General Atomic reprocessing pilot plant: description and results of initial testing

International Nuclear Information System (INIS)

1977-12-01

In June 1976 General Atomic completed the construction of a reprocessing head-end cold pilot plant. In the year since then, each system within the head end has been used for experiments which have qualified the designs. This report describes the equipment in the plant and summarizes the results of the initial phase of reprocessing testing

Initial commissioning results from the APS loss monitor system

International Nuclear Information System (INIS)

Patterson, D.R.

1996-01-01

The design of the beam loss monitor system for the Argonne National Laboratory Advanced Photon Source is based on using a number of air dielectric coaxial cables as long ionization chambers. Results to date show that the loss monitor is useful in helping to determine the cause of injection losses and losses large enough to limit circulating currents in the storage ring to short lifetimes. Sensitivities ranging from 13 to 240 pC of charge collected in the injector BTS (booster-to-storage-ring) loss monitor per picocoulomb of loss have been measured, depending on the loss location. These results have been used to predict that the storage ring loss monitor leakage current limit of 10 pA per cable should allow detection of losses resulting in beam lifetimes of 100 hours or less with 100 mA stored beam. Significant DC bias levels associated with the presence of stored beam have been observed. These large bias levels are most likely caused by the loss monitor responding to hard x-ray synchrotron radiation. No such response to synchrotron radiation was observed during earlier tests at SSRL. However, the loss monitor response to average stored beam current in APS has provided a reasonable alternative to the DC current transformer (DCCT) for measuring beam lifetimes

Overview of the initial NSTX experimental results

International Nuclear Information System (INIS)

Ono, M.; Bell, M.; Bell, R.

2001-01-01

The main aim of the National Spherical Torus Experiment (NSTX) is to establish the fusion physics principles of the spherical torus (ST) concept. The NSTX device began plasma operations in February 1999 and the plasma current I p was successfully brought up to the design value of 1 million amperes on December 14, 1999. The planned plasma shaping parameters, κ=1.6-2.2 and δ=0.2-0.4, were achieved in inner limited, single null and double null configurations. The CHI (Coaxial Helicity Injection) and HHFW (High Harmonic Fast Wave) experiments were also initiated. A CHI injected current of 27 kA produced up to 260 kA of toroidal current without using an ohmic solenoid. With an injection of 2.3 MW of HHFW power, using twelve antennas connected to six transmitters, electrons were heated from a central temperature of 400 eV to 900 eV at a central density of 3.5x10 13 cm -3 increasing the plasma energy to 59 kJ and the toroidal beta, β T to 10 %. Finally, the NBI system commenced operation in Sept. 2000. The initial results with two ion sources (P NBI =2.8MW) shows good heating, producing a total plasma stored energy of 90 kJ corresponding to β T ∼18% at a plasma current of 1.1 MA. (author)

Overview of the initial NSTX experimental results

International Nuclear Information System (INIS)

Ono, M.; Bell, M.G.; Bell, R.E.

2001-01-01

The main aim of the National Spherical Torus Experiment (NSTX) is to establish the fusion physics principles of the spherical torus (ST) concept. The NSTX device began plasma operations in February 1999 and the plasma current I p was successfully brought up to the design value of 1 MA on 14 December 1999. The planned plasma shaping parameters, elongation κ=1:6-2.2 and triangularity δ=0:2-0.4, were achieved in inner wall limited, and single null and double null diverted configurations. The coaxial helicity injection (CHI) and high harmonic fast wave (HHFW) experiments were also initiated. CHI current of 27 kA produced up to 260 kA toroidal current without using an ohmic solenoid. With the injection of 2.3 MW of HHFW power, using 12 antennas connected to six transmitters, electrons were heated from a central temperature of 400 eV to 900 eV at a central density of 3.5x10 13 cm 3 , increasing the plasma energy to 59 kJ and the toroidal β, β T , to 10%. The NBI system commenced operation in September 2000. The initial results with two ion sources (P NBI =2:8 MW) show good heating, producing a total plasma stored energy of 90 kJ corresponding to β T ∼18% at a plasma current of 1.1 MA. (author)

Overview of the Initial NSTX Experimental Results

International Nuclear Information System (INIS)

Ono, M.; Bell, M.; Bell, R. E.; Bigelow, T.; Bitter, M.

2000-01-01

The main aim of the National Spherical Torus Experiment (NSTX) is to establish the fusion physics principles of the spherical torus (ST) concept. The NSTX device began plasma operations in February 1999 and the plasma current Ip was successfully brought up to the design value of 1 million amperes on December 14, 1999. The planned plasma shaping parameters, k = 1.6 ± 2.2 and d = 0.2 ± 0.4, were achieved in inner limited, single null and double null configurations. The CHI (Coaxial Helicity Injection) and HHFW (High Harmonic Fast Wave) experiments were also initiated. A CHI injected current of 27 kA produced up to 260 kA of toroidal current without using an ohmic solenoid. With an injection of 2.3 MW of HHFW power, using twelve antennas connected to six transmitters, electrons were heated from a central temperature of 400 eV to 900 eV at a central density of 3.5 x 1013 cm-3 increasing the plasma energy to 59 kJ and the toroidal beta, bT to 10 %. Finally, the NBI system commenced operation in Sept. 2000. The initial results with two ion sources (PNBI = 2.8 MW) shows good heating, producing a total plasma stored energy of 90 kJ corresponding to bT = 18 % at a plasma current of 1.1 MA

Initial results with the Berkeley on-line mass separator-RAMA

International Nuclear Information System (INIS)

Cerny, J.; Moltz, D.M.; Evans, H.C.; Vieira, D.J.; Parry, R.F.; Wouters, J.M.; Gough, R.A.; Zisman, M.S.

1977-11-01

Initial performance is described for a reasonably fast and universal (having little or no chemical selectivity) on-line mass analysis system used to expand capabilities in studying nuclei far from stability. The system is termed RAMA, an acronym for Recoil Atom Mass Analyzer. Basically, this system utilizes the helium-jet method to transport activity to a Sidenius hollow-cathode ion source which is coupled to a mass spectrometer. Initial experiments and planned improvements are discussed. Transport efficiencies of between 10 and 60 percent have routinely been achieved, though the latter is much more typical when conditions are optimized

Recommendations for secure initialization routines in operating systems

OpenAIRE

Dodge, Catherine A.

2004-01-01

Approved for public release; distribution in unlimited. While a necessity of all operating systems, the code that initializes a system can be notoriously difficult to understand. This thesis explores the most common architectures used for bringing an operating system to its initial state, once the operating system gains control from the boot loader. Specifically, the ways in which the OpenBSD and Linux operating systems handle initialization are dissected. With this understanding, a set ...

Atmospheric dynamics and bioregenerative technologies in a soil-based ecological life support system: Initial results from biosphere 2

Science.gov (United States)

Nelson, M.; Dempster, W.; Alvarez-Romo, N.; MacCallum, T.

1994-11-01

Biosphere 2 is the first man-made, soil-based, bioregenerative life support system to be developed and tested. The utilization and amendment of local space resources, e.g. martian soil or lunar regolith, for agricultural and other purposes will be necesary if we are to minimize the requirement for Earth materials in the creation of long-term off-planet bases and habitations. Several of the roles soil plays in Biosphere 2 are 1) for air purification 2) as a key component in created wetland systems to recycle human and animal wastes and 3) as nutrient base for a sustainable agricultural cropping program. Initial results from the Biosphere 2 closure experiment are presented. These include the accelerated cycling rates due to small reservoir sizes, strong diurnal and seasonal fluxes in atmospheric CO2, an unexpected and continuing decline in atmospheric oxygen, overall maintenance of low levels of trace gases, recycling of waste waters through biological regeneration systems, and operation of an agriculture designed to provide diverse and nutritionally adequate diets for the crew members.

Atmospheric dynamics and bioregenerative technologies in a soil-based ecological life support system: initial results from Biosphere 2.

Science.gov (United States)

Nelson, M; Dempster, W; Alvarez-Romo, N; MacCallum, T

1994-11-01

Biosphere 2 is the first man-made, soil-based, bioregenerative life support system to be developed and tested. The utilization and amendment of local space resources, e.g. martian soil or lunar regolith, for agricultural and other purposes will be necessary if we are to minimize the requirement for Earth materials in the creation of long-term off-planet bases and habitations. Several of the roles soil plays in Biosphere 2 are 1) for air purification 2) as a key component in created wetland systems to recycle human and animal wastes and 3) as nutrient base for a sustainable agricultural cropping program. Initial results from the Biosphere 2 closure experiment are presented. These include the accelerated cycling rates due to small reservoir sizes, strong diurnal and seasonal fluxes in atmospheric CO2, an unexpected and continuing decline in atmospheric oxygen, overall maintenance of low levels of trace gases, recycling of waste waters through biological regeneration systems, and operation of an agriculture designed to provide diverse and nutritionally adequate diets for the crew members.

Ground Operations Demonstration Unit for Liquid Hydrogen Initial Test Results

Science.gov (United States)

Notardonato, W. U.; Johnson, W. L.; Swanger, A. M.; Tomsik, T.

2015-01-01

NASA operations for handling cryogens in ground support equipment have not changed substantially in 50 years, despite major technology advances in the field of cryogenics. NASA loses approximately 50% of the hydrogen purchased because of a continuous heat leak into ground and flight vessels, transient chill down of warm cryogenic equipment, liquid bleeds, and vent losses. NASA Kennedy Space Center (KSC) needs to develop energy-efficient cryogenic ground systems to minimize propellant losses, simplify operations, and reduce cost associated with hydrogen usage. The GODU LH2 project has designed, assembled, and started testing of a prototype storage and distribution system for liquid hydrogen that represents an advanced end-to-end cryogenic propellant system for a ground launch complex. The project has multiple objectives including zero loss storage and transfer, liquefaction of gaseous hydrogen, and densification of liquid hydrogen. The system is unique because it uses an integrated refrigeration and storage system (IRAS) to control the state of the fluid. This paper will present and discuss the results of the initial phase of testing of the GODU LH2 system.

The application of PS printing plate with Biimidazole photosensitive initiating systems

International Nuclear Information System (INIS)

Li Lidong; Xu Jinqi; Gao Fang; Yang Yongyuan

1999-01-01

The ultraviolet photosensitive initiating system is composed of 4,4'-bis(N,N'-dimethyl-amino)benzophenone(MK), 2-chlorohexaarylbiimidazole(o-C1-HABI) and a hydrogen donor co-initiator n-dodecyl mercaptan(SH). Under the irradiation by high pressure mercury lamp, the relationship between the photo-polymerization rate of MMA and the concentration of each component of the system, including MK, o-C1-HABI and SH, was studied. The excellent results have been obtained through studying the system's application on PS lithographic printing plate

STUDIES ON VINYL POLYMERIZATION WITH INITIATION SYSTEM CONTAINING AMINE DERIVATIVES

Institute of Scientific and Technical Information of China (English)

QIU Kunyuan; ZHANG Jingyi; FENG Xinde(S. T. Voong)

1983-01-01

Two main types of amine-containing initiation systems were studied in this work. In the case of MMA polymerization initiated by BPO-amine (DMT, DHET, DMA) redox systems, it was found that the polymerization rate and colour stability of the polymer for different amine systems were in the following order: DMT≈DHET＞DMA. Accordingly, BPO-DMT and BPO-DHET are effective initiators. In the case of MEMA polymerization by amine (DMT, DHET, DMA) alone, it was found that the polymerization rate and the percentage of conversion for these different amine systems were in the following order: DMT≥DHET＞DMA. The polymerization rate and the percentage of conversion also increased with the increase of DMT concentration. From the kinetic investigation the rate equation of Rp=K [DMT]1/2 [MEMA]3/2 was obtained, and the overall activation energy of polymerization was calculated to be 34.3 KJ/mol (8.2 Kcal/mol). Moreover, the polymerization of MEMA in the presence of DMT was strongly inhibited by hydroquinone, indicating the polymerization being free radical in nature. From these results, the mechanism of MEMA polymerization initiated by amine was proposed.

Systems Analysis Initiated for All-Electric Aircraft Propulsion

Science.gov (United States)

Kohout, Lisa L.

2003-01-01

A multidisciplinary effort is underway at the NASA Glenn Research Center to develop concepts for revolutionary, nontraditional fuel cell power and propulsion systems for aircraft applications. There is a growing interest in the use of fuel cells as a power source for electric propulsion as well as an auxiliary power unit to substantially reduce or eliminate environmentally harmful emissions. A systems analysis effort was initiated to assess potential concepts in an effort to identify those configurations with the highest payoff potential. Among the technologies under consideration are advanced proton exchange membrane (PEM) and solid oxide fuel cells, alternative fuels and fuel processing, and fuel storage. Prior to this effort, the majority of fuel cell analysis done at Glenn was done for space applications. Because of this, a new suite of models was developed. These models include the hydrogen-air PEM fuel cell; internal reforming solid oxide fuel cell; balance-of-plant components (compressor, humidifier, separator, and heat exchangers); compressed gas, cryogenic, and liquid fuel storage tanks; and gas turbine/generator models for hybrid system applications. Initial mass, volume, and performance estimates of a variety of PEM systems operating on hydrogen and reformate have been completed for a baseline general aviation aircraft. Solid oxide/turbine hybrid systems are being analyzed. In conjunction with the analysis efforts, a joint effort has been initiated with Glenn s Computer Services Division to integrate fuel cell stack and component models with the visualization environment that supports the GRUVE lab, Glenn s virtual reality facility. The objective of this work is to provide an environment to assist engineers in the integration of fuel cell propulsion systems into aircraft and provide a better understanding of the interaction between system components and the resulting effect on the overall design and performance of the aircraft. Initially, three

Initial results from the NSTX Real-Time Velocity diagnostic

Science.gov (United States)

Podesta, M.; Bell, R. E.

2011-10-01

A new diagnostic for fast measurements of plasma rotation through active charge-exchange recombination spectroscopy (CHERS) was installed on NSTX. The diagnostic infers toroidal rotation from carbon ions undergoing charge-exchange with neutrals from a heating Neutral Beam (NB). Each of the 4 channels, distributed along the outer major radius, includes active views intercepting the NB and background views missing the beam. Estimated uncertainties in the measured velocity are system. Signals are acquired on 2 CCD detectors, each controlled by a dedicated PC. Spectra are fitted in real-time through a C++ processing code and velocities are made available to the Plasma Control System for future implementation of feedback on velocity. Results from the initial operation during the 2011 run are discussed, emphasizing the fast dynamics of toroidal rotation, e . g . during L-H mode transition and breaking caused by instabilities and by externally-imposed magnetic perturbations. Work supported by USDOE Contract No. DE-AC02-09CH11466.

Initial results from a prototype whole-body photon-counting computed tomography system.

Science.gov (United States)

Yu, Z; Leng, S; Jorgensen, S M; Li, Z; Gutjahr, R; Chen, B; Duan, X; Halaweish, A F; Yu, L; Ritman, E L; McCollough, C H

X-ray computed tomography (CT) with energy-discriminating capabilities presents exciting opportunities for increased dose efficiency and improved material decomposition analyses. However, due to constraints imposed by the inability of photon-counting detectors (PCD) to respond accurately at high photon flux, to date there has been no clinical application of PCD-CT. Recently, our lab installed a research prototype system consisting of two x-ray sources and two corresponding detectors, one using an energy-integrating detector (EID) and the other using a PCD. In this work, we report the first third-party evaluation of this prototype CT system using both phantoms and a cadaver head. The phantom studies demonstrated several promising characteristics of the PCD sub-system, including improved longitudinal spatial resolution and reduced beam hardening artifacts, relative to the EID sub-system. More importantly, we found that the PCD sub-system offers excellent pulse pileup control in cases of x-ray flux up to 550 mA at 140 kV, which corresponds to approximately 2.5×10 11 photons per cm 2 per second. In an anthropomorphic phantom and a cadaver head, the PCD sub-system provided image quality comparable to the EID sub-system for the same dose level. Our results demonstrate the potential of the prototype system to produce clinically-acceptable images in vivo .

Identification of fractional-order systems with unknown initial values and structure

Energy Technology Data Exchange (ETDEWEB)

Du, Wei, E-mail: duwei0203@gmail.com [Key Laboratory of Advanced Control and Optimization for Chemical Processes, Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Miao, Qingying, E-mail: qymiao@sjtu.edu.cn [School of Continuing Education, Shanghai Jiao Tong University, Shanghai 200030 (China); Tong, Le, E-mail: tongle0328@gmail.com [Faculty of Applied Science and Textiles, The Hong Kong Polytechnic University, Hong Kong (China); Tang, Yang [Key Laboratory of Advanced Control and Optimization for Chemical Processes, Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China)

2017-06-21

In this paper, the identification problem of fractional-order chaotic systems is proposed and investigated via an evolutionary optimization approach. Different with other studies to date, this research focuses on the identification of fractional-order chaotic systems with not only unknown orders and parameters, but also unknown initial values and structure. A group of fractional-order chaotic systems, i.e., Lorenz, Lü, Chen, Rössler, Arneodo and Volta chaotic systems, are set as the system candidate pool. The identification problem of fractional-order chaotic systems in this research belongs to mixed integer nonlinear optimization in essence. A powerful evolutionary algorithm called composite differential evolution (CoDE) is introduced for the identification problem presented in this paper. Extensive experiments are carried out to show that the fractional-order chaotic systems with unknown initial values and structure can be successfully identified by means of CoDE. - Highlights: • Unknown initial values and structure are introduced in the identification of fractional-order chaotic systems; • Only a series of output is utilized in the identification of fractional-order chaotic systems; • CoDE is used for the identification problem and the results are satisfactory when compared with other DE variants.

Design of a digital beam attenuation system for computed tomography. Part II. Performance study and initial results

International Nuclear Information System (INIS)

Szczykutowicz, Timothy P.; Mistretta, Charles A.

2013-01-01

Purpose: The purpose of this work is to present a performance study of the digital beam attenuator (DBA) for implementing fluence field modulated CT (FFMCT) using a simulation framework developed to model the incorporation of the DBA into an existing CT system. Additionally, initial results will be presented using a prototype DBA and the realization of the prototype will be described. To our knowledge, this study represents the first experimental use of a device capable of modulating x-ray fluence as a function of fan angle using a CT geometry. Methods: To realize FFMCT, the authors propose to use a wedge design in which one wedge is held stationary and another wedge is moved over the stationary wedge. Due to the wedge shape, the composite thickness of the two wedges changes as a function of the amount of overlap between the wedges. This design allows for the wedges to modulate the photon fluence incident onto a patient. Using a simulation environment, the effect of changing the number of wedges has on dose, scatter, detector dynamic range, and noise uniformity is explored. Experimental results are presented using a prototype DBA having ten Fe wedges and a c-arm CT system geometry. The experimental DBA results are compared to non-DBA scans using scatter and detector dynamic range as metrics. Both flat field and bowtie filtered CT acquisitions were simulated for comparison with the DBA. Results: Numerical results suggest that substantial gains in noise uniformity and scatter-to-primary ratio (SPR) can be obtained using only seven wedges. After seven wedges, the decrease in noise ununiformity and SPR falls off at a lower rate. Simulations comparing CT acquisitions between flat field, bowtie enabled, and DBA CT acquisitions suggest DBA-FFMCT can reduce dose relative to flat field CT by ≈3 times. A bowtie filter under the same imaging conditions was shown to only allow a dose reduction of 1.65 times. Experimentally, a 10 wedge DBA prototype result showed a SPR

Care initiation area yields dramatic results.

Science.gov (United States)

2009-03-01

The ED at Gaston Memorial Hospital in Gastonia, NC, has achieved dramatic results in key department metrics with a Care Initiation Area (CIA) and a physician in triage. Here's how the ED arrived at this winning solution: Leadership was trained in and implemented the Kaizen method, which eliminates redundant or inefficient process steps. Simulation software helped determine additional space needed by analyzing arrival patterns and other key data. After only two days of meetings, new ideas were implemented and tested.

Experimental Study of Bilinear Initiating System Based on Hard Rock Pile Blasting

Directory of Open Access Journals (Sweden)

Yusong Miao

2017-01-01

Full Text Available It is difficult to use industrial explosives to excavate hard rock and achieve suitable blasting effect due to the low energy utilization rate resulting in large rocks and short blasting footage. Thus, improving the utilization ratio of the explosive energy is important. In this study, a novel bilinear initiation system based on hard rock blasting was proposed to improve the blasting effects. Furthermore, on the basis of the detonation wave collision theory, frontal collision, oblique reflection, and Mach reflection during detonation wave propagation were studied. The results show that the maximum detonation pressure at the Mach reflection point where the incident angle is 46.9° is three times larger than the value of the explosive complete detonation. Then, in order to analyze the crack propagation in different initiation forms, a rock fracture test slot was designed, and the results show that bilinear initiating system can change the energy distribution of explosives. Finally, field experiment was implemented at the hard rock pile blasting engineering, and experimental results show that the present system possesses high explosive energy utilization ratio and low rock fragments size. The results of this study can be used to improve the efficiency in hard rock blasting.

Full-field initialized decadal predictions with the MPI earth system model: an initial shock in the North Atlantic

Science.gov (United States)

Kröger, Jürgen; Pohlmann, Holger; Sienz, Frank; Marotzke, Jochem; Baehr, Johanna; Köhl, Armin; Modali, Kameswarrao; Polkova, Iuliia; Stammer, Detlef; Vamborg, Freja S. E.; Müller, Wolfgang A.

2017-12-01

Our decadal climate prediction system, which is based on the Max-Planck-Institute Earth System Model, is initialized from a coupled assimilation run that utilizes nudging to selected state parameters from reanalyses. We apply full-field nudging in the atmosphere and either full-field or anomaly nudging in the ocean. Full fields from two different ocean reanalyses are considered. This comparison of initialization strategies focuses on the North Atlantic Subpolar Gyre (SPG) region, where the transition from anomaly to full-field nudging reveals large differences in prediction skill for sea surface temperature and ocean heat content (OHC). We show that nudging of temperature and salinity in the ocean modifies OHC and also induces changes in mass and heat transports associated with the ocean flow. In the SPG region, the assimilated OHC signal resembles well OHC from observations, regardless of using full fields or anomalies. The resulting ocean transport, on the other hand, reveals considerable differences between full-field and anomaly nudging. In all assimilation runs, ocean heat transport together with net heat exchange at the surface does not correspond to OHC tendencies, the SPG heat budget is not closed. Discrepancies in the budget in the cases of full-field nudging exceed those in the case of anomaly nudging by a factor of 2-3. The nudging-induced changes in ocean transport continue to be present in the free running hindcasts for up to 5 years, a clear expression of memory in our coupled system. In hindcast mode, on annual to inter-annual scales, ocean heat transport is the dominant driver of SPG OHC. Thus, we ascribe a significant reduction in OHC prediction skill when using full-field instead of anomaly initialization to an initialization shock resulting from the poor initialization of the ocean flow.

Initial results from the Tokapole-II poloidal divertor device

International Nuclear Information System (INIS)

Biddle, A.P.; Dexter, R.N.; Groebner, R.J.; Holly, D.J.; Lipschultz, B.; Phillips, M.W.; Prager, S.C.; Sprott, J.C.

1979-01-01

The latest in a series of internal-ring devices, called Tokapole II, has recently begun operation at the University of Wisconsin. Its purpose is to permit the study of the production and confinement of hot, dense plasmas in either a toroidal octupole (with or without toroidal field) or a tokamak with a four-node poloidal divertor. The characteristics of the device and the results of its initial operation are described here. Quantitative measurements of impurity concentration and radiated power have been made. Poloidal divertor equilibria of square and dee shapes have been produced, and an axisymmetric instability has been observed with the inverse dee. Electron cyclotron resonance heating is used to initiate the breakdown near the axis and to control the initial influx of impurities. A 2-MW RF source at the second harmonic of the ion cyclotron frequency is available and has been used to double the ion temperature when operated at low power with an unoptimized antenna. Initial results of operation as a pure octupole with poloidal Ohmic heating suggest a tokamak-like scaling of density (n proportional to Bsub(p)) and confinement time (tau proportional to n). (author)

Factors to Consider in Selecting an Organisational Improvement Initiative: Survey Results

Directory of Open Access Journals (Sweden)

Mohammad Musli

2017-01-01

Full Text Available Organisations should select the appropriate improvement initiative that will fit with the context of organisation and provide value to the organisation. This paper presents 18 factors to be considered when selecting an organisational improvement initiative. Organisational improvement initiatives are approaches, management systems, tools and/or techniques that can be used for managing and improving organisations, such as Lean, ISO9001, Six Sigma and Improvement Team. A survey was conducted to identify the level of importance of these 18 factors as criteria for selecting an improvement initiative. Purposive sampling was used for this survey involving practitioners, managers, engineers, executives, consultants and/or academicians, who have been involved in the selection and/or implementation of organisational improvement initiatives in Malaysia. Two factors were rated as ‘very high importance’, which involve: (1 The ability to gain top management commitment and support to introduce and implement the initiative successfully, and (2 The initiative is aligned to the vision, mission and/or purpose of the organisation. All these factors can be adopted by the organisations as decision criteria to assist in the selection of the most appropriate improvement initiative based on rational decision making.

Systems scale assessment of the sustainability implications of emerging green initiatives

International Nuclear Information System (INIS)

Tiwary, Abhishek; Namdeo, Anil; Fuentes, Jose; Dore, Anthony; Hu, Xiao-Ming; Bell, Margaret

2013-01-01

This paper demonstrates a systems framework for assessment of environmental impacts from ‘green initiatives’, through a case study of meso-scale, anthropogenic–biogenic interactions. The following cross-sectoral green initiatives, combining the emerging trends in the North East region of the United Kingdom, have been considered – increasing the vegetation cover; decarbonising road transport; decentralising energy production through biomass plants. Two future scenarios are assessed – Baseline 2 020 (projected emissions from realisation of policy instruments); Aggressive 2 020 (additional emissions from realisation of green initiatives). Resulting trends from the Aggressive 2 020 scenario suggest an increase in emissions of pollutant precursors, including biogenic volatile organic compounds and nitrogen dioxide over the base case by up to 20% and 5% respectively. This has implications for enhanced daytime ozone and secondary aerosols formation by up to 15% and over 5% respectively. Associated land cover changes show marginal decrease of ambient temperature but modest reductions in ammonia and ambient particulates. -- Highlights: • A systems scale assessment framework for emerging green initiatives is proposed. • Interactions between urban greenspace, greener vehicles and bioenergy system examined. • Altering future emissions profile enhances synthesis of photochemical precursors. • Incorporating whole-system evaluation deemed vital for well-rounded sustainability. -- Systems scale implication for air pollution was assessed across three sectors of emerging green initiatives-energy, transport and ecosystem

African Health Systems Initiative (AHSI) | IDRC - International ...

International Development Research Centre (IDRC) Digital Library (Canada)

The African Health Systems Initiative (AHSI) is a 10-year Canadian International ... for strengthening African-led health systems and human resources for health. ... IDRC congratulates first cohort of Women in Climate Change Science Fellows.

Fast Initialization of Bubble-Memory Systems

Science.gov (United States)

Looney, K. T.; Nichols, C. D.; Hayes, P. J.

1986-01-01

Improved scheme several orders of magnitude faster than normal initialization scheme. State-of-the-art commercial bubble-memory device used. Hardware interface designed connects controlling microprocessor to bubblememory circuitry. System software written to exercise various functions of bubble-memory system in comparison made between normal and fast techniques. Future implementations of approach utilize E2PROM (electrically-erasable programable read-only memory) to provide greater system flexibility. Fastinitialization technique applicable to all bubble-memory devices.

A Legacy of Leadership and Lessons Learned: Results from the Rural Systemic Initiatives for Improving Mathematics and Science Education

Science.gov (United States)

Harmon, Hobart L.; Smith, Keith

2007-01-01

This report pays tribute to the National Science Foundation's (NSF) Rural Systemic Initiatives (RSIs), an investment of more than $140 million to improve mathematics and science education in some of rural America's most impoverished communities. The report illustrates the impact of NSF's RSI program on a national scale. Each RSI planned a project…

Initial results from the TST-2 spherical tokamak

International Nuclear Information System (INIS)

Takase, Y.; Ejiri, A.; Kasuya, N.

2001-01-01

A new spherical tokamak TST-2 was constructed at the University of Tokyo and started operation in September 1999. Reliable plasma initiation is achieved with typically 1 kW of ECH power at 2.45 GHz. Plasma currents of up to 90 kA and toroidal fields of up to 0.2 T have been achieved during the initial experimental campaign. The ion temperature is typically 100 eV. Internal reconnection events (IREs) are often observed. The internal magnetic field measured at r/a=2/3 indicated growth of fluctuations up to the 4 th harmonic, suggesting the existence of modes with several different mode numbers. In the presence of a toroidal field and a vertically oriented mirror field, noninductively driven currents of order 1 kA were observed with 1 kW of ECH power. The driven current increased with decreasing filling pressure, down to 3x10 -6 torr. A study of high harmonic fast wave (HHFW) excitation and propagation has begun. Initial results indicate highly efficient wave launching. (author)

Initial water quantification results using neutron computed tomography

Science.gov (United States)

Heller, A. K.; Shi, L.; Brenizer, J. S.; Mench, M. M.

2009-06-01

Neutron computed tomography is an important imaging tool in the field of non-destructive testing and in fundamental research for many engineering applications. Contrary to X-rays, neutrons can be attenuated by some light materials, such as hydrogen, but can penetrate many heavy materials. Thus, neutron computed tomography is useful in obtaining important three-dimensional information about a sample's interior structure and material properties that other traditional methods cannot provide. The neutron computed tomography system at the Pennsylvania State University's Radiation Science and Engineering Center is being utilized to develop a water quantification technique for investigation of water distribution in fuel cells under normal conditions. A hollow aluminum cylinder test sample filled with a known volume of water was constructed for purposes of testing the quantification technique. Transmission images of the test sample at different angles were easily acquired through the synthesis of a dedicated image acquisition computer driving a rotary table controller and an in-house developed synchronization software package. After data acquisition, Octopus (version 8.2) and VGStudio Max (version 1.2) were used to perform cross-sectional and three-dimensional reconstructions of the sample, respectively. The initial reconstructions and water quantification results are presented.

Citizen's initiatives and the representative system

International Nuclear Information System (INIS)

Guggenberger, B.; Kempf, U.

1978-01-01

This anthology containing contributions of 19 sociologists is a systematic investigation of the locality, the possibilities and the effective radius of citizen's initiatives under the functional conditions of the parliamentary - representative system. The intellectual and political surroundings, the sociologic context, the institutional, political and judical overall conditions as well as the consequences of this movement for the whole political system of the Federal Republic of Germany. (orig.) [de

Initial results for compressive sensing in electronic support receiver systems

CSIR Research Space (South Africa)

Du Plessis, WP

2011-04-01

Full Text Available determined by the antenna and microwave system comprising the transmitter and receiver, while the instantaneous bandwidth is mainly determined by the Analog-to-Digital Converter (ADC) in the receiver. A radar can thus operate at any frequency within its... Electronic/Electromagnetic Support Measures (ESM) was used historically [1], [2]. Modern ES receiver systems are based on digital receivers allowing powerful signal processing techniques to be used [3], [4]. Recent developments in sampling technology...

Investigation of fast initialization of spacecraft bubble memory systems

Science.gov (United States)

Looney, K. T.; Nichols, C. D.; Hayes, P. J.

1984-01-01

Bubble domain technology offers significant improvement in reliability and functionality for spacecraft onboard memory applications. In considering potential memory systems organizations, minimization of power in high capacity bubble memory systems necessitates the activation of only the desired portions of the memory. In power strobing arbitrary memory segments, a capability of fast turn on is required. Bubble device architectures, which provide redundant loop coding in the bubble devices, limit the initialization speed. Alternate initialization techniques are investigated to overcome this design limitation. An initialization technique using a small amount of external storage is demonstrated.

Initial results for electrochemical dissolution of spent EBR-II fuel

International Nuclear Information System (INIS)

Li, S. X.

1998-01-01

Initial results are reported for the anode behavior of spent metallic nuclear fuel in an electrorefining process. The anode behavior has been characterized in terms of the initial spent fuel composition and the final composition of the residual cladding hulls. A variety of results have been obtained depending on the experimental conditions. Some of the process variables considered are average and maximum cell voltage, average and maximum anode voltage, amount of electrical charge passed (coulombs or amp-hours) during the experiment, and cell resistance. The main goal of the experiments has been the nearly complete dissolution of uranium with the retention of zirconium and noble metal fission products in the cladding hulls. Analysis has shown that the most indicative parameters for determining an endpoint to the process, recognizing the stated goal, are the maximum anode voltage and the amount of electrical charge passed. For the initial experiments reported here, the best result obtained is greater than 98% uranium dissolution with approximately 50% zirconium retention. Noble metal fission product retention appears to be correlated with zirconium retention

Initial water quantification results using neutron computed tomography

Energy Technology Data Exchange (ETDEWEB)

Heller, A.K. [Department of Mechanical and Nuclear Engineering, Pennsylvania State University (United States)], E-mail: axh174@psu.edu; Shi, L.; Brenizer, J.S.; Mench, M.M. [Department of Mechanical and Nuclear Engineering, Pennsylvania State University (United States)

2009-06-21

Neutron computed tomography is an important imaging tool in the field of non-destructive testing and in fundamental research for many engineering applications. Contrary to X-rays, neutrons can be attenuated by some light materials, such as hydrogen, but can penetrate many heavy materials. Thus, neutron computed tomography is useful in obtaining important three-dimensional information about a sample's interior structure and material properties that other traditional methods cannot provide. The neutron computed tomography system at Pennsylvania State University's Radiation Science and Engineering Center is being utilized to develop a water quantification technique for investigation of water distribution in fuel cells under normal conditions. A hollow aluminum cylinder test sample filled with a known volume of water was constructed for purposes of testing the quantification technique. Transmission images of the test sample at different angles were easily acquired through the synthesis of a dedicated image acquisition computer driving a rotary table controller and an in-house developed synchronization software package. After data acquisition, Octopus (version 8.2) and VGStudio Max (version 1.2) were used to perform cross-sectional and three-dimensional reconstructions of the sample, respectively. The initial reconstructions and water quantification results are presented.

Angiographic assessment of initial balloon angioplasty results.

Science.gov (United States)

Gardiner, Geoffrey A; Sullivan, Kevin L; Halpern, Ethan J; Parker, Laurence; Beck, Margaret; Bonn, Joseph; Levin, David C

2004-10-01

To determine the influence of three factors involved in the angiographic assessment of balloon angioplasty-interobserver variability, operator bias, and the definition used to determine success-on the primary (technical) results of angioplasty in the peripheral arteries. Percent stenosis in 107 lesions in lower-extremity arteries was graded by three independent, experienced vascular radiologists ("observers") before and after balloon angioplasty and their estimates were compared with the initial interpretations reported by the physician performing the procedure ("operator") and an automated quantitative computer analysis. Observer variability was measured with use of intraclass correlation coefficients and SD. Differences among the operator, observers, and the computer were analyzed with use of the Wilcoxon signed-rank test and analysis of variance. For each evaluator, the results in this series of lesions were interpreted with three different definitions of success. Estimation of residual stenosis varied by an average range of 22.76% with an average SD of 8.99. The intraclass correlation coefficients averaged 0.59 for residual stenosis after angioplasty for the three observers but decreased to 0.36 when the operator was included as the fourth evaluator. There was good to very good agreement among the three independent observers and the computer, but poor correlation with the operator (P definition of success was used. Significant differences among the operator, the three observers, and the computer were not present when the definition of success was based on less than 50% residual stenosis. Observer variability and bias in the subjective evaluation of peripheral angioplasty can have a significant influence on the reported initial success rates. This effect can be largely eliminated with the use of residual stenosis of less than 50% to define success. Otherwise, meaningful evaluation of angioplasty results will require independent panels of evaluators or

Initial results from the operation of village hybrid systems in Chile

Energy Technology Data Exchange (ETDEWEB)

Holz, R.; Baring-Gould, E.I.; Corbus, D. [and others

1997-08-01

The government of Chile has undertaken a rural electrification program to electrify 75% of the population by the year 2000. Renewable energy is considered within this program, and its application facilitated through a technical cooperation agreement between Chile`s national energy commission (CNE) and the U.S. Department of Energy. In order to introduce isolated mini-grid hybrid wind-energy systems into Chile, three pilot projects were implemented in Region IX. The goal of the pilot systems is to establish renewables as a viable option for rural electrification in the Chilean context. In this paper we report on the first six months of three pilot projects. Presented as background information are brief descriptions of the power systems, data acquisition systems, and the operation and maintenance (O&M) protocols. Analyses of loads, component performance, system operation, and balance of payments for O&M are the primary points presented. Important lessons learned and future plans are also discussed.

Blasting agents and initiation systems

Energy Technology Data Exchange (ETDEWEB)

Fiscor, S.

2000-01-01

Although blasting differs between and within each industry, as a whole, the mines and quarries are making a shift from a purely ammonium nitrate/fuel oil (ANFO) mixture to a blend of emulsion and ANFO on a straight emulsion. Non-electric (shock tube) initiation systems have provided a viable alternative to the electric detonator (blasting cap). Explosives manufacturers are seeing their roles changes to being blasting contractors or consultants rather than just suppliers. The article discusses these trends and gives examples of typical blasting techniques and amounts of blasting agent used at large USA surface coal mines. Electric caps are still used in blasting underground coal. The Ensign Bickford Co. (EBCo) is developing electronic detonators and has been field testing an electronic initiator, the DIGIDET detonator, for the last four years. When commercially available, electronic detonators will be accurate but will come with a hefty price tag. 2 photos.

Cabo Verde telemedicine program: initial results of nationwide implementation.

Science.gov (United States)

Latifi, Rifat; Dasho, Erion; Merrell, Ronald C; Lopes, Miguel; Azevedo, Vanda; Bekteshi, Flamur; Osmani, Kalterina L; Qesteri, Orland; Kucani, Julian; Lecaj, Ismet

2014-11-01

Telemedicine and e-health have been suggested as one solution for closing the health disparity gap between the developed world and the developing world. Yet evidence is lacking from current successful programs in the developing world and, in particular, from sub-Saharan Africa. The primary objective of our study was to present the preliminary results of our efforts in building the Integrated Telemedicine and e-Health Program for Cabo Verde (ITeHP-CV), with an emphasis on initial utilization and results. This is a prospective study of data collected while we worked to establish a fully functional, integrated national telemedicine network and virtual education network in Cabo Verde. We used the International Virtual e-Hospital Foundation strategic approach known as "initiate-build-operate-transfer" over a 26-month period (November 2011-December 2013). We describe herein the five main pillars of this process that have been implemented: (1) capacity building; (2) network development and deployment of equipment; (3) implementation of clinical telemedicine; (4) implementation of activities related to continuing medical education, delivered from within the country and from abroad; and (5) establishment and use of the electronic virtual library. Based on comprehensive technical and medical assessment of the country's needs, 10 fully functional telemedicine centers in all nine inhabited islands of the Republic of Cabo Verde have been established. RESULTS are presented under the five main pillars of capacity building, network deployment, implementation of clinical telemedicine, implementation of continuing medical education activities, and establishment of the electronic virtual library. The ITeHP-CV has been successfully launched, and the initial results are encouraging. The continuity of the program and sustainability are primary goals once the program is transferred fully to the Ministry of Health of Cabo Verde. A long-term follow-up study is required in order to ensure

DART Core/Combustor-Noise Initial Test Results

Science.gov (United States)

Boyle, Devin K.; Henderson, Brenda S.; Hultgren, Lennart S.

2017-01-01

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aero0propulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This presentation gives a brief description of the recently completed DART core combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data was simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant far field, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. An initial assessment shows that the data is of high quality and compares well with results from a quick 2014 feasibility test. Combustor noise components of measured total-noise signatures were educed using a two-signal source-separation method an dare found to occur in the expected frequency range. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Application of the variational iteration method for system of initial value problems delay differential equations

Science.gov (United States)

Yousef, Hamood. M.; Ismail, A. I. B. MD.

2017-08-01

Many attempts have been presented to solve the system of Delay Differential Equations (DDE) with Initial Value Problem. As a result, it has shown difficulties when getting the solution or cannot be solved. In this paper, a Variational Iteration Method is employed to find out an approximate solution for the system of DDE with initial value problems. The example illustrates convenient and an efficiency comparison with the exact solution.

Homestake surface-underground scintillators: Initial results

International Nuclear Information System (INIS)

Cherry, M.L.; Corbato, S.; Daily, T.; Fenyves, E.J.; Kieda, D.; Lande, K.; Lee, C.K.

1986-01-01

The first 70 tons of the 140-ton Large Area Scintillation Detector (LASD) have been operating since Jan. 1985 at a depth of 4850 ft. (4200 m.w.e.) in the Homestake Gold Mine, Lead, S.D. A total of 4 x 10(4) high-energy muons (E sub mu is approx. 2.7 TeV at the surface) have been detected. The remainder of the detector is scheduled to be in operation by the Fall of 1985. In addition, a surface air shower array is under construction. The first 27 surface counters, spaced out over an area of 270' x 500', began running in June, 1985. The LASD performance, the potential of the combined shower array and underground muon experiment for detecting point sources, and the initial results of a search for periodic emission from Cygnus X-3 are discussed

The Mediterranean Moored Multi-sensor Array (M3A: system development and initial results

Directory of Open Access Journals (Sweden)

K. Nittis

Full Text Available Operational forecasting of ocean circulation and marine ecosystem fluctuations requires multi-parametric real-time measurements of physical and biochemical properties. The architecture of a system that is able to provide such measurements from the upper-thermocline layers of the Mediterranean Sea is described here. The system was developed for the needs of the Mediterranean Forecasting System and incorporates state-of-the-art sensors for optical and chemical measurements in the upper 100 m and physical measurements down to 500 m. Independent moorings that communicate via hydro-acoustic modems are hosting the sensors. The satellite data transfer and the large autonomy allow for the operation of the system in any open-ocean site. The system has been in pre-operational use in the Cretan Sea since January 2000. The results of this pilot phase indicate that multi-parametric real-time observations with the M3A system are feasible, if a consistent maintenance and re-calibration program is followed. The main limitations of the present configuration of M3A are related: (a to bio-fouling that primarily affects the turbidity and secondarily affects the other optical sensors, and (b to the limited throughput of the currently used satellite communication system.

Key words. Atmospheric composition and structure (instruments and techniques. Oceanography: general (ocean prediction Oceanography: physical (upper ocean process

The Mediterranean Moored Multi-sensor Array (M3A: system development and initial results

Directory of Open Access Journals (Sweden)

K. Nittis

2003-01-01

Full Text Available Operational forecasting of ocean circulation and marine ecosystem fluctuations requires multi-parametric real-time measurements of physical and biochemical properties. The architecture of a system that is able to provide such measurements from the upper-thermocline layers of the Mediterranean Sea is described here. The system was developed for the needs of the Mediterranean Forecasting System and incorporates state-of-the-art sensors for optical and chemical measurements in the upper 100 m and physical measurements down to 500 m. Independent moorings that communicate via hydro-acoustic modems are hosting the sensors. The satellite data transfer and the large autonomy allow for the operation of the system in any open-ocean site. The system has been in pre-operational use in the Cretan Sea since January 2000. The results of this pilot phase indicate that multi-parametric real-time observations with the M3A system are feasible, if a consistent maintenance and re-calibration program is followed. The main limitations of the present configuration of M3A are related: (a to bio-fouling that primarily affects the turbidity and secondarily affects the other optical sensors, and (b to the limited throughput of the currently used satellite communication system. Key words. Atmospheric composition and structure (instruments and techniques. Oceanography: general (ocean prediction Oceanography: physical (upper ocean process

Do corporate environmental initiatives lead to results in SMEs?

DEFF Research Database (Denmark)

Madsen, Henning; Ulhøi, John Parm

, it is relevant to study the situation between these two stages in order to identify to which extent corporate environmental initiatives actually lead to results and reductions. The research is based on data collected by surveys of industrial companies in Denmark in 1999, 2003, 2007 and 2011. They information...... with previous research demonstrating that companies generally are re-active in their attitude when perceiving stakeholder influence on taking environmental initiative and mainly respond to influence from stakeholders representing authorities, owners or employees. However, the size of the company may have...... a negative influence in some situations. That is, it seems to be easier for smaller companies to achieve an improvement compared to medium-sized companies....

Dual-energy contrast-enhanced digital mammography: initial clinical results

International Nuclear Information System (INIS)

Dromain, Clarisse; Thibault, Fabienne; Tardivon, Anne; Muller, Serge; Rimareix, Francoise; Delaloge, Suzette; Balleyguier, Corinne

2011-01-01

To assess the diagnostic accuracy of Dual-Energy Contrast-Enhanced Digital Mammography (CEDM) as an adjunct to mammography (MX) versus MX alone and versus mammography plus ultrasound (US). 120 women with 142 suspect findings on MX and/or US underwent CEDM. A pair of low- and high-energy images was acquired using a modified full-field digital mammography system. Exposures were taken in MLO at 2 min and in CC at 4 min after the injection of 1.5 ml/kg of an iodinated contrast agent. One reader evaluated MX, US and CEDM images during 2 sessions 1 month apart. Sensitivity, specificity, and area under the ROC curve were estimated. The results from pathology and follow-up identified 62 benign and 80 malignant lesions. Areas under the ROC curves were significantly superior for MX+CEDM than it was for MX alone and for MX+US using BI-RADS. Sensitivity was higher for MX+CEDM than it was for MX (93% vs. 78%; p < 0.001) with no loss in specificity. The lesion size was closer to the histological size for CEDM. All 23 multifocal lesions were correctly detected by MX+CEDM vs. 16 and 15 lesions by MX and US respectively. Initial clinical results show that CEDM has better diagnostic accuracy than mammography alone and mammography+ultrasound. (orig.)

Initial Results From The Micro-pulse Lidar Network (MPL-Net)

Science.gov (United States)

Welton, E. J.; Campbell, J. R.; Berkoff, T. A.; Spinhirne, J. D.; Ginoux, P.

2001-12-01

The micro-pulse lidar system (MPL) was developed in the early 1990s and was the first small, eye-safe, and autonomous lidar built for fulltime monitoring of cloud and aerosol vertical distributions. In 2000, a new project using MPL systems was started at NASA Goddard Space Flight Center. This new project, the Micro-pulse Lidar Network or MPL-Net, was created to provide long-term observations of aerosol and cloud vertical profiles at key sites around the world. This is accomplished using both NASA operated sites and partnerships with other organizations owning MPL systems. The MPL-Net sites are co-located with NASA AERONET sunphotometers to provide aerosol optical depth data needed for calibration of the MPL. In addition to the long-term sites, MPL-Net provides lidar support for a limited number of field experiments and ocean cruises each year. We will present an overview of the MPL-Net project and show initial results from the first two MPL-Net sites at the South Pole and at Goddard Space Flight Center. Observations of dust layers transported from the desert regions of China, across the Pacific Ocean, to the east coast of the United States will also be shown. MPL-Net affiliated instruments were in place at the desert source region in China, on a research vessel in the Sea of Japan, at ARM sites in Alaska and Oklahoma, and finally at our home site in Maryland (GSFC) during the massive dust storms that occurred in April 2001. The MPL observations of dust layers at each location are shown in comparison to dust layers predicted using the Georgia Tech/Goddard Global Ozone Chemistry Aerosol Radiation and Transport model (GOCART). Finally, the MPL-Net project is the primary ground-validation program for the Geo-Science Laser Altimeter System (GLAS) satellite lidar project (launch date 2002). We will present an overview demonstrating how MPL-Net results are used to help prepare the GLAS data processing algorithms and assist in the calibration/validation of the GLAS data

Initial Results from the Micro-pulse Lidar Network (MPL-Net)

Science.gov (United States)

Welton, Ellsworth J.; Campbell, James R.; Berkoff, Timothy A.; Spinhirne, James D.; Ginoux, Paul; Starr, David OC. (Technical Monitor)

2001-01-01

The micro-pulse lidar system (MPL) was developed in the early 1990s and was the first small, eye-safe, and autonomous lidar built for full time monitoring of cloud and aerosol vertical distributions. In 2000, a new project using MPL systems was started at NASA Goddard Space Flight Center. This new project, the Micro-pulse Lidar Network or MPL-Net, was created to provide long-term observations of aerosol and cloud vertical profiles at key sites around the world. This is accomplished using both NASA operated sites and partnerships with other organizations owning MPL systems. The MPL-Net sites are co-located with NASA AERONET sunphotometers to provide aerosol optical depth data needed for calibration of the MPL. In addition to the long-term sites, MPL-Net provides lidar support for a limited number of field experiments and ocean cruises each year. We will present an overview of the MPL-Net project and show initial results from the first two MPL-Net sites at the South Pole and at Goddard Space Flight Center. Observations of dust layers transported from the Gobi desert, across the Pacific Ocean, to the east coast of the United States will also be shown. MPL-Net affiliated instruments were in place at the desert source region in China, on a research vessel in the Sea of Japan, at ARM sites in Alaska and Oklahoma, and finally at our home site in Maryland (GSFC) during the massive dust storms that occurred in April 2001. The MPL observations of dust layers at each location are shown in comparison to dust layers predicted using the Georgia Tech/Goddard Global Ozone Chemistry Aerosol Radiation and Transport model (GOCART). Finally, the MPL-Net project is the primary ground-validation program for the Geo-Science Laser Altimeter System (GLAS) satellite lidar project (launch date 2002). We will present an overview demonstrating how MPL-Net results are used to help prepare the GLAS data processing algorithms and assist in the calibration/validation of the GLAS data products.

Software-Based Student Response Systems: An Interdisciplinary Initiative

Science.gov (United States)

Fischer, Carol M.; Hoffman, Michael S.; Casey, Nancy C.; Cox, Maureen P.

2015-01-01

Colleagues from information technology and three academic departments collaborated on an instructional technology initiative to employ student response systems in classes in mathematics, accounting and education. The instructors assessed the viability of using software-based systems to enable students to use their own devices (cell phones,…

Preliminary fire hazards analysis for W-211, Initial Tank Retrieval Systems

International Nuclear Information System (INIS)

Huckfeldt, R.A.

1995-01-01

A fire hazards analysis (FHA) was performed for Project W-211, Initial Tank Retrieval System (ITRS), at the Department of Energy (DOE) Hanford site. The objectives of this FHA was to determine (1) the fire hazards that expose the Initial Tank Retrieval System or are inherent in the process, (2) the adequacy of the fire-safety features planned, and (3) the degree of compliance of the project with specific fire safety provisions in DOE orders and related engineering codes and standards. The scope included the construction, the process hazards, building fire protection, and site wide fire protection. The results are presented in terms of the fire hazards present, the potential extent of fire damage, and the impact on employees and public safety. This study evaluated the ITRS with respect to its use at Tank 241-SY-101 only

Influence of changes in initial conditions for the simulation of dynamic systems

Energy Technology Data Exchange (ETDEWEB)

Kotyrba, Martin [Department of Informatics and Computers, University of Ostrava, 30 dubna 22, Ostrava (Czech Republic)

2015-03-10

Chaos theory is a field of study in mathematics, with applications in several disciplines including meteorology, sociology, physics, engineering, economics, biology, and philosophy. Chaos theory studies the behavior of dynamical systems that are highly sensitive to initial conditions—a paradigm popularly referred to as the butterfly effect. Small differences in initial conditions field widely diverging outcomes for such dynamical systems, rendering long-term prediction impossible in general. This happens even though these systems are deterministic, meaning that their future behavior is fully determined by their initial conditions, with no random elements involved. In this paperinfluence of changes in initial conditions will be presented for the simulation of Lorenz system.

Initial results from a charge exchange q-diagnostic on TEXT-U

International Nuclear Information System (INIS)

Valanju, P.M.; Duraiappah, L.; Bengtson, R.D.; Karzhavin, Y.; Nikitin, A.

1994-01-01

The authors present initial results from a new q-diagnostic for TEXT-Upgrade. This method is based on using a toroidal array of detectors to determine the plane in which beam-injected neutrals are emitted after two charge-exchange collisions. The potential advantages are low cost, full plasma accessibility, and good time resolution. Their initial series of experiments on TEXT-U established the feasibility of this technique

A Large-Scale Initiative Inviting Patients to Share Personal Fitness Tracker Data with Their Providers: Initial Results.

Directory of Open Access Journals (Sweden)

Joshua M Pevnick

Full Text Available Personal fitness trackers (PFT have substantial potential to improve healthcare.To quantify and characterize early adopters who shared their PFT data with providers.We used bivariate statistics and logistic regression to compare patients who shared any PFT data vs. patients who did not.A patient portal was used to invite 79,953 registered portal users to share their data. Of 66,105 users included in our analysis, 499 (0.8% uploaded data during an initial 37-day study period. Bivariate and regression analysis showed that early adopters were more likely than non-adopters to be younger, male, white, health system employees, and to have higher BMIs. Neither comorbidities nor utilization predicted adoption.Our results demonstrate that patients had little intrinsic desire to share PFT data with their providers, and suggest that patients most at risk for poor health outcomes are least likely to share PFT data. Marketing, incentives, and/or cultural change may be needed to induce such data-sharing.

Initial Results of the SSPX Transient Internal Probe System for Measuring Toroidal Field Profiles

Science.gov (United States)

Holcomb, C. T.; Jarboe, T. R.; Mattick, A. T.; Hill, D. N.; McLean, H. S.; Wood, R. D.; Cellamare, V.

2000-10-01

Lawrence Livermore National Laboratory, Livermore, CA 94550, USA. The Sustained Spheromak Physics Experiment (SSPX) is using a field profile diagnostic called the Transient Internal Probe (TIP). TIP consists of a verdet-glass bullet that is used to measure the magnetic field by Faraday rotation. This probe is shot through the spheromak by a light gas gun at speeds near 2 km/s. An argon laser is aligned along the path of the probe. The light passes through the probe and is retro-reflected to an ellipsometer that measures the change in polarization angle. The measurement is spatially resolved down to the probes’ 1 cm length to within 15 Gauss. Initial testing results are given. This and future data will be used to determine the field profile for equilibrium reconstruction. TIP can also be used in conjunction with wall probes to map out toroidal mode amplitudes and phases internally. This work was performed under the auspices of US DOE by the University of California Lawrence Livermore National Laboratory under Contract No. W-7405-ENG-48.

Initial tank calibration at NUCEF critical facility. 1. Measurement procedure and its result

International Nuclear Information System (INIS)

Yanagisawa, Hiroshi; Mineo, Hideaki; Tonoike, Kotaro; Takeshita, Isao; Hoshi, Katsuya; Hagiwara, Hiroyuki.

1994-07-01

Initial tank calibrations were carried out prior to hot operation of critical facilities in NUCEF: Nuclear Fuel Cycle Safety Engineering Research Facility, for the purpose of the nuclear material accountancy and control for the facility. Raw calibration data were collected from single run per one tank by measuring differential pressure with dip-tube systems, weight of calibration liquid (demineralized water) poured into the tank, temperature in the tank and so on, without operation of tank ventilation system. Volume and level data were obtained by applying density and buoyancy corrections to the raw data. As a result, the evaluated measurement errors of volume and level were small enough, e.g. within 0.2 lit. and 1.0 mm, respectively, for Pu accountancy tanks. This paper summarizes the above-mentioned measurement procedures, collected data, data correction procedures and evaluated measurement errors. (author)

Selection of initial events of accelerator driven subcritical system

International Nuclear Information System (INIS)

Wang Qianglong; Hu Liqin; Wang Jiaqun; Li Yazhou; Yang Zhiyi

2013-01-01

The Probabilistic Safety Assessment (PSA) is an important tool in reactor safety analysis and a significant reference to the design and operation of reactor. It is the origin and foundation of the PSA for a reactor to select the initial events. Accelerator Driven Subcritical System (ADS) has advanced design characteristics, complicated subsystems and little engineering and operating experience, which makes it much more difficult to identify the initial events of ADS. Based on the current design project of ADS, the system's safety characteristics and special issues were analyzed in this article. After a series of deductions with Master Logic Diagram (MLD) and considering the relating experience of other advanced research reactors, a preliminary initial events was listed finally, which provided the foundation for the next safety assessment. (authors)

Influencing Factors of the Initiation Point in the Parachute-Bomb Dynamic Detonation System

Science.gov (United States)

Qizhong, Li; Ye, Wang; Zhongqi, Wang; Chunhua, Bai

2017-12-01

The parachute system has been widely applied in modern armament design, especially for the fuel-air explosives. Because detonation of fuel-air explosives occurs during flight, it is necessary to investigate the influences of the initiation point to ensure successful dynamic detonation. In fact, the initiating position exist the falling area in the fuels, due to the error of influencing factors. In this paper, the major influencing factors of initiation point were explored with airdrop and the regularity between initiation point area and factors were obtained. Based on the regularity, the volume equation of initiation point area was established to predict the range of initiation point in the fuel. The analysis results showed that the initiation point appeared area, scattered on account of the error of attitude angle, secondary initiation charge velocity, and delay time. The attitude angle was the major influencing factors on a horizontal axis. On the contrary, secondary initiation charge velocity and delay time were the major influencing factors on a horizontal axis. Overall, the geometries of initiation point area were sector coupled with the errors of the attitude angle, secondary initiation charge velocity, and delay time.

Healthy competition drives success in results-based aid: Lessons from the Salud Mesoamérica Initiative.

Science.gov (United States)

El Bcheraoui, Charbel; Palmisano, Erin B; Dansereau, Emily; Schaefer, Alexandra; Woldeab, Alexander; Moradi-Lakeh, Maziar; Salvatierra, Benito; Hernandez-Prado, Bernardo; Mokdad, Ali H

2017-01-01

The Salud Mesoamérica Initiative (SMI) is a three-operation strategy, and is a pioneer in the world of results-based aid (RBA) in terms of the success it has achieved in improving health system inputs following its initial operation. This success in meeting pre-defined targets is rare in the world of financial assistance for health. We investigated the influential aspects of SMI that could have contributed to its effectiveness in improving health systems, with the aim of providing international donors, bilateral organizations, philanthropies, and recipient countries with new perspectives that can help increase the effectiveness of future assistance for health, specifically in the arena of RBA. Qualitative methods based on the criteria of relevance and effectiveness proposed by the Development Assistance Committee of the Organization for Economic Co-operation and Development. Our methods included document review, key informant interviews, a focus group discussion, and a partnership analysis. A purposive sample of 113 key informants, comprising donors, representatives from the Inter-American Development Bank, ministries of health, technical assistance organizations, evaluation organizations, and health care providers. During May-October 2016, we interviewed regarding the relevance and effectiveness of SMI. Themes emerged relative to the topics we investigated, and covered the design and the drivers of success of the initiative. The success is due to 1) the initiative's regional approach, which pressured recipient countries to compete toward meeting targets, 2) a robust and flexible design that incorporated the richness of input from stakeholders at all levels, 3) the design-embedded evaluation component that created a culture of accountability among recipient countries, and 4) the reflective knowledge environment that created a culture of evidence-based decision-making. A regional approach involving all appropriate stakeholders, and based on knowledge sharing and

Policies and initiatives for carbon neutrality in nordic heating and transport systems

DEFF Research Database (Denmark)

Muller, Jakob Glarbo; Wu, Qiuwei; Ostergaard, Jacob

2012-01-01

Policies and initiatives promoting carbon neutrality in the Nordic heating and transport systems are presented. The focus within heating systems is the propagation of heat pumps while the focus within transport systems is initiatives regarding electric vehicles (EVs). It is found that conversion...... to heat pumps in the Nordic region rely on both private economic and national economic incentives. Initiatives toward carbon neutrality in the transport system are mostly concentrated on research, development and demonstration for deployment of a large number of EVs. All Nordic countries have plans...... for the future heating and transport systems with the ambition of realizing carbon neutrality....

Mass Medication Clinic (MMC) Patient Medical Assistant (PMA) System Training Initiative

Science.gov (United States)

2007-06-01

AD_________________ Award Number: W81XWH-06-2-0045 TITLE: Mass Medication Clinic (MMC) Patient ...SUBTITLE 5a. CONTRACT NUMBER Mass Medication Clinic (MMC) Patient Medical Assistant (PMA) System Training Initiative 5b. GRANT NUMBER W81XWH-06-2...sections will describe the events, results, and accomplishments of this study. With validation through this project the Patient Medical Assistant

On the importance of an accurate representation of the initial state of the system in classical dynamics simulations

Science.gov (United States)

García-Vela, A.

2000-05-01

A definition of a quantum-type phase-space distribution is proposed in order to represent the initial state of the system in a classical dynamics simulation. The central idea is to define an initial quantum phase-space state of the system as the direct product of the coordinate and momentum representations of the quantum initial state. The phase-space distribution is then obtained as the square modulus of this phase-space state. The resulting phase-space distribution closely resembles the quantum nature of the system initial state. The initial conditions are sampled with the distribution, using a grid technique in phase space. With this type of sampling the distribution of initial conditions reproduces more faithfully the shape of the original phase-space distribution. The method is applied to generate initial conditions describing the three-dimensional state of the Ar-HCl cluster prepared by ultraviolet excitation. The photodissociation dynamics is simulated by classical trajectories, and the results are compared with those of a wave packet calculation. The classical and quantum descriptions are found in good agreement for those dynamical events less subject to quantum effects. The classical result fails to reproduce the quantum mechanical one for the more strongly quantum features of the dynamics. The properties and applicability of the phase-space distribution and the sampling technique proposed are discussed.

DYE-SENSITIZED PHOTOPOLYMERIZATION OF METHYL METHACRYLATE INITIATED BY COUMARIN DYE/IODONIUM SALT SYSTEM

Institute of Scientific and Technical Information of China (English)

Fang Gao; Yong-yuan Yang

1999-01-01

The photosensitive initiating system composed of 7-diethylamino-3-(2'-benzimidazolyl)coumarin dye (DEDC) and diphenyliodonium hexafluorophosphate (DIHP) which act as the sensitizer and the initiator respectively, can be used to initiate the polymerization of methyl methacrylate (MMA). The results showed that when exposed to visible light, coumarin dye/iodonium salt undergoes quick electron transfer from DEDC to DIHP and free radicals are produced. The visible light photoinduced reaction between DEDC and DIHP is mainly through the excited singlet state of DEDC and thus it is a little sensitive to O2. The influence of concentration of DEDC, DIHP and MMA on the rate of photopolymerization of MMA was also investigated.

Federating clinical data from six pediatric hospitals: process and initial results for microbiology from the PHIS+ consortium.

Science.gov (United States)

Gouripeddi, Ramkiran; Warner, Phillip B; Mo, Peter; Levin, James E; Srivastava, Rajendu; Shah, Samir S; de Regt, David; Kirkendall, Eric; Bickel, Jonathan; Korgenski, E Kent; Precourt, Michelle; Stepanek, Richard L; Mitchell, Joyce A; Narus, Scott P; Keren, Ron

2012-01-01

Microbiology study results are necessary for conducting many comparative effectiveness research studies. Unlike core laboratory test results, microbiology results have a complex structure. Federating and integrating microbiology data from six disparate electronic medical record systems is challenging and requires a team of varied skills. The PHIS+ consortium which is partnership between members of the Pediatric Research in Inpatient Settings (PRIS) network, the Children's Hospital Association and the University of Utah, have used "FURTHeR' for federating laboratory data. We present our process and initial results for federating microbiology data from six pediatric hospitals.

A Community-Level Initiative to Prevent Obesity: Results From Kaiser Permanente's Healthy Eating Active Living Zones Initiative in California.

Science.gov (United States)

Cheadle, Allen; Atiedu, Akpene; Rauzon, Suzanne; Schwartz, Pamela M; Keene, Laura; Davoudi, Mehrnaz; Spring, Rebecca; Molina, Michelle; Lee, Lynda; Boyle, Kathryn; Williamson, Dana; Steimberg, Clara; Tinajero, Roberta; Ravel, Jodi; Nudelman, Jean; Azuma, Andrea Misako; Kuo, Elena S; Solomon, Loel

2018-05-01

A growing number of health systems are leading health promotion efforts in their wider communities. What impact are these efforts having on health behaviors and ultimately health status? This paper presents evaluation results from the place-based Kaiser Permanente Healthy Eating Active Living Zones obesity prevention initiative, implemented in 2011-2015 in 12 low-income communities in Kaiser Permanente's Northern and Southern California Regions. The Healthy Eating Active Living Zones design targeted places and people through policy, environmental, and programmatic strategies. Each Healthy Eating Active Living Zone is a small, low-income community of 10,000 to 20,000 residents with high obesity rates and other health disparities. Community coalitions planned and implemented strategies in each community. A population-dose approach and pre and post surveys were used to assess impact of policy, program, and environmental change strategies; the analysis was conducted in 2016. Population dose is the product of reach (number of people affected by a strategy divided by target population size) and strength (the effect size or relative change in behavior for each person exposed to the strategy). More than 230 community change strategies were implemented over 3 years, encompassing policy, environmental, and programmatic changes as well as efforts to build community capacity to sustain strategies and make changes in the future. Positive population-level results were seen for higher-dose strategies, particularly those targeting youth physical activity. Higher-dose strategies were more likely to be found in communities with the longest duration of investment. These results demonstrate that strong (high-dose), community-based obesity prevention strategies can lead to improved health behaviors, particularly among youth in school settings. This article is part of a supplement entitled Building Thriving Communities Through Comprehensive Community Health Initiatives, which is

Marshall Space Flight Center Propulsion Systems Department (PSD) Knowledge Management (KM) Initiative

Science.gov (United States)

Caraccioli, Paul; Varnedoe, Tom; Smith, Randy; McCarter, Mike; Wilson, Barry; Porter, Richard

2006-01-01

: executive and senior management sponsorship, KM awareness, promotion and training, cultural change management, process improvement, leveraging existing resources and new innovative technologies to align with other NASA KM initiatives (convergence: the big picture). To enable results based incremental implementation and future growth of the KM initiative, key performance measures have been identified including stakeholder value, system utility, learning and growth (knowledge capture, sharing, reduced anomaly recurrence), cultural change, process improvement and return-on-investment. The next steps for the initial implementation spiral (focused on SSME Turbomachinery) have been identified, largely based on the organization and compilation of summary level engineering process models, data capture matrices, functional models and conceptual-level svstems architecture. Key elements include detailed KM requirements definition, KM technology architecture assessment, - evaluation and selection, deployable KM Pilot design, development, implementation and evaluation, and justifying full implementation (estimated Return-on-Investment). Features identified for the notional system architecture include the knowledge presentation layer (and its components), knowledge network layer (and its components), knowledge storage layer (and its components), User Interface and capabilities. This paper provides a snapshot of the progress to date, the near term planning for deploying the KM pilot project and a forward look at results based growth of KM capabilities with-in the MSFC PSD.

Comparison of robust H∞ filter and Kalman filter for initial alignment of inertial navigation system

Institute of Scientific and Technical Information of China (English)

HAO Yan-ling; CHEN Ming-hui; LI Liang-jun; XU Bo

2008-01-01

There are many filtering methods that can be used for the initial alignment of an integrated inertial navigation system.This paper discussed the use of GPS,but focused on two kinds of filters for the initial alignment of an integrated strapdown inertial navigation system (SINS).One method is based on the Kalman filter (KF),and the other is based on the robust filter.Simulation results showed that the filter provides a quick transient response and a little more accurate estimate than KF,given substantial process noise or unknown noise statistics.So the robust filter is an effective and useful method for initial alignment of SINS.This research should make the use of SINS more popular,and is also a step for further research.

Evolution of the Orszag-Tang vortex system in a compressible medium. I - Initial average subsonic flow

Science.gov (United States)

Dahlburg, R. B.; Picone, J. M.

1989-01-01

The results of fully compressible, Fourier collocation, numerical simulations of the Orszag-Tang vortex system are presented. The initial conditions for this system consist of a nonrandom, periodic field in which the magnetic and velocity field contain X points but differ in modal structure along one spatial direction. The velocity field is initially solenoidal, with the total initial pressure field consisting of the superposition of the appropriate incompressible pressure distribution upon a flat pressure field corresponding to the initial, average Mach number of the flow. In these numerical simulations, this initial Mach number is varied from 0.2-0.6. These values correspond to average plasma beta values ranging from 30.0 to 3.3, respectively. It is found that compressible effects develop within one or two Alfven transit times, as manifested in the spectra of compressible quantities such as the mass density and the nonsolenoidal flow field. These effects include (1) a retardation of growth of correlation between the magnetic field and the velocity field, (2) the emergence of compressible small-scale structure such as massive jets, and (3) bifurcation of eddies in the compressible flow field. Differences between the incompressible and compressible results tend to increase with increasing initial average Mach number.

Site Specific Advisory Board initiative, evaluation survey results supplementary appendix: Summary of individual site results

International Nuclear Information System (INIS)

1996-08-01

This Appendix presents results of the Site-Specific Advisory Board (SSAB) Initiative for each of the 11 sites that participated in the survey. These individual results are a supplement to the June 1996 Summary Report which presented overall survey results. Results are presented in 11 sections, arranged alphabetically by site. Each section includes a series of figures and tables that parallel those presented in the Summary Report. To facilitate comparison, figures are presented both for the individual site and for the overall long survey. The sequence of sections is: Fernald, Hanford, Idaho, Los Alamos, Monticello, Nevada, Pantex, Rocky Flats, St. Louis, Sandia, and Savannah River

Reciprocating magnetic refrigerator for 2--4 K operation: Initial results

International Nuclear Information System (INIS)

Barclay, J.A.; Moze, O.; Paterson, L.

1979-01-01

The basic theory and design of a reciprocating magnetic refrigerator to pump heat from 2.2 to 4.2 K is presented. The results of initial experiments are shown. These results include conduction losses, eddy current losses, frictional losses, and mixing losses. Two cooling cycles were attempted and a net cooling power of 52 mW was observed at 1/60 Hz. The key problems in this design are identified and discussed

Dynamics of harmonically-confined systems: Some rigorous results

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhigang, E-mail: zwu@physics.queensu.ca; Zaremba, Eugene, E-mail: zaremba@sparky.phy.queensu.ca

2014-03-15

In this paper we consider the dynamics of harmonically-confined atomic gases. We present various general results which are independent of particle statistics, interatomic interactions and dimensionality. Of particular interest is the response of the system to external perturbations which can be either static or dynamic in nature. We prove an extended Harmonic Potential Theorem which is useful in determining the damping of the centre of mass motion when the system is prepared initially in a highly nonequilibrium state. We also study the response of the gas to a dynamic external potential whose position is made to oscillate sinusoidally in a given direction. We show in this case that either the energy absorption rate or the centre of mass dynamics can serve as a probe of the optical conductivity of the system. -- Highlights: •We derive various rigorous results on the dynamics of harmonically-confined atomic gases. •We derive an extension of the Harmonic Potential Theorem. •We demonstrate the link between the energy absorption rate in a harmonically-confined system and the optical conductivity.

Macrophage Activation Syndrome as Initial Presentation of Systemic Lupus Erythematosus

Directory of Open Access Journals (Sweden)

Say-Tin Yeap

2008-04-01

Full Text Available Macrophage activation syndrome (MAS is known to be a severe and potentially life-threatening complication of rheumatic disorder, especially systemic juvenile rheumatoid arthritis. It is very rare for MAS to be an initial presentation of systemic lupus erythematosus (SLE. Here, we report a 14-year-old girl in whom MAS developed as an initial presentation of SLE. With early diagnosis and administration of cyclosporine A, she had a fair outcome. Further testing showed positive anti-dsDNA about 8 months later.

Expert system for the CPCS-initiated trip analysis

International Nuclear Information System (INIS)

Sohn, Sedo; Im, Inyoung; Kuh, Jungeui

1991-01-01

In Yonggwang nuclear units 3 and 4, the core protection calculator system (CPCS) performs various protection logics against many transients and certain accidents. The CPCS is a real-time computer system calculating the departure from nucleate boiling ratio (DNBR), and local power density, and other protection logics. It takes process variables such as neutron flux, hot-leg temperature, cold-leg temperature, control element assembly positions, and reactor coolant pump shaft speed. Since the CPCS protection logics are quite complex, it is difficult for an operator to tell immediately which parameter is the major cause of the reactor trip. Thus, whenever the reactor trip signal is generated, the process input variables and calculated results, including selected intermediate variables, are frozen in the specified computer memory for later analysis. These frozen variables are called the trip buffer. Analysis of the trip buffer requires an expert in the CPCS and related documents containing algorithms and a data base for algorithms. The Trip Buffer Analysis Program (TBAP) is an expert system that pinpoints the causes of the CPCS initiated reactor trip, thus relieving the operator from the burden of analyzing the trip buffer

Distributed Pair Programming Using Collaboration Scripts: An Educational System and Initial Results

Science.gov (United States)

Tsompanoudi, Despina; Satratzemi, Maya; Xinogalos, Stelios

2015-01-01

Since pair programming appeared in the literature as an effective method of teaching computer programming, many systems were developed to cover the application of pair programming over distance. Today's systems serve personal, professional and educational purposes allowing distributed teams to work together on the same programming project. The…

DESTRUCTIVE LESIONS OF BONES AS A RESULT OF MYCOBACTERIAL PROCESS IN CHILDREN WITH INITIAL IMMUNODEFICIENCIES (CLINICAL, DIAGNOSTICAL AND TACTIC PECULIARITIES

Directory of Open Access Journals (Sweden)

A.Yu. Mushkin

2011-01-01

Full Text Available Initial immunodeficiencies are genetically conditioned defects of immune system; they are the basis for generalized infections including those induced by mycobacteria of tuberculosis complex. The lesions of skeleton in those patients are of different types depending on the kind of immunodeficiency. The article presents the results of clinical observation, conservative and surgical treatment of 12 children with mycobacterial lesions of skeleton on the ground different initial immunodeficiencies — severe combined immune deficiency, chronic granulematosis and insufficiency of interferon and interleukin 12.Key words: children, initial immunodeficiency, mycobacterial infection, bone lesions, surgical treatment.(Voprosy sovremennoi pediatrii — Current Pediatrics. 2011; 10 (3: 60–64

EARLY DYNAMICAL EVOLUTION OF THE SOLAR SYSTEM: PINNING DOWN THE INITIAL CONDITIONS OF THE NICE MODEL

International Nuclear Information System (INIS)

Batygin, Konstantin; Brown, Michael E.

2010-01-01

In the recent years, the 'Nice' model of solar system formation has attained an unprecedented level of success in reproducing much of the observed orbital architecture of the solar system by evolving the planets to their current locations from a more compact configuration. Within the context of this model, the formation of the classical Kuiper Belt requires a phase during which the ice giants have a high eccentricity. An outstanding question of this model is the initial configuration from which the solar system started out. Recent work has shown that multi-resonant initial conditions can serve as good candidates, as they naturally prevent vigorous type-II migration. In this paper, we use analytical arguments, as well as self-consistent numerical N-body simulations to identify fully resonant initial conditions, whose dynamical evolution is characterized by an eccentric phase of the ice giants, as well as planetary scattering. We find a total of eight such initial conditions. Four of these primordial states are compatible with the canonical 'Nice' model, while the others imply slightly different evolutions. The results presented here should prove useful in further development of a comprehensive model for solar system formation.

ERNIE performance with TSA portals Initial Results

Energy Technology Data Exchange (ETDEWEB)

Labov, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2018-01-05

This project extends the “Enhanced Radiological Nuclear Inspection and Evaluation” (ERNIE) system developed with CBP and DNDO to improve performance of PVT-based Radiation Portal Monitors (RPMs). ERNIE was designed to be used with any RPM system. The first implementation was with the SAIC (Leidos) RPM-8 systems. In this project, we are demonstrating how effective the ERNIE approach can be when applied to the VM250 TSA portals used in NSDD programs. Part of the challenge in adapting ERNIE to handle VM250 portals is the lack of gamma spectral information. We report here on the first results showing how the ERNIE analysis can improve analysis of measurements with the VM250 RPMs.

REXEBTS, design and initial commissioning results

CERN Document Server

Wenander, F; Jonson, B; Liljeby, L; Nyman, G H; Rensfelt, K G; Skeppstedt, Ö; Wolf, B

2001-01-01

The REXEDIS is an Electron Beam Ion Source (EBIS) developed particularly for charge breeding of rare and short-lived isotopes produced at ISOLDE for the REX-ISOLDE post accelerator. Bunches of singly charged radioactive ions are injected into the EBIS and charge bred to a charge-to-mass ratio of approximately 1/4 and thereafter extracted and injected into a short LINAC. This novel concept, employing a Penning trap to bunch and cool the ions from an on-line mass separator prior to charge breeding in an EBIS, results in an efficient and compact system. In this article the final REXEBIS design is presented together with results from the first tests. (19 refs).

Understanding managerial behaviour during initial steps of a clinical information system adoption.

Science.gov (United States)

Rodríguez, Charo; Pozzebon, Marlei

2011-06-17

While the study of the information technology (IT) implementation process and its outcomes has received considerable attention, the examination of pre-adoption and pre-implementation stages of configurable IT uptake appear largely under-investigated. This paper explores managerial behaviour during the periods prior the effective implementation of a clinical information system (CIS) by two Canadian university multi-hospital centers. Adopting a structurationist theoretical stance and a case study research design, the processes by which CIS managers' patterns of discourse contribute to the configuration of the new technology in their respective organizational contexts were longitudinally examined over 33 months. Although managers seemed to be aware of the risks and organizational impact of the adoption of a new clinical information system, their decisions and actions over the periods examined appeared rather to be driven by financial constraints and power struggles between different groups involved in the process. Furthermore, they largely emphasized technological aspects of the implementation, with organizational dimensions being put aside. In view of these results, the notion of 'rhetorical ambivalence' is proposed. Results are further discussed in relation to the significance of initial decisions and actions for the subsequent implementation phases of the technology being configured. Theoretical and empirically grounded, the paper contributes to the underdeveloped body of literature on information system pre-implementation processes by revealing the crucial role played by managers during the initial phases of a CIS adoption.

FPGA based, DSP integrated, 8-channel SIMCON, ver. 3.0. Initial results for 8-channel algorithm

Energy Technology Data Exchange (ETDEWEB)

Giergusiewicz, W.; Koprek, W.; Jalmuzna, W.; Pozniak, K.T.; Romaniuk, R.S. [Warsaw Univ. of Technology (Poland). Inst. of Electronic Systems

2005-07-01

The paper describes design, construction and initial measurements of an eight channel electronic LLRF device predicted for building of the control system for the VUV-FEL accelerator at DESY (Hamburg). The device, referred in the paper to as the SIMCON 3.0 (from the SC cavity simulator and controller) consists of a 16 layer, VME size, PCB, a large FPGA chip (VirtexII-4000 by Xilinx), eight fast ADCs and four DACs (by Analog Devices). To our knowledge, the proposed device is the first of this kind for the accelerator technology in which there was achieved (the FPGA based) DSP latency below 200 ns. With the optimized data transmission system, the overall LLRF system latency can be as low as 500 ns. The SIMCON 3.0 sub-system was applied for initial tests with the ACC1 module of the VUV FEL accelerator (eight channels) and with the CHECHIA test stand (single channel), both at the DESY. The promising results with the SIMCON 3.0. encouraged us to enter the design of SIMCON 3.1. possessing 10 measurement and control channels and some additional features to be reported in the next technical note. SIMCON 3.0. is a modular solution, while SIMCON 3.1. will be an integrated board of the all-in-one type. Two design approaches - modular and all-in-one, after branching off in this version of the Simcon, will be continued. (orig.)

Initial operation and performance of the PDX neutral-beam injection system

International Nuclear Information System (INIS)

Kugel, H.W.; Eubank, H.P.; Kozub, T.A.; Rossmassler, J.E.; Schilling, G.; van Halle, A.; Williams, M.D.

1982-01-01

In 1981, the joint ORNL/PPPL PDX neutral beam heating project succeeded in reliably injecting 7.2 MW of D 0 into the PDX plasma, at nearly perpendicular angles, and achieved ion temperatures up to 6.5 keV. The expeditious achievement of this result was due to the thorough conditioning and qualification of the PDX neutral beam ion sources at ORNL prior to delivery coupled with several field design changes and improvements in the injection system made at PPPL as a result of neutral beam operating experience with the PLT tokamak. It has been found that the operation of high power neutral beam injection systems in a tokamak-neutral beam environment requires procedures and performance different from those required for development operation on test stands. In this paper, we review the installatin of the PDX neutral beam injection system, and its operation and performance during the initial high power plasma heating experiments with the PDX tokamak

Test Results for the Automated Rendezvous and Capture System

Science.gov (United States)

Cruzen, Craig; Dabney, Richard; Lomas, James

1999-01-01

The Automated Rendezvous and Capture (AR&C) system was designed and tested at NASA's Marshall Space Flight Center (MSFC) to demonstrate technologies and mission strategies for automated rendezvous and docking of spacecraft in Earth orbit, The system incorporates some of the latest innovations in Global Positioning, System space navigation, laser sensor technologies and automated mission sequencing algorithms. The system's initial design and integration was completed in 1998 and has undergone testing at MSFC. This paper describes the major components of the AR&C system and presents results from the official system tests performed in MSFC's Flight Robotics Laboratory with digital simulations and hardware in the loop tests. The results show that the AR&C system can safely and reliably perform automated rendezvous and docking missions in the absence of system failures with 100 percent success. When system failures are included, the system uses its automated collision avoidance maneuver logic to recover in a safe manner. The primary objective of the AR&C project is to prove that by designing a safe and robust automated system, mission operations cost can be reduced by decreasing the personnel required for mission design, preflight planning and training required for crewed rendezvous and docking missions.

Initial results from NuSTAR observations of the Norma arm

DEFF Research Database (Denmark)

Bodaghee, Arash; Tomsick, John A.; Krivonos, Roman

2014-01-01

Results are presented for an initial survey of the Norma Arm gathered with the focusing hard X-ray telescope NuSTAR. The survey covers 0.2 deg2 of sky area in the 3-79 keV range with a minimum and maximum raw depth of 15 ks and 135 ks, respectively. Besides a bright black-hole X-ray binary...

Initial results of a positron tomograph for prostate imaging

Energy Technology Data Exchange (ETDEWEB)

Huber, J.S.; Choong, W.S.; Moses, W.W.; Qi, J.; Hu, J.; Wang,G.C.; Wilson, D.; Oh, S.; Huesman, R.H.; Derenzo, S.E.; Budinger, T.F.

2004-11-29

We present the status and initial images of a positrontomograph for prostate imaging that centers a patient between a pair ofexternal curved detector banks (ellipse: 45 cm minor, 70 cm major axis).The distance between detector banks adjusts to allow patient access andto position the detectors as closely as possible for maximum sensitivitywith patients of various sizes. Each bank is composed of two axial rowsof 20 CTI PET Systems HR+ block detectors for a total of 80 modules inthe camera. Compared to an ECAT HR PET system operating in 3D mode, ourcamera uses about one-quarter the number of detectors and hasapproximately the same sensitivity for a central point source, becauseour detectors are close to the patient. The individual detectors areangled in the plane to point towards the prostate to minimize resolutiondegradation in that region. The detectors are read out by modified CTIdata acquisition electronics. We have completed construction of thegantry and electronics, have developed detector calibration and dataacquisition software, and are taking coincidence data. We demonstratethat we can clearly visualize a "prostate" in a simple phantom.Reconstructed images of two phantoms are shown.

Preliminary results from initial in-pile debris bed experiments

International Nuclear Information System (INIS)

Rivard, J.B.

1977-01-01

An accident in a liquid metal fast breeder reactor (LMFBR) in which molten core material is suddenly quenched with subcooled liquid sodium could result in extensive fragmentation and dispersal of fuel as subcritical beds of frozen particulate debris within the reactor vessel. Since this debris will continue to generate power due to decay of retained fission products, containment of the debris is threatened if the generated heat is not removed. Therefore, the initial safety question is the capacity which debris beds may have for transfer of the decay heat to overlying liquid sodium by natural processes--i.e., without the aid of forced circulation of the coolant. Up to the present time, all experiments on debris bed behavior either have used substitute materials (e.g., sand and water) or have employed actual materials, but atypical heating methods. Increased confidence in the applicability of debris bed simulations is afforded if the heat is generated within the fuel component of the appropriate fast reactor materials. The initial series of in-pile tests reported on herein constitutes the first experiments in which the internal heating mode has been produced in particulate oxide fuel immersed in liquid sodium. Fission heating of the fully-enriched UO 2 in the experiment while it is contained within Sandia Laboratories Annular Core Pulse Reactor (ACPR), operating in its steady-state mode, approximates the decay heating of debris. Preliminary results are discussed

Using systems thinking in state health policymaking: an educational initiative.

Science.gov (United States)

Minyard, Karen J; Ferencik, Rachel; Ann Phillips, Mary; Soderquist, Chris

2014-06-01

In response to limited examples of opportunities for state policymakers to learn about and productively discuss the difficult, adaptive challenges of our health system, the Georgia Health Policy Center developed an educational initiative that applies systems thinking to health policymaking. We created the Legislative Health Policy Certificate Program - an in-depth, multi-session series for lawmakers and their staff - concentrating on building systems thinking competencies and health content knowledge by applying a range of systems thinking tools: behavior over time graphs, stock and flow maps, and a system dynamics-based learning lab (a simulatable model of childhood obesity). Legislators were taught to approach policy issues from the big picture, consider changing dynamics, and explore higher-leverage interventions to address Georgia's most intractable health challenges. Our aim was to determine how we could improve the policymaking process by providing a systems thinking-focused educational program for legislators. Over 3 years, the training program resulted in policymakers' who are able to think more broadly about difficult health issues. The program has yielded valuable insights into the design and delivery of policymaker education that could be applied to various disciplines outside the legislative process.

Initial Tests and Accuracy Assesment of a Compact Mobile Laser Scanning System

Science.gov (United States)

Julge, K.; Ellmann, A.; Vajakas, T.; Kolka, R.

2016-06-01

Mobile laser scanning (MLS) is a faster and cost-effective alternative to static laser scanning, even though there is a slight trade-off in accuracy. This contribution describes a compact mobile laser scanning system mounted on a vehicle. The technical parameters of the used system components, i.e. a small LIDAR sensor Velodyne VLP-16 and a dual antenna GNSS/INS system Advanced Navigation Spatial Dual, are reviewed, along with the integration of these components for spatial data acquisition. Calculation principles of 3D coordinates from the real-time data of all the involved sensors are discussed. The field tests were carried out in a controlled environment of a parking lot and at different velocities. Experiments were carried out to test the ability of the GNSS/INS system to cope with difficult conditions, e.g. sudden movements due to cornering or swerving. The accuracy of the resulting MLS point cloud is evaluated with respect to high-accuracy static terrestrial laser scanning data. Problems regarding combining LIDAR, GNSS and INS sensors are outlined, as well as the initial accuracy assessments. Initial tests revealed errors related to insufficient quality of inertial data and a need for the trajectory post-processing calculations. Although this study was carried out while the system was mounted on a car, there is potential for operating the system on an unmanned aerial vehicle, all-terrain vehicle or in a backpack mode due to its relatively compact size.

INITIAL TESTS AND ACCURACY ASSESMENT OF A COMPACT MOBILE LASER SCANNING SYSTEM

Directory of Open Access Journals (Sweden)

K. Julge

2016-06-01

Full Text Available Mobile laser scanning (MLS is a faster and cost-effective alternative to static laser scanning, even though there is a slight trade-off in accuracy. This contribution describes a compact mobile laser scanning system mounted on a vehicle. The technical parameters of the used system components, i.e. a small LIDAR sensor Velodyne VLP-16 and a dual antenna GNSS/INS system Advanced Navigation Spatial Dual, are reviewed, along with the integration of these components for spatial data acquisition. Calculation principles of 3D coordinates from the real-time data of all the involved sensors are discussed. The field tests were carried out in a controlled environment of a parking lot and at different velocities. Experiments were carried out to test the ability of the GNSS/INS system to cope with difficult conditions, e.g. sudden movements due to cornering or swerving. The accuracy of the resulting MLS point cloud is evaluated with respect to high-accuracy static terrestrial laser scanning data. Problems regarding combining LIDAR, GNSS and INS sensors are outlined, as well as the initial accuracy assessments. Initial tests revealed errors related to insufficient quality of inertial data and a need for the trajectory post-processing calculations. Although this study was carried out while the system was mounted on a car, there is potential for operating the system on an unmanned aerial vehicle, all-terrain vehicle or in a backpack mode due to its relatively compact size.

Gravitational Waves from Known Pulsars: Results from the Initial Detector Era

NARCIS (Netherlands)

Aasi, J.; et al., [Unknown; Hessels, J.W.T.

2014-01-01

We present the results of searches for gravitational waves from a large selection of pulsars using data from the most recent science runs (S6, VSR2 and VSR4) of the initial generation of interferometric gravitational wave detectors LIGO (Laser Interferometric Gravitational-wave Observatory) and

Initial Laboratory-Scale Melter Test Results for Combined Fission Product Waste

Energy Technology Data Exchange (ETDEWEB)

Riley, Brian J.; Crum, Jarrod V.; Buchmiller, William C.; Rieck, Bennett T.; Schweiger, Michael J.; Vienna, John D.

2009-10-01

This report describes the methods and results used to vitrify a baseline glass, CSLNTM-C-2.5 in support of the AFCI (Advanced Fuel Cycle Initiative) using a Quartz Crucible Scale Melter at the Pacific Northwest National Laboratory. Document number AFCI-WAST-PMO-MI-DV-2009-000184.

Implication of the dominant design in electronic initiation systems in the South African mining industry

CSIR Research Space (South Africa)

Smit, FC

1998-11-01

Full Text Available This article analyzes an emerging technological innovation, namely, electronic initiation systems for mining explosives in South Africa. The concept of electronic initiation is presenting itself as a challenge to traditional initiation systems...

Ontogeny of flight initiation in the fly Drosophila melanogaster: implications for the giant fibre system.

Science.gov (United States)

Hammond, Sarah; O'Shea, Michael

2007-11-01

There are two modes of flight initiation in Drosophila melanogaster-escape and voluntary. Although the circuitry underlying escape is accounted for by the Giant fibre (GF) system, the system underlying voluntary flight initiation is unknown. The GF system is functionally complete before the adult fly ecloses, but immature adults initially fail to react to a stimulus known to reliably evoke escape in mature adults. This suggests that escape in early adulthood, approximately 2-h post-eclosion, is not automatically triggered by the hard-wired GF system. Indeed, we reveal that escape behaviour displays a staged emergence during the first hour post-eclosion, suggesting that the GF system is subject to declining levels of suppression. Voluntary flight initiations are not observed at all during the period when the GF system is released from its suppression, nor indeed for some time after. We addressed the question whether voluntary flight initiation requires the GF system by observing take-off in Shak-B ( 2 ) mutant flies, in which the GF system is defunct. While the escape response is severely impaired in these mutants, they displayed normal voluntary flight initiation. Thus, the escape mechanism is subject to developmental modulation following eclosion and the GF system does not underlie voluntary flight.

Initial airworthiness determining the acceptability of new airborne systems

CERN Document Server

Gratton, Guy

2015-01-01

Designed as an introduction for both advanced students in aerospace engineering and existing aerospace engineers, this book covers both engineering theory and professional practice in establishing the airworthiness of new and modified aircraft. Initial Airworthiness includes information on: ·         how structural, handling, and systems evaluations are carried out; ·         the processes by which safety and fitness for purpose are determined; and ·         the use of both US and European unit systems Covering both civil and military practice and the current regulations and standards across Europe and North America, Initial Airworthiness will give the reader an understanding of how all the major aspects of an aircraft are certified, as well as providing a valuable source of reference for existing practitioners.

Initial Single-Shell Tank Retrieval System mission analysis report

International Nuclear Information System (INIS)

Hertzel, J.S.

1996-03-01

This document provides the mission analysis for the Initial Single-Shell Tank Retrieval System task, which supports the Single-Shell Tank Waste Retrieval Program in its commitment to remove waste from single-shell tanks for treatment and final closure

Initial results of the high resolution edge Thomson scattering upgrade at DIII-D.

Science.gov (United States)

Eldon, D; Bray, B D; Deterly, T M; Liu, C; Watkins, M; Groebner, R J; Leonard, A W; Osborne, T H; Snyder, P B; Boivin, R L; Tynan, G R

2012-10-01

Validation of models of pedestal structure is an important part of predicting pedestal height and performance in future tokamaks. The Thomson scattering diagnostic at DIII-D has been upgraded in support of validating these models. Spatial and temporal resolution, as well as signal to noise ratio, have all been specifically enhanced in the pedestal region. This region is now diagnosed by 20 view-chords with a spacing of 6 mm and a scattering length of just under 5 mm sampled at a nominal rate of 250 Hz. When mapped to the outboard midplane, this corresponds to ~3 mm spacing. These measurements are being used to test critical gradient models, in which pedestal gradients increase in time until a threshold is reached. This paper will describe the specifications of the upgrade and present initial results of the system.

Experimental test accelerator: description and results of initial experiments

International Nuclear Information System (INIS)

Fessenden, T.; Birx, D.; Briggs, R.

1980-01-01

The ETA is a high current (10,000 Amp) linear induction accelerator that produces short (30 ns) pulses of electrons at 5 MeV twice per second or in bursts of 5 pulses separated by as little as one millisecond. At this time the machine has operated at 65% of its design current and 90% of the design voltage. This report contains a description of the accelerator and its diagnostics; the results of the initial year of operation; a comparison of design codes with experiments on beam transport; and a discussion of some of the special problems and their status

African Health Systems Initiative (AHSI) | CRDI - Centre de ...

International Development Research Centre (IDRC) Digital Library (Canada)

The African Health Systems Initiative (AHSI) is a 10-year Canadian International Development Agency (CIDA)-supported program for strengthening African-led ... Le nouveau site Web et la nouvelle bibliothèque de ressources aideront à améliorer les systèmes d'information et d'enregistrement des faits d'état civil dans les ...

Initial ratio optimization for the ejector cooling system with thermal pumping effect (ECSTPE)

International Nuclear Information System (INIS)

He, Yijian; Sun, Yongjun; Zhang, Sheng; Lyu, Yuanli; Chen, Guangming

2016-01-01

Graphical abstract: The existing ejector cooling systems with thermal pumping effect (ECSTPEs) have severe problems of thermal energy and chilling load waste. The deviations of the initial ratio from its optimal value would lead to the deviations of the time length of cooling stage (TLCS), and finally, result in the performance deteriorations of the ECSTPEs. The results of the case study showed that, for an ECSTPE with R134a, a 10-second deviation from the optimal TLCS led to a decrease of 5.6% in the COP value and an increase of 23.7% in the chilling load, when the generation temperature, the condensing temperature and the evaporation temperature were 85 °C, 35 °C and 10 °C, respectively. Therefore, accurately controlling the TLCS corresponding to the optimal TLCS, which is derived on the basis of the optimal initial ratio, can effectively improve the performance of ECSPTEs. - Highlights: • ECSTPEs encounter challenges for a great waste of heat and chilling water. • Initial ratio optimization is proposed to improve the performance of ECSTPEs. • Based on the optimal initial ratio, the optimal TLCS control strategy is obtained. • With the optimal TLCS control, COP values of the ECSTPEs are effectively enhanced. • Accordingly, the chilling loads of the ECSTPEs are greatly reduced. - Abstract: An ejector cooling system with thermal pumping effect (ECSTPE) could operate without consumption of electric power, but it discards a great amount of thermal energy, which generally results in a lower COP value and a greater chilling load. An innovative concept for the optimal initial ratio is therefore proposed to develop the optimal time length of cooling stage (TLCS) control method. The optimal TLCS control method effectively improves the ECSTPE performance. First, in this context, it was theoretically proven that the optimal initial ratio could be used to reduce the energy loss and the chilling load. Second, it was formulated how to achieve the optimal initial

Implementation of a quality improvement initiative in Belgian diabetic foot clinics: feasibility and initial results.

Science.gov (United States)

Doggen, Kris; Van Acker, Kristien; Beele, Hilde; Dumont, Isabelle; Félix, Patricia; Lauwers, Patrick; Lavens, Astrid; Matricali, Giovanni A; Randon, Caren; Weber, Eric; Van Casteren, Viviane; Nobels, Frank

2014-07-01

This article aims to describe the implementation and initial results of an audit-feedback quality improvement initiative in Belgian diabetic foot clinics. Using self-developed software and questionnaires, diabetic foot clinics collected data in 2005, 2008 and 2011, covering characteristics, history and ulcer severity, management and outcome of the first 52 patients presenting with a Wagner grade ≥ 2 diabetic foot ulcer or acute neuropathic osteoarthropathy that year. Quality improvement was encouraged by meetings and by anonymous benchmarking of diabetic foot clinics. The first audit-feedback cycle was a pilot study. Subsequent audits, with a modified methodology, had increasing rates of participation and data completeness. Over 85% of diabetic foot clinics participated and 3372 unique patients were sampled between 2005 and 2011 (3312 with a diabetic foot ulcer and 111 with acute neuropathic osteoarthropathy). Median age was 70 years, median diabetes duration was 14 years and 64% were men. Of all diabetic foot ulcers, 51% were plantar and 29% were both ischaemic and deeply infected. Ulcer healing rate at 6 months significantly increased from 49% to 54% between 2008 and 2011. Management of diabetic foot ulcers varied between diabetic foot clinics: 88% of plantar mid-foot ulcers were off-loaded (P10-P90: 64-100%), and 42% of ischaemic limbs were revascularized (P10-P90: 22-69%) in 2011. A unique, nationwide quality improvement initiative was established among diabetic foot clinics, covering ulcer healing, lower limb amputation and many other aspects of diabetic foot care. Data completeness increased, thanks in part to questionnaire revision. Benchmarking remains challenging, given the many possible indicators and limited sample size. The optimized questionnaire allows future quality of care monitoring in diabetic foot clinics. Copyright © 2014 John Wiley & Sons, Ltd.

Initial Results of On-Line Earth System Science Course Offerings at the University of Nebraska-Omaha Through the Earth System Science Education Alliance

Science.gov (United States)

Shuster, R. D.; Grandgenett, N. F.; Schnase, W. L.; Hamersky, S.; Moshman, R.

2008-12-01

The University of Nebraska at Omaha has been offering on-line Earth System Science coursework to teachers in Nebraska since 2002. UNO was one of the initial members in the Earth Systems Science Education Alliance (ESSEA) and has offered three different ESSEA courses, with nearly 200 students having taken ESSEA courses at UNO for graduate credit. Our experiences in delivering this coursework have involved both teachers who have received a stipend to take the course and those who have paid their own tuition and fees and received graduate credit for the course. We will report on the online behavior of teachers from both populations and also discuss pros and cons of each approach. UNO has also experimented with different approaches in the support and management of the course, including using undergraduate majors as content experts. This improves access of teachers to content-related feedback and is a positive experience for the undergraduate major. Feedback surveys from earlier ESSEA offerings indicate a strongly positive perception of the courses by the teachers enrolled in the coursework. Project impact has been documented in teacher projects, quotes, and lessons associated with the coursework activities. We will also describe online course modules being developed within the UNO online course efforts, including one focusing on the global amphibian crisis.

Concerning initial and secondary character of radionuclide distribution in elementary landscape geochemical systems

Science.gov (United States)

Korobova, Elena; Romanov, Sergey

2017-04-01

Specificity of radionuclide distribution in elementary landscape geochemical systems (ELGS) treated as local system of geochemically linked elementary terrestrial units (in toposequence: watershed-slope-closing depression), belongs to one of the less investigated but practically significant problems of current geochemistry. First measurements after the Chernobyl accident showed a considerable variation of Cs-137 distribution in all examined ELGS (Shcheglov et al, 2001; Romanov, 1989; Korobova, Korovaykov, 1990; Linnik, 2008). The results may be interpreted in frames of two alternative hypotheses: 1) irregularity of the initial contamination; 2) secondary redistribution of the initially regular level of fallout. But herewith only a disproof of the first hypothesis automatically justifies the second one. Factors responsible for initial irregularity of surface contamination included: 1) the presence of the so-called "hot" particles in the initial fallout; 2) interception of radionuclides by forest canopy; 3) irregular aerial particles deposition; 4) uneven initial precipitation. Basing on monitoring Cs-137 spatial distribution that has been performed since 2005, we demonstrate that the observed spatial irregularity in distribution of Cs-137 in ELGS reflects a purely secondary distribution of initial reserves of radionuclides in fallout matter due to its migration with water in local geochemical systems. This statement has some significant consequences. 1. Mechanism of migration of matter in ELGS is complicated and could not be reduced solely to a primitive moving from watershed to closing depression. 2. The control of migration of "labeled atoms" (Cs-137) permits to understand common mechanism of migration of water in all systems on the level of ELGS. 3. Understanding formation of the structure of contamination zones in ELGS permits to use mathematical model to solve the inverse problem of restoration of the initially equable level of their contamination. Performed

Semilinear hyperbolic systems and equations with singular initial data

International Nuclear Information System (INIS)

Gramchev, T.

1991-07-01

We study the weak limits of solutions u ε (t, ·) for ε→0 to semilinear strictly hyperbolic systems and wave equations with initial data u ε (0, ·) approximating a distribution κ, 0 ε (t, ·) for ε→0 exists. 13 refs

Applying Diagnostics to Enhance Cable System Reliability (Cable Diagnostic Focused Initiative, Phase II)

Energy Technology Data Exchange (ETDEWEB)

Hartlein, Rick [Georgia Tech Research Corporation (GTRC), Atlanta, GA (United States). National Electric Energy Testing, Research and Applications Center (NEETRAC); Hampton, Nigel [Georgia Tech Research Corporation (GTRC), Atlanta, GA (United States). National Electric Energy Testing, Research and Applications Center (NEETRAC); Perkel, Josh [Georgia Tech Research Corporation (GTRC), Atlanta, GA (United States). National Electric Energy Testing, Research and Applications Center (NEETRAC); Hernandez, JC [Univ. de Los Andes, Merida (Venezuela); Elledge, Stacy [Georgia Tech Research Corporation (GTRC), Atlanta, GA (United States). National Electric Energy Testing, Research and Applications Center (NEETRAC); del Valle, Yamille [Georgia Tech Research Corporation (GTRC), Atlanta, GA (United States). National Electric Energy Testing, Research and Applications Center (NEETRAC); Grimaldo, Jose [Georgia Inst. of Technology, Atlanta, GA (United States). School of Electrical and Computer Engineering; Deku, Kodzo [Georgia Inst. of Technology, Atlanta, GA (United States). George W. Woodruff School of Mechanical Engineering

2016-02-01

The Cable Diagnostic Focused Initiative (CDFI) played a significant and powerful role in clarifying the concerns and understanding the benefits of performing diagnostic tests on underground power cable systems. This project focused on the medium and high voltage cable systems used in utility transmission and distribution (T&D) systems. While many of the analysis techniques and interpretations are applicable to diagnostics and cable systems outside of T&D, areas such as generating stations (nuclear, coal, wind, etc.) and other industrial environments were not the focus. Many large utilities in North America now deploy diagnostics or have changed their diagnostic testing approach as a result of this project. Previous to the CDFI, different diagnostic technology providers individually promoted their approach as the “the best” or “the only” means of detecting cable system defects.

Information data systems for a global change technology initiative architecture trade study

Science.gov (United States)

Murray, Nicholas D.

1991-01-01

The Global Change Technology Initiative (GCTI) was established to develop technology which will enable use of satellite systems of Earth observations on a global scale, enable use of the observations to predictively model Earth's changes, and provide scientists, government, business, and industry with quick access to the resulting information. At LaRC, a GCTI Architecture Trade Study was undertaken to develop and evaluate the architectural implications to meet the requirements of the global change studies and the eventual implementation of a global change system. The output of the trade study are recommended technologies for the GCTI. That portion of the study concerned with the information data system is documented. The information data system for an earth global change modeling system can be very extensive and beyond affordability in terms of today's costs. Therefore, an incremental approach to gaining a system is most likely. An options approach to levels of capability versus needed technologies was developed. The primary drivers of the requirements for the information data system evaluation were the needed science products, the science measurements, the spacecraft orbits, the instruments configurations, and the spacecraft configurations and their attendant architectures. The science products requirements were not studied here; however, some consideration of the product needs were included in the evaluation results. The information data system technology items were identified from the viewpoint of the desirable overall information system characteristics.

Initial results of local grid control using wind farms with grid support

Energy Technology Data Exchange (ETDEWEB)

Soerensen, Poul; Hansen, Anca D.; Iov, F.; Blaabjerg, F.

2005-09-01

This report describes initial results with simulation of local grid control using wind farms with grid support. The focus is on simulation of the behaviour of the wind farms when they are isolated from the main grid and establish a local grid together with a few other grid components. The isolated subsystems used in the work presented in this report do not intend to simulate a specific subsystem, but they are extremely simplified single bus bar systems using only a few more components than the wind farm. This approach has been applied to make it easier to understand the dynamics of the subsystem. The main observation is that the fast dynamics of the wind turbines seem to be able to contribute significantly to the grid control, which can be useful where the wind farm is isolated with a subsystem from the main grid with surplus of generation. Thus, the fast down regulation of the wind farm using automatic frequency control can keep the subsystem in operation and thereby improve the reliability of the grid. (LN)

An assessment of interactions between global health initiatives and country health systems.

Science.gov (United States)

Samb, Badara; Evans, Tim; Dybul, Mark; Atun, Rifat; Moatti, Jean-Paul; Nishtar, Sania; Wright, Anna; Celletti, Francesca; Hsu, Justine; Kim, Jim Yong; Brugha, Ruairi; Russell, Asia; Etienne, Carissa

2009-06-20

Since 2000, the emergence of several large disease-specific global health initiatives (GHIs) has changed the way in which international donors provide assistance for public health. Some critics have claimed that these initiatives burden health systems that are already fragile in countries with few resources, whereas others have asserted that weak health systems prevent progress in meeting disease-specific targets. So far, most of the evidence for this debate has been provided by speculation and anecdotes. We use a review and analysis of existing data, and 15 new studies that were submitted to WHO for the purpose of writing this Report to describe the complex nature of the interplay between country health systems and GHIs. We suggest that this Report provides the most detailed compilation of published and emerging evidence so far, and provides a basis for identification of the ways in which GHIs and health systems can interact to mutually reinforce their effects. On the basis of the findings, we make some general recommendations and identify a series of action points for international partners, governments, and other stakeholders that will help ensure that investments in GHIs and country health systems can fulfil their potential to produce comprehensive and lasting results in disease-specific work, and advance the general public health agenda. The target date for achievement of the health-related Millennium Development Goals is drawing close, and the economic downturn threatens to undermine the improvements in health outcomes that have been achieved in the past few years. If adjustments to the interactions between GHIs and country health systems will improve efficiency, equity, value for money, and outcomes in global public health, then these opportunities should not be missed.

Application of expert system technology to nondestructive waste assay - initial prototype model

Energy Technology Data Exchange (ETDEWEB)

Becker, G.K.; Determan, J.C. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

1997-11-01

Expert system technology has been identified as a technique useful for filling certain types of technology/capability gaps in existing waste nondestructive assay (NDA) applications. In particular, expert system techniques are being investigated with the intent of providing on-line evaluation of acquired data and/or directed acquisition of data in a manner that mimics the logic and decision making process a waste NDA expert would employ. The space from which information and data sources utilized in this process is much expanded with respect to the algorithmic approach typically utilized in waste NDA. Expert system technology provides a mechanism to manage and reason with this expanded information/data set. The material presented in this paper concerns initial studies and a resultant prototype expert system that incorporates pertinent information, and evaluation logic and decision processes, for the purpose of validating acquired waste NDA measurement assays. 6 refs., 6 figs.

Application of expert system technology to nondestructive waste assay - initial prototype model

International Nuclear Information System (INIS)

Becker, G.K.; Determan, J.C.

1997-01-01

Expert system technology has been identified as a technique useful for filling certain types of technology/capability gaps in existing waste nondestructive assay (NDA) applications. In particular, expert system techniques are being investigated with the intent of providing on-line evaluation of acquired data and/or directed acquisition of data in a manner that mimics the logic and decision making process a waste NDA expert would employ. The space from which information and data sources utilized in this process is much expanded with respect to the algorithmic approach typically utilized in waste NDA. Expert system technology provides a mechanism to manage and reason with this expanded information/data set. The material presented in this paper concerns initial studies and a resultant prototype expert system that incorporates pertinent information, and evaluation logic and decision processes, for the purpose of validating acquired waste NDA measurement assays. 6 refs., 6 figs

Hemorrhagic Tamponade as Initial Manifestation of Systemic Lupus with Subsequent Refractory and Progressive Lupus Myocarditis Resulting in Cardiomyopathy and Mitral Regurgitation

Directory of Open Access Journals (Sweden)

Nicole Marijanovich

2018-01-01

Full Text Available Systemic lupus erythematosus (SLE is a heterogeneous autoimmune disease with a wide range of clinical and serological manifestations. Cardiac disease among patients with SLE is common and can involve the pericardium, myocardium, valves, conduction system, and coronary arteries. We are reporting a case of SLE in a young woman that is unique is unique in that initial symptoms consisted of pericarditis and hemorrhagic tamponade which remained progressive and resistant to aggressive immunosuppressive treatment and led to severe cardiomyopathy (ejection fraction of 25% and severe (+4 mitral regurgitation. Her immunosuppressive treatment included hydroxychloroquine, high-dose steroids, intravenous immunoglobulins, azathioprine, and mycophenolate mofetil. Her disease progression was felt to be due to underlying uncontrolled SLE because the complement levels remained persistently low throughout the entire course and PET Myocardial Perfusion and Viability study showed stable persistent active inflammation. Eventually, she was treated with cyclophosphamide which led to improvement in ejection fraction to 55% with only mild mitral regurgitation.

Management Control System Support of Initiatives for Disruptive Students

Science.gov (United States)

Scott, Colin

2011-01-01

Purpose: The purpose of the paper is to investigate the management control system (MCS) support of school initiatives to develop the school climate and to re-engage disruptive students. Design/methodology/approach: The paper adopts an approach of critical action research interviews with management and document reviews informed by Habermasian…

Effect of intravenous administration of D-lysergic acid diethylamide on initiation of protein synthesis in a cell-free system derived from brain.

Science.gov (United States)

Cosgrove, J W; Brown, I R

1984-05-01

An initiating cell-free protein synthesis system derived from brain was utilized to demonstrate that the intravenous injection of D-lysergic acid diethylamide (LSD) to rabbits resulted in a lesion at the initiation stage of brain protein synthesis. Three inhibitors of initiation, edeine, poly(I), and aurintricarboxylic acid were used to demonstrate a reduction in initiation-dependent amino acid incorporation in the brain cell-free system. One hour after LSD injection, there was also a measurable decrease in the formation of 40S and 80S initiation complexes in vitro, using either [35S]methionine or [35S]Met-tRNAf. Analysis of the methionine pool size after LSD administration indicated there was no change in methionine levels. Analysis of the formation of initiation complexes in the brain cell-free protein synthesis system prepared 6 h after LSD administration indicated that there was a return to control levels at this time. The effects of LSD on steps in the initiation process are thus reversible.

Power system requirements and selection for the space exploration initiative

International Nuclear Information System (INIS)

Biringer, K.L.; Bartine, D.E.; Buden, D.; Foreman, J.; Harrison, S.

1991-01-01

The Space Exploration Initiative (SEI) seeks to reestablish a US program of manned and unmanned space exploration. The President has called for a program which includes a space station element, a manned habitation of the moon, and a human exploration of Mars. The NASA Synthesis Group has developed four significantly different architectures for the SEI program. One key element of a space exploration effort is the power required to support the missions. The Power Speciality Team of the Synthesis Group was tasked with assessing and evaluating the power requirements and candidate power technologies for such missions. Inputs to the effort came from existing NASA studies as well as other governments agency inputs such as those from DOD and DOE. In addition, there were industry and university briefings and results of solicitations from the AIAA and the general public as part of the NASA outreach effort. Because of the variety of power needs in the SEI program, there will be a need for multiple power system technologies including solar, nuclear and electrochemical. Due to the high rocket masses required to propel payloads to the moon and beyond to Mars, there is great emphasis placed on the need for high power density and high energy density systems. Power system technology development work is needed results will determine the ultimate technology selections. 23 refs., 10 figs

Moving science into state child and adolescent mental health systems: Illinois' evidence-informed practice initiative.

Science.gov (United States)

Starin, Amy C; Atkins, Marc S; Wehrmann, Kathryn C; Mehta, Tara; Hesson-McInnis, Matthew S; Marinez-Lora, A; Mehlinger, Renee

2014-01-01

In 2005, the Illinois State Mental Health Authority embarked on an initiative to close the gap between research and practice in the children's mental health system. A stakeholder advisory council developed a plan to advance evidence informed practice through policy and program initiatives. A multilevel approach was developed to achieve this objective, which included policy change, stakeholder education, and clinician training. This article focuses on the evidence-informed training process designed following review of implementation research. The training involved in-person didactic sessions and twice-monthly telephone supervision across 6 cohorts of community based clinicians, each receiving 12 months of training. Training content initially included cognitive behavioral therapy and behavioral parent training and was adapted over the years to a practice model based on common element concepts. Evaluation based on provider and parent report indicated children treated by training clinicians generally showed superior outcomes versus both a treatment-as-usual comparison group for Cohorts 1 to 4 and the statewide child population as a whole after 90 days of care for Cohorts 5 to 6. The results indicated primarily moderate to strong effects for the evidence-based training groups. Moving a large public statewide child mental health system toward more effective services is a complex and lengthy process. These results indicate training of community mental health providers in Illinois in evidence-informed practice was moderately successful in positively impacting child-level functional outcomes. These findings also influenced state policy in committing resources to continuing the initiative, even in difficult economic times.

Mars Science Laboratory relative humidity observations: Initial results.

Science.gov (United States)

Harri, A-M; Genzer, M; Kemppinen, O; Gomez-Elvira, J; Haberle, R; Polkko, J; Savijärvi, H; Rennó, N; Rodriguez-Manfredi, J A; Schmidt, W; Richardson, M; Siili, T; Paton, M; Torre-Juarez, M De La; Mäkinen, T; Newman, C; Rafkin, S; Mischna, M; Merikallio, S; Haukka, H; Martin-Torres, J; Komu, M; Zorzano, M-P; Peinado, V; Vazquez, L; Urqui, R

2014-09-01

The Mars Science Laboratory (MSL) made a successful landing at Gale crater early August 2012. MSL has an environmental instrument package called the Rover Environmental Monitoring Station (REMS) as a part of its scientific payload. REMS comprises instrumentation for the observation of atmospheric pressure, temperature of the air, ground temperature, wind speed and direction, relative humidity (REMS-H), and UV measurements. We concentrate on describing the REMS-H measurement performance and initial observations during the first 100 MSL sols as well as constraining the REMS-H results by comparing them with earlier observations and modeling results. The REMS-H device is based on polymeric capacitive humidity sensors developed by Vaisala Inc., and it makes use of transducer electronics section placed in the vicinity of the three humidity sensor heads. The humidity device is mounted on the REMS boom providing ventilation with the ambient atmosphere through a filter protecting the device from airborne dust. The final relative humidity results appear to be convincing and are aligned with earlier indirect observations of the total atmospheric precipitable water content. The water mixing ratio in the atmospheric surface layer appears to vary between 30 and 75 ppm. When assuming uniform mixing, the precipitable water content of the atmosphere is ranging from a few to six precipitable micrometers. Atmospheric water mixing ratio at Gale crater varies from 30 to 140 ppmMSL relative humidity observation provides good dataHighest detected relative humidity reading during first MSL 100 sols is RH75.

The Pluto system: Initial results from its exploration by New Horizons.

Science.gov (United States)

Stern, S A; Bagenal, F; Ennico, K; Gladstone, G R; Grundy, W M; McKinnon, W B; Moore, J M; Olkin, C B; Spencer, J R; Weaver, H A; Young, L A; Andert, T; Andrews, J; Banks, M; Bauer, B; Bauman, J; Barnouin, O S; Bedini, P; Beisser, K; Beyer, R A; Bhaskaran, S; Binzel, R P; Birath, E; Bird, M; Bogan, D J; Bowman, A; Bray, V J; Brozovic, M; Bryan, C; Buckley, M R; Buie, M W; Buratti, B J; Bushman, S S; Calloway, A; Carcich, B; Cheng, A F; Conard, S; Conrad, C A; Cook, J C; Cruikshank, D P; Custodio, O S; Dalle Ore, C M; Deboy, C; Dischner, Z J B; Dumont, P; Earle, A M; Elliott, H A; Ercol, J; Ernst, C M; Finley, T; Flanigan, S H; Fountain, G; Freeze, M J; Greathouse, T; Green, J L; Guo, Y; Hahn, M; Hamilton, D P; Hamilton, S A; Hanley, J; Harch, A; Hart, H M; Hersman, C B; Hill, A; Hill, M E; Hinson, D P; Holdridge, M E; Horanyi, M; Howard, A D; Howett, C J A; Jackman, C; Jacobson, R A; Jennings, D E; Kammer, J A; Kang, H K; Kaufmann, D E; Kollmann, P; Krimigis, S M; Kusnierkiewicz, D; Lauer, T R; Lee, J E; Lindstrom, K L; Linscott, I R; Lisse, C M; Lunsford, A W; Mallder, V A; Martin, N; McComas, D J; McNutt, R L; Mehoke, D; Mehoke, T; Melin, E D; Mutchler, M; Nelson, D; Nimmo, F; Nunez, J I; Ocampo, A; Owen, W M; Paetzold, M; Page, B; Parker, A H; Parker, J W; Pelletier, F; Peterson, J; Pinkine, N; Piquette, M; Porter, S B; Protopapa, S; Redfern, J; Reitsema, H J; Reuter, D C; Roberts, J H; Robbins, S J; Rogers, G; Rose, D; Runyon, K; Retherford, K D; Ryschkewitsch, M G; Schenk, P; Schindhelm, E; Sepan, B; Showalter, M R; Singer, K N; Soluri, M; Stanbridge, D; Steffl, A J; Strobel, D F; Stryk, T; Summers, M E; Szalay, J R; Tapley, M; Taylor, A; Taylor, H; Throop, H B; Tsang, C C C; Tyler, G L; Umurhan, O M; Verbiscer, A J; Versteeg, M H; Vincent, M; Webbert, R; Weidner, S; Weigle, G E; White, O L; Whittenburg, K; Williams, B G; Williams, K; Williams, S; Woods, W W; Zangari, A M; Zirnstein, E

2015-10-16

The Pluto system was recently explored by NASA's New Horizons spacecraft, making closest approach on 14 July 2015. Pluto's surface displays diverse landforms, terrain ages, albedos, colors, and composition gradients. Evidence is found for a water-ice crust, geologically young surface units, surface ice convection, wind streaks, volatile transport, and glacial flow. Pluto's atmosphere is highly extended, with trace hydrocarbons, a global haze layer, and a surface pressure near 10 microbars. Pluto's diverse surface geology and long-term activity raise fundamental questions about how small planets remain active many billions of years after formation. Pluto's large moon Charon displays tectonics and evidence for a heterogeneous crustal composition; its north pole displays puzzling dark terrain. Small satellites Hydra and Nix have higher albedos than expected. Copyright © 2015, American Association for the Advancement of Science.

Research on Initiation Sensitivity of Solid Explosive and Planer Initiation System

OpenAIRE

N Matsuo; M Otuka; H Hamasima; K Hokamoto; S Itoh

2016-01-01

Firstly, recently, there are a lot of techniques being demanded for complex process, various explosive initiation method and highly accurate control of detonation are needed. In this research, the metal foil explosion using high current is focused attention on the method to obtain linear or planate initiation easily, and the main evaluation of metal foil explosion to initiate explosive was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated ...

4 MW upgrade to DIII-D FWCD system: System commissioning and initial operation

International Nuclear Information System (INIS)

Cary, W.P.; Callis, R.W.; deGrassie, J.S.; Harris, T.E.; O'Neill, R.C.; Pinsker, R.I.; Baity, F.W.; Barber, G.C.; Ferguson, S.W.

1995-01-01

The initial installation of the 4 MW fast wave current drive (FWCD) upgrade started in 1992 with the purchase of two ABB/Thomcast AG rf power amplifiers. These amplifiers cover the frequency range 30 MHz to 120 MHz. A maximum output power of over 2 MW between 30 MHz and 80 MHz and 1 MW at 120 MHz were the specification requirements. The system as installed is comprised of the two mentioned rf amplifiers, coaxial transmission and matching components, rf phase and amplitude monitoring, and a SUN SparcStation 10 control system. Due to various reasons almost every major component in the system required redesign and engineering in order to meet the system requirements. The failures, probable cause and the final redesigns will be discussed as well as some thoughts on how better to specify system requirements for future systems

4 MW upgrade to DIII-D FWCD system: System commissioning and initial operation

International Nuclear Information System (INIS)

Cary, W.P.; Callis, R.W.; Grassie, J.S. de; Harris, T.E.; O'Neill, R.C.; Pinsker, R.I.; Baity, F.W.; Barber, G.C.; Ferguson, S.W.

1995-10-01

The initial installation of the 4 MW fast wave current drive (FWCD) upgrade started in 1992 with the purchase of two ABB/Thomcast AG rf power amplifiers. These amplifiers cover the frequency range 30 MHz to 120 MHz. A maximum output power of over 2 MW between 30 MHz and 80 MHz and 1 MW at 120 MHz were the specification requirements. The system as installed is comprised of the two mentioned rf amplifiers, coaxial transmission and matching components, rf phase and amplitude monitoring, and a SUN SparcStation 10 control system. Due to various reasons almost every major component in the system required redesign and engineering in order to meet the system requirements. The failures, probable cause and the final redesigns will be discussed as well as some thoughts on how better to specify system requirements for future systems

CRBRP design and test results for fuel handling systems, plugs, and seals

International Nuclear Information System (INIS)

Berg, G.E.

1977-01-01

The fuel handling system and reactor rotating plugs for the Clinch River Breeder Reactor Plant (CRBRP) are based primarily on existing technology and, in many respects, follow the concept developed for the Fast Flux Test Facility (FFTF). The equipment and the development programs initiated to verify its performance are described. Test results obtained from the development program, and the extent to which these results verified original design selections, or suggested potential improvements, are discussed

Fractional Differential Equations in Terms of Comparison Results and Lyapunov Stability with Initial Time Difference

Directory of Open Access Journals (Sweden)

Coşkun Yakar

2010-01-01

Full Text Available The qualitative behavior of a perturbed fractional-order differential equation with Caputo's derivative that differs in initial position and initial time with respect to the unperturbed fractional-order differential equation with Caputo's derivative has been investigated. We compare the classical notion of stability to the notion of initial time difference stability for fractional-order differential equations in Caputo's sense. We present a comparison result which again gives the null solution a central role in the comparison fractional-order differential equation when establishing initial time difference stability of the perturbed fractional-order differential equation with respect to the unperturbed fractional-order differential equation.

Research Initiatives and Preliminary Results In Automation Design In Airspace Management in Free Flight

Science.gov (United States)

Corker, Kevin; Lebacqz, J. Victor (Technical Monitor)

1997-01-01

The NASA and the FAA have entered into a joint venture to explore, define, design and implement a new airspace management operating concept. The fundamental premise of that concept is that technologies and procedures need to be developed for flight deck and ground operations to improve the efficiency, the predictability, the flexibility and the safety of airspace management and operations. To that end NASA Ames has undertaken an initial development and exploration of "key concepts" in the free flight airspace management technology development. Human Factors issues in automation aiding design, coupled aiding systems between air and ground, communication protocols in distributed decision making, and analytic techniques for definition of concepts of airspace density and operator cognitive load have been undertaken. This paper reports the progress of these efforts, which are not intended to definitively solve the many evolving issues of design for future ATM systems, but to provide preliminary results to chart the parameters of performance and the topology of the analytic effort required. The preliminary research in provision of cockpit display of traffic information, dynamic density definition, distributed decision making, situation awareness models and human performance models is discussed as they focus on the theme of "design requirements".

Sustainability Initiatives Driving Supply Chain: Climate Governance on Beef Production System

Directory of Open Access Journals (Sweden)

Ieda Kanashiro Makiya

2015-04-01

Full Text Available Two conceptual frameworks have been analytically dominant in researching innovation dynamics in sustainability transition processes, namely technological innovation systems (TIS and the multi-level perspective (MLP. The innovation systems has been principally concerned with emerging new technologies and their potential contribution to future sustainability, whereas MLP has been more strongly oriented toward reconstructing historical processes of sectorial change. In this perspective, this study aims to analyses how global climate change and environmental pressures impact on the governance of supply chain and the ripple effects on natural resource-intensive economies. Some initiatives are taken to address regulatory issues and reconcile decision-making tools on quality assurance program on value chains. This includes a multi-level perspective (MLP as Carbon Disclosure Project (CDP and technological innovation systems (TIS as Geographic Information System (GIS used as a tracking system for monitoring sustainable practices. The paper discuss the drivers of sustainable beef production system, mainly in Legal Amazon, Brazil, and requirements from a largest retailer aligned to Brazilian public policies. This study presents three distinct strategies: (1 government and public policies to control deforestation related to beef cattle production system, (2 economic approach related to transnational supermarket chain and sustainability initiatives, (3 collective action for decision-making by multiple drivers

Research on Initiation Sensitivity of Solid Explosive and Planer Initiation System

Directory of Open Access Journals (Sweden)

N Matsuo

2016-09-01

Full Text Available Firstly, recently, there are a lot of techniques being demanded for complex process, various explosive initiation method and highly accurate control of detonation are needed. In this research, the metal foil explosion using high current is focused attention on the method to obtain linear or planate initiation easily, and the main evaluation of metal foil explosion to initiate explosive was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metal foil explosion. Secondly, in high energy explosive processing, there are several applications, such as shock compaction, explosive welding, food processing and explosive forming. In these explosive applications, a high sensitive explosive has been mainly used. The high sensitive explosive is so dangerous, since it can lead to explosion suddenly. So, for developing explosives, the safety is the most important thing as well as low manufacturing cost and explosive characteristics. In this work, we have focused on the initiation sensitivity of a solid explosive and performed numerical analysis of sympathetic detonation. The numerical analysis is calculated by LS-DYNA 3D (commercial code. To understand the initiation reaction of an explosive, Lee-Tarver equation was used and impact detonation process was analyzed by ALE code. Configuration of simulation model is a quarter of circular cylinder. The donor type of explosive (SEP was used as initiation explosive. When the donor explosive is exploded, a shock wave is generated and it propagates into PMMA, air and metallic layers in order. During passing through the layers, the shock wave is attenuated and finally, it has influence on the acceptor explosive, Comp. B. Here, we evaluate the initiation of acceptor explosive and discuss about detonation pressure, reactive rate of acceptor explosive and attenuation of impact pressure.

Virtual enterprise architecture and methodology - Initial results from the Globeman21 project

DEFF Research Database (Denmark)

Vesterager, Johan; Larsen, Lars Bjørn; Gobbi, Chiara

1999-01-01

This paper will focus on presenting the initial results from the IMS project Globeman21 regarding generic models for Extended Enterprise Management (EEM). In particular the paper outlines a proposed architecture for the creation of virtual enterprises, industrial requirements regarding the generic...... models, terminology for describing extended enterprises, and initial considerations regarding a methodology for EEM. Globeman21 see the extended enterprise as a concept covering the totality of different concepts dealing with the expansion or extension of enterprise activities. One way of realising...... the concept of extended enterprise is through the creation of virtual enterprise, based on a more or less formalised network. This approach is the basis for the development of the generic EEM model within Globeman21....

Integrated thermal treatment system sudy: Phase 2, Results

Energy Technology Data Exchange (ETDEWEB)

Feizollahi, F.; Quapp, W.J.

1995-08-01

This report presents the second phase of a study on thermal treatment technologies. The study consists of a systematic assessment of nineteen thermal treatment alternatives for the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the MLLW. The alternatives considered in Phase 2 were innovative thermal treatments with nine types of primary processing units. Other variations in the study examined the effect of combustion gas, air pollution control system design, and stabilization technology for the treatment residues. The Phase 1 study, the results of which have been published as an interim report, examined ten initial thermal treatment alternatives. The Phase 2 systems were evaluated in essentially the same manner as the Phase 2 systems. The assumptions and methods were the same as for the Phase 1 study. The quantities, and physical and chemical compositions, of the input waste used in he Phase 2 systems differ from those in the Phase 1 systems, which were based on a preliminary waste input database developed at the onset of the Integrated Thermal Treatment System study. The inventory database used in the Phase 2 study incorporates the latest US Department of Energy information. All systems, both primary treatment systems and subsystem inputs, have now been evaluated using the same waste input (2,927 lb/hr).

Integrated thermal treatment system sudy: Phase 2, Results

International Nuclear Information System (INIS)

Feizollahi, F.; Quapp, W.J.

1995-08-01

This report presents the second phase of a study on thermal treatment technologies. The study consists of a systematic assessment of nineteen thermal treatment alternatives for the contact-handled mixed low-level waste (MLLW) currently stored in the US Department of Energy complex. The treatment alternatives consist of widely varying technologies for safely destroying the hazardous organic components, reducing the volume, and preparing for final disposal of the MLLW. The alternatives considered in Phase 2 were innovative thermal treatments with nine types of primary processing units. Other variations in the study examined the effect of combustion gas, air pollution control system design, and stabilization technology for the treatment residues. The Phase 1 study, the results of which have been published as an interim report, examined ten initial thermal treatment alternatives. The Phase 2 systems were evaluated in essentially the same manner as the Phase 2 systems. The assumptions and methods were the same as for the Phase 1 study. The quantities, and physical and chemical compositions, of the input waste used in he Phase 2 systems differ from those in the Phase 1 systems, which were based on a preliminary waste input database developed at the onset of the Integrated Thermal Treatment System study. The inventory database used in the Phase 2 study incorporates the latest US Department of Energy information. All systems, both primary treatment systems and subsystem inputs, have now been evaluated using the same waste input (2,927 lb/hr)

Self-initiated actions result in suppressed auditory but amplified visual evoked components in healthy participants.

Science.gov (United States)

Mifsud, Nathan G; Oestreich, Lena K L; Jack, Bradley N; Ford, Judith M; Roach, Brian J; Mathalon, Daniel H; Whitford, Thomas J

2016-05-01

Self-suppression refers to the phenomenon that sensations initiated by our own movements are typically less salient, and elicit an attenuated neural response, compared to sensations resulting from changes in the external world. Evidence for self-suppression is provided by previous ERP studies in the auditory modality, which have found that healthy participants typically exhibit a reduced auditory N1 component when auditory stimuli are self-initiated as opposed to externally initiated. However, the literature investigating self-suppression in the visual modality is sparse, with mixed findings and experimental protocols. An EEG study was conducted to expand our understanding of self-suppression across different sensory modalities. Healthy participants experienced either an auditory (tone) or visual (pattern-reversal) stimulus following a willed button press (self-initiated), a random interval (externally initiated, unpredictable onset), or a visual countdown (externally initiated, predictable onset-to match the intrinsic predictability of self-initiated stimuli), while EEG was continuously recorded. Reduced N1 amplitudes for self- versus externally initiated tones indicated that self-suppression occurred in the auditory domain. In contrast, the visual N145 component was amplified for self- versus externally initiated pattern reversals. Externally initiated conditions did not differ as a function of their predictability. These findings highlight a difference in sensory processing of self-initiated stimuli across modalities, and may have implications for clinical disorders that are ostensibly associated with abnormal self-suppression. © 2016 Society for Psychophysiological Research.

Adherence of private health system hospitals to dissemination of outcomes according to the Global Reporting Initiative (GRI) model

OpenAIRE

Machado Junior, Celso; César, Robson Danúbio da Silva; Souza, Maria Tereza Saraiva de

2017-01-01

ABSTRACT Objective To verify if there is an analogy between the indicators of the Global Reporting Initiative adopted by hospitals in the private healthcare system. Methods Documentary research supported by reports that are electronically available on the website of the companies surveyed. Results The organizations surveyed had a significant adherence of their economic, social and environmental indicators of the model proposed by the Global Reporting Initiative, showing an analogous fie...

Adherence of private health system hospitals to dissemination of outcomes according to the Global Reporting Initiative (GRI) model

OpenAIRE

Machado, Celso; César, Robson Danúbio da Silva; de Souza, Maria Tereza Saraiva

2017-01-01

ABSTRACT Objective To verify if there is an analogy between the indicators of the Global Reporting Initiative adopted by hospitals in the private healthcare system. Methods Documentary research supported by reports that are electronically available on the website of the companies surveyed. Results The organizations surveyed had a significant adherence of their economic, social and environmental indicators of the model proposed by the Global Reporting Initiative, showing an analogous field of ...

Bioregenerative Life Support System Research as part of the DLR EDEN Initiative

Science.gov (United States)

Bamsey, Matthew; Schubert, Daniel; Zabel, Paul; Poulet, Lucie; Zeidler, Conrad

In 2011, the DLR Institute of Space Systems launched a research initiative called EDEN - Evolution and Design of Environmentally-closed Nutrition-Sources. The research initiative focuses on bioregenerative life support systems, especially greenhouse modules, and technologies for future crewed vehicles. The EDEN initiative comprises several projects with respect to space research, ground testing and spin-offs. In 2014, EDEN’s new laboratory officially opened. This new biological cleanroom laboratory comprises several plant growth chambers incorporating a number of novel controlled environment agriculture technologies. This laboratory will be the nucleus for a variety of plant cultivation experiments within closed environments. The utilized technologies are being advanced using the pull of space technology and include such items as stacked growth systems, PAR-specific LEDs, intracanopy lighting, aeroponic nutrient delivery systems and ion-selective nutrient sensors. The driver of maximizing biomass output per unit volume and energy has much application in future bioregenerative life support systems but can also provide benefit terrestrially. The EDEN laboratory also includes several specially constructed chambers for advancing models addressing the interaction between bioregenerative and physical-chemical life support systems. The EDEN team is presently developing designs for containerized greenhouse modules. One module is planned for deployment to the German Antarctic Station, Neumayer III. The shipping container based system will provide supplementation to the overwintering crew’s diet, provide psychological benefit while at the same time advancing the technology and operational readiness of harsh environment plant production systems. In addition to hardware development, the EDEN team has participated in several early phase designs such as for the ESA Greenhouse Module for Space System and for large-scale vertical farming. These studies often utilize the

Experimental Results of Integrated Refrigeration and Storage System Testing

Science.gov (United States)

Notardonato, W. U.; Johnson, W. L.; Jumper, K.

2009-01-01

Launch operations engineers at the Kennedy Space Center have identified an Integrated Refrigeration and Storage system as a promising technology to reduce launch costs and enable advanced cryogenic operations. This system uses a close cycle Brayton refrigerator to remove energy from the stored cryogenic propellant. This allows for the potential of a zero loss storage and transfer system, as well and control of the state of the propellant through densification or re-liquefaction. However, the behavior of the fluid in this type of system is different than typical cryogenic behavior, and there will be a learning curve associated with its use. A 400 liter research cryostat has been designed, fabricated and delivered to KSC to test the thermo fluid behavior of liquid oxygen as energy is removed from the cryogen by a simulated DC cycle cryocooler. Results of the initial testing phase focusing on heat exchanger characterization and zero loss storage operations using liquid oxygen are presented in this paper. Future plans for testing of oxygen densification tests and oxygen liquefaction tests will also be discussed. KEYWORDS: Liquid Oxygen, Refrigeration, Storage

Initial and regime situations in the decay of unstable quantum systems

International Nuclear Information System (INIS)

Rimini, A.; Zambotti, G.

1980-01-01

Two different definitions of survival probability in the decay of an unstable quantum system are considered and the equations for them are deduced from the equation for the density operator. The regime situation for the ensemble of unstable systems is studied and the density operator in such a situation is derived. The possible definitions of lifetime are discussed. If the adopted definition makes reference to all time including the early ones, then it is compulsory to specify exactly the state at the initial time. The correct equations for the survival probabilities in such conditions are derived. Two typical examples of decay experiments are considered and the influence of the initial preparation on the mean life is discussed. Numerical examples are given. (author)

Radiofrequency ablation of chondroblastoma using a multi-tined expandable electrode system: initial results

International Nuclear Information System (INIS)

Tins, Bernhard; Cassar-Pullicino, Victor; McCall, Iain; Cool, Paul; Williams, David; Mangham, David

2006-01-01

The standard treatment for chondroblastoma is surgery, which can be difficult and disabling due to its apo- or epiphyseal location. Radiofrequency (RF) ablation potentially offers a minimally invasive alternative. The often large size of chondroblastomas can make treatment with plain electrode systems difficult or impossible. This article describes the preliminary experience of RF treatment of chondroblastomas with a multi-tined expandable RF electrode system. Four cases of CT guided RF treatment are described. The tumour was successfully treated in all cases. In two cases, complications occurred; infraction of a subarticular chondroblastoma in one case and cartilage and bone damage in the unaffected compartment of a knee joint in the other. Radiofrequency treatment near a joint surface threatens the integrity of cartilage and therefore long-term joint function. In weight-bearing areas, the lack of bone replacement in successfully treated lesions contributes to the risk of mechanical failure. Multi-tined expandable electrode systems allow the treatment of large chondroblastomas. In weight-bearing joints and lesions near to the articular cartilage, there is a risk of cartilage damage and mechanical weakening of the bone. In lesions without these caveats, RF ablation appears promising. The potential risks and benefits need to be evaluated for each case individually. (orig.)

Radiofrequency ablation of chondroblastoma using a multi-tined expandable electrode system: initial results

Energy Technology Data Exchange (ETDEWEB)

Tins, Bernhard; Cassar-Pullicino, Victor; McCall, Iain [RJAH Orthopaedic and District Hospital, Department of Radiology, Oswestry (United Kingdom); Cool, Paul [RJAH Orthopaedic and District Hospital, Musculoskeletal Tumour Unit, Oswestry (United Kingdom); Williams, David [Hereford Hospital, Department of Orthopaedics, Hereford (United Kingdom); Mangham, David [RJAH Orthopaedic and District Hospital, Department of Pathology, Oswestry (United Kingdom)

2006-04-15

The standard treatment for chondroblastoma is surgery, which can be difficult and disabling due to its apo- or epiphyseal location. Radiofrequency (RF) ablation potentially offers a minimally invasive alternative. The often large size of chondroblastomas can make treatment with plain electrode systems difficult or impossible. This article describes the preliminary experience of RF treatment of chondroblastomas with a multi-tined expandable RF electrode system. Four cases of CT guided RF treatment are described. The tumour was successfully treated in all cases. In two cases, complications occurred; infraction of a subarticular chondroblastoma in one case and cartilage and bone damage in the unaffected compartment of a knee joint in the other. Radiofrequency treatment near a joint surface threatens the integrity of cartilage and therefore long-term joint function. In weight-bearing areas, the lack of bone replacement in successfully treated lesions contributes to the risk of mechanical failure. Multi-tined expandable electrode systems allow the treatment of large chondroblastomas. In weight-bearing joints and lesions near to the articular cartilage, there is a risk of cartilage damage and mechanical weakening of the bone. In lesions without these caveats, RF ablation appears promising. The potential risks and benefits need to be evaluated for each case individually. (orig.)

Arase: mission overview and initial results

Science.gov (United States)

Miyoshi, Y.; Shinohara, I.; Takashima, T.; Asamura, K.; Wang, S. Y.; Kazama, Y.; Kasahara, S.; Yokota, S.; Mitani, T.; Higashio, N.; Kasahara, Y.; Kasaba, Y.; Yagitani, S.; Matsuoka, A.; Kojima, H.; Kazuo, S.; Seki, K.; Hori, T.; Shoji, M.; Teramoto, M.; Chang, T. F.; Kurita, S.; Matsuda, S.; Keika, K.; Miyashita, Y.; Hosokawa, K.; Ogawa, Y.; Kadokura, A.; Kataoka, R.; Ono, T.

2017-12-01

Geospace Exploation Project; ERG addresses what mechanisms cause acceleration, transportation and loss of MeV electrons of the radiation belts and evolutions of space storms. Cross-energy and cross-regional couplings are key concepts for the project. In order to address questions, the project has been organized by three research teams; satellite observations, ground-based observations, and modeling/data-analysis studies, and interdisciplinary research are realized for comprehensive understanding of geospace. The Arase (ERG) satellite had been developed and 9 science instruments are developed and provided from JAXA, universities and instituted in Japan and Taiwan. The Arase satellite was successfully launched on December 20, 2016. After the initial operation including maneuvers, Arase has started normal observations since March, 2017. Until now, Arase has observed several geomagnetic storms driven by coronal hole streams and CMEs, and several interesting features are observed associated with geomagnetic disturbances. The six particle instruments; LEP-e/LEP-i/MEP-e/MEP-i/HEP/XEP have shown large enhancement as well as loss of wide energy electrons and ions and variations as well as changes of pitch angle and energy spectrum. The two field/wave instruments: PWE and MGF observed several kinds of plasma waves such as chorus, hiss, EMIC as well as large scale electric and magnetic field variations. And newly developed S-WPIA has been operated to identify micro-process of wave-particle interactions. Since conjugate observations between Arase and ground-based observations are essential for comprehensive understanding of geospace, we organized several campaign observations that include both satellite and ground-based observations. The project has collaborated with the international projects, EISCAT, SuperDARN and other ground-based observations, and various data are obtained from such international collaborations. Moreover, multi-point satellite observations by

The Far Ultraviolet M-dwarf Evolution Survey (FUMES): Overview and Initial Results

Science.gov (United States)

Pineda, J. Sebastian; France, Kevin; Youngblood, Allison

2018-01-01

M-dwarf stars are prime targets for exoplanet searches because of their close proximity and favorable properties for both planet detection and characterization, with current searches around these targets having already discovered several Earth-sized planets within their star’s habitable zones. However, the atmospheric characterization and potential habitability of these exoplanetary systems depends critically on the high-energy stellar radiation environment from X-rays to NUV. Strong radiation at these energies can lead to atmospheric mass loss and is a strong driver of photochemistry in planetary atmospheres. Recently, the MUSCLES Treasury Survey provided the first comprehensive assessment of the high-energy radiation field around old, planet hosting M-dwarfs. However, the habitability and potential for such exoplanetary atmospheres to develop life also depends on the evolution of the atmosphere and hence the evolution of the incident radiation field. The strong high-energy spectrum of young M-dwarfs can have devastating consequences for the potential habitability of a given system. We, thus, introduce the Far Ultraviolet M-dwarf Evolution Survey (FUMES), a new HST-STIS observing campaign targeting 10 early-mid M dwarfs with known rotation periods, including 6 targets with known ages, to assess the evolution of the FUV radiation, including Lyα, of M-dwarf stars with stellar rotation period. We present the initial results of our survey characterizing the FUV emission features of our targets and the implications of our measurements for the evolution of the entire high-energy radiation environment around M-dwarfs from youth to old age.

Overview of results and perspectives from the Shoreham major common-cause initiating events study

International Nuclear Information System (INIS)

Joksimovich, V.; Orvis, D.D.; Paccione, R.J.

1986-01-01

This study represents the continuation of a large effort by LILCO to fully understand the potential hazards posed by future operation of the Shoreham Nuclear Power Stations (SNPS). The Shoreham Probabilistic Risk Assessment, a level 3 PRA without external events, provided a characterization of the accident sequences that could leave the core in a condition in which it would be vulnerable to severe damage if further mitigating actions were not taken. It estimated the frequency and magnitude of the potential radioactivity releases associated with such sequences. The study was limited to accident sequences initiated by so called internal events to the plant including a loss of offsite power. It also characterized the public risk associated with those accident sequences. The ''Major Common-Cause Initiating Events Study'' (MCCI) for the Shoreham plant was performed to obtain insights into the plant's susceptibility to, and inherent defenses against, certain MCCIs. Major common-cause initiating events are occurrences which have the potential to initiate a plant transient or LOCA and, also, damage one or more plant systems needed to mitigate the effects of a transient or LOCA. The scope of the MCCI study included detailed analyses of seismic events and fires through the severe core damage and bounding analyses of aircraft crashes, windstorms, turbine missiles and release of hazardous materials near the plant

Applications of research results from NPAR service water system studies

International Nuclear Information System (INIS)

Jarrell, D.B.; Stratton, R.C.

1991-01-01

Under the Nuclear Plant Aging Research (NPAR) program, the Nuclear Regulatory Commission (NRC) has invested considerable resources in understanding the mechanisms, mitigating the damage, and managing the results of nuclear power plant aging degradation. Many direct benefits have resulted from this program in terms of improved plant safety through upgraded regulatory guidance. The 'Service Water System (SWS) Aging Degradation Assessment' (NUREG/CR-5379), produced by the Pacific Northwest Laboratory (PNL), contributed to this program. Two other benefits have resulted from the NPAR SWS task: (1) a contribution to the content of Generic Letter 89-13 (nuclear plant SWS performance requirements) and (2) the development of a systematic and complete root-cause analysis (RCA) methodology for use in the solution of SWS as well as other system component failures. Less recognized, but also of significance, are the spin-off initiatives from the NRC's NPAR program investigations. One such spin-off resulting specifically from the NRC-sponsored SWS research is the continuing development of the RCA methodology to facilitate the computerized integration of the following: (1) component condition monitoring; (2) fault diagnostics; and (3) failure root cause analysis. The Decision Support system for Operations and Maintenance project being developed at PNL is implementing the NPAR-developed RCA methodology utilizing an artificial intelligence approach

In-motion initial alignment and positioning with INS/CNS/ODO integrated navigation system for lunar rovers

Science.gov (United States)

Lu, Jiazhen; Lei, Chaohua; Yang, Yanqiang; Liu, Ming

2017-06-01

Many countries have been paying great attention to space exploration, especially about the Moon and the Mars. Autonomous and high-accuracy navigation systems are needed for probers and rovers to accomplish missions. Inertial navigation system (INS)/celestial navigation system (CNS) based navigation system has been used widely on the lunar rovers. Initialization is a particularly important step for navigation. This paper presents an in-motion alignment and positioning method for lunar rovers by INS/CNS/odometer integrated navigation. The method can estimate not only the position and attitude errors, but also the biases of the accelerometers and gyros using the standard Kalman filter. The differences between the platform star azimuth, elevation angles and the computed star azimuth, elevation angles, and the difference between the velocity measured by odometer and the velocity measured by inertial sensors are taken as measurements. The semi-physical experiments are implemented to demonstrate that the position error can reduce to 10 m and attitude error is within 2″ during 5 min. The experiment results prove that it is an effective and attractive initialization approach for lunar rovers.

Tank waste remediation system retrieval and disposal mission initial updated baseline summary

International Nuclear Information System (INIS)

Swita, W.R.

1998-01-01

This document provides a summary of the proposed Tank Waste Remediation System Retrieval and Disposal Mission Initial Updated Baseline (scope, schedule, and cost) developed to demonstrate the Tank Waste Remediation System contractor's Readiness-to-Proceed in support of the Phase 1B mission

Development of cationically initiated UV curable coating systems based on cyclo-aliphatic diepoxide, ENR, epoxidized poly-butadiene and epoxidized soybean oil

International Nuclear Information System (INIS)

Kumar, R.N.; Quah, S.H.; Kong, K.W.; Rozman, H.D.; Tin, W.C.

1999-01-01

Epoxidized Natural Rubber (ENR) had been earlier found to impart toughness to otherwise brittle epoxy resin. Since the high viscosity of solutions of ENR in reactive solvent glycidyl methacrylate,imposed a limitation to the incorporation of higher percentages of the elastomer to the epoxy systems, experiments were initiated to employ the liquid elastomer, namely, epoxidized polybutadiene In the formulations. 'Mixture Design', a statistical experimental design, was adopted to study the effect of compositional and process variables on the curing of surface coatings formulated from the above system by UV radiation initiated by cationic photo-initiators. This paper also reports the results of the experiments carded out with epoxidized soybean oil Employed as a flexibilizer in the cycloaliphatic epoxy-ENR system

Uniqueness Results for Weak Leray-Hopf Solutions of the Navier-Stokes System with Initial Values in Critical Spaces

Science.gov (United States)

Barker, T.

2018-03-01

The main subject of this paper concerns the establishment of certain classes of initial data, which grant short time uniqueness of the associated weak Leray-Hopf solutions of the three dimensional Navier-Stokes equations. In particular, our main theorem that this holds for any solenodial initial data, with finite L_2(R^3) norm, that also belongs to certain subsets of {it{VMO}}^{-1}(R^3). As a corollary of this, we obtain the same conclusion for any solenodial u0 belonging to L2(R^3)\\cap \\dot{B}^{-1+3/p}_{p,∞}(R^3), for any 3norm is sufficiently small, where 3

Piezoelectrically Initiated Pyrotechnic Igniter

Science.gov (United States)

Quince, Asia; Dutton, Maureen; Hicks, Robert; Burnham, Karen

2013-01-01

This innovation consists of a pyrotechnic initiator and piezoelectric initiation system. The device will be capable of being initiated mechanically; resisting initiation by EMF, RF, and EMI (electromagnetic field, radio frequency, and electromagnetic interference, respectively); and initiating in water environments and space environments. Current devices of this nature are initiated by the mechanical action of a firing pin against a primer. Primers historically are prone to failure. These failures are commonly known as misfires or hang-fires. In many cases, the primer shows the dent where the firing pin struck the primer, but the primer failed to fire. In devices such as "T" handles, which are commonly used to initiate the blowout of canopies, loss of function of the device may result in loss of crew. In devices such as flares or smoke generators, failure can result in failure to spot a downed pilot. The piezoelectrically initiated ignition system consists of a pyrotechnic device that plugs into a mechanical system (activator), which on activation, generates a high-voltage spark. The activator, when released, will strike a stack of electrically linked piezo crystals, generating a high-voltage, low-amperage current that is then conducted to the pyro-initiator. Within the initiator, an electrode releases a spark that passes through a pyrotechnic first-fire mixture, causing it to combust. The combustion of the first-fire initiates a primary pyrotechnic or explosive powder. If used in a "T" handle, the primary would ramp the speed of burn up to the speed of sound, generating a shock wave that would cause a high explosive to go "high order." In a flare or smoke generator, the secondary would produce the heat necessary to ignite the pyrotechnic mixture. The piezo activator subsystem is redundant in that a second stack of crystals would be struck at the same time with the same activation force, doubling the probability of a first strike spark generation. If the first

Measuring health systems strength and its impact: experiences from the African Health Initiative.

Science.gov (United States)

Sherr, Kenneth; Fernandes, Quinhas; Kanté, Almamy M; Bawah, Ayaga; Condo, Jeanine; Mutale, Wilbroad

2017-12-21

Health systems are essential platforms for accessible, quality health services, and population health improvements. Global health initiatives have dramatically increased health resources; however, funding to strengthen health systems has not increased commensurately, partially due to concerns about health system complexity and evidence gaps demonstrating health outcome improvements. In 2009, the African Health Initiative of the Doris Duke Charitable Foundation began supporting Population Health Implementation and Training Partnership projects in five sub-Saharan African countries (Ghana, Mozambique, Rwanda, Tanzania, and Zambia) to catalyze significant advances in strengthening health systems. This manuscript reflects on the experience of establishing an evaluation framework to measure health systems strength, and associate measures with health outcomes, as part of this Initiative. Using the World Health Organization's health systems building block framework, the Partnerships present novel approaches to measure health systems building blocks and summarize data across and within building blocks to facilitate analytic procedures. Three Partnerships developed summary measures spanning the building blocks using principal component analysis (Ghana and Tanzania) or the balanced scorecard (Zambia). Other Partnerships developed summary measures to simplify multiple indicators within individual building blocks, including health information systems (Mozambique), and service delivery (Rwanda). At the end of the project intervention period, one to two key informants from each Partnership's leadership team were asked to list - in rank order - the importance of the six building blocks in relation to their intervention. Though there were differences across Partnerships, service delivery and information systems were reported to be the most common focus of interventions, followed by health workforce and leadership and governance. Medical products, vaccines and technologies, and

Reverse atom transfer radical polymerization of methyl methacrylate initiated by AIBN/FeCl3/isophthalic acid system

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The reverse ATRP of MMA using AIBN/FeCl3/ isophthalic acid as the initiating system was successfully performed. The new initiating system can be used to synthesize PMMA with high molecular weight and narrow polydis- persity index. The polymerization shows 'living'/controlled characteristics. Compared with other initiating system used in reverse ATRP, the easy availability and non-toxicity of isophthalic acid make it very attractive.

FFTF initial fuel loading, preanalyses, and comparison with preliminary results

International Nuclear Information System (INIS)

Rothrock, R.B.; Daughtry, J.W.; Zimmerman, B.D.; Petrowicz, N.E.; Bennett, R.A.; Ombrellaro, P.A.

1980-02-01

Disadvantages of conventional loading from the center out were circumvented by loading one trisector at a time, and connecting the control rod drivelines in each sector after it was loaded so that the rods could be operated during the loading of subsequent trisectors. This sequence was interrupted once during the loading of the final sector, to achieve initial criticality at an approximately minimum critical loading and to measure absolute subcriticality by the rod drop technique. An in-core detector was preferable to the standard FTR ex-core detectors for monitoring the initial fuel loading. Consequently, special fission chambers were installed in an instrument thimble near the core center to monitor the initial fuel loading

Results from the coded aperture neutron imaging system

International Nuclear Information System (INIS)

Brubaker, Erik; Steele, John T.; Brennan, James S.; Marleau, Peter

2010-01-01

Because of their penetrating power, energetic neutrons and gamma rays (∼1 MeV) offer the best possibility of detecting highly shielded or distant special nuclear material (SNM). Of these, fast neutrons offer the greatest advantage due to their very low and well understood natural background. We are investigating a new approach to fast-neutron imaging - a coded aperture neutron imaging system (CANIS). Coded aperture neutron imaging should offer a highly efficient solution for improved detection speed, range, and sensitivity. We have demonstrated fast neutron and gamma ray imaging with several different configurations of coded masks patterns and detectors including an 'active' mask that is composed of neutron detectors. Here we describe our prototype detector and present some initial results from laboratory tests and demonstrations.

Global health initiative investments and health systems strengthening: a content analysis of global fund investments

OpenAIRE

Warren, Ashley E; Wyss, Kaspar; Shakarishvili, George; Atun, Rifat; de Savigny, Don

2013-01-01

Background: Millions of dollars are invested annually under the umbrella of national health systems strengthening. Global health initiatives provide funding for low- and middle-income countries through disease-oriented programmes while maintaining that the interventions simultaneously strengthen systems. However, it is as yet unclear which, and to what extent, system-level interventions are being funded by these initiatives, nor is it clear how much funding they allocate to disease-specific a...

77 FR 36014 - Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors

Science.gov (United States)

2012-06-15

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0134] Initial Test Program of Emergency Core Cooling... for public comment draft regulatory guide (DG), DG-1277, ``Initial Test Program of Emergency Core..., entitled, ``Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors,'' is...

Design, assembly, and initial use of a digital system for the closed-loop control of a nuclear research reactor

International Nuclear Information System (INIS)

Kwok, K.S.; Bernard, J.A.; Lanning, D.D.

1991-01-01

In this paper the design, implementation, and initial testing of a multiple-computer/single-task system for the closed-loop control of a nuclear research reactor is described. A major advantage of the multiple-computer approach is that generic safety-related software that remains invariant can be separated from the control law software that is updated as plant procedures change. This facilitates software validation. Also, this approach allows both real-time operation and high numerical throughput. System compatibility was achieved through design of a special passive back plane which enabled the otherwise incompatible components to be operated in an integrated system. This multiple-computer system, which was designated as the Advanced Control Computer System (ACCS), has been installed on the 5-MWt MIT Research Reactor. In addition to a description of both the system and its associated hardware and software interfaces, experimental results are presented from its initial trials

Initial results of high resolution L-H transition studies on DIII-D

International Nuclear Information System (INIS)

Wang, G; Rhodes, T L; Doyle, E J; Peebles, W A; Zeng, L; Burrell, K H; McKee, G R; Groebner, R J; Evans, T E

2004-01-01

Understanding the L-H transition in tokamaks has been an important area of research for more than two decades. High time resolution diagnostics on DIII-D allow detailed characterization of the L-H transition and, therefore, testing and benchmarking of theoretical models. An experiment was performed in DIII-D utilizing a novel, high temporal and spatial resolution reflectometer density profile system to measure densities from the SOL to the inside separatrix. Initial data analysis indicates different density profile evolution during L-H transitions in upper single-null and lower single-null divertor configuration plasmas. A detailed comparison of the density gradient and fluctuation changes is presented for these two cases

Initial results of high resolution L-H transition studies on DIII-D

Energy Technology Data Exchange (ETDEWEB)

Wang, G [Department of Electrical Engineering and PSTI, University of California, Los Angeles, CA 90095 (United States); Rhodes, T L [Department of Electrical Engineering and PSTI, University of California, Los Angeles, CA 90095 (United States); Doyle, E J [Department of Electrical Engineering and PSTI, University of California, Los Angeles, CA 90095 (United States); Peebles, W A [Department of Electrical Engineering and PSTI, University of California, Los Angeles, CA 90095 (United States); Zeng, L [Department of Electrical Engineering and PSTI, University of California, Los Angeles, CA 90095 (United States); Burrell, K H [General Atomics, PO Box 85608, San Diego, CA 92186 (United States); McKee, G R [University of Wisconsin-Madison, 1500 Engineering Drive, Madison, WI 53706 (United States); Groebner, R J [General Atomics, PO Box 85608, San Diego, CA 92186 (United States); Evans, T E [General Atomics, PO Box 85608, San Diego, CA 92186 (United States)

2004-05-01

Understanding the L-H transition in tokamaks has been an important area of research for more than two decades. High time resolution diagnostics on DIII-D allow detailed characterization of the L-H transition and, therefore, testing and benchmarking of theoretical models. An experiment was performed in DIII-D utilizing a novel, high temporal and spatial resolution reflectometer density profile system to measure densities from the SOL to the inside separatrix. Initial data analysis indicates different density profile evolution during L-H transitions in upper single-null and lower single-null divertor configuration plasmas. A detailed comparison of the density gradient and fluctuation changes is presented for these two cases.

Automation and robotics for the Space Exploration Initiative: Results from Project Outreach

Science.gov (United States)

Gonzales, D.; Criswell, D.; Heer, E.

1991-01-01

A total of 52 submissions were received in the Automation and Robotics (A&R) area during Project Outreach. About half of the submissions (24) contained concepts that were judged to have high utility for the Space Exploration Initiative (SEI) and were analyzed further by the robotics panel. These 24 submissions are analyzed here. Three types of robots were proposed in the high scoring submissions: structured task robots (STRs), teleoperated robots (TORs), and surface exploration robots. Several advanced TOR control interface technologies were proposed in the submissions. Many A&R concepts or potential standards were presented or alluded to by the submitters, but few specific technologies or systems were suggested.

Initial clinical results of linac-based stereotactic radiosurgery and stereotactic radiotherapy for pituitary adenomas

International Nuclear Information System (INIS)

Mitsumori, Michihide; Shrieve, Dennis C.; Alexander, Eben; Kaiser, Ursula B.; Richardson, Gary E.; Black, Peter McL.; Loeffler, Jay S.

1998-01-01

Purpose: To retrospectively evaluate the initial clinical results of stereotactic radiosurgery (SRS) and fractionated stereotactic radiotherapy (SRT) for pituitary adenomas with regard to tumor and hormonal control and adverse effects of the treatment. Subjects and Methods: Forty-eight patients with pituitary adenoma who underwent SRS or SRT between September 1989 and September 1995 were analyzed. Of these, 18 received SRS and 30 received SRT. The median tumor volumes were 1.9 cm 3 for SRS and 5.7 cm 3 for SRT. Eleven of the SRS and 18 of the SRT patients were hormonally active at the time of the initial diagnosis. Four of the SRS and none of the SRT patients had a history of prior radiation therapy. Both SRS and SRT were performed using a dedicated stereotactic 6-MV linear accelerator (LINAC). The dose and normalization used for the SRS varied from 1000 cGy at 85% of the isodose line to 1500 cGy at 65% of the isodose line. For SRT patients, a total dose of 4500 cGy at 90% or 95% of the isodose line was delivered in 25 fractions of 180 cGy daily doses. Results: Disease control--The three year tumor control rate was 91.1% (100% for SRS and 85.3% for SRT). Normalization of the hormonal abnormality was achieved in 47% of the 48 patients (33% for SRS and 54% for SRT). The average time required for normalization was 8.5 months for SRS and 18 months for SRT. Adverse effects--The 3-year rate of freedom from central nervous system adverse effects was 89.7% (72.2% for SRS and 100% for SRT). Three patients who received SRS for a tumor in the cavernous sinus developed a ring enhancement in the temporal lobe as shown by follow-up magnetic resonance imaging. Two of these cases were irreversible and were considered to be radiation necrosis. None of the 48 patients developed new neurocognitive or visual disorders attributable to the irradiation. The incidence of endocrinological adverse effects were similar in the two groups, resulting in 3-year rates of freedom from newly

Afghanistan Digital Library Initiative: Revitalizing an Integrated Library System

Directory of Open Access Journals (Sweden)

Yan HAN

2007-12-01

Full Text Available This paper describes an Afghanistan digital library initiative of building an integrated library system (ILS for Afghanistan universities and colleges based on open-source software. As one of the goals of the Afghan eQuality Digital Libraries Alliance, the authors applied systems analysis approach, evaluated different open-source ILSs, and customized the selected software to accommodate users’ needs. Improvements include Arabic and Persian language support, user interface changes, call number label printing, and ISBN-13 support. To our knowledge, this ILS is the first at a large academic library running on open-source software.

Initial CGE Model Results Summary Exogenous and Endogenous Variables Tests

Energy Technology Data Exchange (ETDEWEB)

Edwards, Brian Keith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boero, Riccardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rivera, Michael Kelly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-07

The following discussion presents initial results of tests of the most recent version of the National Infrastructure Simulation and Analysis Center Dynamic Computable General Equilibrium (CGE) model developed by Los Alamos National Laboratory (LANL). The intent of this is to test and assess the model’s behavioral properties. The test evaluated whether the predicted impacts are reasonable from a qualitative perspective. This issue is whether the predicted change, be it an increase or decrease in other model variables, is consistent with prior economic intuition and expectations about the predicted change. One of the purposes of this effort is to determine whether model changes are needed in order to improve its behavior qualitatively and quantitatively.

Copolymerization of propene and styrene using a zirconocene - methylaluminoxane initiator system

International Nuclear Information System (INIS)

Rabagliati, F.M.; Rodriguez, F.J.; Quijada, R.; Galland, G.B.

2009-01-01

The copolymerization of propene with styrene has been tested using the rac-Et(Ind) 2 ZrCl 2 -methylaluminoxane initiator system. The various proportion of styrene in initial feed showed an important effect on the polymerization activity. Low contents of styrene in the reaction produced a considerable fall in the activity. Respect to thermal behavior, it is noted that obtained propene/styrene copolymers showed Tm values slightly lower than the corresponding polypropene one. NMR spectroscopy allowed to confirm that the copolymer composition includes a very low incorporation of styrene in polypropylene chains. (author)

Design of an Object-Oriented Turbomachinery Analysis Code: Initial Results

Science.gov (United States)

Jones, Scott M.

2015-01-01

Performance prediction of turbomachines is a significant part of aircraft propulsion design. In the conceptual design stage, there is an important need to quantify compressor and turbine aerodynamic performance and develop initial geometry parameters at the 2-D level prior to more extensive Computational Fluid Dynamics (CFD) analyses. The Object-oriented Turbomachinery Analysis Code (OTAC) is being developed to perform 2-D meridional flowthrough analysis of turbomachines using an implicit formulation of the governing equations to solve for the conditions at the exit of each blade row. OTAC is designed to perform meanline or streamline calculations; for streamline analyses simple radial equilibrium is used as a governing equation to solve for spanwise property variations. While the goal for OTAC is to allow simulation of physical effects and architectural features unavailable in other existing codes, it must first prove capable of performing calculations for conventional turbomachines. OTAC is being developed using the interpreted language features available in the Numerical Propulsion System Simulation (NPSS) code described by Claus et al (1991). Using the NPSS framework came with several distinct advantages, including access to the pre-existing NPSS thermodynamic property packages and the NPSS Newton-Raphson solver. The remaining objects necessary for OTAC were written in the NPSS framework interpreted language. These new objects form the core of OTAC and are the BladeRow, BladeSegment, TransitionSection, Expander, Reducer, and OTACstart Elements. The BladeRow and BladeSegment consumed the initial bulk of the development effort and required determining the equations applicable to flow through turbomachinery blade rows given specific assumptions about the nature of that flow. Once these objects were completed, OTAC was tested and found to agree with existing solutions from other codes; these tests included various meanline and streamline comparisons of axial

Flight demonstration of flight termination system and solid rocket motor ignition using semiconductor laser initiated ordnance

Science.gov (United States)

Schulze, Norman R.; Maxfield, B.; Boucher, C.

1995-01-01

Solid State Laser Initiated Ordnance (LIO) offers new technology having potential for enhanced safety, reduced costs, and improved operational efficiency. Concerns over the absence of programmatic applications of the technology, which has prevented acceptance by flight programs, should be abated since LIO has now been operationally implemented by the Laser Initiated Ordnance Sounding Rocket Demonstration (LOSRD) Program. The first launch of solid state laser diode LIO at the NASA Wallops Flight Facility (WFF) occurred on March 15, 1995 with all mission objectives accomplished. This project, Phase 3 of a series of three NASA Headquarters LIO demonstration initiatives, accomplished its objective by the flight of a dedicated, all-LIO sounding rocket mission using a two-stage Nike-Orion launch vehicle. LIO flight hardware, made by The Ensign-Bickford Company under NASA's first Cooperative Agreement with Profit Making Organizations, safely initiated three demanding pyrotechnic sequence events, namely, solid rocket motor ignition from the ground and in flight, and flight termination, i.e., as a Flight Termination System (FTS). A flight LIO system was designed, built, tested, and flown to support the objectives of quickly and inexpensively putting LIO through ground and flight operational paces. The hardware was fully qualified for this mission, including component testing as well as a full-scale system test. The launch accomplished all mission objectives in less than 11 months from proposal receipt. This paper concentrates on accomplishments of the ordnance aspects of the program and on the program's implementation and results. While this program does not generically qualify LIO for all applications, it demonstrated the safety, technical, and operational feasibility of those two most demanding applications, using an all solid state safe and arm system in critical flight applications.

STUDIES ON RADICAL POLYMERIZATION OF METHYL METHACRYLATE INITIATED WITH ORGANIC PEROXIDE-AMINE SYSTEMS

Institute of Scientific and Technical Information of China (English)

QIU Kunyuan; SHUI Li; FENG Xinde

1984-01-01

Radical polymerization of methyl methacrylate (MMA) initiated with various diacyl peroxideamine systems was studied. Benzoyl peroxide (BPO) and lauroyl peroxide (LPO) were used as diacyl peroxide component, N,N-dimethyl aniline (DMA) and its para substituted derivatives, i.e., N,N-dimethyl-p-toluidine (DMT), p-hydroxymethyl-N,N-dimethyl aniline (HDMA), p-nitro-N,N-dimethyl aniline (NDMA) and p-dimethylamino benzaldehyde (DMAB) were used as amine components. It was found that the peroxide-DMT systems give higher rates of bulk polymerization Rp of MMA than the organic hydroperoxide-DMT systems with the following descending order BPO-DMT＞LPO-DMT＞CHP (cumene hydroperoxide)-DMT＞TBH (tert-butyl hydroperoxide)-DMT.The aromatic tertiary amines possess obvious structural effect on the Rp values in the diacyl peroxideamine system. The overall activation energy of MMA polymerization was determined and the kinetics of polymerization of MMA initiated with BPO-DMT system was investigated.

Design aspects of automation system for initial processing of fecal samples

International Nuclear Information System (INIS)

Sawant, Pramilla D.; Prabhu, Supreetha P.; Suja, A.; Wankhede, Sonal; Chaudhary, Seema; Rao, D.D.; Pradeepkumar, K.S.; Das, A.P.; Badodkar, B.D.

2014-01-01

The procedure for initial handling of the fecal samples at Bioassay Lab., Trombay is as follows: overnight fecal samples are collected from the worker in a kit consisting of a polythene bag placed in a wide mouth polythene container closed with an inner lid and a screw cap. Occupational worker collects the sample in the polythene bag. On receiving the sample, the polythene container along with the sample is weighed, polythene bag containing fecal sample is lifted out of the container using a pair of tongs placed inside a crucible and ashed inside a muffle furnace at 450℃. After complete ashing, the crucible containing white ash is taken-up for further radiochemical processing. This paper describes the various steps in developing a prototype automated system for initial handling of fecal samples. The proposed system for handling and processing of fecal samples is proposed to automate the above. The system once developed will help eliminate manual intervention till the ashing stage and reduce the biological hazard involved in handling such samples mentioned procedure

Initial Results from the Lost Alpha Diagnostics on Joint European Torus

Energy Technology Data Exchange (ETDEWEB)

Darrow, Doug; Cecil, Ed; Ellis, Bob; Fullard, Keith; Hill, Ken; Horton, Alan; Kiptily, Vasily; Pedrick, Les; Reich, Matthias

2007-07-25

Two devices have been installed in the Joint European Torus (JET) vacuum vessel near the plasma boundary to investigate the loss of energetic ions and fusion products in general and alpha particles in particular during the upcoming JET experiments. These devices are (i) a set of multichannel thin foil Faraday collectors, and (ii) a well collimated scintillator which is optically connected to a charge-coupled device. Initial results, including the radial energy and poloidal dependence of lost ions from hydrogen and deuterium plasmas during the 2005–06 JET restart campaign, will be presented.

Initial Results from the Lost Alpha Diagnostics on Joint European Torus

International Nuclear Information System (INIS)

Darrow, Doug; Baeumel, Stefan; Cecil, Ed; Ellis, Bob; Fullard, Keith; Hill, Ken; Horton, Alan; Kiptily, Vasily; Pedrick, Les; Reich, Matthias; Werner, Andreas

2007-01-01

Two devices have been installed in the Joint European Torus (JET) vacuum vessel near the plasma boundary to investigate the loss of energetic ions and fusion products in general and alpha particles in particular during the upcoming JET experiments. These devices are (i) a set of multichannel thin foil Faraday collectors, and (ii) a well collimated scintillator which is optically connected to a charge-coupled device. Initial results, including the radial energy and poloidal dependence of lost ions from hydrogen and deuterium plasmas during the 2005-06 JET restart campaign, will be presented.

IoT-based electricity load optimisation: initial results of a monitor and control system

CSIR Research Space (South Africa)

Smith, Andrew C

2012-11-01

Full Text Available by means of electromagnetic induction sensors. These readings are sent wirelessly to a central receiver where the data is converted into a format accessible over the internet. Switching current to appliances is done with the aid of a microcontroller... circuit interfaced to the internet. The microcontroller reacts to commands received from a geographically remote software system. This software system incorporates a rules-engine that monitors data from the sensors and considers the priority of each...

78 FR 63516 - Initial Test Program of Emergency Core Cooling Systems for New Boiling-Water Reactors

Science.gov (United States)

2013-10-24

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0134] Initial Test Program of Emergency Core Cooling....79.1, ``Initial Test Program of Emergency Core Cooling Systems for New Boiling-Water Reactors.'' This... emergency core cooling systems (ECCSs) for boiling- water reactors (BWRs) whose licenses are issued after...

Raydet non-electric blast initiation system for efficient and environment-friendly surface blasts

Energy Technology Data Exchange (ETDEWEB)

Sarathy, M.O. [IDL Chemicals Ltd., Hyderabad (India). Technical Services Cell

1995-08-01

This paper discusses the advantages of using the Raydet shock tube based blast initiation system and reviews research work carried out on release of explosive energy in the drillhole, effect of stemming retention (stemming effectiveness) and advantages of `true bottom hole initiation` of drillholes in surface blasting. Some case studies are presented. 6 refs., 5 figs., 1 tab.

Sensitivity Analysis of FEAST-Metal Fuel Performance Code: Initial Results

International Nuclear Information System (INIS)

Edelmann, Paul Guy; Williams, Brian J.; Unal, Cetin; Yacout, Abdellatif

2012-01-01

This memo documents the completion of the LANL milestone, M3FT-12LA0202041, describing methodologies and initial results using FEAST-Metal. The FEAST-Metal code calculations for this work are being conducted at LANL in support of on-going activities related to sensitivity analysis of fuel performance codes. The objective is to identify important macroscopic parameters of interest to modeling and simulation of metallic fuel performance. This report summarizes our preliminary results for the sensitivity analysis using 6 calibration datasets for metallic fuel developed at ANL for EBR-II experiments. Sensitivity ranking methodology was deployed to narrow down the selected parameters for the current study. There are approximately 84 calibration parameters in the FEAST-Metal code, of which 32 were ultimately used in Phase II of this study. Preliminary results of this sensitivity analysis led to the following ranking of FEAST models for future calibration and improvements: fuel conductivity, fission gas transport/release, fuel creep, and precipitation kinetics. More validation data is needed to validate calibrated parameter distributions for future uncertainty quantification studies with FEAST-Metal. Results of this study also served to point out some code deficiencies and possible errors, and these are being investigated in order to determine root causes and to improve upon the existing code models.

Implementation of STUD Pulses at the Trident Laser and Initial Results

Science.gov (United States)

Johnson, R. P.; Shimada, T.; Montgomery, D. S.; Afeyan, B.; Hüller, S.

2012-10-01

Controlling and mitigating laser-plasma instabilities such as stimulated Brillouin scattering, stimulated Raman scattering, and crossed-beam energy transfer is important to achieve high-gain inertial fusion using laser drivers. Recent theory and simulations show that these instabilities can be largely controlled using laser pulses consisting of spike trains of uneven duration and delay (STUD) by modulating the laser on a picosecond time scale [1,2]. We have designed and implemented a STUD pulse generator at the LANL Trident Laser Facility using Fourier synthesis to produce a 0.5-ns envelope of psec-duration STUD pulses using a spatial light modulator. Initial results from laser propagation tests and measurements as well as initial laser-plasma characterization experiments will be presented.[4pt] [1] B. Afeyan and S. H"uller, ``Optimal Control of Laser Plasma Instabilities using STUD pulses,'' IFSA 2011, P.Mo.1, to appear in Euro. Phys. J. Web of Conf. (2012).[2] S. H"uller and B. Afeyan, ``Simulations of drastically reduced SBS with STUD pulses,'' IFSA 2011, O.Tu8-1, to appear in Euro. Phys. J. Web of Conf. (2012).

Results from the fielding of the Bio-surveillance Analysis, Feedback, Evaluation and Response (B-SAFER) system in Albuquerque, New Mexico.

Science.gov (United States)

Forslund, David; Umland, Edith; Brillman, Judith C; Joyce, Ed; Froman, Philip; Burr, Tom; Judd, Stephen L; Picard, Richard; Wokoun, Doug; Joner, Mike; Sewell, C Mack

2003-01-01

Public health authorities need a surveillance system that is sensitive enough to detect a disease outbreak early to enable a proper response. In order to meet this challenge we have deployed a pilot component-based system in Albuquerque, NM as part of the National Biodefense Initiative (BDI). B-SAFER gathers routinely collected data from healthcare institutions to monitor disease events in the community. We describe initial results from the deployment of the system for the past 6 months

NICER observations of highly magnetized neutron stars: Initial results

Science.gov (United States)

Enoto, Teruaki; Arzoumanian, Zaven; Gendreau, Keith C.; Nynka, Melania; Kaspi, Victoria; Harding, Alice; Guver, Tolga; Lewandowska, Natalia; Majid, Walid; Ho, Wynn C. G.; NICER Team

2018-01-01

The Neutron star Interior Composition Explorer (NICER) was launched on June 3, 2017, and attached to the International Space Station. The large effective area of NICER in soft X-rays makes it a powerful tool not only for its primary science objective (diagnostics of the nuclear equation state) but also for studying neutron stars of various classes. As one of the NICER science working groups, the Magnetars and Magnetospheres (M&M) team coordinates monitoring and target of opportunity (ToO) observations of magnetized neutron stars, including magnetars, high-B pulsars, X-ray dim isolated neutron stars, and young rotation-powered pulsars. The M&M working group has performed simultaneous X-ray and radio observations of the Crab and Vela pulsars, ToO observations of the active anomalous X-ray pulsar 4U 0142+61, and a monitoring campaign for the transient magnetar SGR 0501+4516. Here we summarize the current status and initial results of the M&M group.

Project Management Plan for Initial Tank Retrieval Systems, Project W-211

International Nuclear Information System (INIS)

VAN BEEK, J.E.

1999-01-01

Project W-211, Initial Tank Retrieval Systems (ITRS), is a fiscal year 1994 Major Systems Acquisition that will provide systems for retrieval of radioactive wastes from selected double-shell tanks (DST). The contents of these tanks are a combination of supernatant liquids and settled solids. To retrieve waste from the tanks, it is first necessary to mix the liquid and solids prior to transferring the slurry to alternative storage or treatment facilities. The ITRS will provide systems to mobilize the settled solids and transfer the wastes out of the tanks. In so doing, ITRS provides feed for future processing plants, allows for consolidation of tank solids to manage space within existing DST storage capacity, and supports continued safe storage of tank waste. The ITRS scope has been revised to include waste retrieval systems for tanks AP-102, AP-104, AP-108, AN-103, AN-104, AN-105, AY-102, AZ-102, and SY-102. This current tank selection and sequence provides retrieval systems supporting the Privatized waste processing plant and sustains the ability to provide final remediation of several watch list DSTs via treatment. The ITRS is configured to support changing program needs, as constrained by available budget, by maintaining the flexibility for exchanging tanks requiring mixer pump-based retrieval systems and shifting the retrieval sequence. Preliminary design was configured such that an adequate basis exists for initiating Title II design of a mixer pump based retrieval system for any DST. This Project Management Plan (PMP) documents the methodology for managing the ITRS, formalizes organizational responsibilities and interfaces, and identifies project requirements such as change control, design verification, systems engineering, and human factors engineering

Solutions Stability of Initial Boundary Problem, Modeling of Dynamics of Some Discrete Continuum Mechanical System

Directory of Open Access Journals (Sweden)

D. A. Eliseev

2015-01-01

Full Text Available The solution stability of an initial boundary problem for a linear hybrid system of differential equations, which models the rotation of a rigid body with two elastic rods located in the same plane is studied in the paper. To an axis passing through the mass center of the rigid body perpendicularly to the rods location plane is applied the stabilizing moment proportional to the angle of the system rotation, derivative of the angle, integral of the angle. The external moment provides a feedback. A method of studying the behavior of solutions of the initial boundary problem is proposed. This method allows to exclude from the hybrid system of differential equations partial differential equations, which describe the dynamics of distributed elements of a mechanical system. It allows us to build one equation for an angle of the system rotation. Its characteristic equation defines the stability of solutions of all the system. In the space of feedback-coefficients the areas that provide the asymptotic stability of solutions of the initial boundary problem are built up.

The Initial Development of a Computerized Operator Support System

Energy Technology Data Exchange (ETDEWEB)

Roger Lew; Ronald L Boring; Thomas A Ulrich; Ken Thomas

2014-08-01

A computerized operator support system (COSS) is a collection of resilient software technologies to assist operators in monitoring overall nuclear power plant performance and making timely, informed decisions on appropriate control actions for the projected plant condition. The COSS provides rapid assessments, computations, and recommendations to reduce workload and augment operator judgment and decision-making during fast- moving, complex events. A prototype COSS for a chemical volume control system at a nuclear power plant has been developed in order to demonstrate the concept and provide a test bed for further research. The development process identified four underlying elements necessary for the prototype, which consist of a digital alarm system, computer-based procedures, piping and instrumentation diagram system representations, and a recommender module for mitigation actions. An operational prototype resides at the Idaho National Laboratory (INL) using the U.S. Department of Energy’s (DOE) Light Water Reactor Sustainability (LWRS) Human Systems Simulation Laboratory (HSSL). Several human-machine interface (HMI) considerations are identified and incorporated in the prototype during this initial round of development.

Design of Bus Protocol Intelligent Initiation System Based On RS485

Directory of Open Access Journals (Sweden)

Li Liming

2017-01-01

Full Text Available In order to design an effective and reliable RS485 bus protocol based on RS485 bus, this paper introduces the structure and transmission mode of the command frame and the response frame, and also introduce four control measures and the communication in order to process quality of this system. The communication protocol is open, tolerant, reliable and fast, and can realize ignition more reliable and accurate in the intelligent initiation system.

Kinetics of Waterborne Alkyd/Acrylic Hybrid Resin Free Radical Polymerization by Two Systems of Redox and Thermal Initiators

Directory of Open Access Journals (Sweden)

shirin Madadi

2012-12-01

Full Text Available Kinetics of radical polymerizations of waterborne alkyd/acrylic hybrid resin via batch mini-emulsion technique was studied using redox initiators (TBHP/Fe2+/EDTA/AsAc  and  TBHP/Fe2+/EDTA/SFS at relatively low temperatures and thermal initiators (BPO, KPS and AIBN at higher temperatures to seek the most suitable initiator system. At the end of all reactions the unreacted monomer content was reduced using post-polymerization technique; consequently, leading to increased monomer conversion and flm formation with improved properties. The kinetics of mini-emulsion polymerization showed that in all redox initiator systems (Fe2+ catalyst + EDTA chelating agent, the radials are produced at relatively low temperature with more effcient control of the reactor temperature. It was found that at 45°C TBHP/Fe2+/EDTA/SFS redox initiator system leads to 98% monomer conversion, a much higher rate than that of systems involved thermal initiators.

Reduction of initial shock in decadal predictions using a new initialization strategy

Science.gov (United States)

He, Yujun; Wang, Bin; Liu, Mimi; Liu, Li; Yu, Yongqiang; Liu, Juanjuan; Li, Ruizhe; Zhang, Cheng; Xu, Shiming; Huang, Wenyu; Liu, Qun; Wang, Yong; Li, Feifei

2017-08-01

A novel full-field initialization strategy based on the dimension-reduced projection four-dimensional variational data assimilation (DRP-4DVar) is proposed to alleviate the well-known initial shock occurring in the early years of decadal predictions. It generates consistent initial conditions, which best fit the monthly mean oceanic analysis data along the coupled model trajectory in 1 month windows. Three indices to measure the initial shock intensity are also proposed. Results indicate that this method does reduce the initial shock in decadal predictions by Flexible Global Ocean-Atmosphere-Land System model, Grid-point version 2 (FGOALS-g2) compared with the three-dimensional variational data assimilation-based nudging full-field initialization for the same model and is comparable to or even better than the different initialization strategies for other fifth phase of the Coupled Model Intercomparison Project (CMIP5) models. Better hindcasts of global mean surface air temperature anomalies can be obtained than in other FGOALS-g2 experiments. Due to the good model response to external forcing and the reduction of initial shock, higher decadal prediction skill is achieved than in other CMIP5 models.

Initial Results from the Kwajalein Micrometeorite Collections

Science.gov (United States)

Wozniakiewicz, P. J.; Bradley, J. P.; Price, M. C.; Zolensky, M. E.; Ishii, H. A.; Brownlee, D. E.; Dearborn, D.; Jones, T.; Barnett, B.; Yakuma, S.;

An Initiating-Event Analysis for PSA of Hanul Units 3 and 4: Results and Insights

International Nuclear Information System (INIS)

Kim, Dong-San; Park, Jin Hee

2015-01-01

As a part of the PSA, an initiating-event (IE) analysis was newly performed by considering the current state of knowledge and the requirements of the ASME/ANS probabilistic risk assessment (PRA) standard related to IE analysis. This paper describes the methods of, results and some insights from the IE analysis for the PSA of the Hanul units 3 and 4. In this study, as a part of the PSA for the Hanul units 3 and 4, an initiating-event (IE) analysis was newly performed by considering the current state of knowledge and the requirements of the ASME/ANS probabilistic risk assessment (PRA) standard. In comparison with the previous IE analysis, this study performed a more systematic and detailed analysis to identify potential initiating events, and calculated the IE frequencies by using the state-of-the-art methods and the latest data. As a result, not a few IE frequencies are quite different from the previous frequencies, which can change the major accident sequences obtained from the quantification of the PSA model

Grassroots Initiatives as Sustainability Transition Pioneers: Implications and Lessons for Urban Food Systems

Directory of Open Access Journals (Sweden)

Maria Gernert

2018-03-01

Full Text Available This review explores the current evidence on the role and success factors of grassroots initiatives in sustainability transitions, with special attention given to social innovations and the transformation of urban food systems, a field that is still rather scantly dealt with in literature compared to technological innovations in other sectors such as energy. In addition to their contributions to get the necessary transformation towards sustainable futures off the ground, the preconditions for grassroots initiatives to thrive are presented—as well as limitations regarding their possibilities and the challenges they face. Increasingly, the importance of civil society and social movements in facilitating societal transformation is recognized by both researchers and policy makers. Within their radical niches, grassroots initiatives do not have to adhere to the logics of the wider systems in which they are embedded. This allows them to experiment with diverse solutions to sustainability challenges such as local food security and sovereignty. By means of democratic, inclusive and participatory processes, they create new pathways and pilot a change of course. Nevertheless, upscaling often comes at the loss of the transformative potential of grassroots initiatives.

Initial Results from Lunar Electromagnetic Sounding with ARTEMIS

Science.gov (United States)

Fuqua, H.; Fatemi, S.; Poppe, A. R.; Delory, G. T.; Grimm, R. E.; De Pater, I.

2016-12-01

Electromagnetic Sounding constrains conducting layers of the lunar interior by observing variations in the Interplanetary Magnetic Field. Here, we focus our analysis on the time domain transfer function method locating transient events observed by two magnetometers near the Moon. We analyze ARTEMIS and Apollo magnetometer data. This analysis assumes the induced field responds undisturbed in a vacuum. In actuality, the dynamic plasma environment interacts with the induced field. Our models indicate distortion but not confinement occurs in the nightside wake cavity. Moreover, within the deep wake, near-vacuum region, distortion of the induced dipole fields due to the interaction with the wake is minimal depending on the magnitude of the induced field, the geometry of the upstream fields, and the upstream plasma parameters such as particle densities, solar wind velocity, and temperatures. Our results indicate the assumption of a vacuum dipolar response is reasonable within this minimally disturbed zone. We then interpret the ATEMIS magnetic field signal through a geophysical forward model capturing the induced response based on prescribed electrical conductivity models. We demonstrate our forward model passes benchmarking analyses and solves the magnetic induction response for any input signal as well as any 2 or 3 dimensional conductivity profile. We locate data windows according to the following criteria: (1) probe locations such that the wake probe is within 500km altitude within the wake cavity and minimally disturbed zone, and the second probe is in the free streaming solar wind; (2) a transient event consisting of an abrupt change in the magnetic field occurs enabling the observation of induction; (3) cross correlation analysis reveals the magnetic field signals are well correlated between the two probes and distances observed. Here we present initial ARTEMIS results providing further insight into the lunar interior structure. This method and modeling results

Teacher Incentive Systems, Final Report. Policy Research Initiative: Haiti, Liberia, Somalia, Yemen Arab Republic.

Science.gov (United States)

Kemmerer, Frances; Thiagarajan, Sivasailam

Findings of a study that examined the implementation of a teacher incentives initiative in four countries--Haiti, Liberia, Somalia, and Yemen--are presented in this paper. The countries are participating in a 10-year initiative founded in 1984, Improving the Efficiency of Educational Systems (IEES). Methodology involved interviews with…

Initial results from the Auto/Oil Air Quality Improvement Research Program

International Nuclear Information System (INIS)

McCabe, L.J.

1993-01-01

The Auto/Air Quality Improvement Research Program (AQIRP), a cooperative effort by the three major US auto companies and fourteen oil companies, is the most comprehensive research effort ever undertaken to develop data on the air quality effects of the use of various motor fuels in various automotive systems and the relative cost-effectiveness of various fuel/vehicle combinations. Phase 1 of the Program, at a cost of about $15 million, is examining emissions and air quality impacts from current and older vehicles using reformulated gasolines with widely different values of aromatics content, olefin content, oxygenate content and type, sulfur content, vapor pressure (RVP) and 90% distillation temperature. Emissions from Flexible and Variable Fuel vehicles using methanol/gasoline mixtures are also being examined. A second phase with a $25 million budget over three years has also been approved. Initial findings for the Phase 1 study and Phase 2 plans are presented

Initial Perceptions of Open Higher Education Students with Learner Management Systems

Directory of Open Access Journals (Sweden)

Asu ALTUNOGLU

2017-07-01

Full Text Available Learner management systems (LMS are used in open education as a means of managing and recording e-learning facilities as well as improving student engagement. Students benefit from them to become active participants in the decision-making process of their own learning. This study aims to investigate the initial perceptions of students experiencing the LMS for the first time in the Open Education System of Anadolu University with the purpose of identifying the effective and ineffective aspects of it from their perspective and their demands and suggestions for how to improve their the engagement in the system. To do this, an interpretive qualitative case study research design was used in order to focus on individual contexts and perceptions formed within those contexts. According to the findings, students were found to have highly personalized and customized user habits and engagement levels with the LMS depending on their varying ages, occupational statuses, IT capacities, and educational backgrounds. In terms of their satisfaction with the LMS, the quality, quantity and variety of content in LMS was found to have a major influence on their initial perceptions of satisfaction.

Local, organic food initiatives and their potentials for transforming the conventional food system

Directory of Open Access Journals (Sweden)

Geir Lieblein

2005-05-01

Full Text Available L’objectif de cet article est de discuter l’importance des initiatives locales dans la distribution de produits biologiques. Le sujet est abordé d’une part en fonction de la relation entre ce type d’initiatives et le système agroalimentaire conventionnel et d’autre part en fonction de la possibilité du développement d’un système agroalimentaire plus durable. Basé sur trois études scandinaves, concernant des produits biologiques en Norvège et au Danemark, cet article souligne le fait que les différents acteurs intreviewés jouent à la fois sur le tableau du local et du biologique et sur le tableau du conventionnel. En dépit de différences structurelles distinctes, les deux systèmes, et les conventions qui leur sont rattachées, s’influencent mutuellement. Afin de mettre au point une agriculture plus durable, il semble donc important de mettre en valeur le fondement global de l’agriculture écologique, qui repose non seulement sur des valeurs biologiques et locales, mais encore sur des aspects économiques, sociaux et culturels qui doivent être pris en considération.The aim of this article is to discuss the importance of local initiatives for distribution of organic food. This subject is discussed both in relation to how such initiatives may affect the overall conventional food system and the possible implications for development of a more sustainable food system. The article is based on findings from three different cases of local, organic food in Norway and Denmark. We found that actors within the cases are both involved with local, organic food initiatives and at the same time part of the overall conventional food system. Even though there are distinctive structural differences between these distribution systems, they mutually affect each other. This means that conventions normally associated with local, organic food systems may ‘rub off’ to the conventional food system and vice versa. In order to develop

Preliminary Results of a U.S. Deep South Warm Season Deep Convective Initiation Modeling Experiment using NASA SPoRT Initialization Datasets for Operational National Weather Service Local Model Runs

Science.gov (United States)

Medlin, Jeffrey M.; Wood, Lance; Zavodsky, Brad; Case, Jon; Molthan, Andrew

2012-01-01

The initiation of deep convection during the warm season is a forecast challenge in the relative high instability and low wind shear environment of the U.S. Deep South. Despite improved knowledge of the character of well known mesoscale features such as local sea-, bay- and land-breezes, observations show the evolution of these features fall well short in fully describing the location of first initiates. A joint collaborative modeling effort among the NWS offices in Mobile, AL, and Houston, TX, and NASA s Short-term Prediction Research and Transition (SPoRT) Center was undertaken during the 2012 warm season to examine the impact of certain NASA produced products on the Weather Research and Forecasting Environmental Modeling System. The NASA products were: a 4-km Land Information System data, a 1-km sea surface temperature analysis, and a 4-km greenness vegetation fraction analysis. Similar domains were established over the southeast Texas and Alabama coastlines, each with a 9 km outer grid spacing and a 3 km inner nest spacing. The model was run at each NWS office once per day out to 24 hours from 0600 UTC, using the NCEP Global Forecast System for initial and boundary conditions. Control runs without the NASA products were made at the NASA SPoRT Center. The NCAR Model Evaluation Tools verification package was used to evaluate both the forecast timing and location of the first initiates, with a focus on the impacts of the NASA products on the model forecasts. Select case studies will be presented to highlight the influence of the products.

Discretizing LTI Descriptor (Regular Differential Input Systems with Consistent Initial Conditions

Directory of Open Access Journals (Sweden)

Athanasios D. Karageorgos

2010-01-01

Full Text Available A technique for discretizing efficiently the solution of a Linear descriptor (regular differential input system with consistent initial conditions, and Time-Invariant coefficients (LTI is introduced and fully discussed. Additionally, an upper bound for the error ‖x¯(kT−x¯k‖ that derives from the procedure of discretization is also provided. Practically speaking, we are interested in such kind of systems, since they are inherent in many physical, economical and engineering phenomena.

LWR aerosol containment experiments (LACE) program and initial test results

International Nuclear Information System (INIS)

Muhlestein, L.D.; Hilliard, R.K.; Bloom, G.R.; McCormack, J.D.; Rahn, F.J.

1985-01-01

The LWR aerosol containment experiments (LACE) program is described. The LACE program is being performed at the Hanford Engineer Development Laboratory (operated by Westinghouse Hanford Company) and the initial tests are sponsored by EPRI. The objectives of the LACE program are: to demonstrate, at large-scale, inherent radioactive aerosol retention behavior for postulated high consequence LWR accident situations; and to provide a data base to be used for aerosol behavior . Test results from the first phase of the LACE program are presented and discussed. Three large-scale scoping tests, simulating a containment bypass accident sequence, demonstrated the extent of agglomeration and deposition of aerosols occurring in the pipe pathway and vented auxiliary building under realistic accident conditions. Parameters varied during the scoping tests were aerosol type and steam condensation

75 FR 16739 - EDA Participation in the Energy Efficient Building Systems Regional Innovation Cluster Initiative

Science.gov (United States)

2010-04-02

...: Promote regional development; Accelerate innovation, technology transfer, and entrepreneurship to create... priorities, which are: Collaborative Regional Innovation. Initiatives that support the development and growth... Participation in the Energy Efficient Building Systems Regional Innovation Cluster Initiative AGENCY: Economic...

Breast imaging with the SoftVue imaging system: first results

Science.gov (United States)

Duric, Neb; Littrup, Peter; Schmidt, Steven; Li, Cuiping; Roy, Olivier; Bey-Knight, Lisa; Janer, Roman; Kunz, Dave; Chen, Xiaoyang; Goll, Jeffrey; Wallen, Andrea; Zafar, Fouzaan; Allada, Veerendra; West, Erik; Jovanovic, Ivana; Li, Kuo; Greenway, William

2013-03-01

For women with dense breast tissue, who are at much higher risk for developing breast cancer, the performance of mammography is at its worst. Consequently, many early cancers go undetected when they are the most treatable. Improved cancer detection for women with dense breasts would decrease the proportion of breast cancers diagnosed at later stages, which would significantly lower the mortality rate. The emergence of whole breast ultrasound provides good performance for women with dense breast tissue, and may eliminate the current trade-off between the cost effectiveness of mammography and the imaging performance of more expensive systems such as magnetic resonance imaging. We report on the performance of SoftVue, a whole breast ultrasound imaging system, based on the principles of ultrasound tomography. SoftVue was developed by Delphinus Medical Technologies and builds on an early prototype developed at the Karmanos Cancer Institute. We present results from preliminary testing of the SoftVue system, performed both in the lab and in the clinic. These tests aimed to validate the expected improvements in image performance. Initial qualitative analyses showed major improvements in image quality, thereby validating the new imaging system design. Specifically, SoftVue's imaging performance was consistent across all breast density categories and had much better resolution and contrast. The implications of these results for clinical breast imaging are discussed and future work is described.

Site initialization, recovery, and back-up in a distributed database system

International Nuclear Information System (INIS)

Attar, R.; Bernstein, P.A.; Goodman, N.

1982-01-01

Site initialization is the problem of integrating a new site into a running distributed database system (DDBS). Site recovery is the problem of integrating an old site into a DDBS when the site recovers from failure. Site backup is the problem of creating a static backup copy of a database for archival or query purposes. We present an algorithm that solves the site initialization problem. By modifying the algorithm slightly, we get solutions to the other two problems as well. Our algorithm exploits the fact that a correct DDBS must run a serializable concurrency control algorithm. Our algorithm relies on the concurrency control algorithm to handle all inter-site synchronization

42 CFR 476.96 - Review period and reopening of initial denial determinations and changes as a result of DRG...

Science.gov (United States)

2010-10-01

... determinations and changes as a result of DRG validations. 476.96 Section 476.96 Public Health CENTERS FOR... initial denial determinations and changes as a result of DRG validations. (a) General timeframe. A QIO or... initial denial determination or a change as a result of a DRG validation. (b) Extended timeframes. (1) An...

Application of Terahertz Radiation to Soil Measurements: Initial Results

Science.gov (United States)

Dworak, Volker; Augustin, Sven; Gebbers, Robin

2011-01-01

Developing soil sensors with the possibility of continuous online measurement is a major challenge in soil science. Terahertz (THz) electromagnetic radiation may provide the opportunity for the measurement of organic material density, water content and other soil parameters at different soil depths. Penetration depth and information content is important for a functional soil sensor. Therefore, we present initial research on the analysis of absorption coefficients of four different soil samples by means of THz transmission measurements. An optimized soil sample holder to determine absorption coefficients was used. This setup improves data acquisition because interface reflections can be neglected. Frequencies of 340 GHz to 360 GHz and 1.627 THz to 2.523 THz provided information about an existing frequency dependency. The results demonstrate the potential of this THz approach for both soil analysis and imaging of buried objects. Therefore, the THz approach allows different soil samples to be distinguished according to their different absorption properties so that relations among soil parameters may be established in future. PMID:22163737

Initial results from the fast imaging solar spectrograph (FISS)

CERN Document Server

2015-01-01

This collection of papers describes the instrument and initial results obtained from the Fast Imaging Solar Spectrograph (FISS),  one of the post-focus instruments of the 1.6 meter New Solar Telescope at the Big Bear Solar Observatory. The FISS primarily aims at investigating structures and dynamics of  chromospheric features. This instrument is a dual-band Echelle spectrograph optimized for the simultaneous recording of the H I 656.3 nm band and the Ca II 854.2 nm band. The imaging is done with the fast raster scan realized by the linear motion of a two-mirror scanner, and its quality is determined by the performance of the adaptive optics of the telescope.    These papers illustrate the capability of the early FISS observations in the study of chromospheric features. Since the imaging quality has been improved a lot with the advance of the adaptive optics, one can obtain much better data with the current FISS observations.        This volume is aimed at graduate students and researchers working in...

Results from the Coded Aperture Neutron Imaging System (CANIS)

International Nuclear Information System (INIS)

Brubaker, Erik; Steele, John T.; Brennan, James S.; Hilton, Nathan R.; Marleau, Peter

2010-01-01

Because of their penetrating power, energetic neutrons and gamma rays (∼1 MeV) offer the best possibility of detecting highly shielded or distant special nuclear material (SNM). Of these, fast neutrons offer the greatest advantage due to their very low and well understood natural background. We are investigating a new approach to fast-neutron imaging- a coded aperture neutron imaging system (CANIS). Coded aperture neutron imaging should offer a highly efficient solution for improved detection speed, range, and sensitivity. We have demonstrated fast neutron and gamma ray imaging with several different configurations of coded masks patterns and detectors including an 'active' mask that is composed of neutron detectors. Here we describe our prototype detector and present some initial results from laboratory tests and demonstrations.

Towards a GME ensemble forecasting system: Ensemble initialization using the breeding technique

Directory of Open Access Journals (Sweden)

Jan D. Keller

2008-12-01

Full Text Available The quantitative forecast of precipitation requires a probabilistic background particularly with regard to forecast lead times of more than 3 days. As only ensemble simulations can provide useful information of the underlying probability density function, we built a new ensemble forecasting system (GME-EFS based on the GME model of the German Meteorological Service (DWD. For the generation of appropriate initial ensemble perturbations we chose the breeding technique developed by Toth and Kalnay (1993, 1997, which develops perturbations by estimating the regions of largest model error induced uncertainty. This method is applied and tested in the framework of quasi-operational forecasts for a three month period in 2007. The performance of the resulting ensemble forecasts are compared to the operational ensemble prediction systems ECMWF EPS and NCEP GFS by means of ensemble spread of free atmosphere parameters (geopotential and temperature and ensemble skill of precipitation forecasting. This comparison indicates that the GME ensemble forecasting system (GME-EFS provides reasonable forecasts with spread skill score comparable to that of the NCEP GFS. An analysis with the continuous ranked probability score exhibits a lack of resolution for the GME forecasts compared to the operational ensembles. However, with significant enhancements during the 3 month test period, the first results of our work with the GME-EFS indicate possibilities for further development as well as the potential for later operational usage.

Initiator Systems Effect on Particle Coagulation and Particle Size Distribution in One-Step Emulsion Polymerization of Styrene

Directory of Open Access Journals (Sweden)

Baijun Liu

2016-02-01

Full Text Available Particle coagulation is a facile approach to produce large-scale polymer latex particles. This approach has been widely used in academic and industrial research owing to its higher polymerization rate and one-step polymerization process. Our work was motivated to control the extent (or time of particle coagulation. Depending on reaction parameters, particle coagulation is also able to produce narrowly dispersed latex particles. In this study, a series of experiments were performed to investigate the role of the initiator system in determining particle coagulation and particle size distribution. Under the optimal initiation conditions, such as cationic initiator systems or higher reaction temperature, the time of particle coagulation would be advanced to particle nucleation period, leading to the narrowly dispersed polymer latex particles. By using a combination of the Smoluchowski equation and the electrostatic stability theory, the relationship between the particle size distribution and particle coagulation was established: the earlier the particle coagulation, the narrower the particle size distribution, while the larger the extent of particle coagulation, the larger the average particle size. Combined with the results of previous studies, a systematic method controlling the particle size distribution in the presence of particle coagulation was developed.

Threshold amounts of organic carbon needed to initiate reductive dechlorination in groundwater systems

Science.gov (United States)

Chapelle, Francis H.; Thomas, Lashun K.; Bradley, Paul M.; Rectanus, Heather V.; Widdowson, Mark A.

2012-01-01

Aquifer sediment and groundwater chemistry data from 15 Department of Defense facilities located throughout the United States were collected and analyzed with the goal of estimating the amount of natural organic carbon needed to initiate reductive dechlorination in groundwater systems. Aquifer sediments were analyzed for hydroxylamine and NaOH-extractable organic carbon, yielding a probable underestimate of potentially bioavailable organic carbon (PBOC). Aquifer sediments were also analyzed for total organic carbon (TOC) using an elemental combustion analyzer, yielding a probable overestimate of bioavailable carbon. Concentrations of PBOC correlated linearly with TOC with a slope near one. However, concentrations of PBOC were consistently five to ten times lower than TOC. When mean concentrations of dissolved oxygen observed at each site were plotted versus PBOC, it showed that anoxic conditions were initiated at approximately 200 mg/kg of PBOC. Similarly, the accumulation of reductive dechlorination daughter products relative to parent compounds increased at a PBOC concentration of approximately 200 mg/kg. Concentrations of total hydrolysable amino acids (THAA) in sediments also increased at approximately 200 mg/kg, and bioassays showed that sediment CO2 production correlated positively with THAA. The results of this study provide an estimate for threshold amounts of bioavailable carbon present in aquifer sediments (approximately 200 mg/kg of PBOC; approximately 1,000 to 2,000 mg/kg of TOC) needed to support reductive dechlorination in groundwater systems.

Initial Experience with the Machine Protection System for LHC

CERN Document Server

Schmidt, Ruediger; Dehning, Bernd; Ferro-Luzzi, Massimiliano; Goddard, Brennan; Lamont, Mike; Siemko, Andrzej; Uythoven, Jan; Wenninger, Jorg; Zerlauth, Markus

2010-01-01

For nominal beam parameters at 7 TeV/c each proton beam with a stored energy of 362 MJ threatens to damage accelerator equipment in case of uncontrolled beam loss. These parameters will only be reached after some years of operation, however, a small fraction of this energy is already sufficient to damage accelerator equipment or experiments. The correct functioning of the machine protection systems is vital during the different operational phases already for initial operation. When operating the complex magnet system, with and without beam, safe operation relies on the protection and interlock systems for the superconducting circuits. For safe injection and transfer of the beams from SPS to LHC, transfer line parameters are monitored, beam absorbers must be in the correct position and the LHC must be ready to accept beam. At the end of a fill and in case of failures beams must be properly extracted onto the dump blocks, for some types of failure within less than few hundred microseconds. Safe operation requir...

48 CFR 32.503-3 - Initiation of progress payments and review of accounting system.

Science.gov (United States)

2010-10-01

... payments and review of accounting system. 32.503-3 Section 32.503-3 Federal Acquisition Regulations System... on Costs 32.503-3 Initiation of progress payments and review of accounting system. (a) For... review (within the last 12 months) to be (1) reliable, competent, and capable of satisfactory performance...

Workshop for coordinating South Carolina`s pre-college systemic initiatives

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-26

The goal of the South Carolina Statewide Systemic Initiative (SC SSI) is to provide quality and effective learning experiences in science and mathematics to all people of South Carolina by affecting systemic change. To accomplish this goal, South Carolina must: (1) coordinate actions among many partners for science and mathematics change; (2) place the instruments of change into the hands of the effectors of change - teachers and schools; and (3) galvanize the support of policy makers, parents, and local communities for change. The SC SSI proposes to establish a network of 13 regional mathematics and science HUBs. The central idea of this plan is the accumulation of Teacher Leaders at each HUB who are prepared in special Curriculum Leadership Institutes to assist other teachers and schools. The HUB becomes a regional nexus for delivering services to schools who request assistance by matching schools with Teacher Leaders. Other initiatives such as the use of new student performance assessments, the integration of instructional technologies into the curriculum, a pilot preservice program, and Family Math and Family Science will be bundled together through the Teacher Leaders in the HUBs. Concurrent policy changes at the state level in teacher and administrator certification and recertification requirements, school regulations and accountability, and the student performance assessment system will enable teachers and schools to support instructional practices that model South Carolina`s new state Curriculum Frameworks in Mathematics and Science.

Preventive maintenance optimization for a stochastically degrading system with a random initial age

International Nuclear Information System (INIS)

Sidibe, I.B.; Khatab, A.; Diallo, C.; Kassambara, A.

2017-01-01

This paper investigates the optimal age replacement policy for used systems, such as second-hand products, which start their second life-cycle in a more severe environment with an initial age that is uncertain. This uncertain age is modelled as a random variable following continuous probability distributions. A mathematical model is developed to minimize the total expected cost per unit of time for these systems on an infinite time horizon. Optimality and existence conditions for a unique optimal solution are derived and used in a numerical procedure to solve the problem. Numerical experiments are provided to demonstrate the added value and the impacts of the random initial age on the optimal replacement policy.

Initial Results of Optical Vortex Laser Absorption Spectroscopy in the HYPER-I Device

Science.gov (United States)

Yoshimura, Shinji; Asai, Shoma; Aramaki, Mitsutoshi; Terasaka, Kenichiro; Ozawa, Naoya; Tanaka, Masayoshi; Morisaki, Tomohiro

2015-11-01

Optical vortex beams have a potential to make a new Doppler measurement, because not only parallel but perpendicular movement of atoms against the beam axis causes the Doppler shift of their resonant absorption frequency. As the first step of a proof-of-principle experiment, we have performed the optical vortex laser absorption spectroscopy for metastable argon neutrals in an ECR plasma produced in the HYPER-I device at the National Institute for Fusion Science, Japan. An external cavity diode laser (TOPTICA, DL100) of which center wavelength was 696.735 nm in vacuum was used for the light source. The Hermite-Gaussian (HG) beam was converted into the Laguerre-Gaussian (LG) beam (optical vortex) by a computer-generated hologram displayed on the spatial light modulator (Hamamatsu, LCOS-SLM X10468-07). In order to make fast neutral flow across the LG beam, a high speed solenoid valve system was installed on the HYPER-I device. Initial results including the comparison of absorption spectra for HG and LG beams will be presented. This study was supported by NINS young scientists collaboration program for cross-disciplinary study, NIFS collaboration research program (NIFS13KOAP026), and JSPS KAKENHI grant number 15K05365.

42 CFR 476.93 - Opportunity to discuss proposed initial denial determination and changes as a result of a DRG...

Science.gov (United States)

2010-10-01

... determination and changes as a result of a DRG validation. 476.93 Section 476.93 Public Health CENTERS FOR... initial denial determination and changes as a result of a DRG validation. Before a QIO reaches an initial denial determination or makes a change as a result of a DRG validation, it must— (a) Promptly notify the...

75 FR 17700 - Energy Efficient Building Systems Regional Innovation Cluster Initiative-Joint Federal Funding...

Science.gov (United States)

2010-04-07

... economically dynamic regional innovation cluster focused on energy efficient buildings technologies and systems...-risk, high-reward research that overcomes technology challenges through approaches that span basic... DEPARTMENT OF ENERGY Energy Efficient Building Systems Regional Innovation Cluster Initiative...

The Initial Conditions of Fractional Calculus

International Nuclear Information System (INIS)

Trigeassou, J. C.; Maamri, N.

2011-01-01

During the past fifty years , Fractional Calculus has become an original and renowned mathematical tool for the modelling of diffusion Partial Differential Equations and the design of robust control algorithms. However, in spite of these celebrated results, some theoretical problems have not yet received a satisfying solution. The mastery of initial conditions, either for Fractional Differential Equations (FDEs) or for the Caputo and Riemann-Liouville fractional derivatives, remains an open research domain. The solution of this fundamental problem, also related to the long range memory property, is certainly the necessary prerequisite for a satisfying approach to modelling and control applications. The fractional integrator and its continuously frequency distributed differential model is a valuable tool for the simulation of fractional systems and the solution of initial condition problems. Indeed, the infinite dimensional state vector of fractional integrators allows the direct generalization to fractional calculus of the theoretical results of integer order systems. After a reminder of definitions and properties related to fractional derivatives and systems, this presentation is intended to show, based on the results of two recent publications [1,2], how the fractional integrator provides the solution of the initial condition problem of FDEs and of Caputo and Riemann-Liouville fractional derivatives. Numerical simulation examples illustrate and validate these new theoretical concepts.

Programmed initiation of hemodialysis for systemic amyloidosis patients associated with rheumatoid arthritis.

Science.gov (United States)

Kuroda, Takeshi; Tanabe, Naohito; Kobayashi, Daisuke; Sato, Hiroe; Wada, Yoko; Murakami, Shuichi; Sakatsume, Minoru; Nakano, Masaaki; Narita, Ichiei

2011-09-01

Reactive amyloidosis is a serious systemic disease in rheumatoid arthritis (RA). Amyloid protein can be deposited in kidneys, heart or gastrointestinal tract leading to organ failure. Renal involvement is a well-known complication in amyloidosis as this may culminate in end-stage renal disease (ESRD). Hemodialysis (HD) is always considered the treatment of choice for such patients; however, the prognosis is usually poor due to a large number of sudden deaths immediately following HD therapy. To circumvent the problem of HD initiation while instituting HD safety, we devised a plan to start HD and compare patient's survival with our previous data. Sixty-three patients were treated with HD. They were categorized according to the initiation of first dialysis. All patients were divided into planned, unplanned and programmed initiation groups. First dialysis that had been initiated as not urgent was considered 'planned' (20 patients). First dialysis that had been performed urgently for life-threatening renal insufficiency was considered 'unplanned' (31 patients). First dialysis that had been initiated as not urgent and according to our dialysis program was considered 'programmed' (12 patients). Survival of these 63 patients from the initiation of HD at 38 days was 75%, at 321 days was 50% and at 1,784 days was 25%. Patients with unplanned initiation of HD showed a significant poor survival compared with those of both planned and programmed initiation. Additionally, patients with planned and programmed initiation of HD showed no significant difference for the patients' survival. Our study demonstrates that patients with amyloidosis have a higher mortality rate. Nevertheless, programmed initiation of HD will improve the prognosis of patients with ESRD. Such possibility needs to be considered in more detail in the future.

Readiness to adopt a performance measurement system for substance abuse treatment: Findings from the Service Quality Measures initiative

Directory of Open Access Journals (Sweden)

B Myers

2017-02-01

Full Text Available Background. A performance measurement system – the Service Quality Measures (SQM initiative – has been developed to monitor the quality of South Africa (SA’s substance abuse treatment services. Identifying factors associated with readiness to adopt this system may inform strategies to facilitate its robust implementation. Objective. To examine factors associated with readiness to adopt a performance measurement system among SA substance abuse treatment providers. Methods. We surveyed 81 treatment providers from 13 treatment sites in the Western Cape, SA. The survey examined awareness, resources, organisational climate, leadership support and readiness to adopt the SQM system. Regression analysis was used to identify factors associated with readiness to adopt this system. Results. Readiness to adopt the SQM initiative was high (M=5.64, standard deviation 1.63. In bivariate analyses, caseload size (F=3.73 (degrees of freedom (df=3.70, p=0.015, awareness (r=0.78, p<0.0001, leadership support (r=0.70, p<0.0001, resources (r=0.65, p<0.0001, openness to change (r=0.372, p=0.001, and external pressure to change were associated with readiness to adopt the SQM. In multivariate analyses, only awareness of the SQM initiative (B=0.34, standard error (SE 0.08, t=4.4, p<0.0001 and leadership support (B=0.45, SE 0.11, t=4.0, p<0.0001 were significantly associated with readiness to adopt this system. Conclusion. While treatment providers report high levels of readiness to adopt the SQM system, findings show that the likelihood of adoption can be further increased through improved provider awareness and enhanced leadership support for this health innovation.

DYNAMIC STABILITY OF THE SOLAR SYSTEM: STATISTICALLY INCONCLUSIVE RESULTS FROM ENSEMBLE INTEGRATIONS

Energy Technology Data Exchange (ETDEWEB)

Zeebe, Richard E., E-mail: zeebe@soest.hawaii.edu [School of Ocean and Earth Science and Technology, University of Hawaii at Manoa, 1000 Pope Road, MSB 629, Honolulu, HI 96822 (United States)

2015-01-01

Due to the chaotic nature of the solar system, the question of its long-term stability can only be answered in a statistical sense, for instance, based on numerical ensemble integrations of nearby orbits. Destabilization of the inner planets, leading to close encounters and/or collisions can be initiated through a large increase in Mercury's eccentricity, with a currently assumed likelihood of ∼1%. However, little is known at present about the robustness of this number. Here I report ensemble integrations of the full equations of motion of the eight planets and Pluto over 5 Gyr, including contributions from general relativity. The results show that different numerical algorithms lead to statistically different results for the evolution of Mercury's eccentricity (e{sub M}). For instance, starting at present initial conditions (e{sub M}≃0.21), Mercury's maximum eccentricity achieved over 5 Gyr is, on average, significantly higher in symplectic ensemble integrations using heliocentric rather than Jacobi coordinates and stricter error control. In contrast, starting at a possible future configuration (e{sub M}≃0.53), Mercury's maximum eccentricity achieved over the subsequent 500 Myr is, on average, significantly lower using heliocentric rather than Jacobi coordinates. For example, the probability for e{sub M} to increase beyond 0.53 over 500 Myr is >90% (Jacobi) versus only 40%-55% (heliocentric). This poses a dilemma because the physical evolution of the real system—and its probabilistic behavior—cannot depend on the coordinate system or the numerical algorithm chosen to describe it. Some tests of the numerical algorithms suggest that symplectic integrators using heliocentric coordinates underestimate the odds for destabilization of Mercury's orbit at high initial e{sub M}.

SPECIAL ASPECTS OF INITIAL OPTICAL SCHEME SELECTION FOR DESIGN OF NON-IMAGING OPTICAL SYSTEMS

Directory of Open Access Journals (Sweden)

R. V. Anitropov

2016-01-01

Full Text Available Subject of Research. The research results, structural composition analysis and the parametric synthesis of the projected imaging and non-imaging optical systems were presented. We made an attempt to use the gained experience about imaging systems while designing non-imaging systems, by adapting the composition theory for the calculations of non-imaging systems. Several patterns were revealed, which provide a deeper understanding of the design process of non-imaging optical systems; measures of its optimization were proposed. Method. We investigated the applicability of the theory of composition and synthesis of non-imaging optical systems. The main provisions of the theory of composition are based on the division of all available optical elements in four types depending on their functionality, which corresponds to a modular design. Similar items were identified in non-imaging optical systems and adaptation of composition theory to their design became possible. Main Results. General design patterns of imaging and non-imaging optical systems were studied. Classification of systems, components, as well as technical and generic characteristics of imaging and non-imaging optical systems was determined. Search mechanism of the initial optical system by means of structural and parametric synthesis of non-imaging optical system was formalized. The basic elements were determined included in non-imaging systems and their classification by functionality was done. They were subdivided into basic, corrective, wide angle and high aperture ones. The rules for formation of these elements and their composition were determined: surface reflecting, refracting, spherical and nonspherical elements with total internal reflection. The foundations of composition theory for non-imaging optical systems were laid. The approbation of this method was carried out on the example of the illumination system calculation for surgical room. A 3D model of an illumination optical

Initial results for a 170 GHz high power ITER waveguide component test stand

Science.gov (United States)

Bigelow, Timothy; Barker, Alan; Dukes, Carl; Killough, Stephen; Kaufman, Michael; White, John; Bell, Gary; Hanson, Greg; Rasmussen, Dave

2014-10-01

A high power microwave test stand is being setup at ORNL to enable prototype testing of 170 GHz cw waveguide components being developed for the ITER ECH system. The ITER ECH system will utilize 63.5 mm diameter evacuated corrugated waveguide and will have 24 >150 m long runs. A 170 GHz 1 MW class gyrotron is being developed by Communications and Power Industries and is nearing completion. A HVDC power supply, water-cooling and control system has been partially tested in preparation for arrival of the gyrotron. The power supply and water-cooling system are being designed to operate for >3600 second pulses to simulate the operating conditions planned for the ITER ECH system. The gyrotron Gaussian beam output has a single mirror for focusing into a 63.5 mm corrugated waveguide in the vertical plane. The output beam and mirror are enclosed in an evacuated duct with absorber for stray radiation. Beam alignment with the waveguide is a critical task so a combination of mirror tilt adjustments and a bellows for offsets will be provided. Analysis of thermal patterns on thin witness plates will provide gyrotron mode purity and waveguide coupling efficiency data. Pre-prototype waveguide components and two dummy loads are available for initial operational testing of the gyrotron. ORNL is managed by UT-Battelle, LLC, for the U.S. Dept. of Energy under Contract DE-AC-05-00OR22725.

Performance Evaluation of Orbit Determination System during Initial Phase of INSAT-3 Mission

Science.gov (United States)

Subramanian, B.; Vighnesam, N. V.

INSAT-3C is the second in the third generation of ISRO's INSAT series of satellites that was launched by ARIANE-SPACE on 23 January 2002 at 23 h 46 m 57 s (lift off time in U.T). The ARIANE-4 Flight Nr.147 took off from Kourou in French Guyana and injected the 2750-kg communications satellite in a geostationary transfer orbit of (571 X 35935) km with an inclination of 4.007 deg at 00 h 07 m 48 s U.T on 24 January 2002 (1252 s after lift off). The satellite was successfully guided into its intended geostationary position of 74 deg E longitude by 09 February 2002 after a series of four firings of its Liquid Apogee Motor (LAM) and four station acquisition (STAQ) maneuvers. Six distinct phases of the mission were categorized based on the orbit characteristics of the INSAT- 3C mission, namely, the pre-launch phase, the launch phase, transfer orbit phase, intermediate orbit phase, drift orbit phase and synchronous orbit phase. The orbit with a perigee height of 571 km at injection of the satellite, was gradually raised to higher orbits with perigee height increasing to 9346 km after Apogee Motor Firing #1 (AMF #1), 18335 km after AMF #2, 32448 km after AMF #3 and 35493 km after AMF #4. The North and South solar panels and the reflectors were deployed at this stage of the mission and the attitude of the satellite with respect to the three axes was stabilized. The Orbit Determination System (ODS) that was used in the initial phase of the mission played a crucial role in realizing the objectives of the mission. This system which consisted of Tracking Data Pre-Processing (TDPP) software, Ephemeris Generation (EPHGEN) software and the Orbit Determination (OD) software, performed rigorously and its results were used for planning the AMF and STAQ strategies with a greater degree of accuracy. This paper reports the results of evaluation of the performance of the apogee-motor firings employed to place the satellite in its intended position where it is collocated with INSAT-1D

Non-lethal heat treatment of cells results in reduction of tumor initiation and metastatic potential

International Nuclear Information System (INIS)

Kim, Yoo-Shin; Lee, Tae Hoon; O'Neill, Brian E.

2015-01-01

Non-lethal hyperthermia is used clinically as adjuvant treatment to radiation, with mixed results. Denaturation of protein during hyperthermia treatment is expected to synergize with radiation damage to cause cell cycle arrest and apoptosis. Alternatively, hyperthermia is known to cause tissue level changes in blood flow, increasing the oxygenation and radiosensitivity of often hypoxic tumors. In this study, we elucidate a third possibility, that hyperthermia alters cellular adhesion and mechanotransduction, with particular impact on the cancer stem cell population. We demonstrate that cell heating results in a robust but temporary loss of cancer cell aggressiveness and metastatic potential in mouse models. In vitro, this heating results in a temporary loss in cell mobility, adhesion, and proliferation. Our hypothesis is that the loss of cellular adhesion results in suppression of cancer stem cells and loss of tumor virulence and metastatic potential. Our study suggests that the metastatic potential of cancer is particularly reduced by the effects of heat on cellular adhesion and mechanotransduction. If true, this could help explain both the successes and failures of clinical hyperthermia, and suggest ways to target treatments to those who would most benefit. - Highlights: • Non-lethal hyperthermia treatment of cancer cells is shown to cause a reduction in rates of tumor initiation and metastasis. • Dynamic imaging of cells during heat treatment shows temporary changes in cell shape, cell migration, and cell proliferation. • Loss of adhesion may lead to the observed effect, which may disproportionately impact the tumor initiating cell fraction. • Loss or suppression of the tumor initiating cell fraction results in the observed loss of metastatic potential in vivo. • This result may lead to new approaches to synergizing hyperthermia with surgery, radiation, and chemotherapy

Non-lethal heat treatment of cells results in reduction of tumor initiation and metastatic potential

Energy Technology Data Exchange (ETDEWEB)

Kim, Yoo-Shin; Lee, Tae Hoon; O' Neill, Brian E., E-mail: BEOneill@houstonmethodist.org

2015-08-14

Non-lethal hyperthermia is used clinically as adjuvant treatment to radiation, with mixed results. Denaturation of protein during hyperthermia treatment is expected to synergize with radiation damage to cause cell cycle arrest and apoptosis. Alternatively, hyperthermia is known to cause tissue level changes in blood flow, increasing the oxygenation and radiosensitivity of often hypoxic tumors. In this study, we elucidate a third possibility, that hyperthermia alters cellular adhesion and mechanotransduction, with particular impact on the cancer stem cell population. We demonstrate that cell heating results in a robust but temporary loss of cancer cell aggressiveness and metastatic potential in mouse models. In vitro, this heating results in a temporary loss in cell mobility, adhesion, and proliferation. Our hypothesis is that the loss of cellular adhesion results in suppression of cancer stem cells and loss of tumor virulence and metastatic potential. Our study suggests that the metastatic potential of cancer is particularly reduced by the effects of heat on cellular adhesion and mechanotransduction. If true, this could help explain both the successes and failures of clinical hyperthermia, and suggest ways to target treatments to those who would most benefit. - Highlights: • Non-lethal hyperthermia treatment of cancer cells is shown to cause a reduction in rates of tumor initiation and metastasis. • Dynamic imaging of cells during heat treatment shows temporary changes in cell shape, cell migration, and cell proliferation. • Loss of adhesion may lead to the observed effect, which may disproportionately impact the tumor initiating cell fraction. • Loss or suppression of the tumor initiating cell fraction results in the observed loss of metastatic potential in vivo. • This result may lead to new approaches to synergizing hyperthermia with surgery, radiation, and chemotherapy.

Initial computer modeling of WIPP [Waste Isolation Pilot Plant] underground ventilation system, September 1985--March 1986

International Nuclear Information System (INIS)

Sethi, S.

1986-11-01

Provision of a good ventilation system has been and continues to be a major priority here of those responsible for its design, management, and operation. As an ongoing effort in this direction, development of computer simulated models for the system was initiated in September, 1985. It was decided to utilize Dravo's 'MINEVENT' computer program for this purpose. Accordingly, initial computer models of the mine's ventilation system have been developed for various modes of operation. Specifically, they include: Simulation of the current ventilation system, and Simulation of the designed ventilation system for modes: mine construction mode/shift, waste storage mode/shift, and air reversal mode. 5 figs

Initial Results from Coaxial Helicity Injection Experiments in NSTX

International Nuclear Information System (INIS)

Raman, R.; Jarboe, T.R.; Mueller, D.; Schaffer, M.J.; Maqueda, R.; Nelson, B.A.; Sabbagh, S.; Bell, M.; Ewig, R.; Fredrickson, E.; Gates, D.; Hosea, J.; Ji, H.; Kaita, R.; Kaye, S.M.; Kugel, H.; Maingi, R.; Menard, J.; Ono, M.; Orvis, D.; Paolette, F.; Paul, S.; Peng, M.; Skinner, C.H.; Wilgen, W.; Zweben, S.

2001-01-01

Coaxial Helicity Injection (CHI) has been investigated on the National Spherical Torus Experiment (NSTX). Initial experiments produced 130 kA of toroidal current without the use of the central solenoid. The corresponding injector current was 20 kA. Discharges with pulse lengths up to 130 ms have been produced

Control of adverse effects of explosive blasting in mines by using shock tube (non-electric) initiation systems and its future challenges

Energy Technology Data Exchange (ETDEWEB)

Sharma, P.D. [Maharashtra Explosives Ltd., Nagpur (India)

2000-04-01

Every kind of blasting in mines produces some adverse effects on environment, such as ground vibration, noise, fly rock etc. Presently, for restricting these adverse effects, use of shock tube (non-electric) initiation systems are gaining momentum. There are some inherent shortcomings of this initiation system regarding chances of misfires. This paper discusses the various adverse effects of blasting, advantages of shock tube initiation system and the shortcomings of shock tube initiation system regarding chances of misfire and how misfire arises out of failure of shock tube initiation system is different and more dangerous than the misfire occurring due to failure of conventional system (with detonating fuse and cord relays). 1 tab.

Turbulence modeling with fractional derivatives: Derivation from first principles and initial results

Science.gov (United States)

Epps, Brenden; Cushman-Roisin, Benoit

2017-11-01

Fluid turbulence is an outstanding unsolved problem in classical physics, despite 120+ years of sustained effort. Given this history, we assert that a new mathematical framework is needed to make a transformative breakthrough. This talk offers one such framework, based upon kinetic theory tied to the statistics of turbulent transport. Starting from the Boltzmann equation and ``Lévy α-stable distributions'', we derive a turbulence model that expresses the turbulent stresses in the form of a fractional derivative, where the fractional order is tied to the transport behavior of the flow. Initial results are presented herein, for the cases of Couette-Poiseuille flow and 2D boundary layers. Among other results, our model is able to reproduce the logarithmic Law of the Wall in shear turbulence.

Prototype radiographic system for emergency and intensive care units: Initial experience

International Nuclear Information System (INIS)

Mirvis, S.

1986-01-01

A prototype radiographic system has been developed for use in bedside examinations in multibed trauma or intensive care units and emergency rooms. The system features a single-phase, high-frequency 30-kW ceiling-mounted generator with an x-ray tube extending from a long counterbalanced arm. All movements are servo-assisted for ease of operation. Based on initial experience, the unit allows easier access to the patient around resuscitation and monitoring equipment, occupies less floor space, and yields better quality images than do standard mobile radiographic units

Computational results for the control of a divergent N-echelon inventory system

NARCIS (Netherlands)

Diks, E.B.; Kok, de A.G.

1996-01-01

Consider a divergent multi-echelon inventory system, e.g., a distribution system or a production system. At every facility in the system orders are placed (or production is initiated) periodically. The order arrives after a fixed lead time. At the end of each period linear costs are incurred at each

42 CFR 476.94 - Notice of QIO initial denial determination and changes as a result of a DRG validation.

Science.gov (United States)

2010-10-01

... changes as a result of a DRG validation. 476.94 Section 476.94 Public Health CENTERS FOR MEDICARE... changes as a result of a DRG validation. (a) Notice of initial denial determination—(1) Parties to be... retrospective review, (excluding DRG validation and post procedure review), within 3 working days of the initial...

Initial testing of the tritium systems at the Tokamak Fusion Test Reactor

International Nuclear Information System (INIS)

Anderson, J.L.; Sissingh, R.A.P.; Gentile, C.A.; Rossmassler, R.L.; Walters, R.T.; Voorhees, D.R.

1993-01-01

The Tokamak Fusion Test Reactor (TFTR) at Princeton will start its D-T experiments in late 1993, introducing and operating the tokamak with tritium in order to begin the study of burning plasma physics in D-T. Trace tritium injection experiments, using small amounts of tritium will begin in the fall of 1993. In preparation for these experiments, a series of tests with low concentrations of tritium inn deuterium have been performed as an initial qualification of the tritium systems. These tests began in April 1993. This paper describes the initial testing of the equipment in the TFTR tritium facility

Condition Help: A Patient- and Family-Initiated Rapid Response System.

Science.gov (United States)

Eden, Elizabeth L; Rack, Laurie L; Chen, Ling-Wan; Bump, Gregory M

2017-03-01

Rapid response teams (RRTs) help in delivering safe, timely care. Typically they are activated by clinicians using specific parameters. Allowing patients and families to activate RRTs is a novel intervention. The University of Pittsburgh Medical Center developed and implemented a patient- and family-initiated rapid response system called Condition Help (CH). When the CH system is activated, a patient care liaison or an on-duty administrator meets bedside with the unit charge nurse to address the patient's concerns. In this study, we collected demographic data, call reasons, call designations (safety or nonsafety), and outcome information for all CH calls made during the period January 2012 through June 2015. Two hundred forty patients/family members made 367 CH calls during the study period. Most calls were made by patients (76.8%) rather than family members (21.8%). Of the 240 patients, 43 (18%) made multiple calls; their calls accounted for 46.3% of all calls (170/367). Inadequate pain control was the reason for the call in most cases (48.2%), followed by dissatisfaction with staff (12.5%). The majority of calls involved nonsafety issues (83.4%) rather than safety issues (11.4%). In 41.4% of cases, a change in care was made. Patient- and family-initiated RRTs are designed to engage patients and families in providing safer care. In the CH system, safety issues are identified, but the majority of calls involve nonsafety issues. Journal of Hospital Medicine 2017;12:157-161. © 2017 Society of Hospital Medicine

Initial results of Pakistan's first road traffic injury surveillance project.

Science.gov (United States)

Shamim, Shahzad; Razzak, Junaid A; Jooma, Rashid; Khan, Uzma

2011-09-01

Our aim is to report the findings of the initial three years of road traffic injuries (RTI) surveillance at Karachi and to compare it with previously published RTI-related data from Pakistan and other low-and middle-income countries. Data were collected through the RTI surveillance programme at Karachi (RTIRP) from the five biggest emergency departments of the city, which receive almost all the major emergencies of the city for the period September 2006 till September 2009. A total of 99,272 victims were enlisted by the RTIRP during the study period. Annual incidence of RTI is calculated to be 184.3 per 100,000 populations and mortality is 5.7 per 100,000 populations. Eighty nine per cent of victims are male and 73% are between 15 and 44 years of age. Commonest road user to be affected is riders of two wheelers (45%). Only 7% of affected motorcyclists were found to be wearing helmets at the time of the accident. Trends of injuries remained uniform over the years. Most frequent injuries were external wounds, followed by orthopaedic injuries. On the basis of our surveillance system, we have presented the largest RTI-related data from a metropolitan city of Pakistan to date.

A model-based initial guess for estimating parameters in systems of ordinary differential equations.

Science.gov (United States)

Dattner, Itai

2015-12-01

The inverse problem of parameter estimation from noisy observations is a major challenge in statistical inference for dynamical systems. Parameter estimation is usually carried out by optimizing some criterion function over the parameter space. Unless the optimization process starts with a good initial guess, the estimation may take an unreasonable amount of time, and may converge to local solutions, if at all. In this article, we introduce a novel technique for generating good initial guesses that can be used by any estimation method. We focus on the fairly general and often applied class of systems linear in the parameters. The new methodology bypasses numerical integration and can handle partially observed systems. We illustrate the performance of the method using simulations and apply it to real data. © 2015, The International Biometric Society.

Test results of HTTR control system

International Nuclear Information System (INIS)

Motegi, Toshihiro; Iigaki, Kazuhiko; Saito, Kenji; Sawahata, Hiroaki; Hirato, Yoji; Kondo, Makoto; Shibutani, Hideki; Ogawa, Satoru; Shinozaki, Masayuki; Mizushima, Toshihiko; Kawasaki, Kozo

2006-06-01

The plant control performance of the IHX helium flow rate control system, the PPWC helium flow rate control system, the secondary helium flow rate control system, the inlet temperature control system, the reactor power control system and the outlet temperature control system of the HTTR are obtained through function tests and power-up tests. As the test results, the control systems show stable control response under transient condition. Both of inlet temperature control system and reactor power control system shows stable operation from 30% to 100%, respectively. This report describes the outline of control systems and test results. (author)

Development and evaluation of a function-oriented display system: background and initial results

International Nuclear Information System (INIS)

Andresen, Gisle; Pirus, Dominique

2005-01-01

Screen-based Human System Interfaces (HSI) are gradually replacing the conventional panel-based HSls, although no clear design philosophy for screen-based HSIs exists. The current paper presents a comprehensive design philosophy where a function-analysis of the plant forms the backbone of the information requirements, information presentation and display organization. The main characteristics of the concept are described as well as the development process behind the first prototype. Findings from the first usability test of the prototype are reported and potential benefits of the HSI are discussed. The work is part of OECD Halden Reactor Project's ongoing research on innovative design for advanced NPP control-rooms and is conducted in close co-operation with Electricite de France

Tectonic evolution of the outer Izu-Bonin-Mariana fore arc system: initial results from IODP Expedition 352

Science.gov (United States)

Kurz, W.; Ferre, E. C.; Robertson, A. H. F.; Avery, A. J.; Kutterolf, S.

2015-12-01

During International Ocean Discovery Program (IODP) Expedition 352, a section through the volcanic stratigraphy of the outer fore arc of the Izu-Bonin-Mariana (IBM) system was drilled to trace magmatism, tectonics, and crustal accretion associated with subduction initiation. Structures within drill cores, borehole and site survey seismic data indicate that tectonic deformation in the outer IBM fore arc is mainly post-magmatic. Extension generated asymmetric sediment basins such as half-grabens at sites 352-U1439 and 352-U1442 on the upper trench slope. Along their eastern margins the basins are bounded by west-dipping normal faults. Deformation was localized along multiple sets of faults, accompanied by syn-tectonic pelagic and volcaniclastic sedimentation. The lowermost sedimentary units were tilted eastward by ~20°. Tilted beds were covered by sub-horizontal beds. Biostratigraphic constraints reveal a minimum age of the oldest sediments at ~ 35 Ma; timing of the sedimentary unconformities is between ~ 27 and 32 Ma. At sites 352-U1440 and 352-U1441 on the outer fore arc strike-slip faults are bounding sediment basins. Sediments were not significantly affected by tectonic tilting. Biostratigraphy gives a minimum age of the basement-cover contact between ~29.5 and 32 Ma. The post-magmatic structures reveal a multiphase tectonic evolution of the outer IBM fore arc. At sites 352-U1439 and 352-U1442, shear with dominant reverse to oblique reverse displacement was localized along subhorizontal fault zones, steep slickensides and shear fractures. These were either re-activated as or cut by normal-faults and strike-slip faults. Extension was also accommodated by steep to subvertical mineralized veins and extensional fractures. Faults at sites 352-U1440 and 352-U1441 show mainly strike-slip kinematics. Sediments overlying the igneous basement(maximum Late Eocene to Recent age), document ash and aeolian input, together with mass wasting of the fault-bounded sediment ponds.

Technological plasma source equipped with combined system of vacuum-arc discharge initiation

International Nuclear Information System (INIS)

Sysoev, Yu.O.

2013-01-01

The construction and the operation principle of erosion plasma source with a three-stage system of vacuum-arc discharge excitation is described. As first two step was used the modified contactless start system with plasma injector, which was widely used in standard plasma sources of the ''Bulat'' systems. The operation principle of the third stage was based on the transition of glow discharge to arc discharge. Coordinated operation of three stages during various stages of coating deposition provided significant increasing of service life and reliability of the system of vacuum-arc discharge initiation and extended the functionality of the plasma source

Optimal control of distributed parameter system with incomplete information about the initial condition

International Nuclear Information System (INIS)

Kotarski, W.; Kowalewski, A.

1982-03-01

In this paper we consider an optimal control problem for a system described by a linear partial differential equation of the parabolic type with Dirichlet's boundary condition. We impose some constraints on the control. The performance functional has the integral form. The control time T is fixed. The initial condition is not given by a known function but belongs to a certain set (incomplete information about the initial state). The problem formulated in this paper describes the process of optimal heating, of which we do not have exact information about the initial temperature on the heated object. We present an example in which the set of admissible controls and one of initial conditions are given by means of the norm constraints too. The application of the well-known projective gradient method in the Hilbert space allows us to obtain the numerical solution for our optimization problem. (author)

Interfacing systems loss of coolant accident (ISLOCA) pressure capacity methodology and Davis-Besse results

International Nuclear Information System (INIS)

Wesley, D.A.

1991-01-01

A loss of coolant accident resulting from the overpressurization by reactor coolant fluid of a system designed for low-pressure, low-temperature service has been identified as a potential contributor to nuclear power plant risk. In this paper, the methodology developed to assess the probability of failure as a function of internal pressure is presented, and sample results developed for the controlling failure modes and locations of four fluid systems at the Davis-Besse Plant are shown. Included in this evaluation are the tanks, heat exchangers, filters, pumps, valves, and flanged connections for each system. The variability in the probability of failure is included, and the estimated leak rates or leak areas are given for the controlling modes of failure. For this evaluation, all failures are based on quasistatic pressures since the probability of dynamic effects resulting from such causes as water hammer have been initially judged to be negligible for the Davis-Besse plant ISLOCA

Toyota production system quality improvement initiative improves perioperative antibiotic therapy.

Science.gov (United States)

Burkitt, Kelly H; Mor, Maria K; Jain, Rajiv; Kruszewski, Matthew S; McCray, Ellesha E; Moreland, Michael E; Muder, Robert R; Obrosky, David Scott; Sevick, Mary Ann; Wilson, Mark A; Fine, Michael J

2009-09-01

To assess the role of a Toyota production system (TPS) quality improvement (QI) intervention on appropriateness of perioperative antibiotic therapy and in length of hospital stay (LOS) among surgical patients. Pre-post quasi-experimental study using local and national retrospective cohorts. We used TPS methods to implement a multifaceted intervention to reduce nosocomial methicillin-resistant Staphylococcus aureus infections on a Veterans Affairs surgical unit, which led to a QI intervention targeting appropriate perioperative antibiotic prophylaxis. Appropriate perioperative antibiotic therapy was defined as selection of the recommended antibiotic agents for a duration not exceeding 24 hours from the time of the operation. The local computerized medical record system was used to identify patients undergoing the 25 most common surgical procedures and to examine changes in appropriate antibiotic therapy and LOS over time. Overall, 2550 surgical admissions were identified from the local computerized medical records. The proportion of surgical admissions receiving appropriate perioperative antibiotics was significantly higher (P <.01) in 2004 after initiation of the TPS intervention (44.0%) compared with the previous 4 years (range, 23.4%-29.8%) primarily because of improvements in compliance with antibiotic therapy duration rather than appropriate antibiotic selection. There was no statistically significant decrease in LOS over time. The use of TPS methods resulted in a QI intervention that was associated with an increase in appropriate perioperative antibiotic therapy among surgical patients, without affecting LOS.

Wayfinding the Live 5-2-1-0 Initiative-At the Intersection between Systems Thinking and Community-Based Childhood Obesity Prevention.

Science.gov (United States)

Amed, Shazhan; Shea, Stephanie; Pinkney, Susan; Wharf Higgins, Joan; Naylor, Patti-Jean

2016-06-21

Childhood obesity is complex and requires a 'systems approach' that collectively engages across multiple community settings. Sustainable Childhood Obesity Prevention through Community Engagement (SCOPE) has implemented Live 5-2-1-0-a multi-sector, multi-component childhood obesity prevention initiative informed by systems thinking and participatory research via an innovative knowledge translation (KT) model (RE-FRAME). This paper describes the protocol for implementing and evaluating RE-FRAME in two 'existing' (>2 years of implementation) and two 'new' Live 5-2-1-0 communities to understand how to facilitate and sustain systems/community-level change. In this mixed-methods study, RE-FRAME was implemented via online resources, webinars, a backbone organization (SCOPE) coordinating the initiative, and a linking system supporting KT. Qualitative and quantitative data were collected using surveys and stakeholder interviews, analyzed using thematic analysis and descriptive statistics, respectively. Existing communities described the consistency of Live 5-2-1-0 and extensive local partnerships/champions as catalysts for synergistic community-wide action; new communities felt that the simplicity of the message combined with the transfer of experiential learning would inform their own strategies and policies/programs to broadly disseminate Live 5-2-1-0. RE-FRAME effectively guided the refinement of the initiative and provided a framework upon which evaluation results described how to implement a community-based systems approach to childhood obesity prevention.

Project Execution Plan for Project W-211 Initial Tank Retrieval Systems (ITRS)

International Nuclear Information System (INIS)

VAN BEEK, J.E.

2000-01-01

This Project Execution Plan documents the methodology for managing Project W-211. Project W-211, Initial Tank Retrieval Systems (ITRS), is a fiscal year 1994 Major Systems Acquisition that will provide systems for retrieval of radioactive wastes from selected double-shell tanks (DST). The contents of these tanks are a combination of supernatant liquids and settled solids. To retrieve waste from the tanks, it is first necessary to mix the liquid and solids prior to transferring the slurry to alternative storage or treatment facilities. The ITRS will provide systems to mobilize the settled solids and transfer the wastes out of the tanks. In so doing, ITRS provides feed for the future waste treatment plant, allows for consolidation of tank solids to manage space within existing DST storage capacity, and supports continued safe storage of tank waste. The ITRS scope has been revised to include waste retrieval systems for tanks AP-102, AP-104, AN-102, AN-103, AN-104, AN-105, AY-102, AZ-102, and SY-102. This current tank selection and sequence provides retrieval systems supporting the River Protection Project (RF'P) Waste Treatment Facility and sustains the ability to provide final remediation of several watch list DSTs via treatment. The ITRS is configured to support changing program needs, as constrained by available budget, by maintaining the flexibility for exchanging tanks requiring mixer pump-based retrieval systems and shifting the retrieval sequence. Preliminary design was configured such that an adequate basis exists for initiating Title II design of a mixer pump-based retrieval system for any DST. This Project Execution Plan (PEP), derived from the predecessor Project Management Plan, documents the methodology for managing the ITRS, formalizes organizational responsibilities and interfaces, and identifies project requirements such as change control, design verification, systems engineering, and human factors engineering

Entry, Descent and Landing Systems Analysis: Exploration Class Simulation Overview and Results

Science.gov (United States)

DwyerCianciolo, Alicia M.; Davis, Jody L.; Shidner, Jeremy D.; Powell, Richard W.

2010-01-01

NASA senior management commissioned the Entry, Descent and Landing Systems Analysis (EDL-SA) Study in 2008 to identify and roadmap the Entry, Descent and Landing (EDL) technology investments that the agency needed to make in order to successfully land large payloads at Mars for both robotic and exploration or human-scale missions. The year one exploration class mission activity considered technologies capable of delivering a 40-mt payload. This paper provides an overview of the exploration class mission study, including technologies considered, models developed and initial simulation results from the EDL-SA year one effort.

Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) Project, UAS Control and Non-Payload Communication System Phase-1 Flight Test Results

Science.gov (United States)

Griner, James H.

2014-01-01

NASA's UAS Integration in the NAS project, has partnered with Rockwell Collins to develop a concept Control and Non-Payload Communication (CNPC) system prototype radio, operating on recently allocated UAS frequency spectrum bands. This prototype radio is being used to validate initial proposed performance requirements for UAS control communications. This presentation will give an overview of the current status of the prototype radio development, and results from phase 1 flight tests conducted during 2013.

New results on initial state & quarkonia with ATLAS

CERN Document Server

Tapia Araya, Sebastian; The ATLAS collaboration

2017-01-01

Weak bosons do not interact strongly with the dense and hot medium formed in the nuclear collisions, thus should be sensitive to the nuclear modification of parton distribution functions (nPDFs). The in-medium modification of heavy quarkonium states plays an important role in studying the hot and dense medium formed in the larger collision systems. The ATLAS detector, optimized for searching new physics in proton-proton collisions, is especially well equipped to measure Z, W bosons and quakonium in the high occupancy environment produced in heavy-ion collisions. We will present recent results on the Z boson and quarkonia yields as a function of centrality, transverse momentum and rapidity, from the ATLAS experiment.

Interactions between Global Health Initiatives and country health systems: the case of a neglected tropical diseases control program in Mali.

Science.gov (United States)

Cavalli, Anna; Bamba, Sory I; Traore, Mamadou N; Boelaert, Marleen; Coulibaly, Youssouf; Polman, Katja; Pirard, Marjan; Van Dormael, Monique

2010-08-17

Recently, a number of Global Health Initiatives (GHI) have been created to address single disease issues in low-income countries, such as poliomyelitis, trachoma, neonatal tetanus, etc.. Empirical evidence on the effects of such GHIs on local health systems remains scarce. This paper explores positive and negative effects of the Integrated Neglected Tropical Disease (NTD) Control Initiative, consisting in mass preventive chemotherapy for five targeted NTDs, on Mali's health system where it was first implemented in 2007. Campaign processes and interactions with the health system were assessed through participant observation in two rural districts (8 health centres each). Information was complemented by interviews with key informants, website search and literature review. Preliminary results were validated during feedback sessions with Malian authorities from national, regional and district levels. We present positive and negative effects of the NTD campaign on the health system using the WHO framework of analysis based on six interrelated elements: health service delivery, health workforce, health information system, drug procurement system, financing and governance. At point of delivery, campaign-related workload severely interfered with routine care delivery which was cut down or totally interrupted during the campaign, as nurses were absent from their health centre for campaign-related activities. Only 2 of the 16 health centres, characterized by a qualified, stable and motivated workforce, were able to keep routine services running and to use the campaign as an opportunity for quality improvement. Increased workload was compensated by allowances, which significantly improved staff income, but also contributed to divert attention away from core routine activities. While the campaign increased the availability of NTD drugs at country level, parallel systems for drug supply and evaluation requested extra efforts burdening local health systems. The campaign budget

Interactions between Global Health Initiatives and country health systems: the case of a neglected tropical diseases control program in Mali.

Directory of Open Access Journals (Sweden)

Anna Cavalli

Full Text Available BACKGROUND: Recently, a number of Global Health Initiatives (GHI have been created to address single disease issues in low-income countries, such as poliomyelitis, trachoma, neonatal tetanus, etc.. Empirical evidence on the effects of such GHIs on local health systems remains scarce. This paper explores positive and negative effects of the Integrated Neglected Tropical Disease (NTD Control Initiative, consisting in mass preventive chemotherapy for five targeted NTDs, on Mali's health system where it was first implemented in 2007. METHODS AND FINDINGS: Campaign processes and interactions with the health system were assessed through participant observation in two rural districts (8 health centres each. Information was complemented by interviews with key informants, website search and literature review. Preliminary results were validated during feedback sessions with Malian authorities from national, regional and district levels. We present positive and negative effects of the NTD campaign on the health system using the WHO framework of analysis based on six interrelated elements: health service delivery, health workforce, health information system, drug procurement system, financing and governance. At point of delivery, campaign-related workload severely interfered with routine care delivery which was cut down or totally interrupted during the campaign, as nurses were absent from their health centre for campaign-related activities. Only 2 of the 16 health centres, characterized by a qualified, stable and motivated workforce, were able to keep routine services running and to use the campaign as an opportunity for quality improvement. Increased workload was compensated by allowances, which significantly improved staff income, but also contributed to divert attention away from core routine activities. While the campaign increased the availability of NTD drugs at country level, parallel systems for drug supply and evaluation requested extra efforts

The effect of low capacity injection systems on transient initiated loss of vessel water injection at Browns Ferry unit one

International Nuclear Information System (INIS)

Ott, L.T.

1983-01-01

Probabilistic risk assessment (PRA) analyses have indicated the transient initiated loss of vessel water injection (TQUV sequence) to be a dominant accident scenario for BWR plants. The PRA studies assumed the low capacity injection systems to be unimportant in severe accidents. The results of a Severe Accident Sequence Analysis (SASA) Program study have shown that these systems are capable of preventing or significantly delaying core damage in a TQUV sequence

Initial results from the high resolution powder diffractometer HRPD at ISIS

International Nuclear Information System (INIS)

David, W.I.F.; Harrison, W.T.A.; Johnson, M.W.

1986-07-01

The paper reviews the initial commissioning of the high resolution time-of-flight neutron powder diffractometer, HRPD, on the Spallation Neutron Source, ISIS, at the Rutherford Appleton Laboratory. Preliminary results have confirmed both intensity and resolution predictions indicating that (Δd/d) lies between 0.04% and 0.08% for all d-spacings between 0.2 and 5A. The scientific potential of this increased resolution over existing time-of-flight diffractometers has been demonstrated in the successful ab initio structure determination of an unknown inorganic material, FeAsO 4 , and the detailed study of subtle symmetry changes in NiO. The true instrumental resolution, however, has been observed in only a small number of experiments: sample broadening is often seen to play a dominant role in the determination of the peak shape, particularly at longer d-spacings. This leads to additional useful information about macroscopic properties, such as anisotropic crystallite size, strain distribution and sample homogeneity, but also results in a significant increase in complexity of peak-shape description and data-analysis strategy. (author)

Initial testing of a Compact Crystal Positioning System for the TOPAZ Single-Crystal Diffractometer at the Spallation Neutron Source

International Nuclear Information System (INIS)

Frost, Matthew J.; Austin, Michael D.; Viola, Robert; Thomison, Jack; Carmen, Peter; Hoffmann, Christina; Miller, Echo M.; Mosier, Lisa B.; Overbay, Mark A.

2009-01-01

A precise, versatile, and automated method of orienting a sub-millimeter crystal in a focused neutron beam is required for e cient operation of the TOPAZ Single Crystal Di ractometer at the Spallation Neutron Source at Oak Ridge National Laboratory. To ful ll this need, a Compact Crystal Positioning System (CCPS) has been developed in collaboration with Square One Systems Design in Jackson, Wyoming. The system incorporates a tripod design with six vacuum-compatible piezoelectric linear motors capable of < 1 m resolution. National Instruments LabVIEW provides a means of system automation while at the same time accommodating the modular nature of the SNS sample environment control software for straightforward system integration. Initial results in a cryogenic test environment will be presented, as well as results from ambient tests performed at the Advanced Photon Source at Argonne National Laboratory.

Initial results from the ISEE-1 and -2 plasma wave investigation

International Nuclear Information System (INIS)

Gurnett, D.A.; Anderson, R.R.; Smith, E.J.

1979-01-01

In this paper the authors present an initial survey of results from the plasma wave experiments on the ISEE-1 and -2 spacecraft which are in nearly identical orbits passing through the Earth's magneotsphere at radial distances out to about 22.5 Rsub(e). Essentially every crossing of the Earth's bow shock can be associated with an intense burst of electrostatic and whistler-mode turbulence at the shock, with substanial wave intensities in both the upstream and downstream regions. In the magnetosphere high resolution spectrograms of the electric field show an extremely complex distribution of plasma and radio emission, with numerous resonance and cutoff effects. High resolution spectrograms of kilometric radio emissions are also presented which show an extremely complex frequency-time structure with many closely spaced narrow-band emissions. (Auth.)

An Analysis of the Reflector Cooling System Repair Status after the Initial Operation of HANARO

Energy Technology Data Exchange (ETDEWEB)

Park, Young Chul; Seo, Kyoung Woo; Chi, Dae Young; Yoon, Hyun Gi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Jung Geun [Safety Evaluation Department, System D and D Co., Daejeon (Korea, Republic of)

2011-05-15

HANARO, an open-tank-in-pool type multi-purpose research reactor of 30 MWth power in Korea, has been operating normally since its initial criticality in February, 1995. During the last operation period of HANARO, when a trouble occurred, the trouble was fixed on site. As preventive maintenance can reduce the corrective maintenance, the reasons of the occurred troubles are reviewed to prepare preventive maintenance. About twelve hundred cases of work requests and nonconformance reports (NCRs) have been issued since the initial criticality of HANARO. The cases are analyzed according to the trouble status, the trouble equipment function and the cause of the major trouble for reflector cooling system (RCS, hereinafter) including cover gas system and leakage monitoring and collection system

Initial Results of a New Mobile Spectrum Occupancy Monitoring Network

NARCIS (Netherlands)

van Bloem, J.W.H.; Schiphorst, Roelof; Slump, Cornelis H.

2010-01-01

In this paper we present results of the new monitoring network for spectrum governance. The network is based on the RFeye system of CRFS where the data is collected employing mobile monitoring vehicles. The measurement data, obtained from a frequency sweep between 10 MHz and 6 GHz, is further

Measuring Sustainability within the Veterans Administration Mental Health System Redesign Initiative

Science.gov (United States)

Ford, James H.; Krahn, Dean; Wise, Meg; Oliver, Karen Anderson

2011-01-01

Objective To examine how attributes affecting sustainability differ across VHA organizational components and by staff characteristics. Subjects Surveys of 870 change team members and 50 staff interviews within the VA’s Mental Health System Redesign initiative. Methods A one-way ANOVA with a Tukey post-hoc test examined differences in sustainability by VISN, job classification, and tenure from staff survey data of the Sustainability Index. Qualitative interviews used an iterative process to identify “a priori” and “in vivo” themes. A simple stepwise linear regression explored predictors of sustainability. Results Sustainability differed across VISN and staff tenure. Job classification differences existed for: 1) Benefits and Credibility of the change and 2) staff involvement and attitudes toward change. Sustainability barriers were: staff and institutional resistance, and non-supportive leadership. Facilitators were: commitment to veterans, strong leadership, and use of QI Tools. Sustainability predictors were outcomes tracking, regular reporting, and use of PDSA cycles. Conclusions Creating homogeneous implementation and sustainability processes across a national health system is difficult. Despite the VA’s best evidence-based implementation efforts, there was significant variance. Locally tailored interventions might better support sustainability than “one-size-fits all” approaches. Further research is needed to understand how participation in a QI collaborative affects sustainability. PMID:21971024

The Frontier Fields: Survey Design and Initial Results

Energy Technology Data Exchange (ETDEWEB)

Lotz, J. M.; Koekemoer, A.; Grogin, N.; Mack, J.; Anderson, J.; Avila, R.; Barker, E. A.; Borncamp, D.; Durbin, M.; Gunning, H.; Hilbert, B.; Jenkner, H.; Khandrika, H.; Levay, Z.; Lucas, R. A.; MacKenty, J.; Ogaz, S. [Space Telescope Science Institute, 3700 San Martin Drive, Baltimore, MD 21218 (United States); Coe, D.; Capak, P.; Brammer, G., E-mail: lotz@stsci.edu [European Space Agency/Space Telescope Science Institute, 3700 Sam Martin Drive, Baltimore, MD 21218 (United States); and others

2017-03-01

What are the faintest distant galaxies we can see with the Hubble Space Telescope ( HST ) now, before the launch of the James Webb Space Telescope ? This is the challenge taken up by the Frontier Fields, a Director’s discretionary time campaign with HST and the Spitzer Space Telescope to see deeper into the universe than ever before. The Frontier Fields combines the power of HST and Spitzer with the natural gravitational telescopes of massive high-magnification clusters of galaxies to produce the deepest observations of clusters and their lensed galaxies ever obtained. Six clusters—Abell 2744, MACSJ0416.1-2403, MACSJ0717.5+3745, MACSJ1149.5+2223, Abell S1063, and Abell 370—have been targeted by the HST ACS/WFC and WFC3/IR cameras with coordinated parallel fields for over 840 HST orbits. The parallel fields are the second-deepest observations thus far by HST with 5 σ point-source depths of ∼29th ABmag. Galaxies behind the clusters experience typical magnification factors of a few, with small regions magnified by factors of 10–100. Therefore, the Frontier Field cluster HST images achieve intrinsic depths of ∼30–33 mag over very small volumes. Spitzer has obtained over 1000 hr of Director’s discretionary imaging of the Frontier Field cluster and parallels in IRAC 3.6 and 4.5 μ m bands to 5 σ point-source depths of ∼26.5, 26.0 ABmag. We demonstrate the exceptional sensitivity of the HST Frontier Field images to faint high-redshift galaxies, and review the initial results related to the primary science goals.

Initial Results from the Survey of Organizational Research Climates (SOuRCe) in the U.S. Department of Veterans Affairs Healthcare System

Science.gov (United States)

Martinson, Brian C.; Nelson, David; Hagel-Campbell, Emily; Mohr, David; Charns, Martin P.; Bangerter, Ann; Thrush, Carol R.; Ghilardi, Joseph R.; Bloomfield, Hanna; Owen, Richard; Wells, James A.

2016-01-01

Background In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA) leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe) is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool. Methods We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations) believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys. Results We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of

Fission Surface Power System Initial Concept Definition

Science.gov (United States)

2010-01-01

Under the NASA Exploration Technology Development Program (ETDP) and in partnership with the Department of Energy (DOE), NASA has embarked on a project to develop Fission Surface Power (FSP) technology. The primary goals of the project are to 1) develop FSP concepts that meet expected surface power requirements at reasonable cost with added benefits over other options, 2) establish a hardwarebased technical foundation for FSP design concepts and reduce overall development risk, 3) reduce the cost uncertainties for FSP and establish greater credibility for flight system cost estimates, and 4) generate the key products to allow NASA decision-makers to consider FSP as a preferred option for flight development. The FSP project was initiated in 2006 as the Prometheus Program and the Jupiter Icy Moons Orbiter (JIMO) mission were phased-out. As a first step, NASA Headquarters commissioned the Affordable Fission Surface Power System Study to evaluate the potential for an affordable FSP development approach. With a cost-effective FSP strategy identified, the FSP team evaluated design options and selected a Preliminary Reference Concept to guide technology development. Since then, the FSP Preliminary Reference Concept has served as a point-of-departure for several NASA mission architecture studies examining the use of nuclear power and has provided the foundation for a series of "Pathfinder" hardware tests. The long-term technology goal is a Technology Demonstration Unit (TDU) integrated system test using full-scale components and a non-nuclear reactor simulator. The FSP team consists of Glenn Research Center (GRC), Marshall Space Flight Center (MSFC) and the DOE National Laboratories at Los Alamos (LANL), Idaho (INL), Oak Ridge (ORNL), and Sandia (SNL). The project is organized into two main elements: Concept Definition and Risk Reduction. Under Concept Definition, the team performs trade studies, develops analytical tools, and formulates system concepts. Under Risk

Initial Results from an Energy-Aware Airborne Dynamic, Data-Driven Application System Performing Sampling in Coherent Boundary-Layer Structures

Science.gov (United States)

Frew, E.; Argrow, B. M.; Houston, A. L.; Weiss, C.

2014-12-01

The energy-aware airborne dynamic, data-driven application system (EA-DDDAS) performs persistent sampling in complex atmospheric conditions by exploiting wind energy using the dynamic data-driven application system paradigm. The main challenge for future airborne sampling missions is operation with tight integration of physical and computational resources over wireless communication networks, in complex atmospheric conditions. The physical resources considered here include sensor platforms, particularly mobile Doppler radar and unmanned aircraft, the complex conditions in which they operate, and the region of interest. Autonomous operation requires distributed computational effort connected by layered wireless communication. Onboard decision-making and coordination algorithms can be enhanced by atmospheric models that assimilate input from physics-based models and wind fields derived from multiple sources. These models are generally too complex to be run onboard the aircraft, so they need to be executed in ground vehicles in the field, and connected over broadband or other wireless links back to the field. Finally, the wind field environment drives strong interaction between the computational and physical systems, both as a challenge to autonomous path planning algorithms and as a novel energy source that can be exploited to improve system range and endurance. Implementation details of a complete EA-DDDAS will be provided, along with preliminary flight test results targeting coherent boundary-layer structures.

Global Earth Observation System of Systems (GEOSS): Initial Actions to Enhance Data Sharing to Meet Societal Needs

Science.gov (United States)

Adang, T.

2006-05-01

Over 60 nations and 50 participating organizations are working to make the Global Earth Observation System of Systems (GEOSS) a reality. The U.S. contribution to GEOSS is the Integrated Earth Observation System (IEOS), with a vision of enabling a healthy public, economy and planet through an integrated, comprehensive, and sustained Earth observation system. The international Group on Earth Observations (GEO) and the U.S. Group on Earth Observations have developed strategic plans for both GEOSS and IEOS, respectively, and are now working the first phases of implementation. Many of these initial actions are data architecture related and are being addressed by architecture and data working groups from both organizations - the GEO Architecture and Data Committee and the USGEO Architecture and Data Management Working Group. NOAA has actively participated in both architecture groups and has taken internal action to better support GEOSS and IEOS implementation by establishing the Global Earth Observation Integrated Data Environment (GEO IDE). GEO IDE provides a "system of systems" framework for effective and efficient integration of NOAA's many quasi-independent systems, which individually address diverse mandates in such areas resource management, weather forecasting, safe navigation, disaster response, and coastal mapping among others. GEO IDE will have a services oriented architecture, allowing NOAA Line Offices to retain a high level of independence in many of their data management decisions, and encouraging innovation in pursuit of their missions. Through GEO IDE, NOAA partners (both internal and external) will participate in a well-ordered, standards-based data and information infrastructure that will allow users to easily locate, acquire, integrate and utilize NOAA data and information. This paper describes the initial progress being made by GEO and USGEO architecture and data working groups, a status report on GEO IDE development within NOAA, and an assessment of

Novel Field test design and initial result for AC and DC characterization for PV-panels

DEFF Research Database (Denmark)

Thorsteinsson, Sune; Riedel, Nicholas; Santamaria Lancia, Adrian Alejo

This work describes the design and initial test results of a field test for PV modules, where the PV modules the majority of the time operates to produce power at their maximum power point. Sequentially the individual modules are switched into a measurement circuitry for IV curves and impedance s...

77 FR 9226 - Physical Systems Integration, LLC; Supplemental Notice That Initial Market-Based Rate Filing...

Science.gov (United States)

2012-02-16

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER12-1013-000] Physical Systems Integration, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for... Physical Systems Integration, LLC's application for market-based rate authority, with an accompanying rate...

Rotary mode system initial instrument calibration

International Nuclear Information System (INIS)

Johns, B.R.

1994-01-01

The attached report contains the vendor calibration procedures used for the initial instrument calibration of the rotary core sampling equipment. The procedures are from approved vendor information files

Impact of Pre-Initiators on PSA in Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Ochirbat, Chimedtseren [KAIST, Daejeon (Korea, Republic of); Kim, Sok Chul [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2014-10-15

Most of nuclear power plants had already conducted PSA work to examine their plant safety for identifying vulnerability and preparing the mitigating strategies for severe accident. However, the PSA for research reactor has been conducted limitedly comparing with nuclear power plants due to lack of awareness and resources. Most of PSA results demonstrated that human failure events (HFEs) take a major role of risk contributor in terms of core damage frequency. HFEs are categorized as the following three types: pre-initiating event interaction (e.g., maintenance of errors, testing errors, calibration errors), initiating event related interactions (e.g., human error causing loss of power, human error causing system trip), and post-initiating event (e.g., all action actuating manual safety system backup of an automatic system). Lack of resources and utilization of research reactor calls a vicious circle in terms of safety degradation. The safety degradation poses the vulnerability of human failure during research reactor utilization process. Typically, evaluation of pre-initiators related to test and maintenance are not taking into account in PSA for research reactors. This paper aims to investigate the impact of pre-initiating events related to test and maintenance activities on PSA results in terms of core damage frequency for a research reactor.

Impact of Pre-Initiators on PSA in Research Reactor

International Nuclear Information System (INIS)

Ochirbat, Chimedtseren; Kim, Sok Chul

2014-01-01

Most of nuclear power plants had already conducted PSA work to examine their plant safety for identifying vulnerability and preparing the mitigating strategies for severe accident. However, the PSA for research reactor has been conducted limitedly comparing with nuclear power plants due to lack of awareness and resources. Most of PSA results demonstrated that human failure events (HFEs) take a major role of risk contributor in terms of core damage frequency. HFEs are categorized as the following three types: pre-initiating event interaction (e.g., maintenance of errors, testing errors, calibration errors), initiating event related interactions (e.g., human error causing loss of power, human error causing system trip), and post-initiating event (e.g., all action actuating manual safety system backup of an automatic system). Lack of resources and utilization of research reactor calls a vicious circle in terms of safety degradation. The safety degradation poses the vulnerability of human failure during research reactor utilization process. Typically, evaluation of pre-initiators related to test and maintenance are not taking into account in PSA for research reactors. This paper aims to investigate the impact of pre-initiating events related to test and maintenance activities on PSA results in terms of core damage frequency for a research reactor

Report of Committee for JAEA Internationalization Initiative

International Nuclear Information System (INIS)

2013-03-01

In global circumstances surrounding nuclear energy, the role expected to Japan Atomic Energy Agency (JAEA) is becoming increasingly important. JAEA has been promoted an initiative for the international hub in order to increase the scientific competitiveness of Japan and make international contributions, by gathering excellent researchers from the entire world with the latest facilities. Also, JAEA established 'Committee for JAEA Internationalization Initiative', which will discuss issues such as environmental improvement for accepted foreigners, direction of efforts for internationalization initiative and strategies to improve current situation. This report mentions the results of the committee's discussion including current issues for the initiative and recommendations for their solution, as well as the issues to be discussed in order to enhance international awareness of JAEA staff. The following is the summary of the recommendations for the initiative: Set up local teams that focus on the situation of each site in order to provide detailed support for foreigners from diversified backgrounds. Develop systems for emergency situations to provide information for safety swiftly for foreigners and confirm their safety, in addition to preparing emergency goods. Prepare bilingual documents and systems that foreigners need to use for their work based on importance and frequency of use of such systems and documents. (author)

General technical requirements (GTR) for inventory monitoring systems (IMS) for the trilateral initiative

International Nuclear Information System (INIS)

Pshakin, Gennady M.; Kuleshov, I.; Shea, T.; Puckett, J.M.; Zhukov, I.; Mangan, Dennis L.; Matter, John C.; Waddoups, I.; Smathers, D.; Abhold, M.E.; Hsue, S.-T.; Chiaro, P.

2002-01-01

Pursuant to the Trilateral Initiative, the three parties (The Russian Federation, the United States, and the International Atomic Energy Agency) have been engaged in discussions concerning the structure of reliable monitoring systems for storage facilities having large inventories. The intent of these monitoring systems is to provide the capability for the IAEA to maintain continuity of knowledge in a sufficiently reliable manner that should there be equipment failure, loss of continuity of knowledge would be restricted to a small population of the inventory, and thus reinventory of the stored items would be minimized These facility-specific monitoring systems, referred to as Inventory Monitoring Systems (IMS) are to provide the principal means for the M A to assure that the containers of fissile material remain accounted under the Verification Agreements which are to be concluded between the IAEA and the Russian Federation and the lAEA and the United States for the verification of weapon-origin and other fissile material specified by each State as released from its defense programs. A technical experts working group for inventory monitoring systems has been meeting since Feb- of 2000 to formulate General Technical Requirements (GTR) for Inventory Monitoring Systems for the Trilateral Initiative. Although provisional agreement has been reached by the three parties concerning the GTR, it is considered a living document that can be updated as warranted by the three parties. This paper provides a summary of the GTR as it currently exists.

A geometric initial guess for localized electronic orbitals in modular biological systems

Energy Technology Data Exchange (ETDEWEB)

Beckman, P. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Univ. of Chicago, IL (United States); Fattebert, J. L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lau, E. Y. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Osei-Kuffuor, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-11

Recent first-principles molecular dynamics algorithms using localized electronic orbitals have achieved O(N) complexity and controlled accuracy in simulating systems with finite band gaps. However, accurately deter- mining the centers of these localized orbitals during simulation setup may require O(N³) operations, which is computationally infeasible for many biological systems. We present an O(N) approach for approximating orbital centers in proteins, DNA, and RNA which uses non-localized solutions for a set of fixed-size subproblems to create a set of geometric maps applicable to larger systems. This scalable approach, used as an initial guess in the O(N) first-principles molecular dynamics code MGmol, facilitates first-principles simulations in biological systems of sizes which were previously impossible.

The development and initial assessment of the strategy and leadership systems capability evaluation survey.

Science.gov (United States)

Coon, Cheryl D; Bokowy, Kay L; Horblyuk, Ruslan; Zisman, Robert S; McLeod, Lori D; Brown, T Michelle

2012-01-01

Hospital management and leadership systems are associated with organizational success and quality care. The Strategy and Leadership Systems Capability Evaluation (CE) survey was developed by GE Healthcare to assess management and leadership systems at health care institutions, serve as a benchmark for improvement, and measure progress. To assess the psychometric properties of the 29-item CE survey, including the factor structure, scoring algorithm, reliability, and discriminant validity, an online survey was completed by 3450 employees at 15 US hospitals. Of these employees, 609 worked at a hospital where a leadership and management intervention occurred after the initial survey administration. Data were also collected on job level, number of hospital beds, hospital ownership, location, community type, and the implementation of hospital interventions. Item response frequencies showed no floor or ceiling effects and limited missing data. Interitem correlations were strong without obvious redundancies, and factor analysis suggested a unidimensional scale. The resulting scale had strong internal consistency and was able to discriminate among known groups. The CE survey was developed to evaluate management and leadership systems at health care institutions. This study provides psychometric evidence in support of the reliability, validity, and scoring structure of this survey.

Design of and initial results from a Highly Instrumented Reactor for Atmospheric Chemistry (HIRAC

Directory of Open Access Journals (Sweden)

D. R. Glowacki

2007-10-01

Full Text Available The design of a Highly Instrumented Reactor for Atmospheric Chemistry (HIRAC is described and initial results obtained from HIRAC are presented. The ability of HIRAC to perform in-situ laser-induced fluorescence detection of OH and HO₂ radicals with the Fluorescence Assay by Gas Expansion (FAGE technique establishes it as internationally unique for a chamber of its size and pressure/temperature variable capabilities. In addition to the FAGE technique, HIRAC features a suite of analytical instrumentation, including: a multipass FTIR system; a conventional gas chromatography (GC instrument and a GC instrument for formaldehyde detection; NO/NO₂, CO, O₃, and H₂O vapour analysers. Ray tracing simulations and NO₂ actinometry have been utilized to develop a detailed model of the radiation field within HIRAC. Comparisons between the analysers and the FTIR coupled to HIRAC have been performed, and HIRAC has also been used to investigate pressure dependent kinetics of the chlorine atom reaction with ethene and the reaction of O₃ and t-2-butene. The results obtained are in good agreement with literature recommendations and Master Chemical Mechanism predictions. HIRAC thereby offers a highly instrumented platform with the potential for: (1 high precision kinetics investigations over a range of atmospheric conditions; (2 detailed mechanism development, significantly enhanced according to its capability for measuring radicals; and (3 field instrument intercomparison, calibration, development, and investigations of instrument response at a range of atmospheric conditions.

E16 Sandvika-Wøyen - Analysis of tunnel excavation, achieved contour quality and influence of applied initiation system.

OpenAIRE

Sklodowska, Anna Maria

2016-01-01

The drill and blast excavation method is the most commonly used method for tunnel construction in Norway. In D&B the results from blasting can be evaluated through several factors, such as pull percentage, vibration level and contour quality. The main goal of the thesis was to analyze excavation with a special focus on the quality of the achieved contour and the influence of the applied initiation system. The analysis was performed based on results from the Bjørnegård tunnel, which wa...

Initial-boundary value problems associated with the Ablowitz-Ladik system

Science.gov (United States)

Xia, Baoqiang; Fokas, A. S.

2018-02-01

We employ the Ablowitz-Ladik system as an illustrative example in order to demonstrate how to analyze initial-boundary value problems for integrable nonlinear differential-difference equations via the unified transform (Fokas method). In particular, we express the solutions of the integrable discrete nonlinear Schrödinger and integrable discrete modified Korteweg-de Vries equations in terms of the solutions of appropriate matrix Riemann-Hilbert problems. We also discuss in detail, for both the above discrete integrable equations, the associated global relations and the process of eliminating of the unknown boundary values.

Applicability of initial stress measurement methods to Horonobe Siliceous rocks and initial stress state around Horonobe Underground Research Laboratory

International Nuclear Information System (INIS)

Sanada, Hiroyuki; Niunoya, Sumio; Matsui, Hiroya; Fujii, Yoshiaki

2009-01-01

Understanding initial stress condition in deep underground is important for such construction as rock cavern for geological disposal of HLW and underground power plant. Neogene sedimentary rock is widely distributed in Japan. There are only a few studies of initial stress measurement in Neogene sedimentary rock mass in Japan due to difficulty of measurement. Evaluation of initial stress condition around Horonobe Underground Research Laboratory Project was carried out in order to understand initial stress condition and applicability of AE, DSCA and hydraulic fracturing (HF) methods to Neogene sedimentary rock. Initial stress values obtained from AE method is smaller than overburden pressure due to time dependency of Kaizer effect. It would be difficult to use AE method as initial stress measurement method for Horonobe Siliceous rocks. Principal stress values by DSCA are similar to those by HF tests. Directions of maximum horizontal principal stresses are approximately in E-W and corresponded to HF results. In HF, rod type and wire-line type systems were compared. Workability of rod type was much better than wire-line type. However, re-opening pressure were not able to be precisely measured in case of rod type system due to the large compliance of the packers and rods. Horizontal maximum and minimum principal stresses increase linearly in HF results. Deviatoric stress is acting at shallow depth. Initial stress condition approaches hydrostatic condition with depth. Direction of maximum horizontal principal stress was in E-W direction which was similar to tectonic movement around Horonobe URL by triangular surveying. (author)

Generation of initial geometries for the simulation of the physical system in the DualPHYsics code

International Nuclear Information System (INIS)

Segura Q, E.

2013-01-01

In the diverse research areas of the Instituto Nacional de Investigaciones Nucleares (ININ) are different activities related to science and technology, one of great interest is the study and treatment of the collection and storage of radioactive waste. Therefore at ININ the draft on the simulation of the pollutants diffusion in the soil through a porous medium (third stage) has this problem inherent aspects, hence a need for such a situation is to generate the initial geometry of the physical system For the realization of the simulation method is implemented smoothed particle hydrodynamics (SPH). This method runs in DualSPHysics code, which has great versatility and ability to simulate phenomena of any physical system where hydrodynamic aspects combine. In order to simulate a physical system DualSPHysics code, you need to preset the initial geometry of the system of interest, then this is included in the input file of the code. The simulation sets the initial geometry through regular geometric bodies positioned at different points in space. This was done through a programming language (Fortran, C + +, Java, etc..). This methodology will provide the basis to simulate more complex geometries future positions and form. (Author)

Validation of a Tool for the Initial Dynamic Design of Mooring Systems for Large Floating Wave Energy Converters

Directory of Open Access Journals (Sweden)

Jonas Bjerg Thomsen

2017-09-01

Full Text Available Mooring of floating wave energy converters is an important topic in renewable research since it highly influences the overall cost of the wave energy converter and thereby the cost of energy. In addition, several wave energy converter failures have been observed due to insufficient mooring systems. When designing these systems, it is necessary to ensure the applicability of the design tool and to establish an understanding of the error between model and prototype. The present paper presents the outcome of an experimental test campaign and construction of a numerical model using the open-source boundary element method code NEMOH and the commercial time-domain mooring analysis tool OrcaFlex. The work used the wind/wave energy converter Floating Power Plant as a case study, which is defined as a large floating structure with a passive mooring system. The investigated mooring consists of a three-legged turret system with synthetic lines, and it was tested for both operational and extreme events. In order to understand the difference between the model and experimental results, no tuning of the model was done, besides adding drag elements with values found from a simplified methodology. This resembles initial design cases where no experimental data are available. Generally good agreement was found for the tensions in the lines when the drag element was applied, with some overestimation of the motions. The main cause of difference was found to be underestimation of linear damping. A model was tested with additional linear damping, and it illustrated that a final analysis needs to use experimental data to achieve the best results. However, the analyses showed that the investigated model can be used without tuning in initial investigations of mooring systems, and it is expected that this approach can be applied to other similar systems.

ODEPACK, Initial Value Problems of Ordinary Differential Equation System

International Nuclear Information System (INIS)

Hindmarsh, A.C.; Petzold, L.R.

2005-01-01

I - Description of program or function: ODEPACK is a collection of Fortran solvers for the initial value problem for ordinary differential equation systems. It consists of nine solvers, namely a basic solver called LSODE and eight variants of it -- LSODES, LSODA, LSODAR, LSODPK, LSODKR, LSODI, LSOIBT, and LSODIS. The collection is suitable for both stiff and non-stiff systems. It includes solvers for systems given in explicit form, dy/dt = f(t,y), and also solvers for systems given in linearly implicit form, A(t,y) dy/dt = g(t,y). Two of the solvers use general sparse matrix solvers for the linear systems that arise. Two others use iterative (preconditioned Krylov) methods instead of direct methods for these linear systems. The most recent addition is LSODIS, which solves implicit problems with general sparse treatment of all matrices involved. The ODEPACK solvers are written in standard Fortran 77, with a few exceptions, and with minimal machine dependencies. There are separate double and single precision versions of ODEPACK. The actual solver names are those given above with a prefix of D- or S- for the double or single precision version, respectively, i.e. DLSODE/SLSODE, etc. Each solver consists of a main driver subroutine having the same name as the solver and some number of subordinate routines. For each solver, there is also a demonstration program, which solves one or two simple problems in a somewhat self-checking manner. A. Solvers for explicitly given systems. For each of the following solvers, it is assumed that the ODEs are given explicitly, so that the system can be written in the form dy/dt = f(t,y), where y is the vector of dependent variables, and t is the independent variable. 1. LSODE (Livermore Solver for Ordinary Differential Equations) is the basic solver of the collection. It solves stiff and non-stiff systems of the form dy/dt = f. In the stiff case, it treats the Jacobian matrix df/dy as either a dense (full) or a banded matrix, and as

Analysis of results from a loss-of-offsite-power-initiated ATWS experiment in the LOFT Facility

International Nuclear Information System (INIS)

Varacalle, D.J.; Giri, A.M.; Koizumi, Y.; Koske, J.E.

1983-01-01

An anticipated transient without scram (ATWS), initiated by loss-of-offsite power, was experimentally simulated in the Loss-of-Fluid Test (LOFT) pressurized water reactor (PWR). Primary system pressure was controlled using a scaled safety relief valve (SRV) representative of those in a commercial PWR, while reactor power was reduced by moderator reactivity feedback in a natural circulation mode. The experiment showed that reactor power decreases more rapidly when the primary pumps are tripped in a loss-of-offsite-power ATWS than in a loss-of-feedwater induced ATWS when the primary pumps are left on. During the experiment, the SRV had sufficient relief capacity to control primary system pressure. Natural circulation was effective in removing core heat at high temperature, pressure, and core power. The system transient response predicted using the RELAPS/MOD1 computer code showed good agreement with the experimental data

Documentation for initial testing and inspections of Beneficial Uses Shipping System (BUSS) Cask

International Nuclear Information System (INIS)

Lundeen, J.E.

1994-01-01

The purpose of this report is to compile data generated during the initial tests and inspections of the Beneficial Uses Shipping System (BUSS) Cask. In addition, this report will verify that the testing criteria identified in section 8.1 of the BUSS Cask Safety Analysis Report for Packaging (SARP) was met. The BUSS Cask Model R-1 is a type B shipping container used for shipment of radioactive cesium-137 and strontium-90 capsules to Waste Encapsulation and Storage Facility (WESF). The BUSS Cask body and lid are each one-piece forgings fabricated from ASTM A473, Type 304 stainless steel. The primary purpose of the BUSS Cask is to provide shielding and confinement as well as impact, puncture, and thermal protection for the capsules under both normal and accident conditions. Chapter 8 of the BUSS Cask SARP requires several acceptance tests and inspections, each intended to evaluate the performance of different components of the BUSS Cask system, to be performed before its first use. The results of the tests and inspections required are included in this document

METHODOLOGICAL BACKGROUND OF EXPERT ESTIMATION OF INITIAL DATA COMPLETENESS AND QUALITY ACCORDING TO THE CERTIFIED INFORMATION SECURITY SYSTEM

Directory of Open Access Journals (Sweden)

V. K. Fisenko

2015-01-01

Full Text Available Problem of information security systems certification is analyzed and the tasks of initial data analysis are carried out. The objectives, indices and decision making criteria, as well as the challenges to be addressed are formulated. It is shown that, in order to improve quality, reduce time and cost of preparation for certification, it is reasonable to use software system for automatization of the process of initial data analysis, presented by the owner of the information system.

Scaling-up health information systems to improve HIV treatment: An assessment of initial patient monitoring systems in Mozambique.

Science.gov (United States)

Hochgesang, Mindy; Zamudio-Haas, Sophia; Moran, Lissa; Nhampossa, Leopoldo; Packel, Laura; Leslie, Hannah; Richards, Janise; Shade, Starley B

2017-01-01

The rapid scale-up of HIV care and treatment in resource-limited countries requires concurrent, rapid development of health information systems to support quality service delivery. Mozambique, a country with an 11.5% prevalence of HIV, has developed nation-wide patient monitoring systems (PMS) with standardized reporting tools, utilized by all HIV treatment providers in paper or electronic form. Evaluation of the initial implementation of PMS can inform and strengthen future development as the country moves towards a harmonized, sustainable health information system. This assessment was conducted in order to 1) characterize data collection and reporting processes and PMS resources available and 2) provide evidence-based recommendations for harmonization and sustainability of PMS. This baseline assessment of PMS was conducted with eight non-governmental organizations that supported the Ministry of Health to provide 90% of HIV care and treatment in Mozambique. The study team conducted structured and semi-structured surveys at 18 health facilities located in all 11 provinces. Seventy-nine staff were interviewed. Deductive a priori analytic categories guided analysis. Health facilities have implemented paper and electronic monitoring systems with varying success. Where in use, robust electronic PMS facilitate facility-level reporting of required indicators; improve ability to identify patients lost to follow-up; and support facility and patient management. Challenges to implementation of monitoring systems include a lack of national guidelines and norms for patient level HIS, variable system implementation and functionality, and limited human and infrastructure resources to maximize system functionality and information use. This initial assessment supports the need for national guidelines to harmonize, expand, and strengthen HIV-related health information systems. Recommendations may benefit other countries with similar epidemiologic and resource

Examining College Students' Social Environment, Normative Beliefs, and Attitudes in Subsequent Initiation of Electronic Nicotine Delivery Systems.

Science.gov (United States)

Agarwal, Deepti; Loukas, Alexandra; Perry, Cheryl L

2017-11-01

Although use of Electronic Nicotine Delivery Systems (ENDS) is increasingly prevalent among young adults, little is known about predictors of ENDS initiation among this population. We examined the roles of the social environment (i.e., peer ENDS use and household ENDS use), normative beliefs (i.e., social acceptability of ENDS use), and attitudes (i.e., inclination to date someone who uses ENDS) in prospectively predicting initiation of ENDS over a 1-year period among 18- to 29-year-old college students. Participants were 2,110 (18- to 29-year-old) students ( M = 20.27, SD = 2.17) from 24 colleges in Texas who participated in a three-wave online survey, with 6 months between each wave. All participants reported never using ENDS at baseline. A multivariable, multilevel logistic regression model, accounting for clustering of students within colleges, was used to assess if students' social environment, normative beliefs, and attitudes predicted subsequent initiation of ENDS up to 1 year later, adjusting for various sociodemographic factors and number of other tobacco products used. In all, 329 college students (16%) initiated ENDS within 1 year. Results from the logistic regression indicated that college students who were younger (18-24 years old), ever used other tobacco products, indicated a more dense peer network of ENDS users, and had a higher inclination to date someone who uses ENDS had higher odds of initiating ENDS than their peers. Preventing ENDS initiation should be included in college health promotion programs, which should highlight the roles of students' social environment and attitudes regarding ENDS use.

Results From the Audit of DOD’s American Recovery and Reinvestment Act of 2009 Initial Data Quality Review Implementation

Science.gov (United States)

2009-11-03

Results From the Audit of DoD’s American Recovery and Reinvestment Act of 2009 Initial Data Quality Review Implementation Memorandum No. D-2010-RAM...number. 1. REPORT DATE 03 NOV 2009 2. REPORT TYPE 3. DATES COVERED 00-00-2009 to 00-00-2009 4. TITLE AND SUBTITLE Results From the Audit of...SUBJECT: Results From the Audit of DOD’ s American Recovery and Reinvestment Act of2009 Initial Data Quality Review Implementation (Report No. D

75 FR 7464 - Energy Efficient Building Systems Regional Innovation Cluster Initiative-Joint Federal Funding...

Science.gov (United States)

2010-02-19

... a regional innovation cluster focused on innovation in energy efficient building technologies and... technology challenges through approaches that span basic research to engineering development to... DEPARTMENT OF ENERGY Energy Efficient Building Systems Regional Innovation Cluster Initiative...

MAARSY - The new MST radar on Andøya: System description and first results

Science.gov (United States)

Latteck, Ralph; Zecha, Marius; Rapp, Markus; Stober, Gunter; Singer, Werner; Renkwitz, Toralf

2012-07-01

In 2011 the Leibniz-Institute of Atmospheric Physics in Kühlungsborn completed the installation of the Middle Atmosphere Alomar Radar System ({MAARSY}) on the North-Norwegian island Andøya. MAARSY is a 53.5 MHz monostatic radar with an active phased array antenna consisting of 433 Yagi antennas. The 3-element Yagi antennas are arranged in an equilateral triangular grid forming a circular aperture of approximately 6300 m^2. Each individual antenna is connected to its own transceiver with independent phase control and a scalable power output of up to 2 kW. This arrangement provides very high flexibility of beam forming and beam steering with a symmetric radar beam of a minimum beam width of 3.6°. The system allows classical beam swinging operation as well as experiments with simultaneous multiple beams and the use of interferometric applications for improved studies of the Arctic atmosphere from the troposphere up to the lower thermosphere with high spatio-temporal resolution. Standard observations of tropospheric winds and polar mesosphere summer echoes started immediately with an initial stage of expansion in spring 2010. Meteor head echo experiments and 3D observations of polar mesospheric winter echoes were conducted after an upgrade of the system in December 2010. Multi-beam experiments using up to 97 beams quasi-simultaneously in the mesosphere have been carried out during campaigns in summer 2011 with the completed system. We present a system description of MAARSY including beam pattern validation and show initial results from various campaigns obtained during the first 2 years of operation.

Tangible Results and Progress in Flood Risks Management with the PACTES Initiative

Science.gov (United States)

Costes, Murielle; Abadie, Jean-Paul; Ducuing, Jean-Louis; Denier, Jean-Paul; Stéphane

The PACTES project (Prévention et Anticipation des Crues au moyen des Techniques Spatiales), initiated by CNES and the French Ministry of Research, aims at improving flood risk management, over the following three main phases : - Prevention : support and facilitate the analysis of flood risks and socio-economic impacts (risk - Forecasting and alert : improve the capability to predict and anticipate the flooding event - Crisis management : allow better situation awareness, communication and sharing of In order to achieve its ambitious objectives, PACTES: - integrates state-of-the-art techniques and systems (integration of the overall processing chains, - takes advantage of integrating recent model developments in wheather forecasting, rainfall, In this approach, space technology is thus used in three main ways : - radar and optical earth observation data are used to produce Digital Elevation Maps, land use - earth observation data are also an input to wheather forecasting, together with ground sensors; - satellite-based telecommunication and mobile positioning. Started in December 2000, the approach taken in PACTES is to work closely with users such as civil security and civil protection organisms, fire fighter brigades and city councils for requirements gathering and during the validation phase. It has lead to the development and experimentation of an integrated pre-operational demonstrator, delivered to different types of operational users. Experimentation has taken place in three watersheds representative of different types of floods (flash and plain floods). After a breaf reminder of what the PACTES project organization and aims are, the PACTES integrated pre-operational demonstrator is presented. The main scientific inputs to flood risk management are summarized. Validation studies for the three watersheds covered by PACTES (Moselle, Hérault and Thoré) are detailed. Feedback on the PACTES tangible results on flood risk management from an user point of view

Existence and smoothness of solutions to second initial boundary value problems for Schrodinger systems in cylinders with non-smooth bases

Directory of Open Access Journals (Sweden)

Nguyen Manh Hung

2008-03-01

Full Text Available In this paper, we consider the second initial boundary value problem for strongly general Schrodinger systems in both the finite and the infinite cylinders $Q_T, 0results on the existence, uniqueness and smoothness with respect to time variable of generalized solution of this problem are given.

Initial cathode processing experiences and results for the treatment of spent fuel

International Nuclear Information System (INIS)

Westphal, B.R.; Laug, D.V.; Brunsvold, A.R.; Roach, P.D.

1996-01-01

As part of the spent fuel treatment demonstration at Argonne National Laboratory, a vacuum distillation process is being employed for the recovery of uranium following an electrorefining process. Distillation of a salt electrolyte, primarily consisting of a eutectic mixture of lithium and potassium chlorides, from uranium is achieved by a batch operation termed ''cathode processing.'' Cathode processing is performed in a retort furnace which enables the production of a stable uranium product that can be isotopically diluted and stored. To date, experiments have been performed with two distillation units; one for prototypical testing and the other for actual spent fuel treatment operations. The results and experiences from these initial experiments with both units will be discussed as well as problems encountered and their resolution

Integrated modeling of natural and human systems - problems and initiatives

Science.gov (United States)

Kessler, H.; Giles, J.; Gunnink, J.; Hughes, A.; Moore, R. V.; Peach, D.

2009-12-01

's system, e.g. the flow of groundwater to an abstraction borehole or the availability of water for irrigation. Particular problems arise when model data from two or more disciplines are incompatible in terms of data formats, scientific concepts or language. Other barriers include the cultural segregation within and between science disciplines as well as impediments to data exchange due to ownership and copyright restrictions. OpenMI and GeoSciML are initiatives that are trying to overcome these barriers by building international communities that share vocabularies and data formats. This paper will give examples of the successful merging of geological and hydrological models from the UK and the Netherlands and will introduce the vision of an open Environmental Modelling Platform which aims to link data, knowledge and concepts seamlessly to numerical process models. Last but not least there is an urgent need to create a Subsurface Management System akin to a Geographic Information System in which all results of subsurface modelling can be visualised and analysed in an integrated manner.

Epistemology and expectations survey about experimental physics: Development and initial results

Directory of Open Access Journals (Sweden)

Benjamin M. Zwickl

2014-06-01

Full Text Available In response to national calls to better align physics laboratory courses with the way physicists engage in research, we have developed an epistemology and expectations survey to assess how students perceive the nature of physics experiments in the contexts of laboratory courses and the professional research laboratory. The Colorado Learning Attitudes about Science Survey for Experimental Physics (E-CLASS evaluates students’ epistemology at the beginning and end of a semester. Students respond to paired questions about how they personally perceive doing experiments in laboratory courses and how they perceive an experimental physicist might respond regarding their research. Also, at the end of the semester, the E-CLASS assesses a third dimension of laboratory instruction, students’ reflections on their course’s expectations for earning a good grade. By basing survey statements on widely embraced learning goals and common critiques of teaching labs, the E-CLASS serves as an assessment tool for lab courses across the undergraduate curriculum and as a tool for physics education research. We present the development, evidence of validation, and initial formative assessment results from a sample that includes 45 classes at 20 institutions. We also discuss feedback from instructors and reflect on the challenges of large-scale online administration and distribution of results.

Minimum ventilation systems and their effects on the initial stage of turkey production

Directory of Open Access Journals (Sweden)

AS Mendes

2013-03-01

Full Text Available This study aimed at evaluating the live performance of turkeys during the initial stage of production (1-26 days of age and to map the environmental variables inside turkey houses, such as temperature, relative humidity, CO2 concentration, at two distinct minimum ventilation systems. House 1 (H1 was equipped with a negative-pressure ventilation system and House 2 (H2 was equipped with a positive-pressure ventilation system. This study was performed in commercial poultry houses, located in Francisco Beltrão, Paraná, Brazil, in June, 2008. A number of 14,000 turkeys toms at the same age, provided by the same local hatchery and were housed at a stocking density of 23 birds m-2. Three 13 m² boxes with 300 turkeys each were placed inside the poultry houses. All treatments were assigned for the birds inside each of the three boxes. The poultry barns were virtually divided in eight equally distributed in areas where the environmental variables were recorded. The performance parameters measured were weight gain, feed conversion and mortality rate, recorded weekly. Analysis of variance and F-tests were performed to compare results within different environmental conditions, using MINITAB 14 statistical software. The ventilation systems did not significantly influence CO2 concentrations (p = 0.489, whereas temperature (p = 0.016 and relative humidity (p = 0.0001 and feed conversion (p = 0.001 were significantly affected by ventilation system. Temperature and relative humidity in H2 (positive pressure ventilation system was found to be less aversive than those in H1 (negative pressure system. Also, bids in H2 presented lower feed conversions than those in H1.

Singular Initial Value Problem for Certain Classes of Systems of Ordinary Differential Equations

Directory of Open Access Journals (Sweden)

Josef Diblík

2013-01-01

dimension of the set of initial data generating such solutions is estimated. An asymptotic behavior of solutions is determined as well and relevant asymptotic formulas are derived. The method of functions defined implicitly and the topological method (Ważewski's method are used in the proofs. The results generalize some previous ones on singular initial value problems for differential equations.

Design and initial tests of beam current monitoring systems for the APS transport lines

International Nuclear Information System (INIS)

Wang, Xucheng.

1992-01-01

The non-intercepting beam current monitoring systems suitable for a wide, range of beam parameters have been developed for the Advanced Photon Source (APS) low energy transport lines and high energy transport line. The positron or electron beam pulse in the transport lines wig have peak beam currents ranging from 8 mA to 29 A with pulse widths varying from 120 ps to 30 ns and pulse repetition rates from 2 Hz to 60 Hz. The peak beam current or total beam charge is measured with the fast or integrating current transformer, respectively, manufactured by Bergoz. In-house high speed beam signal processing electronics provide a DC level output proportional to the peak current or total charge for the digitizer input. The prototype systems were tested on the linacs which have beam pulse structures similar to that of the APS transport lines. This paper describes the design of beam signal processing electronics and grounding and shielding methods for current transformers. The results of the initial operations are presented. A short introduction on the preliminary design of current monitoring systems for the APS rings is also included

Shannon Entropy in a European Seabass (Dicentrarchus labrax System during the Initial Recovery Period after a Short-Term Exposure to Methylmercury

Directory of Open Access Journals (Sweden)

Harkaitz Eguiraun

2016-05-01

Full Text Available Methylmercury (MeHg is an environmental contaminant of increasing relevance as a seafood safety hazard that affects the health and welfare of fish. Non-invasive, on-line methodologies to monitor and evaluate the behavior of a fish system in aquaculture may make the identification of altered systems feasible—for example, due to the presence of agents that compromise their welfare and wholesomeness—and find a place in the implementation of Hazard Analysis and Critical Control Points and Fish Welfare Assurance Systems. The Shannon entropy (SE of a European seabass (Dicentrarchus labrax system has been shown to differentiate MeHg-treated from non-treated fish, the former displaying a lower SE value than the latter. However, little is known about the initial evolution of the system after removal of the toxicant. To help to cover this gap, the present work aims at providing information about the evolution of the SE of a European seabass system during a recuperation period of 11 days following a two-week treatment with 4 µg·MeHg/L. The results indicate that the SE of the system did not show a recovery trend during the examined period, displaying erratic responses with daily fluctuations and lacking a tendency to reach the initial SE values.

Initiation and continuation of long-acting reversible contraception in the United States military healthcare system.

Science.gov (United States)

Chiles, Daniel P; Roberts, Timothy A; Klein, David A

2016-09-01

Long-acting reversible contraception is more effective for pregnancy prevention than shorter-acting contraceptive methods and has the potential to reduce healthcare disparities and costs. However, long-acting reversible contraception is underused in the United States. One population of interest is beneficiaries of the United States military healthcare system who have access to universal healthcare, including no-cost, no-copay contraception with unlimited method switching, and comprise a large, actual use cohort. Efforts to increase long-acting reversible contraception initiation and continuation in this population may improve health outcomes and mitigate the profound consequences of unintended or mistimed pregnancy on readiness and cost to the military. We aimed to determine long-acting reversible contraception initiation and continuation rates among the diverse population with universal healthcare who are enrolled in the US military healthcare system. This study is a retrospective cohort of >1.7 million women, aged 14-40 years, who were enrolled in the US military healthcare system, TRICARE Prime, between October 2009 and September 2014. Individuals were assessed for long-acting reversible contraception initiation and continuation with the use of medical billing records. Method continuation and factors that were associated with early method discontinuation were evaluated with the Kaplan-Meier estimator and Cox proportional hazard models. During the study dates, 188,533 women initiated long-acting reversible contraception. Of these, 74.6% women selected intrauterine contraceptives. Method initiation rates remained relatively stable (41.7-50.1/1000 women/year) for intrauterine methods, although the rate for subdermal implants increased from 6.1-23.0/1000 women/year. In analysis of women who selected intrauterine contraceptives, 61.2% continued their method at 36 months, and 48.8% continued at 60 months. Among women who selected the implant, 32.0% continued their

Initial Results from the Survey of Organizational Research Climates (SOuRCe) in the U.S. Department of Veterans Affairs Healthcare System.

Science.gov (United States)

Martinson, Brian C; Nelson, David; Hagel-Campbell, Emily; Mohr, David; Charns, Martin P; Bangerter, Ann; Thrush, Carol R; Ghilardi, Joseph R; Bloomfield, Hanna; Owen, Richard; Wells, James A

2016-01-01

In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA) leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe) is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool. We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations) believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys. We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of results that have been

Initial Results from the Survey of Organizational Research Climates (SOuRCe in the U.S. Department of Veterans Affairs Healthcare System.

Directory of Open Access Journals (Sweden)

Brian C Martinson

Full Text Available In service to its core mission of improving the health and well-being of veterans, Veterans Affairs (VA leadership is committed to supporting research best practices in the VA. Recognizing that the behavior of researchers is influenced by the organizational climates in which they work, efforts to assess the integrity of research climates and share such information with research leadership in VA may be one way to support research best practices. The Survey of Organizational Research Climate (SOuRCe is the first validated survey instrument specifically designed to assess the organizational climate of research integrity in academic research organizations. The current study reports on an initiative to use the SOuRCe in VA facilities to characterize the organizational research climates and pilot test the effectiveness of using SOuRCe data as a reporting and feedback intervention tool.We administered the SOuRCe using a cross-sectional, online survey, with mailed follow-up to non-responders, of research-engaged employees in the research services of a random selection of 42 VA facilities (e.g., Hospitals/Stations believed to employ 20 or more research staff. We attained a 51% participation rate, yielding more than 5,200 usable surveys.We found a general consistency in organizational research climates across a variety of sub-groups in this random sample of research services in the VA. We also observed similar SOuRCe scale score means, relative rankings of these scales and their internal reliability, in this VA-based sample as we have previously documented in more traditional academic research settings. Results also showed more substantial variability in research climate scores within than between facilities in the VA research service as reflected in meaningful subgroup differences. These findings suggest that the SOuRCe is suitable as an instrument for assessing the research integrity climates in VA and that the tool has similar patterns of results that

New mechanism of spiral wave initiation in a reaction-diffusion-mechanics system.

Science.gov (United States)

Weise, Louis D; Panfilov, Alexander V

2011-01-01

Spiral wave initiation in the heart muscle is a mechanism for the onset of dangerous cardiac arrhythmias. A standard protocol for spiral wave initiation is the application of a stimulus in the refractory tail of a propagating excitation wave, a region that we call the "classical vulnerable zone." Previous studies of vulnerability to spiral wave initiation did not take the influence of deformation into account, which has been shown to have a substantial effect on the excitation process of cardiomyocytes via the mechano-electrical feedback phenomenon. In this work we study the effect of deformation on the vulnerability of excitable media in a discrete reaction-diffusion-mechanics (dRDM) model. The dRDM model combines FitzHugh-Nagumo type equations for cardiac excitation with a discrete mechanical description of a finite-elastic isotropic material (Seth material) to model cardiac excitation-contraction coupling and stretch activated depolarizing current. We show that deformation alters the "classical," and forms a new vulnerable zone at longer coupling intervals. This mechanically caused vulnerable zone results in a new mechanism of spiral wave initiation, where unidirectional conduction block and rotation directions of the consequently initiated spiral waves are opposite compared to the mechanism of spiral wave initiation due to the "classical vulnerable zone." We show that this new mechanism of spiral wave initiation can naturally occur in situations that involve wave fronts with curvature, and discuss its relation to supernormal excitability of cardiac tissue. The concept of mechanically induced vulnerability may lead to a better understanding about the onset of dangerous heart arrhythmias via mechano-electrical feedback.

Extended Plate and Beam Wall System: Concept Investigation and Initial Evaluation

Energy Technology Data Exchange (ETDEWEB)

Wiehagen, J. [Partnership for Home Innovation, Upper Marlboro, MD (United States); Kochkin, V. [Partnership for Home Innovation, Upper Marlboro, MD (United States)

2015-08-01

A new and innovative High-R wall design, referred to as the Extended Plate & Beam (EP&B), is under development. The EP&B system uniquely integrates foam sheathing insulation with wall framing such that wood structural panels are installed exterior of the foam sheathing, enabling the use of standard practices for installation of drainage plane, windows and doors, claddings, cavity insulation, and the standard exterior foam sheathing installation approach prone to damage of the foam during transportation of prefabricated wall panels. As part of the ongoing work, the EP&B wall system concept has undergone structural verification testing and has been positively vetted by a group of industry stakeholders. Having passed these initial milestone markers, the advanced wall system design has been analyzed to assess cost implications relative to other advanced wall systems, undergone design assessment to develop construction details, and has been evaluated to develop representative prescriptive requirements for the building code. This report summarizes the assessment steps conducted to-date and provides details of the concept development.

Spinal epidural neurostimulation for treatment of acute and chronic intractable pain: initial and long term results.

Science.gov (United States)

Richardson, R R; Siqueira, E B; Cerullo, L J

1979-09-01

Spinal epidural neurostimulation, which evolved from dorsal column stimulation, has been found to be effective in the treatment of acute and chronic intractable pain. Urban and Hashold have shown that it is a safe, simplified alternative to dorsal column stimulation, especially because laminectomy is not required if the electrodes are inserted percutaneously. Percutaneous epidural neurostimulation is also advantageous because there can be a diagnostic trial period before permanent internalization and implantation. This diagnostic and therapeutic modality has been used in 36 patients during the past 3 years at Northwestern Memorial Hospital. Eleven of these patients had acute intractable pain, which was defined as pain of less than 1 year in duration. Initial postimplantation results from the 36 patients indicate that spinal epidural neurostimulation is most effective in treating the intractable pain of diabetes, arachnoiditis, and post-traumatic and postamputation neuroma. Long term follow-up, varying from 1 year to 3 years postimplantation in the 20 initially responding patients, indicates that the neurostimulation continues to provide significant pain relief (50% or greater) in a majority of the patients who experienced initial significant pain relief.

Initial results from the StratoClim aircraft campaign in the Asian Monsoon in summer 2017

Science.gov (United States)

Rex, M.

2017-12-01

The Asian Monsoon System is one of the Earth's largest and most energetic weather systems. Monsoon rainfall is critical to feeding over a billion people in Asia and the monsoon circulation affects weather patterns over the entire northern hemisphere. The Monsoon also acts like an enormous elevator, pumping vast amounts of air and pollutants from the surface up to the tropopause region at levels above 16km altitude, from where air can ascend into the stratosphere, where it spreads globally. Thus the monsoon affects the chemical composition of the global tropopause region and the stratosphere, and hence plays a key role for the composition of the UTS. Dynamically the monsoon circulation leads to the formation of a large anticyclone at tropopause levels above South Asia - the Asian Monsoon Anticyclone (AMA). Satellite images show a large cloud of aerosols directly above the monsoon, the Asian Tropopause Aerosol Layer (ATAL). In July to August 2017 the international research project StratoClim carried out the first in-situ aircraft measurements in the AMA and the ATAL with the high altitude research aircraft M55-Geophysica. Around 8 scientific flights took place in the airspaces of Nepal, India and Bangladesh and have horizontally and vertically probed the AMA and have well characterized the ATAL along flight patterns that have been carefully designed by a theory, modelling and satellite data analysing team in the field. The aircraft campaign has been complemented by launches of research balloons from ground stations in Nepal, Bangladesh, China and Palau. The presentation will give an overview of the StratoClim project, the aircraft and balloon activities and initial results from the StratoClim Asian Monsoon campaign in summer 2017.

The SAGES Legacy Unifying Globulars and Galaxies survey (SLUGGS): sample definition, methods, and initial results

Energy Technology Data Exchange (ETDEWEB)

Brodie, Jean P.; Romanowsky, Aaron J.; Jennings, Zachary G.; Pota, Vincenzo; Kader, Justin; Roediger, Joel C.; Villaume, Alexa; Arnold, Jacob A.; Woodley, Kristin A. [University of California Observatories, 1156 High Street, Santa Cruz, CA 95064 (United States); Strader, Jay [Department of Physics and Astronomy, Michigan State University, East Lansing, MI 48824 (United States); Forbes, Duncan A.; Pastorello, Nicola; Usher, Christopher; Blom, Christina; Kartha, Sreeja S. [Centre for Astrophysics and Supercomputing, Swinburne University, Hawthorn, VIC 3122 (Australia); Foster, Caroline; Spitler, Lee R., E-mail: jbrodie@ucsc.edu [Australian Astronomical Observatory, P.O. Box 915, North Ryde, NSW 1670 (Australia)

2014-11-20

We introduce and provide the scientific motivation for a wide-field photometric and spectroscopic chemodynamical survey of nearby early-type galaxies (ETGs) and their globular cluster (GC) systems. The SAGES Legacy Unifying Globulars and GalaxieS (SLUGGS) survey is being carried out primarily with Subaru/Suprime-Cam and Keck/DEIMOS. The former provides deep gri imaging over a 900 arcmin{sup 2} field-of-view to characterize GC and host galaxy colors and spatial distributions, and to identify spectroscopic targets. The NIR Ca II triplet provides GC line-of-sight velocities and metallicities out to typically ∼8 R {sub e}, and to ∼15 R {sub e} in some cases. New techniques to extract integrated stellar kinematics and metallicities to large radii (∼2-3 R {sub e}) are used in concert with GC data to create two-dimensional (2D) velocity and metallicity maps for comparison with simulations of galaxy formation. The advantages of SLUGGS compared with other, complementary, 2D-chemodynamical surveys are its superior velocity resolution, radial extent, and multiple halo tracers. We describe the sample of 25 nearby ETGs, the selection criteria for galaxies and GCs, the observing strategies, the data reduction techniques, and modeling methods. The survey observations are nearly complete and more than 30 papers have so far been published using SLUGGS data. Here we summarize some initial results, including signatures of two-phase galaxy assembly, evidence for GC metallicity bimodality, and a novel framework for the formation of extended star clusters and ultracompact dwarfs. An integrated overview of current chemodynamical constraints on GC systems points to separate, in situ formation modes at high redshifts for metal-poor and metal-rich GCs.

Ongoing Initiatives to Improve the Quality and Efficiency of Medicine Use within the Public Healthcare System in South Africa; A Preliminary Study

Directory of Open Access Journals (Sweden)

Johanna C. Meyer

2017-11-01

Full Text Available Introduction: South Africa has an appreciable burden of both communicable and non-communicable diseases as well as high maternal, neonatal, and child morbidity. In recent years there have been significant strides with improving the public health system, and addressing current inequalities, with the right to health a constitutional provision in South Africa. Initiatives include the introduction of National Health Insurance, programmes to enhance access to medicines for patients with chronic diseases, as well as activities to improve care in hospitals, including improving pharmacovigilance. Consequently, the objective of this paper is to review ongoing initiatives within the public healthcare sector in South Africa and their influence to provide future direction.Method: Principally a structured review of current and planned activities.Results: There have been a number of major activities and initiatives surrounding the availability and access to medicines in the public system in recent years in South Africa. This includes a National Surveillance Centre and an innovative early warning system for the supply of medicines as well as the development of a National Health Care Pricing Authority and initiatives to improve contracting. There have also been developments to improve the supply chain including instigating Medicine Procurement Units in the provinces and enhancing forecasting capabilities. Access to medicines is improving though the instigation of stable chronic disease management initiatives to increase the number of external pick-up points for medicines. There are also ongoing programmes to enhance adherence to medicines as well as enhance adherence to the Standard Treatment Guidelines and the Essential Medicines List with their increasing availability. In addition, there is a movement to enhance the role of health technology assessment in future decision making. Hospital initiatives include increased focus on reducing antimicrobial resistance

Initial high-power testing of the ATF [Advanced Toroidal Facility] ECH [electron cyclotron heating] system

International Nuclear Information System (INIS)

White, T.L.; Bigelow, T.S.; Kimrey, H.D. Jr.

1987-01-01

The Advanced Toroidal Facility (ATF) is a moderate aspect ratio torsatron that will utilize 53.2 GHz 200 kW Electron Cyclotron Heating (ECH) to produce nearly current-free target plasmas suitable for subsequent heating by strong neutral beam injection. The initial configuration of the ECH system from the gyrotron to ATF consists of an optical arc detector, three bellows, a waveguide mode analyzer, two TiO 2 mode absorbers, two 90 0 miter bends, two waveguide pumpouts, an insulating break, a gate valve, and miscellaneous straight waveguide sections feeding a launcher radiating in the TE 02 mode. Later, a focusing Vlasov launcher will be added to beam the ECH power to the saddle point in ATF magnetic geometry for optimum power deposition. The ECH system has several unique features; namely, the entire ECH system is evacuated, the ECH system is broadband, forward power is monitored by a newly developed waveguide mode analyzer, phase correcting miter bends will be employed, and the ECH system will be capable of operating short pulse to cw. Initial high-power tests show that the overall system efficiency is 87%. The waveguide mode analyzer shows that the gyrotron mode output consists of 13% TE 01 , 82.6% TE 02 , 2.5% TE 03 , and 1.9% TE 04 . 4 refs

76 FR 2368 - Balance Power Systems, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...

Science.gov (United States)

2011-01-13

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER11-2331-000] Balance Power Systems, LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for Blanket... proceeding of Balance Power Systems, LLC's application for market-based rate authority, with an accompanying...

Crew and Thermal Systems Strategic Communications Initiatives in Support of NASA's Strategic Goals

Science.gov (United States)

Paul, Heather L.; Lamberth, Erika Guillory; Jennings, Mallory A.

2012-01-01

NASA has defined strategic goals to invest in next-generation technologies and innovations, inspire students to become the future leaders of space exploration, and expand partnerships with industry and academia around the world. The Crew and Thermal Systems Division (CTSD) at the NASA Johnson Space Center actively supports these NASA initiatives. In July 2011, CTSD created a strategic communications team to communicate CTSD capabilities, technologies, and personnel to external technical audiences for business development and collaborative initiatives, and to students, educators, and the general public for education and public outreach efforts. This paper summarizes the CTSD Strategic Communications efforts and metrics through the first half of fiscal year 2012 with projections for end of fiscal year data.

Crew and Thermal Systems Strategic Communications Initiatives in Support of NASA's Strategic Goals

Science.gov (United States)

Paul, Heather L.

2012-01-01

NASA has defined strategic goals to invest in next-generation technologies and innovations, to inspire students to become the future leaders of space exploration, and to expand partnerships with industry and academia around the world. The Crew and Thermal Systems Division (CTSD) at the NASA Johnson Space Center actively supports these NASA initiatives. In July 2011, CTSD created a strategic communications team to communicate CTSD capabilities, technologies, and personnel to internal NASA and external technical audiences for business development and collaborative initiatives, and to students, educators, and the general public for education and public outreach efforts. This paper summarizes the CTSD Strategic Communications efforts and metrics through the first nine months of fiscal year 2012.

SYNTHESIS OF STYRENE-BUTADIENE STATISTIC COPOLYMERS CONTAINING MAGNESIUM INITIATOR

Directory of Open Access Journals (Sweden)

A. V. Firsova

2015-01-01

Full Text Available The article discusses the use of organomagnesium initiators in the synthesis of styrene-butadiene random copolymer (SBR obtained solution polymerization and their influence on the properties of rubber. Selected organic magnesium dialkyl initiator is combined with a modifier, which is a mixed alkoxide of an alkali and alkaline earth metals, which allows to control the micr ostructure of the diene polymer and its molecular weight characteristics. Alcohol derivatives selected high-boiling alcohols tetra (hydroxypropyl ethylenediamine (lapromol 294 and tetrahydrofurfuryl alcohol (TGFS. Selection of high-boiling alcohols due to the fact that the destruction of alkoxide with aqueous polymer degassing they do not fall into the return solvent and almost fall into the exact water. The metal components of alkoxides are lithium, sodium, potassium, magnesium and calcium. The resulting solutions are stable when stored modifier t hroughout the year even at -40 °C. The scheme of obtaining the new catalyst systems based organomagnesium and alcoxide of alkali and alkaline earth metals, which yields as functionalized SBR with a statistical and a distribution block of butadiene and styrene was developed. The process of copolymerization with styrene to butadiene organomagnesium initiators as using an organolithium compound (n-butyllithium was carried out, and without it. Found that the addition of n-butyllithium in the reaction mixture leads to a sharp increase in the rate of reaction. The results of studies of the effect of composition of the initiator system on the structure of diene polymers. It was revealed that a mixed initiator system affords a high conversion of monomers (to 90 % in 1 hour 1,2-polybutadiene content increased to 60 %. The process of polymerization of only a mixture of organomagnesium initiators and alcoxide of alkali and alkaline earth metals are not actively proceeds, conversion of the monomers reaches to 90 % in 4 hours, the microstructure

Software Development Initiatives to Identify and Mitigate Security Threats - Two Systematic Mapping Studies

Directory of Open Access Journals (Sweden)

Paulina Silva

2016-12-01

Full Text Available Software Security and development experts have addressed the problem of building secure software systems. There are several processes and initiatives to achieve secure software systems. However, most of these lack empirical evidence of its application and impact in building secure software systems. Two systematic mapping studies (SM have been conducted to cover the existent initiatives for identification and mitigation of security threats. The SMs created were executed in two steps, first in 2015 July, and complemented through a backward snowballing in 2016 July. Integrated results of these two SM studies show a total of 30 relevant sources were identified; 17 different initiatives covering threats identification and 14 covering the mitigation of threats were found. All the initiatives were associated to at least one activity of the Software Development Lifecycle (SDLC; while 6 showed signs of being applied in industrial settings, only 3 initiatives presented experimental evidence of its results through controlled experiments, some of the other selected studies presented case studies or proposals.

Cauchy problem with general discontinuous initial data along a smooth curve for 2-d Euler system

Science.gov (United States)

Chen, Shuxing; Li, Dening

2014-09-01

We study the Cauchy problems for the isentropic 2-d Euler system with discontinuous initial data along a smooth curve. All three singularities are present in the solution: shock wave, rarefaction wave and contact discontinuity. We show that the usual restrictive high order compatibility conditions for the initial data are automatically satisfied. The local existence of piecewise smooth solution containing all three waves is established.

Control of Insects in Slash Pine Cones with Trunk Implantations of Bidrin® Systemic Insecticide - First-Year Results

Science.gov (United States)

Edward P. Merkel

1969-01-01

Initial experiments with the implantation of the systemic insecticide Bidrin® into the trunks of slash pines in a seed production area resulted in various degrees of control of coneworms, Dioryctria spp., and the pine seed-worm, Laspeyresia anaronjada Miller, depending on dosage rates and time of application. When applied in early...

Tablets in Education. Results from the Initiative ETiE, for Teaching Plants to Primary School Students

Science.gov (United States)

Fokides, Emmanuel; Atsikpasi, Pinelopi

2017-01-01

The study presents the results from the first phase of the initiative Emerging Technologies in Education. At this stage, we examined the learning outcomes from the use of tablets and an application as content delivery methods for teaching plants' parts, reproduction types and organs, photosynthesis, and respiration. The project lasted for four…

Influence of solitons in the initial state on chaos in the driven damped sine-Gordon system

Energy Technology Data Exchange (ETDEWEB)

Bishop, A R; Fesser, K; Lomdahl, P S; Trullinger, S E

1983-01-01

The appearance of chaos in the a.c. driven, damped sine-Gordon equation is studied numerically. Several transitions from periodic to chaotic behavior are investigated in detail for flat initial conditions. Spatial structures (breather, kink) in the initial conditions smooth out many of these transitions and give rise to an interesting symbiosis of time and spatial intermittency. This symbiosis appears to be due to the competition between the background tendency towards chaos and the system's preference to maintain a spatial pattern. The way that this competition is relieved is also found to depend very strongly on symmetry in the initial conditions.

A common evaluation framework for the African Health Initiative

Science.gov (United States)

2013-01-01

Background The African Health Initiative includes highly diverse partnerships in five countries (Ghana, Mozambique, Rwanda, Tanzania, and Zambia), each of which is working to improve population health by strengthening health systems and to evaluate the results. One aim of the Initiative is to generate cross-site learning that can inform implementation in the five partnerships during the project period and identify lessons that may be generalizable to other countries in the region. Collaborators in the Initiative developed a common evaluation framework as a basis for this cross-site learning. Methods This paper describes the components of the framework; this includes the conceptual model, core metrics to be measured in all sites, and standard guidelines for reporting on the implementation of partnership activities and contextual factors that may affect implementation, or the results it produces. We also describe the systems that have been put in place for data management, data quality assessments, and cross-site analysis of results. Results and conclusions The conceptual model for the Initiative highlights points in the causal chain between health system strengthening activities and health impact where evidence produced by the partnerships can contribute to learning. This model represents an important advance over its predecessors by including contextual factors and implementation strength as potential determinants, and explicitly including equity as a component of both outcomes and impact. Specific measurement challenges include the prospective documentation of program implementation and contextual factors. Methodological issues addressed in the development of the framework include the aggregation of data collected using different methods and the challenge of evaluating a complex set of interventions being improved over time based on continuous monitoring and intermediate results. PMID:23819778

New mechanism of spiral wave initiation in a reaction-diffusion-mechanics system.

Directory of Open Access Journals (Sweden)

Louis D Weise

Full Text Available Spiral wave initiation in the heart muscle is a mechanism for the onset of dangerous cardiac arrhythmias. A standard protocol for spiral wave initiation is the application of a stimulus in the refractory tail of a propagating excitation wave, a region that we call the "classical vulnerable zone." Previous studies of vulnerability to spiral wave initiation did not take the influence of deformation into account, which has been shown to have a substantial effect on the excitation process of cardiomyocytes via the mechano-electrical feedback phenomenon. In this work we study the effect of deformation on the vulnerability of excitable media in a discrete reaction-diffusion-mechanics (dRDM model. The dRDM model combines FitzHugh-Nagumo type equations for cardiac excitation with a discrete mechanical description of a finite-elastic isotropic material (Seth material to model cardiac excitation-contraction coupling and stretch activated depolarizing current. We show that deformation alters the "classical," and forms a new vulnerable zone at longer coupling intervals. This mechanically caused vulnerable zone results in a new mechanism of spiral wave initiation, where unidirectional conduction block and rotation directions of the consequently initiated spiral waves are opposite compared to the mechanism of spiral wave initiation due to the "classical vulnerable zone." We show that this new mechanism of spiral wave initiation can naturally occur in situations that involve wave fronts with curvature, and discuss its relation to supernormal excitability of cardiac tissue. The concept of mechanically induced vulnerability may lead to a better understanding about the onset of dangerous heart arrhythmias via mechano-electrical feedback.

Preliminary results of proton therapy in choroidal melanoma at the centre de proton therapy d'Orsay (C.P.O.): 464 initial cases

International Nuclear Information System (INIS)

Desjardins, L.; Levy, C.; D'hermies, F.; Frau, E.; Schlienger, P.; Habrand, J.L.; Mammar, H.; Schwartz, L.; Mazal, A.; Delacroix, S.; Nauraye, C.; Ferrand, R.; Asselain, B.

1997-01-01

Retrospective analysis of the treatment of choroidal melanoma with proton-therapy at the Centre de protontherapie d'Orsay, France. Between September 1991 and September 1995, 612 patients presenting with choroidal melanoma were treated by proton-therapy in Orsay. Following initial management of the first 464 patients, results were analyzed, as were results after a 1-year follow up for 305 patients, a 2-year follow-up for 169 patients, and a 3-year follow-up for 59 patients. Univariate analysis showed that the actuarial local recurrence rate was 5 %, the 3-year survival rate 88 %, and the overall metastatic rate 5%. The initial tumor volume was the most significant predictive factor for visual results and metastases. Multivariate analysis revealed that visual results were significantly related to the initial tumor volume, initial retinal detachment, and total dose delivered to the optic nerve and macula. Proton-therapy of choroidal melanoma allows in most cases conservation of the eye without modification of survival. Visual results mainly depend on the site and size of the tumor. (author)

System modeling and reactor design studies of the Advanced Thermionic Initiative space nuclear reactor

International Nuclear Information System (INIS)

Lee, H.H.; Abdul-Hamid, S.; Klein, A.C.

1996-01-01

In-core thermionic space reactor design concepts that operate at a nominal power output range of 20 to 50 kW(electric) are described. Details of the neutronic, thermionic, thermal hydraulics, and shielding performance are presented. Because of the strong absorption of thermal neutrons by natural tungsten and the large amount of natural tungsten within the reactor core, two designs are considered. An overall system design code has been developed at Oregon State University to model advanced in-core thermionic energy conversion-based nuclear reactor systems for space applications. The results show that the driverless single-cell Advanced Thermionic Initiative (ATI) configuration, which does not have driver fuel rods, proved to be more efficient than the driven core, which has driver rods. The results also show that the inclusion of the true axial and radial power distribution decrease the overall conversion efficiency. The flattening of the radial power distribution by three different methods would lead to a higher efficiency. The results show that only one TFE works at the optimum emitter temperature; all other TFEs are off the optimum performance and result in a 40% decrease of the efficiency of the overall system. The true axial profile is significantly different as there is a considerable amount of neutron leakage out of the top and bottom of the reactor. The analysis reveals that the axial power profile actually has a chopped cosine shape. For this axial profile, the reactor core overall efficiency for the driverless ATI reactor version is found to be 5.84% with a total electrical power of 21.92 kW(electric). By considering the true axial power profile instead of the uniform power profile, each TFE loses ∼80 W(electric)

Results of the initial test program for the Sandia Pulsed Reactor III (SPR III)

International Nuclear Information System (INIS)

Estes, B.F.; Reuscher, J.A.

1976-08-01

This document presents a detailed discussion of the reactor including the mechanical and nuclear design characteristics. Also presented are the complete results of the Initial Approach to Critical and the Zero-and-Low Power testing programs. Reactivity worth measurements are given for such parameters as control element integral worth, Safety Block integral worth, and various materials (polyethylene, copper, lead, etc) as a function of position relative to the core. Subcritical reactivity measurements made during the approach to critical generally proved to be in reasonably good agreement with design values due to the good source-fuel-detector geometry possible with a reactor of this type. Subsequent dynamic measurements for reactivity worths are shown to be in good agreement with calculated results

Stand alone photovoltaic systems: guarantee of results

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

This study aims to provide a guarantee of results for system performance for users of stand-alone photovoltaic (PV) systems, which have no back-up generator. The appropriate main performance criterion for PV systems is that a specified load is supplied with power either continuously or intermittently whenever the load requires power. A methodology to evaluate the power availability of stand-alone PV systems has been developed as part of the project, which encompasses power losses due to weather variations. The guarantee of results produced allows users to compare system designs from different manufacturers. (UK)

How can insulin initiation delivery in a dual-sector health system be optimised? A qualitative study on healthcare professionals’ views

Directory of Open Access Journals (Sweden)

Lee Ping Yein

2012-04-01

Full Text Available Abstract Background The prevalence of type 2 diabetes is increasing at an alarming rate in developing countries. However, glycaemia control remains suboptimal and insulin use is low. One important barrier is the lack of an efficient and effective insulin initiation delivery approach. This study aimed to document the strategies used and proposed by healthcare professionals to improve insulin initiation in the Malaysian dual-sector (public–private health system. Methods In depth interviews and focus group discussions were conducted in Klang Valley and Seremban, Malaysia in 2010–11. Healthcare professionals consisting of general practitioners (n = 11, medical officers (n = 8, diabetes educators (n = 3, government policy makers (n = 4, family medicine specialists (n = 10 and endocrinologists (n = 2 were interviewed. We used a topic guide to facilitate the interviews, which were audio recorded, transcribed verbatim and analysed using a thematic approach. Results Three main themes emerged from the interviews. Firstly, there was a lack of collaboration between the private and public sectors in diabetes care. The general practitioners in the private sector proposed an integrated system for them to refer patients to the public health services for insulin initiation programmes. There could be shared care between the two sectors and this would reduce the disproportionately heavy workload at the public sector. Secondly, besides the support from the government health authority, the healthcare professionals wanted greater involvement of non-government organisations, media and pharmaceutical industry in facilitating insulin initiation in both the public and private sectors. The support included: training of healthcare professionals; developing and disseminating patient education materials; service provision by diabetes education teams; organising programmes for patients’ peer group sessions; increasing awareness and demystifying

Use of a temperature-initiated passive cooling system (TIPACS) for the modular high-temperature gas-cooled reactor cavity cooling system (RCCS)

International Nuclear Information System (INIS)

Forsberg, C.W.; Conklin, J.; Reich, W.J.

1994-04-01

A new type of passive cooling system has been invented (Forsberg 1993): the Temperature-Initiated Passive Cooling System (TIPACS). The characteristics of the TIPACS potentially match requirements for an improved reactor-cavity-cooling system (RCCS) for the modular high-temperature gas-cooled reactor (MHTGR). This report is an initial evaluation of the TIPACS for the MHTGR with a Rankines (steam) power conversion cycle. Limited evaluations were made of applying the TIPACS to MHTGRs with reactor pressure vessel temperatures up to 450 C. These temperatures may occur in designs of Brayton cycle (gas turbine) and process heat MHTGRs. The report is structured as follows. Section 2 describes the containment cooling issues associated with the MHTGR and the requirements for such a cooling system. Section 3 describes TIPACS in nonmathematical terms. Section 4 describes TIPACS's heat-removal capabilities. Section 5 analyzes the operation of the temperature-control mechanism that determines under what conditions the TIPACS rejects heat to the environment. Section 6 addresses other design and operational issues. Section 7 identifies uncertainties, and Section 8 provides conclusions. The appendixes provide the detailed data and models used in the analysis

Use of a temperature-initiated passive cooling system (TIPACS) for the modular high-temperature gas-cooled reactor cavity cooling system (RCCS)

Energy Technology Data Exchange (ETDEWEB)

Forsberg, C.W.; Conklin, J.; Reich, W.J.

1994-04-01

A new type of passive cooling system has been invented (Forsberg 1993): the Temperature-Initiated Passive Cooling System (TIPACS). The characteristics of the TIPACS potentially match requirements for an improved reactor-cavity-cooling system (RCCS) for the modular high-temperature gas-cooled reactor (MHTGR). This report is an initial evaluation of the TIPACS for the MHTGR with a Rankines (steam) power conversion cycle. Limited evaluations were made of applying the TIPACS to MHTGRs with reactor pressure vessel temperatures up to 450 C. These temperatures may occur in designs of Brayton cycle (gas turbine) and process heat MHTGRs. The report is structured as follows. Section 2 describes the containment cooling issues associated with the MHTGR and the requirements for such a cooling system. Section 3 describes TIPACS in nonmathematical terms. Section 4 describes TIPACS`s heat-removal capabilities. Section 5 analyzes the operation of the temperature-control mechanism that determines under what conditions the TIPACS rejects heat to the environment. Section 6 addresses other design and operational issues. Section 7 identifies uncertainties, and Section 8 provides conclusions. The appendixes provide the detailed data and models used in the analysis.

Pneumatosis Intestinalis as the Initial Presentation of Systemic Sclerosis: A Case Report and Review of the Literature

Directory of Open Access Journals (Sweden)

Farshid Ejtehadi

2012-01-01

Full Text Available Introduction. Pneumatosis intestinalis (PI is an uncommon pathology characterised by the presence of gas within the intestinal wall. It has been associated with various conditions, including connective tissue diseases. This is the first report of PI being the initial presentation of systemic sclerosis. Case Presentation. The patient, a 75-year-old female, presented with an 8-month history of worsening dysphagia and epigastric pain, as well as other nonspecific symptoms. Initial investigations with an oesophagogastroduodenoscopy diagnosed Candida oesophagitis and also identified an extrinsic compression of the gastric antrum. Subsequently a CT scan of the abdomen and pelvis showed moderately dilated small bowel loops and PI. Due to the patient’s stability, non-critical clinical condition, conservative management was instituted. More detailed investigations confirmed the diagnosis of systemic sclerosis with positive anticentromeric and antinuclear antibodies. The patient improved on methotrexate and was discharged with appropriate outpatient follow-up. Discussion. PI is a rare but well-documented pathology associated with connective tissue diseases, such as systemic sclerosis. In most cases, conservative management is preferable to surgical intervention, depending on the patient’s clinical presentation and progress. This is the first report of PI being the initial presentation of a patient with systemic sclerosis responsive to conservative management.

Initial test results of the Omron face cue entry system at the University of Missouri-Rolla Reactor

International Nuclear Information System (INIS)

Tokuhiro, Akira T.; Vaughn, Brian J.

2004-01-01

The University of Missouri-Rolla Reactor facility is testing, in collaboration with Omron Transaction Systems, Inc., the Omron Face Cue facial recognition system for access control to its restricted area. The installation of this system is the first of its kind at a security-relevant facility in the U.S. and within the research reactor community. The Face Cue is an on-demand device based on facial recognition and storage technology. The image processing methodology is as follows: (1) facial position detection, (2) background elimination, (3) facial features discrimination via application of a wavelet transform. The extracted facial feature values are compared to the data archived in its database and access is provided upon meeting the authorization criteria. The current test phase consisted of assessing the functionality of the Face Cue during daily use and in terms of its robustness (flexibility) as a function of the following physical parameters: (1) subject's distance away from the Face Cue, (2) ambient lighting conditions, (3) subject's facial orientation, (4) subject's facial expression and (5) peripheral facial features/modifications. The system has operated at nearly 100% reliability during several test intervals with approximately 7,000 entry attempts to date. (author)

Impact of an electronic alert notification system embedded in radiologists' workflow on closed-loop communication of critical results: a time series analysis.

Science.gov (United States)

Lacson, Ronilda; O'Connor, Stacy D; Sahni, V Anik; Roy, Christopher; Dalal, Anuj; Desai, Sonali; Khorasani, Ramin

2016-07-01

Optimal critical test result communication is a Joint Commission national patient safety goal and requires documentation of closed-loop communication among care providers in the medical record. Electronic alert notification systems can facilitate an auditable process for creating alerts for transmission and acknowledgement of critical test results. We evaluated the impact of a patient safety initiative with an alert notification system on reducing critical results lacking documented communication, and assessed potential overuse of the alerting system for communicating results. We implemented an alert notification system-Alert Notification of Critical Results (ANCR)-in January 2010. We reviewed radiology reports finalised in 2009-2014 which lacked documented communication between the radiologist and another care provider, and assessed the impact of ANCR on the proportion of such reports with critical findings, using trend analysis over 10 semiannual time periods. To evaluate potential overuse of ANCR, we assessed the proportion of reports with non-critical results among provider-communicated reports. The proportion of reports with critical results among reports without documented communication decreased significantly over 4 years (2009-2014) from 0.19 to 0.05 (pcommunicated reports with non-critical results remained unchanged over time before and after ANCR implementation (0.20 to 0.15, p=0.45, Cochran-Armitage trend test). A patient safety initiative with an alert notification system reduced the proportion of critical results among reports lacking documented communication between care providers. We observed no change in documented communication of non-critical results, suggesting the system did not promote overuse. Future studies are needed to evaluate whether such systems prevent subsequent patient harm. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Project W-211, initial tank retrieval systems, retrieval control system software configuration management plan

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

This Software Configuration Management Plan (SCMP) provides the instructions for change control of the W-211 Project, Retrieval Control System (RCS) software after initial approval/release but prior to the transfer of custody to the waste tank operations contractor. This plan applies to the W-211 system software developed by the project, consisting of the computer human-machine interface (HMI) and programmable logic controller (PLC) software source and executable code, for production use by the waste tank operations contractor. The plan encompasses that portion of the W-211 RCS software represented on project-specific AUTOCAD drawings that are released as part of the C1 definitive design package (these drawings are identified on the drawing list associated with each C-1 package), and the associated software code. Implementation of the plan is required for formal acceptance testing and production release. The software configuration management plan does not apply to reports and data generated by the software except where specifically identified. Control of information produced by the software once it has been transferred for operation is the responsibility of the receiving organization

Operation of the tokamak fusion test reactor tritium systems during initial tritium experiments

International Nuclear Information System (INIS)

Anderson, J.L.; Gentile, C.; Kalish, M.; Kamperschroer, J.; Kozub, T.; LaMarche, P.; Murray, H.; Nagy, A.; Raftopoulos, S.; Rossmassler, R.; Sissingh, R.; Swanson, J.; Tulipano, F.; Viola, M.; Voorhees, D.; Walters, R.T.

1995-01-01

The high power D-T experiments on the tokamak fusion test reactor (TFTR) at the Princeton Plasma Physics Laboratory commenced in November 1993. During initial operation of the tritium systems a number of start-up problems surfaced and had to be corrected. These were corrected through a series of system modifications and upgrades and by repair of failed or inadequate components. Even as these operational concerns were being addressed, the tritium systems continued to support D-T operations on the tokamak. During the first six months of D-T operations more than 107kCi of tritium were processed successfully by the tritium systems. D-T experiments conducted at TFTR during this period provided significant new data. Fusion power in excess of 9MW was achieved in May 1994. This paper describes some of the early start-up issues, and reports on the operation of the tritium system and the tritium tracking and accounting system during the early phase of TFTR D-T experiments. (orig.)

SP-100 initial startup and restart control strategy

International Nuclear Information System (INIS)

Halfen, F.J.; Wong, K.K.; Switick, D.M.; Shukla, J.N.

1992-01-01

This paper reports that recent Generic Flight System (GFS) updates have necessitated revisions in the initial startup and restart control strategies. The design changes that have had the most impact on the control strategies are the addition of the Auxiliary Cooling and Thaw (ACT) system for preheating the lithium filled components, changes in the reactivity worths of the reflectors and safety-rods such that initial cold criticality is achieved with only a small amount of reflector movement following the withdrawal of the safety-rods, and the removal of the scram function from the reflectors. Revised control and operating strategies have been developed and tested using the SP-100 dynamic simulation model, ARIES-GFS. The change in the total reactivity worths of the reflectors and safety-rods has eliminated the need for the use of fast and slow reflector drive speeds during the initial on-orbit approach to criticality. The relatively fast removal of the safety-rods results in a near-critical condition so that the use of slow moving (single speed) reflector drives does not add significant time to achieve full power for the initial startup. The use of the ACT system (with its NaK trace-lines for preheating and auxiliary cooling) affects the main Thermoelectric Electro-Magnetic (TEM) pump startup and the time after a shutdown before freezing occurs in the main heat transfer systems

Defense Acquisition Initiatives Review: An Assessment of Extant Initiatives

National Research Council Canada - National Science Library

Porter, Gene; Berteau, David; Christle, Gary; Mandelbaum, Jay; Diehl, Richard

2005-01-01

...) to identify and analyze a subset of initiatives that the team finds to have potential for near term management emphasis that could provide visible improvements to the much criticized Defense acquisition system...

42 CFR 433.113 - Reduction of FFP for failure to operate a system and obtain initial approval.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Reduction of FFP for failure to operate a system... ADMINISTRATION Mechanized Claims Processing and Information Retrieval Systems § 433.113 Reduction of FFP for failure to operate a system and obtain initial approval. (a) Except as waived under § 433.130 or 433.131...

What do Patients Want From Their Radiation Oncologist? Initial Results From a Prospective Trial

International Nuclear Information System (INIS)

Bhatnagar, Ajay K.; Land, Stephanie R.; Shogan, Alyson; Rodgers, Edwin E.; Heron, Dwight E.; Flickinger, John C.

2007-01-01

Purpose: To assess patients' initial physician preferences using a newly developed instrument. Methods and Materials: A total of 182 patients with a primary diagnosis of prostate, breast, or lung cancer referred for consultation to University of Pittsburgh Cancer Institute Department of Radiation Oncology enrolled in our institutional review board-approved protocol. All patients completed patient preference instrument surveys before meeting their radiation oncologist. Survey responses to 10 statements were categorized into three groups (agree, neutral, or disagree), and the association of survey responses by cancer site was tested with chi-squared tests. Results: Ninety-nine percent of all patients preferred to be addressed by their first name in encounters with their radiation oncologist. There were significant associations of Item 3 (hand holding) with gender (p = 0.039) and education (p = 0.028). The responses to Item 5, a statement that patients would feel uncomfortable if the radiation oncologist offered to hug them at the end of treatment, was significantly associated with disease site (p < 0.0001). Further analysis was performed for Item 5 and revealed that the male lung cancer patients had a much higher rate of disagreement with Item 5 compared with prostate cancer patients (37% vs. 18%). Conclusions: Results of this study may afford greater insight and foster better understanding of what patients want from their radiation oncologist. For breast, lung, and prostate cancer patients, initial preferences for their radiation oncologist are generally similar, according to this tool. However, there are important difference among cancer sites (and gender) regarding physical contact at the end of treatment

Methodological approaches to conducting pilot and proof tests on reverse-osmosis systems: Results of comparative studies

Science.gov (United States)

Panteleev, A. A.; Bobinkin, V. V.; Larionov, S. Yu.; Ryabchikov, B. E.; Smirnov, V. B.; Shapovalov, D. A.

2017-10-01

When designing large-scale water-treatment plants based on reverse-osmosis systems, it is proposed to conduct experimental-industrial or pilot tests for validated simulation of the operation of the equipment. It is shown that such tests allow establishing efficient operating conditions and characteristics of the plant under design. It is proposed to conduct pilot tests of the reverse-osmosis systems on pilot membrane plants (PMPs) and test membrane plants (TMPs). The results of a comparative experimental study of pilot and test membrane plants are exemplified by simulating the operating parameters of the membrane elements of an industrial plant. It is concluded that the reliability of the data obtained on the TMP may not be sufficient to design industrial water-treatment plants, while the PMPs are capable of providing reliable data that can be used for full-scale simulation of the operation of industrial reverse-osmosis systems. The test membrane plants allow simulation of the operating conditions of individual industrial plant systems; therefore, potential areas of their application are shown. A method for numerical calculation and experimental determination of the true selectivity and the salt passage are proposed. An expression has been derived that describes the functional dependence between the observed and true salt passage. The results of the experiments conducted on a test membrane plant to determine the true value of the salt passage of a reverse-osmosis membrane are exemplified by magnesium sulfate solution at different initial operating parameters. It is shown that the initial content of a particular solution component has a significant effect on the change in the true salt passage of the membrane.

A mixed-methods study of system-level sustainability of evidence-based practices in 12 large-scale implementation initiatives.

Science.gov (United States)

Scudder, Ashley T; Taber-Thomas, Sarah M; Schaffner, Kristen; Pemberton, Joy R; Hunter, Leah; Herschell, Amy D

2017-12-07

In recent decades, evidence-based practices (EBPs) have been broadly promoted in community behavioural health systems in the United States of America, yet reported EBP penetration rates remain low. Determining how to systematically sustain EBPs in complex, multi-level service systems has important implications for public health. This study examined factors impacting the sustainability of parent-child interaction therapy (PCIT) in large-scale initiatives in order to identify potential predictors of sustainment. A mixed-methods approach to data collection was used. Qualitative interviews and quantitative surveys examining sustainability processes and outcomes were completed by participants from 12 large-scale initiatives. Sustainment strategies fell into nine categories, including infrastructure, training, marketing, integration and building partnerships. Strategies involving integration of PCIT into existing practices and quality monitoring predicted sustainment, while financing also emerged as a key factor. The reported factors and strategies impacting sustainability varied across initiatives; however, integration into existing practices, monitoring quality and financing appear central to high levels of sustainability of PCIT in community-based systems. More detailed examination of the progression of specific activities related to these strategies may aide in identifying priorities to include in strategic planning of future large-scale initiatives. ClinicalTrials.gov ID NCT02543359 ; Protocol number PRO12060529.

Some results on stability of difference systems

Directory of Open Access Journals (Sweden)

Xiao-Song Yang

2002-01-01

Full Text Available This paper presents some new results on existence and stability of equilibrium or periodic points for difference systems. First sufficient conditions of existence of asymptotically stable equilibrium point as well as the asymptotic stability of given equilibrium point are given for second order or delay difference systems. Then some similar results on existence of asymptotically stable periodic (equilibrium points to general difference systems are presented.

Kinetics of Waterborne Alkyd/Acrylic Hybrid Resin Free Radical Polymerization by Two Systems of Redox and Thermal Initiators

OpenAIRE

shirin Madadi; ali akbar Yousefi; elham Keshmirizadeh

2012-01-01

Kinetics of radical polymerizations of waterborne alkyd/acrylic hybrid resin via batch mini-emulsion technique was studied using redox initiators (TBHP/Fe2+/EDTA/AsAc  and  TBHP/Fe2+/EDTA/SFS) at relatively low temperatures and thermal initiators (BPO, KPS and AIBN) at higher temperatures to seek the most suitable initiator system. At the end of all reactions the unreacted monomer content was reduced using post-polymerization technique; consequently, leading to increased monomer conversion an...

Report of Committee for JAEA Internationalization Initiative (Translated document)

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-07-15

In global circumstances surrounding nuclear energy, the role expected by the Japan Atomic Energy Agency (JAEA) is becoming increasingly important. JAEA has promoted an initiative for an international hub in order to increase the scientific competitiveness of Japan and make international contributions, by gathering excellent researchers from the entire world with the latest facilities. Also, JAEA has established the 'Committee for JAEA Internationalization Initiative', which will discuss issues such as environmental improvement for accepted foreigners, direction of efforts for internationalization initiative and strategies to improve the current situation. This report mentions the results of the committee's discussion including current issues for the initiative and recommendations for their solution, as well as issues to be discussed in order to enhance international awareness of JAEA staff. The following is the summary of the recommendations for the initiative: Set up local teams that focus on the situation of each site in order to provide detailed support for foreigners from diversified backgrounds. Develop systems for emergency situations to provide information for safety swiftly for foreigners and confirm their safety, in addition to preparing emergency goods. Prepare bilingual documents and systems that foreigners need to use for their work based on importance and frequency of use of such systems and documents. (author)

Report of Committee for JAEA Internationalization Initiative (Translated document)

International Nuclear Information System (INIS)

2013-07-01

In global circumstances surrounding nuclear energy, the role expected by the Japan Atomic Energy Agency (JAEA) is becoming increasingly important. JAEA has promoted an initiative for an international hub in order to increase the scientific competitiveness of Japan and make international contributions, by gathering excellent researchers from the entire world with the latest facilities. Also, JAEA has established the 'Committee for JAEA Internationalization Initiative', which will discuss issues such as environmental improvement for accepted foreigners, direction of efforts for internationalization initiative and strategies to improve the current situation. This report mentions the results of the committee's discussion including current issues for the initiative and recommendations for their solution, as well as issues to be discussed in order to enhance international awareness of JAEA staff. The following is the summary of the recommendations for the initiative: Set up local teams that focus on the situation of each site in order to provide detailed support for foreigners from diversified backgrounds. Develop systems for emergency situations to provide information for safety swiftly for foreigners and confirm their safety, in addition to preparing emergency goods. Prepare bilingual documents and systems that foreigners need to use for their work based on importance and frequency of use of such systems and documents. (author)

Comparison of the initial orthodontic force systems produced by a new lingual bracket system and a straight-wire appliance.

Science.gov (United States)

Fuck, Lars-Michael; Wiechmann, Dirk; Drescher, Dieter

2005-09-01

Over the last few years, lingual appliances have become an established orthodontic treatment technique. Many studies have concentrated on various esthetic aspects, on laboratory and clinical procedures, and on patient comfort and compliance. The orthodontic force systems of these appliances, however, have not yet been investigated. The aim of this study was thus to determine the forces and moments produced by a new lingual bracket system during the leveling phase of orthodontic treatment and to compare those with the corresponding force system of a labial straight-wire appliance. The intra-oral situation of ten patients undergoing orthodontic treatment was replicated in measurement casts fitted with lingual and labial brackets. Special care was taken to precisely reproduce each patient's interbracket geometry. We measured each tooth's force systems as generated by a leveling arch inserted into the lingual and labial brackets. The resulting force systems of both appliances were found to be quite similar with regard to the magnitude of most force and moment components. Only the first molars were subjected to considerably greater single forces with the lingual appliance. Tipping moments were found to be significantly smaller with the lingual technique, whereas the rotational moments were significantly smaller with the labial appliance. All in all we noted significant differences between the two techniques only in certain areas which upon closer examination were distributed over only a few tooth types. The initial force systems produced by the new lingual bracket system proved to be comparable with those delivered by a conventional straight-wire appliance. The actual levels of forces and moments, however, were found in certain cases to be too heavy with both techniques. We therefore recommend the development of leveling wires producing considerably lighter forces and moments.

High Order A-stable Continuous General Linear Methods for Solution of Systems of Initial Value Problems in ODEs

Directory of Open Access Journals (Sweden)

Dauda GuliburYAKUBU

2012-12-01

Full Text Available Accurate solutions to initial value systems of ordinary differential equations may be approximated efficiently by Runge-Kutta methods or linear multistep methods. Each of these has limitations of one sort or another. In this paper we consider, as a middle ground, the derivation of continuous general linear methods for solution of stiff systems of initial value problems in ordinary differential equations. These methods are designed to combine the advantages of both Runge-Kutta and linear multistep methods. Particularly, methods possessing the property of A-stability are identified as promising methods within this large class of general linear methods. We show that the continuous general linear methods are self-starting and have more ability to solve the stiff systems of ordinary differential equations, than the discrete ones. The initial value systems of ordinary differential equations are solved, for instance, without looking for any other method to start the integration process. This desirable feature of the proposed approach leads to obtaining very high accuracy of the solution of the given problem. Illustrative examples are given to demonstrate the novelty and reliability of the methods.

A first glance at the initial ATF experimental results

International Nuclear Information System (INIS)

Carreras, B.A.; Dominguez, N.; Leboeuf, J.N.; Lynch, V.E.; Charlton, L.A.

1989-05-01

In the initial phase of ATF operation, the plasma minor radius and the edge rotational transform were reduced by field errors. This caused an effective change of the magnetic configuration: it improved the stability properties but worsened the equilibrium properties. The threshold for the second stability regime was lowered to β 0 /approximately/ 1.5%. Experimental profile data are compatible with operation in the second stability regime, and the achieved beta values, β 0 /approximately/ 3%, are well beyond the theoretically calculated threshold. Magnetic fluctuation measurements showed the effects of beta self-stabilization. They are in reasonable agreement with the predictions of the theory and support the evidence that ATF has already operated in the second stability regime. 24 refs., 20 figs., 1 tab

A study of the state of the art on the determination of the threshold values of the performance indicators for safety systems and initiating events of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Kang, D. I.; Kim, K. Y.; Hwang, M. J.; Park, J. H.; Ha, J. J

2004-02-01

The threshold values of Korean Institute of Nuclear Safety (KINS) Performance Indicators (PIs)' determining the safety class of initiating events and safety systems can not sufficiently reflect the operating experience and PSA results of domestic NPPs. Therefore, the state of arts on the PI study of domestic and foreign countries is analyzed in order to reflect the operating experience and PSA results of domestic NPPs in the determination of the threshold values of the PIs for safety systems and initiating events of domestic NPPs. We identified the state of arts of PIs through reviewing the objectives and types of WANO, IAEA, NRC, OECD/NEA and domestic PIs, and the technical issues of the threshold values of SECY 99-007 and NUREG-1753. We also, identified the current status of recently developed MSPI (Mitigating System Performance Index) and IIIEI (Integrated Industry Initiating Event Indicator). From this study of the state of the arts on the PIs, we expect that if the NRC's MSPI and a PI similar to NRC's IIIEI would be introduced into the KINS, it is not necessary to determine the threshold values of PIs applied to the safety systems and initiating events of entire domestic NPPs. Otherwise the threshold values of PIs applied to the individual NPP should be developed using PSA models of typical reactor types. For the active development and use of the risk informed PIs for the domestic NPPs, we expect that the system and component reliability analysis and initiating events analysis for the domestic NPPs, MSPI, IIIEI, and PSA requirements for the PIs be further studied.

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

Energy Technology Data Exchange (ETDEWEB)

BRIGGS, S.R.

2000-02-25

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS.

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

International Nuclear Information System (INIS)

BRIGGS, S.R.

2000-01-01

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS

Initiatives to Enhance Primary Care Delivery

Directory of Open Access Journals (Sweden)

Jan L. Losby

2015-01-01

Full Text Available Objectives: Increasing demands on primary care providers have created a need for systems-level initiatives to improve primary care delivery. The purpose of this article is to describe and present outcomes for 2 such initiatives: the Pennsylvania Academy of Family Physicians’ Residency Program Collaborative (RPC and the St Johnsbury Vermont Community Health Team (CHT. Methods: Researchers conducted case studies of the initiatives using mixed methods, including secondary analysis of program and electronic health record data, systematic document review, and interviews. Results: The RPC is a learning collaborative that teaches quality improvement and patient centeredness to primary care providers, residents, clinical support staff, and administrative staff in residency programs. Results show that participation in a higher number of live learning sessions resulted in a significant increase in patient-centered medical home recognition attainment and significant improvements in performance in diabetic process measures including eye examinations (14.3%, P = .004, eye referrals (13.82%, P = .013, foot examinations (15.73%, P = .003, smoking cessation (15.83%, P = .012, and self-management goals (25.45%, P = .001. As a community-clinical linkages model, CHT involves primary care practices, community health workers (CHWs, and community partners. Results suggest that CHT members successfully work together to coordinate comprehensive care for the individuals they serve. Further, individuals exposed to CHWs experienced increased stability in access to health insurance ( P = .001 and prescription drugs ( P = .000 and the need for health education counseling ( P = .000. Conclusion: Findings from this study indicate that these 2 system-level strategies have the promise to improve primary care delivery. Additional research can determine the extent to which these strategies can improve other health outcomes.

42 CFR 476.85 - Conclusive effect of QIO initial denial determinations and changes as a result of DRG validations.

Science.gov (United States)

2010-10-01

... determinations and changes as a result of DRG validations. 476.85 Section 476.85 Public Health CENTERS FOR... denial determinations and changes as a result of DRG validations. A QIO initial denial determination or change as a result of DRG validation is final and binding unless, in accordance with the procedures in...

Interventional C-arm tomosynthesis for vascular imaging: initial results

Science.gov (United States)

Langan, David A.; Claus, Bernhard E. H.; Al Assad, Omar; Trousset, Yves; Riddell, Cyril; Avignon, Gregoire; Solomon, Stephen B.; Lai, Hao; Wang, Xin

2015-03-01

As percutaneous endovascular procedures address more complex and broader disease states, there is an increasing need for intra-procedure 3D vascular imaging. In this paper, we investigate C-Arm 2-axis tomosynthesis ("Tomo") as an alternative to C-Arm Cone Beam Computed Tomography (CBCT) for workflow situations in which the CBCT acquisition may be inconvenient or prohibited. We report on our experience in performing tomosynthesis acquisitions with a digital angiographic imaging system (GE Healthcare Innova 4100 Angiographic Imaging System, Milwaukee, WI). During a tomo acquisition the detector and tube each orbit on a plane above and below the table respectively. The tomo orbit may be circular or elliptical, and the tomographic half-angle in our studies varied from approximately 16 to 28 degrees as a function of orbit period. The trajectory, geometric calibration, and gantry performance are presented. We overview a multi-resolution iterative reconstruction employing compressed sensing techniques to mitigate artifacts associated with incomplete data reconstructions. In this work, we focus on the reconstruction of small high contrast objects such as iodinated vasculature and interventional devices. We evaluate the overall performance of the acquisition and reconstruction through phantom acquisitions and a swine study. Both tomo and comparable CBCT acquisitions were performed during the swine study thereby enabling the use of CBCT as a reference in the evaluation of tomo vascular imaging. We close with a discussion of potential clinical applications for tomo, reflecting on the imaging and workflow results achieved.

Stirling to Flight Initiative

Science.gov (United States)

Hibbard, Kenneth E.; Mason, Lee S.; Ndu, Obi; Smith, Clayton; Withrow, James P.

2016-01-01

NASA has a consistent need for radioisotope power systems (RPS) to enable robotic scientific missions for planetary exploration that has been present for over four decades and will continue into the foreseeable future, as documented in the most recent Planetary Science Decadal Study Report. As RPS have evolved throughout the years, there has also grown a desire for more efficient power systems, allowing NASA to serve as good stewards of the limited plutonium-238 (238Pu), while also supporting the ever-present need to minimize mass and potential impacts to the desired science measurements. In fact, the recent Nuclear Power Assessment Study (NPAS) released in April 2015 resulted in several key conclusion regarding RPS, including affirmation that RPS will be necessary well into the 2030s (at least) and that 238Pu is indeed a precious resource requiring efficient utilization and preservation. Stirling Radioisotope Generators (SRGs) combine a Stirling cycle engine powered by a radioisotope heater unit into a single generator system. Stirling engine technology has been under development at NASA Glenn Research Center (GRC) in partnership with the Department of Energy (DOE) since the 1970's. The most recent design, the 238Pu-fueled Advanced Stirling Radioisotope Generator (ASRG), was offered as part of the NASA Discovery 2010 Announcement of Opportunity (AO). The Step-2 selections for this AO included two ASRG-enabled concepts, the Titan Mare Explorer (TiME) and the Comet Hopper (CHopper), although the only non-nuclear concept, InSight, was ultimately chosen. The DOE's ASRG contract was terminated in 2013. Given that SRGs utilize significantly less 238Pu than traditional Radioisotope Thermoelectric Generators (RTGs) - approximately one quarter of the nuclear fuel, to produce similar electrical power output - they provide a technology worthy of consideration for meeting the aforementioned NASA objectives. NASA's RPS Program Office has recently investigated a new Stirling to

The Effects of information barrier requirements on the trilateral initiative attribute measurement system (AVNG)

International Nuclear Information System (INIS)

MacArthur, D.W.; Langner, D.C.; Whiteson, R.; Wolford, J.K.

2001-01-01

Although the detection techniques used for measuring classified materials are very similar to those used in unclassified measurements, the surrounding packaging is generally very different. If iZ classified item is to be measured, an information barrier is required to protect any classified data acquired. This information barrier must protect the classified information while giving the inspector confidence that the unclassified outputs accurately reflect the classified inputs, Both information barrier and authentication considerations must be considered during all phases of system design and fabrication. One example of such a measurement system is the attribute measurement system (termed the AVNG) designed for the: Trilateral Initiative. We will discuss the integration of information barrier components into this system as well as the effects of an information barrier (including authentication) concerns on the implementation of the detector systems.

Initial experience gained with the balance-group system of the Swiss power supply legislation

International Nuclear Information System (INIS)

Waldner, M.; Rechsteiner, S.

2010-01-01

This article takes a look at the initial experience gained with the Swiss balance-group system. This system was introduced within the framework of Swiss power supply legislation (StromVG - Stromversorgungsgesetz). The balance-group system was considered to be an essential precondition for the implementation of an energy trading business in a liberalised power market. The associated rights and responsibilities and the economic risks involved are discussed in detail. The partners and structures involved in such a balance-group are looked at and basic models for the associated contracts are examined. The relationship between balance-groups and the national power grid Swissgrid are discussed

Kinetics of Vinyl Polymerization of Methyl Methacrylate Initiated by Ce(IV-Vanillin Redox System

Directory of Open Access Journals (Sweden)

M. Palanivelu

2012-01-01

Full Text Available The kinetics of polymerization of methyl methacrylate initiated by Ce(IV-Vanillin redox system was studied in aqueous solution of sulfuric acid at 40°C. The rate of polymerization (Rp and the reaction orders with respect to monomer, initiator and ligand have been determined and found to be 1.5, 0.5 and 0.5 respectively. The effect of concentration of sulfuric acid on the polymerization was also studied. The rate of polymerization was found to increase with increasing temperature 30–60°C and decreases at higher temperature (>60°C. The overall activation energy (Ea was found to be 36.7 kJ/mol. A suitable kinetic scheme has been proposed.

Results of initial analyses of the salt (macro) batch 11 Tank 21H qualification samples

Energy Technology Data Exchange (ETDEWEB)

Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-10-23

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 11 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 11 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amounts of solids, or unusual colors. Further sample results will be reported in a future document. This memo satisfies part of Deliverable 3 of the Technical Task Request (TTR).

Learning neuroendoscopy with an exoscope system (video telescopic operating monitor): Early clinical results.

Science.gov (United States)

Parihar, Vijay; Yadav, Y R; Kher, Yatin; Ratre, Shailendra; Sethi, Ashish; Sharma, Dhananjaya

2016-01-01

Steep learning curve is found initially in pure endoscopic procedures. Video telescopic operating monitor (VITOM) is an advance in rigid-lens telescope systems provides an alternative method for learning basics of neuroendoscopy with the help of the familiar principle of microneurosurgery. The aim was to evaluate the clinical utility of VITOM as a learning tool for neuroendoscopy. Video telescopic operating monitor was used 39 cranial and spinal procedures and its utility as a tool for minimally invasive neurosurgery and neuroendoscopy for initial learning curve was studied. Video telescopic operating monitor was used in 25 cranial and 14 spinal procedures. Image quality is comparable to endoscope and microscope. Surgeons comfort improved with VITOM. Frequent repositioning of scope holder and lack of stereopsis is initial limiting factor was compensated for with repeated procedures. Video telescopic operating monitor is found useful to reduce initial learning curve of neuroendoscopy.

Initial Remedial Action Plan for Expanded Bioventing System BX Service Station, Patrick Air Force Base, Florida

National Research Council Canada - National Science Library

1995-01-01

This initial remedial action plan presents the scope for an expanded bioventing system for in situ treatment of fuel-contaminated soils at the BX Service Station at Patrick Air Force Base (AFB), Florida...

Initial Results from the New Stress Map of Texas Project

Science.gov (United States)

Lund Snee, J. E.; Zoback, M. D.

2015-12-01

Modern techniques for characterizing tectonic stress orientation and relative magnitude have been successfully used for more than 35 years. Nevertheless, large areas of North America lack high spatial resolution maps of stress orientation, magnitude, and faulting regime. In Texas, for example, data are foundational elements of attempts to characterize tectonic driving forces, understand hazards associated with induced seismicity, and optimize production of oil, gas, and geothermal resources. This year, we launched the Texas Stress Map project to characterize tectonic stress patterns at higher spatial resolution across Texas and nearby areas. Following a successful effort just completed in Oklahoma, we will evaluate borehole breakouts, drilling-induced tensile fractures, shear wave anisotropy, and earthquake data. The principal data source will be FMI (fullbore formation microimager), UBI (ultrasonic borehole imager), cross-dipole sonic, density, and caliper logs provided by private industry. Earthquake moment tensor solutions from the U.S. Geological Survey, Saint Louis University and other sources will also be used. Our initial focus is on the Permian Basin and Barnett Shale petroleum plays due to the availability of data, but we will expand our analysis across the state as the project progresses. In addition, we hope to eventually apply the higher spatial resolution data coverage to understanding tectonic and geodynamic characteristics of the southwestern United States and northeastern Mexico. Here we present early results from our work to constrain stress orientations and faulting regime in and near Texas, and we also provide a roadmap for the ongoing research.

Equation of material balance for systems of double porosity with layer of initial gas

International Nuclear Information System (INIS)

Niz, Eider; Hidrobo, Eduardo A; Penuela, Gherson; Ordonez, Anibal; Calderon, Zuly H

2004-01-01

The physical complexity associated to naturally fractured reservoirs calls for the use of more robust formulations of the Material-Balance Equation (MBE) for determining the initial hydrocarbon in place and predicting reservoir performance. In this paper, we present an improved version of the dual-porosity MBE for naturally fractured reservoirs, published by Penuela et al. (2001), including the existence of an initial gas phase in the reservoir. Considering that a fractured reservoir may be modeled either using different properties for each porous medium or with average values for the total system, two solution techniques based on each of these assumptions are proposed. Convenient arrangements of the equation allow us to estimate not only the original oil and gas volumes but also the relative storage capacity of the porous media (fractures and matrix) and the compressibility for the fractured and total systems. The new equation can be applied to a broader range of reservoirs due to its more general character. The consistency of the expression proposed has been tested with a set of synthetic models exhibiting different storage capacity in the fractures

Quality initiatives: improving patient flow for a bone densitometry practice: results from a Mayo Clinic radiology quality initiative.

Science.gov (United States)

Aakre, Kenneth T; Valley, Timothy B; O'Connor, Michael K

2010-03-01

Lean Six Sigma process improvement methodologies have been used in manufacturing for some time. However, Lean Six Sigma process improvement methodologies also are applicable to radiology as a way to identify opportunities for improvement in patient care delivery settings. A multidisciplinary team of physicians and staff conducted a 100-day quality improvement project with the guidance of a quality advisor. By using the framework of DMAIC (define, measure, analyze, improve, and control), time studies were performed for all aspects of patient and technologist involvement. From these studies, value stream maps for the current state and for the future were developed, and tests of change were implemented. Comprehensive value stream maps showed that before implementation of process changes, an average time of 20.95 minutes was required for completion of a bone densitometry study. Two process changes (ie, tests of change) were undertaken. First, the location for completion of a patient assessment form was moved from inside the imaging room to the waiting area, enabling patients to complete the form while waiting for the technologist. Second, the patient was instructed to sit in a waiting area immediately outside the imaging rooms, rather than in the main reception area, which is far removed from the imaging area. Realignment of these process steps, with reduced technologist travel distances, resulted in a 3-minute average decrease in the patient cycle time. This represented a 15% reduction in the initial patient cycle time with no change in staff or costs. Radiology process improvement projects can yield positive results despite small incremental changes.

Final Report on the Study of the Impact of the Statewide Systemic Initiatives. Lessons Learned about Designing, Implementing, and Evaluating Statewide Systemic Reform. WCER Working Paper No. 2003-12

Science.gov (United States)

Heck, Daniel J.; Weiss, Iris R.; Boyd, Sally E.; Howard, Michael N.; Supovitz, Jonathan A.

2003-01-01

This document represents the first of two volumes presented in "Study of the Impact of the Statewide Systemic Initiatives Program" (Norman L. Webb and Iris R. Weiss). In an effort to evaluate the impact of the Statewide Systemic Initiatives (SSIs) on student achievement and the lessons that could be learned from the National Science…

αII Spectrin Forms a Periodic Cytoskeleton at the Axon Initial Segment and Is Required for Nervous System Function.

Science.gov (United States)

Huang, Claire Yu-Mei; Zhang, Chuansheng; Ho, Tammy Szu-Yu; Oses-Prieto, Juan; Burlingame, Alma L; Lalonde, Joshua; Noebels, Jeffrey L; Leterrier, Christophe; Rasband, Matthew N

2017-11-22

Spectrins form a submembranous cytoskeleton proposed to confer strength and flexibility to neurons and to participate in ion channel clustering at axon initial segments (AIS) and nodes of Ranvier. Neuronal spectrin cytoskeletons consist of diverse β subunits and αII spectrin. Although αII spectrin is found in neurons in both axonal and somatodendritic domains, using proteomics, biochemistry, and superresolution microscopy, we show that αII and βIV spectrin interact and form a periodic AIS cytoskeleton. To determine the role of spectrins in the nervous system, we generated Sptan1 f/f mice for deletion of CNS αII spectrin. We analyzed αII spectrin-deficient mice of both sexes and found that loss of αII spectrin causes profound reductions in all β spectrins. αII spectrin-deficient mice die before 1 month of age and have disrupted AIS and many other neurological impairments including seizures, disrupted cortical lamination, and widespread neurodegeneration. These results demonstrate the importance of the spectrin cytoskeleton both at the AIS and throughout the nervous system. SIGNIFICANCE STATEMENT Spectrin cytoskeletons play diverse roles in neurons, including assembly of excitable domains such as the axon initial segment (AIS) and nodes of Ranvier. However, the molecular composition and structure of these cytoskeletons remain poorly understood. Here, we show that αII spectrin partners with βIV spectrin to form a periodic cytoskeleton at the AIS. Using a new αII spectrin conditional knock-out mouse, we show that αII spectrin is required for AIS assembly, neuronal excitability, cortical lamination, and to protect against neurodegeneration. These results demonstrate the broad importance of spectrin cytoskeletons for nervous system function and development and have important implications for nervous system injuries and diseases because disruption of the spectrin cytoskeleton is a common molecular pathology. Copyright © 2017 the authors 0270-6474/17/3711311-12$15.00/0.

Lay persons alerted by mobile application system initiate earlier cardio-pulmonary resuscitation: A comparison with SMS-based system notification.

Science.gov (United States)

Caputo, Maria Luce; Muschietti, Sandro; Burkart, Roman; Benvenuti, Claudio; Conte, Giulio; Regoli, François; Mauri, Romano; Klersy, Catherine; Moccetti, Tiziano; Auricchio, Angelo

2017-05-01

We compared the time to initiation of cardiopulmonary resuscitation (CPR) by lay responders and/or first responders alerted either via Short Message Service (SMS) or by using a mobile application-based alert system (APP). The Ticino Registry of Cardiac Arrest collects all data about out-of-hospital cardiac arrests (OHCAs) occurring in the Canton of Ticino. At the time of a bystander's call, the EMS dispatcher sends one ambulance and alerts the first-responders network made up of police officers or fire brigade equipped with an automatic external defibrillator, the so called "traditional" first responders, and - if the scene was considered safe - lay responders as well. We evaluated the time from call to arrival of traditional first responders and/or lay responders when alerted either via SMS or the new developed mobile APP. Over the study period 593 OHCAs have occurred. Notification to the first responders network was sent via SMS in 198 cases and via mobile APP in 134 cases. Median time to first responder/lay responder arrival on scene was significantly reduced by the APP-based system (3.5 [2.8-5.2]) compared to the SMS-based system (5.6 [4.2-8.5] min, p 0.0001). The proportion of lay responders arriving first on the scene significantly increased (70% vs. 15%, play responder determined a higher survival rate. The mobile APP system is highly efficient in the recruitment of first responders, significantly reducing the time to the initiation of CPR thus increasing survival rates. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Initial Surgical Experience with Aortic Valve Repair: Clinical and Echocardiographic Results

Directory of Open Access Journals (Sweden)

Francisco Diniz Affonso da Costa

Full Text Available Abstract Introduction: Due to late complications associated with the use of conventional prosthetic heart valves, several centers have advocated aortic valve repair and/or valve sparing aortic root replacement for patients with aortic valve insufficiency, in order to enhance late survival and minimize adverse postoperative events. Methods: From March/2012 thru March 2015, 37 patients consecutively underwent conservative operations of the aortic valve and/or aortic root. Mean age was 48±16 years and 81% were males. The aortic valve was bicuspid in 54% and tricuspid in the remaining. All were operated with the aid of intraoperative transesophageal echocardiography. Surgical techniques consisted of replacing the aortic root with a Dacron graft whenever it was dilated or aneurysmatic, using either the remodeling or the reimplantation technique, besides correcting leaflet prolapse when present. Patients were sequentially evaluated with clinical and echocardiographic studies and mean follow-up time was 16±5 months. Results: Thirty-day mortality was 2.7%. In addition there were two late deaths, with late survival being 85% (CI 95% - 68%-95% at two years. Two patients were reoperated due to primary structural valve failure. Freedom from reoperation or from primary structural valve failure was 90% (CI 95% - 66%-97% and 91% (CI 95% - 69%-97% at 2 years, respectively. During clinical follow-up up to 3 years, there were no cases of thromboembolism, hemorrhage or endocarditis. Conclusions: Although this represents an initial series, these data demonstrates that aortic valve repair and/or valve sparing aortic root surgery can be performed with satisfactory immediate and short-term results.

Initiating Event Analysis of a Lithium Fluoride Thorium Reactor

Science.gov (United States)

Geraci, Nicholas Charles

The primary purpose of this study is to perform an Initiating Event Analysis for a Lithium Fluoride Thorium Reactor (LFTR) as the first step of a Probabilistic Safety Assessment (PSA). The major objective of the research is to compile a list of key initiating events capable of resulting in failure of safety systems and release of radioactive material from the LFTR. Due to the complex interactions between engineering design, component reliability and human reliability, probabilistic safety assessments are most useful when the scope is limited to a single reactor plant. Thus, this thesis will study the LFTR design proposed by Flibe Energy. An October 2015 Electric Power Research Institute report on the Flibe Energy LFTR asked "what-if?" questions of subject matter experts and compiled a list of key hazards with the most significant consequences to the safety or integrity of the LFTR. The potential exists for unforeseen hazards to pose additional risk for the LFTR, but the scope of this thesis is limited to evaluation of those key hazards already identified by Flibe Energy. These key hazards are the starting point for the Initiating Event Analysis performed in this thesis. Engineering evaluation and technical study of the plant using a literature review and comparison to reference technology revealed four hazards with high potential to cause reactor core damage. To determine the initiating events resulting in realization of these four hazards, reference was made to previous PSAs and existing NRC and EPRI initiating event lists. Finally, fault tree and event tree analyses were conducted, completing the logical classification of initiating events. Results are qualitative as opposed to quantitative due to the early stages of system design descriptions and lack of operating experience or data for the LFTR. In summary, this thesis analyzes initiating events using previous research and inductive and deductive reasoning through traditional risk management techniques to

Initial results in SST-1 after up-gradation

Science.gov (United States)

Pradhan, S.; Khan, Z.; Tanna, V. L.; Prasad, U.; Paravastu, Y.; Raval, D. C.; Masand, H.; Kumar, Aveg; Dhongde, J. R.; Jana, S.; Kakati, B.; Patel, K. B.; Bhandarkar, M. K.; Shukla, B. K.; Ghosh, D.; Patel, H. S.; Parekh, T. J.; Mansuri, I. A.; Dhanani, K. R.; Varadharajulu, A.; Khristi, Y. S.; Biswas, P.; Gupta, C. N.; George, S.; Semwal, P.; Sharma, D. K.; Gulati, H. K.; Mahajan, K.; Praghi, B. R.; Banaudha, M.; Makwana, A. R.; Chudasma, H. H.; Kumar, M.; Manchanda, R.; Joisa, Y. S.; Asudani, K.; Pandya, S. N.; Pathak, S. K.; Banerjee, S.; Patel, P. J.; Santra, P.; Pathan, F. S.; Chauhan, P. K.; Khan, M. S.; Thankey, P. L.; Prakash, A.; Panchal, P. N.; Panchal, R. N.; Patel, R. J.; Mahsuria, G. I.; Sonara, D. P.; Patel, K. M.; Jayaswal, S. P.; Sharma, M.; Patel, J. C.; Varmora, P.; Srikanth, G. L. N.; Christian, D. R.; Garg, A.; Bairagi, N.; Babu, G. R.; Panchal, A. G.; Vora, M. M.; Singh, A. K.; Sharma, R.; Nimavat, H. D.; Shah, P. R.; Purwar, G.; Raval, T. Y.; Sharma, A. L.; Ojha, A.; Kumar, S.; Ramaiya, N. K.; Siju, V.; Gopalakrishna, M. V.; Kumar, A.; Sharma, P. K.; Atrey, P. K.; Kulkarni, SV; Ambulkar, K. K.; Parmar, P. R.; Thakur, A. L.; Raval, J. V.; Purohit, S.; Mishra, P. K.; Adhiya, A. N.; Nagora, U. C.; Thomas, J.; Chaudhari, V. K.; Patel, K. G.; Dalakoti, S.; Virani, C. G.; Gupta, S.; Kumar, Ajay; Chaudhari, B.; Kaur, R.; Srinivasan, R.; Raju, D.; Kanabar, D. H.; Jha, R.; Das, A.; Bora, D.

2017-04-01

SST-1 Tokamak has recently completed the 1st phase of up-gradation with successful installation and integration of all its First Wall components. The First Wall of SST-1 comprises of ∼ 3800 high heat flux compatible graphite tiles being assembled and installed on 132 CuCrZr heat sink back plates engraved with ∼ 4 km of leak tight baking and cooling channels in five major sub groups equipped with ∼ 400 sensors and weighing ∼ 6000 kg in total in thirteen isolated galvanic and six isolated hydraulic circuits. The phase-1 up-gradation spectrum also includes addition of Supersonic Molecular Beam Injection (SMBI) both on the in-board and out-board side, installation of fast reciprocating probes, adding some edge plasma probe diagnostics in the SOL region, installation and integration of segmented and up-down symmetric radial coils aiding/controlling plasma rotations, introduction of plasma position feedback and density controls etc. Post phase-I up-gradation spanning from Nov 2014 till June 2016, initial plasma experiments in up-graded SST-1 have begun since Aug 2016 after a brief engineering validation period in SST-1. The first experiments in SST-1 have revealed interesting aspects on the ‘eddy currents in the First Wall support structures’ influencing the ‘magnetic Null evolution dynamics’ and the subsequent plasma start-up characteristics after the ECH pre-ionization, the influence of the first walls on the ‘field errors’ and the resulting locked modes observed, the magnetic index influencing the evolution of the equilibrium of the plasma column, low density supra-thermal electron induced discharges and normal ohmic discharges etc. Presently; repeatable ohmic discharges regimes in SST-1 having plasma currents in excess of 65 KA (qa ∼ 3.8, BT = 1.5 T) with a current ramp rates ∼ 1.2 MA/s over a duration of ∼ 300 ms with line averaged densities ∼ 0.8 × 1019 and temperatures ∼ 200 eV with copious MHD signatures have been experimentally

Hanford tanks initiative plan

International Nuclear Information System (INIS)

McKinney, K.E.

1997-01-01

Abstract: The Hanford Tanks Initiative (HTI) is a five-year project resulting from the technical and financial partnership of the U.S. Department of Energy's Office of Waste Management (EM-30) and Office of Science and Technology Development (EM-50). The HTI project accelerates activities to gain key technical, cost performance, and regulatory information on two high-level waste tanks. The HTI will provide a basis for design and regulatory decisions affecting the remainder of the Tank Waste Remediation System's tank waste retrieval Program

Initial Business Case Analysis of Two Integrated Heat Pump HVAC Systems for Near-Zero-Energy Homes

Energy Technology Data Exchange (ETDEWEB)

Baxter, Van D [ORNL

2006-11-01

The long range strategic goal of the Department of Energy's Building Technologies (DOE/BT) Program is to create, by 2020, technologies and design approaches that enable the construction of net-zero energy homes at low incremental cost (DOE/BT 2005). A net zero energy home (NZEH) is a residential building with greatly reduced needs for energy through efficiency gains, with the balance of energy needs supplied by renewable technologies. While initially focused on new construction, these technologies and design approaches are intended to have application to buildings constructed before 2020 as well resulting in substantial reduction in energy use for all building types and ages. DOE/BT's Emerging Technologies (ET) team is working to support this strategic goal by identifying and developing advanced heating, ventilating, air-conditioning, and water heating (HVAC/WH) technology options applicable to NZEHs. Although the energy efficiency of heating, ventilating, and air-conditioning (HVAC) equipment has increased substantially in recent years, new approaches are needed to continue this trend. Dramatic efficiency improvements are necessary to enable progress toward the NZEH goals, and will require a radical rethinking of opportunities to improve system performance. The large reductions in HVAC energy consumption necessary to support the NZEH goals require a systems-oriented analysis approach that characterizes each element of energy consumption, identifies alternatives, and determines the most cost-effective combination of options. In particular, HVAC equipment must be developed that addresses the range of special needs of NZEH applications in the areas of reduced HVAC and water heating energy use, humidity control, ventilation, uniform comfort, and ease of zoning. In FY05 ORNL conducted an initial Stage 1 (Applied Research) scoping assessment of HVAC/WH systems options for future NZEHs to help DOE/BT identify and prioritize alternative approaches for further

[Development of Non-Arteritic Anterior Ischaemic Optic Neuropathy in the Initially Unaffected Fellow Eye in Patients Treated with Systemic Corticosteroids].

Science.gov (United States)

Pahor, Artur; Pahor, Dusica

2017-11-01

Background The objective of this prospective pilot study was to evaluate the results of systemic corticosteroid therapy in patient with non-arteritic anterior ischaemic neuropathy of the optical nerve (NAION) for an observation period of one year and to measure the NAION incidence in the initially healthy contralateral eye of these patients. Patients and Methods All patients diagnosed with acute NAION who were admitted to our ward during 2014 and who fulfilled all inclusion criteria for systemic corticosteroid therapy were included in the study. The inclusion criteria were corrected visual acuity of 0.3 or less and duration of illness of less than 2 weeks. All patients were examined by a rheumatologist and given a complete ophthalmological examination, including fluorescein angiography and examination of the visual field. Only 3 of the 23 patients fulfilled our inclusion criteria for corticoid treatment and were then treated. 10 patients served as controls. The treatment plan started with an initial dose of 80 mg prednisolone during the first two weeks. The dose was then tapered over 3 to 4 months. Results The mean best corrected visual acuity on admission was 0.12 and 0.35 after one year. The mean duration of treatment was 3.3 months. Treatment was discontinued after 5 to 6 months or 8 to 9 months after the initial examination. All patients then developed NAION on the contralateral eye. The mean visual acuity on the contralateral eye was 0.73. After 4 month follow-up, the visual acuity in two patients had decreased to 1.0 and in one patient was reduced from 0.8 to 0.4. No steroid treatment was initiated for the contralateral eye. No NAION was found in the contralateral eye in the control group. Conclusion Corticosteroid treatment improved vision in all patients with NAION in comparison with the untreated contralateral eye. In a single patient, visual acuity decreased in the contralateral eye. Our study confirmed that corticosteroid treatment may be a

Moving State Marine SINS Initial Alignment Based on High Degree CKF

Directory of Open Access Journals (Sweden)

Yong-Gang Zhang

2014-01-01

Full Text Available A new moving state marine initial alignment method of strap-down inertial navigation system (SINS is proposed based on high-degree cubature Kalman filter (CKF, which can capture higher order Taylor expansion terms of nonlinear alignment model than the existing third-degree CKF, unscented Kalman filter and central difference Kalman filter, and improve the accuracy of initial alignment under large heading misalignment angle condition. Simulation results show the efficiency and advantage of the proposed initial alignment method as compared with existing initial alignment methods for the moving state SINS initial alignment with large heading misalignment angle.

Munitions having an insensitive detonator system for initiating large failure diameter explosives

Science.gov (United States)

Perry, III, William Leroy

2015-08-04

A munition according to a preferred embodiment can include a detonator system having a detonator that is selectively coupled to a microwave source that functions to selectively prime, activate, initiate, and/or sensitize an insensitive explosive material for detonation. The preferred detonator can include an explosive cavity having a barrier within which an insensitive explosive material is disposed and a waveguide coupled to the explosive cavity. The preferred system can further include a microwave source coupled to the waveguide such that microwaves enter the explosive cavity and impinge on the insensitive explosive material to sensitize the explosive material for detonation. In use the preferred embodiments permit the deployment and use of munitions that are maintained in an insensitive state until the actual time of use, thereby substantially preventing unauthorized or unintended detonation thereof.

Dependence of sports results on data of physical development, morphofunctional and special power preparedness of weight-lifters at the stage of initial preparation

Directory of Open Access Journals (Sweden)

Eugene Bugaev

2016-12-01

Full Text Available Purpose: the establishment of nature of the interrelation between sports results of weight-lifters and level of their special physical and morphofunctional preparedness. Material & Methods: 48 sportsmen of group of initial preparation of the first year of training were involved to the experiment. The research was conducted on the basis of the chair of weightlifting and boxing of Kharkov state academy of physical culture and CYSS “HTZ”. Results: the correlation between indicators of morphofunctional, high-speed and power and special (competitive preparedness of weight-lifters is revealed at the stage of initial preparation. The conducted research shows that the result of competitive exercises of the sportsmen, specializing in weightlifting at the stage of initial preparation, depends on power and high-speed and power preparedness. Conclusions: it is established that the correlation between results of competitive exercises and jumps uphill from the place, in length from the place, run on 30 m can demonstrate the interrelation of power and high-speed and power preparedness of the sportsmen, specializing in weightlifting at the stage of initial preparation.

The Spanish system for the radiological surveillance and control of scrap and the products resulting from its processing

International Nuclear Information System (INIS)

Gil, E.

2001-01-01

Despite the fact that the use of radiation technologies has always been subjected to strict controls in most countries, the presence of radioactive materials in scrap has been detected relatively often in recent years. This has led to the implementation of a series of international initiatives aimed at detecting and preventing illicit international trafficking with radioactive material, intentional or otherwise. The Spanish iron and steel industry is one of the most important industrial sectors in the country, and depends to a large extent on the importing of a significant proportion of the scrap its uses as raw material. Experience has shown that that countries that import large quantities of scrap should complement the aforementioned international initiatives with others of national scope, in order to reduce the risks arising from the presence of radioactive material in scrap. In this context, the Spanish radiological protection authorities, along with the business associations involved in the metal recovery and smelting industry, have established a national system for the radiological surveillance and control of scrap and of the products resulting from its processing. The system consists of a set of legal bases, the installation of specific radiological surveillance equipment and the enhancement of other general purpose equipment that existed prior to these initiatives, the development of radiological training and information plans for the professionals involved in the metal recovery and smelting sectors and improvement to the national radiological emergency response system. (author)

The Young Solar Analogs Project: Initial Photometric Results

Science.gov (United States)

Saken, Jon M.; Gray, R. O.; Corbally, C. J.

2013-06-01

Since 2007 we have been conducting spectroscopic monitoring of the Ca II H & K lines and G-band for a sample of 31 YSAs in order to better understand their activity cycles and variations, as well as the effects of young stars on their solar systems. The targets cover the spectral range of stars most likely to contain Earth analogs, F8-K2, and a broad enough range of ages, 0.3 Gyr - 1.5 Gyr, to investigate how activity level changes with stellar age. These studies are already showing possible evidence for activity cycles, large variations in starspot activity, and flaring events. In order to obtain a more complete picture of the nature of the stars' activity and examine the correlations between stellar brightness and chromospheric activity, we have started a complimentary campaign of photometric monitoring of these targets in Johnson B, V, and R, Stromgren v and H-alpha, with the use of a small robotic telescope dedicated to this project. This poster will present some results from the first year of photometric monitoring, focusing on the correlations between the photometric bands, and between the photometric and spectroscopic data, as well as an investigation of short-term (1-2 minutes) spectroscopic variations using data obtained earlier this year on the 1.8 m Vatican Advanced Technology Telescope (VATT).

Scientific investigation plan for initial engineered barrier system field tests

International Nuclear Information System (INIS)

Wunan Lin.

1993-02-01

The purpose of this Scientific Investigation Plan (SIP) is to describe tests known as Initial Engineered Barrier System Field Tests (IEBSFT) and identified by Work Breakdown Structure as WBS 1.2.2.2.4. The IEBSFT are precursors to the Engineered Barrier System Field Test (EBSFT), WBS 1.2.2.2.4, to be conducted in the Exploratory Study Facility (ESF) at Yucca Mountain. The EBSFT and IEBSFT are designed to provide information on the interaction between waste packages (simulated by heated containers) and the surrounding rock mass, its vadose water, and infiltrated water. Heater assemblies will be installed in drifts or boreholes openings and heated to measure moisture movement during heat-up and subsequent cool-down of the rock mass. In some of the tests, infiltration of water into the heated rock mass will be studied. Throughout the heating and cooling cycle, instruments installed in the rock will monitor such parameters as temperature, moisture content, concentration of some chemical species, and stress and strain. Rock permeability measurements, rock and fluid (water and gas) sampling, and fracture pattern measurements will also be made before and after the test

Initial results from the rebuilt EXTRAP T2R RFP device

Science.gov (United States)

Brunsell, P. R.; Bergsåker, H.; Cecconello, M.; Drake, J. R.; Gravestijn, R. M.; Hedqvist\\ad{2 }, A.; Malmberg, J.-A.

2001-11-01

The EXTRAP T2R thin shell reversed-field pinch (RFP) device has recently resumed operation after a major rebuild including the replacement of the graphite armour with molybdenum limiters, a fourfold increase of the shell time constant, and the replacement of the helical coil used for the toroidal field with a conventional solenoid-type coil. Wall-conditioning using hydrogen glow discharge cleaning was instrumental for successful RFP operation. Carbon was permanently removed from the walls during the first week of operation. The initial results from RFP operation with relatively low plasma currents in the range Ip = 70-100 kA are reported. RFP discharges are sustained for more than three shell times. Significant improvements in plasma parameters are observed, compared to operation before the rebuild. There is a substantial reduction in the carbon impurity level. The electron density behaviour is more shot-to-shot reproducible. The typical density is ne = 0.5-1×1019 m-3. Monitors of Hα line radiation indicate that the plasma wall interaction is more toroidally symmetric and that there is less transient gas release from the wall. The minimum loop voltage is in the range Vt = 28-35 V, corresponding to a reduction by a factor of two to three compared to the value before the rebuild.

Communications with Mars During Periods of Solar Conjunction: Initial Study Results

Science.gov (United States)

Morabito, D.; Hastrup, R.

2001-07-01

During the initial phase of the human exploration of Mars, a reliable communications link to and from Earth will be required. The direct link can easily be maintained during most of the 780-day Earth-Mars synodic period. However, during periods in which the direct Earth-Mars link encounters increased intervening charged particles during superior solar conjunctions of Mars, the resultant effects are expected to corrupt the data signals to varying degrees. The purpose of this article is to explore possible strategies, provide recommendations, and identify options for communicating over this link during periods of solar conjunctions. A significant improvement in telemetry data return can be realized by using the higher frequency 32 GHz (Ka-band), which is less susceptible to solar effects. During the era of the onset of probable human exploration of Mars, six superior conjunctions were identified from 2015 to 2026. For five of these six conjunctions, where the signal source is not occulted by the disk of the Sun, continuous communications with Mars should be achievable. Only during the superior conjunction of 2023 is the signal source at Mars expected to lie behind the disk of the Sun for about one day and within two solar radii (0. 5 deg) for about three days.

Structural Basis of Mitochondrial Transcription Initiation.

Science.gov (United States)

Hillen, Hauke S; Morozov, Yaroslav I; Sarfallah, Azadeh; Temiakov, Dmitry; Cramer, Patrick

2017-11-16

Transcription in human mitochondria is driven by a single-subunit, factor-dependent RNA polymerase (mtRNAP). Despite its critical role in both expression and replication of the mitochondrial genome, transcription initiation by mtRNAP remains poorly understood. Here, we report crystal structures of human mitochondrial transcription initiation complexes assembled on both light and heavy strand promoters. The structures reveal how transcription factors TFAM and TFB2M assist mtRNAP to achieve promoter-dependent initiation. TFAM tethers the N-terminal region of mtRNAP to recruit the polymerase to the promoter whereas TFB2M induces structural changes in mtRNAP to enable promoter opening and trapping of the DNA non-template strand. Structural comparisons demonstrate that the initiation mechanism in mitochondria is distinct from that in the well-studied nuclear, bacterial, or bacteriophage transcription systems but that similarities are found on the topological and conceptual level. These results provide a framework for studying the regulation of gene expression and DNA replication in mitochondria. Copyright © 2017 Elsevier Inc. All rights reserved.

Global health initiative investments and health systems strengthening: a content analysis of global fund investments.

Science.gov (United States)

Warren, Ashley E; Wyss, Kaspar; Shakarishvili, George; Atun, Rifat; de Savigny, Don

2013-07-26

Millions of dollars are invested annually under the umbrella of national health systems strengthening. Global health initiatives provide funding for low- and middle-income countries through disease-oriented programmes while maintaining that the interventions simultaneously strengthen systems. However, it is as yet unclear which, and to what extent, system-level interventions are being funded by these initiatives, nor is it clear how much funding they allocate to disease-specific activities - through conventional 'vertical-programming' approach. Such funding can be channelled to one or more of the health system building blocks while targeting disease(s) or explicitly to system-wide activities. We operationalized the World Health Organization health system framework of the six building blocks to conduct a detailed assessment of Global Fund health system investments. Our application of this framework framework provides a comprehensive quantification of system-level interventions. We applied this systematically to a random subset of 52 of the 139 grants funded in Round 8 of the Global Fund to Fight AIDS, Tuberculosis and Malaria (totalling approximately US$1 billion). According to the analysis, 37% (US$ 362 million) of the Global Fund Round 8 funding was allocated to health systems strengthening. Of that, 38% (US$ 139 million) was for generic system-level interventions, rather than disease-specific system support. Around 82% of health systems strengthening funding (US$ 296 million) was allocated to service delivery, human resources, and medicines & technology, and within each of these to two to three interventions. Governance, financing, and information building blocks received relatively low funding. This study shows that a substantial portion of Global Fund's Round 8 funds was devoted to health systems strengthening. Dramatic skewing among the health system building blocks suggests opportunities for more balanced investments with regard to governance, financing, and

Main Experimental Results of ISTC-1606 for Recycling and Transmutation in Molten Salt Systems

Energy Technology Data Exchange (ETDEWEB)

Ignatiev, Victor; Feynberg, Olga; Merzlyakov, Aleksandr; Surenkov, Aleksandr [Russian Research Center - Kurchatov Institute, Kurchatov sq. 1, Moscow, RF, 123182 (Russian Federation); Subbotin, Vladimir; Zakirov, Raul; Toropov, Andrey; Panov, Aleksandr [Russian Federal Nuclear Center - Institute of Technical Physics, Snezhinsk (Russian Federation); Afonichkin, Valery [Institute of High-Temperature Electrochemistry, Ekaterinburg (Russian Federation)

2008-07-01

To examine and demonstrate the feasibility of molten salt reactors (MSR) to reduce long lived waste toxicity and to produce efficiently electricity in closed fuel cycle, some national and international studies were initiated last years. In this paper main focus is placed on experimental evaluation of single stream Molten Salt Actinide Recycler and Transmuter (MOSART) system fuelled with different compositions of plutonium plus minor actinide trifluoride (AnF{sub 3}) from LWR spent nuclear fuel without U-Th support. This paper summarizes main experimental results of ISTC-1606 related to physical and chemical properties of fuel salt, container materials for fuel circuit, and fuel salt clean up of MOSART system. As result of ISTC-1606 studies claim is made, that the {sup 7}Li,Na,Be/F and {sup 7}Li,Be/F solvents selected for primary system appear to resolve main reactor physics, thermal hydraulics, materials compatibility, fuel salt clean up and safety problems as applied to the MOSART concept development. The created experimental facilities and the database on properties of fuel salt mixtures and container materials are used for a choice and improvement fuel salts and coolants for new applications of this high temperature technology for sustainable nuclear power development. (authors)

Main Experimental Results of ISTC-1606 for Recycling and Transmutation in Molten Salt Systems

International Nuclear Information System (INIS)

Ignatiev, Victor; Feynberg, Olga; Merzlyakov, Aleksandr; Surenkov, Aleksandr; Subbotin, Vladimir; Zakirov, Raul; Toropov, Andrey; Panov, Aleksandr; Afonichkin, Valery

2008-01-01

To examine and demonstrate the feasibility of molten salt reactors (MSR) to reduce long lived waste toxicity and to produce efficiently electricity in closed fuel cycle, some national and international studies were initiated last years. In this paper main focus is placed on experimental evaluation of single stream Molten Salt Actinide Recycler and Transmuter (MOSART) system fuelled with different compositions of plutonium plus minor actinide trifluoride (AnF 3 ) from LWR spent nuclear fuel without U-Th support. This paper summarizes main experimental results of ISTC-1606 related to physical and chemical properties of fuel salt, container materials for fuel circuit, and fuel salt clean up of MOSART system. As result of ISTC-1606 studies claim is made, that the 7 Li,Na,Be/F and 7 Li,Be/F solvents selected for primary system appear to resolve main reactor physics, thermal hydraulics, materials compatibility, fuel salt clean up and safety problems as applied to the MOSART concept development. The created experimental facilities and the database on properties of fuel salt mixtures and container materials are used for a choice and improvement fuel salts and coolants for new applications of this high temperature technology for sustainable nuclear power development. (authors)

The Beck Initiative: A Partnership to Implement Cognitive Therapy in a Community Behavioral Health System

Science.gov (United States)

Stirman, Shannon Wiltsey; Buchhofer, Regina; McLaulin, J. Bryce; Evans, Arthur C.; Beck, Aaron T.

2010-01-01

The Beck Initiative is a partnership between researchers and clinicians at a large university and an urban behavioral health managed care system. Both partners share a commitment to ensuring that consumers in the community have access to competently delivered, individualized, evidence-based mental health care and that the providers who serve them have the support they need to deliver high-quality evidence-based treatments. Central features of the program are individualized training and consultation in cognitive therapy for each provider agency and policies to promote the sustainability of the initiative and its continuing evolution to meet the needs of providers and consumers. PMID:19797367

C-Band Airport Surface Communications System Standards Development. Phase II Final Report. Volume 1: Concepts of Use, Initial System Requirements, Architecture, and AeroMACS Design Considerations

Science.gov (United States)

Hall, Edward; Isaacs, James; Henriksen, Steve; Zelkin, Natalie

2011-01-01

This report is provided as part of ITT s NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: New ATM Requirements-Future Communications, C-Band and L-Band Communications Standard Development and was based on direction provided by FAA project-level agreements for New ATM Requirements-Future Communications. Task 7 included two subtasks. Subtask 7-1 addressed C-band (5091- to 5150-MHz) airport surface data communications standards development, systems engineering, test bed and prototype development, and tests and demonstrations to establish operational capability for the Aeronautical Mobile Airport Communications System (AeroMACS). Subtask 7-2 focused on systems engineering and development support of the L-band digital aeronautical communications system (L-DACS). Subtask 7-1 consisted of two phases. Phase I included development of AeroMACS concepts of use, requirements, architecture, and initial high-level safety risk assessment. Phase II builds on Phase I results and is presented in two volumes. Volume I (this document) is devoted to concepts of use, system requirements, and architecture, including AeroMACS design considerations. Volume II describes an AeroMACS prototype evaluation and presents final AeroMACS recommendations. This report also describes airport categorization and channelization methodologies. The purposes of the airport categorization task were (1) to facilitate initial AeroMACS architecture designs and enable budgetary projections by creating a set of airport categories based on common airport characteristics and design objectives, and (2) to offer high-level guidance to potential AeroMACS technology and policy development sponsors and service providers. A channelization plan methodology was developed because a common global methodology is needed to assure seamless interoperability among diverse AeroMACS services potentially supplied by multiple service providers.

Results from the Data & Democracy initiative to enhance community-based organization data and research capacity.

Science.gov (United States)

Carroll-Scott, Amy; Toy, Peggy; Wyn, Roberta; Zane, Jazmin I; Wallace, Steven P

2012-07-01

In an era of community-based participatory research and increased expectations for evidence-based practice, we evaluated an initiative designed to increase community-based organizations' data and research capacity through a 3-day train-the-trainer course on community health assessments. We employed a mixed method pre-post course evaluation design. Various data sources collected from 171 participants captured individual and organizational characteristics and pre-post course self-efficacy on 19 core skills, as well as behavior change 1 year later among a subsample of participants. Before the course, participants reported limited previous experience with data and low self-efficacy in basic research skills. Immediately after the course, participants demonstrated statistically significant increases in data and research self-efficacy. The subsample reported application of community assessment skills to their work and increased use of data 1 year later. Results suggest that an intensive, short-term training program can achieve large immediate gains in data and research self-efficacy in community-based organization staff. In addition, they demonstrate initial evidence of longer-term behavior change related to use of data and research skills to support their community work.

Toward an Integrative Perspective on Social Learning in System Innovation Initiatives

Directory of Open Access Journals (Sweden)

Pieter J. Beers

2016-03-01

Full Text Available Sustainability transitions go hand in hand with learning. Theories in the realm of sustainability sciences mostly concentrate on diversity and learning outcomes, whereas theories from the educational sciences mostly focus on learning as an interactive process. In this contribution, we aim to benefit from an integration of these perspectives in order to better understand how different interaction patterns contribute to learning. We studied STAP, an innovation initiative of Dutch greenhouse growers. The Dutch greenhouse sector is predominantly focused on production and efficiency, which causes problems for its future viability. STAP aimed to make the sector more market-oriented while at the same time increasing its societal acceptability (societally responsible innovation. To that end, STAP focused on the development of integrated value chains (primary production, sales, trade that can contribute to a transition towards a societally sensitive greenhouse sector. As action researchers, we collected extensive transcripts of meetings, interviews, and various other documents. We used an open coding strategy to identify different patterns of interaction and the learning outcomes produced by the initiative. We then linked the interaction patterns to the outcomes. Analysis suggests that seemingly negative attack-and-defend patterns of interaction certainly can result in substantial learning results, while seemingly positive synthetic interaction patterns, where participants strive to build on each other, can result in rather bland interaction without substantial outcomes. The results offer an empirical basis to our approach of linking learning interactions to learning outcomes, and it suggests that learning for sustainability can be enhanced by focusing on interaction patterns.

Design of a low cost miniaturized SFCW GPR with initial results

Science.gov (United States)

Duggal, Swati; Sinha, Piyush; Gupta, Manish; Patel, Anand; Vedam, V. V.; Mevada, Pratik; Chavda, Rajesh; Shah, Amita; Putrevu, Deepak

2016-05-01

This paper discusses about the design &developmental of Ground Penetrating Radar (GPR), various scientific and commercial applications of GPR along with the testing and results of GPR at Antarctica for Ice thickness measurement. GPR instruments are categorised as per their frequency of operation, which is inversely proportional to the depth of penetration. GPRs are also categorized as per method of operation which is time-domain or frequency-domain. Indian market is presently procuring GPRs from only foreign suppliers. Space Applications Centre (SAC) had taken up GPR as R&D Technological development with a view to benchmark the technology which may be transferred to local industry for mass production of instrument at a relatively cheaper cost (~20 times cheaper). Hence, this instrument presents a viable indigenous alternative. Also, the design and configuration was targeted for terrestrial as well as future interplanetary (Lander/Rover) missions of ISRO to map subsurface features. The developed GPR has a very large bandwidth (100%, i.e. bandwidth of 500MHz with centre-frequency of 500MHz) and high dynamic range along with the advantage of being highly portable (<10kg). The system was configured as a Stepped-Frequency-Continuous-Wave (SFCW) GPR which is a frequency domain GPR with the aim to increase the detection capabilities with respect to current systems. In order to achieve this goal, innovative electronic equipment have been designed and developed. Three prototypes were developed and two of them have been delivered for Indian Scientific Expedition to Antarctica (ISEA) in 2013 and 2014-15, respectively and promising results have been obtained. The results from the same closely compare with that from commercial GPR too.

Readiness to adopt a performance measurement system for substance abuse treatment: Findings from the Service Quality Measures initiative.

Science.gov (United States)

Myers, B; Petersen Williams, P; Johnson, K; Govender, R; Manderscheid, R; Koch, J R

2017-01-30

A performance measurement system - the Service Quality Measures (SQM) initiative - has been developed to monitor the quality of South Africa (SA)'s substance abuse treatment services. Identifying factors associated with readiness to adopt this system may inform strategies to facilitate its robust implementation. To examine factors associated with readiness to adopt a performance measurement system among SA substance abuse treatment providers. We surveyed 81 treatment providers from 13 treatment sites in the Western Cape, SA. The survey examined awareness, resources, organisational climate, leadership support and readiness to adopt the SQM system. Regression analysis was used to identify factors associated with readiness to adopt this system. Readiness to adopt the SQM initiative was high (M=5.64, standard deviation 1.63). In bivariate analyses, caseload size (F=3.73 (degrees of freedom (df)=3.70), p=0.015), awareness (r=0.78, p<0.0001), leadership support (r=0.70, p<0.0001), resources (r=0.65, p<0.0001), openness to change (r=0.372, p=0.001), and external pressure to change were associated with readiness to adopt the SQM. In multivariate analyses, only awareness of the SQM initiative (B=0.34, standard error (SE) 0.08, t=4.4, p<0.0001) and leadership support (B=0.45, SE 0.11, t=4.0, p<0.0001) were significantly associated with readiness to adopt this system. While treatment providers report high levels of readiness to adopt the SQM system, findings show that the likelihood of adoption can be further increased through improved provider awareness and enhanced leadership support for this health innovation.

Ten Years of Northern Eurasia Earth Science Partnership Initiative (NEESPI): Results and Future Plans

Science.gov (United States)

Groisman, P. Y.; Gutman, G.; Gulev, S.; Maksyutov, S. S.

2014-12-01

During recent decades, Northern Eurasia was affected by unprecedented climate and environmental changes. Several droughts and heat waves alternated with hazardous extreme precipitation and flood events. Permafrost thaw, retreating Arctic sea ice, increasing areas of forest fire, and dramatic regional warming buffeted this region, tossing northern Eurasia from one extreme condition to the next. The region stores nearly half of the Earth's terrestrial carbon in permafrost, wetlands, and forested land, so ecosystem changes that release stored carbon could profoundly affect the world's climate. Furthermore, changes to climate and to hydrological and biogeochemical cycles are starting to affect daily life. For example, infrastructure is collapsing as permafrost thaws, severe winter storms increasingly bring businesses to a halt, and a growing water deficit is beginning to strain agricultural production and forestry. To pool resources and facilitate research, the Northern Eurasia Earth Science Partnership Initiative (NEESPI, http://neespi.org) was launched in 2004. With its multidisciplinary focus, the internationally funded NEESPI (more than165 individual international projects during the past decade) has challenged participants to research climate-ecosystem interactions, societal impacts from extreme events in Northern Eurasia, and the feedbacks of these interactions and impacts to the global Earth system. Among the numerous Institutional and private sponsors from the United States, European Union, Russia, China, and Japan, the cornerstone support for the NEESPI studies was provided by the NASA Land Cover and Land Use Change Program and the Russian Academy of Sciences. At this presentation we shall overview the environmental studies conducted by the NEESPI community, brief the audience about the main achievements of the NEESPI researchers, and lay down the plans for the future studies. At the side event of the Meeting, we are going to initiate preparation of the book

Skill of a global seasonal streamflow forecasting system, relative roles of initial conditions and meteorological forcing

NARCIS (Netherlands)

Candogan Yossef, N.; Winsemius, H.C.; Weerts, A.; Van Beek, R.; Bierkens, M.F.P.

2013-01-01

We investigate the relative contributions of initial conditions (ICs) and meteorological forcing (MF) to the skill of the global seasonal streamflow forecasting system FEWS-World, using the global hydrological model PCRaster Global Water Balance. Potential improvement in forecasting skill through

Road Transport Management System (RTMS): a self regulation initiative in heavy vehicle transport in South Africa

CSIR Research Space (South Africa)

Nordengen, Paul A

2007-07-01

Full Text Available This paper describes the most recent developments of an initiative to introduce meaningful self-regulation in the heavy vehicle transport industry through a Road Transport Management System (RTMS) with the aim of contributing to the road authorities...

Search Results | Page 842 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 8411 - 8420 of 8496 ... Land Tenure, Gender, and Globalization: Research and Analysis from ... Globalization, Labor Markets and Inequality in India ... the results of an international initiative to document the effects of how health systems ...

Search Results | Page 779 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 7781 - 7790 of 9602 ... Land Tenure, Gender, and Globalization: Research and Analysis from ... Globalization, Labor Markets and Inequality in India ... the results of an international initiative to document the effects of how health systems ...

Search Results | Page 842 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 8411 - 8420 of 8491 ... Globalization, Labor Markets and Inequality in India ... results of an international initiative to document the effects of how health systems in ... Natural Resource Management: The Impact of Gender and Social Issues.

[A simplified occupational health and safety management system designed for small enterprises. Initial validation results].

Science.gov (United States)

Bacchi, Romana; Veneri, L; Ghini, P; Caso, Maria Alessandra; Baldassarri, Giovanna; Renzetti, F; Santarelli, R

2009-01-01

Occupational Health and Safety Management Systems (OHSMS) are known to be effective in improving safety at work. Unfortunately they are often too resource-heavy for small businesses. The aim of this project was to develop and test a simplified model of OHSMS suitable for small enterprises. The model consists of 7 procedures and various operating forms and check lists, that guide the enterprise in managing safety at work. The model was tested in 15 volunteer enterprises. In most of the enterprises two audits showed increased awareness and participation of workers; better definition and formalisation of respon sibilities in 8 firms; election of Union Safety Representatives in over one quarter of the enterprises; improvement of safety equipment. The study also helped identify areas where the model could be improved by simplification of unnecessarily complex and redundant procedures.

Hemichorea-hemiballismus as an initial manifestation in a Moroccan ...

African Journals Online (AJOL)

Neurologic signs and symptoms may represent the initial presentation of AIDS in 10-30% of patients. Movement disorders may be the result of direct central nervous system infection by human immunodeficiency virus (HIV) or the result of opportunistic infections. We report the case of a 59 years old woman who had ...

[Support of the nursing process through electronic nursing documentation systems (UEPD) – Initial validation of an instrument].

Science.gov (United States)

Hediger, Hannele; Müller-Staub, Maria; Petry, Heidi

2016-01-01

Electronic nursing documentation systems, with standardized nursing terminology, are IT-based systems for recording the nursing processes. These systems have the potential to improve the documentation of the nursing process and to support nurses in care delivery. This article describes the development and initial validation of an instrument (known by its German acronym UEPD) to measure the subjectively-perceived benefits of an electronic nursing documentation system in care delivery. The validity of the UEPD was examined by means of an evaluation study carried out in an acute care hospital (n = 94 nurses) in German-speaking Switzerland. Construct validity was analyzed by principal components analysis. Initial references of validity of the UEPD could be verified. The analysis showed a stable four factor model (FS = 0.89) scoring in 25 items. All factors loaded ≥ 0.50 and the scales demonstrated high internal consistency (Cronbach's α = 0.73 – 0.90). Principal component analysis revealed four dimensions of support: establishing nursing diagnosis and goals; recording a case history/an assessment and documenting the nursing process; implementation and evaluation as well as information exchange. Further testing with larger control samples and with different electronic documentation systems are needed. Another potential direction would be to employ the UEPD in a comparison of various electronic documentation systems.

Initial digital vasculitis in a large multicenter cohort of childhood-onset systemic lupus erythematosus

Directory of Open Access Journals (Sweden)

Ana Paula Sakamoto

Full Text Available Abstract Objectives: To assess clinical digital vasculitis (DV as an initial manifestation of childhood-onset systemic lupus erythematosus (cSLE within a large population. Methods: Multicenter cross-sectional study including 852 cSLE patients (ACR criteria followed in ten Pediatric Rheumatology centers in São Paulo State, Brazil. Results: DV was observed in 25/852 (3% cSLE patients. Periungual hemorrhage was diagnosed in 12 (48%, periungual infarction in 7 (28%, tip finger ulceration in 4 (16%, painful nodules in 1 (4% and gangrene in 1 (4%. A poor outcome, with digital resorption, occurred in 5 (20%. Comparison of patients with and without DV revealed higher frequency of malar rash (80% vs. 53%, p = 0.008, discoid rash (16% vs. 4%, p = 0.017, photosensitivity (76% vs. 45%, p = 0.002 and other cutaneous vasculitides (80% vs. 19%, p 0.05. SLEDAI-2K median, DV descriptor excluded, was significantly lower in patients with DV compared to those without this manifestation [10 (0-28 vs. 14 (0-58, p = 0.004]. Visceral vasculitis or death were not observed in this cSLE cohort. The frequency of cyclophosphamide use (0% vs. 18%, p = 0.014 was significantly lower in the DV group. Conclusion: Our large multicenter study identified clinical DV as one of the rare initial manifestation of active cSLE associated with a mild multisystemic disease, in spite of digital resorption in some of these patients.

National strategy for suicide prevention in Japan: impact of a national fund on progress of developing systems for suicide prevention and implementing initiatives among local authorities.

Science.gov (United States)

Nakanishi, Miharu; Yamauchi, Takashi; Takeshima, Tadashi

2015-01-01

In Japan, the Cabinet Office released the 'General Principles of Suicide Prevention Policy' in 2007 and suggested nine initiatives. In 2009, a national fund was launched to help prefectures (the administrative divisions of Japan) and local authorities implement five categories of suicide-prevention programs. This paper examines the impact of the national fund on the establishment of the systems for suicide prevention and the implementation of these initiatives among local authorities. The present study included 1385 local authorities (79.5%) from all 47 prefectures that responded to the cross-sectional questionnaire survey. Improved suicide-prevention systems and the implementation of nine initiatives in April 2013 were observed among 265 local authorities (19.1%) that implemented 'Training of community service providers' and 'Public awareness campaigns'; 178 local authorities (12.9%) that implemented 'Face-to-face counseling', 'Training of community service providers' and 'Public awareness campaigns'; and 324 local authorities (23.4%) that implemented 'Trauma-informed policies and practices'. There was no significant difference in suicide-prevention systems and the implementation of nine initiatives between 203 local authorities (14.7%) that implemented only 'Public awareness campaigns' and 231 local authorities (16.7%) that did not implement any suicide-prevention programs. The results of our study suggest that the national fund promoted the establishment of community systems for suicide prevention and helped implement initiatives among local authorities. The national suicide-prevention strategy in Japan should explore a standard package of programs to guide community suicide-prevention efforts with a sustained workforce among local authorities. © 2014 The Authors. Psychiatry and Clinical Neurosciences © 2014 Japanese Society of Psychiatry and Neurology.

Environment and initial state engineered dynamics of quantum and classical correlations

Energy Technology Data Exchange (ETDEWEB)

Wang, Cheng-Zhi, E-mail: czczwang@outlook.com; Li, Chun-Xian; Guo, Yu; Lu, Geng-Biao; Ding, Kai-He

2016-11-15

Based on an open exactly solvable system coupled to an environment with nontrivial spectral density, we connect the features of quantum and classical correlations with some features of the environment, initial states of the system, and the presence of initial system–environment correlations. Some interesting features not revealed before are observed by changing the structure of environment, the initial states of system, and the presence of initial system–environment correlations. The main results are as follows. (1) Quantum correlations exhibit temporary freezing and permanent freezing even at high temperature of the environment, for which the necessary and sufficient conditions are given by three propositions. (2) Quantum correlations display a transition from temporary freezing to permanent freezing by changing the structure of environment. (3) Quantum correlations can be enhanced all the time, for which the condition is put forward. (4) The one-to-one dependency relationship between all kinds of dynamic behaviors of quantum correlations and the initial states of the system as well as environment structure is established. (5) In the presence of initial system–environment correlations, quantum correlations under local environment exhibit temporary multi-freezing phenomenon. While under global environment they oscillate, revive, and damp, an explanation for which is given. - Highlights: • Various interesting behaviors of quantum and classical correlations are observed in an open exactly solvable model. • The important effects of the bath structure on quantum and classical correlations are revealed. • The one-to-one correspondence between the type of dynamical behavior of quantum discord and the initial state is given. • Quantum correlations are given in the presence of initial qubits–bath correlations.

Environment and initial state engineered dynamics of quantum and classical correlations

International Nuclear Information System (INIS)

Wang, Cheng-Zhi; Li, Chun-Xian; Guo, Yu; Lu, Geng-Biao; Ding, Kai-He

2016-01-01

Based on an open exactly solvable system coupled to an environment with nontrivial spectral density, we connect the features of quantum and classical correlations with some features of the environment, initial states of the system, and the presence of initial system–environment correlations. Some interesting features not revealed before are observed by changing the structure of environment, the initial states of system, and the presence of initial system–environment correlations. The main results are as follows. (1) Quantum correlations exhibit temporary freezing and permanent freezing even at high temperature of the environment, for which the necessary and sufficient conditions are given by three propositions. (2) Quantum correlations display a transition from temporary freezing to permanent freezing by changing the structure of environment. (3) Quantum correlations can be enhanced all the time, for which the condition is put forward. (4) The one-to-one dependency relationship between all kinds of dynamic behaviors of quantum correlations and the initial states of the system as well as environment structure is established. (5) In the presence of initial system–environment correlations, quantum correlations under local environment exhibit temporary multi-freezing phenomenon. While under global environment they oscillate, revive, and damp, an explanation for which is given. - Highlights: • Various interesting behaviors of quantum and classical correlations are observed in an open exactly solvable model. • The important effects of the bath structure on quantum and classical correlations are revealed. • The one-to-one correspondence between the type of dynamical behavior of quantum discord and the initial state is given. • Quantum correlations are given in the presence of initial qubits–bath correlations.

Cascade Distiller System Performance Testing Interim Results

Science.gov (United States)

Callahan, Michael R.; Pensinger, Stuart; Sargusingh, Miriam J.

2014-01-01

The Cascade Distillation System (CDS) is a rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. Based upon the results of the 2009 distillation comparison test (DCT) and recommendations of the expert panel, the Advanced Exploration Systems (AES) Water Recovery Project (WRP) project advanced the technology by increasing reliability of the system through redesign of bearing assemblies and improved rotor dynamics. In addition, the project improved the CDS power efficiency by optimizing the thermoelectric heat pump (TeHP) and heat exchanger design. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell d International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades as compared to previous system performance. The system was challenged with Solution 1 from the NASA Exploration Life Support (ELS) distillation comparison testing performed in 2009. Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. A secondary objective of this testing is to evaluate the performance of the CDS as compared to the state of the art Distillation Assembly (DA) used in the ISS Urine Processor Assembly (UPA). This was done by challenging the system with ISS analog waste streams. This paper details the results of the AES WRP CDS performance testing.

Adherence of private health system hospitals to dissemination of outcomes according to the Global Reporting Initiative (GRI) model.

Science.gov (United States)

Machado, Celso; César, Robson Danúbio da Silva; Souza, Maria Tereza Saraiva de

2017-01-01

To verify if there is an analogy between the indicators of the Global Reporting Initiative adopted by hospitals in the private healthcare system. Documentary research supported by reports that are electronically available on the website of the companies surveyed. The organizations surveyed had a significant adherence of their economic, social and environmental indicators of the model proposed by the Global Reporting Initiative, showing an analogous field of common indicators between them. There is similarity between the indicators adopted by companies, but one of the hospitals analyzed had a greater number of converging indicators to Global Reporting Initiative.

RHIC Beam Loss Monitor System Initial Operation

International Nuclear Information System (INIS)

Witkover, R. L.; Michnoff, R. J.; Geller, J. M.

1999-01-01

The RHIC Beam Loss Monitor (BLM) System is designed to prevent beam loss quenching of the superconducting magnets, and acquire loss data. Four hundred ion chambers are located around the rings to detect losses. The required 8-decade range in signal current is compressed using an RC pre-integrator ahead of a low current amplifier. A beam abort may be triggered if fast or slow losses exceed programmable threshold levels. A micro-controller based VME module sets references and gains and reads trip status for up to 64 channels. Results obtained with the detectors in the RHIC Sextant Test and the prototype electronics in the AGS-to-RHIC (AtR) transfer line are presented along with the present status of the system

Global Positioning System receiver evaluation results

Energy Technology Data Exchange (ETDEWEB)

Byrne, R.H.

1993-09-01

A Sandia project currently uses an outdated Magnavox 6400 Global Positioning System (GPS) receiver as the core of its navigation system. The goal of this study was to analyze the performance of the current GPS receiver compared to newer, less expensive models and to make recommendations on how to improve the performance of the overall navigation system. This paper discusses the test methodology used to experimentally analyze the performance of different GPS receivers, the test results, and recommendations on how an upgrade should proceed. Appendices contain detailed information regarding the raw data, test hardware, and test software.

Initial results from SKiYMET meteor radar at Thumba (8.5°N, 77°E): 1. Comparison of wind measurements with MF spaced antenna radar system

Science.gov (United States)

Kumar, Karanam Kishore; Ramkumar, Geetha; Shelbi, S. T.

2007-12-01

In the present communication, initial results from the allSKy interferometric METeor (SKiYMET) radar installed at Thumba (8.5°N, 77°E) are presented. The meteor radar system provides hourly zonal and meridional winds in the mesosphere lower thermosphere (MLT) region. The meteor radar measured zonal and meridional winds are compared with nearby MF radar at Tirunalveli (8.7°N, 77.8°E). The present study provided an opportunity to compare the winds measured by the two different techniques, namely, interferometry and spaced antenna drift methods. Simultaneous wind measurements for a total number of 273 days during September 2004 to May 2005 are compared. The comparison showed a very good agreement between these two techniques in the height region 82-90 km and poor agreement above this height region. In general, the zonal winds compare very well as compared to the meridional winds. The observed discrepancies in the wind comparison above 90 km are discussed in the light of existing limitations of both the radars. The detailed analysis revealed the consistency of the measured winds by both the techniques. However, the discrepancies are observed at higher altitudes and are attributed to the contamination of MF radar neutral wind measurements with Equatorial Electro Jet (EEJ) induced inospheric drifts rather than the limitations of the spaced antenna technique. The comparison of diurnal variation of zonal winds above 90 km measured by both the radars is in reasonably good agreement in the absence of EEJ (during local nighttime). It is also been noted that the difference in the zonal wind measurements by both the radars is directly related to the strength of EEJ, which is a noteworthy result from the present study.

Policies and Initiatives for Carbon Neutrality in Nordic

DEFF Research Database (Denmark)

Wu, Qiuwei; Møller, Jakob Glarbo; Østergaard, Jacob

2013-01-01

Policies and initiatives promoting carbon neutrality in the Nordic heating and transport systems are presented. The focus within heating systems is the promotion of HPs (heat pumps) while the focus within transport systems is initiatives regarding EVs (electric vehicles). It is found...... for the future heating and transport systems with the ambition of realizing carbon neutrality...... that the conversion to HPs in the Nordic region relies on both private economic and national economic incentives. Initiatives toward carbon neutrality in the transport system are mostly concentrated on research, development and demonstration for deployment of a large number of EVs. All Nordic countries have plans...

Initial results from an agressive roentgenological and surgical approach to acute mesenteric ischemia.

Science.gov (United States)

Boley, S J; Sprayregan, S; Siegelman, S S; Veith, F J

1977-12-01

The 70% to 80% mortality rate of patients with acute mesenteric ischemia (AMI) has remained unchanged over the past 40 years. We report here the initial results using an aggressive approach to this problem. This included the earlier and more liberal use of angiography in patients at risk and the intra-arterial infusion of papaverine for the relief of superior mesenteric artery (SMA) vasoconstriction in both nonocclusive and occlusive forms of AMI. Of the first 50 patients managed by this approach, 35 (70%) had AMI demonstrated by SMA angiography, Nineteen (54%) of these 35 patients survived, including nine of 15 patients with nonocclusive mesenteric ischemia, seven of 16 with SMA embolus, two of three patients with SMA thrombosis, and the one patient with mesenteric venous thrombosis. Seventeen of the 19 survivors lost no bowel or had excision of less than 3 feet of small intestine.

Polymerization of acrylamide initiated with Ce(IV- and KMnO4–mercaptosuccinic acid redox systems in acid-aqueous medium

Directory of Open Access Journals (Sweden)

2007-03-01

Full Text Available By using mercaptosuccinic acid-cerium(IV sulfate and mercaptosuccinic acid-KMnO4 redox systems in acid aqueous medium, the polymerization of acrylamide monomer was performed at room temperatures. Water soluble acrylamide polymers which contain mercaptosuccinic acid end-groups were synthesized. The dependence of polymerization yield and the molecular weight of polymer on the initiator concentration(nMSA=nCe(IV at different acid concentrations, polymerization time, temperature, and concentration of sulfuric acid was investigated. The decrease in the initiator concentration resulted in an increase in the molecular weights but a decrease in the yield. The increase of reaction temperature from 20 to 60°C resulted in an increase in the molecular weights and slight decrease of the yield of polymer. Cerium and manganese ions are reduced to Ce(III and Mn(II ions respectively in polymerization reaction. The existence of Ce(III ion bound to polymer was investigated by UV-visible spectrometry and fluorescence measurements. The amount of Mn(II which is incorporated to the polymer was determined.

KINETICS OF POLYMERIZATION OF METHYL METHACRYLATE INITIATED BY COPPER POLYPROPYLENE-BASED POLYAMIDOXIME-SODIUM SULFITE SYSTEM

Institute of Scientific and Technical Information of China (English)

WU Jinyuan; YANG Yiguang; YANG Chaoxiong

1992-01-01

The aqueous polymerization of methyl methacrylate initiated by copper polypropylene-based polyamidoxime ( PPAO - Cu ) - sodium sulfite system was investigated . The overall rate of polymerization (Rp) is Rp=9.7 × 1012 e-21, 200/RT [MMA]0.88 [ Na2 SO 3 ]0.50 The length of the induction period (τ) is inversely proportional to the concentration of sodium sulfite and independent of the amount of polymer supported copper and the concentration of monomer. It could be expressed as follows:1τ=1.2× 1012e-15,600/RT[ Na2SO3] =KτRi The polymerization is initiated by a primary radical generated from the redox reaction rather than induced by "coordination-proton transfer" mechanism.

Photoirradiation system with depth optical dosimetry control in initial oxygen saturation measurement

International Nuclear Information System (INIS)

Quintanar, L.; Stolik, S.; Rosa, J. de la; Moreno, E.

2012-01-01

Photodynamic Therapy is a technique in which a photosensitizing substance is applied that is activated by light and it generates reactive oxygen species which cause selective cell destruction. The efficiency of the therapy is affected by the parameters dose. In this work it is shown a photo-irradiation system for superficial Photodynamic Therapy, using as a light source a light emitting diode with an automatic control of optical power based on a model of the distribution of light in depth that was tested in tissue phantoms. It also has a reflective pulse oximeter for the measurement of the initial oxygen saturation. (Author)

Initial reconstruction results from a simulated adaptive small animal C shaped PET/MR insert

Energy Technology Data Exchange (ETDEWEB)

Efthimiou, Nikos [Technological Educational Institute of Athens (Greece); Kostou, Theodora; Papadimitroulas, Panagiotis [Technological Educational Institute of Athens (Greece); Department of Medical Physics, School of Medicine, University of Patras (Greece); Charalampos, Tsoumpas [Division of Biomedical Imaging, University of Leeds, Leeds (United Kingdom); Loudos, George [Technological Educational Institute of Athens (Greece)

2015-05-18

Traditionally, most clinical and preclinical PET scanners, rely on full cylindrical geometry for whole body as well as dedicated organ scans, which is not optimized with regards to sensitivity and resolution. Several groups proposed the construction of dedicated PET inserts for MR scanners, rather than the construction of new integrated PET/MR scanners. The space inside an MR scanner is a limiting factor which can be reduced further with the use of extra coils, and render the use of non-flexible cylindrical PET scanners difficult if not impossible. The incorporation of small SiPM arrays, can provide the means to design adaptive PET scanners to fit in tight locations, which, makes imaging possible and improve the sensitivity, due to the closer approximation to the organ of interest. In order to assess the performance of such a device we simulated the geometry of a C shaped PET, using GATE. The design of the C-PET was based on a realistic SiPM-BGO scenario. In order reconstruct the simulated data, with STIR, we had to calculate system probability matrix which corresponds to this non standard geometry. For this purpose we developed an efficient multi threaded ray tracing technique to calculate the line integral paths in voxel arrays. One of the major features is the ability to automatically adjust the size of FOV according to the geometry of the detectors. The initial results showed that the sensitivity improved as the angle between the detector arrays increases, thus better angular sampling the scanner's field of view (FOV). The more complete angular coverage helped in improving the shape of the source in the reconstructed images, as well. Furthermore, by adapting the FOV to the closer to the size of the source, the sensitivity per voxel is improved.

Initial reconstruction results from a simulated adaptive small animal C shaped PET/MR insert

International Nuclear Information System (INIS)

Efthimiou, Nikos; Kostou, Theodora; Papadimitroulas, Panagiotis; Charalampos, Tsoumpas; Loudos, George

2015-01-01

Traditionally, most clinical and preclinical PET scanners, rely on full cylindrical geometry for whole body as well as dedicated organ scans, which is not optimized with regards to sensitivity and resolution. Several groups proposed the construction of dedicated PET inserts for MR scanners, rather than the construction of new integrated PET/MR scanners. The space inside an MR scanner is a limiting factor which can be reduced further with the use of extra coils, and render the use of non-flexible cylindrical PET scanners difficult if not impossible. The incorporation of small SiPM arrays, can provide the means to design adaptive PET scanners to fit in tight locations, which, makes imaging possible and improve the sensitivity, due to the closer approximation to the organ of interest. In order to assess the performance of such a device we simulated the geometry of a C shaped PET, using GATE. The design of the C-PET was based on a realistic SiPM-BGO scenario. In order reconstruct the simulated data, with STIR, we had to calculate system probability matrix which corresponds to this non standard geometry. For this purpose we developed an efficient multi threaded ray tracing technique to calculate the line integral paths in voxel arrays. One of the major features is the ability to automatically adjust the size of FOV according to the geometry of the detectors. The initial results showed that the sensitivity improved as the angle between the detector arrays increases, thus better angular sampling the scanner's field of view (FOV). The more complete angular coverage helped in improving the shape of the source in the reconstructed images, as well. Furthermore, by adapting the FOV to the closer to the size of the source, the sensitivity per voxel is improved.

Neonatal screening for four lysosomal storage diseases with a digital microfluidics platform: Initial results in Brazil

Directory of Open Access Journals (Sweden)

Eurico Camargo Neto

2018-06-01

Full Text Available Abstract We describe the initial results of a neonatal screening program for four lysosomal storage diseases (MPS I, Pompe, Gaucher and Fabry using the digital microfluidics methodology. The method successfully identified patients previously diagnosed with these diseases and was used to test dried blood spot samples obtained from 10,527 newborns aged 2 to 14 days. The digital microfluidic technology shows potential for a simple, rapid and high-throughput screening for these four diseases in a standard neonatal screening laboratory.

A Trigonometrically Fitted Block Method for Solving Oscillatory Second-Order Initial Value Problems and Hamiltonian Systems

OpenAIRE

Ngwane, F. F.; Jator, S. N.

2017-01-01

In this paper, we present a block hybrid trigonometrically fitted Runge-Kutta-Nyström method (BHTRKNM), whose coefficients are functions of the frequency and the step-size for directly solving general second-order initial value problems (IVPs), including Hamiltonian systems such as the energy conserving equations and systems arising from the semidiscretization of partial differential equations (PDEs). Four discrete hybrid formulas used to formulate the BHTRKNM are provided by a continuous one...

RQ-21A Blackjack Small Tactical Unmanned Aircraft System (STUAS): Initial Operational Test and Evaluation Report

Science.gov (United States)

2015-06-29

Evaluation Report June 2015 This report on the RQ-21A Blackjack Small Tactical Unmanned Aircraft System fulfills the provisions of Title 10...suitability of the RQ-21A Blackjack Small Tactical Unmanned Aircraft System (STUAS) during Initial Operational Test and Evaluation (IOT&E). The Navy’s...66.9 percent). The average service life of the propulsion modules was 48.9 hours, which does not meet the manufacturer’s stated 100-hour

Towards a regional coastal ocean observing system: An initial design for the Southeast Coastal Ocean Observing Regional Association

Science.gov (United States)

Seim, H. E.; Fletcher, M.; Mooers, C. N. K.; Nelson, J. R.; Weisberg, R. H.

2009-05-01

A conceptual design for a southeast United States regional coastal ocean observing system (RCOOS) is built upon a partnership between institutions of the region and among elements of the academic, government and private sectors. This design envisions support of a broad range of applications (e.g., marine operations, natural hazards, and ecosystem-based management) through the routine operation of predictive models that utilize the system observations to ensure their validity. A distributed information management system enables information flow, and a centralized information hub serves to aggregate information regionally and distribute it as needed. A variety of observing assets are needed to satisfy model requirements. An initial distribution of assets is proposed that recognizes the physical structure and forcing in the southeast U.S. coastal ocean. In-situ data collection includes moorings, profilers and gliders to provide 3D, time-dependent sampling, HF radar and surface drifters for synoptic sampling of surface currents, and satellite remote sensing of surface ocean properties. Nested model systems are required to properly represent ocean conditions from the outer edge of the EEZ to the watersheds. An effective RCOOS will depend upon a vital "National Backbone" (federally supported) system of in situ and satellite observations, model products, and data management. This dependence highlights the needs for a clear definition of the National Backbone components and a Concept of Operations (CONOPS) that defines the roles, functions and interactions of regional and federal components of the integrated system. A preliminary CONOPS is offered for the Southeast (SE) RCOOS. Thorough system testing is advocated using a combination of application-specific and process-oriented experiments. Estimates of costs and personnel required as initial components of the SE RCOOS are included. Initial thoughts on the Research and Development program required to support the RCOOS are

Analysis of Summertime Convective Initiation in Central Alabama Using the Land Information System

Science.gov (United States)

James, Robert S.; Case, Jonathan L.; Molthan, Andrew L.; Jedlovec, Gary J.

2011-01-01

During the summer months in the southeastern United States, convective initiation presents a frequent challenge to operational forecasters. Thunderstorm development has traditionally been referred to as random due to their disorganized, sporadic appearance and lack of atmospheric forcing. Horizontal variations in land surface characteristics such as soil moisture, soil type, land and vegetation cover could possibly be a focus mechanism for afternoon convection during the summer months. The NASA Land Information System (LIS) provides a stand-alone land surface modeling framework that incorporates these varying soil and vegetation properties, antecedent precipitation, and atmospheric forcing to represent the soil state at high resolution. The use of LIS as a diagnostic tool may help forecasters to identify boundaries in land surface characteristics that could correlate to favored regions of convection initiation. The NASA Shortterm Prediction Research and Transition (SPoRT) team has been collaborating with the National Weather Service Office in Birmingham, AL to help incorporate LIS products into their operational forecasting methods. This paper highlights selected convective case dates from summer 2009 when synoptic forcing was weak, and identifies any boundaries in land surface characteristics that may have contributed to convective initiation. The LIS output depicts the effects of increased sensible heat flux from urban areas on the development of convection, as well as convection along gradients in land surface characteristics and surface sensible and latent heat fluxes. These features may promote mesoscale circulations and/or feedback processes that can either enhance or inhibit convection. With this output previously unavailable to operational forecasters, LIS provides a new tool to forecasters in order to help eliminate the randomness of summertime convective initiation.

Pediatric Biopharmaceutical Classification System: Using Age-Appropriate Initial Gastric Volume.

Science.gov (United States)

Shawahna, Ramzi

2016-05-01

Development of optimized pediatric formulations for oral administration can be challenging, time consuming, and financially intensive process. Since its inception, the biopharmaceutical classification system (BCS) has facilitated the development of oral drug formulations destined for adults. At least theoretically, the BCS principles are applied also to pediatrics. A comprehensive age-appropriate BCS has not been fully developed. The objective of this work was to provisionally classify oral drugs listed on the latest World Health Organization's Essential Medicines List for Children into an age-appropriate BCS. A total of 38 orally administered drugs were included in this classification. Dose numbers were calculated using age-appropriate initial gastric volume for neonates, 6-month-old infants, and children aging 1 year through adulthood. Using age-appropriate initial gastric volume and British National Formulary age-specific dosing recommendations in the calculation of dose numbers, the solubility classes shifted from low to high in pediatric subpopulations of 12 years and older for amoxicillin, 5 years, 12 years and older for cephalexin, 9 years and older for chloramphenicol, 3-4 years, 9-11 and 15 years and older for diazepam, 18 years and older (adult) for doxycycline and erythromycin, 8 years and older for phenobarbital, 10 years and older for prednisolone, and 15 years and older for trimethoprim. Pediatric biopharmaceutics are not fully understood where several knowledge gaps have been recently emphasized. The current biowaiver criteria are not suitable for safe application in all pediatric populations.

EPA program to demonstrate mitigation measures for indoor radon: initial results

International Nuclear Information System (INIS)

Henschel, D.B.; Scott, A.G.

1986-01-01

EPA has installed radon mitigation techniques in 18 concrete block basement homes in the Reading Prong region of eastern Pennsylvania. Three alternative active soil ventilation approaches were tested: suction on the void network within the concrete block basement walls; suction on the footing drain tile system; and suction on the aggregate underneath the concrete slab. The initial 18 mitigation installations were designed to demonstrate techniques which would have low to moderate installation and operating costs. Where effective closure of major openings in the block walls is possible, suction on the wall voids has proved to be extremely effective, able to reduce homes having very high radon Working Levels (up to 7 WL) to 0.02 WL and less. However, where inaccessible major openings are concealed within the wall, it is more difficult and/or more expensive to develop adequate suction on the void network, and performance is reduced. Testing is continuing to demonstrate the steps required to achieve high performance with wall suction in homes with such difficult-to close walls. Drain tile suction can be very effective where the drain tiles completely surround the home; drain tile suction is the least expensive and most aesthetic of the active soil ventilation approaches, but appears susceptible to spikes in radon levels when the basement is depressurized. Sub-slab suction as tested in this study - with one or two individual suction points in the slab - does not appear adequate to ensure sustained high levels of reduction on block wall basement homes; it appears to effectively treat slab-related soil gas entry routes so long as a uniform layer of aggregate is present, but it does not appear to effectively treat the wall-related entry routes. Closure of major openings might have improved sub-slab suction performance. 5 figures, 3 tables

NMR imaging of the brain: initial impressions

International Nuclear Information System (INIS)

Spencer, D.H.; Bydder, G.M.

1983-01-01

An NMR imaging system designed and built by Thorn-EMI Ltd was installed at Hammersmith Hospital in March 1981. In the first year of operation 180 patients and 40 volunteers have had cranial examinations and initial impressions bases on this experience are presented. Patients with a wide variety of neurological diseases have been studied to provide a basis for diagnostic interpretation, to define distinctive features, and to evaluate different types of scanning sequences. NMR imaging appears to be of considerable value in neurological diagnosis and has a number of advantages over CT. The detailed evaluation of NMR imaging will require much more work but the initial results are very promising

Advanced Monitoring Systems Initiative Project Achievements for Environmental Restoration and Waste Management

International Nuclear Information System (INIS)

Hohman, E.H.; Lohrstorfer, C.L.; Venedam, R.J.; Weeks, S.J.; Fannin, C.R.

2006-01-01

The Advanced Monitoring Systems Initiative (AMSI) project has been in existence since 2002. In this short time period, AMSI has successfully developed, tested and/or demonstrated over 30 advanced sensors and monitoring systems for applications in environmental restoration, waste management and other areas of national interest. This presentation summarizes the AMSI project, and gives examples of recent successes. The purpose of the presentation is to make Symposium attendees aware of AMSI's capabilities and experience, for possible use in the future. Example successes include the following: - Automated hexavalent chromium (Cr(VI)) monitoring in wells alongside the Columbia River; - Atmospheric chemical sensor array for remote, real-time plume tracking; - Wireless sensor platform for long-term monitoring of subsurface moisture; - Embedded piezo-resistive micro-cantilever (EPM) units for carbon tetrachloride (CCl 4 ) and hydrogen cyanide (HCN) detection; - 'iHistorian' for efficient, real-time data management of chemical releases. (authors)

Instrumented Pipeline Initiative

Energy Technology Data Exchange (ETDEWEB)

Thomas Piro; Michael Ream

2010-07-31

This report summarizes technical progress achieved during the cooperative agreement between Concurrent Technologies Corporation (CTC) and U.S. Department of Energy to address the need for a for low-cost monitoring and inspection sensor system as identified in the Department of Energy (DOE) National Gas Infrastructure Research & Development (R&D) Delivery Reliability Program Roadmap.. The Instrumented Pipeline Initiative (IPI) achieved the objective by researching technologies for the monitoring of pipeline delivery integrity, through a ubiquitous network of sensors and controllers to detect and diagnose incipient defects, leaks, and failures. This report is organized by tasks as detailed in the Statement of Project Objectives (SOPO). The sections all state the objective and approach before detailing results of work.

Fast pyrolysis in a novel wire-mesh reactor: design and initial results

NARCIS (Netherlands)

Hoekstra, E.; van Swaaij, Willibrordus Petrus Maria; Kersten, Sascha R.A.; Hogendoorn, Kees

2012-01-01

Pyrolysis is known to occur by decomposition processes followed by vapour phase reactions. The goal of this research is to develop a novel device to study the initial decomposition processes. For this, a novel wire-mesh reactor was constructed. A small sample (<0.1 g) was clamped between two meshes

Correlation of Persistence, Initiative and Career Anchors Categories of Students

Directory of Open Access Journals (Sweden)

I A Novikova

2008-03-01

Full Text Available The article is devoted to the analysis of the results of comparative empirical study of persistence, initiative and Career Anchors categories of the students on the basis of the systemic-functional approach.

The Role of NASA's Planetary Data System in the Planetary Spatial Data Infrastructure Initiative

Science.gov (United States)

Arvidson, R. E.; Gaddis, L. R.

2017-12-01

An effort underway in NASA's planetary science community is the Mapping and Planetary Spatial Infrastructure Team (MAPSIT, http://www.lpi.usra.edu/mapsit/). MAPSIT is a community assessment group organized to address a lack of strategic spatial data planning for space science and exploration. Working with MAPSIT, a new initiative of NASA and USGS is the development of a Planetary Spatial Data Infrastructure (PSDI) that builds on extensive knowledge on storing, accessing, and working with terrestrial spatial data. PSDI is a knowledge and technology framework that enables the efficient discovery, access, and exploitation of planetary spatial data to facilitate data analysis, knowledge synthesis, and decision-making. NASA's Planetary Data System (PDS) archives >1.2 petabytes of digital data resulting from decades of planetary exploration and research. The PDS charter focuses on the efficient collection, archiving, and accessibility of these data. The PDS emphasis on data preservation and archiving is complementary to that of the PSDI initiative because the latter utilizes and extends available data to address user needs in the areas of emerging technologies, rapid development of tailored delivery systems, and development of online collaborative research environments. The PDS plays an essential PSDI role because it provides expertise to help NASA missions and other data providers to organize and document their planetary data, to collect and maintain the archives with complete, well-documented and peer-reviewed planetary data, to make planetary data accessible by providing online data delivery tools and search services, and ultimately to ensure the long-term preservation and usability of planetary data. The current PDS4 information model extends and expands PDS metadata and relationships between and among elements of the collections. The PDS supports data delivery through several node services, including the Planetary Image Atlas (https

Decadal predictions of Southern Ocean sea ice : testing different initialization methods with an Earth-system Model of Intermediate Complexity

Science.gov (United States)

Zunz, Violette; Goosse, Hugues; Dubinkina, Svetlana

2013-04-01

The sea ice extent in the Southern Ocean has increased since 1979 but the causes of this expansion have not been firmly identified. In particular, the contribution of internal variability and external forcing to this positive trend has not been fully established. In this region, the lack of observations and the overestimation of internal variability of the sea ice by contemporary General Circulation Models (GCMs) make it difficult to understand the behaviour of the sea ice. Nevertheless, if its evolution is governed by the internal variability of the system and if this internal variability is in some way predictable, a suitable initialization method should lead to simulations results that better fit the reality. Current GCMs decadal predictions are generally initialized through a nudging towards some observed fields. This relatively simple method does not seem to be appropriated to the initialization of sea ice in the Southern Ocean. The present study aims at identifying an initialization method that could improve the quality of the predictions of Southern Ocean sea ice at decadal timescales. We use LOVECLIM, an Earth-system Model of Intermediate Complexity that allows us to perform, within a reasonable computational time, the large amount of simulations required to test systematically different initialization procedures. These involve three data assimilation methods: a nudging, a particle filter and an efficient particle filter. In a first step, simulations are performed in an idealized framework, i.e. data from a reference simulation of LOVECLIM are used instead of observations, herein after called pseudo-observations. In this configuration, the internal variability of the model obviously agrees with the one of the pseudo-observations. This allows us to get rid of the issues related to the overestimation of the internal variability by models compared to the observed one. This way, we can work out a suitable methodology to assess the efficiency of the

Tank waste remediation system retrieval and disposal mission initial updated baseline summary

International Nuclear Information System (INIS)

Swita, W.R.

1998-01-01

This document provides a summary of the Tank Waste Remediation System (TWRS) Retrieval and Disposal Mission Initial Updated Baseline (scope, schedule, and cost), developed to demonstrate Readiness-to-Proceed (RTP) in support of the TWRS Phase 1B mission. This Updated Baseline is the proposed TWRS plan to execute and measure the mission work scope. This document and other supporting data demonstrate that the TWRS Project Hanford Management Contract (PHMC) team is prepared to fully support Phase 1B by executing the following scope, schedule, and cost baseline activities: Deliver the specified initial low-activity waste (LAW) and high-level waste (HLW) feed batches in a consistent, safe, and reliable manner to support private contractors' operations starting in June 2002; Deliver specified subsequent LAW and HLW feed batches during Phase 1B in a consistent, safe, and reliable manner; Provide for the interim storage of immobilized HLW (IHLW) products and the disposal of immobilized LAW (ILAW) products generated by the private contractors; Provide for disposal of byproduct wastes generated by the private contractors; and Provide the infrastructure to support construction and operations of the private contractors' facilities

Applying a global justice lens to health systems research ethics: an initial exploration.