Survey of the actual energy consumption in the commercial/residential sector; Minsei bumon energy shohi jittai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A questionnaire survey was conducted of the actual energy consumption in the business sector (schools, hotels/inns, hospitals, and other service business) in fiscal 1996, and was put together with the survey conducted in the past in order to clarify the structure and trend of energy consumption in the commercial/residential sector. The survey was aimed at making basic data for the development/introduction of the petroleum substituting energy including future new energy. The consumption unit requirement of a school total was 84.9 Mcal/m{sup 2} per year, that of a hotel/inn total was 455.3 Mcal/m{sup 2} per year, and that of a hospital total was 400.2 Mcal/m{sup 2} per year. The energy consumption for business use was summarized. The consumption unit requirement of restaurants was the largest, 622.8 Mcal/m{sup 2} per year, and that of schools was the smallest. In office building business and wholesale/retailing business, electricity is largely used mostly for illumination, power, etc. In restaurants, gas is largely used mostly for its own use including cooking. In schools, energy use for space heating was the largest, but was almost the same as that in office buildings in terms of the amount. 179 figs., 31 tabs.

Long-distance power transmission technology. Microwave power transmission; Denryoku no chokyori yuso gijutsu. Micro ha musen soden

Energy Technology Data Exchange (ETDEWEB)

Kaya, N [Kobe University, Kobe (Japan). Faculty of Engineering

1994-11-05

This paper explains the principles of microwave power transmission as a long-distance power transmission technology, and the status of its development. Under an assumption of using a wave length of 12 cm (2.45 GHz) and a transmission distance of 1 km, an ideal wireless power transmission can realize transmitting the power at an efficiency of 95% or higher if transmitting and receiving antennas with a radius of 8.8 m are used. What remains as important requirements is raising the efficiency of conversion from power supply into microwaves, and the efficiency of rectification after the power has been received. By using microwave energy sent from a transmission antenna installed on the roof of an automobile, a model airplane with a receiving antenna installed at its rear flew successfully for 40 seconds under the microwave lifted airplane experiment (MILAX). In an experiment of transmitting microwave power in space, power was successfully transmitted to the child rocket as an event under the International Space Year - Microwave Energy Transmission in Space (ISY-METS). The microwave wireless power transmission on the ground would have a possibility of taking over the overhead line transmission into islands. An attempt is scheduled to send power of 5 kW by using transmission and receiving antennas with a diameter of 3 m to investigate effects on transmission efficiency, and communications and electromagnetic environments, and to collect basic data. 3 refs., 3 figs.

Cut down the peak daytime demand for electricity at the residence; Jutaku ni okeru denryoku fuka heijunka

Energy Technology Data Exchange (ETDEWEB)

Ishihara, O. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

1996-09-05

For leveling of power load in small-scale buildings and houses, a test house with actual size was constructed in order to examine soil heat storage system using photovoltaic power generation system and nighttime power. A hundred of polycrystal silicone solar cells with about 5 kW and twenty of amorphous ones were fixed on the roof, to connect with commercial power source by the system interconnection having inverse power flow. For leveling of power load in the periods of heating and cooling, soil heat storage system was applied using nighttime power. Pipes for circulating cooling and heating water were embedded. Heat pump was operated only in the time zone of nighttime power, to obtain cooling and heating source for fan coil unit in the daytime. The sold power was larger than purchased power under continuous cooling condition for twelve hours in summer. Since cooling load was supplied from nighttime power with lower price, there was a large peak cut effect in the daytime. As a result of the tests using a house with actual size, the system was found to be applied practically both in summer and in winter. Effectiveness of peak cut of power load in summer was also provided. 7 refs., 10 figs., 2 tabs.

Approach to load leveling in Kansai Electric Power Co. Inc.; Kansai Denryoku no fuka heijunka eno torikumi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

This paper presents an electric hot-water heater and ice storage air conditioning system as systems to be recommended for load leveling. Electric hot-water heater is featured by safety, cleanliness, silence and convenience because of no use of fire. Its electricity charge is only 7.15 yen/kWh less than 1/3 of that for ordinary homes because of use of midnight power. Mainly used MPU-control type electric hot-water heater is more economical because of a 15% discount system. Ice storage air conditioning system is operated in the daytime using ice made by midnight power. It is featured by reduction of facility and installation costs due to the small capacity of heat source equipment, use of inexpensive midnight power, and reduction of running cost due to small contract demand. However, since an ice storage air conditioning system is in the initial stage of diffusion, its initial cost is expensive as compared with conventional non-heat storage air conditioning systems, remaining the issue of cost reduction. 3 figs., 1 tab.

Investigation of load leveling in Hokuriku Electric Power Co., Inc.; Hokuriku denryoku no fuka heijunka eno torikumi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

Hokuriku Electric Power Co., Inc. aims at an around 2% improvement of the load factor up to 2005, by which the quick and proper service and the proposal of load leveling menu are planned. This paper describes an outline of the investigation of load leveling. Various programs have been proposed so that the customers can further shift the load by their consideration. Proposed systems include the time-of-day electricity rate system, the load regulation contract system for industries, the seasonal time-of-day rate system, the electric power system for snowmelt in which the load is dumped at the peak, and the secondary electric power system for snowmelt. Accompanying with the revision of electric utility law, the enlargement of its available time, the price reduction, and the discount rate system for the ice regenerative air conditioners have been provided. For the business activities, a demonstration model house was exhibited to indicate a proper house with local characteristics in Hokuriku district. Furthermore, the spreading activities of regenerative systems and the consulting activities have been positively promoted. 4 figs., 1 tab.

Survey of the actual state of energy consumption in the residential/commercial sector; Minsei bumon energy shohi jittai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to energy demand in the business field, the paper conducted a questionnaire survey of the actual state and preparation of the existing literature and data. The purpose is to make the consumption structure and trend clear and to make it useful for the development/introduction of new energy and petroleum substitution energy in the future. The unit energy consumption in the business type, `office buildings` decreased from 227.0 Mcal/m{sup 2} per year in the fiscal 1990 survey to 179.5 Mcal/m{sup 2} per year in the fiscal 1995 survey. The energy type shifted from petroleum to electricity and gas. The unit energy consumption in the business type, `wholesale/retail` slightly decreased from 360.9 Mcal/m{sup 2} per year in the previous survey to 342.7 Mcal/{sup 2} per year in the survey this time. The energy type showed the same trend as in the case of office buildings. The unit energy consumption in the business type, `restaurants` increased from 573.3 Mcal/m{sup 2} per year in the previous survey to 622.8 Mcal/m{sup 2} per year in the survey this time. As energy type, electricity increased while gas remarkably decreased. 55 refs., 155 figs., 29 tabs.

Fundamental characteristics of new electric power storage equipment celled `ECS`; Atarashii denryoku chozo sochi `ECS` no kisoteki tokusei

Energy Technology Data Exchange (ETDEWEB)

Okamura, T.; Yamagishi, M.

1997-01-30

This paper introduces new electric power storage equipment called an energy capacitor system. A special electrically double-layered capacitor with its energy density raised in sacrifice of internal resistance has the current so adjusted that loss will not increase by using a switching converter (consisting of a charger and a current pump). The capacitor is charged and discharged at high efficiency. Upper limits of the charge voltage for each capacitor are connected with parallel monitor circuits so that maximum charge voltage of each capacitor will be aligned at one level, wherein charge and discharge are performed with that voltage used as the starting point. A drawback in a capacitor is lower energy density than in a secondary battery. Therefore, high voltage withstanding organic electrolyte was used, and electrode activated carbon was given discussions starting from its raw material structures. The efforts resulted in obtaining as high energy density as 43 Wh/kg (about 20 times as much as in conventional materials, and comparable to lead-acid batteries). In order to minimize heat generation due to the increased internal resistance, a switching converter was used to suppress charge/discharge currents to the minimum required levels. Although the capacitor still has insufficient voltage withstanding power and short life, the energy density is increasing beyond the initial estimation. The next problem to be solved is reduction in production cost for its industrialization. 4 refs., 4 figs., 2 tabs.

Research report for fiscal 1998 on the basic research for energy consumption efficiency improvement in developing countries. Joint research for oil consumption efficiency improvement. Indonesia; 1998 nendo hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa jigyochosa hokokusho. Indonesia

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

On-site researches are conducted to study the possibility of a model business using energy-saving and environment preservation technologies of Japan and Indonesia. At textile plants, the management of heat and water in the dyeing and finishing processes is found inadequate, with great quantities of heat left uncared-for in medium- and low-temperature wastewater. An energy-saving proposition is submitted in which solar energy and absorption-type refrigerators are combined. Instrumentation and management also require improvement. At nitrogenous and phosphatic fertilizer plants, the energy consumption rate is found aggravated by degradation of facilities, and continued research and further analysis are necessary before working out energy-saving policies for them. At urea fertilizer plants, though it is not easy to modernize the manufacturing processes, energy-saving and environment preserving efforts are under way within the bounds of capability. Their energy consumption rate is high because of frequent shut-downs. It is necessary to detect an anomaly at its early stage and to introduce backup systems for the elimination of erroneous operations. Operating conditions need to be analyzed for validity. At melamine manufacturing plants, process drainage is allowed into the river without any treatment contaminating the water with products of melamine hydrolysis. Short-term and long-term solutions are suggested. (NEDO)

Basic research on energy conservation in developing countries. Joint research on oil conservation (research report on the industrial basis of Socialist Republic of Vietnam); Hatten tojokoku energy shohi koritsuka kiso chosanado jigyo sekiyu shohi koritsuka kyoryoku chosa. Betonamu shakai shugi kyowakoku sangyo kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The field research of oil conservation was conducted in developing countries, in particular, Vietnam where a steep increase in oil consumption is anticipated in the future. Energy conservation is the most effective direct measures to control combustion of fossil fuels, and an important issue to be promoted by all countries in the world to prevent global warming and reserve energy resources. In fiscal 1994, main industries in the northern part of Vietnam were researched. In fiscal 1995, the report meeting of plant survey results in the northern part and the technical seminar of energy-saving in industrial field were held, and plants around Ho Chi Minh City in the southern part of Vietnam were researched. Although Vietnam has recently acquired membership in ASEAN and is undergoing dramatic economic growth, has many problems in environmental measures. Japan has top-ranking results on energy-saving in industrial field, and the transfer of such superior technologies and techniques will greatly contribute to resource and global warming problems as well as pollution control measures in Vietnam. 13 refs., 25 figs., 26 tabs.

Fiscal 2000 survey report. Development of novel battery power storage system (Development of distributed power storage technology - Marketability of lithium storage battery); 2000 nendo gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu - Bunsangata denryoku chozo gijutsu kaihatu (Ritium niji denchi no shijosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A survey is conducted of the current status of storage batteries and the marketability of the lithium ion battery. In the study of future marketability of storage batteries for electric vehicles, the small vehicle Hypermini currently loaded with a lithium ion battery is taken up and it is assumed that each carries a 10 kWh battery, and then it is estimated that there will be an approximately 2200 times 10{sup 3} kWh market in Japan in 2020. As for hybrid vehicles each loaded with a 1 kWh battery, it is estimated that 3997 times 10{sup 3} kWh will be on the market in 2020. For the fuel cell powered vehicle, similarly, there will be approximately 2,500 times 10{sup 3} kWh on the market in 2020. As for power storage facilities for power load shaving, the demand for cells in 2020 is estimated at 1,032-3,924 times 10{sup 3} kWh on the assumption that they operate 4 hours in the daytime. As for the uninterruptible power supply, it is estimated that 800 times 10{sup 3} kWh will be required by those installed at data centers in 2020. It is also estimated that 252 times 10{sup 3} kWh will be necessary in the form of storage batteries for motored wheelchairs in 2020. As for distributed power source systems such as those dealing with wind power or photovoltaic power, there are a number of technical problems that have to be settled. (NEDO)

Load leveling efforts of The Hokkaido Electric Power Co. Inc.; Hokkaido Denryoku no fuka heijunka eno torikumi ni tsuite

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The Hokkaido Electric Power Co., Inc., aiming to enhance power generation efficiency through power load levelling, strives to expand and substantiate its electricity billing menu and to popularize and encourage the use of levelling-oriented apparatuses and systems most of which are designed for utilizing midnight power. The billing menu has in it a snow-melting power which is cut off for load levelling during the peak demand time zone. For domestic use, a time zone-specified lighting system named Dream Eight is created, which is one of the billing systems dependent upon time zone. Introduced therein for industrial use is a demand/supply adjustment contract system. Furthermore, in compliance with the amended Electricity Business Law that came into force in 1995, efforts are under way for revising the period wherein power is to be supplied for melting snow, expanding the scope of application of the power supply system dependent upon time zone, and newly introducing a heat accumulation assisted peak adjustment contract system and an operation adjustment contract system. As for business efforts in relation to load levelling, the company proposes household electrical systems centering about 200V high-efficiency apparatuses, electric water warmer contributing to the enhancement of year-round load levelling, popularization and reinforcement of electric snow melting systems, and power utilizing technologies capable of meeting local demands raised for example by agriculture and fishery.

Efforts of load leveling in Tohoku Electric Power Co. Inc.; Tohoku denryoku no fuka heijunka eno torikumi ni tsuite

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-01

This paper describes efforts of load leveling in Tohoku Electric Power Co., Inc. from the viewpoint of the rate system and business development. For the approach from the rate system, various rate menus for the peak shift have been arranged for domestic and large industry customers. To create the midnight demand, spread and expansion of electric hot water service are promoted. Consequently, the contract of midnight power has reached 914,000 kW at the end of 1995, which was 774,000 kW in 1985. To spread the ice regenerative air conditioning systems, the grant of incentive to the manufacturers and special discount of electricity rate have been conducted. These systems have been introduced in the eight places of Tohoku Electric Power`s business. The spread incident system has been created to introduce the automatic vending machines for beverages with the power peak cut function. Unused energy, such as exhaust heat from the non-treated sewage water and substations has been utilized as a heat supply project for city redevelopment. Multi-functional heat pump with regenerative function has been developed. This system aims at the peak shift by combining multi-functional heat pump and electric hot water service. 2 figs., 2 tabs.

Basic survey project of advanced efficiency of energy consumption in developing countries. Cooperation survey of efficient consumption of petroleum (survey of industrial foundation in the Philippines); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa. Philippine koku sangyo kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of the survey is to promote the international research cooperation projects from the survey stage, via demonstration research stage to the diffusion stage. Field surveys have been conducted to find out the needs of energy saving and environmental technology for the efficient consumption of petroleum in the developing countries with mass-consumption of petroleum in the future. The survey was conducted in the Philippines in the FY 1996. Next developing themes were proposed. The first theme was developing method of sugar plant. The magnesia method has been developed as a basic technology for cleaning sugar solution process instead of using lime. By the recycling method, the waste cake amount can be remarkably reduced. The second theme was electron beam exhaust gas treatment by a dry method of simultaneous desulfurization and denitrification of high concentration SOx and NOx in the fertilizer production plants. The third theme was the energy saving technology for SOx reduction of heating furnace for iron-steel by using an ultra energy saving-type regenerative burner. The last theme was chlorine bypass technology in cement industry, which would become an advanced technology development for the use of chlorine containing fuels in the near future. 40 refs., 36 figs., 79 tabs.

Concrete for the construction of No. 1 nuclear power generator of Tokyo Denryoku Co.'s Kashiwazaki, Kariha nuclear power station

International Nuclear Information System (INIS)

Suzuki, Yasuyoshi; Eguchi, Kiyoshi; Nakakomi, Akira.

1985-01-01

The construction of the No.1 power generator of Kariha nuclear power generator was completed on March 1985, and the installations of equipments are on their way aiming the start in October 1960. About 900,000 m 3 of concrete was produced and used for whole work and about 500,000 m 3 out of total was used for the construction of plant building. For constructing reactor building and turbin building, the concrete must have shielding property against radiation. The specific gravity no less than 2.5 was required for dry state of laid concrete. In order to supply very large amount of concrete with stable quality, preliminary investigation on raw materials including aggregates, fly-ash and surface active agents, were made. Aggregates were stored in underground bins to keep the temperature constant for the purpose of obtaining mixed concrete with constant temperature. For determining the mixing rate of concrete, physical test such as slump test, determination of air content, determinations of strengths and specific gravities of solidified concrete. Quality control committee was established to observe the optimum condition, which were confirmed by preliminary tests, of concrete preparation. As the results of detailed preliminary investigation on respective raw material and strict quality control from the source of raw material to mixed concrete, the supply of concrete with stable quality which conforms every requirement of standard, was possible. (Ishimitsu, A.)

Load levelling measures being tackled by shikoku Electric Power Co. Inc.; Shikoku Denryoku Kabushi Kaisha no fuka heijunka eno torikumi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

For the electric power companies, the activity of pushing forward the load levelling contributes greatly to the curtailment of cost by means of effective formation and utilization of facilities. It is planned to take up more positive activities with a target of 3% improvement in the load factor in ten years. Concrete measures for further promotion of load levelling are the diversity of the rate menu of appraising the load levelling effort of the customers and the promotion of the spread of equipment and systems relating to load levelling such as electric water heating apparatuses and thermal energy storage air conditioning systems. The rate system has been reviewed taking the opportunity of rate revision made in January, 1996. Particularly, further load shift to midnight time zone is expected as a result of better rate incentive for customers which is brought about by large reduction of the rate level due to the cost reduction effect accompanying the improvement in atomic power generation ratio. Outlines are given on the fields relating to general households, business, dwellings, buildings, and industry. 3 figs., 1 tab.

Approach undertaken by our Company for leveling electric loads; Chubu Denryoku Kabushi Kaisha no fuka heijunka eno torikumi ni tsuite

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

Measures for leveling the electric loads relying upon two facets - tariff system and business activities - in Chubu Electric Power Co., Inc. are presented. Firstly, the existing pricing systems for midnight electric power and electric light according to the period of time for the household as well as those of seasonal and time zone electric power, modifiable contract with the time zone and so forth for large industry users, together with a similar contract for the owner of regenerating installation are outlined. In addition, a price reduction system is indicated in favor of a scheduled shutdown of large industry operations as a means of avoiding electric consumption during weekdays in summer and between 13h and 16h when large demands exist. Further, a selective contract system put in service in 1995 and the price reduction for ice regenerating air conditioning system are cited. As for business facet, 1995 is regarded as the first year of the ice regenerator for its generalization through exhibition and promotive campaign to the foods processing industry, and the application of the latent heat regenerative system to perishable foods is recommended. Moreover, installation of energy saving type automatic vending machine, so-called eco-vendor is encouraged for its merit of peak-cut and energy price lowering. Lastly, activities to extend the use of electric calorifiers and the regenerative floor heating are mentioned. 2 figs., 1 tab.

Fiscal 1999 achievement report. Development of ultralow-loss power device technology; 1999 nendo choteisonshitsu denryoku soshi gijutsu kaihtsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The aim is to establish basic technologies for upgrading wide-gap semiconductor devices, fabricated mainly of SiC, in terms of their low-loss, high-speed, and high-power features. In the research and development of ultralow-loss power device technology, progress of the effort is reviewed, problems in the process of research and development are extracted, and technological trends are surveyed. In the development of basic technologies, an SiC crystal growing device is experimentally built and the process of crystal growth is assessed and analyzed, and tasks to discharge for higher quality and larger diameter are extracted. Basic technologies are developed relative to the epitaxial growth, interface control, and conductivity control of SiC etc. In the development of technologies for developing SiC into devices, technological development is carried out for the junction-type FET (field effect transistor), which involves termination structure optimization, high-voltage capability enhancement, and gate-off gain improvement. As for MOSFET (metal oxide semiconductor FET), MOS channel formation technology is developed and device-constructing technology is also developed. As for MESFET (metal-semiconductor FET), micro-processing is established for a success in experimentally building a 0.5{mu}m-long gate. (NEDO)

Research report of fiscal 1997. Basic research project on energy saving in developing countries (cooperative research on oil saving / basic research on the industry of Thailand); 1997 nendo chosa hokokusho. Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa (Taikoku sangyo kiso chosa hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Field research was made for oil saving in Thailand. To promote energy saving in a textile industry as main export industry, its motivation for production stuff is essential in business improvement. Proposal for work improvement, supply system of bonuses, and small-group activity are effective. Management of an energy consumption rate is essential in business management. Use of efficient waste water treatment equipment is also one of the issues. In food factories, various scopes for improvement are still found by mass/heat balance analysis in production process. As an example, a large amount of water is consumed in vain for washing raw rice in a rice powder factory, and separation of SS precipitate from waste water should be improved. Because of lagoon treatment, an effluent standard is not achieved in spite of consumption of wasteful aeration power. This treatment is reasonable because of its scale and site, although the standard can be achieved by activated sludge method. Reconsideration of the standard is also necessary based on a local total BOD load capacity. The profitability of a methane fermentation method should be examined. 72 figs., 95 tabs.

Fiscal 1999 survey report. Basic survey project on international cooperation for energy consumption efficiency improvement (Project on cooperation for oil consumption efficiency improvement - Fiscal 1999 survey report on Indonesia); Kokusai energy shohi koritsuka nado kyoryoku kiso chosa jigyo / sekiyu shohi koritsuka kyoryoku chosa jigyo. 1999 nendo Indonesia chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to contribute to the promotion of international research cooperation ranging from the survey stage through the stages of verification study and popularization, and, for this purpose, it conducts on-site investigations for exploring needs for environmentally-friendly energy-saving technologies in developing countries where there will be massive-scale oil consumption in the future. In this report, surveys and deliberations are conducted to embody proposed measures, and findings are compiled, based on the surveys conducted in the preceding financial year relating to energy efficiency in and environmental technologies for the textile and chemical industries. Much is expected from the proposed measures as promising subjects of joint verification researches. A technology is proposed for energy saving in the textile industry of Indonesia. The technology aims to wash cloth using high-pressure water from a special nozzle, to continuously measure the level of contamination of the waste water, and to feed back the measured values to the water supply side for the automatic optimization of the amount of the washing water and for the utilization of warm waste water for the ultimate purpose of cascade-aided energy saving. As for the proposition for recovering chemicals mainly caustic soda, it achieves environmental improvement and energy saving in the chemical industry simultaneously. (NEDO)

Fiscal 1998 research report. Survey on energy consumption in a residential sector; 1998 nendo chosa hokokusho. Minsei bumon energy shohi jittai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

On energy consumption in a residential sector, the report reports the document survey result including new documents, and the result of the systematic national questionnaire survey carried out in small and medium cities to prepare the basic data for future development and introduction of petroleum substituting energy. The electric power consumption rate of detached houses (A) is larger by 0.6- 1.6Gcal/household/year than that of apartment houses (B) in every district. The gas consumption rate of A is smaller than that of B in Hokkaido, Kanto and Kyushu. The LPG consumption rate of Kinki district is largest in both A and B. The kerosene consumption rate of A is larger than that of B. In Hokkaido, the kerosene consumption is extremely large in heating, showing a ratio of 60% or more in A. In the other districts, the kerosene consumption is largest in hot water supply, showing 30% or more. Every consumption rate increases with annual household income. The average consumption rate of 4 districts is 11,137Mcal/household/year. (NEDO)

Deregulation for the electric power industry in Japan and the outlook; Nippon no denryoku sangyo no kisei kanwa to sono tenbo

Energy Technology Data Exchange (ETDEWEB)

Matsuo, N. [The Institute of Energy Economics, Tokyo (Japan)

1996-10-01

The future direction and outlook of the electric power industry in Japan was described in a new systematical framework based on the amendment to the Electric Utility Industry Law. When viewing the deregulation system from a viewpoint of `induction of competition,` comparative assessment may mean competition introduced among electric power companies; establishment of the competitive bidding system by the whole supply business may mean competition introduced into the power generation sector; establishment of the specified electric utility industry system may mean competition introduced into the retailing sector. Further, a system to notify the authority of the price list, rationalization of safety rules, deregulation on the entry into another business, etc. can be interpreted as the spread of a width of discretion on business management. An increase in economic efficiency by cost reduction is expected as an influence of this deregulation, but the subject is how well the deregulation can balance with publicity and social responsibility. Relating to the entry of IPP, there is some anxiety: small scale power sources have high failure rates and difficulty in load frequency control. Moreover, it affects the public benefit in a sense of the apparently worsening air pollution. 12 figs., 1 tab.

Investigation on the actual energy consumption by office automation devices used in offices; Office ni okeru OA kiki no energy shohi jittai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

With an objective to further improve efficiency of power demand by office automation devices and suppress increase in the power demand, investigations were carried out on the actual power consumption by office automation devices, and discussions were given on energy saving effects in the office automation devices. In the investigations, measurements were conducted for small offices as the subject thereof with regard to electric power consumed by such presentation tools and their peripheral devices as personal computers, word processors, copying machines, facsimile machines, electronic whiteboards and overhead projectors. Power consumption particularly in a standby condition was also investigated. As a result of the investigations, the following characteristics were revealed: the number of office automation devices used to deal with the Energy Star is increasing rapidly; power consumption believed to have been reduced by the Energy Star transferring to lower power consumption is estimated to be 3% in average for personal computers, 26% for copying machines, and 68% for facsimile machines; and while facsimile machines are left in operating condition for 24 hours, their operation rate at night is very low, wherein there is a large room for saving energy in this time band. 65 figs., 21 tabs.

Fiscal 1999 survey report. Data collection, analysis, and investigation for energy efficiency improvement; 1999 nendo energy shohi koritsuka joho shushu bunseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With economy growing at a fast pace in the Asia-Pacific region in recent years, demand for energy is sharply increasing in various industries, and the demand is expected to continue to grow. It is afraid that the trend may extend to other developing regions such as East Europe. It is, and will remain to be, important to prevent warming, assure sustained economic development, and secure stable supply of energy on the global scale. The survey in this report aims to grasp the trends of energy efficiency improvement in Asia-Pacific nations, in other developing nations, and in developed nations as well, to ultimately serve the best interests of Japan. For the achievement of the goal, Japan's attitude toward energy conservation promotion activities is expressed at international conferences on energy conservation promotion such as those of APEC (Asia-Pacific Economic Cooperation Conference) in the Asia-Pacific region and of environmental/energy-saving conferences of IEA (International Energy Agency) in Europe and America. On these occasions, information is collected and overseas technical literature is obtained thanks to the established coordination with United Nations-affiliated organizations and key persons in various countries. Data and information thus acquired are utilized for the investigation and analysis of energy conservation technologies and policies adopted and diffused in the respective nations involved. Using them, promotion of energy conservation policies in the Asia-Pacific region and establishment of environmental friendliness are also investigated. (NEDO)

Fiscal 1998 research report on the global environmental assessment for efficient energy consumption; 1998 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

International Panel on Climate Change (IPCC) published the 1st assessment report in 1990 and the 2nd report in 1995 since its establishment in 1988, and is promoting the 3rd research and analysis. Among them, this report describes the study on technology transfer for efficient energy consumption. For stabilizing greenhouse effect gas concentrations in the air, strong control of such gas emission is indispensable, and a role of technology is important for the control. For overcoming some weak points for climate change, practical use of applicable technologies is necessary over a certain period of time, and technology transfer is essential in each country and all over the world. For promotion of such approach, the analysis and evaluation for technology transfer and diffusion are useful in addition to reports on technology itself. Based on such understanding, IPCC has promoted preparation of the special report on methodological and technological issues of technology transfer since 1997. Its approval at the IPCC general meeting is expected in late 1999 or early 2000. Some chapters related to efficient energy consumption are presented. (NEDO)

Unutilized energy utilizing systems. ; Power and levelling measures and unutilized energies. Miriyo energy katsuyo system. ; Denryoku fuka heijunka taisaku to miriyo energy

Energy Technology Data Exchange (ETDEWEB)

Kuromoto, E. (The Tokyo Electric Power Co. Inc., Tokyo (Japan))

1993-02-12

This paper explains quantitatively performance of heat storage tanks contributing largely to levelling power loads, and promoting and spreading more effective use of unutilized energies. A model case was used to compare differences in effectiveness of unutilized energy utilization with and without use of heat storage tanks. The heat demand used was a value in a day with a peak room cooling demand, and a heat supply system using water heat source heat pumps that utilize sewage treated water was used to manufacture cold water. As a result, the effective utilization rate of unutilized energy was increased to about 1.3 times when heat storage tanks were used. Effectiveness of a heat storage tank comes from its capability that excess amount of cold water manufactured during nighttime when heat demand falls by utilizing sewage treated water is stored in the heat storage tank, and the stored cold water can be supplied being mixed with cold water manufactured during daytime when heat demand rises sharply in daytime. Because sewage treated water has its annual temperature difference stabilized at about 10[degree]C, a heat pump utilizing the sewage treated water can reduce power required to produce heat of 1 Gcal by about 40% during room heating and about 15% during room cooling over the heating tower type heat pump. 8 figs., 1 tab.

Economic evaluation on participation of IPP as seen from an electric power system; Denryoku system kara mita IPP sannyu no keizaiteki hyoka

Energy Technology Data Exchange (ETDEWEB)

Kato, F.; Horibe, H.; Hayakawa, M.; Suzuki, Y.; Kaji, Y. [Nagoya University, Nagoya (Japan)

1997-01-30

A discussion was given on value of participation of an IPP as seen from an electric power system operation plan prepared by utilities. In the discussion, evaluation was made using as the breakeven cost of IPP power purchase prices the difference in power generation cost between electric power systems in which an IPP is participating and not participating, or in other words, the reduced portion of the power generation cost. As a result of the discussion, the following matters were indicated: in the case where an utility company expands its capacity by installing a coal-fired thermal power plant which is lower in operation cost, to deal with increase in power demand, the breakeven cost could be an avoidable cost for the utility company; if the expansion by installing a coal-fired thermal plant is not possible, the breakeven cost for a base type IPP would rise; the breakeven cost for a peak type IPP would be higher than for the base type IPP because the breakeven cost can serve to cut the peak for generators owned by the utility company; and participation of an IPP to power sources in remote areas would provide a large effect to reduce power transmission loss in an entire system, thereby increasing the breakeven cost. 1 ref., 9 figs., 3 tabs.

Fiscal 1999 survey report. Survey of effect of energy efficiency improvement on global environment; 1999 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Analyses are conducted into consideration given to global warming measures in the 3rd assessment report of the Intergovernmental Panel on Climate Change (IPCC) and into technology transfer from developed nations to developing nations in the Asia-Pacific region etc. to contribute to their energy efficiency improvement. The aim is to present data for deliberation as to how future energy efficiency improvement measures should be in the Asia-Pacific region. The chapters (Chapter 0 through Chapter 10) of the report to be worked out by Working Group III deeply involved in energy problems are 0) Introduction, 1) Scope of the report; 2) Socio-economic and emissions scenarios; 3) Technical and economic potential of GHG (greenhouse gas) emissions reduction; 4) Technical and economic potential of biological CO2 mitigation options; 5) Barriers, opportunities and market potential of technologies and practices; 6) Policies, measures and instruments; 7) Costing methodologies; 8) Global, regional and national costs and ancillary benefits of mitigation; 9) Sector costs and ancillary benefits of mitigation; and 10) Decision making frameworks. As the result of the survey, some actual technology transfer implementations are introduced covering branches closely related to energy efficiency improvement, which are branches of construction, traffic, industry, energy supply, and wastes. (NEDO)

FY 2000 report on information exchanges/analytical survey for improvement of energy consumption efficiency; 2000 nendo energy shohi koritsuka joho kokan bunseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of surveying the situation of the arrangement of methods of energy conservation promotion and the emissions trading system in developing countries by Japan having the effectiveness or in cooperation with developed countries, information was collected through the participation in international conferences related to energy conservation promotion, etc. and by visits at governmental organizations in charge in developed countries and developing countries. The results of the survey were classified into the following four items: 1) survey method; 2) exchanges of information on energy conservation in main 3 developing counties; 3) exchanges of information of energy conservation in the main developed countries; 4) exchanges of information of the emissions trading system (international trading system of energy conservation values (greenhouse effect gas emission right)). In 4), survey was made on the following: the emissions trading system for the inside of company group (BP-Amoco), the details of the emissions trading system for one country (the U.K.), the grapple with the emissions trading by a private trading organization (NATSOURCE Co.), and the handle with the emissions trading system by each of the OECD countries. (NEDO)

FY 1999 research and development results. Technological development of superconducting power storage systems; Chodendo denryoku chozo system gijutsu kaihatsu 1999 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for technological surveys on the superconducting power storage system (SMES) for cost reduction and high-temperature SMES, and the FY 1999 results are reported. The SMES cost analysis/evaluation program establishes the (basic flow for cost analysis/evaluation) for cost evaluation. The program for the SMES systems for system stabilization sets the specifications of 100MW as output and 15kWh as storage capacity at the generator end and intermediate switching station. The program for SMES systems for load fluctuation compensation and frequency control sets the specifications of 100MW as output and 500kWh as storage capacity at the installation site as the load end, and the investigation of high-temperature SMES technology is conducted on the conceptual designs of the SMES for system stabilization application (100MW, 15kWh) of toroidal coil type. The optimization designs are made for these systems. The investigation of the technology for high-temperature superconducting wires involves fabrication on a trial basis and evaluation for the characteristic evaluation coils, and characteristic measurement and applicability investigation for the large-current short conductor. (NEDO)

Load leveling of the Tohoku Electric Power Co. Development of ice storage cold-water manufacturing unit/solid organic waste treatment equipment using midnight power for cold district; Tohoku Denryoku no fuka heijunka. Kori chikunetsu reisui seizo unit no kaihatsu, shin`ya denryoku riyo kanreichi muke kokei yuki haikibutsu shori sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

An ice storage cold-water manufacturing unit that can manufacture cold water at a stable temperature near 0degC by using midnight power and a solid organic waste treatment facility were developed. The high-speed melting of ice is required to stabilize the cold-water temperature. Therefore, experimental investigation was performed. A piece of flake-shaped ice whose surface area and storage quality are balanced was used. A system that melts ice using the melting tank installed outside an icebox, and a high-speed melting system of ice based on the mixing unit installed in a melting tank were also used together. In the validation test of a prototype for smaller food factories, the following was confirmed. Manufacturing of cold water at about 1degC, amount of cooled water, stability of output water temperature for a change in water temperature, and good storage of ice in an icebox. In the prototype developed for a solid organic waste treatment facility, satisfactory performance was confirmed for following. Temperature in a fermenter when wastes were put, moisture content in a fermenter, pH value, net loss when the refuse of fish is put, and saving of an electricity rate. 6 figs., 2 tabs.

Optimal operation by dynamic programming in a solar/electric hot-water system; Taiyonetsu/denryoku kyuto system no doteki keikakuho ni yoru saiteki un`yo

Energy Technology Data Exchange (ETDEWEB)

Edo, S; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)

1997-11-25

With regard to utilization of a solar/electric hot-water system, a discussion was given by using a dynamic programming method on operation of a system which minimizes power charge. The discussed system is an installation in a welfare facility accommodating 100 persons, where solar heat is stored in a heat storage tank from a heat collector, and utilized for hot water supply. If the solar heat is insufficient for required hot water quantity, the water is heated by using an electric heater. The discussion compared the system operation using the dynamic programming method with the following two systems: the operation method 1, which does not utilize insolation forecast and the operation method 2, in which insolation forecast is utilized and late-night electric power is utilized for heating water in shortage. As a result of the calculation, the operation using the dynamic programming method conducts heat storage by utilizing the late-night power even if insolation is sufficient in winter in order to suppress heating by utilizing late-night power for days with less insolation. Thus, suppression is given on excessive utilization of day-time power and on rise in annual maximum power demand. It was found that the present system reduces power consumption by 37.7% when compared with the operation method 1, and 22.7% when compared even with the operation method 2. 3 refs., 5 figs., 3 tabs.

Thermochemical recuperative combined cycle with methane-steam reforming combustion; Tennengasu kaishitsu nensho ni yoru konbaindo saikuru hatsuden no kokoritsuka oyobi denryoku fuka heijunka taio

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, R.; Essaki, K.; Tsutsumi, A. [The University of Tokyo, Tokyo (Japan). Dept. of Chemical System Engineering; Kaganoi, S.; Kurimura, H. [Teikoku Sekiyu Co., Tokyo (Japan); Sasaki, T.; Ogawa, T. [Toshiba Co., Tokyo (Japan)

2000-03-10

Thermochemical recuperative combined cycles with methane-steam reforming are proposed for improving their thermal efficiency and for peak-load leveling. For targeting higher thermal efficiency, a cycle with methane-steam reforming reaction heated by gas turbine exhaust was analyzed. The inlet temperature of gas turbine was set at 1,350 degree C. Low-pressure steam extracted from a steam turbine is mixed with methane, and then this mixture is heated by part of the gas turbine exhaust to promote a reforming reaction. The rest of the exhaust heat is used to produce steam, which drives steam turbines to generate electricity. The effect of steam-to-methane ratio (S/C) on thermal efficiency of the cycle, as well as on methane conversion, is investigated by using the ASPEN Plus process simulator. The methane feed rate was fixed at constant and S/C ratio was varied from 2.25 to 4.75. Methane conversion shows an increasing trend toward the ratio and has a maximum value of 17.9 % at S/C=4.0. Thermal efficiency for the system is about 51 % higher than that calculated for a conventional 1,300 degree C class combined cycle under similar conditions. A thermochemical recuperative combined cycle is designed for peak-load leveling. In night-time operation from 20 : 00 to 8 : 00 it stores hydrogen produced by methane steam reforming at S/C=3.9 to save power generation. The gas turbine inlet temperature is 1,330 degree C. In daytime operation from 8 : 00 to 20 : 00 the chemically recuperated combined cycle operated at S/C=2.0 is driven by the mixture of a combined cycle operated at constant load with the same methane feed rate, whereas daytime operation generated power 1.26 times larger than that of the combined cycle. (author)

Results of photovoltaic power generation system operation in Tokyo Electric Power Company; Tokyo Denryoku ni okeru taiyoko hatsuden setsubi no unten jisseki ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fukuda, H; Itokawa, K [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1996-10-27

A report was made on the measurement of data and the results of the analysis at 14 sites of photovoltaic power generation facilities operated under system interconnection by Tokyo Electric Power Company. This type of system is provided in 40 sites as of the end of fiscal 1995, generating 479kw. The items measured were the generated electric energy at all 14 sites, and the quantity of solar radiation, outside air temperature, panel temperature, etc., at limited sites; and the capacity of each equipment, azimuth and inclination of the panel were also recorded simultaneously. Hourly values were used for the analysis. Five minute values were utilized, however, in the examination of the cause of lowered output and in the situation recognition of the influence of the shade or the change of weather. The utilization factor of the facilities was in the average 10.8% in fiscal 1994 and 10.7% in fiscal 1995. The factor decreased slightly unless the panel azimuth faced due south. The utilization factor at the panel inclination of 35 degrees and 45 degrees showed both 10.4% through the year making no difference. The system seemed to show no overwhelming possibilities in coping with electric power demand. The reason was that deviation existed for 2 hours or so in the peak and that reliability was low as basic power facilities. However, it was determined that the system be continuously examined in future. 9 figs., 1 tab.

Fiscal 1999 technical survey report. Basic project on international cooperation on energy consumption improvement, etc. (Japan International Cooperation Center project on promotion of exchange of specialists); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Kokusai kyoryoku center jigyo suishin senmonka koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Specialist related to the governments of Thailand, Malaysia, and Indonesia where NEDO (New Energy and Industrial Technology Development Organization) implements its model projects were invited. They exchanged opinions with officials of the Japanese Government and affiliated organizations over measures for effective energy utilization. Opinions were also exchanged over the response of energy-consuming industries, development of technologies, and the status of their adoption. Activities of government-related participants are described below. Under a Model Project for Utilization of Waste Heat from Incineration of Industrial Waste at Industrial Estate, five Thai people with Industrial Estate of Thailand visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Keiyo Food Industrial Park. Under a model project on the recovery of waste heat from paper sludge incineration, four Malaysian people with Ministry of Energy, Communications and Multimedia or with Energy Center visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Japan Paperboard Industries Co., Ltd. Under a model project on the utilization of paper sludge and solid waste, four Indonesian people with Ministry of Industry and Trade or with Ministry of Mines and Energy visited Ministry of International Trade and Industry, NEDO, Babcock-Hitachi K.K., and Oji Paper Co., Ltd. (NEDO)

Study of recent fuel oil cost in air lines (Part 2). Saikin no airline no nenyuhi ni kansuru ichikosatsu (2); Nenryo shohi to hiyo tai koka

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Yoshikazu.

1989-03-01

Through an arrangement of published data about American air lines during 1985 through 1987, the overall expense vs. transportation fee (expense vs. effect) was studied as a main viewpoint. As a result, the fuel oil cost, even in case of wide fuselage plane, high in transportation efficiency, was high in ratio, 32 to 52% (3 to 5 times as high as that 12 to 14 years ago), and fluctuated connectedly with the oil price. While the jet fuel price fluctuated connectedly with the oil price per equal volume with 1.3 to 1.4 of price ratio. Further, the flight range ratio was recorded to be approx. 0.06 to 0.24 km/kg. While the transportation efficiency was lower than approx. 5000kg*km/kg with a wide range of overall expense, approx. 9 to 87 cents per compensative transportation ton*km. Because even a sudden decrease in transportation quantity did not decrease the overall expense, it was known to be important in management to secure the transportation quantity. 30 refs., 15 figs., 1 tab.

Report on commissioned business for fiscal 1997. Development of new power storage system for cells and development of technology for distributed power storage (research for a zinc/air cell system for automobiles); 1997 nendo itaku gyomu hokokusho. Shingata denchi denryoku chozo system kaihatsu bunsangata denryoku chozo gijutsu kaihatsu (denki jidoshayo aen kuki denchi system chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the above, it is discussed whether such a system is feasible in Japan. A zinc/air cell system requires some special plants for zinc regeneration, etc. It is necessary to build a zinc refining plant and to install dozens of electrode replacing facilities in an area dozens of kilometers in diameter with the plant at the center. For such a system to be functional, there have to be several tens of thousands of automobile users in a limited area. In Japan, so large a number will not be found anywhere even if the appeal is directed to those in the postal service and electric utilities. There will be no economic success in Japan, different from in Germany. As for the economic comparison between a zinc/air cell system and natural gas system, the two will be equivalent to each other as far as the use of the quick filling stations for the natural gas automobiles remains as it is. When the number in consideration is so large as several tens of thousands, however, the natural gas system will turn out to be economically superior to the zinc/air cell system. 19 figs., 29 tabs.

Fiscal 1998 research report on the total electric power loss reduction project for Myanmer; 1998 nendo Myanmer koku denryoku soshitsu sogo teigen project chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of Japanese clean development mechanism, study was made on reduction of greenhouse effect gas emission from thermal power plants by reduction of power transmission and distribution losses of power systems in Myanmer. Study was made on technical power transmission and distribution losses for the national grid transmission system, 33kV sub- transmission system of Thaketa substation in Yangong city, and 6.6kV and 400V distribution systems of Latha and Lanmadaw townships in the downtown area of Yangong. Countermeasures for power loss reduction were considered on the basis of the study result. The loss reduction project plan includes a construction cost of 5,134,000US$, loss reduction of 7,726kW, and loss reduction of 33,213,000kWh. The project feasibility and profitability were evaluated by comparison between a financial internal rate of return (FIRR) and an opportunity cost assuming that a discount rate is the opportunity cost. As a result, FIRR was 17.36% and the discount rate was 8.89% in Myanmer. (NEDO)

Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

Energy Technology Data Exchange (ETDEWEB)

Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)

1997-11-25

Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

FY 2000 report on the survey of the stabilization of wind power generation power system, etc.; 2000 nendo furyoku hatsuden denryoku keito anteika nado chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of elucidating effects of output fluctuations at the time of quantity introduction of wind power generation, conducted were observation of wind characteristics in Hokkaido and analysis of the characteristics, estimation of fluctuations in wind power output, analysis of fluctuations in system frequency, etc. In the observation of wind characteristics, wind velocity/wind direction were measured at observation posts of 30 wind turbines installed at 16 sites in Hokkaido. Concerning the conversion into wind power output, 10 cases were selected such as the case of passage of low atmospheric pressure, etc., and the generator unit and wind firm were simulated in detail. In the estimation of wind power output, good agreement with the results estimated was confirmed at points very near to posts of observation of wind characteristics. As to the evaluation of effects of wind power generation to the system, power system frequencies were simulated using the models constructed and using capacity and kinds of frequency adjusted power source as parameter. As a result, it was indicated that there was a possibility of frequency's sharply fluctuating in case the surplus energy in frequency adjustment is reduced by fluctuations in demand and further in case wind power output is fluctuated. (NEDO)

Power load leveling and energy saving measures for office buildings. Power load leveling and energy saving technology for the new building of the Kobe branch of the Kansai Electric Power Co., and its effect; Office biru no denryoku fuka heijunka sho energy hosaku. Kobe shiten shinshaoku ni okeru denryoku fuka heijunka sho energy gijutsu to sono koka

Energy Technology Data Exchange (ETDEWEB)

Tsuchiyama, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

1999-06-10

This paper presents power load leveling and energy saving measures for heat source, air conditioning and lighting of the new Kobe branch building. The low-temperature hot-air system adopts an ice storage system, and reduces blowing power by 12 degreesC blowing in place of normal 16 degreesC blowing, and an initial cost by duct size reduction. The continuous air conditioning system levels an initial peak load of air conditioning as compared with normal air conditioning only for working hours for buildings with large heat capacity. In addition, as power load leveling measures for the whole building, the complete heat storage system using an underground internal melting type ice storage tank is adopted. Energy saving for lighting is achieved with a dimming lighting controlling its lighting output by inverter. The following effects are expected by these new technologies: Load leveling effect of 30%, energy saving effect of 20.2% and CO{sub 2} reduction effect of 24.1%. (NEDO)

The Fukushima War

International Nuclear Information System (INIS)

Pelletier, Philippe

2012-01-01

Friends (Tomodachi) to the prefecture of Miyagi and did not go into the prefecture of Fukushima. Wataru Iwata, the man behind 'Project 47', which unites the victims of nuclear disaster, is not afraid to talk of 'war'. According to him, 'the situation in Japan is looking more and more like one of war: the television, press, and Internet media are being urged to implement a voluntary gag order'; or, in other words, to curb their language and suppress their revolt. The disinformation is also provoking sentiments of war among some citizens, according to Tatsuru Uchida, professor emeritus of philosophy in Kobe, who evokes 'the anger of [major newspaper] readers who see it as a repeat of what happened during World War II'. Then there is the daily newspaper Asahi Shimbun, for which covering the Fukushima accident is like covering a war since the only information available is provided by a single antagonist, namely TEPCO (Tokyo Electric Power Company - Tokyo denryoku kabushiki kaisha). Moreover, perhaps we can talk of the 'war,' or at least defiance, of citizens against all types of authority, a war that is crystallizing new forms of confrontation. For essayist Sakaiya Taiici, 3.11 marks 'Japan's third defeat', after 1868 and 1945, thus implying that a war has indeed taken place

FY 1999 report on the survey of the basic cooperation project of enhancement of the international energy consumption efficiency. Project on promotion of exchanges with the persons concerned with government agencies, etc.; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo, kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Seifu kikan nado kankeisha koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of promoting the understanding of effective energy utilization and constructing corporative relations between countries, the persons concerned with government agencies of India, China, Indonesia, Vietnam, Myanmar and Thailand were invited to Japan, and exchanges of opinions were made on policies, technical development, the state of the introduction, etc. The persons concerned with governments of India, China and Indonesia participate in NEDO Forum 2001 to give lectures on the energy policy of their own. The persons sent from the Vietnamese government paid visits for survey to NEDO, Obayashi Corp., Kawasaki Heavy Industries, Ltd., Mitsubishi Materials Corp. and Taiheiyo Cement Corp. as reference of the model project on cement sintering plant power reduction. The persons sent from the Myanmar government paid visits for survey to NEDO, ECCJ, Chiyoda Corp., Yokogawa Electric Corp. and Cosmo Oil Co. as reference of the model project on energy conservation at fertilizer plant. The persons concerned with the Thai government paid visits for survey to the plants concerned with the model project on residue combustion waste heat recovery facilities at paper mills and the model project on waste heat recovery at steel material heating furnace. (NEDO)

FY 2000 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 2000 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Looking for effective measures for enhancement of energy consumption efficiency in the Asia Pacific region, survey was made of the state of study of measures against global warming in the 3rd IPCC report and the state of study of the incidental convenience. The survey was made in the following two fields: 1) research analysis in study of the 3rd IPCC report; 2) research analysis of the convenience incidental to measures against global warming. 1) is composed of IPCC activities and the 3rd assessment report, and the developmental state of global warming prevention technology and potential of greenhouse effect gas reduction. Subjects on the prevention technology are the technology for enhancement of energy consumption and development of non-fossil fuels. Physical/chemical CO2 fixation is also studied. 2) is composed of the introduction, economic/social/environmental effects, international flow, reasons for different conclusion in every study, and fields of further study. Considered were global warming prevention measures, for example, economic/social/environmental effects of creation of the carbon tax, reduction in subsidy in energy sector, etc. (NEDO)

FY 1997 report on the field survey on country situations including efficient energy consumption. Vietnam; 1997 nendo chosa hokokusho (energy shohi koritsuka nado chiiki josei genchi chosa). Vietnam

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Field survey was made on the current state of and issues on energy in Vietnam. In Vietnam, firewood is in wide use as non-commercial energy, and sums to a half of total energy consumption. Other energies such as hydroelectric power, petroleum, natural gas and coal are self-sustainable. Commercial energy consumption in 1995 is estimated at 10,070,000t in oil equivalent, which is broken down into 23% for coal, 42% in oil, 5% for natural gas and 30% for electricity. Abundant water resources will form the mainstay of future electric power supply. Commercial production of oil started in 1986 becoming an oil exporting country. Several promising natural gas fields were discovered as the result of the exploration by foreign capital. Coal deposits are estimated to be nearly 3.5 billion tons, and most of them are anthracite. Electric power demand is growing at a higher rate than the economic growth of Vietnam. The growth rate of electric power demand is set to be 1.3 times that of GDP. Since construction funds for new plants cannot be satisfied with the national budget and domestic investment alone, the country is expecting foreign capitals. 21 figs., 36 tabs.

Research on adoption of graphic processing system into electric power facilities operation management. Denryoku setsubi kanri gyomu ni okeru zukei shori system no tekiyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Jitsubuchi, Yoshiyasu; Uryu, Kenji; Terasaki, Naoaki (Kyushu Electric Power Co., Inc., Fukuoka (Japan))

1989-03-30

In the technical department of electric power companies, there are innumerable single line diagram, machinery arrangement plan and other facilities drawings. Based on those drawings, facilities planning, work design, construction plan, maintenance and management data, etc. are made, for which making heightening is desired in efficiency of drawing filing management. Therefore, research was made on the adoption of CAD technology through modeling power transmission line, and power generating and transforming station operation management. First for the application of power transmission facilities, the power transmission line plan and facilities information were planned to be unified in management. Ie., the power transmission line plan and profile being shown on the display, symbols of steel towers, cable lines, etc. were further picked by mouth to easily substantiate the facilities. While image input and CAD of drawing were made in combined treatment. Then for the application to the power generating and transforming facilities, the single line diagram and facilities information were unified in management, together with demonstration of data interchangeability among different kinds of CAD system. 13 figs., 9 tabs.

Fiscal 1997 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 1997 nendo chosa hokokusho (energy shohi koritsuka chikyu kankyo eikyo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper surveyed the state of studying the measures against global warming in the third assessment report of the Intergovernmental Panel on Climate Change (IPCC) and made analyses of the trends of preventive measures for global warming in other countries, aiming at presenting data for studying the future enhancement of energy consumption efficiency in the Asia Pacific region. In the U.S., a report was taken up from Executive Office of the President which is entitled `the federal government R and D of energy for solution to problems in the 21st century.` The report made analyses of the federal government R and D of energy and at the same time recommended an increase in R and D budget and reinforcement of the organization of the Department of Energy. In Europe, the carbon tax, CO2 tax, energy tax, etc. are introduced or studied for reduction of CO2 emissions. OECD made public a report approved in May 1997 which is entitled `the environmental tax and green tax reform.` Also studied were the introduction and effects of the carbon tax aiming at reducing CO2 emissions in developing countries. More attention is being paid to economic effects predicted in case developed countries reinforce various kinds of measures for targeted reduction of greenhouse gases. 2 figs., 4 tabs.

Research and development in fiscal 2000 on element technologies for superconducting for electric power storage by using flywheels; 2000 nendo flywheel denryoku chozoyo chodendo jikuuke gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

With an objective to put flywheel electric power storage system into practical use, developmental research has been made on superconducting bearings that can support a rotating body having large load and rotating at high speed. This paper summarizes the achievements in fiscal 2000. In the study of enhancing the loading force for developing the element technologies for the superconducting bearings, specifications were established and fabrication was performed on the Y-based superconducting bulk for bearings, whereas the healthiness thereof was verified by measuring the trapped magnetic field distribution. This bulk was applied with vacuum impregnation treatment of an epoxy-based resin, to have fabricated a superconducting bearing model with a diameter of 180 mm class. Regarding the RE-based superconducting bulk, studies were carried out on a synthesizing method including optimization of the fabricating conditions, a columnar Sm-based bulk body with a diameter of 60 mm was fabricated, and its healthiness was verified. In the research of a rotation loss reducing technology, discussions were given on optimizing the magnetic circuitry to reduce the magnetic variation, by using the three-dimensional magnetic field simulation. In the evaluation test utilizing the existing test machine, the loading force of a 180-mm class-bearing model has shown 2105N at maximum. (NEDO)

Load leveling by a battery system in an electric power system with a photovoltaic system; Taiyoko hatsuden system ga donyusareta denryoku keito no chikudenchi ni yoru fuka heijunka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

1997-11-25

Storage battery-aided load leveling system is introduced into a power system having a photovoltaic power generation (PV) system, and the effect of the introduction is examined. For this purpose, the resultant improvement on the load factor and reduction in the annual cost are evaluated. Used as the load factor in the studies are the hourly records of power transmitted and received by Chubu Electric Power Co., Inc., in 1995. The output of the PV system is calculated using weather data collected in Nagoya City in the same year. Findings as the result of the studies are stated below. The maximum power is suppressed but a little if it is only the PV system that is introduced into the system. That is, a 2GW PV system introduced into the system suppresses the maximum power only by 0.5GW or less. The maximum power is suppressed more effectively when a storage battery is added, and it decreases linearly with an increase in the storage battery capacity. As for reduction in the cost, the reducing effect is higher when the rate of storage battery capacity/introduced PV capacity is higher in the presence of an introduced PV capacity of 0.8GW or more. 2 refs., 7 figs., 3 tabs.

Fiscal 2000 survey report. On-site survey of local state of affairs such as energy efficiency enhancement (Mongolia); 2000 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Mongoru

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Information was collected and surveys were conducted in Mongolia in an effort to acquire information necessary for energy related technical cooperation. The results were arranged in four fields which are (1) the current state of economy and the future trend, (2) current state of energy production/consumption and the future trend, (3) current state of power supply/demand and power facilities and the future trend, and (4) the current state of energy efficiency enhancement and the future trend. Mongolia has a population of 2.45 million at a density of 1.57/km{sup 2}, with Ulan Bator the capital inhabited by 0.69-million people. The mean air temperature is -10 degrees C in the period November through March, which makes heating indispensable. Power stations are of the heat and power cogeneration type. Power is supplied by the Eastern, Central, and Western systems, with the Central system producing 80% or more and independent power sources 10%. Its economy has already recovered from the confusion that followed the change of its national constitution. Mongolia's demand for power lingers low, however, and its facilities can produce more electricity than what is now wanted. Energy efficiency enhancing activities should start with the upgrading, reinforcement, and maintenance of the existing facilities and with independent power sources. (NEDO)

FY 1997 basic survey project (database construction project) for enhancing energy consumption efficiency in developing countries; 1997 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo. Database kochiku jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

NEDO is promoting a database construction project to collect and supply various technical/systematical information on energy related data and energy effective utilization. In FY 1997, about the Philippines, Indonesia and China, the data collected in a year were renewed, and seminar/workshop were held as a part of the promotion activities. About Thailand, Malaysia, Korea, Taiwan and Japan, Japan has independently been collecting the data. Also in FY 1997, Japan arranged the existing data and arranged/collected the data. About Vietnam, India, Myanmer and Pakistan, which became the objects for the project newly in FY 1996, the state of data arrangement was confirmed and the data were collected. Moreover, functional improvement of the system was made so that each country can use the database more easily and maintain the data independently. (NEDO)

FY 1998 annual report on the leading fundamental research and development of AC superconducting power apparatuses (New Sunshine Project); 1998 nendo koryu chodendo denryoku kiki kiban sendo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to propose fundamental research and development of AC superconducting power apparatuses, the FY 1998 efforts were directed to studies on the effects of introducing superconducting apparatuses, making proposals of development programs, literature (including patent publications) surveys on trends of research and development at home and abroad, and making proposals for technological breakthroughs. Results of the studies for evaluating economic efficiency of these apparatuses and the effects of their introduction indicate that the promising apparatuses for eventual commercialization include superconducting cables, current limiters, field power generators, transformers and flywheels. The superconducting cables are expected to greatly reduce losses and hence CO2 emissions. The superconducting current limiters are promising means to control short-circuit current increase in the trunk power systems in which they are used. The superconducting transformers are expected to reduce losses and hence CO2 emissions. The project of fundamental research and development of AC superconducting power apparatuses has proposed the fundamental technological research themes aimed at development of the elementary techniques prerequisite for realizing these 3 types of apparatuses and reflection of the required apparatus specifications in development of the cable materials. (NEDO)

FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

Fiscal 1997 research report. Basic research project on improving energy consumption efficiency in developing countries (Database construction); 1998 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo hokokusho. Database kochiku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

The New Energy and Industrial Technology Development Organization (NEDO) in fiscal 1993 started a database construction project, which involves energy conservation related primary information on the 11 countries concerned, for encouraging 11 Asian countries, namely, Japan, China, Indonesia, the Philippines, Thailand, Malaysia, Taiwan, Korea, Vietnam, Myanmar, and Pakistan, to promote their energy conservation endeavors. As part of the database construction effort under this research project, the so-far accomplished collection of and analysis into energy related information about the countries, surveys of the utilization and popularization of databases, and development of database systems are taken into consideration. On the basis of these efforts to improve on the database systems for enhanced operability, a program is formulated for database diffusion under which data are collected and updated for storage in databases. Also exerted under the program are endeavors to make use of the above-said database systems and to disseminate the constructed databases into the 11 countries for effective utilization. In the future, it is desired that the NEDO database will win popularity in the 11 countries and be utilized in their formulation of domestic energy conservation policies. (NEDO)

Achievement report for fiscal 1999 on New Sunshine Program. Frontier research and development of basic superconductive AC power generation equipment; 1999 nendo koryu chodendo denryoku kiki kiban sendo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of the New Sunshine Program of the Agency of Industrial Science and Technology, a 2-year survey and research is conducted beginning in 1998 on the effect of the introduction of superconductive power equipment for the facilitation of the progress of research and development of basic power equipment which utilizes AC (alternating current) superconductivity. Frontier research and development has been started of basic AC superconductive power equipment for clarifying the tasks to solve in the development effort and for preparing an efficient research and development plan. This fiscal year's endeavor covers the survey of the effect of the introduction of superconductive power equipment in addition to the preparation of a basic plan for the research and development of basic AC superconductive power equipment for fiscal 2000 and afterward, continued survey of research and development trends in and outside Japan for the review of the result achieved in the preceding fiscal year, development of AC equipment element technologies utilizing conduit type semiconductors as a basic study for the embodiment of AC superconductive equipment, and a study for elucidating the mechanism of resistance generated in a superconductive current limiter. Furthermore, papers on the superconduction technology released so far are investigated, and technology development trends and efficient research techniques are put together into a technological information database. (NEDO)

Achievement report for fiscal 1999 on New Sunshine Program. Frontier research and development of basic superconductive AC power generation equipment; 1999 nendo koryu chodendo denryoku kiki kiban sendo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of the New Sunshine Program of the Agency of Industrial Science and Technology, a 2-year survey and research is conducted beginning in 1998 on the effect of the introduction of superconductive power equipment for the facilitation of the progress of research and development of basic power equipment which utilizes AC (alternating current) superconductivity. Frontier research and development has been started of basic AC superconductive power equipment for clarifying the tasks to solve in the development effort and for preparing an efficient research and development plan. This fiscal year's endeavor covers the survey of the effect of the introduction of superconductive power equipment in addition to the preparation of a basic plan for the research and development of basic AC superconductive power equipment for fiscal 2000 and afterward, continued survey of research and development trends in and outside Japan for the review of the result achieved in the preceding fiscal year, development of AC equipment element technologies utilizing conduit type semiconductors as a basic study for the embodiment of AC superconductive equipment, and a study for elucidating the mechanism of resistance generated in a superconductive current limiter. Furthermore, papers on the superconduction technology released so far are investigated, and technology development trends and efficient research techniques are put together into a technological information database. (NEDO)

Fiscal 2000 research report on the energy consumption survey for popularizing stationary fuel cell systems; 2000 nendo teichiyo nenryo denchi no fukyu wo mokutekito shita energy no shohi ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A survey was conducted about the current state of domestic energy consumption for studying the feasibility of a stationary energy system using the polymer electrolyte fuel cell. A study relative to domestic energy consumption dealt with transition in the energy consumption rate, dependence on locality, and the effect of the makeup of residences. The monthly and hourly patterns of demand for heat for hot-water supply were referred to power consumption data broken down by time zone, and it was found that approximately 1kW output would be suitable for this purpose. A study was made about the pattern of operation that such a fuel cell system should follow, and it was learned that a pattern in which 'the system operates according to the imposed load starting at seven o'clock in the morning when the electricity rate switches to the higher and the output does not exceed what is necessary to meet the daily demand for heat.' This method was found to assure the most efficient way of operation covering more than 80% of the need for hot water and electricity. In a study of consumption of energy for business, feasibility was suggested to exist in the installation of systems of 30kW or less at small hotels, barber shops and beauty parlors, restaurants, schools equipped with minor-scale food service, small hospitals, clinics, and the like. (NEDO)

Fiscal 1999 technical survey report. Basic survey for energy consumption rationalization and cooperative project on energy conservation seminar; 1999 nendo energy shohi koritsuka kiso chosa oyobi sho energy seminar kyoryoku jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

A survey was conducted of Myanmar's energy-consuming industries for exploring the feasibility of introducing practical energy conservation techniques and facilities to this country and for collecting basic data for the implementation of the project in the future. On the other hand, some lecturers were dispatched to an energy conservation seminar which was held in cooperation with the Government of Myanmar. Visited during the basic survey were (1) the Kyan Gin plant of Myanmar Ceramic Enterprise representing Myanmar's cement making industry, (2) the Thanlyin plant of Myanmar Petrochemical Enterprise representing Myanmar's oil refining industry, and (3) the Siftong plant of Myanmar Paper and Chemical Enterprise representing Myanmar's paper making industry. In the study of energy conservation measures for which stabilization of operation through reinforced facility maintenance and management were required, it was concluded that much time was necessary before Japan's advanced energy conservation technologies might be introduced into Myanmar. Three to six propositions were presented to each of the three plants. At the seminar, the importance of energy conservation promoting measures and the results of the basic survey were introduced to the audience. A lecture meeting was also held to familiarize some participants with NEDO-DB (Database of New Energy and Industrial Technology Development Organization). (NEDO)

Development of a new electric battery electric power storage system. Results of the 12-year R and D; Shingata denchi denryoku chozo system kaihatsu. 12 nenkan no kenkyu kaihatsu no seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The paper described the results of the R and D which have been continued for 12 years on a new electric battery electric power storage system (load leveling function). The electric batteries for study were Na-S, Zn-Cl, Zn-Br, and redox type. Charge/discharge operation of 211 times was conducted of a pilot plant with a Na-S battery 1,000kW and 8-hour capacity. The overall efficiency of system was 71.5-76.0%, and the energy efficiency of battery was 86%. As a whole, the performance was able to be confirmed which can fulfil a developmental target. The system overall efficiency of 65.9% and battery efficiency of 76.1% were obtained. The experiment on battery life was carried out at plant together with the pilot operation. The mean life of Na-S battery was estimated at 800 cycles, and that of Zn-Br battery at 500-800 cycles. The effectiveness of the new electric battery electric power storage system was technically verified. For the future commercialization, studies on the following are needed: enhancement of reliability, easiness in maintenance/inspection, size reduction, cost reduction, etc. (NEDO)

Present situation of the electric power storage technology and its future outlook. IV. ; Compressed air energy storage. Denryoku Chozo gijutsu no genjo to shorai tenbo ni tsuibe. IV. ; Asshuku kuki chozo

Energy Technology Data Exchange (ETDEWEB)

Kadoyu, M. (Central Research Institute of Electric Power Industry, Tokyo (Japan))

1991-03-20

The compressed air energy storage gas turbine power generation system is paid attetion to as a load levelling power source in view of the recent increase in electric power demand. The paper describes features, cavern construction technology, economy and future expansion of the system. In this system compressed air made by use of cheap night-time electric power is stored in underground spaces or underwater facilities. Burning the fuel together with this compressed air in the daytime, the gas turbine power generation is conducted. Several examples overseas of this system are reported including a 290,000KW class in Germany. A key technology of the system is how safely and cheaply a large amount of hih-pressure air can be stored. In Europe and America, caverns of hundreds of thousand m {sub 3} are constructed in the rock salt cavern which can be excavated by a water jet. In consideration of storing it in rock beds in Japan where there are no rock salt caverns, NEDO started 1990 a 9-year construction plan of a 35,000 KW class pilot plant at Kamisunagawa, Hokkaido. 2 refs., 5 figs., 1 tab.

Technologies for simulation improvement of NOx and PM emissions and fuel consumption of future diesel engines for heavy-duty trucks; Shorai no ogatasha diesel engine ni okeru NOx, PM, nenryo shohi no kaizen

Energy Technology Data Exchange (ETDEWEB)

Shimoda, M.; Shimokawa, K.; Uchida, N.; Tsuji, Y.; Yokotaa, H.; Hosoya, M. [Hino Motors, Ltd., Tokyo (Japan)

1999-01-01

Future diesel engines for heavy-duty trucks are required to have significantly low NO{sub x} and PM emissions and fuel consumption characteristics. In order to improve these characteristics, various technologies including high pressure fuel injection systems, combustion optimization. high boost pressure turbocharging, EGR homogeneous charge compression ignition combined with multiple injections, and aftertreatment are discussed. As each technology has a number of challenges to overcome, it will take long before engines with these technologies are commercially available. In this paper, the research activities accomplished to date are reported. (author)

FY1998 survey report on the site surveys on regional situations in improvement in energy consumption (Cambodia and Bangladesh); 1998 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho (Cambodia, Bangladesh) chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to promote technical cooperation of Japan with Asia in the energy aspect, site surveys were carried out on improvement in energy consumption efficiency. Electric power supply in Cambodia is made mostly from EDC, whose power generation amount in 1997 was 310 million kwh, while the power sold was 230 million kwh, with 26.1% of the total generation amount, or 80 million kwh being wasted as the loss. Existing power generation facilities are old and small in scale, made by the former Soviet Union making the repair difficult. The loss is enormous because of aging in power distribution facilities, overload operation, and power stealing. The efficiency is extremely poor, whereas improvement in efficiency of the existing facilities is indispensable to cope with the anticipated increase in the demand. In Bangladesh, 90% of the power is generated by using natural gas produced in the eastern part of the country. Many power plants are experiencing decreased efficiency due to the facility aging and insufficient and improper maintenance. The power transmission and distribution departments have had a large loss in power, which has become one of the most important issues. The loss exceeds 30%. The government is trying to achieve efficiency improvement in the electric power business through introducing the principle of competition by establishing new private companies. However, this approach is facing severe objection from the governmental and public labor unions, making the future development opaque. (NEDO)

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (investigation on system introduction); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system donyu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

In introducing high-temperature superconducting flywheel power storage equipment to an electrical power system, adaptability is examined and evaluated concerning secondary effect that can be expected while a load leveling function is maintained. The 1998 plan is such that the functions and usages other than the load leveling are put in order for such equipment, and that the effect/adaptability in the case of the introduction into the power system is evaluated by means of simulation and literature studies. The high-temperature superconducting flywheel power storage equipment may be used for such purposes as energy adjustment for a short time, system voltage adjustment and emergency power source, other than the load leveling, on the basis of the characteristics that enable high speed control of active/reactive power and storage/release of energy. Enumerated, as the effects obtainable in introducing these uses into the power system, are enhancement in system stability, improvement in voltage stability, improvement in instantaneous voltage drop, maintenance of system frequency, compensation of fluctuating load, countermeasures against power outrage, and output leveling of intermittent power sources, and these effects were examined. (NEDO)

Report on results 1998. Technological development to create high quality crystal material for low loss power controlling element; 1998 nendo seika hokokusho. Teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This paper refers to the development of basic technology for manufacturing crystal materials of a large diameter and uniform properties for the purpose of sophistication and low loss of semiconductor controlling elements for electric power. An experiment was conducted using the drop tower of the underground agravity center. Results in fiscal 1998 were explained. With counter-measures taken in for improving measuring accuracy of an electromagnetic floating furnace, the accumulation and evaluation were performed of the highly reliable data of the surface tension and density of Si. The measurement of the viscosity coefficient of Si under micro-gravity was successful for the first time in the world, as was the measurement of the contact angle between solid/liquid, other than the measurement of specific heat, thermal conductivity and spectral emissivity of Si. The viscosity coefficient, unlike the conventional report, showed Arrhenius' linearity. In the comupter simulation, boundary data were exchanged between element analysis programs, developing a basic general analysis program as scheduled. The result of a micro simulation by molecular dynamics method was in agreement with the observation result by a transmission type electron microscope, bringing the first success in the world. In the Cz furnace model experiment, effect of rotation for example was elucidated on turbulence in the melt by using lasers. (NEDO)

Development of a forecasting method of a region`s electric power demand. 1. Forecasting economic and social indexes; Chiikibetsu denryoku juyo yosoku shuhono kaihatsu ni tsuite. 1. Keizai shakai shihyo no yosoku

Energy Technology Data Exchange (ETDEWEB)

Minato, Y. [Shikoku Research Institute Inc., Kagawa (Japan); Yokoi, Y. [The University of Tokushima, Tokushima (Japan)

1996-01-20

This paper relates to the forecasting method of the electric power demands (kWh and kW) of a region, approached by not only time series analysis but economic and social indexes. Those indexes, based on historical statistics such as census and establishment statistics, are rearranged from an administrative division to a managerial division of the electric power company, and applied as fundamental information for forecasting the area`s kWh and also sales promotion. This method of forecasting the area`s kWh is based on the concept that area`s kWh is strongly connected with the population their lifestyle and their activity within the region. In the paper, the framework of the computational model system and forecast result are discussed. The population, number of households and their members, and number of employed persons, are all evaluated. The forecasting method of the area`s population proposed here is based on the concept that the transition of population consists of both natural growth and immigration. By estimating both factors, the future area`s population can be easily forecasted. The information of whether the population is increasing or decreasing is useful for forecasting the region`s kWh and required sales promotion. 8 refs., 8 figs., 3 tabs.

Fiscal 1999 achievement report. Development of technologies for creating high-quality crystalline materials for low-loss power control devices; 1999 nendo teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Researches are conducted for the advancement of, and loss reduction for, semiconductor devices for controlling electric power. Physical properties of molten semiconductors etc. are accurately measured in a microgravity environment and computer simulations are performed, which are for the production of larger-diameter, higher-quality semiconductor crystal materials. In the measurement of physical properties of molten semiconductors etc. carried out at JAMIC (Japan Microgravity Center) free-fall facilities where a high-quality microgravity environment is available, measurements are made of the surface tension, density, viscosity index, heat conductivity, and vertical spectral factor of the molten silicon. Solubility is measured of silica, silicon nitride, and silicon carbide, and, in equilibrium with these, the oxygen, nitrogen, and carbon in molten silicon, and highly reliable data are obtained. As for the comprehensive analysis code developed under this subject, the X-ray image data of the surface of a solid solution, collected from a crystal growing in a small Cz furnace at the NEC Fundamental Research Laboratories, and data of oxygen concentration in the silicon crystal agree excellently with the result of calculation, which suggests that the code is reliable. (NEDO)

Research and development of a high-temperature superconducting flywheel energy storage system. Research and development of the New Sunshine Program; Furaihoiru denryoku chozo shisutemu kenkyu kaihatsu. Nyu sanshain keikaku ni motozuku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Y. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1999-11-25

The project conducted by NEDO for developing a high-temperature superconducting flywheel energy storage system is introduced; the two test results of fundamental studies are described. One is the measurement of levitation force and rotation loss of superconducting magnetic bearings composed of oxide superconducting bulks and permanent magnet composite. Two types of superconducting magnetic bearings. axial and radial types, were fabricated and tested. The other test was the fabrication and testing of two functional models. A small-sized superconducting flywheel model of the 0.5 kWh class was fabricated and tested. A medium-sized rotating functional model of the 10 kWh class was fabricated as well. (author)

Research and development of a superconducting flywheel power storage system in fiscal 1998. Research and development of rotation control technology; 1998 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. Kaiten seigyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Element technology research was performed on 'rotation control' aimed at practical application of a 10-MW class high-temperature superconducting flywheel power storage system. As part of the research, researches were carried out on small-size and middle-size models, low-loss control type magnetic bearing, and large-size models. For the small-size model, as a result of performing performance tests on the protective bearing by using a testing machine, it was revealed that the model is free of problems in the test for up to 5000 rpm. For the middle-size model, fabrication and installation were completed on a middle-size rotation control testing equipment having CFRP-made flywheel with a diameter of 1 m. In the control type bearing, as a result of adopting a homo-polar type magnetic pole, the rotation loss was reduced to about 1/5 of that of a hetero-polar type. The amount is about 75 W (12000 rpm) when the bias current is 1.5 A. Concept design was implemented on a 2-MWh flywheel bearing system supported with a high-temperature superconducting magnetic bearing as a full-size flywheel. The CFRP-made flywheel has a diameter of 4 m, and a circumferential velocity of 1200 m. (NEDO)

Customer prime s choice between quality and price of electric service. Denryoku hinshitsu to kakaku ni taisuru juyoka no sentaku. ; Ogata computerter dot user ni okeru back-up dengen kiki sentaku no suryo bunseki

Energy Technology Data Exchange (ETDEWEB)

Fujii, Y.; Matsukawa, I.

1990-03-01

This study is done for the purpose of numerically analyzing how customers react to make their choice between quality and price, as well as to evaluating the marketability of the new electric service differentiated by quality, on the assumption that electric utility is capable of providing the multi-product of the service with various combinations instead of the conventional single product between price and quality. An analysis was made for the customers like the large-scale computer users those who attach importance to quality. As for the method of the analysis, the choice (the introduction of emergency power source or uninterruptible power system) which have been actually done by the customers for the following two conditions, were used as the model of the analysis: The one was the standard of the requirements for the quality of electric power, of which requirements were composed of the two factors, such as the reliability on power supply and momentary voltage drop; The other was the cost (purchased power price plus investment by consumers for back-up power system) necessary to maintain the quality. Consequently, it was found that in order to heighten the competitiveness for the competition in electricity market, electric utility had to establish their service rate corresponding to the load, as well as that the quality was a important strategic factor for them. 30 refs., 10 figs., 9 tabs.

FY 1995 annual report on development of techniques for creating high-quality crystalline materials for low-loss power controlling components; 1995 nendo teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The R and D project is implemented for manufacturing high-quality semiconductor crystalline materials of large size and uniform characteristics, in order to improve semiconductors as components for controlling power systems, and reduce power loss. The semiconductor melts, in particular silicon melt, is highly reactive, readily reacting with the atmosphere and crucible holding the melt, and it is difficult to collect their thermal properties. Therefore, an electro-magnetic levitation furnace working under a microgravity is used, to dispense with a crucible for measurement of their properties in the absence of thermal convection. The preliminary tests using the furnace produce surface tensions of the melts, because Ge is less reactive than silicon, stable in the form of a GeSbTe compound, and not wettable with Al{sub 2}O{sub 3}, MgO, SiO{sub 2} or Si{sub 3}N{sub 4}. The measurement of electric resistance of InSb indicates that InSb has characteristics of a semiconductor when it is solid and a metal when it is liquid, as is the case with Si. The program codes are developed by each researcher, and combined with each other to establish the comprehensive thermal flow analysis program, which includes all of the aspects of the internal CZ furnace structure for growing the crystals. (NEDO)

OAM system based on TMN for utility telecommunication network. Proposal of modeling method about managed objects; TMN ni motozuku denryoku tsushinmo no un`yo kanri system. Kanri object no sekkei shuho ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Hirozawa, T.; Yusa, H.; Otani, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Okamura, K. [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1996-03-01

To construct an advanced operation and management system for utility telecommunications management network (TMN), this paper proposes a modeling method of managed objects (MOs) required for managing and managed systems, such as an asynchronous transmission mode (ATM) exchanger. Flexible line setting and path switching control are required for the advanced TMN, which must cope with the extension and modification of functions, flexibly. Assignment of roles of managing sides and managed sides was determined. Then, structures of objects such as facilities and logic data, and their interaction were modeled. Common management functions and objects of each function were classified. Based on the TMN standard and MOs of the existing design peculiar to utility, new MOs peculiar to utility were defined in response to the models. The existing MOs can be effectively utilized, and the optimum MOs to be incorporated can be expected. The MOs peculiar to utility are added to the common specification of electric power industry. Since they can be reused for the extension and modification of functions, the cost can be reduced. The MOs applicable to path switching control of utility were designed as a trial. 9 refs., 16 figs., 10 tabs.

Introduction effect of a load levelling system in an electric power system with a photovoltaic and wind system; Taiyoko/furyoku hatsuden wo donyu shita denryoku keito ni okeru fuka heijunka shisutemu no donyu koka

Energy Technology Data Exchange (ETDEWEB)

Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

1998-12-05

Introduction effect of load levelling system by a battery in an electric power system by a battery in an electric power system with a PV and wind system is investigated. Charge and discharge power of the battery are determined from a load curve and every hour data of PV and wind output. Annual cost of the power system is calculated from the generating power and the capacity of each source via the installed utility capacity and the capacity factor. It is found that (1) the battery system reduces the maximum demand and improves the load factor, (2) the cost effect of the battery system when introducing the PV system is higher than that when introducing the wind system. (author)

Fiscal 1999 research report. Development of ultralow- loss power device technology (Survey on next-generation practical power semiconductor devices); 1999 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Jisedai power handotai device jitsuyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This research proposes the clear developmental policy and target for 'Development project of ultralow-loss power device technology' through the research on power electronics or advanced power semiconductor devices as key technology of conversion loss reduction for various power applications and power supply systems. Main research issues are as follows. A bidirectional current switch using P-MOS FETs is promising as an ace of power system interconnection control equipment. IEGT as MOS gate high-power device will be substituted for GTO gradually. SiC devices will play the leading part of low- loss power devices for inverters of power converters, power systems of electric vehicles, Shinkansen and maglev railways, power systems of information and communication systems, and DC power systems. Size and cost reduction of low-noise soft switching as application technology of power devices are possible by using active circuits. Development of high- efficiency low-noise compact inexpensive inverters is an important issue. Countermeasures against various losses of inverters are also described. (NEDO)

Fiscal 1996 research report. Basic research on energy consumption efficiency improvement for developing countries (Industry related survey for energy analysis); 1996 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo hokokusho. Energy bunsekiyo sangyo renkan chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

Inter-industry relations tables and energy statistics are combined for Asian countries for the preparation of energy analysis oriented inter-industry relations tables, which are used to metrically analyze Aisan nations' industrial structures and energy consumption structures for the ultimate purpose of grasping the magnitude of each industry's demand for energy. The tables prepared this year cover Korea, Indonesia, Thailand, and the Philippines. In Korea, the self-sufficiency rate of mineral fuels is low at 23.1%, which is due to its import of crude oil from abroad. It consumes 177.92-million tons (in terms of oil) of energy for its economic activities, with energy saving measures expected to work effectively here. Indonesia's mineral fuel self-sufficiency rate is high at 84.3% because it is an oil producing country. The energy it consumes for its economic activities is 179.37-million tons (in terms of oil), and energy saving measures will work effectively here. Thailand is a crude oil importing country. Its mineral fuel self-sufficiency rate is 33.4% and the energy its economic activities consume is 53.08-million tons (in terms of oil), and energy saving measures will work effectively in this country. The Philippines is a crude oil importing country and its mineral fuel self-sufficiency rate is as low as 4.8%. It consumes 22.71-million tons of energy (in terms of oil) for its economic activities, and energy-saving measures are expected to take effect here. (NEDO)

Basic project on the cooperation in enhancement of the international energy consumption efficiency. Survey of energy conservation potential by industry; 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Gyoshubetsu sho energy potential chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of looking for measures to promote the effective energy conservation in China, the potential energy conservation amount in general plants was surveyed and analyzed by industry. Activities were made in the following fields: 1) survey of the actual state of energy in main industries; 2) energy conservation potential in the cement industry in China; 3) energy conservation potential in thermal power plants in China. In 1), survey was made on 8 industries including the iron/steel industry and oil refining industry. In 2), survey was made of the actual state of the Liulihe cement plant and Shitou cement plant. The subjects extracted were the arrangement of instrumentation equipment such as the exhaust gas analyzer needed for combustion management, improvement of the air/fuel ratio of kiln, enhancement of cooling efficiency of clinker cooler, etc. In 3), the actual state of the Qinling power plant was surveyed, and it was made clear that high efficiency of 38% or more can be maintained if the appropriate use/maintenance management is made (coal unit consumption: 383g/kWh in Qinling and 309g/kWh). (NEDO)

Report on the site surveys in fiscal 1999 on the regional situations such as energy consumption efficiency improvement. The north-western part of China; 1999 nendo energy shohi koritsuka nado chiiki josei genchi chosa hokokusho. Chugoku seihokubu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports the site surveys in fiscal 1999 on the energy consumption efficiency improvement in the north-western part of China. Although blessed with affluent natural resources, the regional development is delayed because of geographical restrictions and harsh climate conditions. Power generation facilities include hydroelectric power plants with output of 7.81 million kW, thermal power plants with 13.89 million kW, and power wind power plants with 70 thousand kW. The demand is estimated to increase by 4.6% annually in average. Thermal power plants are those made by the former Soviet Union, having poor power generation efficiency, which is scheduled to be improved by facility modification. Automation is also behind the times. These situations have brought about low reliability, delay in building electric power network in agricultural districts, and transmission wire loss (reducing 8.1% loss to 6% is planned). The electric power charge systems also have various problems. Environmental measures are also an issue. Dissolution of energy shortage as a result of developing the north-western area can be said a key to the future development of China. Xinjiang Electric Power Company is considering wind power generation as the center of new energy utilization. Representative facilities utilize affluent wind power available in the topography of the Tenzan mountain range in the suburb of Urumqi, the facilities being made of Denmark. Photovoltaic power generation is exiguous in realizability for the time being in terms of cost. Expectation is placed on fuel cells. (NEDO)

Fiscal 1999 international energy conservation model project. Report on result of demonstrative research concerning cement clinker cooling system; 1999 nendo kokusai energy shohi koritsuka nado model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing energy consumption and CO2 discharge in a cement plant in Indonesia, R and D was conducted on new clinker cooling system, high performance kiln combustion system, and technology for steady kiln operation and control, with the fiscal 1999 results reported. In the research on the optimum clinker cooling system, a new type clinker cooling system (CCS) was developed in which air beams are applied only to stationary grate rows, in an air beam type clinker cooling system where cooling air is fed to each block, with grate plates used as the air duct. This year, in an actual machine testing equipment (capacity 2,500 t/d), the whole heat recuperation area was modified for the CCS, with the operation started since February, 1999, aiming at the optimal clinker cooling effect and high heat recovery efficiency. The heat quantity for the entire system showed a decrease of 60 kcal/kg in the heat consumption rate through CCS modification, kiln burner adjustment, etc. So long as the demonstration plant is concerned, design of a new type burner and study/design for the kiln stabilization were nearly completed. (NEDO)

FY 2000 report on the development of ultra low loss power element technology. Commercialization of next generation power semiconductor device; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Jisedai power handotai device jitsuyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the promotion of development of ultra low loss power element technology, survey was conducted on the present situation, future, etc. of various technologies/systems related to power semiconductor devices. In the industrial equipment field, it is predicted that power semiconductor devices will be increased in the field of application by enlargement of the defense field of IGBT, new MOS structure elements, etc. In the field of home appliances, possibilities are expected of switching loss reduction and electric noise reduction by making SiC high speed diode. As to the space photovoltaic power generation, SiC is expected for various semiconductors such as solar cells, FET for transmitter/amplifier of radio power electric transmission use micro waves, etc. Concerning the radio communication system plan using stratosphere platform, there are technical problems on communication equipment such as antenna and RF circuit, and the role of SiC device is expected to be large. The society where the electrification rate is 80% and fuel cell vehicles are used is a new paradigm, and it is necessary and indispensable to commercialize ultra low loss power elements using SiC. (NEDO)

Report on achievements in fiscal 1999 of New Sunshine Project. Development of superconductor power applied technologies. Research on total system; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu gyomu seika hokokusho. Total system nado no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To deal effectively with problems being actualized in electric power systems, it is necessary to introduce superconductor technologies into power devices, and achieve higher efficiency, density and stability in the power systems. To achieve the goal, development is being made on superconductor power applied technologies, whereas investigative researches are given on the effects of introducing the superconductor power applied devices to proceed the development effectively and smoothly. This project is also given evaluations on its research achievements. In the practical application of superconductor generators, all of the verification tests have been completed, with the model generator system linkage test as the final test. Design and fabrication technologies were established on a 200,000-kW class pilot generator after having gone through analyses made after the tests. Not only having achieved the initial technical value targets, the result presented reliability required for practical use of the superconductor generator, having exceeded the expectation. The research and development of the superconductor generator technologies under this project is concluded successful. The AC superconductor devices were developed by effectively utilizing the results of the leading researches on fundamental technologies for AC superconductor power device technologies as well as other results of the world's highest levels. (NEDO)

Fiscal 1998 research report (New Sunshine Project). Research on the total system for development of superconductor power application technology; 1998 nendo seika hokokusho (new sunshine keikaku). Chodendo denryoku oyo gijutsu kaihatsu total system no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report summarizes the fiscal 1998 research promoted as a part of New Sunshine Project 'R and D project on development of superconductor power application technology.' This project is composed of R and D of superconductor power application technology (Rank 1), study on the total system (Rank 2), and study on review of introduction effects (Rank 3). The project is promoting R and D of the prototype superconducting generator model and elementary technologies based on the basic plan mainly by the research association. The combination test of the developed armature and the multi- cylindrical rotor model or slow response excitation rotor model was finished, and the test of the quick response excitation rotor model is in promotion. Together with R and D of hardware, this project is also promoting R and D of software through review of the introduction effects of superconducting power equipment. In fiscal 1998, the pre- final review was carried out by the project review sub- committee. 2 times of the committee, 12 times of the sub- committee, and several times of the working group were held until March, 1999. (NEDO)

Basic investigation project for energy consumption efficiency improvement in developing countries. Invitation of engineers from developing countries (Vietnam, Philippines, and India); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Betonamu, Philippines, Indo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The International Center of Environmental Technology Transfer has invited seven engineers from Vietnam, eight from Philippines and two from India for human resource education project for environmental preservation in developing countries. Those who were invited are administrative officials and engineers who work at administrative agents, research institutes and corporations related to energy conservation and environment preservation. In this invitation program, lecturers were invited from governmental offices, universities and corporations according to their expertise fields to carry out lectures and site training. With respect to energy conservation, lectures were given on a `summary of energy saving methods` by a lecturer invited from the Chubu Governmental Department of Trade and Industry, and on an `introduction to new energies` by Prof. Shimizu at the Engineering Faculty of the Mie University. Both lecturers emphasized the necessity of energy conservation, and importance of new energies as clean energies. The trainees showed strong interest when they visited a `cement factory` and a `coal burning thermal power plant` as the key industries. Their experience would be reflected strongly on guiding operations of factories in their own countries. 56 figs., 15 tabs.

Fiscal 2000 achievement report. Model project for international energy consumption efficiency improvement (Model project for improvement of boiler and turbine efficiency); 2000 nendo seika hokoku. Kokusai energy shohi koritsuka tou model jigyo (Boira tabin koritsu kojo model jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-12-01

A project was implemented for Japan to transfer its energy conservation technologies for helping Indonesia conserve energy and reduce CO2 emissions, which occurred at Muara Karang Thermal Power Plant of an Indonesian power company named PT PJB. Items to be introduced are condenser tubes (material change from cupro-nickel to titanium), ball cleaning equipment, turbine gland seal improvement, air preheater improvement, thermal efficiency management system, and so forth. In this fiscal year, turbine gland seals and air preheater elements were manufactured, and the thermal efficiency management system was designed. As an dissemination activity, 10 engineers were invited to Japan from the Indonesian Ministry of Energy and Mineral Resources, PT PLN, and PT PJB. They attended a training program lasting approximately two weeks, which included study tours to the factories actually building the equipment to be introduced and field/classroom training/education on thermal efficiency management and others. The engineers actively performed their boiler improvement work back in Indonesia. (NEDO)

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

Survey report for fiscal 1993 on basic survey project for energy consumption efficiency improvement in developing countries. Database development project 5 (The Philippines); 1993 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo (database kochiku jigyo). 5. Philippines

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Volume 5 covers the Philippines. The database development project has two goals. One is to collect basic data for joint projects for preparing energy conservation master plans for China and Indonesia, and the other is to build a comprehensive database for 8 countries including the said 2 countries (China, Indonesia, the Philippines, Thailand, Malaysia, Korea, Taiwan, and Japan) for contribution to the enhancement of energy conservation in the region involved. This Volume 5, dealing with 5 countries out of the 8 excluding China, Indonesia, and Japan, accommodates data on the Philippines, with whom a data collecting contract has just been signed in this fiscal year, which cannot be appropriately accommodated in Volume 1. The data referred to just above include the progress marked in this fiscal year in the preparation for the collection of actual data about energy consumption in Filipino factories scheduled to be carried out in and after the next fiscal year. (NEDO)

Fiscal 1999 basic survey report for promotion of joint implementation. Project for overall loss reduction in Myanmar for thermoelectric power during transmission and distribution; 1999 nendo Myanmar koku karyoku sohaiden denryoku sonshitsu sogo teigen project hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With connection to the clean development mechanism (CDM) taken into consideration, a study is made about achieving greenhouse gas reduction in Myanmar through power generation facility heat efficiency improvement and power loss reduction. Taken up in the study are the Shwedaung power plant, the Mann power plant, and the power transmission system in the Mandalay District. The profitability of thermoelectric power facility improvement is calculated using the financial internal rate of return (FIRR), derivable from the cost of thermoelectric power facility improvement and the convenience to be created thereby, and using the opportunity cost in Myanmar. The result is then subjected to a feasibility study. Most effective for CO2 reduction is the addition or installation of advanced compound cycle power generation facilities which are also excellent in heat efficiency and power generation cost. The FIRR of thermoelectric power facility improvement is 9.4-12.8%, which means the effort is worth investment. Measures for decreasing power loss during transmission include the use of higher voltages, laying of new lines, employment of conductors thicker in size, and the installation of phase modifiers. The economic internal rate of return (EIRR) and FIRR are calculated for the study of feasibility. An analysis covering a 10-year period results in a 20.41% EIRR (exceeding the socially accepted discount rate of 10%) and a 17.56% FIRR (exceeding the general loan interest of 15%), which means that there is feasibility. (NEDO)

Study of two step constant current charging method with EV`s valve-regulated lead acid batteries for nighttime load leveling; Yakan denryoku wo yuko katsuyo dekiru denki jidoshayo namari denchi no nidantei denryu judenho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ikeya, T.; Mita, Y.; Iwahori, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Iwasaki, M.; Takagi, S.; Sugii, Y.; Yada, M.; Sakabe, T.; Kosaka, E.; Tsuchiya, H.; Kanetsuki, M.; Nasu, H.; Ono, M.; Adachi, K.; Narisoko, H.; Nishiyama, K.

1997-02-01

In the constant-current/constant-voltage charging method that has been in application for EV (electric vehicle) lead-acid batteries, power load is generated only at the initial part of the charging process, and therefore the method cannot be said to be sufficiently contributory to the levelling of power loads. In this report, a proposed 2-step constant-current charging method is assessed for applicability, and another charging method is introduced, which extends battery life and utilizes low-cost night-time power more effectively. It is found that the proposed 2-step constant-current charging method (1st step: 12A, 2nd step: 3A) completes the charging process in eight hours, that it assumes a charging pattern more suitable for contributing to the effective use of night-time power than the conventional method, and that it extends the battery life of approximately 170 cycles to approximately 300 cycles. In a study seeking for a charging method capable of utilizing night-time power more efficiently, the 1st-step current of 12A is increased to 30A for shortening the charging time, and then it is found that this change extends the battery cycle life and improves on charging efficiency. The conclusion is that possibilities are high that an increase in the 1st-step current prolongs the battery life cycle and shortens the charting time. 16 refs., 28 figs., 8 tabs.

Basic research on energy conservation in developing countries. Report of the International Conference on Adaptation and Mitigation Technologies for Climate Change; Hatten tojokoku energy shohi koritsuka kiso chosanado jigyo. Kiko hendo ni kansuru tekio kanwa gijutsu kokusai kaigi hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The International Conference on Adaptation and Mitigation Technologies for Climate Change was held based on the 1st Conference of the Parties in 1995 of the United Nations Framework Convention on Climate Change, and the 2nd evaluation report of the Intergovernmental Panel on Climate Change (IPCC). This report carries the outline of this conference and minutes. Japanese government had studied the framework of activities implemented jointly (AIJ) for emission control of greenhouse gases by voluntary workers jointly with developing countries. The government decided the basis of the AIJ Japan program in 1995, and approved the evaluation guidelines of this program including confirmed and considered matters which are necessary for government offices related to this program to evaluate and approve each project. IPCC approved the 2nd evaluation report in its general meeting in 1995. This conference was thus held to discuss strategic technology and international cooperation with participation of writers of the 2nd IPCC report, policy planners of Asian countries, Japanese industries, governmental offices and NGO.

International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). List of errata; 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo seigohyo. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The list of errata was prepared for the data book of the international measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). Corrected pages of the data book 1 (1990) are as follows: 187-190, 223-226, 259-262, 295- 298, 369-370, 387-388 and 405-406 on Malaysian data. Corrected pages of the data book 2 (1985) are as follows: 102-105 on Chinese data, 154 on common data, and 187-190, 223-226, 259-262, 295-298, 369-370, 387-388 and 405-406 on Malaysian data. (NEDO)

1998 Annual Study Report. Research and development of power storage by high-temperature superconducting flywheels (research and development of permanent magnet); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (eikyu jishaku no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The permanent magnets have been investigated and developed, for eventual commercialization of a 10 MWh power storage system by high-temperature superconducting flywheel. The permanent magnet rotors have been already developed in the previous years using a praseodymium-based magnet (Pr magnet) and neodymium-based sintered magnet (Nd sintered magnet), and the target rotational speed of 30,000 rpm has been attained. For development of the magnetic circuit to produce a stronger and smoother magnetic field, magnetic flux density of the Nd sintered magnet is measured. It shows a lower magnetic flux irregularity than the Pd magnet, but there is still room for further improvement. For development of large-size permanent magnet fabrication techniques, it is confirmed that the large-size Nd sintered magnet can be easily magnetized by partial magnetizing, as is the case with the Pr magnet. In this year, the irregular magnetic flux is three-dimensionally simulated, based on the results obtained in the previous years, to find that the simulated results are in good agreement with the observed ones. The measures to solve the problems are also investigated. It is also confirmed that the large-size ring magnet can be easily magnetized by partial magnetization. (NEDO)

FY 1999 Report on research and development of power storage by high-temperature superconducting flywheel. Research and development of permanent magnet; 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu eikyu jishaku no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The R and D program is implemented for permanent magnet, as part of the project aimed at commercialization of a 10 MWh-class high-temperature superconducting magnetic bearing type power storage system. A speed of rotation of 28,570 rpm is attained by using an iron intermediate ring for a Pr permanent magnet rotator and reinforcing the rotator with a plastic hoop reinforced with carbon fibers three-fold (CFPR hoop). The speed is increased to 31,300 rpm by interlacing carbon fibers also in the radial direction and replacing iron for the intermediate ring by titanium. The highest speed of rotation of 33,506 rpm is realized by the rotator of permanent magnet of sintered Nd. The magnetic circuit of stronger, more smooth magnetic field needs the permanent magnet of less uneven magnetic flux. The magnet is of a monoaxially anisotropic rare-earth metal, with four-fold magnetic ring bodies having fan-shaped small pieces arranged on each ring. Uneven magnetic flux occurs at the joint between these small pieces. The one-body-ring magnet of radially anisotropic, sintered Nd is developed, and incorporated in the repulsion type magnetic circuit, to reduce unevenness of the magnetic flux. (NEDO)

Let everybody think about energy problems (what to do with energy supply). Electric power storage as a trump to make load flat; Energy mondai wo minnade kangaeyo (energy kyokyu wo dosuruka). Fuka heijunka no kirifuda (denryoku chozo)

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T. [Tokyo Electric Power Co., Inc. (Japan)

1995-09-20

Difference of electric power load between day and night has been growing due to increase of need for cooling in summer. In the case of Tokyo Electric Power Co., Ltd., the power maximum in a day exceeds 2-fold of the minimum. As a means of making load flat, power storage is a last resort to improve operation efficiency and suppress generation cost. Various technologies for electric power storage are overviewed and a sodium-sulfur (NaS) cell is introduced, whose practical application in near future is expected as a novel technology for power storage. Pumped storage generation has been put into practical use widely, sharing 10% of the overall capacity for generation facilities in Japan. However, since proper sites for its construction have been limited, compensating technologies, using electric cells, air compression, super-conduction and flywheels are in progress of research and development. There are three types of electric cells being under development; NaS, Zinc-bromine, redox flow cells. The NaS cell uses highly active electrodes of Na(+) and S(-), and {beta} alumina as electrolyte, which is neither electron-conductive nor self-discharging. 2 figs., 2 tabs.

Density distribution of currents induced inside the brain in the heat part of the human model exposed to power frequency electric field; Denryoku shuhasu no denkai ni yori jintai model tobu nonai ni yudosareru denryu mitsudo bunpu

Energy Technology Data Exchange (ETDEWEB)

Chiba, A. [Yonago National College of Technology, Tottori (Japan); Isaka, K. [The University of Tokushima, Tokushima (Japan); Kaune, W.

1998-06-01

The health effect of the weak current induced in the human body as a result of the interaction between human body and power frequency electric fields has been investigated. However, the current density inside the head part tissues of the human body exposed to the electric fields has little been discussed. In this paper, the finite element method is applied to the analysis of the current density distributions of the head part composed of scalp, skull, cerebrospinal liquid and brain tissues. The basic characteristics of the current density distributions of the brain in the bead part of the axisymmetrical human model have been made clear. 13 refs., 12 figs., 2 tabs.

Fiscal 1998 research report. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

This project aims to prepare the inter-industry relations table and analysis model for energy analysis for every Asian country, and analyze the relation between energy consumption and industrial structure or final demand structure. The 1985 and 1990 inter-industry relations tables of each country were prepared in cooperation with the governmental organizations of China, Korea, Taiwan, Philippines, Thailand, Malaysia, Singapore and India. However, the 1987 and 1990 tables were prepared for China. In fiscal 1998, the project invited the representatives of each concerned organization, and held the international workshop together with Japanese specialists to discuss various issues related to not only table preparation but also data analysis. The following items were analyzed for every country: a change in final energy consumption, a dependence on coal in primary energy consumption, transfer of energy consumption to other energy resources, and an energy consumption rate in the whole industry. (NEDO)

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

Report on achievement in developing an ultra low loss power element technology. Survey on practical application of the next generation power semiconductor devices; 1998 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Jisedai power handotai device jitsuyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Trends were surveyed for development of an ultra low loss power element. Performance improvement has been progressed on power semiconductor elements by using Si as the raw material, but loss reduction has come close to the physical limit. SiC is expected of possibility to go beyond this limit. SiC is so very excellent that its band gap is two to three times greater, insulation breakdown electric field is 7.5 times higher, temperature to become a true semiconductor is three to four times higher than those of Si. The wide gap can reduce high temperature leaking current in p-n junctions, and the increased authenticity temperature can increase the upper limit for operation temperature. The insulation breakdown strength being higher by one digit can reduce the drift layer thickness, and is expected to dramatically reduce the loss. The problem is that high quality crystals have not been obtained to date. One of the promising application fields is electric vehicle. The device currently using the power element in the largest scale is used in frequency converting stations to link the 50-Hz power network in the eastern part of Japan to the 60-Hz network in the western part of Japan. Surveys were carried out on the Sakuma frequency converting station and the New Shinano substation. (NEDO)

Report on the FY 1999 R and D on high temperature superconducting flywheel energy storage. System design/evaluation (Comparative study and information collection); 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. System sekkei hyoka (hikaku kento, joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Following the previous fiscal year, a flywheel technology survey committee by men of learning and experience was organized to make a comparative study on various flywheel energy storage systems. Concerning the list-making for checking each element of the high temperature superconducting flywheel system, characteristics and reasons for employment of the small model and medium model were outlined in terms of the system structure (structure in single unit, structure in more than one units), flywheel, bearing, electrically-driven generator, etc. Also about the system in which no superconducting magnetic bearing is used, the information is collected in Japan and abroad through internet, etc., to outline the system. Further, main results obtained in the project were made public in main international conferences or academic meetings such as EUCAS and ISOTC108. At the same time, visits were paid to research institutes such as Cambridge University in the U.K. for the purpose of supplementing the survey so far made, to investigate the recent trend of the research. (NEDO)

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (system design/evaluation (comparative assessment/information collection)); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system sekkei, hyoka (hikaku kento, joho shushu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

For the purpose of evaluating the basic characteristics of high-temperature superconducting magnetic bearings (SBM), a system model is designed, experimentally manufactured and tested, which is embodied in the design/evaluation of a large-scale system, with an investigation carried out for the introduction of the system into an electrical power system. In this framework, an examination and research were conducted for the system design technology on which each component technology in the system structure can be applied consistently in the system. In the comparative assessment of various flywheel power storage systems, the specifications and achievements were compared in the component elements of the flywheel systems developed in Europe, America and Japan through the literature studies and the field survey, with examination performed towards the future development. As a result, it was found that, in America, bearings were all SMB's without control. Boeing's objective for the development is 10kWh or so in view of convenience for transportation and is prone to arrange it in numbers. Further, investigations were made in literature and documents on the domestic and international trend of development of high-temperature superconducting flywheel systems, elucidating the details of the development. (NEDO)

1998 Annual Study Report. Research and development of power storage by high-temperature superconducting flywheels. Research and development of high-temperature superconducting materials; 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (koon chodendozai no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This R and D program is aimed at optimization of superconductors for improved levitation force of the superconducting magnetic bearings which support a 10 MWh power storage system by high-temperature superconducting flywheel (FW), to clarify possibility of sizing up the FW body and R and D themes for the commercialization. The processes are screened to simultaneously solve the conflicting targets of sizing up the sample of the Y-based bulk superconducting material and improved crystal orientation of the whole bearing, leading to selection of multi-seeding. The sample made on a trial basis improves levitation force by approximately 30%. It is considered that the OCMG-processed rare-earth-based superconducting material can generate very strong electromagnetic force, when combined with a permanent magnet. The Ag-doped Sm-based bulk material shows a reduced creep-caused loss of loading force, and a lower loss of Jc resulting from increased temperature than the Y-based one, decreasing AC loss and controlling temperature rise. The running characteristics and mechanical strength of the FW, and causes for temporal changes are investigated, in order to evaluate the superconducting material characteristics. (NEDO)

Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (system design/evaluation (comparative assessment/information collection)); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system sekkei, hyoka (hikaku kento, joho shushu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

For the purpose of evaluating the basic characteristics of high-temperature superconducting magnetic bearings (SBM), a system model is designed, experimentally manufactured and tested, which is embodied in the design/evaluation of a large-scale system, with an investigation carried out for the introduction of the system into an electrical power system. In this framework, an examination and research were conducted for the system design technology on which each component technology in the system structure can be applied consistently in the system. In the comparative assessment of various flywheel power storage systems, the specifications and achievements were compared in the component elements of the flywheel systems developed in Europe, America and Japan through the literature studies and the field survey, with examination performed towards the future development. As a result, it was found that, in America, bearings were all SMB's without control. Boeing's objective for the development is 10kWh or so in view of convenience for transportation and is prone to arrange it in numbers. Further, investigations were made in literature and documents on the domestic and international trend of development of high-temperature superconducting flywheel systems, elucidating the details of the development. (NEDO)

Project of the basic survey of cooperation for the heightening of energy efficiency in developing countries. Project for inviting engineers from developing countries to Japan (Malaysia); Hatten tojokoku energy shohi koritsuka kyoryoku kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Malaysia)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

For the purpose of plannably and effectively spreading the results of demonstrative researches on energy conservation and environmental technology in developing countries which were jointly made with Japan and Japan`s advanced energy conservation and environment technology, etc., the project invited engineers of developing countries to Japan, gave the intensive research instruction, made the required information exchange, and attempted improving R and D ability of the engineers and smoothening transfer/spread of the technology concerned. Malaysia has been advancing strongly the economic growth along `the 6th Malaysia Plan,` and aims, as a national target, at completing industrialization by 2020 and reaching the level of developed countries. However, the environment problem in Malaysia is worsening. In this invitation project, two-week training was given to 15 trainees, paying attention to the following three items: (1) introduction of technologies of energy conservation and environment in Japan, (2) actual field training at research institutes and corporations which have high-technology on energy conservation and environment, and (3) information exchanges with executive officials, scientists, and researchers in Japan. 6 figs.

Report on FY 1998 project for international energy utilization rationalization, etc. (Project of the analytical tool survey for making energy consumption effective in Asia); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the Asian region, for the purpose of grasping effects of both economic growth and effective energy consumption, an analytical tool added with a computational function was developed with the interindustrial relations table as database for the analysis of the present situation and the simulational analysis. In the analysis of the present situation, changes between the two time-points, 1985 and 1990, were analyzed using the developed energy consumption table and the CO2 emission table. The energy consumption amount is increasing with the growing economy. However, the energy unit consumption is decreasing in countries except Korea, the Philippines, Singapore and Malaysia. The trend is that the energy consumption is becoming effective and the CO2 emission amount is decreasing. As an example of simulating the introduction effect of energy saving technology, the simulation was conducted on the three: iron steel, paper/pulp, and cement in Indonesia. As a result, the decrease in energy consumption was shown in paper/pulp by 48%, in cement by 16%, and in iron/steel by 16%. The same was also indicated in CO2 emission. (NEDO)

Fiscal 1999 survey report on basic feasibility in implementing model project for efficient consumption of energy by fiber dyeing and processing plant in Indonesia; 1999 nendo Indonesia ni okeru senshoku kako kojo energy shohi koritsuka model jigyo kihonteki jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The basic feasibility of a model project was investigated for the purpose of introducing energy saving technology in dyeing and processing by the textile industry, which consumes a great deal of energy in Indonesia. This paper explains the result of fiscal 1999. A questionnaire survey was conducted on 40 companies having a continuous processing plant from spinning to finishing, while seven companies among them were visited for the survey on the status of energy consumption and conservation. Meantime, a survey was also made on the related policies and the state of their implementation in Indonesia as well as on the status of investment on equipment. As energy saving measures for the processing, proposals were made for energy saving in the washing process (exhaust-heat recovery system, monitoring system, and optimization of steam usage in drying process), for introduction of a heat pump system, and for reduced energy consumption in a jet dyeing machine. As energy conservation measures for utilities, reduced energy consumption of boilers was proposed, as was introduction of co-generation system. Essential for the dissemination of the measures are guidance, enlightenment and mentality reform for the entrepreneurs. Needed for the policy are the establishment of a core organization for energy conservation, plans, analyses, model projects, and introduction of an economic support system (e.g., low-interest loan). (NEDO)

Report on achievements in fiscal 1999 on international model project for energy consumption efficiency improvement. 'Model project to enhance boiler and turbine efficiency'; 1999 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokoku. Boira gasu tabin koritsu kojo moderu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to save energy, reduce electric power generation cost, and reduce CO2 exhaust in Indonesia, the Japanese energy saving technologies were transferred to the Muara-Karang Power Station in Indonesia as the object of the project. This paper reports the achievement in fiscal 1999. The target was set to reducing the power generation unit requirement (heat consumption ratio, kcal/kWh) by 1% by improving such constitutional devices as water condensers and air pre-heaters. Further improvements were planned by introducing the thermal efficiency control program. The subject fiscal year has performed data acquisition from the site surveys, investigations on related technologies, and detailed designs for site construction and effect identification. Also having been carried out based on the result of the detailed designs was partial fabrication of members and parts necessary for facility modification such as for small tubes for water condensers made of new materials. Furthermore, the Indonesian engineers were accepted for the purpose of transferring the thermal efficiency management methods, and the maintenance and control technologies for devices being the objects of the facility modification related to the boiler and turbine efficiency improvement. (NEDO)

Basic survey project of advanced efficiency of energy consumption in developing countries. Engineer invitation project from developing countries such as Vietnam, Philippines, China and Thailand; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Betonamu, Philippine, Chugoku, Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For contributing to the promotion of energy saving and environmental conservation, eighteen officers and engineers were invited to Japan during the period between January 14th and 23rd in 1997, from Vietnam, Philippines, China and Thailand. This report summarizes the invitation project for training conducted under a theme `Energy saving and environmental conservation.` Lectures were given concerning activities of global environmental conservation by NEDO, history and measures of overcoming the Yokkaichi pollution, outline of new energy, outline of energy saving, outline of basic environment law, outline of final industrial waste treatment facilities, and global environmental issues. Site training was conducted at Hekinan Thermal Power Station of Chubu Electric Power Co., Inc., Fujiwara Works of Onoda-Chichibu Cement Co., Ltd., and Yokkaichi Works of Kyowa Petroleum and Chemistry Co., Ltd. Questions and answers were exchanged. The new energy and energy saving were impressive, and were new concept for the trainees. This project was considered to be continued. The inspection of works was also well received, which was considered to be continued

Achievement report for fiscal 1998. Energy consumption efficiency improvement model business for developing nations (Demonstration research project on new cooling system in cement clinker production); Hatten tojokoku energy shohi koritsuka model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims at energy saving and CO2 emission reduction for a clinker cooling system (CCS), and a demonstration test was conducted at a demonstration cement plant in Indonesia. The plant started operation using the new CCS aiming for the enhancement of cooling and heat recovery efficiency. The actually achieved heat recovery efficiency attributable to the adoption of the new CCS was 60.8% against the target of 68%, this meaning an improvement of 8% over the value recorded prior to the new CCS adoption. As for increase in recovered heat due to heat recovery efficiency improvement of the CCS itself, it was 31kcal/kg-clinker. The heat reduction rate throughout the system thanks to the new CCS was 40kcal/kg-clinker. The kiln secondary air temperature increased for improved burner combustion performance for a rise of the clinker burning degree to 12kcal/kg in terms of calorie, and thus a reduction of 52kcal/kg-clinker in total was achieved. No mechanical trouble was reported with the new CCS. Investigations were conducted into cement supply/demand and technological trends in Indonesia, Vietnam, and China. Learnings from the investigation of German cement making technologies were fully utilized in the designing of the new system. (NEDO)

Report on achievements in fiscal 1996. International energy usage rationalization project (project to survey energy consumption efficiency improvement analyzing tools for Asia/data edition); 1996 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho shiryohen. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

This paper is a collection of data on surveys for energy consumption efficiency improvement, taking Japan, Korea, Indonesia, Thailand, and Philippines as the object countries. I. Industry related various value tables consist of the following: basic transaction table, throw-in coefficient table, final demand converter table, import coefficient table, added value coefficient table, inverse matrix coefficient table, sensitivity coefficient table, influence coefficient table, production inducing amount, production induction dependence, import inducing amount, import induction coefficient, import induction dependence, and inverse matrix coefficient table. II. Energy related various coefficient tables consist of the following: inherent unit quantity table, energy consumption table, CO2 table (1), CO2 table (2), unit requirement table, energy consumption induction table, energy consumption induction coefficient table, energy consumption induction dependence table, CO2 induction table (1), CO2 induction coefficient table (1), CO2 induction dependence table (1), CO2 induction table (2), CO2 induction coefficient table (2), and CO2 induction dependence table (2). Industries are classified into 34 kinds. III. The energy consumption table, CO2 table (1) and CO2 table (2) are shown as the simulation results for the four countries: Korea, Indonesia, Thailand, and Philippines. (NEDO)

Joint research report of Central Research Institute of Electric Power Industry and Japan Research Institute Ltd. Conceptual construction of Japanese type end-use model; Denryoku chuo kenkyusho Nihon Sogo Kenkyusho kyodo kenkyu hokokusho. Nippon gata end use model no gainen kochiku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The concept of Japanese type demand analysis model (end-use model) was constructed for the efficient management of electric power companies and efficient power utilization. Diffusion and use conditions of domestic air conditioners are considerably different depending on local life style and climate. In order to design demand measures considering combination of appliances in every market segment, demands in an end use level (end demand level, each appliance level) should be acquired. The basic structure of the model is composed of various exogenous variables such as weather data, price and ups and downs trend of customers, and various appliance data such as size, efficiency and energy consumption rate, and various customer data such as possession rate of appliances and number of customers. The final energy demand is estimated by integrating the above variables. By systematizing the stored data of precise actual load conditions, construction of DSM (demand side management) strategy becomes possible by using computer tools. 8 refs., 15 figs., 13 tabs.

FY 2000 Report on technological trend surveys. Surveys regarding construction of the co-production techniques for substance and electric power; 2000 nendo gijutsu doko nado chosa hokokusho. Busshitsu to denryoku heisan ni yoru co-production gijutsu no kochiku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project is aimed at surveys on the elementary and peripheral techniques necessary to construct the systems, with the objective to draw the conceptual designs of the total system for co-production of a substance and electric power. In a general reaction process, substances are produced under an advantageous condition that is dependent on reaction rate and equilibrium, where most of the energy is dissipated in the form of sensible and latent heat without being used for the chemical reaction. The co-production system under consideration uses high temperature of 500 degrees C or higher exhausted from a power station or industrial unit to produce macromolecules or synthesis gases, wherein the exothermic reaction increases temperature of the heat source, which is recovered in the form of steam for driving the steam turbine to produce electric power. On the other hand, low-temperature waste heat of around 150 degrees C is converted into a liquid fuel or other value-added products by the liquid phase pressurized system. The elementary techniques to construct these processes are surveyed, and the thermal processes are analyzed. The investigated items include substance production processes, electric power production processes and total systems. (NEDO)

Achievement report for fiscal 1999. Joint verification research on use for power generation of Omani superhigh-viscosity crude oil remaining unexploited; 1999 nendo Oman koku ni okeru miriyo chokonensei gen'yu no denryoku riyo ni kansuru kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A Mukhaizna oil field remains to be exploited in Oman, with an estimated reserve of 2.4-billion barrels of very heavy oil with an API (American Petroleum Institute) specific gravity of 15.3. The viscosity of the oil is so high as to be over 100-thousand cP (at 15 degrees C). The extremely high viscosity causes its exploitable rate to be so low as 3%, and makes shipment by pipeline quite difficult. In this survey, a method using water emulsion is proposed for viscosity reduction, which aims to reduce the Mukhaizna crude oil viscosity to 200mm2/s or less. In an experiment using the water emulsion method, oil is mixed with water at a rate of 72 to 28 in a shearing mixer for the production of a water emulsion of crude oil. It is found that a certain degree of stability is acquired using a surface active agent available on the market. Using this emulsion method, the crude oil is converted into a power generator fuel with a heating value of 6,775kcal/kg. The crude oil-turned product is a fine fuel superior to Orimulsion which is a fuel of the same type in terms of viscosity, amount of ash, and vanadium concentration. (NEDO)

Report on the results of efforts for fiscal 1997. Development of technologies for creating high-quality crystal materials for low-loss power control devices; 1997 nendo seika hokokusho. Teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Basic technologies are developed for the manufacture of high-quality crystal materials large in diameter and homogeneous in property which will allow power control semiconductor devices to grow more sophisticated in function and to be lower in the loss they suffer. Physical properties of molten semiconductor and the like are measured accurately, which include surface tension, density, viscosity, electric conductivity, thermal conductivity, emissivity, diffusion coefficient, vapor pressure, heat capacity, contact angle, and solid solution equilibrium distribution coefficient. In computer-aided simulation, as in the previous year, simulation codes are developed for the analysis of flow, temperature distribution, and diffusion behavior in the gas phase; simulation codes are developed for the analysis of 3D unsteady thermal flows in the melt; and a main program is developed which governs experimental calculations. As for experiments in model Czochralski crucibles, small crucible are used in which experiments are conducted in the temperature range of normal to 200degC for the acquisition of experimental data for verification. Measured by use of the model crucibles are the temperature distribution in the bath, the surface flow speeds, and the flows inside the melt. 140 refs., 153 figs., 10 tabs.

TMN-based network management systems for utility telecommunication network. Pt. 4. Method of estimation of processing time for a management function; ATM ni motozuku denryoku tsushinmo no un`yo kanri system. 4. Kanri kino tani no shori jikan suitei hoho

Energy Technology Data Exchange (ETDEWEB)

Yusa, H.; Otani, T.

1998-05-01

A method of estimation of processing time for a management function is proposed to test system performance. This method utilizes characteristics of message passing between managed objects to recognize all over the systems. Estimation of processing time is proceeded with following steps. (1) analysis of message flow: with design information, message patterns are set and the number of messages to be sended and received are counted. (2) measuring processing time of each message type: we developed programs to measure processing time of sending and receiving messages. Using this programs, message processing time for each message type is measured. (3) calculating total system processing time: managing system processing time and managed system processing time are calculated. Total system processing time is derived from those. This paper also shows the applying proposed method to SDH fault detection function, which have two different processes: all event process, event and log process. This resulted in 2:1 processing time on a case of fiber cut off for managing two SDH equipments. (author)

Report on a survey in fiscal 1999. Survey on electric power systems for reducing CO2 emission (an approach to scenario analyses); 1999 nendo CO{sub 2} sakugen no tame no denryoku system ni kansuru chosa hokokusho. Scenario kaiseki no approach

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of this survey is to extract by using scenario analyses the unreliable factors having great influence on change in the Japanese power supply configurations, and verify how the unreliability of these factors would affect the future structures and what the resultant ratio of the power mixes would be in the future. The survey is also intended to verify, through a series of work of calculating how much CO2 emission quantity would be changed in the stage of the year 2012 in each power supply configuration, whether or not the approach by using the scenario analyses will provide information sufficiently reasonable to judge policies to realize reduction in CO2 emission around the electric power business. Although including many hypotheses and vagueness, the trial calculation subjected to each scenario prepared presently suggested that it is not possible to accomplish the target of reducing 9% from the 1990 emission level only by the single efforts inside Japan. This result shows the same contents and directionality that are shown by the results of a large number of surveys. However, the result has created a common recognition among the participants that {sup t}here is a possibility that some kind of effective countermeasures could be discovered{sup .} (NEDO)

Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

Fiscal 1975 Sunshine Project research report. Research on safety technology for hydrogen (Research on safety technology for hydrogen in distribution and consumption processes); 1975 nendo suiso no hoan gijutsu no kenkyu seika hokokusho. Suiso no ryutsu, shohi process ni okeru hoan gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-25

The experiment result on discharge and diffusion of hydrogen gas from underground buried conduits and compressed hydrogen gas vessels, and the hydrodynamic study result on gas discharge are as follows. The discharge experiment from underground buried conduits showed that the amount of gas leakage increased with a discharge duration linearly, and increased with a pinhole diameter at a rate more than a cross section ratio. Its underground diffusivity is large, and hydrogen gas advances as spherical wave uniformly within a certain discharge velocity. Gas leakage on the ground surface is affected by not buoyancy but wind (air flow) strongly. The discharge experiment from compressed hydrogen gas vessels showed that the diffusion concentration profile of discharged gas can be explained by conventional diffusion equation. Variation in gas pressure in vessels due to gas discharge, and durations until the end of discharge agree with hydrodynamic data on the whole. Thrust and change in gas temperature due to gas discharge can be estimated theoretically by the same manner. (NEDO)

Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

Report of fiscal 1997 R and D result on high temperature superconducting flywheel power storage. R and D of manufacture of superconducting magnetic bearing; 1997 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu seika hokokusho. Chodendo denjiki jikuuke no seisaku no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Element technologies were developed for the manufacture of superconducting magnetic bearing (SMB) with the purpose of putting to practical use a 10 MWh class high-temperature superconducting flywheel power storage system. This paper explains the fiscal 1997 results. A {phi} 180 radial type SMB was designed and fabricated that satisfied the rotational strength at 17,200 rpm for a medium-sized model for measuring characteristics. Compared with the bearing made in the preceding year, improvements in the bearing dynamics were contrived such as flux creep, load capacity and rotational loss, with the maximum flux density improved by 30%; however, only a few percent improvement was attained in field uniformity. An SMB characteristics measuring and testing machine was built, with the characteristics measured. It was confirmed that the rotational loss of a control type magnetic bearing and the intrinsic performance of the testing machine were unchanged regardless of the operation/non-operation of the radial type SMB. The characteristics of the {phi} 180 axial bearing were measured by a stationary type bearing constant testing machine made in 1995, which provided a load capacity characteristics curve with the initially set gap as a parameter as well as a minor loop curve and a load capacity. Also obtained were the maximum average bearing pressure and the maximum load capacity. (NEDO)

Achievement report for fiscal 1999. Joint verification research on use for power generation of Omani superhigh-viscosity crude oil remaining unexploited; 1999 nendo Oman koku ni okeru miriyo chokonensei gen'yu no denryoku riyo ni kansuru kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A Mukhaizna oil field remains to be exploited in Oman, with an estimated reserve of 2.4-billion barrels of very heavy oil with an API (American Petroleum Institute) specific gravity of 15.3. The viscosity of the oil is so high as to be over 100-thousand cP (at 15 degrees C). The extremely high viscosity causes its exploitable rate to be so low as 3%, and makes shipment by pipeline quite difficult. In this survey, a method using water emulsion is proposed for viscosity reduction, which aims to reduce the Mukhaizna crude oil viscosity to 200mm2/s or less. In an experiment using the water emulsion method, oil is mixed with water at a rate of 72 to 28 in a shearing mixer for the production of a water emulsion of crude oil. It is found that a certain degree of stability is acquired using a surface active agent available on the market. Using this emulsion method, the crude oil is converted into a power generator fuel with a heating value of 6,775kcal/kg. The crude oil-turned product is a fine fuel superior to Orimulsion which is a fuel of the same type in terms of viscosity, amount of ash, and vanadium concentration. (NEDO)

Report of fiscal 1997 R and D result on high temperature superconducting flywheel power storage. System design and evaluation (comparative study and information gathering); 1997 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu seika hokokusho. System sekkei hyoka (hikaku kento, joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Information gathering and comparative study were conducted for the purpose of putting to practical use a 10 MWh class high temperature superconducting flywheel power storage system. This paper explains the fiscal 1977 results. On various methods conceivable as a flywheel system, characteristics were extracted in such points as structure, shape, axial support system, generator motor, and protective system, and compared with the method being developed in the present project. Test items methods, etc., were studied for a small model system (0.5 kWh, {phi} 400 mm, 30,000 rpm) for the purpose of clarifying problems and ways in approaching a large system (10 MWh class) through various tests of the small one. The main test items were a free-run test, steady state rotation test and a heat-run test, and the main points to evaluate were oscillation characteristics and the control performance of AMB, flux creep and loss, for example. Investigation was conducted of a dummy flywheel experimental equipment and a highly efficient power converter with the object of contributing to the development of a flywheel equipment for daily load leveling. The research members visited seven major research organizations in Europe and gathered information. (NEDO)

Current status of and problems in ice heat storage systems contributing to improving load rates. Strengthening works intended for leveling the electric power load; Fukaritsu kaizen ni kokensuru kori chikunetsu system no genjo to kadai. Denryoku fuka heikinka ni muketa torikumi no kyoka

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. [Agency of Natural Resources and Energy, Tokyo (Japan)

1998-02-01

This paper introduces improvement in annual load rate in power supply in Japan, and the measures to proliferate and expand the use of ice heat storage systems. The annual load rate in power supply has dropped to about 55% today from the level of about 70% in 1965. This has been caused by the following reasons: the maximum power demand having become sharper in summer due to rapid increase in demand for air conditioning for room cooling, increase in weight of business operation department associated with progress of service economy, and change in the industrial structure from the material type industry to the processing and assembling type industry in the industrial department. In order to achieve load shift in the room cooling demand, which accounts largely for consumer demand during the peak time in summer, and is the main cause for reduced load rate, it is important that a heat storage type air conditioning system and a gas room cooling system be used more widely. The heat storage air conditioning and gas room cooling systems have a bottleneck in their proliferation that their facility cost is more expensive than existing air conditioning systems of non-heat regeneration type. It is necessary to review legal institutions and electric power charge systems for the purpose of proliferation and expanded use of the heat regeneration air conditioning and gas room cooling systems. 2 figs.

'Development and introduction of ice water conveyance system and verification of low temperature blast system' for leveling off electric power load; Denryoku fuka heijunka wo misueta 'hyosui hanso hoshiki no kaihatsu donyu to teion sofu hoshiki no kensho'

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, T. [Nikken Sekkei Ltd., Osaka (Japan)

1999-11-05

From the view point of the earth environment protection, energy-saving in the field of building air-conditioning has become increasingly important. On the other hand, the utilization of nighttime electric power is needed to ease the electric power supply and demand problem, and in this connection, a wider introduction of the ice heat storage system is recommended as one of the means to cope with such a problem. However, the ice heat storage system also has problems to be solved such as energy savability, and economy. Under such circumstances, various technical research and development efforts as well as evaluation thereof have been made centering around the 'technical development of the ice water conveyance system' and the 'evaluation of the low temperature blast system' for energy-saving, facility cost reduction and electric power load leveling off, and as a matter of fact these systems have been installed in actual buildings with useful results. (author)

Fiscal 2000 cooperative basic project for investigation of efficiency in international energy consumption. Project for inviting researchers from developing countries (Indonesia, Philippines, Thailand and Vietnam); 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Hatten tojokoku kenkyusha shohei jigyo (Indonesia, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

As a part of international cooperation concerning global environmental issues, ICETT (International Center for Environmental Technology Transfer) invited administrative officers, engineers, etc., of developing countries, for the purpose of encouraging experts connected with energy conservation and environmental protection technologies, providing training on the administrative technique, antipollution technologies, energy conservation technologies, etc. The training period was from December 3 to 21, 2000, with 12 participants attended, three each from four countries, Indonesia, Philippines, Thailand and Vietnam. The contents of the technological instruction were such that cases in Japan concerning energy conservation and environmental protection were introduced generally from the administrative measures to the technological countermeasures, as were done conventionally. In the area of the environmental protection, lectures and tours on wastewater treatment were added as industrial wastewater control measures. In the subject of new energy, micro hydraulic power was added which is in progress for example in Indonesia under an aid from Japan. In the energy conservation technology, a supplementary lecture was given on the concept and methodology of an environment-protective type production technology, with emphasis placed on the energy conservation and environmental protection in manufacturing plants and production processes. (NEDO)

Fiscal 2000 survey report. Survey of preparation of energy consumption index for Asian region and of prediction of amount of new energy to be introduced; 2000 nendo Asia chiiki no energy shohi koritsu shihyo no sakusei to shin energy donyuryo no yosoku ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For Japan whose domestic reduction of greenhouse gas emissions is but limited, an approach to the problem with emission tradings and CDMs (clean development mechanisms) taken into consideration is necessary, and improvement on energy consumption in the Asian region as a whole is indispensable. From this viewpoint, countries in Asia who might be candidate importers of Japan's technical assistance were selected, and their energy conservation potential and farming village electrification potential were investigated. Covered by the survey were China, Philippines, Thailand, Vietnam, Malaysia, Indonesia, and India. Investigations were conducted into the fields named below, and the results were grouped into the same. The fields were (1) economic growth and energy supply/demand in the Asian region, (2) energy conservation in the Asian region, (3) electrification of farm villages in the Asian region, (4) cost analysis for farm village electrification in the Asian region, and (5) simulation of new energy introduction. The results show that there is a great difference between the seven countries in all the five fields. (NEDO)

Project for the basic survey of enhancing energy consumption efficiency in developing countries. Summary of the Conference on the Policies and Measures of Climate Change Mitigation; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Kiko hendo kanwasaku no seisaku to sochi ni kansuru kokusai kaigi hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The Conference on the Policies and Measures of Climate Change Mitigation was held in Tokyo on January 28, 1997, with participation in the conference from governments, research institutes, industrial circles, NGO, etc. of ten countries including Japan. In the session `technology transfer,` presentations were made on `the current status of the technology transfer, and the expectation and requests` by Australia and Japan which provide technology and by China which receives technology. As a whole, every country recognized importance of technology transfer of both hardware and software, private sectors` taking leadership, the use of international organizations dealing with fund supply and credit guarantee. In the session `tradable permits/quotas,` Dr. A. Haspel, U.S. Department of Energy reported the structure and effect of U.S. tradable emission permits on sulfur dioxide from thermal power plants, and proposed tradable emission permits against greenhouse effect gas. The proposal needs to be further studied and discussed, and it was regarded as too early to include the proposal in the protocol to be conducted at COP3

Report of fiscal 1997 R and D result on high temperature superconducting flywheel power storage. R and D of characteristic analysis of superconducting magnetic bearing; 1997 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu seika hokokusho. chodendo jiki jikuuke no tokusei kaiseki no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

This paper explains fiscal 1997 results of the development of technologies for characteristic analysis of superconducting magnetic bearings (SMB), the development aimed at putting a 10 MWh high temperature superconducting flywheel power storage system to practical use. Following fiscal 1996, calculation programs were prepared for a load capacity and bearing constant (spring constant, damping constant) on an axial type SMB, with validity of the program examined through comparison with experimental values. A finite element method was applied to a complex magnetic field by a magnet arrangement devised for the purpose of improving load capacity, dividing a superconductor into divided sections so that the effect of a complex magnetic field distribution could be reflected, determining the magnetization generating in each divided section by using a two-dimensional Bean model, and developing a method for calculating load capacity of each divided section by a magnetic moment method. A program was completed for calculating the load capacity and bearing constant of the entire bearing in the axial type SMB. The calculated value of the load capacity and the bearing constant showed a superior agreement with the experimental value. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

Studies of an application of mobile communication system to the private telecommunication network. Part 2. Trend of mobile communication systems and application to power utility; Idotai tsushin system no denryoku tsushinmo eno tekiyo. 2. Idotai tsushin system no genjo to denki jigyo eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Iwasaki, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-06-01

This paper presents future prospects on development of different mobile communication systems operated by public communications operators, and discusses their application to power utilities. For automobile and cellular telephones, discussions are being made on the code division multiple access (CDMA) system which multiplexes and transmits information by using tally codes. Influence of noise decreases, and so does the need of retransmission due to code errors. Higher speed transmission than conventional systems may be expected. The system can be utilized for transmitting still images, such as for status of construction being carried out by power utility companies. For PHS, a discussion will start on 32 to 64-kbps transmission in fiscal 1997. By using the system together with an image compression technology, the system may be expected of utilization as a moving image transmission method for supporting site works by utility companies. The low and medium orbit satellite communications whose use is scheduled to start shortly can be utilized as construction and emergency disaster communication networks for mountainous areas and islands. Movements around the frequency band utilization and communication systems of IMT-2000 are becoming more complex. The Japanese proposal plans transmission of moving images, whereas more diverse utilization can be expected, such as for voice, data and images, in areas where no ground communication facilities are available for electric power operations. 16 refs., 4 figs., 3 tabs.

Basic research on energy conservation in developing countries. Basic research on promotion of activities implemented jointly (AIJ) (research on possibility of AIJ in developing countries); Hatten tojokoku energy shohi koritsuka kiso chosanado jigyo kyodo jisshi suishin kiso chosa. Hatten tojokoku ni okeru kyodo jisshi katsudo no kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The activities implemented jointly (AIJ) is expected as global measures to reduce greenhouse gas (such as CO2) emission. In this report, the possibility of AIJ projects in developing countries was researched. The United Nations Framework Convention on Climate Change was signed by 155 countries in 1992. This convention parties approved AIJ projects for measures against global warming. The 1st Conference of the Parties (COPI) held in 1995 approved the pilot phase of AIJ by voluntary workers jointly with developing countries until the end of this century. The trend, level and future plan of energy conservation technologies were researched and analyzed for steelmaking, cement and electric power supply industries in both the Philippine and Thailand. The possibility of AIJ projects was studied by selecting several Japanese energy conservation technologies transferable to both countries. The same research was also carried out for forest as carbon absorption source. 5 refs., 23 figs., 58 tabs.

Model project for enhancing energy consumption efficiency in developing countries. Report on changes of energy conservation technology and environmental protection technology in the chemical industry of Japan; Hatten tojokoku energy shohi koritsuka model jigyo. Nippon kagaku kogyo ni okeru sho energy gijutsu to kankyo taisaku gijutsu no hensen hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of contributing to the economic growth and the global environmental protection in the Asian area, an investigation was carried out into energy conservation technology and environmental protection technology in the chemical industry of Japan. Measures for energy conservation are shifting from those which do not cost so much such as reduction in excess air rate of the heating furnace, and reduction in reflux ratio of the distillation tower to those with equipment investment such as waste heat recovery of the heating furnace and waste heat recovery of the distillation tower. In the 1980s, the utilization of low temperature waste heat by absorption type refrigerator and heat pump was promoted and the energy utilization efficiency by computer control was enhanced. Concerning environmental measures, the following were carried out: installation of the flue gas desulfurization device and reconstruction of high-rise stack, reduction of NOx by combustion control, smoke/dust disposal of electrostatic precipitator, combustion of hydrocarbon causing photochemical oxidant, catalytic oxidation, condensation, treatment by activated carbon, activated sludge treatment for BOD/COD, diaphragm process for dimethylmercury, ion exchange resin process, etc. 21 refs., 29 figs., 27 tabs.

FY 1974 report on the results of the Sunshine Project. Study of the hydrogen safety technology (Study of the hydrogen safety technology in the distribution/consumption process); 1974 nendo suiso no hoan gijutsu no kenkyu seika hokokusho. Suiso no ryutsu shohi process ni okeru hoan gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-25

To put it forcibly, the gas leakage problem should be solved to prevent disaster accidents caused by high pressure gas. From this point of view, the R and D of the safety technology were conducted for the process of hydrogen distribution/consumption. The literature collected was studied, and the present situation was again recognized of the hydrogen gas industrial circle in Japan. At the same time, hydrogen physical properties and the peculiar dangers derived therefrom were comprehensively arranged. Examples of accidents tell realistically how dangerous hydrogen is, and give suggestions for treating hydrogen safely. We can see a lot of examples of how to treat liquid hydrogen in the U.S. It seems that there are no effective methods to detect the leakage of hydrogen, and methods to meet each case are required. To sum up, the research results show how much safety of the distribution/consumption process is secured under the present safety technology and legal regulation. At the same time, those also indicate how much the safety can be enhanced technically in the future. (NEDO)

FY 2000 report on the results of the R and D of fundamental technologies of superconductivity applications. Development of technology to process low consumption power ultra high speed signals; 2000 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

In relation to the project on the R and D of fundamental technologies of superconductivity applications, the FY 2000 results of the design/fabrication of superconducting circuits were summarized. As to the development of technology to design superconducting circuits, an increase in circuit scale was tried targeting AD converter use modulator and decimation filter. As a result, operation was confirmed in element circuits of flux quantum multiplier circuit, feed back driver, DC isolator, etc. Concerning the development of technology for standard junction and integration, RHEED observations on the thin film surface before/after etching and YBa{sub 2}Cu{sub 3}O{sub 7-x} re-deposition were tried to be made, and the potentiality as monitoring technology was indicated. With respect to the fabrication of small scale circuits for demonstration, the design/trial fabrication were made of the basic pattern of SFQ circuit elements such as DC-SFQ, T-FF and SQUID for inductance rating. In regard to the development of technology to measure characteristics of superconducting circuits, a system was fabricated for processing and measuring output signals from {sigma}-{delta} modulators by semiconductor circuits, and it made the evaluation of AD converter performance possible. (NEDO)

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

Development of reader for the demand data from compound demand meter for power supply/demand (CDM). Development of recommended tools for load leveling in existing works; Denryoku jukyuyo fukugo keiki kara no demand data yomitori sochi no kaihatsu. Kisetsu kojo no fuka heijunka suisho tool no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakamoto, S. [Kansai Electric Power Co. Inc., Osaka (Japan)

1997-10-10

Kansai Electric Power has developed a system which reads the demand data for 30min. stored in the compound demand meter for power supply/demand (CDM), and prints the load curves. It is for customers of high-voltage power of less than 500kW, where load management is less extensive than that in larger users, for initial consulting on improvement of load factor (recommendation of heat storage contracts). It is to be installed on the spot to display the load curves, to allow the expert visiting the site to issue initial proposals immediately. It displays `daily demands by time zone` instead of `monthly power consumption` previously provided, and makes the graph of demands by time zone. It is designed to be compact, light, and easily and safely handled. The field test results indicate that the system can be sufficiently practical with the major performance items. 4 figs., 1 tab.

Time path of marginal cost for measures against global warming toward the greenhouse gas concentration target. Analytic solution and case study of the electric power sector; Onshitsu koka gas nodo mokuhyoka deno ondanka taisaku genkai hiyo no jikan keiro. Kaisekikai to denryoku bumon no case study

Energy Technology Data Exchange (ETDEWEB)

Nagano, K.; Sugiyama, H.; Takahashi, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-01-30

The United Nations Framework Convention on Climate Change is studied from the viewpoint of implementing costs. As far as the global warming issue is concerned, the factor to affect the environment is not the emitted volume but the concentration in the air. The ultimate target is the stabilization of greenhouse gas concentration at a level not to impose serious artificial damage on the ecosystem. Accordingly, various time paths are considered, including one in which much emission is allowed at the beginning and suppression is enforced acceleratedly in the later stage. In this study, a path demanding but the minimal cost in the period up to the target time point is discussed, using as the tool the marginal cost for measure implementation. In a reasonable emission control strategy, the emission control marginal cost follows a time path that is dependent upon an increase function to be determined by the discount rate and survival rate (time constant) in the atmosphere. In the industrial branch, instead of imposing short-term and rigid emission volume control limits, a longer-term target may be set for reduction in the loads responsible for concentration acceleration, concrete emission controls under the given conditions may be implemented at the discretion of the implementing organizations, and reduction in cost may be realized by time distribution with the environmental impacts kept at approximately equal levels. 5 refs., 2 figs., 3 tabs.

Report on achievements in fiscal 1999. Research and development of electric power storage using high-temperature super-conductive flywheels (research and development on manufacture of super-conductive magnetic bearings); 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. Chodendo jiki jikuuke no seisaku no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Introduction of electric power storage equipment is sought, which will be discretely installed in power distribution substations. Therefore, elementary technologies were researched on 'manufacture of super-conductive magnetic bearings' intended for practical application of an electric power storage system of 10-MWh class using high-temperature super-conductive flywheels. Research and development has been performed on different kinds of super-conductive magnetic bearings which combine high-temperature super-conductive materials with permanent magnets. In order to measure the characteristics of the super-conductive magnetic bearings, measurements were executed on rotation loss, loading power and bearing constants. In the measurement of the rotation loss, a {phi} 180 axial type super-conductive magnetic bearing using an Sm-based superconductor ({phi} 180AxSMB2) was given various kinds of tests by using a rotation loss measuring and testing machine. The results were compared with those for the {phi} 180AxSMB1 using the YBCO-based superconductor and other SMBs. In the measurements for the other items, various items were measured on dynamic rotation properties of the {phi} 180AxSMB and {phi} 180RaSMB by using a static bearing constant testing machine. In discussing the loading power characteristics, the dynamic rotation properties of the {phi} 180RaSMB were measured, and the loading power characteristics were discussed on super-conductive magnetic bearings for medium size models and super-conductive magnetic bearings for large system FS. (NEDO)

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries and programs of international conferences including IPCC. Report on CDM workshop; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / IPCC nado kokusai kaigi jigyo (CDM workshop hokokusho) 1998 nendo jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It is decided in the COP4 that the concrete schemes for the (Kyoto Mechanism) should be boiled down towards the end of 2000. Of the many outstanding issues concerned, those related to the clean development mechanism (CDM) involve a number of problems awaiting solution. In particular, setting the baselines for amounts of the greenhouse effect gas emissions in projects not existing, which are essential for identifying reduced amounts of emissions (or credits), poses serious difficulty because of wide arbitrariness involved in the methodology. Therefore, (standardization) of the procedures is demanded for the accurate identification. In actuality, however, no methodology has been established as to what methods will be possibly applicable to widely diversified types of projects. This workshop, therefore, has focused the discussions on the (baseline problems), expecting to serve as a trigger for the future directions by presenting international researches and promoting the discussions thereon to deepen recognition of these problems, where the AIJ experiences have served as one of the bases. (NEDO)

FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

Development of customer information network system. Part 3. Development of power controller (customer side equipment) for advanced customer service and remote processing of conventional customer service; Juyoka joho network no kaihatsu. 3. Juyoka taio gyomu no enkaku shori to aratana juyoka service no tame no denryoku controller no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yoshimitsu, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-06-01

To offer remote processing of the conventional customer service and advanced customer service using information network, customer side equipment, power controller, was manufactured as a trial. For inspecting the power meter by remote processing, watt-hour meter placed outside was moved into house, to integrate an indoor distribution board consisting of a breaker for contract, earth leakage breaker and branch breaker by adding functions of communication, equipment monitoring and control and functions of display and operation. When detecting fault, installed CPU (central processing unit) or DSP (digital signal processor) stops its operation and each breaker keeps its state as before the fault. Thus, there is no problem for power supply. This system has a battery to maintain and operate at least the display function in the case of outage. Advanced customer service functions could be added without a large cost. To increase understanding of customers concerning electric power saving and electric power itself, consuming electric energy and current are displayed at each branch. Outage of the whole house can be avoided by the rapid detection and removal of the earth leakage branch line. 14 refs., 14 figs., 3 tabs.

FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries / invitation of engineer trainees from developing countries (Indonesia, the Philippines, Vietnam and Myanmar); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / hatten tojokoku gijutsusha shohei jigyo 1998 nendo chosa hokokusho (Indonesia, Philippines, Vietnam, Myanmar)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

NEDO is positively implementing the training programs, in view of importance of training experts on (energy-saving and environmental conservation technologies), by inviting administrators and engineers from developing countries to educate them with Japan's pollution preventive techniques, administration procedures, energy-saving measures, and so on. In FY 1998, NEDO commissioned the International Center for Environment Technology Transfer to train administrators and engineers from Indonesia, the Philippines, Vietnam and Myanmar. This paper describes the proposals, based on the collected answers of the trainees to the questionnaires. The trainees were interested in all themes. About 40% of the trainees considered that the training period was short. Some trainees hoped the training course was held in summer. Difference in industrialization is reflected in difference in recognition and urgency of the environmental problems. Training was conducted by English and Vietnamese, but could be done without translators of Vietnamese. Preparation for the invitation needs a lot of works, and the course should be explained more thoroughly beforehand. It is regrettable that one trainee from Indonesia was late for the course. (NEDO)

FY 1998 annual summary report on project for international energy consumption rationalization. Survey on analysis tool for improving efficiency of Asian energy consumption (data book 2 for 1985); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 2 1985 nen data)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The data book is compiled, based on common industrial classifications, as the tool for analyzing, e.g., the mutual ripple effects of economic growth and increased efficiency of energy consumption throughout the Asia-Pacific region. This book summarizes the industrial-related and energy-related tables for 8 Asian countries and Japan. The book II is for the 1985 data (1987 data for China), comparing with the book I for the 1990 data. The industry-related tables are composed of the tables for transaction bases, input coefficients, final demand converters, importation coefficients, inverse matrices, sensitivity/influence coefficients, production inducement levels, production inducement coefficients, degrees of dependence on production inducement, importation inducement levels, importation inducement coefficients, and degrees of dependence on importation inducement. Energy-related tables are composed of the tables for, e.g., energy input, energy consumption, emissions, and CO2 emissions. (NEDO)

Fiscal 2000 international energy use rationalization measures project. International energy consumption efficiency improvement technology diffusion project - Green helmet project (Thailand: Report on heating furnace energy conservation seminar); 2000 nendo. Kokusai energy shiyo gorika to taisaku jigyo, Kokusai energy shohi koritsuka to gijutsu fukyu jigyo, Green helmet jigyo (Thai : kanetsuro shoenergy seminar hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The above-named seminar was held in Bangkok, Thailand, on January 30, 2001, and covered three kinds of industries of ceramics, glass, and aluminum. Approximately 200 people attended the meeting, consisting of NEDO (New Energy and Industrial Technology Development Organization)-affiliated people and 16 lecturers from Japan, and Thai participants. The seminar comprised a 'keynote address' and 'lectures on engineering' that aimed at the three industries as a whole, and 'lectures on engineering' and 'cases and activities for energy conservation' that aimed, respectively, at the three industries. Lectures were delivered on operating technologies which were already in practical use and on state-of-the-art technologies. The keynote address, entitled 'Global warming prevention and industrial furnaces,' covered the results of the 'High-performance industrial furnace field test project.' The lectures on engineering dealt with the 'instrumentation control system' and 'heat insulation technology' which were basic technologies for energy conservation and 'diagnosis technology and practice' which aimed at the enhancement of energy conservation after the start of operation. Questions and answers were earnestly exchanged. (NEDO)

Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

Report on projects of the basic survey of effective energy consumption in developing countries and the invitation of engineers of developing countries to Japan (Vietnam, the Philippine, Indonesia and Thailand) in FY 1997; 1997 nendo chosa hokokusho Hatten tojokoku energy shohi koritsuka kiso chosa to jigyo hatten tojokoku gijutsusha shohei jigyo (Vietnam, Philippines, Indonesia Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Based on the significance of technological training for energy saving and environmental protection, NEDO has invited administrators and engineers of four countries in Southeast Asia. Pollution prevention technology, administrative methods and energy saving measures in Japan were lectured in the International Center for Environmental Technology Transfer. The training curriculum included (1) basic law of environment and local administration from the viewpoint of criminal law concerning history of air pollution problems and countermeasures in Yokkaichi petroleum industrial complex, (2) prospect of new energy technology development in Japan relating to the energy saving law, (3) energy saving measures, air/exhaust gas/dust treatment for environmental protection, and actual waste treatment measures by typical individual industries, and (4) significance of common management technology for individual treatment measures. Policies of energy saving and environmental protection and technology information in Japan which can be transferred were provided to two administrators of energy saving in the industry sector of Management of Science, Technology and Environment of Vietnam. 12 figs.

Survey report for fiscal 1998. International project for rationalizing energy use (a project for investigating analyzing a tool to improve energy consumption efficiency in Asia) (Data collection 1 (Year 1990 data)); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 1 1990 nen data)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to identify quantitatively the mutually influencing effect of economical development and energy consumption efficiency improvement in the entire Asia-Pacific region, a data collection was prepared according to the common industry classification as a tool to analyze energy consumption improvement in Asia. This data collection summarizes the industry relation tables and the energy relation tables available in eight Asian countries (Korea, Indonesia, Thailand, Philippines, China, Taiwan, Singapore and Malaysia) and Japan. Both kinds of the tables are unified in conception among the nations, hence comparable. The industry relation table consists of a basic transaction table, a charged coefficient table, a final demand converter table, an import coefficient table, a reverse matrix table, a sensitivity coefficient able, an influence force coefficient table, a production inducing amount table, a production inducing coefficient table, a production induction dependence table, an import inducing amount table, an import induction coefficient table, and an import induction dependence table. The energy table consists of an energy input table, an energy consumption table, and an emission table. (NEDO)

Report for fiscal 1999 on the international and fundamental cooperation project for energy consumption efficiency improvement and the international conference project such as IPCC. The meetings of IPCC specialists and IPCC symposiums; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo. IPCC senmonka kaigo oyobi IPCC symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

This paper reports the meetings of specialists and the symposiums by the inter-governmental panels for climate change (IPCC) in fiscal 1999. Three working groups were established for evaluation on climate change from scientific aspects, evaluation on effects and countermeasures from socio-economic aspects, and evaluation on mitigation measures from socio-economic aspects. The working groups have started preparing the third evaluation reports. Common problems are handled in a unified framework as the traversable problems. Specialist meetings are held for several important themes. Especially for the cost problems, preparation of a guidance paper has started, that include the costs and benefits by territories and departments. The themes for the specialist meetings include: cost problems related to effects and countermeasures for climate change and mitigation measures; the IPCC activities for the cost evaluation in the past and an outline of the traversable problems; problems in effects, applicable measures, and mitigation measures; and unification of the cost evaluations. The themes for the symposiums are the frontier line of the climate change problems, and include the outline of IPCC, the current status and issues in the working groups and the special reports for each group. (NEDO)

Fiscal 1999 research result report on energy and environment technology demonstration research support project (International joint demonstration research project). Japan- Russia joint demonstration research on large-capacity long- distant DC power transmission technology; 1999 nendo daiyoryo denryoku no chokyori chokuryu soden gijutsu ni kansuru Russia kenkyu kikan tono kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Under the assumption of a large-capacity DC power transmission model project in the Far East and Siberia districts, technical study was made on the basic design of the project, considering selection of concrete power generation and consumption sites and power transmission routes, power transmission/transformation equipment, cables, and environmental impact. Study was also made on its applicability to similar projects in Japan. The model project aims at integration of Eastern Integrated Power System in the Far East and Russian Unified Power System, and development of abundant undeveloped hydraulic and tidal power generation in the Far East. The study result showed that (1) construction of the high-voltage DC power transmission (HVDC) system of model project class voltage and capacity in Eastern Siberia is possible technically enough, (2) the total construction cost of the model project scheduled to be put into operation in 2025 amounts to nearly $4.7 billion, and (3) the model project is environment-friendly without any CO{sub 2} gas emission because of hydraulic and tidal power generation. (NEDO)

Underground docking of shields for the first time under the sea by MSD method. Shield for a gas pipe line to Shin Nagoya thermal power station of Chubu Electric Power Co. Ltd.,; Kaiteika hatsu no MSD koho ni yoru shirudo chichu setsugo. Chubu Denryoku Shin Nagoya Karyoku Hatsudensho gas dokan shirudo koji

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Y. [Shimizu Corp., Tokyo (Japan)

1997-04-25

MSD (mechanical shield docking) method is a method for mechanical docking two shields which have been extended simultaneously from both ends of one section of tunnel boring to shorten work term. One of the two shields has a piercing ring on its tip and another has a receiving ring. In the final stage of boring, the two ring are docked directly by piercing-receiving. The MSD method has been applied for the first time under sea to a boring work of an under sea tunnel on a route of a gas pipe line from Chita LNG base, Aichi prefecture to the title power station. This paper reports the outline of the shield machine and horizontal boring for confirming shield position that is a key to an underground docking as well as docking work. In the horizontal boring, after the shield machine on receiving side had reached the docking point predestined, the shield machine on piercing side conducted primary boring at 20 m front of the docking point and then secondary boring at 3 m front, whereby the boring hole was pierced into the shield machine on the receiving side. The accomplishment of this work made certain the reliability of MSD method even under sea. 1 ref., 13 figs., 3 tabs.

Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

Application of low bitrate image coding to surveillance of electric power facilities. Part 1. Proposal of low bitrate coding for surveillance of electric power facilities and examination of facilities region extraction method; Denryoku setsubi kanshi eno tei rate fugoka hoshiki no tekiyo. 1. Setsubi kanshiyo fugoka hoshiki no teian to setsubi ryoiki chushutsuho no kento

Energy Technology Data Exchange (ETDEWEB)

Murata, H.; Ishino, R. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

Current status of low bitrate image coding has been investigated, and a low bitrate coding suitable for the surveillance of electric power facilities has been proposed, to extract its problems to be solved. For the conventional image coding, the waveform coding has been used by which the images are processed as signals. While, for the MPEG-4, a coding method with considering the image information has been proposed. For these coding methods, however, image information lacks details primarily, when lowering the bitrate. Accordingly, these methods can not be applied when the details in the images are important, such as in the case of surveillance of facilities. Then, the coding method has been proposed by expanding the partially detailed coding, and by separating constituent images of facilities, such as power cables and steel towers, designated by operators. It is the special feature of this method that the method can easily respond to the low bitrate and the detailed information can be conserved by using the structure extraction coding for the designated partial image which is generally processed by the low bitrate waveform coding. 29 refs., 17 figs., 1 tab.

Fiscal 2000 survey on electrical power supply system for the purpose of reducing greenhouse effect gas. Three scenarios for spread of distributed power generation by 2010; 2000 nendo onshitsu koka gas sakugen no tame no denryoku kyokyu system ni kansuru chosa hokokusho. 2010 nen made no bunsangata dengen fukyu ni kansuru mittsu no scenario

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An examination was conducted concerning the course of spread of distributed power generation (on-site power generation of 2,000 kW or less) by the year 2010, with three scenarios prepared. In the scenario 1, the government will completely deregulates the power market and take no other steps, leaving the matter to market competition. The universal service will be abandoned, which means higher power prices for remote regions, contributing to the spread of home power generation. In the scenario 2, the government, having reached the limits of the nuclear propulsion policy, will adopt natural gas as the center of its electrical power policy, providing preferential treatments such as subsidies and tax exemptions and requesting the power companies to increase their usage. This will lead to higher transmission charges, with distributed power generation more advantageous to the IPPs in terms of cost. In the scenario 3, environmental awareness will make increase in the capacity quite difficult including power generation facilities and transmission/distribution network, and will invite a power crisis in the long run through insufficient capacity in power generation and transmission/distribution volume. Distributed power generation requiring no reinforcement to the grid will spread such as household-use type without system interconnection, solar cells or small fuel cells. (NEDO)

Studies of an application of a mobile communication system to the private telecommunication network. Part 1. Present condition of mobile communication system and proposal of the customer information network by PHS; Idotai tsushin system no denryoku tsushinmo eno tekiyo. 1. Idotai tsushin system no genjo to PHS ni yoru juyo kakei network no teian

Energy Technology Data Exchange (ETDEWEB)

Iwasaki, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-03-01

An application of various mobile communication systems to the electric power telecommunication network has been investigated. Among these, the customer information network by PHS (personal handy-phone system) has been proposed. Although great numbers of base stations are required for PHS, it can be applied as the customer information network by connecting to the power controller developed by the Central Research Institute of Electric Power Industry. The geostationary satellite telecommunication has been positively utilized by the electric power industry since the Hanshin-Awaji Great Earthquake. It can be used as the customer information network in the future. Since the radio access is a one-way communication, it cannot be applied to the electric power telecommunication network at present. It can be applied to the simple message communication or relatively low-speed data communication through the two-way communication. Public ground mobile telecommunication in the future includes various mobile telecommunication systems. To start the operation in 2000, the ITU (International Telecommunication Union) is making specifications common in the world. It is required to investigate the utilization as multipurpose systems. The network for PHS can be applied to the telecommunication network without optical cable. 20 refs., 5 figs., 3 tabs.

Fiscal 1997 report on the model project for the effective energy consumption in developing countries. Survey of changes of energy conservation technology and environmental protection technology in the oil refining industry in Japan; 1997 nendo chosa hokokusho. Hatten tojokoku energy shohi koritsuka model jigyo (Nippon sekiyu seiseigyo ni okeru sho energy gijutsu to kankyo taisaku gijutsu no hensen chosa hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For global scale measures to be taken for environmental protection, it becomes more and more important in the future to positively transfer and spread energy conservation technologies of Japan to overseas countries. Especially, it is effective for both economic growth in the Asian region and global environmental protection to transfer technologies which the oil refining industry has been developing and accumulating. Energy conservation in the oil refining industry means the energy conservation by strengthening the operational control at the first and second oil crises in the first stage, the energy conservation in the second stage which was accompanied by small and medium scale plant/equipment investments during several years after the first stage, and the energy conservation in the third stage which was accompanied by large scale investments from the first half of the 1980s to the present, resulting in improvement of 40% over before the first oil crisis. As to environmental protection measures, measures to reduce waste from oil refinery against air pollution and water pollution were prepared by the first half of the 1970s, and technologies were established of waste water treatment, flue gas desulfurization and denitrification. A lot of facilities for improvement of product quality and for low pollution were installed. In addition to environmental technologies, also in other industries, there were seen the heightening of thermal efficiency of kiln and thermal efficiency of cooling technique of clinker cooler in the cement industry and the improvement of productivity in the paper/pulp industry. 360 figs., 62 tabs.

Current status of and problems in ice heat storage systems contributing to improving load rate. Positive development of proliferation and expanded use measures as support of demand side management (DSM) activity (Tokyo Electric Power Co. Inc.); Fukaritsu kaizen ni kokensuru kori chikunetsu system no genjo to kadai. DSM katsudo no hashira to shite fukyu kakudaisaku wo sekkyoku tenkai (Tokyo Denryoku)

Energy Technology Data Exchange (ETDEWEB)

Masuda, H. [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1998-02-01

This paper introduces activities performed by Tokyo Electric Power Co., Inc. on ice heat storage systems. In the summer power peak in the Tokyo Electric Power area during fiscal 1996, the peak time, in which power was consumed in excess of 57 million kW, was only nine hours out of the annual supply time of 8760 hours. In other words, power generated by two large power plants is necessary for the nine hours, reducing the operation rate (load rate) of the power supply facilities. Therefore, Tokyo Electric Power has positioned the heat storage type air conditioning system as the center of the DSM activity, and is working on its proliferation and expanded use. An ice heat storage multi-air conditioner and a package air conditioner which can be installed in small buildings, and can deal with needs of individual discrete air conditioning were developed jointly with other electric power companies and device manufacturers. As a result, a commercial product called `Eco-Ice` made a debut. Since June 1997, the facilities subjected to commission in the `heat storage commission system` have been expanded to the heat source side facilities at customers to reduce initial capital investment. 5 figs., 1 tab.

FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

FY 1999 survey report on the cooperative basic project on the heightening of international energy consumption efficiency. Cooperative survey project in energy conservation/environmental protection fields in developing countries (Indonesia, Myanmar, the Philippines, Thailand and Vietnam); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo. Hatten tojokoku ni okeru sho energy kankyo hozen bun'ya kyoryoku chosa jigyo (Indonesia, Myanmar, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the pollution preventive administration, clean energy technology, etc. in fields of energy conservation technology, clean energy technology and environment in Japan, administrative officials, researchers and engineers in the fields concerned in Asian countries were invited to Japan for training with the aim of the technology transfer/spread to developing countries. In FY 1999, a total of 15 administrative officials and engineers were invited from Indonesia, Myanmar, the Philippines, Thailand and Vietnam, and had training at International Center for Environmental Technology Transfer. The themes for training are as follows: tackles with energy conservation/environmental protection by the Japanese government administration, pollution preventive measures against automobile gas emissions, pollution preventive measures against industrial gas emissions/waste water, technology for energy conservation, technology for industrial waste disposal, technology for recycling of wastes, etc. Reports were also made public on the situations of the countries participated in the project. Moreover, the field training was made at Yokkaichi complex, Sakakibara wind power plant, Hekinan thermal power plant of the Chubu Electric Power Co., Toyota Motor Corp., etc. (NEDO)

FY 1999 survey report on the cooperative basic project on the heightening of international energy consumption efficiency. Cooperative survey project in energy conservation/environmental protection fields in developing countries (Indonesia, Myanmar, the Philippines, Thailand and Vietnam); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo. Hatten tojokoku ni okeru sho energy kankyo hozen bun'ya kyoryoku chosa jigyo (Indonesia, Myanmar, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the pollution preventive administration, clean energy technology, etc. in fields of energy conservation technology, clean energy technology and environment in Japan, administrative officials, researchers and engineers in the fields concerned in Asian countries were invited to Japan for training with the aim of the technology transfer/spread to developing countries. In FY 1999, a total of 15 administrative officials and engineers were invited from Indonesia, Myanmar, the Philippines, Thailand and Vietnam, and had training at International Center for Environmental Technology Transfer. The themes for training are as follows: tackles with energy conservation/environmental protection by the Japanese government administration, pollution preventive measures against automobile gas emissions, pollution preventive measures against industrial gas emissions/waste water, technology for energy conservation, technology for industrial waste disposal, technology for recycling of wastes, etc. Reports were also made public on the situations of the countries participated in the project. Moreover, the field training was made at Yokkaichi complex, Sakakibara wind power plant, Hekinan thermal power plant of the Chubu Electric Power Co., Toyota Motor Corp., etc. (NEDO)

Current status of and problems in ice heat storage systems contributing to improving load rate. Proliferation and expanded use are intended by using the heat storage commission system and development of low-cost heat storage tanks (Kansai Electric Power Co. Inc.); Fukaritsu kaizen ni kokensuru kori chikunetsu system no genjo to kadai. Chikunetsu jutaku seido ya teikakaku chikunetsuso kaihatsu de fukyu kakudai mezasu (Kansai Denryoku)

Energy Technology Data Exchange (ETDEWEB)

Fujise, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

1998-02-01

This paper introduces activities performed by Kansai Electric Power Co., Inc. on ice heat storage systems. In the work on ice heat storage proliferation activities, systems for preferential treatment on power charge and a bounty for the system proliferation are available. Utilizing the ice heat storage system allows customers to use low-priced nighttime power as defined in an ice heat adjustment contract. Since this system reduces the power requirement under the contract, the running cost becomes less expensive. Furthermore, power charge discount system has been applied since fiscal 1997 according to a `heat storage peak adjustment contract`. In addition, in order to reduce the initial cost for an ice heat storage device, a system has been established, in which electric power companies pay bounty to device manufacturers for sales for proliferation. Under this system, if two ice heat storage units corresponding to 110 freezing tons are installed in an office building with an area of 10,000 m {sup 2}, a cost reduction of about 2.3 million yen is possible. For the purpose of reducing burden of initial investment on customers, a `lease system` and a `heat storage commission system` have been established to install and maintain air conditioners. 6 figs., 1 tab.

Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

Fundamental cooperation project in fiscal 2000 for improving international energy consumption efficiency. Investigations in relation with prevention of global warming (analytical comparison centering around cost effectiveness related to greenhouse effect gas (GHG) reduction in overseas countries); 2000 nendo kokusai energy shohi koritsu ka chosa nado kyoryoku kiso jigyo - chikyu ondanka boshi kanren chosa hokokusho. Kaigai deno GHG sakugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to provide discussion materials for measures to achieve the GHG emission reduction target, investigations and discussions have been made on the following subjects: cost effectiveness of reducing GHG emission by target countries and target technologies, use of maps and databases on the possible reduction quantity of GHG emission, the targeted countries and business categories. Regarding the target countries, investigations were made on the general situation of the energy consumption efficiency, difference between their energy consumption efficiency by industries and that in Japan, and the GHG emission quantities by sectors. As a result, 31 counties hopeful in reducing CO2 emission were selected. With regard to technologies to reduce CO2 emission, technologies having been practically used and proliferated in Japan were used as the base, whereas 43 technologies were systematized for such departments as industries, business operations, households, and transportation. According to a trial calculation on the effect of CO2 emission reduction, if the 43 technologies are applied to the 31 target countries, CO2 emission reduction of 698 million tons as a whole would be possible, for which the required expense was calculated as 114.4 trillion yen. In evaluating the CO2 emission reducing technologies, the cost effectiveness of each technology was evaluated by cost per GHG emission reduction of 1t-CO2. (NEDO)

FY 2000 report on the survey project on the policy for international energy utilization rationalization, etc. - model project on the heightening of international energy consumption efficiency. Viability survey of the project on energy conservation in the urea synthesis process in India; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo - kokusai energy shohi koritsuka nado model jigyo chosa hokokusho. Indo ni okeru nyoso gosei process sho energy jigyo jisshi kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of conserving energy and reducing greenhouse effect gas, a remodeling project was studied of urea plants constructed from the 1960s to the 1970s. Conditions for being companies for study are as follows: company has a production scale of more than 0.2 million t/y, adopts the complete circulation method, and will continue operation. And, Duncans Industries Ltd. (DIL) was selected. DIL owns the ammonia plant of 3 series x 400 t/d and the urea plant of 3 series x 682 t/d. In the modeling, stripper and carbamate condenser are added to the existing reactor as the main equipment. As a result of the study, the energy conservation effect was 13,667 toe/y, and the amount of reduction in greenhouse effect gas was 42,289 t-CO2/y. The total amount of this project was roughly estimated at 1.517 billion yen. By carrying out the project, the urea production cost is reduced approximately $9/t, but the project becomes unprofitable if the urea price is based on $188.1/t. (NEDO)

Fiscal 1998 research report (continued from the fiscal 1997 project). International survey project for rational energy use / Basic survey on efficient energy use in developing countries (Database construction project) / Survey on Japanese energy conservation technologies; 1998 nendo (1997 nendo jigyo kurikoshi) kokusai energy shiyo gorika nado chosa jigyo hatten tojokoku energy shohi koritsuka kiso chosa (database kochiku jigyo) chosa hokokusho. Nippon no sho energy gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

As a part of development of the energy conservation technology database, revision was made on 'Directory of Energy Conservation Technology in Japan' which was published to present the energy conservation technology of the Japanese energy-intensive industry to Asian countries in fiscal 1996. The previous directory was composed of 307 technical items, and 126 items among them were deleted and new 63 items were added through this revision. The technologies with energy conservation effects more than 10% were mainly selected by knowledge of the industrial members of the committee and other specialists. The energy conservation effect widely ranges from low-level one to high-level one, and the number of all the energy conservation technologies is enormous. Consequently, it should be considered that the applicable extent of the energy conservation technologies is dependent on the energy cost or economical situation of Japan and developing countries. (NEDO)

FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

Achievement report on developing superconductor power applied technologies in fiscal 1999 (2). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power generators. This paper summarizes the achievements thereof in fiscal 1999. A verification test was given on the rotor of an ultra high speed responding generator. In a sudden short circuit test using the different phase charging method, no anomalies were found such as quench generation and vibration changes, wherein the healthiness of the generator was verified. In the VVVF actuation test, knowledge was acquired on the actuation method when the ultra high speed responding generator is applied to a combined cycle plant. After the verification test has been completed, the disassembly inspections such as visual check and non-destructive test were performed. With regard to the vacuum leakage found in the rotor under very low temperatures, the causes were presumed and the countermeasures were discussed by observing the weld structures. In the design research, the conception design on the 200-MW pilot generator was reviewed by reflecting the results of the verification tests on the model generator. At the same time, trial design was made on a 600-MW target generator. In summarizing the overall research achievements, the achievements and evaluations were summarized on technological issues that have been allotted to each research member. (NEDO)

Achievement report for fiscal 1998 on the development of superconductor power application technology. 2. Research and development of superconducting wire and superconductive power generator, research of total system, research and development of refrigeration system, and verification test; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total sytsem no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The slow excitation response type power generator is studied when the rotor and stator of a 70,000kW-class model are combinedly subjected to an on-site verification test, when a good result is obtained. The rotor is disassembled for inspection, and its members are found to be sound without any problem in terms of mechanical strength. The quick excitation response type is studied when a 70,000kW model is experimentally built and subjected to an on-site verification test after a rotation and excitation test in the factory, when the pilot machine concept design is reviewed. In the study of a total system, efforts continue for the review of the model machine test method, improvement on generator design and analytical methods, development of operating methods, and the effect of its introduction into the power system. Since a He-refrigerated system is requested to exhibit high reliability for application to power equipment and to be capable of continuous long-period operation, a system having constituents with their reliability enhanced and an appropriate redundant system is developed, and a verification study is under way which will continue for more than 10,000 hours. Described also is an oil-free low-temperature turbo refrigerator. The latest quick excitation response type rotor is also tested for verification. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.14). Achievement report on joint research for utilizing Russia's now-unused high-viscosity crude oil as fuel for power generation; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.14). Russia miriyo konensei gen'yu no denryoku nenryo riyo kyodo kenkyu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Russkoye high-viscosity oil field is located in the western part of Siberia, Russia. Joint research is under way to develop a technology for reducing the viscosity for the collection of crude oil through the utilization of a gas condensate discharged by a neighboring gas field. This report comprises eight chapters, namely, (1) the background, purpose, and contents of the research, (2) Russia's oil resources and oil industry, (3) high-viscosity oil fields in Russia, (4) analysis of Russkoye crude oil and gas condensates yielded in Russia, (5) methods for viscosity reduction, (6) evaluation of combustibility, (7) scenario for developing the Russkoye oil field, and (8) research results as summarized and future tasks. Studied in chapter (5) are approaches to viscosity reduction, methods for emulsification, and a method for viscosity reduction by use of a gas condensate. These are tested and the results after analysis clearly show that the Russkoye crude oil, when blended with a gas condensate, will turn transportable and will provide a fuel equivalent to fuel oil C. (NEDO)

FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report refers, continuously to the Part 1, to the in-situ verification test of the slow-response type model machine rotor and to the review of the conceptual design of the pilot machine. On the basis of the R and D results of various element technology/partial models obtained before the previous fiscal year, the design, manufacturing and factory test had been conducted for a 70,000kW class slow-response type model machine rotor. This year, an in-situ verification test was performed to complete the test of all planned test items. Using the technological results obtained in the design, manufacturing and test of the 70,000kW class model machine, the conceptual design is being reviewed of the 200,000kW class pilot machine. In the aspect of the functional design, accurate grasping of the thermal load is essential for the purpose of attaining a large capacity for a superconducting generator, as a part of which a thermal load analytical method was planned to be established for a torque tube heat exchanger. The reasonableness of the analysis was verified through a comparison with the factory test result of the 70,000kW class slow-response type rotor, indicating good agreement between the calculation result and the actual measurement, and enabling the result to be obtained that explains dependency of the thermal load on the number of revolution. (NEDO)

Achievement report on developing superconductor power applied technologies in fiscal 1999 (1). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power applied technologies. This paper summarizes the achievements thereof in fiscal 1999. In research and development of the superconductor wire materials, decrease in loss and increase in capacity of the conductors were progressed for the Nb{sub 3}Sn wire material, whereas its mechanical properties and stability were evaluated. In research and development of the superconductor generators, an ultra high speed responding generator was verified of its healthiness in a sudden short circuit test. A linkage test with an operating 77-kV system was performed, wherein verification was given that the superconductor generator can be operated stably against various disturbances. In research and development of the freezing systems, an improved system was structured, which achieved operation of 11,390 hours in a single system as a result of the high reliability of the oil-free structure. In the verification tests, the ultra high speed responding model generator was connect to the freezing system to give such tests as load test, onerous test, actuation test by using the M-G system, and 77-kV system linkage test. The functions, reliability, and durability of the system were verified, and different data were acquired. (NEDO)

Report on investigations in fiscal 2000 on the global warming prevention related investigations in cooperative fundamental project of investigating improvement in international energy consumption efficiency. Analysis and comparison centering on cost effectiveness in relation with greenhouse gas (GHG) reduction in Japan; 2000 nendo kokusai energy shohi koritsuka chosanado kyoryoku kiso jigyo chikyu ondanka boshi kanren chosa hokokusho. Kokunai deno GHG sakyugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The present investigative research is intended to grasp the whole image of cost effectiveness of the energy saving and new energy technologies to suppress and reduce CO2 emission in Japan. Furthermore, the research considers the cost effectiveness and discusses the efficiency and the directionality of reducing CO2 emission from an estimation of the social introduction cost of individual technologies and quantity of CO2 emission reduction. These activities are intended to provide the fundamental items of information when discussing the measures to achieve the emission reduction target imposed on Japan. The research divides the whole aspect into energy conversion, industrial, consumer and transportation departments for discussion, and calculates the technological items that can be introduced by 2010 and the quantity of the introduction thereof, as well as the effect of reducing CO2 emission. Calculations are also performed on 27 elementary technologies in total and the CO2 emission reducing effect, assuming technological possibilities. Subsequently, analyses are carried out from the viewpoint of cost effectiveness by departments. It is shown that the average cost effectiveness is distributed in the range from 108,000 yen/ton to 1,129,000 yen/ton. Scenarios of reducing CO2 emission are discussed from the analyses of the cost effectiveness. (NEDO)

FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 2/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. The separate volume (2/2) included drawings of valve, fire detector, orifice, thermocouple, motor control equipment, etc. (NEDO)

Fiscal 1996 project on the modeling for effective energy consumption in developing countries under a consignment from NEDO. Recent on the results of the demonstrative study on scrap preheater of electric furnace in the iron making process (for public); 1996 nendo hatten tojokoku energy shohi koritsuka model jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Seitetsu katei ni okeru denkiro no genryo yonetsu sochi ni kakawaru jissho kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Indonesia is the biggest iron steel producing country in the ASEAN countries. Most of the production is produced by the electric furnace method in which iron steel scrap is used as a material. However, an energy saving measure in this method, the electric furnace scrap preheater using flue gas, has not yet been spread on a full scale. This R and D is aimed at developing jointly with Indonesia an electric furnace scrap preheater for medium/small size electric furnaces which are adoptable to the present iron making situation in Indonesia and installing it to the electric furnace of the iron making plant in Indonesia for a demonstrative study on energy saving, etc. Spread/expansion of the electric furnace scrap preheater which is an excellent energy saving system targeted expansion of energy saving technology not only of Indonesia, but of ASEAN countries and Japan. In this fiscal year, remodeling of part of the system was made by change of flue gas flow for increasing the energy saving effect, and at the same time, a research study was made of a scrap reheater effective as a total system. Moreover, the paper investigated technical data/information in Japan and overseas. 3 figs., 9 tabs.

FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 1/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. The plant at installation site has been run since 1995, having a production capacity of 50,000-60,000 tons. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. (NEDO)

FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

Current status of and problems in ice heat storage systems contribution to improving load rate. Contracts on Eco-Ice reached 240 cases by October 1997, an increase of 1.5 times over the same period of the previous year (Chubu Electric Power Co. Inc.); Fukaritsu kaizen ni kokensuru kori chikunetsu system no genjo to kadai. 1997 nendo 10 gatsu made no ekoaisu seiyaku wa 240 ken de tai zennen dokihi 1.5bai (Chubu Denryoku)

Energy Technology Data Exchange (ETDEWEB)

Urata, M. [Chubu Electric Power Co. Inc., Nagoya (Japan)

1998-02-01

This paper introduces activities performed by Chubu Electric Power Co., Inc. on ice heat storage air conditioning systems. Chubu Electric Power has worked with concerted efforts particularly on proliferation of an ice heat storage type air conditioning system, called `Eco-Ice`. A `heat storage air conditioner group` has been established in the sales department of the head office, and `market development groups` in branch offices to advance the recommendation activities. The Eco-Ice has been publicized on TV commercials, and the `97 Electric Power Heat Storage Air Conditioning Fair was held. Individual discrete type models were added to the product line-up in fiscal 1995. In addition, because of the system economy having been improved as a result of the improvements in the governmental subsidy system, power charge system, and support system, the number of Eco-Ice contracts is increasing rapidly. Two-hundred and forty Eco-Ice systems were contracted from April to October 1997, which means that peak shift capacity reached 7887 kW. Compared with the same period of fiscal 1996, the number of contract increased by 74 cases or 45% , and the peak shift capacity increased by 3148 kW or 66%. 4 figs.

Report on results for fiscal 1996 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In fiscal 1996, the initial cooling test and rotary excitation test were conducted for the 70,000kW slow-response type model machine, with the basic characteristics of the rotor verified such as the cooling characteristics, shaft vibration characteristics, mechanical strength, and superconductivity stability, and with the results of the studies explained. The rotor of the 70,000kW slow-response type model was installed in the test site, and the field test was carried out in 1997. For this purpose, research test was performed by the element technology of the model machine and the partial model. The technological development items, trial manufacture and test items were field winding, multi cylindrical rotor and damper. Upon the test results using the element and partial model, the design and manufacturing were implemented of the superconducting generator of a slow-response type excitation method with the output of 70,000kW class. Performed were the basic characteristic test, long-term operation test and severity test on the assumption of abnormality, verifying the characteristics and reliability of the generator as well as obtaining data concerning an excessive electromagnetic force and heat generation. From the test data and the analysis/evaluation results obtained on the model machine, the 200,000kW class pilot machine was reviewed in the conceptual design. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 1. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report explains the outline as Part 1. In fiscal 1997, the 10th year of the project, a multi cylindrical rotary model for which an in-situ verification test was finished was brought back to the plant and dismantled for examination, while the in-situ verification test of a slow-response type model machine rotor was conducted in combination with a refrigeration system. In addition, in the research of AC wire materials and oxide based materials, studies were made with a purpose of high characterization and long wire materialization. In the metallic materials, a 10kANbTi conductor was developed while, in oxide-based materials, research was done on performance improvement and wire materialization based on various synthesizing methods. The manufacturing, factory test and in-situ text were conducted for a 70,000kW model machine with the purpose of R and D of a 200,000kW class pilot machine. Examination was made on the test method of the 70,000kW class model machine, operation technology of a superconducting generation system, and the effect of introducing the superconducting generator into a power system. In the conventional refrigeration system, a single unit test was carried out for the liquefaction, liquid storing capacity, etc., of the system. The 70,000kW class model machine was put through a test for confirming the general operation including the refrigeration system. (NEDO)

FY 2000 research and development of fundamental technologies for AC superconducting power devices. R and D of fundamental technologies for superconducting power cables and faults current limiters, R and D of superconducting magnets for power applications, and study on the total systems and related subjects; 2000 nendo koryu chodendo denryoku kiki kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo soden cable kiban gijutsu no kenkyu kaihatsu, chodendo genryuki kiban gijutsu no kenkyu kaihatsu, denryokuyo chodendo magnet no kenkyu kaihatsu, total system nado no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for research and development of fundamental technologies for AC superconducting power devices has been started, and the FY 2000 results are reported. The R and D of fundamental technologies for superconducting power cables include grasping the mechanical characteristics associated with integration necessary for fabrication of large current capacity and long cables; development of barrier cable materials by various methods; and development of short insulated tubes as cooling technology for long superconducting cables, and grasping its thermal/mechanical characteristics. The R and D of faults current limiters include introduction of the unit for superconducting film fabrication, determination of the structures and layouts for large currents, and improvement of performance of each device for high voltages. R and D of superconducting magnets for power applications include grasping the fundamental characteristics of insulation at cryogenic temperature, completion of the insulation designs for high voltage/current lead bushing, and development of prototype sub-cooled nitrogen cooling unit for cooling each AC power device. Study on the total systems and related subjects include analysis for stabilization of the group model systems, to confirm improved voltage stability when the superconducting cable is in service. (NEDO)