Drift reversal capability in helical systems

International Nuclear Information System (INIS)

Yokoyama, M.; Itoh, K.; Okamura, S.; Matsuoka, K.; Nakajima, N.; Itoh, S.-I.; Neilson, G.H.; Zarnstorff, M.C.; Rewoldt, G.

2003-01-01

The maximum-J (J is the second adiabatic invariant) capability, i.e., the drift reversal capability, is examined in quasi-axisymmetric (QAS) stellarators and quasi-poloidally symmetric (QPS) stellarators as a possible mechanism for turbulent transport suppression. Due to the existence of non-axisymmetry of the magnetic field strength in QAS configurations, a local maximum of J is created to cause the drift reversal. The increase of magnetic shear in finite beta equilibria also has favorable effect in realizing the drift reversal. The radial variation of the uniform magnetic field component plays a crucial role for the drift reversal in a QPS configuration. Thus, the drift reversal capability and its external controllability are demonstrated for QAS and QPS stellarators, by which the impact of magnetic configuration on turbulent transport can be studied in experiments. (author)

Tank waste remediation system characterization project quality policies. Revision 1

International Nuclear Information System (INIS)

Trimble, D.J.

1995-01-01

These Quality Policies (QPs) describe the Quality Management System of the Tank Waste Characterization Project (hereafter referred to as the Characterization Project), Tank Waste Remediation System (TWRS), Westinghouse Hanford Company (WHC). The Quality Policies and quality requirements described herein are binding on all Characterization Project organizations. To achieve quality, the Characterization Project management team shall implement this Characterization Project Quality Management System

Influence of gravity on the orientation of vestibular induced quick phases.

Science.gov (United States)

Pettorossi, V E; Errico, P; Ferraresi, A; Draicchio, F

1995-01-01

In rabbits and cats the orientation of the quick phases (QPs) of the vestibulo-ocular reflex (VOR) was studied varying the head position in space. At different head tilt positions, QPs induced by step vestibular stimulation disaligned with respect to the stimulus toward the orientation of the earth's horizontal axis. The rabbits' QPs were horizontal during yaw stimulation and remained horizontal in a range of head pitch of +/- 90 degrees (reorientation gain = 1). Therefore, the slow compensatory responses (CSPs) progressively disaligned compared with the QPs. QPs induced by roll stimulation also showed horizontal orientation, although these were rare in the upright position and occurred more frequently when the head was pitched. In cats only the yaw-induced QPs were coplanar with the stimulus, while QPs induced by pitching were mostly oblique. It followed that in either yawing or pitching, the QPs had their end point scattered within a horizontally elongated area of the visual field. When tilting cats in the frontal plane, the orientation of QP trajectories changed with respect to the stimulus so that the end point distribution tended to remain aligned toward the horizontal instead of being fixed in the orbit. The reorientation gain decreased from 1 to 0.5 by increasing the head tilt. On the basis of difference regarding eye implantation and motility it was suggested that the effect of gravity on the orientation of QPs could be aimed at maintaining the interocular axis aligned with the horizon in the rabbit and at orientating the visual scanning system in the horizontal plane in the cat.

Quantitative analysis of stress thallium-201 studies: comparison of SPET and planar imaging in the detection of CAD

International Nuclear Information System (INIS)

Ziada, G.; Hayat, N.; Abdel-Dayem, H.M.; Hassan, I.

1986-01-01

The value of thallium-201 tomographic sections in the detection of coronary artery disease is illustrated by comparing visual interpretation (VTS) and quantitative analysis (QTS) with visual planar study (VPS) and quantitative analysis of planar study (QPS), referring to coronary angiography (CA) as the standard technique. It is concluded that visual assessment of single photon emission tomography (VTS) is more valuable than all other techniques (VPS, QPS and QTS) for detecting and localizing coronary artery disease. (UK)

Upgrade of the protection system for superconducting circuits in the LHC

CERN Document Server

Denz, R; Formenti, F; Meß, K H; Siemko, A; Steckert, J; Walckiers, L; Strait, J

2010-01-01

Prior to the re-start of the Large Hadron Collider LHC in 2009 the protection system for superconducting magnets and bus-bars QPS will be substantially upgraded. The foreseen modifications will enhance the capability of the system in detecting problems related to the electrical interconnections between superconducting magnets as well as the detection of so-called aperture symmetric quenches in the LHC main magnets.

Upgrade of the protection system for superconducting circuits in the LHC

OpenAIRE

Denz, R; Dahlerup-Petersen, K; Formenti, F; Meß, K H; Siemko, A; Steckert, J; Walckiers, L; Strait, J

2009-01-01

Prior to the re-start of the Large Hadron Collider LHC in 2009 the protection system for superconducting magnets and bus-bars QPS will be substantially upgraded. The foreseen modifications will enhance the capability of the system in detecting problems related to the electrical interconnections between superconducting magnets as well as the detection of so-called aperture symmetric quenches in the LHC main magnets.

Quantum-dot-based homogeneous time-resolved fluoroimmunoassay of alpha-fetoprotein

Energy Technology Data Exchange (ETDEWEB)

Chen Meijun; Wu Yingsong; Lin Guanfeng; Hou Jingyuan; Li Ming [Institute of Antibody Engineering, School of Biotechnology, Southern Medical University, Guangzhou, 510515 (China); Liu Tiancai, E-mail: liutc@smu.edu.cn [Institute of Antibody Engineering, School of Biotechnology, Southern Medical University, Guangzhou, 510515 (China)

2012-09-05

Highlights: Black-Right-Pointing-Pointer QDs-based homogeneous time-resolved fluoroimmunoassay was developed to detect AFP. Black-Right-Pointing-Pointer The conjugates were prepared with QDs-doped microspheres and anti-AFP McAb. Black-Right-Pointing-Pointer The conjugates were prepared with LTCs and another anti-AFP McAb. Black-Right-Pointing-Pointer Excess amounts of conjugates were used for detecting AFP without rinsing. Black-Right-Pointing-Pointer The wedding of QPs and LTCs was suitable for HTRFIA to detect AFP. - Abstract: Quantum dots (QDs) with novel photoproperties are not widely used in clinic diagnosis, and homogeneous time-resolved fluorescence assays possess many advantages over current methods for alpha-fetoprotein (AFP) detection. A novel QD-based homogeneous time-resolved fluorescence assay was developed and used for detection of AFP, a primary marker for many cancers and diseases. QD-doped carboxyl-modified polystyrene microparticles (QPs) were prepared by doping oil-soluble QDs possessing a 605 nm emission peak. The antibody conjugates (QPs-E014) were prepared from QPs and an anti-AFP monoclonal antibody, and luminescent terbium chelates (LTCs) were prepared and conjugated to a second anti-AFP monoclonal antibody (LTCs-E010). In a double-antibodies sandwich structure, QPs-E014 and LTCs-E010 were used for detection of AFP, serving as energy acceptor and donor, respectively, with an AFP bridge. The results demonstrated that the luminescence lifetime of these QPs was sufficiently long for use in a time-resolved fluoroassay, with the efficiency of time-resolved Foerster resonance transfer (TR-FRET) at 67.3% and the spatial distance of the donor to acceptor calculated to be 66.1 Angstrom-Sign . Signals from TR-FRET were found to be proportional to AFP concentrations. The resulting standard curve was log Y = 3.65786 + 0.43863{center_dot}log X (R = 0.996) with Y the QPs fluorescence intensity and X the AFP concentration; the calculated sensitivity was 0

Evaluation of Skin Penetration of Diclofenac from a Novel Topical Non Aqueous Solution: A Comparative Bioavailability Study.

Science.gov (United States)

Nivsarkar, Manish; Maroo, Sanjaykumar H; Patel, Ketan R; Patel, Dixit D

2015-12-01

Different topical formulations of diclofenac have varying skin penetration profile. Recent advances in science and technology has led to the development of many new formulations of drugs for topical drug delivery. One such technological development has led to the innovation of Dynapar QPS, a novel, non-aqueous, quick penetrating solution (QPS) of diclofenac diethylamine. This study was aimed to measure the total exposure from the drug penetrating the skin in healthy human subjects and comparing the relative systemic bioavailability of Dynapar QPS(®) with diclofenac emulgel. A 200 mg of diclofenac from either Dynapar QPS(®) (5 ml) or emulgel (20 g) was applied on back of subject as per the randomisation schedule. Blood samples were collected up to 16 hours post drug application. Plasma concentration of diclofenac was measured by pre-validated HPLC method. Pharmacokinetic (PK) parameters like Cmax, Tmax, t1/2, AUC0-t, AUC0-∞, and Kel, of diclofenac were determined for both the formulations. Mean Cmax after administration of Dynapar QPS(®) and diclofenac emulgel were 175.93 and 40.04 ng/ml, respectively. Tmax of diclofenac was almost half with QPS compared to emulgel (5.24 hrs versus 9.53 hrs respectively). The mean AUC0-t and AUC0-∞ after administration of Dynapar QPS(®) was higher as compared to diclofenac emulgel (AUC0-t: 1224.19 versus 289.78 ng.h/ml, respectively; AUC0-∞: 1718.21 versus 513.83 ng.h/ml, respectively). None of the subject experienced any adverse event during the study. The results indicate an enhanced penetration and subsequent absorption of diclofenac from Dynapar QPS(®) as compared to diclofenac emulgel. Higher penetration is likely to translate into better pain relief in patients.

Difference in quick phases induced by horizontal and vertical vestibular stimulations: role of the otolithic input.

Science.gov (United States)

Pettorossi, V E; Errico, P; Ferraresi, A

1997-01-01

Quick phases (QPs) induced by horizontal and vertical sinusoidal vestibular stimulations were studied in rabbits, cats, and humans. In all the animals, large and frequent horizontal QPs were observed following yaw stimulation in prone position. By contrast, QPs were almost absent during roll stimulation in rabbits, and they were small and oblique during pitch stimulation in cats and humans. As a result of these differences, the range of gaze displacement induced by vestibular stimulations was greater in the horizontal plane than in the vertical one. We also found that the trajectory of the QPs in rabbits was kept horizontal even when the yaw rotation was off vertical axis of +/- 45 degrees in the sagittal plane. Moreover, in the rabbit, the rare horizontal QPs induced by roll stimulation did not change their orientation at various pitch angles of roll stimulation axis. The QPs were also analyzed following roll stimulation of the rabbit in supine position. In this condition, in which the otolithic receptors were activated in the opposite way compared to prone position, large vertical QPs were elicited. We concluded that these results provide evidence that the otolithic signal plays a role in controlling occurrence and trajectory orientation of the QPs.

Role of cerebellar nodulus and uvula on the vestibular quick phase spatial constancy.

Science.gov (United States)

Pettorossi, V E; Grassi, S; Errico, P; Barmack, N H

2001-01-01

We investigated the orientation of quick phases (QPs) of vestibularly-induced eye movements in rabbits in response to "off-vertical" sinusoidal vestibular stimulation. We also examined the possible role of the cerebellar nodulus and ventral uvula in controlling QP spatial orientation and modification. During "off-vertical" vestibular stimulation QPs remained aligned with the earth's horizontal plane, while the slow phases (SPs) were aligned with the plane of vestibular stimulation. This suggests that QPs are coded in gravito-inertial coordinates and SPs in head coordinates. When rabbits were oscillated in the light (20 degrees peak-to-peak; 0.2 Hz) about an "off-vertical" axis for 2 h, the QPs changed their trajectory, abandoning the earth's horizontal plane to approach the plane of the stimulus. By contrast, in the absence of conjunctive optokinetic stimulation, QPs remained fixed in the earth's horizontal plane even after 2 h of "off-vertical" stimulation. The conjunctive combination of optokinetic and vestibular stimulation caused QPs to change their plane of rotation. After lesion of the nodulus-uvula the ability of rabbits to reorient QPs during conjoint vestibular-optokinetic stimulation was maintained. We conclude that the space orientation and adaptation of QPs do not require cerebellar control.

Control system architecture: The standard and non-standard models

International Nuclear Information System (INIS)

Thuot, M.E.; Dalesio, L.R.

1993-01-01

Control system architecture development has followed the advances in computer technology through mainframes to minicomputers to micros and workstations. This technology advance and increasingly challenging accelerator data acquisition and automation requirements have driven control system architecture development. In summarizing the progress of control system architecture at the last International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS) B. Kuiper asserted that the system architecture issue was resolved and presented a ''standard model''. The ''standard model'' consists of a local area network (Ethernet or FDDI) providing communication between front end microcomputers, connected to the accelerator, and workstations, providing the operator interface and computational support. Although this model represents many present designs, there are exceptions including reflected memory and hierarchical architectures driven by requirements for widely dispersed, large channel count or tightly coupled systems. This paper describes the performance characteristics and features of the ''standard model'' to determine if the requirements of ''non-standard'' architectures can be met. Several possible extensions to the ''standard model'' are suggested including software as well as the hardware architectural feature

Otolithic and extraocular muscle proprioceptive influences on the spatial organization of the vestibulo- and cervico-ocular quick phases.

Science.gov (United States)

Pettorossi, V E; Manni, E; Errico, P; Ferraresi, A; Bortolami, R

1997-03-01

The cervico-ocular reflex (COR) was studied alone or in combination with the vestibulo-ocular reflex (VOR) in the rabbit. Step stimulations of the body with respect to the fixed head induced small slow compensatory responses followed by large compensatory quick phases (QP). These responses remained aligned with the horizon at different head pitch angles. The QP reorientation in space was due to the gravity influence on the otolithic receptors. The vestibular induced QPs exhibit a similar pattern. Because of this reorientation, the reduction of the amplitude of the vestibular induced QPs, due to the addition of the COR, was maintained even at different static head positions. The electrolytic lesion of the ophthalmic branch of the trigeminal nerve deeply affected the space orientation of the COR. In particular, the cervically induced compensatory QPs of the eye ipsilateral to the lesion showed a remarkable variability of their trajectories and they lost space reorientation. These findings suggest that the coordinate system controlling the QPs is influenced by signals originating from both head position in space and eye position in the orbit.

Quasiparticle scattering by quantum phase slips in one-dimensional superfluids

International Nuclear Information System (INIS)

Khlebnikov, S.

2004-01-01

Quantum phase slips (QPS) in narrow superfluid channels generate momentum by unwinding the supercurrent. In a uniform Bose gas, this momentum needs to be absorbed by quasiparticles (phonons). We show that this requirement results in an additional exponential suppression of the QPS rate (compared to the rate of QPS induced by a sharply localized perturbation). In BCS-paired fluids, momentum can be transferred to fermionic quasiparticles, and we find an interesting interplay between quasiparticle scattering on QPS and on disorder

Standard NIM instrumentation system

International Nuclear Information System (INIS)

1990-05-01

NIM is a standard modular instrumentation system that is in wide use throughout the world. As the NIM system developed and accommodations were made to a dynamic instrumentation field and a rapidly advancing technology, additions, revisions and clarifications were made. These were incorporated into the standard in the form of addenda and errata. This standard is a revision of the NIM document, AEC Report TID-20893 (Rev. 4) dated July 1974. It includes all the addenda and errata items that were previously issued as well as numerous additional items to make the standard current with modern technology and manufacturing practice

INTEGRATIVE AUGMENTATION OF STANDARDIZED MANAGEMENT SYSTEMS

Directory of Open Access Journals (Sweden)

Stanislav Karapetrovic

2008-03-01

Full Text Available The development, features and integrating abilities of different international standards related to management systems are discussed. A group of such standards that augment the performance of quality management systems in organizations is specifically focused on. The concept, characteristics and an illustrative example of one augmenting standard, namely ISO 10001, are addressed. Integration of standardized augmenting systems, both by themselves and within the overall management system, is examined. It is argued that, in research and practice alike, integrative augmentation represents the future of standardized quality and other management systems.

Control system architecture: The standard and non-standard models

International Nuclear Information System (INIS)

Thuot, M.E.; Dalesio, L.R.

1993-01-01

Control system architecture development has followed the advances in computer technology through mainframes to minicomputers to micros and workstations. This technology advance and increasingly challenging accelerator data acquisition and automation requirements have driven control system architecture development. In summarizing the progress of control system architecture at the last International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS) B. Kuiper asserted that the system architecture issue was resolved and presented a open-quotes standard modelclose quotes. The open-quotes standard modelclose quotes consists of a local area network (Ethernet or FDDI) providing communication between front end microcomputers, connected to the accelerator, and workstations, providing the operator interface and computational support. Although this model represents many present designs, there are exceptions including reflected memory and hierarchical architectures driven by requirements for widely dispersed, large channel count or tightly coupled systems. This paper describes the performance characteristics and features of the open-quotes standard modelclose quotes to determine if the requirements of open-quotes non-standardclose quotes architectures can be met. Several possible extensions to the open-quotes standard modelclose quotes are suggested including software as well as the hardware architectural features

Rough Standard Neutrosophic Sets: An Application on Standard Neutrosophic Information Systems

Directory of Open Access Journals (Sweden)

Nguyen Xuan Thao

2016-12-01

Full Text Available A rough fuzzy set is the result of the approximation of a fuzzy set with respect to a crisp approximation space. It is a mathematical tool for the knowledge discovery in the fuzzy information systems. In this paper, we introduce the concepts of rough standard neutrosophic sets and standard neutrosophic information system, and give some results of the knowledge discovery on standard neutrosophic information system based on rough standard neutrosophic sets.

Standard-E hydrogen monitoring system shop acceptance test procedure

Energy Technology Data Exchange (ETDEWEB)

Schneider, T.C.

1997-10-02

The purpose of this report is to document that the Standard-E Hydrogen Monitoring Systems (SHMS-E), fabricated by Mid-Columbia Engineering (MCE) for installation on the Waste Tank Farms in the Hanford 200 Areas, are constructed as intended by the design. The ATP performance will verify proper system fabrication.

Standard-E hydrogen monitoring system shop acceptance test report

International Nuclear Information System (INIS)

Schneider, T.C.

1997-01-01

The purpose of this report is to document that the Standard-E Hydrogen Monitoring Systems (SHMS-E), fabricated by Mid-Columbia Engineering (MCE) for installation on the Waste Tank Farms in the Hanford 200 Areas, are constructed as intended by the design. The ATP performance will verify proper system fabrication

Intelligent Transportation Systems : critical standards

Science.gov (United States)

1999-06-01

Intelligent Transportation Systems (ITS) standards are industry-consensus standards that provide the details about how different systems interconnect and communicate information to deliver the ITS user services described in the National ITS Architect...

Computer systems and software description for Standard-E+ Hydrogen Monitoring System (SHMS-E+)

International Nuclear Information System (INIS)

Tate, D.D.

1997-01-01

The primary function of the Standard-E+ Hydrogen Monitoring System (SHMS-E+) is to determine tank vapor space gas composition and gas release rate, and to detect gas release events. Characterization of the gas composition is needed for safety analyses. The lower flammability limit, as well as the peak burn temperature and pressure, are dependent upon the gas composition. If there is little or no knowledge about the gas composition, safety analyses utilize compositions that yield the worst case in a deflagration or detonation. Knowledge of the true composition could lead to reductions in the assumptions and therefore there may be a potential for a reduction in controls and work restrictions. Also, knowledge of the actual composition will be required information for the analysis that is needed to remove tanks from the Watch List. Similarly, the rate of generation and release of gases is required information for performing safety analyses, developing controls, designing equipment, and closing safety issues. This report outlines the computer system design layout description for the Standard-E+ Hydrogen Monitoring System

Building Standards based Science Information Systems: A Survey of ISO and other standards

Science.gov (United States)

King, Todd; Walker, Raymond

Science Information systems began with individual researchers maintaining personal collec-tions of data and managing them by using ad hoc, specialized approaches. Today information systems are an enterprise consisting of federated systems that manage and distribute both historical and contemporary data from distributed sources. Information systems have many components. Among these are metadata models, metadata registries, controlled vocabularies and ontologies which are used to describe entities and resources. Other components include services to exchange information and data; tools to populate the system and tools to utilize available resources. When constructing information systems today a variety of standards can be useful. The benefit of adopting standards is clear; it can shorten the design cycle, enhance software reuse and enable interoperability. We look at standards from the International Stan-dards Organization (ISO), International Telecommunication Union (ITU), Organization for the Advancement of Structured Information Standards (OASIS), Internet Engineering Task Force (IETF), American National Standards Institute (ANSI) which have influenced the develop-ment of information systems in the Heliophysics and Planetary sciences. No standard can solve the needs of every community. Individual disciplines often must fill the gap between general purpose standards and the unique needs of the discipline. To this end individual science dis-ciplines are developing standards, Examples include the International Virtual Observatory Al-liance (IVOA), Planetary Data System (PDS)/ International Planetary Data Alliance (IPDA), Dublin-Core Science, and the Space Physics Archive Search and Extract (SPASE) consortium. This broad survey of ISO and other standards provides some guidance for the development information systems. The development of the SPASE data model is reviewed and provides some insights into the value of applying appropriate standards and is used to illustrate

Management system - correlation study between new IAEA standards and the market standards

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Dirceu Paulo de [Centro Tecnologico da Marinha em Sao Paulo (CTMSP), Ipero, SP (Brazil)], e-mail: dirceupo@hotmail.com; Zouain, Desiree Moraes [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)], e-mail: dmzouain@ipen.br

2009-07-01

In order to answer the growing concern of society with respect of the aspects that affect the quality of life, international and national regulatory bodies have developed standards that enable organizations to establish management systems for quality, environment and sustainable development, health, safety and social responsibility, among other functions. Within this context it is necessary to structure an integrated management system that promotes interests compatibility of several distinct and complementary functions involved. Considering this vision of the management system integration, the International Atomic Energy Agency (IAEA) decided to review the structure of safety standards on Quality Assurance - code and guides 50-C/SGQ1/ 14:1996, publishing, in 2006, IAEA GS-R-3 and IAEA GS-G-3.1 standards, enlarging the management approach of the previous standards, including the possibility of integrating the functions foremost mentioned. This paper presents the results about a correlation study between IAEA management system standards - IAEA GS-R-3: 2006, IAEA GS-G-3.1: 2006 and IAEA DS349 rev. 2007, this latter still a draft standard, with those market management system standards on quality - ISO 9001:2008, environmental - ISO 14001:2004, and occupational health and safety - BS OHSAS 18001:2007, identifying gaps, redundancies and complementarities among their requirements and guidances. The purpose of the study is to provide subsidies that could contribute to the structuring of a management system to nuclear facilities that satisfies, in an integrated manner, the common and complementary requirements and guidances of IAEA and market standards. (author)

Management system - correlation study between new IAEA standards and the market standards

International Nuclear Information System (INIS)

Oliveira, Dirceu Paulo de; Zouain, Desiree Moraes

2009-01-01

In order to answer the growing concern of society with respect of the aspects that affect the quality of life, international and national regulatory bodies have developed standards that enable organizations to establish management systems for quality, environment and sustainable development, health, safety and social responsibility, among other functions. Within this context it is necessary to structure an integrated management system that promotes interests compatibility of several distinct and complementary functions involved. Considering this vision of the management system integration, the International Atomic Energy Agency (IAEA) decided to review the structure of safety standards on Quality Assurance - code and guides 50-C/SGQ1/ 14:1996, publishing, in 2006, IAEA GS-R-3 and IAEA GS-G-3.1 standards, enlarging the management approach of the previous standards, including the possibility of integrating the functions foremost mentioned. This paper presents the results about a correlation study between IAEA management system standards - IAEA GS-R-3: 2006, IAEA GS-G-3.1: 2006 and IAEA DS349 rev. 2007, this latter still a draft standard, with those market management system standards on quality - ISO 9001:2008, environmental - ISO 14001:2004, and occupational health and safety - BS OHSAS 18001:2007, identifying gaps, redundancies and complementarities among their requirements and guidances. The purpose of the study is to provide subsidies that could contribute to the structuring of a management system to nuclear facilities that satisfies, in an integrated manner, the common and complementary requirements and guidances of IAEA and market standards. (author)

76 FR 16277 - System Restoration Reliability Standards

Science.gov (United States)

2011-03-23

... electric system. Blackstart units are essential to restart generation and restore power to the grid in the... Standard EOP-007-0. \\2\\ Mandatory Reliability Standards for the Bulk-Power System, Order No. 693, 72 FR... = $5,894,624. Title: Mandatory Reliability Standards for the Bulk-Power System. Action: FERC 725A...

Control Systems Cyber Security Standards Support Activities

Energy Technology Data Exchange (ETDEWEB)

Robert Evans

2009-01-01

The Department of Homeland Security’s Control Systems Security Program (CSSP) is working with industry to secure critical infrastructure sectors from cyber intrusions that could compromise control systems. This document describes CSSP’s current activities with industry organizations in developing cyber security standards for control systems. In addition, it summarizes the standards work being conducted by organizations within the sector and provides a brief listing of sector meetings and conferences that might be of interest for each sector. Control systems cyber security standards are part of a rapidly changing environment. The participation of CSSP in the development effort for these standards has provided consistency in the technical content of the standards while ensuring that information developed by CSSP is included.

Process Control System Cyber Security Standards - An Overview

Energy Technology Data Exchange (ETDEWEB)

Robert P. Evans

2006-05-01

The use of cyber security standards can greatly assist in the protection of process control systems by providing guidelines and requirements for the implementation of computer-controlled systems. These standards are most effective when the engineers and operators, using the standards, understand what each standard addresses. This paper provides an overview of several standards that deal with the cyber security of process measurements and control systems.

46 CFR 153.312 - Ventilation system standards.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Ventilation system standards. 153.312 Section 153.312... Handling Space Ventilation § 153.312 Ventilation system standards. A cargo handling space ventilation system must meet the following: (a) A ventilation system exhaust duct must discharge no less than 10 m...

Reconfigurable radio systems network architectures and standards

CERN Document Server

Iacobucci, Maria Stella

2013-01-01

This timely book provides a standards-based view of the development, evolution, techniques and potential future scenarios for the deployment of reconfigurable radio systems.  After an introduction to radiomobile and radio systems deployed in the access network, the book describes cognitive radio concepts and capabilities, which are the basis for reconfigurable radio systems.  The self-organizing network features introduced in 3GPP standards are discussed and IEEE 802.22, the first standard based on cognitive radio, is described. Then the ETSI reconfigurable radio systems functional ar

46 CFR 154.1205 - Mechanical ventilation system: Standards.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Mechanical ventilation system: Standards. 154.1205... CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Cargo Area: Mechanical Ventilation System § 154.1205 Mechanical ventilation system: Standards. (a...

Towards the longest run in CERN’s history

CERN Multimedia

CERN Bulletin

2010-01-01

Following the decisions taken at the Chamonix meeting, the teams are preparing the LHC to run at collision energies of 7 TeV during the coming 18-24 months. The consolidation of the nQPS connectors has been successfully completed and the magnet powering at high current has begun.   All the new electrical connectors of the nQPS have been succesfully tested. Since the last issue of the Bulletin, all of the approximately 4000 high-voltage electrical connectors of the new Quench Protection System (nQPS) have been replaced in record time. Teams are now upgrading the software on some of the electronic circuit boards. This work is already complete in half the machine. At the same time, the Hardware Commissioning group has started to power up the magnets in all the sectors. This is a lengthy process that involves gradually increasing the current to reach the 6 kA needed to steer beams at an energy of 3.5 TeV/beam. Currently, all the sectors have passed the tests at low current, and Sectors 1-2 has bee...

Orbit Feedback Operation with RCBX (MD 1209)

CERN Document Server

Wenninger, Jorg; Nisbet, David; Ponce, Laurette; Louro Alves, Diogo Miguel; CERN. Geneva. ATS Department

2017-01-01

The LHC Orbit Feedback (OFB) is able to drive any orbit corrector circuit (COD) to steer the LHC orbit. But during the first feedback tests in 2010, all attempts to use the common triplet orbit correctors (MCBX) failed because the QPS system installed to protect those magnets triggered power aborts as soon as the OFB steered the beam with those CODs. The reason was most likely the violation of the RCBX circuit acceleration limits. For this reason the MCBX orbit correctors were never driven by the OFB in regular operation. Although the performance of the OFB is generally excellent, the quality of the beam steering around IRs could be improved if the OFB could correct the orbit with the MCBX to counteract locally triplet quadrupole movements. The aim of this MD was to make a new attempt to use the MCBX in the OFB. The test was successful at injection (no circuit trip) and failed during the ramp (QPS power abort). The PC voltages and QPS Ures signals revealed the presence of voltage spikes with a period of 10~s...

75 FR 70696 - QPS Evaluation Services Inc.; Application for Recognition

Science.gov (United States)

2010-11-18

... about the ownership that would quality as a conflict under OSHA's independence policy. The amended... certification before use in the workplace. Consequently, if a test standard also covers any product for which...

[Study on emission standard system of air pollutants].

Science.gov (United States)

Jiang, Mei; Zhang, Guo-Ning; Zhang, Ming-Hui; Zou, Lan; Wei, Yu-Xia; Ren, Chun

2012-12-01

Scientific and reasonable emission standard system of air pollutants helps to systematically control air pollution, enhance the protection of the atmospheric environment effect and improve the overall atmospheric environment quality. Based on the study of development, situation and characteristics of national air pollutants emission standard system, the deficiencies of system were pointed out, which were not supportive, harmonious and perfect, and the improvement measures of emission standard system were suggested.

Antibiotic resistance of lactic acid bacteria

Directory of Open Access Journals (Sweden)

Bulajić Snežana

2008-01-01

Full Text Available Knowledge on the antibiotic resistance of lactic acid bacteria is still limited, possibly because of the large numbers of genera and species encountered in this group, as well as variances in their resistance spectra. The EFSA considers antibiotic resistances, especially transferable resistances, an important decision criterion for determining a strain's QPS status. There are no approved standards for the phenotypic or genotypic evaluation of antibiotic resistances in food isolates. Also, the choice of media is problematic, as well as the specification of MIC breakpoint values as a result of the large species variation and the possible resulting variation in MIC values between species and genera. The current investigations in this field showed that we might end up with a range of different species- or genus-specific breakpoint values that may further increase the current complexity. Another problem associated with safety determinations of starter strains is that once a resistance phenotype and an associated resistance determinant have been identified, it becomes difficult to show that this determinant is not transferable, especially if the resistance gene is not located on a plasmid and no standard protocols for showing genetic transfer are available. Encountering those problems, the QPS system should allow leeway for the interpretations of results, especially when these relate to the methodology for resistance phenotype determinations, determinations of MIC breakpoints for certain genera, species, or strains, the nondeterminability of a genetic basis of a resistance phenotype and the transferability of resistance genes.

Progress in standardization for ITER Remote Handling control system

International Nuclear Information System (INIS)

Hamilton, David Thomas; Tesini, Alessandro; Ranz, Roberto; Kozaka, Hiroshi

2014-01-01

Graphical abstract: - Highlights: • Standard parts specified for ITER Remote Handling (RH) control system. • Standard approach for VR modeling of structural deformations in real-time. • RH Core System produced as standard platform for RH controller applications. • Synthetic Viewing investigated and demonstrated. • Structured language defined for RH operation procedures and motion sequences. - Abstract: An integrated control system architecture has been defined for the ITER Remote Handling (RH) equipment systems, and work has been continuing to develop and validate standards for this architecture. Evaluations of standard parts and a standard control room work-cell have contributed to an update of the RH Control System Design Handbook, while R and D activities have been carried out to validate concepts for standard solutions to ITER RH problems: the use of a standard master arm with different slave arms, the achievement of high accuracy tracking of RH operations within virtual reality, and condition monitoring of RH equipment systems. The standardization efforts have been consolidated through the development of a freely distributable software platform to support the adoption of the ITER RH standards. The RH Core System installs on top of the CODAC Core System and provides the basic platform for the development of ITER RH equipment controller applications. The standardization work has continued in the areas of RH viewing, network communication protocols, and a structured language for programming ITER RH operations. Prototyping has been done on high-level control system applications, and R and D has been carried out in the area of synthetic viewing for ITER RH. These developments will be reflected in a new version of the RH Core System to be produced during 2013

Progress in standardization for ITER Remote Handling control system

Energy Technology Data Exchange (ETDEWEB)

Hamilton, David Thomas, E-mail: david.hamilton@iter.org [ITER Organization, Route de Vinon, 13115 St. Paul-lez-Durance (France); Tesini, Alessandro [ITER Organization, Route de Vinon, 13115 St. Paul-lez-Durance (France); Ranz, Roberto [Fusion for Energy, Torres Diagonal Litoral B3, Josep Pla 2, 08019 Barcelona (Spain); Kozaka, Hiroshi [Japan Atomic Energy Agency, Fusion Research and Development Directorate, Naka, Ibaraki-ken 311-0193 (Japan)

2014-10-15

Graphical abstract: - Highlights: • Standard parts specified for ITER Remote Handling (RH) control system. • Standard approach for VR modeling of structural deformations in real-time. • RH Core System produced as standard platform for RH controller applications. • Synthetic Viewing investigated and demonstrated. • Structured language defined for RH operation procedures and motion sequences. - Abstract: An integrated control system architecture has been defined for the ITER Remote Handling (RH) equipment systems, and work has been continuing to develop and validate standards for this architecture. Evaluations of standard parts and a standard control room work-cell have contributed to an update of the RH Control System Design Handbook, while R and D activities have been carried out to validate concepts for standard solutions to ITER RH problems: the use of a standard master arm with different slave arms, the achievement of high accuracy tracking of RH operations within virtual reality, and condition monitoring of RH equipment systems. The standardization efforts have been consolidated through the development of a freely distributable software platform to support the adoption of the ITER RH standards. The RH Core System installs on top of the CODAC Core System and provides the basic platform for the development of ITER RH equipment controller applications. The standardization work has continued in the areas of RH viewing, network communication protocols, and a structured language for programming ITER RH operations. Prototyping has been done on high-level control system applications, and R and D has been carried out in the area of synthetic viewing for ITER RH. These developments will be reflected in a new version of the RH Core System to be produced during 2013.

The LHC quench protection system

CERN Multimedia

2009-01-01

The new quench protection system (QPS) has the crucial roles of providing an early warning for any part of the superconducting coils and busbars that develop high resistance, as well as triggering the switch-off of the machine. Over 2000 new detectors will be installed around the LHC to make sure every busbar segment between magnets is monitored and protected. One of the major consolidation activities for the LHC is the addition of two new detectors to the quench protection system. A magnet quench occurs when part of the superconducting cable becomes normally-conducting. When the protection system detects an increased resistance the huge amount of energy stored in the magnet chains is safely extracted and ‘dumped’ into specially designed resistors. In the case of the main dipole chain, the stored energy in a single LHC sector is roughly the same as the kinetic energy of a passenger jet at cruising speed. The first new detector is designed to monitor the superconducting...

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80 + trademark Standard Design. This volume 9 discusses Electric Power and Auxiliary Systems

Lossless Coding Standards for Space Data Systems

Science.gov (United States)

Rice, R. F.

1996-01-01

The International Consultative Committee for Space Data Systems (CCSDS) is preparing to issue its first recommendation for a digital data compression standard. Because the space data systems of primary interest are employed to support scientific investigations requiring accurate representation, this initial standard will be restricted to lossless compression.

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80 + trademark Standard Design. This volume 10 discusses the Steam and Power Conversion System and Radioactive Waste Management

The Small Explorer Data System - A data system based on standard interfaces

Science.gov (United States)

Smith, Brian S.; Hengemihle, Jerome

1990-01-01

The Small Explorer Data System was developed by NASA Goddard Space Flight Center using a 'standard interfaces' approach. Standard interfaces make it adaptable to a wide variety of missions. The paper describes the Small Explorer Data System with particular emphasis on the standard interfaces incorporated in both the hardware and software.

7 CFR 3016.20 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Standards for financial management systems. 3016.20... Standards for financial management systems. (a) A State must expand and account for grant funds in... financial management systems of other grantees and subgrantees must meet the following standards: (1...

7 CFR 277.6 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Standards for financial management systems. 277.6... ADMINISTRATIVE COSTS OF STATE AGENCIES § 277.6 Standards for financial management systems. (a) General. This section prescribes standards for financial management systems in administering program funds by the State...

Standard-D hydrogen monitoring system, system design description

International Nuclear Information System (INIS)

Schneider, T.C.

1996-01-01

During most of the year, it is assumed that the vapor space in the 177 radioactive waste tanks on the Hanford Project site contain a uniform mixture of gases. Several of these waste tanks (currently twenty-five, 6 Double Shell Tanks and 19 Single Shell Tanks) were identified as having the potential for the buildup of gasses to a flammable level. An active ventilation system in the Double Shell Tanks and a passive ventilation system in the Single Shell Tanks provides a method of expelling gasses from the tanks. A gas release from a tank causes a temporary rise in the tank pressure, and a potential for increased concentration of hydrogen gas in the vapor space. The gas is released via the ventilation systems until a uniform gas mixture in the vapor space is once again achieved. The Standard Hydrogen Monitoring System (SHMS) is designed to monitor and quantify the percent hydrogen concentration during these potential gas releases. This document describes the design of the Standard-D Hydrogen Monitoring System, (SHMS-D) and its components as it differs from the original SHMS

29 CFR 97.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Standards for financial management systems. 97.20 Section 97... Standards for financial management systems. (a) A State must expand and account for grant funds in... financial management systems of other grantees and subgrantees must meet the following standards: (1...

Traceability system for radioactivity standards in Japan

International Nuclear Information System (INIS)

Hino, Yoshio

2000-01-01

The electrotechnical laboratory (ETL) is the one of the largest national research institute, affiliated with the Ministry of International Trade and Industry (MITI). The ETL has a role to maintain the national standards of electricity, acoustics, visible light, ionizing radiation and radioactivity. The primary radioactivity standards have been established in ETL mainly with the 4πβ-γ coincidence method. The liquid scintillation counters and multi-wire proportional counters are also used for pure-beta and surface emission rate standards, respectively. As for the traceability, the primary standard sources are transferred to the Japan Radio Isotope Association (JRIA), and the JRIA measure these sources to calibrate their secondary standard equipments such as high pressurized 4π ionization chambers, high pore Ge and Nal (Tl) gamma spectrometers. The primary sources are also sent to the BIPM and neighboring countries for the intercomparisons to keep the consistency of the national standards. In this paper, these measurement techniques for the primary standardization and transfer system will be introduced, and some results of comparisons for certificate the traceability system will be described. (author)

Nasa-wide Standard Administrative Systems

Science.gov (United States)

Schneck, P.

1984-01-01

Factors to be considered in developing agency-wide standard administrative systems for NASA include uniformity of hardware and software; centralization vs. decentralization; risk exposure; and models for software development.

Process Control System Cyber Security Standards - An Overview

Energy Technology Data Exchange (ETDEWEB)

Robert P. Evans; V Stanley Scown; Rolf Carlson; Shabbir Shamsuddin; George Shaw; Jeff Dagle; Paul W Oman; Jeannine Schmidt

2005-10-01

The use of cyber security standards can greatly assist in the protection of critical infrastructure by providing guidelines and requisite imperatives in the implementation of computer-controlled systems. These standards are most effective when the engineers and operators using the standards understand what each of the standards addresses and does not address. This paper provides a review and comparison of ten documents dealing with control system cyber security. It is not meant to be a complete treatment of all applicable standards; rather, this is an exemplary analysis showing the benefits of comparing and contrasting differing documents.

78 FR 59065 - Interview Room Recording System Standard and License Plate Reader Standard Workshops

Science.gov (United States)

2013-09-25

... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1632] Interview Room..., Department of Justice. ACTION: Notice of the Interview Room Recording System Standard and License Plate... performance standards for Interview Room Recording Systems and License Plate Readers used by criminal justice...

40 CFR 63.445 - Standards for the bleaching system.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Standards for the bleaching system. 63... Standards for Hazardous Air Pollutants from the Pulp and Paper Industry § 63.445 Standards for the bleaching system. (a) Each bleaching system that does not use any chlorine or chlorinated compounds for bleaching...

Specifications of Standards in Systems and Synthetic Biology.

Science.gov (United States)

Schreiber, Falk; Bader, Gary D; Golebiewski, Martin; Hucka, Michael; Kormeier, Benjamin; Le Novère, Nicolas; Myers, Chris; Nickerson, David; Sommer, Björn; Waltemath, Dagmar; Weise, Stephan

2015-09-04

Standards shape our everyday life. From nuts and bolts to electronic devices and technological processes, standardised products and processes are all around us. Standards have technological and economic benefits, such as making information exchange, production, and services more efficient. However, novel, innovative areas often either lack proper standards, or documents about standards in these areas are not available from a centralised platform or formal body (such as the International Standardisation Organisation). Systems and synthetic biology is a relatively novel area, and it is only in the last decade that the standardisation of data, information, and models related to systems and synthetic biology has become a community-wide effort. Several open standards have been established and are under continuous development as a community initiative. COMBINE, the ‘COmputational Modeling in BIology’ NEtwork has been established as an umbrella initiative to coordinate and promote the development of the various community standards and formats for computational models. There are yearly two meeting, HARMONY (Hackathons on Resources for Modeling in Biology), Hackathon-type meetings with a focus on development of the support for standards, and COMBINE forums, workshop-style events with oral presentations, discussion, poster, and breakout sessions for further developing the standards. For more information see http://co.mbine.org/. So far the different standards were published and made accessible through the standards’ web- pages or preprint services. The aim of this special issue is to provide a single, easily accessible and citable platform for the publication of standards in systems and synthetic biology. This special issue is intended to serve as a central access point to standards and related initiatives in systems and synthetic biology, it will be published annually to provide an opportunity for standard development groups to communicate updated specifications.

NASA's Earth Science Data Systems Standards Process Experiences

Science.gov (United States)

Ullman, Richard E.; Enloe, Yonsook

2007-01-01

NASA has impaneled several internal working groups to provide recommendations to NASA management on ways to evolve and improve Earth Science Data Systems. One of these working groups is the Standards Process Group (SPC). The SPG is drawn from NASA-funded Earth Science Data Systems stakeholders, and it directs a process of community review and evaluation of proposed NASA standards. The working group's goal is to promote interoperability and interuse of NASA Earth Science data through broader use of standards that have proven implementation and operational benefit to NASA Earth science by facilitating the NASA management endorsement of proposed standards. The SPC now has two years of experience with this approach to identification of standards. We will discuss real examples of the different types of candidate standards that have been proposed to NASA's Standards Process Group such as OPeNDAP's Data Access Protocol, the Hierarchical Data Format, and Open Geospatial Consortium's Web Map Server. Each of the three types of proposals requires a different sort of criteria for understanding the broad concepts of "proven implementation" and "operational benefit" in the context of NASA Earth Science data systems. We will discuss how our Standards Process has evolved with our experiences with the three candidate standards.

Standardization of detector control systems

International Nuclear Information System (INIS)

Fukunaga, Chikara

2000-01-01

Current and future detectors for high-energy and/or nuclear physics experiments require highly intelligent detector control systems. In order to reduce resources, the construction of a standardized template for the control systems based on the commercially available superviser control and data acquisition (SCADA) system has been proposed. The possibility of constructing this template is discussed and several key issues for evaluation of SCADA as the basis for such a template are presented. (author)

Session 2: Availability

CERN Document Server

Uythoven, J

2012-01-01

This session concentrated on the main players affecting the availability of the LHC: the Quench Protection System (QPS), the cryogenics system, the regularly foreseen technical stops and the effect of radiation on equipment failures. A forecast for operation in 2012 was made for all these items.

[Ciliate diversity and spatiotemporal variation in surface sediments of Yangtze River estuary hypoxic zone].

Science.gov (United States)

Feng, Zhao; Kui-Dong, Xu; Zhao-Cui, Meng

2012-12-01

By using denaturing gradient gel electrophoresis (DGGE) and sequencing as well as Ludox-QPS method, an investigation was made on the ciliate diversity and its spatiotemporal variation in the surface sediments at three sites of Yangtze River estuary hypoxic zone in April and August 2011. The ANOSIM analysis indicated that the ciliate diversity had significant difference among the sites (R = 0.896, P = 0.0001), but less difference among seasons (R = 0.043, P = 0.207). The sequencing of 18S rDNA DGGE bands revealed that the most predominant groups were planktonic Choreotrichia and Oligotrichia. The detection by Ludox-QPS method showed that the species number and abundance of active ciliates were maintained at a higher level, and increased by 2-5 times in summer, as compared with those in spring. Both the Ludox-QPS method and the DGGE technique detected that the ciliate diversity at the three sites had the similar variation trend, and the Ludox-QPS method detected that there was a significant variation in the ciliate species number and abundance between different seasons. The species number detected by Ludox-QPS method was higher than that detected by DGGE bands. Our study indicated that the ciliates in Yangtze River estuary hypoxic zone had higher diversity and abundance, with the potential to supply food for the polyps of jellyfish.

78 FR 44475 - Protection System Maintenance Reliability Standard

Science.gov (United States)

2013-07-24

... that the performance or product has some reliability-related value, then the requirement will have...] Protection System Maintenance Reliability Standard AGENCY: Federal Energy Regulatory Commission, Energy... Commission proposes to approve a revised Reliability Standard, PRC-005- 2--Protection System Maintenance, to...

76 FR 11518 - QPS Evaluation Services Inc.; Recognition as an NRTL

Science.gov (United States)

2011-03-02

... about its ownership that would qualify as a conflict under OSHA's independence policy. The amended... workplace. Consequently, if a test standard also covers any product for which OSHA does not require such...

Laser Pyro System Standardization and Man Rating

Science.gov (United States)

Brown, Christopher W.

2004-01-01

This viewgraph presentation reviews an X-38 laser pyro system standardization system designed for a new manned rated program. The plans to approve this laser initiation system and preliminary ideas for this system are also provided.

Standard interfaces for program-modular multiprocessor systems

International Nuclear Information System (INIS)

Chernykh, E.V.

1982-01-01

The peculiarities of the structures of existing and developed standard interfaces used in automation systems for nuclear physical experiments are considered. general structural characteristics of multiprocessor system interfaces are revealed. The comparison of the existing system CAMAC crate and designed standards of COMPEX, E3S and FASTBUS interfaces by capacity and relative cost is carried out. The analysis of the given data shows that operation of any interface is more advantageous at the rates close to capacity values, the relative cost being minimum. In this case the advantage is on the side of interfaces with greater capacity values for which at a moderated decrease of the exchange or requests processing rate the relative costs grow slower. A higher capacity of one-cycle exchange is provided with functional data way specialization in the interface. The conclusion is drawn that most perspective trend in the development of automation systems for high energy physics experiments is using FASTBUS standard

44 CFR 13.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Standards for financial... Standards for financial management systems. (a) A State must expand and account for grant funds in... financial management systems of other grantees and subgrantees must meet the following standards: (1...

Why We Should Establish a National System of Standards.

Science.gov (United States)

Hennen, Thomas J., Jr.

2000-01-01

Explains the need to establish a national system of standards for public libraries. Discusses local standards, state standards, and international standards, and suggests adopting a tiered approach including three levels: minimum standards; target standards; and benchmarking standards, as found in total quality management. (LRW)

10 CFR 600.311 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Standards for financial management systems. 600.311... Requirements § 600.311 Standards for financial management systems. (a) Recipients are encouraged to use existing financial management systems to the extent that the systems comply with Generally Accepted...

Research of radiation protection standard system in uranium mining and metallurgy

International Nuclear Information System (INIS)

Lian Guoxi; Song Liquan; Xie Zhanjun

2011-01-01

The contents of radiation and environment protection standards used in uranium mining and metallurgy are analyzed and the existent problems in current standard system are pointed out. A new standard system is established according to theory of systematology and the actuality of uranium mining and metallurgy. Some standard checklists which need to be complemented, corrected, deleted and used during the work of perfection and complementation of standard system are presented. The procedures of establishing new standard system are described, and some suggestions on the establishment and implementation of radiation protection standard system in uranium mining and metallurgy are put forward. (authors)

Standardization of Social Credit System Initiated in China

Institute of Scientific and Technical Information of China (English)

无

2004-01-01

@@ Introduction The current government advances that the order of market economy should be standardized and the social credit system of market economy in modern times should be established and completed. The social credit system should be formed on the basis of property right, supported by moral and high consciousness of social credit. Therefore, the basic framework and operation mechanism of the standards system for social credit will be established in 5 years in China in order to make standards play an important role in a regular market and the aspect of credit management, to improve administration's compliance with the regulation, and to facilitate the market economic order.

Emerging standards with application to accelerator safety systems

International Nuclear Information System (INIS)

Mahoney, K.L.; Robertson, H.P.

1997-01-01

This paper addresses international standards which can be applied to the requirements for accelerator personnel safety systems. Particular emphasis is given to standards which specify requirements for safety interlock systems which employ programmable electronic subsystems. The work draws on methodologies currently under development for the medical, process control, and nuclear industries

Implementation of standards within eLearning information systems

Directory of Open Access Journals (Sweden)

Roman Malo

2007-01-01

Full Text Available Nowadays, eLearning standards' support within eLearning systems is much discussed problem. In this problem domain especially the reference model SCORM must be considered. This de-facto standard is a package of common standards and specifications used for the standardization of eLearning activities as eLearning content preparation, using e-course, communication etc. Implementation of standards itself is a process with great difficulty and time requests. Interesting and considerable approach to this problem is dividing all the process into several standalone and isolated steps focused on the individual segments of standards. This concept, in the paper described as 4-tier model of eLearning standards’ implementation, principally based upon the SCORM model enables sequential implementation of support for standards of eLearning metadata, eLearning content and also communication and navigation in e-courses. This possibility leads to portability and independence of result e-content. Discuss concept is a framework for standardization within eLearning subsystem of University Information System at Mendel University in Brno.

49 CFR 19.21 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Standards for financial management systems. 19.21... ORGANIZATIONS Post-Award Requirements § 19.21 Standards for financial management systems. (a) Federal awarding... information whenever practical. (b) Recipients' financial management systems shall provide for the following...

34 CFR 74.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Standards for financial management systems. 74.21... Requirements Financial and Program Management § 74.21 Standards for financial management systems. (a... practical. (b) Recipients' financial management systems shall provide for the following: (1) Accurate...

22 CFR 145.21 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Standards for financial management systems. 145... Financial and Program Management § 145.21 Standards for financial management systems. (a) The Department... whenever practical. (b) Recipients' financial management systems shall provide for the following. (1...

43 CFR 12.921 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Standards for financial management systems... Organizations Post-Award Requirements § 12.921 Standards for financial management systems. (a) Federal awarding... information whenever practical. (b) Recipients' financial management systems shall provide for the following...

29 CFR 1470.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 29 Labor 4 2010-07-01 2010-07-01 false Standards for financial management systems. 1470.20 Section... Post-Award Requirements Financial Administration § 1470.20 Standards for financial management systems... the restrictions and prohibitions of applicable statutes. (b) The financial management systems of...

7 CFR 3019.21 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Standards for financial management systems. 3019.21... Requirements Financial and Program Management § 3019.21 Standards for financial management systems. (a) Federal... cost information whenever practical. (b) Recipients' financial management systems shall provide for the...

2 CFR 215.21 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Standards for financial management systems... Financial and Program Management § 215.21 Standards for financial management systems. (a) Federal awarding... information whenever practical. (b) Recipients' financial management systems shall provide for the following...

Safety standards of IAEA for management systems

International Nuclear Information System (INIS)

Vincze, P.

2005-01-01

IAEA has developed a new series of safety standards which are assigned for constitution of the conditions and which give the instruction for setting up the management systems that integrate the aims of safety, health, life environment and quality. The new standard shall replace IAEA 50-C-Q - Requirements for security of the quality for safety in nuclear power plants and other nuclear facilities as well as 14 related safety instructions mentioned in the Safety series No. 50-C/SG-Q (1996). When developing of this complex, integrated set of requirements for management systems, the IAEA requirements 50-C-Q (1996) were taken into consideration as well as the publications developed within the International organisation for standardization (ISO) ISO 9001:2000 and ISO14001: 1996. The experience of European Union member states during the development, implementation and improvement of the management systems were also taken into consideration

Instrumentation Standard Architectures for Future High Availability Control Systems

International Nuclear Information System (INIS)

Larsen, R.S.

2005-01-01

Architectures for next-generation modular instrumentation standards should aim to meet a requirement of High Availability, or robustness against system failure. This is particularly important for experiments both large and small mounted on production accelerators and light sources. New standards should be based on architectures that (1) are modular in both hardware and software for ease in repair and upgrade; (2) include inherent redundancy at internal module, module assembly and system levels; (3) include modern high speed serial inter-module communications with robust noise-immune protocols; and (4) include highly intelligent diagnostics and board-management subsystems that can predict impending failure and invoke evasive strategies. The simple design principles lead to fail-soft systems that can be applied to any type of electronics system, from modular instruments to large power supplies to pulsed power modulators to entire accelerator systems. The existing standards in use are briefly reviewed and compared against a new commercial standard which suggests a powerful model for future laboratory standard developments. The past successes of undertaking such projects through inter-laboratory engineering-physics collaborations will be briefly summarized

34 CFR 80.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Standards for financial management systems. 80.20... Financial Administration § 80.20 Standards for financial management systems. (a) A State must expand and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

20 CFR 437.20 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Standards for financial management systems... Financial Administration § 437.20 Standards for financial management systems. (a) A State must expend and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

32 CFR 32.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Standards for financial management systems. 32... Program Management § 32.21 Standards for financial management systems. (a) DoD Components shall require... unit cost information. (b) Recipients' financial management systems shall provide for the following. (1...

45 CFR 1183.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Standards for financial management systems. 1183... Financial Administration § 1183.20 Standards for financial management systems. (a) A State must expand and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

14 CFR 1260.121 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Standards for financial management systems... Requirements § 1260.121 Standards for financial management systems. (a) Recipients shall relate financial data...) Recipients' financial management systems shall provide for the following. (1) Accurate, current and complete...

22 CFR 135.20 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Standards for financial management systems. 135... Financial Administration § 135.20 Standards for financial management systems. (a) A State must expand and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

29 CFR 95.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Standards for financial management systems. 95.21 Section 95... Requirements Financial and Program Management § 95.21 Standards for financial management systems. (a... practical. (b) Recipients' financial management systems shall provide for the following: (1) Accurate...

45 CFR 74.21 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Standards for financial management systems. 74.21... Management § 74.21 Standards for financial management systems. (a) Recipients shall relate financial data to... cost information is usually not appropriate. (b) Recipients' financial management systems shall provide...

45 CFR 1174.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Standards for financial management systems. 1174... Financial Administration § 1174.20 Standards for financial management systems. (a) A State must expand and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

21 CFR 1403.20 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Standards for financial management systems. 1403... Financial Administration § 1403.20 Standards for financial management systems. (a) A State must expend and... of applicable statutes. (b) The financial management systems of other grantees and subgrantees must...

40 CFR 35.6270 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Standards for financial management... § 35.6270 Standards for financial management systems. (a) Accounting system standards—(1) General. The... of the adequacy of the financial management system as described in 40 CFR 31.20(c). (2) Allowable...

45 CFR 1157.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Standards for financial management systems. 1157... Administration § 1157.20 Standards for financial management systems. (a) A State must expand and account for... statutes. (b) The financial management systems of other grantees and subgrantees must meet the following...

32 CFR 33.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Standards for financial management systems. 33... financial management systems. (a) A State must expand and account for grant funds in accordance with State... management systems of other grantees and subgrantees must meet the following standards: (1) Financial...

75 FR 71625 - System Restoration Reliability Standards

Science.gov (United States)

2010-11-24

... to start operating and delivering electric power without assistance from the electric system... and system restoration and reporting following disturbances. \\3\\ North American Electric Reliability... Reliability Standards for the Bulk-Power System and determined that the proposed requirements are necessary to...

Implementation of standards within eLearning information systems

OpenAIRE

Roman Malo

2007-01-01

Nowadays, eLearning standards' support within eLearning systems is much discussed problem. In this problem domain especially the reference model SCORM must be considered. This de-facto standard is a package of common standards and specifications used for the standardization of eLearning activities as eLearning content preparation, using e-course, communication etc. Implementation of standards itself is a process with great difficulty and time requests. Interesting and considerable approach to...

49 CFR 18.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Standards for financial management systems. 18.20... Administration § 18.20 Standards for financial management systems. (a) A State must expand and account for grant... statutes. (b) The financial management systems of other grantees and subgrantees must meet the following...

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+trademark Standard Design. This Volume 18 provides Appendix B, Probabilistic Risk Assessment

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80 + trademark Standard Design. This volume 8 provides a description of instrumentation and controls

Standardization of penetrating radiation testing system

International Nuclear Information System (INIS)

Wiley, P.A.; Aronson, H.L.

1979-01-01

Standardization is provided to control system gain of a penetrating radiation testing system by periodically inspecting a reference object in the same manner as the product samples so as to generate a stabilization signal which is compared to a reference signal. The difference, if any, between the stabilization signal and the reference signal is integrated and the integrated signal is used to correct the gain of the system

System 80+trademark standard design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report has been prepared in support of the industry effort to standardize nuclear plant designs. The documents in this series describe the Combustion Engineering, Inc. System 80+ TM Standard Design

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80 + trademark Standard Design. This volume 11 discusses Radiation Protection, Conduct of Operations, and the Initial Test Program

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+trademark Standard Design. This Volume 16 details the application of Human Factors Engineering in the design process

75 FR 25137 - Changes to Standard Numbering System, Vessel Identification System, and Boating Accident Report...

Science.gov (United States)

2010-05-07

...-2003-14963] RIN 1625-AB45 Changes to Standard Numbering System, Vessel Identification System, and... System (SNS), the Vessel Identification System (VIS), and casualty reporting; require validation of... Standard Numbering System U.S.C. United States Code VIS Vessel Identification System III. Background Coast...

20 CFR 435.21 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Standards for financial management systems... ORGANIZATIONS, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Financial and Program Management § 435.21 Standards for financial management systems. (a) Introduction. SSA requires recipients to relate financial...

System 80+trademark Standard Design: CESSAR design certification

International Nuclear Information System (INIS)

1990-01-01

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describes the Combustion Engineering, Inc. System 80+trademark Standard Design. This Volume 17 provides Appendix A of this report, closure of unresolved and Genetic Safety Issues

State Standards and State Assessment Systems: A Guide to Alignment. Series on Standards and Assessments.

Science.gov (United States)

La Marca, Paul M.; Redfield, Doris; Winter, Phoebe C.

Alignment of content standards, performance standards, and assessments is crucial. This guide contains information to assist states and districts in aligning their assessment systems to their content and performance standards. It includes a review of current literature, both published and fugitive. The research is woven together with a few basic…

43 CFR 12.60 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Standards for financial management systems... AUDIT REQUIREMENTS AND COST PRINCIPLES FOR ASSISTANCE PROGRAMS Uniform Administrative Requirements for... Standards for financial management systems. (a) A State must expand and account for grant funds in...

32 CFR 34.11 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Standards for financial management systems. 34... ORGANIZATIONS Post-award Requirements Financial and Program Management § 34.11 Standards for financial management systems. (a) Recipients shall be allowed and encouraged to use existing financial management...

24 CFR 84.21 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Standards for financial management... and Program Management § 84.21 Standards for financial management systems. (a) HUD shall require.... (b) Recipients' financial management systems shall provide for the following: (1) Accurate, current...

45 CFR 2543.21 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Standards for financial management systems. 2543... OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 2543.21 Standards for financial management systems. (a) Federal awarding agencies shall require recipients to relate...

38 CFR 49.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... Program Management § 49.21 Standards for financial management systems. (a) Federal awarding agencies shall... practical. (b) Recipients' financial management systems shall provide for the following. (1) Accurate... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Standards for financial...

22 CFR 518.21 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Standards for financial management systems. 518... ORGANIZATIONS Post-Award Requirements Financial and Program Management § 518.21 Standards for financial management systems. (a) Federal awarding agencies shall require recipients to relate financial data to...

36 CFR 1210.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... Program Management § 1210.21 Standards for financial management systems. (a) The NHPRC shall require.... (b) Recipients' financial management systems shall provide for the following. (1) Accurate, current... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Standards for financial...

45 CFR 2541.200 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Standards for financial management systems. 2541... STATE AND LOCAL GOVERNMENTS Post-Award Requirements § 2541.200 Standards for financial management... violation of the restrictions and prohibitions of applicable statutes. (b) The financial management systems...

Patterns in Standards and Technologies for Economic Information Systems Interoperability

Directory of Open Access Journals (Sweden)

Vasile Irimia

2012-06-01

Full Text Available This paper presets results from a review of the current standards used for collaboration between economic information systems, including web services and service oriented architecture, EDI, ebXML framework, RosettaNet framework, cXML, xCBL UBL, BPMN, BPEL, WS-CDL, ASN.1, and others. Standards have a key role in promoting economic information system interoperability, and thus enable collaboration. Analyzing the current standards, technologies and applications used for economic information systems interoperability has revealed a common pattern that runs through all of them. From this pattern we construct a basic model of interoperability around which we relate and judge all standards, technologies and applications for economic information systems interoperability.

40 CFR 30.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Standards for financial management... Program Management § 30.21 Standards for financial management systems. (a) EPA shall require recipients to...) Recipients' financial management systems shall provide for the following. (1) Accurate, current and complete...

22 CFR 226.21 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Standards for financial management systems. 226... AWARDS TO U.S. NON-GOVERNMENTAL ORGANIZATIONS Post-award Requirements Financial and Program Management § 226.21 Standards for financial management systems. (a) Recipients shall relate financial data to...

Help for the Developers of Control System Cyber Security Standards

Energy Technology Data Exchange (ETDEWEB)

Robert P. Evans

2008-05-01

A Catalog of Control Systems Security: Recommendations for Standards Developers (Catalog), aimed at assisting organizations to facilitate the development and implementation of control system cyber security standards, has been developed. This catalog contains requirements that can help protect control systems from cyber attacks and can be applied to the Critical Infrastructures and Key Resources of the United States and other nations. The requirements contained in the catalog are a compilation of practices or various industry bodies used to increase the security of control systems from both physical and cyber attacks. They should be viewed as a collection of recommendations to be considered and judiciously employed, as appropriate, when reviewing and developing cyber security standards for control systems. The recommendations in the Catalog are intended to be broad enough to provide any industry using control systems the flexibility needed to develop sound cyber security standards specific to their individual security requirements.

24 CFR 85.20 - Standards for financial management systems.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Standards for financial management... Administration § 85.20 Standards for financial management systems. (a) A State must expand and account for grant... statutes. (b) The financial management systems of other grantees and subgrantees must meet the following...

Developing and enforcing internal information systems standards: InduMaker’s Standards Management Process

Directory of Open Access Journals (Sweden)

Claudia Loebbecke

2016-01-01

Full Text Available It is widely agreed that standards provide numerous benefits when available and enforced. Company-internal Information Systems (IS management procedures and solutions, in the following coined IS ‘standards’, allow for harmonizing operations between company units, locations and even different service providers. However, many companies lack an organized process for defining and managing internal IS standards, which causes uncertainties and delays in decision making, planning, and design processes. In this case study of the globally operating InduMaker (anonymized company name, an established manufacturing supplier, we look into the company-internal management of IS standards. Theoretically grounded in the organizational and IS-focused literature on business process modelling and business process commoditization, we describe and investigate InduMaker’s newly developed Standard Management Process (SMP for defining and managing company-internal business and IS standards, with which the multinational pursues offering clear answers to business and IT departments about existing IS standards, their degree of obligation, applicability, and scope at any time.

36 CFR 64.12 - Standards for grantee financial management systems.

Science.gov (United States)

2010-07-01

... financial management systems. 64.12 Section 64.12 Parks, Forests, and Public Property NATIONAL PARK SERVICE... RIGHTS-OF-WAY § 64.12 Standards for grantee financial management systems. The grantees' Financial Management Systems shall meet the minimum standards set forth in OMB Circular A-102, Attachment G. ...

Standards and guidelines applicable for the validation of programmable automation systems

International Nuclear Information System (INIS)

Haapanen, P.; Maskuniitty, M.

1993-02-01

The validation of programmable automation system for an application important to safety in a nuclear power plant requires a comprehensive view about the system quality and reliability. One central point is to get assured that proper international guidelines and standards have been followed in the design, construction and maintenance of the system. The study was directed to locate international standards and guidelines which can support the validation of programmable systems and to evaluate their applicability for the validation of systems on different levels of requirement during their life cycle. The publication reviews the most important international standards (IAEA, ISO, IEC, IEEE) and their basic principles both for system and application program. Several nuclear standards, which have drawn the main attention, and some general programmable automation standards have been examined. In addition one practical automation system has been examined in order to find essential questions. Based on these studies a set of important items for the qualification have been identified

The System 80+ Standard Plant design control document. Volume 23

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains part 16 References and Appendix 19 A Design Alternatives for section 19 (Probabilistic Risk Assessment) of the ADM Design and Analysis. Also covered is section 20 Unresolved Safety Issues of the ADM Design and Analysis. Finally sections 1--6 of the ADM Emergency Operations Guidelines are contained in this volume. Information covered in these sections include: standard post-trip actions; diagnostic actions; reactor trip recovery guideline; LOCA recovery; SG tube rupture recovery

CAMAC: a standardized modular instrumentation system

International Nuclear Information System (INIS)

Michot, Felicia

1978-01-01

In view of its modular aspect and its standardization at the international level, the CAMAC system appears as a very interesting system every time that there is a need for fastly constructing an experiment or a mounting in the laboratory or industry. As it can be connected to a computer interface CAMAC may be used for data acquisition, with machine-tools or for industrial process control. The operation mode of said system is discussed in the paper, together with its constituting elements and performance [fr

The System 80+ Standard Plant design control document. Volume 1

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume covers the DCD introduction and contains sections 1 and parts 1--7 of section 2 of the CDM. Parts 1--7 included the following: (2.1) Design of SSC; (2.2) Reactor; (2.3) RCS and connected systems; (2.4) Engineered Safety Features; (2.5) Instrumentation and Control; (2.6) Electric Power; and (2.7) Auxiliary Systems

The System 80+ Standard Plant design control document. Volume 19

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains five technical specification bases that are part of Appendix 16 A of the ADM Design and Analysis. They are: TS B3.3 Instrumentation Bases; TS B3.4 RCS Bases; TS B3.5 ECCS Bases; TS B3.6 Containment Systems Bases; and TS B3.7 Plant Systems Bases

European standards applied by Gas Transmission System Operator

International Nuclear Information System (INIS)

Witek, M.; Kuchta, K.; Oleszkiewicz, J.; Teperek, T.

2005-01-01

The lecture described actual state of implementation of European standards concerning transmission of natural gas and underlined their importance for proper performance of Transmission System Operator (TSO). European standards implemented to Polish Standards as PN-EN, necessary for TSO, related to design, construction and operation of high pressure gas network were also described. The lecture underlined as well the impact of standards application on preparation process of national regulations. They obligate TSO to create the technical conditions that ensure safety of gas transmission network functioning as well as environmental and surroundings safety. (authors)

The System 80+ Standard Plant design control document. Volume 11

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume covers parts 6 and 7 and appendix 7A for section 7 (Instrumentation and Control) of the ADM Design and Analysis. The topics covered by these are: other systems required for safety; control systems not required by safety; and CMF evaluation of limiting faults. Parts 1--3 of section 8 (Electric Power) of the ADM are also included in this volume. Topics covered by these parts are: introduction; offsite power system; and onsite power system

Referring to IAEA system to improve Chinese standards system on nuclear and radiation safety

International Nuclear Information System (INIS)

Shang Zhaorong; Wang Wenhai

2010-01-01

Referring to the standards system of IAEA, to build and improve the Chinese standards system of nuclear and radiation safety is a long term infrastructure work and an assurance to keep sustainable development of nuclear industry and nuclear technology application in China. The paper analyses the current main problem, and gives some suggestions on developing and improving the system. (authors)

Efficiency of Management Systems, Based on International Standards

Directory of Open Access Journals (Sweden)

Elena B. Gafforova

2012-03-01

Full Text Available The article considers major trends of management systems standardization development and efficiency. The authors determine possible structure of effects in the process of integrated management systems implementation.

The System 80+ Standard Plant design control document. Volume 10

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains Appendices 6A, 6B, and 6C for section 6 (Engineered Safety Features) of the ADM Design and Analysis. Also, parts 1--5 of section 7 (Instrumentation and Control) of the ADM Design and Analysis are covered. The following information is covered in these parts: introduction; reactor protection system; ESF actuation system; system required for safe shutdown; and safety-related display instrumentation

75 FR 35689 - System Personnel Training Reliability Standards

Science.gov (United States)

2010-06-23

... planning staff at control areas and reliability coordinators concerning power system characteristics and... Coordination--Staffing). \\11\\ Mandatory Reliability Standards for the Bulk-Power System, Order No. 693, Federal... American bulk electric system are competent to perform those reliability-related tasks.\\22\\ The proposed...

The System 80+ Standard Plant design control document. Volume 18

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains the following technical specifications of section 16 (Technical Specifications) of the ADM Design and Analysis: TS 3.3 Instrumentation; TS 3.4 Reactor Coolant System; TS 3.5 Emergency Core Cooling System; TS 3.6 Containment Systems; TS 3.7 Plant Systems; TS 3.8 Electrical Power Systems; TS 3.9 Refueling Operations; TS 4.0 Design Features; TS 5.0 Administrative Controls. Appendix 16 A Tech Spec Bases is also included. It contains the following: TS B2.0 Safety Limits Bases; TS B3.0 LCO Applicability Bases; TS B3.1 Reactivity Control Bases; TS B3.2 Power Distribution Bases

Hardware standardization for embedded systems

International Nuclear Information System (INIS)

Sharma, M.K.; Kalra, Mohit; Patil, M.B.; Mohanty, Ashutos; Ganesh, G.; Biswas, B.B.

2010-01-01

Reactor Control Division (RCnD) has been one of the main designers of safety and safety related systems for power reactors. These systems have been built using in-house developed hardware. Since the present set of hardware was designed long ago, a need was felt to design a new family of hardware boards. A Working Group on Electronics Hardware Standardization (WG-EHS) was formed with an objective to develop a family of boards, which is general purpose enough to meet the requirements of the system designers/end users. RCnD undertook the responsibility of design, fabrication and testing of boards for embedded systems. VME and a proprietary I/O bus were selected as the two system buses. The boards have been designed based on present day technology and components. The intelligence of these boards has been implemented on FPGA/CPLD using VHDL. This paper outlines the various boards that have been developed with a brief description. (author)

The System 80+ Standard Plant design control document. Volume 2

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume covers the following information of the CDM: (2.8) Steam and power conversion; (2.9) Radioactive waste management; (2.10) Tech Support Center; (2.11) Initial test program; (2.12) Human factors; and sections 3, 4, and 5. Also covered in this volume are parts 1--6 of section 1 (General Plant Description) of the ADM Design and Analysis

The System 80+ Standard Plant design control document. Volume 24

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains sections 7--11 of the ADM Emergency Operations Guidelines. Topics covered are: excess steam demand recovery; loss of all feedwater; loss of offsite power; station blackout recovery; and functional recovery guideline. Appendix A Severe Accident Management Guidelines and Appendix B Lower Mode Operational Guidelines are also included

The System 80+ Standard Plant design control document. Volume 21

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains parts 1--10 of section 19 (Probabilistic Risk Assessment) of the ADM Design and Analysis. Topics covered are: methodology; initiating event evaluation; accident sequence determination; data analysis; systems analysis; external events analysis; shutdown risk assessment; accident sequence quantification; and sensitivity analysis. Also included in this volume are Appendix 19.8A Shutdown Risk Assessment and Appendix A to Appendix 19.8A Request for Information

49 CFR 236.401 - Automatic block signal system and interlocking standards applicable to traffic control systems.

Science.gov (United States)

2010-10-01

... TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Traffic Control Systems Standards § 236.401 Automatic... 49 Transportation 4 2010-10-01 2010-10-01 false Automatic block signal system and interlocking standards applicable to traffic control systems. 236.401 Section 236.401 Transportation Other Regulations...

41 CFR 105-72.301 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Standards for financial... Management § 105-72.301 Standards for financial management systems. (a) Federal awarding agencies shall... practical. (b) Recipients' financial management systems shall provide for the following. (1) Accurate...

Standard-Cell, Open-Architecture Power Conversion Systems

National Research Council Canada - National Science Library

Boroyevich, D; Wang, F; Lee, F. C; Odendaal, W. G; Edwards, S

2005-01-01

...). This project was purposefully aimed to develop a standardized hierarchical design and analysis methodology for modular power electronics conversion systems using as basis the ISO/OSI seven-layer reference model...

76 FR 55825 - Federal Motor Vehicle Safety Standards, Child Restraint Systems

Science.gov (United States)

2011-09-09

... [Docket No. NHTSA-2011-0139] RIN 2127-AJ44 Federal Motor Vehicle Safety Standards, Child Restraint Systems..., amends a provision in Federal Motor Vehicle Safety Standard No. 213, ``Child restraint systems,'' that... provision: When a motor vehicle safety standard is in effect under this chapter, a State or a political...

OPPE, FPPE, QPS, and why the alphabet soup of physician assessment is essential for safer patient care.

Science.gov (United States)

Loftus, Michael L

Creating a successful quality and patient safety program requires a multifaceted approach that systematically reviews overall systems and processes, but also creates a standardized framework for evaluating individual practitioner performance on a routine basis. There are two required elements of competency assessment that are typically tied to the hospital credentialing process: ongoing professional practice evaluation (OPPE) and focused professional practice evaluation (FPPE). Each of these processes are mandated by the Joint Commission, and form an important cornerstone for ensuring adequate physician performance and knowledge base. Copyright © 2017. Published by Elsevier Inc.

75 FR 72664 - System Personnel Training Reliability Standards

Science.gov (United States)

2010-11-26

...--Staffing). \\2\\ Mandatory Reliability Standards for the Bulk-Power System, Order No. 693, 72 FR 16416 (Apr... on the North American bulk electric system are competent to perform those reliability-related tasks... PER-004-2 will achieve a significant improvement in the reliability of the Bulk- Power System and...

Control Systems Security Center Comparison Study of Industrial Control System Standards against the Control Systems Protection Framework Cyber-Security Requirements

Energy Technology Data Exchange (ETDEWEB)

Robert P. Evans

2005-09-01

Cyber security standards, guidelines, and best practices for control systems are critical requirements that have been delineated and formally recognized by industry and government entities. Cyber security standards provide a common language within the industrial control system community, both national and international, to facilitate understanding of security awareness issues but, ultimately, they are intended to strengthen cyber security for control systems. This study and the preliminary findings outlined in this report are an initial attempt by the Control Systems Security Center (CSSC) Standard Awareness Team to better understand how existing and emerging industry standards, guidelines, and best practices address cyber security for industrial control systems. The Standard Awareness Team comprised subject matter experts in control systems and cyber security technologies and standards from several Department of Energy (DOE) National Laboratories, including Argonne National Laboratory, Idaho National Laboratory, Pacific Northwest National Laboratory, and Sandia National Laboratories. This study was conducted in two parts: a standard identification effort and a comparison analysis effort. During the standard identification effort, the Standard Awareness Team conducted a comprehensive open-source survey of existing control systems security standards, regulations, and guidelines in several of the critical infrastructure (CI) sectors, including the telecommunication, water, chemical, energy (electric power, petroleum and oil, natural gas), and transportation--rail sectors and sub-sectors. During the comparison analysis effort, the team compared the requirements contained in selected, identified, industry standards with the cyber security requirements in ''Cyber Security Protection Framework'', Version 0.9 (hereafter referred to as the ''Framework''). For each of the seven sector/sub-sectors listed above, one standard was

Assessment of Safety Standards for Automotive Electronic Control Systems

Science.gov (United States)

2016-06-01

This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

Future Standardization of Space Telecommunications Radio System with Core Flight System

Science.gov (United States)

Briones, Janette C.; Hickey, Joseph P.; Roche, Rigoberto; Handler, Louis M.; Hall, Charles S.

2016-01-01

NASA Glenn Research Center (GRC) is integrating the NASA Space Telecommunications Radio System (STRS) Standard with the Core Flight System (cFS), an avionics software operating environment. The STRS standard provides a common, consistent framework to develop, qualify, operate and maintain complex, reconfigurable and reprogrammable radio systems. The cFS is a flexible, open architecture that features a plugand- play software executive called the Core Flight Executive (cFE), a reusable library of software components for flight and space missions and an integrated tool suite. Together, STRS and cFS create a development environment that allows for STRS compliant applications to reference the STRS application programmer interfaces (APIs) that use the cFS infrastructure. These APIs are used to standardize the communication protocols on NASAs space SDRs. The cFS-STRS Operating Environment (OE) is a portable cFS library, which adds the ability to run STRS applications on existing cFS platforms. The purpose of this paper is to discuss the cFS-STRS OE prototype, preliminary experimental results performed using the Advanced Space Radio Platform (ASRP), the GRC S- band Ground Station and the SCaN (Space Communication and Navigation) Testbed currently flying onboard the International Space Station (ISS). Additionally, this paper presents a demonstration of the Consultative Committee for Space Data Systems (CCSDS) Spacecraft Onboard Interface Services (SOIS) using electronic data sheets (EDS) inside cFE. This configuration allows for the data sheets to specify binary formats for data exchange between STRS applications. The integration of STRS with cFS leverages mission-proven platform functions and mitigates barriers to integration with future missions. This reduces flight software development time and the costs of software-defined radio (SDR) platforms. Furthermore, the combined benefits of STRS standardization with the flexibility of cFS provide an effective, reliable and

The System 80+ Standard Plant design control document. Volume 20

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains 2 technical specifications bases as part of Appendix 16 A Tech Spec Bases. They are TS B3.8 Electrical Power Technical Systems Bases and TS B3.9 Refueling Operations Bases. All 3 parts of section 17 (QA) and all 10 parts of section 18 (Human Factors) of the ADM Design and Analysis are contained in this volume. Topics covered in section 17 are: design phase QA; operations phase QA; and design phase reliability assurance. Topics covered by section 18 are: design team organization; design goals; design process; functional task analysis; control room configuration; information presentation; control and monitoring; verification and validation; and review documents

Communication Standards Suitable for MES Systems Designed for SMES

Directory of Open Access Journals (Sweden)

Ondřej WINKLER

2009-06-01

Full Text Available A MES (Manufacturing Execution System is a system that large companies use to measure or control critical production activities. Individual parts of this system can be used as a model for development of tools suitable for small and medium enterprises (SMEs. It can demonstrate how manufacturing systems works and which communication standards are usable. The communication standards enable data acquisition, data processing, storing and their conversion for any production report. Furthermore, interfaces for web clients allow displaying the raw or transformed data as a text or a graphic chart. The development of tools for an access to the data retrieved from MES software is described in this paper.

75 FR 15620 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2010-03-30

... fully develop improved brake systems and also to ensure vehicle control and stability while braking... [Docket No. NHTSA 2009-0175] RIN 2127-AK62 Federal Motor Vehicle Safety Standards; Air Brake Systems... Federal motor vehicle safety standard for air brake systems by requiring substantial improvements in...

78 FR 9623 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2013-02-11

... initial speeds, vehicle manufacturers will need to develop unique or complicated braking systems to comply... [Docket No. NHTSA-2013-0011] RIN 2127-AL11 Federal Motor Vehicle Safety Standards; Air Brake Systems... rule that amended the Federal motor vehicle safety standard for air brake systems by requiring...

77 FR 22637 - Federal Motor Vehicle Safety Standards; Accelerator Control Systems

Science.gov (United States)

2012-04-16

... revise the Federal Motor Vehicle Safety Standard for accelerator control systems (ACS) in two ways. First... Standard (FMVSS) No. 124, Accelerator Control Systems,\\2\\ in two ways. First, we are proposing to update... February 2011 final report ``Technical Assessment of Toyota Electronic Throttle Control Systems,'' the...

78 FR 73112 - Monitoring System Conditions-Transmission Operations Reliability Standards; Interconnection...

Science.gov (United States)

2013-12-05

...\\ \\8\\ Mandatory Reliability Standards for the Bulk-Power System, Order No. 693, 72 FR 16416 (Apr. 4... operators and reliability coordinators to ``plan and operate the interconnected Bulk Electric System in a... mandated in the currently- effective standards, thereby improving reliability of the bulk power system...

Standard Procurement System Use and User Satisfaction

National Research Council Canada - National Science Library

2001-01-01

The audit was performed in response to concerns expressed by the Chairman, House of Representatives Committee on Budget that DoD was not effectively spending Federal funds to acquire the Standard Procurement System (SPS...

The System 80+ Standard Plant design control document. Volume 15

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains all five parts of section 12 (Radiation Protection) of the ADM Design and Analysis. Topics covered are: ALARA exposures; radiation sources; radiation protection; dose assessment; and health physics program. All six parts and appendices A and B for section 13 (Conduct of Operations) of the ADM Design and Analysis are also contained in this volume. Topics covered are: organizational structure; training program; emergency planning; review and audit; plant procedures; industrial security; sabotage protection (App 13A); and vital equipment list (App 13B)

The System 80+ Standard Plant design control document. Volume 17

International Nuclear Information System (INIS)

1997-01-01

This Design Control Document (DCD) is a repository of information comprising the System 80+trademark Standard Plant Design. The DCD also provides that design-related information to be incorporated by reference in the design certification rule for the System 80+ Standard Plant Design. Applicants for a combined license pursuant to 10 CFR 52 must ensure that the final Design Certification Rule and the associated Statements of Consideration are used when making all licensing decisions relevant to the System 80+ Standard Plant Design. The Design Control Document contains the DCD introduction, The Certified Design Material (CDM) [i.e., ''Tier 1''] and the Approved Design Material (ADM) [i.e., ''Tier 2''] for the System 80+ Standard Plant Design. The CDM includes the following sections: (1) Introductory material; (2) Certified Design Material for System 80+ systems and structures; (3) Certified Design Material for non-system-based aspects of the System 80+ Certified design; (4) Interface requirements; and (5) Site parameters. The ADM, to the extent applicable for the System 80+ Standard Plant Design, includes: (1) the information required for the final safety analysis report under 20 CFR 50.34; (2) other relevant information required by 10 CFR 52.47; and (3) emergency operations guidelines. This volume contains parts 2-7 and appendix 15A for section 15 (Accident Analysis) of the ADM Design and Analysis. Topics covered in these parts are: decrease in heat removal; decrease in RCS flow rate; power distribution anomalies; increase in RCS inventory; decrease in RCS inventory; release of radioactive materials. The appendix covers radiological release models. Also contained here are five technical specifications for section 16 (Technical Specifications) of the ADM Design and Analysis. They are: TS 1.0 Use and Applications; TS 2.0 Safety Limits; TS 3.0 LCO Availability; TS 3.1 Reactivity Control; and TS 3.2 Power Distribution

Practices around Customization of Standard Systems

DEFF Research Database (Denmark)

Dittrich, Yvonne; Vaucouleur, Sebastien

2008-01-01

More and more software systems are developed by customizing a standard product that provide the major part of the functionality. The customization of Enterprise Resource Planning systems is such a product based software development practice. Little empirical research on the specificities...... of these software development practices is available. We present an empirical study on customization practices based on video recordings, interviews and a survey. The observed and reported practices challenge some of the principles of software engineering. Based on the analysis, we discuss the specificity...

A passive on-chip, superconducting circulator using rings of tunnel junctions

OpenAIRE

Müller, Clemens; Guan, Shengwei; Vogt, Nicolas; Cole, Jared H.; Stace, Thomas M.

2017-01-01

We present the design of a passive, on-chip microwave circulator based on a ring of superconducting tunnel junctions. We investigate two distinct physical realisations, based on either Josephson junctions (JJ) or quantum phase slip elements (QPS), with microwave ports coupled either capacitively (JJ) or inductively (QPS) to the ring structure. A constant bias applied to the center of the ring provides the symmetry breaking (effective) magnetic field, and no microwave or rf bias is required. W...

76 FR 44829 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2011-07-27

... [Docket No. NHTSA-2009-0175] RIN 2127-AK84 Federal Motor Vehicle Safety Standards; Air Brake Systems... final rule that amended the Federal motor vehicle safety standard for air brake systems by requiring... between Bendix Commercial Vehicle Systems and Dana Corporation; and ArvinMeritor. The agency received four...

Junctionless Cooper pair transistor

Energy Technology Data Exchange (ETDEWEB)

Arutyunov, K. Yu., E-mail: konstantin.yu.arutyunov@jyu.fi [National Research University Higher School of Economics , Moscow Institute of Electronics and Mathematics, 101000 Moscow (Russian Federation); P.L. Kapitza Institute for Physical Problems RAS , Moscow 119334 (Russian Federation); Lehtinen, J.S. [VTT Technical Research Centre of Finland Ltd., Centre for Metrology MIKES, P.O. Box 1000, FI-02044 VTT (Finland)

2017-02-15

Highlights: • Junctionless Cooper pair box. • Quantum phase slips. • Coulomb blockade and gate modulation of the Coulomb gap. - Abstract: Quantum phase slip (QPS) is the topological singularity of the complex order parameter of a quasi-one-dimensional superconductor: momentary zeroing of the modulus and simultaneous 'slip' of the phase by ±2π. The QPS event(s) are the dynamic equivalent of tunneling through a conventional Josephson junction containing static in space and time weak link(s). Here we demonstrate the operation of a superconducting single electron transistor (Cooper pair transistor) without any tunnel junctions. Instead a pair of thin superconducting titanium wires in QPS regime was used. The current–voltage characteristics demonstrate the clear Coulomb blockade with magnitude of the Coulomb gap modulated by the gate potential. The Coulomb blockade disappears above the critical temperature, and at low temperatures can be suppressed by strong magnetic field.

TDA Assessment of Recommendations for Space Data System Standards

Science.gov (United States)

Posner, E. C.; Stevens, R.

1984-01-01

NASA is participating in the development of international standards for space data systems. Recommendations for standards thus far developed are assessed. The proposed standards for telemetry coding and packet telemetry provide worthwhile benefit to the DSN; their cost impact to the DSN should be small. Because of their advantage to the NASA space exploration program, their adoption should be supported by TDA, JPL, and OSTDS.

PROWAY - a standard for distributed control systems

International Nuclear Information System (INIS)

Gellie, R.W.

1980-01-01

The availability of cheap and powerful microcomputer and data communications equipment has led to a major revision of instrumentation and control systems. Intelligent devices can now be used and distributed about the control system in a systematic and economic manner. These sub-units are linked by a communications system to provide a total system capable of meeting the required plant objectives. PROWAY, an international standard process data highway for interconnecting processing units in distributed industrial process control systems, is currently being developed. This paper describes the salient features and current status of the PROWAY effort. (auth)

New international and national standards concerning quality systems

International Nuclear Information System (INIS)

Petrick, K.; Reihlen, H.

1987-01-01

The history and contents of the latest standards DIN ISO 9000 through DIN ISO 9004 concerning quality systems are outlined. Information is given referring to the establishment of an in-house quality system, and to quality assurance requirements put down in a three-step quality assurance system for contractual purposes. The services available for certification of quality systems by the 'DQS' and legal aspects are mentioned. (HP)

28 CFR 70.21 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Standards for financial management..., HOSPITALS AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Financial and Program Management § 70.21 Standards for financial management systems. (a) Recipients must relate financial data to...

Standard-B Hydrogen Monitoring System, system design description

International Nuclear Information System (INIS)

Schneider, T.C.

1995-01-01

During most of the year, it is assumed that the vapor in the 177 radioactive waste tanks on the Hanford Project site contain a uniform mixture of gases. Several of these waste tanks (currently twenty five, 6 Double Shell Tanks and 19 Single Shell Tanks) were identified as having the potential for the buildup of gases to a flammable level. An active ventilation system in the Double Shell Tanks and a passive ventilation system in the Single Shell Tanks provides a method of expelling gases from the tanks. A gas release from a tank causes a temporary rise in the tank pressure, and a potential for increased concentration of hydrogen gas in the vapor space. The gas is released via the ventilation systems until a uniform gas mixture in the vapor space is once again achieved. This document describes the design of the Standard-B Hydrogen Monitoring System, (SHMS) and its components as it differs from the original SHMS. The differences are derived from changes made to improve the system performance but not implemented in all the installed enclosures

15 CFR 14.21 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Standards for financial management...-PROFIT, AND COMMERCIAL ORGANIZATIONS Post-Award Requirements Financial and Program Management § 14.21 Standards for financial management systems. (a) The Grants Officer shall require recipients to relate...

Measurements of Positronium Formation Cross Sections for Positron-Kr, Xe Scattering

Science.gov (United States)

Kauppila, W. E.; Kwan, C. K.; Li, H.; Stein, T. S.; Zhou, S.

1997-04-01

Our experimental approach(S. Zhou et al., Phys. Rev. Lett. 73, 236 (1994).) for measuring Ps formation cross sections (Q_Ps) involves passing a variable energy positron beam through a gas scattering cell and detecting the 511 keV annihilation gamma rays resulting from the decay of para-Ps and from the interaction of ortho-Ps with the walls of the scattering cell. It is found that the Q_Ps curves for both Kr and Xe rise rapidly from their formation threshold energies of 7.2 and 5.3 eV, reach maxima within about 10 eV of their thresholds and then decrease to become rather small (less than 10% of the peak heights) above 100 eV. At the maxima Q_Ps accounts for more than 50% of the total scattering cross sections. There is some evidence of possible small scale structure in the Q_Ps curves between 10 and 100 eV. The present results are consistent with the prior measurements of Diana et al.( L.M. Diana et al., in "Atomic Physics with Positrons", edited by J.W. Humberston and E.A.G. Armour (Plenum, New York and London, 1987), p. 55; and in "Positron Annihilation", edited by L. Dorikens-Vanpraet et al. (World Scientific, Singapore, 1989), p. 311.) from near threshold to 70 eV for Kr and from 15 to 100 eV for Xe.

Engineering aspects of compact stellarators

International Nuclear Information System (INIS)

Nelson, B.E.; Benson, R.D.; Brooks, A.

2003-01-01

Compact stellarators could combine the good confinement and high beta of a tokamak with the inherently steady state, disruption-free characteristics of a stellarator. Two U.S. compact stellarator facilities are now in the conceptual design phase: the National Compact Stellarator Experiment (NCSX) and the Quasi- Poloidal Stellarator (QPS). NCSX has a major radius of 1.4 m and a toroidal field up to 2 T. The primary feature of both NCSX and QPS is the set of modular coils that provide the basic magnetic configuration. These coils represent a major engineering challenge due to the complex shape, precise geometric accuracy, and high current density of the windings. The winding geometry is too complex for conventional hollow copper conductor construction. Instead, the modular coils will be wound with flexible, multi strand cable conductor that has been compacted to a 75% copper packing fraction. Inside the NCSX coil set and surrounding the plasma is a highly contoured vacuum vessel. The vessel consists of three identical, 120 deg. segments that are bolted together at double sealed joints. The QPS device has a major radius of 0.9 m, a toroidal field of 1 T, and an aspect ratio of only 2.7. Instead of an internal vacuum vessel, the QPS modular coils will operate in an external vacuum tank. (author)

Fundamental Data Standards for Science Data System Interoperability and Data Correlation

Science.gov (United States)

Hughes, J. Steven; Gopala Krishna, Barla; Rye, Elizabeth; Crichton, Daniel

The advent of the Web and languages such as XML have brought an explosion of online science data repositories and the promises of correlated data and interoperable systems. However there have been relatively few successes in meeting the expectations of science users in the internet age. For example a Google-like search for images of Mars will return many highly-derived and appropriately tagged images but largely ignore the majority of images in most online image repositories. Once retrieved, users are further frustrated by poor data descriptions, arcane formats, and badly organized ancillary information. A wealth of research indicates that shared information models are needed to enable system interoperability and data correlation. However, at a more fundamental level, data correlation and system interoperability are dependant on a relatively few shared data standards. A com-mon data dictionary standard, for example, allows the controlled vocabulary used in a science repository to be shared with potential collaborators. Common data registry and product iden-tification standards enable systems to efficiently find, locate, and retrieve data products and their metadata from remote repositories. Information content standards define categories of descriptive data that help make the data products scientifically useful to users who were not part of the original team that produced the data. The Planetary Data System (PDS) has a plan to move the PDS to a fully online, federated system. This plan addresses new demands on the system including increasing data volume, numbers of missions, and complexity of missions. A key component of this plan is the upgrade of the PDS Data Standards. The adoption of the core PDS data standards by the International Planetary Data Alliance (IPDA) adds the element of international cooperation to the plan. This presentation will provide an overview of the fundamental data standards being adopted by the PDS that transcend science domains and that

System 80+{trademark} Standard Design: CESSAR design certification. Volume 9: Amendment I

Energy Technology Data Exchange (ETDEWEB)

1990-12-21

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 9 discusses Electric Power and Auxiliary Systems.

NASA/NBS (National Aeronautics and Space Administration/National Bureau of Standards) standard reference model for telerobot control system architecture (NASREM)

Science.gov (United States)

Albus, James S.; Mccain, Harry G.; Lumia, Ronald

1989-01-01

The document describes the NASA Standard Reference Model (NASREM) Architecture for the Space Station Telerobot Control System. It defines the functional requirements and high level specifications of the control system for the NASA space Station document for the functional specification, and a guideline for the development of the control system architecture, of the 10C Flight Telerobot Servicer. The NASREM telerobot control system architecture defines a set of standard modules and interfaces which facilitates software design, development, validation, and test, and make possible the integration of telerobotics software from a wide variety of sources. Standard interfaces also provide the software hooks necessary to incrementally upgrade future Flight Telerobot Systems as new capabilities develop in computer science, robotics, and autonomous system control.

USL/DBMS NASA/PC R and D project system testing standards

Science.gov (United States)

Dominick, Wayne D. (Editor); Kavi, Srinu; Moreau, Dennis R.; Yan, Lin

1984-01-01

A set of system testing standards to be used in the development of all C software within the NASA/PC Research and Development Project is established. Testing will be considered in two phases: the program testing phase and the system testing phase. The objective of these standards is to provide guidelines for the planning and conduct of program and software system testing.

Understanding information retrieval systems management, types, and standards

CERN Document Server

Bates, Marcia J

2011-01-01

In order to be effective for their users, information retrieval (IR) systems should be adapted to the specific needs of particular environments. The huge and growing array of types of information retrieval systems in use today is on display in Understanding Information Retrieval Systems: Management, Types, and Standards, which addresses over 20 types of IR systems. These various system types, in turn, present both technical and management challenges, which are also addressed in this volume. In order to be interoperable in a networked environment, IR systems must be able to use various types of

The LHC enters a new phase

CERN Document Server

CERN Bulletin

2010-01-01

After achieving the world record energy of 1.18 TeV per proton beam last November, the LHC is now preparing for higher energy and luminosity.   The teams are working in the tunnel to improve the electrical reliability of the magnet protection system.   Before the 2009 running period began, all the necessary preparations to run the LHC at the collision energy of 1.18 TeV per beam had been carried out. The goal of the technical stop, which will end mid-February, is to prepare the machine for running at 3.5 TeV per beam. In order to achieve that, a current as high as 6 kAmps will have to flow into the LHC magnets. The main work is taking place on the new quench protection system (nQPS) where teams are improving the electrical reliability of the connection between the Instrumentation Feedthrough Systems (IFS) on the magnets and the nQPS equipment. There are around 500 of these connectors for each of the eight sectors in the LHC that need to be repaired. These operations are necessary to en...

10 CFR 600.121 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Standards for financial management systems. 600.121... financial management systems. (a) Recipients shall relate financial data to performance data and develop....121(f) and 600.181, recipients' financial management systems shall provide for the following: (1...

36 CFR 1207.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... financial management systems. (a) A State must expand and account for grant funds in accordance with State... management systems of other grantees and subgrantees must meet the following standards: (1) Financial... the financial management system of any applicant for financial assistance as part of a preaward review...

40 CFR 35.6550 - Procurement system standards.

Science.gov (United States)

2010-07-01

... referred to the local, State, Tribal, or Federal authority having proper jurisdiction. (5) Selection... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Procurement system standards. 35.6550... ASSISTANCE STATE AND LOCAL ASSISTANCE Cooperative Agreements and Superfund State Contracts for Superfund...

Using ISO 25040 standard for evaluating electronic health record systems.

Science.gov (United States)

Oliveira, Marília; Novaes, Magdala; Vasconcelos, Alexandre

2013-01-01

Quality of electronic health record systems (EHR-S) is one of the key points in the discussion about the safe use of this kind of system. It stimulates creation of technical standards and certifications in order to establish the minimum requirements expected for these systems. [1] In other side, EHR-S suppliers need to invest in evaluation of their products to provide systems according to these requirements. This work presents a proposal of use ISO 25040 standard, which focuses on the evaluation of software products, for define a model of evaluation of EHR-S in relation to Brazilian Certification for Electronic Health Record Systems - SBIS-CFM Certification. Proposal instantiates the process described in ISO 25040 standard using the set of requirements that is scope of the Brazilian certification. As first results, this research has produced an evaluation model and a scale for classify an EHR-S about its compliance level in relation to certification. This work in progress is part for the acquisition of the degree of master in Computer Science at the Federal University of Pernambuco.

IAEA Safety Standards on Management Systems and Safety Culture

International Nuclear Information System (INIS)

Persson, Kerstin Dahlgren

2007-01-01

The IAEA has developed a new set of Safety Standard for applying an integrated Management System for facilities and activities. The objective of the new Safety Standards is to define requirements and provide guidance for establishing, implementing, assessing and continually improving a Management System that integrates safety, health, environmental, security, quality and economic related elements to ensure that safety is properly taken into account in all the activities of an organization. With an integrated approach to management system it is also necessary to include the aspect of culture, where the organizational culture and safety culture is seen as crucial elements of the successful implementation of this management system and the attainment of all the goals and particularly the safety goals of the organization. The IAEA has developed a set of service aimed at assisting it's Member States in establishing. Implementing, assessing and continually improving an integrated management system. (author)

Review international standards for grid connected photovoltaic systems in Malaysia

International Nuclear Information System (INIS)

Mekhilef, S.; Rahim, N.A.

2006-01-01

Grid connected PV is being applied on variety application including large centralised stations, commercial building and individual houses. There is a need for specific standard to address distinctive new issue created by grid connected PV power system. Internationally many countries are attempting to develop standards for building integration, Dc side issues and grid connection issues. This paper surveys the current development state of the major countries standards in this area, comparing and contrasting, standards and guideline under development, also addressing the need of standards for grid connected in Malaysia

Embedded Web Technology: Applying World Wide Web Standards to Embedded Systems

Science.gov (United States)

Ponyik, Joseph G.; York, David W.

2002-01-01

Embedded Systems have traditionally been developed in a highly customized manner. The user interface hardware and software along with the interface to the embedded system are typically unique to the system for which they are built, resulting in extra cost to the system in terms of development time and maintenance effort. World Wide Web standards have been developed in the passed ten years with the goal of allowing servers and clients to intemperate seamlessly. The client and server systems can consist of differing hardware and software platforms but the World Wide Web standards allow them to interface without knowing about the details of system at the other end of the interface. Embedded Web Technology is the merging of Embedded Systems with the World Wide Web. Embedded Web Technology decreases the cost of developing and maintaining the user interface by allowing the user to interface to the embedded system through a web browser running on a standard personal computer. Embedded Web Technology can also be used to simplify an Embedded System's internal network.

System 80+{trademark} Standard Design: CESSAR design certification. Volume 3: Amendment I

Energy Technology Data Exchange (ETDEWEB)

1990-12-21

This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+{sup TM} Standard Design. This report, Volume 3, in conjunction with Volume 2, provides the design of structures, components, equipment and systems.

Bus bar joints stability and protection

CERN Document Server

Verweij, A

2009-01-01

A defective bus connection between two dipole magnets was the primary cause of the incident in sector 34 on September 19th. I will show how this could have happened, i.e. how a highly resistive joint has caused a thermal runaway and burned (or opened) before the QPS threshold was reached. In the second part of the talk I will present the new detection limits for the QPS upgrade of the RB and RQ circuits, required to avoid similar thermal runaways in the future.

Standardized and modular microfluidic platform for fast lab on chip system development

NARCIS (Netherlands)

Dekker, Stefan; van den Berg, Albert; Odijk, Mathieu; Lee, Abraham; DeVoe, Don

2017-01-01

This paper reports a modular microfluidic system with standardized parts, enabling rapid prototyping of lab on chip systems. Herewith contributing to the technology transfer from academy to industry. The use of standardized parts also makes it possible to design a microfluidic systems in a top down

Development of the module inspection system for new standardized radiation monitoring modules

International Nuclear Information System (INIS)

Furukawa, Masami; Shimizu, Kazuaki; Hiruta, Toshihito; Mizugaki, Toshio; Ohi, Yoshihiro; Chida, Tooru.

1994-10-01

This report mentions about the module inspection system which does the maintenance check of the monitoring modules adapted the new monitoring standard, as well as the result of the verification of the modules. The module inspection system is the automatic measurement system with the computer. The system can perform the functional and the characteristic examination of the monitoring modules, the calibration with radiation source and inspection report. In the verification of the monitoring module, three major items were tested, the adaptability for the new monitoring standard, the module functions and each characteristics. All items met the new monitoring standard. (author)

Development of standard practice guidelines for open and closed system suctioning.

Science.gov (United States)

Özden, Dilek; Görgülü, R Selma

2012-05-01

This study was carried out to determine the knowledge and practice of nurses before and after training and the development of standard practice guidelines for open and closed system suctioning methods in patients with endotracheal tubes. Many life-threatening complications can occur when a suctioning procedure is not performed with the correct technique. It has been reported that standard practice guidelines for suctioning are insufficient in clinical practice. Non-participant structured observational study. We assessed a total of 48 nurses who were employed in the cardiovascular surgery intensive care unit of a state hospital in Turkey. We used a questionnaire and nurse observation forms to assess the use of the open and closed system suctioning. There was a significant difference between the mean scores of the answers ('true', 'wrong' and 'I do not know') for the use of open and closed system suctioning before and after training. In addition, all steps of both suctioning procedures were carried out correctly during the third observation. The compliance of the nurses to the standard practice guidelines for open and closed suctioning and their knowledge levels on the subject were increased after training, while the implementation of standards was satisfactory. The development of open and closed system suctioning standard practice guidelines directly contributed to the enhancement of patient safety and the quality of nursing care. It is suggested that, as in other nursing care practices, suctioning should be carried out in accordance with standard practice guidelines, and health institutions should develop their standard practice guidelines and work in accordance with them. © 2012 Blackwell Publishing Ltd.

Design and implementation of a standard framework for KSTAR control system

International Nuclear Information System (INIS)

Lee, Woongryol; Park, Mikyung; Lee, Taegu; Lee, Sangil; Yun, Sangwon; Park, Jinseop; Park, Kaprai

2014-01-01

Highlights: • We performed a standardized of control system in KSTAR. • EPICS based software framework is developed for the realization of various control systems. • The applicability of the framework is widened from a simple command dispatcher to the real time application. • Our framework supports the implementation of embedded IOC in FPGA board. - Abstract: Standardization of control system is an important issue in KSTAR which is organized with various heterogeneous systems. Diverse control systems in KSTAR have been adopting new application software since 2010. Development of this software was launched for easy implementation of a data acquisition system but it is extended to as a Standard Framework (SFW) of control system in KSTAR. It is composed with a single library, database, template, and descriptor files. The SFW based controller has common factors. It has non-blocking control command method with a thread. The internal sequence handler makes it can be synchronized with KSTAR experiment. It also has a ring buffer pool mechanism for streaming input data handling. Recently, there are two important functional improvements in the framework. Processor embedded FPGA was proposed as a standard hardware platform for specific application. These are also manipulated by the SFW based embedded application. This approach gives single board system an ability of low level distributed control under the EPICS environments. We also developed a real time monitoring system as a real time network inspection tool in 2012 campaign using the SFW

System 80+{trademark} standard design incorporates radiation protection lessons learned

Energy Technology Data Exchange (ETDEWEB)

Crom, T.D.; Naugle, C.L. [Duke Engineering & Services, Inc., Charlotte, NC (United States); Turk, R.S. [ABB Combustion Engineering Nuclear Power, Windsor, CT (United States)

1995-03-01

Many lessons have been learned from the current generation of nuclear plants in the area of radiation protection. The following paper will outline how the lessons learned have been incorporated into the design and operational philosophy of the System 80+{trademark} Standard Design currently under development by ABB Combustion Engineering (ABB-CE) with support from Duke Engineering and Services, Inc. and Stone and Webster Engineering Corporation in the Balance-of-Plant design. The System 80+{trademark} Standard Design is a complete nuclear power plant for national and international markets, designed in direct response to utility needs for the 1990`s, and scheduled for Nuclear Regulatory Commission (NRC) Design Certification under the new standardization rule (10 CFR Part 52). System 80+{trademark} is a natural extension of System 80{sup R} technology, an evolutionary change based on proven Nuclear Steam Supply System (NSSS) in operation at Palo Verde in Arizona and under construction at Yonggwang in the Republic of Korea. The System 80+{trademark} Containment and much of the Balance of Plant design is based upon Duke Power Company`s Cherokee Plant, which was partially constructed in the late 1970`s, but, was later canceled (due to rapid declined in electrical load growth). The System 80+{trademark} Standard Design meets the requirements given in the Electric Power Research Institute (EPRI) Advanced Light Water Reactor (ALWR) Requirements Document. One of these requirements is to limit the occupational exposure to 100 person-rem/yr. This paper illustrates how this goal can be achieved through the incorporation of lessons learned, innovative design, and the implementation of a common sense approach to operation and maintenances practices.

Procedures and Standards for Residential Ventilation System Commissioning: An Annotated Bibliography

Energy Technology Data Exchange (ETDEWEB)

Stratton, J. Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2013-04-01

Beginning with the 2008 version of Title 24, new homes in California must comply with ANSI/ASHRAE Standard 62.2-2007 requirements for residential ventilation. Where installed, the limited data available indicate that mechanical ventilation systems do not always perform optimally or even as many codes and forecasts predict. Commissioning such systems when they are installed or during subsequent building retrofits is a step towards eliminating deficiencies and optimizing the tradeoff between energy use and acceptable IAQ. Work funded by the California Energy Commission about a decade ago at Berkeley Lab documented procedures for residential commissioning, but did not focus on ventilation systems. Since then, standards and approaches for commissioning ventilation systems have been an active area of work in Europe. This report describes our efforts to collect new literature on commissioning procedures and to identify information that can be used to support the future development of residential-ventilation-specific procedures and standards. We recommend that a standardized commissioning process and a commissioning guide for practitioners be developed, along with a combined energy and IAQ benefit assessment standard and tool, and a diagnostic guide for estimating continuous pollutant emission rates of concern in residences (including a database that lists emission test data for commercially-available labeled products).

The System 80+ Standard Plant Information Management System

Energy Technology Data Exchange (ETDEWEB)

Turk, R.S.; Bryan, R.E. [ABB Combuions Engineering Nuclear Systems (United States)

1998-07-01

Historically, electric nuclear power plant owners, following the completion of construction and startup, have been left with a mountain of hard-copy documents and drawings. Hundreds of thousands of hours are spent searching for relevant documents and, in most cases, the documents found require many other documents and drawings to fully understand the design basis. All too often the information is incomplete, and eventually becomes obsolete. In the U.S., utilities spend millions of dollars to discover design basis information and update as-built data for each plant. This information must then be stored in an easily accessed usable form to assist satisfy regulatory requirements and to improve plant operating efficiency. ABB Combustion Engineering Nuclear Systems (ABB-CE) has an active program to develop a state-of-the-art Plant Information Management System (IMS) for its advanced light water reactor, the System 80+TM Standard Plant Design. This program is supported by ABB's Product Data Management (PDM) and Computer Aided Engineering (CAE) efforts world wide. This paper describes the System 80+ plant IMS and how it will be used during the entire life cycle of the plant. (author)

The System 80+ Standard Plant Information Management System

International Nuclear Information System (INIS)

Turk, R.S.; Bryan, R.E.

1998-01-01

Historically, electric nuclear power plant owners, following the completion of construction and startup, have been left with a mountain of hard-copy documents and drawings. Hundreds of thousands of hours are spent searching for relevant documents and, in most cases, the documents found require many other documents and drawings to fully understand the design basis. All too often the information is incomplete, and eventually becomes obsolete. In the U.S., utilities spend millions of dollars to discover design basis information and update as-built data for each plant. This information must then be stored in an easily accessed usable form to assist satisfy regulatory requirements and to improve plant operating efficiency. ABB Combustion Engineering Nuclear Systems (ABB-CE) has an active program to develop a state-of-the-art Plant Information Management System (IMS) for its advanced light water reactor, the System 80+TM Standard Plant Design. This program is supported by ABB's Product Data Management (PDM) and Computer Aided Engineering (CAE) efforts world wide. This paper describes the System 80+ plant IMS and how it will be used during the entire life cycle of the plant. (author)

A constructive critique of the three standard systems

International Nuclear Information System (INIS)

Wilczek, F.

2004-01-01

It has become conventional to say that our knowledge of fundamental physical law is summarized in a Standard Model. But this convention lumps together two quite different conceptual structures, and leaves out another. I think it is more accurate and informative to say that our current, working description of fundamental physics is based on three standard conceptual systems. These systems are very different; so different that it is not inappropriate to call them the Good, the Bad, and the Ugly. They concern, respectively, the coupling of vector gauge particles, gravitons, and Higgs particles. It is quite a remarkable fact, in itself, that every nonlinear interaction we need to summarize our present knowledge of the basic (i.e., irreducible) laws of physics involves one or another of these particles. (author)

Secondary standard dosimetry system with automatic dose/rate calculation

International Nuclear Information System (INIS)

Duftschmid, K.E.; Bernhart, J.; Stehno, G.; Klosch, W.

1980-01-01

A versatile and automated secondary standard instrument has been designed for quick and accurate dose/rate measurement in a wide range of radiation intensity and quality (between 1 μR and 100 kR; 0.2 nC/kg - 20C/kg) for protection and therapy level dosimetry. The system is based on a series of secondary standard ionization chambers connected to a precision digital current integrator with microprocessor circuitry for data evaluation and control. Input of measurement parameters and calibration factors stored in an exchangeable memory chip provide computation of dose/rate values in the desired units. The ionization chambers provide excellent long-term stability and energy response and can be used with internal check sources to test validity of calibration. The system is a useful tool particularly for daily measurements in a secondary standard dosimetry laboratory or radiation therapy center. (H.K.)

25 CFR 276.7 - Standards for grantee financial management systems.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Standards for grantee financial management systems. 276.7... grantee financial management systems. (a) Grantee financial management systems for grants and subgrantee financial management systems for subgrants shall provide for: (1) Accurate, current, and complete disclosure...

Standard review plan for dry cask storage systems. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

The Standard Review Plan (SRP) For Dry Cask Storage Systems provides guidance to the Nuclear Regulatory Commission staff in the Spent Fuel Project Office for performing safety reviews of dry cask storage systems. The SRP is intended to ensure the quality and uniformity of the staff reviews, present a basis for the review scope, and clarification of the regulatory requirements. Part 72, Subpart B generally specifies the information needed in a license application for the independent storage of spent nuclear fuel and high level radioactive waste. Regulatory Guide 3.61 {open_quotes}Standard Format and Content for a Topical Safety Analysis Report for a Spent Fuel Dry Storage Cask{close_quotes} contains an outline of the specific information required by the staff. The SRP is divided into 14 sections which reflect the standard application format. Regulatory requirements, staff positions, industry codes and standards, acceptance criteria, and other information are discussed.

Standard review plan for dry cask storage systems. Final report

International Nuclear Information System (INIS)

1997-01-01

The Standard Review Plan (SRP) For Dry Cask Storage Systems provides guidance to the Nuclear Regulatory Commission staff in the Spent Fuel Project Office for performing safety reviews of dry cask storage systems. The SRP is intended to ensure the quality and uniformity of the staff reviews, present a basis for the review scope, and clarification of the regulatory requirements. Part 72, Subpart B generally specifies the information needed in a license application for the independent storage of spent nuclear fuel and high level radioactive waste. Regulatory Guide 3.61 open-quotes Standard Format and Content for a Topical Safety Analysis Report for a Spent Fuel Dry Storage Caskclose quotes contains an outline of the specific information required by the staff. The SRP is divided into 14 sections which reflect the standard application format. Regulatory requirements, staff positions, industry codes and standards, acceptance criteria, and other information are discussed

Japanese Cost Accounting Systems - analysis of the cost accounting systems of the Japanese cost accounting standard

OpenAIRE

Peter, Winter

2005-01-01

This paper aims at providing an insight into Japanese cost accounting. Firstly, the development of cost accounting in Japan is delineated. Subsequently, the cost accounting systems codified in the Japanese cost accounting standard are analysed based on the classification according to Hoitsch/Schmitz. Lastly, a critical appraisal of the cost accounting systems of the Japanese cost accounting standard as well as a comparison to German and American cost accounting systems are conducted.

On the structure of the quantum-mechanical probability models

International Nuclear Information System (INIS)

Cufaro-Petroni, N.

1992-01-01

In this paper the role of the mathematical probability models in the classical and quantum physics in shortly analyzed. In particular the formal structure of the quantum probability spaces (QPS) is contrasted with the usual Kolmogorovian models of probability by putting in evidence the connections between this structure and the fundamental principles of the quantum mechanics. The fact that there is no unique Kolmogorovian model reproducing a QPS is recognized as one of the main reasons of the paradoxical behaviors pointed out in the quantum theory from its early days. 8 refs

A trial fabrication of activity standard surface sources and positional standard surface sources for an imaging plate system

International Nuclear Information System (INIS)

Sato, Yasushi; Hino, Yoshio; Yamada, Takahiro; Matsumoto, Mikio

2003-01-01

An imaging plate system can detect low level activity, but quantitative analysis is difficult because there are no adequate standard surface sources. A new fabrication method was developed for standard surface sources by printing on a sheet of paper using an ink-jet printer with inks in which a radioactive material was mixed. The fabricated standard surface sources had high uniformity, high positional resolution arbitrary shapes and a broad intensity range. The standard sources were used for measurement of surface activity as an application. (H. Yokoo)

77 FR 7526 - Interpretation of Protection System Reliability Standard

Science.gov (United States)

2012-02-13

... Federal Power Act (FPA) requires a Commission-certified Electric Reliability Organization (ERO) to develop.... Cir. 2009). \\8\\ Mandatory Reliability Standards for the Bulk-Power System, Order No. 693, FERC Stats... a person that is ``directly and materially affected'' by Bulk-Power System reliability may request...

Developing standard transmission system for radiology reporting including key images

International Nuclear Information System (INIS)

Kim, Seon Chil

2007-01-01

Development of hospital information system and Picture Archiving Communication System is not new in the medical field, and the development of internet and information technology are also universal. In the course of such development, however, it is hard to share medical information without a refined standard format. Especially in the department of radiology, the role of PACS has become very important in interchanging information with other disparate hospital information systems. A specific system needs to be developed that radiological reports are archived into a database efficiently. This includes sharing of medical images. A model is suggested in this study in which an internal system is developed where radiologists store necessary images and transmit them is the standard international clinical format, Clinical Document Architecture, and share the information with hospitals. CDA document generator was made to generate a new file format and separate the existing storage system from the new system. This was to ensure the access to required data in XML documents. The model presented in this study added a process where crucial images in reading are inserted in the CDA radiological report generator. Therefore, this study suggests a storage and transmission model for CDA documents, which is different from the existing DICOM SR. Radiological reports could be better shared, when the application function for inserting images and the analysis of standard clinical terms are completed

Business School's Performance Management System Standards Design

Science.gov (United States)

Azis, Anton Mulyono; Simatupang, Togar M.; Wibisono, Dermawan; Basri, Mursyid Hasan

2014-01-01

This paper aims to compare various Performance Management Systems (PMS) for business school in order to find the strengths of each standard as inputs to design new model of PMS. There are many critical aspects and gaps notified for new model to improve performance and even recognized that self evaluation performance management is not well…

Development of standard ionization chamber counting system for activity measurements

International Nuclear Information System (INIS)

Pyun, Woong Beom; Lee, Hyun Koo; Lee, Hai Yong; Park, Tae Soon

1998-01-01

This study is to set up the activity measuring system using a 4π γ ionization chamber as used mainly in national standards laboratories that are responsible for radionuclide metrology. The software for automatic control between the electrometer and personal computer is developed using Microsoft visual basic 4.0 and IEEE488 Interface. The reproducibility of this 4π γ ionization chamber is about 0.02% and the background current is 0.054±0.024 pA. this 4π γ ionization chamber is calibrated by 6 standard gamma emitting radionuclides from KRISS. According to the result of this study, it is revealed that this 4π γ ionization chamber counting system can be used as a secondary standard instrument for radioactivity measurement

Development of standard ionization chamber counting system for activity measurements

CERN Document Server

Pyun, W B; Lee, H Y; Park, T S

1998-01-01

This study is to set up the activity measuring system using a 4 pi gamma ionization chamber as used mainly in national standards laboratories that are responsible for radionuclide metrology. The software for automatic control between the electrometer and personal computer is developed using Microsoft visual basic 4.0 and IEEE488 Interface. The reproducibility of this 4 pi gamma ionization chamber is about 0.02% and the background current is 0.054+-0.024 pA. this 4 pi gamma ionization chamber is calibrated by 6 standard gamma emitting radionuclides from KRISS. According to the result of this study, it is revealed that this 4 pi gamma ionization chamber counting system can be used as a secondary standard instrument for radioactivity measurement.

C-Band Airport Surface Communications System Standards Development, Phase I

Science.gov (United States)

Hall, Edward; Isaacs, James; Zelkin, Natalie; Henriksen. Steve

2010-01-01

This document is being provided as part of ITT's NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: "New ATM Requirements--Future Communications, C-Band and L-Band Communications Standard Development." The proposed future C-band (5091- to 5150-MHz) airport surface communication system, referred to as the Aeronautical Mobile Airport Communications System (AeroMACS), is anticipated to increase overall air-to-ground data communications systems capacity by using a new spectrum (i.e., not very high frequency (VHF)). Although some critical services could be supported, AeroMACS will also target noncritical services, such as weather advisory and aeronautical information services as part of an airborne System Wide Information Management (SWIM) program. AeroMACS is to be designed and implemented in a manner that will not disrupt other services operating in the C-band. This report defines the AeroMACS concepts of use, high-level system requirements, and architecture; the performance of supporting system analyses; the development of AeroMACS test and demonstration plans; and the establishment of an operational AeroMACS capability in support of C-band aeronautical data communications standards to be advanced in both international (International Civil Aviation Organization, ICAO) and national (RTCA) forums. This includes the development of system parameter profile recommendations for AeroMACS based on existing Institute of Electrical and Electronics Engineering (IEEE) 802.16e- 2009 standards

42 CFR 493.1299 - Standard: Postanalytic systems quality assessment.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Postanalytic systems quality assessment. 493.1299 Section 493.1299 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH....1291. (b) The postanalytic systems quality assessment must include a review of the effectiveness of...

42 CFR 493.1249 - Standard: Preanalytic systems quality assessment.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Preanalytic systems quality assessment. 493.1249 Section 493.1249 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH....1241 through 493.1242. (b) The preanalytic systems quality assessment must include a review of the...

40 CFR 31.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Standards for financial management... violation of the restrictions and prohibitions of applicable statutes. (b) The financial management systems... the financial management system of any applicant for financial assistance as part of a preaward review...

38 CFR 43.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... violation of the restrictions and prohibitions of applicable statutes. (b) The financial management systems... the financial management system of any applicant for financial assistance as part of a preaward review... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Standards for financial...

Tune and Orbit feedbacks performance: a user perspective

CERN Document Server

Ponce, L

2012-01-01

The presentation will present the performance and issues of tune and orbit feedbacks seen from the user (operation) perspective. Some statistics on the beam dumps causes will be presented to emphasize the two main limitations of the system : the issue on the tune measurement and the triggering of the QPS system of RQTs circuits. The possible improvements for 2012 will then be discussed together with the foreseen software changes for the orbit reference management.

42 CFR 493.1289 - Standard: Analytic systems quality assessment.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Analytic systems quality assessment. 493.1289 Section 493.1289 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND... through 493.1283. (b) The analytic systems quality assessment must include a review of the effectiveness...

45 CFR 92.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... with the financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 45 Public Welfare 1 2010-10-01 2010-10-01 false Standards for financial management systems. 92.20...

45 CFR 602.20 - Standards for financial management systems.

Science.gov (United States)

2010-10-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 45 Public Welfare 3 2010-10-01 2010-10-01 false Standards for financial management systems. 602.20...

14 CFR 1273.20 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Standards for financial management systems...

10 CFR 600.220 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 10 Energy 4 2010-01-01 2010-01-01 false Standards for financial management systems. 600.220...

Management plan documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 2

Science.gov (United States)

Callender, E. David; Steinbacher, Jody

1989-01-01

This is the second of five volumes of the Information System Life-Cycle and Documentation Standards. This volume provides a well-organized, easily used standard for management plans used in acquiring, assuring, and developing information systems and software, hardware, and operational procedures components, and related processes.

Interoperability through standardization: Electronic mail, and X Window systems

Science.gov (United States)

Amin, Ashok T.

1993-01-01

Since the introduction of computing machines, there has been continual advances in computer and communication technologies and approaching limits. The user interface has evolved from a row of switches, character based interface using teletype terminals and then video terminals, to present day graphical user interface. It is expected that next significant advances will come in the availability of services, such as electronic mail and directory services, as the standards for applications are developed and in the 'easy to use' interfaces, such as Graphical User Interface for example Window and X Window, which are being standardized. Various proprietary electronic mail (email) systems are in use within organizations at each center of NASA. Each system provides email services to users within an organization, however the support for email services across organizations and across centers exists at centers to a varying degree and is often easy to use. A recent NASA email initiative is intended 'to provide a simple way to send email across organizational boundaries without disruption of installed base.' The initiative calls for integration of existing organizational email systems through gateways connected by a message switch, supporting X.400 and SMTP protocols, to create a NASA wide email system and for implementation of NASA wide email directory services based on OSI standard X.500. A brief overview of MSFC efforts as a part of this initiative are described. Window based graphical user interfaces make computers easy to use. X window protocol has been developed at Massachusetts Institute of Technology in 1984/1985 to provide uniform window based interface in a distributed computing environment with heterogenous computers. It has since become a standard supported by a number of major manufacturers. Z Windows systems, terminals and workstations, and X Window applications are becoming available. However impact of its use in the Local Area Network environment on the network

Standards to support information systems integration in anatomic pathology.

Science.gov (United States)

Daniel, Christel; García Rojo, Marcial; Bourquard, Karima; Henin, Dominique; Schrader, Thomas; Della Mea, Vincenzo; Gilbertson, John; Beckwith, Bruce A

2009-11-01

Integrating anatomic pathology information- text and images-into electronic health care records is a key challenge for enhancing clinical information exchange between anatomic pathologists and clinicians. The aim of the Integrating the Healthcare Enterprise (IHE) international initiative is precisely to ensure interoperability of clinical information systems by using existing widespread industry standards such as Digital Imaging and Communication in Medicine (DICOM) and Health Level Seven (HL7). To define standard-based informatics transactions to integrate anatomic pathology information to the Healthcare Enterprise. We used the methodology of the IHE initiative. Working groups from IHE, HL7, and DICOM, with special interest in anatomic pathology, defined consensual technical solutions to provide end-users with improved access to consistent information across multiple information systems. The IHE anatomic pathology technical framework describes a first integration profile, "Anatomic Pathology Workflow," dedicated to the diagnostic process including basic image acquisition and reporting solutions. This integration profile relies on 10 transactions based on HL7 or DICOM standards. A common specimen model was defined to consistently identify and describe specimens in both HL7 and DICOM transactions. The IHE anatomic pathology working group has defined standard-based informatics transactions to support the basic diagnostic workflow in anatomic pathology laboratories. In further stages, the technical framework will be completed to manage whole-slide images and semantically rich structured reports in the diagnostic workflow and to integrate systems used for patient care and those used for research activities (such as tissue bank databases or tissue microarrayers).

Standards and the design of the advanced photon source control system

International Nuclear Information System (INIS)

McDowell, W.P.; Knott, M.J.; Lenkszus, F.R.

1992-01-01

The Advanced Photon Source (APS), now under construction at Argonne National Laboratory (ANL), is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. (J.P.N.)

Space and Missile Systems Center Standard: Systems Engineering Requirements and Products

Science.gov (United States)

2013-07-01

MISSILE SYSTEMS CENTER Air Force Space Command 483 N. Aviation Blvd. El Segundo, CA 90245 4. This standard has been approved for use on all Space...Any RF receiver with a burnout level of less than 30 dBm (1 mW). b. A summary of all significant areas are addressed in the EMC Control Plan...address 7. Date Submitted 8. Preparing Activity Space and Missile Systems Center AIR FORCE SPACE COMMAND 483 N. Aviation Blvd. El Segundo, CA 91245 Attention: SMC/EN February 2013

The proposed combustion standards and DOE thermal treatment systems

International Nuclear Information System (INIS)

McFee, J.; Hinman, M.B.; Eaton, D.; NcNeel, K.

1997-01-01

Under the provisions of the Clean Air Act (CAA) concerning emission of hazardous air pollutants (HAPs), the Environmental Protection Agency (EPA) published the proposed Revised Standards for Hazardous Waste Combustors on April 19, 1996 (EPA, 1996). These standards would apply to the existing Department of Energy (DOE) radioactive and mixed waste incinerators, and may be applied to several developing alternatives to incineration. The DOE has reviewed the basis for these regulations and prepared extensive comments to present concerns about the bases and implications of the standards. DOE is now discussing compliance options with the EPA for regulation of radioactive and mixed waste thermal treatment systems

Development of nuclear power standards and relevant system in China

International Nuclear Information System (INIS)

Cao Shudong

2008-01-01

By analyzing the history of nuclear power development and the status of nuclear power codes and standards in China, the significance and necessity to quicken the development of nuclear power standards system in China are pointed out, and the guiding ideology, development thoughts, working doctrine and development objectives are put forward in this paper. (authors)

Integrated management system - management standards evolution and the IAEA new approach

International Nuclear Information System (INIS)

Oliveira, Dirceu Paulo de; Zouain, Desiree Moraes

2007-01-01

The management standards application began in military and nuclear areas towards the end of Second World War, when some westerns countries developed quality standards to improve their means to assess suppliers' conditions to assure their products conformance, which was increasingly complex and required a higher degree of reliability. Afterwards, the quality standards application was extended to the consumer market focused on consumers' requirements satisfaction. Coming along the society crescent concern about quality of life, other management standards were developed, such as those dealing with environmental and sustainable development, occupational health and safety, social accountability and so on. As a consequence, the management process became complex. The management system integrated form approach makes possible the compatibility of distinct and complementary interests from several functions and disciplines involved and supply the absence of the organizations' holistic approach. According to this integrated management approach, the Agency - 'International Atomic Energy Agency' (IAEA) - decided to review the structure of the 50-C-Q standard - 'Quality Assurance for Safety in Nuclear Power Plants and Other Nuclear Installations', from 1996, publishing in 2006 the new GS-R-3 standard - 'The Management System for Facilities and Activities - Safety Requirements'. This work presents a brief evolution of management standards and integrated management approach, showing the Agency's new vision concerning this issue with the GS-R-3 standard publication. (author)

Rapid Prototyping of Standard Compliant Visible Light Communications System

OpenAIRE

Gavrincea, Ciprian; Baranda, Jorge; Henarejos, Pol

2014-01-01

This article describes the implementation of a prototype visible light communications system based on the IEEE 802.15.7 standard using low-cost commercial off-the-shelf analog devices. The aim of this article is to show that this standard provides a framework that could promote the introduction of applications into the market. Thus, these specifications could be further developed, reducing the gap between the industry and research communities. The implemented prototype makes use of software d...

Standard Guide for Specifying Thermal Performance of Geothermal Power Systems

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This guide covers power plant performance terms and criteria for use in evaluation and comparison of geothermal energy conversion and power generation systems. The special nature of these geothermal systems makes performance criteria commonly used to evaluate conventional fossil fuel-fired systems of limited value. This guide identifies the limitations of the less useful criteria and defines an equitable basis for measuring the quality of differing thermal cycles and plant equipment for geothermal resources. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

USL/DBMS NASA/PC R and D project system design standards

Science.gov (United States)

Dominick, Wayne D. (Editor); Moreau, Dennis R.

1984-01-01

A set of system design standards intended to assure the completeness and quality of designs developed for PC research and development projects is established. The standards presented address the areas of problem definition, initial design plan, design specification, and re-evaluation.

Open Architecture Standards and Information Systems (OASIS II ...

International Development Research Centre (IDRC) Digital Library (Canada)

Open Architecture Standards and Information Systems (OASIS II) - Developing Capacity, Sharing Knowledge and Good Principles Across eHealth in Africa. Health care across much of the African continent is hampered by meager resources and a growing burden of disease, with HIV/AIDS, tuberculosis (TB) and malaria ...

Medicaid management information systems performance standards: Health Care Financing Administration. Notice with comment period.

Science.gov (United States)

1981-06-30

This notice contains performance standards (review elements and factors). We are required by section 1903(r)(6)(E) of the Social Security Act to notify all States of proposed procedures, standards, and other requirements at least one quarter prior to the fiscal year in which the procedures, standards, and other requirements will be used for Medicaid Management Information Systems reapproval reviews. This Notice meets that statutory requirements. By October 1, 1981, we will use the performance standards and existing systems requirements when conducting the annual review of State system performance.

Development of the standard classification system of technical information in the field of RI-biomics and its application to the web system

International Nuclear Information System (INIS)

Jang, Sol Ah; Kim, Joo Yeon; Park, Tai Jin

2014-01-01

RI-Biomics is a new concept that combines radioisotopes (RI) and Biomics. For efficient collection of information, establishment of database for technical information system and its application to the system, there is an increasing need for constructing the standard classification system of technical information by its systematical classification. In this paper, we have summarized the development process of the standard classification system of technical information in the field of RI-Biomics and its application to the system. Constructing the draft version for the standard classification system of technical information was based on that standard classification one in national science and technology in Korea. The final classification system was then derived through the reconstruction and the feedback process based on the consultation from the 7 experts. These results were applied to the database of technical information system after transforming as standard code. Thus, the standard classification system were composed of 5 large classifications and 20 small classifications, and those classification are expected to establish the foundation of information system by achieving the circular structure of collection-analysis-application of information

Standards and the design of the Advanced Photon Source control system

International Nuclear Information System (INIS)

McDowell, W.P.; Knott, M.J.; Lenkszus, F.R.; Kraimer, M.R.; Daly, R.T.; Arnold, N.D.; Anderson, M.D.; Anderson, J.B.; Zieman, R.C.; Cha, Ben-Chin K.; Vong, F.C.; Nawrocki, G.J.; Gunderson, G.R.; Karonis, N.T.; Winans, J.R.

1991-01-01

The Advanced Photon Source (APS), now under construction at Argonne National Laboratory is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. In the conceptual stage the control system design group faced the challenges that face all control system designers: to force the machine designers to quantify and codify the system requirements, to protect the investment in hardware and software from rapid obsolescence, and to find methods of quickly incorporating new generations of equipment and replace of obsolete equipment without disrupting the exiting system. To solve these and related problems, the APS control system group made an early resolution to use standards in the design of the system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. The system will use high performance graphic workstations using an X-Windows Graphical User Interface at the operator interface level. It connects to VME-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

Trust Management in P2P systems using Standard TuLiP

NARCIS (Netherlands)

Czenko, M.R.; Doumen, J.M.; Etalle, Sandro

2008-01-01

In this paper we introduce Standard TuLiP - a new logic based Trust Management system. In Standard TuLiP, security decisions are based on security credentials, which can be issued by different entities and stored at different locations. Standard TuLiP directly supports the distributed credential

Trust management in P2P systems using standard TuLiP

NARCIS (Netherlands)

Czenko, M.; Doumen, J.M.; Etalle, S.; Karabulut, Y.; Mitchell, J.C.; Herrmann, P.; Jensen, C.D.

2008-01-01

In this paper we introduce Standard TuLiP - a new logic based Trust Management system. In Standard TuLiP, security decisions are based on security credentials, which can be issued by different entities and stored at different locations. Standard TuLiP directly supports the distributed credential

Trust Management in P2P Systems Using Standard TuLiP

NARCIS (Netherlands)

Czenko, M.R.; Doumen, J.M.; Etalle, Sandro

2008-01-01

In this paper we introduce Standard TuLiP - a new logic based Trust Management system. In Standard TuLiP, security decisions are based on security credentials, which can be issued by different entities and stored at different locations. Standard TuLiP directly supports the distributed credential

Improvement of standards on functional reliability of electric power systems

International Nuclear Information System (INIS)

Barinov, V.A.; Volkov, G.A.; Kalita, V.V.; Kogan, F.L.; Makarov, S.F.; Manevich, A.S.; Mogirev, V.V.; Sin'chugov, F.I.; Skopintsev, V.A.; Khvoshchinskaya, Z.G.

1993-01-01

Analysis of the most principal aspects of the existing standards and requirements on assuring safety and stability of electric power systems (EPS) and effective (reliable and economical) power supply of consumers is given. The reliability is determined as ability to accomplish the assigned functions. Basic recommendations on improving the standards regulating the safety and reliability of the NPP functioning are formulated

42 CFR 493.1252 - Standard: Test systems, equipment, instruments, reagents, materials, and supplies.

Science.gov (United States)

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Test systems, equipment, instruments... SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY... storage of reagents and specimens, accurate and reliable test system operation, and test result reporting...

Chinese green product standards: international experience and pathway for a unified system

Science.gov (United States)

Yun, Fu; Ling, Lin; Dongfeng, Gao; Shuo, Yang

2017-11-01

The establishment of a unified green product standard system is of great importance regarding the effective supply of green products and meeting trend of the consumption upgrade. It also is helpful to reduce the cost of green information disclosure of enterprises, and facilitate the supply-side structural reform. Based on the experience of developing and implementing green product standards in the EU, Germany, America, Japan and so on, combined with current Chinese standard systems including environmental protection, energy conservation, water conservation, low carbon, recycling, regeneration and organic, with the adoption of the life cycle thinking, this paper brings forward basic requirements on organizations including pollutant emissions, establishment of management system, energy conservation and emission reduction technology and green supply chain management, and proposes indicator requirements on product including resource attributes, energy attributes, environmental attributes and quality attributes, so as to guide the establishment of green product evaluation standards in the context of China.

77 FR 51649 - Federal Motor Vehicle Safety Standards; Motorcycle Brake Systems

Science.gov (United States)

2012-08-24

... motorcycle braking regulations from around the world, including the U.S. motorcycle brake systems standard.... Partial Failure Test--Split Service Brake System I. Power-Assisted Braking System Failure Test V. Other... motorcycle brake system technologies. In order to address modern braking technologies, the agency sought to...

CEN standards for solar thermal systems - State of the art and expectted impact

NARCIS (Netherlands)

Ree, B.G.C. van der; Pauschinger, Th.

1996-01-01

Since 1994, the European Committee for Standardization (CEN) Technical Committee TC 312 has been active in producing European Standards for thermal solar energy systems and components. In this paper, an overview of the present State of the Art of the draft standards is presented. These standards

System 80+{trademark} Standard Design: CESSAR design certification. Volume 8: Amendment I

Energy Technology Data Exchange (ETDEWEB)

1990-12-21

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 8 provides a description of instrumentation and controls.

A System Approach to Advanced Practice Clinician Standardization and High Reliability.

Science.gov (United States)

Okuno-Jones, Susan; Siehoff, Alice; Law, Jennifer; Juarez, Patricia

Advanced practice clinicians (APCs) are an integral part of the health care team. Opportunities exist within Advocate Health Care to standardize and optimize APC practice across the system. To enhance the role and talents of APCs, an approach to role definition and optimization of practice and a structured approach to orientation and evaluation are shared. Although in the early stages of development, definition and standardization of accountabilities in a framework to support system changes are transforming the practice of APCs.

76 FR 62 - Interpretive Standards for Systemic Compensation Discrimination and Voluntary Guidelines for Self...

Science.gov (United States)

2011-01-03

... 1250-ZA00 Interpretive Standards for Systemic Compensation Discrimination and Voluntary Guidelines for... Order 11246 with respect to Systemic Compensation Discrimination (Standards) and Voluntary Guidelines... Compensation Discrimination [[Page 63

[Design and implementation of medical instrument standard information retrieval system based on APS.NET].

Science.gov (United States)

Yu, Kaijun

2010-07-01

This paper Analys the design goals of Medical Instrumentation standard information retrieval system. Based on the B /S structure,we established a medical instrumentation standard retrieval system with ASP.NET C # programming language, IIS f Web server, SQL Server 2000 database, in the. NET environment. The paper also Introduces the system structure, retrieval system modules, system development environment and detailed design of the system.

Information Systems Security Management: A Review and a Classification of the ISO Standards

Science.gov (United States)

Tsohou, Aggeliki; Kokolakis, Spyros; Lambrinoudakis, Costas; Gritzalis, Stefanos

The need for common understanding and agreement of functional and non-functional requirements is well known and understood by information system designers. This is necessary for both: designing the "correct" system and achieving interoperability with other systems. Security is maybe the best example of this need. If the understanding of the security requirements is not the same for all involved parties and the security mechanisms that will be implemented do not comply with some globally accepted rules and practices, then the system that will be designed will not necessarily achieve the desired security level and it will be very difficult to securely interoperate with other systems. It is therefore clear that the role and contribution of international standards to the design and implementation of security mechanisms is dominant. In this paper we provide a state of the art review on information security management standards published by the International Organization for Standardization and the International Electrotechnical Commission. Such an analysis is meaningful to security practitioners for an efficient management of information security. Moreover, the classification of the standards in the clauses of ISO/IEC 27001:2005 that results from our analysis is expected to provide assistance in dealing with the plethora of security standards.

Recommendations for a proposed standard for performing systems analysis

International Nuclear Information System (INIS)

LaChance, J.; Whitehead, D.; Drouin, M.

1998-01-01

In August 1995, the Nuclear Regulatory Commission (NRC) issued a policy statement proposing improved regulatory decisionmaking by increasing the use of PRA [probabilistic risk assessment] in all regulatory matters to the extent supported by the state-of-the-art in PRA methods and data. A key aspect in using PRA in risk-informed regulatory activities is establishing the appropriate scope and attributes of the PRA. In this regard, ASME decided to develop a consensus PRA Standard. The objective is to develop a PRA Standard such that the technical quality of nuclear plant PRAs will be sufficient to support risk-informed regulatory applications. This paper presents examples recommendations for the systems analysis element of a PRA for incorporation into the ASME PRA Standard

Meeting Residential Ventilation Standards Through Dynamic Control of Ventilation Systems

OpenAIRE

Sherman, Max H.

2011-01-01

Existing ventilation standards, including American Society of Heating, Refrigerating, and Air-conditioning Engineers (ASHRAE) Standard 62.2, specify continuous operation of a defined mechanical ventilation system to provide minimum ventilation, with time-based intermittent operation as an option. This requirement ignores several factors and concerns including: other equipment such as household exhaust fans that might incidentally provide ventilation, negative impacts of ventilation when outd...

Flexibility First, Then Standardize: A Strategy for Growing Inter-Departmental Systems.

Science.gov (United States)

á Torkilsheyggi, Arnvør

2015-01-01

Any attempt to use IT to standardize work practices faces the challenge of finding a balance between standardization and flexibility. In implementing electronic whiteboards with the goal of standardizing inter-departmental practices, a hospital in Denmark chose to follow the strategy of "flexibility first, then standardization." To improve the local grounding of the system, they first focused on flexibility by configuring the whiteboards to support intra-departmental practices. Subsequently, they focused on standardization by using the white-boards to negotiate standardization of inter-departmental practices. This paper investigates the chosen strategy and finds: that super users on many wards managed to configure the whiteboard to support intra-departmental practices; that initiatives to standardize inter-departmental practices improved coordination of certain processes; and that the chosen strategy posed a challenge for finding the right time and manner to shift the balance from flexibility to standardization.

41 CFR 105-71.120 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Standards for financial... violation of the restrictions and prohibitions of applicable statutes. (b) The financial management systems... the financial management system of any applicant for financial assistance as part of a preaward review...

System 80+{trademark} Standard Design: CESSAR design certification. Volume 11: Amendment I

Energy Technology Data Exchange (ETDEWEB)

1990-12-21

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 11 discusses Radiation Protection, Conduct of Operations, and the Initial Test Program.

Gathering positive experience

CERN Document Server

2009-01-01

Last Monday, the new CERN Machine Advisory Committee (CMAC) met for the first time, and we had good news to tell its members. Over the weekend, injection tests for both LHC beams were successfully carried out. In other words, we’ve had beam in the LHC for the first time since September 2008. That’s a good feeling, but it’s no reason for complacency. There’s still a long way to go before first physics at the new energy frontier. As the Bulletin has reported over recent weeks, we’re gathering a lot of positive experience with the new quench detection and protection system (QPS), which is already allowing us to monitor the LHC far better than we were able to in the past. So far, the QPS for three of the LHC’s eight sectors has been put through its paces, and we’ve also power tested those sectors to 2000 amperes, the equivalent of around 1.2 TeV per beam. The next step is to slowly increase the current to 4000 amperes, and...

The latest from the LHC

CERN Document Server

2009-01-01

On 26 August, the first two fully tested crates for the new quench protection system (QPS) were installed in Sector 1-2. These are the first of 436 crates that will be installed around the ring. The two crates include detectors for both the enhanced busbar protection and the symmetric quench protection (more details). To test the crates before installation, a dedicated test bed has been created, capable of simulating all the conditions in the LHC, from a symmetric quench to an increase in busbar resistance. The teams are working two shifts a day, including weekends, to test the new crates. Two more test benches are also being built to increase the production rate. The whole task is on target for completion in mid October. Another important new task for the QPS team is to try and speed up the energy extraction from the magnets. The quicker the energy can be extracted the lower the risk of dangerously high temperatures should a quench occur. The time constant for the dipoles...

Buying Program of the Standard Automated Materiel Management System. Automated Small Purchase System: Defense Supply Center Philadelphia

National Research Council Canada - National Science Library

2001-01-01

The Standard Automated Materiel Management System Automated Small Purchase System is a fully automated micro-purchases system used by the General and Industrial Directorate at the Defense Supply Center Philadelphia...

47 CFR 76.905 - Standards for identification of cable systems subject to effective competition.

Science.gov (United States)

2010-10-01

... system. (2) The franchise area is: (i) Served by at least two unaffiliated multichannel video programming... 47 Telecommunication 4 2010-10-01 2010-10-01 false Standards for identification of cable systems... Regulation § 76.905 Standards for identification of cable systems subject to effective competition. (a) Only...

The new international standard ISO 14001: 2004 environmental management system

International Nuclear Information System (INIS)

Oheba, Jamal Basher

2006-01-01

ISO 14001 is one standard in the ISO 14000 series of standards developed by International Organization of Standardization (ISO). Since it was published in 19096, it has rapidly become the most important environmental standard in the world. ISO 14001 is an environmental management system (EMS) that can be classified into environmental technologies provides a systematic procedure to all kind of organizations to prevent pollutions, protect environment and to improve their overall environmental performance. This new standard ISO 14001 2004 was published on November 15, 2004. It cancels and replaced the old ISO 14001-1996. Because the important of the previous standard for our local industries, firms, ...etc, this paper presents ISO 14001 concepts, issues, benefits and focuses on the stages of implementation to achieve ISO 14001-2004 certification which includes general requirements environmental policy, planning (objectives, targets ..), implementation and operations, checking and management review ...etc and presents how to apply isotop time saver software to design records, and to save time to implement ISO 14001 2004 and finally a conclusion is provided.(Author)

Standardization of education as essential to the development of regional educational systems

Directory of Open Access Journals (Sweden)

Shevchuk Andrey

2013-01-01

Full Text Available The problematic aspects of the current educational standards in Ukraine as important legal instruments of regional educational systems were viewed. The regulated areas of education standards in Ukraine and the traditional approach based on the identified areas of their innovative changes where described. The main directions of innovation education standards depending on their subject focus where systemised.

14 CFR 25.1445 - Equipment standards for the oxygen distributing system.

Science.gov (United States)

2010-01-01

... distributing system. 25.1445 Section 25.1445 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT... Miscellaneous Equipment § 25.1445 Equipment standards for the oxygen distributing system. (a) When oxygen is supplied to both crew and passengers, the distribution system must be designed for either— (1) A source of...

GoldenBraid: An Iterative Cloning System for Standardized Assembly of Reusable Genetic Modules

Science.gov (United States)

Sarrion-Perdigones, Alejandro; Falconi, Erica Elvira; Zandalinas, Sara I.; Juárez, Paloma; Fernández-del-Carmen, Asun; Granell, Antonio; Orzaez, Diego

2011-01-01

Synthetic Biology requires efficient and versatile DNA assembly systems to facilitate the building of new genetic modules/pathways from basic DNA parts in a standardized way. Here we present GoldenBraid (GB), a standardized assembly system based on type IIS restriction enzymes that allows the indefinite growth of reusable gene modules made of standardized DNA pieces. The GB system consists of a set of four destination plasmids (pDGBs) designed to incorporate multipartite assemblies made of standard DNA parts and to combine them binarily to build increasingly complex multigene constructs. The relative position of type IIS restriction sites inside pDGB vectors introduces a double loop (“braid”) topology in the cloning strategy that allows the indefinite growth of composite parts through the succession of iterative assembling steps, while the overall simplicity of the system is maintained. We propose the use of GoldenBraid as an assembly standard for Plant Synthetic Biology. For this purpose we have GB-adapted a set of binary plasmids for A. tumefaciens-mediated plant transformation. Fast GB-engineering of several multigene T-DNAs, including two alternative modules made of five reusable devices each, and comprising a total of 19 basic parts are also described. PMID:21750718

System for digitalization of medical images based on DICOM standard

Directory of Open Access Journals (Sweden)

Čabarkapa Slobodan

2009-01-01

Full Text Available According to DICOM standard, which defines both medical image information and user information, a new system for digitalizing medical images is involved as a part of the main system for archiving and retrieving medical databases. The basic characteristics of this system are described in this paper. Furthermore, the analysis of some important DICOM header's tags which are used in this system, are presented, too. Having chosen the appropriate tags in order to preserve important information, the efficient system has been created. .

76 FR 64082 - Mandatory Reliability Standards for the Bulk-Power System; Notice of Staff Meeting

Science.gov (United States)

2011-10-17

... Reliability Standards for the Bulk-Power System; Notice of Staff Meeting Take notice that the Federal Energy... R1.3.10 of Commission-approved transmission planning Reliability Standard TPL-002- 0 (System... additional actions necessary to address the matter.\\3\\ \\1\\ Mandatory Reliability Standards for the Bulk-Power...

The Weighted Airman Promotion System: Standardizing Test Scores

Science.gov (United States)

2008-01-01

u th o ri ze d Top 3/E6 ratio, inventory 1401206040 100 70 130 5R 2F 2G 3N 2M 2A 4J 4C 4P 4T 4B 1W 2T 3P 1T 4A 2S 5J 1A 1S1C 6F 4N 7S 4R 4E 1N 3A 3V...System: Standardizing Test Scores AFHRL convened a panel to identify the relevant factors to consider, and then sit as a promotion board and rank...Costs If the Air Force decided to standardize test scores, there would be three basic types of costs: implementation costs, marketing costs, and

A systems approach to accepted standards of care: Shifting the blame

Directory of Open Access Journals (Sweden)

David G. Glance

2011-09-01

Full Text Available In healthcare, from a legal perspective, the standard ofacceptable practice has been generally set by the courts anddefined as healthcare professionals acting in a manner thatis widely accepted by their peers as meeting an acceptablestandard of care. This view, however, reflects the state ofhow practice “is” rather than what it “ought to be”. What isought to be depends on whether you take a “person” or“system” oriented approach to practice.The increasing pressures of lack of money and resources,and an ever-increasing need for care are bringing pressureon the health services to move to a system approach andthis is gaining acceptance both with clinicians and thuseventually the courts.A systems-type approach to healthcare will, by necessity,embrace clinical protocols and guidelines supported byclinical information systems. It will also see blame for errorsshifting from clinicians to the organisations that employthem.This paper argues that a continued use of a person-basedapproach to healthcare, developed through an historicalrecord of practice by individual clinicians, is no longeradequate defence in a case of supposed negligence.When the healthcare system has codified clinical guidelinesand digital data gathered across thousands of clinicians andtheir patients, it is possible to compute adequate levels ofcare and expect clinicians and the healthcare system ingeneral to meet these minimum standards.Future negligence decisions will rely on a systems-basedbest practice standard of care determined through evidencerather than opinion

Piping benchmark problems for the ABB/CE System 80+ Standardized Plant

International Nuclear Information System (INIS)

Bezler, P.; DeGrassi, G.; Braverman, J.; Wang, Y.K.

1994-07-01

To satisfy the need for verification of the computer programs and modeling techniques that will be used to perform the final piping analyses for the ABB/Combustion Engineering System 80+ Standardized Plant, three benchmark problems were developed. The problems are representative piping systems subjected to representative dynamic loads with solutions developed using the methods being proposed for analysis for the System 80+ standard design. It will be required that the combined license licensees demonstrate that their solution to these problems are in agreement with the benchmark problem set. The first System 80+ piping benchmark is a uniform support motion response spectrum solution for one section of the feedwater piping subjected to safe shutdown seismic loads. The second System 80+ piping benchmark is a time history solution for the feedwater piping subjected to the transient loading induced by a water hammer. The third System 80+ piping benchmark is a time history solution of the pressurizer surge line subjected to the accelerations induced by a main steam line pipe break. The System 80+ reactor is an advanced PWR type

The strategic use of standardized information exchange technology in a university health system.

Science.gov (United States)

Cheng, Po-Hsun; Chen, Heng-Shuen; Lai, Feipei; Lai, Jin-Shin

2010-04-01

This article illustrates a Web-based health information system that is comprised of specific information exchange standards related to health information for healthcare services in National Taiwan University Health System. Through multidisciplinary teamwork, medical and informatics experts collaborated and studied on system scope definition, standard selection challenges, system implementation barriers, system management outcomes, and further expandability of other systems. After user requirement analysis and prototyping, from 2005 to 2008, an online clinical decision support system with multiple functions of reminding and information push was implemented. It was to replace its original legacy systems and serve among the main hospital and three branches of 180-200 clinics and 7,500-8,000 patient visits per day. To evaluate the effectiveness of this system, user surveys were performed, which revealed that the average score of user satisfaction increased from 2.80 to 3.18 on a 4-point scale. Among the items, especially e-learning for training service, courtesy communications for system requests, and courtesy communications for system operations showed statistically significant improvement. From this study, the authors concluded that standardized information exchange technologies can be used to create a brand new enterprise value and steadily obtain more competitive advantages for a prestige healthcare system.

Comparison of pituitary and recombinant human thyrotropin standards in an immunoradiometric system

International Nuclear Information System (INIS)

Blanca Fernandez, Silvia; Rodriguez Gonzalez, Julio Cesar; Nisembaum Alas, Amaparo; Sevy Gonzalez, O.

1998-01-01

Results of two standards of human thyrotropin of pituitaries (B) and recombinant (C) origen supplied by the Instituto of pesquisas Energeticas y Nucleares, Brazil, were compared in our immunoradiometric reference system that use an human thyrotropin pituitary standard of local production (A). This work was supported by the International Atomic Energy Agency for an inter-regional comparison and set up of a reference standard

Executive overview and introduction to the SMAP information system life-cycle and documentation standards

Science.gov (United States)

1989-01-01

An overview of the five volume set of Information System Life-Cycle and Documentation Standards is provided with information on its use. The overview covers description, objectives, key definitions, structure and application of the standards, and document structure decisions. These standards were created to provide consistent NASA-wide structures for coordinating, controlling, and documenting the engineering of an information system (hardware, software, and operational procedures components) phase by phase.

BVR Standardization of the CCD Photometric System of Chungbuk National University Observatory

Directory of Open Access Journals (Sweden)

Jang-Hae Jeong

2009-06-01

Full Text Available BVR observations for 52 standard stars were performed using the 1-m reflecter with 2K CCD System of Chungbuk National University Observatory(CBNUO in 2008. We obtained 1,322 CCD images to establish a correlation between our bvr system and the standard Johnson-Cousins BVR system. We derived the tentative equations of transformation between then as follows; V = v-0.0303(B-V+0.0466 B-V = 1.3475(b-v-0.0251 V-R = 1.0641(v-r-0.0125 Using these equations the magnitudes in V, B-V, and V-R for 197 stars were obtained.

Electronic Information Standards to Support Obesity Prevention and Bridge Services Across Systems, 2010-2015.

Science.gov (United States)

Wiltz, Jennifer L; Blanck, Heidi M; Lee, Brian; Kocot, S Lawrence; Seeff, Laura; McGuire, Lisa C; Collins, Janet

2017-10-26

Electronic information technology standards facilitate high-quality, uniform collection of data for improved delivery and measurement of health care services. Electronic information standards also aid information exchange between secure systems that link health care and public health for better coordination of patient care and better-informed population health improvement activities. We developed international data standards for healthy weight that provide common definitions for electronic information technology. The standards capture healthy weight data on the "ABCDs" of a visit to a health care provider that addresses initial obesity prevention and care: assessment, behaviors, continuity, identify resources, and set goals. The process of creating healthy weight standards consisted of identifying needs and priorities, developing and harmonizing standards, testing the exchange of data messages, and demonstrating use-cases. Healthy weight products include 2 message standards, 5 use-cases, 31 LOINC (Logical Observation Identifiers Names and Codes) question codes, 7 healthy weight value sets, 15 public-private engagements with health information technology implementers, and 2 technical guides. A logic model and action steps outline activities toward better data capture, interoperable systems, and information use. Sharing experiences and leveraging this work in the context of broader priorities can inform the development of electronic information standards for similar core conditions and guide strategic activities in electronic systems.

Concept for an International Standard related to Space Weather Effects on Space Systems

Science.gov (United States)

Tobiska, W. Kent; Tomky, Alyssa

There is great interest in developing an international standard related to space weather in order to specify the tools and parameters needed for space systems operations. In particular, a standard is important for satellite operators who may not be familiar with space weather. In addition, there are others who participate in space systems operations that would also benefit from such a document. For example, the developers of software systems that provide LEO satellite orbit determination, radio communication availability for scintillation events (GEO-to-ground L and UHF bands), GPS uncertainties, and the radiation environment from ground-to-space for commercial space tourism. These groups require recent historical data, current epoch specification, and forecast of space weather events into their automated or manual systems. Other examples are national government agencies that rely on space weather data provided by their organizations such as those represented in the International Space Environment Service (ISES) group of 14 national agencies. Designers, manufacturers, and launchers of space systems require real-time, operational space weather parameters that can be measured, monitored, or built into automated systems. Thus, a broad scope for the document will provide a useful international standard product to a variety of engineering and science domains. The structure of the document should contain a well-defined scope, consensus space weather terms and definitions, and internationally accepted descriptions of the main elements of space weather, its sources, and its effects upon space systems. Appendices will be useful for describing expanded material such as guidelines on how to use the standard, how to obtain specific space weather parameters, and short but detailed descriptions such as when best to use some parameters and not others; appendices provide a path for easily updating the standard since the domain of space weather is rapidly changing with new advances

A Microfluidic Immunostaining System Enables Quality Assured and Standardized Immunohistochemical Biomarker Analysis

Science.gov (United States)

Kwon, Seyong; Cho, Chang Hyun; Kwon, Youngmee; Lee, Eun Sook; Park, Je-Kyun

2017-04-01

Immunohistochemistry (IHC) plays an important role in biomarker-driven cancer therapy. Although there has been a high demand for standardized and quality assured IHC, it has rarely been achieved due to the complexity of IHC testing and the subjective validation-based process flow of IHC quality control. We present here a microfluidic immunostaining system for the standardization of IHC by creating a microfluidic linearly graded antibody (Ab)-staining device and a reference cell microarray. Unlike conventional efforts, our system deals primarily with the screening of biomarker staining conditions for quantitative quality assurance testing in IHC. We characterized the microfluidic matching of Ab staining intensity using three HER2 Abs produced by different manufacturers. The quality of HER2 Ab was also validated using tissues of breast cancer patients, demonstrating that our system is an efficient and powerful tool for the standardization and quality assurance of IHC.

Trust Management in P2P systems using Standard TuLiP

OpenAIRE

Czenko, M.R.; Doumen, J.M.; Etalle, Sandro

2008-01-01

In this paper we introduce Standard TuLiP - a new logic based Trust Management system. In Standard TuLiP, security decisions are based on security credentials, which can be issued by different entities and stored at different locations. Standard TuLiP directly supports the distributed credential storage by providing a sound and complete Lookup and Inference AlgoRithm (LIAR). In this paper we focus on (a) the language of Standard TuLiP and (b) on the practical considerations which arise when d...

[Discussion on research thinking of traditional Chinese medicine standardization system based on whole process quality control].

Science.gov (United States)

Dong, Ling; Sun, Yu; Pei, Wen-Xuan; Dai, Jun-Dong; Wang, Zi-Yu; Pan, Meng; Chen, Jiang-Peng; Wang, Yun

2017-12-01

The concept of "Quality by design" indicates that good design for the whole life cycle of pharmaceutical production enables the drug to meet the expected quality requirements. Aiming at the existing problems of the traditional Chinese medicine (TCM) industry, the TCM standardization system was put forward in this paper from the national strategic level, under the guidance by the idea of quality control in international manufacturing industry and with considerations of TCM industry's own characteristics and development status. The connotation of this strategy was to establish five interrelated systems: multi-indicators system based on tri-indicators system, quality standard and specification system of TCM herbal materials and decoction pieces, quality traceability system, data monitoring system based on whole-process quality control, and whole-process quality management system of TCM, and achieve the whole process systematic and scientific study in TCM industry through "top-level design-implement in steps-system integration" workflow. This article analyzed the correlation between the quality standards of all links, established standard operating procedures of each link and whole process, and constructed a high standard overall quality management system for TCM industry chains, in order to provide a demonstration for the establishment of TCM whole-process quality control system and provide systematic reference and basis for standardization strategy in TCM industry. Copyright© by the Chinese Pharmaceutical Association.

28 CFR 66.20 - Standards for financial management systems.

Science.gov (United States)

2010-07-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Standards for financial management...

Building a computer-aided design capability using a standard time share operating system

Science.gov (United States)

Sobieszczanski, J.

1975-01-01

The paper describes how an integrated system of engineering computer programs can be built using a standard commercially available operating system. The discussion opens with an outline of the auxiliary functions that an operating system can perform for a team of engineers involved in a large and complex task. An example of a specific integrated system is provided to explain how the standard operating system features can be used to organize the programs into a simple and inexpensive but effective system. Applications to an aircraft structural design study are discussed to illustrate the use of an integrated system as a flexible and efficient engineering tool. The discussion concludes with an engineer's assessment of an operating system's capabilities and desirable improvements.

STANDARDIZATION AND APPLICATION OF PLASTIC CARDS IN THE EDUCATIONAL SYSTEMS

Directory of Open Access Journals (Sweden)

Polina V. Baranova

2015-01-01

Full Text Available The application of plastic cards has been widely increasing in various fields of life, business and education. They have already become up-to-date and convenient attribute of our daily life. There are emerging more and more areas where they can be used in a convenient and practical way. Contactless smart cards can be used in access control in the educational systems. This article gives an overview of existing standards dealing with contactless identification smart-cards. All standards covered in this article are developed by the Federal State Unitary Enterprise VNIINMASH jointly with TC 22 «Information Technology» based on their own authentic Russian translation of international standards. 

Standard practice for verification and classification of extensometer systems

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This practice covers procedures for the verification and classification of extensometer systems, but it is not intended to be a complete purchase specification. The practice is applicable only to instruments that indicate or record values that are proportional to changes in length corresponding to either tensile or compressive strain. Extensometer systems are classified on the basis of the magnitude of their errors. 1.2 Because strain is a dimensionless quantity, this document can be used for extensometers based on either SI or US customary units of displacement. Note 1—Bonded resistance strain gauges directly bonded to a specimen cannot be calibrated or verified with the apparatus described in this practice for the verification of extensometers having definite gauge points. (See procedures as described in Test Methods E251.) 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish app...

An accurate on-site calibration system for electronic voltage transformers using a standard capacitor

Science.gov (United States)

Hu, Chen; Chen, Mian-zhou; Li, Hong-bin; Zhang, Zhu; Jiao, Yang; Shao, Haiming

2018-05-01

Ordinarily electronic voltage transformers (EVTs) are calibrated off-line and the calibration procedure requires complex switching operations, which will influence the reliability of the power grid and induce large economic losses. To overcome this problem, this paper investigates a 110 kV on-site calibration system for EVTs, including a standard channel, a calibrated channel and a PC equipped with the LabView environment. The standard channel employs a standard capacitor and an analogue integrating circuit to reconstruct the primary voltage signal. Moreover, an adaptive full-phase discrete Fourier transform (DFT) algorithm is proposed to extract electrical parameters. The algorithm involves the process of extracting the frequency of the grid, adjusting the operation points, and calculating the results using DFT. In addition, an insulated automatic lifting device is designed to realize the live connection of the standard capacitor, which is driven by a wireless remote controller. A performance test of the capacitor verifies the accurateness of the standard capacitor. A system calibration test shows that the system ratio error is less than 0.04% and the phase error is below 2‧, which meets the requirement of the 0.2 accuracy class. Finally, the developed calibration system was used in a substation, and the field test data validates the availability of the system.

System 80+trademark Standard Design: CESSAR design certification. Volume 16

International Nuclear Information System (INIS)

1997-01-01

This report has been prepared in support of the industry effort to standardize nuclear plant designs. This document describes the Combustion Engineering, Inc. System 80+trademark Standard Design. This volume contain Chapter 18 -- Human Factors Engineering. Topics covered include: design team organization and responsibilities; design goals and design bases; design process and application to human factors engineering; functional task analysis; control room configuration; information presentation and panel layout evaluation; control and monitoring outside the main control room; and verification and validation

15 CFR 24.20 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Standards for financial management...

13 CFR 143.20 - Standards for financial management systems.

Science.gov (United States)

2010-01-01

... financial reporting requirements of the grant or subgrant. (2) Accounting records. Grantees and subgrantees... advances to the grantees. (c) An awarding agency may review the adequacy of the financial management system... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Standards for financial management...

Japanese national project for establishment of codes and standards for stationary PEFC system

International Nuclear Information System (INIS)

Sumi, S.; Ohmura, T.; Yamaguchi, R.; Kikuzawa, H.

2003-01-01

For the purpose of practical utilization of the PEFC cogeneration system, we are promoting the national projects of the 'Establishment of Codes and Standards for Stationary PEFC System'. The objective is to prepare the software platforms for wide spreading use, which are required in the introduction stage of the PEFC cogeneration systems, such as code and standards for safety, reliability, performance and so on. For this objective, using test samples of the systems and the stacks, developments of test and evaluation devices, collection of various kinds of data and establishment of test and evaluation methods are under way. (author)

Leadership Strategies in Implementation of High-School Standards-Based Grading Systems

Science.gov (United States)

Pritzl, Jerome

2016-01-01

This multi-site case study examined leadership strategies used during successful implementation of standards-based grading systems in three Wisconsin high schools. It found that leaders' reported commitment, patience, and persistence showed evidence of sustainable, high-functioning systems. It drew two main conclusions: first, school leaders need…

Management control and status reports documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 5

Science.gov (United States)

Callender, E. David; Steinbacher, Jody

1989-01-01

This is the fifth of five volumes on Information System Life-Cycle and Documentation Standards. This volume provides a well organized, easily used standard for management control and status reports used in monitoring and controlling the management, development, and assurance of informations systems and software, hardware, and operational procedures components, and related processes.

Standardized facility record and report model system (FARMS) for material accounting and control

International Nuclear Information System (INIS)

Nishimura, Hideo; Ihara, Hitoshi; Hisamatsu, Yoshinori.

1990-07-01

A facility in which nuclear materials are handled maintains a facility system of accounting for and control of nuclear material. Such a system contains, as one of key elements, a record and report system. This record and report information system is a rather complex one because it needs to conform to various requirements from the national or international safeguards authorities and from the plant operator who has to achieve a safe and economical operation of the plant. Therefore it is mandatory to computerize such information system. The authors have reviewed these requirements and standardized the book-keeping and reporting procedures in line with their computerization. On the basis of this result the authors have developed a computer system, FARMS, named as an acronym of standardized facility record and report model system, mainly reflecting the requirements from the national and international safeguards authorities. The development of FARMS has also been carried out as a JASPAS - Japan Support Programme for Agency Safeguards - project since 1985 and the FARMS code was demonstrated as an accountancy tool in the regional SSAC training courses held in Japan in 1985 and 1987. This report describes the standardization of a record and report system at the facility level, its computerization as a model system and the demonstration of the developed system, FARMS. (author)

Lean environmental management integration system for sustainability of ISO 14001:2004 standard implementation

Directory of Open Access Journals (Sweden)

Perumal Puvanasvaran

2014-10-01

Full Text Available Purpose: The purpose of this study is to present a model for integrating Lean Principles with ISO 14001 Environmental Management System.Design/methodology/approach: To achieve the objective of the study, the methodology used in this study is based on preliminary literature review of ISO 14001 standards and Lean Principles as well as certain case reports from various proponents and authors of ISO 14001 and Lean as noted in various articles and journals and some books.Findings and Originality/value: The findings of this study are a new model called Lean Environmental Management Integration System (LEMIS has been developed and leads to the creation of these measurement standards for evaluating the organization, making its environmental efforts more realistic, focused and attainable.Research limitations/implications: Future research should be conducted case studies in this direction are required to be conducted for examining the feasibility of amalgamation and implementing ISO 14001:2004 standards with the philosophy of Lean Principles to enable the achievement of world class standards.Practical implications: This model helps to eliminate any wasteful processes in the organization’s implementation of the ISO 14001 standard thus leading to higher environmental performance.  Integrating the standard with Lean principles through LEMIS model helps to specify these performance measures making the standard achieve sustainability and continual improvement.Originality/value: This study presents a unique approach of integrating the two main models, namely Lean Principles and ISO 14001 Environmental Management System, as a single framework benefiting contemporary organizations.

Design and implementation of the standards-based personal intelligent self-management system (PICS).

Science.gov (United States)

von Bargen, Tobias; Gietzelt, Matthias; Britten, Matthias; Song, Bianying; Wolf, Klaus-Hendrik; Kohlmann, Martin; Marschollek, Michael; Haux, Reinhold

2013-01-01

Against the background of demographic change and a diminishing care workforce there is a growing need for personalized decision support. The aim of this paper is to describe the design and implementation of the standards-based personal intelligent care systems (PICS). PICS makes consistent use of internationally accepted standards such as the Health Level 7 (HL7) Arden syntax for the representation of the decision logic, HL7 Clinical Document Architecture for information representation and is based on a open-source service-oriented architecture framework and a business process management system. Its functionality is exemplified for the application scenario of a patient suffering from congestive heart failure. Several vital signs sensors provide data for the decision support system, and a number of flexible communication channels are available for interaction with patient or caregiver. PICS is a standards-based, open and flexible system enabling personalized decision support. Further development will include the implementation of components on small computers and sensor nodes.

Study on the standardization of hospital information system for medical image information sharing

International Nuclear Information System (INIS)

Kim, Seon Chil; Kwon, Su Ja

2001-01-01

As the adoption of PACS and hospital information system among university hospitals and hospital level institutions grows bigger, the need of sharing and transferring medical information among medical institutions is rising. For the medical information, which is saved in the hospital medical system, to be transferred within the same hospital, domestic, or foreign medical institutions, a standard protocol is necessary. But realistically, most of the domestic hospitals do not abide by H7L which is the HIS standard and so, information transferring is not possible as of present. As such, the purpose of this research is to implement the information between HIS and PACS to an international standard by constructing HL7 messages through HL7 Interface, which will eventually make possible information transferring between different hospitals. Our research team has developed a method which will make the PACS equip hospitals that do not follow HL7 standard which will make possible to transfer information between HIS and PACS through HL7 Message. By constructing message files, which follow the form of HL7 Message in the HL7 Interface, they can be transferred to PACS through the ftp protocol. The realization of the HIS/OCS Interface through HL7 enables data transferring between domestic and foreign medical institutions possible by implementing the international standard in the PACS and HIS data transferring process. The HL7 that our research team has developed made patient data transfer between medical institutions possible. The Interface is for a specific system model and in order for the data transfer between different systems to be realized, interfaces that are fit for each system must be needed. If the Interface is improvised and implemented to each hospital's information system, the data sharing among medical institutions can be broadened

Specifications of Standards in Systems and Synthetic Biology: Status and Developments in 2017

Directory of Open Access Journals (Sweden)

Schreiber Falk

2018-03-01

Full Text Available Standards are essential to the advancement of Systems and Synthetic Biology. COMBINE provides a formal body and a centralised platform to help develop and disseminate relevant standards and related resources. The regular special issue of the Journal of Integrative Bioinformatics aims to support the exchange, distribution and archiving of these standards by providing unified, easily citable access. This paper provides an overview of existing COMBINE standards and presents developments of the last year.

[Wound information management system: a standardized scheme for acquisition, storage and management of wound information].

Science.gov (United States)

Liu, Hu; Su, Rong-jia; Wu, Min-jie; Zhang, Yi; Qiu, Xiang-jun; Feng, Jian-gang; Xie, Ting; Lu, Shu-liang

2012-06-01

To form a wound information management scheme with objectivity, standardization, and convenience by means of wound information management system. A wound information management system was set up with the acquisition terminal, the defined wound description, the data bank, and related softwares. The efficacy of this system was evaluated in clinical practice. The acquisition terminal was composed of the third generation mobile phone and the software. It was feasible to get access to the wound information, including description, image, and therapeutic plan from the data bank by mobile phone. During 4 months, a collection of a total of 232 wound treatment information was entered, and accordingly standardized data of 38 patients were formed automatically. This system can provide standardized wound information management by standardized techniques of acquisition, transmission, and storage of wound information. It can be used widely in hospitals, especially primary medical institutions. Data resource of the system makes it possible for epidemiological study with large sample size in future.

Quality parameters for a multimodal EEG/EMG/kinematic brain-computer interface (BCI aiming to suppress neurological tremor in upper limbs [v2; ref status: indexed, http://f1000r.es/3aq

Directory of Open Access Journals (Sweden)

Giuliana Grimaldi

2014-04-01

Full Text Available Tremor is the most common movement disorder encountered during daily neurological practice. Tremor in the upper limbs causes functional disability and social inconvenience, impairing daily life activities. The response of tremor to pharmacotherapy is variable. Therefore, a combination of drugs is often required. Surgery is considered when the response to medications is not sufficient. However, about one third of patients are refractory to current treatments. New bioengineering therapies are emerging as possible alternatives. Our study was carried out in the framework of the European project “Tremor” (ICT-2007-224051. The main purpose of this challenging project was to develop and validate a new treatment for upper limb tremor based on the combination of functional electrical stimulation (FES; which has been shown to reduce upper limb tremor with a brain-computer interface (BCI. A BCI-driven detection of voluntary movement is used to trigger FES in a closed-loop approach. Neurological tremor is detected using a matrix of EMG electrodes and inertial sensors embedded in a wearable textile. The identification of the intentionality of movement is a critical aspect to optimize this complex system. We propose a multimodal detection of the intentionality of movement by fusing signals from EEG, EMG and kinematic sensors (gyroscopes and accelerometry. Parameters of prediction of movement are extracted in order to provide global prediction plots and trigger FES properly. In particular, quality parameters (QPs for the EEG signals, corticomuscular coherence and event-related desynchronization/synchronization (ERD/ERS parameters are combined in an original algorithm which takes into account the refractoriness/responsiveness of tremor. A simulation study of the relationship between the threshold of ERD/ERS of artificial EEG traces and the QPs is also provided. Very interestingly, values of QPs were much greater than those obtained for the corticomuscular

Specifications of Standards in Systems and Synthetic Biology: Status and Developments in 2016

Directory of Open Access Journals (Sweden)

Schreiber Falk

2016-09-01

Full Text Available Standards are essential to the advancement of science and technology. In systems and synthetic biology, numerous standards and associated tools have been developed over the last 16 years. This special issue of the Journal of Integrative Bioinformatics aims to support the exchange, distribution and archiving of these standards, as well as to provide centralised and easily citable access to them.

Open Source, Open Standards, and Health Care Information Systems

Science.gov (United States)

2011-01-01

Recognition of the improvements in patient safety, quality of patient care, and efficiency that health care information systems have the potential to bring has led to significant investment. Globally the sale of health care information systems now represents a multibillion dollar industry. As policy makers, health care professionals, and patients, we have a responsibility to maximize the return on this investment. To this end we analyze alternative licensing and software development models, as well as the role of standards. We describe how licensing affects development. We argue for the superiority of open source licensing to promote safer, more effective health care information systems. We claim that open source licensing in health care information systems is essential to rational procurement strategy. PMID:21447469

75 FR 75186 - Interview Room Video System Standard Special Technical Committee Request for Proposals for...

Science.gov (United States)

2010-12-02

... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1534] Interview Room Video System Standard Special Technical Committee Request for Proposals for Certification and Testing Expertise... Interview Room Video System Standard and corresponding certification program requirements. This work is...

Adapting the CUAHSI Hydrologic Information System to OGC standards

Science.gov (United States)

Valentine, D. W.; Whitenack, T.; Zaslavsky, I.

2010-12-01

The CUAHSI Hydrologic Information System (HIS) provides web and desktop client access to hydrologic observations via water data web services using an XML schema called “WaterML”. The WaterML 1.x specification and the corresponding Water Data Services have been the backbone of the HIS service-oriented architecture (SOA) and have been adopted for serving hydrologic data by several federal agencies and many academic groups. The central discovery service, HIS Central, is based on an metadata catalog that references 4.7 billion observations, organized as 23 million data series from 1.5 million sites from 51 organizations. Observations data are published using HydroServer nodes that have been deployed at 18 organizations. Usage of HIS has increased by 8x from 2008 to 2010, and doubled in usage from 1600 data series a day in 2009 to 3600 data series a day in the first half of 2010. The HIS central metadata catalog currently harvests information from 56 Water Data Services. We collaborate on the catalog updates with two federal partners, USGS and US EPA: their data series are periodically reloaded into the HIS metadata catalog. We are pursuing two main development directions in the HIS project: Cloud-based computing, and further compliance with Open Geospatial Consortium (OGC) standards. The goal of moving to cloud-computing is to provide a scalable collaborative system with a simpler deployment and less dependence of hardware maintenance and staff. This move requires re-architecting the information models underlying the metadata catalog, and Water Data Services to be independent of the underlying relational database model, allowing for implementation on both relational databases, and cloud-based processing systems. Cloud-based HIS central resources can be managed collaboratively; partners share responsibility for their metadata by publishing data series information into the centralized catalog. Publishing data series will use REST-based service interfaces, like OData

78 FR 63408 - List of Approved Spent Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS® Cask System

Science.gov (United States)

2013-10-24

... Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System AGENCY: Nuclear...] Cask System listing within the ``List of Approved Spent Fuel Storage Casks'' to include Amendment No... Safety Analysis Report for the Standardized NUHOMS[supreg] Horizontal Modular Storage System for...

Development of radiation tolerant components for the Quench Protection System at CERN

Science.gov (United States)

Bitterling, O.; Denz, R.; Steckert, J.; Uznanski, S.

2016-01-01

This paper describes the results of irradiation campaigns with the high resolution Analog to Digital Converter (ADC) ADS1281. This ADC will be used as part of a revised quench detection circuit for the 600 A corrector magnets at the CERN Large Hadron Collider (LHC) . To verify the radiation tolerance of the ADC an irradiation campaign using a proton beam, applying doses up to 3,4 kGy was conducted. The resulting data and an analysis of the found failure modes is discussed in this paper. Several mitigation measures are described that allow to reduce the error rate to levels acceptable for operation as part of the LHC QPS.

Development of radiation tolerant components for the Quench Protection System at CERN

International Nuclear Information System (INIS)

Bitterling, O.; Denz, R.; Steckert, J.; Uznanski, S.

2016-01-01

This paper describes the results of irradiation campaigns with the high resolution Analog to Digital Converter (ADC) ADS1281. This ADC will be used as part of a revised quench detection circuit for the 600 A corrector magnets at the CERN Large Hadron Collider (LHC) . To verify the radiation tolerance of the ADC an irradiation campaign using a proton beam, applying doses up to 3,4 kGy was conducted. The resulting data and an analysis of the found failure modes is discussed in this paper. Several mitigation measures are described that allow to reduce the error rate to levels acceptable for operation as part of the LHC QPS

Standard hydrogen monitoring system-B operation and maintenance manual

International Nuclear Information System (INIS)

Bender, R.M.

1995-01-01

The purpose of this document is to provide information for the operation and maintenance of the Standards Hydrogen Monitoring System-B (SHMS-B) used in the 200E and 200W area tank farms on the Hanford site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. The primary function of the SHMS-B is to monitor specifically for hydrogen in the waste tank vapor space which may also contain unknown quantities of other gaseous constituents

Developing a Standard Method of Test for Packaged, Solid-Desiccant Based Dehumidification Systems

International Nuclear Information System (INIS)

Sand, J.R.

2001-01-01

A draft Method of Test (MOT) has been proposed for packaged, air-to-air, desiccant-based dehumidifier systems that incorporate a thermally-regenerated desiccant material for dehumidification. This MOT is intended to function as the ''system'' testing and rating compliment to the desiccant ''component'' (desiccant wheels and/or cassettes) MOT (ASHRAE 1998) and rating standard (ARI 1998) already adopted by industry. This draft standard applies to ''packaged systems'' that: Use desiccants for dehumidification of conditioned air for buildings; Use heated air for regeneration of the desiccant material; Include fans for moving process and regeneration air; May include other system components for filtering, pre-cooling, post-cooling, or heating conditioned air; and May include other components for humidification of conditioned air. The proposed draft applies to four different system operating modes depending on whether outdoor or indoor air is used for process air and regeneration air streams . Only the ''ventilation'' mode which uses outdoor air for both process and regeneration inlets is evaluated in this paper. Performance of the dehumidification system is presented in terms that would be most familiar and useful to designers of building HVAC systems to facilitate integration of desiccant equipment with more conventional hardware. Parametric performance results from a modified, commercial desiccant dehumidifier undergoing laboratory testing were used as data input to evaluate the draft standard. Performance results calculated from this experimental input, results from an error-checking/heat-balance verification test built into the standard, and estimated comparisons between desiccant and similarly performing conventional dehumidification equipment are calculated and presented. Some variations in test procedures are suggested to aid in analytical assessment of individual component performance

An IEC standard on quality assurance for diagnostic X-ray systems

International Nuclear Information System (INIS)

Boer, J.A. den

1985-01-01

A presentation is given of some characteristics of the International Electrotechnical Commission (IEC). This is followed by a short discussion of general aspects of quality assurance in the diagnostic department. From this discussion it becomes apparent to which aspects of quality assurance IEC can contribute. Within that framework a working group of Sub-Committee 62 is at present active in developing a standard on quality assurance for diagnostic X-ray systems. The standard will contain a set of constancy tests that is claimed to allow a balanced quality assurance programme. The democratic procedure of IEC should guarantee that the proposed standard gains wide acceptance. (author)

78 FR 63375 - List of Approved Spent Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS® Cask System

Science.gov (United States)

2013-10-24

... Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System AGENCY: Nuclear...] Cask System listing within the ``List of Approved Spent Fuel Storage Casks'' to include Amendment No..., Inc. Standardized NUHOMS[supreg] Cask System listing within the ``List of Approved Spent Fuel Storage...

Review of Special Standards in Quality Management Systems Audits in Automotive Production

Science.gov (United States)

Šurinová, Yulia

2013-12-01

Quality management systems (QMS) in automotive industry generally have several differences in comparison with other industrial branches. Different customers have their own specific requirements, including requirements for quality audits. Audits are one of the coretools of quality management to make the PDCA (Plan - Do - Check - Act) cycle work. As a matter of fact, compliance with ISO/TS 16949:2009 requirements is a condition for supplying the automotive industry. However, there are some standards which co-exist together with the ISO 9001 based management systems and technical specification for QMS in automotive ISO/TS16949. Which are those specific standards in automotive industry and what standard to use and why - those are the questions to be answered in this paper. The aim of the paper is to review what standards are used for audits implementation in automotive industry in the Slovak Republic, and why the organizations keep following those "extra" standards even if certification for ISO/TS 16949 is required by all the car makers. The paper is structured as follows: after short introduction to the topic and related terms, presented is our methodology. . In the third section, the achieved results are discussed. And finally, the principal findings of the paper, limitations and conclusions are presented.

Initial testing of a neutron activation analysis system by analysing standard reference materials

International Nuclear Information System (INIS)

Suhaimi Hamzah; Roslan Idris; Abdul Khalik Haji Wood; Che Seman Mahmood; Abdul Rahim Mohamad Noor.

1983-01-01

This paper describes the data acquisition and processing system in our laboratories (ND6600), the methods of activation analysis and the results obtained from our analysis of IAEA standard reference material (SL-l lake sediments and NBS coal ash 1632a). These standards were analysed in order to check the capability of the system, which was designed in such a way as to enable the user to independently collect and process data from multiple radiation detectors. (author)

Flight Standards Automation System -

Data.gov (United States)

Department of Transportation — FAVSIS supports Flight Standards Service (AFS) by maintaining their information on entities such as air carriers, air agencies, designated airmen, and check airmen....

Fast numerical algorithm for the linear canonical transform.

Science.gov (United States)

Hennelly, Bryan M; Sheridan, John T

2005-05-01

The linear canonical transform (LCT) describes the effect of any quadratic phase system (QPS) on an input optical wave field. Special cases of the LCT include the fractional Fourier transform (FRT), the Fourier transform (FT), and the Fresnel transform (FST) describing free-space propagation. Currently there are numerous efficient algorithms used (for purposes of numerical simulation in the area of optical signal processing) to calculate the discrete FT, FRT, and FST. All of these algorithms are based on the use of the fast Fourier transform (FFT). In this paper we develop theory for the discrete linear canonical transform (DLCT), which is to the LCT what the discrete Fourier transform (DFT) is to the FT. We then derive the fast linear canonical transform (FLCT), an N log N algorithm for its numerical implementation by an approach similar to that used in deriving the FFT from the DFT. Our algorithm is significantly different from the FFT, is based purely on the properties of the LCT, and can be used for FFT, FRT, and FST calculations and, in the most general case, for the rapid calculation of the effect of any QPS.

Business transactions and standards. Towards a system of concepts and a method for early problem identification in standard implementation projects

NARCIS (Netherlands)

Rukanova, B.D.

2005-01-01

To summarize, with respect to research question one we constructed a system of concepts, while in answer to research question two we proposed a method of how to apply this system of concepts in practice in order to identify potential problems in early stages of standard implementation projects.

Performance Measurement of Management System Standards Using the Balanced Scorecard

Directory of Open Access Journals (Sweden)

Jan Kopia

2017-11-01

Full Text Available Management system standards (MSS, such as ISO standards, TQM, etc. are widely-used standards adopted by millions of organizations worldwide. It is still an unclear question whether these standards are beneficial for an organization, besides the fact that they might be required or expected by law or customers. The question, whether MSS increase the efficiency, the output, or the performance of an organization is still discussed in scientific research. One reason might be that performance measurement itself is not fully understood or in constant development ranging from pure financial evaluations over intellectual capital rating to calculating of levels of environmental, social or economic expectations known as the Trible Bottom Line. The Balanced Scorecard is one possible solution for performance measurement on a strategic and operational level and therefore useful for the measurement of the influence of MSS within organizations. This study summarized current research in the field of performance measurement in the context of MSS and IMS and the use of BSC and quantitatively and qualitatively tests the usefulness of BSC in measuring the effect of MSSs using the Execution Premium. It was found that BSC is often used, that an average number of companies integrate their measurement initiatives of their MSSs into the BSC-process, and that a high integration of MSS into the BSC improves the organizational performance. This research is useful for researchers and practitioners in order to understand the benefits of the usage of the BSC in the context of MSS or Integrated Management Systems.

Standards in chestnut coppice system: cultural heritage or coltural requirement?

Directory of Open Access Journals (Sweden)

Manetti MC

2012-12-01

Full Text Available Standards in chestnut coppice system: cultural heritage or coltural requirement? This paper aims at evaluating the role of standards in chestnut coppices from a biological and functional perspective. In addition to a detailed analysis of Italian regulations on the issue, the technical definition of the term is analysed: (i as for the functional role of standards; (ii to assess whether the required functions are technically necessary and are being actually performed. In this contex, the results of an experimental trial are reported. The goal of the trial were to assess the shoots’ parameters, the stand productivity, the dynamics of canopy cover in coppices with or without standards. In 2001, at harvesting operations in a coppice aged 30 with standards managed by the local community, two experimental plots 2500 m2 each were established. The two theses being compared were: simple coppice and coppixce with standards (100 standards per hectare. The released standards were qualified immediately after final harvesting. Sprouting ability, growth pattern and stool vitality were surveyed in March 2004 (at age 2, in May 2008 (at age 6 and in April 2010 (at age 8. First results highlighted the evidence of statistically significant differences between the two thesis. The high number of standards effected negatively both vitality and growth pattern of the stools. Simple coppice recorded a lower shoot mortality, a higher diametrical growth and canopy cover degree as well; the heigth growth was, on the opposite, significantly lower. These results, although referred to a limited lifespan (1/3 of the rotation time and to one site only, underline productive, ecological and environmental benefits and as a consequence suggest the widening of the experimental network and the development of new, more relevant and consistent rules, making acceptable the simple coppice as a possible silvicultural choice to be applied to chestnut coppices.

Towards a Standardized e-Assessment System: Motivations, Challenges and First Findings

Directory of Open Access Journals (Sweden)

Denis Helic

2009-10-01

Full Text Available “Global Learning” with shared learning contents, resources, activities and goals is one of the contributions of Globalization. With the capability to use new Information and Communication Technologies (ICT it is a bit easier to have a technology based learning systems that enable learners to share the learning resources and possibilities. As a result many Learning Management Systems (LMS were developed with divers of platforms and approaches. Consequently, sharing learning resources and components has become a major challenge. E-assessment as a primary activity of any LMS is facing the same challenges and problems. In order to stand on this challenge people in the field of technology enhanced learning have recommended that LMS should conform to specific standards. This paper discuses this challenge, the consequences and limitations of standards in the modern learning settings. Moreover, it shows a service oriented framework for assessment which aims to make the e-assessment systems flexible and also to initiate the term of “Global Learning Assessment” with the possibility of sharing the e-assessment system components.

Domain management OSSs: bridging the gap between legacy and standards-based network management systems

Science.gov (United States)

Lemley, Todd A.

1996-11-01

The rapid change in the telecommunications environment is forcing carriers to re-assess not only their service offering, but also their network management philosophy. The competitive carrier environment has taken away the luxury of throwing technology at a problem by using legacy and proprietary systems and architectures. A more flexible management environment is necessary to effectively gain, and maintain operating margins in the new market era. Competitive forces are driving change which gives carriers more choices than those that are available in legacy and standards-based solutions alone. However, creating an operational support system (OSS) with this gap between legacy and standards has become as dynamic as the services which it supports. A philosophy which helps to integrate the legacy and standards systems is domain management. Domain management relates to a specific service or market 'domain,'and its associated operational support requirements. It supports a companies definition of its business model, which drives the definition of each domain. It also attempts to maximize current investment while injecting new technology available in a practical approach. The following paragraphs offer an overview of legacy systems, standards-based philosophy, and the potential of domain management to help bridge the gap between the two types of systems.

PROPOSAL METHODOLOGY OF THE SUBSYSTEM - INTERNAL STANDARDIZATION AS PART OF TQM SYSTEM

Directory of Open Access Journals (Sweden)

Elizabeta Mitreva

2012-09-01

Full Text Available Standardization in the management system becomes a key task of the managers and a priority issue for survival of every organization of this century. Besides the company's owner which is mostly concerned with the profit and fast multiplication of its invested capital, many other parties such as consumers, community, employees, deliverers and the society make a pressure in demanding. As of those demands the organization is to adapt its management system according the standards in order to be safe t hat the expectations will be fulfilled. However, to fulfill the standards in Europe and worldwide it is necessary to approach towards huge - radical changes in problem solving i.e. reengineering, new manner of consideration of causes and not as the so far known way - thinking over the consequences. Implementing this new TQM strategy means designing solidly documented quality system that covers every working process in a company and appears as a necessary base for successful usage of statistical process contr ol (SPC and efficient teamwork which otherwise in case of bad quality system will not be able to be set. In this manner it is guaranteed that the attitude of the top management is conducted; this attitude is consisted within the quality policy that create s a climate and information base whe re team work can be developed. This paper offers a proposal methodology for designing and implementation of internal standardization of TQM system in companies. This methodology is applicable in factory for reconstructio n of wagons and in a factory for confectionary production and has shown its efficiency and usage. In order to design the processes in line with the consumers/ clients content and at the same time to achieve profitability, it is necessary to reengineer the working processes

Standard Hydrogen Monitoring System-D operation and maintenance manual

International Nuclear Information System (INIS)

Schneider, T.C.

1997-01-01

The purpose of this document is to provide information for the operation and maintenance of the Standard Hydrogen Monitoring System-D (SHMS-D) used in the 200E and 200W area tank farms on the Hanford Site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. However, it does provide more information on the system than a Plant Operating Procedure. The intent here is that the system is started up by a technician or engineer who has completed tank farms training course No. 351405, and then the only actions performed by Operations will be routine log taking. If any problems not addressed by the operating procedure are encountered with the unit, engineering should be contacted

Standard hydrogen monitoring system - E operation and maintenance manual

International Nuclear Information System (INIS)

Schneider, T.C.

1997-01-01

The purpose of this document is to provide information for the operation and maintenance of the Standard Hydrogen Monitoring System- E (SHMS-E) used in the 200E and 20OW area tank farms on the Hanford Site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. However, it does provide more information on the system than a Plant Operating Procedure. The intent here is that the system is started up by a technician or engineer who has completed tank farms training course for SHMS, and then the only actions performed by Operations will be routine log taking. If any problems not addressed by the operating procedure are encountered with the unit, engineering should be contacted

40 CFR 264.1033 - Standards: Closed-vent systems and control devices.

Science.gov (United States)

2010-07-01

... determined by dividing the volumetric flow rate (in units of standard temperature and pressure), as.... The system shall be equipped with at least one pressure gauge or other pressure measurement device...

Analysis of Indonesian educational system standard with KSIM cross-impact method

Science.gov (United States)

Arridjal, F.; Aldila, D.; Bustamam, A.

2017-07-01

The Result of The Programme of International Student Assessment (PISA) on 2012 shows that Indonesia is on 64'th position from 65 countries in Mathematics Mean Score. The 2013 Learning Curve Mapping, Indonesia is included in the 10th category of countries with the lowest performance on cognitive skills aspect, i.e. 37'th position from 40 countries. Competency is built by 3 aspects, one of them is cognitive aspect. The low result of mapping on cognitive aspect, describe the low of graduate competences as an output of Indonesia National Education System (INES). INES adopting a concept Eight Educational System Standards (EESS), one of them is graduate competency standard which connected directly with Indonesia's students. This research aims is to model INES by using KSIM cross-impact. Linear regression models of EESS constructed using the accreditation national data of Senior High Schools in Indonesia. The results then interpreted as impact value on the construction of KSIM cross-impact INES. The construction is used to analyze the interaction of EESS and doing numerical simulation for possible public policy in the education sector, i.e. stimulate the growth of education staff standard, content, process and infrastructure. All simulations of public policy has been done with 2 methods i.e with a multiplier impact method and with constant intervention method. From numerical simulation result, it is shown that stimulate the growth standard of content in the construction KSIM cross-impact EESS is the best option for public policy to maximize the growth of graduate competency standard.

Environmental protection standards - from the point of view of systems analysis

Energy Technology Data Exchange (ETDEWEB)

Becker, K

1978-11-01

A project of the International Institute of Applied Systems Analysis (IIASA) in Laxenburg castle near Vienna is reviewed where standards for environmental protection are interpreted from the point of view of systems analysis. Some examples are given to show how results are influenced not only by technical and economic factors but also by psychological and political factors.

Environmental protection standards - from the point of view of systems analysis

International Nuclear Information System (INIS)

Becker, K.

1978-01-01

A project of the International Institute of Applied Systems Analysis (IIASA) in Laxenburg castle near Vienna is reviewed where standards for environmental protection are interpreted from the point of view of systems analysis. Some examples are given to show how results are influenced not only by technical and economic factors but also by psychological and political factors. (orig.) [de

Quality assurance: Importance of systems and standard operating procedures.

Science.gov (United States)

Manghani, Kishu

2011-01-01

It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

Quality assurance: Importance of systems and standard operating procedures

Directory of Open Access Journals (Sweden)

Kishu Manghani

2011-01-01

Full Text Available It is mandatory for sponsors of clinical trials and contract research organizations alike to establish, manage and monitor their quality control and quality assurance systems and their integral standard operating procedures and other quality documents to provide high-quality products and services to fully satisfy customer needs and expectations. Quality control and quality assurance systems together constitute the key quality systems. Quality control and quality assurance are parts of quality management. Quality control is focused on fulfilling quality requirements, whereas quality assurance is focused on providing confidence that quality requirements are fulfilled. The quality systems must be commensurate with the Company business objectives and business model. Top management commitment and its active involvement are critical in order to ensure at all times the adequacy, suitability, effectiveness and efficiency of the quality systems. Effective and efficient quality systems can promote timely registration of drugs by eliminating waste and the need for rework with overall financial and social benefits to the Company.

CLAIM (CLinical Accounting InforMation)--an XML-based data exchange standard for connecting electronic medical record systems to patient accounting systems.

Science.gov (United States)

Guo, Jinqiu; Takada, Akira; Tanaka, Koji; Sato, Junzo; Suzuki, Muneou; Takahashi, Kiwamu; Daimon, Hiroyuki; Suzuki, Toshiaki; Nakashima, Yusei; Araki, Kenji; Yoshihara, Hiroyuki

2005-08-01

With the evolving and diverse electronic medical record (EMR) systems, there appears to be an ever greater need to link EMR systems and patient accounting systems with a standardized data exchange format. To this end, the CLinical Accounting InforMation (CLAIM) data exchange standard was developed. CLAIM is subordinate to the Medical Markup Language (MML) standard, which allows the exchange of medical data among different medical institutions. CLAIM uses eXtensible Markup Language (XML) as a meta-language. The current version, 2.1, inherited the basic structure of MML 2.x and contains two modules including information related to registration, appointment, procedure and charging. CLAIM 2.1 was implemented successfully in Japan in 2001. Consequently, it was confirmed that CLAIM could be used as an effective data exchange format between EMR systems and patient accounting systems.

A holistic strategy for quality and safety control of traditional Chinese medicines by the "iVarious" standard system.

Science.gov (United States)

Chen, Anzhen; Sun, Lei; Yuan, Hang; Wu, Aiying; Lu, Jingguang; Ma, Shuangcheng

2017-10-01

An effective quality control system is the key to ensuring the quality, safety and efficacy of traditional Chinese medicines (TCMs). However, the current quality standard research lacks the top-design and systematic design, mostly based on specific technologies or evaluation methods. To resolve the challenges and questions of quality control of TCMs, a brand-new quality standard system, named "iVarious", was proposed. The system comprises eight elements in a modular format. Meaning of every element was specifically illustrated via corresponding research instances. Furthermore, frankincense study was taken as an example for demonstrating standards and research process, based on the "iVarious" system. This system highlighted a holistic strategy for effectiveness, security, integrity and systematization of quality and safety control standards of TCMs. The establishment of "iVarious" integrates multi-disciplinary technologies and progressive methods, basis elements and key points of standard construction. The system provides a novel idea and technological demonstration for regulation establishment of TCMs quality standards.

Effects of setting new source performance standards for fluidized-bed combustion systems

Energy Technology Data Exchange (ETDEWEB)

1978-02-01

This study was undertaken for the US Environmental Protection Agency to examine the potential consequences of revisions in New Source Performance Standards (NSPS) on fluidized-bed combustor-based steam electric generators of greater than 250,000,000 Btu. A study of the appropriateness and differential effects of alternate regulatory approaches to the standards-setting process was made. Problems dealing with an emerging technology such as fluidized-bed combustion were emphasized. Finally, an examination was made of the potential benefits of fluidized-bed combustion (FBC) systems relative to conventional coal-fired systems equipped with scrubbers. Information is included on the relative advantages and disadvantages of utility-sized fluidized-bed combustors, the technical consequences of NSPS alternatives, policy implications concerning NSPS for steam-electric generators, and cost models for atmospheric and pressurized FBC systems. (LCL)

40 CFR 60.254 - Standards for coal processing and conveying equipment, coal storage systems, transfer and loading...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for coal processing and conveying equipment, coal storage systems, transfer and loading systems, and open storage piles. 60.254... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Coal Preparation...

Evaluating spoken dialogue systems according to de-facto standards: A case study

NARCIS (Netherlands)

Möller, S.; Smeele, P.; Boland, H.; Krebber, J.

2007-01-01

In the present paper, we investigate the validity and reliability of de-facto evaluation standards, defined for measuring or predicting the quality of the interaction with spoken dialogue systems. Two experiments have been carried out with a dialogue system for controlling domestic devices. During

A CAMAC-system crate interface based on EUR 6100 standards

International Nuclear Information System (INIS)

Wolstenholme, P.; Verelst, H.; Parker, C.R.C.B.

1980-01-01

The particle beams in the Intersecting Storage Rings of the CERN accelerator are controlled by means of a CAMAC Branch Highway and three CAMAC Serial Highway Systems. The highway controllers, housed in system crates, are driven by crate controllers interfaced to the control computers. The crate controllers are implemented as auxiliary controllers and are PROM based to allow N, A and F to be generated from a small zone of computer addresses and are largely transparent to the host computer. The concept has enabled standard modules and techniques taken from the Serial Highway to be adopted for use in system crates. (Auth.)

Development of standard logic network for PWR NSSS system design

International Nuclear Information System (INIS)

Chung, Moon Kyu; Lee, Byeong Ryeong; Lee, Pan Kwon; Lee, Hae Joon; Park, Joon Won; Song, Tae Gil; Kim, Dong Hui; Choi, Hyeon Ho

1993-05-01

The self-reliance of NSSS System Design is required not only the design capability to perform the system design but also the management capability to control the resource and time for the Project effectively. The purpose of this study is to develop the simplified standard Logic Network that is scheduled on the time and resource using the PERT/CPM method. That is mainly focused on Ulchin 3, 4 Project. We prepare the management tool of NSSS System Design project. And we can utilize it as a reference tool for the similar project which are complex and long term in a next project. (Author)

An integrated methodology to develop a standard for landslide early warning systems

OpenAIRE

Fathani, Teuku Faisal; Karnawati, Dwikorita; Wilopo, Wahyu

2016-01-01

Landslides are one of the most widespread and commonly occurring natural hazards. In regions of high vulnerability, these complex hazards can cause significant negative social and economic impacts. Considering the worldwide susceptibility to landslides, it is necessary to establish a standard for early warning systems specific to landslide disaster risk reduction. This standard would provide guidance in conducting landslide detection, prediction, interpretation, and response...

Standard Practice for Quality Management Systems for Nondestructive Testing Agencies

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This practice covers general requirements for the establishment and maintenance of a quality management system for agencies engaged in nondestructive testing (NDT). 1.2 This practice utilizes criteria contained in Practice E 543. 1.3 This practice utilizes criteria contained in American National Standard ANSI/ISO/ASQ Q9001–2000, Quality management systems—Requirements. 1.4 This practice recognizes the importance of establishing minimum safety criteria. 1.5 The use of SI or inch-pound units, or combinations thereof, will be the responsibility of the technical committee whose standards are referred to in this standard. 1.6 This practice does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this practice to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

49 CFR 179.400-4 - Insulation system and performance standard.

Science.gov (United States)

2010-10-01

... specification— (1) Standard Heat Transfer Rate (SHTR), expressed in Btu/day/lb of water capacity, means the rate of heat transfer used for determining the satisfactory performance of the insulation system of a..., whichever is greater. (5) Calculated heat transfer rate. The calculated heat transfer rate (CHTR) is...

Using a standards committee to design practical procedure system improvements

International Nuclear Information System (INIS)

Grider, D.A.; Plung, D.

1993-01-01

In the post-Three Mile Island (TMI) environment, numerous reports have been issued on how to improve the quality of procedures used at government and commercial nuclear facilities. The studies tend to be long on what is wrong with existing procedures and short on practical directions on how to fix those faults. Few of these studies have been conducted by practitioners with full-time procedure-managing or procedure writing experience. None of these studies go into detail on how to improve the procedure system itself. Over the last 10 yr, various nuclear facilities within the US Department of Energy (DOE) have carried out individual programs to develop procedures that meet post-TMI standards. However, ∼2 yr ago, DOE formed a Procedures Standards Committee to advise DOE in developing a set of post-TMI guidelines that could be consistently applied throughout all DOE nuclear facilities. The committee has achieved not only its original mission by producing a series of integrated guidance documents but has also evolved a systems approach to procedures management that sets new standards for procedure quality and efficiency. As members of this committee, the authors want to describe what has made the group's approach so successful. The lessons learned may be translatable to a wide range of government and commercial industry procedure programs

Standard Guide for On-Site Inspection and Verification of Operation of Solar Domestic Hot Water Systems

CERN Document Server

American Society for Testing and Materials. Philadelphia

1987-01-01

1.1 This guide covers procedures and test methods for conducting an on-site inspection and acceptance test of an installed domestic hot water system (DHW) using flat plate, concentrating-type collectors or tank absorber systems. 1.2 It is intended as a simple and economical acceptance test to be performed by the system installer or an independent tester to verify that critical components of the system are functioning and to acquire baseline data reflecting overall short term system heat output. 1.3 This guide is not intended to generate accurate measurements of system performance (see ASHRAE standard 95-1981 for a laboratory test) or thermal efficiency. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine th...

Standards for the user interface - Developing a user consensus. [for Space Station Information System

Science.gov (United States)

Moe, Karen L.; Perkins, Dorothy C.; Szczur, Martha R.

1987-01-01

The user support environment (USE) which is a set of software tools for a flexible standard interactive user interface to the Space Station systems, platforms, and payloads is described in detail. Included in the USE concept are a user interface language, a run time environment and user interface management system, support tools, and standards for human interaction methods. The goals and challenges of the USE are discussed as well as a methodology based on prototype demonstrations for involving users in the process of validating the USE concepts. By prototyping the key concepts and salient features of the proposed user interface standards, the user's ability to respond is greatly enhanced.

75 FR 61413 - Notice of Availability of Biotechnology Quality Management System Audit Standard and Evaluation...

Science.gov (United States)

2010-10-05

...] Notice of Availability of Biotechnology Quality Management System Audit Standard and Evaluation of... the public that the Animal and Plant Health Inspection Service has developed an audit standard for its biotechnology compliance assistance program. The audit standard, which was made available in draft form for...

Monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors

International Nuclear Information System (INIS)

Stanc, S.; Repa, M.

2001-01-01

Description of a monitoring system for accuracy and reliability characteristics of standard temperature measurements in WWER-440 reactors and benefits obtained from its use are shown in the presentation. As standard reactor temperature measurement, coolant temperature measurement at fuel assembly outlets and in loops, entered into the In-Reactor Control System , are considered. Such systems have been implemented at two V-230 reactors and are under implementation at other four V-213 reactors. (Authors)

EXPERIENCE OF IMPLEMENTATION OF THE LABOR PROTECTION CONTROL SYSTEM AT RUP «BMZ» IN ACCORDANCE WITH INTERNATIONAL STANDARDS OHSAS 180001 AND STATE STANDARD STB 18001

Directory of Open Access Journals (Sweden)

I. N. Zhuk

2010-01-01

Full Text Available Experience of introduction of the control system by labour protection at RUP «BMZ» in accordance with international standard OHSAS 18001 and State standard STB 18001 is described.

Medicaid program; Medicaid Management Information Systems; performance standards--HCFA. General notice.

Science.gov (United States)

1983-05-31

The purpose of this notice is to respond to the comments we received on the Medicaid Management Information Systems Performance Standards that we published in a notice with comment period on June 30, 1981 (46 FR 33653).

75 FR 52528 - Mandatory Reliability Standards for the Bulk-Power System; Notice of Technical Conference

Science.gov (United States)

2010-08-26

...] Mandatory Reliability Standards for the Bulk-Power System; Notice of Technical Conference August 19, 2010... Order No. 693 the Commission approved Reliability Standard BAL-003-0 as mandatory and enforceable and directed the ERO to develop a modification to BAL-003-0 through the Reliability Standards development...

78 FR 78693 - List of Approved Spent Fuel Storage Casks: Transnuclear, Inc. Standardized NUHOMS® Cask System

Science.gov (United States)

2013-12-27

... Storage Casks: Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System AGENCY: Nuclear Regulatory... storage regulations by revising the Transnuclear, Inc. Standardized NUHOMS[supreg] Cask System listing within the ``List of Approved Spent Fuel Storage Casks'' to include Amendment No. 11 to Certificate of...

ETV Program Report: Coatings for Wastewater Collection Systems - Standard Cement Materials, Epoxy Coating 4553

Science.gov (United States)

The Standard Cement Materials, Inc. Standard Epoxy Coating 4553™ (SEC 4553) epoxy coating used for wastewater collection system rehabilitation was evaluated by EPA’s Environmental Technology Verification Program under laboratory conditions at the Center for Innovative Grouting Ma...

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation method of the genetic testing system (Separate volume); 1999 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka (bessatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The separate volume included the proceedings of the re-consignee joint meeting on the standardization of evaluation method of the genetic testing system, the proceedings/data of the meeting of the committee of the standardization of evaluation method of the genetic testing system, etc. The data of the meeting are about a plan to execute the standardization of evaluation method of the genetic testing system, standardization of forms for reporting the results of the genetic test, a trial guideline for standardization of the genetic testing, standardization of evaluation method of the genetic testing system, etc. Moreover, the volume included 11 literature papers overseas on the above-mentioned themes, 'reports on the surveys in Europe and the U.S. on the standardization of evaluation method of the genetic testing system,' etc. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation method of the genetic testing system (Separate volume); 1999 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka (bessatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The separate volume included the proceedings of the re-consignee joint meeting on the standardization of evaluation method of the genetic testing system, the proceedings/data of the meeting of the committee of the standardization of evaluation method of the genetic testing system, etc. The data of the meeting are about a plan to execute the standardization of evaluation method of the genetic testing system, standardization of forms for reporting the results of the genetic test, a trial guideline for standardization of the genetic testing, standardization of evaluation method of the genetic testing system, etc. Moreover, the volume included 11 literature papers overseas on the above-mentioned themes, 'reports on the surveys in Europe and the U.S. on the standardization of evaluation method of the genetic testing system,' etc. (NEDO)

Working out the standards for nuclear power aging management implementation (PLM Standards)

International Nuclear Information System (INIS)

Miyano, Hiroshi

2008-01-01

Background of preparation of standards, preparation of standards for development of nuclear power aging management technologies, revision of PLM (Product Lifecycle Management) standards, and problems of PLM standards are stated. The placement of social needs, scheme, the standards system, preparation of rules and standards, and practical use of them by road map are illustrated and explained. Relation between the safety regulations and examination standards, and development and preparation of standards system are outlined. The nuclear power plant aging management and the maintenance control are provided by many rules and standards. PLM standards defines the aging phenomena and extracts the measurements and reflects them on the usual maintenance flow under the long term maintenance program. New examination system constructs the usual maintenance and the maintenance based on the aging management and long term maintenance program. Outline and construction of PLM standards are explained with notes and additional books. (S.Y.)

25 CFR 547.15 - What are the minimum technical standards for electronic data communications between system...

Science.gov (United States)

2010-04-01

... communications between system components? This section provides minimum standards for electronic data... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum technical standards for electronic data communications between system components? 547.15 Section 547.15 Indians NATIONAL INDIAN GAMING...

Key elements on implementing an occupational health and safety management system using ISO 45001 standard

Directory of Open Access Journals (Sweden)

Darabont Doru Costin

2017-01-01

Full Text Available Occupational health and safety (OHS management system is one of the main elements of the company’s general management system. During last decade, Romanian companies gained a valuable experience on implementing this type of management systems, using OHSAS 18001 referential and standard. However, the projected release of the ISO 45001 represents a new approach which requires the companies to take in consideration new key elements for a successful implementation of the OHS management system. The aim of the paper is to identify and analyse these key elements, by integration of the following issues: standard requirements, Romanian OHS legislation and good practice examples, including the general control measures for new and emerging risks such as psycho-social risks, workforce ageing and new technologies. The study results represent an important work instrument for each company interested to implement or upgrade its OHS management system using ISO 45001 standard and could be used regardless the company size or activity domain.

A wearable point-of-care system for home use that incorporates plug-and-play and wireless standards.

Science.gov (United States)

Yao, Jianchu; Schmitz, Ryan; Warren, Steve

2005-09-01

A point-of-care system for continuous health monitoring should be wearable, easy to use, and affordable to promote patient independence and facilitate acceptance of new home healthcare technology. Reconfigurability, interoperability, and scalability are important. Standardization supports these requirements, and encourages an open market where lower product prices result from vendor competition. This paper first discusses candidate standards for wireless communication, plug-and-play device interoperability, and medical information exchange in point-of-care systems. It then addresses the design and implementation of a wearable, plug-and-play system for home care which adopts the IEEE 1073 Medical Information Bus (MIB) standards, and uses Bluetooth as the wireless communication protocol. This standards-based system maximizes user mobility by incorporating a three-level architecture populated by base stations, wearable data loggers, and wearable sensors. Design issues include the implementation of the MIB standards on microcontroller-driven embedded devices, low power consumption, wireless data exchange, and data storage and transmission in a reconfigurable body-area network.

A holistic strategy for quality and safety control of traditional Chinese medicines by the “iVarious” standard system

Directory of Open Access Journals (Sweden)

Anzhen Chen

2017-10-01

Full Text Available An effective quality control system is the key to ensuring the quality, safety and efficacy of traditional Chinese medicines (TCMs. However, the current quality standard research lacks the top-design and systematic design, mostly based on specific technologies or evaluation methods. To resolve the challenges and questions of quality control of TCMs, a brand-new quality standard system, named “iVarious”, was proposed. The system comprises eight elements in a modular format. Meaning of every element was specifically illustrated via corresponding research instances. Furthermore, frankincense study was taken as an example for demonstrating standards and research process, based on the “iVarious” system. This system highlighted a holistic strategy for effectiveness, security, integrity and systematization of quality and safety control standards of TCMs. The establishment of “iVarious” integrates multi-disciplinary technologies and progressive methods, basis elements and key points of standard construction. The system provides a novel idea and technological demonstration for regulation establishment of TCMs quality standards.

Investigations on international standardization of environmental management systems. 3; Kankyo kanri system no kokusai hyojunka ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Japan as an ISO member country identifies the state of discussions in the environmental management standard deliberation committee at ISO. Investigations were performed on international standardization of environmental management systems for the purpose of participating and cooperating in preparing and establishing international standards related to environmental management, and playing part in working, solving and improving environmental problems. Under the circumstances that environmental problems are drawing worldwide interest, the International Organization for Standardization (ISO) has been carrying out since 1993 deliberations on environmental management standards to institutionalize environmental management rules to check effects of business activities on the environment. The International Organization for Standardization/Environmental Management Technical Committee (ISO/TC207) was installed, at which series number of 1400 order was allotted for environmental management related standards, and major standards have come to a final stage of standard formulation at the TC207 Oslo conference in June 1995. In Japan, the Ministry of International Trade and Industry has established an environmental management standard deliberation committee composed of people of experience or academic standing to advance discussions on how the environmental management should be in business entities through deliberations on ISO standards.

Improved safety of the system 80+TM standard plants design through increased diversity and redundancy of safety systems

International Nuclear Information System (INIS)

Matzie, Regis A.; Carpentino, Frederick L.; Robertson, James E.

1996-01-01

Safely systems in the System 80+ TM Standard Plant are designed with more redundancy, diversity and simplicity than earlier nuclear power plant designs. These gains were accomplished by an evolutionary process that preserved the desirable and proven features in currently operating nuclear plants, while improving reliability and defense-in-depth. The System 80+ safety systems are the primary contributors to a core damage frequency that is more than 100 times lower than 1980's vintage U. S. designs, including the predecessor System 80 R standard nuclear steam supply system (NSSS) design. The System 80+ design includes significant improvements to the safety injection system, emergency feedwater system, shutdown cooling system, containment spray system, reactor coolant gas vent system, and to their vital support systems. These improvements enhance performance for traditional design basis events and significantly reduce the probability of a severe accident. The System 80+ design also incorporates safety systems to mitigate a severe accident. The added systems include the rapid depressurization system, the in-containment refueling water storage tank, the cavity flooding system. These systems fully address the U. S. Nuclear Regulatory Commission's (US NRC) severe accident policy. The System 80+ safety systems are integrated with the System 80+ Nuclear Island (NI) design. The NI general arrangement provides quadrant separation of the safety systems for protection from fire and flooding, and large equipment pull spaces and lay down areas for maintenance. This paper will describe the System 80+ safety systems advanced design features, the improved accident prevention and mitigation capabilities, and startup, operating and maintenance benefits

A case study: forming an effective quality management system according to ISO 9000 standards

OpenAIRE

Zağyapan, Orhan

1995-01-01

Ankara : The Faculty of Management and the Graduate School of Business Administration of Bilkent Univ., 1995. Thesis (Master's) -- Bilkent University, 1995. Includes bibliographical references leaves 87-88 In today's world, companies which adopt themselves to certain internationally recognized standards are one step ahead of their competitors. ISO 9000 Quality System Standards captured the most attention among all. The aim of the standard is to provide an international bench...

Correlation study among the International Atomic Energy Agency standards and market standards on management system applicable to a UF6 conversion plant operation

International Nuclear Information System (INIS)

Oliveira, Dirceu Paulo de

2008-01-01

The Agency - International Atomic Energy Agency (IAEA), following the market trend of the management system integration, has decided to revise the quality assurance standards - IAEA 50-C/SG-Q publishing, in 2006, the standard on Management System (MS). IAEA GS-R-3 and its IAEA GS-G-3.1 guide. Also, the IAEA is about to publish a supplementary guide - IAEA DS349, which consider the integration of several functions involved in management of nuclear facilities, such as: safety, health, environmental and quality, ensuring that nuclear safety is not compromised. Conversion plants of 'Yellowcake' in UF 6 use and process radioactive materials, as well as other substances normally found in the chemical conventional industry, inserting themselves in the organization profile that require a high pattern of definition, implementation and continuous improvement of their MS and, therefore, should consider an approach of management integrated system (MIS). Taking a UF 6 conversion plant as focus, the correlation was performed among the Agency MS standards and those of the market - ISO 9001, ISO 14001 and OHSAS 18001, as well as with the Agency drafts standards on safety (DS316 and DS344), concluding that, in structuring an MIS, in compliance with the Agency MS standards, except for some adjustments, the ISO 9001, ISO 14001, and OHSAS 18001 are going to be met. On the other hand, the structuring of MIS should identify other requirements on safety, health and environmental, which also consider the conventional chemical and industrial characteristics that are out of the scope (ionizing radiation) of the safety standards of the Agency. The research proposes a documental procedure for a MIS applicable to this plant, providing elements for rationalization and contents of the identified documentation, for the promotion of the integration of the considered MS functions. (author)

40 CFR 280.20 - Performance standards for new UST systems.

Science.gov (United States)

2010-07-01

..., or spills and overfills for as long as the UST system is used to store regulated substances, all... of Canada CAN4-S603-M85, “Standard for Steel Underground Tanks for Flammable and Combustible Liquids... Flammable and Combustible Liquids,” and CAN4-S631-M84, “Isolating Bushings for Steel Underground Tanks...

An automated LS(β)- NaI(Tl)(γ) coincidence system as absolute standard for radioactivity measurements.

Science.gov (United States)

Joseph, Leena; Das, A P; Ravindra, Anuradha; Kulkarni, D B; Kulkarni, M S

2018-07-01

4πβ-γ coincidence method is a powerful and widely used method to determine the absolute activity concentration of radioactive solutions. A new automated liquid scintillator based coincidence system has been designed, developed, tested and established as absolute standard for radioactivity measurements. The automation is achieved using PLC (programmable logic controller) and SCADA (supervisory control and data acquisition). Radioactive solution of 60 Co was standardized to compare the performance of the automated system with proportional counter based absolute standard maintained in the laboratory. The activity concentrations determined using these two systems were in very good agreement; the new automated system can be used for absolute measurement of activity concentration of radioactive solutions. Copyright © 2018. Published by Elsevier Ltd.

IEEE standard for design qualification of safety systems equipment used in nuclear power generating stations

International Nuclear Information System (INIS)

Anon.

1980-01-01

This standard is written to serve as a general standard for qualification of all types of safety systems equipment, mechanical and instrumentation as well as electrical. It also establishes principles and procedures to be followed in preparing specific safety systems equipment standards. Guidance for qualifying specific safety systems equipment may be found in various specific equipment qualification standards that are now available or are being prepared. It is required that safety systems equipment in nuclear power generating stations meet or exceed its performance requirements throughout its installed life. This is accomplished by a disciplined program of design qualification and quality assurance of design, production, installation, maintenance and surveillance. This standard is for the design qualification section of the program only. Design qualification is intended to demonstrate the capability of the equipment design to perform its safety function(s) over the expected range of normal, abnormal, design basis event, post design basis event, and in-service test conditions. Inherent to design qualification is the requirement for demonstration, within limitations afforded by established technical state-of-the-art, that in-service aging throughout the qualified life established for the equipment will not degrade safety systems equipment from its original design condition to the point where it cannot perform its required safety function(s), upon demand. The above requirement reflects the primary role of design qualification to provide reasonable assurance that design- and age-related common failure modes will not occur during performance of safety function(s) under postulated service conditions

78 FR 49663 - Enhanced Risk Management Standards for Systemically Important Derivatives Clearing Organizations

Science.gov (United States)

2013-08-15

... COMMODITY FUTURES TRADING COMMISSION 17 CFR Part 39 RIN 3038-AC98 Enhanced Risk Management...'') is adopting final regulations to implement enhanced risk management standards for systemically..., strengthen the risk management practices of DCOs, and increase overall confidence in the financial system by...

Establishment of a tandem ionization chamber system in standard mammography beams

International Nuclear Information System (INIS)

Silva, Jonas O. da; Caldas, L.V.E.

2011-01-01

A double-faced tandem ionization chamber system was developed at the Calibration Laboratory of IPEN. It has different collecting electrode materials: aluminium and graphite. The response repeatability and reproducibility and the energy dependence test of this tandem ionization chamber were evaluated. The chamber response stability is within the ±3% limit recommended in international standards. The energy dependence test of the ionization chamber system using the tandem curve obtained, presented agreement with literature results. (author)

A Standardized Evaluation System for Decadal Climate Prediction

Science.gov (United States)

Kadow, C.; Cubasch, U.

2012-12-01

The evaluation of decadal prediction systems is a scientific challenge as well as a technical challenge in the climate research. The major project MiKlip (www.fona-miklip.de) for medium-term climate prediction funded by the Federal Ministry of Education and Research in Germany (BMBF) has the aim to create a model system that can provide reliable decadal forecasts on climate and weather. The model system to be developed will be novel in several aspects, with great challenges for the methodology development. This concerns especially the determination of the initial conditions, the inclusion into the model of processes relevant to decadal predictions, the increase of the spatial resolution through regionalisation, the improvement or adjustment of statistical post-processing, and finally the synthesis and validation of the entire model system. Therefore, a standardized evaluation system will be part of the MiKlip system to validate it - developed by the project 'Integrated data and evaluation system for decadal scale prediction' (INTEGRATION). The presentation gives an overview of the different linkages of such a project, shows the different development stages and gives an outlook for users and possible end users in climate service. The technical interface combines all projects inside of MiKlip and invites them to participate in a common evaluation system. The system design and the validation strategy from a standalone tool in the beginning to a user friendly web based system using GRID technologies to an integrated part of the operational MiKlip system for industry and society will give the opportunity to enhance the MiKlip strategy. First results of different possibilities of such a system will be shown to present the scientific background through Taylor diagrams, ensemble skill scores and e.g. climatological means to show the usability and possibilities of MiKlip and the INTEGRATION project.

Calibration Standards for Surface Topography Measuring Systems down to Nanometric Range

DEFF Research Database (Denmark)

Trumpold, H.; De Chiffre, Leonardo; Andreasen, Jan Lasson

compression and injection moulded plastic negatives and Ni-negatives have been made from which again Ni-positives were produced. The replication processes showed negligible deviations from the Pt and Pa values compared to the primary standards. An important prerequisite is the cleanliness of the surfaces......Background For the precise and accurate measurement of surface topography a whole range of surface detection systems is available. With their application in research and production problems arise due to the lack of traceable standard artefacts for the instrument calibration in X, Y and Z directions...... and for the calibration of filters. Existing ISO standards on calibration specimens are inadequate and limited in that they only cover contacting instruments and only partially the measuring ranges for these instruments. The whole range of non-contacting instruments are not covered despite their increasing use...

A pilot study of planar coil based magnetic stimulation using acute hippocampal slice in mice.

Science.gov (United States)

Park, H J; Kang, H K; Wang, M; Jo, J; Chung, E; Kim, S

2017-07-01

Micromagnetic stimulation using small-sized implantable coils has recently been studied. The main advantage of this method is that it can provide sustainable stimulation performance even if a fibrotic encapsulation layer is formed around the implanted coil by inflammation response, because indirectly induced currents are used to induce neural responses. In previous research, we optimized the geometrical and control parameters used in implantable magnetic stimulation. Based on those results, we fabricated the planar coil and studied the LTP effect in the hippocampal slice by two different magnetic stimulation protocols using the quadripulse stimulation (QPS) pattern. We found that direct magnetic stimulation (DMS) induced insignificant LTP effect and priming magnetic stimulation (PMS) occluded LTP effect after tetanic stimulation, when QPS patterned magnetic stimulation with 1 A current pulse was applied to the planar coil.

Condition Assessment Survey (CAS) Program. Deficiency standards and inspections methods manual: Volume 11, 0.11 Specialty systems

Energy Technology Data Exchange (ETDEWEB)

1993-05-01

General information is presented for asset determinant factor/CAS repair codes/CAS cost factors; guide sheet tool & material listing; testing methods; inspection frequency; standard system design life tables; system work breakdown structure; and general system/material data. Deficiency standards and inspection methods are presented for canopies; loading dock systems; tanks; domes (bulk storage, metal framing); louvers & vents; access floors; integrated ceilings; and mezzanine structures.

Development of a consensus standard for verification and validation of nuclear system thermal-fluids software

International Nuclear Information System (INIS)

Harvego, Edwin A.; Schultz, Richard R.; Crane, Ryan L.

2011-01-01

With the resurgence of nuclear power and increased interest in advanced nuclear reactors as an option to supply abundant energy without the associated greenhouse gas emissions of the more conventional fossil fuel energy sources, there is a need to establish internationally recognized standards for the verification and validation (V and V) of software used to calculate the thermal–hydraulic behavior of advanced reactor designs for both normal operation and hypothetical accident conditions. To address this need, ASME (American Society of Mechanical Engineers) Standards and Certification has established the V and V 30 Committee, under the jurisdiction of the V and V Standards Committee, to develop a consensus standard for verification and validation of software used for design and analysis of advanced reactor systems. The initial focus of this committee will be on the V and V of system analysis and computational fluid dynamics (CFD) software for nuclear applications. To limit the scope of the effort, the committee will further limit its focus to software to be used in the licensing of High-Temperature Gas-Cooled Reactors. Although software verification will be an important and necessary part of the standard, much of the initial effort of the committee will be focused on the validation of existing software and new models that could be used in the licensing process. In this framework, the Standard should conform to Nuclear Regulatory Commission (NRC) and other regulatory practices, procedures and methods for licensing of nuclear power plants as embodied in the United States (U.S.) Code of Federal Regulations and other pertinent documents such as Regulatory Guide 1.203, “Transient and Accident Analysis Methods” and NUREG-0800, “NRC Standard Review Plan”. In addition, the Standard should be consistent with applicable sections of ASME NQA-1-2008 “Quality Assurance Requirements for Nuclear Facility Applications (QA)”. This paper describes the general

Safety Standard for Oxygen and Oxygen Systems: Guidelines for Oxygen System Design, Materials Selection, Operations, Storage, and Transportation

Science.gov (United States)

1996-01-01

NASA's standard for oxygen system design, materials selection, operation, and transportation is presented. Minimum guidelines applicable to NASA Headquarters and all NASA Field Installations are contained.

The evolution of IRRR nuclear standards from the single failure criterion and their impact on system design

International Nuclear Information System (INIS)

Clark, D.H.

1978-01-01

One of the first industry standards developed in the United States to meet regulatory agency criteria for the design and installation of nuclear power plant control and instrumentation systems was prepared by the Institute of Electrical and Electronics Engineers, Inc., abbreviated IEEE. This was IEEE Std. 279, first issued in 1968. It was subsequently revised and reissued as IEEE Std. 279-1971 ''IEEE Standard: Criteria for Protection Systems for Nuclear Power Generating Stations''. Not only has the implementation of this standard had a tremendous impact on nuclear power plant design in the United States, it has been the base document from which subsequent IEEE nuclear standards have been developed. Three major concepts which are addressed by IEEE 279, and which have had a major impact upon control and instrumentation systems in nuclear power plants are the following : 1) Single failure criterion. 2) Equipment qualification. 3) Channel independence. Each of these concepts has resulted in the development of subsequent IEEE Nuclear Standards. The impact of some of these on control and instrumentation systems are discussed. (author)

NASA Space Flight Human-System Standard Human Factors, Habitability, and Environmental Health

Science.gov (United States)

Holubec, Keith; Connolly, Janis

2010-01-01

This slide presentation reviews the history, and development of NASA-STD-3001, NASA Space Flight Human-System Standard Human Factors, Habitability, and Environmental Health, and the related Human Integration Design Handbook. Currently being developed from NASA-STD-3000, this project standard currently in review will be available in two volumes, (i.e., Volume 1 -- VCrew Health and Volume 2 -- Human Factors, Habitability, and Environmental Health) and the handbook will be both available as a pdf file and as a interactive website.

Standard compliant communication of motion data in a telemonitoring system

Directory of Open Access Journals (Sweden)

Piro, Neltje Emma

2015-06-01

Full Text Available Interoperability is regarded as one of the key factors for the high acceptance of a telemonitoring system. In a general telemonitoring scenario for motion tracking, data recorded by inertial sensors should be sent from the patient's home to a central server for medical assessment by a physician. The objective of this work is to elaborate a concept on how continuously measured motion data can be transferred according to the guidelines of the and, and which adaptations are reasonable to achieve high efficiency.For the communication between sensor systems and a smartphone, the X73 standards family was applied. To cover the interface between the smartphone and a central information system, the proposed Version 2.6 was used as message exchange format. Because we are dealing with continually measured data, the HL7 message construction is oriented towards the . Two variants of the transmission of binary motion data with an HL7 message were implemented. An evaluation with regard to relevant criteria led to the decision to use REST-based web services for message transport instead of the SOAP-based variant proposed by the Continua Design Guidelines.To summarize, the developed approach uses extended standards for the transmission of motion data. The detailed results can support other work groups with comparable implementation needs. In order to achieve a fully interoperable system, the communication of motion data should be included in the guidelines of IHE and Continua Health Alliance, since motion sensors can be used in various monitoring scenarios such as in patients with multiple sclerosis or for rehabilitation in general.

General conditions for the existence of non-standard Lagrangians for dissipative dynamical systems

International Nuclear Information System (INIS)

Musielak, Z.E.

2009-01-01

Equations of motion describing dissipative dynamical systems with coefficients varying either in time or in space are considered. To identify the equations that admit a Lagrangian description, two classes of non-standard Lagrangians are introduced and general conditions required for the existence of these Lagrangians are determined. The conditions are used to obtain some non-standard Lagrangians and derive equations of motion resulting from these Lagrangians.

Integration of Standardized Management Systems: A Dilemma?

Directory of Open Access Journals (Sweden)

Manuel Ferreira Rebelo

2015-06-01

Full Text Available The growing proliferation of management systems standards (MSSs, and their individualized implementation, is a real problem faced by organizations. On the other hand, MSSs are aimed at improving efficiency and effectiveness of organizational responses in order to satisfy the requirements, needs and expectations of the stakeholders. Each organization has its own identity and this is an issue that cannot be neglected; hence, two possible approaches can be attended. First, continue with the implementation of individualized management systems (MSs; or, integrate the several MSSs versus related MSs into an integrated management system (IMS. Therefore, in this context, organizations are faced with a dilemma, as a result of the increasing proliferation and diversity of MSSs. This paper takes into account the knowledge gained through a case study conducted in the context of a Portuguese company and unveils some of the advantages and disadvantages of integration. A methodology is also proposed and presented to support organizations in developing and structuring the integration process of their individualized MSs, and consequently minimize problems that are generators of inefficiencies, value destruction and loss of competitiveness. The obtained results provide relevant information that can support Top Management decision in solving that dilemma and consequently promote a successful integration, including a better control of business risks associated to MSSs requirements and enhancing sustainable performance, considering the context in which organizations operate.

Safety critical systems handbook a straightforward guide to functional safety : IEC 61508 (2010 edition) and related standards

CERN Document Server

Smith, David J

2010-01-01

Electrical, electronic and programmable electronic systems increasingly carry out safety functions to guard workers and the public against injury or death and the environment against pollution. The international functional safety standard IEC 61508 was revised in 2010, and this is the first comprehensive guide available to the revised standard. As functional safety is applicable to many industries, this book will have a wide readership beyond the chemical and process sector, including oil and gas, power generation, nuclear, aircraft, and automotive industries, plus project, instrumentation, design, and control engineers. * The only comprehensive guide to IEC 61508, updated to cover the 2010 amendments, that will ensure engineers are compliant with the latest process safety systems design and operation standards* Helps readers understand the process required to apply safety critical systems standards* Real-world approach helps users to interpret the standard, with case studies and best practice design examples...

Development of a coincidence system for radio-nuclide standardization using surface barrier detectors

International Nuclear Information System (INIS)

Koskinas, M.F.

1988-01-01

A system for the standardization of alpha-gamma or electron-X radionuclide emitters has been developed in the present work. The system consists of one or two surface barrier detectors for alpha or electron detection which are coupled to thin-window NaI (T1) crystals suitable for low energy X or gamma ray detection. The performance of the system has been verified by means of the standardization of 241 Am, 137 Cs and 109 Cd solutions. The activity has been obtained using the extrapolation method applied to the 4Πα-γ and 2Πe c -X coincidence technique. The surface barrier detection efficiency was varied by placing absorbers over the radioactive sources or by changing the source to detector distance. The results were compared to those obtained using conventional absolute systems based on gas-flow and pressurized 4Π proportional counters, or using radioactive solutions standardized in international comparisons spondored by the Bureau International des Poids et Mesures. The expect and measured activities agree within the experimental uncertainties which were: 0.2 % for 241 Am, 0.7% for 137 Cs and 0.6% for 109 Cd. The ratio between the probabilities of (electron capture + internal conversion) and internal conversion for the K-shell of 109 Cd has been determined. The result is: 2.8883 ± 0.016. (author) [pt

Property, Plant and Equipment disclosure requirements and firm characteristics: the Portuguese Accounting Standardization System

OpenAIRE

Botelho, Rafaela; Azevedo, Graça; Costa, Alberto J.; Oliveira, Jonas

2015-01-01

In the new Portuguese accounting frame of reference (Portuguese Accounting Standardization System – Sistema de Normalização Contabilística), the issues related to Property, Plant and Equipment assets are dealt with in the Accounting and Financial Reporting Standard (Norma Contabilística de Relato Financeiro – NCRF) 7 (Property, Plant & Equipment). The present study intends to assess the degree of compliance with the disclosure requirements of this accounting standard by Portuguese unlisted co...

Standard guide for mechanical drive systems for remote operation in hot cell facilities

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 Intent: 1.1.1 The intent of this standard is to provide general guidelines for the design, selection, quality assurance, installation, operation, and maintenance of mechanical drive systems used in remote hot cell environments. The term mechanical drive systems used herein, encompasses all individual components used for imparting motion to equipment systems, subsystems, assemblies, and other components. It also includes complete positioning systems and individual units that provide motive power and any position indicators necessary to monitor the motion. 1.2 Applicability: 1.2.1 This standard is intended to be applicable to equipment used under one or more of the following conditions: 1.2.1.1 The materials handled or processed constitute a significant radiation hazard to man or to the environment. 1.2.1.2 The equipment will generally be used over a long-term life cycle (for example, in excess of two years), but equipment intended for use over a shorter life cycle is not excluded. 1.2.1.3 The ...

An application of the IAEA GCS-R-3 Standard in Nuclear Quality Management System

Energy Technology Data Exchange (ETDEWEB)

Kim, D. I.; Juhn, P. E. [TUEV SUED Korea, Seoul (Korea, Republic of); Kwon, M. J. [TUEV SUED KOCEN, Seoul (Korea, Republic of)

2012-03-15

IAEA GCS-R-3 Standard (2006) is intended to help nuclear community establishing a nuclear quality management system that integrates such 6 elements as safety, health, environment, security, quality and economics. In the present paper, the management principles of GCS-R-3 Standard are compared with those of ISO 9001 and ASME N/A-1 Codes and Standards. The paper also summarizes the worldwide survey on application of GS-R-3, which was conducted by the TUEV SUED Korea in 2011. The result concludes that the top priority should be given to safety upon which the management system must be based, in proper coordination with other 5 elements to enhance nuclear safety, in particular after Fukushima Dais-Ici nuclear power accidents on 11{sup th} March 2011 in Japan.

The design of management system guidelines and technical standards for the production of x-ray aircraft

International Nuclear Information System (INIS)

Dyah Palupi; Made Pramayuni

2013-01-01

Concept of management systems guidelines and technical standards X-ray Equipment Production arranged in order to prepare for the effective and efficient regulatory to ensure the safety of X-ray equipment production in Indonesia. The regulatory tools may the government policy or regulations. Authors proposed that BAPETEN develop guidelines for management system of x-ray equipment production by combining ISO 13485 with BAPETEN Chairman Regulation no.4 /2010. Author also suggested that BAPETEN make technical standards IEC 60601 as a mandatory standard in producing x-ray equipment. (author)

A dedicated on-line system for the preparation and validation of standard beads in XRF analysis

International Nuclear Information System (INIS)

Yamamoto, Yasuyuki; Ogasawara, Noriko; Nakata, Akio; Shoji, Shizuko.

1995-01-01

A dedicated on-line system in X-ray Fluorescence (XRF) analysis with glass-bead method was developed in which preparation of standard beads was automated including proper choice of reagents, assignment of bead compositions and validation of the prepared beads. This system features: a. Fundamental Parameter (FP) Method for validation of standard beads. b. An original database of high purity reagents for standards. c. Automatic calculation of suitable composition for each standard bead, by giving a range for each element and the number of standard beads. 1) The calculation is based on random numbers, and makes a random assignment of composition for each bead. 2) The calculation results are automatically stored in a computer as a condition file for quantitative analysis. 3) An amount of a material for a standard mixture is corrected if a valence or a chemical compound for an analysis element is different from that of the standard material in the database. In order to realize these features, many high purity reagents were examined for their purities and other characteristics to test a suitability to use for a standard material, and a software for on-line processings was originally developed. (author)

Quasiparticle-induced decoherence of microscopic two-level-systems in superconducting qubits

Energy Technology Data Exchange (ETDEWEB)

Bilmes, Alexander; Lisenfeld, Juergen; Zanker, Sebastian; Weiss, Georg; Ustinov, Alexey V. [PHI, KIT, Karlsruhe (Germany); Marthaler, Michael; Schoen, Gerd [TFP, KIT, Karlsruhe (Germany)

2016-07-01

Parasitic Two-Level-Systems (TLS) are one of the main sources of decoherence in superconducting nano-scale devices such as SQUIDs, resonators and quantum bits (qubits), although the TLS' microscopic nature remains unclear. We use a superconducting phase qubit to detect TLS contained within the tunnel barrier of the qubit's Al/AlOx/Al Josephson junction. If the TLS transition frequency lies within the 6-10 GHz range, we can coherently drive it by resonant microwave pulses and access its quantum state by utilizing the strong coupling to the qubit. Our previous measurements of TLS coherence in dependence of the temperature indicate that quasiparticles (QPs), which diffuse from the superconducting Al electrodes into the oxide layer, may give rise to TLS energy loss and dephasing. Here, we probe the TLS-QP interaction using a reliable method of in-situ QP injection via an on-chip dc-SQUID that is pulse-biased beyond its switching current. The QP density is calibrated by measuring associated characteristic changes to the qubit's energy relaxation rate. We will present experimental data which show the QP-induced TLS decoherence in good agreement to theoretical predictions.

Section for Standard and Patents - Standardization and Patents

International Nuclear Information System (INIS)

Wojtowicz, S.; Trechcinski, R.; Rybka, M.; Ryszkowska, A.; Wardaszko, J.

1997-01-01

Full text: The most important tasks of the Section in 1996 were: preparation of national standards and program of future work on standards for nuclear instrumentation and electronic equipment in nuclear engineering; organization of activities and participation in the meetings of the Commissions for Standardization No 173 Microprocessor Systems, No 266 Nuclear Instrumentation; giving opinions and expertises on national and international standards for equipment in nuclear engineering; cooperation with the Commission for Standardization No 246 Radiological Protection; control of inventiveness activity; The quality of the technical products is being improved by: a) selection of the proper types of interface systems, technical coordination and quality control; b) creation of standards at a high technical level; The Section works mainly for the Polish Committee for Standardization, the National Atomic Energy Agency, Association of Polish Electrical Engineers and Research Institutes in Poland. The activity of the Section is useful for all national institutions where backplane busses and nuclear electronic equipment is produced or used. The Section participates in the following international organizations: IEC (International Electrotechnical Commission) TC 45 (Nuclear Instrumentation); ISO/IEC Joint Technical Committee ISO/IEC JTCl SC26 (Microprocessor systems); ESONE (European Studies on Norms for Electronics); The section takes part in popularization of nuclear technology and instrumentation in the following ways: distribution of standards and technical documentation to national institutions dealing with nuclear apparatus; collecting and distributing technical information from international organizations (e.g. ESONE); organization of technical and scientific, national and international conferences (New Generation Nuclear Power Plants - September 96, QNX in Real World - January 96); participation in the technical conference organized by the Polish Committee for

25 CFR 547.12 - What are the minimum technical standards for downloading on a Class II gaming system?

Science.gov (United States)

2010-04-01

... on a Class II gaming system? 547.12 Section 547.12 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF THE INTERIOR HUMAN SERVICES MINIMUM TECHNICAL STANDARDS FOR GAMING EQUIPMENT USED WITH THE PLAY... gaming system? This section provides standards for downloading on a Class II gaming system. (a) Downloads...

C-Lock: An online system to standardize the estimation of agricultural carbon sequestration credits

Energy Technology Data Exchange (ETDEWEB)

Updegraff, Karen; Zimmerman, Patrick R.; Capehart, William J. [Institute of Atmospheric Sciences, South Dakota School of Mines and Technology, 501 E. St. Joseph Street, Rapid City, SD 57701-3995 (United States); Price, Maribeth [Department of Geology, South Dakota School of Mines and Technology, 501 E. St. Joseph Street, Rapid City, SD 57701-3995 (United States)

2005-10-15

C-Lock (patent pending) is a system that has been designed to produce standardized carbon emission reduction credits (CERCs) that minimize litigation risks to purchasers and maximize the potential value to agricultural producers. C-Lock provides a web-based user interface linking producer-supplied, verifiable, management data, a detailed regional-scale GIS, and a biogeochemical model (CENTURY). Output includes historical incremental carbon sequestration since 1990 and predictions of future sequestration, packaged to satisfy evolving regulatory standards. C-Lock incorporates a unique uncertainty analysis and a three-level verification system to produce certified CERCs for specific land parcels in a way that is reproducible, equitable, and regionally defensible. Using a South Dakota farm as an example, the authors show how, by avoiding reliance on field sampling, this system can minimize measurement and monitoring costs. It allows individual producers a high degree of control over contract design and marketing, thereby reducing transaction costs. The transparent, standardized, and auditable procedure produces CERCs of maximum value to those seeking emission offsets. (author)

Safety evaluation report related to the preliminary design of the Standard Reference System, RESAR-414

International Nuclear Information System (INIS)

1978-11-01

The safety evaluation for the Westinghouse Standard Reactor includes information on general reactor characteristics; design criteria for systems and components; reactor coolant system; engineered safety systems; instrumentation and controls; electric power systems; auxiliary systems; steam and power conversion system; radioactive waste management; radiation protection; conduct of operations; accident analyses; and quality assurance

A preliminary study on the design in architecture of nuclear and radiation safety standard system

International Nuclear Information System (INIS)

Song Dahu; Zhang Chi; Yang Lili; Li Bin; Liu Yingwei; An Hongzhen; Gao Siyi; Liu Ting; Meng De

2014-01-01

The connotation and function of nuclear and radiation safety standards are analyzed, and their relationships with the relevant laws and regulations are discussed in the paper. Some suggestions and blue print of overall architecture to build nuclear and radiation safety standard system are proposed, on the basis of researching the application status quo, existing problems and needs for nuclear and radiation safety standards in China. This work is a beneficial exploration and attempt to establish China's nuclear and radiation safety standards. (authors)

Standard practices for verification of displacement measuring systems and devices used in material testing machines

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 These practices cover procedures and requirements for the calibration and verification of displacement measuring systems by means of standard calibration devices for static and quasi-static testing machines. This practice is not intended to be complete purchase specifications for testing machines or displacement measuring systems. Displacement measuring systems are not intended to be used for the determination of strain. See Practice E83. 1.2 These procedures apply to the verification of the displacement measuring systems associated with the testing machine, such as a scale, dial, marked or unmarked recorder chart, digital display, etc. In all cases the buyer/owner/user must designate the displacement-measuring system(s) to be verified. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems m...

MATE standardization

Science.gov (United States)

Farmer, R. E.

1982-11-01

The MATE (Modular Automatic Test Equipment) program was developed to combat the proliferation of unique, expensive ATE within the Air Force. MATE incorporates a standard management approach and a standard architecture designed to implement a cradle-to-grave approach to the acquisition of ATE and to significantly reduce the life cycle cost of weapons systems support. These standards are detailed in the MATE Guides. The MATE Guides assist both the Air Force and Industry in implementing the MATE concept, and provide the necessary tools and guidance required for successful acquisition of ATE. The guides also provide the necessary specifications for industry to build MATE-qualifiable equipment. The MATE architecture provides standards for all key interfaces of an ATE system. The MATE approach to the acquisition and management of ATE has been jointly endorsed by the commanders of Air Force Systems Command and Air Force Logistics Command as the way of doing business in the future.

Computer system validation: an overview of official requirements and standards.

Science.gov (United States)

Hoffmann, A; Kähny-Simonius, J; Plattner, M; Schmidli-Vckovski, V; Kronseder, C

1998-02-01

A brief overview of the relevant documents for companies in the pharmaceutical industry, which are to be taken into consideration to fulfil computer system validation requirements, is presented. We concentrate on official requirements and valid standards in the USA, European Community and Switzerland. There are basically three GMP-guidelines. their interpretations by the associations of interests like APV and PDA as well as the GAMP Suppliers Guide. However, the three GMP-guidelines imply the same philosophy about computer system validation. They describe more a what-to-do approach for validation, whereas the GAMP Suppliers Guide describes a how-to-do validation. Nevertheless, they do not contain major discrepancies.

Standards and quality

CERN Document Server

El-Tawil, Anwar

2015-01-01

The book brings together a number of subjects of prime importance for any practicing engineer and, students of engineering. The book explains the concepts and functions of voluntary standards, mandatory technical regulations, conformity assessment (testing and measurement of products), certification, quality and quality management systems as well as other management systems such as environmental, social responsibility and food safety management systems.The book also gives a comprehensive description of the role of metrology systems that underpin conformity assessment. A description is given of typical national systems of standards, quality and metrology and how they relate directly or through regional structures to international systems. The book also covers the relation between standards and trade and explains the context and stipulations of the Technical Barriers to Trade Agreement of the World Trade Organization (WTO).

Comparison of the Standards applied to Instrumentation and Control Systems for Nuclear Power Stations in Korea and Russia

International Nuclear Information System (INIS)

Park, Joo Hyun; Hwang, In Koo; Lee, Dong Young

2005-04-01

This report describes a comparison result of technical standards applied to instrumentation and control systems for nuclear power plants between in Korea and in Russia. Russia also has a state-run organization authorized to conduct approval, cancellation, and audit in use of nuclear facility or equipment. The Russian standards for nuclear instrumentation and control equipment are analogous with the Korean ones in the aspect of basic concepts and principles. However, there are some differences in document structure, design requirements, qualification test items, depth of contents between two standard systems. The biggest deviation exists in the standard documents for seismic qualification and electromagnetic interference qualification. Korean seismic qualification standard utilizing US approach, defines testing and qualification methods specifically and clearly. Russian standards however provide only conceptual definitions and requirements in the seismic related aspects. Therefore, it is conceived that any equipment or system qualified seismically in accordance with Korean standards should additionally provide technical evidence that it is satisfactory with Russian standards as well. In electromagnetic interference qualification, because Russian standard requires more testing items than the current Korean standard, the additional qualification tests are necessary to meet the Russian requirements. However, these additional test items are based on IEC(International Electrotechnical Commission), therefore it is not a problem to perform those tests in a Korean testing facility

Comparison of the Standards applied to Instrumentation and Control Systems for Nuclear Power Stations in Korea and Russia

Energy Technology Data Exchange (ETDEWEB)

Park, Joo Hyun; Hwang, In Koo; Lee, Dong Young

2005-04-15

This report describes a comparison result of technical standards applied to instrumentation and control systems for nuclear power plants between in Korea and in Russia. Russia also has a state-run organization authorized to conduct approval, cancellation, and audit in use of nuclear facility or equipment. The Russian standards for nuclear instrumentation and control equipment are analogous with the Korean ones in the aspect of basic concepts and principles. However, there are some differences in document structure, design requirements, qualification test items, depth of contents between two standard systems. The biggest deviation exists in the standard documents for seismic qualification and electromagnetic interference qualification. Korean seismic qualification standard utilizing US approach, defines testing and qualification methods specifically and clearly. Russian standards however provide only conceptual definitions and requirements in the seismic related aspects. Therefore, it is conceived that any equipment or system qualified seismically in accordance with Korean standards should additionally provide technical evidence that it is satisfactory with Russian standards as well. In electromagnetic interference qualification, because Russian standard requires more testing items than the current Korean standard, the additional qualification tests are necessary to meet the Russian requirements. However, these additional test items are based on IEC(International Electrotechnical Commission), therefore it is not a problem to perform those tests in a Korean testing facility.

76 FR 42534 - Mandatory Reliability Standards for Interconnection Reliability Operating Limits; System...

Science.gov (United States)

2011-07-19

... Reliability Operating Limits; System Restoration Reliability Standards AGENCY: Federal Energy Regulatory... data necessary to analyze and monitor Interconnection Reliability Operating Limits (IROL) within its... Interconnection Reliability Operating Limits, Order No. 748, 134 FERC ] 61,213 (2011). \\2\\ The term ``Wide-Area...

78 FR 2443 - Criminal Justice Interview Room Recording System (IRRS) Standard, Supplier's Declaration of...

Science.gov (United States)

2013-01-11

... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (NIJ) Docket No. 1612] Criminal Justice Interview Room Recording System (IRRS) Standard, Supplier's Declaration of Conformity Requirements, and... three draft documents related to Interview Room Recording Systems (IRRS) used by criminal justice...

Electronic health record standards, coding systems, frameworks, and infrastructures

CERN Document Server

Sinha, Pradeep K; Bendale, Prashant; Mantri, Manisha; Dande, Atreya

2013-01-01

Discover How Electronic Health Records Are Built to Drive the Next Generation of Healthcare Delivery The increased role of IT in the healthcare sector has led to the coining of a new phrase ""health informatics,"" which deals with the use of IT for better healthcare services. Health informatics applications often involve maintaining the health records of individuals, in digital form, which is referred to as an Electronic Health Record (EHR). Building and implementing an EHR infrastructure requires an understanding of healthcare standards, coding systems, and frameworks. This book provides an

Electronic circuits, systems and standards the best of EDN

CERN Document Server

Hickman, Ian

2013-01-01

Electronic Circuits, Systems and Standards: The Best of EDN is a collection of 66 EDN articles. The topics covered in this collection are diverse but all are relevant to controlled circulation electronics. The coverage of the text includes topics about software and algorithms, such as simple random number algorithm; simple log algorithm; and efficient algorithm for repeated FFTs. The book also tackles measurement related topics, including test for identifying a Gaussian noise source; enhancing product reliability; and amplitude-locked loop speeds filter test. The text will be useful to student

Timely diagnosis of dairy calf respiratory disease using a standardized scoring system.

Science.gov (United States)

McGuirk, Sheila M; Peek, Simon F

2014-12-01

Respiratory disease of young dairy calves is a significant cause of morbidity, mortality, economic loss, and animal welfare concern but there is no gold standard diagnostic test for antemortem diagnosis. Clinical signs typically used to make a diagnosis of respiratory disease of calves are fever, cough, ocular or nasal discharge, abnormal breathing, and auscultation of abnormal lung sounds. Unfortunately, routine screening of calves for respiratory disease on the farm is rarely performed and until more comprehensive, practical and affordable respiratory disease-screening tools such as accelerometers, pedometers, appetite monitors, feed consumption detection systems, remote temperature recording devices, radiant heat detectors, electronic stethoscopes, and thoracic ultrasound are validated, timely diagnosis of respiratory disease can be facilitated using a standardized scoring system. We have developed a scoring system that attributes severity scores to each of four clinical parameters; rectal temperature, cough, nasal discharge, ocular discharge or ear position. A total respiratory score of five points or higher (provided that at least two abnormal parameters are observed) can be used to distinguish affected from unaffected calves. This can be applied as a screening tool twice-weekly to identify pre-weaned calves with respiratory disease thereby facilitating early detection. Coupled with effective treatment protocols, this scoring system will reduce post-weaning pneumonia, chronic pneumonia, and otitis media.

Standard-target calibration of an acoustic backscatter system

Science.gov (United States)

Foote, Kenneth G.; Martini, Marinna A.

2010-01-01

The standard-target method used to calibrate scientific echo sounders and other scientific sonars by a single, solid elastic sphere is being adapted to acoustic backscatter (ABS) systems. Its first application, to the AQUAscat 1000, is described. The on-axis sensitivity and directional properties of transducer beams at three operating frequencies, nominally 1, 2.5, and 4 MHz, have been determined using a 10-mm-diameter sphere of tungsten carbide with 6% cobalt binder. Preliminary results are reported for the 1-MHz transducer. Their application to measurements of suspended sediment made in situ with the same device is described. This will enable the data to be expressed directly in physical units of volume backscattering.

Robust Road Condition Detection System Using In-Vehicle Standard Sensors

Directory of Open Access Journals (Sweden)

Juan Jesús Castillo Aguilar

2015-12-01

Full Text Available The appearance of active safety systems, such as Anti-lock Braking System, Traction Control System, Stability Control System, etc., represents a major evolution in road safety. In the automotive sector, the term vehicle active safety systems refers to those whose goal is to help avoid a crash or to reduce the risk of having an accident. These systems safeguard us, being in continuous evolution and incorporating new capabilities continuously. In order for these systems and vehicles to work adequately, they need to know some fundamental information: the road condition on which the vehicle is circulating. This early road detection is intended to allow vehicle control systems to act faster and more suitably, thus obtaining a substantial advantage. In this work, we try to detect the road condition the vehicle is being driven on, using the standard sensors installed in commercial vehicles. Vehicle models were programmed in on-board systems to perform real-time estimations of the forces of contact between the wheel and road and the speed of the vehicle. Subsequently, a fuzzy logic block is used to obtain an index representing the road condition. Finally, an artificial neural network was used to provide the optimal slip for each surface. Simulations and experiments verified the proposed method.

Robust Road Condition Detection System Using In-Vehicle Standard Sensors.

Science.gov (United States)

Castillo Aguilar, Juan Jesús; Cabrera Carrillo, Juan Antonio; Guerra Fernández, Antonio Jesús; Carabias Acosta, Enrique

2015-12-19

The appearance of active safety systems, such as Anti-lock Braking System, Traction Control System, Stability Control System, etc., represents a major evolution in road safety. In the automotive sector, the term vehicle active safety systems refers to those whose goal is to help avoid a crash or to reduce the risk of having an accident. These systems safeguard us, being in continuous evolution and incorporating new capabilities continuously. In order for these systems and vehicles to work adequately, they need to know some fundamental information: the road condition on which the vehicle is circulating. This early road detection is intended to allow vehicle control systems to act faster and more suitably, thus obtaining a substantial advantage. In this work, we try to detect the road condition the vehicle is being driven on, using the standard sensors installed in commercial vehicles. Vehicle models were programmed in on-board systems to perform real-time estimations of the forces of contact between the wheel and road and the speed of the vehicle. Subsequently, a fuzzy logic block is used to obtain an index representing the road condition. Finally, an artificial neural network was used to provide the optimal slip for each surface. Simulations and experiments verified the proposed method.

Optimal synthesis and operation of advanced energy supply systems for standard and domotic home

International Nuclear Information System (INIS)

Buoro, Dario; Casisi, Melchiorre; Pinamonti, Piero; Reini, Mauro

2012-01-01

Highlights: ► Definition of an optimization model for a home energy supply system. ► Optimization of the energy supply system for standard and domotic home. ► Strong improvement can be achieved adopting the optimal system in standard and domotic home. ► The improvements are consistent if supply side and demand side strategies are applied together. ► Solutions with internal combustion engines are less sensible to market price of electricity and gas. - Abstract: The paper deals with the optimization of an advanced energy supply systems for two dwellings: a standard home and an advanced domotic home, where some demand side energy saving strategies have been implemented. In both cases the optimal synthesis, design and operation of the whole energy supply system have been obtained and a sensitivity analysis has been performed, by introducing different economic constraints. The optimization model is based on a Mixed Integer Linear Program (MILP) and includes different kinds of small-scale cogenerators, geothermal heat pumps, boilers, heat storages, solar thermal and photovoltaic panels. In addition, absorption machines, supplied with cogenerated heat, can be used instead of conventional electrical chiller to face the cooling demand. The aim of the analysis is to address the question if advanced demand strategies and supply strategies have to be regarded as alternatives, or if they have to be simultaneously applied, in order to obtain the maximum energy and economic benefit.

Standardized Semantic Markup for Reference Terminologies, Thesauri and Coding Systems: Benefits for distributed E-Health Applications.

Science.gov (United States)

Hoelzer, Simon; Schweiger, Ralf K; Liu, Raymond; Rudolf, Dirk; Rieger, Joerg; Dudeck, Joachim

2005-01-01

With the introduction of the ICD-10 as the standard for diagnosis, the development of an electronic representation of its complete content, inherent semantics and coding rules is necessary. Our concept refers to current efforts of the CEN/TC 251 to establish a European standard for hierarchical classification systems in healthcare. We have developed an electronic representation of the ICD-10 with the extensible Markup Language (XML) that facilitates the integration in current information systems or coding software taking into account different languages and versions. In this context, XML offers a complete framework of related technologies and standard tools for processing that helps to develop interoperable applications.

Design analysis and comparison between standard and rotary porting systems for IC engine

Energy Technology Data Exchange (ETDEWEB)

Palmisano, R.; Ng, H.D. [Concordia Univ., Montreal, PQ (Canada). Dept. of Mechanical and Industrial Engineering

2009-07-01

A method of improving the efficiency of an internal combustion engine was presented. The proposed design used a new sealing technology to optimize a rotary valve design. The design was compared with standard poppet porting system using a computer aided engineering (CAE) method. A double port cylinder configuration was used in order to allow continuous flow into the chamber and minimize the exposed surface area in the combustion chamber. The design also minimized distortion on the component when exposed to high condensation pressures. A transfer case was used to allow for easy adaptation of the configuration to a multi-cylinder engine. A mechanism dynamics extension (MDO) program was used to conduct dynamic analyses on the rotary and standard valve porting systems. The study showed that the poppet system required 62 times more torque than the new rotary valve design. It was concluded that further research is needed to examine the flow properties of both designs. 2 refs., 6 figs.

An adaptive software defined radio design based on a standard space telecommunication radio system API

Science.gov (United States)

Xiong, Wenhao; Tian, Xin; Chen, Genshe; Pham, Khanh; Blasch, Erik

2017-05-01

Software defined radio (SDR) has become a popular tool for the implementation and testing for communications performance. The advantage of the SDR approach includes: a re-configurable design, adaptive response to changing conditions, efficient development, and highly versatile implementation. In order to understand the benefits of SDR, the space telecommunication radio system (STRS) was proposed by NASA Glenn research center (GRC) along with the standard application program interface (API) structure. Each component of the system uses a well-defined API to communicate with other components. The benefit of standard API is to relax the platform limitation of each component for addition options. For example, the waveform generating process can support a field programmable gate array (FPGA), personal computer (PC), or an embedded system. As long as the API defines the requirements, the generated waveform selection will work with the complete system. In this paper, we demonstrate the design and development of adaptive SDR following the STRS and standard API protocol. We introduce step by step the SDR testbed system including the controlling graphic user interface (GUI), database, GNU radio hardware control, and universal software radio peripheral (USRP) tranceiving front end. In addition, a performance evaluation in shown on the effectiveness of the SDR approach for space telecommunication.

Perceptions About The ISO 9000 Quality System Standard Revision And Its Value: The Dutch Experience

NARCIS (Netherlands)

A. van der Wiele (Ton); J.D. van Iwaarden (Jos); A.R.T. Williams (Roger); B.G. Dale (Barry)

2004-01-01

textabstractThe aim of the research reported in this paper is to assess the relative value of the 2000 version of the ISO 9000 series of quality management system standards in comparison to the 1994 version. 773 organisations in the Netherlands which have all been certified to the ISO 9000 standard

Improvement of security techniques and protection of biometric data in biometric systems: Presentation of International Standard ISO 24745

OpenAIRE

Milinković, Milorad

2017-01-01

This paper presents the International Standard ISO 24745 as a potential security tool for biometric information protection, more precisely as a tool for privacy protection in biometric systems. This is one of the latest internationally accepted standards that address the security issues of biometric systems.

Update of the list of QPS‐recommended biological agents intentionally added to food or feed as notified to EFSA 6: suitability of taxonomic units notified to EFSA until March 2017

NARCIS (Netherlands)

Ricci, Antonia; Allende, Ana; Bolton, Declan; Chemaly, Marianne; Davies, Robert; Girones, Rosina; Koutsoumanis, Kostas; Lindqvist, Roland; Nørrung, Birgit; Robertson, Lucy; Ru, Giuseppe; Fernandez Escamez, Pablo Salvador; Sanaa, Moez; Simmons, Marion; Skandamis, Panagiotis; Snary, Emma; Speybroeck, Niko; Kuile, Ter Benno; Threlfall, John; Wahlström, Helene; Cocconcelli, Pier Sandro; Peixe, Luisa; Maradona, Miguel Prieto; Querol, Amparo; Suarez, Juan Evaristo; Sundh, Ingvar; Vlak, Just; Correia, Sandra; Herman, Lieve

2017-01-01

The qualified presumption of safety (QPS) concept was developed to provide a harmonised generic pre-evaluation to support safety risk assessments of biological agents performed by EFSA's scientific Panels. The identity, body of knowledge, safety concerns and antimicrobial resistance of valid

Standards for electronic imaging for graphic arts systems

Science.gov (United States)

Dunn, S. T.; Dunn, Patrice M.

1991-03-01

This paper examines the development of electronic imaging standards by and for the graphic arts industry. Taken collectively this body of work is referred to as Digital Data Exchange Standards (DDES). Because these standards are being driven by market and user requirements there are several fundamental guiding principles to their development. This paper examines these and provides an overview to the technical developments undertaken by the accredited graphic arts industry standards committees to date.

Loop system for creating jet fuel vapor standards used in the calibration of infrared spectrophotometers and gas chromatographs.

Science.gov (United States)

Reboulet, James; Cunningham, Robert; Gunasekar, Palur G; Chapman, Gail D; Stevens, Sean C

2009-02-01

A whole body inhalation study of mixed jet fuel vapor and its aerosol necessitated the development of a method for preparing vapor only standards from the neat fuel. Jet fuel is a complex mixture of components which partitions between aerosol and vapor when aspirated based on relative volatility of the individual compounds. A method was desired which could separate the vapor portion from the aerosol component to prepare standards for the calibration of infrared spectrophotometers and a head space gas chromatography system. A re-circulating loop system was developed which provided vapor only standards whose composition matched those seen in an exposure system. Comparisons of nominal concentrations in the exposure system to those determined by infrared spectrophotometry were in 92-95% agreement. Comparison of jet fuel vapor concentrations determined by infrared spectrophotometry compared to head space gas chromatography yielded a 93% overall agreement in trial runs. These levels of agreement show the loop system to be a viable method for creating jet fuel vapor standards for calibrating instruments.

75 FR 78269 - Vehicular Digital Multimedia Evidence Recording System (VDMERS) Standard for Law Enforcement

Science.gov (United States)

2010-12-15

...In an effort to obtain comments from interested parties, the U.S. Department of Justice, Office of Justice Programs, National Institute of Justice (NIJ) will make available to the general public the draft ``Vehicular Digital Multimedia Evidence Recording System Standard for Law Enforcement.'' The opportunity to provide comments on this voluntary standard is open to industry technical representatives, law enforcement agencies and organizations, research, development and scientific communities, and all other stakeholders and interested parties. Those individuals wishing to obtain and provide comments on the draft standard under consideration are directed to the following Web site: http://www.justnet.org.

A 15 channel 2- and 3-fold coincidence counting system for radioactivity standardization

International Nuclear Information System (INIS)

Simpson, B.R.S.; Meyer, B.R.; Raave, D.A.

1986-01-01

The 4π β-γ liquid scintillation coincidence counting system which is used at the National Accelerator Centre for standardizing radioisotopes, has been extended to allow for up to fifteen data points to be measured simultaneously by introducing a 15-fold coincidence unit and a 32-channel scaler into the system. A new control / data acquisition computer program has been written and its operation explained in detail. The advantages of the new system are discussed, and the activity of a 139 Ce source as measured by the new system and the old 3-fold system is compared

Breast calcifications. A standardized mammographic reporting and data system to improve positive predictive value

International Nuclear Information System (INIS)

Perugini, G.; Bonzanini, B.; Valentino, C.

1999-01-01

The purpose of this work is to investigate the usefulness of a standardized reporting and data system in improving the positive predictive value of mammography in breast calcifications. Using the Breast Imaging Reporting and Data System lexicon developed by the American College of Radiology, it is defined 5 descriptive categories of breast calcifications and classified diagnostic suspicion of malignancy on a 3-grade scale (low, intermediate and high). Two radiologists reviewed 117 mammographic studies selected from those of the patients submitted to surgical biopsy for mammographically detected calcifications from January 1993 to December 1997, and classified them according to the above criteria. The positive predictive value was calculated for all examinations and for the stratified groups. Defining a standardized system for assessing and describing breast calcifications helps improve the diagnostic accuracy of mammography in clinical practice [it

49 CFR 571.118 - Standard No. 118; Power-operated window, partition, and roof panel systems.

Science.gov (United States)

2010-10-01

...-operated window, partition, and roof panel systems. S1. Purpose and scope. This standard specifies requirements for power operated window, partition, and roof panel systems to minimize the likelihood of death... Figure 2. Power operated roof panel systems mean moveable panels in the vehicle roof which close by...

Hydrogenic systems for calculable frequency standards. Status and options

International Nuclear Information System (INIS)

Flowers, J.; Klein, H.; Knight, D.

2001-01-01

The study of hydrogen and hydrogenic (one-electron) ions is an area of rapid progress and one of great potential for future frequency standards. In 1997, the two-photon 1S-2S transition in the hydrogen atom was included in the list of approved radiations for the practical realisation of the metre, and since then revolutions in optical frequency metrology have reduced the uncertainty in its frequency by more than an order of magnitude, to 1.8 parts in 10 14 . Hydrogenic systems are simple enough that the frequencies of their transitions can be calculated in terms of the Rydberg constant with an accuracy that can approach or exceed the measurement uncertainty. Transitions in such systems can be thought of as forming a natural frequency scale, and offer the prospect of a set of quantum frequency standards which are directly related to the fundamental constants. The Rydberg constant is currently best determined from optical frequency measurements in hydrogen. However, to take full advantage of the recent high accuracy 1S-2S frequency measurement requires: Improved measurements of other transition frequencies in the hydrogen atom; Reduced uncertainty in the quantum electrodynamic (QED) contributions to the energy levels, in particular the two-loop binding corrections; An improved value for the proton charge radius. In He + and one-electron systems of higher atomic number Z, the two-loop binding corrections are a fractionally larger part of the Lamb shift due to their rapid scaling with Z. Measurements of the Lamb shift in medium-Z hydrogenic ions can therefore provide tests of these corrections, and feed in to the theoretical understanding of hydrogen itself Although both theory and experiment are less accurate at higher Z, there is the potential for a new range of X-ray standards, providing that the QED corrections are well understood and new absolute measurement techniques can be developed. A number of areas are suggested for future investigation: Improving the

National Incident Management System (NIMS) Standards Review Panel Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

Stenner, Robert D.; Kirk, Jennifer L.; Stanton, James R.; Shebell, Peter; Schwartz, Deborah S.; Judd, Kathleen S.; Gelston, Gariann M.

2006-02-07

The importance and need for full compliant implementation of NIMS nationwide was clearly demonstrated during the Hurricane Katrina event, which was clearly expressed in Secretary Chertoff's October 4, 2005 letter addressed to the State's governors. It states, ''Hurricane Katrina was a stark reminder of how critical it is for our nation to approach incident management in a coordinated, consistent, and efficient manner. We must be able to come together, at all levels of government, to prevent, prepare for, respond to, and recover from any emergency or disaster. Our operations must be seamless and based on common incident management doctrine, because the challenges we face as a nation are far greater than capabilities of any one jurisdiction.'' The NIMS is a system/architecture for organizing response on a ''national'' level. It incorporations ICS as a main component of that structure (i.e., it institutionalizes ICS in NIMS). In a paper published on the NIMS Website, the following statements were made: ''NIMS represents a core set of doctrine, principles, terminology, and organizational processes to enable effective, efficient and collaborative incident management at all levels. To provide the framework for interoperability and compatibility, the NIMS is based on a balance between flexibility and standardization.'' Thus the NIC is challenged with the need to adopt quality SDO generated standards to support NIMS compliance, but in doing so maintain the flexibility necessary so that response operations can be tailored for the specific jurisdictional and geographical needs across the nation. In support of this large and complex challenge facing the NIC, the Pacific Northwest National Laboratory (PNNL) was asked to provide technical support to the NIC, through their DHS Science and Technology ? Standards Portfolio Contract, to help identify, review, and develop key standards for NIMS compliance. Upon

Automated system for calculating the uncertainty of standards

International Nuclear Information System (INIS)

Harvel, C.D.

1990-01-01

Working Calibration and Test Material (WCTM) solutions are essential as standards in the surveillance of analytical methods, the calibration of equipment and methods, and the training and testing of laboratory personnel. Before the WCTM can be used it must be characterized. That is, the WCTM concentration and its associated uncertainty must be estimated. The characterization of a WCTM is a tedious process. The chemistry and subsequent statistical analysis require a significant amount of care. For a nonstatistician, the statistical analysis of a WCTM characterization can be quite difficult. In addition, the WCTM traceability and characterization must be thoroughly documented as required by DOE Order 5633.3 [1]. An automated system can easily do the statistical analysis and provide the necessary documentation. 3 refs., 2 figs

Commentary on CSA Standard Z662-99, oil and gas pipeline systems : Special Publication Z622.1-01

Energy Technology Data Exchange (ETDEWEB)

Kalra, S; Burford, G; Adragna, M; Coyle, S; Hawryn, S; Martin, A; McConnell, J [eds.; Kumaralagan, I; Hassan, H

2001-04-01

CSA Standard Z662 presents the requirements for oil and gas pipeline systems and describes what has been accepted as good safety practice. This special publication is not part of the Standard and has not been formally reviewed by the Technical Committee responsible for the Standard, therefore it does not provide formal interpretations of the Standard. This special publication should be considered as an informal annotation of portions of the Standard. This paper presents background information regarding certain clauses and requirements in the Standard. Revisions to this first edition of CSA Special Publication Z662.1 are likely to be made whenever new information needs to be released. This publication discussed some of the standards for oil and gas pipelines in terms of design, materials, installation, joining, pressure testing, corrosion control, as well as operation, maintenance and upgrading. The report also referred to offshore gas and oil distribution systems including steel, plastic and aluminum piping. refs., figs.

Risk in Management Systems according to ISO standard

Directory of Open Access Journals (Sweden)

P. Królas

2010-07-01

Full Text Available The purpose of this article was to present selected management standards in context of risk management. It presents main ISOmanagement standards (ISO 9001, ISO 14001, OHSAS 18001, ISO 27001, BS 25999, ISO 31000 that apply to polish enterprises. In thefirst part of this article there are analyzed management standards regarding quality, environment, occupational health and safety,information security, as well as business continuity management and risk management. The second part of the article discusses the processof dealing with risk based on chosen management standard.