WorldWideScience

Sample records for tar sands oil

  1. Production of oil from Intermountain West tar sands deposits

    Energy Technology Data Exchange (ETDEWEB)

    Glassett, J.M.; Glassett, J.A.

    1976-03-01

    Six tar sand deposits in the Intermountain West, each containing more than one billion barrels of oil in place, are identified. All of these deposits are in eastern Utah and contain a total of twenty-eight billion barrels of oil. The names of the six deposits arranged in descending order of desirability for large-scale surface-mining oil recovery operations are as follows: Sunnyside, Tar Sand Triangle, Asphalt Ridge, P.R. Spring, Circle Cliffs, and Hill Creek. An overview of each deposit is presented including geology, surface-mining variables, chemical processing variables, environmental aspects, and economics. A comparison of Utah tar sands and Athabasca, Alberta, Canada tar sands is also presented.

  2. In situ recovery of oil from Utah tar sand: a summary of tar sand research at the Laramie Energy Technology Center

    Energy Technology Data Exchange (ETDEWEB)

    Marchant, L.C.; Westhoff, J.D.

    1985-10-01

    This report describes work done by the United States Department of Energy's Laramie Energy Technology Center from 1971 through 1982 to develop technology for future recovery of oil from US tar sands. Work was concentrated on major US tar sand deposits that are found in Utah. Major objectives of the program were as follows: determine the feasibility of in situ recovery methods applied to tar sand deposits; and establish a system for classifying tar sand deposits relative to those characteristics that would affect the design and operation of various in situ recovery processes. Contents of this report include: (1) characterization of Utah tar sand; (2) laboratory extraction studies relative to Utah tar sand in situ methods; (3) geological site evaluation; (4) environmental assessments and water availability; (5) reverse combustion field experiment, TS-1C; (6) a reverse combustion followed by forward combustion field experiment, TS-2C; (7) tar sand permeability enhancement studies; (8) two-well steam injection experiment; (9) in situ steam-flood experiment, TS-1S; (10) design of a tar sand field experiment for air-stream co-injection, TS-4; (11) wastewater treatment and oil analyses; (12) economic evaluation of an in situ tar sand recovery process; and (13) appendix I (extraction studies involving Utah tar sands, surface methods). 70 figs., 68 tabs.

  3. Paleontological overview of oil shale and tar sands areas in Colorado, Utah, and Wyoming.

    Energy Technology Data Exchange (ETDEWEB)

    Murphey, P. C.; Daitch, D.; Environmental Science Division

    2009-02-11

    In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the ''Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005,'' Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. In addition, Congress declared that both research- and commercial-scale development of oil shale and tar sands should (1) be conducted in an environmentally sound manner using management practices that will minimize potential impacts, (2) occur with an emphasis on sustainability, and (3) benefit the United States while taking into account concerns of the affected states and communities. To support this declaration of policy, Congress directed the Secretary of the Interior to undertake a series of steps, several of which are directly related to the development of a commercial leasing program for oil shale and tar sands. One of these steps was the completion of a programmatic environmental impact statement (PEIS) to analyze the impacts of a commercial leasing program for oil shale and tar sands resources on public lands, with an emphasis on the most geologically prospective lands in Colorado, Utah, and Wyoming. For oil shale, the scope of the PEIS analysis includes public lands within the Green River, Washakie, Uinta, and Piceance Creek Basins. For tar sands, the scope includes Special Tar Sand Areas (STSAs) located in Utah. This paleontological resources overview report was prepared in support of the Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and PEIS, and it is intended to be used by Bureau of Land Management (BLM) regional paleontologists and field office staff to support future

  4. Technology unlocks tar sands energy

    Energy Technology Data Exchange (ETDEWEB)

    Law, C

    1967-09-25

    Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

  5. Tar sands showdown : Canada and the new politics of oil in an age of climate change

    International Nuclear Information System (INIS)

    Clarke, T.

    2009-01-01

    This book outlined the social and environmental issues facing the oil sands industry in Canada, including economic sovereignty, energy security, water rights and free trade. The tar sands have become vital to the Canadian economy, as they have the potential to increase Canada's foreign oil output by 4 to 5 times in the next 15 years. The author discussed the ecological and social impact of the Alberta tar sands and the real cost of development to Albertans and Canadians. Tar sands oil production generates more than 3 times the amount of greenhouse gas emissions than conventional oil production. The industry is also becoming a prime example of the abuse of water sources. The author emphasized the need to build an alternative energy future in an age of global warming. The main objective of this book was to help stimulate a nation-wide public debate about the tar sands and the critical issues at stake regarding Canada's energy future and an environmental strategy for more sustainable development. refs., tabs., figs.

  6. Class I cultural resource overview for oil shale and tar sands areas in Colorado, Utah and Wyoming.

    Energy Technology Data Exchange (ETDEWEB)

    O' Rourke, D.; Kullen, D.; Gierek, L.; Wescott, K.; Greby, M.; Anast, G.; Nesta, M.; Walston, L.; Tate, R.; Azzarello, A.; Vinikour, B.; Van Lonkhuyzen, B.; Quinn, J.; Yuen, R.; Environmental Science Division

    2007-11-01

    In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the 'Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005', Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. The Bureau of Land Management (BLM) is developing a Programmatic Environmental Impact Statement (PEIS) to evaluate alternatives for establishing commercial oil shale and tar sands leasing programs in Colorado, Wyoming, and Utah. This PEIS evaluates the potential impacts of alternatives identifying BLM-administered lands as available for application for commercial leasing of oil shale resources within the three states and of tar sands resources within Utah. The scope of the analysis of the PEIS also includes an assessment of the potential effects of future commercial leasing. This Class I cultural resources study is in support of the Draft Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and Programmatic Environmental Impact Statement and is an attempt to synthesize archaeological data covering the most geologically prospective lands for oil shale and tar sands in Colorado, Utah, and Wyoming. This report is based solely on geographic information system (GIS) data held by the Colorado, Utah, and Wyoming State Historic Preservation Offices (SHPOs). The GIS data include the information that the BLM has provided to the SHPOs. The primary purpose of the Class I cultural resources overview is to provide information on the affected environment for the PEIS. Furthermore, this report provides recommendations to support planning decisions and the management of cultural resources that could be impacted by future

  7. Heavy crude and tar sands - the long-term oil reserve

    Energy Technology Data Exchange (ETDEWEB)

    Barnea, J

    1984-10-01

    It appears that heavy crude and tar sands occur in many sedimentary areas, and estimates of known world-wide quantities exceed those known for conventional light crude resources. Although there are not precise figures available, production could be as high as three million barrels per day, with Venezuela, the US, and Canada the largest producers. There are different scales to measure the costs of production because of differences in the quality of various types of heavy crude and tar sands. Economic development of these resources should banish fears of oil scarcity in the foreseeable future. A center for information exchange through international meetings and publications is under development.

  8. A role for nuclear energy in the recovery of oil from the tar sands of Alberta

    International Nuclear Information System (INIS)

    Puttagunta, V.R.; Sochaski, R.O.; Robertson, R.F.S.

    1976-12-01

    Techniques of oil recovery from the tar sands and the energy requirements of this operation are described. Fossil fuels, and CANDU reactors are examined as competitive sources of energy for the tar sands plants. The CANDU-OCR reactor appears to have the necessary flexibility to fit into many of the possible methods of recovering oil from the tar sands. Cost comparisons of fossil and nuclear sources show that, for the supply of process steam, the nuclear source is competitive under the criteria of debt financing or low discount rates on capital, continued escalation, and long plant capital write-off period. (author)

  9. Stuck in the tar sands : how the federal government's proposed climate change strategy lets oil companies off the hook

    International Nuclear Information System (INIS)

    2008-10-01

    The credibility of any federal climate change strategy must be measured against its ability to reduce emissions from the tar sands. However, the federal government has proposed a climate change strategy that would allow tar sands producers to double their total emissions over the next decade. This report discussed how the federal government's proposed climate change strategy lets oil companies off the hook. The report discussed the problems and harmful effects associated with tar sands development, including greenhouse gas emissions; water depletion and pollution; toxic air emissions; destruction of the boreal forest; violation of native rights; threat to energy security; and negative socio-economic spin-off from an overheated economy. The federal government's proposed strategy was also assessed in terms of its weak greenhouse gas targets; ignoring the recent growth in tar sands emissions; adopting intensity-based targets instead of hard caps on greenhouse gas pollution, allowing total emissions from the tar sands to keep climbing; putting off critical measures until 2018; awarding oil companies hundreds of millions of dollars in credits for meeting targets they have already adopted voluntarily; lowballing the price of oil and downplaying future growth in tar sands emissions; ignoring huge portions of the oil industry's greenhouse gas pollution; letting oil companies buy their way out at rockbottom prices instead of forcing them to reduce their own emissions; and subsidizing increased tar sands production. It was concluded that the federal government's proposed plan to reduce greenhouse gas emissions was inadequate, because it failed to crack down on rising greenhouse gas emissions from the tar sands, one of Canada's most carbon intensive and fastest growing industries. 29 refs., 1 appendix

  10. The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

    Energy Technology Data Exchange (ETDEWEB)

    Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-04-01

    Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

  11. Trace metals in heavy crude oils and tar sand bitumens

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, J.G.

    1990-11-28

    Fe, Ni, and V are considered trace impurities in heavy crude oils and tar sand bitumens. In order to understand the importance of these metals, we have examined several properties: (1) bulk metals levels, (2) distribution in separated fractions, (3) size behavior in feeds and during processing, (4) speciation as a function of size, and (5) correlations with rheological properties. Some of the results of these studies show: (1) V and Ni have roughly bimodal size distributions, (2) groupings were seen based on location, size distribution, and Ni/V ratio of the sample, (3) Fe profiles are distinctively different, having a unimodal distribution with a maximum at relatively large molecular size, (4) Fe concentrations in the tar sand bitumens suggest possible fines solubilization in some cases, (5) SARA separated fractions show possible correlations of metals with asphaltene properties suggesting secondary and tertiary structure interactions, and (6) ICP-MS examination for soluble ultra-trace metal impurities show the possibility of unexpected elements such as U, Th, Mo, and others at concentrations in the ppB to ppM range. 39 refs., 13 figs., 5 tabs.

  12. Cashing in on Tar Sands. RBS, UK banks and Canada's 'blood oil'

    Energy Technology Data Exchange (ETDEWEB)

    Evans, M.; Howarth, C.; Kellay, A.; Laboucan, B.J.; Mercredi, M.; Minio-Paluelo, M.; Schling, H.; Smith, K.; Thomas-Muller, C.; Wood, A.

    2010-03-15

    Tar sands extraction in Canada is devastating Indigenous communities, wildlife and vast areas of boreal forests, as well as being many times more carbon-intensive to produce than 'conventional' oil. The higher oil prices in recent years have meant that it's become a more attractive prospect for oil companies to expand their operations in the costly process of obtaining and processing the thick bitumen into a usable form. It's estimated that the industry is looking for a capital investment of 120-220 billion USD over the next 20 years to build the new pipelines, mines, refineries and upgraders that are necessary to sustain the boom. This report looks at the role that UK banks are playing in providing the necessary capital, and how RBS (Royal Bank of Scotland), which is 84% owned by the UK public, has been the bank the most heavily involved in underwriting loans to companies engaging in tar sands extraction.

  13. Solvent extraction of Southern US tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Penney, W.R.

    1990-01-01

    The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

  14. Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

  15. The search for a source rock for the giant Tar Sand triangle accumulation, southeastern Utah

    Science.gov (United States)

    Huntoon, J.E.; Hansley, P.L.; Naeser, N.D.

    1999-01-01

    A large proportion (about 36%) of the world's oil resource is contained in accumulations of heavy oil or tar. In these large deposits of degraded oil, the oil in place represents only a fraction of what was present at the time of accumulation. In many of these deposits, the source of the oil is unknown, and the oil is thought to have migrated over long distances to the reservoirs. The Tar Sand triangle in southeastern Utah contains the largest tar sand accumulation in the United States, with 6.3 billion bbl of heavy oil estimated to be in place. The deposit is thought to have originally contained 13-16 billion bbl prior to the biodegradation, water washing, and erosion that have taken place since the middle - late Tertiary. The source of the oil is unknown. The tar is primarily contained within the Lower Permian White Rim Sandstone, but extends into permeable parts of overlying and underlying beds. Oil is interpreted to have migrated into the White Rim sometime during the Tertiary when the formation was at a depth of approximately 3500 m. This conclusion is based on integration of fluid inclusion analysis, time-temperature reconstruction, and apatite fission-track modeling for the White Rim Sandstone. Homogenization temperatures cluster around 85-90??C for primary fluid inclusions in authigenic, nonferroan dolomite in the White Rim. The fluid inclusions are associated with fluorescent oil-bearing inclusions, indicating that dolomite precipitation was coeval with oil migration. Burial reconstruction suggests that the White Rim Sandstone reached its maximum burial depth from 60 to 24 Ma, and that maximum burial was followed by unroofing from 24 to 0 Ma. Time-temperature modeling indicates that the formation experienced temperatures of 85-90??C from about 35 to 40 Ma during maximum burial. Maximum formation temperatures of about 105-110??C were reached at about 24 Ma, just prior to unroofing. Thermal modeling is used to examine the history of potential source rocks

  16. Research and information needs for management of tar sands development. Interim report Apr-May 83

    Energy Technology Data Exchange (ETDEWEB)

    1983-05-01

    The report discusses important research and information needs for federal lease management of lands with tar sands resources. Short-term needs include more complete definition and characterization of deposits, hydrology, and regions downwind from tar sands areas. Longer-term needs include demonstration-scale operations to resolve production, waste management, and reclamation problems and to provide opportunities for measurement, analysis, and assessment of mining and processing wastes and emissions. Most of the known federal tar sands resource is in eastern Utah and contains about 25 billion barrels of bitumen. Recent legislation provides that existing mining claims and oil and gas leases may be converted to combined hydrocarbon leases including tar sands. Federal approval, which must be applied for by November 1983, is a condition for conversion.

  17. 1170-MW(t) HTGR-PS/C plant application study report: tar sands oil recovery application

    International Nuclear Information System (INIS)

    Rao, R.; McMain, A.T. Jr.

    1981-05-01

    This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to tar sands oil recovery and upgrading. The raw product recovered from the sands is a heavy, sour bitumen; upgrading, which involves coking and hydrodesulfurization, produces a synthetic crude (refinable by current technology) and petroleum coke. Steam and electric power are required for the recovery and upgrading process. Proposed and commercial plants would purchase electric power from local utilities and obtain from boilers fired with coal and with by-product fuels produced by the upgrading. This study shows that an HTGR-PS/C represents a more economical source of steam and electric power

  18. Economic and environmental effects of the FQD on crude oil production from tar sands

    Energy Technology Data Exchange (ETDEWEB)

    Kampman, B.; De Buck, A.; Afman, M. [CE Delft, Delft (Netherlands); Van den Berg, J.; Otten, G.J. [Carbon Matters, Den Haag (Netherlands)

    2013-05-15

    The production of unconventional crudes in Canada and Venezuela and exports of these crudes to the EU are investigated. In addition the potential economic and environmental impact of the proposed EU FQD measures (Fuel Quality Directive) on the production of crudes from tar sands and on new tar sand exploration projects are examined. CE Delft has analysed the impact by using a dedicated cost model. For existing projects, the model determines the effect on the basis of marginal production costs. For planned projects the model used the net present value (NPV) of proposed investments. The impacts were determined for a range of crude oil prices and FQD price effects. Combined, for existing and new projects together, the maximum effect would be at a price level at 60 USD/bbl, with savings of up to 19 Mt CO2/y at an FQD price differential of 3 euro/bbl. This overall effect would be substantial and come on top of the total emission reduction effect of the FQD of 60 Mt CO2/y, which will be achieved mostly by the blending of low-carbon fuels and reduced flaring and venting. As part of the reduction of transport greenhouse gas (GHG) emissions, the revised FQD obliges fuel suppliers to reduce these emissions by 6% by 2020 on a well-to-wheel basis. The EU is currently developing a methodology to differentiate fossil fuels on the basis of feedstock and GHG emissions. In the proposal, diesel produced from tar sands, has been given a default emission value of 108.5 gCO2 eq/MJ, while diesel from conventional crude was set at 89.1 gCO2 eq/MJ. The Commission's proposal is currently undergoing an impact assessment and is expected to be resubmitted to the Council later this year (2013)

  19. Reports on 1974 result of Sunshine Project. Research on tar sand and oil shale; 1974 nendo tar sand oyobi oil shale ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-04-04

    The purpose of this research is to grasp the policy of the oil sand resource countries, the properties and existing conditions of the resources, effects of the oil sand resources on a long term energy supply/demand, etc., and to clarify the meaning and position of the researches on the development of oil sand resources in the future energy policy of Japan. The quantities of oil sand resources are mostly in the process of investigation except Alberta province of Canada and are estimated to be two trillion barrels. The quantity for which strip mining is possible is about 90 billion barrels, which are mostly located in the Athabasca region. The oil sand holding countries take a policy of positively developing oil sand. No barriers are particularly provided against the introduction of foreign technology and capital. Where the prospects are possible for the development of oil sand are Canada and Venezuela. R and D should be emphasized on the refining of bitumen and the extraction method within the oil reservoir. The investment per b/d is about 15-20 thousand dollars, which is likely to be more than twice as much as for the North Sea oilfields. The properties and quality of the synthetic crude oil are superior while the risk of exploitation is small; therefore, oil sand will be competitive with crude oil in the future. (NEDO)

  20. Oil sands to the rescue: oil sand microbial communities can degrade recalcitrant alkyl phenyl alkanoic acids

    Energy Technology Data Exchange (ETDEWEB)

    Whitby, Corinne [University of Essex (Canada)], email: cwhitby@essex.ac.uk

    2011-07-01

    Almost half of all global oil reserves are found as biodegraded heavy oils found in vast tar sand deposits located in North and South America and these account for 47% of Canadian oil production. Oil sand extraction generates large amounts of toxic waste water, known as oil sand process waters (OSPW), that are stored in large tailing ponds that contain toxic compounds like naphthenic acids (NAs). The presence of NAs creates problems like toxicity, corrosion, and the formation of calcium napthenate deposits which block pipelines and other infrastructure and need to be removed. This paper presents oil sand microbial communities that can degrade these NAs. The approach is to apply new aliphatic and aromatic NAs as substrates to supplement and identify NA degrading microbes and also to identify the metabolites produced and explain NA degradation pathways and the functional genes involved. The chemistry and the processes involved are explained. From the results, it is suggested that pure cultures of P. putida KT2440 be used against NAs.

  1. Canada's oil sands: nuclear power in an integrated energy economy

    Energy Technology Data Exchange (ETDEWEB)

    Isaacs, E. [Alberta Energy Research Inst., Calgary, Alberta (Canada)

    2008-07-01

    This paper discusses the role of nuclear power in Canada's oil sands industry. It outlines the oil sands resource in Alberta and the various industrial projects to recover the oil from the tar sands. It points to continuing innovation in technology since the 1930's. The hydrogen required for upgrading bitumen is made from natural gas. Finally, it discusses the next wave of oil sands production technologies.

  2. Pan Am tar sand bid revealed

    Energy Technology Data Exchange (ETDEWEB)

    Gray, E

    1968-12-16

    Muskeg Oil Co., wholly-owned subsidiary of Pan American Canada Oil Co. Ltd., hopes to expand its proposed initial 8,000 bpd in situ Athabasca tar sand production scheme to an ultimate rate of 60,000 bpd. The Muskeg recovery process involves an in situ combustion technique developed by Pan American and applied successfully in experimental work in the Athabasca area. The underground burning process develops heat in the formation, reduces crude bitumen viscosity, and displaces the bitumen to the producing wells. Core analyses have been used to determine bitumen in place, wherever possible. Values for uncored wells were based on logs, through development of an empirical relationship between formation resistivity measured by focused logging devices and bitumen content determined by core analysis. The proposed recovery process is a 10-acre well spacing with 9-spot configuration. The McMurray Formation will be fractured hydraulically and preheated by a combustion process. The bitumen will be recovered by a combustion displacement process utilizing air and water.

  3. Centennial review-forecast--oil sands, shales spar for markets

    Energy Technology Data Exchange (ETDEWEB)

    Pamenter, C B

    1967-09-01

    The relationship between possible developments of tar sands and oil shale deposits to the future of the oil and gas industry is examined. The Athabasca tar sands are estimated to contain 85 billion bbl of synthetic crude oil which can be exploited using currently available mining equipment and proven techniques. Another 240 billion bbl of synthetic crude are potentially available through in-situ extraction methods. Great Canadian Oil Sands Ltd. is using an extraction procedure which involves a surface mining operation, extraction and processing of the bitumen, and product shipments via a 266-mile pipeline. This procedure will be used to produce 45,000 bpd of synthetic crude and 300 ton per day of sulfur. Syncrude Canada Ltd. and Shell Canada Ltd. both have applied to the Alberta government for permission to operate 100,000-bpd operations. Syncrudes is a mining operation and Shell plans to use in-situ extraction. A number of companies have conducted research projects concerning shale oil recovery. The majority of these projects have been aimed at improving mining operations. In-situ retorting of kerogen and extraction of oil has also received consideration.

  4. Creating fluid injectivity in tar sands formations

    Science.gov (United States)

    Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

    2010-06-08

    Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

  5. Revegetation and management of tailings sand slopes from tar sand extraction: 1978 results

    Energy Technology Data Exchange (ETDEWEB)

    Rowell, M J

    1979-01-01

    The results are reported of research into the revegetation of two areas on a steeply sloping dike composed of tailings sand from tar sand extraction at the Great Canadian Oil Sand Limited plant at Fort McMurray, Alberta. One area was seeded with three pasture grasses and two legumes in 1971 after the slope surface had been mixed with peat to a depth of 15 cm. A second area had been amended with peat or peat and overburden and differing rates of fertilizer added. A mix containing nine grasses, four legumes, and oats, as a companion crop, was seeded in July 1976. The objectives of the research were to study methods for the establishment of a stable vegetative cover that would prevent erosion of the slope and, in time, might become a self maintaining unit. Tillage of soil amendments to a depth of 15 cm and 30 cm were compared in promoting deeper rooting and stabilizing of the slope.

  6. The extraction of bitumen from western oil sands

    International Nuclear Information System (INIS)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-08-01

    The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report

  7. A Critical Review of the Oil and Tar Sands of the Dahomey Basin

    International Nuclear Information System (INIS)

    Osundina, A.; Mustapha, A.; Nzewi, T.

    2002-01-01

    The Benin Basin previously referred to as the Dahomey embayment has been designated as a frontier basin within Nigeria due to its potentially high prospects, but comparatively low exploitation campaign to date. The basin offers a promising opportunity for heavy oil exploration in a narrow belt extending westward from Edo State to the republic of Benin; while offshore, there are high prospects for finding more conventional hydrocarbon.The eastern Dahomey embayment is known to have an extensive reserve of hydrocarbons (bitumen and tar sands). The sediments occur in a 5 8 km belt stretching 120km from the fringes of Lagos State through Ogun, Ondo and Edo States. The estimated reserve potentials exceed 30 billion barrels of oil equivalent.Recently acquired seismic data in OPL 309 and 310, and subsequent drilling of 2 wells on the narrow continental shelf, have shown the presence of closed structures over Basement Highs and other related structural styles in the basin and confirm that conventional light oils and condensates hydrocarbons occur in commercial quantity. These hydrocarbons are reservoired in stratigraphic sequences of Albian Cenomanian age.This paper hopes to expose the hidden riches of this Basin and hopefully get the attention of the big players in refocusing their interests in the basin that attracted attention of the early petroleum explorers to Nigeria approximately 100 years ago

  8. Coal tar phototherapy for psoriasis reevaluated: erythemogenic versus suberythemogenic ultraviolet with a tar extract in oil and crude coal tar

    International Nuclear Information System (INIS)

    Lowe, N.J.; Wortzman, M.S.; Breeding, J.; Koudsi, H.; Taylor, L.

    1983-01-01

    Recent studies have questioned the therapeutic value of coal tar versus ultraviolet (UV) radiation and their relative necessity in phototherapy for psoriasis. In this investigation, different aspects of tar phototherapy have been studied in single-blind bilateral paired comparison studies. The effects of 1% crude coal tar were compared with those of petrolatum in conjunction with erythemogenic and suberythemogenic doses of ultraviolet light (UVB) using a FS72 sunlamp tubed cabinet. Crude coal tar was clinically superior to petrolatum with suberythemogenic ultraviolet. With the erythemogenic UVB, petrolatum was equal in efficacy to crude coal tar. Suberythemogenic UVB was also used adjunctively to compare the effects of a 5% concentration of a tar extract in an oil base to 5% crude coal tar in petrolatum or the oil base without tar. The tar extract in oil plus suberythemogenic UVB produced significantly more rapid improvement than the oil base plus UVB. The direct bilateral comparison of equal concentrations of tar extract in oil base versus crude coal tar in petrolatum in a suberythemogenic UV photo regimen revealed no statistical differences between treatments. In a study comparing tar extract in oil and the oil base without ultraviolet radiation, the tar extract in oil side responded more rapidly

  9. Analysis of the environmental control technology for tar sand development

    Energy Technology Data Exchange (ETDEWEB)

    de Nevers, N.; Glenne, B.; Bryner, C.

    1979-06-01

    The environmental technology for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the waste tar sand were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. Currently there are two large-scale plants producing liquid fuels from tar sands in Alberta, Canada which use similar technology involving surface mining, hot water extraction, and surface disposal of waste sand. These projects all meet the Canadian environmental control regulations in force at the time they began. The largest US deposits of tar sands are much smaller than the Canadian; 95 percent are located in the state of Utah. Their economics do not appear as attractive as the Canadian deposits. The environmental control costs are not large enough to make an otherwise economic project uneconomic. The most serious environmental conflict likely to occur over the recovery of liquid fuels from the US deposits of tar sands is that caused by the proximity of the deposits to national parks, national monuments, and a national recreation area in Utah. These areas have very stringent air pollution requirements; and even if the air pollution control requirements can be met, there may still be adequate opposition to large-scale mining ventures in these areas to prevent their commercial exploitation. Another environmental constraint may be water rights availability.Essentially all of the water running in the Colorado river basin is now legally allocated. Barring new interpretations of the legality of water rights purchase, Utah tar sands developments should be able to obtain water by purchasing existing irrigation water rights.

  10. Bioremediation potential of coal-tar-oil-contaminated soil

    International Nuclear Information System (INIS)

    Lajoie, C.A.

    1991-01-01

    The bioremediation of coal tar oil contaminated soil was investigated in 90 day laboratory simulation experiments. The effect of soil moisture, humic acid amendment, and coal tar oil concentration on the rate of disappearance of individual coal tar oil constituents (PAHs and related compounds) was determined by methylene chloride extraction and gas chromatography. Mass balance experiments determined the fate of both the individual 14 C-labeled PAHs phenanthrene, pyrene, and benzo(a)pyrene, and the total coal tar oil carbon. Mineralization, volatilization, incorporation into microbial biomass, disappearance of individual coal tar oil constitutents, and the distribution of residual 14 C-activity in different soil fractions were measured. The rate of disappearance of coal tar oil constituents increased with increasing soil moisture over the experimental range. Humic acid amendment initially enhanced the rate of disappearance, but decreased the extent of disappearance. The amount of contamination removed decreased at higher coal tar oil concentrations. The practical limit for biodegradation in the system tested appeared to be between 1.0 and 2.5% coal tar oil. Mineralization accounted for 40 to 50% of the applied coal tar oil. Volatilization was a minor pathway of disappearance

  11. Creating and maintaining a gas cap in tar sands formations

    Science.gov (United States)

    Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

    2010-03-16

    Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

  12. Separating cresote from tars, mineral oils, etc

    Energy Technology Data Exchange (ETDEWEB)

    Erdmann, E

    1921-01-07

    Phenolic bodies are extracted from tars such as lignite, shale, peat, coal, producer and low temperature tars, and from tar distillates and residues and from mineral oils and distillates by washing with a mixture of acetone and water. Acetone extracts of the tars etc., may be mixed with water or aqueous acetone to cause the separation of the oils, while the creosote remains in solution.

  13. Athabasca tar sand reservoir properties derived from cores and logs

    International Nuclear Information System (INIS)

    Woodhouse, R.

    1976-01-01

    Log interpretation parameters for the Athabasca Tar Sand Lease No. 24 have been determined by careful correlation with Dean and Stark core analysis data. Significant expansion of Athabasca cores occurs as overburden pressure is removed. In the more shaly sands the core analysis procedures remove adsorbed water from the clays leading to further overestimation of porosity and free water volume. Log interpretation parameters (R/sub w/ = 0.5 ohm . m and m = n = 1.5) were defined by correlation with the weight of tar as a fraction of the weight of rock solids (grain or dry weight fraction of tar). This quantity is independent of the water content of the cores, whereas porosity and the weight of tar as a fraction of the bulk weight of fluids plus solids (bulk weight fraction) are both dependent on water content. Charts are provided for the conversion of bulk weight fraction of fluids to porosity; grain weight fraction of fluids to porosity; log derived porosity and core grain weight tar to water saturation. Example results show that the core analysis grain weight fraction of tar is adequately matched by the log analyses. The log results provide a better representation of the reservoir fluid volumes than the core analysis data

  14. Gasification of oil sand coke: review

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E. [IMAF Group, Ottawa, ON (Canada)

    1998-08-01

    The production of synthetic crude from the tar sands in Western Canada has been steadily increasing. Most of the delayed coke produced by Suncor is combusted on site, whereas all fluid coke produced by Syncrude is stockpiled.The database on the chemical and physical properties of the oil sand coke, including the composition and fusion properties of the mineral matter, has been established. The reactivity of the coke was determined by oxygen chemisorption, fixed bed and fluid bed bench scale gasification and pilot plant gasification. The reactivity of the oil sand coke for gasification is rather low and comparable to high rank coals, such as anthracite. Slurrability tests revealed that a solid concentration in water, approaching 70 wt%, can be achieved. Gasification is the front runner among clean technologies for the conversion of carbonaceous solids to useful products. Several commercial gasifiers are available to cover the wide range of severity. Because of the low reactivity of oil sands coke, high severity conditions are required to achieve high gasification conversion. Such conditions can be attained in entrained bed gasifiers. Gasifiers employing both dry and slurry feeding systems are suitable. A high efficiency, low SO{sub x} and NO{sub x} emissions, as well as a low solid waste production are among the key advantages of the gasification technology compared with thecompeting technologies. Commercial gasification of oil sands coke is delayed because of the availability of natural gas on the site of the upgrading plants. Potential for the transportation of the oil sand coke to USA for electricity generation using the integrated gasification combined-cycle (IGCC) technology was evaluated. 27 refs., 17 figs., 9 tabs.

  15. Study on tar generated from downdraft gasification of oil palm fronds.

    Science.gov (United States)

    Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

    2014-01-01

    One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

  16. Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

    Directory of Open Access Journals (Sweden)

    Samson Mekbib Atnaw

    2014-01-01

    Full Text Available One of the most challenging issues concerning the gasification of oil palm fronds (OPF is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3 in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

  17. Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

    Science.gov (United States)

    Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

    2014-01-01

    One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study. PMID:24526899

  18. Environmental survey - tar sands in situ processing research program (Vernal, Uintah County, Utah). [Reverse-forward combustion; steam injection

    Energy Technology Data Exchange (ETDEWEB)

    Skinner, Q.

    1980-03-01

    Research will be done on the reverse-forward combustion and steam injection for the in-situ recovery of oil from tar sands. This environmental survey will serve as a guideline for the consideration of environmental consequences of such research. It covers the construction phase, operational phase, description of the environment, potential impacts and mitigations, coordination, and alternatives. (DLC)

  19. Mineral oils, tars. [British patent

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, A M; Handmarch, E

    1933-08-11

    Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

  20. Process and apparatus for recovering of oil, bitumen, tar, resins, etc

    Energy Technology Data Exchange (ETDEWEB)

    1921-11-06

    A process for recovering oil, bitumen, tar, and resins from oil shale, oil sands, Fuller's earth, peat, brown coal, mineral coal, and wood, through direct action of superheated steam on the material, is characterized by the fact that superheated steam with or without mixing of inert gases at a temperature, which lies below the decomposition temperature of the material being treated, is passed through the material with a high velocity. It leaves through nozzles, used in steam turbines. A method of carrying out the process in which solution medium is used for action on the material is characterized by the fact that solvents such as benzine and benzol are mixed with steam in different quantities.

  1. Summary of research and information needs for the management of selected onshore energy minerals: oil shale, tar sands, arctic oil and gas, and uranium. Final report 1982-83

    Energy Technology Data Exchange (ETDEWEB)

    1983-11-01

    The report assesses research needs for the management, regulation, reclamation, and conservation of oil shale, tar sands, arctic oil and gas, and uranium deposits currently under federal jurisdiction and concludes that additional research is required to achieve the goals of good management, including conservation, protection of life and property, and minimization of environmental degradation. The report recommends (1) establishment of a standing advisory scientific and engineering committee on onshore minerals management research to influence future research directions and implementation; (2) development of a comprehensive library and data center for research results; and (3) encouragement of the operation of demonstration-scale production facilities where they are lacking. More detailed summaries of current knowledge and perceived research needs are to be found in the four interim reports of the committee.

  2. The extraction of bitumen from western oil sands. Annual report, July 1991--July 1992

    Energy Technology Data Exchange (ETDEWEB)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-08-01

    The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report.

  3. In situ heat treatment of a tar sands formation after drive process treatment

    Science.gov (United States)

    Vinegar, Harold J.; Stanecki, John

    2010-09-21

    A method for treating a tar sands formation includes providing a drive fluid to a hydrocarbon containing layer of the tar sands formation to mobilize at least some hydrocarbons in the layer. At least some first hydrocarbons from the layer are produced. Heat is provided to the layer from one or more heaters located in the formation. At least some second hydrocarbons are produced from the layer of the formation. The second hydrocarbons include at least some hydrocarbons that are upgraded compared to the first hydrocarbons produced by using the drive fluid.

  4. Sunflower oil in the treatment of hot tar burns.

    Science.gov (United States)

    Türegün, M; Oztürk, S; Selmanpakoğlu, N

    1997-08-01

    Hot tar burns compose a unique class of thermal injury, because removal of this highly sticky compound may be very difficult without inflicting additional tissue damage. Early removal of tar facilitates assessment of the burn and improves patient comfort. Although the use of many substances for the painless removal of tar has been described, we used sunflower oil effectively in the treatment of four tar burn patients. This first report describes the practical and successful use of sunflower oil which was easily obtained from the hospital kitchen.

  5. Retorting of bituminous sands

    Energy Technology Data Exchange (ETDEWEB)

    Chaney, P E; Ince, R W; Mason, C M

    1872-09-26

    This method of recovering oil from mined tar sands involves forming compacted tar sands pieces by special conditioning treatment that provides low internal permeability. The compacted pieces are then retorted in fixed bed form. The conditioning treatment can involve rolling of preformed pellets, compaction in a mold or pressure extrusion. Substantial collapsing of the bed during retorting is avoided. (9 claims) (Abstract only - original article not available from T.U.)

  6. Sedimentological and Scanning Electron Miscroscopic Descriptions of Afowo Oil Sand Deposits, South Western Nigeria

    Directory of Open Access Journals (Sweden)

    Akinmosin A

    2017-12-01

    Full Text Available Sedimentological and scanning electron microscopic analyses of some shallow reservoir tar sand samples in parts of Southwestern Nigeria were carried out with the aim of characterizing the reservoir properties in relation to bitumen saturation and recovery efficiency. The production of impregnated tar from the sands requires the reservoir to be of good quality. A total of thirty samples were collected at different localities within the tar sand belt (ten out of these samples were selected for various reservoir quality analyses based on their textural homogeneity. The result of particle size distribution study showed that bulk of the sands is medium – coarse grained and moderately sorted. The grain morphologies are of low to high sphericity with shapes generally sub-angular to sub-rounded, implying that the sands have undergone a fairly long transportation history with depositional energy having a moderate to high velocity. The quartz content was made up of about 96% of the total mineralogical components; the sediments of the Afowo Formation can be described to be mineralogically and texturally stable. The result of the scanning electron microscopy (SEM analysis revealed that the oil sands contained minerals which had been precipitated and occurred as pore filling cement; these minerals include sheet kaolinite, block kaolinite, vermiform kaolinite, pyrite crystals and quartz. The SEM images also showed micro-pores ranging from 0.057µm to 0.446µm and fractures. The study showed that the clay minerals contained in the Afowo reservoir rocks were mainly kaolinite. Kaoline unlike some other clays (e.g Montimorillonite does not swell with water, hence it is not expected to have any negative effects on the reservoir quality, especially during enhanced oil recovery operations.

  7. Recovery of very viscous lubricating oils from shale-tar, etc

    Energy Technology Data Exchange (ETDEWEB)

    Erdmann, E

    1918-01-22

    A process is disclosed for the recovery of very viscous lubricating oils from brown-coal tar and shale tar, consisting in driving off from the crude tar or the tar freed from volatile constituents after removal of paraffin by precipitation with a volatile solvent such as acetone or one of its homologs, the light oils more or less completely with superheated steam from about 200 to 250/sup 0/C without any outside heating over a free flame.

  8. Geology and resources of the Tar Sand Triangle, southeastern Utah

    Energy Technology Data Exchange (ETDEWEB)

    Dana, G.F.; Oliver, R.L.; Elliott, J.R.

    1984-05-01

    The Tar Sand Triangle is located in southeastern Utah between the Dirty Devil and Colorado Rivers and covers an area of about 200 square miles. The geology of the area consists of gently northwest dipping strata exposed in the box canyons and slopes of the canyonlands morphology. Strata in the area range in age from Jurassic to Permian. The majority of tar sand saturation is found in the Permian White Rim Sandstone Member of the Cutler Formation. The White Rim Sandstone Member consists of a clean, well-sorted sandstone which was deposited in a shallow marine environment. Resources were calculated from analytical data from the three coreholes drilled by the Laramie Energy Technology Center and other available data. The total in-place resources, determined from this study, are 6.3 billion barels. Previous estimates ranged from 2.9 to 16 million barrels. More coring and analyses will be necessary before a more accurate determination of resources can be attempted. 8 references, 11 figures, 7 tables.

  9. Heating tar sands formations to visbreaking temperatures

    Science.gov (United States)

    Karanikas, John Michael [Houston, TX; Colmenares, Tulio Rafael [Houston, TX; Zhang, Etuan [Houston, TX; Marino, Marian [Houston, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Beer, Gary Lee [Houston, TX; Dombrowski, Robert James [Houston, TX; Jaiswal, Namit [Houston, TX

    2009-12-22

    Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat may be controlled so that at least a majority of the section reaches an average temperature of between 200.degree. C. and 240.degree. C., which results in visbreaking of at least some hydrocarbons in the section. At least some visbroken hydrocarbon fluids may be produced from the formation.

  10. Low-temperature tar and oil: properties and applications

    Energy Technology Data Exchange (ETDEWEB)

    Heinze, R

    1942-01-01

    In Germany the value of low-temperature tar is largely dependent on its fuel fractions; these vary with the coal and the method of carbonization (external heating or recirculated gases). Brown-coal tars can be processed by distillation, cracking under pressure, hydrogenation under pressure (largest volume of tar is processed by this method) and by solvent extraction, with EtOH, SO/sub 2/, or phenol. Each of these processes is discussed in detail. In the pressure-hydrogenation process, 1.25 kilogram of brown-coal tar yields approximately 1 kilogram of gasoline with an octane number of 60 to 70. Low-temperature tars from bituminous coals can be hydrogenated readily but are not well adapted to solvent extraction. Attempts should be made to produce tar approximating the desired characteristics for fuel directly from the carbonizing apparatus. For laboratory carbonization tests, an approximation to results secured by externally heated retorts is secured by using an insert consisting of a series of perforated trays in the 200-gram Fischer aluminum retort; this reduces the capacity to 100 gram. Fractional condensation is used to separate heavy oil, middle oil, and liquor; low-boiling products are condensed at -20/sup 0/ by solid CO/sub 2/.

  11. Heating tar sands formations while controlling pressure

    Science.gov (United States)

    Stegemeier, George Leo [Houston, TX; Beer, Gary Lee [Houston, TX; Zhang, Etuan [Houston, TX

    2010-01-12

    Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. A pressure in the majority of the section may be maintained below a fracture pressure of the formation. The pressure in the majority of the section may be reduced to a selected pressure after the average temperature reaches a temperature that is above 240.degree. C. and is at or below pyrolysis temperatures of hydrocarbons in the section. At least some hydrocarbon fluids may be produced from the formation.

  12. A cost comparison of nuclear and fossil power for the Alberta tar sands

    International Nuclear Information System (INIS)

    Sochaski, R.O.; Smith, D.W.

    1977-04-01

    One technique envisaged for commercial development of the Alberta tar sands is in-situ removal of bitumen by injection of steam into the formation at high temperature and pressure. The 3000 MW of thermal power required for a typical 20 Gg/d plant could be supplied by a nuclear reactor. Accordingly, an economic comparison was made between a CANDU organic-cooled reactor and a conventional coal-fired station, using a variety of financial ground rules. This analysis shows that for debt-financed cases, nuclear power has essentially no economic competition from coal. For equity cases, the competitive position of a coal-fired station is heavily dependent on the cost of coal delivered to the tar sands area, discount rate, amortization period and inflation rate. (author)

  13. The extraction of bitumen from western oil sands. Final report, July 1989--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Fletcher, J.V.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1994-03-01

    Research and development of surface extraction and upgrading processes of western tar sands are described. Research areas included modified hot water, fluidized bed, and rotary kiln pyrolysis of tar sands for extraction of bitumen. Bitumen upgrading included solvent extraction of bitumen, and catalytic hydrotreating of bitumen. Characterization of Utah tar sand deposits is also included.

  14. Process for removing heavy metal compounds from heavy crude oil

    Science.gov (United States)

    Cha, Chang Y.; Boysen, John E.; Branthaver, Jan F.

    1991-01-01

    A process is provided for removing heavy metal compounds from heavy crude oil by mixing the heavy crude oil with tar sand; preheating the mixture to a temperature of about 650.degree. F.; heating said mixture to up to 800.degree. F.; and separating tar sand from the light oils formed during said heating. The heavy metals removed from the heavy oils can be recovered from the spent sand for other uses.

  15. The Alberta oil sands story

    Energy Technology Data Exchange (ETDEWEB)

    1974-01-01

    This report serves as a detailed introduction to the Alberta oil sands and their development. It includes a description of the oil sands deposits, an outline of crude bitumen recovery and upgrading processes, the role of Alberta Energy Company in oil sands development, environmental aspects, manpower requirements for oil sands development, research needs, and further oil sands projects. Presently proven recoverable reserves in the oil sands amount to 26.5 billion bbl of synthetic crude. Production from the Syncrude plant (125,000 bbl/d capacity) is expected to begin in 1977, followed by a Shell Canada operation around 1980. The provincial government will participate in the oil sand industry through its joint venture participation in Syncrude and its 50% share in Alberta Energy Company; the latter company participates in related aspects of the Syncrude project, such as pipelines. The result of Alberta's participation in the industry will mean that, directly or indirectly, the province will realize 60% of the total profits. The job creation potential of oil sands projects is estimated to be extensive, with a direct and indirect work force supported by oil sands activities possibly reaching 180,000 persons by the year 2000. Research needs have been identified, particularly in the area of in-situ thermal recovery technology, and the creation of the Alberta Oil Sands Technology and Research Authority has been authorized in order to meet these needs. Although current reserves are sufficient to support 20-30 synthetic crude plants, a number of factors will limit expansion of the industry. 8 figs., 5 tabs.

  16. Heat-resistant agent used for control sand of steam huff and puff heavy oil well

    Science.gov (United States)

    Zhang, F. S.; Liu, G. L.; Lu, Y. J.; Xiong, X. C.; Ma, J. H.; Su, H. M.

    2018-01-01

    Heat-resistant agent containing hydroxymethyl group was synthesized from coal tar, which has similar structure with phenolic resin and could improve the heat resistance of phenolic resin sand control agent. The results showed that the heat resistance of the sand control agent was improved by adding 10% to 30% heat-resistant agent, after 280°C high temperature treatment for 7d, the compressive strength of consolidated core was increased to more than 5MPa. The compressive strength of consolidation core was not decreased after immersion in formation water, crude oil, acid or alkaline medium, which showed good resistance to medium immersion. The sand control agent had small core damage and the core permeability damage ratio of sand control agent consolidation was only 18.7%.

  17. The documentation of tar balls on oiled shorelines : lessons from the New Carissa, Oregon

    International Nuclear Information System (INIS)

    Owens, E.H.; Zimlicki-Owens, L.M.; Lamarche, A.; Reimer, P.D.; Martin, C.A.

    2000-01-01

    The New Carissa, carrying approximately 400,000 gallons of fuel oils ran aground on the outer shore of North Spit, in the vicinity of Coos Bay, Oregon, on February 4, 1999. The oil was released directly into the nearshore surf zone. Following the spill, a stretch of approximately 300 km of the coast of Oregon was surveyed and monitored. The need for the documentation of stranded tar balls in the neighbourhood of the spill site prompted the implementation of a long-term observation program. Initially, Shoreline Clean-up and Assessment Technique (SCAT) reporting procedures were required. Heavy oiling was followed by stranded oil taking the form of tar balls. The amount of oil on the shoreline decreased and the SCAT procedures alone were no longer adequate. They provided estimations of oil quantities that were too high and failed to provide any discrimination between amounts of oil observed on the beaches. A new reporting technique called Beach Assessment Reporting was designed to overcome the difficulties and record adequately the character and frequency of stranded tar balls. Maps, tables and histograms of stranded tar ball volumes and concentrations were discussed. Since the data spanned nine orders of magnitude at times, the semi-logarithmic scale time series plots of the concentration of the tar balls was used in order to identify trends. Conventional histograms only identified large values and camouflaged smaller trends in the time series. A direct method for describing tar ball concentrations geographically proved to be the use of weekly maximum tar ball concentration maps by segment. 10 refs., 2 tabs., 9 figs

  18. Potential impacts to perennial springs from tar sand mining, processing, and disposal on the Tavaputs Plateau, Utah, USA

    International Nuclear Information System (INIS)

    Johnson, William P.; Frederick, Logan E.; Millington, Mallory R.; Vala, David; Reese, Barbara K.; Freedman, Dina R.; Stenten, Christina J.; Trauscht, Jacob S.; Tingey, Christopher E.; Kip Solomon, D.; Fernandez, Diego P.; Bowen, Gabriel J.

    2015-01-01

    Similar to fracking, the development of tar sand mining in the U.S. has moved faster than understanding of potential water quality impacts. Potential water quality impacts of tar sand mining, processing, and disposal to springs in canyons incised approximately 200 m into the Tavaputs Plateau, at the Uinta Basin southern rim, Utah, USA, were evaluated by hydrogeochemical sampling to determine potential sources of recharge, and chemical thermodynamic estimations to determine potential changes in transfer of bitumen compounds to water. Because the ridgetops in an area of the Tavaputs Plateau named PR Spring are starting to be developed for their tar sand resource, there is concern for potential hydrologic connection between these ridgetops and perennial springs in adjacent canyons on which depend ranching families, livestock, wildlife and recreationalists. Samples were collected from perennial springs to examine possible progression with elevation of parameters such as temperature, specific conductance, pH, dissolved oxygen, isotopic tracers of phase change, water-rock interaction, and age since recharge. The groundwater age dates indicate that the springs are recharged locally. The progression of hydrogeochemical parameters with elevation, in combination with the relatively short groundwater residence times, indicate that the recharge zone for these springs includes the surrounding ridges, and thereby suggests a hydrologic connection between the mining, processing, disposal area and the springs. Estimations based on chemical thermodynamic approaches indicate that bitumen compounds will have greatly enhanced solubility in water that comes into contact with the residual bitumen–solvent mixture in disposed tailings relative to water that currently comes into contact with natural tar. - Highlights: • The potential water quality impacts of the first US tar sand development are considered. • Analyses of perennial springs in adjacent canyons indicate hydrologic

  19. Potential impacts to perennial springs from tar sand mining, processing, and disposal on the Tavaputs Plateau, Utah, USA

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, William P.; Frederick, Logan E.; Millington, Mallory R. [University of Utah, Department of Geology & Geophysics, Salt lake City, UT 84112 (United States); Vala, David [Murray High School, Murray, UT 84107 (United States); Reese, Barbara K. [Butler Middle School, Cottonwood Heights, UT 84121 (United States); Freedman, Dina R. [Hillside Middle School, Salt Lake City, UT 84108 (United States); Stenten, Christina J. [Draper Park Middle School, Draper, UT 84020 (United States); Trauscht, Jacob S.; Tingey, Christopher E.; Kip Solomon, D.; Fernandez, Diego P.; Bowen, Gabriel J. [University of Utah, Department of Geology & Geophysics, Salt lake City, UT 84112 (United States)

    2015-11-01

    Similar to fracking, the development of tar sand mining in the U.S. has moved faster than understanding of potential water quality impacts. Potential water quality impacts of tar sand mining, processing, and disposal to springs in canyons incised approximately 200 m into the Tavaputs Plateau, at the Uinta Basin southern rim, Utah, USA, were evaluated by hydrogeochemical sampling to determine potential sources of recharge, and chemical thermodynamic estimations to determine potential changes in transfer of bitumen compounds to water. Because the ridgetops in an area of the Tavaputs Plateau named PR Spring are starting to be developed for their tar sand resource, there is concern for potential hydrologic connection between these ridgetops and perennial springs in adjacent canyons on which depend ranching families, livestock, wildlife and recreationalists. Samples were collected from perennial springs to examine possible progression with elevation of parameters such as temperature, specific conductance, pH, dissolved oxygen, isotopic tracers of phase change, water-rock interaction, and age since recharge. The groundwater age dates indicate that the springs are recharged locally. The progression of hydrogeochemical parameters with elevation, in combination with the relatively short groundwater residence times, indicate that the recharge zone for these springs includes the surrounding ridges, and thereby suggests a hydrologic connection between the mining, processing, disposal area and the springs. Estimations based on chemical thermodynamic approaches indicate that bitumen compounds will have greatly enhanced solubility in water that comes into contact with the residual bitumen–solvent mixture in disposed tailings relative to water that currently comes into contact with natural tar. - Highlights: • The potential water quality impacts of the first US tar sand development are considered. • Analyses of perennial springs in adjacent canyons indicate hydrologic

  20. Oil sands tax expenditures

    International Nuclear Information System (INIS)

    Ketchum, K; Lavigne, R.; Plummer, R.

    2001-01-01

    The oil sands are a strategic Canadian resource for which federal and provincial governments provide financial incentives to develop and exploit. This report describes the Oil Sands Tax Expenditure Model (OSTEM) developed to estimate the size of the federal income tax expenditure attributed to the oil sands industry. Tax expenditures are tax concessions which are used as alternatives to direct government spending for achieving government policy objectives. The OSTEM was developed within the business Income Tax Division of Canada's Department of Finance. Data inputs for the model were obtained from oil sands developers and Natural Resources Canada. OSTEM calculates annual revenues, royalties and federal taxes at project levels using project-level projections of capital investment, operating expenses and production. OSTEM calculates tax expenditures by comparing taxes paid under different tax regimes. The model also estimates the foregone revenue as a percentage of capital investment. Total tax expenditures associated with investment in the oil sands are projected to total $820 million for the period from 1986 to 2030, representing 4.6 per cent of the total investment. 10 refs., 2 tabs., 7 figs

  1. Recovery of very viscous lubricating oils from shale-tar, etc

    Energy Technology Data Exchange (ETDEWEB)

    Erdmann, E

    1919-09-10

    Modification of the process covered by German Patent 335,190 for recovering very viscous lubricating oils, consisting, in place of brown-coal tar, deparafinned peat tar being subjected to the treatment with superheated steam from about 200 to 250/sup 0/C or to heating in vacuum at a temperature below 250/sup 0/C.

  2. Japan's involvement in oil sands development

    International Nuclear Information System (INIS)

    Sugiura, T.

    1994-01-01

    According to Japanese national policy, exploration and development by Japanese companies in overseas countries are promoted in order to ensure stable oil supplies. Japan Canada Oil Sands Limited (JACOS), part of the JAPEX group, was established during the 1978 world oil crisis to explore and develop Canadian oil sand resources in accordance with Japan's national policy. The JAPEX group, including JACOS, has invested $123 million in oil sands projects in Alberta. JAPEX's first involvement in oil sands was in the Primrose Project operated by Norcen in the Cold Lake area. Five years of cyclic steam stimulation pilot tests did not produce sufficiently good results to justify further operation. The second involvement was the PCEJ Project, a joint effort by four companies that are participating in a bitumen recovery test project in the Athabasca Deposit. JACOS holds 2,452 km 2 of oil sands leases in Alberta. Tests conducted since 1978 in the PCEJ Project include multiwell steam injection pilot tests, some of which showed promise. JACOS is also participating in steam assisted gravity drainage projects and in federal/provincial research programs. Obstacles identified in developing Alberta oil sands are the lack of a bitumen pipeline to Edmonton and the insufficient length of oil sands leases (currently 10 years), given the difficulties of oil sand development. 10 figs

  3. New method for the exact determination of phenols in low-temperature tar and tar oils

    Energy Technology Data Exchange (ETDEWEB)

    Lambris, G; Haferkorn, H

    1949-01-01

    A 3-gram sample of water-free tar or tar oil containing approximately 50% phenols is dissolved in a mixture of benzene and xylene and a known excess of a 20% KOH solution of known normality saturated with benzene and xylene is added. Weight of the KOH is determined by difference. This mixture is shaken repeatedly in a 300-milliliter separatory funnel. After standing for 0.5 h, the dark or almost black phenolate solution containing the major portion is separated and weighed. Care must be taken to prevent the induction of solids. The phenolate in the residue is extracted with hot water and titrated with 0.2N HCl and 1 ml. Congo red (1:100). If water is present in the tar or tar oil, 100 ml of xylene is added immediately after weighing and the water separated by distillation the weight of which must be determined. Any phenols carried over are dissolved in the small quantity of xylene in the distillate. This quantity is added to the bulk of the xylene. After any remaining phenols are extracted from the tar residue with boiling benzene, the benzene-xylene mixture is treated with KOH as above. The accuracy of the method is estimated to be +-1% as shown by experiments with phenol; o-, m-, and p-cresol; cresol mixture; and pyrocatechol. The weight of the dissolved phenols X is determined by X = c - a + cd/(ab - d) where a = weight of KOH, b = HCl used per gram of KOH, C = weight of major portion of phenolate solution, which is formed by shaking the phenol solution with KOH, d = HCl used for titration of phenolate residue.

  4. Process of treating tars

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, C; Hempel, H; Weissenburger, H

    1955-05-05

    A process is described for treating tars or tar oils, especially carbonization tars, characterized in that the tars or tar oils are mixed with benzene or light oils which contain no aromatic material or only slight amounts, or with gas oil in such amounts that the asphalt precipitates, and after separation of the precipitated material the mixture is treated with caustic solution for separation of the phenols, and after separation of the phenolate liquor the mixture is subjected to heating for removal of the dilution medium, then the remaining oil can be used as heating oil or it is submitted to distillation for the purpose of recovering a fuel suitable for diesel motors, while the phenolate liquor is worked up into phenols.

  5. Shaft-retort for treating waste materials, like washery waste, bituminous shale, oil-bearing sands and the like

    Energy Technology Data Exchange (ETDEWEB)

    Koppers, H

    1916-10-29

    A shaft-retort for converting waste materials, like washery waste, bituminous shale, oil-bearing sands, brown coal and non-coking mineral coal to oil and tar by supplying heat through the shaft wall formed of an iron-sheet to the material, which is forced through a feeding member perforated for the removal of gases and vapors, and moved downward in a thin layer on the shaft wall; that is characterized by the fact that the iron heating sheet is made rotatable for the purpose of equalizing overheating of itself and the material to be treated.

  6. Policy Analysis of the Canadian Oil Sands Experience

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2013-09-01

    For those who support U.S. oil sands development, the Canadian oil sands industry is often identified as a model the U.S. might emulate, yielding financial and energy security benefits. For opponents of domestic oil sands development, the Canadian oil sands experience illustrates the risks that opponents of development believe should deter domestic policymakers from incenting U.S. oil sands development. This report does not seek to evaluate the particular underpinnings of either side of this policy argument, but rather attempts to delve into the question of whether the Canadian experience has relevance as a foundational model for U.S. oil sands development. More specifically, this report seeks to assess whether and how the Canadian oil sands experience might be predictive or instructive in the context of fashioning a framework for a U.S. oil sands industry. In evaluating the implications of these underpinnings for a prospective U.S. oil sands industry, this report concentrates on prospective development of the oil sands deposits found in Utah.

  7. Oil sands supply outlook

    International Nuclear Information System (INIS)

    Dunbar, R.

    2004-01-01

    In March 2004, The Canadian Energy Research Institute released a report on the expected future supply from Alberta's oil sands. The report indicates that the future for the already well-established oil sands industry is promising, particularly given the outlook for oil prices. The challenges facing the industry include higher industry supply costs and the need for innovative commercial and technological solutions to address the risks of irregularities and changes in crude oil prices. In 2003, the industry produced 874 thousand barrels per day of synthetic crude oil and unprocessed crude bitumen. This represents 35 per cent of Canada's total oil production. Current production capacity has increased to 1.0 million barrels per day (mbpd) due to new projects. This number may increase to 3.5 mbpd by 2017. Some new projects may be deferred due to the higher raw bitumen and synthetic crude oil supply costs. This presentation provided supply costs for a range of oil sands recovery technologies and production projections under various business scenarios. tabs., figs

  8. Fifth DOE symposium on enhanced oil and gas recovery and improved drilling technology. Volume 2. Oil

    Energy Technology Data Exchange (ETDEWEB)

    Linville, B. [ed.

    1979-01-01

    Volume 2 contains papers from the following sessions: residual oil determination; thermal methods; heavy oil-tar sands; technology transfer; and carbon dioxide flooding. Individual papers were processed.

  9. Luminescence monitoring of oil or tar contamination for industrial hygiene

    International Nuclear Information System (INIS)

    Gammage, R.B.; Vo-Dinh, T.

    1980-01-01

    Synfuel plants produce potentially carcinogenic oils and tars. Exposure of workers to these tars and oils is difficult to avoid completely and occurs via direct contact with dirty surfaces or condensation of escaped fumes onto or within the body. Surface skin, measurements are made directly with a near-ultraviolet luminoscope employing a fiber optics lightguide and a stethoscopic cap pressed against the skin. This instrument is especially suitable for measuring ng to μg/cm 2 amounts of residual contamination remaining on the surface of the skin after washing. To minimize the potential for carcinogenicity, the excitating ultraviolet light intensity is only 1/100th that of sunlight. (orig.)

  10. Tar sand extraction by steam stimulation and steam drive: measurement of physical properties

    Energy Technology Data Exchange (ETDEWEB)

    Linberg, W.R.

    1980-09-10

    The measurement of the following thermophysical properties of Utah tar sands is in progress: thermal conductivity, specific heat relative permeability, and viscosity (of the recovered bitumen). During the report period (October 1, 1978 to November 1, 1979), experimental procedures have been developed and a basic data set has been measured. Additionally, standard core analysis has been performed for four drill sites in the Asphalt Ridge, Utah area.

  11. Method of removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues

    Energy Technology Data Exchange (ETDEWEB)

    Palmquist, F T.E.

    1949-09-08

    A method is described for removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues by centrifuging in the presence of oil-dissolving and paraffin-precipitating solvents, by which the precipitated paraffin is made to pass through an indifferent auxiliary liquid, in which a removal of oil takes place, characterized in that as auxiliary liquid is used a liquid or mixture of liquids whose surface tension against the oil solution is sufficiently low for the paraffin to pass the layer of auxiliary liquid in the form of separate crystals.

  12. Developing new markets for oil sands products

    International Nuclear Information System (INIS)

    Crandall, G.

    2004-01-01

    This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

  13. Oil sands and the environment

    Energy Technology Data Exchange (ETDEWEB)

    Seeley, R. [Shell Canada Ltd., Calgary, AB (Canada). Calgary Research Centre

    2004-07-01

    Oil sands are a significant resource for Alberta and Canada with continuing growth opportunity. There is a need to ensure sustainable development of the oil sands resources from a social, economic and environmental perspective. The industry has succeeded in terms of proven reserves, technology advancements, reduced operating costs, reliability and market accessibility. Some of the major challenges facing the industry include high capital cost, infrastructure, social services and keeping pace with growth. This presentation outlined the proactive measures that the oil sands industry has taken to manage environmental issues such as sulphur dioxide and nitrogen oxide emissions, greenhouse gases, water management and land reclamation. tabs., figs.

  14. Alberta oil sands royalty regime

    International Nuclear Information System (INIS)

    Asgarpour, S.

    2004-01-01

    The long term objective of the Oil Sands Business Unit of Alberta Energy is to pave the way for Alberta's bitumen production to reach 3 million barrels per day by 2020. This presentation described the national government's role in resource development. It was emphasized that since the Crown is the owner of the oil sands resource, it would benefit by providing strategic leadership and by generating a larger royalty base. The oil sands fiscal regime was described with reference to generic royalty, risk sharing, investment, and project economics. Business rule principles were also outlined along with criteria for project expansions. Both upstream and downstream challenges and opportunities were listed. 4 figs

  15. Oil sands tailings management project

    Energy Technology Data Exchange (ETDEWEB)

    Godwalt, C. [Alberta WaterSMART, Calgary, AB (Canada); Kotecha, P. [Suncor Energy Inc, Calgary, AB (Canada); Aumann, C. [Alberta Innovates - Technology Futures, Alberta Governement, AB (Canada)

    2010-11-15

    The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

  16. Oil sands tailings management project

    International Nuclear Information System (INIS)

    Godwalt, C.; Kotecha, P.; Aumann, C.

    2010-11-01

    The Oil sands leadership initiative (OSLI) works with the Government of Alberta on the development of the oil sands industry, considering environmental, economical and social aspects. Water management was identified as one of most important areas to focus on. Alberta WaterSMART was requested to support the development and the management of projects resulting from the work done or underway in this field. The development of a regional water management solution stood out as the most interesting solution to obtain significant results. In the Athabasca Region, oil sands producers work independently on their water sourcing and disposal with particular attention to fresh water conservation and economics. The Athabasca River represents a source for mines and distant saline aquifers are the target of steam assisted gravity drainage (SAGD) operators. As part of a four-phase project aiming to study the environmental and economic footprint (EEF) benefit of alternatives for Athabasca oil sands production water supply and disposal, the purpose of the tailings water management project was to identify tailings treatment technologies that are ready to be implemented, and to design and evaluate solutions in order to improve regional oil sands production water sourcing and disposal. Alternatives were evaluated based on their total EEF, applying a lifecycle assessment methodology with a particular attention on the quantification of important performance indicators. 25 refs., 8 tabs., 40 figs.

  17. Nuclear energy in the oils sands

    International Nuclear Information System (INIS)

    Arsenault, J.E.

    2014-01-01

    The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

  18. Nuclear energy in the oils sands

    Energy Technology Data Exchange (ETDEWEB)

    Arsenault, J.E.

    2014-09-15

    The major Canadian oil sands are located in Alberta and Saskatchewan, with most production from the strata along the Athabasca River in Alberta. The economically recoverable oil sands reserves are estimated to be 168 billion barrels which at a current production rate of 1.8 million barrels per day (2012), are projected to last a very long time. Canada has been blessed with vast energy resources which make it potentially energy-independent and able to provide significant exports but there are concerns that their development cannot be managed in a wholly acceptable manner. Comparable concerns have been applied to nuclear energy in the past and in recent times to the oil sands. The technologies associated with these energy sources have always been controversial because they are at the confluence of economics and politics where finding a balance between risk and reward is difficult. So it should be no surprise that when these technologies get linked together in certain proposals their prospect for success is doubly difficult. The possible use of nuclear energy for production of oil from the oil sands dates back to the late 1950s, when an experiment to mine the oil by detonating an underground nuclear device was proposed. It was predicted that the heat and pressure released from such a device would create a large cavern into which oil would flow, and from where it would be pumped to the surface. Almost at the same time, oil sands research using conventional sources of energy had culminated with the development of practical refining processes, essentially those still in use today. These methods require large amounts of heat energy in the form of hot water and steam. In this century nuclear energy was proposed as the source for the heat required by the oil sands production processes. To date neither of these nuclear proposals for oil sands projects have been successful, because the economic and political balance could not be struck. (author)

  19. Geotechnical properties of crude oil contaminated sand

    International Nuclear Information System (INIS)

    Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

    1994-01-01

    Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

  20. Dehydration of hydrated low-temperature tar

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T

    1949-01-01

    Yoshida examined the mechanism of the dehydration of hydrated low-temperature tar with a microscope. The tar containing free carbon and coal dust is so stable that the removal of the above substances and water by a physical method is very difficult. Addition of light oil produced by fractionation of low-temperature tar facilitates the operations. Yoshida tried using the separate acid, neutral, and basic components of the light oil; the acid oil proved to be most effective. For many reasons it is convenient to use light oil as it is. In this method the quantity of light oil required is 2 to 3 times that of tar. But in supplementing the centrifugal method, the quantity of light oil needed might be only half the amount of tar.

  1. Aging effects on oil-contaminated Kuwaiti sand

    International Nuclear Information System (INIS)

    Al-Sanad, H.A.; Ismael, N.F.

    1997-01-01

    Large quantities of oil-contaminated sands resulted from the destruction of oil wells and the formation of oil lakes in Kuwait at the end of the Gulf Wa/r. A laboratory testing program was carried out to determine the geotechnical properties of this material and the effect of aging on their properties. Tests included direct shear, triaxial, and consolidation tests on clean and contaminated sand at the same relative density. The influence of aging was examined by testing uncontaminated sand after aging for one, three, and six months in natural environmental conditions. The results indicated increased strength and stiffness due to aging and a reduction of the oil content due to evaporation of volatile compounds. The factors that influence the depth of oil penetration in compacted sand columns were also examined including the type of oil, relative density, and the amount of fines

  2. Stakeholder relations in the oil sands : managing uncertainty

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-05-15

    Alberta's oil sands are now at the crossroads of a series of significant and complex global issues that will require careful negotiation by all stakeholders involved in the oil sands industry. This paper discussed methods of managing uncertainty and risk related to the oil sands industry's agenda for the future. Oil sands developers must continue to secure permission from communities and other key stakeholders in order to develop oil sand projects. Stakeholder relations between oil sands operators, First Nations, and Metis Nation communities must ensure that respect is maintained while environmental impacts are minimized and long-term economic benefits are secured for all parties. Environmental non-governmental organizations (ENGOs) must ensure that oil sands resources are developed responsibly, and that environmental standards are maintained. Seven key shifts in stakeholder relations resulting from the recent economic crisis were identified. These included (1) withdrawal from the multi-stakeholder process, (2) increased focus on government to demonstrate policy leadership, (3) a stronger push from ENGOs to express environmental concerns, (4) global lobby and public relations efforts from ENGOs, (5) companies retreating to local community stakeholders, (6) more active demands from First Nations and Metis Nations groups, and (7) companies challenging ENGO campaigns. The study concluded by suggesting that government leadership is needed to clear policy and regulatory frameworks for Canada's oil sands.

  3. Oil sands and heavy oil development issues and prospects under a Liberal government

    International Nuclear Information System (INIS)

    Shiry, J.

    1993-01-01

    A short review is presented of some of the factors affecting development of the western Canadian oil sands and heavy oil deposits to the year 2000. The Alberta oil sands resource has at least 1 trillion bbl of recoverable oil. At current prices, technology is the key to reducing costs to a more economic level. Cash operating costs have halved to $15/bbl over the past decade and the oil sands companies have programs to halve that figure again. A problem is the rising cost of natural gas as a fuel, which could jeopardize further development of both oil sand and heavy oil resources. In Saskatchewan, over 25 billion bbl of heavy oil are estimated to be in place. The biggest question is what percentage can be recovered; again, technology such as horizontal wells, 3-dimensional seismic, and steam assisted recovery is playing an important role. Concerns are expressed about the intentions of the new Liberal government concerning oil sand/heavy oil development, especially on the issues of foreign investment, exports, and environmental policy. A Liberal energy policy is not likely to allow U.S. direct investment in an oil sands plant to be tied to export of production, and the energy- and emissions-intensive nature of the oil sand/heavy oil industry will tend to make environmental approvals difficult

  4. The Canadian oil sands--a sticky future

    Energy Technology Data Exchange (ETDEWEB)

    Cowtan, S A

    1977-01-01

    The oil sands have been known for 200 yr but only over the last decade have they been recognized as a potential major energy source for Canada. The study looks at the present GCOS plant, and briefly discusses Canada's future energy requirements and how she might fill those requirements from conventional and nonconventional sources, such as the Frontier areas, oil sands mining, oil sands in situ, and heavy oil. The economics and the future of these sources and the environment necessary for their development are analyzed.

  5. Oil sands economic impacts Canada : CERI report : backgrounder

    International Nuclear Information System (INIS)

    2005-09-01

    Oil sands production now accounts for 1 out of every 2 barrels of supply in Western Canada. It is anticipated that Alberta's oil sands sector will experience significant growth over the next few decades. This paper provided an outline of the challenges and economic impacts resulting from oil sands development in Canada. Alberta's oil sands reserves are estimated at 175 billion barrels that are deemed economically recoverable using current technology. At current production levels, reserves will sustain production of 2.5 million barrels per day for the next 200 years. A study by the Canadian Energy Research Institute (CERI) has forecast $100 billion in investment for the 2000-2020 period. Numerous companies hold leases and are planning new projects. A number of recent advances in oil sands technology are expected to further reduce costs as development matures. A royalty and tax regime that provides long-term fiscal certainty is a key factor that supports current oil sands growth forecasts. The CERI study has indicated that economic spinoffs from oil sands development relate to employment generated outside of Alberta, and that the largest percentage of government revenue accrues to the federal government. However, development may be constrained because the pace of growth in the sector may exceed underlying infrastructure related to roads, housing and municipal services. An adequate workforce of qualified trades and technical and professional people is also crucial. Several pipeline projects have been proposed to deliver oil sands crudes to new markets over the next decade. It was concluded that the billions of dollars invested in oil sands in Alberta will contribute to the economic prosperity of the entire country. 11 figs

  6. Upgrading of hydropyrolysis coal tar by hydroprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Haglund, R.; Otterstedt, J.E.; Sterte, J. (Chalmers Univ. of Tech., Goeteborg (Sweden). 1. Dept. of Engineering Chemistry)

    1991-05-01

    Upgrading of a hydropyrolysis coal tar by hydroprocessing was investigated using different process conditions. The response of the hydropyrolysis tar to hydroprocessing was compared to those of a conventional coal tar and two heavy oil fractions. At comparable conditions, the removal of heteroatoms from the hydropyrolysis tar was more effective than from the conventional tar and, in particular, than from the oil fractions. Using conditions typical for hydroprocessing of heavy oil fractions, the contents of N, O as well as S in the hydropyrolysis tar were reduced by more than 90%. Hydroprocessing also resulted in a considerable increase in the gasoline fraction of the tar. (orig.).

  7. Alberta Oil Sands Equity annual report, 1992-93. Partnership and progress in Alberta's oil sands development

    International Nuclear Information System (INIS)

    1993-01-01

    Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces ca 12% of Canadian crude oil requirements, and AOSE's share yielded $44 million profit for 1992/93, slightly higher than the the $43.3 million the previous year. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1993, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader opened Noveber 20, 1992, and production has reached 41,000 bbl/d, or 89% of design capacity. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 5 figs., 3 tabs

  8. Alberta Oil Sands Equity annual report, 1991-92. Partnership and progress in Alberta's oil sands development

    International Nuclear Information System (INIS)

    1992-01-01

    Alberta Oil Sands Equity (AOSE) manages the Alberta government's equity investments in oil sands and heavy oil projects. AOSE is a 16.74% participant in the Syncrude Project, a 10% participant in the OSLO (Other Six Leases Operation) Commercial Project and the OSLO New Ventures project, and a 24.17% participant in the Lloydminster Bi-Provincial Upgrader. Syncrude produces over 11% of Canadian crude oil requirements, and AOSE's share yielded $43.3 million profit for 1991/92, down significantly from the $82.1 million the previous year due to lower oil prices. The OSLO Commercial Project is a proposed commercial oil sands plant with a mine site and extraction plant to be located north of Fort McMurray, and an upgrading facility to be situated north of Edmonton. Work on this project was suspended in early 1992. The OSLO New Ventures project will handle the exploration and development of the remaining five oil sands leases plus the southern portion of Lease 31. As of March 31, 1992, the project owners were considering a commercial demonstration project utilizing dredging and cold-water extraction processes. Two of the owners are unable to provide funding and discussions are under way to resolve the matter and move the program forward. The Lloydminster Bi-Provincial Upgrader was nearly 90% complete in March 1992 and full startup is expected in November 1992; engineering work was completed in March 1991. The upgrader will increase the value of heavy crude oil and thereby increase its demand. 4 figs., 4 tabs

  9. Mobil Oil Canada : Kearl Oil Sands Mine

    International Nuclear Information System (INIS)

    1997-01-01

    The upgrader design at Mobil's Kearl Oil Sands Mine were described. Included were feed characteristics, upgrader products, process schemes and their overall economics and upgrader technologies in use, including coking, deasphalting, hydrocracking, hydrotreating and visbreaking. Advantages and disadvantages of the upgrader technologies were highlighted. As far as the product is concerned, much of it is destined to U.S. refineries that are equipped to process the material. The Kearl Oil Sands Mine upgrading facility will likely use a combination of coker/hydrotreating, which is a well proven process for high value products that has been used in all five of Mobil's refineries in the U.S., and visbreaker/deasphalting, which has shown promise in bench-scale testing, but at present still has some potential commercial difficulties. Foremost among these are the high softening product of asphalt from visbroken products, questionable commercial feasibility of the low yield of pitch, and problems in the disposal of asphalt. Severe visbreaking also yields unstable products. Details of Mobil Canada's oil sands project were also summarized 2 tabs., 9 figs

  10. Economic impacts of Alberta's oil sands, volume 1

    International Nuclear Information System (INIS)

    Timilsina, G.R.; LeBlanc, N.; Walden, T.

    2005-01-01

    In 2004, the international media recognized Alberta's oil sands as part of the global oil reserves, thereby establishing Canada as second to Saudi Arabia as potential oil producing nations. The economic impacts of Alberta's oil sands industry on economies were assessed at regional, provincial and international levels for the 2000 to 2020 period. A customized input-output model was used to assess economic impacts, which were measured in terms of changes in gross domestic product; employment and labour income; and, government revenues. Cumulative impacts on employment by sector and by jurisdiction were also presented. An investment of $100 billion is expected through 2020, resulting in production of crude bitumen and synthetic crude oil outputs valued at about $531 billion. The impact of the oil sands industry on local employment was also evaluated. It was shown that activities in the oil sands industry will lead to significant economic impact in Alberta, Ontario, Quebec and the rest of Canada. Alberta's local economy would be the main beneficiary of oil sands activities with nearly 3.6 million person years employment created in Alberta during the 2000 to 2020. Another 3 million person years employment would be created in other Canadian provinces and outside Canada during the same time period. A sensitivity analysis on the responsiveness to oil prices and the removal of various constraints incorporated in the main analysis was also presented. The federal government will be the largest recipient of revenues generated to to oil sands activities. The results of the study were compared with that of the National Task Force on Oil Sands Strategies. This first volume revealed the results of the study while the second volume includes the data and detailed results. 48 refs., 57 tabs., 28 figs

  11. Proceedings of the oil sands and heavy oil technologies conference and exhibition

    International Nuclear Information System (INIS)

    2009-01-01

    This conference provided a forum for oil sands industry leaders to review the current and future state of technology in this frontier environment. Presentations were delivered by key personnel involved in groundbreaking projects with a renewed focus on oil sands technology and equipment, viewed from the strategic level with case studies and reports on application technologies designed to optimize oil sands operations. The presentations addressed a wide range of issues related to the environmental impacts of oil sands processing facilities, including innovative water and wastewater solutions for heavy oil producers for bitumen mining, in-situ and upgrading facilities. New advances in sulphur treatment technologies were highlighted along with technologies designed to increase the energy efficiency and energy consumption rates of upgrader and processing facilities. Advances in carbon dioxide (CO 2 ) capture and storage systems were also discussed along with geopolitical and economic evaluations of the future of the oil sands industry. The conference featured 59 presentations, of which 48 have been catalogued separately for inclusion in this database. refs., tabs., figs

  12. Mitigating in situ oil sands carbon costs

    Energy Technology Data Exchange (ETDEWEB)

    Theriault, D.J.; Peterson, J. [Laricina Energy Ltd., Calgary, AB (Canada); Heinrichs, H. [Canadian Chemical Technology Inc., Calgary, AB (Canada)

    2008-10-15

    Carbon capture and sequestration is a complex problem with a variety of dimensions that need to be considered. The political, social, and regulatory pressures are forcing carbon costs on the oil sands industry in an effort to reduce the carbon footprint of oil sands operations. This paper reviewed the political, social, and regulatory pressures and obligations for the in-situ oil sands industry. It presented the views and insights of Laricina Energy on the carbon challenge. It also described the initiatives that Laricina Energy is taking to manage these imperatives and outlined the challenges the industry is facing. The purpose of the paper was to encourage dialogue and collaboration by the oil sands industry. The paper also described the dimensions of the carbon problem and how the industry can contribute to a solution. Last, the paper reviewed the parameters of carbon dioxide or greenhouse gas containment and storage issues. It was concluded that the regulatory and policy requirements need to be clarified so that industry understands the new business landscape as well as the requirements that influence the economics of in-situ oil sands development. 7 refs., 7 figs.

  13. Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

    Energy Technology Data Exchange (ETDEWEB)

    Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

    2015-09-30

    This report summarizes the significant findings from the Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources program sponsored by the Department of Energy through the National Energy Technology Laboratory. There were four principle areas of research; Environmental, legal, and policy issues related to development of oil shale and oil sands resources; Economic and environmental assessment of domestic unconventional fuels industry; Basin-scale assessment of conventional and unconventional fuel development impacts; and Liquid fuel production by in situ thermal processing of oil shale Multiple research projects were conducted in each area and the results have been communicated via sponsored conferences, conference presentations, invited talks, interviews with the media, numerous topical reports, journal publications, and a book that summarizes much of the oil shale research relating to Utah’s Uinta Basin. In addition, a repository of materials related to oil shale and oil sands has been created within the University of Utah’s Institutional Repository, including the materials generated during this research program. Below is a listing of all topical and progress reports generated by this project and submitted to the Office of Science and Technical Information (OSTI). A listing of all peer-reviewed publications generated as a result of this project is included at the end of this report; Geomechanical and Fluid Transport Properties 1 (December, 2015); Validation Results for Core-Scale Oil Shale Pyrolysis (February, 2015); and Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach (November, 2014); Policy Issues Associated With Using Simulation to Assess Environmental Impacts (November, 2014); Policy Analysis of the Canadian Oil Sands Experience (September, 2013); V-UQ of Generation 1 Simulator with AMSO Experimental Data (August, 2013); Lands with Wilderness Characteristics, Resource Management Plan Constraints, and Land Exchanges

  14. A Primer on Alberta’s Oil sands Royalties

    Directory of Open Access Journals (Sweden)

    Sarah Dobson

    2015-12-01

    Full Text Available Fulfilling its campaign promise, the new NDP government announced a review of Alberta’s royalty framework in June 2015. The province receives royalty revenue from three main sources – natural gas, crude oil, and oil sands. Since the 2009-10 fiscal year the largest contributor to Alberta’s royalty revenues has been the oil sands. If you want a sense of how important oil sands royalties have been for Alberta’s finances, consider this: In the 2014–15 fiscal year, the government collected just over $5 billion from oil sands royalties. These royalties covered over 10 per cent of the province’s operational expenses of $48.6 billion in the same fiscal year. Over the last six fiscal years the oil sands have contributed an average of 10 per cent of revenues to provincial coffers. This makes oil sands royalties the fourth largest contributor behind personal income taxes (23 per cent, federal transfers (13 per cent and corporate income taxes (11 per cent. But how many Albertans really understand how the royalty system works? What do we mean when we say “royalty”? How does the Alberta Government calculate royalties on oil sands producers? If the system is going to change, it’s important that Albertans understand how the current system works. That is what this paper is designed to do. For Albertans to properly judge the impact of new policy, they need a solid understanding of the current policy environment. We all know that oil prices have dropped and oil sands producers are losing profitability. As such, changes to the royalty system could have a deep and profound impact on the sector. Here are some of the issues this primer will study: • Pre-payout projects vs. post-payout projects, in other words, the classification of projects for royalty purposes based on whether the cumulative costs of a project exceed its cumulative revenues • Monthly payment of royalties vs. annual payment • Understanding the unit price of bitumen and how that

  15. Big picture thinking in oil sands tailings disposal

    Energy Technology Data Exchange (ETDEWEB)

    Boswell, J. [Thurber Engineering Ltd., Calgary, AB (Canada)

    2010-07-01

    This PowerPoint presentation discussed methods of disposing oil sands tailings. Oil sands operators are currently challenged by a variety of legislative and environmental factors concerning the creation and disposal of oil sands tailings. The media has focused on the negative ecological impact of oil sands production, and technical issues are reducing the effect of some mitigation processes. Operators must learn to manage the interface between tailings production and removal, the environment, and public opinion. The successful management of oil sand tailings will include procedures designed to improve reclamation processes, understand environmental laws and regulations, and ensure that the cumulative impacts of tailings are mitigated. Geotechnical investigations, engineering designs and various auditing procedures can be used to develop tailings management plans. Environmental screening and impact assessments can be used to develop sustainable solutions. Public participation and environmental mediation is needed to integrate the public, environmental and technical tailings management strategies. Operators must ensure public accountability for all stakeholders. tabs., figs.

  16. Geotechnical properties of oil-contaminated Kuwaiti sand

    Energy Technology Data Exchange (ETDEWEB)

    Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F. [Kuwait Univ., Safat (Kuwait). Dept. of Civil Engineering

    1995-05-01

    Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction.

  17. Geotechnical properties of oil-contaminated Kuwaiti sand

    International Nuclear Information System (INIS)

    Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F.

    1995-01-01

    Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction

  18. Preliminary fingerprinting analysis of Alberta oil sands and related petroleum products

    International Nuclear Information System (INIS)

    Yang, C.; Wang, Z.D.; Hollebone, B.; Brown, C.E.; Yang, Z.Y.; Landriault, M.; Fieldhouse, B.

    2009-01-01

    This paper reported on a study that presented a preliminary quantitative chemical characterization of Alberta oil sands and many other related Alberta oils such as oil sand bitumen, Cold Lake bitumen, Albian heavy synthetic crude, and Alberta Mixed sweet blend. The rapid increase in production of the Alberta oil sands has resulted in unprecedented environmental concern. The mining, extraction and production of oil sands such resulted in huge consumption of water resources, huge emission of greenhouse gas and large number of tailings ponds. In addition, accidental spills in the transportation and usage of oil sands will potentially cause considerable impact on the environment. It is therefore essential to have the ability to characterize Alberta oil sands and their oil products. The specific chemical properties of the oil sands bitumen must be known. Therefore, this study collected quantitative data on the concentration and distribution profiles of target compounds in Alberta oil sands and its petroleum products. The chemical fingerprints of 5 Alberta oil sands and their related petroleum products were studied using gas chromatography/flame ionization detection (GC/FID) and gas chromatography/mass spectrometry (GC/MS). The characterized hydrocarbons were n-alkanes; target alkylated PAHs and other EPA priority PAHs; biomarker terpanes and steranes; and bicyclic sesquiterpanes. The information acquired during this study will provide the basis for oil-oil correlation and differentiation in future environmental applications relevant to oil sands. 24 refs., 6 tabs., 4 figs.

  19. Comparative analysis of fiscal terms for Alberta oil sands and international heavy and conventional oils

    International Nuclear Information System (INIS)

    Van Meurs, P.

    2007-01-01

    There are considerable differences between international heavy oil and Alberta oil sands projects, notably the high viscosity of the bitumen in the oil sands reservoirs. The oil sands bitumen do not flow to wells without heating the bitumen, thereby adding to the already high cost of Alberta oil sand operations. This report provided an economic comparison of Alberta oil sands and international heavy oil projects. It also included a brief scoping review to compare with conventional oil regimes. Full exploration costs including the costs of dry holes were allocated to conventional oil operations in order to obtain a proper comparison. This investigation included the costs of dry holes. The report was a follow up to an earlier study released on April 12, 2007 on the preliminary fiscal evaluation of Alberta oil sand terms. The report provided an economic framework and described project selection. It then provided a discussion of production, costs and price data. Four adjusted projects were presented and compared with Alberta. The Venezuelan royalty formula was also discussed. Last, the report provided a detailed fiscal analysis. Comparisons were offered with Cold Lake and Athabasca Mine. A review of some other fiscal systems applicable to conventional oil were also outlined. It was concluded that Alberta oil sands developments are very competitive. It would be possible to modestly increase government revenues, without affecting the international competitive position of Alberta with respect to conventional oil. There is also some possibility to increase the base royalty on the Alberta oil sands without losing competitiveness. tabs., figs

  20. Sustainable water management in Alberta's oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Byers, Bill; Usher, Robyn; Roach, Andrea [CH2M HILL, Englewood, CO (United States); Lambert, Gord; Kotecha, Prit [Suncor Energy Inc., Calgary (Canada)

    2012-07-01

    The Canadian Association of Petroleum Producers forecast published in 2011 predicts that oil production from oil sands will increase by 50% in the next 3 years and double by 2020. This rate of growth will result in significant pressure on water resources; water use per barrel of oil sands production is comparable to other energy resources - about 2.5 barrels of fresh water per barrel of oil produced are used by mining operations and 0.5 barrels by in-situ operations. Suncor Energy Inc. (Suncor) was the first company to develop the oil sands in northern Alberta and holds one of the largest oil sands positions in Canada. In 2010, Suncor announced plans to increase production to more than 1 million barrels of oil equivalent per day by 2020, which it plans to achieve through oil sands production growth of approximately 10% per year. Because water supply and potential impacts to water quality are critical to its future growth, in 2010-2011 Suncor conducted a risk assessment to identify water-related business risks related to its northern Alberta operations. The assessment identified more than 20 high level business risks in strategic water risk areas including water supply, water reuse, storm water management, groundwater, waste management and river water return. The risk assessment results prompted development of a strategic roadmap to guide water stewardship across Suncor's regional operations. The roadmap describes goals, objectives, and specific activities for each of six key water risk areas, and informs prioritization and selection of prospective water management activities. Suncor is not only exploring water within its own boundaries, but is also collaborating with other oil sands producers to explore ways of integrating its water systems through industry consortia; Suncor is a member of the Oil Sands Leadership Initiative and of the recently formed Canadian Oil Sands Innovation Alliance, among others. (author)

  1. Preparation of pure phenols from tars

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, J

    1933-02-07

    A process is disclosed for the preparation of pure phenols from brown coal tar, shale tar, or primary tar, characterized in that the raw oil obtained from the tar is carefully fractionated, in a suitable way without or with a slight pressure decrease, or before the fractionation the raw oil is heated to free the prepared phenolate solution from impurities after successful oxidation by passing in steam at a temperature between 100 and 120/sup 0/C.

  2. Opportunities for CANDU for the Alberta oil sands

    International Nuclear Information System (INIS)

    Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Hau, K.; Zhou, X.; Dunbar, R.B.

    2003-01-01

    The Alberta oil sands bitumen deposits comprise of one of the largest sources hydrocarbon in the world, and have emerged as the fastest growing, soon to be dominant, source of crude oil in Canada. The oil industry has made great strides in improving the effectiveness of gathering this resource. In particular, alternatives to open-pit mining have been developed which enable in-site recovery of underground deposits with a minimum of environmental disruption. The main challenge that remains is the large quantity of energy needed in the process of extracting the oil and upgrading it to commercial levels. For a typical in-situ extraction project, about 18% of the energy content of the oil produced is used up in the extraction process, while a further 5% is used in generating hydrogen to upgrade the bitumen to synthetic crude oil. Looking ahead, even as improvements in energy use efficiency, (and hydrocarbon use efficiency) counterbalance the increases in hydrocarbon demand from economic growth (particularly in the developing world), Canada and Alberta recognize that the oil sands resource will be needed, and both support the development of this resource in an environmentally responsible way. The large energy requirement for the oil sands extraction process represents a challenge with regard to both environmental impact and security of supply. The use of natural gas, the current energy supply, has impacts in terms of air quality (via NOX and other emissions) and also represents a large greenhouse gas emissions component. As the oil sands industry expands, the availability of natural gas also becomes a concern, as does price and price stability. With this background, the opportunity for nuclear reactors to provide an economical, reliable, virtually zero-emission source of energy for the oil sands becomes very important. Over the last few years, developments in oil sands extraction technology, and developments in CANDU technology through the Advanced CANDU Reactor, (ACR

  3. Polycyclic aromatic hydrocarbons (PAHs) and hopanes in stranded tar-balls on the coasts of peninsular Malaysia: applications of biomarkers for identifying sources of oil pollution

    International Nuclear Information System (INIS)

    Zakaria, Mohamad Pauzi; Okuba, Tomoaki; Takada, Hideshige

    2001-01-01

    Malaysian coasts are subjected to various threats of petroleum pollution including routine and accidental oil spill from tankers, spillage of crude oils from inland and offshore oil fields, and run-off from land-based human activities. Due to its strategic location, the Straits of Malacca serves as a major shipping lane. This paper expands the utility of biomarker compounds, hopanes, in identifying the source of tar-balls stranded on Malaysian coasts. 20 tar-ball samples collected from the east and west coast were analysed for hopanes and polycylic aromatic hydrocarbons (PAHs). Four of the 13 tar-ball samples collected from the west coast of Peninsular Malaysia were identified as the Middle East crude oil (MECO) based on their biomarker signatures, suggesting tanker-derived sources significantly contributing the petroleum pollution in the Straits of Malacca. The tar-balls found on the east cost seem to originate from the offshore oil platforms in the South China Sea. The presence of South East Asian crude oil (SEACO) tar-balls on the west coast carry several plausible explanations. Some of the tar-balls could have been transported via sea currents from the east coast. The tankers carrying SEACO to other countries could have accidentally spilt the oil as well. Furthermore, discharge of tank washings and ballast water from the tankers were suggested based on the abundance in higher molecular weight n-alkanes and the absence of unresolved complex mixture (UCM) in the tar-ball samples. The other possibilities are that the tar-balls may have originated from the Sumatran oil fields and spillage of domestic oil from oil refineries in Port Dickson and Malacca. The results of PAHs analysis suggest that all the tar-ball samples have undergone various extent of weathering through evaporation, dissolution and photo-oxidation. (Author)

  4. Polycyclic aromatic hydrocarbon (PAHs) and hopanes in stranded tar-balls on the coasts of Peninsular Malaysia: applications of biomarkers for identifying sources of oil pollution.

    Science.gov (United States)

    Zakaria, M P; Okuda, T; Takada, H

    2001-12-01

    Malaysian coasts are subjected to various threats of petroleum pollution including routine and accidental oil spill from tankers, spillage of crude oils from inland and off-shore oil fields, and run-off from land-based human activities. Due to its strategic location, the Straits of Malacca serves as a major shipping lane. This paper expands the utility of biomarker compounds, hopanes, in identifying the source of tar-balls stranded on Malaysian coasts. 20 tar-ball samples collected from the east and west coast were analyzed for hopanes and polycyclic aromatic hydrocarbons (PAHs). Four of the 13 tar-ball samples collected from the west coast of Peninsular Malaysia were identified as the Middle East crude oil (MECO) based on their biomarker signatures, suggesting tanker-derived sources significantly contributing the petroleum pollution in the Straits of Malacca. The tar-balls found on the east coast seem to originate from the offshore oil platforms in the South China Sea. The presence of South East Asian crude oil (SEACO) tar-balls on the west coast carry several plausible explanations. Some of the tar-balls could have been transported via sea currents from the east coast. The tankers carrying SEACO to other countries could have accidentally spilt the oil as well. Furthermore, discharge of tank washings and ballast water from the tankers were suggested based on the abundance in higher molecular weight n-alkanes and the absence of unresolved complex mixture (UCM) in the tar-ball samples. The other possibilities are that the tar-balls may have been originated from the Sumatran oil fields and spillage of domestic oil from oil refineries in Port Dickson and Malacca. The results of PAHs analysis suggest that all the tar-ball samples have undergone various extent of weathering through evaporation, dissolution and photooxidation.

  5. Microbial metabolism alters pore water chemistry and increases consolidation of oil sands tailings.

    Science.gov (United States)

    Arkell, Nicholas; Kuznetsov, Petr; Kuznetsova, Alsu; Foght, Julia M; Siddique, Tariq

    2015-01-01

    Tailings produced during bitumen extraction from surface-mined oil sands ores (tar sands) comprise an aqueous suspension of clay particles that remain dispersed for decades in tailings ponds. Slow consolidation of the clays hinders water recovery for reuse and retards volume reduction, thereby increasing the environmental footprint of tailings ponds. We investigated mechanisms of tailings consolidation and revealed that indigenous anaerobic microorganisms altered porewater chemistry by producing CO and CH during metabolism of acetate added as a labile carbon amendment. Entrapped biogenic CO decreased tailings pH, thereby increasing calcium (Ca) and magnesium (Mg) cations and bicarbonate (HCO) concentrations in the porewater through dissolution of carbonate minerals. Soluble ions increased the porewater ionic strength, which, with higher exchangeable Ca and Mg, decreased the diffuse double layer of clays and increased consolidation of tailings compared with unamended tailings in which little microbial activity was observed. These results are relevant to effective tailings pond management strategies. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  6. Modelling the behavior of an oil saturated sand

    International Nuclear Information System (INIS)

    Evgin, E.; Altaee, A.; Lord, S.; Konuk, I.

    1990-01-01

    The experiments carried out in an earlier study show the oil contamination affects the strength and deformation characteristics of a crushed quartz sand. In the present study, a mathematical soil model is used to simulate the mechanical behavior of the same sand. The model parameters are determined for both clean and oil contaminated soil. Simulations are made for the stress-strain behavior of the soil in drained and undrained conventional traixial compression tests. In order to illustrate the effect of changes in the soil properties on the behavior of an engineering structure, a finite element analysis is carried out. In this paper comparative results are presented to show the differences in the behavior of a foundation resting on a clean sand, on an oil contaminated sand, and on a sand contaminated locally

  7. The tar sands of the USA : with permits now in hand, a Calgary company is a cash injection away from producing oil from America's first oilsands mine

    Energy Technology Data Exchange (ETDEWEB)

    Jaremko, D.

    2010-06-15

    A Canadian company has recently received approval to develop large oil sands mining operations in Utah. Earth Energy Resources is now raising the finances required to commercialize its operations in the state. Utah's oil sands reserves are currently estimated at between 20 to 32 billion barrels. However, the impacts of oil sands operations are of concern to some environmental groups, who worry that Utah will become a duplicate of Alberta's Athabasca region. The planned project is a 2000 barrel-per-day pilot project. Regulators in Utah have received negative responses from the public after advertising the potential project in local newspapers, and demonstrations have been held in the state's capital. Oil sands are already being developed at 2 installations in Utah, with the bitumen currently being sold as asphalt products. The state is also home to significant oil shale reserves. Operators in the region plan to design compact, well-contained mines in order to maintain transportability. 3 figs.

  8. Market opportunities and challenges for oil sands

    International Nuclear Information System (INIS)

    Wise, T.H.

    2004-01-01

    The use of Alberta bitumen as a clean fuel depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production from the Western Canada Sedimentary Basin. The challenges facing the oils sands processing industry include: crude oil prices which affect the producer's market; market expansion options; diluent availability/cost; supply cost competitiveness; and, regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. It was noted that Alberta must retain or increase its share of the Midwest market. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. New pipeline capacity is needed to reach more distant markets such as Southern Midwest, Washington, and California. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. 13 figs

  9. Acute toxicity of birch tar oil on aquatic organisms

    Directory of Open Access Journals (Sweden)

    M. HAGNER

    2008-12-01

    Full Text Available Birch tar oil (BTO is a by-product of processing birch wood in a pyrolysis system. Accumulating evidence suggests the suitability of BTO as a biocide or repellent in terrestrial environments for the control of weeds, insects, molluscs and rodents. Once applied as biocide, BTO may end up, either through run-off or leaching, in aquatic systems and may have adverse effects on non-target organisms. As very little is known about the toxicity of BTO to aquatic organisms, the present study investigated acute toxicity (LC50/EC50 of BTO for eight aquatic organisms. Bioassays with the Asellus aquaticus (crustacean, Lumbriculus variegatus (oligochaeta worm, Daphnia magna (crustacean, Lymnea sp. (mollusc, Lemna minor (vascular plant, Danio rerio (fish, Scenedesmus gracilis (algae, and Vibrio fischeri (bacterium were performed according to ISO, OECD or USEPA-guidelines. The results indicated that BTO was practically nontoxic to most aquatic organisms as the median effective BTO concentrations against most organisms were >150 mg L-1. In conclusion, our toxicity tests showed that aquatic organisms are to some extent, invariably sensitive to birch tar oil, but suggest that BTO does not pose a severe hazard to aquatic biota. We deduce that, unless BTOs are not applied in the immediate vicinity of water bodies, no special precaution is required.;

  10. Growing markets to sustain oil sands development

    International Nuclear Information System (INIS)

    Wise, T.H.

    2003-01-01

    The utilization of Alberta bitumen for the clean fuels market depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production in Western Canada. Several issues pose a challenge to the oil sands processing industry. The producers' market is affected by crude oil prices, market expansion options, diluent availability/cost, supply cost competitiveness, and regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. A brief review of markets for Canadian crude oil, including synthetic crude, was provided. The share of the Midwest market by Alberta must be retained and increased. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. To reach more distant markets such as Southern Midwest, Washington, and California, new pipeline capacity would be required. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. tabs., figs

  11. Proceedings of the Canadian oil sands forum 2007 : creating excellence through innovation

    International Nuclear Information System (INIS)

    2007-01-01

    The supply from Canada's oil sands industry is growing at an accelerated pace. This conference was intended for professionals in the oil sands industry seeking updated information on oil sands developments, transportation issues and future market challenges and opportunities. It was attended by a broad range of industry participants who addressed some of the critical issues involved in developing oil sands projects. Despite market opportunities which have resulted in a fast pace of development and continually evolving project plans, there are challenges and uncertainties that must be overcome in order to achieve projected levels of supply growth. It was noted that the business environment in the oil sands industry is continually changing in terms of current supply/market/refining situations and new market developments. The conference also addressed how capital cost and mega-project management issues are being addressed. Expanding market opportunities for Canada's growing oil sands supply were highlighted along with latest developments related to upgrading strategies. Market experts also discussed issues related to synthetic crude, heavy oil markets and the supply and demand of diluents. The sessions were entitled: challenges and opportunities in oil sands; oil sands business outlook; latest project development updates; integration of Canadian oil sands with U.S. refining; and, technology and oil sands innovations.The conference featured 16 presentations, of which 6 have been catalogued separately for inclusion in this database. tabs., figs

  12. Chemical-composition studies of low-temperature-carbonization coal tar

    Energy Technology Data Exchange (ETDEWEB)

    Edel' shtein, N G; Lanin, V A

    1955-01-01

    Pintsch-oven low-temperature tar was separated into its constituents by conventional methods, and the average of 2 results was neutral asphaltenes 12.56, basic asphaltenes 2.61, acid asphaltenes 18.82, phenols 13.23, bases 2.31, neutral oil 17.66, crystalline paraffins 7.34, silica-gel tars (I) (benzene extract) 15.40, I (acetone extract) 2.47, carbenes 0.45, and carbides and dust 1.44%. The low-temperature-tar asphaltenes and tars differ from shale-oil tars by being lower in C and higher in H, with a considerably higher C:H ratio. Their specific gravity is somewhat higher, and they are cyclic in structure. The asphaltenes and silica-gel tars of coal tar and shale oil were hydrogenated, molecular weights d/sub 4//sup 20/ and n/sub 4//sup 20/ of the separated compounds were determined, and empirical formulas of the hydrogenated compounds calculated. The neutral oil was separated into saturated, intermediate (iodine number 23), unsaturated (iodine number 51), a small quantity of a mixture of unsaturated and aromatic hydrocarbons, and 44.9% aromatic hydrocarbons. While naphthenes seem to be predominantly present in the neutral-oil fraction of shale oil, aromatic hydrocarbons are predominant in coal oil.

  13. Canada's oil sands : opportunities and challenges to 2015 : an update

    International Nuclear Information System (INIS)

    2006-06-01

    This report updated an energy market assessment compiled and published by the National Energy Board (NEB) in 2004. Major changes resulting from recent developments in the oil sands industry were presented. The report was compiled from a series of informal meetings and discussions with a cross-section of oil sands stakeholders. Influences on recent oil sands development and production growth included market development and pipelines; rising capital and labour costs; operating costs; environmental impact management; high crude oil prices; rising global energy demand; technology innovations; and a more stable investment climate. A comparison of key assumptions between the current analysis and the 2004 report was presented, along with estimates of operating and supply costs for various types of oil sands recovery methods. Potential markets for oil sands production were reviewed. Environmental and socio-economic impacts on the industry included the larger than anticipated water withdrawals from the Athabasca River for mining operations; and uncertainties over land reclamation methods. The industry has also been impacted by a limited supply of skilled workers in Alberta. It was observed that the potential for building cogeneration capacity has decreased since the 2004 report. It was concluded that the oil sands industry will continue to grow rapidly, but the rate of development will depend on the balance that is reached between the opposing forces that affect the oil sands. Natural gas costs, high oil prices, air emissions management issues and water usage will continue to be of concern. 6 tabs., 7 figs

  14. Asian interests in Alberta oil sands

    International Nuclear Information System (INIS)

    Du Plessis, D.; Laureshen, C.

    2004-01-01

    The growing Asian interest in Alberta's oil sands and import opportunities was discussed along with the feasibility of marketing bitumen to Asia. Asia is an obvious new market for Canadian heavy oil and bitumen due to an increasing demand for petroleum products in Japan, Korea, Taiwan and China. This paper examined the following three criteria that will determine the success of any initiative to move Canadian crude oil to Asian-Pacific markets: (1) a sustainable supply from Alberta; a pipeline to transport the crude to a deepwater port on the west coast; and, a guaranteed market at the other end. The basis for Asian interest in Alberta's oil sands is the sustainable secure supply of oil for growing Asian markets; heavy dependence on supplies from the Middle East; the desire to diversify supply sources; and, opportunities to invest in oil sands developments. Examples of Asian (Japan, Korea, Taiwan and China) missions to Alberta were presented along with the challenges of getting products to market with reference to Enbridge's new market access plan, Terasen's staged capacity expansion for heavy crudes and refined products, and sea transport from Prince Rupert. The paper also included graphs depicting world GDP; incremental increase in world primary energy demand by fuel for 2000 to 2020; world oil demand by region; oil demand by region in Asia; oil demand and supply in northeast Asia (Japan, China, Korea) and dependence level on Middle Eastern oil; oil demand and supply in China; China's petroleum production and consumption; refined products market forecast for 2000 to 2020; 2002 crude oil imports to Asia; 2004 refining capacity; product quality comparisons; cost competitive study; and energy policy objectives for China, Japan, Korea and Taiwan. 19 figs

  15. Heavy mineral concentration from oil sand tailings

    Energy Technology Data Exchange (ETDEWEB)

    Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

    2008-07-01

    This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

  16. Oil from biomass corncob tar as a fuel

    International Nuclear Information System (INIS)

    Zhang, Hongmei; Wang, Jun

    2007-01-01

    In this study, biomass corncob tar oil (B-oil I and B-oil II) was extracted and its characteristics were measured. The characterization data show some similarities and differences among B-oil I, B-oil II and the Diesel: flash point. The densities and viscosities are higher than that of Diesel fuel. The solidifying point for B-oil I and B-oil II were lower than that of Diesel. The heating value of B-oil I and B-oil II were about 85.6% and 87.3% of that ordinary Diesel fuel (OD). The distillation temperatures of B-oil I and B-oil II were lower than that of Diesel fuel, with the 50% evaporation point being as much as 10 o C and 4 o C lower and the 90% evaporation point being 10 o C and 2 o C lower, respectively. These evaporation characteristics implied better cold starting and warm up properties of B-oil I and B-oil II than that of Diesel fuel. B-oil I and B-oil II were blended with Diesel in 10% and 20% by volume. Engine tests have been conducted with the aim of obtaining comparative measures of torque, thermal efficiency, specific fuel consumption and emissions such as CO, smoke density and NO to evaluate and compute the behavior of the Diesel engine running on the above mentioned fuels. The reduction in exhaust emissions, together with the increases in torque and thermal efficiency and the reduction in specific fuel consumption made the blends of B-oil I and B-oil II a suitable alternative fuel for Diesel and could help in controlling air pollution

  17. Sustainable use of oil sands for geotechnical construction and road building

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2012-02-01

    Full Text Available Oil sands are natural deposits of bituminous sand materials that are mined and processed for crude oil. They are routinely used in oil sand fields for building temporary and sometimes permanent roads serving mining and hauling activities. Although...

  18. Oil sands market and transportation solutions

    International Nuclear Information System (INIS)

    Sandahl, R.

    2004-01-01

    This presentation outlined the immense potential of the western Canadian oil sands reserves. Recoverable reserves have been estimated at 180 billion barrels, with production forecasts estimated at 5 million barrels per day by 2030. Resource development is occurring at a time when the world's largest oil importer is increasing supplies through concern for security of supply. The second and third largest oil importers in the world are experiencing economic and energy demand growth. These factors underscore the motivation for rapid growth of the Western Canadian Oil Sands reserves. One of the challenges that must be addressed is to ensure that incremental markets for the increased production are accessed. Another challenge is to ensure adequate infrastructure in terms of pipeline capacity to ensure deliverability of the product. tabs., figs

  19. Athabasca tar sands as a source of crude oil

    Energy Technology Data Exchange (ETDEWEB)

    Montgomery, D S

    1964-01-01

    A general review is presented of the variable nature of the Athabasca bituminous sand resource, and the chemical composition of the bitumen is given at various stages during the refining from raw material to finished products. The research conducted at the Mines Branch, Ottawa, on vapor-phase hydrogenation of coker distillates is described, emphasizing the effect of hydrogen pressure on the rate of catalyst deactivation. The quality of the hydrogenated products is described in general terms and some observations are made on the reasons why large-scale operation is essential if an economical process is to be achieved.

  20. Microbial processes in the Athabasca Oil Sands and their potential applications in microbial enhanced oil recovery.

    Science.gov (United States)

    Harner, N K; Richardson, T L; Thompson, K A; Best, R J; Best, A S; Trevors, J T

    2011-11-01

    The Athabasca Oil Sands are located within the Western Canadian Sedimentary Basin, which covers over 140,200 km(2) of land in Alberta, Canada. The oil sands provide a unique environment for bacteria as a result of the stressors of low water availability and high hydrocarbon concentrations. Understanding the mechanisms bacteria use to tolerate these stresses may aid in our understanding of how hydrocarbon degradation has occurred over geological time, and how these processes and related tolerance mechanisms may be used in biotechnology applications such as microbial enhanced oil recovery (MEOR). The majority of research has focused on microbiology processes in oil reservoirs and oilfields; as such there is a paucity of information specific to oil sands. By studying microbial processes in oil sands there is the potential to use microbes in MEOR applications. This article reviews the microbiology of the Athabasca Oil Sands and the mechanisms bacteria use to tolerate low water and high hydrocarbon availability in oil reservoirs and oilfields, and potential applications in MEOR.

  1. The oil sands: A new energy vision for Canada

    International Nuclear Information System (INIS)

    1995-01-01

    Canada's oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada's trade balance. 1 ill

  2. Oil sands: Strategies for future development - An overview

    International Nuclear Information System (INIS)

    Yildirim, E.

    1995-01-01

    The Alberta Chamber of Resources developed a Task Force in 1993 to promote oil sands development, and to identify and publicize the social and economic benefits of oil sands operations. Formation, mission of the National Task Force, impediments and opportunities for development were summarized. Attributes of oil sands, benefits of their development, impediments to development, strategic development and potential growth scenarios were discussed. Cooperation between government and industry was deemed essential. Recommendations included development of a bitumen pipeline network, provision of incentives to encourage development, encouragement of risk and reward sharing between bitumen producers and up graders, and diversification of products and by-products. 7 figs., 12 refs

  3. Thermal remediation of tar-contaminated soil and oil-contaminated gravel

    International Nuclear Information System (INIS)

    Anthony, E.J.; Wang, J.

    2005-01-01

    High temperature treatments are commonly considered for the decontamination of soil as they have the advantages of reliability, high capacity, and effective destruction of hazardous materials with reduced long-term liability. This paper examined the remediation of soil contaminated by coal tar as well as gravel contaminated by oil. Pilot plant studies were conducted using 2 representative incineration technologies: rotary kiln and fluidized bed. The coal tar contaminated soil had accumulated over a few decades at a calcination plant in western Canada. The soil was sticky and could not be handled by conventional feeding and combustion systems. Crushed lignite was mixed with the soil as an auxiliary fuel and to reduce stickiness. A pilot plant furnace was used to evaluate the potential of decontamination in a rotary calciner. An analysis of both a modelling study and the test results showed that complete decontamination could be achieved in the targeted calciner. The results suggested that energy recovery was also possible, which could in turn make the remediation process more cost-effective. Decontamination of oil-contaminated gravel was conducted with a pilot plant fluidized bed combustor to study the feasibility of using incineration technology in the remediation of gravel and debris contaminated by oil spills. Results indicated that the gravel was decontaminated with acceptable emission performance. It was concluded that the study will be valuable to the application of commercial incineration processes for the remediation of polluted soils. It was observed that the weathering of the oiled gravel lowered the rate of decontamination. A small amount of salt water resulted in lowered decontamination rates, which may be an important factor for situations involving the remediation of shoreline gravel contaminated by oil. 24 refs., 6 tabs., 7 figs

  4. Preliminary fiscal evaluation of Alberta oil sands terms

    International Nuclear Information System (INIS)

    Van Meurs, P.

    2007-01-01

    The cost of oil sands projects varies significantly. While costs have escalated considerably over the past few years, oil prices have gone significantly higher. This report provided an economic evaluation of the current fiscal terms applicable to Alberta oil sands. The analysis was done to evaluate the profitability of oil sand projects to investors under current conditions based on the generic royalty regime based on bitumen values. The objective of the royalty review was to determine whether Albertans received a fair share from their oil and gas resources. It discussed the wide variety of oil sands projects in Alberta using five case studies as examples. Cases involving steam assisted gravity drainage (SAGD) operations were assessed for both the Athabasca Mine and Cold Lake. The report provided a discussion of the economic assumptions including economic cases as well as production, costs and price data. It then provided the preliminary results of the economic-fiscal evaluation from the investor perspective including profitability indicators; international comparisons; internal rate of return; and net present value. The government perspective was also discussed with reference to attractiveness indicators; royalties as a percentage of bitumen values; and non-discounted and discounted government take. A royalty and tax feature analysis was also provided. Several issues for possible further review were also presented. tabs

  5. Saskatchewan's place in the Canadian oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Schramm, L.L. [Saskatchewan Research Council, Saskatoon, SK (Canada); Kramers, J.W. [Owl Ventures Inc., Edmonton, AB (Canada); Isaacs, E.E. [Alberta Energy Research Inst., Calgary, AB (Canada)

    2009-07-01

    This paper provided a detailed description of the oil sands geology and physical properties and highlighted some of the novel recovery technologies that are being developed for shallow in-situ reservoirs in Alberta and Saskatchewan. Canada's oil sands are well known around the world, with Alberta's mined and in-situ oil sands reservoirs being well developed with mature commercial technologies. Shallow in-situ oil sands located in both Saskatchewan and Alberta will be the next frontier in Canadian petroleum development. Shallow reservoirs will need to be developed with new environmentally sound in-situ technologies that will reduce the use of steam and fresh water, and also reduce greenhouse gas emissions. Research and development programs are currently underway to develop and demonstrate such new technologies. It was concluded that innovation has been the key to developing the immense and complex technology oil contained in Canada's heavy oil reservoirs and also in its shallow and deep in-situ oil sands reservoirs. Promising technologies include the solvent vapour extraction and hybrid thermal solvent extraction processes that are being developed and demonstrated in large-scale three-dimensional scaled physical models and associated numerical simulation models. Electrical heating and gravity stable combustion are other examples of technologies that could play a significant role in developing these resources. 88 refs., 3 tabs., 8 figs.

  6. Evaluating the oil sands reclamation process: Assessing policy capacity and stakeholder access for government and non-governmental organizations operating in Alberta's oil sands

    Science.gov (United States)

    Patterson, Tyler

    By employing interpretive policy analysis this thesis aims to assess, measure, and explain policy capacity for government and non-government organizations involved in reclaiming Alberta's oil sands. Using this type of analysis to assess policy capacity is a novel approach for understanding reclamation policy; and therefore, this research will provide a unique contribution to the literature surrounding reclamation policy. The oil sands region in northeast Alberta, Canada is an area of interest for a few reasons; primarily because of the vast reserves of bitumen and the environmental cost associated with developing this resource. An increase in global oil demand has established incentive for industry to seek out and develop new reserves. Alberta's oil sands are one of the largest remaining reserves in the world, and there is significant interest in increasing production in this region. Furthermore, tensions in several oil exporting nations in the Middle East remain unresolved, and this has garnered additional support for a supply side solution to North American oil demands. This solution relies upon the development of reserves in both the United States and Canada. These compounding factors have contributed to the increased development in the oil sands of northeastern Alberta. Essentially, a rapid expansion of oil sands operations is ongoing, and is the source of significant disturbance across the region. This disturbance, and the promises of reclamation, is a source of contentious debates amongst stakeholders and continues to be highly visible in the media. If oil sands operations are to retain their social license to operate, it is critical that reclamation efforts be effective. One concern non-governmental organizations (NGOs) expressed criticizes the current monitoring and enforcement of regulatory programs in the oil sands. Alberta's NGOs have suggested the data made available to them originates from industrial sources, and is generally unchecked by government

  7. Value of Canadian oil sands... to the United States

    International Nuclear Information System (INIS)

    Pugliaresi, Lucian

    2011-01-01

    Since the beginning of the recession in late 2007, the American economy has been subject to great change, affecting the way energy is produced and consumed. The structure of oil imports and exports has changed significantly and U.S. imports are now primarily from Canada. The current study shows how and why the U.S. has become dependent on imports of oil from the Canadian oil sands. Oil from Canadian oil sands is transported to different Petroleum Administration for Defense Districts (PADD) via the Keystone pipeline. As imports from Canada increased, the U.S. refinery sector was restructured. Small refineries were closed while larger refineries were expanded and investment was made to increase their processing capacity. The increased import and processing of oil from the Canadian oil sands led to an advantageous decrease in oil prices. If the Keystone XL project were to be approved, the pipeline would increase the area with access to the means of transporting oil, allowing the increasing demand for oil to be met and, potentially, stabilizing world oil prices.

  8. Oil sands development update

    International Nuclear Information System (INIS)

    1999-01-01

    A detailed review and update of oil sands development in Alberta are provided covering every aspect of the production and economic aspects of the industry. It is pointed out that at present oil sands account for 28 per cent of Canadian crude oil production, expected to reach 50 per cent by 2005. Based on recent announcements, a total of 26 billion dollars worth of projects are in progress or planned; 20 billion dollars worth of this development is in the Athabasca area, the remainder in Cold Lake and other areas. The current update envisages up to 1,800,000 barrels per day by 2008, creating 47,000 new jobs and total government revenues through direct and indirect taxes of 118 billion dollars. Provinces other than Alberta also benefit from these development, since 60 per cent of all employment and income created by oil sands production is in other parts of Canada. Up to 60 per cent of the expansion is for goods and services and of this, 50 to 55 per cent will be purchased from Canadian sources. The remaining 40 per cent of the new investment is for engineering and construction of which 95 per cent is Canadian content. Aboriginal workforce by common consent of existing operators matches regional representation (about 13 per cent), and new developers are expected to match these standards. Planned or ongoing development in environmental protection through improved technologies and optimization, energy efficiency and improved tailings management, and active support of flexibility mechanisms such as emission credits trading, joint implementation and carbon sinks are very high on the industry's agenda. The importance of offsets are discussed extensively along with key considerations for international negotiations, as well as further research of other options such as sequestration, environmentally benign disposal of waste, and enhanced voluntary action

  9. The oil sands: A new energy vision for Canada

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    Canada`s oil sands deposits were considered to offer huge potential for wealth generation and enduring social benefits. This report showed that putting in action the plan developed by the National Task Force on Oil Sands Strategies would help unlock this potential and realize the benefits; the forecast called for a doubling or tripling of oil sands production over the next 25 years. The plan should also predicted an increase in investments in oil sands since the fiscal regime would be stable and the product would be in increasing demand. New capital investment should generate significant environmental, social and economic benefits. The real outcome would be increased national prosperity, since further growth in investment would translate into thousands of skilled jobs across Canada, expansion of government revenues, and improvements to Canada`s trade balance. 1 ill.

  10. Supercritical solvent extraction of oil sand bitumen

    Science.gov (United States)

    Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

    2017-08-01

    The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

  11. Rheology of oil sands slurries

    Energy Technology Data Exchange (ETDEWEB)

    Chow, R.; Zhou, J. [Alberta Research Council, Edmonton, AB (Canada). Mineral Oil Sands Unit; Wallace, D. [Dean Wallace Consulting Inc., Beaumont, AB (Canada)

    2006-07-01

    This study focused on integrating rheology and colloid science to improve recovery of bitumen in surface mined oil sands. Factors that influence recovery, such as conditions of particle interaction, solids concentration and shear rate, were reviewed. In an effort to understand the rheological behaviour of clay-in-water suspensions, an elaborate procedure was developed to separate an inter-bedded clay layer from a site at Albian Sands Energy Inc. The variables were water chemistry, solids concentration, and shear rate. The research study was conducted at the Alberta Research Council with the support of the CONRAD Extraction Group. A controlled stress rheometer was used to provide the quantitative evaluations of the clay slurry properties. The research results indicate that the viscoelastic properties of the slurry are highly influenced by the shear history of the slurry, solids content, calcium concentration, and sample aging. Shear thinning behaviour was observed in all slurry samples, but the slurry viscosity increased with test time for a given shear rate. In order to classify the slurries, a method was developed to distinguish the gel strength. The slurries were then classified into 3 distinct patterns, including no gel, weak gel and strong gel. The evolution of the experimental protocols were described along with the current stability maps that correlate the domains of the gel strength according to the solids concentration, calcium ion content, and shear rate. It was concluded that the rheological properties of oil sands slurries influence bitumen recovery in commercial surface-mined oil sands operations. tabs., figs.

  12. Canadian oil sands : supply and potential for market growth

    International Nuclear Information System (INIS)

    Crandall, G.

    2004-01-01

    Canadian oil sands recoverable reserves rank second only to Saudi Arabia and present enormous potential, particularly through technological gains. This paper discussed the market potential for oil sands both globally and in North America. It was estimated that oil sands production would eventually surpass declining conventional production, increasing from 42 per cent of Western supply in 2002 to 78 per cent in 2015. Recoverable reserves were an estimated 174 billion barrels, with cumulative production at 4 billion barrels between 1967 to 2003. Statistics of U.S. and Canadian markets for crude oil were presented to the year 2020. A flow chart of oil sands products and market outlets was presented, as well as details of existing and potential markets for Canadian crude oil. Oil sands product dispositions were outlined, with the prediction that Asia may emerge as an incremental market. World crude oil production statistics were presented by type. World residual supply and demand estimates were presented, including details of conversion capacity and requirements for residual processing capacity in refineries and field upgraders. American refinery feedstocks were presented by type, with the identification of an increase in heavy crude runs. It was noted that recent pricing provided a strong incentive to add refining conversion capacity to process heavy oil. An outline of a study completed for the Alberta government and industry was presented, in which upgrading to light synthetic crude was determined as a base case. The value added to process bitumen beyond upgrading was discussed in relation to the upgrading of American refineries to process bitumen blends and synthetic crude. Potential cases for upgrading bitumen were presented, along with a comparison of capital costs. An overall economic comparison of projects was provided. Various measures to maximize markets for oil sands products in Alberta were presented. It was suggested that U.S. markets should absorb more new

  13. Geophysics comes of age in oil sands development

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, P. [WorleyParsons Komex, Calgary, AB (Canada); Birch, R.; Parker, D.; Andrews, B. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

    2008-07-01

    This paper discussed geophysical techniques developed for oil sands exploration and production applications in Alberta's oil sands region. Geophysical methods are playing an important role in mine planning, tailings containment, water supply, and land reclamation activities. Geophysics techniques are used to estimate the volume of muskeg that needs to be stripped and stored for future reclamation activities as well as to site muskeg piles and delineate the thickness of clay Clearwater formations overlying Cretaceous oil-bearing sands. 2-D electrical resistivity mapping is used to map river-connected deep bedrock Pleistocene paleovalleys in the region. Geophysical studies are also used to investigate the interiors of dikes and berms as well as to monitor salt migration within tailings piles. Sonic and density logs are used to create synthetic seismograms for mapping the Devonian surface in the region. The new applications included the calculation of bitumen saturation from surface sands and shales; muskeg thickness mapping; and non-intrusive monitoring of leachate plumes. Geophysical techniques included 2-D electrical resistivity imaging; transient electromagnetic (EM) technologies; ground penetrating radar; and high-resolution seismic reflections. Polarization, surface nuclear magnetic resonance and push-probe sensing techniques were also discussed. Techniques were discussed in relation to Alberta's Athabasca oil sands deposits. 4 refs.

  14. Water management challenges and perspective for surface oil sands operations in North Eastern Alberta

    International Nuclear Information System (INIS)

    MacKinnon, M.

    2009-01-01

    Oil sands waters has many sources, such as raw water inputs (import water and hydrologic waters); oil sands ore water such as formation water; and oil sands process-affected water (OSPW) such as produced water and released water from tailings. This presentation demonstrated the importance of water to oil sands operations and indicated how oil sands processing affects water quality. Water imports to meet oil sands needs is a topic of particular interest. Other topics that were presented included water properties changing during oil sands operations; tailings management and the effects on water quality; oil sands tailings and water management and the impact on water quality of the region; how oil sands processing affected water quality; and current tailings approach and proposed new tailings methods and the effects on water composition. Post extraction changes in OSPW and the potential impacts of engineered tailings were also discussed. It was concluded that water treatment options must meet water management objectives. figs.

  15. The eye of the beholder : oil sands calamity or golden opportunity?

    International Nuclear Information System (INIS)

    McColl, D.

    2009-02-01

    Alberta's oil sands deposits are one of the largest hydrocarbon deposits in the world, and the oil sands industry has become a significant driving force in the Canadian economy. However, development in the region has slowed as a result of the recent economic downturn. This paper discussed the future of the oil sands industry, and argued that excess global oil supplies will need to be consumed before the industry fully recovers. Increased liquidity and higher oil prices are also required in order to help the industry recover. Oil sands data were aggregated and classified according to their various stages of development. Projections of bitumen production were based on the summation of all announced projects. Assumptions were adjusted to reflect current and likely near-term future outlooks for oil sands development. Results of the study indicated that the pace of development is expected to slow. Current leases will be developed at a slower pace. Prices in excess of $70 will be required for the industry to continue expanding as well as to generate a rate of return that can be reinvested into the Canadian economy. It was concluded that opportunities for current oil sands operators and new project proponents should take advantage of lower prices to source materials and equipment. 3 figs

  16. [Imperial Oil's Cold Lake oil sands operations

    International Nuclear Information System (INIS)

    Dingle, H. B.

    1999-01-01

    Imperial Oil Limited's Cold Lake oil sands resources, production and operations in Alberta are discussed. Cold Lake is the company's largest single asset and its largest source of crude oil production. In 1998, Cold Lake accounted for just under half of Imperial's total liquid production, averaging more than 135,000 barrels of bitumen a day. Despite the very difficult operating conditions experienced by the oil sands industry in 1998, Imperial Oil's Cold Lake operations generated a positive cash flow and earnings. Just as important, the near and long-term potential of Cold Lake property continues to be strong, even with the tough market conditions today and the foreseeable future. Proved reserves at the end of 1997 were 1.3 billions barrels, equal to about 24 years of current production, but even more important is Imperial's resource base in the Athabasca region, which represents 150 years of production at current rates. Although production forecasts for the near future are are revised downward because of production shut-in due to low prices, the company is confident of its long-term prospects mainly because of existing infrastructure, superior reservoir quality, 30 years worth of operating improvements and established bitumen-blend markets. Details of the company's future Cold Lake development plans are discussed. The need to continue technology development, which has been at the core of the industry's growth in the past and will continue to be the key to the future, are emphasized

  17. Study on the basic properties of Indonesian oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Qing; Jiang, Qian-qian; Bai, Jing-ru; Sun, Jian; Liu, Hong-peng [Northeast Dianli Univ., Jilin (China). Inst. of Energy and Power Engineering

    2013-07-01

    The basic properties of three Indonesian oil sands have been investigated. The results show that since the high content of volatile, heating value and oil yield, Indonesian oil sands could be combusted for power generation and retorting for oil refining. Moreover, oil sand ash with the low content of fixed carbon and high content of CaO, could not only be used as solid heat carrier during retorting, but also comprehensively used as construction material. Based on the thermogravimeric analysis (TGA), pyrolysis and combustion behaviors have been identified. As for pyrolysis, 350-520 C could be regarded as the major oil-producing region, the apparent activation energy E is not a constant obtained by distributed activation energy model (DAEM). For combustion, 620-800 C is the high-temperature oxidation (HTO) stage. TG-DTG extrapolation method was applied to determine the combustion characteristics parameters such as ignition temperature, burn-out temperature, combustion stability and combustion reactivity, and finally gave a comparison with those of oil shale and coal.

  18. Alberta's oil sands fiscal system : historical context and system performance

    International Nuclear Information System (INIS)

    2007-01-01

    This report described the fiscal system applied to Alberta's oil sands. It is the first technical report forming part of a series designed to provide information and to invite comment as part of the Government of Alberta's public review of the fiscal system applied to the province's oil and gas resources. Specifically, this report assessed the robustness of Alberta's oil sands fiscal system and assessed how the regime balanced the risks and rewards to both investors and Albertans across a range of expected and probable economic outcomes. The report provided an explanation of the history and context of Alberta's royalty regime and included a case-by-case approach. It also provided a discussion of the oil sands fiscal system description. Next, it described the methodology employed for the analysis of the oil sands fiscal system. It also provided the assumptions for 5 scenario cases and presented the fiscal map approach for assessing project economics and fiscal system performance. Last, summary observations were presented. It was found that the oil sands fiscal system is very flexible for adverse economic conditions and much less so for highly profitable conditions. tabs., figs

  19. North American Oil Sands: History of Development, Prospects for the Future

    National Research Council Canada - National Science Library

    Humphries, Marc

    2008-01-01

    .... Since 2004, when a substantial portion of Canada's oil sands were deemed economic, Canada, with about 175 billion barrels of proved oil sands reserves, has ranked second behind Saudi Arabia in oil reserves...

  20. Sources of atmospheric emissions in the Athabasca oil sands region

    International Nuclear Information System (INIS)

    1996-01-01

    An inventory of emissions for the Athabasca oil sands airshed that can be used as a basis for air quality assessments was presented. This report was prepared for the Suncor Steepbank Mine Environmental Impact Assessment (EIA) and for the Syncrude Aurora Mine EIA. Both Syncrude and Suncor have plans to develop new oil sands leases and to increase their crude oil and bitumen production. Suncor has proposed modifications to reduce SO 2 emissions to the atmosphere and Syncrude will develop additional ambient air quality, sulphur deposition and biomonitoring programs to ensure that environmental quality is not compromised because of atmospheric emissions associated with their operations. Major emission sources are controlled and monitored by regulatory statutes, regulations and guidelines. In this report, the following four types of emission sources were identified and quantified: (1) major industrial sources associated with Suncor's and Syncrude's current oil sands operations, (2) fugitive and area emission sources such as volatilization of hydrocarbons from tanks and tailings ponds, (3) other industrial emission sources in the area, including oil sands and non-oil sands related facilities, and (4) highway and residential emission sources. Emissions associated with mining operations include: SO 2 , NO x , CO, and CO 2 . The overall conclusion was that although there are other smaller sources of emissions that can influence air quality, there is no reason to doubt that Suncor and Syncrude oil sands operations are the major sources of emissions to the atmosphere. 13 refs., 12 tabs., 8 figs

  1. Performance monitoring of electric shovels digging oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Patnayak, S. [Alberta Univ., Edmonton, AB (Canada). Natural Resources Engineering Facility; Tannant, D.D. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering; Parsons, I. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre; Del Valle, V. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

    2005-07-01

    Some of the largest available mining equipment is used for oil sand mining operations. However, the performance of electric cable shovels varies with the diggability characteristics of the ground. In particular, oil sands diggability with cable shovels depends on structural geology, the depositional environment and geotechnical parameters. This paper described some of the key shovel performance indicators such as dig cycle time, digging energy and digging power. In winter, frost penetration can also affect oil sands diggability. The challenge of hard digging in oil sands is often addressed by blasting or ripping, which increases the cost of production and impedes productivity. The shovel performance is also influenced by other parameters such as operator skills, bucket and tooth design and shovel dipper trajectory. This paper demonstrated that hoist and crowd motor voltages and currents are useful in identifying the beginning and end of dig cycles. Performance indicators such as dig cycle time, hoist motor energy and power, and crowd motor energy and power were considered to assess material diggability. It was suggested that hoist power represents the ground diggability better than other performance indicators. 5 refs., 1 tab., 10 figs.

  2. Low-temperature tar from bituminous coal and its further treatment

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, C J

    1950-01-01

    High-temperature carbonization of bituminous coal yields only 3 to 4 percent tar, as compared with 8 to 10 percent or even more for low-temperature carbonization. The yield of phenols is 20 to 30 times as great from the low-temperature tar. Five conditions that must be met by a satisfactory low-temperature carbonization process are listed. The only method that satisfies all of these conditions is the Brennstoff-Technik (BT) process, in which iron retorts with movable walls are used. One disadvantage of most of the other processes is the high-pitch content of the tar. These tars are processed further to a neutral oil and a phenol-containing oil which are good diesel fuels with high-cetane numbers; the neutral oil can be fractionated to give oils of high-, medium-, and low-cetane number. Attempts to fractionate the tar oil by solvents have not proved commercially useful. However, the tar can be diluted with low-temperature light oil and phenols extracted with NaOH solution without distillation. Some difficulty is found, owing to the simultaneous extraction of viscous resins and other products that are readily removed from the phenols by distillation.

  3. Insight conference reports : Western Canada oil sands

    International Nuclear Information System (INIS)

    2005-01-01

    This conference presented issues of concern to the Canadian oil sands industry. Focal points included supply and the potential for market growth as well as opportunities and challenges faced by the industry in the current market. Various projects were discussed, including the Northern Lights and Fort Hill projects. Reserves and resource booking procedures were examined, as well as issues concerning the streamlining of regulatory barriers and various approaches to the Kyoto Protocol and greenhouse gas (GHG) emissions. Oil sands portfolios were reviewed as well as issues concerning the recovery of titanium and zircon, the economics of Steam Assisted Gravity Drainage (SAGD) options and innovations in technology and sub-surface risk assessment for in-situ projects. Transportation initiatives were examined as well as pipeline issues and storage infrastructure development. Issues concerning financing as well as the economic environment of the oil sands industry were also discussed. The conference featured 20 presentations, of which 5 have been catalogued separately for inclusion in this database. tabs, figs

  4. Chemical modification of a bitumen and its non-fuel uses. [Reactions of tar sand asphaltenes in synthesis of non-fuel products

    Energy Technology Data Exchange (ETDEWEB)

    Moschopedis, S.E.; Speight, J.G.

    1974-01-01

    Simple reactions are described whereby tar sand bitumen can be converted to a whole range of materials. Examples are given to illustrate the non-fuel uses of the products. The following reactions of Athabasca asphaltenes are considered: oxidation, halogenation, sulfonation and sulfomethylation, phosphorylation, hydrogenation, reactions with S and O, reactions with metal salts, and miscellaneous chemical conversions. (JGB)

  5. Research investigations in oil shale, tar sand, coal research, advanced exploratory process technology, and advanced fuels research: Volume 1 -- Base program. Final report, October 1986--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    Smith, V.E.

    1994-05-01

    Numerous studies have been conducted in five principal areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. In subsequent years, underground coal gasification was broadened to be coal research, under which several research activities were conducted that related to coal processing. The most significant change occurred in 1989 when the agreement was redefined as a Base Program and a Jointly Sponsored Research Program (JSRP). Investigations were conducted under the Base Program to determine the physical and chemical properties of materials suitable for conversion to liquid and gaseous fuels, to test and evaluate processes and innovative concepts for such conversions, to monitor and determine environmental impacts related to development of commercial-sized operations, and to evaluate methods for mitigation of potential environmental impacts. This report is divided into two volumes: Volume 1 consists of 28 summaries that describe the principal research efforts conducted under the Base Program in five topic areas. Volume 2 describes tasks performed within the JSRP. Research conducted under this agreement has resulted in technology transfer of a variety of energy-related research information. A listing of related publications and presentations is given at the end of each research topic summary. More specific and detailed information is provided in the topical reports referenced in the related publications listings.

  6. A look at one of the world`s largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. [Hagglunds Drives Canada Inc., Vancouver, BC (Canada)

    1999-10-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world`s largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  7. The energy efficiency of oil sands extraction: Energy return ratios from 1970 to 2010

    International Nuclear Information System (INIS)

    Brandt, Adam R.; Englander, Jacob; Bharadwaj, Sharad

    2013-01-01

    It has been argued that the oil sands industry is not energy efficient: comparatively large energy inputs are required per unit of energy output from oil sands operations. Unfortunately, quantitative work to date in this area has suffered from poor data availability and uncertain methods. We apply a new methodology and new dataset to compute ERRs (energy return ratios) for the oil sands industry. We collected monthly oil sands energy consumption and output data from 1970 to 2010. Current oil sands operations have mine mouth NERs (net energy returns) of about 6 GJ output per GJ of energy consumed and point of use energy returns of about 3 GJ/GJ. Long-term trends show oil sands operations becoming significantly more efficient: point of use NER increased from about 1 GJ/GJ in 1970 to 3 GJ/GJ in 2010. These energy returns are lower than those observed in historical conventional oil operations, but low energy returns are not likely to hinder development of oil sands operations due to the large resource in place and the ability for largely self-fueled pathways to return significant amounts of energy to society for every unit of external energy supplied. - Highlights: • Oil sands operations have become significantly more energy efficient over the history of the industry. • Oil sands production is largely fueled with energy from the bitumen resource itself, making external energy returns high. • Oil sands production is still significantly less efficient than conventional oil production

  8. Distilling tar; distillation, destructive

    Energy Technology Data Exchange (ETDEWEB)

    Brash, P; Young, W

    1866-09-17

    The tarry residue, which separates on treating crude shale oil with sulfuric acid, is redistilled, in the manner described in Specification No. 1278, A.D. 1866, together with shale. Previous to the distillation, the acid is neutralized with lime, or may be separated by blowing steam into the tar and adding salt. The purified tar thus obtained is absorbed by ashes, or is mixed with lime or other alkaline matter, or the shale may be mixed with lime and distilled with the tar, which is allowed to flow over and through the shale during the process. The tar obtained in the purification of natural paraffin may be similarly utilized.

  9. The use of stable isotopes to trace oil sands constituents

    International Nuclear Information System (INIS)

    Farwell, A.J.; Nero, V.; Dixon, D.G.

    2002-01-01

    A study was conducted to determine the biological effects of oil sands mining operations on aquatic ecosystems. The study focused on the Athabasca oil sand deposit, the largest of 4 deposits in northern Alberta. In particular, the study examined the cycling of oil sand constituents in Benthic invertebrates collected from test pits at Syncrude Canada Ltd.. The invertebrates were similar in size, but different in the quantity of process-affected water or mature fine tailings containing residual bitumen. Dragonflies and damselflies in particular, showed trends of depletion for the carbon 13 isotope and enrichment in nitrogen 15 isotope in pits where levels of process affected water was high. The depletion of carbon 13 isotope suggests that oil sand constituents assimilate into the benthic food chain. The greatest carbon 13 depletion, which was approximately 27 per cent, was found to be in test pits with high turbidity. This implies that oil sands constituents degrade microbially instead of by photosynthetic production. All benthic invertebrate group demonstrated an incremental enrichment in nitrogen 15 isotope from the control pit to the pit with greatest levels of mature fine tailings

  10. Process for separating and recovering oil from oil-sands, etc

    Energy Technology Data Exchange (ETDEWEB)

    Preller, H

    1921-02-24

    A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil-shale, and coal, according to Patent 400,122, is described. It is characterized in that the mined material falling on account of its weight is exposed to the running hot water in circulation through the wash-chamber and the clarifying chamber arranged separate or built on (circulation) being obtained by pumps or injectors in a regulatable motion.

  11. Oil sand synfuel production using nuclear energy

    International Nuclear Information System (INIS)

    Barnert, H.

    1984-10-01

    The importance of oil sand as a primary energy carrier is illustrated. The oil sand mining project 'synfuel' in Fort McMurray, Alberta, Canada, is described. On the basis of a layout of an In-situ-process different possibilities of introducing nuclear energy to the process are described. This leads to an increase of the product yield, leading finally to a doubling of the energy output compared to the reference layout. The introduction of nuclear energy contributes to the reduction of emissions, in particular to the emission of carbon dioxide in the conversion process. (orig.)

  12. Ecotoxicological impacts of effluents generated by oil sands bitumen extraction and oil sands lixiviation on Pseudokirchneriella subcapitata

    Energy Technology Data Exchange (ETDEWEB)

    Debenest, T., E-mail: tdebenest@yahoo.fr [Environment Canada, Fluvial Ecosystem Research, 105 McGill Street, 7 floor, Montreal, Quebec, H2Y 2E7 (Canada); Turcotte, P. [Environment Canada, Fluvial Ecosystem Research, 105 McGill Street, 7 floor, Montreal, Quebec, H2Y 2E7 (Canada); Gagne, F., E-mail: francois.gagne@ec.gc.ca [Environment Canada, Fluvial Ecosystem Research, 105 McGill Street, 7 floor, Montreal, Quebec, H2Y 2E7 (Canada); Gagnon, C.; Blaise, C. [Environment Canada, Fluvial Ecosystem Research, 105 McGill Street, 7 floor, Montreal, Quebec, H2Y 2E7 (Canada)

    2012-05-15

    The exploitation of Athabasca oil sands deposits in northern Alberta has known an intense development in recent years. This development has raised concern about the ecotoxicological risk of such industrial activities adjacent to the Athabasca River. Indeed, bitumen extraction generated large amounts of oil sands process-affected water (OSPW) which are discharged in tailing ponds in the Athabasca River watershed. This study sought to evaluate and compare the toxicity of OSPW and oil sands lixiviate water (OSLW) with a baseline (oil sands exposed to water; OSW) on a microalgae, Pseudokirchneriella subcapitata, at different concentrations (1.9, 5.5, 12.25, 25 and 37.5%, v/v). Chemical analyses of water-soluble contaminants showed that OSPW and OSLW were enriched in different elements such as vanadium (enrichment factor, EF = 66 and 12, respectively), aluminum (EF = 64 and 15, respectively), iron (EF = 52.5 and 17.1, respectively) and chromium (39 and 10, respectively). The toxicity of OSPW on cells with optimal intracellular esterase activity and chlorophyll autofluorescence (viable cells) (72 h-IC 50% < 1.9%) was 20 times higher than the one of OSW (72 h-IC 50% > 37.5%, v/v). OSLW was 4.4 times less toxic (IC 50% = 8.5%, v/v) than OSPW and 4.5 times more toxic than OSW. The inhibition of viable cell growth was significantly and highly correlated (<-0.7) with the increase of arsenic, beryllium, chromium, copper, lead, molybdenum and vanadium concentrations. The specific photosynthetic responses studied with JIP-test (rapid and polyphasic chlorophyll a fluorescence emission) showed a stimulation of the different functional parameters (efficiency of PSII to absorb energy from photons, size of effective PSII antenna and vitality of photosynthetic apparatus for energy conversion) in cultures exposed to OSPW and OSLW. To our knowledge, our study highlights the first evidence of physiological effects of OSPW and OSLW on microalgae.

  13. Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

    International Nuclear Information System (INIS)

    D'Aquin, G.

    2008-01-01

    This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations

  14. Characterization of napthenic acids in oil sands process-affected waters using fluorescence technology

    International Nuclear Information System (INIS)

    Brown, L.; Alostaz, M.; Ulrich, A.

    2009-01-01

    Process-affected water from oil sands production plants presents a major environmental challenge to oil sands operators due to its toxicity to different organisms as well as its corrosiveness in refinery units. This abstract investigated the use of fluorescence excitation-emission matrices to detect and characterize changes in naphthenic acid in oil sands process-affected waters. Samples from oil sands production plants and storage ponds were tested. The study showed that oil sands naphthenic acids show characteristic fluorescence signatures when excited by ultraviolet light in the range of 260 to 350 mm. The signal was a unique attribute of the naphthenic acid molecule. Changes in the fluorescence signature can be used to determine chemical changes such as degradation or aging. It was concluded that the technology can be used as a non-invasive continuous water quality monitoring tool to increase process control in oil sands processing plants

  15. Tar loads on Omani beaches

    International Nuclear Information System (INIS)

    Badawy, M.I.; Al-Harthy, F.T.

    1991-01-01

    Owing to Oman's geographic position and long coastal line, the coastal areas of Oman are particularly vulnerable to oil pollution from normal tanker operations, illegal discharges, and accidental spills as well as local sources of oil input. UNEP carried out a survey on the coasts of Oman to determine the major sources of oil pollution and concluded that the major shoreline pollution problems in Oman arose from operational discharges of oil from passing vessels traffic. The oil, because of the high sea and air temperatures in the area, was subjected to relatively high rates of evaporation and photo-oxidation and tended to arrive at the coast as heavy petroleum particulate residues (tar balls). The aim of the present study was to measure the loads of tar balls in Omani coastal areas and to identify the source of oil pollutants on beaches

  16. Naphtha evaporation from oil sands tailings ponds

    Energy Technology Data Exchange (ETDEWEB)

    Kasperski, K.; Munoz, V.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre

    2010-07-01

    The environmental impacts of volatile organic compounds (VOCs) from oil sands tailings ponds must be considered when evaluating new oil sands mining and extraction operations. Studies have suggested that only 40 percent of the solvent sent to tailings ponds is available to the environment, while the rest is irreversibly trapped. The recovery of hydrocarbons from oil sands froth process water is low. This PowerPoint presentation discussed a method of distinguishing between water and hydrocarbons at low temperatures. Samples were heated to 246 degrees C at 15 degrees C and held for 10 minutes. Heating was then resumed at 750 degrees C and held for 10 minutes in a pyrolysis phase, then cooled and reheated with an oxygen addition. The method demonstrated that the diluent distribution between the solids and water phases is misinterpreted as diluent that will evaporate, and diluent that will not evaporate. The study concluded by suggesting that the definition of recoverable and unrecoverable hydrocarbon should be re-termed as easily recoverable, and difficult to recover. tabs., figs.

  17. A look at one of the world's largest apron feeder drives - Alberta Oil Sands Project

    Energy Technology Data Exchange (ETDEWEB)

    Persson, O. (Hagglunds Drives Canada Inc., Vancouver, BC (Canada))

    1999-01-01

    Various types of equipment to transport tar sands to processing plants are discussed, with special attention to the advantages of hydraulic direct drives over conventional electro-mechanical drives. A hydraulic direct drive such as the Hagglund Drive has exceptional starting torque capacity due to the high torque capability of the hydraulic motor. As such, it can be particularly useful in applications where shock loads occur with some frequency, or where many starts and stops are needed. Application of the Hagglund drive to power one of the world's largest apron feeders in the Alberta Oil Sands is described as an illustration of the exceptional reliability, productivity and performance of this equipment. It has about one five-hundredth of the inertia of an equivalent high speed drive with gear reducer, a feature which is particularly significant in the case of feeders which are known to suffer much downtime due to chain related problems. These types of drives have also been used to great advantage in the process industries like pulp and paper, chemical, rubber and plastics, recycling and steel. 1 tab., 1 fig.

  18. Oil sands development in a carbon constrained world

    Energy Technology Data Exchange (ETDEWEB)

    McDougall, J. [Alberta Research Council, Devon, AB (Canada)

    2006-07-01

    The challenges facing oilsands development in Alberta were discussed in this PowerPoint presentation. In 2005, 71 per cent of Alberta's export value was derived from energy and mining. The author addressed the issue that resource based economies have rarely succeeded in the long term. He then demonstrated how such economies could capture value from technology. The primary focus was on the goal to develop and adapt greenhouse gas (GHG) transformational technologies that will break the link between hydrocarbon energy use and GHG emissions. The role of oil sands in this endeavour was also discussed. Alberta's oil sands are the world's largest hydrocarbon resource, with 315 b bbls proven reserves, and 2.5 t bbls potential reserves. As an important economic driver for Alberta, oil sands production is expected to grow significantly in the next 2 decades. Since bitumen production is more energy intensive than conventional oil, the industry is faced with the challenge of sustainable development. Concentrated GHG emissions create opportunities to proceed with long-term oil sands development with a sustainable level of GHG emissions, but technology and infrastructure are needed to take advantage of them. Current carbon dioxide (CO{sub 2}) storage projects in Alberta were highlighted. The economic potential of geological storage of CO{sub 2} through acid gas injection or deep disposal was discussed in terms of enhanced oil recovery, enhanced coalbed methane recovery, enhanced gas recovery and cost avoidance of CO{sub 2} per tonne. It was emphasized that a long-term vision and commitment is needed to balance with short term problems solving and longer-term strategic agendas. tabs., figs.

  19. Generation and migration of Bitumen and oil from the oil shale interval of the Eocene Green River formation, Uinta Basin, Utah

    Science.gov (United States)

    Johnson, Ronald C.; Birdwell, Justin E.; Mercier, Tracey J.

    2016-01-01

    The results from the recent U.S. Geological Survey assessment of in-place oil shale resources of the Eocene Green River Formation, based primarily on the Fischer assay method, are applied herein to define areas where the oil shale interval is depleted of some of its petroleum-generating potential along the deep structural trough of the basin and to make: (1) a general estimates of the amount of this depletion, and (2) estimate the total volume of petroleum generated. Oil yields (gallons of oil per ton of rock, GPT) and in-place oil (barrels of oil per acre, BPA) decrease toward the structural trough of the basin, which represents an offshore lacustrine area that is believed to have originally contained greater petroleum-generating potential than is currently indicated by measured Fischer assay oil yields. Although this interval is considered to be largely immature for oil generation based on vitrinite reflectance measurements, the oil shale interval is a likely source for the gilsonite deposits and much of the tar sands in the basin. Early expulsion of petroleum may have occurred due to the very high organic carbon content and oil-prone nature of the Type I kerogen present in Green River oil shale. In order to examine the possible sources and migration pathways for the tar sands and gilsonite deposits, we have created paleogeographic reconstructions of several oil shale zones in the basin as part of this study.

  20. Geophysical mapping of the occurrence of shallow oil sands in ...

    African Journals Online (AJOL)

    Oil sands are known to be an alternate source of energy and of great economic value. To map the occurrence of shallow oil sand deposits in Idiopopo, Okitipupa area in Ondo state southwestern Nigeria, vertical electric sounding (VES) in 11 stations along 3 profiles were carried out using the Schlumberger configuration.

  1. Non-aqueous heavy oil extraction from oil sand

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert, George [National Nuclear Security Administration (United States)

    2011-07-01

    The Kansas City plant operated by Honeywell has a long history of working with DOE NNSA on engineering and manufacturing services supporting national security requirements. The plant has developed a non-aqueous method for heavy oil extraction from oil sands. This method is environmentally friendly as it does not use any external body of water, which would normally be contaminated in the conventional method. It is a 2 phase process consisting of terpene, limonene or alpha pinene, and carbon dioxide. The CO2 and terpene phases are both closed loop systems which minimizes material loss. The limonene and alpha pinene are both naturally derived solvents that come from citrus sources or pine trees respectively. Carbon dioxide is an excellent co-solvent with terpene. There is also a possibility for heat loss recovery during the distillation phase. This process produces clean dry sand. Laboratory tests have concluded that this using non-aqueous liquids process works effectively.

  2. Engaging Canadians: national oil sands dialogues - A background paper

    International Nuclear Information System (INIS)

    Carson, Bruce

    2010-01-01

    It is expected that the world's energy demand will grow significantly between now and the year 2050. Hydrocarbons will have an important role to play in meeting this increasing demand and unconventional sources such as oil sands will become more and more important. The Canadian Association of Petroleum Producers (CAPP) has been engaged in a dialogue process to examine the environmental, economic and social impacts of the oil sands industry and the aim of this background paper is to provide stakeholders with some context. The paper highlights the fact that although the oil sands industry gives rise to environmental issues such as greenhouse gas emissions, air pollutants, land disturbance and water use, the environmental performance of the industry has been improving in recent years thanks to new technologies.

  3. A new era of opportunity for Canada's oil sands

    International Nuclear Information System (INIS)

    1996-06-01

    The enormous potential for wealth that is offered by Canada's oil sands deposits was discussed. Alberta's oil sands contain more recoverable oil than all the reserves of Saudi Arabia - but they have barely been developed. They are a natural resource of sufficient size, scale and competitive advantage to be of great benefit to the economy. The National Oil Sands Task Force has invested billions of dollars in the project and believes that the industry can triple production over the next 25 years. Benefits to Canadians will include an estimated 44,000 new jobs across the country, $97 billion increase in revenue for all levels of government, and $100 billion increase in consumer disposable incomes. In order to realize these socio-economic benefits, some important improvements were recommended to insure industry efficiency and growth. Some of the recommendations included increased investment in science and technology, as a key component of development. 1 tab., 4 figs

  4. Canada's oil sands, opportunities and challenges to 2015 : an energy market assessment

    International Nuclear Information System (INIS)

    2004-05-01

    The National Energy Board monitors the supply of all energy commodities in Canada along with the demand for Canadian energy commodities in domestic and export markets. This report provides an assessment of the current state of the oil sands industry and the potential for growth. It also identifies the major issues and challenges associated with the development of Canada's oil sands, one of the world's largest hydrocarbon resources. Initial production of Canada's oil sands began in 1967. The resource has become more economic to develop in recent years due to higher energy prices and new technologies. The economic potential of Canada's oil sands has been recognized internationally. Canadian oil sands production in 2004 will surpass 160,000 cubic metres per day. By 2015, production is expected to more than double to meet market demands. The challenges facing the industry include higher natural gas prices, capital cost overruns and environmental impacts. The major factors that affect the rate of oil sands development include natural gas supply, energy demand, oil and gas pricing, markets and pipelines, environmental considerations, emerging technologies, geopolitical issues, and labour. This report includes key findings for the following four key components: economic potential and development of the resource base; markets and pipelines; environmental and socio-economic impacts; and, potential spin-off developments in the electricity and petrochemical industries. 26 tabs., 53 figs

  5. Advanced CANDU reactor: an optimized energy source of oil sands application

    International Nuclear Information System (INIS)

    Hopwood, J.M.; Bock, D.; Miller, A.; Kuran, S.; Keil, H.; Fiorino, L.; Duffey, R.; Dunbar, R.B.

    2003-01-01

    Atomic Energy of Canada Limited (AECL) is developing the ACR-700 TM (Advanced CANDU Reactor-700 TM ) to meet customer needs for reduced capital cost, shorter construction schedule, high capacity factor while retaining the benefits of the CANDU experience base. The ACR-700 is based on the concept of CANDU horizontal fuel channels surrounded by heavy water moderator. The major innovation of this design is the use of slightly enriched uranium fuel in a CANFLEX bundle that is cooled by light water. This ensures: higher main steam pressures and temperatures providing higher thermal efficiency; a compact and simpler reactor design with reduced capital costs and shorter construction schedules; and reduced heavy water inventory compared to existing CANDU reactors. ACR-700 is not only a technically advanced and cost effective solution for electricity generating utilities, but also a low-cost, long-life and sustainable steam source for increasing Alberta's Oil Sand production rates. Currently practiced commercial surface mining and extraction of Oil Sand resources has been well established over the last three decades. But a majority of the available resources are somewhat deeper underground require in-situ extraction. Economic removal of such underground resources is now possible through the Steam Assisted Gravity Drainage (SAGD) process developed and proto-type tested in-site. SAGD requires the injection of large quantities of high-pressure steam into horizontal wells to form reduced viscosity bitumen and condensate mixture that is then collected at the surface. This paper describes joint AECL studies with CERI (Canadian Energy Research Institute) for the ACR, supplying both electricity and medium-pressure steam to an oil sands facility. The extensive oil sands deposits in northern Alberta are a very large energy resource. Currently, 30% of Canda's oil production is from the oil sands and this is expected to expand greatly over the coming decade. The bitumen deposits in the

  6. Canada's oil sands: nuclear power in an integrated energy economy

    Energy Technology Data Exchange (ETDEWEB)

    Isaacs, E. [Alberta Energy Research Inst., Alberta (Canada)

    2008-06-15

    At a time of the expansive global growth in energy demand and the peaking of conventional oil, the Canadian Oil Sands have emerged as the largest new reserves to supply oil to world markets. Bitumen production in 2006 averaged 1.25 million barrels per day (an increase of 13% over 2005 and an 88% increase since 2000). If this trend continues Canada will be positioned as one of the world's premier suppliers of oil for many decades to come. The Oil Sands are one of the world's most challenging and complex oil resources. They require considerable amount of energy, water and land area to produce, resulting in contaminated tailings ponds, air emissions of concern and copious greenhouse gas (GHG) emissions. As the need to protect the environment and reduce GHG emissions moves higher on the public agenda Canada's ability to grow the energy supplies from oil sands will be severely tested. This paper focuses on the current and emerging methods and innovations that can be applied to produce these unconventional resources to value-added products with a decreasing impact on the environment. The paper will also describe the benefits and challenges for nuclear energy in the oil sands as a solution to the need for substitutes for natural gas in oil sands production and upgrading and in meeting Canada's GHG emission targets. (author)

  7. Oil-sands giants leaving smaller environmental footprints

    International Nuclear Information System (INIS)

    Stonehouse, D.

    1999-01-01

    Suncor Energy and Syncrude Canada are both investing billions of dollars to increase production at their mining facilities near Fort McMurray, Alberta. The two oil-sand giants will be spending a good portion of their investment (almost $1 billion) to improve their environmental performance. Both companies are focusing on reducing their energy use to cut production costs and to reduce carbon dioxide (CO 2 ) emissions. Currently, oil-sand mining accounts for the largest industrial use of electricity in Alberta. This produces tremendous amounts of greenhouse gases such as CO 2 which has been linked to global warming. By year 2006, all of Syncrude's processing equipment will be replaced by energy-efficient equipment. Shovel/truck/hydrotransport will replace the dragline/bucket-wheel/conveyor system used in the past. New technology designed to improve bitumen recovery and increase upgrading processing yields is also expected to decrease emissions by 5 million tonnes per year. Syncrude will also construct a $60 million gas turbine generator for its Aurora project. Sulphur dioxide (SO 2 ) emissions which cause acid rain, are also on the decline at both Syncrude and Suncor. Suncor will reduce its energy use through the construction of a $315 million cogeneration plant which will generate 220 MV of electricity for its operations, along with waste heat that will be used to separate the heavy oil from the sand. The cogeneration plant will be 45 per cent more efficient that current operations. Both companies have planted millions of trees and shrubs to reclaim nearly 3,000 hectares of land. The tailings from oil-sand mining are currently being captured in settling basins. Both companies have long range plans for dealing with tailings. The first is called water capping which involves layering fresh water over tailing deposits to create a lake. The second is called composite tails, which involves mixing the tailings with gypsum and sand to make them settle faster

  8. Evaluation of lignite tar

    Energy Technology Data Exchange (ETDEWEB)

    Gossedin, A

    1946-01-01

    Tar from the low-temperature (450/sup 0/) carbonization of lignite from Bouches-du-Rhone was hydrogenated in the presence of a catalyst based on MoS/sub 2/ with a 3:1 H:N mixture. Processing (at 470/sup 0/ and 400 atmospheres) for maximum production of gasoline yielded 86 wt % of a product of boiling 55 to 186/sup 0/ and motor octane number 75. An alternative is to hydrogenate with a view to producing solvents and lubricants. For this purpose the tar was separated by distillation (at 20 millimeters, cutting at 220/sup 0/) into two fractions of equal volume. On hydrogenation (at 300/sup 0/ and 400 atmospheres) the light part yields a gasoline H/sub 2/O-soluble cut, a highly aromatic solvent fraction, a heavier cut (280/sup 0/ to 320/sup 0/) suitable as a plasticizer, and a phenol fraction. The heavier part of the tar is hydrogenated (at 380/sup 0/ and 400 atmospheres) to give spindle oil and lubricating oil of medium eta (11.2 centistokes at 98.2/sup 0/), moderate eta index (64), good pour point (-7/sup 0/), and good oxidizing characteristics. The overall yield of products from the two portions is 86.9% (gasoline and solvent 32, light phenols 9.7, spindle oil 14.2, medium lubricating oil 25.7, wax, 5.3%).

  9. Purifying and regenerating hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1931-11-19

    Hydrocarbons are freed from sulfur-containing compounds, colloidal asphaltic bodies and unstable unsaturated substances by treatment with a small amount of dilute sulfuric acid and a salt of a trivalent cation, such as ferric chloride or sulfate. Hydrocarbons specified are petroleum, crude benzol, low temperature tars, shale oil or vapor-phase cracked spirit. Motor spirit or lubricating oil distillates are refined and finally distilled. The acid reagent may be regenerated by filtering through sand or asbestos. Used lubricating oils may be treated similarly and after removal of refining agent, the oil is heated with an adsorbent and decolorizing material and then filtered.

  10. Extraction of tar acids with methanol from low-temperature tar

    Energy Technology Data Exchange (ETDEWEB)

    Funasaka, W; Yokogawa, C; Suga, S

    1948-01-01

    From 20 grams crude middle oil, boiling at 200/sup 0/ to 250/sup 0/, acid content 40%, tar acids were extracted at 20/sup 0/ to 30/sup 0/ with MeOH for comparison with EtOH, NMe/sub 3/, and ethylene glycol. When 80% MeOH is used, the oil extracted amounts to 61%, including 9% acids, if the ratio of crude oil and solvent is kept at 1:2. EtOH is inferior to MeOH. The properties of the crude oil and the purified oil extracted with 80% MeOH are described.

  11. 3D Finite Element Analysis of PWA-Oil Sand Terrain System Interaction

    Directory of Open Access Journals (Sweden)

    Y. Li

    2012-01-01

    Full Text Available A simulator for analyzing the interaction between the oil sand terrain and a pipe wagon articulating (PWA system has been developed in this paper. An elastic-plastic oil sand model was built based on the finite element analysis (FEA method and von Mises yield criterion using the Algor mechanical event simulation (MES software. The three-dimensional (3D distribution of the stress, strain, nodal displacement, and deformed shape of the oil sands was animated at an environmental temperature of 25°C. The 3D behavior of the oil sand terrain was investigated with different loading conditions. The effect of the load and contact area on the stress and nodal displacement was analyzed, respectively. The results indicate that both the max stress and max nodal displacement increase with the load varying from 0 to 3.6+7 N and decrease with the contact area varying from 2 to 10 m2. The method presented in this paper forms the basis for evaluating the bearing capacity of oil sand ground.

  12. From oil sands to transportation fuels, to electricity, to hydrogen

    International Nuclear Information System (INIS)

    Yildirim, E.

    1993-01-01

    The Alberta Chamber of Resources programs and initiatives on oil sands and heavy oil, and strategies for revitalizing oilsands development in Alberta are described. The regional upgrader and satellite production facilities concept, and technology requirements for mineable oil sands by the year 2010 are discussed. Strategic alliances in furtherence of oil sands research and development and the National Task Force on Oil Sands Strategies are described. Changes in requirements for transportation fuels due to stricter regulations and environmental initiatives will cause a trend to lighter fuels with more hydrogen content, less aromatics, nitrogen, sulfur and metals. A preferred refinery configuration will be able to process heavier crudes and synthetic crudes, have no heavy fuel oil product, low sulfur products, low aromatics with high octane, and low operating cost. A regional or central facility that combines the processing capabilities of a bitumen upgrader with the process units of a refinery is preferred. Advantages of this concept are: value addition to the feedstock is maximized; dependence on refineries is eliminated; restriction on synthetic crude oil volumes due to capacity limitations at refineries is eliminated; directly marketable finished products are produced; more stringent quality specifications are satisfied; and the synergies between upgrading and refining improve overall economics of processing. It is recommended that the concept of regional upgraders be adopted for Alberta, strategic alliances be encouraged, incentives for bitumen production be provided, and a bitumen pipeline network be developed. 12 refs

  13. An investigation of the potential for in situ bioremediation of oil sands tailings

    International Nuclear Information System (INIS)

    Herman, D.C.; Costerton, J.W.; Fedorak, P.M.; Mackinnon, M.D.

    1993-01-01

    Oil sand tailings water has been shown to be acutely toxic to aquatic organisms. Naphthenic acids have been shown to be the primary source of this toxicity within oil sand tailings waste. The potential for in-situ bioremediation of oil sand tailings was investigated by determining the ability of indigenous bacteria to biodegrade naphthenic acids. A mixed bacterial culture enriched from oil sand tailings was found to be capable of growth on a commercially available naphthenic acid mixture. When sodium naphthenates (30 mg/l) were added to a minimal salts medium and inoculated with the mixed bacterial culture, gas chromatography revealed that many components of the naphthenic acid mixture were biodegraded within eight days of incubation. The same culture was also tested against the naphthenic acid fraction extracted directly from oil sand tailings. The tailings extract was diluted into the minimal salts medium in sealed flasks and inoculated with the enrichment culture. The production of CO 2 indicated microbial mineralization of components within the oil sands extract. Microtox analysis determined that microbial activity resulted in a reduction in the acute toxicity of the tailings extract. 5 refs., 3 figs

  14. Aromatic oxygen compounds boiling from 180/sup 0/ to 225/sup 0/ from acid oils in low-temperature tar

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, A; Kattwinkel, G

    1950-01-01

    To determine the composition of the Krupp-Lurgi low-temperature coal tar and to develop methods for isolating the various compounds, a quantitative investigation was made of the dry tar acid mixture. The aromatic O compounds boiling up to 225/sup 0/ were secured by fractionation with one of the several columns that are described. Large volumes of tar were fractionated under vacuum in an apparatus with a 10-liter flask, electrically heated, and provided with a fractionating column (packed) with a jacket supplied by recirculated oil, externally heated. Large volumes were fractionated to give sufficient quantities of the O compounds. The method of fractional extraction, not described herein, made the separation of the acid oils by fractional distillation much easier. The aromatic O compounds present in greatest proportion are relatively easily isolated; those present in small quantities and more difficult to separate can be removed as a mixture, which can be hydrogenated directly to solvents. Phenols and cresols are formed in about equal fractions in low-temperature carbonization. Of the various xylenols, the sym-xylenol is present to the greatest extent. O compounds with longer side chains than C/sub 2/ were present only to a very slight extent. At the temperature of formation of these tars, side chains of three or more C atoms formed closed ring compounds (indan derivatives, etc.). Little change appears to occur up to 225/sup 0/ in the fractionation of these acid oils.

  15. [Research on Oil Sands Spectral Characteristics and Oil Content by Remote Sensing Estimation].

    Science.gov (United States)

    You, Jin-feng; Xing, Li-xin; Pan, Jun; Shan, Xuan-long; Liang, Li-heng; Fan, Rui-xue

    2015-04-01

    Visible and near infrared spectroscopy is a proven technology to be widely used in identification and exploration of hydrocarbon energy sources with high spectral resolution for detail diagnostic absorption characteristics of hydrocarbon groups. The most prominent regions for hydrocarbon absorption bands are 1,740-1,780, 2,300-2,340 and 2,340-2,360 nm by the reflectance of oil sands samples. These spectral ranges are dominated by various C-H overlapping overtones and combination bands. Meanwhile, there is relatively weak even or no absorption characteristics in the region from 1,700 to 1,730 nm in the spectra of oil sands samples with low bitumen content. With the increase in oil content, in the spectral range of 1,700-1,730 nm the obvious hydrocarbon absorption begins to appear. The bitumen content is the critical parameter for oil sands reserves estimation. The absorption depth was used to depict the response intensity of the absorption bands controlled by first-order overtones and combinations of the various C-H stretching and bending fundamentals. According to the Pearson and partial correlation relationships of oil content and absorption depth dominated by hydrocarbon groups in 1,740-1,780, 2,300-2,340 and 2,340-2,360 nm wavelength range, the scheme of association mode was established between the intensity of spectral response and bitumen content, and then unary linear regression(ULR) and partial least squares regression (PLSR) methods were employed to model the equation between absorption depth attributed to various C-H bond and bitumen content. There were two calibration equations in which ULR method was employed to model the relationship between absorption depth near 2,350 nm region and bitumen content and PLSR method was developed to model the relationship between absorption depth of 1,758, 2,310, 2,350 nm regions and oil content. It turned out that the calibration models had good predictive ability and high robustness and they could provide the scientific

  16. Geophysical applications for oil sand mine tailings management

    Energy Technology Data Exchange (ETDEWEB)

    Parker, D.; Bauman, P. [WorleyParsons, Calgary, AB (Canada)

    2009-07-01

    Geophysical techniques are applied throughout a mine's life cycle to facilitate siting, constructing and monitoring of tailings dumps and ponds. This presentation described 3 case studies from the Athabasca region in northeast Alberta that demonstrated some of the concerns associated with oil sand mine tailings, and the information that geophysical surveys can provide. The objectives of these studies were to determine the lateral and depth extents of elevated conductivities of soil and groundwater that have high salt concentration from the tailings sand pore fluid. Due to high chloride concentrations within the tailings material, salt within the root zone may affect vegetation. A terrain conductivity survey was designed to map the lateral extents of salinity impact, while an electrical resistivity tomography (ERT) survey was used to delineate the tailings sand leachate at depth. The proper management of oil sand tailings facilities is vital to the life cycle of a mine. It was concluded that geophysical techniques can be instrumental in managing several engineering and environmental challenges, from Pleistocene channel mapping, to tailings pond settling characteristics, to reclaiming tailings sands. 1 ref., 7 figs.

  17. Tailings dewatering in the oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Longo, S.; Labelle, M. [Golder Paste Technology, Sudbury, ON (Canada); Wislesky, I. [Golder Associates Ltd., Calgary, AB (Canada)

    2010-07-01

    Alberta's Directive 074 was established to reduce fluid tailings produced during oil sands extraction processes. This PowerPoint presentation examined some of the dewatering strategies available for oil sands operators and provided recommendations for implementing a dewatering plan. Sites must be evaluated in order to determine their chemistry, mineralogy, and the total quantity of material to be handled. The availability of potential additives must also be considered. Process technologies must be selected in relation to the operator's depositional strategy. Each site will require its own unique dewatering and depositional strategy. Dewatering technologies include thickening; in-line flocculation; centrifuge; co-mingling; and various new technologies such as electro-osmosis. Laboratory testing programs include index tests, primary stream thickening, and mini-pilot plant testing. The performance of various testing formats was evaluated. Thickening and depositional techniques were reviewed. tabs., figs.

  18. Process for separating and recovering oil from oil-sands, etc

    Energy Technology Data Exchange (ETDEWEB)

    Preller, H

    1920-07-14

    A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil shale, and coal is characterized in that the material to be separated feeds, by a self-acting feeding arrangement, to a system with slowly rotating drums alternating in different directions and thereby it is exposed to the action of hot water running opposite to the rotation, direction of the drum, with addition of extraction-medium, so that the light material is washed out and rises to the top. It is carried off, while the heavy material sinks to the bottom and, by bucket-conveyor is removed.

  19. Class III Mid-Term Project, "Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies"

    Energy Technology Data Exchange (ETDEWEB)

    Scott Hara

    2007-03-31

    The overall objective of this project was to increase heavy oil reserves in slope and basin clastic (SBC) reservoirs through the application of advanced reservoir characterization and thermal production technologies. The project involved improving thermal recovery techniques in the Tar Zone of Fault Blocks II-A and V (Tar II-A and Tar V) of the Wilmington Field in Los Angeles County, near Long Beach, California. A primary objective has been to transfer technology that can be applied in other heavy oil formations of the Wilmington Field and other SBC reservoirs, including those under waterflood. The first budget period addressed several producibility problems in the Tar II-A and Tar V thermal recovery operations that are common in SBC reservoirs. A few of the advanced technologies developed include a three-dimensional (3-D) deterministic geologic model, a 3-D deterministic thermal reservoir simulation model to aid in reservoir management and subsequent post-steamflood development work, and a detailed study on the geochemical interactions between the steam and the formation rocks and fluids. State of the art operational work included drilling and performing a pilot steam injection and production project via four new horizontal wells (2 producers and 2 injectors), implementing a hot water alternating steam (WAS) drive pilot in the existing steamflood area to improve thermal efficiency, installing a 2400-foot insulated, subsurface harbor channel crossing to supply steam to an island location, testing a novel alkaline steam completion technique to control well sanding problems, and starting on an advanced reservoir management system through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring, and evaluation. The second budget period phase (BP2) continued to implement state-of-the-art operational work to optimize thermal recovery processes, improve well drilling and completion practices, and evaluate the

  20. Proceedings of the 2. international oil sands tailings conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    The tailings produced by oil sands extraction processes pose significant threats to the surrounding environment in addition to releasing greenhouse gases (GHGs) into the atmosphere. Recent directives have been established to reduce the amount of tailings produced at oil sands operations, and to ensure that tailings ponds are reclaimed in the most effective manner. This conference provided a forum for researchers and industry experts to discuss issues related to the management and reclamation of oil sands tailings. New technologies for dewatering tailings ponds were presented, and methods of analyzing the chemical properties of tailings were reviewed. The conference was divided into the following 7 sessions: (1) tailings properties, (2) tailings dewatering, (3) new concepts, (4) water and chemistry, (5) soft tailings stabilization and reclamation, (6) water treatment, and (7) new concepts 2. The conference featured 44 presentations, all of which have been catalogued separately for inclusion in this database. tabs., figs.

  1. Field observations of artificial sand and oil agglomerates

    Science.gov (United States)

    Dalyander, Patricia (Soupy); Long, Joseph W.; Plant, Nathaniel G.; McLaughlin, Molly R.; Mickey, Rangley C.

    2015-01-01

    Oil that comes into the surf zone following spills, such as occurred during the 2010 Deepwater Horizon (DWH) blowout, can mix with local sediment to form heavier-than-water sand and oil agglomerates (SOAs), at times in the form of mats a few centimeters thick and tens of meters long. Smaller agglomerates that form in situ or pieces that break off of larger mats, sometimes referred to as surface residual balls (SRBs), range in size from sand-sized grains to patty-shaped pieces several centimeters (cm) in diameter. These mobile SOAs can cause beach oiling for extended periods following the spill, on the scale of years as in the case of DWH. Limited research, including a prior effort by the U.S. Geological Survey (USGS) investigating SOA mobility, alongshore transport, and seafloor interaction using numerical model output, focused on the physical dynamics of SOAs. To address this data gap, we constructed artificial sand and oil agglomerates (aSOAs) with sand and paraffin wax to mimic the size and density of genuine SOAs. These aSOAs were deployed in the nearshore off the coast of St. Petersburg, Florida, during a field experiment to investigate their movement and seafloor interaction. This report presents the methodology for constructing aSOAs and describes the field experiment. Data acquired during the field campaign, including videos and images of aSOA movement in the nearshore (1.5-meter and 0.5-meter water depth) and in the swash zone, are also presented in this report.

  2. Laboratory observations of artificial sand and oil agglomerates

    Science.gov (United States)

    Jenkins, Robert L.; Dalyander, P. Soupy; Penko, Allison; Long, Joseph W.

    2018-04-27

    Sand and oil agglomerates (SOAs) form when weathered oil reaches the surf zone and combines with suspended sediments. The presence of large SOAs in the form of thick mats (up to 10 centimeters [cm] in height and up to 10 square meters [m2] in area) and smaller SOAs, sometimes referred to as surface residual balls (SRBs), may lead to the re-oiling of beaches previously affected by an oil spill. A limited number of numerical modeling and field studies exist on the transport and dynamics of centimeter-scale SOAs and their interaction with the sea floor. Numerical models used to study SOAs have relied on shear-stress formulations to predict incipient motion. However, uncertainty exists as to the accuracy of applying these formulations, originally developed for sand grains in a uniformly sorted sediment bed, to larger, nonspherical SOAs. In the current effort, artificial sand and oil agglomerates (aSOAs) created with the size, density, and shape characteristics of SOAs were studied in a small-oscillatory flow tunnel. These experiments expanded the available data on SOA motion and interaction with the sea floor and were used to examine the applicability of shear-stress formulations to predict SOA mobility. Data collected during these two sets of experiments, including photographs, video, and flow velocity, are presented in this report, along with an analysis of shear-stress-based formulations for incipient motion. The results showed that shear-stress thresholds for typical quartz sand predicted the incipient motion of aSOAs with 0.5–1.0-cm diameters, but were inaccurate for aSOAs with larger diameters (>2.5 cm). This finding implies that modified parameterizations of incipient motion may be necessary under certain combinations of aSOA characteristics and environmental conditions.

  3. Study on trace and rare earth elements in Indonesian oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Jing-ru; Wang, Qing; Liu, Hong-peng; Bai, Zhang [Northeast Dianli Univ., Jilin (China). Engineering Research Centre

    2013-07-01

    Major, trace elements and rare earth and mineral composition of the oil sand samples (ST1, ST2, ST3) and the oil sand retorting residue (semi-coke: SC1, SC2, SC3) from Indonesian were determined by XFS, ICP-MS and XRD methods. The trace elements content in oil sand is pretty much the same thing in Earth's Clarke value. The trace element is abundantly in earth's Clarke, in oil sand yet, for Ti, Mn, Ba, Sr, but these elements are lower enrichment. However, the Cr (EF = 16.8) and Mo (EF = 11.8) are ''enrichment'' in ST1; the Ni (EF =10.5), Se (EF = 17.5), Sr (EF = 28.7), Mo (EF = 106.5), Sc (EF = 12.8) and U (EF = 43.2) are ''enrichment'' in ST2; the Se (EF = 12.6), Sr (EF = 18.4), Mo (EF = 47.5), and U (EF = 27.8) are ''enrichment'' in ST3. Calculations show that trace elements in sime-coke have lower evaporation rate during Fischer Assay. Trace elements in raw oil sand are so stable that trace elements can't move easily to other pyrolysis product but enrich to sime-coke. After retorting, more elements are EF > 10, such as B, V, Ni, As, Se, Sr, Mo, Hg, Cs and U. It is essential to take the pollution produced by trace elements in sime-coke during the sime-coke utilization into consideration. The REEs content had a high correlation with the ash in oil sand. The REE is closely related to terrigenous elastic rocks.

  4. Review of four major environmental effects monitoring programs in the oil sands region

    International Nuclear Information System (INIS)

    Lott, E.O.; Jones, R.K.

    2010-10-01

    The lack of knowledge on current environmental effects monitoring programs for the mineable oil sands region generates a low public confidence in environment health monitoring and reporting programs for the oil sands operations. In 2010, the Oil Sands Research and Information Network (OSRIN) supervised a study reviewing the major environmental effects monitoring programs that are underway in the Regional Municipality of Wood Buffalo. Four main environmental effects monitoring and reporting organizations existing in the oil sands area were engaged to describe their programs through this study: Alberta Biodiversity Monitoring Institute (ABMI), Cumulative Environmental Management Association (CEMA), Regional Aquatic Monitoring Program (RAMP), Wood Buffalo Environmental Association (WBEA). These different organizations have specific roles in providing information, data and understanding of ecosystem effects. A one page visual summary of environmental effects monitoring in the oil sands area resulted from the information received from these organizations and detailed fact sheets were presented for each one of the programs. The report of this study also presents seven other environmental monitoring initiatives or organizations such as Alberta Environment and Environment Canada environmental effects monitoring program. The main observation that emerged from the review was the lack of detailed understanding shown by the stakeholders regarding the monitoring activities performed in the oil sands area. There is a lack of communication of the different programs that are conducted in the region. The study also pointed out that no efforts were put in cross-linking the various programs to be assured that every concerns related to environmental effects associated with oil sands operations were addressed. A better understanding of environmental effects and an improvement in public confidence in the data and its interpretation would probably be observed with the establishment of a

  5. Mining aspects of hard to access oil sands deposits

    Energy Technology Data Exchange (ETDEWEB)

    Stephenson, G.; Wright, D.; Lukacs, Z. [Norwest Corp., Calgary, AB (Canada)

    2006-07-01

    While a variety of oil sands mining technologies have been explored since the 1960s, the oil sands industry has generally favoured truck and shovel mining as a proven, low-cost mining solution. However, surface mining economics are affected by the price of bitumen, haul distances, tailings storage and geotechnical constraints. Maintenance, labour and the cost of replacing tires and ground engaging tools also have a significant impact on the economics of surface mining. Large volumes of water are used in surface mining, and remediation of surface mined areas can take hundreds of years. Damage to machinery is common as oil sands are abrasive and adhere to equipment. This presentation examined recent technologies developed to improve the economics of surface mining. Various extraction and tailings technologies were reviewed. Issues concerning the integration of mining and extraction processes were discussed. Various monitoring tools were evaluated. A review of new underground mining options included outlines of: longwall mining; sub-level caving; tunnel boring; and room and pillar extraction techniques. A generalized regional geology was presented. It was concluded that the oil sands surfacing mining industry should concentrate on near-term research needs to improve the performance and economics of proven technologies. Screening studies should also be conducted to determine the focus for the development of underground technologies. refs., tabs., figs.

  6. Dewatering Behaviour of Fine Oil Sands Tailings : An Experimental Study

    NARCIS (Netherlands)

    Yao, Y.

    2016-01-01

    Oil sands tailings are a warm aqueous suspension of sand, silt, clay, residual bitumen and naphtha. The tailings are hydraulically transported and stored in tailing ponds where they segregate, with the sand settling from suspension forming beaches and the remaining tailings flowing to the middle of

  7. Literature search on the environmental impacts of tar sands operations

    International Nuclear Information System (INIS)

    Birkholz, D.; Prendergast, S.

    1990-09-01

    An extensive review is presented of the literature on the chemistry and biological impacts of current and potential effluents and discharges from oil sands plants on the Athabasca River. The pollutant compounds of interest included polycyclic aromatic hydrocarbons, methyl homologues and metabolites, polycyclic aromatic sulfur heterocycles, polycyclic aromatic nitrogen heterocycles, and naphthenic acids. Topics of interest include chemical methods for identifying and quantitating the above compounds and their metabolites, their sources and release rates, their toxicity to native fish of the Athabasca system, and their degradation in the natural environment. 376 refs., 4 figs., 26 tabs

  8. A Canadian perspective on the supply costs, production and economic impacts from oil sands development

    International Nuclear Information System (INIS)

    McColl, D.; Masri, M.

    2008-01-01

    This article provided a synopsis of oil sands research recently conducted at the Canadian Energy Research Institute (CERI). The production profiles and capital expenditures that CERI has projected for oil sands projects were explored along with the macroeconomic benefits associated with oil sands development. In addition to rising capital and operating costs, bitumen producers are challenged by labour shortages and environmental concerns. However, CERI warrants continued growth in production from the oil sands industry, given the current high price state of the global oil market and security of supply concerns from oil importing countries. This article also provided background information and analysis to assess the implications of future development. The projected growth in the oil sands industry creates demands for infrastructure, housing, health care, education, and business services. The economic impacts were measured at the local, provincial, national and global levels in terms of changes in gross domestic product; changes in employment; and, changes in government revenues. It was concluded that with continued investment and development, Alberta's oil sands resource is expected to continue to produce oil for decades, and would eventually achieve 6 MMbpd production. 8 refs., 3 tabs., 10 figs

  9. Process of extracting oil from stones and sands. [heating below cracking temperature and above boiling point of oil

    Energy Technology Data Exchange (ETDEWEB)

    Bergfeld, K

    1935-03-09

    A process of extracting oil from stones or sands bearing oils is characterized by the stones and sands being heated in a suitable furnace to a temperature below that of cracking and preferably slightly higher than the boiling-point of the oils. The oily vapors are removed from the treating chamber by means of flushing gas.

  10. Extraction of low-temperature tar by various alcohols

    Energy Technology Data Exchange (ETDEWEB)

    Hara, N; Osawa, M; Azuma, H

    1948-01-01

    MeOH was the most effective of the alcohols tested (MeOH to pentanol) in extracting acid components from low-temperature tar. The optimum concentrations of MeOH were 70 to 80% for 1 extraction and 70 to 75% for repeated or continuous extractions when the solvent-tar ratio was 1:1. By 2 to 3 extractions neutral oil could be separated in about 90% yield including > 3% acidic oil.

  11. The Other Major 2010 Oil Spill: Oil weathering after the Kalamazoo River Dilbit Spill

    Science.gov (United States)

    Swarthout, B.; Reddy, C. M.; Nelson, R. K.; Hamilton, S. K.; Aeppli, C.; Valentine, D. L.; Fundaun, S. E.; Oliveira, A. H.

    2016-02-01

    Diluted bitumen (dilbit) from the oil sands (tar sands) of western Canada is increasingly being transported to US markets. North America's largest inland oil spill and the first major oil sands spill in a freshwater environment occurred in 2010, when at least 843,000 gallons leaked from a pipeline into the Kalamazoo River of southwest Michigan. Cleanup of this oil was unusually difficult and protracted, lasting through 2014 and costing over a billion dollars, largely because a substantial fraction of the oil became submersed and deposited in slack water areas over 60 km of river channel, reservoirs, and floodplain backwaters. To investigate the fate of the spilled dilbit from the 2010 Kalamazoo River release, black rings, presumably oil residues, on the bark of dead trees were collected in 2015. These residues were deposited on the trees during high flood levels that have not been observed since the spill and represent an opportunity to constrain weathering processes excluding dissolution. This material contained a major non-GC amenable fraction of 90-95%, presumably oxygenated hydrocarbons. The GC amenable portion was consistent with laboratory weathered dilbit. We used a variety of analytical tools to characterize the dilbit residues, as well as to identify dilbit weathering processes that occurred since the spill.

  12. The splitting of P and NG and oil sands rights: an historical perspective

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, F. D. [Alberta Department of Energy, Edmonton, AB (Canada)

    1997-12-31

    Changes in the Mines and Minerals Act of Alberta are described to illustrate the evolution of the priorities and thinking over time that led to the present administration of oil sands and natural gas as separate minerals. Natural gas was first excluded from the definition of bituminous sands in 1955. The definition of bituminous sands was changed in 1957 to include natural gas once again. In a further change in 1978, both petroleum and natural gas were excluded from the definition of oil sands. More changes followed in 1984, when petroleum was added back into the definition, leaving natural gas as the only mineral excluded from the definition of oil sands. The 1984 change was triggered by changes in the Oil Sands Conservation Act. It is the current definition, which includes `sands and other rock materials containing crude bitumen, and any other mineral substances, other than natural gas, in association with that crude bitumen`. It was a resource conservation issue in the past, and it is a conservation issue today, although much influenced by changes in technology and increased knowledge and understanding of the relevant factors. 2 tabs.

  13. Tropospheric Emission Spectrometer (TES) Satellite Validations of Ammonia, Methanol, Formic Acid, and Carbon Monoxide over the Canadian Oil Sands

    Data.gov (United States)

    U.S. Environmental Protection Agency — The URLs link to the data archive of the Troposphere Emission Spectrometer (TES) retrievals. These include the transects included in the Canadian Tar Sands study. A...

  14. Proceedings of the Canadian Heavy Oil Association Conference : Heavy oil, the business of evolution

    International Nuclear Information System (INIS)

    2003-01-01

    gas industry to exchange knowledge about fueling options, emerging technologies for resource recovery, and markets and logistics. Most of the papers were presented in Power-Point format with several viewgraphs depicting processes used mostly to recover bitumen from the tar sand and oil sand deposits in Western Canada. The enhanced recovery methods ranged from chemical recovery and thermal recovery methods such as steam assisted gravity drainage (SAGD) and toe-to-heel air injection (THAI). Separation processes and sorbent recovery methods were also discussed. The conference featured 11 presentations, of which 5 were indexed separately for inclusion in this database. refs., tabs., figs

  15. Streamflow measurements in the oil sands region of northeastern Alberta[General Conference

    Energy Technology Data Exchange (ETDEWEB)

    Ashiq, M.; Ade, F. [Golder Associates Ltd., Calgary, AB (Canada). Water Resources Engineering Group

    2006-07-01

    Oil sands mining in the muskeg terrain of north-eastern Alberta will result in changes to the natural landscape, including changes to the morphology of receiving streams. The streams in the oil sands region are fed by constricted flows through the muskeg terrain. The roughness of the stream is attributed to sporadic cobbles and boulders, in-stream vegetation, over hanging vegetation and large quantities of wooden debris from beaver activities. This paper discussed stream roughness features in the oil sands region and compared the velocity profiles in these streams to the normal channel velocity profile. The study also included a comparison of computed discharges based on a simple method and a detailed method. The sources of errors in velocity measurements were then discussed. It was noted that before any oil sand mining project is approved, flows in receiving streams are monitored as part of the Environment Impact Assessment (EIA). The flows are then monitored again after project approval as part of project approval conditions.

  16. Determination of phenol in tar

    Energy Technology Data Exchange (ETDEWEB)

    Dierichs, A; Heinichen, G

    1955-01-01

    During low-temperature carbonization of lignite, the phenols and other oxygenated compounds appear both in the aqueous-process liquor and in the tar. Measurements of these oxygenated components resulting from low-temperature carbonization may serve as a parameter for the classification of lignites. However, such measurements are complicated by the instability of the tar and the complex nature of some of the acidic substances. Difficulties with the previous methods of analysis are reviewed. The present method outlines separation of aqueous-process liquor from lignite tar in a Fischer retort, followed by determination of phenols and fatty acids in the tar phase. The jacketed tar receiver is washed with 300 milliliter xylol and treated with aqueous caustic washes. Neutral oils are separated from the aqueous alkali solution. It is then extracted with ether and finally acidified with HCl. Solids are filtered off, and phenols and fatty acids are separated by Na/sub 2/CO/sub 3/ solution.

  17. Sustainable use of oil sands for geotechnical construction and road building

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2012-02-01

    Full Text Available of the three oil sand samples. Oil Sand ID w [%] wb [%] D10 D30 D50 D60 Cu Cc SE-09 1.4 8.5 0.07 0.12 0.17 0.19 2.9 1.17 SE-14 3.2 13.3 0.08 0.14 0.18 0.21 2.8 1.24 AU-14 2.2 14.5 0.09 0.17 0.22 0.27 3.0 1.19 w = water content; wb = bitumen content; Di... = grain size (mm) corresponding to i-percent passing by mass; Cu = coefficient of uniformity; Cc = coefficient of curvature. Sample Preparation The oil sand samples were prepared for the laboratory testing program using an Industrial Process...

  18. Groundwater Discharges to Rivers in the Western Canadian Oil Sands Region

    Science.gov (United States)

    Ellis, J.; Jasechko, S.

    2016-12-01

    Groundwater discharges into rivers impacts the movement and fate of nutrients and contaminants in the environment. Understanding groundwater-surface water interactions is especially important in the western Canadian oil sands, where groundwater contamination risks are elevated and baseline water chemistry data is lacking, leading to substantial uncertainties about anthropogenic influences on local river quality. High salinity groundwater springs sourced from deep aquifers, comprised of Pleistocene-aged glacial meltwater, are known to discharge into many rivers in the oil sands. Understanding connections between deep aquifers and surficial waterways is important in order to determine natural inputs into these rivers and to assess the potential for injected wastewater or oil extraction fluids to enter surface waters. While these springs have been identified, their spatial distribution along rivers has not been fully characterized. Here we present river chemistry data collected along a number of major river corridors in the Canadian oil sands region. We show that saline groundwater springs vary spatially along the course of these rivers and tend to be concentrated where the rivers incise Devonian- or Cretaceous-aged aquifers along an evaporite dissolution front. Our results suggest that water sourced from Devonian aquifers may travel through bitumen-bearing Cretaceous units and discharge into local rivers, implying a strong groundwater-surface water connection in specialized locations. These findings indicate that oil sands process-affected waters that are injected at depth have the potential to move through these aquifers and reach the rivers at the surface at some time in the future. Groundwater-surface water interactions remain key to understanding the risks oil sands activities pose to aquatic ecosystems and downstream communities.

  19. Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

    Energy Technology Data Exchange (ETDEWEB)

    D' Aquin, G. [Con-Sul Inc., Bigfork, MT (United States)

    2008-07-01

    This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations.

  20. Distillation of tar and tar fractions in the presence of surface-active coke

    Energy Technology Data Exchange (ETDEWEB)

    Jaeppelt, A; Klaus, J

    1943-01-01

    The tar obtained by low-temperature carbonization of Upper Silesian gas coke and fractions from this tar were distilled in the presence of different grades of coke dust with varying surface activity; the coke had been activated by steam in the course of its production by low-temperature carbonization. The surface activity of the coke dusts was measured by determining the heat of wetting with C/sub 6/H/sub 6/. Tar and coke dust, both anhydrous, were mixed in a kneading machine in such proportions that the capillaries of the dust were saturated and enough ''externally'' bound tar was present to permit briquetting. The briquets were distilled without cracking and with steam as heating medium. The yield and quality of the distillate depended on the magnitude of the internal surface of the coke dust used; a mixture of a very active coke from brown coal and tar yielded a distillate with Conradson carbon residue of 1.34 percent, asphalt content 6.1 percent and eta/sub 20/ 5.4/sup 0/ E. as compared with C residue of 10.95 percent, asphalt content 33.5 percent and eta/sub 20/ 123.6/sup 0/ E. of the distillate obtained in the absence of surface-active coke. Even higher-boiling fractions can be improved by this treatment, although it is preferable to use oils with an initial boiling point below 300/sup 0/. The ratio of oil to adsorbent is not critical, but better results were obtained with higher percentages of added coke dust. The process in its present form is not suited for the conversion of crude creosote to useful phenols.

  1. Oil sands development and its impact on atmospheric wet deposition of air pollutants to the Athabasca Oil Sands Region, Alberta, Canada

    International Nuclear Information System (INIS)

    Lynam, Mary M.; Dvonch, J. Timothy; Barres, James A.; Morishita, Masako; Legge, Allan; Percy, Kevin

    2015-01-01

    Characterization of air pollutant deposition resulting from Athabasca oil sands development is necessary to assess risk to humans and the environment. To investigate this we collected event-based wet deposition during a pilot study in 2010–2012 at the AMS 6 site 30 km from the nearest upgrading facility in Fort McMurray, AB, Canada. Sulfate, nitrate and ammonium deposition was (kg/ha) 1.96, 1.60 and 1.03, respectively. Trace element pollutant deposition ranged from 2 × 10"−"5 - 0.79 and exhibited the trend Hg < Se < As < Cd < Pb < Cu < Zn < S. Crustal element deposition ranged from 1.4 × 10"−"4 – 0.46 and had the trend: La < Ce < Sr < Mn < Al < Fe < Mg. S, Se and Hg demonstrated highest median enrichment factors (130–2020) suggesting emissions from oil sands development, urban activities and forest fires were deposited. High deposition of the elements Sr, Mn, Fe and Mg which are tracers for soil and crustal dust implies land-clearing, mining and hauling emissions greatly impacted surrounding human settlements and ecosystems. - Highlights: • Atmospheric event wet deposition was collected during a 21 month pilot study. • Major ion, anthropogenic and crustal element wet deposition was characterized. • Low precipitation depths attenuated major ion and anthropogenic element deposition. • Oil sands development, urban activities and forest fires contributed to deposition. - In the vicinity of oil sands, monitoring revealed that wet deposition of major ions (SO_4"2"−, NO_3"-, NH_4"+) was highest followed by S and Mg, the latter is a tracer for soil/crustal dust.

  2. BIOTIGER, A NATURAL MICROBIAL PRODUCT FOR ENHANCED HYDROCARBON RECOVERY FROM OIL SANDS.

    Energy Technology Data Exchange (ETDEWEB)

    Brigmon, R; Topher Berry, T; Whitney Jones, W; Charles Milliken, C

    2008-05-27

    BioTiger{trademark} is a unique microbial consortia that resulted from over 8 years of extensive microbiology screening and characterization of samples collected from a century-old Polish waste lagoon. BioTiger{trademark} shows rapid and complete degradation of aliphatic and aromatic hydrocarbons, produces novel surfactants, is tolerant of both chemical and metal toxicity and shows good activity at temperature and pH extremes. Although originally developed and used by the U.S. Department of Energy for bioremediation of oil-contaminated soils, recent efforts have proven that BioTiger{trademark} can also be used to increase hydrocarbon recovery from oil sands. This enhanced ex situ oil recovery process utilizes BioTiger{trademark} to optimize bitumen separation. A floatation test protocol with oil sands from Ft. McMurray, Canada was used for the BioTiger{trademark} evaluation. A comparison of hot water extraction/floatation test of the oil sands performed with BioTiger{trademark} demonstrated a 50% improvement in separation as measured by gravimetric analysis in 4 h and a five-fold increase at 25 hr. Since BioTiger{trademark} performs well at high temperatures and process engineering can enhance and sustain metabolic activity, it can be applied to enhance recovery of hydrocarbons from oil sands or other complex recalcitrant matrices.

  3. Oil sands tailings preliminary ecological risk assessment

    International Nuclear Information System (INIS)

    1994-01-01

    Chemical data collected from various oil sands soil-tailings mixtures were used to determine the ecological risk that such tailings would pose to terrestrial wildlife at the surface of a reclaimed site. A methodology that could be used to evaluate the risks posed by various reclamation options (for dry land only) was proposed. Risks associated with other reclamation options, such as wet landscapes or deeper in-pit disposal, were not evaluated. Ten constituents (eight organic and two inorganic) were found to pose a threat to terrestrial biota. The relative contribution of different exposure pathways (water and food ingestion, incidental soil ingestion, inhalation) were studied by probabilistic models. Some physical and chemical reclamation alternatives which involve incorporating oil sands tailings in the landscape to produce a surface that could sustain a productive ecosystem, were described. 53 refs., 15 tabs., 3 figs

  4. Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

    International Nuclear Information System (INIS)

    Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.S.R.

    2013-01-01

    Highlights: ► This is first fingerprinting study in India on identification of source of tar balls. ► Tar balls were formed from tanker-wash spills and they resemble floating tar ball. ► δ 13 C values of Bombay High crude oil and the present tar balls do not match. ► Compound specific stable carbon isotope analysis confirmed the source of tar balls. ► Source is confirmed as the South East Asian Crude Oil and not the Bombay High crude. -- Abstract: Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ 13 C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source

  5. Investing for the future : Athabasca Oil Sands Trust 1998 annual report

    International Nuclear Information System (INIS)

    1999-01-01

    The Athabasca Oil Sand Trust was created in 1995 when a subsidiary of the Trust, Athabasca Oil Sands Investment Inc., acquired Alberta's 11.74 per cent working interest in the Syncrude Project, which is a joint venture involved in the mining and upgrading of bitumen from the Athabasca oil sands. The Trust is a closed-end investment trust which was created to provide an opportunity for direct public investment in Syncrude and oil sands development in northern Alberta. Syncrude, produced a record 76.7 million barrels of Syncrude Sweet Blend (SSB), and shipped its one billionth barrel on April 16, 1998. Another key achievement in 1998 was the investment the Syncrude Joint Venture Partners of almost half a billion dollars to maintain Syncrude's operations and pursue the Business Plan growth targets outlined in last year's report. By aggressively pursuing this capital investment program despite the current low oil prices, the Syncrude Joint Venture Partners expect to double SSB production to 155 million barrels per year by 2007. The Athabasca Trust's share of these capital expenditures to fuel the projected growth in production is about $ 70 million this year and the next. The report provides operating statistics on production, financial highlights and consolidated balance sheets for 1998, including operating expenditures, capital expenditures, and the usual notes to the consolidated financial statement. 10 tabs., 2 figs

  6. Oil sands development contributes polycyclic aromatic compounds to the Athabasca River and its tributaries

    Science.gov (United States)

    Kelly, Erin N.; Short, Jeffrey W.; Schindler, David W.; Hodson, Peter V.; Ma, Mingsheng; Kwan, Alvin K.; Fortin, Barbra L.

    2009-01-01

    For over a decade, the contribution of oil sands mining and processing to the pollution of the Athabasca River has been controversial. We show that the oil sands development is a greater source of contamination than previously realized. In 2008, within 50 km of oil sands upgrading facilities, the loading to the snowpack of airborne particulates was 11,400 T over 4 months and included 391 kg of polycyclic aromatic compounds (PAC), equivalent to 600 T of bitumen, while 168 kg of dissolved PAC was also deposited. Dissolved PAC concentrations in tributaries to the Athabasca increased from 0.009 μg/L upstream of oil sands development to 0.023 μg/L in winter and to 0.202 μg/L in summer downstream. In the Athabasca, dissolved PAC concentrations were mostly snow, dissolved PAC concentrations were up to 4.8 μg/L, thus, spring snowmelt and washout during rain events are important unknowns. These results indicate that major changes are needed to the way that environmental impacts of oil sands development are monitored and managed. PMID:19995964

  7. Macro-economic benefits of an expanded oil sands industry

    International Nuclear Information System (INIS)

    1995-01-01

    Probable impact of benefits of expanded oil sands development on employment and government revenues were analyzed. Investment in proposed oil sands facilities was forecast to create about 1 million person-years of direct and indirect employment. Forty percent of employment gains would be created in Alberta, with remaining positions mostly in Ontario and Quebec. Government taxes, royalties, reduced debts interest costs and revenues to municipalities, hospitals and pension plans would increase by $97 billion (1994 dollars) between 1995 and 2025. Additional benefits would include increases in average Canadian disposable incomes, substitution of imported with domestic oil, and expansion of gross domestic product in Alberta by 5%. Some variation may be expected because of accuracy of assumptions that were made in the analysis, but the character of the results were not expected to change

  8. Examination of oil sands projects : gasification, CO{sub 2} emissions and supply costs

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, K. [Energy Resources Conservation Board, Calgary, AB (Canada)

    2008-10-15

    Non-conventional resources such as Alberta's oil sands are experiencing increased global interest because of the decline in global conventional oil and natural gas reserves. Bitumen extraction and upgrading is an energy intensive process. This paper provided a general discussion of Alberta's oil sands reserves, production and energy requirements. The paper discussed the application of different technologies to the oil sands, and in particular, the use of gasification as a method to produce bitumen-derived synthesis gas. Two oil sands projects currently under construction and implementing gasification technology were briefly described. The paper also provided a comparison of emission intensities from projects that employ gasification leading to a forecast of carbon dioxide equivalent emissions from the oil sands. The impact of Alberta's legislation and the federal framework on greenhouse gas emissions were also examined. Last, the paper discussed a supply cost methodology to compare an integrated extraction and upgrading project using gasification versus a similar project using a conventional steam methane reforming process (SMR). It was concluded that after comparing carbon dioxide emission intensities across different types of projects, the type of project that would be most heavily impacted by greenhouse gas emissions penalties was an in-situ extraction with an upgrading project that employed gasification technology. 36 refs., 5 tabs., 12 figs., 1 appendix.

  9. Natural attenuation of aged tar-oil in soils: A case study from a former gas production site

    Science.gov (United States)

    Ivanov, Pavel; Eickhorst, Thilo; Wehrer, Markus; Georgiadis, Anna; Rennert, Thilo; Eusterhues, Karin; Totsche, Kai Uwe

    2017-04-01

    Contamination of soils with tar oil occurred on many industrial sites in Europe. The main source of such contamination has been former manufactured gas plants (MGP). As many of them were destroyed during the World War II or abandoned in the second half of the XXth century, the contamination is depleted in volatile and degradable hydrocarbons (HC) but enriched in the heavy oil fractions due to aging processes. We studied a small tar-oil spill in a former MGP reservoir basin. The tar-oil had a total petroleum hydrocarbon (TPH) content of 245 mg/g. At the margin of the spill, vegetation has started to overgrow and intensively root the tar-oil layer. This zone comprised the uppermost 5-7 cm of our profile and contained 28 mg/g of TPH (A-layer)- The layer below the root zone (7-15 cm) was the most contaminated, with 90 mg/g TPH (B-layer). The layer underneath (15-22 cm) had smaller concentrations of 16 mg/g TPH (C-layer). Further down in the profile (D-layer) we found only slightly higher TPH content than in the control samples (1,4 mg/g vs 0,6 mg/g). The polycyclic aromatic hydrocarbons analysis showed the same distribution throughout all layers with highest contents of the PAHs with 4-6 condensed aromatic rings. Direct cell count and extraction of microbial biomass showed that the highly contaminated soil layers A and B had 2-3 times more bacteria than the control soils. CARD-FISH analysis revealed that in samples from layers A and B Archaea were more abundant (12% opposing to 6-7% in control soil). Analysis of bacteria (tested for Alpha-, Beta-, Gamma- and Epsilonproteobacteria and Actinobacteria) showed the dominance of Alphaproteobacteria in the layer A and C both beneath and above the most contaminated layer B. The primers covered the whole microbial consortia in these two layers, leaving almost no unidentified cells. In the most contaminated layer B Alphaproteobacteria amounted only to 20% of the microbial consortium, and almost 40% of the cells remained

  10. Enabling technologies for oil sands development

    International Nuclear Information System (INIS)

    Bailey, R.T.

    1998-01-01

    A review of oil sands production and expansion possibilities in Alberta were presented. The enabling technologies for oil sands projects include mining (bucketwheels, draglines, trucks, shovels conveyors, slurry hydrotransport); extraction (conditioning tumblers, pipelines, tanks, hot water, caustic, cold water, frothers); froth cleaning (centrifuges, solvent treatment); tailings (tailings ponds, consolidated tailings); and upgrading (coking, hydrotreating for SCO, hydrocracking and multiple products). The enabling technologies for in situ production include cyclic steam stimulation for vertical wells, steam assisted gravity drainage (SAGD) for dual horizontal wells, and cold production with wormholes. This paper described the recovery potentials of each of these processes. It also discussed the role of government and industry in research and cooperative research involving both the private and public sectors. Examples of each of these were described such as SAGD, the OSLO cold water extraction process, The consolidated tailings (CT) project, the low energy extraction process (slurry production, hydrotransport, pipeline conditioning and warm water extraction), and research in fine tailings, to demonstrate that although objectives may differ, government and industry research objectives are complementary

  11. Oil sands from Sao Paulo State, Brazil and La Brea de Chumpi, Peru: a geologic perspective

    Energy Technology Data Exchange (ETDEWEB)

    Kramers, John W [Alberta Research Council, Edmonton, AB (Canada); Santos, Paulo R. dos [Instituto de Pesquisas Tecnologicas (IPT), Sao Paulo, SP (Brazil); Gianello, Pedro T [Petroleos del Peru, Lima (Peru)

    1987-12-31

    This work describes two `non-conventional` oil sands occurrences in Peru and Brazil. The study of such occurrences has pointed out the fact that oil sands are found in widely varying geological situations and that not all oil sands have origins similar to the supergiant `conventional` deposits in Canada and Venezuela. 3 refs., 9 figs.

  12. Are PAHS the Right Metric for Assessing Toxicity Related to Oils, Tars, Creosote and Similar Contaminants in Sediments?

    Science.gov (United States)

    Oils, tars, and other non-aqueous phase hydrocarbon liquids (NAPLs) are common sources of contamination in aquatic sediments, and the toxicity of such contamination has generally been attributed to component chemicals, particularly PAHs. While there is no doubt PAHs can be toxic ...

  13. Alberta's economic development of the Athabasca oil sands

    Science.gov (United States)

    Steinmann, Michael

    This dissertation examines the 61-year evolution of public policies pertaining to development of Alberta's non-conventional source of crude oil. The Athabasca oil sands contain an estimated 1.5 trillion barrels and provide for a safe continental supply. The Provincial Government first sponsored this undertaking in 1943. The period from then to 1971 was one of a transition from a wheat economy to a natural-resource economic base. A stable government emerged and was able to negotiate viable development policies. A second period, 1971 to 1986, was marked by unstable world conditions that afforded the Alberta government the ability to set terms of development with multi-national oil firms. A 50% profit-sharing plan was implemented, and basic 1973 terms lasted until 1996. However, 1986 was a critical year because the Organization of Petroleum Exporting Countries (OPEC) reduced prices, causing the Alberta economy to lapse into recession. During a third period, 1986 to 1996, the Alberta Government was unable to adapt quickly to world conditions. A new leadership structure in 1996 made major changes to create ongoing fiscal and development policies. That history provides answers to two primary research questions: How do public policies affect the behaviors of the modern corporation and visa versa? What are the implications for development theory? Two sources of information were used for this study. First, it was possible to review the Premier's files located in the Provincial Archives. Materials from various government libraries were also examined. Some 7,000 documents were used to show the evolution of government policymaking. Second, interviews with leaders of oil companies and federal research facilities were important. Findings support the thesis that, to facilitate oil sands development, government and the private sector have closely collaborated. In particular, revenue policies have allowed for effective R&D organization. Relying on intensive technological

  14. Long vigil in Athabasca oil sands culminates in rapid expansion plans

    Energy Technology Data Exchange (ETDEWEB)

    1974-05-01

    Great Canadian Oil Sands Ltd. needs to earn $40 million or more per year to get a reasonable return on the investment, vice president and general manager R.D. Humphreys told delegates at the Petroleum Accountants Society of W. Canada annual conference at Jasper Park Lodge. The conference then was ''the Alberta Oil Sands.'' Sun Oil Co. has taken no return yet, but has paid off the loans and taken shares in return so it owns nearly all the equity capital. The operation is not really breaking even at present, but should improve because GCOS is getting the full effect of the oil price increase under the original royalty agreement with the Alberta government. It is hoped that this will enable the company to recoup an accumulated deficit of more than $90 million. Money is the biggest problem for the current expansion designed to raise production to the authorized 65,000 bpd. Manpower is second and delivery of materials third. There is a lead time of 15 to 18 mo. on critical materials. Over the long term, tailings disposal is the greatest single problem facing all oil sands operators.

  15. Determination of oxygen, nitrogen, and silicon in Nigerian fossil fuels by 14 MeV neutron activation analysis

    International Nuclear Information System (INIS)

    Hannan, M.A.; Oluwole, A.F.; Kehinde, L.O.; Borisade, A.B.

    2003-01-01

    Classification, assessment, and utilization of coal and crude oil extracts are enhanced by analysis of their oxygen content. Values of oxygen obtained 'by difference' from chemical analysis have proved inaccurate. The oxygen, nitrogen, and silicon content of Nigerian coal samples, crude oils, bitumen extracts, and tar sand samples were measured directly using instrumental fast neutron activation analysis (FNAA). The total oxygen in the coal ranges from 5.20% to 23.3%, in the oil and extracts from 0.14% to 1.08%, and in the tar sands from 38% to 47%. The nitrogen content in the coal ranges from 0.54% to 1.35%, in the crude oil and bitumen extracts from ≤ 0.014% to 0.490%, and in the tar sands from 0.082% to 0.611%. The silicon content in the coal ranges from 1.50% to 8.86%; in the oil and the bitumen extracts it is <1%, and in the tar sands between 25.1% and 37.5%. The results show that Nigerian coals are mostly sub-bituminous. However, one of the samples showed bituminous properties as evidenced by the dry ash-free (daf) percent of carbon obtained. This same sample indicated a higher ash content resulting in a comparatively high percentage of silicon. In oils and tar sands from various locations, a comparison of elements is made. (author)

  16. Flash hydropyrolysis of bituminous coal . III. Research on flash hydropyrolysis tar

    Energy Technology Data Exchange (ETDEWEB)

    Dong, M.; Zhu, Z.; He, Y.; Ding, N.; Tang, L. [East China University of Science and Technology, Shanghai (China)

    2000-02-01

    Tar sample obtained by flash hydropyrolysis (FHP) from Dongshen coal at high pressure entrained reactor was investigated. An effect of flash hydropyrolysis temperature on the main components in tar was studied and the quality of the tar was compared with high temperature coke oven tar. The results showed that: the yields of liquid hydrocarbon in FHP tar were more than 15%, which is twofold of that in coke oven tar; the FHP tar has high oil fraction and low pitch; high phenol components and pure condensed polycyclic aromatic hydrocarbon, and low aliphatic hydrocarbon. The components of the FHP tar were simpler than that of high temperature coke oven tar. Therefore, FHP has improved the quantity and quality of tar. 11 refs., 3 figs., 5 tabs.

  17. Process water treatment in Canada's oil sands industry : 1 : target pollutants and treatment objectives

    International Nuclear Information System (INIS)

    Allen, E.W.

    2008-01-01

    The continuous recycling of tailings pond water in the oil sands industry has contributed to an overall decline in water quality used for bitumen recovery, general water consumption, and remedial activities. This paper reviewed process water quality and toxicity data from 2 long-term oil sands operations. The aim of the study was to determine potential roles for water treatment and provide benchmarks for the selection of candidate water treatment technologies in the oil sands region of Alberta. An overview of the oil sands industry was provided as well as details of bitumen recovery processes. The study examined target pollutants and exceedances identified in environmental and industrial water quality guidelines. The study demonstrated that the salinity of tailings pond water increased at a rate of 75 mg per litre per year between 1980 and 2001. Increases in hardness, chloride, ammonia, and sulphates were also noted. Naphthenic acids released during bitumen extraction activities were determined as the primary cause of tailings pond water toxicity. A summary of recent studies on experimental reclamation ponds and treatment wetlands in the oil sands region was included. 19 refs., 4 tabs., 11 figs

  18. Oil sands naphthenic acids: a review of properties, measurement, and treatment.

    Science.gov (United States)

    Brown, Lisa D; Ulrich, Ania C

    2015-05-01

    The Alberta oil sands contain one of the world's largest reserves of oil - over 169 billion barrels of bitumen are economically recoverable with current extraction technologies. Surface mining and subsequent hot water extraction of bitumen from the ore generates about nine cubic meters of raw tailings per cubic meter of oil. Oil sands facilities are required to operate under a policy of zero water discharge, resulting in ponds containing more than one billion cubic meters of tailings, a mixture of sand, fines and process-affected water. Process-affected water contains numerous organic compounds, including naphthenic acids (NAs), which have been identified as the primary source of acute toxicity of process-affected water. Developments in analytical techniques, aerobic biodegradability, and treatment via chemical oxidation (ozone) of NAs are reviewed. The field continues to be challenged by the lack of a cost-effective, accurate analytical technique for NAs or an understanding of all the organic constituents in process-affected water that may be contributing to observed toxicity and thus requiring treatment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Value of NMR logging for heavy oil characterization

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S.; Chen, J.; Georgi, D. [Baker Hughes, Calgary, AB (Canada); Sun, B. [Chevron Energy Technology Co., Calgary, AB (Canada)

    2008-07-01

    Non-conventional, heavy oil fields are becoming increasingly important to the security of energy supplies and are becoming economically profitable to produce. Heavy oil reservoirs are difficult to evaluate since they are typically shallow and the connate waters are very fresh. Other heavy oil reservoirs are oil-wet where the resistivities are not indicative of saturation. Nuclear magnetic resonance (NMR) detects molecular level interactions. As such, it responds distinctively to different hydrocarbon molecules, thereby opening a new avenue for constituent analysis. This feature makes NMR a more powerful technique than bulk oil density or viscosity measurements for characterizing oils, and is the basis for detecting gas in heavy oil fields. NMR logging, which measures fluid in pore space directly, is capable of separating oil from water. It is possible to discern movable from bound water by analyzing NMR logs. The oil viscosity can be also quantified from NMR logs, NMR relaxation time and diffusivity estimates. The unique challenges for heavy oil reservoir characterization for the NMR technique were discussed with reference to the extra-fast decay of the NMR signal in response to extra-heavy oil/tars, and the lack of sensitivity in measuring very slow diffusion of heavy oil molecules. This paper presented various methods for analyzing heavy oil reservoirs in different viscosity ranges. Heavy oil fields in Venezuela, Kazakhstan, Canada, Alaska and the Middle East were analyzed using different data interpretation approaches based on the reservoir formation characteristics and the heavy oil type. NMR direct fluid typing was adequate for clean sands and carbonate reservoirs while integrated approaches were used to interpret extra heavy oils and tars. It was concluded that NMR logs can provide quantitative measures for heavy oil saturation, identify sweet spots or tar streaks, and quantify heavy oil viscosity within reasonable accuracy. 14 refs., 16 figs.

  20. Microbial communities involved in methane production from hydrocarbons in oil sands tailings.

    Science.gov (United States)

    Siddique, Tariq; Penner, Tara; Klassen, Jonathan; Nesbø, Camilla; Foght, Julia M

    2012-09-04

    Microbial metabolism of residual hydrocarbons, primarily short-chain n-alkanes and certain monoaromatic hydrocarbons, in oil sands tailings ponds produces large volumes of CH(4) in situ. We characterized the microbial communities involved in methanogenic biodegradation of whole naphtha (a bitumen extraction solvent) and its short-chain n-alkane (C(6)-C(10)) and BTEX (benzene, toluene, ethylbenzene, and xylenes) components using primary enrichment cultures derived from oil sands tailings. Clone libraries of bacterial 16S rRNA genes amplified from these enrichments showed increased proportions of two orders of Bacteria: Clostridiales and Syntrophobacterales, with Desulfotomaculum and Syntrophus/Smithella as the closest named relatives, respectively. In parallel archaeal clone libraries, sequences affiliated with cultivated acetoclastic methanogens (Methanosaetaceae) were enriched in cultures amended with n-alkanes, whereas hydrogenotrophic methanogens (Methanomicrobiales) were enriched with BTEX. Naphtha-amended cultures harbored a blend of these two archaeal communities. The results imply syntrophic oxidation of hydrocarbons in oil sands tailings, with the activities of different carbon flow pathways to CH(4) being influenced by the primary hydrocarbon substrate. These results have implications for predicting greenhouse gas emissions from oil sands tailings repositories.

  1. Effect of bioremediation agents on oil biodegradation in medium-fine sand

    International Nuclear Information System (INIS)

    Croft, B.C.; Swannell, R.P.J.; Grant, A.L.; Lee, K.

    1995-01-01

    A spill of weathered Arabian light crude oil on an intertidal sand zone was simulated in the laboratory. Respirometry, chemical, and microbiological methods were employed to assess the effectiveness of two bioremediation agents: a slow-release inorganic (Max Bac) and an oleophilic organic fertilizer (Inipol EAP22). Inipol EAP22 stimulated additional CO 2 evolution, and significantly increased both the total chemoheterotrophic population and the number of hydrocarbon-degrading microorganisms. At the end of the experiment, the residual oil extracted from the Inipol-treated sand was significantly more biodegraded, based on the application of the conserved biomarkers (phytane and 17α, 21β hopane), than that removed from the other sand columns, albeit by a relatively small amount. The results suggested that Inipol EAP22 stimulated the chemoheterotrophic and hydrocarbon-degrading microbial population and, after a lag phase, encouraged oil biodegradation in fine sandy sediments subjected to a vertical tidal cycle

  2. Fuel options for oil sands

    International Nuclear Information System (INIS)

    Wise, T.

    2005-01-01

    This presentation examined fuel options in relation to oil sands production. Options include steam and hydrogen (H 2 ) for upgrading; natural gas by pipeline; bitumen; petroleum coke; and coal. Various cost drivers were also considered for each of the fuel options. It was noted that natural gas has high energy value but the capital cost is low, and that coke's energy value is very low but the capital cost is high. A chart forecasting energy prices was presented. The disposition of Western Canada's northern gas situation was presented. Issues concerning rail transportation for coal were considered. Environmental concerns were also examined. A chart of typical gas requirements for 75,000 B/D oil sands projects was presented. Issues concerning steam generation with gas and mining cogeneration with gas fuel and steam turbines were discussed, as well as cogeneration and H 2 with gas fuels and steam turbines. Various technology and fuel utility options were examined, along with details of equipment and processes. Boiler technologies were reviewed by type as well as fuel and steam quality and pressure. Charts of cogeneration with gas turbine and circulation fluid bed boilers were presented. Gasification processes were reviewed and a supply cost basis was examined. Cost drivers were ranked according to energy, operating considerations and capital investment. Results indicated that fuel costs were significant for gas and coal. Capital costs and capital recovery charge was most significant with coal and gasification technology. Without capital recovery, cash costs favour the use of bitumen and coke. Gasification would need lower capital and lower capital recovery to compete with direct burning. It was concluded that direct burning of bitumen can compete with natural gas. With price volatility anticipated, dual fuel capability for bitumen and gas has merit. Petroleum coke can be produced or retrieved from stockpiles. Utility supply costs of direct burning of coke is

  3. Integrated oil sands tailings pond water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Z. [Saskatchewan Research Council, Saskatoon, SK (Canada)

    2010-07-01

    This PowerPoint presentation discussed research currently being conducted to treat oil sands tailings pond water (TPW). The treatment of TPW is challenged by the high level of naphthenic acids (NAs), the slow settling rate of fine particulate materials, and the complex chemistry of the water. The treatment process consisted of bioflocculation, sludge blanket assisted clarification, ozonation, and oil sands coke assisted hybrid biodegradation. The aggregation and adsorption process bound small particles and cells together while also ensuring the passive uptake of pollutants using microbial masses. The mixed liquor then passed through a sludge blanket to ensure enhanced particle capture. An ozonation process was used to increase the biodegradability of the TPW as well as to increase the biodegradability of the residual NAs after ozonation. The process used a hybrid bioreactor that consisted of both suspended and fixed microbial communities. The coke served as a biofilm carrier for the waste. Further studies are being conducted to investigate the efficiency and capability of the process. tabs., figs.

  4. Steam producing plant concept of 4S for oil sand extraction

    International Nuclear Information System (INIS)

    Matsuyama, Shinichiro; Nishiguchi, Youhei; Sakashita, Yoshiaki; Kasuga, Shoji; Kawashima, Masatoshi

    2009-01-01

    Plant concept of small fast reactor '4S' applying to continuous steam production for recovery of crude oil from oil sands was investigated. Assuming typical steam assisted gravity drainage (SAGD) plant whose production scale is 120,000 barrels per day of a crude oil, concept of nuclear steam supply system consisting of eight reactor modules for steam production and three reactor modules for electric generation of the 4S with a thermal rating of 135 MWt was established without any essential or significant design change from the preceding 4S with a thermal rating of 30 MWt. The 4S, provided for an oil sand extraction, will reduce greenhouse gas emission significantly, and has not much burden for development and licensing and has economic competitiveness. (author)

  5. Oxidizing oils, etc. [British patent

    Energy Technology Data Exchange (ETDEWEB)

    Penniman, W B.D.

    1926-03-02

    The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tar, and oils containing powdered coal, coke or peat, sulphur in suspension, is effected by passing air or other oxygen-containig gas through a layer of the material of a depth sufficient substantially to deoxygenate the air, the pressure being at or below atmospheric pressure.

  6. Insight conference reports : western Canada oil sands summit : meeting North America's energy needs

    International Nuclear Information System (INIS)

    2004-01-01

    This conference focused on exploration and development of oil sands in western Canada, with particular reference to market opportunities and challenges for oil sands exploitation in Alberta, risk management in large resource development projects, pipeline issues, investment issues, and asset life cycle management. Some presentations also addressed regulatory regimes, royalty regimes, taxes, resource potential, research activities, environmental impacts, and offshore prospects. Both industry and government have an interest in ensuring resources are developed in a sustainable manner. The influence of the Kyoto Protocol on oil sands development and the greenhouse gas emissions market was also addressed along with joint venture issues and a comparison of extra-heavy crude oil projects in Venezuela and Canada. The conference featured 20 presentations, of which 8 have been indexed separately for inclusion in this database. refs., tabs., figs

  7. Physiological and biochemical responses of small fish exposed to Athabasca oil sands sediment

    International Nuclear Information System (INIS)

    Tetrault, G.R.; Environment Canada, Burlington, ON; McMaster, M.E.; Dixon, D.G.; Parrott, J.L.

    2002-01-01

    A study was conducted to determine the influence of naturally occurring oil sands related compounds on the reproductive function and hepatic responses of fish. Wild fish, both exposed and unexposed to the compounds in question, were collected along with sediments for laboratory testing. The study showed that in vitro gonadal incubation levels of steroid production were lower at the tributary sites within the oil sands deposits. One indicator of exposure to oil sands related compounds (hepatic 7-ethoxyresorufin-O-deethylase activity) was shown to be 5 times higher at the same sites. In addition, slimy sculpin were exposed to sediment samples from the Steepbank River site for 4 to 8 days to evaluate the absorption of the indicator. The indicator in exposed fish was found to be comparable to that measured in fish native to the oil sands area. The study was not capable of predicting an altered ability of gonadal tissue of exposed fish to produce steroid hormones in vitro. It was concluded that future development could compromise the reproductive health of fish in the area

  8. Influence of Geometric Parameters of the Hydrocyclone and Sand Concentration on the Water/Sand/Heavy-Oil Separation Process: Modeling and Simulation

    Directory of Open Access Journals (Sweden)

    F Farias

    2016-09-01

    Full Text Available In the oil exploitation, produced fluids are composed of oil, gas, water and sand (depending on the reservoir location. The presence of sand in flow oil leads to several industrial problems for example: erosion and accumulation in valves and pipeline. Thus, it is necessary to stop production for manual cleaning of equipments and pipes. These facts have attracted attention of academic and industrial areas, enabling the appearing of new technologies or improvement of the water/oil/sand separation process. One equipment that has been used to promote phase separation is the hydrocyclone due to high performance of separation and required low cost to installation and maintenance. In this sense, the purpose of this work is to study numerically the effect of geometric parameters (vortex finder diameter of the hydrocyclone and sand concentration on the inlet fluid separation process. A numerical solution of the governing equations was obtained by the ANSYS CFX-11 commercial code. Results of the streamlines, pressure drop and separation efficiency on the hydrocyclone are presented and analyzed. It was observed that the particles concentration and geometry affect the separation efficiency of the hydrocyclone.

  9. Solvent refining of low-temperature tar with liquid ammonia

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, K

    1953-01-01

    The middle fractions of low-temperature tar were treated with mixed solutions of H/sub 2/O and liquid NH/sub 3/ at 0/sup 0/ and 20/sup 0/, and with liquid NH/sub 3/ at -10, 0, + 10, and 20/sup 0/, and phase equilibrium between tar acids, neutral oil, and solvents were studied. The distribution ratio ranged from less than 1 to greater than 1 when the solvent contained about 20 percent (by weight) H/sub 2/O. When the solvent contained less than 85 percent (by weight) NH/sub 3/, the yield of extract was small but the purity of phenols in the extracted oil was above 90 percent. Solvent containing about 85 percent NH/sub 3/ (by weight) is considered optimum for separating tar acids from oils. A novel definition is proposed for solvent selectivity as the difference between the concentration of the solute in the extract layer, on a solvent-free basis, and the concentration in the raffinate layer.

  10. Aquatic toxicity of petroleum products and dispersant agents determined under the U.S. EPA Oil Spill Research Program

    Science.gov (United States)

    The U.S. EPA Office of Research and Development has developed baseline data on the ecotoxicity of selected petroleum products and several chemical dispersants as part of its oil spills research program. Two diluted bitumens (dilbits) from the Alberta Tar Sands were tested for acu...

  11. EX8000 ramps up preparation phase in Horizon oil sands project

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2006-07-15

    This article presented details of Hitachi's EX8000 hydraulic shovel, a key piece of equipment that will be used throughout the extensive mine preparation phase of the Horizon oil sands project. Within 2 years, the project expects to produce over 200,000 barrels of oil per day. However, more than 400 million cubic metres of soil will need to be moved before production can begin. In order to remain on schedule, overburden must be removed in massive volumes. With a 52.3 cubic yard bucket, the Hitachi EX8000 has the capacity to feed a dozen 320 metric tonne haul trucks as well as several smaller 282 metric tonne trucks, and can fill each truck in 4 passes. Material is now being moved by to an area in which dikes are being constructed to house water generated in the refining process. Stockpiling, relocation and reclamation phases will follow as the project progresses. In order to reach the oil, as much as 75 feet of overburden must be removed, including layers of sandstone, limestone, trap rock and other materials. Once the overburden has been removed, oil sand layers are also often intermixed with other materials. The EX8000 can separate the tramp material from the oil sands, improving the overall efficiency of the operation. The Alberta-based North American Construction Group, who have a 10-year contract with Canadian Natural Resources Ltd. for the Horizon project, owns more than 100 Hitachi units in various sizes and has already purchased another EX8000 which is slated for delivery in the Fall of 2006. It was concluded that the company has purchased hundreds of new trucks to handle added volumes of materials being moved as the oil sands industry gains momentum. 3 figs.

  12. More oil sand cooperation between Canada and Venezuela

    Energy Technology Data Exchange (ETDEWEB)

    1977-07-01

    Venezuela has pioneered the production of heavy oil, according to Dr. A. Guzman-Reyes, director general of hydrocarbons for the Venezuelan government. The first heavy oil production began in Venezuela 60 yr ago and the oil industry has steadily improved methods of producing and handling heavy oil. The country's producing fields are capable of yielding almost one million barrels of heavy oil daily, although actual production, largely because of market limitations, is about 650,000 bpd. Canada's daily heavy oil production, including the 60,000 bbl of synthetic crude produced daily by the Great Canadian Oil Sands plant, is about 200,000 bbl. Dr. Guzman-Reyes stated that Venezuela intends to rapidly develop heavy oil production and upgrade facilities to maintain its export markets. The national oil company, Petroleos de Venezuela, plans to invest 4 times the amount spent on oil development over the last 60 yr during the next 10 yr, a total of $3 billion by 1980.

  13. Applications of Nuclear Energy to Oil Sands and Hydrogen Production

    International Nuclear Information System (INIS)

    Duffey, R.B.; Miller, A.; Kuran, S.

    2011-01-01

    Many novel and needed applications of nuclear energy arise in today's energy-hungry, economically challenged world, and in solving tomorrow's search for a globally carbon-constrained and sustainable energy supply. Not only can nuclear power produce low cost electricity, it can provide co-generation of process heat, desalinated water, and hydrogen with negligible greenhouse gas emissions. In each of these new applications, nuclear energy is competing against, or displacing conventional and established use of natural gas or coal in thermal power plants and boilers. Therefore, there must be a compelling case, in terms of supply certainty, stability, safety, security, and acceptability. In addition, a synergistic relation must exist or be created with the existing power and energy markets, the use of windpower, and the needs for low-cost supply with negligible greenhouse gas emissions and carbon 'footprint'. The development of Canada's oil sands resource depends on a substantial energy input for extraction and upgrading. So far, this input has been supplied by natural gas, a resource that (a) is a premium fuel; (b) has constrained availability; and (c) produces significant CO 2 emissions. For the oil sands extraction process, natural gas is the current energy source used to generate the steam for in-situ heating, the power to drive the separation equipment, and the hydrogen for varying degrees of upgrading before piping. Nothwithstanding the current imbalance between supply and demand for gas within North America, the very demand of the oil sands for prodigious amounts of natural gas has itself the potential to force higher prices and create supply constraints for natural gas. Rooted in the energy equivalence of oil and gas, there is a long-established link between American gas prices whereby one bbl of oil is worth 7 GJ of natural gas. Temporary supply/demand imbalances apart, only cheap oil can maintain cheap gas. Only the improbability of cheap oil will maintain low

  14. Advanced characterisation of organic matter in oil sands and tailings sands used for land reclamation by Fourier transform-ion cyclotron resonance-mass spectrometry (FT-ICR-MS).

    OpenAIRE

    Mareike Noah; Andrea Vieth-Hillebrand; Heinz Wilkes

    2012-01-01

    The Athabasca region of northern Alberta, Canada, is home to deposits of oil sands containing vast amounts (~ 173 billion barrels) of heavily biodegraded petroleum. Oil sands are recovered by surface mining or by in situ steam injection. The extraction of bitumen from oil sands by caustic hot water processing results in large volumes of fluid tailings, which are stored in on-site settling basins. There the tailings undergo a compaction and dewatering process, producing a slowly densifying sus...

  15. The growth and photosynthesis of Typha in oil sands process affected material and water

    Energy Technology Data Exchange (ETDEWEB)

    Foote, L. [Alberta Univ., Edmonton, AB (Canada); Hornung, J. [Petro-Canada, Calgary, AB (Canada)

    2007-07-01

    Aquatic plants such as cattail contribute substantially to the energy flow in wetlands. Since Typha (cattail) plants acquire and cycle carbon and nutrients through wetlands, their growth and recycling of captured nutrients are an important part of natural, healthy wetland ecosystems. Cattail are pervasive and satisfy many of the criteria to be used as indicators of wetland integrity. This study investigated if cattail growth and carbon accrual were influenced by oil sands process materials (OSPM) such as consolidated tailings (CT). The purpose was to facilitate land reclamation initiatives by evaluating the impact that constituents of oil sands process material have on aquatic plant growth. The study was conducted at Suncor's experimental trenches. Six lined basins were used, of which 3 were filled with natural water and 3 were filled with trench water. Cattail were planted in different growth medium combinations, including CT over CT; soil over soil; soil over CT; and soil over sterilized sand. All leaf lengths and widths were measured along with the photosynthesis of the leaves and root and plant biomass at planting and after 2-years growth. A larger leaf area was observed under oil sands process influence, which may indicate increased carbon accrual above ground. Leaf area data suggested that CT affected plants are quite productive. The study also indicated that oil sands affected water may reduce plant fitness, and therefore could influence the overall oil sands reclamation timelines. Conversely, cattail grown in soil capped process affected material had a much larger leaf area compared to those grown in soil capped sand, most likely due to the higher levels of ammonia in process affected material.

  16. Easing the capacity crunch : infrastructure requirements to support rapidly developing oil sands

    International Nuclear Information System (INIS)

    Zupan, L.

    2003-01-01

    Through annual consultation with its customers, Enbridge develops a supply and demand forecast which forms the basis for the company's development. It is complex to develop the appropriate pipeline infrastructure to support resource development, based on the significant forecast growth in supply in Alberta from oil sands and the limited traditional markets. The largest crude oil pipeline serving the oil sands industry in Alberta is owned and operated by Enbridge. The first customer was Suncor, followed by PetroCanada and EnCana. In 2002, a pipeline concept was developed by Enbridge to provide a link to Edmonton via a new large diameter pipeline. The mainline system which originates in Edmonton is expected to evolve and grow as oil sands production comes on line. The completion of Terrace Phase III expansion is one of the priorities for Enbridge in 2003. Other projects involve the extension of one of its lines from Mokena to Chicago, the segregation of batches on the system to improve quality of its deliveries, and extension and expansion into new markets. Shipper support will determine the scale of these developments. The Canadian Association of Petroleum Producers (CAPP) has undergone a market study, as has Enbridge (Oil Sands Markets Study) in an effort to better understand markets and potential markets. It will assist in the determination of which pipeline infrastructure requires expansion, as well as the extent of infrastructure required to support new markets. tabs., figs

  17. Clean energy and hydrogen for oil sands development with CANDU SCWR nuclear reactors and Cu-Cl cycles

    International Nuclear Information System (INIS)

    Wang, Z.L.; Naterer, G.F.; Gabriel, K.S.

    2010-01-01

    In this paper, the unique capabilities and advantages of SCWR technology for cleaner oil sands development are discussed from two perspectives: lower temperature steam generation by supercritical water for steam assisted gravity drainage (SAGD), and hydrogen production for oil sands upgrading by coupling SCWR with the thermochemical copper-chlorine (Cu-Cl) cycle. The heat requirements for bitumen extraction from the oil sands and the hydrogen requirements for bitumen upgrading are evaluated. A conceptual layout of SCWR coupled with oil sands development is presented. The reduction of CO 2 emissions due to the use of SCWR and thermo chemical hydrogen production cycle is also analyzed. (author)

  18. Loadings of polynuclear aromatic compounds and metals to the Athabasca River watershed by oil sands mining and processing

    International Nuclear Information System (INIS)

    Hodson, P.V.

    2010-01-01

    The contribution of oil sands operations to pollution in the Athabasca River has not yet been determined. Wastes from oil sands processes include recycled water, sand, silt, clay, bitumen, and polycyclic aromatic compounds (PAC) and metals. Upgrading processes can also release significant quantities of PAC and heavy metals. This paper discussed a study in which PAC and metals in the snow pack and river water of the Athabasca watershed were assessed. The study showed that the oil sands industry is a significant source of contamination. The equivalent of 600 T of bitumen was observed at sites within 50 km of oil sands upgrading facilities. The strongest contamination signals occurred during the summer months, which suggested that the surface run-off of contaminated water was related to recent oil sands developments. Samples taken from tributaries in watersheds with little or no development indicated that increased concentrations of oil sands related contaminants were not caused by natural erosion. The contaminants may contribute to higher levels of mercury (Hg) and cadmium (Cd) in the flesh of fish and wildlife and increase toxicity to the embryos of spring-spawning fish.

  19. Life cycle energy and greenhouse gas emissions from transportation of Canadian oil sands to future markets

    International Nuclear Information System (INIS)

    Tarnoczi, Tyler

    2013-01-01

    Oil sands transportation diversification is important for preventing discounted crude pricing. Current life cycle assessment (LCA) models that assess greenhouse gas (GHG) emissions from crude oil transportation are linearly-scale and fail to account for project specific details. This research sets out to develop a detailed LCA model to compare the energy inputs and GHG emissions of pipeline and rail transportation for oil sands products. The model is applied to several proposed oils sands transportation routes that may serve as future markets. Comparison between transportation projects suggest that energy inputs and GHG emissions show a high degree of variation. For both rail and pipeline transportation, the distance over which the product is transported has a large impact on total emissions. The regional electricity grid and pump efficiency have the largest impact on pipeline emissions, while train engine efficiency and bitumen blending ratios have the largest impact on rail transportation emissions. LCA-based GHG regulations should refine models to account for the range of product pathways and focus efforts on cost-effective emission reductions. As the climate-change impacts of new oil sands transportation projects are considered, GHG emission boundaries should be defined according to operation control. -- Highlights: •A life cycle model is developed to compare transportation of oil sands products. •The model is applied to several potential future oil sands markets. •Energy inputs and GHG emissions are compared. •Model inputs are explored using sensitivity analysis. •Policy recommendations are provided

  20. Enhanced Gravitational Drainage of Crude Oil Through Alabama Beach Sand Caused by the Dispersant Corexit 9500A

    Science.gov (United States)

    Steffy, D. A.; Nichols, A.; Hobbs, K.

    2017-12-01

    Oil spill material released by the 2010 Deepwater Horizon accident contaminated a majority of the 60 miles of Alabama coastline. In response to the oil spill, BP sprayed a dispersant, Corexit 9500A, as an initial remediation effort. An unforeseen impact of the saltwater-dispersant mixture includes the mobilization of oil-spilled material into the underlying beach sand. This study investigated the effect of the dispersant to promote gravitational drainage by measuring the physical characteristics of the sand, saltwater, crude oil, and the dispersant solution. The saltwater-dispersant mixture promoted the downward movement of oil mass 20 times greater extent than just saltwater. These tests are meant to simulate spill material on the beach being exposed to a low-energy, 1-meter mixed tide occurring along the Alabama coastline. A separate test simulated oilwet sand exposed to saltwater and a saltwater-dispersant mixture. The oil-wet sand impeded the vertical movement of saltwater, but allowed a saltwater-dispersant solution to mobilize the oil to migrate downward. The mobilization of oil in this three phase system of saltwater, oil, and air is controlled by: the pressure-saturation profile of the sand; interfacial tension with saltwater; and its surface tension with air.

  1. The use of small modular nuclear reactors for Canadian Oil Sands applications: a proposal and way forward

    Energy Technology Data Exchange (ETDEWEB)

    Attwood, D., E-mail: ergo.applications@gmail.com [Human Factors Applications, Toronto, Ontario (Canada); Moledina, M., E-mail: mohamedmoledina@rogers.com [Consultant, Toronto, Ontario (Canada)

    2013-07-01

    It has been estimated that Canada's Oil Sands contain between 160 and 200 billion barrels of oil reserves - the second largest accumulation of oil in the world after Saudi Arabia. It is also estimated that by 2015, output from the oil sands should increase from about 1 million barrels per day (mbbl/day) to approximately 4 mbbl/day. However, Canada and the world have to pay a price for oil extraction from the sands.It is estimated that about 40 cubic metres of natural gas as fuel must be burned for each barrel of synthetic crude produced. Therefore, if oil sands production did reach 4 mbbl/day, natural gas use for oil production could seriously limit exports of natural gas to the US. It has also been estimated that every barrel of synthetic oil pollutes about 950 liters of fresh water and emits about 100 Kg of Carbon Dioxide (CO{sub 2}) along with other pollutants. Clearly an alternate source of energy is required for oil sands production that will allow our natural gas to be put to better use while simultaneously sustaining our environment. The energy must be continuously obtainable and not be subject to the intermittent availability of wind or sunlight. Nuclear energy is the obvious choice. Nuclear energy for power generation has been prevalently used around the world since the 1950's. Today, there are more than 440 Nuclear Power Plants(NPPs) operating safely worldwide. Each has different characteristics that would make them comparatively acceptable for operation in Northern Canada. This paper will briefly review the various types of nuclear plants that are currently in operation or are being licensed worldwide,as well as those that are proposed for operation in the near future including small nuclear power reactors (< 300 me). Moreover, it will propose a list of the NPP characteristics that are best suited to oil sands operation. This will lead to a proposal to encourage the development of small modular reactors (SMRs) for installation in oil sands

  2. Predicting development of undrained shear strength in soft oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Masala, S. [Klohn Crippen Berger, Calgary, AB (Canada); Matthews, J. [Shell Canada Ltd., Calgary, AB (Canada)

    2010-07-01

    This PowerPoint presentation discussed a method of predicting the development of undrained shear strength in soft oil sands tailings. Phenomenology charts of oil sands tailings ponds were used to present the suspension, density, stresses and hydrostatic behaviour of tailings. Sedimentation and consolidation processes were discussed. The charts demonstrated how the tailings slurry settles and consolidates, releases water and dissipates pore pressures. The slurry then develops intergranular stresses and increases in density. The increases correlate with increased resistance to deformation and decreased compressibility and hydraulic conductivity. A critical state soil mechanics (CSSM) was used to characterize the soft oil sands tailings. Undrained strength was determined using the concept of the undrained strength ratio (USR). The USR was determined using traditional geotechnical investigation methods. Settling of the non-consolidated (NC) soil deposits was simulated using the finite strain consolidation theory. The model was based on the premise that current effective stresses control undrained shear strength in the NC deposits. Case studies were used to demonstrate the predictive framework. tabs, figs.

  3. Characterisation and catalytic upgrading of tars from coal-tyre hydropyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Mastral, A.M.; Murillo, R.; Callen, M.S.; Garcia, T. [Instituto de Carboquimica, Zaragoza (Spain)

    1999-07-01

    Tars from coal-tyre hydropyrolysis obtained in a swept fixed bed reactor were upgraded with catalysts. Upgraded oils were characterized, and naphtha, kerosene, gas oil, heavy gas oil and vacuum residue percentages were quantified. 7 refs., 3 tabs.

  4. Hydraulic fracture considerations in oil sand overburden dams

    Energy Technology Data Exchange (ETDEWEB)

    Cameron, R.; Madden, B.; Danku, M. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

    2008-07-01

    This paper discussed hydraulic fracture potential in the dry-filled temporary dams used in the oil sands industry. Hydraulic fractures can occur when reservoir fluid pressures are greater than the minimum stresses in a dam. Stress and strain conditions are influenced by pore pressures, levels of compaction in adjacent fills as well as by underlying pit floor and abutment conditions. Propagation pressure and crack initiation pressures must also be considered in order to provide improved hydraulic fracture protection to dams. Hydraulic fractures typically result in piping failures. Three cases of hydraulic fracture at oil sands operations in Alberta were presented. The study showed that hydraulic fracture failure modes must be considered in dam designs, particularly when thin compacted lift of dry fill are used to replace wetted clay cores. The risk of hydraulic fractures can be reduced by eliminating in situ bedrock irregularities and abutments. Overpressure heights, abutment sloping, and the sloping of fills above abutments, as well as the dam's width and base conditions must also be considered in relation to potential hydraulic fractures. It was concluded that upstream sand beaches and internal filters can help to prevent hydraulic fractures in dams in compacted control zones. 5 refs., 16 figs.

  5. Process water treatment in Canada's oil sands industry : 2 : a review of emerging technologies

    International Nuclear Information System (INIS)

    Allen, E.W.

    2008-01-01

    This review was conducted to identify candidate treatment technologies for treating oil sands process water. The oil sands industry in Canada uses large volumes of fresh water in order to extract bitumen deposits. The development of process water treatment technologies has become a critical issue for the industry, particularly as oil sand production is expected to triple in the next decade. However, treatment technologies must be adapted to consider the fouling potential of bitumens and fine clays as well as the effect of alkaline process water on treatment performance. The review included developments in chemical modifications to membranes and adsorbents designed to improve pollutant removal and reduce fouling; hybridization technologies designed to enhance the biological treatment of toxic feedwaters; recent advances in photocatalytic oxidation technologies for organic compounds; and new designs for large-scale treatment wetlands for polluted waste waters. It was concluded that major knowledge gaps must be optimized and preliminary studies must be conducted in order to understand how the treatment technologies will be affected by the chemical and physical characteristics of oil sands process water. 188 refs., 8 tabs

  6. BioTiger{sup TM} : a natural microbial product for enhanced hydrocarbon recovery from oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Brigmon, R.L.; Berry, C.J.; Milliken, C.E.; Jones, W. [Savannah River National Laboratory, Aiken, SC (United States)

    2008-07-01

    This presentation discussed the feasibility of using BioTiger{sup TM} technology to increase hydrocarbon recovery from oil sands. This enhanced ex situ oil recovery processes was initially developed and used by the United States Department of Energy for bioremediation of soils contaminated with oil, but it may also be used to optimize bitumen separation. BioTiger was described as being a unique microbial consortia that has resulted from nearly a decade of extensive microbiology screening and characterization of samples collected from an old waste lagoon. The technology offers rapid and complete degradation of aliphatic and aromatic hydrocarbons and produces new surfactants. It is tolerant of both chemical and metal toxicity and has good activity at high temperatures at extreme pH levels. A flotation test protocol with oil sands from Fort McMurray, Alberta was used for the BioTiger evaluation. A comparison of hot water extraction/flotation test of the oil sands performed with BioTiger showed a 50 per cent improvement in separation as measured by gravimetric analysis. BioTiger is well suited for enhanced hydrocarbon recovery from oil sands because it performs well at high temperatures. 8 figs.

  7. Semipermeable membrane devices concentrate mixed function oxygenase inducers from oil sands and refinery wastewaters

    International Nuclear Information System (INIS)

    Parrott, J.L.; Hewitt, L.M.

    2002-01-01

    The health of fish in the Athabasca River was examined to determine the effects of both natural and anthropogenic oil sands exposure on liver mixed function oxygenase (MFO) enzymes. Semipermeable membrane devices (SPMD) were used to concentrate bioavailable compounds that may result in MFO induction. The SPMDs were used for a period of 2 weeks in the Steepbank River as well as in oil refinery wastewater and intake ponds. They were then tested to see if they induced ethoxyresorufin-O-deethylase (EROD) activity in hepatoma cells, a cell line derived from a liver cancer of a small fish. SPMDs from the wastewater pond contained potent EROD inducers in fish liver cells. SPMDs from the Athabasca River exhibited some EROD inducers, but they were 1/100 as potent as those of the refinery wastewater. The characteristics of MFO inducers from refinery wastewater were different from natural inducers from the oil sands in the Athabasca and Steepbank Rivers. For instance, log Kow was less than 5 for refinery wastewater, but it was greater than 5 for Athabasca River wastewater and from natural oil sands exposure. In the case of the Steepbank River, the pattern of MFO induction was similar to the MFO induction seen in wild fish.The highest MFO inducers were found to be in the area of the mine, suggesting and anthropogenic pollution source. The less potent inducers were in the area of the natural and undisturbed oil sands. Very few inducers were found outside of the oil sands formation

  8. Advanced characterisation of organic matter in oil sands and tailings sands used for land reclamation by Fourier transform-ion cyclotron resonance-mass spectrometry (FT-ICR-MS)

    Science.gov (United States)

    Noah, M.; Vieth-Hillebrand, A.; Wilkes, H.

    2012-04-01

    The Athabasca region of northern Alberta, Canada, is home to deposits of oil sands containing vast amounts (~ 173 billion barrels) of heavily biodegraded petroleum. Oil sands are recovered by surface mining or by in situ steam injection. The extraction of bitumen from oil sands by caustic hot water processing results in large volumes of fluid tailings, which are stored in on-site settling basins. There the tailings undergo a compaction and dewatering process, producing a slowly densifying suspension. The released water is recycled for extraction. The fine tailings will be reclaimed as either dry or wet landscapes. [1] To produce 1 barrel of crude oil, 2 tons of oil sand and 2 - 3 tons of water (including recycled water) are required. [2] Open pit mining and the extraction of the bitumen from the oil sands create large and intense disturbances of different landscapes. The area currently disturbed by mining operations covers about 530 km2 and the area of tailing ponds surpasses 130 km2. An issue of increasing importance is the land remediation and reclamation of oil sand areas in Canada and the reconstruction of these disturbed landscapes back to working ecosystems similar to those existing prior to mining operations. An important issue in this context is the identification of oil sand-derived organic compounds in the tailings, their environmental behaviour and the resulting chances and limitations with respect to land reclamation. Furthermore the biodegradation processes that occur in the tailings and that could lead to a decrease in hazardous organic compounds are important challenges, which need to be investigated. This presentation will give a detailed overview of our compositional and quantitative characterisation of the organic matter in oil sand, unprocessed and processed mature fine tailings samples as well as in tailings sands used as part of land reclamation. The analytical characterisation is based on the extraction of the soluble organic matter, its

  9. How confident is Fort McKay that industry can reclaim oil sand development

    Energy Technology Data Exchange (ETDEWEB)

    Fitzpatrick, C. [Fort McKay First Nations, AB (Canada)

    2004-02-05

    This presentation described how traditional environmental knowledge (TEK) can provide valuable information for both the reclamation design and assessment of oil sand development in Fort McKay. Conservation is valued by the Fort McKay First Nations communities who claim that current reclamation methods are too slow, and that the land is not being brought back to its original use with the uniqueness of the boreal landscape. Elders have noted that each year the water level in the Athabasca River is lower. The blowing tailings and coke dust are causing trees to dye and driving animals away. There is concern that the animals that remain may not be safe to eat. The Fort McKay First Nation community has stated that it will view reclamation as a success only when it functions with proof over many generations. The major concerns include: salt in the water draining from reclaimed areas; salt in the soils of reclaimed area; muskeg cannot be recreated; and, the issue of whether cranberry, blueberry and streambank forest areas can be recreated, along with traditional medicinal plants. Other concerns include the loss of rivers such as the Beaver Creek and Tar River, and that the water in reclaimed areas may not be suitable for animals to live in or to drink. tabs., figs.

  10. How confident is Fort McKay that industry can reclaim oil sand development

    International Nuclear Information System (INIS)

    Fitzpatrick, C.

    2004-01-01

    This presentation described how traditional environmental knowledge (TEK) can provide valuable information for both the reclamation design and assessment of oil sand development in Fort McKay. Conservation is valued by the Fort McKay First Nations communities who claim that current reclamation methods are too slow, and that the land is not being brought back to its original use with the uniqueness of the boreal landscape. Elders have noted that each year the water level in the Athabasca River is lower. The blowing tailings and coke dust are causing trees to dye and driving animals away. There is concern that the animals that remain may not be safe to eat. The Fort McKay First Nation community has stated that it will view reclamation as a success only when it functions with proof over many generations. The major concerns include: salt in the water draining from reclaimed areas; salt in the soils of reclaimed area; muskeg cannot be recreated; and, the issue of whether cranberry, blueberry and streambank forest areas can be recreated, along with traditional medicinal plants. Other concerns include the loss of rivers such as the Beaver Creek and Tar River, and that the water in reclaimed areas may not be suitable for animals to live in or to drink. tabs., figs

  11. A novel waste water cleanup, fines sequestration and consolidation technology for oil sands applications

    Energy Technology Data Exchange (ETDEWEB)

    Soane, D.; Ware, W.; Mahoney, R.; Kincaid, P. [Soane Energy LLC, Cambridge, MA (United States)

    2010-07-01

    This paper discussed a wastewater technology designed to rapidly sequester suspended fines and other pollutants from the tailings produced during oil sands processes. The technology can also be used to clarify existing tailings ponds, and is expected to help address growing environmental concerns over the remediation of oil sands tailings. The ATA system is comprised of the following 3 components: (1) an activator polymer, (2) a tether polymer, and (3) an anchor particle. A small dose of the activator polymer is added to the fine or mature tailings, which then causes the suspended clay fines to aggregate. The anchor particles are then coated with the tether polymer. The anchor particle is formed from sand derived from coarser tailings. The tether-bearing anchor particles bind to the aggregated clay fines in the activated tailings to form robust complexes that can easily be separated from the waste stream. Output streams from the ATA process include a clean water stream that can be reused in oil sands extraction processes; and a dewatered solid that can be used as landfill as well as in construction and reclamation applications. The sensible heat retained in the recycled water is expected to also reduce the energy requirements of the oil sands extraction process. 6 refs., 1 tab., 5 figs.

  12. Microstructure and properties of lignite tar and pitch. Part II

    Energy Technology Data Exchange (ETDEWEB)

    Walther, H

    1954-01-01

    Photomicrographs reveal the presence of crystalline wax which affects the working properties in lignite tars and pitch. The crystals are large needles after slow cooling and small after rapid cooling. The crystals are paraffinic in character. All samples were nonhomogeneous. Thus the properties of lignite tar and pitch are varied by the source of the lignite and history of the specimen, neither softening point nor dropping point seems to satisfactorily characterize these tars. The samples exhibit thixotropic behavior characteristic of a structural viscosity and show hysteresis loops on varying the working rate. The variations have hindered use of lignite tars and pitches except where solubility in a solvent such as coal tar oil can be used to advantage.

  13. Influence of Oil Saturation Upon Spectral Induced Polarization of Oil Bearing Sands

    Science.gov (United States)

    The presence of oil in an unconsolidated granular porous material such as sand changes both the resistivity of the material and the value of the phase shift between the low-frequency current and the voltage. The resistivity and the phase angle can be written as a complex-valued r...

  14. Applications in the oil sands industry for Particlear{sup R} silica microgel

    Energy Technology Data Exchange (ETDEWEB)

    Moffett, B. [DuPont Chemical Solutions Enterprise, Wilmington, DE (United States)

    2009-07-01

    This presentation demonstrated the use of Particlear{sup R} silica microgel in the oil sands industry. The silica-based coagulant is an amorphous silicon dioxide microgel solution. The surface area of a football field can be obtained using 2.7 grams of the substance. The coagulation mechanism is achieved by charge neutralization and inter-particle bridging. The microgel is manufactured at the point of use from commodity chemicals, water, and carbon dioxide (CO{sub 2}). Applications for the microgel include potable water treatment, paper retention, and animal processing wastewater. In the oil sands industry, Particlear{sup R} can be used in tailings flocculation, thickened tailings drying, steam assisted gravity drainage (SAGD) water treatment, and enhanced bitumen recovery. It was concluded that the microgel can be used in many oil sands processing and liquid-solid separation processes in order to remove dissolved solids and organics and increase the rate of solids dewatering. tabs., figs.

  15. Log analysis in the shallow oil sands of the San Joaquin Valley, California

    International Nuclear Information System (INIS)

    Vohs, J.B.

    1976-01-01

    Many fields in the San Joaquin Valley of California produce oil from a depth of 2,500 ft or less. During the period of primary production in these fields, evaluation of potential pay intervals from logs was restricted to examination of ES logs and correlation. With the introduction of secondary and tertiary recovery techniques the need for more and better answers, more quickly available, became apparent. However, several log-analysis problems had to be resolved. Formation evaluation using well logs was complicated by the shaliness of the sand intervals, the low and variable salinity of the formation waters, and the presence of low-pressure-gas (depleted) zones in many of the shallow sands. Solutions to these problems have required more modern logging programs and interpretation techniques. Logs available for the evaluation of these sands are the dual induction-laterolog, the compensated formation density log, the compensated neutron log, and the microlaterolog or proximity log. With this suite of logs it is possible to determine the shale content, porosity, saturation in the flushed zone, and water saturation of the sand, and to locate the low-pressure-gas sands and depleted zones. In cases where freshwater and oil are interlayered, it is possible to tell which sands contain oil and which contain only water. Because a quick interpretation is required, wellsite techniques are called for. These will be described

  16. Pollutant deposition impacts on lichens, mosses, wood and soil in the Athabasca oil sands area

    International Nuclear Information System (INIS)

    Pauls, R.W.; Abboud, S.A.; Turchenek, L.W.

    1996-01-01

    A study was conducted to monitor the accumulation and impact on the environment of emissions from oil sands processing plants. SO 2 , H 2 S, NO x and hydrocarbon concentrations in the air were monitored. Syncrude Canada Ltd. conducted surveys to determine elemental levels in lichens and mosses. The objective of the study was to monitor the pattern of accumulation of emissions by oil sand plants in, and their effects on, lichens and mosses, and examine changes in wood induced by soil acidity. The moss, lichen and wood samples were analyzed for total elemental content. Soils were analyzed for pH, soluble sulphate and other properties related to soil acidity and soil composition. Little or no evidence was found to indicate that wood tissue chemistry has been affected by atmospheric deposition of substances originating from oil sands plants. These results led to the inference that no large changes in soil acidity have resulted from oil sands plant emissions either. 66 refs., 21 tabs., 124 figs

  17. Oil sands mine planning and waste management using goal programming

    Energy Technology Data Exchange (ETDEWEB)

    Ben-Awuah, E.; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering; Alberta Univ., Edmonton, AB (Canada). Mining Optimization Laboratory

    2010-07-01

    A goal programming method was used to plan waste management processes at an oil sands mine. This method requires the decision maker (DM) to set goals. Mine planning is used to determine a block extraction schedule that maximizes net present value (NPV). Due to land restrictions, tailings facilities are sited within the pit area and dykes are used to contain the tailings. Many of the materials used to construct the dykes come from the mining operation. The mine plan scheduled both ore and dyke material concurrently. Dykes were constructed simultaneously as the mine phase advanced. A model was used to classify an oil sands block model into different material types. A mixed integer goal programming (MIGP) method was used to generate a strategic schedule. Block clustering techniques were used to large-scale mine planning projects. The method was used to verify and validate synthetic and real case data related to the cost of mining all material as waste, and the extra cost of mining dyke material. A case study of an oil sands project was used to demonstrate the method. The study showed that the developed model generates a smooth and uniform strategic schedule for large-scale mine planning projects. tabs., figs.

  18. Oil sands mine planning and waste management using goal programming

    International Nuclear Information System (INIS)

    Ben-Awuah, E.; Askari-Nasab, H.; Alberta Univ., Edmonton, AB

    2010-01-01

    A goal programming method was used to plan waste management processes at an oil sands mine. This method requires the decision maker (DM) to set goals. Mine planning is used to determine a block extraction schedule that maximizes net present value (NPV). Due to land restrictions, tailings facilities are sited within the pit area and dykes are used to contain the tailings. Many of the materials used to construct the dykes come from the mining operation. The mine plan scheduled both ore and dyke material concurrently. Dykes were constructed simultaneously as the mine phase advanced. A model was used to classify an oil sands block model into different material types. A mixed integer goal programming (MIGP) method was used to generate a strategic schedule. Block clustering techniques were used to large-scale mine planning projects. The method was used to verify and validate synthetic and real case data related to the cost of mining all material as waste, and the extra cost of mining dyke material. A case study of an oil sands project was used to demonstrate the method. The study showed that the developed model generates a smooth and uniform strategic schedule for large-scale mine planning projects. tabs., figs.

  19. Heavy crude oils - From Geology to Upgrading - An Overview

    International Nuclear Information System (INIS)

    Huc, A.Y.

    2010-01-01

    Heavy oils, extra-heavy oils and tar sands are major players for the future of energy. They represent a massive world resource, at least the size of conventional oils. They are found all over the world but Canada and Venezuela together account, by themselves, for more than half of world deposits. They share the same origin as the lighter conventional oils, but their geological fate drove them into thick, viscous tar-like crude oils. Most of them result from alteration processes mediated by microbial degradation. They are characterized by a low content of lighter cuts and a high content of impurities such as sulfur and nitrogen compounds and metals; so, their production is difficult and deployment of specific processes is required in order to enhance their transportability and to upgrade them into valuable products meeting market needs, and honouring environmental requirements. Although these resources are increasingly becoming commercially producible, less than 1% of total heavy crude oil deposits worldwide are under active development. The voluntarily wide scope of this volume encompasses geology, production, transportation, upgrading, economics and environmental issues of heavy oils. It does not pretend to be exhaustive, but to provide an authoritative view of this very important energy resource. Besides presenting the current status of knowledge and technology involved in exploiting heavy oils, the purpose is to provide an insight into technical, economic and environmental challenges that should be taken up in order to increase the efficiency of production and processing, and finally to give a prospective view of the emerging technologies which will contribute to releasing the immense potential reserves of heavy oil and tar deposits. Contents: Part 1. Heavy Crude Oils.1. Heavy Crude Oils in the Perspective of World Oil Demand. 2. Definitions and Specificities. 3. Geological Origin of Heavy Crude Oils. 4. Properties and composition. Part 2. Reservoir Engineering

  20. Achieving emissions reduction through oil sands cogeneration in Alberta’s deregulated electricity market

    International Nuclear Information System (INIS)

    Ouellette, A.; Rowe, A.; Sopinka, A.; Wild, P.

    2014-01-01

    The province of Alberta faces the challenge of balancing its commitment to reduce CO 2 emissions and the growth of its energy-intensive oil sands industry. Currently, these operations rely on the Alberta electricity system and on-site generation to satisfy their steam and electricity requirements. Most of the on-site generation units produce steam and electricity through the process of cogeneration. It is unclear to what extent new and existing operations will continue to develop cogeneration units or rely on electricity from the Alberta grid to meet their energy requirements in the near future. This study explores the potential for reductions in fuel usage and CO 2 emissions by increasing the penetration of oil sands cogeneration in the provincial generation mixture. EnergyPLAN is used to perform scenario analyses on Alberta’s electricity system in 2030 with a focus on transmission conditions to the oil sands region. The results show that up to 15–24% of CO 2 reductions prescribed by the 2008 Alberta Climate Strategy are possible. Furthermore, the policy implications of these scenarios within a deregulated market are discussed. - Highlights: • High levels of cogeneration in the oil sands significantly reduce the total fuel usage and CO 2 emissions for the province. • Beyond a certain threshold, the emissions reduction intensity per MW of cogeneration installed is reduced. • The cost difference between scenarios is not significant. • Policy which gives an advantage to a particular technology goes against the ideology of a deregulated market. • Alberta will need significant improvements to its transmission system in order for oil sands cogeneration to persist

  1. Process for treating the dialyzed spent liquor from sulphonic acid containing sulfur minerals or tar oils or ammonium salts

    Energy Technology Data Exchange (ETDEWEB)

    Wernicke, E A

    1936-08-09

    Process for working up the dialyzate from sulfonic acid, sulfur-containing mineral or tar oils, or their ammonium salts, characterized by the combination of known steps, in the dialyzate being reacted with alkaline-earth oxide, hydroxide, or carbonate, and the resulting slightly soluble sulfate being filtered off and evaporated if necessary.

  2. Surface and groundwater management in the oil sands industry

    International Nuclear Information System (INIS)

    Dixon, D.G.; Barker, J.

    2004-02-01

    A study was conducted to examine the sublethal effects of oil sands constituents on gill and liver histopathology and fish reproduction. Field studies of food web dynamics were conducted using stable isotopes, including oil sands constituents degradation isotope studies. The objective was to determine changes in food web dynamics associated with reclamation methods and maturity using stable isotopes. The study related changes in toxicity to changes in ground and surface naphthenic acids concentration and composition. It also demonstrated the natural attenuation of toxic chemicals as they travel through groundwater to potential surface water receptors. A methodology was developed to assess the natural attenuation capacity for future situations involving process-affected groundwater of different chemistry with different critical potential contaminants such as sulphides, metals, and specific organics. The mobility and natural attenuation of process water chemicals migrating in groundwater was also assessed. tabs., figs

  3. Geochemical characteristics of oil sands fluid petroleum coke

    International Nuclear Information System (INIS)

    Nesbitt, Jake A.; Lindsay, Matthew B.J.; Chen, Ning

    2017-01-01

    The geochemical characteristics of fluid petroleum coke from the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada were investigated. Continuous core samples were collected to 8 m below surface at several locations (n = 12) from three coke deposits at an active oil sands mine. Bulk elemental analyses revealed the coke composition was dominated by C (84.2 ± 2.3 wt%) and S (6.99 ± 0.26 wt%). Silicon (9210 ± 3000 mg kg"−"1), Al (5980 ± 1200 mg kg"−"1), Fe (4760 ± 1200 mg kg"−"1), and Ti (1380 ± 430 mg kg"−"1) were present in lesser amounts. Vanadium (1280 ± 120 mg kg"−"1) and Ni (230 ± 80 mg kg"−"1) exhibited the highest concentrations among potentially-hazardous minor and trace elements. Sequential extractions revealed potential for release of these metals under field-relevant conditions. Synchrotron powder X-ray diffraction revealed the presence of Si and Ti oxides, organically-complexed V and hydrated Ni sulfate, and provided information about the asphaltenic carbon matrix. X-ray absorption near edge structure (XANES) spectroscopy at the V and Ni K-edges revealed that these metals were largely hosted in porphyrins and similar organic complexes throughout coke grains. Minor differences among measured V and Ni K-edge spectra were largely attributed to slight variations in local coordination of V(IV) and Ni(II) within these organic compounds. However, linear combination fits were improved by including reference spectra for inorganic phases with octahedrally-coordinated V(III) and Ni(II). Sulfur and Fe K-edge XANES confirmed that thiophenic coordination and pyritic-ilmenitic coordination are predominant, respectively. These results provide new information on the geochemical and mineralogical composition of oil sands fluid petroleum coke and improve understanding of potential controls on associated water chemistry. - Highlights: • Oil sands fluid petroleum coke contains wide range of major, minor and

  4. Proceedings of the Infonex oil sands 2005 conference : an industry summit on emerging trends in exploration, production and resource management

    International Nuclear Information System (INIS)

    2005-01-01

    This conference provided a forum to discuss the opportunities and challenges facing the oil sands industry with particular reference to resource characterization and supply and market outlooks to 2015. The driving forces behind oil sands development were also identified. The conference featured 12 presentations that dealt with a range of issues including resource management; operations management; price and cost sharing; emerging transmission pipeline challenges and opportunities; the fiscal regime for oil sands; minimizing the environmental impact of oil sands development; cumulative effects management and the regulatory approval process. An overview of a joint venture by Alberta Environment Northern Region and the Alberta Geological Survey to update existing maps of buried bedrock and drift channels in the oil sands mining and in-situ recoverable areas was included along with an overview of economic and environmental benefits of gasification. A new technology known as multiphase superfine atomized residue (MSAR) as an alternate fuel in oil sands production was discussed along with the issue of bridging the gap between the oil sand industry and First Nations partners. Three of the 12 presentations were catalogued separately for inclusion in this database. tabs., figs

  5. Dynamic simulation of cable shovel specific energy in oil sands excavation

    Energy Technology Data Exchange (ETDEWEB)

    Awuah-Offei, K. [Missouri-Rolla Univ., Rolla, MO (United States). School of Materials, Energy and Earth Resources; Frimpong, S. [Missouri-Rolla Univ., Rolla, MO (United States). Dept. of Mining Engineering, Mining and Nuclear Engineering; Askari-Nasab, H. [Alberta Univ., Edmonton, AB (Canada). School of Mining and Petroleum Engineering

    2005-07-01

    Oil sand excavation requires the use cable shovels which constitute one of the major costs in surface mining operations. Random occurrences of shales and limestones within the Athabasca oil sands formation result in varying shovel diggability and stress loading of the boom-crowd-dipper-teeth assembly which reduces digging efficiency. This inefficient use of cable shovels negatively affects the return on capital investment in these otherwise effective machines. In the Athabasca oil sands, varying stress loading has the potential to increase shovel downtime and increase maintenance costs. This paper presented a newly developed cable shovel simulator that uses shovel kinematics and dynamics, dynamic cutting resistance and payload models. It can model the specific energy needed to overcome the resistance to machine motion and material digging. The comprehensive model considers both machine motion and machine-formation interaction forces. It also provides a comprehensive theoretical assessment of shovel performance. The model is useful to mining engineers when examining both the machine operating parameters and material parameters that influence shovel performance. The study showed that bulk density is the most important material property influencing diggability. Operator preferences also influence the specific energy of excavation. 12 refs., 2 tabs., 6 figs.

  6. Estimation of particle size distribution in Athabasca oil sands by indirect neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schutte, R.; Thompson, G.R.; Donkor, K.K. [New Caledonia College, Prince George, BC (Canada). Dept. of Chemistry; Duke, M.J.M. [Alberta Univ., Edmonton, AB (Canada). SLOWPOKE Nuclear Reactor Facility; Cowles, R. [Syncrude Canada, Edmonton, AB (Canada); Li, X.P.; Kratochvil, B. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemistry

    1999-10-01

    Knowledge concerning the particle size distribution (PSD) of oil sands is necessary for optimal extraction of bitumen from the sand, and it indicates ore quality, gives a measure of process performance during bitumen extraction, and yields information useful for tailings management. Oil sands with mainly coarse particulates are usually bitumen rich and easy to process in the conventional hot water extraction process. These ores do not require the addition of sodium hydroxide as a process aid, and tailings volumes are minimal in contrast to high fines oil sands. Compared to the methods currently in use for determining the PSD in the oil sand industry, a method is described that is rapid, simple to carry out, and does not involve the use of organic solvents with attendant disposal problems. The principle behind the method is the development of a set of correlations by applying regression analysis to a large set of PSD and elemental analysis data. Predicted PSDs compare favorably with results obtained by existing methods. Each of the three PSD methods currently in use could be simulated by the INAA method. The INAA-based model that predicts hydrometer equivalent data was only applicable above certain lower limits for the amount of the fine size fractions present because of the limited sensitivity of the hydrometer method for PSD determination of fine fractions. For all six particle sizes studied, the INAA model had lower overall uncertainty than the corresponding Microtrac and Coulter instrument methods; the instrument repeatability of the INAA fell between those of Microtrac and Coulter. For Athabasca oil sands, the INAA-based method for PSD determination at and below 44 microm afforded results comparable to current Microtrac and Coulter methods. 13 refs., 9 tabs., 2 figs.

  7. Co-occurrence of methanogenesis and N{sub 2} fixation in oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Collins, C.E. Victoria [Department of Renewable Resources, University of Alberta, Edmonton, AB T6G 2G7 (Canada); Foght, Julia M. [Department of Biological Sciences, University of Alberta, Edmonton, AB T6G 2E9 (Canada); Siddique, Tariq, E-mail: tariq.siddique@ualberta.ca [Department of Renewable Resources, University of Alberta, Edmonton, AB T6G 2G7 (Canada)

    2016-09-15

    Oil sands tailings ponds in northern Alberta, Canada have been producing biogenic gases via microbial metabolism of hydrocarbons for decades. Persistent methanogenic activity in tailings ponds without any known replenishment of nutrients such as fixed nitrogen (N) persuaded us to investigate whether N{sub 2} fixation or polyacrylamide (PAM; used as a tailings flocculant) could serve as N sources. Cultures comprising mature fine tailings (MFT) plus methanogenic medium supplemented with or deficient in fixed N were incubated under an N{sub 2} headspace. Some cultures were further amended with citrate, which is used in oil sands processing, as a relevant carbon source, and/or with PAM. After an initial delay, N-deficient cultures with or without PAM produced methane (CH{sub 4}) at the same rate as N-containing cultures, indicating a mechanism of overcoming apparent N-deficiency. Acetylene reduction and {sup 15}N{sub 2} incorporation in all N-deficient cultures (with or without PAM) suggested active N{sub 2} fixation concurrently with methanogenesis but inability to use PAM as a N source. 16S rRNA gene pyrosequencing revealed little difference between archaeal populations regardless of N content. However, bacterial sequences in N-deficient cultures showed enrichment of Hyphomicrobiaceae and Clostridium members that might contain N{sub 2}-fixing species. The results are important in understanding long-term production of biogenic greenhouse gases in oil sands tailings. - Highlights: • Methanogenesis in oil sands tailings can occur under nitrogen depleted conditions. • {sup 15}N{sub 2} isotopic analysis reveals that indigenous microbes can fix N{sub 2} for microbial metabolism and methanogenesis. • 16S rRNA gene analysis suggests that members of Hyphomicrobiaceae and Clostridium may be involved in N{sub 2} fixation. • This is the first report that describes co-occurrence of methanogenesis and nitrogen fixation in oil sands tailings.

  8. Proceedings of the Canadian Institute conference on maximizing oil sands growth : improving transportation logistics, labour supply and pipeline availability

    International Nuclear Information System (INIS)

    2005-01-01

    This conference focused on the development of a transportation infrastructure to accommodate oil sands growth, with particular reference to building a pipeline infrastructure to meet the delivery and supply requirements of oil sands producers. The need for transmission system upgrades and additions to meet the electric power requirements of the oil sands industry was also discussed. The transportation options and new proposed pipeline construction projects that will alleviate the current transportation challenges in the oil sands region were identified. These include the implementation of new infrastructure strategies based on current pipeline availability, Kyoto requirements and downstream market demands. The impact of labour shortages on the oil sands industry was reviewed along with solutions to prevent and overcome these shortages. The conference featured 15 presentations, of which 3 have been catalogued separately for inclusion in this database. tabs., figs

  9. An introduction to conservation and reclamation at Alberta's mineable oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Richens, T. [Alberta Environment, Edmonton, AB (Canada)

    2009-07-01

    This paper presented a balanced view of the conservation and reclamation issues and challenges facing oil sands development in Alberta. Bitumen is recovered by truck and shovel in the shallow oil sands of the Athabasca region. The deeper deposits in the Athabasca, Peace River and Cold Lake regions are accessed primarily using a system of horizontal wells and steam to extract the bitumen from the sand and pump it to the surface. Individual in-situ operations have a smaller environmental impact than mines, and do not produce tailings ponds. However, the footprint of in-situ facilities will accumulate over time because of the potential for extensive future development. The key issues facing conservation and reclamation in the mineable oil sands were discussed. Summary statistics on land disturbed and reclaimed in the region were also provided. The challenges facing reclamation activities include long timeframes; large scale, regional planning and integration; competing land use goals; revegetation; byproduct management; and tailings and process-affected water. Multi-stakeholder forums have proven to be the key to the progression of monitoring, research and development and the sharing of knowledge and information. Frameworks have been developed for the assessment of pre-disturbed and reclaimed soil capability specific to the oil sands region. Additional resources are also available, such as guidelines for the reclamation of terrestrial and wetland habitats that represent the best management practices for reclamation research in revegetation, soil salvage, stockpiling and placement, tailings reclamation, end pit lakes, wetlands and biodiversity. 16 refs., 1 fig.

  10. Watered down : overcoming federal inaction on the impact of oil sands development to water resources

    International Nuclear Information System (INIS)

    Droitsch, D.

    2009-11-01

    The oil sands industry is having a negative impact on Canada's fresh water resources and aquatic ecosystems. Members of the Government of the Northwest Territories (NT) and experts from scientific, non-governmental, and First Nations groups have stated at federal hearings that the federal government must involve itself in the protection of Canada's water resources. This report discussed compelling testimony from recent federal hearings by the House of Commons Standing Committee on Environment and Sustainable Development.The federal government must establish enforceable standards for key toxic substances created by oil sands activity. A water-sharing agreement must be established between Alberta, NT, Saskatchewan, and First Nations governments. Other recommendations included the establishment of a peer-reviewed assessment of the health impacts of industrial oil sands development on First Nations communities; the establishment of cumulative effects assessment procedures; the identification and protection of listed species at risk; and the establishment of proactive measures designed to ensure that oil sands operators pay for the environmental damage caused to water resources. 94 refs., 4 figs.

  11. Oil sands mine pit wall design and performance at Syncrude

    Energy Technology Data Exchange (ETDEWEB)

    Cameron, R.; Danku, M; Purhar, G. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

    2008-07-01

    This study conducted slope stability analyses in order to compare pit performance at an oil sands mine with results from computerized simulations using conventionally known soil parameters. Ranges included fully-drained to fully-saturated piezometric conditions; full-peak strength conditions; fully-softened peak conditions; residual shear strength conditions; and undrained shear strength considerations. Pit wall designs were reviewed and a history of marine clay layers at the mine was presented. Assumed overburden fall-down limits were considered. Shovel overburden slope angles were calculated. An analysis of the review suggested that steeper pit walls provide less room for error and have a higher rate of failures. Incised pleistocene channels, joint and fracture areas as well as higher piezometric level areas also impacted on slope performance. Failed areas influenced ore volumes and led to productivity reductions below 50 per cent. It was concluded that the overburden portions of the oil sands mine ranged between 4H:1V to 5H:1V due to haul roads and the timing of top-bench pushbacks. Future plans for the mine must consider ore inventories, haul road requirements; running surface requirements; and ramping accesses. Future slopes at the oil sands mine will be buttressed with overburden and tailings storage areas, while longer-term slopes will be flattened. 6 refs., 2 tabs., 11 figs.

  12. Catalytic decomposition of tar derived from wood waste pyrolysis using Indonesian low grade iron ore as catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Wicakso, Doni Rahmat [Chemical Engineering Department, Faculty of Engineering, Lambung Mangkurat University, Jalan A. Yani KM. 36 Banjarbaru, 70714, South Kalimantan (Indonesia); Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Sutijan; Rochmadi [Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Budiman, Arief, E-mail: abudiman@ugm.ac.id [Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Center for Energy Studies, Gadjah Mada University, Sekip K1A, Yogyakarta, 55281 (Indonesia)

    2016-06-03

    Low grade iron ore can be used as an alternative catalyst for bio-tar decomposition. Compared to other catalysts, such as Ni, Rd, Ru, Pd and Pt, iron ore is cheaper. The objective of this research was to investigate the effect of using low grade iron ore as catalyst for tar catalytic decomposition in fixed bed reactor. Tar used in this experiment was pyrolysis product of wood waste while the catalyst was Indonesian low grade iron ore. The variables studied were temperatures between 500 – 600 °C and catalyst weight between 0 – 40 gram. The first step, tar was evaporated at 450 °C to produce tar vapor. Then, tar vapor was flowed to fixed bed reactor filled low grade iron ore. Gas and tar vapor from reactor was cooled, then the liquid and uncondensable gas were analyzed by GC/MS. The catalyst, after experiment, was weighed to calculate total carbon deposited into catalyst pores. The results showed that the tar components that were heavy and light hydrocarbon were decomposed and cracked within the iron ore pores to from gases, light hydrocarbon (bio-oil) and carbon, thus decreasing content tar in bio-oil and increasing the total gas product. In conclusion, the more low grade iron ore used as catalyst, the tar content in the liquid decrease, the H{sup 2} productivity increased and calorimetric value of bio-oil increased.

  13. Understanding AL-PAM assisted oil sands tailings treatment

    Energy Technology Data Exchange (ETDEWEB)

    Guo, L.; Maham, Y.; Masliyah, J.; Xu, Z. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

    2010-07-01

    Technologies currently used to treat oil sands tailings include the composite tailings (CT) process and the thickened tailings (TT) or paste technology process. This PowerPoint presentation discussed a flocculation and filtration method used to produce stackable tailings deposits. Magnafloc 1011 and AL-PAM additions were used as part of the filtration technique to produce very dry filter cakes. The effect of AL-PAM molecular weight and aluminum content on tailings treatments was investigated as well as the effect of tailings characteristics on the performance of flocculant-assisted tailings filtration processes. The AL-PAM molecular structure was studied. An experimental study was conducted to determine the effect of various polymer additions on fresh tailings from an oil sands plant. The study showed that the optimum dosage for settling and filtration was lower for higher molecular weight AL-PAM. A higher aluminum content was beneficial for settling. Increases in the aluminum content did not improve filtration rates, but reduced optimal dosages. Step-by-step details of the supernatant filtration process were provided, as well as photographs of the laboratory study. tabs., figs.

  14. Oxidizing oils, etc. [British patent

    Energy Technology Data Exchange (ETDEWEB)

    Penniman, W B.D.

    1926-03-02

    The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tars, and oils containing powdered coal, coke, oreat, sulphur in suspension, by passing air or other oxygen-containing gas through a layer of the material of a depth sufficient substantially to deoxygenate the air and c., is carried out in stages in a series of treatment zones, the pressure in at least one of the zones being above atmospheric pressre. The products of oxidation include acetaldehyde, propionaldehyde, formic, acetic, propionic, butyric, acrylic and phthalic acids, alcohols, acetone, solvents, gums, and substances adapted for use as motor fuels or burnign oils. The oxidizing gas may be enriched with oxygen or be diluted with steam, and its point of entry into the oil and c. layer may be varied to promote or retard settlement of suspended solids.

  15. Dewatering behavior of fine oil sands tailings : A summary of laboratory results

    NARCIS (Netherlands)

    Yao, Y.; van Tol, A.F.; van Paassen, L.A.; Vardon, P.J.; Sego, D.C.; Wilson, G.W.; Beier, N.A.

    2016-01-01

    To evaluate the disposal technology for fine oil sands tailings, the appropriate engineering properties of the tailings should be ascertained. A laboratory study was conducted by Delft University of Technology (the Netherlands) on the geotechnical properties and dewatering behavior of the fine oil

  16. Integrated sulphur management : gas, oil sands, reclamation and the challenges of fluctuating demand

    International Nuclear Information System (INIS)

    Pineau, R.

    2009-01-01

    International Commodities Export Corporation is a privately held company that provides fully integrated service offerings to add maximum value in designing, building, owning, and operating sulphur assets. The company also offers in-house, engineering, procurement and project management, as well as supply management, transportation and distribution services. It also has expertise in marine transportation. This presentation discussed integrated sulphur management, with particular focus on gas, oil sands, reclamation and the challenges of fluctuating demand. The presentation provided an overview of the sulphur market and oil sands sulphur. Key considerations for oil sands producers were also presented. The challenges of fluctuating demand include price and volume considerations; logistics; geography and distance to market; export/offshore versus domestic/United States; seasonal considerations; and an inelastic sulphur market. The presentation concluded with a status update of ICEC's initiative and the advantages of Prince Rupert, an economically viable export infrastructure to producers without onsite forming facilities. figs

  17. Oil sands mining and reclamation cause massive loss of peatland and stored carbon

    Science.gov (United States)

    Rooney, Rebecca C.; Bayley, Suzanne E.; Schindler, David W.

    2012-01-01

    We quantified the wholesale transformation of the boreal landscape by open-pit oil sands mining in Alberta, Canada to evaluate its effect on carbon storage and sequestration. Contrary to claims made in the media, peatland destroyed by open-pit mining will not be restored. Current plans dictate its replacement with upland forest and tailings storage lakes, amounting to the destruction of over 29,500 ha of peatland habitat. Landscape changes caused by currently approved mines will release between 11.4 and 47.3 million metric tons of stored carbon and will reduce carbon sequestration potential by 5,734–7,241 metric tons C/y. These losses have not previously been quantified, and should be included with the already high estimates of carbon emissions from oil sands mining and bitumen upgrading. A fair evaluation of the costs and benefits of oil sands mining requires a rigorous assessment of impacts on natural capital and ecosystem services. PMID:22411786

  18. Impacts and mitigations of in situ bitumen production from Alberta oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Edmunds, Neil

    2010-09-15

    85% or more of Alberta's oil sands is too deep to mine and will be recovered by in situ methods, i.e. from drill holes. This has been made commercially possible through the development in Alberta of Steam Assisted Gravity Drainage (SAGD). Does this impending development threaten the local ecosystem? A quantitative account is given of the principal impacts of in situ oil sands development in Alberta. Impacts on land (habitats), water, and air are considered in terms of local capacity, global benchmarks, and comparisons to alternative renewable technologies. Improvements due to new solvent-additive technology are highlighted.

  19. Ethoxyresorufin-O-deethylase (EROD) induction in rainbow trout exposed to diluted oil sand wastewater

    International Nuclear Information System (INIS)

    Verbeek, A.; Mackay, W.; Birkholz, D.

    1995-01-01

    Toxic industrial wastewaters, such as those from oil sands extraction, must be assessed for their potential sublethal effects before they can be safely disposed in the environment. The induction of ethoxyresorufin-O-deethylase activity was assessed as a potential bioindicator of sublethal stress in rainbow trout exposed to sublethal concentrations of oil sands tailings water. The mixed-function oxygenase system in rainbow trout responded rapidly following a definable concentration-response relationship; however, it proved to be a relatively insensitive indicator of sublethal exposure to oil sands tailings water. Increased activity and maximal induction, as a result of exposure to 0.3 and 0.6 times the LC 50 (Toxic Units), occurred rapidly within 24 hours of exposure. The linearity of the relationship between the concentration of oil sands tailings pond water and ethoxyresorufin-O-deethylase activity, expressed by the following regression equation, In EROD = 3.68 (conc.) + 3.20, had an r 2 value of 0.593. Maximal induction required 0.4--0.8 Toxic Units. The absolute level of maximal induction was only one-fifth to one-sixth of the potential induction as found in response to the positive control, 0.5 mg/kg β-naphthoflavone (i.p.). The authors also present data that suggests that the different levels of induction observed in trout exposed to tailings pond water vs those injected with 0.5 mg/kg β-naphthoflavone (i.p.) may be indicative of two different P450 isoforms, the CYP4Al isoform responding to the organic acidic surfactants in oil sands tailings pond water and the CYP1A1 isoform, the isoform generally associated with most xenobiotic transformation in fish, responding to β-naphthoflavone

  20. Coal Tar and Coal-Tar Pitch

    Science.gov (United States)

    Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

  1. Presentations of the CONRAD Research Symposium : oil sands water usage workshop

    International Nuclear Information System (INIS)

    2004-01-01

    This symposium provided a forum to exchange ideas regarding water use by the oil sands industry in Canada. The topics of discussion addressed timely issues such as corrosion control in pipelines, cumulative discharge modelling in the oil sands area, waste management schemes, the effects of potential limits on water withdrawal for thermal recovery operations and plant operations, the feasibility of geological sequestration of salts, and the impact of process-affected water on bitumen recovery. Other topics of discussion included tailings ponds management, deoxygenation of water, nanofiltration for water management, water quality for wetlands, water reuse, and water supply security. The conference featured 25 presentations, of which 17 have been indexed separately for inclusion in this database. tabs., figs

  2. Phytoremediation of Alberta oil sand tailings using native plants and fungal endophytes

    Science.gov (United States)

    Repas, T.; Germida, J.; Kaminskyj, S.

    2012-04-01

    Fungal endophytes colonize host plants without causing disease. Some endophytes confer plant tolerance to harsh environments. One such endophyte, Trichoderma harzianum strain TSTh20-1, was isolated from a plant growing on Athabasca oil sand tailings. Tailing sands are a high volume waste product from oil sand extraction that the industry is required to remediate. Tailing sands are low in organic carbon and mineral nutrients, and are hydrophobic due to residual polyaromatic hydrocarbons. Typically, tailing sands are remediated by planting young trees in large quantities of mulch plus mineral fertilizer, which is costly and labour intensive. In greenhouse trials, TSTh20-1 supports growth of tomato seedlings on tailing sands without fertilizer. The potential use of TSTh20-1 in combination with native grasses and forbs to remediate under field conditions is being assessed. Twenty-three commercially available plant species are being screened for seed germination and growth on tailing sands in the presence of TSTh20-1. The best candidates from this group will be used in greenhouse and small scale field trials. Potential mechanisms that contribute to endophyte-induced plant growth promotion, such as plant hormone production, stress tolerance, mineral solubilization, and uptake are also being assessed. As well, TSTh20-1 appears to be remarkably frugal in its nutrient requirements and the possibility that this attribute is characteristic of other plant-fungal endophytes from harsh environments is under study.

  3. Low enthalpy geothermal for oil sands (LEGO)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    Geothermal energy is generated by the slow decay of radioactive materials within the Earth. Geothermal energy resources include the water from hot springs used for heating; the withdrawal of high temperature steam from deep wells; and the use of stable ground or water temperatures near the Earth's surface to heat or cool buildings or in industrial processes. Heat pumps are used to transfer heat or water from the ground into buildings in winter. This paper discussed low enthalpy geothermal options for oil sands processes in order to reduce the use of natural gas and emissions from greenhouse gases (GHGs). The study was also conducted to aid in the development of a portfolio of renewable energy options for the oil and gas sector. The study estimated the costs and benefits of operating a shallow geothermal borehole cluster for meeting a portion of process heat demands for the Nexen's Albian mine. The costs and benefits of operating thermo-chillers integrated with a shallow geothermal borehole cluster for waste heat mitigation were also evaluated. The study showed that geothermal designs can be used to meet a portion of oil sands process heat and cooling demands. Mining operators may reduce carbon emissions and energy costs for process heat demands by installing closed loop borehole heat exchangers. Geothermal heat storage capacity can also be used to increase the efficiency of thermal chillers. It was concluded that pilot plant studies would contribute to a better understanding of the technology. tabs., figs.

  4. Mud-farming of fine oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Y.; Tol van, F.; Paassen van, L.; Everts, B.; Mulder, A. [Delft Univ. of Technology, Delft (Netherlands). Dept. of Geotechnology

    2010-07-01

    This PowerPoint presentation discussed an experimental mud-farming technique for fine oil sands tailings. The technique was based on a sub-areal drying technique for dredging sludge developed in the Netherlands for Rotterdam harbour sediments. Between 1960 and 1985, the sludge was deposited in confined disposal sites on land. The sludge was converted to usable clay between 1970 and 1980. The polluted portion of the sludge is stored in a man-made disposal site. The sludge was deposited in thin layers. Stagnant water was then removed. The mud was then dewatered and reused. The sludge was furrowed with amphirol and disc wheels in order to accelerate the ripening process. The dredged material was re-used in a clay factory. The technique was applied to oil sands tailings in order to understand the suction behaviour, sedimentation behaviour, and precipitation deficit of the tailings. State changes of the sludge were monitored. No clear sedimentation phase was identified prior to consolidation. A comparison of material properties showed that the total amount of water to be extracted was more than the Rotterdam sludge, but the suction behaviour was similar. The precipitation deficit from mid-April until September will require a customized deposition strategy. Details and photographs of the experimental studies were included. tabs., figs.

  5. Evaluation of natural attenuation processes in the groundwater of a tar oil contaminated site: development of a monitoring network

    International Nuclear Information System (INIS)

    Borke, P.; Husers, N.; Werner, P.; Leibenath, C.

    2005-01-01

    Tar oil is a complex mixture of mainly aromatic hydrocarbons. It is found in the subsurface of manufactured gas plants (MGP), coking plants or wood preserving facilities. The transportation into the soil and groundwater stands for a severe contamination. This is due to the physico-chemical properties of the DNAPL (dense non aqueous phase liquid) and its mobility in the soil and aquifer system. Additionally most of the contaminants show a low biological degradability and solubility under in situ conditions. Therefore it is known as a long term source of contamination. Nevertheless, natural attenuation (NA) processes are detectable at tar oil contaminated sites. In the thematic network two of the German funding priority KORA (http://www.natural-attenuation.de) these processes are matter of investigation. Four typical contaminated sites were chosen to evaluate under which circumstances monitored natural attenuation (MNA) is applicable. Furthermore enhanced natural attenuation questions are examined. The design of monitoring networks at tar oil contaminated sites plays a significant role in gaining field evidence for natural attenuation as well as documenting the efficiency of the attenuation processes and evaluating the matching of performance goals. Well designed monitoring networks include the placement of monitoring wells in 3D so that 3D flow path, mass balances and an estimation of mass flux can be monitored. As an example the history of the monitoring network of a wood preserving facility is shown. Starting from a risk assessment network to a network for MNA is presented. In this case for example especially the determination of the groundwater flow direction in time and space is connected to the number of observation wells and their location. Moreover in the beginning the observation wells were located according to the assumed centerline of the plume. Because of the variability of the groundwater flow direction and the need to determine mass flux a control plane

  6. Fish gill responses to pollutants from oil sands mining-associated waters

    International Nuclear Information System (INIS)

    Lee, L.E.J.; Willfang, S.; Lamb, M.P.; Nero, V.; Farwell, A.J.; Dixon, D.G.

    2002-01-01

    The processing of Athabasca Deposit oil sands results in large amounts of liquid wastes associated with oil sand tailings. In addition to containing polycyclic aromatic hydrocarbons (PAHs), these waste waters are high in salinity and naphthenic acids which may be toxic to aquatic biota and their effects must be clarified. This study presents a suite of tests for in-depth and quick analysis of tailings water toxicity and contributes to the assessment of environmental risk. Yellow perch, fathead minnows, and rainbow trout were exposed to reclamation ponds where both in vivo and in vitro evaluation of crude and individual naphthenic acids and salts were conducted to examine their effect on fish gills which are very susceptible to contaminants. The fish exposed to the reclamation ponds showed higher incidence of gill pathological changes than control fish in Mildred Lake, a reservoir lake whose waters are diverted for use in oil sands extraction. Notable gill histopathological changes were observed when fish were exposed in vivo to sulfate/chloride salts and to abietic acid. Changes in membrane integrity, lysosomal activity and general morphology were observed when fished were exposed in vitro to salts, commercial napthenic acids or crude naphthenic extracts from the reclamation ponds

  7. Ambient air quality observations in the Athabasca oil sands region

    International Nuclear Information System (INIS)

    1996-01-01

    Both Syncrude and Suncor have plans to develop new oil sands leases and to increase crude oil and bitumen recovery in the Athabasca oil sands region. In recognition of the effects that this will have on the environment, Suncor has proposed modifications to reduce SO 2 emissions to the atmosphere, while Syncrude plans to develop additional ambient air quality, sulphur deposition and biomonitoring programs. This report discussed the ambient air quality monitoring that was undertaken in the Fort McMurray-Fort McKay airshed. Twelve continuous ambient air quality stations and 76 passive monitoring stations are maintained in the region. Environment Canada maintains eight precipitation monitoring stations in northern Alberta and Saskatchewan. Source characterization, ambient air quality and meteorology observations, air quality monitoring, and air quality data from continuous sulphur dioxide, hydrogen sulphide, nitrogen oxides, ozone, carbon monoxide, hydrocarbon, acid rain and particulates analyzers were reviewed. The documentation of all computer files used for the analysis of the air quality data is discussed in the Appendix. 47 refs., 39 tabs., 53 figs

  8. Application of organic geochemistry to coastal tar residues from central California

    Energy Technology Data Exchange (ETDEWEB)

    Kvenvolden, K.A.; Rosenbauer, R.J.; Hostettler, F.D.; Lorenson, T.D.

    2000-01-01

    Tar residues are common on the Monterey Bay National Marine Sanctuary. These coastal tar residues have been washed ashore and usually occur on headlands near the high-tide line. In this study, 18 coastal tar residues were collected and analyzed to determine their carbon isotopic compositions and values of selected biomarker ratios. All of the residues have very heavy ({sup 13}C-enriched) carbon isotopic compositions spanning a narrow range ({delta}{sup 13}C = {minus}22.2 to {minus}23.4{per{underscore}thousand}), and 28,30-bisnorhopane is present in all samples. These same geochemical characteristics are found in Monterey Formation oils from which the coastal tar residues were likely derived. These coastal residues could result from natural seeps or from accidental spills. Statistically the coastal tar residues can be organized into three groups, each of which may represent different spill or seep events. Seven samples of potential local representative sources for the tar residues were examined, but none could account for the coastal tars.

  9. Prediction of critical transport velocity for preventing sand deposition in gas-oil multiphase production and well systems

    Energy Technology Data Exchange (ETDEWEB)

    Bello, O.O.; Reinicke, K.M. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. of Petroleum Engineering; Teodoriu, C. [Texas A and M Univ., College Station, TX (United States). Dept. of Petroleum Engineering

    2008-10-23

    The critical transport velocity is one of the key parameters for gas-oil-sand multiphase production and well system design and safe operation. Existing American Petroleum Institute Recommended Practice 14E (API RP 14E) for the sizing of multiphase flow systems suggests an equation to calculate threshold transport velocity. This equation only considers mixture density and does not account for factors such as fluid properties, gas-liquid flow patterns, sand loading, sand particle size, size distributions, shape factor and density. This work presents an improved computational methodology, which can be applied to estimate the critical transport velocity required to ensure efficient performance of gas-oil-sand multiphase production and well systems. The improved method is based on the modelling of three-phase gas-oil-sand pipe flow physics from first principle. Computations of the critical transport velocities show reasonable agreement with values calculated from mechanistic model (Danielson, 2007) for a relatively wide range of design and operating conditions. Compared with the mechanistic model (Danielson, 2007), the present method has no imposed limitations to the range of applicability. It is also takes into adequate account the effects of operating pressure, flow geometry, sand particle size, size distribution and shape factor, which have considerable influence on the critical transport velocity in gas-oil-sand multiphase production and well systems. (orig.)

  10. Recovery of naphthalene, anthracene, etc. , from tar

    Energy Technology Data Exchange (ETDEWEB)

    1920-12-25

    A process is described for the recovery of naphthalene, anthracene, and the like from tar oils and similar liquors, characterized in that the oil is treated in a rapidly rotating hammer mill, such as a colloid mill, with water sufficient, in the presence or absence of suitable solvents, for the only portion preferably in the presence of emulsifiers; and is filtered through a filter with fine pores.

  11. Bitumen extraction from oil sands ore-water slurry using CaO (lime) and or ozone

    Energy Technology Data Exchange (ETDEWEB)

    Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada); Burkus, Z.; Moschopedis, S.E.; Ozum, B. [Apex Engineering Inc., Calvert City, KY (United States)

    2008-10-15

    Reductions in the surface and interfacial tensions in oil sands ore-water slurry systems improve bitumen extraction processes from oil sands ore structures and promote the attachment of air bubbles to liberated bitumen droplets. This study provided details of a non-caustic bitumen extraction process where oil sands slurries were conditioned by bitumen asphaltenes modified to act as surfactants. Oil sands ore-water slurry extraction processes were optimized by adding lime (CaO) and oxidizing bitumen asphaltenes with ozone (O{sub 3}). Experiments were conducted using oil sands ore and process water samples from Alberta. Extraction tests were performed to investigate the effects of various CaO and O{sub 3} dosages and treatment retention times on bitumen extraction efficiency on operating temperatures of 20, 35 and 50 degrees C. A Dean-Stark extraction apparatus was used to determine the amount of bitumen contained in the ore, froth, and in left-over tailings. Process water and release water chemistry were also monitored. Bitumen extraction efficiency was defined as the percentage of bitumen recovered in the resulting froth. Use of the slurries allowed high extraction efficiencies at a temperature of 35 degrees C. Energy consumption and carbon dioxide (CO{sub 2}) emissions were also reduced. The study showed that both additions resulted in significant improvements in bitumen extraction efficiency. Use of the technique also eliminated the accumulation of Na{sup +} ions in produced water. It was concluded that further tests are needed in order to commercialize the CaO and O{sub 3} based techniques. 14 refs., 1 tab., 4 figs.

  12. Effects of oil sands effluent on cattail and clover: photosynthesis and the level of stress proteins

    Energy Technology Data Exchange (ETDEWEB)

    Crowe, A.U.; Han, B.; Kermode, A.R.; Bendell-Young, L.I.; Plant, A.L. [Simon Fraser University, Burnaby (Canada). Dept. of Biological Sciences

    2001-07-01

    The oil sands industry located in northeastern Alberta, Canada, generates large volumes of effluent characterized by a high level of dissolved ions and naphthenic acids. The dikes used to store the effluent seep, creating wetlands which are subsequently invaded by obligate wetland flora such as cattail (Typha latifolia L.). The appearance of these wetlands prompted the oil sands industry to consider wetlands as part of their reclamation strategy. However, to ensure long-term viability of such wetlands, the response of the flora to the industrial effluent needed to be determined. To this end, apparent photosynthesis (APS), the level of ribulose-1,5-bisphosphate carboxylase (RuBisCo) large subunit, dehydrin-related polypeptides, and protein disulphide isomerase (PDI) were evaluated in cattail and alsike clover plants (Trifolium hybridum L.) exposed to the oil sands effluent. APS measured in plants impacted by oil sands effluent was significantly higher than that of plants in the non-impacted off-site location. Among the on-site locations, plants growing in the natural wetlands site had higher APS compared to all other sites. The level of RuBisCo was not increased in cattail or clover growing in effluent-contaminated sites indicating that enhanced photosynthesis was not due to greater levels of this enzyme. Dehydrin-related polypeptides were detected only in the roots of cattail and were absent in clover. The polypeptide profile was altered in cattail exposed to oil sands effluent indicating that they were responding to an osmotic stress. The level of PDI was unaffected in the leaves of cattail regardless of the nature of the effluent to which they were exposed. Overall, the data indicate that cattail and clover are adapted to the oil sands effluent, although further studies are needed to assess their long-term ability to survive in the presence of this anthropogenic stress. (Author)

  13. Conservation and reclamation at Alberta's mineable oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Purdy, B.; Richens, T. [Alberta Environment, Edmonton, AB (Canada)

    2010-07-01

    The regulatory foundation for oil sands in this region is established by the Energy Resources Conservation Board, Environmental Protection and Enhancement Act (EPEA), as well as the Water Act. This presentation discussed the regulatory foundation for conservation and reclamation in the mineable oil sands region. EPEA requirements and conservation objectives were identified. EPEA conservation and reclamation requirements stipulate that an operator must conserve and reclaim and obtain a reclamation certificate. EPEA approvals that were presented compared prescriptive standards versus meeting outcomes at certification. Operational and management challenges as well as the role of research networks and multi-stakeholder organizations were also addressed. Challenge facing the industry include progressive reclamation; tailings management and process-affected water; reclamation certification; integrated landscapes; soil handling and revegetation and monitoring and research. The presentation demonstrated that reclamation begins with mine planning and ends with certification. figs.

  14. Quality controlled water, sediment, tissue, and tar/oil chemistry analyses from the Deepwater Horizon (DWH) oil spill event in the Gulf of Mexico from 2010-04 to 2011-06, sourced from NOAA's Query Manager data management system (NODC Accession 0108924)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This collection includes 4 data files (one each for water, sediment, tissue, and tar/oil analyses) containing data from the Deepwater Horizon (DWH) Oil Spill Event...

  15. Parameters and mechanisms in the mechanical upgrading of Athabasca oil sands by a cold water process

    Energy Technology Data Exchange (ETDEWEB)

    Grant, G B

    1977-01-01

    The efficiency of sand rejection in the cold water mechanical upgrading of Athabasca oil sands has been studied in the operation of rotary contactors of 8.9 cm and 19.0 cm internal diameter, fitted with lifters. Duration of operation, rate of rotation, linear velocity of lifters, temperature, water to oil sands ratio, depth of charge to lifter height ratio, and internal diameter of the contactor have been identified as important parameters. Surfactant addition and presoaking of the feed had negligible effects on the process. A model has been proposed that accounts for the variation of extraction efficiency as a function of duration of operation, the data showing that both the equilibrium extraction efficiency and the rate constant were greater in the large contactor than the small contactor for equal rates of rotation, except when centrifuging occurred in the large contactor. Sand rejection was promoted by lifter-sand and contactor wall-sand impacts and by the action of shear fields within vortices created by the lifter. The impacts occurred for all loading conditions but the latter mechanism only contributed to the sand rejection process for depth-of-charge to lifter height ratios of one or greater. In addition, the contribution of shear fields was only significant for large water to oil sands ratios. Finally, the sand rejection process was affected significantly by variations in temperature. 37 refs., 34 figs., 11 tabs., 4 illus.

  16. Peak oil and gas

    International Nuclear Information System (INIS)

    Ziegler, W. H.; Campbell, C. J.; Zagar, J.J.

    2009-01-01

    Oil and gas were formed under exceptional conditions in the geological past, meaning that they are subject to natural depletion, such that the past growth in production must give way to decline. Although depletion is a simple concept to grasp, public data on the resource base are extremely unreliable due to ambiguous definitions and lax reporting. The oil industry is reluctant to admit to an onset of decline carrying obvious adverse financial consequences. There are several different categories of oil and gas, from tar sands to deep water fields, each with specific characteristics that need to be evaluated. It is important to build a global model on a country by country basis in order that anomalous statistics may be identified and evaluated. Such a study suggests that the world faces the onset of decline, with far-reaching consequences given the central role of oil-based energy. It is accordingly an important subject deserving detailed consideration by policy makers. (author)

  17. Royal Society of Canada expert panel report : environmental and health impacts of Canada's oil sands industry

    International Nuclear Information System (INIS)

    Gosselin, P.; Hrudey, S.E.; Naeth, M.A.; Plourde, A.; Therrien, R.; Laval Univ., Quebec City, PQ; Van Der Kraak, G.; Guelph Univ., ON; Xu, Z.

    2010-12-01

    This expert panel report was commissioned by the Royal Society of Canada to provide a comprehensive evidence-based assessment of the environmental and health impacts of Canada's oil sands industry. The report evaluated the feasibility of land reclamation and the impacts of oil sands contaminants on downstream residents. Health impacts on residents living in the Regional Municipality of Wood Buffalo were assessed, and the impacts on regional water supplies were evaluated. Regional water and ground water quantities were examined, and issues related to tailing pond operations and reclamation were examined. Ambient air quality impacts were assessed, as well as potential impacts of the oil sands industry on greenhouse gas (GHG) emissions. The environmental regulatory performance of operators in the industry was also evaluated. A summary of economic and policy issues related to the industry was also provided. The study identified major gaps in the process of assessment, prevention, and mitigation of the health impacts of oil sands exploitation, as as major indirect health impacts linked to past exploitation activities. 672 refs., 11 tabs., 11 figs. 10 appendices.

  18. Cultural keystone species in oil sands reclamation, Fort McKay, Alberta, Canada

    Energy Technology Data Exchange (ETDEWEB)

    Garibaldi, A.; Straker, J. [Stantec Consulting Ltd., Surrey, BC (Canada)

    2009-12-15

    This presentation discussed a reclamation project conducted in Fort McKay, Alberta that was designed to address some of the social and cultural concerns related to oil sands mining in the region. Conventional reclamation practices in the region have demonstrated a lack of communication and participation from surrounding communities. The project was designed to address future land use plans and to include cultural values in the reclamation process. An integrative approach was used to address community landscapes issues and to explore methods of reclaiming the social and ecological components impacted by oil sands development. Traditional environmental knowledge was also incorporated into the program's design. Cultural keystone species (CKS) were used to provide a culturally relevant compass to guide people engaging in long-term reclamation and land use planning. Cultural keystone species were defined as salient species that significantly shape the cultural identity of a people. Keystone species in the region include the beaver; the moose; the ratroot; and cranberries and blueberries. Challenges to the program included the fact that the scale of oil sands disturbances are so immense that some community recommendations for reclaiming CKS may be impractical. tabs., figs.

  19. Groundwater recharge estimates in the Athabasca and Cold Lake oil sands areas

    International Nuclear Information System (INIS)

    MacMillan, G.J.; Smith, A.D.

    2009-01-01

    Groundwater recharge estimates for the Cold Lake and Athabasca oil sands region were presented. New oil sands projects planned for the future will require approximately 150,000 m 3 per day of groundwater. Regulators and public agencies are now investigating the potential impacts of oil sands operations on both shallow groundwater and surface water in the region. Maximum yields from the aquifers are also being estimated. Measurements are currently being taken to determine transmissivity, hydraulic pressure, storage potential and leakage. Numerical models are currently used to determine saturated zone recharge estimates and water table fluctuations. Isotope tracers are also being used to determine where groundwater flow potential is vertical as well as to determine correction factors for hydrogeological and geochemical conditions at each site. Darcy's Law is used to determine heat flow in the groundwater aquifers. To date, the studies have demonstrated that drilling fluids have been recovered at groundwater sites. Wells are often installed near water supply and supply well networks. It was concluded that new water wells will need to be completed at various depths. Data were presented for aquifers and nest wells. refs., tabs., figs

  20. Oil sands geologists in an industry-school partnership : a resource and teaching opportunity

    International Nuclear Information System (INIS)

    Dudley, J.S.; Doram, T.

    1999-01-01

    The province of Alberta has developed a credit course within their Career and Technology Studies Program on the earth science of oil sands for senior high school science students. The course helps students learn to apply basic sciences to earth science through workplace site visits, resource material and team work. This paper described the increasing demand for, and success of, industry-high school partnerships, and provided special emphasis on the Bowness Senior High School-Imperial Oil partnership in Calgary, Alberta. Imperial Oil Resources is a major producer of oil sands and an employer of earth scientists in a variety of careers in which a wide range of technologies is applied. Students enrolled in the credit study program visit the Imperial Oil Resources Research Centre on five different occasions to gain skills and qualities sought by the workplace including communication, adaptability, team work, and science literacy and its application. 9 refs., 1 tab., 2 figs

  1. Copyrolysis of coal with coke-oven gas. III. Analysis of tar

    Energy Technology Data Exchange (ETDEWEB)

    Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

    1998-02-01

    Tars from copyrolysis of Xianfeng lignite with coke-oven gas (COG) at different pressures (0.1-5 MPa) and heating rates (5-25{degree}C/min) to a final temperature of 650{degree}C were analyzed and compared with hydropyrolysis under the same H{sub 2} partial pressure. The results indicated that high contents of BTX, PCX and naphthalene were found in the tar from copyrolysis of Xianfeng lignite with COG. Pressure and heating rate have important effects on tar yields and the contents of BTX, PCX and naphthalene in oil. Increasing pressure and decreasing heating rate enhance the tar yields and result in high yields of BTX and PCX. When compared with hydropyrolysis under the same H{sub 2} partial pressure, the tar yield increases by 1.2 times and the yields of BTX, PCX and naphthalene by about 1.6, 1.3 and 1.6 times, respectively. At the same total pressure (3MPa), the yields of BTX and naphthalene from copyrolysis are equal to those from hydropyrolysis. The results reveal that other components in COG, such as methane, carbon monoxide etc., are of importance for pyrolysis behaviour of coal under COG and improvement of oil qualities. 5 refs., 5 figs., 2 tabs.

  2. Adsorption of surfactants on sand surface in enhanced oil recovery: Isotherms, kinetics and thermodynamic studies

    Energy Technology Data Exchange (ETDEWEB)

    Bera, Achinta; Kumar, T.; Ojha, Keka; Mandal, Ajay, E-mail: mandal_ajay@hotmail.com

    2013-11-01

    Adsorption of surfactants onto reservoir rock surface may result in the loss and reduction of their concentrations in surfactant flooding, which may render them less efficient or ineffective in practical applications of enhanced oil recovery (EOR) techniques. Surfactant flooding for EOR received attraction due to its ability to increase the displacement efficiency by lowering the interfacial tension between oil and water and mobilizing the residual oil. This article highlights the adsorption of surfactants onto sand surface with variation of different influencing factors. It has been experimentally found that adsorption of cationic surfactant on sand surface is more and less for anionic surfactant, while non-ionic surfactant shows intermediate behaviour. X-ray diffraction (XRD) study of clean sand particles has been made to determine the main component present in the sand particles. The interaction between sand particles and surfactant has been studied by Fourier Transform Infrared (FTIR) Spectroscopy of the sand particles before and after aging with surfactant. Salinity plays an important role in adsorption of anionic surfactant. Batch experiments were also performed to understand the effects of pH and adsorbent dose on the sorption efficiency. The sand particles exhibited high adsorption efficiency at low pH for anionic and nonionic surfactants. But opposite trend was found for cationic surfactant. Adsorption data were analyzed by fitting with Langmuir, Freundlich, Redlich-Peterson, and Sips isotherm models. Results show that the Langmuir isotherm and pseudo-second order kinetics models suit the equilibrium and kinetics of adsorption on sand surface. Thermodynamics feasibility of the adsorption process was also studied to verify the spontaneity of the process.

  3. Reclamation and closure of an oil sands tailings facility

    Energy Technology Data Exchange (ETDEWEB)

    Sobkowicz, J. [Thurber Engineering Ltd., Calgary, AB (Canada); Morgenstern, N. [Alberta Univ., Edmonton, AB (Canada)

    2010-07-01

    This PowerPoint presentation discussed methods of ensuring the successful reclamation of oil sands tailings facilities. Tailings should be reclaimed as mining proceeds in order to avoid an excessive accumulation of fluid fine tailings (FFT). The volume of mature fine tailings (MFT) in ponds should be limited in order to ensure effective tailings management. The reclaimed landforms should have good geotechnical stability and be comprised of self-sustaining native vegetation. Strength is needed to allow for timely capping and initial reclamation, and stiffness is required to minimize future settlement and to allow for the construction of a closure landscape. Reclamation strategies were presented for fines-dominated tailings; sand-depleted tailings; and sand-dominated tailings. Energy Resources Conservation Board (ERCB) criteria for tailings reclamation were discussed, and various monitoring and performance assessment strategies were presented. tabs., figs.

  4. Papers of the Canadian Institute's 3. annual conference : oil sands supply and infrastructure : labour supply, upgraders, transportation, pipelines

    International Nuclear Information System (INIS)

    2005-01-01

    The focus of this conference was on the development of the oil sands industry, with specific reference to issues concerning supply and infrastructure. Energy source development and transmission issues were discussed, as well as transportation systems. The impact of increased oil sands development on pipelines was also examined. Various fuel options were discussed, including the use of hydrogen, natural gas and alternate fuels in manufacturing and processing plants. Economic drivers and the creation of new markets were examined, and various export opportunities were reviewed. The environmental impact of increased oil sands activity was discussed, with specific reference to the Boreal regions. Management challenges in the oil sands industry were also discussed along with issues concerning human resources, labour supply, training and education. The conference featured 15 presentations, of which 13 have been catalogued separately for inclusion in this database. refs., tabs., figs

  5. Application of forward osmosis membrane technology for oil sands process-affected water desalination.

    Science.gov (United States)

    Jiang, Yaxin; Liang, Jiaming; Liu, Yang

    2016-01-01

    The extraction process used to obtain bitumen from the oil sands produces large volumes of oil sands process-affected water (OSPW). As a newly emerging desalination technology, forward osmosis (FO) has shown great promise in saving electrical power requirements, increasing water recovery, and minimizing brine discharge. With the support of this funding, a FO system was constructed using a cellulose triacetate FO membrane to test the feasibility of OSPW desalination and contaminant removal. The FO systems were optimized using different types and concentrations of draw solution. The FO system using 4 M NH4HCO3 as a draw solution achieved 85% water recovery from OSPW, and 80 to 100% contaminant rejection for most metals and ions. A water backwash cleaning method was applied to clean the fouled membrane, and the cleaned membrane achieved 77% water recovery, a performance comparable to that of new FO membranes. This suggests that the membrane fouling was reversible. The FO system developed in this project provides a novel and energy efficient strategy to remediate the tailings waters generated by oil sands bitumen extraction and processing.

  6. Evaluation of heavy-oil and tar sands in Bourbon, Crawford, and Cherokee Counties, Kansas. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ebanks, W.J. Jr.; James, G.W.; Livingston, N.D.

    1977-12-01

    The current national energy-resource situation has provided the incentive to investigate more fully deposits of heavy-oil bearing sandstone in southeastern Kansas, as part of a larger, three-state study. The results of this study indicate that the size of the heavy-oil resource in the three Kansas counties studied is smaller than earlier estimates suggested. A resource of 200 to 225 million barrels of oil in-place is estimated to be present in areas of ''known oil occurrence,'' as established by this study. The amount of this in-place resource which may be considered to be reserves, that is, recoverable under existing technology and economics, is zero. The estimates of resource-size are severely downgraded from earlier estimates mainly because of the discontinuous nature of the potential reservoir sandstone bodies and because of the thinness and shaliness of some of these sandstones. The earlier impression of these heavy-oil reservoirs, at least in Kansas, as being widespread, heavily oil saturated, ''blanket'' sandstones unfortunately is not correct. There are areas, shown on maps, which may warrant further investigation because of locally good oil-saturation, i.e., more than 400 barrels per acre foot, in trends of sandstone thicker than 20 feet. It is concluded that there will be no widespread exploitation of subsurface heavy-oil sandstones within the areas of Bourbon, Crawford, and Cherokee Counties, Kansas. Smaller areas indicated here may warrant further drilling and investigation, but the potential size of the heavy-oil resource is severely downgraded from earlier estimates.

  7. Energy infrastructure modeling for the oil sands industry: Current situation

    International Nuclear Information System (INIS)

    Lazzaroni, Edoardo Filippo; Elsholkami, Mohamed; Arbiv, Itai; Martelli, Emanuele; Elkamel, Ali; Fowler, Michael

    2016-01-01

    Highlights: • A simulation-based modelling of energy demands of oil sands operations is proposed. • Aspen simulations used to simulate delayed coking-based upgrading of bitumen. • The energy infrastructure is simulated using Aspen Plus achieving self-sufficiency. • Various scenarios affecting energy demand intensities are investigated. • Energy and CO_2 emission intensities of integrated SAGD/upgrading are estimated. - Abstract: In this study, the total energy requirements associated with the production of bitumen from oil sands and its upgrading to synthetic crude oil (SCO) are modeled and quantified. The production scheme considered is based on the commercially applied steam assisted gravity drainage (SAGD) for bitumen extraction and delayed coking for bitumen upgrading. In addition, the model quantifies the greenhouse gas (GHG) emissions associated with the production of energy required for these operations from technologies utilized in the currently existing oil sands energy infrastructure. The model is based on fundamental engineering principles, and Aspen HYSYS and Aspen Plus simulations. The energy demand results are expressed in terms of heat, power, hydrogen, and process fuel consumption rates for SAGD extraction and bitumen upgrading. Based on the model’s output, a range of overall energy and emission intensity factors are estimated for a bitumen production rate of 112,500 BPD (or 93,272 BPD of SCO), which were determined to be 262.5–368.5 MJ/GJ_S_C_O and 14.17–19.84 gCO_2/MJ_S_C_O, respectively. The results of the model indicate that the majority of GHG emissions are generated during SAGD extraction (up to 60% of total emissions) due to the combustion of natural gas for steam production, and the steam-to-oil ratio is a major parameter affecting total GHG emissions. The developed model can be utilized as a tool to predict the energy demand requirements for integrated SAGD/upgrading projects under different operating conditions, and

  8. Threshold Considerations and Wetland Reclamation in Alberta's Mineable Oil Sands

    Directory of Open Access Journals (Sweden)

    Lee Foote

    2012-03-01

    Full Text Available Oil sand extraction in Alberta, Canada is a multibillion dollar industry operating over 143 km² of open pit mining and 4600 km² of other bitumen strata in northern boreal forests. Oil production contributes to Canada-wide GDP, creates socio-cultural problems, provides energy exports and employment, and carries environmental risks regarding long-term reclamation uncertainties. Of particular concern are the implications for wetlands and water supply management. Mining of oil sands is very attractive because proven reserves of known quality occur in an accessible, politically stable environment with existing infrastructure and an estimated 5.5 billion extractable barrels to be mined over the next five decades. Extraction occurs under a set of limiting factors or thresholds including: limited social tolerance at local to international levels for externalities of oil sand production; water demands > availability; limited natural gas supplies for oil processing leading to proposals for hydroelectric dams and nuclear reactors to be constructed; difficulties in reclaiming sufficient habitat area to replace those lost. Replacement of the 85 km² of peat-forming wetlands forecast to be destroyed appears unlikely. Over 840 billion liters of toxic fluid byproducts are currently held in 170 km² of open reservoirs without any known process to purify this water in meaningful time frames even as some of it leaches into adjacent lands and rivers. Costs for wetland reclamation are high with estimates of $4 to $13 billion, or about 6% of the net profits generated from mining those sites. This raises a social equity question of how much reclamation is appropriate. Time frames for economic, political, and ecological actions are not well aligned. Local people on or near mine sites have had to change their area use for decades and have been affected by industrial development. Examining mining effects to estimate thresholds of biophysical realities, time scales

  9. Oil sands tailings leachability and toxicity evaluation

    International Nuclear Information System (INIS)

    Gulley, J.R.

    1995-01-01

    Fine tailings disposal and reclamation is a major issue facing the oil sands mining and extraction industry. Government regulations dictate that reclamation must return the site to a level of self-sustaining biological capability which approximates the natural condition. A two-phase laboratory program has been completed to investigate the suitability of alternative reclamation materials. For the first phase of the study, chemical and toxicological analyses were carried out on 13 different reclamation and reference materials (solid phase and extractions). Seedling emergence, nematode maturation, algal growth and bacterial luminescence for leachate samples showed a range of sensitivities in response to the tested materials, although phytotoxicity tests were generally the most sensitive. With the exception of one test material, high toxicity ratings were consistent with that expected from the chemical data. The second phase of the study focused on the evaluation of chemical and toxicological conditions in leachate water generated using bench-scale column percolation tests. Leachate water equivalent to 10 pore volume replacements was generated and temporal variations in toxicity and chemistry monitored. Similar to phase 1 findings, phytotoxicity tests were the most sensitive tests to leachate waters. For most materials tested, most toxicity was removed after 2--3 porewater replacements. More persistent toxicity was noted for samples containing bitumen (e.g., fine tails and oil sands). No clear correspondence was noted between chemical concentrations and toxicity in leachate waters

  10. Recent advancements in the geotechnical characterization of oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, J. [Conetec, Richmond, BC (Canada)

    2010-07-01

    The technical aspects of soft oil sands tailings in-situ geotechnical site investigations were discussed. Geotechnical studies are conducted to determine containment structure stability as well as to determine volumetric and mass balances. The results of the studies are used in tailings management plans and construction activities. Flow penetrometers, field vane shear tests, and Gamma-CPTu tests are used in in-situ oil sands tailings geotechnical studies in order to determine pore pressure dissipation, and measure shear strength. Ball penetration tests are conducted to determine tailings strength. Methods of interpreting data from the tests were presented, and data from the tests were also compared and evaluated. Recommended procedures for strength screening were presented. Statistical methods for determining tailings behaviour types were outlined. The study showed that Gamma-CPTu data can be used to obtain reasonable preliminary estimates of solids and fines when combined with tailings behaviour type analyses. tabs., figs.

  11. Acid Tar Lagoons: Management and Recovery

    Science.gov (United States)

    Bohers, Anna; Hroncová, Emília; Ladomerský, Juraj

    2017-04-01

    This contribution presents the issue with possibility of definitive removal of dangerous environmental burden in Slovakia - serious historical problem of two acid tar lagoons. In relation to their removal, no technology has been found so far - technologically and economically suitable, what caused problems with its management. Locality Predajná is well known in Slovakia by its character of contrasts: it is situated in the picturesque landscape of National Park buffer zone of Nízke Tatry, on the other site it is contaminated by 229 211m3 of acid tar with its characteristics of toxicity, carcinogenicity, teratogenicity, mutagenicity and toxicity especially for animals and plants. Acid tar in two landfills with depth of 1m in case of the first lagoon and 9,5m in case of the second lagoon is a waste product derived from operation of Petrochema Dubová - refinery and petrochemical plant whose activity was to process the crude oil through processes of sulfonation and adsorption technology for producing lubricating and special oils, synthetic detergents and special white oils for cosmetic and medical purposes. A part of acid tar was incinerated in two incineration plats. Concentration of SO2 in combustion gases was too high and it was not possible to decrease it under the value of 2000 mg.mn-3 [LADOMERSKÝ, J. - SAMEŠOVÁ, D.: Reduction in sulfur dioxide emissions waste gases of incineration plant. Acta facultatis ecologiae. 1999, p. 217-223]. That is why it was necessary to put them out of operation. Later, because of public opposition it was not possible to build a new incineration plat corresponding to the state of the art. Even though actual Slovak and European legislative for protection of environment against such impacts, neither of tried methods - bio or non-biologic treatment methods - was proved as suitable for processing or for recovery in the reason of different factors admission: i.e. strong aggressivity, difficulty with handling because of its sludgy and

  12. Characterization of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) in tar-balls collected from the East Coast of Peninsular Malaysia.

    Science.gov (United States)

    Chandru, Kuhan; Zakaria, Mohamad Pauzi; Anita, Sofia; Shahbazi, Azadeh; Sakari, Mahyar; Bahry, Pourya Shahpoury; Mohamed, Che Abd Rahim

    2008-05-01

    The East Coast of Peninsular Malaysia faces the South China Sea and is vulnerable to oil pollution because of intense petroleum production activities in the area. The South China Sea is also a favored route for supertankers carrying crude oil to the Far East. Consequently, oil spills can occur, causing pollution and contamination in the surrounding areas. Residual oil spills stranded on coastal beaches usually end up as tar-balls. Elucidating the sources of tar-balls using a molecular marker approach is essential in assessing environmental impacts and perhaps settling legal liabilities for affected parties. This study utilizes a multimodal molecular marker approach through the use of diagnostic ratios of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) to determine the source, distribution and weathering of tar-balls. Hopane ratios (e.g., C29/C30, and summation C31-C35/C30 ratios) were used to identify the sources of tar-balls. The weathering effects were distinguished by using alkanes, namely the unresolved complex mixture (UCM) and low molecular weight/high molecular weight (L/H) ratios. Similarly, PAHs were also used for the determination of weathering processes undergone by the tar-balls. This multimodal molecular marker gave a very strong indication of the sources of tar-balls in this study. For example, 16 out of 17 samples originated from South East Asian Crude Oil (SEACO) with one sample from Merang, Terengganu originating from North Sea Oil (Troll). The TRME-2 sample may have come from a supertanker's ballast water discharge. The second possibility is that the tar-ball may have been transported via oceanographic currents. All 'weathered' sample characterizations were based on the presence of UCM and other ratios. The multimodal molecular marker approach applied in this study has enabled us to partially understand the transport behavior of tar-balls in the marine environment and has revealed insights into the weathering process of tar-balls.

  13. Carbon neutral 2020 : a leadership opportunity in Canada's oil sands

    Energy Technology Data Exchange (ETDEWEB)

    McCulloch, M.; Raynolds, M.; Wong, R.; Holmes, R. (ed.)

    2006-10-15

    Canada's greenhouse gas (GHG) emissions are projected to be 32 per cent higher in 2010 than they were in 1990. The development of Canada's oil sands is the single largest contributor to GHG emissions growth in Canada. This report estimates the cost for an oil sands operation to become carbon neutral by 2020. In addition to energy efficiency or fuel switching measures which should be considered on a continual basis, the 2 main options for achieving carbon neutrality are carbon capture and storage (CCS) and GHG offsets. This report considered 3 scenarios: (1) maximum CCS in which all point sources are captured and stored, (2) moderate CCS in which only carbon dioxide from hydrogen production is captured and stored, and (3) maximum offsets in which CCS is not used and all emissions are offset. The results for the 3 scenarios were presented under operating situations that ranged from 100 per cent mining, 100 per cent in-situ, and 55 per cent mining with 45 per cent in-situ operations. The estimated costs per tonne of carbon dioxide equivalent using both CCS and offsets ranged from US $22 to US $66. The costs per barrel for achieving neutrality could therefore range from US $2-14, with the higher costs assigned to the CCS options. It was noted that the cost of becoming carbon neutral will continue to decline as oil sands companies generate greater profits per barrel. It was concluded that carbon neutrality is economically feasibly by 2020, given the current high profit margins for oil sands companies. In addition, the cost of reducing carbon is not much higher per barrel than the cost of removing lead or sulphur from fuel. 67 refs., 13 tabs., 10 figs.

  14. Study of greenhouse gases reduction alternatives for the exploitation of non conventional oil sands in Canada

    Energy Technology Data Exchange (ETDEWEB)

    Bouchonneau, Deborah [Institut Francais du Petrole (IFP), Paris (France)

    2008-07-01

    High energy prices and greenhouse gases reduction represent the main challenges the current worldwide energetic situation has to face. As a consequence, paradox strategies can be highlighted: oil prices are sufficiently high to exploit non conventional oil resources, like extra heavy oils and oil sands. But the production of these resources emits larger GHG than the conventional oil path and implies other major environmental issues (water management, risks of soil pollution, destruction of the boreal forest), incompatible with the rules validated by the protocol of Kyoto. At the light of the new greenhouse gases reduction regulation framework announced by the Canadian Federal government, this work focuses on the study of greenhouse gases reduction alternatives applied to the non conventional oil sands exploitation in Canada. (author)

  15. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2001-08-08

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California, through the testing and application of advanced reservoir characterization and thermal production technologies. The hope is that successful application of these technologies will result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs, including: (1) Development of three-dimensional (3-D) deterministic and stochastic reservoir simulation models--thermal or otherwise--to aid in reservoir management of the steamflood and post-steamflood phases and subsequent development work. (2) Development of computerized 3-D visualizations of the geologic and reservoir simulation models to aid reservoir surveillance and operations. (3) Perform detailed studies of the geochemical interactions between the steam and the formation rock and fluids. (4) Testing and proposed application of a

  16. Assessing the effects of oil sands related ozone precursor emissions on ambient ozone levels in the Alberta oil sands region, Canada

    Science.gov (United States)

    Cho, Sunny; Vijayaraghavan, Krish; Spink, David; Cosic, Biljana; Davies, Mervyn; Jung, Jaegun

    2017-11-01

    A study was undertaken to determine whether, and the extent to which, increased ground-level ozone (O3) precursor emissions from oil sands development have impacted ambient air quality in the north-eastern Alberta, Canada, over the period 1998 to 2012. Temporal trends in emissions of O3 precursors (NOx and VOC) and ambient air concentrations of O3 precursors, and O3 were examined using the Theil-Sen statistical analysis method. Statistically significant correlations between NOx emissions and ambient NOx concentrations were found mainly near surface (open-pit) mining areas where mine fleets are a large source of NOx emissions. No statistically significant trends in the 4th highest daily maximum 8-hr average O3 at any of the continuous and passive ambient air monitoring stations were found. A significant long-term decrease in monthly averaged O3 is observed at some ambient monitoring sites in summer. A visual examination of long-term variations in annual NOx and VOC emissions and annual 4th highest daily maximum 8-hr O3 concentrations does not reveal any indication of a correlation between O3 concentrations and O3 precursor emissions or ambient levels in the study area. Despite a significant increase in oil sands NOx emissions (8%/yr), there is no statistically significant increase in long-term O3 concentrations at any of monitoring stations considered. This suggests that there is surplus NOx available in the environment which results in a titration of ambient O3 in the areas that have ambient monitoring. The limited ambient O3 monitoring data distant from NOx emission sources makes it impossible to assess the impact of these increased O3 precursor levels on O3 levels on a regional scale. As a precautionary measure, the increasing oil sands development O3 precursor emissions would require that priority be given to the management of these emissions to prevent possible future O3 ambient air quality issues.

  17. Fuel alternatives for oil sands development - the nuclear option

    Energy Technology Data Exchange (ETDEWEB)

    Bock, D [Atomic Energy of Canada Ltd., Mississauga, ON (Canada); Donnelly, J K

    1996-12-31

    Currently natural gas is the fuel of choice in all oil sand developments. Alberta sources of hydrocarbon based fuels are large but limited. Canadian nuclear technology was studied as a possible alternative for providing steam for the deep commercial in situ oil sand projects which were initiated over ten years ago. Because the in situ technology of that time required steam at pressures in excess of 10 MPa, the nuclear option required the development of new reactor technology, or the use of steam compressors, which was not economical. The current SAGD (steam assisted gravity drainage) technology requires steam at pressures of less than 5 MPa, which is in the reach of existing Canadian nuclear technology. The cost of supplying steam for a SAGD in situ project using a CANDU 3 nuclear reactor was developed. The study indicates that for gas prices in excess of $2.50 per gigajoule, replacing natural gas fuel with a nuclear reactor is economically feasible for in situ projects in excess of 123 thousand barrels per day. (author). 9 refs., 3 tabs., 12 figs.

  18. Fuel alternatives for oil sands development - the nuclear option

    International Nuclear Information System (INIS)

    Bock, D.; Donnelly, J.K.

    1995-01-01

    Currently natural gas is the fuel of choice in all oil sand developments. Alberta sources of hydrocarbon based fuels are large but limited. Canadian nuclear technology was studied as a possible alternative for providing steam for the deep commercial in situ oil sand projects which were initiated over ten years ago. Because the in situ technology of that time required steam at pressures in excess of 10 MPa, the nuclear option required the development of new reactor technology, or the use of steam compressors, which was not economical. The current SAGD (steam assisted gravity drainage) technology requires steam at pressures of less than 5 MPa, which is in the reach of existing Canadian nuclear technology. The cost of supplying steam for a SAGD in situ project using a CANDU 3 nuclear reactor was developed. The study indicates that for gas prices in excess of $2.50 per gigajoule, replacing natural gas fuel with a nuclear reactor is economically feasible for in situ projects in excess of 123 thousand barrels per day. (author). 9 refs., 3 tabs., 12 figs

  19. A new approach to the management of cumulative environmental impacts, the Alberta Oil Sands area

    International Nuclear Information System (INIS)

    Weagle, K.V.

    2002-01-01

    Resource development in the oil sand industry of Northeastern Alberta is enjoying a wave of renewed interest fuelled in part by changes made in the tax and royalty structure for oil sands developments in the province, the development of new technology and the price of oil. Announcements were made of investments totalling approximately 51 billion dollars in the oil sand industry over the next ten years in all deposits. The issue of cumulative environmental effects has been amplified accordingly. In June 2000, an association was formed, the Cumulative Environmental Management Association (CEMA), consisting of stakeholders and based on consensus, with a mandate to address 72 issues related to potential cumulative impacts in the expanded development of the Wood Buffalo Region. Five working groups were formed, as well as three standing committees. To mitigate the cumulative effects, the working groups and standing committees are working on management objectives, management systems and research recommendations. The regulatory bodies receive the recommendations, and the implementation process involves the issuance of permits and licenses. Research and monitoring activities play a vital role in the environmental management system and are part of other current environmental initiatives. Some of the initiatives are managed by the Wood Buffalo Environmental Association, Regional Aquatics Monitoring Program, and the Canadian Oil Sands Network for Research and Development. These organizations touch on topics including air quality monitoring, aquatics monitoring and environmental research. 1 fig

  20. Energy consumption and greenhouse gas emissions in the recovery and extraction of crude bitumen from Canada’s oil sands

    International Nuclear Information System (INIS)

    Nimana, Balwinder; Canter, Christina; Kumar, Amit

    2015-01-01

    Highlights: • A model to estimate energy consumption and GHG emissions in oil sands is presented. • The model is developed from fundamental engineering principles. • Cogeneration in the oil sands has the ability to offset GHG emissions. • The effect of key parameters is investigated through a sensitivity analysis. - Abstract: A model – FUNNEL-GHG-OS (FUNdamental ENgineering PrinciplEs-based ModeL for Estimation of GreenHouse Gases in the Oil Sands) was developed to estimate project-specific energy consumption and greenhouse gas emissions (GHGs) in major recovery and extraction processes in the oil sands, namely surface mining and in situ production. This model estimates consumption of diesel (4.4–7.1 MJ/GJ of bitumen), natural gas (52.7–86.4 MJ/GJ of bitumen) and electricity (1.8–2.1 kW h/GJ of bitumen) as fuels in surface mining. The model also estimates the consumption of natural gas (123–462.7 MJ/GJ of bitumen) and electricity (1.2–3.5 kW h/GJ of bitumen) in steam assisted gravity drainage (SAGD), based on fundamental engineering principles. Cogeneration in the oil sands, with excess electricity exported to Alberta’s grid, was also explored. Natural gas consumption forms a major portion of the total energy consumption in surface mining and SAGD and thus is a main contributor to GHG emissions. Emissions in surface mining and SAGD range from 4.4 to 7.4 gCO 2 eq/MJ of bitumen and 8.0 to 34.0 gCO 2 eq/MJ of bitumen, respectively, representing a wide range of variability in oil sands projects. Depending upon the cogeneration technology and the efficiency of the process, emissions in oil sands recovery and extraction can be reduced by 16–25% in surface mining and 33–48% in SAGD. Further, a sensitivity analysis was performed to determine the effects of key parameters on the GHG emissions in surface mining and SAGD. Temperature and the consumption of warm water in surface mining and the steam-to-oil ratio (SOR) in SAGD are major parameters

  1. Properties of palm oil fuel ash cement sand brick containing pulverized cockle shell as partial sand replacement

    Science.gov (United States)

    Mat Aris, S.; Muthusamy, K.; Uzer, A.; Ahmad, S. Wan

    2018-04-01

    Environmental pollution caused by the disposal of solid wastes generated from both palm oil industry and cockle shell trade has motivated researches to explore the potential of these wastes. Integrating these wastes in production of construction material is one of the ways to reduce amount of waste thrown at dumping area. Thus, the present investigation investigates the performance of palm oil fuel ash (POFA) cement sand brick containing pulverized cockle shell as partial fine aggregate replacement. All mixes used contain 20% of POFA as partial cement replacement. Total of six mixes were prepared by adding a range of pulverized cockle shell that is 0%, 10%, 20%, 30%, 40% and 50% as partial sand replacement. The mixes were prepared in form of brick. All the water cured samples were tested for compressive strength and flexural strength until 28 days. Findings show that brick produced using 20% pulverized cockle shell exhibit the highest compressive strength and flexural strength also the lowest water absorption value.

  2. Marketing opportunities and challenges for Canada's oil sands industry

    International Nuclear Information System (INIS)

    1995-01-01

    This report demonstrated that effective marketing of Canadian oil sands products has been vital to the success of the industry in the past. Future success was expected to depend on having efficient transportation systems for the industry's products, unrestricted access to markets, and a range of products can competitively meet the needs of specific markets and customs. 9 ills

  3. Isolation of CYP1A inducing components in coal tar fraction (F3) of Alaska north slope crude oil : a preliminary study

    Energy Technology Data Exchange (ETDEWEB)

    Saravanabhavan, G.; Brown, R.S. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry; Khan, C.W.; Hodson, P.V. [Queen' s Univ., Kingston, ON (Canada). Dept. of Biology

    2004-07-01

    Recent concerns regarding the effects of weathered crude oil on the early life stage of aquatic organisms are related to reports that blue sac disease (BSD) has been linked to larval fish exposed to crude oil. Studies have shown that a relationship exists between the induction of CYP1A enzymes and the occurrence of BSD in fish species. However, the mechanism of BSD is not fully understood. This study contributed to the Toxicity Identification and Evaluation (TIE) approach by isolating the CYP1A enzyme. An improved separation and analysis method for characterizing crude oil was also developed. Earlier studies revealed that the highest CYP1A activity occurred in the coal tar fraction of crude oil, which is rich in polycyclic aromatic hydrocarbons (PAH) and which contains many classes of compounds such as waxes, asphaltenes and resins. The TIE method included separation of these compound classes as well as a detailed characterization of the PAH classes. A solvent extraction method was also developed to fractionate the coal tar fraction into compound classes with particular emphasis on isolating PAH components. The study showed that fractions rich in PAH were responsible for a significant CYP1A induction in juvenile trout, but fractions poor in PAH did not. The solid phase extraction method offered better PAH fractions for further analysis by liquid chromatography.

  4. Thermochemical method for the treatment of oil contaminated sand; Metodo termoquimico para tratamento de areia contaminada por oleo

    Energy Technology Data Exchange (ETDEWEB)

    Pimenta, Rosana C.G.M. [Fundacao Gorceix, Ouro Preto, MG (Brazil)]|[PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Khalil, Carlos N. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2004-07-01

    In January 2000 there was a major oil spill in Guanabara Bay, Rio de Janeiro, which contaminated 2400 tons of sand. This work, based on NGS (Nitrogen Generating System) technology, was adapted for cleaning contaminated sand and recovering of spilled oil. NGS is a thermochemical method first developed for removal of paraffin deposits in production and export pipelines. The method is based on a strongly exothermic redox chemical reaction between two salts catalyzed in acidic pH. The reaction products are harmless to the environment and consist of nitrogen, sodium chloride, water and heat. By combining simultaneous effects of the treatment such as heating, turbulence and floatation, one can remove, within 98% of efficiency, spilling oil from contaminated sand. After treatment, removed oil can be securely returned to refining process. The method has proved to be efficient, fast, low cost and ecologically correct method for cleaning contaminated sand and can be applied in place right after a contamination event. (author)

  5. The effect of oil sands tailings pond sediments on embryo-larval walleye (Sander vitreus).

    Science.gov (United States)

    Raine, J C; Turcotte, D; Tumber, V; Peru, K M; Wang, Z; Yang, C; Headley, J V; Parrott, J L

    2017-10-01

    Walleye (Sander vitreus) are a commercially important North American fish species that inhabit the Athabasca River. This river flows through the Athabasca oil sands where natural sources of bitumen erode from the McMurray formation. Little information is available on responses of walleye embryos to oil sands tailings pond sediments in a laboratory setting. The current study describes the design and implementation of a daily-renewal bioassay to assess the potential effects of tailings pond sediments from the Athabasca oil sands area on walleye development. Developing walleye embryos were exposed to increasing concentrations of two tailings pond sediments (collected in the Athabasca oil sands area) until the completion of yolk absorption in control fish. Sediments from the tailings pond represent a mixture of polycyclic aromatic hydrocarbons (PAHs) and alkylated PAHs. During the 31 day exposure, the walleye were examined for mortalities, weight, length and developmental abnormalities to provide an initial evaluation of the effects of the oil sands tailings pond sediments. Walleye embryo survival differed between the tailings pond sediments, and survival decreased with increasing sediment concentration. Alkylated PAH content differed between the two tailings pond sediments and lower embryo survival corresponded to higher total and alkylated PAH content. Tailings pond sediment-exposed walleye exhibited a delay in development, as well as increased percentages of larvae with heart and yolk sac edema, and cranial and spinal malformations. These abnormalities in development are often associated with PAH and alkylated PAH exposure. This study provides an exposure design that can be used to assess sediment toxicity to early developmental stages of a fish species not commonly tested in the lab, and lays the groundwork for future studies with this and other difficult-to-culture species. These results offer information on the potential effects of tailings pond sediments

  6. An assessment of ground-level ozone concentrations in the Athabasca oil sands region

    International Nuclear Information System (INIS)

    1997-01-01

    Syncrude and Suncor have plans to develop new oil sands leases and to increase crude oil and bitumen recovery in the Athabasca oil sands region. A first air quality assessment was prepared as part of the Alberta Energy and Utilities Board application, in order to evaluate the emissions and potential impacts associated with the development. The Pembina Institute raised several issues with respect to potential future changes in ambient ozone levels as a result of the Aurora Mine operations. In response to these concerns, another more rigorous assessment was conducted to predict future ground-level ozone concentrations in the Fort McMurray area. This report includes: (1) ambient air quality guidelines for ozone, (2) emissions inventory for dispersion modelling, (3) dispersion modelling methodology, and (4) predicted ambient ozone concentrations. Ground level ozone (O 3 ) concentrations result from anthropogenically produced ozone, and from naturally occurring ozone. Ozone is not directly emitted to the atmosphere from industrial sources, but is formed as a result of chemical reactions between NO x and VOCs, which are emitted from industrial sources within the Athabasca oil sands region. NO x and VOC emissions associated with the Aurora Mine operation are predicted to increase hourly average ozone concentrations in the Fort McMurray area by only 0.001 ppm. 17 refs., 18 tabs., 5 figs

  7. Oil shales and tar sands: a bibliography. Supplement 2, Parts 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    Grissom, M.C. (ed.)

    1984-07-01

    This bibliography includes 4715 citations arranged in the broad subject categories: reserves and exploration; site geology and hydrology; drilling, fracturing, and mining; oil production, recovery, and refining; properties and composition; direct uses and by-products; health and safety; marketing and economics; waste research and management; environmental aspects; regulations; and general. There are corporate, author, subject, contract number, and report number indexes.

  8. Mass spectrometry of oil sands naphthenic acids : degradation in OSPW and wetland plants

    Energy Technology Data Exchange (ETDEWEB)

    Headley, J. [Environment Canada, Saskatoon, SK (Canada). Water Science and Technology Directorate

    2009-07-01

    This presentation discussed mass spectrometry of oil sands naphthenic acids and the degradation in OSPW and wetland plants. It presented background information on the Athabasca oil sands and naphthenic acids which involve a mixture of alkanes and cycloalkane carboxylic acids with aliphatic side chains. The presentation also discussed mass spectrometry with electrospray operating in negative ion modes. Loop injection, external standard methods and solid phase extraction were reviewed along with improved analysis by removing background ions. Other topics that were presented included hydroponic test systems and wetland plant toxicity, growth and transpiration. It was concluded that dissipation included species containing oxygen, ozone, O{sub 4}, and O{sub 5}. tabs., figs.

  9. Saskatchewan's place in Canadian oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Schramm, L.L. [Saskatchewan Research Council, Regina, SK (Canada); Kramers, J.W. [Owl Ventures Inc., Edmonton, AB (Canada); Isaacs, E.E. [Alberta Energy Research Inst., Edmonton, AB (Canada)

    2010-11-15

    The current daily bitumen and synthetic crude production from the Western Canada Sedimentary Basin is 180,000 m{sup 3}, which represents approximately 40 percent of crude oil produced in Canada. In a time of peaking conventional oil production, the search for new oil reserves has led to unconventional in-situ bitumen and heavy oil resources, including shallow in-situ resources. The great difficulty in producing bitumen and managing water flows in such reservoirs will require innovative approaches and increasingly environmentally sustainable practices. This paper presented an overview of shallow in-situ oil sands and the novel recovery technologies that are being developed that will reduce the use of steam and fresh water, and also reduce greenhouse gas emissions. Research and development programs are currently underway to develop and demonstrate such new technologies. Promising technologies include the solvent vapour extraction and hybrid thermal solvent extraction processes that are being developed and demonstrated in large-scale three-dimensional scaled physical models and associated numerical simulation models. Electrical heating and gravity stable combustion are other examples of technologies that could play a significant role in developing these resources. 81 refs., 3 tabs., 8 figs.

  10. A case study on effects of oil spills and tar-ball pollution on beaches of Goa (India).

    Science.gov (United States)

    Rekadwad, Bhagwan N; Khobragade, Chandrahasya N

    2015-11-15

    This paper reports the impact of oil spills and tar-ball pollution on the coastal ecosystem of Goa. The factors responsible for degrading the marine ecosystem of the Goan coastline are analyzed. Uncontrolled activities were found to degrade the marine and coastal biodiversity, in turn polluting all beaches. This had a direct impact on the Goan economy through a decline in tourism. The government must adopt the necessary control measures to restore Goan beaches and the surrounding coastal areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Characterization of Volatile Organic Compound (VOC) Emissions at Sites of Oil Sands Extraction and Upgrading in northern Alberta

    Science.gov (United States)

    Marrero, J.; Simpson, I. J.; Meinardi, S.; Blake, D. R.

    2011-12-01

    The crude oil reserves in Canada's oil sands are second only to Saudi Arabia, holding roughly 173 billion barrels of oil in the form of bitumen, an unconventional crude oil which does not flow and cannot be pumped without heating or dilution. Oil sands deposits are ultimately used to make the same petroleum products as conventional forms of crude oil, though more processing is required. Hydrocarbons are the basis of oil, coal and natural gas and are an important class of gases emitted into the atmosphere during oil production, particularly because of their effects on air quality and human health. However, they have only recently begun to be independently assessed in the oil sands regions. As part of the 2008 ARCTAS airborne mission, whole air samples were collected in the boundary layer above the surface mining operations of northern Alberta. Gas chromatography analysis revealed enhanced concentrations of 53 VOCs (C2 to C10) over the mining region. When compared to local background levels, the measured concentrations were enhanced up to 1.1-400 times for these compounds. To more fully characterize emissions, ground-based studies were conducted in summer 2010 and winter 2011 in the oil sands mining and upgrading areas. The data from the 200 ground-based samples revealed enhancements in the concentration of 65 VOCs. These compounds were elevated up to 1.1-3000 times above background concentrations and include C2-C8 alkanes, C1-C5 alkyl nitrates, C2-C4 alkenes and potentially toxic aromatic compounds such as benzene, toluene, and xylenes.

  12. Hydrotreating of heavy gas oil derived from Athabasca bitumen using NiMo/Al2O3 catalyst containing boron and phosphorus : effects of process conditions on the product selectivity

    Energy Technology Data Exchange (ETDEWEB)

    Ferdous, D.; Dalai, A.K. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Chemistry and Chemical Engineering; Adjaye, J. [Syncrude Canada Ltd., Edmonton, AB (Canada). Edmonton Research Centre

    2004-07-01

    In response to concerns regarding the depletion of conventional oil reserves, there has been much interest in modifying the hydrotreating process for upgrading tar sands and shale oils for producing transportation fuels. Oil sand bitumens and their derived products have a high level of nitrogen which deactivates the catalysts used in fluid catalytic cracking and hydrocracking. A better catalyst is needed to efficiently remove nitrogen from oil sand-derived gas oils. In this study, a trickle-bed reactor containing NiMo/Al{sub 2}O{sub 3} catalysts with boron and phosphorous was used to remove the sulfur and nitrogen from heavy gas oils derived from Athabasca bitumen. The operating conditions of the reactor in terms of temperature and pressure were described. Sulfur and nitrogen conversion was found to increase substantially with the boron catalysts. Gasoline selectivity also increased with an increase in temperature. However, a change in operating conditions did not significantly affect the net content of the gas oil fraction. This study also compared the results of using either the boron or phosphorous catalyst.

  13. Applying the Analytic Hierarchy Process to Oil Sands Environmental Compliance Risk Management

    Science.gov (United States)

    Roux, Izak Johannes, III

    Oil companies in Alberta, Canada, invested $32 billion on new oil sands projects in 2013. Despite the size of this investment, there is a demonstrable deficiency in the uniformity and understanding of environmental legislation requirements that manifest into increased project compliance risks. This descriptive study developed 2 prioritized lists of environmental regulatory compliance risks and mitigation strategies and used multi-criteria decision theory for its theoretical framework. Information from compiled lists of environmental compliance risks and mitigation strategies was used to generate a specialized pairwise survey, which was piloted by 5 subject matter experts (SMEs). The survey was validated by a sample of 16 SMEs, after which the Analytic Hierarchy Process (AHP) was used to rank a total of 33 compliance risks and 12 mitigation strategy criteria. A key finding was that the AHP is a suitable tool for ranking of compliance risks and mitigation strategies. Several working hypotheses were also tested regarding how SMEs prioritized 1 compliance risk or mitigation strategy compared to another. The AHP showed that regulatory compliance, company reputation, environmental compliance, and economics ranked the highest and that a multi criteria mitigation strategy for environmental compliance ranked the highest. The study results will inform Alberta oil sands industry leaders about the ranking and utility of specific compliance risks and mitigations strategies, enabling them to focus on actions that will generate legislative and public trust. Oil sands leaders implementing a risk management program using the risks and mitigation strategies identified in this study will contribute to environmental conservation, economic growth, and positive social change.

  14. Considerations when ranking stochastically modeled oil sands resource models for mining applications

    Energy Technology Data Exchange (ETDEWEB)

    Etris, E.L. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Petro-Canada, Calgary, AB (Canada); Idris, Y.; Hunter, A.C. [Petro-Canada, Calgary, AB (Canada)

    2008-10-15

    Alberta's Athabasca oil sands deposit has been targeted as a major resource for development. Bitumen recovery operations fall into 2 categories, namely mining and in situ operations. Mining recovery is done above ground level and consists of open pit digging, disaggregation of the bitumen-saturated sediment through crushing followed by pipeline transport in a water-based slurry and then separation of oil, water and sediment. In situ recovery consists of drilling wells and stimulating the oil sands in the subsurface with a thermal treatment to reduce the viscosity of the bitumen and allow it to come to the surface. Steam assisted gravity drainage (SAGD) is the most popular thermal treatment currently in use. Resource models that simulate the recovery process are needed for both mining and in situ recovery operations. Both types can benefit from the advantages of a stochastic modeling process for resource model building and uncertainty evaluation. Stochastic modeling provides a realistic geology and allows for multiple realizations, which mining operations can use to evaluate the variability of recoverable bitumen volumes and develop mine plans accordingly. This paper described the processes of stochastic modelling and of determining the appropriate single realization for mine planning as applied to the Fort Hills oil sands mine which is currently in the early planning stage. The modeling exercise was used to estimate the in-place resource and quantify the uncertainty in resource volumes. The stochastic models were checked against those generated from conventional methods to identify any differences and to make the appropriate adaptations. 13 refs., 3 tabs., 16 figs.

  15. Institutionalizing environmental due diligence as part of the organization's culture: The Suncor Oil Sands Group experience

    International Nuclear Information System (INIS)

    Allen, R.; Klym, D.

    1992-01-01

    The Suncor Oil Sands Group produces ca 22 million bbl/y of synthetic crude oil from oil sands in northern Alberta. Initiatives taken by the Group to install environmental due diligence as an integral part of Suncor culture are reviewed. Environmental due diligence means taking all reasonable care to safeguard the environment. To practice environmental due diligence, the organization and its members must have an environmental consciousness that can be observed, measured, and monitored through daily practices. In the period from startup of the oil sands plant in 1967 to the mid-1970s, Suncor culture could be described as research oriented, oriented toward examination of the viability of extracting oil from the oil sands and the development of new extraction processes. Management then moved toward a more production-based culture, in which environmental issues were sometimes perceived to be in conflict with production goals. External factors toward the end of the 1980s created a culture shift to an integration of production culture with social entities including environmental consciousness. A corporate push toward a new environmental culture was first concretized when the management's Health and Safety Policy was changed in 1990 to the Health, Safety and Environment Policy. A new Environmental Diligence Program was implemented in three phases, including planning, development of a comprehensive environmental management system, and implementation. Installation of the Program in the first phase is described, focusing on employee and management training, and results of the installation process are presented. Modifications of Suncor's loss control management program to integrate with the environmental diligence program are also noted. 2 refs

  16. Gill histopathology of goldfish exposed to oil sands processed-waters

    International Nuclear Information System (INIS)

    Nero, V.; Farwell, A.J.; Dixon, D.G.; Lee, L.E.J.

    2002-01-01

    Large volumes of processed wastewater are generated through the oil extraction process at Alberta's Athabasca oil sand deposit. These wastewaters are very toxic to aquatic biota because they are high in salinity and consist of napthenic acids and polycyclic aromatic hydrocarbons (PAH). In this study, goldfish were caged in 3 different experimental ponds in order to evaluate the biological effects of aquatic reclamation alternatives for process-affected waters. The first pond was a control pond, while the other 2 ponds consisted of known and varying chemicals. The fish were exposed to the ponds for 19 days. Those in the pond with elevated levels of napthenic acids and high salinity exhibited severe gill histopathological changes. Alterations included epithelial hyperplasia resulting in severe lamellar fusion, chloride cell hyperplasia, and lamellar edema, all of which were believed to be defense responses of the fish. Additional severe gill alterations were also observed that may indicate the direct negative effects of oil sands processed-water on fish. Exposed goldfish also showed signs of necrosis and degenerative changes resulting in desquamation of the epithelial surfaces of the gill, which are symptoms seen in free-range exposure of yellow perch, a native fish species, at the same sites and exposure times

  17. Gill histopathology of goldfish exposed to oil sands processed-waters

    Energy Technology Data Exchange (ETDEWEB)

    Nero, V.; Farwell, A.J.; Dixon, D.G. [Waterloo Univ., ON (Canada). Dept. of Biology; Lister, A.; Van Der Kraak, G.J. [Guelph Univ., ON (Canada); Lee, L.E.J. [Wilfred Laurier Univ., Waterloo, ON (Canada). Dept. of Biology

    2002-07-01

    Large volumes of processed wastewater are generated through the oil extraction process at Alberta's Athabasca oil sand deposit. These wastewaters are very toxic to aquatic biota because they are high in salinity and consist of napthenic acids and polycyclic aromatic hydrocarbons (PAH). In this study, goldfish were caged in 3 different experimental ponds in order to evaluate the biological effects of aquatic reclamation alternatives for process-affected waters. The first pond was a control pond, while the other 2 ponds consisted of known and varying chemicals. The fish were exposed to the ponds for 19 days. Those in the pond with elevated levels of napthenic acids and high salinity exhibited severe gill histopathological changes. Alterations included epithelial hyperplasia resulting in severe lamellar fusion, chloride cell hyperplasia, and lamellar edema, all of which were believed to be defense responses of the fish. Additional severe gill alterations were also observed that may indicate the direct negative effects of oil sands processed-water on fish. Exposed goldfish also showed signs of necrosis and degenerative changes resulting in desquamation of the epithelial surfaces of the gill, which are symptoms seen in free-range exposure of yellow perch, a native fish species, at the same sites and exposure times.

  18. Methanogenic biodegradation of paraffinic solvent hydrocarbons in two different oil sands tailings.

    Science.gov (United States)

    Mohamad Shahimin, Mohd Faidz; Siddique, Tariq

    2017-04-01

    Microbial communities drive many biogeochemical processes in oil sands tailings and cause greenhouse gas emissions from tailings ponds. Paraffinic solvent (primarily C 5 -C 6 ; n- and iso-alkanes) is used by some oil sands companies to aid bitumen extraction from oil sands ores. Residues of unrecovered solvent escape to tailings ponds during tailings deposition and sustain microbial metabolism. To investigate biodegradation of hydrocarbons in paraffinic solvent, mature fine tailings (MFT) collected from Albian and CNRL ponds were amended with paraffinic solvent at ~0.1wt% (final concentration: ~1000mgL -1 ) and incubated under methanogenic conditions for ~1600d. Albian and CNRL MFTs exhibited ~400 and ~800d lag phases, respectively after which n-alkanes (n-pentane and n-hexane) in the solvent were preferentially metabolized to methane over iso-alkanes in both MFTs. Among iso-alkanes, only 2-methylpentane was completely biodegraded whereas 2-methylbutane and 3-methylpentane were partially biodegraded probably through cometabolism. 16S rRNA gene pyrosequencing showed dominance of Anaerolineaceae and Methanosaetaceae in Albian MFT and Peptococcaceae and co-domination of "Candidatus Methanoregula" and Methanosaetaceae in CNRL MFT bacterial and archaeal communities, respectively, during active biodegradation of paraffinic solvent. The results are important for developing future strategies for tailings reclamation and management of greenhouse gas emissions. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Co-occurrence of methanogenesis and N2 fixation in oil sands tailings.

    Science.gov (United States)

    Collins, C E Victoria; Foght, Julia M; Siddique, Tariq

    2016-09-15

    Oil sands tailings ponds in northern Alberta, Canada have been producing biogenic gases via microbial metabolism of hydrocarbons for decades. Persistent methanogenic activity in tailings ponds without any known replenishment of nutrients such as fixed nitrogen (N) persuaded us to investigate whether N2 fixation or polyacrylamide (PAM; used as a tailings flocculant) could serve as N sources. Cultures comprising mature fine tailings (MFT) plus methanogenic medium supplemented with or deficient in fixed N were incubated under an N2 headspace. Some cultures were further amended with citrate, which is used in oil sands processing, as a relevant carbon source, and/or with PAM. After an initial delay, N-deficient cultures with or without PAM produced methane (CH4) at the same rate as N-containing cultures, indicating a mechanism of overcoming apparent N-deficiency. Acetylene reduction and (15)N2 incorporation in all N-deficient cultures (with or without PAM) suggested active N2 fixation concurrently with methanogenesis but inability to use PAM as a N source. 16S rRNA gene pyrosequencing revealed little difference between archaeal populations regardless of N content. However, bacterial sequences in N-deficient cultures showed enrichment of Hyphomicrobiaceae and Clostridium members that might contain N2-fixing species. The results are important in understanding long-term production of biogenic greenhouse gases in oil sands tailings. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Advanced testing and characterization of shear modulus and deformation characteristics of oil sand materials

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2014-09-01

    Full Text Available and Pressures,” Can. Geotech. J., Vol. 24, 1987, pp. 1–10. [5] Samieh, A.M. and Wong, R.C.K., “Deformation of Athabasca Oil Sand in Triaxial Compression Tests at Low Effective Stresses under Varying Boundary Conditions,” Can. Geotech. J., Vol.34, 1997, pp.... 985– 990. [6] Samieh, A.M. and Wong, R.C.K., “Modeling the Responses of Athabasca Oil Sand in Triaxial Compression Tests at Low Pressure,” Can. Geotech. J., Vol. 35, 1998, pp. 395–406. [7] AASHTO Standard T265, 2009, “Laboratory Determination...

  1. Improvement of Dune Sands by Residual Oil in Order to Use in Construction of Lagoons

    Directory of Open Access Journals (Sweden)

    Alborz Hajian nia

    2011-10-01

    Full Text Available This research which is based on experimental work, devoted to study the improvement and stabilization of dune sands in order to create strong layer and stabilize slope and floor construction of sewage Lagoons. Materials used stabilizing these soils are residual oil from the refinery. To confirm the effectiveness of the use of residual oil to improve the mechanical properties of the sand, various samples with different percentages were tested. In besides, the geotechnical and environmental tests were done. Results demonstrate that samples made with 5% oil have highest shear and unconfined compaction strength. It revealed that in compare with natural samples, cohesion and loading capacity highly increased and permeability decrease well. Percentage of fine aggregate, minerals and durability of oil in soil material were also investigated. Finally, effects of sewage on the samples were analyzed, and performance the oils were evaluated in order to use in lagoons.

  2. Microbially-accelerated consolidation of oil sands tailings. Pathway I: changes in porewater chemistry.

    Science.gov (United States)

    Siddique, Tariq; Kuznetsov, Petr; Kuznetsova, Alsu; Arkell, Nicholas; Young, Rozlyn; Li, Carmen; Guigard, Selma; Underwood, Eleisha; Foght, Julia M

    2014-01-01

    Dispersed clay particles in mine tailings and soft sediments remain suspended for decades, hindering consolidation and challenging effective management of these aqueous slurries. Current geotechnical engineering models of self-weight consolidation of tailings do not consider microbial contribution to sediment behavior, however, here we show that microorganisms indigenous to oil sands tailings change the porewater chemistry and accelerate consolidation of oil sands tailings. A companion paper describes the role of microbes in alteration of clay chemistry in tailings. Microbial metabolism in mature fine tailings (MFT) amended with an organic substrate (hydrolyzed canola meal) produced methane (CH4) and carbon dioxide (CO2). Dissolution of biogenic CO2 lowered the pH of amended MFT to pH 6.4 vs. unamended MFT (pH 7.7). About 12% more porewater was recovered from amended than unamended MFT during 2 months of active microbial metabolism, concomitant with consolidation of tailings. The lower pH in amended MFT dissolved carbonate minerals, thereby releasing divalent cations including calcium (Ca(2+)) and magnesium (Mg(2+)) and increasing bicarbonate (HCO(-) 3) in porewater. The higher concentrations increased the ionic strength of the porewater, in turn reducing the thickness of the diffuse double layer (DDL) of clay particles by reducing the surface charge potential (repulsive forces) of the clay particles. The combination of these processes accelerated consolidation of oil sands tailings. In addition, ebullition of biogenic gases created transient physical channels for release of porewater. In contrast, saturating the MFT with non-biogenic CO2 had little effect on consolidation. These results have significant implications for management and reclamation of oil sands tailings ponds and broad importance in anaerobic environments such as contaminated harbors and estuaries containing soft sediments rich in clays and organics.

  3. A science and technology strategy for Canada's oil sands industry

    International Nuclear Information System (INIS)

    1995-01-01

    This report showed that science and technology are the basis for all current oil sands operations. Study proved that technological breakthroughs were essential for future grassroots investment. Assuming that the price of oil would remain in the range of 15 to 20 dollars a barrel, new technologies would be the key lever to economically sound commercial development. Technologies should reduce capital, operating as well as transportation costs. It was urged that, in the development of new technologies, emphasis should be put on technologies that eliminate or bypass entire sections of the current cost structure

  4. Thermochemical methods for the treatment of oil contaminated sand; Metodo termoquimico para tratamento de areia contaminada por oleo

    Energy Technology Data Exchange (ETDEWEB)

    Pimenta, Rosana C.G.M. [Fundacao Jose Bonifacio, Rio de Janeiro, RJ (Brazil); Khalil, Carlos N. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2003-07-01

    The Nitrogen Generating System (SGN in Portuguese) is a thermochemical method first developed for cleaning and removal of paraffin deposits in production and export pipelines. SGN is based on a redox chemical reaction between two salts which is catalyzed in acidic pH. The reaction is strongly exothermic and its products are nitrogen, sodium chloride, water and heat. All reaction products are harmless to the environment. In January 2000 there was a major oil spill in Guanabara Bay, Rio de Janeiro, which contaminated 2400 tons of sand. This work, developed at PETROBRAS Research Center (CENPES), was based on SGN technology which has been adapted for cleaning contaminated sand and recovering of spilled oil. By combining simultaneous effects of the SGN treatment such as heating, turbulence and floatation, one can remove, within 98% of efficiency, spilling oil from contaminated sand and removed oil can be securely returned to refining process. SGN technology has proved to be efficient, fast, low cost and ecologically correct method for cleaning contaminated sand and can be applied in loco right after a contamination event. (author)

  5. Impacts of oil sands process water on fen plants: Implications for plant selection in required reclamation projects

    International Nuclear Information System (INIS)

    Pouliot, Rémy; Rochefort, Line; Graf, Martha D.

    2012-01-01

    Fen plant growth in peat contaminated with groundwater discharges of oil sands process water (OSPW) was assessed in a greenhouse over two growing seasons. Three treatments (non-diluted OSPW, diluted OSPW and rainwater) were tested on five vascular plants and four mosses. All vascular plants tested can grow in salinity and naphthenic acids levels currently produced by oil sands activity in northwestern Canada. No stress sign was observed after both seasons. Because of plant characteristics, Carex species (C. atherodes and C. utriculata) and Triglochin maritima would be more useful for rapidly restoring vegetation and creating a new peat-accumulating system. Groundwater discharge of OSPW proved detrimental to mosses under dry conditions and ensuring adequate water levels would be crucial in fen creation following oil sands exploitation. Campylium stellatum would be the best choice to grow in contaminated areas and Bryum pseudotriquetrum might be interesting as it has spontaneously regenerated in all treatments. - Highlights: ► Fen plant growth was assessed under groundwater discharges of oil sands process water. ► Sedge and grass species were not stressed after two growing seasons in greenhouse. ► Carex species and Triglochin maritima would be helpful in created contaminated fens. ► In dry conditions, contaminated groundwater discharge was detrimental for mosses. ► Campylium stellatum would be the best choice in created fens with contaminated water. - Sedges and grasses tolerated the contact with oil sands process water and could probably grow well in contaminated created fens, but mosses were particularly affected under dry conditions.

  6. Nearshore dynamics of artificial sand and oil agglomerates

    Science.gov (United States)

    Dalyander, P. Soupy; Plant, Nathaniel G.; Long, Joseph W.; McLaughlin, Molly R.

    2015-01-01

    Weathered oil can mix with sediment to form heavier-than-water sand and oil agglomerates (SOAs) that can cause beach re-oiling for years after a spill. Few studies have focused on the physical dynamics of SOAs. In this study, artificial SOAs (aSOAs) were created and deployed in the nearshore, and shear stress-based mobility formulations were assessed to predict SOA response. Prediction sensitivity to uncertainty in hydrodynamic conditions and shear stress parameterizations were explored. Critical stress estimates accounting for large particle exposure in a mixed bed gave the best predictions of mobility under shoaling and breaking waves. In the surf zone, the 10-cm aSOA was immobile and began to bury in the seafloor while smaller size classes dispersed alongshore. aSOAs up to 5 cm in diameter were frequently mobilized in the swash zone. The uncertainty in predicting aSOA dynamics reflects a broader uncertainty in applying mobility and transport formulations to cm-sized particles.

  7. Bituminous sands : tax issues

    International Nuclear Information System (INIS)

    Patel, B.

    2004-01-01

    This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

  8. Increasing heavy oil reserves in the Wilmington Oil Field through advanced reservoir characterization and thermal production technologies. Annual report, March 30, 1995--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    The objective of this project is to increase heavy oil reserves in a portion of the Wilmington Oil Field, near Long Beach, California, by implementing advanced reservoir characterization and thermal production technologies. Based on the knowledge and experience gained with this project, these technologies are intended to be extended to other sections of the Wilmington Oil Field, and, through technology transfer, will be available to increase heavy oil reserves in other slope and basin clastic (SBC) reservoirs. The project involves implementing thermal recovery in the southern half of the Fault Block II-A Tar zone. The existing steamflood in Fault Block II-A has been relatively inefficient due to several producibility problems which are common in SBC reservoirs. Inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil, and nonuniform distribution of remaining oil have all contributed to poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated formation sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery efficiency and reduce operating costs.

  9. Water issues associated with heavy oil production.

    Energy Technology Data Exchange (ETDEWEB)

    Veil, J. A.; Quinn, J. J.; Environmental Science Division

    2008-11-28

    Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

  10. A risk-based approach for identifying constituents of concern in oil sands process-affected water from the Athabasca Oil Sands region.

    Science.gov (United States)

    McQueen, Andrew D; Kinley, Ciera M; Hendrikse, Maas; Gaspari, Daniel P; Calomeni, Alyssa J; Iwinski, Kyla J; Castle, James W; Haakensen, Monique C; Peru, Kerry M; Headley, John V; Rodgers, John H

    2017-04-01

    Mining leases in the Athabasca Oil Sands (AOS) region produce large volumes of oil sands process-affected water (OSPW) containing constituents that limit beneficial uses and discharge into receiving systems. The aim of this research is to identify constituents of concern (COCs) in OSPW sourced from an active settling basin with the goal of providing a sound rational for developing mitigation strategies for using constructed treatment wetlands for COCs contained in OSPW. COCs were identified through several lines of evidence: 1) chemical and physical characterization of OSPW and comparisons with numeric water quality guidelines and toxicity endpoints, 2) measuring toxicity of OSPW using a taxonomic range of sentinel organisms (i.e. fish, aquatic invertebrates, and a macrophyte), 3) conducting process-based manipulations (PBMs) of OSPW to alter toxicity and inform treatment processes, and 4) discerning potential treatment pathways to mitigate ecological risks of OSPW based on identification of COCs, toxicological analyses, and PBM results. COCs identified in OSPW included organics (naphthenic acids [NAs], oil and grease [O/G]), metals/metalloids, and suspended solids. In terms of species sensitivities to undiluted OSPW, fish ≥ aquatic invertebrates > macrophytes. Bench-scale manipulations of the organic fractions of OSPW via PBMs (i.e. H 2 O 2 +UV 254 and granular activated charcoal treatments) eliminated toxicity to Ceriodaphnia dubia (7-8 d), in terms of mortality and reproduction. Results from this study provide critical information to inform mitigation strategies using passive or semi-passive treatment processes (e.g., constructed treatment wetlands) to mitigate ecological risks of OSPW to aquatic organisms. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Robotics and automation for oil sands bitumen production and maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Lipsett, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Mechanical Engineering

    2008-07-01

    This presentation examined technical challenges and commercial challenges related to robotics and automation processes in the mining and oil sands industries. The oil sands industry has on-going cost pressures. Challenges include the depths to which miners must travel, as well as problems related to equipment reliability and safety. Surface mines must operate in all weather conditions with a variety of complex systems. Barriers for new technologies include high capital and operating expenses. It has also proven difficult to integrate new technologies within established mining practices. However, automation has the potential to improve mineral processing, production, and maintenance processes. Step changes can be placed in locations that are hazardous or inaccessible. Automated sizing, material, and ventilation systems are can also be implemented as well as tele-operated equipment. Prototypes currently being developed include advanced systems for cutting; rock bolting; loose rock detection systems; lump size estimation; unstructured environment sensing; environment modelling; and automatic task execution. Enabling technologies are now being developed for excavation, haulage, material handling systems, mining and reclamation methods, and integrated control and reliability. tabs., figs.

  12. Alberta oil sands crudes : upgrading and marketing

    International Nuclear Information System (INIS)

    Ashar, M.

    2008-01-01

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs

  13. Alberta oil sands crudes : upgrading and marketing

    Energy Technology Data Exchange (ETDEWEB)

    Ashar, M. [Suncor Energy, Fort McMurray, AB (Canada)

    2008-05-15

    Open pit mining and in situ techniques, such as steam stimulation, are used to recover Alberta's bitumen and heavy oil resources, which have higher viscosities than conventional hydrocarbons. The bitumen is typically upgraded to synthetic crude oil (SCO). In the simplest processing scheme, the bitumen is blended with diluent for ease in pipeline transport and then processed at refineries with upgrading facilities. The bitumen is also upgraded to light SCO at world-scale upgraders in Alberta. The SCO is then processed at refineries in downstream markets. The 2 categories of upgrading, notably primary and secondary upgrading, were described in this article along with technology options for both categories. Slurry hydrocracking is regarded as the most interesting emerging residual fuel upgrading technology. It combines special catalyst mixes with the latest slurry reactor designs as well as innovative catalyst capture and recycle schemes to produce very high conversions and potentially superior upgrading economics. The increase in volume and rate of SCO from Alberta provides refiners in the oil sands marketing sector an unprecedented choice of opportunities to improve profitability. Key trends indicate that production will increase substantially from 2008 to 2030. 5 figs.

  14. In situ viscosity of oil sands using low field NMR

    International Nuclear Information System (INIS)

    Bryan, J.; Moon, D.; Kantzas, A.

    2005-01-01

    In heavy oil and bitumen reservoirs, oil viscosity is a vital piece of information that will have great bearing on the chosen EOR scheme and the recovery expected. Prediction of in situ viscosity with a logging tool would he very beneficial in reservoir characterization and exploitation design. Low field NMR is a technology that has shown great potential as a tool for characterizing hydrocarbon properties in heavy oil and bitumen reservoirs. An oil viscosity correlation has previously been developed that is capable of providing order of magnitude viscosity estimates for a wide range of oils taken from various fields in Alberta. This paper presents tuning procedures to improve the NMR predictions for different viscosity ranges, and extends the NMR viscosity model to in situ heavy oil in unconsolidated sands. The results of this work show that the NMR oil peak can be de-convoluted from the in situ signals of the oil and water, and the bulk viscosity correlation that was developed for bulk oils can he applied to predict the in situ oil viscosity. These results can be translated to an NMR logging tool algorithm, allowing for in situ measurements of oil viscosity at the proper reservoir conditions. (author)

  15. A foundation for the future: building an environmental monitoring system for the oil sands

    International Nuclear Information System (INIS)

    Dowdeswell, L.; Dillon, P.; Ghoshal, S.; Miall, A.; Rasmussen, J.; Smol, J.P.

    2010-12-01

    In September, 2010, important concerns regarding the impacts of oil sand industry on the environment in the Lower Athabasca River Basin resulted in the creation of the oil sands advisory panel. This panel was set up to examine and evaluate the existing system for research and monitoring and identify strengths and weaknesses regarding water monitoring in the Lower Athabasca River Basin and connected waterways. In this report, the panel provides important elements to guide the monitoring of water quality and quantity. The panel has identified several organizations or individuals contributing to the research and monitoring of the Athabasca River system but also points out in the document that the research has not yet led to a consensus regarding the impacts of oil sands development on the environment. It has also been observed that no standardized data management system has been put in place to facilitate the access to data for interested parties. Important weaknesses in the existing monitoring system were identified by the panel. The advisory panel recommended the implementation of a credible and transparent, comprehensive and adaptive monitoring program, through a collaborative work between relevant jurisdictions and stakeholders. 50 refs.

  16. Sulfur biogeochemistry of oil sands composite tailings

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Lesley; Stephenson, Kate [Earth Sciences, McMaster University (Canada)], email: warrenl@mcmaster.ca; Penner, Tara [Syncrude Environmental Research (Canada)

    2011-07-01

    This paper discusses the sulfur biogeochemistry of oil sands composite tailings (CT). The Government of Alberta is accelerating reclamation activities on composite tailings. As a CT pilot reclamation operation, Syncrude is currently constructing the first freshwater fen. Minor unpredicted incidents with H2S gas released from the dewatering process associated with these reclamations have been reported. The objective of this study is to ascertain the connection between microbial activity and H2S generation within CT and to assess the sulfur biogeochemistry of untreated and treated (fen) CT over seasonal and annual timescales. The microbial geochemical interactions taking place are shown using a flow chart. CT is composed of gypsum, sand, clay and organics like naphthenic acids and bitumen. Sulfur and Fe cycling in mining systems and their microbial activities are presented. The chemistry and the processes involved within CT are also given along with the results. It can be said that the diverse Fe and S metabolizing microorganisms confirm the ecology involved in H2S dynamics.

  17. 40 CFR 60.591 - Definitions.

    Science.gov (United States)

    2010-07-01

    ....593(c). Petroleum means the crude oil removed from the earth and the oils derived from tar sands..., distillate fuel oils, residual fuel oils, lubricants, or other products through the distillation of petroleum...

  18. Assessing mobility and redistribution patterns of sand and oil agglomerates in the surf zone

    Science.gov (United States)

    Dalyander, P. Soupy; Long, Joesph W.; Plant, Nathaniel G.; Thompson, David M.

    2014-01-01

    Heavier-than-water sand and oil agglomerates that formed in the surf zone following the Deepwater Horizon oil spill continued to cause beach re-oiling 3 years after initial stranding. To understand this phenomena and inform operational response now and for future spills, a numerical method to assess the mobility and alongshore movement of these “surface residual balls” (SRBs) was developed and applied to the Alabama and western Florida coasts. Alongshore flow and SRB mobility and potential flux were used to identify likely patterns of transport and deposition. Results indicate that under typical calm conditions, cm-size SRBs are unlikely to move alongshore, whereas mobility and transport is likely during storms. The greater mobility of sand compared to SRBs makes burial and exhumation of SRBs likely, and inlets were identified as probable SRB traps. Analysis of field data supports these model results.

  19. 40 CFR 60.101 - Definitions.

    Science.gov (United States)

    2010-07-01

    ..., distillate fuel oils, residual fuel oils, lubricants, or other products through distillation of petroleum or... crude oil removed from the earth and the oils derived from tar sands, shale, and coal. (c) Process gas...

  20. Expectations and drivers of future greenhouse gas emissions from Canada's oil sands: An expert elicitation

    International Nuclear Information System (INIS)

    McKellar, Jennifer M.; Sleep, Sylvia; Bergerson, Joule A.; MacLean, Heather L.

    2017-01-01

    The greenhouse gas (GHG) emissions intensity of oil sands operations has declined over time but has not offset absolute emissions growth due to rapidly increasing production. Policy making, decisions about research and development, and stakeholder discourse should be informed by an assessment of future emissions intensity trends, however informed projections are not easily generated. This study investigates expected trends in oil sands GHG emissions using expert elicitation. Thirteen experts participated in a survey, providing quantitative estimates of expected GHG emissions intensity changes and qualitative identifications of drivers. Experts generally agree that emissions intensity reductions are expected at commercially operating projects by 2033, with the greatest reductions expected through the use of technology in the in situ area of oil sands activity (40% mean reduction at multiple projects, averaged across experts). Incremental process changes are expected to contribute less to reducing GHG emissions intensity, however their potentially lower risk and cost may result in larger cumulative reductions. Both technology availability and more stringent GHG mitigation policies are required to realize these emissions intensity reductions. This paper demonstrates a method to increase rigour in emissions forecasting activities and the results can inform policy making, research and development and modelling and forecasting studies. - Highlights: • Expert elicitation used to investigate expected trends in oil sands GHG emissions. • Overall, emissions intensity reductions are expected at commercial projects by 2033. • Reductions are expected due to both technology changes and process improvements. • Technology availability and more stringent GHG policies are needed for reductions. • Method used increases rigour in emissions forecasting, and results inform policy.

  1. Bringing Context to the Oil Sands Debate: understanding the role of nature versus man

    Science.gov (United States)

    Fennell, J.; Gibson, J. J.; Birks, S. J.; YI, Y.; Jasechko, S.; Moncur, M. C.

    2013-12-01

    The Canadian oil sands represent an important resource to the national economy, and a strategic supply-line to the United States of America. These hydrocarbon deposits reside beneath a vast area in northern Alberta, and have been exposed to the environment for millennia as a result of erosion by the Athabasca River and its tributaries. Further complexity to the geochemical setting occurs due to the existence of faulted pathways extending from deeper, highly saline, Devonian intervals to surface. Situated within this natural setting are large waste management structures used to contain mine tailings and oil sands produced water. Many of these structures are situated in close proximity to aquatic receptors and have the potential to affect local water quality due to seepage losses. As such, these structures are coming under increasing scrutiny as a potential source of environmental impact. Discharge of oil sands contaminants to the rivers, and the accumulation of these materials in the Peace-Athabasca Delta, has been cited as a factor leading to adverse health effects at downstream communities. However, the role that natural discharge of contaminants plays has never been fully acknowledged. To address this critical gap, a reconnaissance of the Athabasca River was conducted. Areas of elevated terrain conductivity (detected by EM31 survey) were identified both in background locations and areas suspected of industrial releases. Water samples were collected from various sites and from multiple depth intervals (up to 3 m) within the hyporheic zone of the river sediments. This was achieved using drive-point wells. Each sample was then analyzed for a comprehensive suite of parameters including: i) major ions; ii) dissolved trace elements; iii) dissolved organics; and iv) selected stable and radiogenic isotopes. Results of the investigation identified large areas (in excess of 10km) of groundwater discharge to the Athabasca River well outside the influence of oil sands

  2. Transformation of heavy gas oils derived from oil sands to petrochemical feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Du Plessis, D.; Laureshen, C. [Alberta Energy Research Inst., Edmonton, AB (Canada)

    2006-07-01

    Alberta's petrochemical industry is primarily based on ethane. However, ethane could potentially impede future growth of Alberta's petrochemical industry because of increasing cost and diminishing supplies. Alternately, the rapidly growing oil sands production could provide abundant new feedstocks. Different integration schemes and technologies were evaluated in this study. Research on converting bitumen-derived heavy gas oil into petrochemical feedstock has resulted in the development of two novel technologies and process integration schemes, notably the NOVA heavy oil laboratory catalyst (NHC) process and the aromatic ring cleavage (ARORINCLE) process. This paper described progress to date on these two projects. The paper presented the experimental results for each scheme. For the ARORINCLE process, results were discussed in terms of the effect of process parameters on the hydrogenation step; effect of process parameters on the ring cleavage step; and integrating the upgrading and petrochemical complex. Early laboratory stage results of these two technologies were found to be encouraging. The authors recommended that work should progress to larger scale demonstration of the NHC and ARORINCLE technologies., 13 refs., 2 tabs., 5 figs.

  3. A DEVICE AND METHOD FOR MEASURING TAR IN A TAR-ENVIRONMENT

    DEFF Research Database (Denmark)

    2017-01-01

    The present disclosure describes a device and corresponding method for measuring tar in a tar environment, e.g., a tar producing environment such as a stove or a combustion engine, based on UV absorption spectroscopy. A first measurement along an optical path in the tar environment is performed...

  4. Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India

    Energy Technology Data Exchange (ETDEWEB)

    Suneel, V., E-mail: vasimallas@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Vethamony, P., E-mail: mony@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Naik, B.G., E-mail: bgnaik@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Krishna, M.S., E-mail: moturi@nio.org [CSIR-National Institute of Oceanography, Regional Centre, Visakhapatnam, 530 017 (India); Jadhav, Lakshmikant, E-mail: lakshya87.0@gmail.com [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India)

    2015-09-15

    Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. - Highlights: • Multi-marker approach was effective in identifying the source of tar balls. • n-Alkane DRs show weathering effects even within the core of the tar ball. • Tar balls of the west coast of India since 2012 were derived from Bombay High crude. • Tanker-wash is not the only source of tar balls deposited on the beaches of Goa.

  5. Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India

    International Nuclear Information System (INIS)

    Suneel, V.; Vethamony, P.; Naik, B.G.; Krishna, M.S.; Jadhav, Lakshmikant

    2015-01-01

    Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. - Highlights: • Multi-marker approach was effective in identifying the source of tar balls. • n-Alkane DRs show weathering effects even within the core of the tar ball. • Tar balls of the west coast of India since 2012 were derived from Bombay High crude. • Tanker-wash is not the only source of tar balls deposited on the beaches of Goa

  6. Athabasca--special report No. 2, sand behavior key to operation size

    Energy Technology Data Exchange (ETDEWEB)

    Daly, W J

    1966-09-01

    Before production of the crude oil from the Athabasca tar sands could be initiated, a feasibility and economic study based on field test work was made. It was concluded that the project was technically feasible and a plant could be constructed for approximately $137 million, but that the engineering design must be preceded by a field test program, laboratory work, and by ground surveys. A test program, using the hot water recovery process and sized to handle 3 tons of sand per hour, was begun in Oct. 1963. As the test program proceeded, the unit was frequently renovated as capacity was increased from 3 tons to finally 10 tons per hour. Included in the tests was the determination of the effect that raw bitumen pools (indicated by the government coring program) would have on production operations. It was determined that no problems would arise from this situation because no such pools could be found and were considered not to be in existence. The test model was successful in clearly illustrating the principles to use in the overall layout, which is approximately 50% complete.

  7. Using Epiphytic Lichens to Elucidate the Sources and Spatial Distribution of Inorganic Air Pollution in the Athabasca Oil Sands Region

    Science.gov (United States)

    Landis, M.; Graney, J. R.; Pancras, P.; Krupa, S.; Edgerton, E.; Puckett, K.; Percy, K.

    2013-12-01

    The Wood Buffalo Environmental Association (WBEA) conducted studies to document the geographic patterns of atmospheric deposition of sulfur (S) and nitrogen (N) in the Athabasca Oil Sands Region (AOSR) using epiphytic lichens as bioindicators of atmospheric pollution. Epiphytic lichen samples (Hypogymnia physodes) were collected from 44 locations in 2002, 359 locations in 2008, and 21 locations in 2011 within the AOSR. A subset of samples from 2002 (15) and 2008 (121); and all the samples from 2011 were microwave extracted and analyzed for a comprehensive suite of trace elements using DRC-ICPMS. In addition, source profiles were developed for samples from a variety of available process stacks, heavy duty diesel fleet vehicles, bulk materials representing the various stages of oil sands processing operations, and forest fires. The lichen monitoring and source profile information were integrated into a receptor modeling framework to elucidate the relative importance of natural and anthropogenic sources to the observed atmospheric deposition of S and N in the AOSR. U.S. EPA implemented statistical receptor models utilized included Positive Matrix Factorization (PMF), Unmix, and Chemical Mass Balance (CMB). The sources uniquely identified that significantly contributed to concentrations of elements in the lichen tissue include: fugitive dust from haul roads, tailing sand, and oil sand mining; oil sand processing; combustion processes; and a general urban regional source. The spatial patterns of CMB, PMF, and Unmix receptor model estimated source impacts on the Hypogymnia physodes tissue concentrations from the oil sand processing and fugitive dust sources had a significant association with the distance from the primary oil sands surface mining operations and related production facilities. The spatial extent of the fugitive dust impact was limited to an approximately 20 km radius around the major mining and oil production facilities, indicative of ground level coarse

  8. Successful water management for the oil sands industry

    International Nuclear Information System (INIS)

    Braun, B.

    2003-01-01

    Water is a key requirement to produce oil from thermal oil sands projects. Historically, water was considered as a renewable resource that could be used when necessary. Water use is currently examined in a wider context. Canadian Natural Resources Limited has used fresh water for thermal projects in the past, including its thermal operations at Primrose and Wolf Lake. However, technical advancements have made it possible to use recycled water. This allows companies to survive within their licenses while increasing production. Other advances include the use of brackish water, and innovations such as using depleted reservoir sections to store water to increase the use of recycled water. It was noted that brackish water resources need to be mapped and understood in greater detail. The objective is to use brackish water at a cost equal to, or less, than fresh water

  9. INCREASING WATERFLOOD RESERVES IN THE WILMINGTON OIL FIELD THROUGH IMPROVED RESERVOIR CHARACTERIZATION AND RESERVOIR MANAGEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Scott Walker; Chris Phillips; Roy Koerner; Don Clarke; Dan Moos; Kwasi Tagbor

    2002-02-28

    This project increased recoverable waterflood reserves in slope and basin reservoirs through improved reservoir characterization and reservoir management. The particular application of this project is in portions of Fault Blocks IV and V of the Wilmington Oil Field, in Long Beach, California, but the approach is widely applicable in slope and basin reservoirs. Transferring technology so that it can be applied in other sections of the Wilmington Field and by operators in other slope and basin reservoirs is a primary component of the project. This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate. Although these reservoirs have been waterflooded over 40 years, researchers have found areas of remaining oil saturation. Areas such as the top sand in the Upper Terminal Zone Fault Block V, the western fault slivers of Upper Terminal Zone Fault Block V, the bottom sands of the Tar Zone Fault Block V, and the eastern edge of Fault Block IV in both the Upper Terminal and Lower Terminal Zones all show significant remaining oil saturation. Each area of interest was uncovered emphasizing a different type of reservoir characterization technique or practice. This was not the original strategy but was necessitated by the different levels of progress in each of the project activities.

  10. Sediment oxygen demand of wetlands in the oil sands region of north-eastern Alberta

    International Nuclear Information System (INIS)

    Slama, C.; Ciborowski, J.J.; Gardner Costa, J.

    2009-01-01

    Reclaimed land in the Alberta oil sands mining area contains both reference and oil sands process-affected wetlands constructed using varying sediment compositions. The sediments derived from oil sands process materials (OSPM) may alter the biochemical reactions that take place and affect the sediment oxygen demand (SOD), which is a key factor that contributes to oxygen depletion. This presentation reported on a study in which SOD was measured in a suite of constructed wetlands of different ages, with or without OSPM and topsoil. The purpose of the study was to clarify the role of SOD in wetland function and in the reclamation process. Dissolved oxygen loggers were inserted into dome-shaped chambers on the sediment to measure changes in oxygen demand. Complementary measurements of respiration (CO 2 elution) were used to quantify the biological sediment oxygen demand (BSOD) component of SOD. The chemical sediment oxygen demand (CSOD) was then determined by subtraction from SOD. Wetlands reclaimed using OSPM are expected to have a lower BSOD to CSOD ratio than reference wetlands. Residual ammonia in OSPM sediments may react with sulphate and bind phosphorus. This reduces phosphorus bioavailability and may impede submergent macrophyte growth. As such, wetlands affected by CSOD will have fewer submerged macrophytes than BSOD dominant wetlands.

  11. Next-Generation Sequencing Assessment of Eukaryotic Diversity in Oil Sands Tailings Ponds Sediments and Surface Water.

    Science.gov (United States)

    Aguilar, Maria; Richardson, Elisabeth; Tan, BoonFei; Walker, Giselle; Dunfield, Peter F; Bass, David; Nesbø, Camilla; Foght, Julia; Dacks, Joel B

    2016-11-01

    Tailings ponds in the Athabasca oil sands (Canada) contain fluid wastes, generated by the extraction of bitumen from oil sands ores. Although the autochthonous prokaryotic communities have been relatively well characterized, almost nothing is known about microbial eukaryotes living in the anoxic soft sediments of tailings ponds or in the thin oxic layer of water that covers them. We carried out the first next-generation sequencing study of microbial eukaryotic diversity in oil sands tailings ponds. In metagenomes prepared from tailings sediment and surface water, we detected very low numbers of sequences encoding eukaryotic small subunit ribosomal RNA representing seven major taxonomic groups of protists. We also produced and analysed three amplicon-based 18S rRNA libraries prepared from sediment samples. These revealed a more diverse set of taxa, 169 different OTUs encompassing up to eleven higher order groups of eukaryotes, according to detailed classification using homology searching and phylogenetic methods. The 10 most abundant OTUs accounted for > 90% of the total of reads, vs. large numbers of rare OTUs (< 1% abundance). Despite the anoxic and hydrocarbon-enriched nature of the environment, the tailings ponds harbour complex communities of microbial eukaryotes indicating that these organisms should be taken into account when studying the microbiology of the oil sands. © 2016 The Author(s) Journal of Eukaryotic Microbiology © 2016 International Society of Protistologists.

  12. Effects of Microwave Radiation on Oil Recovery

    Science.gov (United States)

    Esmaeili, Abdollah

    2011-12-01

    A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

  13. Oil Sands Regional Aquatics Monitoring Program (RAMP) 5 year report

    International Nuclear Information System (INIS)

    Fawcett, K.

    2003-05-01

    This 5 year report outlined and examined the activities of the Regional Aquatics Monitoring Program (RAMP) from its introduction in 1997 up to 2001. The RAMP is a multi-stakeholder program comprised of industry and government representatives as well as members of aboriginal groups and environmental organizations. The objectives of RAMP are to monitor aquatic environments in the oil sands region in order to allow for assessment of regional trends and cumulative effects, as well as to provide baseline data against which impact predictions of recent environmental impact assessments can be verified. Scientific programs conducted as part of RAMP during the 5-year period included water quality and sediment quality analyses; fish monitoring; benthic communities monitoring; water quality and aquatic vegetation analyses of wetlands; and hydrology and climate monitoring. RAMP's programs have expanded annually in scope as a result of increased oil sands development in the region. This report provided outlines of RAMP's individual program objectives and organizational structures, as well as details of all studies conducted for each year. Data were collected for all major study areas were presented, and program methodologies for assessing and identifying trends were outlined. refs., tabs., figs

  14. Report and recommendations of the task force on tree and shrub planting on active oil sands tailings dams

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-02-15

    In oil sands reclamation operations in Canada there is a conflict between dam safety and the planting of trees and woody shrubs. Indeed, tree planting is being restricted on the downstream slopes of dams to avoid damage to drains and to ensure the integrity of visual and instrumentation monitoring conflicting thus with progressive reclamation. Alberta Environment hired the Oil Sands Research and Information Network (OSRIN), an independent organization which analyzes and interprets available knowledge on soil and water reclamation in the oil sands mining sector, to address this issue and make recommendations. The organization appointed a Task Force which presented its final report in March 2011. The Task Force recommended that the Engineer of Record should be responsible for determining the tree and shrub planting zones and that he should submit his plans to Alberta Environment for approval.

  15. Development of a bioassay to assess the toxicity of oil sands sediments to pike (Esox lucius)

    Energy Technology Data Exchange (ETDEWEB)

    Turcotte, D.; Yuan, H.; Tumber, V.; Parrott, J. [Environment Canada, Ottawa, ON (Canada); Raine, J. [Saskatchewan Univ., Saskatoon, SK (Canada)

    2010-07-01

    Pike (Esox lucius) are a commercially sought fish species that inhabit the Athabasca River, which flows through the Athabasca oil sands. The fish are exposed to natural sources of bitumen from the McMurray formation. This study was conducted to design and implement a daily-renewal bioassay to assess the toxicity of oil sands to this fish species and to obtain information regarding the development of pike exposed to bitumen. Eggs were collected and fertilized with milt from spawning wild pike captured from Lake Diefenbaker in Saskatchewan. The fertilized eggs were exposed to different concentrations of sediments or culture water only (negative controls) until complete yolk absorption of control fish, approximately 15 days post-hatch. For the rest of the experiment, brine shrimp were fed to the walleye embryos every day after hatching. The developing fish were examined for morphological deformities, survival, hatching success, and changes in weight and length. The research findings indicated that pike is less sensitive than walleye and fathead minnow to the toxicity of oil sands sediments.

  16. Investigating salt and naphthenic acids interactions in the toxicity of oil sands process water to freshwater invertebrates

    International Nuclear Information System (INIS)

    Turcotte, D.; Kautzman, M.; Wojnarowicz, P.; Cutter, J.; Bird, E.; Liber, K.

    2010-01-01

    The hot water extraction process used to produce bitumens from oil sands produces a large volume of oil sands process water (OSPW) that contain elevated concentrations of naphthenic acids (NA) and salts. Many oil sands reclamation projects are proposing the use of OSPW as part of reconstructed wetlands projects. This study investigated the toxicity of OSPW to freshwater invertebrates. The toxic interactions between NA and salinity on freshwater invertebrates were assessed. Bioassays with laboratory-cultured Ceriodaphnia dubia were conducted to determine the toxicity of OSPW from selected water bodies. The study showed that while the concentrations of NAs and salinity were elevated in OSPW waters that caused toxic responses, the concentrations of salinity ions varied greatly among the OSPW samples. Results of the study suggested that ion composition may be a factor in toxicity. Interactions between NAs and salinity were then assessed by performing bioassays with mixtures representing major ion combinations in OSPW.

  17. Compromised metamorphosis and thyroid hormone changes in wood frogs (Lithobates sylvaticus) raised on reclaimed wetlands on the Athabasca oil sands

    International Nuclear Information System (INIS)

    Hersikorn, Blair D.; Smits, Judit E.G.

    2011-01-01

    The wet landscape approach to oil sands tailings reclamation in the Athabasca Oil Sands region involves creating wetlands from fluid tailings in mined-out pits. We measured time to metamorphosis, thyroid hormone status, and detoxification enzyme (EROD) induction in Wood frog (Lithobates sylvaticus) tadpoles raised on reclaimed oil sands wetlands of different ages [young (≤7 yr) vs. old (>7 yr)] and compared data with tadpoles raised on reference (control) wetlands. Metamorphosis was delayed or never occurred in tadpoles raised in young tailings; those exposed to older tailings developed similarly to those in reference wetlands. Thyroid hormone disruption likely played an important role in the metamorphosis delay as the T3:T4 ratio was lowest in tadpoles raised in young, tailings-affected wetlands. Our findings suggest tailings wetlands become less toxic with age, and that these amphibians will be able to complete their life cycle in tailing wetlands that have sufficiently detoxified with age. - This work provides guidance for reclamation of oil sands tailings and shows the usefulness of frogs and caging studies in environmental toxicology.

  18. Compromised metamorphosis and thyroid hormone changes in wood frogs (Lithobates sylvaticus) raised on reclaimed wetlands on the Athabasca oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Hersikorn, Blair D., E-mail: blair.hersikorn@usask.c [Toxicology Centre, University of Saskatchewan, 44 Campus Drive, Saskatoon, Saskatchewan, S7N 5B3 (Canada); Smits, Judit E.G., E-mail: judit.smits@ucalgary.c [Faculty of Veterinary Medicine, University of Calgary, 3280 Hospital Drive NW, Calgary, Alberta, T2N 4Z6 (Canada)

    2011-02-15

    The wet landscape approach to oil sands tailings reclamation in the Athabasca Oil Sands region involves creating wetlands from fluid tailings in mined-out pits. We measured time to metamorphosis, thyroid hormone status, and detoxification enzyme (EROD) induction in Wood frog (Lithobates sylvaticus) tadpoles raised on reclaimed oil sands wetlands of different ages [young ({<=}7 yr) vs. old (>7 yr)] and compared data with tadpoles raised on reference (control) wetlands. Metamorphosis was delayed or never occurred in tadpoles raised in young tailings; those exposed to older tailings developed similarly to those in reference wetlands. Thyroid hormone disruption likely played an important role in the metamorphosis delay as the T3:T4 ratio was lowest in tadpoles raised in young, tailings-affected wetlands. Our findings suggest tailings wetlands become less toxic with age, and that these amphibians will be able to complete their life cycle in tailing wetlands that have sufficiently detoxified with age. - This work provides guidance for reclamation of oil sands tailings and shows the usefulness of frogs and caging studies in environmental toxicology.

  19. Oil sands tailings treatment via surface modification of solids with polymers

    Energy Technology Data Exchange (ETDEWEB)

    Soane, D.; Ware, W.; Mahoney, R.; Kincaid, K. [Soane Energy, Cambridge, MA (United States)

    2010-07-01

    Oil sands fine tailings require large containment area and long-term storage. A recent directive has been established to reduce fluid tailings storage by 30 percent by 2012. This PowerPoint presentation described a method of treating oil sands tailings by modifying the surfaces of solids with polymers. The ATA process divided whole tailings into fines and coarse streams. The coarse stream was used to prepare anchor particles with a monolayer of tether polymers. An activator was added to the fine tailings in order to aggregate. The process cause a Velcro-like attraction between the activated fines and the tether-coated anchor particles. The solid ATA matrix trapped the fines and allowed water to drain more easily. Photographs of the process were provided. An analysis of the process demonstrated that 70 percent of the water in the tailings was recovered in less than 5 minutes. The water was clear, with less than 0.2 percent of suspended solids. The process is applicable to live tailings and mature fine tailings (MFT). tabs., figs.

  20. Petro-Canada's oil sands supply outlook

    International Nuclear Information System (INIS)

    Sangster, B.

    2004-01-01

    A report by the Canadian Energy Research Institute suggests that by 2017, production from the Athabasca Oil Sands could reach as high as 3.5 million barrels per day (mbpd), or it could be as low as 1.1 mbpd. This uncertainty in production is due to several variables such as capital costs, project size, reservoir quality, pipeline capacity and workforce productivity. Other factors that influence production include marginal economics, markets and prices, investor confidence, stakeholder concerns and the Kyoto Protocol. The production level that will be achieved by 2017 will depend on how industry address these emerging issues. The author discussed these issues in detail with particular reference to the approach that Petro-Canada has taken to address the challenges. Suggestions to reduce the potential impacts of these challenges were also presented. tabs., figs

  1. Profiling oil sands mixtures from industrial developments and natural groundwaters for source identification.

    Science.gov (United States)

    Frank, Richard A; Roy, James W; Bickerton, Greg; Rowland, Steve J; Headley, John V; Scarlett, Alan G; West, Charles E; Peru, Kerry M; Parrott, Joanne L; Conly, F Malcolm; Hewitt, L Mark

    2014-01-01

    The objective of this study was to identify chemical components that could distinguish chemical mixtures in oil sands process-affected water (OSPW) that had potentially migrated to groundwater in the oil sands development area of northern Alberta, Canada. In the first part of the study, OSPW samples from two different tailings ponds and a broad range of natural groundwater samples were assessed with historically employed techniques as Level-1 analyses, including geochemistry, total concentrations of naphthenic acids (NAs) and synchronous fluorescence spectroscopy (SFS). While these analyses did not allow for reliable source differentiation, they did identify samples containing significant concentrations of oil sands acid-extractable organics (AEOs). In applying Level-2 profiling analyses using electrospray ionization high resolution mass spectrometry (ESI-HRMS) and comprehensive multidimensional gas chromatography time-of-flight mass spectrometry (GC × GC-TOF/MS) to samples containing appreciable AEO concentrations, differentiation of natural from OSPW sources was apparent through measurements of O2:O4 ion class ratios (ESI-HRMS) and diagnostic ions for two families of suspected monoaromatic acids (GC × GC-TOF/MS). The resemblance between the AEO profiles from OSPW and from 6 groundwater samples adjacent to two tailings ponds implies a common source, supporting the use of these complimentary analyses for source identification. These samples included two of upward flowing groundwater collected <1 m beneath the Athabasca River, suggesting OSPW-affected groundwater is reaching the river system.

  2. Identification of causes of oil sands coke leachate toxicity

    International Nuclear Information System (INIS)

    Puttaswamy, N.; Liber, K.

    2010-01-01

    The potential causes of oil sands coke leachate toxicity were investigated. Chronic 7-day toxicity tests were conducted to demonstrate that oil sands coke leachates (CL) are acutely toxic to Ceriodaphnia dubia (C. dubia). CLs were generated in a laboratory to perform toxicity identification evaluation (TIE) tests in order to investigate the causes of the CL toxicity. The coke was subjected to a 15-day batch leaching process at 5.5 and 9.5 pH values. The leachates were then filtered and used for chemical and toxicological characterization. The 7-day estimates for the C. dubia survival were 6.3 for a pH of 5.5 and 28.7 per cent for the 9.5 CLs. The addition of EDTA significantly improved survival and reproduction in a pH of 5.5 CL, but not in a pH of 9.5 CL. The toxicity of the pH 5.5 CL was removed with a cationic resin treatment. The toxicity of the 9.5 pH LC was removed using an anion resin treatment. Toxicity re-appeared when nickel (Ni) and vanadium (V) were added back to the resin-treated CLs. Results of the study suggested that Ni and V were acting as primary toxicants in the pH 5.5 CL, while V was the primary cause of toxicity in the pH 9.5 CL.

  3. Centrifuge - dewatering of oil sand fluid tailings: phase 2 field-scale test

    Energy Technology Data Exchange (ETDEWEB)

    Seto, Jack T.C. [BGC Engineering Inc (Canada); O' Kane, Mike [O' Kane Consultants Inc (Canada); Donahue, Robert [Applied Geochemical Solutions Engineering (Canada); Lahaie, Rick [Syncrude Canada Ltd (Canada)

    2011-07-01

    In order to reduce the accumulation of oil sand fluid fine tailings (FFT) and to create trafficable surfaces for reclamation, Syncrude Canada Ltd. has been studying several tailings technologies. Centrifuge-dewatering is one such technology. This paper discusses the phase 2 field-scale tests for centrifuge-dewatering of oil sand FFT. In centrifuge-dewatering, FFT is diluted and treated with flocculant, then processed through a centrifuge plant and the high-density underflow is transported to a tailings deposit. This technology has evolved since 2005 from laboratory bench scale tests. More than 10,000 cubic meters of centrifuge cake was treated, produced and transported to ten different deposits over a 12-week period from August to October 2010. The amount of solids in FFT was increased from 30% to 50% by centrifuging. Sampled deposits were tested and instrumented for in situ strength. It can be concluded that the deposits can be strengthened and densified by natural dewatering processes like freeze-thaw action and evaporative drying.

  4. The development of today's mineable oil sands projects, the key factors influencing economics

    International Nuclear Information System (INIS)

    Lynn, J.R.

    1991-01-01

    Many factors influence the perception of economic performance for developing projects. Some of these factors can be controlled by the developer, while some are outside the developer's sphere of influence. Technology selection, management systems, stakeholder involvement, environmental responsiveness and risk management are areas that may be influenced, however interest rates, product prices and currency exchange all have a measurable effect on project economics and are beyond a developer's control. Economic considerations for evaluating mineable oil sand development projects are outlined, focussing on the key factors unique to such developments in general and to the OSLO project in particular. The OSLO project is a proposed $5 billion energy development that entails constructing an open pit oil sands mine and a bitumen extraction facility north of Fort McMurray, Alberta, coupled with a bitumen upgrader in the Redwater area. 7 figs

  5. Enhanced ex situ bioremediation of crude oil contaminated beach sand by supplementation with nutrients and rhamnolipids.

    Science.gov (United States)

    Nikolopoulou, M; Pasadakis, N; Norf, H; Kalogerakis, N

    2013-12-15

    Mediterranean coastal regions are particularly exposed to oil pollution due to extensive industrialization, urbanization and transport of crude and refined oil to and from refineries. Bioremediation of contaminated beach sand through landfarming is both simple and cost-effective to implement compared to other treatment technologies. The purpose of the present study was to investigate the effect of alternative nutrients on biodegradation of crude oil contaminated beach sand in an effort to reduce the time required for bioremediation employing only indigenous hydrocarbon degraders. A natural sandy soil was collected from Agios Onoufrios beach (Chania, Greece) and was contaminated with weathered crude oil. The indigenous microbial population in the contaminated sand was tested alone (control treatment) or in combination with inorganic nutrients (KNO3 and K2HPO4) to investigate their effects on oil biodegradation rates. In addition, the ability of biosurfactants (rhamnolipids), in the presence of organic nutrients (uric acid and lecithin), to further stimulate biodegradation was investigated in laboratory microcosms over a 45-day period. Biodegradation was tracked by GC/MS analysis of aliphatic and polycyclic aromatic hydrocarbons components and the measured concentrations were corrected for abiotic removal by hopane normalizations. It was found that the saturated fraction of the residual oil is degraded more extensively than the aromatic fraction and the bacterial growth after an incubation period of approximately 3 weeks was much greater from the bacterial growth in the control. The results show that the treatments with inorganic or organic nutrients are equally effective over almost 30 days where C12-C35n-alkanes were degraded more than 97% and polyaromatic hydrocarbons with two or three rings were degraded more than 95% within 45 days. The results clearly show that the addition of nutrients to contaminated beach sand significantly enhanced the activity of

  6. Finite element analysis of a model scale footing on clean and oil contaminated sand

    International Nuclear Information System (INIS)

    Evgin, E.; Boulon, M.; Das, B.M.

    1995-01-01

    The effects of oil contamination on the behavior of a model scale footing is determined. Tests are carried out with both clean and oil contaminated sand. The data show that the bearing capacity of the footing is reduced significantly as a result of oil contamination. A finite element analysis is performed to calculate the bearing capacity of the footing and the results are compared with the experimental data. The significance of using an interface element in the analysis is discussed

  7. The state of oil sands wetland reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Foote, L. [Alberta Univ., Edmonton, AB (Canada)

    2010-07-01

    The state of oil sand and wetlands reclamation was the subject of this presentation. Wildlife habitat and response, plant community and production, and microbial biology were examples of research areas surrounding this body of knowledge. Hydrological research and landscape ecology were discussed along with peatlands and marshes such as the Corvette and the Kia. A few examples of what has been learned in the area of wetlands reclamation was presented. Other topics were also discussed, such as timeframes, pragmatic policy approaches, reclamation costs, research needs and some ideas on maturing the field. It was concluded that environmental conditions change with time and area because of time, chemistry, physics, stoichiometry, as well as biotic mediation and facilitation. figs.

  8. Proceedings of the Canadian Institute's 4. annual oil sands supply and infrastructure conference : maximizing opportunity and mitigating risks in a rapidly growing market

    International Nuclear Information System (INIS)

    2006-01-01

    This conference addressed the challenges facing oil sands development, with particular reference to supply and infrastructure issues. Updates on oil sands markets and opportunities were presented along with strategies for mitigating risks in a rapidly growing market. The best practices for supplying a demanding market through supply shortages and high prices were identified along with policies that should be implemented to help overcome labour shortages. Some presentations expressed how commodities pricing and trends can impact business. Others showed how markets in China and the United States are prepared for oilsands products. The views of other international companies on oil sands was also discussed along with proposed plans to eliminate the infrastructure congestion and risks caused by expanding oil sands development. The challenges and benefits of investing in Alberta's oil sands were reviewed along with strategies to enhance upgrading and refining capacity in the province. Economic drivers and the creation of new markets were examined, and various export opportunities were reviewed along with industry management challenges concerning human resources, labour supply, training and education. The conference featured 10 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs

  9. Relating zoobenthic and emergent terrestrial insect production to tree swallow (Tachycineta bicolor) nestling diet in oil sands wetlands

    Energy Technology Data Exchange (ETDEWEB)

    Thoms, J.L.; Martin, J.P.; Ciborowski, J.J. [Windsor Univ., Windsor, ON (Canada); Harms, N.J.; Smits, J.E. [Saskatchewan Univ., Saskatoon, SK (Canada)

    2009-07-01

    This study examined the influence of oil sands process materials (OSPM) on wetland macroinvertebrate community composition and production. Tree swallows are known to inhabit constructed nest boxes and forage near their nest on flying insects of terrestrial and aquatic origin. Therefore, this study evaluated the structure of wetland food webs and how it relates to the transfer of production from aquatic sediments to nestling tree swallows. The study involved 2 reference and 2 oil sands affected wetlands. Exuviae of emerging aquatic and flying insects from floating and sticky traps were collected every 3 days during the tree swallow nestling period in order to estimate benthic invertebrate composition and production. The tree swallow nest boxes, placed around the perimeter of the wetlands in spring were monitored during egg laying and incubation. Diets of the 10-14 day-old nestlings were determined by placing a ligature around the neck of each nestling, preventing the passage of food into the esophagus for 45 min. Food boluses were collected from nestlings fed by the parents during that time. The study showed that although oil sands-affected wetlands had lower aerial insect abundance, they represented over half of the total boluses collected. It was concluded that this study will help determine the ecological viability of oil sands-affected wetlands and their capability of supporting terrestrial predators that rely on zoobenthos.

  10. Plucking the Golden Goose: Higher Royalty Rates on the Oil Sands Generate Significant Increases in Government Revenue

    Directory of Open Access Journals (Sweden)

    Kenneth J. McKenzie

    2011-09-01

    Full Text Available The Alberta government’s 2009 New Royalty Framework elicited resistance on the part of the energy industry, leading to subsequent reductions in the royalties imposed on natural gas and conventional oil. However, the oil sands sector, subject to different terms, quickly accepted the new arrangement with little complaint, recognizing it as win-win situation for industry and the government. Under the framework, Alberta recoups much more money in royalties — about $1 billion over the two year period of 2009 and 2010 — without impinging significantly on investment in the oil sands. This brief paper demonstrates that by spreading the financial risks and benefits to everyone involved, the new framework proves it’s possible to generate increased revenue without frightening off future investment. The same model could conceivably be applied to the conventional oil and natural gas sectors.

  11. The Impact of Foreign Investment Restrictions on the Stock Returns of Oil Sands Companies

    Directory of Open Access Journals (Sweden)

    Eugene Beaulieu

    2014-06-01

    Full Text Available In December 2012, prompted by the proposed purchase of Nexen by the Chinese SOE CNOOC, the federal government announced revised guidelines for investments by state-owned enterprises (SOEs in the oil sands. Declaring the sale marked “the end of a trend and not the beginning of a trend,” Prime Minister Stephen Harper explained how the government would approach such decisions in the future, including placing the onus on foreign investors to demonstrate how deals would be of net benefit to Canada, as well as granting the industry minister the discretion to accept or deny proposed deals. Accounting for five per cent of Canadian GDP, $28 billion in government revenue and three per cent of all jobs nationwide, the oil sands are an integral component of Canada’s economy. The sector has long relied on foreign capital to finance projects, meaning that any move to deter outside investment could have profound consequences for the development of this critical economic asset. In this paper, the authors examine the impact of this policy change by measuring the stock returns of firms operating in the oil sands. Employing an event study analysis, they find empirical evidence that the government’s policy change has resulted in the material destruction of shareholder wealth, particularly in the case of the smaller oil companies. What is more, given the composition of the global oil industry has changed to one where SOEs dominate both reserves and production, is this a policy Canada can afford in the long term? “When we say that Canada is open for business, we do not mean that Canada is for sale to foreign governments.” - Prime Minister Stephen Harper, December 7, 2012 “…going forward, the [industry] minister will find the acquisition of control of a Canadian oil-sands business by a state-owned enterprise to be of net benefit, only in an exceptional circumstance.” - Prime Minister Stephen Harper, December 7, 2012 “A year after the new Investment

  12. Detoxification, endocrine, and immune responses of tree swallow nestlings naturally exposed to air contaminants from the Alberta oil sands.

    Science.gov (United States)

    Cruz-Martinez, Luis; Fernie, Kim J; Soos, Catherine; Harner, Tom; Getachew, Fitsum; Smits, Judit E G

    2015-01-01

    Changes in environmental and wildlife health from contaminants in tailings water on the Canadian oil sands have been well-studied; however, effects of air contaminants on wildlife health have not. A field study was conducted to assess biological costs of natural exposure to oil sands-related air emissions on birds. Nest boxes for tree swallows (Tachycineta bicolor) were erected at two sites; within 5 km of active oil sands mining and extraction, and ≥ 60 km south, at one reference site. Passive air monitors were deployed at the nest boxes to measure nitrogen dioxide, sulfur dioxide, ozone, volatile organic compounds, and polycyclic aromatic hydrocarbons (PAHs). Nestlings were examined at day 9 post hatching to assess T cell function and morphometry. At day 14 post hatching, a subset of nestlings was euthanized to measure detoxification enzymes, endocrine changes, and histological alterations of immune organs. Except for ozone, all air contaminants were higher at the two oil sands sites than the reference site (up to 5-fold). Adult birds had similar reproductive performance among sites (p>0.05). Nestlings from industrial sites showed higher hepatic ethoxyresorufin O-dealkylase (EROD) induction (pfeather corticosterone (p>0.6), and no histological alterations in the spleen or bursa of Fabricius (p>0.05). This is the first report examining toxicological responses in wild birds exposed to air contaminants from industrial activity in the oil sands. It is also the first time that small, individual air contaminant monitors have been used to determine local contaminant levels in ambient air around nest boxes of wild birds. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Responsible management of peatlands in Canada, from peat industry to oil sands

    Science.gov (United States)

    Rochefort, Line

    2013-04-01

    Canada harbors one third of the peat resources of the world. Peat is an accumulated organic matter composed of dead and partly decomposed plant material, forming huge deposit through time in wetlands like peatlands and boreal coniferous swamps. Peat is a valuable resource as a growing media and soil amendments, an eco-friendly absorbent, also used as biofilters, for body care and for wastewater treatment. Peatlands also offer valuable ecological services : for example, they are the most efficient terrestrial ecosystem to store carbon on a long-term basis. Their ability to "cool off" the planet warrants a good look at their management. The horticultural peat industry of Canada has invested 22 years in R&D in habitat restoration and is now a strong leader in managing industrial peatlands in a sustainable way. The oil sand industry, which is strongly impacting the wetland landscapes of northern Canada, does realize that it has to reduce its ecological footprint, which is heavily criticized around the world. Decommissioned open mines near Fort McMurray have already begun recreating peatland ecosystems, and some restoration attempts of former oil pads are underway in the Peace River region. But the restoration of the largely disturbed wetland landscape of the oil sands is commanding innovative solutions.

  14. NorthernLights Transmission : bringing competitive cogen energy from the oil sands to west coast markets

    International Nuclear Information System (INIS)

    Hogan, M.J.C.

    2005-01-01

    NorthernLights Transmission is an initiative by TransCanada that proposes 2 major high-voltage direct current (HVDC) transmission lines to bring low cost, fossil fuelled and renewable generation from the Fort McMurray area to growing electricity markets in the Pacific Northwest, Nevada, Arizona and California. This presentation demonstrated why oil sands cogeneration, shipped via NorthernLights Transmission, is a very attractive resource for these markets. It was shown that the best generation resources are tied to natural resources such as coal, wind, oil sands cogeneration and hydro. Both the Pacific Northwest and California markets prefer low carbon dioxide generation. The proposed HVDC transmission lines would maximize the use of existing energy infrastructure corridors and rights-of-way where possible. This paper presented details of the proposed Celilo Project and the Inland Project, and noted that both are attractive from a technical and economic perspective. The transmission line for the Celilo project would originate in Fort McMurray and connect highly efficient cogeneration and other developing forms of generation to growing loads in the Pacific Northwest and northern California. The cogeneration plants will supply steam and electricity to northern Alberta's oil sands developments along with surplus electricity for export. tabs., figs

  15. Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India.

    Science.gov (United States)

    Suneel, V; Vethamony, P; Naik, B G; Krishna, M S; Jadhav, Lakshmikant

    2015-09-15

    Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. An approach to managing cumulative effects to groundwater resources in the Alberta oil sands

    International Nuclear Information System (INIS)

    Fennell, J.; Forrest, Francine; Klebek, Margaret

    2011-01-01

    In the Athabasca region of Northern Alberta, oil sands activity has raised many concerns over how mining and extracting processes might affect groundwater quality and quantity. The groundwater management framework was developed by Alberta Environment to address these concerns by identifying and managing the potential environmental effects of oil sands activity on groundwater in a science-based manner. This paper develops the framework using risk identification and performance monitoring. The decision-making approach was conducted using decision support tools such as modeling, monitoring and management. Results showed the complexity and variability of groundwater conditions in the Athabasca region and pointed out that knowledge in this area is still developing. This paper presented how the groundwater management framework was developed and pointed out that it will have to be updated as new information arrives.

  17. Changes in algal stable isotopes following nutrient and peat amendments in oil sands aquatic reclamation

    International Nuclear Information System (INIS)

    Farwell, A.; Chen, H.; Boutsivongskad, M.; Dixon, D.

    2010-01-01

    The processing of oil sands in Alberta generates large volumes of processed material that must be reclaimed. Processed water and solids (PW/S) contain higher levels of naturally occurring compounds such as naphthenic acids (NAs) and polycyclic aromatic compounds (PACs). Organic carbon and nitrogen are some of the constituents in PW/S that may provide nutrient sources for aquatic reclamation sites as they develop into viable ecosystems. This study was conducted to assess the modifying factors that may affect the stable carbon and nitrogen isotope values of primary production in oil sands aquatic reclamation. Both field-based microcosm studies and laboratory studies were used to evaluate the changes in the growth and stable isotope values of phytoplankton, periphyton and/or filamentous algae along gradients of dissolved organic carbon (DOC), dissolved inorganic carbon (DIC), nitrogen and phosphorus. Various types of reclamation substrates were used in the study, including various combinations of sand, mature fine tailings, peat and process water. Results showed different levels of growth depending on both the water and substrate type. Typically, periphyton from oil sands reclamation sites were more enriched in 15N than the reference site. Periphyton from one site known as the MP site was more enriched in 13C than periphyton from another site know as the Shallow Wetland South Ditch (SWSD). However, periphyton in the demonstration pond (DP) was more 13C depleted than the reference site. Findings from this study indicate that carbon isotopes are influenced by other factors, such as nutrients.

  18. Levels of polycyclic aromatic hydrocarbons and dibenzothiophenes in wetland sediments and aquatic insects in the oil sands area of northeastern Alberta, Canada.

    Science.gov (United States)

    Wayland, Mark; Headley, John V; Peru, Kerry M; Crosley, Robert; Brownlee, Brian G

    2008-01-01

    An immense volume of tailings and tailings water is accumulating in tailings ponds located on mine leases in the oil sands area of Alberta, Canada. Oil sands mining companies have proposed to use tailings- and tailings water-amended lakes and wetlands as part of their mine remediation plans. Polycyclic aromatic hydrocarbons (PAHs) are substances of concern in oil sands tailings and tailings water. In this study, we determined concentrations of PAHs in sediments, insect larvae and adult insects collected in or adjacent to three groups of wetlands: experimental wetlands to which tailings or tailings water had been purposely added, oil sands wetlands that were located on the mine leases but which had not been experimentally manipulated and reference wetlands located near the mine leases. Alkylated PAHs dominated the PAH profile in all types of samples in the three categories of wetlands. Median and maximum PAH concentrations, especially alkylated PAH concentrations, tended to be higher in sediments and insect larvae in experimental wetlands than in the other types of wetlands. Such was not the case for adult insects, which contained higher than expected levels of PAHs in the three types of ponds. Overlap in PAH concentrations in larvae among pond types suggests that any increase in PAH levels resulting from the addition of tailings and tailings water to wetlands would be modest. Biota-sediment accumulation factors were higher for alkylated PAHs than for their parent counterparts and were lower in experimental wetlands than in oil sands and reference wetlands. Research is needed to examine factors that affect the bioavailability of PAHs in oil sands tailings- or tailings water-amended wetlands.

  19. Sulphur extended oil sand mix : paving material for lower transport cost and CO{sub 2} reduction : ASRL Syncrude research project 1995

    Energy Technology Data Exchange (ETDEWEB)

    Aquin d' , G. [Con-Sul Inc., Missoula, MT (United States)

    2010-07-01

    This power point presentation discussed the use of sulphur-enhanced oil sands (SEOS) as a paving mixture. Sulphur has been added to asphaltic bitumen paving processes since the 1850s. Research into sulphur additions has been conducted by various Canadian industry members and institutions. A study in 1995 investigated the use of SEOS as a temporary paving material. The benefits of using SEOS included lower capital costs and lower greenhouse gas (GHG) impacts. Increases in equipment efficiency were also observed. Researchers are now developing mixing protocols and testing various paving materials in relation to temperature regimes and percentages of sulphur. Sand, limestone, coke, and rubber additions are also being evaluated, as well as the behaviour of SEOS in freeze-thaw cycles. To date, the studies have indicated that a 30 percent sulphur, 10 percent sand, and 60 percent oil sand mixture provides optimal compression and behaviour under freeze-thaw conditions. The use of SEOS paving at oil sands mine sites will reduce truck and road maintenance as well as reduce fuel emissions and consumption rates. tabs., figs.

  20. Coal tar in dermatology

    Energy Technology Data Exchange (ETDEWEB)

    Roelofzen, J.H.J.; Aben, K.K.H.; Van Der Valk, P.G.M.; Van Houtum, J.L.M.; Van De Kerkhof, P.C.M.; Kiemeney, L.A.L.M. [Radboud University Nijmegen Medical Center, Nijmegen (Netherlands). Dept. of Dermatology

    2007-07-01

    Coal tar is one of the oldest treatments for psoriasis and eczema. It has anti-inflammatory, antibacterial, antipruritic and antimitotic effects. The short-term side effects are folliculitis, irritation and contact allergy. Coal tar contains carcinogens. The carcinogenicity of coal tar has been shown in animal studies and studies in occupational settings. There is no clear evidence of an increased risk of skin tumors or internal tumors. Until now, most studies have been fairly small and they did not investigate the risk of coal tar alone, but the risk of coal tar combined with other therapies. New, well-designed, epidemiological studies are necessary to assess the risk of skin tumors and other malignancies after dermatological use of coal tar.

  1. On properties of royalty and tax regimes in Alberta's oil sands

    International Nuclear Information System (INIS)

    Plourde, Andre

    2010-01-01

    Simulation models that include royalty and tax provisions are used to examine the distribution between developers and governments of net returns from the development of Alberta's oil sands deposits. A specific focus is to assess the effects on the level and distribution of net revenues associated with a number of changes in assumed revenue and expenditure conditions. Developers typically bear a greater share of the consequences of variations in capital expenditures than they do of changes in operating expenditures, prices, and exchange rates. A comparison across royalty and tax regimes suggest that there is a positive relationship between the level of net revenues estimated to accrue to either developers or governments and the share of the consequences of changes in conditions borne by that party. Some differences across production technologies are noted. The role of the federal government as a fiscal player in oil sands development has shrunk over time. In contrast, under the current regime, the Government of Alberta captures a higher share of net returns and typically bears a greater proportion of the consequences of changes in conditions than at any time since the introduction of an explicit royalty and tax regime in 1997.

  2. Predicting wear of hydrotransport pipelines in oil sand slurries

    Energy Technology Data Exchange (ETDEWEB)

    Been, J.; Lu, B.; Wolodko, J. [Alberta Research Council, Edmonton, AB (Canada); Kiel, D. [Coanda Research and Development Corp., Burnaby, BC (Canada)

    2008-07-01

    An overview of erosion and corrosion methods and techniques was presented. Wear to pipelines is influenced by slurry flow and chemistry; solids loading; and electrochemical interactions. While several experimental techniques have been developed to rank the performance of different pipeline materials, experiments do not currently provide accurate quantitative prediction of pipeline wear in the field. Rotating cylinder electrodes (RCE) and jet impingement methods are used to study the effect of flow velocity on corrosion rate. Slurry pot erosion-corrosion testers are used to rank materials for use in more dilute, less turbulent slurries. Coriolois slurry erosion testers are used to rank the erosion resistance of different pipeline materials. A pilot-scale flow loop is now being constructed by the Alberta Research Council (ARC) in order to replicate wet erosion phenomena in oil sands applications. The flow loop will be used to simulate the field conditions of oil sands pipelines and develop predictive wear data and models. Coulombic shear stress and characteristic wall velocities have been determined using a 2-layer model designed to represent flow as 2 distinct layers. To date, the flow loop pilot study has demonstrated that wear rates in smaller diameter flow loops are not significantly different than larger diameter field installations. Preliminary calculations have demonstrated that the flow loop can be used to accurately simulate the hydrodynamics and wear typically experienced in field slurry flows. 67 refs., 2 tabs., 7 figs.

  3. Durability and regeneration of catalysts of the iron family in hydrogenation of low-temperature tar

    Energy Technology Data Exchange (ETDEWEB)

    Funasaka, W; Yokogawa, C; Hayashi, K; Kawamura, T; Fujita, H; Suga, S

    1949-01-01

    The low-temperature tar consisting of neutral and acidic oils has been reduced under atmospheric pressure between 400/sup 0/ and 500/sup 0/ by using catalysts prepared from Fe-Cr-kieselguhr, yellow ocher, and other material. When the reduction was performed at 480/sup 0/ with the yellow ocher from Niwasaka, Fukushima Prefacture, Japan, the low-temperature tar was easily converted to neutral and light oils and the catalysts could be regenerated by repeated baking and reduction. It is concluded that the commercialization of this reduction process is possible by using a cycle (each takes 20 minutes) composed of catalytic reaction, baking, and reduction of the catalysts.

  4. Oil prices and economic growth

    International Nuclear Information System (INIS)

    Babusiaux, D.; Lescaroux, F.

    2006-01-01

    There is no limit to the sources of hydrocarbons (whether pumped out of the earth or produced in factories) for the next few decades, but there is and will be a need for increasingly complex and costly techniques as the usual sources of petroleum run out. Does this mean that prices will keep on rising? Probably, since environmental costs must be added onto direct costs. The mining of oil out of 'tar sands', for example, or the production of hydrocarbons by the chemical industry will have a significant impact owing to the emission of greenhouse gases. If prices do rise in the short or middle term, the cause will have to do more with the calendar of investments than with the availability of energy and its costs. In the long run however, price hikes are not all that certain. A few points for analyzing and predicting the macro-and micro-economic effects of fluctuating oil prices are discussed. (author)

  5. Real time, real fast : drilling horizontal wells in a heavy oil environment

    Energy Technology Data Exchange (ETDEWEB)

    Balke, S.C.; Rosauer, M.S. [Petrolera Ameriven/Phillips Petroleum, Caracas, (Venezuela)

    2002-07-01

    Eastern Venezuela's Orinoco Tar Belt or the Faja Petrolifera del Orinoco is one of the largest heavy oil fields in the world, containing more than 1.2 trillion barrels of heavy and extra heavy oil with API gravity of 10 to 6. The field is 320 miles long by 40 miles wide and is divided into the Machete, Zuata, Hamaca and Cerro Negro. It has been under production since the 1970s by Venezuela's national oil company, Petroleos de Venezuela SA. The region is only marginally cost effective because of the high costs associated with development. It is expected that the Hamaca Project, which is centrally located in the Orinoco Tar Belt can be effectively and economically developed by applying the latest technology and innovative techniques. Petrolera Ameriven has committed to develop the 250 square mile Hamaca area. The objective is to produce 165,000 acres at rate of 190,000 BOPD for the life of the project. The challenge is that when the oil is cooled and degasified it looks more like a tar or asphalt for paving roads. In addition, the major reservoirs within the field were deposited in low stand and transgressive system tracks consisting of meandering fluvial to fluvial-tidal deltaic deposits. Methods such as logging while drilling (LWD), satellite links and continuous updating and real-time visualization were applied to assess and mitigate risks. These methods made it possible to accurately place the shoe of the build sections for control of well directions. The methods also made it possible to identify sand/shale interfaces, determine the redirection of the drill bit, locate non-pay zones and help plan well paths to optimize production. The technologies developed were also effective in minimizing development costs, thereby improving the financial viability of the project. 1 ref., 16 figs.

  6. Availability of polycyclic aromatic hydrocarbons from lampblack-impacted soils at former oil-gas plant sites in California, USA.

    Science.gov (United States)

    Hong, Lei; Luthy, Richard G

    2007-03-01

    Lampblack-impacted soils at former oil-gas plant sites in California, USA, were characterized to assess the sorption of polycyclic aromatic hydrocarbons (PAHs) and the concentration-dependent effects of a residual oil tar phase on sorption mechanism and availability of PAHs. Nuclear magnetic resonance spectroscopy demonstrated similar aromaticity for both lampblack carbon and the oil tar phase, with pronounced resonance signals in the range of 100 to 150 ppm. Scanning-electron microscopic images revealed a physically distinct oil tar phase, especially at high concentrations in lampblack, which resulted in an organic-like film structure when lampblack particles became saturated with the oil tar. Sorption experiments were conducted on a series of laboratory-prepared lampblack samples to systematically evaluate influences of an oil tar phase on PAH sorption to lampblack. Results indicate that the sorption of PAHs to lampblack exhibits a competition among sorption phases at low oil tar contents when micro- and mesopores are accessible. When the oil tar content increases to more than 5 to 10% by weight, this tar phase fills small pores, reduces surface area, and dominates PAH sorption on lampblack surface. A new PAH partitioning model, Kd = KLB-C(1 - ftar)alpha + ftarKtar (alpha = empirical exponent), incorporates these effects in which the control of PAH partitioning transits from being dominated by sorption in lampblack (KLB-C) to absorption in oil tar (Ktar), depending on the fraction of tar (ftar). This study illustrates the importance of understanding interactions among PAHs, oil tar, and lampblack for explaining the differences in availability of PAHs among site soils and, consequently, for refining site-specific risk assessment and establishing soil cleanup levels.

  7. Characterization and utilization of hydrotreated products produced from the Whiterocks (Utah) tar sand bitumen-derived liquid

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, C.H.; Longstaff, D.C.; Deo, M.D.; Hanson, F.V.; Oblad, A.G.

    1991-12-31

    The bitumen-derived liquid produced in a 4-inch diameter fluidized-bed reactor from the mined and crushed ore from the Whiterocks tar sand deposit has been hydrotreated in a fixed-bed reactor. The purpose was to determine the extent of upgrading as a function of process operating variable. A sulfided nickel-molybendum on alumina hydrodenitrogenation catalyst was used in all experiments. Moderately severe operating conditions were employed; that is, high reaction temperature (617--680 K) high reactor pressure (11.0--17.1 MPa) and low liquid feed rate (0.18--0.77 HSV); to achieve the desired reduction in heteroatom content. Detailed chemical structures of the bitumen-derived liquid feedstock and the hydrotreated total liquid products were determined by high resolution gas chromatography - mass spectrometry analyses. The compounds identified in the native bitumen included isoprenoids; bicyclic, tricycle, and tetracyclic terpenoids; steranes; hopanes; and perhydro-{beta}-carotenes. In addition, normal and branched alkanes and alkenes and partially dehydrogenated hydroaromatics were identified in the bitumen-derived liquid. The dominant pyrolysis reactions were: (1) the dealkylation of long alkyl side chains to form {alpha} - and isoolefins; and (2) the cleavage of alkyl chains linking aromatic and hydroaromatic clusters. Olefinic bonds were not observed in the hydrotreated product and monoaromatic hydrocarbons were the predominant aromatic species. The properties of the jet fuel fractions from the hydrotreated products met most of the jet fuel specifications. The cetane indices indicated these fractions would be suitable for use as diesel fuels.

  8. Characterization and utilization of hydrotreated products produced from the Whiterocks (Utah) tar sand bitumen-derived liquid

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, C.H.; Longstaff, D.C.; Deo, M.D.; Hanson, F.V.; Oblad, A.G.

    1991-01-01

    The bitumen-derived liquid produced in a 4-inch diameter fluidized-bed reactor from the mined and crushed ore from the Whiterocks tar sand deposit has been hydrotreated in a fixed-bed reactor. The purpose was to determine the extent of upgrading as a function of process operating variable. A sulfided nickel-molybendum on alumina hydrodenitrogenation catalyst was used in all experiments. Moderately severe operating conditions were employed; that is, high reaction temperature (617--680 K) high reactor pressure (11.0--17.1 MPa) and low liquid feed rate (0.18--0.77 HSV); to achieve the desired reduction in heteroatom content. Detailed chemical structures of the bitumen-derived liquid feedstock and the hydrotreated total liquid products were determined by high resolution gas chromatography - mass spectrometry analyses. The compounds identified in the native bitumen included isoprenoids; bicyclic, tricycle, and tetracyclic terpenoids; steranes; hopanes; and perhydro-{beta}-carotenes. In addition, normal and branched alkanes and alkenes and partially dehydrogenated hydroaromatics were identified in the bitumen-derived liquid. The dominant pyrolysis reactions were: (1) the dealkylation of long alkyl side chains to form {alpha} - and isoolefins; and (2) the cleavage of alkyl chains linking aromatic and hydroaromatic clusters. Olefinic bonds were not observed in the hydrotreated product and monoaromatic hydrocarbons were the predominant aromatic species. The properties of the jet fuel fractions from the hydrotreated products met most of the jet fuel specifications. The cetane indices indicated these fractions would be suitable for use as diesel fuels.

  9. Treatment of lignite tars, etc

    Energy Technology Data Exchange (ETDEWEB)

    1936-08-07

    A process is described for treating tars such as lignite tar, shale tar, or peat tar, and similar tars, characterized by the fact that the tar is rectified to about 240/sup 0/C and the residue brought to a temperature above 50/sup 0/C after diluting with a product of the type of gasoline or ligroin at about 30/sup 0/C and treated with selective solvents preferably low-boiling phenols and eventually with water.

  10. Experimental research on accelerated consolidation using filter jackets in fine oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Tol van, F.; Yao, Y.; Paaseen van, L.; Everts, B. [Delft Univ. of Technology, Delft (Netherlands). Dept. of Geotechnology

    2010-07-01

    This PowerPoint presentation discussed prefabricated vertical drains used to enhance the dewatering of fine oil sand tailings. Filtration tests conducted with thickened tailings on standard PVD jackets were presented. Potential clogging mechanisms included clogging of the filter jacket by particles, blinding of the jackets by filter cake, the decreased permeability of consolidated tailings around the drain, and the clogging of the filter jacket with bitumen. Polypropylene and polyester geotextiles were tested in a set-up that replicated conditions observed at 5 to 10 meters below mud level in an oil sand tailings pond. A finite strain consolidation model was used to interpret results obtained in the experimental study. The relationship between the void ratio and hydraulic conductivity was investigated. Results of the study showed that neither the bitumen nor the fines in the sludge cause serious blinding of the filter jackets during the 40 day test period. The consolidation process was adequately simulated with the finite strain consolidation model. tabs., figs.

  11. Policy Analysis of Water Availability and Use Issues for Domestic Oil Shale and Oil Sands Development

    Energy Technology Data Exchange (ETDEWEB)

    Ruple, John [Univ. of Utah, Salt Lake City, UT (United States); Keiter, Robert [Univ. of Utah, Salt Lake City, UT (United States)

    2010-03-01

    Oil shale and oil sands resources located within the intermountain west represent a vast, and as of yet, commercially untapped source of energy. Development will require water, and demand for scarce water resources stands at the front of a long list of barriers to commercialization. Water requirements and the consequences of commercial development will depend on the number, size, and location of facilities, as well as the technologies employed to develop these unconventional fuels. While the details remain unclear, the implication is not – unconventional fuel development will increase demand for water in an arid region where demand for water often exceeds supply. Water demands in excess of supplies have long been the norm in the west, and for more than a century water has been apportioned on a first-come, first-served basis. Unconventional fuel developers who have not already secured water rights stand at the back of a long line and will need to obtain water from willing water purveyors. However, uncertainty regarding the nature and extent of some senior water claims combine with indeterminate interstate river management to cast a cloud over water resource allocation and management. Quantitative and qualitative water requirements associated with Endangered Species protection also stand as barriers to significant water development, and complex water quality regulations will apply to unconventional fuel development. Legal and political decisions can give shape to an indeterminate landscape. Settlement of Northern Ute reserved rights claims would help clarify the worth of existing water rights and viability of alternative sources of supply. Interstate apportionment of the White River would go a long way towards resolving water availability in downstream Utah. And energy policy clarification will help determine the role oil shale and oil sands will play in our nation’s future.

  12. Method for production of fuel oils and diesel motor oils free of sediments and with unlimited miscibility

    Energy Technology Data Exchange (ETDEWEB)

    1942-01-13

    A method is described for the production of fuel and diesel oils free of sediments and with unlimited miscibility by their recovery from substances poor in hydrogen, such as tars of fossil carbon, from lignite, from peat, from schist oils, from wood, or tar oils of corresponding extracts, poorly hydrogenated carbohydrates and the like, characterized by the fact that these substances are being subjected without mixing with selective solvents to a chemical purification and then immediately subjected to a redistillation and the obtained distillates being cut with hydrogen-rich oils to obtain normal diesel oils.

  13. Receiving demulsifying agent from the acid tar

    Energy Technology Data Exchange (ETDEWEB)

    Nikitina, A.A.; Belyaeva, A.S.; Kunakova, R.V. [FGBIHE ' Ufa State Academy of Economics and Services' , Ufa (Russian Federation); Movsumzade, E.M. [FGBIHE ' Ufa State Petroleum Technological Univ.' , Ufa (Russian Federation); Lapidus, A.L. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

    2012-07-01

    The processing of wastes of petrochemical production makes it possible to reduce the price of produced commodity of petroleum products substantially. Bitumen, fuel oils, tars and other mixture of heavy organic compounds are widely used in road construction, in paint and cable industries, manufacture of roofing materials, are used as boiler and furnace fuel, fuel for marine diesel engines, raw material for the production of modifying additives, fillers, surfaceactive substances, etc. (orig.)

  14. Tar ball concentrations in the ocean around the Cape of Good Hope before and after a major oil spill

    Energy Technology Data Exchange (ETDEWEB)

    Eagle, G A; Green, A; Williams, J

    1979-11-01

    From August 1977 to August 1978, tar ball concentrations around the southwestern coast of South Africa were sampled. Prior to a tanker collision on December 16, 1977, the area was relatively free of floating tar. Following the collision, tar ball concentrations increased; tar was transported by wind and currents, at average speeds of about 1 km/hr. In areas of slack currents, tar was observed for as long as 8 months after the spill. Results provided information about surface current trends.

  15. Indian coal tars. II

    Energy Technology Data Exchange (ETDEWEB)

    Basu, A N; Bhatnagar, J N; Roy, A K

    1954-01-01

    Laboratory experiments were carried out on these efforts: (1) rank and specific-gravity fractions on tar yield; (2) addition of water to the coal charge, or steam during carbonization, on yield of tar and tar acids; (3) the presence of a cracking agent (shale) with and without steam addition on the yield of tar and tar acids (the particular shale used without steam reduced the yield, and the restricted use of steam brought the yield to the former noncatalyzed level); and (4) catalytic effect of three different samples of shale, firebrick, quartz, coke, and silica-alumina on the cracking of tar acids (the most active were two of the shales, a freshly-prepared coke, and the Al/sub 2/O/sub 3/-SiO/sub 2/ catalysts that gave conversion up to 98%). The products were mainly carbon, aromatic hydrocarbons of the naphthalene series and gases (CO and H/sub 2/). The yield of the tar becomes less as coal of lower specific gravity is used or when higher temperatures are used for carbonization. The mineral matter associated with Indian coals acts as a decomposition catalyst for tar acids, as shown by experiments on the decomposition of PhOH at temperatures above 800/sup 0/.

  16. 40 CFR 60.591a - Definitions.

    Science.gov (United States)

    2010-07-01

    ... means the crude oil removed from the earth and the oils derived from tar sands, shale, and coal. Petroleum refinery means any facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, or other products through the distillation of petroleum, or through the...

  17. Tar bases in low-temperature coal tar

    Energy Technology Data Exchange (ETDEWEB)

    Sugiura, S; Ueno, H; Yokoyama, H

    1951-01-01

    Tar bases were extracted from three fractions, that boil below 260/sup 0/ at 260/sup 0/ to 280/sup 0/, and 280/sup 0/ to 330/sup 0/, respectively, of the low-temperature tar obtained by the carbonization of Ube coal in a Koppers' vertical retort at approximately 750/sup 0/. These were divided, respectively, into three groups, acetate-forming amine, HCl salt-forming bases (I), and CHCl/sub 3/-soluble bases (II), and further fractionally distilled. From the physical and chemical properties of the fractions thus obtained, it was concluded that low-temperature coal tar contained no low boiling pyridine homologues and that, besides higher homologues of pyridine, nonaromatic, more saturated, and less basic compounds of larger atomic weight and smaller refractive index, such as derivatives of pyrrole and indole, also existed as in crude petroleum.

  18. Papers of a Canadian Institute conference : Tapping into new opportunities in oil sands supply and infrastructure : natural gas, diluent, pipelines, cogeneration

    International Nuclear Information System (INIS)

    2003-01-01

    Participants at this conference were provided the opportunity to hear various views of several industry leaders on topics related to oil sands supply and infrastructure. Some of the issues addressed were: the latest project developments and pipeline infrastructure expansion initiatives in the oil sands industry; the growing natural gas supply requirements for oil sands production; how to effectively manage stakeholder issues in the context of rapid growth; an update on the supply and demand balance for diluent; demand for cogeneration and the implications of transmission system congestion; and, market development prospects for heavy crude and the need for additional refinery capacity. The Minister of Alberta Economic Development also made a special presentation. There were fifteen presentations made at the conference, of which nine were indexed separately for inclusion in this database. refs., tabs., figs

  19. Carbon dynamics, food web structure and reclamation strategies in Athabasca oil sands wetlands (CRFAW)

    International Nuclear Information System (INIS)

    Ciborowski, J.; Dixon, G.; Foote, L.; Liber, K.; Smits, J.

    2010-01-01

    This abstract provided details of the Carbon Dynamics, Food Web Structure and Reclamation Strategies in Athabasca Oil Sands Wetlands (CFRAW) program, a collaboration between oil sands industry partners and university laboratories. CFRAW researchers are investigating the effects of mine tailings and process waters on the development, health, and function of wetland communities in post-mining landscapes. The aim of the program is to accurately predict how quickly the reclaimed wetlands will approach conditions seen in reference wetland systems. The program is also examining the effects of hydrocarbons as a surrogate source of carbon after they are metabolized by bacteria. The biological uptake, pathways, and movement through the food web of materials used by the biota in constructed wetlands are also being studied. Flux estimates will be used to determine if wetlands amended with peat will maintain their productivity. A conceptual model of carbon pathways and budgets is also being developed.

  20. Perch population assessment in lakes reclaimed using oil-sands derived material

    International Nuclear Information System (INIS)

    Heuvel, M.R. van den; Dixon, D.G.; Power, M.; Boerger, H.; MacKinnon, M.D.; Meer, T. van

    1995-01-01

    The mining and extraction of petroleum products from oil-sands involves large areas of land and produces enormous volumes of tailings. One possible land reclamation option is to incorporate fine-tailings material into the bottoms of constructed lakes capped with natural surface water. The wet landscape method represents potential risk to aquatic biota-naphthenic acids and PAHs elute from pore water contained in the fine-tailings substrate. In spring 1995 yellow perch were stocked into a large-scale (5ha) experimental pond that consisted of fine-tailings capped with natural water as well as into two other reclaimed ponds that were constructed with oil-sands overburden material. Prior to stocking of perch, ponds had colonized with cyprinids, macrophytes and benthic invertebrates over a two year period. Perch were sampled in fall 1995 for age, condition factor, liver size, gonad size, fecundity, stomach contents, liver mixed-function oxygenase activity (MFO), bile PAH metabolites and plasma steroid hormones. When compared to the source lake, perch in the DP did not show reduced reproductive potential. Perch in all of the reclaimed ponds demonstrated exposure to organic compounds as indicated by marginally induced MFO activity and increased liver size. Exposure to naphthenates and PAHs in water as well as ecological environmental factors will be discussed

  1. Bison and the oil sands industry

    International Nuclear Information System (INIS)

    Pauls, R.W.

    1998-01-01

    Syncrude's Mildred Lake oil sands development project is located within the central boreal mixed wood forest in an area supporting traditional land uses, including trapping and harvesting of wildlife and plant materials by Fort McKay First Nation residents, in a community within 10 km of the Syncrude development. Reclamation requirements and standards in Alberta specify that the reclamation process must restore a landscape capability equivalent to, or better than that existing before disturbance. Syncrude is committed to complying with all provincial requirements and guidelines in all aspects of its business, including land reclamation. A five year research program has been established to determine the feasibility of reclaiming a portion of the landscape to support wood bison and bison subspecies once indigenous to this area. The current project may be expanded as a pilot commercial ranching venture to explore its commercial viability as a business venture by the Fort McKay First nations

  2. Oil companies push in-situ recovery

    International Nuclear Information System (INIS)

    McIntyre, H.

    1977-01-01

    Possibly, a third Athabaska tar-sand plant using surface mining will be built in the 1980's, but future development beyond that point will probably depend on in-situ recovery. The discussion of in-situ recovery focusses on the effect it will have on the Canadian chemical industry, for example, the market for sodium hydroxide. To obtain the highest yields of oil from bitumen, an external source of hydrogen is necessary; for example Syncrude imports natural gas to make hydrogen for desulphurization. Gasification of coal is a possible source of hydrogen. Research on hydrocracking is progressing. Use of a prototype CANDU OCR reactor to raise the hot steam necessary for in-situ recovery has been suggested. Venezuela is interested in Canadian upgrading technology. (N.D.H.)

  3. 40 CFR 60.101a - Definitions.

    Science.gov (United States)

    2010-07-01

    ... or converting the SO2 to a sulfur product. Petroleum means the crude oil removed from the earth and the oils derived from tar sands, shale, and coal. Petroleum refinery means any facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, asphalt (bitumen) or...

  4. Post Retort, Pre Hydro-treat Upgrading of Shale Oil

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, John

    2012-09-30

    Various oil feedstocks, including oil from oil shale, bitumen from tar sands, heavy oil, and refin- ery streams were reacted with the alkali metals lithium or sodium in the presence of hydrogen or methane at elevated temperature and pressure in a reactor. The products were liquids with sub- stantially reduced metals, sulfur and nitrogen content. The API gravity typically increased. Sodi- um was found to be more effective than lithium in effectiveness. The solids formed when sodium was utilized contained sodium sulfide which could be regenerated electrochemically back to so- dium and a sulfur product using a "Nasicon", sodium ion conducting membrane. In addition, the process was found to be effective reducing total acid number (TAN) to zero, dramatically reduc- ing the asphaltene content and vacuum residual fraction in the product liquid. The process has promise as a means of eliminating sulfur oxide and carbon monoxide emissions. The process al- so opens the possibility of eliminating the coking process from upgrading schemes and upgrad- ing without using hydrogen.

  5. Measurements of oxygenated volatile organic compounds in the oil sands region of Alberta

    Science.gov (United States)

    Moussa, S. G.; Leithead, A.; Li, S. M.; Gordon, M.; Hayden, K. L.; Wang, D. K.; Staebler, R. M.; Liu, P.; O'Brien, J.; Mittermeier, R.; Liggio, J.

    2014-12-01

    Oxygenated volatile organic compounds (OVOCs) are ubiquitous in the atmosphere, and represent an important fraction of volatile organic compounds. Additionally some OVOC species may pose health risks. OVOCs can affect the oxidative and radiative budget of the atmosphere since they are precursors to ground level ozone, hydroxyl radicals and secondary organic aerosols (SOA). OVOCs such as methanol, formaldehyde, acetaldehyde, acetone, crotonaldehyde, methylvinylketone (MVK), methylethylketone (MEK) and acrolein can be emitted from anthropogenic and biogenic sources. Additionally, they are the secondary products of the photo-oxidation of hydrocarbons (biogenic and anthropogenic). Understanding the magnitude of these sources is a prerequisite for accurate representations of radical cycling, ozone production and SOA formation in air quality models. The sources of OVOCs in the Alberta Oil Sands (OS) region have not previously been well characterized. In the summer of 2013, airborne measurements of various OVOCs were made in the Athabasca oil sands region between August 13 and September 7, 2013. Proton Transfer Reaction-Time of Flight-Mass Spectrometry (PTR-ToF-MS) was used to measure methanol, formaldehyde, acetaldehyde, acetone, crotonaldehyde, MVK, MEK, acrolein as well as other hydrocarbons. Emission ratios (ER) for several OVOCs (relative to carbon monoxide; CO) were used to estimate direct anthropogenic emissions from OS industrial sources, while the calculated OH radical exposures were used to estimate the production and removal of secondary anthropogenic OVOCs. The results indicate that OVOCs such as acetaldehyde, crotonaldehyde and MVK have both primary and secondary anthropogenic and biogenic sources. However, species such as methanol and acrolein are from biogenic and anthropogenic sources, respectively. The results of this work will help to characterize sources of OVOCs and the factors influencing their atmospheric fate in the Oil Sands region.

  6. New technology for producing petrochemical feedstock from heavy oils derived from Alberta oil sands

    International Nuclear Information System (INIS)

    Oballa, M.; Simanzhenkov, V.; Clark, P.; Laureshen, C.; Plessis du, D.

    2006-01-01

    This paper presented the results of a study demonstrating the feasibility of producing petrochemical feedstock or petrochemicals from vacuum gas oils derived from oil sands. A typical bitumen upgrader flow scheme was integrated with several new technologies and coupled with an ethane/propane cracker. Technologies included steam cracking, fluid catalytic cracking (FCC); and the catalytic pyrolysis process (CPP). The scheme was then integrated with the Nova Heavy Oil Cracking (NHC) technology. The NHC process uses a reactor to perform catalytic cracking followed by a main tower that separates gas and liquid products. Aromatic ring cleavage (ARORINCLE) technology was explored as a method of catalytic treatment. Experimental runs were conducted in a laboratory scale fixed bed reactor. A stacked catalyst bed was used, followed by a zeolite-based noble metal catalyst. Examples from process run results were presented. Results indicated that the NHC technology should be used on an FCC unit technology platform. The ARORINCLE technology was considered for use on a hydrotreating unit technology platform. Once the catalysts are fully developed and demonstrated, the economics of the technologies will be enhanced through the construction of world-scale complexes integrating upgrading, refining and petrochemical plants. refs., tabs., figs

  7. Sea sand disruption method (SSDM) as a valuable tool for isolating essential oil components from conifers.

    Science.gov (United States)

    Dawidowicz, Andrzej L; Czapczyńska, Natalia B

    2011-11-01

    Essential oils are one of nature's most precious gifts with surprisingly potent and outstanding properties. Coniferous oils, for instance, are nowadays being used extensively to treat or prevent many types of infections, modify immune responses, soothe inflammations, stabilize moods, and to help ease all forms of non-acute pain. Given the broad spectrum of usage of coniferous essential oils, a fast, safe, simple, and efficient sample-preparation method is needed in the estimation procedure of essential oil components in fresh plant material. Generally, the time- and energy-consuming steam distillation (SD) is applied for this purpose. This paper will compare SD, pressurized liquid extraction (PLE), matrix solid-phase dispersion (MSPD), and the sea sand disruption method (SSDM) as isolation techniques to obtain aroma components from Scots pine (Pinus sylvestris), spruce (Picea abies), and Douglas fir (Pseudotsuga menziesii). According to the obtained data, SSDM is the most efficient sample preparation method in determining the essential oil composition of conifers. Moreover, SSDM requires small organic solvent amounts and a short extraction time, which makes it an advantageous alternative procedure for the routine analysis of coniferous oils. The superiority of SSDM over MSPD efficiency is ascertained, as there are no chemical interactions between the plant cell components and the sand. This fact confirms the reliability and efficacy of SSDM for the analysis of volatile oil components. Copyright © 2011 Verlag Helvetica Chimica Acta AG, Zürich.

  8. Polymer aids for settling and filtration of oil sands tailings

    Energy Technology Data Exchange (ETDEWEB)

    Wang, X. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; Energy Resources Conservation Board, Calgary, AB (Canada). Oil Sands Section; Xu, Z.; Masliyah, J.H. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

    2008-07-01

    Oil sand tailings are segregated into coarse and fine tailings. High volumes of toxic fluids and tailings are created in the process. Tailings ponds are an environmental risk with high operating and maintenance costs. Current commercial technologies uses chemical additions to create recycled water and composite tailings (CT). Researchers are now investigating centrifuged and dry mature fine tailings (MFT). Filtration processes with flocculants are used to separate the tailings into warm recycle water and dried cakes that can be used in reclamation processes. Studies are being conducted to find a polymer than can effectively flocculate and filter whole oil sands tailings. The filtration procedure uses pressure to produce released water. Polymers include magnafloc and Al-PAM polymer concentrations are used in slurry masses. Tests have been conducted to determine the settling rates of the polymers. The tests showed that Al-PAM filtered the tailings effectively. Paraffinic froth treatment tests have also been conducted to determine settling rates. A cake produced with froth treatment tailings of Al-PAM 400 ppm had a water content 42.5 wt per cent. The tests showed that while Magnafloc 1011 is a good settling aid, but a poor filtration addition. Al-PAM aided in both the flocculation and filtration processes. Higher Al-PAM dosages are needed for froth treatment tailings processes. It was concluded that dry cakes are produced with the addition of Al-PAM. tabs., figs.

  9. Planning for, and measuring, the business value of technology projects in the oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Sayed, M. [Northern Alberta Inst. of Technology, Edmonton, AB (Canada); Burgess, A. [Telus Energy Sector Organization, Calgary, AB (Canada)

    2007-07-01

    This presentation discussed new communications technology options developed for oil sands industry operators. Technology options included broadband access for data, video and voice requirements, as well as new options for video, audio, and web conferencing. Recent technology options for inter-camp communications were presented, as well as new software developments for distance education, video surveillance, and data security. Various entertainment technologies for oil sands camp employees included in-room telephones, internet and gaming access, radio, television, and family web-cams. New electronic permitting equipment was described, and details of security and verification cards and tickets were provided. The economic benefits and social advantages of adopting the technologies were discussed. A research project and assessment tool designed to predict and measure the business value of information technology (IT) and communications technologies and projects was outlined. A case study of the Schlumberger heavy equipment program was used to demonstrate the assessment tool. refs., tabs., figs.

  10. Supercritical fluid extraction of soybean oil from the surface of spiked quartz sand - modelling study

    OpenAIRE

    Stela Jokić; B. Nagy; K. Aladić; B. Simándi

    2013-01-01

    The extraction of soybean oil from the surface of spiked quartz sand using supercritical CO2 was investigated. Sand as solid was used; it is not porous material so the internal diffusion does not exist, all the soluble material is in the surface of the particles. Sovová’s model has been used in order to obtain an analytical solution to develop the required extraction yield curves. The model simplifies when the internal diffusion can be neglected. The external mass transfer coefficient was det...

  11. Key performance indicators for electric mining shovels and oil sands diggability

    Science.gov (United States)

    Patnayak, Sibabrata

    A shovel performance monitoring study was undertaken in two oil sands mines operated by Syncrude Canada Ltd. using performance data obtained from P&H 4100 TS and BOSS electric mining shovels. One year of shovel performance data along with geological, geotechnical, and climatic data were analyzed. The approach adopted was to use current and voltage data collected from hoist and crowd motors and to calculate the energy and/or power associated with digging. Analysis of performance data along with digital video records of operating shovels indicated that hoist and crowd motor voltages and currents can be used to identify the beginning and the end of individual dig cycles. A dig cycle identification algorithm was developed. Performance indicators such as dig cycle time, hoist motor energy and power, and crowd motor energy and power were determined. The shovel performance indicators provide important insight into how geology, equipment and operators affect the digging efficiency. The hoist motor power is a useful key performance indicator for assessing diggability. Hoist motor energy consumption per tonne of material excavated and the number of dig cycles required for loading a truck can be useful key performance indicators for assessing operator performance and productivity. Analysis of performance data along with operators team schedules showed that the performance of a shovel can be significantly influenced by the operator's digging technique while digging uniform material. Up to 25% variability in hoist motor power consumption and 50% variability in productivity was noted between different operators. Shovel type and dipper teeth configuration can also influence the power draw on electrical motors during digging. There is no common agreement existing on the influence of bitumen content on oil sands diggability. By comparing the hoist motor power consumption, it was found that the rich ore was more difficult to dig than the lean ore. Similarly, estuarine ore was more

  12. Supplying synthetic crude oil from Canadian oil sands: A comparative study of the costs and CO2 emissions of mining and in-situ recovery

    International Nuclear Information System (INIS)

    Méjean, Aurélie; Hope, Chris

    2013-01-01

    High crude oil prices and the eventual decline of conventional oil production raise the issue of alternative fuels such as non-conventional oil. The paper describes a simple probabilistic model of the costs of synthetic crude oil produced from Canadian oil sands. Synthetic crude oil is obtained by upgrading bitumen that is first produced through mining or in-situ recovery techniques. This forward-looking analysis quantifies the effects of learning and production constraints on the costs of supplying synthetic crude oil. The sensitivity analysis shows that before 2035, the most influential parameters are the learning parameter in the case of in-situ bitumen and the depletion parameter in the case of mined bitumen. After 2035, depletion dominates in both cases. The results show that the social cost of CO 2 has a large impact on the total costs of synthetic crude oil, in particular in the case of synthetic crude oil from in-situ bitumen, due to the carbon intensity of the recovery techniques: taking into account the social cost of CO 2 adds more than half to the cost of producing synthetic crude oil from mined bitumen in 2050 (mean value), while the cost of producing synthetic crude oil from in-situ bitumen more than doubles. - Highlights: • We model the cost of Canadian synthetic crude oil (SCO) using Monte-Carlo techniques. • We reveal the uncertainty associated with each input parameter. • We quantify the effect of learning, depletion and CO 2 using sensitivity analyses. • Accounting for the social cost of CO 2 doubles the cost of SCO from in-situ bitumen. • CO 2 pricing could have a large effect on the economics of the oil sands

  13. Topical tar: Back to the future

    Energy Technology Data Exchange (ETDEWEB)

    Paghdal, K.V.; Schwartz, R.A. [University of Medicine & Dentistry of New Jersey, Newark, NJ (United States)

    2009-08-15

    The use of medicinal tar for dermatologic disorders dates back to the ancient times. Although coal tar is utilized more frequently in modern dermatology, wood tars have also been widely employed. Tar is used mainly in the treatment of chronic stable plaque psoriasis, scalp psoriasis, atopic dermatitis, and seborrheic dermatitis, either alone or in combination therapy with other medications, phototherapy, or both. Many modifications have been made to tar preparations to increase their acceptability, as some dislike its odor, messy application, and staining of clothing. One should consider a tried and true treatment with tar that has led to clearing of lesions and prolonged remission times. Occupational studies have demonstrated the carcinogenicity of tar; however, epidemiologic studies do not confirm similar outcomes when used topically. This article will review the pharmacology, formulations, efficacy, and adverse effects of crude coal tar and other tars in the treatment of selected dermatologic conditions.

  14. Production of gas and volatile materials by distillation of tars, etc

    Energy Technology Data Exchange (ETDEWEB)

    Arson, M

    1860-04-25

    The principle of this production is in the treating of heavy oils with heat, their transformation occurring nearly completely by the action of this agent. The apparatus used consists of a retort of such a form that it has openings at the two ends immediately opposed to each other. One serves to introduce the oil and the other to remove the tar and gas produced. At the exit of the apparatus the gas passes into coolers like those used for coal gas.

  15. Utilization of fly ash as partial sand replacement in oil palm shell lightweight aggregate concrete

    Science.gov (United States)

    Nazrin Akmal, A. Z. Muhammad; Muthusamy, K.; Mat Yahaya, F.; Hanafi, H. Mohd; Nur Azzimah, Z.

    2017-11-01

    Realization on the increasing demand for river sand supply in construction sector has inspired the current research to find alternative material to reduce the use of natural sand in oil palm shell lightweight aggregate concrete (OPS LWAC) production. The existence of fly ash, a by-product generated from coal power plant, which pose negative impact to the environment when it is disposed as waste, were used in this research. The effect of fly ash content as partial sand replacement towards workability and compressive strength of OPS lightweight aggregate concrete were investigated. Four concrete mixes containing various percentage of fly ash that are 0%, 10%, 20% and 30% by weight of sand were used in the experimental work. All mixes were cast in form of cubes before subjected to water curing until the testing age. Compressive strength test were conducted at 1, 3, 7 and 28 days. The finding shows that the workability of the OPS LWAC decreases when more fly ash are used as sand replacement. It was found that adding of 10% fly ash as sand replacement content resulted in better compressive strength of OPS LWAC, which is higher than the control mix.

  16. Trace metal mobilization from oil sands froth treatment thickened tailings exhibiting acid rock drainage.

    Science.gov (United States)

    Kuznetsova, Alsu; Kuznetsov, Petr; Foght, Julia M; Siddique, Tariq

    2016-11-15

    Froth treatment thickened tailings (TT) are a waste product of bitumen extraction from surface-mined oil sands ores. When incubated in a laboratory under simulated moist oxic environmental conditions for ~450d, two different types of TT (TT1 and TT2) exhibited the potential to generate acid rock drainage (ARD) by producing acid leachate after 250 and 50d, respectively. We report here the release of toxic metals from TT via ARD, which could pose an environmental threat if oil sands TT deposits are not properly managed. Trace metal concentrations in leachate samples collected periodically revealed that Mn and Sr were released immediately even before the onset of ARD. Spikes in Co and Ni concentrations were observed both pre-ARD and during active ARD, particularly in TT1. For most elements measured (Fe, Cr, V, As, Cu, Pb, Zn, Cd, and Se), leaching was associated with ARD production. Though equivalent acidification (pH2) was achieved in leachate from both TT types, greater metal release was observed from TT2 where concentrations reached 10,000ppb for Ni, 5000ppb for Co, 3000ppb for As, 2000ppb for V, and 1000ppb for Cr. Generally, metal concentrations decreased in leachate with time during ARD and became negligible by the end of incubation (~450d) despite appreciable metals remaining in the leached TT. These results suggest that using TT for land reclamation purposes or surface deposition for volume reduction may unfavorably impact the environment, and warrants application of appropriate strategies for management of pyrite-enriched oil sands tailings streams. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Predicted water quality of oil sands reclamation wetlands : impact of physical design and hydrology

    International Nuclear Information System (INIS)

    2006-01-01

    Although engineered wetlands can be used as treatment systems in the reclamation of oil sands mines, a variety of factors must be considered to improve the biological functioning of many oil sands reclamation landscapes. Key factors in the control of concentrations of dissolved substances include area, depth, shape, surrounding landscape material and contributing water quality and quantity. Seasonal cycles of precipitation and ice cover also require consideration in the planning of wetlands ecosystems. This paper presented details of a model designed to predict constituent concentrations in planned wetlands based on probable inflow and processes. Input variables consisted of key substances and hydrological factors that may be encountered on reclaimed landscapes. The model was constructed to perform sensitivity analyses of wetlands with respect to total dissolved solids (TDS), major ions, and naphthenic acids concentrations. Inputs and assumptions drawn from previous environmental impact assessments completed for proposed and approved oil sands projects were used. Results suggested that wetlands volume is an important factor in the moderation of peak flows and substance decay. The predictions generated by the model suggested that wetlands size, tailings and sandcap placement schedules may be manipulated to achieve desired wetlands salinities. It was observed that the proportion of the watershed covered by specific land types can affect both initial and future concentrations. Long-term climate change that results in 15 per cent more or less runoff was predicted to have little effect on wetlands concentrations, although concentrations may rise during periodic droughts. It was concluded that site-specific modelling and careful planning is needed to achieve desired water quality for the creation of engineered wetlands. 18 refs., 3 tabs., 3 figs

  18. Quantitative determination of acid oils in low-temperature coal tar by means of fractional distillation

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, A

    1950-01-01

    The aromatic hydroxy compounds in low-temperature tar were separated, and 75 compounds in the boiling range 180/sup 0/ to 320/sup 0/ isolated by means of fractional distillation in packed columns of at least 45 theoretical plates. Mixtures not separable by fractionation were separated by means of other physicochemical or chemical methods. Hydroxy compounds with boiling point up to 230/sup 0/C were detemined quantitatively, as were the phenols present in low-temperature carbonization liquors. With the Krupp-Lurgi process of low-temperature carbonization, 1.8% phenol, 1.8% o-cresol, and 3.6% m-p-cresols were formed. The tar contained up to 1.3% 1:3:5-xylenol and up to 0.9% 1:2:4-xylenol. Of the 12.1% v/v of phenol, cresols, and xylenols present in tar, 11.2% were determined quantitatively, and 9 hydroxy compounds were identified in the remaining 0.9%. On the basis of these investigations, a technical plant that permitted the recovery of pure low-temperature tar phenols and the preparation of a number of different phenol resins from the mixtures was erected.

  19. G-CLEAN OSC-1809

    Science.gov (United States)

    Technical product bulletin: aka OIL SPILL CLEANUP, this surface washing agent may be applied liberally to heavily weathered oil on rocks or beaches/sand, vegetation, or at full strength on tar balls. Best results if allowed to soak, agitated, or reapplied.

  20. Removing tar information from cigarette packages may reduce South Korean smokers' misconceptions about low-tar cigarettes

    Directory of Open Access Journals (Sweden)

    Hye-Jin Paek

    2018-03-01

    Full Text Available Background Many smokers still have misconceptions about “light” or “low tar” cigarettes. In South Korea, low-tar (< 3 mg cigarette sales have increased sharply from 1.8% in 2002 to 49.2% in 2015. Although government regulations forbid cigarette packages from displaying messages such as “mild,” “low-tar,” and “light,” numbers indicating tar amounts are still permitted. This study examines whether removing tar information from packaging altogether reduces people's misconceptions about low tar cigarettes. Methods An online experiment was conducted among 531 smokers who were randomly assigned to one of two conditions. In the “tar” condition, 271 participants were shown in random order three cigarette packages for three major brands (Esse, The One, Marlboro with different tar amounts. In the “no-tar” condition, 260 participants were shown the same packages without tar information. Next, participants evaluated which type of cigarette was mildest, least harmful, easier for nonsmokers to start smoking, and easier for smokers to quit. After descriptive statistics were checked, twelve sets of chi-square tests were performed. Results Average age of the participants was 26.22 (14 - 62 years; 53.5% were male. All 12 chi-square tests were statistically significant. Participants in the tar condition judged the lowest-tar cigarette to be mildest, least harmful, easier to start, and easier to quit. In the no-tar condition, for the Korean brands Esse and The One, most respondents evaluated all cigarette types to be the same only for harm, ease of starting, and ease of quitting; for Marlboro, judgments were the same as those in the tar condition except that “easier to quit” was judged to be the same across the three types. Conclusions Banning tar information from cigarette packages may help reduce smokers' misconceptions about low-tar cigarettes. People have inconsistent judgments about differently packaged cigarettes when tar

  1. Differences in phytotoxicity and dissipation between ionized and nonionized oil sands naphthenic acids in wetland plants.

    Science.gov (United States)

    Armstrong, Sarah A; Headley, John V; Peru, Kerry M; Germida, James J

    2009-10-01

    Naphthenic acids (NAs) are composed of alkyl-substituted acyclic and cycloaliphatic carboxylic acids and, because they are acutely toxic to fish, are of toxicological concern. During the caustic hot-water extraction of oil from the bitumen in oil sands deposits, NAs become concentrated in the resulting tailings pond water. The present study investigated if dissipation of NAs occurs in the presence of hydroponically grown emergent macrophytes (Typha latifolia, Phragmites australis, and Scirpus acutus) to determine the potential for phytoremediation of these compounds. Plants were grown with oil sands NAs (pKa approximately 5-6) in medium at pH 7.8 (predominantly ionized NAs) and pH 5.0 (predominantly nonionized NAs) to determine if, by altering their chemical form, NAs may be more accessible to plants and, thus, undergo increased dissipation. Whereas the oil sands NA mixture in its nonionized form was more toxic to wetland plants than its ionized form, neither form appeared to be sequestered by wetland plants. The present study demonstrated that plants may selectively enhance the dissipation of individual nonionized NA compounds, which contributes to toxicity reduction but does not translate into detectable total NA dissipation within experimental error and natural variation. Plants were able to reduce the toxicity of a NA system over 30 d, increasing the median lethal concentration (LC50; % of hydroponic solution) of the medium for Daphnia magna by 23.3% +/- 8.1% (mean +/- standard error; nonionized NAs) and 37.0% +/- 2.7% (ionized NAs) as determined by acute toxicity bioassays. This reduction in toxicity was 7.3% +/- 2.6% (nonionized NAs) and 45.0% +/- 6.8% (ionized NAs) greater than that in unplanted systems.

  2. Phytotoxicity and Plant Productivity Analysis of Tar-Enriched Biochars

    Science.gov (United States)

    Keller, M. L.; Masiello, C. A.; Dugan, B.; Rudgers, J. A.; Capareda, S. C.

    2008-12-01

    Biochar is one of the three by-products obtained by the pyrolysis of organic material, the other two being syngas and bio-oil. The pyrolysis of biomass has generated a great amount of interest in recent years as all three by-products can be put toward beneficial uses. As part of a larger project designed to evaluate the hydrologic impact of biochar soil amendment, we generated a biochar through fast pyrolysis (less than 2 minutes) of sorghum stock at 600°C. In the initial biochar production run, the char bin was not purged with nitrogen. This inadvertent change in pyrolysis conditions produced a fast-pyrolysis biochar enriched with tars. We chose not to discard this batch, however, and instead used it to test the impact of tar-enriched biochars on plants. A suite of phytotoxicity tests were run to assess the effects of tar-rich biochar on plant germination and plant productivity. We designed the experiment to test for negative effects, using an organic carbon and nutrient-rich, greenhouse- optimized potting medium instead of soil. We used Black Seeded Simpson lettuce (Lactuca sativa) as the test organism. We found that even when tars are present within biochar, biochar amendment up to 10% by weight caused increased lettuce germination rates and increased biomass productivity. In this presentation, we will report the statistical significance of our germination and biomass data, as well as present preliminary data on how biochar amendment affects soil hydrologic properties.

  3. Total and methyl mercury concentrations in sediment and water of a constructed wetland in the Athabasca Oil Sands Region

    International Nuclear Information System (INIS)

    Oswald, Claire J.; Carey, Sean K.

    2016-01-01

    In the Athabasca Oil Sands Region in northeastern Alberta, Canada, oil sands operators are testing the feasibility of peatland construction on the post-mining landscape. In 2009, Syncrude Canada Ltd. began construction of the 52 ha Sandhill Fen pilot watershed, including a 15 ha, hydrologically managed fen peatland built on sand-capped soft oil sands tailings. An integral component of fen reclamation is post-construction monitoring of water quality, including salinity, fluvial carbon, and priority pollutant elements. In this study, the effects of fen reclamation and elevated sulfate levels on mercury (Hg) fate and transport in the constructed system were assessed. Total mercury (THg) and methylmercury (MeHg) concentrations in the fen sediment were lower than in two nearby natural fens, which may be due to the higher mineral content of the Sandhill Fen peat mix and/or a loss of Hg through evasion during the peat harvesting, stockpiling and placement processes. Porewater MeHg concentrations in the Sandhill Fen typically did not exceed 1.0 ng L −1 . The low MeHg concentrations may be a result of elevated porewater sulfate concentrations (mean 346 mg L −1 ) and an increase in sulphide concentrations with depth in the peat, which are known to suppress MeHg production. Total Hg and MeHg concentrations increased during a controlled mid-summer flooding event where the water table rose above the ground surface in most of the fen. The Hg dynamics during this event showed that hydrologic fluctuations in this system exacerbate the release of THg and MeHg downstream. In addition, the elevated SO 4 2− concentrations in the peat porewaters may become a problem with respect to downstream MeHg production once the fen is hydrologically connected to a larger wetland network that is currently being constructed. - Highlights: • A constructed fen peatland in the Athabasca Oil Sands Region was studied. • Total and methyl mercury concentrations in fen sediment and waters

  4. Effects of oil sands sediments on fish

    International Nuclear Information System (INIS)

    Parrott, J.; Colavecchia, M.; Hewitt, L.; Sherry, J.; Headley, J.; Turcotte, D.; Liber, K.

    2010-01-01

    This paper described a collaborative project organized by Natural Resources Canada (NRCan) Panel of Energy Research and Development (PERD) with researchers from Environment Canada and the University of Saskatchewan. The 4-year study was conducted to assess the toxicity of oil sands sediments and river waters, and reclamation ponds and sediments on laboratory-raised fish. Three sediments from rivers were evaluated for their potential to cause adverse impacts on fathead minnow eggs and larvae for a period of 18 days. The study monitored hatching, larval survival, development, and growth. Naphthenic acids (NA), polycyclic aromatic hydrocarbons (PAHs) and metals were measured in the sediments to determine if the compounds can be correlated with observed toxicity. The study will also assess walleye eggs exposed to sediments, and in situ fish exposures. Toxicity identification and evaluation (TIE) studies will be conducted to isolate the fractions that may affect fish development and growth.

  5. Characterization of oils sands thickened tailings

    Energy Technology Data Exchange (ETDEWEB)

    Scott, J.D.; Jeeravipoolvarn, S.; Donahue, R.; Ozum, B. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering

    2008-07-01

    This presentation discussed the characterization of oils sands thickened tailings. The problem statement was defined as the fact that many laboratory procedures to characterize fine tailings do not take into account the extraction process, and instead use standardized laboratory tests. The purpose of this presentation was to demonstrate how different extraction processes affect the fine tailings geotechnical properties and water chemistry. Properties that were characterized included particle size analysis from hydrometer-sieve tests; per cent clay from methylene blue tests; per cent clay from mineralogy tests; Atterberg limits; water chemistry; and morphology by scanning electron microscopy. The presentation discussed the origin of fines (silt and clay) in tailings; where fine particles come from; tailings materials; mineralogy of tailings; the hydrometer-sieve test on fine tailings and thickened tailings; and the methylene blue test. It was concluded that the great majority of clay minerals in the tailings come from the clay-shale discontinuous seams and layers. For thickened tailings, the dispersed and non-dispersed hydrometer tests show considerable difference in the amount of clay size material. tabs., figs.

  6. Evaluation of microbial biofilm communities from an Alberta oil sands tailings pond.

    Science.gov (United States)

    Golby, Susanne; Ceri, Howard; Gieg, Lisa M; Chatterjee, Indranil; Marques, Lyriam L R; Turner, Raymond J

    2012-01-01

    Bitumen extraction from the oil sands of Alberta has resulted in millions of cubic meters of waste stored on-site in tailings ponds. Unique microbial ecology is expected in these ponds, which may be key to their bioremediation potential. We considered that direct culturing of microbes from a tailings sample as biofilms could lead to the recovery of microbial communities that provide good representation of the ecology of the tailings. Culturing of mixed species biofilms in vitro using the Calgary Biofilm Device (CBD) under aerobic, microaerobic, and anaerobic growth conditions was successful both with and without the addition of various growth nutrients. Denaturant gradient gel electrophoresis and 16S rRNA gene pyrotag sequencing revealed that unique mixed biofilm communities were recovered under each incubation condition, with the dominant species belonging to Pseudomonas, Thauera, Hydrogenophaga, Rhodoferax, and Acidovorax. This work used an approach that allowed organisms to grow as a biofilm directly from a sample collected of their environment, and the biofilms cultivated in vitro were representative of the endogenous environmental community. For the first time, representative environmental mixed species biofilms have been isolated and grown under laboratory conditions from an oil sands tailings pond environment and a description of their composition is provided.

  7. Effects of oil sands waste water on the wood frog (rana sylvatica)

    Energy Technology Data Exchange (ETDEWEB)

    Hersikorn, B.; Smits, J.E. [Saskatchewan Univ., Regina, SK (Canada)

    2007-07-01

    The sustainability of various reclamation strategies can be determined by the growth and health of indigenous amphibians (Wood Frogs). This paper referred to the large quantities of tailings water that are generated by oil sand extraction activities. It presented the results of a study that was conducted in the spring and summer of 2006 and 2007 on reclaimed formation wetlands comprising tailings water. The objective was to understand the impact of these wetlands on native amphibians. Frogs were exposed to wetlands containing oil sands process affected water (OSPW) and reference water (no OSPW). Six experimental trenches were made at one site in the first year. Each trench had 3 enclosures with 50 tadpoles. In the second year, there were 13 sites, including 6 reference and 7 OSPW affected sites, which were classified as old (more than 8 yrs) or young (less than 7 yrs). Four enclosures, with 50 tadpoles each, were placed in each wetland. The study involved the evaluation of growth rate, survival, time to metamorphosis, thyroid hormone concentrations, liver EROD activity, and tissue retinol concentrations. In addition, stable isotopes were used to track carbon flow from primary production plants, through the food chain, to tadpoles and frogs which represent intermediate and higher trophic levels in reclaimed wetlands.

  8. Strategic marketing opportunities for Suncor OSG [Oil Sands Group

    International Nuclear Information System (INIS)

    Carrothers, S.

    1993-01-01

    Suncor's Oil Sands Group (OSG) is in a unique position to provide advantages to its customers, producing a light, sweet resid-free crude at a time when North American production of this valuable type of oil is in decline. While the per-barrel production cost of synthetic crude has been high historically, the OSG has recently committed to over US$300 million in capital investments which will reduce unit costs to conventional levels. Adding to this, the plant is located on a reserve that, even with existing technology, could feed the plant virtually indefinitely. Three aggressive strategic initiatives which will enhance the value of the products are being undertaken. The product slate diversification initiative involves significantly expanding the production slate to include premium products that are customized to meet customer needs. The product quality initiative will address product characteristics that are unattractive to some end users. The transportation initiative will ensure reliable and timely delivery of a wide variety of OSG products to an expanded customer base. 1 fig

  9. Canadian incentives for oil and gas exploration. [Applicability to USA

    Energy Technology Data Exchange (ETDEWEB)

    1980-04-01

    During the 1970s a number of different exploration and production incentive programs were put in place in Canada, in particular in the Province of Alberta, Canada's principal oil- and gas-producing province. The DOE/RA is evaluating Canadian incentives for oil and gas exploration, and this study is intended to provide information that will help guide DOE/RA in determining the applicability of Canadian incentive programs in US energy policy. The study describes and documents the fiscal structure in which the Canadian oil industry operates. The incentive features of pricing policy, taxation policy, and provincial royalty systems are discussed. A principal focus of the study is on one of the most important of Canada's specific incentive programs, the Alberta Exploratory Drilling Incentive Credit Program (EDICP). The study describes and evaluates the effect of the EDICP on increased oil and gas exploration activity. Similarly, the study also reviews and evaluates other specific incentive programs such as the Alberta Geophysical Incentive Program, Frontier Exploration Allowances, and various tar sand and heavy oil development incentives. Finally the study evaluates the applicability of Canadian incentives to US energy policy.

  10. Post-Secondary Learning Priorities of Workers in an Oil Sands Camp in Northern Alberta

    Science.gov (United States)

    Fahy, Patrick J.; Steel, Nancy

    2008-01-01

    This paper reports results to date of a three-year project by Athabasca University, intended to determine the education and training needs and interests of employees in a work camp in northern Alberta's oil sands. (Future reports will address results of efforts to provide programming suiting the needs identified, and the uptake, satisfaction,…

  11. North American natural gas outlook : does gas remain a fuel option for oil sands?

    International Nuclear Information System (INIS)

    George, R.R.

    2003-01-01

    This paper presents a North America natural gas outlook from Purvin and Gertz, an international energy consulting firm that has 30 years experience in providing strategic, commercial and technical advice to the petroleum industry. In particular, this presentation focuses on natural gas market fundamentals and how they may impact on oil sands development. It includes charts and graphs depicting NYMEX natural gas outlooks to July, 2009 and examines how supply will react to major changes in Canada's supply portfolio. It was noted that oil sands development is a driver for natural gas demand in Alberta. The existing regional gas pipeline infrastructure was presented and the market impact on upgrader options was discussed. The author suggests that if gas prices are too high, there are other fuel options for steam and power generation. These include bitumen, asphalt, coke, coal and nuclear. However, these options have additional costs, uncertainties and environmental issues. A key factor for success would be to have a clear understanding of the benefits and risks between these fuel options. 1 tab., 9 figs

  12. On the origin of calcite-cemented sandstones in the clearwater formation oil-sands, Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Colquhoun, I.M.

    1999-01-01

    This thesis examined the formation of calcite-cemented sandstones in the Clearwater Formation within the Cold Lake and southern Primrose areas of the Alberta oil sands. Three stages of diagenesis have been recognized, both in the calcite-cemented sandstones and reservoir sands. Diagenesis of the Clearwater Formation in the Cold Lake and southern Primrose areas ended once the reservoir filled with hydrocarbons, but in the Cold Lake area, diagenesis of water-saturated sands likely continued after hydrocarbon emplacement. The reservoir sands in the formation contain a diverse clay mineral assemblage. In general, 0.7 nm clays dominate the diagenetic clay mineralogy of the Clearwater sands. Reservoir sands that contain large amounts of detrital clays and early diagenetic, grain-coating chlorite/smectite have significantly reduced bitumen-saturation. The presence of detrital and diagenetic smectitic clays complicates the removal of bitumen from the Clearwater formation using cyclic steam stimulation techniques because they swell during steam stimulation and reduce porosity and permeability of reservoir sands. Reservoir sands that contain kaolinite, feldspar and calcite react to form smectitic clays, which swell upon cyclic steam stimulation and further reduce porosity and permeability of reservoir sands. However, in the Cold Lake and Primrose areas, the dominant clay mineral is berthierine, which is associated with high calcite, which help to preserve porosity, permeability and bitumen saturation. The porous nature of bitumen-saturated, calcite-cemented sandstones that are laterally extensive could possibly provide a preferential path for steam to initiate calcite dissolution and produce significant concentrations of dissolved carbon dioxide in injected fluids. It was noted that this may then precipitate as carbonate scale within the reservoir and could cause formation damage or affect production equipment. 207 refs., 9 tabs., 58 figs., 3 appendices.

  13. Sulfate reducing bacteria and their activities in oil sands process-affected water biofilm

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hong; Yu, Tong, E-mail: tong.yu@ualberta.ca; Liu, Yang, E-mail: yang.liu@ualberta.ca

    2015-12-01

    Biofilm reactors were constructed to grow stratified multispecies biofilm in oil sands process-affected water (OSPW) supplemented with growth medium. The development of sulfate reducing bacteria (SRB) within the biofilm and the biofilm treatment of OSPW were evaluated. The community structure and potential activity of SRB in the biofilm were investigated with H{sub 2}S microsensor measurements, dsrB gene-based denaturing gradient gel electrophoresis (DGGE), and the real time quantitative polymerase chain reaction (qPCR). Multispecies biofilm with a thickness of 1000 μm was successfully developed on engineered biocarriers. H{sub 2}S production was observed in the deeper anoxic zone of the biofilm from around 750 μm to 1000 μm below the bulk water-biofilm interface, revealing sulfate reduction in the deeper zone of the stratified biofilm. The biofilm removed chemical oxygen demand (COD), sulfate, and nitrogen. The study expands current knowledge of biofilm treatment of OSPW and the function of anaerobic SRB in OSPW biofilm, and thus provides information for future bioreactor development in the reclamation of OSPW. - Graphical abstract: The development of sulfate reducing bacteria (SRB) within Oil Sands Process-affected Water (OSPW) biofilm and the biofilm treatment of OSPW were evaluated by Liu and coworkers. Combined microsensor and molecular biology techniques were utilized in this study. Their results demonstrated that multispecies biofilm with a thickness of 1000 μm was successfully developed on engineered biocarriers. H{sub 2}S production was observed in the deeper anoxic zone of the biofilm from around 750 μm to 1000 μm below the bulk water-biofilm interface, revealing sulfate reduction in the deeper zone of the biofilm. The biofilm removed chemical oxygen demand (COD), sulfate, and nitrogen. - Highlights: • Biofilm in oil sands wastewater was developed on engineered biocarriers. • Bacterial community and in situ activity of SRB were studied in the

  14. Sulfate reducing bacteria and their activities in oil sands process-affected water biofilm

    International Nuclear Information System (INIS)

    Liu, Hong; Yu, Tong; Liu, Yang

    2015-01-01

    Biofilm reactors were constructed to grow stratified multispecies biofilm in oil sands process-affected water (OSPW) supplemented with growth medium. The development of sulfate reducing bacteria (SRB) within the biofilm and the biofilm treatment of OSPW were evaluated. The community structure and potential activity of SRB in the biofilm were investigated with H 2 S microsensor measurements, dsrB gene-based denaturing gradient gel electrophoresis (DGGE), and the real time quantitative polymerase chain reaction (qPCR). Multispecies biofilm with a thickness of 1000 μm was successfully developed on engineered biocarriers. H 2 S production was observed in the deeper anoxic zone of the biofilm from around 750 μm to 1000 μm below the bulk water-biofilm interface, revealing sulfate reduction in the deeper zone of the stratified biofilm. The biofilm removed chemical oxygen demand (COD), sulfate, and nitrogen. The study expands current knowledge of biofilm treatment of OSPW and the function of anaerobic SRB in OSPW biofilm, and thus provides information for future bioreactor development in the reclamation of OSPW. - Graphical abstract: The development of sulfate reducing bacteria (SRB) within Oil Sands Process-affected Water (OSPW) biofilm and the biofilm treatment of OSPW were evaluated by Liu and coworkers. Combined microsensor and molecular biology techniques were utilized in this study. Their results demonstrated that multispecies biofilm with a thickness of 1000 μm was successfully developed on engineered biocarriers. H 2 S production was observed in the deeper anoxic zone of the biofilm from around 750 μm to 1000 μm below the bulk water-biofilm interface, revealing sulfate reduction in the deeper zone of the biofilm. The biofilm removed chemical oxygen demand (COD), sulfate, and nitrogen. - Highlights: • Biofilm in oil sands wastewater was developed on engineered biocarriers. • Bacterial community and in situ activity of SRB were studied in the biofilm.

  15. Pacific Northwest Laboratory Annual Report for 1979 to the DOE Assistant Secretary for Environment Part 4 Physical Sciences

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, J. M.

    1980-02-01

    This volume contains 63 articles on physical science activities in diverse areas, including coal, fission, radiation physics, geothermal resource development, oil shale and tar sand research, and multitechnology development.

  16. A First Assessment of the Elemental Composition of Atmospheric Aerosols in the Canadian Oil Sands Region

    Directory of Open Access Journals (Sweden)

    Dabek-Zlotorzynska E.

    2013-04-01

    Full Text Available Canadian Oil Sands, which comprise 97% of Canada’s 176 billion barrels of proven oil reserves, are located beneath 140,200 km2 of boreal forests, prairies and wetlands, and are the second largest known deposit of crude oil in the world. As such, this region has experienced rapid industrial development, which resulted also in increasing industrial air emissions, primarily from bitumen upgrading and mine vehicle fleet operations. This rapid development has led to concerns regarding health risk to humans, and other terrestrial and aquatic wildlife associated with exposure to toxic contaminants, especially metals and polycyclic aromatic compounds (PACs particularly along the Athabasca River and its watershed. Canada’s Minister of the Environment announced that Environment Canada (EC will jointly lead, in collaboration with Government of Alberta and relevant stakeholders, the development and implementation of an enhanced monitoring system in the Oil Sands region to provide information on the state of the air, water, land andbiodiversity. This work presents preliminary data on the first assessment of elemental composition of fine particulate matter (particles<2.5 mm in diameter; PM2.5 at 3 air quality sites in close proximity to Oil Sands processing activities. Since December 2010, integrated 24 hour air samples were collected every sixth day on a 47-mm Teflon filters using Thermo Fisher Partisol 2000-FRM samplers operated by the National Air Pollution Surveillance (NAPS network that involves EC and the Canadian provinces and territories. All samples including laboratory, travel and field blanks were subjected to gravimetric determination of PM2.5 mass and energy dispersive X-ray fluorescence (ED-XRF analysis for 46 elements. Since ED-XRF is a non-destructive technique, PM2.5 samples were subsequently analyzed for 37 trace elements including rare earth elements using inductively-coupled plasma mass spectrometry (ICP-MS combined with microwave

  17. Concentrations of the genotoxic metals, chromium and nickel, in whales, tar balls, oil slicks, and released oil from the gulf of Mexico in the immediate aftermath of the deepwater horizon oil crisis: is genotoxic metal exposure part of the deepwater horizon legacy?

    Science.gov (United States)

    Wise, John Pierce; Wise, James T F; Wise, Catherine F; Wise, Sandra S; Gianios, Christy; Xie, Hong; Thompson, W Douglas; Perkins, Christopher; Falank, Carolyne; Wise, John Pierce

    2014-01-01

    Concern regarding the Deepwater Horizon oil crisis has largely focused on oil and dispersants while the threat of genotoxic metals in the oil has gone largely overlooked. Genotoxic metals, such as chromium and nickel, damage DNA and bioaccumulate in organisms, resulting in persistent exposures. We found chromium and nickel concentrations ranged from 0.24 to 8.46 ppm in crude oil from the riser, oil from slicks on surface waters and tar balls from Gulf of Mexico beaches. We found nickel concentrations ranged from 1.7 to 94.6 ppm wet weight with a mean of 15.9 ± 3.5 ppm and chromium concentrations ranged from 2.0 to 73.6 ppm wet weight with a mean of 12.8 ± 2.6 ppm in tissue collected from Gulf of Mexico whales in the wake of the crisis. Mean tissue concentrations were significantly higher than those found in whales collected around the world prior to the spill. Given the capacity of these metals to damage DNA, their presence in the oil, and their elevated concentrations in whales, we suggest that metal exposure is an important understudied concern for the Deepwater Horizon oil disaster.

  18. Method for creating high carbon content products from biomass oil

    Science.gov (United States)

    Parker, Reginald; Seames, Wayne

    2012-12-18

    In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

  19. Initial geochemical characteristics of fluid fine tailings in an oil sands end pit lake

    Energy Technology Data Exchange (ETDEWEB)

    Dompierre, Kathryn A. [Department of Civil and Geological Engineering, University of Saskatchewan, Saskatoon, Saskatchewan, Canada S7N 5A9 (Canada); Lindsay, Matthew B.J., E-mail: matt.lindsay@usask.ca [Department of Geological Sciences, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E2 (Canada); Cruz-Hernández, Pablo [Department of Geology, University of Huelva, Campus ‘El Carmen’, E-21071 Huelva (Spain); Halferdahl, Geoffrey M. [Environmental Research and Development, Syncrude Canada Limited, Edmonton, Alberta T6N 1H4 (Canada)

    2016-06-15

    Geochemical characteristics of fluid fine tailings (FFT) were examined in Base Mine Lake (BML), which is the first full-scale demonstration oil sands end pit lake (EPL) in northern Alberta, Canada. Approximately 186 Mm{sup 3} of FFT was deposited between 1994 and 2012, before BML was established on December 31, 2012. Bulk FFT samples (n = 588) were collected in July and August 2013 at various depths at 15 sampling sites. Temperature, solid content, electrical conductivity (EC), pH, Eh and alkalinity were measured for all samples. Detailed geochemical analyses were performed on a subset of samples (n = 284). Pore-water pH decreased with depth by approximately 0.5 within the upper 10 m of the FFT. Major pore-water constituents included Na (880 ± 96 mg L{sup −1}) and Cl (560 ± 95 mg L{sup −1}); Ca (19 ± 4.1 mg L{sup −1}), Mg (11 ± 2.0 mg L{sup −1}), K (16 ± 2.3 mg L{sup −1}) and NH{sub 3} (9.9 ± 4.7 mg L{sup −1}) were consistently observed. Iron and Mn concentrations were low within FFT pore water, whereas SO{sub 4} concentrations decreased sharply across the FFT–water interface. Geochemical modeling indicated that FeS{sub (s)} precipitation was favoured under SO{sub 4}-reducing conditions. Pore water was also under-saturated with respect to gypsum [CaSO{sub 4}·2H{sub 2}O], and near saturation with respect to calcite [CaCO{sub 3}], dolomite [CaMg(CO{sub 3}){sub 2}] and siderite [FeCO{sub 3}]. X-ray diffraction (XRD) suggested that carbonate-mineral dissolution largely depleted calcite and dolomite. X-ray absorption near edge structure (XANES) spectroscopy revealed the presence of FeS{sub (s)}, pyrite [FeS{sub 2}], and siderite. Carbonate-mineral dissolution and secondary mineral precipitation have likely contributed to FFT dewatering and settlement. However, the long-term importance of these processes within EPLs remains unknown. These results provide a reference for assessing the long-term geochemical evolution of oil sands EPLs, and offer

  20. The last oil century? The truth about world reserves - a geologist's viewpoint; Le dernier siecle du petrole? La verite sur les reserves mondiales - le point de vue d'un geologue

    Energy Technology Data Exchange (ETDEWEB)

    Mathieu, Yves

    2010-11-01

    Will the 21. century be the on of world oil reserves exhaustion? This fear of an oil-less world is shared by all: politicians, oil company heads, scientific experts, economists and, above all, by consumers. The author, a geologist and renowned expert of the domain, answers this vital question and presents the real situation of oil reserves country by country. He also evaluates the potentialities offered by non-conventional oils (heavy crudes, tar sands and oil shales) as well as by this desertic and hostile area considered as the new energy eldorado: the Arctic. This specialist's book, accessible to everyone, approaches in a didactic way the different economical and political stakes linked with world oil reserves. This analysis raises the issue: how long could we count on oil at accessible cost to cover our energy needs? (J.S.)

  1. Characterization of methane emissions from five cold heavy oil production with sands (CHOPS) facilities.

    Science.gov (United States)

    Roscioli, Joseph R; Herndon, Scott C; Yacovitch, Tara I; Knighton, W Berk; Zavala-Araiza, Daniel; Johnson, Matthew R; Tyner, David R

    2018-03-07

    Cold heavy oil production with sands (CHOPS) is a common oil extraction method in the Canadian provinces of Alberta and Saskatchewan that can result in significant methane emissions due to annular venting. Little is known about the magnitude of these emissions, nor their contributions to the regional methane budget. Here the authors present the results of field measurements of methane emissions from CHOPS wells and compare them with self-reported venting rates. The tracer ratio method was used not only to analyze total site emissions but at one site it was also used to locate primary emission sources and quantify their contributions to the facility-wide emission rate, revealing the annular vent to be a dominant source. Emissions measured from five different CHOPS sites in Alberta showed large discrepancies between the measured and reported rates, with emissions being mainly underreported. These methane emission rates are placed in the context of current reporting procedures and the role that gas-oil ratio (GOR) measurements play in vented volume estimates. In addition to methane, emissions of higher hydrocarbons were also measured; a chemical "fingerprint" associated with CHOPS wells in this region reveals very low emission ratios of ethane, propane, and aromatics versus methane. The results of this study may inform future studies of CHOPS sites and aid in developing policy to mitigate regional methane emissions. Methane measurements from cold heavy oil production with sand (CHOPS) sites identify annular venting to be a potentially major source of emissions at these facilities. The measured emission rates are generally larger than reported by operators, with uncertainty in the gas-oil ratio (GOR) possibly playing a large role in this discrepancy. These results have potential policy implications for reducing methane emissions in Alberta in order to achieve the Canadian government's goal of reducing methane emissions by 40-45% below 2012 lev