Smart modeling and simulation for complex systems practice and theory

CERN Document Server

Ren, Fenghui; Zhang, Minjie; Ito, Takayuki; Tang, Xijin

2015-01-01

This book aims to provide a description of these new Artificial Intelligence technologies and approaches to the modeling and simulation of complex systems, as well as an overview of the latest scientific efforts in this field such as the platforms and/or the software tools for smart modeling and simulating complex systems. These tasks are difficult to accomplish using traditional computational approaches due to the complex relationships of components and distributed features of resources, as well as the dynamic work environments. In order to effectively model the complex systems, intelligent technologies such as multi-agent systems and smart grids are employed to model and simulate the complex systems in the areas of ecosystem, social and economic organization, web-based grid service, transportation systems, power systems and evacuation systems.

Evaluation of articulation simulation system using artificial maxillectomy models.

Science.gov (United States)

Elbashti, M E; Hattori, M; Sumita, Y I; Taniguchi, H

2015-09-01

Acoustic evaluation is valuable for guiding the treatment of maxillofacial defects and determining the effectiveness of rehabilitation with an obturator prosthesis. Model simulations are important in terms of pre-surgical planning and pre- and post-operative speech function. This study aimed to evaluate the acoustic characteristics of voice generated by an articulation simulation system using a vocal tract model with or without artificial maxillectomy defects. More specifically, we aimed to establish a speech simulation system for maxillectomy defect models that both surgeons and maxillofacial prosthodontists can use in guiding treatment planning. Artificially simulated maxillectomy defects were prepared according to Aramany's classification (Classes I-VI) in a three-dimensional vocal tract plaster model of a subject uttering the vowel /a/. Formant and nasalance acoustic data were analysed using Computerized Speech Lab and the Nasometer, respectively. Formants and nasalance of simulated /a/ sounds were successfully detected and analysed. Values of Formants 1 and 2 for the non-defect model were 675.43 and 976.64 Hz, respectively. Median values of Formants 1 and 2 for the defect models were 634.36 and 1026.84 Hz, respectively. Nasalance was 11% in the non-defect model, whereas median nasalance was 28% in the defect models. The results suggest that an articulation simulation system can be used to help surgeons and maxillofacial prosthodontists to plan post-surgical defects that will be facilitate maxillofacial rehabilitation. © 2015 John Wiley & Sons Ltd.

WDM Systems and Networks Modeling, Simulation, Design and Engineering

CERN Document Server

Ellinas, Georgios; Roudas, Ioannis

2012-01-01

WDM Systems and Networks: Modeling, Simulation, Design and Engineering provides readers with the basic skills, concepts, and design techniques used to begin design and engineering of optical communication systems and networks at various layers. The latest semi-analytical system simulation techniques are applied to optical WDM systems and networks, and a review of the various current areas of optical communications is presented. Simulation is mixed with experimental verification and engineering to present the industry as well as state-of-the-art research. This contributed volume is divided into three parts, accommodating different readers interested in various types of networks and applications. The first part of the book presents modeling approaches and simulation tools mainly for the physical layer including transmission effects, devices, subsystems, and systems), whereas the second part features more engineering/design issues for various types of optical systems including ULH, access, and in-building system...

Guidelines for Reproducibly Building and Simulating Systems Biology Models.

Science.gov (United States)

Medley, J Kyle; Goldberg, Arthur P; Karr, Jonathan R

2016-10-01

Reproducibility is the cornerstone of the scientific method. However, currently, many systems biology models cannot easily be reproduced. This paper presents methods that address this problem. We analyzed the recent Mycoplasma genitalium whole-cell (WC) model to determine the requirements for reproducible modeling. We determined that reproducible modeling requires both repeatable model building and repeatable simulation. New standards and simulation software tools are needed to enhance and verify the reproducibility of modeling. New standards are needed to explicitly document every data source and assumption, and new deterministic parallel simulation tools are needed to quickly simulate large, complex models. We anticipate that these new standards and software will enable researchers to reproducibly build and simulate more complex models, including WC models.

MODELING SIMULATION AND PERFORMANCE STUDY OF GRIDCONNECTED PHOTOVOLTAIC ENERGY SYSTEM

OpenAIRE

Nagendra K; Karthik J; Keerthi Rao C; Kumar Raja Pemmadi

2017-01-01

This paper presents Modeling Simulation of grid connected Photovoltaic Energy System and performance study using MATLAB/Simulink. The Photovoltaic energy system is considered in three main parts PV Model, Power conditioning System and Grid interface. The Photovoltaic Model is inter-connected with grid through full scale power electronic devices. The simulation is conducted on the PV energy system at normal temperature and at constant load by using MATLAB.

Modeling and simulation for RF system design

CERN Document Server

Frevert, Ronny; Jancke, Roland; Knöchel, Uwe; Schwarz, Peter; Kakerow, Ralf; Darianian, Mohsen

2005-01-01

Focusing on RF specific modeling and simulation methods, and system and circuit level descriptions, this work contains application-oriented training material. Accompanied by a CD- ROM, it combines the presentation of a mixed-signal design flow, an introduction into VHDL-AMS and Verilog-A, and the application of commercially available simulators.

Dynamic wind turbine models in power system simulation tool

DEFF Research Database (Denmark)

Hansen, A.; Jauch, Clemens; Soerensen, P.

The present report describes the dynamic wind turbine models implemented in the power system simulation tool DIgSILENT. The developed models are a part of the results of a national research project, whose overall objective is to create a model database in different simulation tools. The report...

Strategy and gaps for modeling, simulation, and control of hybrid systems

Energy Technology Data Exchange (ETDEWEB)

Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Garcia, Humberto E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hovsapian, Rob [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinoshita, Robert [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mesina, George L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bragg-Sitton, Shannon M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Boardman, Richard D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-04-01

The purpose of this report is to establish a strategy for modeling and simulation of candidate hybrid energy systems. Modeling and simulation is necessary to design, evaluate, and optimize the system technical and economic performance. Accordingly, this report first establishes the simulation requirements to analysis candidate hybrid systems. Simulation fidelity levels are established based on the temporal scale, real and synthetic data availability or needs, solution accuracy, and output parameters needed to evaluate case-specific figures of merit. Accordingly, the associated computational and co-simulation resources needed are established; including physical models when needed, code assembly and integrated solutions platforms, mathematical solvers, and data processing. This report first attempts to describe the figures of merit, systems requirements, and constraints that are necessary and sufficient to characterize the grid and hybrid systems behavior and market interactions. Loss of Load Probability (LOLP) and effective cost of Effective Cost of Energy (ECE), as opposed to the standard Levelized Cost of Electricty (LCOE), are introduced as technical and economical indices for integrated energy system evaluations. Financial assessment methods are subsequently introduced for evaluation of non-traditional, hybrid energy systems. Algorithms for coupled and iterative evaluation of the technical and economic performance are subsequently discussed. This report further defines modeling objectives, computational tools, solution approaches, and real-time data collection and processing (in some cases using real test units) that will be required to model, co-simulate, and optimize; (a) an energy system components (e.g., power generation unit, chemical process, electricity management unit), (b) system domains (e.g., thermal, electrical or chemical energy generation, conversion, and transport), and (c) systems control modules. Co-simulation of complex, tightly coupled

Biocellion: accelerating computer simulation of multicellular biological system models.

Science.gov (United States)

Kang, Seunghwa; Kahan, Simon; McDermott, Jason; Flann, Nicholas; Shmulevich, Ilya

2014-11-01

Biological system behaviors are often the outcome of complex interactions among a large number of cells and their biotic and abiotic environment. Computational biologists attempt to understand, predict and manipulate biological system behavior through mathematical modeling and computer simulation. Discrete agent-based modeling (in combination with high-resolution grids to model the extracellular environment) is a popular approach for building biological system models. However, the computational complexity of this approach forces computational biologists to resort to coarser resolution approaches to simulate large biological systems. High-performance parallel computers have the potential to address the computing challenge, but writing efficient software for parallel computers is difficult and time-consuming. We have developed Biocellion, a high-performance software framework, to solve this computing challenge using parallel computers. To support a wide range of multicellular biological system models, Biocellion asks users to provide their model specifics by filling the function body of pre-defined model routines. Using Biocellion, modelers without parallel computing expertise can efficiently exploit parallel computers with less effort than writing sequential programs from scratch. We simulate cell sorting, microbial patterning and a bacterial system in soil aggregate as case studies. Biocellion runs on x86 compatible systems with the 64 bit Linux operating system and is freely available for academic use. Visit http://biocellion.com for additional information. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Novel Methodology for Functional Modeling and Simulation of Wireless Embedded Systems

Directory of Open Access Journals (Sweden)

Sosa Morales Emma

2008-01-01

Full Text Available Abstract A novel methodology is presented for the modeling and the simulation of wireless embedded systems. Tight interaction between the analog and the digital functionality makes the design and verification of such systems a real challenge. The applied methodology brings together the functional models of the baseband algorithms written in C language with the circuit descriptions at behavioral level in Verilog or Verilog-AMS for the system simulations in a single kernel environment. The physical layer of an ultrawideband system has been successfully modeled and simulated. The results confirm that this methodology provides a standardized framework in order to efficiently and accurately simulate complex mixed signal applications for embedded systems.

System-of-Systems Approach for Integrated Energy Systems Modeling and Simulation: Preprint

Energy Technology Data Exchange (ETDEWEB)

Mittal, Saurabh; Ruth, Mark; Pratt, Annabelle; Lunacek, Monte; Krishnamurthy, Dheepak; Jones, Wesley

2015-08-21

Today’s electricity grid is the most complex system ever built—and the future grid is likely to be even more complex because it will incorporate distributed energy resources (DERs) such as wind, solar, and various other sources of generation and energy storage. The complexity is further augmented by the possible evolution to new retail market structures that provide incentives to owners of DERs to support the grid. To understand and test new retail market structures and technologies such as DERs, demand-response equipment, and energy management systems while providing reliable electricity to all customers, an Integrated Energy System Model (IESM) is being developed at NREL. The IESM is composed of a power flow simulator (GridLAB-D), home energy management systems implemented using GAMS/Pyomo, a market layer, and hardware-in-the-loop simulation (testing appliances such as HVAC, dishwasher, etc.). The IESM is a system-of-systems (SoS) simulator wherein the constituent systems are brought together in a virtual testbed. We will describe an SoS approach for developing a distributed simulation environment. We will elaborate on the methodology and the control mechanisms used in the co-simulation illustrated by a case study.

Modular Modelling and Simulation Approach - Applied to Refrigeration Systems

DEFF Research Database (Denmark)

Sørensen, Kresten Kjær; Stoustrup, Jakob

2008-01-01

This paper presents an approach to modelling and simulation of the thermal dynamics of a refrigeration system, specifically a reefer container. A modular approach is used and the objective is to increase the speed and flexibility of the developed simulation environment. The refrigeration system...

Cognitive models embedded in system simulation models

International Nuclear Information System (INIS)

Siegel, A.I.; Wolf, J.J.

1982-01-01

If we are to discuss and consider cognitive models, we must first come to grips with two questions: (1) What is cognition; (2) What is a model. Presumably, the answers to these questions can provide a basis for defining a cognitive model. Accordingly, this paper first places these two questions into perspective. Then, cognitive models are set within the context of computer simulation models and a number of computer simulations of cognitive processes are described. Finally, pervasive issues are discussed vis-a-vis cognitive modeling in the computer simulation context

Modeling and Simulation of Power Distribution System in More Electric Aircraft

Directory of Open Access Journals (Sweden)

Zhangang Yang

2015-01-01

Full Text Available The More Electric Aircraft concept is a fast-developing trend in modern aircraft industry. With this new concept, the performance of the aircraft can be further optimized and meanwhile the operating and maintenance cost will be decreased effectively. In order to optimize the power system integrity and have the ability to investigate the performance of the overall system in any possible situations, one accurate simulation model of the aircraft power system will be very helpful and necessary. This paper mainly introduces a method to build a simulation model for the power distribution system, which is based on detailed component models. The power distribution system model consists of power generation unit, transformer rectifier unit, DC-DC converter unit, and DC-AC inverter unit. In order to optimize the performance of the power distribution system and improve the quality of the distributed power, a feedback control network is designed based on the characteristics of the power distribution system. The simulation result indicates that this new simulation model is well designed and it works accurately. Moreover, steady state performance and transient state performance of the model can fulfill the requirements of aircraft power distribution system in the realistic application.

Modeling and Simulation for Mission Operations Work System Design

Science.gov (United States)

Sierhuis, Maarten; Clancey, William J.; Seah, Chin; Trimble, Jay P.; Sims, Michael H.

2003-01-01

Work System analysis and design is complex and non-deterministic. In this paper we describe Brahms, a multiagent modeling and simulation environment for designing complex interactions in human-machine systems. Brahms was originally conceived as a business process design tool that simulates work practices, including social systems of work. We describe our modeling and simulation method for mission operations work systems design, based on a research case study in which we used Brahms to design mission operations for a proposed discovery mission to the Moon. We then describe the results of an actual method application project-the Brahms Mars Exploration Rover. Space mission operations are similar to operations of traditional organizations; we show that the application of Brahms for space mission operations design is relevant and transferable to other types of business processes in organizations.

Generalized math model for simulation of high-altitude balloon systems

Science.gov (United States)

Nigro, N. J.; Elkouh, A. F.; Hinton, D. E.; Yang, J. K.

1985-01-01

Balloon systems have proved to be a cost-effective means for conducting research experiments (e.g., infrared astronomy) in the earth's atmosphere. The purpose of this paper is to present a generalized mathematical model that can be used to simulate the motion of these systems once they have attained float altitude. The resulting form of the model is such that the pendulation and spin motions of the system are uncoupled and can be analyzed independently. The model is evaluated by comparing the simulation results with data obtained from an actual balloon system flown by NASA.

Modelling and simulation of process control systems for WWER

Energy Technology Data Exchange (ETDEWEB)

Pangelov, N [Energoproekt, Sofia (Bulgaria)

1996-12-31

A dynamic modelling method for simulation of process control system is developed (method for identification). It is based on the least squares method and highly efficient linear uninterrupted differential equations. The method has the following advantages: there are no significant limitations in the type of input/output signals and in the length of data time series; identification at none zero initial condition is possible; on-line identification is possible; a high accuracy is observed in case of noise. On the basis of real experiments and data time series simulated with known computer codes it is possible to construct highly efficient models of different systems for solving the following problems: real time simulation with high accuracy for training purposes; estimation of immeasurable parameters important to safety; malfunction diagnostics based on plant dynamics; prediction of dynamic behaviour; control vector estimation in regime adviser. Two real applications of this method are described: in dynamic behaviour modelling for steam generator level, and in creating of a Process Control System Simulator (PCSS) based on KASKAD-2 for WWER-1000 units of the Kozloduy NPP. 6 refs., 8 figs.

Performance modeling & simulation of complex systems (A systems engineering design & analysis approach)

Science.gov (United States)

Hall, Laverne

1995-01-01

Modeling of the Multi-mission Image Processing System (MIPS) will be described as an example of the use of a modeling tool to design a distributed system that supports multiple application scenarios. This paper examines: (a) modeling tool selection, capabilities, and operation (namely NETWORK 2.5 by CACl), (b) pointers for building or constructing a model and how the MIPS model was developed, (c) the importance of benchmarking or testing the performance of equipment/subsystems being considered for incorporation the design/architecture, (d) the essential step of model validation and/or calibration using the benchmark results, (e) sample simulation results from the MIPS model, and (f) how modeling and simulation analysis affected the MIPS design process by having a supportive and informative impact.

An Interactive Teaching System for Bond Graph Modeling and Simulation in Bioengineering

Science.gov (United States)

Roman, Monica; Popescu, Dorin; Selisteanu, Dan

2013-01-01

The objective of the present work was to implement a teaching system useful in modeling and simulation of biotechnological processes. The interactive system is based on applications developed using 20-sim modeling and simulation software environment. A procedure for the simulation of bioprocesses modeled by bond graphs is proposed and simulators…

Anatomy and Physiology of Multiscale Modeling and Simulation in Systems Medicine.

Science.gov (United States)

Mizeranschi, Alexandru; Groen, Derek; Borgdorff, Joris; Hoekstra, Alfons G; Chopard, Bastien; Dubitzky, Werner

2016-01-01

Systems medicine is the application of systems biology concepts, methods, and tools to medical research and practice. It aims to integrate data and knowledge from different disciplines into biomedical models and simulations for the understanding, prevention, cure, and management of complex diseases. Complex diseases arise from the interactions among disease-influencing factors across multiple levels of biological organization from the environment to molecules. To tackle the enormous challenges posed by complex diseases, we need a modeling and simulation framework capable of capturing and integrating information originating from multiple spatiotemporal and organizational scales. Multiscale modeling and simulation in systems medicine is an emerging methodology and discipline that has already demonstrated its potential in becoming this framework. The aim of this chapter is to present some of the main concepts, requirements, and challenges of multiscale modeling and simulation in systems medicine.

Simulator for candu600 fuel handling system. the experimental model

International Nuclear Information System (INIS)

Marinescu, N.; Predescu, D.; Valeca, S.

2013-01-01

A main way to increase the nuclear plant safety is related to selection and continuous training of the operation staff. In this order, the computer programs for training, testing and evaluation of the knowledge get, or training simulators including the advanced analytical models of the technological systems are using. The Institute for Nuclear Research from Pitesti, Romania intend to design and build an Fuel Handling Simulator at his F/M Head Test Rig facility, that will be used for training of operating personnel. This paper presents simulated system, advantages to use the simulator, and the experimental model of simulator, that has been built to allows setting of the requirements and fabrication details, especially for the software kit that will be designed and implement on main simulator. (authors)

Co-simulation of dynamic systems in parallel and serial model configurations

International Nuclear Information System (INIS)

Sweafford, Trevor; Yoon, Hwan Sik

2013-01-01

Recent advancement in simulation software and computation hardware make it realizable to simulate complex dynamic systems comprised of multiple submodels developed in different modeling languages. The so-called co-simulation enables one to study various aspects of a complex dynamic system with heterogeneous submodels in a cost-effective manner. Among several different model configurations for co-simulation, synchronized parallel configuration is regarded to expedite the simulation process by simulation multiple sub models concurrently on a multi core processor. In this paper, computational accuracies as well as computation time are studied for three different co-simulation frameworks : integrated, serial, and parallel. for this purpose, analytical evaluations of the three different methods are made using the explicit Euler method and then they are applied to two-DOF mass-spring systems. The result show that while the parallel simulation configuration produces the same accurate results as the integrated configuration, results of the serial configuration, results of the serial configuration show a slight deviation. it is also shown that the computation time can be reduced by running simulation in the parallel configuration. Therefore, it can be concluded that the synchronized parallel simulation methodology is the best for both simulation accuracy and time efficiency.

Design, modeling, simulation and evaluation of a distributed energy system

Science.gov (United States)

Cultura, Ambrosio B., II

This dissertation presents the design, modeling, simulation and evaluation of distributed energy resources (DER) consisting of photovoltaics (PV), wind turbines, batteries, a PEM fuel cell and supercapacitors. The distributed energy resources installed at UMass Lowell consist of the following: 2.5kW PV, 44kWhr lead acid batteries and 1500W, 500W & 300W wind turbines, which were installed before year 2000. Recently added to that are the following: 10.56 kW PV array, 2.4 kW wind turbine, 29 kWhr Lead acid batteries, a 1.2 kW PEM fuel cell and 4-140F supercapacitors. Each newly added energy resource has been designed, modeled, simulated and evaluated before its integration into the existing PV/Wind grid-connected system. The Mathematical and Simulink model of each system was derived and validated by comparing the simulated and experimental results. The Simulated results of energy generated from a 10.56kW PV system are in good agreement with the experimental results. A detailed electrical model of a 2.4kW wind turbine system equipped with a permanent magnet generator, diode rectifier, boost converter and inverter is presented. The analysis of the results demonstrates the effectiveness of the constructed simulink model, and can be used to predict the performance of the wind turbine. It was observed that a PEM fuel cell has a very fast response to load changes. Moreover, the model has validated the actual operation of the PEM fuel cell, showing that the simulated results in Matlab Simulink are consistent with the experimental results. The equivalent mathematical equation, derived from an electrical model of the supercapacitor, is used to simulate its voltage response. The model is completely capable of simulating its voltage behavior, and can predict the charge time and discharge time of voltages on the supercapacitor. The bi-directional dc-dc converter was designed in order to connect the 48V battery bank storage to the 24V battery bank storage. This connection was

Teaching modelling of distributed information and control systems to students using the method of simulation modelling

Directory of Open Access Journals (Sweden)

A. V. Gabalin

2017-01-01

Full Text Available Mathematical modelling is one of the most effective means to study the complex systems and processes. One of the most convenient means of mathematical modelling used in the analysis of functioning of systems of this class are simulation models that describe the structure and behavior of the system in the form of a program for the PC and allow conducting computer experiments with the aim of obtaining the necessary data on the functioning of the elements and the system as a whole during certain time intervals. Currently, the simulation tools market presents a large number of different simulation systems. However, the selection of suitable tools is very important. Specialized programs in particular are GPSS World, MATLAB/ Simulink, and AnyLogic. Distributed information and control systems (ICS are dispersed in space multifunctional coherent set of stationary and moving elements with developed technical means of reception, transmission and processing of information. The task is to determine a rational structure of ICS, system-planned indicators of quality of development and functioning of which meet specified requirements under given structural constraints, characteristics of information flows, and parameters of technical tools. For experimental research of functioning processes of the described system a simulation model was developed. This model allows obtaining and evaluating such functional characteristics as the degree of technical means utilization, waiting time of information in queues for service, the level of efficiency of transmission and processing of information, the time of forming a single media and etc. The model also allows evaluating the performance of the system depending on the flight schedule, flight paths, characteristics of technical means, the system structure, failure of individual elements and depending on other parameters. The developed simulation model in GPSS allows students to master the subject area deeply enough – the

Interactive Dynamic-System Simulation

CERN Document Server

Korn, Granino A

2010-01-01

Showing you how to use personal computers for modeling and simulation, Interactive Dynamic-System Simulation, Second Edition provides a practical tutorial on interactive dynamic-system modeling and simulation. It discusses how to effectively simulate dynamical systems, such as aerospace vehicles, power plants, chemical processes, control systems, and physiological systems. Written by a pioneer in simulation, the book introduces dynamic-system models and explains how software for solving differential equations works. After demonstrating real simulation programs with simple examples, the author

An Integrated Simulation Tool for Modeling the Human Circulatory System

Science.gov (United States)

Asami, Ken'ichi; Kitamura, Tadashi

This paper presents an integrated simulation of the circulatory system in physiological movement. The large circulatory system model includes principal organs and functional units in modules in which comprehensive physiological changes such as nerve reflexes, temperature regulation, acid/base balance, O2/CO2 balance, and exercise are simulated. A beat-by-beat heart model, in which the corresponding electrical circuit problems are solved by a numerical analytic method, enables calculation of pulsatile blood flow to the major organs. The integration of different perspectives on physiological changes makes this simulation model applicable for the microscopic evaluation of blood flow under various conditions in the human body.

Dynamic wind turbine models in power system simulation tool DIgSILENT

Energy Technology Data Exchange (ETDEWEB)

Hansen, A.C.; Jauch, C.; Soerensen, P.; Iov, F.; Blaabjerg, F.

2003-12-01

The present report describes the dynamic wind turbine models implemented in the power system simulation tool DIgSILENT (Version 12.0). The developed models are a part of the results of a national research project, whose overall objective is to create a model database in different simulation tools. This model database should be able to support the analysis of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The report provides a description of the wind turbines modelling, both at a component level and at a system level. The report contains both the description of DIgSILENT built-in models for the electrical components of a grid connected wind turbine (e.g. induction generators, power converters, transformers) and the models developed by the user, in the dynamic simulation language DSL of DIgSILENT, for the non-electrical components of the wind turbine (wind model, aerodynamic model, mechanical model). The initialisation issues on the wind turbine models into the power system simulation are also presented. However, the main attention in this report is drawn to the modelling at the system level of two wind turbine concepts: 1. Active stall wind turbine with induction generator 2. Variable speed, variable pitch wind turbine with doubly fed induction generator. These wind turbine concept models can be used and even extended for the study of different aspects, e.g. the assessment of power quality, control strategies, connection of the wind turbine at different types of grid and storage systems. For both these two concepts, control strategies are developed and implemented, their performance assessed and discussed by means of simulations. (au)

A model selection support system for numerical simulations of nuclear thermal-hydraulics

International Nuclear Information System (INIS)

Gofuku, Akio; Shimizu, Kenji; Sugano, Keiji; Yoshikawa, Hidekazu; Wakabayashi, Jiro

1990-01-01

In order to execute efficiently a dynamic simulation of a large-scaled engineering system such as a nuclear power plant, it is necessary to develop intelligent simulation support system for all phases of the simulation. This study is concerned with the intelligent support for the program development phase and is engaged in the adequate model selection support method by applying AI (Artificial Intelligence) techniques to execute a simulation consistent with its purpose and conditions. A proto-type expert system to support the model selection for numerical simulations of nuclear thermal-hydraulics in the case of cold leg small break loss-of-coolant accident of PWR plant is now under development on a personal computer. The steps to support the selection of both fluid model and constitutive equations for the drift flux model have been developed. Several cases of model selection were carried out and reasonable model selection results were obtained. (author)

Robustness of Component Models in Energy System Simulators

DEFF Research Database (Denmark)

Elmegaard, Brian

2003-01-01

During the development of the component-based energy system simulator DNA (Dynamic Network Analysis), several obstacles to easy use of the program have been observed. Some of these have to do with the nature of the program being based on a modelling language, not a graphical user interface (GUI......). Others have to do with the interaction between models of the nature of the substances in an energy system (e.g., fuels, air, flue gas), models of the components in a system (e.g., heat exchangers, turbines, pumps), and the solver for the system of equations. This paper proposes that the interaction...

Control-relevant modeling and simulation of a SOFC-GT hybrid system

OpenAIRE

Rambabu Kandepu; Lars Imsland; Christoph Stiller; Bjarne A. Foss; Vinay Kariwala

2006-01-01

In this paper, control-relevant models of the most important components in a SOFC-GT hybrid system are described. Dynamic simulations are performed on the overall hybrid system. The model is used to develop a simple control structure, but the simulations show that more elaborate control is needed.

Hybrid simulation models for data-intensive systems

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00473067

Data-intensive systems are used to access and store massive amounts of data by combining the storage resources of multiple data-centers, usually deployed all over the world, in one system. This enables users to utilize these massive storage capabilities in a simple and efficient way. However, with the growth of these systems it becomes a hard problem to estimate the effects of modifications to the system, such as data placement algorithms or hardware upgrades, and to validate these changes for potential side effects. This thesis addresses the modeling of operational data-intensive systems and presents a novel simulation model which estimates the performance of system operations. The running example used throughout this thesis is the data-intensive system Rucio, which is used as the data man- agement system of the ATLAS experiment at CERN’s Large Hadron Collider. Existing system models in literature are not applicable to data-intensive workflows, as they only consider computational workflows or make assumpti...

Tidal simulation using regional ocean modeling systems (ROMS)

Science.gov (United States)

Wang, Xiaochun; Chao, Yi; Li, Zhijin; Dong, Changming; Farrara, John; McWilliams, James C.; Shum, C. K.; Wang, Yu; Matsumoto, Koji; Rosenfeld, Leslie K.;

Control-relevant modeling and simulation of a SOFC-GT hybrid system

Directory of Open Access Journals (Sweden)

Rambabu Kandepu

2006-07-01

Full Text Available In this paper, control-relevant models of the most important components in a SOFC-GT hybrid system are described. Dynamic simulations are performed on the overall hybrid system. The model is used to develop a simple control structure, but the simulations show that more elaborate control is needed.

An Advanced HIL Simulation Battery Model for Battery Management System Testing

DEFF Research Database (Denmark)

Barreras, Jorge Varela; Fleischer, Christian; Christensen, Andreas Elkjær

2016-01-01

Developers and manufacturers of battery management systems (BMSs) require extensive testing of controller Hardware (HW) and Software (SW), such as analog front-end and performance of generated control code. In comparison with the tests conducted on real batteries, tests conducted on a state......-of-the-art hardware-in-the-loop (HIL) simulator can be more cost and time effective, easier to reproduce, and safer beyond the normal range of operation, especially at early stages in the development process or during fault insertion. In this paper, an HIL simulation battery model is developed for purposes of BMS...... testing on a commercial HIL simulator. A multicell electrothermal Li-ion battery (LIB) model is integrated in a system-level simulation. Then, the LIB system model is converted to C code and run in real time with the HIL simulator. Finally, in order to demonstrate the capabilities of the setup...

Virtual Systems Pharmacology (ViSP software for mechanistic system-level model simulations

Directory of Open Access Journals (Sweden)

Sergey eErmakov

2014-10-01

Full Text Available Multiple software programs are available for designing and running large scale system-level pharmacology models used in the drug development process. Depending on the problem, scientists may be forced to use several modeling tools that could increase model development time, IT costs and so on. Therefore it is desirable to have a single platform that allows setting up and running large-scale simulations for the models that have been developed with different modeling tools. We developed a workflow and a software platform in which a model file is compiled into a self-contained executable that is no longer dependent on the software that was used to create the model. At the same time the full model specifics is preserved by presenting all model parameters as input parameters for the executable. This platform was implemented as a model agnostic, therapeutic area agnostic and web-based application with a database back-end that can be used to configure, manage and execute large-scale simulations for multiple models by multiple users. The user interface is designed to be easily configurable to reflect the specifics of the model and the user’s particular needs and the back-end database has been implemented to store and manage all aspects of the systems, such as Models, Virtual Patients, User Interface Settings, and Results. The platform can be adapted and deployed on an existing cluster or cloud computing environment. Its use was demonstrated with a metabolic disease systems pharmacology model that simulates the effects of two antidiabetic drugs, metformin and fasiglifam, in type 2 diabetes mellitus patients.

Unified Approach to Modeling and Simulation of Space Communication Networks and Systems

Science.gov (United States)

Barritt, Brian; Bhasin, Kul; Eddy, Wesley; Matthews, Seth

2010-01-01

Network simulator software tools are often used to model the behaviors and interactions of applications, protocols, packets, and data links in terrestrial communication networks. Other software tools that model the physics, orbital dynamics, and RF characteristics of space systems have matured to allow for rapid, detailed analysis of space communication links. However, the absence of a unified toolset that integrates the two modeling approaches has encumbered the systems engineers tasked with the design, architecture, and analysis of complex space communication networks and systems. This paper presents the unified approach and describes the motivation, challenges, and our solution - the customization of the network simulator to integrate with astronautical analysis software tools for high-fidelity end-to-end simulation. Keywords space; communication; systems; networking; simulation; modeling; QualNet; STK; integration; space networks

Modeling, Simulation, and Experiment of Switched Reluctance Ocean Current Generator System

Directory of Open Access Journals (Sweden)

Hao Chen

2013-01-01

Full Text Available This paper presents nonlinear simulation model of switched reluctance (SR ocean current generator system on MATLAB/SIMULINK with describing the structure of generator system. The developed model is made up of main model, rotor position calculation module, controller module, gate module, power converter module, phase windings module, flux-linkage module, torque module, and power calculation module. The magnetization curves obtained by two-dimensional finite-element electromagnetic field calculation and the conjugated magnetic energy graphics obtained from the three-dimensional graphics of flux linkage are stored in the “Lookup Table” modules on MATLAB/SIMULINK. The hardware of the developed three-phase 12/8 structure SR ocean current generator system prototype with the experimental platform is presented. The simulation of the prototype is performed by the developed models, and the experiments have been carried out under the same condition with different output power, turn-off angle, and rotor speed. The simulated phase current waveforms agree well with the tested phase current waveforms experimentally. The simulated output voltage curves agree well with the tested output voltage curves experimentally. It is shown that the developed nonlinear simulation model of the three-phase 12/8 structure SR ocean current generator system is valid.

Dynamic information architecture system (DIAS) : multiple model simulation management

International Nuclear Information System (INIS)

Simunich, K. L.; Sydelko, P.; Dolph, J.; Christiansen, J.

2002-01-01

Dynamic Information Architecture System (DIAS) is a flexible, extensible, object-based framework for developing and maintaining complex multidisciplinary simulations of a wide variety of application contexts. The modeling domain of a specific DIAS-based simulation is determined by (1) software Entity (domain-specific) objects that represent the real-world entities that comprise the problem space (atmosphere, watershed, human), and (2) simulation models and other data processing applications that express the dynamic behaviors of the domain entities. In DIAS, models communicate only with Entity objects, never with each other. Each Entity object has a number of Parameter and Aspect (of behavior) objects associated with it. The Parameter objects contain the state properties of the Entity object. The Aspect objects represent the behaviors of the Entity object and how it interacts with other objects. DIAS extends the ''Object'' paradigm by abstraction of the object's dynamic behaviors, separating the ''WHAT'' from the ''HOW.'' DIAS object class definitions contain an abstract description of the various aspects of the object's behavior (the WHAT), but no implementation details (the HOW). Separate DIAS models/applications carry the implementation of object behaviors (the HOW). Any model deemed appropriate, including existing legacy-type models written in other languages, can drive entity object behavior. The DIAS design promotes plug-and-play of alternative models, with minimal recoding of existing applications. The DIAS Context Builder object builds a constructs or scenario for the simulation, based on developer specification and user inputs. Because DIAS is a discrete event simulation system, there is a Simulation Manager object with which all events are processed. Any class that registers to receive events must implement an event handler (method) to process the event during execution. Event handlers can schedule other events; create or remove Entities from the

Systems modeling and simulation applications for critical care medicine

Science.gov (United States)

2012-01-01

Critical care delivery is a complex, expensive, error prone, medical specialty and remains the focal point of major improvement efforts in healthcare delivery. Various modeling and simulation techniques offer unique opportunities to better understand the interactions between clinical physiology and care delivery. The novel insights gained from the systems perspective can then be used to develop and test new treatment strategies and make critical care delivery more efficient and effective. However, modeling and simulation applications in critical care remain underutilized. This article provides an overview of major computer-based simulation techniques as applied to critical care medicine. We provide three application examples of different simulation techniques, including a) pathophysiological model of acute lung injury, b) process modeling of critical care delivery, and c) an agent-based model to study interaction between pathophysiology and healthcare delivery. Finally, we identify certain challenges to, and opportunities for, future research in the area. PMID:22703718

Systems modeling and simulation applications for critical care medicine.

Science.gov (United States)

Dong, Yue; Chbat, Nicolas W; Gupta, Ashish; Hadzikadic, Mirsad; Gajic, Ognjen

2012-06-15

Critical care delivery is a complex, expensive, error prone, medical specialty and remains the focal point of major improvement efforts in healthcare delivery. Various modeling and simulation techniques offer unique opportunities to better understand the interactions between clinical physiology and care delivery. The novel insights gained from the systems perspective can then be used to develop and test new treatment strategies and make critical care delivery more efficient and effective. However, modeling and simulation applications in critical care remain underutilized. This article provides an overview of major computer-based simulation techniques as applied to critical care medicine. We provide three application examples of different simulation techniques, including a) pathophysiological model of acute lung injury, b) process modeling of critical care delivery, and c) an agent-based model to study interaction between pathophysiology and healthcare delivery. Finally, we identify certain challenges to, and opportunities for, future research in the area.

Modelling physics detectors in a computer aided design system for simulation purposes

International Nuclear Information System (INIS)

Ahvenainen, J.; Oksakivi, T.; Vuoskoski, J.

1995-01-01

The possibility of transferring physics detector models from computer aided design systems into physics simulation packages like GEANT is receiving increasing attention. The problem of exporting detector models constructed in CAD systems into GEANT is well known. We discuss the problem and describe an application, called DDT, which allows one to design detector models in a CAD system and then transfer the models into GEANT for simulation purposes. (orig.)

Modeling and Simulation of a Modified Quadruple Tank System

DEFF Research Database (Denmark)

Mohd. Azam, Sazuan Nazrah; Jørgensen, John Bagterp

2015-01-01

to model and control. In this paper, a modified quadruple-tank system has been described, all the important variables has been outlined and a mathematical model has been presented. We developed deterministic and stochastic models using differential equations and simulate the models using Matlab...

Real time modeling, simulation and control of dynamical systems

CERN Document Server

Mughal, Asif Mahmood

2016-01-01

This book introduces modeling and simulation of linear time invariant systems and demonstrates how these translate to systems engineering, mechatronics engineering, and biomedical engineering. It is organized into nine chapters that follow the lectures used for a one-semester course on this topic, making it appropriate for students as well as researchers. The author discusses state space modeling derived from two modeling techniques and the analysis of the system and usage of modeling in control systems design. It also contains a unique chapter on multidisciplinary energy systems with a special focus on bioengineering systems and expands upon how the bond graph augments research in biomedical and bio-mechatronics systems.

Simulation and analysis of a model dinoflagellate predator-prey system

Science.gov (United States)

Mazzoleni, M. J.; Antonelli, T.; Coyne, K. J.; Rossi, L. F.

2015-12-01

This paper analyzes the dynamics of a model dinoflagellate predator-prey system and uses simulations to validate theoretical and experimental studies. A simple model for predator-prey interactions is derived by drawing upon analogies from chemical kinetics. This model is then modified to account for inefficiencies in predation. Simulation results are shown to closely match the model predictions. Additional simulations are then run which are based on experimental observations of predatory dinoflagellate behavior, and this study specifically investigates how the predatory dinoflagellate Karlodinium veneficum uses toxins to immobilize its prey and increase its feeding rate. These simulations account for complex dynamics that were not included in the basic models, and the results from these computational simulations closely match the experimentally observed predatory behavior of K. veneficum and reinforce the notion that predatory dinoflagellates utilize toxins to increase their feeding rate.

Modelling and simulation of complex sociotechnical systems: envisioning and analysing work environments

Science.gov (United States)

Hettinger, Lawrence J.; Kirlik, Alex; Goh, Yang Miang; Buckle, Peter

2015-01-01

Accurate comprehension and analysis of complex sociotechnical systems is a daunting task. Empirically examining, or simply envisioning the structure and behaviour of such systems challenges traditional analytic and experimental approaches as well as our everyday cognitive capabilities. Computer-based models and simulations afford potentially useful means of accomplishing sociotechnical system design and analysis objectives. From a design perspective, they can provide a basis for a common mental model among stakeholders, thereby facilitating accurate comprehension of factors impacting system performance and potential effects of system modifications. From a research perspective, models and simulations afford the means to study aspects of sociotechnical system design and operation, including the potential impact of modifications to structural and dynamic system properties, in ways not feasible with traditional experimental approaches. This paper describes issues involved in the design and use of such models and simulations and describes a proposed path forward to their development and implementation. Practitioner Summary: The size and complexity of real-world sociotechnical systems can present significant barriers to their design, comprehension and empirical analysis. This article describes the potential advantages of computer-based models and simulations for understanding factors that impact sociotechnical system design and operation, particularly with respect to process and occupational safety. PMID:25761227

Dynamic wind turbine models in power system simulation tool DIgSILENT

DEFF Research Database (Denmark)

Hansen, A.D.; Jauch, C.; Sørensen, Poul Ejnar

2004-01-01

. This model database should be able to support the analysis of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The reportprovides a description of the wind turbines modelling, both at a component level and at a system level......-electrical components of the wind turbine (wind model, aerodynamic model, mechanical model). Theinitialisation issues on the wind turbine models into the power system simulation are also presented. However, the main attention in this report is drawn to the modelling at the system level of two wind turbine concepts: 1...... of the wind turbine at different types of grid and storage systems. For both these two concepts, control strategies are developed and implemented, their performance assessed and discussed by means of simulations....

Control-Oriented Models for Real-Time Simulation of Automotive Transmission Systems

Directory of Open Access Journals (Sweden)

Cavina N.

2015-01-01

Full Text Available A control-oriented model of a Dual Clutch Transmission (DCT was developed for real-time Hardware In the Loop (HIL applications, to support model-based development of the DCT controller and to systematically test its performance. The model is an innovative attempt to reproduce the fast dynamics of the actuation system while maintaining a simulation step size large enough for real-time applications. The model comprehends a detailed physical description of hydraulic circuit, clutches, synchronizers and gears, and simplified vehicle and internal combustion engine sub-models. As the oil circulating in the system has a large bulk modulus, the pressure dynamics are very fast, possibly causing instability in a real-time simulation; the same challenge involves the servo valves dynamics, due to the very small masses of the moving elements. Therefore, the hydraulic circuit model has been modified and simplified without losing physical validity, in order to adapt it to the real-time simulation requirements. The results of offline simulations have been compared to on-board measurements to verify the validity of the developed model, which was then implemented in a HIL system and connected to the Transmission Control Unit (TCU. Several tests have been performed on the HIL simulator, to verify the TCU performance: electrical failure tests on sensors and actuators, hydraulic and mechanical failure tests on hydraulic valves, clutches and synchronizers, and application tests comprehending all the main features of the control actions performed by the TCU. Being based on physical laws, in every condition the model simulates a plausible reaction of the system. A test automation procedure has finally been developed to permit the execution of a pattern of tests without the interaction of the user; perfectly repeatable tests can be performed for non-regression verification, allowing the testing of new software releases in fully automatic mode.

Dynamic information architecture system (DIAS) : multiple model simulation management.

Energy Technology Data Exchange (ETDEWEB)

Simunich, K. L.; Sydelko, P.; Dolph, J.; Christiansen, J.

2002-05-13

Dynamic Information Architecture System (DIAS) is a flexible, extensible, object-based framework for developing and maintaining complex multidisciplinary simulations of a wide variety of application contexts. The modeling domain of a specific DIAS-based simulation is determined by (1) software Entity (domain-specific) objects that represent the real-world entities that comprise the problem space (atmosphere, watershed, human), and (2) simulation models and other data processing applications that express the dynamic behaviors of the domain entities. In DIAS, models communicate only with Entity objects, never with each other. Each Entity object has a number of Parameter and Aspect (of behavior) objects associated with it. The Parameter objects contain the state properties of the Entity object. The Aspect objects represent the behaviors of the Entity object and how it interacts with other objects. DIAS extends the ''Object'' paradigm by abstraction of the object's dynamic behaviors, separating the ''WHAT'' from the ''HOW.'' DIAS object class definitions contain an abstract description of the various aspects of the object's behavior (the WHAT), but no implementation details (the HOW). Separate DIAS models/applications carry the implementation of object behaviors (the HOW). Any model deemed appropriate, including existing legacy-type models written in other languages, can drive entity object behavior. The DIAS design promotes plug-and-play of alternative models, with minimal recoding of existing applications. The DIAS Context Builder object builds a constructs or scenario for the simulation, based on developer specification and user inputs. Because DIAS is a discrete event simulation system, there is a Simulation Manager object with which all events are processed. Any class that registers to receive events must implement an event handler (method) to process the event during execution. Event handlers

On microscopic simulations of systems with model chemical reactions

International Nuclear Information System (INIS)

Gorecki, J.; Gorecka, J.N.

1998-01-01

Large scale computer simulations of model chemical systems play the role of idealized experiments in which theories may be tested. In this paper we present two applications of microscopic simulations based on the reactive hard sphere model. We investigate the influence of internal fluctuations on an oscillating chemical system and observe how they modify the phase portrait of it. Another application, we consider, is concerned with the propagation of a chemical wave front associated with a thermally activated reaction. It is shown that the nonequilibrium effects increase the front velocity if compared with the velocity of the front generated by a nonactivated process characterized by the same rate constant. (author)

Dynamic wind turbine models in power system simulation tool

DEFF Research Database (Denmark)

Hansen, Anca D.; Iov, Florin; Sørensen, Poul

, connection of the wind turbine at different types of grid and storage systems. Different control strategies have been developed and implemented for these wind turbine concepts, their performance in normal or fault operation being assessed and discussed by means of simulations. The described control......This report presents a collection of models and control strategies developed and implemented in the power system simulation tool PowerFactory DIgSILENT for different wind turbine concepts. It is the second edition of Risø-R-1400(EN) and it gathers and describes a whole wind turbine model database...... of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The report provides thus a description of the wind turbines modelling, both at a component level and at a system level. The report contains both the description of DIgSILENT built...

Meta-stochastic simulation of biochemical models for systems and synthetic biology.

Science.gov (United States)

Sanassy, Daven; Widera, Paweł; Krasnogor, Natalio

2015-01-16

Stochastic simulation algorithms (SSAs) are used to trace realistic trajectories of biochemical systems at low species concentrations. As the complexity of modeled biosystems increases, it is important to select the best performing SSA. Numerous improvements to SSAs have been introduced but they each only tend to apply to a certain class of models. This makes it difficult for a systems or synthetic biologist to decide which algorithm to employ when confronted with a new model that requires simulation. In this paper, we demonstrate that it is possible to determine which algorithm is best suited to simulate a particular model and that this can be predicted a priori to algorithm execution. We present a Web based tool ssapredict that allows scientists to upload a biochemical model and obtain a prediction of the best performing SSA. Furthermore, ssapredict gives the user the option to download our high performance simulator ngss preconfigured to perform the simulation of the queried biochemical model with the predicted fastest algorithm as the simulation engine. The ssapredict Web application is available at http://ssapredict.ico2s.org. It is free software and its source code is distributed under the terms of the GNU Affero General Public License.

Real-time modelling of a ventilation system for a power plant simulator

International Nuclear Information System (INIS)

Kocher, P.; Welfonder, E.

1992-01-01

This paper describes how to simulate in real-time the ventilation system of a nuclear power plant. The simulation is made under difficult computing time conditions. The ventilation system program is part of a simulator which simulates the whole nuclear power plant process in realtime. Therefore the ventilation system is split up into several smaller units. For each of these process units a real-time module has been developed, being as simple as possible but nevertheless coming close enough to the real dynamic behaviour. After that the simple real-time modules are linked together to form the total dynamic model ''ventilation system''. The continuous dynamic model developed is numerically integrated by the Euler method. The stability of this explicit method is maintained by special modelling measures such as the increasing of too low flow resistances or the limitation of too high gain factors. At the end of the paper some curves, recorded at the simulator, illustrate the behaviour of the ventilation system in the case of an accident. (author)

Simulation of personnel control systems with the Insider Safeguards Effectiveness Model (ISEM)

International Nuclear Information System (INIS)

Boozer, D.D.; Engi, D.

1977-04-01

Nuclear safeguards systems are being designed to prevent theft or sabotage of radioactive material by persons employed in nuclear facilities. As incidents of terrorism have increased, the need for more advanced safeguards systems has been recognized. Dynamic simulation models have been found useful in determining relative safeguards system effectiveness. A simulation model which treats certain aspects of the insider problem is the Insider Safeguards Effectiveness Model (ISEM). This report describes the model, discusses its role in analysis and design of safeguards systems, and explains the use of the model in conjunction with other models used for safeguards system design. Effectiveness results and sensitivities to safeguard system parameter variations are reported, and a comprehensive example of ISEM use for a hypothetical facility is given

Simulation of personnel control systems with the Insider Safeguards Effectiveness Model (ISEM)

Energy Technology Data Exchange (ETDEWEB)

Boozer, D.D.; Engi, D.

1977-04-01

Nuclear safeguards systems are being designed to prevent theft or sabotage of radioactive material by persons employed in nuclear facilities. As incidents of terrorism have increased, the need for more advanced safeguards systems has been recognized. Dynamic simulation models have been found useful in determining relative safeguards system effectiveness. A simulation model which treats certain aspects of the insider problem is the Insider Safeguards Effectiveness Model (ISEM). This report describes the model, discusses its role in analysis and design of safeguards systems, and explains the use of the model in conjunction with other models used for safeguards system design. Effectiveness results and sensitivities to safeguard system parameter variations are reported, and a comprehensive example of ISEM use for a hypothetical facility is given.

A novel approach for modelling complex maintenance systems using discrete event simulation

International Nuclear Information System (INIS)

Alrabghi, Abdullah; Tiwari, Ashutosh

2016-01-01

Existing approaches for modelling maintenance rely on oversimplified assumptions which prevent them from reflecting the complexity found in industrial systems. In this paper, we propose a novel approach that enables the modelling of non-identical multi-unit systems without restrictive assumptions on the number of units or their maintenance characteristics. Modelling complex interactions between maintenance strategies and their effects on assets in the system is achieved by accessing event queues in Discrete Event Simulation (DES). The approach utilises the wide success DES has achieved in manufacturing by allowing integration with models that are closely related to maintenance such as production and spare parts systems. Additional advantages of using DES include rapid modelling and visual interactive simulation. The proposed approach is demonstrated in a simulation based optimisation study of a published case. The current research is one of the first to optimise maintenance strategies simultaneously with their parameters while considering production dynamics and spare parts management. The findings of this research provide insights for non-conflicting objectives in maintenance systems. In addition, the proposed approach can be used to facilitate the simulation and optimisation of industrial maintenance systems. - Highlights: • This research is one of the first to optimise maintenance strategies simultaneously. • New insights for non-conflicting objectives in maintenance systems. • The approach can be used to optimise industrial maintenance systems.

Integrated building and system simulation using run-time coupled distributed models

NARCIS (Netherlands)

Trcka, M.; Hensen, J.L.M.; Wijsman, A.J.T.M.

2006-01-01

In modeling and simulation of real building and heating, ventilating, and air-conditioning (HVAC) system configurations, it is frequently found that certain parts can be represented in one simulation software, while models for other parts of the configuration are only available in other software.

Dynamic Modeling and Simulation of an Underactuated System

International Nuclear Information System (INIS)

Duarte Madrid, Juan Libardo; Querubín, E González; Henao, P A Ospina

2017-01-01

In this paper, is used the Lagrangian classical mechanics for modeling the dynamics of an underactuated system, specifically a rotary inverted pendulum that will have two equations of motion. A basic design of the system is proposed in SOLIDWORKS 3D CAD software, which based on the material and dimensions of the model provides some physical variables necessary for modeling. In order to verify the results obtained, a comparison the CAD model simulated in the environment SimMechanics of MATLAB software with the mathematical model who was consisting of Euler-Lagrange’s equations implemented in Simulink MATLAB, solved with the ODE23tb method, included in the MATLAB libraries for the solution of systems of equations of the type and order obtained. This article also has a topological analysis of pendulum trajectories through a phase space diagram, which allows the identification of stable and unstable regions of the system. (paper)

THE MARK I BUSINESS SYSTEM SIMULATION MODEL

Science.gov (United States)

of a large-scale business simulation model as a vehicle for doing research in management controls. The major results of the program were the...development of the Mark I business simulation model and the Simulation Package (SIMPAC). SIMPAC is a method and set of programs facilitating the construction...of large simulation models. The object of this document is to describe the Mark I Corporation model, state why parts of the business were modeled as they were, and indicate the research applications of the model. (Author)

Ionospheric Simulation System for Satellite Observations and Global Assimilative Model Experiments - ISOGAME

Science.gov (United States)

Pi, Xiaoqing; Mannucci, Anthony J.; Verkhoglyadova, Olga; Stephens, Philip; Iijima, Bryron A.

2013-01-01

Modeling and imaging the Earth's ionosphere as well as understanding its structures, inhomogeneities, and disturbances is a key part of NASA's Heliophysics Directorate science roadmap. This invention provides a design tool for scientific missions focused on the ionosphere. It is a scientifically important and technologically challenging task to assess the impact of a new observation system quantitatively on our capability of imaging and modeling the ionosphere. This question is often raised whenever a new satellite system is proposed, a new type of data is emerging, or a new modeling technique is developed. The proposed constellation would be part of a new observation system with more low-Earth orbiters tracking more radio occultation signals broadcast by Global Navigation Satellite System (GNSS) than those offered by the current GPS and COSMIC observation system. A simulation system was developed to fulfill this task. The system is composed of a suite of software that combines the Global Assimilative Ionospheric Model (GAIM) including first-principles and empirical ionospheric models, a multiple- dipole geomagnetic field model, data assimilation modules, observation simulator, visualization software, and orbit design, simulation, and optimization software.

Performance modelling and simulation of an absorption solar cooling system for Malaysia

International Nuclear Information System (INIS)

Assilzadeh, F.; Ali, Y.; Kamaruzzaman Sopian

2006-01-01

Solar radiation contains huge amounts of energy and is required for almost all the natural processes on earth. Solar-powered air-conditioning has many advantages when compared to normal electricity system. This paper presents a solar cooling system that has been designed for Malaysia and other tropical regions using evacuated tube solar collector and LiBr absorption system. A modelling and simulation of absorption solar cooling system is modeled in Transient System Simulation (TRNSYS) environment. The typical meteorological year file containing the weather parameters is used to simulate the system. Then a system optimization is carried out in order to select the appropriate type of collector, the optimum size of storage tank, the optimum collector slope and area and the optimum thermostat setting of the auxiliary boiler

Package Flow Model and its fuzzy implementation for simulating nuclear reactor system dynamics

International Nuclear Information System (INIS)

Matsuoka, Hiroshi; Ishiguro, Misako.

1996-01-01

A simple intuitive simulation model, which we call 'Package Flow Model', has been developed to evaluate physical processes in nuclear reactor system from a macroscopic point of view. In the previous paper, we showed the physical process of each energy generation and transfer stage in a PWR could be modeled by PFM, and its dynamics could be approximately simulated by fuzzy implementation. In this paper, a PFMs network approach for a total PWR system simulation is proposed and some transients of nuclear ship 'MUTSU' reactor system are evaluated. The simulated results are consistent with those from Nuclear Ship Engineering Simulation System developed by JAERI. Furthermore, a visual representation method is proposed to intuitively capture the profile of fuel safety transient. Using the PFMs network, we can handily calculate the transient phenomena of the system even by a notebook-type personal computer. In addition, we can easily interpret the results of calculation surveying a small number of parameters. (author)

Modelling and Simulation of a Synchronous Machine with Power Electronic Systems

DEFF Research Database (Denmark)

Chen, Zhe; Blaabjerg, Frede

2005-01-01

is modelled in SIMULINK as well. The resulting model can more accurately represent non-idea situations such as non-symmetrical parameters of the electrical machines and unbalance conditions. The model may be used for both steady state and large-signal dynamic analysis. This is particularly useful......This paper reports the modeling and simulation of a synchronous machine with a power electronic interface in direct phase model. The implementation of a direct phase model of synchronous machines in MATLAB/SIMULINK is presented .The power electronic system associated with the synchronous machine...... in the systems where a detailed study is needed in order to assess the overall system stability. Simulation studies are performed under various operation conditions. It is shown that the developed model could be used for studies of various applications of synchronous machines such as in renewable and DG...

Theoretical Models of Protostellar Binary and Multiple Systems with AMR Simulations

Science.gov (United States)

Matsumoto, Tomoaki; Tokuda, Kazuki; Onishi, Toshikazu; Inutsuka, Shu-ichiro; Saigo, Kazuya; Takakuwa, Shigehisa

2017-05-01

We present theoretical models for protostellar binary and multiple systems based on the high-resolution numerical simulation with an adaptive mesh refinement (AMR) code, SFUMATO. The recent ALMA observations have revealed early phases of the binary and multiple star formation with high spatial resolutions. These observations should be compared with theoretical models with high spatial resolutions. We present two theoretical models for (1) a high density molecular cloud core, MC27/L1521F, and (2) a protobinary system, L1551 NE. For the model for MC27, we performed numerical simulations for gravitational collapse of a turbulent cloud core. The cloud core exhibits fragmentation during the collapse, and dynamical interaction between the fragments produces an arc-like structure, which is one of the prominent structures observed by ALMA. For the model for L1551 NE, we performed numerical simulations of gas accretion onto protobinary. The simulations exhibit asymmetry of a circumbinary disk. Such asymmetry has been also observed by ALMA in the circumbinary disk of L1551 NE.

A web-based, collaborative modeling, simulation, and parallel computing environment for electromechanical systems

Directory of Open Access Journals (Sweden)

Xiaoliang Yin

2015-03-01

Full Text Available Complex electromechanical system is usually composed of multiple components from different domains, including mechanical, electronic, hydraulic, control, and so on. Modeling and simulation for electromechanical system on a unified platform is one of the research hotspots in system engineering at present. It is also the development trend of the design for complex electromechanical system. The unified modeling techniques and tools based on Modelica language provide a satisfactory solution. To meet with the requirements of collaborative modeling, simulation, and parallel computing for complex electromechanical systems based on Modelica, a general web-based modeling and simulation prototype environment, namely, WebMWorks, is designed and implemented. Based on the rich Internet application technologies, an interactive graphic user interface for modeling and post-processing on web browser was implemented; with the collaborative design module, the environment supports top-down, concurrent modeling and team cooperation; additionally, service-oriented architecture–based architecture was applied to supply compiling and solving services which run on cloud-like servers, so the environment can manage and dispatch large-scale simulation tasks in parallel on multiple computing servers simultaneously. An engineering application about pure electric vehicle is tested on WebMWorks. The results of simulation and parametric experiment demonstrate that the tested web-based environment can effectively shorten the design cycle of the complex electromechanical system.

A geographic information system-based 3D city estate modeling and simulation system

Science.gov (United States)

Chong, Xiaoli; Li, Sha

2015-12-01

This paper introduces a 3D city simulation system which is based on geographic information system (GIS), covering all commercial housings of the city. A regional- scale, GIS-based approach is used to capture, describe, and track the geographical attributes of each house in the city. A sorting algorithm of "Benchmark + Parity Rate" is developed to cluster houses with similar spatial and construction attributes. This system is applicable for digital city modeling, city planning, housing evaluation, housing monitoring, and visualizing housing transaction. Finally, taking Jingtian area of Shenzhen as an example, the each unit of 35,997 houses in the area could be displayed, tagged, and easily tracked by the GIS-based city modeling and simulation system. The match market real conditions well and can be provided to house buyers as reference.

Modeling and simulation for process and safeguards system design

International Nuclear Information System (INIS)

Gutmacher, R.G.; Kern, E.A.; Duncan, D.R.; Benecke, M.W.

1983-01-01

A computer modeling and simulation approach that meets the needs of both the process and safeguards system designers is described. The results have been useful to Westinghouse Hanford Company process designers in optimizing the process scenario and operating scheme of the Secure Automated Fabrication line. The combined process/measurements model will serve as the basis for design of the safeguards system. Integration of the process design and the safeguards system design should result in a smoothly operating process that is easier to safeguard

COSMOS: A System-Level Modelling and Simulation Framework for Coprocessor-Coupled Reconfigurable Systems

DEFF Research Database (Denmark)

Wu, Kehuai; Madsen, Jan

2007-01-01

and resource management, and iii) present a SystemC based framework to model and simulate coprocessor-coupled reconfigurable systems. We illustrate how COSMOS may be used to capture the dynamic behavior of such systems and emphasize the need for capturing the system aspects of such systems in order to deal...

Simulation modelling of fynbos ecosystems: Systems analysis and conceptual models

CSIR Research Space (South Africa)

Kruger, FJ

1985-03-01

Full Text Available -animal interactions. An additional two models, which expand aspects of the FYNBOS model, are described: a model for simulating canopy processes; and a Fire Recovery Simulator. The canopy process model will simulate ecophysiological processes in more detail than FYNBOS...

Modeling and simulation of CANDU reactor and its regulating system

Science.gov (United States)

Javidnia, Hooman

Analytical computer codes are indispensable tools in design, optimization, and control of nuclear power plants. Numerous codes have been developed to perform different types of analyses related to the nuclear power plants. A large number of these codes are designed to perform safety analyses. In the context of safety analyses, the control system is often neglected. Although there are good reasons for such a decision, that does not mean that the study of control systems in the nuclear power plants should be neglected altogether. In this thesis, a proof of concept code is developed as a tool that can be used in the design. optimization. and operation stages of the control system. The main objective in the design of this computer code is providing a tool that is easy to use by its target audience and is capable of producing high fidelity results that can be trusted to design the control system and optimize its performance. Since the overall plant control system covers a very wide range of processes, in this thesis the focus has been on one particular module of the the overall plant control system, namely, the reactor regulating system. The center of the reactor regulating system is the CANDU reactor. A nodal model for the reactor is used to represent the spatial neutronic kinetics of the core. The nodal model produces better results compared to the point kinetics model which is often used in the design and analysis of control system for nuclear reactors. The model can capture the spatial effects to some extent. although it is not as detailed as the finite difference methods. The criteria for choosing a nodal model of the core are: (1) the model should provide more detail than point kinetics and capture spatial effects, (2) it should not be too complex or overly detailed to slow down the simulation and provide details that are extraneous or unnecessary for a control engineer. Other than the reactor itself, there are auxiliary models that describe dynamics of different

SIMULATION MODEL FOR DESIGN SUPPORT OF INFOCOMM REDUNDANT SYSTEMS

Directory of Open Access Journals (Sweden)

V. A. Bogatyrev

2016-09-01

Full Text Available Subject of Research. The paper deals with the effectiveness of multipath transfer of request copies through the network and their redundant service without the use of laborious analytical modeling. The model and support tools for the design of highly reliable distributed systems based on simulation modeling have been created. Method. The effectiveness of many variants of service organization and delivery through the network to the query servers is formed and analyzed. Options for providing redundant service and delivery via the network to the servers of request copies are also considered. The choice of variants for the distribution and service of requests is carried out taking into account the criticality of queries to the time of their stay in the system. The request is considered successful if at least one of its copies is accurately delivered to the working server, ready to service the request received through a network, if it is fulfilled in the set time. Efficiency analysis of the redundant transmission and service of requests is based on the model built in AnyLogic 7 simulation environment. Main Results. Simulation experiments based on the proposed models have shown the effectiveness of redundant transmission of copies of queries (packets to the servers in the cluster through multiple paths with redundant service of request copies by a group of servers in the cluster. It is shown that this solution allows increasing the probability of exact execution of at least one copy of the request within the required time. We have carried out efficiency evaluation of destruction of outdated request copies in the queues of network nodes and the cluster. We have analyzed options for network implementation of multipath transfer of request copies to the servers in the cluster over disjoint paths, possibly different according to the number of their constituent nodes. Practical Relevance. The proposed simulation models can be used when selecting the optimal

Modelling and Simulation of Volume Controlled Mechanical Ventilation System

Directory of Open Access Journals (Sweden)

Yan Shi

2014-01-01

Full Text Available Volume controlled mechanical ventilation system is a typical time-delay system, which is applied to ventilate patients who cannot breathe adequately on their own. To illustrate the influences of key parameters of the ventilator on the dynamics of the ventilated respiratory system, this paper firstly derived a new mathematical model of the ventilation system; secondly, simulation and experimental results are compared to verify the mathematical model; lastly, the influences of key parameters of ventilator on the dynamics of the ventilated respiratory system are carried out. This study can be helpful in the VCV ventilation treatment and respiratory diagnostics.

Development of new methods for the modeling of technical systems and result evaluation for reactor safety simulation codes. Modeling, simulation models; Entwicklung neuer Methoden zur Modellierung technischer Systeme und zur Ergebnisauswertung fuer Simulationsprogramme der Reaktorsicherheit. Modellierung, Simulationsprogramme

Energy Technology Data Exchange (ETDEWEB)

Cester, Francesco; Deitenbeck, Helmuth; Kuentzel, Matthias; Scheuer, Josef; Voggenberger, Thomas

2015-04-15

The overall objective of the project is to develop a general simulation environment for program systems used in reactor safety analysis. The simulation environment provides methods for graphical modeling and evaluation of results for the simulation models. The terms of graphical modeling and evaluation of results summarize computerized methods of pre- and postprocessing for the simulation models, which can assist the user in the execution of the simulation steps. The methods comprise CAD (''Computer Aided Design'') based input tools, interactive user interfaces for the execution of the simulation and the graphical representation and visualization of the simulation results. A particular focus was set on the requirements of the system code ATHLET. A CAD tool was developed that allows the specification of 3D geometry of the plant components and the discretization with a simulation grid. The system provides inter-faces to generate the input data of the codes and to export the data for the visualization software. The CAD system was applied for the modeling of a cooling circuit and reactor pressure vessel of a PWR. For the modeling of complex systems with many components, a general purpose graphical network editor was adapted and expanded. The editor is able to simulate networks with complex topology graphically by suitable building blocks. The network editor has been enhanced and adapted to the modeling of balance of plant and thermal fluid systems in ATHLET. For the visual display of the simulation results in the local context of the 3D geometry and the simulation grid, the open source program ParaView is applied, which is widely used for 3D visualization of field data, offering multiple options for displaying and ana-lyzing the data. New methods were developed, that allow the necessary conversion of the results of the reactor safety codes and the data of the CAD models. The trans-formed data may then be imported into ParaView and visualized. The

Influence of Various Irradiance Models and Their Combination on Simulation Results of Photovoltaic Systems

Directory of Open Access Journals (Sweden)

Martin Hofmann

2017-09-01

Full Text Available We analyze the output of various state-of-the-art irradiance models for photovoltaic systems. The models include two sun position algorithms, three types of input data time series, nine diffuse fraction models and five transposition models (for tilted surfaces, resulting in 270 different model chains for the photovoltaic (PV system simulation. These model chains are applied to 30 locations worldwide and three different module tracking types, totaling in 24,300 simulations. We show that the simulated PV yearly energy output varies between −5% and +8% for fixed mounted PV modules and between −26% and +14% for modules with two-axis tracking. Model quality varies strongly between locations; sun position algorithms have negligible influence on the simulation results; diffuse fraction models add a lot of variability; and transposition models feature the strongest influence on the simulation results. To highlight the importance of irradiance with high temporal resolution, we present an analysis of the influence of input temporal resolution and simulation models on the inverter clipping losses at varying PV system sizing factors for Lindenberg, Germany. Irradiance in one-minute resolution is essential for accurately calculating inverter clipping losses.

NCS--a software for visual modeling and simulation of PWR nuclear power plant control system

International Nuclear Information System (INIS)

Cui Zhenhua

1998-12-01

The modeling and simulation of nuclear power plant control system has been investigated. Some mathematical models for rapid and accurate simulation are derived, including core models, pressurizer model, steam generator model, etc. Several numerical methods such as Runge-Kutta Method and Treanor Method are adopted to solve the above system models. In order to model the control system conveniently, a block diagram-oriented visual modeling platform is designed. And the Discrete Similarity Method is used to calculate the control system models. A corresponding simulating software, NCS, is developed for researching on the control systems of commercial nuclear power plant. And some satisfactory results are obtained. The research works will be of referential and applying value to design and analysis of nuclear power plant control system

System dynamics modelling and simulating the effects of intellectual capital on economic growth

Directory of Open Access Journals (Sweden)

Ivona Milić Beran

2015-10-01

Full Text Available System dynamics modelling is one of the best scientific methods for modelling complex, nonlinear natural, economic and technical system dynamics as it enables both monitoring and assessment of the effects of intellectual capital on economic growth. Intellectual capital is defined as “the ability to transform knowledge and intangible assets into resources to create wealth for a company and a country.” Transformation of knowledge is crucial. Knowledge increases a country’s wealth only if its importance is recognized and applied differently from existing work practices. The aim of this paper is to show the efficiency of modelling system dynamics and simulating the effects of intellectual capital on economic growth. A computer simulation provided a mathematical model, providing practical insight into the dynamic behavior of the observed system, i.e. the analysis of economic growth and observation of mutual correlation between individual parameters. The results of the simulation are presented in graphical form. The dynamic model of the effects of intellectual capital on Croatia’s economic growth has been verified by comparing simulation results with existing data on economic growth.

MATLAB/Simulink Pulse-Echo Ultrasound System Simulator Based on Experimentally Validated Models.

Science.gov (United States)

Kim, Taehoon; Shin, Sangmin; Lee, Hyongmin; Lee, Hyunsook; Kim, Heewon; Shin, Eunhee; Kim, Suhwan

2016-02-01

A flexible clinical ultrasound system must operate with different transducers, which have characteristic impulse responses and widely varying impedances. The impulse response determines the shape of the high-voltage pulse that is transmitted and the specifications of the front-end electronics that receive the echo; the impedance determines the specification of the matching network through which the transducer is connected. System-level optimization of these subsystems requires accurate modeling of pulse-echo (two-way) response, which in turn demands a unified simulation of the ultrasonics and electronics. In this paper, this is realized by combining MATLAB/Simulink models of the high-voltage transmitter, the transmission interface, the acoustic subsystem which includes wave propagation and reflection, the receiving interface, and the front-end receiver. To demonstrate the effectiveness of our simulator, the models are experimentally validated by comparing the simulation results with the measured data from a commercial ultrasound system. This simulator could be used to quickly provide system-level feedback for an optimized tuning of electronic design parameters.

Genetic fuzzy system modeling and simulation of vascular behaviour

DEFF Research Database (Denmark)

Tang, Jiaowei; Boonen, Harrie C.M.

Background: The purpose of our project is to identify the rule sets and their interaction within the framework of cardiovascular function. By an iterative process of computational simulation and experimental work, we strive to mimic the physiological basis for cardiovascular adaptive changes in c...... the pressure change of different blood vessels. Conclusion: Genetic fuzzy system is one of potential modeling methods in modeling and simulation of vascular behavior.......Background: The purpose of our project is to identify the rule sets and their interaction within the framework of cardiovascular function. By an iterative process of computational simulation and experimental work, we strive to mimic the physiological basis for cardiovascular adaptive changes...... in cardiovascular disease and ultimately improve pharmacotherapy. For this purpose, novel computational approaches incorporating adaptive properties, auto-regulatory control and rule sets will be assessed, properties that are commonly lacking in deterministic models based on differential equations. We hypothesize...

A dynamic model of the reactor coolant system flow for KMRR plant simulation

International Nuclear Information System (INIS)

Rhee, B.W.; Noh, T.W.; Park, C.; Sim, B.S.; Oh, S.K.

1990-01-01

To support computer simulation studies for reactor control system design and performance evaluation, a dynamic model of the reactor coolant system (RCS) and reflector cooling system has been developed. This model is composed of the reactor coolant loop momentum equation, RCS pump dynamic equation, RCS pump characteristic equation, and the energy equation for the coolant inside the various components and piping. The model is versatile enough to simulate the normal steady-state conditions as well as most of the anticipated flow transients without pipe rupture. This model has been successfully implemented as the plant simulation code KMRRSIM for the Korea Multi-purpose Research Reactor and is now under extensive validation testing. The initial stage of validation has been comparison of its result with that of already validated, more detailed reactor system transient codes such as RELAP5. The results, as compared to the predictions by RELAP5 simulation, have been generally found to be very encouraging and the model is judged to be accurate enough to fulfill its intended purpose. However, this model will continue to be validated against other plant's data and eventually will be assessed by test data from KMRR

The use of physical model simulation to emulate an AGV material handling system

International Nuclear Information System (INIS)

Hurley, R.G.; Coffman, P.E.; Dixon, J.R.; Walacavage, J.G.

1987-01-01

This paper describes an application of physical modeling to the simulation of a prototype AGV (Automatic Guided Vehicle) material handling system. Physical modeling is the study of complex automated manufacturing and material handling systems through the use of small scale components controlled by mini and/or microcomputers. By modeling the mechanical operations of the proposed AGV material handling system, it was determined that control algorithms and AGV dispatch rules could be developed and evaluated. This paper presents a brief explanation of physical modeling as a simulation tool and addresses in detail the development of the control algorithm, dispatching rules, and a prototype physical model of a flexible machining system

Convective Systems Over the Japan Sea: Cloud-Resolving Model Simulations

Science.gov (United States)

Tao, Wei-Kuo; Yoshizaki, Masanori; Shie, Chung-Lin; Kato, Teryuki

2002-01-01

Wintertime observations of MCSs (Mesoscale Convective Systems) over the Sea of Japan - 2001 (WMO-01) were collected from January 12 to February 1, 2001. One of the major objectives is to better understand and forecast snow systems and accompanying disturbances and the associated key physical processes involved in the formation and development of these disturbances. Multiple observation platforms (e.g., upper-air soundings, Doppler radar, wind profilers, radiometers, etc.) during WMO-01 provided a first attempt at investigating the detailed characteristics of convective storms and air pattern changes associated with winter storms over the Sea of Japan region. WMO-01 also provided estimates of the apparent heat source (Q1) and apparent moisture sink (Q2). The vertical integrals of Q1 and Q2 are equal to the surface precipitation rates. The horizontal and vertical adjective components of Q1 and Q2 can be used as large-scale forcing for the Cloud Resolving Models (CRMs). The Goddard Cumulus Ensemble (GCE) model is a CRM (typically run with a 1-km grid size). The GCE model has sophisticated microphysics and allows explicit interactions between clouds, radiation, and surface processes. It will be used to understand and quantify precipitation processes associated with wintertime convective systems over the Sea of Japan (using data collected during the WMO-01). This is the first cloud-resolving model used to simulate precipitation processes in this particular region. The GCE model-simulated WMO-01 results will also be compared to other GCE model-simulated weather systems that developed during other field campaigns (i.e., South China Sea, west Pacific warm pool region, eastern Atlantic region and central USA).

Dynamic modeling and simulation of the superconducting super collider cryogenic helium system

International Nuclear Information System (INIS)

Hartzog, D.G.; Fox, V.G.; Mathias, P.M.; Nahmias, D.; McAshan, M.; Carcagno, R.

1989-01-01

To study the operation of the Superconducting Super Collider (SSC) cryogenic system during transient operating conditions, they have developed and programmed in FORTRAN, a time-dependent, nonlinear, homogeneous, lumped-parameter simulation model of the SSC cryogenic system. This dynamic simulator has a modular structure so that process flowsheet modifications can be easily accommodated with minimal recoding. It uses the LSODES integration package to advance the solution in time. For helium properties it uses Air Products implementation of the standard thermodynamic model developed by the NBS. Two additional simplified helium thermodynamic models developed by Air Products are available as options to reduce computation time. To facilitate the interpretation of output, they have linked the simulator to the speakeasy conversational language. The authors present a flowsheet of the process simulated, and the material and energy balances used in the engineering models. They then show simulation results for three transient operating scenarios: startup of the refrigeration system from standby to full load; the loss of 4K refrigeration caused by the tripping of one of two parallel compressors in a sector; and a full-field quench of a single magnet half-cell. They discuss the response of the fluid within the cryogenic circuits during these scenarios. 14 refs., 19 figs., 2 tabs

A Calculus for Modelling, Simulating and Analysing Compartmentalized Biological Systems

DEFF Research Database (Denmark)

Mardare, Radu Iulian; Ihekwaba, Adoha

2007-01-01

A. Ihekwaba, R. Mardare. A Calculus for Modelling, Simulating and Analysing Compartmentalized Biological Systems. Case study: NFkB system. In Proc. of International Conference of Computational Methods in Sciences and Engineering (ICCMSE), American Institute of Physics, AIP Proceedings, N 2...

Semantic World Modelling and Data Management in a 4d Forest Simulation and Information System

Science.gov (United States)

Roßmann, J.; Hoppen, M.; Bücken, A.

2013-08-01

Various types of 3D simulation applications benefit from realistic forest models. They range from flight simulators for entertainment to harvester simulators for training and tree growth simulations for research and planning. Our 4D forest simulation and information system integrates the necessary methods for data extraction, modelling and management. Using modern methods of semantic world modelling, tree data can efficiently be extracted from remote sensing data. The derived forest models contain position, height, crown volume, type and diameter of each tree. This data is modelled using GML-based data models to assure compatibility and exchangeability. A flexible approach for database synchronization is used to manage the data and provide caching, persistence, a central communication hub for change distribution, and a versioning mechanism. Combining various simulation techniques and data versioning, the 4D forest simulation and information system can provide applications with "both directions" of the fourth dimension. Our paper outlines the current state, new developments, and integration of tree extraction, data modelling, and data management. It also shows several applications realized with the system.

Modeling, Design and Simulation of Stand-Alone Photovoltaic Power Systems with Battery Storage

Directory of Open Access Journals (Sweden)

Abd Essalam BADOUD

2013-06-01

Full Text Available Stand alone renewable energy based on photovoltaic systems accompanied with battery storage system are beginning to play an important role over the world to supply power to remote areas. The objective of the study reported in this paper is to elaborate and design a bond graphs model for sizing stand-alone domestic solar photovoltaic electricity systems and simulating the performance of the systems in a tropical climate. The systems modelled consist of an array of PV modules, a lead-acid battery, and a number of direct current appliances. This paper proposes the combination of lead acid battery system with a typical stand alone photovoltaic energy system under variable loads. The main activities of this work purpose to establish library graphical models for each individual component of standalone photovoltaic system. Control strategy has been considered to achieve permanent power supply to the load via photovoltaic/battery based on the power available from the sun. The complete model was simulated under two testing including sunny and cloudy conditions. Simulation of the system using Symbols software was performed and the results of simulation show the superior stable control system and high efficiency. These results have been contrasted with real measured data from a measurement campaign plant carried on electrical engineering laboratory of Grenoble using various interconnection schemes are presented.

Hybrid2 - The hybrid power system simulation model

Energy Technology Data Exchange (ETDEWEB)

Baring-Gould, E.I.; Green, H.J.; Dijk, V.A.P. van [National Renewable Energy Lab., Golden, CO (United States); Manwell, J.F. [Univ. of Massachusetts, Amherst, MA (United States)

1996-12-31

There is a large-scale need and desire for energy in remote communities, especially in the developing world; however the lack of a user friendly, flexible performance prediction model for hybrid power systems incorporating renewables hindered the analysis of hybrids as options to conventional solutions. A user friendly model was needed with the versatility to simulate the many system locations, widely varying hardware configurations, and differing control options for potential hybrid power systems. To meet these ends, researchers from the National Renewable Energy Laboratory (NREL) and the University of Massachusetts (UMass) developed the Hybrid2 software. This paper provides an overview of the capabilities, features, and functionality of the Hybrid2 code, discusses its validation and future plans. Model availability and technical support provided to Hybrid2 users are also discussed. 12 refs., 3 figs., 4 tabs.

Modeling and Simulation of Renewable Hybrid Power System using Matlab Simulink Environment

Directory of Open Access Journals (Sweden)

Cristian Dragoş Dumitru

2010-12-01

Full Text Available The paper presents the modeling of a solar-wind-hydroelectric hybrid system in Matlab/Simulink environment. The application is useful for analysis and simulation of a real hybrid solar-wind-hydroelectric system connected to a public grid. Application is built on modular architecture to facilitate easy study of each component module influence. Blocks like wind model, solar model, hydroelectric model, energy conversion and load are implemented and the results of simulation are also presented. As an example, one of the most important studies is the behavior of hybrid system which allows employing renewable and variable in time energy sources while providing a continuous supply. Application represents a useful tool in research activity and also in teaching

Fat Tail Model for Simulating Test Systems in Multiperiod Unit Commitment

Directory of Open Access Journals (Sweden)

J. A. Marmolejo

2015-01-01

Full Text Available This paper describes the use of Chambers-Mallows-Stuck method for simulating stable random variables in the generation of test systems for economic analysis in power systems. A study that focused on generating test electrical systems through fat tail model for unit commitment problem in electrical power systems is presented. Usually, the instances of test systems in Unit Commitment are generated using normal distribution, but in this work, simulations data are based on a new method. For simulating, we used three original systems to obtain the demand behavior and thermal production costs. The estimation of stable parameters for the simulation of stable random variables was based on three generally accepted methods: (a regression, (b quantiles, and (c maximum likelihood, choosing one that has the best fit of the tails of the distribution. Numerical results illustrate the applicability of the proposed method by solving several unit commitment problems.

Benchmarking Model Variants in Development of a Hardware-in-the-Loop Simulation System

Science.gov (United States)

Aretskin-Hariton, Eliot D.; Zinnecker, Alicia M.; Kratz, Jonathan L.; Culley, Dennis E.; Thomas, George L.

2016-01-01

Distributed engine control architecture presents a significant increase in complexity over traditional implementations when viewed from the perspective of system simulation and hardware design and test. Even if the overall function of the control scheme remains the same, the hardware implementation can have a significant effect on the overall system performance due to differences in the creation and flow of data between control elements. A Hardware-in-the-Loop (HIL) simulation system is under development at NASA Glenn Research Center that enables the exploration of these hardware dependent issues. The system is based on, but not limited to, the Commercial Modular Aero-Propulsion System Simulation 40k (C-MAPSS40k). This paper describes the step-by-step conversion from the self-contained baseline model to the hardware in the loop model, and the validation of each step. As the control model hardware fidelity was improved during HIL system development, benchmarking simulations were performed to verify that engine system performance characteristics remained the same. The results demonstrate the goal of the effort; the new HIL configurations have similar functionality and performance compared to the baseline C-MAPSS40k system.

Object Oriented Toolbox for Modelling and Simulation of Dynamical Systems

DEFF Research Database (Denmark)

Poulsen, Mikael Zebbelin; Wagner, Falko Jens; Thomsen, Per Grove

1998-01-01

This paper presents the results of an ongoing project, dealing with design and implementation of a simulation toolbox based on object oriented modelling techniques. The paper describes an experimental implementation of parts of such a toolbox in C++, and discusses the experiences drawn from that ...... that process. Essential to the work is the focus on simulation of complex dynamical systems, from modelling the single components/subsystems to building complete systemssuch a toolbox in C++, and discusses the experiences drawn from that process....

Model simulation of the Manasquan water-supply system in Monmouth County, New Jersey

Science.gov (United States)

Chang, Ming; Tasker, Gary D.; Nieswand, Steven

2001-01-01

Model simulation of the Manasquan Water Supply System in Monmouth County, New Jersey, was completed using historic hydrologic data to evaluate the effects of operational and withdrawal alternatives on the Manasquan reservoir and pumping system. Changes in the system operations can be simulated with the model using precipitation forecasts. The Manasquan Reservoir system model operates by using daily streamflow values, which were reconstructed from historical U.S. Geological Survey streamflow-gaging station records. The model is able to run in two modes--General Risk analysis Model (GRAM) and Position Analysis Model (POSA). The GRAM simulation procedure uses reconstructed historical streamflow records to provide probability estimates of certain events, such as reservoir storage levels declining below a specific level, when given an assumed set of operating rules and withdrawal rates. POSA can be used to forecast the likelihood of specified outcomes, such as streamflows falling below statutory passing flows, associated with a specific working plan for the water-supply system over a period of months. The user can manipulate the model and generate graphs and tables of streamflows and storage, for example. This model can be used as a management tool to facilitate the development of drought warning and drought emergency rule curves and safe yield values for the water-supply system.

FEM simulation of TBC failure in a model system

Energy Technology Data Exchange (ETDEWEB)

Seiler, P; Baeker, M; Roesier, J [Institut fuer Werkstoffe (IfW), Technische Universitaet Braunschweig (Germany); Beck, T; Schweda, M, E-mail: p.seiler@tu-bs.d [Institut fuer Energieforschung/ Werkstoffstruktur und -Eigenschaften (IEF 2), Forschungszentrum Juelich (Germany)

2010-07-01

In order to study the behavior of the complex failure mechanisms in thermal barrier coatings on turbine blades, a simplified model system is used to reduce the number of system parameters. The artificial system consists of a bond-coat material (fast creeping Fecralloy or slow creeping MA956) as the substrate with a Y{sub 2}O{sub 3} partially stabilized plasma sprayed zircon oxide TBC on top and a TGO between the two layers. A 2-dimensional FEM simulation was developed to calculate the growth stress inside the simplified coating system. The simulation permits the study of failure mechanisms by identifying compression and tension areas which are established by the growth of the oxide layer. This provides an insight into the possible crack paths in the coating and it allows to draw conclusions for optimizing real thermal barrier coating systems.

A computational platform for modeling and simulation of pipeline georeferencing systems

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, A.G.; Pellanda, P.C.; Gois, J.A. [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Roquette, P.; Pinto, M.; Durao, R. [Instituto de Pesquisas da Marinha (IPqM), Rio de Janeiro, RJ (Brazil); Silva, M.S.V.; Martins, W.F.; Camillo, L.M.; Sacsa, R.P.; Madeira, B. [Ministerio de Ciencia e Tecnologia (CT-PETRO2006MCT), Brasilia, DF (Brazil). Financiadora de Estudos e Projetos (FINEP). Plano Nacional de Ciencia e Tecnologia do Setor Petroleo e Gas Natural

2009-07-01

This work presents a computational platform for modeling and simulation of pipeline geo referencing systems, which was developed based on typical pipeline characteristics, on the dynamical modeling of Pipeline Inspection Gauge (PIG) and on the analysis and implementation of an inertial navigation algorithm. The software environment of PIG trajectory simulation and navigation allows the user, through a friendly interface, to carry-out evaluation tests of the inertial navigation system under different scenarios. Therefore, it is possible to define the required specifications of the pipeline geo referencing system components, such as: required precision of inertial sensors, characteristics of the navigation auxiliary system (GPS surveyed control points, odometers etc.), pipeline construction information to be considered in order to improve the trajectory estimation precision, and the signal processing techniques more suitable for the treatment of inertial sensors data. The simulation results are analyzed through the evaluation of several performance metrics usually considered in inertial navigation applications, and 2D and 3D plots of trajectory estimation error and of recovered trajectory in the three coordinates are made available to the user. This paper presents the simulation platform and its constituting modules and defines their functional characteristics and interrelationships.(author)

Dynamic wind turbine models in power system simulation tool DIgSILENT

OpenAIRE

Hansen, A.D.; Jauch, C.; Sørensen, Poul Ejnar; Iov, F.; Blaabjerg, F.

2004-01-01

The present report describes the dynamic wind turbine models implemented in the power system simulation tool DIgSILENT (Version 12.0). The developed models are a part of the results of a national research project, whose overall objective is to create amodel database in different simulation tools. This model database should be able to support the analysis of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The repo...

Modeling and simulation of M/M/c queuing pharmacy system with adjustable parameters

Science.gov (United States)

Rashida, A. R.; Fadzli, Mohammad; Ibrahim, Safwati; Goh, Siti Rohana

2016-02-01

This paper studies a discrete event simulation (DES) as a computer based modelling that imitates a real system of pharmacy unit. M/M/c queuing theo is used to model and analyse the characteristic of queuing system at the pharmacy unit of Hospital Tuanku Fauziah, Kangar in Perlis, Malaysia. The input of this model is based on statistical data collected for 20 working days in June 2014. Currently, patient waiting time of pharmacy unit is more than 15 minutes. The actual operation of the pharmacy unit is a mixed queuing server with M/M/2 queuing model where the pharmacist is referred as the server parameters. DES approach and ProModel simulation software is used to simulate the queuing model and to propose the improvement for queuing system at this pharmacy system. Waiting time for each server is analysed and found out that Counter 3 and 4 has the highest waiting time which is 16.98 and 16.73 minutes. Three scenarios; M/M/3, M/M/4 and M/M/5 are simulated and waiting time for actual queuing model and experimental queuing model are compared. The simulation results show that by adding the server (pharmacist), it will reduce patient waiting time to a reasonable improvement. Almost 50% average patient waiting time is reduced when one pharmacist is added to the counter. However, it is not necessary to fully utilize all counters because eventhough M/M/4 and M/M/5 produced more reduction in patient waiting time, but it is ineffective since Counter 5 is rarely used.

Analysis of Intelligent Transportation Systems Using Model-Driven Simulations

Directory of Open Access Journals (Sweden)

Alberto Fernández-Isabel

2015-06-01

Full Text Available Intelligent Transportation Systems (ITSs integrate information, sensor, control, and communication technologies to provide transport related services. Their users range from everyday commuters to policy makers and urban planners. Given the complexity of these systems and their environment, their study in real settings is frequently unfeasible. Simulations help to address this problem, but present their own issues: there can be unintended mistakes in the transition from models to code; their platforms frequently bias modeling; and it is difficult to compare works that use different models and tools. In order to overcome these problems, this paper proposes a framework for a model-driven development of these simulations. It is based on a specific modeling language that supports the integrated specification of the multiple facets of an ITS: people, their vehicles, and the external environment; and a network of sensors and actuators conveniently arranged and distributed that operates over them. The framework works with a model editor to generate specifications compliant with that language, and a code generator to produce code from them using platform specifications. There are also guidelines to help researchers in the application of this infrastructure. A case study on advanced management of traffic lights with cameras illustrates its use.

CONFIG - Adapting qualitative modeling and discrete event simulation for design of fault management systems

Science.gov (United States)

Malin, Jane T.; Basham, Bryan D.

1989-01-01

CONFIG is a modeling and simulation tool prototype for analyzing the normal and faulty qualitative behaviors of engineered systems. Qualitative modeling and discrete-event simulation have been adapted and integrated, to support early development, during system design, of software and procedures for management of failures, especially in diagnostic expert systems. Qualitative component models are defined in terms of normal and faulty modes and processes, which are defined by invocation statements and effect statements with time delays. System models are constructed graphically by using instances of components and relations from object-oriented hierarchical model libraries. Extension and reuse of CONFIG models and analysis capabilities in hybrid rule- and model-based expert fault-management support systems are discussed.

An advanced modelling tool for simulating complex river systems.

Science.gov (United States)

Trancoso, Ana Rosa; Braunschweig, Frank; Chambel Leitão, Pedro; Obermann, Matthias; Neves, Ramiro

2009-04-01

The present paper describes MOHID River Network (MRN), a 1D hydrodynamic model for river networks as part of MOHID Water Modelling System, which is a modular system for the simulation of water bodies (hydrodynamics and water constituents). MRN is capable of simulating water quality in the aquatic and benthic phase and its development was especially focused on the reproduction of processes occurring in temporary river networks (flush events, pools formation, and transmission losses). Further, unlike many other models, it allows the quantification of settled materials at the channel bed also over periods when the river falls dry. These features are very important to secure mass conservation in highly varying flows of temporary rivers. The water quality models existing in MOHID are base on well-known ecological models, such as WASP and ERSEM, the latter allowing explicit parameterization of C, N, P, Si, and O cycles. MRN can be coupled to the basin model, MOHID Land, with computes runoff and porous media transport, allowing for the dynamic exchange of water and materials between the river and surroundings, or it can be used as a standalone model, receiving discharges at any specified nodes (ASCII files of time series with arbitrary time step). These features account for spatial gradients in precipitation which can be significant in Mediterranean-like basins. An interface has been already developed for SWAT basin model.

Dynamic wind turbine models in power system simulation tool DIgSILENT

Energy Technology Data Exchange (ETDEWEB)

Hansen, A.D.; Iov, F.; Soerensen, Poul.; Cutululis, N.; Jauch, C.; Blaabjerg, F.

2007-08-15

This report presents a collection of models and control strategies developed and implemented in the power system simulation tool PowerFactory DIgSILENT for different wind turbine concepts. It is the second edition of Risoe-R-1400(EN) and it gathers and describes a whole wind turbine model database built-op and developed during several national research projects, carried out at Risoe DTU National Laboratory for Sustainable Energy and Aalborg University, in the period 2001-2007. The overall objective of these projects was to create a wind turbine model database able to support the analysis of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The report provides thus a description of the wind turbines modelling, both at a component level and at a system level. The report contains both the description of DIgSILENT built-in models for the electrical components of a grid connected wind turbine (e.g. induction generators, power converters, transformers) and the models developed by the user, in the dynamic simulation language DSL of DIgSILENT, for the non-electrical components of the wind turbine (wind model, aerodynamic model, mechanical model). The initialisation issues on the wind turbine models into the power system simulation are also presented. The main attention in the report is drawn to the modelling at the system level of the following wind turbine concepts: (1) Fixed speed active stall wind turbine concept (2) Variable speed doubly-fed induction generator wind turbine concept (3) Variable speed multi-pole permanent magnet synchronous generator wind turbine concept These wind turbine concept models can be used and even extended for the study of different aspects, e.g. the assessment of power quality, control strategies, connection of the wind turbine at different types of grid and storage systems. Different control strategies have been developed and implemented for these wind turbine

A PC-based discrete event simulation model of the Civilian Radioactive Waste Management System

International Nuclear Information System (INIS)

Airth, G.L.; Joy, D.S.; Nehls, J.W.

1991-01-01

A System Simulation Model has been developed for the Department of Energy to simulate the movement of individual waste packages (spent fuel assemblies and fuel containers) through the Civilian Radioactive Waste Management System (CRWMS). A discrete event simulation language, GPSS/PC, which runs on an IBM/PC and operates under DOS 5.0, mathematically represents the movement and processing of radioactive waste packages through the CRWMS and the interaction of these packages with the equipment in the various facilities. This model can be used to quantify the impacts of different operating schedules, operational rules, system configurations, and equipment reliability and availability considerations on the performance of processes comprising the CRWMS and how these factors combine to determine overall system performance for the purpose of making system design decisions. The major features of the System Simulation Model are: the ability to reference characteristics of the different types of radioactive waste (age, burnup, etc.) in order to make operational and/or system design decisions, the ability to place stochastic variations on operational parameters such as processing time and equipment outages, and the ability to include a rigorous simulation of the transportation system. Output from the model includes the numbers, types, and characteristics of waste packages at selected points in the CRWMS and the extent to which various resources will be utilized in order to transport, process, and emplace the waste

Mathematical modeling and simulation of a thermal system

Science.gov (United States)

Toropoc, Mirela; Gavrila, Camelia; Frunzulica, Rodica; Toma, Petrica D.

2016-12-01

The aim of the present paper is the conception of a mathematical model and simulation of a system formed by a heatexchanger for domestic hot water preparation, a storage tank for hot water and a radiator, starting from the mathematical equations describing this system and developed using Scilab-Xcos program. The model helps to determine the evolution in time for the hot water temperature, for the return temperature in the primary circuit of the heat exchanger, for the supply temperature in the secondary circuit, the thermal power for heating and for hot water preparation to the consumer respectively. In heating systems, heat-exchangers have an important role and their performances influence the energy efficiency of the systems. In the meantime, it is very important to follow the behavior of such systems in dynamic regimes. Scilab-Xcos program can be utilized to follow the important parameters of the systems in different functioning scenarios.

A PC-based discrete event simulation model of the civilian radioactive waste management system

International Nuclear Information System (INIS)

Airth, G.L.; Joy, D.S.; Nehls, J.W.

1992-01-01

This paper discusses a System Simulation Model which has been developed for the Department of Energy to simulate the movement of individual waste packages (spent fuel assemblies and fuel containers) through the Civilian Radioactive Waste Management System (CRWMS). A discrete event simulation language, GPSS/PC, which runs on an IBM/PC and operates under DOS 5.0, mathematically represents the movement and processing of radioactive waste packages through the CRWMS and the interaction of these packages with the equipment in the various facilities. The major features of the System Simulation Model are: the ability to reference characteristics of the different types of radioactive waste (age, burnup, etc.) in order to make operational and/or system design decisions, the ability to place stochastic variations on operational parameters such as processing time and equipment outages, and the ability to include a rigorous simulation of the transportation system. Output from the model includes the numbers, types, and characteristics of waste packages at selected points in the CRWMS and the extent to which various resources will be utilized in order to transport, process, and emplace the waste

Modeling and simulating two cut-to-length harvesting systems in central Appalachian hardwoods

Science.gov (United States)

Jingxin Wang; Chris B. LeDoux; Yaoxiang Li

2003-01-01

The production rates and costs of two cut-to-length harvesting systems was simulated using a modular ground-based simulation model and stand yield data from fully stocked, second growth even aged central Appalachian hardwood forests. The two harvesters simulated were a modified John Deere 988 tracked excavator with a model RP 1600 single grip sawhead and an excavator...

Dynamic Modeling and Simulation of Deep Geothermal Electric Submersible Pumping Systems

Directory of Open Access Journals (Sweden)

Julian Kullick

2017-10-01

Full Text Available Deep geothermal energy systems employ electric submersible pumps (ESPs in order to lift geothermal fluid from the production well to the surface. However, rough downhole conditions and high flow rates impose heavy strain on the components, leading to frequent failures of the pump system. As downhole sensor data is limited and often unrealible, a detailed and dynamical model system will serve as basis for deeper understanding and analysis of the overall system behavior. Furthermore, it allows to design model-based condition monitoring and fault detection systems, and to improve controls leading to a more robust and efficient operation. In this paper, a detailed state-space model of the complete ESP system is derived, covering the electrical, mechanical and hydraulic subsystems. Based on the derived model, the start-up phase of an exemplary yet realistic ESP system in the Megawatt range—located at a setting depth of 950 m and producing geothermal fluid of 140 ∘ C temperature at a rate of 0.145 m 3 s − 1 —is simulated in MATLAB/Simulink. The simulation results show that the system reaches a stable operating point with realistic values. Furthermore, the effect of self-excitation between the filter capacitor and the motor inductor can clearly be observed. A full set of parameters is provided, allowing for direct model implementation and reproduction of the presented results.

Dynamic Modeling and Simulation on a Hybrid Power System for Electric Vehicle Applications

Directory of Open Access Journals (Sweden)

Hong-Wen He

2010-11-01

Full Text Available Hybrid power systems, formed by combining high-energy-density batteries and high-power-density ultracapacitors in appropriate ways, provide high-performance and high-efficiency power systems for electric vehicle applications. This paper first establishes dynamic models for the ultracapacitor, the battery and a passive hybrid power system, and then based on the dynamic models a comparative simulation between a battery only power system and the proposed hybrid power system was done under the UDDS (Urban Dynamometer Driving Schedule. The simulation results showed that the hybrid power system could greatly optimize and improve the efficiency of the batteries and their dynamic current was also decreased due to the participation of the ultracapacitors, which would have a good influence on batteries’ cycle life. Finally, the parameter matching for the passive hybrid power system was studied by simulation and comparisons.

Implementation of the frequency dependent line model in a real-time power system simulator

Directory of Open Access Journals (Sweden)

Reynaldo Iracheta-Cortez

2017-09-01

Full Text Available In this paper is described the implementation of the frequency-dependent line model (FD-Line in a real-time digital power system simulator. The main goal with such development is to describe a general procedure to incorporate new realistic models of power system components in modern real-time simulators based on the Electromagnetic Transients Program (EMTP. In this procedure are described, firstly, the steps to obtain the time domain solution of the differential equations that models the electromagnetic behavior in multi-phase transmission lines with frequency dependent parameters. After, the algorithmic solution of the FD-Line model is implemented in Simulink environment, through an S-function programmed in C language, for running off-line simulations of electromagnetic transients. This implementation allows the free assembling of the FD Line model with any element of the Power System Blockset library and also, it can be used to build any network topology. The main advantage of having a power network built in Simulink is that can be executed in real-time by means of the commercial eMEGAsim simulator. Finally, several simulation cases are presented to validate the accuracy and the real-time performance of the FD-Line model.

Simulation modeling and analysis with Arena

CERN Document Server

Altiok, Tayfur

2007-01-01

Simulation Modeling and Analysis with Arena is a highly readable textbook which treats the essentials of the Monte Carlo discrete-event simulation methodology, and does so in the context of a popular Arena simulation environment.” It treats simulation modeling as an in-vitro laboratory that facilitates the understanding of complex systems and experimentation with what-if scenarios in order to estimate their performance metrics. The book contains chapters on the simulation modeling methodology and the underpinnings of discrete-event systems, as well as the relevant underlying probability, statistics, stochastic processes, input analysis, model validation and output analysis. All simulation-related concepts are illustrated in numerous Arena examples, encompassing production lines, manufacturing and inventory systems, transportation systems, and computer information systems in networked settings.· Introduces the concept of discrete event Monte Carlo simulation, the most commonly used methodology for modeli...

General introduction to simulation models

DEFF Research Database (Denmark)

Hisham Beshara Halasa, Tariq; Boklund, Anette

2012-01-01

trials. However, if simulation models would be used, good quality input data must be available. To model FMD, several disease spread models are available. For this project, we chose three simulation model; Davis Animal Disease Spread (DADS), that has been upgraded to DTU-DADS, InterSpread Plus (ISP......Monte Carlo simulation can be defined as a representation of real life systems to gain insight into their functions and to investigate the effects of alternative conditions or actions on the modeled system. Models are a simplification of a system. Most often, it is best to use experiments and field...... trials to investigate the effect of alternative conditions or actions on a specific system. Nonetheless, field trials are expensive and sometimes not possible to conduct, as in case of foot-and-mouth disease (FMD). Instead, simulation models can be a good and cheap substitute for experiments and field...

Virtual Habitat -a dynamic simulation of closed life support systems -human model status

Science.gov (United States)

Markus Czupalla, M. Sc.; Zhukov, Anton; Hwang, Su-Au; Schnaitmann, Jonas

In order to optimize Life Support Systems on a system level, stability questions must be in-vestigated. To do so the exploration group of the Technical University of Munich (TUM) is developing the "Virtual Habitat" (V-HAB) dynamic LSS simulation software. V-HAB shall provide the possibility to conduct dynamic simulations of entire mission scenarios for any given LSS configuration. The Virtual Habitat simulation tool consists of four main modules: • Closed Environment Module (CEM) -monitoring of compounds in a closed environment • Crew Module (CM) -dynamic human simulation • P/C Systems Module (PCSM) -dynamic P/C subsystems • Plant Module (PM) -dynamic plant simulation The core module of the simulation is the dynamic and environment sensitive human module. Introduced in its basic version in 2008, the human module has been significantly updated since, increasing its capabilities and maturity significantly. In this paper three newly added human model subsystems (thermal regulation, digestion and schedule controller) are introduced touching also on the human stress subsystem which is cur-rently under development. Upon the introduction of these new subsystems, the integration of these into the overall V-HAB human model is discussed, highlighting the impact on the most important I/F. The overall human model capabilities shall further be summarized and presented based on meaningful test cases. In addition to the presentation of the results, the correlation strategy for the Virtual Habitat human model shall be introduced assessing the models current confidence level and giving an outlook on the future correlation strategy. Last but not least, the remaining V-HAB mod-ules shall be introduced shortly showing how the human model is integrated into the overall simulation.

Systems Thinking and Simulation Modeling to Inform Childhood Obesity Policy and Practice.

Science.gov (United States)

Powell, Kenneth E; Kibbe, Debra L; Ferencik, Rachel; Soderquist, Chris; Phillips, Mary Ann; Vall, Emily Anne; Minyard, Karen J

In 2007, 31.7% of Georgia adolescents in grades 9-12 were overweight or obese. Understanding the impact of policies and interventions on obesity prevalence among young people can help determine statewide public health and policy strategies. This article describes a systems model, originally launched in 2008 and updated in 2014, that simulates the impact of policy interventions on the prevalence of childhood obesity in Georgia through 2034. In 2008, using information from peer-reviewed reports and quantitative estimates by experts in childhood obesity, physical activity, nutrition, and health economics and policy, a group of legislators, legislative staff members, and experts trained in systems thinking and system dynamics modeling constructed a model simulating the impact of policy interventions on the prevalence of childhood obesity in Georgia through 2034. Use of the 2008 model contributed to passage of a bill requiring annual fitness testing of schoolchildren and stricter enforcement of physical education requirements. We updated the model in 2014. With no policy change, the updated model projects that the prevalence of obesity among children and adolescents aged ≤18 in Georgia would hold at 18% from 2014 through 2034. Mandating daily school physical education (which would reduce prevalence to 12%) and integrating moderate to vigorous physical activity into elementary classrooms (which would reduce prevalence to 10%) would have the largest projected impact. Enacting all policies simultaneously would lower the prevalence of childhood obesity from 18% to 3%. Systems thinking, especially with simulation models, facilitates understanding of complex health policy problems. Using a simulation model to educate legislators, educators, and health experts about the policies that have the greatest short- and long-term impact should encourage strategic investment in low-cost, high-return policies.

An expert system for national economy model simulations

Directory of Open Access Journals (Sweden)

Roljić Lazo

2002-01-01

Full Text Available There are some fundamental economic uncertainties. We cannot forecast economic events with a very high scientific precision. It is very clear that there does not exist a unique 'general' model, which can yield all answers to a wide range of macroeconomic issues. Therefore, we use several different kinds of models on segments of the macroeconomic problem. Different models can distinguish/solve economy desegregation, time series analysis and other subfactors involved in macroeconomic problem solving. A major issue becomes finding a meaningful method to link these econometric models. Macroeconomic models were linked through development of an Expert System for National Economy Model Simulations (ESNEMS. ESNEMS consists of five parts: (1 small-scale short-term national econometric model, (2 Methodology of Interactive Nonlinear Goal Programming (MINGP, (3 data-base of historical macro-economic aggregates, (4 software interface for interactive communications between a model and a decision maker, and (5 software for solving problems. ESNEMS was developed to model the optimum macro-economic policy of a developing country (SFRY-formerly Yugoslavia. Most econometric models are very complex. Optimizing of the economic policy is typically defined as a nonlinear goal programming problem. To solve/optimize these models, a new methodology, MINGP, was developed as a part of ESNEMS. MINGP is methodologically based on linear goal programming and feasible directions method. Using Euler's Homogeneous Function Theorem, MINGP linearizes nonlinear homogeneous functions. The highest priorities in minimizing the objective function are the growth of gross domestic product and the decrease of inflation. In the core of the optimization model, MINGP, there is a small-scale econometric model. This model was designed through analysis of the causal relations in the SFRY's social reproduction process of the past 20 years. The objective of the econometric model is to simulate

Simulation Model of Mobile Detection Systems

International Nuclear Information System (INIS)

Edmunds, T.; Faissol, D.; Yao, Y.

2009-01-01

In this paper, we consider a mobile source that we attempt to detect with man-portable, vehicle-mounted or boat-mounted radiation detectors. The source is assumed to transit an area populated with these mobile detectors, and the objective is to detect the source before it reaches a perimeter. We describe a simulation model developed to estimate the probability that one of the mobile detectors will come in to close proximity of the moving source and detect it. We illustrate with a maritime simulation example. Our simulation takes place in a 10 km by 5 km rectangular bay patrolled by boats equipped with 2-inch x 4-inch x 16-inch NaI detectors. Boats to be inspected enter the bay and randomly proceed to one of seven harbors on the shore. A source-bearing boat enters the mouth of the bay and proceeds to a pier on the opposite side. We wish to determine the probability that the source is detected and its range from target when detected. Patrol boats select the nearest in-bound boat for inspection and initiate an intercept course. Once within an operational range for the detection system, a detection algorithm is started. If the patrol boat confirms the source is not present, it selects the next nearest boat for inspection. Each run of the simulation ends either when a patrol successfully detects a source or when the source reaches its target. Several statistical detection algorithms have been implemented in the simulation model. First, a simple k-sigma algorithm, which alarms with the counts in a time window exceeds the mean background plus k times the standard deviation of background, is available to the user. The time window used is optimized with respect to the signal-to-background ratio for that range and relative speed. Second, a sequential probability ratio test [Wald 1947] is available, and configured in this simulation with a target false positive probability of 0.001 and false negative probability of 0.1. This test is utilized when the mobile detector maintains

Simulation Model of Mobile Detection Systems

Energy Technology Data Exchange (ETDEWEB)

Edmunds, T; Faissol, D; Yao, Y

2009-01-27

In this paper, we consider a mobile source that we attempt to detect with man-portable, vehicle-mounted or boat-mounted radiation detectors. The source is assumed to transit an area populated with these mobile detectors, and the objective is to detect the source before it reaches a perimeter. We describe a simulation model developed to estimate the probability that one of the mobile detectors will come in to close proximity of the moving source and detect it. We illustrate with a maritime simulation example. Our simulation takes place in a 10 km by 5 km rectangular bay patrolled by boats equipped with 2-inch x 4-inch x 16-inch NaI detectors. Boats to be inspected enter the bay and randomly proceed to one of seven harbors on the shore. A source-bearing boat enters the mouth of the bay and proceeds to a pier on the opposite side. We wish to determine the probability that the source is detected and its range from target when detected. Patrol boats select the nearest in-bound boat for inspection and initiate an intercept course. Once within an operational range for the detection system, a detection algorithm is started. If the patrol boat confirms the source is not present, it selects the next nearest boat for inspection. Each run of the simulation ends either when a patrol successfully detects a source or when the source reaches its target. Several statistical detection algorithms have been implemented in the simulation model. First, a simple k-sigma algorithm, which alarms with the counts in a time window exceeds the mean background plus k times the standard deviation of background, is available to the user. The time window used is optimized with respect to the signal-to-background ratio for that range and relative speed. Second, a sequential probability ratio test [Wald 1947] is available, and configured in this simulation with a target false positive probability of 0.001 and false negative probability of 0.1. This test is utilized when the mobile detector maintains

Simulation of warehousing and distribution systems

Directory of Open Access Journals (Sweden)

Drago Pupavac

2005-08-01

Full Text Available The modern world abounds in simulation models. Thousands of organizations use simulation models to solve business problems. Problems in micro logistics systems are a very important segment of the business problems that can be solved by a simulation method. In most cases logistics simulation models should be developed with a purpose to evaluate the performance of individual value-adding indirect resources of logistics system, their possibilities and operational advantages as well as the flow of logistics entities between the plants, warehouses, and customers. Accordingly, this scientific paper elaborates concisely the theoretical characteristics of simulation models and the domains in which the simulation approach is best suited in logistics. Special attention is paid to simulation modeling of warehousing and distribution subsystems of logistic system and there is an example of spreadsheet application in the function of simulated demand for goods from warehouse. Apart from simulation model induction and deduction methods, the description method and a method of information modeling are applied.

The Effects of a Simulation Game on Mental Models about Organizational Systems

Science.gov (United States)

Reese, Rebecca M.

2017-01-01

This mixed methods study was designed to uncover evidence of change to mental models about organizational systems resulting from participation in a simulation game that is based on a system dynamics model. Thirty participants in a 2 day experiential workshop completed a pretest and posttest to assess learning about particular systems concepts.…

Modelling and simulation of electrical energy systems through a complex systems approach using agent-based models

Energy Technology Data Exchange (ETDEWEB)

Kremers, Enrique

2013-10-01

Complexity science aims to better understand the processes of both natural and man-made systems which are composed of many interacting entities at different scales. A disaggregated approach is proposed for simulating electricity systems, by using agent-based models coupled to continuous ones. The approach can help in acquiring a better understanding of the operation of the system itself, e.g. on emergent phenomena or scale effects; as well as in the improvement and design of future smart grids.

Dynamic wind turbine models in power system simulation tool DIgSILENT

DEFF Research Database (Denmark)

Hansen, Anca Daniela; Iov, F.; Sørensen, Poul Ejnar

, connection of the wind turbine at different types of grid and storage systems. Different control strategies have been developed and implemented for these wind turbine concepts, their performance in normal or fault operation being assessed and discussed by means of simulations. The described control......This report presents a collection of models and control strategies developed and implemented in the power system simulation tool PowerFactory DIgSILENT for different wind turbine concepts. It is the second edition of Risø-R-1400(EN) and it gathers and describes a whole wind turbine model database...... of the interaction between the mechanical structure of the wind turbine and the electrical grid during different operational modes. The report provides thus a description of the wind turbines modelling, both at a component level and at a system level. The report contains both the description of DIgSILENT built...

Intraocular Telescopic System Design: Optical and Visual Simulation in a Human Eye Model

OpenAIRE

Zoulinakis, Georgios; Ferrer-Blasco, Teresa

2017-01-01

Purpose. To design an intraocular telescopic system (ITS) for magnifying retinal image and to simulate its optical and visual performance after implantation in a human eye model. Methods. Design and simulation were carried out with a ray-tracing and optical design software. Two different ITS were designed, and their visual performance was simulated using the Liou-Brennan eye model. The difference between the ITS was their lenses’ placement in the eye model and their powers. Ray tracing in bot...

A stochastic simulation model for reliable PV system sizing providing for solar radiation fluctuations

International Nuclear Information System (INIS)

Kaplani, E.; Kaplanis, S.

2012-01-01

Highlights: ► Solar radiation data for European cities follow the Extreme Value or Weibull distribution. ► Simulation model for the sizing of SAPV systems based on energy balance and stochastic analysis. ► Simulation of PV Generator-Loads-Battery Storage System performance for all months. ► Minimum peak power and battery capacity required for reliable SAPV sizing for various European cities. ► Peak power and battery capacity reduced by more than 30% for operation 95% success rate. -- Abstract: The large fluctuations observed in the daily solar radiation profiles affect highly the reliability of the PV system sizing. Increasing the reliability of the PV system requires higher installed peak power (P m ) and larger battery storage capacity (C L ). This leads to increased costs, and makes PV technology less competitive. This research paper presents a new stochastic simulation model for stand-alone PV systems, developed to determine the minimum installed P m and C L for the PV system to be energy independent. The stochastic simulation model developed, makes use of knowledge acquired from an in-depth statistical analysis of the solar radiation data for the site, and simulates the energy delivered, the excess energy burnt, the load profiles and the state of charge of the battery system for the month the sizing is applied, and the PV system performance for the entire year. The simulation model provides the user with values for the autonomy factor d, simulating PV performance in order to determine the minimum P m and C L depending on the requirements of the application, i.e. operation with critical or non-critical loads. The model makes use of NASA’s Surface meteorology and Solar Energy database for the years 1990–2004 for various cities in Europe with a different climate. The results obtained with this new methodology indicate a substantial reduction in installed peak power and battery capacity, both for critical and non-critical operation, when compared to

Simulation of interim spent fuel storage system with discrete event model

International Nuclear Information System (INIS)

Yoon, Wan Ki; Song, Ki Chan; Lee, Jae Sol; Park, Hyun Soo

1989-01-01

This paper describes dynamic simulation of the spent fuel storage system which is described by statistical discrete event models. It visualizes flow and queue of system over time, assesses the operational performance of the system activities and establishes the system components and streams. It gives information on system organization and operation policy with reference to the design. System was tested and analyzed over a number of critical parameters to establish the optimal system. Workforce schedule and resources with long processing time dominate process. A combination of two workforce shifts a day and two cooling pits gives the optimal solution of storage system. Discrete system simulation is an useful tool to get information on optimal design and operation of the storage system. (Author)

Dynamic simulation of a circulating fluidized bed boiler system part I: Description of the dynamic system and transient behavior of sub-models

International Nuclear Information System (INIS)

Kim, Seong Il; Choi, Sang Min; Yang, Jong In

2016-01-01

Dynamic performance simulation of a CFB boiler in a commercial-scale power plant is reported. The boiler system was modeled by a finite number of heat exchanger units, which are sub-grouped into the gas-solid circulation loop, the water-steam circulation loop, and the inter-connected heat exchangers blocks of the boiler. This dynamic model is an extension from the previously reported performance simulation model, which was designed to simulate static performance of the same power plant, where heat and mass for each of the heat exchanger units were balanced for the inter-connected heat exchanger network among the fuel combustion system and the water-steam system. Dynamic performance simulation was achieved by calculating the incremental difference from the previous time step, and progressing for the next time step. Additional discretization of the heat exchanger blocks was necessary to accommodate the dynamic response of the water evaporation and natural circulation as well as the transient response of the metal temperature of the heat exchanger elements. Presentation of the simulation modeling is organized into two parts; system configuration of the model plant and the general approach of the simulation are presented along with the transient behavior of the sub-models in Part I. Dynamic sub-models were integrated in terms of the mass flow and the heat transfer for simulating the CFB boiler system. Dynamic simulation for the open loop response was performed to check the integrated system of the water-steam loop and the solid-gas loop of the total boiler system. Simulation of the total boiler system which includes the closed-loop control system blocks is presented in the following Part II

Dynamic simulation of a circulating fluidized bed boiler system part I: Description of the dynamic system and transient behavior of sub-models

Energy Technology Data Exchange (ETDEWEB)

Kim, Seong Il; Choi, Sang Min; Yang, Jong In [Dept. of Mechanical Engineering, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2016-12-15

Dynamic performance simulation of a CFB boiler in a commercial-scale power plant is reported. The boiler system was modeled by a finite number of heat exchanger units, which are sub-grouped into the gas-solid circulation loop, the water-steam circulation loop, and the inter-connected heat exchangers blocks of the boiler. This dynamic model is an extension from the previously reported performance simulation model, which was designed to simulate static performance of the same power plant, where heat and mass for each of the heat exchanger units were balanced for the inter-connected heat exchanger network among the fuel combustion system and the water-steam system. Dynamic performance simulation was achieved by calculating the incremental difference from the previous time step, and progressing for the next time step. Additional discretization of the heat exchanger blocks was necessary to accommodate the dynamic response of the water evaporation and natural circulation as well as the transient response of the metal temperature of the heat exchanger elements. Presentation of the simulation modeling is organized into two parts; system configuration of the model plant and the general approach of the simulation are presented along with the transient behavior of the sub-models in Part I. Dynamic sub-models were integrated in terms of the mass flow and the heat transfer for simulating the CFB boiler system. Dynamic simulation for the open loop response was performed to check the integrated system of the water-steam loop and the solid-gas loop of the total boiler system. Simulation of the total boiler system which includes the closed-loop control system blocks is presented in the following Part II.

A New Model to Simulate Energy Performance of VRF Systems

Energy Technology Data Exchange (ETDEWEB)

Hong, Tianzhen; Pang, Xiufeng; Schetrit, Oren; Wang, Liping; Kasahara, Shinichi; Yura, Yoshinori; Hinokuma, Ryohei

2014-03-30

This paper presents a new model to simulate energy performance of variable refrigerant flow (VRF) systems in heat pump operation mode (either cooling or heating is provided but not simultaneously). The main improvement of the new model is the introduction of the evaporating and condensing temperature in the indoor and outdoor unit capacity modifier functions. The independent variables in the capacity modifier functions of the existing VRF model in EnergyPlus are mainly room wet-bulb temperature and outdoor dry-bulb temperature in cooling mode and room dry-bulb temperature and outdoor wet-bulb temperature in heating mode. The new approach allows compliance with different specifications of each indoor unit so that the modeling accuracy is improved. The new VRF model was implemented in a custom version of EnergyPlus 7.2. This paper first describes the algorithm for the new VRF model, which is then used to simulate the energy performance of a VRF system in a Prototype House in California that complies with the requirements of Title 24 ? the California Building Energy Efficiency Standards. The VRF system performance is then compared with three other types of HVAC systems: the Title 24-2005 Baseline system, the traditional High Efficiency system, and the EnergyStar Heat Pump system in three typical California climates: Sunnyvale, Pasadena and Fresno. Calculated energy savings from the VRF systems are significant. The HVAC site energy savings range from 51 to 85percent, while the TDV (Time Dependent Valuation) energy savings range from 31 to 66percent compared to the Title 24 Baseline Systems across the three climates. The largest energy savings are in Fresno climate followed by Sunnyvale and Pasadena. The paper discusses various characteristics of the VRF systems contributing to the energy savings. It should be noted that these savings are calculated using the Title 24 prototype House D under standard operating conditions. Actual performance of the VRF systems for real

Investigation of modeling and simulation on a PWR power conversion system with RELAP5

International Nuclear Information System (INIS)

Rui Gao; Yang Yanhua; Lin Meng; Yuan Minghao; Xie Zhengrui

2007-01-01

Based on the power conversion system of nuclear and conventional islands of Dayabay nuclear power station, this paper models the thermal-hydraulic systems for PWR by using the best-estimate program, RELAP5. To simulate the full-scope power conversion system, not only the reactor coolant system (RCP) of nuclear island, but also the main steam system (VVP), turbine steam and drain system (GPV), bypass system (GCT), feedwater system (FW), condensate extraction system (CEX), moisture separator reheater system (GSS), turbine-driven feedwater pump (APP), low-pressure and high-pressure feedwater heater systems (ABP and AHP) of conventional island are considered and modeled. A comparison between the simulated results and the actual data of reactor under full-power demonstrates a fine match for Dayabay, and also manifests the feasibility in simulating full-scope power conversion system of PWR with RELAP5. (author)

Modelling and simulation of railway cable systems

Energy Technology Data Exchange (ETDEWEB)

Teichelmann, G.; Schaub, M.; Simeon, B. [Technische Univ. Muenchen, Garching (Germany). Zentrum Mathematik M2

2005-12-15

Mathematical models and numerical methods for the computation of both static equilibria and dynamic oscillations of railroad catenaries are derived and analyzed. These cable systems form a complex network of string and beam elements and lead to coupled partial differential equations in space and time where constraints and corresponding Lagrange multipliers express the interaction between carrier, contact wire, and pantograph head. For computing static equilibria, three different algorithms are presented and compared, while the dynamic case is treated by a finite element method in space, combined with stabilized time integration of the resulting differential algebraic system. Simulation examples based on reference data from industry illustrate the potential of such computational tools. (orig.)

Modeling and Simulation of DC Power Electronics Systems Using Harmonic State Space (HSS) Method

DEFF Research Database (Denmark)

Kwon, Jun Bum; Wang, Xiongfei; Bak, Claus Leth

2015-01-01

based on the state-space averaging and generalized averaging, these also have limitations to show the same results as with the non-linear time domain simulations. This paper presents a modeling and simulation method for a large dc power electronic system by using Harmonic State Space (HSS) modeling......For the efficiency and simplicity of electric systems, the dc based power electronics systems are widely used in variety applications such as electric vehicles, ships, aircrafts and also in homes. In these systems, there could be a number of dynamic interactions between loads and other dc-dc....... Through this method, the required computation time and CPU memory for large dc power electronics systems can be reduced. Besides, the achieved results show the same results as with the non-linear time domain simulation, but with the faster simulation time which is beneficial in a large network....

Security Information System Digital Simulation

OpenAIRE

Tao Kuang; Shanhong Zhu

2015-01-01

The study built a simulation model for the study of food security information system relay protection. MATLAB-based simulation technology can support the analysis and design of food security information systems. As an example, the food security information system fault simulation, zero-sequence current protection simulation and transformer differential protection simulation are presented in this study. The case studies show that the simulation of food security information system relay protect...

Progress in modeling and simulation.

Science.gov (United States)

Kindler, E

1998-01-01

For the modeling of systems, the computers are more and more used while the other "media" (including the human intellect) carrying the models are abandoned. For the modeling of knowledges, i.e. of more or less general concepts (possibly used to model systems composed of instances of such concepts), the object-oriented programming is nowadays widely used. For the modeling of processes existing and developing in the time, computer simulation is used, the results of which are often presented by means of animation (graphical pictures moving and changing in time). Unfortunately, the object-oriented programming tools are commonly not designed to be of a great use for simulation while the programming tools for simulation do not enable their users to apply the advantages of the object-oriented programming. Nevertheless, there are exclusions enabling to use general concepts represented at a computer, for constructing simulation models and for their easy modification. They are described in the present paper, together with true definitions of modeling, simulation and object-oriented programming (including cases that do not satisfy the definitions but are dangerous to introduce misunderstanding), an outline of their applications and of their further development. In relation to the fact that computing systems are being introduced to be control components into a large spectrum of (technological, social and biological) systems, the attention is oriented to models of systems containing modeling components.

A Simulation Model Of A Picture Archival And Communication System

Science.gov (United States)

D'Silva, Vijay; Perros, Harry; Stockbridge, Chris

1988-06-01

A PACS architecture was simulated to quantify its performance. The model consisted of reading stations, acquisition nodes, communication links, a database management system, and a storage system consisting of magnetic and optical disks. Two levels of storage were simulated, a high-speed magnetic disk system for short term storage, and optical disk jukeboxes for long term storage. The communications link was a single bus via which image data were requested and delivered. Real input data to the simulation model were obtained from surveys of radiology procedures (Bowman Gray School of Medicine). From these the following inputs were calculated: - the size of short term storage necessary - the amount of long term storage required - the frequency of access of each store, and - the distribution of the number of films requested per diagnosis. The performance measures obtained were - the mean retrieval time for an image, - mean queue lengths, and - the utilization of each device. Parametric analysis was done for - the bus speed, - the packet size for the communications link, - the record size on the magnetic disk, - compression ratio, - influx of new images, - DBMS time, and - diagnosis think times. Plots give the optimum values for those values of input speed and device performance which are sufficient to achieve subsecond image retrieval times

Anatomy and Physiology of Multiscale Modeling and Simulation in Systems Medicine

NARCIS (Netherlands)

Mizeranschi, A.; Groen, D.; Borgdorff, J.; Hoekstra, A.G.; Chopard, B.; Dubitzky, W.; Schmitz, U; Wolkenhauer, O.

2016-01-01

Systems medicine is the application of systems biology concepts, methods, and tools to medical research and practice. It aims to integrate data and knowledge from different disciplines into biomedical models and simulations for the understanding, prevention, cure, and management of complex diseases.

Digital simulation of power electronic systems

International Nuclear Information System (INIS)

Mehring, P.; Jentsch, W.; John, G.; Kraemer, D.

1981-01-01

The following paper contains the final report on the NETSIM-Project. The purpose of this project is to develop a special digital simulation system, which could serve as a base for routine application of simulation in planning and development of power electronic systems. The project is realized in two steps. First a basic network analysis system is established. With this system the basic models and methods in treating power electronic networks could be probed. The resulting system is then integrated into a general digital simulation system for continous systems (CSSL-System). This integrated simulation system allows for convenient modeling and simulation of power electronic systems. (orig.) [de

Engineering the future of military tactical vehicles and systems with modeling and simulation

Science.gov (United States)

Loew, Matthew; Watters, Brock

2005-05-01

Stewart & Stevenson has developed a Modeling and Simulation approach based on Systems Engineering principles for the development of future military vehicles and systems. This approach starts with a requirements analysis phase that captures and distills the design requirements into a list of parameterized values. A series of executable engineering models are constructed to allow the requirements to be transformed into systems with definable architectures with increasing levels of fidelity. Required performance parameters are available for importation into a variety of modeling and simulation tools including PTC Pro/ENGINEER (for initial engineering models, mechanisms, packaging, and detailed 3-Dimensional solid models), LMS International Virtual.Lab Motion (for vehicle dynamics and ride analysis) and AVL Cruise (Powertrain simulations). Structural analysis and optimization (performed in ANSYS, Pro/MECHANICA, and Altair OptiStruct) is based on the initial geometry from Pro/ENGINEER. Spreadsheets are used for requirements analysis, design documentation and first-order studies. Collectively, these models serve as templates for all design activities. Design variables initially studied within a simplified system model can be cascaded down as the new requirements for a sub-system model. By utilizing this approach premature decisions on systems architectures can be avoided. Ultimately, the systems that are developed are optimally able to meet the requirements by utilizing this top-down approach. Additionally, this M&S approach is seen as a life-cycle tool useful in initially assisting with project management activities through the initial and detail design phases and serves as a template for testing and validation/verification activities. Furthermore, because of the multi-tiered approach, there is natural re-use possible with the models as well.

Modeling and Simulation of Multi-scale Environmental Systems with Generalized Hybrid Petri Nets

Directory of Open Access Journals (Sweden)

Mostafa eHerajy

2015-07-01

Full Text Available Predicting and studying the dynamics and properties of environmental systems necessitates the construction and simulation of mathematical models entailing different levels of complexities. Such type of computational experiments often require the combination of discrete and continuous variables as well as processes operating at different time scales. Furthermore, the iterative steps of constructing and analyzing environmental models might involve researchers with different background. Hybrid Petri nets may contribute in overcoming such challenges as they facilitate the implementation of systems integrating discrete and continuous dynamics. Additionally, the visual depiction of model components will inevitably help to bridge the gap between scientists with distinct expertise working on the same problem. Thus, modeling environmental systems with hybrid Petri nets enables the construction of complex processes while keeping the models comprehensible for researchers working on the same project with significantly divergent education path. In this paper we propose the utilization of a special class of hybrid Petri nets, Generalized Hybrid Petri Nets (GHPN, to model and simulate environmental systems exposing processes interacting at different time-scales. GHPN integrate stochastic and deterministic semantics as well as other types of special basic events. Moreover, a case study is presented to illustrate the use of GHPN in constructing and simulating multi-timescale environmental scenarios.

A method of Modelling and Simulating the Back-to-Back Modular Multilevel Converter HVDC Transmission System

Science.gov (United States)

Wang, Lei; Fan, Youping; Zhang, Dai; Ge, Mengxin; Zou, Xianbin; Li, Jingjiao

2017-09-01

This paper proposes a method to simulate a back-to-back modular multilevel converter (MMC) HVDC transmission system. In this paper we utilize an equivalent networks to simulate the dynamic power system. Moreover, to account for the performance of converter station, core components of model of the converter station gives a basic model of simulation. The proposed method is applied to an equivalent real power system.

A new synoptic scale resolving global climate simulation using the Community Earth System Model

Science.gov (United States)

Small, R. Justin; Bacmeister, Julio; Bailey, David; Baker, Allison; Bishop, Stuart; Bryan, Frank; Caron, Julie; Dennis, John; Gent, Peter; Hsu, Hsiao-ming; Jochum, Markus; Lawrence, David; Muñoz, Ernesto; diNezio, Pedro; Scheitlin, Tim; Tomas, Robert; Tribbia, Joseph; Tseng, Yu-heng; Vertenstein, Mariana

2014-12-01

High-resolution global climate modeling holds the promise of capturing planetary-scale climate modes and small-scale (regional and sometimes extreme) features simultaneously, including their mutual interaction. This paper discusses a new state-of-the-art high-resolution Community Earth System Model (CESM) simulation that was performed with these goals in mind. The atmospheric component was at 0.25° grid spacing, and ocean component at 0.1°. One hundred years of "present-day" simulation were completed. Major results were that annual mean sea surface temperature (SST) in the equatorial Pacific and El-Niño Southern Oscillation variability were well simulated compared to standard resolution models. Tropical and southern Atlantic SST also had much reduced bias compared to previous versions of the model. In addition, the high resolution of the model enabled small-scale features of the climate system to be represented, such as air-sea interaction over ocean frontal zones, mesoscale systems generated by the Rockies, and Tropical Cyclones. Associated single component runs and standard resolution coupled runs are used to help attribute the strengths and weaknesses of the fully coupled run. The high-resolution run employed 23,404 cores, costing 250 thousand processor-hours per simulated year and made about two simulated years per day on the NCAR-Wyoming supercomputer "Yellowstone."

Modelling and real-time simulation of continuous-discrete systems in mechatronics

Energy Technology Data Exchange (ETDEWEB)

Lindow, H. [Rostocker, Magdeburg (Germany)

1996-12-31

This work presents a methodology for simulation and modelling of systems with continuous - discrete dynamics. It derives hybrid discrete event models from Lagrange`s equations of motion. This method combines continuous mechanical, electrical and thermodynamical submodels on one hand with discrete event models an the other hand into a hybrid discrete event model. This straight forward software development avoids numeric overhead.

Dynamics of global vegetation biomass simulated by the integrated Earth System Model

Science.gov (United States)

Mao, J.; Shi, X.; Di Vittorio, A. V.; Thornton, P. E.; Piao, S.; Yang, X.; Truesdale, J. E.; Bond-Lamberty, B. P.; Chini, L. P.; Thomson, A. M.; Hurtt, G. C.; Collins, W.; Edmonds, J.

2014-12-01

The global vegetation biomass stores huge amounts of carbon and is thus important to the global carbon budget (Pan et al., 2010). For the past few decades, different observation-based estimates and modeling of biomass in the above- and below-ground vegetation compartments have been comprehensively conducted (Saatchi et al., 2011; Baccini et al., 2012). However, uncertainties still exist, in particular for the simulation of biomass magnitude, tendency, and the response of biomass to climatic conditions and natural and human disturbances. The recently successful coupling of the integrated Earth System Model (iESM) (Di Vittorio et al., 2014; Bond-Lamberty et al., 2014), which links the Global Change Assessment Model (GCAM), Global Land-use Model (GLM), and Community Earth System Model (CESM), offers a great opportunity to understand the biomass-related dynamics in a fully-coupled natural and human modeling system. In this study, we focus on the systematic analysis and evaluation of the iESM simulated historical (1850-2005) and future (2006-2100) biomass changes and the response of the biomass dynamics to various impact factors, in particular the human-induced Land Use/Land Cover Change (LULCC). By analyzing the iESM simulations with and without the interactive LULCC feedbacks, we further study how and where the climate feedbacks affect socioeconomic decisions and LULCC, such as to alter vegetation carbon storage. References Pan Y et. al: A large and persistent carbon sink in the World's forests. Science 2011, 333:988-993. Saatchi SS et al: Benchmark map of forest carbon stocks in tropical regions across three continents. Proc Natl Acad Sci 2011, 108:9899-9904. Baccini A et al: Estimated carbon dioxide emissions from tropical deforestation improved by carbon-density maps. Nature Clim Change 2012, 2:182-185. Di Vittorio AV et al: From land use to land cover: restoring the afforestation signal in a coupled integrated assessment-earth system model and the implications for

Methodology to evaluate the performance of simulation models for alternative compiler and operating system configurations

Science.gov (United States)

Simulation modelers increasingly require greater flexibility for model implementation on diverse operating systems, and they demand high computational speed for efficient iterative simulations. Additionally, model users may differ in preference for proprietary versus open-source software environment...

The mesoscale dispersion modeling system a simulation tool for development of an emergency response system

International Nuclear Information System (INIS)

Uliasz, M.

1990-01-01

The mesoscale dispersion modeling system is under continuous development. The included numerical models require further improvements and evaluation against data from meteorological and tracer field experiments. The system can not be directly applied to real time predictions. However, it seems to be a useful simulation tool for solving several problems related to planning the monitoring network and development of the emergency response system for the nuclear power plant located in a coastal area. The modeling system can be also applied to another environmental problems connected with air pollution dispersion in complex terrain. The presented numerical models are designed for the use on personal computers and are relatively fast in comparison with the similar mesoscale models developed on mainframe computers

The Australian Computational Earth Systems Simulator

Science.gov (United States)

Mora, P.; Muhlhaus, H.; Lister, G.; Dyskin, A.; Place, D.; Appelbe, B.; Nimmervoll, N.; Abramson, D.

2001-12-01

Numerical simulation of the physics and dynamics of the entire earth system offers an outstanding opportunity for advancing earth system science and technology but represents a major challenge due to the range of scales and physical processes involved, as well as the magnitude of the software engineering effort required. However, new simulation and computer technologies are bringing this objective within reach. Under a special competitive national funding scheme to establish new Major National Research Facilities (MNRF), the Australian government together with a consortium of Universities and research institutions have funded construction of the Australian Computational Earth Systems Simulator (ACcESS). The Simulator or computational virtual earth will provide the research infrastructure to the Australian earth systems science community required for simulations of dynamical earth processes at scales ranging from microscopic to global. It will consist of thematic supercomputer infrastructure and an earth systems simulation software system. The Simulator models and software will be constructed over a five year period by a multi-disciplinary team of computational scientists, mathematicians, earth scientists, civil engineers and software engineers. The construction team will integrate numerical simulation models (3D discrete elements/lattice solid model, particle-in-cell large deformation finite-element method, stress reconstruction models, multi-scale continuum models etc) with geophysical, geological and tectonic models, through advanced software engineering and visualization technologies. When fully constructed, the Simulator aims to provide the software and hardware infrastructure needed to model solid earth phenomena including global scale dynamics and mineralisation processes, crustal scale processes including plate tectonics, mountain building, interacting fault system dynamics, and micro-scale processes that control the geological, physical and dynamic

Component and system simulation models for High Flux Isotope Reactor

International Nuclear Information System (INIS)

Sozer, A.

1989-08-01

Component models for the High Flux Isotope Reactor (HFIR) have been developed. The models are HFIR core, heat exchangers, pressurizer pumps, circulation pumps, letdown valves, primary head tank, generic transport delay (pipes), system pressure, loop pressure-flow balance, and decay heat. The models were written in FORTRAN and can be run on different computers, including IBM PCs, as they do not use any specific simulation languages such as ACSL or CSMP. 14 refs., 13 figs

Multi-agent systems simulation and applications

CERN Document Server

Uhrmacher, Adelinde M

2009-01-01

Methodological Guidelines for Modeling and Developing MAS-Based SimulationsThe intersection of agents, modeling, simulation, and application domains has been the subject of active research for over two decades. Although agents and simulation have been used effectively in a variety of application domains, much of the supporting research remains scattered in the literature, too often leaving scientists to develop multi-agent system (MAS) models and simulations from scratch. Multi-Agent Systems: Simulation and Applications provides an overdue review of the wide ranging facets of MAS simulation, i

Dynamic modeling and simulation of EBR-II steam generator system

International Nuclear Information System (INIS)

Berkan, R.C.; Upadhyaya, B.R.

1989-01-01

This paper presents a low order dynamic model of the Experimental breeder Reactor-II (EBR-II) steam generator system. The model development includes the application of energy, mass and momentum balance equations in state-space form. The model also includes a three-element controller for the drum water level control problem. The simulation results for low-level perturbations exhibit the inherently stable characteristics of the steam generator. The predictions of test transients also verify the consistency of this low order model

Modelling and simulating a crisis management system: an organisational perspective

Science.gov (United States)

Chaawa, Mohamed; Thabet, Inès; Hanachi, Chihab; Ben Said, Lamjed

2017-04-01

Crises are complex situations due to the dynamism of the environment, its unpredictability and the complexity of the interactions among several different and autonomous involved organisations. In such a context, establishing an organisational view as well as structuring organisations' communications and their functioning is a crucial requirement. In this article, we propose a multi-agent organisational model (OM) to abstract, simulate and analyse a crisis management system (CMS). The objective is to evaluate the CMS from an organisational view, to assess its strength as well as its weakness and to provide deciders with some recommendations for a more flexible and reactive CMS. The proposed OM is illustrated through a real case study: a snowstorm in a Tunisian region. More precisely, we made the following contribution: firstly, we provide an environmental model that identifies the concepts involved in the crisis. Then, we define a role model that copes with the involved actors. In addition, we specify the organisational structure and the interaction model that rule communications and structure actors' functioning. Those models, built following the GAIA methodology, abstract the CMS from an organisational perspective. Finally, we implemented a customisable multi-agent simulator based on the Janus platform to analyse, through several performed simulations, the organisational model.

Review on modeling and simulation of interdependent critical infrastructure systems

International Nuclear Information System (INIS)

Ouyang, Min

2014-01-01

Modern societies are becoming increasingly dependent on critical infrastructure systems (CISs) to provide essential services that support economic prosperity, governance, and quality of life. These systems are not alone but interdependent at multiple levels to enhance their overall performance. However, recent worldwide events such as the 9/11 terrorist attack, Gulf Coast hurricanes, the Chile and Japanese earthquakes, and even heat waves have highlighted that interdependencies among CISs increase the potential for cascading failures and amplify the impact of both large and small scale initial failures into events of catastrophic proportions. To better understand CISs to support planning, maintenance and emergency decision making, modeling and simulation of interdependencies across CISs has recently become a key field of study. This paper reviews the studies in the field and broadly groups the existing modeling and simulation approaches into six types: empirical approaches, agent based approaches, system dynamics based approaches, economic theory based approaches, network based approaches, and others. Different studies for each type of the approaches are categorized and reviewed in terms of fundamental principles, such as research focus, modeling rationale, and the analysis method, while different types of approaches are further compared according to several criteria, such as the notion of resilience. Finally, this paper offers future research directions and identifies critical challenges in the field. - Highlights: • Modeling approaches on interdependent critical infrastructure systems are reviewed. • I mainly review empirical, agent-based, system-dynamics, economic, network approaches. • Studies by each approach are sorted out in terms of fundamental principles. • Different approaches are further compared with resilience as the main criterion

Development and application of a crossbreeding simulation model for goat production systems in tropical regions.

Science.gov (United States)

Tsukahara, Y; Oishi, K; Hirooka, H

2011-12-01

A deterministic simulation model was developed to estimate biological production efficiency and to evaluate goat crossbreeding systems under tropical conditions. The model involves 5 production systems: pure indigenous, first filial generations (F1), backcross (BC), composite breeds of F1 (CMP(F1)), and BC (CMP(BC)). The model first simulates growth, reproduction, lactation, and energy intakes of a doe and a kid on a 1-d time step at the individual level and thereafter the outputs are integrated into the herd dynamics program. The ability of the model to simulate individual performances was tested under a base situation. The simulation results represented daily BW changes, ME requirements, and milk yield and the estimates were within the range of published data. Two conventional goat production scenarios (an intensive milk production scenario and an integrated goat and oil palm production scenario) in Malaysia were examined. The simulation results of the intensive milk production scenario showed the greater production efficiency of the CMP(BC) and CMP(F1) systems and decreased production efficiency of the F1 and BC systems. The results of the integrated goat and oil palm production scenario showed that the production efficiency and stocking rate were greater for the indigenous goats than for the crossbreeding systems.

Modeling and Simulation of an Unmanned Ground Vehicle Power System

Science.gov (United States)

2014-03-28

Wilhelm, A. N., Surgenor, B. W., and Pharoah, J. G., “Design and evaluation of a micro-fuel-cell-based power system for a mobile robot,” Mechatronics ... Embedded Control Systems ], Control Engineering, 91–116, Birkhuser Boston (2005). [12] Alur, R., Courcoubetis, C., Halbwachs, N., Henzinger, T., Ho, P.-H...Modeling and Simulation of an Unmanned Ground Vehicle Power System John Brodericka∗, Jack Hartnerb, Dawn Tilburya, and Ella Atkinsa aThe University

DECISION WITH ARTIFICIAL NEURAL NETWORKS IN DISCRETE EVENT SIMULATION MODELS ON A TRAFFIC SYSTEM

Directory of Open Access Journals (Sweden)

Marília Gonçalves Dutra da Silva

2016-04-01

Full Text Available ABSTRACT This work aims to demonstrate the use of a mechanism to be applied in the development of the discrete-event simulation models that perform decision operations through the implementation of an artificial neural network. Actions that involve complex operations performed by a human agent in a process, for example, are often modeled in simplified form with the usual mechanisms of simulation software. Therefore, it was chosen a traffic system controlled by a traffic officer with a flow of vehicles and pedestrians to demonstrate the proposed solution. From a module built in simulation software itself, it was possible to connect the algorithm for intelligent decision to the simulation model. The results showed that the model elaborated responded as expected when it was submitted to actions, which required different decisions to maintain the operation of the system with changes in the flow of people and vehicles.

Thermal unit availability modeling in a regional simulation model

International Nuclear Information System (INIS)

Yamayee, Z.A.; Port, J.; Robinett, W.

1983-01-01

The System Analysis Model (SAM) developed under the umbrella of PNUCC's System Analysis Committee is capable of simulating the operation of a given load/resource scenario. This model employs a Monte-Carlo simulation to incorporate uncertainties. Among uncertainties modeled is thermal unit availability both for energy simulation (seasonal) and capacity simulations (hourly). This paper presents the availability modeling in the capacity and energy models. The use of regional and national data in deriving the two availability models, the interaction between the two and modifications made to the capacity model in order to reflect regional practices is presented. A sample problem is presented to show the modification process. Results for modeling a nuclear unit using NERC-GADS is presented

A model library for simulation and benchmarking of integrated urban wastewater systems

DEFF Research Database (Denmark)

Saagi, R.; Flores Alsina, Xavier; Kroll, J. S.

2017-01-01

This paper presents a freely distributed, open-source toolbox to predict the behaviour of urban wastewater systems (UWS). The proposed library is used to develop a system-wide Benchmark Simulation Model (BSM-UWS) for evaluating (local/global) control strategies in urban wastewater systems (UWS...

A radiation monitoring system model for the Laguna Verde nuclear power training simulator

International Nuclear Information System (INIS)

Ocampo, M.H.; DeAlbornoz, B.A.

1988-01-01

A model for the Radiation Monitoring System of the Laguna Verde Boiling Water Reactor training simulator is presented. This model comprises enough definitions to assure interactions with the processes related, directly or indirectly, with the transport of radioisotopes. It is capable of following a dynamic behavior of the plant so an operator could be trained to become aware of nuclear radiation hazards. The model is composed of three parts: the electronics for the Process and Area Radiation Monitoring System; a lumped parameter transport model for the most representative radioisotopes; and the interactions with the modeled processes as well as with process not being simulated. The first part represents the radiation monitor controls in the vertical board panels of the nuclear station. The second part allows the carrying of nuclear isotopes between processes. The third part defines the way that the process interacts with the electronics at the point of release to environment or the point of detection. Each part of the model has been tested individually, and the transport model has been incorporated as a part of each process required to simulate nuclear radiation. The model parameters has been calculated using typical BWR nuclear radiation data, and Laguna Verde heat balance data at 100% design power. However, tunning will be necessary once the Simulator is integrated and tested. The tunning allows each detecting channel to behave as expected

Hardware-in-the-Loop Modeling and Simulation Methods for Daylight Systems in Buildings

Science.gov (United States)

Mead, Alex Robert

This dissertation introduces hardware-in-the-loop modeling and simulation techniques to the daylighting community, with specific application to complex fenestration systems. No such application of this class of techniques, optimally combining mathematical-modeling and physical-modeling experimentation, is known to the author previously in the literature. Daylighting systems in buildings have a large impact on both the energy usage of a building as well as the occupant experience within a space. As such, a renewed interest has been placed on designing and constructing buildings with an emphasis on daylighting in recent times as part of the "green movement.''. Within daylighting systems, a specific subclass of building envelope is receiving much attention: complex fenestration systems (CFSs). CFSs are unique as compared to regular fenestration systems (e.g. glazing) in the regard that they allow for non-specular transmission of daylight into a space. This non-specular nature can be leveraged by designers to "optimize'' the times of the day and the days of the year that daylight enters a space. Examples of CFSs include: Venetian blinds, woven fabric shades, and prismatic window coatings. In order to leverage the non-specular transmission properties of CFSs, however, engineering analysis techniques capable of faithfully representing the physics of these systems are needed. Traditionally, the analysis techniques available to the daylighting community fall broadly into three classes: simplified techniques, mathematical-modeling and simulation, and physical-modeling and experimentation. Simplified techniques use "rules-of-thumb'' heuristics to provide insights for simple daylighting systems. Mathematical-modeling and simulation use complex numerical models to provide more detailed insights into system performance. Finally, physical-models can be instrumented and excited using artificial and natural light sources to provide performance insight into a daylighting system

Real-time distributed simulation using the Modular Modeling System interfaced to a Bailey NETWORK 90 system

International Nuclear Information System (INIS)

Edwards, R.M.; Turso, J.A.; Garcia, H.E.; Ghie, M.H.; Dharap, S.; Lee, S.

1991-01-01

The Modular Modeling System was adapted for real-time simulation testing of diagnostic expert systems in 1987. The early approach utilized an available general purpose mainframe computer which operated the simulation and diagnostic program in the multitasking environment of the mainframe. That research program was subsequently expanded to intelligent distributed control applications incorporating microprocessor based controllers with the aid of an equipment grant from the National Science Foundation (NSF). The Bailey NETWORK 90 microprocessor-based control system, acquired with the NSF grant, has been operational since April of 1990 and has been interfaced to both VAX mainframe and PC simulations of power plant processes in order to test and demonstrate advanced control and diagnostic concepts. This paper discusses the variety of techniques that have been used and which are under development to interface simulations and other distributed control functions to the Penn State Bailey system

Using multi-criteria analysis of simulation models to understand complex biological systems

Science.gov (United States)

Maureen C. Kennedy; E. David. Ford

2011-01-01

Scientists frequently use computer-simulation models to help solve complex biological problems. Typically, such models are highly integrated, they produce multiple outputs, and standard methods of model analysis are ill suited for evaluating them. We show how multi-criteria optimization with Pareto optimality allows for model outputs to be compared to multiple system...

Stochastic modeling analysis and simulation

CERN Document Server

Nelson, Barry L

1995-01-01

A coherent introduction to the techniques for modeling dynamic stochastic systems, this volume also offers a guide to the mathematical, numerical, and simulation tools of systems analysis. Suitable for advanced undergraduates and graduate-level industrial engineers and management science majors, it proposes modeling systems in terms of their simulation, regardless of whether simulation is employed for analysis. Beginning with a view of the conditions that permit a mathematical-numerical analysis, the text explores Poisson and renewal processes, Markov chains in discrete and continuous time, se

Simulation model for wind energy storage systems. Volume I. Technical report. [SIMWEST code

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Chan, Y.K.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume I gives a brief overview of the SIMWEST program and describes the two NASA defined simulation studies.

Performance Evaluation of UML2-Modeled Embedded Streaming Applications with System-Level Simulation

Directory of Open Access Journals (Sweden)

Arpinen Tero

2009-01-01

Full Text Available This article presents an efficient method to capture abstract performance model of streaming data real-time embedded systems (RTESs. Unified Modeling Language version 2 (UML2 is used for the performance modeling and as a front-end for a tool framework that enables simulation-based performance evaluation and design-space exploration. The adopted application meta-model in UML resembles the Kahn Process Network (KPN model and it is targeted at simulation-based performance evaluation. The application workload modeling is done using UML2 activity diagrams, and platform is described with structural UML2 diagrams and model elements. These concepts are defined using a subset of the profile for Modeling and Analysis of Realtime and Embedded (MARTE systems from OMG and custom stereotype extensions. The goal of the performance modeling and simulation is to achieve early estimates on task response times, processing element, memory, and on-chip network utilizations, among other information that is used for design-space exploration. As a case study, a video codec application on multiple processors is modeled, evaluated, and explored. In comparison to related work, this is the first proposal that defines transformation between UML activity diagrams and streaming data application workload meta models and successfully adopts it for RTES performance evaluation.

Agent-based modeling and simulation of clean heating system adoption in Norway

Energy Technology Data Exchange (ETDEWEB)

Sopha, Bertha Maya

2011-03-15

A sound climate policy encouraging clean energy investment is important to mitigate global warming. Previous research has demonstrated that consumer choice indeed plays an important role in adoption of sustainable technologies. This thesis strives to gain a better understanding of consumers' decision-making on heating systems and to explore the potential application of agent-based modeling (ABM) in exploring mechanism underlying adoption in which heating system adoption by Norwegian households is taken up as a case study. An interdisciplinary approach, applying various established theories including those of psychology, is applied to create a model for consumer behavior and implement this behavior in an Agent-Based Model (ABM) to simulate heating technology diffusion. A mail-survey, carried out in autumn 2008, is a means to collect information for parameterizing the agent-based model, for gaining empirical facts, and for validating the developed model at micro-level. Survey sample consisted of 1500 Norwegian households drawn from population register and 1500 wood pellet users in Norway. The response rates were 10.3% and 34.6% for population sample and wood pellet sample respectively. This study is divided into two parts; empirical analysis and agent-based simulation. The empirical analysis aims at fully understanding the important aspects of adoption decision and their implications, in order to assist simulation. The analysis particularly contributes to the identification of differences/similarities between adopters and non adopters of wood pellet heating with respects to some key points of adoption derived from different theories, psychological factors underlying the adoption-decision of wood pellet heating, and the rationales underlying Norwegian households' decisions regarding their future heating system. The simulation study aims at exploring the mechanism of heterogeneous household decision-making giving rise to the diffusion of heating systems, and

Modelling of reactor control and protection systems in the core simulator program GARLIC

International Nuclear Information System (INIS)

Beraha, D.; Lupas, O.; Ploegert, K.

1984-01-01

For analysis of the interaction between control and limitation systems and the power distribution in the reactor core, a valuable tool is provided by the joint simulation of the core and the interacting systems. To this purpose, the core simulator GARLIC has been enhanced by models of the systems for controlling and limiting the reactor power and the power distribution in the core as well as by modules for calculating safety related core parameters. The computer-based core protection system, first installed in the Grafenrheinfeld NPP, has been included in the simulation. In order to evaluate the accuracy of GARLIC-simulations, the code has been compared with a design code in the train of a verification phase. The report describes the program extensions and the results of the verification. (orig.) [de

Understanding Emergency Care Delivery Through Computer Simulation Modeling.

Science.gov (United States)

Laker, Lauren F; Torabi, Elham; France, Daniel J; Froehle, Craig M; Goldlust, Eric J; Hoot, Nathan R; Kasaie, Parastu; Lyons, Michael S; Barg-Walkow, Laura H; Ward, Michael J; Wears, Robert L

2018-02-01

In 2017, Academic Emergency Medicine convened a consensus conference entitled, "Catalyzing System Change through Health Care Simulation: Systems, Competency, and Outcomes." This article, a product of the breakout session on "understanding complex interactions through systems modeling," explores the role that computer simulation modeling can and should play in research and development of emergency care delivery systems. This article discusses areas central to the use of computer simulation modeling in emergency care research. The four central approaches to computer simulation modeling are described (Monte Carlo simulation, system dynamics modeling, discrete-event simulation, and agent-based simulation), along with problems amenable to their use and relevant examples to emergency care. Also discussed is an introduction to available software modeling platforms and how to explore their use for research, along with a research agenda for computer simulation modeling. Through this article, our goal is to enhance adoption of computer simulation, a set of methods that hold great promise in addressing emergency care organization and design challenges. © 2017 by the Society for Academic Emergency Medicine.

Multiagent Modeling and Simulation in Human-Robot Mission Operations Work System Design

Science.gov (United States)

Sierhuis, Maarten; Clancey, William J.; Sims, Michael H.; Shafto, Michael (Technical Monitor)

2001-01-01

This paper describes a collaborative multiagent modeling and simulation approach for designing work systems. The Brahms environment is used to model mission operations for a semi-autonomous robot mission to the Moon at the work practice level. It shows the impact of human-decision making on the activities and energy consumption of a robot. A collaborative work systems design methodology is described that allows informal models, created with users and stakeholders, to be used as input to the development of formal computational models.

Mass balances for a biological life support system simulation model

Science.gov (United States)

Volk, Tyler; Rummel, John D.

1987-01-01

Design decisions to aid the development of future space based biological life support systems (BLSS) can be made with simulation models. The biochemistry stoichiometry was developed for: (1) protein, carbohydrate, fat, fiber, and lignin production in the edible and inedible parts of plants; (2) food consumption and production of organic solids in urine, feces, and wash water by the humans; and (3) operation of the waste processor. Flux values for all components are derived for a steady state system with wheat as the sole food source. The large scale dynamics of a materially closed (BLSS) computer model is described in a companion paper. An extension of this methodology can explore multifood systems and more complex biochemical dynamics while maintaining whole system closure as a focus.

A simulation model for reliability evaluation of Space Station power systems

Science.gov (United States)

Singh, C.; Patton, A. D.; Kumar, Mudit; Wagner, H.

1988-01-01

A detailed simulation model for the hybrid Space Station power system is presented which allows photovoltaic and solar dynamic power sources to be mixed in varying proportions. The model considers the dependence of reliability and storage characteristics during the sun and eclipse periods, and makes it possible to model the charging and discharging of the energy storage modules in a relatively accurate manner on a continuous basis.

Simulation of groundwater flow in the glacial aquifer system of northeastern Wisconsin with variable model complexity

Science.gov (United States)

Juckem, Paul F.; Clark, Brian R.; Feinstein, Daniel T.

2017-05-04

The U.S. Geological Survey, National Water-Quality Assessment seeks to map estimated intrinsic susceptibility of the glacial aquifer system of the conterminous United States. Improved understanding of the hydrogeologic characteristics that explain spatial patterns of intrinsic susceptibility, commonly inferred from estimates of groundwater age distributions, is sought so that methods used for the estimation process are properly equipped. An important step beyond identifying relevant hydrogeologic datasets, such as glacial geology maps, is to evaluate how incorporation of these resources into process-based models using differing levels of detail could affect resulting simulations of groundwater age distributions and, thus, estimates of intrinsic susceptibility.This report describes the construction and calibration of three groundwater-flow models of northeastern Wisconsin that were developed with differing levels of complexity to provide a framework for subsequent evaluations of the effects of process-based model complexity on estimations of groundwater age distributions for withdrawal wells and streams. Preliminary assessments, which focused on the effects of model complexity on simulated water levels and base flows in the glacial aquifer system, illustrate that simulation of vertical gradients using multiple model layers improves simulated heads more in low-permeability units than in high-permeability units. Moreover, simulation of heterogeneous hydraulic conductivity fields in coarse-grained and some fine-grained glacial materials produced a larger improvement in simulated water levels in the glacial aquifer system compared with simulation of uniform hydraulic conductivity within zones. The relation between base flows and model complexity was less clear; however, the relation generally seemed to follow a similar pattern as water levels. Although increased model complexity resulted in improved calibrations, future application of the models using simulated particle

Simulation model for wind energy storage systems. Volume III. Program descriptions. [SIMWEST CODE

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume III, the SIMWEST program description contains program descriptions, flow charts and program listings for the SIMWEST Model Generation Program, the Simulation program, the File Maintenance program and the Printer Plotter program. Volume III generally would not be required by SIMWEST user.

Next-Generation Climate Modeling Science Challenges for Simulation, Workflow and Analysis Systems

Science.gov (United States)

Koch, D. M.; Anantharaj, V. G.; Bader, D. C.; Krishnan, H.; Leung, L. R.; Ringler, T.; Taylor, M.; Wehner, M. F.; Williams, D. N.

2016-12-01

We will present two examples of current and future high-resolution climate-modeling research that are challenging existing simulation run-time I/O, model-data movement, storage and publishing, and analysis. In each case, we will consider lessons learned as current workflow systems are broken by these large-data science challenges, as well as strategies to repair or rebuild the systems. First we consider the science and workflow challenges to be posed by the CMIP6 multi-model HighResMIP, involving around a dozen modeling groups performing quarter-degree simulations, in 3-member ensembles for 100 years, with high-frequency (1-6 hourly) diagnostics, which is expected to generate over 4PB of data. An example of science derived from these experiments will be to study how resolution affects the ability of models to capture extreme-events such as hurricanes or atmospheric rivers. Expected methods to transfer (using parallel Globus) and analyze (using parallel "TECA" software tools) HighResMIP data for such feature-tracking by the DOE CASCADE project will be presented. A second example will be from the Accelerated Climate Modeling for Energy (ACME) project, which is currently addressing challenges involving multiple century-scale coupled high resolution (quarter-degree) climate simulations on DOE Leadership Class computers. ACME is anticipating production of over 5PB of data during the next 2 years of simulations, in order to investigate the drivers of water cycle changes, sea-level-rise, and carbon cycle evolution. The ACME workflow, from simulation to data transfer, storage, analysis and publication will be presented. Current and planned methods to accelerate the workflow, including implementing run-time diagnostics, and implementing server-side analysis to avoid moving large datasets will be presented.

The General-Use Nodal Network Solver (GUNNS) Modeling Package for Space Vehicle Flow System Simulation

Science.gov (United States)

Harvey, Jason; Moore, Michael

2013-01-01

The General-Use Nodal Network Solver (GUNNS) is a modeling software package that combines nodal analysis and the hydraulic-electric analogy to simulate fluid, electrical, and thermal flow systems. GUNNS is developed by L-3 Communications under the TS21 (Training Systems for the 21st Century) project for NASA Johnson Space Center (JSC), primarily for use in space vehicle training simulators at JSC. It has sufficient compactness and fidelity to model the fluid, electrical, and thermal aspects of space vehicles in real-time simulations running on commodity workstations, for vehicle crew and flight controller training. It has a reusable and flexible component and system design, and a Graphical User Interface (GUI), providing capability for rapid GUI-based simulator development, ease of maintenance, and associated cost savings. GUNNS is optimized for NASA's Trick simulation environment, but can be run independently of Trick.

Review of Dynamic Modeling and Simulation of Large Scale Belt Conveyor System

Science.gov (United States)

He, Qing; Li, Hong

Belt conveyor is one of the most important devices to transport bulk-solid material for long distance. Dynamic analysis is the key to decide whether the design is rational in technique, safe and reliable in running, feasible in economy. It is very important to study dynamic properties, improve efficiency and productivity, guarantee conveyor safe, reliable and stable running. The dynamic researches and applications of large scale belt conveyor are discussed. The main research topics, the state-of-the-art of dynamic researches on belt conveyor are analyzed. The main future works focus on dynamic analysis, modeling and simulation of main components and whole system, nonlinear modeling, simulation and vibration analysis of large scale conveyor system.

RTL modeling with SystemVerilog for simulation and synthesis using SystemVerilog for ASIC and FPGA design

CERN Document Server

Sutherland, Stuart

2017-01-01

This book is both a tutorial and a reference for engineers who use the SystemVerilog Hardware Description Language (HDL) to design ASICs and FPGAs. The book shows how to write SystemVerilog models at the Register Transfer Level (RTL) that simulate and synthesize correctly, with a focus on proper coding styles and best practices. SystemVerilog is the latest generation of the original Verilog language, and adds many important capabilities to efficiently and more accurately model increasingly complex designs. This book reflects the SystemVerilog-2012/2017 standards. This book is for engineers who already know, or who are learning, digital design engineering. The book does not present digital design theory; it shows how to apply that theory to write RTL models that simulate and synthesize correctly. The creator of the original Verilog Language, Phil Moorby says about this book (an excerpt from the book's Foreword): “Many published textbooks on the design side of SystemVerilog assume that the reader is familiar ...

Using system dynamics simulation for assessment of hydropower system safety

Science.gov (United States)

King, L. M.; Simonovic, S. P.; Hartford, D. N. D.

2017-08-01

Hydropower infrastructure systems are complex, high consequence structures which must be operated safely to avoid catastrophic impacts to human life, the environment, and the economy. Dam safety practitioners must have an in-depth understanding of how these systems function under various operating conditions in order to ensure the appropriate measures are taken to reduce system vulnerability. Simulation of system operating conditions allows modelers to investigate system performance from the beginning of an undesirable event to full system recovery. System dynamics simulation facilitates the modeling of dynamic interactions among complex arrangements of system components, providing outputs of system performance that can be used to quantify safety. This paper presents the framework for a modeling approach that can be used to simulate a range of potential operating conditions for a hydropower infrastructure system. Details of the generic hydropower infrastructure system simulation model are provided. A case study is used to evaluate system outcomes in response to a particular earthquake scenario, with two system safety performance measures shown. Results indicate that the simulation model is able to estimate potential measures of system safety which relate to flow conveyance and flow retention. A comparison of operational and upgrade strategies is shown to demonstrate the utility of the model for comparing various operational response strategies, capital upgrade alternatives, and maintenance regimes. Results show that seismic upgrades to the spillway gates provide the largest improvement in system performance for the system and scenario of interest.

AEGIS geologic simulation model

International Nuclear Information System (INIS)

Foley, M.G.

1982-01-01

The Geologic Simulation Model (GSM) is used by the AEGIS (Assessment of Effectiveness of Geologic Isolation Systems) program at the Pacific Northwest Laboratory to simulate the dynamic geology and hydrology of a geologic nuclear waste repository site over a million-year period following repository closure. The GSM helps to organize geologic/hydrologic data; to focus attention on active natural processes by requiring their simulation; and, through interactive simulation and calibration, to reduce subjective evaluations of the geologic system. During each computer run, the GSM produces a million-year geologic history that is possible for the region and the repository site. In addition, the GSM records in permanent history files everything that occurred during that time span. Statistical analyses of data in the history files of several hundred simulations are used to classify typical evolutionary paths, to establish the probabilities associated with deviations from the typical paths, and to determine which types of perturbations of the geologic/hydrologic system, if any, are most likely to occur. These simulations will be evaluated by geologists familiar with the repository region to determine validity of the results. Perturbed systems that are determined to be the most realistic, within whatever probability limits are established, will be used for the analyses that involve radionuclide transport and dose models. The GSM is designed to be continuously refined and updated. Simulation models are site specific, and, although the submodels may have limited general applicability, the input data equirements necessitate detailed characterization of each site before application

Use case driven approach to develop simulation model for PCS of APR1400 simulator

International Nuclear Information System (INIS)

Dong Wook, Kim; Hong Soo, Kim; Hyeon Tae, Kang; Byung Hwan, Bae

2006-01-01

The full-scope simulator is being developed to evaluate specific design feature and to support the iterative design and validation in the Man-Machine Interface System (MMIS) design of Advanced Power Reactor (APR) 1400. The simulator consists of process model, control logic model, and MMI for the APR1400 as well as the Power Control System (PCS). In this paper, a use case driven approach is proposed to develop a simulation model for PCS. In this approach, a system is considered from the point of view of its users. User's view of the system is based on interactions with the system and the resultant responses. In use case driven approach, we initially consider the system as a black box and look at its interactions with the users. From these interactions, use cases of the system are identified. Then the system is modeled using these use cases as functions. Lower levels expand the functionalities of each of these use cases. Hence, starting from the topmost level view of the system, we proceeded down to the lowest level (the internal view of the system). The model of the system thus developed is use case driven. This paper will introduce the functionality of the PCS simulation model, including a requirement analysis based on use case and the validation result of development of PCS model. The PCS simulation model using use case will be first used during the full-scope simulator development for nuclear power plant and will be supplied to Shin-Kori 3 and 4 plant. The use case based simulation model development can be useful for the design and implementation of simulation models. (authors)

Modeling and simulation of the feedwater system, associated controller and interface with the user for the SUN-RAH nucleo electric plants university student simulator

International Nuclear Information System (INIS)

Sanchez B, A.

2003-01-01

The simulation process of the component systems of the feedwater of a nucleo electric plant is presented, using several models of reduced order that represent the diverse elements that compose the systems like: the heaters of feedwater, the condenser, the feedwater pump, etc. The integration of the same ones in one simulative structure, and the development of a platform that to give the appearance of to be executed in continuous time, it is the objective of the feedwater simulator, as well as of the SUN-RAH simulator, of which is part. The simulator uses models of reduced order that respond to the observed behavior of a nuclear plant of BWR type. Likewise, it is presented a model of a flow controller of feedwater that will be the one in charge of regulating the demand of the system according to the characteristics and criticize restrictions of safety and controllability, assigned according to those wanted parameters of performance of this system inside the nucleo electric plant. The integration of these models, the adaptation of the variables and parameters, are presented in a way that the integration with the other ones models of the remaining systems of the plant (reactor, steam lines, turbine, etc.), be direct and coherent with the principles of thermodynamic cycles relative to this type of generation plants. The design of those graphic interfaces and the environment where the simulator works its are part of those developments of this work. The reaches and objectives of the simulator complement the description of the simulator. (Author)

A Dynamic Simulation Model of the Management Accounting Information Systems (MAIS)

Science.gov (United States)

Konstantopoulos, Nikolaos; Bekiaris, Michail G.; Zounta, Stella

2007-12-01

The aim of this paper is to examine the factors which determine the problems and the advantages on the design of management accounting information systems (MAIS). A simulation is carried out with a dynamic model of the MAIS design.

Improvements to information management systems simulator

Science.gov (United States)

Bilek, R. W.

1972-01-01

The performance of personnel in the augmentation and improvement of the interactive IMSIM information management simulation model is summarized. With this augmented model, NASA now has even greater capabilities for the simulation of computer system configurations, data processing loads imposed on these configurations, and executive software to control system operations. Through these simulations, NASA has an extremely cost effective capability for the design and analysis of computer-based data management systems.

A simulation model for material accounting systems

International Nuclear Information System (INIS)

Coulter, C.A.; Thomas, K.E.

1987-01-01

A general-purpose model that was developed to simulate the operation of a chemical processing facility for nuclear materials has been extended to describe material measurement and accounting procedures as well. The model now provides descriptors for material balance areas, a large class of measurement instrument types and their associated measurement errors for various classes of materials, the measurement instruments themselves with their individual calibration schedules, and material balance closures. Delayed receipt of measurement results (as for off-line analytical chemistry assay), with interim use of a provisional measurement value, can be accurately represented. The simulation model can be used to estimate inventory difference variances for processing areas that do not operate at steady state, to evaluate the timeliness of measurement information, to determine process impacts of measurement requirements, and to evaluate the effectiveness of diversion-detection algorithms. Such information is usually difficult to obtain by other means. Use of the measurement simulation model is illustrated by applying it to estimate inventory difference variances for two material balance area structures of a fictitious nuclear material processing line

Description of waste pretreatment and interfacing systems dynamic simulation model

International Nuclear Information System (INIS)

Garbrick, D.J.; Zimmerman, B.D.

1995-05-01

The Waste Pretreatment and Interfacing Systems Dynamic Simulation Model was created to investigate the required pretreatment facility processing rates for both high level and low level waste so that the vitrification of tank waste can be completed according to the milestones defined in the Tri-Party Agreement (TPA). In order to achieve this objective, the processes upstream and downstream of the pretreatment facilities must also be included. The simulation model starts with retrieval of tank waste and ends with vitrification for both low level and high level wastes. This report describes the results of three simulation cases: one based on suggested average facility processing rates, one with facility rates determined so that approximately 6 new DSTs are required, and one with facility rates determined so that approximately no new DSTs are required. It appears, based on the simulation results, that reasonable facility processing rates can be selected so that no new DSTs are required by the TWRS program. However, this conclusion must be viewed with respect to the modeling assumptions, described in detail in the report. Also included in the report, in an appendix, are results of two sensitivity cases: one with glass plant water recycle steams recycled versus not recycled, and one employing the TPA SST retrieval schedule versus a more uniform SST retrieval schedule. Both recycling and retrieval schedule appear to have a significant impact on overall tank usage

Research on support effectiveness modeling and simulating of aviation materiel autonomic logistics system

Science.gov (United States)

Zhou, Yan; Zhou, Yang; Yuan, Kai; Jia, Zhiyu; Li, Shuo

2018-05-01

Aiming at the demonstration of autonomic logistics system to be used at the new generation of aviation materiel in our country, the modeling and simulating method of aviation materiel support effectiveness considering autonomic logistics are studied. Firstly, this paper introduced the idea of JSF autonomic logistics and analyzed the influence of autonomic logistics on support effectiveness from aspects of reliability, false alarm rate, troubleshooting time, and support delay time and maintenance level. On this basis, the paper studies the modeling and simulating methods of support effectiveness considering autonomic logistics, and puts forward the maintenance support simulation process considering autonomic logistics. Finally, taking the typical aviation materiel as an example, this paper analyzes and verifies the above-mentioned support effectiveness modeling and simulating method of aviation materiel considering autonomic logistics.

Automated Simulation Model Generation

NARCIS (Netherlands)

Huang, Y.

2013-01-01

One of today's challenges in the field of modeling and simulation is to model increasingly larger and more complex systems. Complex models take long to develop and incur high costs. With the advances in data collection technologies and more popular use of computer-aided systems, more data has become

Stochastic modeling and simulation of reaction-diffusion system with Hill function dynamics.

Science.gov (United States)

Chen, Minghan; Li, Fei; Wang, Shuo; Cao, Young

2017-03-14

Stochastic simulation of reaction-diffusion systems presents great challenges for spatiotemporal biological modeling and simulation. One widely used framework for stochastic simulation of reaction-diffusion systems is reaction diffusion master equation (RDME). Previous studies have discovered that for the RDME, when discretization size approaches zero, reaction time for bimolecular reactions in high dimensional domains tends to infinity. In this paper, we demonstrate that in the 1D domain, highly nonlinear reaction dynamics given by Hill function may also have dramatic change when discretization size is smaller than a critical value. Moreover, we discuss methods to avoid this problem: smoothing over space, fixed length smoothing over space and a hybrid method. Our analysis reveals that the switch-like Hill dynamics reduces to a linear function of discretization size when the discretization size is small enough. The three proposed methods could correctly (under certain precision) simulate Hill function dynamics in the microscopic RDME system.

A VRLA battery simulation model

International Nuclear Information System (INIS)

Pascoe, Phillip E.; Anbuky, Adnan H.

2004-01-01

A valve regulated lead acid (VRLA) battery simulation model is an invaluable tool for the standby power system engineer. The obvious use for such a model is to allow the assessment of battery performance. This may involve determining the influence of cells suffering from state of health (SOH) degradation on the performance of the entire string, or the running of test scenarios to ascertain the most suitable battery size for the application. In addition, it enables the engineer to assess the performance of the overall power system. This includes, for example, running test scenarios to determine the benefits of various load shedding schemes. It also allows the assessment of other power system components, either for determining their requirements and/or vulnerabilities. Finally, a VRLA battery simulation model is vital as a stand alone tool for educational purposes. Despite the fundamentals of the VRLA battery having been established for over 100 years, its operating behaviour is often poorly understood. An accurate simulation model enables the engineer to gain a better understanding of VRLA battery behaviour. A system level multipurpose VRLA battery simulation model is presented. It allows an arbitrary battery (capacity, SOH, number of cells and number of strings) to be simulated under arbitrary operating conditions (discharge rate, ambient temperature, end voltage, charge rate and initial state of charge). The model accurately reflects the VRLA battery discharge and recharge behaviour. This includes the complex start of discharge region known as the coup de fouet

Atmospheric models in the numerical simulation system (SPEEDI-MP) for environmental studies

International Nuclear Information System (INIS)

Nagai, Haruyasu; Terada, Hiroaki

2007-01-01

As a nuclear emergency response system, numerical models to predict the atmospheric dispersion of radionuclides have been developed at Japan Atomic Energy Agency (JAEA). Evolving these models by incorporating new schemes for physical processes and up-to-date computational technologies, a numerical simulation system, which consists of dynamical models and material transport models for the atmospheric, terrestrial, and oceanic environments, has been constructed to apply for various environmental studies. In this system, the combination of a non-hydrostatic atmospheric dynamic model and Lagrangian particle dispersion model is used for the emergency response system. The utilization of detailed meteorological field by the atmospheric model improves the model performance for diffusion and deposition calculations. It also calculates a large area domain with coarse resolution and local area domain with high resolution simultaneously. The performance of new model system was evaluated using measurements of surface deposition of 137 Cs over Europe during the Chernobyl accident. (author)

Simulation bounds for system availability

International Nuclear Information System (INIS)

Tietjen, G.L.; Waller, R.A.

1976-01-01

System availability is a dominant factor in the practicality of nuclear power electrical generating plants. A proposed model for obtaining either lower bounds or interval estimates on availability uses observed data on ''n'' failure-to-repair cycles of the system to estimate the parameters in the time-to-failure and time-to-repair models. These estimates are then used in simulating failure/repair cycles of the system. The availability estimate is obtained for each of 5000 samples of ''n'' failure/repair cycles to form a distribution of estimates. Specific percentile points of those simulated distributions are selected as lower simulation bounds or simulation interval bounds for the system availability. The method is illustrated with operational data from two nuclear plants for which an exponential time-to-failure and a lognormal time-to-repair are assumed

Development of AC-DC power system simulator

International Nuclear Information System (INIS)

Ichikawa, Tatsumi; Ueda, Kiyotaka; Inoue, Toshio

1984-01-01

A modeling and realization technique is described for realtime plant dynamics simulation of nuclear power generating unit in AC-DC power system simulator. Dynamic behavior of reactor system and steam system is important for investigation a further adequate unit control and protection system to system faults in AC and DC power system. Each unit of two nuclear power generating unit in the power system simulator consists of micro generator, DC motors, flywheels and process computer. The DC motor and flywheel simulates dynamic characteristics of steam turbine, and process computer simulates plant dynamics by digital simulation. We have realized real-time plant dynamics simulation by utilizing a high speed process I/O and a high speed digital differential analyzing processor (DDA) in which we builted a newly developed simple plant model. (author)

Piloted Simulation of a Model-Predictive Automated Recovery System

Science.gov (United States)

Liu, James (Yuan); Litt, Jonathan; Sowers, T. Shane; Owens, A. Karl; Guo, Ten-Huei

2014-01-01

This presentation describes a model-predictive automatic recovery system for aircraft on the verge of a loss-of-control situation. The system determines when it must intervene to prevent an imminent accident, resulting from a poor approach. It estimates the altitude loss that would result from a go-around maneuver at the current flight condition. If the loss is projected to violate a minimum altitude threshold, the maneuver is automatically triggered. The system deactivates to allow landing once several criteria are met. Piloted flight simulator evaluation showed the system to provide effective envelope protection during extremely unsafe landing attempts. The results demonstrate how flight and propulsion control can be integrated to recover control of the vehicle automatically and prevent a potential catastrophe.

Modelation and simulation of technical systems. An introduction close to practice; Modellierung und Simulation technischer Systeme. Eine praxisnahe Einfuehrung

Energy Technology Data Exchange (ETDEWEB)

Nollau, Reiner [HAWK Hochschule fuer Angewandte Wissenschaft und Kunst - FH Hildesheim/Holzminden/Goettingen, Goettingen (Germany). Fakultaet Naturwissenschaften und Technik

2009-07-01

There is a growing trend towards using calculation programmes to design and optimise technical systems. Such programmes simulate the systems' dynamic behaviour on the basis of mathematical models. This book first presents the methods used for model identification and model description. A widely applicable basic algorithm has been derived by means of these methods. Creating an overview block diagram of the system under study constitutes an important step of model development. The methods elaborated by the author are applied to numerous examples ordered in a sequence of growing complexity and hence difficulty. The examples each end with calculations on the model's behaviour, the results of which the reader can verify. Using the applied basic algorithm as a basis the reader can efficiently examine other systems not addressed in the book. [German] Technische Systeme werden immer staerker mit Hilfe von Rechnerprogrammen entworfen und optimiert. Die Programme simulieren das dynamische Verhalten der Systeme auf der Basis von mathematischen Modellen. In diesem Buch wird zunaechst die Methodik der Modellermittlung und -beschreibung dargelegt, aus welcher ein breit anwendbarer Grundalgorithmus abgeleitet worden ist. Eine wichtige Stufe der Modellentwicklung ist das Gesamt-Blockschaltbild des untersuchten Systems. Die vom Autor erarbeitete Methodik wird auf zahlreiche Beispiele wachsender Komplexitaet und damit wachsenden Schwierigkeitsgrades angewendet. Diese Beispiele enden mit Berechnungen des Verhaltens dieser Modelle, deren Ergebnisse der Leser nachpruefen kann. Der Leser kann auf der Grundlage des angewendeten Grundalgorithmus zielstrebig andere, im Buch nicht behandelte, Systeme untersuchen. (orig.)

Method and Tool for Design Process Navigation and Automatic Generation of Simulation Models for Manufacturing Systems

Science.gov (United States)

Nakano, Masaru; Kubota, Fumiko; Inamori, Yutaka; Mitsuyuki, Keiji

Manufacturing system designers should concentrate on designing and planning manufacturing systems instead of spending their efforts on creating the simulation models to verify the design. This paper proposes a method and its tool to navigate the designers through the engineering process and generate the simulation model automatically from the design results. The design agent also supports collaborative design projects among different companies or divisions with distributed engineering and distributed simulation techniques. The idea was implemented and applied to a factory planning process.

Nuclear fuel cycle system simulation tool based on high-fidelity component modeling

Energy Technology Data Exchange (ETDEWEB)

Ames, David E.,

2014-02-01

The DOE is currently directing extensive research into developing fuel cycle technologies that will enable the safe, secure, economic, and sustainable expansion of nuclear energy. The task is formidable considering the numerous fuel cycle options, the large dynamic systems that each represent, and the necessity to accurately predict their behavior. The path to successfully develop and implement an advanced fuel cycle is highly dependent on the modeling capabilities and simulation tools available for performing useful relevant analysis to assist stakeholders in decision making. Therefore a high-fidelity fuel cycle simulation tool that performs system analysis, including uncertainty quantification and optimization was developed. The resulting simulator also includes the capability to calculate environmental impact measures for individual components and the system. An integrated system method and analysis approach that provides consistent and comprehensive evaluations of advanced fuel cycles was developed. A general approach was utilized allowing for the system to be modified in order to provide analysis for other systems with similar attributes. By utilizing this approach, the framework for simulating many different fuel cycle options is provided. Two example fuel cycle configurations were developed to take advantage of used fuel recycling and transmutation capabilities in waste management scenarios leading to minimized waste inventories.

Simulation model of a PWR power plant

International Nuclear Information System (INIS)

Larsen, N.

1987-03-01

A simulation model of a hypothetical PWR power plant is described. A large number of disturbances and failures in plant function can be simulated. The model is written as seven modules to the modular simulation system for continuous processes DYSIM and serves also as a user example of this system. The model runs in Fortran 77 on the IBM-PC-AT. (author)

OPNET Modeler simulations of performance for multi nodes wireless systems

Directory of Open Access Journals (Sweden)

Krupanek Beata

2016-01-01

Full Text Available Paper presents a study under the Quality of Service in modern wireless sensor networks. Such a networks are characterized by small amount of data transmitted in fixed periods. Very often this data must by transmitted in real time so data transmission delays should be well known. This article shows multimode network simulated in packet OPNET Modeler. Also nowadays the quality of services is very important especially in multi-nodes systems such a home automation or measurement systems.

Interactive Simulations of Biohybrid Systems

Directory of Open Access Journals (Sweden)

Sebastian Albrecht von Mammen

2017-10-01

Full Text Available In this article, we present approaches to interactive simulations of biohybrid systems. These simulations are comprised of two major computational components: (1 agent-based developmental models that retrace organismal growth and unfolding of technical scaffoldings and (2 interfaces to explore these models interactively. Simulations of biohybrid systems allow us to fast forward and experience their evolution over time based on our design decisions involving the choice, configuration and initial states of the deployed biological and robotic actors as well as their interplay with the environment. We briefly introduce the concept of swarm grammars, an agent-based extension of L-systems for retracing growth processes and structural artifacts. Next, we review an early augmented reality prototype for designing and projecting biohybrid system simulations into real space. In addition to models that retrace plant behaviors, we specify swarm grammar agents to braid structures in a self-organizing manner. Based on this model, both robotic and plant-driven braiding processes can be experienced and explored in virtual worlds. We present an according user interface for use in virtual reality. As we present interactive models concerning rather diverse description levels, we only ensured their principal capacity for interaction but did not consider efficiency analyzes beyond prototypic operation. We conclude this article with an outlook on future works on melding reality and virtuality to drive the design and deployment of biohybrid systems.

Innovative Calibration Method for System Level Simulation Models of Internal Combustion Engines

Directory of Open Access Journals (Sweden)

Ivo Prah

2016-09-01

Full Text Available The paper outlines a procedure for the computer-controlled calibration of the combined zero-dimensional (0D and one-dimensional (1D thermodynamic simulation model of a turbocharged internal combustion engine (ICE. The main purpose of the calibration is to determine input parameters of the simulation model in such a way as to achieve the smallest difference between the results of the measurements and the results of the numerical simulations with minimum consumption of the computing time. An innovative calibration methodology is based on a novel interaction between optimization methods and physically based methods of the selected ICE sub-systems. Therein physically based methods were used for steering the division of the integral ICE to several sub-models and for determining parameters of selected components considering their governing equations. Innovative multistage interaction between optimization methods and physically based methods allows, unlike the use of well-established methods that rely only on the optimization techniques, for successful calibration of a large number of input parameters with low time consumption. Therefore, the proposed method is suitable for efficient calibration of simulation models of advanced ICEs.

Sparse identification of a predator-prey system from simulation data of a convection model

DEFF Research Database (Denmark)

Dam, Magnus; Brøns, Morten; Rasmussen, Jens Juul

2017-01-01

of a convection problem. A convection model with a pressure source centered at the inner boundary models the edge dynamics of a magnetically confined plasma. The convection problem undergoes a sequence of bifurcations as the strength of the pressure source increases. The time evolution of the energies......The use of low-dimensional dynamical systems as reduced models for plasma dynamics is useful as solving an initial value problem requires much less computational resources than fluid simulations. We utilize a data-driven modeling approach to identify a reduced model from simulation data...

Modelling and simulation of wood chip combustion in a hot air generator system.

Science.gov (United States)

Rajika, J K A T; Narayana, Mahinsasa

2016-01-01

This study focuses on modelling and simulation of horizontal moving bed/grate wood chip combustor. A standalone finite volume based 2-D steady state Euler-Euler Computational Fluid Dynamics (CFD) model was developed for packed bed combustion. Packed bed combustion of a medium scale biomass combustor, which was retrofitted from wood log to wood chip feeding for Tea drying in Sri Lanka, was evaluated by a CFD simulation study. The model was validated by the experimental results of an industrial biomass combustor for a hot air generation system in tea industry. Open-source CFD tool; OpenFOAM was used to generate CFD model source code for the packed bed combustion and simulated along with an available solver for free board region modelling in the CFD tool. Height of the packed bed is about 20 cm and biomass particles are assumed to be spherical shape with constant surface area to volume ratio. Temperature measurements of the combustor are well agreed with simulation results while gas phase compositions have discrepancies. Combustion efficiency of the validated hot air generator is around 52.2 %.

Simulation and tests to individual and coupled models of the reactor vessel simulator and the recirculation system for the SUN-RAH

International Nuclear Information System (INIS)

Sanchez S, R.A.

2004-01-01

The present project, is continuation of the project presented in the congress SNM-2003. In this new phase of the project, they were carried out adaptive changes to the modeling and implementation of the module of the full superior of the core of the reactor, they were carried out those modeling of the generation of heat as well as of the energy transfer in the one fuel. These models present the main characteristics of the vessel of the one reactor and of the recirculation system, defined by the main phenomena that they intervene in the physical processes, in the previous version the simulation in real time it required of an extremely quick computer and without executing collateral processes. The tests are presented carried out to the different models belonging to the Simulator of the Reactor Vessel and the Recirculation system for the SUN-RAH (University Simulator of Nucleo electric with Boiling Water Reactor), as well as the results hurtled by this tests. In each section the executions of the tests and the corresponding analyses of results are shown for each pattern. Besides the above mentioned, the advantages presented by the Simulator of the reactor vessel and the recirculation system are pointed. (Author)

Validation of a simultaneous PET/MR system model for PET simulation using GATE

International Nuclear Information System (INIS)

Monnier, Florian; Fayad, Hadi; Bert, Julien; Schmidt, Holger; Visvikis, Dimitris

2015-01-01

Simultaneous PET/MR acquisition shows promise in a range of applications. Simulation using GATE is an essential tool that allows obtaining the ground truth for such acquisitions and therefore helping in the development and the validation of innovative processing methods such as PET image reconstruction, attenuation correction and motion correction. The purpose of this work is to validate the GATE simulation of the Siemens Biograph mMR PET/MR system. A model of the Siemens Biograph mMR was developed. This model includes the geometry and spatial positioning of the crystals inside the scanner and the characteristics of the detection process. The accuracy of the model was tested by comparing, on a real physical phantom study, GATE simulated results to reconstructed PET images using measured results obtained from a Siemens Biograph mMR system. The same parameters such as the acquisition time and phantom position inside the scanner were fixed for our simulations. List-mode outputs were recovered in both cases and reconstructed using the OPL-EM algorithm. Several parameters were used to compare the two reconstructed images such as profile comparison, signal-to-noise ratio and activity contrast analysis. Finally patient acquired MR images were segmented and used for the simulation of corresponding PET images. The simulated and acquired sets of reconstructed phantom images showed close emission values in regions of interest with relative differences lower than 5%. The scatter fraction was within a <3% agreement. Close matching of profiles and contrast indices were obtained between simulated and corresponding acquired PET images. Our results indicate that the GATE developed Biograph mMR model is accurate in comparison to the real scanner performance and can be used for evaluating innovative processing methods for applications in clinical PET/MR protocols.

Bourbaki's structure theory in the problem of complex systems simulation models synthesis and model-oriented programming

Science.gov (United States)

Brodsky, Yu. I.

2015-01-01

The work is devoted to the application of Bourbaki's structure theory to substantiate the synthesis of simulation models of complex multicomponent systems, where every component may be a complex system itself. An application of the Bourbaki's structure theory offers a new approach to the design and computer implementation of simulation models of complex multicomponent systems—model synthesis and model-oriented programming. It differs from the traditional object-oriented approach. The central concept of this new approach and at the same time, the basic building block for the construction of more complex structures is the concept of models-components. A model-component endowed with a more complicated structure than, for example, the object in the object-oriented analysis. This structure provides to the model-component an independent behavior-the ability of standard responds to standard requests of its internal and external environment. At the same time, the computer implementation of model-component's behavior is invariant under the integration of models-components into complexes. This fact allows one firstly to construct fractal models of any complexity, and secondly to implement a computational process of such constructions uniformly-by a single universal program. In addition, the proposed paradigm allows one to exclude imperative programming and to generate computer code with a high degree of parallelism.

Generalized DSS shell for developing simulation and optimization hydro-economic models of complex water resources systems

Science.gov (United States)

Pulido-Velazquez, Manuel; Lopez-Nicolas, Antonio; Harou, Julien J.; Andreu, Joaquin

2013-04-01

Hydrologic-economic models allow integrated analysis of water supply, demand and infrastructure management at the river basin scale. These models simultaneously analyze engineering, hydrology and economic aspects of water resources management. Two new tools have been designed to develop models within this approach: a simulation tool (SIM_GAMS), for models in which water is allocated each month based on supply priorities to competing uses and system operating rules, and an optimization tool (OPT_GAMS), in which water resources are allocated optimally following economic criteria. The characterization of the water resource network system requires a connectivity matrix representing the topology of the elements, generated using HydroPlatform. HydroPlatform, an open-source software platform for network (node-link) models, allows to store, display and export all information needed to characterize the system. Two generic non-linear models have been programmed in GAMS to use the inputs from HydroPlatform in simulation and optimization models. The simulation model allocates water resources on a monthly basis, according to different targets (demands, storage, environmental flows, hydropower production, etc.), priorities and other system operating rules (such as reservoir operating rules). The optimization model's objective function is designed so that the system meets operational targets (ranked according to priorities) each month while following system operating rules. This function is analogous to the one used in the simulation module of the DSS AQUATOOL. Each element of the system has its own contribution to the objective function through unit cost coefficients that preserve the relative priority rank and the system operating rules. The model incorporates groundwater and stream-aquifer interaction (allowing conjunctive use simulation) with a wide range of modeling options, from lumped and analytical approaches to parameter-distributed models (eigenvalue approach). Such

Improved simulation of tropospheric ozone by a global-multi-regional two-way coupling model system

Directory of Open Access Journals (Sweden)

Y. Yan

2016-02-01

Full Text Available Small-scale nonlinear chemical and physical processes over pollution source regions affect the tropospheric ozone (O3, but these processes are not captured by current global chemical transport models (CTMs and chemistry–climate models that are limited by coarse horizontal resolutions (100–500 km, typically 200 km. These models tend to contain large (and mostly positive tropospheric O3 biases in the Northern Hemisphere. Here we use the recently built two-way coupling system of the GEOS-Chem CTM to simulate the regional and global tropospheric O3 in 2009. The system couples the global model (at 2.5° long.  ×  2° lat. and its three nested models (at 0.667° long.  ×  0.5° lat. covering Asia, North America and Europe, respectively. Specifically, the nested models take lateral boundary conditions (LBCs from the global model, better capture small-scale processes and feed back to modify the global model simulation within the nested domains, with a subsequent effect on their LBCs. Compared to the global model alone, the two-way coupled system better simulates the tropospheric O3 both within and outside the nested domains, as found by evaluation against a suite of ground (1420 sites from the World Data Centre for Greenhouse Gases (WDCGG, the United States National Oceanic and Atmospheric Administration (NOAA Earth System Research Laboratory Global Monitoring Division (GMD, the Chemical Coordination Centre of European Monitoring and Evaluation Programme (EMEP, and the United States Environmental Protection Agency Air Quality System (AQS, aircraft (the High-performance Instrumented Airborne Platform for Environmental Research (HIAPER Pole-to-Pole Observations (HIPPO and Measurement of Ozone and Water Vapor by Airbus In- Service Aircraft (MOZAIC and satellite measurements (two Ozone Monitoring Instrument (OMI products. The two-way coupled simulation enhances the correlation in day-to-day variation of afternoon mean surface O3

Modeling and simulation of grid connected permanent magnet generator based small wind energy conversion systems

Energy Technology Data Exchange (ETDEWEB)

Arifujjaman, Md.

2011-07-01

In order to recover the maximum energy from small scale wind turbine systems many parameters have to be controlled. The aim of this paper is to propose a control strategy for the grid connected PMG-based small wind turbine systems. A mathematical model of small wind turbine systems was developed and the system simulated. Results show demonstrated that the control strategy is highly efficient. Sure enough it reduces the dependence on system variables, diminishes the system complexity, its furling and maximum power point controllers are efficient and it provides a stable operation for multiple wind speeds. This study developed a modeling and control strategy which was proved to be feasible by simulation results.

Simulation model for wind energy storage systems. Volume II. Operation manual. [SIMWEST code

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume II, the SIMWEST operation manual, describes the usage of the SIMWEST program, the design of the library components, and a number of simple example simulations intended to familiarize the user with the program's operation. Volume II also contains a listing of each SIMWEST library subroutine.

Nuclear facility safeguards systems modeling using discrete event simulation

International Nuclear Information System (INIS)

Engi, D.

1977-01-01

The threat of theft or dispersal of special nuclear material at a nuclear facility is treated by studying the temporal relationships between adversaries having authorized access to the facility (insiders) and safeguards system events by using a GASP IV discrete event simulation. The safeguards system events--detection, assessment, delay, communications, and neutralization--are modeled for the general insider adversary strategy which includes degradation of the safeguards system elements followed by an attempt to steal or disperse special nuclear material. The performance measure used in the analysis is the estimated probability of safeguards system success in countering the adversary based upon a predetermined set of adversary actions. An exemplary problem which includes generated results is presented for a hypothetical nuclear facility. The results illustrate representative information that could be utilized by safeguards decision-makers

Development of a selection support expert system of mathematical models for dynamic simulation of liquid-vapor two-phase flow

International Nuclear Information System (INIS)

Gofuku, Akio; Shimizu, Kenji; Sugano, Keiji; Morimoto, Takashi; Yoshikawa, Hidekazu; Wakabayashi, Jiro

1992-01-01

This paper deals with computerized supporting techniques of a numerical simulation of complex and large-scale engineering systems like nuclear power plants. As an example of the intelligent support systems of dynamic simulation, a prototype expert system is developed on an expert system development tool to support the selection of mathematical model which is a first step of numerical simulation and is required both wide expert knowledge and high-level decision making. The expert system supports the selection of liquid-vapor two phase flow models (fluid model and constitutive equations) consistent with simulation purpose and condition in the case of thermal-hydraulic simulation of nuclear power plants. The possibility of the expert system is examined for various selection support cases by both investigation of the appropriateness of the selection support logic and comparison between support results and decision results of several experts. (author)

Transportation system modeling and simulation in support of logistics and operations

International Nuclear Information System (INIS)

Yoshimura, R.H.; Kjeldgaard, E.A.; Turnquist, M.A.; List, G.F.

1997-12-01

Effective management of DOE's transportation operations requires better data than are currently available, a more integrated management structure for making transportation decisions, and decision support tools to provide needed analysis capabilities. This paper describes a vision of an advanced logistics management system for DOE, and the rationale for developing improved modeling and simulation capability as an integral part of that system. The authors illustrate useful types of models through four examples, addressing issues of transportation package allocation, fleet sizing, routing/scheduling, and emergency responder location. The overall vision for the advanced logistics management system, and the specific examples of potential capabilities, provide the basis for a conclusion that such a system would meet a critical DOE need in the area of radioactive material and waste transportation

Transportation system modeling and simulation in support of logistics and operations

International Nuclear Information System (INIS)

Yoshimura, R.H.; Kjeldgaard, E.A.; Turnquist, M.A.; List, G.F.

1998-01-01

Effective management of DOE's transportation operations requires better data than are currently available, a more integrated management structure for making transportation decisions, and decision support tools to provide needed analysis capabilities. This paper describes a vision of an advanced logistics management system for DOE, and the rationale for developing improved modeling and simulation capability as an integral part of that system. We illustrate useful types of models through four examples, addressing issues of transportation package allocation, fleet sizing, routing/Scheduling, and emergency responder location. The overall vision for the advanced logistics management system, and the specific examples of potential capabilities, provide the basis for a conclusion that such a system would meet a critical DOE need in the area of radioactive material and waste transportation. (authors)

JACOS: AI-based simulation system for man-machine system behavior in NPP

International Nuclear Information System (INIS)

Yoshida, Kazuo; Yokobayashi, Masao; Tanabe, Fumiya; Komiya, Akitoshi

2001-08-01

A prototype of a computer simulation system named JACOS (JAERI COgnitive Simulation system) has been developed at JAERI (Japan Atomic Energy Research Institute) to simulate the man-machine system behavior in which both the cognitive behavior of a human operator and the plant behavior affect each other. The objectives of this system development is to provide man-machine system analysts with detailed information on the cognitive process of an operator and the plant behavior affected by operator's actions in accidental situations of a nuclear power plant. The simulation system consists of an operator model and a plant model which are coupled dynamically. The operator model simulates an operator's cognitive behavior in accidental situations based on the decision ladder model of Rasmussen, and is implemented using the AI-techniques of the distributed cooperative inference method with the so-called blackboard architecture. Rule-based behavior is simulated using knowledge representation with If-Then type of rules. Knowledge-based behavior is simulated using knowledge representation with MFM (Multilevel Flow Modeling) and qualitative reasoning method. Cognitive characteristics of attentional narrowing, limitation of short-term memory, and knowledge recalling from long-term memory are also taken into account. The plant model of a 3-loop PWR is also developed using a best estimate thermal-hydraulic analysis code RELAP5/MOD2. This report is prepared as User's Manual for JACOS. The first chapter of this report describes both operator and plant models in detail. The second chapter includes instructive descriptions for program installation, building of a knowledge base for operator model, execution of simulation and analysis of simulation results. The examples of simulation with JACOS are shown in the third chapter. (author)

Assessment of effectiveness of Geologic Isolation Systems. The development and application of a geologic simulation model

International Nuclear Information System (INIS)

Foley, M.G.; Petrie, G.M.

1982-03-01

The Geologic Simulation Model (GSM) developed under the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) project at the Pacific Northwest Laboratory for the Department of Energy is a quasi-deterministic process-response model which simulates the development of the geologic and hydrologic systems of a ground-water basin for a million years into the future. Effects of natural processes on the ground-water hydrologic system are modeled principally by rate equations. The combined effects and synergistic interactions of different processes are approximated by linear superposition of their effects during discrete time intervals in a stepwise-integration approach. The completed AEGIS GSM was used to generate 500 Monte Carlo simulations of the behavior of the geologic/hydrologic system affecting a hypothetical repository in the Pasco Basin over the next million years. These simulations used data which were not subjected to a review adequate to the needs of a real site performance assessment. However, the general care used in generating the data, and the overall behavior of the GSM suggest that the results are plausible at this time

Full modelling of the MOSAIC animal PET system based on the GATE Monte Carlo simulation code

International Nuclear Information System (INIS)

Merheb, C; Petegnief, Y; Talbot, J N

2007-01-01

Positron emission tomography (PET) systems dedicated to animal imaging are now widely used for biological studies. The scanner performance strongly depends on the design and the characteristics of the system. Many parameters must be optimized like the dimensions and type of crystals, geometry and field-of-view (FOV), sampling, electronics, lightguide, shielding, etc. Monte Carlo modelling is a powerful tool to study the effect of each of these parameters on the basis of realistic simulated data. Performance assessment in terms of spatial resolution, count rates, scatter fraction and sensitivity is an important prerequisite before the model can be used instead of real data for a reliable description of the system response function or for optimization of reconstruction algorithms. The aim of this study is to model the performance of the Philips Mosaic(TM) animal PET system using a comprehensive PET simulation code in order to understand and describe the origin of important factors that influence image quality. We use GATE, a Monte Carlo simulation toolkit for a realistic description of the ring PET model, the detectors, shielding, cap, electronic processing and dead times. We incorporate new features to adjust signal processing to the Anger logic underlying the Mosaic(TM) system. Special attention was paid to dead time and energy spectra descriptions. Sorting of simulated events in a list mode format similar to the system outputs was developed to compare experimental and simulated sensitivity and scatter fractions for different energy thresholds using various models of phantoms describing rat and mouse geometries. Count rates were compared for both cylindrical homogeneous phantoms. Simulated spatial resolution was fitted to experimental data for 18 F point sources at different locations within the FOV with an analytical blurring function for electronic processing effects. Simulated and measured sensitivities differed by less than 3%, while scatter fractions agreed

Dynamic modelling and simulation of complex drive systems of large belt conveyors; Dynamische Modellierung und Simulation komplexer Antriebssysteme von Grossbandanlagen

Energy Technology Data Exchange (ETDEWEB)

Burgwinkel, Paul; Vreydal, Daniel; Eltaliawi, Gamil; Vijayakumar, Nandhakumar [RWTH Aachen (DE). Inst. fuer Maschinentechnik der Rohstoffindustrie (IMR)

2010-09-15

For the first time the Co-simulation method was successfully used for full representation of a large belt conveyor for an open cast mine in a simulation model at the Institute for Mechanical Engineering in the Raw Materials Industry at Rhineland-Westphalia Technological University in Aachen. The aim of this project was the development of an electro-mechanical simulation model, which represents all components of a large belt conveyor from the drive motor to the conveyor belt in one simulation model and thus makes the interactions between the individual assemblies verifiable by calculations. With the aid of the developed model it was possible to determine critical operating speeds of the represented large belt conveyor and derive suitable measures to combat undesirable resonance states in the drive assembly. Furthermore it was possible to clarify the advantage of the full numerical representation of an electromechanical drive system. (orig.)

Intraocular Telescopic System Design: Optical and Visual Simulation in a Human Eye Model.

Science.gov (United States)

Zoulinakis, Georgios; Ferrer-Blasco, Teresa

2017-01-01

Purpose. To design an intraocular telescopic system (ITS) for magnifying retinal image and to simulate its optical and visual performance after implantation in a human eye model. Methods. Design and simulation were carried out with a ray-tracing and optical design software. Two different ITS were designed, and their visual performance was simulated using the Liou-Brennan eye model. The difference between the ITS was their lenses' placement in the eye model and their powers. Ray tracing in both centered and decentered situations was carried out for both ITS while visual Strehl ratio (VSOTF) was computed using custom-made MATLAB code. Results. The results show that between 0.4 and 0.8 mm of decentration, the VSOTF does not change much either for far or near target distances. The image projection for these decentrations is in the parafoveal zone, and the quality of the image projected is quite similar. Conclusion. Both systems display similar quality while they differ in size; therefore, the choice between them would need to take into account specific parameters from the patient's eye. Quality does not change too much between 0.4 and 0.8 mm of decentration for either system which gives flexibility to the clinician to adjust decentration to avoid areas of retinal damage.

Modelling guidelines for core exit temperature simulations with system codes

Energy Technology Data Exchange (ETDEWEB)

Freixa, J., E-mail: jordi.freixa-terradas@upc.edu [Department of Physics and Nuclear Engineering, Technical University of Catalonia (UPC) (Spain); Paul Scherrer Institut (PSI), 5232 Villigen (Switzerland); Martínez-Quiroga, V., E-mail: victor.martinez@nortuen.com [Department of Physics and Nuclear Engineering, Technical University of Catalonia (UPC) (Spain); Zerkak, O., E-mail: omar.zerkak@psi.ch [Paul Scherrer Institut (PSI), 5232 Villigen (Switzerland); Reventós, F., E-mail: francesc.reventos@upc.edu [Department of Physics and Nuclear Engineering, Technical University of Catalonia (UPC) (Spain)

2015-05-15

Highlights: • Core exit temperature is used in PWRs as an indication of core heat up. • Modelling guidelines of CET response with system codes. • Modelling of heat transfer processes in the core and UP regions. - Abstract: Core exit temperature (CET) measurements play an important role in the sequence of actions under accidental conditions in pressurized water reactors (PWR). Given the difficulties in placing measurements in the core region, CET readings are used as criterion for the initiation of accident management (AM) procedures because they can indicate a core heat up scenario. However, the CET responses have some limitation in detecting inadequate core cooling and core uncovery simply because the measurement is not placed inside the core. Therefore, it is of main importance in the field of nuclear safety for PWR power plants to assess the capabilities of system codes for simulating the relation between the CET and the peak cladding temperature (PCT). The work presented in this paper intends to address this open question by making use of experimental work at integral test facilities (ITF) where experiments related to the evolution of the CET and the PCT during transient conditions have been carried out. In particular, simulations of two experiments performed at the ROSA/LSTF and PKL facilities are presented. The two experiments are part of a counterpart exercise between the OECD/NEA ROSA-2 and OECD/NEA PKL-2 projects. The simulations are used to derive guidelines in how to correctly reproduce the CET response during a core heat up scenario. Three aspects have been identified to be of main importance: (1) the need for a 3-dimensional representation of the core and Upper Plenum (UP) regions in order to model the heterogeneity of the power zones and axial areas, (2) the detailed representation of the active and passive heat structures, and (3) the use of simulated thermocouples instead of steam temperatures to represent the CET readings.

Modeling and Simulation Resource Repository (MSRR)(System Engineering/Integrated M&S Management Approach

Science.gov (United States)

Milroy, Audrey; Hale, Joe

2006-01-01

NASA s Exploration Systems Mission Directorate (ESMD) is implementing a management approach for modeling and simulation (M&S) that will provide decision-makers information on the model s fidelity, credibility, and quality, including the verification, validation and accreditation information. The NASA MSRR will be implemented leveraging M&S industry best practices. This presentation will discuss the requirements that will enable NASA to capture and make available the "meta data" or "simulation biography" data associated with a model. The presentation will also describe the requirements that drive how NASA will collect and document relevant information for models or suites of models in order to facilitate use and reuse of relevant models and provide visibility across NASA organizations and the larger M&S community.

Immune system simulation online

DEFF Research Database (Denmark)

Rapin, Nicolas; Lund, Ole; Castiglione, Filippo

2011-01-01

MOTIVATION: The recognition of antigenic peptides is a major event of an immune response. In current mesoscopic-scale simulators of the immune system, this crucial step has been modeled in a very approximated way. RESULTS: We have equipped an agent-based model of the immune system with immuno...

Modeling and Simulation for an 8 kW Three-Phase Grid-Connected Photo-Voltaic Power System

Science.gov (United States)

Cen, Zhaohui

2017-09-01

Gird-connected Photo-Voltaic (PV) systems rated as 5-10 kW level have advantages of scalability and energy-saving, so they are very typical for small-scale household solar applications. In this paper, an 8 kW three-phase grid-connected PV system model is proposed and studied. In this high-fidelity model, some basic PV system components such as solar panels, DC-DC converters, DC-AC inverters and three-phase utility grids are mathematically modelled and organized as a complete simulation model. Also, an overall power controller with Maximum Power Point Control (MPPT) is proposed to achieve both high-efficiency for solar energy harvesting and grid-connection stability. Finally, simulation results demonstrate the effectiveness of the PV system model and the proposed controller, and power quality issues are discussed.

Modeling and Simulation for an 8 kW Three-Phase Grid-Connected Photo-Voltaic Power System

Directory of Open Access Journals (Sweden)

Cen Zhaohui

2017-09-01

Full Text Available Gird-connected Photo-Voltaic (PV systems rated as 5-10 kW level have advantages of scalability and energy-saving, so they are very typical for small-scale household solar applications. In this paper, an 8 kW three-phase grid-connected PV system model is proposed and studied. In this high-fidelity model, some basic PV system components such as solar panels, DC-DC converters, DC-AC inverters and three-phase utility grids are mathematically modelled and organized as a complete simulation model. Also, an overall power controller with Maximum Power Point Control (MPPT is proposed to achieve both high-efficiency for solar energy harvesting and grid-connection stability. Finally, simulation results demonstrate the effectiveness of the PV system model and the proposed controller, and power quality issues are discussed.

Simulation Model of a Transient

DEFF Research Database (Denmark)

Jauch, Clemens; Sørensen, Poul; Bak-Jensen, Birgitte

2005-01-01

This paper describes the simulation model of a controller that enables an active-stall wind turbine to ride through transient faults. The simulated wind turbine is connected to a simple model of a power system. Certain fault scenarios are specified and the turbine shall be able to sustain operati...

Simulating soil C stability with mechanistic systems models: a multisite comparison of measured fractions and modelled pools

Science.gov (United States)

Robertson, Andy; Schipanski, Meagan; Sherrod, Lucretia; Ma, Liwang; Ahuja, Lajpat; McNamara, Niall; Smith, Pete; Davies, Christian

2016-04-01

Agriculture, covering more than 30% of global land area, has an exciting opportunity to help combat climate change by effectively managing its soil to promote increased C sequestration. Further, newly sequestered soil carbon (C) through agriculture needs to be stored in more stable forms in order to have a lasting impact on reducing atmospheric CO2 concentrations. While land uses in different climates and soils require different management strategies, the fundamental mechanisms that regulate C sequestration and stabilisation remain the same. These mechanisms are used by a number of different systems models to simulate C dynamics, and thus assess the impacts of change in management or climate. To evaluate the accuracy of these model simulations, our research uses a multidirectional approach to compare C stocks of physicochemical soil fractions collected at two long-term agricultural sites. Carbon stocks for a number of soil fractions were measured at two sites (Lincoln, UK; Colorado, USA) over 8 and 12 years, respectively. Both sites represent managed agricultural land but have notably different climates and levels of disturbance. The measured soil fractions act as proxies for varying degrees of stability, with C contained within these fractions relatable to the C simulated within the soil pools of mechanistic systems models1. Using stable isotope techniques at the UK site, specific turnover times of C within the different fractions were determined and compared with those simulated in the pools of 3 different models of varying complexity (RothC, DayCent and RZWQM2). Further, C dynamics and N-mineralisation rates of the measured fractions at the US site were assessed and compared to results of the same three models. The UK site saw a significant increase in C stocks within the most stable fractions, with topsoil (0-30cm) sequestration rates of just over 0.3 tC ha-1 yr-1 after only 8 years. Further, the sum of all fractions reported C sequestration rates of nearly 1

Modelica-based Modeling and Simulation to Support Research and Development in Building Energy and Control Systems

Energy Technology Data Exchange (ETDEWEB)

Wetter, Michael

2009-02-12

Traditional building simulation programs possess attributes that make them difficult to use for the design and analysis of building energy and control systems and for the support of model-based research and development of systems that may not already be implemented in these programs. This article presents characteristic features of such applications, and it shows how equation-based object-oriented modelling can meet requirements that arise in such applications. Next, the implementation of an open-source component model library for building energy systems is presented. The library has been developed using the equation-based object-oriented Modelica modelling language. Technical challenges of modelling and simulating such systems are discussed. Research needs are presented to make this technology accessible to user groups that have more stringent requirements with respect to the numerical robustness of simulation than a research community may have. Two examples are presented in which models from the here described library were used. The first example describes the design of a controller for a nonlinear model of a heating coil using model reduction and frequency domain analysis. The second example describes the tuning of control parameters for a static pressure reset controller of a variable air volume flow system. The tuning has been done by solving a non-convex optimization problem that minimizes fan energy subject to state constraints.

Modeling and Simulation for Safeguards

International Nuclear Information System (INIS)

Swinhoe, Martyn T.

2012-01-01

The purpose of this talk is to give an overview of the role of modeling and simulation in Safeguards R and D and introduce you to (some of) the tools used. Some definitions are: (1) Modeling - the representation, often mathematical, of a process, concept, or operation of a system, often implemented by a computer program; (2) Simulation - the representation of the behavior or characteristics of one system through the use of another system, especially a computer program designed for the purpose; and (3) Safeguards - the timely detection of diversion of significant quantities of nuclear material. The role of modeling and simulation are: (1) Calculate amounts of material (plant modeling); (2) Calculate signatures of nuclear material etc. (source terms); and (3) Detector performance (radiation transport and detection). Plant modeling software (e.g. FACSIM) gives the flows and amount of material stored at all parts of the process. In safeguards this allow us to calculate the expected uncertainty of the mass and evaluate the expected MUF. We can determine the measurement accuracy required to achieve a certain performance.

Modelling and Simulating multi-echelon food systems

NARCIS (Netherlands)

Vorst, van der J.G.A.J.; Beulens, A.J.M.; Beek, van P.

2000-01-01

This paper presents a method for modelling the dynamic behaviour of food supply chains and evaluating alternative designs of the supply chain by applying discrete-event simulation. The modelling method is based on the concepts of business processes, design variables at strategic and operational

JACOS: AI-based simulation system for man-machine system behavior in NPP

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Kazuo; Yokobayashi, Masao; Tanabe, Fumiya [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kawase, Katsumi [CSK Corp., Tokyo (Japan); Komiya, Akitoshi [Computer Associated Laboratory, Inc., Hitachinaka, Ibaraki (Japan)

2001-08-01

A prototype of a computer simulation system named JACOS (JAERI COgnitive Simulation system) has been developed at JAERI (Japan Atomic Energy Research Institute) to simulate the man-machine system behavior in which both the cognitive behavior of a human operator and the plant behavior affect each other. The objectives of this system development is to provide man-machine system analysts with detailed information on the cognitive process of an operator and the plant behavior affected by operator's actions in accidental situations of a nuclear power plant. The simulation system consists of an operator model and a plant model which are coupled dynamically. The operator model simulates an operator's cognitive behavior in accidental situations based on the decision ladder model of Rasmussen, and is implemented using the AI-techniques of the distributed cooperative inference method with the so-called blackboard architecture. Rule-based behavior is simulated using knowledge representation with If-Then type of rules. Knowledge-based behavior is simulated using knowledge representation with MFM (Multilevel Flow Modeling) and qualitative reasoning method. Cognitive characteristics of attentional narrowing, limitation of short-term memory, and knowledge recalling from long-term memory are also taken into account. The plant model of a 3-loop PWR is also developed using a best estimate thermal-hydraulic analysis code RELAP5/MOD2. This report is prepared as User's Manual for JACOS. The first chapter of this report describes both operator and plant models in detail. The second chapter includes instructive descriptions for program installation, building of a knowledge base for operator model, execution of simulation and analysis of simulation results. The examples of simulation with JACOS are shown in the third chapter. (author)

Healthcare system simulation using Witness

International Nuclear Information System (INIS)

Khakdaman, Masoud; Zeinahvazi, Milad; Zohoori, Bahareh; Nasiri, Fardokht; Wong, Kuan Yew

2013-01-01

Simulation techniques have a proven track record in manufacturing industry as well as other areas such as healthcare system improvement. In this study, simulation model of a health center in Malaysia is developed through the application of WITNESS simulation software which has shown its flexibility and capability in manufacturing industry. Modelling procedure is started through process mapping and data collection and continued with model development, verification, validation and experimentation. At the end, final results and possible future improvements are demonstrated.

Analysis of sensitivity of simulated recharge to selected parameters for seven watersheds modeled using the precipitation-runoff modeling system

Science.gov (United States)

Ely, D. Matthew

2006-01-01

Recharge is a vital component of the ground-water budget and methods for estimating it range from extremely complex to relatively simple. The most commonly used techniques, however, are limited by the scale of application. One method that can be used to estimate ground-water recharge includes process-based models that compute distributed water budgets on a watershed scale. These models should be evaluated to determine which model parameters are the dominant controls in determining ground-water recharge. Seven existing watershed models from different humid regions of the United States were chosen to analyze the sensitivity of simulated recharge to model parameters. Parameter sensitivities were determined using a nonlinear regression computer program to generate a suite of diagnostic statistics. The statistics identify model parameters that have the greatest effect on simulated ground-water recharge and that compare and contrast the hydrologic system responses to those parameters. Simulated recharge in the Lost River and Big Creek watersheds in Washington State was sensitive to small changes in air temperature. The Hamden watershed model in west-central Minnesota was developed to investigate the relations that wetlands and other landscape features have with runoff processes. Excess soil moisture in the Hamden watershed simulation was preferentially routed to wetlands, instead of to the ground-water system, resulting in little sensitivity of any parameters to recharge. Simulated recharge in the North Fork Pheasant Branch watershed, Wisconsin, demonstrated the greatest sensitivity to parameters related to evapotranspiration. Three watersheds were simulated as part of the Model Parameter Estimation Experiment (MOPEX). Parameter sensitivities for the MOPEX watersheds, Amite River, Louisiana and Mississippi, English River, Iowa, and South Branch Potomac River, West Virginia, were similar and most sensitive to small changes in air temperature and a user-defined flow

Modeling and simulation in the design and evaluation of conceptual safeguards systems

International Nuclear Information System (INIS)

Cobb, D.D.; Smith, D.B.

1977-01-01

Recent work in modeling nuclear fuel-cycle processes and the materials measurement and accountability portion of integrated safeguards systems is summarized. Process variability, especially in the levels of in-process holdup and in scrap and waste sidestreams, impacts significantly on the design of dynamic materials accounting and control systems. In the absence of operating data from modern facilities, detailed dynamic models of process operation are required in order to evaluate systems design concepts. Numerical data are presented from the simulated operation of major portions of spent fuel reprocessing, plutonium nitrate-to-oxide conversion, and mixed-oxide fuel-fabrication processes

Modeling and Compensation Design for a Power Hardware-in-the-Loop Simulation of an AC Distribution System: Preprint

Energy Technology Data Exchange (ETDEWEB)

Prabakar, Kumaraguru [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ainsworth, Nathan [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pratt, Annabelle [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Baggu, Murali M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hariri, Ali [Formerly NREL

2017-10-06

Power hardware-in-the-loop (PHIL) simulation, where actual hardware under text is coupled with a real-time digital model in closed loop, is a powerful tool for analyzing new methods of control for emerging distributed power systems. However, without careful design and compensation of the interface between the simulated and actual systems, PHIL simulations may exhibit instability and modeling inaccuracies. This paper addresses issues that arise in the PHIL simulation of a hardware battery inverter interfaced with a simulated distribution feeder. Both the stability and accuracy issues are modeled and characterized, and a methodology for design of PHIL interface compensation to ensure stability and accuracy is presented. The stability and accuracy of the resulting compensated PHIL simulation is then shown by experiment.

Modelling and Simulation of Grid Connected SPV System with Active Power Filtering Features

Science.gov (United States)

Saroha, Jaipal; Pandove, Gitanjali; Singh, Mukhtiar

2017-09-01

In this paper, the detailed simulation studies for a grid connected solar photovoltaic system (SPV) have been presented. The power electronics devices like DC-DC boost converter and grid interfacing inverter are most important components of proposed system. Here, the DC-DC boost converter is controlled to extract maximum power out of SPV under different irradiation levels, while the grid interfacing inverter is utilized to evacuate the active power and feed it into grid at synchronized voltage and frequency. Moreover, the grid interfacing inverter is also controlled to sort out the issues related to power quality by compensating the reactive power and harmonics current component of nearby load at point of common coupling. Besides, detailed modeling of various component utilized in proposed system is also presented. Finally, extensive simulations have been performed under different irradiation levels with various kinds of load to validate the aforementioned claims. The overall system design and simulation have been performed by using Sim Power System toolbox available in the library of MATLAB.

Simulation of Tillage Systems Impact on Soil Biophysical Properties Using the SALUS Model

Directory of Open Access Journals (Sweden)

Luigi Sartori

2011-02-01

Full Text Available A sustainable land management has been defined as the management system that allows for production, while minimizing risk, maintaining quality of soil and water. Tillage systems can significantly decrease soil carbon storage and influence the soil environment of a crop. Crop growth models can be useful tools in evaluating the impact of different tillage systems on soil biophysical properties and on the growth and final yield of the crops. The objectives of this paper were i to illustrate the SALUS model and its tillage component; ii to evaluate the effects of different tillage systems on water infiltration and time to ponding, iii to simulate the effect of tillage systems on some soil biophysical properties. The SALUS (System Approach to Land Use Sustainability model is designed to simulate continuous crop, soil, water and nutrient conditions under different tillage and crop residues management strategies for multiple years. Predictions of changes in surface residue, bulk density, runoff, drainage and evaporation were consistent with expected behaviours of these parameters as described in the literature. The experiment to estimate the time to ponding curve under different tillage system confirmed the theory and showed the beneficial effects of the residue on soil surface with respect to water infiltration. It also showed that the no-tillage system is a more appropriate system to adopt in areas characterized by high intensity rainfall.

Simulation of Tillage Systems Impact on Soil Biophysical Properties Using the SALUS Model

Directory of Open Access Journals (Sweden)

Bruno Basso

2006-12-01

Full Text Available A sustainable land management has been defined as the management system that allows for production, while minimizing risk, maintaining quality of soil and water. Tillage systems can significantly decrease soil carbon storage and influence the soil environment of a crop. Crop growth models can be useful tools in evaluating the impact of different tillage systems on soil biophysical properties and on the growth and final yield of the crops. The objectives of this paper were i to illustrate the SALUS model and its tillage component; ii to evaluate the effects of different tillage systems on water infiltration and time to ponding, iii to simulate the effect of tillage systems on some soil biophysical properties. The SALUS (System Approach to Land Use Sustainability model is designed to simulate continuous crop, soil, water and nutrient conditions under different tillage and crop residues management strategies for multiple years. Predictions of changes in surface residue, bulk density, runoff, drainage and evaporation were consistent with expected behaviours of these parameters as described in the literature. The experiment to estimate the time to ponding curve under different tillage system confirmed the theory and showed the beneficial effects of the residue on soil surface with respect to water infiltration. It also showed that the no-tillage system is a more appropriate system to adopt in areas characterized by high intensity rainfall.

A high fidelity model and code generator for the simulation of BOP systems

International Nuclear Information System (INIS)

Galen, S.; Vinay, M.

1993-01-01

TOPMERET represents a significant advance in the modelling fidelity of Balance of Plant systems (BOP). It is extremely flexible and can accommodate a variety of systems, including main steam, feedwater, turbine, condenser, offgas, large volumes, such as the containment, and water systems such as service water. It handles both normal and abnormal operating scenarios, including pipe break accidents. It was tested successfully on various simulators, and meets the fidelity required of BOP system models so as to successfully integrate with the high level of control automation of European designs. (Z.S.) 1 ref

Modelling and simulation of a heat exchanger

Science.gov (United States)

Xia, Lei; Deabreu-Garcia, J. Alex; Hartley, Tom T.

1991-01-01

Two models for two different control systems are developed for a parallel heat exchanger. First by spatially lumping a heat exchanger model, a good approximate model which has a high system order is produced. Model reduction techniques are applied to these to obtain low order models that are suitable for dynamic analysis and control design. The simulation method is discussed to ensure a valid simulation result.

Modeling energy market dynamics using discrete event system simulation

International Nuclear Information System (INIS)

Gutierrez-Alcaraz, G.; Sheble, G.B.

2009-01-01

This paper proposes the use of Discrete Event System Simulation to study the interactions among fuel and electricity markets and consumers, and the decision-making processes of fuel companies (FUELCOs), generation companies (GENCOs), and consumers in a simple artificial energy market. In reality, since markets can reach a stable equilibrium or fail, it is important to observe how they behave in a dynamic framework. We consider a Nash-Cournot model in which marketers are depicted as Nash-Cournot players that determine supply to meet end-use consumption. Detailed engineering considerations such as transportation network flows are omitted, because the focus is upon the selection and use of appropriate market models to provide answers to policy questions. (author)

Global ice sheet/RSL simulations using the higher-order Ice Sheet System Model.

Science.gov (United States)

Larour, E. Y.; Ivins, E. R.; Adhikari, S.; Schlegel, N.; Seroussi, H. L.; Morlighem, M.

2017-12-01

Relative sea-level rise is driven by processes that are intimately linked to the evolution ofglacial areas and ice sheets in particular. So far, most Earth System models capable of projecting theevolution of RSL on decadal to centennial time scales have relied on offline interactions between RSL andice sheets. In particular, grounding line and calving front dynamics have not been modeled in a way that istightly coupled with Elasto-Static Adjustment (ESA) and/or Glacial-Isostatic Adjustment (GIA). Here, we presenta new simulation of the entire Earth System in which both Greenland and Antarctica ice sheets are tightly coupledto an RSL model that includes both ESA and GIA at resolutions and time scales compatible with processes suchas grounding line dynamics for Antarctica ice shelves and calving front dynamics for Greenland marine-terminatingglaciers. The simulations rely on the Ice Sheet System Model (ISSM) and show the impact of higher-orderice flow dynamics and coupling feedbacks between ice flow and RSL. We quantify the exact impact of ESA andGIA inclusion on grounding line evolution for large ice shelves such as the Ronne and Ross ice shelves, as well asthe Agasea Embayment ice streams, and demonstate how offline vs online RSL simulations diverge in the long run,and the consequences for predictions of sea-level rise.This work was performed at the California Institute of Technology's Jet Propulsion Laboratory undera contract with the National Aeronautics and Space Administration's Cryosphere Science Program.

Catchment & sewer network simulation model to benchmark control strategies within urban wastewater systems

DEFF Research Database (Denmark)

Saagi, Ramesh; Flores Alsina, Xavier; Fu, Guangtao

2016-01-01

This paper aims at developing a benchmark simulation model to evaluate control strategies for the urban catchment and sewer network. Various modules describing wastewater generation in the catchment, its subsequent transport and storage in the sewer system are presented. Global/local overflow based...... evaluation criteria describing the cumulative and acute effects are presented. Simulation results show that the proposed set of models is capable of generating daily, weekly and seasonal variations as well as describing the effect of rain events on wastewater characteristics. Two sets of case studies...

Train-to-Ground communications of a Train Control and Monitoring Systems: A simulation platform modelling approach

DEFF Research Database (Denmark)

Bouaziz, Maha; Yan, Ying; Kassab, Mohamed

2018-01-01

wireless technologies, e.g. Wi-Fi and LTE. Different T2G scenarios are defined in order to evaluate the performances of the Mobile Communication Gateway (managing train communications) and Quality of Services (QoS) offered to TCMS applications in the context of various environments (regular train lines......Under the SAFE4RAIL project, we are developing a simulation platform based on a discrete-events network simulator. This platform models the Train-to-Ground (T2G) link in the framework of a system-level simulation of Train Control Management System (TCMS). The modelled T2G link is based on existing...

A Cryogenic Fluid System Simulation in Support of Integrated Systems Health Management

Science.gov (United States)

Barber, John P.; Johnston, Kyle B.; Daigle, Matthew

2013-01-01

Simulations serve as important tools throughout the design and operation of engineering systems. In the context of sys-tems health management, simulations serve many uses. For one, the underlying physical models can be used by model-based health management tools to develop diagnostic and prognostic models. These simulations should incorporate both nominal and faulty behavior with the ability to inject various faults into the system. Such simulations can there-fore be used for operator training, for both nominal and faulty situations, as well as for developing and prototyping health management algorithms. In this paper, we describe a methodology for building such simulations. We discuss the design decisions and tools used to build a simulation of a cryogenic fluid test bed, and how it serves as a core technology for systems health management development and maturation.

Work Practice Simulation of Complex Human-Automation Systems in Safety Critical Situations: The Brahms Generalized berlingen Model

Science.gov (United States)

Clancey, William J.; Linde, Charlotte; Seah, Chin; Shafto, Michael

2013-01-01

The transition from the current air traffic system to the next generation air traffic system will require the introduction of new automated systems, including transferring some functions from air traffic controllers to on­-board automation. This report describes a new design verification and validation (V&V) methodology for assessing aviation safety. The approach involves a detailed computer simulation of work practices that includes people interacting with flight-critical systems. The research is part of an effort to develop new modeling and verification methodologies that can assess the safety of flight-critical systems, system configurations, and operational concepts. The 2002 Ueberlingen mid-air collision was chosen for analysis and modeling because one of the main causes of the accident was one crew's response to a conflict between the instructions of the air traffic controller and the instructions of TCAS, an automated Traffic Alert and Collision Avoidance System on-board warning system. It thus furnishes an example of the problem of authority versus autonomy. It provides a starting point for exploring authority/autonomy conflict in the larger system of organization, tools, and practices in which the participants' moment-by-moment actions take place. We have developed a general air traffic system model (not a specific simulation of Überlingen events), called the Brahms Generalized Ueberlingen Model (Brahms-GUeM). Brahms is a multi-agent simulation system that models people, tools, facilities/vehicles, and geography to simulate the current air transportation system as a collection of distributed, interactive subsystems (e.g., airports, air-traffic control towers and personnel, aircraft, automated flight systems and air-traffic tools, instruments, crew). Brahms-GUeM can be configured in different ways, called scenarios, such that anomalous events that contributed to the Überlingen accident can be modeled as functioning according to requirements or in an

Modelling of core protection and monitoring system for PWR nuclear power plant simulator

International Nuclear Information System (INIS)

Jung Kun Lee; Byoung Sung Han

1997-01-01

A nuclear power plant simulator was developed for Younggwang units 3 and 4 nuclear power plant (YGN Nos 3 and 4) in Korea; it has been in operation on training center since November 1996. The core protection calculator (CPC) and the core operating limit supervisory system (COLSS) for the simulator were also developed. The CPC is a digital computer-based core protection system, which performs on-line calculation of departure from nucleate boiling ratio (DNBR) and local power density (LPD). It initiates reactor trip when the core conditions exceed designated DNBR or LPD limitations. The COLSS is designed to assist operators by implementing the limiting conditions for operations in the technical specifications. With these systems, it is possible to increase capacity factor and safety of nuclear power plants, because the COLSS data can show accurate operation margin to plant operators and the CPC can protect reactor core. In this study, the function of CPC/COLSS is analyzed in detail, and then simulation model for CPC/COLSS is presented based on the function. Compared with the YGN Nos 3 and 4 plant operation data and CEDIPS/COLSS FORTRAN code test results, the predictions with the model show reasonable results. (Author)

Development of Three-Layer Simulation Model for Freezing Process of Food Solution Systems

Science.gov (United States)

Kaminishi, Koji; Araki, Tetsuya; Shirakashi, Ryo; Ueno, Shigeaki; Sagara, Yasuyuki

A numerical model has been developed for simulating freezing phenomena of food solution systems. The cell model was simplified to apply to food solution systems, incorporating with the existence of 3 parts such as unfrozen, frozen and moving boundary layers. Moreover, the moving rate of freezing front model was also introduced and calculated by using the variable space network method proposed by Murray and Landis (1957). To demonstrate the validity of the model, it was applied to the freezing processes of coffee solutions. Since the model required the phase diagram of the material to be frozen, the initial freezing temperatures of 1-55 % coffee solutions were measured by the DSC method. The effective thermal conductivity for coffee solutions was determined as a function of temperature and solute concentration by using the Maxwell - Eucken model. One-dimensional freezing process of 10 % coffee solution was simulated based on its phase diagram and thermo-physical properties. The results were good agreement with the experimental data and then showed that the model could accurately describe the change in the location of the freezing front and the distributions of temperature as well as ice fraction during a freezing process.

Simulation for a Coevolved System-of-Systems Meta-Architecture

Energy Technology Data Exchange (ETDEWEB)

Muller, George; Dagli, Cihan

2016-08-15

This paper describes a simulation of a system-of-systems for counter-smuggling. The simulation is described and results are provided. The results demonstrate the applicability of the agent based modeling paradigm to understand key factors influencing SoS performance.

Coupling fast fluid dynamics and multizone airflow models in Modelica Buildings library to simulate the dynamics of HVAC systems

Energy Technology Data Exchange (ETDEWEB)

Tian, Wei [Univ. of Miami, FL (United States). Dept. of Civil, Architectural and Environmental Engineering; Sevilla, Thomas Alonso [Univ. of Miami, FL (United States). Dept. of Civil, Architectural and Environmental Engineering; Zuo, Wangda [Univ. of Miami, FL (United States). Dept. of Civil, Architectural and Environmental Engineering; Sohn, Michael D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Analysis and Environmental Impacts Div.

2017-06-08

Historically, multizone models are widely used in building airflow and energy performance simulations due to their fast computing speed. However, multizone models assume that the air in a room is well mixed, consequently limiting their application. In specific rooms where this assumption fails, the use of computational fluid dynamics (CFD) models may be an alternative option. Previous research has mainly focused on coupling CFD models and multizone models to study airflow in large spaces. While significant, most of these analyses did not consider the coupled simulation of the building airflow with the building's Heating, Ventilation, and Air-Conditioning (HVAC) systems. This paper tries to fill the gap by integrating the models for HVAC systems with coupled multizone and CFD simulations for airflows, using the Modelica simul ation platform. To improve the computational efficiency, we incorporated a simplified CFD model named fast fluid dynamics (FFD). We first introduce the data synchronization strategy and implementation in Modelica. Then, we verify the implementation using two case studies involving an isothermal and a non-isothermal flow by comparing model simulations to experiment data. Afterward, we study another three cases that are deemed more realistic. This is done by attaching a variable air volume (VAV) terminal box and a VAV system to previous flows to assess the capability of the models in studying the dynamic control of HVAC systems. Finally, we discuss further research needs on the coupled simulation using the models.

Intraocular Telescopic System Design: Optical and Visual Simulation in a Human Eye Model

Directory of Open Access Journals (Sweden)

Georgios Zoulinakis

2017-01-01

Full Text Available Purpose. To design an intraocular telescopic system (ITS for magnifying retinal image and to simulate its optical and visual performance after implantation in a human eye model. Methods. Design and simulation were carried out with a ray-tracing and optical design software. Two different ITS were designed, and their visual performance was simulated using the Liou-Brennan eye model. The difference between the ITS was their lenses’ placement in the eye model and their powers. Ray tracing in both centered and decentered situations was carried out for both ITS while visual Strehl ratio (VSOTF was computed using custom-made MATLAB code. Results. The results show that between 0.4 and 0.8 mm of decentration, the VSOTF does not change much either for far or near target distances. The image projection for these decentrations is in the parafoveal zone, and the quality of the image projected is quite similar. Conclusion. Both systems display similar quality while they differ in size; therefore, the choice between them would need to take into account specific parameters from the patient’s eye. Quality does not change too much between 0.4 and 0.8 mm of decentration for either system which gives flexibility to the clinician to adjust decentration to avoid areas of retinal damage.

Definition, modeling and simulation of a grid computing system for high throughput computing

CERN Document Server

Caron, E; Tsaregorodtsev, A Yu

2006-01-01

In this paper, we study and compare grid and global computing systems and outline the benefits of having an hybrid system called dirac. To evaluate the dirac scheduling for high throughput computing, a new model is presented and a simulator was developed for many clusters of heterogeneous nodes belonging to a local network. These clusters are assumed to be connected to each other through a global network and each cluster is managed via a local scheduler which is shared by many users. We validate our simulator by comparing the experimental and analytical results of a M/M/4 queuing system. Next, we do the comparison with a real batch system and we obtain an average error of 10.5% for the response time and 12% for the makespan. We conclude that the simulator is realistic and well describes the behaviour of a large-scale system. Thus we can study the scheduling of our system called dirac in a high throughput context. We justify our decentralized, adaptive and oppor! tunistic approach in comparison to a centralize...

Graphical models for simulation and control of robotic systems for waste handling

International Nuclear Information System (INIS)

Drotning, W.D.; Bennett, P.C.

1992-01-01

This paper discusses detailed geometric models which have been used within a graphical simulation environment to study transportation cask facility design and to perform design and analyses of robotic systems for handling of nuclear waste. The models form the basis for a robot control environment which provides safety, flexibility, and reliability for operations which span the spectrum from autonomous control to tasks requiring direct human intervention

Advances in Intelligent Modelling and Simulation Simulation Tools and Applications

CERN Document Server

Oplatková, Zuzana; Carvalho, Marco; Kisiel-Dorohinicki, Marek

2012-01-01

The human capacity to abstract complex systems and phenomena into simplified models has played a critical role in the rapid evolution of our modern industrial processes and scientific research. As a science and an art, Modelling and Simulation have been one of the core enablers of this remarkable human trace, and have become a topic of great importance for researchers and practitioners. This book was created to compile some of the most recent concepts, advances, challenges and ideas associated with Intelligent Modelling and Simulation frameworks, tools and applications. The first chapter discusses the important aspects of a human interaction and the correct interpretation of results during simulations. The second chapter gets to the heart of the analysis of entrepreneurship by means of agent-based modelling and simulations. The following three chapters bring together the central theme of simulation frameworks, first describing an agent-based simulation framework, then a simulator for electrical machines, and...

Dynamic model for the control system simulation and design of a 200 MW nuclear heating reactor

International Nuclear Information System (INIS)

Zhang Yuai; Liu Longzhi; Ma Changwen

1999-01-01

The author develops a nonlinear dynamic model used in a wide range control system simulation for a 200 MW Nuclear Heating Reactor (NHR-200). Besides a one-point neutron kinetics equation and temperature feedback based on the lumped fuel and coolant temperature, which are the usual methods used in modeling of PWR, two other factors are also considered in order to suit the wide range operation. The first consideration is the natural circulation in the primary loop because it affects the heat transfer coefficients in the core and in the primary heat exchanger (PHE). The second consideration is the flow rate variation in the secondary loop which leads to some nonlinear properties. The simulation results show that the model is accurate enough for control system simulation. Some model reduction basis can be obtained through the dynamic analysis

Comparison of Two Models for Damage Accumulation in Simulations of System Performance

Energy Technology Data Exchange (ETDEWEB)

Youngblood, R. [Idaho National Laboratory, Idaho Falls, ID (United States); Mandelli, D. [Idaho National Laboratory, Idaho Falls, ID (United States)

2015-11-01

A comprehensive simulation study of system performance needs to address variations in component behavior, variations in phenomenology, and the coupling between phenomenology and component failure. This paper discusses two models of this: 1. damage accumulation is modeled as a random walk process in each time history, with component failure occurring when damage accumulation reaches a specified threshold; or 2. damage accumulation is modeled mechanistically within each time history, but failure occurs when damage reaches a time-history-specific threshold, sampled at time zero from each component’s distribution of damage tolerance. A limiting case of the latter is classical discrete-event simulation, with component failure times sampled a priori from failure time distributions; but in such models, the failure times are not typically adjusted for operating conditions varying within a time history. Nowadays, as discussed below, it is practical to account for this. The paper compares the interpretations and computational aspects of the two models mentioned above.

Magnetosphere Modeling: From Cartoons to Simulations

Science.gov (United States)

Gombosi, T. I.

2017-12-01

Over the last half a century physics-based global computer simulations became a bridge between experiment and basic theory and now it represents the "third pillar" of geospace research. Today, many of our scientific publications utilize large-scale simulations to interpret observations, test new ideas, plan campaigns, or design new instruments. Realistic simulations of the complex Sun-Earth system have been made possible by the dramatically increased power of both computing hardware and numerical algorithms. Early magnetosphere models were based on simple E&M concepts (like the Chapman-Ferraro cavity) and hydrodynamic analogies (bow shock). At the beginning of the space age current system models were developed culminating in the sophisticated Tsyganenko-type description of the magnetic configuration. The first 3D MHD simulations of the magnetosphere were published in the early 1980s. A decade later there were several competing global models that were able to reproduce many fundamental properties of the magnetosphere. The leading models included the impact of the ionosphere by using a height-integrated electric potential description. Dynamic coupling of global and regional models started in the early 2000s by integrating a ring current and a global magnetosphere model. It has been recognized for quite some time that plasma kinetic effects play an important role. Presently, global hybrid simulations of the dynamic magnetosphere are expected to be possible on exascale supercomputers, while fully kinetic simulations with realistic mass ratios are still decades away. In the 2010s several groups started to experiment with PIC simulations embedded in large-scale 3D MHD models. Presently this integrated MHD-PIC approach is at the forefront of magnetosphere simulations and this technique is expected to lead to some important advances in our understanding of magnetosheric physics. This talk will review the evolution of magnetosphere modeling from cartoons to current systems

System studies for micro grid design: modeling and simulation examples

Energy Technology Data Exchange (ETDEWEB)

Rosa, Arlei Lucas S. [Federal University of Juiz de Fora (UFJF), MG (Brazil); Ribeiro, Paulo F. [Calvin College, Grand Rapids, MI (United States). Electrical Engineering Dept.

2009-07-01

The search for new energy sources to replace or increase the existing power plant of the traditional system leads to changes in concepts of energy generation and consumption. In this context, the concept of Microgrid has been developed and opens the opportunity for local power generation. The Microgrid can operate connected to the existing distribution network, increasing the reliability and safety of the system. Control measures and electronics interface are taken to maintain the network as a single and strong unit to any perturbation. This paper presents the typical system studies required to investigate the performance of a Microgrid operating under different system condition (e.g. interconnected or isolated from the utility grid and under system disturbance). Load flow and electromagnetic transient studies are used for modeling and simulation of a typical Microgrid configuration. (author)

Hanford solid waste management system simulation

International Nuclear Information System (INIS)

Shaver, S.R.; Armacost, L.L.; Konynenbelt, H.S.; Wehrman, R.R.

1994-12-01

This paper describes systems analysis and simulation model development for a proposed solid waste management system at a U.S. Department of Energy Site. The proposed system will include a central storage facility, four treatment facilities, and three disposal sites. The material managed by this system will include radioactive, hazardous, and mixed radioactive and hazardous wastes. The objective of the modeling effort is to provide a means of evaluating throughput and capacity requirements for the proposed treatment, storage, and disposal facilities. The model is used to evaluate alternative system configurations and the effect on the alternatives of changing waste stream characteristics and receipt schedules. An iterative modeling and analysis approach is used that provides macro-level models early in the project and establishes credibility with the customer. The results from the analyses based on the macro models influence system design decisions and provide information that helps focus subsequent model development. Modeling and simulation of alternative system configurations and operating strategies yield a better understanding of the solid waste system requirements. The model effectively integrates information obtained through systems analysis and waste characterization to provide a consistent basis for system and facility planning

Theory of nuclear spin relaxation in disordered systems: comparison of Bloembergen-Purcell-Pound models and Monte Carlo simulations

International Nuclear Information System (INIS)

Luo Xinjun; Sholl, C.A.

2002-01-01

Two Bloembergen-Purcell-Pound (BPP) models for analysing nuclear spin relaxation data for translational diffusion in disordered systems are compared with Monte Carlo simulations. One model (the a-BPP model, 'a' standing for average) is commonly used for disordered systems and the other (the Cameron-Sholl BPP model) is more rigorously based and can distinguish between site-and barrier-energy disorder. Simulated relaxation data produced using Gaussian distributions of energy disorder are analysed using the models, and the parameters obtained from the fits are compared with the values used for the simulations. It is found that both models can give reasonable fits to the data. Both models also give reasonable agreement with the simulation parameters provided that the standard deviation of the energy distribution for the a-BPP model is interpreted as the average of the site-and barrier-energy standard deviations. Quantitative estimates are given of the accuracy of the parameters from the fits. (author)

Hardware-in-the-Loop Simulation of a Distribution System with Air Conditioners under Model Predictive Control: Preprint

Energy Technology Data Exchange (ETDEWEB)

Sparn, Bethany F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ruth, Mark F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Krishnamurthy, Dheepak [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pratt, Annabelle [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lunacek, Monte S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jones, Wesley B [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wu, Hongyu [Kansas State University; Mittal, Saurabh [Mitre Corporation; Marks, Jesse [University of Missouri

2017-08-01

Many have proposed that responsive load provided by distributed energy resources (DERs) and demand response (DR) are an option to provide flexibility to the grid and especially to distribution feeders. However, because responsive load involves a complex interplay between tariffs and DER and DR technologies, it is challenging to test and evaluate options without negatively impacting customers. This paper describes a hardware-in-the-loop (HIL) simulation system that has been developed to reduce the cost of evaluating the impact of advanced controllers (e.g., model predictive controllers) and technologies (e.g., responsive appliances). The HIL simulation system combines large-scale software simulation with a small set of representative building equipment hardware. It is used to perform HIL simulation of a distribution feeder and the loads on it under various tariff structures. In the reported HIL simulation, loads include many simulated air conditioners and one physical air conditioner. Independent model predictive controllers manage operations of all air conditioners under a time-of-use tariff. Results from this HIL simulation and a discussion of future development work of the system are presented.

Simulation Models to Size and Retrofit District Heating Systems

Directory of Open Access Journals (Sweden)

Kevin Sartor

2017-12-01

Full Text Available District heating networks are considered as convenient systems to supply heat to consumers while reducing CO 2 emissions and increasing renewable energies use. However, to make them as profitable as possible, they have to be developed, operated and sized carefully. In order to cope with these objectives, simulation tools are required to analyze several configuration schemes and control methods. Indeed, the most common problems are heat losses, the electric pump consumption and the peak heat demand while ensuring the comfort of the users. In this contribution, a dynamic simulation model of all the components of the network is described. It is dedicated to assess some energetic, environmental and economic indicators. Finally, the methodology is used on an existing application test case namely the district heating network of the University of Liège to study the pump control and minimize the district heating network heat losses.

Developing a versatile simulation, scheduling and economic model framework for bioenergy production systems

Directory of Open Access Journals (Sweden)

Robert Matindi

2019-01-01

Full Text Available Modelling is an effective way of designing, understanding, and analysing bio-refinery supply chain systems. The supply chain is a complex process consisting of many systems interacting with each other. It requires the modelling of the processes in the presence of multiple autonomous entities (i.e. biomass producers, bio-processors and transporters, multiple performance measures and multiple objectives, both local and global, which together constitute very complex interaction effects. In this paper, simulation models for recovering biomass from the field of the biorefinery are developed and validated using some industry data and the minimum biomass recovery cost is established based on different strategies employed for recovering biomass. Energy densification techniques are evaluated for their net present worth and the technologies that offer greater returns for the industry are recommended. In addition, a new scheduling algorithm is also developed to enhance the process flow of the management of resources and the flow of biomass. The primary objective is to investigate different strategies to reach the lowest cost delivery of sugarcane harvest residue to a sugar factory through optimally located bio-refineries. A simulation /optimisation solution approach is also developed to tackle the stochastic variables in the bioenergy production system based on different statistical distributions such as Weibull and Pearson distributions. In this approach, a genetic algorithm is integrated with simulation to improve the initial solution and search the near-optimal solution. A case study is conducted to illustrate the results and to validate the applicability for the real world implementation using ExtendSIM Simulation software using some real data from Australian Mills.

Smart systems integration and simulation

CERN Document Server

Poncino, Massimo; Pravadelli, Graziano

2016-01-01

This book-presents new methods and tools for the integration and simulation of smart devices. The design approach described in this book explicitly accounts for integration of Smart Systems components and subsystems as a specific constraint. It includes methodologies and EDA tools to enable multi-disciplinary and multi-scale modeling and design, simulation of multi-domain systems, subsystems and components at all levels of abstraction, system integration and exploration for optimization of functional and non-functional metrics. By covering theoretical and practical aspects of smart device design, this book targets people who are working and studying on hardware/software modelling, component integration and simulation under different positions (system integrators, designers, developers, researchers, teachers, students etc.). In particular, it is a good introduction to people who have interest in managing heterogeneous components in an efficient and effective way on different domains and different abstraction l...

Computer Simulation and Modeling of CO2 Removal Systems for Exploration 2013-2014

Science.gov (United States)

Coker, R.; Knox, J.; Gomez, C.

2015-01-01

The Atmosphere Revitalization Recovery and Environmental Monitoring (ARREM) project was initiated in September of 2011 as part of the Advanced Exploration Systems (AES) program. Under the ARREM project and the follow-on Life Support Systems (LSS) project, testing of sub-scale and full-scale systems has been combined with multiphysics computer simulations for evaluation and optimization of subsystem approaches. In particular, this paper will describes the testing and 1-D modeling of the combined water desiccant and carbon dioxide sorbent subsystems of the carbon dioxide removal assembly (CDRA). The goal is a full system predictive model of CDRA to guide system optimization and development.

Integrated water system simulation by considering hydrological and biogeochemical processes: model development, with parameter sensitivity and autocalibration

Science.gov (United States)

Zhang, Y. Y.; Shao, Q. X.; Ye, A. Z.; Xing, H. T.; Xia, J.

2016-02-01

Integrated water system modeling is a feasible approach to understanding severe water crises in the world and promoting the implementation of integrated river basin management. In this study, a classic hydrological model (the time variant gain model: TVGM) was extended to an integrated water system model by coupling multiple water-related processes in hydrology, biogeochemistry, water quality, and ecology, and considering the interference of human activities. A parameter analysis tool, which included sensitivity analysis, autocalibration and model performance evaluation, was developed to improve modeling efficiency. To demonstrate the model performances, the Shaying River catchment, which is the largest highly regulated and heavily polluted tributary of the Huai River basin in China, was selected as the case study area. The model performances were evaluated on the key water-related components including runoff, water quality, diffuse pollution load (or nonpoint sources) and crop yield. Results showed that our proposed model simulated most components reasonably well. The simulated daily runoff at most regulated and less-regulated stations matched well with the observations. The average correlation coefficient and Nash-Sutcliffe efficiency were 0.85 and 0.70, respectively. Both the simulated low and high flows at most stations were improved when the dam regulation was considered. The daily ammonium-nitrogen (NH4-N) concentration was also well captured with the average correlation coefficient of 0.67. Furthermore, the diffuse source load of NH4-N and the corn yield were reasonably simulated at the administrative region scale. This integrated water system model is expected to improve the simulation performances with extension to more model functionalities, and to provide a scientific basis for the implementation in integrated river basin managements.

Simulation modelling of central order processing system under resource sharing strategy in demand-driven garment supply chains

Science.gov (United States)

Ma, K.; Thomassey, S.; Zeng, X.

2017-10-01

In this paper we proposed a central order processing system under resource sharing strategy for demand-driven garment supply chains to increase supply chain performances. We examined this system by using simulation technology. Simulation results showed that significant improvement in various performance indicators was obtained in new collaborative model with proposed system.

A verilog simulation of the CDF DAQ system

Energy Technology Data Exchange (ETDEWEB)

Schurecht, K.; Harris, R. (Fermi National Accelerator Lab., Batavia, IL (United States)); Sinervo, P.; Grindley, R. (Toronto Univ., ON (Canada). Dept. of Physics)

1991-11-01

A behavioral simulation of the CDF data acquisition system was written in the Verilog modeling language in order to investigate the effects of various improvements to the existing system. This system is modeled as five separate components that communicate with each other via Fastbus interrupt messages. One component of the system, the CDF event builder, is modeled in substantially greater detail due to its complex structure. This simulation has been verified by comparing its performance with that of the existing DAQ system. Possible improvements to the existing systems were studied using the simulation, and the optimal upgrade path for the system was chosen on the basis of these studies. The overall throughput of the modified system is estimated to be double that of the existing setup. Details of this modeling effort will be discussed, including a comparison of the modeled and actual performance of the existing system.

A verilog simulation of the CDF DAQ system

International Nuclear Information System (INIS)

Schurecht, K.; Harris, R.; Sinervo, P.; Grindley, R.

1991-11-01

A behavioral simulation of the CDF data acquisition system was written in the Verilog modeling language in order to investigate the effects of various improvements to the existing system. This system is modeled as five separate components that communicate with each other via Fastbus interrupt messages. One component of the system, the CDF event builder, is modeled in substantially greater detail due to its complex structure. This simulation has been verified by comparing its performance with that of the existing DAQ system. Possible improvements to the existing systems were studied using the simulation, and the optimal upgrade path for the system was chosen on the basis of these studies. The overall throughput of the modified system is estimated to be double that of the existing setup. Details of this modeling effort will be discussed, including a comparison of the modeled and actual performance of the existing system

MASADA: A MODELING AND SIMULATION AUTOMATED DATA ANALYSIS FRAMEWORK FOR CONTINUOUS DATA-INTENSIVE VALIDATION OF SIMULATION MODELS

CERN Document Server

Foguelman, Daniel Jacob; The ATLAS collaboration

2016-01-01

Complex networked computer systems are usually subjected to upgrades and enhancements on a continuous basis. Modeling and simulation of such systems helps with guiding their engineering processes, in particular when testing candi- date design alternatives directly on the real system is not an option. Models are built and simulation exercises are run guided by specific research and/or design questions. A vast amount of operational conditions for the real system need to be assumed in order to focus on the relevant questions at hand. A typical boundary condition for computer systems is the exogenously imposed workload. Meanwhile, in typical projects huge amounts of monitoring information are logged and stored with the purpose of studying the system’s performance in search for improvements. Also research questions change as systems’ operational conditions vary throughout its lifetime. This context poses many challenges to determine the validity of simulation models. As the behavioral empirical base of the sys...

MASADA: A Modeling and Simulation Automated Data Analysis framework for continuous data-intensive validation of simulation models

CERN Document Server

Foguelman, Daniel Jacob; The ATLAS collaboration

2016-01-01

Complex networked computer systems are usually subjected to upgrades and enhancements on a continuous basis. Modeling and simulation of such systems helps with guiding their engineering processes, in particular when testing candi- date design alternatives directly on the real system is not an option. Models are built and simulation exercises are run guided by specific research and/or design questions. A vast amount of operational conditions for the real system need to be assumed in order to focus on the relevant questions at hand. A typical boundary condition for computer systems is the exogenously imposed workload. Meanwhile, in typical projects huge amounts of monitoring information are logged and stored with the purpose of studying the system’s performance in search for improvements. Also research questions change as systems’ operational conditions vary throughout its lifetime. This context poses many challenges to determine the validity of simulation models. As the behavioral empirical base of the sys...

Modelling, Simulation, Animation, and Real-Time Control (Mosart) for a Class of Electromechanical Systems: A System-Theoretic Approach

Science.gov (United States)

Rodriguez, Armando A.; Metzger, Richard P.; Cifdaloz, Oguzhan; Dhirasakdanon, Thanate; Welfert, Bruno

2004-01-01

This paper describes an interactive modelling, simulation, animation, and real-time control (MoSART) environment for a class of 'cart-pendulum' electromechanical systems that may be used to enhance learning within differential equations and linear algebra classes. The environment is useful for conveying fundamental mathematical/systems concepts…

Simulation of daily streamflows at gaged and ungaged locations within the Cedar River Basin, Iowa, using a Precipitation-Runoff Modeling System model

Science.gov (United States)

Christiansen, Daniel E.

2012-01-01

The U.S. Geological Survey, in cooperation with the Iowa Department of Natural Resources, conducted a study to examine techniques for estimation of daily streamflows using hydrological models and statistical methods. This report focuses on the use of a hydrologic model, the U.S. Geological Survey's Precipitation-Runoff Modeling System, to estimate daily streamflows at gaged and ungaged locations. The Precipitation-Runoff Modeling System is a modular, physically based, distributed-parameter modeling system developed to evaluate the impacts of various combinations of precipitation, climate, and land use on surface-water runoff and general basin hydrology. The Cedar River Basin was selected to construct a Precipitation-Runoff Modeling System model that simulates the period from January 1, 2000, to December 31, 2010. The calibration period was from January 1, 2000, to December 31, 2004, and the validation periods were from January 1, 2005, to December 31, 2010 and January 1, 2000 to December 31, 2010. A Geographic Information System tool was used to delineate the Cedar River Basin and subbasins for the Precipitation-Runoff Modeling System model and to derive parameters based on the physical geographical features. Calibration of the Precipitation-Runoff Modeling System model was completed using a U.S. Geological Survey calibration software tool. The main objective of the calibration was to match the daily streamflow simulated by the Precipitation-Runoff Modeling System model with streamflow measured at U.S. Geological Survey streamflow gages. The Cedar River Basin daily streamflow model performed with a Nash-Sutcliffe efficiency ranged from 0.82 to 0.33 during the calibration period, and a Nash-Sutcliffe efficiency ranged from 0.77 to -0.04 during the validation period. The Cedar River Basin model is meeting the criteria of greater than 0.50 Nash-Sutcliffe and is a good fit for streamflow conditions for the calibration period at all but one location, Austin, Minnesota

Modeling and simulation for cyber-physical system security research, development and applications.

Energy Technology Data Exchange (ETDEWEB)

Pollock, Guylaine M.; Atkins, William Dee; Schwartz, Moses Daniel; Chavez, Adrian R.; Urrea, Jorge Mario; Pattengale, Nicholas; McDonald, Michael James; Cassidy, Regis H.; Halbgewachs, Ronald D.; Richardson, Bryan T.; Mulder, John C.

2010-02-01

This paper describes a new hybrid modeling and simulation architecture developed at Sandia for understanding and developing protections against and mitigations for cyber threats upon control systems. It first outlines the challenges to PCS security that can be addressed using these technologies. The paper then describes Virtual Control System Environments (VCSE) that use this approach and briefly discusses security research that Sandia has performed using VCSE. It closes with recommendations to the control systems security community for applying this valuable technology.

Proceedings of the 17. IASTED international conference on modelling and simulation

Energy Technology Data Exchange (ETDEWEB)

Wamkeue, R. (comp.) [Quebec Univ., Abitibi-Temiscaminque, PQ (Canada)

2006-07-01

The International Association of Science and Technology for Development (IASTED) hosted this conference to provide a forum for international researchers and practitioners interested in all areas of modelling and simulation. The conference featured 12 sessions entitled: (1) automation, control and robotics, (2) hydraulic and hydrologic modelling, (3) applications in processes and design optimization, (4) environmental systems, (5) biomedicine and biomechanics, (6) communications, computers and informatics 1, (7) economics, management and operations research 1, (8) modelling and simulation methodologies 1, (9) economics, management and operations research 2, (10) modelling, optimization, identification and simulation, (11) communications, computers and informatics 2, and, (12) modelling and simulation methodologies 2. Participants took the opportunity to present the latest research, results, and ideas in mathematical modelling; physically-based modelling; agent-based modelling; dynamic modelling; 3-dimensional modelling; computational geometry; time series analysis; finite element methods; discrete event simulation; web-based simulation; Monte Carlo simulation; simulation optimization; simulation uncertainty; fuzzy systems; data modelling; computer aided design; and, visualization. Case studies in engineering design were also presented along with simulation tools and languages. The conference also highlighted topical issues in environmental systems modelling such as air modelling and simulation, atmospheric modelling, hazardous materials, mobile source emissions, ecosystem modelling, hydrological modelling, aquatic ecosystems, terrestrial ecosystems, biological systems, agricultural modelling, terrain analysis, meteorological modelling, earth system modelling, climatic modelling, and natural resource management. The conference featured 110 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Distributed simulation of large computer systems

International Nuclear Information System (INIS)

Marzolla, M.

2001-01-01

Sequential simulation of large complex physical systems is often regarded as a computationally expensive task. In order to speed-up complex discrete-event simulations, the paradigm of Parallel and Distributed Discrete Event Simulation (PDES) has been introduced since the late 70s. The authors analyze the applicability of PDES to the modeling and analysis of large computer system; such systems are increasingly common in the area of High Energy and Nuclear Physics, because many modern experiments make use of large 'compute farms'. Some feasibility tests have been performed on a prototype distributed simulator

Simulation-based optimization of thermal systems

International Nuclear Information System (INIS)

Jaluria, Yogesh

2009-01-01

This paper considers the design and optimization of thermal systems on the basis of the mathematical and numerical modeling of the system. Many complexities are often encountered in practical thermal processes and systems, making the modeling challenging and involved. These include property variations, complicated regions, combined transport mechanisms, chemical reactions, and intricate boundary conditions. The paper briefly presents approaches that may be used to accurately simulate these systems. Validation of the numerical model is a particularly critical aspect and is discussed. It is important to couple the modeling with the system performance, design, control and optimization. This aspect, which has often been ignored in the literature, is considered in this paper. Design of thermal systems based on concurrent simulation and experimentation is also discussed in terms of dynamic data-driven optimization methods. Optimization of the system and of the operating conditions is needed to minimize costs and improve product quality and system performance. Different optimization strategies that are currently used for thermal systems are outlined, focusing on new and emerging strategies. Of particular interest is multi-objective optimization, since most thermal systems involve several important objective functions, such as heat transfer rate and pressure in electronic cooling systems. A few practical thermal systems are considered in greater detail to illustrate these approaches and to present typical simulation, design and optimization results

Efficient Uplink Modeling for Dynamic System-Level Simulations of Cellular and Mobile Networks

Directory of Open Access Journals (Sweden)

Lobinger Andreas

2010-01-01

Full Text Available A novel theoretical framework for uplink simulations is proposed. It allows investigations which have to cover a very long (real- time and which at the same time require a certain level of accuracy in terms of radio resource management, quality of service, and mobility. This is of particular importance for simulations of self-organizing networks. For this purpose, conventional system level simulators are not suitable due to slow simulation speeds far beyond real-time. Simpler, snapshot-based tools are lacking the aforementioned accuracy. The runtime improvements are achieved by deriving abstract theoretical models for the MAC layer behavior. The focus in this work is long term evolution, and the most important uplink effects such as fluctuating interference, power control, power limitation, adaptive transmission bandwidth, and control channel limitations are considered. Limitations of the abstract models will be discussed as well. Exemplary results are given at the end to demonstrate the capability of the derived framework.

A High-Throughput, High-Accuracy System-Level Simulation Framework for System on Chips

Directory of Open Access Journals (Sweden)

Guanyi Sun

2011-01-01

Full Text Available Today's System-on-Chips (SoCs design is extremely challenging because it involves complicated design tradeoffs and heterogeneous design expertise. To explore the large solution space, system architects have to rely on system-level simulators to identify an optimized SoC architecture. In this paper, we propose a system-level simulation framework, System Performance Simulation Implementation Mechanism, or SPSIM. Based on SystemC TLM2.0, the framework consists of an executable SoC model, a simulation tool chain, and a modeling methodology. Compared with the large body of existing research in this area, this work is aimed at delivering a high simulation throughput and, at the same time, guaranteeing a high accuracy on real industrial applications. Integrating the leading TLM techniques, our simulator can attain a simulation speed that is not slower than that of the hardware execution by a factor of 35 on a set of real-world applications. SPSIM incorporates effective timing models, which can achieve a high accuracy after hardware-based calibration. Experimental results on a set of mobile applications proved that the difference between the simulated and measured results of timing performance is within 10%, which in the past can only be attained by cycle-accurate models.

Modeling and simulation of enzymatic gluconic acid production using immobilized enzyme and CSTR-PFTR circulation reaction system.

Science.gov (United States)

Li, Can; Lin, Jianqun; Gao, Ling; Lin, Huibin; Lin, Jianqiang

2018-04-01

Production of gluconic acid by using immobilized enzyme and continuous stirred tank reactor-plug flow tubular reactor (CSTR-PFTR) circulation reaction system. A production system is constructed for gluconic acid production, which consists of a continuous stirred tank reactor (CSTR) for pH control and liquid storage and a plug flow tubular reactor (PFTR) filled with immobilized glucose oxidase (GOD) for gluconic acid production. Mathematical model is developed for this production system and simulation is made for the enzymatic reaction process. The pH inhibition effect on GOD is modeled by using a bell-type curve. Gluconic acid can be efficiently produced by using the reaction system and the mathematical model developed for this system can simulate and predict the process well.

Simulation Model developed for a Small-Scale PV-System in a Distribution Network

DEFF Research Database (Denmark)

Koch-Ciobotaru, C.; Mihet-Popa, Lucian; Isleifsson, Fridrik Rafn

2012-01-01

This paper presents a PV panel simulation model using the single-diode four-parameter model based on data sheet values. The model was implemented first in MATLAB/Simulink, and the results have been compared with the data sheet values and characteristics of the PV panels in standard test condition...... and implemented in PowerFactory to study load flow, steady-state voltage stability and dynamic behavior of a distributed power system....

A Simulation Approach for Performance Validation during Embedded Systems Design

Science.gov (United States)

Wang, Zhonglei; Haberl, Wolfgang; Herkersdorf, Andreas; Wechs, Martin

Due to the time-to-market pressure, it is highly desirable to design hardware and software of embedded systems in parallel. However, hardware and software are developed mostly using very different methods, so that performance evaluation and validation of the whole system is not an easy task. In this paper, we propose a simulation approach to bridge the gap between model-driven software development and simulation based hardware design, by merging hardware and software models into a SystemC based simulation environment. An automated procedure has been established to generate software simulation models from formal models, while the hardware design is originally modeled in SystemC. As the simulation models are annotated with timing information, performance issues are tackled in the same pass as system functionality, rather than in a dedicated approach.

Modelling and Simulation of a Hydrostatic Steering System for Agricultural Tractors

Directory of Open Access Journals (Sweden)

Barbara Zardin

2018-01-01

Full Text Available The steering system of a vehicle impacts on the vehicle performance, safety and on the driver’s comfort. Moreover, in off-road vehicles using hydrostatic steering systems, the energy dissipation also becomes a critical issue. These aspects push and motivate innovation, research and analysis in the field of agricultural tractors. This paper proposes the modelling and analysis of a hydrostatic steering system for an agricultural tractor to calculate the performance of the system and determine the influence of its main design parameters. The focus here is on the driver’s steering feel, which can improve the driver’s behavior reducing unnecessary steering corrections during the working conditions. The hydrostatic steering system is quite complex and involves a hydraulic circuit and a mechanical mechanism to transmit the steering to the vehicle tires. The detailed lumped parameters model here proposed allows to simulate the dynamic behavior of the steering system and to both enhance the understanding of the system and to improve the design through parameters sensitivity analysis.

FASTBUS simulation models in VHDL

International Nuclear Information System (INIS)

Appelquist, G.

1992-11-01

Four hardware simulation models implementing the FASTBUS protocol are described. The models are written in the VHDL hardware description language to obtain portability, i.e. without relations to any specific simulator. They include two complete FASTBUS devices, a full-duplex segment interconnect and ancillary logic for the segment. In addition, master and slave models using a high level interface to describe FASTBUS operations, are presented. With these models different configurations of FASTBUS systems can be evaluated and the FASTBUS transactions of new devices can be verified. (au)

Towards Better Simulation of US Maize Yield Responses to Climate in the Community Earth System Model

Science.gov (United States)

Peng, B.; Guan, K.; Chen, M.; Lawrence, D. M.; Jin, Z.; Bernacchi, C.; Ainsworth, E. A.; DeLucia, E. H.; Lombardozzi, D. L.; Lu, Y.

2017-12-01

Global food security is undergoing continuing pressure from increased population and climate change despites the potential advancement in breeding and management technologies. Earth system models (ESMs) are essential tools to study the impacts of historical and future climate on regional and global food production, as well as to assess the effectiveness of possible adaptations and their potential feedback to climate. Here we developed an improved maize representation within the Community Earth System Model (CESM) by combining the strengths of both the Community Land Model version 4.5 (CLM4.5) and the Agricultural Production Systems sIMulator (APSIM) models. Specifically, we modified the maize planting scheme, incorporated the phenology scheme adopted from the APSIM model, added a new carbon allocation scheme into CLM4.5, and improved the estimation of canopy structure parameters including leaf area index (LAI) and canopy height. Unique features of the new model (CLM-APSIM) include more detailed phenology stages, an explicit implementation of the impacts of various abiotic environmental stresses (including nitrogen, water, temperature and heat stresses) on maize phenology and carbon allocation, as well as an explicit simulation of grain number and grain size. We conducted a regional simulation of this new model over the US Corn Belt during 1990 to 2010. The simulated maize yield as well as its responses to climate (growing season mean temperature and precipitation) are benchmarked with data from UADA NASS statistics. Our results show that the CLM-APSIM model outperforms the CLM4.5 in simulating county-level maize yield production and reproduces more realistic yield responses to climate variations than CLM4.5. However, some critical processes (such as crop failure due to frost and inundation and suboptimal growth condition due to biotic stresses) are still missing in both CLM-APSIM and CLM4.5, making the simulated yield responses to climate slightly deviate from the

Description of the grout system dynamic simulation

International Nuclear Information System (INIS)

Zimmerman, B.D.

1993-07-01

The grout system dynamic computer simulation was created to allow investigation of the ability of the grouting system to meet established milestones, for various assumed system configurations and parameters. The simulation simulates the movement of tank waste through the system versus time, from initial storage tanks, through feed tanks and the grout plant, then finally to a grout vault. The simulation properly accounts for the following (1) time required to perform various actions or processes, (2) delays involved in gaining regulatory approval, (3) random system component failures, (4) limitations on equipment capacities, (5) available parallel components, and (6) different possible strategies for vault filling. The user is allowed to set a variety of system parameters for each simulation run. Currently, the output of a run primarily consists of a plot of projected grouting campaigns completed versus time, for comparison with milestones. Other outputs involving any model component can also be quickly created or deleted as desired. In particular, sensitivity runs where the effect of varying a model parameter (flow rates, delay times, number of feed tanks available, etc.) on the ability of the system to meet milestones can be made easily. The grout system simulation was implemented using the ITHINK* simulation language for Macintosh** computers

Knowledge mobilisation for policy development: implementing systems approaches through participatory dynamic simulation modelling.

Science.gov (United States)

Freebairn, Louise; Rychetnik, Lucie; Atkinson, Jo-An; Kelly, Paul; McDonnell, Geoff; Roberts, Nick; Whittall, Christine; Redman, Sally

2017-10-02

Evidence-based decision-making is an important foundation for health policy and service planning decisions, yet there remain challenges in ensuring that the many forms of available evidence are considered when decisions are being made. Mobilising knowledge for policy and practice is an emergent process, and one that is highly relational, often messy and profoundly context dependent. Systems approaches, such as dynamic simulation modelling can be used to examine both complex health issues and the context in which they are embedded, and to develop decision support tools. This paper reports on the novel use of participatory simulation modelling as a knowledge mobilisation tool in Australian real-world policy settings. We describe how this approach combined systems science methodology and some of the core elements of knowledge mobilisation best practice. We describe the strategies adopted in three case studies to address both technical and socio-political issues, and compile the experiential lessons derived. Finally, we consider the implications of these knowledge mobilisation case studies and provide evidence for the feasibility of this approach in policy development settings. Participatory dynamic simulation modelling builds on contemporary knowledge mobilisation approaches for health stakeholders to collaborate and explore policy and health service scenarios for priority public health topics. The participatory methods place the decision-maker at the centre of the process and embed deliberative methods and co-production of knowledge. The simulation models function as health policy and programme dynamic decision support tools that integrate diverse forms of evidence, including research evidence, expert knowledge and localised contextual information. Further research is underway to determine the impact of these methods on health service decision-making.

DigR: a generic model and its open source simulation software to mimic three-dimensional root-system architecture diversity.

Science.gov (United States)

Barczi, Jean-François; Rey, Hervé; Griffon, Sébastien; Jourdan, Christophe

2018-04-18

Many studies exist in the literature dealing with mathematical representations of root systems, categorized, for example, as pure structure description, partial derivative equations or functional-structural plant models. However, in these studies, root architecture modelling has seldom been carried out at the organ level with the inclusion of environmental influences that can be integrated into a whole plant characterization. We have conducted a multidisciplinary study on root systems including field observations, architectural analysis, and formal and mathematical modelling. This integrative and coherent approach leads to a generic model (DigR) and its software simulator. Architecture analysis applied to root systems helps at root type classification and architectural unit design for each species. Roots belonging to a particular type share dynamic and morphological characteristics which consist of topological and geometric features. The DigR simulator is integrated into the Xplo environment, with a user interface to input parameter values and make output ready for dynamic 3-D visualization, statistical analysis and saving to standard formats. DigR is simulated in a quasi-parallel computing algorithm and may be used either as a standalone tool or integrated into other simulation platforms. The software is open-source and free to download at http://amapstudio.cirad.fr/soft/xplo/download. DigR is based on three key points: (1) a root-system architectural analysis, (2) root type classification and modelling and (3) a restricted set of 23 root type parameters with flexible values indexed in terms of root position. Genericity and botanical accuracy of the model is demonstrated for growth, branching, mortality and reiteration processes, and for different root architectures. Plugin examples demonstrate the model's versatility at simulating plastic responses to environmental constraints. Outputs of the model include diverse root system structures such as tap

Modeling and Simulation of Truck Engine Cooling System for Onboard Diagnosis

Institute of Scientific and Technical Information of China (English)

朱正礼; 张建武; 包继华

2004-01-01

A cooling system model of a selected internal combustion engine has been built for onboard diagnosis. The model uses driving cycle data available within the production Engine Control Module (ECM): vehicle speed, engine speed, and fuel flow rate for the given ambient temperature and pressure, etc. Based on the conservation laws for heat transfer and mass flow process, the mathematical descriptions for the components involved in the cooling circuit are obtained and all the components are integrated into a model on Matlab/Simulink platform. The model can simulate the characteristics of thermostat (e.g. time-lag, hysteresis effect).The changes of coolant temperature, heat transfer flow rate, and pressure at individual component site are also shown.

Network Modeling and Simulation A Practical Perspective

CERN Document Server

Guizani, Mohsen; Khan, Bilal

2010-01-01

Network Modeling and Simulation is a practical guide to using modeling and simulation to solve real-life problems. The authors give a comprehensive exposition of the core concepts in modeling and simulation, and then systematically address the many practical considerations faced by developers in modeling complex large-scale systems. The authors provide examples from computer and telecommunication networks and use these to illustrate the process of mapping generic simulation concepts to domain-specific problems in different industries and disciplines. Key features: Provides the tools and strate

MHSS: a material handling system simulator

Energy Technology Data Exchange (ETDEWEB)

Pomernacki, L.; Hollstien, R.B.

1976-04-07

A Material Handling System Simulator (MHSS) program is described that provides specialized functional blocks for modeling and simulation of nuclear material handling systems. Models of nuclear fuel fabrication plants may be built using functional blocks that simulate material receiving, storage, transport, inventory, processing, and shipping operations as well as the control and reporting tasks of operators or on-line computers. Blocks are also provided that allow the user to observe and gather statistical information on the dynamic behavior of simulated plants over single or replicated runs. Although it is currently being developed for the nuclear materials handling application, MHSS can be adapted to other industries in which material accountability is important. In this paper, emphasis is on the simulation methodology of the MHSS program with application to the nuclear material safeguards problem. (auth)

Simulation Based Optimization for World Line Card Production System

Directory of Open Access Journals (Sweden)

Sinan APAK

2012-07-01

Full Text Available Simulation based decision support system is one of the commonly used tool to examine complex production systems. The simulation approach provides process modules which can be adjusted with certain parameters by using data relatively easily obtainable in production process. World Line Card production system simulation is developed to evaluate the optimality of existing production line via using discrete event simulation model with variaty of alternative proposals. The current production system is analysed by a simulation model emphasizing the bottlenecks and the poorly utilized production line. Our analysis identified some improvements and efficient solutions for the existing system.

Research in Modeling and Simulation for Airspace Systems Innovation

Science.gov (United States)

Ballin, Mark G.; Kimmel, William M.; Welch, Sharon S.

2007-01-01

This viewgraph presentation provides an overview of some of the applied research and simulation methodologies at the NASA Langley Research Center that support aerospace systems innovation. Risk assessment methodologies, complex systems design and analysis methodologies, and aer ospace operations simulations are described. Potential areas for future research and collaboration using interactive and distributed simula tions are also proposed.

A Simulation and Modeling Framework for Space Situational Awareness

International Nuclear Information System (INIS)

Olivier, S.S.

2008-01-01

This paper describes the development and initial demonstration of a new, integrated modeling and simulation framework, encompassing the space situational awareness enterprise, for quantitatively assessing the benefit of specific sensor systems, technologies and data analysis techniques. The framework is based on a flexible, scalable architecture to enable efficient, physics-based simulation of the current SSA enterprise, and to accommodate future advancements in SSA systems. In particular, the code is designed to take advantage of massively parallel computer systems available, for example, at Lawrence Livermore National Laboratory. The details of the modeling and simulation framework are described, including hydrodynamic models of satellite intercept and debris generation, orbital propagation algorithms, radar cross section calculations, optical brightness calculations, generic radar system models, generic optical system models, specific Space Surveillance Network models, object detection algorithms, orbit determination algorithms, and visualization tools. The use of this integrated simulation and modeling framework on a specific scenario involving space debris is demonstrated

Dynamic Modeling and Simulation of an Isolated Hybrid Power System in a Rural Area of China

Directory of Open Access Journals (Sweden)

Bojian Jiang

2018-01-01

Full Text Available In some rural areas in the northwest of China, people are suffering from not only the voltage drop due to long distance transmission but also the power outages due to remoteness and poorly maintained grid. In recent few years, the price of solar energy has been reduced drastically every year in China due to the government policy on renewable energy. In the near future, isolated hybrid power systems for home use could be affordable and used by residences in these rural areas. Thus, it is necessary to design a hybrid power system based on local load and weather condition to check system feasibility and expected performance. It includes load simulation, system sizing, and dynamic system modeling and simulation. This paper firstly introduces current development of renewable energy in China and then goes through the sizing, modeling, and simulation of the system design for a typical remote home in China and finally discusses the system’s availability based on the simulation results. In this paper, the NASA website is the source for weather data, and BEopt is used to generate load data. During system modeling, the MPPT algorithm is much simpler designed than the complex incremental method. A soft starter is adopted with the diesel generator for stability. The charge controller of the battery storage provides external command to the MPPT and diesel PID controller to prevent the battery storage from overcharging. The rms value of the fundamental load voltage is used in the voltage control loop of the inverter.

Development of the Transport Class Model (TCM) Aircraft Simulation From a Sub-Scale Generic Transport Model (GTM) Simulation

Science.gov (United States)

Hueschen, Richard M.

2011-01-01

A six degree-of-freedom, flat-earth dynamics, non-linear, and non-proprietary aircraft simulation was developed that is representative of a generic mid-sized twin-jet transport aircraft. The simulation was developed from a non-proprietary, publicly available, subscale twin-jet transport aircraft simulation using scaling relationships and a modified aerodynamic database. The simulation has an extended aerodynamics database with aero data outside the normal transport-operating envelope (large angle-of-attack and sideslip values). The simulation has representative transport aircraft surface actuator models with variable rate-limits and generally fixed position limits. The simulation contains a generic 40,000 lb sea level thrust engine model. The engine model is a first order dynamic model with a variable time constant that changes according to simulation conditions. The simulation provides a means for interfacing a flight control system to use the simulation sensor variables and to command the surface actuators and throttle position of the engine model.

Distributed Photovoltaics in the Swedish Energy System. Model Development and Simulations

International Nuclear Information System (INIS)

Widen, Joakim

2009-06-01

Application of photovoltaics (PV) is increasing worldwide, mainly due to extensive subsidy schemes for introducing CO 2 -free power generation. A majority of newly installed systems are distributed small-scale systems located in distribution grids, often at residential customers. Recent developments suggest that such distributed PV generation (PV-DG) could gain more interest in Sweden in the near future. With prospects of decreasing module prices, an extensive integration could be possible. This licentiate thesis presents the first part of a PhD project with the aim to determine the potential for domestic PV-DG in Sweden. Two aspects are treated in detail in the thesis: (1) the ability of PV to match a local domestic power demand and (2) impacts of extensive integration of PV-DG on power flow in low-voltage (LV) distribution grids. To make realistic studies for high-latitude conditions, there is a need for representative demand and PV generation data. As there is a lack of detailed domestic load data in Sweden, a major part of the work has been devoted to development of a stochastic load model. Interdisciplinary studies of household activities were performed to get insight into how domestic electricity use is embedded in the structure of everyday life. It was found that time-use (TU) data, normally used in the social sciences, can be used to model domestic power demand. Both a conversion model for estimating power demand from empirical TU data and a stochastic Markov-chain model for generating synthetic activity patterns and power demand were developed and extensively validated against measurements. Importantly, a realistic model of domestic lighting demand from occupancy patterns and irradiation data was developed, that preserves the negative correlation between irradiation and lighting demand. The models provide a basis for load matching studies and power-flow simulations, but can be used for other purposes as well. Case studies of individual households showed

Distributed Photovoltaics in the Swedish Energy System. Model Development and Simulations

Energy Technology Data Exchange (ETDEWEB)

Widen, Joakim

2009-06-15

Application of photovoltaics (PV) is increasing worldwide, mainly due to extensive subsidy schemes for introducing CO{sub 2}-free power generation. A majority of newly installed systems are distributed small-scale systems located in distribution grids, often at residential customers. Recent developments suggest that such distributed PV generation (PV-DG) could gain more interest in Sweden in the near future. With prospects of decreasing module prices, an extensive integration could be possible. This licentiate thesis presents the first part of a PhD project with the aim to determine the potential for domestic PV-DG in Sweden. Two aspects are treated in detail in the thesis: (1) the ability of PV to match a local domestic power demand and (2) impacts of extensive integration of PV-DG on power flow in low-voltage (LV) distribution grids. To make realistic studies for high-latitude conditions, there is a need for representative demand and PV generation data. As there is a lack of detailed domestic load data in Sweden, a major part of the work has been devoted to development of a stochastic load model. Interdisciplinary studies of household activities were performed to get insight into how domestic electricity use is embedded in the structure of everyday life. It was found that time-use (TU) data, normally used in the social sciences, can be used to model domestic power demand. Both a conversion model for estimating power demand from empirical TU data and a stochastic Markov-chain model for generating synthetic activity patterns and power demand were developed and extensively validated against measurements. Importantly, a realistic model of domestic lighting demand from occupancy patterns and irradiation data was developed, that preserves the negative correlation between irradiation and lighting demand. The models provide a basis for load matching studies and power-flow simulations, but can be used for other purposes as well. Case studies of individual households

Development of Nuclear ship Engineering Simulation SYstem (NESSY)

International Nuclear Information System (INIS)

Kusunoki, Tsuyoshi; Kyouya, Masahiko; Takahashi, Teruo; Kobayashi, Hideo; Ochiai, Masa-aki; Hashidate, Kouji.

1993-11-01

NESSY has been developed for design studies of advanced marine reactors as a part of nuclear ship research and development since 1987. Engineering simulation model of the Mutsu, which is the first nuclear ship in Japan, was completed in March of 1993. In this report we concentration on detail description of softwares for Mutsu modeling. The aims of development of NESSY are as follows; (1) Assessment and confirmation on plant performance of an advanced marine reactor in each step of nuclear ship design (2) Development of abnormality diagnosis system and operator support system as a part of enhanced automization study, and study of human interface with hardware The characteristics of NESSY are the followings. (1) Total engineering simulation system simulate simultaneously ship motions, propulsion system behavior, and nuclear plant behavior under given weather and sea conditions. (2) Models based on physical theory as far as possible. (3) The simulator has high extensibility and flexibility. It is able to apply to other reactors, as the simulation model consists of the part of basic model and the part of plant data which are easy to change. After completion of Mutsu modeling, we are planning to utilize this system as one of design tools for an advanced marine reactor. (author)

Simulation models developed for voltage control in a distribution network using energy storage systems for PV penetration

DEFF Research Database (Denmark)

Mihet-Popa, Lucian; Bindner, Henrik W.

2013-01-01

This paper presents the development of simulation models for DER components in a distribution network, with focus on voltage controllers using energy storage systems for PV penetration. The Vanadium Redox Battery (VRB) system model, used as an energy storage system, was implemented in MATLAB....../Simulink and DIgSILENT PowerFactory, based on the efficiency of different components-such as: cell stacks, electrolytes, pumps and power converters, whilst power losses were also taken into account. The simulation results have been validated against measurements using experimental facility of a distributed power...

Applications and Energy Consumption of Demand Controlled Ventilation Systems. Modelling, Simulation and Implementation of Modular Built Dynamical VAV Systems and Control Strategies

Energy Technology Data Exchange (ETDEWEB)

Soerensen, Bjoern R.

2002-07-01

This thesis discusses many topics of heating and ventilation. This is because the ventilation system is an integrated part of its host building. The functionality and effectiveness of the ventilation system are very much dependent on the building's architectural design, its internal materials, its occupants, its air tightness characteristics and its placement in the terrain. Although this thesis emphasizes strongly on VAV (Variable Air Volume) systems and, in particular, modelling and simulation of such systems, it touches a range of important HVAC related issues. The scope is however, limited to the field of comfort ventilation. That is because ventilation in industrial environments often is subject to separate regulations, and requires other and specialized methods of design and evaluation of ventilation performance. The main objectives have been to: (1) Develop mathematical models for VAV components and systems. (2) Evaluate existing and develop new strategies for VAV demand controlled ventilation by system simulation. (3) Investigate the potential for saving energy and the impact on indoor climate. The development of mathematical models and simulation of VAV systems are given quite much attention compared to the other topics discussed.

Modeling and simulations of a 30 MWe solar electric generating system using parabolic trough collectors in Turkey

Energy Technology Data Exchange (ETDEWEB)

Usta, Yasemin [Anyl Asansor Ltd (Turkey)], email: syusta@gmail.com; Baker, Derek [Middle East Technical University (Turkey)], email: dbaker@metu.edu.tr; Kaftanoglu, Bilgin [Atilim University (Turkey)], email: bilgink@atilim.edu.tr

2011-07-01

With the energy crisis and the increasing concerns about climate change, the interest in concentrating solar power (CSP) systems is growing in Turkey. The aim of this paper is to develop a model of a CSP system using a field of parabolic trough collectors and to assess the predicted performance of the system. A model was developed for a 30MWe solar generating system in Antalya, Turkey, using TRNSYS software, the solar thermal electric components library and information on an existing system in Kramer Junction, California, United States. Annual simulations were then performed for both systems in Antalya and California using weather data. It was found that the predictions were in good agreement with published data. In addition results showed that Antalya's system would generate 30% less than Kramer Junction's system on an annual basis. This paper provides useful information on modeling and simulation of CSP systems.