WorldWideScience

Sample records for taikai gakujutsu koenkai

  1. Preprint of the Fall 1997 JSAE (Japan Society of Automotive Engineers) Meeting Science Lecture. No. 976; Jidosha gijutsukai 1997 nen shuki taikai gakujutsu koenkai maezurishu. 976

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    The Fall 1997 JSAE Meeting Science Lecture was held in Hiroshima on October 21-23, 1997. This report summarized 90 out of the total 244 lectures. As for reports on gasoline engines, the following were included: Effects of fuel and air mixing on WOT output in direct injection gasoline engine, Mixture formation of direct gasoline injection engine, etc. As to sensors, Study of a fuel injection quantity sensor in diesel engine, Development of air fuel ratio sensor, etc. Concerning automotive parts, Prediction and optimization of friction characteristics of brake pads, The new conceptual copper alloy bearing for diesel engine to achieve longer life under higher load, A study of improvement in 1st ring`s gas-seal, etc. In relation to driving, accidents, etc., Effects of cellular telephone manipulation on driver`s performance, Study on traffic accidents mechanism with automatic recording systems, etc

  2. Preprint of the Fall 1997 JSAE (Japan Society of Automotive Engineers) Meeting Science Lecture. No. 974; Jidosha gijutsukai 1997 nen shuki taikai gakujutsu koenkai maezurishu. 974

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This is a comprehensive compilation of 66 papers made public in the Fall 1997 JSAE Meeting, including the following by field: 13 papers on engine combustion; 4 on analysis of chassis structure; 12 on travel of vehicles; 6 on improvement of exhaust gas from diesel engines; 9 on basic study of combustion characteristics using fuels such as methanol, natural gas and hydrogen; 3 on study of heat flux on the piston face of internal engines; others on processing technology, noise, etc. Among these, the following were paid attention to as studies aiming at reducing NOx and smoke of diesel engines for pollution prevention: Emission and combustion characteristics of multiple stage diesel combustion, and Study on homogeneous charge diesel combustion engine. As studies on the use of petroleum substituting fuels, Visualizing ignition and combustion of methanol mixtures in a diesel engine, Improving performance and emissions in a diesel engine dual-fueled with natural gas, and Fundamental combustion characteristics of lean hydrogen mixtures

  3. Preprint of the Fall 1997 JSAE (Japan Society of Automotive Engineers) Meeting Science Lecture. No. 975; Jidosha gijutsukai 1997 nen shuki taikai gakujutsu koenkai maezurishu. 975

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    No. 975 preprint of the Fall 1997 JSAE was summarized. As for the engine development, papers were made public on a study of reciprocating engine with Z mechanism, the combustion control system, etc. Attention was paid to internal combustion engine-electricity hybrid systems in terms of global warming prevention, and a study was made of environmental improvement effects by introducing next-generation automobiles. Image analysis and computer utilization in the structural design were also described. As to diesel engines, the combustion system and the exhaust gas problem were much studied. Also made were flow analysis on air conditioning and evaluation on the indoor thermal environment. Concerning the manufacturing process and materials, a lot of improvements were made public on thermal fatique resistance, reinforced materials, adoption of ceramics, corrosion resistance/wear resistance, etc. Operability and human engineering, and dynamics and safety are also important themes. Relating to the fuel, low fuel comsumption and additives were studied. The paper reported transmissions and the control systems, torque-transmitting mechanism, frictional property, etc. Especially, research/development were also much made of friction/wear resistant materials. ed and developed

  4. 1996 Fall Meeting of JSAE (Japan Society of Automotive Engineers). Preprint of the academic lecture (No. 965); JSAE 1996 nendo shuki taikai. Gakujutsu koenkai maezurishu (No.965)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    The JSAE 1996 Fall Meeting was held in Sapporo during October 22-24, and 232 papers were reported. As for the vehicle safety in collision, a lot of papers were made public including the ones having the following titles: Study on vehicle body structure at frontal collision; Study on the load-stress simulation method for vehicle structure; High strain rate deformation behavior of steel sheet for automotive anti-collision parts; Optimization of the crush characteristic of door inner material for occupant injury in side impact. As to the measurement relation, the following were reported: Development of three-dimensional dynamic clearance and interference evaluation method for engine with video measurement; Proposal for a new laboratory automation standard IMACS96; Small gas samples analyzed for NOx by electron capture detector; Mechanism analysis of shock absorber rattling noise; etc. With relation to the catalytic system, reported were Study on electrically heated catalyst (EHC) system; Development of NOx removal catalysts for lean-burn gasoline engines; Study on the applicability of three-way catalyst system to medium/heavy duty gasoline trucks; etc.

  5. 1996 Fall Meeting of JSAE (Japan Society of Automotive Engineers). Preprint of the academic Lecture (No.964); JSAE 1996 nen shuki taikai. Gakujutsu koenkai maezurishu (No.964)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    The JSAE 1996 Fall Meeting was held in Sapporo during October 22-14, and 232 papers were reported. As for the aerodynamic relation of automobiles, a lot of papers were made public including the ones titled as follows: Measurement of automobile aerodynamic noise in wind tunnels; Estimation and reduction of aerodynamic noise by motorcycle scale model testing; flow visualization around door mirror thinking about adhesion of raindrops and wind noise; The aerodynamic interferences on a vehicle caused by another different length vehicle in tandem driving. As to the driving behavior, the following were reported: The influence of automatic vehicle control algorithm on traffic flow; Analysis of the benefits of freight consolidation in auto parts delivery; The development of simulation model of the driver`s behavior upon which a car was parked; etc. With relation to the control system, lots of papers were read including the following: Brake force distribution control system using hydraulic actuator; The effect of 4ws with H{sup infinity} control system theory in comparison with conventional 4ws; An adaptive LQ control system design for front and rear wheel steering vehicle.

  6. 1994 JSAE (Society of Automotive Engineers of Japan) Spring Convention Proceedings. No. 941 (115-165); JSAE 1994 nen shunki taikai gakujutsu koenkai maezurishu. No.941, 115-165

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-20

    The science conference on the automotive technology research and development was held on May 11-13, 1994 in Yokohama, and 165 papers were reported. As for driving simulation(DS) for vehicles, reports are made on driving simulator with large displacement motion base - its evolution and the development of basic research tool, experimental analysis of avoidance maneuver using a driving simulator, comparison of handling characteristics between a driving simulator for tracked vehicles and a real vehicle, etc. As to auto parts, pitting fatigue strength of caburized gears, evaluation of corrosion protection of automotive chromated galvanized bolts, development of aluminum powder metallurgy composites for cylinder liners, development of a new nitrided stainless steel piston ring, etc. Further studied were made on development of new protocol for in-vehicle LAN, development of YONDEN electric vehicle `PIVOT,` development of electric scooter for practical use, etc. With regard to diesel engines, reported were diesel combustion improvement and emissions reduction with high pressure fuel injection, exhaust emission behaviors of a heavy duty diesel engine under various driving conditions, etc.

  7. 1996 Fall Meeting of JSAE (Japan Society of Automotive Engineers). Preprint of the academic lecture (No. 966); JSAE 1996 nendo shuki taikai. Gakujutsu koenkai maezurishu (No.966)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    The JSAE 1996 Fall Meeting was held in Sapporo during October 22-24, and 232 papers were reported. As for the lubricating oil, the papers with the following titles were made public: Influence of engine oil viscosity and friction modifiers on coefficients of friction; Study on diesel fuel lubricity; Effect of diesel fuel components on lubricity; etc. As to the driving sensation, reported were: Study of incidence factor of car sickness and the evaluation of a passenger`s feeling and his physiological responses; A study on evaluation of drowsiness; Experimental study on vigilance decline during a monotonous-driving simulation task; etc. In the computer soft relation, Development of ECU data acquisition and analysis support system; Development of software engineering system for automotive control system; etc. In addition, a lot of papers were read including the following: A study on the heat transfer performance improvement of condenser for automotive air conditioning system; A study for preventing corrosion for tube of aluminum oil coolers; A study of engine cooling fan.

  8. Proceedings of the 95th SEGJ Conference; Butsuri tansa gakkai dai 95 kai (1996 nendo shuki) gakujutsu koenkai koen ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    This is a proceedings of the 95th SEGJ (The Society of Exploration Geophysicists of Japan) Conference (fall 1996). The number of the papers made public totaled 72: 6 in seismic survey processing; 11 in seismic survey; 7 in ground vibration; 5 in strong magnetic force; 7 in logging/underground measurement; 6 in the IP method and others; 5 in spontaneous potential/streaming potential; 6 in electrical prospecting; 6 in tomography; 5 in electromagnetic method; 8 in time-domain electromagnetic method/radar. As for the seismic survey, reported were the following papers titled An experiment of exploration using the active-faults exploration system; Detection of traveltime delay caused by dilation of an artificial fracture due to pressurization; Faults survey by 3D reflection seismics; etc. As to the ground vibration, Applicability of the spatial autocorrelation method for estimation of basement structure in Kanto Plain-Array measurements of microtremors close to the Iwatsuki and Shimousa Deep Borehole Observatory; Prediction of strong acceleration motion depended on focal mechanism; etc. With relation to the logging/underground measurement, Trial to active seismic while drilling; Estimation of fracture aperture using simulation technique: etc.

  9. Preliminary collection 891 of lectures/papers in symposium by Society of Automotive Engineers of Japan. Jidosha gijutsukai gakujutsu koenkai maezurishu 891

    Energy Technology Data Exchange (ETDEWEB)

    1989-05-29

    This preliminary collection collected lectures given and papers presented in the symposium by the Society of Automotive Engineers of Japan to be held in May, 1989. Totally 86 papers, together with two basic lectures, were presented therein. The categories comprise two basic lectures titled Future problems on CVT and automatic transmission and Advances of gasoline engine and measuring techniques, ten papers for the gasoline engine, covering the supercharger, air/fuel mixture, noise, bore deformation, etc., ten papers for the diesel engine, covering the exhaust gas, supercharger, methanol engine, etc., ten papers for the car body, covering the aerodynamical characteristics and movement of car body, movement analysis of motor bicycle, head lamp, painting, etc., ten papers for the car parts, ten papers for the fuel injection, ten papers for the engine parts, covering the piston, oil ring, cylinder, connecting rod, plug, rotary, car heater, etc., three papers for the car production, covering the line control, welding, production method, etc., seven papers for the car steering and stability, eight papers for the vibration and noise attenuation and three papers for the others. 370 refs., 857 figs., 100 tabs.

  10. 1996 Annual Meeting of Geothermal Research Society of Japan. Abstracts with programs; Nihon chinetsu gakkai 1996 nendo gakujutsu koenkai. Koen yoshishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-08

    This is a compilation of all the papers made public in the meeting. It includes a total of 111 papers; 14 papers on physical survey, 14 on hot dry rock, 10 on geology, 4 on drilling, 4 on utilization, 21 on heat structure, 3 on scale, 4 on logging, 24 on reservoir, and 13 on geochemistry. Main themes were as follows: Study of MT method and self-potential method and results of the physical survey in New Zealand in the physical survey section. Plan in Ogachi, Akita pref. and development in Hijiori, Yamagata, pref. in the hot dry rock section. Heat source evaluation in the Yuzawa-Ogachi area, Akita pref., and electrical resistivity feature of hot spring reservoir in green tuff bed, Japan, in the geology section. Study of the MWD system in the drilling section. Utilization of geothermal water in Hokkaido in the utilization section. Formation of smectite scale, silica precipitation, and scale prevention measures for steam turbines, in the scale section. High-temperature PT memory system in the logging section. Study of areas of Kuju volcano, Mori, Kakkonda, Otake and Hacchobaru, in the heat structure section. Analysis of fluids from well of the geothermal power plant in the geochemistry section. Heat extraction system from magma in the reservoir section.

  11. Proceeding of the 97th (Fall, Fiscal 1997) SEGJ Conference; Butsuri tansa gakkai dai 97 kai (1997 nendo shuki) gakujutsu koenkai koen ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-22

    The 97th SEGJ (The Society Exploration Geophysicists of Japan) Conference was held on October 22-24, 1997 at Hokkaido University, and 85 papers were made public in addition to special lectures titled `Geology and resources in Hokkaido,` `The foggy sea and imagination - Map of the Northwest Pacific in the 17th and 18th centuries.` In the section of the reflection method exploration, reports were made on Estimation of a subsurface structure by using a shallow seismic engineering exploration system with multiple function (SWS), 3D seismic experiment in the Minaminoshiro area, Akita - Data processing, etc. As to the ground vibration, reported were Nature of short-period microtremors on the cliff-like ground, Ground characteristics at observation site of strong motion in Hachinohe Inst. Tech., Hachinohe, Aomori, etc. Concerning the tomography, Source inversion in the full-wave tomography, Effects of fluid-filled boreholes on resistivity tomography, etc. Reports were additionally made in the sections of characteristics of seismic waves, sensor/system, electromagnetic method, radar/gravity, electric exploration, magnetic exploration, logging/borehole measurement, remote sensing/temperature, etc

  12. Proceeding of the 96th (spring, fiscal 1997) SEGJ Conference; Butsuri tansa gakkai dai 96 kai (1997 nendo shunki) gakujutsu koenkai koen ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-27

    This is a proceedings of the 96th SEGJ (The Society of Exploration Geophysicists of Japan). As for the well measurement, described were seismic survey and logging of geothermal wells and hot dry rock artificial reservoirs. As to the reflection method, analyzed were characteristics of seismic propagation and stratum structures. In the data processing, topics were on the neural network, stacking process and resolution, migration, etc. Concerning the electromagnetic method, research results were reported of TEM, CSAMT, EM tomography, MT method, etc. About the electrical exploration, introduced were resistivity structures by the electrical log, and exploration by the streaming potential or self-potential methods. Relating to the gravity/magnetic force exploration, reported were continuous gravity monitoring of geothermal activity, magnetic structures of rock, data on magnetic susceptibility, aeromagnetic survey, and remote sensing. As to the underground radar method, described were the survey of buried pipes and the inspection of fracture zones using the borehole radar, etc. With respect to the global system, the global structure was discussed from a global point of view. Additionally, reports were made on radioactive prospecting, seismometer observation, and ground motion.

  13. Preprint of the 40th material study joint lecture of Science Council of Japan; Dai 40 kai Nippon gakujutsu kaigi zairyo kenkyu rengo koenkai maezurishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-19

    The paper stated mostly topics from special lectures. Composite materials have a lot of potentialities, and there are larger expectations in flexible and high-strength soft composites rather than the conventional high rigidity ones. As to micro-machines, the problems are on mechanical property of the element, environment/friction/fracture/life, etc. and the evaluation method of the characteristics was studied. Concerning the research and development of the intellectual structure system, the introductive study has entered the second year. Ultimately, structures have functions similar to those of the living organism had, and conduct self-diagnosis, self-repair and autonomous-response. Railroad structures receive regular inspections according to the rule, and a half of the objects for the inspection are cracks, unbonding and weathering of concrete. With the Hanshin Awaji great earthquake especially, the anti-earthquake reinforcement has been expedited. In various kinds of materials, the finer the crystal particle becomes, the greater the high temperature deforming ability becomes. When the particle size is below the critical particle size, it shows superplasticity. The study is advancing. As to high density secondary batteries, introduced especially were Ni-hydrogen batteries and Li batteries.

  14. FY1999 Meeting of The Society of Heating, Air-Conditioning and Sanitary Engineering of Japan. Hot water supply system; 1999 nendo gakujutsu koenkai gaiyo. Kyuto

    Energy Technology Data Exchange (ETDEWEB)

    Oze, H. [Toyo University, Tokyo (Japan)

    1999-12-05

    G-5 and 6 measure and investigate actual state of use of hot water supply systems in dormitories used by persons living alone without their families and by unmarried persons to collect fundamental data. G-5 considers how hot water is used, by making a questionnaire survey on the subject houses, and identifies the consumption trend of heat, water and hot water in the hot water supply systems as a whole. G-6 selected eleven houses from among the houses discussed in the previous report to identify the trend of use of hot water by each house. Also, quantity of hot water used in every day of the week is estimated. G-7 discusses methods for estimating water temperatures at faucets of water pipes from the water sources. This is intended to raise the accuracy of tap water temperature conversion coefficient by districts used for calculating estimated heat quantity as a parameter 'hot water supply energy consumption coefficient' to evaluate energy saving performance of a hot water supply facility. G-8 performs numerical simulations changing different parameters in the hot water supply piping system by using a heat loss calculation model for the existing household hot water supply piping. It executes evaluation on energy conservation performance of each model. G-9 estimates efficiency of instantaneous household gas hot water supply devices, not only on thermal efficiency of devices during steady state combustion, but also on non-steady state such as start-up, and discusses methods to derive actual efficiency by using calculations. (translated by NEDO)

  15. Proceedings of the 94th SEGJ (The Society of Exploration Geophysicists of Japan) Conference; Butsuri tansa gakkai dai 94 kai (1996 nendo shunki) gakujutsu koenkai koen ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The fiscal 1996 SEGJ Conference was held in Tokyo during May 15-17, and 101 papers were reported. As for disaster prevention, the following were reported: Questionnaire investigation for the earthquake, Localization of b-values and maximum earthquakes, Cooperative measurements of microtremors in the north-eastern region of Nishinomiya City, Hyogo Pref., etc. As to elastic wave data recording and modeling data processing, Optimization of dynamite source depth for seismic surveys, Simulation of breakage of heterogeneous materials caused by detonative loading, etc. With relation to archeology, radar, and refraction method, Reexamining results of Iwatoyama tumulus by means of directive antenna, Application of geophysical method to investigation of old castle, etc. Concerning microtremors and surface waves, Estimation of shallow ground structure using short-period microtremors array observation, etc. Besides, papers were reported on electromagnetism, tomography, gravity/magnetism/numerical calculation, measurement while drilling, etc. Moreover, a symposium on underground structures in the Hanshin/Awaji area as viewed from geophysical exploration was held presenting nine papers.

  16. FY1999 Meeting of The Society of Heating, Air-Conditioning and Sanitary Engineering of Japan. Air flow analysis II; 1999 nendo gakujutsu koenkai gaiyo. Kiryu kaiseki 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-05

    B-4 reported the result on particle size distribution experiment and numerical calculation with FEM and {kappa}- {epsilon} model using a welding simulation equipment for generation and removal of welding fume in a narrow site. Discussion was held on the position of an exhaust hood. B-5 reported the study results on indoor air flow conditions derived from a movable nozzle air conditioning system by model experiment and numerical analysis. Disagreement of both results between the experiment and calculation in the case of two diffusing nozzles attached at 30 degrees toward the inside was improved by shortening a sampling time for calculation. B-6 reported the study results on some parameters such as wind velocity, flow rate and inlet position, and the energy saving effect of an air curtain (wall outlet, floor inlet) to control air conditioning areas for a part of large spaces by numerical analysis of air flow. Discussion was held on calculation of 2-D flow and layered flow. B-7 is the 5th research report on measurement of air flow conditions such as measurement of large space environment by video camera and balloon. Study on the camera for automatic measurement, and the identification technique of balloon positions was reported. (translated by NEDO)

  17. Proceedings of the 89th (Fall, fiscal 1993) SEGJ (the Society of Exploration Geophysicists of Japan) Conference. Butsuri tansa gakkai dai 89 kai (1993 nendo shuki) gakujutsu koenkai ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    The 89th SEGJ Conference was held during October 12-14, 1993. With relation to the exploration of elastic wave, reported are comparison study on an S/N ratio improvement method for noise in VIBROSEIS exploration, discrimination of the pseudo bright spot by AVO (amplitude versus offset) method in petroleum exploration, cross-adit and cross-well velocity tomography, AE doublet analysis in the hydraulic fracturing experiment on hot dry rock, estimation of crack extension surface, exploration of Aso caldera, seismic exploration ahead of the tunnel face, etc. Borehole televiewer by ultrasonic wave image is also reported. Relating to electrical prospecting, reports are made on simultaneous analysis of resistivity and charging rate, grasp of fluid transfer by SP change in the hydraulic fracturing experiment, synthetic focused resistivity logging using array normal logging equipment, borehole resistivity profiling, etc. Lectures totals 64 including reports further made on migration, refraction method analysis, VSP (vertical seismic profile), ground vibration, gravity/magnetic force/thermal structure, simulation, etc.

  18. Proceedings of the papers read in the 47th Science Lecture Meeting of the Society of Materials Science, Japan; Nippon Zairyo Gakkai dai 47 ki gakujutsu koenkai koen ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-21

    As to the evaluation and analysis of organs and strength at high temperature, papers were reported on high temperature reformation behavior, damage models and analysis/evaluation, long-time creep fatigue, fatigue strength, fatigue crack development, microstructures of super alloys/composite materials, high temperature characteristics of ductile materials, etc. Relating to the materials database related to phase transformation and its application to simulation, reported were quenching, phase transformation behavior and structural formulas, concrete, polycrystal reformation, timber and dynamics, analysis of composite materials, etc. Concerning strength characteristics and evaluation of surface reforming materials, papers on abrasion, thin films, monocrystal, grain boundary, corrosion, etc. About the design/evaluation of ceramic materials, the sintering process, reformation/fracture behaviors and their simulation, strength characteristics of composite ceramics, fatigue, evaluation of superconduction characteristics, etc. The paper also described composite materials/organism use materials, polymer, magnetic materials, etc. As the impact behavior of materials/structures, reported were impact pressure welding, impact loads, fatigue/fracture of composite materials, thermal analysis, etc. From time to time, measuring methods were also reported

  19. FY1999 Meeting of The Society of Heating, Air-Conditioning and Sanitary Engineering of Japan. Air conditioning systems for various facilities; 1999 nendo gakujutsu koenkai gaiyo. Kakushu shisetsu kucho system

    Energy Technology Data Exchange (ETDEWEB)

    Iwamoto, K. [Takenaka Corp., Osaka (Japan)

    1999-12-05

    B-49 reported the outline of an artificial weather room composed of one inner room and two outer rooms, and its temperature change and temperature profiles during air conditioning. The room is scheduled to be used for evaluation of air conditioning systems, thermal performance evaluation of building materials and study on ventilation efficiency. B-50 reported the seasonal measurement results on thermal environment, and cooling and heating use patterns of living rooms and common spaces of 4 welfare homes for aged persons, and showed that room temperature difference in winter should be considered. Measurement data on facilities with floor heating were required. B-51 reported the experiment and numerical analysis results on thermal environment, draft sensation, condensation and radiation effect of patient bedrooms by using a full-scale 4-bed room model with a specific outlet developed for patient bedroom air conditioning. B-52 reported the outline of an air conditioning system for vegetable factories, and its performance evaluation result during cooling. The effect of blackout curtains and local air conditioning was reported. B-53 reported the comparison study result on air conditioning for animal breeding rooms by full-scale model experiment and numerical analysis. The line outlet + hanging wall + rack back exhaust system was most favorable from the viewpoint of temperature profile and prevention of pollutants from diffusion. (translated by NEDO)

  20. JCI Tokyo convention is held; JCI tokyo taikai wo kaisai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-10

    For 3 days on 15{approx}17 of Julies, Japan Concrete Inst. (Toyokazu Shiire chairman) held concrete technology annual meeting in the Tokyo big site in Tokyo and Ariake. Various events such as ready-mixed concrete seminar (participant: 562 person), joint seminar with the Korea concrete institute, observation were developed 20th concrete technology lecture (paper the report: 521 case participant real number: 1400 person), 12th concrete fair (exhibit: 95 case attendance number: 10150 person) center on present convention. The opinion in which the party of the first line of various quarters became heated on the direction in which the ready-mixed concrete will ought to advance based on performance definition and internationalization in the ready-mixed concrete seminar in this inside in future was exchanged. Whether it is the JIS ready-mixed concrete and whether quality audit system are necessary why. The severe order of more cheaply supplying the better concrete in the responsibility of the factory, also came out. Within the special lecture (participant: 548 person), it was an interest of the nation who obtained the time too, the fact of the president election that it does secret story especially and comes out happily heard it. In the new planning, 'the concrete which the primary school child makes' (it is introduced in this journal No. 614) was exhibited in the tip in the fair place. The figure of parent and child companion who gazed at the masterpiece which broke through the preliminary in each place was conspicuous. The still, schedule that the annual meeting in next time is held in the Sendai City on July 7{approx}9, 1999. (translated by NEDO)

  1. Pitfalls in the ankle-brachial index and brachial-ankle pulse wave velocity

    Directory of Open Access Journals (Sweden)

    Ato D

    2018-04-01

    Full Text Available Dai Ato Gakujutsu Shien Co., Ltd., Tokyo, Japan Background: The ankle-brachial index (ABI and pulse wave velocity (PWV are indices of atherosclerosis and arterial stiffness. The Japan-made measuring devices of those indices have spread widely because of their convenience and the significance of the parameters. However, studies that comprehensively discuss the various pitfalls in using these indices are not available.Methods: This study presents several representative pitfalls in using the ABI and brachial-ankle PWV (baPWV by showing the result sheets of the device, “the Vascular Profiler”. Furthermore, some considerations when utilizing these indices in the future are also discussed.Results: Several diseases such as arteriosclerosis obliterans (ASO, arterial calcification in the lower limb, arterial stenosis in the right upper-limb, aortic valve diseases, arterial stenosis in the upper-limb of the contralateral side of the hemodialysis access, are the representative pitfalls when evaluating ABI and baPWV. Moreover, a measurement error is found to actually exist. Furthermore, same phenomena are considered most likely to occur when using other similar indices and devices.Conclusion: The ABI and baPWV are the useful and significant biomarkers. Nevertheless, caution is sometimes necessary when interpreting them. Moreover, rigorous patient exclusion criteria should be considered when using those indices in the severely conditioned patient population. And the results of this study can be applied to enhance the literacy using other indices, such as the cardio-ankle vascular index and other similar devices. Keywords: ankle-brachial index, pulse wave velocity, peripheral arterial disease, aortic valve disease, hemodialysis

  2. 53rd Concrete Technology Conference. Repair, Reinforcement 3; Dai 53 kai semento gijutsu taikai. Hoshu, hokyo 3

    Energy Technology Data Exchange (ETDEWEB)

    Wakasugi, Mikio

    1999-08-10

    Yanagi et al. investigated crack-blocking effect of salt-removing effect of electrodeposition method using a ZnSO{sub 4} solution. Nishida et al. also paid attention to the same method, and carried out the investigation by applying the electrodeposition method using two kinds of solutions, i.e., ZnSO{sub 4} solution and MgCl{sub 2} solution, to samples where dry shrinkage and cracks are generated, then observing crack-blocking state and improvement state of mortar interior with a SEM and measuring pore size distribution. Fukushima carried out theoretical analysis in respect to the effect of surface finishing treatment in concrete to perform neutralization until the backs of reinforcing bars upon the corrosion inhibition of the reinforcing bars. Kubo et al. direct their attention to 100% silane without using any organic solvent, specifically, they used five kinds of silane with different molecular weight and molecular structure, performed surface treatment of concretes with different moisture state and density-solid state and measured moisture permeability and water permeability. Ueki et al. proposed a method for evaluating fluidity of high-flow mortar used in steel plate-lining operation of anti-earthquake reinforcing works, namely, a new testing method using a device for pouring high-flow mortar into a certain-spaced clearance from J funnel. (NEDO)

  3. Factors associated with high brachial–ankle pulse wave velocity in non-hypertensive and appropriately treated hypertensive patients with atherosclerotic risk factors

    Directory of Open Access Journals (Sweden)

    Ato D

    2017-10-01

    Full Text Available Dai Ato,1 Toshitami Sawayama2 1Gakujutsu Shien (Academic Support Co., Ltd. Tokyo, 2Sawayama Clinic, Okayama, Japan Abstract: While pulse wave velocity (PWV correlates with blood pressure (BP, its extent differs between patients, and some cases of high PWV in normotensives are present. Moreover, PWV frequently remains high in hypertensive patients despite adequate BP control. The factors associated with such phenomena are yet to be elucidated. Here, we investigated the factors associated with brachial–ankle PWV (baPWV in 107 patients whose systolic BP was under 140 mmHg at their latest baPWV measurement. There were 64 controlled hypertensives and 43 normotensives. Multivariate regression analysis identified age, hypertension, body mass index (BMI, systolic BP, and heart rate (HR as independent factors for baPWV. Next, we divided the subjects into groups according to their age (in 5-year increments and calculated the mean and standard deviation (SD of the baPWV for each group. For each age group, we defined patients with a baPWV above the mean + SD baPWV for the group as the high-baPWV cohort. Multivariate logistic regression analysis revealed that BMI, hypertension, and smoking were independent determinants of a high-baPWV subject. This represents the first study to report the existence of the hypertensive state itself as one of the independent predictors of high baPWV in normotensive and well-treated hypertensive patients. This finding implies that the hypertensive state itself possibly worsens arterial stiffness independently from aging in spite of adequate BP maintenance. To prevent the early progression of arterial stiffness, the application of an appropriate intervention during the early stages of hypertension is important and the continuation of an appropriate BP treatment is suggested. Keywords: arterial stiffness, brachial–ankle pulse wave velocity, heart failure, hypertension, peripheral arterial disease

  4. It participates in the 97th learning lecture, social meeting; Dai 97 kai Gakujitsu koenkai{center_dot}konshinkai ni sankashite

    Energy Technology Data Exchange (ETDEWEB)

    Maruta, T.; Moriya, M.; Izumi, K.

    1999-01-01

    An inorganic material academic meeting the 97th learning lecture, a social meeting and a study tour meeting were held for both days of (Thu) for 5 days in November 4 (Wed), the 10th year of Heisei. Contents of a lecture go into the large area to the thing that that method analysis technique structure analysis formation response thing materiality side was examined, the spot in the construction, building field like contents. A problem such as CO{sub 2} is an especially important problem as a negative legacy due to the industrial development, the diffusion of the car, and so on. (NEDO)

  5. 1989 Joint convention record of institutes of electrical and information engineers, Japan (Part 1). Heisei gannen denki joho kanren gakkai rengo taikai koen ronbunshu (Bunsatsu 1)

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-25

    In this volume, part 1, reports are included on protection of communication equipment for power supply against thunderbolt, status quo of thunderbolt observation, etc. in the field of 'Protection of information communication equipment against thunderbolt and thunderbolt observation.' In the area of 'Latest trend for practical use of linear motorcars,' there are reports on the world trend for practical use, present and future aspect of superconductive magnetic levitation railway, present state and future aspect of HSST, status quo and future aspect of transrapid Maglev, present state and future aspect of linear subway, present state and future aspect of M bahn, etc. In conncetion with 'Expert system for power network system,' status quo in Japan and foreign countries and future trend are reported. Other reports are also included concerning the control of 'Present state of control theory application to the control of electric motor,' 'Technological trend for the reliability improvement in control system,' 'Superconduction and precision measurement,' and 'Latest trend of fuzzy information processing technology.' 370 refs., 224 figs., 32 tabs.

  6. 55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-10

    Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

  7. Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-07

    Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

  8. Summary of the papers of the 95th Meeting of the West Japan Society of Naval Architects. Joint meeting of three shipbuilding societies in fall, fiscal 1997; Seibu Zosenkai dai 95 kai reikai ronbun gaiko. 1997 nendo shuki zosen sangakkai rengo koenkai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    The paper summarized the papers on the following: estimation of the propulsion performance by the surface vortex lattice method using model ship flow field data; wave-making resistance calculation and performance estimation by the Rankine source method; calculation method of wave-making resistance of Catamaran and solution method of the hydrofoil problem using the convenient panel method; study of estimation of hydrodynamic forces acting on ship in maneuvering motion; study of the combined plant using generator use diesel exhaust heat; mathematical structure of the ocean container transport system; developmental OTEC plants in Indonesia. In relation to structural dynamics/strength problems, reports were made on the hull longitudinal strength theory, FEM modeling in analyses of buckling/plasticity collapse of deflection panels, etc. Further reported were a consideration of the use classification of hull use steel sheets considering fracture toughness, and changes of aspect ratios of small surface cracks emanating from a toe of corner boxing. Concerning ocean structures, there are experimental studies on vibration in water of a semi-spherical shell fixed in water, and a behavior of huge floating structures in regular waves

  9. Summary of monographs made public in the 93rd meeting by West Japan Society of Naval Architects. Lecture meeting sponsored jointly by three shipbuilding societies for fall in 1996; Seibu zosenkai dai 93 kai reikai ronbun kogai. 1996 nendo shuki zosen sangakukai rengo koenkai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    A lecture meeting sponsored by the three ship building societies for fall in 1996 was held on November 14 and 15, 1996 at the Hiroshima Prefecture Information Plaza, where 16 monographs were presented. With regard to fluid dynamic problems in vessels, reports were given on experimental studies on performance of tandem hydrofoils in highspeed regions, solution methods for non-steady two-dimensional hydrofoil problems by using a simple panel method, a consideration on lateral inclination during maneuvering operation, and a new prediction approach for ships maneuvering hydrodynamics. With respect to structural material strength, reports were made on one consideration on buckling and plastic breakdown strength characteristics of surface fine grain steel plates, a study on buckling and final strength of square plates subjected to load in combined planes, and one consideration on evaluating life to generate corrosion fatigue cracking. Other reports were also given on a theoretical study on sea shock load acting on two-dimensional floating bodies, a study on a method for setting design hydrographic conditions, and a numerical simulation on flow and density field in the Kagoshima bay in summer by using a multi-layer model.

  10. 18th national meeting for energy saving promotion (prize winning case awarded by Ministry of International Trade and Industry). ; Development of air cooling equipment for gas turbine combustion. Dai 18 kai sho energy suishin zenkoku taikai (tsusho sangyo daijinsho jusho jirei). ; Gas turbine nenshoyo kuki reikyaku sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-30

    This paper describes a development of air cooling equipment for gas turbine combustion in a 1090-MW combined plant and a discussion on its cooling effect. An open-type gas turbine reduces its output when suction temperature rises. This is a characteristic for a combined plant with high heat efficiency not capable of exhibiting its ability in summer. As a result of testing cooling methods, water spraying nozzles utilizing latent evaporation heat of water were installed at a gas turbine suction opening. Effects of cooling the gas turbine combustion air resulted in reducing the gas turbine suction temperature by 1.8[degree]C as a result of water spray at an ambient temperature of 30[degree]C and a relative humidity of 60%, increasing the plant output by 12 MW as a result of cooling the suction air, and improving the heat efficiency by about 0.035%. The amount of ammonia used for reducing nitrogen oxide generation was reduced by 10.8 kg/hr. Under an assumption of experimenting the water spray in summer on a 15-hour per day basis for 50 days, a calculation indicates an annual economic effect of about 13.5 million yen. 8 figs., 8 tabs.

  11. 18th national meeting for energy saving promotion (prize winning case awarded by Minstry of International Trade and Industry). ; Optimization of additive carrying argon gas in continuous casting. Dai 18 kai sho energy suishin zenkoku taikai (tsusho sangyo daijinsho jusho jirei). ; Renzoku chuzo ni okeru tenkazai hansoyo argon gas no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-30

    An optimal amount of argon gas carrying CaSi additive particles was discovered in a continuous casting process and a stable operation method was established to conserve energy and cost. CaSi particles are added into molten steel to prevent steel materials from cracking, and argon gas is used in carrying the CaSi particles to prevent oxygen and nitrogen from mixing into the molten steel. The proposed modification plan intends to use the existing facilities up to the seal rotary machine, and to reduce the size and length of the carrying pipes thereafter, the length of the flexible tubes, and the size of the booster. A verification test was carried out. As a result of measuring the CaSi particle scattering distribution, it was found that an in-pipe flow velocity of 25 m/s produces a narrow scattering distribution and has the particles impinge on the molten steel dropping position concentratedly. It was also learned that the in-pipe flow velocity of 25 m/s can increase the solid-air ratio to 0.81 to 1.21. Operations of the modified machine reduced the argon gas amount by 5.2 m[sup 3]N/min (reduction rate of 61%) and realized stabler CaSi particle injection which improved the Ca yield by 9.4%. 14 figs., 7 tabs.

  12. 18th national meeting for energy saving promotion (prize winning case awarded by Ministry of International Trade and Industry). ; Saving energy in annealed coil cooling equipment by using volatile corrosion inhibitor. Dai 18 kai sho energy suishin zenkoku taikai (tsusho sangyo daijinsho jusho jirei); Kikasei boseizai ni yoru shodon coil reikyaku setsubi no sho energy

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-30

    A method and a device for preventing rust in annealed coils using volatile corrosion inhibitor (VCI) were put into practical use. Air cooling using dehumidified air and corrosion inhibiting air cooling have been used to prevent rusting caused by condensation on surfaces of coils being cooled, but these methods consume a very large amount of energy. As a result of discussing new corrosion inhibiting methods, cyclohexylamine carbonate (CHC) showed a highest corrosion prohibition capability as a VCI. Because CHC has a strong odor, new deodorants have been searched by combining it with special metallic salts. It was found that the range where a deodorant can be added without impeding the corrosion prohibiting effect is from 20% to 30%. A test for practical application indicated that rusting could be suppressed even using a VCI with concentration as low as 0.4 ppm to 0.8 ppm if the velocity of cooling air on coil surfaces is held from 0.2 m/s to 0.4 m/s. A high-accuracy continuous CHC analyzing method was established that uses a nitrogen oxide analyzer. The required installation space was reduced to 1/15 to 1/20 and the running cost to 1/8 to 1/10 of conventional methods. 11 figs., 4 tabs.