneous collision process. Owing to a trap-limited electron diffusion process as the rate-limiting step, a random three-dimensional diffusion model was developed to simulate electron transport dynamics in TiO 2 film. The combination of theoretical simulation and high-resolution photocurrent measurement allow electron-transfer information of a single N719@TiO 2 nanoparticle to be quantified at single-molecule accuracy and the electron diffusivity and the electron-collection efficiency of TiO 2 @Au UME to be estimated. This method provides a test for studies of photoinduced electron transfer at the single-nanoparticle level. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Controllable hydrothermal synthesis of rutile TiO{sub 2} hollow nanorod arrays on TiCl{sub 4} pretreated Ti foil for DSSC application

Energy Technology Data Exchange (ETDEWEB)

Xi, Min [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China); Zhang, Yulan; Long, Lizhen [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Xinjun, E-mail: lixj@ms.giec.ac.cn [Key Laboratory of Renewable Energy, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China)

2014-11-15

Rutile TiO{sub 2} nanorod arrays (TNRs) were achieved by hydrothermal process on TiCl{sub 4} pretreated Ti foil. Subsequently, TNRs were hydrothermally etched in HCl solution to form hollow TiO{sub 2} nanorod arrays (H-TNRs). The TiCl{sub 4} pretreatment plays key roles in enhancement of Ti foil corrosion resistance ability and crystal nucleation introduction for TNRs growth. TNRs with desired morphology can be obtained by controlling TiCl{sub 4} concentration and the amount of tetrabutyl titanate (TTB) accordingly. TNRs with the length of ∼1.5 μm and diameter of ∼200 nm, obtained on 0.15 M TiCl{sub 4} pretreated Ti foil with 0.6 mL TTB, exhibits relatively higher photocurrent. The increased pore volume of the H-TNRs has contributed to the increased surface area which is benefit for Dye-Sensitized Solar Cells (DSSC) application. And the 180 °C-H-TNRs photoanode obtained from the 0.15-TiCl{sub 4}-TNRs sample demonstrated 128.9% enhancement of photoelectric efficiency of DSSC compared to that of the original TNR photoanode. - Graphical abstract: Rutile hollow TiO{sub 2} nanorod array photoanode obtained from original TiO{sub 2} nanorod array photoanode by hydrothermal etching demonstrates enhanced photoelectric efficiency of DSSC. - Highlights: • TiO{sub 2} nanorods are prepared via hydrothermal process on TiCl{sub 4}-pretreated Ti foil. • Hollow TiO{sub 2} nanorods are obtained by hydrothermal etching of TiO{sub 2} nanorods. • TiCl{sub 4} pretreatment plays a key role in protecting Ti foil from chemical corrosion. • Hollow TiO{sub 2} nanorods photoanode shows enhanced photoelectric efficiency for DSSC.

Laser processing of in situ TiN/Ti composite coating on titanium.

Science.gov (United States)

Sahasrabudhe, Himanshu; Soderlind, Julie; Bandyopadhyay, Amit

2016-01-01

Laser remelting of commercially pure titanium (CP-Ti) surface was done in a nitrogen rich inert atmosphere to form in situ TiN/Ti composite coating. Laser surface remelting was performed at two different laser powers of 425 W and 475 W. At each power, samples were fabricated with one or two laser scans. The resultant material was a nitride rich in situ coating that was created on the surface. The cross sections revealed a graded microstructure. There was presence of nitride rich dendrites dispersed in α-Ti matrix at the uppermost region. The structure gradually changed with lesser dendrites and more heat affected α-Ti phase maintaining a smooth interface. With increasing laser power, the dendrites appeared to be larger in size. Samples with two laser scans showed discontinuous dendrites and more α-Ti phase as compared to the samples with one laser scan. The resultant composite of TiN along with Ti2N in α-Ti showed substantially higher hardness and wear resistance than the untreated CP-Ti substrate. Coefficient of friction was also found to reduce due to surface nitridation. Leaching of Ti(4+) ions during wear test in DI water medium was found to reduce due to laser surface nitriding. Copyright © 2015 Elsevier Ltd. All rights reserved.

XPS study on the electronic structure of hydrided Ti-V, Ti-Nb and Ti-Mo alloys

International Nuclear Information System (INIS)

Tanaka, Kazuhide; Aoki, Hiromasa

1989-01-01

Effects of hydrogenation on the core and valence electronic structures of β(bcc)-stabilized Ti-25at%V, Ti-50at%Nb and Ti-20at%Mo alloys are studied with XPS technique using monochromatized Al K α radiation. Small but uniform binding-energy shifts are observed upon hydrogenation for all the core spectra measured. Their valence-band spectra are significantly distorted, providing an evidence of the formation of metal-hydrogen bonding bands in these Ti alloys. Interrelations between the core binding-energy shifts and the valence-band distortion are discussed. (orig.)

Determination of kinetic parameters in the systems Li0.5La0.5TiO3 and Li0.5La0.5TiO3/PANI by GITT (Galvanostatic intermittent titration technique)

International Nuclear Information System (INIS)

Pérez Cappe, Eduardo; Mosqueda Laffita, Yodalgis; Milian Pila, Carlos R.

2008-01-01

Full text: Oxides belonging to the family Li 3x La 2/3-x TiO 3 have been reported as materials of a high Ionic conductivity and a poor electronic conductivity at room temperature. The combination of these materials with other polymer in nature, such as polyaniline (PANI), of proven electronic properties, allows to obtain potentially applicable material in rechargeable Li. In this context the study of diffusive phenomena are of vital importance. A technical electrochemistry of intermittent rating (GITT), which combines state transient measurements and stationary, for the calculation of kinetic parameters in the Li 0.5 La 0.5 TiO 3 system and a composite comprising this oxide and PANI (Li 0.5 La 0.5 TiO 3 /PANI) in its conductive phase (emeraldine) is used in this work. Interesting considerations concerning shows the calculation of the numbers of ionic and electronic transport, necessary for the determination of coefficients of electronic dissemination. (author)

Characterization and fabrication of Ti/Pd bilayers for transition-edge sensors

International Nuclear Information System (INIS)

Monticone, E; Taralli, E; Portesi, C; Fretto, M; Rocci, R; Cerri, R; Rajteri, M

2009-01-01

Transition-edge sensor (TES) microcalorimeters are extensively used as single photon detectors from infrared to x-ray. Their good energy resolution and photon number resolving capability at visible and near-infrared wavelengths make them powerful tools for quantum information and quantum computation. In this work we report details on the fabrication of Ti/Pd TESs deposited by e-beam evaporation on silicon nitride substrates. By the proximity effect between Ti and Pd, the Ti critical temperature was tuned down to 100 mK, usual working temperature for these devices. Sharp transition of two-three mK and reproducible Tc were obtained. The Pd material can be a valid alternative to widely used Au proximity material thanks to its stronger influence on the Ti layer, that allows to obtain the same temperature reduction with thinner layers. Thermal and electrical characteristics of Ti/Au and Ti/Pd bilayers are compared in view of single photon detection.

AlTiN layer effect on mechanical properties of Ti-doped diamond-like carbon composite coatings

International Nuclear Information System (INIS)

Pang Xiaolu; Yang Huisheng; Gao Kewei; Wang Yanbin; Volinsky, Alex A.

2011-01-01

Ti/Ti-doped diamond-like carbon (DLC) and Ti/AlTiN/Ti-DLC composite coatings were deposited by magnetron sputtering on W18Cr4V high speed steel substrates. The effect of the AlTiN support layer on the properties of these composite coatings was investigated through microstructure and mechanical properties characterization, including hardness, elastic modulus, coefficient of friction and wear properties measured by scanning electron microscopy, Raman spectroscopy, scratch and ball-on-disk friction tests. Ti and AlTiN interlayers have a columnar structure with 50-80 nm grains. The hardness and elastic modulus of Ti/Ti-DLC and Ti/AlTiN/Ti-DLC coatings is 25.9 ± 0.4, 222.2 ± 6.3 GPa and 19.3 ± 1, 205.6 ± 6.7 GPa, respectively. Adhesion of Ti-DLC, Ti/AlTiN/Ti-DLC and AlTiN/Ti-DLC coatings expressed as the critical lateral force is 26.5 N, 38.2 N, and 47.8 N, respectively. Substrate coefficient of friction without coatings is 0.44, and it is 0.1 for Ti/Ti-DLC and Ti/AlTiN/Ti-DLC coatings. Wear resistance of Ti/AlTiN/Ti-DLC composite coatings is much higher than Ti/Ti-DLC coatings based on the wear track width of 169.8 and 73.2 μm, respectively, for the same experimental conditions.

Structural comparison of sintering products made of "TiC + Ti" composite powders and "Ti + C" powder mixtures

Science.gov (United States)

Krinitcyn, Maksim G.; Pribytkov, Gennadii A.; Korosteleva, Elena N.; Firsina, Irina A.; Baranovskii, Anton V.

2017-12-01

In this study, powder composite materials comprised of TiC and Ti with different ratios are processed by sintering of Ti and C powder mixtures and self-propagating high-temperature synthesis (SHS) in "Ti+C" system followed by sintering. The microstructure and porosity of obtained composites are investigated and discussed. The dependence of porosity on sintering time is explained theoretically. Optimal regimes that enable to obtain the most homogeneous structure with the least porosity are described.

A new traveltime approximation for TI media

KAUST Repository

Stovas, Alexey; Alkhalifah, Tariq Ali

2012-01-01

In a transversely isotropic (TI) medium, the trade-off between inhomogeneity and anisotropy can dramatically reduce our capability to estimate anisotropy parameters. By expanding the TI eikonal equation in power series in terms of the aneliptic parameter η, we derive an efficient tool to estimate (scan) for η in a generally inhomogeneous, elliptically anisotropic background medium. For a homogeneous-tilted transversely isotropic medium, we obtain an analytic nonhyperbolic moveout equation that is accurate for large offsets. In the common case where we do not have well information and it is necessary to resolve the vertical velocity, the background medium can be assumed isotropic, and the traveltime equations becomes simpler. In all cases, the accuracy of this new TI traveltime equation exceeds previously published formulations and demonstrates how η is better resolved at small offsets when the tilt is large.

A new traveltime approximation for TI media

KAUST Repository

Stovas, Alexey

2012-07-01

In a transversely isotropic (TI) medium, the trade-off between inhomogeneity and anisotropy can dramatically reduce our capability to estimate anisotropy parameters. By expanding the TI eikonal equation in power series in terms of the aneliptic parameter η, we derive an efficient tool to estimate (scan) for η in a generally inhomogeneous, elliptically anisotropic background medium. For a homogeneous-tilted transversely isotropic medium, we obtain an analytic nonhyperbolic moveout equation that is accurate for large offsets. In the common case where we do not have well information and it is necessary to resolve the vertical velocity, the background medium can be assumed isotropic, and the traveltime equations becomes simpler. In all cases, the accuracy of this new TI traveltime equation exceeds previously published formulations and demonstrates how η is better resolved at small offsets when the tilt is large.

Influence of information technologies on technical fitness of students in sport-oriented physical education

Directory of Open Access Journals (Sweden)

Zh.L. Kozina

2016-02-01

Full Text Available Purpose: to determine influence of information technologies in sport-oriented physical education on technical fitness of students, practicing football indoors. Material: in the researches students (boys - n=40 of 18-20 years’ age participated. Standard tests on physical condition were used. For determination of motor skills and abilities we used: juggling with ball; kick in pre-set sector of goal; shuttle run 4 x 10 meters with dribbling; kick for distance. Results: structural model of sport-oriented students’ physical education with application of information technologies has been formed. In the model all students are trained in sport-oriented academic groups by chosen kinds of sports (motor functioning. Such approach envisages holistic form of program material construction and unified algorithm of students’ progress assessment. Conclusions: the wholeness of sport-oriented physical education’s functioning is ensured at the account of application of information technologies. It permits to optimize motor skills’ training process. In this case single form of building of program material is created.

EDI and the Technical Communicator.

Science.gov (United States)

Eiler, Mary Ann

1994-01-01

Assesses the role of technical communicators in electronic data interchange (EDI). Argues that, as experts in information design, human factors, instructional theory, and professional writing, technical communicators should be advocates of standard documentation protocols and should rethink the traditional concepts of "document" to…

Microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steel

International Nuclear Information System (INIS)

Park, Ji Yoon; Kim, Kwan Hyu; Choe, Han Cheol

1999-01-01

The microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steels have been studied. AISI 304 stainless steels containing 0.1∼1.0 wt% Ti were fabricated by using vacuum furnace and followed by solutionization treatment at 1050 .deg. C for 1hr. The specimens were coated by Ti and TiN with 1 μm and 2 μm thickness by electron-beam PVD method. The microstructure and phase analysis were carried out by using XRD, WDS and SEM. Mechanical properties such as hardness (micro-Vickers) and wear resistance were examined. Coated films showed fine columnar structure and some defects. Surface roughness increased in all specimens after TiN coating. XRD patterns showed that the TiN(111) peak was major in TiN single-layer and the other peaks were very weak, but TiN(220) and TiN(200) peaks were developed in Ti/TiN double-layer. The hardness of the coating film was higher in Ti/TiN double-layer than in TiN single-layer and not affected by the Ti content of substrate. Ti/TiN double-layer showed better wear resistance than TiN single-layer. The observed wear traces were sheared type in all coated specimens

48 CFR 435.010 - Scientific and technical reports.

Science.gov (United States)

2010-10-01

... CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 435.010 Scientific and technical reports... all scientific and technical reports to the National Technical Information Service at the address... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Scientific and technical...

Tuning TiO2 nanoparticle morphology in graphene-TiO2 hybrids by graphene surface modification

Science.gov (United States)

Sordello, Fabrizio; Zeb, Gul; Hu, Kaiwen; Calza, Paola; Minero, Claudio; Szkopek, Thomas; Cerruti, Marta

2014-05-01

truncated bipyramids, bonded to graphene via the {100} facets. Belted truncated bipyramids formed on unfunctionalized GNP too, however the NPs were more irregular and rounded. These effects were ascribed to pH variations in the proximity of the functionalized GNP sheets, due to the high density of COOH or NH2 groups. Because of the different reactivity of anatase {100} and {101} crystalline facets, we hypothesize that the hybrid materials will behave differently as photocatalysts, and that the COOH-GNP-TiO2 hybrids will be better photocatalysts for water splitting and H2 production. Electronic supplementary information (ESI) available: Statistical analysis of the D : G intensity ratio, additional XPS analysis and TEM micrographs. See DOI: 10.1039/c4nr01322k

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

Technical training: WBTechT offers online training

CERN Multimedia

Davide Vitè

2006-01-01

The 2006 CERN Web-Based Technical Training (WBTechT) portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications (e.g. Microsoft Office Suite, Frontpage, Dreamweaver, Illustrator, Photoshop) and 90.- CHF for technical applications (e.g. Unix, Oracle, Java, JavaScript, C, C++) for three months'unlimited access. Visit the WBTechT portal, or the WBTechT information page at http://www.cern.ch/TechnicalTraining Contact: Technical.Training@cern.ch or your DTO to find out more information.

Technical innovation and policy of scientific technique

International Nuclear Information System (INIS)

Song, Wi Jin

2006-04-01

This book deals with system of innovation and policy of scientific technology : main view point and Topic, technical politics and technical learning, spread of internet and change of structure in information and communications industry, characteristic of technical innovation of software as open source, transfer into national innovation system, change of activity of public scientific technology, theory on technical innovation, evolution of technical innovation policy and participation of civil.

FY 2004 Scientific and Technical Reports, Articles, Papers, and Presentations

Science.gov (United States)

Fowler, B. A. (Compiler)

2006-01-01

This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center (MSFC) personnel FY 2004. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this TM maybe of value to the scientific and engineering community in determining what information has been published and what is available.

FY 2001 Scientific and Technical Reports, Articles, Papers, and Presentations

Science.gov (United States)

Waits, J. E. Turner (Compiler)

2002-01-01

This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 2001. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

Electrochemical properties of Ti3+ doped Ag-Ti nanotube arrays coated with hydroxyapatite

Science.gov (United States)

Zhang, Hangzhou; Shi, Xiaoguo; Tian, Ang; Wang, Li; Liu, Chuangwei

2018-04-01

Ag-Ti nanotube array was prepared by simple anodic oxidation method and uniform hydroxyapatite were electrochemically deposited on the nanotubes, and then characterized by SEM, XRD, XPS and EIS. In order to investigate the influence of Ti3+ on the electrochemical deposition of hydroxyapatite on the nanotubes, the Ag-Ti nanotube array self-doped with Ti3+ was prepared by one step reduction method. The experiment results revealed that the Ti3+ can promote the grow rate of hydroxyapatite coatings on nanotube surface. The hydroxyapatite coated Ag-Ti nanotube arrays with Ti3+ exhibit excellent stability and higher corrosion resistance. Moreover, the compact and dense hydroxyapatite coating can also prevent the Ag atom erosion from the Ag-Ti nanotube.

TRManager – Technical Risk Manager

Directory of Open Access Journals (Sweden)

Mark A. Gregory

2009-06-01

Full Text Available This paper presents research into the development of a new information management technique called Technical Risk Manager. Project management involves the use of processes and information management techniques to aid decision making in the pursuit of project success. Project success may be achieved by meeting time, cost or performance criteria. Current project management practices focus on achieving time and cost project success criteria by using three information management techniques developed in the 1950s: Gantt, PERT and Critical Path Method. Technical Risk Manager has been developed to provide an information management technique that may be used to aid project management decision making in the pursuit of achieving the performance project success criteria.

Characteristics and in vitro biological assessment of (Ti, O, N)/Ti composite coating formed on NiTi shape memory alloy

International Nuclear Information System (INIS)

Sun Tao; Wang Langping; Wang Min; Tong, Ho-Wang; Lu, William W.

2011-01-01

In this investigation, plasma immersion ion implantation and deposition (PIIID) was used to fabricate a (Ti, O, N)/Ti coating on NiTi shape memory alloy (SMA) to improve its long-term biocompatibility and wear resistance. The surface morphology, composition and roughness of uncoated and coated NiTi SMA samples were examined. Energy dispersive X-ray elemental mapping of cross-sections of (Ti, O, N)/Ti coated NiTi SMA revealed that Ni was depleted from the surface of coated samples. No Ni was detected by X-ray photoelectron spectroscopy on the surface of coated samples. Furthermore, three-point bending tests showed that the composite coating could undergo large deformation without cracking or delamination. After 1 day cell culture, SaOS-2 cells on coated samples spread better than those on uncoated NiTi SMA samples. The proliferation of SaOS-2 cells on coated samples was significantly higher at day 3 and day 7 of cell culture.

Optical and structural properties of TiO2/Ti/Ag/TiO2 and TiO2/ITO/Ag/ITO/TiO2 metal-dielectric multilayers by RF magnetron sputtering for display application

International Nuclear Information System (INIS)

Lee, Jang-Hoon; Lee, Seung-Hyu; Hwangbo, Chang-Kwon; Lee, Kwang-Su

2004-01-01

Electromagnetic-interference (EMI) shielding and near-infrared (NIR) cutoff filters for plasma display panels, based on fundamental structures (ITO/Ag/ITO), (TiO 2 /Ti/Ag/TiO 2 ) and (TiO 2 /ITO/Ag/ITO/TiO 2 ), were designed and prepared by RF-magnetron sputtering. The optical, structural and electrical properties of the filters were investigated by using spectrophotometry, Auger electron spectroscopy, X-ray photoelectron spectroscopy, Rutherford backscattering spectroscopy, atomic force microscopy and four-point-probe measurements. The results show that ITO films as the barriers and base layers lead to higher transmittance in the visible spectrum and smoother surface roughness than Ti metal barriers, while maintaining high NIR cutoff characteristics and chemical stability, which may be attributed to the lower absorption in the interfacial layers and better protection of the Ag layers by the ITO layers.

Analysis on the development of scientific and technical information under new competitive environment

International Nuclear Information System (INIS)

Li Tao

2010-01-01

The current external environment of information work has undergone profound changes. The world competition in Military fields, the development of national economy and the applications of high-technologies put forward higher requirements to intelligence work. Under the environment of global information integration, 'eyes and ears' roles of nuclear scientific and technical information will be more highlighted. In this context, we believe that the way of nuclear sci-tech information development should be focused on comprehensive research and be based on the building of information resources and advanced information technology methods, forming an integrated service system with capabilities of rapid resources, decision support, information assurance and sustainable development. The goal of nuclear sci-tech information development should be to serve the development of nuclear power and the popularization and application of nuclear technology in the fields of national economy, to implement the strategy of 'integrated intelligence support', to ensure the formation of rapid response capability, to enhance capabilities of decision support and science and technology development guidance, to build digital information resources and to constantly promote the research on network collaboration. This paper analyzes the characteristics of nuclear sci-tech information under new competitive environment, describes the ideas and goals of its development and proposes the way to achieve these goals. In order to provide the information support and service with the characteristics of rapid response, high quality and high efficiency, the paper also puts forward that under the new environment, we should optimize the service system, extend service functions, transform service mode, speed up the transformation on intelligence work, adjust and optimize business content and structure, promote business process re-engineering, and pay equal attention to 'ensuring demands' and 'guiding the future

Study and characterization of the irreversible transformation of electrically stressed planar Ti/TiO{sub x}/Ti junctions

Energy Technology Data Exchange (ETDEWEB)

Guillaume, N.; Puyoo, E., E-mail: etienne.puyoo@insa-lyon.fr; Le Berre, M.; Albertini, D.; Baboux, N.; Chevalier, C.; Ayadi, K.; Grégoire, J.; Gautier, B.; Calmon, F. [Institut des Nanotechnologies de Lyon, Université de Lyon, INL UMR 5270, CNRS, INSA de Lyon, Villeurbanne F-69621 (France)

2015-10-14

We investigate the properties and characteristics of planar Ti/TiO{sub x}/Ti junctions, which consist of transverse TiO{sub x} lines drawn on Ti test patterns. Junctions are elaborated by means of local anodic oxidation using atomic force microscopy. An irreversible morphological transformation occurring in a reproducible manner is observed when these planar junctions are electrically stressed under ambient atmosphere. Structural and chemical analyses based on transmission electron microscopy techniques reveal the extension of the initial amorphous TiO{sub x} into a crystalline rutile phase. This irreversible transformation is proven to vanish completely if the electrical stress occurs under vacuum atmosphere. Finally, we carry out temperature dependent electrical measurements in order to elucidate their conduction mechanism: Schottky emission above an ultra-low potential barrier is assumed to dominate under vacuum atmosphere whereas ionic conduction seems to prevail in air.

Fabrication of steel matrix composites locally reinforced with different ratios of TiC/TiB2 particulates using SHS reactions of Ni-Ti-B4C and Ni-Ti-B4C-C systems during casting

International Nuclear Information System (INIS)

Yang Yafeng; Wang Huiyuan; Liang Yunhong; Zhao Ruyi; Jiang Qichuan

2007-01-01

Steel matrix composites locally reinforced with different molar ratios of in situ TiC/TiB 2 particulates (2:1, 1:1 and 1:2, respectively) have been fabricated successfully utilizing the self-propagating high-temperature synthesis (SHS) reactions of Ni-Ti-B 4 C and Ni-Ti-B 4 C-C systems during casting. Differential thermal analysis (DTA) and X-ray diffraction (XRD) results reveal that the exothermic reactions of the Ni-Ti-B 4 C and Ni-Ti-B 4 C-C systems proceed in such a way that Ni initially reacts with B 4 C and Ti to form Ni 2 B and Ti 2 Ni compounds, respectively, with heat evolution at 1037 deg. C; Subsequently, the external heat and the evolved heat from these exothermic reactions promote the reactions forming TiC and TiB 2 at 1133 deg. C. In the composites reinforced with 1:2 molar ratio of TiC/TiB 2 , almost all TiB 2 grains have clubbed structures, while TiC grains exhibit near-spherical morphologies. Furthermore, TiB 2 grain sizes decrease, with the increase of TiC content. In particular, in the composites reinforced with 2:1 molar ratio of TiC/TiB 2 , it is difficult to find the clubbed TiB 2 grains. Macro-pores and blowholes are absent in the local reinforcing region of the composites reinforced with 1:1 and 1:2 molar ratios of TiC/TiB 2 , while a few macro-pores can be observed in the composite reinforced with 2:1 molar ratio of TiC/TiB 2 . Moreover, the densities of the composites reinforced with 1:1 and 1:2 molar ratios of TiC/TiB 2 are higher than that of the composite reinforced with 2:1 molar ratio of TiC/TiB 2 . The composite reinforced with 1:2 molar ratio of TiC/TiB 2 has the highest hardness and the best wear resistance

Professional Technical Standards in Colleges and Schools of Pharmacy

Science.gov (United States)

Berry, Tricia M.; Chichester, Clinton O.; Sanoski, Cynthia A.; Woodward, Donald A.; Worley, Marcia M.; Early, Johnnie L.

2011-01-01

Objective To determine the prevalence, characteristics, and use of professional technical standards among colleges and schools of pharmacy accredited by the Accreditation Council for Pharmacy Education (ACPE). Methods The Web site of every college and school of pharmacy accredited by ACPE was searched to identify information regarding the availability, content, and use of technical standards and to obtain demographic information. Results Information was obtained from all of the 114 colleges and schools of pharmacy and 67 (59%) had technical standards in place. Common themes for technical standards were: observation; communication; motor; intellectual, conceptual, integrative and quantitative abilities; and behavioral and social attributes. Of those colleges and schools with technical standards, 61 (91%) had standards that addressed all 5 of these themes and 34 (51%) specified that the technical standards were used in their admission, progression, and graduation procedures. Conclusion More than half of the colleges and schools of pharmacy examined in this study have technical standards; however, 41% have yet to develop and implement them. Colleges and schools of pharmacy looking for guidance in technical standards development could use the technical standards themes identified in this study. PMID:21655404

Formation Mechanism of Spherical TiC in Ni-Ti-C System during Combustion Synthesis.

Science.gov (United States)

Zhu, Guoliang; Wang, Wei; Wang, Rui; Zhao, Chuanbao; Pan, Weitao; Huang, Haijun; Du, Dafan; Wang, Donghong; Shu, Da; Dong, Anping; Sun, Baode; Jiang, Sheng; Pu, Yilong

2017-08-29

The formation mechanism of TiC particles in a Ni-Ti-C system were revealed by using differential thermal analysis (DTA), XRD, and SEM to identify the reaction products in different temperature ranges. The results indicated that the synthesis mechanism of TiC in Ni-Ti-C system was complex; several reactions were involved in the combustion synthesis of TiC-Ni composite. The Ni-Ti intermediate phases play important roles during the formation of TiC. Moreover, the influence of heating rate on the size range of TiC was also discussed.

Formation of hydroxyapatite on Ti-coated Ti-Zr-Cu-Pd bulk metallic glass

International Nuclear Information System (INIS)

Qin, F.X.; Wang, X.M.; Wada, T.; Xie, G.Q.; Asami, K.; Inoue, A.

2009-01-01

In this research, Ti coating was conducted on Ti 40 Zr 10 Cu 36 Pd 14 bulk metallic glass (BMG) in order to increase the formation rate of hydroxyapatite layer. The formation behavior of bone-like hydroxyapatite on Ti-coated and uncoated Ti 40 Zr 10 Cu 36 Pd 14 bulk metallic glasses (BMGs) was studied. The surface morphology of Ti-coated and uncoated Ti 40 Zr 10 Cu 36 Pd 14 BMG was investigated by scanning electron microscopy and energy dispersive X-ray spectroscopy. The results revealed that the alkali pretreatment in 5 M NaOH solution at 60degC for 24 h had a beneficial effect on the formation of porous sodium titanate on Ti-coated Ti 40 Zr 10 Cu 36 Pd 14 BMG. A bone-like hydroxyapatite layer was able to form on the alkali-treated Ti-coated Ti 40 Zr 10 Cu 36 Pd 14 BMG after a short-time immersion in simulated body fluid (SBF). On the contrary, hydroxyapatite formation was not observed on the uncoated Ti 40 Zr 10 Cu 36 Pd 14 BMG after the same chemical treatments. (author)

Information support of monitoring of technical condition of buildings in construction risk area

Science.gov (United States)

Skachkova, M. E.; Lepihina, O. Y.; Ignatova, V. V.

2018-05-01

The paper presents the results of the research devoted to the development of a model of information support of monitoring buildings technical condition; these buildings are located in the construction risk area. As a result of the visual and instrumental survey, as well as the analysis of existing approaches and techniques, attributive and cartographic databases have been created. These databases allow monitoring defects and damages of buildings located in a 30-meter risk area from the object under construction. The classification of structures and defects of these buildings under survey is presented. The functional capabilities of the developed model and the field of it practical applications are determined.

Obtention of the TiFe compound by high-energy milling of Ti+Fe and TiH{sub 2}+Fe powder mixtures; Obtencao do composto TiFe a partir da moagem de alta energia de misturas Ti+Fe e TiH{sub 2}+Fe

Energy Technology Data Exchange (ETDEWEB)

Falcao, R.B.; Dammann, E.D.C.C.; Rocha, C.J.; Leal Neto, R.M., E-mail: railson.falcao@usp.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencias e Tecnologia de Materiais. Lab. de Intermetalicos

2010-07-01

In this work TiFe compound was obtained by two process routes involving high-energy ball milling: mechanical alloying from Ti and Fe powders (route 1) and mechanical milling from TiH{sub 2} and Fe powders, both followed by an annealing heat treatment. Shaker and planetary ball mills were utilized for times varying from 1-25 hours. Milled and annealed powders were characterized by SEM and X-ray diffraction analyses. TiFe compound was formed in both routes. A strong powder adherence in the milling vial and balls occurred with route 1 in both mills. Powder adherence was significantly reduced by using TiH{sub 2} (route 2) mainly in the planetary mill, in spite of TiFe formation has only occurred after the annealing treatment. (author)

Ultrasound assisted combustion synthesis of TiC in Al-Ti-C system.

Science.gov (United States)

Liu, Zhiwei; Rakita, Milan; Xu, Wilson; Wang, Xiaoming; Han, Qingyou

2015-11-01

This research investigated the effects of high-intensity ultrasound on the combustion synthesis of TiC particles in Al-Ti-C system. The process involved that high-intensity ultrasound was applied on the surface of a compacted Al-Ti-C pellet directly through a Nb probe during the thermal explosion reaction. By comparing with the sample without ultrasonic treatment, it was found that the thermal explosion reaction for synthesizing TiC phase could take place thoroughly in the ultrasonically treated sample. During the process of synthesizing TiC phase, the dissolution of solid graphite particles into the Al-Ti melt, as well as the nucleation and growth of TiC particles could be promoted effectively due to the effects of ultrasound, leading to an enhancement of the formation of TiC particles. Ultrasound assisted combustion synthesis as a simple and effective approach was proposed for synthesizing materials in this research. Copyright © 2015 Elsevier B.V. All rights reserved.

Proton irradiation studies on pure Ti and Ti-6Al-4V

Energy Technology Data Exchange (ETDEWEB)

Dutta Gupta, A. [Variable Energy Cyclotron Centre, HBNI, 1/AF Bidhannagar, Kolkata (India); Mukherjee, P., E-mail: paramita@vecc.gov.in [Variable Energy Cyclotron Centre, HBNI, 1/AF Bidhannagar, Kolkata (India); Gayathri, N.; Bhattacharyya, P.; Bhattacharya, M. [Variable Energy Cyclotron Centre, HBNI, 1/AF Bidhannagar, Kolkata (India); Sarkar, Apu [Materials Group, Bhabha Atomic Research Centre, Mumbai (India); Sen, S. [Mechanical Engineering, Jadavpur University, Kolkata (India); Mitra, M.K. [Metallurgical and Materials Engineering, Jadavpur University, Kolkata (India)

2016-11-15

Post irradiated microstructural characterisation of pure Ti and Ti-6Al-4V has been done as a function of dose using different model based techniques of X-ray diffraction line profile analysis. There is a systematic change of domain size for both the materials with dose but the microstrain within the domain remains almost unaltered. The domain size appears to be lower for pure Ti at all doses as compared to Ti-6Al-4V alloy. XRD peaks became highly asymmetric particularly at a dose of 5 × 10{sup 21} p/m{sup 2} for Ti-6Al-4V samples which is not observed for pure Ti at the same dose. This may be attributed to the segregation of alloying elements as a result of irradiation. Microhardness values increases with dose for pure Ti and then saturates at higher doses whereas microhardness values are found to decrease at higher doses for Ti-6Al-4V.

FY 2003 Scientific and Technical Reports, Articles, Papers, and Presentations

Science.gov (United States)

Fowler, B. A. (Compiler)

2004-01-01

This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center (MSFC) personnel in FY 2003. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Spring.eld, VA 22161. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

Assessing interactions of hydrophilic nanoscale TiO{sub 2} with soil water

Energy Technology Data Exchange (ETDEWEB)

Priester, John H.; Ge, Yuan; Chang, Vivian [University of California, Santa Barbara, Bren School of Environmental Science and Management (United States); Stoimenov, Peter K. [University of California, Santa Barbara, Department of Chemistry and Biochemistry (United States); Schimel, Joshua P. [University of California, Santa Barbara, Earth Research Institute (United States); Stucky, Galen D. [University of California, Santa Barbara, UC Center for the Environmental Implications of Nanotechnology (United States); Holden, Patricia A., E-mail: holden@bren.ucsb.edu [University of California, Santa Barbara, Bren School of Environmental Science and Management (United States)

2013-09-15

The implications of manufactured nanoscale materials (MNMs) in unsaturated soil are mostly unknown. Owing to its widespread use, nanoscale (n) TiO{sub 2} is expected to enter soils where its accumulation could impact soil processes. Yet fundamental information is lacking regarding nTiO{sub 2} in situ wettability, i.e., interactions with soil water that relate to nTiO{sub 2} exposure and bioavailability. To probe nTiO{sub 2} interactions with soil water, we amended a natural soil with 20 mg per g of P25 nTiO{sub 2}, a high-production, hydrophilic MNM that, based on its small size (25 nm nominal), provides ample specific surface area (SSA) for water sorption. We then measured nTiO{sub 2}-amended soil SSA, and conducted a dynamic water vapor conditioning experiment. Early time-course water sorption into soil, with and without nTiO{sub 2}, was clearly diffusional. Over 9 months, soil water content asymptotically equilibrated. However, despite amending with nTiO{sub 2} levels that increased the soil SSA by 16 %, measured water sorption rates and endpoint soil water contents were mostly unchanged by P25 nTiO{sub 2}. Our results indicate that as-manufactured hydrophilic P25 nTiO{sub 2} was hydrophobic in soil, a finding relevant to nTiO{sub 2} bioavailability and transport.

48 CFR 235.010 - Scientific and technical reports.

Science.gov (United States)

2010-10-01

....010 Scientific and technical reports. (b) For DoD, the Defense Technical Information Center is responsible for collecting all scientific and technical reports. For access to these reports, follow the... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Scientific and technical...

Study of TiC+TiN Multiple Films On Type of 316L Stainless Steel

Institute of Scientific and Technical Information of China (English)

XUE Qi; JIN Yong; HU Dong-ping; HUANG Ben-sheng; DENG Bai-quan

2004-01-01

In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported.The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainless steel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2to 2.0. The Ti [C, N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion between the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

Study of TiC＋TiN Multiple Films On Type of 316L Stainless Steel

Institute of Scientific and Technical Information of China (English)

XUEQi; JINYong; HUDong-ping; HUANGBen-sheng; DENGBai-quan

2004-01-01

In this paper, the synthesis process of TiC+TiN multiple films on super-low-carbon stainless steels is reported. The TiC layer is coated as the first layer in the multiple film, the change of growth rate of the film on the 316L Stainlesss teel is not same as the one on carbides substrates, while the mole ratio of CH4 to TiCl4 (mCH4/TiCl4) is changed from 1.2 to 2.0. The Ti [C,N], as a kind of inter-layer between TiC and TiN layers, is helpful to improve the adhesion hetween the TiC and TiN layer. The cooling rate greatly influences the quality of the adhesion between the TiC+TiN film and substrates.

Ti/TiO 2 nanotube array electrode as a new sensor to ...

Indian Academy of Sciences (India)

The Ti/TiO2 nanotube array (Ti-NTA) electrode was prepared by anodizing of the Ti foil ... and the pH=3.0 and =1.0 V (vs. reference electrode) were determined as the ... It was found that the photocurrent of EG was linearly dependent on the ...

Stepwise Ti-Cl, Ti-CH3, and Ti-C6H5 bond dissociation enthalpies in bis(pentamethylcyclopentadienyl)titanium complexes

NARCIS (Netherlands)

Dias, Alberto R.; Salema, Margarida S.; Martinho Simões, Jose A.; Pattiasina, Johannes W.; Teuben, Jan H.

1988-01-01

Reaction-solution calorimetric studies involving the complexes Ti[η5-C5(CH3)5]2(CH3)2, Ti[η5-C5(CH3)5]2(CH3), Ti[η5-C5(CH3)5]2(C6H5), Ti[η5-C5(CH3)5]2Cl2, and Ti[η5-C5(CH3)5]2Cl, have enabled derivation of titanium-carbon and titanium-chlorine stepwise bond dissociation enthalpies in these species.

Information management systems for integrating the technical data and regulatory requirements of environmental restoration activities

International Nuclear Information System (INIS)

Geffen, C.A.; Garrett, B.A.; Walter, M.B.

1990-03-01

Current environmental regulations require that comprehensive planning be conducted before remediating a hazardous waste site to characterize the nature and extent of site contamination, calculate the risk to the public, and assess the effectiveness of various remediation technologies. Remediation of Department of Energy (DOE) sites contaminated with hazardous or mixed wastes will require the effective integration of scientific and engineering data with regulatory and institutional requirements. The information management challenge presented by waste site cleanup activities goes beyond merely dealing with the large quantity of data that will be generated. The information must be stored, managed, and presented in a way that provides some consistency in approach across sites, avoids duplication of effort, and facilitates responses to requests for information from the regulators and the public. This paper provides background information on the regulatory requirements for data gathering and analysis for environmental restoration activities, and outlines the data and information management requirements for completing the pre-remediation phases of an environmental restoration project. Information management systems for integrating the regulatory and institutional requirements of the environmental restoration process with the technical data and analysis requirements are also described. 7 refs

钛合金表面激光熔覆NiCrBSi(Ti)-TiC涂层%Study on laser cladding of NiCrBSi (Ti)-TiC metal-ceramiccomposite coatings on titanium alloy

Institute of Scientific and Technical Information of China (English)

孙荣禄; 郭立新; 董尚利; 杨德庄

2001-01-01

在TC4合金表面进行了激光熔覆NiCrBSi-TiC,Ti-TiC金属陶瓷复合涂层的试验,对涂层的组织和显微硬度进行了分析和测试.结果表明,NiCrBSi-TiC涂层的组织是在初晶γ-Ni和γ-Ni,Ni3B,M23(CB)6,CrB多元共晶的基底上均匀地分布着TiC颗粒,在激光熔覆过程中TiC颗粒只是边缘发生了溶解或熔化;在Ti-TiC涂层中,TiC颗粒全部溶解或熔化,冷却时以枝晶形式重新析出.NiCrBSi-TiC涂层的显微硬度(HV900～1100)明显高于Ti-TiC的涂层的显微硬度(HV500～700).

A case study evaluation of a Critical Care Information System adoption using the socio-technical and fit approach.

Science.gov (United States)

Yusof, Maryati Mohd

2015-07-01

Clinical information systems have long been used in intensive care units but reports on their adoption and benefits are limited. This study evaluated a Critical Care Information System implementation. A case study summative evaluation was conducted, employing observation, interview, and document analysis in operating theatres and 16-bed adult intensive care units in a 400-bed Malaysian tertiary referral centre from the perspectives of users (nurses and physicians), management, and information technology staff. System implementation, factors influencing adoption, fit between these factors, and the impact of the Critical Care Information System were evaluated after eight months of operation. Positive influences on system adoption were associated with technical factors, including system ease of use, usefulness, and information relevancy; human factors, particularly user attitude; and organisational factors, namely clinical process-technology alignment and champions. Organisational factors such as planning, project management, training, technology support, turnover rate, clinical workload, and communication were barriers to system implementation and use. Recommendations to improve the current system problems were discussed. Most nursing staff positively perceived the system's reduction of documentation and data access time, giving them more time with patients. System acceptance varied among doctors. System use also had positive impacts on timesaving, data quality, and clinical workflow. Critical Care Information Systems is crucial and has great potentials in enhancing and delivering critical care. However, the case study findings showed that the system faced complex challenges and was underutilised despite its potential. The role of socio-technical factors and their fit in realizing the potential of Critical Care Information Systems requires continuous, in-depth evaluation and stakeholder understanding and acknowledgement. The comprehensive and specific evaluation

AUDIT TI UNTUK MENEMUKAN POLA BEST PRACTICE PENGELOLAAN TI PADA PERBANKAN (STUDI KASUS PT. BANK SYARIAH MANDIRI CABANG DENPASAR

Directory of Open Access Journals (Sweden)

Shofwan Hanief

2015-11-01

Full Text Available Audit TI untuk Menemukan Pola Best PracticePengelolaan TI pada Perbankan(Studi Kasus PT. Bank Syariah Mandiri CabangDenpasarShofwan HaniefEmail : zwanhanf27@gmail.comAbstrakPT. Bank Syariah Mandiri cabang Denpasar sudah menggunakan TI untuk menunjang prosespelayanan yang dilakukan. Sampai saat ini TI yang ada belum pernah dilakukan penilaian sejauhmana proses-proses tersebut dapat berjalan dengan baik. Agar implementasi IT Governanceyang ada di PT. Bank Syariah Mandiri berlangsung secara efektif, organisasi perlu menilai sejauhmana IT Governance yang sekarang berlangsung dan mengidentifikasi peningkatan yang dapatdilakukan. Pengunaan model maturity (kematangan dalam hal ini akan memudahkan dalampenilaian dengan cara pendekatan yang terstruktur terhadap skala yang mudah dimengerti dankonsisten. Salah satu alat yang digunakan untuk IT Governance adalah COBIT (ControlObjectives for Information and Related Technology yaitu suatu model standar pengelolaan TIyang dapat membantu pihak manajemen dan pemakai untuk menjembatani kesenjangan antararesiko bisnis, kebutuhan kontrol, dan permasalahan teknis.Analisis untuk tingkat kematangandilakukan dengan cara membandingkan tingkat kematangan yang ada pada saat ini dengantingkat kematangan yang dituju.Tingkat kematangan saat ini (current maturity level untuk setiapproses yang ada pada domain Deliver and Support rata-rata berada pada level 2, walaupun adasebagian kecil yang berada di level 3, bahkan di level 1. Hal ini dapat dikatakan bahwa prosestata kelola TI di PT. Bank Syariah Mandiri cabang Denpasar sudah dilakukan tetapi belumberjalan secara optimal.

Effect Of Ti Powder Addition On The Fabrication Of TiO2 Nanopowders

Directory of Open Access Journals (Sweden)

Raihanuzzaman R.M.

2015-06-01

Full Text Available Sintered samples of Ti added TiO2 nanopowders were fabricated by combined application of magnetic pulsed compaction (MPC and sintering. The effect of Ti nano powder on density, shrinkage and hardness of the samples were investigated as part of the study. The optimum processing conditions were found to be around 0.5 GPa MPC pressure and 1450°C sintering temperature, illustrating maximum density, hardness and minimum shrinkage. High pressure compaction using MPC was found to enhance density with increasing MPC pressure up to 0.9 GPa, and significantly reduce the total shrinkage (about 16% in this case in the sintered bulks compared to other general processes (about 18%. While sintered samples blended with micro Ti showed presence of microstructural cracks, the samples with 1-2% nano Ti had less or no cracks on them. Overall, the inclusion of nano Ti indicated improvement in mechanical properties of TiO2 nanopowders sintered preforms as opposed to micro Ti-added TiO2.

Development of JNC geological disposal technical information integration system for geological environment field

International Nuclear Information System (INIS)

Tsuchiya, Makoto; Ueta, Shinzo; Ohashi, Toyo

2004-02-01

Enormous data on geology, geological structure, hydrology, geochemistry and rock properties should be obtained by various investigation/study in the geological disposal study. Therefore, 'JNC Geological Disposal Technical Information Integration System for Geological Environment Field' was developed in order to manage these data systematically and to support/promote the use of these data for the investigators concerned. The system is equipped with data base to store the information of the works and the background information of the assumptions built up in the works on each stage of data flow ('instigative', → 'data sampling' → interpretation' → conceptualization/modeling/simulation' → 'output') in the geological disposal study. In this system the data flow is shown as 'plan' composed of task' and 'work' to be done in the geological disposal study. It is possible to input the data to the database and to refer data from the database by using GUI that shows the data flow as 'plan'. The system was installed to the server computer possessed by JNC and the system utilities were checked on both the server computer and client computer also possessed by JNC. (author)

Corrosion Behavior of Ti/TiN Film Coated on AISI 304 Stainless Steel

Energy Technology Data Exchange (ETDEWEB)

Choe, Han Cheol [Kwangyang College, Gwangyang (Korea, Republic of); Park, Ji Yoon; Kim, Kwan Hyu [Chonnam National University, Gwangju (Korea, Republic of)

2000-06-15

Effects of the Ti content and the presence of Ti underlayer on the corrosion behaviors of TiN coated AISI 304 stainless steel have been studied. The stainless steel containing 0.1{approx}1.0 wt% Ti were melted with a vacuum furnace and heat treated at 1050 .deg. C for 1hr for solutionization. The specimens were coated with Ti and TiN with thickness of 1 {mu}m and 2 {mu}m respectively by electron-beam physical vapour deposition (EB-PVD) method. The microstructures and phase analysis were conducted by using SEM and WDS. The coated films showed fine columnar structure. The corrosion potential obtained from the anodic polarization curves measured in H{sub 2}SO{sub 4} solution increased in proportion to the Ti content of substrate and was much higher in the specimen coated with Ti underlayer compared to the specimen without Ti underlayer. The potential-time and the current-time curves which were obtained in 0.1M H{sub 2}SO{sub 4} + 0.1M HCI solution showed that both the increase in Ti content and the presence of Ti underlayer increased the potential and decreased the current density resulting in a dense passive film and a suppress of pit formation respectively.

Technical resource documents and technical handbooks for hazardous-wastes management

Energy Technology Data Exchange (ETDEWEB)

Schomaker, N.B.; Bliss, T.M.

1986-07-01

The Environmental Protection Agency is preparing a series of Technical Resource Documents (TRD's) and Technical Handbooks to provide best engineering control technology to meet the needs of the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) respectively. These documents and handbooks are basically compilation of research efforts of the Land Pollution Control Division (LPCD) to date. The specific areas of research being conducted under the RCRA land disposal program relate to laboratory, pilot and field validation studies in cover systems, waste leaching and solidification, liner systems and disposal facility evaluation. The technical handbooks provide the EPA Program Offices and Regions, as well as the states and other interested parties, with the latest information relevant to remedial actions.

Study of a Ti Ni-based shape memory alloy aiming applications in pipeline connections of the oil and gas industry; Estudo de uma liga base Ti-Ni com memoria de forma visando aplicacoes em conexoes de tubulacoes na industria do petroleo e gas

Energy Technology Data Exchange (ETDEWEB)

Silva, M.M. da; Silva, N.J. da; Gomes, A.A.C.; Reis, R.P.B.; Araujo, C.J. de; Santos, M.A. dos [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Lab. Multidisciplinar de Materiais e Estruturas Ativas (LaMMEA)], e-mail: carlos@dem.ufcg.edu.br

2006-07-01

The objective of this paper is to study the technical feasibility of a TiNi-based Shape Memory Alloy (SMA) with potential application in connections of the oil and gas Sector. The employment of this alloy would increase the reliability of these unions. Thus, a 45,0 Ti-55,0 Ni (% wt) SMA has been manufactured through the plasma skull melting and with subsequent conformation by the Push-Pull method. Samples of this SMA were heat treated at 1173 K during 900s, followed by water quenching. These samples were characterized by optic microscopy, microhardness, differential scanning calorimetry (DSC), and force generation tests. The obtained TiNi SMA has presented an important wide temperature hysteresis. The generated forces substantiate the potential application of these alloys in connection systems of the oil and gas Sector. (author)

STAIRS/VS in a central institute for scientific and technical information

International Nuclear Information System (INIS)

Pulew, W.M.; Chlebarow, J.A.; Boitschew, B.B.; Kurtew, I.D.

1978-01-01

STAIRS/VS has been installed on an IBM System/370-B5 in the computer centre of the central institute for scientific and technical information (ZINTI) in Sofia since 1975. Besides literature documentation, STAIRS/VS is also used for project documentation in order to supervise projects and their progress. Two types of data banks result from this problem in two parts differing in structure. Internal data as well as external data from magnetic tape service enter the STAIRS/VS data bank. The processing of texts in Cyrillic applied here for the first time is completely new for STAIRS/VS operation. Hence certain modifications for STAIRS/VS were made: STAIRS/VS was supplemented by a series of programmes for project supervision. The data acquisition as well as the change or supplementation of the documents already stored in STAIRS/VS mainly run via VIDEO/370. Besides the STAIRS/VS standard information on high-speed printers or on magnetic tape, special printing forms were developed. Parties interested in STAIRS/VS are supplied with a SDI service produced in batch process based on magnetic tape service; it is made in special size. The appropriate data banks are accordingly available for on-line research. (orig.) [de

More cloud for TiU

Directory of Open Access Journals (Sweden)

Marc van den Berg

2012-03-01

Full Text Available After a long period of developing library systems in house, Tilburg University (TiU decided to buy a new integrated library system (ILS and at the same time go for a cloud solution. Functionality, cost and vision of the future of scholarly communication were weighed up, and OCLC came out as the winner: TiU is now implementing OCLC’s ‘Web-scale Management Services’ (WMS and WorldCat Local (WCL. The road leading to that decision is described and some issues to be resolved are mentioned. The implementation project is intended to end in June 2012. Additionally, a short description is given of a possible future Dutch national information infrastructure for scholarly output that consists of just four major building blocks which partly already exist.

Electronic Structures and Bonding Properties of Ti2AlC and Ti3AlC2

Institute of Scientific and Technical Information of China (English)

MIN Xinmin; REN Yi

2007-01-01

The relation among electronic structure, chemical bond and property of Ti2AlC, Ti3AlC2 and doping Si into Ti2AlC was studied by density function and the discrete variation (DFT-DVM) method. After adding Si into Ti2AlC, the interaction between Si and Ti is weaker than that between Al and Ti, and the strengths of ionic and covalent bonds decrease both. The ionic and covalent bonds in Ti3AlC2, especially in Ti-Al, are stronger than those in Ti2AlC. Therefore, in synthesis of Ti2AlC, the addition of Si enhances the Ti3AlC2 content instead of Ti2AlC. The density of state (DOS) shows that there is mixed conductor characteristic in Ti2AlC and Ti3AlC2. The DOS of Ti3AlC2 is much like that of Ti2AlC. Ti2SixAl1-x C has more obvious tendency to form a semiconductor than Ti2AlC, which is seen from the obvious difference of partial DOS between Si and Al3p.

76 FR 18573 - Notice of Proposed Information Collection; Comment Request; National Resource Bank

Science.gov (United States)

2011-04-04

... December 16, 2009) funds technical assistance for HUD programs under the Transformation Initiative (TI... business cluster and job market analysis, to name a few. Agency form numbers, if applicable: SF-424, SF...

合金元素对电弧熔炼TiC/Ti-6Al-4V复合材料中TiC生长形态的影响%Effects of Alloying Elements on Growth and Morphology of TiC in Arc-Melted TiC/Ti-6Al-4V Composites

Institute of Scientific and Technical Information of China (English)

曹磊; 王宏伟; 邹鹑鸣; 魏尊杰

2010-01-01

采用非自耗电弧熔炼制备含不同微合金元素的10vol%TiC/Ti-6Al-4V复合材料,研究不同的微量合金元素对复合材料中TiC形态的影响.结果表明,原始铸态复合材料中TiC形态主要是粗大且发达的枝晶状.而基体中加入0.3%(质量分数,下同)的Sn元素后,TiC生长被抑制,TiC形态变为细小分散的颗粒状;0.3%的Ni被加入后,增大了TiC的结晶区间,使TiC枝晶生长变得更加发达;而0.3%的Nb元素的加入,则减小了TiC的结晶区间,从而减少了初晶TiC数量,促进了共晶TiC的形成.

Effect of TiC content on the microstructure and properties of Ti3SiC2-TiC composites in situ fabricated by spark plasma sintering

International Nuclear Information System (INIS)

Zhang Jianfeng; Wang Lianjun; Jiang Wan; Chen Lidong

2008-01-01

Spark plasma sintering technique was used to in situ fabricate high dense Ti 3 SiC 2 -TiC composites. The calculated TiC volume content from X-ray diffraction (XRD) is close to the theoretical one. It is found from fracture surface observation that TiC is about 1 μm, and Ti 3 SiC 2 is about 2-10 μm in grain size. The fracture modes consist of intergranular mainly for Ti 3 SiC 2 and transgranular fracture mainly for TiC. With the increasing of TiC volume content, Vickers hardness increases to the maximum value of 13 GPa for Ti 3 SiC 2 -40 vol.%TiC. Fracture toughness and flexural strength of the composites are also improved compared with those of monolithic Ti 3 SiC 2 except for Ti 3 SiC 2 -40 vol.%TiC composite. The main reasons for the sudden decrease of fracture toughness and flexural strength of Ti 3 SiC 2 -40 vol.%TiC composite can be attributed to the relatively lower density, some clusters of TiC in the composite and the transition of fracture mode from intergranular to transgranular. The thermal conductivities decreased with the addition of TiC. The minimum thermal conductivity is 22 W m deg. C -1 for Ti 3 SiC 2 -40 vol.%TiC composite

Atomic Layer-Deposited TiO2 Coatings on NiTi Surface

Science.gov (United States)

Vokoun, D.; Racek, J.; Kadeřávek, L.; Kei, C. C.; Yu, Y. S.; Klimša, L.; Šittner, P.

2018-02-01

NiTi shape-memory alloys may release poisonous Ni ions at the alloys' surface. In an attempt to prepare a well-performing surface layer on an NiTi sample, the thermally grown TiO2 layer, which formed during the heat treatment of NiTi, was removed and replaced with a new TiO2 layer prepared using the atomic layer deposition (ALD) method. Using x-ray photoelectron spectroscopy, it was found that the ALD layer prepared at as low a temperature as 100 °C contained Ti in oxidation states + 4 and + 3. As for static corrosion properties of the ALD-coated NiTi samples, they further improved compared to those covered by thermally grown oxide. The corrosion rate of samples with thermally grown oxide was 1.05 × 10-5 mm/year, whereas the corrosion rate of the ALD-coated samples turned out to be about five times lower. However, cracking of the ALD coating occurred at about 1.5% strain during the superelastic mechanical loading in tension taking place via the propagation of a localized martensite band.

Technical Training: WBTechT offers online training

CERN Multimedia

Monique Duval

2005-01-01

CERN Technical Training 2005 The 2005 CERN Web-Based Technical Training portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications and 90.- CHF for technical applications for three months' unlimited access. Visit the WBTechT portal or http://www.cern.ch/TechnicalTraining, and contact Technical.Training@cern.ch or your DTOs to find out more information. ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

Technical Training: WBTechT offers online training

CERN Multimedia

Monique Duval

2005-01-01

CERN Technical Training 2005 The 2005 CERN Web-Based Technical Training (WBTechT) portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications and 90.- CHF for technical applications for three months' unlimited access. Visit the WBTechT portal or http://www.cern.ch/TechnicalTraining, and contact Technical.Training@cern.ch or your DTO to find out more information. ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

Incorporation of chromium into TiO2 nanopowders

International Nuclear Information System (INIS)

Kollbek, Kamila; Sikora, Marcin; Kapusta, Czesław; Szlachetko, Jakub; Radecka, Marta; Lyson-Sypien, Barbara; Zakrzewska, Katarzyna

2015-01-01

Highlights: • Nanopowders of TiO 2 :Cr with different amount of Cr dopant were obtained by flame spray synthesis, FSS. • Increase in the optical absorption and a shift of the absorption edge were observed upon Cr doping. • HERFD-XANES measurements indicated that the average valence state of titanium ions was preserved. • Increasing magnetic susceptibility of a paramagnetic character was observed upon Cr doping. - Abstract: The paper reports on the results of a study of optical, electronic and magnetic properties of TiO 2 nanopowders doped with Cr ions. Diffused reflectance spectra reveal an increase in the optical absorption and a shift of the absorption edge towards lower energies upon Cr doping. Direct information on the Ti electronic state and the symmetry of its nearest environment is obtained from XANES Ti K-edge spectra. Magnetic behaviour is probed by means of the temperature dependence of DC magnetic susceptibility. Increasing magnetic susceptibility of a paramagnetic character is observed upon increasing chromium doping. The Curie constant of TiO 2 :10 at.% Cr sample (0.12 emu K/mol Oe) is lower than that expected for Cr 3+ (0.1875 emu K/mol Oe) possibly due to the appearance of Cr 4+ or the presence of the orbital contribution to the magnetic moment

Effect of Ti solute on the recovery of cold-rolled V-Ti alloys

International Nuclear Information System (INIS)

Leguey, T.; Munoz, A.; Pareja, R.

1999-01-01

The recovery characteristics of cold-rolled pure V and V-Ti alloys with compositions of 0.3, 1 and 4.5 at.% Ti have been investigated by positron annihilation spectroscopy. The recovery is accomplished in two stages. Fifty percent cold rolling induces the formation of microvoids in V-0.3Ti and V-1Ti but not in V-4.5Ti. The first recovery stage in pure V, V-0.3Ti and V-1Ti starts with the dissolution of microvoids. The recovery curves of the annihilation parameters for the alloys indicate the formation of Ti-rich precipitates during the first recovery stage. These precipitates act as very efficient vacancy sinks. The second recovery stage starting for annealing temperatures above ≅1150 K is attributed to annealing of vacancies associated to the precipitates. (orig.)

Mechanical Engineering Department. Technical review

Energy Technology Data Exchange (ETDEWEB)

Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

Mechanical engineering department technical review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

Mechanical Engineering Department Technical Review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

Mechanical Engineering Department. Technical review

International Nuclear Information System (INIS)

Simecka, W.B.; Condouris, R.A.; Talaber, C.

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

CERN Technical Training 2006 - WBTechT offers online training

CERN Multimedia

2006-01-01

The 2006 CERN Web-Based Technical Training (WBTechT) portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications (e.g. Microsoft Office Suite, Frontpage, Dreamweaver, Illustrator, Photoshop) and 90.- CHF for technical applications (e.g. Unix, Oracle, Java, JavaScript, C, C++) for three months'unlimited access. Visit the WBTechT portal, or the WBTechT information page at http://www.cern.ch/TechnicalTraining, and contact technical.training@cern.ch or your DTO to find out more information. ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING technical.training@cern.ch

Dielectric enhancement of BaTiO3/SrTiO3 superlattices with embedded Ni nanocrystals

International Nuclear Information System (INIS)

Xiong Zhengwei; Sun Weiguo; Wang Xuemin; Jiang Fan; Wu Weidong

2012-01-01

Highlights: ► The BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs were successfully fabricated by L-MBE. ► The influence with the various concentrations of Ni nanocrystals embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. ► The BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss compared with the pure BaTiO 3 /SrTiO 3 superlattices. ► The dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory. - Abstract: The self-organized Ni nanocrystals (NCs) were embedded in BaTiO 3 /SrTiO 3 superlattices using laser molecular beam epitaxy (L-MBE). The stress of the composite films was increased with the increasing concentration of embedded Ni NCs, as investigation in stress calculation. The influence with the various concentrations of Ni NCs embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. The internal stress of the films was too strong to epitaxial growth of BaTiO 3 /SrTiO 3 superlattices. Compared with the pure BaTiO 3 /SrTiO 3 superlattices, the BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss. Furthermore, the dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory.

nTiO_2 mass transfer and deposition behavior in an aquatic environment

International Nuclear Information System (INIS)

Wei, Xiuzhen; He, Junhui; Wang, Meng; Fang, Jinfeng; Chen, Jinyuan; Lv, Bosheng

2016-01-01

Nano-TiO_2 (nTiO_2) is widely used in industry, and some of it is inevitably released into natural aquatic environments. nTiO_2 can be deposited on the streambed or transported along the stream and streambed, and it can also undergo exchange-transfer processes in these systems. The behavior of nTiO_2 in rivers includes deposition-transfer processes in the stream and exchange-transfer processes between the stream and streambed. In this work, the deposition, mass transfer, exchange, and aggregation behavior of nTiO_2 in a simulated river were studied as a function of the solution pH, stream velocity, and anionic, cationic, and neutral surfactant concentrations. In these experiments, a recirculating flume was used to simulate a natural stream. The nTiO_2 deposition and aggregation phenomena in the river and streambed were characterized. Of the three surfactants studied, the anionic surfactant enhanced the nTiO_2 stability in the river and limited its aggregation most effectively, resulting in slow nTiO_2 deposition and nTiO_2 transport over long distances. This study provides information about nanoparticle transport phenomena in simulated natural aquatic systems.

Phase equilibria among α-Fe(Al, Cr, Ti), liquid and TiC and the formation of TiC in Fe3Al-based alloys

International Nuclear Information System (INIS)

Kobayashi, Satoru; Schneider, Andre; Zaefferer, Stefan; Frommeyer, Georg; Raabe, Dierk

2005-01-01

In the context of the development of high-strength Fe 3 Al-based alloys, phase equilibria among α-Fe(Al, Cr, Ti), liquid and TiC phases in the Fe-Al-Cr-Ti-C quinary system and the formation of TiC were determined. A pseudo-eutectic trough (L α + L + TiC) exists at 1470 deg C at around Fe-26Al-5Cr-2Ti-1.7C on the vertical section between Fe-26Al-5Cr (α) and Ti-46C (TiC) in at.%. Large faceted TiC precipitates form from the melt after the formation of primary α phase even in hypoeutectic alloys. The TiC formation is thought to be due to the composition change of the liquid towards the hypereutectic compositions by solidification of the primary α. In order to remove the faceted TiC, which are unfavourable for strengthening the material, two different processing routes have been successfully tested: (i) solidification with an increased rate to reduce the composition variation of the liquid during solidification, and (ii) unidirectional solidification to separate the light TiC precipitates from the melt

A study of TiB2/TiB gradient coating by laser cladding on titanium alloy

Science.gov (United States)

Lin, Yinghua; Lei, Yongping; Li, Xueqiao; Zhi, Xiaohui; Fu, Hanguang

2016-07-01

TiB2/TiB gradient coating has been fabricated by a laser cladding technique on the surface of a Ti-6Al-4V substrate using TiB2 powder as the cladding material. The microstructure and mechanical properties of the gradient coating were analyzed by SEM, EPMA, XRD, TEM and an instrument to measure hardness. With the increasing distance from the coating surface, the content of TiB2 particles gradually decreased, but the content of TiB short fibers gradually increased. Meanwhile, the micro-hardness and the elastic modulus of the TiB2/TiB coating showed a gradient decreasing trend, but the fracture toughness showed a gradient increasing trend. The fracture toughness of the TiB2/TiB coating between the center and the bottom was improved, primarily due to the debonding of TiB2 particles and the high fracture of TiB short fibers, and the fracture position of TiB short fiber can be moved to an adjacent position. However, the debonding of TiB2 particles was difficult to achieve at the surface of the TiB2/TiB coating.

Microstructure and wear of in-situ Ti/(TiN + TiB) hybrid composite layers produced using liquid phase process

Energy Technology Data Exchange (ETDEWEB)

Yazdi, R., E-mail: ryazdi@ut.ac.ir; Kashani-Bozorg, S.F.

2015-02-15

Tungsten inert gas (TIG) technique was conducted on commercially pure (CP)-Ti substrate, which was coated with h-BN-based powder mixture prior to the treatment. The treated surfaces were evaluated and characterized by means of scanning electron microscope (SEM), X-ray diffraction analysis, and electron dispersive spectrometry (EDS). The microhardness and wear experiment were also performed by using a microhardness machine and pin-on-disk tribometer. As h-BN reacted with titanium, an in-situ hybrid composite layer was formed showing near stoichiometric dendrites of TiN, platelets of TiB and interdendritic regions of α′-Ti martensite crystal structures. The population level of TiN and TiB regions were found to increase using a pre-placed powder mixture with greater h-BN content. However, the fabricated layers exhibited cracking and porosity; these were minimized by adjusting arc energy density and h-BN content of powder mixture. The microhardness value of the fabricated hybrid composite layers was found to be in the range of ∼650 HV{sub 0.2}–1000 HV{sub 0.2}; this is three to five times higher than that of the untreated CP-Ti substrate. In addition, the in-situ hybrid composite layers exhibited superior wear behavior over CP-Ti substrate; this is attributed to the formation of newly formed ceramic phases in the solidified surface layers and good coherent interface between the composite layer and CP-substrate. Meanwhile, severe adhesive wear mechanism of CP-titanium surface changed to mild abrasive one as a result of surface treatment. - Highlights: • In-situ Ti/(TiN + TiB) hybrid composite layers were synthesized by TIG processing on commercially pure titanium. • The microstructure features were characterized by several methods. • Microhardness enhanced three to five times higher than that of the CP-Ti substrate after surface modification. • The fabricated composite layers improved wear resistance of CP-titanium. • Severe adhesive wear mechanism of

Influence of TiC Content on Microstructure and Properties of TiC/Cu Composite%TiC含量对TiC/Cu复合材料组织与性能的影响

Institute of Scientific and Technical Information of China (English)

李小池; 杨巧

2017-01-01

采用粉末冶金法制备了TiC/Cu复合材料,研究不同TiC含量对TiC/Cu复合材料组织与拉伸性能的影响,并利用扫描电镜、金相显微镜等对样品的表面形貌和拉伸断口形貌进行分析.结果表明,TiC与基体结合紧密且在基体中分布均匀;随着增强相TiC含量的增加,TiC/Cu复合材料的抗拉强度先增大后降低;TiC的加入明显阻碍了基体晶粒长大;当TiC质量分数为2％时,强化效果较好,TiC/Cu复合材料的塑性较好.

Behavior of A NbTi very fine filament composite with current feed in the technical range

International Nuclear Information System (INIS)

Asdente, M.; Ottoboni, V.; Ripamonti, G.; Zannella, S.

1985-01-01

Self-field losses have been measured on a NbTi multifilamentary wire with very fine filaments suitable for use in ac superconducting equipment working at industrial frequency. The loss trends as functions of current intensity and frequency as well as the comparison of the losses in a coil show that they are essentially of hysteretic nature

Early stages of the mechanical alloying of TiC–TiN powder mixtures

International Nuclear Information System (INIS)

Mura, Giovanna; Musu, Elodia; Delogu, Francesco

2013-01-01

The present work focuses on the alloying behavior of TiC–TiN powder mixtures submitted to mechanical processing by ball milling. Accurate X-ray diffraction analyses indicate a progressive modification of the unit cell parameters of the TiC and TiN phases, suggesting the formation of TiC- and TiN-rich solid solutions with an increasingly larger content of solutes. Once the discrete character of the mechanical treatment is taken into due account, the smooth change of the unit cell parameters can be explained by a sequence of mutual dissolution stages related to individual collisions. At each collision, the average chemical composition of small amounts of TiC- and TiN-rich phases changes discontinuously. The discontinuous changes can be tentatively ascribed to local mass transport processes activated by the mechanical deformation of powders at collisions. -- Highlights: ► Mechanically processed TiC–TiN powder mixtures form two solid solutions. ► An analytical model was developed to describe the mechanical alloying kinetics. ► The amount of powder alloyed at collision was indirectly estimated. ► A few nanomoles of material participate in the alloying process at each collision. ► The chemical composition of the solid solutions was shown to change discontinuously.

Incorporation of dysprosium ions into PbTiO3 ferroelectric ceramic system

Directory of Open Access Journals (Sweden)

A. Peláiz-Barranco

2015-03-01

Full Text Available A structural analysis concerning the incorporation of dysprosium into A- and/or B-sites of the lead titanate is shown. The two "boundary" refinements are presented, i.e., Dy2+ substitutes for Pb2+ (Dy3+ substitutes for Ti4+ and Dy3+ substitutes for Pb2+ (Dy3+ substitutes for Ti4+. The results offer quantitative information about the incorporation into both crystallographic sites. The increase of Dy3+ fraction into B-site provides the increase of the Ti4+ atomic displacement along the [001] direction and the tetragonal distortion.

Effects of strong interactions between Ti and ceria on the structures of Ti/CeO2.

Science.gov (United States)

Yao, Xiao-Dan; Zhu, Kong-Jie; Teng, Bo-Tao; Yu, Cao-Ming; Zhang, Yun-Lei; Liu, Ya; Fan, Maohong; Wen, Xiao-Dong

2016-11-30

The effects of strong interactions between Ti and ceria on the structures of Ti/CeO 2 (111) are systematically investigated by density functional theory calculation. To our best knowledge, the adsorption energy of a Ti atom at the hollow site of CeO 2 is the highest value (-7.99 eV) reported in the literature compared with those of Au (-0.88--1.26 eV), Ag (-1.42 eV), Cu (-2.69 eV), Pd (-1.75 eV), Pt (-2.62 eV) and Sn (-3.68 eV). It is very interesting to find that Ti adatoms disperse at the hollow site of CeO 2 (111) to form surface TiO x species, instead of aggregating to form Ti metal clusters for the Ti-CeO 2 interactions that are much stronger than those of Ti-Ti ones. Ti adatoms are completely oxidized to Ti 4+ ions if they are monatomically dispersed on the next near hollow sites of CeO 2 (111) (xTi-NN-hollow); while Ti 3+ ions are observed when they locate at the near hollow sites (xTi-N-hollow). Due to the electronic repulsive effects among Ti 3+ ions, the adsorption energies of xTi-N-hollow are slightly weaker than those of xTi-NN-hollow. Simultaneously, the existence of unstable Ti 3+ ions on xTi-N-hollow also leads to the restructuring of xTi-N-hollow by surface O atoms of ceria transferring to the top of Ti 3+ ions, or oxidation by O 2 adsorption and dissociation. Both processes improve the stability of the xTi/CeO 2 system by Ti 3+ oxidation. Correspondingly, surface TiO 2 -like species form. This work sheds light into the structures of metal/CeO 2 catalysts with strong interactions between the metal and the ceria support.

Crystal structure of transition metal halides TiCl4, α-TiCl3, WCl4 and TiI2

International Nuclear Information System (INIS)

Troyanov, S.I.; Snigireva, E.M.

2000-01-01

Crystal structures of TiCl 4 , α-TiCl 3 , WCl 4 and TiI 2 are determined by x-ray diffraction method. For crystalline WCl 4 general for phases of this type space group C2/m is confirmed. Linear chains of WCl 6 octahedrons joined through the opposite edges exist in structure. Short W-W distances (2.69 A) in linear chains differentiate the structure of WCl 6 . Laminar structure of TiI 2 is belongs to CdI 2 structural type. Iodine atoms form slightly distorted hexagonal face-centered packing, titanium atoms fill up octahedral hollows in two-layer packing of iodine atoms with Ti-I distances equal 2.903 A [ru

Fabrication and Mechanical Properties of Nanostructured TiC-TiAl by the Pulsed Current Activated Sintering

Energy Technology Data Exchange (ETDEWEB)

Kwak, Bong-Won; Shon, In-Jin [Chonbuk National University, Chonbuk (Korea, Republic of); Kim, Byung-Su [Korea Institute of Geoscience and Mineral Resources, Daejeon (Korea, Republic of); Yoon, Jin-Kook; Hong, Kyung-Tae [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

2016-08-15

TiC-Co or TiC-Ni hard materials have been used for cutting tools. However, the high cost and the low hardness of Ni or Co, and the low corrosion resistance of the TiC-Ni and TiC-Co cermets have generated interest in recent years in using them as alternative binder phases. In this study, TiAl was used as a novel binder and consolidated by the pulsed current activated sintering(PCAS) method. Nanopowders of TiC and TiAl were fabricated using high energy ball milling. Highly dense TiC-TiAl hard materials with a relative density of up to 99.5% were sintered within three min by PCAS. Not only the hardness but also the fracture toughness of the TiC-10 vol%TiAl were better than those of TiC-10 vol%Ni or TiC-10 vol%Co.

Fabrication and Mechanical Properties of Nanostructured TiC-TiAl by the Pulsed Current Activated Sintering

International Nuclear Information System (INIS)